Powered by Deep Web Technologies
Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Benzene Monitor System report  

Science Conference Proceedings (OSTI)

Two systems for monitoring benzene in aqueous streams have been designed and assembled by the Savannah River Technology Center, Analytical Development Section (ADS). These systems were used at TNX to support sampling studies of the full-scale {open_quotes}SRAT/SME/PR{close_quotes} and to provide real-time measurements of benzene in Precipitate Hydrolysis Aqueous (PHA) simulant. This report describes the two ADS Benzene Monitor System (BMS) configurations, provides data on system operation, and reviews the results of scoping tests conducted at TNX. These scoping tests will allow comparison with other benzene measurement options being considered for use in the Defense Waste Processing Facility (DWPF) laboratory. A report detailing the preferred BMS configuration statistical performance during recent tests has been issued under separate title: Statistical Analyses of the At-line Benzene Monitor Study, SCS-ASG-92-066. The current BMS design, called the At-line Benzene Monitor (ALBM), allows remote measurement of benzene in PHA solutions. The authors have demonstrated the ability to calibrate and operate this system using peanut vials from a standard Hydragard{trademark} sampler. The equipment and materials used to construct the ALBM are similar to those already used in other applications by the DWPF lab. The precision of this system ({+-}0.5% Relative Standard Deviation (RSD) at 1 sigma) is better than the purge & trap-gas chromatograpy reference method currently in use. Both BMSs provide a direct measurement of the benzene that can be purged from a solution with no sample pretreatment. Each analysis requires about five minutes per sample, and the system operation requires no special skills or training. The analyzer`s computer software can be tailored to provide desired outputs. Use of this system produces no waste stream other than the samples themselves (i.e. no organic extractants).

Livingston, R.R.

1992-10-12T23:59:59.000Z

2

Integrated system design report  

DOE Green Energy (OSTI)

The primary objective of the integrated system test phase is to demonstrate the commercial potential of a coal fueled diesel engine in its actual operating environment. The integrated system in this project is defined as a coal fueled diesel locomotive. This locomotive, shown on drawing 41D715542, is described in the separate Concept Design Report. The test locomotive will be converted from an existing oil fueled diesel locomotive in three stages, until it nearly emulates the concept locomotive. Design drawings of locomotive components (diesel engine, locomotive, flatcar, etc.) are included.

Not Available

1989-07-01T23:59:59.000Z

3

Computerized Accident Incident Reporting System  

Energy.gov (U.S. Department of Energy (DOE))

The Computerized Accident/Incident Reporting System is a database used to collect and analyze DOE and DOE contractor reports of injuries, illnesses, and other accidents that occur during DOE...

4

NERSC System Reports  

NLE Websites -- All DOE Office Websites (Extended Search)

Reports Reports Usage Reports Batch Job Statistics See queue wait times, hours used, top users and other summary statistics for jobs run at NERSC (login required). Read More » Parallel Job Statistics (Cray aprun) $RestfulQuery4... Read More » Hopper Hours Used Hours used per day on Hopper. Read More » Edison Hours Used Hours used per day on Hopper. Read More » Carver Hours Used Hours used per day on Carver. Read More » Historical Data Hopper Job Size Charts This charts shows the fraction of hours used on Hopper in each of 5 job-core-size bins. 2013 2012 . 2011 . This chart shows the fraction of hours used on Hopper by jobs using greater than 16,384 cores. 2013 2012 ... Read More » Edison Job Size Charts This charts shows the fraction of hours used on Edison in each of 5

5

SPECTR System Operational Test Report  

Science Conference Proceedings (OSTI)

This report overviews installation of the Small Pressure Cycling Test Rig (SPECTR) and documents the system operational testing performed to demonstrate that it meets the requirements for operations. The system operational testing involved operation of the furnace system to the design conditions and demonstration of the test article gas supply system using a simulated test article. The furnace and test article systems were demonstrated to meet the design requirements for the Next Generation Nuclear Plant. Therefore, the system is deemed acceptable and is ready for actual test article testing.

W.H. Landman Jr.

2011-08-01T23:59:59.000Z

6

Pulsar microstructure and its quasi-periodicities with the S2 VLBI system at a resolution of 62.5 nanoseconds  

E-Print Network (OSTI)

We report on a study of microstructure and its quasi-periodicities of three pulsars at 1.65 GHz with the S2 VLBI system at a resolution of 62.5 ns, by far the highest for any such statistical study yet. For PSR B1929+10 we found in the average cross-correlation function (CCF) broad microstructure with a characteristic timescale of 95+-10 mcs and confirmed microstructure with characteristic timescales between 100 and 450 mcs for PSRs B0950+08 and B1133+16. On a finer scale PSRs B0950+08, B1133+16 (component II) and B1929+10 show narrow microstructure with a characteristic timescale in the CCFs of ~10 mcs, the shortest found in the average CCF or autocorrelation function (ACF) for any pulsar, apart perhaps for the Crab pulsar. Histograms of microstructure widths are skewed heavily toward shorter timescales but display a sharp cutoff. The shortest micropulses have widths between 2 and 7 mcs. No nanopulses or unresolved pulse spikes were detected. Cross-power spectra of single pulses show a large range of complexity with single spectral features representing classic quasi-periodicities and broad and overlapping features with essentially no periodicities at all. Significant differences were found for the two components of PSR B1133+16 in every aspect of our statistical analysis of micropulses and their quasi-periodicities. Asymmetries in the magnetosphere and the hollow cone of emission above the polar cap of the neutron star may be responsible for these differences.

M. V. Popov; N. Bartel; W. H. Cannon; A. Yu. Novikov; V. I. Kondratiev; V. I. Altunin

2001-07-04T23:59:59.000Z

7

The NSTX Trouble Reporting System  

Science Conference Proceedings (OSTI)

An online Trouble Reporting System (TRS) has been introduced at the National Spherical Torus Experiment (NSTX). The TRS is used by NSTX operators to report problems that affect NSTX operations. The purpose of the TRS is to enhance NSTX reliability and maintainability by identifying components, occurrences, and trends that contribute to machine downtime. All NSTX personnel have access to the TRS. The user interface is via a web browser, such as Netscape or Internet Explorer. This web-based feature permits any X-terminal, PC, or MAC access to the TRS. The TRS is based upon a trouble reporting system developed at the DIII-D Tokamak, at General Atomics Technologies. This paper will provide a detailed description of the TRS software architecture, user interface, MS SQL server interface and operational experiences. In addition, sample data from the TRS database will be summarized and presented.

S. Sengupta; G. Oliaro

2002-01-28T23:59:59.000Z

8

Pollution Prevention Tracking and Reporting System  

Energy.gov (U.S. Department of Energy (DOE))

Welcome to the Department of Energy's Pollution Prevention Tracking and Reporting System (PPTRS). DOE uses this system to collect information about, and assess the performance of, the Department's...

9

Noncompliance Tracking System Registration and Reporting  

NLE Websites -- All DOE Office Websites (Extended Search)

Noncompliance Tracking System Registration and Reporting Office of Enforcement and Oversight NTS Reporting NTS Registration (For new registration and password changes) REGISTRATION INFORMATION Registrants for the Noncompliance Tracking System (NTS) with an ACTIVE ACCOUNT for the HSS Reporting Systems: Occurrence Reports & Processing System (ORPS), Computerized Accident/Incident Reporting System (CAIRS), Suspect Counterfeit Items (SCI), or the Daily Occurrence (DO) reports can use the same credentials to access NTS. Please access NTS REPORTING. Registrants who DO NOT have an HSS Reporting Systems account, or who have not accessed their account within the past six months MUST REGISTER for a NTS account. Please register at: HSS Reporting Systems Registration. If you need additional information or assistance in registering, please contact HSS User Support.

10

Smart Grid System Report | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Smart Grid System Report Smart Grid System Report This annex presents papers covering each of the 20 metrics identified in Section 2.1. These metric papers were prepared in advance...

11

Occurrence Reporting and Processing System  

NLE Websites -- All DOE Office Websites (Extended Search)

for generic implications and operational improvements. The Occurrence Reporting Program directives are DOE Order 232.2, Occurrence Reporting and Processing of Operations...

12

Smart Grid System Report | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

System Report System Report Smart Grid System Report This annex presents papers covering each of the 20 metrics identified in Section 2.1. These metric papers were prepared in advance of the main body of the report and collectively form its informational backbone. The list of metrics is derived from the material developed at the Smart Grid Implementation Workshop. The objective of the metric development process was to distill the best ideas into a small number of metrics with a reasonable chance of measurement and assessment. Smart Grid System Report More Documents & Publications 2009 Smart Grid System Report (July 2009) 2010 Smart Grid System Report (February 2012) Statement of Patricia Hoffman, Acting Assistant Secretary for Electricity Delivery and Energy Reliability, U.S. Department of Energy Before the

13

The ATP's Business Reporting System  

Science Conference Proceedings (OSTI)

... participants are reporting significant acceleration of R&D, stimulation of beneficial ... business and economic merit of proposals as well as scientific ...

2011-10-19T23:59:59.000Z

14

Building America Systems Integration Research Annual Report:...  

NLE Websites -- All DOE Office Websites (Extended Search)

Systems Integration Research Annual Report: FY 2012 Prepared for: Building America Building Technologies Program Office of Energy Efficiency and Renewable Energy U.S....

15

Preoperational test report, primary ventilation system  

SciTech Connect

This represents a preoperational test report for Primary Ventilation Systems, Project W-030. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. The system provides vapor space filtered venting of tanks AY101, AY102, AZ101, AZ102. The tests verify correct system operation and correct indications displayed by the central Monitor and Control System.

Clifton, F.T.

1997-11-04T23:59:59.000Z

16

Preoperational test report, vent building ventilation system  

Science Conference Proceedings (OSTI)

This represents a preoperational test report for Vent Building Ventilation Systems, Project W-030. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. The system provides Heating, Ventilation, and Air Conditioning (HVAC) for the W-030 Ventilation Building. The tests verify correct system operation and correct indications displayed by the central Monitor and Control System.

Clifton, F.T.

1997-11-04T23:59:59.000Z

17

Electromagnetic exploration system. Progress report  

DOE Green Energy (OSTI)

A design for a cost effective, highly flexible, and portable controlled source EM exploration system is presented. The design goals of the CMOS micro-processor based receiver and its companion transmitter are listed. (MHR)

Not Available

1978-11-01T23:59:59.000Z

18

Computerized Accident/Incident Reporting System  

NLE Websites -- All DOE Office Websites (Extended Search)

Accident Recordkeeping and Reporting Accident Recordkeeping and Reporting Accident/Incident Recordkeeping and Reporting CAIRS logo Computerized Accident Incident Reporting System CAIRS Database The Computerized Accident/Incident Reporting System is a database used to collect and analyze DOE and DOE contractor reports of injuries, illnesses, and other accidents that occur during DOE operations. Injury and Illness Dashboard The Dashboard provides an alternate interface to CAIRS information. The initial release of the Dashboard allows analysis of composite DOE-wide information and summary information by Program Office, and site. Additional data feature are under development. CAIRS Registration Form CAIRS is a Government computer system and, as such, has security requirements that must be followed. Access to the

19

Army Energy and Water Reporting System Assessment  

SciTech Connect

There are many areas of desired improvement for the Army Energy and Water Reporting System. The purpose of system is to serve as a data repository for collecting information from energy managers, which is then compiled into an annual energy report. This document summarizes reported shortcomings of the system and provides several alternative approaches for improving application usability and adding functionality. The U.S. Army has been using Army Energy and Water Reporting System (AEWRS) for many years to collect and compile energy data from installations for facilitating compliance with Federal and Department of Defense energy management program reporting requirements. In this analysis, staff from Pacific Northwest National Laboratory found that substantial opportunities exist to expand AEWRS functions to better assist the Army to effectively manage energy programs. Army leadership must decide if it wants to invest in expanding AEWRS capabilities as a web-based, enterprise-wide tool for improving the Army Energy and Water Management Program or simply maintaining a bottom-up reporting tool. This report looks at both improving system functionality from an operational perspective and increasing user-friendliness, but also as a tool for potential improvements to increase program effectiveness. The authors of this report recommend focusing on making the system easier for energy managers to input accurate data as the top priority for improving AEWRS. The next major focus of improvement would be improved reporting. The AEWRS user interface is dated and not user friendly, and a new system is recommended. While there are relatively minor improvements that could be made to the existing system to make it easier to use, significant improvements will be achieved with a user-friendly interface, new architecture, and a design that permits scalability and reliability. An expanded data set would naturally have need of additional requirements gathering and a focus on integrating with other existing data sources, thus minimizing manually entered data.

Deprez, Peggy C.; Giardinelli, Michael J.; Burke, John S.; Connell, Linda M.

2011-09-01T23:59:59.000Z

20

ISDSN Sensor System Phase One Test Report  

Science Conference Proceedings (OSTI)

This Phase 1 Test Report documents the test activities and results completed for the Idaho National Laboratory (INL) sensor systems that will be deployed in the meso-scale test bed (MSTB) at Florida International University (FIU), as outlined in the ISDSN-MSTB Test Plan. This report captures the sensor system configuration tested; test parameters, testing procedure, any noted changes from the implementation plan, acquired test data sets, and processed results.

Gail Heath

2011-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Power Systems Development Facility progress report  

Science Conference Proceedings (OSTI)

This is a report on the progress in design and construction of the Power Systems Development Facility. The topics of the report include background information, descriptions of the advanced gasifier, advanced PFBC, particulate control devices, and fuel cell. The major activities during the past year have been the final stages of design, procurement of major equipment and bulk items, construction of the facility, and the preparation for the operation of the Facility in late 1995.

Rush, R.E.; Hendrix, H.L.; Moore, D.L.; Pinkston, T.E.; Vimalchand, P.; Wheeldon, J.M.

1995-11-01T23:59:59.000Z

22

Analysis of Hybrid Hydrogen Systems: Final Report  

DOE Green Energy (OSTI)

Report on biomass pathways for hydrogen production and how they can be hybridized to support renewable electricity generation. Two hybrid systems were studied in detail for process feasibility and economic performance. The best-performing system was estimated to produce hydrogen at costs ($1.67/kg) within Department of Energy targets ($2.10/kg) for central biomass-derived hydrogen production while also providing value-added energy services to the electric grid.

Dean, J.; Braun, R.; Munoz, D.; Penev, M.; Kinchin, C.

2010-01-01T23:59:59.000Z

23

Audit Report, Evaluation of Classified Information Systems Security...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Report, Evaluation of Classified Information Systems Security Program, DOEIG-0518 Audit Report, Evaluation of Classified Information Systems Security Program, DOEIG-0518 All...

24

Test report : Princeton power systems prototype energy storage system.  

SciTech Connect

The Department of Energy Office of Electricity (DOE/OE), Sandia National Laboratory (SNL) and the Base Camp Integration Lab (BCIL) partnered together to incorporate an energy storage system into a microgrid configured Forward Operating Base to reduce the fossil fuel consumption and to ultimately save lives. Energy storage vendors will be sending their systems to SNL Energy Storage Test Pad (ESTP) for functional testing and then to the BCIL for performance evaluation. The technologies that will be tested are electro-chemical energy storage systems comprised of lead acid, lithium-ion or zinc-bromide. Princeton Power Systems has developed an energy storage system that utilizes lithium ion phosphate batteries to save fuel on a military microgrid. This report contains the testing results and some limited analysis of performance of the Princeton Power Systems Prototype Energy Storage System.

Rose, David Martin; Schenkman, Benjamin L.; Borneo, Daniel R.

2013-08-01T23:59:59.000Z

25

Railcar waste transfer system hydrostatic test report  

SciTech Connect

This Acceptance Test Report (ATR) documents for record purposes the field results, acceptance, and approvals of the completed acceptance test per HNF-SD-W417-ATP-001, ''Rail car Waste Transfer System Hydrostatic Test''. The test was completed and approved without any problems or exceptions.

Ellingson, S.D.

1997-04-03T23:59:59.000Z

26

Acceptance test report: Backup power system  

SciTech Connect

Acceptance Test Report for construction functional testing of Project W-030 Backup Power System. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. Backup power includes a single 125 KW diesel generator, three 10-kva uninterruptible power supply units, and all necessary control.

Cole, D.B. [Westinghouse Hanford Co., Richland, WA (United States)

1996-01-26T23:59:59.000Z

27

Vitrification Facility integrated system performance testing report  

Science Conference Proceedings (OSTI)

This report provides a summary of component and system performance testing associated with the Vitrification Facility (VF) following construction turnover. The VF at the West Valley Demonstration Project (WVDP) was designed to convert stored radioactive waste into a stable glass form for eventual disposal in a federal repository. Following an initial Functional and Checkout Testing of Systems (FACTS) Program and subsequent conversion of test stand equipment into the final VF, a testing program was executed to demonstrate successful performance of the components, subsystems, and systems that make up the vitrification process. Systems were started up and brought on line as construction was completed, until integrated system operation could be demonstrated to produce borosilicate glass using nonradioactive waste simulant. Integrated system testing and operation culminated with a successful Operational Readiness Review (ORR) and Department of Energy (DOE) approval to initiate vitrification of high-level waste (HLW) on June 19, 1996. Performance and integrated operational test runs conducted during the test program provided a means for critical examination, observation, and evaluation of the vitrification system. Test data taken for each Test Instruction Procedure (TIP) was used to evaluate component performance against system design and acceptance criteria, while test observations were used to correct, modify, or improve system operation. This process was critical in establishing operating conditions for the entire vitrification process.

Elliott, D.

1997-05-01T23:59:59.000Z

28

Large hydrofoil transmission system study. Final report  

SciTech Connect

This report presents the results of a study to determine the performance and physical characteristics of an ac electrical system intended for use as the propulsion system of large hydrofoils. Section I provides a technical description of the system in terms of performance, weight and component characteristics. Section II describes anticipated problems associated with development of the system and its components, and includes activities through design and fabrication, and qualification of an integrated system. Two system configurations are considereed in this study. Configuration I which is the preferred one, consists of two direct-turbine-driven ac generators supplying electrical power to either foilborne or hullborne propeller induction drive motors. Conventional switchgear is used for connecting the generator to either the foil or hull drive motors. Each induction motor supplies power to a fixed pitch propeller via a planetary type gearbox. Speed and power output of each induction motor is controlled by fuel to the turbine. Configuration II consists of independent foilborne and hullborne propulsion systems. For takeoff and foilborne operation, two direct LM2500 turbine-drive ac generators supply electrical power to the foil propeller induction motors. Operation in this mode is identical to Configuration I. Configuration II provides a trade off between greater system weight, against a lower hullborne fuel consumption rate obtained by operating smaller turbines in hullborne mode. This provides, potentially, a greater hullborne range.

1977-10-11T23:59:59.000Z

29

Tehachapi solar thermal system first annual report  

DOE Green Energy (OSTI)

The staff of the Southwest Technology Development Institute (SWTDI), in conjunction with the staff of Industrial Solar Technology (IST), have analyzed the performance, operation, and maintenance of a large solar process heat system in use at the 5,000 inmate California Correctional Institution (CCI) in Tehachapi, CA. This report summarizes the key design features of the solar plant, its construction and maintenance histories through the end of 1991, and the performance data collected at the plant by a dedicated on-site data acquisition system (DAS).

Rosenthal, A. [Southwest Technology Development Inst., Las Cruces, NM (US)

1993-05-01T23:59:59.000Z

30

Noncompliance Tracking System Registration and Reporting | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Noncompliance Tracking System Registration and Reporting Noncompliance Tracking System Registration and Reporting Noncompliance Tracking System Registration and Reporting NTS Reporting NTS Registration (For new registration) REGISTRATION INFORMATION Once NTS account access has been granted, registrants for the Noncompliance Tracking System (NTS) with an ACTIVE ACCOUNT for the HSS Reporting Systems: Occurrence Reports & Processing System (ORPS), Computerized Accident/Incident Reporting System (CAIRS), Suspect Counterfeit Items (SCI), or the Daily Occurrence (DO) reports can use the same credentials to access NTS. Please access NTS REPORTING. Registrants who DO NOT have an HSS Reporting Systems account, or who have not accessed their account within the past six months MUST REGISTER for a NTS account. Please register at: HSS Reporting Systems Registration.

31

Hydrogen energy systems studies. Final technical report  

SciTech Connect

The results of previous studies suggest that the use of hydrogen from natural gas might be an important first step toward a hydrogen economy based on renewables. Because of infrastructure considerations (the difficulty and cost of storing, transmitting and distributing hydrogen), hydrogen produced from natural gas at the end-user`s site could be a key feature in the early development of hydrogen energy systems. In the first chapter of this report, the authors assess the technical and economic prospects for small scale technologies for producing hydrogen from natural gas (steam reformers, autothermal reformers and partial oxidation systems), addressing the following questions: (1) What are the performance, cost and emissions of small scale steam reformer technology now on the market? How does this compare to partial oxidation and autothermal systems? (2) How do the performance and cost of reformer technologies depend on scale? What critical technologies limit cost and performance of small scale hydrogen production systems? What are the prospects for potential cost reductions and performance improvements as these technologies advance? (3) How would reductions in the reformer capital cost impact the delivered cost of hydrogen transportation fuel? In the second chapter of this report the authors estimate the potential demand for hydrogen transportation fuel in Southern California.

Ogden, J.M.; Kreutz, T.; Kartha, S.; Iwan, L.

1996-08-13T23:59:59.000Z

32

Environmental Systems Research FY-99 Annual Report  

SciTech Connect

The Environmental Systems Research (ESR) Program, a part of the Environmental Systems Research and Analysis (ESRA) Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Department of Energy's Office of Environmental Management (EM). The original portfolio of research activities was assembled after an analysis of the EM technology development and science needs as gathered by the Site Technology Coordination Groups (STCGs) complex-wide. Current EM investments in science and technology throughout the research community were also included in this analysis to avoid duplication of efforts. This is a progress report for the second year of the ESR Program (Fiscal Year 99). A report of activities is presented for the five ESR research investment areas: (a) Transport Aspects of Selective Mass Transport Agents, (b) Chemistry of Environmental Surfaces, (c) Materials Dynamics, (d) Characterization Science, and (e) Computational Simulation of Mechanical and Chemical Systems. In addition to the five technical areas, activities in the Science and Technology Foundations element of the program, e.g., interfaces between ESR and the EM Science Program (EMSP) and the EM Focus Areas, are described.

Miller, D.L.

2000-01-01T23:59:59.000Z

33

Environmental Systems Research, FY-99 Annual Report  

Science Conference Proceedings (OSTI)

The Environmental Systems Research (ESR) Program, a part of the Environmental Systems Research and Analysis (ESRA) Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Department of Energy's Office of Environmental Management (EM). The original portfolio of research activities was assembled after an analysis of the EM technology development and science needs as gathered by the Site Technology Coordination Groups (STCGs) complex-wide. Current EM investments in science and technology throughout the research community were also included in this analysis to avoid duplication of efforts. This is a progress report for the second year of the ESR Program (Fiscal Year 99). A report of activities is presented for the five ESR research investment areas: (a) Transport Aspects of Selective Mass Transport Agents, (b) Chemistry of Environmental Surfaces, (c) Materials Dynamics, (d) Characterization Science, and (e) Computational Simulation of Mechanical and Chemical Systems. In addition to the five technical areas, activities in the Science and Technology Foundations element of the program, e.g., interfaces between ESR and the EM Science Program (EMSP) and the EM Focus Areas, are described.

Miller, David Lynn

2000-01-01T23:59:59.000Z

34

National Geoscience Data Repository System. Final report  

SciTech Connect

The American Geological Institute (AGI) has completed the first phase of a study to assess the feasibility of establishing a National Geoscience Data Repository System to capture and preserve valuable geoscientific data. The study was initiated in response to the fact that billions of dollars worth of domestic geological and geophysical data are in jeopardy of being irrevocably lost or destroyed as a consequence of the ongoing downsizing of the US energy and minerals industry. This report focuses on two major issues. First, it documents the types and quantity of data available for contribution to a National Geoscience Data Repository System. Second, it documents the data needs and priorities of potential users of the system. A National Geoscience Data Repository System would serve as an important and valuable source of information for the entire geoscience community for a variety of applications, including environmental protection, water resource management, global change studies, and basic and applied research. The repository system would also contain critical data that would enable domestic energy and minerals companies to expand their exploration and production programs in the United States for improved recovery of domestic oil, gas, and mineral resources.

Schiffries, C.M.; Milling, M.E.

1994-03-01T23:59:59.000Z

35

2010 Smart Grid System Report (February 2012) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Smart Grid System Report (February 2012) Smart Grid System Report (February 2012) 2010 Smart Grid System Report (February 2012) Section 1302 of Title XIII of the Energy Independence and Security Act of 2007 directs the Secretary of Energy to "...report to Congress concerning the status of smart grid deployments nationwide and any regulatory or government barriers to continued deployment." This document satisfies this directive and represents the second installment of this report to Congress, which is to be updated biennially. 2010 Smart Grid System Report 2010 Smart Grid System Report Appendix A 2010 Smart Grid System Report Appendix B More Documents & Publications 2009 Smart Grid System Report (July 2009) Smart Grid System Report Statement of Patricia Hoffman, Acting Assistant Secretary for Electricity

36

Building integrated photovoltaic systems analysis: Preliminary report  

SciTech Connect

The National Renewable Energy Laboratory (NREL) has estimated that the deployment of photovoltaics (PV) in the commercial buildings sector has the potential to contribute as much as 40 gigawatts peak electrical generation capacity and displace up to 1.1 quads of primary fuel use. A significant portion of this potential exists for smaller buildings under 25,000 square feet (2,300 square meters) in size or two stories or less, providing a strong cross over potential for residential applications as well. To begin to achieve this potential, research is needed to define the appropriate match of PV systems to energy end-uses in the commercial building sector. This report presents preliminary findings for a technical assessment of several alternative paths to integrate PV with building energy systems.

Not Available

1993-08-01T23:59:59.000Z

37

DCE Bio Detection System Final Report  

SciTech Connect

The DCE (DNA Capture Element) Bio-Detection System (Biohound) was conceived, designed, built and tested by PNNL under a MIPR for the US Air Force under the technical direction of Dr. Johnathan Kiel and his team at Brooks City Base in San Antonio Texas. The project was directed toward building a measurement device to take advantage of a unique aptamer based assay developed by the Air Force for detecting biological agents. The assay uses narrow band quantum dots fluorophores, high efficiency fluorescence quenchers, magnetic micro-beads beads and selected aptamers to perform high specificity, high sensitivity detection of targeted biological materials in minutes. This final report summarizes and documents the final configuration of the system delivered to the Air Force in December 2008

Lind, Michael A.; Batishko, Charles R.; Morgen, Gerald P.; Owsley, Stanley L.; Dunham, Glen C.; Warner, Marvin G.; Willett, Jesse A.

2007-12-01T23:59:59.000Z

38

Hydrogen, CNG, and HHCNG Dispenser System - Prototye Report  

NLE Websites -- All DOE Office Websites (Extended Search)

FreedomCAR & Vehicle Technologies Program Advanced Vehicle Testing Activity Hydrogen, CNG, and HCNG Dispenser System - Prototype Report TECHNICAL REPORT Don Karner Scott...

39

EIA - The National Energy Modeling System: An Overview 2003-Report...  

Annual Energy Outlook 2012 (EIA)

Report Chapters The National Energy Modeling System: An Overview 2003 Report Chapters pdf image Preface pdf image Introduction pdf image Overview of NEMS pdf image Carbon Dioxide...

40

Potassium emission absorption system. Topical report 12  

DOE Green Energy (OSTI)

The Potassium Emission Absorption System is one of the advanced optical diagnostics developed at Mississippi State University to provide support for the demonstration of prototype-scale coal-fired combustion magnetohydrodynamic (MHD) electrical power generation. Intended for application in the upstream of an MHD flow, the system directly measures gas temperature and neutral potassium atom number density through spectroscopic emission absorption techniques. From these measurements the electron density can be inferred from a statistical equilibrium calculation and the electron conductivity in the MHD channel found by use of an electron mobility model. The instrument has been utilized for field test measurements on MHD facilities for almost a decade and has been proven to provide useful measurements as designed for MHD nozzle, channel, and diffuser test sections. The theory of the measurements, a system description, its capabilities, and field test measurement results are reported here. During the development and application of the instrument several technical issues arose which when addressed advanced the state of the art in emission absorption measurement. Studies of these issues are also reported here and include: two-wavelength measurements for particle-laden flows, potassium D-line far wing absorption coefficient, bias in emission absorption measurements arising from dirty windows and misalignments, non-coincident multiwavelength emission absorption sampling errors, and lineshape fitting for boundary layer flow profile information. Although developed for NLHD application, the instrument could be applied to any high temperature flow with a resonance line in the 300 to 800 nm range, for instance other types of flames, rocket plumes or low temperature plasmas.

Bauman, L.E.

1995-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Washington Closure Hanford System Engineer Program FY2010 Annual Report  

SciTech Connect

This report is a summary of the assessments of the vital safety systems (VSS) that are administered under WCHs system engineer program.

J.N. Winters

2010-11-02T23:59:59.000Z

42

Pentek metal coating removal system: Baseline report  

SciTech Connect

The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

1997-07-31T23:59:59.000Z

43

Occurrence Reporting and Processing System | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Occurrence Reporting and Processing System Occurrence Reporting and Processing System Occurrence Reporting and Processing System The Department of Energy's Occurrence Reporting Program provides timely notification to the DOE complex of events that could adversely affect: public or DOE worker health and safety, the environment, national security, DOE's safeguards and security interests, functioning of DOE facilities, or the Department's reputation. DOE analyzes aggregate occurrence information for generic implications and operational improvements. The Occurrence Reporting Program directives are DOE Order 232.2, Occurrence Reporting and Processing of Operations Information, and DOE Standard DOE-STD-1197-2011, Occurrence Reporting Causal Analysis. Contact Ashley Ruocco for information and assistance on

44

Petroleum supply monthly, with data from June 1996  

Science Conference Proceedings (OSTI)

The Petroleum Supply Division (PSD) of the Energy Information Administration (EIA) collects and published information on petroleum supply and disposition in the United States. The information is collected through a series of surveys that make up the Petroleum Supply Reporting System (PSRS). The PSRS data are published in the Weekly Petroleum Status Report (WPSR), Petroleum Supply Monthly (PSM), and Petroleum Supply Annual (PSA). This report presents information on crude oil production, crude oil imports and exports, refinery operations, natural gas processing, transportation, and oxygenate data.

NONE

1996-08-01T23:59:59.000Z

45

Federal Energy Management Program: EISA Compliance Tracking System Reports  

NLE Websites -- All DOE Office Websites (Extended Search)

EISA Compliance EISA Compliance Tracking System Reports and Data to someone by E-mail Share Federal Energy Management Program: EISA Compliance Tracking System Reports and Data on Facebook Tweet about Federal Energy Management Program: EISA Compliance Tracking System Reports and Data on Twitter Bookmark Federal Energy Management Program: EISA Compliance Tracking System Reports and Data on Google Bookmark Federal Energy Management Program: EISA Compliance Tracking System Reports and Data on Delicious Rank Federal Energy Management Program: EISA Compliance Tracking System Reports and Data on Digg Find More places to share Federal Energy Management Program: EISA Compliance Tracking System Reports and Data on AddThis.com... Requirements by Subject Requirements by Regulation Notices & Rules

46

Ocean energy conversion systems annual research report  

DOE Green Energy (OSTI)

Alternative power cycle concepts to the closed-cycle Rankine are evaluated and those that show potential for delivering power in a cost-effective and environmentally acceptable fashion are explored. Concepts are classified according to the ocean energy resource: thermal, waves, currents, and salinity gradient. Research projects have been funded and reported in each of these areas. The lift of seawater entrained in a vertical steam flow can provide potential energy for a conventional hydraulic turbine conversion system. Quantification of the process and assessment of potential costs must be completed to support concept evaluation. Exploratory development is being completed in thermoelectricity and 2-phase nozzles for other thermal concepts. Wave energy concepts are being evaluated by analysis and model testing with present emphasis on pneumatic turbines and wave focussing. Likewise, several conversion approaches to ocean current energy are being evaluated. The use of salinity resources requires further research in membranes or the development of membraneless processes. Using the thermal resource in a Claude cycle process as a power converter is promising, and a program of R and D and subsystem development has been initiated to provide confirmation of the preliminary conclusion.

Not Available

1981-03-01T23:59:59.000Z

47

Center for Power Electronics Systems PROGRESS REPORT  

E-Print Network (OSTI)

PROGRESS REPORT 2010 SMES program S uperconducting magnetic energy storage (SMES) is a way of storing TECHNOLOGIES Standard-Cell Passive IPEMs Motor and Converter Integration Control and Sensor Integration Thermal;CPES 10 YEAR PROGRESS REPORT 2010 CPES 10 YEAR PROGRESS REPORT Chapter 1: Introduction Outlines

Beex, A. A. "Louis"

48

Status Report, Essential System Functionality - January 2006 | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Status Report, Essential System Functionality - January 2006 Status Report, Essential System Functionality - January 2006 Status Report, Essential System Functionality - January 2006 Report on Essential System Functionality In 2004 and 2005, the Office of Independent Oversight, within the Office of Security and Safety Performance Assurance, performed ten evaluations of essential system functionality (ESF). These ESF reviews are highly technical, detailed engineering evaluations of selected essential systems within one or more facilities at each site. This report summarizes the observations and insights from these reviews. Although most essential safety systems that were reviewed were well maintained, tested, and operated, there were significant weaknesses in some aspects of engineering design and analysis that, for some safety systems,

49

System integration of marketable subsystems (second collection of progress reports)  

DOE Green Energy (OSTI)

These monthly reports, covering the period from February 1978 through June 1978, reflect the progress in five major areas: systems integration of marketable subsystems; development, design, and building of site data acquisition subsystems; development and operation of the central data processing system; operation of the MSFC solar test facility; and systems analysis. Some of these reports are in presentation form (charts)

Not Available

1978-07-01T23:59:59.000Z

50

Prototype solar heating and cooling systems. Monthly progress reports  

DOE Green Energy (OSTI)

This report is a collection of monthly status reports from the AiResearch Manufacturing Company, who is developing eight prototype solar heating and cooling systems under NASA Contract NAS8-32091. This effort calls for the development, manufacture, test, system installation, maintenance, problem resolution, and performance evaluation. The systems are 3-, 25-, and 75-ton size units.

Not Available

1978-10-01T23:59:59.000Z

51

WIPP Waste Information System Waste Container Data Report  

E-Print Network (OSTI)

WIPP Waste Information System Waste Container Data Report 06/06/2008 07:50 2.6 % LASB00411 % % Report Date Run by Report Site Id Container Number Waste Stream Data Status Code PEARCYM Version RP0360 Selection Criteria - Total Pages PRD02Instance 5 #12;Waste Isolation Pilot Plant Waste Container Data Report

52

WIPP Waste Information System Waste Container Data Report  

E-Print Network (OSTI)

WIPP Waste Information System Waste Container Data Report 06/06/2008 07:49 2.6 % LAS817174 % % Report Date Run by Report Site Id Container Number Waste Stream Data Status Code PEARCYM Version RP0360 Selection Criteria - Total Pages PRD02Instance 5 #12;Waste Isolation Pilot Plant Waste Container Data Report

53

2010 Smart Grid System Report Available (February 2012) | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2010 Smart Grid System Report Available (February 2012) 2010 Smart Grid System Report Available (February 2012) 2010 Smart Grid System Report Available (February 2012) February 24, 2012 - 2:58pm Addthis The Department of Energy has submitted the 2010 Smart Grid System Report in response to Section 1302 of Title XIII of the Energy Independence and Security Act (EISA), which directs the Secretary of Energy to report to Congress concerning the status of smart grid deployments nationwide and any regulatory or government barriers to continued deployment. This is the second installment of this report to Congress. A smart grid uses digital technology to improve the reliability, security, efficiency, and environmental impact of the electricity system, from large generation through the delivery systems to electricity consumers.

54

Project Assessment and Reporting System (PARS II) | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

byDeputySecretaryPoneman17May2010.pdf More Documents & Publications Earned Value (EV) Analysis and Project Assessment & Reporting System (PARS II) PARS II Data Quality...

55

SIMS Prototype System 4: performance test report  

DOE Green Energy (OSTI)

The results obtained during testing of a self-contained, preassembled air type solar system, designed for installation remote from the dwelling, to provide space heating and hot water are presented. Data analysis is included which documents the system performance and verifies the suitability of SIMS Prototype System 4 for field installation.

Not Available

1978-10-09T23:59:59.000Z

56

Acceptance Test Report for 241-U compressed air system  

SciTech Connect

This Acceptance Test Report (ATR) documents the results of acceptance testing of a newly upgraded compressed air system at 241-U Farm. The system was installed and the test successfully performed under work package 2W-92-01027.

Freeman, R.D.

1994-10-20T23:59:59.000Z

57

A. TECHNICAL PROGRESS REPORT ON METABOLISM IN NERVOUS SYSTEM  

SciTech Connect

Progress is reported in investigations into nucleic acid and protein metabolism in the central nervous system. Data are presented from biochemical and histochemical studies of metabolism in the nervous system of cats. (C.H.)

1961-01-01T23:59:59.000Z

58

Manzanita Hybrid Power system Project Final Report  

DOE Green Energy (OSTI)

The Manzanita Indian Reservation is located in southeastern San Diego County, California. The Tribe has long recognized that the Reservation has an abundant wind resource that could be commercially utilized to its benefit, and in 1995 the Tribe established the Manzanita Renewable Energy Office. Through the U.S. Department of Energy's Tribal Energy Program the Band received funds to install a hybrid renewable power system to provide electricity to one of the tribal community buildings, the Manzanita Activities Center (MAC building). The project began September 30, 1999 and was completed March 31, 2005. The system was designed and the equipment supplied by Northern Power Systems, Inc, an engineering company with expertise in renewable hybrid system design and development. Personnel of the National Renewable Energy Laboratory provided technical assistance in system design, and continued to provide technical assistance in system monitoring. The grid-connected renewable hybrid wind/photovoltaic system provides a demonstration of a solar/wind energy hybrid power-generating project on Manzanita Tribal land. During the system design phase, the National Renewable Energy Lab estimated that the wind turbine is expected to produce 10,000-kilowatt hours per year and the solar array 2,000-kilowatt hours per year. The hybrid system was designed to provide approximately 80 percent of the electricity used annually in the MAC building. The project proposed to demonstrate that this kind of a system design would provide highly reliable renewable power for community uses.

Trisha Frank

2005-03-31T23:59:59.000Z

59

2009 Smart Grid System Report (July 2009)  

Energy.gov (U.S. Department of Energy (DOE))

Section 1302 of Title XIII of the Energy Independence and Security Act of 2007 directs the Secretary of Energy to report to Congress concerning the status of smart grid deployments nationwide and...

60

Solar thermal power systems. Summary report  

DOE Green Energy (OSTI)

The work accomplished by the Aerospace Corporation from April 1973 through November 1979 in the mission analysis of solar thermal power systems is summarized. Sponsorship of this effort was initiated by the National Science Foundation, continued by the Energy Research and Development Administration, and most recently directed by the United States Department of Energy, Division of Solar Thermal Systems. Major findings and conclusions are sumarized for large power systems, small power systems, solar total energy systems, and solar irrigation systems, as well as special studies in the areas of energy storage, industrial process heat, and solar fuels and chemicals. The various data bases and computer programs utilized in these studies are described, and tables are provided listing financial and solar cost assumptions for each study. An extensive bibliography is included to facilitate review of specific study results and methodology.

Not Available

1980-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

AN ENERGY EFFICIENT WINDOW SYSTEM FINAL REPORT.  

E-Print Network (OSTI)

greenhouses, passive solar heating and other non-viewingpassive and active solar heating systems. the fact remainsthe expense of winter solar heating), Life Cycle Costing We

Authors, Various

2011-01-01T23:59:59.000Z

62

2007 NET SYSTEM POWER REPORT STAFFREPORT  

E-Print Network (OSTI)

-2007.......................................................................5 Figure 3: Natural Gas and Coal Shares of Net System Power Mix Become Larger 1999-2007.....7 List technologies used to generate electricity. Fuel types include coal, natural gas, nuclear, and other fuels of "unclaimed" coal and natural gas generation. Figure 2 illustrates the decrease in net system power between

63

Report on the SLC control system  

SciTech Connect

The SLC control system is based on a VAX 11/780 Host computer with approximately 50 microprocessor clusters which provide distributed intelligence and control of all CAMAC interface modules. This paper will present an overview of the system including current status and a description of the software architecture and communication protocols. 8 refs.

Phinney, N.

1985-05-01T23:59:59.000Z

64

Photovoltaic systems concept study. Final report  

DOE Green Energy (OSTI)

The work performed in the conceptual design and systems analysis of three sizes of photovoltaic solar electric power systems is contained in five volumes consisting of nine sections plus appendices. Separate abstracts were prepared for the two sections in this volume. (MHR)

Not Available

1977-04-01T23:59:59.000Z

65

Validation of the monthly power plant report system  

SciTech Connect

This report presents the results of a validation study of the Department of Energy's principal source of data on electricity generation, the Monthly Power Plant Report System, (FPC Form 4). This information system gathers monthly data on electricity generating capacity, electricity generation, fossil fuel consumption, and fossil fuel stocks for electric utilities within the United States.

1980-12-05T23:59:59.000Z

66

Ris Energy Report 7 Future low carbon energy systems  

E-Print Network (OSTI)

Risø Energy Report 7 Future low carbon energy systems Reprint of summary and recommendations Risø-R-1651(EN) October 2008 Edited by Hans Larsen and Leif Sønderberg Petersen #12;Risø Energy Report 7 Preface This Risø Energy Report, the seventh of a series that began in 2002, takes as its point

67

Photovoltaic systems for export application. Informal report  

DOE Green Energy (OSTI)

One approach to improving the competitiveness of photovoltaic systems is the development of designs specifically for export applications. In other words, where is it appropriate in a system design to incorporate components manufactured and/or assembled in the receiving country in order to improve the photovoltaic exports from the US? What appears to be needed is a systematic method of evaluating the potential for export from the US of PV systems for various application in different countries. Development of such a method was the goal of this project.

Duffy, J.; Campbell, H.; Sajo, A.; Sanz, E. [Univ. of Lowell, MA (United States)

1988-01-31T23:59:59.000Z

68

PC Electronic Data Reporting Option (PEDRO) System  

Gasoline and Diesel Fuel Update (EIA)

30 Mb of free disk space for the PEDRO system files, plus up to 10 Mb for each survey Internet Service Provider (ISP) with appropriate link or modem Downloading and Installing...

69

PC Electronic Data Reporting Option (PEDRO) System  

U.S. Energy Information Administration (EIA)

Windows-based personal computer (PC) Windows NT, 2000, XP, or Vista; Approximately 30 Mb of free disk space for the PEDRO system files, plus up to 10 Mb for each survey;

70

Water-storage-tube systems. Final report  

DOE Green Energy (OSTI)

Passive solar collection/storage/distribution systems were surveyed, designed, fabricated, and mechanically and thermally tested. The types studied were clear and opaque fiberglass tubes, metal tubes with plastic liners, and thermosyphoning tubes. (MHR)

Hemker, P.

1981-12-24T23:59:59.000Z

71

Advanced Turbine Systems Program. Topical report  

SciTech Connect

The Allison Gas Turbine Division (Allison) of General Motors Corporation conducted the Advanced Turbine Systems (ATS) program feasibility study (Phase I) in accordance with the Morgantown Energy Technology Center`s (METC`s) contract DE-AC21-86MC23165 A028. This feasibility study was to define and describe a natural gas-fired reference system which would meet the objective of {ge}60% overall efficiency, produce nitrogen oxides (NO{sub x}) emissions 10% less than the state-of-the-art without post combustion controls, and cost of electricity of the N{sup th} system to be approximately 10% below that of the current systems. In addition, the selected natural gas-fired reference system was expected to be adaptable to coal. The Allison proposed reference system feasibility study incorporated Allison`s long-term experience from advanced aerospace and military technology programs. This experience base is pertinent and crucial to the success of the ATS program. The existing aeroderivative technology base includes high temperature hot section design capability, single crystal technology, advanced cooling techniques, high temperature ceramics, ultrahigh turbomachinery components design, advanced cycles, and sophisticated computer codes.

1993-03-01T23:59:59.000Z

72

Advanced lubrication systems and materials. Final report  

DOE Green Energy (OSTI)

This report described the work conducted at the National Institute of Standards and Technology under an interagency agreement signed in September 1992 between DOE and NIST for 5 years. The interagency agreement envisions continual funding from DOE to support the development of fuel efficient, low emission engine technologies in terms of lubrication, friction, and wear control encountered in the development of advanced transportation technologies. However, in 1994, the DOE office of transportation technologies was reorganized and the tribology program was dissolved. The work at NIST therefore continued at a low level without further funding from DOE. The work continued to support transportation technologies in the development of fuel efficient, low emission engine development. Under this program, significant progress has been made in advancing the state of the art of lubrication technology for advanced engine research and development. Some of the highlights are: (1) developed an advanced high temperature liquid lubricant capable of sustaining high temperatures in a prototype heat engine; (2) developed a novel liquid lubricant which potentially could lower the emission of heavy duty diesel engines; (3) developed lubricant chemistries for ceramics used in the heat engines; (4) developed application maps for ceramic lubricant chemistry combinations for design purpose; and (5) developed novel test methods to screen lubricant chemistries for automotive air-conditioning compressors lubricated by R-134a (Freon substitute). Most of these findings have been reported to the DOE program office through Argonne National Laboratory who manages the overall program. A list of those reports and a copy of the report submitted to the Argonne National Laboratory is attached in Appendix A. Additional reports have also been submitted separately to DOE program managers. These are attached in Appendix B.

Hsu, S.

1998-05-07T23:59:59.000Z

73

WRAP TRUPACT loading systems operational test report  

SciTech Connect

This Operational Test Report documents the operational testing of the TRUPACT process equipment HNF-3918, Revision 0, TRUPACT Operational Test Procedure. The test accomplished the following: Procedure validation; Facility equipment interface; Facility personnel support; and Subcontractor personnel support interface. Field changes are documented as test exceptions with resolutions. All resolutions are completed or a formal method is identified to track the resolution through to completion.

DOSRAMOS, E.V.

1999-09-01T23:59:59.000Z

74

Multipurpose Canister System Design Synopsis Report  

Science Conference Proceedings (OSTI)

The multipurpose canister (MPC) concept can simplify the management of spent nuclear fuel by enclosing the fuel permanently in a canister that can be used for long-term dry storage at a utility site, transportation to an interim federal storage facility, and eventual disposal in a repository. This synopsis report summarizes the key design and analysis features of the U.S. Department of Energy (DOE) MPC program.

1997-09-16T23:59:59.000Z

75

Autonomous microexplosives subsurface tracing system final report.  

SciTech Connect

The objective of the autonomous micro-explosive subsurface tracing system is to image the location and geometry of hydraulically induced fractures in subsurface petroleum reservoirs. This system is based on the insertion of a swarm of autonomous micro-explosive packages during the fracturing process, with subsequent triggering of the energetic material to create an array of micro-seismic sources that can be detected and analyzed using existing seismic receiver arrays and analysis software. The project included investigations of energetic mixtures, triggering systems, package size and shape, and seismic output. Given the current absence of any technology capable of such high resolution mapping of subsurface structures, this technology has the potential for major impact on petroleum industry, which spends approximately $1 billion dollar per year on hydraulic fracturing operations in the United States alone.

Engler, Bruce Phillip; Nogan, John; Melof, Brian Matthew; Uhl, James Eugene; Dulleck, George R., Jr.; Ingram, Brian V.; Grubelich, Mark Charles; Rivas, Raul R.; Cooper, Paul W.; Warpinski, Norman Raymond; Kravitz, Stanley H.

2004-04-01T23:59:59.000Z

76

New passive solar cooking system. Final report  

SciTech Connect

The development of a solar cooking system which uses a phase change process to passively transfer heat from a collector to a cooker is presented. In the design of this cooking system steam is produced in the collector and then is used as the heat transfer fluid in the cooker. The most efficient use of the system is to heat food directly by condensing the steam onto the food, whereas a heat exchanger is necessary to heat an oven or a frying pan. A pressure cooker was successfully built and tested using the steam from the collector. Brief discussions on the collector design and performance, and heat storage phase change materials are provided. (BCS)

Schlussler, L.

1981-11-01T23:59:59.000Z

77

Available Reports in the Business Intelligence System Number Subject Area Audience Report Title Description Report Prompts Report Folder Location Role(s) with Access  

E-Print Network (OSTI)

Michigan State University. All rights reserved. 2 #12;Available Reports in the Business Intelligence System State University. All rights reserved. 12 #12;Available Reports in the Business Intelligence System State University. All rights reserved. 13 #12;Available Reports in the Business Intelligence System

Landis, Doug

78

EISA Compliance Tracking System Reports and Data | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EISA Compliance Tracking System Reports and Data EISA Compliance Tracking System Reports and Data EISA Compliance Tracking System Reports and Data October 8, 2013 - 2:06pm Addthis The Federal Energy Management Program (FEMP) provides links to reports and data illustrating Federal progress in meeting the requirements outlined in Section 432 of the Energy Independence and Security Act of 2007 (EISA) (42 U.S.C. 8253(f)) available through the EISA 432 Compliance Tracking System (CTS). EISA 432 CTS Data Levels Top-tier agency aggregates, representing all reported data subject to the EISA 432 requirements Facility-level detailed data that excludes information for facilities that have requested exemption from public disclosure for national-security purposes. Access Data Federal Government Compliance Overview: View key CTS metrics and aggregates

79

System integration of marketable subsystems (third collection of progress reports)  

DOE Green Energy (OSTI)

Six monthly progress reports are included, covering the period from July 1978 through December 1978. This NASA/MSFC activity calls for work in five major areas: systems integration of marketable subsystems; development, design, and building of site data acquisition subsystems; development and operation of the central data processing system; operation of the MSFC Solar Test Facility; and systems analysis. (MHR)

Not Available

1979-02-01T23:59:59.000Z

80

Page 1 of 12 California Integrated Renewable Energy Systems Report  

E-Print Network (OSTI)

hydro systems is in development with the intent to also address ocean energy systems in the future Page 1 of 12 California Integrated Renewable Energy Systems Report California Renewable Energy Collaborative UC Davis Energy Institute University of California I Shields Avenue Davis

Islam, M. Saif

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Solar thermal repowering systems integration. Final report  

DOE Green Energy (OSTI)

This report is a solar repowering integration analysis which defines the balance-of-plant characteristics and costs associated with the solar thermal repowering of existing gas/oil-fired electric generating plants. Solar repowering interface requirements for water/steam and salt or sodium-cooled central receivers are defined for unit sizes ranging from 50 MWe non-reheat to 350 MWe reheat. Finally balance-of-plant cost estimates are presented for each of six combinations of plant type, receiver type and percent solar repowering.

Dubberly, L. J.; Gormely, J. E.; McKenzie, A. W.

1979-08-01T23:59:59.000Z

82

Natural System Evaluation and Tool Development FY11 Progress Report |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Natural System Evaluation and Tool Development FY11 Progress Report Natural System Evaluation and Tool Development FY11 Progress Report Natural System Evaluation and Tool Development FY11 Progress Report The report describes selected aspects of progress for four major tasks: (1) development of a detailed R&D plan for natural system evaluation and tool development; (2) in-depth analsis of key attributes and new concepts identified in the R&D plan; (3) preliminary demonstration of new modeling and experimental tools; and (4) conceptual design of a databse for natural system evaluation. This includes discussions related to: 1) discrete fracture network simulation; 2) spatial heterogeneity in Kd; 3) literature review of radionuclide interactions with clay/clay minerals; 4) behavior of aqueous Pu(IV) and intrinsic Pu(IV) nanocolloids; 5) mechanical response of clay,

83

Photovoltaic systems concept study. Final report  

DOE Green Energy (OSTI)

The following appendices are included: economic theory, electric utilities, and peak load pricing; evaluating the total cost of an on-site solar energy system; derivation of PEPS cost model; PEPS economic analysis model; scenarios; the effect of governmental ''subsidies'' on the nuclear power industry; discussion of energy industry subsidies; extension of the Hottel-Whillier-Bliss model to the analysis of combined photovoltaic/thermal flat plate collectors; analysis of solar-augmented rock-bed/heat pump system; TRNSYS results for Washington, D.C. residence with air collectors, rock-bed storage, and parallel Airesearch heat pump; tabulation of electrical loads for Phoenix, Riverside, and Cleveland using a simplified hourly method; evaporative air coolers; cooling efficiency and electrical consumption; and Hoover Dam operation. (MHR)

Not Available

1977-04-01T23:59:59.000Z

84

Tank waste remediation system mission analysis report  

SciTech Connect

This document describes and analyzes the technical requirements that the Tank Waste Remediation System (TWRS) must satisfy for the mission. This document further defines the technical requirements that TWRS must satisfy to supply feed to the private contractors` facilities and to store or dispose the immobilized waste following processing in these facilities. This document uses a two phased approach to the analysis to reflect the two-phased nature of the mission.

Acree, C.D.

1998-01-09T23:59:59.000Z

85

Generic Disposal System Modeling, Fiscal Year 2011 Progress Report |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Disposal System Modeling, Fiscal Year 2011 Progress Report Disposal System Modeling, Fiscal Year 2011 Progress Report Generic Disposal System Modeling, Fiscal Year 2011 Progress Report The UFD Campaign is developing generic disposal system models (GDSM) of different disposal environments and waste form options. Currently, the GDSM team is investigating four main disposal environment options: mined repositories in three geologic media (salt, clay, and granite) and the deep borehole concept in crystalline rock (DOE 2010d). Further developed the individual generic disposal system (GDS) models for salt, granite, clay, and deep borehole disposal environments. GenericDisposalSystModelFY11.pdf More Documents & Publications Integration of EBS Models with Generic Disposal System Models TSPA Model Development and Sensitivity Analysis of Processes Affecting

86

Advanced DES System Evaluation Interim Report  

Science Conference Proceedings (OSTI)

A portfolio of electric energy storage options is emerging that provides electric utilities with new options for grid support and operational flexibility. This research and development (RD) project was initiated to assess and test an emerging zinc-bromine (Zn-Br) flow battery in an electric distribution system and to provide input on a utility application specification. This technology is based on a flow battery developed by Exxon in the 1970s and '80s and is now being advanced and commercialized by Prem...

2009-05-19T23:59:59.000Z

87

W-026, acceptance test report manipulator system  

Science Conference Proceedings (OSTI)

The purpose of the WRAP Manipulator System Acceptance Test Plan (ATP) is to verify that the 4 glovebox sets of WRAP manipulator components, including rail/carriage, slave arm, master controller and auxiliary equipment, meets the requirements of the functional segments of 14590 specification. The demonstration of performance elements of the ATP are performed as a part of the Assembly specifications. Manipulator integration is integrated in the performance testing of the gloveboxes. Each requirement of the Assembly specification will be carried out in conjunction with glovebox performance tests.

Watson, T.L.

1997-04-15T23:59:59.000Z

88

Innovative technology summary report: Transportable vitrification system  

Science Conference Proceedings (OSTI)

At the end of the cold war, many of the Department of Energy`s (DOE`s) major nuclear weapons facilities refocused their efforts on finding technically sound, economic, regulatory compliant, and stakeholder acceptable treatment solutions for the legacy of mixed wastes they had produced. In particular, an advanced stabilization process that could effectively treat the large volumes of settling pond and treatment sludges was needed. Based on this need, DOE and its contractors initiated in 1993 the EM-50 sponsored development effort required to produce a deployable mixed waste vitrification system. As a consequence, the Transportable Vitrification System (TVS) effort was undertaken with the primary requirement to develop and demonstrate the technology and associated facility to effectively vitrify, for compliant disposal, the applicable mixed waste sludges and solids across the various DOE complex sites. After 4 years of development testing with both crucible and pilot-scale melters, the TVS facility was constructed by Envitco, evaluated and demonstrated with surrogates, and then successfully transported to the ORNL ETTP site and demonstrated with actual mixed wastes in the fall of 1997. This paper describes the technology, its performance, the technology applicability and alternatives, cost, regulatory and policy issues, and lessons learned.

NONE

1998-09-01T23:59:59.000Z

89

California Integrated Renewable Energy Systems Report California Renewable Energy Collaborative  

E-Print Network (OSTI)

1 California Integrated Renewable Energy Systems Report California Renewable Energy Collaborative UC Davis Energy Institute University of California I Shields Avenue Davis, California 95616 California Renewable Energy Center: Vision and Development Metrics Principal Author: Gerald Braun CREC

Islam, M. Saif

90

Status report on the Advanced Light Source control system  

SciTech Connect

This paper is a status report on the ADVANCED LIGHT SOURCE (ALS) control system. The current status, performance data, and future plans will be discussed. Manpower, scheduling, and costs issues are addressed.

Magyary, S.; Chin, M.; Fahmie, M.; Lancaster, H.; Molinari, P.; Robb, A.; Timossi, C.; Young, J.

1991-11-11T23:59:59.000Z

91

Standard-C hydrogen monitoring system. Acceptance test report  

DOE Green Energy (OSTI)

Project W-369, Watch List Tank Hydrogen Monitors, installed a Standard-C Hydrogen Monitoring System (SHMS) on Flammable Gas Watch List waste tank 104-AN. This document is the acceptance test report for the acceptance testing of the SHMS.

Lott, D.T.

1995-05-17T23:59:59.000Z

92

Prototype solar heating and cooling systems. Monthly progress reports  

DOE Green Energy (OSTI)

This report is a combination of monthly progress reports submitted by AiResearch Manufacturing Company. It contains a summary of activities and progress made from November 1, 1978, to February 28, 1979. AiResearch Manufacturing Company is developing prototype solar heating/cooling systems under NASA Contract NAS8-32091. This effort calls for the development, manufacture, test, system installation, maintenance, problem resolution, and performance evaluation.

Not Available

1979-04-01T23:59:59.000Z

93

Information systems and the overview report for computing curricula 2004  

Science Conference Proceedings (OSTI)

My purpose is to inform you of the draft "Overview Report" for Computing Curricula 2004 and Information Systems (IS) role in it. This draft report is available for comment. It is the first volume in a computing compendium, referred to as Computing Curricula. ...

John T. Gorgone

2004-12-01T23:59:59.000Z

94

Waste retrieval sluicing system data acquisition system acceptance test report  

SciTech Connect

This document describes the test procedure for the Project W-320 Tank C-106 Sluicing Data Acquisition System (W-320 DAS). The Software Test portion will test items identified in the WRSS DAS System Description (SD), HNF-2115. Traceability to HNF-2115 will be via a reference that follows in parenthesis, after the test section title. The Field Test portion will test sensor operability, analog to digital conversion, and alarm setpoints for field instrumentation. The W-320 DAS supplies data to assist thermal modeling of tanks 241-C-106 and 241-AY-102. It is designed to be a central repository for information from sources that would otherwise have to be read, recorded, and integrated manually. Thus, completion of the DAS requires communication with several different data collection devices and output to a usable PC data formats. This test procedure will demonstrate that the DAS functions as required by the project requirements stated in Section 3 of the W-320 DAS System Description, HNF-2115.

Bevins, R.R.

1998-07-31T23:59:59.000Z

95

Project Assessment and Reporting System (PARS II) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Project Assessment and Reporting System (PARS II) Project Assessment and Reporting System (PARS II) Project Assessment and Reporting System (PARS II) Welcome to PARS II PARS II is the Department's official "System of Record" for capital asset project performance information. Because PARS II uses the same data as maintained in our contractors' project management systems, everyone from the Federal Project Director's staff to the Secretary of Energy will have easy access to the same data. The PARS II software application is managed by the MA Office of Engineering and Construction Management and is used by federal and contractor personnel across the nation to record and track the progress of major construction and environmental cleanup projects. Questions or comments about PARS II should be directed to the PARS II Help

96

Harrison Radiator Division's Energy Management, Reporting and Accounting System  

E-Print Network (OSTI)

Energy management is essential for obtaining the lowest possible product manufacturing cost. Many systems have been created over the years to manage the energy used in manufacturing. However, for a variety of reasons, most of them never reached their full potential. Harrison Radiator first installed an energy management system in 1973. Energy consumption was reduced 42% from 1973 through 1984. However, the gains the last couple of years have been small. In 1984, important changes were made to the system and energy reporting was added, resulting in 1985 energy consumption reduction of about 16%. This paper will briefly describe Harrison's successful energy management, reporting and accounting system. Examples of reports, available data, information flow and benefits will be covered, with special mention of all factors that lead to our system's success.

Goubeaux, R. J.

1986-06-01T23:59:59.000Z

97

INL Control System Situational Awareness Technology Annual Report 2012  

Science Conference Proceedings (OSTI)

The overall goal of this project is to develop an interoperable set of tools to provide a comprehensive, consistent implementation of cyber security and overall situational awareness of control and sensor network implementations. The operation and interoperability of these tools will fill voids in current technological offerings and address issues that remain an impediment to the security of control systems. This report provides an FY 2012 update on the Sophia, Mesh Mapper, Intelligent Cyber Sensor, and Data Fusion projects with respect to the year-two tasks and annual reporting requirements of the INL Control System Situational Awareness Technology report (July 2010).

Gordon Rueff; Bryce Wheeler; Todd Vollmer; Tim McJunkin; Robert Erbes

2012-10-01T23:59:59.000Z

98

Utility Battery Storage Systems Program report for FY93  

DOE Green Energy (OSTI)

Sandia National Laboratories, New Mexico, conducts the Utility Battery Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Energy Management. In this capacity, Sandia is responsible for the engineering analyses, contract development, and testing of rechargeable batteries and systems for utility-energy-storage applications. This report details the technical achievements realized during fiscal year 1993.

Butler, P.C.

1994-02-01T23:59:59.000Z

99

Hydrogen Storage Systems Analysis Working Group Meeting: Summary Report  

NLE Websites -- All DOE Office Websites (Extended Search)

Held in Conjunction with the DOE Hydrogen Program Annual Merit Review Crystal Gateway Marriott, Arlington, VA June 11, 2008 SUMMARY REPORT Compiled by Romesh Kumar Argonne National Laboratory and Elvin Yzugullu Sentech, Inc. July 18, 2008 SUMMARY REPORT Hydrogen Storage Systems Analysis Working Group Meeting June 11, 2008 Crystal Gateway Marriott, Arlington, VA Meeting Objectives This meeting was one of a continuing series of biannual meetings of the Hydrogen Storage Systems Analysis Working Group (SSAWG). The objective of these meetings is to bring together the DOE research community involved in systems analysis of hydrogen storage materials and processes for information exchange and to update the researchers on related

100

FY 2004 Annual Progress Report for Heavy Vehicle Systems Optimization  

NLE Websites -- All DOE Office Websites (Extended Search)

HEAVY HEAVY VEHICLE SYSTEMS OPTIMIZATION FreedomCAR and Vehicle Technologies Program U.S. Department of Energy FreedomCAR and Vehicle Technologies Program 1000 Independence Avenue, S.W. Washington, D.C. 20585-0121 FY 2004 Annual Progress Report for Heavy Vehicle Systems Optimization Energy Efficiency and Renewable Energy FreedomCAR and Vehicle Technologies Program Approved by Dr. Sidney Diamond Technology Area Development Specialist February 2005 Heavy Vehicle Systems Optimization Program FY 2004 Annual Report iii Contents Foreword by Dr. Sidney Diamond, FreedomCAR and Vehicle Technologies Program, Energy Efficiency and Renewable Energy, U.S. Department of Energy ................................. 1 I. Aerodynamic Drag Reduction......................................................................................................

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

CERCLA reporting requirements, DOE occurrence reporting, and the DOE Emergency Management System. CERCLA Information Brief  

SciTech Connect

The Emergency Management System (EMS) provides a structure for reporting and processing operations information related to DOE owned/operated facilities. Hazardous Substance (HS) releases are subject to reporting requirements under the EMS as well as under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). CERCLA requires reporting of HS releases into the environment in amounts greater than or equal to Reportable Quantities (RQs). This Information Brief elaborates on earlier CERCLA reporting and response process information Briefs by providing a general explanation of these CERCLA or EMS requirements, procedures, and events as they pertain to releases of HS`s at DOE facilities.

Dailey, R.

1993-10-01T23:59:59.000Z

102

Utility battery storage systems program report for FY 94  

DOE Green Energy (OSTI)

Sandia National Laboratories, New Mexico, conducts the Utility Battery Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Energy Management. The goal of this program is to assist industry in developing cost-effective battery systems as a utility resource option by 2000. Sandia is responsible for the engineering analyses, contracted development, and testing of rechargeable batteries and systems for utility energy storage applications. This report details the technical achievements realized during fiscal year 1994.

Butler, P.C.

1995-03-01T23:59:59.000Z

103

Advanced Thermal Barrier Coating System Development. Technical progress report  

Science Conference Proceedings (OSTI)

The objectives of the program are to provide an improved TBC system with increased temperature capability and improved reliability relative to current state of the art TBC systems. The development of such a coating system is essential to the ATS engine meeting its objectives. The base program consists of three phases: Phase I: Program Planning - Complete; Phase II: Development - Complete; and Phase III: Selected Specimen - Bench Test. Work was performed in Phase II and III of the program during the reporting period.

None

2000-01-13T23:59:59.000Z

104

Energy storage systems program report for FY1996  

DOE Green Energy (OSTI)

Sandia National Laboratories, New Mexico, conducts the Energy Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Utility Technologies. The goal of this program is to assist industry in developing cost-effective energy storage systems as a resource option by 2000. Sandia is responsible for the engineering analyses, contracted development, and testing of energy storage systems for stationary applications. This report details the technical achievements realized during fiscal year 1996.

Butler, P.C.

1997-05-01T23:59:59.000Z

105

Energy Storage Systems Program Report for FY99  

DOE Green Energy (OSTI)

Sandia National Laboratories, New Mexico, conducts the Energy Storage Systems Program, which is sponsored by the US Department of Energy's Office of Power Technologies. The goal of this program is to develop cost-effective electric energy storage systems for many high-value stationary applications in collaboration with academia and industry. Sandia National Laboratories is responsible for the engineering analyses, contracted development, and testing of energy storage components and systems. This report details the technical achievements realized during fiscal year 1999.

BOYES,JOHN D.

2000-06-01T23:59:59.000Z

106

SNAP 29 power supply system. Ninth quarterly progress report  

SciTech Connect

Progress during the period from Oct. through December 1968 in the development of the SNAP 29 battery, a radioisotope-fueled thermoelectric generator (RTG) system for spacecraft power supplies, is reported. Information is included on: fabrication and testing of RTG components; systems evaluation and integration; reliability analysis and prediction; reentry trajectory and heating rates for various burn-up element configurations; and system safety evaluation. (LCL)

1969-01-01T23:59:59.000Z

107

Power plant system assessment. Final report. SP-100 Program  

SciTech Connect

The purpose of this assessment was to provide system-level insights into 100-kWe-class space reactor electric systems. Using these insights, Rockwell was to select and perform conceptual design studies on a ''most attractive'' system that met the preliminary design goals and requirements of the SP-100 Program. About 4 of the 6 months were used in the selection process. The remaining 2 months were used for the system conceptual design studies. Rockwell completed these studies at the end of FY 1983. This report summarizes the results of the power plant system assessment and describes our choice for the most attractive system - the Rockwell SR-100G System (Space Reactor, 100 kWe, Growth) - a lithium-cooled UN-fueled fast reactor/Brayton turboelectric converter system.

Anderson, R.V.; Atkins, D.F.; Bost, D.S.; Berman, B.; Clinger, D.A.; Determan, W.R.; Drucker, G.S.; Glasgow, L.E.; Hartung, J.A.; Harty, R.B.

1983-10-31T23:59:59.000Z

108

Hydrogen Storage Systems Analysis Meeting: Summary Report, March 29, 2005  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen Storage Systems Analysis Meeting Hydrogen Storage Systems Analysis Meeting 955 L'Enfant Plaza North, SW, Suite 6000 Washington, DC 20024-2168 March 29, 2005 SUMMARY REPORT Compiled by Romesh Kumar Argonne National Laboratory June 20, 2005 SUMMARY REPORT Hydrogen Storage Systems Analysis Meeting March 29, 2005 955 L'Enfant Plaza, North, SW, Suite 6000 Washington, DC 20024-2168 Meeting Objectives The objective of this meeting was to familiarize the DOE research community involved in hydrogen storage materials and process development with the systems analysis work being carried out within the DOE program. In particular, Argonne National Laboratory (ANL) has been tasked to develop models of on-board and off-board hydrogen storage systems based on the various materials and technologies being developed at the DOE Centers of Excellence and

109

Hydrogen Storage Systems Analysis Working Group Meeting: Summary Report  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen Storage Systems Analysis Working Group Meeting Hydrogen Storage Systems Analysis Working Group Meeting Argonne DC Offices L'Enfant Plaza, Washington, DC December 4, 2007 SUMMARY REPORT Compiled by Romesh Kumar Argonne National Laboratory and Kristin Deason Sentech, Inc. January 16, 2008 SUMMARY REPORT Hydrogen Storage Systems Analysis Working Group Meeting December 4, 2007 Argonne DC Offices, L'Enfant Plaza, Washington, DC Meeting Objectives This meeting was one of a continuing series of biannual meetings of the Hydrogen Storage Systems Analysis Working Group (SSAWG). The objective of these meetings is to bring together the DOE research community involved in systems analysis of hydrogen storage materials and processes for information exchange and to update the researchers on related developments within the DOE program. A major thrust of these meetings is to leverage

110

Smart Grid System Report U.S. Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Smart Grid Smart Grid System Report U.S. Department of Energy July 2009 SEC. 1302. SMART GRID SYSTEM REPORT The Secretary, acting through the Assistant Secretary of the Office of Electricity Delivery and Energy Reliability (referred to in this section as the "OEDER") and through the Smart Grid Task Force established in section 1303, shall, after consulting with any interested individual or entity as appropriate, no later than one year after enactment and every two years thereafter, report to Congress concerning the status of smart grid deployments nationwide and any regulatory or government barriers to continued deployment. The report shall provide the current status and prospects of smart grid development, including information on technology penetration, communications network capabilities,

111

Contractor Performance Assessment Reporting System (CPARS) | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Contractor Performance Assessment Reporting System (CPARS) Contractor Performance Assessment Reporting System (CPARS) Contractor Performance Assessment Reporting System (CPARS) The CPAR assesses a contractor's performance, both positive and negative, and provides a record on a given contract during a specified period of time. Each assessment must be based on objective data (or measurable, subjective data when objective data is not available) supportable by program and contract management data. The CPARS process is designed with a series of checks-and-balances to facilitate the objective and consistent evaluation of contractor performance. Both Government and contractor perspectives are captured on the CPAR form. The opportunity to review/comment on the CPAR by the designated Government and contractor personnel together makes a complete CPAR.

112

National high-level waste systems analysis report  

SciTech Connect

This report documents the assessment of budgetary impacts, constraints, and repository availability on the storage and treatment of high-level waste and on both existing and pending negotiated milestones. The impacts of the availabilities of various treatment systems on schedule and throughput at four Department of Energy sites are compared to repository readiness in order to determine the prudent application of resources. The information modeled for each of these sites is integrated with a single national model. The report suggests a high-level-waste model that offers a national perspective on all high-level waste treatment and storage systems managed by the Department of Energy.

Kristofferson, K.; Oholleran, T.P.; Powell, R.H.

1995-09-01T23:59:59.000Z

113

Report on emergency electrical power supply systems for nuclear fuel cycle and reactor facilities security systems  

SciTech Connect

The report includes information that will be useful to those responsible for the planning, design and implementation of emergency electric power systems for physical security and special nuclear materials accountability systems. Basic considerations for establishing the system requirements for emergency electric power for security and accountability operations are presented. Methods of supplying emergency power that are available at present and methods predicted to be available in the future are discussed. The characteristics of capacity, cost, safety, reliability and environmental and physical facility considerations of emergency electric power techniques are presented. The report includes basic considerations for the development of a system concept and the preparation of a detailed system design.

1977-01-01T23:59:59.000Z

114

2007 Heavy Vehicle Systems Optimization Program Annual Report  

NLE Websites -- All DOE Office Websites (Extended Search)

HEAVY VEHiclE SYSTEMS HEAVY VEHiclE SYSTEMS OPTiMiZATiON PROGRAM V EH icl E T E c HNO l OG i ES P ROGRAM Less dependence on foreign oil today, and transition to a petroleum-free, emissions-free vehicle tomorrow. 2 0 0 7 a n n u a l p r o g r e s s r e p o r t U.S. Department of Energy Vehicle Technologies Program 1000 Independence Avenue, S.W. Washington, DC 20585-0121 FY 2007 Annual Progress Report for Heavy Vehicle Systems Optimization Program Submitted to: U.S. Department of Energy Energy Efficiency and Renewable Energy Vehicle Technologies Program Advanced Vehicle Technology Analysis and Evaluation Lee Slezak, Technology Manager Heavy Vehicle Systems Optimization Program FY 2007 Annual Report CONTENTS I. AERODYNAMIC DRAG REDUCTION ........................................................................... 1

115

Hydrgoen Storage Systems Analysis Working Group Meeting Summary Report  

NLE Websites -- All DOE Office Websites (Extended Search)

Systems Analysis Working Group Meeting Systems Analysis Working Group Meeting 2007 Hydrogen Program Annual Review Crystal Gateway Marriott, Arlington, VA May 17, 2007 SUMMARY REPORT Compiled by Romesh Kumar Argonne National Laboratory and Elvin Yuzugullu Sentech, Inc. June 28, 2007 SUMMARY REPORT Hydrogen Storage Systems Analysis Working Group Meeting May 17, 2007 Crystal Gateway Marriott, Arlington, VA Meeting Objectives This meeting was one of a continuing series of biannual meetings of this Working Group. The objective of these meetings is to bring together the DOE research community involved in systems analysis of hydrogen storage materials and processes for information exchange and to update the researchers on related developments within the DOE program. A major thrust of these meetings is to leverage expertise, complement related work of different individuals and

116

Annex A Metrics for the Smart Grid System Report  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Annex A Annex A Metrics for the Smart Grid System Report A.iii Table of Contents Introduction ........................................................................................................................................... A.1 Metric #1: The Fraction of Customers and Total Load Served by Real-Time Pricing, Critical Peak Pricing, and Time-of-Use Pricing ........................................................................................ A.2 Metric #2: Real-Time System Operations Data Sharing ...................................................................... A.9 Metric #3: Standard Distributed Resource Connection Policies .......................................................... A.18 Metric #4: Regulatory Recovery for Smart Grid Investments ............................................................. A.23

117

Communications Security Analysis for Control System Networks: Preliminary Report  

Science Conference Proceedings (OSTI)

Communications capabilities in the control system network are expanding and security issues are becoming more important as the electric power industry migrates from relatively slow, serial communications to high-speed, asynchronous communications. This report surveys current and evolving wired and wireless high-speed communication technologies to create a roadmap for planning control system network upgrades before regulation or equipment obsolescence and reliability concerns become issues. Technologies s...

2007-02-15T23:59:59.000Z

118

Utility Battery Storage Systems Program Report for FY92  

DOE Green Energy (OSTI)

This report documents the fiscal year 1992 activities of the, Utility Battery Storage Systems Program (UBS) of the US Department of Energy (DOE), Office of Energy Management (OEM). The UBS program is conducted by Sandia National Laboratories (SNL). UBS is responsible for the engineering development of integrated battery systems for use in utility-energy-storage (UES) and other stationary applications. Development is accomplished primarily through cost-shared contracts with industrial organizations. An important part of the development process is the identification, analysis, and characterization of attractive UES applications. UBS is organized into five projects: Utility Battery Systems Analyses; Battery Systems Engineering; Zinc/Bromine; Sodium/Sulfur; Supplemental Evaluations and Field Tests. The results of the Utility Systems Analyses are used to identify several utility-based applications for which battery storage can effectively solve existing problems. The results will also specify the engineering requirements for widespread applications and motivate and define needed field evaluations of full-size battery systems.

Butler, P.C.

1993-01-01T23:59:59.000Z

119

Reference guide to small cogeneration systems for utilities. Final report  

SciTech Connect

This report covers systems performance and cost data for selected smaller cogeneration systems, which are defined generally as those cogeneration systems in the range below 5 megawatts. The data presented in this guide are expected to be used in two main ways. First, the data can be used to extend the existing DEUS Computer Evaluation Model data base to the smaller cogeneration systems. Second, the data will serve as a general guide to smaller cogeneration systems for use by the utilities companies and others. The data pertain to the following cogeneration system: gas turbine with heat recovery boiler, back pressure and extraction/condensing steam turbine, combined cycle, internal combustion (reciprocating) engine, steam bottoming cycle using industrial process exhaust, and gas turbine topping cycle with standard industrial process steam generators. A no-cogeneration base case is included for comparison purposes.

Rodden, R.M.; Boyen, J.L.; Waters, M.H.

1986-02-01T23:59:59.000Z

120

System Advisor Model: Flat Plate Photovoltaic Performance Modeling Validation Report  

SciTech Connect

The System Advisor Model (SAM) is a free software tool that performs detailed analysis of both system performance and system financing for a variety of renewable energy technologies. This report provides detailed validation of the SAM flat plate photovoltaic performance model by comparing SAM-modeled PV system generation data to actual measured production data for nine PV systems ranging from 75 kW to greater than 25 MW in size. The results show strong agreement between SAM predictions and field data, with annualized prediction error below 3% for all fixed tilt cases and below 8% for all one axis tracked cases. The analysis concludes that snow cover and system outages are the primary sources of disagreement, and other deviations resulting from seasonal biases in the irradiation models and one axis tracking issues are discussed in detail.

Freeman, J.; Whitmore, J.; Kaffine, L.; Blair, N.; Dobos, A. P.

2013-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

U.S. - Canada Power System Outage Task Force: Final Report on...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

- Canada Power System Outage Task Force: Final Report on the Implementation of Task Force Recommendations U.S. - Canada Power System Outage Task Force: Final Report on the...

122

TESLA Report 2003-08 Cavity control system  

E-Print Network (OSTI)

TESLA Report 2003-08 Cavity control system essential modeling for TESLA linear accelerator Tomasz of Technology, Poland Stefan Simrock DESY, TESLA, Hamburg, Germany ABSTRACT The pioneering TESLA linear are proposed. Keywords: TESLA, free electron laser, accelerator, high power microwave cavity, vector and phasor

123

Ocean energy systems. Quarterly report, July-September 1982  

DOE Green Energy (OSTI)

This quarterly report summarizes work on the following tasks as of September 30, 1982: (1) OTEC pilot plant conceptual design review; (2) OTEC methanol; (3) financial and legal considerations in OTEC implementation; (4) GEOTEC resource exploration at Adak, Alaska, and Lualualei, Hawaii; (5) preliminary GEOTEC plant cost estimates; and (6) supervision of testing of pneumatic wave energy conversion system.

Not Available

1982-09-30T23:59:59.000Z

124

Advanced thermal barrier coating system development. Technical progress report  

Science Conference Proceedings (OSTI)

This report describes work to develop new thermal barrier coating systems, which will be essential to the operation of the ATS engine which is under development. Work is at the stage of process improvement and bond coat improvement, along with proof testing of the coatings under thermal conditions typical of what can be expected in the ATS engine.

NONE

1998-03-16T23:59:59.000Z

125

Automated Energy Distribution and Reliability System (AEDR): Final Report  

Science Conference Proceedings (OSTI)

This report describes Northern Indiana Public Service Co. project efforts to develop an automated energy distribution and reliability system. The purpose of this project was to implement a database-driven GIS solution that would manage all of the company's gas, electric, and landbase objects.

Buche, D. L.

2008-07-01T23:59:59.000Z

126

Automated Energy Distribution and Reliability System Status Report  

Science Conference Proceedings (OSTI)

This report describes Northern Indiana Public Service Co. project efforts to develop an automated energy distribution and reliability system. The purpose of this project was to implement a database-driven GIS solution that would manage all of the company's gas, electric, and landbase objects.

Buche, D. L.; Perry, S.

2007-10-01T23:59:59.000Z

127

Operational test report integrated system test (ventilation upgrade)  

Science Conference Proceedings (OSTI)

Operational Final Test Report for Integrated Systems, Project W-030 (Phase 2 test, RECIRC and HIGH-HEAT Modes). Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks, including upgraded vapor space cooling and filtered venting of tanks AY101, Ay102, AZ101, AZ102.

HARTY, W.M.

1999-10-05T23:59:59.000Z

128

Road Transportable Analytical Laboratory (RTAL) system: Volume I. Final report  

Science Conference Proceedings (OSTI)

This report describes a portable laboratory system for the analysis of soils, ground water, and surface waters for the detection and quantification of hazardous materials, organics, and radioactive contaminants. The goal of the Road Transportable Analytical Laboratory (RTAL) is a sample throughput of 20 samples per day, providing a full range of analysis on each sample within 16 hours of preparation with high accuracy.

Finger, S.M.; De Avila, J.C.; Keith, V.F.

1996-08-01T23:59:59.000Z

129

Utility battery storage systems. Program report for FY95  

DOE Green Energy (OSTI)

Sandia National Laboratories, New Mexico, conducts the Utility Battery Storage Systems Program, which is sponsored by the U.S. Department of Energy`s Office of Utility Technologies. The goal of this program is to assist industry in developing cost-effective battery systems as a utility resource option by 2000. Sandia is responsible for the engineering analyses, contracted development, and testing of rechargeable batteries and systems for utility energy storage applications. This report details the technical achievements realized during fiscal year 1995.

Butler, P.C.

1996-03-01T23:59:59.000Z

130

Energy storage systems program report for FY97  

DOE Green Energy (OSTI)

Sandia National Laboratories, New Mexico, conducts the Energy Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Utility Technologies. The goal of this program is to collaborate with industry in developing cost-effective electric energy storage systems for many high-value stationary applications. Sandia National Laboratories is responsible for the engineering analyses, contracted development, and testing of energy storage components and systems. This report details the technical achievements realized during fiscal year 1997. 46 figs., 20 tabs.

Butler, P.C.

1998-08-01T23:59:59.000Z

131

Federal Energy Management Program: EISA Compliance Tracking System Reports  

NLE Websites -- All DOE Office Websites (Extended Search)

EISA Compliance Tracking System Reports and Data EISA Compliance Tracking System Reports and Data EISA 432 Overview EISA requires Federal agencies to identify "covered facilities" that constitute at least 75% of their total facility energy use as subject to the requirements of the statute. Each Federal agency must designate an energy manager responsible for implementing the requirements at each covered facility. Comprehensive energy and water evaluations are to be performed at each covered facility every four years to identify potential energy and water efficiency and conservation measures. EISA requires agencies to report progress toward these requirements in CTS, along with: Estimated cost and savings for projects implemented in covered facilities Measured savings for implemented projects

132

Simulated coal gas MCFC power plant system verification. Final report  

DOE Green Energy (OSTI)

The objective of the main project is to identify the current developmental status of MCFC systems and address those technical issues that need to be resolved to move the technology from its current status to the demonstration stage in the shortest possible time. The specific objectives are separated into five major tasks as follows: Stack research; Power plant development; Test facilities development; Manufacturing facilities development; and Commercialization. This Final Report discusses the M-C power Corporation effort which is part of a general program for the development of commercial MCFC systems. This final report covers the entire subject of the Unocal 250-cell stack. Certain project activities have been funded by organizations other than DOE and are included in this report to provide a comprehensive overview of the work accomplished.

NONE

1998-07-30T23:59:59.000Z

133

TITLE III EVALUATION REPORT FOR THE SUBSURFACE LIGHTING SYSTEM  

SciTech Connect

The objective of this evaluation is to provide recommendations to ensure consistency between the technical baseline requirements, baseline design, and the as-constructed Subsurface Lighting System. Recommendations for resolving discrepancies between the as-constructed system, and the technical baseline requirements are included in this report. Cost and Schedule estimates are provided for all recommended modifications. This report does not address items which do not meet current safety or code requirements. These items are identified to the CMO and immediate action is taken to correct the situation. The report does identify safety and code items for which the A/E is recommending improvements. The recommended improvements will exceed the minimum requirements of applicable code and safety guide lines. These recommendations are intended to improve and enhance the operation and maintenance of the facility.

L.J. Fernandez

1998-09-09T23:59:59.000Z

134

Design review report for the SY-101 RAPID mitigation system  

Science Conference Proceedings (OSTI)

This report documents design reviews conducted of the SY-101 Respond And Pump In Days (RAPID) Mitigation System. As part of the SY-101 Surface-Level-Rise Remediation Project, the SY-101 WID Mitigation System will reduce the potential unacceptable consequences of crust growth in Tank 241-SY-101 (SY-101). Projections of the crust growth rate indicate that the waste level in the tank may reach the juncture of the primary and secondary confinement structures of the tank late in 1999. Because of this time constraint, many design activities are being conducted in parallel and design reviews were conducted for system adequacy as well as design implementation throughout the process. Design implementation, as used in this design review report, is the final component selection (e.g., which circuit breaker, valve, or thermocouple) that meets the approved design requirements, system design, and design and procurement specifications. Design implementation includes the necessary analysis, testing, verification, and qualification to demonstrate compliance with the system design and design requirements. Design implementation is outside the scope of this design review. The design activities performed prior to detailed design implementation (i.e., system mission requirements, functional design requirements, technical criteria, system conceptual design, and where design and build contracts were placed, the procurement specification) have been reviewed and are within the scope of this design review report. Detailed design implementation will be controlled, reviewed, and where appropriate, approved in accordance with Tank Waste Remediation System (TWRS) engineering procedures. Review of detailed design implementation will continue until all components necessary to perform the transfer function are installed and tested.

SCHLOSSER, R.L.

1999-05-24T23:59:59.000Z

135

Searching the Occurrence Reporting and Processing Systems (ORPS) database  

Science Conference Proceedings (OSTI)

The Occurrence Reporting and Processing System (ORPS) is a computerized method to submit, collect, update, and sign occurrence reports required by US Department of Energy (DOE) Order 5000.3B, Occurrence Reporting and Processing of Operations Information. The basic reason for investigating and reporting the causes of occurrences is to enable the identification of corrective actions to prevent recurrence and, thereby, protect the health and safety of the public, the workers, and the environment. ORPS provides the DOE community with a readily accessible database that contains information about occurrences at DOE facilities, causes of those occurrences, and corrective actions. This information can, therefore, be used to identify and analyze trends in occurrences. The ORPS database resides on a host computer located at the Idaho National Engineering Laboratory (INEL) in Idaho Falls, Idaho. The database can be accessed from any DOE site via computer terminals or personal computers (PCs) that are set up to access ORPS.

Commander, S.L.

1992-11-01T23:59:59.000Z

136

Test report : Raytheon / KTech RK30 energy storage system.  

SciTech Connect

The Department of Energy Office of Electricity (DOE/OE), Sandia National Laboratories (SNL) and the Base Camp Integration Lab (BCIL) partnered together to incorporate an energy storage system into a microgrid configured Forward Operating Base to reduce the fossil fuel consumption and to ultimately save lives. Energy storage vendors will be sending their systems to SNL Energy Storage Test Pad (ESTP) for functional testing and then to the BCIL for performance evaluation. The technologies that will be tested are electro-chemical energy storage systems comprising of lead acid, lithium-ion or zinc-bromide. Raytheon/KTech has developed an energy storage system that utilizes zinc-bromide flow batteries to save fuel on a military microgrid. This report contains the testing results and some limited analysis of performance of the Raytheon/KTech Zinc-Bromide Energy Storage System.

Rose, David Martin; Schenkman, Benjamin L.; Borneo, Daniel R.

2013-10-01T23:59:59.000Z

137

Standards for photovoltaic energy conversion systems. Final report  

DOE Green Energy (OSTI)

This report provides the results of a search for existing domestic standards and related documents for possible application in the development of a standards base for photovoltaic energy conversion systems. The search resulted in locating about 150 test methods, recommended practices, standards, solar-thermal performance criteria, and other standards-related documents. They are listed by topic areas in the appendix. The listing was prepared to assist those involved in developing performance criteria for photovoltaic systems and in identifying methods to test system performance against these criteria. It is clear from the results of the search that few standards are directly applicable to terrestrial solar photovoltaic systems and that much standards development is required to support the commercialization of such systems.

Schafft, H. A.

1980-04-01T23:59:59.000Z

138

Variable-Speed Wind System Design : Final Report.  

SciTech Connect

Almost from the onset of the development of wind energy conversion systems (WECS), it was known that variable-speed operation of the turbine would maximize energy capture. This study was commissioned to assess the cost, efficiency gain, reduction of the cost of energy (COE), and other operating implications of converting the existing hardware of a modern fixed-speed wind energy conversion system to variable-speed operation. The purpose of this study was to develop a preliminary design for the hardware required to allow variable-speed operation using a doubly-fed generator with an existing fixed-speed wind turbine design. The turbine selected for this study is the AWT-26 designed and built by Advanced Wind Turbines Inc. of Redmond, Washington. The lowest projected COE using this variable-speed generation system is projected to be $0.0499/kWh, compared to the lowest possible COE with fixed-speed generation which is projected to be $0.0546/kWh. This translates into a 8.6% reduction of the COE using this variable-speed generation option. The preliminary system design has advanced to where the printed circuit boards can be physically laid out based on the schematics and the system software can be written based on the control flow-charts. The core of hardware and software has been proven to be successful in earlier versions of VSG systems. The body of this report presents the results of the VSWG system development. Operation under normal and fault conditions is described in detail, the system performance for variable-speed operation is estimated and compared to the original fixed-speed system performance, and specifications for all system components (generator, power electronic converter, and system controller) are given. Costs for all components are estimated, and incremental system cost is compared to incremental energy production. Finally, operational features of the VSWG which are not available in the existing FSWG system are outlined.

Lauw, Hinan K.; Weigand, Claus H.; Marckx, Dallas A.; Electronic Power Conditioning, Inc.

1993-10-01T23:59:59.000Z

139

Operational test report -- Project W-320 cathodic protection systems  

Science Conference Proceedings (OSTI)

Washington Administrative Code (WAC) 173-303-640 specifies that corrosion protection must be designed into tank systems that treat or store dangerous wastes. Project W-320, Waste Retrieval Sluicing System (WRSS), utilizes underground encased waste transfer piping between tanks 241-C-106 and 241-AY-102. Corrosion protection is afforded to the encasements of the WRSS waste transfer piping through the application of earthen ionic currents onto the surface of the piping encasements. Cathodic protection is used in conjunction with the protective coatings that are applied upon the WRSS encasement piping. WRSS installed two new two rectifier systems (46 and 47) and modified one rectifier system (31). WAC 173-303-640 specifies that the proper operation of cathodic protection systems must be confirmed within six months after initial installation. The WRSS cathodic protection systems were energized to begin continuous operation on 5/5/98. Sixteen days after the initial steady-state start-up of the WRSS rectifier systems, the operational testing was accomplished with procedure OTP-320-006 Rev/Mod A-0. This operational test report documents the OTP-320-006 results and documents the results of configuration testing of integrated piping and rectifier systems associated with the W-320 cathodic protection systems.

Bowman, T.J.

1998-06-16T23:59:59.000Z

140

Communications and control for electric power systems: Final report  

Science Conference Proceedings (OSTI)

This report is a summary of some of the work done on the Communications and Control project, with particular emphasis on the achievements during the years 1986--1996. During those years, the project moved away from concern with dispersed storage and generation and its impact on power system operation (the team was responsible for studies in this area, and for making a power system simulator that included DSG), and became involved in more concrete work aimed at applying high-tech solutions to problems of power system communications and control. This report covers work done at JPL on the following topics: (1) the measurement of electric and magnetic fields, both ac and dc; (2) the use of optical power to supply low-power electronics; (3) the design of a fault-tolerant communication system designed for distribution automation; and (4) a digital phase locked loop that allows the use of low-power transmitting electronics to recreate a good-quality signal at the receiver. In a report of this kind, only the results and highlights of the work are described.

Kirkham, H.

1998-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Dynamic Systems Analysis Report for Nuclear Fuel Recycle  

SciTech Connect

This report examines the time-dependent dynamics of transitioning from the current United States (U.S.) nuclear fuel cycle where used nuclear fuel is disposed in a repository to a closed fuel cycle where the used fuel is recycled and only fission products and waste are disposed. The report is intended to help inform policy developers, decision makers, and program managers of system-level options and constraints as they guide the formulation and implementation of advanced fuel cycle development and demonstration efforts and move toward deployment of nuclear fuel recycling infrastructure.

Brent Dixon; Sonny Kim; David Shropshire; Steven Piet; Gretchen Matthern; Bill Halsey

2008-12-01T23:59:59.000Z

142

Building America Systems Integration Research Annual Report: FY 2012  

SciTech Connect

This document is the Building America FY2012 Annual Report, which includes an overview of the Building America Program activities and the work completed by the National Renewable Energy Laboratory and the Building America industry consortia (the Building America teams). The annual report summarizes major technical accomplishments and progress towards U.S. Department of Energy Building Technologies Program's multi-year goal of developing the systems innovations that enable risk-free, cost effective, reliable and durable efficiency solutions that reduce energy use by 30%-50% in both new and existing homes.

Gestwick, M.

2013-05-01T23:59:59.000Z

143

Building America Systems Integration Research Annual Report: FY 2012  

SciTech Connect

This document is the Building America FY2012 Annual Report, which includes an overview of the Building America Program activities and the work completed by the National Renewable Energy Laboratory and the Building America industry consortia (the Building America teams). The annual report summarizes major technical accomplishments and progress towards U.S. Department of Energy Building Technologies Program's multi-year goal of developing the systems innovations that enable risk-free, cost effective, reliable and durable efficiency solutions that reduce energy use by 30%-50% in both new and existing homes.

Gestwick, M.

2013-05-01T23:59:59.000Z

144

Enhanced Geothermal Systems (EGS) R&D Program, Status Report: Foreign Research on Enhanced Geothermal Systems  

DOE Green Energy (OSTI)

This report reviews enhanced geothermal systems (EGS) research outside the United States. The term ''enhanced geothermal systems'' refers to the use of advanced technology to extract heat energy from underground in areas with higher than average heat flow but where the natural permeability or fluid content is limited. EGS covers the spectrum of geothermal resources from low permeability hydrothermal to hot dry rock.

McLarty, Lynn; Entingh, Daniel

2000-09-29T23:59:59.000Z

145

Small power systems study. Volume. Study results. Technical summary report  

DOE Green Energy (OSTI)

The Division of Solar Technology of the Department of Energy is currently examining the market potential of a number of dispersed solar energy systems, including the small (less than or equal to 10 MW/sub e/) solar thermal power system. Small fossil-fueled generating units in the United States utility system, (i.e., investor-owned, municipal, and cooperatives) have a current capacity of approximately 8000 MW/sub e/ or about 1.5 percent of the total US electrical capacity, and provide a large potential market for small solar thermal power systems. The Small Power Systems Study has as its objective the determination of conditions under which small (less than or equal to 10 MW/sub e/) solar thermal power units can provide cost-effective electrical power to a variety of users. Potential users, in addition to the utility systems; include Department of Defense installations and applications, remote mining and/or lumbering operations, and other industrial power systems with and without cogeneration. The first year's results on the Small Power Systems Study are summarized. The data base used and the breakeven cost analysis are discussed. Information on both small (less than or equal to 10 MW/sub e/) generating units and the utility systems using them is presented as well as data on fossil fuel costs, solar plant costs, and solar insolation values. The results of a survey of Department of Defense (DOD) worldwide electrical generating capacity at its military bases and on a potential DOD application are presented. Information on a potential small solar power system experiment in the interior of Alaska is given, and a limited amount of information on a remote application which would provide power or a large open pit copper mine is presented. Volume II of this Technical Summary Report contains an inventory, by state, of the small (less than or equal to 10 MW/sub e/) generating units in the US utility system. (WHK)

Sitney, L.R.

1978-05-31T23:59:59.000Z

146

Small power systems study. Volume. Study results. Technical summary report  

SciTech Connect

The Division of Solar Technology of the Department of Energy is currently examining the market potential of a number of dispersed solar energy systems, including the small (less than or equal to 10 MW/sub e/) solar thermal power system. Small fossil-fueled generating units in the United States utility system, (i.e., investor-owned, municipal, and cooperatives) have a current capacity of approximately 8000 MW/sub e/ or about 1.5 percent of the total US electrical capacity, and provide a large potential market for small solar thermal power systems. The Small Power Systems Study has as its objective the determination of conditions under which small (less than or equal to 10 MW/sub e/) solar thermal power units can provide cost-effective electrical power to a variety of users. Potential users, in addition to the utility systems; include Department of Defense installations and applications, remote mining and/or lumbering operations, and other industrial power systems with and without cogeneration. The first year's results on the Small Power Systems Study are summarized. The data base used and the breakeven cost analysis are discussed. Information on both small (less than or equal to 10 MW/sub e/) generating units and the utility systems using them is presented as well as data on fossil fuel costs, solar plant costs, and solar insolation values. The results of a survey of Department of Defense (DOD) worldwide electrical generating capacity at its military bases and on a potential DOD application are presented. Information on a potential small solar power system experiment in the interior of Alaska is given, and a limited amount of information on a remote application which would provide power or a large open pit copper mine is presented. Volume II of this Technical Summary Report contains an inventory, by state, of the small (less than or equal to 10 MW/sub e/) generating units in the US utility system. (WHK)

Sitney, L.R.

1978-05-31T23:59:59.000Z

147

Environmental Systems Research Candidates FY-01 Annual Report  

Science Conference Proceedings (OSTI)

The Environmental Systems Research Candidates (ESRC) Program ran from April 2000 through September 2001 as part of the Environmental Systems Research and Analysis (ESRA) Program at the Idaho National Engineering and Environmental Laboratory (INEEL). ESRA provides key science and technology to meet the cleanup mission of the U.S. Department of Energy Office of Environmental Management (EM), and performs research and development that will help solve current legacy problems and enhance the INEELs scientific and technical capability for solving longer-term challenges. This report documents the accomplishments of the ESRC Program. The ESRC Program consisted of 25 tasks subdivided within four research areas.

Miller, David Lynn; Piet, Steven James

2001-03-01T23:59:59.000Z

148

Hydrogen Deployment System Modeling Environment (HyDS ME) Documentation: Milestone Report FY 2006  

DOE Green Energy (OSTI)

This report introduces the Hydrogen Deployment System Modeling Environment model, assumptions, and basic operations.

Parks. K.

2006-11-01T23:59:59.000Z

149

Ocean energy systems. Quarterly report, January-March 1983  

DOE Green Energy (OSTI)

Progress is reported on the development of Ocean Thermal Energy Conversion (OTEC) systems that will provide synthetic fuels (e.g., methanol), energy-intensive products such as ammonia (for fertilizers and chemicals), and aluminum. The work also includes assessment and design concepts for hybrid plants, such as geothermal-OTEC (GEOTEC) plants. Another effort that began in the spring of 1982 is a technical advisory role to DOE with respect to their management of the conceptual and preliminary design activity of industry teams that are designing a shelf-mounted offshore OTEC pilot plant that could deliver power to Oahu, Hawaii. In addition, a program is underway to evaluate and test the Pneumatic Wave-Energy Conversion System (PWECS), an ocean-energy device consisting of a turbine that is air-driven as a result of wave action in a chamber. This Quarterly Report summarizes the work on the various tasks as of 31 March 1983.

Not Available

1983-03-30T23:59:59.000Z

150

Short-Termed Integrated Forecasting System: 1993 Model documentation report  

Science Conference Proceedings (OSTI)

The purpose of this report is to define the Short-Term Integrated Forecasting System (STIFS) and describe its basic properties. The Energy Information Administration (EIA) of the US Energy Department (DOE) developed the STIFS model to generate short-term (up to 8 quarters), monthly forecasts of US supplies, demands, imports exports, stocks, and prices of various forms of energy. The models that constitute STIFS generate forecasts for a wide range of possible scenarios, including the following ones done routinely on a quarterly basis: A base (mid) world oil price and medium economic growth. A low world oil price and high economic growth. A high world oil price and low economic growth. This report is written for persons who want to know how short-term energy markets forecasts are produced by EIA. The report is intended as a reference document for model analysts, users, and the public.

Not Available

1993-05-01T23:59:59.000Z

151

Solar thermal power systems. Annual technical progress report, FY 1978  

DOE Green Energy (OSTI)

A technical progress report on the DOE Solar Thermal Power Systems Program is given. Emphasis is on the technical progress of the projects rather than on activities and individual contractor efforts. Each project description indicates its place in the prior to FY 1978 is given; the significant achievements and real progress of each project during FY 1978 are described; and future project activities as well as anticipated significant achievements for each project are forecast. (WHK)

Not Available

1979-06-01T23:59:59.000Z

152

Safety analysis report for packaging (onsite) sample pig transport system  

Science Conference Proceedings (OSTI)

This Safety Analysis Report for Packaging (SARP) provides a technical evaluation of the Sample Pig Transport System as compared to the requirements of the U.S. Department of Energy, Richland Operations Office (RL) Order 5480.1, Change 1, Chapter III. The evaluation concludes that the package is acceptable for the onsite transport of Type B, fissile excepted radioactive materials when used in accordance with this document.

MCCOY, J.C.

1999-03-16T23:59:59.000Z

153

Development of geothermal-well-completion systems. Final report  

DOE Green Energy (OSTI)

Results of a three year study concerning the completion of geothermal wells, specifically cementing, are reported. The research involved some specific tasks: (1) determination of properties an adequate geothermal well cement must possess; (2) thorough evaluation of current high temperature oilwell cementing technology in a geothermal context; (3) basic research concerning the chemical and physical behavior of cements in a geothermal environment; (4) recommendation of specific cement systems suitable for use in a geothermal well.

Nelson, E.B.

1979-01-01T23:59:59.000Z

154

Thermal power systems: Small Power Systems Applications Project. Volume II. Detailed report. Annual technical report, fiscal year 1978  

SciTech Connect

Small Power Systems Applications activities for FY 1978 are reported. Studies were conducted to address current small power system technology as applied to power plants up to 10 MWe in size. Markets for small power systems were characterized and cost goals were established for the project. Candidate power plant system design concepts were selected for evaluation and preliminary performance and cost assessments were made. Economic studies were conducted at JPL and under contract to Burns and McDonnell. Breakeven capital costs were determined for leading contenders among the candidate systems. An applications study was made of the potential use of small power systems in providing part of the demand for pumping power by the extensive aqueduct system of California, estimated to be 1000 MWe by 1985. Criteria and methodologies were developed for application to the ranking of candidate power plant system design concepts. Experimental power plants concepts of 1 MWe rating were studied by three contractors as a Phase I effort leading toward the definition of a power plant configuration for subsequent detail design, construction, testing and evaluation as Engineering Experiment No. 1 (EE No. 1). Site selection criteria and ground rules for the solicitation of EE No. 1 site participation proposals by DOE were developed.

1979-01-15T23:59:59.000Z

155

Conceptual design and systems analysis of photovoltaic systems. Volume II. Study results. Final report  

DOE Green Energy (OSTI)

This investigation of terrestrial PV systems considered the technical and economic feasibility for systems in three size categories: a small system of about 12 kW peak output for on-site residential use; a large 1500 MW central power plant contributing to the bulk energy of a utility system power grid; and an intermediate size system of about 250 kW for use on public or commercial buildings. In each category, conceptual designs were developed, performance was analyzed for a range of climatic regions, economic analyses were performed, and assessments were made of pertinent institutional issues. The report consists of three volumes. Volume I contains a Study Summary of the major study results. This volume contains the detailed results pertaining to on-site residential photovoltaic systems, central power plant photovoltaic systems, and intermediate size systems applied to commercial and public buildings. Volume III contains supporting appendix material. (WHK)

Kirpich, A.

1977-03-19T23:59:59.000Z

156

HyPEP FY-07 Report: System Integration Model Development  

DOE Green Energy (OSTI)

The integrated system of a Very High Temperature Gas-Cooled Reactor (VHTR) and a High Temperature Steam Electrolysis (HTSE) process is one of systems being investigated by the U.S. Department of Energy and Idaho National Laboratory. This system will produce hydrogen by utilizing a highly efficient VHTR with an outlet temperature of 900 C and supplying necessary energy and electricity to the HTSE process for electrolysis of high temperature steam. This report includes a description of five configurations including an indirect parallel cycle, an indirect serial cycle, a direct serial cycle, a steam combined cycle, and a reheat cycle. HYSYS simulations were performed for each of these configurations coupled to a HTSE process. Final results are presented along with parametric studies and process optimization.

C. H. Oh; E. S. Kim; S. R. Sherman; R. Vilim

2007-04-01T23:59:59.000Z

157

Report to Congress: Comprehensive Program Plan for Advanced Turbine Systems  

DOE Green Energy (OSTI)

Consistent with the Department of Energy (DOE) mission, the Advanced Turbine Systems (ATS) Program will develop more efficient gas turbine systems for both utility and industrial electric power generation (including cogeneration). The Program will develop base-load power systems for commercial offering in the year 2000. Although the target fuel is natural gas, the ATS will be adaptable to coal and biomass firing. All ATS will exhibit these characteristics: Ultra-high efficiency [utility systems: 60 percent (lower heating value basis); industrial systems: 15 percent improvement over today`s best gas turbine systems]; Environmental superiority [reduced nitrogen oxides (NO{sub x}), carbon dioxide (CO{sub 2}), carbon monoxide (CO), and unburned hydrocarbons (UHC)]; and Cost competitiveness [10 percent lower cost of electricity]. This Program Plan was requested in the House, Senate, and Conference Reports on the FY 1993 Interior and Related Agencies Appropriations Act, Public Law 102--381, and is consistent with the Energy Policy Act of 1992, which (in Section 2112) identifies work for improving gas turbines. This plan outlines the 8-year ATS Program and discusses rationale and planning. Total Program costs are estimated to be $700 million, consisting of an approximate $450 million government share and an approximate $250 million cost-share by industrial participants.

Not Available

1993-07-01T23:59:59.000Z

158

Search Hanford accessible reports electronically system requirements specification  

SciTech Connect

The Emergency, Safety, & Quality (ESQ) Services organization of Westinghouse Hanford Company (WHC) is experiencing changes related to new programs. The programs include Corrective Actions Management Systems, Self-Assessment, Trend Analysis, and Lessons Learned analysis. The programs are pushing up organizational costs while funding and manpower levels are projected to be dropping. A large cost involved in implementing the new programs is the cost for people to locate unstructured information required to make decisions or write documentation. But, most resources for retrieving information are found in structured database systems. This means that unstructured information that must be located has to be found by one of these methods: (1) searching manually through documents, (2) searching individual documents one at a time with word processing programs, (3) searching through text fields with query systems primarily designed for structured database information, or (4) develop a text search and retrieval system designed for unstructured information. One example of this is using Occurrence Reporting Processing System (ORPS) and Quality, Environmental, and Safety Tracking (QUEST) documents. An explanation of this is in the following textual box.

Willers, K.J.

1994-02-28T23:59:59.000Z

159

Power systems development facility. Quarterly report, January 1995--March 1995  

Science Conference Proceedings (OSTI)

The objective of this project is to evaluate hot gas particle control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scale-up of particulate control systems to commercial size. The conceptual design of the facility was extended to include a within scope, phased expansion of the existing Hot Gas Cleanup Test Facility Cooperative Agreement to also address systems integration issues of hot particulate removal in advanced coal-based power generation systems. This expansion included the consideration of the following modules at the test facility in addition to the original Transport Reactor gas source and Hot Gas Cleanup Units: (1) Carbonizer/Pressurized Circulating Fluidized Bed Gas Source. (2) Hot Gas Cleanup Units to mate to all gas streams. (3) Combustion Gas Turbine. (4) Fuel Cell and associated gas treatment. This expansion to the Hot Gas Cleanup Test Facility is herein referred to as the Power Systems Development Facility (PSDF). The major emphasis during this reporting period was continuing the detailed design of the facility and integrating the particulate control devices (PCDs) into structural and process designs.

NONE

1995-05-01T23:59:59.000Z

160

Ocean energy systems. Quarterly report, October-December 1982  

DOE Green Energy (OSTI)

Research progress is reported on developing Ocean Thermal Energy Conversion (OTEC) systems that will provide synthetic fuels (e.g., methanol), energy-intensive products such as ammonia (for fertilizers and chemicals), and aluminum. The work also includes assessment and design concepts for hybrid plants, such as geothermal-OTEC (GEOTEC) plants. Another effort that began in the spring of 1982 is a technical advisory role to DOE with respect to their management of the conceptual design activity of the two industry teams that are designing offshore OTEC pilot plants that could deliver power to Oahu, Hawaii. In addition, a program is underway in which tests of a different kind of ocean-energy device, a turbine that is air-driven as a result of wave action in a chamber, are being planned. This Quarterly Report summarizes the work on the various tasks as of 31 December 1982.

Not Available

1982-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Conceptual design and systems analysis of photovoltaic power systems. Volume II. Systems. Revised final report  

DOE Green Energy (OSTI)

Conceptual designs were made and analyses were performed on three types of solar photovoltaic power systems. Included were Residential (1--10 kW), Intermediate (0.1--10 MW), and Central (50--1000 MW) Power Systems to be installed in the 1985 to 2000 time period. Detailed descriptions of each of the three systems studied, descriptions of the necessary subsystems, and discussions of the interfaces between them are presented. Included also are descriptions of system performance and system cost used to perform an economic analysis which assesses the value of each system.

Pittman, P.F.

1977-03-01T23:59:59.000Z

162

MARKET-BASED ADVANCED COAL POWER SYSTEMS FINAL REPORT  

NLE Websites -- All DOE Office Websites (Extended Search)

MARKET-BASED ADVANCED MARKET-BASED ADVANCED COAL POWER SYSTEMS FINAL REPORT MAY 1999 DOE/FE-0400 U.S. Department of Energy Office of Fossil Energy Washington, DC 20585 Market-Based Advanced Coal Power Systems 1-1 December 1998 1. INTRODUCTION As deregulation unfolds and privatization of the utility market takes shape, priorities for power plant economics have shifted toward those of a "bottom-line" business and away from a regulated industry. Competition in utility generation and the exposure risks of large capital investments have led to a preference to minimize capital costs and fixed and variable operation and maintenance costs. With global competition from independent power producers (IPPs), non- utility generators, and utilities, the present trend of investments is with conventional pulverized

163

Integrated thermal treatment systems study. Internal review panel report  

SciTech Connect

The U.S. Department of Energy (DOE) Office of Technology Development (OTD) commissioned two studies to evaluate nineteen thermal treatment technologies for treatment of DOE mixed low-level waste. These studies were called the Integrated Thermal Treatment System (ITTS) Phase I and Phase II. With the help of the DOE Office of Environmental Management (EM) Mixed Waste Focus Group, OTD formed an ITTS Internal Review Panel to review and comment on the ITTS studies. This Panel was composed of scientists and engineers from throughout the DOE complex, the U.S. Environmental Protection Agency, the California EPA, and private experts. The Panel met from November 15-18, 1994 to review the ITTS studies and to make recommendations on the most promising thermal treatment systems for DOE mixed low-level wastes and on research and development necessary to prove the performance of the technologies. This report describes the findings and presents the recommendations of the Panel.

Cudahy, J.; Escarda, T.; Gimpel, R. [and others

1995-04-01T23:59:59.000Z

164

DOE technology information management system database study report  

SciTech Connect

To support the missions of the US Department of Energy (DOE) Special Technologies Program, Argonne National Laboratory is defining the requirements for an automated software system that will search electronic databases on technology. This report examines the work done and results to date. Argonne studied existing commercial and government sources of technology databases in five general areas: on-line services, patent database sources, government sources, aerospace technology sources, and general technology sources. First, it conducted a preliminary investigation of these sources to obtain information on the content, cost, frequency of updates, and other aspects of their databases. The Laboratory then performed detailed examinations of at least one source in each area. On this basis, Argonne recommended which databases should be incorporated in DOE`s Technology Information Management System.

Widing, M.A.; Blodgett, D.W.; Braun, M.D.; Jusko, M.J.; Keisler, J.M.; Love, R.J.; Robinson, G.L. [Argonne National Lab., IL (United States). Decision and Information Sciences Div.

1994-11-01T23:59:59.000Z

165

An Update of Dermatologist Usage of the Physician Quality Reporting System in Colorado for 2011  

E-Print Network (OSTI)

Reporting Initiatives in Colorado. Journal of the AmericanQuality Reporting System in Colorado for 2011 Jeffrey H.of Dermatology, University of Colorado Denver, Aurora, CO

Dunn, Jeffrey H; Alvarez, Bryan T; Dellavalle, Robert P; Dunnick, Cory A

2013-01-01T23:59:59.000Z

166

Development report: automatic system test and calibration (ASTAC) equipment  

DOE Green Energy (OSTI)

The Automatic System Test and Calibration (ASTAC) Equipment has been developed by Paragon Pacific, Inc. to be used in conjunction with the NASA Lewis Research Center Wind Energy System Time-Domain (WEST) Analyzer. ASTAC is used to monitor the performance of the WEST Analyzer and to identify component malfunctions which may occur from time to time within WEST. The heart of the ASTAC system is a microcomputer which is used to input prescribed test signals into all WEST subsystems via a hybrid interface unit, and to process WEST output responses to these test signals. Measured responses are compared to theoretical levels calculated off-line using specialized ASTAC software. This report describes the microcomputer, the interface unit and the software packages which in total comprise the ASTAC system. Examples of ASTAC test results obtained on the WEST Analyzer are presented and described in detail. In addition, a section has been included which briefly describes the methods by which the microcomputer and interface unit can be maintained.

Thoren, R.J.

1981-07-01T23:59:59.000Z

167

Field demonstrations of communication systems for distribution automation. Final report  

Science Conference Proceedings (OSTI)

This report summarizes the results of a field demonstration of the use of UHF radio links in the 950-MHz portion of the spectrum as a communication medium for performing automated electric power distribution. Prototype radiohardware was combined with logic and control equipment developed by Westinghouse for power-line carrier automated distribution systems. Transceivers were used in the remote interactive terminals. 3dbm transceivers were used in the Central Base Station and the three Primary Radio Terminals, which functioned as system repeaters. Pre-installation field-strength measurements were made along selected radials and in spot locations to characterize the anticipated field-strength contours that would be encountered during the operational testing. A propagation model was developed that accurately predicted the conditions actually recorded. Post-installation measurements were used to further calibrate the computer model. The resulting propagation analysis proved exceedingly effective in characterizing a UHF radio system for digital communication. Data collected during a 10-month operational period supports the conclusion that 950-MHz radio is a viable communications medium for performing utility automated distribution functions. The system consists of 250 remote terminals, each interrogated from three sites. This provides 750 paths for communication performance evaluation.The reliability of the prototype radio units used in this project fell below that predicted through MTBF analysis, and did not meet utility reliability standards. The logic and control circuitry and central station required very little maintenance during the test.

Not Available

1981-06-01T23:59:59.000Z

168

Fluid dynamics of double diffusive systems. Final report  

SciTech Connect

Over the past seven years the authors have conducted an experimental, numerical, and theoretical study of the stability of doubly diffusive systems, and of mixing processes in stratified turbulence. For the study of the stability of doubly diffusive systems continuous gradients of two diffusing components (heat and salinity in this case) were used as the initial condition, and forcing was introduced by lateral heating and surface shear. The goals of this work included (1) quantification of the effects of finite amplitude disturbances on stable, double diffusive systems, particularly with respect to lateral heating, (2) development of an improved understanding of the physical phenomena present in sheardriven flows in doubly diffusive stratified environments, (3) increasing their knowledge-base on turbulent flow in stratified environments and how to represent it, and (4) formulation of a numerical code for such flows. In particular, the overall goals of this aspect of the research were as follows: (1) develop more general stability and scaling criteria for the destabilization of doubly-stratified systems, (2) study the variation of flow structure and scales with Rayleigh ratio and lateral heating ratio, (3) delineate the mechanisms governing convective layer formation and merging, (4) study the mixing processes within the convective layers and across interfaces, and estimate the heat and mass fluxes in such a system, (5) quantify the effects of turbulence and coherent structures (due to a wind-driven surface shear) on a doubly stratified system, and (6) study the interaction between surface shear and side-wall heating destabilization mechanisms. Goals 1 through 4 have been successfully completed and the results are described in this report.

Koseff, J.R.

1995-07-01T23:59:59.000Z

169

Environmental Systems Research and Analysis FY 2000 Annual Report  

SciTech Connect

The Environmental Systems Research (ESR) Program, a part of the Environmental Systems Research and Analysis (ESRA) Program, was implemented to enhance and augment the technical capabilities of the INEEL. Strengthening the Technical capabilities of the INEEL will provide the technical base to serve effectively as the Environmental Management Laboratory for the Office of Environmental Management (EM). This is a progress report for the third year of the ESR Program (FY 2000). A report of activities is presented for the five ESR research investment areas: (1) Transport Aspects of Selective Mass Transport Agents, (2) Chemistry of Environmental Surfaces, (3) Materials Dynamics, (4) Characterization Science, and (5) Computational Simulation of Mechanical and Chemical Systems. In addition to the five technical areas, the report describes activities in the Science and Technology Foundations element of the program, e.g., interfaces between ESR and the EM Science Program (EMSP) and the EM Focus Areas. The five research areas are subdivided into 18 research projects. FY 2000 research in these 18 projects has resulted in more than 50 technical papers that are in print, in press, in review, or in preparation. Additionally, more than 100 presentations were made at professional society meetings nationally and internationally. Work supported by this program was in part responsible for one of our researchers, Dr. Mason Harrup, receiving the Department of Energys Bright Light and Energy at 23 awards. Significant accomplishments were achieved. Non-Destructive Assay hardware and software was deployed at the INEEL, enhancing the quality and efficiency of TRU waste characterization for shipment. The advanced tensiometer has been employed at numerous sites around the complex to determine hydrologic gradients in variably saturated vadose zones. An ion trap, secondary ion mass spectrometer (IT-SIMS) was designed and fabricated to deploy at the INEEL site to measure the chemical speciation of radionuclides and toxic metals on the surfaces of environmentally significant minerals. The FY 2001 program will have a significantly different structure and research content. This report presents the final summary of projects coming to an end in FY 2000 and is a bridge to the FY 2001 program.

David L. Miller; Castle, Peter Myer; Steven J. Piet

2001-01-01T23:59:59.000Z

170

Commercial thermal distribution systems, Final report for CIEE/CEC  

Science Conference Proceedings (OSTI)

According to the California Energy Commission (CEC 1998a), California commercial buildings account for 35% of statewide electricity consumption, and 16% of statewide gas consumption. Space conditioning accounts for roughly 16,000 GWh of electricity and 800 million therms of natural gas annually, and the vast majority of this space conditioning energy passes through thermal distribution systems in these buildings. In addition, 8600 GWh per year is consumed by fans and pumps in commercial buildings, most of which is used to move the thermal energy through these systems. Research work at Lawrence Berkeley National Laboratory (LBNL) has been ongoing over the past five years to investigate the energy efficiency of these thermal distribution systems, and to explore possibilities for improving that energy efficiency. Based upon that work, annual savings estimates of 1 kWh/ft{sup 2} for light commercial buildings, and 1-2 kWh/ft{sup 2} in large commercial buildings have been developed for the particular aspects of thermal distribution system performance being addressed by this project. Those savings estimates, combined with a distribution of the building stock based upon an extensive stock characterization study (Modera et al. 1999a), and technical penetration estimates, translate into statewide saving potentials of 2000 GWh/year and 75 million thermal/year, as well as an electricity peak reduction potential of 0.7 GW. The overall goal of this research program is to provide new technology and application knowledge that will allow the design, construction, and energy services industries to reduce the energy waste associated with thermal distribution systems in California commercial buildings. The specific goals of the LBNL efforts over the past year were: (1) to advance the state of knowledge about system performance and energy losses in commercial-building thermal distribution systems; (2) to evaluate the potential of reducing thermal losses through duct sealing, duct insulation, and improved equipment sizing; and (3) to develop and evaluate innovative techniques applicable to large buildings for sealing ducts and encapsulating internal duct insulation. In the UCB fan project, the goals were: (1) to develop a protocol for testing, analyzing and diagnosing problems in large commercial building built-up air handling systems, and (2) to develop low-cost measurement techniques to improve short term monitoring practices. To meet our stated goals and objectives, this project: (1) continued to investigate and characterize the performance of thermal distribution systems in commercial buildings; (2) performed energy analyses and evaluation for duct-performance improvements for both small and large commercial buildings; (3) developed aerosol injection technologies for both duct sealing and liner encapsulation in commercial buildings; and (4) designed energy-related diagnostic protocols based on short term measurement and used a benchmarking database to compare subject systems with other measured systems for certain performance metrics. This year's efforts consisted of the following distinct tasks: performing characterization measurements for five light commercial building systems and five large-commercial-building systems; analyzing the potential for including duct performance in California's Energy Efficiency Standards for Residential and Non-Residential Buildings (Title 24), including performing energy and equipment sizing analyses of air distribution systems using DOE 2.1E for non-residential buildings; conducting laboratory experiments, field experiments, and modeling of new aerosol injection technologies concepts for sealing and coating, including field testing aerosol-based sealing in two large commercial buildings; improving low-cost fan monitoring techniques measurements, and disseminating fan tools by working with energy practitioners directly where possible and publishing the results of this research and the tools developed on a web-site. The final report consists of five sections listed below. Each section includes its related

Xu, Tengfang; Bechu, Olivier; Carrie, Remi; Dickerhoff, Darryl; Fisk, William; Franconi, Ellen; Kristiansen, Oyvind; Levinson, Ronnen; McWilliams, Jennifer; Wang, Duo; Modera, Mark; Webster, Tom; Ring, Erik; Zhang, Qiang; Huizenga, Charlie; Bauman, Fred; Arens, Ed

1999-12-01T23:59:59.000Z

171

Commercial thermal distribution systems, Final report for CIEE/CEC  

SciTech Connect

According to the California Energy Commission (CEC 1998a), California commercial buildings account for 35% of statewide electricity consumption, and 16% of statewide gas consumption. Space conditioning accounts for roughly 16,000 GWh of electricity and 800 million therms of natural gas annually, and the vast majority of this space conditioning energy passes through thermal distribution systems in these buildings. In addition, 8600 GWh per year is consumed by fans and pumps in commercial buildings, most of which is used to move the thermal energy through these systems. Research work at Lawrence Berkeley National Laboratory (LBNL) has been ongoing over the past five years to investigate the energy efficiency of these thermal distribution systems, and to explore possibilities for improving that energy efficiency. Based upon that work, annual savings estimates of 1 kWh/ft{sup 2} for light commercial buildings, and 1-2 kWh/ft{sup 2} in large commercial buildings have been developed for the particular aspects of thermal distribution system performance being addressed by this project. Those savings estimates, combined with a distribution of the building stock based upon an extensive stock characterization study (Modera et al. 1999a), and technical penetration estimates, translate into statewide saving potentials of 2000 GWh/year and 75 million thermal/year, as well as an electricity peak reduction potential of 0.7 GW. The overall goal of this research program is to provide new technology and application knowledge that will allow the design, construction, and energy services industries to reduce the energy waste associated with thermal distribution systems in California commercial buildings. The specific goals of the LBNL efforts over the past year were: (1) to advance the state of knowledge about system performance and energy losses in commercial-building thermal distribution systems; (2) to evaluate the potential of reducing thermal losses through duct sealing, duct insulation, and improved equipment sizing; and (3) to develop and evaluate innovative techniques applicable to large buildings for sealing ducts and encapsulating internal duct insulation. In the UCB fan project, the goals were: (1) to develop a protocol for testing, analyzing and diagnosing problems in large commercial building built-up air handling systems, and (2) to develop low-cost measurement techniques to improve short term monitoring practices. To meet our stated goals and objectives, this project: (1) continued to investigate and characterize the performance of thermal distribution systems in commercial buildings; (2) performed energy analyses and evaluation for duct-performance improvements for both small and large commercial buildings; (3) developed aerosol injection technologies for both duct sealing and liner encapsulation in commercial buildings; and (4) designed energy-related diagnostic protocols based on short term measurement and used a benchmarking database to compare subject systems with other measured systems for certain performance metrics. This year's efforts consisted of the following distinct tasks: performing characterization measurements for five light commercial building systems and five large-commercial-building systems; analyzing the potential for including duct performance in California's Energy Efficiency Standards for Residential and Non-Residential Buildings (Title 24), including performing energy and equipment sizing analyses of air distribution systems using DOE 2.1E for non-residential buildings; conducting laboratory experiments, field experiments, and modeling of new aerosol injection technologies concepts for sealing and coating, including field testing aerosol-based sealing in two large commercial buildings; improving low-cost fan monitoring techniques measurements, and disseminating fan tools by working with energy practitioners directly where possible and publishing the results of this research and the tools developed on a web-site. The final report consists of five sections listed below. Each section includes its related

Xu, Tengfang; Bechu, Olivier; Carrie, Remi; Dickerhoff, Darryl; Fisk, William; Franconi, Ellen; Kristiansen, Oyvind; Levinson, Ronnen; McWilliams, Jennifer; Wang, Duo; Modera, Mark; Webster, Tom; Ring, Erik; Zhang, Qiang; Huizenga, Charlie; Bauman, Fred; Arens, Ed

1999-12-01T23:59:59.000Z

172

SOLERAS - Solar Energy Water Desalination Project: Catalytic. System design final report. Volume 1. System requirement definition and system analysis  

Science Conference Proceedings (OSTI)

Catalytic Inc. was awarded a contract to conduct a preliminary system design and cost analysis for a brackish water desalination project to be located in Brownsville, Texas. System analyses and economic analyses were performed to define the baseline solar energy desalination system. The baseline system provides an average daily product water capacity of 6000 mT. The baseline system is optimal relative to technological risk, performance, and product water cost. Subsystems and their interfaces have been defined and product water cost projections made for commercial plants in a range of capacities. Science Applications, Inc. (SAI), subcontractor to Catalytic, had responsibility for the solar power system. This, the final report, summarizes the work performed under the Phase I effort.

Not Available

1986-01-01T23:59:59.000Z

173

Solar hydrogen energy system. Annual report, 1995--1996  

DOE Green Energy (OSTI)

The paper reports progress on three tasks. Task A, System comparison of hydrogen with other alternative fuels in terms of EPACT requirements, investigates the feasibility of several alternative fuels, namely, natural gas, methanol, ethanol, hydrogen and electricity, to replace 10% of gasoline by the year 2000. The analysis was divided into two parts: analysis of vehicle technologies and analysis of fuel production, storage and distribution. Task B, Photovoltaic hydrogen production, involves this fuel production method for the future. The process uses hybrid solar collectors to generate dc electricity, as well as high temperature steam for input to the electrolyzer. During the first year, solar to hydrogen conversion efficiencies have been considered. The third task, Hydrogen safety studies, covers two topics: a review of codes, standards, regulations, recommendations, certifications, and pamphlets which address safety of gaseous fuels; and an experimental investigation of hydrogen flame impingement.

Veziroglu, T.N.

1996-12-31T23:59:59.000Z

174

Urban Integrated Industrial Cogeneration Systems Analysis. Phase II final report  

SciTech Connect

Through the Urban Integrated Industrial Cogeneration Systems Analysis (UIICSA), the City of Chicago embarked upon an ambitious effort to identify the measure the overall industrial cogeneration market in the city and to evaluate in detail the most promising market opportunities. This report discusses the background of the work completed during Phase II of the UIICSA and presents the results of economic feasibility studies conducted for three potential cogeneration sites in Chicago. Phase II focused on the feasibility of cogeneration at the three most promising sites: the Stockyards and Calumet industrial areas, and the Ford City commercial/industrial complex. Each feasibility case study considered the energy load requirements of the existing facilities at the site and the potential for attracting and serving new growth in the area. Alternative fuels and technologies, and ownership and financing options were also incorporated into the case studies. Finally, site specific considerations such as development incentives, zoning and building code restrictions and environmental requirements were investigated.

Not Available

1984-01-01T23:59:59.000Z

175

Development of advanced electromagnetic exploration system. Final report  

DOE Green Energy (OSTI)

The electronics system design for both the transmitting system and the receiving system, the laboratory test results obtained on the system completed thus far, and the effort needed to complete the system are detailed. (MHR)

Not Available

1979-08-01T23:59:59.000Z

176

HYDRIDES AND METAL-HYDROGEN SYSTEMS. Final Report  

DOE Green Energy (OSTI)

The work reported deals with the preparation and physical properties, especially thermal dissociation pressures, and densities of hydrides, hydrogen- metal systems, and mixtures of hydrides with other substances. Possible applicatlons as moderators, high-temperature neutron shields, and low-temperature shields are cited and design problems discussed. Most of the data on dissociation pressures cover ranges and compounds not hltherto explored because of experimental difficulties and the basic knowledge of the thermal behavior of hydrides was substantially increased. New hydrldes were prepared and several reported in the literature were shown not to exist. The following compounds, mixtures, and systems were studled: Tl-H, U-H, Ll-H, Na-H, Ca-H, Ba-H, Th-H, Sr- H; NaH-NaF, NaH-NaOH, NaH-CaH/, LlH-LiF, CaH/sub 2/-CaF/sub 2/, CaH/sub 2/-CaC/ sub 2/,CaH/sub 2/-Ca/sub 3/N/sub 2/; FeH/sub 3/ (alleged), NiH/sub 2/ (alleged), Ti(BH/sub 4/)/sub 3/, Th(BH/sub 4/)/sub 4/, WH/sub 4/ (attempted), W(BH/sub 4/)/ sub 4/ (attempted), /sub 4/NBH/sub 4/, (CH , and ydrides are ing an N/sub H/ comparable to water yet stable at red heat, compounds giving a neutron shield weight less than half that of water, and compounds suitable for use as hightemperature moderators containing large amounts of hydrogen. (auth)

Gibb, T.R.P. Jr.

1951-04-30T23:59:59.000Z

177

Pentek metal coating removal system: Baseline report; Greenbook (chapter)  

SciTech Connect

The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

1997-07-31T23:59:59.000Z

178

Community-Level Impacts Projection System (CLIPS). Final report  

DOE Green Energy (OSTI)

The Community-Level Impacts Projection System includes a set of techniques for providing detailed advance information required for rational planning. The computerized system generates reports which enable the user: to describe the energy development activity in terms of its employment demands and spatial location; to estimate how many in-migrating workers will be required; to estimate the demographic characteristics of the in-migrating workers (e.g., how many elementary school children they will bring); to estimate how many additional secondary employment opportunities (e.g., employment in eating and drinking establishments and grocery stores) will be generated; to estimate what the local area's population levels in various age groups would be both with the project and without it; to estimate community population levels for both the impact case and the baseline case; and to estimate the approximate resource requirements and costs for providing additional municipal facilities and services (e.g., water treatment and distribution, wastewater treatment and collection, gas and electric distribution, police and fire protection, etc.)

Monts, J.K.; Bareiss, E.R.

1979-02-01T23:59:59.000Z

179

50 kW PEM Fuel Cell System Design, Fabrication, and Test: System Design -- Final Report  

Science Conference Proceedings (OSTI)

This final report describes the results of a development program funded jointly by the U.S. Department of Energy, Arthur D. Little, and EPRIsolutions. The effort was aimed at the conceptual design and optimization of a 50 kW commercial power system, using advanced proton exchange (or polymer electrolyte) membrane fuel cell (PEMFC) technology and the verification of key design parameters. (Note: This design effort addresses some of the key technical issues faced by the developers of commercial-scale PEMFC...

2000-12-11T23:59:59.000Z

180

MRS (monitored retrievable storage) Systems Study Task 1 report: Waste management system reliability analysis  

Science Conference Proceedings (OSTI)

This is one of nine studies undertaken by contractors to the US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), to provide a technical basis for re-evaluating the role of a monitored retrievable storage (MRS) facility. The study evaluates the relative reliabilities of systems with and without an MRS facility using current facility design bases. The principal finding of this report is that the MRS system has several operational advantages that enhance system reliability. These are: (1) the MRS system is likely to encounter fewer technical issues, (2) the MRS would assure adequate system surface storage capacity to accommodate repository construction and startup delays of up to five years or longer if the Nuclear Waste Policy Amendments Act (NWPAA) were amended, (3) the system with an MRS has two federal acceptance facilities with parallel transportation routing and surface storage capacity, and (4) the MRS system would allow continued waste acceptance for up to a year after a major disruption of emplacement operations at the repository.

Clark, L.L.; Myers, R.S.

1989-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Prototype Engineered Barrier System Field Test (PEBSFT); Final report  

SciTech Connect

This final report represents a summary of data and interpretations obtained from the Prototype Engineered Barrier System Field Test (PEBSFT) performed in G-Tunnel within the Nevada Test Site. The PEBSFT was conducted to evaluate the applicability of measurement techniques, numerical models, and procedures developed for future field tests that will be conducted in the Exploratory Studies Facilities (ESF) at Yucca Mountain. The primary objective of the test was to provide a basis for determining whether tests planned for the ESF have the potential to be successful. Chapter 1 on high frequency electromagnetic tomography discusses the rock mass electromagnetic permittivity and attenuation rate changes that were measured to characterize the water distribution in the near field of a simulated waste container. The data are used to obtain quantitative estimates of how the moisture content in the rock mass changes during heating and to infer properties of the spatial variability of water distribution, leading to conclusions about the role of fractures in the system. Chapter 2 discusses the changes in rock moisture content detected by the neutron logging probe. Chapter 3 permeability tests discusses the characterization of the in-situ permeability of the fractured tuff around the borehole. The air permeability testing apparatus, the testing procedures, and the data analysis are presented. Chapter 4 describes the moisture collection system installed in the heater borehole to trap and measure the moisture volumes. Chapter 5 describes relative humidity measurements made with the thermocouple psychrometer and capacitance sensors. Chapter 6 discusses gas pressure measurements in the G-Tunnel, addressing the calibration and installation of piezoresistive-gaged transducers. Chapter 7 describes the calibration and installation of thermocouples for temperature measurements. Chapter 8 discusses the results of the PEBSFT.

Ramirez, A.L. [ed.; Buscheck, T.; Carlson, R.; Daily, W.; Lee, K.; Lin, Wunan; Mao, Nai-hsien; Ueng, Tzou-Shin; Wang, H.; Watwood, D.

1991-08-01T23:59:59.000Z

182

FY 93 Thermal Loading Systems Study Final Report  

Science Conference Proceedings (OSTI)

The objective of the Mined Geologic Disposal System (MGDS) Thermal Loading Systems Study being conducted by the is to identify a thermal strategy that will meet the performance requirements for waste isolation and will be safe and licensable. Specifically, both postclosure and preclosure performance standards must be met by the thermal loading strategy ultimately selected. In addition cost and schedule constraints must be considered. The Systems Engineering approach requires structured, detailed analyses that will ultimately provide the technical basis for the development, integration, and evaluation of the overall system, not just a subelement of that system. It is also necessary that the systems study construct options from within the range that are allowed within the current legislative and programmatic framework. For example the total amount of fuel that can legally be emplaced is no more than 70,000 metric tons of uranium (MTU) which is composed of 63,000 MTU spent fuel and 7,000 MTU of defense high level waste. It is the intent of this study to begin the structured development of the basis for a thermal loading decision. However, it is recognized that to be able to make a final decision on thermal loading will require underground data on the effects of heating as well as a suite of ''validated'' models. It will be some time before these data and models are available to the program. Developing a final, thermal loading decision will, therefore, be an iterative process. In the interim, the objective of the thermal loading systems study has been to utilize the information available to assess the impact of thermal loading. Where technical justification exists, recommendations to narrow the range of thermal loading options can be made. Additionally, recommendations as to the type of testing and accuracy of the testing needed to establish the requisite information will be made. A constraint on the ability of the study to select an option stems from the lack of primary hard data, uncertainties in derived data, unsubstantiated models, and the inability to fully consider simultaneously coupled processes. As such, the study must rely on idealized models and available data to compare the thermal loading options. This report presents the findings of the FY 1993 MGDS Thermal Loading Systems Study. The objectives of the study were to: (1) if justified, place bounds on the thermal loading which would establish the loading that is ''too hot''; (2) ''grade'' or evaluate the performance as a function of thermal loading of the potential repository to contain high level spent nuclear fuel against performance criteria; (3) evaluate the performance of the various options with respect to cost, safety, and operability; and (4) recommend the additional types of tests and/or analyses to be conducted to provide the necessary information for a thermal loading selection.

S.F. Saterlie

1994-08-29T23:59:59.000Z

183

Environmental Systems Research Candidates Program--FY2000 Annual report  

SciTech Connect

The Environmental Systems Research Candidates (ESRC) Program, which is scheduled to end September 2001, was established in April 2000 as part of the Environmental Systems Research and Analysis Program at the Idaho National Engineering and Environmental Laboratory (INEEL) to provide key science and technology to meet the clean-up mission of the U.S. Department of Energy Office of Environmental Management, and perform research and development that will help solve current legacy problems and enhance the INEELs scientific and technical capability for solving longer-term challenges. This report documents the progress and accomplishments of the ESRC Program from April through September 2000. The ESRC Program consists of 24 tasks subdivided within four research areas: A. Environmental Characterization Science and Technology. This research explores new data acquisition, processing, and interpretation methods that support cleanup and long-term stewardship decisions. B. Subsurface Understanding. This research expands understanding of the biology, chemistry, physics, hydrology, and geology needed to improve models of contamination problems in the earths subsurface. C. Environmental Computational Modeling. This research develops INEEL computing capability for modeling subsurface contaminants and contaminated facilities. D. Environmental Systems Science and Technology. This research explores novel processes to treat waste and decontaminate facilities. Our accomplishments during FY 2000 include the following: We determined, through analysis of samples taken in and around the INEEL site, that mercury emissions from the INEEL calciner have not raised regional off-INEEL mercury contamination levels above normal background. We have initially demonstrated the use of x-ray fluorescence to image uranium and heavy metal concentrations in soil samples. We increased our understanding of the subsurface environment; applying mathematical complexity theory to the problem of transport of subsurface contaminants. We upgraded the INEELs high-speed computer link to offsite supercomputers from T1 (1.5 MB/s) to DS3 (45 MB/s). Procurements have initiated a further upgrade to OC3 (155 MB/s) with additional onsite computational power that should put the INEEL on the Top 500 Supercomputing Sites list. We developed advanced decontamination, decommissioning, and dismantlement techniques, including the Decontamination, Decommissioning, and Remediation Optimal Planning System.

Piet, Steven James

2001-01-01T23:59:59.000Z

184

[Advanced Gas Turbine Systems Research]. Technical Quarterly Progress Report  

Science Conference Proceedings (OSTI)

Major Accomplishments by Advanced Gas Turbine Systems Research (AGTSR) during this reporting period are highlighted below and amplified in later sections of this report: AGTSR distributed 50 proposals from the 98RFP to the IRB for review, evaluation and rank-ordering during the summer; AGTSR conducted a detailed program review at DOE-FETC on July 24; AGTSR organized the 1998 IRB proposal review meeting at SCIES on September 15-16; AGTSR consolidated all the IRB proposal scores and rank-orderings to facilitate the 98RFP proposal deliberations; AGTSR submitted meeting minutes and proposal short-list recommendation to the IRB and DOE for the 98RFP solicitation; AGTSR reviewed two gas turbine related proposals as part of the CU RFP State Project for renovating the central energy facility; AGTSR reviewed and cleared research papers with the IRB from the University of Pittsburgh, Wisconsin, and Minnesota; AGTSR assisted GTA in obtaining university stakeholder support of the ATS program from California, Pennsylvania, and Colorado; AGTSR assisted GTA in distributing alert notices on potential ATS budget cuts to over 150 AGTSR performing university members; AGTSR submitted proceedings booklet and organizational information pertaining to the OAI hybrid gas turbine workshop to DOE-FETC; For DOE-FETC, AGTSR updated the university consortium poster to include new members and research highlights; For DOE-FETC, the general AGTSR Fact Sheet was updated to include new awards, workshops, educational activity and select accomplishments from the research projects; For DOE-FETC, AGTSR prepared three fact sheets highlighting university research supported in combustion, aero-heat transfer, and materials; For DOE-FETC, AGTSR submitted pictures on materials research for inclusion in the ATS technology brochure; For DOE-FETC, AGTSR submitted a post-2000 roadmap showing potential technology paths AGTSR could pursue in the next decade; AGTSR distributed the ninth newsletter UPDATE to DOE, the IRB: and two interested partners involved in ATS; AGTSR submitted information on its RFP's, workshops, and educational activities for the 1999 ASMWIGTI technology report for worldwide distribution; AGTSR coordinated university poster session titles and format with Conference Management Associates (CMA) for the 98 ATS Annual; and AGTSR submitted 2-page abstract to CMA for the 98 ATS Review titled: ''AGTSR: A Virtual National Lab''.

NONE

1998-09-30T23:59:59.000Z

185

Advanced turbine systems program conceptual design and product development. Quarterly report, August--October 1994  

SciTech Connect

This is a quarterly report on the Westinghouse Electric Corporation Advanced Turbine Systems Program--conceptual design and product development. The topics of the report include the management plan, National Energy Policy Act, selection of natural gas-fired advanced turbine systems, selection of coal-fired advanced turbine systems, market study, systems definition and analysis, design and test of critical components, and plans for the next reporting period.

1994-12-01T23:59:59.000Z

186

CMR Shuffler System: Passive Mode Calibration and Certification Report  

Science Conference Proceedings (OSTI)

Los Alamos National Laboratory has a number of spherical confinement vessels (CVs) remaining from tests involving nuclear materials. These vessels have an inner diameter of 6 feet with 1 to 2 inch thick steel walls. The goal of the Confinement Vessel Disposition (CVD) project is to remove debris and reduce contamination inside the vessels. As debris is removed from the vessels, material will be placed in waste drums. Far-field gamma ray assay will be used to determine when a drum is nearing a {sup 239}Pu equivalent mass of less than 200 g. The drum will then be assayed using a waste drum shuffler operated in passive mode using a neutron coincidence counting method for accountability. This report focuses on the testing and calibration of the CMR waste drum shuffler in passive mode operation. Initial testing was performed to confirm previously accepted measurement parameters. The system was then calibrated using a set of weapons grade Pu (WGPu, {sup 239}Pu > 93%) oxide standards placed inside a 55 gallon drum. The calibration data ranges from Pu mass of 0.5 g to 188.9 g. The CMR waste drum shuffler has been tested and calibrated in passive mode in preparation for safeguards accountability measurements of waste drums containing material removed from CVs for the CVD project.

Frame, Katherine C. [Los Alamos National Laboratory; Gomez, Cipriano D. [Retired CMR-OPS: OPERATIONS; Salazar, William R. [Los Alamos National Laboratory; Mayo, Douglas R. [Los Alamos National Laboratory; Vigil, Georgiana M. [Los Alamos National Laboratory; Crooks, William J. [Los Alamos National Laboratory; Stange, Sy [Los Alamos National Laboratory

2012-07-20T23:59:59.000Z

187

Residential end-use energy planning system (REEPS). Final report  

Science Conference Proceedings (OSTI)

The Residential End-Use Energy Planning System (REEPS) is described. REEPS is a forecasting model of residential energy patterns that is capable of evaluating the impacts of a broad range of energy conservation measures. REEPS forecasts appliance installations, operating efficiencies, and utilization patterns for space heating, water heating, air conditioning, and cooking. Each of these decisions is sensitive to energy prices, mandatory policies, and household/dwelling and geographical characteristics. The parameters of these choice models have been estimated statistically from national household survey data. The structure of the choice models and the results of the statistical analysis are reported in detail. REEPS forecasts energy choices for a large number of market segments representing households with different socioeconomic, dwelling, and geographical characteristics. These segments reflect the joint distribution of characteristics in the population. Aggregate forecasts are generated by summing up the decisions for all population segments. This technique provides a consistent method of obtaining aggregate forecasts from disaggregate, nonlinear choice models. Moreover, it permits evaluation of the distributional impacts of prospective conservation policies. The results of simulation of REEPS are described. REEPS forecasts a moderate rise in electricity consumption per household and significant drops in other fuels. These are caused in part by high market penetrations of electric appliances which themselves reflect major shifts in relative energy prices.

Goett, A.; McFadden, D.

1982-07-01T23:59:59.000Z

188

Hanford site tank waste remediation system programmatic environmental review report  

Science Conference Proceedings (OSTI)

The US Department of Energy (DOE) committed in the Tank Waste Remediation System (TWRS) Environmental Impact Statement (EIS) Record of Decision (ROD) to perform future National Environmental Policy Act (NEPA) analysis at key points in the Program. Each review will address the potential impacts that new information may have on the environmental impacts presented in the TWRS EIS and support an assessment of whether DOE`s plans for remediating the tank waste are still pursuing the appropriate plan for remediation or whether adjustments to the program are needed. In response to this commitment, DOE prepared a Supplement Analysis (SA) to support the first of these reevaluations. Subsequent to the completion of the SA, the Phase IB negotiations process with private contractors resulted in several changes to the planned approach. These changes along with other new information regarding the TWRS Program have potential implications for Phase 1 and Phase 2 of tank waste retrieval and waste storage and/or disposal that may influence the environmental impacts of the Phased Implementation alternative. This report focuses on identifying those potential environmental impacts that may require NEPA analysis prior to authorization to begin facility construction and operations.

Haass, C.C.

1998-09-03T23:59:59.000Z

189

Engineered Barrier Systems Thermal-Hydraulic-Chemical Column Test Report  

SciTech Connect

The Engineered Barrier System (EBS) Thermal-Hydraulic-Chemical (THC) Column Tests provide data needed for model validation. The EBS Degradation, Flow, and Transport Process Modeling Report (PMR) will be based on supporting models for in-drift THC coupled processes, and the in-drift physical and chemical environment. These models describe the complex chemical interaction of EBS materials, including granular materials, with the thermal and hydrologic conditions that will be present in the repository emplacement drifts. Of particular interest are the coupled processes that result in mineral and salt dissolution/precipitation in the EBS environment. Test data are needed for thermal, hydrologic, and geochemical model validation and to support selection of introduced materials (CRWMS M&O 1999c). These column tests evaluated granular crushed tuff as potential invert ballast or backfill material, under accelerated thermal and hydrologic environments. The objectives of the THC column testing are to: (1) Characterize THC coupled processes that could affect performance of EBS components, particularly the magnitude of permeability reduction (increases or decreases), the nature of minerals produced, and chemical fractionation (i.e., concentrative separation of salts and minerals due to boiling-point elevation). (2) Generate data for validating THC predictive models that will support the EBS Degradation, Flow, and Transport PMR, Rev. 01.

W.E. Lowry

2001-12-13T23:59:59.000Z

190

Economic development through biomass system integration: Summary report  

DOE Green Energy (OSTI)

Alfalfa is a well-known and widely-planted crop that offers environmental and soil conservation advantages when grown as a 4-year segment in a 7-year rotation with corn and soybeans. Alfalfa fixes nitrogen from the air, thereby enhancing soil nitrogen and decreasing the need for manufactured nitrogen fertilizer. With alfalfa yields of 4 dry tons per acre per year and the alfalfa leaf fraction sold as a high-value animal feed the remaining alfalfa stem fraction can be economically viable fuel feedstock for a gasifier combined cycle power plant. This report is a feasibility study for an integrated biomass power system, where an energy crop (alfalfa) is the feedstock for a processing plant and a power power plant (integrated gasification combined cycle) in a way that benefits the facility owners. The sale of an animal feed co-product and electricity both help cover the production cost of alfalfa and the feedstock processing cost, thereby requiring neither the electricity or leaf meal to carry the total cost. The power plant provides an important continous demand for the feedstock and results in continous supply of leaf product to provide a reliable supply needed for the leaf meal product.

DeLong, M.M. [Northern States Power Co., Minneapolis, MN (United States)

1995-10-01T23:59:59.000Z

191

Columbia River Hatchery Reform System-Wide Report.  

SciTech Connect

The US Congress funded the Puget Sound and Coastal Washington Hatchery Reform Project via annual appropriations to the US Fish and Wildlife Service (USFWS) beginning in fiscal year 2000. Congress established the project because it recognized that while hatcheries have a necessary role to play in meeting harvest and conservation goals for Pacific Northwest salmonids, the hatchery system was in need of comprehensive reform. Most hatcheries were producing fish for harvest primarily to mitigate for past habitat loss (rather than for conservation of at-risk populations) and were not taking into account the effects of their programs on naturally spawning populations. With numerous species listed as threatened or endangered under the Endangered Species Act (ESA), conservation of salmon in the Puget Sound area was a high priority. Genetic resources in the region were at risk and many hatchery programs as currently operated were contributing to those risks. Central to the project was the creation of a nine-member independent scientific review panel called the Hatchery Scientific Review Group (HSRG). The HSRG was charged by Congress with reviewing all state, tribal and federal hatchery programs in Puget Sound and Coastal Washington as part of a comprehensive hatchery reform effort to: conserve indigenous salmonid genetic resources; assist with the recovery of naturally spawning salmonid populations; provide sustainable fisheries; and improve the quality and cost-effectiveness of hatchery programs. The HSRG worked closely with the state, tribal and federal managers of the hatchery system, with facilitation provided by the non-profit organization Long Live the Kings and the law firm Gordon, Thomas, Honeywell, to successfully complete reviews of over 200 hatchery programs at more than 100 hatcheries across western Washington. That phase of the project culminated in 2004 with the publication of reports containing the HSRG's principles for hatchery reform and recommendations for Puget Sound/Coastal Washington hatchery programs, followed by the development in 2005 of a suite of analytical tools to support application of the principles (all reports and tools are available at www.hatcheryreform.us). In 2005, Congress directed the National Oceanic and Atmospheric Administration-Fisheries (NOAA Fisheries) to replicate the Puget Sound and Coastal Washington Hatchery Reform Project in the Columbia River Basin. The HSRG was expanded to 14 members to include individuals with specific knowledge about the Columbia River salmon and steelhead populations. This second phase was initially envisioned as a one-year review, with emphasis on the Lower Columbia River hatchery programs. It became clear however, that the Columbia River Basin needed to be viewed as an inter-connected ecosystem in order for the review to be useful. The project scope was subsequently expanded to include the entire Basin, with funding for a second year provided by the Bonneville Power Administration (BPA) under the auspices of the Northwest Power and Conservation Council's (NPCC) Fish and Wildlife Program. The objective of the HSRG's Columbia River Basin review was to change the focus of the Columbia River hatchery system. In the past, these hatchery programs have been aimed at supplying adequate numbers of fish for harvest as mitigation primarily for hydropower development in the Basin. A new, ecosystem-based approach is founded on the idea that harvest goals are sustainable only if they are compatible with conservation goals. The challenge before the HSRG was to determine whether or not conservation and harvest goals could be met by fishery managers and, if so, how. The HSRG determined that in order to address these twin goals, both hatchery and harvest reforms are necessary. The HSRG approach represents an important change of direction in managing hatcheries in the region. It provides a clear demonstration that current hatchery programs can indeed be redirected to better meet both conservation and harvest goals. For each Columbia River Basin Environmentally Si

Warren, Dan [Hatchery Scientific Review Group

2009-04-16T23:59:59.000Z

192

Columbia River Hatchery Reform System-Wide Report.  

DOE Green Energy (OSTI)

The US Congress funded the Puget Sound and Coastal Washington Hatchery Reform Project via annual appropriations to the US Fish and Wildlife Service (USFWS) beginning in fiscal year 2000. Congress established the project because it recognized that while hatcheries have a necessary role to play in meeting harvest and conservation goals for Pacific Northwest salmonids, the hatchery system was in need of comprehensive reform. Most hatcheries were producing fish for harvest primarily to mitigate for past habitat loss (rather than for conservation of at-risk populations) and were not taking into account the effects of their programs on naturally spawning populations. With numerous species listed as threatened or endangered under the Endangered Species Act (ESA), conservation of salmon in the Puget Sound area was a high priority. Genetic resources in the region were at risk and many hatchery programs as currently operated were contributing to those risks. Central to the project was the creation of a nine-member independent scientific review panel called the Hatchery Scientific Review Group (HSRG). The HSRG was charged by Congress with reviewing all state, tribal and federal hatchery programs in Puget Sound and Coastal Washington as part of a comprehensive hatchery reform effort to: conserve indigenous salmonid genetic resources; assist with the recovery of naturally spawning salmonid populations; provide sustainable fisheries; and improve the quality and cost-effectiveness of hatchery programs. The HSRG worked closely with the state, tribal and federal managers of the hatchery system, with facilitation provided by the non-profit organization Long Live the Kings and the law firm Gordon, Thomas, Honeywell, to successfully complete reviews of over 200 hatchery programs at more than 100 hatcheries across western Washington. That phase of the project culminated in 2004 with the publication of reports containing the HSRG's principles for hatchery reform and recommendations for Puget Sound/Coastal Washington hatchery programs, followed by the development in 2005 of a suite of analytical tools to support application of the principles (all reports and tools are available at www.hatcheryreform.us). In 2005, Congress directed the National Oceanic and Atmospheric Administration-Fisheries (NOAA Fisheries) to replicate the Puget Sound and Coastal Washington Hatchery Reform Project in the Columbia River Basin. The HSRG was expanded to 14 members to include individuals with specific knowledge about the Columbia River salmon and steelhead populations. This second phase was initially envisioned as a one-year review, with emphasis on the Lower Columbia River hatchery programs. It became clear however, that the Columbia River Basin needed to be viewed as an inter-connected ecosystem in order for the review to be useful. The project scope was subsequently expanded to include the entire Basin, with funding for a second year provided by the Bonneville Power Administration (BPA) under the auspices of the Northwest Power and Conservation Council's (NPCC) Fish and Wildlife Program. The objective of the HSRG's Columbia River Basin review was to change the focus of the Columbia River hatchery system. In the past, these hatchery programs have been aimed at supplying adequate numbers of fish for harvest as mitigation primarily for hydropower development in the Basin. A new, ecosystem-based approach is founded on the idea that harvest goals are sustainable only if they are compatible with conservation goals. The challenge before the HSRG was to determine whether or not conservation and harvest goals could be met by fishery managers and, if so, how. The HSRG determined that in order to address these twin goals, both hatchery and harvest reforms are necessary. The HSRG approach represents an important change of direction in managing hatcheries in the region. It provides a clear demonstration that current hatchery programs can indeed be redirected to better meet both conservation and harvest goals. For each Columbia River Basin Environmentally Significant Unit

Warren, Dan [Hatchery Scientific Review Group

2009-04-16T23:59:59.000Z

193

APS Alternative Fuel (Hydrogen) Pilot Plant - Monitoring System Report  

DOE Green Energy (OSTI)

The U.S. Department of Energys (DOEs) Advanced Vehicle Testing Activity (AVTA), along with Electric Transportation Applications and Arizona Pubic Service (APS), is monitoring the operations of the APS Alternative Fuel (Hydrogen) Pilot Plant to determine the costs to produce hydrogen fuels (including 100% hydrogen as well as hydrogen and compressed natural gas blends) for use by fleets and other operators of advanced-technology vehicles. The hydrogen fuel cost data will be used as benchmark data by technology modelers as well as research and development programs. The Pilot Plant can produce up to 18 kilograms (kg) of hydrogen per day by electrolysis. It can store up to 155 kg of hydrogen at various pressures up to 6,000 psi. The dispenser island can fuel vehicles with 100% hydrogen at 5,000 psi and with blends of hydrogen and compressed natural gas at 3,600 psi. The monitoring system was designed to track hydrogen delivery to each of the three storage areas and to monitor the use of electricity on all major equipment in the Pilot Plant, including the fuel dispenser island. In addition, water used for the electrolysis process is monitored to allow calculation of the total cost of plant operations and plant efficiencies. The monitoring system at the Pilot Plant will include about 100 sensors when complete (50 are installed to date), allowing for analysis of component, subsystems, and plant-level costs. The monitoring software is mostly off-the-shelve, with a custom interface. The majority of the sensors input to the Programmable Automation Controller as 4- to 20-mA analog signals. The plant can be monitored over of the Internet, but the control functions are restricted to the control room equipment. Using the APS general service plan E32 electric rate of 2.105 cents per kWh, during a recent eight-month period when 1,200 kg of hydrogen was produced and the plant capacity factor was 26%, the electricity cost to produce one kg of hydrogen was $3.43. However, the plant capacity factor has been increasing, with a recent one-month high of 49%. If a plant capacity factor of 70% can be achieved with the present equipment, the cost of electricity would drop to $2.39 per kg of hydrogen. In this report, the power conversion (76.7%), cell stack (53.1%), and reverse osmosis system (7.14%) efficiencies are also calculated, as is the water cost per kg of hydrogen produced ($0.10 per kg). The monitoring system has identified several areas having the potential to lower costs, including using an reverse osmosis system with a higher efficiency, improving the electrolysis power conversion efficiency, and using air cooling to replace some or all chiller cooling. These activities are managed by the Idaho National Laboratory for the AVTA, which is part of DOEs FreedomCAR and Vehicle Technologies Program.

James Francfort; Dimitri Hochard

2005-07-01T23:59:59.000Z

194

Photovoltaic systems concept study. Final report. Volume I  

DOE Green Energy (OSTI)

Conceptual system designs were developed for three sizes of photovoltaic solar electric power systems: a single family residence, a central station power plant, and two on-site intermediate systems (shopping center and commercial retrofit). A brief system description and a summary of primary performance and economic characteristics are included for each of the three system designs. Principal conclusions for each are highlighted and overall system comparisons and recommendations are set forth. (MHR)

Not Available

1977-04-01T23:59:59.000Z

195

Microprocessor controlled solar collector system. Technical progress report No. 3  

SciTech Connect

The strategy and initial results of a microprocessor control system for a solar water heating system are described. Two hot water storage tanks are utilized. (WHK)

1979-11-15T23:59:59.000Z

196

Ris Energy Report 4 Supply technologies in the future energy system 10 Supply technologies in the future energy system  

E-Print Network (OSTI)

Risø Energy Report 4 Supply technologies in the future energy system 10 Supply technologies of local and central production and close coupling between supply and end-use. Wind Global wind energy: Energy supply technologies #12;Risø Energy Report 4 Supply technologies in the future energy system4 used

197

Bioenergy systems report. April 1984: innovations in biogas systems and technology  

Science Conference Proceedings (OSTI)

A comprehensive review of recent innovations in the design and operation of biogas systems is presented. The report contains information on about sixty distinct designs for biogas plants. These include plants designed for use by individual families, larger farm plants, plants used for the digestion of agroindustrial residues, and plants producing or recovering biogas from human wastes and residues. Some have been designed for use in developing countries; others have been used primarily in developed countries but may involve design elements that could be utilized in developing countries.

Mahin, D.B.

1984-04-01T23:59:59.000Z

198

CFD Simulation of Airflow in Ventilated Wall System Report #9  

DOE Green Energy (OSTI)

The objective of this report was to examine air movements in vinyl and brick ventilation cavities in detail, using a state of the art CFD commercial modeling tool. The CFD activity was planned to proceed the other activities in order to develop insight on the important magnitudes of scales occurring during ventilation air flow. This information generated by the CFD model was to be used to modify (if necessary) and to validate the air flow dynamics already imbedded in the hygrothermal model for the computer-based air flow simulation procedures. A comprehensive program of advanced, state-of-the-art hygrothermal modeling was then envisaged mainly to extend the knowledge to other wall systems and at least six representative climatic areas. These data were then to be used to provide the basis for the development of design guidelines. CFD results provided timely and much needed answers to many of the concerns and questions related to ventilation flows due to thermal buoyancy and wind-driven flow scenarios. The relative strength between these two mechanisms. Simple correlations were developed and are presented in the report providing the overall pressure drop, and flow through various cavities under different exterior solar and temperature scenarios. Brick Rainscreen Wall: It was initially expected that a 50 mm cavity would offer reduced pressure drops and increased air flow compared to a 19 mm cavity. However, these models showed that the size of the ventilation slots through the wall are the limiting factor rather than the cavity depth. Of course, once the slots are enlarged beyond a certain point, this could change. The effects of natural convection within the air cavities, driven by the temperature difference across the cavity, were shown to be less important than the external wind speed (for a wind direction normal to the wall surface), when wind action is present. Vinyl Rainscreen Wall: The CFD model of the vinyl rainscreen wall was simpler than that for the brick wall. Constant wall temperatures were used rather than conjugate heat transfer. Although this is appropriate for a thin surface with little heat capacity, it does mean that an empirical correlation between solar radiation (and perhaps wind speed) and vinyl temperature is required to use these results appropriately. The results developed from this CFD model were correlated to weather parameters and construction details so that they can be incorporated into ORNL s advanced hygrothermal models MOISTURE- EXPERT.

Stovall, Therese K [ORNL; Karagiozis, Achilles N [ORNL

2004-01-01T23:59:59.000Z

199

Solar House Sink Group HVAC System Design Final Report  

E-Print Network (OSTI)

In this project we apply a systems engineering approach to design an intelligent HVAC system. Using sensors and user provided information the systems determines and adjusts the cooling load on the fly to provide the most efficient operation possible, saving energy and money. The system utilizes variable speed drives to provide just enough capacity to keep the indoor

Bob Hayes; Will Seeber; Zhen Zhao; Zhen Kuang; Isr Advisor; Prof Austin; Prof Baras

2011-01-01T23:59:59.000Z

200

Heavy Vehicle Systems Optimization 2003 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

... 55 A. Cooling Fan and System Performance and Efficiency Improvements Caterpillar Incorporated; R.L....

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Solar energy management systems development program. Final report  

DOE Green Energy (OSTI)

This document describes the requirements of a general-purpose solar controller, the novel control system, and sample application of that system. The investigation showed that solar systems vary in terms of temperature setpoints and differentials. Also, system design details, such as the particular placement of temperatur sensors, lengths or types of ducts, etc., affect setpoint and differential values, even for systems with similar mechanical schematics. (MOW)

None

202

Photovoltaic systems concept study. Volume IV. Final report  

DOE Green Energy (OSTI)

This report has been prepared in nine sections plus appendices, separated into five separate volumes. This volume contains three sections. Separate abstracts were prepared for each section. (MHR)

Not Available

1977-04-01T23:59:59.000Z

203

Design Review Closure Report for the SY-101 Rapid Transfer System  

SciTech Connect

The purpose of this report, is to document closure of design review open items, resulting from design reviews conducted for the SY-101 Respond And Pump In Days (RAPID) Transfer System. Results of the various design reviews were documented in the Design Review Report for The SY-101 Rapid Mitigation System, HNF-4519. In that report, twenty-three open items were identified. In this report the 23 items are reviewed and statused.

POWELL, W.J.

1999-11-29T23:59:59.000Z

204

"Supervisory Control and Data Acquisition (SCADA) Systems." The CIP Report.  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

"Supervisory Control and Data Acquisition (SCADA) Systems." The CIP "Supervisory Control and Data Acquisition (SCADA) Systems." The CIP Report. Vol 7 No 8 "Supervisory Control and Data Acquisition (SCADA) Systems." The CIP Report. Vol 7 No 8 Featured in this month's issue of The CIP Report are Supervisory Control and Data Acquisition (SCADA) systems. SCADA systems monitor and control the processes of many of our Nation's infrastructures. The security and safety of transportation, water, communications, and many other vital parts of our everyday lives all rely on SCADA systems. In this issue we look at some of the different SCADA systems and their applications. The CIP Report More Documents & Publications The CIP Report, Vol.11, No. 2 (August 2012): Smart Grid Security Introduction SCADA Security for Managers and Operators

205

Advanced thermal barrier coating system development: Technical progress report  

DOE Green Energy (OSTI)

Objectives are to provide an improved TBC system with increased temperature capability and improved reliability. Such coating systems are essential to the ATS engine (gas turbine) meeting its objectives.

NONE

1996-12-11T23:59:59.000Z

206

Survey Report: Improving Integration of Program Management and Systems Engineering  

E-Print Network (OSTI)

Formanyyears,aculturalbarrierhasexistedbetweenpractitionersofsystemsengineeringandofprogrammanagement.Somesystemsengineersandprogrammanagershavedevelopedthemindsetthattheirworkactivitiesar ...

Conforto, Edivandro

207

Framework for Adaptable Operating and Runtime Systems: Final Project Report  

SciTech Connect

In this grant, we examined a wide range of techniques for constructing high-performance con#12;gurable system software for HPC systems and its application to DOE-relevant problems. Overall, research and development on this project focused in three specifc areas: (1) software frameworks for constructing and deploying con#12;gurable system software, (2) applcation of these frameworks to HPC-oriented adaptable networking software, (3) performance analysis of HPC system software to understand opportunities for performance optimization.

Patrick G. Bridges

2012-02-01T23:59:59.000Z

208

Partial control of complex processing systems. Final Report  

Science Conference Proceedings (OSTI)

Research program for the design and control of advanced chemical process systems, typified by refineries/petro chemical plants.

Shinnar, Reuel; Rinard, Irv

2003-04-17T23:59:59.000Z

209

Accelerating PV Cost Effectiveness Through Systems Design, Engineering, and Quality Assurance: Final Subcontract Report, June 2007  

SciTech Connect

This report describes PowerLight Corporation's significant progress toward the reduction of installed costs for commercial-scale, rooftop PV systems.

Botkin, J.

2007-12-01T23:59:59.000Z

210

Distributed Energy Systems in California's Future: A Preliminary Report Volume 2  

E-Print Network (OSTI)

Systems . District Solar Heating Biomass Conversion WindPacific Regional Solar Heating Handbook, San Francisco,Institutions About Solar Heating in the Home. Draft Report

Balderston, F.

2010-01-01T23:59:59.000Z

211

Accelerating PV Cost Effectiveness Through Systems Design, Engineering, and Quality Assurance: Final Subcontract Report, June 2007  

DOE Green Energy (OSTI)

This report describes PowerLight Corporation's significant progress toward the reduction of installed costs for commercial-scale, rooftop PV systems.

Botkin, J.

2007-12-01T23:59:59.000Z

212

Advanced turbine systems program conceptual design and product development quarterly report, May--July 1995  

Science Conference Proceedings (OSTI)

Progress for the quarter is reported in the areas of system definition and analysis and design and test of critical components.

NONE

1995-08-01T23:59:59.000Z

213

PC Electronic Data Reporting Option (PEDRO) System Users Guide  

U.S. Energy Information Administration (EIA)

PC Electronic Data Reporting Option (PEDRO) System Users Guide Version 6.2 Energy Information Administration U.S. Department of Energy Washington, ...

214

Parabolic Trough Solar System Piping Model: Final Report, 13 May 2002 ? 31 December 2004  

DOE Green Energy (OSTI)

Subcontract report by Nexant, Inc., and Kearny and Associates regarding a study of a piping model for a solar parabolic trough system.

Kelly, B.; Kearney, D.

2006-07-01T23:59:59.000Z

215

Lower Flathead System Fisheries Study, 1984 Annual Report.  

DOE Green Energy (OSTI)

This study was undertaken to assess the effects of Kerr Dam operations on the fisheries of the Lower Flathead System. Supported by Bonneville Power Administration funding, and conducted by the Confederated Salish and Kootenai Tribes, the study began in December of 1982 and is scheduled for completion in December of 1987. This report covers the 1983-84 field season and includes the status of target fish species populations in the Flathead River and tributaries, and initial work in South Bay of Flathead Lake. Additionally it addresses how Kerr operations may effect the reproduction of salmonids and northern pike. Combined trout population estimates for rainbow, brown, brook, and bull trout, averaged 13 fish/km of the lower Flathead River. The number of bull trout and cutthroat trout captured was so low that estimation of their individual populations was not possible. An interim closure to trout harvest on the lower Flathead River was recommended and approved by the Tribal Council until study results can be further analyzed and management options reviewed. Population estimates for northern pike ranged from six/kilometer in poorer habitat, to one hundred three/km in the best habitat in the main Flathead River. Seven pike were radio tagged and their movements monitored. Movements of over 89 km were recorded. One fish left the Flathead River and moved down the Clark Fork to the Plains area. Fish weirs were constructed on the Jocko River and Mission Creek to assess spawning runs of trout from the main river. Thirty-two adult rainbow passed the Jocko weir and twenty-eight passed the Mission weir during the spring spawning season. Twenty adult brown trout were captured at the Jocko weir and five at Mission weir in the fall. The Jocko weir suffered minor damage due to bed load movement during high flows of spring runoff. The structure of trout populations in the lower Flathead River points to spawning and recruitment problems caused by hydroelectric operations and sedimentation. Among the consequences of the present operational regime are constant, rapid changes in river discharge during spawning and Incubation seasons of trout species present in the lower river. Hamilton and Buell (1976) reported that similar fluctuation might exceed tolerance limits of adults and inhibit spawning behavior, dewater redds, strand fry, and displace juveniles to habitats less suitable for survival. Similar problems are felt to exist on the lower river. Constant fluctuations over backwater vegetation have been linked to major problems in successful northern pike spawning and recruitment by preventing access to spawning sites, and dewatering eggs and attached fry. Phase I of the South Bay investigation was completed this year resulting in a detailed study program for the next three years. Dominant habitat types were mapped, and physical habitat and biological monitoring methods were evaluated and selected. Permanent habitat transects, water quality stations, fish sampling, gillnetting, seining, and trapping sites were established.

Darling, James E.; Pajak, Paul; Wunderlich, Mary P.

1984-12-01T23:59:59.000Z

216

Blade System Design Study. Part II, final project report (GEC).  

DOE Green Energy (OSTI)

As part of the U.S. Department of Energy's Low Wind Speed Turbine program, Global Energy Concepts LLC (GEC)1 has studied alternative composite materials for wind turbine blades in the multi-megawatt size range. This work in one of the Blade System Design Studies (BSDS) funded through Sandia National Laboratories. The BSDS program was conducted in two phases. In the Part I BSDS, GEC assessed candidate innovations in composite materials, manufacturing processes, and structural configurations. GEC also made recommendations for testing composite coupons, details, assemblies, and blade substructures to be carried out in the Part II study (BSDS-II). The BSDS-II contract period began in May 2003, and testing was initiated in June 2004. The current report summarizes the results from the BSDS-II test program. Composite materials evaluated include carbon fiber in both pre-impregnated and vacuum-assisted resin transfer molding (VARTM) forms. Initial thin-coupon static testing included a wide range of parameters, including variation in manufacturer, fiber tow size, fabric architecture, and resin type. A smaller set of these materials and process types was also evaluated in thin-coupon fatigue testing, and in ply-drop and ply-transition panels. The majority of materials used epoxy resin, with vinyl ester (VE) resin also used for selected cases. Late in the project, testing of unidirectional fiberglass was added to provide an updated baseline against which to evaluate the carbon material performance. Numerous unidirectional carbon fabrics were considered for evaluation with VARTM infusion. All but one fabric style considered suffered either from poor infusibility or waviness of fibers combined with poor compaction. The exception was a triaxial carbon-fiberglass fabric produced by SAERTEX. This fabric became the primary choice for infused articles throughout the test program. The generally positive results obtained in this program for the SAERTEX material have led to its being used in innovative prototype blades of 9-m and 30-m length, as well as other non-wind related structures.

Griffin, Dayton A. (DNV Global Energy Concepts Inc., Seattle, WA)

2009-05-01T23:59:59.000Z

217

Enhanced Geothermal Systems (EGS) well construction technology evaluation report.  

DOE Green Energy (OSTI)

Electricity production from geothermal resources is currently based on the exploitation of hydrothermal reservoirs. Hydrothermal reservoirs possess three ingredients critical to present day commercial extraction of subsurface heat: high temperature, in-situ fluid and high permeability. Relative to the total subsurface heat resource available, hydrothermal resources are geographically and quantitatively limited. A 2006 DOE sponsored study led by MIT entitled 'The Future of Geothermal Energy' estimates the thermal resource underlying the United States at depths between 3 km and 10 km to be on the order of 14 million EJ. For comparison purposes, total U.S. energy consumption in 2005 was 100 EJ. The overwhelming majority of this resource is present in geological formations which lack either in-situ fluid, permeability or both. Economical extraction of the heat in non-hydrothermal situations is termed Enhanced or Engineered Geothermal Systems (EGS). The technologies and processes required for EGS are currently in a developmental stage. Accessing the vast thermal resource between 3 km and 10 km in particular requires a significant extension of current hydrothermal practice, where wells rarely reach 3 km in depth. This report provides an assessment of well construction technology for EGS with two primary objectives: (1) Determining the ability of existing technologies to develop EGS wells. (2) Identifying critical well construction research lines and development technologies that are likely to enhance prospects for EGS viability and improve overall economics. Towards these ends, a methodology is followed in which a case study is developed to systematically and quantitatively evaluate EGS well construction technology needs. A baseline EGS well specification is first formulated. The steps, tasks and tools involved in the construction of this prospective baseline EGS well are then explicitly defined by a geothermal drilling contractor in terms of sequence, time and cost. A task and cost based analysis of the exercise is subsequently conducted to develop a deeper understanding of the key technical and economic drivers of the well construction process. Finally, future research & development recommendations are provided and ranked based on their economic and technical significance.

Capuano, Louis, Jr. (Thermasource Inc.); Huh, Michael; Swanson, Robert (Thermasource Inc.); Raymond, David Wayne; Finger, John Travis; Mansure, Arthur James; Polsky, Yarom; Knudsen, Steven Dell

2008-12-01T23:59:59.000Z

218

Solar system installation at Louisville, Kentucky (final report)  

DOE Green Energy (OSTI)

A contract was awarded in June 1976 for the installation of a solar space heating and domestic hot water system at 2400 Watteroon Trail, Louisville, Kentucky. The overall philosophy used was to install both a liquid and a hot air system retrofitted to the existing office and combined warehouse building. The 1080 sq ft office space is heated first and excess heat is dumped into the warehouse. The two systems offered a unique opportunity to measure the performance and compare results of both air and liquid at one site. The two systems are described in detail and information on the data acquisition system is included.

Not Available

1978-08-07T23:59:59.000Z

219

Advanced turbine systems program conceptual design and product development. Task 3 -- System selection; Topical report  

Science Conference Proceedings (OSTI)

Solar Turbines Incorporated has elected to pursue an intercooled and recuperated (ICR) gas turbine system to exceed the goals of the DOE Advanced Turbine Systems (ATS) program, which are to develop and commercialize an industrial gas turbine system that operates at thermal efficiencies at least 15% higher than 1991 products, and with emissions not exceeding eight ppmv NOx and 20 ppmv CO and UHC. Solar`s goal is to develop a commercially viable industrial system (3--20 MW) driven by a gas turbine engine with a thermal efficiency of 50% (ATS50), with the flexibility to meet the differing operational requirements of various markets. Dispersed power generation is currently considered to be the primary future target market for the ICR in the 5--15 MW size class. The ICR integrated system approach provides an ideal candidate for the assumed dispersed power market, with its small footprint, easy transportability, and environmental friendliness. In comparison with other systems that use water or toxic chemicals such as ammonia for NOx control, the ICR has no consumables other than fuel and air. The low pressure ratio of the gas turbine engine also is favorable in that less parasitic power is needed to pump the natural gas into the combustor than for simple-cycle machines. Solar has narrowed the ICR configuration to two basic approaches, a 1-spool, and a 2-spool version of the ATS50. The 1-spool engine will have a lower first-cost but lower part-power efficiencies. The 2-spool ATS may not only have better part-power efficiency, its efficiency will also be less sensitive to reduced turbine rotor inlet temperature levels. Thus hot-end parts life can be increased with only small sacrifices in efficiency. The flexibility of the 2-spool arrangement in meeting customer needs is its major advantage over the 1-spool. This Task 3 Topical Report is intended to present Solar`s preliminary system selection based upon the initial trade-off studies performed to date.

White, D.J.

1994-07-01T23:59:59.000Z

220

DOE Hydrogen and Fuel Cells Program: 2010 Annual Progress Report - Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Systems Analysis Systems Analysis Printable Version 2010 Annual Progress Report VII. Systems Analysis This section of the 2010 Progress Report for the DOE Hydrogen Program focuses on systems analysis. Each technical report is available as an individual Adobe Acrobat PDF. Systems Analysis Sub-Program Overview, Fred Joseck, DOE Scenario Evaluation, Regionalization and Analysis (SERA) Model, Brian Bush, National Renewable Energy Laboratory Analysis of Energy Infrastructures and Potential Impacts from an Emergent Hydrogen Fueling Infrastructure, David Reichmuth, Sandia National Laboratories Agent-Based Model of the Transition to Hydrogen-Based Personal Transportation: Consumer Adoption and Infrastructure Development Including Combined Hydrogen, Heat, and Power, Matthew Mahalik, Argonne National

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Carlink - A Smart Carsharing System Field Test Report  

E-Print Network (OSTI)

enjoyed driving the Honda CNG Civics, and reported havingLivermore National Laboratory CNG: Compressed natural gasAt LLNL (see first page) b. CNG refueling (see first page)

Shaheen, Susan; Wright, John; Dick, David; Novick, Linda

2000-01-01T23:59:59.000Z

222

B61 System FY 2012 June Monthly Report  

SciTech Connect

These viewgraphs are to be provided to NNSA to update the status of the B61 legacy work and activities. The viewgraphs cover such issues as budget, schedule, scope, and the like. They are part of the monthly reporting process.

Wentz, Kip G. [Los Alamos National Laboratory

2012-07-09T23:59:59.000Z

223

B61 System FY 2012 May Monthly Report  

SciTech Connect

These viewgraphs are to be provided to NNSA to update the status of the B61 legacy work and activities. The viewgraphs cover such issues as budget, schedule, scope, and the like. They are part of the monthly reporting process.

Neff, Warren E [Los Alamos National Laboratory

2012-06-05T23:59:59.000Z

224

ABB SCADA/EMS System INEEL Baseline Summary Test Report (November 2004) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SCADA/EMS System INEEL Baseline Summary Test Report (November SCADA/EMS System INEEL Baseline Summary Test Report (November 2004) ABB SCADA/EMS System INEEL Baseline Summary Test Report (November 2004) This document covers the security evaluation of the "baseline" or "as delivered" system performed in the Idaho National Engineering and Environmental Laboratory (INEEL) SCADA test bed as part of the Critical Infrastructure Test Range Development Program, which is funded by the U.S. Department of Energy; Office of Energy Assurance (DOE/OEA). This report is a nonproprietary version of the report sent to ABB that identified specific issues related to the security vulnerabilities in the ABB SCADA/EMS system. Work was performed by specialists in the fields of control system development, networking, software engineering, and cybersecurity. This

225

Advanced Thermal Barrier Coating System Development. Technical progress report  

Science Conference Proceedings (OSTI)

The objectives of the program are to provide an improved TBC system with increased temperature capability and improved reliability relative to current state of the art TBC systems. The development of such a coating system is essential to the ATS engine meeting its objectives. The base program consists of three phases: Phase I: Program Planning - Complete; Phase II: Development; and Phase III: Selected Specimen - Bench Test. Work is being performed in Phase II and III of the program.

None

1999-10-15T23:59:59.000Z

226

Advanced Thermal Barrier Coating System Development. Technical progress report  

Science Conference Proceedings (OSTI)

The objectives of the program are to provide an improved TBC system with increased temperature capability and improved reliability relative to current state of the art TBC systems. The development of such a coating system is essential to the ATS engine meeting its objectives. The base program consists of three phases: Phase I: Program Planning - Complete; Phase II: Development; and Phase III: Selected Specimen - Bench Test. Work is being performed in Phase II and III of the program.

None

1998-09-21T23:59:59.000Z

227

Solar window collection and distribution module system. Final performance report  

SciTech Connect

The construction and monitoring of a solar window collection and distribution system are presented. One complete window module was purchased and assembled, including: the glass, the window frames, sealants, grills, vents and a mechanical damper device. Monitoring of the system operation was limited to measuring inside air temperature, outside air temperature, and circulation temperatures through the window module systems, as well as the actual tinted glass surface temperature. The system has produced a reduction in glare, fading of furniture, and control of solar gains to a building structure.

1985-01-01T23:59:59.000Z

228

Remote Excavation System technology evaluation report: Buried Waste Robotics Program  

SciTech Connect

This document describes the results from the Remote Excavation System demonstration and testing conducted at the Idaho National Engineering Laboratory during June and July 1993. The purpose of the demonstration was to ascertain the feasibility of the system for skimming soil and removing various types of buried waste in a safe manner and within all regulatory requirements, and to compare the performances of manual and remote operation of a backhoe. The procedures and goals of the demonstration were previously defined in The Remote Excavation System Test Plan, which served as a guideline for evaluating the various components of the system and discussed the procedures used to conduct the tests.

Not Available

1993-09-01T23:59:59.000Z

229

MARKET-BASED ADVANCED COAL POWER SYSTEMS FINAL REPORT  

NLE Websites -- All DOE Office Websites (Extended Search)

Improvements Integrated automation and data access systems are achieving lower electrical production costs through optimizing plant performance and reliability while meeting...

230

Security Controls for Computer Systems (U): Report of ...  

Science Conference Proceedings (OSTI)

... This first step is essential in order that ... other computing systems, any facilities for security ... management controls and procedures, facility clearance is ...

2013-04-15T23:59:59.000Z

231

Commercial thermal distribution systems, Final report for CIEE/CEC  

E-Print Network (OSTI)

Design." Atlanta, American Society of Heating, Refrigeration, andRefrigeration, and Air Conditioning Engineers Brake horsepower Building Management System Constant air volume Center for Environmental Design

Xu, T.

2011-01-01T23:59:59.000Z

232

Report on audit of funding for advanced radioisotope power systems  

Science Conference Proceedings (OSTI)

The U.S. Department of Energy`s (Department) Advanced Radioisotope Power Systems Program maintains the sole national capability and facilities to produce radioisotope power systems for the National Aeronautics and Space Administration (NASA), the Department of Defense, and other Federal agencies. Projects are conducted with these agencies in accordance with written agreements and are dependent on cost sharing by the user agencies. For the past seven years the program emphasis has been on providing power systems for NASA`s Cassini mission to Saturn, which was launched earlier this month. We initiated this audit to determine whether the Department received proper reimbursement from NASA for the radioisotope power systems produced.

NONE

1997-10-17T23:59:59.000Z

233

SOLERAS - Photovoltaic Power Systems Project. Rural solar applications. Final report: project summary  

Science Conference Proceedings (OSTI)

The Saudi Solar Village Project photovoltaic system is described, consisting of 160 arrays, a computerized control system, 1100 kW of electrical storage in lead-acid batteries, and an automatic weather data gathering system. Satisfactory overall system performance is reported. Performance degradation due to dust on the array lenses was determined. Field operational problems are discussed. (LEW)

Not Available

1985-01-01T23:59:59.000Z

234

From social agents to multi-agent systems: preliminary report  

Science Conference Proceedings (OSTI)

This paper presents a formal analysis of social interaction within a multi-agent system. The concept of a social agent is introduced as the elemental building block of multi-agent systems. Social agents can be individual (BDI) agents or aggregations ...

Maria Fasli

2003-06-01T23:59:59.000Z

235

Advanced thermal barrier coating system development: Technical progress report  

Science Conference Proceedings (OSTI)

Objectives are to provide an improved TBC system with increased temperature capability and improved reliability, for the Advanced Turbine Systems program (gas turbine). The base program consists of three phases: Phase I, program planning (complete); Phase II, development; and Phase III (selected specimen-bench test). Work is currently being performed in Phase II.

NONE

1996-08-07T23:59:59.000Z

236

Energy reduction analysis report for Tropicana solar process steam system  

SciTech Connect

Economic assessment data pertinent to the current Tropican solar system configuration is presented and the potential for energy reduction through the use of additional and/or larger systems is projected. The economic model, Tropicana plant and citrus juice industry energy savings potential, and industrial low-pressure steam energy savings potential are discussed. (MHR)

1978-10-01T23:59:59.000Z

237

LARGO hot water system thermal performance test report  

DOE Green Energy (OSTI)

The thermal performance tests and results on the LARGO Solar Hot Water System under natural environmental conditions are presented. Some objectives of these evaluations are to determine the amount of energy collected, the amount of energy delivered to the household as contributed by solar power supplied to operate the system and auxiliary power to maintain tank temperature at proper level, overall system efficiency and to determine temperature distribution within the tank. The tests and evaluation were performed at the Marshall Space Flight Center solar test facility. The Solar Hot Water system is termed a ''Dump-type'' because of the draining system for freeze protection. The solar collector is a single glazed flat plate. An 82-gallon domestic water heater is provided as the energy storage vessel. Water is circulated through the collector and water heater by a 5.3 GPM capacity pump, and control of the pump motor is achieved by a differential temperature controller.

Not Available

1978-11-01T23:59:59.000Z

238

Windjammer solar-water-heating system. Final technical report  

DOE Green Energy (OSTI)

The results of the Windjammer Solar-Water-Heating System tests showed that it was not as an efficient system as a comparable conventional system for converting solar energy into heat energy. However, it was determined that the innovative mode used less electric back-up energy for water heating. Reduced fossil fuel energy consumption being the ultimate objective of a solar water heating, the principle employed has been shown to be a workable energy saving concept. The differential mode of temperature control emerged as the more efficient mode of operation for the innovative system and under comparable conditions is projected to be nearly equivalent to the conventional solar system. Although the concept has proven workable, the costs feasible, and the potential for considereable improvements exists, additional research and development is needed to advance the design into its most practical application.

Windham, J.R.

1982-04-01T23:59:59.000Z

239

Packaged residential active-solar space-conditioning system. Appendix E. System performance monitoring. Final subcontract report  

Science Conference Proceedings (OSTI)

This report documents the testing of four solar space heating systems that had cost and performance characteristics equalling or exceeding competing conventional heating systems. Design concepts for these systems were solicited from the solar industry and field tested by Vitro Corporation. The designers of the four prototype systems were: Calmac Manufacturing Corporation, Contemporary Systems, Inc., Honeywell Inc., and Trident Energy Systems. Vitro Corporation reports the results of field test performance for the four packaged space heating systems. Their review presents the primary performance factors for all systems, comparing them to the best National Solar Data Network (NSDN) space heating systems. Performance factors evaluated and reported on were: collection subsystem efficiency, collector array operational efficiency, percentage of incident solar delivered to loads, collector coefficients of performance, system coefficients of performance, percent collected solar to load, and solar energy to loads/ft/sup 2/ collector/day. The data indicate that these packaged space heating systems compare well with the most recent National Solar Data Network systems.

Not Available

1986-05-01T23:59:59.000Z

240

Colloquium and Report on Systems Microbiology: Beyond Microbial Genomics  

Science Conference Proceedings (OSTI)

The American Academy of Microbiology convened a colloquium June 4-6, 2004 to confer about the scientific promise of systems microbiology. Participants discussed the power of applying a systems approach to the study of biology and to microbiology in particular, specifics about current research efforts, technical bottlenecks, requirements for data acquisition and maintenance, educational needs, and communication issues surrounding the field. A number of recommendations were made for removing barriers to progress in systems microbiology and for improving opportunities in education and collaboration. Systems biology, as a concept, is not new, but the recent explosion of genomic sequences and related data has revived interest in the field. Systems microbiology, a subset of systems biology, represents a different approach to investigating biological systems. It attempts to examine the emergent properties of microorganisms that arise from the interplay of genes, proteins, other macromolecules, small molecules, organelles, and the environment. It is these interactions, often nonlinear, that lead to the emergent properties of biological systems that are generally not tractable by traditional approaches. As a complement to the long-standing trend toward reductionism, systems microbiology seeks to treat the organism or community as a whole, integrating fundamental biological knowledge with genomics, metabolomics, and other data to create an integrated picture of how a microbial cell or community operates. Systems microbiology promises not only to shed light on the activities of microbes, but will also provide biology the tools and approaches necessary for achieving a better understanding of life and ecosystems. Microorganisms are ideal candidates for systems biology research because they are relatively easy to manipulate and because they play critical roles in health, environment, agriculture, and energy production. Potential applications of systems microbiology research range from improvements in the management of bacterial infections to the development of commercial-scale microbial hydrogen generation. A number of technical challenges must be met to realize the potential of systems microbiology. Development of a new, comprehensive systems microbiology database that would be available to the entire research community was identified as the single most critical need. Other challenges include difficulties in measuring single-cell parameters, limitations in identifying and measuring metabolites and other products, the inability to cultivate diverse microbes, limits on data accessibility, computational limitations associated with data integration, the lack of sufficient functional gene annotations, needs for quantitative proteomics, and the inapplicability of current high throughput methods to all areas of systems microbiology. Difficulties have also been encountered in acquiring the necessary data, assuring the quality of that data, and in making data available to the community in a useful format. Problems with data quality assurance and data availability could be partially offset by launching a dedicated systems microbiology database. To be of greatest value to the field, a database should include systems data from all levels of analysis, including sequences, microarray data, proteomics data, metabolite measurements, data on protein-protein or protein-nucleic interactions, carbohydrate and small RNA profiles, information on cell surface markers, and appropriate supporting data. Regular updates of these databases and adherence to agreed upon data format standards are critical to the success of these resources. It was recommended that educational requirements for undergraduate and graduate students in microbiology be amended to better prepare the next generation of researchers for the quantitative requirements of applying systems microbiology methods in their work. Systems microbiology research is too complex to be the sole property of any single academic discipline. The contributions of microbiologists, computer scientists, control th

Merry R. Buckley

2004-12-13T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Prototype solar heating and cooling systems. Monthly progress reports, April 1, 1978--June 30, 1978  

DOE Green Energy (OSTI)

This report is a collection of monthly status reports from the AiResearch Manufacturing Company, who is developing eight prototype solar heating and cooling sytems under NASA Contract NAS8-32091. This effort calls for the development, manufacture, test, system installation, maintenance, problem resolution, and performance evaluation. The systems are 3-, 25-, and 75-ton size units.

Not Available

1978-07-01T23:59:59.000Z

242

Research and Development Strategies for Compressed & Cryo-Hydrogen Storage Systems - Workshop Summary Report  

NLE Websites -- All DOE Office Websites (Extended Search)

and Development and Development Strategies for Compressed & Cryo-Hydrogen Storage Systems Workshop Summary Report Prepared by: Fuel Cell Technologies Program Compressed & Cryo-Hydrogen Storage Systems Workshops February 14-15, 2011 Crystal City, Virginia Compressed and Cryo-Hydrogen Storage Systems Workshop Summary Report 2 Research and Development Strategies for Compressed & Cryo- Hydrogen Storage Systems Summary: On February 14-15, 2011, the Systems Integration group of the National Renewable Energy Laboratory, in conjunction with the Hydrogen Storage team of the EERE Fuel Cell Technologies Program, hosted two days of workshops on compressed and cryo- hydrogen storage systems in Crystal City, VA. The overarching objective was to

243

Mobile integrated temporary utility system. Innovative technology summary report  

Science Conference Proceedings (OSTI)

The Mobile Integrated Temporary Utility System (MITUS) integrates portable electrical power along with communications and emergency alarm and lighting capabilities to provide safe, centralized power to work areas that need to be de-energized for decommissioning work. MITUS consists of a portable unit substation; up to twenty portable kiosks that house the power receptacles, communications, and emergency alarm and lighting systems; and a central communications unit. This system makes sequential decommissioning efforts efficient and cost-effective by allowing the integrated system to remain intact while being moved to subsequent work sites. Use of the MITUS also eliminates the need to conduct zero-energy tests and implement associated lock-out/tag-out procedures at partially de-energized facilities. Since the MITUS is a designed system, it can be customized to accommodate unique facility conditions simply by varying kiosks and transformer configurations. The MITUS is an attractive alternate to the use of portable generators with stand-alone communications and emergency system. It is more cost-effective than upgrading or reconfiguring existing power distribution systems.

NONE

1998-12-01T23:59:59.000Z

244

Intergovernmental Advanced Stationary PEM Fuel Cell System Demonstration Final Report  

DOE Green Energy (OSTI)

A program to complete the design, construction and demonstration of a PEMFC system fuelled by Ethanol, LPG or NG for telecom applications was initiated in October 2007. Early in the program the economics for Ethanol were shown to be unfeasible and permission was given by DOE to focus on LPG only. The design and construction of a prototype unit was completed in Jun 2009 using commercially available PEM FC stack from Ballard Power Systems. During the course of testing, the high pressure drop of the stack was shown to be problematic in terms of control and stability of the reformer. Also, due to the power requirements for air compression the overall efficiency of the system was shown to be lower than a similar system using internally developed low pressure drop FC stack. In Q3 2009, the decision was made to change to the Plug power stack and a second prototype was built and tested. Overall net efficiency was shown to be 31.5% at 3 kW output. Total output of the system is 6 kW. Using the new stack hardware, material cost reduction of 63% was achieved over the previous Alpha design. During a November 2009 review meeting Plug Power proposed and was granted permission, to demonstrate the new, commercial version of Plug Power's telecom system at CERL. As this product was also being tested as part of a DOE Topic 7A program, this part of the program was transferred to the Topic 7A program. In Q32008, the scope of work of this program was expanded to include a National Grid demonstration project of a micro-CHP system using hightemperature PEM technology. The Gensys Blue system was cleared for unattended operation, grid connection, and power generation in Aug 2009 at Union College in NY state. The system continues to operate providing power and heat to Beuth House. The system is being continually evaluated and improvements to hardware and controls will be implemented as more is learned about the system's operation. The program is instrumental in improving the efficiency and reducing costs of PEMFC based power systems using LPG fuel and continues to makes steps towards meeting DOE's targets. Plug Power would like to thank DOE for their support of this program.

Rich Chartrand

2011-08-31T23:59:59.000Z

245

Hybrid and electric advanced vehicle systems (heavy) simulation. Final report  

Science Conference Proceedings (OSTI)

A computer program to simulate hybrid and electric advanced vehicle systems (HEAVY) is described. It is intended for use early in the design process: concept evaluation, alternative comparison, preliminary design, control and management strategy development, component sizing, and sensitivity studies. It allows the designer to quickly, conveniently, and economically predict the performance of a proposed drive train. The user defines the system to be simulated using a library of predefined component models that may be connected to represent a wide variety of propulsion systems. The development of three models are discussed as examples.

Hammond, R.A.; McGehee, R.K.

1981-11-01T23:59:59.000Z

246

INTERIM VALIDATION REPORT MIDDLE DISTILLATE PRICE MONITORING SYSTEM  

E-Print Network (OSTI)

commod- the offices of Exxon ~~5T--s~::~o ~8~~~ Systems> Review items covered in Exxon, telex DWllPtion data. datedLab- the offices of Exxon Corp. , .l251 Department of

Hopelain, D.G.

2011-01-01T23:59:59.000Z

247

Improved Controls for Fusion RF Systems - Final Technical Report  

SciTech Connect

We have addressed the specific requirements for the integrated systems controlling an array of klystrons used for Lower Hybrid Current Drive (LHCD). The immediate goal for our design was to modernize the transmitter protection system (TPS) for LHCD on the Alcator C-Mod tokamak at the MIT Plasma Science and Fusion Center (MIT-PSFC). Working with the Alcator C-Mod team, we have upgraded the design of these controls to retrofit for improvements in performance and safety, as well as to facilitate the upcoming expansion from 12 to 16 klystrons. The longer range goals to generalize the designs in such a way that they will be of benefit to other programs within the international fusion effort was met by designing a system which was flexible enough to address all the MIT system requirements, and modular enough to adapt to a large variety of other requirements with minimal reconfiguration.

Jeffrey A. Casey (President, Rockfield Research Inc.)

2011-11-08T23:59:59.000Z

248

Codes, standards, and PV power systems. A 1996 status report  

SciTech Connect

As photovoltaic (PV) electrical power systems gain increasing acceptance for both off-grid and utility-interactive applications, the safety, durability, and performance of these systems gains in importance. Local and state jurisdictions in many areas of the country require that all electrical power systems be installed in compliance with the requirements of the National Electrical Code{reg_sign} (NEC{reg_sign}). Utilities and governmental agencies are now requiring that PV installations and components also meet a number of Institute of Electrical and Electronic Engineers (IEEE) standards. PV installers are working more closely with licensed electricians and electrical contractors who are familiar with existing local codes and installation practices. PV manufacturers, utilities, balance of systems manufacturers, and standards representatives have come together to address safety and code related issues for future PV installations. This paper addresses why compliance with the accepted codes and standards is needed and how it is being achieved.

Wiles, J

1996-06-01T23:59:59.000Z

249

HITIQA: an interactive question answering system a preliminary report  

Science Conference Proceedings (OSTI)

HITIQA is an interactive question answering technology designed to allow intelligence analysts and other users of information systems to pose questions in natural language and obtain relevant answers, or the assistance they require in order to perform ...

Sharon Small; Ting Liu; Nobuyuki Shimizu; Tomek Strzalkowski

2003-07-01T23:59:59.000Z

250

WRAP module 1 data management system software test report  

SciTech Connect

This document summarizes the test result information for the Data Management System (DMS). Appendix A contains test result information for all Functional Test cases and Appendix B contains the results for all the Performance Test cases.

Weidert, J.R.

1997-07-25T23:59:59.000Z

251

R and D status report. Coal Combustion Systems Division  

SciTech Connect

This report of EPRI work is concerned with the technical and economic aspects of dry sorbent injection into flue gases ahead of a fabric filter. Fly ash and the SO/sub 2/ by-product are then both collected in the baghouse. Nahcolite and trona are being tested.

Yeager, K.

1983-03-01T23:59:59.000Z

252

Search Hanford accessible reports electronically system design description. Revision 1  

SciTech Connect

The Search Hanford Accessible Records Electronically (SHARE) system was produced by a combined team of personnel from Westinghouse Hanford Company (WHC) Corrective Action Data Systems (CADS) and Information Resource Management (IRM) Information and Scientific Systems (ISS) organizations. The ESQD Text Evaluation and exchange Tool (ETEXT) prototype was used as a basis for the requirements used to support this design/build effort. TOPIC was used to build the SHARE application. TOPIC is a text search and retrieval software product produced by the Verity Corporation. The TOPIC source code is not provided with the product, and the programs cannot be changed. TOPIC can be customized for special requirements. The software is fully documented. Help messages, menu and screen layouts, command edits and options, and internal system design are all described in the TOPIC documentation. This System Design Description (SDD) will not reiterate the TOPIC documentation and design. Instead, it will focus on the SHARE installation of TOPIC. This SDD is designed to assist the SHARE database/infobase administrator (DBA) in maintaining and supporting the application. It assumes that the assigned DBA is knowledgeable in using the TOPIC product, and is also knowledgeable in using a personal computer (PC), Disk Operating System (DOS) commands, and the document WHC-CM-3-10. SHARE is an Impact Level 4 system, and all activities related to SHARE must conform with the WHC-CM-3-10 procedures for an Impact Level 4 system. The Alternatives Analysis will be treated as a level 3-Q document, to allow for reference by potential future projects.

Gilomen, T.L.

1995-12-31T23:59:59.000Z

253

Smart Infrared Inspection System Field Operational Test Final Report  

SciTech Connect

The Smart InfraRed Inspection System (SIRIS) is a tool designed to assist inspectors in determining which vehicles passing through the SIRIS system are in need of further inspection by measuring the thermal data from the wheel components. As a vehicle enters the system, infrared cameras on the road measure temperatures of the brakes, tires, and wheel bearings on both wheel ends of commercial motor vehicles (CMVs) in motion. This thermal data is then presented to enforcement personal inside of the inspection station on a user friendly interface. Vehicles that are suspected to have a violation are automatically alerted to the enforcement staff. The main goal of the SIRIS field operational test (FOT) was to collect data to evaluate the performance of the prototype system and determine the viability of such a system being used for commercial motor vehicle enforcement. From March 2010 to September 2010, ORNL facilitated the SIRIS FOT at the Greene County Inspection Station (IS) in Greeneville, Tennessee. During the course of the FOT, 413 CMVs were given a North American Standard (NAS) Level-1 inspection. Of those 413 CMVs, 384 were subjected to a SIRIS screening. A total of 36 (9.38%) of the vehicles were flagged by SIRIS as having one or more thermal issues; with brakes issues making up 33 (91.67%) of those. Of the 36 vehicles flagged as having thermal issues, 31 (86.11%) were found to have a violation and 30 (83.33%) of those vehicles were placed out-of-service (OOS). Overall the enforcement personnel who have used SIRIS for screening purposes have had positive feedback on the potential of SIRIS. With improvements in detection algorithms and stability, the system will be beneficial to the CMV enforcement community and increase overall trooper productivity by accurately identifying a higher percentage of CMVs to be placed OOS with minimal error. No future evaluation of SIRIS has been deemed necessary and specifications for a production system will soon be drafted.

Siekmann, Adam [ORNL; Capps, Gary J [ORNL; Franzese, Oscar [ORNL; Lascurain, Mary Beth [ORNL

2011-06-01T23:59:59.000Z

254

Market assessment of fuel cell total energy systems summary report  

DOE Green Energy (OSTI)

An investigation of the potential market penetration of fuel cell total energy systems (FCTES) into the nonindustrial, single building market is summarized. Nine building types, two types of construction, and the ten Department of Energy (DOE) regions were used to model the market for the time period 1985--2000. Input data developed for the penetration model included size distributions of each building type and performance and cost characteristics of FCTES and competing conventional systems. Two fuel cell systems, fuel cell - heat pump and fuel cell - central boiler and chiller, were assumed to compete with two conventional systems, electric heat pump and central chiller-boiler models. Two fuel cell supply situations were considered: (a) one in which only 40 kW(e) modules were available, and (b) one in which a catalog of 25, 40, 100, and 250 kW(e) modules were available. Data characterizing the economic climate, the intended market, and system cost and performance were used to determine the present value of life-cycle costs for each system in each market segment. Two market models were used to estimate FCTES sales. In the first, the perfect market model, FCTES sales were assumed to occur in all segments in which that system had the lowest present-valued costs. In the second, a market diffusion model was used to obtain a more probable (and lower) sales estimate than that of the perfect market model. Results are presented as FCTES sales for each market segment by FCTES module size and the effect on primary energy use by fuel type.

Mixon, W.R.; Christian, J.E.; Jackson, W.L.; Pine, G.D.; Hagler, H.; Shanker, R.; Koppelman, L.; Greenstein, D.

1979-03-01T23:59:59.000Z

255

Development of an AC Module System: Final Technical Report  

DOE Green Energy (OSTI)

The GreenRay Inc. program focused on simplifying solar electricity and making it affordable and accessible to the mainstream population. This was accomplished by integrating a solar module, micro-inverter, mounting and monitoring into a reliable, 'plug and play' AC system for residential rooftops, offering the following advantages: (1) Reduced Cost: Reduction in installation labor with fewer components, faster mounting, faster wiring. (2) Maximized Energy Production: Each AC Module operates at its maximum, reducing overall losses from shading, mismatch, or module downtime. (3) Increased Safety. Electrical and fire safety experts agree that AC Modules have significant benefits, with no energized wiring or live connections during installation, maintenance or emergency conditions. (4) Simplified PV for a Broader Group of Installers. Dramatic simplification of design and installation of a solar power system, enabling faster and more efficient delivery of the product into the market through well-established, mainstream channels. This makes solar more accessible to the public. (5) Broadened the Rooftop Market: AC Modules enable solar for many homes that have shading, split roofs, or obstructions. In addition, due to the smaller building block size of 200W vs. 1000W, homeowners with budget limitations can start small and add to their systems over time. Through this DOE program GreenRay developed the all-in-one AC Module system with an integrated PV Module and microinverter, custom residential mounting and performance monitoring. Development efforts took the product from its initial concept, through prototypes, to a commercial product sold and deployed in the residential market. This pilot deployment has demonstrated the technical effectiveness of the AC Module system in meeting the needs and solving the problems of the residential market. While more expensive than the traditional central inverter systems at the pilot scale, the economics of AC Modules become more and more favorable as the product matures and is made in high volumes. GreenRay's early customers have been highly enthusiastic about the AC Module system benefits.

Suparna Kadam; Miles Russell

2012-06-15T23:59:59.000Z

256

Confinement Vessel Assay System: Design and Implementation Report  

SciTech Connect

Los Alamos National Laboratory has a number of spherical confinement vessels remaining from tests involving nuclear materials. These vessels have an inner diameter of 6 feet with 1- to 2-inch thick steel walls. The goal of the Confinement Vessel Disposition (CVD) project is to remove debris and reduce contamination inside the vessels. We have developed a neutron assay system for the purposes of Materials Control and Accountability (MC&A) measurements of the vessel prior to and after cleanout. We present our approach to confronting the challenges in designing, building, and testing such a system. The system was designed to meet a set of functional and operational requirements. A Monte Carlo model was developed to aid in optimizing the detector design as well as to predict the systematic uncertainty associated with confinement vessel measurements. Initial testing was performed to optimize and determine various measurement parameters, and then the system was characterized using {sup 252}Cf placed a various locations throughout the measurement system. Measurements were also performed with a {sup 252}Cf source placed inside of small steel and HDPE shells to study the effect of moderation. These measurements compare favorably with their MCNPX model equivalent, making us confident that we can rely on the Monte Carlo simulation to predict the systematic uncertainty due to variations in response to material that may be localized at different points within a vessel.

Frame, Katherine C. [Los Alamos National Laboratory; Bourne, Mark M. [Los Alamos National Laboratory; Crooks, William J. [Los Alamos National Laboratory; Evans, Louise [Los Alamos National Laboratory; Mayo, Douglas R. [Los Alamos National Laboratory; Gomez, Cipriano D. [Retired CMR-OPS: OPERATIONS; Miko, David K. [Los Alamos National Laboratory; Salazar, William R. [Los Alamos National Laboratory; Stange, Sy [Los Alamos National Laboratory; Vigil, Georgiana M. [Los Alamos National Laboratory

2012-07-18T23:59:59.000Z

257

Prototype Energy Retrieval and Solar (PERS) System : Final Report.  

DOE Green Energy (OSTI)

The PERS System, which provides both heating and cooling for the substation Control House, has several different modes of operation. During the winter, heat from the transformer is recovered by a heat pump and is transferred to water circulating through a fan coil unit in the Control House forced air system. In addition, banks of tubular collectors mounted on the roof of the Control House can provide direct solar heating. During the summer, the solar collector array is used to drive a 15-ton absorption air conditioner which cools water in a 4300-gallon storage tank. Mechanical difficulaties were encountered, performance of components was not always satisfactory, and a need for modifications in the system emerged. During the winter testing period in December 1978, the heat recovery system performed with an average Coefficient of Performance (COP) of 2.75, as compared to the design goal of 4.6. The absorption chiller, however, performed quite well during the summer testing period in August, 1978. The coefficient of performance ranged from 0.598 to 0.622 on a daily basis, comparing favorably with the anticipated goal of a COP of 0.74. The overall solar-assisted absorption chiller system performed with a COP ranging from 2.80 to 3.57, with the absorption chiller functioning at even relatively low collector temperatures.

Guddat, Robert O.

1981-05-01T23:59:59.000Z

258

Metering Air Compressor Systems for Efficiency: A Progress Report  

E-Print Network (OSTI)

Air compressors have energy efficiency quantified as SCFM/BHP. However, this efficiency fluctuates over a broad range based on the loading of the compressor. When multiple compressors operate with varying loads, as in a central plant, the overall system efficiency is totally unknown. With funding from California Energy Commission under the PIER Program, we spent considerable effort over the past few years to develop system efficiency for air compressor central plants. The system efficiency was termed CASE Index, which varies from 0 to about 320, and has the units of SCF/KWH. The procedure we developed, involved metering of input (KWH) and output (SCFM), in and out of the central plant. After the initial beta testing of the procedure, as more and more compressor professionals started to use the procedure and as more metering equipments entered the picture, some metering complications were encountered. These problems were dealt with and the procedure developed under this project can produce reliable data. This paper also presents the system efficiencies we have recorded so far and the opportunities they indicate. The data shows a wide range, from a low 82 to about 250 on a 0 to 320 scale. This confirms our expectations of large energy efficiency improvement potential in compressed air systems.

Joseph, B.

2005-01-01T23:59:59.000Z

259

Confinement Vessel Assay System: Calibration and Certification Report  

SciTech Connect

Los Alamos National Laboratory has a number of spherical confinement vessels (CVs) remaining from tests involving nuclear materials. These vessels have an inner diameter of 6 feet with 1 to 2 inch thick steel walls. The goal of the Confinement Vessel Disposition (CVD) project is to remove debris and reduce contamination inside the vessels. The Confinement Vessel Assay System (CVAS) was developed to measure the amount of SNM in CVs before and after cleanout. Prior to cleanout, the system will be used to perform a verification measurement of each vessel. After cleanout, the system will be used to perform safeguards-quality assays of {le} 100-g {sup 239}Pu equivalent in a vessel for safeguards termination. The system was calibrated in three different mass regions (low, medium, and high) to cover the entire plutonium mass range that will be assayed. The low mass calibration and medium mass calibration were verified for material positioned in the center of an empty vessel. The systematic uncertainty due to position bias was estimated using an MCNPX model to simulate the response of the system to material localized at various points along the inner surface of the vessel. The background component due to cosmic ray spallation was determined by performing measurements of an empty vessel and comparing to measurements in the same location with no vessel present. The CVAS has been tested and calibrated in preparation for verification and safeguards measurements of CVs before and after cleanout.

Frame, Katherine C. [Los Alamos National Laboratory; Bourne, Mark M. [Los Alamos National Laboratory; Crooks, William J. [Los Alamos National Laboratory; Evans, Louise [Los Alamos National Laboratory; Gomez, Cipriano [Retired CMR-OPS: OPERATIONS; Mayo, Douglas R. [Los Alamos National Laboratory; Miko, David K. [Los Alamos National Laboratory; Salazar, William R. [Los Alamos National Laboratory; Stange, Sy [Los Alamos National Laboratory; Vigil, Georgiana M. [Los Alamos National Laboratory

2012-07-17T23:59:59.000Z

260

National emissions data system (NEDS) fuel use report (1977). Final report  

SciTech Connect

This report summarizes annual estimates of total consumption of major fuels such as coal, fuel oil, natural gas, gasoline, and diesel fuel. Estimates of the consumption of a number of other comparatively minor fuels are also included. The data are distributed according to major categories of air pollutant emissions sources and are reported for the nation as a whole and for individual states, territories, and the District of Columbia.

1980-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

SOLERAS Photovoltaic Power Systems Project. Interim report: module failure analysis  

Science Conference Proceedings (OSTI)

The results of the failure analysis performed during the past several months on the open circuit modules and the assessment of the feasibility of repairing these modules on site at the Solar Village are reported. Background information as related to the module failures and the effects of such failures on the overall PV field power output are provided. In addition, a plan to continue the monitoring of the rate of failure and analyzing the failure mechanisms is presented. Sandia National Laboratories conducted analyses of various solder joint problems related to the SOLERAS PV modules. Martin Marietta Corporation, the subcontractor for the SOLERAS PVPS project, performed an analysis of the cell interconnect solder joint failure. Their analyses are included in this report.

Huraib, F.S.; Imamura, M.S.; Salim, A.A.; Rao, N.

1984-10-01T23:59:59.000Z

262

Application of Storage Technology for Transmission System Support: Interim Report  

Science Conference Proceedings (OSTI)

The Electric Power Research Institute (EPRI) research in 2011 explored the potential use of battery storage to increase transmission capability in thermal limited transmission paths, an application of energy storage technology that has not been investigated in detail in prior research (see EPRI report 1024586). Researchers performed a conceptual analysis of how batteries connected at either the sending or the receiving end of a congested corridor can be used to increase the transmission capability ...

2012-12-31T23:59:59.000Z

263

PC Electronic Data Reporting Option (PEDRO) System - Patch Archive  

U.S. Energy Information Administration (EIA) Indexed Site

System - Patch Archive System - Patch Archive PEDRO Patches: Occasionally, updates to the PEDRO software are required that are not significant enough to justify a complete recreation and mailout of the software for every user. Instead, a "patch" is developed. A patch is a bundled file (or files) that are sent out to PEDRO users to update the system without completely replacing or reinstalling PEDRO. Pedro Communications Patch for All Versions - March 2007 The following process corrects the following error: Application Terminated. Error accessing external object property hostname... This error is due to some Pedro 6.2 Installation CD's that are missing a required Pedro 6.2 ActiveX component. This component allows for the connection and transfer of your Pedro 6.2 entered survey data to the EIA anonymous ftp server

264

Preliminary systems design study assessment report. Volume 7, Subsystem concepts  

SciTech Connect

The System Design Study (SDS), part of the Waste Technology Development Department at the Idaho National Engineering Laboratory (INEL), examined techniques available for the remediation of hazardous and transuranic waste stored at the Radioactive Waste Management Complex`s Subsurface Disposal Area at the INEL. Using specific technologies, system concepts for treating the buried waste and the surrounding contaminated soil were evaluated. Evaluation included implementability, effectiveness, and cost. The SDS resulted in the development of technology requirements including demonstration, testing, and evaluation activities needed for implementing each. This volume contains the descriptions and other relevant information of the four subsystems required for most of the ex situ processing systems. This volume covers the metal decontamination and sizing subsystem, soils processing subsystem, low-level waste subsystem, and retrieval subsystem.

Mayberry, J.L.; Feizollahi, F.; Del Signore, J.C.

1992-01-01T23:59:59.000Z

265

Total Energy Recovery System for Agribusiness. [Geothermally heated]. Final Report  

DOE Green Energy (OSTI)

An engineering and economic study was made to determine a practical balance of selected agribusiness subsystems resulting in realistic estimated produce yields for a geothermally heated system known as the Total Energy Recovery System for Agribusiness. The subsystem cycles for an average application at an unspecified hydrothermal resources site in the western United States utilize waste and by-products from their companion cycles insofar as practicable. Based on conservative estimates of current controlled environment yields, produce wholesale market prices, production costs, and capital investment required, it appears that the family-operation-sized TERSA module presents the potential for marginal recovery of all capital investment costs. In addition to family- or small-cooperative-farming groups, TERSA has potential users in food-oriented corporations and large-cooperative-agribusiness operations. The following topics are considered in detail: greenhouse tomatoes and cucumbers; fish farming; mushroom culture; biogas generation; integration methodology; hydrothermal fluids and heat exchanger selection; and the system. 133 references. (MHR)

Fogleman, S.F.; Fisher, L.A.; Black, A.R.; Singh, D.P.

1977-05-01T23:59:59.000Z

266

General theme report: Working session 2, Solar thermal systems  

DOE Green Energy (OSTI)

Currently, over 90% of the world's large-scale solar electric energy is generated with concentrating solar thermal power plants. Such plants have the potential to meet many of the world's future energy needs. Research efforts are generally focused on generating electricity, though a variety of other applications are being pursued. Today, the technology for using solar thermal energy is well developed, cost competitive, and in many cases, ready for widespread application. The current state of each of the solar thermal technologies and their applications is reviewed, and recommendations for increasing their use are presented. The technologies reviewed in detail are: parabolic trough systems, central tower systems, and parabolic dish systems. 20 refs., 1 fig., 1 tab.

Alpert, D.J.; Kolb, G.J.

1991-01-01T23:59:59.000Z

267

Analysis of batteries for use in photovoltaic systems. Final report  

SciTech Connect

An evaluation of 11 types of secondary batteries for energy storage in photovoltaic electric power systems is given. The evaluation was based on six specific application scenarios which were selected to represent the diverse requirements of various photovoltaic systems. Electrical load characteristics and solar insulation data were first obtained for each application scenario. A computer-based simulation program, SOLSIM, was then developed to determine optimal sizes for battery, solar array, and power conditioning systems. Projected service lives and battery costs were used to estimate life-cycle costs for each candidate battery type. The evaluation considered battery life-cycle cost, safety and health effects associated with battery operation, and reliability/maintainability. The 11 battery types were: lead-acid, nickel-zinc, nickel-iron, nickel-hydrogen, lithium-iron sulfide, calcium-iron sulfide, sodium-sulfur, zinc-chlorine, zinc-bromine, Redox, and zinc-ferricyanide. The six application scenarios were: (1) a single-family house in Denver, Colorado (photovoltaic system connected to the utility line); (2) a remote village in equatorial Africa (stand-alone power system); (3) a dairy farm in Howard County, Maryland (onsite generator for backup power); (4) a 50,000 square foot office building in Washington, DC (onsite generator backup); (5) a community in central Arizona with a population of 10,000 (battery to be used for dedicated energy storage for a utility grid-connected photovoltaic power plant); and (6) a military field telephone office with a constant 300 W load (trailer-mounted auxiliary generator backup). Recommendations for a research and development program on battery energy storage for photovoltaic applications are given, and a discussion of electrical interfacing problems for utility line-connected photovoltaic power systems is included. (WHK)

Podder, A.; Kapner, M.

1981-02-01T23:59:59.000Z

268

ADVANCED TURBINE SYSTEM CONCEPTUAL DESIGN AND PRODUCT DEVELOPMENT - Final Report  

SciTech Connect

Asea Brown Boveri (ABB) has completed its technology based program. The results developed under Work Breakdown Structure (WBS) 8, concentrated on technology development and demonstration have been partially implemented in newer turbine designs. A significant improvement in heat rate and power output has been demonstrated. ABB will use the knowledge gained to further improve the efficiency of its Advanced Cycle System, which has been developed and introduced into the marked out side ABB's Advanced Turbine System (ATS) activities. The technology will lead to a power plant design that meets the ATS performance goals of over 60% plant efficiency, decreased electricity costs to consumers and lowest emissions.

Albrecht H. Mayer

2000-07-15T23:59:59.000Z

269

Hanford Site Emergency Alerting System siren testing report  

Science Conference Proceedings (OSTI)

The purpose of the test was to determine the effective coverage of the proposed upgrades to the existing Hanford Site Emergency Alerting System (HSEAS). The upgrades are to enhance the existing HSEAS along the Columbia River from the Vernita Bridge to the White Bluffs Boat Launch as well as install a new alerting system in the 400 Area on the Hanford Site. Five siren sites along the Columbia River and two sites in the 400 Area were tested to determine the site locations that will provide the desired coverage.

Weidner, L.B.

1997-08-13T23:59:59.000Z

270

Commercialization analysis of large wind energy conversion systems. Final report  

DOE Green Energy (OSTI)

The framework is described that can be used to evaluate potential new federal incentives to facilitate the market acceptance of utility-scale wind energy conversion systems. The insights gained from utilizing this framework to evaluate a variety of hypothetical federal incentives are discussed. The heart of the evaluation framework is an explicit representation of the decisions made by utility purchasers, suppliers, and government agencies with respect to the utilization and fabrication of large wind energy conversion systems. The demand-side and supply-side aspects of the multiparty commercialization model are described, and the model's struture is explained. (LEW)

Boyd, D.W.; Buckley, O.E.; Haas, S.M.

1980-06-01T23:59:59.000Z

271

Surface moisture measurement system hardware acceptance test report  

SciTech Connect

This document summarizes the results of the hardware acceptance test for the Surface Moisture Measurement System (SMMS). This test verified that the mechanical and electrical features of the SMMS functioned as designed and that the unit is ready for field service. The bulk of hardware testing was performed at the 306E Facility in the 300 Area and the Fuels and Materials Examination Facility in the 400 Area. The SMMS was developed primarily in support of Tank Waste Remediation System (TWRS) Safety Programs for moisture measurement in organic and ferrocyanide watch list tanks.

Ritter, G.A., Westinghouse Hanford

1996-05-28T23:59:59.000Z

272

ADVANCED TURBINE SYSTEM CONCEPTUAL DESIGN AND PRODUCT DEVELOPMENT - Final Report  

SciTech Connect

Asea Brown Boveri (ABB) has completed its technology based program. The results developed under Work Breakdown Structure (WBS) 8, concentrated on technology development and demonstration have been partially implemented in newer turbine designs. A significant improvement in heat rate and power output has been demonstrated. ABB will use the knowledge gained to further improve the efficiency of its Advanced Cycle System, which has been developed and introduced into the marked out side ABB's Advanced Turbine System (ATS) activities. The technology will lead to a power plant design that meets the ATS performance goals of over 60% plant efficiency, decreased electricity costs to consumers and lowest emissions.

Albrecht H. Mayer

2000-07-15T23:59:59.000Z

273

Underground home A/C system. Final report  

DOE Green Energy (OSTI)

The purpose of the project was to transfer the heat of house air into the earth through an underground piping system, return the cooler to the house and disperse it throughout the house. The principle of the idea has been achieved, but not to the extent desired. It was originally hoped that the system would allow temperatures in the house to reach a maximum of 80/sup 0/ even during days where outside temperatures reached high 90/sup 0/. So far, a differential of 6/sup 0/ to 8/sup 0/ has been achieved.

Outland, B.W.

1981-06-30T23:59:59.000Z

274

Solar powered desiccant air conditioning system. Final report  

DOE Green Energy (OSTI)

A solar-powered desiccant air conditioning system using silica gel has been developed, and modifications to the existing unit and additional testing are proposed to demonstrate the feasibility of the unit. Conversion from a rotating bed to a fixed bed of silica gel is proposed. Some general plans for commercialization are briefly discussed. (LEW)

Not Available

1981-07-24T23:59:59.000Z

275

FY 2005 Quantum Cascade Laser Alignment System Final Report  

Science Conference Proceedings (OSTI)

The Alignment Lasers Task of Pacific Northwest National Laboratory's (PNNL's) Remote Spectroscopy Project (Project PL211I) is a co-funded project between DOE NA-22 and a Classified Client. This project, which began in the second half of FY03, involved building and delivering a Quantum Cascade (QC) Laser Alignment System to be used for testing the pupil alignment of an infrared sensor by measuring the response from four pairs of diametrically opposed QC lasers. PNNL delivered the system in FY04 and provided technical assistance in FY05 culminating into a successful demonstration of the system. This project evolved from the Laser Development Task of PL211I, which is involved in developing novel laser technology to support development of advanced chemical sensors for detecting the proliferation of nuclear weapons. The laser systems are based on quantum cascade (QC) lasers, a new semiconductor source in the infrared. QC lasers can be tailored to emit light throughout the infrared region (3.5 ? 17 ?m) and have high output power and stability. Thus, these lasers provide an infrared source with superb power and spectral stability enabling them to be used for applications such as alignment and calibration in addition to chemical sensing.

Myers, Tanya L.; Cannon, Bret D.; Wojcik, Michael D.; Broocks, Bryan T.; Stewart, Timothy L.; Hatchell, Brian K.

2006-01-11T23:59:59.000Z

276

Solar heating system installed at Stamford, CT. Final report  

DOE Green Energy (OSTI)

Information is provided on the solar heating system installed at the Lutz-Sotire Partnership Executive East Office Building, Stamford, Connecticut. The information consists of description of system and components, operation and maintenance manual, as-built drawings and manufacturer's component data. The solar system was designed to provide approximately 50 percent of the heating requirements. The solar facility has 2,561 sq. ft. of liquid flat plate collectors and a 6000 gallon, stone lined, well-insulated storage tank. Freeze protection is provided by a 50 percent glycol/water mixture in the collector loop. From the storage tank, solar heated water is fed into the building's distributed heat pump loop via a modulating three-way valve. If the storage tank temperature drops below 80/sup 0/F, the building loop may be supplied from the existing electrical hot water boilers. The Executive East Office Building is of moderate size, 25,000 sq. ft. of heated space in 2 1/2 stories. The solar system makes available for other users up to 150 KVA of existing electrical generating capacity.

Not Available

1979-09-01T23:59:59.000Z

277

Solar heating and cooling systems design and development: quarterly report  

DOE Green Energy (OSTI)

This program calls for the development and delivery of eight prototype solar heating and cooling systems for installation and operational test. Two heating and six heating and cooling units will be delivered for single-family residences, multiple-family residences and commercial applications. This document describes the progress of the program during the fifth program quarter, 1 July 1977 to 30 September 1977.

Not Available

1977-11-11T23:59:59.000Z

278

Solar heating and cooling systems design and development: quarterly report  

DOE Green Energy (OSTI)

The progress of the program for the development and delivery of eight prototype solar heating and cooling systems for installation and operational test is described for the period, 1 January 1978 through 31 March 1978. Two heating and six heating and cooling units will be delivered for single-family residences, multiple-family residences, and commercial applications.

Not Available

1978-07-01T23:59:59.000Z

279

Construction Summary and As-Built Report for Ground Water Treatment System  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Construction Summary and As-Built Report for Ground Water Treatment Construction Summary and As-Built Report for Ground Water Treatment System Monticello, Utah, Permeable Reactive Barrier Site Construction Summary and As-Built Report for Ground Water Treatment System Monticello, Utah, Permeable Reactive Barrier Site Construction Summary and As-Built Report for Ground Water Treatment System Monticello, Utah, Permeable Reactive Barrier Site Construction Summary and As-Built Report for Ground Water Treatment System Monticello, Utah, Permeable Reactive Barrier Site More Documents & Publications Dispersivity Testing of Zero-Valent Iron Treatment Cells: Monticello, Utah, November 2005 Through February 2008 Third (March 2006) Coring and Analysis of Zero-Valent Iron Permeable Reactive Barrier, Monticello, Utah Performance Assessment and Recommendations for Rejuvenation of a Permeable

280

U.S. - Canada Power System Outage Task Force: Final Report on the  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

- Canada Power System Outage Task Force: Final Report on the - Canada Power System Outage Task Force: Final Report on the Implementation of Task Force Recommendations U.S. - Canada Power System Outage Task Force: Final Report on the Implementation of Task Force Recommendations On August 14, 2003, the largest power blackout in North American history affected an area with an estimated 50 million people and 61,800 megawatts (MW) of electric load in the states of Ohio, Michigan, Pennsylvania, New York, Vermont, Massachusetts, Connecticut and New Jersey, and the Canadian province of Ontario. U.S. - Canada Power System Outage Task Force: Final Report on the Implementation of Task Force Recommendations More Documents & Publications Blackout 2003: Blackout Final Implementation Report Blackout 2003: The August 14, 2003 Blackout One Year Later: Actions Taken

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Ris-R-Report Energy Systems Analysis of Waste to Energy  

E-Print Network (OSTI)

Risø-R-Report Energy Systems Analysis of Waste to Energy Technologies by use of EnergyPLAN Marie Münster Risø-R-1667(EN) April 2009 #12;Author: Marie Münster Title: Energy Systems Analysis of Waste to Energy Technologies by use of EnergyPLAN Division: Systems Analysis Division Risø-R-1667(EN) April 2009

282

Develop a field grid system for yield mapping and machine control. Final report, Invention 544  

SciTech Connect

The objective of this project was to build and test the Field Grid Sense system for yield mapping and machine control during harvesting. Secondly, to use Field Grid Sense system with chemical application equipment to demonstrate a workable in-field system. This document contains summarized quarterly reports.

1995-12-15T23:59:59.000Z

283

DOE uniform reporting system for Federal assistance (grants and cooperative agreements): guidelines  

SciTech Connect

These guidelines establish a uniform reporting system (URS) for grants and cooperative agreements. The purpose is to simplify reporting requirements, standardize reporting, and ensure that no assistance recipient submits more reports than needed to achieve accountability for public funds. This system replaces the many reporting procedures previously imposed by DOE component organizations. Uniform terminology and data elements will minimize ambiguity of meaning and intent. A glossary of terms is provided. A checklist is used to identify all reporting requirements at the time of award. The recipient is encouraged to discuss the requirements before the time of award in order to ensure that they are appropriate. The Guidelines describe planning forms which can be included in the Federal assistance application or proposal to present the planned approach and desired results. Flexibility has been built into the system to ensure that the information requested is relative to the activity performed. A recipient of Federal assistance submits information only once in each reporting period. The reporting system provides recipients with a formal method for identifying problems, including those originated by the Federal government. For purposes of illustration, a hypothetical project - partially funded by DOE under a cooperative agreement - using all the Program Management forms is presented in Part II, Program Management. Part III, Technical Information uses a research grant to illustrate Technical Reporting. Appendix B provides a complete example of the reporting requirements on a research grant.

Not Available

1981-04-01T23:59:59.000Z

284

Fate of Mercury in FGD Systems: Second Interim Report  

Science Conference Proceedings (OSTI)

This report describes the results of laboratory investigations of the fate of flue gas mercury species in wet flue gas desulfurization (FGD) absorbers that are used for SO2 control in coal-fired power plants. The laboratory investigations were conducted in the latter half of 2004 and in early 2005, and include bench-scale simulations of wet FGD absorbers under a range of operating conditions and fundamental investigations of the kinetics of mercury reactions in FGD liquors. Data collected in the EPA merc...

2005-03-14T23:59:59.000Z

285

Guidelines for reporting parabolic trough solar electric system performance  

DOE Green Energy (OSTI)

The purpose of this activity is to develop a generic methodology which can be used to track and compare the performance of parabolic trough power plants. The approach needs to be general enough to work for all existing and future parabolic trough plant designs, provide meaningful comparisons of year to year performance, and allow for comparisons between dissimilar plant designs. The approach presented here uses the net annual system efficiency as the primary metric for evaluating the performance of parabolic trough power plants. However, given the complex nature of large parabolic trough plants, the net annual system efficiency by itself does not adequately characterize the performance of the plant. The approach taken here is to define a number of additional performance metrics which enable a more comprehensive understanding of overall plant performance.

Price, H.W.

1997-06-01T23:59:59.000Z

286

Energy implications of integrated solid waste management systems. Final report  

DOE Green Energy (OSTI)

This study develops estimates of energy use and recovery from managing municipal solid waste (MSW) under various collection, processing, and disposal scenarios. We estimate use and recovery -- or energy balance -- resulting from MSW management activities such as waste collection, transport, processing, and disposal, as well as indirect use and recovery linked to secondary materials manufacturing using recycled materials. In our analysis, secondary materials manufacturing displaces virgin materials manufacturing for 13 representative products. Energy implications are expressed as coefficients that measure the net energy saving (or use) of displacing products made from virgin versus recycled materials. Using data developed for the 1992 New York City Master Plan as a starting point, we apply our method to an analysis of various collection systems and 30 types of facilities to illustrate bow energy balances shift as management systems are modified. In sum, all four scenarios show a positive energy balance indicating the energy and advantage of integrated systems versus reliance on one or few technology options. That is, energy produced or saved exceeds the energy used to operate the solid waste system. The largest energy use impacts are attributable to processing, including materials separation and composting. Collection and transportation energy are relatively minor contributors. The largest two contributors to net energy savings are waste combustion and energy saved by processing recycled versus virgin materials. An accompanying spatial analysis methodology allocates energy use and recovery to New York City, New York State outside the city, the U.S., and outside the U.S. Our analytical approach is embodied in a spreadsheet model that can be used by energy and solid waste analysts to estimate impacts of management scenarios at the state and substate level.

Little, R.E.; McClain, G.; Becker, M.; Ligon, P.; Shapiro, K.

1994-07-01T23:59:59.000Z

287

Solar heating and cooling systems design and development quarterly report  

DOE Green Energy (OSTI)

The program calls for the development and delivery of eight (was 12) prototype solar heating and cooling systems for installation and operational test. Two (was 6) heating and six heating and cooling units will be delivered for single-family residences (SFR), multiple-family residences (MFR) and commercial applications. This document describes the progress of the program during the eighth program quarter, 1 April 1978 to 30 June 1978.

Not Available

1978-07-01T23:59:59.000Z

288

Standard-B hydrogen monitoring system acceptance test report  

DOE Green Energy (OSTI)

Test Engineering was supported by Tank Waste Remediation System Safety Programs Engineering Support in the performance of an Acceptance Test Procedure (ATP) to qualify the Standard Hydrogen Monitoring System (SHMS) cabinet installed on waste tank 241-SY-103. The June 7, 1994 ATP performance was controlled by West Waste Tank Farms work package 2W-94-322. The ATP was conducted following the final installation of a second Whittaker electro-chemical hydrogen monitoring cell. The cabinet had been sited on the waste tank two years earlier, but never connected to the exhaust vent header to monitor Tank 241-SY-103 vent header exhaust gases. The cabinet was then modified, to remove two undesirable solid state hydrogen monitors and install a second Whittaker electro-chemical hydrogen monitoring sensor and signal conditioning. The ATP was used to assure that the cabinet wiring and components were properly installed and labeled and that the two years without operation had not seriously damaged the installed equipment. Electrical and pneumatic tests were performed to assure system integrity.

Tran, T.T.

1994-09-08T23:59:59.000Z

289

Evaluation of integrated wall systems incorporating electrochromic windows [Final report  

SciTech Connect

Billions of dollars are spent annually in the U.S. on energy lost through the use of inefficient windows. Even wall systems with advanced static glazings and moveable shading devices are not optimal because they can't effectively respond to changing solar conditions. Electrochromic (EC) smart windows can dynamically control the amount of solar light and heat entering a building. The energy saving performance of fully dynamic wall systems containing EC windows was compared with that of static systems using the DOE 2.1E building simulation program. Total costs for different scenarios were computed. SAGE demonstrated the capability to produce double pane EC windows in which the transmittance repeatedly varied between 2-58%. Relative impact of EC glazings in buildings compared to static is 10-20% energy savings across all climatic regions investigated. Significant life cycle cost savings are predicted for SAGE's EC windows when compared to conventional solar control windows over an estimated product lifetime of 20 years.

Sbar, Neil L.

2001-03-30T23:59:59.000Z

290

Shale-oil-recovery systems incorporating ore beneficiation. Final report.  

SciTech Connect

This study analyzed the recovery of oil from oil shale by use of proposed systems which incorporate beneficiation of the shale ore (that is concentration of the kerogen before the oil-recovery step). The objective was to identify systems which could be more attractive than conventional surface retorting of ore. No experimental work was carried out. The systems analyzed consisted of beneficiation methods which could increase kerogen concentrations by at least four-fold. Potentially attractive low-enrichment methods such as density separation were not examined. The technical alternatives considered were bounded by the secondary crusher as input and raw shale oil as output. A sequence of ball milling, froth flotation, and retorting concentrate is not attractive for Western shales compared to conventional ore retorting; transporting the concentrate to another location for retorting reduces air emissions in the ore region but cost reduction is questionable. The high capital and energy cost s results largely from the ball milling step which is very inefficient. Major improvements in comminution seem achievable through research and such improvements, plus confirmation of other assumptions, could make high-enrichment beneficiation competitive with conventional processing. 27 figures, 23 tables.

Weiss, M.A.; Klumpar, I.V.; Peterson, C.R.; Ring, T.A.

1982-10-01T23:59:59.000Z

291

New vision solar system mission study. Final report  

Science Conference Proceedings (OSTI)

The vision for the future of the planetary exploration program includes the capability to deliver {open_quotes}constellations{close_quotes} or {open_quotes}fleets{close_quotes} of microspacecraft to a planetary destination. These fleets will act in a coordinated manner to gather science data from a variety of locations on or around the target body, thus providing detailed, global coverage without requiring development of a single large, complex and costly spacecraft. Such constellations of spacecraft, coupled with advanced information processing and visualization techniques and high-rate communications, could provide the basis for development of a {open_quotes}virtual{close_quotes} {open_quotes}presence{close_quotes} in the solar system. A goal could be the near real-time delivery of planetary images and video to a wide variety of users in the general public and the science community. This will be a major step in making the solar system accessible to the public and will help make solar system exploration a part of the human experience on Earth.

Mondt, J.F.; Zubrin, R.M.

1996-03-01T23:59:59.000Z

292

Shale oil production system reference case study. Final report  

DOE Green Energy (OSTI)

Material balances, utility balances, and overall processing schemes were developed for two reference shale oil production systems. For both cases, crushed and sized oil shale is fed into a mix of surface retorts specified for this study, which handle both coarse and fine ore. Case 1A produces an upgraded crude product suitable for refinery feedstock, and Case 1B produces a crude shale oil. The reference system uses room-and-pillar mining, three different types of retorts not unlike those proposed for the White River Shale Project on Federal Lease Tracts U-a and U-b, a straightforward upgrading of the raw shale oil to a refinery feedstock syncrude, and pipeline transportation of that product. In addition to the production of an upgraded product, there is also a modified system for producing raw shale oil that is minimally upgraded for pipeline transportation purposes. The capital cost estimate for the two reference cases has 26 cost elements, excluding, for example, any land or finance costs. A more complete list of excluded cost elements is provided in Section VII. The two distinct cases, production of raw and upgraded shale oil, were included to avoid foreclosing the issue of on- or off-site upgrading. The difference in estimated capital cost ($795M vs. $875M) amounts to about 10 percent.

Not Available

1979-06-01T23:59:59.000Z

293

Evaluation of integrated wall systems incorporating electrochromic windows [Final report  

DOE Green Energy (OSTI)

Billions of dollars are spent annually in the U.S. on energy lost through the use of inefficient windows. Even wall systems with advanced static glazings and moveable shading devices are not optimal because they can't effectively respond to changing solar conditions. Electrochromic (EC) smart windows can dynamically control the amount of solar light and heat entering a building. The energy saving performance of fully dynamic wall systems containing EC windows was compared with that of static systems using the DOE 2.1E building simulation program. Total costs for different scenarios were computed. SAGE demonstrated the capability to produce double pane EC windows in which the transmittance repeatedly varied between 2-58%. Relative impact of EC glazings in buildings compared to static is 10-20% energy savings across all climatic regions investigated. Significant life cycle cost savings are predicted for SAGE's EC windows when compared to conventional solar control windows over an estimated product lifetime of 20 years.

Sbar, Neil L.

2001-03-30T23:59:59.000Z

294

Mission analysis of photovoltaic solar energy systems. Final report. Volume II. Technical report  

DOE Green Energy (OSTI)

Appendices include (1) demand forecasting methodologies, (2) system simulation model, (3) preliminary investigation of residential use of dc power, (4) power plant economic model, and (5) projections of unit fuel prices to the year 2000. (WHK)

Not Available

1975-12-01T23:59:59.000Z

295

DOE Hydrogen and Fuel Cells Program: 2009 Annual Progress Report - Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Systems Analysis Systems Analysis Printable Version 2009 Annual Progress Report VII. Systems Analysis This section of the 2009 Progress Report for the DOE Hydrogen Program focuses on systems analysis. Each technical report is available as an individual Adobe Acrobat PDF. Download Adobe Reader. Systems Analysis Program Element Introduction, Fred Joseck, U.S. Department of Energy (PDF 411 KB) HyDRA: Hydrogen Demand and Resource Analysis Tool (PDF 243 KB), Johanna Levene, National Renewable Energy Laboratory Water Needs and Constraints for Hydrogen Pathways (PDF 99 KB), A.J. Simon, Lawrence Livermore National Laboratory Cost Implications of Hydrogen Quality Requirements (PDF 817 KB), Shabbir Ahmed, Argonne National Laboratory Macro-System Model (PDF 384 KB), Mark Ruth, National Renewable

296

Plate-Based Fuel Processing System Final Report  

DOE Green Energy (OSTI)

On-board reforming of liquid fuels into hydrogen is an enabling technology that could accelerate consumer usage of fuel cell powered vehicles. The technology would leverage the convenience of the existing gasoline fueling infrastructure while taking advantage of the fuel cell efficiency and low emissions. Commercial acceptance of on-board reforming faces several obstacles that include: (1) startup time, (2) transient response, and (3) system complexity (size, weight and cost). These obstacles are being addressed in a variety of projects through development, integration and optimization of existing fuel processing system designs. In this project, CESI investigated steam reforming (SR), water-gas-shift (WGS) and preferential oxidation (PrOx) catalysts while developing plate reactor designs and hardware where the catalytic function is integrated into a primary surface heat exchanger. The plate reactor approach has several advantages. The separation of the reforming and combustion streams permits the reforming reaction to be conducted at a higher pressure than the combustion reaction, thereby avoiding costly gas compression for combustion. The separation of the two streams also prevents the dilution of the reformate stream by the combustion air. The advantages of the plate reactor are not limited to steam reforming applications. In a WGS or PrOx reaction, the non-catalytic side of the plate would act as a heat exchanger to remove the heat generated by the exothermic WGS or PrOx reactions. This would maintain the catalyst under nearly isothermal conditions whereby the catalyst would operate at its optimal temperature. Furthermore, the plate design approach results in a low pressure drop, rapid transient capable and attrition-resistant reactor. These qualities are valued in any application, be it on-board or stationary fuel processing, since they reduce parasitic losses, increase over-all system efficiency and help perpetuate catalyst durability. In this program, CESI took the initial steam reforming plate-reactor concept and advanced it towards an integrated fuel processing system. A substantial amount of modeling was performed to guide the catalyst development and prototype hardware design and fabrication efforts. The plate-reactor mechanical design was studied in detail to establish design guidelines which would help the plate reactor survive the stresses of repeated thermal cycles (from start-ups and shut-downs). Integrated system performance modeling was performed to predict system efficiencies and determine the parameters with the most significant impact on efficiency. In conjunction with the modeling effort, a significant effort was directed towards catalyst development. CESI developed a highly active, sulfur tolerant, coke resistant, precious metal based reforming catalyst. CESI also developed its own non-precious metal based water-gas shift catalyst and demonstrated the catalysts durability over several thousands of hours of testing. CESI also developed a unique preferential oxidation catalyst capable of reducing 1% CO to < 10 ppm CO over a 35 C operating window through a single pass plate-based reactor. Finally, CESI combined the modeling results and steam reforming catalyst development efforts into prototype hardware. The first generation 3kW(e) prototype was fabricated from existing heat-exchanger plates to expedite the fabrication process. This prototype demonstrated steady state operation ranging from 5 to 100% load conditions. The prototype also demonstrated a 20:1 turndown ratio, 10:1 load transient operation and rapid start-up capability.

Carlos Faz; Helen Liu; Jacques Nicole; David Yee

2005-12-22T23:59:59.000Z

297

Advanced high performance steam systems for industrial cogeneration: Final report  

SciTech Connect

Advanced steam conditions of 1500/sup 0/F and 1500 psig have been shown to offer a major positive economic impact and a dramatic improvement in cogeneration system performance. In a back pressure steam turbine system, electricity production increases by 80%, and the return on investment improves by 60%. For a 35% extraction turbine, the electricity production increases 28% and the return increases by 34%. Designs of a 1500/sup 0/F modular steam generator and two sizes of matching steam turbines have been completed. The steam generator module uses all Alloy 800 tubes except for two superheater rows of Inconel 617. Its design is based on current production Alloy 800 once-through steam generators currently being introduced into cogeneration combined cycles. A test loop is currently evaluating candidate steam generator tube materials and steam turbine materials at 1500/sup 0/F and 1500 psig. To date, 4000 hours of operation of this loop have been accumulated. The candidate metals after operation in 1500/sup 0/F and 1500 psig steam showed no surface distress. Trade-off studies have been completed on the high temperature steam turbine. Tangential, radial, and axial turbine configurations have been designed and evaluated. The stress analyses of the 1500/sup 0/F steam turbines show that the machine can be operated at 1500/sup 0/F and 1500 psig for over ten years without component replacement when using rotor hub cooling to maintain disk bore temperatures in the 900/sup 0/F range. When applied in back pressure steam, extraction steam, and combined cycle systems the ''1500/sup 0/F steam technology building blocks'' provide full coverage of industrial cogeneration from 4 MW to 25 MW in a single gas turbine and steam turbine installation. A twelve-inch diameter tangential flow turbine has also been designed which is optimum in the 1 to 3 MW power range.

Duffy, T.E.; Schneider, P.H.; Campbell, A.H.; Evensen, O.E.

1987-01-01T23:59:59.000Z

298

Nickel-iron battery system safety. Final report  

DOE Green Energy (OSTI)

Eagle-Picher Industries conducted a literature search and experimental tests to characterize the generated flow rates of gaseous hydrogen (GH/sub 2/) and gaseous oxygen (GO/sub 2/) from an electrical vehicle (EV) nickel-iron battery system. The resulting gassing rates were used to experimentally evaluate the flame quenching capabilities of several candidate devices to prevent the propagation of flame within batteries having central watering/venting systems. The battery generated hydrogen (GH/sub 2/) and oxygen (GO/sub 2/) gasses were measured for a complete charge and discharge cycle. The data correlates well with accepted theory during strong overcharge conditions indicating that the measurements are valid for other portions of the cycle. Tests have confirmed that the gas mixture in the cells is always flammable regardless of the battery status. Research of flame arrestor literature yielded little information regarding their operation with hydrogen-oxygen mixtures. It was indicated that a conventional flame arrestor would not be effective over the broad spectrum of gassing conditions presented by a nickel-iron battery. Four different types of protective devices were evaluated. A foam-metal arrestor design was successful in quenching GH/sub 2/-GO/sub 2/ flames, however; the application of this flame arrestor to individual cell or module protection in a battery is problematic. A possible rearrangement of the watering/venting system to accept the partial protection of simple one-way valves is presented. This in combination with the successful foam-metal arrestor as main vent protection, could result in a significant improvement in battery protection. This concept was not tested.

Saltat, R.

1984-06-01T23:59:59.000Z

299

Coal-fired high performance power generating system. Final report  

SciTech Connect

As a result of the investigations carried out during Phase 1 of the Engineering Development of Coal-Fired High-Performance Power Generation Systems (Combustion 2000), the UTRC-led Combustion 2000 Team is recommending the development of an advanced high performance power generation system (HIPPS) whose high efficiency and minimal pollutant emissions will enable the US to use its abundant coal resources to satisfy current and future demand for electric power. The high efficiency of the power plant, which is the key to minimizing the environmental impact of coal, can only be achieved using a modern gas turbine system. Minimization of emissions can be achieved by combustor design, and advanced air pollution control devices. The commercial plant design described herein is a combined cycle using either a frame-type gas turbine or an intercooled aeroderivative with clean air as the working fluid. The air is heated by a coal-fired high temperature advanced furnace (HITAF). The best performance from the cycle is achieved by using a modern aeroderivative gas turbine, such as the intercooled FT4000. A simplified schematic is shown. In the UTRC HIPPS, the conversion efficiency for the heavy frame gas turbine version will be 47.4% (HHV) compared to the approximately 35% that is achieved in conventional coal-fired plants. This cycle is based on a gas turbine operating at turbine inlet temperatures approaching 2,500 F. Using an aeroderivative type gas turbine, efficiencies of over 49% could be realized in advanced cycle configuration (Humid Air Turbine, or HAT). Performance of these power plants is given in a table.

1995-08-31T23:59:59.000Z

300

On-farm biogas systems information dissemination project. Final report  

SciTech Connect

The purpose of this project was to study how farmers manage anaerobic digesters on three New York State dairy farms. Two years of data collected were from both plug-flow and tower-type mixed-flow digesters at regular intervals over a three-year period revealed that the financial return from the energy produced by a biogass system in the late 1980`s is marginal. Little difficulty was experienced in operation of the anaerobic digester; however, several farms utilizing congeneration to convert biogas into electricity and heat suffered from not applying maintenance to the congenerator in a timely fashion.

Campbell, J.K.; Koelsch, R.K.; Guest, R.W.; Fabian, E.

1997-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Minimizing Failures While Maintaining Efficiency of Complex Interactive Networks and Systems: EPRI/DoD Complex Interactive Networks/ Systems Initiative; First Annual Report  

Science Conference Proceedings (OSTI)

This is the first annual report from the EPRI/DOD Complex Interactive Networks/Systems Initiative. The report describes research progress in minimizing failures while maintaining efficiency of complex interactive networks and systems.

2000-05-26T23:59:59.000Z

302

Generic Disposal System Modeling--Fiscal Year 2011 Progress Report  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

12/2011 12/2011 Rev. 2 FCRD- T10-201 0-00005 FCRD Technical Integration Office (TIO) DOCUMENT NUMBER REQUEST TRANSMITTAL SHEET 1. Document Information Document Title/Description: Generic Disposal System Modeling--Fiscal Year 2011 Revision: 0 Progress Re~ort Assigned Document Number: FCRD-USED-2011-000184 Effective Start Date: 08/1112011 Document Author/Creator: D. Clayton, G. Freeze, T. Hadgu, E. Hardin, J. Lee, OR .~: J. Prouty, R. Rogers, W.M. Nutt, J. Berkholzer, H.H. Liu, L. Zheng, S. Chu Document Owner: Palmer Vaughn Date Range: Originating Organization: Sandia National Laboratories From: To: Milestone OM1 ~M2 OM3 ~M4 o Not a Milestone Milestone Number:: M21UF034101 and M41UF035102 Work Package WBS Number: FTSN11 UF0341 and FTSN11 UF0351; 1.02.08.03 Controlled Unclassified Infonnation (CUI) Type ~ None OOUO OAT o Other FCRD SYSTEM: Year: o FUEL Fuels 2011 OINTL International

303

Final Report: Retrofit Aeration System (RAS) for Francis Turbine  

DOE Green Energy (OSTI)

Osage Plant and Bagnell Dam impounds the Osage River forming the Lake of the Ozarks in Missouri. Since it is nearly 100 feet deep, the lake stratifies during the summer months causing low DO water to be discharged into the Osage river below the dam. To supplement DO, the turbines are vented during the low DO season. AmerenUE is continually researching new methods of DO enhancement. New turbines, manufactured by American Hydro Corporation, were installed in Units 3 & 5 during the spring of 2002. Additional vent capacity and new nosecones were included in the new turbine design. The retrofit aeration system is an attempt to further enhance the DO in the tailrace by installation of additional venting capability on Unit 6 (not upgraded with new turbine) and refining design on special nosecones which will be mounted on both Unit 3 (upgraded turbine) and Unit 6. Baseline DO testing for Units 3 & 6 was conducted mid August, 2002. This data wascompared to further tests planned for the summer of 2003 and 2004 after installation of the retrofit aeration system.

Alan Sullivan; DOE Project Officer Keith Bennett

2006-08-01T23:59:59.000Z

304

FY 2006 Annual Progress Report for Heavy Vehicle Systems Optimization Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Heavy veHicle SyStemS Heavy veHicle SyStemS OptimizatiOn prOgram U.S. Department of Energy FreedomCAR and Vehicle Technologies Program 1000 Independence Avenue, S.W. Washington, DC 20585-0121 FY 2006 Annual Progress Report for Heavy Vehicle Systems Optimization Program Submitted to: U.S. Department of Energy Energy Efficiency and Renewable Energy FreedomCAR and Vehicle Technologies Program Advanced Vehicle Technology Analysis and Evaluation Lee Slezak, Technology Manager Heavy Vehicle Systems Optimization Program FY 2006 Annual Report iii CONTENTS I. Aerodynamic Drag Reduction......................................................................................................... 1 A. DOE Project on Heavy Vehicle Aerodynamic Drag .................................................................. 1

305

New Report Shows Trend Toward Larger Offshore Wind Systems, with 11  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Report Shows Trend Toward Larger Offshore Wind Systems, with 11 Report Shows Trend Toward Larger Offshore Wind Systems, with 11 Advanced Stage Projects Proposed in U.S. Waters New Report Shows Trend Toward Larger Offshore Wind Systems, with 11 Advanced Stage Projects Proposed in U.S. Waters October 23, 2013 - 10:52am Addthis The Energy Department today released a new report showing progress for the U.S. offshore wind energy market in 2012, including the completion of two commercial lease auctions for federal Wind Energy Areas and 11 commercial-scale U.S. projects representing over 3,800 megawatts (MW) of capacity reaching an advanced stage of development. Further, the report highlights global trends toward building offshore turbines in deeper waters and using larger, more efficient turbines in offshore wind farms, increasing the amount of electricity delivered to consumers.

306

Enforcement Guidance Supplement 03-02, Revision to Occurrence Report-Based Noncompliance Tracking System Reporting Criteria  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

03-02 03-02 Department of Energy Washington, DC 20585 September 5, 2003 MEMORANDUM FOR: DOE PAAA COORDINATORS CONTRACTOR PAAA COORDINATORS FROM: STEPHEN M. SOHINKI DIRECTOR OFFICE OF PRICE-ANDERSON ENFORCEMENT SUBJECT: Enforcement Guidance Supplement 03-02: Revision to Occurrence Report-Based Noncompliance Tracking System Reporting Criteria Section 1.3 of the Operational Procedures for Enforcement, published in June 1998, provides the opportunity for the Office of Price-Anderson Enforcement (OE) to periodically issue clarifying guidance regarding the processes used in its enforcement activities. OE typically issues such guidance in the form of Enforcement Guidance Supplements (EGS), which provide information or recommendations only and impose

307

Market-analysis system for conservation technologies. Draft final report  

SciTech Connect

A prototype market analysis methodology to provide DOE decision makers guidance in evaluating and selecting strategies that promote energy conservation technologies is discussed. The methodology, named MASCOT (Market Analysis System for COnservation Technologies), was designed for the residential water heating market. However, the basic logic can be extended to other market segments, such as space heating and conditioning, and the commercial sector. MASCOT forecasts the market performance of any arbitrary set of technologies that the user chooses. The methodology captures the time-varying effects of technological and economic changes in the market, determines the critical features for new water heating technologies, calculates the likely energy impacts from the use of the actual technologies, and provides information concerning the sensitivity of the results to assumptions about market conditions, technology characteristics, and the factors underlying market penetration. (PSB)

Morris, P.A.; Thapa, M.N.; Bauman, D.S.; Froker, D.B.

1981-12-14T23:59:59.000Z

308

CDIF-MHD generator system conceptual design. Final report  

DOE Green Energy (OSTI)

The objective of this Program is to conduct a conceptual design of an MHD Generator System (MHD) to be coupled to candidate development coal-fired MHD combustion chambers at the MHD Component Development and Integration Facility (CDIF) for the purpose of developing design techniques utilized for the design of large MHD generators. The MHD is to be designed for continuous operation. A hexagonal cross section, diagonal conducting wall configuration operating in the supersonic mixed impulse-reaction mode with an inlet Mach number of 1.59 and with a uniform magnetic field of four Tesla throughout were selected. The design operating conditions and performance are presented, and a design analysis is included. (WHK)

Not Available

1977-03-01T23:59:59.000Z

309

Solar liquid-desiccant air-conditioning system. Final report  

DOE Green Energy (OSTI)

A design for a closed, diurnal, intermittent absorption chiller for passive solar air-conditioning using liquid sorbents has been constructed and tested. LiBr-H/sub 2/O will not work with this design because of its low vapor pressure at the temperature available. The approach has possibilities using the 2 LiBr-ZrBr-CH/sub 3/OH or H/sub 2/O-NH/sub 3/ sorbent refrigerant pairs. The use of H/sub 2/O-NH/sub 3/ appears to be the better candidate because of the lower solution viscosity and less cycle weight, through tank volumes and collector requirements are similar. Further study of other refrigerant pairs such as S-Thiocyanate-ammonia is indicated, however, the difficulties encountered in construction and low potential coefficient of performance, and thus large collection area needed, makes commercialization of such a system doubtful in the foreseeable future.

Not Available

310

Energy Department Expands Gas Gouging Reporting System to Include 1-800  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Expands Gas Gouging Reporting System to Include Expands Gas Gouging Reporting System to Include 1-800 Number: 1-800-244-3301 Energy Department Expands Gas Gouging Reporting System to Include 1-800 Number: 1-800-244-3301 September 6, 2005 - 9:50am Addthis Washington, DC - Energy Secretary Samuel W. Bodman announced today that the Department of Energy has expanded its gas gouging reporting system to include a toll-free telephone hotline. The hotline is available to American consumers starting today. "While we've largely seen the best of American generosity and unity throughout the recovery effort, we recognize that there are some bad actors that may try to take advantage of the situation. Consumers are our first line of defense in guarding against gas price gouging. I can assure you, our Administration - from the President down - takes this issue very

311

High-end-Computer System Performance: Science and Engineering - Final Report  

SciTech Connect

This report summarizes the research conducted as part of the UMD effort of the multi-site PERC project. This project developed and enhanced the Dyninst instrumentation system and the Active Harmony auto-tuning framework.

Hollingsworth, Jeffrey K.

2012-01-27T23:59:59.000Z

312

Wind Turbine Generator System Power Performance Test Report for the Entegrity EW50 Wind Turbine  

DOE Green Energy (OSTI)

Report on the results of the power performance test that the National Renewable Energy Laboratory (NREL) conducted on Entegrity Wind System Inc.'s EW50 small wind turbine.

Smith, J.; Huskey, A.; Jager, D.; Hur, J.

2011-05-01T23:59:59.000Z

313

Advanced turbine systems program--conceptual design and product development. Quarterly report, November 1994--January 1995  

SciTech Connect

Research continued in the design and development of advanced gas turbine systems. This report presents progress towards turbine blade development, diffuser development, combustion noise investigations,catalytic combustion development, and diagnostic probe development.

1995-02-01T23:59:59.000Z

314

Advanced turbine systems program conceptual design and product development. Quarterly report, February 1995--April 1995  

Science Conference Proceedings (OSTI)

Research continued on the design of advanced turbine systems. This report describes the design and test of critical components such as blades, materials, cooling, combustion, and optical diagnostics probes.

NONE

1995-06-01T23:59:59.000Z

315

Advanced thermal barrier coating system development. Technical progress report, September 1, 1997--November 30, 1997  

SciTech Connect

The objectives of this project were to provide an improved thermal barrier coating system with increased temperature capability and reliability. This report describes bond coat development, manufacturing, nondestructive evaluation, maintenance, and repair, and bench testing.

1997-12-12T23:59:59.000Z

316

Building Thermal Envelope Systems and Materials (BTESM) progress report for DOE Office of Buildings Energy Research  

SciTech Connect

The Monthly Report of the Building Thermal Envelope Systems and Materials (BTESM) Program is a monthly update of both in-house ORNL projects and subcontract activities in the research areas of building materials, wall systems, foundations, roofs, building diagnostics, and research utilization and technology transfer. Presentations are not stand-alone paragraphs every month. Their principal values are the short-time lapse between accomplishment and reporting and their evolution over a period of several months.

Burn, G. (comp.)

1990-01-01T23:59:59.000Z

317

Building Thermal Envelope Systems and Materials (BTESM) progress report for DOE Office of Buildings Energy Research  

SciTech Connect

The Monthly Report of the Building Thermal Envelope Systems and Materials (BTESM) Program is a monthly update of both in-house ORNL projects and subcontract activities in the research areas of building materials, wall systems, foundations, roofs, and building diagnostics. Presentations are not stand-alone paragraphs every month. Their principal values are the short-time lapse between accomplishment and reporting and their evolution over a period of several months.

Burn, G. (comp.)

1990-12-01T23:59:59.000Z

318

Building thermal envelope systems and materials (BTESM) monthly progress report for DOE Office Buildings Energy Research  

SciTech Connect

The Monthly Report of the Building Thermal Envelope Systems and Materials (BTESM) Program is a monthly update of both in-house ORNL projects and subcontract activities in the research areas of building materials, wall systems, foundations, roofs, and building diagnostics. Presentations are not stand-alone paragraphs every month. Their principal values are the short-time lapse between accomplishment and reporting and their evolution over a period of several months.

Burn, G. (comp.)

1990-11-01T23:59:59.000Z

319

Fermilab Central Computing Facility: Energy conservation report and mechanical systems design optimization and cost analysis study  

SciTech Connect

This report is developed as part of the Fermilab Central Computing Facility Project Title II Design Documentation Update under the provisions of DOE Document 6430.1, Chapter XIII-21, Section 14, paragraph a. As such, it concentrates primarily on HVAC mechanical systems design optimization and cost analysis and should be considered as a supplement to the Title I Design Report date March 1986 wherein energy related issues are discussed pertaining to building envelope and orientation as well as electrical systems design.

Krstulovich, S.F.

1986-11-12T23:59:59.000Z

320

Advanced Turbine Systems Program: Conceptual design and product development. Quarterly status report, May--July 1994  

Science Conference Proceedings (OSTI)

The goal of the overall Advanced Turbine Systems (ATS) program is to develop and commercialize ultrahigh-efficiency gas-turbine-based power systems for utility and industrial applications. This contract will complete conceptual design and begin component testing for a utility-scale power system having 60% efficiency. Progress reports are presented for the following tasks: selection of natural gas-fired advance turbine systems (GFATS); selection of coal-fired advanced turbine systems (CFATS); market study; system definition and analysis; and design and test of critical components.

Not Available

1994-09-14T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

The feasibility assessment of a U.S. natural gas production reporting system uniform production reporting model. Final report, July 1993--June 1994  

SciTech Connect

The Uniform Production Reporting Model (UPRM) project was charged with identifying the best practices and procedures of the natural gas producing states related to the gathering, management, and dissemination of production data. It is recommended that the producing states begin the process of upgrading state systems using the concepts embodied in the UPRM model.

NONE

1994-06-01T23:59:59.000Z

322

Case studies of thermal energy storage (TES) systems: Evaluation and verification of system performance. Final report  

Science Conference Proceedings (OSTI)

We have developed two case studies to review and analyze energy performance of thermal energy storage CMS systems in commercial buildings. Our case studies considered two partial ice storage systems in Northern California. For each case, we compiled historical data on TES design, installation, and operation. This information was further enhanced by data obtained through interviews with the building owners and operators. The performance and historical data of the TES systems and their components were grouped into issues related to design, installation, operation, and maintenance of the systems. Our analysis indicated that (1) almost all problems related to the operation of TES and non-TES systems could be traced back to the design of the system, and (2) the identified problems were not unique to the TES systems. There were as many original problems with ``conventional`` HVAC systems and components as with TES systems. Judging from the problems related to non-TES components identified in these two case studies, it is reasonable to conclude that conventional systems have as many problems as TES systems, but a failure, in a TES system may have a more dramatic impact on thermal comfort and electricity charges. The objective of the designers of the TES systems in the case-study buildings was to design just-the-right-size systems so that both the initial investment and operating costs would be minimized. Given such criteria, a system is typically designed only for normal and steady-state operating conditions-which often precludes due consideration to factors such as maintenance, growth in the needed capacity, ease of the operation, and modularity of the systems. Therefore, it is not surprising to find that these systems, at least initially, did not perform to the design intent and expectation and that they had to go through extended periods of trouble-shooting.

Akbari, H.; Sezgen, O.

1992-01-01T23:59:59.000Z

323

Central receiver solar thermal system. Phase 1, CDRL item 10. Second quarterly technical progress report  

DOE Green Energy (OSTI)

Results of analysis and design efforts are summarized. This is the second quarterly technical progress report published on the Phase 1 Central Receiver Solar Thermal Power System contract. The dominant activities during the reporting period have involved the detailed definition of the subsystem research experiments and the design of the test articles and test facilities. Summaries of these activities are presented. Design changes to the 10-MWe pilot plant preliminary design baseline which have occurred during the report period are also described.

Hallet, Jr., R. W.; Gervais, R. L.

1976-04-01T23:59:59.000Z

324

Decontamination systems information and research program. Quarterly report, July--September 1995  

Science Conference Proceedings (OSTI)

The projects reported for the WVU Cooperative Agreement are categorized into the following three areas: (1) in situ remediation process development; (2) advanced product applications testing; and (3) information systems, public policy, community outreach, and economics. Summaries of the significant accomplishments for the projects reported during the period 1 July 1995 through 30 September 1995 are presented.

NONE

1995-10-01T23:59:59.000Z

325

High efficiency vapor-fed AMTEC system for direct conversion. Appendices for final report  

DOE Green Energy (OSTI)

This report consists of four appendices for the final report. They are: Appendix A: 700 C Vapor-Fed AMTEC Cell Calculations; Appendix B: 700 C Vapor-Fed AMTEC Cell Parts Drawings; Appendix C: 800 C Vapor-Fed AMTEC Cell Calculations; and Appendix D: 800 C Wick-Pumped AMTEC Cell System Design.

Anderson, W.G.; Bland, J.J.

1997-05-23T23:59:59.000Z

326

Ris Energy Report 8 The intelligent energy system infrastructure for the future  

E-Print Network (OSTI)

Risø Energy Report 8 The intelligent energy system infrastructure for the future Risø-R-1695(EN) September 2009 Edited by Hans Larsen and Leif Sønderberg Petersen #12;Risø Energy Report 8 Edited by Hans Larsen and Leif Sønderberg Petersen, Risø National Laboratory for Sustainable Energy Technical University

327

Ris Energy Report 8 The intelligent energy system infrastructure for the future  

E-Print Network (OSTI)

Risø Energy Report 8 The intelligent energy system infrastructure for the future Reprint Petersen #12;Risø Energy Report 5 Renewable energy for power and transport Global energy policy today is dominated by three concerns: security of supply, climate change, and energy for development and poverty

328

Decontamination systems information and research program. Quarterly report, January--March 1995  

Science Conference Proceedings (OSTI)

The projects reported during this period are categorized into the following three areas: 1.0 Site Remediation Technologies, 2.0 Advanced Product Applications Testing, and 3.0 Information Systems, Public Policy, Community Outreach, and Economics. Summaries of the significant accomplishments for the projects reported during this period, are presented.

NONE

1995-04-01T23:59:59.000Z

329

Rooftop PV system. Final technical progress report, Phase II  

SciTech Connect

Under this four-year PV:BONUS Program, ECD and United Solar are developing and demonstrating two new lightweight flexible building integrated Photovoltaic (BIPV) modules specifically designed as exact replacements for conventional asphalt shingles and standing seam metal roofing. These modules can be economically and aesthetically integrated into new residential and commercial buildings, and address the even larger roofing replacement market. The modules are designed to be installed by roofing contractors without special training which minimizes the installation and balance of system costs. The modules will be fabricated from high-efficiency, multiple-junction a-Si alloy solar cells developed by ECD and United Solar. Under the Phase I Program, which ended in March 1994, we developed two different concept designs for rooftop PV modules: (1) the United Solar overlapping (asphalt shingle replacement) shingle-type modules and (2) the ECD metal roof-type modules. We also developed a plan for fabricating, testing and demonstrating these modules. Candidate demonstration sites for our rooftop PV modules were identified and preliminary engineering designs for these demonstrations were developed; a marketing study plan was also developed. The major objectives of the Phase II Program, which started in June 1994 was (1) to develop, test, and qualify these new rooftop modules; (2) to develop mechanical and electrical engineering specifications for the demonstration projects; and (3) to develop a marketing/commercialization plan.

1995-08-01T23:59:59.000Z

330

Cooperative field test program for wind systems. Final report  

DOE Green Energy (OSTI)

The objectives of the Federal Wind Energy Program, managed by the US Department of Energy (DOE), are (1) to assist industry and utilities in achieving a multi-regional US market penetration of wind systems, and (2) to establish the United States as the world leader in the development of advanced wind turbine technology. In 1984, the program conducted a series of planning workshops with representatives from the wind energy industry to obtain input on the Five-Year Research Plan then being prepared by DOE. One specific suggestion that came out of these meetings was that the federal program should conduct cooperative research tests with industry to enhance the technology transfer process. It was also felt that the active involvement of industry in DOE-funded research would improve the state of the art of wind turbine technology. DOE established the Cooperative Field Test Program (CFTP) in response to that suggestion. This program was one of the first in DOE to feature joint industry-government research test teams working toward common objectives.

Bollmeier, W.S. II; Dodge, D.M.

1992-03-01T23:59:59.000Z

331

Wind energy/geothermic/solar heating system. Final report  

SciTech Connect

I've observed three distinct ''camps'' of renewable energy resources; WIND, Geothermic, and Solar. None of the three are completely adequate for the NE by themselves. I observe little effort to combine them to date. My objective has been to demonstrate that the three can be combined in a practical system. To mitagate the high cost and poor payback for individual residences, I believe neighborhoods of 4 to 5 homes, apartment complexes or condominiums could form an Energy Association alloting a piece of ground (could be a greenbelt) which would contain the well or wells, solar boosted underground water storage and the Solar banks. These are the high cost items which could be prorated and ammortized by the Association. Easements would permit each residence underground insulated water lines for individual heat pump conversions to existing forced air furnaces. Where regulations permit, an individual home could erect his own windmill to belt drive his freon compressor. With or without the optional windmill the water to freon heat pump with its solar boosts on the well water, will enjoy COP's (coefficient of Performances or times better than electric resistance heat) beyond anything on the market today. In a neighborhood energy association, all trenching could be done together all plumbing could be one contract and they could qualify for quantity discounts on heat pump units, chillers and components and installation.

Not Available

1981-01-01T23:59:59.000Z

332

Aerial Measuring System Technical Integration Annual Report 2002  

SciTech Connect

Fiscal Year 2002 is the second year of a five-year commitment by the U.S. Department of Energy, National Nuclear Security Administration (NNSA) to invest in development of new and state-of-the-art technologies for the Aerial Measuring Systems (AMS) project. In 2000, NNSA committed to two million dollars for AMS Technical Integration (TI) for each of five years. The tragedy of September 11, 2001, profoundly influenced the program. NNSA redirected people and funding resources at the Remote Sensing Laboratory (RSL) to more immediate needs. Funds intended for AMS TI were redirected to NNSA's new posture of leaning further forward throughout. AMS TI was brought to a complete halt on December 10, 2001. Then on April 30, 2002, NNSA Headquarters allowed the restart of AMS TI at the reduced level of $840,000. The year's events resulted in a slow beginning of several projects, some of which were resumed only a few weeks before the AMS TI Symposium held at RSL on July 30.

Bechtel Nevada Remote Sensing Laboratory

2003-06-01T23:59:59.000Z

333

Molten salt thermal energy storage systems. Project 8981, final report  

DOE Green Energy (OSTI)

The feasibility of storing thermal energy at temperatures of 450/sup 0/ to 535/sup 0/C (850/sup 0/ to 1000/sup 0/F) in the form of latent heat of fusion has been examined for over 30 inorganic salts and salt mixtures. Alkali carbonate mixtures are attractive as phase-change storage materials in this temperature range because of their relatively high storage capacity and thermal conductivity, moderate cost, low volumetric expansion upon melting, low corrosivity, and good chemical stability. An equimolar mixture of Li/sub 2/CO/sub 3/ and K/sub 2/CO/sub 3/, which melts at 505/sup 0/C with a latent heat of 148 Btu/lb, was chosen for experimental study. The cyclic charge/discharge behavior of laboratory- and engineering-scale systems was determined and compared with predictions based on a mathematical heat-transfer model that was developed during this program. The thermal performance of one engineering-scale unit remained very stable during 1400 hours of cyclic operation. Several means of improving heat conduction through the solid salt were explored. Areas requiring further investigation have been identified.

Maru, H.C.; Dullea, J.F.; Kardas, A.; Paul, L.

1978-03-01T23:59:59.000Z

334

Lower Flathead System Fisheries Study, 1986 Interim Report.  

DOE Green Energy (OSTI)

We believe our results have clearly shown Kerr hydroelectric operations and operational constraints have negatively affected Flathead River trout and northern pike populations and the aquatic habitat which support them. Even so, it is possible to mitigate many of these impacts and develop a very important fishery. Trout abundance in the lower Flathead averaged only 19 fish per kilometer, the lowest abundance of trout for a river of this size in Montana. Little main channel spawning by trout was observed and most spawning probably occurs in tributaries. Lower river tributaries support resident populations of brook, rainbow, brown, and cutthroat trout; and a small resident population of bull trout is present in the South Fork of the Jocko River. Using weirs, spawning runs of rainbow and brown trout from the main river were monitored entering the Jocko River and the Post/Mission Creek system. Utilization of Crow Creek by main river trout stocks of trout was limited to the 6 km segment below Crow Dam. Evaluations of tributary spawning gravels showed high levels of silt which would suggest poor survival of trout eggs. Excessive harvest in the tributaries was indicated by analysis of age class structure and abundance of trout greater than 200 mm.

Bradshaw, William H.; DosSantos, Joseph M.; Darling, James M.

1986-08-01T23:59:59.000Z

335

SP-100 planetary mission/system preliminary design study. Final report, technical information report  

SciTech Connect

This report contains a discussion on many aspects of a nuclear electric propulsion planetary science mission and spacecraft using the proposed SP-100 nuclear power subsystem. A review of the science rationale for such missions is included. A summary of eleven nuclear electric propulsion planetary missions is presented. A conceptual science payload, mission design, and spacecraft design is included for the Saturn Ring Rendezvous mission. Spacecraft and mission costs have been estimated for two potential sequences of nuclear electric propulsion planetary missions. The integration issues and requirements on the proposed SP-100 power subsystems are identified.

Jones, R.M. [ed.

1986-02-01T23:59:59.000Z

336

Ris Energy Report 4 System control and communication 4 9 System control and communication  

E-Print Network (OSTI)

a useful degree of robustness to the system. Energy systems are increasingly market-based Energy systems at least three markets: long-term bilat- eral energy contracts, a day-ahead market (12­36 hours running of the markets. · Adding large amounts of renewable energy (RE) to the mix is a challenge

337

National Geoscience Data Repository System: Phase 2 final report  

SciTech Connect

The American Geological Institute (AGI) has completed Phase 2 of a project to establish a National Geoscience Data Repository System (NGDRS). The project`s primary objectives are to preserve geoscience data in jeopardy of being destroyed and to make that data available to those who have a need to use it in future investigations. These data are available for donation to the public as a result of the downsizing that has occurred in the major petroleum and mining companies in the US for the past decade. In recent years, these companies have consolidated domestic operations, sold many of their domestic properties and relinquished many of their leases. The scientific data associated with those properties are no longer considered to be useful assets and are consequently in danger of being lost forever. The national repository project will make many of these data available to the geoscience community for the first time. Phase 2 encompasses the establishment of standards for indexing and cataloging of geoscience data and determination of the costs of transferring data from the private sector to public-sector data repositories. Pilot projects evaluated the feasibility of the project for transfer of different data types and creation of a Web-based metadata supercatalog and browser. Also as part of the project, a national directory of geoscience data repositories was compiled to assess what data are currently available in existing facilities. The next step, Phase 3, will focus on the initiation of transfer of geoscience data from the private sector to the public domain and development of the web-based Geotrek metadata supercatalog.

NONE

1997-07-01T23:59:59.000Z

338

Remote Underwater Characterization System - Innovative Technology Summary Report  

Science Conference Proceedings (OSTI)

Characterization and inspection of water-cooled and moderated nuclear reactors and fuel storage pools requires equipment capable of operating underwater. Similarly, the deactivation and decommissioning of older nuclear facilities often requires the facility owner to accurately characterize underwater structures and equipment which may have been sitting idle for years. The underwater characterization equipment is often required to operate at depths exceeding 20 ft (6.1 m) and in relatively confined or congested spaces. The typical baseline approach has been the use of radiation detectors and underwater cameras mounted on long poles, or stationary cameras with pan and tilt features mounted on the sides of the underwater facility. There is a perceived need for an inexpensive, more mobile method of performing close-up inspection and radiation measurements in confined spaces underwater. The Remote Underwater Characterization System (RUCS) is a small, remotely operated submersible vehicle intended to serve multiple purposes in underwater nuclear operations. It is based on the commercially-available Scallop vehicle1, but has been modified by Department of Energys Robotics Technology Development Program to add auto-depth control, and vehicle orientation and depth monitoring at the operator control panel. The RUCS is designed to provide visual and gamma radiation characterization, even in confined or limited access areas. It was demonstrated in August 1998 at Idaho National Engineering and environmental Laboratory (INEEL) as part of the INEEL Large Scale Demonstration and Deployment Project. During the demonstration it was compared in a head-tohead fashion with the baseline characterization technology. This paper summarizes the results of the demonstration and lessons learned; comparing and contrasting both technologies in the areas of cost, visual characterization, radiological characterization, and overall operations.

Willis, Walter David

1999-04-01T23:59:59.000Z

339

Waste systems. Progress report, January 1982-February 1983  

SciTech Connect

A laboratory-scale beryllium electrorefining cell has been placed in operation and metallic beryllium with a purity greater than 99.95% has been produced. Methods of uranium chip disposal have been evaluated by performing bench- and pilot-scale testing and by surveying present chip disposal methods. A design criteria has been completed for a new production uranium chip disposal facility. Two types of cementation immobilization processes are being developed to treat several Rocky Flats wastes which do not currently meet repository acceptance criteria. The nitrate salts, as now shipped, are an extremely fine powder, composed chiefly of sodium and potassium nitrate. Nitrates are an oxidizer, and their behavior in a possible fire would be of concern. Accident caused fires involving a cargo of boxed nitrate salts were modeled and the burning characteristics noted. In addition, gypsum cement was tested as an immobilization matrix to reduce dispersibility. A program is in process to construct a facility to remotely size reduce gloveboxes and miscellaneous equipment contaminated with plutonium and other radioactive nuclides. The Title II engineering package is completed and the construction of the facility has been initiated. Modification and additions to the 82 kg/h Fluidized Bed Incinerator were made in preparation for turning the unit over to Production. A program was initiated to identify, characterize, and evaluate for recycle all the spent oil and solvent streams which are immobilized and disposed as Transuranic (TRU) waste. Three technologies were evaluted for denitrification method was studied at Rocky Flats while a thermal decomposition process and a molten salt chemical conversion technique were investigated on a subcontract basis with Thagard Research Corporation and Rockwell International, Energy Systems Group, respectively.

Hickle, G.L.

1983-10-24T23:59:59.000Z

340

Conceptual design and systems analysis of photovoltaic power systems. Final report. Volume III(2). Technology  

DOE Green Energy (OSTI)

Conceptual designs were made and analyses were performed on three types of solar photovoltaic power systems. Included were Residential (1 to 10 kW), Intermediate (0.1 to 10 MW), and Central (50 to 1000 MW) Power Systems to be installed in the 1985 to 2000 time period. The following analyses and simulations are covered: residential power system computer simulations, intermediate power systems computer simulation, central power systems computer simulation, array comparative performance, utility economic and margin analyses, and financial analysis methodology.

Pittman, P.F.

1977-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

CATALYSTS NHI Thermochemical Systems FY 2009 Year-End Report  

DOE Green Energy (OSTI)

Fiscal Year 2009 work in the Catalysts project focused on advanced catalysts for the decomposition of sulfuric acid, a reaction common to both the Sulfur-Iodine (S-I) cycle and the Hybrid Sulfur cycle. Prior years effort in this project has found that although platinum supported on titanium oxide will be an acceptable catalyst for sulfuric acid decomposition in the integrated laboratory scale (ILS) project, the material has short comings, including significant cost and high deactivation rates due to sintering and platinum evaporation. For pilot and larger scale systems, the catalyst stability needs to be improved significantly. In Fiscal Year 2008 it was found that at atmospheric pressure, deactivation rates of a 1 wt% platinum catalyst could be reduced by 300% by adding either 0.3 wt% iridium (Ir) or 0.3 wt% ruthenium (Ru) to the catalyst. In Fiscal Year 2009, work focused on examining the platinum group metal catalysts activity and stability at elevated pressures. In addition, simple and complex metal oxides are known to catalyze the sulfuric acid decomposition reaction. These metal oxides could offer activities comparable to platinum but at significantly reduced cost. Thus a second focus for Fiscal Year 2009 was to explore metal oxide catalysts for the sulfuric acid decomposition reaction. In Fiscal Year 2007 several commercial activated carbons had been identified for the HI decomposition reaction; a reaction specific to the S-I cycle. Those materials should be acceptable for the pilot scale project. The activated carbon catalysts have some disadvantages including low activity at the lower range of reactor operating temperature (350 to 400C) and a propensity to generate carbon monoxide in the presence of water that could contaminate the hydrogen product, but due to limited funding, this area had low priority in Fiscal Year 2009. Fiscal Year 2009 catalyst work included five tasks: development, and testing of stabilized platinum based H2SO4 catalysts, development and testing of metal oxide based H2SO4 catalysts, support of the ILS for catalyst studies, conducting a long term catalyst stability test at anticipated operating temperatures and pressures, and developing capabilities for conducting pressurized catalyst tests.

Daniel M. Ginosar

2009-09-01T23:59:59.000Z

342

Development of a comprehensive reporting system for a school reform organization: The Accelerated Schools Project  

E-Print Network (OSTI)

Given the conflicting research results on the effectiveness of whole-school reform models (Nunnery, 1998; Stringfield & Herman, 1997; American Institutes for Research, 1999; U.S. Department of Education, 2004), there is a need to focus on the evaluation procedures of whole-school reform organizations. Because the ultimate goal is to improve school performance, it should also be a goal of each whole-school reform organization to design a comprehensive data collection system to evaluate each school?s performance. A comprehensive reporting system was developed for a school reform organization, the Accelerated Schools Project (ASP). Using the steps of the research and development process recommended by Borg and Gall (1989), this study: (a) developed a theoretical framework for the reporting system, (b) identified data that should be collected in the reporting system, (c) performed a field test with an expert panel of educational professionals, (d) developed a preliminary form of the reporting system, (e) performed a main field test with principals and coaches in the ASP network, (f) reported field test results, (g) revised the preliminary reporting system, (h) developed a website for the reporting system, and (i) provided recommendations for the completion, dissemination and implementation of the system in accelerated schools across the nation. This study has important implications for both the ASP community and for the entire whole-school reform community. For the ASP community, the reporting system could be used: (a) to collect data in all accelerated schools across the nation (b) as a longitudinal database of information to monitor data on each ASP school, and (c) to generate school summary reports on ASP schools. These data will assist researchers in measuring the effectiveness of the ASP model on student achievement and other important variables. For the whole-school reform community, the method used in this study could be replicated in other school reform organizations to develop a comprehensive reporting system. By providing consistent data for school reform organizations to evaluate the impact of their models on students and schools, educational researchers will be better equipped to understand each model?s impact, and thus will better understand the diverse research results on school reform effectiveness.

Stephens, Jennifer Anne

2004-12-01T23:59:59.000Z

343

Conventional Facilities Chapter 6: HVAC Systems 6-1 NSLS-II Preliminary Design Report  

E-Print Network (OSTI)

Conventional Facilities Chapter 6: HVAC Systems 6-1 NSLS-II Preliminary Design Report 6 MECHANICAL ­ HVAC SYSTEMS 6.1 Design Criteria 6.1.1 Codes and Standards The latest edition of the codes, standards have adequate capacity and head, no chilled water pumps #12;Conventional Facilities Chapter 6: HVAC

Ohta, Shigemi

344

Status report - advanced heat exchanger technology for a CCGT power generation system  

Science Conference Proceedings (OSTI)

This report gives laboratory and field test results of a specially designed heat exchanger for coal-fired power plants. The system incorporates an atmospheric fluidized bed and combustion system for pulverized coal. The heat exchanger was made from both metallic and ceramic materials.

Wright, D.E.; Tignac, L.L.

1982-01-01T23:59:59.000Z

345

Prototype solar heating and cooling systems including potable hot water. Quarterly reports, November 1976--June 1977  

DOE Green Energy (OSTI)

This report covers the progress made in the development, delivery and support of two prototype solar heating and cooling systems including potable hot water. The system consists of the following subsystems: collector, auxiliary heating, potable hot water, storage, control, transport, and government-furnished site data acquisition.

Not Available

1978-12-01T23:59:59.000Z

346

SOLERAS - Solar Controlled Environment Agriculture Project. Final report, Volume 5. Science Applications, Incorporated system requirements definition  

DOE Green Energy (OSTI)

This report sets forth the system requirements for a Solar Controlled-Environment Agriculture System (SCEAS) Project. In the report a conceptual baseline system description for an engineering test facility is given. This baseline system employs a fluid roof/roof filter in combination with a large storage tank and a ground water heat exchanger in order to provide cooling and heating as needed. Desalination is accomplished by pretreatment followed by reverse osmosis. Energy is provided by means of photovoltaics and wind machines in conjunction with storage batteries. Site and climatic data needed in the design process are given. System performance specifications and integrated system design criteria are set forth. Detailed subsystem design criteria are presented and appropriate references documented.

Not Available

1985-01-01T23:59:59.000Z

347

Advanced coal-fueled gas turbine systems. Quarterly report, January--March 1993  

SciTech Connect

All scheduled tests for the slagging combustor program were completed prior to this reporting period. The draft topical report for the slagging combustor testing was begun in January and the draft submitted to DOE/METC for review in March. Work was completed on the (Advanced Turbine Systems) Phase 1 program and the draft topical begun in January. The ATS Phase 1 draft topical report was submitted to DOE/METC in March. Comments to the report were received back from METC prior to the end of March allowing for the preparation of the final version of the report to begin. Conceptual design of a combustion turbine system that can be integrated in a pressurized fluidized bed combustor (PFBC) application was completed at the end of March. An intermediate design review was held in February with METC and a draft of the topical report was begun during the reporting period. Details of the individual subtask work for the first generation PFBC combustion turbine system conceptual design are discussed in the ``Generic Turbine Design Study Final Report`` which was issued June 1993 to DOE/METC.

1993-07-01T23:59:59.000Z

348

Satellite power system concept development and evaluation program system definition technical assessment report  

DOE Green Energy (OSTI)

The results of the system definition studies conducted by NASA as a part of the Department of Energy/National Aeronautics and Space Administration SPS Concept Development and Evaluation Program are summarized. The purpose of the system definition efforts was to identify and define candidate SPS concepts and to evaluate the concepts in terms of technical and cost factors. Although the system definition efforts consisted primarily of evaluation and assessment of alternative technical approaches, a reference system was also defined to facilitate economic, environmental, and societal assessments by the Department of Energy. This reference system was designed to deliver 5 GW of electrical power to the utility grid. Topics covered include system definition; energy conversion and power management; power transmission and reception; structures, controls, and materials; construction and operations; and space transportation.

Not Available

1980-12-01T23:59:59.000Z

349

Systems Studies Department FY 78 activity report. Volume 2. Systems analysis. [Sandia Laboratories, Livermore  

DOE Green Energy (OSTI)

The Systems Studies Department at Sandia Laboratories Livermore (SLL) has two primary responsibilities: to provide computational and mathematical services and to perform systems analysis studies. This document (Volume 2) describes the FY Systems Analysis highlights. The description is an unclassified overview of activities and is not complete or exhaustive. The objective of the systems analysis activities is to evaluate the relative value of alternative concepts and systems. SLL systems analysis activities reflect Sandia Laboratory programs and in 1978 consisted of study efforts in three areas: national security: evaluations of strategic, theater, and navy nuclear weapons issues; energy technology: particularly in support of Sandia's solar thermal programs; and nuclear fuel cycle physical security: a special project conducted for the Nuclear Regulatory Commission. Highlights of these activities are described in the following sections. 7 figures. (RWR)

Gold, T.S.

1979-02-01T23:59:59.000Z

350

Energy Sources and Systems Analysis: 40 South Lincoln Redevelopment District (Short Report)  

Science Conference Proceedings (OSTI)

This report presents the a brief overview of the results of a case study to analyze district energy systems for their potential use in a project that involves redeveloping 270 units of existing public housing, along with other nearby sites. When complete, the redevelopment project will encompass more than 900 mixed-income residential units, commercial and retail properties, and open space. The analysis estimated the hourly heating, cooling, domestic hot water, and electric loads required by the community; investigated potential district system technologies to meet those needs; and researched available fuel sources to power such systems. A full report of this case study is also available.

Not Available

2011-08-01T23:59:59.000Z

351

Technical analysis of US Army Weapons Systems and related advanced technologies of military interest. Final report  

Science Conference Proceedings (OSTI)

This report summarizes the activities and accomplishments of an US Army technology security project designed to identify and develop effective policy guidelines for militarily critical technologies in specific Army systems and in broad generic technology areas of military interest, Individual systems analyses are documented in separate Weapons Systems Technical Assessments (WSTAs) and the general generic technology areas are evaluated in the Advanced Technology Assessment Reports (ATARs), However, specific details of these assessments are not addressed here, only recommendations regarding aspects of the defined approach, methodology, and format are provided and discussed.

NONE

1991-06-14T23:59:59.000Z

352

10 MWe solar thermal central receiver pilot plant control system automation test report  

DOE Green Energy (OSTI)

This report describes results of tests on the automatic features added to the control system for the 10 MWe Solar Thermal Central Receiver Pilot Plant located near Barstow, CA. The plant, called Solar One, is a cooperative activity between the Department of Energy and the Associates: Southern California Edison, the Los Angeles Dept. of Water and Power and the California Energy Commission. This report provides an overview of the automation features added to the plant control system, a description of tests performed on the system, and the results of those tests.

Not Available

1987-04-01T23:59:59.000Z

353

Determining Long-Term Performance of Cool Storage Systems from Short-Term Tests, Final Report  

E-Print Network (OSTI)

This is the final report for ASHRAE Research Project 1004-RP: Determining Long-Term Performance of Cool Storage Systems from Short-Term Tests. This report presents the results of the development and application of the methodology to Case Study #2, the Delmar College, in Corpus Christi, Texas, and Case Study #3, the Austin Convention Center, in Austin, Texas. A previous report presented the analysis results for Case Study #1, which was a large hotel located in San Francisco, CA. This report also includes a summary and discussion of the results from all three case studies, recommendations for further research, and a step-by-step guide to applying the analysis methodology.

Reddy, T. A.; Elleson, J.; Haberl, J. S.

2000-01-01T23:59:59.000Z

354

Solar energy system performance evaluation. Seasonal report for SEMCO, Loxahatchee, Florida  

DOE Green Energy (OSTI)

The analysis used is based on instrumented system data monitored and collected for at least one full season of operation. The objective of the analysis is to report the long-term field performance of the installed system and to make technical contributions to the definition of techniques and requirements for solar energy system design. The solar energy system was designed to supply domestic hot water for a family of four, single-family residence. The SEMCO System 80 consists of two liquid flat plate collectors, single tank, pump, controls, and transport lines.

Not Available

1980-01-01T23:59:59.000Z

355

Solar energy system performance evaluation. Seasonal report for SEMCO, Macon, Georgia  

DOE Green Energy (OSTI)

The analysis used is based on instrumented system data monitored and collected for at least one full season of operation. The objective of the analysis is to report the long-term field performance of the installed system and to make technical contributions to the definition of techniques and requirements for solar energy system design. The solar energy system was designed to supply domestic hot water for a family of four, single-family residence. The SEMCO System 80 consists of liquid (silicone) flat plate collectors, single tank, pump, controls and transport lines.

Not Available

1980-01-01T23:59:59.000Z

356

Ingham County Geriatric Medical Care Facility solar water-heating system refurbishments. Final technical report  

DOE Green Energy (OSTI)

The tasks of the refurbishment of a damaged solar water heating system are outlined. The system is a closed loop, 50% glycol antifreeze system consisting of 14 rows of 6 series manifolds each containing 6 solar collectors connected in parallel for a total of 504 modules. The Wyle Laboratories' test report for the Revere Model 132 flat plate collector is appended. A collector test plan and photographs are also appended. Reference CAPE-2834. (LS)

Not Available

1983-07-01T23:59:59.000Z

357

Report of Survey of the Los Alamos Tritium Systems Test Assembly Facility |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

the Los Alamos Tritium Systems Test Assembly the Los Alamos Tritium Systems Test Assembly Facility Report of Survey of the Los Alamos Tritium Systems Test Assembly Facility The purpose of this document is to report the results of a survey conducted at the Los Alamos Tritium Systems Test Assembly (TSTA Facility). The survey was conducted during the week of 3/20/00. The primary purpose of the survey is to identify facility conditions and issues that need to be addressed to transfer responsibility for the facility from the Office of Science (SC) to the Office of Environmental Management (EM). The second purpose is to provide EM with insight regarding the facility's risks and liabilities, which may influence the management of eventual downstream life-cycle activities. The survey and this report are part of a process for implementing the

358

Developing Secure Power Systems Professional Competence: Alignment and Gaps in Workforce Development Programs-Summary Report  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

41 41 Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830 Developing Secure Power Systems Professional Competence: Alignment and Gaps in Workforce Development Programs-Summary Report LR O'Neil TJ Vanderhorst, Jr MJ Assante J Januszewski, III DH Tobey R Leo TJ Conway K Perman July 2013 PNNL- 22641 Developing Secure Power Systems Professional Competence: Alignment and Gaps in Workforce Development Programs-Summary Report LR O'Neil TJ Vanderhorst, Jr MJ Assante J Januszewski, III DH Tobey R Leo TJ Conway K Perman Contributors: SGC Panel Members July, 2013 Prepared by: Pacific Northwest National Laboratory and NBISE Secure Power Systems Professional Project Team This document is a summarization of the report, Developing Secure Power Systems

359

TITLE III EVALUATION REPORT FOR THE MATERIAL AND PERSONNEL HANDLING SYSTEM  

Science Conference Proceedings (OSTI)

This Title III Evaluation Report (TER) provides the results of an evaluation that was conducted on the Material and Personnel Handling System. This TER has been written in accordance with the ''Technical Document Preparation Plan for the Mined Geologic Disposal System Title III Evaluation Reports'' (BA0000000-01717-4600-00005 REV 03). The objective of this evaluation is to provide recommendations to ensure consistency between the technical baseline requirements, baseline design, and the as-constructed Material and Personnel Handling System. Recommendations for resolving discrepancies between the as-constructed system, the technical baseline requirements, and the baseline design are included in this report. Cost and Schedule estimates are provided for all recommended modifications.

T. A. Misiak

1998-05-21T23:59:59.000Z

360

Commercialization of PV-powered pumping systems for use in utility PV service programs. Final report  

DOE Green Energy (OSTI)

The project described in this report was a commercialization effort focused on cost-effective remote water pumping systems for use in utility-based photovoltaic (PV) service programs. The project combined a commercialization strategy tailored specifically for electric utilities with the development of a PV-powered pumping system that operates conventional ac pumps rather than relying on the more expensive and less reliable PV pumps on the market. By combining these two attributes, a project goal was established of creating sustained utility purchases of 250 PV-powered water pumping systems per year. The results of each of these tasks are presented in two parts contained in this Final Summary Report. The first part summarizes the results of the Photovoltaic Services Network (PSN) as a new business venture, while the second part summarizes the results of the Golden Photon system installations. Specifically, results and photographs from each of the system installations are presented in this latter part.

NONE

1997-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Decontamination systems information and research program. Quarterly report, October 1995--December 1995  

Science Conference Proceedings (OSTI)

West Virginia University (WVU) and the U.S. Department of Energy Morgantown Energy Technology Center (DOE/METC) entered into a Cooperative Agreement on August 29, 1992 titled {open_quotes}Decontamination Systems Information and Research programs{close_quotes} (DOE Instrument No. DE-FC21-92MC29467) This report contains the efforts of the research projects comprising the Agreement for the 4th calendar quarter of 1995, and is the final quarterly report deliverable required for the period ending 31 December 1995. The projects reported for the WVU Cooperative Agreement are categorized into the following three areas: 1.0 In Situ Remediation Process Development, 2.0 Advanced Product Applications Testing, and 3.0 Information Systems, Public Policy, Community Outreach, and Economics. Summaries of the significant accomplishments for the projects reported during the period 1 October 95 through 31 December 95 are presented in the following discussions.

NONE

1995-12-01T23:59:59.000Z

362

Security assessment of power systems including energy storage. Progress report, July 1, 1978--September 30, 1978  

DOE Green Energy (OSTI)

Progress in assessing the security of power systems is reviewed. Further evaluation has been performed on the previously developed simplified model of the current-fed force-commutated converter (CFFCC). Validation studies were performed using the CFFCC as a control interface between a one-machine, three-bus power system equivalent and a superconducting magnetic energy storage device. The highlights of this investigation are reported. The identification of power system electromechanical models from systems measurements, with only normal load variation as a disturbing input, is being studied. A maximum liklihood estimation procedure has been partly developed. The procedure uses auto correlation information as an input rather than the observed time series.

Carroll, D.P.; Triezenberg, D.M.

1978-10-01T23:59:59.000Z

363

Economic assessment of the utilization of lead-acid batteries in electric utility systems. Final report  

DOE Green Energy (OSTI)

Specific applications in which lead--acid batteries might be economically competitive on an electric utility system are identified. Particular attention is given to searching the Public Service Electric and Gas Company (PSE and G) system for installations of batteries which could defer or cancel costly transmission and/or distribution projects. Although the transmission and distribution data are based on specific applications on the PSE and G system, the generation data are based on a national reference system. The report analyzes and summarizes all costs and savings attributable to lead--acid batteries. 40 figures, 78 tables. (RWR)

Johnson, A.C.; Hynds, J.A.; Nevius, D.R.; Nunan, G.A.; Sweetman, N.

1977-04-01T23:59:59.000Z

364

Ocean thermal energy conversion power system development-I. Volume 4. Appendix G. Preliminary design report  

DOE Green Energy (OSTI)

The conceptual design of a 40 to 50 MW closed cycle ammonia OTEC commercial plant, the preliminary design of a 10 MW OTEC module analogous to the 50 MW module, and the preliminary design of heat exchanger test articles (evaporator and condenser) representative of the 50 MW heat exchangers for testing in OTEC-1 are presented. This volume of the report presents Appendix G: ammonia cycle, auxiliaries and ancillaries. Design descriptions are given (for the 50 MW commercial plant and the 10 MW module) for the ammonia vapor and condensate systems, ammonia storage and fill systems, noncondensible gas removal systems, ammonia cleanup systems, ammonia unloading systems, leak detection systems, and fluid sampling systems. (WHK)

Not Available

1978-12-18T23:59:59.000Z

365

Working Group Report on - Space Nuclear Power Systems and Nuclear Waste  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Working Group Report on - Space Nuclear Power Systems and Nuclear Working Group Report on - Space Nuclear Power Systems and Nuclear Waste Technology R&D Working Group Report on - Space Nuclear Power Systems and Nuclear Waste Technology R&D "Even though one cannot anticipate the answers in basic research, the return on the public's investment can be maximized through long-range planning of the most promising avenues to explore and the resources needed to explore them." (p. v) "Pursuit of this goal entails developing new technologies and advanced facilities, educating young scientists, training a technical workforce, and contributing to the broader science and technology enterprise?." (p. vi) Ref:: "Nuclear Science: A Long Range Plan", DOE/NSF, Feb. 1996. The purpose of this effort is to develop the first iteration of a

366

Working Group Report on - Space Nuclear Power Systems and Nuclear Waste  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Working Group Report on - Space Nuclear Power Systems and Nuclear Working Group Report on - Space Nuclear Power Systems and Nuclear Waste Technology R&D Working Group Report on - Space Nuclear Power Systems and Nuclear Waste Technology R&D "Even though one cannot anticipate the answers in basic research, the return on the public's investment can be maximized through long-range planning of the most promising avenues to explore and the resources needed to explore them." (p. v) "Pursuit of this goal entails developing new technologies and advanced facilities, educating young scientists, training a technical workforce, and contributing to the broader science and technology enterprise?." (p. vi) Ref:: "Nuclear Science: A Long Range Plan", DOE/NSF, Feb. 1996. The purpose of this effort is to develop the first iteration of a

367

Advanced turbine systems program conceptual design and product development: Quarterly report, November 1993--January 1994  

SciTech Connect

This report describes progress made in the advanced turbine systems program conceptual design and product development. The topics of the report include selection of the Allison GFATS, castcool technology development for industrial engines test plan and schedule, code development and background gathering phase for the ultra low NOx combustion technology task, active turbine clearance task, and water vapor/air mixture cooling of turbine vanes task.

1995-01-01T23:59:59.000Z

368

Developing, testing, evaluating and optimizing solar heating systems. Project status report for October and November 1996  

DOE Green Energy (OSTI)

This report describes progress on 3 projects: Integrated tank/heat exchanger modeling and experiments for solar thermal storage; Advanced residential solar domestic hot water systems; and Incident angle modifiers (IAMs) by the Monte Carlo method for cylindrical solar collectors. IAMs are used to correct for effects such as shading, back plane reflectance, inter-reflection, etc. Summaries are given for the first two projects; however, a full draft report is given for the third.

NONE

1997-01-01T23:59:59.000Z

369

Addressing System Integration Issues Required for the Developmente of Distributed Wind-Hydrogen Energy Systems: Final Report  

DOE Green Energy (OSTI)

Wind generated electricity is a variable resource. Hydrogen can be generated as an energy storage media, but is costly. Advancements in power electronics and system integration are needed to make a viable system. Therefore, the long-term goal of the efforts at the University of North Dakota is to merge wind energy, hydrogen production, and fuel cells to bring emission-free and reliable power to commercial viability. The primary goals include 1) expand system models as a tool to investigate integration and control issues, 2) examine long-term effects of wind-electrolysis performance from a systematic perspective, and 3) collaborate with NREL and industrial partners to design, integrate, and quantify system improvements by implementing a single power electronics package to interface wild AC to PEM stack DC requirements. This report summarizes the accomplishments made during this project.

Mann, M.D; Salehfar, H.; Harrison, K.W.; Dale, N.; Biaku, C.; Peters, A.J.; Hernandez-Pacheco: E.

2008-04-01T23:59:59.000Z

370

Central receiver solar thermal power system. Phase 1. CDRL item 2; Pilot Plant preliminary design report. Volume II. System decription and system analysis  

SciTech Connect

An active system analysis and integration effort has been maintained. These activities have included the transformation of initial program requirements into a preliminary system design, the evolution of subsystem requirements which lay the foundation for subsystem design and test activity, and the overseeing of the final preliminary design effort to ensure that the subsystems are operationally compatible and capable of producing electricity at the lowest possible cost per unit of energy. Volume II of the Preliminary Design Report presents the results of the overall system effort that went on during this contract. The effort is assumed to include not only the total system definition and design but also all subsystem interactions.

Hallet, Jr., R. W.; Gervais, R. L.

1977-10-01T23:59:59.000Z

371

Occurrence reporting and processing system (ORPS) lessons learned: Tools to improve workplace performance  

Science Conference Proceedings (OSTI)

Various Department of Energy (DOE) orders require DOE and DOE contractor personnel to review abnormal events to gain lessons learned information. The term ``event`` is used to mean a real-time occurrence. When reviewing events data, it must be possible to determine what happened and why (including root causes), the impacts, the appropriate corrective actions, and any lessons learned that might be applicable to activities of other operations or contractors. Merely obtaining the information will not prevent occurrence of a similar event; contributing conditions must be corrected. It is important for managers, trainers, and others to learn from the events of others so that they may apply these experiences to their own activities. Reports of events must be analyzed to determine possible applicability to other facilities and/or job functions. Relevant information can then be used to correct defects and improve facilities and operations, thus making them more efficient and safer for all employees. Lessons learned information is particularly helpful in planning employee training and in developing training curriculum and programs. Lessons learned information can be obtained from many sources. It can be found in the Safety Performance Measurement System`s Computerized Accident/Incident Reporting System (CAIRS) module, the S&H Publications module, the Unusual Occurrence Reports module, and the Office of Nuclear Safety ``Operating Experience Weekly Summary.`` One important source of lessons teamed information is the Occurrence Reporting and Processing System (ORPS) database, which contains event data from September 1, 1990, to the present. This report discusses this source.

Commander, S.L.

1992-12-31T23:59:59.000Z

372

Conceptual Design of a Strategic Power Infrastructure Defense (SPID) System: EPRI/DoD Complex Interactive Networks/Systems Initiativ e; First Annual Report  

Science Conference Proceedings (OSTI)

This report describes research sponsored by EPRI and the Department of Defense for the Initiative on Complex Interactive Networks / Systems. Through this initiative, the Advanced Power Technologies (APT) Consortium has developed a conceptual design of the Strategic Power Infrastructure Defense (SPID) system. This first annual report from the APT Consortium describes hidden failures and how they contribute to catastrophic failures of bulk power systems.

2000-05-24T23:59:59.000Z

373

Development, Demonstration, and Field Testing of Enterprise-Wide Distributed Generation Energy Management System: Final Report  

DOE Green Energy (OSTI)

This report details progress on subcontract NAD-1-30605-1 between the National Renewable Energy Laboratory and RealEnergy (RE), the purpose of which is to describe RE's approach to the challenges it faces in the implementation of a nationwide fleet of clean cogeneration systems to serve contemporary energy markets. The Phase 2 report covers: utility tariff risk and its impact on market development; the effect on incentives on distributed energy markets; the regulatory effectiveness of interconnection in California; a survey of practical field interconnection issues; trend analysis for on-site generation; performance of dispatch systems; and information design hierarchy for combined heat and power.

Greenberg, S.; Cooley, C.

2005-01-01T23:59:59.000Z

374

Small power systems study technical summary report. Volume II. Inventory of small generating units in U. S. utility systems  

SciTech Connect

Data identifying small (less than or equal to 10 MW) power units in the United States are tabulated. The data are listed alphabetically by state and are reported sequentially for investor owned utilities, municipal utilities, and electrical cooperatives and other utility systems. For a given utility system, the generating units are divided into steam turbines, diesel generators and gas turbines. The number and size of generating units are listed. A summary tabulation of the number of generating units of each type and total generating capacity by state is presented.

Sitney, L.R.

1978-05-31T23:59:59.000Z

375

Operable Unit 3-13, Group 7, SFE-20 Hot Waste Tank System Remedial Action Report  

SciTech Connect

This Remedial Action Report summarizes activities undertaken to remediate the Operable Unit 3-13, Group 7, SFE-20 Hot Waste Tank System at the Idaho Nuclear Technology and Engineering Center at the Idaho National Laboratory Site. The site addressed in this report was defined in the Operable Unit 3-13 Record of Decision and subsequent implementing documents. This report concludes that remediation requirements and cleanup goals established for the site have been accomplished and is hereafter considered a No Further Action site.

Lee Davison

2009-06-30T23:59:59.000Z

376

Hydrogen-control systems for severe LWR accident conditions - a state-of-technology report  

Science Conference Proceedings (OSTI)

This report reviews the current state of technology regarding hydrogen safety issues in light water reactor plants. Topics considered in this report relate to control systems and include combustion prevention, controlled combustion, minimization of combustion effects, combination of control concepts, and post-accident disposal. A companion report addresses hydrogen generation, distribution, and combustion. The objectives of the study were to identify the key safety issues related to hydrogen produced under severe accident conditions, to describe the state of technology for each issue, and to point out ongoing programs aimed at resolving the open issues.

Hilliard, R.K.; Postma, A.K.; Jeppson, D.W.

1983-03-01T23:59:59.000Z

377

Model documentation report: Industrial sector demand module of the national energy modeling system  

SciTech Connect

This report documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Model. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code. This document serves three purposes. First, it is a reference document providing a detailed description of the NEMS Industrial Model for model analysts, users, and the public. Second, this report meets the legal requirements of the Energy Information Administration (EIA) to provide adequate documentation in support of its model. Third, it facilitates continuity in model development by providing documentation from which energy analysts can undertake model enhancements, data updates, and parameter refinements as future projects.

NONE

1998-01-01T23:59:59.000Z

378

Model documentation report: Commercial Sector Demand Module of the National Energy Modeling System  

SciTech Connect

This report documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Commercial Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated through the synthesis and scenario development based on these components. This report serves three purposes. First, it is a reference document providing a detailed description for model analysts, users, and the public. Second, this report meets the legal requirement of the Energy Information Administration (EIA) to provide adequate documentation in support of its statistical and forecast reports (Public Law 93-275, section 57(b)(1)). Third, it facilitates continuity in model development by providing documentation from which energy analysts can undertake model enhancements, data updates, and parameter refinements as future projects.

NONE

1995-02-01T23:59:59.000Z

379

8 -Circuits, Systems and Communications Microelectromechanical Systems 8 RLE Progress Report 144  

E-Print Network (OSTI)

MEMS Analysis System and Implementation Sponsors Computer Microvision for Microelectromechanical. This is where computer microvision acts as a good analysis stool to analyze the X, Y, and Z motions of a MEMS device during the development and testing stages of the design process. Computer microvision

380

Residential solar photovoltaic systems: Final report for the Northeast Residential Experiment Station  

Science Conference Proceedings (OSTI)

This report covers research and development work conducted by the MIT Energy Lab. from July 1982 through June 1986. This Energy Lab. work in the field of solar photovoltaic systems followed six years of similar work at the MIT Lincoln Lab. under the same contract with the US DOE. The final report from the Lincoln Lab. period was published by Lincoln Lab. in 1983. During the period of Energy Lab. involvement, the project focused on the refinement of residential scale, roof-mounted photovoltaic systems for application in the northeastern US. Concurrent with the conclusion of MIT`s involvement, the New England Electric Co. is building a major field test of residential photovoltaics in Gardner, Massachusetts to determine experimentally the effects of photovoltaics on electric power company operations. Using systems designs and technology developed at MIT, the long-term performance of these thirty residential systems in Gardner will provide a measure of our success.

Kern, E.C. Jr.

1986-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Renewable wood fuel: Fuel feed system for a pulverized coal boiler. Final report  

DOE Green Energy (OSTI)

This report evaluates a pilot test program conducted by New York State Gas & Electric Corporation to evaluate the feasibility of co-firing a pulverized coal plant with renewable wood fuels. The goal was to establish that such a co-firing system can reduce air emissions while maintaining good operational procedures and cost controls. The test fuel feed system employed at Greenidge Station`s Boiler 6 was shown to be effective in feeding wood products. Emission results were promising and an economic analysis indicates that it will be beneficial to pursue further refinements to the equipment and systems. The report recommends further evaluation of the generation and emission impacts using woods of varied moisture contents and at varied Btu input rates to determine if a drying system would be a cost-effective option.

NONE

1996-01-01T23:59:59.000Z

382

Energy Management of Steam Distribution Systems Through Energy Audits and Computerized Reporting Programs  

E-Print Network (OSTI)

"This presentation will highlight the economic losses associated with steam distribution systems and how to establish good energy management programs to reduce energy cost by 15 to 25 percent. Recognizing energy losses in steam systems involves: 1. Steam lost through defective valves, fittings and traps. 2. Loss through damaged or inefficient insulation. 3. Energy loss through misapplication of steam traps and improper piping practices. Energy management programs will cover steam energy auditing and computerized reporting systems that are proven methods of conserving energy and substantially reducing costs. Typical savings of a facility with 1,000 traps could exceed $300,000.00 annually. The use of computerized reporting systems can be a valuable tool in establishing good energy management practices and preventive maintenance programs. The reasons why, and the methods of how a computer aided preventive maintenance program can be established will be presented "

Rivers, N.; Mandzuk, N.

1988-09-01T23:59:59.000Z

383

Title III Evaluation Report for the Subsurface Fire Water System and Subsurrface Portion of the Non-Portable Water System  

SciTech Connect

The objective of this evaluation is to provide recommendations to ensure consistency between the technical baseline requirements, baseline design, and the as-constructed SFWS/SNPWS. Recommendations for resolving discrepancies between the as-constructed systems, the technical baseline requirements, and the baseline design are included in this report. Cost and schedule estimates are provided for all recommended modifications. This report does not address items which do not meet current safety or code requirements. These items are identified to the CMO and immediate action is taken to correct the situation. The report does identify safety and code items for which the A/E is recommending improvements. The recommended improvements will exceed the minimum requirements of applicable code and safety guidelines. These recommendations are intended to improve and enhance the operation and maintenance of the facility.

R.E. Flye

1998-09-29T23:59:59.000Z

384

Effective Personnel Exposure Control in Shortened Refueling Outages: Interim Report: Review of Remote Monitoring Systems  

Science Conference Proceedings (OSTI)

Many utilities are currently investigating technologies such as remote monitoring systems (RMS) to optimize their radiation protection capabilities. This interim report provides a brief description of the hardware and features of remote monitoring systems at four nuclear power plants, and serves as the basis for EPRI work dedicated to the advancement of RMS technology for radiation protection applications. This information can significantly benefit those utilities presently planning major RMS installations.

2002-11-18T23:59:59.000Z

385

Status report: The US Department of Energy`s Advanced Turbine Systems Program  

SciTech Connect

ATS is poised to capture the majority of new electric power generation capacity well into the next century. US DOE led the programs supporting the development of ATS technology enabling gas turbine manufacturers to provide ATS systems to the commercial marketplace. A progress report on the ATS program is presented in this paper. The technical challenges, advanced critical technology requirements, and system configurations meeting the goals of the program are discussed.

Zeh, C.M.

1996-12-31T23:59:59.000Z

386

Feasibility demonstration of the Sperry down-well pumping system. Final report  

DOE Green Energy (OSTI)

Advantages of down-well pumping (vs. free-flowing) of geothermal hot-water wells are presented, and criteria for such a system are discussed. The main body of the report is presented under the following section headings: the Sperry down-well pumping system; field test program; field operations; test results; and, conclusions and recommendations. The appendix includes a summary of boiler heat transfer and pressure drop calculations. (JGB)

Not Available

1977-05-01T23:59:59.000Z

387

Hanford ETR Bulk Vitrification System - Demonstration Bulk Vitrification System (DBVS) Review Report  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

A Comprehensive Technical A Comprehensive Technical Review of the Demonstration Bulk Vitrification System Technical Assessment Conducted by an Independent and External Team of Experts Volume 1 September 28, 2006 Chartered by CH2M HILL Hanford Group, Inc. Richland, Washington 99352 RPP-31314 Executive Summary In May 2006, CH2M HILL Hanford Group, Inc. chartered an Expert Review Panel (ERP) to review the current status of the Demonstration Bulk Vitrification System (DBVS). It is the consensus of the ERP that bulk vitrification is a technology that requires further development and evaluation to determine its potential for meeting the Hanford waste stabilization mission. No fatal flaws (issues that would jeopardize the overall DBVS mission that cannot be mitigated) were found, given the current state of the project.

388

The Wide-area Energy Management System Phase 2 Final Report  

DOE Green Energy (OSTI)

The higher penetration of intermittent generation resources (including wind and solar generation) in the Bonneville Power Administration (BPA) and California Independent System Operator (CAISO) balancing authorities (BAs) raises issue of requiring expensive additional fast grid balancing services in response to additional intermittency and fast up and down power ramps in the electric supply system. The overall goal of the wide-area energy management system (WAEMS) project is to develop the principles, algorithms, market integration rules, a functional design, and a technical specification for an energy storage system to help cope with unexpected rapid changes in renewable generation power output. The resulting system will store excess energy, control dispatchable load and distributed generation, and utilize inter-area exchange of the excess energy between the California ISO and Bonneville Power Administration control areas. A further goal is to provide a cost-benefit analysis and develop a business model for an investment-based practical deployment of such a system. There are two tasks in Phase 2 of the WAEMS project: the flywheel field tests and the battery evaluation. Two final reports, the Wide-area Energy Management System Phase 2 Flywheel Field Tests Final Report and the Wide-area Energy Storage and Management System Battery Storage Evaluation, were written to summarize the results of the two tasks.

Lu, Ning; Makarov, Yuri V.; Weimar, Mark R.

2010-08-31T23:59:59.000Z

389

Advanced turbine systems study system scoping and feasibility study. Final report  

SciTech Connect

United Technologies Research Center, Pratt & Whitney Commercial Engine Business, And Pratt & Whitney Government Engine and Space Propulsion has performed a preliminary analysis of an Advanced Turbine System (ATS) under Contract DE-AC21-92MC29247 with the Morgantown Energy Technology Center. The natural gas-fired reference system identified by the UTC team is the Humid Air Turbine (HAT) Cycle in which the gas turbine exhaust heat and heat rejected from the intercooler is used in a saturator to humidify the high pressure compressor discharge air. This results in a significant increase in flow through the turbine at no increase in compressor power. Using technology based on the PW FT4000, the industrial engine derivative of the PW4000, currently under development by PW, the system would have an output of approximately 209 MW and an efficiency of 55.3%. Through use of advanced cooling and materials technologies similar to those currently in the newest generation military aircraft engines, a growth version of this engine could attain approximately 295 MW output at an efficiency of 61.5%. There is the potential for even higher performance in the future as technology from aerospace R&D programs is adapted to aero-derivative industrial engines.

1993-04-01T23:59:59.000Z

390

Raytheon downhole information system. Electromagnetic borehole measurements while drilling system. Final report  

DOE Green Energy (OSTI)

A description is given of the Raytheon Downhole Information System (RDIS), a real time electromagnetic borehole measurements while drilling system, applicable to oil, gas, and geothermal drilling. It communicates in both directions through the earth in a single hop at a downlink data rate of 3 bps and uplink rates dependent on depth--typically 6 bits/second at 10,000 ft and 2 bits/second at 15,000 ft; electromagnetic signal transmission time of approximately .1 second. Downhole hardware for communications, sensors, and power are packaged in three 30 ft subs. Downhole hardware can be developed to permit operation in a 275/sup 0/C geothermal environment. A cost analysis is included that predicts RDIS service could be economically priced at approximately $1000/day. Commercial availability depends primarily on proof of capability by demonstration in a working drilling well. The most significant portions of needed hardware are available. A description of a geothermal drilling telemetry system is included in Appendix A.

Kolker, M.; Greene, A.H.; Kasevich, R.S.; Robertson, J.C.; Grossi, M.D.

1978-03-01T23:59:59.000Z

391

Occurrence reporting and processing system (ORPS) lessons learned: Tools to improve workplace performance  

SciTech Connect

Various Department of Energy (DOE) orders require DOE and DOE contractor personnel to review abnormal events to gain lessons learned information. The term event'' is used to mean a real-time occurrence. When reviewing events data, it must be possible to determine what happened and why (including root causes), the impacts, the appropriate corrective actions, and any lessons learned that might be applicable to activities of other operations or contractors. Merely obtaining the information will not prevent occurrence of a similar event; contributing conditions must be corrected. It is important for managers, trainers, and others to learn from the events of others so that they may apply these experiences to their own activities. Reports of events must be analyzed to determine possible applicability to other facilities and/or job functions. Relevant information can then be used to correct defects and improve facilities and operations, thus making them more efficient and safer for all employees. Lessons learned information is particularly helpful in planning employee training and in developing training curriculum and programs. Lessons learned information can be obtained from many sources. It can be found in the Safety Performance Measurement System's Computerized Accident/Incident Reporting System (CAIRS) module, the S H Publications module, the Unusual Occurrence Reports module, and the Office of Nuclear Safety Operating Experience Weekly Summary.'' One important source of lessons teamed information is the Occurrence Reporting and Processing System (ORPS) database, which contains event data from September 1, 1990, to the present. This report discusses this source.

Commander, S.L.

1992-01-01T23:59:59.000Z

392

Safety Evaluation Report on Siemens Power Corporation TELEPERM XS Safety System  

Science Conference Proceedings (OSTI)

This document is the Safety Evaluation Report (SER) issued by the U.S. Nuclear Regulatory Commission (NRC) to Siemens Power Corporation on the TELEPERM XS digital reactor protection system described in EPRI TR-114017. This SER is available only in combination with TR-114017.

2000-08-03T23:59:59.000Z

393

Software Verification and Validation Test Report for the HEPA filter Differential Pressure Fan Interlock System  

Science Conference Proceedings (OSTI)

The HEPA Filter Differential Pressure Fan Interlock System PLC ladder logic software was tested using a Software Verification and Validation (V&V) Test Plan as required by the ''Computer Software Quality Assurance Requirements''. The purpose of his document is to report on the results of the software qualification.

ERMI, A.M.

2000-09-05T23:59:59.000Z

394

CITI Technical Report 0114 A Practical Distributed Authorization System for GARA  

E-Print Network (OSTI)

CITI Technical Report 01­14 A Practical Distributed Authorization System for GARA Wiliam A. Adamson Technology Integration (CITI), University of Michigan Office of the Vice President for Research, Merit, University Corporation for Advanced Internet Development(UCAID), European Orga­ nization for Nuclear Research

Michigan, University of

395

PROJECT W-551 INTERIM PRETREATMENT SYSTEM TECHNOLOGY SELECTION SUMMARY DECISION REPORT AND RECOMMENDATION  

SciTech Connect

This report provides the conclusions of the tank farm interim pretreatment technology decision process. It documents the methodology, data, and results of the selection of cross-flow filtration and ion exchange technologies for implementation in project W-551, Interim Pretreatment System. This selection resulted from the evaluation of specific scope criteria using quantitative and qualitative analyses, group workshops, and technical expert personnel.

CONRAD EA

2008-08-12T23:59:59.000Z

396

Columbia River Coordinated Information System (CIS), 1992-1993 Annual Report.  

DOE Green Energy (OSTI)

The purposes of this report are to: (1) describe the project to date; (2) to document the work and accomplishments of the (CIS) project for Fiscal Year 1993; and (3) to provide a glimpse of future project direction. The concept of a Coordinated Information System (CIS) as an approach to meeting the growing needs for regionally standardized anadromous fish information.

Rowe, Mike; Roger, Phillip B.; O'Connor, Dick

1993-11-01T23:59:59.000Z

397

Advanced turbine systems program conceptual design and product development. Annual report, August 1994--July 1995  

SciTech Connect

Objective of the ATS program is to develop ultra-high efficiency, environmentally superior, and cost-competitive gas turbine systems for base-load application in utility, independent power producer, and industrial markets. This report discusses the major accomplishments achieved during the second year of the ATS Phase 2 program, particularly the design and test of critical components.

1994-10-01T23:59:59.000Z

398

Advanced turbine systems program conceptual design and product development. Quarterly report, August 1993--November 1994  

Science Conference Proceedings (OSTI)

This report discusses a series of heat balance programs were developed and reviewed in a Westinghouse Engineering Department meeting. The cycle formats were reviewed and candidate conditions and components selected for additional investigations,for the selection of the Natural Gas-fired Advanced Turbines Systems (GFATS).

Not Available

1993-12-01T23:59:59.000Z

399

Advanced turbine systems program conceptual design and product development. Quarterly report, November 1993--January 1994  

Science Conference Proceedings (OSTI)

This report discusses a series of materials testing programs were developed and reviewed in a Westinghouse Engineering Department meeting. The cycle formats were reviewed and candidate conditions and components selected for additional investigations,for the selection of the Natural Gas-fired Advanced Turbines Systems (GFATS).

Not Available

1994-04-01T23:59:59.000Z

400

9 -Circuits, Systems and Communications Computer Microvision for MEMS 9 RLE Progress Report 144  

E-Print Network (OSTI)

9 - Circuits, Systems and Communications ­ Computer Microvision for MEMS ­ 9 RLE Progress Report 144 9-1 Computer Microvision for MEMS Academic and Research Staff Professor Dennis M. Freeman (Freeman) 1. Computer Microvision for MEMS Academic and Research Staff Professor Dennis M. Freeman, Michael

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

10 -Circuits, Systems and Communications -Computer Microvision for MEMS -10 RLE Progress Report 145  

E-Print Network (OSTI)

10 - Circuits, Systems and Communications - Computer Microvision for MEMS - 10 RLE Progress Report 145 10-1 Computer Microvision for MEMS Academic and Research Staff Professor Dennis M. Freeman Ryu Support Staff Janice Balzer 1. Computer Microvision for MEMS Sponsors Defense Advanced Research

402

Simulated coal gas MCFC power plant systems verification. Technical progress report  

DOE Green Energy (OSTI)

The following tasks are included in this project: Commercialization; Power plant development; Manufacturing facilities development; Test facility development; Stack research; and Advanced research and technology development. This report briefly describes the subtasks still to be completed: Power plant system test with reformed natural gas; Upgrading of existing, US government-owned, test facilities; and Advanced MCFC component research.

NONE

1998-04-01T23:59:59.000Z

403

Wind Turbine Generator System Safety and Function Test Report for the Entegrity EW50 Wind Turbine  

DOE Green Energy (OSTI)

This report summarizes the results of a safety and function test that NREL conducted on the Entegrity EW50 wind turbine. This test was conducted in accordance with the International Electrotechnical Commissions' (IEC) standard, Wind Turbine Generator System Part 2: Design requirements for small wind turbines, IEC 61400-2 Ed.2.0, 2006-03.

Smith, J.; Huskey, A.; Jager, D.; Hur, J.

2012-11-01T23:59:59.000Z

404

Wind Turbine Generator System Safety and Function Test Report for the Ventera VT10 Wind Turbine  

DOE Green Energy (OSTI)

This report summarizes the results of a safety and function test that NREL conducted on the Ventera VT10 wind turbine. This test was conducted in accordance with the International Electrotechnical Commissions' (IEC) standard, Wind Turbine Generator System Part 2: Design requirements for small wind turbines, IEC 61400-2 Ed.2.0, 2006-03.

Smith, J.; Huskey, A.; Jager, D.; Hur, J.

2012-11-01T23:59:59.000Z

405

The livestock mandatory price reporting system: Lamb industry perceptions and impact  

E-Print Network (OSTI)

The livestock mandatory price reporting system was approved by Congress in July of 1999, signed into law on October 22, 1999, and launched on April 2, 2001. In announcing the implementation of the mandatory price reporting system, the USDA claimed that it would provide information on 80% to 95% of the volume of all cattle, boxed beef, slaughter hogs, sheep and lamb meat, and imported lamb meat transactions. The new law had three explicit objectives: (1) facilitate price discovery, (2) make livestock markets more open, and (3) provide all market participants with market information that can be easily understood (USDA 2001a). This study attempts to determine if the new mandatory price reporting system had achieved these objectives in the perspective of the sheep and lamb industry during the period of the study. Survey questionnaires were developed to determine the perceptions of lamb producers and feeders regarding the effect of the mandatory price reporting system on: (1) the price discovery process, (2) the openness and transparency of lamb buying and selling transactions in the market, and (3) the quantity, accuracy, availability, and timeliness of information needed to make production and marketing decisions. First, the cross-tabulation or descriptive categorical analysis provided the basis for an aggregate evaluation of the perceptions of the survey respondents. Second, a logit regression analysis based on the ordinal regression models was built to consider the relationship between the perceptions of the responding sheep and lamb producers and feeders regarding the new mandatory price reporting system and key characteristics of those respondents (such as age, gender, years of experience, size of operations, etc.). During the period of the study, most respondents believed that the new Mandatory Price Reporting Act has not facilitated or enhanced their power to negotiate prices. Although producers from bigger ranches and feeders from larger capacity ranches reported some improvement in the price discovery process, most respondents believed that packers and feeders were still manipulating the sheep and lambs markets. Neither producers nor feeders perceived any improvements in the availability and openness of private transactions. The mandatory livestock price reports about the sheep and lamb market prices are considered the least useful information source for majority of respondents, as well as the most difficult to understand. The most useful and understandable source is perceived to be the voluntary USDA market reports and other ranchers and feeders.

Poghosyan, Artak Vahagn

2002-01-01T23:59:59.000Z

406

Advanced Turbine System (ATS): Task 1, System scoping and feasibility study. Final report  

SciTech Connect

Present GT(Gas Turbine) Systems are available to achieve 52% (LHV) thermal efficiencies, plants in construction will be capable of 54%, and the goal of this study is to identify incentives, technical issues, and resource requirements to develop natural gas-and coal-compatible ATS which would have a goal of 60% or greater based on LHV. The prime objective of this project task is to select a natural gas-fired ATS (Advanced Turbine System) that could be manufactured and marketed should development costs not be at issue with the goals of: (1) Coal of electricity 10% below 1991 vintage power plants in same market class and size. (2) Expected performance 60% efficiency and higher, (3) Emission levels, NO{sub x} < 10 ppM (0.15 lb/MW-h), CO < 20 ppM (0.30 lb/MW-h), and UHC < 20 ppM (0.30 lb/MW-h). ABB screening studies have identified the gas-fueled combined cycle as the most promising full scale solution to achieve the set goals for 1988--2002. This conclusion is based on ABB`s experience level, as well as the multi-step potential of the combined cycle process to improve in many component without introducing radical changes that might increase costs and lower RAM. The technical approach to achieve 60% or better thermal efficiency will include increased turbine inlet temperatures, compressor intercooling, as well a improvements in material, turbine cooling technology and the steam turbine. Use of improved component efficiencies will achieve gas-fired cycle performance of 61.78%. Conversion to coal-firing will result in system performance of 52.17%.

van der Linden, S.

1993-02-01T23:59:59.000Z

407

Climate system modeling on massively parallel systems: LDRD Project 95-ERP-47 final report  

Science Conference Proceedings (OSTI)

Global warming, acid rain, ozone depletion, and biodiversity loss are some of the major climate-related issues presently being addressed by climate and environmental scientists. Because unexpected changes in the climate could have significant effect on our economy, it is vitally important to improve the scientific basis for understanding and predicting the earth`s climate. The impracticality of modeling the earth experimentally in the laboratory together with the fact that the model equations are highly nonlinear has created a unique and vital role for computer-based climate experiments. However, today`s computer models, when run at desired spatial and temporal resolution and physical complexity, severely overtax the capabilities of our most powerful computers. Parallel processing offers significant potential for attaining increased performance and making tractable simulations that cannot be performed today. The principal goals of this project have been to develop and demonstrate the capability to perform large-scale climate simulations on high-performance computing systems (using methodology that scales to the systems of tomorrow), and to carry out leading-edge scientific calculations using parallelized models. The demonstration platform for these studies has been the 256-processor Cray-T3D located at Lawrence Livermore National Laboratory. Our plan was to undertake an ambitious program in optimization, proof-of-principle and scientific study. These goals have been met. We are now regularly using massively parallel processors for scientific study of the ocean and atmosphere, and preliminary parallel coupled ocean/atmosphere calculations are being carried out as well. Furthermore, our work suggests that it should be possible to develop an advanced comprehensive climate system model with performance scalable to the teraflops range. 9 refs., 3 figs.

Mirin, A.A.; Dannevik, W.P.; Chan, B.; Duffy, P.B.; Eltgroth, P.G.; Wehner, M.F.

1996-12-01T23:59:59.000Z

408

Prototype solar heating and cooling systems, including potable hot water. Quarterly report  

DOE Green Energy (OSTI)

The progress made in the development, delivery and support of two prototype solar heating and cooling systems including potable hot water is reported. The system consists of the following subsystems: collector, auxiliary heating, potable hot water, storage, control, transport, and government-furnished site data acquisition. Included is a comparison of the proposed Solaron-Heat Pump and Solaron-Desiccant Heating and Cooling Systems, Installation Drawings, data on the Akron House at Akron, Ohio, and other program activities from July 1, 1977 through November 9, 1977.

Not Available

1977-12-01T23:59:59.000Z

409

Energy Sources and Systems Analysis: 40 South Lincoln Redevelopment District (Full Report)  

SciTech Connect

This report presents the results of a case study to analyze district energy systems for their potential use in a project that involves redeveloping 270 units of existing public housing, along with other nearby sites. When complete, the redevelopment project will encompass more than 900 mixed-income residential units, commercial and retail properties, and open space. The analysis estimated the hourly heating, cooling, domestic hot water, and electric loads required by the community; investigated potential district system technologies to meet those needs; and researched available fuel sources to power such systems.

Not Available

2011-08-01T23:59:59.000Z

410

System and method for identifying, reporting, and evaluating presence of substance  

SciTech Connect

A system and method for identifying, reporting, and evaluating a presence of a solid, liquid, gas, or other substance of interest, particularly a dangerous, hazardous, or otherwise threatening chemical, biological, or radioactive substance. The system comprises one or more substantially automated, location self-aware remote sensing units; a control unit; and one or more data processing and storage servers. Data is collected by the remote sensing units and transmitted to the control unit; the control unit generates and uploads a report incorporating the data to the servers; and thereafter the report is available for review by a hierarchy of responsive and evaluative authorities via a wide area network. The evaluative authorities include a group of relevant experts who may be widely or even globally distributed.

Smith, Maurice (Kansas City, MO); Lusby, Michael (Kansas City, MO); Van Hook, Arthur (Lotawana, MO); Cook, Charles J. (Raytown, MO); Wenski, Edward G. (Lenexa, KS); Solyom, David (Overland Park, KS)

2012-02-14T23:59:59.000Z

411

System and method for identifying, reporting, and evaluating presence of substance  

DOE Patents (OSTI)

A system and method for identifying, reporting, and evaluating a presence of a solid, liquid, gas, or other substance of interest, particularly a dangerous, hazardous, or otherwise threatening chemical, biological, or radioactive substance. The system comprises one or more substantially automated, location self-aware remote sensing units; a control unit; and one or more data processing and storage servers. Data is collected by the remote sensing units and transmitted to the control unit; the control unit generates and uploads a report incorporating the data to the servers; and thereafter the report is available for review by a hierarchy of responsive and evaluative authorities via a wide area network. The evaluative authorities include a group of relevant experts who may be widely or even globally distributed.

Smith, Maurice (Kansas City, MO); Lusby, Michael (Kansas City, MO); Van Hook, Arthur (Lake Lotawana, MO); Cook, Charles J. (Raytown, MO); Wenski, Edward G. (Lenexa, KS); Solyom, David (Overland Park, KS)

2006-10-24T23:59:59.000Z

412

System And Method For Identifying, Reporting, And Evaluating Presence Of Substance  

DOE Patents (OSTI)

A system and method for identifying, reporting, and evaluating a presence of a solid, liquid, gas, or other substance of interest, particularly a dangerous, hazardous, or otherwise threatening chemical, biological, or radioactive substance. The system comprises one or more substantially automated, location self-aware remote sensing units; a control unit; and one or more data processing and storage servers. Data is collected by the remote sensing units and transmitted to the control unit; the control unit generates and uploads a report incorporating the data to the servers; and thereafter the report is available for review by a hierarchy of responsive and evaluative authorities via a wide area network. The evaluative authorities include a group of relevant experts who may be widely or even globally distributed.

Smith, Maurice (Kansas City, MO); Lusby, Michael (Kansas City, MO); Hook, Arthur Van (Lake Lotawana, MO); Cook, Charles J. (Raytown, MO); Wenski, Edward G. (Lenexa, KS); Solyom, David (Overland Park, KS)

2005-09-20T23:59:59.000Z

413

Development of Analytical and Computational Methods for the Strategic Power Infrastructure Defense (SPID) System: EPRI/DoD Complex I nteractive Networks/Systems Initiative: Second Annual Report  

Science Conference Proceedings (OSTI)

This report details the second-year research accomplishments for one of six research consortia established under the Complex Interactive Networks/Systems Initiative. This particular document discusses analytical and computational methods for the Strategic Power Infrastructure Defense (SPID) System.

2001-06-21T23:59:59.000Z

414

Context-Dependent Network Agents: EPRI/DoD Complex Interactive Networks/Systems Initiative: Second Annual Report  

Science Conference Proceedings (OSTI)

This report details the second-year research accomplishments for one of six research consortia established under the Complex Interactive Networks/Systems Initiative. This particular report presents progress on developing and demonstrating "context-dependent network agent" (CDNA) technology.

2001-06-21T23:59:59.000Z

415

Artificial heart development program. Volume I. System development. Phase III summary report  

SciTech Connect

The report documents efforts and results in the development of the power system portions of a calf implantable model of nuclear-powered artificial heart. The primary objective in developing the implantable model was to solve the packaging problems for total system implantation. The power systems portion is physically that portion of the implantable model between the Pu-238 heat sources and the blood pump ventricles. The work performed had two parallel themes. The first of these was the development of an integrated implantable model for bench and animal experiments plus design effort on a more advanced model. The second was research and development on components of the system done in conjunction with the development of the implantable model and to provide technology for incorporation into advanced models plus support to implantations, at the University of Utah, of the systems blood pumping elements when driven by electric motor. The efforts and results of implantable model development are covered, mainly, in the text of the report. The research and development efforts and results are reported, primarily, in the appendices (Vol. 2).

1977-01-01T23:59:59.000Z

416

A Greenhouse-Gas Information System: Monitoring and Validating Emissions Reporting and Mitigation  

SciTech Connect

This study and report focus on attributes of a greenhouse-gas information system (GHGIS) needed to support MRV&V needs. These needs set the function of such a system apart from scientific/research monitoring of GHGs and carbon-cycle systems, and include (not exclusively): the need for a GHGIS that is operational, as required for decision-support; the need for a system that meets specifications derived from imposed requirements; the need for rigorous calibration, verification, and validation (CV&V) standards, processes, and records for all measurement and modeling/data-inversion data; the need to develop and adopt an uncertainty-quantification (UQ) regimen for all measurement and modeling data; and the requirement that GHGIS products can be subjected to third-party questioning and scientific scrutiny. This report examines and assesses presently available capabilities that could contribute to a future GHGIS. These capabilities include sensors and measurement technologies; data analysis and data uncertainty quantification (UQ) practices and methods; and model-based data-inversion practices, methods, and their associated UQ. The report further examines the need for traceable calibration, verification, and validation processes and attached metadata; differences between present science-/research-oriented needs and those that would be required for an operational GHGIS; the development, operation, and maintenance of a GHGIS missions-operations center (GMOC); and the complex systems engineering and integration that would be required to develop, operate, and evolve a future GHGIS.

Jonietz, Karl K. [Los Alamos National Laboratory; Dimotakis, Paul E. [JPL/CAL Tech; Rotman, Douglas A. [Lawrence Livermore National Laboratory; Walker, Bruce C. [Sandia National Laboratory

2011-09-26T23:59:59.000Z

417

Advanced turbine systems program conceptual design and product development. Annual report, August 1993--July 1994  

SciTech Connect

This Yearly Technical Progress Report covers the period August 3, 1993 through July 31, 1994 for Phase 2 of the Advanced Turbine Systems (ATS) Program by Solar Turbines Incorporated under DOE Contract No. DE-AC421-93MC30246. As allowed by the Contract (Part 3, Section J, Attachment B) this report is also intended to fulfill the requirements for a fourth quarterly report. The objective of Phase 2 of the ATS Program is to provide the conceptual design and product development plan for an ultra-high efficiency, environmentally superior and cost-competitive industrial gas turbine system to be commercialized in the year 2000. During the period covered by this report, Solar has completed three of eight program tasks and has submitted topical reports. These three tasks included a Project Plan submission of information required by NEPA, and the selection of a Gas-Fueled Advanced Turbine System (GFATS). In the latest of the three tasks, Solar`s Engineering team identified an intercooled and recuperated (ICR) gas turbine as the eventual outcome of DOE`s ATS program coupled with Solar`s internal New Product Introduction (NPI) program. This machine, designated ``ATS50`` will operate at a thermal efficiency (turbine shaft power/fuel LHV) of 50 percent, will emit less than 10 parts per million of NOx and will reduce the cost of electricity by 10 percent. It will also demonstrate levels of reliability, availability, maintainability, and durability (RAMD) equal to or better than those of today`s gas turbine systems. Current activity is concentrated in three of the remaining five tasks a Market Study, GFATS System Definition and Analysis, and the Design and Test of Critical Components.

1994-11-01T23:59:59.000Z

418

Project Assessment & Reporting System (PARS II) Release Notes: Version 8.0.20120308  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Project Assessment & Project Assessment & Reporting System (PARS II) Release Notes: Version 8.0.20120308 Release Date: 05/19/2012 Achieving Management and Operational Excellence Page 2 PARS II - Enhancements New and improved functionality was released in Version 8.0.20120308 of PARS II. This release offers PARS II Users a significant number of enhancements across all facets of the application. These enhancements include additional refinements to the "look and feel" of the system. Enhancements are a result of community/User recommendations. System usability as well as providing improved means for data collection, validation and reporting were strategically designed and tested over the past several months. An explanation of each enhancement ,

419

Model documentation report: Residential sector demand module of the National Energy Modeling System  

SciTech Connect

This report documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code. This document serves three purposes. First, it is a reference document providing a detailed description for energy analysts, other users, and the public. Second, this report meets the legal requirement of the Energy Information Administration (EIA) to provide adequate documentation in support of its statistical and forecast reports according to Public Law 93-275, section 57(b)(1). Third, it facilitates continuity in model development by providing documentation from which energy analysts can undertake model enhancements, data updates, and parameter refinements.

NONE

1995-03-01T23:59:59.000Z

420

Model documentation report: Residential sector demand module of the National Energy Modeling System  

Science Conference Proceedings (OSTI)

This report documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code. This document serves three purposes. First, it is a reference document that provides a detailed description for energy analysts, other users, and the public. Second, this report meets the legal requirement of the Energy Information Administration (EIA) to provide adequate documentation in support of its statistical and forecast reports according to Public Law 93-275, section 57(b)(1). Third, it facilitates continuity in model development by providing documentation from which energy analysts can undertake model enhancements, data updates, and parameter refinements.

NONE

1997-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "reporting system psrs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Model documentation report: Transportation sector model of the National Energy Modeling System  

SciTech Connect

This report documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Transportation Model (TRAN). The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated by the model. This document serves three purposes. First, it is a reference document providing a detailed description of TRAN for model analysts, users, and the public. Second, this report meets the legal requirements of the Energy Information Administration (EIA) to provide adequate documentation in support of its statistical and forecast reports (Public Law 93-275, 57(b)(1)). Third, it permits continuity in model development by providing documentation from which energy analysts can undertake model enhancements, data updates, and parameter refinements.

Not Available

1994-03-01T23:59:59.000Z

422

SOLERAS - Solar Controlled Environment Agriculture Project. Final report, Volume 6. Science Applications, Incorporated system analysis  

Science Conference Proceedings (OSTI)

This report summarizes the results of the systems analysis task for the conceptual design of a commercial size, solar powered, controlled environment agriculture system. The baseline greenhouse system consists of a 5-hectare growing facility utilizing an innovative fluid roof filter concept to provide temperature and humidity control. Fresh water for the system is produced by means of a reverse osmosis desalination unit and energy is provided by means of a solar photovoltaic array in conjunction with storage batteries and a power conditioning unit. The greenhouse environment is controlled via circulation of brackish groundwater in a closed system, which permits water recovery during dehumidification as well as CO/sub 2/ enrichment for increased crop productivity.

Not Available

1985-01-01T23:59:59.000Z

423

Solar total energy systems final technical summary report. Volume I. Solar total energy systems market penetration  

SciTech Connect

The results of the market penetration analysis of Solar Total Energy Systems (STES) for the industrial sector are described. Performance data derived for STES commercial applications are included. The energy use and price forecasts used in the analysis are summarized. The STES Applications Model (SAM), has been used to develop data on STES development potential by state and industry as a function of time from 1985 through 2015. A second computer code, the Market Penetration Model (MPM), has been completed and used to develop forecasts of STES market penetration and national energy displacement by fuel type. This model was also used to generate sensitivity factors for incentives, and variations in assumptions of cost of STES competing fuel. Results for the STES performance analysis for commercial applications are presented. (MHR)

Bush, L.R.; Munjal, P.K.

1978-03-31T23:59:59.000Z

424

Analytical selection of marketable SAHP systems. Final report, September 30, 1977-December 31, 1979  

DOE Green Energy (OSTI)

For the effective marketing of energy conserving heating systems which have high initial costs, such as the solar assisted heat pump (SAHP), it is imperative to identify those climatic regions, load profiles, and system characteristics for which such systems are economically promising. This report summarizes efforts to develop a quick and efficient means of performing this identification. These efforts were separated into two distinct studies, a marketing study and a technical study of five energy conserving systems; and stand-alone heat pump, a stand-alone solar energy system, and a series, a parallel, and a dual source SAHP system. One of the primary results of the marketing study was the identification of the portion of the HVAC market into which the initial marketing thrust of these systems should be concentrated. In addition, several factors which influence the sales of these systems were identified. The technical study concentrated on the development and use of an analytical model of each of the systems. This model was designed to quickly size, in a specific climatic region, the system components for an economic optimum; i.e., for a minimum life cycle cost. Then the one energy conserving system which has the lowest life cycle cost, and thus the best potential, can be identified. It was found that, at present costs of electricity, the air-to-air heat pump has the lowest life cycle cost and hence is considered most marketable. At significantly higher electricity costs, the series SAHP system is the most marketable one because it has the lowest life cycle cost of the five energy conserving systems studied.

Kahan, W.

1980-01-01T23:59:59.000Z

425

Solar energy system performance evaluation - final report for Honeywell OTS 45, Salt River Project, Phoenix, Arizona  

DOE Green Energy (OSTI)

This report describes the operation and technical performance of the Solar Operational Test Site (OTS 45) at Salt River Project in Phoenix, Arizona, based on the analysis of data collected between April 1981 and March 31, 1982. The following topics are discussed: system description, performance assessment, operating energy, energy savings, system maintenance, and conclusions. The solar energy system at OTS 45 is a hydronic heating and cooling system consisting of 8208 square feet of liquid-cooled flat-plate collectors; a 2500-gallon thermal storage tank; two 25-ton capacity organic Rankine-cycle-engine-assisted water chillers; a forced-draft cooling tower; and associated piping, pumps, valves, controls and heat rejection equipment. The solar system has eight basic modes of operation and several combination modes. The system operation is controlled automatically by a Honeywell-designed microprocessor-based control system, which also provides diagnostics. Based on the instrumented test data monitored and collected during the 8 months of the Operational Test Period, the solar system collected 1143 MMBtu of thermal energy of the total incident solar energy of 3440 MMBtu and provided 241 MMBtu for cooling and 64 MMBtu for heating. The projected net annual electrical energy savings due to the solar system was approximately 40,000 kWh(e).

Mathur, A K

1983-09-01T23:59:59.000Z

426

Modeling and Verification of Distributed Generation and Voltage Regulation Equipment for Unbalanced Distribution Power Systems; Annual Subcontract Report, June 2007  

Science Conference Proceedings (OSTI)

This report summarizes the development of models for distributed generation and distribution circuit voltage regulation equipment for unbalanced power systems and their verification through actual field measurements.

Davis, M. W.; Broadwater, R.; Hambrick, J.

2007-07-01T23:59:59.000Z

427

Colorado State University Program for developing, testing, evaluating and optimizing solar heating systems. Project status report, April--May 1995  

DOE Green Energy (OSTI)

A project status report for April and May 1995 is given on the Colorado State University program on development of solar heating systems.

NONE

1995-06-01T23:59:59.000Z

428

SERF photovoltaic systems. Technical report on system performance for the period, August 1, 1994--July 31, 1995  

DOE Green Energy (OSTI)

This report presents an analysis of performance data on the two identical, 6 kW{sub ac}, grid-connected photovoltaic systems located on the roof of the Solar Energy Research Facility building at the National Renewable Energy Laboratory in Golden, Colorado. The data cover the monitoring period August 1, 1994, to July 31, 1995, and the performance parameters analyzed include direct current and alternating current power, aperture-area efficiency, energy, capacity factor, and performance index. These parameters are compared to plane-of-array irradiance, ambient temperature, and back-of-module temperature as a function of time, either daily or monthly. We also obtained power ratings of the systems for data corresponding to different test conditions. This study has shown, in addition to expected seasonal trends, that system monitoring is a valuable tool in assessing performance and detecting faulty equipment. Furthermore, methods applied for this analysis may be used to evaluate and compare systems using cells of different technologies. The systems were both found to be operating at approximately 7% below their estimated rating, which was based on Photovoltaics for Utility-Scale Applications test conditions. This may be attributed to the design inverter efficiency being estimated at 95% compared to measured values of approximately 88%, as well as the fact that aperture-area efficiency that was overestimated at 12.8% compared to a measured value of 11.0%. The continuous monitoring also revealed faulty peak-power point tracking equipment.

Dyk, E.E. van; Strand, T.R.; Hansen, R.

1996-06-01T23:59:59.000Z

429

HTGR applications program advanced systems. Semiannual report, October 1, 1982-March 31, 1983  

SciTech Connect

Work Breakdown Structure (WBS 41) activities emphasize the advanced HTGR modular reactor system (MRS) for reformer (R) and steam cycle/-cogeneration (SC/C) applications. This report describes progress in system performance for a 250-MW(t) MRS-R and a 300-MW(t) MRS-SC/C plant; it details the groundrules and parameters for the FY-83 nuclear core design and examines and compares fuel cycle economics. This report gives results from a study on decay heat removal transients for the MRS-R and MRS-SC/C variants. It evaluates the bypass valve system and the number and location of helium circulators, and it describes the progress on circulator component design, a prestressed concrete vessel steel closure design, and plant licensing and safety. Under the Advanced Technology Transfer Task (WBS 15), this report includes a section on a pebble bed reactor (PBR) MRS core heatup thermal model analysis. This report also gives the results of a survey on candidate reformer tube materials from GA Technologies Inc. to identify acceptable substitute materials for Inconel 617 to alleviate possible cobalt activation and carburization problems.

None

1983-05-01T23:59:59.000Z

430

Lockheed Martin Energy Systems, Inc., Groundwater Program Office. Annual report for fiscal year 1994  

Science Conference Proceedings (OSTI)

This edition of the Lockheed Martin Energy Systems, Inc., (Energy Systems) Groundwater Program Annual Report summarizes the work carried out by the Energy Systems Groundwater Program Office (GWPO) for fiscal year (FY) 1994. The GWPO is responsible for coordination and oversight for all components of the groundwater programs at the three Oak Ridge facilities [Oak Ridge National Laboratory (ORNL), the Oak Ridge Y-12 Plant, and the Oak Ridge K-25 Site], as well as the Paducah and Portsmouth Gaseous Diffusion Plants (PGDP and PORTS, respectively.) This report describes the administrative framework of the GWPO including staffing, organization, and funding sources. In addition, summaries are provided of activities involving the Technical Support staff at the five facilities. Finally, the results of basic investigations designed to improve our understanding of the major processes governing groundwater flow and contaminant migration on the Oak Ridge Reservation (ORR) are reported. These investigations are conducted as part of the Oak Ridge Reservation Hydrology and Geology Studies (ORRHAGS) program. The relevance of these studies to the overall remediation responsibilities of Energy Systems is discussed.

NONE

1994-09-30T23:59:59.000Z

431

Decontamination systems information and research program. Quarterly report, April--June 1995  

Science Conference Proceedings (OSTI)

West Virginia University (WVU) and the US Department of Energy Morgantown Energy Technology Center (DOE/METC) entered into a Cooperative Agreement on August 29, 1992 titled `Decontamination Systems Information and Research Programs`. Requirements stipulated by the Agreement require WVU to submit Technical Progress reports on a quarterly basis. This report contains the efforts of the fourteen research projects comprising the Agreement for the period April 1 to June 30, 1995. During this period three new projects have been funded by the Agreement. These projects are: (1) WERC National Design Contest, (2) Graduate Interns to the Interagency Environmental Technology Office under the National Science and Technology Council, and (3) WV High Tech Consortium.

NONE

1995-07-01T23:59:59.000Z

432

Advanced turbine systems program conceptual design and product development. Quarterly report, August--October 1995  

Science Conference Proceedings (OSTI)

This report describes the tasks completed for the advanced turbine systems program. The topics of the report include last row turbine blade development, single crystal blade casting development, ceramic materials development, combustion cylinder flow mapping, shroud film cooling, directional solidified valve development, shrouded blade cooling, closed-loop steam cooling, active tip clearance control, flow visualization tests, combustion noise investigation, TBC field testing, catalytic combustion development, optical diagnostics probe development, serpentine channel cooling tests, brush seal development, high efficiency compressor design, advanced air sealing development, advanced coating development, single crystal blade development, Ni-based disc forging development, and steam cooling effects on materials.

NONE

1996-01-01T23:59:59.000Z

433

Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1993  

SciTech Connect

This reports reports the progress/efforts performed on six technical projects: 1. systematic assessment of the state of hazardous waste clean-up technologies; 2. site remediation technologies (SRT):drain- enhanced soil flushing for organic contaminants removal; 3. SRT: in situ bio-remediation of organic contaminants; 4. excavation systems for hazardous waste sites: dust control methods for in-situ nuclear waste handling; 5. chemical destruction of polychlorinated biphenyls; and 6. development of organic sensors: monolayer and multilayer self-assembled films for chemical sensors.

Not Available

1993-04-01T23:59:59.000Z

434

A greenhouse-gas information system monitoring and validating emissions reporting and mitigation  

SciTech Connect

Current GHG-mitigating regimes, whether internationally agreed or self-imposed, rely on the aggregation of self-reported data, with limited checks for consistency and accuracy, for monitoring. As nations commit to more stringent GHG emissions-mitigation actions and as economic rewards or penalties are attached to emission levels, self-reported data will require independent confirmation that they are accurate and reliable, if they are to provide the basis for critical choices and actions that may be required. Supporting emissions-mitigation efforts and agreements, as well as monitoring energy- and fossil-fuel intensive national and global activities would be best achieved by a process of: (1) monitoring of emissions and emission-mitigation actions, based, in part, on, (2) (self-) reporting of pertinent bottom-up inventory data, (3) verification that reported data derive from and are consistent with agreed-upon processes and procedures, and (4) validation that reported emissions and emissions-mitigation action data are correct, based on independent measurements (top-down) derived from a suite of sensors in space, air, land, and, possibly, sea, used to deduce and attribute anthropogenic emissions. These data would be assessed and used to deduce and attribute measured GHG concentrations to anthropogenic emissions, attributed geographically and, to the extent possible, by economic sector. The validation element is needed to provide independent assurance that emissions are in accord with reported values, and should be considered as an important addition to the accepted MRV process, leading to a MRV&V process. This study and report focus on attributes of a greenhouse-gas information system (GHGIS) needed to support MRV&V needs. These needs set the function of such a system apart from scientific/research monitoring of GHGs and carbon-cycle systems, and include (not exclusively): the need for a GHGIS that is operational, as required for decision-support; the need for a system that meets specifications derived from imposed requirements; the need for rigorous calibration, verification, and validation (CV&V) standards, processes, and records for all measurement and modeling/data-inversion data; the need to develop and adopt an uncertainty-quantification (UQ) regimen for all measurement and modeling data; and the requirement that GHGIS products can be subjected to third-party questioning and scientific scrutiny. This report examines and assesses presently available capabilities that could contribute to a future GHGIS. These capabilities include sensors and measurement technologies; data analysis and data uncertainty quantification (UQ) practices and methods; and model-based data-inversion practices, methods, and their associated UQ. The report further examines the need for traceable calibration, verification, and validation processes and attached metadata; differences between present science-/research-oriented needs and those that would be required for an operational GHGIS; the development, operation, and maintenance of a GHGIS missions-operations center (GMOC); and the complex systems engineering and integration that would be required to develop, operate, and evolve a future GHGIS. Present monitoring systems would be heavily relied on in any GHGIS implementation at the outset and would likely continue to provide valuable future contributions to GHGIS. However, present monitoring systems were developed to serve science/research purposes. This study concludes that no component or capability presently available is at the level of technological maturity and readiness required for implementation in an operational GHGIS today. However, purpose-designed and -built components could be developed and implemented in support of a future GHGIS. The study concludes that it is possible to develop and provide a capability-driven prototype GHGIS, as part of a Phase-1 effort, within three years from project-funding start, that would make use of and integrate existing sensing and system capabilities. As part of a Phase-2 effort, a requirem

Jonietz, Karl K [Los Alamos National Laboratory; Dimotakis, Paul E [JPL/CAL TECH; Roman, Douglas A [LLNL; Walker, Bruce C [SNL

2011-09-26T23:59:59.000Z

435

Reports  

NLE Websites -- All DOE Office Websites (Extended Search)

Reports Reports About ESnet Overview ESnet Staff Governance Our Network Case Studies ESnet Strategic Plan ESnet Organizational Chart ESnet History Science Requirements Network Requirements Reviews Reports Careers Contact Us Technical Assistance: 1 800-33-ESnet (Inside the US) 1 800-333-7638 (Inside the US) 1 510-486-7600 (Globally) 1 510-486-7607 (Globally) Report Network Problems: trouble@es.net Provide Web Site Feedback: info@es.net Reports ESnet publishes reports from science network Program Requirements Reviews on a regular basis. View the most recent of these below. Sort by: Date | Author | Type 2012 Eli Dart, Brian Tierney, Editors, "Biological and Environmental Research Network Requirements Workshop, November 2012 - Final Report"", November 29, 2012, LBNL LBNL-6395E

436

Energy storage and power conditioning aspects of photovoltaic solar power systems. Volume I. First quarterly report  

SciTech Connect

Solar energy may be utilized as thermal energy or converted into electricity by solar cells. ERDA's National Photovoltaic Conversion Program is concerned with this latter approach and is currently sponsoring industrial programs for photovoltaic systems and devices. In one such program, Spectrolab, Inc., is charged with performing conceptual design and analysis of three photovoltaic solar power systems. The sizes of these three systems will cover the requirements of residential, commercial and electric utility central station applications. In addition to a solar cell array, photovoltaic power systems must also include an energy storage system to enable operation during periods of low insolation and a power conditioning system to control the dc power from the array and convert it into an ac waveshape compatible with existing electrical equipment. The Scientific Development Operation of Bechtel Corporation is participating in the Spectrolab program by compiling and studying data on the energy storage and power conditioning aspects of all three photovoltaic solar power systems and by the conceptual design of the system for electric utility central station applications. The results of the energy storage and power conditioning study effort are presented in this report. (W.D.M.)

1975-10-01T23:59:59.000Z

437

Energy storage and power conditioning aspects of photovoltaic solar power systems. Volume I. First quarterly report  

DOE Green Energy (OSTI)

Solar energy may be utilized as thermal energy or converted into electricity by solar cells. ERDA's National Photovoltaic Conversion Program is concerned with this latter approach and is currently sponsoring industrial programs for photovoltaic systems and devices. In one such program, Spectrolab, Inc., is charged with performing conceptual design and analysis of three photovoltaic solar power systems. The sizes of these three systems will cover the requirements of residential, commercial and electric utility central station applications. In addition to a solar cell array, photovoltaic power systems must also include an energy storage system to enable operation during periods of low insolation and a power conditioning system to control the dc power from the array and convert it into an ac waveshape compatible with existing electrical equipment. The Scientific Development Operation of Bechtel Corporation is participating in the Spectrolab program by compiling and studying data on the energy storage and power conditioning aspects of all three photovoltaic solar power systems and by the conceptual design of the system for electric utility central station applications. The results of the energy storage and power conditioning study effort are presented in this report. (W.D.M.)

Not Available

1975-10-01T23:59:59.000Z

438

Central Receiver Solar Thermal Power System, Phase 1. CDRL Item 10. Final technical progress report  

DOE Green Energy (OSTI)

Results of analysis and design efforts by McDonnell Douglas Astronautics Company (MDAC), Rocketdyne, Stearns-Roger, Inc., Sheldahl, Inc., and the University of Houston between 1 July 1975 and 30 June 1977 are summarized. This is the Final Technical Progress Report published on the Phase 1 Central Receiver Solar Thermal Power System contract. Historical summaries and final selection of 10-MWe pilot plant and 100-MWe commercial systems are presented, with emphasis on the collector field characteristics, overall system performance, selection of steam/feedwater operating conditions, and rationale for system and subsystem selection. The commercial and pilot plant designs, as well as the subsystem research experiment activities for the collector, receiver, and thermal storage subsystems are presented, including a historical summary, design summary, and a description of the overall SRE test program and major test results for each of the subsystems.

Hallet, Jr., R. W.; Gervais, R. L.

1978-05-01T23:59:59.000Z

439

In situ permeability modification using gelled polymer systems. Annual report, April 11, 1997--April 10, 1998  

Science Conference Proceedings (OSTI)

Results from a research program on the application of gelled polymer technology for in situ permeability modification are presented in this report. The objective of this technology when used with displacement processes such as waterflooding is to reduce the permeability in fractures and/or high permeability matrix zones to improve volumetric sweep efficiency of the displacement process. In production wells, the objective is to reduce water influx. The research program focused on five areas: Gel treatment in fractured systems; Gel treatment in carbonate rocks; In-depth placement of gels; Gel systems for application in carbon dioxide flooding; and Gel treatment in production wells. The research program is primarily an experimental program directed toward improving the understanding of gelled polymer systems and how these systems can be used to increase oil recovery from petroleum reservoirs. A summary of progress for research conducted in the second 12 month period of a 28 month program is described.

Green, D.W.; Willhite, G.P.; McCool, C.S.; Heppert, J.A.; Vossoughi, S.; Michnick, M.J.

1998-09-01T23:59:59.000Z

440

Advanced turbine systems program conceptual design and product development. Quarterly report, August--October, 1994  

SciTech Connect

The objective of Phase 2 of the Advanced Turbine Systems (ATS) Program is to provide the conceptual design and product development plan for an ultra-high efficiency, environmentally superior and cost competitive industrial gas turbine system to be commercialized by the year 2000. A secondary objective is to begin early development of technologies critical to the success of ATS. During this report period, the following tasks were completed: Market study; System definition and analysis; and Integrated program plans. Progress on Task 8, Design and Test of Critical Components, is also discussed. This particular task includes expanded materials and component research covering recuperators, combustion, autothermal fuel reformation, ceramics application and advanced gas turbine system controls.

1995-01-01T23:59:59.000Z