National Library of Energy BETA

Sample records for reporting code ew

  1. Duration Test Report for the Entegrity EW50 Wind Turbine

    SciTech Connect (OSTI)

    Smith, J.; Huskey, A.; Jager, D.; Hur, J.

    2012-12-01

    This report summarizes the results of a duration test that NREL conducted on the Entegrity EW50 wind turbine. This test was conducted in accordance with the International Electrotechnical Commissions' (IEC) standard, Wind Turbine Generator System Part 2: Design requirements for small wind turbines, IEC 61400-2 Ed.2.0, 2006-03.

  2. Wind Turbine Generator System Power Performance Test Report for the Entegrity EW50 Wind Turbine

    SciTech Connect (OSTI)

    Smith, J.; Huskey, A.; Jager, D.; Hur, J.

    2011-05-01

    Report on the results of the power performance test that the National Renewable Energy Laboratory (NREL) conducted on Entegrity Wind System Inc.'s EW50 small wind turbine.

  3. Wind Turbine Generator System Safety and Function Test Report for the Entegrity EW50 Wind Turbine

    SciTech Connect (OSTI)

    Smith, J.; Huskey, A.; Jager, D.; Hur, J.

    2012-11-01

    This report summarizes the results of a safety and function test that NREL conducted on the Entegrity EW50 wind turbine. This test was conducted in accordance with the International Electrotechnical Commissions' (IEC) standard, Wind Turbine Generator System Part 2: Design requirements for small wind turbines, IEC 61400-2 Ed.2.0, 2006-03.

  4. Report number codes

    SciTech Connect (OSTI)

    Nelson, R.N.

    1985-05-01

    This publication lists all report number codes processed by the Office of Scientific and Technical Information. The report codes are substantially based on the American National Standards Institute, Standard Technical Report Number (STRN)-Format and Creation Z39.23-1983. The Standard Technical Report Number (STRN) provides one of the primary methods of identifying a specific technical report. The STRN consists of two parts: The report code and the sequential number. The report code identifies the issuing organization, a specific program, or a type of document. The sequential number, which is assigned in sequence by each report issuing entity, is not included in this publication. Part I of this compilation is alphabetized by report codes followed by issuing installations. Part II lists the issuing organization followed by the assigned report code(s). In both Parts I and II, the names of issuing organizations appear for the most part in the form used at the time the reports were issued. However, for some of the more prolific installations which have had name changes, all entries have been merged under the current name.

  5. Nonlinear Analysis for Event Forewarning (NLAfEW)

    Energy Science and Technology Software Center (OSTI)

    2013-05-23

    The NLAfEW computer code analyses noisy, experimental data to forewarn of adverse events. The functionality of the analysis is a follows: It removes artifacts from the data, converts the continuous data value to discrete values, constructs time-delay embedding vectors, comparents the unique nodes and links in one graph, and determines event forewarning on the basis of several successive occurrences of one (or more) of the dissimilarity measures above a threshold.

  6. Edgestar: ENERGY STAR Referral (DEP400EW)

    Broader source: Energy.gov [DOE]

    DOE referred the matter of Edgestar-brand dehumidifier, model DEP400EW, to the EPA for appropriate action after DOE testing showed that the model does not meet the ENERGY STAR specification.

  7. Country Report on Building Energy Codes in Japan

    SciTech Connect (OSTI)

    Evans, Meredydd; Shui, Bin; Takagi, T.

    2009-04-15

    This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America (U.S.). This reports gives an overview of the development of building energy codes in Japan, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, and lighting) for commercial and residential buildings in Japan.

  8. Country Report on Building Energy Codes in Korea

    SciTech Connect (OSTI)

    Evans, Meredydd; McJeon, Haewon C.; Shui, Bin; Lee, Seung Eon

    2009-04-17

    This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America (U.S.). This reports gives an overview of the development of building energy codes in Korea, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, and lighting) for commercial buildings in Korea.

  9. Country Report on Building Energy Codes in China

    SciTech Connect (OSTI)

    Shui, Bin; Evans, Meredydd; Lin, H.; Jiang, Wei; Liu, Bing; Song, Bo; Somasundaram, Sriram

    2009-04-15

    This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America (U.S.). This reports gives an overview of the development of building energy codes in China, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope and HVAC) for commercial and residential buildings in China.

  10. Country Report on Building Energy Codes in Canada

    SciTech Connect (OSTI)

    Shui, Bin; Evans, Meredydd

    2009-04-06

    This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America . This reports gives an overview of the development of building energy codes in Canada, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, lighting, and water heating) for commercial and residential buildings in Canada.

  11. Country Report on Building Energy Codes in the United States

    SciTech Connect (OSTI)

    Halverson, Mark A.; Shui, Bin; Evans, Meredydd

    2009-04-30

    This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America (U.S.). This reports gives an overview of the development of building energy codes in U.S., including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, lighting, and water heating) for commercial and residential buildings in the U.S.

  12. Country Report on Building Energy Codes in Australia

    SciTech Connect (OSTI)

    Shui, Bin; Evans, Meredydd; Somasundaram, Sriram

    2009-04-02

    This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America (U.S.). This reports gives an overview of the development of building energy codes in Australia, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, and lighting) for commercial and residential buildings in Australia.

  13. Working Group Reports Calibration of Radiation Codes Used in...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Working Group Reports Calibration of Radiation Codes Used in Climate Models: Comparison of Clear-Sky Calculations with Observations from the Spectral Radiation Experiment and the ...

  14. Report on a workshop concerning code validation

    SciTech Connect (OSTI)

    None

    1996-12-01

    The design of wind turbine components is becoming more critical as turbines become lighter and more dynamically active. Computer codes that will reliably predict turbine dynamic response are, therefore, more necessary than before. However, predicting the dynamic response of very slender rotating structures that operate in turbulent winds is not a simple matter. Even so, codes for this purpose have been developed and tested in North America and in Europe, and it is important to disseminate information on this subject. The purpose of this workshop was to allow those involved in the wind energy industry in the US to assess the progress invalidation of the codes most commonly used for structural/aero-elastic wind turbine simulation. The theme of the workshop was, ``How do we know it`s right``? This was the question that participants were encouraged to ask themselves throughout the meeting in order to avoid the temptation of presenting information in a less-than-critical atmosphere. Other questions posed at the meeting are: What is the proof that the codes used can truthfully represent the field data? At what steps were the codes tested against known solutions, or against reliable field data? How should the designer or user validate results? What computer resources are needed? How do codes being used in Europe compare with those used in the US? How does the code used affect industry certification? What can be expected in the future?

  15. DOE Vehicle Technologies Program 2009 Merit Review Report - Safety Codes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Standards | Department of Energy Safety Codes and Standards DOE Vehicle Technologies Program 2009 Merit Review Report - Safety Codes and Standards Merit review of DOE Vehicle Technologies Program research efforts 2009_merit_review_10.pdf (386.56 KB) More Documents & Publications DOE Vehicle Technologies Program 2009 Merit Review Report - Technology Validation DOE Vehicle Technologies Program 2009 Merit Review Report - Technology Integration and Education DOE Vehicle Technologies

  16. Validation of the G-PASS code : status report.

    SciTech Connect (OSTI)

    Vilim, R. B.; Nuclear Engineering Division

    2009-03-12

    Validation is the process of determining whether the models in a computer code can describe the important phenomena in applications of interest. This report describes past work and proposed future work for validating the Gas Plant Analyzer and System Simulator (G-PASS) code. The G-PASS code was developed for simulating gas reactor and chemical plant system behavior during operational transients and upset events. Results are presented comparing code properties, individual component models, and integrated system behavior against results from four other computer codes. Also identified are two experiment facilities nearing completion that will provide additional data for individual component and integrated system model validation. The main goal of the validation exercise is to ready a version of G-PASS for use as a tool in evaluating vendor designs and providing guidance to vendors on design directions in nuclear-hydrogen applications.

  17. Electrolux: ENERGY STAR Referral (EW26SS70I*)

    Broader source: Energy.gov [DOE]

    DOE referred Electrolux room air conditioner model EW26SS70I* to EPA, brand manager of the ENERGY STAR program, for appropriate action after DOE testing revealed that the model does not meet ENERGY STAR requirements.

  18. RELAP5/MOD3 code manual: Summaries and reviews of independent code assessment reports. Volume 7, Revision 1

    SciTech Connect (OSTI)

    Moore, R.L.; Sloan, S.M.; Schultz, R.R.; Wilson, G.E.

    1996-10-01

    Summaries of RELAP5/MOD3 code assessments, a listing of the assessment matrix, and a chronology of the various versions of the code are given. Results from these code assessments have been used to formulate a compilation of some of the strengths and weaknesses of the code. These results are documented in the report. Volume 7 was designed to be updated periodically and to include the results of the latest code assessments as they become available. Consequently, users of Volume 7 should ensure that they have the latest revision available.

  19. Report on FY15 alloy 617 code rules development

    SciTech Connect (OSTI)

    Sham, Sam; Jetter, Robert I; Hollinger, Greg; Pease, Derrick; Carter, Peter; Pu, Chao; Wang, Yanli

    2015-09-01

    Due to its strength at very high temperatures, up to 950°C (1742°F), Alloy 617 is the reference construction material for structural components that operate at or near the outlet temperature of the very high temperature gas-cooled reactors. However, the current rules in the ASME Section III, Division 5 Subsection HB, Subpart B for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 650°C (1200°F) (Corum and Brass, Proceedings of ASME 1991 Pressure Vessels and Piping Conference, PVP-Vol. 215, p.147, ASME, NY, 1991). The rationale for this exclusion is that at higher temperatures it is not feasible to decouple plasticity and creep, which is the basis for the current simplified rules. This temperature, 650°C (1200°F), is well below the temperature range of interest for this material for the high temperature gas-cooled reactors and the very high temperature gas-cooled reactors. The only current alternative is, thus, a full inelastic analysis requiring sophisticated material models that have not yet been formulated and verified. To address these issues, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (EPP) analysis methods applicable to very high temperatures. The proposed rules for strain limits and creep-fatigue evaluation were initially documented in the technical literature (Carter, Jetter and Sham, Proceedings of ASME 2012 Pressure Vessels and Piping Conference, papers PVP 2012 28082 and PVP 2012 28083, ASME, NY, 2012), and have been recently revised to incorporate comments and simplify their application. Background documents have been developed for these two code cases to support the ASME Code committee approval process. These background documents for the EPP strain limits and creep-fatigue code cases are documented in this report.

  20. Building Energy Codes-Best Practices Report for APEC Economies...

    Open Energy Info (EERE)

    AgencyCompany Organization: The Building Codes Assistance Project (BCAP) Sector: Energy Focus Area: Energy Efficiency, Buildings Topics: Policiesdeployment programs Resource...

  1. Application of the Australian Geothermal Reporting Code to "Convention...

    Open Energy Info (EERE)

    This paper describes how the Code principles and the underlying resource estimation methodology have been applied in those cases. Some of the major issues which had to be...

  2. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode...

    Office of Environmental Management (EM)

    Record 992011 http:www.em.doe.govPagesgroundwaterReport.aspx?plumeCode175 Environmental Indicators (EIs) Groundwater Migration Under Control? Yes Confirmed by Lead...

  3. Changes to Geothermal Reporting Code and Guidelines on Company...

    Open Energy Info (EERE)

    Code. Authors G. Beardsmore, A. Budd, B. Goldstein, F. Holgate, G. Jeffress, A. Larking, J. Lawless, J. Libby, M. Middleton, P. Reid, C. Stafford, M. Ward and A. Williams...

  4. Final Technical Report: Hydrogen Codes and Standards Outreach

    SciTech Connect (OSTI)

    Hall, Karen I.

    2007-05-12

    This project contributed significantly to the development of new codes and standards, both domestically and internationally. The NHA collaborated with codes and standards development organizations to identify technical areas of expertise that would be required to produce the codes and standards that industry and DOE felt were required to facilitate commercialization of hydrogen and fuel cell technologies and infrastructure. NHA staff participated directly in technical committees and working groups where issues could be discussed with the appropriate industry groups. In other cases, the NHA recommended specific industry experts to serve on technical committees and working groups where the need for this specific industry expertise would be on-going, and where this approach was likely to contribute to timely completion of the effort. The project also facilitated dialog between codes and standards development organizations, hydrogen and fuel cell experts, the government and national labs, researchers, code officials, industry associations, as well as the public regarding the timeframes for needed codes and standards, industry consensus on technical issues, procedures for implementing changes, and general principles of hydrogen safety. The project facilitated hands-on learning, as participants in several NHA workshops and technical meetings were able to experience hydrogen vehicles, witness hydrogen refueling demonstrations, see metal hydride storage cartridges in operation, and view other hydrogen energy products.

  5. Material report in support to RCC-MRX code 2010 stainless steel parts and products

    SciTech Connect (OSTI)

    Ancelet, Olivier; Lebarbe, Thierry; Dubiez-Le Goff, Sophie; Bonne, Dominique; Gelineau, Odile

    2012-07-01

    This paper presents the Material Report dedicated to stainless steels parts and products issued by AFCEN (Association Francaise pour les regles de Conception et de Construction des Materiels des Chaudieres Electro-Nucleaires) in support to RCC-MRx 2010 Code. The RCC-MRx Code is the result of the merger of the RCC-MX 2008, developed in the context of the research reactor Jules Horowitz Reactor project, in the RCC-MR 2007, which set up rules applicable to the design of components operating at high temperature and to the Vacuum Vessel of ITER (a presentation of RCC-MRx 2010 Code is the subject of another paper proposed in this Congress; it explains in particular the status of this Code). This Material Report is part of a set of Criteria of RCC-MRx (this set of Criteria is under construction). The Criteria aim at explaining the design and construction rules of the Code. They cover analyses rules as well as part procurement, welding, methods of tests and examination and fabrication rules. The Material Report particularly provides justifications and explanations on requirements and features dealing with parts and products proposed in the Code. The Material Report contains the following information: Introduction of the grade(s): codes and standards and Reference Procurement Specifications covering parts and products, applications and experience gained, - Physical properties, - Mechanical properties used for design calculations (base metal and welds): basic mechanical properties, creep mechanical properties, irradiated mechanical properties, - Fabrication: experience gained, metallurgy, - Welding: weldability, experience gained during welding and repair procedure qualifications, - Non-destructive examination, - In-service behaviour. In the article, examples of data supplied in the Material Report dedicated to stainless steels will be exposed. (authors)

  6. Thermal analysis for CVL's: Part 2, Final report. [VuSymP code

    SciTech Connect (OSTI)

    Not Available

    1987-06-01

    This report documents work carried out for the Copper Vapor Laser (CVL) technology group in the Atomic Vapor Laser Isotope Separation (AVLIS) program at LLNL. The problems addressed in this subcontract have focused on the efficient calculation of thermal viewfactors in three-dimensional configurations. Part I of this report provides a detailed description of the algorithms employed in the VuSymP code which has been developed under this subcontract, and has been delivered to LLNL. This volume describes several enhancements of VuSymP which have been implemented to make the code more useful to the CVL group at LLNL.

  7. Annual Stock Assessment - CWT [Coded Wire Tag program] (USFWS), Annual Report 2007.

    SciTech Connect (OSTI)

    Pastor, Stephen M.

    2009-07-21

    In 1989 the Bonneville Power Administration (BPA) began funding the evaluation of production groups of juvenile anadromous fish not being coded-wire tagged for other programs. These groups were the 'Missing Production Groups'. Production fish released by the U.S. Fish and Wildlife Service (FWS) without representative coded-wire tags during the 1980s are indicated as blank spaces on the survival graphs in this report. This program is now referred to as 'Annual Stock Assessment - CWT'. The objectives of the 'Annual Stock Assessment' program are to: (1) estimate the total survival of each production group, (2) estimate the contribution of each production group to fisheries, and (3) prepare an annual report for USFWS hatcheries in the Columbia River basin. Coded-wire tag recovery information will be used to evaluate the relative success of individual brood stocks. This information can also be used by salmon harvest managers to develop plans to allow the harvest of excess hatchery fish while protecting threatened, endangered, or other stocks of concern. All fish release information, including marked/unmarked ratios, is reported to the Pacific States Marine Fisheries Commission (PSMFC). Fish recovered in the various fisheries or at the hatcheries are sampled to recover coded-wire tags. This recovery information is also reported to PSMFC. This report has been prepared annually starting with the report labeled 'Annual Report 1994'. Although the current report has the title 'Annual Report 2007', it was written in fall of 2008 using data available from RMIS that same year, and submitted as final in January 2009. The main objective of the report is to evaluate survival of groups which have been tagged under this ongoing project.

  8. Annual Coded Wire Tag Program; Missing Production Groups, 1996 Annual Report.

    SciTech Connect (OSTI)

    Pastor, Stephen M.

    1997-01-01

    In 1989 the Bonneville Power Administration (BPA) began funding the evaluation of production groups of juvenile anadromous fish not being coded-wire tagged for other programs. These groups were the ''Missing Production Groups''. Production fish released by the U.S. Fish and Wildlife Service (USFWS) without representative coded-wire tags during the 1980's are indicated as blank spaces on the survival graphs in this report. The objectives of the ''Missing Production Groups'' program are: (1) to estimate the total survival of each production group, (2) to estimate the contribution of each production group to various fisheries, and (3) to prepare an annual report for all USFWS hatcheries in the Columbia River basin. Coded-wire tag recovery information will be used to evaluate the relative success of individual brood stocks. This information can also be used by salmon harvest managers to develop plans to allow the harvest of excess hatchery fish while protecting threatened, endangered, or other stocks of concern. In order to meet these objectives, a minimum of one marked group of fish is necessary for each production release. The level of marking varies according to location, species, and age at release. In general, 50,000 fish are marked with a coded-wire tag (CWT) to represent each production release group at hatcheries below John Day Dam. More than 100,000 fish per group are usually marked at hatcheries above John Day Dam. All fish release information, including marked/unmarked ratios, is reported to the Pacific States Marine Fisheries Commission (PSMFC). Fish recovered in the various fisheries or at the hatcheries are sampled to recover coded-wire tags. This recovery information is also reported to PSMFC.

  9. Annual Coded Wire Tag Program : Missing Production Groups, 1995 Annual Report.

    SciTech Connect (OSTI)

    Pastor, Stephen M.

    1995-12-01

    In 1989 the Bonneville Power Administration (BPA) began funding the evaluation of production groups of juvenile anadromous fish not being coded-wire tagged for other programs. These groups were the ''Missing Production Groups''. Production fish released by the U.S. Fish and Wildlife Service (USFWS) without representative coded-wire tags during the 1980's are indicated as blank spaces on the survival graphs in this report. The objectives of the ''Missing Production Groups'' program are: (1) to estimate the total survival of each production group, (2) to estimate the contribution of each production group to various fisheries, and (3) to prepare an annual report for all USFWS hatcheries in the Columbia River Basin. Coded-wire tag recovery information will be used to evaluate the relative success of individual brood stocks. It can also be used by salmon harvest managers to develop plans to allow the harvest of excess hatchery fish while protecting threatened or endangered stocks. In order to meet these objectives, a minimum of one marked group of fish is necessary for each production release. The level of marking varies according to location, species, and age at release. In general, 50,000 fish are marked with a coded-wire tag (CWT) to represent each production release group at hatcheries below John Day Dam. Between 120,000 and 200,000 fish are marked for groups at hatcheries above John Day Dam. All fish release information, including marked/unmarked ratios, is reported to the Pacific States Marine Fisheries Commission (PSMFC). Fish recovered in the various fisheries or at the hatcheries are sampled to recover coded-wire tags. This recovery information is also reported to PSMFC.

  10. Comprehensive Report For Proposed Elevated Temperature Elastic Perfectly Plastic (EPP) Code Cases Representative Example Problems

    SciTech Connect (OSTI)

    Greg L. Hollinger

    2014-06-01

    Background: The current rules in the nuclear section of the ASME Boiler and Pressure Vessel (B&PV) Code , Section III, Subsection NH for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 1200F (650C)1. To address this issue, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (E-PP) analysis methods and which are expected to be applicable to very high temperatures. The proposed rules for strain limits and creep-fatigue evaluation were initially documented in the technical literature 2, 3, and have been recently revised to incorporate comments and simplify their application. The revised code cases have been developed. Task Objectives: The goal of the Sample Problem task is to exercise these code cases through example problems to demonstrate their feasibility and, also, to identify potential corrections and improvements should problems be encountered. This will provide input to the development of technical background documents for consideration by the applicable B&PV committees considering these code cases for approval. This task has been performed by Hollinger and Pease of Becht Engineering Co., Inc., Nuclear Services Division and a report detailing the results of the E-PP analyses conducted on example problems per the procedures of the E-PP strain limits and creep-fatigue draft code cases is enclosed as Enclosure 1. Conclusions: The feasibility of the application of the E-PP code cases has been demonstrated through example problems that consist of realistic geometry (a nozzle attached to a semi-hemispheric shell with a circumferential weld) and load (pressure; pipe reaction load applied at the end of the nozzle, including axial and shear forces, bending and torsional moments; through-wall transient temperature gradient) and design and operating conditions (Levels A, B and C).

  11. Status report on the 'Merging' of the Electron-Cloud Code POSINST with the 3-D Accelerator PIC CODE WARP

    SciTech Connect (OSTI)

    Vay, J.-L.; Furman, M.A.; Azevedo, A.W.; Cohen, R.H.; Friedman, A.; Grote, D.P.; Stoltz, P.H.

    2004-04-19

    We have integrated the electron-cloud code POSINST [1] with WARP [2]--a 3-D parallel Particle-In-Cell accelerator code developed for Heavy Ion Inertial Fusion--so that the two can interoperate. Both codes are run in the same process, communicate through a Python interpreter (already used in WARP), and share certain key arrays (so far, particle positions and velocities). Currently, POSINST provides primary and secondary sources of electrons, beam bunch kicks, a particle mover, and diagnostics. WARP provides the field solvers and diagnostics. Secondary emission routines are provided by the Tech-X package CMEE.

  12. Light Water Reactor Sustainability Program Status Report on the Grizzly Code Enhancements

    SciTech Connect (OSTI)

    Stephen R. Novascone; Benjamin W. Spencer; Jason D. Hales

    2013-09-01

    This report summarizes work conducted during fiscal year 2013 to work toward developing a full capability to evaluate fracture contour J-integrals to the Grizzly code. This is a progress report on ongoing work. During the next fiscal year, this capability will be completed, and Grizzly will be capable of evaluating these contour integrals for 3D geometry, including the effects of thermal stress and large deformation. A usable, limited capability has been developed, which is capable of evaluating these integrals on 2D geometry, without considering the effects of material nonlinearity, thermal stress or large deformation. This report presents an overview of the approach used, along with a demonstration of the current capability in Grizzly, including a comparison with an analytical solution.

  13. Synthesis Report on the Implementation of Building Energy Codes in China

    SciTech Connect (OSTI)

    Shui, Bin; Haiyan, Lin; Congu, Yu; Halverson, Mark A.; Bo, Song; Jingru, Liu; Evans, Meredydd; Xiajiao, Zhu; Siwei, Lang

    2011-03-31

    China building energy code and details to help improve building energy efficiency at global, national and local levels

  14. Final Report A Multi-Language Environment For Programmable Code Optimization and Empirical Tuning

    SciTech Connect (OSTI)

    Yi, Qing; Whaley, Richard Clint; Qasem, Apan; Quinlan, Daniel

    2013-11-23

    This report summarizes our effort and results of building an integrated optimization environment to effectively combine the programmable control and the empirical tuning of source-to-source compiler optimizations within the framework of multiple existing languages, specifically C, C++, and Fortran. The environment contains two main components: the ROSE analysis engine, which is based on the ROSE C/C++/Fortran2003 source-to-source compiler developed by Co-PI Dr.Quinlan et. al at DOE/LLNL, and the POET transformation engine, which is based on an interpreted program transformation language developed by Dr. Yi at University of Texas at San Antonio (UTSA). The ROSE analysis engine performs advanced compiler analysis, identifies profitable code transformations, and then produces output in POET, a language designed to provide programmable control of compiler optimizations to application developers and to support the parameterization of architecture-sensitive optimizations so that their configurations can be empirically tuned later. This POET output can then be ported to different machines together with the user application, where a POET-based search engine empirically reconfigures the parameterized optimizations until satisfactory performance is found. Computational specialists can write POET scripts to directly control the optimization of their code. Application developers can interact with ROSE to obtain optimization feedback as well as provide domain-specific knowledge and high-level optimization strategies. The optimization environment is expected to support different levels of automation and programmer intervention, from fully-automated tuning to semi-automated development and to manual programmable control.

  15. Final Report. An Integrated Partnership to Create and Lead the Solar Codes and Standards Working Group

    SciTech Connect (OSTI)

    Rosenthal, Andrew

    2013-12-30

    The DOE grant, “An Integrated Partnership to Create and Lead the Solar Codes and Standards Working Group,” to New Mexico State University created the Solar America Board for Codes and Standards (Solar ABCs). From 2007 – 2013 with funding from this grant, Solar ABCs identified current issues, established a dialogue among key stakeholders, and catalyzed appropriate activities to support the development of codes and standards that facilitated the installation of high quality, safe photovoltaic systems. Solar ABCs brought the following resources to the PV stakeholder community; Formal coordination in the planning or revision of interrelated codes and standards removing “stove pipes” that have only roofing experts working on roofing codes, PV experts on PV codes, fire enforcement experts working on fire codes, etc.; A conduit through which all interested stakeholders were able to see the steps being taken in the development or modification of codes and standards and participate directly in the processes; A central clearing house for new documents, standards, proposed standards, analytical studies, and recommendations of best practices available to the PV community; A forum of experts that invites and welcomes all interested parties into the process of performing studies, evaluating results, and building consensus on standards and code-related topics that affect all aspects of the market; and A biennial gap analysis to formally survey the PV community to identify needs that are unmet and inhibiting the market and necessary technical developments.

  16. Boil-off experiments with the EIR-NEPTUN Facility: Analysis and code assessment overview report

    SciTech Connect (OSTI)

    Aksan, S.N.; Stierli, F.; Analytis, G.T.

    1992-03-01

    The NEPTUN data discussed in this report are from core uncovery (boil-off) experiments designed to investigate the mixture level decrease and the heat up of the fuel rod simulators above the mixture level for conditions simulating core boil-off for a nuclear reactor under small break loss-of-coolant accident conditions. The first series of experiments performed in the NEPTUN test facility consisted of ten boil-off (uncovery) and one adiabatic heat-up tests. In these tests three parameters were varied: rod power, system pressure and initial coolant subcooling. The NEPTUN experiments showed that the external surface thermocouples do not cause a significant cooling influence in the rods to which they are attached under boil-off conditions. The reflooding tests performed later on indicated that the external surface thermocouples have some effect during reflooding for NEPTUN electrically heated rod bundle. Peak cladding temperatures are reduced by about 30--40C and quench times occur 20--70 seconds earlier than rods with embedded thermocouples. Additionally, the external surface-thermocouples give readings up to 20 K lower than those obtained with internal surface thermocouples (in the absence of external thermocouples) in the peak cladding temperature zone. Some of the boil-off data obtained from the NEPTUN test facility are used for the assessment of the thermal-hydraulic transient computer codes. These calculations were performed extensively using the frozen version of TRAC-BD1/MOD1 (version 22). A limited number of assessment calculations were done with RELAP5/MOD2 (version 36.02). In this report the main results and conclusions of these calculations are presented with the identification of problem areas in relation to models relevant to boil-off phenomena. On the basis of further analysis and calculations done, changing some of the models such as the bubbly/slug flow interfacial friction correlation which eliminate some of the problems are recommended.

  17. SPEAR-BETA fuel performance code system. Volume 1. General description. Final report. [BWR; PWR

    SciTech Connect (OSTI)

    Christensen, R.

    1982-04-01

    This document provides a general description of the SPEAR-BETA fuel reliability code system. Included is a discussion of the methodology employed and the structure of the code system, as well as discussion of the major components: the data preparation routines, the mechanistic fuel performance model, the mechanistic cladding failure model, and the statistical failure model.

  18. International Code Assessment and Applications Program: Summary of code assessment studies concerning RELAP5/MOD2, RELAP5/MOD3, and TRAC-B. International Agreement Report

    SciTech Connect (OSTI)

    Schultz, R.R.

    1993-12-01

    Members of the International Code Assessment Program (ICAP) have assessed the US Nuclear Regulatory Commission (USNRC) advanced thermal-hydraulic codes over the past few years in a concerted effort to identify deficiencies, to define user guidelines, and to determine the state of each code. The results of sixty-two code assessment reviews, conducted at INEL, are summarized. Code deficiencies are discussed and user recommended nodalizations investigated during the course of conducting the assessment studies and reviews are listed. All the work that is summarized was done using the RELAP5/MOD2, RELAP5/MOD3, and TRAC-B codes.

  19. Annual Coded Wire Tag Program; Washington Missing Production Groups, 1993 Annual Report.

    SciTech Connect (OSTI)

    Fuss, Howard J.; Hammer, Stanley A.; Kimbel, Mark A. (Washington Department of Fisheries, Olympia, WA)

    1994-03-01

    The intent of this project is to coded-wire tag at least one production group of each species at each Columbia Basin hatchery to provide a holistic assessment of survival and catch distribution over time.

  20. Non-US data compression and coding research. FASAC Technical Assessment Report

    SciTech Connect (OSTI)

    Gray, R.M.; Cohn, M.; Craver, L.W.; Gersho, A.; Lookabaugh, T.; Pollara, F.; Vetterli, M.

    1993-11-01

    This assessment of recent data compression and coding research outside the United States examines fundamental and applied work in the basic areas of signal decomposition, quantization, lossless compression, and error control, as well as application development efforts in image/video compression and speech/audio compression. Seven computer scientists and engineers who are active in development of these technologies in US academia, government, and industry carried out the assessment. Strong industrial and academic research groups in Western Europe, Israel, and the Pacific Rim are active in the worldwide search for compression algorithms that provide good tradeoffs among fidelity, bit rate, and computational complexity, though the theoretical roots and virtually all of the classical compression algorithms were developed in the United States. Certain areas, such as segmentation coding, model-based coding, and trellis-coded modulation, have developed earlier or in more depth outside the United States, though the United States has maintained its early lead in most areas of theory and algorithm development. Researchers abroad are active in other currently popular areas, such as quantizer design techniques based on neural networks and signal decompositions based on fractals and wavelets, but, in most cases, either similar research is or has been going on in the United States, or the work has not led to useful improvements in compression performance. Because there is a high degree of international cooperation and interaction in this field, good ideas spread rapidly across borders (both ways) through international conferences, journals, and technical exchanges. Though there have been no fundamental data compression breakthroughs in the past five years--outside or inside the United State--there have been an enormous number of significant improvements in both places in the tradeoffs among fidelity, bit rate, and computational complexity.

  1. Annual Coded Wire Tag Program; Washington Missing Production Groups, 1994 Annual Report.

    SciTech Connect (OSTI)

    Fuss, Howard J.; Ashbrook, Charmane; Doty, Daniel (Washington Department of Fish and Wildlife, Olympia, WA)

    1994-12-01

    The Bonneville Power Administration (BPA) funds the ``Annual Coded Wire Tag Program -- Missing Production Groups for Columbia River Hatcheries`` project. The Washington Department of Fish and Wildlife (WDFW) [formerly the Washington Department of Fisheries (WDF) and the Washington Department of Wildlife (WDW)], Oregon Department of Fish and Wildlife (ODFW) and the United States Fish and Wildlife Service (USFWS) all operate salmon and steelhead rearing programs in the Columbia River basin. The intent of the funding is to coded-wire tag at least one production group of each species at each Columbia Basin hatchery to provide a holistic assessment of survival and catch distribution over time. Data generated by this project contributes to WDFW`s obligations for representative tagging under the Endangered. Species Act (ESA) permit for operating Columbia Basin facilities. WDFW facilities operating outside the Snake River basin are required to have a Section 10, ``Incidental Take`` permit. Consistent with special conditions within this permit, WDFW has now reached it`s objective to tag representative groups from all WDFW Columbia Basin releases.

  2. 2012 Annual Report: Simulate and Evaluate the Cesium Transport and Accumulation in Fukushima-Area Rivers by the TODAM Code

    SciTech Connect (OSTI)

    Onishi, Yasuo; Yokuda, Satoru T.

    2013-03-28

    Pacific Northwest National Laboratory initiated the application of the time-varying, one-dimensional sediment-contaminant transport code, TODAM (Time-dependent, One-dimensional, Degradation, And Migration) to simulate the cesium migration and accumulation in the Ukedo River in Fukushima. This report describes the preliminary TODAM simulation results of the Ukedo River model from the location below the Ougaki Dam to the river mouth at the Pacific Ocean. The major findings of the 100-hour TODAM simulation of the preliminary Ukedo River modeling are summarized as follows:

  3. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode...

    Office of Environmental Management (EM)

    Plume) Remediation Contractor: SM Stoller Corp Report Last Updated: 2009 Contaminants Halogenated VOCsSVOCs Present? Yes VOC Name Concentration (ppb) Regulatory Driver Cleanup...

  4. Testing Impact?s Radiation Code (Technical Report) | SciTech...

    Office of Scientific and Technical Information (OSTI)

    Authors: Edis, T ; Cameron-Smith, P ; Grant, K E ; Bergmann, D ; Chuang, C C Publication Date: 2004-07-12 OSTI Identifier: 15014455 Report Number(s): UCRL-TR-205281 TRN: ...

  5. Emissions Inventory Report Summary: Reporting Requirements for the New Mexico Administrative Code, Title 20, Chapter 2, Part 73 (20 NMAC 2.73) for Calendar Year 2001

    SciTech Connect (OSTI)

    Margorie Stockton

    2003-04-01

    Los Alamos National Laboratory is subject to annual emissions-reporting requirements for regulated air contaminants under Title 20 of the New Mexico Administrative Code, Chapter 2, Part 73 (20.2.73 NMAC), Notice of Intent and Emissions Inventory Requirements. The applicability of the requirements is based on the Laboratory's potential to emit 100 tons per year of suspended particulate matter, nitrogen oxides, carbon monoxide, sulfur oxides, or volatile organic compounds. For calendar year 2001, the Technical Area 3 steam plant was the primary source of criteria air pollutants from the Laboratory, while research and development activities were the primary source of volatile organic compounds. Emissions of beryllium and aluminum were reported for activities permitted under 20.2.72 NMAC. Hazardous air pollutant emissions from chemical use for research and development activities were also reported.

  6. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=16

    Office of Environmental Management (EM)

    Shiprock Responsible DOE Office: Office of Environmental Management Plume Name: Shiprock Remediation Contractor: S. M. Stoller Corporation Report Last Updated: 2009 Contaminants Halogenated VOCs/SVOCs Present? No Fuel Present? No Metals Present? Yes Metal Name Metal Concentration (ppb) Regulatory Driver Cleanup Requirement Mn 8300 No Se 530 Yes 0.05 U 2600 Yes 0.044 Isotopes Present? Yes Isotope Name Isotope Activity (pCi/l) Regulatory Driver Cleanup Requirement Sr 11000 No Explosives Present?

  7. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=16

    Office of Environmental Management (EM)

    Old North Continent Responsible DOE Office: Office of Legacy Management Plume Name: Slick Rock - Old North Continent Remediation Contractor: Unknown Report Last Updated: 2009 Contaminants Halogenated VOCs/SVOCs Present? No Fuel Present? No Metals Present? Yes Metal Name Metal Concentration (ppb) Regulatory Driver Cleanup Requirement Se 11.55 Yes 10 U 616.5 Yes 440 Isotopes Present? No Explosives Present? Yes Other Contaminants?No Tritium Present? No Nitrates Present? No Sulfates Present? No

  8. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=16

    Office of Environmental Management (EM)

    Union Carbide Responsible DOE Office: Office of Environmental Management Plume Name: Slick Rock - Union Carbide Remediation Contractor: Unknown Report Last Updated: 2009 Contaminants Halogenated VOCs/SVOCs Present? No Fuel Present? No Metals Present? Yes Metal Name Metal Concentration (ppb) Regulatory Driver Cleanup Requirement Se 2600 Yes 180 Mo 2200 Yes 100 U 111 Yes 44 Isotopes Present? No Explosives Present? Yes Other Contaminants?No Tritium Present? No Nitrates Present? Yes Concentration:

  9. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=17

    Office of Environmental Management (EM)

    Spook Responsible DOE Office: Office of Environmental Management Plume Name: Spook Remediation Contractor: Unknown Report Last Updated: 2009 Contaminants Halogenated VOCs/SVOCs Present? No Fuel Present? No Metals Present? Yes Metal Name Metal Concentration (ppb) Regulatory Driver Cleanup Requirement Cr (total) No Se 0 No U No Isotopes Present? Yes Isotope Name Isotope Activity (pCi/l) Regulatory Driver Cleanup Requirement other (provide names) Ra-226 No other (provide names) Ra-228 No Explosives

  10. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=17

    Office of Environmental Management (EM)

    Tuba City Responsible DOE Office: Office of Legacy Management Plume Name: Tuba City Remediation Contractor: Unknown Report Last Updated: 2009 Contaminants Halogenated VOCs/SVOCs Present? No Fuel Present? No Metals Present? Yes Metal Name Metal Concentration (ppb) Regulatory Driver Cleanup Requirement Se 50 Yes 10 Mo 300 Yes 100 U 250 Yes 44 Isotopes Present? No Explosives Present? Yes Other Contaminants?No Tritium Present? No Nitrates Present? Yes Concentration: 1000 (ppb) Regulatory Driver: Yes

  11. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=17

    Office of Environmental Management (EM)

    Legacy Management Plume Name: Chemical Plant (Quarry) Remediation Contractor: SM Stoller Report Last Updated: 2009 Contaminants Halogenated VOCs/SVOCs Present? No Fuel Present? No Metals Present? Yes Metal Name Metal Concentration (ppb) Regulatory Driver Cleanup Requirement U 3486 Yes 30 Isotopes Present? No Explosives Present? Yes Explosive Name Explosive Concentration (ppb) Regulatory Driver Cleanup Requirement DNT (dinitrotoluene) 9.3 Yes 0.11 Other Contaminants?No Tritium Present? No

  12. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=17

    Office of Environmental Management (EM)

    VOC) Remediation Contractor: Unknown Report Last Updated: Unknown Contaminants Halogenated VOCs/SVOCs Present? Yes VOC Name Concentration (ppb) Regulatory Driver Cleanup Requirement TCE No Fuel Present? No Metals Present? No Isotopes Present? No Explosives Present? No Other Contaminants?No Tritium Present? No Nitrates Present? No Sulfates Present? No Hydrogeology Conduit Flow? Yes Multiple Units Affected? No Depth (feet): Avg Velocity (feet/year): Plume Information (no source) Source Plume

  13. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=17

    Office of Environmental Management (EM)

    West Plume) Remediation Contractor: SM Stoller Corp Report Last Updated: 2009 Contaminants Halogenated VOCs/SVOCs Present? Yes VOC Name Concentration (ppb) Regulatory Driver Cleanup Requirement TCE 763 Yes 5 Fuel Present? No Metals Present? Yes Metal Name Metal Concentration (ppb) Regulatory Driver Cleanup Requirement U 264 Yes 20 Isotopes Present? No Explosives Present? Yes Explosive Name Explosive Concentration (ppb) Regulatory Driver Cleanup Requirement DNT (dinitrotoluene) Yes 0.11 Other

  14. Pedigree Analysis of the MELCOR 1.8.2 Code to be Used for ITER’s Report Preliminary on Safety

    SciTech Connect (OSTI)

    Richard L. Moore; Brad J. Merrill

    2007-06-01

    This report documents the pedigree analysis of the MELCOR 1.8.2 code to be used for ITER’s Report Preliminary on Safety. To pedigree the code the process involved four steps. First, taking the modified MELCOR 1.8.2 code used by the ITER Joint Central Team (JCT) for analyses in previous ITER Safety Assessments and compared the FORTRAN code of this version line-by-line to the original 1.8.2 version of MELCOR. The second step was a non-regression analysis which involves comparing the results from the pedigreed version against those predicted by the original, unmodified version of MELCOR 1.8.2. The third step involved comparing the pedigreed version results to results from the MELCOR version used by the ITER JCT for the Generic Site Safety Report (GSSR) against a set of accident problems analyzed for the safety report. The fourth and final step involved a comparison between the pedigreed version of the code and the developmental test problems cited in the change documents referenced in this report. The results from the pedigree process are described in this report.

  15. http://www.em.doe.gov/Pages/groundwaterReport.aspx?plumeCode=17

    Office of Environmental Management (EM)

    East Plume) Remediation Contractor: Unknown Report Last Updated: 2009 Contaminants Halogenated VOCs/SVOCs Present? No Fuel Present? No Metals Present? No Isotopes Present? No Explosives Present? No Explosive Name Explosive Concentration (ppb) Regulatory Driver Cleanup Requirement TNT (trinitrotoluene) 21 Yes 2.8 other (provide names) 2,4-DNT 200 Yes 0.11 other (provide names) 2,6-DNT 222 Yes 1.3 other (provide names) 1,3-DNB 0.16 Yes 1 Other Contaminants?No Tritium Present? No Nitrates Present?

  16. Emissions Inventory Report Summary: Reporting Requirements for the New Mexico Administrative code, Title 20, Chapter 2, Part 73 (20 NMAC 2.73) for Calendar Year 1997

    SciTech Connect (OSTI)

    1999-01-01

    Los Alamos National Laboratory (the Laboratory) is subject to emissions reporting requirements for regulated air contaminants under Title 20 of the New Mexico Administrative Code, Chapter 2, Part 73, (20 NMAC 2.73), Notice of Intent and Emissions Inventory Requirements. The Laboratory has the potential to emit 100 tons per year of suspended particulate matter (PM), nitrogen oxides (NO{sub x}), carbon monoxide (CO), and volatile organic compounds (VOCs). For 1997, combustion products from the industrial sources contributed the greatest amount of regulated air emissions from the Laboratory. Research and development activities contributed the greatest amount of VOCs. Emissions of beryllium and aluminum were reported for activities permitted under 20 NMAC 2.72, Construction Permits.

  17. Emissions Inventory Report Summary Reporting Requirements for the New Mexico Administrative Code, Title 20, Chapter 2, Part 73 (20 NMAC 2.73) for Calendar Year 1998

    SciTech Connect (OSTI)

    Air Quality Group, ESH-17

    1999-09-01

    Los Alamos National Laboratory (the Laboratory) is subject to emissions reporting requirements for regulated air contaminants under Title 20 of the New Mexico Administrative Code, Chapter 2, Part 73 (20 NMAC 2.73), Notice of Intent and Emissions Inventory Requirements. The Laboratory has the potential to emit 100 tons per year of suspended particulate matter, nitrogen oxides, carbon monoxide, sulfur oxides, and volatile organic compounds. For 1998, combustion products from the industrial sources contributed the greatest amount of criteria air pollutants from the Laboratory. Research and development activities contributed the greatest amount of volatile organic compounds. Emissions of beryllium and aluminum were reported for activities permitted under 20 NMAC 2.72 Construction Permits.

  18. Code Tables | National Nuclear Security Administration | (NNSA)

    National Nuclear Security Administration (NNSA)

    Code Tables U.S. Department of Energy / U.S. Nuclear Regulatory Commission Nuclear Materials Management & Safeguards System Code Tables Action Code The action code identifies the type of activity being reported in a transaction. The Action Code table shows the valid action codes. Nature of Transaction (TI) Code The financial code signifies the nature of the financial or contractual activity that is involved in the transaction. The Nature of Transaction (TI) Code table shows the valid action

  19. Emissions Inventory Report Summary: Reporting Requirements for the New Mexico Administrative Code, Title 20, Chapter 2, Part 73 (20.2.73 NMAC) for Calendar Year 2003

    SciTech Connect (OSTI)

    M. Stockton

    2005-01-01

    Los Alamos National Laboratory is subject to annual emissions-reporting requirements for regulated air pollutants under Title 20 of the New Mexico Administrative Code, Chapter 2, Part 73 (20.2.73 NMAC), Notice of Intent and Emissions Inventory Requirements. The applicability of the requirements is based on the Laboratory's potential to emit 100 tons per year of suspended particulate matter, nitrogen oxides, carbon monoxide, sulfur oxides, or volatile organic compounds. For calendar year 2003, the Technical Area 3 steam plant and the air curtain destructors were the primary sources of criteria air pollutants from the Laboratory, while the air curtain destructors and chemical use associated with research and development activities were the primary sources of volatile organic compounds and hazardous air pollutants. Emissions of beryllium and aluminum were reported for activities permitted under 20.2.72 NMAC. Hazardous air pollutant emissions were reported from chemical use as well as from all combustion sources. In addition, estimates of particulate matter with diameter less than 2.5 micrometers and ammonia were provided as requested by the New Mexico Environment Department, Air Quality Bureau.

  20. User's manual to the ICRP Code: a series of computer programs to perform dosimetric calculations for the ICRP Committee 2 report

    SciTech Connect (OSTI)

    Watson, S.B.; Ford, M.R.

    1980-02-01

    A computer code has been developed that implements the recommendations of ICRP Committee 2 for computing limits for occupational exposure of radionuclides. The purpose of this report is to describe the various modules of the computer code and to present a description of the methods and criteria used to compute the tables published in the Committee 2 report. The computer code contains three modules of which: (1) one computes specific effective energy; (2) one calculates cumulated activity; and (3) one computes dose and the series of ICRP tables. The description of the first two modules emphasizes the new ICRP Committee 2 recommendations in computing specific effective energy and cumulated activity. For the third module, the complex criteria are discussed for calculating the tables of committed dose equivalent, weighted committed dose equivalents, annual limit of intake, and derived air concentration.

  1. Occupational Radiation Protection Record-Keeping and Reporting Guide for use with Title 10, Code of Federal Regulations, Part 835, Occupational Radiation Protection

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1999-05-20

    This Guide provides an acceptable methodology for establishing and operating an occupational radiation protection record-keeping and reporting program that will comply with U.S. Department of Energy (DOE) requirements specified in Title 10 of the Code of Federal Regulations (CFR), Part 835, Occupational Radiation Protection. Canceled by DOE G 441.1-1B.

  2. XSOR codes users manual

    SciTech Connect (OSTI)

    Jow, Hong-Nian; Murfin, W.B.; Johnson, J.D.

    1993-11-01

    This report describes the source term estimation codes, XSORs. The codes are written for three pressurized water reactors (Surry, Sequoyah, and Zion) and two boiling water reactors (Peach Bottom and Grand Gulf). The ensemble of codes has been named ``XSOR``. The purpose of XSOR codes is to estimate the source terms which would be released to the atmosphere in severe accidents. A source term includes the release fractions of several radionuclide groups, the timing and duration of releases, the rates of energy release, and the elevation of releases. The codes have been developed by Sandia National Laboratories for the US Nuclear Regulatory Commission (NRC) in support of the NUREG-1150 program. The XSOR codes are fast running parametric codes and are used as surrogates for detailed mechanistic codes. The XSOR codes also provide the capability to explore the phenomena and their uncertainty which are not currently modeled by the mechanistic codes. The uncertainty distributions of input parameters may be used by an. XSOR code to estimate the uncertainty of source terms.

  3. Compiling Codes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    wrappers will automatically provide the necessary MPI include files and libraries. For Fortran source code use mpif90: % mpif90 -o example.x example.f90 For C source code use...

  4. Multispecies Diffusion Capability For The AMP Nuclear Fuel Performance Code (LANL Milestone M31MS060301 Final Report)

    SciTech Connect (OSTI)

    Dilts, Gary A.

    2012-03-29

    This work addresses only diffusion. The contact solver in AMP was not sufficiently developed this year to attempt treatment of species contact. A cylindrical tensor diffusion coefficient model was added to the AMP code, with the KHHS model [1] implemented into the AMP material library as a specific example. A cylindrical tensor diffusion operator manufactured solution verification example was coded. Before meeting the full text of the milestone task, it remains to: (1) code and run a cylindrical tensor diffusion solver manufactured solution (2) code and run the validation example of [1] (3) document results. These are dependent on developing new capabilities for the AMP code requiring close collaboration with the AMP team at ORNL. The model implemented provides a good intermediate first step toward a general multi-species solver. The multi-species capability of the AMP nuclear fuel code [2] is intended to allow the modeling of radiation-driven redistribution of various elements through solid metal nuclear reactor fuels. The initial model AMP provides for U-Pu-Zr fuels is based on the analysis of the Integral Fast Reactor (IFR) fuel development program experiment X419 post-irradiation data described in [1], referred to here as the KHHS model. This model may be specific to that experiment, but it was thought to provide a good start for the AMP code, because it (1) is formulated at the engineering scale, (2) decouples the species from each other, (3) predetermines the phase boundaries so that reference to a phase diagram is not needed, and (4) one of the authors (Hayes) was the NEAMS Fuels IPSC manager for FY11. The KHHS model is formulated for radial fluxes as little axial redistribution is seen experimentally. As U-Pu-Zr fuel is irradiated, the constituents migrate to form three annular regions. The center region is Zr-enriched and U-depleted, the middle region is Zr-depleted and U-enriched, and the outer region is Zr-enriched and U-depleted. The Pu concentration

  5. NAICS Codes @ Headquarters | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NAICS Codes @ Headquarters NAICS Codes @ Headquarters A listing of NAICS codes used at Headquarters Procurement Services NAICS Codes @ Headquarters.pdf (37.93 KB) More Documents & Publications Product Service Codes @ Headquarters Management & Operating Subcontract Reporting Capability (MOSRC) Downloads Historical Procurement Information

  6. Evaulation of power-reactor fuel-rod-analysis capabilities. Phase 1 topical report. Volume 2. Code evaluation. [PWR; BWR

    SciTech Connect (OSTI)

    Coleman, D.R.

    1983-09-01

    FRAPCON-2 (V1M4) was applied to generate fuel performance predictions for 60 rods of a recently evaluated power reactor data sample. Rod design, operational, and performance data was obtained from the RPRI Fuel Performance Data Base. The data was systematically processed to generate code input parameters. FRAPCON was initially applied for scoping studies to identify the best estimate mechanical response and fission gas release modeling options. Based on final scoping results, the balance of rods were analyzed with FRACAS-2 mechanics and FASTGRASS gas release models. Comparisons between measured and calculated fuel and cladding deformation, fission gas release, internal pressure, and gas composition are presented and interpreted relative to code error magnitudes, distributions, and trends versus rod design and operating parameters. The results indicate the FRAPCON-2 has best estimate capability for analysis of moderate duty fuel rod performance, provided that rod fabrication parameters are well characterized, and the fuel is dimensionally stable.

  7. Analysis of fission gas release measurements using the COMETHE IIIJ and FCODE-Alpha computer codes. Final report. [PWR; BWR

    SciTech Connect (OSTI)

    Leppert, G.; Rayes, L.; Rumble, E.; Stuart, R.

    1981-07-01

    Fission gas release predictions from FCODE-Alpha and COMETHE IIIJ were compared with experimental data from a representative group of light water reactor (LWR) fuel rods and with each other. In the first phase of the study, standard versions of the codes obtained from the Electric Power Software Center were compared with data from 36 rods. A modified version of COMETHE was used in the second phase of the study, which compared measurements from some of the same rods studied in the first phase, as well as with an additional 27 rods. Fission gas release predictions from both codes show substantial deviation from experimental measurements, and additional well-qualified data from LWR's is needed for comparison. Unpressurized rods experience significant degradation in heat transfer across the fuel-to-cladding gap as the lower thermal conductivity fission gases mix with the helium.

  8. Status report on multigroup cross section generation code development for high-fidelity deterministic neutronics simulation system.

    SciTech Connect (OSTI)

    Yang, W. S.; Lee, C. H.

    2008-05-16

    Under the fast reactor simulation program launched in April 2007, development of an advanced multigroup cross section generation code was initiated in July 2007, in conjunction with the development of the high-fidelity deterministic neutron transport code UNIC. The general objectives are to simplify the existing multi-step schemes and to improve the resolved and unresolved resonance treatments. Based on the review results of current methods and the fact that they have been applied successfully to fast critical experiment analyses and fast reactor designs for last three decades, the methodologies of the ETOE-2/MC{sup 2}-2/SDX code system were selected as the starting set of methodologies for multigroup cross section generation for fast reactor analysis. As the first step for coupling with the UNIC code and use in a parallel computing environment, the MC{sup 2}-2 code was updated by modernizing the memory structure and replacing old data management package subroutines and functions with FORTRAN 90 based routines. Various modifications were also made in the ETOE-2 and MC{sup 2}-2 codes to process the ENDF/B-VII.0 data properly. Using the updated ETOE-2/MC{sup 2}-2 code system, the ENDF/B-VII.0 data was successfully processed for major heavy and intermediate nuclides employed in sodium-cooled fast reactors. Initial verification tests of the MC{sup 2}-2 libraries generated from ENDF/B-VII.0 data were performed by inter-comparison of twenty-one group infinite dilute total cross sections obtained from MC{sup 2}-2, VIM, and NJOY. For almost all nuclides considered, MC{sup 2}-2 cross sections agreed very well with those from VIM and NJOY. Preliminary validation tests of the ENDF/B-VII.0 libraries of MC{sup 2}-2 were also performed using a set of sixteen fast critical benchmark problems. The deterministic results based on MC{sup 2}-2/TWODANT calculations were in good agreement with MCNP solutions within {approx}0.25% {Delta}{rho}, except a few small LANL fast assemblies

  9. EW;, Elwrcnrren1

    Office of Legacy Management (LM)

    W. Alexander Williams Designation and Certification Manager Off-Site Branch (EM-4211 ... Subject: VERIFICATION AND DESIGNATION SURVEYS: BAKER AfJD WILLIAMS WAREHOUSES Dear Dr. ...

  10. Single Use Letter Report for the Verification and Validation of the RADNUC-2A and ORIGEN2 S.2 Computer Codes

    SciTech Connect (OSTI)

    PACKER, M.J.

    2000-06-20

    This report documents the verification and validation (V&V) activities undertaken to support the use of the RADNUC2-A and ORIGEN2 S.2 computer codes for the specific application of calculating isotopic inventories and decay heat loadings for Spent Nuclear Fuel Project (SNFP) activities as described herein. Two recent applications include the reports HNF-SD-SNF-TI-009, 105-K Basin Material Design Basis Feed Description for Spent Nuclear Fuel Project Facilities, Volume 1, Fuel (Praga, 1998), and HNF-3035, Rev. 0B, MCO Gas Composition for Low Reactive Surface Areas (Packer, 1998). Representative calculations documented in these two reports were repeated using RADNUC2-A, and the results were identical to the documented results. This serves as verification that version 2A of Radnuc was used for the applications noted above; the same version was tested herein, and perfect agreement was shown. Comprehensive V&V is demonstrated for RADNUC2-A in Appendix A.

  11. Risk Code?

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Identify the Task Risk Code >2 Determine if a Work Control Document is needed What is the Unmitigated Risk Code? Rev.1 09/05/14 Read and Agree to Comply with appropriate mitigation and sign Work Control Documents Is there an approved Work Control Document (WCD)? WORK PLANNING, CONTROL AND AUTHORIZATION FLOW DIAGRAM 1. Define Scope of Work 2. Analyze Hazards 3. Develop and Implement Hazard Controls 4. Perform Work Within Controls 5. Feedback and Continuous Improvement Analyze Hazards and

  12. Tornado missile simulation and design methodology. Volume 1: simulation methodology, design applications, and TORMIS computer code. Final report

    SciTech Connect (OSTI)

    Twisdale, L.A.; Dunn, W.L.

    1981-08-01

    A probabilistic methodology has been developed to predict the probabilities of tornado-propelled missiles impacting and damaging nuclear power plant structures. Mathematical models of each event in the tornado missile hazard have been developed and sequenced to form an integrated, time-history simulation methodology. The models are data based where feasible. The data include documented records of tornado occurrence, field observations of missile transport, results of wind tunnel experiments, and missile impact tests. Probabilistic Monte Carlo techniques are used to estimate the risk probabilities. The methodology has been encoded in the TORMIS computer code to facilitate numerical analysis and plant-specific tornado missile probability assessments. Sensitivity analyses have been performed on both the individual models and the integrated methodology, and risk has been assessed for a hypothetical nuclear power plant design case study.

  13. Evaluation of flow redistribution due to flow blockage in rod bundles using COBRA code simulation. Final report. [PWR

    SciTech Connect (OSTI)

    Prelewicz, D.A.; Caruso, M.A.

    1981-01-01

    During a Loss-of-Coolant Accident, fuel rod cladding may reach temperatures approaching 2200/sup 0/F. At these temperatures, swelling and rupture of the cladding may occur. The resulting flow blockage will affect steam flow and heat transfer in the bundle during the period of reflooding. The COBRA-IV-I subchannel computer code was used to simulate flow redistribution due to sleeve blockages in the FLECHT-SEASET 21-rod bundle and plate blockages in the JAERI Slab Core Test Facility. Sensitivity studies were conducted to determine the effects of spacer grid and blockage interaction, sleeve shape effects, sleeve length effects, blockage magnitude and distribution, thermally induced mixing and bundle average velocity on flow redistribution. Pressure drop due to sleeve blockages was also calculated for several blockage configurations.

  14. Safety, Codes and Standards Technical Publications

    Broader source: Energy.gov [DOE]

    Technical information about safety, codes and standards published in technical reports, conference proceedings, journal articles, and websites is provided here.

  15. Speech coding

    SciTech Connect (OSTI)

    Ravishankar, C., Hughes Network Systems, Germantown, MD

    1998-05-08

    Speech is the predominant means of communication between human beings and since the invention of the telephone by Alexander Graham Bell in 1876, speech services have remained to be the core service in almost all telecommunication systems. Original analog methods of telephony had the disadvantage of speech signal getting corrupted by noise, cross-talk and distortion Long haul transmissions which use repeaters to compensate for the loss in signal strength on transmission links also increase the associated noise and distortion. On the other hand digital transmission is relatively immune to noise, cross-talk and distortion primarily because of the capability to faithfully regenerate digital signal at each repeater purely based on a binary decision. Hence end-to-end performance of the digital link essentially becomes independent of the length and operating frequency bands of the link Hence from a transmission point of view digital transmission has been the preferred approach due to its higher immunity to noise. The need to carry digital speech became extremely important from a service provision point of view as well. Modem requirements have introduced the need for robust, flexible and secure services that can carry a multitude of signal types (such as voice, data and video) without a fundamental change in infrastructure. Such a requirement could not have been easily met without the advent of digital transmission systems, thereby requiring speech to be coded digitally. The term Speech Coding is often referred to techniques that represent or code speech signals either directly as a waveform or as a set of parameters by analyzing the speech signal. In either case, the codes are transmitted to the distant end where speech is reconstructed or synthesized using the received set of codes. A more generic term that is applicable to these techniques that is often interchangeably used with speech coding is the term voice coding. This term is more generic in the sense that the

  16. FY08 LDRD Final Report A New Method for Wave Propagation in Elastic Media LDRD Project Tracking Code: 05-ERD-079

    SciTech Connect (OSTI)

    Petersson, A

    2009-01-29

    The LDRD project 'A New Method for Wave Propagation in Elastic Media' developed several improvements to the traditional finite difference technique for seismic wave propagation, including a summation-by-parts discretization which is provably stable for arbitrary heterogeneous materials, an accurate treatment of non-planar topography, local mesh refinement, and stable outflow boundary conditions. This project also implemented these techniques in a parallel open source computer code called WPP, and participated in several seismic modeling efforts to simulate ground motion due to earthquakes in Northern California. This research has been documented in six individual publications which are summarized in this report. Of these publications, four are published refereed journal articles, one is an accepted refereed journal article which has not yet been published, and one is a non-refereed software manual. The report concludes with a discussion of future research directions and exit plan.

  17. Code development incorporating environmental, safety, and economic aspects of fusion reactors (FY 89--91). Final report

    SciTech Connect (OSTI)

    Ho, S.K.; Fowler, T.K.; Holdren, J.P. [eds.

    1991-11-01

    This report discusses the following aspects of Fusion reactors.: Activation Analysis; Tritium Inventory; Environmental and Safety Indices and Their Graphical Representation; Probabilistic Risk Assessment (PRA) and Decision Analysis; Plasma Burn Control -- Application to ITER; and Other Applications.

  18. Compiling Codes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Compiling Codes Compiling Codes Overview Open Mpi is the the only MPI library available on Euclid. This implementation of MPI-2 is described at Open MPI: Open Source High Performance Computing. The default compiler suite is from the Portland Group which is loaded by default at login, along with the PGI compiled Open MPI environment. % module list Currently Loaded Modulefiles: 1) pgi/10.8 2) openmpi/1.4.2 Basic Example Open MPI provides a convenient set of wrapper commands which you should use in

  19. Report on subcontract from Lawrence Livermore National Lab, "Development of Large-Dimension Configuration-Interaction Shell-Model Code"

    SciTech Connect (OSTI)

    Johnson, C W

    2012-01-24

    The project period was devoted to several developments in the technical capabilities of the BIGSTIC large-dimension configuration-interaction shell-model code, written in Fortran 90. The specific computational goals for the project period were: (1) store Lanczos vectors on core in RAM to minimize I/O; (2) rewrite reorthogonalization with Lanczos vectors stored in core, consult with personnel at LLNL, LBL, ORNL, Iowa State University to maximize performance; (3) restrict creation of N-body jumps to those needed by an individual node; and (4) distribute 3-body interaction over many cores. Significant progress was made towards these goals, especially (1) and (2), although in the process they discovered intermediate tasks that had to be accomplished first. The achievements were as follows - I put into place structures and algorithms to facility fragmenting very large-dimension Lanczos intermediate vectors. Only by fragmenting the vectors can we carry out (1) and (2). In addition, I reorganized the action of the Hamiltonian matrix and created a new division of operations for MPI. Based upon earlier work, I made plans of a revised algorithm for distribution of work with MPI, with a particular eye towards breaking up the Lanczos vectors. I introduce a new derived type (opbundles) which collects the parameters for the Hamiltonian, and rewrote the application routines to use it. It has been validated and verified. I made progress towards revised MPI parallelization. Using the opbundles, I was able to compute a distribution of work over compute nodes, which should be very efficient. This new distribution is easier to derive and more efficient, in principle, than the old distribution. Furthermore, it should make applications with fragmented Lanczos vectors easier. Implementation is still in progress.

  20. Development of safety analysis codes and experimental validation for a very high temperature gas-cooled reactor Final report

    SciTech Connect (OSTI)

    Chang Oh

    2006-03-01

    The very high-temperature gas-cooled reactor (VHTR) is envisioned as a single- or dual-purpose reactor for electricity and hydrogen generation. The concept has average coolant temperatures above 9000C and operational fuel temperatures above 12500C. The concept provides the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperature to support process heat applications, such as coal gasification, desalination or cogenerative processes, the VHTR’s higher temperatures allow broader applications, including thermochemical hydrogen production. However, the very high temperatures of this reactor concept can be detrimental to safety if a loss-of-coolant accident (LOCA) occurs. Following the loss of coolant through the break and coolant depressurization, air will enter the core through the break by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structure and fuel. The oxidation will accelerate heatup of the reactor core and the release of toxic gasses (CO and CO2) and fission products. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. Prior to the start of this Korean/United States collaboration, no computer codes were available that had been sufficiently developed and validated to reliably simulate a LOCA in the VHTR. Therefore, we have worked for the past three years on developing and validating advanced computational methods for simulating LOCAs in a VHTR. Research Objectives As described above, a pipe break may lead to significant fuel damage and fission product release in the VHTR. The objectives of this Korean/United States collaboration were to develop and validate advanced computational methods for VHTR safety analysis. The methods that have been developed are now

  1. code release

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    code release - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Energy Defense Waste Management Programs Advanced Nuclear Energy

  2. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Bureau of Construction Codes is responsible for the administration of the State Construction Code Act (1972 PA 230), also known as the Uniform Construction Code.

  3. Building Energy Code

    Broader source: Energy.gov [DOE]

    Georgia's Department of Community Affairs periodically reviews, amends and/or updates the state minimum standard codes. Georgia has "mandatory" and "permissive" codes. Georgia State Energy Code...

  4. Coded credentials: A primer

    SciTech Connect (OSTI)

    Wright, L.J.

    1988-02-01

    The need to identify people is an age-old requirement that has taken many forms over the ages. With the advent of the age of technology, the need has become more acute and many methods have been devised to help with the identification process. This report is designed to be a primer on one of those methods - the coded credential, e.g., a credential that is compatible with computerized access control systems.

  5. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    NOTE: On March 9, 2016, the State Fire Prevention and Building Code Council adopted major updates to the State Uniform Code and the State Energy Code. The State Energy Code has been updated to 2015...

  6. Securing mobile code.

    SciTech Connect (OSTI)

    Link, Hamilton E.; Schroeppel, Richard Crabtree; Neumann, William Douglas; Campbell, Philip LaRoche; Beaver, Cheryl Lynn; Pierson, Lyndon George; Anderson, William Erik

    2004-10-01

    If software is designed so that the software can issue functions that will move that software from one computing platform to another, then the software is said to be 'mobile'. There are two general areas of security problems associated with mobile code. The 'secure host' problem involves protecting the host from malicious mobile code. The 'secure mobile code' problem, on the other hand, involves protecting the code from malicious hosts. This report focuses on the latter problem. We have found three distinct camps of opinions regarding how to secure mobile code. There are those who believe special distributed hardware is necessary, those who believe special distributed software is necessary, and those who believe neither is necessary. We examine all three camps, with a focus on the third. In the distributed software camp we examine some commonly proposed techniques including Java, D'Agents and Flask. For the specialized hardware camp, we propose a cryptographic technique for 'tamper-proofing' code over a large portion of the software/hardware life cycle by careful modification of current architectures. This method culminates by decrypting/authenticating each instruction within a physically protected CPU, thereby protecting against subversion by malicious code. Our main focus is on the camp that believes that neither specialized software nor hardware is necessary. We concentrate on methods of code obfuscation to render an entire program or a data segment on which a program depends incomprehensible. The hope is to prevent or at least slow down reverse engineering efforts and to prevent goal-oriented attacks on the software and execution. The field of obfuscation is still in a state of development with the central problem being the lack of a basis for evaluating the protection schemes. We give a brief introduction to some of the main ideas in the field, followed by an in depth analysis of a technique called 'white-boxing'. We put forth some new attacks and improvements

  7. Tandem Mirror Reactor Systems Code (Version I)

    SciTech Connect (OSTI)

    Reid, R.L.; Finn, P.A.; Gohar, M.Y.; Barrett, R.J.; Gorker, G.E.; Spampinaton, P.T.; Bulmer, R.H.; Dorn, D.W.; Perkins, L.J.; Ghose, S.

    1985-09-01

    A computer code was developed to model a Tandem Mirror Reactor. Ths is the first Tandem Mirror Reactor model to couple, in detail, the highly linked physics, magnetics, and neutronic analysis into a single code. This report describes the code architecture, provides a summary description of the modules comprising the code, and includes an example execution of the Tandem Mirror Reactor Systems Code. Results from this code for two sensitivity studies are also included. These studies are: (1) to determine the impact of center cell plasma radius, length, and ion temperature on reactor cost and performance at constant fusion power; and (2) to determine the impact of reactor power level on cost.

  8. " Row: NAICS Codes; Column: Energy Sources...

    U.S. Energy Information Administration (EIA) Indexed Site

    and",,"Coke"," ","Row" "Code(a)","Subsector and ... 324,"Petroleum and Coal ... Division, Form EIA-810, 'Monthly Refinery Report' for 2002.

  9. " Row: NAICS Codes; Column: Energy Sources...

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Sources","Row" "Code(a)","Subsector and ... 324,"Petroleum and Coal ... Division, Form EIA-810, 'Monthly Refinery Report' for 2002.

  10. FRAPCON-2: a computer code for the calculation of steady state thermal-mechanical behavior of oxide fuel rods. Technical report

    SciTech Connect (OSTI)

    Berna, G.A.; Bohn, M.P.; Rausch, W.N.; Williford, R.E.; Lanning, D.D.

    1981-01-01

    FRAPCON-2 is a FORTRAN IV computer code that calculates the steady state response of light water reactor fuel rods during long-term burnup. The code calculates the temperature, pressure, deformation, and failure histories of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include: (a) heat conduction through the fuel and cladding, (b) cladding elastic and plastic deformation, (c) fuel-cladding mechanical interaction, (d) fission gas release, (e) fuel rod internal gas pressure, (f) heat transfer between fuel and cladding, (g) cladding oxidation, and (h) heat transfer from cladding to coolant. The code contains necessary material properties, water properties, and heat transfer correlations. FRAPCON-2 is programmed for use on the CDC Cyber 175 and 176 computers. The FRAPCON-2 code is designed to generate initial conditions for transient fuel rod analysis by either the FRAP-T6 computer code or the thermal-hydraulic code, RELAP4/MOD7 Version2.

  11. CENER/NREL Collaboration in Testing Facility and Code Development: Cooperative Research and Development Final Report, CRADA Number CRD-06-207

    SciTech Connect (OSTI)

    Moriarty, P.

    2014-11-01

    Under the funds-in CRADA agreement, NREL and CENER will collaborate in the areas of blade and drivetrain testing facility development and code development. The project shall include NREL assisting in the review and instruction necessary to assist in commissioning the new CENER blade test and drivetrain test facilities. In addition, training will be provided by allowing CENER testing staff to observe testing and operating procedures at the NREL blade test and drivetrain test facilities. CENER and NREL will exchange blade and drivetrain facility and equipment design and performance information. The project shall also include exchanging expertise in code development and data to validate numerous computational codes.

  12. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    Mississippi's existing state code is based on the 1977 Model Code for Energy Conservation (MCEC). The existing law does not mandate enforcement by localities, and any revised code will probably...

  13. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    The State Building Code Council revised the Washington State Energy Code (WESC) in February 2013, effective July 1, 2013. The WESC is a state-developed code based upon ASHRAE 90.1-2010 and the...

  14. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Kentucky Building Code (KBC) is updated every three years on a cycle one year behind the publication year for the International Building Code. Any changes to the code by the state of Kentucky...

  15. 11. CONTRACT ID CODE

    National Nuclear Security Administration (NNSA)

    79120 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) Babcock & Wilcox Technical Services Pantex, LLC PO Box 30020 Amarillo, TX 79120 CODE I FACILITY ...

  16. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Rhode Island Building Code Standards Committee adopts, promulgates and administers the state building code. Compliance is determined through the building permit and inspection process by local...

  17. Building Energy Code

    Broader source: Energy.gov [DOE]

    The North Carolina State Building Code Council is responsible for developing all state codes. By statute, the Commissioner of Insurance has general supervision over the administration and...

  18. Building Energy Code

    Broader source: Energy.gov [DOE]

    The West Virginia State Fire Commission is responsible for adopting and promulgating statewide construction codes. These codes may be voluntarily adopted at the local level. Local jurisdictions...

  19. Building Energy Code

    Broader source: Energy.gov [DOE]

    Public Act 093-0936 (Illinois Energy Conservation Code for Commercial Buildings) was signed into law in August, 2004. The Illinois Energy Conservation Code for Commercial Buildings became...

  20. Building Energy Codes: State and Local Code Implementation Overview

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mark Lessans Fellow Building Energy Codes: State and Local Code Implementation Overview ... building code regarding energy efficiency to the revised model code and submit a ...

  1. New Code Compliance Briefs Assist in Resolving Codes and Standards...

    Energy Savers [EERE]

    New Code Compliance Briefs Assist in Resolving Codes and Standards Concerns in Energy Innovations New Code Compliance Briefs Assist in Resolving Codes and Standards Concerns in ...

  2. Development of Safety Analysis Codes and Experimental Validation for a Very High Temperature Gas-Cooled Reactor - FY-05 Annual Report

    SciTech Connect (OSTI)

    Chang Oh

    2005-09-01

    The very high temperature gas-cooled reactors (VHTGRs) are those concepts that have average coolant temperatures above 9000C or operational fuel temperatures above 12500C. These concepts provide the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation and nuclear hydrogen generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperatures to support process heat applications, such as desalination and cogeneration, the VHTGR’s higher temperatures are suitable for particular applications such as thermochemical hydrogen production. However, the high temperature operation can be detrimental to safety following a loss-of-coolant accident (LOCA) initiated by pipe breaks caused by seismic or other events. Following the loss of coolant through the break and coolant depressurization, air from the containment will enter the core by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structures and fuel. The oxidation will release heat and accelerate the heatup of the reactor core. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. The Idaho National Laboratory (INL) has investigated this event for the past three years for the HTGR. However, the computer codes used, and in fact none of the world’s computer codes, have been sufficiently developed and validated to reliably predict this event. New code development, improvement of the existing codes, and experimental validation are imperative to narrow the uncertainty in the predictions of this type of accident. The objectives of this Korean/United States collaboration are to develop advanced computational methods for VHTGR safety analysis codes and to validate these computer codes.

  3. Steady-State Gyrokinetics Transport Code (SSGKT), A Scientific Application Partnership with the Framework Application for Core-Edge Transport Simulations, Final Report

    SciTech Connect (OSTI)

    Fahey, Mark R.; Candy, Jeff

    2013-11-07

    This project initiated the development of TGYRO ? a steady-state Gyrokinetic transport code (SSGKT) that integrates micro-scale GYRO turbulence simulations into a framework for practical multi-scale simulation of conventional tokamaks as well as future reactors. Using a lightweight master transport code, multiple independent (each massively parallel) gyrokinetic simulations are coordinated. The capability to evolve profiles using the TGLF model was also added to TGYRO and represents a more typical use-case for TGYRO. The goal of the project was to develop a steady-state Gyrokinetic transport code (SSGKT) that integrates micro-scale gyrokinetic turbulence simulations into a framework for practical multi-scale simulation of a burning plasma core ? the International Thermonuclear Experimental Reactor (ITER) in particular. This multi-scale simulation capability will be used to predict the performance (the fusion energy gain, Q) given the H-mode pedestal temperature and density. At present, projections of this type rely on transport models like GLF23, which are based on rather approximate fits to the results of linear and nonlinear simulations. Our goal is to make these performance projections with precise nonlinear gyrokinetic simulations. The method of approach is to use a lightweight master transport code to coordinate multiple independent (each massively parallel) gyrokinetic simulations using the GYRO code. This project targets the practical multi-scale simulation of a reactor core plasma in order to predict the core temperature and density profiles given the H-mode pedestal temperature and density. A master transport code will provide feedback to O(16) independent gyrokinetic simulations (each massively parallel). A successful feedback scheme offers a novel approach to predictive modeling of an important national and international problem. Success in this area of fusion simulations will allow US scientists to direct the research path of ITER over the next two

  4. RELAP5/MOD3 code manual

    SciTech Connect (OSTI)

    Sloan, S.M.; Schultz, R.R.; Wilson, G.E.

    1994-06-01

    Summaries of RELAP5/MOD3 code assessments, a listing of the assessment matrix, and a chronology of the various versions of the code are given. Results from these code assessments have been used to formulate a compilation of some of the strengths and weaknesses of the code. These results are documented in the report. Volume 7 was designed to be updated periodically and to include the results of the latest code assessments as they become available. Consequently, users of Volume 7 should ensure that the latest revision is available.

  5. Manually operated coded switch

    DOE Patents [OSTI]

    Barnette, Jon H.

    1978-01-01

    The disclosure relates to a manually operated recodable coded switch in which a code may be inserted, tried and used to actuate a lever controlling an external device. After attempting a code, the switch's code wheels must be returned to their zero positions before another try is made.

  6. Using an automated code management system to improve configuration control practices

    SciTech Connect (OSTI)

    Meyer, S.

    1997-11-01

    This report contains viewgraphs on using an automated code management system to improve configuration control practice.

  7. Group representations, error bases and quantum codes

    SciTech Connect (OSTI)

    Knill, E

    1996-01-01

    This report continues the discussion of unitary error bases and quantum codes. Nice error bases are characterized in terms of the existence of certain characters in a group. A general construction for error bases which are non-abelian over the center is given. The method for obtaining codes due to Calderbank et al. is generalized and expressed purely in representation theoretic terms. The significance of the inertia subgroup both for constructing codes and obtaining the set of transversally implementable operations is demonstrated.

  8. The CZTU uranium concentration analysis code

    SciTech Connect (OSTI)

    Clark, D., LLNL

    1998-07-17

    A {sup 235}U analysis code, CZTU, has been written that can non- destructively evaluate the percentage of {sup 235}U in a uranium sample from the analysis of the emitted gamma rays. This code utilizes gamma spectra measured from room temperature Cadmium Zinc Telluride (CdZnTe or CZT) detectors. It has an accuracy midway between that obtained with sodium iodide and germanium crystal detectors. This report describes how to use the code, some results, limitations and design considerations.

  9. Continuous Intercomparison of Radiation Codes (CIRC)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Intercomparison of Radiation Codes (CIRC) * Sponsored by ARM and endorsed by GEWEX Radiation Panel * Aims to become the standard for documenting the performance of SW and LW RT codes in Large-Scale Models * Goal is to have RT codes of IPCC models report performance against the CIRC cases * Phase I to be launched in the following weeks: http://www.circ-project.org Differences from previous intercomparisons: * Observation-tested LBL calculations to used as radiative benchmarks * Benchmark results

  10. Building Energy Code

    Broader source: Energy.gov [DOE]

    New Hampshire adopted a mandatory statewide building code in 2002 based on the 2000 IECC. S.B. 81 was enacted in July 2007, and it upgraded the New Hampshire Energy Code to the 2006 IECC. In Dece...

  11. Building Energy Code

    Broader source: Energy.gov [DOE]

    Note: Much of the information presented in this summary is drawn from the U.S. Department of Energys (DOE) Building Energy Codes Program and the Building Codes Assistance Project (BCAP). For more...

  12. Building Energy Code

    Broader source: Energy.gov [DOE]

    The New Jersey Uniform Construction Code Act provides that model codes and standards publications shall not be adopted more frequently than once every three years. However, a revision or amendment...

  13. Building Energy Code

    Broader source: Energy.gov [DOE]

    Legislation passed in March 2010 authorized the Alabama Energy and Residential Code (AERC) Board to adopt mandatory residential and commercial energy codes for all jurisdictions. In 2015, the AER...

  14. Building Energy Code

    Broader source: Energy.gov [DOE]

    A mandatory energy code is not enforced at the state level. If a local energy code is adopted, it is enforced at the local level. Builders or sellers of new residential buildings (single-family or...

  15. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    Note: Much of the information presented in this summary is drawn from the U.S. Department of Energy’s (DOE) Building Energy Codes Program and the Building Codes Assistance Project (BCAP). For more...

  16. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Indiana Residential Building Code is based on the 2003 IRC with state amendments (eff. 9/11/05). This code applies to 1 and 2 family dwellings and townhouses. During the adoption process,...

  17. Building Energy Code

    Broader source: Energy.gov [DOE]

    The 1993 State Legislature updated the state energy code to the 1989 Model Energy Code (MEC) and established a procedure to update the standard. Then in 1995, following consultation with an...

  18. Building Energy Code

    Broader source: Energy.gov [DOE]

    Prior to 1997, South Carolina's local governments adopted and enforced the building codes. In 1997, the law required statewide use of the most up-to-date building codes, which then required the...

  19. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Florida Building Commission (FBC) is directed to adopt, revise, update, and maintain the Florida Building Code in accordance with Chapter 120 of the state statutes. The code is mandatory...

  20. Building Energy Code

    Broader source: Energy.gov [DOE]

    In 2006 Iowa enacted H.F. 2361, requiring the State Building Commissioner to adopt energy conservation requirements based on a nationally recognized building energy code. The State Building Code...

  1. Building Energy Code

    Broader source: Energy.gov [DOE]

    In September 2011 the Nebraska Building Energy Code was updated to the 2009 International Energy Conservation Code (IECC) standards. As with the previous 2003 IECC standards, which had been in...

  2. Building Energy Code

    Broader source: Energy.gov [DOE]

    In November of 2015, the Commission adopted the 2015 International Building Code (IBC) with amendments. The Commission did not adopt the 2012 International Energy Conservation Code (IECC) as part...

  3. Building Energy Code

    Broader source: Energy.gov [DOE]

    Much of the information presented in this summary is drawn from the U.S. Department of Energy’s (DOE) Building Energy Codes Program and the Building Codes Assistance Project (BCAP). For more deta...

  4. Building Energy Code

    Broader source: Energy.gov [DOE]

    Changes to the energy code are submitted to the Uniform Building Code Commission. The proposed change is reviewed by the Commission at a monthly meeting to decide if it warrants further considera...

  5. Building Energy Code

    Broader source: Energy.gov [DOE]

    Much of the information presented in this summary is drawn from the U.S. Department of Energy’s (DOE) Building Energy Codes Program and the Building Codes Assistance Project (BCAP). For more...

  6. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Virginia Uniform Statewide Building Code (USBC) is a statewide minimum requirement that local jurisdictions cannot amend. The code is applicable to all new buildings in the commonwealth. The...

  7. Guam- Building Energy Code

    Broader source: Energy.gov [DOE]

    Much of the information presented in this summary is drawn from the U.S. Department of Energy’s (DOE) Building Energy Codes Program and the Building Codes Assistance Project (BCAP). For more...

  8. Building Energy Code

    Broader source: Energy.gov [DOE]

    Colorado is a home rule state, so no statewide energy code exists, although state government buildings do have specific requirements. Voluntary adoption of energy codes is encouraged and efforts...

  9. Building Energy Code

    Broader source: Energy.gov [DOE]

    All residential and commercial structures are required to comply with the state’s energy code. The 2009 New Mexico Energy Conservation Code (NMECC), effective June 2013, is based on 2009...

  10. Building Energy Code

    Broader source: Energy.gov [DOE]

    The 2012 IECC is in effect for all residential and commercial buildings, Idaho schools, and Idaho jurisdictions that adopt and enforce building codes, unless a local code exists that is more...

  11. Cellulases and coding sequences

    DOE Patents [OSTI]

    Li, Xin-Liang; Ljungdahl, Lars G.; Chen, Huizhong

    2001-01-01

    The present invention provides three fungal cellulases, their coding sequences, recombinant DNA molecules comprising the cellulase coding sequences, recombinant host cells and methods for producing same. The present cellulases are from Orpinomyces PC-2.

  12. Cellulases and coding sequences

    DOE Patents [OSTI]

    Li, Xin-Liang; Ljungdahl, Lars G.; Chen, Huizhong

    2001-02-20

    The present invention provides three fungal cellulases, their coding sequences, recombinant DNA molecules comprising the cellulase coding sequences, recombinant host cells and methods for producing same. The present cellulases are from Orpinomyces PC-2.

  13. To develop a dynamic model of a collector loop for purpose of improved control of solar heating and cooling. Final technical report. [TRNSYS code

    SciTech Connect (OSTI)

    Herczfeld, P R; Fischl, R

    1980-01-01

    The program objectives were to (1) assess the feasibility of using the TRNSYS computer code for solar heating and cooling control studies and modify it wherever possible, and (2) develop a new dynamic model of the solar collector which reflects the performance of the collector under transient conditions. Also, the sensitivity of the performance of this model to the various system parameters such as collector time constants, flow rates, turn-on and turn-off temperature set points, solar insolation, etc., was studied. Results are presented and discussed. (WHK)

  14. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    In March 2006, SB 459 was enacted to promote renewable energy and update the state's building energy codes.

  15. ASME Code Efforts Supporting HTGRs

    SciTech Connect (OSTI)

    D.K. Morton

    2012-09-01

    In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

  16. ASME Code Efforts Supporting HTGRs

    SciTech Connect (OSTI)

    D.K. Morton

    2011-09-01

    In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

  17. ASME Code Efforts Supporting HTGRs

    SciTech Connect (OSTI)

    D.K. Morton

    2010-09-01

    In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

  18. Probability of pipe fracture in the primary coolant loop of a PWR plant. Volume 9. PRAISE computer code user's manual. Load Combination Program Project I final report

    SciTech Connect (OSTI)

    Lim, E.Y.

    1981-06-01

    The PRAISE (Piping Reliability Analysis Including Seismic Events) computer code estimates the influence of earthquakes on the probability of failure at a weld joint in the primary coolant system of a pressurized water reactor. Failure, either a through-wall defect (leak) or a complete pipe severance (a large-LOCA), is assumed to be caused by fatigue crack growth of an as-fabricated interior surface circumferential defect. These defects are assumed to be two-dimensional and semi-elliptical in shape. The distribution of initial crack sizes is a function of crack depth and aspect ratio. PRAISE treats the inter-arrival times of operating transients either as a constant or exponentially distributed according to observed or postulated rates. Leak rate and leak detection models are also included. The criterion for complete pipe severance is exceedance of a net section critical stress. Earthquakes of various intensity and arbitrary occurrence times can be modeled. PRAISE presently assumes that exactly one initial defect exists in the weld and that the earthquake of interest is the first earthquake experienced at the reactor. PRAISE has a very modular structure and can be tailored to a variety of crack growth and piping reliability problems. Although PRAISE was developed on a CDC-7600 computer, it was, however, coded in standard FORTRAN IV and is readily transportable to other machines.

  19. TRAC Code Modifications Made for APT Blanket Safety Analyses

    SciTech Connect (OSTI)

    Hamm, L.L.

    1998-10-07

    This report provides documentation of the necessary source code modifications made to the TRAC-PF1/MOD2 code version 5.4.28a developed at Los Alamos National Laboratory.

  20. Stationary Fuel Cell Application Codes and Standards: Overview and Gap Analysis

    SciTech Connect (OSTI)

    Blake, C. W.; Rivkin, C. H.

    2010-09-01

    This report provides an overview of codes and standards related to stationary fuel cell applications and identifies gaps and resolutions associated with relative codes and standards.

  1. DLLExternalCode

    Energy Science and Technology Software Center (OSTI)

    2014-05-14

    DLLExternalCode is the a general dynamic-link library (DLL) interface for linking GoldSim (www.goldsim.com) with external codes. The overall concept is to use GoldSim as top level modeling software with interfaces to external codes for specific calculations. The DLLExternalCode DLL that performs the linking function is designed to take a list of code inputs from GoldSim, create an input file for the external application, run the external code, and return a list of outputs, read frommore » files created by the external application, back to GoldSim. Instructions for creating the input file, running the external code, and reading the output are contained in an instructions file that is read and interpreted by the DLL.« less

  2. DLLExternalCode

    SciTech Connect (OSTI)

    Greg Flach, Frank Smith

    2014-05-14

    DLLExternalCode is the a general dynamic-link library (DLL) interface for linking GoldSim (www.goldsim.com) with external codes. The overall concept is to use GoldSim as top level modeling software with interfaces to external codes for specific calculations. The DLLExternalCode DLL that performs the linking function is designed to take a list of code inputs from GoldSim, create an input file for the external application, run the external code, and return a list of outputs, read from files created by the external application, back to GoldSim. Instructions for creating the input file, running the external code, and reading the output are contained in an instructions file that is read and interpreted by the DLL.

  3. Development of rotating shadowband spectral radiometers and GCM radiation code test data sets in support of ARM. Technical progress report, September 15, 1990--September 14, 1991

    SciTech Connect (OSTI)

    Harrison, L.; Michalsky, J.

    1991-03-13

    Three separate tasks are included in the first year of the project. Two involve assembling data sets useful for testing radiation models in global climate modeling (GCM) codes, and the third is concerned with the development of advance instrumentation for performing accurate spectral radiation measurements. Task 1: Three existing data sets have been merged for two locations, one in the wet northeastern US and a second in the dry western US. The data sets are meteorological data from the WBAN network, upper air data from the NCDC, and high quality solar radiation measurements from Albany, New York and Golden, Colorado. These represent test data sets for those modelers developing radiation codes for the GCM models. Task 2: Existing data are not quite adequate from a modeler`s perspective without downwelling infrared data and surface albedo, or reflectance, data. Before the deployment of the first CART site in ARM the authors are establishing this more complete set of radiation measurements at the Albany site to be operational only until CART is operational. The authors will have the site running by April 1991, which will provide about one year`s data from this location. They will coordinate their measurements with satellite overpasses, and, to the extent possible, with radiosonde releases, in order that the data set be coincident in time. Task 3: Work has concentrated on the multiple filter instrument. The mechanical, optical, and software engineering for this instrument is complete, and the first field prototype is running at the Rattlesnake Mountain Observatory (RMO) test site. This instrument is performing well, and is already delivering reliable and useful information.

  4. Generating code adapted for interlinking legacy scalar code and extended vector code

    DOE Patents [OSTI]

    Gschwind, Michael K

    2013-06-04

    Mechanisms for intermixing code are provided. Source code is received for compilation using an extended Application Binary Interface (ABI) that extends a legacy ABI and uses a different register configuration than the legacy ABI. First compiled code is generated based on the source code, the first compiled code comprising code for accommodating the difference in register configurations used by the extended ABI and the legacy ABI. The first compiled code and second compiled code are intermixed to generate intermixed code, the second compiled code being compiled code that uses the legacy ABI. The intermixed code comprises at least one call instruction that is one of a call from the first compiled code to the second compiled code or a call from the second compiled code to the first compiled code. The code for accommodating the difference in register configurations is associated with the at least one call instruction.

  5. Mechanical code comparator

    DOE Patents [OSTI]

    Peter, Frank J.; Dalton, Larry J.; Plummer, David W.

    2002-01-01

    A new class of mechanical code comparators is described which have broad potential for application in safety, surety, and security applications. These devices can be implemented as micro-scale electromechanical systems that isolate a secure or otherwise controlled device until an access code is entered. This access code is converted into a series of mechanical inputs to the mechanical code comparator, which compares the access code to a pre-input combination, entered previously into the mechanical code comparator by an operator at the system security control point. These devices provide extremely high levels of robust security. Being totally mechanical in operation, an access control system properly based on such devices cannot be circumvented by software attack alone.

  6. Compiling Codes on Hopper

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Compiling Codes Compiling Codes on Hopper Overview Cray provides a convenient set of wrapper commands that should be used in almost all cases for compiling and linking parallel programs. Invoking the wrappers will automatically link codes with MPI libraries and other Cray system software. All MPI and Cray system include directories are also transparently imported. In addition the wrappers append the compiler's target processor arguments for the hopper compute node processors. NOTE: The intention

  7. Code of Conduct

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Governance » Ethics, Accountability, Contract » Code of Conduct Code of Conduct Helping employees recognize and resolve the ethics and compliance issues that may arise in their daily work. Contact Ethics and Compliance Group (505) 667-7506 Email Code of Conduct Los Alamos National Laboratory is committed to operating in accordance with the highest standards of ethics and compliance and with its core values of service to our nation, ethical conduct and personal accountability, excellence in our

  8. Shields - Code Coupling

    SciTech Connect (OSTI)

    Vernon, Louis James

    2015-03-02

    This PowerPoint presentation focuses on the history and benefits of the Space Weather Modeling Framework (SWMF) code and collaborative software development.

  9. Tokamak Systems Code

    SciTech Connect (OSTI)

    Reid, R.L.; Barrett, R.J.; Brown, T.G.; Gorker, G.E.; Hooper, R.J.; Kalsi, S.S.; Metzler, D.H.; Peng, Y.K.M.; Roth, K.E.; Spampinato, P.T.

    1985-03-01

    The FEDC Tokamak Systems Code calculates tokamak performance, cost, and configuration as a function of plasma engineering parameters. This version of the code models experimental tokamaks. It does not currently consider tokamak configurations that generate electrical power or incorporate breeding blankets. The code has a modular (or subroutine) structure to allow independent modeling for each major tokamak component or system. A primary benefit of modularization is that a component module may be updated without disturbing the remainder of the systems code as long as the imput to or output from the module remains unchanged.

  10. Building Energy Codes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    David Cohan Program Manager Building Energy Codes April 22, 2014 Presentation Outline * Mission * Goals * Program Organization * StrategiesRoles * Near-Term Focus * Measuring ...

  11. Improving Code Compliance

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    provisions in International Energy Conservation Code (IECC) through proof-of-concept ... This includes updating recommendations based on newer CBECs or BPD energy statistics. ...

  12. Top NAICS Codes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Related Products Manufacturing for Measuring, Displaying, Top Ten NAICS Codes Dollar Value 511210 Software Publishers 334516 Analytical Laboratory Instrument Manufacturing...

  13. Building Energy Code

    Broader source: Energy.gov [DOE]

    Kansas adopted the 2006 International Energy Conservation Code (IECC) as "the applicable state standard" for commercial and industrial buildings. Enforcement is provided by local jurisdictions; t...

  14. Building Energy Code

    Broader source: Energy.gov [DOE]

    Pennsylvania Department of Labor and Industry (DLI) has the authority to upgrade commercial and residential energy standards through the regulatory process. The current code, the 2009 UCC, became...

  15. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Maryland Building Performance Standards (MBPS) are adopted by the Maryland Department of Housing and Community Development (DHCD) Codes Administration. As required by legislation passed in...

  16. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Connecticut Office of the State Building Inspector establishes and enforces building, electrical, mechanical, plumbing and energy code requirements by reviewing, developing, adopting and...

  17. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Office of the State Fire Marshal is granted the authority to promulgate amendments, revisions, and alternative compliance methods for the code.

  18. Probability of pipe fracture in the primary coolant loop of a PWR plant. Volume 9: PRAISE computer code user's manual. Final report

    SciTech Connect (OSTI)

    Lim, E.Y.

    1981-08-01

    The PRAISE (Piping Reliability Analysis Including Seismic Events) computer code estimates the influence of earthquakes on the probability of failure at a weld joint in the primary coolant system of a pressurized water reactor. Failure, either a through-wall defect (leak) or a complete pipe severance (a large-LOCA), is assumed to be caused by fatigue crack growth of an as-fabricated interior surface circumferential defect. These defects are assumed to be two-dimensional and semi-elliptical in shape. The distribution of initial crack sizes is a function of crack depth and aspect ratio. Crack propagation rates are governed by a Paris-type relationship with separate RMS cyclic stress intensity factors for the depth and length. Both uniform through the wall and radial gradient thermal stresses are included in the calculation of the stress intensity factors. The failure probabilities are estimated by applying Monte Carlo methods to simulate the life histories of the selected weld joint. In order to maximize computational efficiency, a stratified sampling procedure is used to select the initial crack size. Hydrostatic proof test, pre-service inspection, and in-service inspection can be simulated. PRAISE treats the inter-arrival times of operating transients either as a constant or exponentially distributed according to observed or postulated rates. Leak rate and leak detection models are also included. The criterion for complete pipe severance is exceedance of a net section critical stress. Earthquakes of various intensity and arbitrary occurrence times can be modeled. PRAISE presently assumes that exactly one initial defect exists in the weld and that the earthquake of interest is the first earthquake experienced at the reactor.

  19. FLOWTRAN-TF v1.2 source code

    SciTech Connect (OSTI)

    Aleman, S.E.; Cooper, R.E.; Flach, G.P.; Hamm, L.L.; Lee, S.; Smith, F.G. III

    1993-02-01

    The FLOWTRAN-TF code development effort was initiated in early 1989 as a code to monitor production reactor cooling systems at the Savannah River Plant. This report is a documentation of the various codes that make up FLOWTRAN-TF.

  20. FLOWTRAN-TF v1. 2 source code

    SciTech Connect (OSTI)

    Aleman, S.E.; Cooper, R.E.; Flach, G.P.; Hamm, L.L.; Lee, S.; Smith, F.G. III.

    1993-02-01

    The FLOWTRAN-TF code development effort was initiated in early 1989 as a code to monitor production reactor cooling systems at the Savannah River Plant. This report is a documentation of the various codes that make up FLOWTRAN-TF.

  1. Building Energy Codes Program

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Program U.S. Department of Energy Building Technologies Office Jeremy Williams, Project Manager Building Technologies Peer Review April 2014 Presentation Overview: * Introduction * Statutory Requirements * Program Structure * Recent accomplishments 2 Introduction: Background NATIONAL STATE LOCAL Building codes are developed through national industry consensus processes with input from industry representatives, trade organizations, government officials, and the general public Model energy codes

  2. Lichenase and coding sequences

    DOE Patents [OSTI]

    Li, Xin-Liang; Ljungdahl, Lars G.; Chen, Huizhong

    2000-08-15

    The present invention provides a fungal lichenase, i.e., an endo-1,3-1,4-.beta.-D-glucanohydrolase, its coding sequence, recombinant DNA molecules comprising the lichenase coding sequences, recombinant host cells and methods for producing same. The present lichenase is from Orpinomyces PC-2.

  3. High Temperature Gas Reactors: Assessment of Applicable Codes...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: High Temperature Gas Reactors: Assessment of Applicable Codes and Standards Citation Details In-Document Search Title: High Temperature Gas Reactors: Assessment ...

  4. High Temperature Gas Reactors: Assessment of Applicable Codes...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: High Temperature Gas Reactors: Assessment of Applicable Codes and ... applicable to HTGR plants, the operating history of past and present HTGR plants, and with ...

  5. A Retrospective Analysis of Commercial Building Energy Codes: 1990 2008

    SciTech Connect (OSTI)

    Belzer, David B.; McDonald, Sean C.; Halverson, Mark A.

    2010-10-01

    Building Energy Codes Program's efforts are designed to result in increased stringency in national model energy codes, more rapid and broader adoption by states and localities of updated codes, and increased compliance and enforcement. Report estimates the historical impact of Building Energy Codes Program in terms of energy savings achieved that are based upon various editions of ANSI/ASHRAE/IESNA Standard 90.1 (ASHRAE Standard 90.1).

  6. In-facility transport code review

    SciTech Connect (OSTI)

    Spore, J.W.; Boyack, B.E.; Bohl, W.R.

    1996-07-01

    The following computer codes were reviewed by the In-Facility Transport Working Group for application to the in-facility transport of radioactive aerosols, flammable gases, and/or toxic gases: (1) CONTAIN, (2) FIRAC, (3) GASFLOW, (4) KBERT, and (5) MELCOR. Based on the review criteria as described in this report and the versions of each code available at the time of the review, MELCOR is the best code for the analysis of in-facility transport when multidimensional effects are not significant. When multi-dimensional effects are significant, GASFLOW should be used.

  7. Compiling Codes on Hopper

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    example.x example.c For C++ source code use CC % CC -fast -o example.x example.C All compilers on Hopper, PGI, Pathscale, Cray, GNU, and Intel, are provided via five programming...

  8. Compressible Astrophysics Simulation Code

    Energy Science and Technology Software Center (OSTI)

    2007-07-18

    This is an astrophysics simulation code involving a radiation diffusion module developed at LLNL coupled to compressible hydrodynamics and adaptive mesh infrastructure developed at LBNL. One intended application is to neutrino diffusion in core collapse supernovae.

  9. Building Energy Code

    Office of Energy Efficiency and Renewable Energy (EERE)

    On May 2014, Delaware updated its energy code to 2012 IECC with amendments for residential sector and ASHRAE 90.1-2010 with amendments for the commercial sector. The Delaware specific amendments to...

  10. Building Energy Code

    Broader source: Energy.gov [DOE]

    Authority for adopting the state energy codes was previously vested in the Energy Security Office of the Department of Commerce (originally the Department of Public Services). In 1999-2000, the...

  11. National Energy Codes Conference

    Broader source: Energy.gov [DOE]

    Join us in Nashville, TN March 23-26, 2015 for the National Energy Codes Conference! Additional details, including registration information, a preliminary agenda, the application for the Jeffrey A...

  12. Compiling Codes on Cori

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    wrappers will automatically link codes with MPI libraries and other Cray system software. ... NOTE: The intention is that programs are compiled on the login nodes and executed on the ...

  13. Compiling Codes on Hopper

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    wrappers will automatically link codes with MPI libraries and other Cray system software. ... NOTE: The intention is that programs are compiled on the login nodes and executed on the ...

  14. Tribal Green Building Codes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    with even amount of white space between photos and header Tribal Green Building Codes Chelsea Chee November 1 3, 2012 SAND 2012---9858C Photos placed in horizontal position with ...

  15. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Massachusetts Board of Building Regulations and Standards has authority to promulgate the Massachusetts State Building Code (MSBC). The energy provisions in the MSBC were developed by the Boa...

  16. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Oregon Energy Code amendments were most recently updated for both residential and non-residential construction in 2014. In October 2010 Oregon also adopted the Oregon Solar Installation...

  17. Building Energy Code

    Broader source: Energy.gov [DOE]

    Both State building codes adoption and enforcement efforts fall under the purview of the State Fire Marshal’s Office within the Department of Commerce and Insurance (C&I). Any changes to the...

  18. Building Energy Code

    Broader source: Energy.gov [DOE]

    The Texas State Energy Conservation Office (SECO) by rule may choose to adopt the latest published editions of the energy efficiency provisions of the International Residential Code (IRC) or the...

  19. Building Energy Code

    Broader source: Energy.gov [DOE]

    Missouri does not have a statewide building or energy code for private residential and commercial buildings, and there currently is no state regulatory agency authorized to promulgate, adopt, or...

  20. PNNL Energy Codes Portfolio

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PNNL Energy Codes Portfolio 2015 Building Technologies Office Peer Review ADOPT COMPLY DEVELOP Bing Liu bing.liu@pnnl.gov Rosemarie Bartlett rosemarie.bartlett@pnnl.gov Pacific Northwest National Laboratory Project Summary Timeline: Multi-year program in support of DOE statutory requirements Key Milestones: 1. DOE's Determinations on 90.1-2013 and 2015 IECC 2. Update DOE's Energy odes ost-Effectiveness Methodology 3. Commercial Codes Roadmap 4. 90.1-2013 and 2015 IECC Cost Analyses 5.

  1. Generating code adapted for interlinking legacy scalar code and...

    Office of Scientific and Technical Information (OSTI)

    Mechanisms for intermixing code are provided. Source code is received for compilation using an extended Application Binary Interface (ABI) that extends a legacy ABI and uses a ...

  2. New Code Compliance Briefs Assist in Resolving Codes and Standards...

    Energy Savers [EERE]

    New Code Compliance Briefs Assist in Resolving Codes and Standards Concerns in Energy ... system knowledge that may limit effective implementation of new and existing standards. ...

  3. Nevada Energy Code for Buildings

    Office of Energy Efficiency and Renewable Energy (EERE)

    Legislation signed in 2009 changed the process of adopting building codes in the state. Previously, the statewide code would only apply to local governments that had not already adopted a code,...

  4. The Application Programming Interface for the PVMEXEC Program and Associated Code Coupling System

    SciTech Connect (OSTI)

    Walter L. Weaver III

    2005-03-01

    This report describes the Application Programming Interface for the PVMEXEC program and the code coupling systems that it implements. The information in the report is intended for programmers wanting to add a new code into the coupling system.

  5. Guide to NRC reporting and recordkeeping requirements. Compiled from requirements in Title 10 of the U.S. Code of Federal Regulations as codified on December 31, 1993; Revision 1

    SciTech Connect (OSTI)

    Collins, M.; Shelton, B.

    1994-07-01

    This compilation includes in the first two sections the reporting and recordkeeping requirements applicable to US Nuclear Regulatory Commission (NRC) licensees and applicants and to members of the public. It includes those requirements codified in Title 10 of the code of Federal Regulations, Chapter 1, on December 31, 1993. It also includes, in a separate section, any of those requirements that were superseded or discontinued between January 1992 and December 1993. Finally, the appendix lists mailing and delivery addresses for NRC Headquarters and Regional Offices mentioned in the compilation. The Office of Information Resources Management staff compiled this listing of reporting and recordkeeping requirements to briefly describe each in a single document primarily to help licensees readily identify the requirements. The compilation is not a substitute for the regulations, and is not intended to impose any new requirements or technical positions. It is part of NRC`s continuing efforts to comply with the Paperwork Reduction Act of 1980 and the Office of Management and Budget regulations that mandate effective and efficient Federal information resources management programs.

  6. Compliance Verification Paths for Residential and Commercial Energy Codes

    SciTech Connect (OSTI)

    Conover, David R.; Makela, Eric J.; Fannin, Jerica D.; Sullivan, Robin S.

    2011-10-10

    This report looks at different ways to verify energy code compliance and to ensure that the energy efficiency goals of an adopted document are achieved. Conformity assessment is the body of work that ensures compliance, including activities that can ensure residential and commercial buildings satisfy energy codes and standards. This report identifies and discusses conformity-assessment activities and provides guidance for conducting assessments.

  7. U-208: HP Operations Agent Bugs Let Remote Users Execute Arbitrary Code

    Broader source: Energy.gov [DOE]

    Two vulnerabilities were reported in HP Operations Agent. A remote user can execute arbitrary code on the target system

  8. U-069: Telnet code execution vulnerability: FreeBSD and Kerberos

    Broader source: Energy.gov [DOE]

    Vulnerability was reported in FreeBSD Telnet. A remote user can execute arbitrary code on the target system.

  9. U-161: Citrix Provisioning Services Unspecified Flaw Lets Remote Users Execute Arbitrary Code

    Broader source: Energy.gov [DOE]

    A vulnerability was reported in Citrix Provisioning Services. A remote user can execute arbitrary code on the target system.

  10. FAA Smoke Transport Code

    Energy Science and Technology Software Center (OSTI)

    2006-10-27

    FAA Smoke Transport Code, a physics-based Computational Fluid Dynamics tool, which couples heat, mass, and momentum transfer, has been developed to provide information on smoke transport in cargo compartments with various geometries and flight conditions. The software package contains a graphical user interface for specification of geometry and boundary conditions, analysis module for solving the governing equations, and a post-processing tool. The current code was produced by making substantial improvements and additions to a codemore » obtained from a university. The original code was able to compute steady, uniform, isothermal turbulent pressurization. In addition, a preprocessor and postprocessor were added to arrive at the current software package.« less

  11. Electrical Circuit Simulation Code

    Energy Science and Technology Software Center (OSTI)

    2001-08-09

    Massively-Parallel Electrical Circuit Simulation Code. CHILESPICE is a massively-arallel distributed-memory electrical circuit simulation tool that contains many enhanced radiation, time-based, and thermal features and models. Large scale electronic circuit simulation. Shared memory, parallel processing, enhance convergence. Sandia specific device models.

  12. Final Technical Report for SBIR entitled Four-Dimensional Finite-Orbit-Width Fokker-Planck Code with Sources, for Neoclassical/Anomalous Transport Simulation of Ion and Electron Distributions

    SciTech Connect (OSTI)

    Harvey, R. W.; Petrov, Yu. V.

    2013-12-03

    Within the US Department of Energy/Office of Fusion Energy magnetic fusion research program, there is an important whole-plasma-modeling need for a radio-frequency/neutral-beam-injection (RF/NBI) transport-oriented finite-difference Fokker-Planck (FP) code with combined capabilities for 4D (2R2V) geometry near the fusion plasma periphery, and computationally less demanding 3D (1R2V) bounce-averaged capabilities for plasma in the core of fusion devices. Demonstration of proof-of-principle achievement of this goal has been carried out in research carried out under Phase I of the SBIR award. Two DOE-sponsored codes, the CQL3D bounce-average Fokker-Planck code in which CompX has specialized, and the COGENT 4D, plasma edge-oriented Fokker-Planck code which has been constructed by Lawrence Livermore National Laboratory and Lawrence Berkeley Laboratory scientists, where coupled. Coupling was achieved by using CQL3D calculated velocity distributions including an energetic tail resulting from NBI, as boundary conditions for the COGENT code over the two-dimensional velocity space on a spatial interface (flux) surface at a given radius near the plasma periphery. The finite-orbit-width fast ions from the CQL3D distributions penetrated into the peripheral plasma modeled by the COGENT code. This combined code demonstrates the feasibility of the proposed 3D/4D code. By combining these codes, the greatest computational efficiency is achieved subject to present modeling needs in toroidally symmetric magnetic fusion devices. The more efficient 3D code can be used in its regions of applicability, coupled to the more computationally demanding 4D code in higher collisionality edge plasma regions where that extended capability is necessary for accurate representation of the plasma. More efficient code leads to greater use and utility of the model. An ancillary aim of the project is to make the combined 3D/4D code user friendly. Achievement of full-coupling of these two Fokker

  13. FLUKA: A Multi-Particle Transport Code

    SciTech Connect (OSTI)

    Ferrari, A.; Sala, P.R.; Fasso, A.; Ranft, J.; /Siegen U.

    2005-12-14

    This report describes the 2005 version of the Fluka particle transport code. The first part introduces the basic notions, describes the modular structure of the system, and contains an installation and beginner's guide. The second part complements this initial information with details about the various components of Fluka and how to use them. It concludes with a detailed history and bibliography.

  14. DYNA3D Code Practices and Developments

    SciTech Connect (OSTI)

    Lin, L.; Zywicz, E.; Raboin, P.

    2000-04-21

    DYNA3D is an explicit, finite element code developed to solve high rate dynamic simulations for problems of interest to the engineering mechanics community. The DYNA3D code has been under continuous development since 1976[1] by the Methods Development Group in the Mechanical Engineering Department of Lawrence Livermore National Laboratory. The pace of code development activities has substantially increased in the past five years, growing from one to between four and six code developers. This has necessitated the use of software tools such as CVS (Concurrent Versions System) to help manage multiple version updates. While on-line documentation with an Adobe PDF manual helps to communicate software developments, periodically a summary document describing recent changes and improvements in DYNA3D software is needed. The first part of this report describes issues surrounding software versions and source control. The remainder of this report details the major capability improvements since the last publicly released version of DYNA3D in 1996. Not included here are the many hundreds of bug corrections and minor enhancements, nor the development in DYNA3D between the manual release in 1993[2] and the public code release in 1996.

  15. MELCOR Accident Consequence Code System (MACCS)

    SciTech Connect (OSTI)

    Chanin, D.I. ); Sprung, J.L.; Ritchie, L.T.; Jow, Hong-Nian )

    1990-02-01

    This report describes the MACCS computer code. The purpose of this code is to simulate the impact of severe accidents at nuclear power plants on the surrounding environment. MACCS has been developed for the US Nuclear Regulatory Commission to replace the previous CRAC2 code, and it incorporates many improvements in modeling flexibility in comparison to CRAC2. The principal phenomena considered in MACCS are atmospheric transport, mitigative actions based on dose projection, dose accumulation by a number of pathways including food and water ingestion, early and latent health effects, and economic costs. The MACCS code can be used for a variety of applications. These include (1) probabilistic risk assessment (PRA) of nuclear power plants and other nuclear facilities, (2) sensitivity studies to gain a better understanding of the parameters important to PRA, and (3) cost-benefit analysis. This report is composed of three volumes. This document, Volume 1, the Users's Guide, describes the input data requirements of the MACCS code and provides directions for its use as illustrated by three sample problems.

  16. Finite Element Analysis Code

    Energy Science and Technology Software Center (OSTI)

    2006-03-08

    MAPVAR-KD is designed to transfer solution results from one finite element mesh to another. MAPVAR-KD draws heavily from the structure and coding of MERLIN II, but it employs a new finite element data base, EXODUS II, and offers enhanced speed and new capabilities not available in MERLIN II. In keeping with the MERLIN II documentation, the computational algorithms used in MAPVAR-KD are described. User instructions are presented. Example problems are included to demonstrate the operationmore » of the code and the effects of various input options. MAPVAR-KD is a modification of MAPVAR in which the search algorithm was replaced by a kd-tree-based search for better performance on large problems.« less

  17. Confocal coded aperture imaging

    DOE Patents [OSTI]

    Tobin, Jr., Kenneth William (Harriman, TN); Thomas, Jr., Clarence E. (Knoxville, TN)

    2001-01-01

    A method for imaging a target volume comprises the steps of: radiating a small bandwidth of energy toward the target volume; focusing the small bandwidth of energy into a beam; moving the target volume through a plurality of positions within the focused beam; collecting a beam of energy scattered from the target volume with a non-diffractive confocal coded aperture; generating a shadow image of said aperture from every point source of radiation in the target volume; and, reconstructing the shadow image into a 3-dimensional image of the every point source by mathematically correlating the shadow image with a digital or analog version of the coded aperture. The method can comprise the step of collecting the beam of energy scattered from the target volume with a Fresnel zone plate.

  18. Discussion on a Code Comparison Effort for the Geothermal Technologies

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Program | Department of Energy Discussion on a Code Comparison Effort for the Geothermal Technologies Program Discussion on a Code Comparison Effort for the Geothermal Technologies Program Code comparison presentation by Mark White of PNNL at the 2012 Peer Review meeting on May 10. gtp_2012peerreview_pnnl_white.pdf (2.85 MB) More Documents & Publications PNNL Support of the DOE GTO Model Comparison Activity Fiscal Year 2014 ASCEM Status Report Reservoir Modeling Working Group Meeting

  19. Technical Standards, Safety Analysis Toolbox Codes - November 2003 |

    Office of Environmental Management (EM)

    Department of Energy Standards, Safety Analysis Toolbox Codes - November 2003 Technical Standards, Safety Analysis Toolbox Codes - November 2003 November 2003 Software Quality Assurance Plan and Criteria for the Safety Analysis Toolbox Codes Safety analysis software for the DOE "toolbox" was designated by DOE/EH in March 2003 (DOE/EH, 2003). The supporting basis for this designation was provided by a DOE-chartered Safety Analysis Software Group in the technical report, Selection of

  20. Microsoft Word - Energy Code Enforcement Funding Task Force - Fact Sheet

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    [Final].docx | Department of Energy Energy Code Enforcement Funding Task Force - Fact Sheet [Final].docx Microsoft Word - Energy Code Enforcement Funding Task Force - Fact Sheet [Final].docx Microsoft Word - Energy Code Enforcement Funding Task Force - Fact Sheet [Final].docx (221.19 KB) More Documents & Publications Sonoma County Solar Implementation Plan Final Report - Grow Solar Wisconsin Team Energy Industry Days Additional Information

  1. Coding Archives - Nercenergy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Coding What Certificates Should My Microsoft Exchange Server Have? Much like any other network application, in order to secure the functionality and safety of Microsoft Exchange Servers, it's essential to adopt specific certificates. Due to the literally thousands, if not millions, of security threats bombarding your Exchange Server every day, these certificates ensure users have a safe messaging experience while simultaneously safeguarding your data and sensitive information from being

  2. THREAT OF MALICIOUS CODE

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    THREAT OF MALICIOUS CODE The Department of Energy (DOE) is strongly committed to the protection of all DOE assets from cyber attack and malicious exploitation. This includes information, networks, hardware, software, and mobile devices. DOE's continued diligence in this arena is critical in today's constantly-evolving cyber threat landscape. A recently cited incident involved senior officials receiving unsolicited free phone chargers. Luckily, the source was legitimate and did not result in a

  3. MELCOR computer code manuals

    SciTech Connect (OSTI)

    Summers, R.M.; Cole, R.K. Jr.; Smith, R.C.; Stuart, D.S.; Thompson, S.L.; Hodge, S.A.; Hyman, C.R.; Sanders, R.L.

    1995-03-01

    MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. MELCOR is being developed at Sandia National Laboratories for the U.S. Nuclear Regulatory Commission as a second-generation plant risk assessment tool and the successor to the Source Term Code Package. A broad spectrum of severe accident phenomena in both boiling and pressurized water reactors is treated in MELCOR in a unified framework. These include: thermal-hydraulic response in the reactor coolant system, reactor cavity, containment, and confinement buildings; core heatup, degradation, and relocation; core-concrete attack; hydrogen production, transport, and combustion; fission product release and transport; and the impact of engineered safety features on thermal-hydraulic and radionuclide behavior. Current uses of MELCOR include estimation of severe accident source terms and their sensitivities and uncertainties in a variety of applications. This publication of the MELCOR computer code manuals corresponds to MELCOR 1.8.3, released to users in August, 1994. Volume 1 contains a primer that describes MELCOR`s phenomenological scope, organization (by package), and documentation. The remainder of Volume 1 contains the MELCOR Users Guides, which provide the input instructions and guidelines for each package. Volume 2 contains the MELCOR Reference Manuals, which describe the phenomenological models that have been implemented in each package.

  4. Bar coded retroreflective target

    DOE Patents [OSTI]

    Vann, Charles S.

    2000-01-01

    This small, inexpensive, non-contact laser sensor can detect the location of a retroreflective target in a relatively large volume and up to six degrees of position. The tracker's laser beam is formed into a plane of light which is swept across the space of interest. When the beam illuminates the retroreflector, some of the light returns to the tracker. The intensity, angle, and time of the return beam is measured to calculate the three dimensional location of the target. With three retroreflectors on the target, the locations of three points on the target are measured, enabling the calculation of all six degrees of target position. Until now, devices for three-dimensional tracking of objects in a large volume have been heavy, large, and very expensive. Because of the simplicity and unique characteristics of this tracker, it is capable of three-dimensional tracking of one to several objects in a large volume, yet it is compact, light-weight, and relatively inexpensive. Alternatively, a tracker produces a diverging laser beam which is directed towards a fixed position, and senses when a retroreflective target enters the fixed field of view. An optically bar coded target can be read by the tracker to provide information about the target. The target can be formed of a ball lens with a bar code on one end. As the target moves through the field, the ball lens causes the laser beam to scan across the bar code.

  5. Health Code Number (HCN) Development Procedure

    SciTech Connect (OSTI)

    Petrocchi, Rocky; Craig, Douglas K.; Bond, Jayne-Anne; Trott, Donna M.; Yu, Xiao-Ying

    2013-09-01

    This report provides the detailed description of health code numbers (HCNs) and the procedure of how each HCN is assigned. It contains many guidelines and rationales of HCNs. HCNs are used in the chemical mixture methodology (CMM), a method recommended by the department of energy (DOE) for assessing health effects as a result of exposures to airborne aerosols in an emergency. The procedure is a useful tool for proficient HCN code developers. Intense training and quality assurance with qualified HCN developers are required before an individual comprehends the procedure to develop HCNs for DOE.

  6. Idaho Code | Open Energy Information

    Open Energy Info (EERE)

    Not provided DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for Idaho Code Citation Idaho Code (2014). Retrieved from "http:en.openei.org...

  7. Software quality and process improvement in scientific simulation codes

    SciTech Connect (OSTI)

    Ambrosiano, J.; Webster, R.

    1997-11-01

    This report contains viewgraphs on the quest to develope better simulation code quality through process modeling and improvement. This study is based on the experience of the authors and interviews with ten subjects chosen from simulation code development teams at LANL. This study is descriptive rather than scientific.

  8. Sandia National Laboratories analysis code data base

    SciTech Connect (OSTI)

    Peterson, C.W.

    1994-11-01

    Sandia National Laboratories, mission is to solve important problems in the areas of national defense, energy security, environmental integrity, and industrial technology. The Laboratories` strategy for accomplishing this mission is to conduct research to provide an understanding of the important physical phenomena underlying any problem, and then to construct validated computational models of the phenomena which can be used as tools to solve the problem. In the course of implementing this strategy, Sandia`s technical staff has produced a wide variety of numerical problem-solving tools which they use regularly in the design, analysis, performance prediction, and optimization of Sandia components, systems and manufacturing processes. This report provides the relevant technical and accessibility data on the numerical codes used at Sandia, including information on the technical competency or capability area that each code addresses, code ``ownership`` and release status, and references describing the physical models and numerical implementation.

  9. Reports

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Submittal Letter (pdf) Appendix A (xls) AnchoChaquehui Watershed PCB Report Polychlorinated Biphenyls in Precipitation and Stormwater within the Upper Rio Grande Watershed (pdf) ...

  10. JOY computer code

    SciTech Connect (OSTI)

    Couch, R.G.; Albright, E.L.; Alexander, N.B.

    1983-01-01

    JOY is a 3-dimensional multifluid Eulerian hydrocode in Cartesian coordinates. It contains an elastic-plastic treatment and a shock-initiation model for high explosives (HE). Development of JOY was funded by the Ballistic Missile Defense Advanced Technology Center (BMDATC). The intended use of the code was for the study of hypervelocity impacts. The ultimate goal was to perform a structural analysis of objects subject to such impacts. JOY was designed to treat the early-impact phases where material motion is complicated, and then transfer information to DYNA3D for the longer-timescale analysis.

  11. Finite Element Analysis Code

    Energy Science and Technology Software Center (OSTI)

    2005-06-26

    Exotxt is an analysis code that reads finite element results data stored in an exodusII file and generates a file in a structured text format. The text file can be edited or modified via a number of text formatting tools. Exotxt is used by analysis to translate data from the binary exodusII format into a structured text format which can then be edited or modified and then either translated back to exodusII format or tomore » another format.« less

  12. Finite Element Analysis Code

    Energy Science and Technology Software Center (OSTI)

    2005-05-07

    CONEX is a code for joining sequentially in time multiple exodusll database files which all represent the same base mesh topology and geometry. It is used to create a single results or restart file from multiple results or restart files which typically arise as the result of multiple restarted analyses. CONEX is used to postprocess the results from a series of finite element analyses. It can join sequentially the data from multiple results databases intomore » a single database which makes it easier to postprocess the results data.« less

  13. Bar code application to nuclear material accountancy

    SciTech Connect (OSTI)

    Usui, S.; Sano, H. )

    1991-01-01

    For the purpose of efficient implementation of IAEA safeguards inspection, operators ought to prepare the information which is related to the strata for flow verification in a timely manner, such as physical inventory listing and summary of the fuel bundles. Today the use of bar code technique in tracing of products related data or counting number of items has been more and more applied to many facets of industry. From these points of view, the Japan Nuclear Fuel Company (NF) has been developing JNF Total Bar Code System. Now JNF has established an on-line input system of the fuel bundle accountability data by use of the bar code system to quickly prepare the information necessary for the inspection. As the first step, JNF implemented this bar code system at the flow verification to prepare physical inventory summary and location map of the fuel bundles in the storage. This paper reports that as a result of this, NF confirmed that this bar code system made it possible to input easily and quickly nuclear material accountancy information, and therefore this system is utilized as an effective and efficient measure of timely preparation for the inspection.

  14. Benchmarking NNWSI flow and transport codes: COVE 1 results

    SciTech Connect (OSTI)

    Hayden, N.K.

    1985-06-01

    The code verification (COVE) activity of the Nevada Nuclear Waste Storage Investigations (NNWSI) Project is the first step in certification of flow and transport codes used for NNWSI performance assessments of a geologic repository for disposing of high-level radioactive wastes. The goals of the COVE activity are (1) to demonstrate and compare the numerical accuracy and sensitivity of certain codes, (2) to identify and resolve problems in running typical NNWSI performance assessment calculations, and (3) to evaluate computer requirements for running the codes. This report describes the work done for COVE 1, the first step in benchmarking some of the codes. Isothermal calculations for the COVE 1 benchmarking have been completed using the hydrologic flow codes SAGUARO, TRUST, and GWVIP; the radionuclide transport codes FEMTRAN and TRUMP; and the coupled flow and transport code TRACR3D. This report presents the results of three cases of the benchmarking problem solved for COVE 1, a comparison of the results, questions raised regarding sensitivities to modeling techniques, and conclusions drawn regarding the status and numerical sensitivities of the codes. 30 refs.

  15. UNSAT-H, an unsaturated soil water flow code for use at the Hanford site: code documentation

    SciTech Connect (OSTI)

    Fayer, M.J.; Gee, G.W.

    1985-10-01

    The unsaturated soil moisture flow code, UNSAT-H, which was developed at Pacific Northwest Laboratory for assessing water movement at waste sites on the Hanford site, is documented in this report. This code is used in simulating the water dynamics of arid sites under consideration for waste disposal. The results of an example simulation of constant infiltration show excellent agreement with an analytical solution and another numerical solution, thus providing some verification of the UNSAT-H code. Areas of the code are identified for future work and include runoff, snowmelt, long-term climate and plant models, and parameter measurement. 29 refs., 7 figs., 2 tabs.

  16. Vehicle Codes and Standards: Overview and Gap Analysis

    SciTech Connect (OSTI)

    Blake, C.; Buttner, W.; Rivkin, C.

    2010-02-01

    This report identifies gaps in vehicle codes and standards and recommends ways to fill the gaps, focusing on six alternative fuels: biodiesel, natural gas, electricity, ethanol, hydrogen, and propane.

  17. " Row: NAICS Codes;" " ...

    U.S. Energy Information Administration (EIA) Indexed Site

    ... for which" "payment was not made, quantities purchased centrally within the company but separate" "from the reporting establishment, and quantities for which payment was made ...

  18. Southeast Energy Efficiency Alliance's Building Energy Codes...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Southeast Energy Efficiency Alliance's Building Energy Codes Project Southeast Energy Efficiency Alliance's Building Energy Codes Project Building Codes Project for the 2013 ...

  19. Product Service Codes @ Headquarters | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Service Codes @ Headquarters A listing of Product Service Codes used at Headquarters Procurement Services PDF icon Produce Service Codes @ Headquarters.pdf More Documents &...

  20. Utah Code Annotated | Open Energy Information

    Open Energy Info (EERE)

    Code Ann. DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for Utah Code Annotated Citation Utah Code Annotated (2014). Retrieved from...

  1. Cal. Wat. Code 13376 | Open Energy Information

    Open Energy Info (EERE)

    Cal. Wat. Code 13376Legal Abstract Cal. Wat. Code 13376, current through August 14, 2014. Published NA Year Signed or Took Effect 2014 Legal Citation Cal. Wat. Code...

  2. Cal. Wat. Code 13320 | Open Energy Information

    Open Energy Info (EERE)

    Cal. Wat. Code 13320Legal Abstract Cal. Wat. Code 13320, current through August 13, 2014. Published NA Year Signed or Took Effect 1969 Legal Citation Cal. Wat. Code...

  3. Cal. Wat. Code 13369 | Open Energy Information

    Open Energy Info (EERE)

    Cal. Wat. Code 13369Legal Abstract Cal. Wat. Code 13369, current through August 13, 2014. Published NA Year Signed or Took Effect 1969 Legal Citation Cal. Wat. Code...

  4. Cal. Wat. Code 13373 | Open Energy Information

    Open Energy Info (EERE)

    Cal. Wat. Code 13373Legal Abstract Cal. Wat. Code 13373, current through August 14, 2014. Published NA Year Signed or Took Effect 1987 Legal Citation Cal. Wat. Code...

  5. Cal. Wat. Code 13160 | Open Energy Information

    Open Energy Info (EERE)

    Cal. Wat. Code 13160Legal Abstract Cal. Wat. Code 13160, current through August 13, 2014. Published NA Year Signed or Took Effect 1969 Legal Citation Cal. Wat. Code...

  6. Early User Experience with BISON Fuel Performance Code

    SciTech Connect (OSTI)

    D. M. Perez

    2012-08-01

    Three Fuel Modeling Exercise II (FUMEX II) LWR fuel irradiation experiments were simulated and analyzed using the fuel performance code BISON to demonstrate code utility for modeling of the LWR fuel performance. Comparisons were made against the BISON results and the experimental data for the three assessment cases. The assessment cases reported within this report include IFA-597.3 Rod 8, Riso AN3 and Riso AN4.

  7. Explosive Formulation Code Naming SOP

    SciTech Connect (OSTI)

    Martz, H. E.

    2014-09-19

    The purpose of this SOP is to provide a procedure for giving individual HME formulations code names. A code name for an individual HME formulation consists of an explosive family code, given by the classified guide, followed by a dash, -, and a number. If the formulation requires preparation such as packing or aging, these add additional groups of symbols to the X-ray specimen name.

  8. Preserving Envelope Efficiency in Performance Based Code Compliance

    SciTech Connect (OSTI)

    Thornton, Brian A.; Sullivan, Greg P.; Rosenberg, Michael I.; Baechler, Michael C.

    2015-06-20

    The City of Seattle 2012 Energy Code (Seattle 2014), one of the most progressive in the country, is under revision for its 2015 edition. Additionally, city personnel participate in the development of the next generation of the Washington State Energy Code and the International Energy Code. Seattle has pledged carbon neutrality by 2050 including buildings, transportation and other sectors. The United States Department of Energy (DOE), through Pacific Northwest National Laboratory (PNNL) provided technical assistance to Seattle in order to understand the implications of one potential direction for its code development, limiting trade-offs of long-lived building envelope components less stringent than the prescriptive code envelope requirements by using better-than-code but shorter-lived lighting and heating, ventilation, and air-conditioning (HVAC) components through the total building performance modeled energy compliance path. Weaker building envelopes can permanently limit building energy performance even as lighting and HVAC components are upgraded over time, because retrofitting the envelope is less likely and more expensive. Weaker building envelopes may also increase the required size, cost and complexity of HVAC systems and may adversely affect occupant comfort. This report presents the results of this technical assistance. The use of modeled energy code compliance to trade-off envelope components with shorter-lived building components is not unique to Seattle and the lessons and possible solutions described in this report have implications for other jurisdictions and energy codes.

  9. City of Austin- Zoning Code

    Broader source: Energy.gov [DOE]

    The Zoning Code also allows for preservation plans in historic districts to incorporate sustainability measures such as solar technologies and other energy generation and efficiency measures.

  10. Technical Assistance: Increasing Code Compliance

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technologies Office Peer Review Rosemarie Bartlett ... energy codes resulting in higher-performing buildings that ... feedback * Provide education and training materials in ...

  11. NEEP Building Energy Codes Project

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    * Markets value and prioritize energy efficiency - Rating and Disclosure ( VT, Cambridge, MA) * Robust & qualified building energy code work force: DE, RI, MA, MD, NY * ...

  12. Marin County- Solar Access Code

    Broader source: Energy.gov [DOE]

    Marin County's Energy Conservation Code is designed to assure new subdivisions provide for future passive or natural heating or cooling opportunities in the subdivision to the extent feasible. ...

  13. Clark County- Energy Conservation Code

    Broader source: Energy.gov [DOE]

    In September 2010, Clark County adopted Ordinance 3897, implementing the Southern Nevada version of the 2009 International Energy Conservation Code for both residential and commercial buildings...

  14. Telescope Adaptive Optics Code

    Energy Science and Technology Software Center (OSTI)

    2005-07-28

    The Telescope AO Code has general adaptive optics capabilities plus specialized models for three telescopes with either adaptive optics or active optics systems. It has the capability to generate either single-layer or distributed Kolmogorov turbulence phase screens using the FFT. Missing low order spatial frequencies are added using the Karhunen-Loeve expansion. The phase structure curve is extremely dose to the theoreUcal. Secondly, it has the capability to simulate an adaptive optics control systems. The defaultmore » parameters are those of the Keck II adaptive optics system. Thirdly, it has a general wave optics capability to model the science camera halo due to scintillation from atmospheric turbulence and the telescope optics. Although this capability was implemented for the Gemini telescopes, the only default parameter specific to the Gemini telescopes is the primary mirror diameter. Finally, it has a model for the LSST active optics alignment strategy. This last model is highly specific to the LSST« less

  15. Verification of the BISON fuel performance code

    SciTech Connect (OSTI)

    D. M. Perez; R. J. Gardner; J. D. Hales; S. R. Novascone; G. Pastore; B. W. Spencer; R. L. Williamson

    2014-09-01

    BISON is a modern finite element-based nuclear fuel performance code that has been under development at Idaho National Labo- ratory (USA) since 2009. The code is applicable to both steady and transient fuel behavior and is used to analyze 1D spherical, 2D axisymmetric, or 3D geometries. BISON has been applied to a variety of fuel forms including LWR fuel rods, TRISO-coated fuel particles, and metallic fuel in both rod and plate geometries. Code validation is currently in progress, principally by comparison to instrumented LWR fuel rods and other well known fuel performance codes. Results from several assessment cases are reported, with emphasis on fuel centerline temperatures at various stages of fuel life, fission gas release, and clad deformation during pellet clad mechanical interaction (PCMI). BISON comparisons to fuel centerline temperature measurements are very good at beginning of life and reasonable at high burnup. Although limited to date, fission gas release comparisons are very good. Comparisons of rod diameter following significant power ramping are also good and demonstrate BISONs unique ability to model discrete pellet behavior and accurately predict clad ridging from PCMI.

  16. REPORT

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DOE/NV/11718-387 ECOLOGICAL MONITORING AND COMPLIANCE PROGRAM FISCAL YEAR 1999 REPORT December 1999 Prepared by Ecological Services P.O. Box 98521 Las Vegas, NV 89193-8521 DISCLAIMER STATEMENT Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement, recommendation, or favoring by the U.S. Government or any agency thereof or its contractors or subcontractors.

  17. MUXS: a code to generate multigroup cross sections for sputtering calculations

    SciTech Connect (OSTI)

    Hoffman, T.J.; Robinson, M.T.; Dodds, H.L. Jr.

    1982-10-01

    This report documents MUXS, a computer code to generate multigroup cross sections for charged particle transport problems. Cross sections generated by MUXS can be used in many multigroup transport codes, with minor modifications to these codes, to calculate sputtering yields, reflection coefficients, penetration distances, etc.

  18. ACCELERATION PHYSICS CODE WEB REPOSITORY.

    SciTech Connect (OSTI)

    WEI, J.

    2006-06-26

    In the framework of the CARE HHH European Network, we have developed a web-based dynamic accelerator-physics code repository. We describe the design, structure and contents of this repository, illustrate its usage, and discuss our future plans, with emphasis on code benchmarking.

  19. Accelerator Physics Code Web Repository

    SciTech Connect (OSTI)

    Zimmermann, F.; Basset, R.; Bellodi, G.; Benedetto, E.; Dorda, U.; Giovannozzi, M.; Papaphilippou, Y.; Pieloni, T.; Ruggiero, F.; Rumolo, G.; Schmidt, F.; Todesco, E.; Zotter, B.W.; Payet, J.; Bartolini, R.; Farvacque, L.; Sen, T.; Chin, Y.H.; Ohmi, K.; Oide, K.; Furman, M.; /LBL, Berkeley /Oak Ridge /Pohang Accelerator Lab. /SLAC /TRIUMF /Tech-X, Boulder /UC, San Diego /Darmstadt, GSI /Rutherford /Brookhaven

    2006-10-24

    In the framework of the CARE HHH European Network, we have developed a web-based dynamic accelerator-physics code repository. We describe the design, structure and contents of this repository, illustrate its usage, and discuss our future plans, with emphasis on code benchmarking.

  20. Code and model extensions of the THATCH code for modular high temperature gas-cooled reactors

    SciTech Connect (OSTI)

    Kroger, P.G.; Kennett, R.J. )

    1993-05-01

    This report documents several model extensions and improvements of the THATCH code, a code to model thermal and fluid flow transients in High Temperature Gas-Cooled Reactors. A heat exchanger model was added, which can be used to represent the steam generator of the main Heat Transport System or the auxiliary Shutdown Cooling System. This addition permits the modeling of forced flow cooldown transients with the THATCH code. An enhanced upper head model, considering the actual conical and spherical shape of the upper plenum and reactor upper head was added, permitting more accurate modeling of the heat transfer in thisregion. The revised models are described, and the changes and addition to the input records are documented.

  1. Software and codes for analysis of concentrating solar power technologies.

    SciTech Connect (OSTI)

    Ho, Clifford Kuofei

    2008-12-01

    This report presents a review and evaluation of software and codes that have been used to support Sandia National Laboratories concentrating solar power (CSP) program. Additional software packages developed by other institutions and companies that can potentially improve Sandia's analysis capabilities in the CSP program are also evaluated. The software and codes are grouped according to specific CSP technologies: power tower systems, linear concentrator systems, and dish/engine systems. A description of each code is presented with regard to each specific CSP technology, along with details regarding availability, maintenance, and references. A summary of all the codes is then presented with recommendations regarding the use and retention of the codes. A description of probabilistic methods for uncertainty and sensitivity analyses of concentrating solar power technologies is also provided.

  2. Portable code development in C

    SciTech Connect (OSTI)

    Brown, S.A.

    1990-11-06

    With a new generation of high performance computers appearing around us on a time scale of months, a new challenge for developers of simulation codes is to write and maintain production codes that are both highly portable and maximally efficient. My contention is that C is the language that is both best suited to that goal and is widely available today. GLF is a new code written mainly in C which is intended to have all of the XRASER physics and run on any platform of interest. It demonstrates the power of the C paradigm for code developers and flexibility and ease of use for the users. Three fundamental problems are discussed: the C/UNIX development environment; the supporting tools and libraries which handle data and graphics portability issues; and the advantages of C in numerical simulation code development.

  3. Local invariants of stabilizer codes

    SciTech Connect (OSTI)

    Nest, Maarten van den; Dehaene, Jeroen; Moor, Bart de

    2004-09-01

    In Phys. Rev. A 58, 1833 (1998), Grassl et al. presented a family of polynomial invariants which separate the orbits of multiqubit density operators {rho} under the action of the local unitary group. We consider this family of invariants for the class of those {rho} that are the projection operators describing stabilizer codes and give a complete translation of these invariants into the binary framework in which stabilizer codes are usually described. Such an investigation of local invariants of quantum codes is of natural importance in quantum coding theory, since locally equivalent codes have the same error-correcting capabilities and local invariants are powerful tools to explore their structure. Moreover, the present result is relevant in the context of multipartite entanglement and the development of the measurement-based model of quantum computation known as the one-way quantum computer.

  4. U-136: Adobe Flash Player Lets Remote Users Execute Arbitrary Code

    Broader source: Energy.gov [DOE]

    Two vulnerabilities were reported in Adobe Flash Player. A remote user can cause arbitrary code to be executed on the target user's system.

  5. U-110: Samba Bug Lets Remote Users Execute Arbitrary Code | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    code on the target system. reference LINKS: Vendor Advisory Security Tracker ID 1026739 CVE-2012-0870 IMPACT ASSESSMENT: Medium Discussion: A vulnerability was reported in Samba....

  6. U-166: Adobe Shockwave Player Memory Corruption Flaws Let Remote Users Execute Arbitrary Code

    Broader source: Energy.gov [DOE]

    Multiple vulnerabilities were reported in Adobe Shockwave Player. A remote user can cause arbitrary code to be executed on the target user's system.

  7. U-170: Apple QuickTime Multiple Flaws Let Remote Users Execute Arbitrary Code

    Broader source: Energy.gov [DOE]

    Multiple vulnerabilities were reported in Apple QuickTime. A remote user can cause arbitrary code to be executed on the target user's system.

  8. V-006: CA ARCserve Backup Flaws Let Remote Users Execute Arbitrary Code and Deny Service

    Broader source: Energy.gov [DOE]

    Two vulnerabilities were reported in CA ARCserve Backup. A remote user can execute arbitrary code on the target system. A remote user can cause denial of service conditions.

  9. U-080: Linux Kernel XFS Heap Overflow May Let Remote Users Execute Arbitrary Code

    Broader source: Energy.gov [DOE]

    A vulnerability was reported in the Linux Kernel. A remote user can cause arbitrary code to be executed on the target user's system.

  10. T-538: HP OpenView Storage Data Protector Bug Lets Remote Users Execute Arbitrary Code

    Broader source: Energy.gov [DOE]

    A vulnerability was reported in HP OpenView Storage Data Protector. A remote user can execute arbitrary code on the target system.