National Library of Energy BETA

Sample records for regional reliability organization

  1. Survey of Transmission Cost Allocation Methodologies for Regional Transmission Organizations

    SciTech Connect (OSTI)

    Fink, S.; Porter, K.; Mudd, C.; Rogers, J.

    2011-02-01

    The report presents transmission cost allocation methodologies for reliability transmission projects, generation interconnection, and economic transmission projects for all Regional Transmission Organizations.

  2. Reliable Cellular Automata with SelfOrganization Peter Gacs 1

    E-Print Network [OSTI]

    Gacs, Peter

    Reliable Cellular Automata with Self¬≠Organization Peter G‚??acs 1 Computer Science Department Boston University Boston, MA 02215 gacs@bu.edu Abstract In a noisy cellular automaton, even if it is infinite solution in 2 dimensions has been applied to a simple 3¬≠dimensional fault¬≠tolerant cellular automaton

  3. RELIABLE CELLULAR AUTOMATA WITH SELF-ORGANIZATION PETER G ACS

    E-Print Network [OSTI]

    Gacs, Peter

    RELIABLE CELLULAR AUTOMATA WITH SELF-ORGANIZATION PETER G ¬īACS ABSTRACT. In a probabilistic cellular automaton in which all local transitions have positive probability, the problem of keeping a bit-tolerant cellular automaton. This technique does not help much to solve the following problems: remembering a bit

  4. The Role of Demand Resources In Regional Transmission Expansion Planning and Reliable Operations

    SciTech Connect (OSTI)

    Kirby, Brendan J

    2006-07-01

    Investigating the role of demand resources in regional transmission planning has provided mixed results. On one hand there are only a few projects where demand response has been used as an explicit alternative to transmission enhancement. On the other hand there is a fair amount of demand response in the form of energy efficiency, peak reduction, emergency load shedding, and (recently) demand providing ancillary services. All of this demand response reduces the need for transmission enhancements. Demand response capability is typically (but not always) factored into transmission planning as a reduction in the load which must be served. In that sense demand response is utilized as an alternative to transmission expansion. Much more demand response is used (involuntarily) as load shedding under extreme conditions to prevent cascading blackouts. The amount of additional transmission and generation that would be required to provide the current level of reliability if load shedding were not available is difficult to imagine and would be impractical to build. In a very real sense demand response solutions are equitably treated in every region - when proposed, demand response projects are evaluated against existing reliability and economic criteria. The regional councils, RTOs, and ISOs identify needs. Others propose transmission, generation, or responsive load based solutions. Few demand response projects get included in transmission enhancement plans because few are proposed. But this is only part of the story. Several factors are responsible for the current very low use of demand response as a transmission enhancement alternative. First, while the generation, transmission, and load business sectors each deal with essentially the same amount of electric power, generation and transmission companies are explicitly in the electric power business but electricity is not the primary business focus of most loads. This changes the institutional focus of each sector. Second, market and reliability rules have, understandably, been written around the capabilities and limitations of generators, the historic reliability resources. Responsive load limitations and capabilities are often not accommodated in markets or reliability criteria. Third, because of the institutional structure, demand response alternatives are treated as temporary solutions that can delay but not replace transmission enhancement. Financing has to be based on a three to five year project life as opposed to the twenty to fifty year life of transmission facilities. More can be done to integrate demand response options into transmission expansion planning. Given the societal benefits it may be appropriate for independent transmission planning organizations to take a more proactive role in drawing demand response alternatives into the resource mix. Existing demand response programs provide a technical basis to build from. Regulatory and market obstacles will have to be overcome if demand response alternatives are to be routinely considered in transmission expansion planning.

  5. Comments in response to FERC rulemaking on regional transmission organizations

    E-Print Network [OSTI]

    Joskow, Paul L.

    1999-01-01

    On May 13, 1999, the Federal Energy Regulatory Commission (FERC) issued a Notice of Proposed Rulemaking (NOPR) on Regional Transmission Organizations (RTO). The purpose of the NOPR is to solicit comments on proposed FERC ...

  6. Organizing and Strategizing a Local/Regional Solar Effort

    Broader source: Energy.gov [DOE]

    This webinar, "Organizing and Strategizing A Local/Regional Solar Effort," was originally presented on June 14, 2013 as part of the DOE SunShot Initiative's Solar Action Webinar Series. This includes presentations by a number of the program's grant partners, including three cities and one corporate partner, to provide participants' perspectives and present their local solar strategies.

  7. Central Wind Power Forecasting Programs in North America by Regional Transmission Organizations and Electric Utilities

    SciTech Connect (OSTI)

    Porter, K.; Rogers, J.

    2009-12-01

    The report addresses the implementation of central wind power forecasting by electric utilities and regional transmission organizations in North America.

  8. Transmission Cost Allocation Methodologies for Regional Transmission Organizations

    SciTech Connect (OSTI)

    Fink, S.; Rogers, J.; Porter, K.

    2010-07-01

    This report describes transmission cost allocation methodologies for transmission projects developed to maintain or enhance reliability, to interconnect new generators, or to access new resources and enhance competitive bulk power markets, otherwise known as economic transmission projects.

  9. Central Wind Forecasting Programs in North America by Regional Transmission Organizations and Electric Utilities: Revised Edition

    SciTech Connect (OSTI)

    Rogers, J.; Porter, K.

    2011-03-01

    The report and accompanying table addresses the implementation of central wind power forecasting by electric utilities and regional transmission organizations in North America. The first part of the table focuses on electric utilities and regional transmission organizations that have central wind power forecasting in place; the second part focuses on electric utilities and regional transmission organizations that plan to adopt central wind power forecasting in 2010. This is an update of the December 2009 report, NREL/SR-550-46763.

  10. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    4.IRED (Integration of Renewable Energy Sources and1.Regional Power Grid with renewable Energy Resourcespdf 2. Spanish Renewable Energy Review http://www.erec.org/

  11. Did geomagnetic activity challenge electric power reliability during solar cycle 23? Evidence from the PJM regional transmission

    E-Print Network [OSTI]

    Schrijver, Karel

    geomagnetic storm on 13 March 1989 contributed to the collapse of the Hydro-Quebec power system in CanadaDid geomagnetic activity challenge electric power reliability during solar cycle 23? Evidence from addresses whether geomagnetic activity challenged power system reliability during Solar Cycle 23. Operations

  12. REGIONAL WORKFORCE STUDY PREPARED FOR THE SRS COMMUNITY REUSE ORGANIZATION

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II) by Carbon-RichProton Delivery andInnovations ThatChallengesREGIONAL

  13. POSITION DESCRIPTION National Non Profit Organization Position Title: Regional Program Manager

    E-Print Network [OSTI]

    Bashir, Rashid

    Summary: The Regional Program Manager will be instrumental in helping to drive demand and generate growth partnerships at the regional and state level Communicates organization's mission and value to a broad audience to promote program Manages administrative logistics of establishing and running programs, inclusive

  14. Transmission Reliability Program 2015 Reliability & Markets Peer...

    Office of Environmental Management (EM)

    Transmission Reliability Program 2015 Reliability & Markets Peer Review Materials Available Transmission Reliability Program 2015 Reliability & Markets Peer Review Materials...

  15. Abstract--The increasing attention paid to reliability in regional transmission organizations provide the impetus for the

    E-Print Network [OSTI]

    as the ability of the interconnected system to provide electricity with the appropriate quality under normal. Through this study, we gain insights that the power systems may be operated under a stricter criterion is a highly challenging task, and even more so with the prominence of electricity markets. As system

  16. Electricity Reliability

    E-Print Network [OSTI]

    Post, Wilfred M.

    Electricity Delivery and Energy Reliability High Temperature Superconductivity (HTS) Visualization in the future because they have virtually no resistance to electric current, offering the possibility of new electric power equipment with more energy efficiency and higher capacity than today's systems

  17. Being the partial proceedings of a conference co-organized by the South-African Regional Poverty Network,

    E-Print Network [OSTI]

    Boyer, Edmond

    Being the partial proceedings of a conference co-organized by the South-African Regional Poverty, Southern African governments have identified the eradication or alleviation of poverty as a key objective of developmental programmes. In spite of these repeated articulations and ongoing efforts poverty levels have

  18. Reliable solar: powering communities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II) by Carbon-RichProtonAbout UsRegional companiesReliabilityReliable solar:

  19. CERTS: Consortium for Electric Reliability Technology Solutions - Research Highlights

    SciTech Connect (OSTI)

    Eto, Joseph

    2003-07-30

    Historically, the U.S. electric power industry was vertically integrated, and utilities were responsible for system planning, operations, and reliability management. As the nation moves to a competitive market structure, these functions have been disaggregated, and no single entity is responsible for reliability management. As a result, new tools, technologies, systems, and management processes are needed to manage the reliability of the electricity grid. However, a number of simultaneous trends prevent electricity market participants from pursuing development of these reliability tools: utilities are preoccupied with restructuring their businesses, research funding has declined, and the formation of Independent System Operators (ISOs) and Regional Transmission Organizations (RTOs) to operate the grid means that control of transmission assets is separate from ownership of these assets; at the same time, business uncertainty, and changing regulatory policies have created a climate in which needed investment for transmission infrastructure and tools for reliability management has dried up. To address the resulting emerging gaps in reliability R&D, CERTS has undertaken much-needed public interest research on reliability technologies for the electricity grid. CERTS' vision is to: (1) Transform the electricity grid into an intelligent network that can sense and respond automatically to changing flows of power and emerging problems; (2) Enhance reliability management through market mechanisms, including transparency of real-time information on the status of the grid; (3) Empower customers to manage their energy use and reliability needs in response to real-time market price signals; and (4) Seamlessly integrate distributed technologies--including those for generation, storage, controls, and communications--to support the reliability needs of both the grid and individual customers.

  20. Assessing reliability in energy supply systems

    E-Print Network [OSTI]

    McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

    2007-01-01

    various fuels and energy supply systems. Acknowledgements WeAssessing Reliability in Energy Supply Systems Ryan W.stability of many energy supply regions becomes more

  1. Assessing Reliability in Energy Supply Systems

    E-Print Network [OSTI]

    McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

    2008-01-01

    various fuels and energy supply systems. Acknowledgements WeAssessing Reliability in Energy Supply Systems Ryan W.stability of many energy supply regions becomes more

  2. Photodissociation of organic molecules in star-forming regions, III. Methanol

    E-Print Network [OSTI]

    S. Pilling; R. Neves; A. C. F. Santos; H. M. Boechat-Roberty

    2006-12-15

    The presence of methyl alcohol or methanol (CH$_3$OH) in several astrophysical environments has been characterized by its high abundance that depends on both the production rate and the destruction rate. In the present work, the photoionization and photodissociation processes of methanol have been experimentally studied, employing soft X-ray photons (100-310 eV) from a toroidal grating monochromator (TGM) beamline of the Brazilian Synchrotron Light Laboratory (LNLS). Mass spectra were obtained using the photoelectron photoion coincidence (PEPICO) method. Kinetic energy distribution and abundances for each ionic fragment have been obtained from the analysis of the corresponding peak shapes in the mass spectra. Absolute photoionization and photodissociation cross sections were also determined. We have found, among the channels leading to ionization, about 11-16% of CH$_3$OH survive the soft X-rays photons. This behavior, together with an efficient formation pathways, may be associated with the high column density observed in star-forming regions. The three main photodissociation pathways are represented by COH$^+$ (or HCO$^+$) ion release (with ejection of H$_2$ + H), the dissociation via C-O bond rupture (with strong charge retention preferentially on the methyl fragment) and the ejection of a single energetic (2-4 eV) proton. Since methanol is very abundant in star forming regions, the produced protons could be an alternative route to molecular hydrogenation or a trigger for secondary dissociation processes or even to promote extra heating of the environment.

  3. Transport of organic carbon from the California coast to the slope region: A study of Delta 14 C and delta 13 C signatures of organic compound classes

    E-Print Network [OSTI]

    Hwang, Jeomshik; Druffel, Ellen R. M; Komada, Tomoko

    2005-01-01

    Channel, California, in Shelf Sediment Transport: Processesthat lateral transport of OC on the California margin is an2005 Transport of organic carbon from the California coast

  4. Airborne flux measurements of methane and volatile organic compounds over the Haynesville and Marcellus shale gas production regions

    E-Print Network [OSTI]

    2015-01-01

    of methane emissions from shale gas development, Proc. Natl.and northeastern Marcellus shale gas production regions, J.Haynesville and Marcellus shale gas production regions, J.

  5. Human Reliability Program Overview

    SciTech Connect (OSTI)

    Bodin, Michael

    2012-09-25

    This presentation covers the high points of the Human Reliability Program, including certification/decertification, critical positions, due process, organizational structure, program components, personnel security, an overview of the US DOE reliability program, retirees and academia, and security program integration.

  6. Airborne flux measurements of methane and volatile organic compounds over the Haynesville and Marcellus shale gas production regions

    E-Print Network [OSTI]

    2015-01-01

    natural gas extraction can lead to signi?cant emissions of methane (CH 4 ), volatile organic compounds (VOCs), and nitrogen

  7. Proposed changes to generating capacity 1980-1989 for the contiguous United States: as projected by the Regional Electric Reliability Councils in their April 1, 1980 long-range coordinated planning reports to the Department of Energy

    SciTech Connect (OSTI)

    1980-12-01

    The changes in generating capacity projected for 1980 to 1989 are summarized. Tabulated data provide summaries to the information on projected generating unit construction, retirements, and changes, in several different categories and groupings. The new generating units to be completed by the end of 1989 total 699, representing 259,490 megawatts. This total includes 10 wind power and one fuel cell installations totaling 48.5 MW to be completed by the end of 1989. There are 321 units totaling 13,222 MW to be retired. There are capacity changes due to upratings and deratings. Summary data are presented for: total requirement for electric energy generation for 1985; hydroelectric energy production for 1985; nuclear energy production for 1985; geothermal and other energy production for 1985; approximate non-fossil generation for 1985; range of fossil energy requirements for 1985; actual fossil energy sources 1974 to 1979; estimated range of fossil fuel requirements for 1985; coal capacity available in 1985; and computation of fuel use in 1985. Power plant capacity factors are presented. Extensive data on proposed generating capacity changes by individual units in the 9 Regional Electric Reliability Councils are presented.

  8. Regional Test Centers (RTCs)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    has established five Regional Test Centers (RTCs) across the United States to independently validate the performance and reliability of photovoltaic (PV) systems in different...

  9. Reliability Assessment The Reliability of the

    E-Print Network [OSTI]

    ...................................................................................................................4 SUMMER 2006 HEAT WAVE .......................6 CONSTRUCTION OF NEW TRANSMISSION IS STILL SLOW -- CONTINUES TO FACE OBSTACLES..............................................11 RELIABILITY WILL DEPEND ON CLOSE COORDINATION OF GENERATION AND TRANSMISSION PLANNING

  10. Sandia Energy - Human Reliability Assessment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Human Reliability Assessment Home Stationary Power Nuclear Fuel Cycle Nuclear Energy Safety Technologies Risk and Safety Assessment Human Reliability Assessment Human Reliability...

  11. Airborne flux measurements of methane and volatile organic compounds over the Haynesville and Marcellus shale gas production regions

    E-Print Network [OSTI]

    2015-01-01

    emissions from oil and gas production pads using mobileuxes over other oil and gas production regions using eddycompounds (VOCs) from oil and gas production may have large

  12. Airborne flux measurements of methane and volatile organic compounds over the Haynesville and Marcellus shale gas production regions

    E-Print Network [OSTI]

    2015-01-01

    in the Haynesville Shale, Environ. Sci. Technol. , 44(24),of methane emissions from shale gas development, Proc. Natl.and northeastern Marcellus shale gas production regions, J.

  13. Medical Aspects of Reliability

    SciTech Connect (OSTI)

    Atencio, Julian J.

    2014-05-05

    This presentation covers the medical evaluation as part of a human reliability program, particularly the various medical qualifications and potential disqualifiers.

  14. Reliable Energy Integration of

    E-Print Network [OSTI]

    Zeng, Ning

    Engineering SustainabilityWorkshop #12;Cost of EnergyTrends Engineering SustainabilityWorkshop #12;Why GoReliable Energy Integration of Offshore Wind Aris Christou University of Maryland College Park MD Access is Difficult, and Costly: Require Minimum Maintenance and High Reliability Engineering

  15. Hawaii electric system reliability.

    SciTech Connect (OSTI)

    Silva Monroy, Cesar Augusto; Loose, Verne William

    2012-09-01

    This report addresses Hawaii electric system reliability issues; greater emphasis is placed on short-term reliability but resource adequacy is reviewed in reference to electric consumers' views of reliability %E2%80%9Cworth%E2%80%9D and the reserve capacity required to deliver that value. The report begins with a description of the Hawaii electric system to the extent permitted by publicly available data. Electrical engineering literature in the area of electric reliability is researched and briefly reviewed. North American Electric Reliability Corporation standards and measures for generation and transmission are reviewed and identified as to their appropriateness for various portions of the electric grid and for application in Hawaii. Analysis of frequency data supplied by the State of Hawaii Public Utilities Commission is presented together with comparison and contrast of performance of each of the systems for two years, 2010 and 2011. Literature tracing the development of reliability economics is reviewed and referenced. A method is explained for integrating system cost with outage cost to determine the optimal resource adequacy given customers' views of the value contributed by reliable electric supply. The report concludes with findings and recommendations for reliability in the State of Hawaii.

  16. Airborne flux measurements of methane and volatile organic compounds over the Haynesville and Marcellus shale gas production regions

    E-Print Network [OSTI]

    2015-01-01

    of methane emissions from oil and gas production pads using2015), In?uence of oil and gas ?eld operations on spatialux measurements over oil and gas extraction regions ē

  17. Consortium for Electric Reliability Technology Solutions Grid of the Future White Paper on Review of Recent Reliability Issues and Systems Events

    SciTech Connect (OSTI)

    Hauer, John F.; Dagle, Jeffery E.

    1999-12-01

    This report is one of six reports developed under the U.S. Department of Energy (DOE) program in Power System Integration and Reliability (PSIR). The objective of this report is to review, analyze, and evaluate critical reliability issues demonstrated by recent disturbance events in the North America power system. Eleven major disturbances are examined, most occurring in this decade. The strategic challenge is that the pattern of technical need has persisted for a long period of time. For more than a decade, anticipation of market deregulation has been a major disincentive to new investments in system capacity. It has also inspired reduced maintenance of existing assets. A massive infusion of better technology is emerging as the final option to continue reliable electrical services. If an investment in better technology will not be made in a timely manner, then North America should plan its adjustments to a very different level of electrical service. It is apparent that technical operations staff among the utilities can be very effective at marshaling their forces in the immediate aftermath of a system emergency, and that serious disturbances often lead to improved mechanisms for coordinated operation. It is not at all apparent that such efforts can be sustained through voluntary reliability organizations in which utility personnel external to those organizations do most of the technical work. The eastern interconnection shows several situations in which much of the technical support has migrated from the utilities to the Independent System Operator (ISO), and the ISO staffs or shares staff with the regional reliability council. This process may be a natural and very positive consequence of utility restructuring. If so, the process should be expedited in regions where it is less advanced.

  18. Measurement Practices for Reliability and Power Quality

    SciTech Connect (OSTI)

    Kueck, JD

    2005-05-06

    This report provides a distribution reliability measurement ''toolkit'' that is intended to be an asset to regulators, utilities and power users. The metrics and standards discussed range from simple reliability, to power quality, to the new blend of reliability and power quality analysis that is now developing. This report was sponsored by the Office of Electric Transmission and Distribution, U.S. Department of Energy (DOE). Inconsistencies presently exist in commonly agreed-upon practices for measuring the reliability of the distribution systems. However, efforts are being made by a number of organizations to develop solutions. In addition, there is growing interest in methods or standards for measuring power quality, and in defining power quality levels that are acceptable to various industries or user groups. The problems and solutions vary widely among geographic areas and among large investor-owned utilities, rural cooperatives, and municipal utilities; but there is still a great degree of commonality. Industry organizations such as the National Rural Electric Cooperative Association (NRECA), the Electric Power Research Institute (EPRI), the American Public Power Association (APPA), and the Institute of Electrical and Electronics Engineers (IEEE) have made tremendous strides in preparing self-assessment templates, optimization guides, diagnostic techniques, and better definitions of reliability and power quality measures. In addition, public utility commissions have developed codes and methods for assessing performance that consider local needs. There is considerable overlap among these various organizations, and we see real opportunity and value in sharing these methods, guides, and standards in this report. This report provides a ''toolkit'' containing synopses of noteworthy reliability measurement practices. The toolkit has been developed to address the interests of three groups: electric power users, utilities, and regulators. The report will also serve to support activities to develop and share information among industry and regulatory participants about critical resources and practices. The toolkit has been developed by investigating the status of indices and definitions, surveying utility organizations on information sharing, and preparing summaries of reliability standards and monitoring requirements--the issues, needs, work under way, existing standards, practices and guidelines--for the following three classifications: (1) terms and definitions of reliability; (2) power quality standards, guidelines, and measurements; and (3) activities and organizations developing and sharing information on distribution reliability. As these synopses of reliability measurement practices are provided, it must be noted that an economic penalty may be associated with requiring too high a reliability level from the distribution system for all customers. It may be appropriate for the distribution system to supply only some base, generally accepted level of reliability. This base level would be adequate for the majority of customers. Users who need a higher level may find it economical to supply using distributed energy resources (DER) and other local solutions to reliability and power quality needs. Local solutions implemented by the customer may be the most cost-effective method for addressing the more stringent needs of a digital economy. These local solutions include energy storage, small distributed generators, and microgrids. This report also considers the market's role in addressing reliability issues and requirements. The customer's needs are discussed in view of issues such as power quality requirements of digital electronic equipment, the cost of outages, the cost of storage and new infrastructure, and natural gas prices. The market role in addressing these issues and requirements is explored. The economic considerations associated with the reliability issues are discussed, as well as the levels at which these economic decisions could be made. Finally, a discussion is provided of the role DER could play in addressing

  19. Reliability and Safety

    Broader source: Energy.gov [DOE]

    DOE solar reliability and safety research and development (R&D) focuses on testing photovoltaic (PV) modules, inverters, and systems for long-term performance, and helping investors, consumers,...

  20. Solid State Lighting Reliability

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solid State Lighting Reliability 2015Building Technologies Office Peer Review Lynn Davis, PhD RTI International ldavis@rti.org --- 919-316-3325 Project Summary Timeline: Start...

  1. Characterizing the Aging of Biomass Burning Organic Aerosol by Use of Mixing Ratios: A Meta-analysis of Four Regions

    E-Print Network [OSTI]

    Jimenez, Jose-Luis

    on climate through perturbations to Earth's solar radiation balance. Around 90% of total global primary the potential for radiative forcing. Sources in tropical regions account for 80% of global BBOA emissions,2 providing a significant potential radiative forcing given the elevated levels of solar irradiance

  2. Gearbox Reliability Collaborative Update (Presentation)

    SciTech Connect (OSTI)

    Sheng, S.

    2013-10-01

    This presentation was given at the Sandia Reliability Workshop in August 2013 and provides information on current statistics, a status update, next steps, and other reliability research and development activities related to the Gearbox Reliability Collaborative.

  3. Photovoltaic module reliability workshop

    SciTech Connect (OSTI)

    Mrig, L. (ed.)

    1990-01-01

    The paper and presentations compiled in this volume form the Proceedings of the fourth in a series of Workshops sponsored by Solar Energy Research Institute (SERI/DOE) under the general theme of photovoltaic module reliability during the period 1986--1990. The reliability Photo Voltaic (PV) modules/systems is exceedingly important along with the initial cost and efficiency of modules if the PV technology has to make a major impact in the power generation market, and for it to compete with the conventional electricity producing technologies. The reliability of photovoltaic modules has progressed significantly in the last few years as evidenced by warranties available on commercial modules of as long as 12 years. However, there is still need for substantial research and testing required to improve module field reliability to levels of 30 years or more. Several small groups of researchers are involved in this research, development, and monitoring activity around the world. In the US, PV manufacturers, DOE laboratories, electric utilities and others are engaged in the photovoltaic reliability research and testing. This group of researchers and others interested in this field were brought together under SERI/DOE sponsorship to exchange the technical knowledge and field experience as related to current information in this important field. The papers presented here reflect this effort.

  4. Effect of Terrestrial and Marine Organic Aerosol on Regional and Global Climate: Model Development, Application, and Verification with Satellite Data

    SciTech Connect (OSTI)

    Meskhidze, Nicholas; Zhang, Yang; Kamykowski, Daniel

    2012-03-28

    In this DOE project the improvements to parameterization of marine primary organic matter (POM) emissions, hygroscopic properties of marine POM, marine isoprene derived secondary organic aerosol (SOA) emissions, surfactant effects, new cloud droplet activation parameterization have been implemented into Community Atmosphere Model (CAM 5.0), with a seven mode aerosol module from the Pacific Northwest National Laboratory (PNNL)√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?s Modal Aerosol Model (MAM7). The effects of marine aerosols derived from sea spray and ocean emitted biogenic volatile organic compounds (BVOCs) on microphysical properties of clouds were explored by conducting 10 year CAM5.0-MAM7 model simulations at a grid resolution 1.9√?¬?√?¬?√?¬?√?¬į√?¬?√?¬?√?¬?√?¬?2.5√?¬?√?¬?√?¬?√?¬į with 30 vertical layers. Model-predicted relationship between ocean physical and biological systems and the abundance of CCN in remote marine atmosphere was compared to data from the A-Train satellites (MODIS, CALIPSO, AMSR-E). Model simulations show that on average, primary and secondary organic aerosol emissions from the ocean can yield up to 20% increase in Cloud Condensation Nuclei (CCN) at 0.2% Supersaturation, and up to 5% increases in droplet number concentration of global maritime shallow clouds. Marine organics were treated as internally or externally mixed with sea salt. Changes associated with cloud properties reduced (absolute value) the model-predicted short wave cloud forcing from -1.35 Wm-2 to -0.25 Wm-2. By using different emission scenarios, and droplet activation parameterizations, this study suggests that addition of marine primary aerosols and biologically generated reactive gases makes an important difference in radiative forcing assessments. All baseline and sensitivity simulations for 2001 and 2050 using global-through-urban WRF/Chem (GU-WRF) were completed. The main objective of these simulations was to evaluate the capability of GU-WRF for an accurate representation of the global atmosphere by exploring the most accurate configuration of physics options in GWRF for global scale modeling in 2001 at a horizontal grid resolution of 1√?¬?√?¬?√?¬?√?¬į x 1√?¬?√?¬?√?¬?√?¬į. GU-WRF model output was evaluated using observational datasets from a variety of sources including surface based observations (NCDC and BSRN), model reanalysis (NCEP/ NCAR Reanalysis and CMAP), and remotely-sensed data (TRMM) to evaluate the ability of GU-WRF to simulate atmospheric variables at the surface as well as aloft. Explicit treatment of nanoparticles produced from new particle formation in GU-WRF/Chem-MADRID was achieved by expanding particle size sections from 8 to 12 to cover particles with the size range of 1.16 nm to 11.6 √?¬?√?¬?√?¬?√?¬Ķm. Simulations with two different nucleation parameterizations were conducted for August 2002 over a global domain at a 4√?¬?√?¬?√?¬?√?¬ļ by 5√?¬?√?¬?√?¬?√?¬ļ horizontal resolution. The results are evaluated against field measurement data from the 2002 Aerosol Nucleation and Real Time Characterization Experiment (ANARChE) in Atlanta, Georgia, as well as satellite and reanalysis data. We have also explored the relationship between √?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?clean marine√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬Ě aerosol optical properties and ocean surface wind speed using remotely sensed data from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on board the CALIPSO satellite and the Advanced Microwave Scanning Radiometer (AMSR-E) on board the AQUA satellite. Detailed data analyses

  5. ISSAT 2012 KCoverage Reliability Evaluation K-COVERAGE RELIABILITY EVALUATION

    E-Print Network [OSTI]

    Xing, Liudong

    #12;7/20/2012 ISSAT 2012 KCoverage Reliability Evaluation forWSNs 2 Introduction Wireless sensor;7/20/2012 ISSAT 2012 KCoverage Reliability Evaluation forWSNs 7 Model 13 Consider a set of sensor nodes (SN7/20/2012 ISSAT 2012 KCoverage Reliability Evaluation forWSNs 1 K-COVERAGE RELIABILITY EVALUATION

  6. Reliability of Electrical Interconnects (Presentation)

    SciTech Connect (OSTI)

    Devoto, D.

    2014-06-01

    This presentation discusses the status of NREL's research on the reliability of electrical interconnects.

  7. Human Reliability Program Workshop

    SciTech Connect (OSTI)

    Landers, John; Rogers, Erin; Gerke, Gretchen

    2014-05-18

    A Human Reliability Program (HRP) is designed to protect national security as well as worker and public safety by continuously evaluating the reliability of those who have access to sensitive materials, facilities, and programs. Some elements of a site HRP include systematic (1) supervisory reviews, (2) medical and psychological assessments, (3) management evaluations, (4) personnel security reviews, and (4) training of HRP staff and critical positions. Over the years of implementing an HRP, the Department of Energy (DOE) has faced various challenges and overcome obstacles. During this 4-day activity, participants will examine programs that mitigate threats to nuclear security and the insider threat to include HRP, Nuclear Security Culture (NSC) Enhancement, and Employee Assistance Programs. The focus will be to develop an understanding of the need for a systematic HRP and to discuss challenges and best practices associated with mitigating the insider threat.

  8. Assessing I-Grid(TM) web-based monitoring for power quality and reliability benchmarking

    E-Print Network [OSTI]

    Divan, Deepak; Brumsickle, William; Eto, Joseph

    2003-01-01

    not affect the regional power grid. Page 7 of 10 January 23,Paradigm in Distribution Grid Power Quality And ReliabilitySheehan 2002]. The I-Grid power quality and reliability

  9. Solid State Lighting Reliability

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankADVANCED MANUFACTURINGEnergy BillsNo.Hydrogen4EnergySolid State Lighting Reliability 2014 Building

  10. Regional Transmission Projects: Finding Solutions

    SciTech Connect (OSTI)

    The Keystone Center

    2005-06-15

    The Keystone Center convened and facilitated a year-long Dialogue on "Regional Transmission Projects: Finding Solutions" to develop recommendations that will help address the difficult and contentious issues related to expansions of regional electric transmission systems that are needed for reliable and economic transmission of power within and across regions. This effort brought together a cross-section of affected stakeholders and thought leaders to address the problem with the collective wisdom of their experience and interests. Transmission owners sat at the table with consumer advocates and environmental organizations. Representatives from regional transmission organizations exchanged ideas with state and federal regulators. Generation developers explored common interests with public power suppliers. Together, the Dialogue participants developed consensus solutions about how to begin unraveling some of the more intractable issues surrounding identification of need, allocation of costs, and reaching consensus on siting issues that can frustrate the development of regional transmission infrastructure. The recommendations fall into three broad categories: 1. Recommendations on appropriate institutional arrangements and processes for achieving regional consensus on the need for new or expanded transmission infrastructure 2. Recommendations on the process for siting of transmission lines 3. Recommendations on the tools needed to support regional planning, cost allocation, and siting efforts. List of Dialogue participants: List of Dialogue Participants: American Electric Power American Transmission Company American Wind Energy Association California ISO Calpine Corporation Cinergy Edison Electric Institute Environmental Defense Federal Energy Regulatory Commission Great River Energy International Transmission Company ISO-New England Iowa Public Utility Board Kanner & Associates Midwest ISO National Association of Regulatory Utility Commissioners National Association of State Utility Consumer Advocates National Grid Northeast Utilities PA Office of Consumer Advocates Pacific Gas & Electric Corporation Pennsylvania Public Utility Commission PJM Interconnection The Electricity Consumers Resource Council U.S. Department of Energy US Department of the Interior Van Ness Feldman Western Interstate Energy Board Wind on the Wires Wisconsin Public Service Commission Xcel Energy

  11. Value-based reliability transmission planning

    SciTech Connect (OSTI)

    Dalton, J.G. III; Garrison, D.L.; Fallon, C.M.

    1996-08-01

    This paper presents a new value-based reliability planning (VBRP) process proposed for planning Duke Power Company`s (DPC) regional transmission system. All transmission served customers are fed from DPC`s regional transmission system which consists of a 44-kV predominantly radial system and a 100-kV predominantly non-radial system. In the past, any single contingency that could occur during system peak conditions and cause a thermal overload required the overloaded facility to be upgraded, regardless of the costs or the likelihood of the overload occurring. The new VBRP process is based on transmission system reliability evaluation and includes the following important elements: (1) a ten-year historical data base describing the probabilities of forced outages for lines and transformers; (2) a five-year average load duration curve describing the probability of an overload should a contingency occur; (3) a customer outage cost data base; (4) and probabilistic techniques. The new process attempts to balance the costs of improving service reliability with the benefits or value that these improvements bring to these customers. The objective is to provide the customers their required level of reliability while minimizing the Total Cost of their electric service.

  12. Sandia Energy - PV Systems Reliability

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Home Stationary Power Energy Conversion Efficiency Solar Energy Photovoltaics PV Systems Reliability PV Systems ReliabilityCoryne Tasca2015-05-08T03:40:54+00:00 Sandia...

  13. Testing for PV Reliability (Presentation)

    SciTech Connect (OSTI)

    Kurtz, S.; Bansal, S.

    2014-09-01

    The DOE SUNSHOT workshop is seeking input from the community about PV reliability and how the DOE might address gaps in understanding. This presentation describes the types of testing that are needed for PV reliability and introduces a discussion to identify gaps in our understanding of PV reliability testing.

  14. Analysis and design of reliable nanometer circuits

    E-Print Network [OSTI]

    Zhao, Chong

    2007-01-01

    OF CALIFORNIA, SAN DIEGO Analysis and Design of ReliableTHE DISSERTATION Analysis and Design of Reliable Nanometerthe difficulty in analysis and design of reliable digital

  15. Sandia Energy - Inverter Reliability Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    lifetime cost must decrease for photovoltaics to be financially viable. Currently the cost and reliability of PV modules is improving faster than the rest of the system. One...

  16. Southeast Regional Clean Energy Policy Analysis

    Office of Energy Efficiency and Renewable Energy (EERE)

    This report covers the states that largely fall into the Southeastern Reliability Corporation (SERC) region: Alabama, Arkansas, Georgia, Louisiana, Kentucky, Missouri, Mississippi, North Carolina, South Carolina, and Tennessee.

  17. Subsea pipeline isolation systems: Reliability and costs

    SciTech Connect (OSTI)

    Masheder, R.R.

    1996-08-01

    Since the Piper Alpha disaster, more than 80 subsea isolation systems (SSIS) have been installed in subsea gas and oil pipelines in the U.K. continental shelf at an estimated cost in the region of {Brit_pounds}500 million. The reliability and costs of these installations have now been assessed between Dec. 1992 and Oct. 1993. This assessment was based upon comprehensive reliability and cost databases which were established so that the studies could be based upon factual information in order to obtain a current status as required by the sponsoring group. The study consultants report findings have now been consolidated into a report by the UKOOA Pipeline Valve Work Group. Probabilities of failure for different types of valves and systems have been assessed and expenditures broken down and compared. The results of the studies and the conclusions drawn by UKOOA Pipeline Valve Group and the HSE Offshore Safety Division are presented in this paper.

  18. Reliability Question Comment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II) by Carbon-RichProtonAbout UsRegional companies

  19. LMS Reliability FMECA and SPFS

    E-Print Network [OSTI]

    Rathbun, Julie A.

    LMS Reliability FMECA and SPFS Contract No. NAS 9-5829 NO. ATM 97C PAGE 1 REV. MO. B OF~- DATE 21 will use the fixed mode ionization voltage. Prepared by: Approved by: .... ~~~lfo*R. Hiebert LMS III v VI LMS Reliability FMECA and SPFS Contract No. NAS9-5829 TABLE CJF CONTENTS DISCUSSION

  20. Organic photosensitive devices

    DOE Patents [OSTI]

    Peumans, Peter; Forrest, Stephen R.

    2013-01-22

    A photoactive device is provided. The device includes a first electrode, a second electrode, and a photoactive region disposed between and electrically connected to the first and second electrodes. The photoactive region further includes an organic donor layer and an organic acceptor layer that form a donor-acceptor heterojunction. The mobility of holes in the organic donor region and the mobility of electrons in the organic acceptor region are different by a factor of at least 100, and more preferably a factor of at least 1000. At least one of the mobility of holes in the organic donor region and the mobility of electrons in the organic acceptor region is greater than 0.001 cm.sup.2/V-sec, and more preferably greater than 1 cm.sup.2/V-sec. The heterojunction may be of various types, including a planar heterojunction, a bulk heterojunction, a mixed heterojunction, and a hybrid planar-mixed heterojunction.

  1. Reliability Technology earns prestigious Los Alamos award

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II) by Carbon-RichProtonAbout UsRegional companiesReliability Technology

  2. Sandia Energy - PV Systems Reliability

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    studies such as Accelerated Life Testing (ALT) and Failure Modes and Effects Analysis (FMEA). SNL has also partnered with a utility to create a data-driven Reliability Block...

  3. Reliability and Competitive Electricity Markets

    E-Print Network [OSTI]

    Joskow, Paul; Tirole, Jean

    2006-03-14

    Deregulation of the electricity sector has resulted in conflict between the economic aims of creating competitive wholesale and retail markets, and an engineering focus on reliability of supply. The paper starts by deriving the optimal prices...

  4. US Nuclear Regulatory Commission functional organization charts

    SciTech Connect (OSTI)

    Not Available

    1988-01-01

    This document provides functional organization charts for all NRC Offices and Regions, and their components.

  5. NORTH AMERICAN ELECTRIC RELIABILITY COUNCIL: Preliminary Disturbance...

    Energy Savers [EERE]

    Report More Documents & Publications North American Electric Reliability Council Power Outage Update North American Electric Reliability Council Outage Announcement Electric System...

  6. Distributed Generation Operational Reliability, Executive Summary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reliability, Executive Summary Report, January 2004 Distributed Generation Operational Reliability, Executive Summary Report, January 2004 This report summarizes the results of the...

  7. Distributed Generation Operational Reliability and Availability...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reliability and Availability Database, Final Report, January 2004 Distributed Generation Operational Reliability and Availability Database, Final Report, January 2004 This final...

  8. Recommendations to Address Power Reliability Concerns Raised...

    Office of Environmental Management (EM)

    to Address Power Reliability Concerns Raised as a Result of Pending Environmental Regulations for Electric Generation Stations Recommendations to Address Power Reliability Concerns...

  9. Sandia Energy - Continuous Reliability Enhancement for Wind ...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Continuous Reliability Enhancement for Wind (CREW): Project Update Home Renewable Energy Energy News Wind Energy News & Events Systems Analysis Continuous Reliability Enhancement...

  10. NREL Publishes Gearbox Reliability Collaborative Findings Report...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Publishes Gearbox Reliability Collaborative Findings Report NREL Publishes Gearbox Reliability Collaborative Findings Report October 3, 2011 - 12:56pm Addthis This is an excerpt...

  11. LMS RELIABILITY PART APPLICATION ANALYSIS

    E-Print Network [OSTI]

    Rathbun, Julie A.

    ( LMS RELIABILITY PART APPLICATION ANALYSIS Contract No. NAS 9-5829 MO. ATM-966 PAGE 1 RIV. NO, B 3. 0 3. I 3. 2 3.3 3. 3. I 3. 3. 2 3.3.3 3. 3. 4 4. 0 PARA. NO. 1. 0 1.1 LMS RELIABILITY PART 1. 5 1. 6 1. 7 2. 0 2. 1 2. 2 2. 2. 1 2. 2. 2 2. 2. 3 2. 2. 4 -:-?∑ 2. ,5 2. 3 2. 3. 1 LMS

  12. Reliability in the design phase

    SciTech Connect (OSTI)

    Siahpush, A.S.; Hills, S.W.; Pham, H. (EG and G Idaho, Inc., Idaho Falls, ID (United States)); Majumdar, D. (USDOE Idaho Field Office, Idaho Falls, ID (United States))

    1991-12-01

    A study was performed to determine the common methods and tools that are available to calculated or predict a system's reliability. A literature review and software survey are included. The desired product of this developmental work is a tool for the system designer to use in the early design phase so that the final design will achieve the desired system reliability without lengthy testing and rework. Three computer programs were written which provide the first attempt at fulfilling this need. The programs are described and a case study is presented for each one. This is a continuing effort which will be furthered in FY-1992. 10 refs.

  13. Reliability in the design phase

    SciTech Connect (OSTI)

    Siahpush, A.S.; Hills, S.W.; Pham, H. [EG and G Idaho, Inc., Idaho Falls, ID (United States); Majumdar, D. [USDOE Idaho Field Office, Idaho Falls, ID (United States)

    1991-12-01

    A study was performed to determine the common methods and tools that are available to calculated or predict a system`s reliability. A literature review and software survey are included. The desired product of this developmental work is a tool for the system designer to use in the early design phase so that the final design will achieve the desired system reliability without lengthy testing and rework. Three computer programs were written which provide the first attempt at fulfilling this need. The programs are described and a case study is presented for each one. This is a continuing effort which will be furthered in FY-1992. 10 refs.

  14. Demand Response and Electric Grid Reliability

    E-Print Network [OSTI]

    Wattles, P.

    2012-01-01

    and Regional Transmission Organizations are the ?air traffic controllers? of the bulk electric power grids 4 Power supply (generation) must match load (demand) CATEE Conference October 10, 2012 ? The fundamental concept behind ERCOT operations... changes or incentives.? (FERC) ? ?Changes in electric use by demand-side resources from their normal consumption patterns in response to changes in the price of electricity, or to incentive payments designed to induce lower electricity use at times...

  15. Modeling regional power transfers

    SciTech Connect (OSTI)

    Kavicky, J.A.; Veselka, T.D.

    1994-03-01

    The Spot Market Network (SMN) model was used to estimate spot market transactions and prices between various North American Electric Reliability Council (NERC) regions for summer on-peak situations. A preliminary analysis of new or proposed additions to the transmission network was performed. The effects of alternative exempt wholesale generator (EWG) options on spot market transactions and the transmission system are also studied. This paper presents the SMN regional modelling approach and summarizes simulation results. Although the paper focuses on a regional network representation, a discussion of how the SMN model was used to represent a detailed utility-level network is also presented.

  16. Organic photosensitive devices

    DOE Patents [OSTI]

    Rand, Barry P; Forrest, Stephen R

    2013-11-26

    The present invention generally relates to organic photosensitive optoelectronic devices. More specifically, it is directed to organic photosensitive optoelectronic devices having a photoactive organic region containing encapsulated nanoparticles that exhibit plasmon resonances. An enhancement of the incident optical field is achieved via surface plasmon polariton resonances. This enhancement increases the absorption of incident light, leading to a more efficient device.

  17. Wind turbine reliability database update.

    SciTech Connect (OSTI)

    Peters, Valerie A.; Hill, Roger Ray; Stinebaugh, Jennifer A.; Veers, Paul S.

    2009-03-01

    This report documents the status of the Sandia National Laboratories' Wind Plant Reliability Database. Included in this report are updates on the form and contents of the Database, which stems from a fivestep process of data partnerships, data definition and transfer, data formatting and normalization, analysis, and reporting. Selected observations are also reported.

  18. Photovoltaic performance and reliability workshop

    SciTech Connect (OSTI)

    Kroposki, B.

    1996-10-01

    This proceedings is the compilation of papers presented at the ninth PV Performance and Reliability Workshop held at the Sheraton Denver West Hotel on September 4--6, 1996. This years workshop included presentations from 25 speakers and had over 100 attendees. All of the presentations that were given are included in this proceedings. Topics of the papers included: defining service lifetime and developing models for PV module lifetime; examining and determining failure and degradation mechanisms in PV modules; combining IEEE/IEC/UL testing procedures; AC module performance and reliability testing; inverter reliability/qualification testing; standardization of utility interconnect requirements for PV systems; need activities to separate variables by testing individual components of PV systems (e.g. cells, modules, batteries, inverters,charge controllers) for individual reliability and then test them in actual system configurations; more results reported from field experience on modules, inverters, batteries, and charge controllers from field deployed PV systems; and system certification and standardized testing for stand-alone and grid-tied systems.

  19. Latest Data Show Strong Fertility Center Offers Region's Best IVF Success Rates! The Society for Assisted Reproductive Technology (SART), the primary organization of

    E-Print Network [OSTI]

    Goldman, Steven A.

    Latest Data Show Strong Fertility Center Offers Region's Best IVF Success Rates! The Society Fertility Center surpasses the national average for IVF in women under 35 years of age. Over 51% of embryo transfers in women under age 35 resulted in live births. In fact, Strong Fertility Center's IVF success

  20. Assessing Reliability in Energy Supply Systems

    E-Print Network [OSTI]

    McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

    2008-01-01

    total of 15 metrics. Pathway reliability General objectives Adequacy Security Functional zones Primary energy supply

  1. Assessing reliability in energy supply systems

    E-Print Network [OSTI]

    McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

    2007-01-01

    total of 15 metrics. Pathway reliability General objectives Adequacy Security Functional zones Primary energy supply

  2. 2012 Reliability & Markets Peer Review | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reliability & Markets Peer Review 2012 Reliability & Markets Peer Review The Transmission Reliability R&D Reliability & Markets Peer Review included 11 presentations over 2 days on...

  3. Texas State Planning Region 3 Report of Regional Transportation Coordination†

    E-Print Network [OSTI]

    Nortex Regional Planning Commission

    2006-12-01

    stream_source_info Nortex Regional Transportation Coordination Plan.pdf.txt stream_content_type text/plain stream_size 50110 Content-Encoding ISO-8859-1 stream_name Nortex Regional Transportation Coordination Plan.pdf.txt Content... Transportation Coordination December 1, 2006 Submitted to The Texas Department of Transportation Mission To provide reliable, quality, coordinated, public transportation. Texas State Planning Region 3 Page 1 Table of Contents Table...

  4. Method of doping organic semiconductors

    DOE Patents [OSTI]

    Kloc, Christian Leo (Constance, DE); Ramirez, Arthur Penn (Summit, NJ); So, Woo-Young (New Providence, NJ)

    2012-02-28

    A method includes the steps of forming a contiguous semiconducting region and heating the region. The semiconducting region includes polyaromatic molecules. The heating raises the semiconducting region to a temperature above room temperature. The heating is performed in the presence of a dopant gas and the absence of light to form a doped organic semiconducting region.

  5. Pilot evaluation of electricity-reliability and power-quality monitoring in California's Silicon Valley with the I-Grid(R) system

    E-Print Network [OSTI]

    Eto, Joseph; Divan, Deepak; Brumsickle, William

    2004-01-01

    affect the regional power grid. January 23, 2003, AirplaneParadigm in Distribution Grid Power Quality And Reliability5 3. Description of the I-Grid Power-Quality and Reliability

  6. FORMAL SEMANTICS AND VERIFICATION OF DYNAMIC RELIABILITY BLOCK DIAGRAMS FOR SYSTEM RELIABILITY MODELING

    E-Print Network [OSTI]

    Xu, Haiping

    that DRBD provides a powerful tool for system reliability modeling, and our proposed verification approachFORMAL SEMANTICS AND VERIFICATION OF DYNAMIC RELIABILITY BLOCK DIAGRAMS FOR SYSTEM RELIABILITY-scale computer-based systems. KEY WORDS Reliability modeling, dynamic reliability block diagrams (DRBD), Object

  7. Electric Transmission Network: A Multi-Region Analysis, The

    Reports and Publications (EIA)

    2000-01-01

    This paper examines the ability of the existing transmission network to respond efficiently to increased trade over four reliability regions in the northeastern United States.

  8. Arnold Schwarzenegger REAL-TIME GRID RELIABILITY

    E-Print Network [OSTI]

    Energy Research (PIER) California Energy Commission Beth Chambers Contract Manager Jamie Patterson (VSA) prototype to monitor system voltage conditions and provide real time dispatchers with reliabilityArnold Schwarzenegger Governor REAL-TIME GRID RELIABILITY MANAGEMENT California ISO Real

  9. Electric Power Reliability in Chemical Plants†

    E-Print Network [OSTI]

    Cross, M. B.

    1989-01-01

    at plants across the country? Has the quality and reliability of utility-generated power deteriorated over the past five or ten years? Or, has the perception of what constitutes reliable power changed with the advent, installation, and increasing usage...

  10. Sandia Energy - PV Reliability & Performance Model

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Model PV Reliability & Performance ModelTara Camacho-Lopez2015-06-01T20:13:00+00:00 This Web Demo model is a simplified "player" version of the Photovoltaic Reliability Performance...

  11. SELECTING TRAVEL RELIABILITY MEASURES David Schrank

    E-Print Network [OSTI]

    SELECTING TRAVEL RELIABILITY MEASURES by Tim Lomax David Schrank Shawn Turner Texas Transportation Administration provided technical resource staff persons who identified the need for a reliability measure, California Department of Transportation Tim Baker, Colorado Department of Transportation Gordon Morgan

  12. Method of doping organic semiconductors

    DOE Patents [OSTI]

    Kloc, Christian Leo (Constance, DE); Ramirez, Arthur Penn (Summit, NJ); So, Woo-Young (New Providence, NJ)

    2010-10-26

    An apparatus has a crystalline organic semiconducting region that includes polyaromatic molecules. A source electrode and a drain electrode of a field-effect transistor are both in contact with the crystalline organic semiconducting region. A gate electrode of the field-effect transistor is located to affect the conductivity of the crystalline organic semiconducting region between the source and drain electrodes. A dielectric layer of a first dielectric that is substantially impermeable to oxygen is in contact with the crystalline organic semiconducting region. The crystalline organic semiconducting region is located between the dielectric layer and a substrate. The gate electrode is located on the dielectric layer. A portion of the crystalline organic semiconducting region is in contact with a second dielectric via an opening in the dielectric layer. A physical interface is located between the second dielectric and the first dielectric.

  13. Reliability-based casing design

    SciTech Connect (OSTI)

    Maes, M.A. [Univ. of Calgary, Alberta (Canada). Civil Engineering Dept.; Gulati, K.C.; Johnson, R.C. [Mobil Research and Development Corp., Dallas, TX (United States); McKenna, D.L. [Mobil Producing Nigeria, Lagos (Nigeria); Brand, P.R.; Lewis, D.B. [Mobil E and P Technical Center, Dallas, TX (United States)

    1995-06-01

    The present paper describes the development of reliability-based design criteria for oil and/or gas well casing/tubing. The approach is based on the fundamental principles of limit state design. Limit states for tubulars are discussed and specific techniques for the stochastic modeling of loading and resistance variables are described. Zonation methods and calibration techniques are developed which are geared specifically to the characteristic tubular design for both hydrocarbon drilling and production applications. The application of quantitative risk analysis to the development of risk-consistent design criteria is shown to be a major and necessary step forward in achieving more economic tubular design.

  14. Sandia Energy - PV Systems Reliability

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II)Geothermal Energy &WaterNew CREWOnline AbstractsSystems Reliability

  15. LUNAR MASS SPECTROMETER RELIABILITY LOGIC DIAGRAM

    E-Print Network [OSTI]

    Rathbun, Julie A.

    point (A) to (F). The block diagram also defines the reliability functions for the purpose of FMEA 1

  16. Reliability Challenges for Solar Energy (Presentation)

    SciTech Connect (OSTI)

    Kurtz, S.

    2009-12-08

    Presentation that reviews reliability issues related to various types of photovoltaic tecnnologies, including crystalline silicon, thin films, and concentrating PV.

  17. Dispatcher Reliability Analysis : SPICA-RAIL Experiments

    E-Print Network [OSTI]

    Paris-Sud XI, Universitť de

    consider that humans are fully reliable. But experience shows that many accidents involve human failuresDispatcher Reliability Analysis : SPICA-RAIL Experiments Fabien Belmonte, Jean-Louis Boulanger of scenarios and evaluate the behaviour of human operators. A state of the art in human reliability is pre

  18. Observations of Diurnal to Weekly Variations of Monoterpene-Dominated Fluxes of Volatile Organic Compounds from Mediterranean Forests: Implications for Regional Modeling

    SciTech Connect (OSTI)

    Fares, Silvano; Schnitzhofer, Ralf; Xiaoyan, Jiang; Guenther, Alex B.; Hansel, Armin; Loreto, Francesco

    2013-09-04

    Most vascular plants species, especially trees, emit biogenic volatile organic compounds (BVOC). Global estimates of BVOC emissions from plants range from 1 to 1.5 Pg C yr?1.1 Mediterranean forest trees have been described as high BVOC emitters, with emission depending primarily on light and temperature, and therefore being promoted by the warm Mediterranean climate. In the presence of sufficient sunlight and nitrogen oxides (NOx), the oxidation of BVOCs can lead to the formation of tropospheric ozone, a greenhouse gas with detrimental effects on plant health, crop yields, and human health. BVOCs are also precursors for aerosol formation, accounting for a significant fraction of secondary organic aerosol (SOA) produced in the atmosphere. The presidential Estate of Castelporziano covers an area of about 6000 ha located 25 km SW from the center of Rome, Italy (Figure 1) and hosts representative forest ecosystems typical of Mediterranean areas: holm oak forests, pine forests, dune vegetation, mixed oak and pine forests. Between 1995 and 2011, three intensive field campaigns were carried out on Mediterranean-type ecosystems inside the Estate. These campaigns were aimed at measuring BVOC emissions and environmental parameters, to improve formulation of basal emission factors (BEFs), that is, standardized emissions at 30 įC and 1000 ?mol m?2s?1 of photosynthetic active radiation (PAR). BEFs are key input parameters of emission models. The first campaign in Castelporziano was a pioneering integrated study on biogenic emissions (1993? 19964). BVOC fluxes from different forest ecosystems were mainly investigated using plant- and leaf enclosures connected to adsorption tubes followed by GC?MS analysis in the laboratory. This allowed a first screening of Mediterranean species with respect to their BVOC emission potential, environmental control, and emission algorithms. In particular, deciduous oak species revealed high isoprene emissions (Quercus f rainetto, Quercus petrea, Quercus pubescens), while evergreen oaks emitted monoterpenes only, for example, Quercus ilex = holm oak. Differences in constitutive emission patterns discovered in Castelporziano supplied basic information to discriminate oak biodiversity in following studies.Ten years later, a second experimental campaign took place in spring and summer 2007 on a dune-shrubland experimental site. In this campaign, the use of a proton transfer reaction mass spectrometer (PTR-MS14) provided the fast BVOC observations necessary for quasi-real-time flux measurements using Disjunct Eddy Covariance. This allowed for the first time continuous measurements and BEFs calculation at canopy level. Finally, in September 2011 a third campaign was performed with the aim of further characterizing and improving estimates of BVOC fluxes from mixed Mediterranean forests dominated by a mixed holm oak and stone pine forest, using for the first time a proton transfer reaction?time-of-flight?mass spectrometer (PTR-TOF-MS). In contrast to the standard quadrupole PTR-MS, which can only measure one m/z ratio at a discrete time, thus being inadequate to quantify fluxes of more than a handful of compounds simultaneously, PTR-TOF-MS allowed simultaneous measurements (10 Hz) of fluxes of all BVOCs at the canopy level by Eddy Covariance.17?20, 50 In this work, we reviewed BEFs from previous campaigns in Castelporziano and calculated new BEFs from the campaign based on PTR-TOF-MS analysis. The new BEFs were used to parametrize the model of emissions of gases and aerosols from nature (MEGAN v2.11).

  19. RESEARCH ADMINISTRATION Professional Organizations

    E-Print Network [OSTI]

    Acton, Scott

    RESEARCH ADMINISTRATION Professional Organizations: Society of Research Administrators (SRA) International National Council of University Research Administrators (NCURA) National Council of University Research Administrators (NCURA) Region III Society of Clinical Research Associates (SOCRA) Central Virginia

  20. Achieving High Reliability Operations Through Multi-Program Integration

    SciTech Connect (OSTI)

    Holly M. Ashley; Ronald K. Farris; Robert E. Richards

    2009-04-01

    Over the last 20 years the Idaho National Laboratory (INL) has adopted a number of operations and safety-related programs which has each periodically taken its turn in the limelight. As new programs have come along there has been natural competition for resources, focus and commitment. In the last few years, the INL has made real progress in integrating all these programs and are starting to realize important synergies. Contributing to this integration are both collaborative individuals and an emerging shared vision and goal of the INL fully maturing in its high reliability operations. This goal is so powerful because the concept of high reliability operations (and the resulting organizations) is a masterful amalgam and orchestrator of the best of all the participating programs (i.e. conduct of operations, behavior based safety, human performance, voluntary protection, quality assurance, and integrated safety management). This paper is a brief recounting of the lessons learned, thus far, at the INL in bringing previously competing programs into harmony under the goal (umbrella) of seeking to perform regularly as a high reliability organization. In addition to a brief diagram-illustrated historical review, the authors will share the INLís primary successes (things already effectively stopped or started) and the gaps yet to be bridged.

  1. College of Electricity Delivery and Energy Reliability | Department...

    Energy Savers [EERE]

    Electricity Delivery and Energy Reliability College of Electricity Delivery and Energy Reliability College of Electricity Delivery and Energy Reliability Vision OE recognizes that...

  2. Microgrids and Heterogeneous Security, Quality, Reliability, and Availability

    E-Print Network [OSTI]

    Marnay, Chris

    2007-01-01

    quality, reliability, and availability,Ē IEEE Power & EnergyReliability, and Availability Chris Marnay EnvironmentalQuality, Reliability, and Availability C. Marnay Ernest

  3. Utility-scale grid-tied PV inverter reliability workshop summary report.

    SciTech Connect (OSTI)

    Granata, Jennifer E.; Quintana, Michael A.; Tasca, Coryne Adelle; Atcitty, Stanley

    2011-07-01

    A key to the long-term success of the photovoltaic (PV) industry is confidence in the reliability of PV systems. Inverters are the most commonly noted cause of PV system incidents triggered in the field. While not all of these incidents are reliability-related or even necessarily failures, they still result in a loss of generated power. With support from the U.S. Department of Energy's Solar Energy Technologies Program, Sandia National Laboratories organized a Utility-Scale Grid-Tied Inverter Reliability Workshop in Albuquerque, New Mexico, January 27-28, 2011. The workshop addressed the reliability of large (100-kilowatt+) grid-tied inverters and the implications when such inverters fail, evaluated inverter codes and standards, and provided discussion about opportunities to enhance inverter reliability. This report summarizes discussions and presentations from the workshop and identifies opportunities for future efforts.

  4. MEMS reliability in shock environments

    SciTech Connect (OSTI)

    TANNER,DANELLE M.; WALRAVEN,JEREMY A.; HELGESEN,KAREN SUE; IRWIN,LLOYD W.; BROWN,FREDERICK A.; SMITH,NORMAN F.; MASTERS,NATHAN

    2000-02-09

    In order to determine the susceptibility of the MEMS (MicroElectroMechanical Systems) devices to shock, tests were performed using haversine shock pulses with widths of 1 to 0.2 ms in the range from 500g to 40,000g. The authors chose a surface-micromachined microengine because it has all the components needed for evaluation: springs that flex, gears that are anchored, and clamps and spring stops to maintain alignment. The microengines, which were unpowered for the tests, performed quite well at most shock levels with a majority functioning after the impact. Debris from the die edges moved at levels greater than 4,000g causing shorts in the actuators and posing reliability concerns. The coupling agent used to prevent stiction in the MEMS release weakened the die-attach bond, which produced failures at 10,000g and above. At 20,000g the authors began to observe structural damage in some of the thin flexures and 2.5-micron diameter pin joints. The authors observed electrical failures caused by the movement of debris. Additionally, they observed a new failure mode where stationary comb fingers contact the ground plane resulting in electrical shorts. These new failure were observed in the control group indicating that they were not shock related.

  5. Evaluation of MHTGR fuel reliability

    SciTech Connect (OSTI)

    Wichner, R.P. [Oak Ridge National Lab., TN (United States); Barthold, W.P. [Barthold Associates, Inc., Knoxville, TN (United States)

    1992-07-01

    Modular High-Temperature Gas-Cooled Reactor (MHTGR) concepts that house the reactor vessel in a tight but unsealed reactor building place heightened importance on the reliability of the fuel particle coatings as fission product barriers. Though accident consequence analyses continue to show favorable results, the increased dependence on one type of barrier, in addition to a number of other factors, has caused the Nuclear Regulatory Commission (NRC) to consider conservative assumptions regarding fuel behavior. For this purpose, the concept termed ``weak fuel`` has been proposed on an interim basis. ``Weak fuel`` is a penalty imposed on consequence analyses whereby the fuel is assumed to respond less favorably to environmental conditions than predicted by behavioral models. The rationale for adopting this penalty, as well as conditions that would permit its reduction or elimination, are examined in this report. The evaluation includes an examination of possible fuel-manufacturing defects, quality-control procedures for defect detection, and the mechanisms by which fuel defects may lead to failure.

  6. Real Time Grid Reliability Management 2005

    E-Print Network [OSTI]

    Eto, Joe

    2008-01-01

    W.R. Schmus, D.C. Dawson, ďTransmission Voltage RecoveryEnhancing AC-DC Power System Transmission Reliability and

  7. Smart Grid Investments Improve Grid Reliability, Resilience,...

    Energy Savers [EERE]

    customers, and improve overall service reliability to reduce customer losses from power disruptions. This report presents findings on smart grid improvements in outage...

  8. Information Concerning Reliability Impacts under Various System...

    Broader source: Energy.gov (indexed) [DOE]

    of sentence redacted) In addition, there is a discussion concerning the impacts of demand side response in addressing this situation. Information Concerning Reliability...

  9. Comments of North American Electric Reliability Corporation ...

    Office of Environmental Management (EM)

    RFI. North American Electric Reliability Corporation (NERC) More Documents & Publications City Utilities of Springfield Missouri Comments on Smart Grid RFI: Addressing Policy and...

  10. Fundamental mechanisms of micromachine reliability

    SciTech Connect (OSTI)

    DE BOER,MAARTEN P.; SNIEGOWSKI,JEFFRY J.; KNAPP,JAMES A.; REDMOND,JAMES M.; MICHALSKE,TERRY A.; MAYER,THOMAS K.

    2000-01-01

    Due to extreme surface to volume ratios, adhesion and friction are critical properties for reliability of Microelectromechanical Systems (MEMS), but are not well understood. In this LDRD the authors established test structures, metrology and numerical modeling to conduct studies on adhesion and friction in MEMS. They then concentrated on measuring the effect of environment on MEMS adhesion. Polycrystalline silicon (polysilicon) is the primary material of interest in MEMS because of its integrated circuit process compatibility, low stress, high strength and conformal deposition nature. A plethora of useful micromachined device concepts have been demonstrated using Sandia National Laboratories' sophisticated in-house capabilities. One drawback to polysilicon is that in air the surface oxidizes, is high energy and is hydrophilic (i.e., it wets easily). This can lead to catastrophic failure because surface forces can cause MEMS parts that are brought into contact to adhere rather than perform their intended function. A fundamental concern is how environmental constituents such as water will affect adhesion energies in MEMS. The authors first demonstrated an accurate method to measure adhesion as reported in Chapter 1. In Chapter 2 through 5, they then studied the effect of water on adhesion depending on the surface condition (hydrophilic or hydrophobic). As described in Chapter 2, they find that adhesion energy of hydrophilic MEMS surfaces is high and increases exponentially with relative humidity (RH). Surface roughness is the controlling mechanism for this relationship. Adhesion can be reduced by several orders of magnitude by silane coupling agents applied via solution processing. They decrease the surface energy and render the surface hydrophobic (i.e. does not wet easily). However, only a molecular monolayer coats the surface. In Chapters 3-5 the authors map out the extent to which the monolayer reduces adhesion versus RH. They find that adhesion is independent of RH up to a threshold value, depending on the coating chemistry. The mechanism for the adhesion increase beyond this threshold value is that the coupling agent reconfigures from a surface to a bulk phase (Chapter 3). To investigate the details of how the adhesion increase occurs, the authors developed the mechanics for adhesion hysteresis measurements. These revealed that near-crack tip compression is the underlying cause of the adhesion increase (Chapter 4). A vacuum deposition chamber for silane coupling agent deposition was constructed. Results indicate that vapor deposited coatings are less susceptible to degradation at high RH (Chapter 5). To address issues relating to surfaces in relative motion, a new test structure to measure friction was developed. In contrast to other surface micromachined friction test structures, uniform apparent pressure is applied in the frictional contact zone (Chapter 6). The test structure will enable friction studies over a large pressure and dynamic range. In this LDRD project, the authors established an infrastructure for MEMS adhesion and friction metrology. They then characterized in detail the performance of hydrophilic and hydrophobic films under humid conditions, and determined mechanisms which limit this performance. These studies contribute to a fundamental understanding for MEMS reliability design rules. They also provide valuable data for MEMS packaging requirements.

  11. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    x America s Energy Future x America s Energy Future Maryland http www x25 org A View of the Rockies A View of the Rockies http www aviewoftherockies com ACORE ACORE PO Box...

  12. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo, Maryland:NPIProtectio Program | OpenWisconsin: Energy Resources JumpOrfordville,fuelsAWEA

  13. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo, Maryland:NPIProtectio Program | OpenWisconsin: Energy Resources

  14. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg, Oregon:OGEProjects/DefinitionsOrchid Bioenergy

  15. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg, Oregon:OGEProjects/DefinitionsOrchid BioenergyColorado

  16. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg, Oregon:OGEProjects/DefinitionsOrchid

  17. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg, Oregon:OGEProjects/DefinitionsOrchidx America s Energy Future

  18. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg, Oregon:OGEProjects/DefinitionsOrchidx America s Energy

  19. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg, Oregon:OGEProjects/DefinitionsOrchidx America s

  20. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg, Oregon:OGEProjects/DefinitionsOrchidx America sAssociation

  1. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceII JumpQuarterly Smart Grid DataInformation LandWindsourceFoundation American

  2. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceII JumpQuarterly Smart Grid DataInformation LandWindsourceFoundation

  3. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceII JumpQuarterly Smart Grid DataInformation LandWindsourceFoundationE Street NW

  4. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceII JumpQuarterly Smart Grid DataInformation LandWindsourceFoundationE Street

  5. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceII JumpQuarterly Smart Grid DataInformation LandWindsourceFoundationE

  6. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceII JumpQuarterly Smart Grid DataInformation LandWindsourceFoundationECalifornia

  7. Organization Organization Address Place Zip Notes Website Region

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceII JumpQuarterly Smart Grid DataInformation

  8. Software Reliability Cases: The Bridge Between Hardware, Software and System Safety and Reliability

    SciTech Connect (OSTI)

    Herrmann, D.S.; Peercy, D.E.

    1999-01-08

    High integrity/high consequence systems must be safe and reliable; hence it is only logical that both software safety and software reliability cases should be developed. Risk assessments in safety cases evaluate the severity of the consequences of a hazard and the likelihood of it occurring. The likelihood is directly related to system and software reliability predictions. Software reliability cases, as promoted by SAE JA 1002 and 1003, provide a practical approach to bridge the gap between hardware reliability, software reliability, and system safety and reliability by using a common methodology and information structure. They also facilitate early insight into whether or not a project is on track for meeting stated safety and reliability goals, while facilitating an informed assessment by regulatory and/or contractual authorities.

  9. Advances in Safety, Reliability and Risk Management -Proceedings of the European Safety and Reliability Conference, ESREL 2011 -European Safety and Reliability Conference: Advances in Safety, Reliability and

    E-Print Network [OSTI]

    Paris-Sud XI, Universitť de

    Advances in Safety, Reliability and Risk Management - Proceedings of the European Safety, Reliability and Risk Management, ESREL 2011, Troyes : France (2011) In France, more than 99% of failed is global risk management. This allows analysis of the major risks faced by the busi- ness (loss

  10. Reliability Meets Big Data: Opportunities and Challenges

    E-Print Network [OSTI]

    McCalley, James D.

    Reliability Meets Big Data: Opportunities and Challenges William Q. Meeker Department of Statistics maintenance operations. 1.2 Examples of systems providing big data Some examples of particular systems 1, 2013 Abstract Reliability field data such as that obtained from warranty claims and maintenance

  11. RELIABILITY-BASED CASTING PROCESS DESIGN OPTIMIZATION

    E-Print Network [OSTI]

    Beckermann, Christoph

    , shrinkage porosity in the casting. Despite the power and promise of these developments in casting processRELIABILITY-BASED CASTING PROCESS DESIGN OPTIMIZATION Richard Hardin1 , K.K. Choi1 , and Christoph 52242-1527 Keywords: Casting Process Design, Optimization, Reliability-Based Design Optimization

  12. Reliable fuel source | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II) by Carbon-RichProtonAbout UsRegional companiesReliability

  13. Real Time Grid Reliability Management 2005

    E-Print Network [OSTI]

    Eto, Joe

    2008-01-01

    10 Figure 2-4. Organization chart for the PlanningTask Force Figure 2-4. Organization chart for the Planning

  14. Reliability of Coupled Oscillators II: Larger Networks

    E-Print Network [OSTI]

    Kevin K. Lin; Eric Shea-Brown; Lai-Sang Young

    2007-08-23

    We study the reliability of phase oscillator networks in response to fluctuating inputs. Reliability means that an input elicits essentially identical responses upon repeated presentations, regardless of the network's initial condition. In this paper, we extend previous results on two-cell networks to larger systems. The first issue that arises is chaos in the absence of inputs, which we demonstrate and interpret in terms of reliability. We give a mathematical analysis of networks that can be decomposed into modules connected by an acyclic graph. For this class of networks, we show how to localize the source of unreliability, and address questions concerning downstream propagation of unreliability once it is produced.

  15. MEMS reliability: The challenge and the promise

    SciTech Connect (OSTI)

    Miller, W.M.; Tanner, D.M.; Miller, S.L.; Peterson, K.A.

    1998-05-01

    MicroElectroMechanical Systems (MEMS) that think, sense, act and communicate will open up a broad new array of cost effective solutions only if they prove to be sufficiently reliable. A valid reliability assessment of MEMS has three prerequisites: (1) statistical significance; (2) a technique for accelerating fundamental failure mechanisms, and (3) valid physical models to allow prediction of failures during actual use. These already exist for the microelectronics portion of such integrated systems. The challenge lies in the less well understood micromachine portions and its synergistic effects with microelectronics. This paper presents a methodology addressing these prerequisites and a description of the underlying physics of reliability for micromachines.

  16. PV Module Reliability Research (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2013-06-01

    This National Center for Photovoltaics sheet describes the capabilities of its PV module reliability research. The scope and core competencies and capabilities are discussed and recent publications are listed.

  17. RELIABILITY PLANNING IN DISTRIBUTED ELECTRIC ENERGY SYSTEMS

    E-Print Network [OSTI]

    Kahn, E.

    2011-01-01

    Edward, Reliability of Wind Power from Dispersed Sites:The same is true for wind power. This Even over hundreds ofof (11) also shows how wind power output distributi.on

  18. Reliability of copper interconnects in integrated circuits

    E-Print Network [OSTI]

    Choi, Zung-Sun

    2007-01-01

    As dimensions shrink and current densities increase, the reliability of metal interconnects becomes a serious concern. In copper interconnects, the dominant diffusion path is along the interface between the copper and the ...

  19. Reliable Distributed Computing for Decision Support Systems

    E-Print Network [OSTI]

    Bargiela, Andrzej

    of pipes and network nodes spread over a large geographical area, calls for a control of computational system it is serv- icing. Addressing the reliability issues of dis- tributed systems involves tackling

  20. Reliability Issues for Photovoltaic Modules (Presentation)

    SciTech Connect (OSTI)

    Kurtz, S.

    2009-10-01

    Si modules good in field; new designs need reliability testing. CdTe & CIGS modules sensitive to moisture; carefully seal. CPV in product development stage; benefits from expertise in other industries.

  1. Reliability Challenges for Solar Energy (Presentation)

    SciTech Connect (OSTI)

    Kurtz, S.

    2009-04-27

    PV industry can benefit from reliability testing experience of microelectronics industry . Si modules perform well in field; CdTe/CIGS must be sealed to moisture; CPV in product development stage.

  2. Demand Response For Power System Reliability: FAQ

    SciTech Connect (OSTI)

    Kirby, Brendan J [ORNL

    2006-12-01

    Demand response is the most underutilized power system reliability resource in North America. Technological advances now make it possible to tap this resource to both reduce costs and improve. Misconceptions concerning response capabilities tend to force loads to provide responses that they are less able to provide and often prohibit them from providing the most valuable reliability services. Fortunately this is beginning to change with some ISOs making more extensive use of load response. This report is structured as a series of short questions and answers that address load response capabilities and power system reliability needs. Its objective is to further the use of responsive load as a bulk power system reliability resource in providing the fastest and most valuable ancillary services.

  3. Gearbox Reliability Collaborative (GRC) Description and Loading

    SciTech Connect (OSTI)

    Oyague, F.

    2011-11-01

    This document describes simulated turbine load cases in accordance to the IEC 61400-1 Ed.3 standard, which is representative of the typical wind turbine design process. The information presented herein is intended to provide a broad understanding of the gearbox reliability collaborative 750kW drivetrain and turbine configuration. In addition, fatigue and ultimate strength drivetrain loads resulting from simulations are presented. This information provides the bases for the analytical work of the gearbox reliability collaborative effort.

  4. System Reliability for LED-Based Products

    SciTech Connect (OSTI)

    Davis, J Lynn; Mills, Karmann; Lamvik, Michael; Yaga, Robert; Shepherd, Sarah D; Bittle, James; Baldasaro, Nick; Solano, Eric; Bobashev, Georgiy; Johnson, Cortina; Evans, Amy

    2014-04-07

    Results from accelerated life tests (ALT) on mass-produced commercially available 6Ē downlights are reported along with results from commercial LEDs. The luminaires capture many of the design features found in modern luminaires. In general, a systems perspective is required to understand the reliability of these devices since LED failure is rare. In contrast, components such as drivers, lenses, and reflector are more likely to impact luminaire reliability than LEDs.

  5. Dormant storage reliability assessments-data based

    SciTech Connect (OSTI)

    Merren, G.T.

    1981-01-01

    A relatively large amount of data pertaining to the performance of certain electronic parts after long periods of dormant storage has been collected and analyzed by the Reliability Department of Sandia National Laboratories. The failure models used by Sandia are presented and reliability assessments for selected electronic parts derived from these models and the measured performance data are provided. These data based assessments are compared to similar assessments derived from handbook calculations using the general data and models provided in the handbooks.

  6. WEBCASRE: A WEBBASED TOOL FOR SOFTWARE RELIABILITY MODELING

    E-Print Network [OSTI]

    Lyu, Michael R.

    of overall system reliability. This trend makes the estimation of software reliability more and more critical to most large¬≠scale projects in their reliability engineering aspects. Traditionally, software reliabilityWEB¬≠CASRE: A WEB¬≠BASED TOOL FOR SOFTWARE RELIABILITY MODELING Michael R. Lyu \\Lambda Jň?urgen Sch

  7. Assessing the Reliability of a Human Estimator Gary D. Boetticher, Nazim Lokhandwala

    E-Print Network [OSTI]

    Boetticher, Gary D.

    than humans make [2]. Algorithmic-based estimation approaches are based on human subjectivity. The post-architecture from estimating models to current projects and organization environments in order to achieveAssessing the Reliability of a Human Estimator Gary D. Boetticher, Nazim Lokhandwala University

  8. Measuring eating disorder attitudes and behaviors: a reliability generalization study†

    E-Print Network [OSTI]

    Pearson, Crystal Anne

    2009-05-15

    I used reliability generalization procedures to determine the mean score reliability of the Eating Disorder Inventory (EDI), the Eating Attitudes Test (EAT), and the Bulimia Test (BULIT). Reliability generalization is a ...

  9. Empirical Measurements of Travelers' Value of Travel Time Reliability

    E-Print Network [OSTI]

    Danda, Santosh Rao

    2014-08-12

    empirical data to take an initial step toward understanding the importance of travel time reliability. Katy Freeway travelers face a daily choice between reliable tolled lanes and less reliable but untolled lanes. An extensive dataset of Katy Freeway travel...

  10. Owner/Operator Perspective on Reliability Customer Needs and...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SERVICES AS RELIABLE AS THE SUN OwnerOperator Perspective on Reliability Customer Needs and Field Data Sandia National Laboratories Utility-Scale Grid-Tied PV Inverter Reliability...

  11. FOOD SERVICE Professional Organizations

    E-Print Network [OSTI]

    Acton, Scott

    FOOD SERVICE Professional Organizations: National Association of College and University Food National Association of College and University Food Services (NACUFS) conference NACUFS Mid-Atlantic Region of Colleges and University Food Services e-newsletter Social Media: National Association of College

  12. The Business Case for Fuel Cells 2013: Reliability, Resiliency...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The Business Case for Fuel Cells 2013: Reliability, Resiliency & Savings The Business Case for Fuel Cells 2013: Reliability, Resiliency & Savings This report, compiled by Fuel...

  13. The Business Case for Fuel Cells 2013: Reliability, Resiliency...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3: Reliability, Resiliency & Savings The Business Case for Fuel Cells 2013: Reliability, Resiliency & Savings This report, compiled by Fuel Cells 2000 with support from the Fuel...

  14. System Reliability Model for Solid-State Lighting Luminaires...

    Energy Savers [EERE]

    System Reliability Model for Solid-State Lighting Luminaires System Reliability Model for Solid-State Lighting Luminaires Lead Performer: RTI International - Research Triangle...

  15. Reliability of islanded microgrids with stochastic generation and prioritized load

    E-Print Network [OSTI]

    Marden, Mirjana Milosevic

    The potential to improve distribution system reliability is a primary motivation behind the development and deployment of microgrids. Previous studies have illustrated substantial reliability benefits of dispatchable ...

  16. Reliable estimation of biochemical parameters from C3 leafphotosynthe...

    Office of Scientific and Technical Information (OSTI)

    Reliable estimation of biochemical parameters from C3 leaf photosynthesis-intercellular carbon dioxide response curves Citation Details In-Document Search Title: Reliable...

  17. Characterizing wind power resource reliability in southern Africa...

    Office of Scientific and Technical Information (OSTI)

    DOE PAGES Search Results Published Article: Characterizing wind power resource reliability in southern Africa Title: Characterizing wind power resource reliability in southern...

  18. Washington DC Reliability Requirements and the Need to Operate...

    Energy Savers [EERE]

    DC Reliability Requirements and the Need to Operate Mirant's Potomac River Generation Station to Support Local Area Reliability (Oak Ridge National Laboratory 2005)...

  19. Effect of Jatropha based Biodiesel, on Engine Hardware Reliability...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Jatropha based Biodiesel, on Engine Hardware Reliability, Emission and Performance Effect of Jatropha based Biodiesel, on Engine Hardware Reliability, Emission and Performance...

  20. CHP SYSTEM AT FOOD PROCESSING PLANT INCREASES RELIABILITY AND...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CHP SYSTEM AT FOOD PROCESSING PLANT INCREASES RELIABILITY AND REDUCES EMISSIONS - CASE STUDY, 2015 CHP SYSTEM AT FOOD PROCESSING PLANT INCREASES RELIABILITY AND REDUCES EMISSIONS -...

  1. Data Center Efficiency and IT Equipment Reliability at Wider...

    Energy Savers [EERE]

    Data Center Efficiency and IT Equipment Reliability at Wider Operating Temperature and Humidity Ranges Data Center Efficiency and IT Equipment Reliability at Wider Operating...

  2. Office of Electricity Delivery and Energy Reliability Cyber Security...

    Energy Savers [EERE]

    Office of Electricity Delivery and Energy Reliability Cyber Security Project Selections Office of Electricity Delivery and Energy Reliability Cyber Security Project Selections On...

  3. 2013 Reliability & Markets Peer Review | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the links. The agenda and list of presentations are included below. The Reliability and Markets activity of the Transmission Reliability program researches, develops, and...

  4. Thermal Stress and Reliability for Advanced Power Electronics...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Performance and Reliability of Bonded Interfaces Physics of Failure of Electrical Interconnects Thermal Stress and Reliability for Advanced Power Electronics and Electric Machines...

  5. Addressing mechanical reliability issues in Sandia MEMS devices...

    Office of Scientific and Technical Information (OSTI)

    Addressing mechanical reliability issues in Sandia MEMS devices. Citation Details In-Document Search Title: Addressing mechanical reliability issues in Sandia MEMS devices. No...

  6. Office of Electricity Delivery & Energy Reliability FY 2012 Budget...

    Energy Savers [EERE]

    Office of Electricity Delivery & Energy Reliability FY 2012 Budget Request Presentation Office of Electricity Delivery & Energy Reliability FY 2012 Budget Request Presentation...

  7. PV Performance and Reliability Validation Capabilities at Sandia...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PV Performance and Reliability Validation Capabilities at Sandia National Laboratories PV Performance and Reliability Validation Capabilities at Sandia National Laboratories This...

  8. ASCE Specialty Conference on Probabilistic Mechanics and Structural Reliability ESTIMATING STRUCTURAL RELIABILITY UNDER HURRICANE WIND HAZARD

    E-Print Network [OSTI]

    Balaji, Rajagopalan

    STRUCTURAL RELIABILITY UNDER HURRICANE WIND HAZARD: APPLICATIONS TO WOOD STRUCTURES Balaji Rajagopalan.frangopol@colorado.edu Abstract A stochastic nonparametric framework to estimate structural reliability under hurricane wind Natural hazards in general and hurricanes in particular, lead to loss of life and tremendous property

  9. Technique for Measuring Hybrid Electronic Component Reliability

    SciTech Connect (OSTI)

    Green, C.C.; Hernandez, C.L.; Hosking, F.M.; Robinson, D.; Rutherford, B.; Uribe, F.

    1999-01-01

    Materials compatibility studies of aged, engineered materials and hardware are critical to understanding and predicting component reliability, particularly for systems with extended stockpile life requirements. Nondestructive testing capabilities for component reliability would significantly enhance lifetime predictions. For example, if the detection of crack propagation through a solder joint can be demonstrated, this technique could be used to develop baseline information to statistically determine solder joint lifelengths. This report will investigate high frequency signal response techniques for nondestructively evaluating the electrical behavior of thick film hybrid transmission lines.

  10. Gearbox Reliability Collaborative Update: A Brief (Presentation)

    SciTech Connect (OSTI)

    Sheng, S.; Keller, J.; McDade, M.

    2012-01-01

    This presentation is an update on the Gearbox Reliability Collaborative (GRC) for the AWEA Wind Project Operations, Maintenance & Reliability Seminar. GRC accomplishments are: (1) Failure database software deployed - partners see business value for themselves and customers; (2) Designed, built, instrumented, and tested two gearboxes - (a) Generated unprecedented public domain test data from both field testing and dynamometer testing, (b) Different responses from 'identical' gearboxes, (c) Demonstrated importance of non-torque loading and modeling approach; and (3) Active collaborative, with wide industry support, leveraging DOE funding - Modeling round robin and Condition Monitoring round robin.

  11. Doctoral Defense "Structural reliability assessment under fire"

    E-Print Network [OSTI]

    Kamat, Vineet R.

    Doctoral Defense "Structural reliability assessment under fire" Qianru Guo Date: December 11, 2014 Engineering Structural safety under fire has received significant attention in recent years. Current approaches to structural fire design are based on prescriptive codes that emphasize insulation of steel

  12. The challenge of reliability in MEMS commercialization

    SciTech Connect (OSTI)

    Miller, W.M.; Tanner, D.M.; Miller, S.L.

    1998-09-01

    MicroElectroMechanical Systems (MEMS) that think, sense, act and communicate will open up a broad new array of cost-effective solutions only if MEMS is demonstrated to be sufficiently reliable. This could prove to be a major challenge if it is not addressed concurrently with technology development. There are three requirements for a valid assessment of reliability: statistical significance, identification of fundamental failure mechanisms and development of techniques for accelerating them, and valid physical models to allow prediction of failures during actual use. While these already exist for the microelectronics portion of such integrated systems, the real challenge lies in the less well-understood micromachine portions and its synergistic effects with microelectronics. This requires the elicitation of a methodology focused on MEMS reliability, which the authors discuss. A new testing and analysis infrastructure must also be developed to meet the needs of this methodology. They describe their implementation of this infrastructure and its success in addressing the three requirements for a valid reliability assessment.

  13. Reliability based casting process design optimisation

    E-Print Network [OSTI]

    Beckermann, Christoph

    , which is typically defined as an absence of, or low level of, shrinkage porosity in the casting. DespiteReliability based casting process design optimisation R. A. Hardin, K. K. Choi, N. J. Gaul and C and physical uncertainties in the casting process. In the present research, casting simulation is integrated

  14. Wind Energy Facility Reliability and Maintenance

    E-Print Network [OSTI]

    Ding, Yu

    from 18 GW to 152 GW over the past decade. According to the north American electric reliability constitute a substantial portion of the total costs of wind power production [2≠4]. Field data from Germany to a few weeks. Overall, O&M costs account for 20-47.5% of the wholesale market price [4]. Considering

  15. Organization of the class I region of the bovine major histocompatibility complex (BoLA) and the characterization of a class I frameshift deletion (BoLA-Adel) prevalent in feral bovids†

    E-Print Network [OSTI]

    Ramlachan, Nicole

    2006-04-12

    region (Amadou et al. 2003; Hurt et al. 2004). The class I region also contains families of loci involved in DNA repair and cell growth like TFIIH (also called GTF2H4, transcription factor II H polypeptide 4), DDR1 (discoidin domain receptor family...

  16. Fermilab | About | Organization | Fermilab Organization | Explanation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Symbols Line Organization: sectors, divisions, sections Line Organization Matrix Organization: centers, projects and programs utilizing resources spanning the entire...

  17. Scoping study on trends in the economic value of electricity reliability to the U.S. economy

    SciTech Connect (OSTI)

    Eto, Joseph; Koomey, Jonathan; Lehman, Bryan; Martin, Nathan; Mills, Evan; Webber, Carrie; Worrell, Ernst

    2001-06-01

    During the past three years, working with more than 150 organizations representing public and private stakeholders, EPRI has developed the Electricity Technology Roadmap. The Roadmap identifies several major strategic challenges that must be successfully addressed to ensure a sustainable future in which electricity continues to play an important role in economic growth. Articulation of these anticipated trends and challenges requires a detailed understanding of the role and importance of reliable electricity in different sectors of the economy. This report is intended to contribute to that understanding by analyzing key aspects of trends in the economic value of electricity reliability in the U.S. economy. We first present a review of recent literature on electricity reliability costs. Next, we describe three distinct end-use approaches for tracking trends in reliability needs: (1) an analysis of the electricity-use requirements of office equipment in different commercial sectors; (2) an examination of the use of aggregate statistical indicators of industrial electricity use and economic activity to identify high reliability-requirement customer market segments; and (3) a case study of cleanrooms, which is a cross-cutting market segment known to have high reliability requirements. Finally, we present insurance industry perspectives on electricity reliability as an example of a financial tool for addressing customers' reliability needs.

  18. Human Reliability Analysis for Design: Using Reliability Methods for Human Factors Issues

    SciTech Connect (OSTI)

    Ronald Laurids Boring

    2010-11-01

    This paper reviews the application of human reliability analysis methods to human factors design issues. An application framework is sketched in which aspects of modeling typically found in human reliability analysis are used in a complementary fashion to the existing human factors phases of design and testing. The paper provides best achievable practices for design, testing, and modeling. Such best achievable practices may be used to evaluate and human system interface in the context of design safety certifications.

  19. Electronic logic for enhanced switch reliability

    DOE Patents [OSTI]

    Cooper, J.A.

    1984-01-20

    A logic circuit is used to enhance redundant switch reliability. Two or more switches are monitored for logical high or low output. The output for the logic circuit produces a redundant and fail-safe representation of the switch outputs. When both switch outputs are high, the output is high. Similarly, when both switch outputs are low, the logic circuit's output is low. When the output states of the two switches do not agree, the circuit resolves the conflict by memorizing the last output state which both switches were simultaneously in and produces the logical complement of this output state. Thus, the logic circuit of the present invention allows the redundant switches to be treated as if they were in parallel when the switches are open and as if they were in series when the switches are closed. A failsafe system having maximum reliability is thereby produced.

  20. Sample sizes for confidence limits for reliability.

    SciTech Connect (OSTI)

    Darby, John L.

    2010-02-01

    We recently performed an evaluation of the implications of a reduced stockpile of nuclear weapons for surveillance to support estimates of reliability. We found that one technique developed at Sandia National Laboratories (SNL) under-estimates the required sample size for systems-level testing. For a large population the discrepancy is not important, but for a small population it is important. We found that another technique used by SNL provides the correct required sample size. For systems-level testing of nuclear weapons, samples are selected without replacement, and the hypergeometric probability distribution applies. Both of the SNL techniques focus on samples without defects from sampling without replacement. We generalized the second SNL technique to cases with defects in the sample. We created a computer program in Mathematica to automate the calculation of confidence for reliability. We also evaluated sampling with replacement where the binomial probability distribution applies.

  1. Reliability Estimation for Double Containment Piping

    SciTech Connect (OSTI)

    L. Cadwallader; T. Pinna

    2012-08-01

    Double walled or double containment piping is considered for use in the ITER international project and other next-generation fusion device designs to provide an extra barrier for tritium gas and other radioactive materials. The extra barrier improves confinement of these materials and enhances safety of the facility. This paper describes some of the design challenges in designing double containment piping systems. There is also a brief review of a few operating experiences of double walled piping used with hazardous chemicals in different industries. This paper recommends approaches for the reliability analyst to use to quantify leakage from a double containment piping system in conceptual and more advanced designs. The paper also cites quantitative data that can be used to support such reliability analyses.

  2. Reliability assessment of underground shaft closure

    SciTech Connect (OSTI)

    Fossum, A.F.

    1994-12-31

    The intent of the WIPP, being constructed in the bedded geologic salt deposits of Southeastern New Mexico, is to provide the technological basis for the safe disposal of radioactive Transuranic (TRU) wastes generated by the defense programs of the United States. In determining this technological basis, advanced reliability and structural analysis techniques are used to determine the probability of time-to-closure of a hypothetical underground shaft located in an argillaceous salt formation and filled with compacted crushed salt. Before being filled with crushed salt for sealing, the shaft provides access to an underground facility. Reliable closure of the shaft depends upon the sealing of the shaft through creep closure and recompaction of crushed backfill. Appropriate methods are demonstrated to calculate cumulative distribution functions of the closure based on laboratory determined random variable uncertainty in salt creep properties.

  3. Reliability Considerations from Integration of Smart Grid

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on DeliciousMathematicsEnergyInterested PartiesBuildingBudgetFinancialReliability Considerations from the Integration

  4. Reliability of natural gas cogeneration systems

    SciTech Connect (OSTI)

    1995-12-01

    Cogeneration systems fueled by natural gas exceed the reliability of most central station power generating units, according to a study conducted by RINC Corporation for Gas Research Institute (GRI). In the study, researchers obtained operating data from 122 natural gas cogeneration units nationwide representing 2,200 megawatts (MW) of capacity and nearly 2 million hours of operating time at 37 facilities. Units were grouped into categories reflecting size (from 60 kilowatts to 100 MW), type of system (gas engine or gas turbine technology), use of emission controls, and type of thermal application. Various types and sizes of gas systems reported average availability factors ranging from 90.0 to 95.8 versus a weighted average of 85.9 percent for fossil-fuel steam, nuclear, and gas-turbine-based central station power generating units. Comparisons are based on study data and data reported by the North American Electric Reliability Council for utility power plants. Gas cogeneration can improve utility operations because as a group the relatively small, dispersed cogeneration units are more reliable than one or more large central station units of similar capacity.

  5. Statistical model selection for better prediction and discovering science mechanisms that affect reliability

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Anderson-Cook, Christine M.; Morzinski, Jerome; Blecker, Kenneth D.

    2015-08-19

    Understanding the impact of production, environmental exposure and age characteristics on the reliability of a population is frequently based on underlying science and empirical assessment. When there is incomplete science to prescribe which inputs should be included in a model of reliability to predict future trends, statistical model/variable selection techniques can be leveraged on a stockpile or population of units to improve reliability predictions as well as suggest new mechanisms affecting reliability to explore. We describe a five-step process for exploring relationships between available summaries of age, usage and environmental exposure and reliability. The process involves first identifying potential candidatemore†Ľinputs, then second organizing data for the analysis. Third, a variety of models with different combinations of the inputs are estimated, and fourth, flexible metrics are used to compare them. As a result, plots of the predicted relationships are examined to distill leading model contenders into a prioritized list for subject matter experts to understand and compare. The complexity of the model, quality of prediction and cost of future data collection are all factors to be considered by the subject matter experts when selecting a final model.ę†less

  6. Northwest Regional Technology Center, April 2013 Page 1 of 2 Around The Region In Homeland Security

    E-Print Network [OSTI]

    a venue for information sharing and education about cybersecurity concerns, advancements and resources Office of Electricity Delivery & Energy Reliability ∑ Samara Moore, National Security Staff; Director is National 9-1-1 Education Month, and public organizations are working to educate the community about

  7. Regional Purchasing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMassR&D100 Winners * ImpactsandRegarding ConfinementRegional Partnerships

  8. Organizing Committee

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEYI/O Streams for Large-scaleOrganizationAboutOrganizingOrganizing

  9. Continuous Reliability Enhancement for Wind (CREW) database : wind plant reliability benchmark.

    SciTech Connect (OSTI)

    Hines, Valerie Ann-Peters; Ogilvie, Alistair B.; Bond, Cody R.

    2013-09-01

    To benchmark the current U.S. wind turbine fleet reliability performance and identify the major contributors to component-level failures and other downtime events, the Department of Energy funded the development of the Continuous Reliability Enhancement for Wind (CREW) database by Sandia National Laboratories. This report is the third annual Wind Plant Reliability Benchmark, to publically report on CREW findings for the wind industry. The CREW database uses both high resolution Supervisory Control and Data Acquisition (SCADA) data from operating plants and Strategic Power Systems' ORAPWind%C2%AE (Operational Reliability Analysis Program for Wind) data, which consist of downtime and reserve event records and daily summaries of various time categories for each turbine. Together, these data are used as inputs into CREW's reliability modeling. The results presented here include: the primary CREW Benchmark statistics (operational availability, utilization, capacity factor, mean time between events, and mean downtime); time accounting from an availability perspective; time accounting in terms of the combination of wind speed and generation levels; power curve analysis; and top system and component contributors to unavailability.

  10. High reliability performance in Amgen Engineering

    E-Print Network [OSTI]

    Bolgren, Daniel (Daniel Reade)

    2012-01-01

    Amgen is in the midst of a transformative initiative to become operationally more efficient. For Amgen Engineering, this initiative has prompted a reevaluation of the entire organization and brought to light the need to ...

  11. Organic Superconductors

    SciTech Connect (OSTI)

    Charles Mielke

    2009-02-27

    Intense magnetic fields are an essential tool for understanding layered superconductors. Fundamental electronic properties of organic superconductors are revealed in intense (60 tesla) magnetic fields. Properties such as the topology of the Fermi surface and the nature of the superconducting order parameter are revealed. With modest maximum critical temperatures~13K the charge transfer salt organic superconductors prove to be incredibly valuable materials as their electronically clean nature and layered (highly anisotropic) structures yield insights to the high temperature superconductors. Observation of de Haas-van Alphen and Shubnikov-de Haas quantum oscillatory phenomena, magnetic field induced superconductivity and re-entrant superconductivity are some of the physical phenomena observed in the charge transfer organic superconductors. In this talk, I will discuss the nature of organic superconductors and give an overview of the generation of intense magnetic fields; from the 60 tesla millisecond duration to the extreme 1000 tesla microsecond pulsed magnetic fields.

  12. Energy Storage: The Key to a Reliable, Clean Electricity Supply...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Storage: The Key to a Reliable, Clean Electricity Supply Energy Storage: The Key to a Reliable, Clean Electricity Supply February 22, 2012 - 4:52pm Addthis Improved energy...

  13. Case Study: Fuel Cells Increase Reliability at First National...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Increase Reliability at First National Bank of Omaha Case Study: Fuel Cells Increase Reliability at First National Bank of Omaha First National Bank of Omaha installed a fuel cell...

  14. Final report on reliability and lifetime prediction.

    SciTech Connect (OSTI)

    Gillen, Kenneth Todd; Wise, Jonathan; Jones, Gary D.; Causa, Al G.; Terrill, Edward R.; Borowczak, Marc

    2012-12-01

    This document highlights the important results obtained from the subtask of the Goodyear CRADA devoted to better understanding reliability of tires and to developing better lifetime prediction methods. The overall objective was to establish the chemical and physical basis for the degradation of tires using standard as well as unique models and experimental techniques. Of particular interest was the potential application of our unique modulus profiling apparatus for assessing tire properties and for following tire degradation. During the course of this complex investigation, extensive relevant information was generated, including experimental results, data analyses and development of models and instruments. Detailed descriptions of the findings are included in this report.

  15. Reliability and Functional Availability of HVAC Systems†

    E-Print Network [OSTI]

    Myrefelt, S.

    2004-01-01

    the probability that a component or a system works when no maintenance is made. A system with a high reliability thus has minimal maintenance requirements; it is a robust system. The decision capability is used to assess the organisation?s capacity to start... the system is in operation in relation to intended operating time. It mainly shows the technical capability to keep on operating while maintenance is being carried out. Systems that must be taken out of operation for longer repair works have a lower level...

  16. Sandia Energy - Materials, Reliability, & Standards

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II)Geothermal Energy &Water Power& SF-BREEZEMaterials, Reliability,

  17. Human Reliability Program (HRP) - HPMC Occupational Health Services

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EpidemiologyHealth Data Analysis Human Reliability Program (HRP) Industrial Rehabilitation & Ergonomics Infection Control & Immunizations Influenza Immunization Program...

  18. Thermal Stress and Reliability for Advanced Power Electronics...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    & Publications Thermal Stress and Reliability for Advanced Power Electronics and Electric Machines Power Electronic Thermal System Performance and Integration Thermal...

  19. Competition and Reliability in North American Electricity Markets...

    Energy Savers [EERE]

    Publications The Relationship between Competitive Power Markets and Grid Reliability. Blackout 2003: Electric System Working Group Technical Conference - Comments and...

  20. REGION TRACKING WITH NARROW PERCEPTION OF BACKGROUND Julien Mille

    E-Print Network [OSTI]

    Mille, Julien

    address the problem of object tracking within image se- quences through region-based energy minimization. A com- mon underlying assumption in region tracking is that color statistics can be confidently the estima- tion of reliable color statistics for object/background discrim- ination. To overcome

  1. Reliable and Energy Efficient Transport Layer for Sensor Networks

    E-Print Network [OSTI]

    Valaee, Shahrokh

    Reliable and Energy Efficient Transport Layer for Sensor Networks Petar Djukic and Shahrokh Valaee Diversity Coded Directed Diffusion (DCDD), a reliable and energy efficient transport protocol for sensor-to-end reliability, as well as the effect of DCDD on energy consumption in the network. Our simulations show

  2. Reliable Provisioning of Data-Centric and Event-Based

    E-Print Network [OSTI]

    Dustdar, Schahram

    Reliable Provisioning of Data-Centric and Event-Based Applications in the Cloud DISSERTATION zur A-1040 Wien Karlsplatz 13 Tel. +43-1-58801-0 www.tuwien.ac.at #12;#12;Reliable Provisioning of Data-Centric a set of novel methods and tools for reliable provisioning of data-centric and event-based applications

  3. Comparison of Competing Software Reliability Models: Bayesian Model Selection

    E-Print Network [OSTI]

    Basu, Sanjib

    is in software development and testing. The goal of software reliability research is to quantify the performanceComparison of Competing Software Reliability Models: Bayesian Model Selection Sanjib Basu and Nader@math.niu.edu and nader@math.niu.edu Abstract Software reliability models are used to describe the evolution

  4. Security-Constrained Adequacy Evaluation of Bulk Power System Reliability

    E-Print Network [OSTI]

    contingency selection, (b) effects analysis, and (c) reliability index computation. Effects analysis as an optimization problem with the objective function being the bid cost function and congestion constraints and reliability index computations. The methodology is demonstrated with the IEEE reliability test system. Index

  5. Photovoltaic Module Reliability Workshop 2014: February 25-26, 2014

    SciTech Connect (OSTI)

    Kurtz, S.

    2014-02-01

    NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

  6. Photovoltaic Module Reliability Workshop 2013: February 26-27, 2013

    SciTech Connect (OSTI)

    Kurtz, S.

    2013-10-01

    NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

  7. Photovoltaic Module Reliability Workshop 2010: February 18-19, 2010

    SciTech Connect (OSTI)

    Kurtz, J.

    2013-11-01

    NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

  8. Photovoltaic Module Reliability Workshop 2011: February 16-17, 2011

    SciTech Connect (OSTI)

    Kurtz, S.

    2013-11-01

    NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

  9. Photovoltaic Module Reliability Workshop 2012: February 28 - March 1, 2012

    SciTech Connect (OSTI)

    Kurtz, S.

    2013-11-01

    NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

  10. Real Time Grid Reliability Management 2005

    SciTech Connect (OSTI)

    Eto, Joe; Eto, Joe; Lesieutre, Bernard; Lewis, Nancy Jo; Parashar, Manu

    2008-07-07

    The increased need to manage California?s electricity grid in real time is a result of the ongoing transition from a system operated by vertically-integrated utilities serving native loads to one operated by an independent system operator supporting competitive energy markets. During this transition period, the traditional approach to reliability management -- construction of new transmission lines -- has not been pursued due to unresolved issues related to the financing and recovery of transmission project costs. In the absence of investments in new transmission infrastructure, the best strategy for managing reliability is to equip system operators with better real-time information about actual operating margins so that they can better understand and manage the risk of operating closer to the edge. A companion strategy is to address known deficiencies in offline modeling tools that are needed to ground the use of improved real-time tools. This project: (1) developed and conducted first-ever demonstrations of two prototype real-time software tools for voltage security assessment and phasor monitoring; and (2) prepared a scoping study on improving load and generator response models. Additional funding through two separate subsequent work authorizations has already been provided to build upon the work initiated in this project.

  11. Using wind plant data to increase reliability.

    SciTech Connect (OSTI)

    Peters, Valerie A. (Sandia National Laboratories, Livermore, CA); Ogilvie, Alistair B.; McKenney, Bridget L.

    2011-01-01

    Operators interested in improving reliability should begin with a focus on the performance of the wind plant as a whole. To then understand the factors which drive individual turbine performance, which together comprise the plant performance, it is necessary to track a number of key indicators. Analysis of these key indicators can reveal the type, frequency, and cause of failures and will also identify their contributions to overall plant performance. The ideal approach to using data to drive good decisions includes first determining which critical decisions can be based on data. When those required decisions are understood, then the analysis required to inform those decisions can be identified, and finally the data to be collected in support of those analyses can be determined. Once equipped with high-quality data and analysis capabilities, the key steps to data-based decision making for reliability improvements are to isolate possible improvements, select the improvements with largest return on investment (ROI), implement the selected improvements, and finally to track their impact.

  12. Organization Chart

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEYI/O Streams for Large-scaleOrganization Chart Organization Charts

  13. Organizing Committee

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEYI/O Streams for Large-scaleOrganizationAbout EventsOrganizing

  14. Organizing Committee

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEYI/O Streams for Large-scaleOrganizationAboutOrganizing Committee

  15. Organizing Committee

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEYI/O Streams for Large-scaleOrganizationAboutOrganizing

  16. Review of Quantitative Software Reliability Methods

    SciTech Connect (OSTI)

    Chu, T.L.; Yue, M.; Martinez-Guridi, M.; Lehner, J.

    2010-09-17

    The current U.S. Nuclear Regulatory Commission (NRC) licensing process for digital systems rests on deterministic engineering criteria. In its 1995 probabilistic risk assessment (PRA) policy statement, the Commission encouraged the use of PRA technology in all regulatory matters to the extent supported by the state-of-the-art in PRA methods and data. Although many activities have been completed in the area of risk-informed regulation, the risk-informed analysis process for digital systems has not yet been satisfactorily developed. Since digital instrumentation and control (I&C) systems are expected to play an increasingly important role in nuclear power plant (NPP) safety, the NRC established a digital system research plan that defines a coherent set of research programs to support its regulatory needs. One of the research programs included in the NRC's digital system research plan addresses risk assessment methods and data for digital systems. Digital I&C systems have some unique characteristics, such as using software, and may have different failure causes and/or modes than analog I&C systems; hence, their incorporation into NPP PRAs entails special challenges. The objective of the NRC's digital system risk research is to identify and develop methods, analytical tools, and regulatory guidance for (1) including models of digital systems into NPP PRAs, and (2) using information on the risks of digital systems to support the NRC's risk-informed licensing and oversight activities. For several years, Brookhaven National Laboratory (BNL) has worked on NRC projects to investigate methods and tools for the probabilistic modeling of digital systems, as documented mainly in NUREG/CR-6962 and NUREG/CR-6997. However, the scope of this research principally focused on hardware failures, with limited reviews of software failure experience and software reliability methods. NRC also sponsored research at the Ohio State University investigating the modeling of digital systems using dynamic PRA methods. These efforts, documented in NUREG/CR-6901, NUREG/CR-6942, and NUREG/CR-6985, included a functional representation of the system's software but did not explicitly address failure modes caused by software defects or by inadequate design requirements. An important identified research need is to establish a commonly accepted basis for incorporating the behavior of software into digital I&C system reliability models for use in PRAs. To address this need, BNL is exploring the inclusion of software failures into the reliability models of digital I&C systems, such that their contribution to the risk of the associated NPP can be assessed.

  17. Advancing Usability Evaluation through Human Reliability Analysis

    SciTech Connect (OSTI)

    Ronald L. Boring; David I. Gertman

    2005-07-01

    This paper introduces a novel augmentation to the current heuristic usability evaluation methodology. The SPAR-H human reliability analysis method was developed for categorizing human performance in nuclear power plants. Despite the specialized use of SPAR-H for safety critical scenarios, the method also holds promise for use in commercial off-the-shelf software usability evaluations. The SPAR-H method shares task analysis underpinnings with human-computer interaction, and it can be easily adapted to incorporate usability heuristics as performance shaping factors. By assigning probabilistic modifiers to heuristics, it is possible to arrive at the usability error probability (UEP). This UEP is not a literal probability of error but nonetheless provides a quantitative basis to heuristic evaluation. When combined with a consequence matrix for usability errors, this method affords ready prioritization of usability issues.

  18. HUMAN RELIABILITY ANALYSIS FOR COMPUTERIZED PROCEDURES

    SciTech Connect (OSTI)

    Ronald L. Boring; David I. Gertman; Katya Le Blanc

    2011-09-01

    This paper provides a characterization of human reliability analysis (HRA) issues for computerized procedures in nuclear power plant control rooms. It is beyond the scope of this paper to propose a new HRA approach or to recommend specific methods or refinements to those methods. Rather, this paper provides a review of HRA as applied to traditional paper-based procedures, followed by a discussion of what specific factors should additionally be considered in HRAs for computerized procedures. Performance shaping factors and failure modes unique to computerized procedures are highlighted. Since there is no definitive guide to HRA for paper-based procedures, this paper also serves to clarify the existing guidance on paper-based procedures before delving into the unique aspects of computerized procedures.

  19. Nuclear Power - Control, Reliability and Human Factors†

    E-Print Network [OSTI]

    2011-01-01

    Reliability K s e n i i a Sapoz h n i k o v a and Roald Tayma n o v D.I.Mendeleyev Institute for Metrology, Russia 1. Introduction At present, a great number of embedded sens o r devi c es provi d e monito r i n g of operat i n g condi t io n... s and state of equi p me n t , includ i n g nucle a r react o r s of power plant s . The metrol o gi c a l reliab i li t y of meas uri n g instrum e n t s built in equi p me n t deter mi n e s the valid i t y of measure me nt infor ma t i o n . The qualit y...

  20. Wind Power Reliability: Breaking Down a Barrier

    Broader source: Energy.gov [DOE]

    The steady increase of wind power on the grid presents new challenges for power system operators charged with making sure the grid stays up and running. "We need to ensure that we are going down a path that will lead to better reliability [with wind power]," said Bob Zavadil, an executive vice president at EnerNex Corporation in Knoxville, Tenn., a firm specializing in renewable energy grid interconnection and integration. "If this piece isn't done, there will be problems." EnerNex has spent the last decade perfecting wind turbine and plant models that test a wind plant's influence on the grid and its ability to provide grid support. In its latest effort, the company is using American Recovery and Reinvestment Act funds worth $750,000 to develop documentation and validations of computer wind turbine models.

  1. Human Reliability Analysis for Small Modular Reactors

    SciTech Connect (OSTI)

    Ronald L. Boring; David I. Gertman

    2012-06-01

    Because no human reliability analysis (HRA) method was specifically developed for small modular reactors (SMRs), the application of any current HRA method to SMRs represents tradeoffs. A first- generation HRA method like THERP provides clearly defined activity types, but these activity types do not map to the human-system interface or concept of operations confronting SMR operators. A second- generation HRA method like ATHEANA is flexible enough to be used for SMR applications, but there is currently insufficient guidance for the analyst, requiring considerably more first-of-a-kind analyses and extensive SMR expertise in order to complete a quality HRA. Although no current HRA method is optimized to SMRs, it is possible to use existing HRA methods to identify errors, incorporate them as human failure events in the probabilistic risk assessment (PRA), and quantify them. In this paper, we provided preliminary guidance to assist the human reliability analyst and reviewer in understanding how to apply current HRA methods to the domain of SMRs. While it is possible to perform a satisfactory HRA using existing HRA methods, ultimately it is desirable to formally incorporate SMR considerations into the methods. This may require the development of new HRA methods. More practicably, existing methods need to be adapted to incorporate SMRs. Such adaptations may take the form of guidance on the complex mapping between conventional light water reactors and small modular reactors. While many behaviors and activities are shared between current plants and SMRs, the methods must adapt if they are to perform a valid and accurate analysis of plant personnel performance in SMRs.

  2. Probabilistic fatigue methodology and wind turbine reliability

    SciTech Connect (OSTI)

    Lange, C.H. [Stanford Univ., CA (United States)

    1996-05-01

    Wind turbines subjected to highly irregular loadings due to wind, gravity, and gyroscopic effects are especially vulnerable to fatigue damage. The objective of this study is to develop and illustrate methods for the probabilistic analysis and design of fatigue-sensitive wind turbine components. A computer program (CYCLES) that estimates fatigue reliability of structural and mechanical components has been developed. A FORM/SORM analysis is used to compute failure probabilities and importance factors of the random variables. The limit state equation includes uncertainty in environmental loading, gross structural response, and local fatigue properties. Several techniques are shown to better study fatigue loads data. Common one-parameter models, such as the Rayleigh and exponential models are shown to produce dramatically different estimates of load distributions and fatigue damage. Improved fits may be achieved with the two-parameter Weibull model. High b values require better modeling of relatively large stress ranges; this is effectively done by matching at least two moments (Weibull) and better by matching still higher moments. For this purpose, a new, four-moment {open_quotes}generalized Weibull{close_quotes} model is introduced. Load and resistance factor design (LRFD) methodology for design against fatigue is proposed and demonstrated using data from two horizontal-axis wind turbines. To estimate fatigue damage, wind turbine blade loads have been represented by their first three statistical moments across a range of wind conditions. Based on the moments {mu}{sub 1}{hor_ellipsis}{mu}{sub 3}, new {open_quotes}quadratic Weibull{close_quotes} load distribution models are introduced. The fatigue reliability is found to be notably affected by the choice of load distribution model.

  3. Field Testing Protocol Atlantic and Gulf Coastal Plain Regional Supplement

    E-Print Network [OSTI]

    US Army Corps of Engineers

    Field Testing Protocol Atlantic and Gulf Coastal Plain Regional Supplement Organization of field the field testing of the draft Regional Supplement. Field testing will be done in cooperation with regional, the District coordinator will provide team members with an introduction to the Regional Supplement

  4. Auditing the Structural Reliability of the Clouds

    E-Print Network [OSTI]

    Haller, Gary L.

    . Icebergs in the Clouds: the Other Risks of Cloud Computing. In HotCloud, 2012. #12;Correlated Failures of occurrences. #12;Talk Outline Challenges Our approach Evaluation #12;Talk Outline Challenges Our approach Evaluation #12;Challenges 1. How to acquire dependency information automatically? 2. How to organize

  5. Volatile organic compound sensor system

    DOE Patents [OSTI]

    Schabron, John F.; Rovani, Jr., Joseph F.; Bomstad, Theresa M.; Sorini-Wong, Susan S.; Wong, Gregory K.

    2011-03-01

    Generally, this invention relates to the development of field monitoring methodology for new substances and sensing chemical warfare agents (CWAs) and terrorist substances. It also relates to a portable test kit which may be utilized to measure concentrations of halogenated volatile organic compounds (VOCs) in the field. Specifically it relates to systems for reliably field sensing the potential presence of such items while also distinguishing them from other elements potentially present. It also relates to overall systems and processes for sensing, reacting, and responding to an indicated presence of such substance, including modifications of existing halogenated sensors and arrayed sensing systems and methods.

  6. Volatile organic compound sensor system

    DOE Patents [OSTI]

    Schabron, John F. (Laramie, WY); Rovani, Jr., Joseph F. (Laramie, WY); Bomstad, Theresa M. (Laramie, WY); Sorini-Wong, Susan S. (Laramie, WY)

    2009-02-10

    Generally, this invention relates to the development of field monitoring methodology for new substances and sensing chemical warfare agents (CWAs) and terrorist substances. It also relates to a portable test kit which may be utilized to measure concentrations of halogenated volatile organic compounds (VOCs) in the field. Specifically it relates to systems for reliably field sensing the potential presence of such items while also distinguishing them from other elements potentially present. It also relates to overall systems and processes for sensing, reacting, and responding to an indicated presence of such substance, including modifications of existing halogenated sensors and arrayed sensing systems and methods.

  7. Secure and reliable operation of our

    E-Print Network [OSTI]

    Amin, S. Massoud

    the weather. Electric power systems constitute the fundamental infrastructure of modern society. A suc attack intended to bring down an entire regional grid. Similarly, the attack could target electricity to national and international economy, security, and quality of life. Massoud Amin, Electric Power Research

  8. Estimated Value of Service Reliability for Electric Utility Customers in the United States

    SciTech Connect (OSTI)

    Sullivan, M.J.; Mercurio, Matthew; Schellenberg, Josh

    2009-06-01

    Information on the value of reliable electricity service can be used to assess the economic efficiency of investments in generation, transmission and distribution systems, to strategically target investments to customer segments that receive the most benefit from system improvements, and to numerically quantify the risk associated with different operating, planning and investment strategies. This paper summarizes research designed to provide estimates of the value of service reliability for electricity customers in the US. These estimates were obtained by analyzing the results from 28 customer value of service reliability studies conducted by 10 major US electric utilities over the 16 year period from 1989 to 2005. Because these studies used nearly identical interruption cost estimation or willingness-to-pay/accept methods it was possible to integrate their results into a single meta-database describing the value of electric service reliability observed in all of them. Once the datasets from the various studies were combined, a two-part regression model was used to estimate customer damage functions that can be generally applied to calculate customer interruption costs per event by season, time of day, day of week, and geographical regions within the US for industrial, commercial, and residential customers. Estimated interruption costs for different types of customers and of different duration are provided. Finally, additional research and development designed to expand the usefulness of this powerful database and analysis are suggested.

  9. Assistance Focus: Asia/Pacific Region (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2015-01-01

    The Clean Energy Solutions Center Ask an Expert service connects governments seeking policy information and advice with one of more than 30 global policy experts who can provide reliable and unbiased quick-response advice and information. The service is available at no cost to government agency representatives from any country and the technical institutes assisting them. This publication presents summaries of assistance provided to governments in the Asia/Pacific region, including the benefits of that assistance.

  10. Regional Summary Pacific Region Management Context

    E-Print Network [OSTI]

    Pacific Rim nations. As such, the management of the HMS fisheries s coordinated by the Pacific FisheryRegional Summary Pacific Region Management Context The Pacific Region includes California, Oregon, and Washington. Federal fisheries in this region are managed by the Pacific Fishery Management Council (PFMC

  11. Colorado Regional Faults

    SciTech Connect (OSTI)

    Hussein, Khalid

    2012-02-01

    Citation Information: Originator: Earth Science &Observation Center (ESOC), CIRES, University of Colorado at Boulder Originator: Colorado Geological Survey (CGS) Publication Date: 2012 Title: Regional Faults Edition: First Publication Information: Publication Place: Earth Science & Observation Center, Cooperative Institute for Research in Environmental Science, University of Colorado, Boulder Publisher: Earth Science &Observation Center (ESOC), CIRES, University of Colorado at Boulder Description: This layer contains the regional faults of Colorado Spatial Domain: Extent: Top: 4543192.100000 m Left: 144385.020000 m Right: 754585.020000 m Bottom: 4094592.100000 m Contact Information: Contact Organization: Earth Science &Observation Center (ESOC), CIRES, University of Colorado at Boulder Contact Person: Khalid Hussein Address: CIRES, Ekeley Building Earth Science & Observation Center (ESOC) 216 UCB City: Boulder State: CO Postal Code: 80309-0216 Country: USA Contact Telephone: 303-492-6782 Spatial Reference Information: Coordinate System: Universal Transverse Mercator (UTM) WGSí1984 Zone 13N False Easting: 500000.00000000 False Northing: 0.00000000 Central Meridian: -105.00000000 Scale Factor: 0.99960000 Latitude of Origin: 0.00000000 Linear Unit: Meter Datum: World Geodetic System 1984 (WGS í984) Prime Meridian: Greenwich Angular Unit: Degree Digital Form: Format Name: Shape file

  12. Human Reliability Considerations for Small Modular Reactors

    SciTech Connect (OSTI)

    OHara J. M.; Higgins, H.; DAgostino, A.; Erasmia, L.

    2012-01-27

    Small modular reactors (SMRs) are a promising approach to meeting future energy needs. Although the electrical output of an individual SMR is relatively small compared to that of typical commercial nuclear plants, they can be grouped to produce as much energy as a utility demands. Furthermore, SMRs can be used for other purposes, such as producing hydrogen and generating process heat. The design characteristics of many SMRs differ from those of current conventional plants and may require a distinct concept of operations. The U.S. Nuclear Regulatory Commission (NRC) conducted research to examine the human factors engineering and the operational aspects of SMRs. The research identified thirty potential human-performance issues that should be considered in the NRC's reviews of SMR designs and in future research activities. The purpose of this report is to illustrate how the issues can support SMR probabilistic risk analyses and their review by identifying potential human failure events for a subset of the issues. As part of addressing the human contribution to plant risk, human reliability analysis practitioners identify and quantify the human failure events that can negatively impact normal or emergency plant operations. The results illustrated here can be generalized to identify additional human failure events for the issues discussed and can be applied to those issues not discussed in this report.

  13. Individual Differences in Human Reliability Analysis

    SciTech Connect (OSTI)

    Jeffrey C. Joe; Ronald L. Boring

    2014-06-01

    While human reliability analysis (HRA) methods include uncertainty in quantification, the nominal model of human error in HRA typically assumes that operator performance does not vary significantly when they are given the same initiating event, indicators, procedures, and training, and that any differences in operator performance are simply aleatory (i.e., random). While this assumption generally holds true when performing routine actions, variability in operator response has been observed in multiple studies, especially in complex situations that go beyond training and procedures. As such, complexity can lead to differences in operator performance (e.g., operator understanding and decision-making). Furthermore, psychological research has shown that there are a number of known antecedents (i.e., attributable causes) that consistently contribute to observable and systematically measurable (i.e., not random) differences in behavior. This paper reviews examples of individual differences taken from operational experience and the psychological literature. The impact of these differences in human behavior and their implications for HRA are then discussed. We propose that individual differences should not be treated as aleatory, but rather as epistemic. Ultimately, by understanding the sources of individual differences, it is possible to remove some epistemic uncertainty from analyses.

  14. High reliability plastic packaging for microelectronics

    SciTech Connect (OSTI)

    Sweet, J.N.; Peterson, D.W.; Hsia, A.H.; Tuck, M.

    1997-07-01

    Goal was Assembly Test Chips (ATCs) which could be used for evaluating plastic encapsulation technologies. Circuits were demonstrated for measuring Au-Al wirebond and Al metal corrosion failure rates during accelerated temperature and humidity testing. The test circuits on the ATC02.5 chip were very sensitive to extrinsic or processing induced failure rates. Accelerated aging experiments were conducted with unpassivated triple track Al structures on the ATC02.6 chip; the unpassivated tracks were found to be very sensitive to particulate contamination. Some modifications to existing circuitry were suggested. The piezoresistive stress sensing circuitry designed for the ATC04 test chip was found suitable for determining the change in the state of mechanical stress at the die when both initial and final measurements were made near room temperature (RT). Attempt to measure thermal stress between RT and a typical polymer glass transition temperature failed because of excessive die resistor- substrate leakage currents at the high temperature end; suitable circuitry changes were developed to overcome this problem. One temperature and humidity experiment was conducted with Sandia developed static radom access memory parts to examine non-corrosion CMOS failures; this objective was not achieved, but corrosion failure at the metal to Si contacts on the die surface could be detected. This 2-year effort resulted in new designs for test circuits which could be used on an advanced ATC for reliability assessment in Defense Programs electronics development projects.

  15. Office of Electricity Delivery and Energy Reliability | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    & Internships Funding Opportunities Information Center Contact Us Energy.gov Office of Electricity Delivery & Energy Reliability 1000 Independence Avenue, SW Washington, DC...

  16. Reliability of Coupled Oscillators I: Two-Oscillator Systems

    E-Print Network [OSTI]

    Kevin K. Lin; Eric Shea-Brown; Lai-Sang Young

    2007-08-23

    This paper concerns the reliability of a pair of coupled oscillators in response to fluctuating inputs. Reliability means that an input elicits essentially identical responses upon repeated presentations regardless of the network's initial condition. Our main result is that both reliable and unreliable behaviors occur in this network for broad ranges of coupling strengths, even though individual oscillators are always reliable when uncoupled. A new finding is that at low input amplitudes, the system is highly susceptible to unreliable responses when the feedforward and feedback couplings are roughly comparable. A geometric explanation based on shear-induced chaos at the onset of phase-locking is proposed.

  17. Electro-thermal-mechanical Simulation and Reliability for Plug...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Meeting ape026hefner2012o.pdf More Documents & Publications Electro-thermal-mechanical Simulation and Reliability for Plug-in Vehicle Converters and Inverters...

  18. POWER, THERMAL, AND RELIABILITY MODELING IN NANOMETER-SCALE

    E-Print Network [OSTI]

    Brooks, David

    ........................................................................................................................................................................................................................................................ POWER ........................................................................................................................................................................................................................................................ POWER IS THE SOURCE OF THE GREATEST PROBLEMS FACING MICROPROCESSOR DESIGNERS. RAPID POWER VARIATION BRINGS TRANSIENT ERRORS. HIGH POWER DENSITIES BRING HIGH TEMPERATURES, HARMING RELIABILITY AND INCREASING

  19. Smart Grid: Creating Jobs while Delivering Reliable,Environmentally...

    Open Energy Info (EERE)

    Smart Grid: Creating Jobs while Delivering Reliable, Environmentally-friendly Energy Home > Groups > OpenEI Community Central Graham7781's picture Submitted by Graham7781(2017)...

  20. Reliability Tools for Resonance Inspection of Light Metal Castings...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tools for Resonance Inspection of Light Metal Castings Reliability Tools for Resonance Inspection of Light Metal Castings 2012 DOE Hydrogen and Fuel Cells Program and Vehicle...

  1. Summary of the Optics, IR, Injection, Operations, Reliability...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Summary of the Optics, IR, Injection, Operations, Reliability and Instrumentation Working Group Citation Details In-Document Search Title: Summary of the Optics,...

  2. Sandia Energy - Reliability, O&M, Standards Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    design, wind industry data collection and storage techniques, and analysis methods. The IEA Task 33 Working Group on Reliability Data unites experts from around the world, with...

  3. Clean, Efficient, and Reliable Power for the 21st Century

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and combined-heat-and-power, where they provide unparalleled reliability and en- hanced efficiency. Continuing technological progress will enable fuel cells to compete in new...

  4. Combined Heat and Power System Enables 100% Reliability at Leading...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    buildings on nearly 1,000 acres. Photo courtesy of Thermal Energy Corporation Combined Heat and Power System Enables 100% Reliability at Leading Medical Campus Recovery Act...

  5. Project Profile: Physics-Based Reliability Models for Supercritical...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    developed models to predict the reliability of hybrid gas bearing (HGB) and dry gas seal (DGS) components in the turboexpander of a supercritical CO2 turbine. The...

  6. Separating myths from reality in PV inverter reliability

    E-Print Network [OSTI]

    Rollins, Andrew M.

    . ∑ This is based upon a LCOE of 5 cents per kWh, so reliability is critical ∑ MTBF of string inverters in 2006: 5

  7. Power Electronics Reliability Kick Off Meeting ? Silicon Power...

    Office of Environmental Management (EM)

    Electronics Reliability Analysis Annual DOE Peer Review Meeting October 8, 2009 Mark A. Smith - Systems Readiness & Sustainment Technologies Department Stan Atcitty - Energy...

  8. Office of Electricity Delivery And Energy Reliability To Hold...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Office of Electricity Delivery And Energy Reliability To Hold Technical Conference On The Design Of Future Electric Transmission Office of Electricity Delivery And Energy...

  9. Guide to Using Combined Heat and Power for Enhancing Reliability...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Heat and Power for Enhancing Reliability and Resiliency in Buildings During and after Hurricane Sandy, combined heat and power (CHP) enabled a number of critical infrastructure and...

  10. Assembly and comparison of available solar hot water system reliability databases and information.

    SciTech Connect (OSTI)

    Menicucci, David F.

    2009-05-01

    Solar hot water (SHW) systems have been installed commercially for over 30 years, yet few quantitative details are known about their reliability. This report describes a comprehensive analysis of all of the known major previous research and data regarding the reliability of SHW systems and components. Some important conclusions emerged. First, based on a detailed inspection of ten-year-old systems in Florida, about half of active systems can be expected to fail within a ten-year period. Second, valves were identified as the probable cause of a majority of active SHW failures. Third, passive integral and thermosiphon SHW systems have much lower failure rates than active ones, probably due to their simple design that employs few mechanical parts. Fourth, it is probable that the existing data about reliability do not reveal the full extent of fielded system failures because most of the data were based on trouble calls. Often an SHW system owner is not aware of a failure because the backup system silently continues to produce hot water. Thus, a repair event may not be generated in a timely manner, if at all. This final report for the project provides all of the pertinent details about this study, including the source of the data, the techniques to assure their quality before analysis, the organization of the data into perhaps the most comprehensive reliability database in existence, a detailed statistical analysis, and a list of recommendations for additional critical work. Important recommendations include the inclusion of an alarm on SHW systems to identify a failed system, the need for a scientifically designed study to collect high-quality reliability data that will lead to design improvements and lower costs, and accelerated testing of components that are identified as highly problematic.

  11. Organizing Committee

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEYI/O Streams for Large-scaleOrganizationAbout Events

  12. Organizing Committee

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEYI/O Streams for Large-scaleOrganizationAbout

  13. Gearbox Reliability Collaborative Project Report: Findings from Phase 1 and Phase 2 Testing

    SciTech Connect (OSTI)

    Link, H.; LaCava, W.; van Dam, J.; McNiff, B.; Sheng, S.; Wallen, R.; McDade, M.; Lambert, S.; Butterfield, S.; Oyague, F.

    2011-06-01

    This report describes the Gearbox Reliability Collaborative's work at NREL to increase the reliability of wind turbine gearboxes.

  14. Reliability Testing of Polysilicon For MEMs Devices

    SciTech Connect (OSTI)

    LaVan, D.A.; Buchheit, T.E.

    1999-04-05

    Mission critical applications of MEMS devices require knowledge of the distribution in their material properties and long-term reliability of the small-scale structures. This project reports on a new testing program at Sandia to quantify the strength distribution using samples that reflect the dimensions of critical MEMS components. The strength of polysilicon fabricated with Sandia's SUMMiT 4-layer process was successfully measured using samples with gage sections 2.5 {micro}m thick by 1.7 {micro}m wide and lengths of 15 and 25 {micro}m. These tensile specimens have a freely moving pivot on one end that anchors the sample to the silicon die and prevents off axis loading during testing. Each sample is loaded in uniaxial tension by pulling laterally with a flat tipped diamond in a computer-controlled Nanoindenter. The stress-strain curve is calculated using the specimen cross section and gage length dimensions verified by measuring against a standard in the SEM. The first 48 samples had a means strength of 2.24 {+-} 0.35 GPa. Fracture strength measurements grouped into three strength levels, which matched three failure modes observed in post mortem examinations. The seven samples in the highest strength group failed in the gage section (strength of 2.77 {+-} 0.04 GPa), the moderate strength group failed at the gage section fillet and the lowest strength group failed at a dimple in the hub. With this technique, multiple tests can be programmed at one time and performed without operator assistance at a rate of 20-30 per day allowing the collection of significant populations of data. Since the new test geometry has been proven, the project is moving to test the distributions seen from real geometric features typical to MEMS such as the effect of gage length, fracture toughness, bonding between layers, etch holes, dimples and shear of gear teeth.

  15. Heterogeneity for Increasing Performance and Reliability of Self-Reconfigurable Multi-Robot Organisms

    E-Print Network [OSTI]

    Kernbach, S; Humza, R; Liedke, J; Popesku, S; Russo, S; Ranzani, T; Manfredi, L; Stefanini, C; Matthias, R; Schwarzer, Ch; Girault, B; Alschbach, P; Meister, E; Scholz, O

    2011-01-01

    Homogeneity and heterogeneity represent a well-known trade-off in the design of modular robot systems. This work addresses the heterogeneity concept, its rationales, design choices and performance evaluation. We introduce challenges for self-reconfigurable systems, show advances of mechatronic and software design of heterogeneous platforms and discuss experiments, which intend to demonstrate usability and performance of this system.

  16. The Constitution of Highly Reliable Practices: Materializing Communication as Constitutive of Organizing

    E-Print Network [OSTI]

    Spradley, Robert Tyler

    2012-10-19

    on collective mind, this study uses a practice-based communication approach to examine the material interplay of bodies, objects, and sites using ethnography and grounded theory. In-depth interviews, participant observations, and organizational documents were...

  17. July 24, 2009, Visiting Speakers Program - Regulation and High Reliability Organizations by Dr. Jerry Ellig

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on DeliciousMathematicsEnergyInterested Parties - WAPA Public CommentInverted Attic9: HSS FocusRegulation and High

  18. Towards Reliable SubDivision of Geological Areas: Interval Approach

    E-Print Network [OSTI]

    Kreinovich, Vladik

    Towards Reliable Sub≠Division of Geological Areas: Interval Approach David D. Coblentz 1;2 , Vladik difficult to produce a reliable subdivision. The subdivision of a geological zone into segments is often, and often, we do not have a statistically sufficient amount of thoroughly analyzed geological samples

  19. Towards Reliable SubDivision of Geological Areas: Interval Approach

    E-Print Network [OSTI]

    Kreinovich, Vladik

    Towards Reliable Sub≠Division of Geological Areas: Interval Approach David D. Coblentz 1;2 , Vladik Difficult to Produce a Reliable Subdivision The subdivision of a geological zone into segments is often the area, and often, we do not have a statistically sufficient amount of thoroughly analyzed geological

  20. SCORE: a Scalable Concolic Testing Tool for Reliable Embedded Software

    E-Print Network [OSTI]

    SCORE: a Scalable Concolic Testing Tool for Reliable Embedded Software Yunho Kim and Moonzoo Kim COncolic testing tool for REliable embedded software (SCORE) that targets embedded C programs. SCORE is a de-facto standard method for improving the quality of software in industry. Conventional testing

  1. INTELLIGENT SENSOR VALIDATION AND SENSOR FUSION FOR RELIABILITY AND SAFETY

    E-Print Network [OSTI]

    Agogino, Alice M.

    1 INTELLIGENT SENSOR VALIDATION AND SENSOR FUSION FOR RELIABILITY AND SAFETY ENHANCEMENT IN VEHICLE #12;2 Intelligent Sensor Validation and Sensor Fusion for Reliability and Safety Enhancement acknowledge the help of PATH engineers Pete Devlin, Seibum Choi, and Leon Chen. II. Keywords Sensor Validation

  2. RELIABILITY COMPARISON MODELS FOR OFFSHORE WIND TURBINES (OWT)

    E-Print Network [OSTI]

    Bernstein, Joseph B.

    RELIABILITY COMPARISON MODELS FOR OFFSHORE WIND TURBINES (OWT) Yizhou Lu, T. M. Delorm, A. Christou of survivor functions R(t) of drive-trains, after 1 year of operation, between Offshore Wind Turbine (OWT) vs of the reliability of these 5 Types Surrogate failure rate data Onshore wind turbines (OT) 1-1.5MW CONCLUSIONS

  3. UNCORRECTED Reliability analysis of hybrid ceramic/steel gun barrels

    E-Print Network [OSTI]

    Grujicic, Mica

    UNCORRECTED PROOF Reliability analysis of hybrid ceramic/steel gun barrels M. GRUJICIC1 , J. R-5069, USA Received in final form 25 February 2002 AB ST R AC T Failure of the ceramic gun-barrel lining probability for the lining is also discussed. Keywords failure; gun-barrel lining; reliability; thermo

  4. EE 851.3 (3L) Power System Reliability

    E-Print Network [OSTI]

    Saskatchewan, University of

    EE 851.3 (3L) Power System Reliability Department of Electrical and Computer Engineering Winter and Program Catalogue) Prerequisites: EE 850 or prior knowledge of reliability engineering concepts Instructor: Rajesh Karki, Ph.D., P.Eng. Associate Professor, Department of Electrical and Computer Engineering Office

  5. Gearbox Reliability Collaborative High Speed Shaft Tapered Roller Bearing Calibration

    SciTech Connect (OSTI)

    Keller, J.; Guo, Y.; McNiff, B.

    2013-10-01

    The National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC) is a project investigating gearbox reliability primarily through testing and modeling. Previous dynamometer testing focused upon acquiring measurements in the planetary section of the test gearbox. Prior to these tests, the strain gages installed on the planetary bearings were calibrated in a load frame.

  6. An Empirical Study of the Reliability UNIX Utilities

    E-Print Network [OSTI]

    Miller, Barton P.

    An Empirical Study of the Reliability of UNIX Utilities Barton P. Miller bart@cs.wisc.edu Lars, such as the kernel and utility programs, are typically assumed to be reliable. In our recent experiments, we have been able to crash 25≠33% of the utility programs on any version of UNIX that was tested. This report

  7. An Empirical Study of the Reliability UNIX Utilities

    E-Print Network [OSTI]

    Miller, Barton P.

    An Empirical Study of the Reliability of UNIX Utilities Barton P. Miller bart@cs.wisc.edu Lars, such as the kernel and utility programs, are typically assumed to be reliable. In our recent experiments, we have been able to crash 25-33% of the utility programs on any version of UNIX that was tested. This report

  8. Hybrid Statistical Model Checking Technique for Reliable Safety Critical Systems

    E-Print Network [OSTI]

    @cs.kaist.ac.kr Abstract--Reliability of safety critical systems such as nuclear power plants and automobiles has become1 Hybrid Statistical Model Checking Technique for Reliable Safety Critical Systems Youngjoo Kim a significant issue to our society. As more computing systems are utilized in these safety critical systems

  9. Assessing the reliability of linear dynamic transformer thermal modelling

    E-Print Network [OSTI]

    Assessing the reliability of linear dynamic transformer thermal modelling X. Mao, D.J. Tylavsky and G.A. McCulla Abstract: Improving the utilisation of transformers requires that the hot-spot and top. An alternative method for assessing transformer model reliability is provided. 1 Introduction The maximally

  10. Wind turbine reliability : a database and analysis approach.

    SciTech Connect (OSTI)

    Linsday, James; Briand, Daniel; Hill, Roger Ray; Stinebaugh, Jennifer A.; Benjamin, Allan S.

    2008-02-01

    The US wind Industry has experienced remarkable growth since the turn of the century. At the same time, the physical size and electrical generation capabilities of wind turbines has also experienced remarkable growth. As the market continues to expand, and as wind generation continues to gain a significant share of the generation portfolio, the reliability of wind turbine technology becomes increasingly important. This report addresses how operations and maintenance costs are related to unreliability - that is the failures experienced by systems and components. Reliability tools are demonstrated, data needed to understand and catalog failure events is described, and practical wind turbine reliability models are illustrated, including preliminary results. This report also presents a continuing process of how to proceed with controlling industry requirements, needs, and expectations related to Reliability, Availability, Maintainability, and Safety. A simply stated goal of this process is to better understand and to improve the operable reliability of wind turbine installations.

  11. Joint Architecture Standard (JAS) Reliable Data Delivery Protocol (RDDP) specification.

    SciTech Connect (OSTI)

    Enderle, Justin Wayne; Daniels, James W.; Gardner, Michael T.; Eldridge, John M.; Hunt, Richard D.; Gallegos, Daniel E.

    2011-05-01

    The Joint Architecture Standard (JAS) program at Sandia National Laboratories requires the use of a reliable data delivery protocol over SpaceWire. The National Aeronautics and Space Administration at the Goddard Spaceflight Center in Greenbelt, Maryland, developed and specified a reliable protocol for its Geostationary Operational Environment Satellite known as GOES-R Reliable Data Delivery Protocol (GRDDP). The JAS program implemented and tested GRDDP and then suggested a number of modifications to the original specification to meet its program specific requirements. This document details the full RDDP specification as modified for JAS. The JAS Reliable Data Delivery Protocol uses the lower-level SpaceWire data link layer to provide reliable packet delivery services to one or more higher-level host application processes. This document specifies the functional requirements for JRDDP but does not specify the interfaces to the lower- or higher-level processes, which may be implementation-dependent.

  12. Is This Cost Estimate Reliable?Is This Cost Estimate Reliable? -The Relationship between Homogeneity of Analogues

    E-Print Network [OSTI]

    Bae, Doo-Hwan

    Is This Cost Estimate Reliable?Is This Cost Estimate Reliable? - The Relationship between/4)( / ) Software cost estimation Definition ∑ Task of predicting the cost required to complete a software projectproject Techniques for software cost estimation ∑ Algorithmic estimationAlgorithmic estimation ≠ Calculate

  13. New International Program to Asses the Reliability of Emerging Nondestructive Techniques (PARENT)

    SciTech Connect (OSTI)

    Prokofiev, Iouri; Cumblidge, Stephen E.; Csontos, Aladar A.; Braatz, Brett G.; Doctor, Steven R.

    2013-01-25

    The Nuclear Regulatory Commission (NRC) established the Program to Assess the Reliability of Emerging Nondestructive Techniques (PARENT) to follow on from the successful Program for the Inspection of Nickel alloy Components (PINC). The goal of the PARENT is to conduct a confirmatory assessment of the reliability of nondestructive evaluation (NDE) techniques for detecting and sizing primary water stress corrosion cracks (PWSCC) and applying the lessons learned from PINC to a series of round-robin tests. These open and blind round-robin tests will comprise a new set of typical pressure boundary components including dissimilar metal welds (DMWs) and bottom-mounted instrumentation penetrations. Open round-robin tests will engage research and industry teams worldwide to investigate and demonstrate the reliability of emerging NDE techniques to detect and size flaws with a wide range of lengths, depths, orientations, and locations. Blind round-robin tests will utilize various testing organizations, whose inspectors and procedures are certified by the standards for the nuclear industry in their respective countries, to investigate the ability of established NDE techniques to detect and size flaws whose characteristics range from relatively easy to very difficult for detection and sizing. Blind and open round-robin testing started in late 2011 and early 2012, respectively. This paper will present the work scope with reports on progress, NDE methods evaluated, and project timeline for PARENT.

  14. Field Testing Protocol Western Mountains, Valleys and Coast Regional Supplement

    E-Print Network [OSTI]

    US Army Corps of Engineers

    Field Testing Protocol Western Mountains, Valleys and Coast Regional Supplement Organization and oversee the field testing of the draft Regional Supplement. Field testing will be done in cooperation, the District coordinator will provide team members with an introduction to the Regional Supplement

  15. Robust Design of Reliability Test Plans Using Degradation Measures.

    SciTech Connect (OSTI)

    Lane, Jonathan Wesley; Lane, Jonathan Wesley; Crowder, Stephen V.; Crowder, Stephen V.

    2014-10-01

    With short production development times, there is an increased need to demonstrate product reliability relatively quickly with minimal testing. In such cases there may be few if any observed failures. Thus, it may be difficult to assess reliability using the traditional reliability test plans that measure only time (or cycles) to failure. For many components, degradation measures will contain important information about performance and reliability. These measures can be used to design a minimal test plan, in terms of number of units placed on test and duration of the test, necessary to demonstrate a reliability goal. Generally, the assumption is made that the error associated with a degradation measure follows a known distribution, usually normal, although in practice cases may arise where that assumption is not valid. In this paper, we examine such degradation measures, both simulated and real, and present non-parametric methods to demonstrate reliability and to develop reliability test plans for the future production of components with this form of degradation.

  16. Regional Transportation Coordination Study†

    E-Print Network [OSTI]

    Golden Crescent Regional Planning Commission

    2006-01-01

    stream_source_info Golden Crescent Regional Transportation Coordination Study.pdf.txt stream_content_type text/plain stream_size 357268 Content-Encoding ISO-8859-1 stream_name Golden Crescent Regional Transportation Coordination... Study.pdf.txt Content-Type text/plain; charset=ISO-8859-1 Golden Crescent Regional Transit i Regional Transportation Coordination Study: 7-County Golden Crescent Region Regional...

  17. Reliable and unreliable dynamics in driven coupled oscillators

    E-Print Network [OSTI]

    Kevin K. Lin; Eric Shea-Brown; Lai-Sang Young

    2006-08-10

    This letter concerns the reliability of coupled oscillator networks in response to fluctuating inputs. Reliability means that (following a transient) an input elicits identical responses upon repeated presentations, regardless of the system's initial condition. Here, we analyze this property for two coupled oscillators, demonstrating that oscillator networks exhibit both reliable and unreliable dynamics for broad ranges of coupling strengths. We further argue that unreliable dynamics are characterized by strange attractors with random SRB measures, implying that though unreliable, the responses lie on low-dimensional sets. Finally, we show that 1:1 phase locking in the zero-input system corresponds to high susceptibility for unreliable responses. A geometric explanation is proposed.

  18. Clean Energy Manufacturing Initiative Southeast Regional Summit

    Broader source: Energy.gov [DOE]

    As part of the Clean Energy Manufacturing Initiative (CEMI), the U.S. Department of Energy (DOE) organizes regional summits around the country to expand its partnerships, share resources and successes, and refine its strategy to boost U.S. competitiveness in clean energy manufacturing. The CEMI Southeast Regional Summit, which will be held on July 9, 2015 at the Renaissance Atlanta Midtown Hotel in Atlanta, Georgia, is the third in this series.

  19. Reliability Modeling and Evaluation in Aging Power Systems†

    E-Print Network [OSTI]

    Kim, Hag-Kwen

    2010-01-14

    Carlo simulation is introduced. Power Law Process is modeled as the failure rate function of aging components. Power system reliability analysis can be made at the generation capacity level where transmission constraints may be included. The simulation...

  20. Estimation of system reliability using a semiparametric model

    E-Print Network [OSTI]

    Wu, Leon

    An important problem in reliability engineering is to predict the failure rate, that is, the frequency with which an engineered system or component fails. This paper presents a new method of estimating failure rate using ...

  1. RELIABILITY OF WIND POWER FROM DISPERSED SITES: A PRELIMINARY ASSESSMENT

    E-Print Network [OSTI]

    Kahn, E.

    2011-01-01

    ON METHODOLOGY: FROM WIND POWER FREQUENCY TO LOSS-OF-LOADJ.P. , "Some Aspects of Wind Power Statistics, " J. of Appl.S£CTION Reliability of Wind Power From Dispersed Sites: A Pr

  2. Travel Time Reliability: Its Measurement and Prediction | ornl...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Travel Time Reliability: Its Measurement and Prediction Apr 02 2014 10:00 AM - 11:00 AM George List, North Carolina State University, Raleigh, and Richard Margiotta, Cambridge...

  3. Transmission Reliability "Load as a Resource" Peer Review Materials...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    "Load as a Resource" Peer Review Materials Now Available Transmission Reliability "Load as a Resource" Peer Review Materials Now Available September 25, 2014 - 11:43am Addthis OE's...

  4. Multi-hazard Reliability Assessment of Offshore Wind Turbines†

    E-Print Network [OSTI]

    Mardfekri Rastehkenari, Maryam 1981-

    2012-12-04

    A probabilistic framework is developed to assess the structural reliability of offshore wind turbines. Probabilistic models are developed to predict the deformation, shear force and bending moment demands on the support structure of wind turbines...

  5. Energy and Reliability in Future NOC Interconnected CMPS†

    E-Print Network [OSTI]

    Kim, Hyungjun

    2013-08-01

    In this dissertation, I explore energy and reliability in future NoC (Network-on-Chip) interconnected CMPs (chip multiprocessors) as they have become a first-order constraint in future CMP design. In the first part, we ...

  6. Massachusetts Institute of Technology Reliable Secret Sharing With

    E-Print Network [OSTI]

    Marten van Dijk, Daihyun Lim, Srinivas Devadas 2004 Computation Structures Group Memo 475 The Stata Laboratory #12;#12;Reliable Secret Sharing With Physical Random Functions Marten van Dijk Daihyun Lim

  7. Experiences with Two Reliability Data Collection Efforts (Presentation)

    SciTech Connect (OSTI)

    Sheng, S.; Lantz, E.

    2013-08-01

    This presentation, given by NREL at the Wind Reliability Experts Meeting in Albuquerque, New Mexico, outlines the causes of wind plant operational expenditures and gearbox failures and describes NREL's efforts to create a gearbox failure database.

  8. Reliability improvement project decision making : water cooling system redesign

    E-Print Network [OSTI]

    Devine, Paul (Paul S.)

    2006-01-01

    Deciding on which reliability & performance improvement projects to launch or to reject has historically been an extremely challenging responsibility of Teradyne management. Incorrect decisions can lead to major customer ...

  9. Request for Information: Photovoltaic Reliability and Durability Research and Development

    Broader source: Energy.gov [DOE]

    The United States Department of Energy (DOE) Ė Office of Energy Efficiency and Renewable Energy (EERE) seeks feedback from industry, academia, research laboratories, government agencies, and other stakeholders on issues related to solar photovoltaic (PV) reliability and durability research and development.

  10. Enhanced Reliability of Photovoltaic Systems with Energy Storage and Controls

    SciTech Connect (OSTI)

    Manz, D.; Schelenz, O.; Chandra, R.; Bose, S.; de Rooij, M.; Bebic, J.

    2008-02-01

    This report summarizes efforts to reconfigure loads during outages to allow individual customers the opportunity to enhance the reliability of their electric service through the management of their loads, photovoltaics, and energy storage devices.

  11. Some optimization problems in power system reliability analysis†

    E-Print Network [OSTI]

    Jirutitijaroen, Panida

    2009-05-15

    This dissertation aims to address two optimization problems involving power system reliabilty analysis, namely multi-area power system adequacy planning and transformer maintenance optimization. A new simulation method for power system reliability...

  12. Reliability-based Design of Offshore Mooring Systems†

    E-Print Network [OSTI]

    Mousavi, Mir Emad

    2013-02-05

    This study proposes new methods for the reliability-based design of structural systems, with emphasis on offshore mooring systems. After a brief introduction to the mooring systems, two main objectives are discussed in this dissertation. The first...

  13. Automatic Reconfiguration for Large-Scale Reliable Storage Systems

    E-Print Network [OSTI]

    Rodrigues, Rodrigo

    Byzantine-fault-tolerant replication enhances the availability and reliability of Internet services that store critical state and preserve it despite attacks or software errors. However, existing Byzantine-fault-tolerant ...

  14. A Monte Carlo tool for multi-node reliability evaluation†

    E-Print Network [OSTI]

    Thalasila, Chander Pravin

    1993-01-01

    -Area Reliability Program(NARP) is based on the random sampling of generator and transmission line status for each hour. Monte Carlo Approach for Estimating Contingency Statistics along with the Evaluation Subroutine(MACS-ES) advances the generation...

  15. The reliability of a dialogue structure coding scheme.†

    E-Print Network [OSTI]

    Carletta, Jean; Isard, Amy; Isard, Stephen; Kowtko, Jacqueline C; Doherty-Sneddon, Gwyneth; Anderson, Anne H

    1997-01-01

    This papers describes the reliability of a dialogue structure coding scheme which is based on utterance function, game structure, and higher level transaction function, and which has been applied to a corpus of spontaneous ...

  16. 2012 CERTS Transmission Reliability R&D Internal Program Review...

    Office of Environmental Management (EM)

    Reliability R&D Internal Program Review June 12-13, 2012 LBNL Project Office 901 D St., SW Washington DC Nancy Lewis' cell: 510.918.3155 Revised Agenda: June 5, 2012 June 12, Day...

  17. FFTF (Fast Flux Test Facility) reactor shutdown system reliability reevaluation

    SciTech Connect (OSTI)

    Pierce, B.F.

    1986-07-01

    The reliability analysis of the Fast Flux Test Facility reactor shutdown system was reevaluated. Failure information based on five years of plant operating experience was used to verify original reliability numbers or to establish new ones. Also, system modifications made subsequent to performance of the original analysis were incorporated into the reevaluation. Reliability calculations and sensitivity analyses were performed using a commercially available spreadsheet on a personal computer. The spreadsheet was configured so that future failures could be tracked and compared with expected failures. A number of recommendations resulted from the reevaluation including both increased and decreased surveillance intervals. All recommendations were based on meeting or exceeding existing reliability goals. Considerable cost savings will be incurred upon implementation of the recommendations.

  18. Reliability assessment of electrical power systems using genetic algorithms†

    E-Print Network [OSTI]

    Samaan, Nader Amin Aziz

    2004-11-15

    The first part of this dissertation presents an innovative method for the assessment of generation system reliability. In this method, genetic algorithm (GA) is used as a search tool to truncate the probability state space ...

  19. High-reliability computing for the smarter planet

    SciTech Connect (OSTI)

    Quinn, Heather M [Los Alamos National Laboratory; Graham, Paul [Los Alamos National Laboratory; Manuzzato, Andrea [UNIV OF PADOVA; Dehon, Andre [UNIV OF PENN; Carter, Nicholas [INTEL CORPORATION

    2010-01-01

    The geometric rate of improvement of transistor size and integrated circuit performance, known as Moore's Law, has been an engine of growth for our economy, enabling new products and services, creating new value and wealth, increasing safety, and removing menial tasks from our daily lives. Affordable, highly integrated components have enabled both life-saving technologies and rich entertainment applications. Anti-lock brakes, insulin monitors, and GPS-enabled emergency response systems save lives. Cell phones, internet appliances, virtual worlds, realistic video games, and mp3 players enrich our lives and connect us together. Over the past 40 years of silicon scaling, the increasing capabilities of inexpensive computation have transformed our society through automation and ubiquitous communications. In this paper, we will present the concept of the smarter planet, how reliability failures affect current systems, and methods that can be used to increase the reliable adoption of new automation in the future. We will illustrate these issues using a number of different electronic devices in a couple of different scenarios. Recently IBM has been presenting the idea of a 'smarter planet.' In smarter planet documents, IBM discusses increased computer automation of roadways, banking, healthcare, and infrastructure, as automation could create more efficient systems. A necessary component of the smarter planet concept is to ensure that these new systems have very high reliability. Even extremely rare reliability problems can easily escalate to problematic scenarios when implemented at very large scales. For life-critical systems, such as automobiles, infrastructure, medical implantables, and avionic systems, unmitigated failures could be dangerous. As more automation moves into these types of critical systems, reliability failures will need to be managed. As computer automation continues to increase in our society, the need for greater radiation reliability is necessary. Already critical infrastructure is failing too frequently. In this paper, we will introduce the Cross-Layer Reliability concept for designing more reliable computer systems.

  20. Web Cube: a Programming Model for Reliable Web Applications

    E-Print Network [OSTI]

    Utrecht, Universiteit

    Web Cube: a Programming Model for Reliable Web Applications I.S.W.B. Prasetya, T.E.J. Vos, S UU-CS-2005-002 www.cs.uu.nl #12;Web Cube: a Programming Model for Reliable Web Applications I@cs.uu.nl, tanja@iti.upv.es, doaitse@cs.uu.nl, bela@cs.ui.ac.id Abstract Web Cube is a server side programming

  1. On-clip high frequency reliability and failure test structures

    DOE Patents [OSTI]

    Snyder, Eric S. (Albuquerque, NM); Campbell, David V. (Albuquerque, NM)

    1997-01-01

    Self-stressing test structures for realistic high frequency reliability characterizations. An on-chip high frequency oscillator, controlled by DC signals from off-chip, provides a range of high frequency pulses to test structures. The test structures provide information with regard to a variety of reliability failure mechanisms, including hot-carriers, electromigration, and oxide breakdown. The system is normally integrated at the wafer level to predict the failure mechanisms of the production integrated circuits on the same wafer.

  2. A Systematic and Comprehensive Tool for Software Reliability Modeling and Measurement

    E-Print Network [OSTI]

    Lyu, Michael R.

    reliability. This trend makes the estimation of software reliability more and more crit­ ical to most large­scale projects in their reliability engineering aspects. Traditionally, software reliability modeling is a setA Systematic and Comprehensive Tool for Software Reliability Modeling and Measurement Michael R

  3. Final Report for the Virtual Reliability Realization System LDRD

    SciTech Connect (OSTI)

    DELLIN, THEODORE A.; HENDERSON, CHRISTOPHER L.; O'TOOLE, EDWARD J.

    2000-12-01

    Current approaches to reliability are not adequate to keep pace with the need for faster, better and cheaper products and systems. This is especially true in high consequence of failure applications. The original proposal for the LDRD was to look at this challenge and see if there was a new paradigm that could make reliability predictions, along with a quantitative estimate of the risk in that prediction, in a way that was faster, better and cheaper. Such an approach would be based on the underlying science models that are the backbone of reliability predictions. The new paradigm would be implemented in two software tools: the Virtual Reliability Realization System (VRRS) and the Reliability Expert System (REX). The three-year LDRD was funded at a reduced level for the first year ($120K vs. $250K) and not renewed. Because of the reduced funding, we concentrated on the initial development of the expertise system. We developed an interactive semiconductor calculation tool needed for reliability analyses. We also were able to generate a basic functional system using Microsoft Siteserver Commerce Edition and Microsoft Sequel Server. The base system has the capability to store Office documents from multiple authors, and has the ability to track and charge for usage. The full outline of the knowledge model has been incorporated as well as examples of various types of content.

  4. NORTHWEST REGIONAL TECHNOLOGY CENTER

    E-Print Network [OSTI]

    NORTHWEST REGIONAL TECHNOLOGY CENTER for Homeland Security Northwest Regional Technology Center May 2015 | 1 AROUND THE REGION IN HOMELAND SECURITY The Northwest Regional Technology Center (NWRTC.S. Army Cyber Command; and Michael Echols, Director, Cyber Joint Program Management Office National

  5. Conservation Regional ConservationRegional Conservation

    E-Print Network [OSTI]

    Northwest Power and Conservation Council Regional ConservationRegional Conservation Update:Update?"" #12;slide 3 Northwest Power and Conservation Council PNW Energy Efficiency AchievementsPNW Energy Since 1978 Utility & BPASince 1978 Utility & BPA Programs, Energy Codes &Programs, Energy Codes

  6. NIST Organic Act National Institute of Standards and Technology Act

    E-Print Network [OSTI]

    Magee, Joseph W.

    -effectiveness. (2) Precise measurements, calibrations and standards help United States industry and manufacturingNIST Organic Act National Institute of Standards and Technology Act SECTION 1. FINDINGS and measurement standards needed to improve quality and reliability, and (B) new technological processes by which

  7. Topological organization of multi-chromosomal regions by Firre

    E-Print Network [OSTI]

    Hacisuleyman, Ezgi

    RNA, including long noncoding RNA (lncRNA), is known to be an abundant and important structural component of the nuclear matrix. However, the molecular identities, functional roles and localization dynamics of lncRNAs that ...

  8. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    building with PV, fuel cell, natural gas reciprocatingcombination of the following fuel cells as the main sources:

  9. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    diesel (Oil), 39-MW steam (Oil), 37-MW steam (coal/oil) CHP, 30-MW wind,Diesel Generators: two 55-kW (one of them with a controllable rectifier); microturbine MAGNETEK EG-50: 50-kW; wind

  10. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    Integration of Renewable Energy Sources and DistributedPower Grid with renewable Energy Resources Project Funded bypdf 2. Spanish Renewable Energy Review http://www.erec.org/

  11. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    2. RD&D Activities on Microgrids 2.1 US and Canada Country/Framework Programme): the Microgrids EU http://ec.europa.eu/Programme): More Microgrids EU http://ec.europa.eu/

  12. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    SciTech Connect (OSTI)

    Qu, Min; Marnay, Chris; Zhou, Nan

    2011-11-30

    This report collects and reviews policies and regulations related to microgrid development, and is intended as a reference. The material is divided into three parts under five dimensions: interconnection, RD&D, tariff policy, other policies, and recommendations.

  13. Program Program Organization Country Region Topic Sector Sector

    Open Energy Info (EERE)

    Technology characterizations Climate Energy Renewable Energy Economic Development Energy Efficiency Greenhouse Gas Grid Assessment and Integration Industry People and Policy...

  14. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    estimates an overall benefit of Ä 6 to Ä 11.9 billion, which is equivalent to a permanent reduction of electricity prices

  15. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    National Action Plan on Demand Response http://www.ferc.gov/e.g. by providing demand response and ancillary services,Action Plan on Demand Response (US): The Plan intends to

  16. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    cogeneration of a natural gas station (NGS). The micro-cogeneration systemgas reciprocating engine cogeneration, a thermal storage tank, storage batteries integrated into the building energy management system.

  17. Microgrid Policy Review of Selected Major Countries, Regions, and Organizations

    E-Print Network [OSTI]

    Qu, Min

    2014-01-01

    cogeneration of a natural gas station (NGS). The micro-cogeneration systemnatural gas reciprocating engine cogeneration, a thermal storage tank, storage batteries integrated into the building energy management system.

  18. Program Program Organization Country Region Topic Sector Sector

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg,Energy LLC JumpPhonoSolarProcessing andProduccion

  19. Ordered organic-organic multilayer growth

    DOE Patents [OSTI]

    Forrest, Stephen R; Lunt, Richard R

    2015-01-13

    An ordered multilayer crystalline organic thin film structure is formed by depositing at least two layers of thin film crystalline organic materials successively wherein the at least two thin film layers are selected to have their surface energies within .+-.50% of each other, and preferably within .+-.15% of each other, whereby every thin film layer within the multilayer crystalline organic thin film structure exhibit a quasi-epitaxial relationship with the adjacent crystalline organic thin film.

  20. Modular Operational Test Plans for Inferences on Software Reliability Based on a Markov Model

    E-Print Network [OSTI]

    Mazumdar, Mainak

    Modular Operational Test Plans for Inferences on Software Reliability Based on a Markov Model. Keywords: Software reliability; Modular Operational Tests; Sample Size Determination; Mathematical Programming #12;Modular Operational Test Plans for Inferences on Software Reliability Based on a Markov Model

  1. Reliability and Availability Requirements Engineering within the Unified Process using a

    E-Print Network [OSTI]

    Lutz, Robyn R.

    Reliability and Availability Requirements Engineering within the Unified Process using to support quantifiable, testable reliability and availability requirements (R&AR) elicitation, reliability and availability re- quirements, Unified Modeling Language profile, misuse cases, fault trees. I

  2. MEMS Reliability: Infrastructure, Test Structures, Experiments, and Failure Modes

    SciTech Connect (OSTI)

    TANNER,DANELLE M.; SMITH,NORMAN F.; IRWIN,LLOYD W.; EATON,WILLIAM P.; HELGESEN,KAREN SUE; CLEMENT,J. JOSEPH; MILLER,WILLIAM M.; MILLER,SAMUEL L.; DUGGER,MICHAEL T.; WALRAVEN,JEREMY A.; PETERSON,KENNETH A.

    2000-01-01

    The burgeoning new technology of Micro-Electro-Mechanical Systems (MEMS) shows great promise in the weapons arena. We can now conceive of micro-gyros, micro-surety systems, and micro-navigators that are extremely small and inexpensive. Do we want to use this new technology in critical applications such as nuclear weapons? This question drove us to understand the reliability and failure mechanisms of silicon surface-micromachined MEMS. Development of a testing infrastructure was a crucial step to perform reliability experiments on MEMS devices and will be reported here. In addition, reliability test structures have been designed and characterized. Many experiments were performed to investigate failure modes and specifically those in different environments (humidity, temperature, shock, vibration, and storage). A predictive reliability model for wear of rubbing surfaces in microengines was developed. The root causes of failure for operating and non-operating MEMS are discussed. The major failure mechanism for operating MEMS was wear of the polysilicon rubbing surfaces. Reliability design rules for future MEMS devices are established.

  3. Relationship between Compost Stability and Extractable Organic Carbon L. Wu and L. Q. Ma*

    E-Print Network [OSTI]

    Ma, Lena

    Relationship between Compost Stability and Extractable Organic Carbon L. Wu and L. Q. Ma* ABSTRACT to the factEstablishing a simple yet reliable compost stability test is essential that NaOH-extractable organic carbon (OC) containsfor a better compost quality control and utilization efficiency. The objective

  4. A Methodology to Assess the Reliability of Hydrogen-based Transportation Energy Systems

    E-Print Network [OSTI]

    McCarthy, Ryan

    2004-01-01

    2. Define reliability in hydrogen energy systems 3.metrics to value reliability in hydrogen energy systems 4.Specify hydrogen energy systems to evaluate 5. Develop

  5. Comprehensive Regional Goods Movement Plan and Implementation Strategy

    E-Print Network [OSTI]

    California at Davis, University of

    Comprehensive Regional Goods Movement Plan and Implementation Strategy ON THE MOVE Southern? Nation's largest Metropolitan Planning Organization (MPO) and Council of Governments (COG) 6 counties and Warehousing, $22 Utilities, $10 Mining, $3 Forestry, Fishing, Related Activities and Other, $- 4 Manufacturing

  6. Regional Research Collaborations

    E-Print Network [OSTI]

    Regional Research Collaborations Merrill Series on The Research Mission of Public Universities at Birmingham Regional Neuroscience Research Collaboration: The Alabama Experience Panel 1: Research ........................................................................................................5 Vice Chancellor for Research, University of Kansas Medical Center Evolution of Reproductive

  7. DAKOTA reliability methods applied to RAVEN/RELAP-7.

    SciTech Connect (OSTI)

    Swiler, Laura Painton; Mandelli, Diego; Rabiti, Cristian; Alfonsi, Andrea

    2013-09-01

    This report summarizes the result of a NEAMS project focused on the use of reliability methods within the RAVEN and RELAP-7 software framework for assessing failure probabilities as part of probabilistic risk assessment for nuclear power plants. RAVEN is a software tool under development at the Idaho National Laboratory that acts as the control logic driver and post-processing tool for the newly developed Thermal-Hydraulic code RELAP-7. Dakota is a software tool developed at Sandia National Laboratories containing optimization, sensitivity analysis, and uncertainty quantification algorithms. Reliability methods are algorithms which transform the uncertainty problem to an optimization problem to solve for the failure probability, given uncertainty on problem inputs and a failure threshold on an output response. The goal of this work is to demonstrate the use of reliability methods in Dakota with RAVEN/RELAP-7. These capabilities are demonstrated on a demonstration of a Station Blackout analysis of a simplified Pressurized Water Reactor (PWR).

  8. Sprinkler: A reliable and energy efficient data dissemination service for extreme scale wireless networks of embedded devices

    E-Print Network [OSTI]

    Naik, Vinayak; Arora, Anish; Sinha, Prasun; Zhang, Hongwei

    2007-01-01

    A RELIABLE AND ENERGY EFFICIENT DATA DISSEMINATION SERVICEA RELIABLE AND ENERGY EFFICIENT DATA DISSEMINATION SERVICEA Reliable and Energy Efficient Data Dissemination Service

  9. Northwest Regional Technology Center

    E-Print Network [OSTI]

    management and public safety professionals to define and prioritize technology needs. Coordinate and leadNorthwest Regional Technology Center for Homeland Security The Northwest Regional Technology Center and deployment of technologies that are effective homeland security solutions for the region, and accelerate

  10. Reliability-based condition assessment of steel containment and liners

    SciTech Connect (OSTI)

    Ellingwood, B.; Bhattacharya, B.; Zheng, R.

    1996-11-01

    Steel containments and liners in nuclear power plants may be exposed to aggressive environments that may cause their strength and stiffness to decrease during the plant service life. Among the factors recognized as having the potential to cause structural deterioration are uniform, pitting or crevice corrosion; fatigue, including crack initiation and propagation to fracture; elevated temperature; and irradiation. The evaluation of steel containments and liners for continued service must provide assurance that they are able to withstand future extreme loads during the service period with a level of reliability that is sufficient for public safety. Rational methodologies to provide such assurances can be developed using modern structural reliability analysis principles that take uncertainties in loading, strength, and degradation resulting from environmental factors into account. The research described in this report is in support of the Steel Containments and Liners Program being conducted for the US Nuclear Regulatory Commission by the Oak Ridge National Laboratory. The research demonstrates the feasibility of using reliability analysis as a tool for performing condition assessments and service life predictions of steel containments and liners. Mathematical models that describe time-dependent changes in steel due to aggressive environmental factors are identified, and statistical data supporting the use of these models in time-dependent reliability analysis are summarized. The analysis of steel containment fragility is described, and simple illustrations of the impact on reliability of structural degradation are provided. The role of nondestructive evaluation in time-dependent reliability analysis, both in terms of defect detection and sizing, is examined. A Markov model provides a tool for accounting for time-dependent changes in damage condition of a structural component or system. 151 refs.

  11. Human Reliability Analysis for Digital Human-Machine Interfaces

    SciTech Connect (OSTI)

    Ronald L. Boring

    2014-06-01

    This paper addresses the fact that existing human reliability analysis (HRA) methods do not provide guidance on digital human-machine interfaces (HMIs). Digital HMIs are becoming ubiquitous in nuclear power operations, whether through control room modernization or new-build control rooms. Legacy analog technologies like instrumentation and control (I&C) systems are costly to support, and vendors no longer develop or support analog technology, which is considered technologically obsolete. Yet, despite the inevitability of digital HMI, no current HRA method provides guidance on how to treat human reliability considerations for digital technologies.

  12. Product acceptance environmental and destructive testing for reliability.

    SciTech Connect (OSTI)

    Dvorack, Michael A.; Kerschen, Thomas J.; Collins, Elmer W.

    2007-08-01

    To determine whether a component is meeting its reliability requirement during production, acceptance sampling is employed in which selected units coming off the production line are subjected to additional environmental and/or destructive tests that are within the normal environment space to which the component is expected to be exposed throughout its life in the Stockpile. This report describes what these tests are and how they are scored for reliability purposes. The roles of screens, Engineering Use Only tests, and next assembly product acceptance testing are also discussed, along with both the advantages and disadvantages of environmental and destructive testing.

  13. Technical information report: Plasma melter operation, reliability, and maintenance analysis

    SciTech Connect (OSTI)

    Hendrickson, D.W. [ed.

    1995-03-14

    This document provides a technical report of operability, reliability, and maintenance of a plasma melter for low-level waste vitrification, in support of the Hanford Tank Waste Remediation System (TWRS) Low-Level Waste (LLW) Vitrification Program. A process description is provided that minimizes maintenance and downtime and includes material and energy balances, equipment sizes and arrangement, startup/operation/maintence/shutdown cycle descriptions, and basis for scale-up to a 200 metric ton/day production facility. Operational requirements are provided including utilities, feeds, labor, and maintenance. Equipment reliability estimates and maintenance requirements are provided which includes a list of failure modes, responses, and consequences.

  14. Energy Regulation, Roll Call Votes and Regional Resources: Evidence from Russia

    E-Print Network [OSTI]

    Grigoriadis, Theocharis N; Torgler, Benno

    2007-01-01

    Problems of the North 20. Regulation and Work organizationV. "Reform and Regulation of Natural Monopolies." (InEnergy Regulation, Roll Call Votes and Regional Resources:

  15. REGIONAL PARTNERSHIP NEWS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    passion, combined with an impressive vision for Technology 2020. He impressed the search committee and the staff with his ideas for and commit- ment to moving the organization...

  16. Organic Photovoltaics Philip Schulz

    E-Print Network [OSTI]

    Firestone, Jeremy

    Field Effect Transistors Organic Light Emitting Diodes Organic Solar Cells .OFET, OTFT .RF-ID tag 1977 ≠ Conductivity in polymers 1986 ≠ First heterojunction OPV 1987 ≠ First organic light emitting diode (OLED) 1993 ≠ First OPV from solution processing 2001 ≠ First certified organic solar cell with 2

  17. Departmental Organization and Management

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1993-06-10

    Effective immediately, the Departmental organization structure reflected in the chart at Attachment 1 has been approved.

  18. 1 INTRODUCTION Rational and reliable seismic design theories and

    E-Print Network [OSTI]

    Spencer Jr., Billie F.

    to the seismic design of dams to be constructed and the assessment of earthquake safety of existing dams. Many is not almost considered in the seismic design of dams to be constructed and the assessment of earthquake safety1 INTRODUCTION Rational and reliable seismic design theories and analytical methods are substantial

  19. Automated Energy Distribution and Reliability System (AEDR): Final Report

    SciTech Connect (OSTI)

    Buche, D. L.

    2008-07-01

    This report describes Northern Indiana Public Service Co. project efforts to develop an automated energy distribution and reliability system. The purpose of this project was to implement a database-driven GIS solution that would manage all of the company's gas, electric, and landbase objects.

  20. Tools and Techniques for Ensuring Automotive EMC Performance and Reliability

    E-Print Network [OSTI]

    Stuart, Steven J.

    V-Model 4 Concept Design Design Requirements Detailed Design and Modeling Prototype System Validation System Integration Component Verification #12;AUTOSAR 5 APPLICATION SOFTWARE HARDWARE AUTOSAR powerful More efficient Far more reliable. Cars with intelligently designed electronic systems will be: 9

  1. The Ambient Computational Environments Architecture for Reliable, Secure,

    E-Print Network [OSTI]

    Kansas, University of

    challenge. The ACE - Ambient Computational Environments - architecture aims at high- scale and seamlessThe Ambient Computational Environments Architecture for Reliable, Secure, and Pervasive Computing The University of Kansas #12;Abstract During the past few years, the technology world has become more and more

  2. User-Level Reliability Monitoring in Urban Personal

    E-Print Network [OSTI]

    Calgary, University of

    TAKALA, Senior Member, IEEE Tampere University of Technology Finland Monitoring the reliability University of Technology, Tampere, Finland. 0018-9251/07/$25.00 cį 2007 IEEE I. INTRODUCTION To ensure a user University of Technology Finland ANDREAS WIESER G īERARD LACHAPELLE, Member, IEEE University of Calgary JARMO

  3. A TECHNIQUE FOR TESTING HIGHLY RELIABLE REAL-TIME SOFTWARE

    E-Print Network [OSTI]

    Bieman, James M.

    Task Plan ģ A TECHNIQUE FOR TESTING HIGHLY RELIABLE REAL-TIME SOFTWARE Slide Presentation Biography that uses executable specifications based on Annotated Ada (Anna) for software testing in hard real process and does not interfere with the software under test. 1.0 INTRODUCTION Automating the verification

  4. SOFTWARE TESTING, VERIFICATION AND RELIABILITY Softw. Test. Verif. Reliab. (2014)

    E-Print Network [OSTI]

    2014-01-01

    SOFTWARE TESTING, VERIFICATION AND RELIABILITY Softw. Test. Verif. Reliab. (2014) Published online. INTRODUCTION As software evolves, engineers regression test it to validate new features and detect whether new in Wiley Online Library (wileyonlinelibrary.com). DOI: 10.1002/stvr.1562 Directed test suite augmentation

  5. On some statistical aspects of software testing and reliability

    E-Print Network [OSTI]

    Coolen, Frank

    On some statistical aspects of software testing and reliability Frank P.A. Coolen Abstract This article discusses the author's views on possible contributions statistics can make to software testing, the mes- sage is that statistical methods cannot provide proper support for software testing or provide

  6. LMS: A Router Assisted Scheme for Reliable Multicast Christos Papadopoulos

    E-Print Network [OSTI]

    Papadopoulos, Christos

    1 LMS: A Router Assisted Scheme for Reliable Multicast Christos Papadopoulos University of Southern≠weight Multicast Ser≠ vices (LMS), which enhance the existing multicast model with simple forwarding services that do not require transport level actions. Using LMS, routers tag and steer transport≠level control

  7. Reliable data collection in highly disconnected environments using mobile phones

    E-Print Network [OSTI]

    Parikh, Tapan S.

    high-impact applications for these environments. Many of the applications built with CAM have relied information and get the collected data backed up on reliable media. We propose extending CAM's networking volunteers to resurvey - a waste of both time and resources. There was a clear need to move the data

  8. Action potentials reliably invade axonal arbors of rat neocortical neurons

    E-Print Network [OSTI]

    Tank, David

    Action potentials reliably invade axonal arbors of rat neocortical neurons Charles L. Cox* , Winfried Denkß , David W. Tankß , and Karel Svoboda*∂ *Howard Hughes Medical Institute, Cold Spring Harbor, Murray Hill, NJ 07974 Communicated by James D. Watson, Cold Spring Harbor Laboratory, Cold Spring Harbor

  9. SDRT: A Reliable Data Transport Protocol for Underwater Sensor Networks

    E-Print Network [OSTI]

    Cui, Jun-Hong

    activities such as scientific exploration and commercial exploitation, underwater sensor networks empower us networks, for mission critical applications, reliable data transport is demanded in under- water sensor channels is limited and depends on both transmission range and frequency [8], [24], [5], [6]. According

  10. Towards Reliable 5Gbps Wave-pipelined and

    E-Print Network [OSTI]

    Lemieux, Guy

    Towards Reliable 5Gbps Wave-pipelined and 3Gbps Surfing Interconnect in 65nm FPGAs Paul Teehan Guy source Data destination Input switches Output switches High-speed pipelined wire Regular interconnect-speed pipelined wire #12;FPGA'09 4 of 27 Key points Base design Wave pipelining, source synchronous timing

  11. Fault-Tolerant and Reliable Computation in Cloud Computing

    E-Print Network [OSTI]

    Deng, Jing

    Fault-Tolerant and Reliable Computation in Cloud Computing Jing Deng Scott C.-H. Huang Yunghsiang S, Taipei, 106 Taiwan. ß Intelligent Automation, Inc., Rockville, MD, USA. Abstract-- Cloud computing of scientific computation in cloud computing. We investigate a cloud selection strategy to decompose the matrix

  12. EE 850.3 (3L) Reliability Engineering

    E-Print Network [OSTI]

    Saskatchewan, University of

    EE 850.3 (3L) Reliability Engineering Department of Electrical and Computer Engineering Fall 2014 Karki, Ph.D., P.Eng. Associate Professor, Department of Electrical and Computer Engineering Office: Room 3B30, Engineering Building Phone: (306) 966-5384 Email: rajesh.karki@usask.ca Lectures: Monday

  13. reliable, efficient, ultra-clean Fuel Cell Power Plant Experience

    E-Print Network [OSTI]

    reliable, efficient, ultra-clean Fuel Cell Power Plant Experience Naval Applications US Department Shore Capacity - Low Profile, Easy Siting Connects to existing electricity and fuel infrastructure Cell Stack and operated with high sulfur naval logistic fuel (JP-5 jet fuel) ∑ Over 1000 Hours of Fuel

  14. IDENTIFICATION OF RELIABLE PREDICTOR MODELS FOR UNKNOWN SYSTEMS: A

    E-Print Network [OSTI]

    Campi, Marco

    IDENTIFICATION OF RELIABLE PREDICTOR MODELS FOR UNKNOWN SYSTEMS: A DATA-CONSISTENCY APPROACH BASED mechanism ≠ DGM), a selected family of models, with which we want to describe the observed data (the data, that is a statement of probability that the computed model will be consistent with future unknown data. Keywords

  15. SPEAR fuel reliability code system. General description. [PWR; BWR

    SciTech Connect (OSTI)

    Christensen, R.

    1980-03-01

    A general description is presented for the SPEAR fuel reliability code system. Included is a discussion of the methodology employed and the structure of the code system, as well as discussion of the major components: the data preparation routines, the mechanistic fuel performance model, the mechanistic cladding failure model, and the statistical failure model.

  16. Hidden Challenges to MEMS Commercialization: Design Realization and Reliability Assurance

    SciTech Connect (OSTI)

    McWhorter, P.J.; Miller, S.L.; Miller, W.M.; Rodger, M.S.; Yarberry, V.R.

    1999-01-20

    The successful commercialization of MicroElectroMechanical Systems (MEMS) is an essential prerequisite for their implementation in many critical government applications. Several unique challenges must be overcome to achieve this widespread commercialization. Challenges associated with design realization and reliability assurance are discussed, along with approaches taken by Sandia to successfully overcome these challenges.

  17. Saving power without compromising disk drive reliability Xenia Mountrouidou

    E-Print Network [OSTI]

    Butt, Ali R.

    Saving power without compromising disk drive reliability Xenia Mountrouidou College of William intervals for power savings within strict constraints: first, it is imperative to contain the delays in service of IO requests that occur during power savings since the time to bring up the disk

  18. WIND POWER SIMULATION MODEL FOR RELIABILITY EVALUATION Rajesh Karki

    E-Print Network [OSTI]

    Saskatchewan, University of

    WIND POWER SIMULATION MODEL FOR RELIABILITY EVALUATION Rajesh Karki Rajesh.Karki@usask.ca Po Hu poh The rapidly increasing contribution of wind power to electric power generation around the world has motivated a need to develop more widely applicable methodologies for evaluating the actual benefits of adding wind

  19. Composite System based Multi-Area Reliability Evaluation†

    E-Print Network [OSTI]

    Nagarajan, Ramya

    2011-02-22

    and no - load loss sharing policy among the areas. The proposed method is applied to standard IEEE 24 bus Reliability Test System (RTS) and the traditional equivalent tie-line method is applied to the multi-area configuration of the same test system. The results...

  20. Improving Work Flow Reliability Proceedings IGLC-7 275

    E-Print Network [OSTI]

    Tommelein, Iris D.

    , load, productivity, project planning and control, reliability, throughput, variability. 1 Director driven for speed. The production plans of upstream PUs is one source of information regarding work flow to significantly improve project performance because it allows the application of planning to production. If you

  1. Reliability Tradeoffs in Personal Storage Systems John A. Chandy

    E-Print Network [OSTI]

    Chandy, John A.

    Reliability Tradeoffs in Personal Storage Systems John A. Chandy john.chandy@uconn.edu Sumit processes. These methods are most useful in storage systems where complete data protection or availability Disk arrays have long been used to improve the performance of storage systems [5, 10]. The parallelism

  2. IEEE TRANSACTIONS ON RELIABILITY 1 Optimal Maintenance Strategies for Wind

    E-Print Network [OSTI]

    Ntaimo, Lewis

    conditions. In-situ sensors installed at wind turbines produce useful information about the physical guidelines that reduces the repair costs and increases the marketability of wind energy generation. #12;IEEEIEEE TRANSACTIONS ON RELIABILITY 1 Optimal Maintenance Strategies for Wind Turbine Systems Under

  3. Toward Reliable and Efficient Reporting in Wireless Sensor Networks

    E-Print Network [OSTI]

    Boutaba, Raouf

    Bouabdallah, and Raouf Boutaba, Senior Member, IEEE Abstract--Energy efficiency is one of the major concerns and as the first main contribution, we derive the optimal number of reporting nodes Nopt energy that minimizes the energy consumed to report reliably the occurrence of an event. In other words, we prove that limiting

  4. Reliable and Scalable Communication for the Power Grid

    E-Print Network [OSTI]

    Mueller, Frank

    Reliable and Scalable Communication for the Power Grid Christopher Zimmer, Frank Mueller Abstract Future smart power grids require constant data availability for actuation of control decisions. The job topologies of smart devices that enable multi-route discovery in an intelligent power grid. This is ac

  5. Validity and Reliability of Web Accessibility Guidelines Giorgio Brajnik

    E-Print Network [OSTI]

    Brajnik, Giorgio

    checkpoints taken from WCAG 1.0 and WCAG 2.0. The experiment employed 35 young web developers with some the viewpoint of their validity and reliability. WCAG 2.0 explicitly claim that they are based on "testable knowledge on web accessibility. Although this is a small-scale experiment, unlikely to provide definite

  6. Hierarchical Reliable Multicast: performance analysis and placement of proxies

    E-Print Network [OSTI]

    Tobagi, Fouad

    the term Hierarchical Reliable Multicast (HRM). For each subgroup, there is a designated node, the proxy and its loss characteristics. Furthermore, the performance of the HRM approach, in particular, strongly model the HRM problem, then define and compute appropriate performance metrics and finally give insights

  7. RF-MEMS capacitive switches with high reliability

    DOE Patents [OSTI]

    Goldsmith, Charles L.; Auciello, Orlando H.; Carlisle, John A.; Sampath, Suresh; Sumant, Anirudha V.; Carpick, Robert W.; Hwang, James; Mancini, Derrick C.; Gudeman, Chris

    2013-09-03

    A reliable long life RF-MEMS capacitive switch is provided with a dielectric layer comprising a "fast discharge diamond dielectric layer" and enabling rapid switch recovery, dielectric layer charging and discharging that is efficient and effective to enable RF-MEMS switch operation to greater than or equal to 100 billion cycles.

  8. Using data fusion for scoring reliability of proteinprotein interactions

    E-Print Network [OSTI]

    Wong, Limsoon

    Using data fusion for scoring reliability of protein≠protein interactions Alireza Vazifedoost@ut.ac.ir **Rahgozar@ut.ac.ir moshiri@ut.ac.ir sadeghi@nigeb.ac.ir ß ß hnchua@i2r.a-star.edu.sg ∂∂ skng@i2r.a-star data fusion to model potential interactions between the multiple information sources. Using data fusion

  9. Transformer Thermal Modeling: Improving Reliability Using Data Quality Control

    E-Print Network [OSTI]

    1 Transformer Thermal Modeling: Improving Reliability Using Data Quality Control Daniel J. Tylavsky--Eventually all large transformers will be dynamically loaded using models updated regularly from field measured data. Models obtained from measured data give more accurate results than models based on transformer

  10. System Reliability Analysis of an Nversion Programming Application

    E-Print Network [OSTI]

    Lyu, Michael R.

    reliability anal≠ ysis of a system designed to tolerate both hardware and software faults. The system being hardware. The analysis of the system considers independent soft≠ ware faults, related software faults, transient hardware faults, permanent hardware faults, and imperfect cov≠ erage. The overall model

  11. Continuously Optimized Reliable Energy (CORE) Microgrid: Models & Tools (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2013-07-01

    This brochure describes Continuously Optimized Reliable Energy (CORE), a trademarked process NREL employs to produce conceptual microgrid designs. This systems-based process enables designs to be optimized for economic value, energy surety, and sustainability. Capabilities NREL offers in support of microgrid design are explained.

  12. What makes information valuable: signal reliability and environmental uncertainty

    E-Print Network [OSTI]

    Stephens, David W.

    uncertainty in animal signal use. We de- veloped a simple model that predicted when animals should switch The Association for the Study of Animal Behaviour. Published by Elsevier Ltd. All rights reserved. Many aspects. An example of a reliable signal is the carotenoid-based plumage colora- tion in male house finches

  13. Reliability and Throughput in Future Automotive Communication Networks

    E-Print Network [OSTI]

    Rajkumar, Ragunathan "Raj"

    Reliability and Throughput in Future Automotive Communication Networks John Liu, Timothy TaltyStar. This action created a new industry called automotive telematics, helping to save lives and providing, the automotive telematics industry has experienced a healthy growth in North America. During the current economic

  14. Accident Sequence Evaluation Program: Human reliability analysis procedure

    SciTech Connect (OSTI)

    Swain, A.D.

    1987-02-01

    This document presents a shortened version of the procedure, models, and data for human reliability analysis (HRA) which are presented in the Handbook of Human Reliability Analysis With emphasis on Nuclear Power Plant Applications (NUREG/CR-1278, August 1983). This shortened version was prepared and tried out as part of the Accident Sequence Evaluation Program (ASEP) funded by the US Nuclear Regulatory Commission and managed by Sandia National Laboratories. The intent of this new HRA procedure, called the ''ASEP HRA Procedure,'' is to enable systems analysts, with minimal support from experts in human reliability analysis, to make estimates of human error probabilities and other human performance characteristics which are sufficiently accurate for many probabilistic risk assessments. The ASEP HRA Procedure consists of a Pre-Accident Screening HRA, a Pre-Accident Nominal HRA, a Post-Accident Screening HRA, and a Post-Accident Nominal HRA. The procedure in this document includes changes made after tryout and evaluation of the procedure in four nuclear power plants by four different systems analysts and related personnel, including human reliability specialists. The changes consist of some additional explanatory material (including examples), and more detailed definitions of some of the terms. 42 refs.

  15. Modeling Stochastic Correlated Failures and their Effects on Network Reliability

    E-Print Network [OSTI]

    Hayat, Majeed M.

    in this field have used this concept to generate geographically correlated failures (e.g. [1] and [2]). SomeModeling Stochastic Correlated Failures and their Effects on Network Reliability Mahshid Rahnamay--The physical infrastructure of communication net- works is vulnerable to spatially correlated failures arising

  16. Reliable Contracts for Unreliable Half-Duplex Communications

    E-Print Network [OSTI]

    Doyen, Laurent

    indicate useful criteria for the design of WSDL. We moreover establish a polynomial-time complexity explains the criteria proposed by Stengel and Bultan for Sing# contracts to be reliable, and possibly. The primary goal of session types is to ensure type-safety, e.g. that communications over a typed channel

  17. WEST COAST REGIONAL CARBON SEQUESTRATION PARTNERSHIP

    SciTech Connect (OSTI)

    Larry Myer; Terry Surles; Kelly Birkinshaw

    2004-01-01

    The West Coast Regional Carbon Sequestration Partnership is one of seven partnerships which have been established by the US Department of Energy (DOE) to evaluate carbon dioxide capture, transport and sequestration (CT&S) technologies best suited for different regions of the country. The West Coast Region comprises Arizona, California, Nevada, Oregon, Washington, and the North Slope of Alaska. Led by the California Energy Commission, the West Coast Partnership is a consortium of over thirty five organizations, including state natural resource and environmental protection agencies; national labs and universities; private companies working on CO{sub 2} capture, transportation, and storage technologies; utilities; oil and gas companies; nonprofit organizations; and policy/governance coordinating organizations. In an eighteen month Phase I project, the Partnership will evaluate both terrestrial and geologic sequestration options. Work will focus on five major objectives: (1) Collect data to characterize major CO{sub 2} point sources, the transportation options, and the terrestrial and geologic sinks in the region, and compile and organize this data via a geographic information system (GIS) database; (2) Address key issues affecting deployment of CT&S technologies, including storage site permitting and monitoring, injection regulations, and health and environmental risks (3) Conduct public outreach and maintain an open dialogue with stakeholders in CT&S technologies through public meetings, joint research, and education work (4) Integrate and analyze data and information from the above tasks in order to develop supply curves and cost effective, environmentally acceptable sequestration options, both near- and long-term (5) Identify appropriate terrestrial and geologic demonstration projects consistent with the options defined above, and create action plans for their safe and effective implementation A kickoff meeting for the West Coast Partnership was held on Sept 30-Oct.1. Contracts were then put into place with twelve organizations which will carry out the technical work required to meet Partnership objectives.

  18. Models for Battery Reliability and Lifetime: Applications in Design and Health Management (Presentation)

    SciTech Connect (OSTI)

    Smith, K.; Neubauer, J.; Wood, E.; Jun, M.; Pesaran, A.

    2013-06-01

    This presentation discusses models for battery reliability and lifetime and the Battery Ownership Model.

  19. Automated Modeling of Dynamic Reliability Block Diagrams Using Colored Petri Nets

    E-Print Network [OSTI]

    Xu, Haiping

    solution to automated verification of DRBD models. Index Terms--System reliability, reliability block \\ Abstract--Computer system reliability is conventionally modeled and analyzed using techniques such as fault), defines a framework for modeling dynamic reliability behavior of computer-based systems. However

  20. Added Value of Reliability to a Microgrid: Simulations of Three California Buildings

    E-Print Network [OSTI]

    Marnay, Chris

    2009-01-01

    distributed generation, real options analysis of renewable energyDelivery and Energy Reliability, Renewable and Distributed

  1. Thermal Performance and Reliability of Bonded Interfaces for Power Electronics Packaging Applications (Presentation)

    SciTech Connect (OSTI)

    Devoto, D.

    2013-07-01

    This presentation discusses the thermal performance and reliability of bonded interfaces for power electronics packaging applications.

  2. Racing to Success 2005 Southern Region Water Quality Conference

    E-Print Network [OSTI]

    AE06-11 Racing to Success 2005 Southern Region Water Quality Conference Lexington, Kentucky. It was the tenth biennial conference organized and conducted by the Southern Region Water Quality Planning area provided the framework for the conference. A description of these 12 programs in addition to much

  3. IEEE TRANSACTIONS ON RELIABILITY, VOL. 49, NO. 1, MARCH 2000 37 Failure Correlation in Software Reliability Models

    E-Print Network [OSTI]

    Goseva-Popstojanova, Katerina

    property of the developed Markov renewal modeling approach is its flexibility. It allows con- struction the analysis either on Markov chain theory or on renewal process theory. Thus, our modeling approach Reliability Models Katerina Goseva-Popstojanova, Member, IEEE, and Kishor S. Trivedi, Fellow, IEEE Abstract

  4. Characterization of Siberian Arctic coastal sediments: Implications for terrestrial organic carbon export

    E-Print Network [OSTI]

    Guo, Laodong

    pyrolysis-GC/MS of the sedimentary organic carbon (SOC) indicated an increase in the freshness for carbon. As such, large quantities of soil organic carbon are stored in the region. It is estimated

  5. Mixed crystal organic scintillators

    DOE Patents [OSTI]

    Zaitseva, Natalia P; Carman, M Leslie; Glenn, Andrew M; Hamel, Sebastien; Hatarik, Robert; Payne, Stephen A; Stoeffl, Wolfgang

    2014-09-16

    A mixed organic crystal according to one embodiment includes a single mixed crystal having two compounds with different bandgap energies, the organic crystal having a physical property of exhibiting a signal response signature for neutrons from a radioactive source, wherein the signal response signature does not include a significantly-delayed luminescence characteristic of neutrons interacting with the organic crystal relative to a luminescence characteristic of gamma rays interacting with the organic crystal. According to one embodiment, an organic crystal includes bibenzyl and stilbene or a stilbene derivative, the organic crystal having a physical property of exhibiting a signal response signature for neutrons from a radioactive source.

  6. Clean Energy Manufacturing Initiative Southeast Regional Summit

    Broader source: Energy.gov [DOE]

    Registration is now open for the Clean Energy Manufacturing Initiativeís (CEMI) Southeast Regional Summit! The all-day conference, hosted by the U.S. Department of Energy (DOE), will take place on July 9 in Atlanta, Georgia, at the Renaissance Atlanta Midtown Hotel. The Southeast Regional Summit will bring together leaders from industry, academia, and government to focus on competitiveness and innovation in clean energy manufacturing throughout the southeastern United States. The Summit is the third in a series organized around the country, and will convene key stakeholders to:

  7. Load As A Reliability Resource in the Restructured Electricity Market

    SciTech Connect (OSTI)

    Kueck, J.D.

    2002-06-10

    Recent electricity price spikes are painful reminders of the value that meaningful demand-side responses could bring to the restructuring US electricity system. Review of the aggregate offers made by suppliers confirms that even a modest increase in demand elasticity could dramatically reduce these extremes in price volatility. There is a strong need for dramatically increased customer participation in these markets to enhance system reliability and reduce price volatility. Indeed, allowing customers to manage their loads in response to system conditions might be thought of as the ultimate reliability resource. Most would agree that meaningful demand-side responses to price are the hallmark of a well-functioning competitive market [1]. Yet, in today's markets for electricity, little or no such response is evident. The reason is simple: customers currently do not experience directly the time-varying costs of their consumption decisions. Consequently, they have no incentive to modify these decisions in ways that might enhance system reliability or improve the efficiency of the markets in which electricity is traded. Increased customer participation is a necessary step in the evolution toward more efficient markets for electricity and ancillary services. This scoping report provides a three-part assessment of the current status of efforts to enhance the ability of customer's load to participate in competitive markets with a specific focus on the role of customer loads in enhancing electricity system reliability. First, this report considers the definitions of electricity-reliability-enhancing ancillary services (Section 2) and a preliminary assessment of the ability of customer's loads to provide these services. Second, is a review a variety of programs in which load has been called on as a system reliability resource (Section 3). These experiences, drawn from both past and current utility and ISO programs, focus on programs triggered by system condition (e.g., forecast reserves fall below a threshold), rather than those triggered by price (e.g., real-time prices). Third, the report examines the status of the underlying metering, communication, and control technologies required to enable customer loads to participate in competitive electricity markets (Section 4). Following the three-part assessment, we offer preliminary thoughts on directions for future research (Section 5).

  8. Challenges for improving estimates of soil organic carbon stored...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Challenges for improving estimates of soil organic carbon stored in permafrost regions September 30, 2013 Tweet EmailPrint One of the greatest environmental challenges of the 21st...

  9. Regional Public Coordination Transportation Plan Texoma Region #22†

    E-Print Network [OSTI]

    Texoma Council of Governments

    2006-12-01

    .......................................................................................................... 6 Regional Geography and Demographics..................................................................................... 6 Regional Agencies Responsible for Transportation Planning.................................................. 6 Descriptions... of the Region?s Public Transportation Providers................................................. 7 Coordinated Transportation Plan..................................................................................................... 8 Coordination Actions...

  10. Regional Analysis Briefs

    Reports and Publications (EIA)

    2028-01-01

    Regional Analysis Briefs (RABs) provide an overview of specific regions that play an important role in world energy markets, either directly or indirectly. These briefs cover areas that are currently major producers (Caspian Sea), have geopolitical importance (South China Sea), or may have future potential as producers or transit areas (East Africa, Eastern Mediterranean).

  11. Organic photovoltaics and concentrators

    E-Print Network [OSTI]

    Mapel, Jonathan King

    2008-01-01

    The separation of light harvesting and charge generation offers several advantages in the design of organic photovoltaics and organic solar concentrators for the ultimate end goal of achieving a lower cost solar electric ...

  12. Industrial Organization in China: A Case Study of Foxconn's Factory Relocations

    E-Print Network [OSTI]

    Cai, Siyu

    2012-01-01

    Scott, Allen J. 1986. ďIndustrial Organization and Location:Institutional Change, and Industrial Location: EconomicTransition and Industrial Concentration in China" Regional

  13. Integrated approach to economical, reliable, safe nuclear power production

    SciTech Connect (OSTI)

    Not Available

    1982-06-01

    An Integrated Approach to Economical, Reliable, Safe Nuclear Power Production is the latest evolution of a concept which originated with the Defense-in-Depth philosophy of the nuclear industry. As Defense-in-Depth provided a framework for viewing physical barriers and equipment redundancy, the Integrated Approach gives a framework for viewing nuclear power production in terms of functions and institutions. In the Integrated Approach, four plant Goals are defined (Normal Operation, Core and Plant Protection, Containment Integrity and Emergency Preparedness) with the attendant Functional and Institutional Classifications that support them. The Integrated Approach provides a systematic perspective that combines the economic objective of reliable power production with the safety objective of consistent, controlled plant operation.

  14. Reliability estimates for selected sensors in fusion applications

    SciTech Connect (OSTI)

    Cadwallader, L.C.

    1996-09-01

    This report presents the results of a study to define several types of sensors in use, the qualitative reliability (failure modes) and quantitative reliability (average failure rates) for these types of process sensors. Temperature, pressure, flow, and level sensors are discussed for water coolant and for cryogenic coolants. The failure rates that have been found are useful for risk assessment and safety analysis. Repair times and calibration intervals are also given when found in the literature. All of these values can also be useful to plant operators and maintenance personnel. Designers may be able to make use of these data when planning systems. The final chapter in this report discusses failure rates for several types of personnel safety sensors, including ionizing radiation monitors, toxic and combustible gas detectors, humidity sensors, and magnetic field sensors. These data could be useful to industrial hygienists and other safety professionals when designing or auditing for personnel safety.

  15. Nuclear Computerized Library for Assessing Reactor Reliability (NUCLARR): Programmer's guide

    SciTech Connect (OSTI)

    Call, O. J.; Jacobson, J. A.

    1988-09-01

    The Nuclear Computerized Library for Assessing Reactor Reliability (NUCLARR) is an automated data base management system for processing and storing human error probability and hardware component failure data. The NUCLARR system software resides on an IBM (or compatible) personal micro-computer and can be used to furnish data inputs for both human and hardware reliability analysis in support of a variety of risk assessment activities. The NUCLARR system is documented in a five-volume series of reports. Volume 2 of this series is the Programmer's Guide for maintaining the NUCLARR system software. This Programmer's Guide provides, for the software engineer, an orientation to the software elements involved, discusses maintenance methods, and presents useful aids and examples. 4 refs., 75 figs., 1 tab.

  16. How to Estimate the Value of Service Reliability Improvements

    SciTech Connect (OSTI)

    Sullivan, Michael J.; Mercurio, Matthew G.; Schellenberg, Josh A.; Eto, Joseph H.

    2010-06-08

    A robust methodology for estimating the value of service reliability improvements is presented. Although econometric models for estimating value of service (interruption costs) have been established and widely accepted, analysts often resort to applying relatively crude interruption cost estimation techniques in assessing the economic impacts of transmission and distribution investments. This paper first shows how the use of these techniques can substantially impact the estimated value of service improvements. A simple yet robust methodology that does not rely heavily on simplifying assumptions is presented. When a smart grid investment is proposed, reliability improvement is one of the most frequently cited benefits. Using the best methodology for estimating the value of this benefit is imperative. By providing directions on how to implement this methodology, this paper sends a practical, usable message to the industry.

  17. Reliability analysis of electric power systems including time dependent sources†

    E-Print Network [OSTI]

    Kim, Younjong

    1987-01-01

    Chairman of Advisory Committee: Chanan Singh A method for reliability analysis of electric power systems with time dependent sources, such as photovoltaic and wind generation, is introduced. The fluctuating characteristic of unconventional generation... and active solar. wind, geothermal, and hydropower. Of all the renewable energy technologies that have been the focus of encouraging government and private R k D efforts, photovoltaic generation and wind turbine generation appear to be the leading...

  18. Final report : testing and evaluation for solar hot water reliability.

    SciTech Connect (OSTI)

    Caudell, Thomas P.; He, Hongbo; Menicucci, David F.; Mammoli, Andrea A.; Burch, Jay

    2011-07-01

    Solar hot water (SHW) systems are being installed by the thousands. Tax credits and utility rebate programs are spurring this burgeoning market. However, the reliability of these systems is virtually unknown. Recent work by Sandia National Laboratories (SNL) has shown that few data exist to quantify the mean time to failure of these systems. However, there is keen interest in developing new techniques to measure SHW reliability, particularly among utilities that use ratepayer money to pay the rebates. This document reports on an effort to develop and test new, simplified techniques to directly measure the state of health of fielded SHW systems. One approach was developed by the National Renewable Energy Laboratory (NREL) and is based on the idea that the performance of the solar storage tank can reliably indicate the operational status of the SHW systems. Another approach, developed by the University of New Mexico (UNM), uses adaptive resonance theory, a type of neural network, to detect and predict failures. This method uses the same sensors that are normally used to control the SHW system. The NREL method uses two additional temperature sensors on the solar tank. The theories, development, application, and testing of both methods are described in the report. Testing was performed on the SHW Reliability Testbed at UNM, a highly instrumented SHW system developed jointly by SNL and UNM. The two methods were tested against a number of simulated failures. The results show that both methods show promise for inclusion in conventional SHW controllers, giving them advanced capability in detecting and predicting component failures.

  19. A reliability assessment methodology for distribution systems with distributed generation†

    E-Print Network [OSTI]

    Duttagupta, Suchismita Sujaya

    2006-08-16

    is associated 11 Fig. 1. Sample Distribution Network with the network response to dynamic and transient failures caused from faults and other disturbances, which could result in widespread cascading outages and loss of stability [11]. This research will focus... and maintain reliable power systems because cost of interruptions and power outages can have severe economic impact on the utility and its customers. At present, the deregulated electric power utilities are being restructured and operated as distinct generation...

  20. SLAC modulator operation and reliability in the SLC Era

    SciTech Connect (OSTI)

    Donaldson, A.R.; Ashton, J.R.

    1992-06-01

    A discussion of the operation and reliability of the 244 modulators in the SLAC linac with an emphasis on the past three years of operation. The linac modulators were designed and built in the 60`s, upgraded for the SLAC Linear Collider (SLC) in the mid 80s, and despite their age are still reliable accelerator components. The 60s modulator operated at 65 MW peak and 83 kW average power. The upgrade resulted in 150 MW peak output at an average power of 87 kW, a modest increase since the repetition rate was dropped from 360 to 120 Hz. In the present accelerator configuration, the Linac operates as a source of electrons and positrons to a single pass coillider. The classic collider is a storage ring filled with oppositely charged, counter-rotating particles which are allowed to collide until an accelerator fault occurs and the stored beams are aborted. A reasonable storage ring can store and collide particles for as long as eight hours with a 10 or 20 minute filling time. A single pass collider, + on the other hand, can only produce e{sup {minus}} and e{sup +} collisions at whatever rate the source operates. To be effective the SLC must operate at 120 Hz with a very high degree of reliability and on a continuous basis. Fortunately, the linac has a modest excess of modulator/klystron systems which allows some measure of redundancy and hence some freedom from the constraint that all 244 modulator/klystrons operate simultaneously. Nonetheless, high importance is placed on modulator MTBF and MTRR or, in the parlance of reliability experts and accelerator physicists, availability. This is especially true of the modulators associated with the fundamental requirements of a collider such as injection, compression and positron production.

  1. SLAC modulator operation and reliability in the SLC Era

    SciTech Connect (OSTI)

    Donaldson, A.R.; Ashton, J.R.

    1992-06-01

    A discussion of the operation and reliability of the 244 modulators in the SLAC linac with an emphasis on the past three years of operation. The linac modulators were designed and built in the 60's, upgraded for the SLAC Linear Collider (SLC) in the mid 80s, and despite their age are still reliable accelerator components. The 60s modulator operated at 65 MW peak and 83 kW average power. The upgrade resulted in 150 MW peak output at an average power of 87 kW, a modest increase since the repetition rate was dropped from 360 to 120 Hz. In the present accelerator configuration, the Linac operates as a source of electrons and positrons to a single pass coillider. The classic collider is a storage ring filled with oppositely charged, counter-rotating particles which are allowed to collide until an accelerator fault occurs and the stored beams are aborted. A reasonable storage ring can store and collide particles for as long as eight hours with a 10 or 20 minute filling time. A single pass collider, + on the other hand, can only produce e{sup {minus}} and e{sup +} collisions at whatever rate the source operates. To be effective the SLC must operate at 120 Hz with a very high degree of reliability and on a continuous basis. Fortunately, the linac has a modest excess of modulator/klystron systems which allows some measure of redundancy and hence some freedom from the constraint that all 244 modulator/klystrons operate simultaneously. Nonetheless, high importance is placed on modulator MTBF and MTRR or, in the parlance of reliability experts and accelerator physicists, availability. This is especially true of the modulators associated with the fundamental requirements of a collider such as injection, compression and positron production.

  2. Gearbox Reliability Collaborative High-Speed Shaft Calibration

    SciTech Connect (OSTI)

    Keller, J.; McNiff, B.

    2014-09-01

    Instrumentation has been added to the high-speed shaft, pinion, and tapered roller bearing pair of the Gearbox Reliability Collaborative gearbox to measure loads and temperatures. The new shaft bending moment and torque instrumentation was calibrated and the purpose of this document is to describe this calibration process and results, such that the raw shaft bending and torque signals can be converted to the proper engineering units and coordinate system reference for comparison to design loads and simulation model predictions.

  3. ADVANCED COMPRESSOR ENGINE CONTROLS TO ENHANCE OPERATION, RELIABILITY AND INTEGRITY

    SciTech Connect (OSTI)

    Gary D. Bourn; Jess W. Gingrich; Jack A. Smith

    2004-03-01

    This document is the final report for the ''Advanced Compressor Engine Controls to Enhance Operation, Reliability, and Integrity'' project. SwRI conducted this project for DOE in conjunction with Cooper Compression, under DOE contract number DE-FC26-03NT41859. This report addresses an investigation of engine controls for integral compressor engines and the development of control strategies that implement closed-loop NOX emissions feedback.

  4. Gearbox Reliability Collaborative Phase 3 Gearbox 2 Test Plan

    SciTech Connect (OSTI)

    Link, H.; Keller, J.; Guo, Y.; McNiff, B.

    2013-04-01

    Gearboxes in wind turbines have not been achieving their expected design life even though they commonly meet or exceed the design criteria specified in current design standards. One of the basic premises of the National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC) is that the low gearbox reliability results from the absence of critical elements in the design process or insufficient design tools. Key goals of the GRC are to improve design approaches and analysis tools and to recommend practices and test methods resulting in improved design standards for wind turbine gearboxes that lower the cost of energy (COE) through improved reliability. The GRC uses a combined gearbox testing, modeling and analysis approach, along with a database of information from gearbox failures collected from overhauls and investigation of gearbox condition monitoring techniques to improve wind turbine operations and maintenance practices. Testing of Gearbox 2 (GB2) using the two-speed turbine controller that has been used in prior testing. This test series will investigate non-torque loads, high-speed shaft misalignment, and reproduction of field conditions in the dynamometer. This test series will also include vibration testing using an eddy-current brake on the gearbox's high speed shaft.

  5. Creating a Transactive Energy Framework: Improving Reliability and Efficiency

    SciTech Connect (OSTI)

    Melton, Ronald B.

    2013-11-01

    The use of demand response and other flexible distributed resources over the past decade for market efficiency and grid reliability has grown dramatically. Federal and state policy objectives point to an important role for customer loads, generation and storage in the management of an increasingly unpredictable power system. As we consider the need to substantially scale the use of flexible distributed energy resources, there has been growing attention to the need to address not only the economics, but also the control system implications to ensure grid reliability. This has led to a focus on an area of activity called ďTransactive Energy.Ē Transactive Energy refers to the combination of economic and control techniques that improve grid reliability and efficiency. These techniques may also be used to optimize operations within a customerís facility. The Department of Energy has supported the GridWiseģ Architecture Council (ďthe CouncilĒ) to develop a framework to provide opportunity for collaboration among the many stakeholders involved in the transformation of the power system.

  6. A Research Roadmap for Computation-Based Human Reliability Analysis

    SciTech Connect (OSTI)

    Boring, Ronald; Mandelli, Diego; Joe, Jeffrey; Smith, Curtis; Groth, Katrina

    2015-08-01

    The United States (U.S.) Department of Energy (DOE) is sponsoring research through the Light Water Reactor Sustainability (LWRS) program to extend the life of the currently operating fleet of commercial nuclear power plants. The Risk Informed Safety Margin Characterization (RISMC) research pathway within LWRS looks at ways to maintain and improve the safety margins of these plants. The RISMC pathway includes significant developments in the area of thermalhydraulics code modeling and the development of tools to facilitate dynamic probabilistic risk assessment (PRA). PRA is primarily concerned with the risk of hardware systems at the plant; yet, hardware reliability is often secondary in overall risk significance to human errors that can trigger or compound undesirable events at the plant. This report highlights ongoing efforts to develop a computation-based approach to human reliability analysis (HRA). This computation-based approach differs from existing static and dynamic HRA approaches in that it: (i) interfaces with a dynamic computation engine that includes a full scope plant model, and (ii) interfaces with a PRA software toolset. The computation-based HRA approach presented in this report is called the Human Unimodels for Nuclear Technology to Enhance Reliability (HUNTER) and incorporates in a hybrid fashion elements of existing HRA methods to interface with new computational tools developed under the RISMC pathway. The goal of this research effort is to model human performance more accurately than existing approaches, thereby minimizing modeling uncertainty found in current plant risk models.

  7. Estimation of structural reliability under combined loads. [PWR; BWR

    SciTech Connect (OSTI)

    Shinozuka, M.; Kako, T.; Hwang, H.; Brown, P.; Reich, M.

    1983-01-01

    For the overall safety evaluation of seismic category I structures subjected to various load combinations, a quantitative measure of the structural reliability in terms of a limit state probability can be conveniently used. For this purpose, the reliability analysis method for dynamic loads, which has recently been developed by the authors, was combined with the existing standard reliability analysis procedure for static and quasi-static loads. The significant parameters that enter into the analysis are: the rate at which each load (dead load, accidental internal pressure, earthquake, etc.) will occur, its duration and intensity. All these parameters are basically random variables for most of the loads to be considered. For dynamic loads, the overall intensity is usually characterized not only by their dynamic components but also by their static components. The structure considered in the present paper is a reinforced concrete containment structure subjected to various static and dynamic loads such as dead loads, accidental pressure, earthquake acceleration, etc. Computations are performed to evaluate the limit state probabilities under each load combination separately and also under all possible combinations of such loads.

  8. Managing electricity reliability risk through the futures markets

    SciTech Connect (OSTI)

    Siddiqui, Afzal S.

    2000-10-01

    In competitive electricity markets, the vertically integrated utilities that were responsible for ensuring system reliability in their own service territories, or groups of territories, often cease to exist. Typically, the burden falls to an independent system operator (ISO) to insure that enough ancillary services (AS) are available for safe, stable, and reliable operation of the grid, typically defined, in part, as compliance with officially approved engineering specifications for minimum levels of AS. In order to characterize the behavior of market participants (generators, retailers, and an ISO) in a competitive electricity market with reliability requirements, we model a spot market for electricity and futures markets for both electricity and AS. By assuming that each participant seeks to maximize its expected utility of wealth and that all markets clear, we solve for the optional quantities of electricity and AS traded in each market by all participants, as well as the corresponding market-clearing prices. We show that future prices for both electricity and AS depend on expectations of the spot price, statistical aspects of system demand, and production cost parameters. More important, our model captures the fact that electricity and AS are substitute products for the generators, implying that anticipated changes in the spot market will affect the equilibrium futures positions of both electricity and AS. We apply our model to the California electricity and AS markets to test its viability.

  9. Reliable High Performance Peta- and Exa-Scale Computing

    SciTech Connect (OSTI)

    Bronevetsky, G

    2012-04-02

    As supercomputers become larger and more powerful, they are growing increasingly complex. This is reflected both in the exponentially increasing numbers of components in HPC systems (LLNL is currently installing the 1.6 million core Sequoia system) as well as the wide variety of software and hardware components that a typical system includes. At this scale it becomes infeasible to make each component sufficiently reliable to prevent regular faults somewhere in the system or to account for all possible cross-component interactions. The resulting faults and instability cause HPC applications to crash, perform sub-optimally or even produce erroneous results. As supercomputers continue to approach Exascale performance and full system reliability becomes prohibitively expensive, we will require novel techniques to bridge the gap between the lower reliability provided by hardware systems and users unchanging need for consistent performance and reliable results. Previous research on HPC system reliability has developed various techniques for tolerating and detecting various types of faults. However, these techniques have seen very limited real applicability because of our poor understanding of how real systems are affected by complex faults such as soft fault-induced bit flips or performance degradations. Prior work on such techniques has had very limited practical utility because it has generally focused on analyzing the behavior of entire software/hardware systems both during normal operation and in the face of faults. Because such behaviors are extremely complex, such studies have only produced coarse behavioral models of limited sets of software/hardware system stacks. Since this provides little insight into the many different system stacks and applications used in practice, this work has had little real-world impact. My project addresses this problem by developing a modular methodology to analyze the behavior of applications and systems during both normal and faulty operation. By synthesizing models of individual components into a whole-system behavior models my work is making it possible to automatically understand the behavior of arbitrary real-world systems to enable them to tolerate a wide range of system faults. My project is following a multi-pronged research strategy. Section II discusses my work on modeling the behavior of existing applications and systems. Section II.A discusses resilience in the face of soft faults and Section II.B looks at techniques to tolerate performance faults. Finally Section III presents an alternative approach that studies how a system should be designed from the ground up to make resilience natural and easy.

  10. Smart Grid Update: Delivering More Reliable and Efficient Power...

    Broader source: Energy.gov (indexed) [DOE]

    Surge and Sea-Level Rise State and Regional Energy Risk Assessment Initiative National Electricity Delivery Division Infrastructure Security and Energy Restoration About Us...

  11. Nematode Communities in Organically and Conventionally Managed Agricultural Soils1

    E-Print Network [OSTI]

    Neher, Deborah A.

    Nematode Communities in Organically and Conventionally Managed Agricultural Soils1 Deborah A. Neher organically and conventionally managed soils in the Piedmont region of North Carolina. Available nitrogen availability. Soils were sampled six times yearly in 1993 and 1994 to determine the best time of year to sample

  12. Regional Carbon Sequestration Partnerships

    Broader source: Energy.gov [DOE]

    DOE has created a network of seven Regional Carbon Sequestration Partnerships (RCSPs) to help develop the technology, infrastructure, and regulations to implement large-scale CO2 storage (also...

  13. SOUTHWEST REGIONAL PARTNERSHIP ON CARBON SEQUESTRATION

    SciTech Connect (OSTI)

    Brian McPherson; Rick Allis; Barry Biediger; Joel Brown; Jim Cappa; George Guthrie; Richard Hughes; Eugene Kim; Robert Lee; Dennis Leppin; Charles Mankin; Orman Paananen; Rajesh Pawar; Tarla Peterson; Steve Rauzi; Jerry Stuth; Genevieve Young

    2004-11-01

    The Southwest Partnership Region includes six whole states, including Arizona, Colorado, Kansas, New Mexico, Oklahoma, and Utah, roughly one-third of Texas, and significant portions of adjacent states. The Partnership comprises a large, diverse group of expert organizations and individuals specializing in carbon sequestration science and engineering, as well as public policy and outreach. The main objective of the Southwest Partnership project is to achieve an 18% reduction in carbon intensity by 2012. The Partnership made great progress in this first year. Action plans for possible Phase II carbon sequestration pilot tests in the region are almost finished, including both technical and non-technical aspects necessary for developing and carrying out these pilot tests. All partners in the Partnership are taking an active role in evaluating and ranking optimum sites and technologies for capture and storage of CO{sub 2} in the Southwest Region. We are identifying potential gaps in all aspects of potential sequestration deployment issues.

  14. Regionalism in international air transportation--cooperation and competition : papers from an international conference organized by the Massachusetts Institute of Technology, held at the Amman Chamber of Commerce, Amman, Jordan, April 19-21, 1983, under the auspices of Alia, the Royal Jordanian Airline.

    E-Print Network [OSTI]

    Massachusetts Institute of Technology.; \\02BBAlyah.; Massachusetts Institute of Technology. Flight Transportation Laboratory

    Preface: Alia: The Royal Jordanian Airline is very pleased to present this collectiont of papers originally presented at the international conference entitled, "Regionalism in International Air Transportation: Cooperation ...

  15. Regional Energy Deployment System (ReEDS)

    SciTech Connect (OSTI)

    Short, W.; Sullivan, P.; Mai, T.; Mowers, M.; Uriarte, C.; Blair, N.; Heimiller, D.; Martinez, A.

    2011-12-01

    The Regional Energy Deployment System (ReEDS) is a deterministic optimization model of the deployment of electric power generation technologies and transmission infrastructure throughout the contiguous United States into the future. The model, developed by the National Renewable Energy Laboratory's Strategic Energy Analysis Center, is designed to analyze the critical energy issues in the electric sector, especially with respect to potential energy policies, such as clean energy and renewable energy standards or carbon restrictions. ReEDS provides a detailed treatment of electricity-generating and electrical storage technologies and specifically addresses a variety of issues related to renewable energy technologies, including accessibility and cost of transmission, regional quality of renewable resources, seasonal and diurnal generation profiles, variability of wind and solar power, and the influence of variability on the reliability of the electrical grid. ReEDS addresses these issues through a highly discretized regional structure, explicit statistical treatment of the variability in wind and solar output over time, and consideration of ancillary services' requirements and costs.

  16. Glassy dynamics distinguishes chromosome organization across organisms

    E-Print Network [OSTI]

    Hongsuk Kang; Young-Gui Yoon; D. Thirumalai; Changbong Hyeon

    2015-06-03

    Recent experiments showing scaling of the intrachromosomal contact probability, $P(s)\\sim s^{-1}$ with the genomic distance $s$, are interpreted to mean a self-similar fractal-like chromosome organization. However, scaling of $P(s)$ varies across organisms, requiring an explanation. We illustrate that dynamical arrest in a highly confined space as a discriminating marker for genome organization, by modeling chromosome inside a nucleus as a self-avoiding homopolymer confined to a sphere of varying sizes. Brownian dynamics simulations show that the chain dynamics slows down as the polymer volume fraction ($\\phi$) inside the confinement approaches a critical value $\\phi_c$. Using finite size scaling analysis, we determine $\\phi_c^{\\infty}\\approx 0.44$ for a sufficiently long polymer ($N\\gg 1$). Our study shows that the onset of glassy dynamics is the reason for the formation of segregated organization in human chromosomes ($N\\approx 3\\times 10^9$, $\\phi\\gtrsim\\phi_c^{\\infty}$), whereas chromosomes of budding yeast ($N\\approx 1.2\\times 10^7$, $\\phi<\\phi_c^{\\infty}$) are equilibrated with no clear signature of such organization.

  17. A long Saharan dust event over the western Mediterranean: Lidar, Sun photometer observations, and regional dust modeling

    E-Print Network [OSTI]

    over the Mediterranean region (http://www.bsc.es/projects/earthscience/ DREAM/) considering four of dust exported annually from northern Africa (Sahara-Sahel region) are still not reliable, and range]. Once in the atmosphere, dust particles interact with solar and thermal radiation, modulating the Earth

  18. Particle contamination control in plasma processing: Building-in reliability for semiconductor fabrication

    SciTech Connect (OSTI)

    Selwyn, G.S.

    1995-12-31

    Plasma processing is used for {approximately}35% of the process steps required for semiconductor manufacturing. Recent studies have shown that plasma processes create the greatest amount of contaminant dust of all the manufacturing steps required for device fabrication. Often, the level of dust in a plasma process tool exceeds the cleanroom by several orders of magnitude. Particulate contamination generated in a plasma tool can result in reliability problems as well as device failure. Inter-level wiring shorts different levels of metallization on a device is a common result of plasma particulate contamination. We have conducted a thorough study of the physics and chemistry involved in particulate formation and transport in plasma tools. In-situ laser light scattering (LLS) is used for real-time detection of the contaminant dust. The results of this work are highly surprising: all plasmas create dust; the dust can be formed by homogeneous as well as heterogeneous chemistry; this dust is charged and suspended in the plasma; additionally, it is transported to favored regions of the plasma, such as those regions immediately above wafers. Fortunately, this work has also led to a novel means of controlling and eliminating these unwanted contaminants: electrostatic {open_quotes}drainpipes{close_quotes} engineered into the electrode by means of specially designed grooves. These channel the suspended particles out of the plasma and into the pump port before they can fall onto the wafer.

  19. On the reliability of microvariability tests in quasars

    SciTech Connect (OSTI)

    De Diego, Josť A.

    2014-11-01

    Microvariations probe the physics and internal structure of quasars. Unpredictability and small flux variations make this phenomenon elusive and difficult to detect. Variance-based probes such as the C and F tests, or a combination of both, are popular methods to compare the light curves of the quasar and a comparison star. Recently, detection claims in some studies have depended on the agreement of the results of the C and F tests, or of two instances of the F-test, for rejecting the non-variation null hypothesis. However, the C-test is a non-reliable statistical procedure, the F-test is not robust, and the combination of tests with concurrent results is anything but a straightforward methodology. A priori power analysis calculations and post hoc analysis of Monte Carlo simulations show excellent agreement for the analysis of variance test to detect microvariations as well as the limitations of the F-test. Additionally, the combined tests yield correlated probabilities that make the assessment of statistical significance unworkable. However, it is possible to include data from several field stars to enhance the power in a single F-test, increasing the reliability of the statistical analysis. This would be the preferred methodology when several comparison stars are available. An example using two stars and the enhanced F-test is presented. These results show the importance of using adequate methodologies and avoiding inappropriate procedures that can jeopardize microvariability detections. Power analysis and Monte Carlo simulations are useful tools for research planning, as they can demonstrate the robustness and reliability of different research approaches.

  20. Fifty Years of THERP and Human Reliability Analysis

    SciTech Connect (OSTI)

    Ronald L. Boring

    2012-06-01

    In 1962 at a Human Factors Society symposium, Alan Swain presented a paper introducing a Technique for Human Error Rate Prediction (THERP). This was followed in 1963 by a Sandia Laboratories monograph outlining basic human error quantification using THERP and, in 1964, by a special journal edition of Human Factors on quantification of human performance. Throughout the 1960s, Swain and his colleagues focused on collecting human performance data for the Sandia Human Error Rate Bank (SHERB), primarily in connection with supporting the reliability of nuclear weapons assembly in the US. In 1969, Swain met with Jens Rasmussen of RisÝ National Laboratory and discussed the applicability of THERP to nuclear power applications. By 1975, in WASH-1400, Swain had articulated the use of THERP for nuclear power applications, and the approach was finalized in the watershed publication of the NUREG/CR-1278 in 1983. THERP is now 50 years old, and remains the most well known and most widely used HRA method. In this paper, the author discusses the history of THERP, based on published reports and personal communication and interviews with Swain. The author also outlines the significance of THERP. The foundations of human reliability analysis are found in THERP: human failure events, task analysis, performance shaping factors, human error probabilities, dependence, event trees, recovery, and pre- and post-initiating events were all introduced in THERP. While THERP is not without its detractors, and it is showing signs of its age in the face of newer technological applications, the longevity of THERP is a testament of its tremendous significance. THERP started the field of human reliability analysis. This paper concludes with a discussion of THERP in the context of newer methods, which can be seen as extensions of or departures from Swainís pioneering work.

  1. Failure and Reliability Analysis for the Master Pump Shutdown System

    SciTech Connect (OSTI)

    BEVINS, R.R.

    2000-09-05

    The Master Pump Shutdown System (MPSS) will be installed in the 200 Areas of the Hanford Site to monitor and control the transfer of liquid waste between tank farms and between the 200 West and 200 East areas through the Cross-Site Transfer Line. The Safety Function provided by the MPSS is to shutdown any waste transfer process within or between tank farms if a waste leak should occur along the selected transfer route. The MPSS, which provides this Safety Class Function, is composed of Programmable Logic Controllers (PLCs), interconnecting wires, relays, Human to Machine Interfaces (HMI), and software. These components are defined as providing a Safety Class Function and will be designated in this report as MPSS/PLC. Input signals to the MPSS/PLC are provided by leak detection systems from each of the tank farm leak detector locations along the waste transfer route. The combination of the MPSS/PLC, leak detection system, and transfer pump controller system will be referred to as MPSS/SYS. The components addressed in this analysis are associated with the MPSS/SYS. The purpose of this failure and reliability analysis is to address the following design issues of the Project Development Specification (PDS) for the MPSS/SYS (HNF 2000a): (1) Single Component Failure Criterion, (2) System Status Upon Loss of Electrical Power, (3) Physical Separation of Safety Class cables, (4) Physical Isolation of Safety Class Wiring from General Service Wiring, and (5) Meeting the MPSS/PLC Option 1b (RPP 1999) Reliability estimate. The failure and reliability analysis examined the system on a component level basis and identified any hardware or software elements that could fail and/or prevent the system from performing its intended safety function.

  2. EA-1801: Granite Reliable Power Wind Park Project in Coos County...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    01: Granite Reliable Power Wind Park Project in Coos County, NH EA-1801: Granite Reliable Power Wind Park Project in Coos County, NH June 25, 2010 EA-1801: Final Environmental...

  3. Reliability Assessment of Fault-Tolerant Dc-Dc Converters for Photovoltaic Applications

    E-Print Network [OSTI]

    Liberzon, Daniel

    Reliability Assessment of Fault-Tolerant Dc-Dc Converters for Photovoltaic Applications Sairaj V in photovoltaic energy processing applications is presented. The proposed approach acknowledges the influence through several case studies. Index Terms-- Markov reliability modeling, photovoltaic systems, power

  4. A Survey of NASA and Military Standards on Fault Tolerance and Reliability Applied to Robotics

    E-Print Network [OSTI]

    Rice University - Center for Cooperative Autonomous Robots for Hazardous Environments

    A Survey of NASA and Military Standards on Fault Tolerance and Reliability Applied to Robotics of relevant Military and NASA standards for reliability and fault toler≠ ance is included. 1 Introduction

  5. When Sugar Turns to Sh%&: Immediate Action Decision Making and Resilience in High Reliability Teams†

    E-Print Network [OSTI]

    Wesner, Bradley Scott

    2012-02-14

    more nuanced study of high reliability processes within team contexts is warranted. This study focuses on organizational teams which are faced with the challenges of maintaining high levels of reliability. Of particular interest is how teams manage...

  6. Transmission System Expansion Plans in View Point of Deterministic, Probabilistic and Security Reliability Criteria

    E-Print Network [OSTI]

    Transmission System Expansion Plans in View Point of Deterministic, Probabilistic and Security reliability criterion, probabilistic reliability criterion and security criterion based on N- contingency control system as well as reasonable strength of grid originally. Because investment for power system

  7. Reliability-based calibration of design seismic response spectra and structural acceptance criteria

    E-Print Network [OSTI]

    Baker, Jack W.

    Reliability-based calibration of design seismic response spectra and structural acceptance criteria: Earthquake engineering design requires an evaluation of the structure's reliability over future seismic loads alternate "explicit" check, which commonly specifies a design spectrum and associated structural response

  8. Quasi-optical network analyzers and high-reliability RF MEMS switched capacitors

    E-Print Network [OSTI]

    Grichener, Alexander

    2011-01-01

    Chapter 3 High-Reliability RF MEMS Switched Capacitors 3.1Technology 1.2 RF MEMS Technology . . . . . . . . . . . . .Reliability High-Q Switched RF MEMS CapacitorsĒ IEEE Int.

  9. System Reliability: A Case When Fuzzy Logic Enhances Probability Theory's Ability

    E-Print Network [OSTI]

    Kreinovich, Vladik

    . Zadeh explains that probabil≠ ity theory needs an infusion of fuzzy logic to enhance its ability to deal such an infusion is indeed successful: the problem of system reliability. 1. Reliability: Brief Introduction

  10. New York Completes Smart Grid Project to Build a More Reliable...

    Energy Savers [EERE]

    New York Completes Smart Grid Project to Build a More Reliable, Resilient Power Grid New York Completes Smart Grid Project to Build a More Reliable, Resilient Power Grid April 15,...

  11. The Impact of Protection System Failures on Power System Reliability Evaluation†

    E-Print Network [OSTI]

    Jiang, Kai

    2012-11-05

    The reliability of protection systems has emerged as an important topic because protection failures have critical influence on the reliability of power systems. The goal of this research is to develop novel approaches for ...

  12. Southeast Texas Region Regional Public Transportation Coordination Plan†

    E-Print Network [OSTI]

    Southeast Texas Regional Planning Commission

    2006-01-01

    REGION REGIONAL PUBLIC TRANSPORTATION COORDINATION PLAN PREPARED FOR THE TEXAS DEPARTMENT OF TRANSPORTATION NOVEMBER 2006 REGIONAL PUBLIC TRANSPORTATION COORDINATION PLAN NOVEMBER 2006 PAGE 1 Table of Contents... ....................................................................4 History of Regional Coordination of Public Transportation ..............................10 REGIONAL SERVICE COORDINATION PLANNING........................................................10 Lead Agency...

  13. 2012 Reliability & Markets Peer Review | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on DeliciousMathematics AndBeryllium Diseasem-2m-3l-04-05-2012.xlsxFront CoverDepartment ofLoad as2012 ProgramReliability

  14. Robot-Powered Reliability Testing at NREL's ESIF

    SciTech Connect (OSTI)

    Harrison, Kevin

    2013-12-05

    With auto manufacturers expected to roll out fuel cell electric vehicles in the 2015 to 2017 timeframe, the need for a reliable hydrogen fueling infrastructure is greater than ever. That's why the National Renewable Energy Laboratory (NREL) is using a robot in its Energy Systems Integration Facility (ESIF) to assess the durability of hydrogen fueling hoses, a largely untestedóand currently costlyócomponent of hydrogen fueling stations. The automated machine mimics the repetitive stress of a human bending and twisting the hose to refuel a vehicleóall under the high pressure and low temperature required to deliver hydrogen to a fuel cell vehicle's onboard storage tank.

  15. Improving reliability in the SLC (Stanford Linear Collider) control system

    SciTech Connect (OSTI)

    Heinen, N.; Spencer, N.; Tinsman, J.

    1989-10-01

    During the past year, considerable emphasis has been placed on improving the overall reliability of the SLC control system. The Errorlog Facility has proven a useful tool to diagnose hardware and software problems. By analyzing the various error messages and their correlations, one can usually determine the software component or hardware module causing faults. Daily summaries help to identify problems so that they can be remedied before they become catastrophic; thereby bringing about a considerable increase in performance. We discuss the various tools we use and our operational experience with them. 3 refs., 6 figs.

  16. Blade reliability collaborative : collection of defect, damage and repair data.

    SciTech Connect (OSTI)

    Ashwill, Thomas D.; Ogilvie, Alistair B.; Paquette, Joshua A.

    2013-04-01

    The Blade Reliability Collaborative (BRC) was started by the Wind Energy Technologies Department of Sandia National Laboratories and DOE in 2010 with the goal of gaining insight into planned and unplanned O&M issues associated with wind turbine blades. A significant part of BRC is the Blade Defect, Damage and Repair Survey task, which will gather data from blade manufacturers, service companies, operators and prior studies to determine details about the largest sources of blade unreliability. This report summarizes the initial findings from this work.

  17. Computing fractal dimension in supertransient systems directly, fast and reliable

    E-Print Network [OSTI]

    Romulus Breban; Helena E. Nusse

    2006-08-07

    Chaotic transients occur in many experiments including those in fluids, in simulations of the plane Couette flow, and in coupled map lattices and they are a common phenomena in dynamical systems. Superlong chaotic transients are caused by the presence of chaotic saddles whose stable sets have fractal dimensions that are close to phase-space dimension. For many physical systems chaotic saddles have a big impact on laboratory measurements, and it is important to compute the dimension of such stable sets including fractal basin boundaries through a direct method. In this work, we present a new method to compute the dimension of stable sets of chaotic saddles directly, fast, and reliable.

  18. Reliability Improvement Programs in Steam Distribution and Power Generation Systems†

    E-Print Network [OSTI]

    Atlas, R. D.

    1986-01-01

    , and the paybacks associated with instituting a program of planned and systematic maintenance manage ment of that system. Energy costs can be reduced by 10% and maintenance costs by 20%, while achieving other tan gible improvements in the reliability...-up; and 6)'software and data base management. Several case studies, in which the concept has been success fully applied, will be presented. INTRODUCTION Energy costs have been on the rise for the last 10 years and have now leveled off due to global...

  19. Robot-Powered Reliability Testing at NREL's ESIF

    ScienceCinema (OSTI)

    Harrison; Kevin

    2014-06-10

    With auto manufacturers expected to roll out fuel cell electric vehicles in the 2015 to 2017 timeframe, the need for a reliable hydrogen fueling infrastructure is greater than ever. That's why the National Renewable Energy Laboratory (NREL) is using a robot in its Energy Systems Integration Facility (ESIF) to assess the durability of hydrogen fueling hoses, a largely untested-and currently costly-component of hydrogen fueling stations. The automated machine mimics the repetitive stress of a human bending and twisting the hose to refuel a vehicle-all under the high pressure and low temperature required to deliver hydrogen to a fuel cell vehicle's onboard storage tank.

  20. Robot-Powered Reliability Testing at NREL's ESIF

    SciTech Connect (OSTI)

    Harrison; Kevin

    2013-12-05

    With auto manufacturers expected to roll out fuel cell electric vehicles in the 2015 to 2017 timeframe, the need for a reliable hydrogen fueling infrastructure is greater than ever. That's why the National Renewable Energy Laboratory (NREL) is using a robot in its Energy Systems Integration Facility (ESIF) to assess the durability of hydrogen fueling hoses, a largely untested-and currently costly-component of hydrogen fueling stations. The automated machine mimics the repetitive stress of a human bending and twisting the hose to refuel a vehicle-all under the high pressure and low temperature required to deliver hydrogen to a fuel cell vehicle's onboard storage tank.

  1. Reliable Gas Turbine Output: Attaining Temperature Independent Performance†

    E-Print Network [OSTI]

    Neeley, J. E.; Patton, S.; Holder, F.

    1992-01-01

    stream_source_info ESL-IE-92-04-10.pdf.txt stream_content_type text/plain stream_size 16831 Content-Encoding ISO-8859-1 stream_name ESL-IE-92-04-10.pdf.txt Content-Type text/plain; charset=ISO-8859-1 RELIABLE GAS TURBINE... OUTPUT; ATTAINING TEMPERATURE INDEPENDENT PERFORMANCE James E. Neeley, P.E. Power Plant Engineer Public Utility Commission of Texas Austin, Texas ABSTRACT Improvements in gas turbine efficiency, coupled with dropping gas prices, has made gas...

  2. Reliability Testing the Die-Attach of CPV Cell Assemblies

    SciTech Connect (OSTI)

    Bosco, N.; Sweet, C.; Kurtz, S.

    2011-02-01

    Results and progress are reported for a course of work to establish an efficient reliability test for the die-attach of CPV cell assemblies. Test vehicle design consists of a ~1 cm2 multijunction cell attached to a substrate via several processes. A thermal cycling sequence is developed in a test-to-failure protocol. Methods of detecting a failed or failing joint are prerequisite for this work; therefore both in-situ and non-destructive methods, including infrared imaging techniques, are being explored as a method to quickly detect non-ideal or failing bonds.

  3. NREL: Gearbox Reliability Collaborative - Working with the Gearbox

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass map shines light on771/6/14RecentGeospatialReliability Collaborative Research Wind

  4. Sandia Energy - Reliability, O&M, Standards Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II)Geothermal Energy &WaterNewPhotoionizationPowerRadarReliability,

  5. ,"Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1. Net1. Net

  6. ,"Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1. Net1.

  7. ,"Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1.

  8. ,"Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1.. Net

  9. ,"Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1.. Net3 and

  10. ,"Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1.. Net3

  11. ,"Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1.. Net32005

  12. ,"Table 2a. Noncoincident Summer Peak Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1..a.

  13. ,"Table 2a. Noncoincident Summer Peak Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by EndAnnual",2014Annual",2014Totale.1..a.a.

  14. ,"Table 2a. Noncoincident Summer Peak Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by

  15. ,"Table 2a. Noncoincident Summer Peak Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010" ,"Next

  16. ,"Table 2a. Noncoincident Summer Peak Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010" ,"Next3

  17. ,"Table 2a. Noncoincident Summer Peak Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"

  18. ,"Table 2a. Noncoincident Summer Peak Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"2005 and

  19. ,"Table 2b. Noncoincident Winter Peak Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"2005 andb.

  20. ,"Table 2b. Noncoincident Winter Peak Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"2005 andb.b.

  1. ,"Table 2b. Noncoincident Winter Peak Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"2005

  2. ,"Table 2b. Noncoincident Winter Peak Load, Actual and Projected by North American Electric Reliability Corporation Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"20052b.

  3. ,"Table 2b. Noncoincident Winter Peak Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"20052b.3 and

  4. ,"Table 2b. Noncoincident Winter Peak Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"20052b.3 and4

  5. ,"Table 2b. Noncoincident Winter Peak Load, Actual and Projected by North American Electric Reliability Council Region, "

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames City of",6,1,"Omaha Public PowerOECD/IEA - 2008Wellhead PriceConsumption by9" ,"Released: December 2010"20052b.3

  6. Next Update: December 2011 Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Corporation Region,

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames5 Tables July 1996 Energy Information Administration Office of Coal, Nuclear,DecadeYear Jan Feb Mar Apr MayDecade Year-0Decade Year-00 0 03ae.

  7. Next Update: October 2009 Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Corporation Region,

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames5 Tables July 1996 Energy Information Administration Office of Coal, Nuclear,DecadeYear Jan Feb Mar Apr MayDecade Year-0Decade Year-00 07a .b1.

  8. Next Update: October 2010 Table 1. Net Energy For Load, Actual and Projected by North American Electric Reliability Corporation Region,

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home PageMonthly","10/2015"4,"Ames5 Tables July 1996 Energy Information Administration Office of Coal, Nuclear,DecadeYear Jan Feb Mar Apr MayDecade Year-0Decade Year-00

  9. Nonlinear organic plasmonics

    E-Print Network [OSTI]

    Fainberg, B D

    2015-01-01

    Purely organic materials with negative and near-zero dielectric permittivity can be easily fabricated. Here we develop a theory of nonlinear non-steady-state organic plasmonics with strong laser pulses. The bistability response of the electron-vibrational model of organic materials in the condensed phase has been demonstrated. Non-steady-state organic plasmonics enable us to obtain near-zero dielectric permittivity during a short time. We have proposed to use non-steady-state organic plasmonics for the enhancement of intersite dipolar energy-transfer interaction in the quantum dot wire that influences on electron transport through nanojunctions. Such interactions can compensate Coulomb repulsions for particular conditions. We propose the exciton control of Coulomb blocking in the quantum dot wire based on the non-steady-state near-zero dielectric permittivity of the organic host medium.

  10. Performance and Reliability of Bonded Interfaces for High-Temperature Packaging (Presentation)

    SciTech Connect (OSTI)

    Devoto, D.

    2014-06-01

    This presentation reviews the status of the performance and reliability of bonded interfaces for high-temperature packaging.

  11. Software Selection for Reliability Optimization using Time Series Analysis and Machine Learning

    E-Print Network [OSTI]

    Mu, Yali

    2013-01-01

    of Software Selection . . . . . . . . . . . . . . . . . . .for the software reliability. . . . . . . . . . . . . . K-number of bugs for software. Accumulated number of bugs

  12. Northeast Regional Biomass Program

    SciTech Connect (OSTI)

    Lusk, P.D.

    1992-12-01

    The Northeast Regional Biomass Program has been in operation for a period of nine years. During this time, state managed programs and technical programs have been conducted covering a wide range of activities primarily aim at the use and applications of wood as a fuel. These activities include: assessments of available biomass resources; surveys to determine what industries, businesses, institutions, and utility companies use wood and wood waste for fuel; and workshops, seminars, and demonstrations to provide technical assistance. In the Northeast, an estimated 6.2 million tons of wood are used in the commercial and industrial sector, where 12.5 million cords are used for residential heating annually. Of this useage, 1504.7 mw of power has been generated from biomass. The use of wood energy products has had substantial employment and income benefits in the region. Although wood and woodwaste have received primary emphasis in the regional program, the use of municipal solid waste has received increased emphasis as an energy source. The energy contribution of biomass will increase as potentia users become more familiar with existing feedstocks, technologies, and applications. The Northeast Regional Biomass Program is designed to support region-specific to overcome near-term barriers to biomass energy use.

  13. Mid-Atlantic Regional Wind Energy Institute

    SciTech Connect (OSTI)

    Courtney Lane

    2011-12-20

    As the Department of Energy stated in its 20% Wind Energy by 2030 report, there will need to be enhanced outreach efforts on a national, state, regional, and local level to communicate wind development opportunities, benefits and challenges to a diverse set of stakeholders. To help address this need, PennFuture was awarded funding to create the Mid-Atlantic Regional Wind Energy Institute to provide general education and outreach on wind energy development across Maryland, Virginia, Delaware, Pennsylvania and West Virginia. Over the course of the two-year grant period, PennFuture used its expertise on wind energy policy and development in Pennsylvania and expanded it to other states in the Mid-Atlantic region. PennFuture accomplished this through reaching out and establishing connections with policy makers, local environmental groups, health and economic development organizations, and educational institutions and wind energy developers throughout the Mid-Atlantic region. PennFuture conducted two regional wind educational forums that brought together wind industry representatives and public interest organizations from across the region to discuss and address wind development in the Mid-Atlantic region. PennFuture developed the agenda and speakers in collaboration with experts on the ground in each state to help determine the critical issue to wind energy in each location. The sessions focused on topics ranging from the basics of wind development; model ordinance and tax issues; anti-wind arguments and counter points; wildlife issues and coalition building. In addition to in-person events, PennFuture held three webinars on (1) Generating Jobs with Wind Energy; (2) Reviving American Manufacturing with Wind Power; and (3) Wind and Transmission. PennFuture also created a web page for the institute (http://www.midatlanticwind.org) that contains an online database of fact sheets, research reports, sample advocacy letters, top anti-wind claims and information on how to address them, wind and wildlife materials and sample model ordinances. Video and presentations from each in-person meeting and webinar recordings are also available on the site. At the end of the two-year period, PennFuture has accomplished its goal of giving a unified voice and presence to wind energy advocates in the Mid-Atlantic region. We educated a broad range of stakeholders on the benefits of wind energy and gave them the tools to help make a difference in their states. We grew a database of over 500 contacts and hope to continue the discussion and work around the importance of wind energy in the region.

  14. Introduction to Model-based Reliability Evaluation of Wireless Sensor Networks

    E-Print Network [OSTI]

    Breu, Ruth

    Introduction to Model-based Reliability Evaluation of Wireless Sensor Networks C. J®aggle J: A high level of reliability is a significant requirement for using wireless sensor networks in industrial environments. Model-based evaluation is usually applied in conventional systems to estimate the reliability

  15. A Reliable and Secure Cloud Storage Schema Using Multiple Service Providers

    E-Print Network [OSTI]

    Xu, Haiping

    A Reliable and Secure Cloud Storage Schema Using Multiple Service Providers Haiping Xu and Deepti stored in the cloud. In this paper, we propose a reliable and secure cloud storage schema using multiple at the server side, we propose a reliable and secure cloud storage schema that can be implemented at the client

  16. IEEE TRANSACTIONS ON RELIABILITY, VOL. 63, NO. 3, SEPTEMBER 2014 1 In Memoriam

    E-Print Network [OSTI]

    Li, Haijun

    IEEE TRANSACTIONS ON RELIABILITY, VOL. 63, NO. 3, SEPTEMBER 2014 1 In Memoriam Susan Hong Xu (1952≠2014) (Associate Editor of IEEE Transactions on Reliability) SUSAN Hong Xu (1952≠2014) was for twenty-seven years, Professor Xu has provided outstanding service as an Associate Editor of IEEE TRANSACTIONS ON RELIABILITY

  17. Using Empirical Data to Find the Best Measurement for Travel Time Reliability

    E-Print Network [OSTI]

    Alemazkoor, Negin

    2014-08-20

    . In this research, data from Katy Freeway, where travelers choose between tolled but reliable lanes and free but less reliable lanes, was used in an attempt to find the best measurement of reliability that could lead to the best explanation of travelersí lane choice...

  18. Measuring Reliability of Software Products Pankaj Jalote, Brendan Murphy, Mario Garzia, Ben Errez

    E-Print Network [OSTI]

    Jalote, Pankaj

    1 Measuring Reliability of Software Products Pankaj Jalote, Brendan Murphy, Mario Garzia, Ben Errez products. In these approaches, the product reliability is traditionally measured in terms of catastrophic, and then discuss two systems being used for measuring reliability of commercial software products. 1. Introduction

  19. Performance and Reliability of Interface Materials for Automotive Power Electronics (Presentation)

    SciTech Connect (OSTI)

    Narumanchi, S.; DeVoto, D.; Mihalic, M.; Paret, P.

    2013-07-01

    Thermal management and reliability are important because excessive temperature can degrade the performance, life, and reliability of power electronics and electric motors. Advanced thermal management technologies enable keeping temperature within limits; higher power densities; and lower cost materials, configurations and systems. Thermal interface materials, bonded interface materials and the reliability of bonded interfaces are discussed in this presentation.

  20. Organization and Functions

    Office of Environmental Management (EM)

    Organization and Functions Mission Unit EM-30 Deputy Assistant SecretaryADAS Waste Management Director Office of Packaging and Transportation EM-33 Regulations & Standards...

  1. Astatinated organic compounds

    DOE Patents [OSTI]

    Milius, R.A.; Lambrecht, R.M.; Bloomer, W.D.

    1989-05-02

    Methods and kits for incorporating a radioactive astatine isotope (particularly [sup 211]At) into an organic compound by electrophilic astatodestannylation of organostannanes. 3 figs.

  2. Organic vapor jet printing system

    DOE Patents [OSTI]

    Forrest, Stephen R

    2012-10-23

    An organic vapor jet printing system includes a pump for increasing the pressure of an organic flux.

  3. Northeast Regional Biomass Program

    SciTech Connect (OSTI)

    O'Connell, R.A.

    1991-11-01

    The management structure and program objectives for the Northeast Regional Biomass Program (NRBP) remain unchanged from previous years. Additional funding was provided by the Bonneville Power Administration Regional Biomass Program to continue the publication of articles in the Biologue. The Western Area Power Administration and the Council of Great Lakes Governors funded the project Characterization of Emissions from Burning Woodwaste''. A grant for the ninth year was received from DOE. The Northeast Regional Biomass Steering Committee selected the following four projects for funding for the next fiscal year. (1) Wood Waste Utilization Conference, (2) Performance Evaluation of Wood Systems in Commercial Facilities, (3) Wood Energy Market Utilization Training, (4) Update of the Facility Directory.

  4. NV PFA Regional Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    James Faulds

    2015-10-28

    This project focused on defining geothermal play fairways and development of a detailed geothermal potential map of a large transect across the Great Basin region (96,000 km2), with the primary objective of facilitating discovery of commercial-grade, blind geothermal fields (i.e. systems with no surface hot springs or fumaroles) and thereby accelerating geothermal development in this promising region. Data included in this submission consists of: structural settings (target areas, recency of faulting, slip and dilation potential, slip rates, quality), regional-scale strain rates, earthquake density and magnitude, gravity data, temperature at 3 km depth, permeability models, favorability models, degree of exploration and exploration opportunities, data from springs and wells, transmission lines and wilderness areas, and published maps and theses for the Nevada Play Fairway area.

  5. Reliability comparison of various nuclear propulsion configurations for Mars mission

    SciTech Connect (OSTI)

    Segna, D.R. [USDOE Richland Operations Office, WA (United States); Dagle, J.E. [Pacific Northwest Lab., Richland, WA (United States); Lyon, W.F. III [Westinghouse Hanford Co., Richland, WA (United States)

    1992-01-01

    Currently, trade-offs are being made among the various propulsion systems being considered for the Space Exploration Initiative (SEI) missions. It is necessary to investigate the reliability aspects as well as the efficiency, mass savings, and experience characteristics of the various configurations. Reliability is a very important factor for the SEI missions because of the long duration and because problems will be fixed onboard. The propulsion options that were reviewed consist of nuclear thermal propulsion (NTP), nuclear electric propulsion (NEP) and various configurations of each system. There were four configurations developed for comparison with the NTP as baselined in the Synthesis (1991): (1) NEP, (2) hybrid NEP/NTP, (3) hybrid with power beaming, and (4) NTP upper stage on the heavy lift launch vehicle (HLLV). The comparisons were based more or less on a qualitative review of complexity, stress levels and operations for each of the four configurations. Each configuration included a pressurized NEP and an NTP ascent stage propulsion system for the Mars mission.

  6. Integrated design environment for human performance and human reliability analysis

    SciTech Connect (OSTI)

    Nelson, W.R.

    1997-05-01

    Work over the last few years at the Idaho National Engineering and Environmental Laboratory (INEEL) has included a major focus on applying human performance and human reliability knowledge and methods as an integral element of system design and development. This work has been pursued in programs in a wide variety of technical domains, beginning with nuclear power plant operations. Since the mid-1980`s the laboratory has transferred the methods and tools developed in the nuclear domain to military weapons systems and aircraft, offshore oil and shipping operations, and commercial aviation operations and aircraft design. Through these diverse applications the laboratory has developed an integrated approach and framework for application of human performance analysis, human reliability analysis (HRA), operational data analysis, and simulation studies of human performance to the design and development of complex systems. This approach was recently tested in the NASA Advanced Concepts Program {open_quotes}Structured Human Error Analysis for Aircraft Design.{close_quotes} This program resulted in the prototype software tool THEA (Tool for Human Error Analysis) for incorporating human error analysis in the design of commercial aircraft, focusing on airplane maintenance tasks. Current effort is directed toward applying this framework to the development of advanced Air Traffic Management (ATM) systems as part of NASA`s Advanced Air Transportation Technologies (AATT) program. This paper summarizes the approach, describes recent and current applications in commercial aviation, and provides perspectives on how the approach could be utilized in the nuclear power industry.

  7. Regional Energy Baseline†

    E-Print Network [OSTI]

    Kim, H.; Baltazar, J.C.; Haberl, J.

    2011-01-01

    -09-02 REGIONAL ENERGY BASELINE (1960 ~ 2009) 0 100 200 300 400 500 600 700 800 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 To tal En erg y U se pe r C ap ita (M MB tu) Year Total Energy Use per Capita (1960-2009) US... SEEC 12-States TX Hyojin Kim Juan-Carlos Baltazar, Ph.D. Jeff S. Haberl, Ph.D., P.E. September 2011 ENERGY SYSTEMS LABORATORY Texas Engineering Experiment Station Texas A&M University System 1960-2009 Regional Energy...

  8. Uplifted supersymmetric Higgs region

    E-Print Network [OSTI]

    Bogdan A. Dobrescu; Patrick J. Fox

    2010-05-26

    We show that the parameter space of the Minimal Supersymmetric Standard Model includes a region where the down-type fermion masses are generated by the loop-induced couplings to the up-type Higgs doublet. In this region the down-type Higgs doublet does not acquire a vacuum expectation value at tree level, and has sizable couplings in the superpotential to the tau leptons and bottom quarks. Besides a light standard-like Higgs boson, the Higgs spectrum includes the nearly degenerate states of a heavy spin-0 doublet which can be produced through their couplings to the $b$ quark and decay predominantly into \\tau^+\\tau^- or \\tau\

  9. Regional companies eye growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II) by Carbon-RichProtonAbout UsRegional companies eye growth Regional

  10. Final report for CCS cross-layer reliability visioning study

    SciTech Connect (OSTI)

    Quinn, Heather M; Dehon, Andre; Carter, Nicj

    2010-12-20

    The geometric rate of improvement of transistor size and integrated circuit performance known as Moore's Law has been an engine of growth for our economy, enabling new products and services, creating new value and wealth, increasing safety, and removing menial tasks from our daily lives. Affordable, highly integrated components have enabled both life-saving technologies and rich entertainment applications. Anti-lock brakes, insulin monitors, and GPS-enabled emergency response systems save lives. Cell phones, internet appliances, virtual worlds, realistic video games, and mp3 players enrich our lives and connect us together. Over the past 40 years of silicon scaling, the increasing capabilities of inexpensive computation have transformed our society through automation and ubiquitous communications. Looking forward, increasing unpredictability threatens our ability to continue scaling integrated circuits at Moore's Law rates. As the transistors and wires that make up integrated circuits become smaller, they display both greater differences in behavior among devices designed to be identical and greater vulnerability to transient and permanent faults. Conventional design techniques expend energy to tolerate this unpredictability by adding safety margins to a circuit's operating voltage, clock frequency or charge stored per bit. However, the rising energy costs needed to compensate for increasing unpredictability are rapidly becoming unacceptable in today's environment where power consumption is often the limiting factor on integrated circuit performance and energy efficiency is a national concern. Reliability and energy consumption are both reaching key inflection points that, together, threaten to reduce or end the benefits of feature size reduction. To continue beneficial scaling, we must use a cross-layer, Jull-system-design approach to reliability. Unlike current systems, which charge every device a substantial energy tax in order to guarantee correct operation in spite of rare events, such as one high-threshold transistor in a billion or one erroneous gate evaluation in an hour of computation, cross-layer reliability schemes make reliability management a cooperative effort across the system stack, sharing information across layers so that they only expend energy on reliability when an error actually occurs. Figure 1 illustrates an example of such a system that uses a combination of information from the application and cheap architecture-level techniques to detect errors. When an error occurs, mechanisms at higher levels in the stack correct the error, efficiently delivering correct operation to the user in spite of errors at the device or circuit levels. In the realms of memory and communication, engineers have a long history of success in tolerating unpredictable effects such as fabrication variability, transient upsets, and lifetime wear using information sharing, limited redundancy, and cross-layer approaches that anticipate, accommodate, and suppress errors. Networks use a combination of hardware and software to guarantee end-toend correctness. Error-detection and correction codes use additional information to correct the most common errors, single-bit transmission errors. When errors occur that cannot be corrected by these codes, the network protocol requests re-transmission of one or more packets until the correct data is received. Similarly, computer memory systems exploit a cross-layer division of labor to achieve high performance with modest hardware. Rather than demanding that hardware alone provide the virtual memory abstraction, software page-fault and TLB-miss handlers allow a modest piece of hardware, the TLB, to handle the common-case operations on a cyc1e-by-cycle basis while infrequent misses are handled in system software. Unfortunately, mitigating logic errors is not as simple or as well researched as memory or communication systems. This lack of understanding has led to very expensive solutions. For example, triple-modular redundancy masks errors by triplicating computations in either time or area. T

  11. Multilateral, regional and bilateral energy trade governance

    SciTech Connect (OSTI)

    Leal-Arcas, Rafael; Grasso, Costantino; Rios, Juan Alemany )

    2014-12-01

    The current international energy trade governance system is fragmented and multi-layered. Streamlining it for greater legal cohesiveness and international political and economic cooperation would promote global energy security. The current article explores three levels of energy trade governance: multilateral, regional and bilateral. Most energy-rich countries are part of the multilateral trading system, which is institutionalized by the World Trade Organization (WTO). The article analyzes the multilateral energy trade governance system by focusing on the WTO and energy transportation issues. Regionally, the article focuses on five major regional agreements and their energy-related aspects and examines the various causes that explain the proliferation of regional trade agreements, their compatibility with WTO law, and then provides several examples of regional energy trade governance throughout the world. When it comes to bilateral energy trade governance, this article only addresses the European Unionís (EU) bilateral energy trade relations. The article explores ways in which gaps could be filled and overlaps eliminated whilst remaining true to the high-level normative framework, concentrating on those measures that would enhance EU energy security.

  12. REGIONAL TRAVEL MAPS Philadelphia

    E-Print Network [OSTI]

    Gilchrist, James F.

    REGIONAL TRAVEL MAPS 2 hrs. 1 hr. 3 hrs. 4 hrs. 5 hrs. Philadelphia New York City Pittsburgh BostonReadingand Harrisburg 476 476 276 309 309 663 378 309 33 78 80 80 LEHIGH UNIVERSITY Bethlehem Quakertown to Philadelphia Coast including Philadelphia (50 miles south) and New York City (90 miles northeast). Bethlehem

  13. Prince George Forest Region

    E-Print Network [OSTI]

    Coxson, Darwyn

    Prince George Forest Region Forest Resources & Practices Team May 1999 Note #PG-20 ∑ ExtensionAssociate,UniversityofNorthern BritishColumbia 2 MSc, RPBio, Silvifauna Research, Prince George, BC 3 PhD, R.M. Sagar and Associates, Prince George, BC #12;Ministry of Forests, 5th Floor, 1011 - 4th Avenue, Prince George, BC V2L 3H9

  14. A reliability and mass perspective of SP-100 Stirling cycle lunar-base powerplant designs

    SciTech Connect (OSTI)

    Bloomfield, H.S.

    1991-06-01

    The purpose was to obtain reliability and mass perspectives on selection of space power system conceptual designs based on SP-100 reactor and Stirling cycle power-generation subsystems. The approach taken was to: (1) develop a criterion for an acceptable overall reliability risk as a function of the expected range of emerging technology subsystem unit reliabilities; (2) conduct reliability and mass analyses for a diverse matrix of 800-kWe lunar-base design configurations employing single and multiple powerplants with both full and partial subsystem redundancy combinations; and (3) derive reliability and mass perspectives on selection of conceptual design configurations that meet an acceptable reliability criterion with the minimum system mass increase relative to reference powerplant design. The developed perspectives provided valuable insight into the considerations required to identify and characterize high-reliability and low-mass lunar-base powerplant conceptual design.

  15. Air Pollution and Mortality: Estimating Regional and National DoseResponse Relationships

    E-Print Network [OSTI]

    Dominici, Francesca

    Air Pollution and Mortality: Estimating Regional and National Dose≠Response Relationships Francesca pollution and mortality for the 88 largest U.S. cities for the period 1987≠1994, to estimate relative rates the dependence of relative mortality rates on mean pollution levels, demographic variables, reliability

  16. Regional Community Wind Conferences, Great Plains Windustry Project

    SciTech Connect (OSTI)

    Daniels, Lisa [Windustry

    2013-02-28

    Windustry organized and produced five regional Community Wind Across America (CWAA) conferences in 2010 and 2011 and held two CWAA webinars in 2011 and 2012. The five conferences were offered in regions throughout the United States: Denver, Colorado ¬? October 2010 St. Paul, Minnesota ¬? November 2010 State College, Pennsylvania ¬? February 2011 Ludington, Michigan (co-located with the Michigan Energy Fair) June 2011 Albany, New York October 2011

  17. Note: Reliable low-vibration piezo-mechanical shutter

    SciTech Connect (OSTI)

    Bauer, Michael, E-mail: mibauer@physik.uni-kl.de; Franzreb, Philipp Pierre; Widera, Artur [Department of Physics and State-Research Center OPTIMAS, University of Kaiserslautern, 67663 Kaiserslautern (Germany); Spethmann, Nicolas [Department of Physics, University of California, Berkeley, California 94720 (United States)

    2014-09-15

    We present a mechanical shutter based on a bending piezo-actuator. The shutter features an active aperture of about 2 mm, allowing for full extinction and lossless transmission of a beam. Acoustic noise and mechanical vibrations produced are very low and the shutter is outstandingly long-lived; a test device has undergone 20 ◊ 10{sup 6} cycles without breaking. A reflector makes the shutter capable of reliably interrupting a beam with at least 2 W of cw power at 780 nm. The shutter is well suited to create pulses as short as 16 ms, while pulse lengths down to 1 ms are possible. The rise and fall times are approximately 120 Ķs, with a delay of 2 ms. Jitter stays below 10 Ķs, while long-term drifts stay well below 500 Ķs.

  18. Module Packaging Research and Reliability: Activities and Capabilities

    SciTech Connect (OSTI)

    McMahon, T. J.; delCueto, J.; Glick, S.; Jorgensen, G.; Kempe, M.; Pern, J.; Terwilliger, K.

    2005-11-01

    Our team activities are directed at improving PV module reliability by incorporating new, more effective, and less expensive packaging materials and techniques. New and existing materials or designs are evaluated before and during accelerated environmental exposure for the following properties: (1) Adhesion and cohesion: peel strength and lap shear. (2) Electrical conductivity: surface, bulk, interface and transients. (3) Water vapor transmission: solubility and diffusivity. (4) Accelerated weathering: ultraviolet, temperature, and damp heat tests. (5) Module and cell failure diagnostics: infrared imaging, individual cell shunt characterization, coring. (6) Fabrication improvements: SiOxNy barrier coatings and enhanced wet adhesion. (7) Numerical modeling: Moisture ingress/egress, module and cell performance, and cell-to-frame leakage current. (8) Rheological properties of polymer encapsulant and sheeting materials. Specific examples are described.

  19. Nuclear electric propulsion operational reliability and crew safety study

    SciTech Connect (OSTI)

    Karns, J.J.; Fragola, J.R.; Kahan, L.; Pelaccio, D. (Science Applications International Corporation, 8 W 40th St., 14th Floor, New York, New York 10018 (United States))

    1993-01-20

    The central purpose of this analysis is to assess the achievability'' of a nuclear electric propulsion (NEP) system in a given mission. Achievability'' is a concept introduced to indicate the extent to which a system that meets or achieves its design goals might be implemented using the existing technology base. In the context of this analysis, the objective is to assess the achievability of an NEP system for a manned Mars mission as it pertains to operational reliability and crew safety goals. By varying design parameters, then examining the resulting system achievability, the design and mission risk drivers can be identified. Additionally, conceptual changes in design approach or mission strategy which are likely to improve overall achievability of the NEP system can be examined.

  20. IDHEAS Ė A NEW APPROACH FOR HUMAN RELIABILITY ANALYSIS

    SciTech Connect (OSTI)

    G. W. Parry; J.A Forester; V.N. Dang; S. M. L. Hendrickson; M. Presley; E. Lois; J. Xing

    2013-09-01

    This paper describes a method, IDHEAS (Integrated Decision-Tree Human Event Analysis System) that has been developed jointly by the US NRC and EPRI as an improved approach to Human Reliability Analysis (HRA) that is based on an understanding of the cognitive mechanisms and performance influencing factors (PIFs) that affect operator responses. The paper describes the various elements of the method, namely the performance of a detailed cognitive task analysis that is documented in a crew response tree (CRT), and the development of the associated time-line to identify the critical tasks, i.e. those whose failure results in a human failure event (HFE), and an approach to quantification that is based on explanations of why the HFE might occur.