Powered by Deep Web Technologies
Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Property:AvgReservoirDepth | Open Energy Information  

Open Energy Info (EERE)

AvgReservoirDepth AvgReservoirDepth Jump to: navigation, search Property Name AvgReservoirDepth Property Type Quantity Description Average depth to reservoir Use this type to express a quantity of length. The default unit is the meter (m). Acceptable units (and their conversions) are: Meters - 1 m, meter, meters Meter, Meters, METER, METERS Kilometers - 0.001 km, kilometer, kilometers, Kilometer, Kilometers, KILOMETERS, KILOMETERS Miles - 0.000621371 mi, mile, miles, Mile, Miles, MILE, MILES Feet - 3.28084 ft, foot, feet, Foot, Feet, FOOT, FEET Yards - 1.09361 yd, yard, yards, Yard, Yards, YARD, YARDS Pages using the property "AvgReservoirDepth" Showing 24 pages using this property. A Amedee Geothermal Area + 213 m0.213 km 0.132 mi 698.819 ft 232.939 yd + B Beowawe Hot Springs Geothermal Area + 850 m0.85 km

2

Determination of capillary displacement pressure and representative average capillary pressure vs. depth in shally sandstones from well logs  

SciTech Connect

This research presents a method whereby the capillary displacement pressure Pcd and the representative average capillary pressure in shaly sandstone reservoirs exhibits continuous information vs. depth from well logs. By the aid of special core analysis, correlation functions were obtained that relate the capillary characteristics of the reservoir rock to its lithologic development. Since the lithologic influence factor is a well log-derived parameter the correlations then were used to determine by means of well logs the capillary displacement and average capillary pressures for borehole sections where special core analysis is not available. This technique has been developed and applied to the shaly sandstone reservoir of the Sarir oil field in Libya.

Barlai, Z.; Berruin, N.A.; Mawla, R.A.

1981-01-01T23:59:59.000Z

3

Petroleum reservoir porosity versus depth: Influence of geological age  

Science Journals Connector (OSTI)

...in late Carboniferous sandstone reservoirs, Bothamsall oilfield, E. Midlands: Journal of the Geological Society of...carbonate reservoir quality: Examples from Abu Dhabi and the Amu Darya Basin: Marine and Petroleum Geology, v.-15, p...

S. N. Ehrenberg; P. H. Nadeau; . Steen

4

Average Depth of Crude Oil and Natural Gas Wells  

Gasoline and Diesel Fuel Update (EIA)

Depth of Crude Oil and Natural Gas Wells Depth of Crude Oil and Natural Gas Wells (Feet per Well) Period: Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes 2003 2004 2005 2006 2007 2008 View History Exploratory and Development Wells 5,426 5,547 5,508 5,613 6,064 5,964 1949-2008 Crude Oil 4,783 4,829 4,836 4,846 5,111 5,094 1949-2008 Natural Gas 5,616 5,757 5,777 5,961 6,522 6,500 1949-2008 Dry Holes 5,744 5,848 5,405 5,382 5,578 5,540 1949-2008 Exploratory Wells 6,744 6,579 6,272 6,187 6,247 6,322 1949-2008 Crude Oil 6,950 8,136 8,011 7,448 7,537 7,778 1949-2008 Natural Gas 6,589 5,948 5,732 5,770 5,901 5,899 1949-2008 Dry Holes 6,809 6,924 6,437 6,340 6,307 6,232 1949-2008

5

Some results obtained on the study of the chemical composition of Eurasian oils depending on the depth and age of the reservoir rock  

Science Journals Connector (OSTI)

The sulfur, paraffin, resin and asphaltene contents of some 6570 Cenozoic, Mesozoic and Paleozoic Eurasian oils were analysed statistically in terms of reservoir age and depth. The database includes all principal oil-bearing basins from 60 Eurasian countries. The results of the studies of the relationships between the distribution of oils with different sulfur, paraffin, resin and asphaltene contents and the reservoir age and depth are presented. Predictive trends are established allowing polynomial predictions of average properties.

Vilori V Ahn; Yuri M Polichtchouk; Irina G Yashchenko

2002-01-01T23:59:59.000Z

6

U.S. Average Depth of Natural Gas Developmental Wells Drilled...  

Annual Energy Outlook 2012 (EIA)

Developmental Wells Drilled (Feet per Well) U.S. Average Depth of Natural Gas Developmental Wells Drilled (Feet per Well) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6...

7

U.S. Average Depth of Natural Gas Exploratory Wells Drilled ...  

Annual Energy Outlook 2012 (EIA)

Wells Drilled (Feet per Well) U.S. Average Depth of Natural Gas Exploratory Wells Drilled (Feet per Well) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8...

8

Hydrothermal Reservoirs | Open Energy Information  

Open Energy Info (EERE)

Hydrothermal Reservoirs Hydrothermal Reservoirs Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Hydrothermal Reservoirs Dictionary.png Hydrothermal Reservoir: Hydrothermal Reservoirs are underground zones of porous rock containing hot water and steam, and can be naturally occurring or human-made. Other definitions:Wikipedia Reegle Natural, shallow hydrothermal reservoirs naturally occurring hot water reservoirs, typically found at depths of less than 5 km below the Earth's surface where there is heat, water and a permeable material (permeability in rock formations results from fractures, joints, pores, etc.). Often, hydrothermal reservoirs have an overlying layer that bounds the reservoir and also serves as a thermal insulator, allowing greater heat retention. If hydrothermal reservoirs

9

Chickamauga reservoir embayment study - 1990  

SciTech Connect

The objectives of this report are three-fold: (1) assess physical, chemical, and biological conditions in the major embayments of Chickamauga Reservoir; (2) compare water quality and biological conditions of embayments with main river locations; and (3) identify any water quality concerns in the study embayments that may warrant further investigation and/or management actions. Embayments are important areas of reservoirs to be considered when assessments are made to support water quality management plans. In general, embayments, because of their smaller size (water surface areas usually less than 1000 acres), shallower morphometry (average depth usually less than 10 feet), and longer detention times (frequently a month or more), exhibit more extreme responses to pollutant loadings and changes in land use than the main river region of the reservoir. Consequently, embayments are often at greater risk of water quality impairments (e.g. nutrient enrichment, filling and siltation, excessive growths of aquatic plants, algal blooms, low dissolved oxygen concentrations, bacteriological contamination, etc.). Much of the secondary beneficial use of reservoirs occurs in embayments (viz. marinas, recreation areas, parks and beaches, residential development, etc.). Typically embayments comprise less than 20 percent of the surface area of a reservoir, but they often receive 50 percent or more of the water-oriented recreational use of the reservoir. This intensive recreational use creates a potential for adverse use impacts if poor water quality and aquatic conditions exist in an embayment.

Meinert, D.L.; Butkus, S.R.; McDonough, T.A.

1992-12-01T23:59:59.000Z

10

Geology, reservoir engineering and methane hydrate potential of the Walakpa Gas Field, North Slope, Alaska  

SciTech Connect

The Walakpa Gas Field, located near the city of Barrow on Alaska's North Slope, has been proven to be methane-bearing at depths of 2000--2550 feet below sea level. The producing formation is a laterally continuous, south-dipping, Lower Cretaceous shelf sandstone. The updip extent of the reservoir has not been determined by drilling, but probably extends to at least 1900 feet below sea level. Reservoir temperatures in the updip portion of the reservoir may be low enough to allow the presence of in situ methane hydrates. Reservoir net pay however, decreases to the north. Depths to the base of permafrost in the area average 940 feet. Drilling techniques and production configuration in the Walakpa field were designed to minimize formation damage to the reservoir sandstone and to eliminate methane hydrates formed during production. Drilling development of the Walakpa field was a sequential updip and lateral stepout from a previously drilled, structurally lower confirmation well. Reservoir temperature, pressure, and gas chemistry data from the development wells confirm that they have been drilled in the free-methane portion of the reservoir. Future studies in the Walakpa field are planned to determine whether or not a component of the methane production is due to the dissociation of updip in situ hydrates.

Glenn, R.K.; Allen, W.W.

1992-12-01T23:59:59.000Z

11

US production of natural gas from tight reservoirs  

SciTech Connect

For the purposes of this report, tight gas reservoirs are defined as those that meet the Federal Energy Regulatory Commission`s (FERC) definition of tight. They are generally characterized by an average reservoir rock permeability to gas of 0.1 millidarcy or less and, absent artificial stimulation of production, by production rates that do not exceed 5 barrels of oil per day and certain specified daily volumes of gas which increase with the depth of the reservoir. All of the statistics presented in this report pertain to wells that have been classified, from 1978 through 1991, as tight according to the FERC; i.e., they are ``legally tight`` reservoirs. Additional production from ``geologically tight`` reservoirs that have not been classified tight according to the FERC rules has been excluded. This category includes all producing wells drilled into legally designated tight gas reservoirs prior to 1978 and all producing wells drilled into physically tight gas reservoirs that have not been designated legally tight. Therefore, all gas production referenced herein is eligible for the Section 29 tax credit. Although the qualification period for the credit expired at the end of 1992, wells that were spudded (began to be drilled) between 1978 and May 1988, and from November 5, 1990, through year end 1992, are eligible for the tax credit for a subsequent period of 10 years. This report updates the EIA`s tight gas production information through 1991 and considers further the history and effect on tight gas production of the Federal Government`s regulatory and tax policy actions. It also provides some high points of the geologic background needed to understand the nature and location of low-permeability reservoirs.

Not Available

1993-10-18T23:59:59.000Z

12

Geology, reservoir engineering and methane hydrate potential of the Walakpa Gas Field, North Slope, Alaska. Final report  

SciTech Connect

The Walakpa Gas Field, located near the city of Barrow on Alaska`s North Slope, has been proven to be methane-bearing at depths of 2000--2550 feet below sea level. The producing formation is a laterally continuous, south-dipping, Lower Cretaceous shelf sandstone. The updip extent of the reservoir has not been determined by drilling, but probably extends to at least 1900 feet below sea level. Reservoir temperatures in the updip portion of the reservoir may be low enough to allow the presence of in situ methane hydrates. Reservoir net pay however, decreases to the north. Depths to the base of permafrost in the area average 940 feet. Drilling techniques and production configuration in the Walakpa field were designed to minimize formation damage to the reservoir sandstone and to eliminate methane hydrates formed during production. Drilling development of the Walakpa field was a sequential updip and lateral stepout from a previously drilled, structurally lower confirmation well. Reservoir temperature, pressure, and gas chemistry data from the development wells confirm that they have been drilled in the free-methane portion of the reservoir. Future studies in the Walakpa field are planned to determine whether or not a component of the methane production is due to the dissociation of updip in situ hydrates.

Glenn, R.K.; Allen, W.W.

1992-12-01T23:59:59.000Z

13

Determining Nighttime Atmospheric Optical Depth Using Mars Exploration Rover Images  

E-Print Network (OSTI)

was compared to the expected flux to give nighttime optical depth values. The observed nighttime optical depth was consistently similar to the daytime optical depth values on both an individual image and sol-averaged basis. Recommendations are made going...

Bean, Keri Marie

2013-07-22T23:59:59.000Z

14

Average Residential Price  

U.S. Energy Information Administration (EIA) Indexed Site

Data Series: Average Residential Price Residential Price - Local Distribution Companies Residential Price - Marketers Residential % Sold by Local Distribution Companies Average...

15

Oxygenation cost estimates for Cherokee, Douglas, and Norris reservoirs  

SciTech Connect

The capital and annual costs associated with reoxygenation of the turbine releases at Cherokee, Douglas and Norris Reservoirs using the small bubble injection technique developed for Ft. Patrick Henry Dam were computed. The weekly average dissolved oxygen (DO) deficits were computed for each reservoir for an average year (based on 16 years of records). The total annual cost of an oxygen supply and injection system for each reservoir is presented. 5 refs., 6 figs., 5 tabs.

Fain, T.G.

1980-10-01T23:59:59.000Z

16

Application of reservoir models to Cherokee Reservoir  

SciTech Connect

As a part of the Cherokee Reservoir Project hydrodynamic-temperature models and water quality models hav

Kim, B.R.; Bruggink, D.J.

1982-01-01T23:59:59.000Z

17

Frisco City sand: New Jurassic reservoir in southwest Alabama  

SciTech Connect

The first commercial production of hydrocarbons from the Jurassic Haynesville Formation in southwestern Alabama was from the Frisco City field. The field currently produces 57.8{degree} API gravity oil on 160-ac well spacing from a depth of approximately 12,000 ft. Perforations are in the Frisco City sand interval, in the lower part of the Haynesville Formation. Average porosity is 15% and average permeability is 45 md. Currently, the field has two producing wells with cumulative production of over 138,876 bbl of oil and 213,144 mcf of gas. The hydrocarbon trap in the Frisco City field is a combination structural-stratigraphic trap. The Frisco City sand reservoir is located on a faulted anticline. The stratigraphic trap is produced by a permeability barrier near the crest of the structure and termination against a basement high. The lower part of the Haynesville Formation in this area is comprised of (in ascending order) the Buckner Anhydrite Member, the Frisco City sand, and interbedded shale and anhydrite. Sandstones of the Frisco City sand interval were deposited in a shallow marine setting and have a sheetlike morphology. The sandstones are poorly to moderately sorted, angular to rounded arkose, and contain angular to rounded pebbles. The sandstones are interbedded with thin, sandy, mudstones that contribute, along with patchy carbonate and anhydrite cement, to considerable reservoir heterogeneity. Porosity is predominantly primary intergranular with a small amount of framework grain dissolution and decementation.

Mann, S.D.; Mink, R.M.; Bearden, B.L. (Geological Survey of Alabama, Tuscaloosa (USA)); Schneeflock, R.D. Jr. (Paramount Petroleum Co., Inc., Jackson, MS (USA))

1989-09-01T23:59:59.000Z

18

Full Reviews: Reservoir Characterization  

Energy.gov (U.S. Department of Energy (DOE))

Below are the project presentations and respective peer reviewer comments for Reservoir Characterization.

19

Modeling Reallocation of Reservoir Storage Capacity Between Flood Control and Conservation Purposes  

E-Print Network (OSTI)

Pattern at BRDE29 (Dennis) .................................... 284 6.4 Average Daily Flow Pattern at 515631 (Granbury Reservoir) .................. 285 6.5 Average Daily Flow Pattern at BRGR30 (Glen Rose)............................... 285... Pattern at BRDE29 (Dennis) .................................... 284 6.4 Average Daily Flow Pattern at 515631 (Granbury Reservoir) .................. 285 6.5 Average Daily Flow Pattern at BRGR30 (Glen Rose)............................... 285...

Kim, Tae Jin

2010-07-14T23:59:59.000Z

20

Unimodular Gravity and Averaging  

E-Print Network (OSTI)

The question of the averaging of inhomogeneous spacetimes in cosmology is important for the correct interpretation of cosmological data. In this paper we suggest a conceptually simpler approach to averaging in cosmology based on the averaging of scalars within unimodular gravity. As an illustration, we consider the example of an exact spherically symmetric dust model, and show that within this approach averaging introduces correlations (corrections) to the effective dynamical evolution equation in the form of a spatial curvature term.

A. Coley; J. Brannlund; J. Latta

2011-02-16T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

HFAG Charm Mixing Averages  

E-Print Network (OSTI)

Recently the first evidence for charm mixing has been reported by several experiments. To provide averages of these mixing results and other charm results, a new subgroup of the Heavy Flavor Averaging Group has been formed. We here report on the method and results of averaging the charm mixing results.

B. Aa. Petersen

2007-12-10T23:59:59.000Z

22

Petroleum reservoir porosity versus depth: Influence of geological age  

Science Journals Connector (OSTI)

...periods. The Cretaceous seems to have...Middle East Cretaceous showed that...in the Upper Jurassic sandstones...in producing Cretaceous strata of the...Bothamsall oilfield, E. Midlands...Dhabi and the Amu Darya Basin: Marine...

S. N. Ehrenberg; P. H. Nadeau; . Steen

23

Status of Cherokee Reservoir  

SciTech Connect

This is the first in a series of reports prepared by Tennessee Valley Authority (TVA) for those interested in the conditions of TVA reservoirs. This overviews of Cherokee Reservoir summarizes reservoir and watershed characteristics, reservoir uses and use impairments, water quality and aquatic biological conditions, and activities of reservoir management agencies. This information was extracted from the most current reports, publications, and data available, and interviews with water resource professionals in various Federal, state, and local agencies and in public and private water supply and wastewater treatment facilities. 11 refs., 4 figs., 1 tab.

Not Available

1990-08-01T23:59:59.000Z

24

Average Residential Price  

U.S. Energy Information Administration (EIA) Indexed Site

Pipeline and Distribution Use Price Citygate Price Residential Price Commercial Price Industrial Price Vehicle Fuel Price Electric Power Price Proved Reserves as of 12/31 Reserves Adjustments Reserves Revision Increases Reserves Revision Decreases Reserves Sales Reserves Acquisitions Reserves Extensions Reserves New Field Discoveries New Reservoir Discoveries in Old Fields Estimated Production Number of Producing Gas Wells Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production Natural Gas Processed NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals LNG Storage Additions LNG Storage Withdrawals LNG Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Lease Fuel Plant Fuel Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

25

Average Residential Price  

Gasoline and Diesel Fuel Update (EIA)

Pipeline and Distribution Use Price Citygate Price Residential Price Commercial Price Industrial Price Vehicle Fuel Price Electric Power Price Proved Reserves as of 12/31 Reserves Adjustments Reserves Revision Increases Reserves Revision Decreases Reserves Sales Reserves Acquisitions Reserves Extensions Reserves New Field Discoveries New Reservoir Discoveries in Old Fields Estimated Production Number of Producing Gas Wells Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production Natural Gas Processed NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals LNG Storage Additions LNG Storage Withdrawals LNG Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Lease Fuel Plant Fuel Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

26

Average Commercial Price  

Gasoline and Diesel Fuel Update (EIA)

Pipeline and Distribution Use Price Citygate Price Residential Price Commercial Price Industrial Price Vehicle Fuel Price Electric Power Price Proved Reserves as of 12/31 Reserves Adjustments Reserves Revision Increases Reserves Revision Decreases Reserves Sales Reserves Acquisitions Reserves Extensions Reserves New Field Discoveries New Reservoir Discoveries in Old Fields Estimated Production Number of Producing Gas Wells Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production Natural Gas Processed NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals LNG Storage Additions LNG Storage Withdrawals LNG Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Lease Fuel Plant Fuel Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

27

Layered Pseudo-Steady-State Models for tight commingled gas reservoirs  

E-Print Network (OSTI)

Fig. 5 - Typical Production Rate Performance for a Two-Layer Commingled Reservoir with constant p?& 18 Fig. 6 - Typical Average Reservoir Pressure Performance for Two-Layer Commingled Reservoirs 19 Fig. 7 - Fetkovich Decline Curves 21 Fig. 8... ? Matching Single-Layer Rate Decline With Fetkovich Curves 23 Fig. 9 - Matching a Two-Layer Commingled Reservoir With Fetkovich Curves 24 Fig. 10 - Schematic Flow Chart of the Layered PSS Program 29 Fig. 11 - Matching the Rate for Case b (Optimization...

El-Banbi, Ahmed

1995-01-01T23:59:59.000Z

28

Integrated Seismic Studies At The Rye Patch Geothermal Reservoir, Nevada |  

Open Energy Info (EERE)

Seismic Studies At The Rye Patch Geothermal Reservoir, Nevada Seismic Studies At The Rye Patch Geothermal Reservoir, Nevada Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Book: Integrated Seismic Studies At The Rye Patch Geothermal Reservoir, Nevada Details Activities (2) Areas (1) Regions (0) Abstract: A 3-D surface seismic reflection survey, covering an area of over 3 square miles, was conducted at the Rye Patch geothermal reservoir (Nevada) to explore the structural features that may control geothermal production in the area. In addition to the surface sources and receivers, a high-temperature three-component seismometer was deployed in a borehole at a depth of 3900 ft within the basement below the reservoir, which recorded the waves generated by all surface sources. A total of 1959 first-arrival travel times were determined out of 2134 possible traces. Two-dimensional

29

average | OpenEI  

Open Energy Info (EERE)

average average Dataset Summary Description This dataset is part of a larger internal dataset at the National Renewable Energy Laboratory (NREL) that explores various characteristics of large solar electric (both PV and CSP) facilities around the United States. This dataset focuses on the land use characteristics for solar facilities that are either under construction or currently in operation. Source Land-Use Requirements for Solar Power Plants in the United States Date Released June 25th, 2013 (7 months ago) Date Updated Unknown Keywords acres area average concentrating solar power csp Density electric hectares km2 land land requirements land use land-use mean photovoltaic photovoltaics PV solar statistics Data application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon Master Solar Land Use Spreadsheet (xlsx, 1.5 MiB)

30

5 - Reservoir Engineering  

Science Journals Connector (OSTI)

Publisher Summary This chapter presents the basic fundamentals that are useful to practical petroleum engineers by including basic principles, definitions, and data related to the reservoir engineering. It introduces the topics at a level that can be understood by engineers and geologists who are not expert in the field of reservoir engineering. Various correlations are provided in the chapter to understand the functioning of reservoir engineering, and newer techniques for improving recovery are also discussed. Reservoir engineering covers a broad range of subjects including the occurrence of fluids in a gas or oil-bearing reservoir, movement of those or injected fluids, and evaluation of the factors governing the recovery of oil or gas. The objectives of a reservoir engineer are to maximize producing rates and to recover oil and gas from reservoirs in the most economical manner possible. The advent of programmable calculators and personal computers has changed the approach that the reservoir engineers use to solve problems. In the chapter, many of the charts and graphs that have been historically used are presented for completeness and for illustrative purposes. In addition, separate sections of the chapter are devoted to the use of equations in some of the more common programs suitable for programmable calculators and personal computers.

F. David Martin; Robert M. Colpitts

1996-01-01T23:59:59.000Z

31

DOE Average Results  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE DOE Average Results FY 12 DOE Target FY 12 Customer Perspective: Customer Satisfaction: -Timeliness 92 88 -Quality 94 92 Effective Service Partnership: -Extent of Customer Satisfaction with the responsiveness, etc. 90 92 Internal Business Perspective: Acquisition Excellence: -Extent to which internal quality control systems are effective 90 88 Most Effective Use of Contracting Approaches to Maximize Efficiency and Cost Effectiveness: Use of Competition: -% of total $'s obligated on competitive acquisitions >$3000 (Agency Level Only) 94 85 -% of acquisition actions competed for actions > $3000 (Agency Level Only) 65 68 Performance Based Acquisition: - % PBA actions relative to total eligible new acquisition actions (applicable to new actions > $25K) 82

32

Seismicity and Reservoir Fracture Characterization  

Energy.gov (U.S. Department of Energy (DOE))

Below are the project presentations and respective peer review results for Seismicity and Reservoir Fracture Characterization.

33

Chemistry, Reservoir, and Integrated Models  

Energy.gov (U.S. Department of Energy (DOE))

Below are the project presentations and respective peer review results for Chemistry, Reservoir and Integrated Models.

34

Reservoir Protection (Oklahoma)  

Energy.gov (U.S. Department of Energy (DOE))

The Oklahoma Water Resource Board has the authority to make rules for the control of sanitation on all property located within any reservoir or drainage basin. The Board works with the Department...

35

Session: Reservoir Technology  

SciTech Connect

This session at the Geothermal Energy Program Review X: Geothermal Energy and the Utility Market consisted of five papers: ''Reservoir Technology'' by Joel L. Renner; ''LBL Research on the Geysers: Conceptual Models, Simulation and Monitoring Studies'' by Gudmundur S. Bodvarsson; ''Geothermal Geophysical Research in Electrical Methods at UURI'' by Philip E. Wannamaker; ''Optimizing Reinjection Strategy at Palinpinon, Philippines Based on Chloride Data'' by Roland N. Horne; ''TETRAD Reservoir Simulation'' by G. Michael Shook

Renner, Joel L.; Bodvarsson, Gudmundur S.; Wannamaker, Philip E.; Horne, Roland N.; Shook, G. Michael

1992-01-01T23:59:59.000Z

36

Americans' Average Radiation Exposure  

SciTech Connect

We live with radiation every day. We receive radiation exposures from cosmic rays, from outer space, from radon gas, and from other naturally radioactive elements in the earth. This is called natural background radiation. It includes the radiation we get from plants, animals, and from our own bodies. We also are exposed to man-made sources of radiation, including medical and dental treatments, television sets and emission from coal-fired power plants. Generally, radiation exposures from man-made sources are only a fraction of those received from natural sources. One exception is high exposures used by doctors to treat cancer patients. Each year in the United States, the average dose to people from natural and man-made radiation sources is about 360 millirem. A millirem is an extremely tiny amount of energy absorbed by tissues in the body.

NA

2000-08-11T23:59:59.000Z

37

Sequence stratigraphic interpretation methods for low-accommodation, alluvial depositional sequences: applications to reservoir characterization of Cut Bank field, Montana  

E-Print Network (OSTI)

laterally compartmentalize reservoir sands. Basal Sunburst sand (Sunburst 1, average net-to-gross ratio ~0.3) has better reservoir quality than other Sunburst or upper Cut Bank sands, but its reservoir quality is significantly less than that of lower Cut...

Ramazanova, Rahila

2009-05-15T23:59:59.000Z

38

Update on the Raft River Geothermal Reservoir | Open Energy Information  

Open Energy Info (EERE)

on the Raft River Geothermal Reservoir on the Raft River Geothermal Reservoir Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: Update on the Raft River Geothermal Reservoir Details Activities (1) Areas (1) Regions (0) Abstract: Since the last conference, a fourth well has been drilled to an intermediate depth and tested as a production well, with plans to use this well in the long term for injection of fluids into the strata above the production strata. The third, triple legged well has been fully pump tested, and the recovery of the second well from an injection well back to production status has revealed very interesting data on the reservoir conditions around that well. Both interference testing and geochemistry analysis shows that the third well is producing from a different aquifer

39

5 - Reservoir Engineering  

Science Journals Connector (OSTI)

Publisher Summary This chapter presents the basic fundamentals useful to practical petroleum engineers. Topics are introduced at a level that can be understood by engineers and geologists who are not expert in this field. Various correlations are provided in the chapter where useful. Newer techniques for improving recovery are also discussed in the chapter. Reservoir engineering covers a broad range of subjects including the occurrence of fluids in a gas or oil-beating reservoir, movement of those fluids or injected fluids, and evaluation of the factors governing the recovery of oil or gas. The objectives of a reservoir engineer are to maximize production rates and to ultimately recover oil and gas from reservoirs in the most economical manner possible. The chapter includes many of the charts and graphs that have been historically used. While illustrating enhanced oil recovery methods, estimation of waterflood residual oil saturation, fluid movements, material balance with volumetric analysis, the chapter also discusses pressure transient testing, recovery of hydrocarbons, and decline curve analysis. Decline curve analysis estimates primary oil recovery for an individual reservoir. The conventional analysis of production decline curves for oil or gas production consists of plotting the log of flow rate versus time on semilog paper. In case of a decline in the rate of production, the data are extrapolated into the future to provide an estimate of expected production and reserves.

2004-01-01T23:59:59.000Z

40

Dworshak Reservoir Kokanee Population Monitoring, Annual Report 2001.  

SciTech Connect

Onsite testing of strobe lights was conducted to determine if they repelled kokanee Oncorhynchus nerka away from the turbine intakes at Dworshak Dam. We tested a set of nine strobe lights flashing at a rate of 360 flashes/min placed near the intake of a 90 mW turbine. A split-beam echo sounder was used to determine the effect of strobe light operation on fish density (thought to be mostly kokanee) in front of the turbine intakes. On five nights between December 2001 and January 2002, fish density averaged 110 fish/ha when no lights were flashing. Mean density dropped to 13 fish/ha when the strobe lights were turned on during five additional nights of sampling. This 88% decline in density was significant at the P = 0.009 level of significance based on a paired Student's t test. There appeared to be no tendency for fish to habituate to the lights during the night. Test results indicate that a single set of nine lights may be sufficient to repel kokanee from a turbine intake during the night. We also used split-beam hydroacoustics to monitor the kokanee population in Dworshak Reservoir during 2001. Estimated abundance of kokanee has continued to increase since the spring of 1996 when high entrainment losses occurred. Based on hydroacoustic surveys, we estimated 3,276,000 kokanee in Dworshak Reservoir in early July 2001. This included 2,069,000 age-0 kokanee (90% CI {+-} 16.4%), 801,000 age-1 kokanee (90% CI {+-} 17.8%), and 406,000 age-2 kokanee (90% CI {+-} 20.5%). Entrainment sampling was also conducted with split-beam hydroacoustics a minimum of one continuous 24 h period per month. The highest entrainment rates occurred at night with lower discharges and shallower intake depths. Fish movement patterns suggested that they swam 'at will' in front of the intakes and may have chosen to move into the turbine intakes. Based on monthly hydroacoustic sampling in the forebay, we found that kokanee density was low in July and August during a period of high discharge. However, kokanee density was high in late winter when discharge was also high, thus increasing the likelihood of entrainment. Counts of spawning kokanee in four tributary streams used as an index reached 6,079 fish. This spawner count appeared unusually low considering the high population estimate of kokanee in the reservoir and data collected in previous years.

Maiolie, Melo; Stark, Eric

2003-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Optoelectronic Reservoir Computing  

E-Print Network (OSTI)

Reservoir computing is a recently introduced, highly efficient bio-inspired approach for processing time dependent data. The basic scheme of reservoir computing consists of a non linear recurrent dynamical system coupled to a single input layer and a single output layer. Within these constraints many implementations are possible. Here we report an opto-electronic implementation of reservoir computing based on a recently proposed architecture consisting of a single non linear node and a delay line. Our implementation is sufficiently fast for real time information processing. We illustrate its performance on tasks of practical importance such as nonlinear channel equalization and speech recognition, and obtain results comparable to state of the art digital implementations.

Yvan Paquot; Franois Duport; Anteo Smerieri; Joni Dambre; Benjamin Schrauwen; Marc Haelterman; Serge Massar

2011-11-30T23:59:59.000Z

42

Reviving Abandoned Reservoirs with High-Pressure Air Injection: Application in a Fractured and Karsted Dolomite Reservoir  

SciTech Connect

Despite declining production rates, existing reservoirs in the United States contain vast volumes of remaining oil that is not being effectively recovered. This oil resource constitutes a huge target for the development and application of modern, cost-effective technologies for producing oil. Chief among the barriers to the recovery of this oil are the high costs of designing and implementing conventional advanced recovery technologies in these mature, in many cases pressure-depleted, reservoirs. An additional, increasingly significant barrier is the lack of vital technical expertise necessary for the application of these technologies. This lack of expertise is especially notable among the small operators and independents that operate many of these mature, yet oil-rich, reservoirs. We addressed these barriers to more effective oil recovery by developing, testing, applying, and documenting an innovative technology that can be used by even the smallest operator to significantly increase the flow of oil from mature U.S. reservoirs. The Bureau of Economic Geology and Goldrus Producing Company assembled a multidisciplinary team of geoscientists and engineers to evaluate the applicability of high-pressure air injection (HPAI) in revitalizing a nearly abandoned carbonate reservoir in the Permian Basin of West Texas. The Permian Basin, the largest oil-bearing basin in North America, contains more than 70 billion barrels of remaining oil in place and is an ideal venue to validate this technology. We have demonstrated the potential of HPAI for oil-recovery improvement in preliminary laboratory tests and a reservoir pilot project. To more completely test the technology, this project emphasized detailed characterization of reservoir properties, which were integrated to access the effectiveness and economics of HPAI. The characterization phase of the project utilized geoscientists and petroleum engineers from the Bureau of Economic Geology and the Department of Petroleum Engineering (both at The University of Texas at Austin) to define the controls on fluid flow in the reservoir as a basis for developing a reservoir model. The successful development of HPAI technology has tremendous potential for increasing the flow of oil from deep carbonate reservoirs in the Permian Basin, a target resource that can be conservatively estimated at more than 1.5 billion barrels. Successful implementation in the field chosen for demonstration, for example, could result in the recovery of more than 34 million barrels of oil that will not otherwise be produced. Geological and petrophysical analysis of available data at Barnhart field reveals the following important observations: (1) the Barnhart Ellenburger reservoir is similar to most other Ellenburger reservoirs in terms of depositional facies, diagenesis, and petrophysical attributes; (2) the reservoir is characterized by low to moderate matrix porosity much like most other Ellenburger reservoirs in the Permian Basin; (3) karst processes (cave formation, infill, and collapse) have substantially altered stratigraphic architecture and reservoir properties; (4) porosity and permeability increase with depth and may be associated with the degree of karst-related diagenesis; (5) tectonic fractures overprint the reservoir, improving overall connectivity; (6) oil-saturation profiles show that the oil-water contact (OWC) is as much as 125 ft lower than previous estimations; (7) production history and trends suggest that this reservoir is very similar to other solution-gas-drive reservoirs in the Permian Basin; and (8) reservoir simulation study showed that the Barnhart reservoir is a good candidate for HPAI and that application of horizontal-well technology can improve ultimate resource recovery from the reservoir.

Robert Loucks; Stephen C. Ruppel; Dembla Dhiraj; Julia Gale; Jon Holder; Jeff Kane; Jon Olson; John A. Jackson; Katherine G. Jackson

2006-09-30T23:59:59.000Z

43

Reservoir geochemistry: A link between reservoir geology and engineering?  

SciTech Connect

Geochemistry provides a natural, but poorly exploited, link between reservoir geology and engineering. The authors summarize some current applications of geochemistry to reservoir description and stress that, because of their strong interactions with mineral surfaces and water, nitrogen and oxygen compounds in petroleum may exert an important influence on the pressure/volume/temperature (PVT) properties of petroleum, viscosity and wettability. The distribution of these compounds in reservoirs is heterogeneous on a submeter scale and is partly controlled by variations in reservoir quality. The implied variations in petroleum properties and wettability may account for some of the errors in reservoir simulations.

Larter, S.R.; Aplin, A.C.; Chen, M.; Taylor, P.N. [Univ. of Newcastle (Australia); Corbett, P.W.M.; Ementon, N. [Heriot-Watt Univ., Edinburgh (United Kingdom)

1997-02-01T23:59:59.000Z

44

Variable depth core sampler  

DOE Patents (OSTI)

A variable depth core sampler apparatus comprising a first circular hole saw member, having longitudinal sections that collapses to form a point and capture a sample, and a second circular hole saw member residing inside said first hole saw member to support the longitudinal sections of said first hole saw member and prevent them from collapsing to form a point. The second hole saw member may be raised and lowered inside said first hole saw member.

Bourgeois, Peter M. (Hamburg, NY); Reger, Robert J. (Grand Island, NY)

1996-01-01T23:59:59.000Z

45

Variable depth core sampler  

DOE Patents (OSTI)

A variable depth core sampler apparatus is described comprising a first circular hole saw member, having longitudinal sections that collapses to form a point and capture a sample, and a second circular hole saw member residing inside said first hole saw member to support the longitudinal sections of said first hole saw member and prevent them from collapsing to form a point. The second hole saw member may be raised and lowered inside said first hole saw member. 7 figs.

Bourgeois, P.M.; Reger, R.J.

1996-02-20T23:59:59.000Z

46

Reservoir characterization of thinly laminated heterolithic facies within shallow-marine sand bodies  

SciTech Connect

Shallow marine sandstones typically form high quality reservoirs but they can contain a significant proportion of extremely heterogeneous facies. Particularly significant are heterolithic (mixed interlaminated sand-mud) deposits which are common in estuarine/incised valley-fill reservoirs and other tidally-influenced depositional environments. The complex mm/cm-scale interfingering of sands and clays in these reservoirs is below the resolution of most logging tools, which poses major problems for the petrophysical evaluation, quantitative reservoir modelling and reservoir performance prediction. This study outlines an integrated geological/petrophysical framework for the reservoir characterization of heterolithic facies from the Jurassic of the North Sea Basin which utilizes well logs, cores, minipermeameter and analog outcrop data. The calibration of wireline logs (GR, LDT/CNL, EPT and dipmeter) with cores helps in establishing the relationship between the architecture of sand-shale laminations and their wireline log response/electrofacies. The routine sampling procedure for porosity/permeability measurement from cores will not accurately determine the average reservoir properties for these heterolithic intervals. The selection of measurement points is of vital importance for determining average reservoir properties. The minipermeameter measurements are especially useful for these thin bedded reservoirs and serve as a useful guide for reservoir zonation and evaluation of petrophysical properties from wireline logs. The incorporation of analog outcrop data helps further in establishing vertical and lateral communication relationships at field scale.

Gupta, R.; Johnson, H. [Imperial College, London (United Kingdom); Myking, B.

1996-08-01T23:59:59.000Z

47

Viscosity-average molecular weight  

Science Journals Connector (OSTI)

n .... An averaged molecular weight for high polymers that relates most closely to measurements of dilute-solution viscosities ...

2007-01-01T23:59:59.000Z

48

Reservoir Stimulation Optimization with Operational Monitoring for Creation of EGS  

SciTech Connect

EGS field projects have not sustained production at rates greater than of what is needed for economic viability. The primary limitation that makes commercial EGS infeasible is our current inability to cost-effectively create high-permeability reservoirs from impermeable, igneous rock within the 3,000-10,000 ft depth range. Our goal is to develop a novel fracturing fluid technology that maximizes reservoir permeability while reducing stimulation cost and environmental impact. Laboratory equipment development to advance laboratory characterization/monitoring is also a priority of this project to study and optimize the physicochemical properties of these fracturing fluids in a range of reservoir conditions. Barrier G is the primarily intended GTO barrier to be addressed as well as support addressing barriers D, E and I.

Carlos A. Fernandez

2013-09-25T23:59:59.000Z

49

NOTES ON NEUTRON DEPTH PROFILING  

E-Print Network (OSTI)

NOTES ON NEUTRON DEPTH PROFILING by J.K. Shultis Department of Mechanical and Nuclear Engineering College of Engineering Kansas State University Manhattan, Kansas 66506 Dec. 2003 #12;Notes on Neutron Depth Profiling J. Kenneth Shultis December 2003 1 Introduction The purpose of neutron depth profiling

Shultis, J. Kenneth

50

Averaging Hypotheses in Newtonian Cosmology  

E-Print Network (OSTI)

Average properties of general inhomogeneous cosmological models are discussed in the Newtonian framework. It is shown under which circumstances the average flow reduces to a member of the standard Friedmann--Lema\\^\\i tre cosmologies. Possible choices of global boundary conditions of inhomogeneous cosmologies as well as consequences for the interpretation of cosmological parameters are put into perspective.

T. Buchert

1995-12-20T23:59:59.000Z

51

Oil composition variation and reservoir continuity: Unity field, Sudan  

Science Journals Connector (OSTI)

A suite of oils from stacked reservoirs in the Unity Field in Sudan has been analyzed by various geochemical techniques for molecular information to elucidate the geological processes which cause variations in oil composition and their resulting oil fingerprints in different reservoir units. Analyses of these highly paraffinic oils indicate that the chromatographic fingerprint variations are due to differences in the abundances of saturated compounds, including branched and cyclic alkanes. Neither aromatics nor NSO compounds have any significant effect on the observed fingerprint variations. This association of saturates, instead of aromatics and NSO compounds, with the fingerprint variations precludes rock-fluid interactions as a cause of the variations. Biomarker analyses show that variations in thermal maturity and organic facies of the source rock are responsible for the fingerprint variations. Thermal maturity increases with the depth of the reservoir, suggesting a multiple-charge process for the oils to fill these reservoirs over an extended period of time. Apparently the source rock generated and expelled progressively more mature oils and little mixing occurred during migration. Thus, knowledge of oil compositional variations from one reservoir to another, organic facies variation and source rock maturity combined with tectonic history may help explain charging and timing of oil emplacement.

R.J. Hwang; A.S. Ahmed; J.M. Moldowan

1994-01-01T23:59:59.000Z

52

US Geological Survey publications on western tight gas reservoirs  

SciTech Connect

This bibliography includes reports published from 1977 through August 1988. In 1977 the US Geological Survey (USGS), in cooperation with the US Department of Energy's, (DOE), Western Gas Sands Research program, initiated a geological program to identify and characterize natural gas resources in low-permeability (tight) reservoirs in the Rocky Mountain region. These reservoirs are present at depths of less than 2,000 ft (610 m) to greater than 20,000 ft (6,100 m). Only published reports readily available to the public are included in this report. Where appropriate, USGS researchers have incorporated administrative report information into later published studies. These studies cover a broad range of research from basic research on gas origin and migration to applied studies of production potential of reservoirs in individual wells. The early research included construction of regional well-log cross sections. These sections provide a basic stratigraphic framework for individual areas and basins. Most of these sections include drill-stem test and other well-test data so that the gas-bearing reservoirs can be seen in vertical and areal dimensions. For the convenience of the reader, the publications listed in this report have been indexed by general categories of (1) authors, (2) states, (3) geologic basins, (4) cross sections, (5) maps (6) studies of gas origin and migration, (7) reservoir or mineralogic studies, and (8) other reports of a regional or specific topical nature.

Krupa, M.P.; Spencer, C.W.

1989-02-01T23:59:59.000Z

53

Data requirements and acquisition for reservoir characterization  

SciTech Connect

This report outlines the types of data, data sources and measurement tools required for effective reservoir characterization, the data required for specific enhanced oil recovery (EOR) processes, and a discussion on the determination of the optimum data density for reservoir characterization and reservoir modeling. The two basic sources of data for reservoir characterization are data from the specific reservoir and data from analog reservoirs, outcrops, and modern environments. Reservoir data can be divided into three broad categories: (1) rock properties (the container) and (2) fluid properties (the contents) and (3)interaction between reservoir rock and fluid. Both static and dynamic measurements are required.

Jackson, S.; Chang, Ming Ming; Tham, Min.

1993-03-01T23:59:59.000Z

54

Peer Reviewed: Experimenting with Hydroelectric Reservoirs  

Science Journals Connector (OSTI)

Peer Reviewed: Experimenting with Hydroelectric Reservoirs ... Researchers created reservoirs in Canada to explore the impacts of hydroelectric developments on greenhouse gas and methylmercury production. ...

R. A. Bodaly; Kenneth G. Beaty; Len H. Hendzel; Andrew R. Majewski; Michael J. Paterson; Kristofer R. Rolfhus; Alan F. Penn; Vincent L. St. Louis; Britt D. Hall; Cory J. D. Matthews; Katharine A. Cherewyk; Mariah Mailman; James P. Hurley; Sherry L. Schiff; Jason J. Venkiteswaran

2004-09-15T23:59:59.000Z

55

Oil and Gas CDT Predicting fault permeability at depth: incorporating natural  

E-Print Network (OSTI)

Oil and Gas CDT Predicting fault permeability at depth: incorporating natural permeability controls on fluid flow in oil and gas reservoirs. Fault zones are composed of many deformation elements will receive 20 weeks bespoke, residential training of broad relevance to the oil and gas industry: 10 weeks

Henderson, Gideon

56

FRACTURED PETROLEUM RESERVOIRS  

SciTech Connect

The four chapters that are described in this report cover a variety of subjects that not only give insight into the understanding of multiphase flow in fractured porous media, but they provide also major contribution towards the understanding of flow processes with in-situ phase formation. In the following, a summary of all the chapters will be provided. Chapter I addresses issues related to water injection in water-wet fractured porous media. There are two parts in this chapter. Part I covers extensive set of measurements for water injection in water-wet fractured porous media. Both single matrix block and multiple matrix blocks tests are covered. There are two major findings from these experiments: (1) co-current imbibition can be more efficient than counter-current imbibition due to lower residual oil saturation and higher oil mobility, and (2) tight fractured porous media can be more efficient than a permeable porous media when subjected to water injection. These findings are directly related to the type of tests one can perform in the laboratory and to decide on the fate of water injection in fractured reservoirs. Part II of Chapter I presents modeling of water injection in water-wet fractured media by modifying the Buckley-Leverett Theory. A major element of the new model is the multiplication of the transfer flux by the fractured saturation with a power of 1/2. This simple model can account for both co-current and counter-current imbibition and computationally it is very efficient. It can be orders of magnitude faster than a conventional dual-porosity model. Part II also presents the results of water injection tests in very tight rocks of some 0.01 md permeability. Oil recovery from water imbibition tests from such at tight rock can be as high as 25 percent. Chapter II discusses solution gas-drive for cold production from heavy-oil reservoirs. The impetus for this work is the study of new gas phase formation from in-situ process which can be significantly different from that of gas displacement processes. The work is of experimental nature and clarifies several misconceptions in the literature. Based on experimental results, it is established that the main reason for high efficiency of solution gas drive from heavy oil reservoirs is due to low gas mobility. Chapter III presents the concept of the alteration of porous media wettability from liquid-wetting to intermediate gas-wetting. The idea is novel and has not been introduced in the petroleum literature before. There are significant implications from such as proposal. The most direct application of intermediate gas wetting is wettability alteration around the wellbore. Such an alteration can significantly improve well deliverability in gas condensate reservoirs where gas well deliverability decreases below dewpoint pressure. Part I of Chapter III studies the effect of gravity, viscous forces, interfacial tension, and wettability on the critical condensate saturation and relative permeability of gas condensate systems. A simple phenomenological network model is used for this study, The theoretical results reveal that wettability significantly affects both the critical gas saturation and gas relative permeability. Gas relative permeability may increase ten times as contact angle is altered from 0{sup o} (strongly liquid wet) to 85{sup o} (intermediate gas-wetting). The results from the theoretical study motivated the experimental investigation described in Part II. In Part II we demonstrate that the wettability of porous media can be altered from liquid-wetting to gas-wetting. This part describes our attempt to find appropriate chemicals for wettability alteration of various substrates including rock matrix. Chapter IV provides a comprehensive treatment of molecular, pressure, and thermal diffusion and convection in porous media Basic theoretical analysis is presented using irreversible thermodynamics.

Abbas Firoozabadi

1999-06-11T23:59:59.000Z

57

TEXAS A&M UNIVERSITY Reservoir Geophysics Program  

E-Print Network (OSTI)

includes applications to clastic reservoirs, heavy oil reservoirs, gas/oil shale, gas hydrates. Basic

58

Analysis of real-time reservoir monitoring : reservoirs, strategies, & modeling.  

SciTech Connect

The project objective was to detail better ways to assess and exploit intelligent oil and gas field information through improved modeling, sensor technology, and process control to increase ultimate recovery of domestic hydrocarbons. To meet this objective we investigated the use of permanent downhole sensors systems (Smart Wells) whose data is fed real-time into computational reservoir models that are integrated with optimized production control systems. The project utilized a three-pronged approach (1) a value of information analysis to address the economic advantages, (2) reservoir simulation modeling and control optimization to prove the capability, and (3) evaluation of new generation sensor packaging to survive the borehole environment for long periods of time. The Value of Information (VOI) decision tree method was developed and used to assess the economic advantage of using the proposed technology; the VOI demonstrated the increased subsurface resolution through additional sensor data. Our findings show that the VOI studies are a practical means of ascertaining the value associated with a technology, in this case application of sensors to production. The procedure acknowledges the uncertainty in predictions but nevertheless assigns monetary value to the predictions. The best aspect of the procedure is that it builds consensus within interdisciplinary teams The reservoir simulation and modeling aspect of the project was developed to show the capability of exploiting sensor information both for reservoir characterization and to optimize control of the production system. Our findings indicate history matching is improved as more information is added to the objective function, clearly indicating that sensor information can help in reducing the uncertainty associated with reservoir characterization. Additional findings and approaches used are described in detail within the report. The next generation sensors aspect of the project evaluated sensors and packaging survivability issues. Our findings indicate that packaging represents the most significant technical challenge associated with application of sensors in the downhole environment for long periods (5+ years) of time. These issues are described in detail within the report. The impact of successful reservoir monitoring programs and coincident improved reservoir management is measured by the production of additional oil and gas volumes from existing reservoirs, revitalization of nearly depleted reservoirs, possible re-establishment of already abandoned reservoirs, and improved economics for all cases. Smart Well monitoring provides the means to understand how a reservoir process is developing and to provide active reservoir management. At the same time it also provides data for developing high-fidelity simulation models. This work has been a joint effort with Sandia National Laboratories and UT-Austin's Bureau of Economic Geology, Department of Petroleum and Geosystems Engineering, and the Institute of Computational and Engineering Mathematics.

Mani, Seethambal S.; van Bloemen Waanders, Bart Gustaaf; Cooper, Scott Patrick; Jakaboski, Blake Elaine; Normann, Randy Allen; Jennings, Jim (University of Texas at Austin, Austin, TX); Gilbert, Bob (University of Texas at Austin, Austin, TX); Lake, Larry W. (University of Texas at Austin, Austin, TX); Weiss, Chester Joseph; Lorenz, John Clay; Elbring, Gregory Jay; Wheeler, Mary Fanett (University of Texas at Austin, Austin, TX); Thomas, Sunil G. (University of Texas at Austin, Austin, TX); Rightley, Michael J.; Rodriguez, Adolfo (University of Texas at Austin, Austin, TX); Klie, Hector (University of Texas at Austin, Austin, TX); Banchs, Rafael (University of Texas at Austin, Austin, TX); Nunez, Emilio J. (University of Texas at Austin, Austin, TX); Jablonowski, Chris (University of Texas at Austin, Austin, TX)

2006-11-01T23:59:59.000Z

59

Characterization Of Fracture Patterns In The Geysers Geothermal Reservoir  

Open Energy Info (EERE)

Patterns In The Geysers Geothermal Reservoir Patterns In The Geysers Geothermal Reservoir By Shear-Wave Splitting Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report: Characterization Of Fracture Patterns In The Geysers Geothermal Reservoir By Shear-Wave Splitting Details Activities (1) Areas (1) Regions (0) Abstract: The authors have analyzed the splitting of shear waves from microearthquakes recorded by a 16-station three-component seismic network at the Northwest Geysers geothermal field, Geysers, California, to determine the preferred orientation of subsurface fractures and cracks. Average polarization crack directions with standard deviation were computed for each station. Also, graphical fracture characterizations in the form of equal-area projections and rose diagrams were created to depict the

60

MAPPING OF RESERVOIR PROPERTIES AND FACIES THROUGH INTEGRATION OF STATIC AND DYNAMIC DATA  

SciTech Connect

Knowledge of the distribution of permeability and porosity in a reservoir is necessary for the prediction of future oil production, estimation of the location of bypassed oil, and optimization of reservoir management. But while the volume of data that can potentially provide information on reservoir architecture and fluid distributions has increased enormously in the past decade, it is not yet possible to make use of all the available data in an integrated fashion. While it is relatively easy to generate plausible reservoir models that honor static data such as core, log, and seismic data, it is far more difficult to generate plausible reservoir models that honor dynamic data such as transient pressures, saturations, and flow rates. As a result, the uncertainty in reservoir properties is higher than it could be and reservoir management can not be optimized. The goal of this project is to develop computationally efficient automatic history matching techniques for generating geologically plausible reservoir models which honor both static and dynamic data. Solution of this problem is necessary for the quantification of uncertainty in future reservoir performance predictions and for the optimization of reservoir management. Facies (defined here as regions of relatively uniform petrophysical properties) are common features of all reservoirs. Because the flow properties of the various facies can vary greatly, knowledge of the location of facies boundaries is of utmost importance for the prediction of reservoir performance and for the optimization of reservoir management. When the boundaries between facies are fairly well known, but flow properties are poorly known, the average properties for all facies can be determined using traditional techniques. Traditional history matching honors dynamic data by adjusting petrophysical properties in large areas, but in the process of adjusting the reservoir model ignores the static data and often results in implausible reservoir models. In general, boundary locations, average permeability and porosity, relative permeability curves, and local flow properties may all need to be adjusted to achieve a plausible reservoir model that honors all data. In this project, we will characterize the distribution of geologic facies as an indicator random field, making use of the tools of geostatistics as well as the tools of inverse and probability theory for data integration.

Albert C. Reynolds; Dean S. Oliver; Fengjun Zhang; Yannong Dong; Jan Arild Skjervheim; Ning Liu

2003-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Core Measure Average KTR Results  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Measure Measure Average KTR Results FY 12 Target FY 12 DOE M&O CONTRACTOR (KTR) BSC RESULTS FY 2012 Customer Perspective and level of communication provided by the procurement office 95 92 Internal Business Perspective: Assessment (%) of the degree to which the purchasing system is in compliance with stakeholder requirements 97 Local Goals % Delivery on-time (includes JIT, excludes Purchase Cards) 88 84 % of total dollars obligated, on actions > $150K , that were awarded using effective competition 73 Local Goals Rapid Purchasing Techniques: -% of transactions placed by users 77 Local Goals -% of transactions placed through electronic commerce 62 Local Goals Average Cycle Time: -Average cycle time for <= $150K 8 6 to 9 days

62

Influence of depositional sand quality and diagenesis on porosity and permeability: Examples from Brent Group reservoirs, northern North Sea  

SciTech Connect

Multivariate statistical analysis was applied to examine correlations between reservoir quality and petrology in two data sets from the Middle Jurassic Brent Group. One of the data sets is from relatively shallow depth and has been little affected by chemical diagenesis (Statfjord Nord and Ost Fields; 2.3--2.6 km below the sea floor), while the second data set is from a more deeply buried reservoir having an advanced degree of diagenesis (Huldra Field; 3.6--3.9 km). Much of the total variation in porosity and permeability within each data set (0.02 mD to > 7 D in both sets) can be accounted for by laboratory measurements of parameters mainly related to depositional sand quality, including shaliness (represented by bulk-rock alumina/silica ratio), early carbonate cement, feldspar content, and grain size. Despite major differences in the proportions of different sedimentary facies in the two data sets, they have similar ranges of depositional sand quality and therefore probably had similar reservoir quality early in their burial history. Deeper burial diagenesis at Huldra Field has shifted the average of both porosity and permeability to lower values and produced a bimodal permeability distribution, apparently reflecting preferential preservation of permeability in the cleaner sandstones. On the basis of these examples, the author outlines an approach for unmixing the diagenetic and lithologic components of variation in regional compilations of sandstone porosity-permeability data. The procedure and its consequences are illustrated using a regional compilation of core data from the Brent Group of the northern North Sea.

Ehrenberg, S.N. [Statoil, Harstad (Norway)

1997-01-01T23:59:59.000Z

63

Influence of depositional sand quality of porosity and permeability: Examples from Brent Group Reservoirs in the northern North Sea  

SciTech Connect

Multivariate statistical analysis was applied to examine correlation between reservoir quality and petrology in two data sets from the Middle Jurassic Brent Group. One of the data sets is from relatively shallow depth an has been little affected by chemical diagenesis (Staffjord Nord & Ost Fields 2.3-2.6 km below the sea floor), while the second data set is from a more deeply buried reservoir having an advanced degree of diagenesis (Huldra Field 3.6-3.9 km). Much of the total variation in porosity and permeability (0.02 mD to >7 D in both sets) can be accounted for by laboratory measurements of parameters mainly related to depositional sand quality, including {open_quotes}shaliness{close_quotes} (represented by bulk-rock alumina content), earl carbonate cement, feldspar content, and grain size. Despite major differences in the proportions of different sedimentary facies in the two data sets, they have similar ranges of depositional sand quality and therefore probably had similar reservoir quality early in their burial history. Deeper burial diagenesis at Huldra Field has shifted the average porosity and permeability lower and produced a bimodal permeability distribution, apparently reflecting preferential preservation of permeability in the cleaner sandstones. Based on these examples, a method is outlined for {open_quotes}unmixing{close_quotes} the diagenetic and lithologic components of variation in regional compilations of sandstone porosity-permeability data. The procedure and its consequences are illustrated using a regional compilation of core data from the Brent Group of northern North Sea.

Ehrenberg, S.N.; Bjorkum, P.A.; Naddeau, P.H. [Statoil, Stavanger (Norway)

1996-12-31T23:59:59.000Z

64

West Texas Intermediate Spot Average ............................  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil (dollars per barrel) Crude Oil (dollars per barrel) West Texas Intermediate Spot Average ............................ 102.88 93.42 92.24 87.96 94.34 94.10 105.84 96.30 95.67 95.33 95.67 93.33 94.12 97.64 95.00 Brent Spot Average ........................................................... 118.49 108.42 109.61 110.09 112.49 102.58 110.27 108.29 106.33 105.00 103.00 102.00 111.65 108.41 104.08 Imported Average .............................................................. 108.14 101.18 97.18 97.64 98.71 97.39 103.07 100.03 99.64 99.33 99.69 97.35 101.09 99.85 99.04 Refiner Average Acquisition Cost ...................................... 107.61 101.44 97.38 97.27 101.14 99.45 105.24 100.44 100.15 99.82 100.18 97.83 100.83 101.61 99.50 Liquid Fuels (cents per gallon) Refiner Prices for Resale Gasoline .........................................................................

65

Reservoir characteristics of Lower Wilcox Sandstones, Lobo Trend, Webb and Zapata Counties, Texas  

SciTech Connect

To date, over 340 bcf of gas have been produced from the Lobo sandstones in the Laredo field area at depths of less than 10,000 ft (3050 m). Gas accumulation is controlled by faulting and erosional truncation. The resulting structural complexity has made accurate prediction of reservoir sandstones difficult. Cored sections display repetitive ordered sequences of sedimentary structures and textural and compositional gradations indicative of turbidity-current deposits. The reservoir sandstones were deposited as constructional channels having vertical and lateral variation from channel-fill to channel-margin to overbank deposits. Channel-fill units are 2-10 ft (0.61-3.05 m) thick and composed of AB, AE, and ABE bedsets. Channel-margin units are 1-3 ft (0.31-0.92 m) thick and contain thinner, more complete ABC, ABE and ABCE sequences. Overbank deposits consist of highly bioturbated, thinly interbedded sandstones and shales. Sandstones are feldspathic litharenites that have 15% matrix and 15% calcite cement. Porosities average 16% and permeabilities range from 0.54 to 12 md, decreasing with increased matrix, cement, and bioturbation. The channel-fill sandstones are linear, dip-trending bodies less than 3000 ft (915 m) wide, which bifurcate downdip into distributary channels. High-intensity, small-scale, soft-sediment deformation indicates the sandstones were deposited in an unstable outer-shelf to upper-slope environment. A slumped, dip-trending channel-fill interpretation for the Lobo sandstones provides a mechanism for sediment transport beyond the present downdip limits of the trend.

Henke, K.A.

1985-02-01T23:59:59.000Z

66

Reservoir characterization of Pennsylvanian Sandstone Reservoirs. Annual report  

SciTech Connect

This annual report describes the progress during the second year of a project on Reservoir Characterization of Pennsylvanian Sandstone Reservoirs. The report is divided into three sections: (i) reservoir description and scale-up procedures; (ii) outcrop investigation; (iii) in-fill drilling potential. The first section describes the methods by which a reservoir can be characterized, can be described in three dimensions, and can be scaled up with respect to its properties, appropriate for simulation purposes. The second section describes the progress on investigation of an outcrop. The outcrop is an analog of Bartlesville Sandstone. We have drilled ten wells behind the outcrop and collected extensive log and core data. The cores have been slabbed, photographed and the several plugs have been taken. In addition, minipermeameter is used to measure permeabilities on the core surface at six inch intervals. The plugs have been analyzed for the permeability and porosity values. The variations in property values will be tied to the geological descriptions as well as the subsurface data collected from the Glen Pool field. The third section discusses the application of geostatistical techniques to infer in-fill well locations. The geostatistical technique used is the simulated annealing technique because of its flexibility. One of the important reservoir data is the production data. Use of production data will allow us to define the reservoir continuities, which may in turn, determine the in-fill well locations. The proposed technique allows us to incorporate some of the production data as constraints in the reservoir descriptions. The technique has been validated by comparing the results with numerical simulations.

Kelkar, M.

1992-09-01T23:59:59.000Z

67

Mapping Indigenous Depth of Place  

E-Print Network (OSTI)

AMERICAN INDIAN CULTURE AND RESEARCH JOURNAL 32:3 (2008) 107126 107 Mapping Indigenous Depth of Place MARGARET WICKENS PEARCE AND RENEE PUALANI LOUIS INTRODUCTION Indigenous communities have successfully used Western geospatial technolo- gies (GT... of geog- raphy at Ohio University in Athens, Ohio. Renee Pualani Louis is Hawaiian and recently completed her doctorate in geography at the University of Hawaii at Manoa, Honolulu, Hawaii. Published as M. Pearce and R. Louis. Mapping Indigenous depth...

Pearce, Margaret Wickens; Louis, Renee Pualani

2008-11-01T23:59:59.000Z

68

Analysis of microearthquake data at Cold Lake and its applications to reservoir monitoring  

E-Print Network (OSTI)

-difference method, which highlights several tight event clusters. The deep cluster at a depth of 400 m, just above the oil reservoir, shows very high seismicity during the CSS processes.Asec- ond cluster is observed of the region. We analyzed a microearthquake data set from Cold Lake,Alberta, where heavy oil is extracted using

Snieder, Roel

69

Hydraulic fracturing in a sedimentary geothermal reservoir: Results and implications  

Science Journals Connector (OSTI)

Field experiments in a geothermal research well were conducted to enhance the inflow performance of a clastic sedimentary reservoir section. Due to depths exceeding 4050m, bottom hole temperatures exceeding 140C, and open hole section (dual zone), technically demanding and somewhat unprecedented conditions had to be managed. The fracturing operations were successful. Fractures were created in two isolated borehole intervals and the inflow behaviour of the reservoir was decisively enhanced. The effective pressures applied for fracture initiation and propagation were only slightly above in situ pore pressures. Nevertheless, the stimulation ratio predicted by fracture performance modelling could not be achieved. Multiple reasons could be identified that account for the mismatch. An insufficient fracture tie-back, as well as chemical and mechanical processes during closure, led to reduced fracture conductivities and therefore diminished productivity. The insights gained are the basis for further fracture design concepts at the given and geologic comparable sites.

B. Legarth; E. Huenges; G. Zimmermann

2005-01-01T23:59:59.000Z

70

Variable Average Absolute Percent Differences  

U.S. Energy Information Administration (EIA) Indexed Site

Variable Variable Average Absolute Percent Differences Percent of Projections Over- Estimated Gross Domestic Product Real Gross Domestic Product (Average Cumulative Growth)* (Table 2) 1.0 42.6 Petroleum Imported Refiner Acquisition Cost of Crude Oil (Constant $) (Table 3a) 35.2 18.6 Imported Refiner Acquisition Cost of Crude Oil (Nominal $) (Table 3b) 34.7 19.7 Total Petroleum Consumption (Table 4) 6.2 66.5 Crude Oil Production (Table 5) 6.0 59.6 Petroleum Net Imports (Table 6) 13.3 67.0 Natural Gas Natural Gas Wellhead Prices (Constant $) (Table 7a) 30.7 26.1 Natural Gas Wellhead Prices (Nominal $) (Table 7b) 30.0 27.1 Total Natural Gas Consumption (Table 8) 7.8 70.2 Natural Gas Production (Table 9) 7.1 66.0 Natural Gas Net Imports (Table 10) 29.3 69.7 Coal Coal Prices to Electric Generating Plants (Constant $)** (Table 11a)

71

THMC Modeling of EGS Reservoirs ? Continuum through Discontinuum Representations: Capturing Reservoir Stimulation, Evolution and Induced Seismicity  

Energy.gov (U.S. Department of Energy (DOE))

THMC Modeling of EGS Reservoirs ? Continuum through Discontinuum Representations: Capturing Reservoir Stimulation, Evolution and Induced Seismicity presentation at the April 2013 peer review meeting held in Denver, Colorado.

72

Development of gas-bearing reservoirs in the Trenton Llimestone Formation of New York. Final report  

SciTech Connect

The Energy Authority completed a study of the natural gas-bearing potential of New York State's Trenton Limestone Formation. The report includes an analysis of existing gas-well information and geological maps covering 33 counties in western and central New York State. The Trenton Limestone Formation is a limestone sequence with zones of shale interbeds that, when jointed and fractured, form reservoirs for natural gas. These reservoirs appear to be large and capable of sustained production, providing the production rates are carefully monitored to maintain reservoir pressure. Test wells have shown evidence of natural gas in all areas where the formation is present. The areas with the greatest reservoir potential trend from northeast to southwest beginning near the Adirondack foothills in Oneida County. When reservoir volumes are matched with a high success rate of discovery and minimum drilling costs, the northeastern part of central New York State appears to be the most likely region for both local use and commercial exploration. The Trenton formation in this area of the State generally contains gas at above-normal hydrostatic pressure. This indicates that the gas reservoirs are extensive and reach considerable depths. Due to the geophysical conditions of the reservoirs, however, it is important to carefully manage production and maintain pre-production pressure for optimum gas recovery.

Robinson, J.E.

1985-12-01T23:59:59.000Z

73

Blackfoot Reservoir Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Blackfoot Reservoir Geothermal Area Blackfoot Reservoir Geothermal Area (Redirected from Blackfoot Reservoir Area) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Blackfoot Reservoir Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (0) 9 Exploration Activities (3) 10 References Area Overview Geothermal Area Profile Location: Idaho Exploration Region: Northern Basin and Range Geothermal Region GEA Development Phase: 2008 USGS Resource Estimate Mean Reservoir Temp: Estimated Reservoir Volume: Mean Capacity: Click "Edit With Form" above to add content History and Infrastructure Operating Power Plants: 0

74

Modeling of Geothermal Reservoirs: Fundamental Processes, Computer  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » Modeling of Geothermal Reservoirs: Fundamental Processes, Computer Simulation and Field Applications Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Modeling of Geothermal Reservoirs: Fundamental Processes, Computer Simulation and Field Applications Abstract This article attempts to critically evaluate the present state of the art of geothermal reservoir simulation. Methodological aspects of geothermal reservoir modeling are briefly reviewed, with special emphasis on flow in fractured media. We then examine some applications of numerical simulation to studies of reservoir dynamics, well test design and analysis, and modeling of specific fields. Tangible impacts of reservoir simulation

75

ARM - Measurement - Aerosol optical depth  

NLE Websites -- All DOE Office Websites (Extended Search)

depth depth ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Aerosol optical depth A measure of how much light aerosols prevent from passing through a column of atmosphere. Categories Aerosols Instruments The above measurement is considered scientifically relevant for the following instruments. Refer to the datastream (netcdf) file headers of each instrument for a list of all available measurements, including those recorded for diagnostic or quality assurance purposes. ARM Instruments HSRL : High Spectral Resolution Lidar MPL : Micropulse Lidar MFRSR : Multifilter Rotating Shadowband Radiometer NIMFR : Normal Incidence Multifilter Radiometer Field Campaign Instruments AOS-PMFOV : Acoustical Optical Spectrometer-Photometer with Multiple

76

ARM - Measurement - Cloud optical depth  

NLE Websites -- All DOE Office Websites (Extended Search)

optical depth optical depth ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Cloud optical depth Amount of light cloud droplets or ice particles prevent from passing through a column of atmosphere. Categories Cloud Properties Instruments The above measurement is considered scientifically relevant for the following instruments. Refer to the datastream (netcdf) file headers of each instrument for a list of all available measurements, including those recorded for diagnostic or quality assurance purposes. External Instruments GOES : Geostationary Operational Environmental Satellites Field Campaign Instruments EC-CONVAIR580-BULK : Environment Canada Convair 580 Bulk Parameters GOES : Geostationary Operational Environmental Satellites

77

Year Average Transportation Cost of Coal  

Gasoline and Diesel Fuel Update (EIA)

delivered costs of coal, by year and primary transport mode Year Average Transportation Cost of Coal (Dollars per Ton) Average Delivered Cost of Coal (Dollars per Ton)...

78

Seismic modeling of complex stratified reservoirs  

E-Print Network (OSTI)

for such complex reservoirs is crucial and necessary to reduce exploration risk. A fast and accurate approach generating synthetic seismograms for such reservoir models combines wavefront construction ray tracing with composite reflection coefficients in a hybrid...

Lai, Hung-Liang

2009-05-15T23:59:59.000Z

79

Simplified methods of modeling multilayer reservoirs  

E-Print Network (OSTI)

The purpose of this study is to develop simplified methods to model multilayer reservoirs. We examined the method to model well responses of multilayer reservoirs with equivalent single layer solutions during transient flow period which Bennett...

Ryou, Sangsoo

1993-01-01T23:59:59.000Z

80

Comparative Evaluation of Generalized River/Reservoir System Models  

E-Print Network (OSTI)

This report reviews user-oriented generalized reservoir/river system models. The terms reservoir/river system, reservoir system, reservoir operation, or river basin management "model" or "modeling system" are used synonymously to refer to computer...

Wurbs, Ralph A.

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Reservoir compaction loads on casings and liners  

SciTech Connect

Pressure drawdown due to production from a reservoir causes compaction of the reservoir formation which induces axial and radial loads on the wellbore. Reservoir compaction loads increase during the production life of a well, and are greater for deviated wells. Presented here are casing and liner loads at initial and final pressure drawdowns for a particular reservoir and at well deviation angles of 0 to 45 degrees.

Wooley, G.R.; Prachner, W.

1984-09-01T23:59:59.000Z

82

Optimization Online - Managing Hydroelectric Reservoirs over an ...  

E-Print Network (OSTI)

Jul 7, 2013 ... Managing Hydroelectric Reservoirs over an Extended Planning Horizon using a Benders Decomposition Algorithm Exploiting a Memory Loss...

Pierre-Luc Carpentier

2013-07-07T23:59:59.000Z

83

Tenth workshop on geothermal reservoir engineering: proceedings  

SciTech Connect

The workshop contains presentations in the following areas: (1) reservoir engineering research; (2) field development; (3) vapor-dominated systems; (4) the Geysers thermal area; (5) well test analysis; (6) production engineering; (7) reservoir evaluation; (8) geochemistry and injection; (9) numerical simulation; and (10) reservoir physics. (ACR)

Not Available

1985-01-22T23:59:59.000Z

84

STIMULATION AND RESERVOIR ENGINEERING OF GEOTHERMAL RESOURCES  

E-Print Network (OSTI)

STIMULATION AND RESERVOIR ENGINEERING OF GEOTHERMAL RESOURCES Paul Kruger and Henry J . Ramey, Jr . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 THE GEOTHERMAL CHIMNEY MODEL . . . . . . . . . . . . . . . . . . . 3 Current Design of t h e . . . . . . . . . . . . . . . 67 Geothermal Reservoir Phy.Sica1 PIodels . . . . . . . . . . . . 73 RAD3N I N GEOTHERMAL RESERVOIRS

Stanford University

85

Hydroelectric Reservoirs -the Carbon Dioxide and Methane  

E-Print Network (OSTI)

Hydroelectric Reservoirs - the Carbon Dioxide and Methane Emissions of a "Carbon Free" Energy an overview on the greenhouse gas production of hydroelectric reservoirs. The goals are to point out the main how big the greenhouse gas emissions from hydroelectric reservoirs are compared to thermo-power plants

Fischlin, Andreas

86

Increasing Waterflooding Reservoirs in the Wilmington Oil Field through Improved Reservoir Characterization and Reservoir Management, Class III  

SciTech Connect

This project was intended to increase recoverable waterflood reserves in slope and basin reservoirs through improved reservoir characterization and reservoir management. The particular application of this project is in portions of Fault Blocks IV and V of the Wilmington Oil Field, in Long Beach, California, but the approach is widely applicable in slope and basin reservoirs, transferring technology so that it can be applied in other sections of the Wilmington field and by operators in other slope and basin reservoirs is a primary component of the project.

Koerner, Roy; Clarke, Don; Walker, Scott; Phillips, Chris; Nguyen, John; Moos, Dan; Tagbor, Kwasi

2001-08-07T23:59:59.000Z

87

The role of reservoir characterization in the reservoir management process (as reflected in the Department of Energy`s reservoir management demonstration program)  

SciTech Connect

Optimum reservoir recovery and profitability result from guidance of reservoir practices provided by an effective reservoir management plan. Success in developing the best, most appropriate reservoir management plan requires knowledge and consideration of (1) the reservoir system including rocks, and rock-fluid interactions (i.e., a characterization of the reservoir) as well as wellbores and associated equipment and surface facilities; (2) the technologies available to describe, analyze, and exploit the reservoir; and (3) the business environment under which the plan will be developed and implemented. Reservoir characterization is the essential to gain needed knowledge of the reservoir for reservoir management plan building. Reservoir characterization efforts can be appropriately scaled by considering the reservoir management context under which the plan is being built. Reservoir management plans de-optimize with time as technology and the business environment change or as new reservoir information indicates the reservoir characterization models on which the current plan is based are inadequate. BDM-Oklahoma and the Department of Energy have implemented a program of reservoir management demonstrations to encourage operators with limited resources and experience to learn, implement, and disperse sound reservoir management techniques through cooperative research and development projects whose objectives are to develop reservoir management plans. In each of the three projects currently underway, careful attention to reservoir management context assures a reservoir characterization approach that is sufficient, but not in excess of what is necessary, to devise and implement an effective reservoir management plan.

Fowler, M.L. [BDM-Petroleum Technologies, Bartlesville, OK (United States); Young, M.A.; Madden, M.P. [BDM-Oklahoma, Bartlesville, OK (United States)] [and others

1997-08-01T23:59:59.000Z

88

Ultrasonic material hardness depth measurement  

DOE Patents (OSTI)

The invention is an ultrasonic surface hardness depth measurement apparatus and method permitting rapid determination of hardness depth of shafts, rods, tubes and other cylindrical parts. The apparatus of the invention has a part handler, sensor, ultrasonic electronics component, computer, computer instruction sets, and may include a display screen. The part handler has a vessel filled with a couplant, and a part rotator for rotating a cylindrical metal part with respect to the sensor. The part handler further has a surface follower upon which the sensor is mounted, thereby maintaining a constant distance between the sensor and the exterior surface of the cylindrical metal part. The sensor is mounted so that a front surface of the sensor is within the vessel with couplant between the front surface of the sensor and the part.

Good, Morris S. (Richland, WA); Schuster, George J. (Kennewick, WA); Skorpik, James R. (Kennewick, WA)

1997-01-01T23:59:59.000Z

89

Blackfoot Reservoir Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Blackfoot Reservoir Geothermal Area Blackfoot Reservoir Geothermal Area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Blackfoot Reservoir Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (0) 9 Exploration Activities (3) 10 References Area Overview Geothermal Area Profile Location: Idaho Exploration Region: Northern Basin and Range Geothermal Region GEA Development Phase: 2008 USGS Resource Estimate Mean Reservoir Temp: Estimated Reservoir Volume: Mean Capacity: Click "Edit With Form" above to add content History and Infrastructure Operating Power Plants: 0 No geothermal plants listed.

90

4. International reservoir characterization technical conference  

SciTech Connect

This volume contains the Proceedings of the Fourth International Reservoir Characterization Technical Conference held March 2-4, 1997 in Houston, Texas. The theme for the conference was Advances in Reservoir Characterization for Effective Reservoir Management. On March 2, 1997, the DOE Class Workshop kicked off with tutorials by Dr. Steve Begg (BP Exploration) and Dr. Ganesh Thakur (Chevron). Tutorial presentations are not included in these Proceedings but may be available from the authors. The conference consisted of the following topics: data acquisition; reservoir modeling; scaling reservoir properties; and managing uncertainty. Selected papers have been processed separately for inclusion in the Energy Science and Technology database.

NONE

1997-04-01T23:59:59.000Z

91

An In-depth Investigation of an Aluminum Chloride Retarded Mud Acid System on Sandstone Reservoirs  

E-Print Network (OSTI)

Sandstone acidizing using mud acid is a quick and complex process where dissolution and precipitation occur simultaneously. Retarded mud acids are less reactive with the rock reducing the reaction rate hence increased penetration into the formation...

Aneto, Nnenna

2012-07-16T23:59:59.000Z

92

EXPLOITATION AND OPTIMIZATION OF RESERVOIR PERFORMANCE IN HUNTON FORMATION, OKLAHOMA  

SciTech Connect

This report presents the work done so far on Hunton Formation in West Carney Field in Lincoln County, Oklahoma. West Carney Field produces oil and gas from the Hunton Formation. The field was developed starting in 1995. Some of the unique characteristics of the field include decreasing water oil ratio over time, decreasing gas-oil ratio at the beginning of production, inability to calculate oil reserves in the field based on log data, and sustained oil rates over long periods of time. To understand the unique characteristics of the field, an integrated evaluation was undertaken. Production data from the field were meticulously collected, and over forty wells were cored and logged to better understand the petrophysical and engineering characteristics. Based on the work done in this budget period so far, some of the preliminary conclusions can be listed as follows: (1) Based on PVT analysis, the field most likely contains volatile oil with bubble point close to initial reservoir pressure of 1,900 psia. (2) The initial oil in place, which is contact with existing wells, can be determined by newly developed material balance technique. The oil in place, which is in communication, is significantly less than determined by volumetric analysis, indicating heterogeneous nature of the reservoir. The oil in place, determined by material balance, is greater than determined by decline curve analysis. This difference may lead to additional locations for in fill wells. (3) The core and log evaluation indicates that the intermediate pores (porosity between 2 and 6 %) are very important in determining production potential of the reservoir. These intermediate size pores contain high oil saturation. (4) The limestone part of the reservoir, although low in porosity (mostly less than 6 %) is much more prolific in terms of oil production than the dolomite portion of the reservoir. The reason for this difference is the higher oil saturation in low porosity region. As the average porosity increases, the remaining oil saturation decreases. This is evident from log and core analysis. (5) Using a compositional simulator, we are able to reproduce the important reservoir characteristics by assuming a two layer model. One layer is high permeability region containing water and the other layer is low permeability region containing mostly oil. The results are further verified by using a dual porosity model. Assuming that most of the volatile oil is contained in the matrix and the water is contained in the fractures, we are able to reproduce important reservoir performance characteristics. (6) Evaluation of secondary mechanisms indicates that CO{sub 2} flooding is potentially a viable option if CO{sub 2} is available at reasonable price. We have conducted detailed simulation studies to verify the effectiveness of CO{sub 2} huff-n-puff process. We are in the process of conducting additional lab tests to verify the efficacy of the same displacement. (7) Another possibility of improving the oil recovery is to inject surfactants to change the near well bore wettability of the rock from oil wet to water wet. By changing the wettability, we may be able to retard the water flow and hence improve the oil recovery as a percentage of total fluid produced. If surfactant is reasonably priced, other possibility is also to use huff-n-puff process using surfactants. Laboratory experiments are promising, and additional investigation continues. (8) Preliminary economic evaluation indicates that vertical wells outperform horizontal wells. Future work in the project would include: (1) Build multi-well numerical model to reproduce overall reservoir performance rather than individual well performance. Special emphasis will be placed on hydrodynamic connectivity between wells. (2) Collect data from adjacent Hunton reservoirs to validate our understanding of what makes it a productive reservoir. (3) Develop statistical methods to rank various reservoirs in Hunton formation. This will allow us to evaluate other Hunton formations based on old well logs, and determine, apriori, if

Mohan Kelkar

2003-10-01T23:59:59.000Z

93

Anisotropic poststack depth migration, eastern Venezuela  

SciTech Connect

It is known that in areas with significant shale content, the isotropic assumption in depth migration is not correct, and this can lead to incorrect depth positioning if not properly accounted for. In this paper, we performed isotropic and anisotropic poststack depth migrations on a dataset from Eastern Venezuela to study the influence of anisotropy over the depth migration process. When interval velocities derived from surface seismic are compared with those velocities from check shots, significant differences are observed specially for depths associated with a thick sequence of shales identified in the area. These differences in interval velocities are used to obtain estimations of the anisotropic constants used in the anisotropic depth migration process. The anisotropic depth-migrated section allows to position correctly in depth known geological markers identified in well logs, while the results in the isotropic depth-migration show some mismatch with the depths obtained from well-log information.

Uzcategui, O.J.; Mujica, D.L.

1995-12-31T23:59:59.000Z

94

Factors affecting water quality in Cherokee Reservoir  

SciTech Connect

The purpose was to: (1) define reservoir problems related to water quality conditions; (2) identify the probable causes of these problems; and (3) recommend procedures for achieving needed reservoir water quality improvements. This report presents the project findings to date and suggests steps for upgrading the quality of Cherokee Reservoir. Section II presents background information on the characteristics of the basin, the reservoir, and the beneficial uses of the reservoir. Section III identifies the impacts of existing reservoir water quality on uses of the reservoir for water supply, fishery resources, recreation, and waste assimilation. Section IV presents an assessment of cause-effect relationships. The factors affecting water quality addressed in Section IV are: (1) reservoir thermal stratification and hydrodynamics; (2) dissolved oxygen depletion; (3) eutrophication; (4) toxic substances; and (5) reservoir fisheries. Section V presents a preliminary evaluation of alternatives for improving the quality of Cherokee Reservoir. Section VI presents preliminary conclusions and recommendations for developing and implementing a reservoir water quality management plan. 7 references, 22 figures, 21 tables.

Iwanski, M.L.; Higgins, J.M.; Kim, B.R.; Young, R.C.

1980-07-01T23:59:59.000Z

95

Predicting production performance of CBM reservoirs  

Science Journals Connector (OSTI)

Prediction of gas production from the coalbed methane (CBM) reservoirs is challenging due to the complex interaction of storage and transport mechanisms. The vast majority of the gas in CBM reservoirs is stored by adsorption in the coal matrix which practically has no permeability. The flow to production wells however takes place through the cleats or the natural fracture system which store relatively small amounts of gas. These unique coal characteristics have resulted in classification of CBM as an unconventional gas resource. Gas production from CBM reservoirs is governed by gas diffusion through coal matrix followed by gas desorption into the cleat system through which the gas flows to the wellbore generally under two-phase conditions. As a result, the production profile of the CBM reservoirs greatly differs from conventional gas reservoirs. This precludes the use of common techniques such as decline curves to forecast the recovery, future revenues, and well performance. Numerical reservoir models (simulators) that incorporate the unique flow and storage characteristics of CBM reservoirs are by far the best tools for predicting the gas production from the CBM reservoirs. It is however cumbersome, time consuming, and expensive to use a complex reservoir simulator for evaluating CBM prospects when the required reservoir parameters are not available. Therefore, there is a need for a quick yet reliable tool for predicting production performance of CBM reservoirs. This paper presents a set of production type curves that can be used for predicting gas and water the production from CBM prospects. The type curves are particularly useful for parametric studies when the key characteristics are not well established. A numerical reservoir model that incorporated the unique flow and storage characteristics of CBM reservoirs was employed to develop the type curves. The impact of various reservoir parameters on the type curves was investigated to confirm the uniqueness of the type curves. The application and limitation of the type curves have been also discussed.

K. Aminian; S. Ameri

2009-01-01T23:59:59.000Z

96

Petrofacies analysis - the petrophysical tool for geologic/engineering reservoir characterization  

SciTech Connect

Petrofacies analysis is defined as the characterization and classification of pore types and fluid saturations as revealed by petrophysical measures of a reservoir. The word {open_quotes}petrofacies{close_quotes} makes an explicit link between petroleum engineers concerns with pore characteristics as arbiters of production performance, and the facies paradigm of geologists as a methodology for genetic understanding and prediction. In petrofacies analysis, the porosity and resistivity axes of the classical Pickett plot are used to map water saturation, bulk volume water, and estimated permeability, as well as capillary pressure information, where it is available. When data points are connected in order of depth within a reservoir, the characteristic patterns reflect reservoir rock character and its interplay with the hydrocarbon column. A third variable can be presented at each point on the crossplot by assigning a color scale that is based on other well logs, often gamma ray or photoelectric effect, or other derived variables. Contrasts between reservoir pore types and fluid saturations will be reflected in changing patterns on the crossplot and can help discriminate and characterize reservoir heterogeneity. Many hundreds of analyses of well logs facilitated by spreadsheet and object-oriented programming have provided the means to distinguish patterns typical of certain complex pore types for sandstones and carbonate reservoirs, occurrences of irreducible water saturation, and presence of transition zones. The result has been an improved means to evaluate potential production such as bypassed pay behind pipe and in old exploration holes, or to assess zonation and continuity of the reservoir. Petrofacies analysis is applied in this example to distinguishing flow units including discrimination of pore type as assessment of reservoir conformance and continuity. The analysis is facilitated through the use of color cross sections and cluster analysis.

Watney, W.L.; Guy, W.J.; Gerlach, P.M. [Kansas Geological Survey, Lawrence, KS (United States)] [and others

1997-08-01T23:59:59.000Z

97

Reservoir monitoring: 1990 summary of vital signs and use impairment monitoring on Tennessee Valley Reservoirs  

SciTech Connect

The Tennessee Valley Authority (TVA) initiated a Reservoir Monitoring Program on 12 TVA reservoirs (the nine main stream Tennessee river reservoirs -- Kentucky through Fort Loudoun and three major tributary storage reservoirs -- Cherokee, Douglas, and Norris) in autumn 1989. The objective of the Reservoir Monitoring Program is to provide basic information on the ``health`` or integrity of the aquatic ecosystem in each TVA reservoir (``Vital Signs``) and to provide screening level information for describing how well each reservoir meets the swimmable and fishable goals of the Clean Water Act (Use Impairments). This is the first time in the history of the agency that a commitment to a long-term, systematic sampling of major TVA reservoirs has been made. The basis of the Vital Signs Monitoring is examination of appropriate physical, chemical, and biological indicators in three areas of each reservoir. These three areas are the forebay immediately upstream of the dam; the transition zone (the mid-reservoir region where the water changes from free flowing to more quiescent, impounded water); and the inflow or headwater region of the reservoir. The Use Impairments monitoring provides screening level information on the suitability of selected areas within TVA reservoirs for water contact activities (swimmable) and suitability of fish from TVA reservoirs for human consumption (fishable).

Dycus, D.L.; Meinert, D.L.

1991-08-01T23:59:59.000Z

98

Reservoir monitoring: 1990 summary of vital signs and use impairment monitoring on Tennessee Valley Reservoirs  

SciTech Connect

The Tennessee Valley Authority (TVA) initiated a Reservoir Monitoring Program on 12 TVA reservoirs (the nine main stream Tennessee river reservoirs -- Kentucky through Fort Loudoun and three major tributary storage reservoirs -- Cherokee, Douglas, and Norris) in autumn 1989. The objective of the Reservoir Monitoring Program is to provide basic information on the health'' or integrity of the aquatic ecosystem in each TVA reservoir ( Vital Signs'') and to provide screening level information for describing how well each reservoir meets the swimmable and fishable goals of the Clean Water Act (Use Impairments). This is the first time in the history of the agency that a commitment to a long-term, systematic sampling of major TVA reservoirs has been made. The basis of the Vital Signs Monitoring is examination of appropriate physical, chemical, and biological indicators in three areas of each reservoir. These three areas are the forebay immediately upstream of the dam; the transition zone (the mid-reservoir region where the water changes from free flowing to more quiescent, impounded water); and the inflow or headwater region of the reservoir. The Use Impairments monitoring provides screening level information on the suitability of selected areas within TVA reservoirs for water contact activities (swimmable) and suitability of fish from TVA reservoirs for human consumption (fishable).

Dycus, D.L.; Meinert, D.L.

1991-08-01T23:59:59.000Z

99

Architecture and sedimentology of turbidite reservoirs from Miocene Moco T and Webster zones, Midway-Sunset field, California  

SciTech Connect

Thirty-five turbidite sandstone bodies from the Moco T and Webster reservoir zones were delineated for enhanced oil recovery projects in Mobil's MOCO FEE property, south Midway-Sunset field. The recognition of these sand bodies is based on mappable geometries determined from wireline log correlations, log character, core facies, reservoir characteristics, and comparison to nearby age-equivalent outcrops. These turbidite sands are composed of unconsolidated arkosic late Miocene sandstones (Stevens equivalent, Monterey Formation). They were deposited normal to paleoslope and trend southwest-northeast in an intraslope basin. Reservoir quality in the sandstone is very good, with average porosities of 33% and permeabilities of 1 darcy.

Link, M.H.; Hall, B.R.

1989-03-01T23:59:59.000Z

100

Hydraulic fracturing in a naturally fractured reservoir  

SciTech Connect

Hydraulic fracturing of wells in naturally fractured reservoirs can differ dramatically from fracturing wells in conventional isotropic reservoirs. Fluid leakoff is the primary difference. In conventional reservoirs, fluid leakoff is controlled by reservoir matrix and fracture fluid parameters. The fluid leakoff rate in naturally fractured reservoirs is typically excessive and completely dominated by the natural fractures. This paper presents several field examples of a fracture stimulation program performed on the naturally fractured Devonia carbonate of West Texas. Qualitative pressure decline analysis and net treating pressure interpretation techniques were utilized to evaluate the existence of natural fractures in the Devonian Formation. Quantitative techniques were utilized to assess the importance of the natural fractures to the fracturing process. This paper demonstrates that bottomhole pressure monitoring of fracture stimulations has benefits over conducting minifrac treatments in naturally fractured reservoirs. Finally, the results of this evaluation were used to redesign fracture treatments to ensure maximum productivity and minimize costs.

Britt, L.K.; Hager, C.J.; Thompson, J.W.

1994-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Pressure maintenance in a volatile oil reservoir  

E-Print Network (OSTI)

reservoir. Historically, produced and makeup gas was injected to maintain pressure. In today's economy. gas has an increasing market value compared to the price of oil. Therefore, it becomes increasingly difficult to justify economically the injection... of produced gas and the purchase of additional make up gas to maintain reservoir pressure. Accordingly, water injection to maintain pressure becomes more favorable economically. This research investigated water injection into a volatile oil reservoir...

Schuster, Bruce Alan

2012-06-07T23:59:59.000Z

102

Integrated reservoir study of the 8 reservoir of the Green Canyon 18 field  

E-Print Network (OSTI)

The move into deeper waters in the Gulf of Mexico has produced new opportunities for petroleum production, but it also has produced new challenges as different reservoir problems are encountered. This integrated reservoir characterization effort has...

Aniekwena, Anthony Udegbunam

2004-11-15T23:59:59.000Z

103

A dynamic prediction model for gas-water effective permeability in unsaturated coalbed methane reservoirs based on production data  

Science Journals Connector (OSTI)

Abstract Effective permeability of gas and water in coalbed methane (CBM) reservoirs is vital during CBM development. However, few studies have investigated it for unsaturated CBM reservoirs rather than saturated CBM reservoirs. In this work, the dynamic prediction model (PM-Corey model) for average gas-water effective permeability in two-phase flow in saturated CBM reservoirs was improved to describe unsaturated CBM reservoirs. In the improved effective permeability model, Palmer etal. absolute permeability model segmented based on critical desorption pressure and Chen etal. relative permeability model segmented based on critical water saturation were introduced and coupled comprehensively under conditions with the identical reservoir pressures and the identical water saturations through production data and the material balance equations (MBEs) in unsaturated CBM reservoirs. Taking the Hancheng CBM field as an example, the differences between the saturated and unsaturated effective permeability curves were compared. The results illustrate that the new dynamic prediction model could characterize not only the stage of two-phase flow but also the stage of single-phase water drainage. Also, the new model can accurately reflect the comprehensive effects of the positive and negative effects (the matrix shrinking effect and the effective stress effect) and the gas Klinkenberg effect of coal reservoirs, especially for the matrix shrinkage effect and the gas Klinkenberg effect, which can improve the effective permeability of gas production and render the process more economically. The new improved model is more realistic and practical than previous models.

Junlong Zhao; Dazhen Tang; Hao Xu; Yanjun Meng; Yumin Lv; Shu Tao

2014-01-01T23:59:59.000Z

104

ARM - Evaluation Product - MicroPulse LIDAR Cloud Optical Depth (MPLCOD)  

NLE Websites -- All DOE Office Websites (Extended Search)

ProductsMicroPulse LIDAR Cloud Optical Depth ProductsMicroPulse LIDAR Cloud Optical Depth (MPLCOD) Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Evaluation Product : MicroPulse LIDAR Cloud Optical Depth (MPLCOD) 1999.05.01 - 2004.05.14 Site(s) SGP General Description The MPLCOD VAP retrieves the column cloud visible optical depth using LIDAR derived backscatter from the MPLNOR (Micro Pulse Lidar Normalized Backscatter) and radiosonde thermodynamic profiles. The optical depth retrieval is derived following Comstock et al. (2001), which retrieves visible optical depth and layer average backscatter-to-extinction ratio (k) at the lidar wavelength for each backscatter profile. Data Information Data Directory Contacts Principal Investigator Jennifer Comstock (509) 372-424

105

Radioactive Marker Measurements in Heterogeneous Reservoirs ...  

E-Print Network (OSTI)

quence of subsurface fluid water, gas, oil production e.g., Gam- ...... reservoirs.'' J. Pet. Technol., 25, 734744. Gonzalez-Moran, T., Rodriguez, R., and Cortes,...

2004-05-04T23:59:59.000Z

106

The internal wave field in Sau reservoir  

Science Journals Connector (OSTI)

The analysis of wind, temperature, and current data from Sau reservoir (Spain) shows that the third vertical mode ..... However, increased computing power.

2005-06-16T23:59:59.000Z

107

Storage capacity in hot dry rock reservoirs  

DOE Patents (OSTI)

A method of extracting thermal energy, in a cyclic manner, from geologic strata which may be termed hot dry rock. A reservoir comprised of hot fractured rock is established and water or other liquid is passed through the reservoir. The water is heated by the hot rock, recovered from the reservoir, cooled by extraction of heat by means of heat exchange apparatus on the surface, and then re-injected into the reservoir to be heated again. Water is added to the reservoir by means of an injection well and recovered from the reservoir by means of a production well. Water is continuously provided to the reservoir and continuously withdrawn from the reservoir at two different flow rates, a base rate and a peak rate. Increasing water flow from the base rate to the peak rate is accomplished by rapidly decreasing backpressure at the outlet of the production well in order to meet periodic needs for amounts of thermal energy greater than a baseload amount, such as to generate additional electric power to meet peak demands. The rate of flow of water provided to the hot dry rock reservoir is maintained at a value effective to prevent depletion of the liquid

Brown, Donald W. (Los Alamos, NM)

1997-01-01T23:59:59.000Z

108

International reservoir operations agreement helps NW fish &...  

NLE Websites -- All DOE Office Websites (Extended Search)

or 503-230-5131 International reservoir operations agreement helps Northwest fish and power Portland, Ore. - The Bonneville Power Administration and the British Columbia...

109

Evaluation Of Chemical Geothermometers For Calculating Reservoir...  

Open Energy Info (EERE)

Geothermometers For Calculating Reservoir Temperatures At Nevada Geothermal Power Plants Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper:...

110

Geothermal: Sponsored by OSTI -- Reservoir Pressure Management  

Office of Scientific and Technical Information (OSTI)

Reservoir Pressure Management Geothermal Technologies Legacy Collection HelpFAQ | Site Map | Contact Us | Admin Log On HomeBasic Search About Publications Advanced Search New Hot...

111

Analysis of Geothermal Reservoir Stimulation Using Geomechanics...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

System (EGS) Reservoir; 2010 Geothermal Technology Program Peer Review Report Seismic Fracture Characterization Methods for Enhanced Geothermal Systems; 2010 Geothermal Technology...

112

Mapping Diffuse Seismicity for Geothermal Reservoir Management...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Templeton David B. Harris Lawrence Livermore Natl. Lab. Seismicity and Reservoir Fracture Characterization May 18, 2010 This presentation does not contain any proprietary...

113

The internal wave field in Sau reservoir  

Science Journals Connector (OSTI)

The analysis of wind, temperature, and current data from Sau reservoir (Spain) shows that the ... of the total wind energy input into the lake (West and Lorke.

2005-06-16T23:59:59.000Z

114

Safety of Dams and Reservoirs Act (Nebraska)  

Energy.gov (U.S. Department of Energy (DOE))

This act regulates dams and associated reservoirs to protect health and public safety and minimize adverse consequences associated with potential dam failure. The act describes the responsibilities...

115

Performance modeling of an integral, self-regulating cesium reservoir for the ATI-TFE  

SciTech Connect

This work covers the performance modeling of an integral metal-matrix cesium-graphite reservoir for operation in the Advanced Thermionic Initiative-Thermionic Fuel Element (ATI-TFE) converter configuration. The objectives of this task were to incorporate an intercalated cesium-graphite reservoir for the 3C[sub 24]Cs[r arrow]2C[sub 36]Cs+Cs[sub (g)] two phase equilibrium reaction into the emitter lead region of the ATI-TFE. A semi two-dimensional, cylindrical TFE computer model was used to obtain thermal and electrical converter output characteristics for various reservoir locations. The results of this study are distributions for the interelectrode voltage, output current density, and output power density as a function of axial position along the TFE emitter. This analysis was accomplished by identifying an optimum cesium pressure for three representative pins in the ATI driverless'' reactor core and determining the corresponding position of the graphite reservoir in the ATI-TFE lead region. The position for placement of the graphite reservoir was determined by performing a first-order heat transfer analysis of the TFE lead region to determine its temperature distribution. The results of this analysis indicate that for the graphite reservoirs investigated the 3C[sub 24]Cs[r arrow]2C[sub 36]Cs+Cs[sub (g)] equilibrium reaction reservoir is ideal for placement in the TFE emitter lead region. This reservoir can be directly coupled to the emitter, through conduction, to provide the desired cesium pressure for optimum performance. The cesium pressure corresponding to the optimum converter output performance was found to be 2.18 torr for the ATI core least power TFE, 2.92 torr for the average power TFE, and 4.93 torr for the maximum power TFE.

Thayer, K.L.; Ramalingam, M.L. (UES, In., 4401 Dayton-Xenia Road, Dayton, Ohio 45432-1894 (United States)); Young, T.J. (Aerospace Power Division, Wright Laboratory/POOC, Wright-Patterson AFB, Ohio 45433-6563 (United States))

1993-01-20T23:59:59.000Z

116

Factors controlling reservoir quality in tertiary sandstones and their significance to geopressured geothermal production  

SciTech Connect

Variable intensity of diagenesis is the factor primarily responsible for contrasting regional reservoir quality of Tertiary sandstones from the upper and lower Texas coast. Detailed comparison of Frio sandstone from the Chocolate Bayou/Danbury Dome area, Brazoria County, and Vicksburg sandstones from the McAllen Ranch Field area, Hidalgo County, reveals that extent of diagenetic modification is most strongly influenced by (1) detrital mineralogy and (2) regional geothermal gradients. The regional reservoir quality of Frio sandstones from Brazoria County is far better than that characterizing Vicksburg sandstones from Hidalgo County, especially at depths suitable for geopressured geothermal energy production. However, in predicting reservoir quality on a site-specific basis, locally variable factors such as relative proportions for porosity types, pore geometry as related to permeability, and local depositional environment must also be considered. Even in an area of regionally favorable reservoir quality, such local factors can significantly affect reservoir quality and, hence, the geothermal production potential of a specific sandstone unit.

Loucks, R.G.; Richmann, D.L.; Milliken, K.L.

1981-01-01T23:59:59.000Z

117

Seismic signatures of the Lodgepole fractured reservoir in Utah-Wyoming overthrust belt  

SciTech Connect

In low porosity, low permeability zones, natural fractures are the primary source of permeability which affect both production and injection of fluids. The open fractures do not contribute much to porosity, but they provide an increased drainage network to any porosity. An important approach to characterizing the fracture orientation and fracture permeability of reservoir formations is one based upon the effects of such conditions on the propagation of acoustic and seismic waves in the rock. We present the feasibility of using seismic measurement techniques to map the fracture zones between wells spaced 2400 ft at depths of about 1000 ft. For this purpose we constructed computer models (which include azimuthal anisotropy) using Lodgepole reservoir parameters to predict seismic signatures recorded at the borehole scale, crosswell scale, and 3 D seismic scale. We have integrated well logs with existing 2D surfaces seismic to produce petrophysical and geological cross sections to determine the reservoir parameters and geometry for the computer models. In particular, the model responses are used to evaluate if surface seismic and crosswell seismic measurements can capture the anisotropy due to vertical fractures. Preliminary results suggested that seismic waves transmitted between two wells will propagate in carbonate fracture reservoirs, and the signal can be received above the noise level at the distance of 2400 ft. In addition, the large velocities contrast between the main fracture zone and the underlying unfractured Boundary Ridge Member, suggested that borehole reflection imaging may be appropriate to map and fracture zone thickness variation and fracture distributions in the reservoir.

Parra, J.; Collier, H.; Angstman, B.

1997-08-01T23:59:59.000Z

118

The relationship between petroleum emplacement and carbonate reservoir quality: examples from Abu Dhabi and the Amu Darya Basin  

Science Journals Connector (OSTI)

The relative importance of petroleum emplacement in inhibiting diagenetic processes and preserving porosity and permeability in Lower Cretaceous, Thamama Group (Kharaib Formation) carbonate reservoirs of Abu Dhabi, UAE, and in Callovian-Kimmeridgian carbonate reservoirs of the Amu Darya Basin in Uzbekistan and Turkmenistan, has been evaluated by combining geologic, petrophysical and geochemical data. When petroleum emplacement is synchronous with and prior to significant burial cementation in carbonates, primary petroleum inclusions are trapped in the cements. The process appears to be characterised by steep intra-field porosity-depth trends within a more gradual regional decline in porosity with depth. This has profound implications for the prediction of porosity in carbonate reservoirs. Reservoir quality is better in grainstones and packstones compared to adjacent wackestones and lime mudstones in the Kharaib Formation because of preserved macroporosity (intergranular, vuggy, mouldic); the pore system in the finer units is dominated by micropores. These features indicate a primary textural control on porosity and permeability. Within the grainstones and packstones, macroporosity is variably filled by late equant sparry calcite cements. Porosity and permeability variations in grainstones and packstones at a reservoir scale are therefore controlled by the variation in amount of equant sparry calcite cement. This in turn depends on the timing of the precipitation of this cement relative to petroleum emplacement, as shown by fluid inclusion data. Where petroleum emplacement has occurred relatively early, at migration foci, prior to significant burial cementation by equant sparry calcite, reservoir quality is preserved. Where it has occurred after significant burial cementation, reservoir quality has been destroyed. In the Amu Darya sequences, primary macroporosity is commonly preserved down to depths of 11,000 ft (3.5 km) with differences in the porosity and permeability characteristics of grainstones being controlled by variations in the amount of early, probably freshwater, cement and the extent of associated dissolution. Small volumes of burial cements do occur, but they do not contain petroleum inclusions. Consequently, there is no firm evidence that petroleum emplacement has inhibited diagenesis in this area. This part of the study has shown that it is not always possible to obtain conclusive evidence from the diagenesis to pin down the processes responsible for the preservation of reservoir quality and that petroleum filling may not always be the primary cause. The relationships documented here show that the race for space between diagenetic waters and petroleum is a major control on reservoir quality in the Thamama Group carbonate reservoirs, but is not so important for the Jurassic carbonates in the Amu Darya basin.

Joyce E. Neilson; Norman H. Oxtoby; Michael D. Simmons; Ivor R. Simpson; Natalia K. Fortunatova

1998-01-01T23:59:59.000Z

119

Reservoir characterization using experimental design and response surface methodology  

E-Print Network (OSTI)

This research combines a statistical tool called experimental design/response surface methodology with reservoir modeling and flow simulation for the purpose of reservoir characterization. Very often, it requires large number of reservoir simulation...

Parikh, Harshal

2004-09-30T23:59:59.000Z

120

New depths with mobile rig  

SciTech Connect

Magee-Poole Drilling Company, a drilling contractor operating out of the south Texas drilling center of Alice, claims it operates the largest mobile drilling rig in the world. That is, it's the only wheel mounted portable rig that drills to 16,000 feet with 4 1/2-inch drill pipe - at least 3000 feet deeper than the previous mobile drilling rig ratings. The unit is designated the Ingersoll-Rand 1500 Series. What's more significant, according to co-owner Don Magee, is that the rig's portability gets the rotary table turning to the right sooner; it drills more footage per year. It rigs up in 1 1/2 days versus 3 to 4 days for a conventional skid type rig normally used at these depths. The unit's compact arrangement, with more components combined into single loads, makes possible its higher mobility. A conventional skid rig might require 25 to 30 truckloads to move the rig components, mud system, fuel and water tank, houses for utilities, storage and crew change, generators, and drill pipe. The new rig moves in anywhere from four to nine loads less. Further, the rig components weigh less without sacrificing durability.

Not Available

1982-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Electromagnetic Heating Methods for Heavy Oil Reservoirs  

SciTech Connect

The most widely used method of thermal oil recovery is by injecting steam into the reservoir. A well-designed steam injection project is very efficient in recovering oil, however its applicability is limited in many situations. Simulation studies and field experience has shown that for low injectivity reservoirs, small thickness of the oil-bearing zone, and reservoir heterogeneity limits the performance of steam injection. This paper discusses alternative methods of transferring heat to heavy oil reservoirs, based on electromagnetic energy. They present a detailed analysis of low frequency electric resistive (ohmic) heating and higher frequency electromagnetic heating (radio and microwave frequency). They show the applicability of electromagnetic heating in two example reservoirs. The first reservoir model has thin sand zones separated by impermeable shale layers, and very viscous oil. They model preheating the reservoir with low frequency current using two horizontal electrodes, before injecting steam. The second reservoir model has very low permeability and moderately viscous oil. In this case they use a high frequency microwave antenna located near the producing well as the heat source. Simulation results presented in this paper show that in some cases, electromagnetic heating may be a good alternative to steam injection or maybe used in combination with steam to improve heavy oil production. They identify the parameters which are critical in electromagnetic heating. They also discuss past field applications of electromagnetic heating including technical challenges and limitations.

Sahni, A.; Kumar, M.; Knapp, R.B.

2000-05-01T23:59:59.000Z

122

Water quality management plan for Cherokee Reservoir  

SciTech Connect

The management plan provides an assessment of Cherokee Reservoir's current water quality, identifies those factors which affect reservoir water quality, and develops recommendations aimed at restoring or maintaining water quality at levels sufficient to support diverse beneficial uses. 20 references, 8 figures, 15 tables. (ACR)

Not Available

1984-01-01T23:59:59.000Z

123

Property:SalinityAverage | Open Energy Information  

Open Energy Info (EERE)

SalinityAverage SalinityAverage Jump to: navigation, search Property Name SalinityAverage Property Type Number Description Mean average of the low and high end measurements of the salinity [ppm] of the fluid. This is a property of type Page. Subproperties This property has the following 1 subproperty: C Coso Geothermal Area Pages using the property "SalinityAverage" Showing 19 pages using this property. A Amedee Geothermal Area + 975 + B Beowawe Hot Springs Geothermal Area + 700 + Blue Mountain Geothermal Area + 4300 + Brady Hot Springs Geothermal Area + 3500 + C Chena Geothermal Area + 325 + D Desert Peak Geothermal Area + 6700 + Dixie Valley Geothermal Area + 2295 + E East Mesa Geothermal Area + 3750 + G Geysers Geothermal Area + 217 + K Kilauea East Rift Geothermal Area + 18750 +

124

Assessing the Radiative Impact of Clouds of Low Optical Depth  

NLE Websites -- All DOE Office Websites (Extended Search)

the Radiative Impact of Clouds of the Radiative Impact of Clouds of Low Optical Depth W. O'Hirok and P. Ricchiazzi Institute for Computational Earth System Science University of California Santa Barbara, California C. Gautier Department of Geography and Institute for Computational Earth System Science University of California Santa Barbara, California Introduction Analysis from the International Satellite Cloud Climatology Project (ISCCP) reveals that the global mean cloud optical depth is surprisingly low (i.e., τ = 3.8). While this value is probably dominated by extensive fields of cirrus, the average for liquid water clouds is also likely smaller than expected. It is in this regime (τ <10) where remote measurements of cloud optical thickness or liquid water path (LWP)

125

Eight-year Climatology of Dust Optical Depth on Mars  

E-Print Network (OSTI)

We have produced a multiannual climatology of airborne dust from Martian year 24 to 31 using multiple datasets of retrieved or estimated column optical depths. The datasets are based on observations of the Martian atmosphere from April 1999 to July 2013 made by different orbiting instruments: the Thermal Emission Spectrometer (TES) aboard Mars Global Surveyor, the Thermal Emission Imaging System (THEMIS) aboard Mars Odyssey, and the Mars Climate Sounder (MCS) aboard Mars Reconnaissance Orbiter (MRO). The procedure we have adopted consists of gridding the available retrievals of column dust optical depth (CDOD) from TES and THEMIS nadir observations, as well as the estimates of this quantity from MCS limb observations. Our gridding method calculates averages and uncertainties on a regularly spaced, but possibly incomplete, spatio-temporal grid, using an iterative procedure weighted in space, time, and retrieval uncertainty. In order to evaluate strengths and weaknesses of the resulting gridded maps, we validat...

Montabone, L; Millour, E; Wilson, R J; Lewis, S R; Cantor, B A; Kass, D; Kleinboehl, A; Lemmon, M; Smith, M D; Wolff, M J

2014-01-01T23:59:59.000Z

126

Colorado Crude Oil Reserves in Nonproducing Reservoirs (Million...  

Annual Energy Outlook 2012 (EIA)

Reserves in Nonproducing Reservoirs (Million Barrels) Colorado Crude Oil Reserves in Nonproducing Reservoirs (Million Barrels) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5...

127

INJECTION AND THERMAL BREAKTHROUGH IN FRACTURED GEOTHERMAL RESERVOIRS  

E-Print Network (OSTI)

geothermal reservoirs (except those in the Imperial Valley)Geothermal resource and reservoir investigation of U.S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley,

Bodvarsson, Gudmundur S.

2012-01-01T23:59:59.000Z

128

Reservoir Operation by Ant Colony Optimization Algorithms M. R. ...  

E-Print Network (OSTI)

Reservoir Operation by Ant Colony Optimization Algorithms. 1. Reservoir Operation by Ant Colony Optimization Algorithms. M. R. Jalali1; A. Afshar2; and M. A....

Jalali

2000-11-05T23:59:59.000Z

129

Louisiana State Offshore Crude Oil + Lease Condensate New Reservoir...  

U.S. Energy Information Administration (EIA) Indexed Site

New Reservoir Discoveries in Old Fields (Million Barrels) Louisiana State Offshore Crude Oil + Lease Condensate New Reservoir Discoveries in Old Fields (Million Barrels) Decade...

130

Texas--State Offshore Crude Oil Reserves in Nonproducing Reservoirs...  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil Reserves in Nonproducing Reservoirs (Million Barrels) Texas--State Offshore Crude Oil Reserves in Nonproducing Reservoirs (Million Barrels) Decade Year-0 Year-1 Year-2...

131

ORIGINAL PAPER Photomineralization in a boreal hydroelectric reservoir  

E-Print Network (OSTI)

ORIGINAL PAPER Photomineralization in a boreal hydroelectric reservoir: a comparison with natural dioxide Á Dissolved organic matter Á Boreal hydroelectric reservoir Á Greenhouse gas production

Long, Bernard

132

Predicting Reservoir System Quality and Performance | Open Energy...  

Open Energy Info (EERE)

Predicting Reservoir System Quality and Performance Jump to: navigation, search OpenEI Reference LibraryAdd to library Book Section: Predicting Reservoir System Quality and...

133

The Optimization of Well Spacing in a Coalbed Methane Reservoir.  

E-Print Network (OSTI)

??Numerical reservoir simulation has been used to describe mechanism of methane gas desorption process, diffusion process, and fluid flow in a coalbed methane reservoir. The (more)

Sinurat, Pahala Dominicus

2012-01-01T23:59:59.000Z

134

Oklahoma Coalbed Methane Proved Reserves New Reservoir Discoveries...  

U.S. Energy Information Administration (EIA) Indexed Site

New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Oklahoma Coalbed Methane Proved Reserves New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Decade Year-0...

135

Wyoming Coalbed Methane Proved Reserves New Reservoir Discoveries...  

U.S. Energy Information Administration (EIA) Indexed Site

New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Wyoming Coalbed Methane Proved Reserves New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Decade Year-0...

136

Utah Coalbed Methane Proved Reserves New Reservoir Discoveries...  

U.S. Energy Information Administration (EIA) Indexed Site

New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Utah Coalbed Methane Proved Reserves New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Decade Year-0 Year-1...

137

An Updated Conceptual Model Of The Los Humeros Geothermal Reservoir...  

Open Energy Info (EERE)

Humeros Geothermal Reservoir (Mexico) Abstract An analysis of production and reservoir engineering data of 42 wells from the Los Humeros geothermal field (Mexico) allowed...

138

Use Of Electrical Surveys For Geothermal Reservoir Characterization...  

Open Energy Info (EERE)

Of Electrical Surveys For Geothermal Reservoir Characterization- Beowawe Geothermal Field Abstract The STAR geothermal reservoir simulator was used to model the natural state of...

139

Modeling wettability alteration in naturally fractured carbonate reservoirs.  

E-Print Network (OSTI)

??The demand for energy and new oil reservoirs around the world has increased rapidly while oil recovery from depleted reservoirs has become more difficult. Oil (more)

Goudarzi, Ali

2012-01-01T23:59:59.000Z

140

Quantum reservoirs with ion chains  

E-Print Network (OSTI)

Ion chains are promising platforms for studying and simulating quantum reservoirs. One interesting feature is that their vibrational modes can mediate entanglement between two objects which are coupled through the vibrational modes of the chain. In this work we analyse entanglement between the transverse vibrations of two heavy impurity defects embedded in an ion chain, which is generated by the coupling with the chain vibrations. We verify general scaling properties of the defects dynamics and demonstrate that entanglement between the defects can be a stationary feature of these dynamics. We then analyse entanglement in chains composed of tens of ions and propose a measurement scheme which allows one to verify the existence of the predicted entangled state.

B. G. Taketani; T. Fogarty; E. Kajari; Th. Busch; Giovanna Morigi

2014-02-06T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Reservoir evaluation of the Lower Silurian Longmaxi Formation shale gas in the southern Sichuan Basin of China  

Science Journals Connector (OSTI)

Abstract The Lower Silurian Longmaxi Formation (the Palaeozoic) is organic-rich (black) shale in the southern Sichuan Basin (the Yangtze Plate) of China. This study analyses the lateral extent and thickness, burial depth, total organic carbon content and thermal maturity of the Longmaxi Formation black shale as the key features of the shale gas reservoir. The thickness of the black shale ranges from 10 to 170m. The thickest reservoir is located in Changning-Naxi-Yongchuan region. The TOC of the shale at the bottom of the formation (50-m thickness) is above 2.0%. The lateral distribution of TOC varies with the lateral distribution of thickness, with the maximum TOC in the Gongxian-Luzhou-Yongchuan region. The burial depth ranges from 2000 to 4500m. The shale is thermally over mature. The evaluation of reservoir characteristics indicates that the Longmaxi Formation has conditions appropriate for shale gas accumulation and thus resource potential in the southern Sichuan Basin of China. The objective of this preliminary evaluation of the reservoir characteristics is to locate potential areas favourable for exploration. The most favourable areas are defined here as those where the thickness of black shale is more than 100m and the burial depth is less than 3000m; these cover approximately 12,600km2. The most favourable areas, which cover an area of approximately 5100km2, are located in the northeast Luzhou region.

Shangbin Chen; Yanming Zhu; Yong Qin; Hongyan Wang; Honglin Liu; Junhua Fang

2014-01-01T23:59:59.000Z

142

Regional averaging and scaling in relativistic cosmology  

E-Print Network (OSTI)

Averaged inhomogeneous cosmologies lie at the forefront of interest, since cosmological parameters like the rate of expansion or the mass density are to be considered as volume-averaged quantities and only these can be compared with observations. For this reason the relevant parameters are intrinsically scale-dependent and one wishes to control this dependence without restricting the cosmological model by unphysical assumptions. In the latter respect we contrast our way to approach the averaging problem in relativistic cosmology with shortcomings of averaged Newtonian models. Explicitly, we investigate the scale-dependence of Eulerian volume averages of scalar functions on Riemannian three-manifolds. We propose a complementary view of a Lagrangian smoothing of (tensorial) variables as opposed to their Eulerian averaging on spatial domains. This program is realized with the help of a global Ricci deformation flow for the metric. We explain rigorously the origin of the Ricci flow which, on heuristic grounds, has already been suggested as a possible candidate for smoothing the initial data set for cosmological spacetimes. The smoothing of geometry implies a renormalization of averaged spatial variables. We discuss the results in terms of effective cosmological parameters that would be assigned to the smoothed cosmological spacetime.

Thomas Buchert; Mauro Carfora

2002-10-11T23:59:59.000Z

143

Average Data for Each Choke Setting (before 24-May 2010 06:00), 6-hour average (  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Average Data for Each Choke Setting (before 24-May 2010 06:00), 6-hour average (after 24-May 2010 06:00):" Average Data for Each Choke Setting (before 24-May 2010 06:00), 6-hour average (after 24-May 2010 06:00):" ,,"Choke","Average","Average","Fluid","Methanol","Water","Oil","Gas","Hyd. Eq.","Gas" ,"Choke","Setting","Upstream","Upstream","Recovery","Recovery","Recovery","Recovery","Recovery","Recovery","Recovery" "Date and Time","Setting","Duration","Pressure","Temp.","Rate","Rate","Rate","Rate","Rate","Rate","Portion" "dd-mmm-yy","(64ths)","(hours)","(psia)","(degF)","(bfpd)","(bfpd)","(bwpd)","(bopd)","(mmcfpd)","(boepd)","(%)"

144

Effects of a reduction of blue tilapia Oreochromis aureus on the ichthyofauna of a power-plant reservoir  

E-Print Network (OSTI)

Administration 1986). Thus, the number of thermally altered habitats is substantial and increasing. This will mean more suitable habitat will be created for exotic species such as the blue tilapia Oreochromis (= ~T'I i = S tb d ) ~ . 7i1 pt b-t p' 4 fishes.... Mean depth of the reservoir is 6. 5 m. A 586 ha lease to the Texas Parks and Wildlife Department (TPWD) resulted in the establishment of Fairfield Lake State Recreation Area, located at the south end of' the reservoir. Data were obtained at seven...

Starling, Scott Michael

1986-01-01T23:59:59.000Z

145

STEO January 2013 - average gasoline prices  

U.S. Energy Information Administration (EIA) Indexed Site

gasoline prices are expected to decline over the next two years. The average pump price for regular unleaded gasoline was 3.63 a gallon during 2012. That is expected to fall...

146

average air temperature | OpenEI  

Open Energy Info (EERE)

average air temperature average air temperature Dataset Summary Description (Abstract): Air Temperature at 10 m Above The Surface Of The Earth (deg C)NASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Nov 2007)22-year Monthly & Annual Average (July 1983 - June 2005)Parameter: Air Temperature at 10 m Above The Surface Of The Earth (deg C)Internet: http://eosweb.larc.nasa.gov/sse/Note 1: SSE Methodology & Accuracy sections onlineNote 2: Lat/Lon values indicate the lower left corner of a 1x1 degree region. Negative values are south and west; Source U.S. National Aeronautics and Space Administration (NASA), Surface meteorology and Solar Energy (SSE) Date Released March 31st, 2009 (5 years ago) Date Updated April 01st, 2009 (5 years ago) Keywords average air temperature

147

A New Partial Sample Average Approximation Method for Chance ...  

E-Print Network (OSTI)

However, when ? is not small enough, e.g., 0.1, then the obtained solution ... In other words, for not small ...... constraints in hydro power reservoir management.

2014-10-13T23:59:59.000Z

148

Simulation of Radon Transport in Geothermal Reservoirs  

SciTech Connect

Numerical simulation of radon transport is a useful adjunct in the study of radon as an in situ tracer of hydrodynamic and thermodynamic numerical model has been developed to assist in the interpretation of field experiments. The model simulates transient response of radon concentration in wellhead geofluid as a function of prevailing reservoir conditions. The radon simulation model has been used to simulate radon concentration response during production drawdown and two flowrate transient tests in vapor-dominated systems. Comparison of model simulation with experimental data from field tests provides insight in the analysis of reservoir phenomena such as propagation of boiling fronts, and estimates of reservoir properties of porosity and permeability thickness.

Semprini, Lewis; Kruger, Paul

1983-12-15T23:59:59.000Z

149

Dispersivity as an oil reservoir rock characteristic  

SciTech Connect

The main objective of this research project is to establish dispersivity, {alpha}{sub d}, as an oil reservoir rock characteristic and to use this reservoir rock property to enhance crude oil recovery. A second objective is to compare the dispersion coefficient and the dispersivity of various reservoir rocks with other rock characteristics such as: porosity, permeability, capillary pressure, and relative permeability. The dispersivity of a rock was identified by measuring the physical mixing of two miscible fluids, one displacing the other in a porous medium. 119 refs., 27 figs., 12 tabs.

Menzie, D.E.; Dutta, S.

1989-12-01T23:59:59.000Z

150

Integrated reservoir characterization: Improvement in heterogeneities stochastic modelling by integration of additional external constraints  

SciTech Connect

The classical approach to construct reservoir models is to start with a fine scale geological model which is informed with petrophysical properties. Then scaling-up techniques allow to obtain a reservoir model which is compatible with the fluid flow simulators. Geostatistical modelling techniques are widely used to build the geological models before scaling-up. These methods provide equiprobable images of the area under investigation, which honor the well data, and which variability is the same than the variability computed from the data. At an appraisal phase, when few data are available, or when the wells are insufficient to describe all the heterogeneities and the behavior of the field, additional constraints are needed to obtain a more realistic geological model. For example, seismic data or stratigraphic models can provide average reservoir information with an excellent areal coverage, but with a poor vertical resolution. New advances in modelisation techniques allow now to integrate this type of additional external information in order to constrain the simulations. In particular, 2D or 3D seismic derived information grids, or sand-shale ratios maps coming from stratigraphic models can be used as external drifts to compute the geological image of the reservoir at the fine scale. Examples are presented to illustrate the use of these new tools, their impact on the final reservoir model, and their sensitivity to some key parameters.

Doligez, B.; Eschard, R. [Institut Francais du Petrole, Rueil Malmaison (France); Geffroy, F. [Centre de Geostatistique, Fontainebleau (France)] [and others

1997-08-01T23:59:59.000Z

151

A Measurement of Time-Averaged Aerosol Optical Depth using Air-Showers Observed in Stereo by HiRes  

E-Print Network (OSTI)

.F. Hanlon,1 C.M. Hoffman,2 M.H. Holzscheiter,2 G.A. Hughes,6 P. H¨untemeyer,1 C.C.H. Jui,1 M.A. Kirn,3 BZvi,5 D.R. Bergman,6 J.H. Boyer,4 C.T. Cannon,1 Z. Cao,1 B.M. Connolly,5 Y. Fedorova,1 C.B. Finley,5 W K. Reil,1 M.D. Roberts,8 S.R. Schnetzer,6 M. Seman,4 G. Sinnis,2 J.D. Smith,1 P. Sokolsky,1 C. Song

152

No. 221 / Thursday, November 15, 1990 / Rules and Regulations 47773 Yo = average tread depth after break-in, mils  

E-Print Network (OSTI)

after break-in, mils mc = the adjusted wear rate for the candidate tires as determined in accordance Alaska AGENCY: National Marine Fisheries Service (NMFS), NOAA, Commerce. ACTION: Final rule. SUMMARY, National Marine Fisheries Service, P.O. box 21668, Juneau, Alaska 99802-1668 (telephone: 907

153

Recommended Practice: Defense-in-Depth  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Report # INL/EXT-06-11478 Report # INL/EXT-06-11478 Control Systems Cyber Security: Defense in Depth Strategies May 2006 Prepared by Idaho National Laboratory Recommended Best Practice: Defense in Depth 2 Table of Contents Keywords............................................................................................................................. 3 Introduction......................................................................................................................... 3 Background ......................................................................................................................... 3 Overview of Contemporary Control System Architectures................................................. 4 Security Challenges in Control Systems .............................................................................

154

Naturally fractured tight gas reservoir detection optimization  

SciTech Connect

The work plan for October 1, 1997 to September 30, 1998 consisted of investigation of a number of topical areas. These topical areas were reported in four quarterly status reports, which were submitted to DOE earlier. These topical areas are reviewed in this volume. The topical areas covered during the year were: (1) Development of preliminary tests of a production method for determining areas of natural fracturing. Advanced Resources has demonstrated that such a relationship exists in the southern Piceance basin tight gas play. Natural fracture clusters are genetically related to stress concentrations (also called stress perturbations) associated with local deformation such a faulting. The mechanical explanation of this phenomenon is that deformation generally initiates at regions where the local stress field is elevated beyond the regional. (2) Regional structural and geologic analysis of the Greater Green River Basin (GGRB). Application of techniques developed and demonstrated during earlier phases of the project for sweet-spot delineation were demonstrated in a relatively new and underexplored play: tight gas from continuous-typeUpper Cretaceous reservoirs of the Greater Green River Basin (GGRB). The effort included data acquisition/processing, base map generation, geophysical and remote sensing analysis and the integration of these data and analyses. (3) Examination of the Table Rock field area in the northern Washakie Basin of the Greater Green River Basin. This effort was performed in support of Union Pacific Resources- and DOE-planned horizontal drilling efforts. The effort comprised acquisition of necessary seismic data and depth-conversion, mapping of major fault geometry, and analysis of displacement vectors, and the development of the natural fracture prediction. (4) Greater Green River Basin Partitioning. Building on fundamental fracture characterization work and prior work performed under this contract, namely structural analysis using satellite and potential field data, the GGRB was divided into partitions that will be used to analyze the resource potential of the Frontier and Mesaverde Upper Cretaceous tight gas play. A total of 20 partitions were developed, which will be instrumental for examining the Upper Cretaceous play potential. (5) Partition Analysis. Resource assessment associated with individual partitions was initiated starting with the Vermilion Sub-basin and the Green River Deep (which include the Stratos well) partitions (see Chapter 5). (6) Technology Transfer. Tech transfer was achieved by documenting our research and presenting it at various conferences.

NONE

1998-11-30T23:59:59.000Z

155

Heat deliverability of homogeneous geothermal reservoirs  

SciTech Connect

For the last two decades, the petroleum industry has been successfully using simple inflow performance relationships (IPR's) to predict oil deliverability. In contrast, the geothermal industry lacked a simple and reliable method to estimate geothermal wells' heat deliverability. To address this gap in the standard geothermal-reservoir-assessment arsenal, we developed generalized dimensionless geothermal inflow performance relationships (GIPR's). These ''reference curves'' may be regarded as an approximate general solution of the equations describing the practically important case of radial 2-phase inflow. Based on this approximate solution, we outline a straightforward approach to estimate the reservoir contribution to geothermal wells heat and mass deliverability for 2-phase reservoirs. This approach is far less costly and in most cases as reliable as numerically modeling the reservoir, which is the alternative for 2-phase inflow.

Iglesias, Eduardo R.; Moya, Sara L.

1991-01-01T23:59:59.000Z

156

Fifteenth workshop on geothermal reservoir engineering: Proceedings  

SciTech Connect

The Fifteenth Workshop on Geothermal Reservoir Engineering was held at Stanford University on January 23--25, 1990. Major topics included: DOE's geothermal research and development program, well testing, field studies, geosciences, geysers, reinjection, tracers, geochemistry, and modeling.

Not Available

1990-01-01T23:59:59.000Z

157

Study of induced seismicity for reservoir characterization  

E-Print Network (OSTI)

The main goal of the thesis is to characterize the attributes of conventional and unconventional reservoirs through passive seismicity. The dissertation is comprised of the development and applications of three new methods, ...

Li, Junlun, Ph. D. Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

158

Sediment resuspension in a monomictic eutrophic reservoir  

Science Journals Connector (OSTI)

During the mixing period sediment traps were placed at 9 different levels of the water column in La Concepcin reservoir (Mlaga-Spain). During the exposure time a benthic nepheloid layer with high suspended matt...

J. A. Glvez; F. X. Niell

1992-07-01T23:59:59.000Z

159

Sediment resuspension in a monomictic eutrophic reservoir  

Science Journals Connector (OSTI)

During the mixing period sediment traps were placed at 9 different levels of the water column in La Concepcin reservoir (Mlaga-Spain). During the exposure time a benthic nepheloid layer with high suspended matt...

J. A. Glvez; F. X. Niell

1992-01-01T23:59:59.000Z

160

Geothermal Reservoir Evaluation Considering Fluid Adsorption  

E-Print Network (OSTI)

SGP-"R- 68 Geothermal Reservoir Evaluation Considering Fluid Adsorption and Composition Michael J. Economides September, 1983 Financial support was provided through the Stanford Geothermal Program Contract No Geothermal Program Interdisciplinary Research in Engineering and Earth Sciences STANFORD UNIVERSITY Stanford

Stanford University

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Chelated Indium Activable Tracers for Geothermal Reservoirs  

E-Print Network (OSTI)

SGP-TR-99 Chelated Indium Activable Tracers for Geothermal Reservoirs Constantinos V. Chrysikopoulos Paul Kruger June 1986 Financial support was provided through the Stanford Geothermal Program under University Stanford Geothermal Program Interdisciplinary Research in Engineering and Earth Sciences STANFORD

Stanford University

162

ANNOTATED RESEARCH BIBLIOGRAPHY FOR GEOTHERMAL RESERVOIR ENGINEERING  

E-Print Network (OSTI)

Modeling f o r Geothermal Reservoirs and Power- plants. I'Fumaroles Hunt, 1970 Geothermal power James, 1978 FusionGood a lated perfo : Geothermal Power Systems Compared. 'I

Sudo!, G.A

2012-01-01T23:59:59.000Z

163

Modelling the GHG emission from hydroelectric reservoirs  

Science Journals Connector (OSTI)

A mechanistic model has been constructed to compute the fluxes of CO2 and CH4 emitted from the surface of hydroelectric reservoirs. The structure of the model has been designed to be adaptable to hydroelectric re...

Normand Thrien; Ken Morrison

2005-01-01T23:59:59.000Z

164

Reservoir fracture characterizations from seismic scattered waves  

E-Print Network (OSTI)

The measurements of fracture parameters, such as fracture orientation, fracture density and fracture compliance, in a reservoir is very important for field development and exploration. Traditional seismic methods for ...

Fang, Xinding

2012-01-01T23:59:59.000Z

165

Reservoir Data 6-30-09.xls  

NLE Websites -- All DOE Office Websites (Extended Search)

Injection MSL - Mean Sea Level Wl - Water Injection Muddy 2,829 (307) 261-5000 (888) 599-2200 Reservoir Data -- Rocky Mountain Oilfield Testing Center (RMOTC) -- NPR-3Teapot Dome...

166

Understanding the reservoir important to successful stimulation  

SciTech Connect

In anisotropic Bakken shale reservoirs, fracture treatments serve to extend the well bore radius past a disturbed zone and vertically connect discrete intervals. Natural fractures in the near-well bore area strongly control the well deliverability rate. The Bakken is one of the few shale formations in the world with commercial oil production. This article covers the Bakken reservoir properties that influence production and stimulation treatments. The concluding part will discuss the design and effectiveness of the treatments.

Cramer, D.D. (BJ Services Co., Denver, CO (US))

1991-04-22T23:59:59.000Z

167

Modeling well performance in compartmentalized gas reservoirs  

E-Print Network (OSTI)

index in estimating reservoir performance. The optimization routine is done with VBA using Excel solver. Model Assumptions The reservoir is in stabilized flow under pseudo-steady state conditions at constant pressure with no aquifer influx... is matched with a type curve to predict field performance. Fetkovich Decline Type Curves 11 is based on analytical solutions to flow equations for production at constant BHP and include both transient and boundary dominated flow periods. These log...

Yusuf, Nurudeen

2008-10-10T23:59:59.000Z

168

Modeling well performance in compartmentalized gas reservoirs  

E-Print Network (OSTI)

index in estimating reservoir performance. ? The optimization routine is done with VBA using Excel solver. Model Assumptions ? The reservoir is in stabilized flow under pseudo-steady state conditions at constant pressure with no aquifer influx... is matched with a type curve to predict field performance. Fetkovich Decline Type Curves 11 is based on analytical solutions to flow equations for production at constant BHP and include both transient and boundary dominated flow periods. These log...

Yusuf, Nurudeen

2009-05-15T23:59:59.000Z

169

Oil reservoir properties estimation using neural networks  

SciTech Connect

This paper investigates the applicability as well as the accuracy of artificial neural networks for estimating specific parameters that describe reservoir properties based on seismic data. This approach relies on JPL`s adjoint operators general purpose neural network code to determine the best suited architecture. The authors believe that results presented in this work demonstrate that artificial neural networks produce surprisingly accurate estimates of the reservoir parameters.

Toomarian, N.B. [California Inst. of Tech., Pasadena, CA (United States); Barhen, J.; Glover, C.W. [Oak Ridge National Lab., TN (United States). Center for Engineering Systems Advanced Research; Aminzadeh, F. [UNOCAL Corp., Sugarland, TX (United States)

1997-02-01T23:59:59.000Z

170

Play Analysis and Digital Portfolio of Major Oil Reservoirs in the Permian Basin: Application and Transfer of Advanced Geological and Engineering Technologies for Incremental Production Opportunities  

SciTech Connect

A play portfolio is being constructed for the Permian Basin in west Texas and southeast New Mexico, the largest onshore petroleum-producing basin in the United States. Approximately 1,300 reservoirs in the Permian Basin have been identified as having cumulative production greater than 1 MMbbl (1.59 x 10{sup 5} m{sup 3}) of oil through 2000. Of these significant-sized reservoirs, approximately 1,000 are in Texas and 300 in New Mexico. There are 32 geologic plays that have been defined for Permian Basin oil reservoirs, and each of the 1,300 major reservoirs was assigned to a play. The reservoirs were mapped and compiled in a Geographic Information System (GIS) by play. The final reservoir shapefile for each play contains the geographic location of each reservoir. Associated reservoir information within the linked data tables includes RRC reservoir number and district (Texas only), official field and reservoir name, year reservoir was discovered, depth to top of the reservoir, production in 2000, and cumulative production through 2000. Some tables also list subplays. Play boundaries were drawn for each play; the boundaries include areas where fields in that play occur but are smaller than 1 MMbbl (1.59 x 10{sup 5} m{sup 3}) of cumulative production. Oil production from the reservoirs in the Permian Basin having cumulative production of >1 MMbbl (1.59 x 10{sup 5} m{sup 3}) was 301.4 MMbbl (4.79 x 10{sup 7} m{sup 3}) in 2000. Cumulative Permian Basin production through 2000 was 28.9 Bbbl (4.59 x 10{sup 9} m{sup 3}). The top four plays in cumulative production are the Northwest Shelf San Andres Platform Carbonate play (3.97 Bbbl [6.31 x 10{sup 8} m{sup 3}]), the Leonard Restricted Platform Carbonate play (3.30 Bbbl [5.25 x 10{sup 8} m{sup 3}]), the Pennsylvanian and Lower Permian Horseshoe Atoll Carbonate play (2.70 Bbbl [4.29 x 10{sup 8} m{sup 3}]), and the San Andres Platform Carbonate play (2.15 Bbbl [3.42 x 10{sup 8} m{sup 3}]). Detailed studies of three reservoirs are in progress: Kelly-Snyder (SACROC unit) in the Pennsylvanian and Lower Permian Horseshoe Atoll Carbonate play, Fullerton in the Leonard Restricted Platform Carbonate play, and Barnhart (Ellenburger) in the Ellenburger Selectively Dolomitized Ramp Carbonate play. For each of these detailed reservoir studies, technologies for further, economically viable exploitation are being investigated.

Shirley P. Dutton; Eugene M. Kim; Ronald F. Broadhead; Caroline L. Breton; William D. Raatz; Stephen C. Ruppel; Charles Kerans

2004-01-13T23:59:59.000Z

171

Polarized electron beams at milliampere average current  

SciTech Connect

This contribution describes some of the challenges associated with developing a polarized electron source capable of uninterrupted days-long operation at milliAmpere average beam current with polarization greater than 80%. Challenges will be presented in the context of assessing the required level of extrapolation beyond the performance of today's CEBAF polarized source operating at ~ 200 uA average current. Estimates of performance at higher current will be based on hours-long demonstrations at 1 and 4 mA. Particular attention will be paid to beam-related lifetime-limiting mechanisms, and strategies to construct a photogun that operate reliably at bias voltage > 350kV.

Poelker, Matthew [JLAB

2013-11-01T23:59:59.000Z

172

Laser Fusion Energy The High Average Power  

E-Print Network (OSTI)

Laser Fusion Energy and The High Average Power Program John Sethian Naval Research Laboratory Dec for Inertial Fusion Energy with lasers, direct drive targets and solid wall chambers Lasers DPPSL (LLNL) Kr posters Snead Payne #12;Laser(s) Goals 1. Develop technologies that can meet the fusion energy

173

Ordered Weighted Average Based Fuzzy Rough Sets  

E-Print Network (OSTI)

Ordered Weighted Average Based Fuzzy Rough Sets Chris Cornelis 1 , Nele Verbiest1 , and Richard rough set model, which is based on a similar rationale, our proposal has the ad- vantage a feature selection application confirm the potential of the OWA-based model. Keywords: fuzzy rough sets

Gent, Universiteit

174

HIGH AVERAGE POWER OPTICAL FEL AMPLIFIERS.  

SciTech Connect

Historically, the first demonstration of the optical FEL was in an amplifier configuration at Stanford University [l]. There were other notable instances of amplifying a seed laser, such as the LLNL PALADIN amplifier [2] and the BNL ATF High-Gain Harmonic Generation FEL [3]. However, for the most part FELs are operated as oscillators or self amplified spontaneous emission devices. Yet, in wavelength regimes where a conventional laser seed can be used, the FEL can be used as an amplifier. One promising application is for very high average power generation, for instance FEL's with average power of 100 kW or more. The high electron beam power, high brightness and high efficiency that can be achieved with photoinjectors and superconducting Energy Recovery Linacs (ERL) combine well with the high-gain FEL amplifier to produce unprecedented average power FELs. This combination has a number of advantages. In particular, we show that for a given FEL power, an FEL amplifier can introduce lower energy spread in the beam as compared to a traditional oscillator. This properly gives the ERL based FEL amplifier a great wall-plug to optical power efficiency advantage. The optics for an amplifier is simple and compact. In addition to the general features of the high average power FEL amplifier, we will look at a 100 kW class FEL amplifier is being designed to operate on the 0.5 ampere Energy Recovery Linac which is under construction at Brookhaven National Laboratory's Collider-Accelerator Department.

BEN-ZVI, ILAN, DAYRAN, D.; LITVINENKO, V.

2005-08-21T23:59:59.000Z

175

Genetic Diversity in Microcystis Populations of a French Storage Reservoir Assessed by Sequencing of the 16S-23S rRNA  

E-Print Network (OSTI)

Genetic Diversity in Microcystis Populations of a French Storage Reservoir Assessed by Sequencing stations with different depths and at two dif- ferent sampling times (winter and summer) in the French allows this microorganism to growth in a broad range of environmental conditions. These papers

Jacquet, Stéphan

176

HYDROPOWER RESERVOIR FOR FLOOD CONTROL: A CASE STUDY ON RINGLET RESERVOIR, CAMERON  

E-Print Network (OSTI)

HYDROPOWER RESERVOIR FOR FLOOD CONTROL: A CASE STUDY ON RINGLET RESERVOIR, CAMERON HIGHLANDS, Malaysia 4 Professor, Department of Civil Engineering, Colorado State University, USA ABSTRACT: Hydropower as possible for daily hydropower generation as well as to prevent any spillage at dam. However

Julien, Pierre Y.

177

Cathode depth sensing in CZT detectors  

E-Print Network (OSTI)

Measuring the depth of interaction in thick Cadmium-Zinc-Telluride (CZT) detectors allows improved imaging and spectroscopy for hard X-ray imaging above 100 keV. The Energetic X-ray Imaging Survey Telescope (EXIST) will employ relatively thick (5 - 10 mm) CZT detectors, which are required to perform the broad energy-band sky survey. Interaction depth information is needed to correct events to the detector "focal plane" for correct imaging and can be used to improve the energy resolution of the detector at high energies by allowing event-based corrections for incomplete charge collection. Background rejection is also improved by allowing low energy events from the rear and sides of the detector to be rejected. We present experimental results of interaction depth sensing in a 5 mm thick pixellated Au-contact IMARAD CZT detector. The depth sensing was done by making simultaneous measurements of cathode and anode signals, where the interaction depth at a given energy is proportional to the ratio of cathode/anode signals. We demonstrate how a simple empirical formula describing the event distributions in the cathode/anode signal space can dramatically improve the energy resolution. We also estimate the energy and depth resolution of the detector as a function of the energy and the interaction depth. We also show a depth-sensing prototype system currently under development for EXIST in which cathode signals from 8, 16 or 32 crystals can be read-out by a small multi-channel ASIC board that is vertically edge-mounted on the cathode electrode along every second CZT crystal boundary. This allows CZT crystals to be tiled contiguously with minimum impact on throughput of incoming photons. The robust packaging is crucial in EXIST, which will employ very large area imaging CZT detector arrays.

J. Hong; E. C. Bellm; J. E. Grindlay; T. Narita

2003-10-16T23:59:59.000Z

178

Reservoir Characterization, Production Characteristics, and Research Needs for Fluvial/Alluvial Reservoirs in the United States  

SciTech Connect

The Department of Energy's (DOE's) Oil Recovery Field Demonstration Program was initiated in 1992 to maximize the economically and environmentally sound recovery of oil from known domestic reservoirs and to preserve access to this resource. Cost-shared field demonstration projects are being initiated in geology defined reservoir classes which have been prioritized by their potential for incremental recovery and their risk of abandonment. This document defines the characteristics of the fifth geological reservoir class in the series, fluvial/alluvial reservoirs. The reservoirs of Class 5 include deposits of alluvial fans, braided streams, and meandering streams. Deposit morphologies vary as a complex function of climate and tectonics and are characterized by a high degree of heterogeneity to fluid flow as a result of extreme variations in water energy as the deposits formed.

Cole, E.L.; Fowler, M.L.; Jackson, S.R.; Madden, M.P.; Raw-Schatzinger, V.; Salamy, S.P.; Sarathi, P.; Young, M.A.

1999-04-28T23:59:59.000Z

179

An Updated Conceptual Model Of The Los Humeros Geothermal Reservoir  

Open Energy Info (EERE)

Humeros Geothermal Reservoir Humeros Geothermal Reservoir (Mexico) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: An Updated Conceptual Model Of The Los Humeros Geothermal Reservoir (Mexico) Details Activities (0) Areas (0) Regions (0) Abstract: An analysis of production and reservoir engineering data of 42 wells from the Los Humeros geothermal field (Mexico) allowed obtaining the pressure and temperature profiles for the unperturbed reservoir fluids and developing 1-D and 2-D models for the reservoir. Results showed the existence of at least two reservoirs in the system: a relatively shallow liquid-dominant reservoir located between 1025 and 1600 m above sea level (a.s.l.) the pressure profile of which corresponds to a 300-330°C boiling water column and a deeper low-liquid-saturation reservoir located between

180

Reservoir characterization of the Mississippian Ratcliffe, Richland County, Montana, Williston Basin. Topical report, September 1997  

SciTech Connect

This topical report is a compilation of characterizations by different disciplines of the Mississippian Ratcliffe in portions of Richland County, MT. Goals of the report are to increase understanding of the reservoir rocks, oil-in-place, heterogeneity and methods for improved recovery. The report covers investigations of geology, petrography, reservoir engineering and seismic. The Ratcliffe is a low permeability oil reservoir which appears to be developed across much of the study area and occurs across much of the Williston Basin. The reservoir has not been a primary drilling target in the study area because average reserves have been insufficient to payout the cost of drilling and completion despite the application of hydraulic fracture stimulation. Oil trapping does not appear to be structurally controlled. For the Ratcliffe to be a viable drilling objective, methods need to be developed for (1) targeting better reservoir development and (2) better completions. A geological model is presented for targeting areas with greater potential for commercial reserves in the Ratcliffe. This model can be best utilized with the aid of 3D seismic. A 3D seismic survey was acquired and is used to demonstrate a methodology for targeting the Ratcliffe. Other data obtained during the project include oriented core, special formation-imaging log, pressure transient measurements and oil PVT. Although re-entry horizontal drilling was unsuccessfully tested, this completion technology should improve the economic viability of the Ratcliffe. Reservoir simulation of horizontal completions with productivity of three times that of a vertical well suggested two or three horizontal wells in a 258-ha (640-acre) area could recover sufficient reserves for profitable drilling.

Sippel, M.; Luff, K.D.; Hendricks, M.L.

1998-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

E-Print Network 3.0 - advanced reservoir characterization Sample...  

NLE Websites -- All DOE Office Websites (Extended Search)

<< < 1 2 3 4 5 > >> 1 TEXAS A&M UNIVERSITY Reservoir Geophysics Program Summary: and fracture analysis, multi-component seismic reservoir characterization, quantitative reservoir...

182

Surfactant-enhanced spontaneous imbibition process in highly fractured carbonate reservoirs.  

E-Print Network (OSTI)

??Highly fractured carbonate reservoirs are a class of reservoirs characterized by high conductivity fractures surrounding low permeability matrix blocks. In these reservoirs, wettability alteration is (more)

Chen, Peila

2011-01-01T23:59:59.000Z

183

Analysis of Field Development Strategies of CO2 EOR/Capture Projects Using a Reservoir Simulation Economic Model  

E-Print Network (OSTI)

($) Drilling cost for one well ($) Facilities cost for one pattern ($) Tubing cost for one well ($) Drilling depth (feet) EIA US Energy Information Administration EOR Enhanced Oil Recovery EOS Equation of State IEA International... in the reservoir ................................................................ 20 Figure 13: Scope of this chapter: definition of the economic model ............................... 21 Figure 14: Spot price of the oil on the WTI market from 1986 to 2013 (EIA...

Saint-Felix, Martin

2013-05-03T23:59:59.000Z

184

Sources Of Average Individual Radiation Exposure  

NLE Websites -- All DOE Office Websites (Extended Search)

Of Average Individual Radiation Exposure Of Average Individual Radiation Exposure Natural background Medical Consumer products Industrial, security, educational and research Occupational 0.311 rem 0.300 rem 0.013 rem 0.0003 rem 0.0005 rem Savannah River Nuclear Solutions, LLC, provides radiological protection services and oversight at the Savannah River Site (SRS). These services include radiation dose measurements for persons who enter areas where they may be exposed to radiation or radioactive material. The results are periodically reported to monitored individuals. The results listed are based on a radiation dose system developed by the International Commission on Radiation Protection. The system uses the terms "effective dose," "equivalent dose" and units of rem. You may be more familiar with the term "millirem" (mrem), which is 1/1000 of a rem.

185

Fat turnover in obese slower than average  

NLE Websites -- All DOE Office Websites (Extended Search)

9-04 9-04 For immediate release: 09/23/2011 | NR-11-09-04 Fat turnover in obese slower than average Anne M Stark, LLNL, (925) 422-9799, stark8@llnl.gov Printer-friendly This scanning electron micrograph image shows part of a lobule of adipose tissue (body fat). Adipose tissue is specialized connective tissue that functions as the major storage site for fat. Photo courtesy of David Gregory & Debbie Marshall/Wellcome Images LIVERMORE, Calif. -- It may be more difficult for obese people to lose fat because the "turnover" rate is much slower for those overweight than average weight individuals. New research in the Sept. 25 online edition of the journal Nature shows that the turnover (storage and loss rate) of fat in the human body is about 1 1/2 years compared to fat cells, which turnover about every 10 years,

186

Natural Gas Prices: Well Above Recent Averages  

Gasoline and Diesel Fuel Update (EIA)

5 5 Notes: The recent surge in spot prices at the Henry Hub are well above a typical range for 1998-1999 (in this context, defined as the average, +/- 2 standard deviations). Past price surges have been of short duration. The possibility of a downward price adjustment before the end of next winter is a source of considerable risk for storage operators who acquire gas at recent elevated prices. Storage levels in the Lower 48 States were 7.5 percent below the 5-year average (1995-1999) by mid-August (August 11), although the differential is only 6.4 percent in the East, which depends most heavily on storage to meet peak demand. Low storage levels are attributable, at least in part, to poor price incentives: high current prices combined with only small price

187

Indirect CP violation results and HFAG averages  

E-Print Network (OSTI)

The current status of the search for indirect CP violation in the neutral D meson system at the B-factories and at LHCb is reported. The indirect CP asymmetry search is performed by the measurement of the proper-time asymmetry ($A_{\\Gamma}$) in decays of $D^0-\\bar{D^0}$ mesons to CP eigenstates, $K^-K^+$ and $\\pi^- \\pi^+$, and by $y_{CP}$, the ratio between the effective lifetime measured in decay to a CP eigenstate and that to the mixed eigenstate $K \\pi$. All results are consistent with the no CP violation hypothesis. The latest world averages for mixing and CP asymmetry in the charm sector evaluated by the Heavy Flavour Averaging Group are presented. The no mixing hypothesis is excluded at more than 12 standard deviations. The search for direct and indirect CP violation in the charm sector is consistent with no CP violation at 2.0% confident level.

Silvia Borghi

2013-12-17T23:59:59.000Z

188

Polarized electron beams at milliampere average current  

SciTech Connect

This contribution describes some of the challenges associated with developing a polarized electron source capable of uninterrupted days-long operation at milliAmpere average beam current with polarization greater than 80%. Challenges will be presented in the context of assessing the required level of extrapolation beyond the performance of todays CEBAF polarized source operating at ? 200 uA average current. Estimates of performance at higher current will be based on hours-long demonstrations at 1 and 4 mA. Particular attention will be paid to beam-related lifetime-limiting mechanisms, and strategies to construct a photogun that operate reliably at bias voltage > 350kV.

Poelker, M. [Thomas Jefferson National Accelerator Facility, Newport News, Virginia 23606 (United States)

2013-11-07T23:59:59.000Z

189

Integral cesium reservoir: Design and transient operation  

SciTech Connect

An electrically heated thermionic converter has been designed built and successfully tested in air (Homer et.al., 1995). One of the unique features of this converter was an integral cesium reservoir thermally coupled to the emitter. The reservoir consisted of fifteen cesiated graphite pins located in pockets situated in the emitter lead with thermal coupling to the emitter, collector and the emitter terminal; there were no auxiliary electric heaters on the reservoir. Test results are described for conditions in which the input thermal power to the converter was ramped up and down between 50% and 100% of full power in times as short as 50 sec, with data acquisition occurring every 12 sec. During the ramps the emitter and collector temperature profiles. the reservoir temperature and the electric output into a fixed load resistor are reported. The converter responded promptly to the power ramps without excessive overshoot and with no tendency to develop instabilities. This is the rust demonstration of the performance of a cesium-graphite integral reservoir in a fast transient

Smith, J.N. Jr.; Horner, M.H.; Begg, L.L. [General Atomics, San Diego, CA (United States); Wrobleski, W.J. [Westinghouse Electric Corp., West Mifflin, PA (United States). Bettis Atomic Power Lab.

1995-01-01T23:59:59.000Z

190

Analysis of Langley optical depth data, with aerosol and gas retrievals,  

NLE Websites -- All DOE Office Websites (Extended Search)

Analysis of Langley optical depth data, with aerosol and gas retrievals, Analysis of Langley optical depth data, with aerosol and gas retrievals, for the RSS 103 instrument in Barrow, Alaska Gianelli, Scott Columbia University - NASA/GISS Lacis, Andrew NASA/Goddard Institute for Space Studies Carlson, Barbara NASA/Goddard Institute for Space Studies Category: Aerosols Bimodal aerosol retrievals, and high-resolution retrevals of nitrogen dioxide, are performed on the Langley optical depth data from the RSS 103 device that was situated in Barrow, Alaska between March and August in 1999. The results show a higher fine mode aerosol optical depth on average than was retrieved by the RSS 102 at the SGP site. The seasonal cycle is also reversed with high values at Barrow occurring in the spring and low values in the summer. The fine mode effective radius also appears to

191

D-optimal design for Rapid Assessment Model of CO2 flooding in high water cut oil reservoirs  

Science Journals Connector (OSTI)

Abstract Most of major oilfields in China have reached high water cut stage, but still, they contribute to more than 70% of domestic oil production. How to extract more oil from mature oilfields has become a hot topic in petroleum engineering. Carbon dioxide flooding is a winwin strategy because it can enhance oil recovery and simultaneously reduce CO2 emissions into the atmosphere. In order to evaluate the potentials of CO2 flooding in high water cut oil reservoirs, various 3-D heterogeneous geological models were built based on Guan 104 fault block in Dagang Oilfield to perform reservoir simulations. The D-optimal design was applied to build and verify the Rapid Assessment Model of CO2 flooding in high water cut oil reservoirs. Five quantitative variables were considered, including average horizontal permeability, permeability variation coefficient, ratio of vertical to horizontal permeability, net thickness of formation and percentage of recoverable reserves by water flooding. The process of weighting emphasized the contributions of linear terms, quadratic terms and first-order interactions of five quantitative parameters to improved recovery factor and Net Present Value of CO2 flooding. Using the Rapid Assessment Model of CO2 flooding in high water cut oil reservoirs, significant first-order interactions were sorted out and type curves were established and analyzed for the evaluation of technical and economic efficiency of CO2 flooding in high water cut oil reservoirs. Aimed at oil reservoirs with the similar geological conditions and fluid properties as Guan 104 fault block, the Rapid Assessment Model and type curves of CO2 flooding in high water cut oil reservoirs can be applied to predict improved recovery factor and Net Present Value of water-alternating-CO2 flooding at different conditions of reservoir parameters and development parameter. The approach could serve as a guide for the application and spread of CO2-EOR projects.

Zhaojie Song; Zhiping Li; Chunsheng Yu; Jirui Hou; Mingzhen Wei; Baojun Bai; Yunpeng Hu

2014-01-01T23:59:59.000Z

192

Inversion of reservoir quality: An example from the Triassic Buntsandstein, offshore Netherlands  

SciTech Connect

Sandstones from the Triassic Main Buntsandstein form a major gas reservoir in the Netherlands offshore. The sequence is dominated by siliciclastics deposited in an arid continental setting, and include dune, interdune, sheetsand, and fluvial sandstones. Reduction in reservoir quality is caused primarily by dolomite, halite, and anhydrite cementation, with minor authigenic illite and chlorite. Integration of petrographic and isotopic data has allowed the origins and relative timing of the different cements to be constrained. The carbon and oxygen isotopic composition of dolomite ([delta][sup 13]C = -3.76 to -9.3%, [delta][sup 18]O = -3 to +2.9% PDB) combined with strontium isotopic data (0.7091 to 0.7109 [sup 86]Sr/[sup 87]Sr) suggest that is precipitated from meteoric groundwater. Halite and anhydrite formed from a mixture of meteoric water and saline fluids expelled from underlying evaporites and claystones. Sulfur isotopic data (+4.2 to +12.1 CDT) support6 this interpretation for the origin of the anhydrite. Precipitation of the major authigenic minerals occurred during early diagenesis, prior to burial depths of 500 m. Cementation and groundwater flow followed the zones of highest permeability and caused an inversion of reservoir quality. Sandstones with the highest depositional porosity and permeability (i.e., dune sandstones) are the most cemented, and have poorer reservoir quality compared to the fluvial and interdune sandstones, which originally had lower depositional porosity/permeability. Formation of authigenic illite and chlorite occurred during burial and has significantly reduced permeability. Information on the depositional settings and paleogeography, combined with expected groundwater flow, has helped define potential exploration areas of reduced reservoir quality as a result of extensive early cementation.

Purvis, K.; Okkerman, J. (Koninklijke/Shell Exploratie en Producktie Laboratorium, Rijswijk (Netherlands))

1993-09-01T23:59:59.000Z

193

Shale Reservoir Characterization | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oil & Gas » Shale Gas » Shale Reservoir Oil & Gas » Shale Gas » Shale Reservoir Characterization Shale Reservoir Characterization Geologist examining the base of the Marcellus Shale at an outcrop near Bedford, PA. Geologist examining the base of the Marcellus Shale at an outcrop near Bedford, PA. Gas-producing shales are predominantly composed of consolidated clay-sized particles with a high organic content. High subsurface pressures and temperatures convert the organic matter to oil and gas, which may migrate to conventional petroleum traps and also remains within the shale. However, the clay content severely limits gas and fluid flow within the shales. It is, therefore, necessary to understand the mineral and organic content, occurrence of natural fractures, thermal maturity, shale volumes, porosity

194

Magic Reservoir Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Magic Reservoir Geothermal Area Magic Reservoir Geothermal Area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Magic Reservoir Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (0) 9 Exploration Activities (0) 10 References Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"TERRAIN","zoom":6,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"500px","height":"300px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":43.32833333,"lon":-114.3983333,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

195

New method for evaluating composite reservoir systems  

SciTech Connect

A simple new technique has been developed for evaluating interference test data in radially symmetric composite reservoirs. The technique is based on the realization that systematic variations in the apparent storage coefficient (calculated from semi-log analysis of the late-time data are indicative of a two-mobility (k/..mu..) reservoir. By analyzing variations in the apparent storage coefficient, both the mobility and size of the inner region can be calculated. The technique is particularly useful for evaluating heterogeneous geothermal systems where the intersection of several faults, or hydrothermal alteration has created a high permeability region in the center of the geothermal field. The technique is applied to an extensive interference test in the geothermal reservoir at Klamath Falls, Oregon. 7 refs., 7 figs.

Benson, S.M.; Lai, C.H.

1985-03-01T23:59:59.000Z

196

Characterization of oil and gas reservoir heterogeneity  

SciTech Connect

Research described In this report addresses the internal architecture of two specific reservoir types: restricted-platform carbonates and fluvial-deltaic sandstones. Together, these two reservoir types contain more than two-thirds of the unrecovered mobile oil remaining ill Texas. The approach followed in this study was to develop a strong understanding of the styles of heterogeneity of these reservoir types based on a detailed outcrop description and a translation of these findings into optimized recovery strategies in select subsurface analogs. Research targeted Grayburg Formation restricted-platform carbonate outcrops along the Algerita Escarpment and In Stone Canyon In southeastern New Mexico and Ferron deltaic sandstones in central Utah as analogs for the North Foster (Grayburg) and Lake Creek (Wilcox) units, respectively. In both settings, sequence-stratigraphic style profoundly influenced between-well architectural fabric and permeability structure. It is concluded that reservoirs of different depositional origins can therefore be categorized Into a heterogeneity matrix'' based on varying intensity of vertical and lateral heterogeneity. The utility of the matrix is that it allows prediction of the nature and location of remaining mobile oil. Highly stratified reservoirs such as the Grayburg, for example, will contain a large proportion of vertically bypassed oil; thus, an appropriate recovery strategy will be waterflood optimization and profile modification. Laterally heterogeneous reservoirs such as deltaic distributary systems would benefit from targeted infill drilling (possibly with horizontal wells) and improved areal sweep efficiency. Potential for advanced recovery of remaining mobile oil through heterogeneity-based advanced secondary recovery strategies In Texas is projected to be an Incremental 16 Bbbl. In the Lower 48 States this target may be as much as 45 Bbbl at low to moderate oil prices over the near- to mid-term.

Tyler, N.; Barton, M.D.; Bebout, D.G.; Fisher, R.S.; Grigsby, J.D.; Guevara, E.; Holtz, M.; Kerans, C.; Nance, H.S.; Levey, R.A.

1992-10-01T23:59:59.000Z

197

Water salinity of the First Eocene reservoir: Its unique behaviour and influence on reservoir engineering calculations  

SciTech Connect

The salinity of the produced water from First Eocene reservoir of Wafra field was studied through its past history. The change in the salinity of the initially produced water (from about 500 to 20,000 ppm NaCl) was attributed to the meteoric water which might have entered the reservoir through its outcrops to the west of the field. The correct value of the connate water salinity (23,000 ppm) that should be used in estimating the original oil in place by the volumetric method was determined by three different approaches. In addition, a technique to be followed in calculating the volumetric original oil in place for the First Eocene reservoir is outlined to overcome the complex behaviour of aquifer salinity. The change in the produced water salinity of the First Eocene reservoir with time was studied and proved that water is dumping from an upper water bearing zone into First Eocene reservoir. Upper water dumping, which apparently has supported the reservoir pressure, was confirmed to occur behind casing in many deeper wells penetrating the First Eocene reservoir by the analysis of their temperature and noise logs.

Ghoniem, S.A.A.; Al-Zanki, F.H.

1985-03-01T23:59:59.000Z

198

Water salinity of First Eocene reservoir: Unique behavior and influence on reservoir engineering calculations  

SciTech Connect

The salinity of the produced water from the First Eocene reservoir of the Wafra field was studied through its history. The change in the salinity of the initially produced water (from about 500 to 20,000 ppm NaCl) was attributed to meteoric water that might have entered the reservoir through outcrops west of the field. The correct value of the interstitial water salinity (23,000ppm) that should be used in estimating the original oil in place (OOIP) by the volumetric method was determined by three different approaches. In addition, a technique to overcome the complex behavior of aquifer salinity in calculating the volumetric OOIP for the First Eocene reservoir is outlined. A study of the change in the produced water salinity of the First Eocene reservoir with time proved that water is dumping from an upper water-bearing zone into the reservoir. Analysis of temperature and noise logs confirmed that this upper water dumping, which apparently has supported the reservoir pressure, occurred behind casing in many deeper wells penetrating the First Eocene reservoir.

Ghoniem, S.A.; Al-Zanki, F.H.

1987-09-01T23:59:59.000Z

199

Prediction of Kizildere reservoir behavior under exploitation  

SciTech Connect

Kizildere geothermal reservoir is under exploitation since 1984. During the four years of operation, electricity production showed a decline from the initially designed power output of 20.4 MW{sub e}. The scaling in wells necessitates periodic mechanical cleaning. However decline in well flow rates even after cleaning, indicate either decrease in productivity index due to scaling in fractures or due to rapid decline in reservoir pressure due to insufficient recharge and strong interference between wells. In this paper the results of a lumped parameter model prepared for Kizildere will be presented with the analysis of natural state of the field.

Okandan, Ender

1988-01-01T23:59:59.000Z

200

Pesticide use in Kentucky reservoir watershed  

SciTech Connect

This report summarizes information on the types, uses, and amounts of pesticides applied to Kentucky Reservoir and its immediate watershed. Estimates for the quantities and types of the various pesticides used are based primarily on the land uses in the watershed. A listing of commonly used pesticides is included describing their uses, mode of action, and potential toxicological effects. This report will inform the the public and the Kentucky Reservoir Water Resources Task Force of the general extent of pesticide usage and is not an assessment of pesticide impacts. 10 refs., 5 figs., 9 tabs.

Butkus, S.R.

1988-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Geothermal reservoir engineering code: comparison and validation  

SciTech Connect

INTERCOMP has simulated six geothermal reservoir problems. INTERCOMP's geothermal reservoir model was used for all problems. No modifications were made to this model except to provide tabular output of the simulation results in the units used in RFP No. DE-RP03-80SF-10844. No difficulty was encountered in performing the problems described herein, although setting up the boundary and grid conditions exactly as specified were sometimes awkward, and minor modifications to the grid system were necessitated. The results of each problem are presented in tabular and (for many) graphical form.

Not Available

1981-02-27T23:59:59.000Z

202

Improved characterization of reservoir behavior by integration of reservoir performances data and rock type distributions  

SciTech Connect

An integrated geological/petrophysical and reservoir engineering study was performed for a large, mature waterflood project (>250 wells, {approximately}80% water cut) at the North Robertson (Clear Fork) Unit, Gaines County, Texas. The primary goal of the study was to develop an integrated reservoir description for {open_quotes}targeted{close_quotes} (economic) 10-acre (4-hectare) infill drilling and future recovery operations in a low permeability, carbonate (dolomite) reservoir. Integration of the results from geological/petrophysical studies and reservoir performance analyses provide a rapid and effective method for developing a comprehensive reservoir description. This reservoir description can be used for reservoir flow simulation, performance prediction, infill targeting, waterflood management, and for optimizing well developments (patterns, completions, and stimulations). The following analyses were performed as part of this study: (1) Geological/petrophysical analyses: (core and well log data) - {open_quotes}Rock typing{close_quotes} based on qualitative and quantitative visualization of pore-scale features. Reservoir layering based on {open_quotes}rock typing {close_quotes} and hydraulic flow units. Development of a {open_quotes}core-log{close_quotes} model to estimate permeability using porosity and other properties derived from well logs. The core-log model is based on {open_quotes}rock types.{close_quotes} (2) Engineering analyses: (production and injection history, well tests) Material balance decline type curve analyses to estimate total reservoir volume, formation flow characteristics (flow capacity, skin factor, and fracture half-length), and indications of well/boundary interference. Estimated ultimate recovery analyses to yield movable oil (or injectable water) volumes, as well as indications of well and boundary interference.

Davies, D.K.; Vessell, R.K. [David K. Davies & Associates, Kingwood, TX (United States); Doublet, L.E. [Texas A& M Univ., College Station, TX (United States)] [and others

1997-08-01T23:59:59.000Z

203

INCREASING WATERFLOOD RESERVES IN THE WILMINGTON OIL FIELD THROUGH IMPROVED RESERVOIR CHARACTERIZATION AND RESERVOIR MANAGEMENT  

SciTech Connect

This project increased recoverable waterflood reserves in slope and basin reservoirs through improved reservoir characterization and reservoir management. The particular application of this project is in portions of Fault Blocks IV and V of the Wilmington Oil Field, in Long Beach, California, but the approach is widely applicable in slope and basin reservoirs. Transferring technology so that it can be applied in other sections of the Wilmington Field and by operators in other slope and basin reservoirs is a primary component of the project. This project used advanced reservoir characterization tools, including the pulsed acoustic cased-hole logging tool, geologic three-dimensional (3-D) modeling software, and commercially available reservoir management software to identify sands with remaining high oil saturation following waterflood. Production from the identified high oil saturated sands was stimulated by recompleting existing production and injection wells in these sands using conventional means as well as a short radius redrill candidate. Although these reservoirs have been waterflooded over 40 years, researchers have found areas of remaining oil saturation. Areas such as the top sand in the Upper Terminal Zone Fault Block V, the western fault slivers of Upper Terminal Zone Fault Block V, the bottom sands of the Tar Zone Fault Block V, and the eastern edge of Fault Block IV in both the Upper Terminal and Lower Terminal Zones all show significant remaining oil saturation. Each area of interest was uncovered emphasizing a different type of reservoir characterization technique or practice. This was not the original strategy but was necessitated by the different levels of progress in each of the project activities.

Scott Walker; Chris Phillips; Roy Koerner; Don Clarke; Dan Moos; Kwasi Tagbor

2002-02-28T23:59:59.000Z

204

Absolute Approximation of Tukey Depth: Theory and Experiments  

E-Print Network (OSTI)

Absolute Approximation of Tukey Depth: Theory and Experiments Dan Chen School of Computer Science¨ur Theoretische Informatik Abstract A Monte Carlo approximation algorithm for the Tukey depth problem in high. Keywords: Tukey depth, computational geometry 1. Introduction Tukey depth is also known as location depth

Morin, Pat

205

Average resonance capture study of Te124  

Science Journals Connector (OSTI)

An average resonance capture study of Te124 was carried out by bombarding samples of Te123 with 2- and 24-keV neutron beams. The complete set of 0+, 1+, 2+ states disclosed by the experiment is consistent with the data of Robinson, Hamilton, and Snelling, demonstrating that there are no undetected states of these spins (especially 0+ states) below about 2500 keV. In particular, proposed 0+ levels at 1156 and 1290 keV are ruled out. This impacts various attempted interpretations in terms of intruder states, U(5), and O(6) symmetries.

R. F. Casten; J.-Y. Zhang; B.-C. Liao

1991-07-01T23:59:59.000Z

206

Scale-dependent gas hydrate saturation estimates in sand reservoirs in the Ulleung Basin, East Sea of Korea  

Science Journals Connector (OSTI)

Through the use of 2-D and 3-D seismic data, several gas hydrate prospects were identified in the Ulleung Basin, East Sea of Korea and thirteen drill sites were established and logging-while-drilling (LWD) data were acquired from each site in 2010. Sites UBGH26 and UBGH210 were selected to test a series of high amplitude seismic reflections, possibly from sand reservoirs. LWD logs from the UBGH26 well indicate that there are three significant sand reservoirs with varying thickness. Two upper sand reservoirs are water saturated and the lower thinly bedded sand reservoir contains gas hydrate with an average saturation of 13%, as estimated from the P-wave velocity. The well logs at the UBGH26 well clearly demonstrated the effect of scale-dependency on gas hydrate saturation estimates. Gas hydrate saturations estimated from the high resolution LWD acquired ring resistivity (vertical resolution of about 58cm) reaches about 90% with an average saturation of 28%, whereas gas hydrate saturations estimated from the low resolution A40L resistivity (vertical resolution of about 120cm) reaches about 25% with an average saturation of 11%. However, in the UBGH210 well, gas hydrate occupies a 5-m thick sand reservoir near 135mbsf with a maximum saturation of about 60%. In the UBGH210 well, the average and a maximum saturation estimated from various well logging tools are comparable, because the bed thickness is larger than the vertical resolution of the various logging tools. High resolution wireline log data further document the role of scale-dependency on gas hydrate calculations.

M.W. Lee; T.S. Collett

2013-01-01T23:59:59.000Z

207

Colorado Dry Natural Gas New Reservoir Discoveries in Old Fields...  

Annual Energy Outlook 2012 (EIA)

New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Colorado Dry Natural Gas New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Decade Year-0 Year-1 Year-2...

208

Feasibility of waterflooding Soku E7000 gas-condensate reservoir  

E-Print Network (OSTI)

We performed a simple 3D compositional reservoir simulation study to examine the possibility of waterflooding the Soku E7 gas-condensate reservoir. This study shows that water injection results in higher condensate recovery than natural depletion...

Ajayi, Arashi

2012-06-07T23:59:59.000Z

209

Evaluating human fecal contamination sources in Kranji Reservoir Catchment, Singapore  

E-Print Network (OSTI)

Singapore government through its Public Utilities Board is interested in opening Kranji Reservoir to recreational use. However, water courses within the Kranji Reservoir catchment contain human fecal indicator bacteria ...

Nshimyimana, Jean Pierre

2010-01-01T23:59:59.000Z

210

U.S. Coalbed Methane Proved Reserves New Reservoir Discoveries...  

U.S. Energy Information Administration (EIA) Indexed Site

New Reservoir Discoveries in Old Fields (Billion Cubic Feet) U.S. Coalbed Methane Proved Reserves New Reservoir Discoveries in Old Fields (Billion Cubic Feet) Decade Year-0 Year-1...

211

Optimal Hydropower Reservoir Operation with Environmental Requirements MARCELO ALBERTO OLIVARES  

E-Print Network (OSTI)

Optimal Hydropower Reservoir Operation with Environmental Requirements By MARCELO ALBERTO OLIVARES Engineering Optimal Hydropower Reservoir Operation with Environmental Requirements Abstract Engineering solutions to the environmental impacts of hydropower operations on downstream aquatic ecosystem are studied

Lund, Jay R.

212

FMI Borehole Geology, Geomechanics and 3D Reservoir Modeling...  

Open Energy Info (EERE)

Geomechanics and 3D Reservoir Modeling Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: FMI Borehole Geology, Geomechanics and 3D Reservoir Modeling...

213

Reducing temperature uncertainties by stochastic geothermal reservoir modelling  

Science Journals Connector (OSTI)

......economically successful geothermal reservoirs. To this...An increased use of geothermal energy requires reliable estimates...exploration and development of geothermal reservoirs. Suitable...risk of failure and cost may be reduced and estimated......

C. Vogt; D. Mottaghy; A. Wolf; V. Rath; R. Pechnig; C. Clauser

2010-04-01T23:59:59.000Z

214

Optimizing Development Strategies to Increase Reserves in Unconventional Gas Reservoirs  

E-Print Network (OSTI)

spacing in highly uncertain and risky unconventional gas reservoirs. To achieve the research objectives, an integrated reservoir and decision modeling tool that fully incorporates uncertainty was developed. Monte Carlo simulation was used with a fast...

Turkarslan, Gulcan

2011-10-21T23:59:59.000Z

215

Monitoring and Modeling Fluid Flow in a Developing EGS Reservoir  

Energy.gov (U.S. Department of Energy (DOE))

Project objectives: Better understand and model fluid injection into a tight reservoir on the edges of a hydrothermal field. Use seismic data to constrain geomechanical/hydrologic/thermal model of reservoir.

216

Average Price of Natural Gas Production  

Gasoline and Diesel Fuel Update (EIA)

. . Quantity and Average Price of Natural Gas Production in the United States, 1930-1996 (Volumes in Million Cubic Feet, Prices in Dollars per Thousand Cubic Feet) Table Year Gross Withdrawals Used for Repressuring Nonhydro- carbon Gases Removed Vented and Flared Marketed Production Extraction Loss Dry Production Average Wellhead Price of Marketed Production 1930 ....................... NA NA NA NA 1,978,911 75,140 1,903,771 0.08 1931 ....................... NA NA NA NA 1,721,902 62,288 1,659,614 0.07 1932 ....................... NA NA NA NA 1,593,798 51,816 1,541,982 0.06 1933 ....................... NA NA NA NA 1,596,673 48,280 1,548,393 0.06 1934 ....................... NA NA NA NA 1,815,796 52,190 1,763,606 0.06 1935 ....................... NA NA NA NA 1,968,963 55,488 1,913,475 0.06 1936 ....................... 2,691,512 73,507 NA 392,528 2,225,477

217

Average values and dispersion (in parentheses)  

NLE Websites -- All DOE Office Websites (Extended Search)

Average values and dispersion (in parentheses) Average values and dispersion (in parentheses) Base-pair Parameters --------------------------------------------------------------------------------------- Shear Stretch Stagger Buckle Propeller Opening 3DNA A 0.01(0.23) -0.18(0.10) 0.02(0.25) -0.13(7.77) -11.79(4.14) 0.57(2.80) B 0.00(0.21) -0.15(0.12) 0.09(0.19) 0.53(6.74) -11.35(5.26) 0.63(3.05) CEHS A 0.01(0.23) -0.18(0.10) 0.02(0.25) -0.13(7.75) -11.82(4.14) 0.56(2.78) B 0.00(0.21) -0.14(0.12) 0.09(0.19) 0.53(6.73) -11.37(5.27) 0.62(3.03) CompDNA A 0.01(0.23) -0.18(0.10) 0.02(0.25) -0.12(7.70) -11.81(4.14) 0.56(2.79) B 0.00(0.21) -0.15(0.12) 0.09(0.19) 0.53(6.70) -11.37(5.26) 0.62(3.03) Curves A 0.01(0.23) -0.18(0.10) 0.02(0.25) -0.13(7.85) -11.76(4.12) 0.57(2.80)

218

PLAY ANALYSIS AND DIGITAL PORTFOLIO OF MAJOR OIL RESERVOIRS IN THE PERMIAN BASIN: APPLICATION AND TRANSFER OF ADVANCED GEOLOGICAL AND ENGINEERING TECHNOLOGIES FOR INCREMENTAL PRODUCTION OPPORTUNITIES  

SciTech Connect

The Permian Basin of west Texas and southeast New Mexico has produced >30 Bbbl (4.77 x 10{sup 9} m{sup 3}) of oil through 2000, most of it from 1,339 reservoirs having individual cumulative production >1 MMbbl (1.59 x 10{sup 5} m{sup 3}). These significant-sized reservoirs are the focus of this report. Thirty-two Permian Basin oil plays were defined, and each of the 1,339 significant-sized reservoirs was assigned to a play. The reservoirs were mapped and compiled in a Geographic Information System (GIS) by play. Associated reservoir information within linked data tables includes Railroad Commission of Texas reservoir number and district (Texas only), official field and reservoir name, year reservoir was discovered, depth to top of the reservoir, production in 2000, and cumulative production through 2000. Some tables also list subplays. Play boundaries were drawn for each play; the boundaries include areas where fields in that play occur but are <1 MMbbl (1.59 x 10{sup 5} m{sup 3}) of cumulative production. This report contains a summary description of each play, including key reservoir characteristics and successful reservoir-management practices that have been used in the play. The CD accompanying the report contains a pdf version of the report, the GIS project, pdf maps of all plays, and digital data files. Oil production from the reservoirs in the Permian Basin having cumulative production >1 MMbbl (1.59 x 10{sup 5} m{sup 3}) was 301.4 MMbbl (4.79 x 10{sup 7} m{sup 3}) in 2000. Cumulative Permian Basin production through 2000 from these significant-sized reservoirs was 28.9 Bbbl (4.59 x 10{sup 9} m{sup 3}). The top four plays in cumulative production are the Northwest Shelf San Andres Platform Carbonate play (3.97 Bbbl [6.31 x 10{sup 8} m{sup 3}]), the Leonard Restricted Platform Carbonate play (3.30 Bbbl 5.25 x 10{sup 8} m{sup 3}), the Pennsylvanian and Lower Permian Horseshoe Atoll Carbonate play (2.70 Bbbl [4.29 x 10{sup 8} m{sup 3}]), and the San Andres Platform Carbonate play (2.15 Bbbl [3.42 x 10{sup 8} m{sup 3}]).

Shirley P. Dutton; Eugene M. Kim; Ronald F. Broadhead; Caroline L. Breton; William D. Raatz; Stephen C. Ruppel; Charles Kerans

2004-05-01T23:59:59.000Z

219

Techniques of High Performance Reservoir Simulation for Unconventional Challenges  

E-Print Network (OSTI)

48 offshore Alaska 2010 5 high performance computing, execution of compositional simulation in parallel seems to be the apparently feasible way to tackle its computational demand. Although running reservoir simulation in parallel sounds extremely... attractive, developing an efficient parallel reservoir simulator is far more challenging than developing the underlying serial reservoir simulator. For decades there have remained many open problems associated with high performance computing and reservoir...

Wang, Yuhe

2013-12-05T23:59:59.000Z

220

Laboratory study of acid stimulation of drilling-mud-damaged geothermal-reservoir materials. Final report  

SciTech Connect

Presented here are the results of laboratory testing performed to provide site specific information in support of geothermal reservoir acidizing programs. The testing program included laboratory tests performed to determine the effectiveness of acid treatments in restoring permeability of geologic materials infiltrated with hydrothermally altered sepiolite drilling mud. Additionally, autoclave tests were performed to determine the degree of hydrothermal alteration and effects of acid digestion on drilling muds and drill cuttings from two KGRA's. Four laboratory scale permeability/acidizing tests were conducted on specimens prepared from drill cuttings taken from two geothermal formations. Two tests were performed on material from the East Mesa KGRA Well No. 78-30, from a depth of approximately 5500 feet, and two tests were performed on material from the Roosevelt KGRA Well No. 52-21, from depths of approximately 7000 to 7500 feet. Tests were performed at simulated in situ geothermal conditions of temperature and pressure.

Not Available

1983-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Semi-analytical solutions for multilayer reservoirs  

E-Print Network (OSTI)

, we develop, validate, and present five new approximate solutions for the case of a multilayer reservoir system - these solutions are: [ Solution p[wDj(tD)] Description 1 a[j] Constant p[wDj(tD)] Case 2 a[j tD] Linear p[wDj(tD)] Zero...

Lolon, Elyezer Pabibak

2012-06-07T23:59:59.000Z

222

STIMULATION AND RESERVOIR ENGINEERING OF GEOTHERMAL RESOURCXS  

E-Print Network (OSTI)

STIMULATION AND RESERVOIR ENGINEERING OF GEOTHERMAL RESOURCXS Henry J. Ramey, Jr., and A. Louis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Stanford Geothermal Project Reports . . . . . . . . . . . . . . 69 Papers Presented a t the Second United Nations Symposium on t h e Development and Use of Geothermal Resources, May 19-29, 1975, San

Stanford University

223

Fourteenth workshop geothermal reservoir engineering: Proceedings  

SciTech Connect

The Fourteenth Workshop on Geothermal Reservoir Engineering was held at Stanford University on January 24--26, 1989. Major areas of discussion include: (1) well testing; (2) various field results; (3) geoscience; (4) geochemistry; (5) reinjection; (6) hot dry rock; and (7) numerical modelling. For these workshop proceedings, individual papers are processed separately for the Energy Data Base.

Ramey, H.J. Jr.; Kruger, P.; Horne, R.N.; Miller, F.G.; Brigham, W.E.; Cook, J.W.

1989-01-01T23:59:59.000Z

224

Fourteenth workshop geothermal reservoir engineering: Proceedings  

SciTech Connect

The Fourteenth Workshop on Geothermal Reservoir Engineering was held at Stanford University on January 24--26, 1989. Major areas of discussion include: (1) well testing; (2) various field results; (3) geoscience; (4) geochemistry; (5) reinjection; (6) hot dry rock; and (7) numerical modelling. For these workshop proceedings, individual papers are processed separately for the Energy Data Base.

Ramey, H.J. Jr.; Kruger, P.; Horne, R.N.; Miller, F.G.; Brigham, W.E.; Cook, J.W.

1989-12-31T23:59:59.000Z

225

Underground natural gas storage reservoir management  

SciTech Connect

The objective of this study is to research technologies and methodologies that will reduce the costs associated with the operation and maintenance of underground natural gas storage. This effort will include a survey of public information to determine the amount of natural gas lost from underground storage fields, determine the causes of this lost gas, and develop strategies and remedial designs to reduce or stop the gas loss from selected fields. Phase I includes a detailed survey of US natural gas storage reservoirs to determine the actual amount of natural gas annually lost from underground storage fields. These reservoirs will be ranked, the resultant will include the amount of gas and revenue annually lost. The results will be analyzed in conjunction with the type (geologic) of storage reservoirs to determine the significance and impact of the gas loss. A report of the work accomplished will be prepared. The report will include: (1) a summary list by geologic type of US gas storage reservoirs and their annual underground gas storage losses in ft{sup 3}; (2) a rank by geologic classifications as to the amount of gas lost and the resultant lost revenue; and (3) show the level of significance and impact of the losses by geologic type. Concurrently, the amount of storage activity has increased in conjunction with the net increase of natural gas imports as shown on Figure No. 3. Storage is playing an ever increasing importance in supplying the domestic energy requirements.

Ortiz, I.; Anthony, R.

1995-06-01T23:59:59.000Z

226

Type curve analysis for naturally fractured reservoirs (infinite-acting reservoir case): a new approach  

E-Print Network (OSTI)

analysis methods are sometimes inconclusive for pressure transient analysis of wells completed in naturally fractured reservoirs. This is due to wellbore storage effects which mask the early time "straight-line" that is expected on the semilog plot...

Angel Restrepo, Juan Alejandro

2012-06-07T23:59:59.000Z

227

Reservoir Simulation for Improving Water Flooding Performance in Low-Permeability Reservoirs  

Science Journals Connector (OSTI)

We studied the YSL oil field in Daqing, China with reservoir permeability 10-3 ?m2 that has been developed by water flooding. From the results of a preliminary estimate ... we have used as the basis for numerical...

Huiying Zhong; Hongjun Yin

2013-07-01T23:59:59.000Z

228

Maximizing output from oil reservoirs without water breakthrough  

E-Print Network (OSTI)

Maximizing output from oil reservoirs without water breakthrough S.K. Lucas School of Mathematics, revised May 2003, published 45(3), 2004, 401­422 Abstract Often in oil reservoirs a layer of water lies, for example, Muskat [8], Bear [1]). When oil is removed from the reservoir by an oil well, it will generate

Lucas, Stephen

229

Parallel Finite Element Simulation of Tracer Injection in Oil Reservoirs  

E-Print Network (OSTI)

Parallel Finite Element Simulation of Tracer Injection in Oil Reservoirs Alvaro L.G.A. Coutinho In this work, parallel finite element techniques for the simulation of tracer injection in oil reservoirs. Supercomputers have made it possible to consider global reservoir effects which can not be represented using

Coutinho, Alvaro L. G. A.

230

Analysis of reservoir performance and forecasting for the eastern area of the C-2 Reservoir, Lake Maracaibo, Venezuela  

E-Print Network (OSTI)

This research developed a numerical simulation based on the latest reservoir description to evaluate the feasibility of new infill wells to maximize the recovery specifically in the eastern region of the reservoir operated by Petroleos de Venezuela...

Urdaneta Anez, Jackeline C

2001-01-01T23:59:59.000Z

231

Genesis field, Gulf of Mexico: Recognizing reservoir compartments on geologic and production time scales in deep-water reservoirs  

Science Journals Connector (OSTI)

...Factors for the Pleistocene Reservoirs of Genesis Field Reservoir EOD Reserves (MMBOE) Recovery Factor () Drive Mechanism Completions...49-63 Weak water drive 5 All completions are fracture packed. EOD environment of deposition. Table 2 Cumulative Production and...

Michael L. Sweet; Larry T. Sumpter

232

Average deployments versus missile and defender parameters  

SciTech Connect

This report evaluates the average number of reentry vehicles (RVs) that could be deployed successfully as a function of missile burn time, RV deployment times, and the number of space-based interceptors (SBIs) in defensive constellations. Leakage estimates of boost-phase kinetic-energy defenses as functions of launch parameters and defensive constellation size agree with integral predictions of near-exact calculations for constellation sizing. The calculations discussed here test more detailed aspects of the interaction. They indicate that SBIs can efficiently remove about 50% of the RVs from a heavy missile attack. The next 30% can removed with two-fold less effectiveness. The next 10% could double constellation sizes. 5 refs., 7 figs.

Canavan, G.H.

1991-03-01T23:59:59.000Z

233

Characterization and reservoir evaluation of a hydraulically fractured, shaly gas reservoir  

E-Print Network (OSTI)

, Shaly Gas Reservoir. ( December 1991 ) Cesar Alfonso Santiago Molina, Ingeniero de Petroleos, Universidad Nacional de Colombia; Chair of Advisory Committee: Dr. Steven W. Poston Shale content in reservoir rocks affect their petrophysical properties... for their support. The author also wishes to express his deepest appreciation to Dr. H. Chen for all the help and suggestions he made in this study. The author expresses his gratitude to every one in Empresa Colombiana de Petroleos, Ecopetrol, who made possible...

Santiago Molina, Cesar Alfonso

1991-01-01T23:59:59.000Z

234

PublicationsmailagreementNo.40014024 maximum depth  

E-Print Network (OSTI)

and a video camera to complete installation of the world's first regional cabled ocean observatory. NEPTUNE- tion systems that--using power and the internet--provide continuous, long-term monitoring of oceanPublicationsmailagreementNo.40014024 THE 2.7km maximum depth beneath the ocean surface of neptune

Pedersen, Tom

235

3-D description of fracture surfaces and stress-sensitivity analysis for naturally fractured reservoirs  

SciTech Connect

Three kinds of reservoir cores (limestone, sandstone, and shale with natural fractures) were used to study the effect of morphology of fracture surfaces on stress sensitivity. The cores, obtained from the reservoirs with depths of 2170 to 2300 m, have fractures which are mated on a large scale, but unmated on a fine scale. A specially designed photoelectric scanner with a computer was used to describe the topography of the fracture surfaces. Then, theoretical analysis of the fracture closure was carried out based on the fracture topography generated. The scanning results show that the asperity has almost normal distributions for all three types of samples. For the tested samples, the fracture closure predicted by the elastic-contact theory is different from the laboratory measurements because plastic deformation of the aspirates plays an important role under the testing range of normal stresses. In this work, the traditionally used elastic-contact theory has been modified to better predict the stress sensitivity of reservoir fractures. Analysis shows that the standard deviation of the probability density function of asperity distribution has a great effect on the fracture closure rate.

Zhang, S.Q.; Jioa, D.; Meng, Y.F.; Fan, Y.

1997-08-01T23:59:59.000Z

236

Influences of salt structures on reservoir rocks in block L-2, Dutch continental shelf  

SciTech Connect

In the subsurface of the Netherlands Continental Shelf, thick layers of Zechstein salt have developed into salt domes and ridges that pierce through the overlying formations. To measure the range of lateral influence of the salt in these structures on the sandstone reservoir rocks of the Mesozoic sequence, a cementation model was developed. The target area, Block L-2, was chosen for the presence of salt domes, wells, and reservoir rocks. The L-2 case study has been performed on two Triassic sandstone intervals. The lower, Volpriehausen, sandstone showed halite cementation in one well, located within several 100 m from a salt dome. Four other wells, located more than 1.5 km from a salt structure, did not show any signs of halite cementation. Therefore, the lateral influence of salt domes on the surrounding reservoir rock is, in this case, limited to less than 1.5 km at 3-4 km depth. A slightly shallower Triassic sandstone (Detfurth) shows more frequent halite cementation. This cementation can be attributed to early seepage from overlying Rot salt brines.Triassic Rot salt is present above depletion areas of the Zechstein salt structures, and in such a way the seepage can be seen as an indirect influence of the salt structures.

Dronkert, H. (Delft Univ. of Technology, Delft (Netherlands)); Remmelts, G. (Geological Survey of the Netherlands, Haarlem (Netherlands))

1993-09-01T23:59:59.000Z

237

Thermal analysis of the ATI thermionic converter for optimum cesium reservoir location  

SciTech Connect

A first-order thermal analysis was performed on the emitter lead region of the Advanced Thermionic Initiative (ATI) Thermionic Fuel Element (TFE) design. The lead region is the candidate location for a metal-matrix, cesium-graphite reservoir to supply cesium vapor to the thermionic converter. The cesium pressure developed is dependent upon the temperature and cesium-carbon equilibrium reaction of the reservoir. Steady-state, one dimensional conduction, with thermal radiation losses and Joulean heat generation, was used to calculate the temperature distribution in the non-fueled lead region. This temperature distribution was linked to the ATI reactor core design through the integration of axial emitter temperature distributions for the maximum, minimum, and average power TFE fuel pins. The axial temperature distribution in the emitter lead region was found to be most pronounced for the maximum power fuel element and least pronounced for the minimum power TFE.

Young, T.J. (Aerospace Power Division, Wright Laboratory/POOC, Wright-Patterson AFB, Ohio 45433-6563 (United States)); Thayer, K.L.; Ramalingam, M.L. (UES, Inc., 4401 Dayton-Xenia Road, Dayton, Ohio 45432-1894 (United States))

1993-01-15T23:59:59.000Z

238

Fuel Economy Standards, New Vehicle Sales, and Average Fuel Efficiency  

Science Journals Connector (OSTI)

The average fuel efficiency of new automobiles sold in the ... trend stagnated in 1981, however, and average fuel efficiency has actually fallen since 1987. Corporate Average Fuel Economy (CAFE) standardsthe maj...

Steven G. Thorpe

1997-05-01T23:59:59.000Z

239

Fact #744: September 10, 2012 Average New Light Vehicle Price...  

Energy Savers (EERE)

4: September 10, 2012 Average New Light Vehicle Price Grows Faster than Average Used Light Vehicle Price Fact 744: September 10, 2012 Average New Light Vehicle Price Grows Faster...

240

STATE OF CALIFORNIA AREA WEIGHTED AVERAGE CALCULATION WORKSHEET: RESIDENTIAL  

E-Print Network (OSTI)

be used to calculate weight-averaged U-factors or averaged SHGC values for prescriptive envelope of window (the SHGC values of skylights cannot be averaged per §151(f)4A). a. "Area" can be replaced

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Geotechnical studies of geothermal reservoirs | Open Energy Information  

Open Energy Info (EERE)

Geotechnical studies of geothermal reservoirs Geotechnical studies of geothermal reservoirs Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report: Geotechnical studies of geothermal reservoirs Details Activities (7) Areas (7) Regions (0) Abstract: It is proposed to delineate the important factors in the geothermal environment that will affect drilling. The geologic environment of the particular areas of interest are described, including rock types, geologic structure, and other important parameters that help describe the reservoir and overlying cap rock. The geologic environment and reservoir characteristics of several geothermal areas were studied, and drill bits were obtained from most of the areas. The geothermal areas studied are: (1) Geysers, California, (2) Imperial Valley, California, (3) Roosevelt Hot

242

Integrated Reflection Seismic Monitoring and Reservoir Modeling for Geologic CO2 Sequestration  

SciTech Connect

The US DOE/NETL CCS MVA program funded a project with Fusion Petroleum Technologies Inc. (now SIGMA) to model the proof of concept of using sparse seismic data in the monitoring of CO{sub 2} injected into saline aquifers. The goal of the project was to develop and demonstrate an active source reflection seismic imaging strategy based on deployment of spatially sparse surface seismic arrays. The primary objective was to test the feasibility of sparse seismic array systems to monitor the CO{sub 2} plume migration injected into deep saline aquifers. The USDOE/RMOTC Teapot Dome (Wyoming) 3D seismic and reservoir data targeting the Crow Mountain formation was used as a realistic proxy to evaluate the feasibility of the proposed methodology. Though the RMOTC field has been well studied, the Crow Mountain as a saline aquifer has not been studied previously as a CO{sub 2} sequestration (storage) candidate reservoir. A full reprocessing of the seismic data from field tapes that included prestack time migration (PSTM) followed by prestack depth migration (PSDM) was performed. A baseline reservoir model was generated from the new imaging results that characterized the faults and horizon surfaces of the Crow Mountain reservoir. The 3D interpretation was integrated with the petrophysical data from available wells and incorporated into a geocellular model. The reservoir structure used in the geocellular model was developed using advanced inversion technologies including Fusion's ThinMAN{trademark} broadband spectral inversion. Seal failure risk was assessed using Fusion's proprietary GEOPRESS{trademark} pore pressure and fracture pressure prediction technology. CO{sub 2} injection was simulated into the Crow Mountain with a commercial reservoir simulator. Approximately 1.2MM tons of CO{sub 2} was simulated to be injected into the Crow Mountain reservoir over 30 years and subsequently let 'soak' in the reservoir for 970 years. The relatively small plume developed from this injection was observed migrating due to gravity to the apexes of the double anticline in the Crow Mountain reservoir of the Teapot dome. Four models were generated from the reservoir simulation task of the project which included three saturation models representing snapshots at different times during and after simulated CO{sub 2} injection and a fully saturated CO{sub 2} fluid substitution model. The saturation models were used along with a Gassmann fluid substitution model for CO{sub 2} to perform fluid volumetric substitution in the Crow Mountain formation. The fluid substitution resulted in a velocity and density model for the 3D volume at each saturation condition that was used to generate a synthetic seismic survey. FPTI's (Fusion Petroleum Technologies Inc.) proprietary SeisModelPRO{trademark} full acoustic wave equation software was used to simulate acquisition of a 3D seismic survey on the four models over a subset of the field area. The simulated acquisition area included the injection wells and the majority of the simulated plume area.

John Rogers

2011-12-31T23:59:59.000Z

243

Fact #849: December 1, 2014 Midsize Hybrid Cars Averaged 51%...  

Energy Savers (EERE)

average is the production-weighted harmonic mean. 2014 data are preliminary. Fact 849 Dataset Supporting Information Average Fuel Economy of New Midsize Cars - Hybrid vs....

244

Evaluating oil quality and monitoring production from heavy oil reservoirs using geochemical methods: Application to the Boscan Field, Venezuela  

SciTech Connect

Many oil fields worldwide contain heavy oil in one or more reservoir units. The low gravity of these oils is most frequently due to biodegradation and/or low maturity. The challenge is to find ways to economically recover this oil. Methods which reduce the operating costs of producing heavy oil add significant value to such projects. Geochemical techniques which use the composition of the reservoir fluids as natural tracers offer cost effective methods to assist with reservoir management. The low viscosity and gravity of heavy oil, combined with frequent high water cuts, low flow rates, and the presence of downhole artificial lift equipment, make many conventional production logging methods difficult to apply. Therefore, monitoring production, especially if the produced oil is commingled from multiple reservoirs, can be difficult. Geochemical methods can be used to identify oil/water contacts, tubing string leaks and to allocate production to individual zones from commingled production. An example of a giant heavy oil field where geochemical methods may be applicable is the Boscan Field in Venezuela. Low maturity oil, averaging 10{degrees} API gravity, is produced from the Eocene Upper and Lower Boscan (Miosa) Sands. Geochemical, stratigraphic and engineering data have helped to better define the controls on oil quality within the field, identified new reservoir compartments and defined unique characteristics of the Upper and Lower Boscan oils. This information can be used to identify existing wells in need of workovers due to mechanical problems and to monitor production from new infill wells.

Kaufman, R.L.; Noguera, V.H.; Bantz, D.M. [Chevron Overseas Petroleum, San Ramon, CA (United States); Rodriguez, R. [Maraven, S.A., Caracas (Venezuela)

1996-08-01T23:59:59.000Z

245

Heavy oil reservoirs recoverable by thermal technology. Annual report  

SciTech Connect

This volume contains reservoir, production, and project data for target reservoirs which contain heavy oil in the 8 to 25/sup 0/ API gravity range and are susceptible to recovery by in situ combustion and steam drive. The reservoirs for steam recovery are less than 2500 feet deep to comply with state-of-the-art technology. In cases where one reservoir would be a target for in situ combustion or steam drive, that reservoir is reported in both sections. Data were collectd from three source types: hands-on (A), once-removed (B), and twice-removed (C). In all cases, data were sought depicting and characterizing individual reservoirs as opposed to data covering an entire field with more than one producing interval or reservoir. The data sources are listed at the end of each case. This volume also contains a complete listing of operators and projects, as well as a bibliography of source material.

Kujawa, P.

1981-02-01T23:59:59.000Z

246

Multicomponent 3-D characterization of a coalbed methane reservoir  

SciTech Connect

Methane is produced from fractured coalbed reservoirs at Cedar Hill Field in the San Juan Basin. Fracturing and local stress are critical to production because of the absence of matrix permeability in the coals. Knowledge of the direction of open fractures, the degree of fracturing, reservoir pressure, and compartmentalization is required to understand the flow of fluids through the reservoir. A multicomponent 3-D seismic survey was acquired to aid in coalbed methane reservoir characterization. Coalbed reservoir heterogeneities, including isolated pressure cells, zones of increased fracture density, and variable fracture directions, have been interpreted through the analysis of the multicomponent data and integration with petrophysical and reservoir engineering studies. Strike-slip faults, which compartmentalize the reservoir, have been identified by structural interpretation of the 3-D P-wave seismic data. These faults form boundaries for pressure cells that have been identified by P-wave reflection amplitude anomalies.

Shuck, E.L. [Advance Geophysical Corp., Englewood, CO (United States)] [Advance Geophysical Corp., Englewood, CO (United States); Davis, T.L.; Benson, R.D. [Colorado School of Mines, Golden, CO (United States). Geophysics Dept.] [Colorado School of Mines, Golden, CO (United States). Geophysics Dept.

1996-03-01T23:59:59.000Z

247

Development of reservoir simulator for hydraulically fractured gas wells in noncontinuous lenticular reservoirs  

SciTech Connect

A mathematical model is presented which forms the basis for a reservoir simulator that can be used to assist in the interpretation and prediction of the performance of hydraulically fractured gas wells completed in the western tight sands area. The model represents a first step in developing a reservoir simulator that can be used as an exploration tool and to analyze proposed gas well tests and future production trends in noncontinuous sand lense formations which are representative of the tight gas sands located in the Rocky Mountain gas provinces. The model developed consists of the necessary mathematical equations to simulate both reservoir and well performance under a variety of operating conditions. The equations developed are general in that they consider the following effects: (1) three-dimensional flow in the reservoir and one-dimensional flow in the fracture; (2) non-Darcy flow in the reservoir and fracture; (3) wellbore and fracture storage; (4) formation damage on the fracture face; (5) frictional pressure drop in the production string; (6) noncontinuous sand lenses; and (7) Klinkenberg effect. As a start toward the development of the final version of the desired reservoir simulator, a two-dimensional simulator was secured, placed on the computer, and debugged, and some test cases were run to ensure its validity. Using this simulator as a starting point, changes to reflect the effects of items 3 and 6 were made since it was believed these were the more important effects to consider at this stage of development. The development of an operational two-dimensional gas reservoir simulator was completed. Further work will be required to extend the simulator to three dimensions and incorporate all the changes reflected in items 1 to 6.

Evans, R.D.; Carroll, H.B. Jr.

1980-10-01T23:59:59.000Z

248

Evaluation of CO2 enhanced oil recovery and sequestration potential in low permeability reservoirs, Yanchang Oilfield, China  

Science Journals Connector (OSTI)

Abstract Sequestrating CO2 in reservoirs can substantially enhance oil recovery and effectively reduce greenhouse gas emission. To evaluate the potential of CO2 enhanced oil recovery (EOR) and sequestration for Yanchang Oilfield in China, a screening standard which was suitable for CO2-EOR and sequestration in Yanchang Oilfield was proposed based on its characteristics of strong heterogeneity, high water content and severe fluid channeling after water flooding. In addition, an efficient calculation method stream tube simulation method was presented to figure out CO2 sequestration coefficient and oil recovery factor. After screening and evaluating, it turned out that 148 out of 176 blocks in 22 oilfields were suitable for CO2-EOR and sequestration. CO2 flooding after water flooding can produce 180.21נ106t more crude oil and sequestrate 223.38נ106t CO2. The average incremental oil recovery rate of miscible reservoirs was 12.49% and the average CO2 sequestration coefficient was 0.27t/t while the two values were 6.83% and 0.18t/t for immiscible reservoirs. There are comparatively more reservoirs that are suitable for CO2-EOR and sequestration in Yanchang Oilfield than normal, which can obviously enhance oil recovery and means a great potential for CO2 sequestration. CO2-EOR and sequestration in Yanchang Oilfield has a bright application prospect.

D.F. Zhao; X.W. Liao; D.D. Yin

2014-01-01T23:59:59.000Z

249

Fast neutron background measurements at shallow depths  

SciTech Connect

We report on measurements of the neutron backgrounds for neutrino experiments at shallow depth (such as the proposed San Onofre neutrino oscillation experiment). A detector capable of pulse-shape discrimination measured the flux of fast neutrons at 20 mwe depth in the Stanford Underground Facility to be (1.07 {+-} 0.30) X 10{sup -6} cm{sup -2} s{sup -1}. An experiment, situated in the Tendon Gallery of the San Onofre Unit 2 reactor. studied spallation neutrons from muons traversing Pb and Cu. An underground experiment in the SUF, employing a detector filled with Gd-loaded liquid scintillator, is measuring the neutron production rate and multiplicity for muon spallation in low-A material (hydrocarbon-based liquid scintillator).

Chen, M.; Hertenberger, R.; Novikov, V. [Inst. of Nuclear Research, Moscow (Russian Federation); Dougherty, B.

1993-10-01T23:59:59.000Z

250

Property:Depth(m) | Open Energy Information  

Open Energy Info (EERE)

Depth(m) Depth(m) Jump to: navigation, search This is a property of type String. Pages using the property "Depth(m)" Showing 25 pages using this property. (previous 25) (next 25) 1 1.5-ft Wave Flume Facility + 0.9 + 10-ft Wave Flume Facility + 1.5 + 11-ft Wave Flume Facility + 1.8 + 2 2-ft Flume Facility + 1.8 + 3 3-ft Wave Flume Facility + 0.9 + 5 5-ft Wave Flume Facility + 1.5 + 6 6-ft Wave Flume Facility + 1.8 + A Alden Large Flume + 3.0 + Alden Small Flume + 1.8 + Alden Tow Tank + 1.2 + Alden Wave Basin + 1.2 + B Breakwater Research Facility + 0.8 + Bucknell Hydraulic Flume + 0.6 + C Carderock 2-ft Variable Pressure Cavitation Water Tunnel + 0.6 + Carderock 3-ft Variable Pressure Cavitation Water Tunnel + 0.7 + Carderock Circulating Water Channel + 2.7 +

251

Quantification of Libby Reservoir Levels Needed to Maintain or Enhance Reservoir Fisheries, 1983-1987 Methods and Data Summary.  

SciTech Connect

Libby Reservoir was created under an International Columbia River Treaty between the United States and Canada for cooperative water development of the Columbia River Basin. The authorized purpose of the dam is to provide power, flood control, and navigation and other benefits. Research began in May 1983 to determine how operations of Libby dam impact the reservoir fishery and to suggest ways to lessen these impacts. This study is unique in that it was designed to accomplish its goal through detailed information gathering on every trophic level in the reservoir system and integration of this information into a quantitative computer model. The specific study objectives are to: quantify available reservoir habitat, determine abundance, growth and distribution of fish within the reservoir and potential recruitment of salmonids from Libby Reservoir tributaries within the United States, determine abundance and availability of food organisms for fish in the reservoir, quantify fish use of available food items, develop relationships between reservoir drawdown and reservoir habitat for fish and fish food organisms, and estimate impacts of reservoir operation on the reservoir fishery. 115 refs., 22 figs., 51 tabs.

Chisholm, Ian

1989-12-01T23:59:59.000Z

252

Secondary natural gas recovery in mature fluvial sandstone reservoirs, Frio Formation, Agua Dulce Field, South Texas  

SciTech Connect

An approach that integrates detailed geologic, engineering, and petrophysical analyses combined with improved well-log analytical techniques can be used by independent oil and gas companies of successful infield exploration in mature Gulf Coast fields that larger companies may consider uneconomic. In a secondary gas recovery project conducted by the Bureau of Economic Geology and funded by the Gas Research Institute and the U.S. Department of Energy, a potential incremental natural gas resource of 7.7 bcf, of which 4.0 bcf may be technically recoverable, was identified in a 490-ac lease in Agua Dulce field. Five wells in this lease had previously produced 13.7 bcf from Frio reservoirs at depths of 4600-6200 ft. The pay zones occur in heterogeneous fluvial sandstones offset by faults associated with the Vicksburg fault zone. The compartments may each contain up to 1.0 bcf of gas resources with estimates based on previous completions and the recent infield drilling experience of Pintas Creek Oil Company. Uncontacted gas resources occur in thin (typically less than 10 ft) bypassed zones that can be identified through a computed log evaluation that integrates open-hole logs, wireline pressure tests, fluid samples, and cores. At Agua Dulce field, such analysis identified at 4-ft bypassed zone uphole from previously produced reservoirs. This reservoir contained original reservoir pressure and flowed at rates exceeding 1 mmcf/d. The expected ultimate recovery is 0.4 bcf. Methodologies developed in the evaluation of Agua Dulce field can be successfully applied to other mature gas fields in the south Texas Gulf Coast. For example, Stratton and McFaddin are two fields in which the secondary gas recovery project has demonstrated the existence of thin, potentially bypassed zones that can yield significant incremental gas resources, extending the economic life of these fields.

Ambrose, W.A.; Levey, R.A. (Univ. of Texas, Austin, TX (United States)); Vidal, J.M. (ResTech, Inc., Houston, TX (United States)); Sippel, M.A. (Research and Engineering Consultants, Inc., Englewood, CA (United States)); Ballard, J.R. (Envirocorp Services and Technology, Houston, TX (United States)); Coover, D.M. Jr. (Pintas Creek Oil Company, Corpus Christi, TX (United States)); Bloxsom, W.E. (Coastal Texas Oil and Gas, Houston, TX (United States))

1993-09-01T23:59:59.000Z

253

Enhancing Reservoir Management in the Appalach  

NLE Websites -- All DOE Office Websites (Extended Search)

Reservoir Management in the Appalachian Basin by Identifying Technical Reservoir Management in the Appalachian Basin by Identifying Technical Barrier and Preferred Practices Final Report Reporting Period Start Date: September 1, 2001 Reporting Period End Date: September 15, 2003 Principal Author(s): Ronald R. McDowell Khashayar Aminian Katharine L. Avary John M. Bocan Michael Ed. Hohn Douglas G. Patchen September 2003 DE-FC26-01BC15273 West Virginia University Research Corporation West Virginia Geological and Economic Survey (subcontractor) ii DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus,

254

Chapter 5 - Coal Composition and Reservoir Characterization  

Science Journals Connector (OSTI)

Abstract Coal consists of organic and mineral matter. Fixed carbon from organic matter measures the energy output of coal during combustion. Mineral matter determines how coal responds to combustion and affects reservoir porosity and permeability. Minerals infill pores, cleats, or fractures and replace the organic composition of coal. Organic composition is grouped into maceral association as microlithotypes and macrolithotypes, the latter for megascopic field descriptions (e.g. coal cores and mine face). Coal composition controls reservoir properties such as gas adsorption capacity, gas content, porosity, and permeability. Permeability is important to gas transport from coal matrix pores to the production well. Coal permeability is a function of the width, length, and height of cleats or fractures as well as the aperture, spacing, frequency or density, and connectivity of cleats or fractures. Coal cleats or fractures formed during burial, compaction, and coalification (endogenetic) and after coalification during deformation, uplift, and erosion of the basin of deposition.

Romeo M. Flores

2014-01-01T23:59:59.000Z

255

The impact of water depth on safety and environmental performance in offshore oil and gas production  

Science Journals Connector (OSTI)

This paper reports on an empirical analysis of company-reported incidents on oil and gas production platforms in the Gulf of Mexico between 1996 and 2010. During these years, there was a dramatic increase in the water depths at which offshore oil and gas is extracted. Controlling for platform characteristics such as age, quantity of oil and gas produced, and number of producing wells, we find that incidents (such as blowouts, injuries, and oil spills) are positively correlated with deeper water. Controlling for these and other characteristics, for an average platform, each 100 feet of added depth increases the probability of a company-reported incident by 8.5%. While further research into the causal connections between water depth and platform risks is warranted, this study highlights the potential value of increased monitoring of deeper water platforms.

Lucija Muehlenbachs; Mark A. Cohen; Todd Gerarden

2013-01-01T23:59:59.000Z

256

Contour Charts of SOFAR Speed and Axis Depth in the Pacific Ocean  

Science Journals Connector (OSTI)

Sound speeds calculated from the physical properties of sea water as measured at hydrographic stations were used to construct contour charts of SOFAR?speed and SOFAR?axis depth for the Pacific Ocean. Wilson's formula was used for the calculation of speed. Data were averaged for 1 squares plotted and smooth contours were drawn manually. Speeds averaged along great?circle paths are compared with those measured for explosions. The charts show steep gradients along the Antarctic convergence and at the convergence of the Oyashio and Kuroshio extension. The region of highest speed as well as greatest axis depth was that extending eastward from Australia to about the 150W. The charts are used in a program for calculating source coordinates of earthquakeT phases.

Rockne H. Johnson; Roger A. Norris

1967-01-01T23:59:59.000Z

257

Salinity routing in reservoir system modeling  

E-Print Network (OSTI)

.......................39 Figure 3.6 Sulfate concentration at Seymour gauge observed by USGS..........................39 Figure 3.7 TDS concentration at Richmond gauge observed by USGS............................40 Figure 3.8 Chloride concentration at Richmond... and three major upper reservoirs in the Brazos River Basin.......36 Figure 3.4 TDS concentration at Seymour gauge observed by USGS..............................38 Figure 3.5 Chloride concentration at Seymour gauge observed by USGS...

Ha, Mi Ae

2007-04-25T23:59:59.000Z

258

SEISMIC DETERMINATION OF RESERVOIR HETEROGENEITY: APPLICATION TO THE CHARACTERIZATION OF HEAVY OIL RESERVOIRS  

SciTech Connect

The objective of the project was to examine how seismic and geologic data can be used to improve characterization of small-scale heterogeneity and their parameterization in reservoir models. The study focused on West Coalinga Field in California. The project initially attempted to build reservoir models based on different geologic and geophysical data independently using different tools, then to compare the results, and ultimately to integrate them all. We learned, however, that this strategy was impractical. The different data and tools need to be integrated from the beginning because they are all interrelated. This report describes a new approach to geostatistical modeling and presents an integration of geology and geophysics to explain the formation of the complex Coalinga reservoir.

Matthias G. Imhof; James W. Castle

2005-02-01T23:59:59.000Z

259

Effect of connate water on miscible displacement of reservoir oil by flue gas  

E-Print Network (OSTI)

Average Reservoir Fluid Pro erties Before Break- Through Ultimate Economic Re cover Fraction OIP 1(a) (b) (c) 2(a) (b) (c) 3(a) (b) (c) (b) (c) (d) 5(*) (b) (c} 6(a) (b) (c) 3800 4200 4600 3800 4200 4600 3800 4ZOO 4600 3000...-through recovery of 75 per cent. Nitrogen resulted in an 81 per cent break- through recovery, after reaching miscibility at 4160 psi. Although nitrogen gave a higher break-through recovery than flue gas, flue gas 25 0. 80 4600 psi 4200 psi f4 0 0 0 'g 4...

Maxwell, H. D.

2012-06-07T23:59:59.000Z

260

Cherokee Reservoir: supplement to factors affecting water quality in Cherokee Reservoir  

SciTech Connect

Several rates and/or measurements were assumed in preparation of the Factors Affecting Water Quality in Cherokee Reservoir report prepared by Iwanski, et al. (1980). The following discussions and data were generated to support future modeling efforts of Cherokee Reservoir water quality. These discussions are not wholly intended to define conclusions or new findings, but rather lend support to assumed parameters in the modeling effort. The data include: (1) long-term BOD analyses; (2) limiting nutrient studies algal assays; (3) phytoplankton biomass; (4) primary productivity; and (5) solids transport. 10 references, 3 figures, 5 tables. (ACR)

Poppe, W.L.

1981-09-14T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

FLUID STRATIGRAPHY OF THE COSO GEOTHERMAL RESERVOIR | Open Energy  

Open Energy Info (EERE)

FLUID STRATIGRAPHY OF THE COSO GEOTHERMAL RESERVOIR FLUID STRATIGRAPHY OF THE COSO GEOTHERMAL RESERVOIR Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: FLUID STRATIGRAPHY OF THE COSO GEOTHERMAL RESERVOIR Details Activities (1) Areas (1) Regions (0) Abstract: A fluid model for the Coso geothermal reservoir is developed from Fluid Inclusion Stratigraphy (FIS) analyses. Fluid inclusion gas chemistry in well cuttings collected at 20 ft intervals is analyzed and plotted on well log diagrams. The working hypothesis is that select gaseous species and species ratios indicate areas of groundwater and reservoir fluid flow, fluid processes and reservoir seals. Boiling and condensate zones are distinguished. Models are created using cross-sections and fence diagrams. A thick condensate and boiling zone is indicated across the western portion

262

Fluid Stratigraphy and Permeable Zones of the Coso Geothermal Reservoir |  

Open Energy Info (EERE)

Stratigraphy and Permeable Zones of the Coso Geothermal Reservoir Stratigraphy and Permeable Zones of the Coso Geothermal Reservoir Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: Fluid Stratigraphy and Permeable Zones of the Coso Geothermal Reservoir Details Activities (1) Areas (1) Regions (0) Abstract: A fence-diagram for the Coso geothermal reservoir is developed from Fluid Inclusion Stratigraphy (FIS) analyses. Fluid inclusion gas chemistry in well cuttings collected at 20 ft intervals is analyzed and plotted on well log diagrams. The working hypothesis is that select gaseous species and species ratios indicate areas of groundwater and reservoir fluid flow, fluid processes and reservoir seals. Boiling and condensate zones are distinguished. Permeable zones are indicated by a large change in

263

Borehole geophysics evaluation of the Raft River geothermal reservoir |  

Open Energy Info (EERE)

reservoir reservoir Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Book: Borehole geophysics evaluation of the Raft River geothermal reservoir Details Activities (1) Areas (1) Regions (0) Abstract: Borehole geophysics techniques were used in evaluating the Raft River geothermal reservoir to establish a viable model for the system. The assumed model for the hot water (145/sup 0/C) reservoir was a zone of higher conductivity, increased porosity, decreased density, and lower sonic velocity. It was believed that the long term contact with the hot water would cause alteration producing these effects. With this model in mind, cross-plots of the above parameters were made to attempt to delineate the reservoir. It appears that the most meaningful data include smoothed and

264

Productivity evaluation and influential factor analysis for Sarvak reservoir in South Azadegan oil field, Iran  

Science Journals Connector (OSTI)

Abstract Production pattern of oil wells and influential factors on productivity for the massive carbonate reservoir in the Middle East were researched by productivity evaluation on Sarvak and analysis of properties impact on production. Based on dynamic performance of Sarvak production test, the relationship between daily oil production, tubing pressure, cumulative oil production and choke size was analyzed and reasonable productivity prediction model was established by applying Poettman model, and the effect of physical properties and fluid parameters on productivity were analyzed further by numerical simulation. The study shows that daily oil production is linearly correlated with oil pressure under certain working regime, and daily oil production is power law correlated with choke sizes before and after working regime adjustment. The average designed single well productivity should be about 270 m3/d by depletion to ensure a three-year plateau period. Sarvak is a blocky carbonate reservoir, when developed with horizontal wells, interbeds distributed between layers and permeability property have the strongest impact on production of horizontal wells. So, highly deviated wells should be used to reduce the effect of interbeds and acidizing should be considered to improve the reservoir physical properties.

Hui LIU; Rui GUO; Junchang DONG; Li LIU; Yang LIU; Yingjie YI

2013-01-01T23:59:59.000Z

265

Using precision gravity data in geothermal reservoir engineering modeling studies  

SciTech Connect

Precision gravity measurements taken at various times over a geothermal field can be used to derive information about influx into the reservoir. Output from a reservoir simulation program can be used to compute surface gravity fields and time histories. Comparison of such computer results with field-measured gravity data can add confidence to simulation models, and provide insight into reservoir processes. Such a comparison is made for the Bulalo field in the Philippines.

Atkinson, Paul G.; Pederseen, Jens R.

1988-01-01T23:59:59.000Z

266

Geothermal Reservoir Technology Research Program: Abstracts of selected research projects  

SciTech Connect

Research projects are described in the following areas: geothermal exploration, mapping reservoir properties and reservoir monitoring, and well testing, simulation, and predicting reservoir performance. The objectives, technical approach, and project status of each project are presented. The background, research results, and future plans for each project are discussed. The names, addresses, and telephone and telefax numbers are given for the DOE program manager and the principal investigators. (MHR)

Reed, M.J. (ed.)

1993-03-01T23:59:59.000Z

267

Analysis of a geopressured gas reservoir using solution plot method  

E-Print Network (OSTI)

dependent formation compressibility and water influx require extensive study of the reservoir core samples and aquifer characteristics that are not commonly conducted. Poston and Chen solved this problem by re-arranging the material balance equation... of water compressibility (c~) and formation compressibility (c/ ). Studies of geopressured gas reservoirs have shown such reservoirs to be generally associated with either interbedded shales and or an aquifer. Each of these conditions can provide...

Hussain, Syed Muqeedul

1992-01-01T23:59:59.000Z

268

[open quotes]2-Step[close quotes] log analysis of the Spellacy reservoir in the giant Midway-Sunset Field, Kern County, California  

SciTech Connect

A technique is presented for simple, effective log analysis of (Miocene) [open quotes]Spellacy[close quotes] sands and conglomerates of the Santa Margarita Formation at Midway-Sunset Field in Kern County, California. Results are shown graphically on the log display and are quantified for mapping. Requirements are digital wireline data -- in this simple case, just resistivity and porosities - and flexible log analysis software such as QLA2[trademark]. The first step of this technique discriminates between reservoir-quality and non-reservoir-quality intervals yielding three color-coded categories. A narrow color-filled column is added to the well log display to graphically communicate the vertical distribution of reservoir-quality and barrier intervals. The second step performs a fluid analysis on the reservoir-quality category (intervals) yielding three more color-coded categories. The results of the fluid analysis are graphically displayed in a second narrow color-filled column on the well log. Analysis results are captured from a tabular report for mapping. Quantifiable products include (1) thicknesses: original net pay, current net pay, reservoir quality, total sand, total porosity, phi-H, etc.; (2) averages: original net pay porosity; current net pay porosity, current net pay saturation, current net pay bulk volume oil, etc.; and (3) ratios: thickness of reservoir quality to total sand and thickness of current net pay to total interval.

Sturm, D.H. (Santa Fe Energy Resources, Bakersfield, CA (United States))

1996-01-01T23:59:59.000Z

269

{open_quotes}2-Step{close_quotes} log analysis of the Spellacy reservoir in the giant Midway-Sunset Field, Kern County, California  

SciTech Connect

A technique is presented for simple, effective log analysis of (Miocene) {open_quotes}Spellacy{close_quotes} sands and conglomerates of the Santa Margarita Formation at Midway-Sunset Field in Kern County, California. Results are shown graphically on the log display and are quantified for mapping. Requirements are digital wireline data -- in this simple case, just resistivity and porosities - and flexible log analysis software such as QLA2{trademark}. The first step of this technique discriminates between reservoir-quality and non-reservoir-quality intervals yielding three color-coded categories. A narrow color-filled column is added to the well log display to graphically communicate the vertical distribution of reservoir-quality and barrier intervals. The second step performs a fluid analysis on the reservoir-quality category (intervals) yielding three more color-coded categories. The results of the fluid analysis are graphically displayed in a second narrow color-filled column on the well log. Analysis results are captured from a tabular report for mapping. Quantifiable products include (1) thicknesses: original net pay, current net pay, reservoir quality, total sand, total porosity, phi-H, etc.; (2) averages: original net pay porosity; current net pay porosity, current net pay saturation, current net pay bulk volume oil, etc.; and (3) ratios: thickness of reservoir quality to total sand and thickness of current net pay to total interval.

Sturm, D.H. [Santa Fe Energy Resources, Bakersfield, CA (United States)

1996-12-31T23:59:59.000Z

270

OUTDOOR RECREATION DEMAND AND EXPENDITURES: LOWER SNAKE RIVER RESERVOIRS  

E-Print Network (OSTI)

i OUTDOOR RECREATION DEMAND AND EXPENDITURES: LOWER SNAKE RIVER RESERVOIRS John R. Mc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v SECTION ONE - OUTDOOR RECREATION DEMAND . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Recreation Demand Methods

O'Laughlin, Jay

271

5641_FrozenReservoirs | netl.doe.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

parallel to the structure. These fractures could play a major role in enhancing vertical permeability and vertical connectivity in a reservoir that is otherwise highly...

272

Field Algae Measurements Using Empirical Correlations at Deer Creek Reservoir.  

E-Print Network (OSTI)

??Deer Creek Reservoir in Utah has a history of high algae concentrations. Despite recent nutrient reduction efforts, seasonal algae continue to present problems. Cost effective, (more)

Stephens, Ryan A.

2011-01-01T23:59:59.000Z

273

Carbonation Mechanism of Reservoir Rock by Supercritical Carbon...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

the carbonation reaction mechanisms between supercritical carbon dioxide (scCO2) and reservoir rocks consisting of different mineralogical compositions in aqueous and...

274

Texas State Offshore Crude Oil + Lease Condensate New Reservoir...  

U.S. Energy Information Administration (EIA) Indexed Site

disclosure of individual company data. Release Date: 4102014 Next Release Date: 4302015 Referring Pages: Crude Oil plus Lease Condensate New Reservoir Discoveries in Old Fields...

275

California State Offshore Crude Oil + Lease Condensate New Reservoir...  

U.S. Energy Information Administration (EIA) Indexed Site

disclosure of individual company data. Release Date: 4102014 Next Release Date: 4302015 Referring Pages: Crude Oil plus Lease Condensate New Reservoir Discoveries in Old Fields...

276

,"New York Crude Oil Reserves in Nonproducing Reservoirs (Million...  

U.S. Energy Information Administration (EIA) Indexed Site

Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","New York Crude Oil Reserves in Nonproducing Reservoirs (Million Barrels)",1,"Annual",2013...

277

,"Texas--State Offshore Crude Oil Reserves in Nonproducing Reservoirs...  

U.S. Energy Information Administration (EIA) Indexed Site

Of Series","Frequency","Latest Data for" ,"Data 1","Texas--State Offshore Crude Oil Reserves in Nonproducing Reservoirs (Million Barrels)",1,"Annual",2013...

278

Evaluation of testing and reservoir parameters in geothermal...  

Open Energy Info (EERE)

testing and reservoir parameters in geothermal wells at Raft River and Boise, Idaho Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Proceedings:...

279

Hydraulics and Well Testing of Engineered Geothermal Reservoirs...  

Open Energy Info (EERE)

Hydraulics and Well Testing of Engineered Geothermal Reservoirs Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Hydraulics and Well Testing of...

280

Lower Watts Bar Reservoir Clinch River/Poplar Creek  

Energy.gov (U.S. Department of Energy (DOE))

This document explains the cleanup activities and any use limitations for the land surrounding the Lower Watts Bar Reservoir Clinch River/Poplar Creek.

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Three-dimensional Modeling of Fracture Clusters in Geeothermal Reservoirs  

Energy.gov (U.S. Department of Energy (DOE))

Three-dimensional Modeling of Fracture Clusters in Geeothermal Reservoirs presentation at the April 2013 peer review meeting held in Denver, Colorado.

282

Reservoir-Scale Fracture Permeability in the Dixie Valley, Nevada...  

Open Energy Info (EERE)

Reservoir-Scale Fracture Permeability in the Dixie Valley, Nevada, Geothermal Field Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper:...

283

Monitoring and Modeling Fluid Flow in a Developing EGS Reservoir...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

More Documents & Publications Imaging, Characterizing, and Modeling of Fracture Networks and Fluid Flow in EGS Reservoirs Detection and Characterization of Natural...

284

Application of thermal depletion model to geothermal reservoirs...  

Open Energy Info (EERE)

of thermal depletion model to geothermal reservoirs with fracture and pore permeability Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Proceedings:...

285

Fracture Evolution Following a Hydraulic Stimulation within an EGS Reservoir  

Energy.gov (U.S. Department of Energy (DOE))

Fracture Evolution Following a Hydraulic Stimulation within an EGS Reservoir presentation at the April 2013 peer review meeting held in Denver, Colorado.

286

Dispersed Fluid Flow in Fractured Reservoirs- an Analysis of...  

Open Energy Info (EERE)

correlations. Downhole measurements of the tracer response exiting from discrete fracture zones permit further characterization of reservoir fluid flow behavior. Tracer...

287

FLUID INCLUSION STRATIGRAPHY: NEW METHOD FOR GEOTHERMAL RESERVOIR...  

Open Energy Info (EERE)

RESERVOIR ASSESSMENT PRELIMINARY RESULTS Abstract Fluid Inclusion Stratigraphy (FIS) is a new technique developed for the oil industry in order to map borehole fluids....

288

Methodologies for Reservoir Characterization Using Fluid Inclusion Gas Chemistry  

Energy.gov (U.S. Department of Energy (DOE))

Methodologies for Reservoir Characterization Using Fluid Inclusion Gas Chemistry presentation at the April 2013 peer review meeting held in Denver, Colorado.

289

Prediction of coalbed methane reservoir performance with type curves.  

E-Print Network (OSTI)

??Coalbed methane is an unconventional gas resource that consists of methane production from the coal seams. CBM reservoirs are dual-porosity systems that are characterized by (more)

Bhavsar, Amol Bhaskar.

2005-01-01T23:59:59.000Z

290

WATERJETTING: A NEW DRILLING TECHNIQUE IN COALBED METHANE RESERVOIRS.  

E-Print Network (OSTI)

??WATERJETTING: A NEW DRILLING TECHNIQUE IN COALBED METHANE RESERVOIRS Applications of waterjeting to drill horizontal wells for the purpose of degassing coalbeds prior to mining (more)

Funmilayo, Gbenga M.

2010-01-01T23:59:59.000Z

291

,"U.S. Coalbed Methane Proved Reserves New Reservoir Discoveries...  

U.S. Energy Information Administration (EIA) Indexed Site

Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","U.S. Coalbed Methane Proved Reserves New Reservoir Discoveries in Old Fields (Billion Cubic...

292

Impact of Langmuir isotherm on production behavior of CBM reservoirs.  

E-Print Network (OSTI)

??Coalbed Methane is an unconventional gas resource that consists of methane production from the coal seams. CBM reservoir performance is also influenced by the interrelationship (more)

Arrey, Efundem Ndipanquang.

2004-01-01T23:59:59.000Z

293

THMC Modeling of EGS Reservoirs ?Continuum through Discontinuum...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Evolution and Induced Seismicity Derek Elsworth Pennsylvania State University Chemistry, Reservoir and Integrated Models May 19, 2010 This presentation does not contain any...

294

Variations in dissolved gas compositions of reservoir fluids...  

Open Energy Info (EERE)

A. E.; Copp, J. F. . 111991. Variations in dissolved gas compositions of reservoir fluids from the Coso geothermal field. Proceedings of () ; () : Sixteenth workshop on...

295

APPLICATION OF RESERVOIR CHARACTERIZATION AND ADVANCED TECHNOLOGY TO IMPROVE RECOVERY AND ECONOMICS IN A LOWER QUALITY SHALLOW SHELF SANANDRES RESERVOIR  

SciTech Connect

The Class 2 Project at West Welch was designed to demonstrate the use of advanced technologies to enhance the economics of improved oil recovery (IOR) projects in lower quality Shallow Shelf Carbonate (SSC) reservoirs, resulting in recovery of additional oil that would otherwise be left in the reservoir at project abandonment. Accurate reservoir description is critical to the effective evaluation and efficient design of IOR projects in the heterogeneous SSC reservoirs. Therefore, the majority of Budget Period 1 was devoted to reservoir characterization. Technologies being demonstrated include: (1) Advanced petrophysics; (2) Three-dimensional (3-D) seismic; (3) Crosswell bore tomography; (4) Advanced reservoir simulation; (5) Carbon dioxide (CO{sub 2}) stimulation treatments; (6) Hydraulic fracturing design and monitoring; (7) Mobility control agents.

Unknown

2003-01-15T23:59:59.000Z

296

Shear-slip analysis in multiphase fluid-flow reservoir engineering ap plications using TOUGH-FLAC  

E-Print Network (OSTI)

IN MULTIPHASE FLUID-FLOW RESERVOIR ENGINEERING APPLICATIONSin multiphase fluid-flow reservoir-engineering applications.in multiphase fluid-flow reservoir engineering applications.

Rutqvist, Jonny; Birkholzer, Jens; Cappa, Frederic; Oldenburg, Curt; Tsang, Chin-Fu

2008-01-01T23:59:59.000Z

297

CO2 gas/oil ratio prediction in a multi-component reservoir by combined seismic and electromagnetic imaging  

E-Print Network (OSTI)

CO 2 flooding of an oil reservoir are inverted to producein a complex reservoir containing oil, water, hydrocarbonincluding oil, water and gas) and reservoir pressure. The

Hoversten, G.M.; Gritto, Roland; Washbourne, John; Daley, Tom

2002-01-01T23:59:59.000Z

298

Assessment of halite-cemented reservoir zones  

SciTech Connect

This paper describes the techniques used to identify the presence and distribution of halite-cemented layers in a sandstone oil reservoir. The distribution of these layers in the wells was found by matching the core data with two independent halite identifiers from the well logs. Numerical well models were used to assess the dimensions and spatial distribution of the halite-cemented layers. Multiple simulation runs in which the spatial distribution, the dimensions, and the vertical permeability were varied resulted in a stochastic model that best matched the production history. Gas and water coning are retarded by the halite-cemented layers if the perforations are properly located.

Huurdeman, A.J.M.; Floris, F.J.T.; Lutgert, J.E. (TNO Inst. of Applied Geoscience (NL)); Breunese, J.N. (Geological Survey of the Netherlands (NL)); Al-Asbahl, A.M.S. (Ministry of Oil and Mineral Resources (YE))

1991-05-01T23:59:59.000Z

299

A better understanding of a Uinta Basin channelized analog reservoir through geostatistics and reservoir simulation  

E-Print Network (OSTI)

the behavior of channelized oil and gas reservoirs. Results show that the number of channels in the model can have a significant effect on performance. The rock properties in these channels and the channel paths are also important factors that determine...

Robbana, Enis

2012-06-07T23:59:59.000Z

300

A petrophysics and reservoir performance-based reservoir characterization of Womack Hill (Upper Smackover) Field (Alabama)  

E-Print Network (OSTI)

as well as to optimize the operating practices in the field. We used a non-parametric regression algorithm (ACE) to develop correlations between the core and well log data. These correlations allow us to estimate reservoir permeability at the "flow unit...

Avila Urbaneja, Juan Carlos

2012-06-07T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average  

NLE Websites -- All DOE Office Websites (Extended Search)

8: July 12, 2004 8: July 12, 2004 Expected Average Annual Miles to someone by E-mail Share Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Facebook Tweet about Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Twitter Bookmark Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Google Bookmark Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Delicious Rank Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Digg Find More places to share Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on AddThis.com... Fact #328: July 12, 2004 Expected Average Annual Miles Twenty-five percent of the respondents to a nationwide survey said that

302

Fact #614: March 15, 2010 Average Age of Household Vehicles  

Energy.gov (U.S. Department of Energy (DOE))

The average age of household vehicles has increased from 6.6 years in 1977 to 9.2 years in 2009. Pickup trucks have the oldest average age in every year listed. Sport utility vehicles (SUVs), first...

303

Fact #615: March 22, 2010 Average Vehicle Trip Length  

Energy.gov (U.S. Department of Energy (DOE))

According to the latest National Household Travel Survey, the average trip length grew to over 10 miles in 2009, just slightly over the 9.9 mile average in 2001. Trips to work in 2009 increased to...

304

Fact #835: August 25, Average Historical Annual Gasoline Pump...  

Energy Savers (EERE)

5: August 25, Average Historical Annual Gasoline Pump Price, 1929-2013 Fact 835: August 25, Average Historical Annual Gasoline Pump Price, 1929-2013 When adjusted for inflation,...

305

Depth profiling ambient noise in the deep ocean  

E-Print Network (OSTI)

al. , 2005). The vertical profile of wind speed over the seavertical directionality Depth-dependence of wind speedVertical noise directional density function versus depth. 93 Measured and acoustically estimated wind speeds.

Barclay, David Readshaw

2011-01-01T23:59:59.000Z

306

Application of integrated reservoir management and reservoir characterization to optimize infill drilling. Annual report, June 13, 1994--June 12, 1995  

SciTech Connect

This project has used a multi-disciplinary approach employing geology, geophysics, and engineering to conduct advanced reservoir characterization and management activities to design and implement an optimized infill drilling program at the North Robertson (Clearfork) Unit in Gaines County, Texas. The activities during the first Budget Period have consisted of developing an integrated reservoir description from geological, engineering, and geostatistical studies, and using this description for reservoir flow simulation. Specific reservoir management activities are being identified and tested. The geologically targeted infill drilling program will be implemented using the results of this work. A significant contribution of this project is to demonstrate the use of cost-effective reservoir characterization and management tools that will be helpful to both independent and major operators for the optimal development of heterogeneous, low permeability shallow-shelf carbonate (SSC) reservoirs. The techniques that are outlined for the formulation of an integrated reservoir description apply to all oil and gas reservoirs, but are specifically tailored for use in the heterogeneous, low permeability carbonate reservoirs of West Texas.

Pande, P.K.

1996-11-01T23:59:59.000Z

307

Spherical averages and applications to spherical splines and interpolation  

Science Journals Connector (OSTI)

This article introduces a method for computing weighted averages on spheres based on least squares minimization that respects spherical distance. We prove existence and uniqueness properties of the weighted averages, and give fast iterative algorithms ... Keywords: Bzier curve, B-spline, barycentric coordinates, least squares minimization, quaternion interpolation, quaternions, spherical average, spherical interpolation, spherical mean, spline curve, spline interpolation

Samuel R. Buss; Jay P. Fillmore

2001-04-01T23:59:59.000Z

308

Twentieth workshop on geothermal reservoir engineering: Proceedings  

SciTech Connect

PREFACE The Twentieth Workshop on Geothermal Reservoir Engineering, dedicated to the memory of Professor Hank Ramey, was held at Stanford University on January 24-26, 1995. There were ninety-five registered participants. Participants came from six foreign countries: Japan, Mexico, England, Italy, New Zealand and Iceland. The performance of many geothermal reservoirs outside the United States was described in several of the papers. Professor Roland N. Horne opened the meeting and welcomed visitors to the campus. The key note speaker was Marshall Reed, who gave a brief overview of the Department of Energy's current plan. Thirty-two papers were presented in the technical sessions of the workshop. Technical papers were organized into eleven sessions concerning: field development, modeling, well tesubore, injection, geoscience, geochemistry and field operations. Session chairmen were major contributors to the workshop, and we thank: Ben Barker, Bob Fournier, Mark Walters, John Counsil, Marcelo Lippmann, Keshav Goyal, Joel Renner and Mike Shook. In addition to the technical sessions, a panel discussion was held on ''What have we learned in 20 years?'' Panel speakers included Patrick Muffler, George Frye, Alfred Truesdell and John Pritchett. The subject was further discussed by Subir Sanyal, who gave the post-dinner speech at the banquet. The Workshop was organized by the Stanford Geothermal Program faculty, staff, and graduate students. We wish to thank our students who operated the audiovisual equipment. Shaun D. Fitzgerald Program Manager

None

1995-01-26T23:59:59.000Z

309

Rabi multi-sector reservoir simulation model  

SciTech Connect

To ensure optimum ultimate recovery of the 46 meter thick oil rim of the Rabi Field in Gabon, a full field simulation model was required. Due to it`s size and complexity, with local cusping, coning and geological circumstances dominating individual well behavior, a single full field model would be too large for existing hardware. A method was developed to simulate the full field with 5 separate sector models, whilst allowing the development in one sector model to have an effect on the boundary conditions of another sector. In this manner, the 13 x 4.5 km field could be simulated with a horizontal well spacing down to 175 meter. This paper focuses on the method used to attach single 3-phase tank cells to a sector simulation grid in order to represent non-simulated parts of the field. It also describes the history matching methodology and how to run a multisector model in forecasting mode. This method can be used for any reservoir, where size and complexity require large reservoir simulation models that normally could not be modeled within the constraints of available computer facilities. Detailed studies can be conducted on specific parts of a field, whilst allowing for dynamic flow and pressure effects caused by the rest of the field.

Bruijnzeels, C.; O`Halloran, C.

1995-12-31T23:59:59.000Z

310

Reservoir permeability from seismic attribute analysis  

SciTech Connect

In case of porous fluid-saturated medium the Biot's poroelasticity theory predicts a movement of the pore fluid relative to the skeleton on seismic wave propagation through the medium. This phenomenon opens an opportunity for investigation of the flow properties of the hydrocarbon-saturated reservoirs. It is well known that relative fluid movement becomes negligible at seismic frequencies if porous material is homogeneous and well cemented. In this case the theory predicts an underestimated seismic wave velocity dispersion and attenuation. Based on Biot's theory, Helle et al. (2003) have numerically demonstrated the substantial effects on both velocity and attenuation by heterogeneous permeability and saturation in the rocks. Besides fluid flow effect, the effects of scattering (Gurevich, et al., 1997) play very important role in case of finely layered porous rocks and heterogeneous fluid saturation. We have used both fluid flow and scattering effects to derive a frequency-dependent seismic attribute which is proportional to fluid mobility and applied it for analysis of reservoir permeability.

Silin, Dmitriy; Goloshubin, G.; Silin, D.; Vingalov, V.; Takkand, G.; Latfullin, M.

2008-02-15T23:59:59.000Z

311

Output-Sensitive Algorithms for Tukey Depth and Related Problems  

E-Print Network (OSTI)

Output-Sensitive Algorithms for Tukey Depth and Related Problems David Bremner University of New de Bruxelles Pat Morin Carleton University Abstract The Tukey depth (Tukey 1975) of a point p halfspace that contains p. Algorithms for computing the Tukey depth of a point in various dimensions

Morin, Pat

312

Sixth workshop on geothermal reservoir engineering: Proceedings  

SciTech Connect

INTRODUCTION TO THE PROCEEDINGS OF THE SIXTH GEOTHERMAL RESERVOIR ENGINEERING WORKSHOP, STANFORD GEOTHERMAL PROGRAM Henry J. Ramey, Jr., and Paul Kruger Co-Principal Investigators Ian G. Donaldson Program Manager Stanford Geothermal Program The Sixth Workshop on Geothermal Reservoir Engineering convened at Stanford University on December 16, 1980. As with previous Workshops the attendance was around 100 with a significant participation from countries other than the United States (18 attendees from 6 countries). In addition, there were a number of papers from foreign contributors not able to attend. Because of the success of all the earlier workshops there was only one format change, a new scheduling of Tuesday to Thursday rather than the earlier Wednesday through Friday. This change was in general considered for the better and will be retained for the Seventh Workshop. Papers were presented on two and a half of the three days, the panel session, this year on the numerical modeling intercomparison study sponsored by the Department of Energy, being held on the second afternoon. This panel discussion is described in a separate Stanford Geothermal Program Report (SGP-TR42). This year there was a shift in subject of the papers. There was a reduction in the number of papers offered on pressure transients and well testing and an introduction of several new subjects. After overviews by Bob Gray of the Department of Energy and Jack Howard of Lawrence Berkeley Laboratory, we had papers on field development, geopressured systems, production engineering, well testing, modeling, reservoir physics, reservoir chemistry, and risk analysis. A total of 51 papers were contributed and are printed in these Proceedings. It was, however, necessary to restrict the presentations and not all papers printed were presented. Although the content of the Workshop has changed over the years, the format to date has proved to be satisfactory. The objectives of the Workshop, the bringing together of researchers, engineers and managers involved in geothermal reservoir study and development and the provision of a forum for the prompt and open reporting of progress and for the exchange of ideas, continue to be met . Active discussion by the majority of the participants is apparent both in and outside the workshop arena. The Workshop Proceedings now contain some of the most highly cited geothermal literature. Unfortunately, the popularity of the Workshop for the presentation and exchange of ideas does have some less welcome side effects. The major one is the developing necessity for a limitation of the number of papers that are actually presented. We will continue to include all offered papers in the Summaries and Proceedings. As in the recent past, this sixth Workshop was supported by a grant from the Department of Energy. This grant is now made directly to Stanford as part of the support for the Stanford Geothermal Program (Contract No. DE-AT03-80SF11459). We are certain that all participants join us in our appreciation of this continuing support. Thanks are also due to all those individuals who helped in so many ways: The members of the program committee who had to work so hard to keep the program to a manageable size - George Frye (Aminoil USA), Paul G. Atkinson (Union Oil Company). Michael L. Sorey (U.S.G.S.), Frank G. Miller (Stanford Geothermal Program), and Roland N. Horne (Stanford Geothermal Program). The session chairmen who contributed so much to the organization and operation of the technical sessions - George Frye (Aminoil USA), Phillip H. Messer (Union Oil Company), Leland L. Mink (Department of Energy), Manuel Nathenson (U.S.G.S.), Gunnar Bodvarsson (Oregon State University), Mohindar S. Gulati (Union Oil Company), George F. Pinder (Princeton University), Paul A. Witherspoon (Lawrence Berkeley Laboratory), Frank G. Miller (Stanford Geothermal Program) and Michael J. O'Sullivan (Lawrence Berkeley Laboratory). The many people who assisted behind the scenes, making sure that everything was prepared and organized - in particular we would like to t

Ramey, H.J. Jr.; Kruger, P. (eds.)

1980-12-18T23:59:59.000Z

313

Methods and systems using encapsulated tracers and chemicals for reservoir interrogation and manipulation  

DOE Patents (OSTI)

An apparatus, method, and system of reservoir interrogation. A tracer is encapsulating in a receptacle. The receptacle containing the tracer is injected into the reservoir. The tracer is analyzed for reservoir interrogation.

Roberts, Jeffery; Aines, Roger D; Duoss, Eric B; Spadaccini, Christopher M

2014-11-04T23:59:59.000Z

314

Integrated Hydraulic Fracture Placement and Design Optimization in Unconventional Gas Reservoirs  

E-Print Network (OSTI)

Unconventional reservoir such as tight and shale gas reservoirs has the potential of becoming the main source of cleaner energy in the 21th century. Production from these reservoirs is mainly accomplished through engineered hydraulic fracturing...

Ma, Xiaodan

2013-12-10T23:59:59.000Z

315

A Hierarchical Multiscale Approach to History Matching and Optimization for Reservoir Management in Mature Fields  

E-Print Network (OSTI)

Reservoir management typically focuses on maximizing oil and gas recovery from a reservoir based on facts and information while minimizing capital and operating investments. Modern reservoir management uses history-matched simulation model...

Park, Han-Young

2012-10-19T23:59:59.000Z

316

Fracture Modeling and Flow Behavior in Shale Gas Reservoirs Using Discrete Fracture Networks  

E-Print Network (OSTI)

Fluid flow process in fractured reservoirs is controlled primarily by the connectivity of fractures. The presence of fractures in these reservoirs significantly affects the mechanism of fluid flow. They have led to problems in the reservoir which...

Ogbechie, Joachim Nwabunwanne

2012-02-14T23:59:59.000Z

317

Thermo-Poroelastic Modeling of Reservoir Stimulation and Microseismicity Using Finite Element Method with Damage Mechanics  

E-Print Network (OSTI)

Stress and permeability variations around a wellbore and in the reservoir are of much interest in petroleum and geothermal reservoir development. Water injection causes significant changes in pore pressure, temperature, and stress in hot reservoirs...

Lee, Sang Hoon

2012-02-14T23:59:59.000Z

318

Flood Operation Rules for a Single Reservoir Licheng Dong  

E-Print Network (OSTI)

, University of California - Davis 2012-12-12 Abstract This paper examines the theoretical behavior ecosystems. 2. Simple Inflow Hydrographs Three main factors affect the reservoir's inflow flood volume and peak outflow (Ergish, 2010): 1) inflow hydrograph volume and shape; 2) controllable reservoir storage

Lund, Jay R.

319

General inflow performance relationship for solution-gas reservoir wells  

SciTech Connect

Two equations are developed to describe the inflow performance relationship (IPR) of wells producing from solution-gas drive reservoirs. These are general equations (extensions of the currently available IPR's) that apply to wells with any drainage-area shape at any state of completion flow efficiency and any stage of reservoir depletion. 7 refs.

Dias-Couto, L.E.; Golan, M.

1982-02-01T23:59:59.000Z

320

WestVirginiaUniversity SPE 65675 Reservoir Characterization  

E-Print Network (OSTI)

to measure effective porosity (MPHI) and irreducible water saturation (MBVI) in the reservoir rock to accurately characterize effective porosity, fluid saturation and permeability. WestVirginiaUniversity #12WestVirginiaUniversity SPE 65675 SPE 65675 Reservoir Characterization Through Synthetic Logs Shahab

Mohaghegh, Shahab

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Resolution of reservoir scale electrical anisotropy from marine CSEM data  

SciTech Connect

A combination of 1D and 3D forward and inverse solutions is used to quantify the sensitivity and resolution of conventional controlled source electromagnetic (CSEM) data collected using a horizontal electric dipole source to transverse electrical anisotropy located in a deep-water exploration reservoir target. Since strongly anisotropic shale layers have a vertical resistivity that can be comparable to many reservoirs, we examine how CSEM can discriminate confounding shale layers through their characteristically lower horizontal resistivity. Forward modeling demonstrates that the sensitivity to reservoir level anisotropy is very low compared to the sensitivity to isotropic reservoirs, especially when the reservoir is deeper than about 2 km below the seabed. However, for 1D models where the number of inversion parameters can be fixed to be only a few layers, both vertical and horizontal resistivity of the reservoir can be well resolved using a stochastic inversion. We find that the resolution of horizontal resistivity increases as the horizontal resistivity decreases. We show that this effect is explained by the presence of strong horizontal current density in anisotropic layers with low horizontal resistivity. Conversely, when the reservoir has a vertical to horizontal resistivity ratio of about 10 or less, the current density is vertically polarized and hence has little sensitivity to the horizontal resistivity. Resistivity anisotropy estimates from 3D inversion for 3D targets suggest that resolution of reservoir level anisotropy for 3D targets will require good a priori knowledge of the background sediment conductivity and structural boundaries.

Brown, V.; Hoversten, G.M.; Key, K.; Chen, J.

2011-10-01T23:59:59.000Z

322

Evidence for an Ancient Osmium Isotopic Reservoir in Earth  

Science Journals Connector (OSTI)

...ophiolites in the Klamath mountains have extremely...ancient platinum group element reservoir...Oregon Josephine Creek Klamath Mountains mass spectra...platinum platinum group plutonic rocks...ophiolites in the Klamath mountains have extremely...ancient platinum group element reservoir...

Anders Meibom; Robert Frei

2002-04-19T23:59:59.000Z

323

SEDIMENTATION OF THE PANAMA CANAL RESERVOIR: COSMOGENIC NUCLIDE  

E-Print Network (OSTI)

SEDIMENTATION OF THE PANAMA CANAL RESERVOIR: COSMOGENIC NUCLIDE ESTIMATES OF BACKGROUND SEDIMENT, Livermore, CA 94550 The Panama Canal is an engineering marvel. Vital to the operation of the canal, the reservoir to the Panama Canal. In addition to water, the headwater basins supply sediment that reduces

Nichols, Kyle K.

324

Gradient-based Methods for Production Optimization of Oil Reservoirs  

E-Print Network (OSTI)

Gradient-based Methods for Production Optimization of Oil Reservoirs Eka Suwartadi Doctoral Thesis oil reservoirs. Gradient- based optimization, which utilizes adjoint-based gradient computation optimization for water flooding in the secondary phase of oil recovery is the main topic in this thesis

Foss, Bjarne A.

325

Physical model of a fractured reservoir | Open Energy Information  

Open Energy Info (EERE)

model of a fractured reservoir model of a fractured reservoir Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: Physical model of a fractured reservoir Details Activities (1) Areas (1) Regions (0) Abstract: The objectives of the physical modeling effort are to: (1) evaluate injection-backflow testing for fractured reservoirs under conditions of known reservoir parameters (porosity, fracture width, etc.); (2) study the mechanisms controlling solute transport in fracture systems; and (3) provide data for validation of numerical models that explicitly simulate solute migration in fracture systems. The fracture network is 0.57-m wide, 1.7-m long, and consists of two sets of fractures at right angles to one another with a fracture spacing of 10.2 cm. A series of

326

Characterization of geothermal reservoir crack patterns using shear-wave  

Open Energy Info (EERE)

geothermal reservoir crack patterns using shear-wave geothermal reservoir crack patterns using shear-wave splitting Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Characterization of geothermal reservoir crack patterns using shear-wave splitting Details Activities (1) Areas (1) Regions (0) Abstract: Microearthquakes recorded by a downhole, three-component seismic network deployed around the Coso, California, geothermal reservoir since 1992 display distinctive shear-wave splitting and clear polarization directions. From the polarizations the authors estimated three predominant subsurface fracture directions, and from the time delays of the split waves they determined tomographically the 3-D fracture density distribution in the reservoir. Author(s): Lou, M.; Rial, J.A. Published: Geophysics, 3/1/1997

327

Tectonic setting of the Coso geothermal reservoir | Open Energy Information  

Open Energy Info (EERE)

Tectonic setting of the Coso geothermal reservoir Tectonic setting of the Coso geothermal reservoir Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Tectonic setting of the Coso geothermal reservoir Details Activities (1) Areas (1) Regions (0) Abstract: The Coso geothermal reservoir is being developed in Sierran-type crystalline bedrock of the Coso Mountains, a small desert mountain range just to the east of the Sierra Nevada and Rose Valley, which is the southern extension of the Owens Valley of eastern California Optimum development of this reservoir requires an understanding of the fracture hydrology of the Coso Mountains crystalline terrain and its hydrologic connection to regional groundwater and thermal sources. An interpreted, conceptually balanced regional cross section that extends from the Sierra

328

Dams and Reservoirs Safety Act (South Carolina) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Dams and Reservoirs Safety Act (South Carolina) Dams and Reservoirs Safety Act (South Carolina) Dams and Reservoirs Safety Act (South Carolina) < Back Eligibility Utility Commercial Agricultural Investor-Owned Utility Industrial Construction Municipal/Public Utility Local Government Installer/Contractor Rural Electric Cooperative Tribal Government Institutional Savings Category Water Buying & Making Electricity Program Info State South Carolina Program Type Siting and Permitting Provider South Carolina Department of Health and Environmental Control The Dams and Reservoirs Safety Act provides for the certification and inspection of dams in South Carolina and confers regulatory authority on the Department of Health and Environmental Control. Owners of dams and reservoirs are responsible for maintaining the safety of the structures,

329

Geothermal Reservoir Assessment Case Study, Northern Basin and Range  

Open Energy Info (EERE)

Reservoir Assessment Case Study, Northern Basin and Range Reservoir Assessment Case Study, Northern Basin and Range Province, Northern Dixie Valley, Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Geothermal Reservoir Assessment Case Study, Northern Basin and Range Province, Northern Dixie Valley, Nevada Abstract N/A Authors Elaine J. Bell, Lawrence T. Larson and Russell W. Juncal Published U.S. Department of Energy, 1980 Report Number GLO2386 DOI Not Provided Check for DOI availability: http://crossref.org Online Internet link for Geothermal Reservoir Assessment Case Study, Northern Basin and Range Province, Northern Dixie Valley, Nevada Citation Elaine J. Bell,Lawrence T. Larson,Russell W. Juncal. 1980. Geothermal Reservoir Assessment Case Study, Northern Basin and Range Province,

330

Opportunities to improve oil productivity in unstructured deltaic reservoirs  

SciTech Connect

This report contains presentations presented at a technical symposium on oil production. Chapter 1 contains summaries of the presentations given at the Department of Energy (DOE)-sponsored symposium and key points of the discussions that followed. Chapter 2 characterizes the light oil resource from fluvial-dominated deltaic reservoirs in the Tertiary Oil Recovery Information System (TORIS). An analysis of enhanced oil recovery (EOR) and advanced secondary recovery (ASR) potential for fluvial-dominated deltaic reservoirs based on recovery performance and economic modeling as well as the potential resource loss due to well abandonments is presented. Chapter 3 provides a summary of the general reservoir characteristics and properties within deltaic deposits. It is not exhaustive treatise, rather it is intended to provide some basic information about geologic, reservoir, and production characteristics of deltaic reservoirs, and the resulting recovery problems.

Not Available

1991-01-01T23:59:59.000Z

331

High resolution reservoir geological modelling using outcrop information  

SciTech Connect

This is China`s first case study of high resolution reservoir geological modelling using outcrop information. The key of the modelling process is to build a prototype model and using the model as a geological knowledge bank. Outcrop information used in geological modelling including seven aspects: (1) Determining the reservoir framework pattern by sedimentary depositional system and facies analysis; (2) Horizontal correlation based on the lower and higher stand duration of the paleo-lake level; (3) Determining the model`s direction based on the paleocurrent statistics; (4) Estimating the sandbody communication by photomosaic and profiles; (6) Estimating reservoir properties distribution within sandbody by lithofacies analysis; and (7) Building the reservoir model in sandbody scale by architectural element analysis and 3-D sampling. A high resolution reservoir geological model of Youshashan oil field has been built by using this method.

Zhang Changmin; Lin Kexiang; Liu Huaibo [Jianghan Petroleum Institute, Hubei (China)] [and others

1997-08-01T23:59:59.000Z

332

Energy transport between two pure-dephasing reservoirs  

E-Print Network (OSTI)

A pure-dephasing reservoir acting on an individual quantum system induces loss of coherence without energy exchange. When acting on composite quantum systems, dephasing reservoirs can lead to a radically different behavior. Transport of energy between two pure-dephasing markovian reservoirs is predicted in this work. They are connected through a chain of coupled sites. The baths are kept in thermal equilibrium at distinct temperatures. Quantum coherence between sites is generated in the steady-state regime and results in the underlying mechanism sustaining the effect. A quantum model for the reservoirs is a necessary condition for the existence of stationary energy transport. A microscopic derivation of the non-unitary system-bath interaction is employed, valid in the ultrastrong inter-site coupling regime. The model assumes that each site-reservoir coupling is local.

T. Werlang; D. Valente

2014-08-21T23:59:59.000Z

333

Lithology and alteration mineralogy of reservoir rocks at Coso Geothermal  

Open Energy Info (EERE)

Lithology and alteration mineralogy of reservoir rocks at Coso Geothermal Lithology and alteration mineralogy of reservoir rocks at Coso Geothermal Area, California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Lithology and alteration mineralogy of reservoir rocks at Coso Geothermal Area, California Details Activities (1) Areas (1) Regions (0) Abstract: Coso is one of several high-temperature geothermal systems associated with recent volcanic activity in the Basin and Range province. Chemical and fluid inclusion data demonstrate that production is from a narrow, asymmetric plume of thermal water that originates from a deep reservoir to the south and then flows laterally to the north. Geologic controls on the geometry of the upwelling plume were investigated using petrographic and analytical analyses of reservoir rock and vein material.

334

Depth dependence of ambient noise in the northeastern Pacific Ocean  

Science Journals Connector (OSTI)

Omnidirectional ambient noise levels were measured at two deep?water locations in the northeastern Pacific Ocean.Hydrophones were positioned throughout the water column at depths ranging from about 200 m below the surface to about 150 m above the sea bottom. Analyses of the data over the frequencies from 15 to 800 Hz show that at low frequencies the noise levels decrease with increasing depth. The decrease with depth is greater below the critical depth than it is in the sound channel. These low?frequency noise levels and their depth dependence are independent of the wind speed. At higher frequencies the noise levels and the depth dependence are controlled by the wind?generated noise. At low wind speeds there is a decrease in levels below the critical depth but above this depth both increases and decreases in levels with depth were noted. At these high frequencies during high wind speeds the noise levels not only rise but also fill the water column to the extent that there is little decrease in level with increasing depth even for the region below the critical depth.

Gerald B. Morris

1978-01-01T23:59:59.000Z

335

Simulation study to investigate development options for a super-heavy oil reservoir.  

E-Print Network (OSTI)

??A reservoir simulation study was performed on a heavy oil reservoir with the main objective of evaluating possible development options beyond the existing cold production (more)

Diaz Franco, Jose Manuel

2012-01-01T23:59:59.000Z

336

Sizing of a hot dry rock reservoir from a hydraulic fracturing experiment  

SciTech Connect

Hot dry rock (HDR) reservoirs do not lend themselves to the standard methods of reservoir sizing developed in the petroleum industry such as the buildup/drawdown test. In a HDR reservoir the reservoir is created by the injection of fluid. This process of hydraulic fracturing of the reservoir rock usually involves injection of a large volume (5 million gallons) at high rates (40BPM). A methodology is presented for sizing the HDR reservoir created during the hydraulic fracturing process. The reservoir created during a recent fracturing experiment is sized using the techniques presented. This reservoir is then investigated for commercial potential by simulation of long term power production. 5 refs., 7 figs.

Zyvoloski, G.

1985-01-01T23:59:59.000Z

337

U.S. Federal Offshore Crude Oil + Lease Condensate New Reservoir...  

U.S. Energy Information Administration (EIA) Indexed Site

New Reservoir Discoveries in Old Fields (Million Barrels) U.S. Federal Offshore Crude Oil + Lease Condensate New Reservoir Discoveries in Old Fields (Million Barrels) Decade Year-0...

338

U.S. Federal Offshore Crude Oil Reserves in Nonproducing Reservoirs...  

U.S. Energy Information Administration (EIA) Indexed Site

Reserves in Nonproducing Reservoirs (Million Barrels) U.S. Federal Offshore Crude Oil Reserves in Nonproducing Reservoirs (Million Barrels) Decade Year-0 Year-1 Year-2 Year-3...

339

E-Print Network 3.0 - ardross reservoir gridblock Sample Search...  

NLE Websites -- All DOE Office Websites (Extended Search)

sections. Reservoir Reservoir gridblock Idealized gridblockSingle matrix block Fracture Matrix 12;SPE... gridblocks is applied for ... Source: Arbogast, Todd - Center for...

340

Sensitivity analysis of modeling parameters that affect the dual peaking behaviour in coalbed methane reservoirs.  

E-Print Network (OSTI)

??Coalbed methane reservoir (CBM) performance is controlled by a complex set of reservoir, geologic, completion and operational parameters and the inter-relationships between those parameters. Therefore (more)

Okeke, Amarachukwu Ngozi

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

EVALUATION OF PERFORMANCE OF CYCLIC STEAM INJECTION IN NATURALLY FRACTURED RESERVOIRS AN ARTIFICIAL NEURAL NETWORK APPLICATION.  

E-Print Network (OSTI)

??With increasing demand on oil, it is important to improve the recovery factor of oil reservoirs. Naturally fractured reservoirs constitute a major portion of worlds (more)

Chintalapati, Santosh Phani Bhushan

2011-01-01T23:59:59.000Z

342

GHG Emissions from Hydropower Reservoirs The role of hydropower reservoirs in contributing to greenhouse gas (GHG) emissions is poorly  

E-Print Network (OSTI)

GHG Emissions from Hydropower Reservoirs The role of hydropower reservoirs in contributing to greenhouse gas (GHG) emissions is poorly understood, but recent studies have indicated that GHG emissions; and over 5 weeks in August--September, the peak GHG emission period, during 2012. (Pacific Northwest

343

Hyperspectral Aerosol Optical Depths from TCAP Flights  

SciTech Connect

4STAR (Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research), the worlds first hyperspectral airborne tracking sunphotometer, acquired aerosol optical depths (AOD) at 1 Hz during all July 2012 flights of the Two Column Aerosol Project (TCAP). Root-mean square differences from AERONET ground-based observations were 0.01 at wavelengths between 500-1020 nm, 0.02 at 380 and 1640 nm and 0.03 at 440 nm in four clear-sky fly-over events, and similar in ground side-by-side comparisons. Changes in the above-aircraft AOD across 3-km-deep spirals were typically consistent with integrals of coincident in situ (on DOE Gulfstream 1 with 4STAR) and lidar (on NASA B200) extinction measurements within 0.01, 0.03, 0.01, 0.02, 0.02, 0.02 at 355, 450, 532, 550, 700, 1064 nm, respectively, despite atmospheric variations and combined measurement uncertainties. Finer vertical differentials of the 4STAR measurements matched the in situ ambient extinction profile within 14% for one homogeneous column. For the AOD observed between 350-1660 nm, excluding strong water vapor and oxygen absorption bands, estimated uncertainties were ~0.01 and dominated by (then) unpredictable throughput changes, up to +/-0.8%, of the fiber optic rotary joint. The favorable intercomparisons herald 4STARs spatially-resolved high-frequency hyperspectral products as a reliable tool for climate studies and satellite validation.

Shinozuka, Yohei; Johnson, Roy R.; Flynn, Connor J.; Russell, P. B.; Schmid, Beat; Redemann, Jens; Dunagan, Stephen; Kluzek, Celine D.; Hubbe, John M.; Segal-Rosenheimer, Michal; Livingston, J. M.; Eck, T.; Wagener, Richard; Gregory, L.; Chand, Duli; Berg, Larry K.; Rogers, Ray; Ferrare, R. A.; Hair, John; Hostetler, Chris A.; Burton, S. P.

2013-11-13T23:59:59.000Z

344

Implications of the UHECRs penetration depth measurements  

E-Print Network (OSTI)

The simple interpretation of PAO's UHECRs' penetration depth measurements suggests a transition at the energy range $1.1 - 35 \\cdot 10^{18} $ eV from protons to heavier nuclei. A detailed comparison of this data with air shower simulations reveals strong restrictions on the amount of light nuclei (protons and He) in the observed flux. We find a robust upper bound on the observed proton fraction of the UHECRs flux and we rule out a composition dominated by protons and He. Acceleration and propagation effects lead to an observed composition that is different from the one at the source. Using a simple toy model that take into account these effects, we show that the observations requires an extreme metallicity at the sources with metals to protons mass ratio of 1:1, a ratio that is larger by a factor of a hundred than the solar abundance. This composition imposes an almost impossible constraint on all current astrophysical models for UHECRs accelerators. This may provide a first hint towards new physics that emerges at $\\sim 100$ TeV and leads to a larger proton cross section at these energies.

Nimrod Shaham; Tsvi Piran

2012-04-06T23:59:59.000Z

345

HIGH RESOLUTION PREDICTION OF GAS INJECTION PROCESS PERFORMANCE FOR HETEROGENEOUS RESERVOIRS  

SciTech Connect

This report outlines progress in the second 3 months of the first year of the DOE project ''High Resolution Prediction of Gas Injection Process Performance for Heterogeneous Reservoirs.'' The development of an automatic technique for analytical solution of one-dimensional gas flow problems with volume change on mixing is described. The aim of this work is to develop a set of ultra-fast compositional simulation tools that can be used to make field-scale predictions of the performance of gas injection processes. To achieve the necessary accuracy, these tools must satisfy the fundamental physics and chemistry of the displacement from the pore to the reservoir scales. Thus this project focuses on four main research areas: (1) determination of the most appropriate methods of mapping multicomponent solutions to streamlines and streamtubes in 3D; (2) development of techniques for automatic generation of analytical solutions for one-dimensional flow along a streamline; (3) experimental investigations to improve the representation of physical mechanisms that govern displacement efficiency along a streamline; and (4) theoretical and experimental investigations to establish the limitations of the streamline/streamtube approach. In this report they briefly review the status of the research effort in each area. They then give a more in depth discussion of their development of techniques for analytic solutions along a streamline including volume change on mixing for arbitrary numbers of components.

Franklin M. Orr, Jr.

2001-03-31T23:59:59.000Z

346

Naturally fractured tight gas reservoir detection optimization  

SciTech Connect

The goal of the work this quarter has been to partition and high-grade the Greater Green River basin for exploration efforts in the Upper Cretaceous tight gas play and to initiate resource assessment of the basin. The work plan for the quarter of July 1-September 30, 1998 comprised three tasks: (1) Refining the exploration process for deep, naturally fractured gas reservoirs; (2) Partitioning of the basin based on structure and areas of overpressure; (3) Examination of the Kinney and Canyon Creek fields with respect to the Cretaceous tight gas play and initiation of the resource assessment of the Vermilion sub-basin partition (which contains these two fields); and (4) Initiation analysis of the Deep Green River Partition with respect to the Stratos well and assessment of the resource in the partition.

NONE

1998-11-30T23:59:59.000Z

347

Naturally fractured tight gas reservoir detection optimization  

SciTech Connect

Building upon the partitioning of the Greater Green River Basin (GGRB) that was conducted last quarter, the goal of the work this quarter has been to conclude evaluation of the Stratos well and the prototypical Green River Deep partition, and perform the fill resource evaluation of the Upper Cretaceous tight gas play, with the goal of defining target areas of enhanced natural fracturing. The work plan for the quarter of November 1-December 31, 1998 comprised four tasks: (1) Evaluation of the Green River Deep partition and the Stratos well and examination of potential opportunity for expanding the use of E and P technology to low permeability, naturally fractured gas reservoirs, (2) Gas field studies, and (3) Resource analysis of the balance of the partitions.

NONE

1999-06-01T23:59:59.000Z

348

Naturally fractured tight gas reservoir detection optimization  

SciTech Connect

During this quarter, work began on the regional structural and geologic analysis of the greater Green River basin (GGRB) in southwestern Wyoming, northwestern Colorado and northeastern Utah. The ultimate objective of the regional analysis is to apply the techniques developed and demonstrated during earlier phases of the project to sweet-spot delineation in a relatively new and underexplored play: tight gas from continuous-type Upper Cretaceous reservoirs of the GGRB. The primary goal of this work is to partition and high-grade the greater Green River basin for exploration efforts in the Cretaceous tight gas play. The work plan for the quarter of January 1, 1998--March 31, 1998 consisted of three tasks: (1) Acquire necessary data and develop base map of study area; (2) Process data for analysis; and (3) Initiate structural study. The first task and second tasks were completed during this reporting period. The third task was initiated and work continues.

NONE

1998-09-30T23:59:59.000Z

349

Eighteenth workshop on geothermal reservoir engineering: Proceedings  

SciTech Connect

PREFACE The Eighteenth Workshop on Geothermal Reservoir Engineering was held at Stanford University on January 26-28, 1993. There were one hundred and seventeen registered participants which was greater than the attendance last year. Participants were from eight foreign countries: Italy, Japan, United Kingdom, Mexico, New Zealand, the Philippines, Guatemala, and Iceland. Performance of many geothermal fields outside the United States was described in several of the papers. Dean Gary Ernst opened the meeting and welcomed the visitors to the campus. The key note speaker was J.E. ''Ted'' Mock who gave a brief overview of the Department of Energy's current plan. The Stanford Geothermal Program Reservoir Engineering Award for Excellence in Development of Geothermal Energy was awarded to Dr. Mock who also spoke at the banquet. Thirty-nine papers were presented at the Workshop with two papers submitted for publication only. Technical papers were organized in twelve sessions concerning: field operations, The Geysers, geoscience, hot-dry-rock, injection, modeling, slim hole wells, geochemistry, well test and wellbore. Session chairmen were major contributors to the program and we thank: John Counsil, Kathleen Enedy, Harry Olson, Eduardo Iglesias, Marcelo Lippmann, Paul Atkinson, Jim Lovekin, Marshall Reed, Antonio Correa, and David Faulder. The Workshop was organized by the Stanford Geothermal Program faculty, staff, and graduate students. We wish to thank Pat Ota, Ted Sumida, and Terri A. Ramey who also produces the Proceedings Volumes for publication. We owe a great deal of thanks to our students who operate audiovisual equipment and to John Hornbrook who coordinated the meeting arrangements for the Workshop. Henry J. Ramey, Jr. Roland N. Horne Frank G. Miller Paul Kruger William E. Brigham Jean W. Cook

Ramey, H.J. Jr.; Horne, R.J.; Kruger, P.; Miller, F.G.; Brigham, W.E.; Cook, J.W. (Stanford Geothermal Program)

1993-01-28T23:59:59.000Z

350

Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material  

NLE Websites -- All DOE Office Websites (Extended Search)

0: March 8, 2004 0: March 8, 2004 Average Material Consumption for a Domestic Automobile to someone by E-mail Share Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Facebook Tweet about Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Twitter Bookmark Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Google Bookmark Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Delicious Rank Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Digg Find More places to share Vehicle Technologies Office: Fact #310:

351

Average Interest Rate for Treasury Securities | Data.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

Average Interest Rate for Treasury Securities Average Interest Rate for Treasury Securities Consumer Data Apps Challenges Resources About Blogs Let's Talk Feedback Consumer You are here Data.gov » Communities » Consumer » Data Average Interest Rate for Treasury Securities Dataset Summary Description This dataset shows the average interest rates for U.S Treasury securities for the most recent month compared with the same month of the previous year. The data is broken down by the various marketable and non-marketable securities. The summary page for the data provides links for monthly reports from 2001 through the current year. Average Interest Rates are calculated on the total unmatured interest-bearing debt. The average interest rates for total marketable, total non-marketable and total interest-bearing debt do not include the U.S. Treasury Inflation-Protected Securities.

352

Solar: monthly and annual average global horizontal (GHI) GIS...  

Open Energy Info (EERE)

Facebook icon Twitter icon Home Organizations DLR - Deutsches Zentrum fr ... Solar: monthly and annual ... Dataset Activity Stream Solar: monthly and annual average...

353

,"Selected National Average Natural Gas Prices"  

U.S. Energy Information Administration (EIA) Indexed Site

Selected National Average Natural Gas Prices" Selected National Average Natural Gas Prices" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","Average Natural Gas Prices",11,"Monthly","11/2013","1/15/1973" ,"Data 2","Annual Average Natural Gas Prices",11,"Annual",2012,"6/30/1922" ,"Release Date:","12/12/2013" ,"Next Release Date:","1/7/2014" ,"Excel File Name:","ngm03vmall.xls" ,"Available from Web Page:","http://www.eia.gov/oil_gas/natural_gas/data_publications/natural_gas_monthly/ngm.html"

354

Submarine fan lobe models: Implications for reservoir properties  

SciTech Connect

A multitude of submarine fan lobe models, advocating widely different reservoir properties, has been introduced into the sedimentologic literature. Four of these models are compared to show their differences in reservoir properties. Braided suprafan lobes are characterized by stacked sand bodies with good lateral and vertical communication, and they constitute excellent reservoir facies. The unchanneled depositional lobes, composed of sheetlike sand bodies with good lateral and moderate vertical communication, exhibit properties of good reservoir facies. Fanlobes, which refer to meandering channels and associated levee facies of large mud-rich submarine fans such as the Mississippi Fan in the Gulf of Mexico, are characterized by offset stacked sand bodies with poor lateral and vertical communication. These lenticular sands have the potential to be moderately good reservoir facies. Ponded lobes, which represent mud-rich slump facies of slope environments, comprise poor reservoir facies because of poor sand content and poor sand-body connectivity caused by chaotic bedding. Furthermore, the presence of slumped mud layers in ponded lobes is expected to hinder fluid flow. Because different lobe models vary significantly from one another in terms of reservoir properties, caution must be exercised to apply the proper lobe model to ancient fan sequences in hydrocarbon exploration and production.

Shanmugam, G.; Moiola, R.J. (Mobil Research and Development Corp., Dallas, TX (USA))

1990-09-01T23:59:59.000Z

355

Putting integrated reservoir characterization into practice - in house training  

SciTech Connect

The need for even more efficient reservoir characterization and management has forced a change in the way Mobil Oil provides technical support to its production operations. We`ve learned that to be successful, a good understanding of the reservoir is essential. This includes an understanding of the technical and business significance of reservoir heterogeneities at different stages of field development. A multi-disciplinary understanding of the business of integrated reservoir characterization is essential and to facilitate this understanding, Mobil has developed a highly successful {open_quotes}Reservoir Characterization Field Seminar{close_quotes}. Through specific team based case studies that incorporate outcrop examples and data the program provides participants the opportunity to explore historic and alternative approaches to reservoir description, characterization and management. We explore appropriate levels and timing of data gathering, technology applications, risk assessment and management practices at different stages of field development. The case studies presented throughout the course are a unique element of the program which combine real life and hypothetical problem sets that explore how different technical disciplines interact, the approaches to a problem solving they use, the assumptions and uncertainties contained in their contributions and the impact those conclusions may have on other disciplines involved in the overall reservoir management process. The team building aspect of the course was an added bonus.

Wright, F.M. Jr.; Best, D.A.; Clarke, R.T. [Mobile Exploration and Producing Technical Center, Dallas, TX (United States)

1997-08-01T23:59:59.000Z

356

Frio sandstone reservoirs in the deep subsurface along the Texas Gulf Coast: their potential for production of geopressured geothermal energy  

SciTech Connect

Detailed geological, geophysical, and engineering studies conducted on the Frio Formation have delineated a geothermal test well site in the Austin Bayou Prospect which extends over an area of 60 square miles. A total of 800 to 900 feet of sandstone will occur between the depths of 13,500 and 16,500 feet. At leat 30 percent of the sand will have core permeabilities of 20 to 60 millidarcys. Temperature at the top of the sandstone section will be 300/sup 0/F. Water, produced at a rate of 20,000 to 40,000 barrels per day, will probably have to be disposed of by injection into shallower sandstone reservoirs. More than 10 billion barrels of water are in place in these sandstone reservoirs of the Austin Bayou Prospect; there should be approximately 400 billion cubic feet of methane in solution in this water. Only 10 percent of the water and methane (1 billion barrels of water and 40 billion cubic feet of methane) will be produced without reinjection of the waste water into the producing formation. Reservoir simulation studies indicate that 90 percent of the methane can be produced with reinjection. 106 figures.

Bebout, D.G.; Loucks, R.G.; Gregory, A.R.

1983-01-01T23:59:59.000Z

357

Recovery of SIMS depth profiles with account for nonstationary effects  

Science Journals Connector (OSTI)

Abstract In this work we consider a method of accounting for the nonstationary effects in recovery of SIMS depth profiles. The depth resolution function (DRF) is described by Hofmann's nonstationary MRI (mixing-roughness-information depth) model using the depth-dependent parameters. The effects in question include the nonstationary atomic mixing and development of surface roughness. A mathematical description of the nonstationary depth profiling process by the Fredholm integral equation of the first kind is proposed. The inverse problem is solved using an algorithm based on the Tikhonov regularization method. The proposed nonstationary recovery method is tested on both model and real structures. The development of surface roughness in SIMS depth profiling of the real structure was observed. Grazing incidence x-ray reflectometry (XRR) technique was used to verify the results of SIMS profiles restoration for periodic structure containing thin Ge layers in the Si matrix. The advantages of the proposed recovery algorithm to allow for the nonstationary effects are shown.

Pavel Andreevich Yunin; Yurii Nikolaevich Drozdov; Mikhail Nikolaevich Drozdov; Dmitry Vladimirovich Yurasov

2014-01-01T23:59:59.000Z

358

Underground Gas Storage Reservoirs (West Virginia) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Gas Storage Reservoirs (West Virginia) Gas Storage Reservoirs (West Virginia) Underground Gas Storage Reservoirs (West Virginia) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Program Info State West Virginia Program Type Safety and Operational Guidelines Provider West Virginia Department of Commerce Lays out guidelines for the conditions under which coal mining operations must notify state authorities of intentions to mine where underground gas

359

Borehole geophysics evaluation of the Raft River geothermal reservoir,  

Open Energy Info (EERE)

reservoir, reservoir, Idaho Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Borehole geophysics evaluation of the Raft River geothermal reservoir, Idaho Details Activities (1) Areas (1) Regions (0) Abstract: GEOTHERMAL ENERGY; GEOTHERMAL FIELDS; GEOPHYSICAL SURVEYS; RAFT RIVER VALLEY; GEOTHERMAL EXPLORATION; BOREHOLES; EVALUATION; HOT-WATER SYSTEMS; IDAHO; MATHEMATICAL MODELS; WELL LOGGING; CAVITIES; EXPLORATION; GEOTHERMAL SYSTEMS; HYDROTHERMAL SYSTEMS; NORTH AMERICA; PACIFIC NORTHWEST REGION; USA Author(s): Applegate, J.K.; Donaldson, P.R.; Hinkley, D.L.; Wallace, T.L. Published: Geophysics, 2/1/1977 Document Number: Unavailable DOI: Unavailable Source: View Original Journal Article Geophysical Method At Raft River Geothermal Area (1977) Raft River Geothermal Area

360

Tarmat behavior calculated for reservoir with sealing fault  

SciTech Connect

The Minagish Oolite oil reservoir in Kuwait is one of many Middle East reservoirs characterized by the presence of a tarmat (heavy to tar-like crude) at the oil-water contact. Since a waterflood project is planned for the Minagish Oolite, which contains a radial pattern of faults, a study was made to consider tarmat behavior upon water injection below it when the injection well is located near a sealing fault. The study resulted in a technique to predict the time of tarmat breakdown, response time at the nearest observation well, and differential pressure at the tarmat anywhere in the reservoir.

Osman, M.E.S.

1986-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Recreation land policies of Texas river authorities operating reservoirs  

E-Print Network (OSTI)

for future water in Texas by the Texas Department of Water Resources: Present use of lakes and reservoirs for water- oriented recreation demonstrates the need to include recreation as one of the many purposes of water 13 development projects... by the reservoir owner. 26 3. Another factor is that most reservoir owners do not let the1r land stand idle. Uses are found which either increase the benefits of the project' to the owner or public, or at least balance the costs of holding the land pending...

Ruesink, Lou Ellen

1979-01-01T23:59:59.000Z

362

Advanced Oil Recovery Technologies for Improved Recovery from Slope Basin Clastic Reservoirs, Nash Draw Brushy Canyon Pool, Eddy County, NM  

SciTech Connect

The Nash Draw Brushy Canyon Pool in Eddy County New Mexico was a cost-shared field demonstration project in the U.S. Department of Energy Class III Program. A major goal of the Class III Program was to stimulate the use of advanced technologies to increase ultimate recovery from slope-basin clastic reservoirs. Advanced characterization techniques were used at the Nash Draw Pool (NDP) project to develop reservoir management strategies for optimizing oil recovery from this Delaware reservoir. The objective of the project was to demonstrate that a development program, which was based on advanced reservoir management methods, could significantly improve oil recovery at the NDP. Initial goals were (1) to demonstrate that an advanced development drilling and pressure maintenance program can significantly improve oil recovery compared to existing technology applications and (2) to transfer these advanced methodologies to other oil and gas producers. Analysis, interpretation, and integration of recently acquired geological, geophysical, and engineering data revealed that the initial reservoir characterization was too simplistic to capture the critical features of this complex formation. Contrary to the initial characterization, a new reservoir description evolved that provided sufficient detail regarding the complexity of the Brushy Canyon interval at Nash Draw. This new reservoir description was used as a risk reduction tool to identify 'sweet spots' for a development drilling program as well as to evaluate pressure maintenance strategies. The reservoir characterization, geological modeling, 3-D seismic interpretation, and simulation studies have provided a detailed model of the Brushy Canyon zones. This model was used to predict the success of different reservoir management scenarios and to aid in determining the most favorable combination of targeted drilling, pressure maintenance, well stimulation, and well spacing to improve recovery from this reservoir. An Advanced Log Analysis technique developed from the NDP project has proven useful in defining additional productive zones and refining completion techniques. This program proved to be especially helpful in locating and evaluating potential recompletion intervals, which has resulted in low development costs with only small incremental increases in lifting costs. To develop additional reserves at lower costs, zones behind pipe in existing wells were evaluated using techniques developed for the Brushy Canyon interval. These techniques were used to complete uphole zones in thirteen of the NDP wells. A total of 14 recompletions were done: four during 1999, four during 2000, two during 2001, and four during 2002-2003. These workovers added reserves of 332,304 barrels of oil (BO) and 640,363 MCFG (thousand cubic feet of gas) at an overall weighted average development cost of $1.87 per BOE (barrel of oil equivalent). A pressure maintenance pilot project in a developed area of the field was not conducted because the pilot area was pressure depleted, and the reservoir in that area was found to be compartmentalized and discontinuous. Economic analyses and simulation studies indicated that immiscible injection of lean hydrocarbon gas for pressure maintenance was not warranted at the NDP and would need to be considered for implementation in similar fields very soon after production has started. Simulation studies suggested that the injection of miscible carbon dioxide (CO{sub 2}) could recover significant quantities of oil at the NDP, but a source of low-cost CO{sub 2} was not available in the area. Results from the project indicated that further development will be under playa lakes and potash areas that were beyond the regions covered by well control and are not accessible with vertical wells. These areas, covered by 3-D seismic surveys that were obtained as part of the project, were accessed with combinations of deviated/horizontal wells. Three directional/horizontal wells have been drilled and completed to develop reserves under surface-restricted areas and potash mines. The third

Mark B. Murphy

2005-09-30T23:59:59.000Z

363

Higher-order averaging, formal series and numerical integration II  

E-Print Network (OSTI)

systems of ordinary differential equations with d 1 non- resonant constant frequencies. Formal series frequency and four resonant fast frequencies. Keywords and sentences: Averaging, high-order averaging, quasi Schumann, 35170 Bruz, France. Email: Philippe.Chartier@inria.fr Konputazio Zientziak eta A. A. Saila

Murua, Ander

364

Effects of soil quality and depth on seed germination and seedling survival at the Nevada test site  

SciTech Connect

The Nuclear Waste Policy Act, as amended in 1987, directs the US Department of Energy (DOE) to study Yucca Mountain, in southern Nevada, as a potential site for long-term storage of high-level nuclear waste. DOE policy mandates the restoration of all lands disturbed by site characterization activities and DOE has developed an environmental program that is to be implemented during site characterization activities at Yucca.Mountain. DOE is currently conducting reclamation feasibility trials as part of this environmental program. No topsoil was saved on disturbances during early site investigation and minimal soil remains at existing disturbances on Yucca Mountain. A study was developed to test the effects of soil quality and depth on seedling emergence and survival. A series of plots was established and two treatments were tested. The first treatment compared native topsoil to subsoil imported from a borrow pit. The second treatment compared four different depth ranges of both soil types. All plots received identical seeding treatments. Seedling density was measured after emergence. Overall seedling densities were low, averaging 10.3 {plus_minus} 8.8 (SD) plants/m{sup 2}. Statistical analysis revealed a significant interaction between the two treatment factors. The subsoil had increasing densities from the deep soil depths to the shallow depths while the topsoil had increasing densities from the shallow soil depths to the deep depths. The cause of this interaction may have resulted from the bedrock being close to the soil surface of the shallow plots.

Blomquist, K.W.; Lyon, G.E.

1993-12-31T23:59:59.000Z

365

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

East Asia from NREL East Asia from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water

366

Do Diurnal Aerosol Changes Affect Daily Average Radiative Forcing?  

SciTech Connect

Strong diurnal variability of aerosol has been observed frequently for many urban/industrial regions. How this variability may alter the direct aerosol radiative forcing (DARF), however, is largely unknown. To quantify changes in the time-averaged DARF, we perform an assessment of 29 days of high temporal resolution ground-based data collected during the Two-Column Aerosol Project (TCAP) on Cape Cod, which is downwind of metropolitan areas. We demonstrate that strong diurnal changes of aerosol loading (about 20% on average) have a negligible impact on the 24-h average DARF, when daily averaged optical properties are used to find this quantity. However, when there is a sparse temporal sampling of aerosol properties, which may preclude the calculation of daily averaged optical properties, large errors (up to 100%) in the computed DARF may occur. We describe a simple way of reducing these errors, which suggests the minimal temporal sampling needed to accurately find the forcing.

Kassianov, Evgueni I.; Barnard, James C.; Pekour, Mikhail S.; Berg, Larry K.; Michalsky, Joseph J.; Lantz, K.; Hodges, G. B.

2013-06-17T23:59:59.000Z

367

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

Africa from NREL Africa from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water

368

Defense-in-Depth, How Department of Energy Implements Radiation...  

Office of Environmental Management (EM)

is implemented using a defense-in-depth approach taking into account the combination of natural and engineered barriers, performance objectives, long-term risk assessments,...

369

Advanced Technology Vehicle Lab Benchmarking - Level 2 (in-depth...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Evaluation Meeting vss031rask2012o.pdf More Documents & Publications Advanced Technology Vehicle Lab Benchmarking - Level 2 (in-depth) Advanced Technology Vehicle Lab...

370

Are Cluster Ion Analysis Beams Good Choices for Hydrogen Depth...  

NLE Websites -- All DOE Office Websites (Extended Search)

Cluster Ion Analysis Beams Good Choices for Hydrogen Depth Profiling Using Time-of-Flight Secondary Ion Mass Spectrometry? Are Cluster Ion Analysis Beams Good Choices for Hydrogen...

371

Control Systems Cyber Security: Defense in Depth Strategies ...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

that use control system networks while maintaining a multi-tier information architecture. Control Systems Cyber Security: Defense in Depth Strategies More Documents &...

372

BOUDREAU, BERNARD P. Mean mixed depth of sediments: The ...  

Science Journals Connector (OSTI)

bioturbation. Bioturbation is the mixing of surficial sediments as a re- sult of the activity .... that the mixed depth is limited by the increasing energy costs of deeper

2000-10-17T23:59:59.000Z

373

Averaged dynamics of ultra-relativisitc charged particles beams  

E-Print Network (OSTI)

In this thesis, we consider the suitability of using the charged cold fluid model in the description of ultra-relativistic beams. The method that we have used is the following. Firstly, the necessary notions of kinetic theory and differential geometry of second order differential equations are explained. Then an averaging procedure is applied to a connection associated with the Lorentz force equation. The result of this averaging is an affine connection on the space-time manifold. The corresponding geodesic equation defines the averaged Lorentz force equation. We prove that for ultra-relativistic beams described by narrow distribution functions, the solutions of both equations are similar. This fact justifies the replacement of the Lorentz force equation by the simpler {\\it averaged Lorentz force equation}. After this, for each of these models we associate the corresponding kinetic model, which are based on the Vlasov equation and {\\it averaged Vlasov equation} respectively. The averaged Vlasov equation is simpler than the original Vlasov equation. This fact allows us to prove that the differential operation defining the averaged charged cold fluid equation is controlled by the {\\it diameter of the distribution function}, by powers of the {\\it energy of the beam} and by the time of evolution $t$. We show that the Vlasov equation and the averaged Vlasov equation have similar solutions, when the initial conditions are the same. Finally, as an application of the {\\it averaged Lorentz force equation} we re-derive the beam dynamics formalism used in accelerator physics from the Jacobi equation of the averaged Lorentz force equation.

Ricardo Gallego Torrom

2012-06-19T23:59:59.000Z

374

Sixteenth workshop on geothermal reservoir engineering: Proceedings  

SciTech Connect

The Sixteenth Workshop on Geothermal Reservoir Engineering was held at Stanford University on January 23-25, 1991. The Workshop Banquet Speaker was Dr. Mohinder Gulati of UNOCAL Geothermal. Dr. Gulati gave an inspiring talk on the impact of numerical simulation on development of geothermal energy both in The Geysers and the Philippines. Dr. Gulati was the first recipient of The Stanford Geothermal Program Reservoir Engineering Award for Excellence in Development of Geothermal Energy. Dr. Frank Miller presented the award. The registered attendance figure of one hundred fifteen participants was up slightly from last year. There were seven foreign countries represented: Iceland, Italy, Philippines, Kenya, the United Kingdom, Mexico, and Japan. As last year, papers on about a dozen geothermal fields outside the United States were presented. There were thirty-six papers presented at the Workshop, and two papers were submitted for publication only. Attendees were welcomed by Dr. Khalid Aziz, Chairman of the Petroleum Engineering Department at Stanford. Opening remarks were presented by Dr. Roland Horne, followed by a discussion of the California Energy Commission's Geothermal Activities by Barbara Crowley, Vice Chairman; and J.E. ''Ted'' Mock's presentation of the DOE Geothermal Program: New Emphasis on Industrial Participation. Technical papers were organized in twelve sessions concerning: hot dry rock, geochemistry, tracer injection, field performance, modeling, and chemistry/gas. As in previous workshops, session chairpersons made major contributions to the program. Special thanks are due to Joel Renner, Jeff Tester, Jim Combs, Kathy Enedy, Elwood Baldwin, Sabodh Garg, Marcel0 Lippman, John Counsil, and Eduardo Iglesias. The Workshop was organized by the Stanford Geothermal Program faculty, staff, and graduate students. We wish to thank Pat Ota, Angharad Jones, Rosalee Benelli, Jeanne Mankinen, Ted Sumida, and Terri A. Ramey who also produces the Proceedings Volumes for publication. We owe a great deal of thanks to our students who operate the audiovisual equipment and to Michael Riley who coordinated the meeting arrangements for a second year. Henry J. Ramey, Jr. Roland N. Horne Frank G. Miller Paul Kruger William E. Brigham Jean W. Cook

Ramey, H.J. Jr.; Kruger, P.; Miller, F.G.; Horne, R.N.; Brigham, W.E.; Cook, J.W. (Stanford Geothermal Program) [Stanford Geothermal Program

1991-01-25T23:59:59.000Z

375

The Role of Geochemistry and Stress on Fracture Development and Proppant Behavior in EGS Reservoirs  

Energy.gov (U.S. Department of Energy (DOE))

Project objective: Develop Improved Methods For Maintaining Permeable Fracture Volumes In EGS Reservoirs.

376

Robust Optimization of Oil Reservoir Flooding G.M. van Essen, M.J. Zandvliet,  

E-Print Network (OSTI)

Robust Optimization of Oil Reservoir Flooding G.M. van Essen, M.J. Zandvliet, P.M.J. Van den Hof the reservoir to the subsurface. The injection wells inject water into the oil reservoir with the aim to push reservoirs, the oil-water front does not travel uniformly towards the pro- duction wells, but is usually

Van den Hof, Paul

377

Bayes Linear Uncertainty Analysis for Oil Reservoirs Based on Multiscale Computer Experiments  

E-Print Network (OSTI)

Bayes Linear Uncertainty Analysis for Oil Reservoirs Based on Multiscale Computer Experiments, 2008 1 Introduction Reservoir simulators are important and widely-used tools for oil reservoir for reservoirs, where the model inputs are physical parameters, such as the permeability and porosity of various

Oakley, Jeremy

378

Geothermal reservoir temperatures estimated from the oxygen isotope  

Open Energy Info (EERE)

reservoir temperatures estimated from the oxygen isotope reservoir temperatures estimated from the oxygen isotope compositions of dissolved sulfate and water from hot springs and shallow drillholes Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Geothermal reservoir temperatures estimated from the oxygen isotope compositions of dissolved sulfate and water from hot springs and shallow drillholes Details Activities (3) Areas (3) Regions (0) Abstract: The oxygen isotope compositions of dissolved sulfate and water from hot springs and shallow drillholes have been tested as a geothermometer in three areas of the western United States. Limited analyses of spring and borehole fluids and existing experimental rate studies suggest that dissolved sulfate and water are probably in isotopic equilibrium in all reservoirs of significant size with temperatures above

379

FLUID INCLUSION STRATIGRAPHY: NEW METHOD FOR GEOTHERMAL RESERVOIR  

Open Energy Info (EERE)

FLUID INCLUSION STRATIGRAPHY: NEW METHOD FOR GEOTHERMAL RESERVOIR FLUID INCLUSION STRATIGRAPHY: NEW METHOD FOR GEOTHERMAL RESERVOIR ASSESSMENT PRELIMINARY RESULTS Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: FLUID INCLUSION STRATIGRAPHY: NEW METHOD FOR GEOTHERMAL RESERVOIR ASSESSMENT PRELIMINARY RESULTS Details Activities (1) Areas (1) Regions (0) Abstract: Fluid Inclusion Stratigraphy (FIS) is a new technique developed for the oil industry in order to map borehole fluids. This method is being studied for application to geothermal wells and is funded by the California Energy Commission. Fluid inclusion gas geochemistry is analyzed and plotted on well log diagrams. The working hypothesis is that select gaseous species and species ratios indicate areas of groundwater and reservoir fluid flow

380

Shear-wave splitting and reservoir crack characterization: the Coso  

Open Energy Info (EERE)

Shear-wave splitting and reservoir crack characterization: the Coso Shear-wave splitting and reservoir crack characterization: the Coso geothermal field Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Shear-wave splitting and reservoir crack characterization: the Coso geothermal field Details Activities (1) Areas (1) Regions (0) Abstract: This paper aims to improve current understanding of the subsurface fracture system in the Coso geothermal field, located in east-central California. The Coso reservoir is in active economic development, so that knowledge of the subsurface fracture system is of vital importance for an accurate evaluation of its geothermal potential and day-to-day production. To detect the geometry and density of fracture systems we applied the shear-wave splitting technique to a large number of

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Property:SanyalTempReservoir | Open Energy Information  

Open Energy Info (EERE)

SanyalTempReservoir SanyalTempReservoir Jump to: navigation, search Property Name SanyalTempReservoir Property Type Page Description see Sanyal_Temperature_Classification Allows Values Extremely Low Temperature;Very Low Temperature;Low Temperature;Moderate Temperature;High Temperature;Ultra High Temperature;Steam Field Pages using the property "SanyalTempReservoir" Showing 16 pages using this property. A Amedee Geothermal Area + Very Low Temperature + B Beowawe Hot Springs Geothermal Area + Moderate Temperature + Blue Mountain Geothermal Area + High Temperature + C Chena Geothermal Area + Very Low Temperature + D Desert Peak Geothermal Area + Moderate Temperature + K Kilauea East Rift Geothermal Area + High Temperature + L Lightning Dock Geothermal Area + High Temperature +

382

EIS-0404: Los Vaqueros Reservoir Expansion Project, California | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

404: Los Vaqueros Reservoir Expansion Project, California 404: Los Vaqueros Reservoir Expansion Project, California EIS-0404: Los Vaqueros Reservoir Expansion Project, California Summary This EIS/Environmental Impact Report was prepared by the Department of the Interior (Bureau of Reclamation, Mid-Pacific Region) and the Contra Costa Water District to evaluate the environmental impacts of a proposal to enlarge the existing Los Vaqueros Reservoir in Contra Costa County, California. DOE's Western Area Power Administration (Western) was a cooperating agency because it has jurisdiction over transmission facilities that were expected to be relocated under the proposed action. Based on project changes, however, Western has no action and therefore will not adopt the EIS or issue a ROD. Public Comment Opportunities No public comment opportunities available at this time.

383

Reservoir-Scale Fracture Permeability in the Dixie Valley, Nevada,  

Open Energy Info (EERE)

Reservoir-Scale Fracture Permeability in the Dixie Valley, Nevada, Reservoir-Scale Fracture Permeability in the Dixie Valley, Nevada, Geothermal Field Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Reservoir-Scale Fracture Permeability in the Dixie Valley, Nevada, Geothermal Field Abstract Borehole televiewer, temperature, and flowmeter datarecorded in six wells penetrating a geothermalreservoir associated with the Stillwater fault zone inDixie Valley, Nevada, were used to investigate therelationship between reservoir permeability and thecontemporary in situ stress field. Data from wellsdrilled into productive and nonproductive segments ofthe Stillwater fault zone indicate that permeability inall wells is dominated by a relatively small number offractures striking parallel to the local trend of

384

Use Of Electrical Surveys For Geothermal Reservoir Characterization-  

Open Energy Info (EERE)

Use Of Electrical Surveys For Geothermal Reservoir Characterization- Use Of Electrical Surveys For Geothermal Reservoir Characterization- Beowawe Geothermal Field Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Paper: Use Of Electrical Surveys For Geothermal Reservoir Characterization- Beowawe Geothermal Field Details Activities (4) Areas (1) Regions (0) Abstract: The STAR geothermal reservoir simulator was used to model the natural state of the Beowawe geothermal field, and to compute the subsurface distributions of temperature and salinity which were in turn employed to calculate pore-fluid resistivity. Archie's law, which relates formation resistivity to porosity and pore-fluid resistivity, was adopted to infer formation resistivity distribution. Subsequently, DC, MT and SP postprocessors were used to compute the expected response corresponding to

385

Characterization of Fractures in Geothermal Reservoirs Using Resistivity |  

Open Energy Info (EERE)

Characterization of Fractures in Geothermal Reservoirs Using Resistivity Characterization of Fractures in Geothermal Reservoirs Using Resistivity Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Characterization of Fractures in Geothermal Reservoirs Using Resistivity Abstract The optimal design of production in fractured geothermal reservoirs requires knowledge of the resource's connectivity, therefore making fracture characterization highly important. This study aims to develop methodologies to use resistivity measurements to infer fracture properties in geothermal fields. The resistivity distribution in the field can be estimated by measuring potential differences between various points and the data can then be used to infer fracture properties due to the contrast in resistivity between water and rock.

386

Sunset Reservoir Solar Power Plant | Open Energy Information  

Open Energy Info (EERE)

Reservoir Solar Power Plant Reservoir Solar Power Plant Jump to: navigation, search Name Sunset Reservoir Solar Power Plant Facility Sunset Reservoir Sector Solar Facility Type Photovoltaic Developer Recurrent Energy Location San Francisco, California Coordinates 37.7749295°, -122.4194155° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.7749295,"lon":-122.4194155,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

387

Hydrologic Properties of the Dixie Valley, Nevada, Geothermal Reservoir  

Open Energy Info (EERE)

Hydrologic Properties of the Dixie Valley, Nevada, Geothermal Reservoir Hydrologic Properties of the Dixie Valley, Nevada, Geothermal Reservoir from Well-Test Analyses Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Hydrologic Properties of the Dixie Valley, Nevada, Geothermal Reservoir from Well-Test Analyses Abstract Temperature, pressure, and spinner (TPS) logs have been recorded in several wells from the Dixie Valley Geothermal Reservoir in west central Nevada. A variety of well-test analyses has been performed with these data to quantify the hydrologic properties of this fault-dominated geothermal resource. Four complementary analytical techniques were employed, their individual application depending upon availability and quality of data and validity of scientific assumptions. In some instances, redundancy in

388

Exploration model for possible geothermal reservoir, Coso Hot Springs KGRA,  

Open Energy Info (EERE)

model for possible geothermal reservoir, Coso Hot Springs KGRA, model for possible geothermal reservoir, Coso Hot Springs KGRA, Inyo Co. , California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: Exploration model for possible geothermal reservoir, Coso Hot Springs KGRA, Inyo Co. , California Details Activities (1) Areas (1) Regions (0) Abstract: The purpose of this study was to test the hypothesis that a steam-filled fracture geothermal reservoir exists at Coso Hot Springs KGRA, as proposed by Combs and Jarzabek (1977). Gravity data collected by the USGS (Isherwood and Plouff, 1978) was plotted and compared with the geology of the area, which is well known. An east-west trending Bouguer gravity profile was constructed through the center of the heat flow anomaly described by Combs (1976). The best fit model for the observed gravity at

389

Shale Oil Production Performance from a Stimulated Reservoir Volume  

E-Print Network (OSTI)

The horizontal well with multiple transverse fractures has proven to be an effective strategy for shale gas reservoir exploitation. Some operators are successfully producing shale oil using the same strategy. Due to its higher viscosity and eventual...

Chaudhary, Anish Singh

2011-10-21T23:59:59.000Z

390

Scattering Characteristics In Heterogeneous Fractured Reservoirs From Waveform Estimation  

E-Print Network (OSTI)

Offset-dependent characteristics of seismic scattering are useful in the interpretation of fractured reservoirs. Synthetic seismograms generated by a 3-D finite difference modeling are used to study elastic wave propagation ...

Shen, Feng

1998-01-01T23:59:59.000Z

391

The Role of Acidizing in Proppant Fracturing in Carbonate Reservoirs  

E-Print Network (OSTI)

of the most widely considered alternatives for application in carbonate reservoirs. Especially in areas that have high closure stress, the non-smoothly etched surface created by acid fracturing may not remain open upon closing, resulting in decrease...

Densirimongkol, Jurairat

2010-10-12T23:59:59.000Z

392

Acidizing of Sandstone Reservoirs Using HF and Organic Acids  

E-Print Network (OSTI)

Mud acid, which is composed of HCl and HF, is commonly used to remove the formation damage in sandstone reservoirs. However, many problems are associated with HCl, especially at high temperatures. Formic-HF acids have served as an alternative...

Yang, Fei

2012-10-19T23:59:59.000Z

393

REVIEW PLAN John Redmond Dam Reservoir, Coffee County, Kansas  

E-Print Network (OSTI)

#12;#12;REVIEW PLAN John Redmond Dam Reservoir, Coffee County, Kansas Reallocation Study Tulsa...................................................................................................................11 12. REVIEW PLAN APPROVAL AND UPDATES........................................................................................11 13. REVIEW PLAN POINTS OF CONTACT

US Army Corps of Engineers

394

Reservoir Characterization with Limited Sample Data using Geostatistics  

E-Print Network (OSTI)

Kansas City Formation. The main tool of the study was geostatistics, since only geostatistics can incorporate data from variety of sources to estimate reservoir properties. Three different subjects in geostatistical methods were studied, analyzed...

Ghoraishy, Sayyed Mojtaba

2008-01-01T23:59:59.000Z

395

Heavy oil reservoirs recoverable by thermal technology. Annual report  

SciTech Connect

This volume contains reservoir, production, and project data for target reservoirs thermally recoverable by steam drive which are equal to or greater than 2500 feet deep and contain heavy oil in the 8 to 25/sup 0/ API gravity range. Data were collected from three source types: hands-on (A), once-removed (B), and twice-removed (C). In all cases, data were sought depicting and characterizing individual reservoirs as opposed to data covering an entire field with more than one producing interval or reservoir. The data sources are listed at the end of each case. This volume also contains a complete listing of operators and projects, as well as a bibliography of source material.

Kujawa, P.

1981-02-01T23:59:59.000Z

396

Optimal Fuzzy Management of Reservoir based on Genetic Algorithm  

Science Journals Connector (OSTI)

This chapter deals with water resource management problems faced from an Automatic Control point of view. The motivation for the study is the need for an automated management policy for an artificial reservoir...

Alberto Cavallo; Armando Di Nardo

2008-01-01T23:59:59.000Z

397

Optimising hydraulic fracture treatments in reservoirs under complex conditions.  

E-Print Network (OSTI)

??Growing global energy demand has prompted the exploitation of non-conventional resources such as Coal Bed Methane (CBM) and conventional resources such as gas-condensate reservoirs. Exploitation (more)

Valencia, Karen Joy

2005-01-01T23:59:59.000Z

398

Problems of fluid flow in a deformable reservoir  

E-Print Network (OSTI)

itself and the surrounding rock mass. The change in the stress-strain state of the system is induced by pressure change in the layers of the reservoir. Numerical results qualitatively agree with observed field behavior. Such behavior includes (1...

Diyashev, Ildar

2006-04-12T23:59:59.000Z

399

Analyzing aquifer driven reservoirs using a computer-oriented approach  

E-Print Network (OSTI)

A new computer-oriented approach for analyzing aquifer driven reservoirs incorporates both geological and historical pressure data to determine original hydrocarbons-in-place and to forecast production. This new approach does not rely entirely...

Flumerfelt, Raymond William

1996-01-01T23:59:59.000Z

400

Collection and Analysis of Reservoir Data from Testing and Operation...  

Open Energy Info (EERE)

Reservoir Data from Testing and Operation of the Raft River 5 MW Power Plant Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Proceedings: Collection...

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Seismic characterization of fractured reservoirs by focusing Gaussian beams  

E-Print Network (OSTI)

Naturally fractured reservoirs occur worldwide, and they account for the bulk of global oil production. The most important impact of fractures is their influence on fluid flow. To maximize oil production, the characterization ...

Zheng, Yingcai

402

Reducing temperature uncertainties by stochastic geothermal reservoir modelling  

Science Journals Connector (OSTI)

......Section 4) for a current geothermal district heating project in The Hague...Geothermal Reservoir A geothermal district heating project in The Hague...2008. The Den Haag Geothermal District Heating Project-3-D Models......

C. Vogt; D. Mottaghy; A. Wolf; V. Rath; R. Pechnig; C. Clauser

2010-04-01T23:59:59.000Z

403

Borehole Stability Analysis of Horizontal Drilling in Shale Gas Reservoirs  

Science Journals Connector (OSTI)

Serious wellbore instability occurs frequently during horizontal drilling in shale gas reservoirs. The conventional forecast model of in ... not suitable for wellbore stability analysis in laminated shale gas for...

Jun-Liang Yuan; Jin-Gen Deng; Qiang Tan; Bao-Hua Yu

2013-09-01T23:59:59.000Z

404

An Integrated Study Method For Exploration Of Gas Hydrate Reservoirs...  

Open Energy Info (EERE)

approach for exploration of gas hydrate reservoirs in marine areas. Authors C. Y. Sun, B. H. Niu, P. F. Wen, Y. Y. Huang, H. Y. Wang, X. W. Huang and J. Li Published Journal...

405

Fracture Evolution Following a Hydraulic Stimulation within an EGS Reservoir  

Energy.gov (U.S. Department of Energy (DOE))

DOE Geothermal Peer Review 2010 - Presentation. This project will provide the first ever formal evaluation of fracture and fracture flow evolution in an EGS reservoir following a hydraulic stimulation.

406

Exploration model for possible geothermal reservoir, Coso Hot...  

Open Energy Info (EERE)

Abstract The purpose of this study was to test the hypothesis that a steam-filled fracture geothermal reservoir exists at Coso Hot Springs KGRA, as proposed by Combs and...

407

Three-dimensional Modeling of Fracture Clusters in Geothermal Reservoirs  

Energy.gov (U.S. Department of Energy (DOE))

Project objective: to develop a 3-D numerical model for simulating mode I; II; and III (tensile; shear; and tearing propagation of multiple fractures using the virtual multi-dimensional internal bond (VMIB); to predict geothermal reservoir stimulation.

408

Seismic characterization of fractured reservoirs using 3D double beams  

E-Print Network (OSTI)

We propose an efficient target-oriented method to characterize seismic properties of fractured reservoirs: the spacing between fractures and the fracture orientation. We use both singly scattered and multiply scattered ...

Zheng, Yingcai

2012-01-01T23:59:59.000Z

409

Understanding reservoir mechanisms using phase and component streamline tracing  

E-Print Network (OSTI)

explored. The power and utility of the phase and component streamlines have been demonstrated using synthetic examples and two field cases. The new formulation of streamline tracing provides additional information about the reservoir drive mechanisms...

Kumar, Sarwesh

2009-05-15T23:59:59.000Z

410

Integrated seismic studies at the Rye Patch geothermal reservoir...  

Open Energy Info (EERE)

studies at the Rye Patch geothermal reservoir Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Integrated seismic studies at the Rye Patch...

411

Reservoir Simulation Used to Plan Diatomite Developement in Mountainous Region  

E-Print Network (OSTI)

In Santa Barbara County, Santa Maria Pacific (an exploration and production company) is expanding their cyclic steam project in a diatomite reservoir. The hilly or mountainous topography and cut and fill restrictions have interfered with the company...

Powell, Richard

2012-10-19T23:59:59.000Z

412

Hydroacoustic Estimates of Fish Density Distributions in Cougar Reservoir, 2011  

SciTech Connect

Day and night mobile hydroacoustic surveys were conducted once each month from April through December 2011 to quantify the horizontal and vertical distributions of fish throughout Cougar Reservoir, Lane County, Oregon.

Ploskey, Gene R.; Zimmerman, Shon A.; Hennen, Matthew J.; Batten, George W.; Mitchell, T. D.

2012-09-01T23:59:59.000Z

413

Geothermal reservoir engineering computer code comparison and validation  

SciTech Connect

The results of computer simulations for a set of six problems typical of geothermal reservoir engineering applications are presented. These results are compared to those obtained by others using similar geothermal reservoir simulators on the same problem set. The purpose of this code comparison is to check the performance of participating codes on a set of typical reservoir problems. The results provide a measure of the validity and appropriateness of the simulators in terms of major assumptions, governing equations, numerical accuracy, and computational procedures. A description is given of the general reservoir simulator - its major assumptions, mathematical formulation, and numerical techniques. Following the description of the model is the presentation of the results for the six problems. Included with the results for each problem is a discussion of the results; problem descriptions and result tabulations are included in appendixes. Each of the six problems specified in the contract was successfully simulated. (MHR)

Faust, C.R.; Mercer, J.W.; Miller, W.J.

1980-11-12T23:59:59.000Z

414

Chemical Depth Profiling from Neutron Reflectometry  

SciTech Connect

The material profile of a thin film can be analyzed by placing the film on a substrate and by sending a neutron beam onto it at various angles of incidence. Technically, the scattering length density of the film needs to be determined as a function of depth. A reflectometer is used to measure the amount of reflection (reflectivity) as a function of the angle of incidence. Mathematically, this is equivalent to sending the neutron beam onto the film at every energy but at a fixed angle of incidence. The film profile needs to be recovered from the measured reflectivity data. Unfortunately, the unique recovery is impossible, and many distinct unrelated profiles may correspond to the same reflectivity data. In our DOE/EPSCoR sponsored research, we have developed an analytical method to uniquely recover the profile of a thin film from the measured reflectivity data. We have shown that by taking reflectivity measurements with two different substrates, one can uniquely determine the film profile. Previously, it was known that one could uniquely recover the profile by taking reflectivity measurements with three different substrates, and our findings indicate that the same goal can be accomplished by using fewer measurements. At Mississippi State University we started an informal weekly seminar (called ''the reflectometry meeting'') at to attract various undergraduate and graduate students into the field. There were about 3 undergraduate students, 6 graduate students, and 2 faculty members attending these seminars. The PI has collaborated with Dr. Norm Berk at National Institute of Standards and Technology (NIST) on various aspects of neutron reflectometry, from which various interesting problems of theoretical and practical importance have arisen. One of these problems is closely related to the important mathematical problem known as analytic extrapolation. Under appropriate conditions (known to hold in neutron reflectometry), the reflection data taken in a finite interval of neutron energies uniquely determines the data at all energies. Even though the uniqueness is assured mathematically, there are currently no available methods for analytic extrapolation. Currently, we are working on this problem as it arises in neutron reflectometry and looking for mathematical and numerical methods to extrapolate reflection data to higher and lower neutron energies. A solution to this problem is expected to have a big impact not only in neutron reflectometry, but in many areas of physics and engineering. The PI has collaborated with Prof. Paul Sacks of Iowa State University, Prof. Daniil Sarkissian of Mississippi State University, and Prof. Levon Babadzanjanz of St. Petersburg State University, Russia on mathematical and numerical aspects of neutron reflectometry. These researchers jointly worked with the PI towards the preparation of numerical routines to extract the film profile from the reflection data. We have prepared a Mathematica interface running Fortran 95 algorithms to produce reflection data from a given profile. These Fortran 95 algorithms have been prepared by updating and modifying Prof. Sacks' Fortran 77 routine and by updating Dr. Gian Felcher's (of Argonne National Laboratory) Fortran 77 routine. We are also preparing similar algorithms written in Mathematica so that they can be used without needing Fortran. We are also working towards preparing algorithms in Fortran 95 and in Mathematica to produce the film profile from the given sets of reflectivity data.

Tuncay Aktosun

2006-03-21T23:59:59.000Z

415

MULTIDISCIPLINARY IMAGING OF ROCK PROPERTIES IN CARBONATE RESERVOIRS FOR FLOW-UNIT TARGETING  

SciTech Connect

Despite declining production rates, existing reservoirs in the US contain large quantities of remaining oil and gas that constitute a huge target for improved diagnosis and imaging of reservoir properties. The resource target is especially large in carbonate reservoirs, where conventional data and methodologies are normally insufficient to resolve critical scales of reservoir heterogeneity. The objectives of the research described in this report were to develop and test such methodologies for improved imaging, measurement, modeling, and prediction of reservoir properties in carbonate hydrocarbon reservoirs. The focus of the study is the Permian-age Fullerton Clear Fork reservoir of the Permian Basin of West Texas. This reservoir is an especially appropriate choice considering (a) the Permian Basin is the largest oil-bearing basin in the US, and (b) as a play, Clear Fork reservoirs have exhibited the lowest recovery efficiencies of all carbonate reservoirs in the Permian Basin.

Stephen C. Ruppel

2005-02-01T23:59:59.000Z

416

REAL-TIME TRACER MONITORING OF RESERVOIR STIMULATION PROCEDURES  

SciTech Connect

Ongoing Phase 2 work comprises the development and field-testing of a real-time reservoir stimulation diagnostic system. Phase 3 work commenced in June 2001, and involved conducting research, development and field-testing of real-time enhanced dual-fluid stimulation processes. Experimental field-testing to date includes three well tests. Application of these real-time stimulation processes and diagnostic technologies has been technically successful with commercial production from the ''marginal'' reservoirs in the first two well tests. The third well test proved downhole-mixing is an efficient process for acid stimulation of a carbonate reservoir that produced oil and gas with 2200 psi bottomhole reservoir pressure, however, subsequent shut-in pressure testing indicated the reservoir was characterized by low-permeability. Realtimezone continues to seek patent protection in foreign markets to the benefit of both RTZ and NETL. Realtimezone and the NETL have licensed the United States patented to Halliburton Energy Services (HES). Ongoing Phase 2 and Phase 3 field-testing continues to confirm applications of both real-time technologies, from well testing conducted over the last 12-month work period and including well test scheduled for year-end of 2002. Technical data transfer to industry is ongoing via Internet tech-transfer, public presentations and industry publications. Final Phase 3 test work will be focused on further field-testing the innovational process of blending stimulation fluids downhole. This system provides a number of advantages in comparison to older industry fracturing techniques and allows the operator to control reservoir fracture propagation and concentrations of proppant placed in the reservoir, in real-time. Another observed advantage is that lower friction pressures result, which results in lower pump treating pressures and safer reservoir hydraulic fracturing jobs.

George Scott III

2002-08-01T23:59:59.000Z

417

Heavy oil reservoirs recoverable by thermal technology. Annual report  

SciTech Connect

The purpose of this study was to compile data on reservoirs that contain heavy oil in the 8 to 25/sup 0/ API gravity range, contain at least ten million barrels of oil currently in place, and are non-carbonate in lithology. The reservoirs within these constraints were then analyzed in light of applicable recovery technology, either steam-drive or in situ combustion, and then ranked hierarchically as candidate reservoirs. The study is presented in three volumes. Volume I presents the project background and approach, the screening analysis, ranking criteria, and listing of candidate reservoirs. The economic and environmental aspects of heavy oil recovery are included in appendices to this volume. This study provides an extensive basis for heavy oil development, but should be extended to include carbonate reservoirs and tar sands. It is imperative to look at heavy oil reservoirs and projects on an individual basis; it was discovered that operators, and industrial and government analysts will lump heavy oil reservoirs as poor producers, however, it was found that upon detailed analysis, a large number, so categorized, were producing very well. A study also should be conducted on abandoned reservoirs. To utilize heavy oil, refiners will have to add various unit operations to their processes, such as hydrotreaters and hydrodesulfurizers and will require, in most cases, a lighter blending stock. A big problem in producing heavy oil is that of regulation; specifically, it was found that the regulatory constraints are so fluid and changing that one cannot settle on a favorable recovery and production plan with enough confidence in the regulatory requirements to commit capital to the project.

Kujawa, P.

1981-02-01T23:59:59.000Z

418

Performance of petroleum reservoirs containing random vertical fractures  

E-Print Network (OSTI)

PERFORMANCE OF PETROLEUM RESERVOIRS CONTAINING RANDOM VERTICAL FRACTURES A Thesis By WILLIAM LYMAN HUSKEY Approved as to style and content by: Chairxnan o Coxnxnittee ead of Departxnent PERFORMANCE OF PETROLEUM RESERVOIRS CONTAINING RANDOM...: Petroleum Engineering TABLE OF CONTENTS Page SUMMARY Z. INTRODUCTION . 3. EQUIPMENT AND PROCEDURE 4. PRESENTATION AND DISCUSSION OF RESULTS 5. CONCLUSIONS 6. ACKNOWLEDGMENTS . . 44 7. REFERENCES 8. BIBLIOGRAPHY . 47 TABLE QF GRAPHS AND FIGURES...

Huskey, William Lyman

2012-06-07T23:59:59.000Z

419

Low permeability gas reservoir production using large hydraulic fractures  

E-Print Network (OSTI)

LOVT PERMEABILITY GAS RESERVOIR PRODUCTION USING LARGE HYDRAULIC FRACTURES A Thesis by STEPHEN ALLEN HOLDITCH Approved as to style and content by: ( airman of Committee) (Head of Department) (Me er) (Member) (Membe r) (Member) (Member...) August 1970 111 ABSTRACT Low Permeability Gas Reservoir Production Using Large Hydraulic Fractures. (August 1970) Stephen Allen Holditch, B. S. , Texas ARM University Directed by: Dr, R. A. Morse There has been relatively little work published...

Holditch, Stephen A

2012-06-07T23:59:59.000Z

420

Analyzing aquifers associated with gas reservoirs using aquifer influence functions  

E-Print Network (OSTI)

ANALYZING AQUIFERS ASSOCIATED WITH GAS RESERVOIRS USING AQUIFER INFLUENCE FUNCTIONS A Thesis by GARY WAYNE TARGAC Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER... OF SCIENCE V z May 1988 z V z z I- Major Subject: Petroleum Engineering ANALYZING AQUIFERS ASSOCIATED WITH GAS RESERVOIRS USING AQUIFER INFLUENCE FUNCTIONS A Thesis by GARY WAYNE TARGAC Approved as to style and content by: (Chair of Committ R...

Targac, Gary Wayne

1988-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

The recovery of oil from carbonate reservoirs by fluid injection  

E-Print Network (OSTI)

Hole 70 Neasured and Calculated Productivities Obtained on Wells Completed Through Perforations 39 Cumulative Oil Recovery Versus Total Water and Oil Throughf low for Stratified Reservoirs- lj. O Cumulative Oil Recovery Versus Total Water and Oil... for Field A 12, Cumulative Oil Recovery Versus Total Water and Oil Throughflow for Field B 13, -20, Permeability Distribution Plots $5-52 The object of this project was to study the extent of the variations of the permeability in carbonate reservoirs...

Coleman, Dwayne Marvin

2012-06-07T23:59:59.000Z

422

The Optimization of Well Spacing in a Coalbed Methane Reservoir  

E-Print Network (OSTI)

THE OPTIMIZATION OF WELL SPACING IN A COALBED METHANE RESERVOIR A Thesis by PAHALA DOMINICUS SINURAT Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE December 2010 Major Subject: Petroleum Engineering THE OPTIMIZATION OF WELL SPACING IN A COALBED METHANE RESERVOIR A Thesis by PAHALA DOMINICUS SINURAT Submitted to the Office of Graduate Studies of Texas A...

Sinurat, Pahala Dominicus

2012-02-14T23:59:59.000Z

423

Decoherence in a single trapped ion due to engineered reservoir  

E-Print Network (OSTI)

The decoherence in trapped ion induced by coupling the ion to the engineered reservoir is studied in this paper. The engineered reservoir is simulated by random variations in the trap frequency, and the trapped ion is treated as a two-level system driven by a far off-resonant plane wave laser field. The dependence of the decoherence rate on the amplitude of the superposition state is given.

X. X. Yi; D. L. Zhou; C. P. Sun

2000-04-18T23:59:59.000Z

424

Recovery of oil from fractured reservoirs by gas displacement  

E-Print Network (OSTI)

RECOVERY OF OIL FROM FRACTURED RESERVOIRS BY GAS DISPLACEMENT A Thesis by ARILD UNNE BE RG Submitted to the Graduate College of Texas AlkM University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE August 1974... Major Subject: Petroleum Engineering RECOVERY OF OIL FROM FRACTURED RESERVOIRS BY GAS DISPLACEMENT A Thesis by ARILD UNNEBERG Approved as, to style and content by: . ( y (Chairman of Cornrnittee) (Head of Depar nt) / (Membe r) (Member) M b...

Unneberg, Arild

2012-06-07T23:59:59.000Z

425

Characterizing hydraulically fractured reservoirs using induced microearthquakes  

SciTech Connect

Hydraulic fracturing is a common method employed to increase the production of oil and gas fields. Recently, there has been increased interest in monitoring the microearthquakes induced by hydraulic fracturing as a means of obtaining data to characterize reservoir changeS induced by the injection. Two types of microearthquakes have been observed during hydraulic fracturing. Tensile events have been observed and modeled as the parting of the surfaces of a fracture. A majority of the events observed have been shear-slip events, where two sides of a fault plane slip parallel to each other but in opposite directions. The locations of the microearthquakes can be analyzed to determine regions where significant seismic energy was released, which presumably are regions where injected fluid penetrated into the rock along pre-existing fractures or zones of weakness. The spatial patterns in the locations can be analyzed to fine regions where events cluster along planes, which are interpreted to be the dominant fluid flow paths. Imaging methods can also be applied to the travel time and waveform data to obtain direct evidence for the locations of the fractures or fracture zones. 27 refs., 2 figs.

Fehler, M.

1991-01-01T23:59:59.000Z

426

Measurement of average resistance in underwater breathing apparatus  

SciTech Connect

Underwater Breathing Apparatus (UBA) have long been characterized by the mechanical work done on them during simulated breathing. For 20 years, the work of breathing has been divided by tidal volume to yield what is properly considered a volume-averaged pressure. The authors assert that when volume-averaged pressure is divided by a factor proportional to ventilation, the result is a measure of flow resistance averaged over an entire breath. This point is illustrated with both theoretical and actual pressure-volume and pressure-flow curves for a MK 16 closed-circuit UBA.

Clarke, J.R. [Navy Experimental Diving Unit, Panama City, FL (United States)

1996-09-01T23:59:59.000Z

427

Time average vibration fringe analysis using Hilbert transformation  

SciTech Connect

Quantitative phase information from a single interferogram can be obtained using the Hilbert transform (HT). We have applied the HT method for quantitative evaluation of Bessel fringes obtained in time average TV holography. The method requires only one fringe pattern for the extraction of vibration amplitude and reduces the complexity in quantifying the data experienced in the time average reference bias modulation method, which uses multiple fringe frames. The technique is demonstrated for the measurement of out-of-plane vibration amplitude on a small scale specimen using a time average microscopic TV holography system.

Kumar, Upputuri Paul; Mohan, Nandigana Krishna; Kothiyal, Mahendra Prasad

2010-10-20T23:59:59.000Z

428

Solar: annual average direct normal (DNI) map at 40km resolution for  

Open Energy Info (EERE)

map at 40km resolution for map at 40km resolution for Central America from NREL Dataset Summary Description (Abstract): A map depicting model estimates of monthly average daily total radiation using inputs derived from satellite and surface observations of cloud cover, aerosol optical depth, precipitable water vapor, albedo, atmospheric pressure and ozone sampled at a 40km resolution. (Purpose): A visual depiction of solar energy resource for concentrating solar power systems. Source NREL Date Released December 11th, 2003 (11 years ago) Date Updated October 30th, 2007 (7 years ago) Keywords Central America direct normal DNI map NREL solar SWERA UNEP Data application/pdf icon Download Map (pdf, 67.1 KiB) Quality Metrics Level of Review Some Review Comment Temporal and Spatial Coverage Frequency

429

Searching for seismic scattering off mantle interfaces between 800 km and 2000 km depth  

E-Print Network (OSTI)

, reservoirs could feed OIBs. The heat flow gener- ated by a mantle with a potassium, thorium, and uranium., 1999; Kellogg et al., 1999a]. The mid-ocean ridges would then sample the depleted reservoir, whereas

van der Hilst, Robert Dirk

430

Reservoir characterization of a Permian Giant: Yates Field, West Texas  

SciTech Connect

The Yates Field reservoir characterization project provided the geologic framework, data, and tools that support the ongoing reservoir management of Yates Field. Geologic and engineering data from 1800 wells with digital log data, 23,000 feet of quantified core analysis and description, and six decades of production data, were integrated, analyzed, and displayed in a format which could be used for field evaluation, management, and simulation. The Yates Field reservoir characterization products include: quantified, standardized, digital core descriptions for 118 cores in the field; 2-D digital cross section through every well in the field; 2-D structure and isochore maps for major and internal marker horizons, net and gross reservoir maps, net and gross shale maps, secondary calcite distribution maps, cave distribution maps, and fracture distribution maps; a 6.8 million cell 3-D geologic model of the complete reservoir that includes log, core, and production data. The reservoir characterization project resulted in a quantified description of the heterogeneous matrix and fracture network in Yates Field. It is the efficient, ongoing management of this classic dual-porosity system that has stabilized production from this sixty-eight year old, 4.2 billion barrel field.

Tinker, S.W. [Marathon Oil Co., Littleton, CO (United States); Mruk, D.H. [Marathon Oil Co., Midland, TX (United States)

1995-06-01T23:59:59.000Z

431

Application of horizontal drilling to tight gas reservoirs  

SciTech Connect

Vertical fractures and lithologic heterogeneity are extremely important factors controlling gas flow rates and total gas recovery from tight (very low permeability) reservoirs. These reservoirs generally have in situ matrix permeabilities to gas of less than 0.1 md. Enhanced gas recovery methods have usually involved hydraulic fracturing; however, the induced vertical hydraulic fractures almost always parallel the natural fracture and may not be an efficient method to establish a good conduit to the wellbore. Horizontal drilling appears to be an optimum method to cut across many open vertical fractures. Horizontal holes will provide an efficient method to drain heterogeneous tight reservoirs even in unfractured rocks. Although many horizontal wells have now been completed in coalbed methane and oil reservoirs, very few have been drilled to exclusively evaluate tight gas reservoirs. The U.S. Department of Energy (DOE) has funded some horizontal and slanthole drilling in order to demonstrate the applicability of these techniques for gas development. Four DOE holes have been drilled in Devonian gas shales in the Appalachian basin, and one hole has been drilled in Upper Cretaceous tight sandstones in the Piceance basin of Colorado. The Colorado field experiment has provided valuable information on the abundance and openness of deeply buried vertical fractures in tight sandstones. These studies, plus higher gas prices, should help encourage industry to begin to further utilize horizontal drilling as a new exploitation method for tight gas reservoirs.

Spencer, C.W. (U.S. Geological Survey, Lakewood, CO (United States)); Lorenz, J.C. (Sandia National Labs., Albuquerque, NM (United States)); Brown, C.A. (Synder Oil Co., Denver, CO (United States))

1991-03-01T23:59:59.000Z

432

IMPROVED BOUSSINESQ-TYPE EQUATIONS FOR HIGHLY-VARIABLE DEPTH  

E-Print Network (OSTI)

IMPROVED BOUSSINESQ-TYPE EQUATIONS FOR HIGHLY-VARIABLE DEPTH JUAN CARLOS MU~NOZ GRAJALES AND ANDR´E NACHBIN Abstract. Intermediate depth, Boussinesq-type modeling is used to generalize previously known are extended from the analysis of KdV-type models to include the improved Boussinesq systems in contrast

Nachbin, André

433

Depth, and Motion inVision CMSC 436/636  

E-Print Network (OSTI)

, perceived depth related #12;Head Motion Parallax Bruce and Green 90, p. 231. Kinetic Depth Effect Bruce displacement) #12;Structure from Motion Bruce and Green 90, pg. 328. #12;Image Segmentation Discontinuities Representation techniques parameters #12;Experimental Findings Control necessary for development Held

Rheingans, Penny

434

Project of Aerosol Optical Depth Change in South America  

E-Print Network (OSTI)

AerosolDepth Brazil Bolivia French Guiana Suriname Guyana Venezuela Colombia Ecuador Peru Chile Argentina Suriname Guyana Venezuela Colombia Ecuador Peru Chile Argentina Paraguay Uruguay #12;Statistics of Aerosol M ean D ec 01 to 06 Mean Month AerosolDepth Brazil Bolivia French Guiana Suriname Guyana Venezuela

Frank, Thomas D.

435

SEU sensitive depth in a submicron SRAM technology  

SciTech Connect

This work determines experimentally and by simulation the SEU sensitive depth in a 0.6 {micro}m SRAM technology. A good correlation is obtained between the two studies in the case of heavy ions deposing energy close to the critical energy. Other simulation results complete the first investigation by studying the minimum sensitive depth for ions deposing higher energies (at greater LET).

Detcheverry, C.; Bruguier, G.; Palau, J.M.; Gasiot, J. [Univ. Montpellier II (France)] [Univ. Montpellier II (France); Ecoffet, R. [CNES, Toulouse (France)] [CNES, Toulouse (France); Duzellier, S. [DERTS, Toulouse (France)] [DERTS, Toulouse (France); Barak, J.; Lifshitz, Y. [Soreq NRC, Yahvne (Israel)] [Soreq NRC, Yahvne (Israel)

1998-06-01T23:59:59.000Z

436

On depth and deep points: a calculus Ivan Mizera  

E-Print Network (OSTI)

of Tukey's median) plays a fundamental role similar to that of linear functions in the mathematical (1929) and Chamberlin (1933). For multivariate location, the proposal of Tukey (1975) was developed halfspace or Tukey's depth; for other brands of depth in multivariate location see Liu, Parelius and Singh

Mizera, Ivan

437

Quantification of uncertainty in reservoir simulations influenced by varying input geological parameters, Maria Reservoir, CaHu Field  

E-Print Network (OSTI)

to krig thickness layers, 2) morphology around well 14, 3) shelf edge orientation, 4) bathymetry ranges attributed for each facies, 5) variogram range used to simulate facies distribution, 6) extension of the erosion at top of the reservoir. The parameters...

Schepers, Karine Chrystel

2005-02-17T23:59:59.000Z

438

A depth-averaged debris-flow model that includes the effects of evolving dilatancy. II. Numerical predictions and experimental tests  

Science Journals Connector (OSTI)

...Numerical predictions and experimental tests David L. George Richard M. Iverson e-mail...software package we call D-Claw. As tests of D-Claw, we compare model output with...our numerical solution technique, and tests of numerical predictions against experimental...

2014-01-01T23:59:59.000Z

439

BULLETIN @I? THE UNITED STATES FISH COMMISSIOK. 81 The average depth of the pond should, of course, be at least 3feot, and  

E-Print Network (OSTI)

not seem to beany init now. At any rate iione hiive been taken or seen. We hare an elevation abovesea

440

A depth-averaged debris-flow model that includes the effects of evolving dilatancy. II. Numerical predictions and experimental tests  

Science Journals Connector (OSTI)

...satisfies numerical conservation by using a similarity...details). Numerical conservation of quantities transported...include a motionless pool of water lying over variable...2003 Shallow-water theory for arbitrary...1960 Systems of conservation laws. Comm. Pure...

2014-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Depositional environments and reservoir properties of the upper Queen Formation, Concho Bluff and Concho Bluff North fields, Midland basin, Texas  

SciTech Connect

The upper Queen Formation (Upper Permian) in Concho Bluff and Concho Bluff North fields (Crane, Upton, and Ector counties, Texas) consists of four thick (6-11 m) clastic members separated by evaporite members, and contains several major sandstone reservoirs. A study of cores and logs from the upper Queen was done to determine its depositional environments and the properties of its sandstone reservoirs. Four facies are present in the upper Queen. Facies 1 consists of planar- and wavy-laminated fine and very fine sandstones and silty sandstones deposited in fluvial sandflats and delta-plains. Facies 2 consists of wavy-laminated siltstones and haloturbated mudstones with anhydrite nodules deposited in subaqueous prodelta environments and subaerial saline mudflats. Facies 3 consists of well-sorted fine to very fine sandstones with horizontal and inclined planar laminae deposited in eolian sand sheets. Facies 4 consists of massive to laminated halite and anhydrite deposited in hypersaline playas. The vertical sequence of these facies indicates that the upper Queen was deposited during four cycles of fan-delta progradation into and retreat from coastal-plain playas during a sea level lowstand in the Midland basin. The sandstones of the fluvial sandflat and eolian sand-sheet facies constitute the reservoirs of the upper Queen in the fields. The average cumulative thickness of these facies is 8 m, and the fields average 16% porosity and 40-50 md of permeability. The remaining facies are all nonproductive with averagge porosities of less than 10% and average permeabilities of less than 1 md.

Mazzullo, J.; Newsom, D.; Harper, J.; McKone, C.; Price, B. (Texas A and M Univ., College Station (United States))

1992-04-01T23:59:59.000Z

442

annual average heating degree days | OpenEI  

Open Energy Info (EERE)

average heating degree days average heating degree days Dataset Summary Description (Abstract): Heating Degree Days below 18° C (degree days)The monthly accumulation of degrees when the daily mean temperature is below 18° C.NASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Nov 2007)22-year Monthly Average & Annual Sum (July 1983 - June 2005)Parameter: Heating Degree Days Below 18 degrees C (degree days)Internet: http://eosweb.larc.nasa.gov/sse/ Source U.S. National Aeronautics and Space Administration (NASA), Surface meteorology and Solar Energy (SSE) Date Released March 31st, 2009 (5 years ago) Date Updated April 01st, 2009 (5 years ago) Keywords annual average heating degree days climate GIS NASA SWERA UNEP Data application/zip icon Download Shapefile (zip, 2.7 MiB)

443

Averaging Spacetime: Where do we go from here?  

E-Print Network (OSTI)

The construction of an averaged theory of gravity based on Einstein's General Relativity is very difficult due to the non-linear nature of the gravitational field equations. This problem is further exacerbated by the difficulty in defining a mathematically precise covariant averaging procedure for tensor fields over differentiable manifolds. Together, these two ideas have been called the averaging problem for General Relativity. In the first part of the talk, an attempt to review some the various approaches to this problem will be given, highlighting strengths, weaknesses, and commonalities between them. In the second part of the talk, an argument will be made, that if one wishes to develop a well-defined averaging procedure, one may choose to parallel transport along geodesics with respect to the Levi-Cevita connection or, use the Weitzenb\\"ock connection and ensure the transportation is independent of path. The talk concludes with some open questions to generate further discussion.

R. J. van den Hoogen

2010-04-15T23:59:59.000Z

444

U.S. average gasoline price up slightly  

Annual Energy Outlook 2012 (EIA)

average retail price for regular gasoline rose slightly to 3.65 a gallon on Monday. That's up a tenth of a penny from a week ago, based on the weekly price survey by the U.S....

445

Fact #671: April 18, 2011 Average Truck Speeds  

Energy.gov (U.S. Department of Energy (DOE))

The Federal Highway Administration studies traffic volume and flow on major truck routes by tracking more than 500,000 trucks. The average speed of trucks on selected interstate highways is between...

446

Abstract Interpretation for Worst and Average Case Analysis  

E-Print Network (OSTI)

energy usage whilst bounding the average number of requests waiting to be served. PRISM is used phase extracts a control flow graph ­ for some classes of language this may already involve an abstract

Di Pierro, Alessandra

447

Weighted Coherence: A More Effective Measure Than Average Coherence  

Science Journals Connector (OSTI)

In this study, we evaluated the effectiveness of the statistic, Weighted Coherence in relation to the average or mean coherence in a particular frequency band after cross- ... using cross-spectral analysis is r...

Vikram Kumar Yeragani; Arindam Barua

2003-12-01T23:59:59.000Z

448

Table 17. Recoverable Coal Reserves and Average Recovery Percentage...  

U.S. Energy Information Administration (EIA) Indexed Site

Recoverable Coal Reserves and Average Recovery Percentage at Producing U.S. Mines by Mine Production Range and Mine Type, 2012 (million short tons) U.S. Energy Information...

449

Table A44. Average Prices of Purchased Electricity and Steam  

U.S. Energy Information Administration (EIA) Indexed Site

4. Average Prices of Purchased Electricity and Steam" 4. Average Prices of Purchased Electricity and Steam" " by Type of Supplier, Census Region, Census Division, and" " Economic Characteristics of the Establishment, 1994" " (Estimates in Dollars per Physical Units)" ," Electricity",," Steam" ," (kWh)",," (million Btu)" ,,,,,"RSE" ,"Utility","Nonutility","Utility","Nonutility","Row" "Economic Characteristics(a)","Supplier(b)","Supplier(c)","Supplier(b)","Supplier(c)","Factors"

450

Flavor Physics Data from the Heavy Flavor Averaging Group (HFAG)  

DOE Data Explorer (OSTI)

The Heavy Flavor Averaging Group (HFAG) was established at the May 2002 Flavor Physics and CP Violation Conference in Philadelphia, and continues the LEP Heavy Flavor Steering Group's tradition of providing regular updates to the world averages of heavy flavor quantities. Data are provided by six subgroups that each focus on a different set of heavy flavor measurements: B lifetimes and oscillation parameters, Semi-leptonic B decays, Rare B decays, Unitarity triangle parameters, B decays to charm final states, and Charm Physics.

451

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

South America from NREL South America from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and sky) falling on a horizontal surface. Existing ground measurement stations are used to validate the data where possible. The modeled values are accurate to approximately 10% of a true measured value within the grid cell due to the uncertainties associated with meteorological input to the model. The local cloud cover can vary significantly even within a single grid cell as a result of terrain effects and other microclimate influences. Furthermore, the uncertainty of the modeled estimates increase with distance from reliable measurement sources and with the complexity of the terrain.

452

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

Central America and the Carribean from NREL Central America and the Carribean from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and sky) falling on a horizontal surface. Existing ground measurement stations are used to validate the data where possible. The modeled values are accurate to approximately 10% of a true measured value within the grid cell due to the uncertainties associated with meteorological input to the model. The local cloud cover can vary significantly even within a single grid cell as a result of terrain effects and other microclimate influences. Furthermore, the uncertainty of the modeled estimates increase with distance from reliable measurement sources and with the complexity of the terrain.

453

U.S. Refiner Sales to End Users (Average) Prices  

U.S. Energy Information Administration (EIA) Indexed Site

Sales Type: Sales to End Users, Average Through Retail Outlets Sales for Resale, Average DTW Rack Bulk Sales Type: Sales to End Users, Average Through Retail Outlets Sales for Resale, Average DTW Rack Bulk Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Formulation/ Grade Sales Type Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History Conventional, Average 3.030 3.137 3.122 3.063 3.042 2.972 1994-2013 Conventional Regular 3.005 3.116 3.102 3.040 3.017 2.948 1994-2013 Conventional Midgrade 3.167 3.256 3.239 3.200 3.193 3.121 1994-2013 Conventional Premium 3.269 3.354 3.327 3.291 3.274 3.203 1994-2013 Oxygenated, Average - - - - - - 1994-2013 Oxygenated Regular - - - - - - 1994-2013 Oxygenated Midgrade - - - - - - 1994-2013

454

Advances on Reduced Reservoir Representation for Fast Analysis of Oil Recovery Opportunities This seminar presents recent results of a strategy that uses a reduced representation of reservoirs.  

E-Print Network (OSTI)

Advances on Reduced Reservoir Representation for Fast Analysis of Oil Recovery Opportunities of reservoirs. The strategy facilitates the task of producing recovery projections on individual or a portfolio of reservoirs, by using space reduction techniques and analytical simulations. The drive for this type

Sukop, Mike

455

Post waterflood CO{sub 2} miscible flood in light oil fluvial dominated deltaic reservoirs. Second quarterly technical progress report, [January 1, 1995--March 31, 1995  

SciTech Connect

Production from the Marg Area 1 at Port Neches is averaging 392 barrels of oil per day (BOPD) for this quarter. The production drop is due to fluctuation in both GOR and BS&W on various producing well, coupled with low water injectivity in the reservoir. We were unable to inject any tangible amount of water in the reservoir since late January. Both production and injection problems are currently being evaluated to improve reservoir performance. Well Kuhn (No. 6) was stimulated with 120 MMCF of CO{sub 2}, and was placed on production in February 1, 1995. The well was shut in for an additional month after producing dry CO{sub 2} initially. The well was opened again in early April and is currently producing about 40 BOPD. CO{sub 2} injection averaged 11.3 MMCFD including 4100 MMCFD purchased from Cardox, while water injection averaged 1000 BWPD with most of the injection occurring in the month of January.

NONE

1995-07-01T23:59:59.000Z

456

Data Integration for the Generation of High Resolution Reservoir Models  

SciTech Connect

The goal of this three-year project was to develop a theoretical basis and practical technology for the integration of geologic, production and time-lapse seismic data in a way that makes best use of the information for reservoir description and reservoir performance predictions. The methodology and practical tools for data integration that were developed in this research project have been incorporated into computational algorithms that are feasible for large scale reservoir simulation models. As the integration of production and seismic data require calibrating geological/geostatistical models to these data sets, the main computational tool is an automatic history matching algorithm. The following specific goals were accomplished during this research. (1) We developed algorithms for calibrating the location of the boundaries of geologic facies and the distribution of rock properties so that production and time-lapse seismic data are honored. (2) We developed and implemented specific procedures for conditioning reservoir models to time-lapse seismic data. (3) We developed and implemented algorithms for the characterization of measurement errors which are needed to determine the relative weights of data when conditioning reservoir models to production and time-lapse seismic data by automatic history matching. (4) We developed and implemented algorithms for the adjustment of relative permeability curves during the history matching process. (5) We developed algorithms for production optimization which accounts for geological uncertainty within the context of closed-loop reservoir management. (6) To ensure the research results will lead to practical public tools for independent oil companies, as part of the project we built a graphical user interface for the reservoir simulator and history matching software using Visual Basic.

Albert Reynolds; Dean Oliver; Gaoming Li; Yong Zhao; Chaohui Che; Kai Zhang; Yannong Dong; Chinedu Abgalaka; Mei Han

2009-01-07T23:59:59.000Z

457

The Ardross reservoir gridblock analogue: Sedimentology, statistical representivity, and flow upscaling  

SciTech Connect

We have used a reservoir gridblock-sized outcrop (10m by 100m) of fluvio-deltaic sandstones to evaluate the importance of internal heterogeneity for a hypothetical waterflood displacement process. Using a dataset based on probe permeameter measurements taken from two vertical transacts representing {open_quotes}wells{close_quotes} (5cm sampling) and one {open_quotes}core{close_quotes} sample (exhaustive 1mm-spaced sampling), we evaluate the permeability variability at different lengthscales, the correlation characteristics (structure of the variogram, function), and larger-scale trends. We then relate these statistical measures to the sedimentology. We show how the sediment architecture influences the effective tensor permeability at the lamina and bed scale, and then calculate the effective relative permeability functions for a waterflood. We compare the degree of oil recovery from the formation: (a) using averaged borehole data and no geological structure, and (b) modelling the sediment architecture of the interwell volume using mixed stochastic/deterministic methods. We find that the sediment architecture has an important effect on flow performance, mainly due to bedscale capillary trapping and a consequent reduction in the effective oil mobility. The predicted oil recovery differs by 18% when these small-scale effects are included in the model. Traditional reservoir engineering methods, using averages permeability values, only prove acceptable in high-permeability and low-heterogeneity zones. The main outstanding challenge, represented by this illustration of sub-gridblock scale heterogeneity, is how to capture the relevant geological structure along with the inherent geo-statistical variability. An approach to this problem is proposed.

Ringrose, P.; Pickup, G.; Jensen, J. [Heriot-Watt Univ., Edinburgh (United Kingdom)] [and others

1997-08-01T23:59:59.000Z

458

Geoscience/engineering characterization of the interwell environment in carbonate reservoirs based on outcrop analogs, Permian Basin, West Texas and New Mexico--waterflood performance analysis for the South Cowden Grayburg Reservoir, Ector County, Texas. Final report  

SciTech Connect

A reservoir engineering study was conducted of waterflood performance in the South Cowden field, an Upper Permian Grayburg reservoir on the Central Basin Platform in West Texas. The study was undertaken to understand the historically poor waterflood performance, evaluate three techniques for incorporating petrophysical measurements and geological interpretation into heterogeneous reservoir models, and identify issues in heterogeneity modeling and fluid-flow scaleup that require further research. The approach included analysis of relative permeability data, analysis of injection and production data, heterogeneity modeling, and waterflood simulation. The poor South Cowden waterflood recovery is due, in part, to completion of wells in only the top half of the formation. Recompletion of wells through the entire formation is estimated to improve recovery in ten years by 6 percent of the original oil in place in some areas of the field. A direct three-dimensional stochastic approach to heterogeneity modeling produced the best fit to waterflood performance and injectivity, but a more conventional model based on smooth mapping of layer-averaged properties was almost as good. The results reaffirm the importance of large-scale heterogeneities in waterflood modeling but demonstrate only a slight advantage for stochastic modeling at this scale. All the flow simulations required a reduction to the measured whole-core k{sub v}/k{sub h} to explain waterflood behavior, suggesting the presence of barriers to vertical flow not explicitly accounted for in any of the heterogeneity models. They also required modifications to the measured steady-state relative permeabilities, suggesting the importance of small-scale heterogeneities and scaleup. Vertical flow barriers, small-scale heterogeneity modeling, and relative permeability scaleup require additional research for waterflood performance prediction in reservoirs like South Cowden.

Jennings, J.W. Jr.

1997-05-01T23:59:59.000Z

459

Property:MeanReservoirTemp | Open Energy Information  

Open Energy Info (EERE)

MeanReservoirTemp MeanReservoirTemp Jump to: navigation, search Property Name MeanReservoirTemp Property Type Temperature Description Mean estimated reservoir temperature at location based on the USGS 2008 Geothermal Resource Assessment if the United States Pages using the property "MeanReservoirTemp" Showing 25 pages using this property. (previous 25) (next 25) A Abraham Hot Springs Geothermal Area + 363.15 K90 °C 194 °F 653.67 °R + Adak Geothermal Area + 428.15 K155 °C 311 °F 770.67 °R + Akun Strait Geothermal Area + 353.15 K80 °C 176 °F 635.67 °R + Akutan Fumaroles Geothermal Area + 523.15 K250 °C 482 °F 941.67 °R + Alvord Hot Springs Geothermal Area + 408.15 K135 °C 275 °F 734.67 °R + Amedee Geothermal Area + 388.15 K115 °C 239 °F 698.67 °R + Arrowhead Hot Springs Geothermal Area + 388.15 K115 °C

460

Carbonation Mechanism of Reservoir Rock by Supercritical Carbon Dioxide  

Open Energy Info (EERE)

Carbonation Mechanism of Reservoir Rock by Supercritical Carbon Dioxide Carbonation Mechanism of Reservoir Rock by Supercritical Carbon Dioxide Geothermal Lab Call Project Jump to: navigation, search Last modified on July 22, 2011. Project Title Carbonation Mechanism of Reservoir Rock by Supercritical Carbon Dioxide Project Type / Topic 1 Laboratory Call for Submission of Applications for Research, Development and Analysis of Geothermal Technologies Project Type / Topic 2 Supercritical Carbon Dioxide / Reservoir Rock Chemical Interactions Project Description Supercritical CO2 is currently becoming a more common fluid for extracting volatile oil and fragrance compounds from various raw materials that are used in perfumery. Furthermore, its use as a heat transmission fluid is very attractive because of the greater uptake capability of heat from hot reservoir rock, compared with that of water. However, one concern was the reactivity of CO2 with clay and rock minerals in aqueous and non-aqueous environments. So if this reaction leads to the formation of water-soluble carbonates, such formation could be detrimental to the integrity of wellbore infrastructure.

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Prediction of future well performance, including reservoir depletion effects  

SciTech Connect

In the past, the reservoir material balance (voidage) effects occurring between the end of the measured (known) production history and future Inflow Performance Relationship (IPR) time levels have been commonly ignored in the computation of the future IPR behavior. Neglecting the reservoir voidage that occurs during the time interval between the end of the known production history and the future IPR time levels results in erroneous estimates of the future IPR behavior. A detailed description is given of the mathematically rigorous technique that has been used in the development of a multilayer well performance simulator that properly accounts for the reservoir voidage effects. Some of the more significant results are also presented of an extensive effort to develop an accurate and computationally efficient well performance simulation model. The reservoir can be considered to be multilayered, with mixed reservoir layer completion types and outer boundary shapes, drainage areas and boundary conditions. The well performance model can be used to simulate performance in three different operating modes: (1) constant wellhead rate, (2) constant bottomhole pressure, and (3) constant wellhead pressure. The transient performance of vertical, vertically fractured and horizontal wells can be simulated with this well performance model. The well performance model uses mathematically rigorous transient solutions and not simply the approximate solutions for each of the well types, as do most of the other commercially available well performance models.

Poe, B.D. Jr.; Elbel, J.L.; Spath, J.B.; Wiggins, M.L.

1995-12-31T23:59:59.000Z

462

"2012 Average Monthly Bill- Residential"  

U.S. Energy Information Administration (EIA) Indexed Site

Residential" Residential" "(Data from forms EIA-861- schedules 4A-D, EIA-861S and EIA-861U)" "State","Number of Customers","Average Monthly Consumption (kWh)","Average Price (cents/kWh)","Average Monthly Bill (Dollar and cents)" "New England",6203726,634.13095,15.713593,99.644755 "Connecticut",1454651,730.85302,17.343298,126.75402 "Maine",703770,530.56349,14.658797,77.774225 "Massachusetts",2699141,627.15845,14.912724,93.52641 "New Hampshire",601697,614.81776,16.070168,98.802249 "Rhode Island",435448,597.34783,14.404061,86.042344 "Vermont",309019,565.03618,17.006075,96.090478 "Middle Atlantic",15727423,700.63673,15.272654,107.00582

463

"2012 Average Monthly Bill- Industrial"  

U.S. Energy Information Administration (EIA) Indexed Site

Industrial" Industrial" "(Data from forms EIA-861- schedules 4A-D, EIA-861S and EIA-861U)" "State","Number of Customers","Average Monthly Consumption (kWh)","Average Price (cents/kWh)","Average Monthly Bill (Dollar and cents)" "New England",34164,67854.037,11.83487,8030.4373 "Connecticut",4647,63947.063,12.672933,8103.9685 "Maine",2780,90741.457,7.9819499,7242.9376 "Massachusetts",21145,66710.826,12.566635,8383.3057 "New Hampshire",3444,47247.217,11.83228,5590.423 "Rhode Island",1927,39935.911,10.676724,4263.8471 "Vermont",221,536044.12,9.9796777,53495.475 "Middle Atlantic",45836,126368.14,7.4903534,9465.42 "New Jersey",12729,50817.89,10.516509,5344.2677

464

Time-average TV holography for vibration fringe analysis  

SciTech Connect

Time-average TV holography is widely used method for vibration measurement. The method generates speckle correlation time-averaged J0 fringes that can be used for full-field qualitative visualization of mode shapes at resonant frequencies of an object under harmonic excitation. In order to map the amplitudes of vibration, quantitative evaluation of the time-averaged fringe pattern is desired. A quantitative evaluation procedure based on the phase-shifting technique used in two beam interferometry has also been adopted for this application with some modification. The existing procedure requires a large number of frames to be recorded for implementation. We propose a procedure that will reduce the number of frames required for the analysis. The TV holographic system used and the experimental results obtained with it on an edge-clamped, sinusoidally excited square aluminium plate sample are discussed.

Kumar, Upputuri Paul; Kalyani, Yanam; Mohan, Nandigana Krishna; Kothiyal, Mahendra Prasad

2009-06-01T23:59:59.000Z

465

Globally Averaged Atmospheric CFC-11 Concentrations: Monthly and Annual  

NLE Websites -- All DOE Office Websites (Extended Search)

Chlorofluorocarbons » Chlorofluorocarbons » Atmospheric CFC-11 Concentrations Globally Averaged Atmospheric CFC-11 Concentrations: Monthly and Annual Data for the Period 1975-1992 DOI: 10.3334/CDIAC/atg.db1010 data Data (DB1010) Investigator M. A. K. Khalil and R. A. Rasmussen Description This data set presents globally averaged atmospheric concentrations of chlorofluorocarbon 11, known also as CFC-11 or F-11 (chemical name: trichlorofluoromethane; formula: CCl3F). The monthly global average data are derived from flask air samples collected at eight sites in six locations over the period August 1980-July 1992. The sites are Barrow (Alaska), Cape Meares (Oregon), Cape Kumukahi and Mauna Loa (Hawaii), Cape Matatula (American Samoa), Cape Grim (Tasmania), Palmer Station, and the

466

Comparison of Average Transport and Dispersion Among a Gaussian, a  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Comparison of Average Transport and Dispersion Among a Gaussian, a Comparison of Average Transport and Dispersion Among a Gaussian, a Two-Dimensional, and a Three-Dimensional Model Comparison of Average Transport and Dispersion Among a Gaussian, a Two-Dimensional, and a Three-Dimensional Model The Nuclear Regulatory Commission's (NRC's) code for predicting off-site consequences, MACCS2 (Chanin, et al. 1998) (MELCOR Accident Consequence Code System, Version 2), uses a simplified model for atmospheric transport and d ispersion (ATD), that is, a straight-line Gaussian model. The MACCS2 calculations are used by the NRC for planning purposes, for cost-benefit analyses, and in level-3 probabilistic risk analyses (PRAs). The MACCS2 ATD model has been criticized as being overly simplistic, even for its purposes. The justification for its use has been

467

Twelfth workshop on geothermal reservoir engineering: Proceedings  

SciTech Connect

Preface The Twelfth Workshop on Geothermal Reservoir Engineering was held at Stanford University on January 20-22, 1987. The year ending December 1986 was very difficult for the domestic geothermal industry. Low oil prices caused a sharp drop in geothermal steam prices. We expected to see some effect upon attendance at the Twelfth Workshop. To our surprise, the attendance was up by thirteen from previous years, with one hundred and fifty-seven registered participants. Eight foreign countries were represented: England, France, Iceland, Italy, Japan, Mexico, New Zealand, and Turkey. Despite a worldwide surplus of oil, international geothermal interest and development is growing at a remarkable pace. There were forty-one technical presentations at the Workshop. All of these are published as papers in this Proceedings volume. Seven technical papers not presented at the Workshop are also published; they concern geothermal developments and research in Iceland, Italy, and New Zealand. In addition to these forty-eight technical presentations or papers, the introductory address was given by Henry J. Ramey, Jr. from the Stanford Geothermal Program. The Workshop Banquet speaker was John R. Berg from the Department of Energy. We thank him for sharing with the Workshop participants his thoughts on the expectations of this agency in the role of alternative energy resources, specifically geothermal, within the country???s energy framework. His talk is represented as a paper in the back of this volume. The chairmen of the technical sessions made an important contribution to the workshop. Other than Stanford faculty members they included: M. Gulati, K. Goyal, G.S. Bodvarsson, A.S. Batchelor, H. Dykstra, M.J. Reed, A. Truesdell, J.S. Gudmundsson, and J.R. Counsil. The Workshop was organized by the Stanford Geothermal Program faculty, staff, and students. We would like to thank Jean Cook, Marilyn King, Amy Osugi, Terri Ramey, and Rosalee Benelli for their valued help with the meeting arrangements and preparing the Proceedings. We also owe great thanks to our students who arranged and operated the audio-visual equipment, specially Jim Lovekin. The Twelfth Workshop was supported by the Geothermal Technology Division of the U. S. Department of Energy through Contract Nos. DE-AS03-80SF11459 and DE-AS07- 84ID12529. We deeply appreciate this continued support. January 1987 Henry J. Ramey, Jr. Paul Kruger Roland N. Horne William E. Brigham Frank G. Miller Jesus Rivera

Ramey, H.J. Jr.; Kruger, P.; Miller, F.G.; Horne, R.N.; Brigham, W.E.; Rivera, J. (Stanford Geothermal Program)

1987-01-22T23:59:59.000Z

468

Thirteenth workshop on geothermal reservoir engineering: Proceedings  

SciTech Connect

PREFACE The Thirteenth Workshop on Geothermal Reservoir Engineering was held at Stanford University on January 19-21, 1988. Although 1987 continued to be difficult for the domestic geothermal industry, world-wide activities continued to expand. Two invited presentations on mature geothermal systems were a keynote of the meeting. Malcolm Grant presented a detailed review of Wairakei, New Zealand and highlighted plans for new development. G. Neri summarized experience on flow rate decline and well test analysis in Larderello, Italy. Attendance continued to be high with 128 registered participants. Eight foreign countries were represented: England, France, Iceland, Italy, New Zealand, Japan, Mexico and The Philippines. A discussion of future workshops produced a strong recommendation that the Stanford Workshop program continue for the future. There were forty-one technical presentations at the Workshop. All of these are published as papers in this Proceedings volume. Four technical papers not presented at the Workshop are also published. In addition to these forty five technical presentations or papers, the introductory address was given by Henry J. Ramey, Jr. from the Stanford Geothermal Program. The Workshop Banquet speaker was Gustavo Calderon from the Inter-American Development Bank. We thank him for sharing with the Workshop participants a description of the Bank???s operations in Costa Rica developing alternative energy resources, specifically Geothermal, to improve the country???s economic basis. His talk appears as a paper in the back of this volume. The chairmen of the technical sessions made an important contribution to the workshop. Other than Stanford faculty members they included: J. Combs, G. T. Cole, J. Counsil, A. Drenick, H. Dykstra, K. Goyal, P. Muffler, K. Pruess, and S. K. Sanyal. The Workshop was organized by the Stanford Geothermal Program faculty, staff and students. We would like to thank Marilyn King, Pat Oto, Terri Ramey, Bronwyn Jones, Yasmin Gulamani, and Rosalee Benelli for their valued help with the meeting arrangements and preparing the Proceedings. We also owe great thanks to our students who arranged and operated the audio-visual equipment, especially Jeralyn Luetkehans. The Thirteenth Workshop was supported by the Geothermal Technology Division of the U.S. Department of Energy through Contract No. DE-AS07-84ID12529. We deeply appreciate this continued support. Henry J. Ramey, Jr. Paul Kruger Roland N. Horne William E. Brigham Frank G. Miller Jean W. Cook

Ramey, H.J. Jr.; Kruger, P.; Horne, R.N.; Brigham, W.E.; Miller, F.G.; Cook, J.W. (Stanford Geothermal Program)

1988-01-21T23:59:59.000Z

469

Understanding Fault Characteristics And Sediment Depth For Geothermal  

Open Energy Info (EERE)

Understanding Fault Characteristics And Sediment Depth For Geothermal Understanding Fault Characteristics And Sediment Depth For Geothermal Exploration Using 3D Gravity Inversion In Walker Valley, Nevada Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Paper: Understanding Fault Characteristics And Sediment Depth For Geothermal Exploration Using 3D Gravity Inversion In Walker Valley, Nevada Details Activities (2) Areas (1) Regions (0) Abstract: The Southern Walker Lake Basin, situated in the Walker Lake structural domain, consists of primarily E-W directed extension along N-NNW striking normal faults. Water well drilling on the eastern slopes of the Wassuk Range, west of the city of Hawthorne, Nevada showed elevated temperatures. Two recent drill holes reaching downhole depths of more than 4000 ft give some insight to the geologic picture, but more information

470

Extended depth secondary recovery: more coal for the 80's  

SciTech Connect

There are a variety of surface mining techniques presently in use which are physically or economically unable to recover all of the coal available. A new technique known as extended depth secondary recovery is presently available in the form of the Thin Seam Miner, which is able to recover 80-85% of this otherwise lost coal, to depths of 220 feet. Extended depth secondary recovery began with the auger, which has enjoyed moderate success, despite major drawbacks. Punch mining, longwall and shortwall technologies and the push-button miner all attempted to economically remine areas, with very little success. The Thin Seam Miner, on the other hand, not only recovers 80-85% of the coal in place to depths of 220 feet, but is environmentally sound, economically feasible, safe, and adapted to mine under all the seam conditions and grades of coal found in Appalachia.

Shearer, L.K.

1982-12-01T23:59:59.000Z

471

Method and apparatus to measure the depth of skin burns  

DOE Patents (OSTI)

A new device for measuring the depth of surface tissue burns based on the rate at which the skin temperature responds to a sudden differential temperature stimulus. This technique can be performed without physical contact with the burned tissue. In one implementation, time-dependent surface temperature data is taken from subsequent frames of a video signal from an infrared-sensitive video camera. When a thermal transient is created, e.g., by turning off a heat lamp directed at the skin surface, the following time-dependent surface temperature data can be used to determine the skin burn depth. Imaging and non-imaging versions of this device can be implemented, thereby enabling laboratory-quality skin burn depth imagers for hospitals as well as hand-held skin burn depth sensors the size of a small pocket flashlight for field use and triage.

Dickey, Fred M. (Albuquerque, NM); Holswade, Scott C. (Albuquerque, NM)

2002-01-01T23:59:59.000Z

472

Understanding Fault Characteristics And Sediment Depth For Geothermal...  

Open Energy Info (EERE)

Fault Characteristics And Sediment Depth For Geothermal Exploration Using 3D Gravity Inversion In Walker Valley, Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to...

473

Depth-resolved cathodoluminescence spectroscopy of silicon supersaturated with sulfur  

E-Print Network (OSTI)

We investigate the luminescence of Si supersaturated with S (Si:S) using depth-resolved cathodoluminescence spectroscopy and secondary ion mass spectroscopy as the S concentration is varied over 2 orders of magnitude ...

Fabbri, Filippo

474

Next Generation Nuclear Plant Defense-in-Depth Approach  

SciTech Connect

The purpose of this paper is to (1) document the definition of defense-in-depth and the pproach that will be used to assure that its principles are satisfied for the NGNP project and (2) identify the specific questions proposed for preapplication discussions with the NRC. Defense-in-depth is a safety philosophy in which multiple lines of defense and conservative design and evaluation methods are applied to assure the safety of the public. The philosophy is also intended to deliver a design that is tolerant to uncertainties in knowledge of plant behavior, component reliability or operator performance that might compromise safety. This paper includes a review of the regulatory foundation for defense-in-depth, a definition of defense-in-depth that is appropriate for advanced reactor designs based on High Temperature Gas-cooled Reactor (HTGR) technology, and an explanation of how this safety philosophy is achieved in the NGNP.

Edward G. Wallace; Karl N. Fleming; Edward M. Burns

2009-12-01T23:59:59.000Z

475

Molecular Depth Profiling of Sucrose Films: A Comparative Study...  

NLE Websites -- All DOE Office Websites (Extended Search)

Cs and O Ions. Abstract: Time-of-flight secondary ion mass spectrometry (ToF-SIMS) depth profiling of sucrose thin films were investigated using 10 keV C60+, 20 keV...

476

Property:FirstWellDepth | Open Energy Information  

Open Energy Info (EERE)

FirstWellDepth FirstWellDepth Jump to: navigation, search Property Name FirstWellDepth Property Type Quantity Use this type to express a quantity of length. The default unit is the meter (m). Acceptable units (and their conversions) are: Meters - 1 m, meter, meters Meter, Meters, METER, METERS Kilometers - 0.001 km, kilometer, kilometers, Kilometer, Kilometers, KILOMETERS, KILOMETERS Miles - 0.000621371 mi, mile, miles, Mile, Miles, MILE, MILES Feet - 3.28084 ft, foot, feet, Foot, Feet, FOOT, FEET Yards - 1.09361 yd, yard, yards, Yard, Yards, YARD, YARDS Pages using the property "FirstWellDepth" Showing 5 pages using this property. B Blue Mountain Geothermal Area + 672 m0.672 km 0.418 mi 2,204.724 ft 734.906 yd + K Kilauea East Rift Geothermal Area + 1,968 m1.968 km

477

Coupled reservoir-geomechanical analysis of CO2 injection and ground deformations at In Salah, Algeria  

SciTech Connect

In Salah Gas Project in Algeria has been injecting 0.5-1 million tonnes CO{sub 2} per year over the past five years into a water-filled strata at a depth of about 1,800 to 1,900 m. Unlike most CO{sub 2} storage sites, the permeability of the storage formation is relatively low and comparatively thin with a thickness of about 20 m. To ensure adequate CO{sub 2} flow-rates across the low-permeability sand-face, the In Salah Gas Project decided to use long-reach (about 1 to 1.5 km) horizontal injection wells. In an ongoing research project we use field data and coupled reservoir-geomechanical numerical modeling to assess the effectiveness of this approach and to investigate monitoring techniques to evaluate the performance of a CO{sub 2}-injection operation in relatively low permeability formations. Among the field data used are ground surface deformations evaluated from recently acquired satellite-based inferrometry (InSAR). The InSAR data shows a surface uplift on the order of 5 mm per year above active CO{sub 2} injection wells and the uplift pattern extends several km from the injection wells. In this paper we use the observed surface uplift to constrain our coupled reservoir-geomechanical model and conduct sensitivity studies to investigate potential causes and mechanisms of the observed uplift. The results of our analysis indicates that most of the observed uplift magnitude can be explained by pressure-induced, poro-elastic expansion of the 20 m thick injection zone, but there could also be a significant contribution from pressure-induced deformations within a 100 m thick zone of shaly sands immediately above the injection zone.

Rutqvist, J.; Vasco, D.W.; Myer, L.

2009-11-01T23:59:59.000Z

478

High average power scaleable thin-disk laser  

DOE Patents (OSTI)

Using a thin disk laser gain element with an undoped cap layer enables the scaling of lasers to extremely high average output power values. Ordinarily, the power scaling of such thin disk lasers is limited by the deleterious effects of amplified spontaneous emission. By using an undoped cap layer diffusion bonded to the thin disk, the onset of amplified spontaneous emission does not occur as readily as if no cap layer is used, and much larger transverse thin disks can be effectively used as laser gain elements. This invention can be used as a high average power laser for material processing applications as well as for weapon and air defense applications.

Beach, Raymond J. (Livermore, CA); Honea, Eric C. (Sunol, CA); Bibeau, Camille (Dublin, CA); Payne, Stephen A. (Castro Valley, CA); Powell, Howard (Livermore, CA); Krupke, William F. (Pleasanton, CA); Sutton, Steven B. (Manteca, CA)

2002-01-01T23:59:59.000Z

479

Averaged equations for Josephson junction series arrays with LRC load  

E-Print Network (OSTI)

We derive the averaged equations describing a series array of Josephson junctions shunted by a parallel inductor-resistor-capacitor load. We assume that the junctions have negligable capacitance ($\\beta = 0$), and derive averaged equations which turn out to be completely tractable: in particular the stability of both in-phase and splay states depends on a single parameter, $\\del$. We find an explicit expression for $\\delta$ in terms of the load parameters and the bias current. We recover (and refine) a common claim found in the technical literature, that the in-phase state is stable for inductive loads and unstable for capacitive loads.

Kurt Wiesenfeld; James W. Swift

1994-08-26T23:59:59.000Z

480

An investigation of nonlinear xenon oscillation by method of averaging  

Science Journals Connector (OSTI)

A nonlinear analysis of xenon-temperature controlled nuclear reactor dynamics is presented. The set of equations in question belongs to a general class of rate equations with quadratic nonlinearities. Boundedness of the solutions is examined. The mean value of periodic solutions for the flux is shown to be always less than the equilibrium value. The Bogoliubov's method of averaging as extended by Case is applied to obtain approximate solutions. The mechanism of the existence of relaxation oscillations in the linear stability region is analyzed. Computer calculations are performed and found in good agreement with the approximate solutions obtained by means of the method of averaging.

Yoshiro Asahi; A.Ziya Akcasu

1973-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "reservoir average depth" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Prediction of sinkage depth of footings on soft marine sediments  

E-Print Network (OSTI)

instability on the side walls of the cavity. Footing size and sinkage depth of prototype footings are expected to have a significant effect on side- wall instability. (6) Tests in a geotechnical centrifuge are recommended as one means of studying gravity... instability on the side walls of the cavity. Footing size and sinkage depth of prototype footings are expected to have a significant effect on side- wall instability. (6) Tests in a geotechnical centrifuge are recommended as one means of studying gravity...

Yen, Shihchieh

2012-06-07T23:59:59.000Z

482

Case depth verification of hardened samples with Barkhausen noise sweeps  

SciTech Connect

An interesting topic of recent Barkhausen noise (BN) method studies is the application of the method to case depth evaluation of hardened components. The utilization of BN method for this purpose is based on the difference in the magnetic properties between the hardened case and the soft core. Thus, the detection of case depth with BN can be achieved. The measurements typically have been carried out by using low magnetizing frequencies which have deeper penetration to the ferromagnetic samples than the conventional BN measurement. However, the penetration depth is limited due to eddy current damping of the signal. We introduce here a newly found sweep measurement concept for the case depth evaluation. In this study sweep measurements were carried out with various magnetizing frequencies and magnetizing voltages to detect the effect of different frequency and voltage and their correspondence to the actual case depth values verified from destructive characterization. Also a BN measurement device that has an implemented sweep analysis option was utilised. The samples were either induction or case-hardened samples and sample geometry contained both rod samples and gear axle samples with different case depth values. Samples were also further characterized with Xray diffraction to study the residual stress state of the surface. The detailed data processing revealed that also other calculated features than the maximum slope division of the 1st derivative of the BN signal could hold the information about the case depth value of the samples. The sweep method was able to arrange the axles into correct order according to the case depth value even though the axles were used.

Santa-aho, Suvi; Vippola, Minnamari; Lepist, Toivo [Tampere University of Technology, Department of Materials Science, P.O. Box 589, 33101 Tampere (Finland); Hakanen, Merja [Stresstech Oy, Tikkutehtaantie 1, 40800 Vaajakoski (Finland); Sorsa, Aki; Leivisk, Kauko [University of Oulu, Control Engineering Laboratory, P.O. Box 4300, FIN-90014 University of Oulu (Finland)

2014-02-18T23:59:59.000Z

483

Application of Integrated Reservoir Management and Reservoir Characterization to Optimize Infill Drillings. Annual technical progress report, June 13, 1996 to June 12, 1998  

SciTech Connect

Infill drilling of wells on a uniform spacing, without regard to reservoir performance and characterization, does not optimize reservoir development because it fails to account for the complex nature of reservoir heterogeneities present in many low permeability reservoirs, and carbonate reservoirs in particular. New and emerging technologies, such as geostatistical modeling, rigorous decline curve analysis, reservoir rock typing, and special core analysis can be used to develop a 3-D simulation model for prediction of infill locations. Other technologies, such as inter-well injection tracers and magnetic flow conditioners, can also aid in the efficient evaluation and operation of both injection and producing wells. The purpose of this project was to demonstrate useful and cost effective methods of exploitation of the shallow shelf carbonate reservoirs of the Permian Basin located in West Texas.

Nevans, Jerry W.; Blasingame, Tom; Doublet, Louis; Kelkar, Mohan; Freeman, George; Callard, Jeff; Moore, David; Davies, David; Vessell, Richard; Pregger, Brian; Dixon, Bill

1999-04-27T23:59:59.000Z

484

Geothermal Exploration And Reservoir Monitoring Using Earthquakes And The  

Open Energy Info (EERE)

Geothermal Exploration And Reservoir Monitoring Using Earthquakes And The Geothermal Exploration And Reservoir Monitoring Using Earthquakes And The Passive Seismic Method Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Geothermal Exploration And Reservoir Monitoring Using Earthquakes And The Passive Seismic Method Details Activities (1) Areas (1) Regions (0) Abstract: This paper reviews the use of earthquake studies in the field of geothermal exploration. Local, regional and teleseismic events can all provide useful information about a geothermal area on various scales. It is imperative that data collection is conducted in properly designed, realistic experiments. Ground noise is still of limited usefulness as a prospecting tool. The utility of the method cannot yet be assessed because of its undeveloped methodology and the paucity of case histories.

485

The Northwest Geysers High-Temperature Reservoir- Evidence For Active  

Open Energy Info (EERE)

Geysers High-Temperature Reservoir- Evidence For Active Geysers High-Temperature Reservoir- Evidence For Active Magmatic Degassing And Implications For The Origin Of The Geysers Geothermal Field Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: The Northwest Geysers High-Temperature Reservoir- Evidence For Active Magmatic Degassing And Implications For The Origin Of The Geysers Geothermal Field Details Activities (2) Areas (1) Regions (0) Abstract: Noble gas isotope abundances in steam from the Coldwater Creek field of the Northwest Geysers, California, show mixing between a nearly pure mid-ocean ridge (MOR) type magmatic gas with high 3He/4He and low radiogenic 40*Ar (R/Ra > 8.3 and 40*Ar/4He < 0.07), and a magmatic gas diluted with crustal gas (R/Ra 0.25). The

486

Precise Gravimetry and Geothermal Reservoir Management | Open Energy  

Open Energy Info (EERE)

Precise Gravimetry and Geothermal Reservoir Management Precise Gravimetry and Geothermal Reservoir Management Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Precise Gravimetry and Geothermal Reservoir Management Abstract Modern portable gravimeters can routinely achieve a5 ugal uncertainty with careful measurementprocedures involving multiple station occupations inthe same day, and stacking of readings over at least15 minutes during each occupation. Although furtherimprovements in gravimeter accuracy are feasible,other practical factors relating to repeat surveys ofgeothermal fields make such improvements oflimited value. The two most important factors arebenchmark elevation variations (3 ugal/cm) andgroundwater level fluctuations (5-10 ugal/m). Dualfrequency GPS receivers can give elevations

487

Selecting The Optimal Logging Suite For Geothermal Reservoir Evaluation-  

Open Energy Info (EERE)

Selecting The Optimal Logging Suite For Geothermal Reservoir Evaluation- Selecting The Optimal Logging Suite For Geothermal Reservoir Evaluation- Results From The Alum 25-29 Well, Nevada Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Paper: Selecting The Optimal Logging Suite For Geothermal Reservoir Evaluation- Results From The Alum 25-29 Well, Nevada Details Activities (6) Areas (1) Regions (0) Abstract: This paper presents the results of analysis of a state of the art set of wireline petrophysical and wellbore image logs recorded in the Alum 25-29 well, southwestern Nevada. The Alum well penetrated nearly 2000 ft (610 m) of volcano-clastic rocks and more than 1000 ft of basement, separated from the sediments by a shallowly dipping detachment fault. The logs were acquired both to characterize the site and also to select the

488

DOE - Office of Legacy Management -- Pantex Sewage Reservoir - TX 03  

Office of Legacy Management (LM)

Pantex Sewage Reservoir - TX 03 Pantex Sewage Reservoir - TX 03 FUSRAP Considered Sites Site: Pantex Sewage Reservoir (TX.03 ) Designated Name: Alternate Name: