National Library of Energy BETA

Sample records for removing tall growing

  1. Schematic design of distributed mass damping systems for tall buildings

    E-Print Network [OSTI]

    Silbiger, Jason Stahl

    2014-01-01

    As new high-rises grow taller and more slender, the design of tall buildings becomes heavily constrained by the control of lateral displacements and accelerations due to dynamic excitations. This has led to the development ...

  2. Chemical composition of biomass from tall perennial tropical grasses

    SciTech Connect (OSTI)

    Prine, G.M.; Stricker, J.A.; Anderson, D.L.

    1995-11-01

    The tall perennial tropical grasses, elephantgrass (Pennisetum purpureum Schum.), sugarcane and energycane (Saccharum sp.) and erianthus (Erianthus arundenaceum (Retz) Jesw.) have given very high oven dry biomass yields in Florida and the warm Lower South USA. No good complete analyses of the chemical composition of these grasses for planning potential energy use was available. We sampled treatments of several tall grass demonstrations and experiments containing high-biomass yielding genotypes of the above tall grass crops at several locations in Florida over the two growing seasons, 1992 and 1993. These samples were analyzed for crude protein, NDF, ADF, cellulose, hemicellulose, lignin, and IVDMD or IVOMD. The analysis for the above constituents are reported, along with biomass yields where available, for the tall grass accessions in the various demonstrations and experiments. Particular attention is given to values obtained from the high-yielding tall grasses grown on phosphatic clays in Polk County, FL, the area targeted by a NREL grant to help commercialize bioenergy use from these crops.

  3. Tall building collapse mechanisms initiated by fire 

    E-Print Network [OSTI]

    Usmani, Asif; Roben, Charlotte; Johnston, Louise; Flint, Graeme

    This paper introduces the hypothesis of two possible failure mechanisms for tall buildings in multiple floor fires. This paper extends the previous work done on the WTC towers by investigating more "generic" tall building frames made of standard...

  4. Scientific American: "Tall Trees Sucked Dry by Global Warming...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Scientific American: "Tall Trees Sucked Dry by Global Warming" June 7, 2015 Scientific American: "Tall Trees Sucked Dry by Global Warming" A well-known scientific principle...

  5. Scientific American: "Tall Trees Sucked Dry by Global Warming...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dry by Global Warming" Scientific American: "Tall Trees Sucked Dry by Global Warming" Climate change will challenge tall trees like California's redwoods. June 7, 2015...

  6. Internal tide generation by tall ocean ridges

    E-Print Network [OSTI]

    Echeverri Mondragón, Paula

    2009-01-01

    Internal tides are internal waves of tidal period generated by tidal currents flowing over submarine topography. Tall ridges that are nominally two-dimensional (2-D) are sites of particularly strong generation. The subsequent ...

  7. Dynamic interrelationship between technology and architecture in tall buildings

    E-Print Network [OSTI]

    Moon, Kyoung-Sun

    2005-01-01

    The interrelationship between the technology and architecture of tall buildings is investigated from the emergence of tall buildings in the late 19th century to the present. Through the historical research, a filtering ...

  8. Leucaena and tall grasses as energy crops in humid lower south USA

    SciTech Connect (OSTI)

    Prine, G.M.; Woodard, K.R.; Cunilio, T.V.

    1994-12-31

    The tropical leguminous shrub/tree, leucaena (Leucaena spp. mainly leucocephala), and perennial tropical tall grasses such as elephantgrass (Pennisetum purpureum), sugarcane, and energycane (Saccharum spp.) are well adapted to the long growing seasons and high rainfall of the humid lower South. In much of the area the topgrowth is killed by frost during winter and plants regenerate from underground parts in spring. Selected accessions from a duplicated 373 accession leucaena nursery had an average annual woody stem dry matter production of 31.4 Mg ha{sup -1}. Average oven dry stem wood yields from selected accessions adjusted for environmental enrichment over the 4 growth seasons were 78.9 Mg ha{sup -1} total and average annual yield of 19.7 Mg ha{sup -1}. The tall perennial grasses have linear growth rates of 18 to 27 g m{sup 2}d{sup -1} for long periods (140 to 196 d and sometimes longer) each season. Oven dry biomass yields of tall grasses have varied from 20 to 45 Mg ha{sup -1} in mild temperature locations to over 60 Mg ha{sup -1} yr{sup -1} in warm subtropics of the lower Florida peninsula. Tall grasses and leucaena, once established, may persist for many seasons. A map showing the possible range of the crops in lower South is shown. Highest biomass yields of tall grasses have been produced when irrigated with sewage effluent or when grown on phosphatic clay and muck soils of south Florida. Several companies are considering using leucaena and/or tall grasses for bioenergy in the phosphatic mining area of Polk County, Florida.

  9. Tall Corn Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page| Open Energy Information Serbia-Enhancing CapacityVectren)ModelTalbotts Ltd Jump to: navigation, searchTall Corn

  10. Analysis of the structural response of tall buildings under multifloor and travelling fires 

    E-Print Network [OSTI]

    Kotsovinos, Panagiotis

    2013-07-01

    The last decades have seen a surge in the construction of tall buildings all over the world. Due to their, often, innovative and complex layouts, tall buildings can pose unique challenges to architects and engineers. ...

  11. DOWNSTREAM CHANNEL CHANGES AFTER A SMALL DAM REMOVAL: USING AERIAL PHOTOS AND MEASUREMENT ERROR FOR CONTEXT;

    E-Print Network [OSTI]

    Tullos, Desiree

    DOWNSTREAM CHANNEL CHANGES AFTER A SMALL DAM REMOVAL: USING AERIAL PHOTOS AND MEASUREMENT ERROR and Ecological Engineering, Oregon State University, Corvallis, OR, USA ABSTRACT Dam removal is often implemented to assess downstream channel changes associated with a small dam removal. The Brownsville Dam, a 2.1 m tall

  12. Fire Safety Challenges of Tall Wood Final Report

    E-Print Network [OSTI]

    Fire Safety Challenges of Tall Wood Buildings Final Report Prepared by: Robert Gerard and David Barber Arup North America Ltd San Francisco, CA Armin Wolski San Francisco, CA © December 2013 Fire Protection Research Foundation THE FIRE PROTECTION RESEARCH FOUNDATION ONE BATTERYMARCH PARK QUINCY

  13. Process for tertiary oil recovery using tall oil pitch

    DOE Patents [OSTI]

    Radke, C.J.

    1983-07-25

    A process and compositions for enhancing the recovery of acid crudes are disclosed. The process involves injecting caustic solutions into the reservoir to maintain a pH of 11 to 13. The fluid contains an effective amount of multivalent cation for inhibiting alkaline silica dissolution with the reservoir. A tall oil pitch soap is added as a polymeric mobility control agent. (DMC)

  14. How tall is the White Ash tree? White Ash tree

    E-Print Network [OSTI]

    Ashline, George

    How tall is the White Ash tree? White Ash tree Sapling Activity Tree location Try this: · Measure the length of the White Ash's shadow on a nice sunny day. Place the end of your measuring tape at the base of the shadow. Record the length on your paper. · Next measure your shadow. Stand next to the White Ash and have

  15. Prolongation technologies for campaign life of tall oven

    SciTech Connect (OSTI)

    Doko, Yoshiji; Saji, Takafumi; Kitayama, Yoshiteru; Yoshida, Shuhei [Sumitomo Metal Industries, Ltd., Kashima, Ibaraki (Japan). Kashima Steel Works

    1997-12-31

    In Kashima Steel Works, 25-year-old 7-meter-high coke ovens have damage on their walls. However, by using new methods of internal in-situ investigation, ceramic welding for the extended central and upper portions of coke ovens has prolonged the campaign life for over 40 years without large-scale hot repair. In this paper, introduction of these new methods, its application in Kashima and the policy of repairing the tall coke oven are reported.

  16. Process for tertiary oil recovery using tall oil pitch

    DOE Patents [OSTI]

    Radke, Clayton J. (El Cerrito, CA)

    1985-01-01

    Compositions and process employing same for enhancing the recovery of residual acid crudes, particularly heavy crudes, by injecting a composition comprising caustic in an amount sufficient to maintain a pH of at least about 11, preferably at least about 13, and a small but effective amount of a multivalent cation for inhibiting alkaline silica dissolution with the reservoir. Preferably a tall oil pitch soap is included and particularly for the heavy crudes a polymeric mobility control agent.

  17. Growing Sweetclover in Texas. 

    E-Print Network [OSTI]

    Spears, Ben; Coffey, Lee; Trew, E. M.

    1957-01-01

    .nua,l yellow-flowered sweetclover, Meli- iotu.s indica, often called sour clover, seldom reaches a height of 3 feet while Hubam often is 6 feet tall. Melilotus indica matures very early, but the forage is not palatable to livestock and this clover should.... The object of this two-crop system is to obtain an extra crop from the land 8 and to keep down weeds in the young sweet- clover. Inoculation I A strain of bacteria lives on the roots of 1 legumes in clumps (nodules), and these bacteria take nitrogen...

  18. The role of the aerodynamic modifications of the shapes of tall buildings

    E-Print Network [OSTI]

    Lee, Jooeun, S.M. Massachusetts Institute of Technology

    2011-01-01

    With the advances in technology, recent tall building design has undergone a shift to the free-style geometric forms in the exuberant and liberal atmosphere. As a height of the building increases, it is more susceptible ...

  19. Collapse scenarios of WTC 1 & 2 with extension to generic tall buildings 

    E-Print Network [OSTI]

    Usmani, Asif; Flint, Graeme; Jowsey, Allan; Roben, Charlotte; Torero, Jose L

    This paper presents a summary of the author’s investigation into the collapse of tall buildings. A large number of computational analyses have been carried out at the University of Edinburgh (UoE) over the last 4 years ...

  20. Tall buildings in Asia : a critique on the high-rise building in Colombo, Shri Lanka

    E-Print Network [OSTI]

    Pieris, Anoma D. (Anoma Darshani)

    1993-01-01

    The recent generation of tall buildings in Asia have been appropriated from the West with little adaptation. With no understanding of the forces that have generated this building form, Asia embraces the high-rise as an ...

  1. Forty-Six-Foot Tall Needle Sculpture Rises Over Arts Quad > EMC2...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A 46-foot tall blue, needle-shaped sculpture. The structure - tilted "A Needle Woman: Galaxy was a Memory, Earth is a Souvenir" - is part of Cornell's Council for the Arts'...

  2. material removal

    National Nuclear Security Administration (NNSA)

    %2A en Nuclear Material Removal http:www.nnsa.energy.govaboutusourprogramsdnnm3remove

    Pag...

  3. FLUX MEASUREMENTS FROM A TALL TOWER IN A COMPLEX LANDSCAPE

    SciTech Connect (OSTI)

    Kurzeja, R.; Weber, A.; Chiswell, S.; Parker, M.

    2010-07-22

    The accuracy and representativeness of flux measurements from a tall tower in a complex landscape was assessed by examining the vertical and sector variability of the ratio of wind speed to momentum flux and the ratio of vertical advective to eddy flux of heat. The 30-60 m ratios were consistent with theoretical predictions which indicate well mixed flux footprints. Some variation with sector was observed that were consistent with upstream roughness. Vertical advection was negligible compared with vertical flux except for a few sectors at night. This implies minor influence from internal boundary layers. Flux accuracy is a function of sector and stability but 30-60 m fluxes were found to be generally representative of the surrounding landscape. This paper will study flux data from a 300 m tower, with 4 levels of instruments, in a complex landscape. The surrounding landscape will be characterized in terms of the variation in the ratio of mean wind speed to momentum flux as a function of height and wind direction. The importance of local advection will be assessed by comparing vertical advection with eddy fluxes for momentum and heat.

  4. What Really Grows Exports

    E-Print Network [OSTI]

    Myers, Lawrence C.

    What Really Grows Exports Bringing It All Back Home Should We Be Afraid of Accruals? Products of Their Environment a report on new research from the tuck school of business at dartmouth | fall 2014 Do exporters Competitiveness Diagnostic Toolkit," which was written to help developing nations increase their exports

  5. Mitigation, Adaptation, Uncertainty -- Growing Water

    E-Print Network [OSTI]

    Felsen, Martin; Dunn, Sarah

    2008-01-01

    Growing Water Martin Felsen andSarah Dunn The Growing Water project addresses a report fromin the world will face water shortages by 2025, a situation

  6. Growing Oats in Texas. 

    E-Print Network [OSTI]

    Atkins; I. M.; McDaniel, M. E.; Gardenhire, J. H.

    1969-01-01

    and more rapidly growing intermediate ?.inter-type varieties can be used in the northern !'art of Central and East Texas. Included in .his group are New Nortex, Norwin, Alamo-X, Qra. Moregrain and others. Less cold tolerant :.arieties and near..., Norwin, Bronco, Mustang, New Nortex, Ora, Alamo-X, Nora Spring seedin! Cimarron, Norwin, A Moregrain, Coronado, Corte7 do. Ora, Nora, New Nortex, Coronado, Cortez, Alaa Norwin, Alamo-X, Moregrain Moregrain IV 8, 9, 11 Ora, New Nortex, Moregrain...

  7. LEARNING DESIGN RULES FOR WIND BRACINGS IN TALL Tomasz Arciszewski1, Associate Member ASCE, Eric Bloedorn2

    E-Print Network [OSTI]

    Michalski, Ryszard S.

    study of learning design rules for wind bracings in tall buildings. Design rules are generated1 LEARNING DESIGN RULES FOR WIND BRACINGS IN TALL BUILDINGS Tomasz Arciszewski1, Associate Member for and generating problem-relevant attributes beyond those originally provided. The decision rules generated

  8. Internal hydraulic jumps and overturning generated by tidal flow over a tall steep ridge

    E-Print Network [OSTI]

    Klymak, Jody M.

    that tidal energy is both converted into internal waves, which radiate away from the topography, and used of tidal mixing for global climate models, the physical processes governing the transfer of energy fromInternal hydraulic jumps and overturning generated by tidal flow over a tall steep ridge Sonya Legg

  9. Aerodynamic Loads on Tall Buildings: Interactive Database Yin Zhou. M.ASCE1

    E-Print Network [OSTI]

    Kareem, Ahsan

    for possible inclusion as a design guide in the next generation of codes and standards. DOI: 10.1061/ ASCE 0733 tools in commercial design practice. However, considering the cost and lead time needed for wind tunnel.M.ASCE2 ; and Ahsan Kareem, M.ASCE3 Abstract: Under the action of wind, tall buildings oscillate

  10. Full-Scale Performance Evaluation of Tall Buildings Under Tracy Kijewski-Correaa

    E-Print Network [OSTI]

    Kareem, Ahsan

    zone effects in finite-element modeling of wind-sensitive structures. KEYWORDS: Dynamic Responses, Wind, the establishment of rooftop anemometry and a means to relate surface winds to gradient winds within the urban zoneFull-Scale Performance Evaluation of Tall Buildings Under Winds Tracy Kijewski-Correaa , J. David

  11. Seismic Intensity Estimation of Tall Buildings in Earthquake Early Warning System

    E-Print Network [OSTI]

    Greer, Julia R.

    prediction equation (GMPE) that predicts response spectral amplitude from knowledge of earthquake magnitudeSeismic Intensity Estimation of Tall Buildings in Earthquake Early Warning System M. H. Cheng & T. W. Graves U.S. Geological Survey, USA SUMMARY: In California, United States, an earthquake early

  12. Bioproducts and Biofuels – Growing Together!

    Broader source: Energy.gov [DOE]

    Breakout Session 2B—Integration of Supply Chains II: Bioproducts—Enabling Biofuels and Growing the Bioeconomy Bioproducts and Biofuels – Growing Together! Andrew Held, Senior Director, Deployment and Engineering, Virent, Inc.

  13. A contribution to urbanism--the tall building as a multi-dimensional framework for additive growth and change

    E-Print Network [OSTI]

    Nelson, David J. (David Jeffrey)

    1987-01-01

    Skyscrapers do not destroy cities; they make them look different and they make the urban space more crowded, but they have not yet put an end to the urban environment. Many of the problems with the early tall buildings ...

  14. Decrements in Children's Responses to Big and Tall: A Reconsideration of the Potential Cognitive and Semantic Causes

    E-Print Network [OSTI]

    Gathercole, V. C. Mueller

    1980-01-01

    The potential causes of decrements in children's understanding of big and tall (Maratsos, 1973, 1974) are reconsidered. Five hypotheses are examined in detail. Two of them, the strong cognitive hypothesis and the strong semantic hypothesis, offer...

  15. Growing and Storing Sweet Potatoes. 

    E-Print Network [OSTI]

    Potts, A. T.; Olsen, J. C.

    1916-01-01

    College o/Texas (in cooperation with the United States Department of Agriculture) AUGUST, 1916 EXTENSION SERVICE No. B. 27 Gro"lVing and Storing S"lVeet Potatoes Address CLARENCE OUSLEY Director and State Agent, College Station, Texas Growing alld Storing... of mixed potatoes seldom bring satisfactory prices. Each community should try to confine their planting to one, or, at the most, two varieties. If more than one variety is grown they mU:st be harvested, stored and marketed separately. The varieties to grow...

  16. Research Councils UK Growing with

    E-Print Network [OSTI]

    Crowther, Paul

    Research Councils UK Growing with agri-science #12;Research funded by the Research Councils makes of approaches to support innovation and deliver impact from research, including the development of collaborative research programmes, investment in major research capabilities, such as national research facilities

  17. Organization of growing random networks

    SciTech Connect (OSTI)

    Krapivsky, P. L.; Redner, S.

    2001-06-01

    The organizational development of growing random networks is investigated. These growing networks are built by adding nodes successively, and linking each to an earlier node of degree k with an attachment probability A{sub k}. When A{sub k} grows more slowly than linearly with k, the number of nodes with k links, N{sub k}(t), decays faster than a power law in k, while for A{sub k} growing faster than linearly in k, a single node emerges which connects to nearly all other nodes. When A{sub k} is asymptotically linear, N{sub k}(t){similar_to}tk{sup {minus}{nu}}, with {nu} dependent on details of the attachment probability, but in the range 2{lt}{nu}{lt}{infinity}. The combined age and degree distribution of nodes shows that old nodes typically have a large degree. There is also a significant correlation in the degrees of neighboring nodes, so that nodes of similar degree are more likely to be connected. The size distributions of the in and out components of the network with respect to a given node{emdash}namely, its {open_quotes}descendants{close_quotes} and {open_quotes}ancestors{close_quotes}{emdash}are also determined. The in component exhibits a robust s{sup {minus}2} power-law tail, where s is the component size. The out component has a typical size of order lnt, and it provides basic insights into the genealogy of the network.

  18. Forecast Technical Document Felling and Removals

    E-Print Network [OSTI]

    of local investment and business planning. Timber volume production will be estimated at sub. Planning of operations. Control of the growing stock. Wider reporting (under UKWAS). The calculation fellings and removals are handled in the 2011 Production Forecast system. Tom Jenkins Robert Matthews Ewan

  19. On carbon footprints and growing energy use

    E-Print Network [OSTI]

    Oldenburg, C.M.

    2012-01-01

    On carbon footprints and growing energy use Curtis M.reductions in the carbon footprint of a growing organizationhis own organization's carbon footprint and answers this

  20. Bioproducts and Biofuels - Growing Together! | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bioproducts and Biofuels - Growing Together Bioproducts and Biofuels - Growing Together Breakout Session 2B-Integration of Supply Chains II: Bioproducts-Enabling Biofuels and...

  1. Constraints on Carbon Monoxide Emissions Based on Tall Tower Measurements in the U.S. Upper Midwest

    E-Print Network [OSTI]

    Minnesota, University of

    Constraints on Carbon Monoxide Emissions Based on Tall Tower Measurements in the U.S. Upper Midwest-up emission estimates in response to top-down constraints. 1. INTRODUCTION Carbon monoxide (CO) is a precursor is emitted during the combustion of biomass and fossil fuel and produced photochemically from the oxidation

  2. Seasonal development of ozone-induced foliar injury on tall milkweed (Asclepias exaltata) in Great Smoky Mountains National Park

    E-Print Network [OSTI]

    Neufeld, Howard S.

    Seasonal development of ozone-induced foliar injury on tall milkweed (Asclepias exaltata) in Great by symptoms of foliar ozone injury. Abstract The goals of this study were to document the development of ozone-induced foliar injury, on a leaf-by-leaf basis, and to develop ozone exposure relationships for leaf cohorts

  3. GROW HOME | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergy A plug-inPPLforLDRD Report11, SolarMat 4" |a,- p^A CU ^ ^JL\ CC6p^ w bGROW HOME

  4. GROW HOME | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergy A plug-inPPLforLDRD Report11, SolarMat 4" |a,- p^A CU ^ ^JL\ CC6p^ w bGROW

  5. A high rise multi-use building for Boston : an investigation into the nature and organization of public space in a tall building

    E-Print Network [OSTI]

    Weiner, David Jay

    1984-01-01

    This thesis is essentially a study of how to organize public space vertically in a tall building. In most cases, high rise buildings tend to be organized in one of two ways, either centrally, with the core elements in the ...

  6. Ames Lab 101: Growing Crystals in Space

    SciTech Connect (OSTI)

    Trivedi, Rohit

    2011-01-01

    Rohit Trivedi, distinguished professor of materials science and engineering, discusses his research with NASA to grow crystals in space.

  7. Silicon crystal growing by oscillating crucible technique

    DOE Patents [OSTI]

    Schwuttke, G.H.; Kim, K.M.; Smetana, P.

    1983-08-03

    A process for growing silicon crystals from a molten melt comprising oscillating the container during crystal growth is disclosed.

  8. Ames Lab 101: Growing Crystals in Space

    ScienceCinema (OSTI)

    Trivedi, Rohit

    2012-08-29

    Rohit Trivedi, distinguished professor of materials science and engineering, discusses his research with NASA to grow crystals in space.

  9. Growing plants on atoll soils

    SciTech Connect (OSTI)

    Stone, E L; Migvar, L; Robison, W L

    2000-02-16

    Many years ago people living on atolls depended entirely on foods gathered from the sea and reefs and grown on land. Only a few plants, such as coconut (ni), Pandanus (bob), and arrowroot (mok-mok), could be grown on the lower rainfall atolls, although adequate groundwater conditions also allowed taro (iaraj, kotak, wot) to be cultivated. On higher rainfall atolls, breadfruit (ma) was a major food source, and banana (binana, kepran), lime (laim), and taros (iaraj, kotak, wot) could be grown. The early atoll populations were experts in growing plants that were vital to sustaining their nutrition requirements and to providing materials for thatch, basketry, cordage, canoe construction, flowers, and medicine. They knew which varieties of food plants grew well or poorly on their atolls, how to propagate them, and where on their atoll they grew best. They knew the uses of most native plants and what the various woods were well suited for. Many varieties of Pandanus (bob) and breadfruit (ma) grew well with high rainfall, but only a few produced well on drier atolls. Such information had been passed down through the generations although some of it has been lost in the last century. Today there are new plants and new varieties of existing plants that can be grown on atolls. There are also new materials and information on how to grow both the old and new plants more effectively. However, there are also introduced weeds and pests to control. Today, there is also an acute need to grow more of the useful plants adapted to atolls. Increasing numbers of people living on an atoll without an equal increase in income or food production stretches the available food supplies. Much has been written about the poor conditions for plant growth on atolls. As compared with many places in the world where crops are grown, however, atolls can provide some highly favorable conditions. For instance, the driving force for plant growth is sunlight, and on atolls light is abundant throughout the year. Except on the driest of atolls, air temperature and humidity range only within limits set by the surrounding sea. There are no cold seasons, no frosts, no cold soils, no dry winds, and no periodic plagues of insects or diseases moving from miles away. Problems of soil drainage or salinity are few and easily recognized. Nor are there problems with acid soils, soil crusting, or erosion that challenge cultivators in many other areas. On the contrary, some of the black soils at the center of wide islands rank with the best soils of Russia and the American Midwest, except for their shortage of potassium and the uncertainties of rainfall. Some of these atoll soils contain more total nitrogen than many of the world's most productive agricultural soils and, in some, the total phosphorus content is so high as to be almost unbelievable--two to five tons of the element per acre. Certainly, problems exist in growing plants on atolls. There are also some special concerns not encountered in other environments, such as the wind and salt spray near shore. The two major physical limitations, however, are inadequate rainfall in some years and in many places, and soil fertility limitations. The alkaline or ''limy'' make-up of atoll soils means that a few plant nutrients, especially iron, limit growth of many introduced plants, and this is difficult to correct. As elsewhere in the world, many--but not all--atoll soils lack enough nitrogen and/or phosphorus for high yield, and all lack sufficient potassium. There is no practical way of overcoming drought except by use of tolerant plants such as coconut (ni) and Pandanus (bob), plus collection and careful use of whatever water is available. There are opportunities to overcome nutritional limitations mentioned above, first, by intensive use of all organic debris and household wastes in small gardens and, second, by use of commercial fertilizers. Imported fertilizers are expensive, certainly, but much less so on a family basis than the equivalent costs of imported food.

  10. Graphitic packing removal tool

    DOE Patents [OSTI]

    Meyers, Kurt Edward (Avella, PA); Kolsun, George J. (Pittsburgh, PA)

    1997-01-01

    Graphitic packing removal tools for removal of the seal rings in one piece. he packing removal tool has a cylindrical base ring the same size as the packing ring with a surface finish, perforations, knurling or threads for adhesion to the seal ring. Elongated leg shanks are mounted axially along the circumferential center. A slit or slits permit insertion around shafts. A removal tool follower stabilizes the upper portion of the legs to allow a spanner wrench to be used for insertion and removal.

  11. Graphitic packing removal tool

    DOE Patents [OSTI]

    Meyers, K.E.; Kolsun, G.J.

    1997-11-11

    Graphitic packing removal tools for removal of the seal rings in one piece are disclosed. The packing removal tool has a cylindrical base ring the same size as the packing ring with a surface finish, perforations, knurling or threads for adhesion to the seal ring. Elongated leg shanks are mounted axially along the circumferential center. A slit or slits permit insertion around shafts. A removal tool follower stabilizes the upper portion of the legs to allow a spanner wrench to be used for insertion and removal. 5 figs.

  12. Continuous sulfur removal process

    DOE Patents [OSTI]

    Jalan, deceased, Vinod (late of Concord, MA); Ryu, Jae (Cambridge, MA)

    1994-01-01

    A continuous process for the removal of hydrogen sulfide from a gas stream using a membrane comprising a metal oxide deposited on a porous support is disclosed.

  13. Maine Company Growing with Weatherization Work

    Broader source: Energy.gov [DOE]

    Maine's BIOSAFE Environmental Services expands into weatherization, assisting low-income families with their services and creating jobs as business grows.

  14. One Direction: Researchers grow nanocircuitry with semiconducting...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    partners@anl.gov. One Direction: Researchers grow nanocircuitry with semiconducting graphene nanoribbons By Justin H.S. Breaux * October 13, 2015 Tweet EmailPrint In a...

  15. Riparian Forest Grows Trees fall in

    E-Print Network [OSTI]

    Riparian Forest Grows Trees Die Trees fall in the lake Trees leave the littoral zone "Life" Cycle of Coarse Woody Habitat #12;Riparian Forest Grows What factors drive the species composition and stand factors drive the species composition and stand structure? Trees Die Trees fall in the lake Trees leave

  16. Microalgae Cultivation using Offshore Membrane Enclosures for Growing Algae (OMEGA)

    E-Print Network [OSTI]

    Wiley, Patrick Edward

    2013-01-01

    enclosures for growing algae (OMEGA). J. Sustainableenclosures for growing algae (OMEGA). Bioresour. Technol.enclosures for growing algae (OMEGA). Journal of Sustainable

  17. Reactor for removing ammonia

    DOE Patents [OSTI]

    Luo, Weifang (Livermore, CA); Stewart, Kenneth D. (Valley Springs, CA)

    2009-11-17

    Disclosed is a device for removing trace amounts of ammonia from a stream of gas, particularly hydrogen gas, prepared by a reformation apparatus. The apparatus is used to prevent PEM "poisoning" in a fuel cell receiving the incoming hydrogen stream.

  18. Continuous sulfur removal process

    DOE Patents [OSTI]

    Jalan, V.; Ryu, J.

    1994-04-26

    A continuous process for the removal of hydrogen sulfide from a gas stream using a membrane comprising a metal oxide deposited on a porous support is disclosed. 4 figures.

  19. What Makes Clouds Grow and Die?

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    fairly well." Based on these results, Hagos and his collaborators will next focus on cold pools and their role in growing small shallow clouds into large, deep ones. The team...

  20. Social disruption caused by tobacco growing

    E-Print Network [OSTI]

    Marty Otanez

    2008-01-01

    suffocating. The smell and the poison grow in your mouth.of the question going near that poison [tobacco pesticides].doesn’t let me do the poison now because of what happened

  1. Orthopedic Correction of Growing Retrognathic Hyperdivergent Patients 

    E-Print Network [OSTI]

    Carrillo, Roberto

    2014-05-13

    The purpose of this prospective study was to determine whether dental intrusion is effective in treating growing retrognathic hyperdivergent patients without negatively affecting the roots and periodontal structures. The ...

  2. Quantifying the Effects of Removing Permissions from Android Applications

    E-Print Network [OSTI]

    Chen, Hao

    Quantifying the Effects of Removing Permissions from Android Applications Kristen Kennedy, Eric Gustafson, Hao Chen University of California, Davis Abstract With the growing popularity of Android smart study found that approximately 26% of Android applications in Google Play can access personal data

  3. Atmospheric Stability Impacts on Power Curves of Tall Wind Turbines - An Analysis of a West Coast North American Wind Farm

    SciTech Connect (OSTI)

    Wharton, S; Lundquist, J K

    2010-02-22

    Tall wind turbines, with hub heights at 80 m or above, can extract large amounts of energy from the atmosphere because they are likely to encounter higher wind speeds, but they face challenges given the complex nature of wind flow and turbulence at these heights in the boundary layer. Depending on whether the boundary layer is stable, neutral, or convective, the mean wind speed, direction, and turbulence properties may vary greatly across the tall turbine swept area (40 to 120 m AGL). This variability can cause tall turbines to produce difference amounts of power during time periods with identical hub height wind speeds. Using meteorological and power generation data from a West Coast North American wind farm over a one-year period, our study synthesizes standard wind park observations, such as wind speed from turbine nacelles and sparse meteorological tower observations, with high-resolution profiles of wind speed and turbulence from a remote sensing platform, to quantify the impact of atmospheric stability on power output. We first compare approaches to defining atmospheric stability. The standard, limited, wind farm operations enable the calculation only of a wind shear exponent ({alpha}) or turbulence intensity (I{sub U}) from cup anemometers, while the presence at this wind farm of a SODAR enables the direct observation of turbulent kinetic energy (TKE) throughout the turbine rotor disk. Additionally, a nearby research meteorological station provided observations of the Obukhov length, L, a direct measure of atmospheric stability. In general, the stability parameters {alpha}, I{sub U}, and TKE are in high agreement with the more physically-robust L, with TKE exhibiting the best agreement with L. Using these metrics, data periods are segregated by stability class to investigate power performance dependencies. Power output at this wind farm is highly correlated with atmospheric stability during the spring and summer months, while atmospheric stability exerts little impact on power output during the winter and autumn periods. During the spring and summer seasons, power output for a given wind speed was significantly higher during stable conditions and significantly lower during strongly convective conditions: power output differences approached 20% between stable and convective regimes. The dependency of stability on power output was apparent only when both turbulence and the shape of the wind speed profile were considered. Turbulence is one of the mechanisms by which atmospheric stability affects a turbine's power curve at this particular site, and measurements of turbulence can yield actionable insights into wind turbine behavior.

  4. Arsenic removal from water

    DOE Patents [OSTI]

    Moore, Robert C. (Edgewood, NM); Anderson, D. Richard (Albuquerque, NM)

    2007-07-24

    Methods for removing arsenic from water by addition of inexpensive and commonly available magnesium oxide, magnesium hydroxide, calcium oxide, or calcium hydroxide to the water. The hydroxide has a strong chemical affinity for arsenic and rapidly adsorbs arsenic, even in the presence of carbonate in the water. Simple and commercially available mechanical methods for removal of magnesium hydroxide particles with adsorbed arsenic from drinking water can be used, including filtration, dissolved air flotation, vortex separation, or centrifugal separation. A method for continuous removal of arsenic from water is provided. Also provided is a method for concentrating arsenic in a water sample to facilitate quantification of arsenic, by means of magnesium or calcium hydroxide adsorption.

  5. Removable feedwater sparger assembly

    DOE Patents [OSTI]

    Challberg, R.C.

    1994-10-04

    A removable feedwater sparger assembly includes a sparger having an inlet pipe disposed in flow communication with the outlet end of a supply pipe. A tubular coupling includes an annular band fixedly joined to the sparger inlet pipe and a plurality of fingers extending from the band which are removably joined to a retention flange extending from the supply pipe for maintaining the sparger inlet pipe in flow communication with the supply pipe. The fingers are elastically deflectable for allowing engagement of the sparger inlet pipe with the supply pipe and for disengagement therewith. 8 figs.

  6. Drum lid removal tool

    DOE Patents [OSTI]

    Pella, Bernard M. (Martinez, GA); Smith, Philip D. (North Augusta, SC)

    2010-08-24

    A tool for removing the lid of a metal drum wherein the lid is clamped over the drum rim without protruding edges, the tool having an elongated handle with a blade carried by an angularly positioned holder affixed to the midsection of the handle, the blade being of selected width to slice between lid lip and the drum rim and, when the blade is so positioned, upward motion of the blade handle will cause the blade to pry the lip from the rim and allow the lid to be removed.

  7. Condensate removal device

    DOE Patents [OSTI]

    Maddox, James W. (Newport News, VA); Berger, David D. (Alexandria, VA)

    1984-01-01

    A condensate removal device is disclosed which incorporates a strainer in unit with an orifice. The strainer is cylindrical with its longitudinal axis transverse to that of the vapor conduit in which it is mounted. The orifice is positioned inside the strainer proximate the end which is remoter from the vapor conduit.

  8. Growing Potatoes in Your Home Garden

    E-Print Network [OSTI]

    Douches, David S.

    home garden? *Growing potatoes produces a bountiful harvest....depending on which variety your choose. In general, 1 inch of water per week, from rainfall or irrigation, is needed on well drained soil. When to plant potatoes: * Plant seed pieces in spring when the soil temp. is 45F or above. When to harvest

  9. Energy risk in Latin America:Energy risk in Latin America: the growing challengesthe growing challenges

    E-Print Network [OSTI]

    Dixon, Juan

    resources -economic reforms opened space for private investment in energy -development of an infrastructureEnergy risk in Latin America:Energy risk in Latin America: the growing challengesthe growing Conference on Energy Trading and Risk Management 21 - 22 November 2005, City University, London

  10. Energy & Water:Energy & Water: A Growing and IncreasinglyA Growing and Increasingly

    E-Print Network [OSTI]

    Keller, Arturo A.

    #12;20 Treatment TechnologiesTreatment Technologies #12;21 21 #12;22 Skinner PlantSkinner Plant Solar1 Energy & Water:Energy & Water: A Growing and IncreasinglyA Growing and Increasingly Important of Southern California First Western Forum on Energy & Water Sustainability #12;2 "Water is for life, power

  11. Pneumatic soil removal tool

    DOE Patents [OSTI]

    Neuhaus, John E. (Newport News, VA)

    1992-01-01

    A soil removal tool is provided for removing radioactive soil, rock and other debris from the bottom of an excavation, while permitting the operator to be located outside of a containment for that excavation. The tool includes a fixed jaw, secured to one end of an elongate pipe, which cooperates with a movable jaw pivotably mounted on the pipe. Movement of the movable jaw is controlled by a pneumatic cylinder mounted on the pipe. The actuator rod of the pneumatic cylinder is connected to a collar which is slidably mounted on the pipe and forms part of the pivotable mounting assembly for the movable jaw. Air is supplied to the pneumatic cylinder through a handle connected to the pipe, under the control of an actuator valve mounted on the handle, to provide movement of the movable jaw.

  12. Pneumatic soil removal tool

    DOE Patents [OSTI]

    Neuhaus, J.E.

    1992-10-13

    A soil removal tool is provided for removing radioactive soil, rock and other debris from the bottom of an excavation, while permitting the operator to be located outside of a containment for that excavation. The tool includes a fixed jaw, secured to one end of an elongate pipe, which cooperates with a movable jaw pivotably mounted on the pipe. Movement of the movable jaw is controlled by a pneumatic cylinder mounted on the pipe. The actuator rod of the pneumatic cylinder is connected to a collar which is slidably mounted on the pipe and forms part of the pivotable mounting assembly for the movable jaw. Air is supplied to the pneumatic cylinder through a handle connected to the pipe, under the control of an actuator valve mounted on the handle, to provide movement of the movable jaw. 3 figs.

  13. Quick Stain Removal Guide 

    E-Print Network [OSTI]

    Brown, Pamela J.

    1998-07-29

    and dryer. ? Use the hottest wash temperature recommended on the garment care label. ? Use the right wash and dry cycle for the fabric. ? Avoid using chlorine bleach on silk, wool or spandex or on non-colorfast garments. ? Remove clothes... color-safe bleach or fabric softener. Bleaches are strong cleaning agents. Follow the in- structions on the containers. Use chlorine bleach on colorfast fabrics; it is most effective if added 5 to 6 minutes into the wash cycle. It is best...

  14. UNIVERSITY OF CALGARY Modeling Fracture Formation on Growing Surfaces

    E-Print Network [OSTI]

    Prusinkiewicz, Przemyslaw

    UNIVERSITY OF CALGARY Modeling Fracture Formation on Growing Surfaces by Pavol Federl A THESIS Fracture Formation on Growing Surfaces" submitted by Pavol Federl in partial fulfillment This thesis describes a framework for modeling fracture formation on differentially growing, bi- layered

  15. About the Bioenergy Technologies Office: Growing America's Energy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    You are here Home About the Bioenergy Technologies Office: Growing America's Energy Future About the Bioenergy Technologies Office: Growing America's Energy Future The U.S....

  16. Mass freezing in growing neutrino quintessence

    E-Print Network [OSTI]

    Nelson J. Nunes; Lily Schrempp; Christof Wetterich

    2011-05-31

    Growing neutrino quintessence solves the coincidence problem for dark energy by a growing cosmological value of the neutrino mass which emerges from a cosmon-neutrino interaction stronger than gravity. The cosmon-mediated attraction between neutrinos induces the formation of large scale neutrino lumps in a recent cosmological epoch. We argue that the non-linearities in the cosmon field equations stop the further increase of the neutrino mass within sufficiently dense and large lumps. As a result, we find the neutrino induced gravitational potential to be substantially reduced when compared to linear extrapolations. We furthermore demonstrate that inside a lump the possible time variation of fundamental constants is much smaller than their cosmological evolution. This feature may reconcile current geophysical bounds with claimed cosmological variations of the fine structure constant.

  17. Growing America's Energy Future | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels Data CenterFinancial OpportunitiesDepartment of EnergyGrowing America's

  18. Electrochemically assisted paint removal

    SciTech Connect (OSTI)

    Keller, R.; Hydock, D.M.; Burleigh, T.D.

    1995-12-31

    A method to remove paint coatings from metal and other electronically conductive substrates is being studied. In particular, the remediation of objects coated with lead based paints is the focus of research. The approach also works very well with automotive coatings and may be competitive with sandblasting. To achieve debonding of the coating, the deteriorated or artifically damaged surface of the object is cathodically polarized. The object can be immersed in a benign aqueous electrolyte for treatment, or the electrolyte can be retained in an absorbent pad covering the surface to be treated.

  19. GROW, EXPORT, ATTRACT, SUPPORT Universities' contribution to Scotland's economic growth

    E-Print Network [OSTI]

    Edinburgh, University of

    GROW, EXPORT, ATTRACT, SUPPORT Universities' contribution to Scotland's economic growth #12;Contents Summary Grow 3 Export 5 Attract 10 Support 21 #12;Universities are recognised throughout the world to grow the GVA it contributes to Scotland. Universities have a growing export role, with international

  20. Chemical composition, microstructure, and hygroscopic properties of aerosol particles at the Zotino Tall Tower Observatory (ZOTTO), Siberia, during a summer campaign

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mikhailov, E. F.; Mironov, G. N.; Pöhlker, C.; Chi, X.; Krüger, M. L.; Shiraiwa, M.; Förster, J. -D.; Pöschl, U.; Vlasenko, S. S.; Ryshkevich, T. I.; et al

    2015-03-16

    In this study we describe the hygroscopic properties of accumulation- and coarse-mode aerosol particles sampled at the Zotino Tall Tower Observatory (ZOTTO) in Central Siberia (61° N; 89° E) from 16 to 21 June 2013. The hygroscopic growth measurements were supplemented with chemical analyses of the samples, including inorganic ions and organic/elemental carbon. In addition, the microstructure and chemical composition of aerosol particles were analyzed by X-ray micro-spectroscopy (STXM-NEXAFS) and transmission electron microscopy (TEM). A mass closure analysis indicates that organic carbon accounted for 61 and 38% of PM in the accumulation mode and coarse mode, respectively. The water solublemore »fraction of organic matter was estimated to be 52 and 8% of PM in these modes. Sulfate, predominantly in the form of ammoniated sulfate, was the dominant inorganic component in both size modes: ~ 34% in the accumulation vs. ~ 47% in the coarse mode. The hygroscopic growth measurements were conducted with a filter-based differential hygroscopicity analyzer (FDHA) over the range of 5–99.4% RH in the hydration and dehydration operation modes. The FDHA study indicates that both accumulation and coarse modes exhibit pronounced water uptake approximately at the same RH, starting at ~ 70%, while efflorescence occurred at different humidities, i.e., at ~ 35% RH for submicron particles vs. ~ 50% RH for supermicron particles. This ~ 15% RH difference was attributed to higher content of organic material in the submicron particles, which suppresses water release in the dehydration experiments. The kappa mass interaction model (KIM) was applied to characterize and parameterize non-ideal solution behavior and concentration-dependent water uptake by atmospheric aerosol samples in the 5–99.4% RH range. Based on KIM, the volume-based hygroscopicity parameter, ?v, was calculated. The ?v, ws value related to the water soluble (ws) fraction was estimated to be ~ 0.15 for the accumulation mode and ~ 0.36 for the coarse mode, respectively. The obtained ?v, ws for the accumulation mode is in good agreement with earlier data reported for remote sites in the Amazon rain forest (?v ≈ 0.15) and a Colorado boreal forest (?v ≈ 0.16). We used the Zdanovskii–Stokes–Robinson (ZSR) mixing rule to predict the chemical composition dependent hygroscopicity, ?v, p. The obtained ?v, p values overestimate the experimental FDHA-KIM-derived ?v, ws by factors of 1.8 and 1.5 for the accumulation and coarse modes, respectively. This divergence can be partly explained by incomplete dissolution of the hygroscopic inorganic compounds resulting from kinetic limitations due to a sparingly soluble organic coating. The TEM and STXM-NEXAFS results indicate that aged submicron (>300 nm) and supermicron aerosol particles possess core-shell structures with an inorganic core, and are enriched in organic carbon at the mixed particle surface. The direct FDHA kinetic studies provide a bulk diffusion coefficient of water of ~ 10?12 cm2 s?1 indicating a semi-solid state of the organic-rich phase leading to kinetic limitations of water uptake and release during hydration and dehydration cycles. Overall the present ZOTTO data set, obtained in the growing season, has revealed a strong influence of organic carbon on the hygroscopic properties of the ambient aerosols. The sparingly soluble organic coating controls hygroscopic growth, phase transitions, and microstructural rearrangement processes. The observed kinetic limitations can strongly influence the outcome of experiments performed on multi-second time scales, such as the commonly applied HTDMA (Hygroscopicity Tandem Differential Mobility Analyzer) and CCNC (Cloud Condensation Nuclei Counter) measurements.« less

  1. Method for removal of metal atoms from aqueous solution using suspended plant cells

    DOE Patents [OSTI]

    Jackson, Paul J. (Los Alamos, NM); Torres, deceased, Agapito P. (late of Los Alamos, NM); Delhaize, Emmanuel (Kaleen, AU)

    1992-01-01

    The use of plant suspension cultures to remove ionic metallic species and TNT-based explosives and their oxidation products from aqueous solution is described. Several plant strains were investigated including D. innoxia, Citrus citrus, and Black Mexican Sweet Corn. All showed significant ability to remove metal ions. Ions removed to sub-ppm levels include barium, iron, and plutonium. D. innoxia cells growing in media containing weapons effluent contaminated with Ba.sup.2+ also remove TNT, other explosives and oxidation products thereof from solution. The use of dead, dehydrated cells were also found to be of use in treating waste directly.

  2. Method for removal of explosives from aqueous solution using suspended plant cells

    DOE Patents [OSTI]

    Jackson, Paul J. (Los Alamos, NM); Torres, deceased, Agapito P. (late of Los Alamos, NM); Delhaize, Emmanuel (Giralang, AU)

    1994-01-01

    The use of plant suspension cultures to remove ionic metallic species and TNT-based explosives and their oxidation products from aqueous solution is described. Several plant strains were investigated including D. innoxia, Citrus citrus, and Black Mexican Sweet Corn. All showed significant ability to remove metal ions. Ions removed to sub-ppm levels include barium, iron, and plutonium. D. innoxia cells growing in media containing weapons effluent contaminated with Ba.sup.2+ also remove TNT, other explosives and oxidation products thereof from solution. The use of dead, dehydrated cells was also found to be of use in treating waste directly.

  3. Selective sweeps in growing microbial colonies

    E-Print Network [OSTI]

    Korolev, Kirill S; Karahan, Nilay; Murray, Andrew W; Hallatschek, Oskar; Nelson, David R; 10.1088/1478-3975/9/2/026008

    2012-01-01

    Evolutionary experiments with microbes are a powerful tool to study mutations and natural selection. These experiments, however, are often limited to the well-mixed environments of a test tube or a chemostat. Since spatial organization can significantly affect evolutionary dynamics, the need is growing for evolutionary experiments in spatially structured environments. The surface of a Petri dish provides such an environment, but a more detailed understanding of microbial growth on Petri dishes is necessary to interpret such experiments. We formulate a simple deterministic reaction-diffusion model, which successfully predicts the spatial patterns created by two competing species during colony expansion. We also derive the shape of these patterns analytically without relying on microscopic details of the model. In particular, we find that the relative fitness of two microbial strains can be estimated from the logarithmic spirals created by selective sweeps. The theory is tested with strains of the budding yeast...

  4. Fast-growing willow shrub named `Canastota`

    DOE Patents [OSTI]

    Abrahamson, Lawrence P.; Kopp, Richard F.; Smart, Lawrence B.; Volk, Timothy A.

    2007-05-15

    A distinct male cultivar of Salix sachalinensis.times.S. miyabeana named `Canastota`, characterized by rapid stem growth producing greater than 2.7-fold more woody biomass than its female parent (Salix sachalinensis `SX61`), 28% greater woody biomass yield than its male parent (Salix miyabeana `SX64`), and 20% greater woody biomass yield than a standard production cultivar, Salix dasyclados `SV1` when grown in the same field for the same length of time (two growing seasons after coppice) in Tully, N.Y. `Canastota` can be planted from dormant stem cuttings, produces multiple stems after coppice, and the stem biomass can be harvested when the plant is dormant. In the spring following harvest, the plant will re-sprout very vigorously, producing new stems that can be harvested after two to four years of growth. This harvest cycle can be repeated several times. `Canastota` displays a low incidence of rust disease or damage by willow sawfly.

  5. Removing Arsenic from Drinking Water

    ScienceCinema (OSTI)

    None

    2013-05-28

    See how INL scientists are using nanotechnology to remove arsenic from drinking water. For more INL research, visit http://www.facebook.com/idahonationallaboratory

  6. Removing Arsenic from Drinking Water

    SciTech Connect (OSTI)

    2011-01-01

    See how INL scientists are using nanotechnology to remove arsenic from drinking water. For more INL research, visit http://www.facebook.com/idahonationallaboratory

  7. The Growing Web of Open Data | Department of Energy

    Energy Savers [EERE]

    The Growing Web of Open Data The Growing Web of Open Data September 26, 2012 - 10:57am Addthis NREL's Visual API Browser presents energy data APIs as a web of key words. NREL's...

  8. Solar Ready Vets: Preparing Our Veterans to Join the Growing...

    Office of Environmental Management (EM)

    Solar Ready Vets: Preparing Our Veterans to Join the Growing Solar Workforce Solar Ready Vets: Preparing Our Veterans to Join the Growing Solar Workforce April 6, 2015 - 2:27pm...

  9. Fact #816: February 10, 2014 Natural Gas Refueling Stations Grow...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    6: February 10, 2014 Natural Gas Refueling Stations Grow Over the Last Ten Years Fact 816: February 10, 2014 Natural Gas Refueling Stations Grow Over the Last Ten Years In 2003...

  10. Turkey opens electricity markets as demand grows

    SciTech Connect (OSTI)

    McKeigue, J.; Da Cunha, A.; Severino, D. [Global Business Reports (United States)

    2009-06-15

    Turkey's growing power market has attracted investors and project developers for over a decade, yet their plans have been dashed by unexpected political or financial crises or, worse, obstructed by a lengthy bureaucratic approval process. Now, with a more transparent retail electricity market, government regulators and investors are bullish on Turkey. Is Turkey ready to turn the power on? This report closely examine Turkey's plans to create a power infrastructure capable of providing the reliable electricity supplies necessary for sustained economic growth. It was compiled with on-the-ground research and extensive interview with key industrial and political figures. Today, hard coal and lignite account for 21% of Turkey's electricity generation and gas-fired plants account for 50%. The Alfin Elbistan-B lignite-fired plant has attracted criticism for its lack of desulfurization units and ash dam facilities that have tarnished the industry's image. A 1,100 MW hard-coal fired plant using supercritical technology is under construction. 9 figs., 1 tab.

  11. Microalgae Cultivation using Offshore Membrane Enclosures for Growing Algae (OMEGA)

    E-Print Network [OSTI]

    Wiley, Patrick Edward

    2013-01-01

    G. Schaub, Microalgae and terrestrial biomass as source forBiomass collected in the settling chamber is removed, whereas suspended microalgaeBiomass collected in the settling chamber is removed, whereas suspended microalgae

  12. On carbon footprints and growing energy use

    SciTech Connect (OSTI)

    Oldenburg, C.M.

    2011-06-01

    Could fractional reductions in the carbon footprint of a growing organization lead to a corresponding real reduction in atmospheric CO{sub 2} emissions in the next ten years? Curtis M. Oldenburg, head of the Geologic Carbon Sequestration Program of LBNL’s Earth Sciences Division, considers his own organization's carbon footprint and answers this critical question? In addressing the problem of energy-related greenhouse gas (GHG) emissions and climate change, it is essential that we understand which activities are producing GHGs and the scale of emission for each activity, so that reduction efforts can be efficiently targeted. The GHG emissions to the atmosphere of an individual or group are referred to as the ‘carbon footprint’. This terminology is entirely appropriate, because 85% of the global marketed energy supply comes from carbon-rich fossil fuel sources whose combustion produces CO{sub 2}, the main GHG causing global climate change. Furthermore, the direct relation between CO2 emissions and fossil fuels as they are used today makes energy consumption a useful proxy for carbon footprint. It would seem to be a simple matter to reduce energy consumption across the board, both individually and collectively, to help reduce our carbon footprints and therefore solve the energyclimate crisis. But just how much can we reduce carbon footprints when broader forces, such as growth in energy use, cause the total footprint to simultaneously expand? In this feature, I present a calculation of the carbon footprint of the Earth Sciences Division (ESD), the division in which I work at Lawrence Berkeley National Laboratory (LBNL), and discuss the potential for reducing this carbon footprint. It will be apparent that in terms of potential future carbon footprint reductions under projections of expected growth, ESD may be thought of as a microcosm of the situation of the world as a whole, in which alternatives to the business-as-usual use of fossil fuels are needed if absolute GHG emission reductions are to be achieved.

  13. Multipollutant Removal with WOWClean® System 

    E-Print Network [OSTI]

    Romero, M.

    2010-01-01

    from the flue gas of a power plant and demonstrate the technology. The system integrates proven emission reduction techniques into a single, multi-pollutant reduction system and is designed to remove Mercury, SOx, NOx, particulates, heavy metals...

  14. FOA aimed at growing expansive database of Renewable Energy and...

    Open Energy Info (EERE)

    FOA aimed at growing expansive database of Renewable Energy and Energy Efficiency Incentives and Policies Home > Groups > Utility Rate Graham7781's picture Submitted by...

  15. Growing Up in Scotland: Food and Activity - Summary Report 

    E-Print Network [OSTI]

    Government, Scottish

    2009-03-18

    This report uses data from the Growing Up in Scotland study to explore issues related to, food and activity in Scotland specifically in relation to young children.

  16. Protection #2: Trap and Remove Sediment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Trap and Remove Sediment Protection 2: Trap and Remove Sediment The 3 Protections Defense in Depth August 1, 2013 Sediment behind LA Canyon weir is sampled and excavated...

  17. Removal - An alternative to clearance

    SciTech Connect (OSTI)

    Feinhals, J.; Kelch, A.; Kunze, V.

    2007-07-01

    This presentation shows the differences between the application of clearance and removal, both being procedures for materials leaving radiation protection areas permanently. The differentiation will be done on the basis of the German legislation but may be also applicable for other national legislation. For clearance in Germany two basic requirements must be given, i.e. that the materials are activated or contaminated and that they result from the licensed use or can be assigned to the scope of the license. Clearance needs not to be applied to objects in Germany which are to be removed only temporarily from controlled areas with the purpose of repair or reuse in other controlled areas. In these cases only the requirements of contamination control apply. In the case of removal it must either be proved by measurements that the relevant materials are neither activated nor contaminated or that the materials result from areas where activation or contamination is impossible due to the operational history considering operational procedures and events. If the material is considered neither activated nor contaminated there is no need for a clearance procedure. Therefore, these materials can be removed from radiation protection areas and the removal is in the responsibility of the licensee. Nevertheless, the removal procedure and the measuring techniques to be applied for the different types of materials need an agreement from the competent authority. In Germany a maximum value of 10% of the clearance values has been established in different licenses as a criterion for the application of removal. As approximately 2/3 of the total mass of a nuclear power plant is not expected to be contaminated or activated there is a need for such a procedure of removal for this non contaminated material without any regulatory control especially in the case of decommissioning. A remarkable example is NPP Stade where in the last three years more than 8600 Mg were disposed of by removal and only 315 Mg were released by clearance, even before the decommissioning licensing procedure was finished. (authors)

  18. Use of microalgae to remove pollutants from power plant discharges

    DOE Patents [OSTI]

    Wilde, Edward W. (1833 Pisgah Rd., North Augusta, SC 29841); Benemann, John R. (2741 O'Harte, San Pablo, CA 94806); Weissman, Joseph C. (2086 N. Porpoise Pt. La., Vero Beach, FL 32963); Tillett, David M. (911-3 Coquina La., Vero Beach, FL 32963)

    1991-01-01

    A method and system for removing pollutants dissolved in the aqueous discharge of a plant, such as a power plant, from a body of water having known hydraulogy and physicochemical characteristics, the method comprising (a) modifying the hydraulic system of the body of water including use of physical barriers to define a zone in a portion of the body of water which zone includes the discharge point and where the water has a range of physicochemical characteristics; (b) selecting a large and preferably filamentous, planktonically growing strain of algae adapted to absorb the particular pollutants and genetically dominating algae at the physicochemical characteristics of the zone; (c) establishing a colony of the selected algal strain in the zone; (d) harvesting a portion of the colony; and (e) reinnoculating the zone near the discharge point with a fraction of the harvested portion. The fraction used for reinnoculation can be adjusted to balance the rate of pollutant removal to the rate of pollutant discharge.

  19. Large Component Removal/Disposal

    SciTech Connect (OSTI)

    Wheeler, D. M.

    2002-02-27

    This paper describes the removal and disposal of the large components from Maine Yankee Atomic Power Plant. The large components discussed include the three steam generators, pressurizer, and reactor pressure vessel. Two separate Exemption Requests, which included radiological characterizations, shielding evaluations, structural evaluations and transportation plans, were prepared and issued to the DOT for approval to ship these components; the first was for the three steam generators and one pressurizer, the second was for the reactor pressure vessel. Both Exemption Requests were submitted to the DOT in November 1999. The DOT approved the Exemption Requests in May and July of 2000, respectively. The steam generators and pressurizer have been removed from Maine Yankee and shipped to the processing facility. They were removed from Maine Yankee's Containment Building, loaded onto specially designed skid assemblies, transported onto two separate barges, tied down to the barges, th en shipped 2750 miles to Memphis, Tennessee for processing. The Reactor Pressure Vessel Removal Project is currently under way and scheduled to be completed by Fall of 2002. The planning, preparation and removal of these large components has required extensive efforts in planning and implementation on the part of all parties involved.

  20. Actinide removal from spent salts

    DOE Patents [OSTI]

    Hsu, Peter C. (Pleasanton, CA); von Holtz, Erica H. (Livermore, CA); Hipple, David L. (Livermore, CA); Summers, Leslie J. (Livermore, CA); Adamson, Martyn G. (Danville, CA)

    2002-01-01

    A method for removing actinide contaminants (uranium and thorium) from the spent salt of a molten salt oxidation (MSO) reactor is described. Spent salt is removed from the reactor and analyzed to determine the contaminants present and the carbonate concentration. The salt is dissolved in water, and one or more reagents are added to precipitate the thorium as thorium oxide and/or the uranium as either uranium oxide or as a diuranate salt. The precipitated materials are filtered, dried and packaged for disposal as radioactive waste. About 90% of the thorium and/or uranium present is removed by filtration. After filtration, salt solutions having a carbonate concentration >20% can be dried and returned to the reactor for re-use. Salt solutions containing a carbonate concentration <20% require further clean-up using an ion exchange column, which yields salt solutions that contain less than 0.1 ppm of thorium or uranium.

  1. UNIVERSITY OF SUSSEX Removal expenses

    E-Print Network [OSTI]

    Sussex, University of

    scale: first year of employment: 100% second year of employment: 50% third year of employment: 25 be payable to staff whose contract is for one year or more. However, new staff employed on a contract of less than one year who contract is subsequently extended beyond one year will then be eligible for removal

  2. Irrigation Resources to Grow Biofuel:Irrigation Resources to Grow Biofuel: A National Overview with Role of

    E-Print Network [OSTI]

    Scott, Christopher

    1 Irrigation Resources to Grow Biofuel:Irrigation Resources to Grow Biofuel: A National Overview about the water and land potentially used forabout the water and land potentially used for biofuel Dry Beans Other small Wheat Barley Pasture Other Crops Other Hay Potatoes Veggies Silage corn Berries

  3. Industrial lead paint removal specifications

    SciTech Connect (OSTI)

    Stone, R.C.

    1997-06-01

    The purpose of this paper is to inform the reader as to some of the pertinent rules and regulations promulgated by the Environmental Protection Agency (EPA) and the Occupational Safety and Health Administration (OSHA) that may effect an industrial lead paint removal project. The paper discusses a recommended schedule of procedures and preparations to be followed by the lead paint removal specification writer when analyzing the possible impact of the project on the environment, the public and workers. Implications of the Clean Air Act, the Clean Water Act and the Resource Conservation and Recovery Act (RCRA) along with hazardous waste handling, manifesting, transporting and disposal procedures are discussed with special emphasis placed as to their impact on the writer and the facility owner. As the rules and regulations are highly complex, the writer has attempted to explain the methodology currently being used in state-of-the-art industrial lead abatement specifications.

  4. Removal of the Plutonium Recycle Test Reactor - 13031

    SciTech Connect (OSTI)

    Herzog, C. Brad [CH2M HILL, Inc. (United States)] [CH2M HILL, Inc. (United States); Guercia, Rudolph [US-DOE (United States)] [US-DOE (United States); LaCome, Matt [Meier Engineering Inc (United States)] [Meier Engineering Inc (United States)

    2013-07-01

    The 309 Facility housed the Plutonium Recycle Test Reactor (PRTR), an operating test reactor in the 300 Area at Hanford, Washington. The reactor first went critical in 1960 and was originally used for experiments under the Hanford Site Plutonium Fuels Utilization Program. The facility was decontaminated and decommissioned in 1988-1989, and the facility was deactivated in 1994. The 309 facility was added to Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) response actions as established in an Interim Record of Decision (IROD) and Action Memorandum (AM). The IROD directs a remedial action for the 309 facility, associated waste sites, associated underground piping and contaminated soils resulting from past unplanned releases. The AM directs a removal action through physical demolition of the facility, including removal of the reactor. Both CERCLA actions are implemented in accordance with U.S. EPA approved Remedial Action Work Plan, and the Remedial Design Report / Remedial Action Report associated with the Hanford 300-FF-2 Operable Unit. The selected method for remedy was to conventionally demolish above grade structures including the easily distinguished containment vessel dome, remove the PRTR and a minimum of 300 mm (12 in) of shielding as a single 560 Ton unit, and conventionally demolish the below grade structure. Initial sample core drilling in the Bio-Shield for radiological surveys showed evidence that the Bio-Shield was of sound structure. Core drills for the separation process of the PRTR from the 309 structure began at the deck level and revealed substantial thermal degradation of at least the top 1.2 m (4LF) of Bio-Shield structure. The degraded structure combined with the original materials used in the Bio-Shield would not allow for a stable structure to be extracted. The water used in the core drilling process proved to erode the sand mixture of the Bio-Shield leaving the steel aggregate to act as ball bearings against the core drill bit. A redesign is being completed to extract the 309 PRTR and entire Bio-Shield structure together as one monolith weighing 1100 Ton by cutting structural concrete supports. In addition, the PRTR has hundreds of contaminated process tubes and pipes that have to be severed to allow for a uniformly flush fit with a lower lifting frame. Thirty-two 50 mm (2 in) core drills must be connected with thirty-two wire saw cuts to allow for lifting columns to be inserted. Then eight primary saw cuts must be completed to severe the PRTR from the 309 Facility. Once the weight of the PRTR is transferred to the lifting frame, then the PRTR may be lifted out of the facility. The critical lift will be executed using four 450 Ton strand jacks mounted on a 9 m (30 LF) tall mobile lifting frame that will allow the PRTR to be transported by eight 600 mm (24 in) Slide Shoes. The PRTR will then be placed on a twenty-four line, double wide, self powered Goldhofer for transfer to the onsite CERCLA Disposal Cell (ERDF Facility), approximately 33 km (20 miles) away. (authors)

  5. Growing Sweetpotatoes in New Hampshire BECKY SIDEMAN, PHD

    E-Print Network [OSTI]

    New Hampshire, University of

    Growing Sweetpotatoes in New Hampshire BECKY SIDEMAN, PHD Sweetpotato (Ipomoea batatas) is a member food for deer in midsummer, a lightweight electric fence may successfully keep the deer at bay

  6. Growing Up in Scotland: first research report on Sweep 1 

    E-Print Network [OSTI]

    Anderson, Simon; Bradshaw, Paul; Cunningham-Burley, Sarah; Hayes, Fenella; Jamieson, Lynn; MacGregor, Andy; Marryat, Louise; Wasoff, Fran

    The Growing Up in Scotland study ( GUS) is an important and ambitious new longitudinal research project aimed at tracking the lives of a cohort of Scottish children from the early years, through childhood and beyond. Funded ...

  7. Growing Up in Scotland: Year 3 - Non-resident Parents 

    E-Print Network [OSTI]

    Marryat, Louise; Reid, Susan; Wasoff, Fran

    2009-01-21

    This report uses data from the Growing Up in Scotland study (GUS) to explore the prevalence of, and many issues related to, non-resident parenthood in Scotland specifically in relation to young and very young children. ...

  8. Growing Energy - How Biofuels Can Help End America's Oil Dependence...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    27 percent of U.S. global warming pollution, as well as soot and smog that damage human lungs. NRDC.Growing.Energy.Final.3.pdf More Documents & Publications Biofuels & Greenhouse...

  9. Circulating Fluidized Bed (CFB) Boilers Market will grow due...

    Open Energy Info (EERE)

    Energy Concerns to Push Global Market to Grow at 8.1% CAGR from 2013 to 2019 Oil Shale Market is Estimated to Reach USD 7,400.70 Million by 2022 more Group members (32)...

  10. Learn How To Grow Your Business Through Government Contracting

    Broader source: Energy.gov [DOE]

    OPEN for Government Contracts presents: Summit for Success is a FREE event hosted by American Express OPEN. The "Grow Your Business Through Government Contracting” events are FREE, day-long events focusing on small business government contracting.

  11. System development & validation process for emerging growing organizations

    E-Print Network [OSTI]

    Almazán López, José Antonio

    2009-01-01

    This thesis has the main purpose of presenting the Development and Validation phase of the product development system from the point of view of an emerging and growing product development organization, denoting the obstacles ...

  12. Growing Up in Scotland: Year 3 - Food and Activity 

    E-Print Network [OSTI]

    Marryat, Louise; Valeria, Skafida; Webster, Catriona

    2009-01-21

    This report uses data from the Growing Up in Scotland study to explore the prevalence of, and many issues related to, food and activity in Scotland specifically in relation to young children.

  13. Fact #567: April 20, 2009 Cars are Growing Older

    Broader source: Energy.gov [DOE]

    The median age of cars continues to grow in 2008 while the median age of light trucks has remained fairly constant over the last ten years. The average age for all trucks, which includes heavy...

  14. Removing Stains from Washable Fabrics. 

    E-Print Network [OSTI]

    Beard, Ann Vanderpoorten

    1988-01-01

    unique treatment be cause of chemical make-up or physical characteristics. (Examples: chewing gum, iodine, lead pencil) Stain Removal Products Bleaches Chlorine bleaches contain a hypochlorite com pound. Do not use them on wool, silk, polyurethane... foam, spandex or blends of these fibers; on finishes which are embossed or flame retardant; or on fabrics labeled no chlorine bleach. Avoid contact with metal. Always follow package instructions for dilu tion. Liquid chlorine bleaches lose strength...

  15. IDENTIFYING CANDIDATE PROTEIN FOR REMOVAL OF ENVIRONMENTALLY

    E-Print Network [OSTI]

    Uppsala Universitet

    IDENTIFYING CANDIDATE PROTEIN FOR REMOVAL OF ENVIRONMENTALLY HAZARDOUS SUBSTANCES Pharem Biotech products and technologies for removing environmental hazardous substances in our everyday life. The products can be applied in areas from the private customer up to the global corporate perspective

  16. Mexico HEU Removal | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Apply for Our Jobs Our Jobs Working at NNSA Blog Home content Four-Year Plan Mexico HEU Removal Mexico HEU Removal Location Mexico United States 24 24' 35.298" N, 102...

  17. Nuclear & Radiological Material Removal | National Nuclear Security...

    National Nuclear Security Administration (NNSA)

    & Radiological Material Removal | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation...

  18. Quick Stain Removal Guide (Spanish) 

    E-Print Network [OSTI]

    Brown, Pamela J.

    2001-08-22

    -5191S de la Oficina de Extensi?n, Etiquetas de Instrucciones y su Ropa). Lleve las prendas de vestir de lavado en seco a tintorer?as profe- sionales. Siga estas pautas para las prendas de vestir lavables: Sepa de qu? es la mancha. Si no sabe, intente...). The Soap and Detergent Association, Marzo/Abril. NY: New York. Laundering Facts. (1991). The Soap and Detergent Association. NY: New York. Beard, A.V. (1989). Removing stains from washable fabrics. Servicio de Extensi?n Agr?cola de Texas. TX: College...

  19. Section 46: Removal of Waste

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust, High-ThroughputUpcomingmagnetoresistanceand Governmentm D m r e DFigureEffects ofRemoval

  20. Method of making thermally removable epoxies

    SciTech Connect (OSTI)

    Loy, Douglas A. (Albuquerque, NM); Wheeler, David R. (Albuquerque, NM); Russick, Edward M. (Rio Rancho, NM); McElhanon, James R. (Albuquerque, NM); Saunders, Randall S. (late of Albuquerque, NM)

    2002-01-01

    A method of making a thermally-removable epoxy by mixing a bis(maleimide) compound to a monomeric furan compound containing an oxirane group to form a di-epoxy mixture and then adding a curing agent at temperatures from approximately room temperature to less than approximately 90.degree. C. to form a thermally-removable epoxy. The thermally-removable epoxy can be easily removed within approximately an hour by heating to temperatures greater than approximately 90.degree. C. in a polar solvent. The epoxy material can be used in protecting electronic components that may require subsequent removal of the solid material for component repair, modification or quality control.

  1. Review on Seismic Rehabilitation of a 56-Story RC Tall Building having Shear Wall System Based on A Nonlinear Dynamic Performance Evaluation

    SciTech Connect (OSTI)

    Epackachi, S.; Esmaili, O. [School of Civil Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Mirghaderi, S. R. [School of Civil Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); The Committee for Revising the Iranian Code of Practice for Seismic Resistance Design of Buildings, Tehran (Iran, Islamic Republic of); Taheri, A. A. [The Committee for Revising the Iranian Code of Practice for Seismic Resistance Design of Buildings, Tehran (Iran, Islamic Republic of)

    2008-07-08

    Tehran tower is a 56 story reinforced concrete tall building consisting of three wings with identical plan dimensions each approximately 48 meters by 22 meters. The three wings are at 120 degree from each other and have no expansions/seismic Joints. This paper contains the consideration of the retrofitting of the Tehran tower based on the findings of an exhaustive investigation of the nonlinear performance evaluation efforts. It has tried to show the procedure followed, methodologies utilized, and the results obtained for life-safety and collapse-prevention evaluation of the building. More over the weak zones of the structure due to analysis results are introduced and appropriate retrofit technique for satisfaction related life-safety and collapse-prevention criteria is presented. Actually in this project to improve the local behavior of coupling panels which are located regularly in main walls and definitely have been recognized as the most vulnerable structural elements, making use of steel plates which are connected to concrete members by chemical anchors has been used as the best retrofitting method for this case. Therefore in the final section of this paper it has been tried to explain the professional practical method utilized to perform the mentioned retrofitting project.

  2. Fuel removal, transport, and storage

    SciTech Connect (OSTI)

    Reno, H.W.

    1986-01-01

    The March 1979 accident at Unit 2 of the Three Mile Island Nuclear Power Station (TMI-2) which damaged the core of the reactor resulted in numerous scientific and technical challenges. Some of those challenges involve removing the core debris from the reactor, packaging it into canisters, loading canisters into a rail cask, and transporting the debris to the Idaho National Engineering Laboratory (INEL) for storage, examination, and preparation for final disposal. This paper highlights how some challenges were resolved, including lessons learned and benefits derived therefrom. Key to some success at TMI was designing, testing, fabricating, and licensing two rail casks, which each provide double containment of the damaged fuel. 10 refs., 12 figs.

  3. Melter Glass Removal and Dismantlement

    SciTech Connect (OSTI)

    Richardson, BS

    2000-10-31

    The U.S. Department of Energy (DOE) has been using vitrification processes to convert high-level radioactive waste forms into a stable glass for disposal in waste repositories. Vitrification facilities at the Savannah River Site (SRS) and at the West Valley Demonstration Project (WVDP) are converting liquid high-level waste (HLW) by combining it with a glass-forming media to form a borosilicate glass, which will ensure safe long-term storage. Large, slurry fed melters, which are used for this process, were anticipated to have a finite life (on the order of two to three years) at which time they would have to be replaced using remote methods because of the high radiation fields. In actuality the melters useable life spans have, to date, exceeded original life-span estimates. Initial plans called for the removal of failed melters by placing the melter assembly into a container and storing the assembly in a concrete vault on the vitrification plant site pending size-reduction, segregation, containerization, and shipment to appropriate storage facilities. Separate facilities for the processing of the failed melters currently do not exist. Options for handling these melters include (1) locating a facility to conduct the size-reduction, characterization, and containerization as originally planned; (2) long-term storing or disposing of the complete melter assembly; and (3) attempting to refurbish the melter and to reuse the melter assembly. The focus of this report is to look at methods and issues pertinent to size-reduction and/or melter refurbishment in particular, removing the glass as a part of a refurbishment or to reduce contamination levels (thus allowing for disposal of a greater proportion of the melter as low level waste).

  4. Composting Successes and Failures Extending the Growing Season Workshop

    E-Print Network [OSTI]

    Amin, S. Massoud

    3/18/2014 1 Composting Successes and Failures Extending the Growing Season Workshop LaMoine Nickel University of MN SWROC March 12, 2014 Beginning of compost process 9/6/2013 Finished compost product 11/19/2013 What is Composting Composting is a biological process in which microorganisms convert organic

  5. Ris Energy Report 2 Three growing concerns sustainability (particularly in

    E-Print Network [OSTI]

    1 Risø Energy Report 2 Three growing concerns ­ sustainability (particularly in the transport sector), security of energy supply and cli- mate change ­ have combined to increase interest in bioenergy and significant changes in energy markets. We even have a new term, "modern bioenergy", to cover those areas

  6. Glass Needs for a Growing Photovoltaics Industry Keith Burrows1

    E-Print Network [OSTI]

    1 Glass Needs for a Growing Photovoltaics Industry Keith Burrows1 and Vasilis Fthenakis1,2* 1 Center for Life Cycle Analysis, Columbia University, New York, NY 2 Photovoltaics Environmental Research Center, Brookhaven National Lab, Upton, NY Abstract With the projected growth in photovoltaics

  7. Growing the renewable chemicals and advanced biofuels cluster in MN

    E-Print Network [OSTI]

    Levinson, David M.

    Growing the renewable chemicals and advanced biofuels cluster in MN #12;Renewable Chemical Value% Reduction 60% Reduction 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Gasoline Corn Ethanol Advanced Biofuel Cellulosic Biofuel Corn Ethanol 20% GHG Reduction Compared to gasoline: Advanced Biofuel 50% GHG Reduction e

  8. Growing and Sustaining Communities with Bioenergy- Text-Alt Version

    Broader source: Energy.gov [DOE]

    From Vero Beach, Florida, to Hugoton, Kansas, to Emmetsburg, Iowa, cellulosic ethanol biorefineries have had major impacts on communities and their residents. In other areas, bioenergy has significant potential to transform current and establish new industry. This short video illustrates how biorefineries and other bioenergy developments can benefit citizens, businesses, and whole communities, helping America’s rural economies grow and thrive.

  9. Country Report Impact of growing urbanization and air pollution on

    E-Print Network [OSTI]

    Singh, Ramesh P.

    discussion is presented here of the degradation in air quality in major cities, the source of the pollutants5 Country Report Impact of growing urbanization and air pollution on the regional climate over. censusindia.net/, Fig. 1). The population growth has been mainly centered around cities due pri- marily

  10. Know and Grow Your Worth: Negotiating the Job Offer and

    E-Print Network [OSTI]

    Know and Grow Your Worth: Negotiating the Job Offer and Managing Your Ongoing Professional Offer Researching salary ranges Answering salary requirements early in process Negotiating salary once offer is made Negotiating other benefits and perks Negotiating raises and promotions once you

  11. Greater fuel diversity needed to meet growing US electricity demand

    SciTech Connect (OSTI)

    Burt, B.; Mullins, S.

    2008-01-15

    Electricity demand is growing in the USA. One way to manage the uncertainty is to diversity fuel sources. Fuel sources include coal, natural gas, nuclear and renewable energy sources. Tables show actual and planned generation projects by fuel types. 1 fig., 2 tabs.

  12. Finite Element Model of Fracture Formation on Growing Surfaces

    E-Print Network [OSTI]

    Prusinkiewicz, Przemyslaw

    Finite Element Model of Fracture Formation on Growing Surfaces Pavol Federl and Przemyslaw-mail: federl|pwp@cpsc.ucalgary.ca Abstract We present a model of fracture formation on surfaces of bilayered materials. The model makes it possible to synthesize patterns of fractures induced by growth or shrinkage

  13. Method for removing contaminants from plastic resin

    DOE Patents [OSTI]

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2008-12-09

    A resin recycling method that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The method includes receiving the resin in container form. The containers are then ground into resin particles. The particles are exposed to a solvent, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. After separating the particles and the resin, a solvent removing agent is used to remove any residual solvent remaining on the resin particles after separation.

  14. PRTR ion exchange vault water removal

    SciTech Connect (OSTI)

    Ham, J.E.

    1995-11-01

    This report documents the removal of radiologically contaminated water from the Plutonium Recycle Test Reactor (PRTR) ion exchange vault. Approximately 57,000 liters (15,000 gallons) of water had accumulated in the vault due to the absence of a rain cover. The water was removed and the vault inspected for signs of leakage. No evidence of leakage was found. The removal and disposal of the radiologically contaminated water decreased the risk of environmental contamination.

  15. Process for particulate removal from coal liquids

    DOE Patents [OSTI]

    Rappe, Gerald C. (Macungie, PA)

    1983-01-01

    Suspended solid particulates are removed from liquefied coal products by first subjecting such products to hydroclone action for removal in the underflow of the larger size particulates, and then subjecting the overflow from said hydroclone action, comprising the residual finer particulates, to an electrostatic field in an electrofilter wherein such finer particulates are deposited in the bed of beads of dielectric material on said filter. The beads are periodically cleaned by backwashing to remove the accumulated solids.

  16. System for removing contaminants from plastic resin

    DOE Patents [OSTI]

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2010-11-23

    A resin recycling system that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The system includes receiving the resin in container form. A grinder grinds the containers into resin particles. The particles are exposed to a solvent in one or more solvent wash vessels, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. A separator is used to separate the resin particles and the solvent. The resin particles are then placed in solvent removing element where they are exposed to a solvent removing agent which removes any residual solvent remaining on the resin particles after separation.

  17. Turkey HEU Removal | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Turkey HEU Removal | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the...

  18. General Counsel Legal Interpretation Regarding Medical Removal...

    Energy Savers [EERE]

    Regarding Medical Removal Protection Benefits Pursuant to 10 CFR Part 850, Chronic Beryllium Disease Prevention Program General Counsel Legal Interpretation Regarding Medical...

  19. Slag capture and removal during laser cutting

    DOE Patents [OSTI]

    Brown, Clyde O. (Newington, CT)

    1984-05-08

    Molten metal removed from a workpiece in a laser cutting operation is blown away from the cutting point by a gas jet and collected on an electromagnet.

  20. Method of making thermally removable polymeric encapsulants

    SciTech Connect (OSTI)

    Small, James H. (Santa Fe, NM); Loy, Douglas A. (Albuquerque, NM); Wheeler, David R. (Albuquerque, NM); McElhanon, James R. (Albuquerque, NM); Saunders, Randall S. (late of Albuquerque, NM)

    2001-01-01

    A method of making a thermally-removable encapsulant by heating a mixture of at least one bis(maleimide) compound and at least one monomeric tris(furan) or tetrakis(furan) compound at temperatures from above room temperature to less than approximately 90.degree. C. to form a gel and cooling the gel to form the thermally-removable encapsulant. The encapsulant can be easily removed within approximately an hour by heating to temperatures greater than approximately 90.degree. C., preferably in a polar solvent. The encapsulant can be used in protecting electronic components that may require subsequent removal of the encapsulant for component repair, modification or quality control.

  1. Use of microalgae to remove pollutants from power plant discharges

    DOE Patents [OSTI]

    Wilde, E.W.; Benemann, J.R.; Weissman, J.C.; Tillett, D.M.

    1991-04-30

    A method and system are described for removing pollutants dissolved in the aqueous discharge of a plant, such as a power plant, from a body of water having known hydraulic and physicochemical characteristics, the method comprising (a) modifying the hydraulic system of the body of water including use of physical barriers to define a zone in a portion of the body of water which zone includes the discharge point and where the water has a range of physicochemical characteristics; (b) selecting a large and preferably filamentous, planktonically growing strain of algae adapted to absorb the particular pollutants and genetically dominating algae at the physicochemical characteristics of the zone; (c) establishing a colony of the selected algal strain in the zone; (d) harvesting a portion of the colony; and (e) reinoculating the zone near the discharge point with a fraction of the harvested portion. The fraction used for reinoculation can be adjusted to balance the rate of pollutant removal to the rate of pollutant discharge. 4 figures.

  2. Growing interfaces uncover universal fluctuations behind scale invariance

    E-Print Network [OSTI]

    Kazumasa A. Takeuchi; Masaki Sano; Tomohiro Sasamoto; Herbert Spohn

    2011-08-10

    Stochastic motion of a point -- known as Brownian motion -- has many successful applications in science, thanks to its scale invariance and consequent universal features such as Gaussian fluctuations. In contrast, the stochastic motion of a line, though it is also scale-invariant and arises in nature as various types of interface growth, is far less understood. The two major missing ingredients are: an experiment that allows a quantitative comparison with theory and an analytic solution of the Kardar-Parisi-Zhang (KPZ) equation, a prototypical equation for describing growing interfaces. Here we solve both problems, showing unprecedented universality beyond the scaling laws. We investigate growing interfaces of liquid-crystal turbulence and find not only universal scaling, but universal distributions of interface positions. They obey the largest-eigenvalue distributions of random matrices and depend on whether the interface is curved or flat, albeit universal in each case. Our exact solution of the KPZ equation provides theoretical explanations.

  3. Renewable energy has political support, room to grow

    SciTech Connect (OSTI)

    NONE

    1997-08-11

    Renewable energy sources enjoy growing political support and have plenty of room to grow in the worldwide energy mix. And grow they will, according to most projections. The US Energy Information Administration`s (EIA`s) International Energy Outlook 1997 says consumption of hydroelectricity and other renewables will increase by 56% during 1995--2015. The renewable share of the total energy mix will remain at about current levels, however. The EIA projection includes only renewable fuels used in the generation of electricity. It therefore excludes most biomass energy. Despite the importance of biomass energy, data on consumption of it are sparse. IEA estimates that in the industrialized world, the biomass share of primary energy consumption amounts to 3.5%. Also excluded from EIA`s projection because of insufficiency of data are dispersed renewables, a category that includes energy consumed at the site of production, such as solar panels used for water heating. This paper discusses regional trends, North American activity, Western Europe, Asian developments, and the rest of the world.

  4. Method of removing contaminants from plastic resins

    DOE Patents [OSTI]

    Bohnert,George W. (Harrisonville, MO); Hand,Thomas E. (Lee's Summit, MO); Delaurentiis,Gary M. (Jamestown, CA)

    2007-08-07

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  5. Method for removing contaminants from plastic resin

    DOE Patents [OSTI]

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2008-12-30

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  6. Method of removing contaminants from plastic resins

    DOE Patents [OSTI]

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2008-11-18

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  7. TABLE OF CONTENTS Tree Maintenance and Removal

    E-Print Network [OSTI]

    US Army Corps of Engineers

    protection should be worn for all tree maintenance and removal operations. b. Training shall be providedEM 385-1-1 30 Nov 14 31-i Section 31 TABLE OF CONTENTS Tree Maintenance and Removal Section: Page ....................................................................... 31-10 31.E Other Operations and Equipment

  8. Test Plan for the overburden removal demonstration

    SciTech Connect (OSTI)

    Rice, P.; Thompson, D.; Winberg, M.; Skaggs, J.

    1993-06-01

    The removal of soil overburdens from contaminated pits and trenches involves using equipment that will remove a small layer of soil from 3 to 6 in. at any time. As a layer of soil is removed, overburden characterization techniques perform surveys to a depth that exceeds each overburden removal layer to ensure that the removed soil will be free of contamination. It is generally expected that no contamination will be found in the soil overburden, which was brought in after the waste was put in place. It is anticipated that some containers in the waste zone have lost their integrity, and the waste leakage from those containers has migrated by gravity downward into the waste zone. To maintain a safe work environment, this method of overburden removal should allow safe preparation of a pit or trench for final remediation. To demonstrate the soil overburden techniques, the Buried Waste Integrated Demonstration Program has contracted vendor services to provide equipment and techniques demonstrating soil overburden removal technology. The demonstration will include tests that will evaluate equipment performance and techniques for removal of overburden soil, control of contamination spread, and dust control. To evaluate the performance of these techniques, air particulate samples, physical measurements of the excavation soil cuts, maneuverability measurements, and time versus volume (rate) of soil removal data will be collected during removal operations. To provide a medium for sample evaluation, the overburden will be spiked at specific locations and depths with rare earth tracers. This test plan will be describe the objectives of the demonstration, data quality objectives, methods to be used to operate the equipment and use the techniques in the test area, and methods to be used in collecting data during the demonstration.

  9. Removable bearing arrangement for a wind turbine generator

    DOE Patents [OSTI]

    Bagepalli, Bharat Sampathkumaran; Jansen, Patrick Lee; Gadre, Aniruddha Dattatraya

    2010-06-15

    A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

  10. Method for changing removable bearing for a wind turbine generator

    DOE Patents [OSTI]

    Bagepalli, Bharat Sampathkumaran (Niskayuna, NY); Jansen, Patrick Lee (Scotia, NY), Gadre; Aniruddha Dattatraya (Rexford, NY)

    2008-04-22

    A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

  11. Calif. ISO gears up for growing renewables portfolio

    SciTech Connect (OSTI)

    NONE

    2010-11-15

    Operating the grid is going to become more of a challenge as wind and solar generation -- the biggest two contributors with the most hourly and daily variations -- grow over time. Forecasting exactly how much capacity will be available a mere one hour ahead still remains difficult. More renewable generation is not good business for conventional peaking and load-following thermal generation, mostly burning natural gas. Their revenues, depending on the specific scenario considered, may drop by 20 to 40 percent. Something has to be done to sustain these critical players even as their output is not required as much as in the past.

  12. Apparatus for growing HgI.sub.2 crystals

    DOE Patents [OSTI]

    Schieber, Michael M. (Jerusalem, IL); Beinglass, Israel (Jerusalem, IL); Dishon, Giora (Jerusalem, IL)

    1978-01-01

    A method and horizontal furnace for vapor phase growth of HgI.sub.2 crystals which utilizes controlled axial and radial airflow to maintain the desired temperature gradients. The ampoule containing the source material is rotated while axial and radial air tubes are moved in opposite directions during crystal growth to maintain a desired distance and associated temperature gradient with respect to the growing crystal, whereby the crystal interface can advance in all directions, i.e., radial and axial according to the crystallographic structure of the crystal. Crystals grown by this method are particularly applicable for use as room-temperature nuclear radiation detectors.

  13. Growing Cutting-edge X-ray Optics

    ScienceCinema (OSTI)

    Ray Conley

    2013-07-17

    Ever imagined that an Xbox controller could help open a window into a world spanning just one billionth of a meter? Brookhaven Lab's Ray Conley grows cutting-edge optics called multilayer Laue lenses (MLL) one atomic layer at a time to focus high-energy x-rays to within a single nanometer. To achieve this focusing feat, Ray uses a massive, custom-built atomic deposition device, an array of computers, and a trusty Xbox controller. These lenses will be deployed at the Lab's National Synchrotron Light Source II, due to begin shining super-bright light on pressing scientific puzzles in 2015

  14. Financing the Growing American Auto Industry | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would likeUniverse (Journal Article) |Final Reportthe Growing American Auto Industry Financing

  15. In situ removal of contamination from soil

    DOE Patents [OSTI]

    Lindgren, Eric R. (Albuquerque, NM); Brady, Patrick V. (Albuquerque, NM)

    1997-01-01

    A process of remediation of cationic heavy metal contamination from soil utilizes gas phase manipulation to inhibit biodegradation of a chelating agent that is used in an electrokinesis process to remove the contamination, and further gas phase manipulation to stimulate biodegradation of the chelating agent after the contamination has been removed. The process ensures that the chelating agent is not attacked by bioorganisms in the soil prior to removal of the contamination, and that the chelating agent does not remain as a new contaminant after the process is completed.

  16. In situ removal of contamination from soil

    DOE Patents [OSTI]

    Lindgren, E.R.; Brady, P.V.

    1997-10-14

    A process of remediation of cationic heavy metal contamination from soil utilizes gas phase manipulation to inhibit biodegradation of a chelating agent that is used in an electrokinesis process to remove the contamination. The process also uses further gas phase manipulation to stimulate biodegradation of the chelating agent after the contamination has been removed. The process ensures that the chelating agent is not attacked by bioorganisms in the soil prior to removal of the contamination, and that the chelating agent does not remain as a new contaminant after the process is completed. 5 figs.

  17. Far East LPG sales will grow faster than in West

    SciTech Connect (OSTI)

    1996-12-30

    LPG sales through 2010 in regions east of the Suez Canal (East of Suez) will grow at more than twice those in regions west of the canal. East-of-Suez sales will grow at more than 4.0%/year, compared to slightly less than 2.0%/year growth in sales West of Suez. East-of-Suez sales will reach 92 million tons/year (tpy) by 2010, accounting for 39% of the worldwide total. This share was 31% in1995 and only 27% in 1990. LPG sales worldwide will reach 192 million tons in 2000 and 243 million tpy by 2010. In 1995, they were 163 million tons. These are some of the major conclusions of a recent study by Frank R. Spadine, Christine Kozar, and Rudy Clark of New York City-based consultant Poten and Partners Inc. Details of the study are in the fall report ``World Trade in LPG 1990--2010``. This paper discusses demand segments, seaborne balance, Western sources, largest trading region, North American supplies, and other supplies.

  18. Part removal of 3D printed parts

    E-Print Network [OSTI]

    Peña Doll, Mateo

    2014-01-01

    An experimental study was performed to understand the correlation between printing parameters in the FDM 3D printing process, and the force required to remove a part from the build platform of a 3D printing using a patent ...

  19. Method of removing polychlorinated biphenyl from oil

    DOE Patents [OSTI]

    Cook, Gus T. (Paducah, KY); Holshouser, Stephen K. (Boaz, KY); Coleman, Richard M. (Paducah, KY); Harless, Charles E. (Smithland, KY); Whinnery, III, Walter N. (Paducah, KY)

    1983-01-01

    Polychlorinated biphenyls are removed from oil by extracting the biphenyls into methanol. The mixture of methanol and extracted biphenyls is distilled to separate methanol therefrom, and the methanol is recycled for further use in extraction of biphenyls from oil.

  20. Method of removing polychlorinated biphenyl from oil

    DOE Patents [OSTI]

    Cook, G.T.; Holshouser, S.K.; Coleman, R.M.; Harless, C.E.; Whinnery, W.N. III

    1982-03-17

    Polychlorinated biphenyls are removed from oil by extracting the biphenyls into methanol. The mixture of methanol and extracted biphenyls is distilled to separate methanol therefrom, and the methanol is recycled for further use in extraction of biphenyls from oil.

  1. Ultrasound : an alternative solution for removing tattoos

    E-Print Network [OSTI]

    Teng, Jennifer

    2005-01-01

    The recent influx of tattoos has been accompanied by a rise in demand for tattoo removals. Due to the recent success of ultrasound as a noninvasive alternative for multiple medical therapies, the feasibility of ultrasound-mediated ...

  2. Advanced Water Removal via Membrane Solvent Extraction

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Water Removal via Membrane Solvent Extraction Reduction in energy and water use for the ethanol industry Ethanol is the leading biofuel in the U.S. with 13 Billion gallons produced...

  3. Method for removing RFI from SAR images

    DOE Patents [OSTI]

    Doerry, Armin W.

    2003-08-19

    A method of removing RFI from a SAR by comparing two SAR images on a pixel by pixel basis and selecting the pixel with the lower magnitude to form a composite image. One SAR image is the conventional image produced by the SAR. The other image is created from phase-history data which has been filtered to have the frequency bands containing the RFI removed.

  4. Laser removal of sludge from steam generators

    DOE Patents [OSTI]

    Nachbar, Henry D. (Ballston Lake, NY)

    1990-01-01

    A method of removing unwanted chemical deposits known as sludge from the metal surfaces of steam generators with laser energy is provided. Laser energy of a certain power density, of a critical wavelength and frequency, is intermittently focused on the sludge deposits to vaporize them so that the surfaces are cleaned without affecting the metal surface (sludge substrate). Fiberoptic tubes are utilized for laser beam transmission and beam direction. Fiberoptics are also utilized to monitor laser operation and sludge removal.

  5. Oil removal from water via adsorption 

    E-Print Network [OSTI]

    Jacobs, William Edward

    1973-01-01

    WILLIAM EDWARD JACOBS 1974 OIL REMOVAL FROM WATER VIA ADSORPTION A Thesis by WILLIAM EDWARD JACOBS Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE... December 1973 Major Subject: Civil Engineering OIL REMOVAL FROM WATER VIA ADSORPTION A Thesis by WILLIAM EDWARD JACOBS Approved as to style and content by: C airman of Committee ea o Department m er Member Memb December 1973 ABSTRACT Oil...

  6. The three-dimensional morphology of growing dendrites

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Gibbs, J. W.; Mohan, K. A.; Gulsoy, E. B.; Shahani, A. J.; Xiao, X.; Bouman, C. A.; De Graef, M.; Voorhees, P. W.

    2015-07-03

    The processes controlling the morphology of dendrites have been of great interest to a wide range of communities, since they are examples of an out-of-equilibrium pattern forming system, there is a clear connection with battery failure processes, and their morphology sets the properties of many metallic alloys. We determine the three-dimensional morphology of free growing metallic dendrites using a novel X-ray tomographic technique that improves the temporal resolution by more than an order of magnitude compared to conventional techniques. These measurements show that the growth morphology of metallic dendrites is surprisingly different from that seen in model systems, the morphologymore »is not self-similar with distance back from the tip, and that this morphology can have an unexpectedly strong influence on solute segregation in castings. These experiments also provide benchmark data that can be used to validate simulations of free dendritic growth.« less

  7. Ranking nodes in growing networks: When PageRank fails

    E-Print Network [OSTI]

    Mariani, Manuel Sebastian; Zhang, Yi-Cheng

    2015-01-01

    PageRank is arguably the most popular ranking algorithm which is being applied in real systems ranging from information to biological and infrastructure networks. Despite its outstanding popularity and broad use in different areas of science, the relation between the algorithm's efficacy and properties of the network on which it acts has not yet been fully understood. We study here PageRank's performance on a network model supported by real data, and show that realistic temporal effects make PageRank fail in individuating the most valuable nodes for a broad range of model parameters. Results on real data are in qualitative agreement with our model-based findings. This failure of PageRank reveals that the static approach to information filtering is inappropriate for a broad class of growing systems, and suggest that time-dependent algorithms that are based on the temporal linking patterns of these systems are needed to better rank the nodes.

  8. Growing timescales and lengthscales characterizing vibrations of amorphous solids

    E-Print Network [OSTI]

    Ludovic Berthier; Patrick Charbonneau; Yuliang Jin; Giorgio Parisi; Beatriz Seoane; Francesco Zamponi

    2015-11-13

    Low-temperature properties of crystalline solids can be understood using harmonic perturbations around a perfect lattice, as in Debye's theory. Low-temperature properties of amorphous solids, however, strongly depart from such descriptions, displaying enhanced transport, activated slow dynamics across energy barriers, excess vibrational modes with respect to Debye's theory (i.e., a Boson Peak), and complex irreversible responses to small mechanical deformations. These experimental observations indirectly suggest that the dynamics of amorphous solids becomes anomalous at low temperatures. Here, we provide direct numerical evidence that vibrations change nature at a well-defined location deep inside the glass phase of a simple glass former. We provide a real-space description of this transition and of the rapidly growing time and length scales that accompany it. We discuss our results both in the theoretical context of the recently discovered Gardner phase transition and in connection with low-temperature glass experiments.

  9. Fast-growing willow shrub named `Tully Champion`

    DOE Patents [OSTI]

    Abrahamson, Lawrence P.; Kopp, Richard F.; Smart, Lawrence B.; Volk, Timothy A.

    2007-08-28

    A distinct female cultivar of Salix viminalis.times.S. miyabeana named `Tully Champion`, characterized by rapid stem growth producing greater than 25% more woody biomass than two current production clones (Salix dasyclados `SV1` and Salix miyabeana `SX64`), more than 2.5-fold greater biomass than one of its parents (Salix miyabeana `SX67`), and nearly 3-fold more biomass than another production clone (Salix sacchalinensis, `SX61`) when grown in the same field for the same length of time (two growing seasons after coppice) in Tully, N.Y. `Tully Champion` can be planted from dormant stem cuttings, produces multiple stems after coppice, and the stem biomass can be harvested when the plant is dormant. In the spring following harvest, the plant will re-sprout very vigorously, producing new stems that can be harvested repeatedly after two to four years of growth. `Tully Champion` displays a low incidence of rust disease and is not damaged by potato leafhoppers.

  10. Development of Remove Sensing Instrumentation for NOx and PM...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Development of Remove Sensing Instrumentation for NOx and PM Emissions from Heavy Duty Trucks Development of Remove Sensing Instrumentation for NOx and PM Emissions from Heavy Duty...

  11. Oak Ridge Removes Laboratory's Greatest Source of Groundwater...

    Energy Savers [EERE]

    Removes Laboratory's Greatest Source of Groundwater Contamination Oak Ridge Removes Laboratory's Greatest Source of Groundwater Contamination May 1, 2012 - 12:00pm Addthis Workers...

  12. New Research Facility to Remove Hurdles to Offshore Wind and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research Facility to Remove Hurdles to Offshore Wind and Water Power Development New Research Facility to Remove Hurdles to Offshore Wind and Water Power Development January 10,...

  13. Evaluation of Passive and Active Soot Filters for Removal of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Passive and Active Soot Filters for Removal of Particulate Emissions from Diesel Engines Evaluation of Passive and Active Soot Filters for Removal of Particulate Emissions from...

  14. Self-propelled sweeping removal of dropwise condensate (Journal...

    Office of Scientific and Technical Information (OSTI)

    Self-propelled sweeping removal of dropwise condensate Citation Details In-Document Search Title: Self-propelled sweeping removal of dropwise condensate Authors: Qu, Xiaopeng 1 ;...

  15. Hardboiled eggs petri dishes for growing tooth microbes (find proper agar)

    E-Print Network [OSTI]

    Materials Hardboiled eggs cola OJ Water petri dishes for growing tooth microbes (find proper agar) activities: roleplay egg in acid grow microbes Intro so just a little about myself; name; Im a Chemist I go

  16. EIA: High Oil Prices, GHG Controls Would Help Clean Energy Grow...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EIA: High Oil Prices, GHG Controls Would Help Clean Energy Grow EIA: High Oil Prices, GHG Controls Would Help Clean Energy Grow April 1, 2009 - 11:35am Addthis The growth of...

  17. Partnering with Utilities and Other Program Administrators to Sustain and Grow Your Energy Efficiency Initiatives

    Broader source: Energy.gov [DOE]

    This presentation contains information on Partnering with Utilities and Other Program Administrators to Sustain and Grow Your Energy Efficiency Initiatives.

  18. System for removal of arsenic from water

    DOE Patents [OSTI]

    Moore, Robert C.; Anderson, D. Richard

    2004-11-23

    Systems for removing arsenic from water by addition of inexpensive and commonly available magnesium oxide, magnesium hydroxide, calcium oxide, or calcium hydroxide to the water. The hydroxide has a strong chemical affinity for arsenic and rapidly adsorbs arsenic, even in the presence of carbonate in the water. Simple and commercially available mechanical systems for removal of magnesium hydroxide particles with adsorbed arsenic from drinking water can be used, including filtration, dissolved air flotation, vortex separation, or centrifugal separation. A system for continuous removal of arsenic from water is provided. Also provided is a system for concentrating arsenic in a water sample to facilitate quantification of arsenic, by means of magnesium or calcium hydroxide adsorption.

  19. Technetium Removal Using Tc-Goethite Coprecipitation

    SciTech Connect (OSTI)

    Um, Wooyong; Wang, Guohui; Jung, Hun Bok; Peterson, Reid A.

    2013-11-18

    This report describes the results from laboratory tests performed at Pacific Northwest National Laboratory for the U.S. Department of Energy (DOE) EM-31 Support Program (EMSP) subtask, “Low temperature waste forms coupled with technetium removal using an alternative immobilization process such as Fe(II) treated-goethite precipitation” to increase our understanding of 99Tc long-term stability in goethite mineral form and the process that controls the 99Tc(VII) reduction and removal by the final Fe (oxy)hydroxide forms. The overall objectives of this task were to 1) evaluate the transformation process of Fe (oxy)hydroxide solids to the more crystalline goethite (?-FeOOH) mineral for 99Tc removal and 2) determine the mechanism that limits 99Tc(IV) reoxidation in Fe(II)-treated 99Tc-goethite mineral and 3) evaluate whether there is a long-term 99Tcoxidation state change for Tc sequestered in the iron solids.

  20. Properly engineer lead paint removal projects

    SciTech Connect (OSTI)

    Kaelin, A.B.

    1996-01-01

    Deciding how to mitigate the hazards during lead paint removal is complex and requires consideration of many variables. Assessment of public health risk, environmental impact, and emissions potential of the operations must be considered. Additionally, the removal technique, containment system, and monitoring criteria must be developed. This article presents an integrated approach to identifying lead hazards, assessing risks to workers, the environment, and the public, developing the appropriate maintenance strategy, and selecting paint removal and containment systems. Also considered are guidelines for selecting a third party to design the overall project. This approach is based on a decision path that provides criteria for project assessment in an orderly fashion. The design of lead paint management projects in industrial applications requires consideration of the variables shown in the decision path.

  1. Method of making thermally removable polyurethanes

    SciTech Connect (OSTI)

    Loy, Douglas A. (Albuquerque, NM); Wheeler, David R. (Albuquerque, NM); McElhanon, James R. (Livermore, CA); Saunders, Randall S. (late of Albuquerque, NM); Durbin-Voss, Marvie Lou (Albuquerque, NM)

    2002-01-01

    A method of making a thermally-removable polyurethane material by heating a mixture of a maleimide compound and a furan compound, and introducing alcohol and isocyanate functional groups, where the alcohol group and the isocyanate group reacts to form the urethane linkages and the furan compound and the maleimide compound react to form the thermally weak Diels-Alder adducts that are incorporated into the backbone of the urethane linkages during the formation of the polyurethane material at temperatures from above room temperature to less than approximately 90.degree. C. The polyurethane material can be easily removed within approximately an hour by heating to temperatures greater than approximately 90.degree. C. in a polar solvent. The polyurethane material can be used in protecting electronic components that may require subsequent removal of the solid material for component repair, modification or quality control.

  2. The removal of precious metals by conductive polymer filtration

    SciTech Connect (OSTI)

    Cournoyer, M.E.; Stark, P.C.; Trujillo, S.M.; Aguino, R.E.

    1997-12-31

    The growing demand for platinum-group metals (PGM) for several applications within the DOE complex and in industry, the need for modern and clean processes and the increasing volume of low grade material for secondary PGM recovery have a direct impact on the industrial practice of recovering and refining of precious metals. PGM recovery have a direct impact on the industrial practice of recovering and refining of precious metals. With precipitation-dissolution methods being the most common method of recovery, there is a tremendous need for advanced metal ion recovery and waste minimization techniques. Here at Los Alamos there is an integrated program in ligand-design and separation`s chemistry for recovery of actinide and toxic metals from variety of process streams. In the present investigations, a novel hollow fiber membrane (CPI) is characterized and its selectivity for PGM reported. In addition, a continuous single unit operation is proposed for the removal, concentration and recovery of platinum from catalytic and electroplating process streams is proposed.

  3. Biotechnology and genetic optimization of fast-growing hardwoods

    SciTech Connect (OSTI)

    Garton, S.; Syrkin-Wurtele, E.; Griffiths, H.; Schell, J.; Van Camp, L.; Bulka, K. (NPI, Salt Lake City, UT (United States))

    1991-02-01

    A biotechnology research program was initiated to develop new clones of fast-growing Populus clones resistant to the herbicide glyphosate and resistant to the leaf-spot and canker disease caused by the fungus Septoria musiva. Glyphosate-resistant callus was selected from stem segments cultured in vitro on media supplemented with the herbicide. Plants were regenerated from the glyphosate-resistant callus tissue. A portion of plants reverted to a glyphosate susceptible phenotype during organogenesis. A biologically active filtrate was prepared from S. musiva and influenced fresh weight of Populus callus tissue. Disease-resistant plants were produced through somaclonal variation when shoots developed on stem internodes cultured in vitro. Plantlets were screened for disease symptoms after spraying with a suspension of fungal spores. A frequency of 0.83 percent variant production was observed. Genetically engineered plants were produced after treatment of plant tissue with Agrobacterium tumefasciens strains carrying plasmid genes for antibiotic resistance. Transformers were selected on media enriched with the antibiotic, kanamycin. Presence of foreign DNA was confirmed by Southern blot analysis. Protoplasts of popular were produced but did not regenerate into plant organs. 145 refs., 12 figs., 36 tabs.

  4. Interest grows in African oil and gas opportunities

    SciTech Connect (OSTI)

    Knott, D.

    1997-05-12

    As African countries continue a slow drift towards democratic government and market economics, the continent is increasingly attractive to international oil and gas companies. Though Africa remains politically diverse, and its volatile politics remains a major barrier to petroleum companies, a number of recent developments reflect its growing significance for the industry. Among recent projects and events reflecting changes in Africa: oil and gas exporter Algeria has invited foreign oil companies to help develop major gas discoveries, with a view to boosting exports to Europe; oil and gas producer Egypt invited foreign companies to explore in the Nile Delta region, and the result appears to be a flowering world scale gas play; west African offshore exploration has entered deep water and new areas, and a number of major projects are expected in years to come; Nigeria`s reputation as a difficult place to operate has been justified by recent political and civil events, but a long-planned liquefied natural gas (LNG) export plant is being built there; South Africa, which has returned to the international scene after years of trade isolation because of apartheid, is emerging as a potential driver for energy industry schemes throughout the continent. Activities are discussed.

  5. Arsenic removal in conjunction with lime softening

    DOE Patents [OSTI]

    Khandaker, Nadim R.; Brady, Patrick V.; Teter, David M.; Krumhansl, James L.

    2004-10-12

    A method for removing dissolved arsenic from an aqueous medium comprising adding lime to the aqueous medium, and adding one or more sources of divalent metal ions other than calcium and magnesium to the aqueous medium, whereby dissolved arsenic in the aqueous medium is reduced to a lower level than possible if only the step of adding lime were performed. Also a composition of matter for removing dissolved arsenic from an aqueous medium comprising lime and one or more sources of divalent copper and/or zinc metal ions.

  6. Sorbents for mercury removal from flue gas

    SciTech Connect (OSTI)

    Granite, Evan J.; Hargis, Richard A.; Pennline, Henry W.

    1998-01-01

    A review of the various promoters and sorbents examined for the removal of mercury from flue gas is presented. Commercial sorbent processes are described along with the chemistry of the various sorbent-mercury interactions. Novel sorbents for removing mercury from flue gas are suggested. Since activated carbons are expensive, alternate sorbents and/or improved activated carbons are needed. Because of their lower cost, sorbent development work can focus on base metal oxides and halides. Additionally, the long-term sequestration of the mercury on the sorbent needs to be addressed. Contacting methods between the flue gas and the sorbent also merit investigation.

  7. Process for removing metals from water

    DOE Patents [OSTI]

    Napier, J.M.; Hancher, C.M.; Hackett, G.D.

    1987-06-29

    A process for removing metals from water including the steps of prefiltering solids from the water, adjusting the pH to between about 2 and 3, reducing the amount of dissolved oxygen in the water, increasing the pH to between about 6 and 8, adding water-soluble sulfide to precipitate insoluble sulfide- and hydroxide-forming metals, adding a containing floc, and postfiltering the resultant solution. The postfiltered solution may optionally be eluted through an ion exchange resin to remove residual metal ions. 2 tabs.

  8. Method of making thermally removable adhesives

    DOE Patents [OSTI]

    Aubert, James H.

    2004-11-30

    A method of making a thermally-removable adhesive is provided where a bismaleimide compound, a monomeric furan compound, containing an oxirane group an amine curative are mixed together at an elevated temperature of greater than approximately 90.degree. C. to form a homogeneous solution, which, when cooled to less than approximately 70.degree. C., simultaneously initiates a Diels-Alder reaction between the furan and the bismaleimide and a epoxy curing reaction between the amine curative and the oxirane group to form a thermally-removable adhesive. Subsequent heating to a temperature greater than approximately 100.degree. C. causes the adhesive to melt and allows separation of adhered pieces.

  9. Recommendation 183: Preferred Alternative for the Removal of Hexavalent Chromium

    Broader source: Energy.gov [DOE]

    The ORSSAB Recommendation to DOE on the Preferred Alternative for the Removal of Hexavalent Chromium.

  10. Pentek metal coating removal system: Baseline report

    SciTech Connect (OSTI)

    1997-07-31

    The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

  11. Method of removing cesium from steam

    DOE Patents [OSTI]

    Carson, Jr., Neill J. (Clarendon Hills, IL); Noland, Robert A. (Oak Park, IL); Ruther, Westly E. (Skokie, IL)

    1991-01-01

    Method for removal of radioactive cesium from a hot vapor, such as high temperature steam, including the steps of passing input hot vapor containing radioactive cesium into a bed of silicate glass particles and chemically incorporating radioactive cesium in the silicate glass particles at a temperature of at least about 700.degree. F.

  12. Tank waste remediation system compensatory measure removal

    SciTech Connect (OSTI)

    MILLIKEN, N.J.

    1999-05-18

    In support of Fiscal Year 1998 Performance Agreement TWR1.4.3, ''Replace Compensatory Measures,'' the Tank Waste Remediation System is documenting the completion of field modifications supporting the removal of the temporary exemptions from the approved Tank Waste Remediation System Technical Safety Requirements (TSRs), HNF-SD-WM-TSR-006. These temporary exemptions or compensatory measures expire September 30, 1998.

  13. The Scottish Government's Policy on Woodland Removal

    E-Print Network [OSTI]

    significant woodland removal associated with landscape design, restoration of priority habitats, wind farms associated with the internal re-design of woodlands to meet the UK Forestry Standard. #12;4 | Control comprises 18% of the world's greenhouse gas emissions (compared to 25% from electricity and heat generation

  14. Method of preparation of removable syntactic foam

    DOE Patents [OSTI]

    Arnold, Jr., Charles (Albuquerque, NM); Derzon, Dora K. (Albuquerque, NM); Nelson, Jill S. (Albuquerque, NM); Rand, Peter B. (Albuquerque, NM)

    1995-01-01

    Easily removable, environmentally safe, low-density, syntactic foams are disclosed which are prepared by mixing insoluble microballoons with a solution of water and/or alcohol-soluble polymer to produce a pourable slurry, optionally vacuum filtering the slurry in varying degrees to remove unwanted solvent and solute polymer, and drying to remove residual solvent. The properties of the foams can be controlled by the concentration and physical properties of the polymer, and by the size and properties of the microballoons. The suggested solute polymers are non-toxic and soluble in environmentally safe solvents such as water or low-molecular weight alcohols. The syntactic foams produced by this process are particularly useful in those applications where ease of removability is beneficial, and could find use in packaging recoverable electronic components, in drilling and mining applications, in building trades, in art works, in the entertainment industry for special effects, in manufacturing as temporary fixtures, in agriculture as temporary supports and containers and for delivery of fertilizer, in medicine as casts and splints, as temporary thermal barriers, as temporary protective covers for fragile objects, as filters for particulate matter, which matter may be easily recovered upon exposure to a solvent, as in-situ valves (for one-time use) which go from maximum to minimum impedance when solvent flows through, and for the automatic opening or closing of spring-loaded, mechanical switches upon exposure to a solvent, among other applications.

  15. Method of preparation of removable syntactic foam

    DOE Patents [OSTI]

    Arnold, C. Jr.; Derzon, D.K.; Nelson, J.S.; Rand, P.B.

    1995-07-11

    Easily removable, environmentally safe, low-density, syntactic foams are disclosed which are prepared by mixing insoluble microballoons with a solution of water and/or alcohol-soluble polymer to produce a pourable slurry, optionally vacuum filtering the slurry in varying degrees to remove unwanted solvent and solute polymer, and drying to remove residual solvent. The properties of the foams can be controlled by the concentration and physical properties of the polymer, and by the size and properties of the microballoons. The suggested solute polymers are non-toxic and soluble in environmentally safe solvents such as water or low-molecular weight alcohols. The syntactic foams produced by this process are particularly useful in those applications where ease of removability is beneficial, and could find use in packaging recoverable electronic components, in drilling and mining applications, in building trades, in art works, in the entertainment industry for special effects, in manufacturing as temporary fixtures, in agriculture as temporary supports and containers and for delivery of fertilizer, in medicine as casts and splints, as temporary thermal barriers, as temporary protective covers for fragile objects, as filters for particulate matter, which matter may be easily recovered upon exposure to a solvent, as in-situ valves (for one-time use) which go from maximum to minimum impedance when solvent flows through, and for the automatic opening or closing of spring-loaded, mechanical switches upon exposure to a solvent, among other applications. 1 fig.

  16. Photoacoustic removal of occlusions from blood vessels

    DOE Patents [OSTI]

    Visuri, Steven R. (Livermore, CA); Da Silva, Luiz B. (Danville, CA); Celliers, Peter M. (Berkeley, CA); London, Richard A. (Orinda, CA); Maitland, IV, Duncan J. (Lafayette, CA); Esch, Victor C. (San Francisco, CA)

    2002-01-01

    Partial or total occlusions of fluid passages within the human body are removed by positioning an array of optical fibers in the passage and directing treatment radiation pulses along the fibers, one at a time, to generate a shock wave and hydrodynamics flows that strike and emulsify the occlusions. A preferred application is the removal of blood clots (thrombin and embolic) from small cerebral vessels to reverse the effects of an ischemic stroke. The operating parameters and techniques are chosen to minimize the amount of heating of the fragile cerebral vessel walls occurring during this photo acoustic treatment. One such technique is the optical monitoring of the existence of hydrodynamics flow generating vapor bubbles when they are expected to occur and stopping the heat generating pulses propagated along an optical fiber that is not generating such bubbles.

  17. IMPROVED PROCESSES TO REMOVE NAPHTHENIC ACIDS

    SciTech Connect (OSTI)

    Aihua Zhang; Qisheng Ma; Kangshi Wang, William A. Goddard, Yongchun Tang

    2005-05-05

    In the second year of this project, we continued our effort to develop low temperature decarboxylation catalysts and investigate the behavior of these catalysts at different reaction conditions. We conducted a large number of dynamic measurements with crude oil and model compounds to obtain the information at different reaction stages, which was scheduled as the Task2 in our work plan. We developed a novel adsorption method to remove naphthenic acid from crude oil using naturally occurring materials such as clays. Our results show promise as an industrial application. The theoretical modeling proposed several possible reaction pathways and predicted the reactivity depending on the catalysts employed. From all of these studies, we obtained more comprehensive understanding about catalytic decarboxylation and oil upgrading based on the naphthenic acid removal concept.

  18. Removal of mercury from waste gases

    SciTech Connect (OSTI)

    Muster, U.; Marr, R.; Pichler, G.; Kremshofer, S.; Wilferl, R.; Draxler, J.

    1996-12-31

    Waste and process gases from thermal power, incineration and metallurgical plants or those from cement and alkali chloride industries contain metallic, inorganic and organic mercury. Widespread processes to remove the major amount of mercury are absorption and adsorption. Caused by the lowering of the emission limit from 200 to 50 {mu}g/m{sup 3} [STP] by national and European legislators, considerable efforts were made to enhance the efficiency of the main separation units of flue gas cleaning plants. Specially impregnated ceramic carriers can be used for the selective separation of metallic, inorganic and organic mercury. Using the ceramic reactor removal rates lower than 5 {mu}g/m{sup 3} [STP] of gaseous mercury and its compounds can be achieved. The ceramic reactor is active, regenerable and stable for a long term operation. 4 refs., 7 figs.

  19. Method of arsenic removal from water

    DOE Patents [OSTI]

    Gadgil, Ashok (El Cerrito, CA)

    2010-10-26

    A method for low-cost arsenic removal from drinking water using chemically prepared bottom ash pre-treated with ferrous sulfate and then sodium hydroxide. Deposits on the surface of particles of bottom ash form of activated iron adsorbent with a high affinity for arsenic. In laboratory tests, a miniscule 5 grams of pre-treated bottom ash was sufficient to remove the arsenic from 2 liters of 2400 ppb (parts per billion) arsenic-laden water to a level below 50 ppb (the present United States Environmental Protection Agency limit). By increasing the amount of pre-treated bottom ash, even lower levels of post-treatment arsenic are expected. It is further expected that this invention supplies a very low-cost solution to arsenic poisoning for large population segments.

  20. Metathesis depolymerization for removable surfactant templates.

    SciTech Connect (OSTI)

    Zifer, Thomas (Sandia National Laboratories, Livermore, CA); Wheeler, David Roger; Rahimian, Kamayar; McElhanon, James Ross (Sandia National Laboratories, Livermore, CA); Long, Timothy Michael; Jamison, Gregory Marks; Loy, Douglas Anson (Los Alamos National Laboratories, Los Alamos, NM); Kline, Steven R. (National Institute of Standards and Technology, Gaithersburg, MD); Simmons, Blake Alexander (Sandia National Laboratories, Livermore, CA)

    2005-03-01

    Current methodologies for the production of meso- and nanoporous materials include the use of a surfactant to produce a self-assembled template around which the material is formed. However, post-production surfactant removal often requires centrifugation, calcination, and/or solvent washing which can damage the initially formed material architecture(s). Surfactants that can be disassembled into easily removable fragments following material preparation would minimize processing damage to the material structure, facilitating formation of templated hybrid architectures. Herein, we describe the design and synthesis of novel cationic and anionic surfactants with regularly spaced unsaturation in their hydrophobic hydrocarbon tails and the first application of ring closing metathesis depolymerization to surfactant degradation resulting in the mild, facile decomposition of these new compounds to produce relatively volatile nonsurface active remnants.

  1. Removal of copper from ferrous scrap

    DOE Patents [OSTI]

    Blander, M.; Sinha, S.N.

    1987-07-30

    A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

  2. REMOVAL OF LEGACY PLUTONIUM MATERIALS FROM SWEDEN

    SciTech Connect (OSTI)

    Dunn, Kerry A.; Bellamy, J. Steve; Chandler, Greg T.; Iyer, Natraj C.; Koenig, Rich E.; Leduc, D.; Hackney, B.; Leduc, Dan R.

    2013-08-18

    U.S. Department of Energy’s National Nuclear Security Administration (NNSA) Office of Global Threat Reduction (GTRI) recently removed legacy plutonium materials from Sweden in collaboration with AB SVAFO, Sweden. This paper details the activities undertaken through the U.S. receiving site (Savannah River Site (SRS)) to support the characterization, stabilization, packaging and removal of legacy plutonium materials from Sweden in 2012. This effort was undertaken as part of GTRI’s Gap Materials Program and culminated with the successful removal of plutonium from Sweden as announced at the 2012 Nuclear Security Summit. The removal and shipment of plutonium materials to the United States was the first of its kind under NNSA’s Global Threat Reduction Initiative. The Environmental Assessment for the U.S. receipt of gap plutonium material was approved in May 2010. Since then, the multi-year process yielded many first time accomplishments associated with plutonium packaging and transport activities including the application of the of DOE-STD-3013 stabilization requirements to treat plutonium materials outside the U.S., the development of an acceptance criteria for receipt of plutonium from a foreign country, the development and application of a versatile process flow sheet for the packaging of legacy plutonium materials, the identification of a plutonium container configuration, the first international certificate validation of the 9975 shipping package and the first intercontinental shipment using the 9975 shipping package. This paper will detail the technical considerations in developing the packaging process flow sheet, defining the key elements of the flow sheet and its implementation, determining the criteria used in the selection of the transport package, developing the technical basis for the package certificate amendment and the reviews with multiple licensing authorities and most importantly integrating the technical activities with the Swedish partners.

  3. Removal of copper from ferrous scrap

    DOE Patents [OSTI]

    Blander, Milton (12833 S. 82nd Ct., Palos Park, IL 60464); Sinha, Shome N. (5748 Drexel, 2A, Chicago, IL 60637)

    1990-01-01

    A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

  4. Process for removing mercury from aqueous solutions

    DOE Patents [OSTI]

    Googin, J.M.; Napier, J.M.; Makarewicz, M.A.; Meredith, P.F.

    1985-03-04

    A process for removing mercury from water to a level not greater than two parts per billion wherein an anion exchange material that is insoluble in water is contacted first with a sulfide containing compound and second with a compound containing a bivalent metal ion forming an insoluble metal sulfide. To this treated exchange material is contacted water containing mercury. The water containing not more than two parts per billion of mercury is separated from the exchange material.

  5. Process for removing sulfur from coal

    DOE Patents [OSTI]

    Aida, T.; Squires, T.G.; Venier, C.G.

    1983-08-11

    A process is disclosed for the removal of divalent organic and inorganic sulfur compounds from coal and other carbonaceous material. A slurry of pulverized carbonaceous material is contacted with an electrophilic oxidant which selectively oxidizes the divalent organic and inorganic compounds to trivalent and tetravalent compounds. The carbonaceous material is then contacted with a molten caustic which dissolves the oxidized sulfur compounds away from the hydrocarbon matrix.

  6. Removal of copper from ferrous scrap

    DOE Patents [OSTI]

    Blander, M.; Sinha, S.N.

    1990-05-15

    A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

  7. Growing Up in Scotland: The Impact of Children's Early Activities on Cognitive Development - Summary Report 

    E-Print Network [OSTI]

    Government, Scottish

    2009-03-18

    This report uses data from the first three waves of the Growing Up in Scotland study (GUS) to explore differences in children’s cognitive ability.

  8. Growing Up in Scotland: Sweep 2 - Experiences of Pre-School Education 

    E-Print Network [OSTI]

    Government, Scottish

    2008-02-18

    Research findings (of four) accompanying the full research report on Sweep 2 findings of the Growing Up in Scotland study Year 2.

  9. Extending the Growing Season Workshop Registration Form. Preregister by Wednesday, March 5, 2014.

    E-Print Network [OSTI]

    Amin, S. Massoud

    the Growing Season Workshop Wednesday, March 12, 2014 from 9:00 to 2:30 ChuckDahn 1804Broadway Emmetsburg

  10. Math Play : growing and developing mathematics understanding in an emergent play-based environment

    E-Print Network [OSTI]

    DeGroot, Kendra

    2012-01-01

    objects Playing games using math reasoning Recognizing andobjects Playing games using math reasoning Recognizing andOF CALIFORNIA, SAN DIEGO Math Play: Growing and developing

  11. Removing nuclear waste, one shipment at a time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Removing nuclear waste, one shipment at a time Removing nuclear waste, one shipment at a time The Lab's 1,000th shipment of transuranic waste recently left Los Alamos, on its way...

  12. Identifying and removing sources of imprecision in polynomial regression

    E-Print Network [OSTI]

    Brauner, Neima

    Identifying and removing sources of imprecision in polynomial regression Neima Braunera and removal of imprecision in polynomial regression, originating from random errors (noise) in the independent.V. Keywords: Regression; Polynomial; Precision; Noise; Collinearity 1. Introduction Mathematical modeling

  13. Process for removing technetium from iron and other metals

    DOE Patents [OSTI]

    Leitnaker, J.M.; Trowbridge, L.D.

    1999-03-23

    A process for removing technetium from iron and other metals comprises the steps of converting the molten, alloyed technetium to a sulfide dissolved in manganese sulfide, and removing the sulfide from the molten metal as a slag. 4 figs.

  14. Modeling and simulation of material removal with particulate flows

    E-Print Network [OSTI]

    Arbelaez, D; Zohdi, T I; Dornfeld, David

    2008-01-01

    optimization In material removal processes there are a large number of input parameters which control the quality of the process.

  15. Method for removing fluoride contamination from nitric acid

    DOE Patents [OSTI]

    Pruett, David J. (Knoxville, TN); Howerton, William B. (Kingston, TN)

    1982-01-01

    Fluoride ions are removed from nitric acid solution by contacting the vaporized solution with alumina or zirconium.

  16. Method for the removal of carbonyl sulfide from liquid propane

    SciTech Connect (OSTI)

    McClure, G.

    1980-06-17

    A method for the removal of carbonyl sulfide from liquid propane under liquid-liquid contact conditions by mixing liquid propane containing carbonyl sulfide as an impurity with 2-(2-aminoethoxy) ethanol as the principal agent for the carbonyl sulfide removal. The 2(2-aminoethoxy) ethanol is reclaimed and reused for further carbonyl sulfide removal. 5 claims.

  17. INVESTIGATION OF IONIC CONTAMINATION REMOVAL FROM SILICON DIOXIDE SURFACES

    E-Print Network [OSTI]

    Suni, Ian Ivar

    INVESTIGATION OF IONIC CONTAMINATION REMOVAL FROM SILICON DIOXIDE SURFACES H. Lin, A. A. Busnaina, and I. I. Suni T he removal of ionic contaminants from silicon surfaces surface contamination level canM Communications L td. INTRODUCTION with increasing frequency and power, and decreases Contamination removal is one

  18. BOA: Pipe asbestos insulation removal robot system

    SciTech Connect (OSTI)

    Schempf, H.; Bares, J.; Schnorr, W. [and others

    1995-12-31

    The BOA system is a mobile pipe-external robotic crawler used to remotely strip and bag asbestos-containing lagging and insulation materials (ACLIM) from various diameter pipes in (primarily) industrial installations. Steam and process lines within the DOE weapons complex warrant the use of a remote device due to the high labor costs and high level of radioactive contamination, making manual removal extremely costly and highly inefficient. Currently targeted facilities for demonstration and remediation are Fernald in Ohio and Oak Ridge in Tennessee.

  19. Ultracapacitor having residual water removed under vacuum

    DOE Patents [OSTI]

    Wei, Chang (Niskayuna, NY); Jerabek, Elihu Calvin (Glenmont, NY); Day, James (Scotia, NY)

    2002-10-15

    A multilayer cell is provided that comprises two solid, nonporous current collectors, two porous electrodes separating the current collectors, a porous separator between the electrodes and an electrolyte occupying pores in the electrodes and separator. The mutilayer cell is electrolyzed to disassociate water within the cell to oxygen gas and hydrogen gas. A vacuum is applied to the cell substantially at the same time as the electrolyzing step, to remove the oxygen gas and hydrogen gas. The cell is then sealed to form a ultracapacitor substantially free from water.

  20. Mechanism of paint removing by organic solvents

    SciTech Connect (OSTI)

    Del Nero, V.; Siat, C.; Marti, M.J.; Aubry, J.M.; Lallier, J.P.; Dupuy, N.; Huvenne, J.P.

    1996-01-01

    The mechanism of paint removing has been studied by comparing the stripping efficiency of a given solvent with its ability to swell the film. The most effective solvents have a Hildebrand{close_quote}s parameter, {delta}{sub H}, ranging from 10.5 to 12 and a Dimroth parameter, ET{sub (30)}, ranging from 0.25 to 0.4. The synergy observed with the mixtures DMSO/non polar solvent is explained by a dissociation of the DMSO clusters into individual molecules which diffuse more easily. {copyright} {ital 1996 American Institute of Physics.}

  1. Protection #2: Trap and Remove Sediment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeedingProgramExemptions |(Conference)ProjectProposedAmerica'sTrap and Remove

  2. Keeler-Pennwalt Wood Pole Removal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would likeUniverseIMPACTThousand Cubic Feet) Sold toKeeler-Pennwalt-Wood-Pole-Removal Sign

  3. The response of venation networks in growing leaves to external mechanical stress

    E-Print Network [OSTI]

    Adda-Bedia, Mokhtar

    The response of venation networks in growing leaves to external mechanical stress Yohai Bar-Sinai1 the coupling between vein patterns and growth. We first model the mechanics of a growing vascular network and study its response to external mechanical stress. We use the so-called texture tensor to quantify

  4. Growing Artificial Societies: Social Science from the Bottom Up. By Joshua M. Epstein and Robert Axtell.

    E-Print Network [OSTI]

    Tesfatsion, Leigh

    Growing Artificial Societies: Social Science from the Bottom Up. By Joshua M. Epstein and Robert be passed in modified form to descendants. Such an artificial society can grow itself over time, with large) and a vision level that helps it search for sugar. Any sugar collected by an agent in excess of its metabolic

  5. TYPE A VERIFICATION FOR THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PHASE 2 DF WASTE LINE REMOVAL, BNL

    SciTech Connect (OSTI)

    P.C. Weaver

    2010-07-09

    5098-SR-02-0 PROJECT-SPECIFIC TYPE A VERIFICATION FOR THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PHASE 2 DF WASTE LINE REMOVAL, BROOKHAVEN NATIONAL LABORATORY

  6. Saeltzer Dam Removal on Clear Creek 11 years later: An assessment of upstream channel changes since the dam's removal

    E-Print Network [OSTI]

    Simons, Crystal; Walker, Katelyn; Zimring, Mark

    2011-01-01

    Boulder BLDR Bedrock BDRK Dam Rubble DMRB Table B1. 2011pages. Brown, M. (n.d. ). Clear Creek—McCormick-Saeltzer DamRemoval: Dam removal re-opens spring run salmon habitat. US

  7. Removal of arsenic compounds from petroliferous liquids

    DOE Patents [OSTI]

    Fish, R.H.

    1984-04-06

    The present invention in one aspect comprises a process for removing arsenic from petroliferous-derived liquids by contacting said liquid with a divinylbenzene-crosslinked polystyrene polymer (i.e. PS-DVB) having catechol ligands anchored to said polymer, said contacting being at an elevated temperature. In another aspect, the invention is a process for regenerating spent catecholated polystyrene polymer by removal of the arsenic bound to it from contacting petroliferous liquid in accordance with the aspect described above which regenerating process comprises: (a) treating said spent catecholated polystyrene polymer with an aqueous solution of at least one member selected from the group consisting of carbonates and bicarbonates of ammonium, alkali metals, and alkaline earth metals, said solution having a pH between about 8 and 10, and said treating being at a temperature in the range of about 20/sup 0/ to 100/sup 0/C; (b) separating the solids and liquids from each other. In a preferred embodiment the regeneration treatment is in two steps wherein step: (a) is carried out with an aqueous alcoholic carbonate solution which includes at least one lower alkyl alcohol, and, steps (c) and (d) are added. Steps (c) and (d) comprise: (c) treating the solids with an aqueous alcoholic solution of at least one ammonium, alkali or alkaline earth metal bicarbonate at a temperature in the range of about 20 to 100/sup 0/C; and (d) separating the solids from the liquids.

  8. Drum ring removal/installation tool

    DOE Patents [OSTI]

    Andrade, William Andrew (Livermore, CA)

    2006-11-14

    A handheld tool, or a pair of such tools, such as for use in removing/installing a bolt-type clamping ring on a container barrel/drum, where the clamping ring has a pair of clamping ends each with a throughbore. Each tool has an elongated handle and an elongated lever arm transversely connected to one end of the handle. The lever arm is capable of being inserted into the throughbore of a selected clamping end and leveraged with the handle to exert a first moment on the selected clamping end. Each tool also has a second lever arm, such as a socket with an open-ended slot, which is suspended alongside the first lever arm. The second lever arm is capable of engaging the selected clamping end and being leveraged with the handle to exert a second moment which is orthogonal to the first moment. In this manner, the first and second moments operate to hold the selected clamping end fixed relative to the tool so that the selected clamping end may be controlled with the handle. The pair of clamping ends may also be simultaneously and independently controlled with the use of two handles/tools so as to contort the geometry of the drum clamping ring and enable its removal/installation.

  9. Process for removing polychlorinated biphenyls from soil

    DOE Patents [OSTI]

    Hancher, C.W.; Saunders, M.B.; Googin, J.M.

    1984-11-16

    The present invention relates to a method of removing polychlorinated biphenyls from soil. The polychlorinated biphenyls are extracted from the soil by employing a liquid organic solvent dispersed in water in the ratio of about 1:3 to 3:1. The organic solvent includes such materials as short-chain hydrocarbons including kerosene or gasoline which are immiscible with water and are nonpolar. The organic solvent has a greater affinity for the PCB's than the soil so as to extract the PCB's from the soil upon contact. The organic solvent phase is separated from the suspended soil and water phase and distilled for permitting the recycle of the organic solvent phase and the concentration of the PCB's in the remaining organic phase. The present process can be satisfactorily practiced with soil containing 10 to 20% petroleum-based oils and organic fluids such as used in transformers and cutting fluids, coolants and the like which contain PCB's. The subject method provides for the removal of a sufficient concentration of PCB's from the soil to provide the soil with a level of PCB's within the guidelines of the Environmental Protection Agency.

  10. EVOLVING EXPECTATIONS OF DAM REMOVAL OUTCOMES: DOWNSTREAM GEOMORPHIC EFFECTS FOLLOWING REMOVAL OF A SMALL, GRAVEL-FILLED DAM1

    E-Print Network [OSTI]

    Tullos, Desiree

    EVOLVING EXPECTATIONS OF DAM REMOVAL OUTCOMES: DOWNSTREAM GEOMORPHIC EFFECTS FOLLOWING REMOVAL OF A SMALL, GRAVEL-FILLED DAM1 Kelly Kibler, Desiree Tullos, and Mathias Kondolf 2 ABSTRACT: Dam removal is a promising river restoration technique, particularly for the vast number of rivers impounded by small dams

  11. Removal of Sarin Aerosol and Vapor by Water Sprays

    SciTech Connect (OSTI)

    Brockmann, John E.

    1998-09-01

    Falling water drops can collect particles and soluble or reactive vapor from the gas through which they fall. Rain is known to remove particles and vapors by the process of rainout. Water sprays can be used to remove radioactive aerosol from the atmosphere of a nuclear reactor containment building. There is a potential for water sprays to be used as a mitigation technique to remove chemical or bio- logical agents from the air. This paper is a quick-look at water spray removal. It is not definitive but rather provides a reasonable basic model for particle and gas removal and presents an example calcu- lation of sarin removal from a BART station. This work ~ a starting point and the results indicate that further modeling and exploration of additional mechanisms for particle and vapor removal may prove beneficial.

  12. Resonant Removal of Exomoons During Planetary Migration

    E-Print Network [OSTI]

    Spalding, Christopher; Adams, Fred C

    2015-01-01

    Jupiter and Saturn play host to an impressive array of satellites, making it reasonable to suspect that similar systems of moons might exist around giant extrasolar planets. Furthermore, a significant population of such planets is known to reside at distances of several Astronomical Units (AU), leading to speculation that some moons thereof might support liquid water on their surfaces. However, giant planets are thought to undergo inward migration within their natal protoplanetary disks, suggesting that gas giants currently occupying their host star's habitable zone formed further out. Here we show that when a moon-hosting planet undergoes inward migration, dynamical interactions may naturally destroy the moon through capture into a so-called "evection resonance." Within this resonance, the lunar orbit's eccentricity grows until the moon eventually collides with the planet. Our work suggests that moons orbiting within about 10 planetary radii are susceptible to this mechanism, with the exact number dependent ...

  13. IMPROVED PROCESSES TO REMOVE NAPHTHENIC ACIDS

    SciTech Connect (OSTI)

    Aihua Zhang; Qisheng Ma; William A. Goddard; Yongchun Tang

    2004-04-28

    In the first year of this project, we have established our experimental and theoretical methodologies for studies of the catalytic decarboxylation process. We have developed both glass and stainless steel micro batch type reactors for the fast screening of various catalysts with reaction substrates of model carboxylic acid compounds and crude oil samples. We also developed novel product analysis methods such as GC analyses for organic acids and gaseous products; and TAN measurements for crude oil. Our research revealed the effectiveness of several solid catalysts such as NA-Cat-1 and NA-Cat-2 for the catalytic decarboxylation of model compounds; and NA-Cat-5{approx}NA-Cat-9 for the acid removal from crude oil. Our theoretical calculations propose a three-step concerted oxidative decarboxylation mechanism for the NA-Cat-1 catalyst.

  14. Removing sulphur oxides from a fluid stream

    DOE Patents [OSTI]

    Katz, Torsten; Riemann, Christian; Bartling, Karsten; Rigby, Sean Taylor; Coleman, Luke James Ivor; Lail, Marty Alan

    2014-04-08

    A process for removing sulphur oxides from a fluid stream, such as flue gas, comprising: providing a non-aqueous absorption liquid containing at least one hydrophobic amine, the liquid being incompletely miscible with water; treating the fluid stream in an absorption zone with the non-aqueous absorption liquid to transfer at least part of the sulphur oxides into the non-aqueous absorption liquid and to form a sulphur oxide-hydrophobic amine-complex; causing the non-aqueous absorption liquid to be in liquid-liquid contact with an aqueous liquid whereby at least part of the sulphur oxide-hydrophobic amine-complex is hydrolyzed to release the hydrophobic amine and sulphurous hydrolysis products, and at least part of the sulphurous hydrolysis products is transferred into the aqueous liquid; separating the aqueous liquid from the non-aqueous absorption liquid. The process mitigates absorbent degradation problems caused by sulphur dioxide and oxygen in flue gas.

  15. The HMDS Coating Flaw Removal Tool

    SciTech Connect (OSTI)

    Monticelli, M V; Nostrand, M C; Mehta, N; Kegelmeyer, L; Johnson, M A; Fair, J; Widmayer, C

    2008-10-24

    In many high energy laser systems, optics with HMDS sol gel antireflective coatings are placed in close proximity to each other making them particularly susceptible to certain types of strong optical interactions. During the coating process, halo shaped coating flaws develop around surface digs and particles. Depending on the shape and size of the flaw, the extent of laser light intensity modulation and consequent probability of damaging downstream optics may increase significantly. To prevent these defects from causing damage, a coating flaw removal tool was developed that deploys a spot of decane with a syringe and dissolves away the coating flaw. The residual liquid is evacuated leaving an uncoated circular spot approximately 1mm in diameter. The resulting uncoated region causes little light intensity modulation and thus has a low probability of causing damage in optics downstream from the mitigated flaw site.

  16. AX Tank Farm tank removal study

    SciTech Connect (OSTI)

    SKELLY, W.A.

    1999-02-24

    This report examines the feasibility of remediating ancillary equipment associated with the 241-AX Tank Farm at the Hanford Site. Ancillary equipment includes surface structures and equipment, process waste piping, ventilation components, wells, and pits, boxes, sumps, and tanks used to make waste transfers to/from the AX tanks and adjoining tank farms. Two remedial alternatives are considered: (1) excavation and removal of all ancillary equipment items, and (2) in-situ stabilization by grout filling, the 241-AX Tank Farm is being employed as a strawman in engineering studies evaluating clean and landfill closure options for Hanford single-shell tanks. This is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms.

  17. AX Tank Farm tank removal study

    SciTech Connect (OSTI)

    SKELLY, W.A.

    1998-10-14

    This report considers the feasibility of exposing, demolishing, and removing underground storage tanks from the 241-AX Tank Farm at the Hanford Site. For the study, it was assumed that the tanks would each contain 360 ft{sup 3} of residual waste (corresponding to the one percent residual Inventory target cited in the Tri-Party Agreement) at the time of demolition. The 241-AX Tank Farm is being employed as a ''strawman'' in engineering studies evaluating clean and landfill closure options for Hanford single-shell tank farms. The report is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms.

  18. High SO2 Removal Efficiency Testing

    SciTech Connect (OSTI)

    Gary Blythe

    1997-02-12

    This document provides a discussion of the technical progress on DOE/PETC project number DE-AC22-92PC91338, "High Efficiency SO Removal Testing," for 2 the time period 1 October through 31 December 1996. The project involves testing at six full-scale utility flue gas desulfurization (FGD) systems, to evaluate low capital cost upgrades that may allow these systems to achieve up to 98% SO removal efficiency. The upgrades being 2 evaluated mostly involve using performance additives in the FGD systems. The "base" project involved testing at the Tampa Electric Company?s Big Bend Station. All five potential options to the base program have been exercised by DOE, involving testing at Hoosier Energy?s Merom Station (Option I), Southwestern Electric Power Company?s Pirkey Station (Option II), PSI Energy?s Gibson Station (Option III), Duquesne Light?s Elrama Station (Option IV), and New York State Electric and Gas Corporation?s Kintigh Station (Option V). The originally planned testing has been completed for all six sites. However, additional testing has been planned at the Big Bend Station, and that testing commenced during the current quarter. The remainder of this document is divided into four sections. Section 2, Project Summary, provides a brief overview of the status of technical efforts on this project. Section 3, Results, summarizes the outcome from technical efforts during the quarter, or results from prior quarters that have not been previously reported. In Section 4, Plans for the Next Reporting Period, an overview is provided of the technical efforts that are anticipated for the first quarter of calendar year 1996. Section 5 contains a brief acknowledgment.

  19. High SO2 Removal Efficiency Testing

    SciTech Connect (OSTI)

    Gary Blythe

    1997-04-23

    This document provides a discussion of the technical progress on DOE/PETC project number DE-AC22-92PC91338, "High Efficiency SO2 Removal Testing", for the time period 1 January through 31 March 1997. The project involves testing at six full-scale utility flue gas desulfurization (FGD) systems, to evaluate low capital cost upgrades that may allow these systems to achieve up to 98% SO2 removal efficiency. The upgrades being evaluated mostly involve using performance additives in the FGD systems. The "base" project involved testing at the Tampa Electric Company?s Big Bend Station. All five potential options to the base program have been exercised by DOE, involving testing at Hoosier Energy?s Merom Station (Option I), Southwestern Electric Power Company?s Pirkey Station (Option II), PSI Energy?s Gibson Station (Option III), Duquesne Light?s Elrama Station (Option IV), and New York State Electric and Gas Corporation?s (NYSEG) Kintigh Station (Option V). The originally planned testing has been completed for all six sites. However, additional testing is planned at the Big Bend Station. The remainder of this document is divided into four sections. Section 2, Project Summary, provides a brief overview of the status of technical efforts on this project. Section 3, Results, summarizes the outcome from technical efforts during the quarter, or results from prior quarters that have not been previously reported. In Section 4, Plans for the Next Reporting Period, an overview is provided of the technical efforts that are anticipated for the second quarter of calendar year 1997. Section 5 contains a brief acknowledgement.

  20. High SO2 Removal Efficiency Testing

    SciTech Connect (OSTI)

    Gary Blythe

    1997-07-29

    This document provides a discussion of the technical progress on DOE/PETC project number DE-AC22-92PC91338, "High Efficiency SO2 Removal Testing", for the time period 1 April through 30 June 1997. The project involves testing at six full-scale utility flue gas desulfurization (FGD) systems to evaluate low capital cost upgrades that may allow these systems to achieve up to 98% SO2 removal efficiency. The upgrades being evaluated mostly involve using performance additives in the FGD systems. The "base" project involved testing at the Tampa Electric Company?s Big Bend Station. All five potential options to the base program have been exercised by DOE, involving testing at Hoosier Energy?s Merom Station (Option I), Southwestern Electric Power Company?s Pirkey Station (Option II), PSI Energy?s Gibson Station (Option III), Duquesne Light?s Elrama Station (Option IV), and New York State Electric and Gas Corporation?s Kintigh Station (Option V). The originally planned testing has been completed for all six sites. However, additional testing is being conducted at the Big Bend Station. The remainder of this document is divided into four sections. Section 2, Project Summary, provides a brief overview of the status of technical efforts on this project. Section 3, Results, summarizes the outcome from technical efforts during the quarter, or results from prior quarters that have not been previously reported. In Section 4, Plans for the Next Reporting Period, an overview is provided of the technical efforts that are anticipated for the third quarter of calendar year 1997. Section 5 contains a brief acknowledgment.

  1. Entrapment of Guide Wire in an Inferior Vena Cava Filter: A Technique for Removal

    SciTech Connect (OSTI)

    Abdel-Aal, Ahmed Kamel Saddekni, Souheil; Hamed, Maysoon Farouk; Fitzpatrick, Farley

    2013-04-15

    Entrapment of a central venous catheter (CVC) guide wire in an inferior vena cava (IVC) filter is a rare, but reported complication during CVC placement. With the increasing use of vena cava filters (VCFs), this number will most likely continue to grow. The consequences of this complication can be serious, as continued traction upon the guide wire may result in filter dislodgement and migration, filter fracture, or injury to the IVC. We describe a case in which a J-tipped guide wire introduced through a left subclavian access without fluoroscopic guidance during CVC placement was entrapped at the apex of an IVC filter. We describe a technique that we used successfully in removing the entrapped wire through the left subclavian access site. We also present simple useful recommendations to prevent this complication.

  2. Growing Green Environmental stewardship is a complex issue that engages governments,

    E-Print Network [OSTI]

    Lennard, William N.

    Growing Green Environmental stewardship is a complex issue that engages governments, academics, practitioners, non-profit organizations and companies. Corporations are sizeable players in this global and environmental responsibility · Helps companies acknowledge sustainable business practices ­ which can mean many

  3. Growing Up in Scotland: Year 3 - The Impact of Children's Early Activities of Cognitive Development 

    E-Print Network [OSTI]

    Bradshaw, Paul; Wasoff, Fran

    2009-03-18

    The Growing Up in Scotland study (GUS) is an important longitudinal research project aimed at tracking the lives of a cohort of Scottish children from the early years, through childhood and beyond. The study is funded by ...

  4. Sources of biological variation in residual feed intake in growing and finishing steers 

    E-Print Network [OSTI]

    Brown, Erin Gwen

    2006-04-12

    Objectives of this research were to characterize residual feed intake (RFI) in growing and finishing steers and examine phenotypic correlations between performance, feed efficiency, carcass, digestib ility, and physiological indicator traits...

  5. Evaluation of a mathematical model in predicting intake of growing and finishing cattle 

    E-Print Network [OSTI]

    Bourg, Brandi Marie

    2009-05-15

    energy (ME) value was conducted. A meta-analysis of growing and finishing steers evaluated to model’s accuracy in predicting DMR of individually fed steers, and the relationships between several model-predicted variables and actual performance...

  6. Re-evaluation of the Vitamin D3 Requirement for Growing Chickens 

    E-Print Network [OSTI]

    Leyva Jimenez, Hector Enrique

    2015-07-24

    Three experiments were conducted with the purpose of re-evaluating the vitamin D3 requirement of growing chickens. Due to intense genetic selection in the poultry industry, it is probable that modern strains have altered ...

  7. Growing minds: evaluating the effects of gardening on quality of life and obesity in older adults 

    E-Print Network [OSTI]

    Lillard, Aime Jo Sommerfeld

    2009-05-15

    Older adults represent a growing part of the population of the United States. Due to decreased physical activity, dietary changes, and alterations in metabolic rate this population is susceptible to an increased rate of diseases. The generation...

  8. Timing and duration of European larch growing season along altitudinal gradients in the Swiss Alps

    E-Print Network [OSTI]

    Esper, Jan

    and matura- tion of the stem wood. Needles appeared ~3­4 weeks earlier than stem growth. The duration of ring growth throughout the entire growing season. Exceptions include a limited number of stud- ies that showed

  9. Growing Up In Scotland Study: GUS Exploring The Experience and Outcomes For Advantaged and Disadvantaged Families 

    E-Print Network [OSTI]

    Bradshaw, Paul; Martin, Claudia; Cunningham-Burley, Sarah

    2008-03-12

    This report draws on data from the first sweep of the Growing Up in Scotland ( GUS) study. The Sweep 1 Report highlighted the persistence of inequalities between advantaged and disadvantaged families which impact on parents ...

  10. Using RPS Policies to Grow the Solar Market in the United States

    E-Print Network [OSTI]

    Wiser, Ryan H

    2008-01-01

    RPS policies to grow the solar market in the United StatesCalifornia is not the only market for solar in the US; otherthe long-term, the largest markets for solar electricity are

  11. Building community assets through individual development accounts : growing a strategic network in Lawrence, Massachusetts

    E-Print Network [OSTI]

    Wu, Cindy C. (Cindy Cin-Wei)

    2007-01-01

    This thesis aims to inform the decision-making process for growing an asset-building program through strategic partnerships with other community-based organizations (CBOs). The impetus for this paper came from Lawrence ...

  12. Asian Greens Offer Tasty, Easy-to-Grow Source of Nutrition

    E-Print Network [OSTI]

    Martin, Orin

    2008-01-01

    leafy vegetables. They offer nutritious dark greens high inAnd at full maturity, they offer an amazing amount of high-UC Santa Cruz Asian Greens Offer Tasty, Easy-to-Grow Source

  13. For Immediate Release --Monday, March 30, 2015 Growing global phenomenon of atomic tourism sparks

    E-Print Network [OSTI]

    Morris, Joy

    was introduced to the devastating power of an atomic bomb, and as the anniversary phenomenon of atomic tourism sparks unique research project by U of L professor on a unique project that examines the growing global phenomenon of atomic tourism

  14. Growing Up in Scotland: Sources of Formal and Informal Support for Parents of Young Children 

    E-Print Network [OSTI]

    Government, Scottish

    2007-01-08

    The Growing Up in Scotland study ( GUS) is an important new longitudinal research project aimed at tracking the lives of a cohort of Scottish children from the early years, through childhood and beyond. Its principal aim ...

  15. LIMITS FOR QUEUES AS THE WAITING ROOM GROWS Daniel P. Heyman Ward Whitt

    E-Print Network [OSTI]

    Whitt, Ward

    LIMITS FOR QUEUES AS THE WAITING ROOM GROWS by Daniel P. Heyman Ward Whitt Bell Communications Research AT&T Bell Laboratories Red Bank, NJ 07701 Murray Hill, NJ 07974 May 11, 1988 #12;ABSTRACT We study

  16. LIMITS FOR QUEUES AS THE WAITING ROOM GROWS Daniel P. Heyman Ward Whitt

    E-Print Network [OSTI]

    Whitt, Ward

    LIMITS FOR QUEUES AS THE WAITING ROOM GROWS by Daniel P. Heyman Ward Whitt Bell Communications Research AT&T Bell Laboratories Red Bank, NJ 07701 Murray Hill, NJ 07974 May 11, 1988 #12; ABSTRACT We

  17. Growing machines

    E-Print Network [OSTI]

    Griffith, Saul Thomas, 1974-

    2004-01-01

    construction is developed in three dimensions. It is similarly shown that right-angled tetrahedrons, when folded from an edge-connected string, can generate any three dimensional structure where the primitive pixel (or ...

  18. Growing smarter 

    E-Print Network [OSTI]

    Swyden, Courtney

    2007-01-01

    water use that residents can implement around the home such as raising the height of lawn mower blades and using soaker hoses, as well as swimming pool tips and explanations on how to read water bills. EnviroMedia originally conducted statewide research... to prevent evaporation and keep soil moist. ? Choose ?water wise? or native Texas plants such as lantana, salvia and Mexican sage. ? Raise your lawn mower blade and cut grass to a height of 3 inches?this shades the soil, which reduces evaporation...

  19. Metal Cutting for Large Component Removal

    SciTech Connect (OSTI)

    Hulick, Robert M.

    2008-01-15

    Decommissioning of commercial nuclear power plants presents technological challenges. One major challenge is the removal of large components mainly consisting of the reactor vessel, steam generators and pressurizer. In order to remove and package these large components nozzles must be cut from the reactor vessel to precise tolerances. In some cases steam generators must be segmented for size and weight reduction. One innovative technology that has been used successfully at several commercial nuclear plant decommissioning is diamond wire sawing. Diamond wire sawing is performed by rotating a cable with diamond segments attached using a flywheel approximately 24 inches in diameter driven remotely by a hydraulic pump. Tension is provided using a gear rack drive which also takes up the slack in the wire. The wire is guided through the use of pulleys keeps the wire in a precise location. The diamond wire consists of 1/4 inch aircraft cable with diamond beads strung over the cable separated by springs and brass crimps. Standard wire contains 40 diamond beads per meter and can be made to any length. Cooling the wire and controlling the spread of contamination presents significant challenges. Under normal circumstances the wire is cooled and the cutting kerf cleaned by using water. In some cases of reactor nozzle cuts the use of water is prohibited because it cannot be controlled. This challenge was solved by using liquid Carbon Dioxide as the cooling agent. The liquid CO{sub 2} is passed through a special nozzle which atomizes the liquid into snowflakes which is introduced under pressure to the wire. The snowflakes attach to the wire keeping it cool and to the metal shavings. As the CO{sub 2} and metal shavings are released from the wire due to its fast rotation, the snowflakes evaporate leaving only the fine metal shavings as waste. Secondary waste produced is simply the small volume of fine metal shavings removed from the cut surface. Diamond wire sawing using CO{sub 2} cooling has been employed for cutting the reactor nozzles at San Onofre Unit 1 and at Connecticut Yankee. These carbon steel nozzles ranged up to 54 inch diameter with a 15 inch thick wall and an interior stainless cladding. Diamond wire sawing using traditional water cooling has been used to segment the reactor head at Rancho Seco and for cutting reactor nozzles and control rod drive tubes at Dairyland Power's Lacrosse BWR project. Advantages: - ALARA: All cutting is preformed remotely significantly reducing dose. Stringing of wires is accomplished using long handle tools. - Secondary waste is reduced to just the volume of material cut with the diamond wire. - The potential for airborne contamination is eliminated. Due to the flexibility of the wire, any access restrictions and interferences can be accommodated using pulleys and long handle tools. - The operation is quiet. Disadvantages: - With Liquid Carbon Dioxide cooling and cleaning, delivery of the material must be carefully planned. The longer the distance from the source to the cut area, the greater the chance for pressure drop and subsequent problems with line freezing. - Proper shrouding and ventilation are required for environmental reasons. In each case, the metal structures were cut at a precise location. Radiation dose was reduced significantly by operating the equipment from a remote location. The cuts were very smooth and completed on schedule. Each project must be analyzed individually and take into account many factors including access, radiological conditions, environmental conditions, schedule requirements, packaging requirements and size of cuts.

  20. Thiacrown polymers for removal of mercury from waste streams

    DOE Patents [OSTI]

    Baumann, Theodore F.; Reynolds, John G.; Fox, Glenn A.

    2004-02-24

    Thiacrown polymers immobilized to a polystyrene-divinylbenzene matrix react with Hg.sup.2+ under a variety of conditions to efficiently and selectively remove Hg.sup.2+ ions from acidic aqueous solutions, even in the presence of a variety of other metal ions. The mercury can be recovered and the polymer regenerated. This mercury removal method has utility in the treatment of industrial wastewater, where a selective and cost-effective removal process is required.

  1. Thiacrown polymers for removal of mercury from waste streams

    DOE Patents [OSTI]

    Baumann, Theodore F. (Tracy, CA); Reynolds, John G. (San Ramon, CA); Fox, Glenn A. (Livermore, CA)

    2002-01-01

    Thiacrown polymers immobilized to a polystyrene-divinylbenzene matrix react with Hg.sup.2+ under a variety of conditions to efficiently and selectively remove Hg.sup.2+ ions from acidic aqueous solutions, even in the presence of a variety of other metal ions. The mercury can be recovered and the polymer regenerated. This mercury removal method has utility in the treatment of industrial wastewater, where a selective and cost-effective removal process is required.

  2. Heat recirculating cooler for fluid stream pollutant removal

    DOE Patents [OSTI]

    Richards, George A. (Morgantown, WV); Berry, David A. (Morgantown, WV)

    2008-10-28

    A process by which heat is removed from a reactant fluid to reach the operating temperature of a known pollutant removal method and said heat is recirculated to raise the temperature of the product fluid. The process can be utilized whenever an intermediate step reaction requires a lower reaction temperature than the prior and next steps. The benefits of a heat-recirculating cooler include the ability to use known pollutant removal methods and increased thermal efficiency of the system.

  3. Removal of radioactive and other hazardous material from fluid waste

    DOE Patents [OSTI]

    Tranter, Troy J. (Idaho Falls, ID); Knecht, Dieter A. (Idaho Falls, ID); Todd, Terry A. (Aberdeen, ID); Burchfield, Larry A. (W. Richland, WA); Anshits, Alexander G. (Krasnoyarsk, RU); Vereshchagina, Tatiana (Krasnoyarsk, RU); Tretyakov, Alexander A. (Zheleznogorsk, RU); Aloy, Albert S. (St. Petersburg, RU); Sapozhnikova, Natalia V. (St. Petersburg, RU)

    2006-10-03

    Hollow glass microspheres obtained from fly ash (cenospheres) are impregnated with extractants/ion-exchangers and used to remove hazardous material from fluid waste. In a preferred embodiment the microsphere material is loaded with ammonium molybdophosphonate (AMP) and used to remove radioactive ions, such as cesium-137, from acidic liquid wastes. In another preferred embodiment, the microsphere material is loaded with octyl(phenyl)-N-N-diisobutyl-carbamoylmethylphosphine oxide (CMPO) and used to remove americium and plutonium from acidic liquid wastes.

  4. Y-12 Removes Nuclear Materials from Two Facilities to Reduce...

    National Nuclear Security Administration (NNSA)

    Removes Nuclear Materials from Two Facilities to Reduce Site's Nuclear Footprint (Alpha 5 and 9720-38 No Longer Designated as Nuclear Facilities) | National Nuclear Security...

  5. Treatment of Difficult Waters: Arsenic Removal Silica Control...

    Office of Scientific and Technical Information (OSTI)

    of Difficult Waters: Arsenic Removal Silica Control Carbon Capture and Enhanced Oil Recovery. Citation Details In-Document Search Title: Treatment of Difficult Waters:...

  6. Study of Alternative Approaches for Transite Panel Removal

    Broader source: Energy.gov [DOE]

    Bechtel Jacobs Company LLC (BJC) assembled an experienced team from both sites to evaluate both the manual and mechanical methods of transite panel removal.

  7. RADTRAD: A simplified model for RADionuclide Transport and Removal...

    Office of Scientific and Technical Information (OSTI)

    RADTRAD: A simplified model for RADionuclide Transport and Removal And Dose estimation Citation Details In-Document Search Title: RADTRAD: A simplified model for RADionuclide...

  8. Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown Sites Prepared for U.S. Department of Energy Nuclear Fuels Storage and Transportation Planning Project Steven J....

  9. United States, International Partners Remove Last Remaining Weapons...

    Broader source: Energy.gov (indexed) [DOE]

    are Austria, Chile, Czech Republic, Libya, Mexico, Romania, Serbia, Taiwan, Turkey, Ukraine, and Vietnam. To date, the Department has removed or dispositioned more than 5,000...

  10. Oregon Section 401 Removal/Fill Certification Webpage | Open...

    Open Energy Info (EERE)

    Certification Webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Oregon Section 401 RemovalFill Certification Webpage Abstract Provides overview...

  11. EGR Cooler Fouling- Visualization of Deposition and Removal Mechanis

    Broader source: Energy.gov [DOE]

    Presents experimental data on exhaust gas recirculation(EGR) cooler fouling using new test apparatus that allows for in-situ observation of deposition and removal processes

  12. Process to remove rare earth from IFR electrolyte

    DOE Patents [OSTI]

    Ackerman, J.P.; Johnson, T.R.

    1992-01-01

    The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner.

  13. EM Removes Radioactive Components from Former Reactor at Oak...

    Office of Environmental Management (EM)

    contractor employees who worked on the project to remove irradiated components from a reactor pool gather to watch the transport of the shipment offsite for disposition. Employees...

  14. Removal of Animal Antibiotics for Potable Water Reclamation: A Review

    E-Print Network [OSTI]

    Chang, Rita

    2015-01-01

    Treatment Primary treatment of wastewater usually involveswastewater. Removals of antibiotics in primary treatmentprimary clarifier effluents were taken from the Amherst, NY wastewater treatment

  15. Remove Condensate with Minimal Air Loss; Industrial Technologies...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3 * August 2004 Industrial Technologies Program Suggested Actions * Inspect the condensate traps and determine if they are operating properly. * Review your condensate removal...

  16. NNSA's Global Threat Reduction Initiative Removes More Than One...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Global Threat Reduction Initiative Removes More Than One Ton of Food | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the...

  17. Treatment of Difficult Waters: Arsenic Removal Silica Control...

    Office of Scientific and Technical Information (OSTI)

    of Difficult Waters: Arsenic Removal Silica Control Carbon Capture and Enhanced Oil Recovery. Brady, Patrick Vane Abstract not provided. Sandia National Laboratories...

  18. Method of removal of sulfur from coal and petroleum products

    DOE Patents [OSTI]

    Verkade, John G. (Ames, IA); Mohan, Thyagarajan (Ames, IA); Angelici, Robert J. (Ames, IA)

    1995-01-01

    A method for the removal of sulfur from sulfur-bearing materials such as coal and petroleum products using organophosphine and organophosphite compounds is provided.

  19. More Economical Sulfur Removal for Fuel Processing Plants

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    crude oil it is present in sulfur-containing organic compounds which are converted into hydrocarbons and H 2 S during the removal process (hydrodesulfurization). In both cases,...

  20. Oregon Guidelines for Stormwater Management Plans for Removal...

    Open Energy Info (EERE)

    Oregon Guidelines for Stormwater Management Plans for RemovalFill Permit Applications Jump to: navigation, search OpenEI Reference LibraryAdd to library PermittingRegulatory...

  1. Development of a removable conformal coating through the synthetic...

    Office of Scientific and Technical Information (OSTI)

    Conference: Development of a removable conformal coating through the synthetic incorporation of Diels-Adler thermally reversible adducts into an epoxy resin. Citation Details...

  2. Removal of Animal Antibiotics for Potable Water Reclamation: A Review

    E-Print Network [OSTI]

    Chang, Rita

    2015-01-01

    Pharmaceuticals and personal care products in effluent matrices: A survey of transformation and removal during wastewater treatment and implications for wastewater management.

  3. Process to remove rare earth from IFR electrolyte

    DOE Patents [OSTI]

    Ackerman, John P. (Downers Grove, IL); Johnson, Terry R. (Wheaton, IL)

    1994-01-01

    The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner.

  4. Process to remove rare earth from IFR electrolyte

    DOE Patents [OSTI]

    Ackerman, J.P.; Johnson, T.R.

    1994-08-09

    The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner. 1 fig.

  5. Method of removing oxidized contaminants from water

    DOE Patents [OSTI]

    Amonette, J.E.; Fruchter, J.S.; Gorby, Y.A.; Cole, C.R.; Cantrell, K.J.; Kaplan, D.I.

    1998-07-21

    The present invention is a method for removing oxidized contaminant(s) from water. More specifically, the invention has the steps of contacting water containing the oxidized contaminant(s) with a layered aluminosilicate having Fe(II). The aluminosilicate may contain naturally occurring Fe(II), or the Fe(II) may be produced by reducing Fe(III) that is initially present. Reduction may be either by exposure to a chemical or biological reductant. Contacting the water containing oxidized contaminant(s) may be by (1) injection of Fe(II)-containing layered aluminosilicate, via a well, into a saturated zone where it is likely to intercept the contaminated water; (2) injection of contaminated water into a vessel containing the Fe(II)-bearing layered aluminosilicate; and (3) first reducing Fe(III) in the layered aluminosilicate to Fe(II) by injection of a biological or chemical reductant, into an aquifer or vessel having sufficient Fe(III)-bearing aluminosilicate to produce the necessary Fe(II). 8 figs.

  6. Method of removing oxidized contaminants from water

    DOE Patents [OSTI]

    Amonette, James E. (Richland, WA); Fruchter, Jonathan S. (Richland, WA); Gorby, Yuri A. (Richland, WA); Cole, Charles R. (West Richmond, WA); Cantrell, Kirk J. (West Richmond, WA); Kaplan, Daniel I. (Richland, WA)

    1998-01-01

    The present invention is a method for removing oxidized contaminant(s) from water. More specifically, the invention has the steps of contacting water containing the oxidized contaminant(s) with a layered aluminosilicate having Fe(II). The aluminosilicate may contain naturally occurring Fe(II), or the Fe(II) may be produced by reducing Fe(III) that is initially present. Reduction may be either by exposure to a chemical or biological reductant. Contacting the water containing oxidized contaminant(s) may be by (1) injection of Fe(II)-containing layered aluminosilicate, via a well, into a saturated zone where it is likely to intercept the contaminated water; (2) injection of contaminated water into a vessel containing the Fe(II)-bearing layered aluminosilicate; and (3) first reducing Fe(III) in the layered aluminosilicate to Fe(II) by injection of a biological or chemical reductant, into an aquifer or vessel having sufficient Fe(III)-bearing aluminosilicate to produce the necessary Fe(II).

  7. The washability of lignites for clay removal

    SciTech Connect (OSTI)

    Oteyaka, B.; Yamik, A.; Ucar, A.; Sahbaz, O.; Demir, U. [Dumlupinar University, Kutahya (Turkey). Dept. of Mining Engineering

    2008-07-01

    In the washability research of the Seyitomer Lignites (Kutahya-Turkey), with lower calorific value (1,863 kcal/kg) and high ash content (51.91%), by heavy medium separation, it was found out that middling clay in the coal had an effect to change the medium density. To prevent this problem, a trommel sieve with 18 and 5 mm aperture diameter was designed, and the clay in the coal was tried to be removed using it before the coal was released to heavy medium. Following that, the obtained coal in -100 + 18 mm and -18 + 5 mm fractions was subjected to sink and float test having 1.4 gcm{sup -3} and 1.7 gcm{sup -3} medium densities (-5 mm fraction will be evaluated in a separate work). Depending on the raw coal, with the floating of -100 + 18 mm and -18 + 5 mm size fraction in 1.4 gcm{sup -3} medium density, clean coal with 60.10% combustible matter recovery, 19.12% ash, and 3,150 kcal/kg was obtained. Also floating of the samples sinking in 1.4 gcm{sup -3} in the medium density (1.7 gcm{sup -3}), middling with 18.70% combustible matter recovery, 41.93% ash, 2,150 kcal/kg, and tailing having 78.31% ash were obtained.

  8. HIGH SO2 REMOVAL EFFICIENCY TESTING

    SciTech Connect (OSTI)

    Gary M. Blythe; James L. Phillips

    1997-10-15

    This final report describes the results of performance tests at six full-scale wet lime- and limestone-reagent flue gas desulfurization (FGD) systems. The objective of these tests was to evaluate the effectiveness of low capital cost sulfur dioxide (SO{sub 2}) removal upgrades for existing FGD systems as an option for complying with the provisions of the Clean Air Act Amendments of 1990. The upgrade options tested at the limestone-reagent systems included the use of organic acid additives (dibasic acid (DBA) and/or sodium formate) as well as increased reagent ratio (higher excess limestone levels in the recirculating slurry solids) and absorber liquid-to-gas ratio. One system also tested operating at higher flue gas velocities to allow the existing FGD system to treat flue gas from an adjacent, unscrubbed unit. Upgrade options for the one lime-based system tested included increased absorber venturi pressure drop and increased sulfite concentration in the recirculating slurry liquor.

  9. Improved Processes to Remove Naphthenic Acids

    SciTech Connect (OSTI)

    Aihua Zhang; Qisheng Ma; Kangshi Wang; Yongchun Tang; William A. Goddard

    2005-12-09

    In the past three years, we followed the work plan as we suggested in the proposal and made every efforts to fulfill the project objectives. Based on our large amount of creative and productive work, including both of experimental and theoretic aspects, we received important technical breakthrough on naphthenic acid removal process and obtained deep insight on catalytic decarboxylation chemistry. In detail, we established an integrated methodology to serve for all of the experimental and theoretical work. Our experimental investigation results in discovery of four type effective catalysts to the reaction of decarboxylation of model carboxylic acid compounds. The adsorption experiment revealed the effectiveness of several solid materials to naphthenic acid adsorption and acidity reduction of crude oil, which can be either natural minerals or synthesized materials. The test with crude oil also received promising results, which can be potentially developed into a practical process for oil industry. The theoretical work predicted several possible catalytic decarboxylation mechanisms that would govern the decarboxylation pathways depending on the type of catalysts being used. The calculation for reaction activation energy was in good agreement with our experimental measurements.

  10. Passive shut-down heat removal system

    DOE Patents [OSTI]

    Hundal, Rolv (Greensburg, PA); Sharbaugh, John E. (Bullskin Township, Fayette County, PA)

    1988-01-01

    An improved shut-down heat removal system for a liquid metal nuclear reactor of the type having a vessel for holding hot and cold pools of liquid sodium is disclosed herein. Generally, the improved system comprises a redan or barrier within the reactor vessel which allows an auxiliary heat exchanger to become immersed in liquid sodium from the hot pool whenever the reactor pump fails to generate a metal-circulating pressure differential between the hot and cold pools of sodium. This redan also defines an alternative circulation path between the hot and cold pools of sodium in order to equilibrate the distribution of the decay heat from the reactor core. The invention may take the form of a redan or barrier that circumscribes the inner wall of the reactor vessel, thereby defining an annular space therebetween. In this embodiment, the bottom of the annular space communicates with the cold pool of sodium, and the auxiliary heat exchanger is placed in this annular space just above the drawn-down level that the liquid sodium assumes during normal operating conditions. Alternatively, the redan of the invention may include a pair of vertically oriented, concentrically disposed standpipes having a piston member disposed between them that operates somewhat like a pressure-sensitive valve. In both embodiments, the cessation of the pressure differential that is normally created by the reactor pump causes the auxiliary heat exchanger to be immersed in liquid sodium from the hot pool. Additionally, the redan in both embodiments forms a circulation flow path between the hot and cold pools so that the decay heat from the nuclear core is uniformly distributed within the vessel.

  11. Process for removing metal carbonyls from gaseous streams

    SciTech Connect (OSTI)

    Heyd, R.L.; Pignet, T.P.

    1988-04-26

    A process for removing metal carbonyl contaminates from a gaseous stream is described containing such contaminates and which is free from sulfur contaminates, which process comprises contacting the gaseous stream with a zinc sulfide absorbent to thereby remove metal carbonyl contaminates from the gaseous stream, and separating the gaseous stream from the zinc sulfide absorbent.

  12. EBeam Irradiation for Water Reuse: Removal of Bromate 

    E-Print Network [OSTI]

    Wang, Li

    2015-07-28

    Beam) irradiation has been investigated in areas including both bacterial/viral disinfection and chemical contaminant removal. However, eBeam research on BrO3- removal is limited. Particularly, the application of eBeam to water reuse has not been investigated...

  13. Continuous cryopump with a method for removal of solidified gases

    DOE Patents [OSTI]

    Carlson, L.W.; Herman, H.

    1988-05-05

    An improved cryopump for the removal of gases from a high vacuum, comprising a cryopanel incorporating honeycomb structure, refrigerant means thermally connected to the cryopanel, and a rotatable channel moving azimuthally around an axis located near the center of the cryopanel, removing gases adsorbed within the honeycomb structure by subliming them and conducting them outside the vacuum vessel. 4 figs.

  14. Removal of Estrogenic Pollutants from Contaminated Water Using

    E-Print Network [OSTI]

    Chen, Wilfred

    Removal of Estrogenic Pollutants from Contaminated Water Using Molecularly Imprinted Polymers Z I H that this material may be appropriate for treating a complex mixture of estrogenic pollutants. The feasibility of removing estrogenic compounds from environmental water by the MIP was demonstrated using lake water spiked

  15. Method for removing chlorine compounds from hydrocarbon mixtures

    DOE Patents [OSTI]

    Janoski, E.J.; Hollstein, E.J.

    1984-09-29

    A process for removing halide ions from a hydrocarbon feedstream containing halogenated hydrocarbons wherein the contaminated feedstock is contacted with a solution of a suitable oxidizing acid containing a lanthanide oxide, the acid being present in a concentration of at least about 50 weight percent for a time sufficient to remove substantially all of the halide ion from the hydrocarbon feedstock.

  16. Process for removing pyritic sulfur from bituminous coals

    DOE Patents [OSTI]

    Pawlak, Wanda (Edmonton, CA); Janiak, Jerzy S. (Edmonton, CA); Turak, Ali A. (Edmonton, CA); Ignasiak, Boleslaw L. (Edmonton, CA)

    1990-01-01

    A process is provided for removing pyritic sulfur and lowering ash content of bituminous coals by grinding the feed coal, subjecting it to micro-agglomeration with a bridging liquid containing heavy oil, separating the microagglomerates and separating them to a water wash to remove suspended pyritic sulfur. In one embodiment the coal is subjected to a second micro-agglomeration step.

  17. Process for selected gas oxide removal by radiofrequency catalysts

    DOE Patents [OSTI]

    Cha, C.Y.

    1993-09-21

    This process to remove gas oxides from flue gas utilizes adsorption on a char bed subsequently followed by radiofrequency catalysis enhancing such removal through selected reactions. Common gas oxides include SO[sub 2] and NO[sub x]. 1 figure.

  18. Water supplier copes with lead paint removal regs

    SciTech Connect (OSTI)

    Becker, C.E. ); Lovejoy, D.R.; Bryck, J.L.; Rockensies, W.H.

    1993-12-01

    This article examines new paint removal methods that minimize releasing of paints containing lead to the environment and lead free coating systems for tank corrosion protection used in the Village of Freeport in Long Island, New York. The topics of the article include coating failures, removal tools and methods, paint and application methods.

  19. Removal of residual particulate matter from filter media

    DOE Patents [OSTI]

    Almlie, Jay C; Miller, Stanley J

    2014-11-11

    A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

  20. UNL/OSU Researchers Try Promising Technique to Remove Groundwater

    E-Print Network [OSTI]

    Nebraska-Lincoln, University of

    UNL/OSU Researchers Try Promising Technique to Remove Groundwater Contamination Under Former Oklahoma State University have joined to test promising new methods of removing longstanding groundwater into specially drilled injection wells, where it mixes with contaminants in the groundwater under the former

  1. ITER HEAT REMOVAL SYSTEM SYSTEM & PROCESS CONTROL DESIGN

    E-Print Network [OSTI]

    Raffray, A. René

    in-vessel component cooling systems malfunction. Therefore, special design criteria are requestedITER HEAT REMOVAL SYSTEM SYSTEM & PROCESS CONTROL DESIGN Y. Hoshi 1 , Y. Kataoka 2 , V. Tanchuk 1 the vacuum vessel cooling system has a safety role of providing the ultimate decay heat removal system ,when

  2. Regenerable hydrogen chloride removal sorbent and regenerable multi-functional hydrogen sulfide and hydrogen chloride removal sorbent for high temperature gas streams

    DOE Patents [OSTI]

    Siriwardane, Ranjani (Morgantown, WV)

    2010-08-03

    Regenerable hydrogen chloride removal sorbent and regenerable multi-functional hydrogen sulfide and hydrogen chloride removal sorbent for high temperature gas streams

  3. Enhanced Organic Precursor Removals Using "Aged" Filter Media Page 1 Enhanced Organic Precursor Removals Using "Aged" Filter Media

    E-Print Network [OSTI]

    OH. Fresh buffered water and influent solution were prepared prior to each filter challenge. C. CoagulatedEnhanced Organic Precursor Removals Using "Aged" Filter Media Page 1 Enhanced Organic Precursor Removals Using "Aged" Filter Media O b j e c t i v e s The main goals of this project was to evaluate

  4. Arsenic Removal Using AgedArsenic Removal Using Aged Rapid Sand Filter MediaRapid Sand Filter Media

    E-Print Network [OSTI]

    Arsenic Removal Using AgedArsenic Removal Using Aged Rapid Sand Filter MediaRapid Sand Filter Media byby C. Menard, D. Burt, M.R. CollinsC. Menard, D. Burt, M.R. Collins Water Treatment Technology Assistance CenterWater Treatment Technology Assistance Center Department of Civil Engineering

  5. Productive Energy of Some Feeds and Foods as Measured by Gains of Energy by Growing Chickens. 

    E-Print Network [OSTI]

    Fraps, G. S. (George Stronach); Carlyle, E. C. (Elmer Cardinal)

    1942-01-01

    STATION A B. CONNER, DIRECTOR, College Station, Texas BULLETIN NO. 625 DECEMBER 1942 PRODUCTIVE ENERGY OF SOME FEEDS AND FOODS AS MEASURED BY GAINS OF ENERGY BY GROWING CHICKENS G. S. FRAPS AND E. C. CARLYLE Division of Chemistry -* LIBRA RY... Aflculfural&~eetv~! ~~i\\~~~~~~~ - 601i~p7 ~faf>~ T kJ;:~: AGRICULTURAL AND MECHANICAL COLLEGE OF' TEXAS T. 0. WALTON, President B-28-1242-6M-L180 - IC- - [Blank Page in Original Bulletin] The value of 62 feeds and foods for furnishing energy for growing...

  6. Passive removal of manganese from acid mine drainage

    SciTech Connect (OSTI)

    Brant, D.L.; Ziemkiewicz, P.F. [West Virginia Univ., Morgantown, WV (United States)

    1997-12-31

    Removal of manganese (Mn) from mine drainage is difficult due to the abnormal chemistry of the element. The removal requires the oxidation of Mn(II) (the form found in mine drainage) to the more oxidized forms (Mn(III) or Mn(IV)). The more oxidized forms exist only as solids and will not return to Mn(II) spontaneously. Chemical treatment of Mn often requires a pH near 10 to initiate the oxidation quickly. A stabilized pH of 10 normally causes more harm to aquatic organisms than the Mn and is not desirable, making additional steps in the treatment necessary. Biological removal of Mn can be achieved at near neutral pH levels. The Shade Mining site in Somerset County, PA has been treating Mn to discharge limits since the early 1990`s (reducing Mn concentrations from 12 - 25 mg/L in the influent to <2 mg/L in the effluent). The treatment system consists of an anoxic limestone drain discharging into a wetland to remove iron, aluminum, and acidity, while increasing pH and alkalinity. The wetland effluent flows into two limestone beds (Mn removal). The limestone beds developed a black slime coating as the Mn removal increased. This system continues to remove Mn in all weather conditions and has not required chemical treatment since the black coating appeared on the limestone. A laboratory study was conducted using limestone collected from the Shade site to use the same naturally occurring Mn oxidizing microbes. The lab study compared W removal rates of microbial oxidation, MnO{sub 2} catalyzed limestone, and fresh uncoated limestone. The microbial removal performed the best (25 mg/L Mn reduced to <2 mg/L in 72 hours).

  7. Tank 241-CX-70 waste removal and packaging

    SciTech Connect (OSTI)

    DuVon, D.K.

    1993-06-01

    Tank 241-CX-70, located on the Hanford Site in Washington State, is a 30,000 gal single-shell storage tank built in 1952 to hold high-level process waste from pilot tests of the reduction-oxidation process. In 1979 decommissioning operations were begun by pumping liquid waste from the tank to the double-shell tank (DST) 101-AY. Not all the waste was removed at that time. Approximately 10,300 gal of sludge remained. On September 25, 1987, operations were resumed to remove the remaining waste using a sluicing and pumping method. This report documents the final removal of waste from Tank 241-CX-70.

  8. Tank 241-CX-70 waste removal and packaging

    SciTech Connect (OSTI)

    DuVon, D.K.

    1993-01-01

    Tank 241-CX-70, located on the Hanford Site in Washington State, is a 30,000 gal single-shell storage tank built in 1952 to hold high-level process waste from pilot tests of the reduction-oxidation process. In 1979 decommissioning operations were begun by pumping liquid waste from the tank to the double-shell tank (DST) 101-AY. Not all the waste was removed at that time. Approximately 10,300 gal of sludge remained. On September 25, 1987, operations were resumed to remove the remaining waste using a sluicing and pumping method. This report documents the final removal of waste from Tank 241-CX-70.

  9. Duct Remediation Program: Material characterization and removal/handling

    SciTech Connect (OSTI)

    Beckman, T.d.; Davis, M.M.; Karas, T.M.

    1992-11-01

    Remediation efforts were successfully performed at Rocky Flats to locate, characterize, and remove plutonium holdup from process exhaust ducts. Non-Destructive Assay (NDA) techniques were used to determine holdup locations and quantities. Visual characterization using video probes helped determine the physical properties of the material, which were used for remediation planning. Assorted equipment types, such as vacuum systems, scoops, brushes, and a rotating removal system, were developed to remove specific material types. Personnel safety and material handling requirements were addressed throughout the project.

  10. Technology Assistance Program Growing technology-based business with free service

    E-Print Network [OSTI]

    Technology Assistance Program Growing technology-based business with free service Economic Development Is your small, technology-based business faced with a specific challenge, but lacking scientist or engineer help your company? If the answer is yes, the Technology Assistance Program (TAP

  11. INTRODUCTION There is growing recognition that responses to global warming will

    E-Print Network [OSTI]

    Neff, Bryan D.

    3436 INTRODUCTION There is growing recognition that responses to global warming will vary among increase with temperature (Gillooly et al., 2001; Sogard and Spencer, 2004). SUMMARY Global warming poses species (Pörtner et al., 2008; Eliason et al., 2011). With the average global air temperature projected

  12. Wind power is a rapidly growing con-tributor to worldwide energy supplies and

    E-Print Network [OSTI]

    Doty, Sharon Lafferty

    Wind power is a rapidly growing con- tributor to worldwide energy supplies and UW Atmospheric the weather for the Bonneville Power Admin- istration, he moved to PPM Energy, a lead- ing wind energy rapidly moved into the new field of wind energy prediction, using a sophisticated suite of numerical

  13. Wind power is a rapidly growing and evolving field that crosses traditional academic disciplines and increasingly

    E-Print Network [OSTI]

    Firestone, Jeremy

    Wind power is a rapidly growing and evolving field that crosses traditional academic disciplines to locate wind power projects, the economics and regulatory policies governing wind power and the complex wind projects. Interdisciplinary Research and Education The Wind Power Science, Engineering and Policy

  14. Abstract--The growing popularity and success of fuel cells in aerospace, stationary power, and transportation

    E-Print Network [OSTI]

    Rincon-Mora, Gabriel A.

    1 Abstract-- The growing popularity and success of fuel cells in aerospace, stationary power runtime, and decreasing size. Di- rect-methanol fuel cell batteries have now been built and conformed to low cost technologies and chip-scale dimen- sions. Conventional fuel cell models, however, fail

  15. The Wulff Shape as the Asymptotic Limit of a Growing Crystalline Interface*

    E-Print Network [OSTI]

    Ferguson, Thomas S.

    The Wulff Shape as the Asymptotic Limit of a Growing Crystalline Interface* by Stanley Osher of crystalline materials in the plane, and the propagation of shock waves. They show that there is a precise sense in which any two dimensional crystalline form can be described in terms of rarefaction waves

  16. Detection of Oil Spills in SAR Images Using Wavelets and Region Growing

    E-Print Network [OSTI]

    de Figueiredo, Luiz Henrique

    Detection of Oil Spills in SAR Images Using Wavelets and Region Growing RÉGIA T. S. ARAÚJO, FÁTIMA an algorithm to detect oil spills in Synthetic Aperture Radar (SAR) images that can be used to support sensing of environmental disasters. Spillage of oil in coastal waters can be a catastrophic event

  17. NRRI NowWinter 2009 GrowingStrongIndustries~DevelopingNewIdeas~NurturingNaturalResources

    E-Print Network [OSTI]

    Netoff, Theoden

    of India and China are expected to push demand even further. By 2030, worldwide consumption of oilNRRI NowWinter 2009 GrowingStrongIndustries~DevelopingNewIdeas~NurturingNaturalResources 2 Energy. There is enough oil to meet the expected demand for the next 40 years, according to analyses of oil and natural

  18. Art and Science for Life: Designing and Growing Virtual Plants with L-systems

    E-Print Network [OSTI]

    Prusinkiewicz, Przemyslaw

    Art and Science for Life: Designing and Growing Virtual Plants with L-systems Przemyslaw@cpsc.ucalgary.ca Abstract Virtual plants are computer models that recreate the structure and simulate the development of plants. Virtual plant modeling is an interdisciplinary area combining mathematical formalisms, biological

  19. Growing Green As part of its strategic plan to foster growth and development in key

    E-Print Network [OSTI]

    Lennard, William N.

    -of-the-art, environmentally friendly and energy-efficient building that houses advanced environmental engineering and greenGrowing Green As part of its strategic plan to foster growth and development in key areas related to energy and the environment, Western University has created the Centre for Environmental Sustainability

  20. Evaluation of Two Methods to Prevent Bovine Respiratory Disease in Growing Cattle 

    E-Print Network [OSTI]

    Word, Alyssa Brook

    2014-07-09

    performance outcomes were not different, animal health was improved with metaphylaxis. A second trial was conducted to determine the effects of limit-feeding growing steers on immune function. Thirty-two steers were fed the same ration at one of three intake...

  1. Abstract--Despite growing interest in the behavior of electromyographic signals during muscle fatigue, few studies

    E-Print Network [OSTI]

    Carvalho, João Luiz

    Abstract--Despite growing interest in the behavior of electromyographic signals during muscle fatigue, few studies investigate fatigue recovery. In this work, we use surface electromyographic signals for each experimental group: 1, 2, 4, 8, 24 and 48 hours. Surface electromyographic signals were acquired

  2. Journal of Biomechanics 40 (2007) 412426 Haemodynamics and wall remodelling of a growing cerebral

    E-Print Network [OSTI]

    Daraio, Chiara

    2007-01-01

    Journal of Biomechanics 40 (2007) 412­426 Haemodynamics and wall remodelling of a growing cerebral wall under constant tension is a biomechanical process of rupture, degradation and reconstruction biomechanical mechanisms cannot be found in the literature. The aim of this study is to investigate

  3. Food-stamp use triples as local despair grows By ANA M. VALDES AND ADAM PLAYFORD

    E-Print Network [OSTI]

    Fernandez, Eduardo

    Food-stamp use triples as local despair grows By ANA M. VALDES AND ADAM PLAYFORD Palm Beach Post increases every year in the number of individuals using food stamps to feed their families. In Palm Beach County, 161,250 of the county's 1.3 million residents - 12.4 percent - received food stamps in August

  4. improving energy efficiency in the built environment is now seen as a growing

    E-Print Network [OSTI]

    Kotchen, Matthew J.

    improving energy efficiency in the built environment is now seen as a growing policy priority the 1973 oil embargo. Codes by state but they generally establish a minimum energy efficiency stan- dard.S. Department of Energy to establish building code energy efficiency targets by January 1, 2014. it also

  5. plagioclase phenocrysts form in a magma reservoir but then grow considerably during

    E-Print Network [OSTI]

    Paulsson, Johan

    plagioclase phenocrysts form in a magma reservoir but then grow considerably during an eruption range in observed H2O contents (0.3­6.4 wt%) as representing saturation at pressures ranging from those at reservoir level all the way up to those near the surface. They also recognize a consistent rela- tionship

  6. Carbon limitation of soil respiration under winter snowpacks: potential feedbacks between growing season

    E-Print Network [OSTI]

    Carbon limitation of soil respiration under winter snowpacks: potential feedbacks between growing season and winter carbon fluxes PA U L D . B R O O K S *, D I A N E M C K N I G H T w and K E L LY E L D- latitude and high-elevation ecosystems may increase soil carbon availability both through increased litter

  7. Growing season methyl bromide and methyl chloride fluxes at a sub-arctic wetland in Sweden 

    E-Print Network [OSTI]

    Hardacre, Catherine J.; Blei, Emanuel; Heal, Mathew R

    2009-01-01

    Methyl bromide and methyl chloride fluxes were measured at several sites in a sub-arctic wetland near Abisko, Sweden (68°28?N 18°49?E) throughout the 2008 growing season. Averaged over 92 flux measurements the sub-arctic ...

  8. Carbon sequestration and biodiversity of re-growing miombo woodlands in Mozambique

    E-Print Network [OSTI]

    Carbon sequestration and biodiversity of re-growing miombo woodlands in Mozambique M. Williams a in tropical woodlands is being used to sequester carbon (C), alleviate poverty and protect biodiversity, among there is a potential for C sequestration in soils on abandoned farmland. Management should focus on identifying C

  9. Elastic Instability in Growing Yeast Colonies Baochi Nguyen,* Arpita Upadhyaya,y

    E-Print Network [OSTI]

    van Oudenaarden, Alexander

    the overall adhesive energy between cell surfaces. We demonstrate in a model experimental system that there exist conditions where a slowly growing tissue does not minimize this adhesive energy. A mathematical elastic and surface energies. INTRODUCTION The differential adhesion hypothesis states that cells

  10. Removal of carbonyl sulfide from liquid hydrocarbon streams

    SciTech Connect (OSTI)

    Damron, E.; Mick, M.B.; Woodall, R.M.

    1981-09-22

    Carbonyl sulfide is removed from propane and other similar liquefied petroleum gas products by mixing liquid methanol with the untreated liquefied gas and then contacting the liquid mixture with solid potassium hydroxide.

  11. Method to remove uranium/vanadium contamination from groundwater

    DOE Patents [OSTI]

    Metzler, Donald R. (DeBeque, CO); Morrison, Stanley (Grand Junction, CO)

    2004-07-27

    A process for removing uranium/vanadium-based contaminants from groundwater using a primary in-ground treatment media and a pretreatment media that chemically adjusts the groundwater contaminant to provide for optimum treatment by the primary treatment media.

  12. Removal Rate Model for Magnetorheological Finishing of Glass

    SciTech Connect (OSTI)

    DeGroote, J.E.; Marino, A.E.; WIlson, J.P.; Bishop, A.L.; Lambropoulos, J.C.; Jacobs, S.D.

    2007-11-14

    Magnetorheological finishing (MRF) is a deterministic subaperture polishing process. The process uses a magntorheological (MR) fluid that consists of micrometer-sized, spherical, magnetic carbonyl iron (CI) particles, nonmagnetic polishing abrasives, water, and stabilizers. Material removal occurs when the CI and nonmagnetic polishing abrasives shear material off the surface being polished. We introduce a new MRF material removal rate model for glass. This model contains terms for the near surface mechanical properties of glass, drag force, polishing abrasive size and concentration, chemical durability of the glass, MR fluid pH, and the glass composition. We introduce quantitative chemical predictors for the first time, to the best of our knowledge, into an MRF removal rate model. We validate individual terms in our model separately and then combine all of the terms to show the whole MRF material removal model compared with experimental data. All of our experimental data were obtained using nanodiamond MR fluids and a set of six optical glasses.

  13. Massive Hanford Test Reactor Removed - Plutonium Recycle Test...

    Energy Savers [EERE]

    challenge on the U.S. Department of Energy's (DOE) Hanford Site by removing a 1,082-ton nuclear test reactor from the 300 Area. The River Corridor is a 220-square-mile section of...

  14. Lab sets new record for waste volume removed

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of the waste were removed, and 220 shipments were sent to WIPP. The data represents the fourth year in a row that the Lab has set new LANL records for TRU waste shipments. Next...

  15. BOD5 removal in subsurface flow constructed wetlands 

    E-Print Network [OSTI]

    Melton, Rebecca Hobbs

    2005-08-29

    advanced or secondary treatment of domestic wastewater. The pollutant removal efficiency in SFCW depends on design parameters. Many of these factors have been investigated while others such as aspect ratio, design of water inlet structure and method...

  16. Ozone Removal by Filters Containing Activated Carbon: A Pilot Study

    E-Print Network [OSTI]

    Fisk, William

    2012-01-01

    removing particulate matter. ANSI/ASHRAE standard 52.1-1992efficiency by particle size. ANSI/ASHRAE Standard 52.2-1999.GA, ASHRAE. ASHRAE (2007). ANSI/ASHRAE Standard 62.1.

  17. Method to Remove Uranium/Vanadium Contamination from Groundwater

    DOE Patents [OSTI]

    Metzler, Donald R.; Morrison Stanley

    2004-07-27

    A process for removing uranium/vanadium-based contaminants from groundwater using a primary in-ground treatment media and a pretreatment media that chemically adjusts the groundwater contaminant to provide for optimum treatment by the primary treatment media.

  18. Process for the removal of acid gases from gaseous streams

    SciTech Connect (OSTI)

    Blytas, G.C.; Diaz, Z.

    1982-11-16

    Hydrogen sulfide, carbon dioxide, and carbonyl sulfide are removed from a gas stream in a staged procedure by: absorption of the CO/sub 2/ and COS; conversion of the hydrogen sulfide to produce sulfur in an absorbent mixture; hydrolysis of the carbonyl sulfide to produce a gas stream of hydrogen sulfide and carbon dioxide; and removal of the hydrogen sulfide from the gas stream.

  19. Radiator debris removing apparatus and work machine using same

    DOE Patents [OSTI]

    Martin, Kevin L. (Washburn, IL); Elliott, Dwight E. (Chillicothe, IL)

    2008-09-02

    A radiator assembly includes a finned radiator core and a debris removing apparatus having a compressed air inlet and at least one compressed air outlet configured to direct compressed air through the radiator core. A work machine such as a wheel loader includes a radiator and a debris removing apparatus coupled with on-board compressed air and having at least one pressurized gas outlet configured to direct a gas toward the face of the radiator.

  20. Process for removing heavy metal compounds from heavy crude oil

    DOE Patents [OSTI]

    Cha, Chang Y. (Golden, CO); Boysen, John E. (Laramie, WY); Branthaver, Jan F. (Laramie, WY)

    1991-01-01

    A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

  1. Method for removing oxide contamination from titanium diboride powder

    DOE Patents [OSTI]

    Brynestad, Jorulf (Oak Ridge, TN); Bamberger, Carlos E. (Oak Ridge, TN)

    1984-01-01

    A method for removing oxide contamination from titanium diboride powder involves the direct chemical treatment of TiB.sub.2 powders with a gaseous boron halide, such as BCl.sub.3, at temperatures in the range of 500.degree.-800.degree. C. The BCl.sub.3 reacts with the oxides to form volatile species which are removed by the BCl.sub.3 exit stream.

  2. Fluidized bed gasification ash reduction and removal system

    DOE Patents [OSTI]

    Schenone, Carl E. (Madison, PA); Rosinski, Joseph (Vanderbilt, PA)

    1984-02-28

    In a fluidized bed gasification system an ash removal system to reduce the particulate ash to a maximum size or smaller, allow the ash to cool to a temperature lower than the gasifier and remove the ash from the gasifier system. The system consists of a crusher, a container containing level probes and a means for controlling the rotational speed of the crusher based on the level of ash within the container.

  3. Fluidized bed gasification ash reduction and removal process

    DOE Patents [OSTI]

    Schenone, Carl E. (Madison, PA); Rosinski, Joseph (Vanderbilt, PA)

    1984-12-04

    In a fluidized bed gasification system an ash removal system to reduce the particulate ash to a maximum size or smaller, allow the ash to cool to a temperature lower than the gasifier and remove the ash from the gasifier system. The system consists of a crusher, a container containing level probes and a means for controlling the rotational speed of the crusher based on the level of ash within the container.

  4. Solid materials for removing arsenic and method thereof

    SciTech Connect (OSTI)

    Coronado, Paul R. (Livermore, CA); Coleman, Sabre J. (Oakland, CA); Sanner, Robert D. (Livermore, CA); Dias, Victoria L. (Livermore, CA); Reynolds, John G. (San Ramon, CA)

    2008-07-01

    Solid materials have been developed to remove arsenic compounds from aqueous media. The arsenic is removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the arsenic leaving a purified aqueous stream. The materials are aerogels or xerogels and aerogels or xerogels and solid support structure, e.g., granulated activated carbon (GAC), mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards arsenic.

  5. Solid materials for removing arsenic and method thereof

    DOE Patents [OSTI]

    Coronado, Paul R. (Livermore, CA); Coleman, Sabre J. (Oakland, CA); Sanner, Robert D. (Livermore, CA); Dias, Victoria L. (Livermore, CA); Reynolds, John G. (San Ramon, CA)

    2010-09-28

    Solid materials have been developed to remove arsenic compounds from aqueous media. The arsenic is removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the arsenic leaving a purified aqueous stream. The materials are aerogels or xerogels and aerogels or xerogels and solid support structure, e.g., granulated activated carbon (GAC), mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards arsenic.

  6. Video requirements plan for the HMT equipment removal system

    SciTech Connect (OSTI)

    Vargo, G.F. Jr.

    1995-02-01

    This document is the plan defining the video coverage requirements for the equipment removal event of the Hydrogen Mitigation Test (HMT) mixer pump currently installed in high level nuclear waste storage Tank 241-SY-101. When the mixer pump fails the removal and installation of a spare pump will be a time critical event. Since the success of the HMT mixer pump has resolved the DOE safety issue it is absolutely essential that mixing be restored to the tank in a short as time possible. Therefore, the removal of the failed pump and the installation of the spare pump must be anticipated and planned well in advance. The removal, containment, transporting, and storage of the failed pump is a very complex and hazardous task. The successful completion of this task will require careful planning and monitoring. Certain events, during the removal and subsequent installation of the new pump, will require video observation and storage for safety, documenting, training, and promotional use. Furthermore, certain events will require close monitoring and observation by the event directors and key supervisory personnel for the execution of specific tasks during the equipment removal event.

  7. Growing consumption of petroleum products worldwide has resulted in the proliferation of vessels carrying oil, chemicals, and gases

    E-Print Network [OSTI]

    Neimark, Alexander V.

    Growing consumption of petroleum products worldwide has resulted in the proliferation of vessels carrying oil, chemicals, and gases into our harbors. Meeting our society's surging demand for commodities

  8. Contoured inner after-heater shield for reducing stress in growing crystalline bodies

    DOE Patents [OSTI]

    Kalejs, Juris P. (Wellesley, MA)

    1996-09-24

    An apparatus for growing hollow crystalline bodies by the EFG process, comprising an EFG die having a top surface shaped for growing a hollow crystalline body having a cross-sectional configuration in the shape of a polygon having n faces, and a radiation shield adjacent to and surrounded by the top end surface of the die, characterized in that the shield has an inner edge defining a similar polygon with n sides, and the inner edge of the shield is notched so that the spacing between the n faces and the n sides is greatest between the central portions of the n faces and the n sides, whereby the greater spacing at the central portions helps to reduce lateral temperature gradients in the crystalline body that is grown by use of the die.

  9. Synechococcus elongatus UTEX 2973, a fast growing cyanobacterial chassis for biosynthesis using light and CO2

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Yu, Jingjie; Liberton, Michelle; Cliften, Paul F.; Head, Richard D.; Jacobs, Jon M.; Smith, Richard D.; Koppenaal, David W.; Brand, Jerry J.; Pakrasi, Himadri B.

    2015-01-30

    Photosynthetic microbes are of emerging interest as production organisms in biotechnology because they can grow autotrophically using sunlight, an abundant energy source, and CO2, a greenhouse gas. Important traits for such microbes are fast growth and amenability to genetic manipulation. Here we describe Synechococcus elongatus UTEX 2973, a unicellular cyanobacterium capable of rapid autotrophic growth, comparable to heterotrophic industrial hosts such as yeast. Synechococcus 2973 can be readily transformed for facile generation of desired knockout and knock-in mutations. Genome sequencing coupled with global proteomics studies revealed that Synechococcus 2973 is a close relative of the widely studied cyanobacterium Synechococcus elongatusmore »PCC 7942, an organism that grows more than two times slower. A small number of nucleotide changes are the only significant differences between the genomes of these two cyanobacterial strains. Thus, our study has unraveled genetic determinants necessary for rapid growth of cyanobacterial strains of significant industrial potential.« less

  10. Productive Energy of Certain Feeds as Measured by Production of Fat and Flesh by Growing Rats. 

    E-Print Network [OSTI]

    Fraps, G. S. (George Stronach)

    1943-01-01

    STATION A B. CONNER, DIRECTOR, College Station, Texas BUIJTJETIN NO. ($32 OCTOBER 1943 PRODUCTIVE ENERGY OF CERTAIN FEEDS AS MEASURED BY PRODUCTION OF FAT AND FLESH BY GROWING RATS G. S. FRAPS Division of Chemistry AGRICULTZTRAL AND MECHANICAL... COLLEGE OF TEXAS T. 0. WALTON, President [Blank Page in Original Bulletin] 'revious work with chickens shoxved that the energy values of feeds re very nearly in proportion to the digestible nutrients. Experiments *e made with a different kind...

  11. Mesoscopic model for filament orientation in growing actin networks: the role of obstacle geometry

    E-Print Network [OSTI]

    Julian Weichsel; Ulrich S. Schwarz

    2013-04-13

    Propulsion by growing actin networks is a universal mechanism used in many different biological systems. Although the core molecular machinery for actin network growth is well preserved in most cases, the geometry of the propelled obstacle can vary considerably. In recent years, filament orientation distribution has emerged as an important observable characterizing the structure and dynamical state of the growing network. Here we derive several continuum equations for the orientation distribution of filaments growing behind stiff obstacles of various shapes and validate the predicted steady state orientation patterns by stochastic computer simulations based on discrete filaments. We use an ordinary differential equation approach to demonstrate that for flat obstacles of finite size, two fundamentally different orientation patterns peaked at either +35/-35 or +70/0/-70 degrees exhibit mutually exclusive stability, in agreement with earlier results for flat obstacles of very large lateral extension. We calculate and validate phase diagrams as a function of model parameters and show how this approach can be extended to obstacles with piecewise straight contours. For curved obstacles, we arrive at a partial differential equation in the continuum limit, which again is in good agreement with the computer simulations. In all cases, we can identify the same two fundamentally different orientation patterns, but only within an appropriate reference frame, which is adjusted to the local orientation of the obstacle contour. Our results suggest that two fundamentally different network architectures compete with each other in growing actin networks, irrespective of obstacle geometry, and clarify how simulated and electron tomography data have to be analyzed for non-flat obstacle geometries.

  12. Modeling water uptake by a root system growing in a fixed soil volume

    E-Print Network [OSTI]

    Albrieu, J L Blengino; Tarzia, D A

    2015-01-01

    The water uptake by roots of plants is examined for an ideal situation, with an approximation that resembles plants growing in pots, meaning that the total soil volume is fixed. We propose a coupled water uptake-root growth model. A one-dimensional model for water flux and water uptake by a root system growing uniformly distributed in the soil is presented, and the Van Genuchten model for the transport of water in soil is used. The governing equations are represented by a moving boundary model for which the root length, as a function of time, is prescribed. The solution of the model is obtained by front-fixing and finite element methods. Model predictions for water uptake by a same plant growing in loam, silt and clay soils are obtained and compared. A sensitivity analysis to determine relative effects on water uptake when system parameters are changed is also presented and shows that the model and numerical method proposed are more sensitive to the root growth rate than to the rest of the parameters. This se...

  13. A method for removing arm backscatter from EPID images

    SciTech Connect (OSTI)

    King, Brian W. [School of Mathematical and Physics Sciences, University of Newcastle, Newcastle, New South Wales 2308 (Australia); Greer, Peter B. [Department of Radiation Oncology, Calvary Mater Newcastle Hospital, Newcastle, New South Wales 2310 (Australia); School of Mathematical and Physical Sciences, University of Newcastle, Newcastle, New South Wales 2308 (Australia)

    2013-07-15

    Purpose: To develop a method for removing the support arm backscatter from images acquired using current Varian electronic portal imaging devices (EPIDs).Methods: The effect of arm backscatter on EPID images was modeled using a kernel convolution method. The parameters of the model were optimized by comparing on-arm images to off-arm images. The model was used to develop a method to remove the effect of backscatter from measured EPID images. The performance of the backscatter removal method was tested by comparing backscatter corrected on-arm images to measured off-arm images for 17 rectangular fields of different sizes and locations on the imager. The method was also tested using on- and off-arm images from 42 intensity modulated radiotherapy (IMRT) fields.Results: Images generated by the backscatter removal method gave consistently better agreement with off-arm images than images without backscatter correction. For the 17 rectangular fields studied, the root mean square difference of in-plane profiles compared to off-arm profiles was reduced from 1.19% (standard deviation 0.59%) on average without backscatter removal to 0.38% (standard deviation 0.18%) when using the backscatter removal method. When comparing to the off-arm images from the 42 IMRT fields, the mean {gamma} and percentage of pixels with {gamma} < 1 were improved by the backscatter removal method in all but one of the images studied. The mean {gamma} value (1%, 1 mm) for the IMRT fields studied was reduced from 0.80 to 0.57 by using the backscatter removal method, while the mean {gamma} pass rate was increased from 72.2% to 84.6%.Conclusions: A backscatter removal method has been developed to estimate the image acquired by the EPID without any arm backscatter from an image acquired in the presence of arm backscatter. The method has been shown to produce consistently reliable results for a wide range of field sizes and jaw configurations.

  14. Laboratory determination of gas-side mass transfer coefficients applicable to soil-venting systems for removing petroleum hydrocarbons from vadose-zone soils. Master's thesis

    SciTech Connect (OSTI)

    Van Valkenburg, M.E.

    1991-01-01

    Contamination of the subsurface environment by organic solvents has become a national problem. The EPA's Superfund list (40 CFR Part 300, 1990) continues to grow, with continual discovery of new hazardous waste sites. Various techniques are employed to remediate these sites, including excavation and removal of the contaminated soil for proper disposal, pumping and treatment of contaminated ground water and an organic phase if present, containment by slurried soil-bentonite cut-off barriers, in situ biological treatment of the organic wastes, and vadose zone soil venting for gas absorption of volatiles. Each technique, or combination, may have merit at a given site. The soil venting process, an inexpensive but relatively successful technique for removal of contaminants from the vadose (unsaturated) zone, is the focus of the research.

  15. f your soil has a high salinity content, the plants growing there will not be as vigorous as they would

    E-Print Network [OSTI]

    I f your soil has a high salinity content, the plants growing there will not be as vigorous as they would be in normal soils. Seeds will germinate poorly, if at all, and the plants will grow slowly much you water them. Routine soil testing can identify your soil's salinity levels and suggest measures

  16. Applying an Information Gathering Architecture to Netfind: A White Pages Tool for a Changing and Growing Internet

    E-Print Network [OSTI]

    Schwartz, Michael F.

    ], the Internet is one the fastest growing human-constructed phenomena in history. The explosive growth and Growing Internet Michael F. Schwartz, University of Colorado, Boulder (schwartz@cs.colorado.edu) Calton Pu on Networking The Internet is quickly becoming an indispensable means of communication and collaboration, based

  17. Mobile system for microwave removal of concrete surfaces

    DOE Patents [OSTI]

    White, Terry L. (Oak Ridge, TN); Bigelow, Timothy S. (Knoxville, TN); Schaich, Charles R. (Lenoir City, TN); Foster, Jr., Don (Knoxville, TN)

    1997-01-01

    A method and apparatus for the microwave removal of contaminated concrete surfaces. The apparatus comprises a housing adapted to pass over a support surface. The housing includes a waveguide for directing microwave energy to the surface at an angle maximizing absorption of microwave energy by the surface. The apparatus is further provided with a source of microwave energy operably associated with the waveguide, wherein the microwave energy has a frequency of between about 10.6 GHz and about 24 GHz and acts to remove the uppermost layer from the surface. The apparatus further includes a debris containment assembly comprising a vacuum assembly operably associated with the housing. The vacuum assembly is adapted to remove debris from the area adjacent the surface.

  18. Metal chelate process to remove pollutants from fluids

    DOE Patents [OSTI]

    Chang, S.G.T.

    1994-12-06

    The present invention relates to improved methods using an organic iron chelate to remove pollutants from fluids, such as flue gas. Specifically, the present invention relates to a process to remove NO[sub x] and optionally SO[sub 2] from a fluid using a metal ion (Fe[sup 2+]) chelate wherein the ligand is a dimercapto compound wherein the --SH groups are attached to adjacent carbon atoms (HS--C--C--SH) or (SH--C--CCSH) and contain a polar functional group so that the ligand of DMC chelate is water soluble. Alternatively, the DMC is covalently attached to a water insoluble substrate such as a polymer or resin, e.g., polystyrene. The chelate is regenerated using electroreduction or a chemical additive. The dimercapto compound bonded to a water insoluble substrate is also useful to lower the concentration or remove hazardous metal ions from an aqueous solution. 26 figures.

  19. Savannah River Site Waste Removal Program - Past, Present and Future

    SciTech Connect (OSTI)

    Saldivar, E.

    2002-02-25

    The Savannah River Site has fifty-one high level waste tanks in various phases of operation and closure. These tanks were originally constructed to receive, store, and treat the high level waste (HLW) created in support of the missions assigned by the Department of Energy (DOE). The Federal Facilities Agreement (FFA) requires the high level waste to be removed from the tanks and stabilized into a final waste form. Additionally, closure of the tanks following waste removal must be completed. The SRS HLW System Plan identifies the interfaces of safe storage, waste removal, and stabilization of the high level waste and the schedule for the closure of each tank. HLW results from the dissolution of irradiated fuel components. Desired nuclear materials are recovered and the byproducts are neutralized with NaOH and sent to the High Level Waste Tank Farms at the SRS. The HLW process waste clarifies in the tanks as the sludge settles, resulting in a layer of dense sludge with salt supernate settling above the sludge. Salt supernate is concentrated via evaporation into saltcake and NaOH liquor. This paper discusses the history of SRS waste removal systems, recent waste removal experiences, and the challenges facing future removal operations to enhance efficiency and cost effectiveness. Specifically, topics will include the evolution and efficiency of systems used in the 1960's which required large volumes of water to current systems of large centrifugal slurry pumps, with significant supporting infrastructure and safety measures. Interactions of this equipment with the waste tank farm operations requirements will also be discussed. The cost and time improvements associated with these present-day systems is a primary focus for the HLW Program.

  20. Compositions and methods for removing arsenic in water

    DOE Patents [OSTI]

    Gadgil, Ashok Jagannth (El Cerrito, CA)

    2011-02-22

    Compositions and methods and for contaminants from water are provided. The compositions comprise ferric hydroxide and ferric oxyhydride coated substrates for use in removing the contaminant from the water. Contacting water bearing the contaminant with the substrates can substantially reduce contaminant levels therein. Methods of oxidizing the contaminants in water to facilitate their removal by the ferric hydroxide and ferric oxyhydride coated substrates are also provided. The contaminants include, but are not limited to, arsenic, selenium, uranium, lead, cadmium, nickel, copper, zinc, chromium and vanadium, their oxides and soluble salts thereof.

  1. Method for removal of beryllium contamination from an article

    SciTech Connect (OSTI)

    Simandl, Ronald F.; Hollenbeck, Scott M.

    2012-12-25

    A method of removal of beryllium contamination from an article is disclosed. The method typically involves dissolving polyisobutylene in a solvent such as hexane to form a tackifier solution, soaking the substrate in the tackifier to produce a preform, and then drying the preform to produce the cleaning medium. The cleaning media are typically used dry, without any liquid cleaning agent to rub the surface of the article and remove the beryllium contamination below a non-detect level. In some embodiments no detectible residue is transferred from the cleaning wipe to the article as a result of the cleaning process.

  2. Methods of hydrotreating a liquid stream to remove clogging compounds

    DOE Patents [OSTI]

    Minderhoud, Johannes Kornelis [Amsterdam, NL; Nelson, Richard Gene [Katy, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Ryan, Robert Charles [Houston, TX; Nair, Vijay [Katy, TX

    2009-09-22

    A method includes producing formation fluid from a subsurface in situ heat treatment process. The formation fluid is separated to produce a liquid stream and a gas stream. At least a portion of the liquid stream is provided to a hydrotreating unit. At least a portion of selected in situ heat treatment clogging compositions in the liquid stream are removed to produce a hydrotreated liquid stream by hydrotreating at least a portion of the liquid stream at conditions sufficient to remove the selected in situ heat treatment clogging compositions.

  3. Method for the removal and recovery of mercury

    DOE Patents [OSTI]

    Easterly, C.E.; Vass, A.A.; Tyndall, R.L.

    1997-01-28

    The present invention is an enhanced method for the removal and recovery of mercury from mercury-contaminated matrices. The method involves contacting a mercury-contaminated matrix with an aqueous dispersant solution derived from specific intra-amoebic isolates to release the mercury from the mercury-contaminated matrix and emulsify the mercury; then, contacting the matrix with an amalgamating metal from a metal source to amalgamate the mercury to the amalgamating metal; removing the metallic source from the mercury-contaminated matrix; and heating the metallic source to vaporize the mercury in a closed system to capture the mercury vapors.

  4. Method for removing undesired particles from gas streams

    DOE Patents [OSTI]

    Durham, Michael Dean (Castle Rock, CO); Schlager, Richard John (Aurora, CO); Ebner, Timothy George (Westminster, CO); Stewart, Robin Michele (Arvada, CO); Hyatt, David E. (Denver, CO); Bustard, Cynthia Jean (Littleton, CO); Sjostrom, Sharon (Denver, CO)

    1998-01-01

    The present invention discloses a process for removing undesired particles from a gas stream including the steps of contacting a composition containing an adhesive with the gas stream; collecting the undesired particles and adhesive on a collection surface to form an aggregate comprising the adhesive and undesired particles on the collection surface; and removing the agglomerate from the collection zone. The composition may then be atomized and injected into the gas stream. The composition may include a liquid that vaporizes in the gas stream. After the liquid vaporizes, adhesive particles are entrained in the gas stream. The process may be applied to electrostatic precipitators and filtration systems to improve undesired particle collection efficiency.

  5. Sorbents for the oxidation and removal of mercury

    DOE Patents [OSTI]

    Olson, Edwin S.; Holmes, Michael J.; Pavlish, John Henry

    2014-09-02

    A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

  6. Sorbents for the oxidation and removal of mercury

    DOE Patents [OSTI]

    Olson, Edwin S. (Grand Forks, ND); Holmes, Michael J. (Thompson, ND); Pavlish, John H. (East Grand Forks, MN)

    2012-05-01

    A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

  7. Sorbents for the oxidation and removal of mercury

    DOE Patents [OSTI]

    Olson, Edwin S. (Grand Forks, ND); Holmes, Michael J. (Thompson, ND); Pavlish, John H. (East Grand Forks, MN)

    2008-10-14

    A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

  8. Environmental Impacts of Stover Removal in the Corn Belt

    SciTech Connect (OSTI)

    Alicia English; Wallace E. Tyner; Juan Sesmero; Phillip Owens; David Muth

    2012-08-01

    When considering the market for biomass from corn stover resources erosion and soil quality issues are important to consider. Removal of stover can be beneficial in some areas, especially when coordinated with other conservation practices, such as vegetative barrier strips and cover crops. However, benefits are highly dependent on several factors, namely if farmers see costs and benefits associated with erosion and the tradeoffs with the removal of biomass. This paper uses results from an integrated RUSLE2/WEPS model to incorporate six different regime choices, covering management, harvest and conservation, into simple profit maximization model to show these tradeoffs.

  9. Method for removing semiconductor layers from salt substrates

    DOE Patents [OSTI]

    Shuskus, Alexander J. (West Hartford, CT); Cowher, Melvyn E. (East Brookfield, MA)

    1985-08-27

    A method is described for removing a CVD semiconductor layer from an alkali halide salt substrate following the deposition of the semiconductor layer. The semiconductor-substrate combination is supported on a material such as tungsten which is readily wet by the molten alkali halide. The temperature of the semiconductor-substrate combination is raised to a temperature greater than the melting temperature of the substrate but less than the temperature of the semiconductor and the substrate is melted and removed from the semiconductor by capillary action of the wettable support.

  10. The Comparative Value of Cottonseed Hulls and Hay as Roughages for Growing Dairy Heifers. 

    E-Print Network [OSTI]

    Copeland, O. C. (Orlin Cephos)

    1932-01-01

    . DeMottier, Asst. Chemist Rural Home Research: R. L. Schwartz, B. S.. Asst. Chemist Jessie Whitacre, Ph. D.. Chief C. M. Pounders, B. S., Asst. Chemist Mary Anna Grimes, M. S.. Textiles Rorticulture: Elizabeth D. Terrill, M. A., Nutrition S. H... with grain, silage, and pasturage when available, proved to be slightly superior to cottonseed hulls as the sole dry roughage for growing dairy heifers. The more rapid growth of the hay group was made during the first 18 months of age, more especially...

  11. Solar Photovoltaic Economic Development: Building and Growing a Local PV Industry, August 2011 (Book)

    SciTech Connect (OSTI)

    Not Available

    2011-08-01

    The U.S. photovoltaic (PV) industry is forecast to grow, and it represents an opportunity for economic development and job creation in communities throughout the United States. This report helps U.S. cities evaluate economic opportunities in the PV industry. It serves as a guide for local economic development offices in evaluating their community?s competitiveness in the solar PV industry, assessing the viability of solar PV development goals, and developing strategies for recruiting and retaining PV companies to their areas.

  12. Technical note Barriers and opportunities for passive removal of indoor ozone

    E-Print Network [OSTI]

    Siegel, Jeffrey

    Technical note Barriers and opportunities for passive removal of indoor ozone Elliott T. Gall presents a Monte Carlo simulation to assess passive removal materials (PRMs) that remove ozone of homes in Houston, Texas, were taken from the literature and combined with back- ground ozone removal

  13. Pentek metal coating removal system: Baseline report; Greenbook (chapter)

    SciTech Connect (OSTI)

    1997-07-31

    The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

  14. Thief process for the removal of mercury from flue gas

    DOE Patents [OSTI]

    Pennline, Henry W. (Bethel Park, PA); Granite, Evan J. (Wexford, PA); Freeman, Mark C. (South Park Township, PA); Hargis, Richard A. (Canonsburg, PA); O'Dowd, William J. (Charleroi, PA)

    2003-02-18

    A system and method for removing mercury from the flue gas of a coal-fired power plant is described. Mercury removal is by adsorption onto a thermally activated sorbent produced in-situ at the power plant. To obtain the thermally activated sorbent, a lance (thief) is inserted into a location within the combustion zone of the combustion chamber and extracts a mixture of semi-combusted coal and gas. The semi-combusted coal has adsorptive properties suitable for the removal of elemental and oxidized mercury. The mixture of semi-combusted coal and gas is separated into a stream of gas and semi-combusted coal that has been converted to a stream of thermally activated sorbent. The separated stream of gas is recycled to the combustion chamber. The thermally activated sorbent is injected into the duct work of the power plant at a location downstream from the exit port of the combustion chamber. Mercury within the flue gas contacts and adsorbs onto the thermally activated sorbent. The sorbent-mercury combination is removed from the plant by a particulate collection system.

  15. Particulate contamination removal from wafers using plasmas and mechanical agitation

    DOE Patents [OSTI]

    Selwyn, Gary S. (Los Alamos, NM)

    1998-01-01

    Particulate contamination removal from wafers using plasmas and mechanical agitation. The present invention includes the use of plasmas with mechanical agitation for removing particulate matter from the surface of a wafer. The apparatus hereof comprises a mechanical activator, at least one conducting contact pin for transferring the vibration from the activator to the wafer, clamp fingers that maintain the wafer's position, and means for generating a plasma in the vicinity of the surface of the wafer, all parts of the cleaning apparatus except the mechanical activator and part of the contact pin being contained inside the processing chamber. By exposing a wafer to a plasma and providing motion thereto in a direction perpendicular to its surface, the bonding between the particulate matter and the surface may be overcome. Once free of the wafer surface, the particulates become charged by electrons from the plasma and are drawn into the plasma by attractive forces which keep them from redepositing. The introduction of a flowing gas through the plasma sweeps the particulates away from the wafer and out of the plasma. The entire surface is cleaned during one cleaning step. The use of an rf plasma to accomplish the particulate removal was found to remove more than 90% of the particulates.

  16. Particulate contamination removal from wafers using plasmas and mechanical agitation

    DOE Patents [OSTI]

    Selwyn, G.S.

    1998-12-15

    Particulate contamination removal from wafers is disclosed using plasmas and mechanical agitation. The present invention includes the use of plasmas with mechanical agitation for removing particulate matter from the surface of a wafer. The apparatus hereof comprises a mechanical activator, at least one conducting contact pin for transferring the vibration from the activator to the wafer, clamp fingers that maintain the wafer`s position, and means for generating a plasma in the vicinity of the surface of the wafer, all parts of the cleaning apparatus except the mechanical activator and part of the contact pin being contained inside the processing chamber. By exposing a wafer to a plasma and providing motion thereto in a direction perpendicular to its surface, the bonding between the particulate matter and the surface may be overcome. Once free of the wafer surface, the particulates become charged by electrons from the plasma and are drawn into the plasma by attractive forces which keep them from redepositing. The introduction of a flowing gas through the plasma sweeps the particulates away from the wafer and out of the plasma. The entire surface is cleaned during one cleaning step. The use of an rf plasma to accomplish the particulate removal was found to remove more than 90% of the particulates. 4 figs.

  17. Removal of Pollutants by Atmospheric Non Thermal Plasmas

    E-Print Network [OSTI]

    Khacef, Ahmed; Pouvesle, Jean Michel; Van, Tiep Le

    2008-01-01

    Results on the application of non thermal plasmas in two environmentally important fields: oxidative removal of VOC and NOx in excess of oxygen were presented. The synergetic application of a plasma-catalytic treatment of NOx in excess of oxygen is also described.

  18. On automated prepared statement generation to remove SQL injection vulnerabilities

    E-Print Network [OSTI]

    Xie, Tao

    On automated prepared statement generation to remove SQL injection vulnerabilities Stephen Thomas in revised form 5 August 2008 Accepted 8 August 2008 Available online 27 September 2008 Keywords: SQL vulnerabilities were SQL injection vulnerabilities (SQLIVs). This paper presents an algorithm of prepared

  19. Magnetic process for removing heavy metals from water employing magnetites

    DOE Patents [OSTI]

    Prenger, F. Coyne; Hill, Dallas D.; Padilla, Dennis D.; Wingo, Robert M.; Worl, Laura A.; Johnson, Michael D.

    2003-07-22

    A process for removing heavy metals from water is provided. The process includes the steps of introducing magnetite to a quantity of water containing heavy metal. The magnetite is mixed with the water such that at least a portion of, and preferably the majority of, the heavy metal in the water is bound to the magnetite. Once this occurs the magnetite and absorbed metal is removed from the water by application of a magnetic field. In most applications the process is achieved by flowing the water through a solid magnetized matrix, such as steel wool, such that the magnetite magnetically binds to the solid matrix. The magnetized matrix preferably has remnant magnetism, but may also be subject to an externally applied magnetic field. Once the magnetite and associated heavy metal is bound to the matrix, it can be removed and disposed of, such as by reverse water or air and water flow through the matrix. The magnetite may be formed in-situ by the addition of the necessary quantities of Fe(II) and Fe(III) ions, or pre-formed magnetite may be added, or a combination of seed and in-situ formation may be used. The invention also relates to an apparatus for performing the removal of heavy metals from water using the process outlined above.

  20. Magnetic process for removing heavy metals from water employing magnetites

    DOE Patents [OSTI]

    Prenger, F. Coyne; Hill, Dallas D.

    2006-12-26

    A process for removing heavy metals from water is provided. The process includes the steps of introducing magnetite to a quantity of water containing heavy metal. The magnetite is mixed with the water such that at least a portion of, and preferably the majority of, the heavy metal in the water is bound to the magnetite. Once this occurs the magnetite and absorbed metal is removed from the water by application of a magnetic field. In most applications the process is achieved by flowing the water through a solid magnetized matrix, such as steel wool, such that the magnetite magnetically binds to the solid matrix. The magnetized matrix preferably has remnant magnetism, but may also be subject to an externally applied magnetic field. Once the magnetite and associated heavy metal is bound to the matrix, it can be removed and disposed of, such as by reverse water or air and water flow through the matrix. The magnetite may be formed in-situ by the addition of the necessary quantities of Fe(II) and Fe(III) ions, or pre-formed magnetite may be added, or a combination of seed and in-situ formation may be used. The invention also relates to an apparatus for performing the removal of heavy metals from water using the process outlined above.

  1. Process for removing polymer-forming impurities from naphtha fraction

    DOE Patents [OSTI]

    Kowalczyk, D.C.; Bricklemyer, B.A.; Svoboda, J.J.

    1983-12-27

    Polymer precursor materials are vaporized without polymerization or are removed from a raw naphtha fraction by passing the raw naphtha to a vaporization zone and vaporizing the naphtha in the presence of a wash oil while stripping with hot hydrogen to prevent polymer deposits in the equipment. 2 figs.

  2. Process for removing polymer-forming impurities from naphtha fraction

    DOE Patents [OSTI]

    Kowalczyk, Dennis C. (Pittsburgh, PA); Bricklemyer, Bruce A. (Avonmore, PA); Svoboda, Joseph J. (Pittsburgh, PA)

    1983-01-01

    Polymer precursor materials are vaporized without polymerization or are removed from a raw naphtha fraction by passing the raw naphtha to a vaporization zone (24) and vaporizing the naphtha in the presence of a wash oil while stripping with hot hydrogen to prevent polymer deposits in the equipment.

  3. Apparatus for removably holding a plurality of microballoons

    DOE Patents [OSTI]

    Jorgensen, B.S.

    1984-06-05

    The present invention relates generally to the manipulation of microballoons and more particularly to an apparatus for removably holding a plurality of microballoons in order to more efficiently carry out the filling of the microballoons with a known quantity of gas.

  4. Calf Removal: A Way to Stimulate Reproduction in Cows 

    E-Print Network [OSTI]

    Sprott, L. R.

    2003-10-08

    Cows that are slow to breed or fail to breed are costly to producers. One of the factors that delays the resumption of estrous activity in a cow--and subsequent breeding--is nursing stress. Removing a calf from a dam, either short...

  5. GROUNDWATER NITRATE REMOVAL CAPACITY OF RIPARIAN ZONES IN

    E-Print Network [OSTI]

    Gold, Art

    GROUNDWATER NITRATE REMOVAL CAPACITY OF RIPARIAN ZONES IN URBANIZING WATERSHEDS BY TARA KIMBERLY the watershed, however, is not well understood. Nitrate in groundwater moving through the "biologically active and geomorphology of riparian zones, potentially changing riparian groundwater denitrification capacity. Little work

  6. Apparatuses and methods for removal of ink buildup

    DOE Patents [OSTI]

    Cudzinovic, Michael; Pass, Thomas; Rogers, Rob; Sun, Ray-Hon; Sun, Sheng; Wahlstrom, Ben; Fuhrman, Dennis Jason; Altendorf, Kyle David

    2013-03-12

    A substrate patterning method including the steps of spraying ink on a surface of a substrate, the spraying of the ink resulting in an overspray of excess ink past an edge of the substrate; changing a temperature of the excess ink to cause a change in a viscosity of the excess ink; and removing the excess ink having the changed viscosity.

  7. Mercury removal in utility wet scrubber using a chelating agent

    DOE Patents [OSTI]

    Amrhein, Gerald T. (Louisville, OH)

    2001-01-01

    A method for capturing and reducing the mercury content of an industrial flue gas such as that produced in the combustion of a fossil fuel or solid waste adds a chelating agent, such as ethylenediaminetetraacetic acid (EDTA) or other similar compounds like HEDTA, DTPA and/or NTA, to the flue gas being scrubbed in a wet scrubber used in the industrial process. The chelating agent prevents the reduction of oxidized mercury to elemental mercury, thereby increasing the mercury removal efficiency of the wet scrubber. Exemplary tests on inlet and outlet mercury concentration in an industrial flue gas were performed without and with EDTA addition. Without EDTA, mercury removal totaled 42%. With EDTA, mercury removal increased to 71%. The invention may be readily adapted to known wet scrubber systems and it specifically provides for the removal of unwanted mercury both by supplying S.sup.2- ions to convert Hg.sup.2+ ions into mercuric sulfide (HgS) and by supplying a chelating agent to sequester other ions, including but not limited to Fe.sup.2+ ions, which could otherwise induce the unwanted reduction of Hg.sup.2+ to the form, Hg.sup.0.

  8. Finding mold removal directions using graphics hardware Rahul Khardekar

    E-Print Network [OSTI]

    McMains, Sara

    Finding mold removal directions using graphics hardware Rahul Khardekar University of California, Berkeley Sara McMains University of California, Berkeley 1 Introduction In molding and casting manufacturing processes, molten raw ma- terial is shaped in molds from which the resulting part must be re

  9. Energy Savings for CO2 Removal in Ammonia Plants 

    E-Print Network [OSTI]

    Pouilliart, R.; Van Hecke, F. C.

    1981-01-01

    An exergy analysis of carbonate solution C02 removal systems which use solution flashing shows that there is no energy saving by using a mechanical thermocompressor instead of a steam-jet ejector. In a 1000 ShT/D ammonia plant an energy saving...

  10. Process for removing sulfur from sulfur-containing gases

    DOE Patents [OSTI]

    Rochelle, Gary T. (Austin, TX); Jozewicz, Wojciech (Chapel Hill, NC)

    1989-01-01

    The present disclosure relates to improved processes for treating hot sulfur-containing flue gas to remove sulfur therefrom. Processes in accorda The government may own certain rights in the present invention pursuant to EPA Cooperative Agreement CR 81-1531.

  11. User-guided Pedestrian and Object Removal Antonio Haro

    E-Print Network [OSTI]

    Haro, Antonio

    User-guided Pedestrian and Object Removal Antonio Haro Nokia 425 West Randolph Street Chicago, IL of locations around the world. While the focus is on capturing streets and buildings, pedestrians are commonly captured. Pedestrian faces are identified and blurred in different sys- tems to address privacy concerns

  12. Investigating the Use of Biosorbents to Remove Arsenic from Water 

    E-Print Network [OSTI]

    Erapalli, Shreyas

    2011-02-22

    , As (III), and arsenate, As (V), from water. Batch reactors were employed to assess the percent removal, reaction kinetics, adsorption capacity, and desorption of each arsenic species onto/from biosorbents under pH buffered and non?buffered conditions...

  13. Method for removal of mercury from various gas streams

    DOE Patents [OSTI]

    Granite, E.J.; Pennline, H.W.

    2003-06-10

    The invention provides for a method for removing elemental mercury from a fluid, the method comprising irradiating the mercury with light having a wavelength of approximately 254 nm. The method is implemented in situ at various fuel combustion locations such as power plants and municipal incinerators.

  14. Guide wire extension for shape memory polymer occlusion removal devices

    SciTech Connect (OSTI)

    Maitland, Duncan J.; Small, IV, Ward; Hartman, Jonathan

    2009-11-03

    A flexible extension for a shape memory polymer occlusion removal device. A shape memory polymer instrument is transported through a vessel via a catheter. A flexible elongated unit is operatively connected to the distal end of the shape memory polymer instrument to enhance maneuverability through tortuous paths en route to the occlusion.

  15. Potential Supply Impacts of Removal of 1-Pound RVP Waiver

    E-Print Network [OSTI]

    Patzek, Tadeusz W.

    trends, and current laws and regulations. The EIA's Annual Energy Outlook 2002 (AEO2002) is usedPotential Supply Impacts of Removal of 1-Pound RVP Waiver September 2002 #12;ii Energy Information by the Office of Oil and Gas of the Energy Information Administration. General questions concerning the report

  16. Columbia River Channel Improvement Project Rock Removal Blasting: Monitoring Plan

    SciTech Connect (OSTI)

    Carlson, Thomas J.; Johnson, Gary E.

    2010-01-29

    This document provides a monitoring plan to evaluate take as outlined in the National Marine Fisheries Service 2002 Biological Opinion for underwater blasting to remove rock from the navigation channel for the Columbia River Channel Improvement Project. The plan was prepared by the Pacific Northwest National Laboratory (PNNL) for the U.S. Army Corps of Engineers (USACE), Portland District.

  17. Detroit Edison's Fermi 1 - Preparation for Reactor Removal

    SciTech Connect (OSTI)

    Swindle, Danny [Sargent and Lundy Engineers, LLC, 55 E. Monroe Street, Chicago, IL 60603 (United States)

    2008-01-15

    This paper is intended to provide information about the ongoing decommissioning tasks at Detroit Edison's Fermi 1 plant, and in particular, the work being performed to prepare the reactor for removal and disposal. In 1972 Fermi 1 was shutdown and the fuel returned to the Atomic Energy Commission. By the end of 1975, a retirement plan was prepared, the bulk sodium removed, and the plant placed in a safe store condition. The plant systems were left isolated with the sodium containing systems inert with carbon dioxide in an attempt to form a carbonate layer, thus passivating the underlying reactive sodium. In 1996, Detroit Edison determined to evaluate the condition of the plant and to make recommendations in relation to the Fermi 1 future plans. At the end of 1997 approval was obtained to remove the bulk asbestos and residual alkali-metals (i.e., sodium and sodium potassium (NaK)). In 2000, full nuclear decommissioning of the plant was approved. To date, the bulk asbestos insulation has been removed, and the only NaK remaining is located in six capillary instrument tubes. The remaining sodium is contained within the reactor, two of the three primary loops, and miscellaneous removed pipes and equipment to be processed. The preferred method for removing or reacting sodium at Fermi 1 is by injecting superheated steam into a heated, nitrogen inert system. The byproducts of this reaction are caustic sodium hydroxide, hydrogen gas, and heat. The decision was made to separate the three primary loops from the reactor for better control prior to processing each loop and the reactor separately. The first loop has already been processed. The main focus is now to process the reactor to allow removal and disposal of the Class C waste prior to the anticipated June 2008 closure of the Barnwell radioactive waste disposal facility located in South Carolina. Lessons learnt are summarized and concern: the realistic schedule and adherence to the schedule, time estimates, personnel accountability, back up or fill in work, work packages, condensation control, radiological contamination control, and organization of the waste stream.

  18. Simulating dam removal with a 1D hydraulic model: Accuracy and techniques for reservoir erosion and downstream deposition at the Chiloquin Dam removal

    E-Print Network [OSTI]

    Tullos, Desiree

    Simulating dam removal with a 1D hydraulic model: Accuracy and techniques for reservoir erosion and downstream deposition at the Chiloquin Dam removal Desiree Tullos1 , Matt Cox1 , Cara Walter1 1 Department are often used to reduce uncertainty regarding the outcomes of dam removal, though the accuracy

  19. On atomic structure of Ge huts growing on the Ge/Si(001) wetting layer

    SciTech Connect (OSTI)

    Arapkina, Larisa V.; Yuryev, Vladimir A. [A. M. Prokhorov General Physics Institute of the Russian Academy of Sciences, 38 Vavilov Street, Moscow, 119991 (Russian Federation)] [A. M. Prokhorov General Physics Institute of the Russian Academy of Sciences, 38 Vavilov Street, Moscow, 119991 (Russian Federation)

    2013-09-14

    Structural models of growing Ge hut clusters—pyramids and wedges—are proposed on the basis of data of recent STM investigations of nucleation and growth of Ge huts on the Si(001) surface in the process of molecular beam epitaxy. It is shown that extension of a hut base along <110> directions goes non-uniformly during the cluster growth regardless of its shape. Growing pyramids, starting from the second monolayer, pass through cyclic formation of slightly asymmetrical and symmetrical clusters, with symmetrical ones appearing after addition of every fourth monolayer. We suppose that pyramids of symmetrical configurations composed by 2, 6, 10, etc., monolayers over the wetting layer are more stable than asymmetrical ones. This might explain less stability of pyramids in comparison with wedges in dense arrays forming at low temperatures of Ge deposition. Possible nucleation processes of pyramids and wedges on wetting layer patches from identical embryos composed by 8 dimers through formation of 1 monolayer high 16-dimer nuclei different only in their symmetry is discussed. Schematics of these processes are presented. It is concluded from precise STM measurements that top layers of wetting layer patches are relaxed when huts nucleate on them.

  20. Effect of different ratios of sodium to chloride using isokalemic diets for growing and finishing swine raised during hot weather 

    E-Print Network [OSTI]

    Serna-Saldivar, Sergio Othon

    1982-01-01

    ABSTBXCT Effect of Different Ratios of Sodium to Chloride Using Isokalemic Diets for Growing and Pinishing Swine Raised During Hot Weather {Bay 1982) Sergio Othon Serna-Saldivar B. S, Inn tituto Tecnologico y de Estudios Superiores de monterrey...

  1. Effects of Residual Feed Intake Classification on Temperament, Carcass Composition, and Feeding Behavior Traits in Growing Santa Gertrudis Heifers 

    E-Print Network [OSTI]

    Ramirez, Justin A

    2014-04-16

    Objectives of this study were to evaluate the associations of feed intake, feeding behavior, temperament, and carcass composition with performance and feed efficiency traits in growing heifers. Santa Gertrudis heifers (n ...

  2. Exploring the Impact of Growing Up in a Single Parent Family from an Adult Perspective: An Interpretative Phenomenological Analysis 

    E-Print Network [OSTI]

    Walsh, Annabel

    2012-05-25

    This study explores the impact that growing up in a single parent family from a young age has on adulthood. Previous quantitative research suggests that children raised in this family structure encounter more difficulties ...

  3. Freezing / Thawing mammalian cells (AG/2-96) 1. Grow cells to confluency in 100 mm plates.

    E-Print Network [OSTI]

    Ghosh, Anirvan

    Freezing / Thawing mammalian cells (AG/2-96) Freezing: 1. Grow cells to confluency in 100 mm plates ml per vial), seal, place between styrofoam tube holders, and freeze at -70 C. 7. Transfer tubes

  4. www.rtands.com Railway Track & Structures March 2009 37 s rail transport continues to grow in popularity, so does

    E-Print Network [OSTI]

    Farritor, Shane

    www.rtands.com Railway Track & Structures March 2009 37 A s rail transport continues to grow is protected from debris, rain and freezing temperatures, the more smoothly it flows." Barr cites the findings

  5. Method of synthesizing and growing copper-indium-diselenide (CuInSe/sub 2/) crystals

    DOE Patents [OSTI]

    Ciszek, T.F.

    1984-11-29

    A process for preparing CuInSe/sub 2/ crystals includes melting a sufficient quantity of B/sub 2/O/sub 2/ along with stochiometric quantities of Cu, In, and Se in a crucible in a high-pressure atmosphere of inert gas to encapsulate the CuInSe/sub 2/ melt and confine the Se to the crucible. Additional Se in the range of 1.8 to 2.2% over the stochiometric quantity is preferred to make up for small amounts of Se lost in the process. The melt can then be cooled slowly to form the crystal as direct solidification, or the crystal can be grown by inserting a seed crystal through the B/sub 2/O/sub 3/ encapsulate into contact with the CuInSe/sub 2/ melt and withdrawing the seed upwardly to grow the crystal thereon from the melt.

  6. Forest phenology and a warmer climate - Growing season extension in relation to climatic provenance

    SciTech Connect (OSTI)

    Gunderson, Carla A [ORNL; Edwards, Nelson T [ORNL; Walker, Ashley V [ORNL; O'Hara, Keiran H [ORNL; Campion, Christina M [ORNL; Hanson, Paul J [ORNL

    2012-01-01

    Predicting forest responses to warming climates relies on assumptions about niche and temperature sensitivity that remain largely untested. Observational studies have related current and historical temperatures to phenological shifts, but experimental evidence is sparse, particularly for autumn responses. A five-year field experiment exposed four deciduous forest species from contrasting climates (Liquidambar styraciflua, Quercus rubra, Populus grandidentata, and Betula alleghaniensis) to air temperatures 2 and 4 C above ambient controls. Impacts of year-round warming on bud burst (BB), senescence and abscission were evaluated in relation to thermal provenance. Leaves emerged earlier in all species, by an average of 6-9 days at +2 and +4 C. Magnitude of advance varied with species and year, but was larger for the first 2 C increment than the second. The effect of warming increased with early BB, favoring Liquidambar, from the warmest climate, but even BB in northern species advanced, despite temperatures well beyond those of the realized niche. Treatment differences in BB were poorly explained by temperature sums, which increased with treatment. In autumn, chlorophyll was retained an average of 4 and 7 days longer in +2 and +4 C treatments, and abscission delayed by 8 and 13 days. Species differences in autumn responses were marginally significant. Growing seasons in the warmer atmospheres were 6 - 28 days longer, with the least impact in Quercus. Results are compared with a 16-year record of canopy onset and offset in a nearby upland deciduous forest, where BB showed similar responsiveness to spring temperatures (2 - 4 days C-1). Offset dates in the stand tracked August-September temperatures, except when late summer drought caused premature senescence. The common garden-like experimental approach provides evidence that warming alone extends the growing season, at both ends, even if stand-level impacts are complicated by other environmental factors.

  7. The CNG process: Acid gas removal with liquid carbon dioxide

    SciTech Connect (OSTI)

    Liu, Y.C.; Auyang, L.; Brown, W.R.

    1987-01-01

    The CNG acid gas removal process has two unique features: the absorption of sulfur-containing compounds and other trace contaminants with liquid carbon dioxide, and the regeneration of pure liquid carbon dioxide by triple-point crystallization. The process is especially suitable for treating gases which contain large amounts of carbon dioxide and much smaller amounts (relative to carbon dioxide) of hydrogen sulfide. Capital and energy costs are lower than conventional solvent processes. Further, products of the CNG process meet stringent purity specifications without undue cost penalties. A process demonstration unit has been constructed and operated to demonstrate the two key steps of the CNG process. Hydrogen sulfide and carbonyl sulfide removal from gas streams with liquid carbon dioxide absorbent to sub-ppm concentrations has been demonstrated. The production of highly purified liquid carbon dioxide (less than 0.1 ppm total contaminant) by triple-point crystallization also has been demonstrated.

  8. Removal of arsenic compounds from spent catecholated polymer

    DOE Patents [OSTI]

    Fish, Richard H. (Berkeley, CA)

    1985-01-01

    Described is a process for removing arsenic from petroliferous derived liquids by contacting said liquid at an elevated temperature with a divinylbenzene-crosslinked polystyrene having catechol ligands anchored thereon. Also, described is a process for regenerating spent catecholated polystyrene by removal of the arsenic bound to it from contacting petroliferous liquid as described above and involves: a. treating said spent catecholated polystyrene, at a temperature in the range of about 20.degree. to 100.degree. C. with an aqueous solution of at least one carbonate and/or bicarbonate of ammonium, alkali and alkaline earth metals, said solution having a pH between about 8 and 10 and, b. separating the solids and liquids from each other. Preferably the regeneration treatment is in two steps wherein step (a) is carried out with an aqueous alcoholic carbonate solution containing lower alkyl alcohol, and, steps (a) and (b) are repeated using a bicarbonate.

  9. Negative kinetic energy term of general relativity and its removing

    E-Print Network [OSTI]

    T. Mei

    2009-03-30

    We first present a new Lagrangian of general relativity, which can be divided into kinetic energy term and potential energy term. Taking advantage of vierbein formalism, we reduce the kinetic energy term to a sum of five positive terms and one negative term. Some gauge conditions removing the negative kinetic energy term are discussed. Finally, we present a Lagrangian that only include positive kinetic energy terms. To remove the negative kinetic energy term leads to a new field equation of general relativity in which there are at least five equations of constraint and at most five dynamical equations, this characteristic is different from the normal Einstein field equation in which there are four equations of constraint and six dynamical equations.

  10. Apparatus for removing hydrocarbon contaminants from solid materials

    DOE Patents [OSTI]

    Bala, G.A.; Thomas, C.P.

    1996-02-13

    A system is described for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste). 4 figs.

  11. Method for removing hydrocarbon contaminants from solid materials

    DOE Patents [OSTI]

    Bala, Gregory A. (Idaho Falls, ID); Thomas, Charles P. (Idaho Falls, ID)

    1995-01-01

    A system for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste).

  12. Apparatus for removing hydrocarbon contaminants from solid materials

    DOE Patents [OSTI]

    Bala, Gregory A. (Idaho Falls, ID); Thomas, Charles P. (Idaho Falls, ID)

    1996-01-01

    A system for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste).

  13. Methods of using adsorption media for separating or removing constituents

    DOE Patents [OSTI]

    Tranter, Troy J. (Idaho Falls, ID); Herbst, R. Scott (Idaho Falls, ID); Mann, Nicholas R. (Blackfoot, ID); Todd, Terry A. (Aberdeen, ID)

    2011-10-25

    Methods of using an adsorption medium to remove at least one constituent from a feed stream. The method comprises contacting an adsorption medium with a feed stream comprising at least one constituent and removing the at least one constituent from the feed stream. The adsorption medium comprises a polyacrylonitrile (PAN) matrix and at least one metal hydroxide homogenously dispersed therein. The adsorption medium may comprise from approximately 15 wt % to approximately 90 wt % of the PAN and from approximately 10 wt % to approximately 85 wt % of the at least one metal hydroxide. The at least one metal hydroxide may be selected from the group consisting of ferric hydroxide, zirconium hydroxide, lanthanum hydroxide, cerium hydroxide, titanium hydroxide, copper hydroxide, antimony hydroxide, and molybdenum hydroxide.

  14. Removal of field and embedded metal by spin spray etching

    DOE Patents [OSTI]

    Contolini, R.J.; Mayer, S.T.; Tarte, L.A.

    1996-01-23

    A process of removing both the field metal, such as copper, and a metal, such as copper, embedded into a dielectric or substrate at substantially the same rate by dripping or spraying a suitable metal etchant onto a spinning wafer to etch the metal evenly on the entire surface of the wafer. By this process the field metal is etched away completely while etching of the metal inside patterned features in the dielectric at the same or a lesser rate. This process is dependent on the type of chemical etchant used, the concentration and the temperature of the solution, and also the rate of spin speed of the wafer during the etching. The process substantially reduces the metal removal time compared to mechanical polishing, for example, and can be carried out using significantly less expensive equipment. 6 figs.

  15. Criticality safety aspects of K-25 Building uranium deposit removal

    SciTech Connect (OSTI)

    Haire, M.J.; Jordan, W.C. [Oak Ridge National Lab., TN (United States); Ingram, J.C. III; Stinnet, E.C. Jr. [Oak Ridge K-25 Site, TN (United States)

    1995-12-31

    The K-25 Building of the Oak Ridge Gaseous Diffusion Plant (now the K-25 Site) went into operation during World War II as the first large scale production plant to separate {sup 235}U from uranium by the gaseous diffusion process. It operated successfully until 1964, when it was placed in a stand-by mode. The Department of Energy has initiated a decontamination and decommissioning program. The primary objective of the Deposit Removal (DR) Project is to improve the nuclear criticality safety of the K-25 Building by removing enriched uranium deposits from unfavorable-geometry process equipment to below minimum critical mass. The method utilized to accomplish this are detailed in this report.

  16. Methods for removing contaminant matter from a porous material

    DOE Patents [OSTI]

    Fox, Robert V. (Idaho Falls, ID) [Idaho Falls, ID; Avci, Recep (Bozeman, MT) [Bozeman, MT; Groenewold, Gary S. (Idaho Falls, ID) [Idaho Falls, ID

    2010-11-16

    Methods of removing contaminant matter from porous materials include applying a polymer material to a contaminated surface, irradiating the contaminated surface to cause redistribution of contaminant matter, and removing at least a portion of the polymer material from the surface. Systems for decontaminating a contaminated structure comprising porous material include a radiation device configured to emit electromagnetic radiation toward a surface of a structure, and at least one spray device configured to apply a capture material onto the surface of the structure. Polymer materials that can be used in such methods and systems include polyphosphazine-based polymer materials having polyphosphazine backbone segments and side chain groups that include selected functional groups. The selected functional groups may include iminos, oximes, carboxylates, sulfonates, .beta.-diketones, phosphine sulfides, phosphates, phosphites, phosphonates, phosphinates, phosphine oxides, monothio phosphinic acids, and dithio phosphinic acids.

  17. Commercial Submersible Mixing Pump For SRS Tank Waste Removal - 15223

    SciTech Connect (OSTI)

    Hubbard, M.

    2015-01-12

    The Savannah River Site Tank Farms have 45 active underground waste tanks used to store and process nuclear waste materials. There are 4 different tank types, ranging in capacity from 2839 m3 to 4921 m3 (750,000 to 1,300,000 gallons). Eighteen of the tanks are older style and do not meet all current federal standards for secondary containment. The older style tanks are the initial focus of waste removal efforts for tank closure and are referred to as closure tanks. Of the original 51 underground waste tanks, six of the original 24 older style tanks have completed waste removal and are filled with grout. The insoluble waste fraction that resides within most waste tanks at SRS requires vigorous agitation to suspend the solids within the waste liquid in order to transfer this material for eventual processing into glass filled canisters at the Defense Waste Processing Facility (DWPF). SRS suspends the solid waste by use of recirculating mixing pumps. Older style tanks generally have limited riser openings which will not support larger mixing pumps, since the riser access is typically 58.4 cm (23 inches) in diameter. Agitation for these tanks has been provided by four long shafted standard slurry pumps (SLP) powered by an above tank 112KW (150 HP) electric motor. The pump shaft is lubricated and cooled in a pressurized water column that is sealed from the surrounding waste in the tank. Closure of four waste tanks has been accomplished utilizing long shafted pump technology combined with heel removal using multiple technologies. Newer style waste tanks at SRS have larger riser openings, allowing the processing of waste solids to be accomplished with four large diameter SLPs equipped with 224KW (300 HP) motors. These tanks are used to process the waste from closure tanks for DWPF. In addition to the SLPs, a 224KW (300 HP) submersible mixer pump (SMP) has also been developed and deployed within older style tanks. The SMPs are product cooled and product lubricated canned motor pumps designed to fit within available risers and have significant agitation capabilities to suspend waste solids. Waste removal and closure of two tanks has been accomplished with agitation provided by 3 SMPs installed within the tanks. In 2012, a team was assembled to investigate alternative solids removal technologies to support waste removal for closing tanks. The goal of the team was to find a more cost effective approach that could be used to replace the current mixing pump technology. This team was unable to identify an alternative technology outside of mixing pumps to support waste agitation and removal from SRS waste tanks. However, the team did identify a potentially lower cost mixing pump compared to the baseline SLPs and SMPs. Rather than using the traditional procurement using an engineering specification, the team proposed to seek commercially available submersible mixer pumps (CSMP) as alternatives to SLPs and SMPs. SLPs and SMPs have a high procurement cost and the actual cost of moving pumps between tanks has shown to be significantly higher than the original estimates that justified the reuse of SMPs and SLPs. The team recommended procurement of “off-the-shelf” industry pumps which may be available for significant savings, but at an increased risk of failure and reduced operating life in the waste tank. The goal of the CSMP program is to obtain mixing pumps that could mix from bulk waste removal through tank closure and then be abandoned in place as part of tank closure. This paper will present the development, progress and relative advantages of the CSMP.

  18. Method for removing undesired particles from gas streams

    DOE Patents [OSTI]

    Durham, M.D.; Schlager, R.J.; Ebner, T.G.; Stewart, R.M.; Hyatt, D.E.; Bustard, C.J.; Sjostrom, S.

    1998-11-10

    The present invention discloses a process for removing undesired particles from a gas stream including the steps of contacting a composition containing an adhesive with the gas stream; collecting the undesired particles and adhesive on a collection surface to form an aggregate comprising the adhesive and undesired particles on the collection surface; and removing the agglomerate from the collection zone. The composition may then be atomized and injected into the gas stream. The composition may include a liquid that vaporizes in the gas stream. After the liquid vaporizes, adhesive particles are entrained in the gas stream. The process may be applied to electrostatic precipitators and filtration systems to improve undesired particle collection efficiency. 11 figs.

  19. An alternative to removing lead-based paint: Overcoating

    SciTech Connect (OSTI)

    Vernon, L.S.

    1996-02-01

    The case of repairing a municipal water tank coated with lead-based paint (LBP) is used to illustrate some of the benefits of overcoating, a possible alternative to removing failing paint. The paper discusses data regarding performance of the waterborne acrylic used in the case study, briefly reviews revisions to specifications for the coating`s use, and offers some costs by which to compare use of a waterborne encapsulant such as that used in the case study with either removal and recoating or use of a solvent-borne encapsulant. A surface-tolerant, water-based, corrosion-resistant acrylic was selected to overcoat the LBP. By cleaning and overcoating the existing adherent LBP using the acrylic coating, chances of lead exposure to workers and the public were reduced. Eliminating abrasive blasting and the need for full containment saved about $80,000 to $100,000.

  20. Method for removing hydrocarbon contaminants from solid materials

    DOE Patents [OSTI]

    Bala, G.A.; Thomas, C.P.

    1995-10-03

    A system is described for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste). 4 figs.

  1. Process for removing sulfate anions from waste water

    DOE Patents [OSTI]

    Nilsen, David N. (Lebanon, OR); Galvan, Gloria J. (Albany, OR); Hundley, Gary L. (Corvallis, OR); Wright, John B. (Albany, OR)

    1997-01-01

    A liquid emulsion membrane process for removing sulfate anions from waste water is disclosed. The liquid emulsion membrane process includes the steps of: (a) providing a liquid emulsion formed from an aqueous strip solution and an organic phase that contains an extractant capable of removing sulfate anions from waste water; (b) dispersing the liquid emulsion in globule form into a quantity of waste water containing sulfate anions to allow the organic phase in each globule of the emulsion to extract and absorb sulfate anions from the waste water and (c) separating the emulsion including its organic phase and absorbed sulfate anions from the waste water to provide waste water containing substantially no sulfate anions.

  2. Process for removing carbonyl-sulfide from liquid hydrocarbon feedstocks

    SciTech Connect (OSTI)

    Debras, G.L.G.; DeClippeleir, G.E.M.J.; Cahen, R.M.

    1986-09-23

    A process is described for removing carbonyl sulfide from a liquid olefinic hydrocarbon feedstock comprising: (a) passing the hydrocarbon feedstock over an absorbent material comprising zinc oxide and a promoter selected from the group consisting of alumina, silico-aluminas and any combination thereof wherein the promoter is present in amounts from about 3 to about 15 percent by weight of the absorbent material; and (b) recovering a liquid olefinic hydrocarbon stream having a substantially reduced carbonyl sulfide content.

  3. Microbial removal of no.sub.x from gases

    DOE Patents [OSTI]

    Sublette, Kerry L. (Tulsa, OK)

    1991-01-01

    Disclosed is a process by which a gas containing nitric oxide is contacted with an anaerobic microbial culture of denitrifying bacteria to effect the chemical reduction of the nitric oxide to elemental nitrogen. The process is particularly suited to the removal of nitric oxide from flue gas streams and gas streams from nitric acid plants. Thiobacillus dentrificians as well as other bacteria are disclosed for use in the process.

  4. Inflatable containment diaphragm for sealing and removing stacks

    DOE Patents [OSTI]

    Meskanick, G.R.; Rosso, D.T.

    1993-04-13

    A diaphragm with an inflatable torus-shaped perimeter is used to seal at least one end of a stack so that debris that might be hazardous will not be released during removal of the stack. A diaphragm is inserted and inflated in the lower portion of a stack just above where the stack is to be cut such that the perimeter of the diaphragm expands and forms a seal against the interior surface of the stack.

  5. BOA II: pipe-asbestos insulation removal system

    SciTech Connect (OSTI)

    Schempf, H.; Mutschler; Boehmke, S.; Chemel, B.; Piepgras, C.

    1996-12-31

    BOA system is a mobile pipe-external robotic crawler used to remotely strip and bag asbestos-containing lagging and insulation materials from various diameter pipes in (primarily) industrial installations. Steam and process lines within the DOE weapons complex warrant the use of a remote device due to high labor costs and high level of radioactive contamination, making manual removal costly and inefficient. Currently targeted facilities for demonstration and remediation are Fernald in Ohio and Oak Ridge in Tennessee.

  6. System for the removal of contaminant soil-gas vapors

    DOE Patents [OSTI]

    Weidner, Jerry R. (Iona, ID); Downs, Wayne C. (Sugar City, ID); Kaser, Timothy G. (Ammon, ID); Hall, H. James (Idaho Falls, ID)

    1997-01-01

    A system extracts contaminated vapors from soil or other subsurface regions by using changes in barometric pressure to operate sensitive check valves that control air entry and removal from wells in the ground. The system creates an efficient subterranean flow of air through a contaminated soil plume and causes final extraction of the contaminants from the soil to ambient air above ground without any external energy sources.

  7. System for the removal of contaminant soil-gas vapors

    DOE Patents [OSTI]

    Weidner, J.R.; Downs, W.C.; Kaser, T.G.; Hall, H.J.

    1997-12-16

    A system extracts contaminated vapors from soil or other subsurface regions by using changes in barometric pressure to operate sensitive check valves that control air entry and removal from wells in the ground. The system creates an efficient subterranean flow of air through a contaminated soil plume and causes final extraction of the contaminants from the soil to ambient air above ground without any external energy sources. 4 figs.

  8. Nitrogen removal from natural gas using two types of membranes

    DOE Patents [OSTI]

    Baker, Richard W.; Lokhandwala, Kaaeid A.; Wijmans, Johannes G.; Da Costa, Andre R.

    2003-10-07

    A process for treating natural gas or other methane-rich gas to remove excess nitrogen. The invention relies on two-stage membrane separation, using methane-selective membranes for the first stage and nitrogen-selective membranes for the second stage. The process enables the nitrogen content of the gas to be substantially reduced, without requiring the membranes to be operated at very low temperatures.

  9. Fairer Trade, Removing Gender Bias in US Import Taxes 

    E-Print Network [OSTI]

    Taylor, Lori L.; Dar, Jawad

    2015-01-01

    Fairer Trade Removing Gender Bias in US Import Taxes LORI L. TAYLOR AND JAWAD DAR Mosbacher Institute VOLUME 6 | ISSUE 3 | 2015 There are many inequalities in US tariff policy. Products imported from certain countries enter duty free, while... in 2009 to honor Robert A. Mosbacher, Secretary of Commerce from 1989- 1992 and key architect of the North American Free Trade Agreement. Through our three core programs–Integration of Global Markets, Energy in a Global Economy, and Governance and Public...

  10. SPRU Removes High-Risk Radioactive Waste | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on DeliciousMathematicsEnergyInterestedReplacement-2-AA-1 SECTION J APPENDIXAllegations Related to theDoeSPRU Removes

  11. Ammonia removal process upgrade to the Acme Steel Coke Plant

    SciTech Connect (OSTI)

    Harris, J.L. [Acme Steel Co., Chicago, IL (United States). Chicago Coke Plant

    1995-12-01

    The need to upgrade the ammonia removal process at the Acme Steel Coke Plant developed with the installation of the benzene NESHAP (National Emission Standard for Hazardous Air Pollutants) equipment, specifically the replacement of the final cooler. At Acme Steel it was decided to replace the existing open cooling tower type final cooler with a closed loop direct spray tar/water final cooler. This new cooler has greatly reduced the emissions of benzene, ammonia, hydrogen sulfide and hydrogen cyanide to the atmosphere, bringing them into environmental compliance. At the time of its installation it was not fully recognized as to the effect this would have on the coke oven gas composition. In the late seventies the decision had been made at Acme Steel to stop the production of ammonia sulfate salt crystals. The direction chosen was to make a liquid ammonia sulfate solution. This product was used as a pickle liquor at first and then as a liquid fertilizer as more markets were developed. In the fall of 1986 the ammonia still was brought on line. The vapors generated from the operation of the stripping still are directed to the inlet of the ammonia absorber. At that point in time it was decided that an improvement to the cyclical ammonia removal process was needed. The improvements made were minimal yet allowed the circulation of solution through the ammonia absorber on a continuous basis. The paper describes the original batch process and the modifications made which allowed continuous removal.

  12. Pentek metal coating removal system: Baseline report; Summary

    SciTech Connect (OSTI)

    1997-07-31

    The Pentek metal coating removal system consists of the ROTO-PEEN Scaler, CORNER-CUTTER(R), and VAC-PAC(R). The system is designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M ROTO-PEEN tungsten carbide cutters, while the CORNER-CUTTER(R) uses solid needles for descaling activities. These are used with the VAC-PAC(R) vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure was minimal, but noise exposure was significant. Further testing for each exposure is recommended, since the outdoor environment where the testing demonstration took place may skew the results. It is feasible that dust and noise levels will be higher in an enclosed operating environment. Other areas of concern found were arm-hand vibration, whole-body vibration, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

  13. Sodium removal process development for LMFBR fuel subassemblies

    SciTech Connect (OSTI)

    Simmons, C.R.; Taylor, G.R.

    1981-10-01

    Two 37-pin scale models of Clinch River Breeder Reactor Plant fuel subassemblies were designed, fabricated and used at Westinghouse Advanced Reactors Division in the development and proof-testing of a rapid water-based sodium removal process for the ORNL Hot Experimental Facility, Liquid Metal Fast Breeder Reactor Fuel Reprocessing Cycle. Through a series of development tests on one of the models, including five (5) sodium wettings and three (3) high temperature sodium removal operations, optimum process parameters for a rapid water vapor-argon-water rinse process were identified and successfully proof-tested on a second model containing argon-pressurized, sodium-corroded model fuel pins simulating the gas plenum and cladding conditions expected for spent fuel pins in full scale subassemblies. Based on extrapolations of model proof test data, preliminary process parameters for a water vapor-nitrogen-water rinse process were calculated and recommended for use in processing full scale fuel subassemblies in the Sodium Removal Facility of the Fuel Receiving Cell, ORNL HEF.

  14. Process for removal of sulfur compounds from fuel gases

    DOE Patents [OSTI]

    Moore, Raymond H. (Richland, WA); Stegen, Gary E. (Richland, WA)

    1978-01-01

    Fuel gases such as those produced in the gasification of coal are stripped of sulfur compounds and particulate matter by contact with molten metal salt. The fuel gas and salt are intimately mixed by passage through a venturi or other constriction in which the fuel gas entrains the molten salt as dispersed droplets to a gas-liquid separator. The separated molten salt is divided into a major and a minor flow portion with the minor flow portion passing on to a regenerator in which it is contacted with steam and carbon dioxide as strip gas to remove sulfur compounds. The strip gas is further processed to recover sulfur. The depleted, minor flow portion of salt is passed again into contact with the fuel gas for further sulfur removal from the gas. The sulfur depleted, fuel gas then flows through a solid absorbent for removal of salt droplets. The minor flow portion of the molten salt is then recombined with the major flow portion for feed to the venturi.

  15. Acid rain control strategists overlook dust removal benefits

    SciTech Connect (OSTI)

    Not Available

    1989-09-01

    Various strategies for controlling acid rain by reducing SO{sub 2} from existing utilities have failed to take into account the incidental particulate removal abilities of SO{sub 2} scrubbers. This has resulted in over-estimating the costs of acid rain control by 25% or more. This oversight has also caused utilities to invest in preliminary engineering of precipitator upgrades which will never have to be made if scrubbers are installed. While it seems inexplicable that a factor of this importance could have been overlooked by the industry, it is because of the unique situation in old U.S. utility power plants. These plants have relatively inefficient particulate control equipment which is not subject to new source performance standards. New power plants incorporate highly efficient particulate control devices so the ability of the downstream scrubbers to remove dust is irrelevant. The very small amount of particulate entering the scrubber from a highly efficient precipitator could be offset by escaping sulfate particles from a poorly operated scrubber. So an informal guideline was established to indicate that the scrubber had no overall effect on particulate emissions. The industry has generalized upon this guideline when, in fact, it only applies to new plants. The McIlvaine Company in its FGD Knowledge Network has thoroughly documented evidence that SO{sub 2} scrubbers will remove as much as 95% of the particulate being emitted from the relatively low efficiency precipitators operating on the nations existing coal-fired power plants.

  16. BOA: Pipe-asbestos insulation removal robot system

    SciTech Connect (OSTI)

    Schempf, H.; Bares, J.; Mutschler, E. [and others

    1995-12-31

    This paper describes the BOA system, a mobile pipe-external crawler used to remotely strip and bag (possibly contaminated) asbestos-containing lagging and insulation materials (ACLIM) from various diameter pipes in (primarily) industrial installations across the DOE weapons complex. The mechanical removal of ACLIM is very cost-effective due to the relatively low productivity and high cost involved in human removal scenarios. BOA, a mechanical system capable of removing most forms of lagging (paper, plaster, aluminum sheet, clamps, screws and chicken-wire), and insulation (paper, tar, asbestos fiber, mag-block) uses a circular cutter and compression paddles to cut and strip the insulation off the pipe through compression, while a HEPA-filter and encapsulant system maintain a certifiable vacuum and moisture content inside the system and on the pipe, respectively. The crawler system has been built and is currently undergoing testing. Key design parameters and performance parameters are developed and used in performance testing. Since the current system is a testbed, we also discuss future enhancements and outline two deployment scenarios (robotic and manual) for the final system to be designed and completed by the end of FY `95. An on-site demonstration is currently planned for Fernald in Ohio and Oak Ridge in Tennessee.

  17. Process for the removal of impurities from combustion fullerenes

    DOE Patents [OSTI]

    Alford, J. Michael; Bolskar, Robert

    2005-08-02

    The invention generally relates to purification of carbon nanomaterials, particularly fullerenes, by removal of PAHs and other hydrocarbon impurities. The inventive process involves extracting a sample containing carbon nanomaterials with a solvent in which the PAHs are substantially soluble but in which the carbon nanomaterials are not substantially soluble. The sample can be repeatedly or continuously extracted with one or more solvents to remove a greater amount of impurities. Preferred solvents include ethanol, diethyl ether, and acetone. The invention also provides a process for efficiently separating solvent extractable fullerenes from samples containing fullerenes and PAHs wherein the sample is extracted with a solvent in which both fullerenes and PAHs are substantially soluble and the sample extract then undergoes selective extraction to remove PAHs. Suitable solvents in which both fullerenes and PAHs are soluble include o-xylene, toluene, and o-dichlorobenzene. The purification process is capable of treating quantities of combustion soot in excess of one kilogram and can produce fullerenes or fullerenic soot of suitable purity for many applications.

  18. Sulfur removal from diesel fuel-contaminated methanol.

    SciTech Connect (OSTI)

    Lee, S. H. D.; Kumar, R.; Krumpelt, M.; Chemical Engineering

    2002-03-01

    Methanol is considered to be a potential on-board fuel for fuel cell-powered vehicles. In current distribution systems for liquid fuels used in the transportation sector, commodity methanol can occasionally become contaminated with the sulfur in diesel fuel or gasoline. This sulfur would poison the catalytic materials used in fuel reformers for fuel cells. We tested the removal of this sulfur by means of ten activated carbons (AC) that are commercially available. Tests were conducted with methanol doped with 1 vol.% grade D-2 diesel fuel containing 0.29% sulfur, which was present essentially as 33-35 wt.% benzothiophenes (BTs) and 65-67 wt.% dibenzothiophenes (DBT). In general, coconut shell-based carbons activated by high-temperature steam were more effective at sulfur removal than coal-based carbons. Equilibrium sorption data showed linear increase in sulfur capture with the increase of sulfur concentration in methanol. Both types of carbons had similar breakthrough characteristics, with the dynamic sorption capacity of each being about one-third of its equilibrium sorption capacity. Results of this study suggest that a fixed-bed sorber of granular AC can be used, such as in refueling stations, for the removal of sulfur in diesel fuel-contaminated methanol.

  19. Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown Sites

    SciTech Connect (OSTI)

    Maheras, Steven J.; Best, Ralph E.; Ross, Steven B.; Buxton, Kenneth A.; England, Jeffery L.; McConnell, Paul E.

    2013-09-30

    This report fulfills the M2 milestone M2FT-13PN0912022, “Stranded Sites De-Inventorying Report.” In January 2013, the U.S. Department of Energy (DOE) issued the Strategy for the Management and Disposal of Used Nuclear Fuel and High-Level Radioactive Waste (DOE 2013). Among the elements contained in this strategy is an initial focus on accepting used nuclear fuel from shutdown reactor sites. This focus is consistent with the recommendations of the Blue Ribbon Commission on America’s Nuclear Future, which identified removal of stranded used nuclear fuel at shutdown sites as a priority so that these sites may be completely decommissioned and put to other beneficial uses (BRC 2012). Shutdown sites are defined as those commercial nuclear power reactor sites where the nuclear power reactors have been shut down and the site has been decommissioned or is undergoing decommissioning. In this report, a preliminary evaluation of removing used nuclear fuel from 12 shutdown sites was conducted. The shutdown sites were Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, Zion, Crystal River, Kewaunee, and San Onofre. These sites have no other operating nuclear power reactors at their sites and have also notified the U.S. Nuclear Regulatory Commission that their reactors have permanently ceased power operations and that nuclear fuel has been permanently removed from their reactor vessels. Shutdown reactors at sites having other operating reactors are not included in this evaluation.

  20. Process for off-gas particulate removal and apparatus therefor

    DOE Patents [OSTI]

    Carl, D.E.

    1997-10-21

    In the event of a breach in the off-gas line of a melter operation requiring closure of the line, a secondary vessel vent line is provided with a particulate collector utilizing atomization for removal of large particulates from the off-gas. The collector receives the gas containing particulates and directs a portion of the gas through outer and inner annular channels. The collector further receives a fluid, such as water, which is directed through the outer channel together with a second portion of the particulate-laden gas. The outer and inner channels have respective ring-like termination apertures concentrically disposed adjacent one another on the outer edge of the downstream side of the particulate collector. Each of the outer and inner channels curves outwardly away from the collector`s centerline in proceeding toward the downstream side of the collector. Gas flow in the outer channel maintains the fluid on the channel`s wall in the form of a ``wavy film,`` while the gas stream from the inner channel shears the fluid film as it exits the outer channel in reducing the fluid to small droplets. Droplets formed by the collector capture particulates in the gas stream by one of three mechanisms: impaction, interception or Brownian diffusion in removing the particulates. The particulate-laden droplets are removed from the fluid stream by a vessel vent condenser or mist eliminator. 4 figs.

  1. Process for off-gas particulate removal and apparatus therefor

    DOE Patents [OSTI]

    Carl, Daniel E. (Orchard Park, NY)

    1997-01-01

    In the event of a breach in the off-gas line of a melter operation requiring closure of the line, a secondary vessel vent line is provided with a particulate collector utilizing atomization for removal of large particulates from the off-gas. The collector receives the gas containing particulates and directs a portion of the gas through outer and inner annular channels. The collector further receives a fluid, such as water, which is directed through the outer channel together with a second portion of the particulate-laden gas. The outer and inner channels have respective ring-like termination apertures concentrically disposed adjacent one another on the outer edge of the downstream side of the particulate collector. Each of the outer and inner channels curves outwardly away from the collector's centerline in proceeding toward the downstream side of the collector. Gasflow in the outer channel maintains the fluid on the channel's wall in the form of a "wavy film," while the gas stream from the inner channel shears the fluid film as it exits the outer channel in reducing the fluid to small droplets. Droplets formed by the collector capture particulates in the gas stream by one of three mechanisms: impaction, interception or Brownian diffusion in removing the particulates. The particulate-laden droplets are removed from the fluid stream by a vessel vent condenser or mist eliminator.

  2. Method for removing oxide contamination from silicon carbide powders

    DOE Patents [OSTI]

    Brynestad, J.; Bamberger, C.E.

    1984-08-01

    The described invention is directed to a method for removing oxide contamination in the form of oxygen-containing compounds such as SiO/sub 2/ and B/sub 2/O/sub 3/ from a charge of finely divided silicon carbide. The silicon carbide charge is contacted with a stream of hydrogen fluoride mixed with an inert gas carrier such as argon at a temperature in the range of about 200/sup 0/ to 650/sup 0/C. The oxides in the charge react with the heated hydrogen fluoride to form volatile gaseous fluorides such as SiF/sub 4/ and BF/sub 3/ which pass through the charge along with unreacted hydrogen fluoride and the carrier gas. Any residual gaseous reaction products and hydrogen fluoride remaining in the charge are removed by contacting the charge with the stream of inert gas which also cools the powder to room temperature. The removal of the oxygen contamination by practicing the present method provides silicon carbide powders with desirable pressing and sintering characteristics. 1 tab.

  3. 1,153-ton Waste Vault Removed from 300 Area - Vault held waste...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1,153-ton Waste Vault Removed from 300 Area - Vault held waste tanks with contamination from Hanford's former laboratory facilities 1,153-ton Waste Vault Removed from 300 Area -...

  4. Removal of Chloride from Wastewater by Advanced Softening Process Using Electrochemically Generated Aluminum Hydroxide 

    E-Print Network [OSTI]

    Mustafa, Syed Faisal

    2014-07-23

    solubility. Chloride can be removed from water and wastewater by precipitation as calcium chloroaluminate using advanced softening process. This research was conducted to evaluate chloride removal using electrochemically generated aluminum hydroxide and lime...

  5. Java support on genepool: java6 (jdk1.6) will be removed on 08...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Java support on genepool: java6 (jdk1.6) will be removed on 08302013; firefox security updates Java support on genepool: java6 (jdk1.6) will be removed on 08302013; firefox...

  6. Department of Energy to Take Steps to Remove ENERGY STAR Label...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    to Take Steps to Remove ENERGY STAR Label on Certain LG Refrigerator-Freezer Models Department of Energy to Take Steps to Remove ENERGY STAR Label on Certain LG...

  7. Chemical Addition prior to Membrane Processes for Natural Organic Matter (NOM) Removal 

    E-Print Network [OSTI]

    Schäfer, Andrea; Fane, Anthony G.; Waite, T. D.

    1998-01-01

    Membrane processes for surface water treatment include microfiltration (MF), ultrafiltration (UF) and nanofiltration (NF), depending on the target material to be removed and the limiting process economics. MF will remove ...

  8. Channel adjustments following two dam removals in Wisconsin Martin W. Doyle

    E-Print Network [OSTI]

    Stanley, Emily

    the removal of low-head dams on two low- gradient, fine- to coarse-grained rivers in southern Wisconsin

  9. Coupled effects of flow field geometry and diffusion media material structure on evaporative water removal from

    E-Print Network [OSTI]

    Mench, Matthew M.

    (PEFC) is responsible for many degradation and durability issues [1e4]. To remove water from the stack

  10. SULFURIC ACID REMOVAL PROCESS EVALUATION: LONG-TERM RESULTS

    SciTech Connect (OSTI)

    Gary M. Blythe; Richard McMillan

    2002-07-03

    The objective of this project is to demonstrate the use of alkaline reagents injected into the furnace of coal-fired boilers as a means of controlling sulfuric acid emissions. The project is being co-funded by the U.S. DOE National Energy Technology Laboratory, under Cooperative Agreement DE-FC26-99FT40718, along with EPRI, the American Electric Power Company (AEP), FirstEnergy Corp., the Tennessee Valley Authority, and Dravo Lime, Inc. Sulfuric acid controls are becoming of increasing interest to power generators with coal-fired units for a number of reasons. Sulfuric acid is a Toxic Release Inventory species and can cause a variety of plant operation problems such as air heater plugging and fouling, back-end corrosion, and plume opacity. These issues will likely be exacerbated with the retrofit of selective catalytic reduction (SCR) for NO{sub x} control on many coal-fired plants, as SCR catalysts are known to further oxidize a portion of the flue gas SO{sub 2} to SO{sub 3}. The project previously tested the effectiveness of furnace injection of four different calcium-and/or magnesium-based alkaline sorbents on full-scale utility boilers. These reagents were tested during four one- to two-week tests conducted on two FirstEnergy Bruce Mansfield Plant (BMP) units. One of the sorbents tested was a magnesium hydroxide byproduct slurry produced from a modified Thiosorbic{reg_sign} Lime wet flue gas desulfurization system. The other three sorbents are available commercially and include dolomite, pressure-hydrated dolomitic lime, and commercial magnesium hydroxide. The dolomite reagent was injected as a dry powder through out-of-service burners, while the other three reagents were injected as slurries through air-atomizing nozzles inserted through the front wall of the upper furnace, either across from the nose of the furnace or across from the pendant superheater tubes. After completing the four one- to two-week tests, the most promising sorbents were selected for longer-term (approximately 25-day) full-scale tests on two different units. The longer-term tests were conducted to confirm the effectiveness of the sorbents tested over extended operation on two different boilers, and to determine balance-of-plant impacts. The first long-term test was conducted on FirstEnergy's BMP, Unit 3, and the second test was conducted on AEP's Gavin Plant, Unit 1. The Gavin Plant testing provided an opportunity to evaluate the effects of sorbent injected into the furnace on SO{sub 3} formed across an operating SCR reactor. This report presents the results from those long-term tests. The tests determined the effectiveness of injecting commercially available magnesium hydroxide slurry (Gavin Plant) and byproduct magnesium hydroxide slurry (both Gavin Plant and BMP) for sulfuric acid control. The results show that injecting either slurry could achieve up to 70 to 75% overall sulfuric acid removal. At BMP, this overall removal was limited by the need to maintain acceptable electrostatic precipitator (ESP) particulate control performance. At Gavin Plant, the overall sulfuric acid removal was limited because the furnace injected sorbent was less effective at removing SO{sub 3} formed across the SCR system installed on the unit for NOX control than at removing SO{sub 3} formed in the furnace. The long-term tests also determined balance-of-plant impacts from slurry injection during the two tests. These include impacts on boiler back-end temperatures and pressure drops, SCR catalyst properties, ESP performance, removal of other flue gas species, and flue gas opacity. For the most part the balance-of-plant impacts were neutral to positive, although adverse effects on ESP performance became an issue during the BMP test.

  11. Dynamics of pebbles in the vicinity of a growing planetary embryo: hydro-dynamical simulations

    E-Print Network [OSTI]

    Morbidelli, Alessandro

    2012-01-01

    Understanding the growth of the cores of giant planets is a difficult problem. Recently, Lambrechts and Johansen (2012; LJ12) proposed a new model in which the cores grow by the accretion of pebble-size objects, as the latter drift towards the star due to gas drag. Here, we investigate the dynamics of pebble-size objects in the vicinity of planetary embryos of 1 and 5 Earth masses and the resulting accretion rates. We use hydrodynamical simulations, in which the embryo influences the dynamics of the gas and the pebbles suffer gas drag according to the local gas density and velocities. The pebble dynamics in the vicinity of the planetary embryo is non-trivial, and it changes significantly with the pebble size. Nevertheless, the accretion rate of the embryo that we measure is within an order of magnitude of the rate estimated in LJ12 and tends to their value with increasing pebble-size. We conclude that the model by LJ12 has the potential to explain the rapid growth of giant planet cores. The actual accretion r...

  12. Results from intercropping fast-growing trees and food crops at Morogoro, Tanzania

    SciTech Connect (OSTI)

    Redhead, J.F.

    1992-12-31

    In Morogoro, Tanzania, agroforestry trials were set up to investigate intercropping with primarily eucalypt species. The climate in the region is very similar to Kolar, Karnataka State, India. Three crops-sorghum, bean and maize-were grown annually under Eucalyptus tereticornis at 2.5 m x 2.5 m for three years with a range of weeding practices. Plots that were intercropped with beans showed best results. Shading by the eucalypts after three years resulted in negligible crop yields in all treatments. Three tree spacings of E. camaldulensis (3 m x 3 m, 4 m x 4 m, and 5 m x 5 m) were combined with the intercropping of beans and maize. Beans gave satisfactory yields at all spacings, but the maize showed significantly depressed yields at 3 m x 3 m at 4 m x 4 m, but was similar to pure maize crop at 5 m x 5 m spacing. Overall the extra revenue from a food crop in the first and second year of tree growth increases the return from the land. The short rotation of fast growing trees depleted the soil of nutrients and, as with other crops, the fertility would have to be maintained by applying fertilizer.

  13. Oil demand continues to grow in the U.S. and worldwide

    SciTech Connect (OSTI)

    Tippee, B.; Beck, R.J.

    1995-07-31

    Rising oil consumption is challenging the Organization of Petroleum Exporting Countries production quota--but not the group`s ability to meet demand. In the second half of 1995, the oil market will continue to need more oil from OPEC members than the group claims to be willing to produce with its quota at 24.52 million b/d. If the quota really limited supply, ingredients would be in place for a significant price hike. Growth in a non-OPEC production intensities temptations on OPEC members to cheat on quotas and has become a key factor in the market. OPEC producers have seen that if they don`t meet incremental demand at the current price, other producers will. OPEC eventually will have to raise its quota or acknowledge that the artificial production limit lacks meaning. At present, the only real limit to supply is production capacity, which remains in excess relative to demand and which has demonstrated its ability to grow both within and outside of OPEC when prices rise. The paper discusses worldwide trends, pressures on OPEC, world crude prices, US prices, natural gas prices, US energy demand, natural gas use, gas supply, US demand for petroleum products, imports, and inventories.

  14. Growing White Dwarfs to the Chandrasekhar Limit: The Parameter Space of the Single Degenerate SNIa Channel

    E-Print Network [OSTI]

    Hillman, Yael; Kovetz, Attay; Shara, Michael M

    2015-01-01

    Can a white dwarf, accreting hydrogen-rich matter from a non-degenerate companion star, ever exceed the Chandrasekhar mass and explode as a type Ia supernova? We explore the range of accretion rates that allow a white dwarf (WD) to secularly grow in mass, and derive limits on the accretion rate and on the initial mass that will allow it to reach $1.4M_\\odot$ --- the Chandrasekhar mass. We follow the evolution through a long series of hydrogen flashes, during which a thick helium shell accumulates. This determines the effective helium mass accretion rate for long-term, self-consistent evolutionary runs with helium flashes. We find that net mass accumulation always occurs despite helium flashes. Although the amount of mass lost during the first few helium shell flashes is a significant fraction of that accumulated prior to the flash, that fraction decreases with repeated helium shell flashes. Eventually no mass is ejected at all during subsequent flashes. This unexpected result occurs because of continual heati...

  15. As dam removal continues to grow as a viable option for river management, questions pertaining to the influence of reservoir sediment on a river channel downstream must be addressed. This study evaluated

    E-Print Network [OSTI]

    Curran, Joanna C.

    , but their contributions have not yet been determined. References Curran, Joanna C. and P. R. Wilcock. 2005. Effect of sand. Curran Department of Geography, Texas State University-San Marcos Poster Number H51G-0587 Original sand armors and not when sand is added. * for sand and gravel fractions are compared to data from Curran

  16. BOA: Asbestos pipe insulation removal robot system. Phase 1

    SciTech Connect (OSTI)

    Schempf, H.; Bares, J.E.

    1995-02-01

    The project described in this report targets the development of a mechanized system for safe, cost-efficient and automated abatement of asbestos containing materials used as pipe insulation. Based on several key design criteria and site visits, a proof-of-concept prototype robot system, dubbed BOA, was designed and built, which automatically strips the lagging and insulation from the pipes, and encapsulates them under complete vacuum operation. The system can operate on straight runs of piping in horizontal or vertical orientations. Currently we are limited to four-inch diameter piping without obstacles as well as a somewhat laborious emplacement and removal procedure -- restrictions to be alleviated through continued development. BOA removed asbestos at a rate of 4-5 ft./h compared to 3 ft./h for manual removal of asbestos with a 3-person crew. The containment and vacuum system on BOA was able to achieve the regulatory requirement for airborne fiber emissions of 0.01 fibers/ccm/ 8-hr. shift. This program consists of two phases. The first phase was completed and a demonstration was given to a review panel, consisting of DOE headquarters and site representatives as well as commercial abatement industry representatives. Based on the technical and programmatic recommendations drafted, presented and discussed during the review meeting, a new plan for the Phase II effort of this project was developed. Phase 11 will consist of a 26-month effort, with an up-front 4-month site-, market-, cost/benefit and regulatory study before the next BOA robot (14 months) is built, and then deployed and demonstrated (3 months) at a DOE site (such as Fernald or Oak Ridge) by the beginning of FY`97.

  17. Flattening filter removal for improved image quality of megavoltage fluoroscopy

    SciTech Connect (OSTI)

    Christensen, James D.; Kirichenko, Alexander; Gayou, Olivier

    2013-08-15

    Purpose: Removal of the linear accelerator (linac) flattening filter enables a high rate of dose deposition with reduced treatment time. When used for megavoltage imaging, an unflat beam has reduced primary beam scatter resulting in sharper images. In fluoroscopic imaging mode, the unflat beam has higher photon count per image frame yielding higher contrast-to-noise ratio. The authors’ goal was to quantify the effects of an unflat beam on the image quality of megavoltage portal and fluoroscopic images.Methods: 6 MV projection images were acquired in fluoroscopic and portal modes using an electronic flat-panel imager. The effects of the flattening filter on the relative modulation transfer function (MTF) and contrast-to-noise ratio were quantified using the QC3 phantom. The impact of FF removal on the contrast-to-noise ratio of gold fiducial markers also was studied under various scatter conditions.Results: The unflat beam had improved contrast resolution, up to 40% increase in MTF contrast at the highest frequency measured (0.75 line pairs/mm). The contrast-to-noise ratio was increased as expected from the increased photon flux. The visualization of fiducial markers was markedly better using the unflat beam under all scatter conditions, enabling visualization of thin gold fiducial markers, the thinnest of which was not visible using the unflat beam.Conclusions: The removal of the flattening filter from a clinical linac leads to quantifiable improvements in the image quality of megavoltage projection images. These gains enable observers to more easily visualize thin fiducial markers and track their motion on fluoroscopic images.

  18. Nitrate removal from irrigation run-off using packed-bed bioreactors 

    E-Print Network [OSTI]

    Abrameit, Bradley Kyle

    1996-01-01

    of the columns with the majority (21.12%) being removed in the final region. Intermediate regions reduced 5.2-16.5%. Ammonium concentrations remained steady with slight removal (6.3-1 1. I%) occurring in the first two regions. Efficiency of N03- and N02-removal...

  19. Efficient salt removal in a continuously operated upflow microbial desalination cell with an air cathode

    E-Print Network [OSTI]

    Efficient salt removal in a continuously operated upflow microbial desalination cell with an air of salt removal. During the 4-month operation, the UMDC constantly removed salts and generated bio-electricity. At a hydraulic retention time (HRT) of 4 days (salt solution) and current production of $62 mA, the UMDC was able

  20. Salt-and-Pepper Noise Removal by Median-type Noise Detectors and

    E-Print Network [OSTI]

    Chan, Raymond

    1 Salt-and-Pepper Noise Removal by Median-type Noise Detectors and Detail-preserving Regularization for removing salt-and-pepper impulse noise. In the first phase, an adaptive median filter is used to identify remove salt-and-pepper-noise with noise level as high as 90%. Index Terms Impulse noise, adaptive median

  1. Virus removal by soil passage at field scale and ground-water protection of sandy aquifers

    E-Print Network [OSTI]

    Hassanizadeh, S. Majid

    Virus removal by soil passage at field scale and ground- water protection of sandy aquifers J; The Netherlands (E-mail: Majid@ct.tudelft.nl) Abstract Virus removal from groundwater by soil passage often for attachment than thereafter. A model is presented which interprets virus removal as a function of collision

  2. Removal of floating organic in Hanford Waste Tank 241-C-103 restart plan

    SciTech Connect (OSTI)

    Wilson, T.R.; Hanson, C.

    1994-10-03

    The decision whether or not to remove the organic layer from Waste Tank 241-C-103 was deferred until May, 1995. The following restart plan was prepared for removal of the organic if the decision is to remove the organic from the waste tank 241-C-103.

  3. Does Small Dam Removal Affect Local Property Values? An Empirical Analysis Bill Provencher

    E-Print Network [OSTI]

    Provencher, R. William

    Does Small Dam Removal Affect Local Property Values? An Empirical Analysis Bill Provencher of small dam removal on property values in south-central Wisconsin. Data on residential property sales were obtained for three categories of sites: those where a dam is intact, those where a dam was recently removed

  4. Total nitrogen removal in a hybrid, membrane-aerated activated sludge process

    E-Print Network [OSTI]

    Nerenberg, Robert

    Total nitrogen removal in a hybrid, membrane-aerated activated sludge process Leon S. Downing wastewater. Air-filled hollow-fiber membranes are incorporated into an activated sludge tank removal in activated sludge. ª 2008 Elsevier Ltd. All rights reserved. 1. Introduction The removal

  5. Widget:RemovePDFImageDimensions | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page| Open Energy Information Serbia-EnhancingEtGeorgia: EnergyMaryland:Meadow Lake,Maine:RemovePDFImageDimensions Jump to:

  6. A solvent system to provide selective removal of sulfur compounds

    SciTech Connect (OSTI)

    Pearce, R.L.; Bacon, T.R.

    1986-01-01

    Energy costs and SRU inefficiencies resulting from utilization of low strength MEA technology induced a large refinery to convert to MDEA. One of the seven product streams being treated required extremely low carbonyl sulfide in the treated product. This required careful consideration in making the decision to convert. However, the conclusions were that the advantages outweighed the disadvantages. When the initial converted operations verified a need to improve the carbonyl sulfide removal, GAS/SPEC Tech Service produced an innovative solution which allowed for efficient operation at acceptable COS specification, lower energy utilization, reduced solvent losses, and improved sulfur recovery unit operation.

  7. Process for removing carbonyl sulfide from gaseous streams

    SciTech Connect (OSTI)

    Tellis, C.

    1981-11-10

    This invention relates to a process for reducing the carbonyl sulfide content of a gaseous stream which has a concentration of carbonyl sulfide of from at least 1 to about 100 parts per million, by volume, which comprises providing an absorbent bed wherein the absorbent comprises zinc oxide and contains no more than 5%, by weight, of an oxide of an alkli or alkaline earth metal, and contacting said process stream with said adsorbent bed at a temperature of from about ambient to 250/sup 0/ C. For a period of time sufficient to remove at least 90% of the carbonyl sulfide content of said gaseous stream.

  8. Reactor Vessel Removal: Improving Performance Big Rock Point Lessons Learned

    SciTech Connect (OSTI)

    Daly, P.T. [BNG America, D and D Operations, 804 South Illinois Avenue, Oak Ridge, TN 37830 (United States)

    2006-07-01

    The Big Rock Point (BRP) reactor vessel was successfully removed, packaged in a Type B shipping container, transported, and buried. The process took almost 4 years of work by many people and a variety of companies. This paper will discuss several areas that can reduce schedule time, resulting in reduced cost and employee dose exposure. For maximum cost effectiveness, these lessons should be applied during the planning stages when developing baseline cost and schedule, As Low As Reasonably Achievable (ALARA) budgets, and work processes. (authors)

  9. Feed gas contaminant removal in ion transport membrane systems

    DOE Patents [OSTI]

    Underwood, Richard Paul (Allentown, PA); Makitka, III, Alexander (Hatfield, PA); Carolan, Michael Francis (Allentown, PA)

    2012-04-03

    An oxygen ion transport membrane process wherein a heated oxygen-containing gas having one or more contaminants is contacted with a reactive solid material to remove the one or more contaminants. The reactive solid material is provided as a deposit on a support. The one or more contaminant compounds in the heated oxygen-containing gas react with the reactive solid material. The contaminant-depleted oxygen-containing gas is contacted with a membrane, and oxygen is transported through the membrane to provide transported oxygen.

  10. System and method for removal of buried objects

    DOE Patents [OSTI]

    Alexander, Robert G. (Richland, WA); Crass, Dennis (Kennewick, WA); Grams, William (Kennewick, WA); Phillips, Steven J. (Sunnyside, WA); Riess, Mark (Kennewick, WA)

    2008-06-03

    The present invention is a system and method for removal of buried objects. According to one embodiment of the invention, a crane with a vibrator casing driver is used to lift and suspend a large diameter steel casing over the buried object. Then the casing is driven into the ground by the vibratory driver until the casing surrounds the buried object. Then the open bottom of the casing is sealed shut by injecting grout into the ground within the casing near its bottom. When the seal has cured and hardened, the top of the casing is lifted to retrieve the casing, with the buried object inside, from the ground.

  11. Analytical methods for removing radiological constituents prior to organic analysis

    SciTech Connect (OSTI)

    Hakonson, K.; Monagle, M.; Cournoyer, M.

    1997-12-31

    Within the Department of Energy (DOE), there is a need to analyze mixed waste materials (i.e. materials that are contaminated with both radiological and hazardous components). As part of the technical support the Organic Analysis Group provides for programs within Los Alamos National Laboratory, methods are under development for radiologically contaminated oil samples being tested for polychlorinated biphenyls and other semivolatile constituents. Radionuclides are removed from oil samples by filtering the samples through a commercials available solid phase extraction cartridge. An aliquot of the eluent is then analyzed to quantitate the residual radioactivity.

  12. Process for removal of hazardous air pollutants from coal

    DOE Patents [OSTI]

    Akers, David J. (Indiana, PA); Ekechukwu, Kenneth N. (Silver Spring, MD); Aluko, Mobolaji E. (Burtonsville, MD); Lebowitz, Howard E. (Mountain View, CA)

    2000-01-01

    An improved process for removing mercury and other trace elements from coal containing pyrite by forming a slurry of finely divided coal in a liquid solvent capable of forming ions or radicals having a tendency to react with constituents of pyrite or to attack the bond between pyrite and coal and/or to react with mercury to form mercury vapors, and heating the slurry in a closed container to a temperature of at least about 50.degree. C. to produce vapors of the solvent and withdrawing vapors including solvent and mercury-containing vapors from the closed container, then separating mercury from the vapors withdrawn.

  13. Method for removing cesium from a nuclear reactor coolant

    DOE Patents [OSTI]

    Colburn, Richard P. (Pasco, WA)

    1986-01-01

    A method of and system for removing cesium from a liquid metal reactor coolant including a carbon packing trap in the primary coolant system for absorbing a major portion of the radioactive cesium from the coolant flowing therethrough at a reduced temperature. A regeneration subloop system having a secondary carbon packing trap is selectively connected to the primary system for isolating the main trap therefrom and connecting it to the regeneration system. Increasing the temperature of the sodium flowing through the primary trap diffuses a portion of the cesium

  14. System for fuel rod removal from a reactor module

    DOE Patents [OSTI]

    Matchett, Richard L. (Bethel Park, PA); Roof, David R. (North Huntingdon, PA); Kikta, Thomas J. (Pittsburgh, PA); Wilczynski, Rosemarie (McKees Rocks, PA); Nilsen, Roy J. (Pittsburgh, PA); Bacvinskas, William S. (Bethel Park, PA); Fodor, George (Pittsburgh, PA)

    1990-01-01

    A robotic system for remote underwater withdrawal of the fuel rods from fuel modules of a light water breeder reactor includes a collet/grapple assembly for gripping and removing fuel rods in each module, which is positioned by use of a winch and a radial support means attached to a vertical support tube which is mounted over the fuel module. A programmable logic controller in conjunction with a microcomputer, provides control for the accurate positioning and pulling force of the rod grapple assembly. Closed circuit television cameras are provided which aid in operator interface with the robotic system.

  15. Method of removing and detoxifying a phosphorus-based substance

    DOE Patents [OSTI]

    Vandegrift, G.F.; Steindler, M.J.

    1985-05-21

    A method of removing a phosphorus-based poisonous substance from water contaminated is presented. In addition, the toxicity of the phosphorus-based substance is also subsequently destroyed. A water-immiscible organic solvent is first immobilized on a supported liquid membrane before the contaminated water is contacted with one side of the supported liquid membrane to absorb the phosphorus-based substance in the organic solvent. The other side of the supported liquid membrane is contacted with a hydroxy-affording strong base to react with phosphorus-based solvated species to form a non-toxic product.

  16. Method of dye removal for the textile industry

    DOE Patents [OSTI]

    Stone, Mark L. (Idaho Falls, ID)

    2000-01-01

    The invention comprises a method of processing a waste stream containing dyes, such as a dye bath used in the textile industry. The invention comprises using an inorganic-based polymer, such as polyphosphazene, to separate dyes and/or other chemicals from the waste stream. Membranes comprising polyphosphazene have the chemical and thermal stability to survive the harsh, high temperature environment of dye waste streams, and have been shown to completely separate dyes from the waste stream. Several polyphosplhazene membranes having a variety of organic substituent have been shown effective in removing color from waste streams.

  17. Butyl acetate replaces toluene to remove phenol from water

    SciTech Connect (OSTI)

    Hodel, A.E.

    1993-03-01

    Plastics Engineering Co. manufactures phenol formaldehyde resins and molding compounds at a plant in Sheboygan, WI. Process water from the plant, containing 7% phenol and 1% methanol, requires treatment prior to discharge to the sewer. Toluene was used as a solvent in a countercurrent liquid-liquid extraction column. A vacuum distillation of the extract separated the phenol and toluene. The raffinate (1% methanol, 98% water and 1% toluene) was stripped to recover the toluene and remove methanol from the bottoms prior to discharge. Methanol was not recovered. Disposal costs for the waste methanol (with about 10% toluene as an azeotrope) were high.

  18. Removal of sulfur and nitrogen containing pollutants from discharge gases

    DOE Patents [OSTI]

    Joubert, James I. (Pittsburgh, PA)

    1986-01-01

    Oxides of sulfur and of nitrogen are removed from waste gases by reaction with an unsupported copper oxide powder to form copper sulfate. The resulting copper sulfate is dissolved in water to effect separation from insoluble mineral ash and dried to form solid copper sulfate pentahydrate. This solid sulfate is thermally decomposed to finely divided copper oxide powder with high specific surface area. The copper oxide powder is recycled into contact with the waste gases requiring cleanup. A reducing gas can be introduced to convert the oxide of nitrogen pollutants to nitrogen.

  19. Process for removing an organic compound from water

    DOE Patents [OSTI]

    Baker, Richard W. (Palo Alto, CA); Kaschemekat, Jurgen (Palo Alto, CA); Wijmans, Johannes G. (Menlo Park, CA); Kamaruddin, Henky D. (San Francisco, CA)

    1993-12-28

    A process for removing organic compounds from water is disclosed. The process involves gas stripping followed by membrane separation treatment of the stripping gas. The stripping step can be carried out using one or multiple gas strippers and using air or any other gas as stripping gas. The membrane separation step can be carried out using a single-stage membrane unit or a multistage unit. Apparatus for carrying out the process is also disclosed. The process is particularly suited for treatment of contaminated groundwater or industrial wastewater.

  20. System for fuel rod removal from a reactor module

    DOE Patents [OSTI]

    Matchett, R.L.; Fodor, G.; Kikta, T.J.; Bacvinsicas, W.S.; Roof, D.R.; Nilsen, R.J.; Wilczynski, R.

    1988-07-28

    A robotic system for remote underwater withdrawal of the fuel rods from fuel modules of a light water breeder reactor includes a collet/grapple assembly for gripping and removing fuel rods in each module, which is positioned by use of a winch and a radial support means attached to a vertical support tube which is mounted over the fuel module. A programmable logic controller in conjunction with a microcomputer, provides control for the accurate positioning and pulling force of the rod grapple assembly. Closed circuit television cameras are provided which aid in operator interface with the robotic system. 7 figs.

  1. Method for removing organic liquids from aqueous solutions and mixtures

    DOE Patents [OSTI]

    Hrubesh, Lawrence W.; Coronado, Paul R.; Dow, Jerome P.

    2004-03-23

    A method for removing organic liquids from aqueous solutions and mixtures. The method employs any porous material preferably in granular form and having small pores and a large specific surface area, that is hydrophobic so that liquid water does not readily wet its surface. In this method, organics, especially organic solvents that mix with and are more volatile than water, are separated from aqueous solution by preferentially evaporating across the liquid/solid boundary formed at the surfaces of the hydrophobic porous materials. Also, organic solvents that are immiscible with water, preferentially wet the surfaces of the hydrophobic material and are drawn within the porous materials by capillary action.

  2. Extraction process for removing metallic impurities from alkalide metals

    DOE Patents [OSTI]

    Royer, L.T.

    1987-03-20

    A development is described for removing metallic impurities from alkali metals by employing an extraction process wherein the metallic impurities are extracted from a molten alkali metal into molten lithium metal due to the immiscibility of the alkali metals in lithium and the miscibility of the metallic contaminants or impurities in the lithium. The purified alkali metal may be readily separated from the contaminant-containing lithium metal by simple decanting due to the differences in densities and melting temperatures of the alkali metals as compared to lithium.

  3. Apparatus for removal of particulate matter from gas streams

    DOE Patents [OSTI]

    Smith, Peyton L. (Baton Rouge, LA); Morse, John C. (Baton Rouge, LA)

    2000-01-01

    An apparatus for the removal of particulate matter from the gaseous product stream of an entrained flow coal gasifier which apparatus includes an initial screen, an intermediate screen which is aligned with the direction of flow of the gaseous product stream and a final screen transversely disposed to the flow of gaseous product and which apparatus is capable of withstanding at least a pressure differential of about 10 psi (68.95 kPa) or greater at the temperatures of the gaseous product stream.

  4. High SO{sub 2} removal efficiency testing

    SciTech Connect (OSTI)

    NONE

    1995-03-10

    Tests were conducted on the Tampa Electric Company`s (TECo) Big Bend Station, Unit 4 flue gas desulfurization (FGD) system to evaluate an option for achieving high sulfur dioxide (SO{sub 2}) removal efficiencies. The option tested was the addition of dibasic acid (DBA) additive. In addition, the effectiveness of other potential options was simulated with the Electric Power Research Institute`s (EPRI) FGD PRocess Integration and Simulation Model (FGDPRISM) after it was calibrated to the system. An economic analysis was conducted to determine the cost effectiveness of each option considered.

  5. Removing nuclear waste, one shipment at a time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMassR&D100 Winners *ReindustrializationEnergy RemoteNanostructures - EnergyRemoving

  6. Install Removable Insulation on Valves and Fittings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergyTher i nA Guide toIMPROVEMENT OFBarriers toDepartment13571installing removable

  7. WCH Removes Massive Test Reactor | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust,Field-effectWorking WithTelecentricN A 035(92/02) nerg *4 o** 0, WF* W A ,WATCHWCH Removes

  8. Example Cleanup: Removal of Polychlorinated Biphenyls from Hillside 140

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would like submitKansasCommunitiesof Energy8) Wigner HomeExample Cleanup Removal of

  9. Alternative cooling resource for removing the residual heat of reactor

    SciTech Connect (OSTI)

    Park, H. C.; Lee, J. H.; Lee, D. S.; Jung, C. Y.; Choi, K. Y. [Korea Hydro and Nuclear Power Co., Ltd., 260 Naa-ri Yangnam-myeon Gyeongju-si, Gyeonasangbuk-do, 780-815 (Korea, Republic of)

    2012-07-01

    The Recirculated Cooling Water (RCW) system of a Candu reactor is a closed cooling system which delivers demineralized water to coolers and components in the Service Building, the Reactor Building, and the Turbine Building and the recirculated cooling water is designed to be cooled by the Raw Service Water (RSW). During the period of scheduled outage, the RCW system provides cooling water to the heat exchangers of the Shutdown Cooling System (SDCS) in order to remove the residual heat of the reactor, so the RCW heat exchangers have to operate at all times. This makes it very hard to replace the inlet and outlet valves of the RCW heat exchangers because the replacement work requires the isolation of the RCW. A task force was formed to prepare a plan to substitute the recirculated water with the chilled water system in order to cool the SDCS heat exchangers. A verification test conducted in 2007 proved that alternative cooling was possible for the removal of the residual heat of the reactor and in 2008 the replacement of inlet and outlet valves of the RCW heat exchangers for both Wolsong unit 3 and 4 were successfully completed. (authors)

  10. Method and apparatus for removing ions from soil

    DOE Patents [OSTI]

    Bibler, Jane P. (813 E. Rollingwood Rd., Aiken, SC 29801)

    1993-01-01

    A method and apparatus for selectively removing species of ions from an area of soil. Permeable membranes 14 and 18 impregnated with an ion exchange resin that is specific to one or more species of chemical ions are inserted into ground 12 in close proximity to, and on opposing sides of, a soil area of interest 22. An electric potential is applied across electrodes 26 and 28 to cause the migration of ions out of soil area 22 toward the membranes 14 and 18. Preferably, the resin exchanges ions of sodium or hydrogen for ions of mercury that it captures from soil area 22. Once membranes 14 and 18 become substantially saturated with mercury ions, the potential applied across electrodes 26 and 28 is discontinued and membranes 14 and 18 are preferably removed from soil 12 for storage or recovery of the ions. The membranes are also preferably impregnated with a buffer to inhibit the effect of the hydrolysis of water by current from the electrodes.

  11. Method and apparatus for removing ions from soil

    DOE Patents [OSTI]

    Bibler, J.P.

    1993-03-02

    A method and apparatus are presented for selectively removing species of ions from an area of soil. Permeable membranes 14 and 18 impregnated with an ion exchange resin that is specific to one or more species of chemical ions are inserted into ground 12 in close proximity to, and on opposing sides of, a soil area of interest 22. An electric potential is applied across electrodes 26 and 28 to cause the migration of ions out of soil area 22 toward the membranes 14 and 18. Preferably, the resin exchanges ions of sodium or hydrogen for ions of mercury that it captures from soil area 22. Once membranes 14 and 18 become substantially saturated with mercury ions, the potential applied across electrodes 26 and 28 is discontinued and membranes 14 and 18 are preferably removed from soil 12 for storage or recovery of the ions. The membranes are also preferably impregnated with a buffer to inhibit the effect of the hydrolysis of water by current from the electrodes.

  12. High SO[sub 2] removal efficiency testing

    SciTech Connect (OSTI)

    Blythe, G.

    1993-04-22

    This document provides a discussion of the technical progress on DOE-PETC Project Number AC22-92PC91338, High Efficiency SO[sub 2] Removal Testing,'' for the time period from January 1 through March 31, 1993. The project involves testing at full-scale utility flue gas desulfurization (FGD) systems to evaluate low capital cost upgrades that may allow these systems to achieve up to 98% SO[sub 2] removal efficiency. The options to be evaluated primarily involve the addition of organic acid buffers to the FGD systems. The base'' project involves testing at one site, Tampa Electric Company's Big Bend Station. Up to five optional sites may be added to the program at the discretion of DOE-PETC. By March 31, 1993, four of those five options had been exercised. The options include testing at Hoosier Energy's Merom Station (Option I), Southwestern Electric Power Company's (SWEPCo) Pirkey Station (Option II), PSI Energy's Gibson Station (Option III), and Duquesne Light's Elrama Station (Option IV). The remainder of this document is divided into three sections. Section 2, Project Summary, provides a brief overview of the technical efforts on this project during the quarter. Section 3, Results, summarizes the outcome of those technical efforts. Results for the Base Program and for Options I and II are discussed in separate subsections. There are no technical results yet for Options III and IV, which were just exercised by DOE-PETC this quarter.

  13. Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown Sites

    SciTech Connect (OSTI)

    Maheras, Steven J.; Best, Ralph E.; Ross, Steven B.; Buxton, Kenneth A.; England, Jeffery L.; McConnell, Paul E.; Massaro, Lawrence M.; Jensen, Philip J.

    2014-10-01

    This report presents a preliminary evaluation of removing used nuclear fuel (UNF) from 12 shutdown nuclear power plant sites. At these shutdown sites the nuclear power reactors have been permanently shut down and the sites have been decommissioned or are undergoing decommissioning. The shutdown sites are Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, Zion, Crystal River, Kewaunee, and San Onofre. The evaluation was divided into four components: characterization of the UNF and greater-than-Class C low-level radioactive waste (GTCC waste) inventory; a description of the on-site infrastructure and conditions relevant to transportation of UNF and GTCC waste; an evaluation of the near-site transportation infrastructure and experience relevant to shipping transportation casks containing UNF and GTCC waste, including identification of gaps in information; and, an evaluation of the actions necessary to prepare for and remove UNF and GTCC waste. The primary sources for the inventory of UNF and GTCC waste are the U.S. Department of Energy (DOE) RW-859 used nuclear fuel inventory database, industry sources such as StoreFUEL and SpentFUEL, and government sources such as the U.S. Nuclear Regulatory Commission. The primary sources for information on the conditions of site and near-site transportation infrastructure and experience included observations and information collected during visits to the Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, and Zion sites; information provided by managers at the shutdown sites; Facility Interface Data Sheets compiled for DOE in 2005; Services Planning Documents prepared for DOE in 1993 and 1994; industry publications such as Radwaste Solutions; and Google Earth. State and Regional Group representatives, a Tribal representative, and a Federal Railroad Administration representative participated in six of the shutdown site visits. Every site was found to have at least one off-site transportation mode option for removing its UNF and GTCC waste; some have multiple options. Experience removing large components during reactor decommissioning provided an important source of information used to identify the transportation mode options for the sites. Especially important in conducting the evaluation were site visits, through which information was obtained that would not have been available otherwise. Extensive photographs taken during the site visits proved to be particularly useful in documenting the current conditions at or near the sites. Additional conclusions from this evaluation include: The 12 shutdown sites use designs from 4 different suppliers involving 9 different (horizontal and vertical) dry storage systems that would require the use of 8 different transportation cask designs to remove the UNF and GTCC waste from the shutdown sites; Although there are common aspects, each site has some unique features and/or conditions; Although some regulatory actions will be required, all UNF at the initial 9 shutdown sites (Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, and Zion) is in licensed systems that can be transported, including a small amount of high-burnup fuel; Each site indicated that 2-3 years of advance time would be required for its preparations before shipments could begin; Most sites have more than one transportation option, e.g., rail, barge, or heavy haul truck, as well as constraints and preferences. It is expected that additional site visits will be conducted to add to the information presented in the evaluation.

  14. Dual chamber system providing simultaneous etch and deposition on opposing substrate sides for growing low defect density epitaxial layers

    DOE Patents [OSTI]

    Kulkarni, Nagraj S. (Knoxville, TN); Kasica, Richard J. (Ashburn, VA) ,

    2011-03-08

    A dual-chamber reactor can include a housing enclosing a volume having a divider therein, where the divider defines a first chamber and a second chamber. The divider can include a substrate holder that supports at least one substrate and exposes a first side of the substrate to the first chamber and a second side of the substrate to the second chamber. The first chamber can include an inlet for delivering at least one reagent to the first chamber for forming a film on the first side of the substrate, and the second chamber can include a removal device for removing material from the second side of the substrate.

  15. Low-quality natural gas sulfur removal/recovery

    SciTech Connect (OSTI)

    K. Amo; R.W. Baker; V.D. Helm; T. Hofmann; K.A. Lokhandwala; I. Pinnau; M.B. Ringer; T.T. Su; L. Toy; J.G. Wijmans

    1998-01-29

    A significant fraction of U.S. natural gas reserves are subquality due to the presence of acid gases and nitrogen; 13% of existing reserves (19 trillion cubic feed) may be contaminated with hydrogen sulfide. For natural gas to be useful as fuel and feedstock, this hydrogen sulfide has to be removed to the pipeline specification of 4 ppm. The technology used to achieve these specifications has been amine, or similar chemical or physical solvent, absorption. Although mature and widely used in the gas industry, absorption processes are capital and energy-intensive and require constant supervision for proper operation. This makes these processes unsuitable for treating gas at low throughput, in remote locations, or with a high concentration of acid gases. The U.S. Department of Energy, recognizes that exploitation of smaller, more sub-quality resources will be necessary to meet demand as the large gas fields in the U.S. are depleted. In response to this need, Membrane Technology and Research, Inc. (MTR) has developed membranes and a membrane process for removing hydrogen sulfide from natural gas. During this project, high-performance polymeric thin-film composite membranes were brought from the research stage to field testing. The membranes have hydrogen sulfide/methane selectivities in the range 35 to 60, depending on the feed conditions, and have been scaled up to commercial-scale production. A large number of spiral-wound modules were manufactured, tested and optimized during this project, which culminated in a field test at a Shell facility in East Texas. The short field test showed that membrane module performance on an actual natural gas stream was close to that observed in the laboratory tests with cleaner streams. An extensive technical and economic analysis was performed to determine the best applications for the membrane process. Two areas were identified: the low-flow-rate, high-hydrogen-sulfide-content region and the high-flow-rate, high-hydrogen-sulfide-content region. In both regions the MTR membrane process will be combined with another process to provide the necessary hydrogen sulfide removal from the natural gas. In the first region the membrane process will be combined with the SulfaTreat fixed-bed absorption process, and in the second region the membrane process will be combined with a conventional absorption process. Economic analyses indicate that these hybrid processes provide 20-40% cost savings over stand-alone absorption technologies.

  16. FLOWSHEET FOR ALUMINUM REMOVAL FROM SLUDGE BATCH 6

    SciTech Connect (OSTI)

    Pike, J; Jeffrey Gillam, J

    2008-12-17

    Samples of Tank 12 sludge slurry show a substantially larger fraction of aluminum than originally identified in sludge batch planning. The Liquid Waste Organization (LWO) plans to formulate Sludge Batch 6 (SB6) with about one half of the sludge slurry in Tank 12 and one half of the sludge slurry in Tank 4. LWO identified aluminum dissolution as a method to mitigate the effect of having about 50% more solids in High Level Waste (HLW) sludge than previously planned. Previous aluminum dissolution performed in a HLW tank in 1982 was performed at approximately 85 C for 5 days and dissolved nearly 80% of the aluminum in the sludge slurry. In 2008, LWO successfully dissolved 64% of the aluminum at approximately 60 C in 46 days with minimal tank modifications and using only slurry pumps as a heat source. This report establishes the technical basis and flowsheet for performing an aluminum removal process in Tank 51 for SB6 that incorporates the lessons learned from previous aluminum dissolution evolutions. For SB6, aluminum dissolution process temperature will be held at a minimum of 65 C for at least 24 days, but as long as practical or until as much as 80% of the aluminum is dissolved. As planned, an aluminum removal process can reduce the aluminum in SB6 from about 84,500 kg to as little as 17,900 kg with a corresponding reduction of total insoluble solids in the batch from 246,000 kg to 131,000 kg. The extent of the reduction may be limited by the time available to maintain Tank 51 at dissolution temperature. The range of dissolution in four weeks based on the known variability in dissolution kinetics can range from 44 to more than 80%. At 44% of the aluminum dissolved, the mass reduction is approximately 1/2 of the mass noted above, i.e., 33,300 kg of aluminum instead of 66,600 kg. Planning to reach 80% of the aluminum dissolved should allow a maximum of 81 days for dissolution and reduce the allowance if test data shows faster kinetics. 47,800 kg of the dissolved aluminum will be stored in Tank 8 and 21,000 kg will be stored in saltcake via evaporation. Up to 77% of the total aluminum planned for SB6 may be removed via aluminum dissolution. Storage of the aluminum-laden supernate in Tank 8 will require routine evaluation of the free hydroxide concentration in order to maintain aluminum in solution. Periodic evaluation will be established on concurrent frequency with corrosion program samples as previously established for aluminum-laden supernate from SB5 that is stored in Tank 11.

  17. Remote area wind energy harvesting for low-power autonomous sensors Abstract--A growing demand for deployment of autonomous

    E-Print Network [OSTI]

    Remote area wind energy harvesting for low-power autonomous sensors Abstract--A growing demand a wide range of wind speeds. Results show that power harvesting capability using the discussed alternator electronics to be less than the available power for harvest, which varies as a function of wind speed

  18. Characterization of Feed Efficiency Traits and Relationships with Temperament, Serum Hormones and Serum Metabolites in Growing Brangus Heifers 

    E-Print Network [OSTI]

    Gomez, Robynne 1977-

    2010-09-03

    metabolites in growing heifers. A 4 yr study (n = 114-119 heifers/yr) was conducted with Brangus heifers (Initial BW = 271 ± 26 kg) that were weaned for 25.5 ± 8.6 d prior to high roughage diet adaptation (ME = 2.0 Mcal/kg DM). Individual dry matter intakes...

  19. Growing a multi-class classifier with a reject option D.M.J. Tax *, R.P.W. Duin

    E-Print Network [OSTI]

    Duin, Robert P.W.

    Growing a multi-class classifier with a reject option D.M.J. Tax *, R.P.W. Duin Information Communicated by F. Roli Keywords: Multi-class classification Outlier detection Rejection a b s t r a c by estimating the class densities and assigning an object to the class with the highest posterior probability

  20. Abstract--Despite the growing interest in the transmission and storage of electromyographic signals for long periods of

    E-Print Network [OSTI]

    Carvalho, João Luiz

    Abstract--Despite the growing interest in the transmission and storage of electromyographic signals present an algorithm for compression of electromyographic signals based on the JPEG2000 coding system]. However, few methods have been proposed for compression of electromyographic signals. Norris and Lovely [7