Powered by Deep Web Technologies
Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Acoustic paramagnetic logging tool  

DOE Patents (OSTI)

New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth3 s magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation . The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores.

Vail, III, William B. (Bothell, WA)

1988-01-01T23:59:59.000Z

2

Dual excitation acoustic paramagnetic logging tool  

DOE Patents (OSTI)

New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be performed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described. 6 figs.

Vail, W.B. III.

1989-02-14T23:59:59.000Z

3

Dual excitation acoustic paramagnetic logging tool  

DOE Patents (OSTI)

New methods and apparatus are disclosed which allow measurement of the presence of oil and water in gelogical formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleous present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described.

Vail, III, William B. (Bothell, WA)

1989-01-01T23:59:59.000Z

4

Building Energy Software Tools Directory: Acoustics Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Acoustics Program Developed to help designers accurately model the sound level reaching building tenant's ears, the Trane Acoustics Program (TAP) "projects" equipment sound power...

5

Building Energy Software Tools Directory: Acoustics Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Acoustics Program Acoustics Program Developed to help designers accurately model the sound level reaching building tenant's ears, the Trane Acoustics Program (TAP) "projects" equipment sound power data through the surroundings (e.g., floors, ductwork, walls), to estimate the sound level that will be heard. Industry-standard calculations published by ASHRAE's 1991 Algorithms for HVAC Acoustics handbook are the basis for this estimate. In TAP, you can model the conditions of an HVAC system by choosing specific equipment and building component criteria. TAP will analyze the sound path and calculate the total effect for the enclosed space. You can continuously adjust the data and system design criteria to compare the results effortlessly. TAP will even plot presentation quality graphs of

6

Building Energy Software Tools Directory: Acoustics Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Building Energy Software Tools Directory EERE Building Technologies Office Building Energy Software Tools Directory Printable Version Share this resource Home About the...

7

Building Energy Software Tools Directory: Acoustics Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Printable Version Share this resource Home About the Directory Tools by Subject Whole Building Analysis Codes & Standards Materials, Components, Equipment, & Systems Envelope...

8

Sea Level Rise Tool For Sandy Recovery  

NLE Websites -- All DOE Office Websites (Extended Search)

and related professional communities (e.g., local chapters of associations such as ASCE, ASFPM, APA, etc.) 4. What counties are include in this sea level rise tool? Answer In...

9

Building Energy Software Tools Directory: AcousticCalc  

NLE Websites -- All DOE Office Websites (Extended Search)

AcousticCalc AcousticCalc Developed over the last decade, AcousticCalc helps designers predict sound levels at the room level from a distant sound source. The program uses the ASHRAE Handbook and ASHRAE's 1991 Algorithms for HVAC Acoustics handbook methods with the "Source-Path-Receiver" model. This easy-to-use Windows-based program allows a user to define and save unlimited number of sound sources, save and define unlimited number of sound "paths" (composed of long list of possible duct component types) and model the ceiling effect and three different models for room effect. AcousticCalc allows a user to import and export (share) sound sources, user-defined devices, terminal units, and duct silencers with other users. Easy-to-navigate "tree" modeling allows an unlimited number of sound

10

Feasibility of using acoustic emission to determine in-process tool wear  

SciTech Connect

Acoustic emission (AE) was evaluated for its ability to predict and recognize failure of cutting tools during machining processes when the cutting tool rotates and the workpiece is stationary. AE output was evaluated with a simple algorithm. AE was able to detect drill failure when the transducer was mounted on the workpiece holding fixture. Drill failure was recognized as size was reduced to 0.0003 in. diameter. The ability to predict failure was reduced with drill size, drill material elasticity, and tool coating. AE output for the turning process on a lathe was compared to turning tool insert wear. The turning tool must have sufficient wear to produce a detectable change in AE output to predict insert failure.

Lazarus, L.J.

1996-04-01T23:59:59.000Z

11

Acoustic methods for detecting water-filled fractures using commercial logging tools  

DOE Green Energy (OSTI)

The Los Alamos Scientific Laboratory Hot Dry Rock Geothermal Energy Development Project, under the Department of Energy and in cooperation with Dresser Atlas, has conducted single- and dual-well acoustic measurements to detect fractures in the artificial geothermal reservoir at the Fenton Hill New Mexico experimental site. The measurements were made using modified Dresser Atlas logging tools. Signals traversed distances of from 48 to 150 feet between two wells. Signals intersecting hydraulic fractures in the reservoir under both hydrostatic and pressurized conditions were simultaneously detected in both wells. Upon reservoir pressurization, signals along many ray paths were severely attenuated throughout their entire coda. In addition obvious shear wave arrivals were notably absent. The signals were processed to obtain Full-Wave Acoustic, Power, and Normalized Equi-Power Logs. Analysis of these logs identified the effective ''top'' of a region of hydraulically activated fractures and fractures intersecting the injection well behind casing.

Albright, J.N.; Aamodt, R.L.; Potter, R.M.; Spence, R.W.

1978-01-01T23:59:59.000Z

12

DRAFT OF THE REPORTING TOOL DETAILS FOR RECOVERY ACT REPORTING REQUIREMENTS  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

GUIDANCE OF THE REPORTING TOOL DETAILS FOR RECOVERY ACT GUIDANCE OF THE REPORTING TOOL DETAILS FOR RECOVERY ACT REPORTING REQUIREMENTS FROM OFPP 1) Providing Information to Contractors a) The registration process developed for the tool will use the Central Contractor Registration (CCR) Point of Contact (POC) to authorize those registering in the system for a particular DUNS number in preparation for the report due October 10, 2009. A message was sent on August 17, 2009 to CCR POCs associated with Recovery Act contract actions reported in the Federal Procurement Data System-Next Generation (FPDS-NG). The message advised the CCR POC to review the registration and authorization information available at federalreporting.gov. A Federal Register notice was published on August 25th to encourage contractors to register early at federalreporting.gov. (FR 42877, August 25, 2009)

13

A Management Tool for Analyzing CHP Natural Gas Liquids Recovery System  

E-Print Network (OSTI)

The objective of this research is to develop a management tool for analyzing combined heat and power (CHP) natural gas liquids (NGL) recovery systems. The methodology is developed around the central ideas of product recovery, possible recovery levels, and the flexibility of the process. These ideas led to the design of the CHP-NGL recovery system and the development of the equipment sizing and economic analysis methods. Requirements for sizing refrigeration units, heat exchangers, and pumps are discussed and demonstrated. From the data sheets it is possible to gather costs associated with the project and demonstrate the economic feasibility of the system. The amount of NGL recovered, heating value, payback period, cash flow, net present value of money, and the internal rate of return are calculated and demonstrated to be favorable to this project.

Olsen, C.; Kozman, T. A.; Lee, J.

2008-01-01T23:59:59.000Z

14

Geochemical engineering design tools for uranium in situ recovery : the HYDROGEOCHEM codes.  

SciTech Connect

Geochemical Engineering Design (GED) is based on applications of the principles and various computer models that describe the biogeochemistry and physics of removal of contaminants from water by adsorption, precipitation and filtration. It can be used to optimize or evaluate the efficiency of all phases of in situ recovery (ISR). The primary tools of GED are reactive transport models; this talk describes the potential application of the HYDROGEOCHEM family of codes to ISR. The codes can describe a complete suite of equilibrium or kinetic aqueous complexation, adsorption-desorption, precipitation-dissolution, redox, and acid-base reactions in variably saturated media with density-dependent fluid flow. Applications to ISR are illustrated with simulations of (1) the effectiveness of a reactive barrier to prevent off-site uranium migration and (2) evaluation of the effect of sorption hysteresis on natural attenuation. In the first example, it can be seen that the apparent effectiveness of the barrier depends on monitoring location and that it changes over time. This is due to changes in pH, saturation of sorption sites, as well as the geometry of the flow field. The second simulation shows how sorption hysteresis leads to observable attenuation of a uranium contamination plume. Different sorption mechanisms including fast (or reversible), slow, and irreversible sorption were simulated. The migration of the dissolved and total uranium plumes for the different cases are compared and the simulations show that when 50-100% of the sites have slow desorption rates, the center of mass of the dissolved uranium plume begins to move upstream. This would correspond to the case in which the plume boundaries begin to shrink as required for demonstration of natural attenuation.

Siegel, Malcolm Dean; Li, Ming-Hsu (National Central University, Jhongli City, Taiwan); Yeh, Gour-Tsyh (University of Central Florida, Orlando, FL)

2010-11-01T23:59:59.000Z

15

IX Encontro de tecnologia em Acstica Submarina IX ETAS FIELD CALIBRATION A TOOL FOR ACOUSTIC NOISE PREDICTION  

E-Print Network (OSTI)

, as in our case, the problem of predicting the distribution of acoustic noise due to a wave energy power farms, will likely grow in the future. Such a power plant, composed by several generators, will produce management policies. In the other hand there is an increasing demand for wave energy installations that

Jesus, Sérgio M.

16

Space, time and acoustics  

E-Print Network (OSTI)

This thesis describes the development of new concepts in acoustical analysis from their inception to implementation as a computer design tool. Research is focused on a computer program which aids the designer to visually ...

Thompson, Philip R. Z. (Philip Reed Zane)

1988-01-01T23:59:59.000Z

17

Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Maintenance CalendarOutages is the tool to schedule network maintenance and troubleshooting. I've got network trouble. Help me out trouble@es.net is a quick and easy way to...

18

Acoustic telemetry.  

Science Conference Proceedings (OSTI)

Broadcasting messages through the earth is a daunting task. Indeed, broadcasting a normal telephone conversion through the earth by wireless means is impossible with todays technology. Most of us don't care, but some do. Industries that drill into the earth need wireless communication to broadcast navigation parameters. This allows them to steer their drill bits. They also need information about the natural formation that they are drilling. Measurements of parameters such as pressure, temperature, and gamma radiation levels can tell them if they have found a valuable resource such as a geothermal reservoir or a stratum bearing natural gas. Wireless communication methods are available to the drilling industry. Information is broadcast via either pressure waves in the drilling fluid or electromagnetic waves in the earth and well tubing. Data transmission can only travel one way at rates around a few baud. Given that normal Internet telephone modems operate near 20,000 baud, these data rates are truly very slow. Moreover, communication is often interrupted or permanently blocked by drilling conditions or natural formation properties. Here we describe a tool that communicates with stress waves traveling through the steel drill pipe and production tubing in the well. It's based on an old idea called Acoustic Telemetry. But what we present here is more than an idea. This tool exists, it's drilled several wells, and it works. Currently, it's the first and only acoustic telemetry tool that can withstand the drilling environment. It broadcasts one way over a limited range at much faster rates than existing methods, but we also know how build a system that can communicate both up and down wells of indefinite length.

Drumheller, Douglas Schaeffer; Kuszmaul, Scott S.

2003-08-01T23:59:59.000Z

19

Acoustical properties of drill strings  

DOE Green Energy (OSTI)

The recovery of petrochemical and geothermal resources requires extensive drilling of wells to increasingly greater depths. Real-time collection and telemetry of data about the drilling process while it occurs thousands of feet below the surface is an effective way of improving the efficiency of drilling operations. Unfortunately, due to hostile down-hole environments, telemetry of this data is an extremely difficult problem. Currently, commercial systems transmit data to the surface by producing pressure pulses within the portion of the drilling mud enclosed in the hollow steel drill string. Transmission rates are between two and four data bits per second. Any system capable of raising data rates without increasing the complexity of the drilling process will have significant economic impact. One alternative system is based upon acoustical carrier waves generated within the drill string itself. If developed, this method would accommodate data rates up to 100 bits per second. Unfortunately, the drill string is a periodic structure of pipe and threaded tool joints, the transmission characteristics are very complex and exhibit a banded and dispersive structure. Over the past forty years, attempts to field systems based upon this transmission method have resulted in little success. This paper examines this acoustical transmission problem in great detail. The basic principles of acoustic wave propagation in the periodic structure of the drill string are examined through theory, laboratory experiment, and field test. The results indicate the existence of frequency bands which are virtually free of attenuation and suitable for data transmission at high bit rates. 9 refs., 38 figs., 2 tabs.

Drumheller, D.S.

1988-08-01T23:59:59.000Z

20

Underwater Nonlinear Acoustic Speaker.  

E-Print Network (OSTI)

??In this work an acoustic parametric array for underwater use was designed, built and tested. An acoustic parametric array creates a focused beam of sound… (more)

Andersson, Sara

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Early Tube Leak Detection in a HRSG Application Using Acoustic Monitoring Technology  

Science Conference Proceedings (OSTI)

Acoustic monitoring has become an essential part of early tube leak detection for conventional boilers. Acoustic monitoring is intended for steam leak detection in pressurized vessels, including power boilers, recovery boilers, and feedwater heaters. The system performs acoustic monitoring by continuously measuring the internal sounds from the boiler, signaling an alarm when the sound exceeds a preset threshold for a ...

2012-12-12T23:59:59.000Z

22

Documenting Catastrophic Mortality and Recovery on Coral Reefs in Response to Cold Water: Using Underwater Landscape Mosaics as a Tool for Coral Reef Monitoring.  

E-Print Network (OSTI)

??Traditional coral reef monitoring protocols may be underestimating mortality and recovery dynamics on coral reefs. The primary target of these protocols, Scleractinian corals, represents an… (more)

Cantwell, Kasey L

2013-01-01T23:59:59.000Z

23

Acoustic transducer  

DOE Patents (OSTI)

An acoustic transducer is described comprising a one-piece hollow mandrel into the outer surface of which is formed a recess with sides perpendicular to the central axis of the mandrel and separated by a first distance and with a bottom parallel to the central axis and within which recess are a plurality of washer-shaped discs of a piezoelectric material and at least one disc of a temperature-compensating material with the discs being captured between the sides of the recess in a pre-stressed interference fit, typically at 2,000 psi of compressive stress. The transducer also includes a power supply and means to connect to a measurement device. The transducer is intended to be used for telemetry between a measurement device located downhole in an oil or gas well and the surface. The transducer is of an construction that is stronger with fewer joints that could leak fluids into the recess holding the piezoelectric elements than is found in previous acoustic transducers. 4 figs.

Drumheller, D.S.

1997-12-30T23:59:59.000Z

24

Acoustic transducer  

DOE Patents (OSTI)

An acoustic transducer comprising a one-piece hollow mandrel into the outer surface of which is formed a recess with sides perpendicular to the central axis of the mandrel and separated by a first distance and with a bottom parallel to the central axis and within which recess are a plurality of washer-shaped discs of a piezoelectric material and at least one disc of a temperature-compensating material with the discs being captured between the sides of the recess in a pre-stressed interference fit, typically at 2000 psi of compressive stress. The transducer also includes a power supply and means to connect to a measurement device. The transducer is intended to be used for telemetry between a measurement device located downhole in an oil or gas well and the surface. The transducer is of an construction that is stronger with fewer joints that could leak fluids into the recess holding the piezoelectric elements than is found in previous acoustic transducers.

Drumheller, Douglas S. (Cedar Crest, NM)

1997-01-01T23:59:59.000Z

25

Acoustic cryocooler  

DOE Patents (OSTI)

An acoustic cryocooler with no moving parts is formed from a thermoacoustic driver (TAD) driving a pulse tube refrigerator (PTR) through a standing wave tube. Thermoacoustic elements in the TAD are spaced apart a distance effective to accommodate the increased thermal penetration length arising from the relatively low TAD operating frequency in the range of 15-60 Hz. At these low operating frequencies, a long tube is required to support the standing wave. The tube may be coiled to reduce the overall length of the cryocooler. One or two PTR's are located on the standing wave tube adjacent antinodes in the standing wave to be driven by the standing wave pressure oscillations. It is predicted that a heat input of 1000 W at 1000 K will maintain a cooling load of 5 W at 80 K. 3 figs.

Swift, G.W.; Martin, R.A.; Radebaugh, R.

1989-09-26T23:59:59.000Z

26

Acoustic cryocooler  

DOE Patents (OSTI)

An acoustic cryocooler with no moving parts is formed from a thermoacoustic driver (TAD) driving a pulse tube refrigerator (PTR) through a standing wave tube. Thermoacoustic elements in the TAD are spaced apart a distance effective to accommodate the increased thermal penetration length arising from the relatively low TAD operating frequency in the range of 15-60 Hz. At these low operating frequencies, a long tube is required to support the standing wave. The tube may be coiled to reduce the overall length of the cryocooler. One or two PTR's are located on the standing wave tube adjacent antinodes in the standing wave to be driven by the standing wave pressure oscillations. It is predicted that a heat input of 1000 W at 1000 K will maintian a cooling load of 5 W at 80 K.

Swift, Gregory W. (Santa Fe, NM); Martin, Richard A. (Los Alamos, NM); Radenbaugh, Ray (Louisville, CO)

1990-01-01T23:59:59.000Z

27

THERMAL RECOVERY  

NLE Websites -- All DOE Office Websites (Extended Search)

THERMAL RECOVERY Thermal recovery comprises the techniques of steamflooding, cyclic steam stimulation, and in situ combustion. In steamflooding, high-temperature steam is injected...

28

Building Energy Software Tools Directory: Acoustics Program  

NLE Websites -- All DOE Office Websites (Extended Search)

by Subject Whole Building Analysis Codes & Standards Materials, Components, Equipment, & Systems Other Applications Atmospheric Pollution Energy Economics Indoor Air Quality...

29

Modeling of Salivary Production Recovery After Radiotherapy Using Mixed Models: Determination of Optimal Dose Constraint for IMRT Planning and Construction of Convenient Tools to Predict Salivary Function  

Science Conference Proceedings (OSTI)

Purpose: The mathematical relationship between the dose to the parotid glands and salivary gland production needs to be elucidated. This study, which included data from patients included in a French prospective study assessing the benefit of intensity-modulated radiotherapy (RT), sought to elaborate a convenient and original model of salivary recovery. Methods and Materials: Between January 2001 and December 2004, 44 patients were included (35 with oropharyngeal and 9 with nasopharyngeal cancer). Of the 44 patients, 24 were treated with intensity-modulated RT, 17 with three-dimensional conformal RT, and 2 with two-dimensional RT. Stimulated salivary production was collected for {gland were modeled using a mixed model. Several models were developed to assess the best-fitting variable for the dose level to the parotid gland. Results: Models developed with the dose to the contralateral parotid fit the data slightly better than those with the dose to both parotids, suggesting that contralateral and ipsilateral parotid glands are not functionally equivalent even with the same dose level to the glands. The best predictive dose-value variable for salivary flow recovery was the volume of the contralateral parotid gland receiving >40 Gy. Conclusion: The results of this study show that the recommendation of a dose constraint for intensity-modulated RT planning should be established at the volume of the contralateral parotid gland receiving >40 Gy rather than the mean dose. For complete salivary production recovery after 24 months, the volume of the contralateral parotid gland receiving >40 Gy should be gland.

Ortholan, Cecile [Department of Radiotherapy, Centre Antoine-Lacassagne, Canceropole PACA, Nice (France)], E-mail: c.ortholan@wanadoo.fr; Chamorey, Emmanuel Phar [Department of Biostatistics, Centre Antoine-Lacassagne, Canceropole PACA, Nice (France); Benezery, Karen; Thariat, Juliette [Department of Radiotherapy, Centre Antoine-Lacassagne, Canceropole PACA, Nice (France); Dassonville, Olivier; Poissonnet, Gilles; Bozec, Alexandre [Department of Otolaryngology, Head and Neck Surgery, Centre Antoine-Lacassagne, Canceropole PACA, Nice (France); Follana, Philippe; Peyrade, Frederique [Department of Medical Oncology, Centre Antoine-Lacassagne, Canceropole PACA, Nice (France); Sudaka, Anne [Department of Pathology, Centre Antoine-Lacassagne, Canceropole PACA, Nice (France); Gerard, Jean Pierre; Bensadoun, Rene Jean [Department of Radiotherapy, Centre Antoine-Lacassagne, Canceropole PACA, Nice (France)

2009-01-01T23:59:59.000Z

30

Building Energy Software Tools Directory: Tools by Subject - Other  

NLE Websites -- All DOE Office Websites (Extended Search)

Misc Applications Misc Applications A B C D E F G I K L M O P Q R S T U Tool Applications Free Recently Updated ACOUSALLE acoustics, codes and standards AcousticCalc HVAC acoustics, sound level prediction, noise level Acoustics Program HVAC acoustics, sound level prediction, noise level Software has been updated. AEPS System Planning electrical system, renewable energy system, planning and design software, modeling, simulation, energy usage, system performance, financial analysis, solar, wind, hydro, behavior characteristics, usage profiles, generation load storage calculations, on-grid, off-grid, residential, commercial, system sizing, utility rate plans, rate comparison, utility costs, energy savings Software has been updated. Animate animated visualization of data, XY graphs, energy-use data

31

Building Energy Software Tools Directory: Tools by Platform - PC  

NLE Websites -- All DOE Office Websites (Extended Search)

PC PC 1 3 A B C D E F G H I J K L M N O P Q R S T U V W Z ¡ Tool Applications Free Recently Updated 1D-HAM heat, air, moisture transport, walls Software has been updated. 3E Plus insulation, insulation thickness Free software. Software has been updated. AAMASKY skylights, daylighting, commercial buildings ABACODE Residential code compliance, IECC Free software. ACOUSALLE acoustics, codes and standards AcousticCalc HVAC acoustics, sound level prediction, noise level Acoustics Program HVAC acoustics, sound level prediction, noise level Software has been updated. Acuity Energy Platform energy efficiency software; customized business recommendation; commercial and industrial energy use comparisons Software has been updated. ADELINE

32

Acoustic Microscopy Applications*  

Science Conference Proceedings (OSTI)

Figure: ...Fig. 17 A portion of the 160 mm 2 (0.25 in. 2 ) area of an alumina ceramic disk scanned by an acoustic microscope

33

Acoustics by additive manufacturing.  

E-Print Network (OSTI)

??This study focuses on exploring the merging field of additive manufacturing and acoustics and introduces a new type of sound absorber which is regulating performance… (more)

Setaki, F.

2012-01-01T23:59:59.000Z

34

Energy Storage Computational Tool | Open Energy Information  

Open Energy Info (EERE)

Energy Storage Computational Tool Energy Storage Computational Tool Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Energy Storage Computational Tool Agency/Company /Organization: Navigant Consulting Sector: Energy Focus Area: Grid Assessment and Integration Resource Type: Software/modeling tools User Interface: Desktop Application Website: www.smartgrid.gov/recovery_act/program_impacts/energy_storage_computat Country: United States Web Application Link: www.smartgrid.gov/recovery_act/program_impacts/energy_storage_computat Cost: Free Northern America Language: English Energy Storage Computational Tool Screenshot References: Energy Storage Computational Tool[1] SmartGrid.gov[2] Logo: Energy Storage Computational Tool This tool is used for identifying, quantifying, and monetizing the benefits

35

Building Energy Software Tools Directory: Tools by Subject - Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Hvac Systems Hvac Systems 3 A B C D E F G H I J K L M N O P Q R S T V Tool Applications Free Recently Updated 3E Plus insulation, insulation thickness Free software. Software has been updated. AcousticCalc HVAC acoustics, sound level prediction, noise level Acoustics Program HVAC acoustics, sound level prediction, noise level Software has been updated. AFT Fathom design, pump selection, pipe analysis, duct design, duct sizing, chilled water systems, hot water system Software has been updated. AFT Mercury optimization, pipe optimization, pump selection, duct design, duct sizing, chilled water systems, hot water systems AIRWIND Pro Air Conditioning Load Calculation Analysis Platform heating, cooling, and SWH equipment, commercial buildings

36

Acoustic cooling engine  

DOE Patents (OSTI)

An acoustic cooling engine with improved thermal performance and reduced internal losses comprises a compressible fluid contained in a resonant pressure vessel. The fluid has a substantial thermal expansion coefficient and is capable of supporting an acoustic standing wave. A thermodynamic element has first and second ends and is located in the resonant pressure vessel in thermal communication with the fluid. The thermal response of the thermodynamic element to the acoustic standing wave pumps heat from the second end to the first end. The thermodynamic element permits substantial flow of the fluid through the thermodynamic element. An acoustic driver cyclically drives the fluid with an acoustic standing wave. The driver is at a location of maximum acoustic impedance in the resonant pressure vessel and proximate the first end of the thermodynamic element. A hot heat exchanger is adjacent to and in thermal communication with the first end of the thermodynamic element. The hot heat exchanger conducts heat from the first end to portions of the resonant pressure vessel proximate the hot heat exchanger. The hot heat exchanger permits substantial flow of the fluid through the hot heat exchanger. The resonant pressure vessel can include a housing less than one quarter wavelength in length coupled to a reservoir. The housing can include a reduced diameter portion communicating with the reservoir. The frequency of the acoustic driver can be continuously controlled so as to maintain resonance.

Hofler, Thomas J. (Los Alamos, NM); Wheatley, John C. (Los Alamos, NM); Swift, Gregory W. (Santa Fe, NM); Migliori, Albert (Santa Fe, NM)

1988-01-01T23:59:59.000Z

37

EMSL: Capabilities: American Recovery and Reinvestment Act  

NLE Websites -- All DOE Office Websites (Extended Search)

American Recovery and Reinvestment Act American Recovery and Reinvestment Act Recovery Act Logo EMSL researchers are benefitting from a recent $60 million investment in innovation through the American Recovery and Reinvestment Act. These Recovery Act funds were employed to further develop and deploy transformational capabilities that deliver scientific discoveries in support of DOE's mission. Today, they are helping EMSL accomplish the following: Establish leadership in in situ chemical imaging and procure ultrahigh-resolution microscopy tools Additional Information Investing in Innovation: EMSL and the American Recovery and Reinvestment Act Recovery Act and Systems Biology at EMSL Recovery Act Instruments coming to EMSL In the News EMSL ARRA Capability Features News: Recovery Act and PNNL Recovery Act in the Tri-City Herald

38

Acoustical heat pumping engine  

DOE Patents (OSTI)

The disclosure is directed to an acoustical heat pumping engine without moving seals. A tubular housing holds a compressible fluid capable of supporting an acoustical standing wave. An acoustical driver is disposed at one end of the housing and the other end is capped. A second thermodynamic medium is disposed in the housing near to but spaced from the capped end. Heat is pumped along the second thermodynamic medium toward the capped end as a consequence both of the pressure oscillation due to the driver and imperfect thermal contact between the fluid and the second thermodynamic medium.

Wheatley, John C. (Los Alamos, NM); Swift, Gregory W. (Los Alamos, NM); Migliori, Albert (Santa Fe, NM)

1983-08-16T23:59:59.000Z

39

Acoustical heat pumping engine  

DOE Patents (OSTI)

The disclosure is directed to an acoustical heat pumping engine without moving seals. A tubular housing holds a compressible fluid capable of supporting an acoustical standing wave. An acoustical driver is disposed at one end of the housing and the other end is capped. A second thermodynamic medium is disposed in the housing near to but spaced from the capped end. Heat is pumped along the second thermodynamic medium toward the capped end as a consequence both of the pressure oscillation due to the driver and imperfect thermal contact between the fluid and the second thermodynamic medium. 2 figs.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1983-08-16T23:59:59.000Z

40

Acoustic well cleaner  

DOE Patents (OSTI)

A method and apparatus are disclosed for cleaning the wellbore and the near wellbore region. A sonde is provided which is adapted to be lowered into a borehole and which includes a plurality of acoustic transducers arranged around the sonde. Electrical power provided by a cable is converted to acoustic energy. The high intensity acoustic energy directed to the borehole wall and into the near wellbore region, redissolves or resuspends the material which is reducing the permeability of the formation and/or restricting flow in the wellbore.

Maki, Jr., Voldi E. (11904 Bell Ave., Austin, TX 78759-2415); Sharma, Mukul M. (Dept. of Petroleum Engr. Univ. of Texas, Austin, TX 78712)

1997-01-21T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Development of a geothermal acoustic borehole televiewer  

DOE Green Energy (OSTI)

Most geothermal wells are drilled in hard rock formations where fluid flow is through systems of open fractures. Productivity of these wells is usually determined by the extent of intersection of the wellbore with the fracture system. A need exists for fracture mapping methods and tools which can operate in a geothermal environment. In less hostile environments, the acoustic borehole televiewer has been shown to be a useful tool for determining location, orientation, and characterization of fractures as they intersect the borehole and for general wellbore and casing inspection. The development conducted at Sandia National Laboratories to adapt an acoustic borehole televiewer for operation in a geothermal environment is described. The modified instrument has been successfully tested at temperatures as high as 280/sup 0/C and pressures up to 5000 psi, and used successfully to map fractures and casing damage in geothermal wells.

Heard, F.E.; Bauman, T.J.

1983-08-01T23:59:59.000Z

42

Compact acoustic refrigerator  

DOE Patents (OSTI)

This invention is comprised of a compact acoustic refrigeration system that actively cools components, e.g., electrical circuits, in a borehole environment. An acoustic engine includes first thermodynamic elements for generating a standing acoustic wave in a selected medium. An acoustic refrigerator includes second thermodynamic elements located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements and a relatively hot temperature at a second end of the second thermodynamic elements. A resonator volume cooperates with the first and second thermodynamic elements to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements, first heat pipes transfer heat from the heat load to the second thermodynamic elements and second heat pipes transfer heat from first and second thermodynamic elements to the borehole environment.

Bennett, G.A.

1991-12-31T23:59:59.000Z

43

Compact acoustic refrigerator  

DOE Patents (OSTI)

A compact acoustic refrigeration system actively cools components, e.g., electrical circuits, in a borehole environment. An acoustic engine includes first thermodynamic elements for generating a standing acoustic wave in a selected medium. An acoustic refrigerator includes second thermodynamic elements located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements and a relatively hot temperature at a second end of the second thermodynamic elements. A resonator volume cooperates with the first and second thermodynamic elements to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements, first heat pipes transfer heat from the heat load to the second thermodynamic elements and second heat pipes transfer heat from first and second thermodynamic elements to the borehole environment. 18 figs.

Bennett, G.A.

1992-11-24T23:59:59.000Z

44

Atmospheric Acoustic Minisounder  

Science Conference Proceedings (OSTI)

An improved version of a monostatic acoustic minisounder for the investigation of the structure and dynamics of the lower boundary layer, operating at high frequencies and equipped with a specially designed micro-antenna and advanced electronic ...

D. N. Asimakopoulos; C. G. Helmis; G. J. Stephanou

1987-06-01T23:59:59.000Z

45

Compact acoustic refrigerator  

DOE Patents (OSTI)

A compact acoustic refrigeration system actively cools components, e.g., electrical circuits (22), in a borehole environment. An acoustic engine (12, 14) includes first thermodynamic elements (12) for generating a standing acoustic wave in a selected medium. An acoustic refrigerator (16, 26, 28) includes second thermodynamic elements (16) located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements (16) and a relatively hot temperature at a second end of the second thermodynamic elements (16). A resonator volume (18) cooperates with the first and second thermodynamic elements (12, 16) to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements (12, 16), first heat pipes (24, 26) transfer heat from the heat load (22) to the second thermodynamic elements (16) and second heat pipes (28, 32) transfer heat from first and second thermodynamic elements (12, 16) to the borehole environment.

Bennett, Gloria A. (Los Alamos, NM)

1992-01-01T23:59:59.000Z

46

Spacetime transformation acoustics  

E-Print Network (OSTI)

A recently proposed analogue transformation method has allowed the extension of transformation acoustics to general spacetime transformations. We analyze here in detail the differences between this new analogue transformation acoustics (ATA) method and the standard one (STA). We show explicitly that STA is not suitable for transformations that mix space and time. ATA takes as starting point the acoustic equation for the velocity potential, instead of that for the pressure as in STA. This velocity-potential equation by itself already allows for some transformations mixing space and time, but not all of them. We explicitly obtain the entire set of transformations that do not leave its form invariant. It is in these cases that ATA shows its true potential, allowing for building a transformation acoustics method that enables the full range of spacetime transformations. We provide an example of an important transformation which cannot be achieved with STA. Using this transformation, we design and simulate an acous...

García-Meca, C; Barceló, C; Jannes, G; Sánchez-Dehesa, J; Martínez, A

2013-01-01T23:59:59.000Z

47

Automatic acoustic guitar tuner  

E-Print Network (OSTI)

Acoustic guitar musicians tune their instruments by using a conventional tuner. Individuals pluck the string and the conventional tuner indicates whether the note is sharp or flat. The musician then has to wind the string ...

Bocanegra, Alfredo

2005-01-01T23:59:59.000Z

48

Acoustic imaging system  

DOE Patents (OSTI)

An acoustic imaging system for displaying an object viewed by a moving array of transducers as the array is pivoted about a fixed point within a given plane. A plurality of transducers are fixedly positioned and equally spaced within a laterally extending array and operatively directed to transmit and receive acoustic signals along substantially parallel transmission paths. The transducers are sequentially activated along the array to transmit and receive acoustic signals according to a preestablished sequence. Means are provided for generating output voltages for each reception of an acoustic signal, corresponding to the coordinate position of the object viewed as the array is pivoted. Receptions from each of the transducers are presented on the same display at coordinates corresponding to the actual position of the object viewed to form a plane view of the object scanned.

Smith, Richard W. (Richland, WA)

1979-01-01T23:59:59.000Z

49

Keyboard acoustic emanations revisited  

Science Conference Proceedings (OSTI)

We examine the problem of keyboard acoustic emanations. We present a novel attack taking as input a 10-minute sound recording of a user typing English text using a keyboard, and then recovering up to 96% of typed characters. There is no need for a labeled ... Keywords: HMM, acoustic emanations, cepstrum, computer security, electronic eavesdropping, hidden Markov models, human factors, keyboards, learning theory, privacy, signal analysis

Li Zhuang; Feng Zhou; J. D. Tygar

2005-11-01T23:59:59.000Z

50

Keyboard acoustic emanations revisited  

Science Conference Proceedings (OSTI)

We examine the problem of keyboard acoustic emanations. We present a novel attack taking as input a 10-minute sound recording of a user typing English text using a keyboard and recovering up to 96% of typed characters. There is no need for training ... Keywords: Computer security, HMM, acoustic manations, cepstrum, electronic eavesdropping, hidden markov models, human factors, keyboards, learning theory, privacy, signal analysis

Li Zhuang; Feng Zhou; J. D. Tygar

2009-10-01T23:59:59.000Z

51

Definition: Acoustic Televiewer | Open Energy Information  

Open Energy Info (EERE)

Televiewer Televiewer Jump to: navigation, search Dictionary.png Acoustic Televiewer The Acoustic Televiewer (ATV) log provides a very-high resolution, sonic image of the borehole wall. The tool consists of an ultrasonic transducer coupled with a downhole inclinometer. These devices are used to generate an oriented image of seismic velocity variation and wave amplitude. These images are then examined and highlighted to reveal fractures, bedding planes and orientation of those features. The log is useful for strata and fracture delineation, and can also be used to evaluate compressional-wave velocity, borehole deviation and eccentricity.[1] References ↑ http://www.dot.ca.gov/hq/esc/geotech/gg/atv_log.htm Ret LikeLike UnlikeLike You like this.Sign Up to see what your friends like.

52

Recovery Act  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 Recovery Act Buy American Requirements for Information Needed from Financial Assistance Applicants/Recipients for Waiver Requests Based on Unreasonable Cost or Nonavailability Applicants for and recipients of financial assistance funded by the Recovery Act must comply with the requirement that all of the iron, steel, and manufactured goods used for a project for the construction, alteration, maintenance, or repair of a public building or public work be produced in the United States, unless the head of the agency makes a waiver, or determination of inapplicability of the Buy American Recovery Act provisions, based on one of the authorized exceptions. The authorized exceptions are unreasonable cost, nonavailability, and in furtherance of the public interest. This

53

Acoustic Imaging Suite  

INL’s acoustic imaging technology improves methods of capturing moving images of a specified object by using a photorefractive effect to produce a full-field image of the object without using a probe to perform a full scan of the object. INL ...

54

Building Energy Software Tools Directory : Weather Tool  

NLE Websites -- All DOE Office Websites (Extended Search)

Weather Tool Back to Tool Screenshot for Weather Tool. Screenshot for Weather Tool. Screenshot for Weather...

55

Eventdriven, Rolebased Mobility in Disaster Recovery Networks  

E-Print Network (OSTI)

-1-59593-737-7/07/0009 ...$5.00. disaster response scenarios, understanding communication patterns in such networks is criticalEvent­driven, Role­based Mobility in Disaster Recovery Networks Samuel C. Nelson, Albert F. Harris important tools in understanding the com- plex characteristics of disaster recovery networks is simula- tion

Kravets, Robin

56

Cylindrical Acoustic Levitator/Concentrator  

NLE Websites -- All DOE Office Websites (Extended Search)

Cylindrical Acoustic Levitator/Concentrator Cylindrical Acoustic Levitator/Concentrator Cylindrical Acoustic Levitator/Concentrator A low-power, inexpensive acoustic apparatus for levitation and/or concentration of aerosols and small liquid/solid samples having particulates up to several millimeters in diameter in air or other fluids is described. Available for thumbnail of Feynman Center (505) 665-9090 Email Cylindrical Acoustic Levitator/Concentrator A low-power, inexpensive acoustic apparatus for levitation and/or concentration of aerosols and small liquid/solid samples having particulates up to several millimeters in diameter in air or other fluids is described. It is constructed from a commercially available, hollow cylindrical piezoelectric crystal which has been modified to tune the resonance frequency of the breathing mode resonance of the crystal to that

57

Acoustic Enhancement of Photodetecting Devices  

for suspect materials, to advanced weapons guidance. Using a high Q acoustic resonator, the invention increases the sensitivity of the detectors by an order of

58

Cylindrical Acoustic Levitator/Concentrator  

NLE Websites -- All DOE Office Websites (Extended Search)

A low-power, inexpensive acoustic apparatus for levitation andor concentration of aerosols and small liquidsolid samples having particulates up to several millimeters in...

59

Synergy of seismic, acoustic, and video signals in blast analysis  

SciTech Connect

The range of mining applications from hard rock quarrying to coal exposure to mineral recovery leads to a great variety of blasting practices. A common characteristic of many of the sources is that they are detonated at or near the earth`s surface and thus can be recorded by camera or video. Although the primary interest is in the seismic waveforms that these blasts generate, the visual observations of the blasts provide important constraints that can be applied to the physical interpretation of the seismic source function. In particular, high speed images can provide information on detonation times of individuals charges, the timing and amount of mass movement during the blasting process and, in some instances, evidence of wave propagation away from the source. All of these characteristics can be valuable in interpreting the equivalent seismic source function for a set of mine explosions and quantifying the relative importance of the different processes. This paper documents work done at the Los Alamos National Laboratory and Southern Methodist University to take standard Hi-8 video of mine blasts, recover digital images from them, and combine them with ground motion records for interpretation. The steps in the data acquisition, processing, display, and interpretation are outlined. The authors conclude that the combination of video with seismic and acoustic signals can be a powerful diagnostic tool for the study of blasting techniques and seismology. A low cost system for generating similar diagnostics using consumer-grade video camera and direct-to-disk video hardware is proposed. Application is to verification of the Comprehensive Test Ban Treaty.

Anderson, D.P. [Southern Methodist Univ., Dallas, TX (United States); Stump, B.W. [Los Alamos National Lab., NM (United States); Weigand, J. [Vibronics Inc. (United States)

1997-09-01T23:59:59.000Z

60

Acoustic Character Of Hydraulic Fractures In Granite  

E-Print Network (OSTI)

Hydraulic fractures in homogeneous granitic rocks were logged with conventional acoustic-transit-time, acoustic-waveform, and acoustic-televiewer logging systems. Fractured intervals ranged in depth from 45 to 570m. and ...

Paillet, Frederick I.

1983-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Recovery Newsletters  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

newsletters Office of Environmental newsletters Office of Environmental Management 1000 Independence Ave., SW Washington, DC 20585 202-586-7709 en 2011 ARRA Newsletters http://energy.gov/em/downloads/2011-arra-newsletters 2011 ARRA Newsletters

62

Prioritization Tool  

NLE Websites -- All DOE Office Websites (Extended Search)

2013 Building Technologies Office Prioritization Tool 2 | Building Technologies Office eere.energy.gov Vision: develop an analytical tool that considers building efficiency...

63

A broadband underwater acoustic modem implementation using coherent OFDM  

E-Print Network (OSTI)

Abstract — Multicarrier modulation in the form of orthogonal frequency division multiplexing (OFDM) has prevailed in recent broadband wireless systems over radio channels. In this senior design project, we have implemented an acoustic OFDM modem that transmits digital data through sound propagation. We have demonstrated OFDM transmission first in air, and then in water. We find that the underwater channel is much more complex than the air channel, and careful signal designs are needed for underwater transmissions. We have also handled another difficulty incurred by sampling rate mismatches at the transmitter and the receiver due to low-cost sampling devices. With two-way communication capabilities, this project provides a simple online chatting tool between two computers relying on acoustic links. Index Terms — OFDM, multicarrier transmission, underwater acoustic communication.

Sean Mason; Robert Anstett; Nicoletti Anicette; Shengli Zhou

2007-01-01T23:59:59.000Z

64

The electron geodesic acoustic mode  

Science Conference Proceedings (OSTI)

In this report, a novel new mode, named the electron geodesic acoustic mode, is presented. This mode can occur in toroidal plasmas like the conventional geodesic acoustic mode (GAM). The frequency of this new mode is much larger than that of the conventional GAM by a factor equal to the square root of the ion to electron mass ratio.

Chakrabarti, N. [Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Calcutta 700 064 (India); Guzdar, P. N. [Institute for Research in Electronics and Applied Physics, University of Maryland, College Park, Maryland 20742 (United States); Kaw, P. K. [Institute for Plasma Research Bhat, Gandhinagar 382428 (India)

2012-09-15T23:59:59.000Z

65

Acoustics sound systems for baseball  

Science Conference Proceedings (OSTI)

Acoustic considerations impact the design of sound systems for baseball stadiums in several important ways. Intrusion by the sound system into adjacent residential communities must often be minimized. Excess attenuation greatly increases the required high frequency component of acoustic power for sound travelling long distances

2001-01-01T23:59:59.000Z

66

NW-MILO Acoustic Data Collection  

SciTech Connect

There is an enduring requirement to improve our ability to detect potential threats and discriminate these from the legitimate commercial and recreational activity ongoing in the nearshore/littoral portion of the maritime domain. The Northwest Maritime Information and Littoral Operations (NW-MILO) Program at PNNL’s Coastal Security Institute in Sequim, Washington is establishing a methodology to detect and classify these threats - in part through developing a better understanding of acoustic signatures in a near-shore environment. The purpose of the acoustic data collection described here is to investigate the acoustic signatures of small vessels. The data is being recorded continuously, 24 hours a day, along with radar track data and imagery. The recording began in August 2008, and to date the data contains tens of thousands of signals from small vessels recorded in a variety of environmental conditions. The quantity and variety of this data collection, with the supporting imagery and radar track data, makes it particularly useful for the development of robust acoustic signature models and advanced algorithms for signal classification and information extraction. The underwater acoustic sensing system is part of a multi-modal sensing system that is operating near the mouth of Sequim Bay. Sequim Bay opens onto the Straight of Juan de Fuca, which contains part of the border between the U.S. and Canada. Table 1 lists the specific components used for the NW-MILO system. The acoustic sensor is a hydrophone permanently deployed at a mean depth of about 3 meters. In addition to a hydrophone, the other sensors in the system are a marine radar, an electro-optical (EO) camera and an infra-red (IR) camera. The radar is integrated with a vessel tracking system (VTS) that provides position, speed and heading information. The data from all the sensors is recorded and saved to a central server. The data has been validated in terms of its usability for characterizing the signatures of small vessels. The sampling rate of 8 kHz and low pass filtering to 2 kHz results in an alias-free signal in the frequency band that is appropriate for small vessels. Calibration was performed using a Lubell underwater speaker so that the raw data signal levels can be converted to sound pressure. Background noise is present due to a nearby pump and as a result of tidal currents. More study is needed to fully characterize the noise, but it does not pose an obstacle to using the acoustic data for the purposes of vessel detection and signature analysis. The detection range for a small vessel was estimated using the calibrated voltage response of the system and a cylindrical spreading model for transmission loss. The sound pressure of a typical vessel with an outboard motor was found to be around 140 dB mPa, and could theoretically be detected from 10 km away. In practical terms, a small vessel could reliably be detected from 3 - 5 km away. The data is archived in netCDF files, a standard scientific file format that is "self describing". This means that each data file contains the metadata - timestamps, units, origin, etc. - needed to make the data meaningful and portable. Other file formats, such as XML, are also supported. A visualization tool has been developed to view the acoustic data in the form of spectrograms, along with the coincident radar track data and camera images.

Matzner, Shari; Myers, Joshua R.; Maxwell, Adam R.; Jones, Mark E.

2010-02-17T23:59:59.000Z

67

Acoustic Logs At Newberry Caldera Area (Combs, Et Al., 1999) | Open Energy  

Open Energy Info (EERE)

Acoustic Logs At Newberry Caldera Area (Combs, Et Al., 1999) Acoustic Logs At Newberry Caldera Area (Combs, Et Al., 1999) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Newberry Caldera Area (Combs, Et Al., 1999) Exploration Activity Details Location Newberry Caldera Area Exploration Technique Acoustic Logs Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes The acoustic borehole televiewer (BHTV) was run twice in the wellbore with limited success. There were several problems with the tool's fimctions, but images were successfully obtained over the interval from 2748' to 3635'. References Jim Combs, John T. Finger, Colin Goranson, Charles E. Hockox Jr., Ronald D. Jacobsen, Gene Polik (1999) Slimhole Handbook- Procedures And Recommendations For Slimhole Drilling And Testing In Geothermal Exploration

68

Opto-acoustic thrombolysis  

DOE Patents (OSTI)

This invention is a catheter-based device for generating an ultrasound excitation in biological tissue. Pulsed laser light is guided through an optical fiber to provide the energy for producing the acoustic vibrations. The optical energy is deposited in a water-based absorbing fluid, e.g. saline, thrombolytic agent, blood or thrombus, and generates an acoustic impulse in the fluid through thermoelastic and/or thermodynamic mechanisms. By pulsing the laser at a repetition rate (which may vary from 10 Hz to 100 kHz) an ultrasonic radiation field can be established locally in the medium. This method of producing ultrasonic vibrations can be used in vivo for the treatment of stroke-related conditions in humans, particularly for dissolving thrombus or treating vasospasm. The catheter can also incorporate thrombolytic drug treatments as an adjunct therapy and it can be operated in conjunction with ultrasonic detection equipment for imaging and feedback control and with optical sensors for characterization of thrombus type and consistency.

Celliers, Peter (Berkeley, CA); Da Silva, Luiz (Danville, CA); Glinsky, Michael (Livermore, CA); London, Richard (Orinda, CA); Maitland, Duncan (Livermore, CA); Matthews, Dennis (Moss Beach, CA); Fitch, Pat (Livermore, CA)

2000-01-01T23:59:59.000Z

69

Opto-acoustic thrombolysis  

Science Conference Proceedings (OSTI)

This invention is a catheter-based device for generating an ultrasound excitation in biological tissue. Pulsed laser light is guided through an optical fiber to provide the energy for producing the acoustic vibrations. The optical energy is deposited in a water-based absorbing fluid, e.g. saline, thrombolytic agent, blood or thrombus, and generates an acoustic impulse in the fluid through thermoelastic and/or thermodynamic mechanisms. By pulsing the laser at a repetition rate (which may vary from 10 Hz to 100 kHz) an ultrasonic radiation field can be established locally in the medium. This method of producing ultrasonic vibrations can be used in vivo for the treatment of stroke-related conditions in humans, particularly for dissolving thrombus or treating vasospasm. The catheter can also incorporate thrombolytic drug treatments as an adjunct therapy and it can be operated in conjunction with ultrasonic detection equipment for imaging and feedback control and with optical sensors for characterization of thrombus type and consistency.

Celliers, P.; Silva, L. Da; Glinsky, M.; London, R.; Maitland, D.; Matthews, D.; Fitch, P.

2000-02-08T23:59:59.000Z

70

Building Energy Software Tools Directory: Tools Listed Alphabetically  

NLE Websites -- All DOE Office Websites (Extended Search)

level Acoustics Program HVAC acoustics, sound level prediction, noise level Acuity Energy Platform energy efficiency software; customized business recommendation; commercial...

71

Acoustic Inspection Devices: Detecting the Undetectable  

Acoustic Inspection Devices: Detecting the Undetectable Emerging homeland security threats and increasingly sophisticated adversaries have heightened ...

72

Acoustical heat-pumping engine  

DOE Patents (OSTI)

The disclosure is directed to an acoustical heat pumping engine without moving seals. A tubular housing holds a compressible fluid capable of supporting an acoustical standing wave. An acoustical driver is disposed at one end of the housing and the other end is capped. A second thermodynamic medium is disposed in the housing near to but spaced from the capped end. Heat is pumped along the second thermodynamic medium toward the capped end as a consequence both of the pressure oscillation due to the driver and imperfect thermal contact between the fluid and the second thermodynamic medium.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1981-08-14T23:59:59.000Z

73

Analysis & Tools: Tools and Tool Interaction AAU  

E-Print Network (OSTI)

During the three years of AMETIST the performance and usability of the existing tools for analysing timed automata models have improved enormously. In addition to traditional verification of timed models, emphasis has been put into retargeting the technology towards optimal scheduling and performance analysis and have been pursued in a number of new tools developed

unknown authors

2005-01-01T23:59:59.000Z

74

ARM - Recovery Act Instruments  

NLE Websites -- All DOE Office Websites (Extended Search)

ActRecovery Act Instruments ActRecovery Act Instruments Recovery Act Logo Subscribe FAQs Recovery Act Instruments Recovery Act Fact Sheet March 2010 Poster (PDF, 10MB) External Resources Recovery Act - Federal Recovery Act - DOE Recovery Act - ANL Recovery Act - BNL Recovery Act - LANL Recovery Act - PNNL Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Recovery Act Instruments These pages provide a breakdown of the new instruments planned for installation among the permanent and mobile ARM sites. In addition, several instruments will be purchased for use throughout the facility and deployed as needed. These are considered "facility spares" and are included in the table below. View All | Hide All ARM Aerial Facility Instrument Title Instrument Mentor Measurement Group Measurements

75

Building Energy Software Tools Directory: Tools by Subject - Other  

NLE Websites -- All DOE Office Websites (Extended Search)

Indoor Air Indoor Air A B C D E F I K L M P S T U V Tool Applications Free Recently Updated AcousticCalc HVAC acoustics, sound level prediction, noise level AnTherm Thermal heat bridges, heat flow, steady state, 2D, 3D, transfer coefficients, thermal conductance, visualization, simulation, European standards, EPBD, temperature distribution, vapor transfer, vapor diffusion, avoiding moisture, avoiding mould, energy performance, linear thermal transmittance, point thermal transmittance, vapor pressure, surface condensation, thermal comfort, dew point Software has been updated. BuildingAdvice Whole building analysis, energy simulation, renewable energy, retrofit analysis, sustainability/green buildings Software has been updated. BUS++ energy performance, ventilation, air flow, indoor air quality, noise level Software has been updated.

76

Building Energy Software Tools Directory: Tools by Subject - Whole Building  

NLE Websites -- All DOE Office Websites (Extended Search)

Retrofit Analysis Retrofit Analysis A B C D E F G H I L M N O P R S T U V W Tool Applications Free Recently Updated AcousticCalc HVAC acoustics, sound level prediction, noise level AEPS System Planning electrical system, renewable energy system, planning and design software, modeling, simulation, energy usage, system performance, financial analysis, solar, wind, hydro, behavior characteristics, usage profiles, generation load storage calculations, on-grid, off-grid, residential, commercial, system sizing, utility rate plans, rate comparison, utility costs, energy savings Software has been updated. AFT Fathom design, pump selection, pipe analysis, duct design, duct sizing, chilled water systems, hot water system Software has been updated. AUDIT operating cost, bin data, residential, commercial

77

Building Energy Software Tools Directory: Tools by Subject - Other  

NLE Websites -- All DOE Office Websites (Extended Search)

Multibuilding Facilities Multibuilding Facilities A B C E F G H I K L M N O P Q R T U V W Tool Applications Free Recently Updated AcousticCalc HVAC acoustics, sound level prediction, noise level Benchmata Automated Benchmarking System Automation Portfolio Manager Software has been updated. BuildingAdvice Whole building analysis, energy simulation, renewable energy, retrofit analysis, sustainability/green buildings Software has been updated. Carbon Estates Energy Benchmarking; Retrofitting Simulation; Energy Management; Carbon Management Software has been updated. Commodity Server energy database server, time series energy, portfolio management CONTAM airflow analysis; building controls; contaminant dispersal; indoor air quality, multizone analysis, smoke control, smoke management, ventilation Free software. Software has been updated.

78

Software Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Software Tools LBNL's WINDOW and THERM software tools are key to evaluating new design concepts RESFEN -- Version 5.0 now available A PC program for calculating the heating and...

79

Recovery Act Open House  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery Act Open House North Wind Environmental was one of three local small businesses that received Recovery Funding for projects at DOE's Idaho Site. Members of the community...

80

Tool Catalog  

Science Conference Proceedings (OSTI)

... Microscopy tool. File Utilities, Control file load order, JPEG compression, etc. Fourier, ... Fractal - Koch, Generate Koch curves.. Fractal ...

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Employing the complete acoustical palette in teleconferencing design  

Science Conference Proceedings (OSTI)

The prevailing architectural acoustics approach in teleconferencing is “Deader is better” or “No acoustics is better than bad acoustics.” In some situations

Peter D'Antonio

1989-01-01T23:59:59.000Z

82

Iterative equalization and decoding applied to underwater acoustic communication  

E-Print Network (OSTI)

1.1 Shallow Underwater Acoustic Channels . . . . . . . .and Decoding Approach for Underwater Acoustic Commu-Equalization and Decoding of Underwater Acoustic Using Array

Sifferlen, James F.

2008-01-01T23:59:59.000Z

83

Acoustic Backscatter from Turbulent Microstructure  

Science Conference Proceedings (OSTI)

Acoustic backscatter has produced spectacular images of internal ocean processes for nearly two decades, but interpretation of the images remains ambiguous because several mechanisms can generate measurable backscatter. The authors present what ...

Harvey E. Seim; Michael C. Gregg; R. T. Miyamoto

1995-04-01T23:59:59.000Z

84

Forest Products: Acoustic Humidity Sensor  

SciTech Connect

The new acoustic sensor, designed as a humidity-control system for the paper and textile industries, can both eliminate overdrying and improve product quality by measuring humidity precisely. This new fact sheet explains how the process works.

Poole, L.; Recca, L.

1999-01-29T23:59:59.000Z

85

Acoustically Enhanced Boiling Heat Transfer  

E-Print Network (OSTI)

An acoustic field is used to increase the critical heat flux (CHF) of a flat-boiling-heat-transfer surface. The increase is a result of the acoustic effects on the vapor bubbles. Experiments are performed to explore the effects of an acoustic field on vapor bubbles in the vicinity of a rigid-heated wall. Work includes the construction of a novel heater used to produce a single vapor bubble of a prescribed size and at a prescribed location on a flatboiling surface for better study of an individual vapor bubble's reaction to the acoustic field. Work also includes application of the results from the single-bubble heater to a calibrated-copper heater used for quantifying the improvements in CHF.

Z. W. Douglas; M. K. Smith; A. Glezer

2008-01-07T23:59:59.000Z

86

Acoustic Characterization of Mesoscale Objects  

SciTech Connect

This report describes the science and engineering performed to provide state-of-the-art acoustic capabilities for nondestructively characterizing mesoscale (millimeter-sized) objects--allowing micrometer resolution over the objects entire volume. Materials and structures used in mesoscale objects necessitate the use of (1) GHz acoustic frequencies and (2) non-contacting laser generation and detection of acoustic waves. This effort demonstrated that acoustic methods at gigahertz frequencies have the necessary penetration depth and spatial resolution to effectively detect density discontinuities, gaps, and delaminations. A prototype laser-based ultrasonic system was designed and built. The system uses a micro-chip laser for excitation of broadband ultrasonic waves with frequency components reaching 1.0 GHz, and a path-stabilized Michelson interferometer for detection. The proof-of-concept for mesoscale characterization is demonstrated by imaging a micro-fabricated etched pattern in a 70 {micro}m thick silicon wafer.

Chinn, D; Huber, R; Chambers, D; Cole, G; Balogun, O; Spicer, J; Murray, T

2007-03-13T23:59:59.000Z

87

Simulation tools  

E-Print Network (OSTI)

In the last two decades, simulation tools made a significant contribution to the great progress in development of power electronics. Time to market was shortened and development costs were reduced drastically. Falling costs, as well as improved speed and precision, opened new fields of application. Today, continuous and switched circuits can be mixed. A comfortable number of powerful simulation tools is available. The users have to choose the best suitable for their application. Here a simple rule applies: The best available simulation tool is the tool the user is already used to (provided, it can solve the task). Abilities, speed, user friendliness and other features are continuously being improved—even though they are already powerful and comfortable. This paper aims at giving the reader an insight into the simulation of power electronics. Starting with a short description of the fundamentals of a simulation tool as well as properties of tools, several tools are presented. Starting with simplified models ...

Jenni, F

2006-01-01T23:59:59.000Z

88

Building Energy Software Tools Directory: Tools by Country - Switzerland  

NLE Websites -- All DOE Office Websites (Extended Search)

Switzerland Switzerland A E F L M P U Tool Applications Free Recently Updated ACOUSALLE acoustics, codes and standards ECO-BAT environmental performance, life cycle assessment, sustainable development Software has been updated. EnerCAD Building Energy Efficiency; Early Design Optimization; Architecture Oriented; Life Cycle Analysis Software has been updated. flixo 2D heat transfer, cold bridge, fenestration, frame U-value, thermal bridge Software has been updated. LESO-COMFORT thermal comfort, load calculation, energy LESO-SHADE shading factors, solar shading, building geometry LESOCOOL airflow, passive cooling, energy simulation, mechanical ventilation LESODIAL Daylighting, early design stage, user-friendliness LESOKAI thermal tranmission, water vapor, building envelope Software has been updated.

89

Reference Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Reference Tools Current Greenhouse Gas Concentrations Name that compound: The numbers game for CFCs, HFCs, HCFCs, and Halons Conversion Tables and More Glossary Acronyms CDIAC's...

90

Percussion Tool  

INL has invented a new technology for use in an electric percussion hammer drill, which includes a reciprocal moveable hammer that drives a tool bit ...

91

Tools & Technologies  

Energy.gov (U.S. Department of Energy (DOE))

We provide leadership for transforming workforce development through the power of technology. It develops corporate educational technology policy and enables the use of learning tools and...

92

Analysis Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Genome Channel Generation GRAIL GRAILEXP Pipeline Domain Parser Prospect MIRA Analysis Tools We are the Computational Biology and Bioinformatics Group of the Biosciences Division...

93

CMVRTC: Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

tool that graphically displays weight and inspection stations for each state across a Google map. Visit the Nationwide Weight & Inspection Station site to view your data. google...

94

The Design of Acoustic Radar Baffles  

Science Conference Proceedings (OSTI)

Compact acoustic antenna arrays, commonly used for profiling urban atmospheres, usually require acoustic baffles to minimize reflections from hard objects and to limit the impact of the 2–6-kHz signals on inhabitants. To facilitate optimum ...

C. J. Werkhoven; S. G. Bradley

1997-06-01T23:59:59.000Z

95

Acoustic data transmission through a drill string  

DOE Patents (OSTI)

Acoustical signals are transmitted through a drill string by canceling upward moving acoustical noise and by preconditioning the data in recognition of the comb filter impedance characteristics of the drill string. 5 figs.

Drumheller, D.S.

1988-04-21T23:59:59.000Z

96

Acoustic Logs | Open Energy Information  

Open Energy Info (EERE)

Acoustic Logs Acoustic Logs Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Acoustic Logs Details Activities (7) Areas (6) Regions (0) NEPA(0) Exploration Technique Information Exploration Group: Downhole Techniques Exploration Sub Group: Well Log Techniques Parent Exploration Technique: Well Log Techniques Information Provided by Technique Lithology: determine porosity of layers Stratigraphic/Structural: map discontinuities to determine their orientation. Hydrological: Thermal: Cost Information Low-End Estimate (USD): 1.00100 centUSD 1.0e-3 kUSD 1.0e-6 MUSD 1.0e-9 TUSD / foot Median Estimate (USD): 4.62462 centUSD 0.00462 kUSD 4.62e-6 MUSD 4.62e-9 TUSD / foot High-End Estimate (USD): 16.001,600 centUSD 0.016 kUSD 1.6e-5 MUSD 1.6e-8 TUSD / foot

97

Particle analysis in an acoustic cytometer  

SciTech Connect

The present invention is a method and apparatus for acoustically manipulating one or more particles. Acoustically manipulated particles may be separated by size. The particles may be flowed in a flow stream and acoustic radiation pressure, which may be radial, may be applied to the flow stream. This application of acoustic radiation pressure may separate the particles. In one embodiment, the particles may be separated by size, and as a further example, the larger particles may be transported to a central axis.

Kaduchak, Gregory; Ward, Michael D

2012-09-18T23:59:59.000Z

98

Owens Corning Acoustic & Insulation Product Testing ...  

Science Conference Proceedings (OSTI)

... Insulation. [01/T10] ASTM C687 Thermal Resistance of Loose-Fill Building Insulation. Acoustical Testing Services. Accreditation ...

2014-01-03T23:59:59.000Z

99

Energy Recovery Council (ERC) Wast to Energy (WTE) | Open Energy  

Open Energy Info (EERE)

Energy Recovery Council (ERC) Wast to Energy (WTE) Energy Recovery Council (ERC) Wast to Energy (WTE) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Energy Recovery Council (ERC) Wast to Energy (WTE) Agency/Company /Organization: Energy Recovery Council (ERC) Sector: Energy Focus Area: Biomass, - Waste to Energy Phase: Create a Vision Resource Type: Dataset, Publications, Guide/manual User Interface: Website Website: www.wte.org/ Cost: Free The Energy Recovery Council is a national trade organization representing the waste-to-energy industry and communities that own waste-to-energy facilities. Overview The Energy Recovery Council is a national trade organization representing the waste-to-energy industry and communities that own waste-to-energy facilities. The website includes information on waste-to-energy basics

100

Acoustic Analysis of Adult Speaker Age  

Science Conference Proceedings (OSTI)

Information about the age of the speaker is always present in speech. It is used as perceptual cues to age by human listeners, and can be measured acoustically and used by automatic age estimators. This chapter offers an introduction to the phonetic ... Keywords: Acoustic analysis, Acoustic correlates, Phonetics, Speaker age

Susanne Schötz

2007-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Disaster Resiliency and Recovery: Capabilities (Fact Sheet)  

SciTech Connect

The National Renewable Energy Laboratory (NREL) is the nation's leader in energy efficient and renewable energy technologies, practices, and strategies. For the last 15 years, NREL has provided expertise, tools, and innovations to private industry; federal, state, and local governments; non-profit organizations; and communities during the planning, recovery, and rebuilding stages after disaster strikes.

Not Available

2012-11-01T23:59:59.000Z

102

Disaster Resiliency and Recovery: Capabilities (Fact Sheet)  

SciTech Connect

The National Renewable Energy Laboratory (NREL) is the nation's leader in energy efficient and renewable energy technologies, practices, and strategies. For the last 15 years, NREL has provided expertise, tools, and innovations to private industry; federal, state, and local governments; non-profit organizations; and communities during the planning, recovery, and rebuilding stages after disaster strikes.

2012-11-01T23:59:59.000Z

103

Environmental Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

The Office of Health, Safety and Security HSS Logo Department of Energy Seal Left Tab SEARCH Right Tab TOOLS Right Tab Left Tab HOME Right Tab Left Tab ABOUT US Right Tab Left Tab...

104

Prioritization Tool  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Program Peer Review Alexis Abramson Chief Scientist alexis.abramson@ee.doe.gov April 2, 2013 Building Technologies Office Prioritization Tool 2 | Building Technologies Office eere.energy.gov Vision: develop an analytical tool that considers building efficiency measures and technologies, and assesses and compares their potential value into the future Uses: * Inform programmatic decision-making * Examine "what if" scenarios * Create targets for FOAs

105

OE Recovery Act Blog | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery Recovery Act Blog OE Recovery Act Blog RSS September 20, 2013 Electrical transmission lines cross a snow-covered field in Dallas Dam, Oregon. | Energy Department photo. Top 9 Things You Didn't Know About America's Power Grid Ever wonder how electricity gets to your home? Test your knowledge with these top power grid facts. July 11, 2013 Demand Response: Lessons Learned with an Eye to the Future Under the Recovery Act, the Energy Department awarded $3.5 billion in funds to the electricity industry, including OG&E, to help catalyze the adoption of smart grid tools, technologies and techniques such as demand response that are designed to increase the electric grid's flexibility, reliability, efficiency, affordability, and resiliency. Understanding lessons learned from these projects is vital.

106

Acoustic black holes Matt Visser  

E-Print Network (OSTI)

Acoustic black holes Matt Visser Physics Department Washington University Saint Louis USA Ole Miss you develop a number of use- ful connections between supersonic uid ow and black holes in general is the basis underlying a deep and fruitful analogy between the black holes of Einstein gravity and supersonic

Visser, Matt

107

Acoustic-wave sensor apparatus for analyzing a petroleum-based composition and sensing solidification of constituents therein  

DOE Patents (OSTI)

An acoustic-wave sensor apparatus and method are disclosed. The apparatus for analyzing a normally liquid petroleum-based composition includes at least one acoustic-wave device in contact with the petroleum-based composition for sensing or detecting the presence of constituents (e.g. paraffins or petroleum waxes) therein which solidify upon cooling of the petroleum-based composition below a cloud-point temperature. The acoustic-wave device can be a thickness-shear-mode device (also termed a quartz crystal microbalance), a surface-acoustic-wave device, an acoustic-plate-mode device or a flexural plate-wave device. Embodiments of the present invention can be used for measuring a cloud point, a pour point and/or a freeze point of the petroleum-based composition, and for determining a temperature characteristic of each point. Furthermore, measurements with the acoustic-wave sensor apparatus can be made off-line by using a sample having a particular petroleum-based composition; or in-situ with the petroleum-based composition contained within a pipeline or storage tank. The acoustic-wave sensor apparatus has uses in many different petroleum technology areas, including the recovery, transport, storage, refining and use of petroleum and petroleum-based products. 7 figs.

Spates, J.J.; Martin, S.J.; Mansure, A.J.

1997-08-26T23:59:59.000Z

108

Mass and Heat Recovery  

E-Print Network (OSTI)

In the last few years heat recovery was under spot and in air conditioning fields usually we use heat recovery by different types of heat exchangers. The heat exchanging between the exhaust air from the building with the fresh air to the building (air to air heat exchanger). In my papers I use (water to air heat exchanger) as a heat recovery and I use the water as a mass recovery. The source of mass and heat recovery is the condensate water which we were dispose and connect it to the drain lines.

Hindawai, S. M.

2010-01-01T23:59:59.000Z

109

American Recovery and Reinvestment Act Information Services  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery and Reinvestment Act Recovery and Reinvestment Act Information Services American Recovery and Reinvestment Act American Recovery and Reinvestment Act Information Services American Recovery and Reinvestment Act American Recovery and Reinvestment Act Information Services American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act

110

Battleground Energy Recovery Project  

Science Conference Proceedings (OSTI)

In October 2009, the project partners began a 36-month effort to develop an innovative, commercial-scale demonstration project incorporating state-of-the-art waste heat recovery technology at Clean Harbors, Inc., a large hazardous waste incinerator site located in Deer Park, Texas. With financial support provided by the U.S. Department of Energy, the Battleground Energy Recovery Project was launched to advance waste heat recovery solutions into the hazardous waste incineration market, an area that has seen little adoption of heat recovery in the United States. The goal of the project was to accelerate the use of energy-efficient, waste heat recovery technology as an alternative means to produce steam for industrial processes. The project had three main engineering and business objectives: Prove Feasibility of Waste Heat Recovery Technology at a Hazardous Waste Incinerator Complex; Provide Low-cost Steam to a Major Polypropylene Plant Using Waste Heat; and ï?· Create a Showcase Waste Heat Recovery Demonstration Project.

Daniel Bullock

2011-12-31T23:59:59.000Z

111

Simulation Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Building simulation tool screen capture Building simulation tool screen capture Simulation Tools Researchers develop whole-building energy simulation software programs that allow architects and building engineers to design or retrofit buildings for maximum energy efficiency and occupant comfort. Programs developed by researchers include: the EnergyPlus whole building simulation program, the Modelica Buildings library for rapid prototyping and controls design, the Building Controls Virtual Test Bed for co-simulation and for model-based operation, and the GenOpt generic optimization program. Contacts Philip Haves PHaves@lbl.gov (510) 486-6512 Michael Wetter MWetter@lbl.gov (510) 486-6990 Links Simulation Research Group Batteries and Fuel Cells Buildings Energy Efficiency Applications Commercial Buildings

112

Regulatory Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Regulatory Tools Regulatory Tools Home CRA - 2004 Final Recertification Decision CRA Comments & Responses CCA - 1996 CRA CARDs & TSDs CCA CARDs & TSDs Regulatory Tools Title 40 CFR Part 191 Environmental Radiation Protection Standards for Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes. Title 40 CFR Part 194 Criteria for the Certification and Re-Certification of the Waste Isolation Pilot Plant's Compliance With the 40 CFR Part 191 Disposal Regulations. Part I Title 40 CFR Part 194 Criteria for the Certification and Recertification of the Waste Isolation Pilot Plant's Compliance With the Disposal Regulations; Alternative Provisions; Proposed Rule. Friday August 9, 2002. Part II Title 40 CFR Part 194 Criteria for the Certification and Recertification of the Waste Isolation Pilot Plant's Compliance With the Disposal Regulations: Certification Decision; Final Rule. May 18, 1998. Part III

113

Tools & Resources: Resource Directory  

NLE Websites -- All DOE Office Websites (Extended Search)

Resource Directory Resource Directory The guidance documents and reports below have been used by Better Buildings Neighborhood Program partners to build their programs and guide them to early successes. The tools and calculators can be used by homeowners, business owners, and program designers to help determine energy savings and other benefits associated with energy efficiency upgrades. Guidance Documents and Reports Background Program Evaluation Program Updates and Lessons Learned Program Design Marketing and Driving Demand Financing and Incentives Workforce Development Partnering with Utilities Technical Resources Tools and Calculators For Homes For Commercial Buildings Emissions and Equivalency Calculators Guidance Documents and Reports Background Recovery Through Retrofit Report

114

Building Energy Software Tools Directory: CPF Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Related Links CPF Tools CPF Tools logo CPF Tools is the market-leading software for solar installers connecting sales, system design and financing. Screen Shots Keywords...

115

Quantum entanglement for acoustic spintronics  

SciTech Connect

We consider the entanglement of spins for two electrons contributing to the acoustoelectric current driven by a surface acoustic wave (SAW) in two adjacent narrow channels by calculating their exchange energy (J). The channels belong to an acoustic nanocircuit which comprises a network of quasi-one-dimensional pinched-off channels serving as wires along which SAW quantum dots transport electrons. This is motivated by possible practical applications involving quantum information processing and quantum computers. We calculate J as a function of time as the electrons travel side-by-side in the adjacent channels and as a function of the distance between the centers of the channels. The leakage from the state in which the system is prepared, is calculated. The oscillations in the leakage indicate the probability for the electron system to make transitions between the ground and excited states, or for an electron to hop back and forth between channels.

Gumbs, Godfrey; Abranyos, Yonatan [Department of Physics and Astronomy, Hunter College of the City University of New York, 695 Park Avenue, New York, New York 10021 (United States)

2004-11-01T23:59:59.000Z

116

Acoustic horizons in nuclear fluids  

E-Print Network (OSTI)

We consider a hydrodynamic description of the spherically symmetric outward flow of nuclear matter, accommodating dispersion in it as a very weak effect. About the resulting stationary conditions in the flow, we apply an Eulerian scheme to derive a fully nonlinear equation of a time-dependent radial perturbation. In its linearized limit, with no dispersion, this equation implies the static acoustic horizon of an analogue gravity model. We, however, show that time-dependent nonlinear effects destabilize the static horizon. We also model the perturbation as a high-frequency travelling wave, and perform a {\\it WKB} analysis, in which the effect of weak dispersion is studied iteratively. We show that even arbitrarily small values of dispersion make the horizon fully opaque to any acoustic disturbance propagating against the bulk flow, with the amplitude and the energy flux of the radial perturbation undergoing a discontinuity at the horizon, and decaying exponentially just outside it.

Niladri Sarkar; Abhik Basu; Jayanta K. Bhattacharjee; Arnab K. Ray

2013-06-03T23:59:59.000Z

117

Cylindrical acoustic levitator/concentrator  

DOE Patents (OSTI)

A low-power, inexpensive acoustic apparatus for levitation and/or concentration of aerosols and small liquid/solid samples having particulates up to several millimeters in diameter in air or other fluids is described. It is constructed from a commercially available, hollow cylindrical piezoelectric crystal which has been modified to tune the resonance frequency of the breathing mode resonance of the crystal to that of the interior cavity of the cylinder. When the resonance frequency of the interior cylindrical cavity is matched to the breathing mode resonance of the cylindrical piezoelectric transducer, the acoustic efficiency for establishing a standing wave pattern in the cavity is high. The cylinder does not require accurate alignment of a resonant cavity. Water droplets having diameters greater than 1 mm have been levitated against the force of gravity using; less than 1 W of input electrical power. Concentration of aerosol particles in air is also demonstrated.

Kaduchak, Gregory (Los Alamos, NM); Sinha, Dipen N. (Los Alamos, NM)

2002-01-01T23:59:59.000Z

118

Solid Rocket Motor Acoustic Testing  

DOE Green Energy (OSTI)

Acoustic data are often required for the determination of launch and powered flight loads for rocket systems and payloads. Such data are usually acquired during test firings of the solid rocket motors. In the current work, these data were obtained for two tests at a remote test facility where we were visitors. This paper describes the data acquisition and the requirements for working at a remote site, interfacing with the test hosts.

Rogers, J.D.

1999-03-31T23:59:59.000Z

119

Building Energy Software Tools Directory : Solar Tool  

NLE Websites -- All DOE Office Websites (Extended Search)

Country Related Links Solar Tool Back to Tool Screenshot for Solar Tool. Screenshot for Solar Tool. Contacts | Web Site Policies | U.S. Department of Energy | USA.gov Content...

120

Tenth oil recovery conference  

SciTech Connect

The Tertiary Oil Recovery Project is sponsored by the State of Kansas to introduce Kansas producers to the economic potential of enhanced recovery methods for Kansas fields. Specific objectives include estimation of the state-wide tertiary oil resource, identification and evaluation of the most applicable processes, dissemination of technical information to producers, occasional collaboration on recovery projects, laboratory studies on Kansas applicable processes, and training of students and operators in tertiary oil recovery methods. Papers have been processed separately for inclusion on the data base.

Sleeper, R. (ed.)

1993-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Cyanidation Recovery Process  

Science Conference Proceedings (OSTI)

Heat Treatment of Black Dross for the Production of a Value Added Material ... Leaching Studies for Metals Recovery from Waste Printed Wiring Boards (PWBs).

122

Fish Passage: A New Tool to Investigate Fish Movement: JSATS  

SciTech Connect

A new system is being used to determine fish mortality issues related to hydroelectric facilities in the Pacific Northwest. Called the juvenile salmon acoustic telemetry system (JSATS), this tool allows researchers to better understand fish movement, behavior, and survival around dams and powerhouses.

McMichael, Geoffrey A.; Harnish, Ryan A.; Weiland, Mark A.; Deng, Zhiqun; Eppard, Matthew B.

2011-04-20T23:59:59.000Z

123

Alion Science and Technology / Riverbank Acoustical ...  

Science Conference Proceedings (OSTI)

... E2179 Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing ... 08/P61] AAMA 1801 Acoustical Rating of Windows, Doors and ...

2013-07-19T23:59:59.000Z

124

Wind Turbine Acoustic Noise A white paper  

E-Print Network (OSTI)

Wind Turbine Acoustic Noise A white paper Prepared by the Renewable Energy Research Laboratory...................................................................... 8 Sound from Wind Turbines .............................................................................................. 10 Sources of Wind Turbine Sound

Massachusetts at Amherst, University of

125

DEVELOPMENT OF A LONG WAVELENGTH ACOUSTIC ...  

Science Conference Proceedings (OSTI)

... are developing a long-wavelength acoustic flowmeter (LWAF) for accurate, economical measurements of exhaust flows from coal-burning power ...

126

Ricoh Company LTD. Acoustical Testing Laboratory  

Science Conference Proceedings (OSTI)

Acoustical Testing Laboratory. ... 143-8555 JAPAN Contact: Mr. Seiji Nakamura Phone: 81-046-292-3871 Fax: E-Mail: seiji.nakamura@nts.ricoh.co.jp ...

2013-11-08T23:59:59.000Z

127

THE EFFECT OF ACOUSTIC MODULATION ON SPRAY ...  

Science Conference Proceedings (OSTI)

... that at full load in liquid injection systems, extra energy or perturbation is ... The acoustic modulation is generated by a piezoelectric crystal driven by a ...

128

Time synchronization for underwater acoustic sensor networks.  

E-Print Network (OSTI)

??The unique properties of underwater acoustic communications, such as large and time-varying propagation, low and range dependent bandwidth, and adverse operating environment make the synchronization… (more)

Khandoker, Tarik-Ul Islam

2012-01-01T23:59:59.000Z

129

Acoustic concentration of particles in fluid flow  

DOE Patents (OSTI)

An apparatus for acoustic concentration of particles in a fluid flow includes a substantially acoustically transparent membrane and a vibration generator that define a fluid flow path therebetween. The fluid flow path is in fluid communication with a fluid source and a fluid outlet and the vibration generator is disposed adjacent the fluid flow path and is capable of producing an acoustic field in the fluid flow path. The acoustic field produces at least one pressure minima in the fluid flow path at a predetermined location within the fluid flow path and forces predetermined particles in the fluid flow path to the at least one pressure minima.

Ward, Michael D. (Los Alamos, NM); Kaduchak, Gregory (Los Alamos, NM)

2010-11-23T23:59:59.000Z

130

Recovery Act State Summaries | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act State Summaries Recovery Act State Summaries Recovery Act State Summaries Alabama Recovery Act State Memo Alaska Recovery Act State Memo American Samoa Recovery Act State Memo Arizona Recovery Act State Memo Arkansas Recovery Act State Memo California Recovery Act State Memo Colorado Recovery Act State Memo Connecticut Recovery Act State Memo Delaware Recovery Act State Memo District of Columbia Recovery Act State Memo Florida Recovery Act State Memo Georgia Recovery Act State Memo Guam Recovery Act State Memo Hawaii Recovery Act State Memo Idaho Recovery Act State Memo Illinois Recovery Act State Memo Indiana Recovery Act State Memo Iowa Recovery Act State Memo Kansas Recovery Act State Memo Kentucky Recovery Act State Memo Louisiana Recovery Act State Memo Maine Recovery Act State Memo

131

Optimal adaptive sampling for continental shelf acoustic forecasting.  

Science Conference Proceedings (OSTI)

Shallow water acoustic propagation variability is driven by bathymetry and geo?acoustic and oceanographic variabilities. At the shelf?break

Kevin D. Heaney

2009-01-01T23:59:59.000Z

132

Reliable Data Communication and Storage in Underwater Acoustic Networks.  

E-Print Network (OSTI)

??Underwater acoustic communications (UAC) and networking (UAN) are promising paradigms for various oceanic applications. However, acoustic signal transmissions are characterized by long propagation delay, frequency-dependent… (more)

Cao, Rui

2011-01-01T23:59:59.000Z

133

Recovery Act Recipient Reporting  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Smart Grid Investment Grant Recipients Smart Grid Investment Grant Recipients November 19, 2009 1 Outline of Presentation * OMB Reporting Requirements * Jobs Guidance * FR.gov 2 Section 1512 of American Reinvestment and Recovery Act Outlines Recipient Reporting Requirements "Recipient reports required by Section 1512 of the Recovery Act will answer important questions, such as: â–ª Who is receiving Recovery Act dollars and in what amounts? â–ª What projects or activities are being funded with Recovery Act dollars? â–ª What is the completion status of such projects or activities and what impact have they had on job creation and retention?" "When published on www.Recovery.gov, these reports will provide the public with an unprecedented level of transparency into how Federal dollars are being spent and will help drive accountability for the timely,

134

Summary - Caustic Recovery Technology  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Caustic Recovery Technology Caustic Recovery Technology ETR Report Date: July 2007 ETR-7 United States Department of Energy Office of Environmental Management (DOE-EM) External Technical Review of Caustic Recovery Technology Why DOE-EM Did This Review The Department of Energy (DOE) Environmental Management Office (EM-21) has been developing caustic recovery technology for application to the Hanford Waste Treatment Plant (WTP) to reduce the amount of Low Activity Waste (LAW) vitrified. Recycle of sodium hydroxide with an efficient caustic recovery process could reduce the amount of waste glass produced by greater than 30%. The Ceramatec Sodium (Na), Super fast Ionic CONductors (NaSICON) membrane has shown promise for directly producing 50% caustic with high sodium selectivity. The external review

135

Acoustic Logs At Steamboat Springs Area (Combs, Et Al., 1999) | Open Energy  

Open Energy Info (EERE)

Steamboat Springs Area (Combs, Et Al., 1999) Steamboat Springs Area (Combs, Et Al., 1999) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Steamboat Springs Area (Combs, Et Al., 1999) Exploration Activity Details Location Steamboat Springs Area Exploration Technique Acoustic Logs Activity Date Usefulness useful DOE-funding Unknown Notes Two other Sandia instruments were used briefly: the acoustic borehole televiewer (BHTV) yielded wellbore images down to 520';and a Sandia memory tool gave pressuretemperature data for a shut-in test at the end of the project. Because no oriented core has been collected in this field, the televiewer images giving fracture direction were extremely M.ormative, but the BHTV could not be used at greater depths because of its temperature

136

Tool Steels  

Science Conference Proceedings (OSTI)

Table 6   Examples of ion implantation in metalforming and cutting applications...tool steel Machining 4140 N 80 3� life Taps HSS Tapping 4140 N 80 3� life HSS Tapping 4130 N 80 5� life HSS Tapping 4140 N 50 10� life M35 Tapping � N 2 200 4� life M7 Tapping � N 100 2� life Cutting blade M2 Cutting 1050 N 100 2� life M2 Cutting SAE 950 N 100 4� life Dies D2 Forming 321 SS N 80...

137

Remote Inspection Device - Heat Recovery Steam Generators  

Science Conference Proceedings (OSTI)

As heat recovery steam generators (HRSGs) have become more complex over the last 15 years, operating with multiple pressures and temperatures, operators have experienced more types of HRSG tube failures (HTFs). This report provides information on how nondestructive evaluation (NDE) can be combined with newly developed HRSG repair tooling so that operators can detect damaged tubes and verify that repaired tubes do not contain welding defects that might be detrimental to the life of the component.

2009-03-25T23:59:59.000Z

138

Acoustically enhanced heat exchange and drying apparatus  

DOE Patents (OSTI)

A heat transfer drying apparatus includes an acoustically augmented heat transfer chamber for receiving material to be dried. The chamber includes a first heat transfer gas inlet, a second heat transfer gas inlet, a material inlet, and a gas outlet which also serves as a dried material and gas outlet. A non-pulsing first heat transfer gas source provides a first drying gas to the acoustically augmented heat transfer chamber through the first heat transfer gas inlet. A valveless, continuous second heat transfer gas source provides a second drying gas to the acoustically augmented heat transfer chamber through the second heat transfer gas inlet. The second drying gas also generates acoustic waves which bring about acoustical coupling with the gases in the acoustically augmented heat transfer chamber. The second drying gas itself oscillates at an acoustic frequency of approximately 180 Hz due to fluid mechanical motion in the gas. The oscillations of the second heat transfer gas coupled to the first heat transfer gas in the acoustically augmented heat transfer chamber enhance heat and mass transfer by convection within the chamber. 3 figs.

Bramlette, T.T.; Keller, J.O.

1987-07-10T23:59:59.000Z

139

ACOUSTICAL IMAGING AND MECHANICAL PROPERTIES OF SOFT ROCK AND MARINE SEDIMENTS  

SciTech Connect

The research during this project has concentrated on developing a correlation between rock deformation mechanisms and their acoustic velocity signature. This has included investigating: (1) the acoustic signature of drained and undrained unconsolidated sands, (2) the acoustic emission signature of deforming high porosity rocks (in comparison to their low porosity high strength counterparts), (3) the effects of deformation on anisotropic elastic and poroelastic moduli, and (4) the acoustic tomographic imaging of damage development in rocks. Each of these four areas involve triaxial experimental testing of weak porous rocks or unconsolidated sand and involves measuring acoustic properties. The research is directed at determining the seismic velocity signature of damaged rocks so that 3-D or 4-D seismic imaging can be utilized to image rock damage. These four areas of study are described in the report: (1) Triaxial compression experiments have been conducted on unconsolidated Oil Creek sand at high confining pressures. (2) Initial experiments on measuring the acoustic emission activity from deforming high porosity Danian chalk were accomplished and these indicate that the AE activity was of a very low amplitude. (3) A series of triaxial compression experiments were conducted to investigate the effects of induced stress on the anisotropy developed in dynamic elastic and poroelastic parameters in rocks. (4) Tomographic acoustic imaging was utilized to image the internal damage in a deforming porous limestone sample. Results indicate that the deformation damage in rocks induced during laboratory experimentation can be imaged tomographically in the laboratory. By extension the results also indicate that 4-D seismic imaging of a reservoir may become a powerful tool for imaging reservoir deformation (including imaging compaction and subsidence) and for imaging zones where drilling operation may encounter hazardous shallow water flows.

Thurman E. Scott, Jr.; Younane Abousleiman

2004-04-01T23:59:59.000Z

140

Three-Dimensional Nonlinear Acoustical Holography  

E-Print Network (OSTI)

Nearfield Acoustical Holography (NAH) is an acoustic field visualization technique that can be used to reconstruct three-dimensional (3-D) acoustic fields by projecting two-dimensional (2-D) data measured on a hologram surface. However, linear NAH algorithms developed and improved by many researchers can result in significant reconstruction errors when they are applied to reconstruct 3-D acoustic fields that are radiated from a high-level noise source and include significant nonlinear components. Here, planar, nonlinear acoustical holography procedures are developed that can be used to reconstruct 3-D, nonlinear acoustic fields radiated from a high-level noise source based on 2-D acoustic pressure data measured on a hologram surface. The first nonlinear acoustic holography procedure is derived for reconstructing steady-state acoustic pressure fields by applying perturbation and renormalization methods to nonlinear, dissipative, pressure-based Westervelt Wave Equation (WWE). The nonlinear acoustic pressure fields radiated from a high-level pulsating sphere and an infinite-size, vibrating panel are used to validate this procedure. Although the WWE-based algorithm is successfully validated by those two numerical simulations, it still has several limitations: (1) Only the fundamental frequency and its second harmonic nonlinear components can be reconstructed; (2) the application of this algorithm is limited to mono-frequency source cases; (3) the effects of bent wave rays caused by transverse particle velocities are not included; (4) only acoustic pressure fields can be reconstructed. In order to address the limitations of the steady-state, WWE-based procedure, a transient, planar, nonlinear acoustic holography algorithm is developed that can be used to reconstruct 3-D nonlinear acoustic pressure and particle velocity fields. This procedure is based on Kuznetsov Wave Equation (KWE) that is directly solved by using temporal and spatial Fourier Transforms. When compared to the WWE-based procedure, the KWE-based procedure can be applied to multi-frequency source cases where each frequency component can contain both linear and nonlinear components. The effects of nonlinear bent wave rays can be also considered by using this algorithm. The KWE-based procedure is validated by conducting an experiment with a compression driver and four numerical simulations. The numerical and experimental results show that holographically-projected acoustic fields match well with directly-calculated and directly-measured fields.

Niu, Yaying

2013-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Heat Recovery Steam Generator Simulation  

E-Print Network (OSTI)

The paper discusses the applications of Heat Recovery Steam Generator Simulation. Consultants, plant engineers and plant developers can evaluate the steam side performance of HRSGs and arrive at the optimum system which matches the needs of the process plant, cogeneration or combined cycle plant. There is no need to design the HRSG per se and hence simulation is a valuable tool for anyone interested in evaluating the HRSG performance even before it is designed. It can also save a lot of time for specification writers as they need not guess how the steam side performance will vary with different gas/steam parameters. A few examples are given to show how simulation methods can be applied to real life problems.

Ganapathy, V.

1993-03-01T23:59:59.000Z

142

Comparative Performance of Acoustic-tagged and PIT-tagged Juvenile Salmonids  

DOE Green Energy (OSTI)

Numerous research tools and technologies are currently being used to evaluate fish passage and survival to determine the impacts of the Federal Columbia River Power System (FCRPS) on endangered and threatened juvenile salmonids, including PIT tags, balloon tags, hydroacoustic evaluations, radio telemetry, and acoustic telemetry. Each has advantages and disadvantages, but options are restricted in some situations because of limited capabilities of a specific technology, lack of detection capability downstream, or availability of adequate numbers of fish. However, there remains concern about the comparative effects of the tag or the tagging procedure on fish performance. The recently developed Juvenile Salmonid Acoustic Telemetry System (JSATS) acoustic transmitter is the smallest active acoustic tag currently available. The goal of this study was to determine whether fish tagged with the JSATS acoustic-telemetry tag can provide unbiased estimates of passage behavior and survival within the performance life of the tag. We conducted both field and laboratory studies to assess tag effects. For the field evaluation we released a total of 996 acoustic-tagged fish in conjunction with 21,026 PIT-tagged fish into the tailrace of Lower Granite Dam on 6 and 13 May. Travel times between release and downstream dams were not significantly different for the majority of the reaches between acoustic-tagged and PIT-tagged fish. In addition to the field evaluation, a series of laboratory experiments were conducted to determine if growth and survival of juvenile Chinook salmon surgically implanted with acoustic transmitters is different than untagged or PIT tagged juvenile Chinook salmon. Only yearling fish with integrated and non-integrated transmitters experienced mortalities, and these were low (<4.5%). Mortality among sub-yearling control and PIT-tag treatments ranged up to 7.7% while integrated and non-integrated treatments had slightly higher rates (up to 8.3% and 7.9% respectively). No acoustic transmitters were shed by yearling fish during the course of the 90 day study. Up to 7.8% of subyearling fish expelled transmitters. Tags were expelled from 5 to 63 days post-surgery. The average time to expulsion was 27 days; few fish expelled transmitters within 14 days of implantation or less. Histological results suggest that inflammation associated with implantation of an acoustic transmitter can produce fibrous tissue which can invade and possibly damage internal organs soon after implantation. Reactions severe enough to damage organs however, were limited to only ~20% of subyearling Chinook salmon, all of which were under 101mm and 12g at tagging. The infiltration of the fibrous tissue into organs was observed most often in fish held for 21 days and appeared to decrease in subsequent holding times.

Hockersmith, Eric E.; Brown, Richard S.; Liedtke, Theresa L.

2008-02-01T23:59:59.000Z

143

Comparative Performance of Acoustic-tagged and PIT-tagged Juvenile Salmonids  

Science Conference Proceedings (OSTI)

Numerous research tools and technologies are currently being used to evaluate fish passage and survival to determine the impacts of the Federal Columbia River Power System (FCRPS) on endangered and threatened juvenile salmonids, including PIT tags, balloon tags, hydroacoustic evaluations, radio telemetry, and acoustic telemetry. Each has advantages and disadvantages, but options are restricted in some situations because of limited capabilities of a specific technology, lack of detection capability downstream, or availability of adequate numbers of fish. However, there remains concern about the comparative effects of the tag or the tagging procedure on fish performance. The recently developed Juvenile Salmonid Acoustic Telemetry System (JSATS) acoustic transmitter is the smallest active acoustic tag currently available. The goal of this study was to determine whether fish tagged with the JSATS acoustic-telemetry tag can provide unbiased estimates of passage behavior and survival within the performance life of the tag. We conducted both field and laboratory studies to assess tag effects. For the field evaluation we released a total of 996 acoustic-tagged fish in conjunction with 21,026 PIT-tagged fish into the tailrace of Lower Granite Dam on 6 and 13 May. Travel times between release and downstream dams were not significantly different for the majority of the reaches between acoustic-tagged and PIT-tagged fish. In addition to the field evaluation, a series of laboratory experiments were conducted to determine if growth and survival of juvenile Chinook salmon surgically implanted with acoustic transmitters is different than untagged or PIT tagged juvenile Chinook salmon. Only yearling fish with integrated and non-integrated transmitters experienced mortalities, and these were low (tag treatments ranged up to 7.7% while integrated and non-integrated treatments had slightly higher rates (up to 8.3% and 7.9% respectively). No acoustic transmitters were shed by yearling fish during the course of the 90 day study. Up to 7.8% of subyearling fish expelled transmitters. Tags were expelled from 5 to 63 days post-surgery. The average time to expulsion was 27 days; few fish expelled transmitters within 14 days of implantation or less. Histological results suggest that inflammation associated with implantation of an acoustic transmitter can produce fibrous tissue which can invade and possibly damage internal organs soon after implantation. Reactions severe enough to damage organs however, were limited to only ~20% of subyearling Chinook salmon, all of which were under 101mm and 12g at tagging. The infiltration of the fibrous tissue into organs was observed most often in fish held for 21 days and appeared to decrease in subsequent holding times.

Hockersmith, Eric E.; Brown, Richard S.; Liedtke, Theresa L.

2008-02-01T23:59:59.000Z

144

Piezoelectric materials used in underwater acoustic transducers  

Science Conference Proceedings (OSTI)

Piezoelectric materials have been used in underwater acoustic transducers for nearly a century. In this paper, we reviewed four different types of piezoelectric materials: piezoelectric ceramics, single crystals, composites, and polymers, which are widely used in underwater acoustic transducers nowadays. Piezoelectric ceramics are the most dominant material type and are used as a single-phase material or one of the end members in composites. Piezoelectric single crystals offer outstanding electromechanical response but are limited by their manufacturing cost. Piezoelectric polymers provide excellent acoustic impedance matching and transducer fabrication flexibility although their piezoelectric properties are not as good as ceramics and single crystals. Composites combined the merits of ceramics and polymers and are receiving increased attention. The typical structure and electromechanical properties of each type of materials are introduced and discussed with respect to underwater acoustic transducer applications. Their advantages and disadvantages are summarized. Some of the critical design considerations when developing underwater acoustic transducers with these materials are also touched upon.

Li, Huidong; Deng, Zhiqun; Carlson, Thomas J.

2012-07-07T23:59:59.000Z

145

Enhanced recovery update  

SciTech Connect

Three key projects featuring enhanced operations in California are described. In the Kern River oil field, steaming at a pilot project is testing the hot plate heavy oil recovery method. In Buena Vista oil field, steam will be injected in a test project to determine the commercial feasibility of using steam for the enhanced recovery of light crude oil. Also, in the McKittrick oil field, 2 processes are being considered for a commercial heavy oil mining venture. Steam continues to be the most important element in the recovery of hard-to-produce oil. Other steam-using projects are highlighted.

Rintoul, B.

1984-02-01T23:59:59.000Z

146

Software Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Software Tools WINDOW for analyzing window thermal and optical performance THERM for analyzing two-dimensional heat transfer through building products Optics for analyzing optical properties of glazing systems International Glazing Database Optical data for glazing products used by WINDOW 5.2 and Optics5.1 including NFRC approved products Complex Glazing Database A database of shading materials and systems, such as roller shades and venetian blinds, that can be used by WINDOW 6 to calculate thermal and optical characteristics of window products with these shading systems. COMFEN A PC Program for calculating the heating and cooling energy use, and visual and thermal comfort, of commercial building facades. RESFEN A PC program for calculating the heating and cooling energy use of windows in residential buildings

147

Indispensable tool  

SciTech Connect

Synchrotron radiation has become an indispensable research tool for a growing number of scientists in a seemingly ever expanding number of disciplines. We can thank the European Synchrotron Research Facility (ESRF) in Grenoble for taking an innovative step toward achieving the educational goal of explaining the nature and benefits of synchrotron radiation to audiences ranging from the general public (including students) to government officials to scientists who may be unfamiliar with x-ray techniques and synchrotron radiation. ESRF is the driving force behind a new CD-ROM playable on both PCs and Macs titled Synchrotron light to explore matter. Published by Springer-Verlag, the CD contains both English and French versions of a comprehensive overview of the subject.

Robinson, Arthur

2001-08-10T23:59:59.000Z

148

Instrumentation Tools  

E-Print Network (OSTI)

Execution) is a tracing system developed by Larus and Ball which is incorporated as part of the Gnu C compiler [3]. Its goal is to generate very small traces which can be saved and then reused for multiple simulation runs. The modified compiler actually produces two executable programs. The first is the modified application. In addition to normal compilation, the compiler uses the notion of abstract execution to insert tracing code in the application code. Abstract execution is based upon control-flow tracing to reduce the amount of trace code necessary. The resulting trace produced by the modified application is only a tiny part of the full trace. This allows traces representing long execution runs to be saved on disk. The compiler also produces an application specific trace regeneration program. The regeneration program is a post-processing tool which accepts the compacted trace and outputs the full execution trace. The tracing overhead, including the cost of saving the compacted tra...

Jim Pierce; Michael D. Smith; Trevor Mudge

1995-01-01T23:59:59.000Z

149

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

Science Conference Proceedings (OSTI)

This technical progress report describes work performed from April 1 through June 30, 2002, for the project ''Heavy and Thermal Oil Recovery Production Mechanisms.'' We investigate a broad spectrum of topics related to thermal and heavy-oil recovery. Significant results were obtained in the areas of multiphase flow and rock properties, hot-fluid injection, improved primary heavy oil recovery, and reservoir definition. The research tools and techniques used are varied and span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history-matching techniques. Briefly, experiments were conducted to image at the pore level matrix-to-fracture production of oil from a fractured porous medium. This project is ongoing. A simulation studied was completed in the area of recovery processes during steam injection into fractured porous media. We continued to study experimentally heavy-oil production mechanisms from relatively low permeability rocks under conditions of high pressure and high temperature. High temperature significantly increased oil recovery rate and decreased residual oil saturation. Also in the area of imaging production processes in laboratory-scale cores, we use CT to study the process of gas-phase formation during solution gas drive in viscous oils. Results from recent experiments are reported here. Finally, a project was completed that uses the producing water-oil ratio to define reservoir heterogeneity and integrate production history into a reservoir model using streamline properties.

Anthony R. Kovscek

2002-07-01T23:59:59.000Z

150

American Recovery and Reinvestment Act  

Energy.gov (U.S. Department of Energy (DOE))

Here is one compliance agreement for EM’s American Recovery and Reinvestment Act Program on accelerated milestones for the Recovery Act program.

151

Recovery News Flashes  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

news-flashes Office of Environmental news-flashes Office of Environmental Management 1000 Independence Ave., SW Washington, DC 20585 202-586-7709 en "TRU" Success: SRS Recovery Act Prepares to Complete Shipment of More Than 5,000 Cubic Meters of Nuclear Waste to WIPP http://energy.gov/em/downloads/tru-success-srs-recovery-act-prepares-complete-shipment-more-5000-cubic-meters-nuclear recovery-act-prepares-complete-shipment-more-5000-cubic-meters-nuclear" class="title-link">"TRU" Success: SRS Recovery Act Prepares to Complete Shipment of More Than 5,000 Cubic Meters of Nuclear Waste to WIPP

152

Building Energy Software Tools Directory: Solar Tool  

NLE Websites -- All DOE Office Websites (Extended Search)

Building Energy Software Tools Directory EERE Building Technologies Office Building Energy Software Tools Directory Printable Version Share this resource Home About the...

153

Stone Tool Production  

E-Print Network (OSTI)

by the author. ) Stone Tool Production, Hikade, UEE 2010Short Citation: Hikade 2010, Stone Tool Production. UEE.Thomas, 2010, Stone Tool Production. In Willeke Wendrich (

Hikade, Thomas

2010-01-01T23:59:59.000Z

154

Multimodal Information Group- Tools  

Science Conference Proceedings (OSTI)

... Architecture and Tools for Linguistic Analysis Systems. Miscellaneous Tools. Name, Description. ... JobRunner is a tool designed to run a job (ie to ...

2013-07-12T23:59:59.000Z

155

Sparse Multichannel Estimation Algorithm for Cooperative Underwater Acoustic Communication Networks  

E-Print Network (OSTI)

Introduction: Cooperative Underwater Acoustic Communicationsgain for wireless and underwater network in interference-

Richard, Nick; Mitra, Urbasi

2007-01-01T23:59:59.000Z

156

Near-Real-Time Acoustic Monitoring of Beaked Whales and Other Cetaceans Using a SeagliderTM  

E-Print Network (OSTI)

­ a glider ­ equipped with an acoustic sensor and onboard data processing capabilities to passively scan Collective, Olympia, Washington, United States of America Abstract In most areas, estimating the presence for new, cost- effective tools that allow scientists to monitor areas of interest autonomously with high

Baird, Robin W.

157

Speaker verification system using acoustic data and non-acoustic data  

DOE Patents (OSTI)

A method and system for speech characterization. One embodiment includes a method for speaker verification which includes collecting data from a speaker, wherein the data comprises acoustic data and non-acoustic data. The data is used to generate a template that includes a first set of "template" parameters. The method further includes receiving a real-time identity claim from a claimant, and using acoustic data and non-acoustic data from the identity claim to generate a second set of parameters. The method further includes comparing the first set of parameters to the set of parameters to determine whether the claimant is the speaker. The first set of parameters and the second set of parameters include at least one purely non-acoustic parameter, including a non-acoustic glottal shape parameter derived from averaging multiple glottal cycle waveforms.

Gable, Todd J. (Walnut Creek, CA); Ng, Lawrence C. (Danville, CA); Holzrichter, John F. (Berkeley, CA); Burnett, Greg C. (Livermore, CA)

2006-03-21T23:59:59.000Z

158

Acoustically enhanced heat exchange and drying apparatus  

DOE Patents (OSTI)

A heat transfer apparatus includes a first chamber having a first heat transfer gas inlet, a second heat transfer gas inlet, and an outlet. A first heat transfer gas source provides a first gas flow to the first chamber through the first heat transfer gas inlet. A second gas flow through a second chamber connected to the side of the first chamber, generates acoustic waves which bring about acoustical coupling of the first and second gases in the acoustically augmented first chamber. The first chamber may also include a material inlet for receiving material to be dried, in which case the gas outlet serves as a dried material and gas outlet.

Bramlette, T. Tazwell (Livermore, CA); Keller, Jay O. (Oakland, CA)

1989-01-01T23:59:59.000Z

159

Copper vapor laser acoustic thermometry system  

DOE Patents (OSTI)

A copper vapor laser (CVL) acoustic thermometry system is disclosed. The invention couples an acoustic pulse a predetermined distance into a laser tube by means of a transducer and an alumina rod such that an echo pulse is returned along the alumina rod to the point of entry. The time differential between the point of entry of the acoustic pulse into the laser tube and the exit of the echo pulse is related to the temperature at the predetermined distance within the laser tube. This information is processed and can provide an accurate indication of the average temperature within the laser tube.

Galkowski, J.J.

1986-08-27T23:59:59.000Z

160

Particle collection enhancement by acoustics  

SciTech Connect

The overall objective of this project is to demonstrate pulse combustion induced acoustic enhancement of coal ash agglomeration and sulfur capture efficiency at conditions typical of proposed direct coal-fired turbines. The MTCI proprietary approach results in agglomerates that allow the use of conventional cyclones to achieve very high particulate collection efficiency and eliminates the need for barrier filters which pose concerns regarding durability and economics. The goal of the program is to support the mission of the Department of Energy (DOE) for developing coal-fired combustion gas turbines. The MTCI concept can be packaged either as a hot flue gas clean-up subsystem for the existing combustor island configurations or as an alterative primary pulse combustor island with integrated sulfur capture, particulate agglomeration and capture, alkali gettering and NO{sub x} emissions control.

Mansour, M.N.; Chandran, R.R.; Duqum, J.N. [Manufacturing and Technology Conversion International, Inc., Columbia, MD (United States); Scaroni, A.W.; Koopman, G.H. [Pennsylvania State Univ., University Park, PA (United States); Loth, J.L. [West Virginia Univ., Morgantown, WV (United States)

1993-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

MSID Products, Tools, & Services  

Science Conference Proceedings (OSTI)

SID Products, Tools, & Services. XML Testbed - collection of XML-Related Tools; Express Engine - STEP (ISO 10303) development ...

2013-09-16T23:59:59.000Z

162

Geothermal Lost Circulation Zone Mapping Tool  

DOE Green Energy (OSTI)

Lost circulation is an expensive and often encountered problem when drilling into geothermal formations. A method is needed to more accurately describe loss zones encountered during geothermal drilling to allow for more realistic testing since present testing techniques are inadequate. A Lost Circulation Zone Mapping Tool (LCZMT) is being developed that will quickly locate a loss zone and then provide a visual image of this zone as it intersects the wellbore. A modified Sandia high temperature Acoustic Borehole Televiewer should allow modeling of geothermal loss zones, which would in turn lead to testing that can be performed to evaluate lost circulation materials under simulated downhole conditions. 5 refs., 5 figs.

Bauman, T.J.

1985-01-01T23:59:59.000Z

163

Errors in Radio Acoustic Sounding of Temperature  

Science Conference Proceedings (OSTI)

With the use of simultaneous correction for radial wind, the accuracy of radio acoustic sounding systems for the measurement of temperature has been substantially improved. The temperature accuracy can now be affected by a number of factors that ...

Wayne M. Angevine; W. L. Ecklund

1994-06-01T23:59:59.000Z

164

Audioptimization : global-based acoustic design  

E-Print Network (OSTI)

Acoustic design is a difficult problem, because the human perception of sound depends on such things as decibel level, direction of propagation, and attenuation over time, none of which are tangible or visible. The advent ...

Monks, Michael Christopher, 1958-

1999-01-01T23:59:59.000Z

165

Weather Classification Using Passive Acoustic Drifters  

Science Conference Proceedings (OSTI)

Weather observations are needed in remote oceanic regions to support numerical weather forecast models, to provide surface truth for satellite sensors, and to help understand global weather patterns. An acoustic mini-drifting buoy using no moving ...

Jeffrey A. Nystuen; Harry D. Selsor

1997-06-01T23:59:59.000Z

166

An Acoustic Doppler and Electromagnetic Velocity Profiler  

Science Conference Proceedings (OSTI)

A freely failing current meter called the Absolute Velocity Profiler (AVP) is described. This profiler is an expansion of a previously developed instrument, the Electro-Magnetic Velocity Profiler (EMVP), with the additional capability of acoustic ...

Thomas B. Sanford; Robert G. Driver; John H. Dunlap

1985-06-01T23:59:59.000Z

167

Scattering of ion-acoustic solitons  

SciTech Connect

A series of experiments is described that is designed to ascertain the properties of the scattering of planar ion-acoustic solitons from objects of various shapes. The scattered solitons are compared with those radiated from the same objects.

Raychaudhuri, S.; Chang, H.; Tsikis, E.K.; Lonngren, K.E.

1985-07-01T23:59:59.000Z

168

Global Ocean Warming: An Acoustic Measure?  

Science Conference Proceedings (OSTI)

Explosions of 300 lbs of TNT at 1 km depth off Perth, Australia were recorded on Bermuda hydrophones, demonstrating 30 years age the feasibility of global acoustic transmissions. Climate-induced changes in ocean temperature (and hence in sound ...

W. H. Munk; A. M. G. Forbes

1989-11-01T23:59:59.000Z

169

Underwater acoustic MIMO OFDM: an experimental analysis  

E-Print Network (OSTI)

Performance of multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) is analyzed on an experimental shallow water acoustic channel. Different modulation levels, numbers of subcarriers and ...

Palou Visa, Guillem

170

Acoustic Energy Storage in Single Bubble Sonoluminescence  

E-Print Network (OSTI)

Single bubble sonoluminescence is understood in terms of a shock focusing towards the bubble center. We present a mechanism for significantly enhancing the effect of shock focusing, arising from the storage of energy in the acoustic modes of the gas. The modes with strongest coupling are not spherically symmetric. The storage of acoustic energy gives a framework for understanding how light intensities depend so strongly on ambient gases and liquids and suggests that the light intensities of successive flashes are highly correlated.

Michael P. Brenner; Sascha Hilgenfeldt; Detlef Lohse; Rodolfo R. Rosales

1996-05-07T23:59:59.000Z

171

Industrial Heat Recovery - 1982  

E-Print Network (OSTI)

Two years ago I summarized 20 years of experience on Industrial Heat Recovery for the Energy-source Technology Conference and Exhibition held in New Orleans, Louisiana. At the end of that paper I concluded with brief advice on 'How to specify heat recovery equipment.' The two years which have elapsed since then have convinced me that proper specification assures the most reliable equipment at the lowest price. The most economical specification describes the operating and site data but leaves the design details for the supplier. A true specialist will be able to provide you with the latest technology at the best possible price. This paper explores the impact of specifications on heat recovery equipment and its associated cost.

Csathy, D.

1982-01-01T23:59:59.000Z

172

Enhanced coalbed methane recovery  

SciTech Connect

The recovery of coalbed methane can be enhanced by injecting CO{sub 2} in the coal seam at supercritical conditions. Through an in situ adsorption/desorption process the displaced methane is produced and the adsorbed CO{sub 2} is permanently stored. This is called enhanced coalbed methane recovery (ECBM) and it is a technique under investigation as a possible approach to the geological storage of CO{sub 2} in a carbon dioxide capture and storage system. This work reviews the state of the art on fundamental and practical aspects of the technology and summarizes the results of ECBM field tests. These prove the feasibility of ECBM recovery and highlight substantial opportunities for interdisciplinary research at the interface between earth sciences and chemical engineering.

Mazzotti, M.; Pini, R.; Storti, G. [ETH, Zurich (Switzerland). Inst. of Process Engineering

2009-01-15T23:59:59.000Z

173

Building Energy Software Tools Directory: Indoor Humidity Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Tools Listed Alphabetically Tools by Platform Tools by Country Related Links Indoor Humidity Tools Indoor Humidity Tools logo. Integrated computer program intended to assist in...

174

Tunable damper for an acoustic wave guide  

DOE Patents (OSTI)

A damper for tunably damping acoustic waves in an ultrasonic waveguide is provided which may be used in a hostile environment such as a nuclear reactor. The area of the waveguide, which may be a selected size metal rod in which acoustic waves are to be damped, is wrapped, or surrounded, by a mass of stainless steel wool. The wool wrapped portion is then sandwiched between tuning plates, which may also be stainless steel, by means of clamping screws which may be adjusted to change the clamping force of the sandwiched assembly along the waveguide section. The plates are preformed along their length in a sinusoidally bent pattern with a period approximately equal to the acoustic wavelength which is to be damped. The bent pattern of the opposing plates are in phase along their length relative to their sinusoidal patterns so that as the clamping screws are tightened a bending stress is applied to the waveguide at 180/sup 0/ intervals along the damping section to oppose the acoustic wave motions in the waveguide and provide good coupling of the wool to the guide. The damper is tuned by selectively tightening the clamping screws while monitoring the amplitude of the acoustic waves launched in the waveguide. It may be selectively tuned to damp particular acoustic wave modes (torsional or extensional, for example) and/or frequencies while allowing others to pass unattenuated.

Rogers, S.C.

1982-10-21T23:59:59.000Z

175

Tunable damper for an acoustic wave guide  

DOE Patents (OSTI)

A damper for tunably damping acoustic waves in an ultrasonic waveguide is provided which may be used in a hostile environment such as a nuclear reactor. The area of the waveguide, which may be a selected size metal rod in which acoustic waves are to be damped, is wrapped, or surrounded, by a mass of stainless steel wool. The wool wrapped portion is then sandwiched between tuning plates, which may also be stainless steel, by means of clamping screws which may be adjusted to change the clamping force of the sandwiched assembly along the waveguide section. The plates are preformed along their length in a sinusoidally bent pattern with a period approximately equal to the acoustic wavelength which is to be damped. The bent pattern of the opposing plates are in phase along their length relative to their sinusoidal patterns so that as the clamping screws are tightened a bending stress is applied to the waveguide at 180.degree. intervals along the damping section to oppose the acoustic wave motions in the waveguide and provide good coupling of the wool to the guide. The damper is tuned by selectively tightening the clamping screws while monitoring the amplitude of the acoustic waves launched in the waveguide. It may be selectively tuned to damp particular acoustic wave modes (torsional or extensional, for example) and/or frequencies while allowing others to pass unattenuated.

Rogers, Samuel C. (Knoxville, TN)

1984-01-01T23:59:59.000Z

176

Apparatus for separating particles utilizing engineered acoustic contrast capture particles  

DOE Patents (OSTI)

An apparatus for separating particles from a medium includes a capillary defining a flow path therein that is in fluid communication with a medium source. The medium source includes engineered acoustic contrast capture particle having a predetermined acoustic contrast. The apparatus includes a vibration generator that is operable to produce at least one acoustic field within the flow path. The acoustic field produces a force potential minima for positive acoustic contrast particles and a force potential minima for negative acoustic contrast particles in the flow path and drives the engineered acoustic contrast capture particles to either the force potential minima for positive acoustic contrast particles or the force potential minima for negative acoustic contrast particles.

Kaduchak, Gregory (Los Alamos, NM); Ward, Michael D. (Los Alamos, NM)

2011-12-27T23:59:59.000Z

177

Proceedings of the 11th European Conference on Underwater Acoustics ACHIEVABLE RATES OF UNDERWATER ACOUSTIC OFDM  

E-Print Network (OSTI)

Proceedings of the 11th European Conference on Underwater Acoustics ACHIEVABLE RATES OF UNDERWATER-Telecom, Telecom Bretagne, UMR CNRS 6285 Lab-STICC, Ueb, Brest, France J.-M. Passerieux Thales Underwater Systems maintaining acceptable data rates, remains one of the major difficulty faced by underwater acoustic

Paris-Sud XI, Université de

178

Waste Steam Recovery  

E-Print Network (OSTI)

An examination has been made of the recovery of waste steam by three techniques: direct heat exchange to process, mechanical compression, and thermocompression. Near atmospheric steam sources were considered, but the techniques developed are equally applicable to other sources of steam. The interaction of the recovery system with the plant's steam/power system has been included. Typical operating economics have been prepared. It was found that the profitability of most recovery schemes is generally dependent on the techniques used, the existing steam/power system, and the relative costs of steam and power. However, there will always be site-specific factors to consider. It is shown that direct heat exchange and thermocompression will always yield an energy profit when interacting with PRVs in the powerhouse. A set of typical comparisons between the three recovery techniques, interacting with various powerhouse and plant steam system configurations, is presented. A brief outline of the analysis techniques needed to prepare the comparison is also shown. Only operating costs are examined; capital costs are so size - and site-specific as to be impossible to generalize. The operating cost savings may be used to give an indication of investment potential.

Kleinfeld, J. M.

1979-01-01T23:59:59.000Z

179

Recycling and Secondary Recovery  

Science Conference Proceedings (OSTI)

"Applying Ausmelt Technology to Recover Cu, Ni, and Co from Slags" .... " Enhancing Cobalt Recovery from Primary and Secondary Resources" .... " Modifying Alumina Red Mud to Support a Revegetation Cover" (Research .... " Recycling Used Automotive Oil Filters" (Research Summary), K.D. Peaslee, February 1994, pp.

180

Imaging of Acoustic Waves in Sand  

SciTech Connect

There is considerable interest in detecting objects such as landmines shallowly buried in loose earth or sand. Various techniques involving microwave, acoustic, thermal and magnetic sensors have been used to detect such objects. Acoustic and microwave sensors have shown promise, especially if used together. In most cases, the sensor package is scanned over an area to eventually build up an image or map of anomalies. We are proposing an alternate, acoustic method that directly provides an image of acoustic waves in sand or soil, and their interaction with buried objects. The INEEL Laser Ultrasonic Camera utilizes dynamic holography within photorefractive recording materials. This permits one to image and demodulate acoustic waves on surfaces in real time, without scanning. A video image is produced where intensity is directly and linearly proportional to surface motion. Both specular and diffusely reflecting surfaces can be accomodated and surface motion as small as 0.1 nm can be quantitatively detected. This system was used to directly image acoustic surface waves in sand as well as in solid objects. Waves as frequencies of 16 kHz were generated using modified acoustic speakers. These waves were directed through sand toward partially buried objects. The sand container was not on a vibration isolation table, but sat on the lab floor. Interaction of wavefronts with buried objects showed reflection, diffraction and interference effects that could provide clues to location and characteristics of buried objects. Although results are preliminary, success in this effort suggests that this method could be applied to detection of buried landmines or other near-surface items such as pipes and tanks.

Deason, Vance Albert; Telschow, Kenneth Louis; Watson, Scott Marshall

2003-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Method and apparatus of spectro-acoustically enhanced ultrasonic detection for diagnostics  

SciTech Connect

An apparatus for detecting a discontinuity in a material includes a source of electromagnetic radiation has a wavelength and an intensity sufficient to induce an enhancement in contrast between a manifestation of an acoustic property in the material and of the acoustic property in the discontinuity, as compared to when the material is not irradiated by the electromagnetic radiation. An acoustic emitter directs acoustic waves to the discontinuity in the material. The acoustic waves have a sensitivity to the acoustic property. An acoustic receiver receives the acoustic waves generated by the acoustic emitter after the acoustic waves have interacted with the material and the discontinuity. The acoustic receiver also generates a signal representative of the acoustic waves received by the acoustic receiver. A processor, in communication with the acoustic receiver and responsive to the signal generated by the acoustic receiver, is programmed to generate informational output about the discontinuity based on the signal generated by the acoustic receiver.

Vo-Dinh, Tuan (Knoxville, TN); Norton, Stephen J. (Raleigh, NC)

2001-01-01T23:59:59.000Z

182

Building Energy Software Tools Directory: ECOTECT  

NLE Websites -- All DOE Office Websites (Extended Search)

ECOTECT ECOTECT ECOTECT logo. Complete environmental design tool which couples an intuitive 3D modelling interface with extensive solar, thermal, lighting, acoustic and cost analysis functions. ECOTECT is one of the few tools in which performance analysis is simple, accurate and most importantly, visually responsive. ECOTECT is driven by the concept that environmental design principles are most effectively addressed during the conceptual stages of design. The software responds to this by providing essential visual and analytical feedback from even the simplest sketch model, progressively guiding the design process as more detailed information becomes available. The model is completely scalable, handling simple shading models to full-scale cityscapes. Its extensive export facilities also make final design

183

NEPA COMPLIANCE SURVEY Project Information Project Title: Express Stack Tools  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Express Stack Tools Express Stack Tools Date: 11/16/2010 DOE Code: 6730.020.81023 Contractor Code: 8067-971 Project Lead: Brian Black Project Overview 1) This project will test open and cased Hole logging tools in multiple wells. The tools to be testied include: 1. Brief project description [include anything that could impact the natural gamma, borehole temperature, compensated neutron, compensated density with PE, dual environment] induction/short guard, neutron prompt gamma, and acoustic televiewer tool. Radioactive sources will be run in the well as part of the toolstring. 2. Legal location 3. Duration of the project 2) 48-X-28 well location, SE %, SW %, Tsp 39N Rng 78W, Section 28; 45::3-X-21 well location, NE %, SW 4. Major equipment to be used %, Tsp 39N, Rng 78W, Section 21; 46-TpX-10 well location, NE %, SW Y.., Tsp38N, Rng 78W, Section 10.

184

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act Recovery Act Recovery Act Center Map PERFORMANCE The Department estimates the $6 billion Recovery Act investment will allow us to complete work now that would cost approximately $13 billion in future years, saving $7 billion. As Recovery Act work is completed through the cleanup of contaminated sites, facilities, and material disposition, these areas will becoming available for potential reuse by other entities. Recovery Act funding is helping the Department reach our cleanup goals faster. Through the end of December 2012, EM achieved a total footprint reduction of 74%, or 690 of 931 square miles. EM achieved its goal of 40% footprint reduction in April 2011, five months ahead of schedule. Recovery Act payments exceeded $5.9 billion in December 2012. Recovery Act

185

Recovery Act | OpenEI  

Open Energy Info (EERE)

Recovery Act Recovery Act Dataset Summary Description This dataset, updated quarterly by Recovery.org, contains a breakdown of state-by-state recovery act funds awarded and received, as well as the number of jobs created and saved. The shows two periods, February 17, 2009 to December 31, 2010, and January 1, 2011 to March 31, 2011. The jobs created and saved are displayed just for January 1, 2011 to March 31, 2011. The document was downloaded from Recovery.org. It is a simple document displaying 50 states, as well as American territories. Source Recovery.org Date Released June 08th, 2011 (3 years ago) Date Updated Unknown Keywords award funding jobs Recovery Act Recovery.org Data text/csv icon recipientfundingawardedbystate.csv (csv, 5.1 KiB) Quality Metrics Level of Review Some Review

186

COLORADO RECOVERY ACT SNAPSHOT | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

COLORADO RECOVERY ACT SNAPSHOT COLORADO RECOVERY ACT SNAPSHOT The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and...

187

Machine Tool Locator  

NLE Websites -- All DOE Office Websites (Extended Search)

gathered and used to set the position of the machine tool and to measure the size and shape of the machine tool tip, and examine cutting edge wear. April 18, 2013 machine tool...

188

The power tool  

Science Conference Proceedings (OSTI)

POWER Tool--Planning, Optimization, Waste Estimating and Resourcing tool, a hand-held field estimating unit and relational database software tool for optimizing disassembly and final waste form of contaminated systems and equipment.

HAYFIELD, J.P.

1999-02-01T23:59:59.000Z

189

Building Energy Software Tools Directory: CPF Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

CPF Tools CPF Tools CPF Tools logo CPF Tools is the market-leading software for solar installers connecting sales, system design and financing. Screen Shots Keywords Solar Sales, Quoting Tool, Proposal Tool, Solar Financing, Leads, Auto-Populate, Rebate Form, CRM software, Customer and Financing Dashboard Validation/Testing None Expertise Required Basic understanding of PV. Training is provided through our help site, which features training videos, a user community through Get Satisfaction, and user guides. We also offer live phone support and regular training webinars. Users More than 2,000 Audience Solar professionals, including installers, sales representatives, operations and system design specialists. We also offer a "Channel Manager" version of CPF Tools for manufacturers and distributors.

190

Symposium on enhanced oil recovery  

SciTech Connect

The Second Joint Symposium on Enhanced Oil Recovery was held in Tulsa, Oklahoma on April 5 to 8, 1981. Forty-four technical papers were presented which covered all phases of enhanced oil recovery. Field tests, laboratory investigations, and mathematical analyses of tertiary recovery methods such as microemulsion flooding, carbon dioxide injection, in-situ combustion, steam injection, and gas injection are presented.

Not Available

1981-01-01T23:59:59.000Z

191

Obama Administration Announces More Than $327 Million in Recovery Act  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 Million in Recovery 7 Million in Recovery Act Funding for Science Research Obama Administration Announces More Than $327 Million in Recovery Act Funding for Science Research August 4, 2009 - 12:00am Addthis Washington, D.C. - U.S Department of Energy Secretary Steven Chu announced today that more than $327 million in new funding from the American Recovery and Reinvestment Act will go toward scientific research, instrumentation, and laboratory infrastructure projects. Ten of DOE's national laboratories in six states will be receiving funds, along with researchers at institutions of higher learning across the nation. "These new initiatives will help to create new jobs while allowing the U.S. to maintain its scientific leadership and economic competitiveness ," said Secretary Steven Chu. "The projects provide vital funding and new tools for

192

Caustic Recovery Technology  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

366, REVISON 0 366, REVISON 0 Key Words: Waste Treatment Plant Sodium Recovery Electrochemical Retention: Permanent Review of Ceramatec's Caustic Recovery Technology W. R. Wilmarth D. T. Hobbs W. A. Averill E. B. Fox R. A. Peterson UNCLASSIFIED DOES NOT CONTAIN UNCLASSIFIED CONTROLLED NUCLEAR INFORMATION ADC & Reviewing Official:_______________________________________ (E. Stevens, Manager, Solid Waste and Special Programs) Date:______________________________________ JULY 20, 2007 Washington Savannah River Company Savannah River Site Aiken, SC 29808 Prepared for the U. S. Department of Energy Under Contract Number DE-AC09-96SR18500 Page 1 of 28 WSRC-STI-2007-00366, REVISON 0 DISCLAIMER This report was prepared for the United States Department of Energy under

193

Fermilab | Recovery Act | Videos  

NLE Websites -- All DOE Office Websites (Extended Search)

Videos Videos Watch videos documenting progress on Fermilab projects funded by the American Recovery and Reinvestment Act. NOvA - Community Voices - September 2009 Residents of northern Minnesota and construction workers building the NOvA detector facility discuss the benefits the high-energy physics research project has brought their communities. Congressman Bill Foster at Fermilab Congressman Bill Foster speaks to Fermilab Technical Division employees and members of the media at a press conference on Wednesday, August 5 to announce an additional $60.2 million in Recovery Act funds for the lab. NOvA first blast On July 20, construction crews began blasting into the rock at the future site of the NOvA detector facility in northern Minnesota. NOvA groundbreaking ceremony

194

Fermilab | Recovery Act | Features  

NLE Websites -- All DOE Office Websites (Extended Search)

Features - Archive Features - Archive photo Industrial Building 3 addition Fermilab Today-November 5, 2010 IB3 addition nears completion The future site of FermilabÂ’s new materials laboratory space has evolved from a steel outline to a fully enclosed building over the past five months. Read full column photo Fermilab Today-October 22, 2010 Recovery Act gives LBNE team chance to grow Thanks to funding from the American Recovery and Reinvestment Act, the collaboration for the Long-Baseline Neutrino Experiment, LBNE, has expanded its project team. Read full column photo cooling units Fermilab Today-October 15, 2010 Local company completes FCC roof construction A local construction company recently completed work on the roof of the Feynman Computing Center, an important step in an ongoing project funded by

195

Elemental sulfur recovery process  

DOE Patents (OSTI)

An improved catalytic reduction process for the direct recovery of elemental sulfur from various SO[sub 2]-containing industrial gas streams. The catalytic process provides combined high activity and selectivity for the reduction of SO[sub 2] to elemental sulfur product with carbon monoxide or other reducing gases. The reaction of sulfur dioxide and reducing gas takes place over certain catalyst formulations based on cerium oxide. The process is a single-stage, catalytic sulfur recovery process in conjunction with regenerators, such as those used in dry, regenerative flue gas desulfurization or other processes, involving direct reduction of the SO[sub 2] in the regenerator off gas stream to elemental sulfur in the presence of a catalyst. 4 figures.

Flytzani-Stephanopoulos, M.; Zhicheng Hu.

1993-09-07T23:59:59.000Z

196

Heavy crude oil recovery  

SciTech Connect

The oil crisis of the past decade has focused most of the attention and effort of researchers on crude oil resources, which are accepted as unrecoverable using known technology. World reserves are estimated to be 600-1000 billion metric tons, and with present technology 160 billion tons of this total can be recovered. This book is devoted to the discussion of Enhanced Oil Recovery (EOR) techniques, their mechanism and applicability to heavy oil reservoirs. The book also discusses some field results. The use of numerical simulators has become important, in addition to laboratory research, in analysing the applicability of oil recovery processes, and for this reason the last section of the book is devoted to simulators used in EOR research.

Okandan, E.

1984-01-01T23:59:59.000Z

197

Distributed Generation Heat Recovery  

Science Conference Proceedings (OSTI)

Economic and environmental drivers are promoting the adoption of combined heat and power (CHP) systems. Technology advances have produced new and improved distributed generation (DG) units that can be coupled with heat recovery hardware to create CHP systems. Performance characteristics vary considerably among DG options, and it is important to understand how these characteristics influence the selection of CHP systems that will meet both electric and thermal site loads.

2002-03-06T23:59:59.000Z

198

Recovery Boiler Modeling  

E-Print Network (OSTI)

Preliminary computations of the cold flow in a simplified geometry of a recovery boiler are presented. The computations have been carried out using a new code containing multigrid methods and segmentation techniques. This approach is shown to provide good resolution of the complex flow near the air ports and greatly improve the convergence characteristics of the numerical procedure. The improved resolution enhances the predictive capabilities of the computations, and allows the assessment of the relative performance of different air delivery systems.

Abdullah, Z.; Salcudean, M.; Nowak, P.

1994-04-01T23:59:59.000Z

199

13.853 Computational Ocean Acoustics, Spring 2003  

E-Print Network (OSTI)

Wave equations for fluid and visco-elastic media. Wave-theory formulations of acoustic source radiation and seismo-acoustic propagation in stratified ocean waveguides. Wavenumber Integration and Normal Mode methods for ...

Schmidt, Henrik

200

Acoustic measurement of the Deepwater Horizon Macondo well flow rate  

E-Print Network (OSTI)

On May 31, 2010, a direct acoustic measurement method was used to quantify fluid leakage rate from the Deepwater Horizon Macondo well prior to removal of its broken riser. This method utilized an acoustic imaging sonar and ...

Camilli, Richard

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Spatiotemporal processing and time-reversal for underwater acoustic communications  

E-Print Network (OSTI)

High-rate underwater acoustic communication can be achieved using transmitter/receiver arrays. Underwater acoustic channels can be characterized as rapidly time-varying systems that suffer severe Inter Symbol Interferences ...

Wang, Daniel Y

2005-01-01T23:59:59.000Z

202

Effects of Hydrogen on the Thermo-Acoustics Coupling Mechanisms...  

NLE Websites -- All DOE Office Websites (Extended Search)

on the Thermo-Acoustics Coupling Mechanisms of Low-Swirl Injector Flames in a Model Gas Turbine Combustor Title Effects of Hydrogen on the Thermo-Acoustics Coupling...

203

SPARSE UNDERWATER ACOUSTIC IMAGING: A CASE STUDY Nikolaos Stefanakis  

E-Print Network (OSTI)

SPARSE UNDERWATER ACOUSTIC IMAGING: A CASE STUDY Nikolaos Stefanakis , Jacques Marchal , Valentin de Beaulieu 35042 Rennes Cedex, France ABSTRACT Underwater acoustic imaging is traditionally 3D underwater imaging using a newly built flexible-configuration sonar device. The computational

Paris-Sud XI, Université de

204

Polaris: A GPS-Navigated Ocean Acoustic Current Profiler  

Science Conference Proceedings (OSTI)

Results from an initial feasibility study to test whether Global Positioning System (GPS) navigation can be combined with more traditional acoustic methods to measure ocean current profiles are presented. A typical acoustic current profiler such ...

Kevin D. Leaman; Peter S. Vertes; Chris Rocken

1995-06-01T23:59:59.000Z

205

Development and Testing of the MIT Acoustic Levitation Test Facilities  

Science Conference Proceedings (OSTI)

Two acoustic levitation test facilities have been developed for cloud physics experimentation. These facilities utilize acoustic standing wave energy to suspend both solid and liquid objects in a contact-free environment. In the still-air ...

Victor D. Lupi; R. John Hansman

1991-08-01T23:59:59.000Z

206

Ultrafast photo-acoustic spectroscopy of super-cooled liquids  

E-Print Network (OSTI)

Picosecond laser ultrasonic techniques for acoustic wave generation and detection were adapted to probe longitudinal and transverse acoustic waves in liquids at gigahertz frequencies. The experimental effort was designed ...

Klieber, Christoph

2010-01-01T23:59:59.000Z

207

Available Software Tools  

Science Conference Proceedings (OSTI)

... Climate Suitability Tool Logo, Climate Suitability Tool, A web application for ... Utility Software Icon, 1DZRead, A CONTAM 1D Zone Data file converter, ...

208

Chemically enhanced oil recovery  

Science Conference Proceedings (OSTI)

Yet when conducted according to present state of the art, chemical flooding (i.e., micellar/polymer flooding, surfactant/polymer flooding, surfactant flooding) can mobilize more residual crude oil than any other method of enhanced oil recovery. It also is one of the most expensive methods of enhanced oil recovery. This contribution will describe some of the technology that comprises the state of the art technology that must be adhered to if a chemical flood is to be successful. Although some of the efforts to reduce cost and other points are discussed, the principle focus is on technical considerations in designing a good chemical flooding system. The term chemical flooding is restricted here to methods of enhanced oil recovery that employs a surfactant, either injected into the oil reservoir or generated in situ, primarily to reduce oil-water interfacial tension. Hence, polymer-water floods for mobility or profile control, steam foams, and carbon dioxide foams are excluded. Some polymer considerations are mentioned because they apply to providing mobility control for chemical flooding systems.

Nelson, R.C.

1989-03-01T23:59:59.000Z

209

Acoustic Emission and Guided Wave Monitoring of Fatigue Crack Growth on a Full Pipe Specimen  

Science Conference Proceedings (OSTI)

Continuous on-line monitoring of active and passive systems, structures and components in nuclear power plants will be critical to extending the lifetimes of nuclear power plants in the US beyond 60 years. Acoustic emission and guided ultrasonic waves are two tools for continuously monitoring passive systems, structures and components within nuclear power plants and are the focus of this study. These tools are used to monitor fatigue damage induced in a SA 312 TP304 stainless steel pipe specimen. The results of acoustic emission monitoring indicate that crack propagation signals were not directly detected. However, acoustic emission monitoring exposed crack formation prior to visual confirmation through the detection of signals caused by crack closure friction. The results of guided ultrasonic wave monitoring indicate that this technology is sensitive to the presence and size of cracks. The sensitivity and complexity of GUW signals is observed to vary with respect to signal frequency and path traveled by the guided ultrasonic wave relative to the crack orientation.

Meyer, Ryan M.; Cumblidge, Stephen E.; Ramuhalli, Pradeep; Watson, Bruce E.; Doctor, Steven R.; Bond, Leonard J.

2011-05-06T23:59:59.000Z

210

NASA Glenn Research Center Acoustical Testing Laboratory: Five year retrospective  

Science Conference Proceedings (OSTI)

In the five years since the NASA Glenn Research Center Acoustical Testing Laboratory (ATL) opened its doors in September

2005-01-01T23:59:59.000Z

211

Cooperative Schemes for Underwater Acoustic Communications (AQU 3)  

E-Print Network (OSTI)

Cooperative Schemes for Underwater Acoustic CommunicationsIntroduction: Underwater Cooperative CommunicationsMotivation Traditional underwater communications Used for

Madhavan Vajapeyam; Satish Vedantam; Urbashi Mitra

2006-01-01T23:59:59.000Z

212

Building Energy Software Tools Directory: Tools by Platform ...  

NLE Websites -- All DOE Office Websites (Extended Search)

HVAC acoustics, sound level prediction, noise level Software has been updated. Acuity Energy Platform energy efficiency software; customized business recommendation; commercial...

213

Building Energy Software Tools Directory: Tools by Country -...  

NLE Websites -- All DOE Office Websites (Extended Search)

HVAC acoustics, sound level prediction, noise level Software has been updated. Acuity Energy Platform energy efficiency software; customized business recommendation; commercial...

214

Building Energy Software Tools Directory: Tools by Subject -...  

NLE Websites -- All DOE Office Websites (Extended Search)

HVAC acoustics, sound level prediction, noise level AnTherm Thermal heat bridges, heat flow, steady state, 2D, 3D, transfer coefficients, thermal conductance,...

215

Acoustic Propagation Prediction in Shallow Water  

E-Print Network (OSTI)

An acoustic propagation experiment was conducted on 17 May 2000 in a shallow water site off the Perth metropolitan coast with the view of obtaining reflection and refraction data to contribute to developing a geoacoustic model of the area. The site proposed has constant bathymetry, though the geological properties of the site are not well known. The experiment used two hydrophones, one situated mid-water and the other moored to the seabed to explore the possibility of receiving head waves. The acoustic sources used were a 20-cui air gun and imploding sources comprising 60W and 75W light globes and purpose built evacuated spheres.

Justin Hoffman John; John D. Penrose; Darryl R. Mcmahon

2000-01-01T23:59:59.000Z

216

Ion acoustic shock waves in degenerate plasmas  

SciTech Connect

Korteweg de Vries Burgers equation for negative ion degenerate dissipative plasma has been derived using reductive perturbation technique. The quantum hydrodynamic model is used to study the quantum ion acoustic shock waves. The effects of different parameters on quantum ion acoustic shock waves are studied. It is found that quantum parameter, electrons Fermi temperature, temperature of positive and negative ions, mass ratio of positive to negative ions, viscosity, and density ratio have significant impact on the shock wave structure in negative ion degenerate plasma.

Akhtar, N. [Theoretical Plasma Physics Division, PINSTECH, Nilore, Islamabad 44000 Pakistan (Pakistan); Hussain, S. [Theoretical Plasma Physics Division, PINSTECH, Nilore, Islamabad 44000 Pakistan (Pakistan); Department of Physics and Applied Mathematics, PIEAS, Nilore, Islamabad 44000 Pakistan (Pakistan)

2011-07-15T23:59:59.000Z

217

Acoustic microscope surface inspection system and method  

DOE Patents (OSTI)

An acoustic microscope surface inspection system and method in which pulses of high frequency electrical energy are applied to a transducer which forms and focuses acoustic energy onto a selected location on the surface of an object and receives energy from the location and generates electrical pulses. The phase of the high frequency electrical signal pulses are stepped with respected to the phase of a reference signal at said location. An output signal is generated which is indicative of the surface of said selected location. The object is scanned to provide output signals representative of the surface at a plurality of surface locations.

Khuri-Yakub, Butrus T. (Palo Alto, CA); Parent, Philippe (Chilly-Mazarin, FR); Reinholdtsen, Paul A. (Seattle, WA)

1991-01-01T23:59:59.000Z

218

Electron-acoustic vortices in multicomponent magnetoplasma  

Science Conference Proceedings (OSTI)

Linear and nonlinear properties of electron-acoustic waves in a multicomponent magnetoplasma comprising of cold and beam electrons and two species of thermal unmagnetized ions are investigated here. It is found that the electron beam velocity, electron Debye length, electron Larmor radius, and concentration of the cold and beam electrons affect the linear dispersion characteristics of electron-acoustic wave. It is also found that such a multicomponent plasma admits dipolar and vortex street type structures for the normalized electrostatic potential PHIgeomagnetic tail, etc. is also pointed out.

Haque, Q. [Theoretical Plasma Physics Division, PINSTECH, P. O. Nilore, Islamabad 45320 (Pakistan); Mirza, Arshad M. [Department of Physics, Theoretical Plasma Physics Group, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Nargis, Shahida [Department of Mathematics, Quaid-i-Azam University, Islamabad 45320 (Pakistan)

2010-05-15T23:59:59.000Z

219

Point interactions in acoustics: one dimensional models  

E-Print Network (OSTI)

A one dimensional system made up of a compressible fluid and several mechanical oscillators, coupled to the acoustic field in the fluid, is analyzed for different settings of the oscillators array. The dynamical models are formulated in terms of singular perturbations of the decoupled dynamics of the acoustic field and the mechanical oscillators. Detailed spectral properties of the generators of the dynamics are given for each model we consider. In the case of a periodic array of mechanical oscillators it is shown that the energy spectrum presents a band structure.

C. Cacciapuoti; R. Figari; A. Posilicano

2005-04-28T23:59:59.000Z

220

Underwater acoustic imaging: physically-motivated sparse models  

E-Print Network (OSTI)

Underwater acoustic imaging: physically-motivated sparse models and validation on real data N hal-00677287,version1-4Jun2012 #12;Underwater acoustic imaging (UWA)hal-00677287,version1-4Jun2012 #12;Underwater acoustic imaging: direct problem Successive emission sequences, or pings, indexed by p. ep

Paris-Sud XI, Université de

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Proceedings of the 11 European Conference on Underwater Acoustics  

E-Print Network (OSTI)

Proceedings of the 11 th European Conference on Underwater Acoustics INCOHERENT CHANGE DETECTION on Underwater Acoustics images. This allows performing a segmentation of the master image at the coarser stage,version1-7Sep2012 #12;Proceedings of the 11 th European Conference on Underwater Acoustics The idea

Paris-Sud XI, Université de

222

Building Energy Software Tools Directory: Tools by Subjects  

NLE Websites -- All DOE Office Websites (Extended Search)

Envelope Systems HVAC Equipment & Systems Lighting Systems Other Applications Tools Listed Alphabetically Tools by Platform Tools by Country Related Links Tools by Subject...

223

Building Energy Software Tools Directory: Indoor Humidity Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Tools by Platform PC Mac UNIX Internet Tools by Country Related Links Indoor Humidity Tools Indoor Humidity Tools logo. Integrated computer program intended to assist in...

224

Stridulatory organ morphology, acoustics, and function in the red imported fire ant  

E-Print Network (OSTI)

The purpose of this research was to determine whether stridulation in the red imported fire ant (RIFA) serves a significant communicative function. Three general objectives were developed. 1) Characterize the stridulatory organ (SO). 2) Determine the information content of the signal through an acoustics analysis; and 3) Determine colony level employment of the SO. Characterization of the morphology of the SO revealed a general increase in all SO parameters (length, width, distance between teeth, and total teeth) in relation to ant size. This was most evident in the worker caste. The SO was significantly different between castes suggesting that the resulting acoustical properties could serve to distinguish each caste. Morphological analysis revealed that the SO of males is thin and unlikely to be very functional. Based on the differences in the structure of the SO between female castes, the possible evolution of the SO is discussed. Characterization of the acoustical properties, pulse length and pulse carrier frequency for both directions of gaster movement, showed that both were variable and overlapped between the female castes. This suggests that signals are not altered for different contexts (Markl et. al. 1977). Pulse lengths for both directions of gaster movement were the only properties shown to be significantly different between castes, while short pulse frequency was the only acoustical property found correlated to ant size. These differences are discussed in terms of selection, as opposed to allometric variation or developmental processes. Three colony level behaviors associated with RIFAs, disturbance response, emigration, and excavation, were examined for SO employment. Stridulation was not associated with mound disturbance or employed during nest emigration. However, stridulations were found to be significantly employed during soil excavation. Thus, sound may be serving one or more possible functions: 1) As an aid in the removal of soil particles; 2) As a signal communicating a need to dig; 3) As an acoustical imaging tool; and 4. As an aid in mound construction via particle compression and the expulsion of interstitial water.

Rauth, Steven Joseph

2001-01-01T23:59:59.000Z

225

Comprehensive Municipal Solid Waste Management, Resource Recovery...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Municipal Solid Waste Management, Resource Recovery, and Conservation Act (Texas) Comprehensive Municipal Solid Waste Management, Resource Recovery, and Conservation...

226

Building Energy Software Tools Directory: Solar Tool  

NLE Websites -- All DOE Office Websites (Extended Search)

Skip to Content U.S. Department of Energy Energy Efficiency and Renewable Energy EERE Home | Programs & Offices | Consumer Information Building Energy Software Tools Directory...

227

Building Energy Software Tools Directory: Weather Tool  

NLE Websites -- All DOE Office Websites (Extended Search)

result is a comprehensive pre-design climatesite analysis tool. Screen Shots Keywords weather data visualization, psychrometry, passive design analysis, optimum orientiation,...

228

Building Energy Software Tools Directory: New Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Auditing & Sales Tool, home energy assessments, energy analysis, home performance, residential retrofits 2013-05-17 MyVerdafero Utility Optimization, building performance,...

229

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

Science Conference Proceedings (OSTI)

This technical progress report describes work performed from July 1 through September, 2003 for the project ''Heavy and Thermal Oil Recovery Production Mechanisms,'' DE-FC26-00BC15311. In this project, a broad spectrum of research is undertaken related to thermal and heavy-oil recovery. The research tools and techniques span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history-matching techniques. During this period, work focused on completing project tasks in the area of multiphase flow and rock properties. The area of interest is the production mechanisms of oil from porous media at high temperature. Temperature has a beneficial effect on oil recovery and reduces residual oil saturation. Work continued to delineate how the wettability of reservoir rock shifts from mixed and intermediate wet conditions to more water-wet conditions as temperature increases. One mechanism for the shift toward water-wet conditions is the release of fines coated with oil-wet material from pore walls. New experiments and theory illustrate the role of temperature on fines release.

Anthony R. Kovscek; Louis M. Castanier

2004-03-01T23:59:59.000Z

230

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

Science Conference Proceedings (OSTI)

This technical progress report describes work performed from January 1 through March 31, 2003 for the project ''Heavy and Thermal Oil Recovery Production Mechanisms,'' DE-FC26-00BC15311. In this project, a broad spectrum of research is undertaken related to thermal and heavy-oil recovery. The research tools and techniques span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history matching techniques. During this period, previous analysis of experimental data regarding multidimensional imbibition to obtain shape factors appropriate for dual-porosity simulation was verified by comparison among analytic, dual-porosity simulation, and fine-grid simulation. We continued to study the mechanisms by which oil is produced from fractured porous media at high pressure and high temperature. Temperature has a beneficial effect on recovery and reduces residual oil saturation. A new experiment was conducted on diatomite core. Significantly, we show that elevated temperature induces fines release in sandstone cores and this behavior may be linked to wettability. Our work in the area of primary production of heavy oil continues with field cores and crude oil. On the topic of reservoir definition, work continued on developing techniques that integrate production history into reservoir models using streamline-based properties.

Anthony R. Kovscek

2003-04-01T23:59:59.000Z

231

Effects of a Thermistor String Mounted between the Acoustic Beams of an Acoustic Doppler Current Profiler  

Science Conference Proceedings (OSTI)

A useful extension of upward-looking buoy-mounted acoustic Doppler current profilers (ADCPs), in particular for studying surface-mixed-layer dynamics from underneath, would be to combine them with a thermistor cable for obtaining simultaneous ...

Friedrich Schott

1988-02-01T23:59:59.000Z

232

URANIUM RECOVERY PROCESS  

DOE Patents (OSTI)

A method is described for recovering uranium values from uranium bearing phosphate solutions such as are encountered in the manufacture of phosphate fertilizers. The solution is first treated with a reducing agent to obtain all the uranium in the tetravalent state. Following this reduction, the solution is treated to co-precipitate the rcduced uranium as a fluoride, together with other insoluble fluorides, thereby accomplishing a substantially complete recovery of even trace amounts of uranium from the phosphate solution. This precipitate usually takes the form of a complex fluoride precipitate, and after appropriate pre-treatment, the uranium fluorides are leached from this precipitate and rccovered from the leach solution.

Bailes, R.H.; Long, R.S.; Olson, R.S.; Kerlinger, H.O.

1959-02-10T23:59:59.000Z

233

Laundry heat recovery system  

SciTech Connect

A laundry heat recovery system includes a heat exchanger associated with each dryer in the system, the heat exchanger being positioned within the exhaust system of the dryer. A controller responsive to the water temperature of the heat exchangers and the water storage for the washer selectively circulates the water through a closed loop system whereby the water within the exchangers is preheated by the associated dryers. By venting the exhaust air through the heat exchanger, the air is dehumidified to permit recirculation of the heated air into the dryer.

Alio, P.

1985-04-09T23:59:59.000Z

234

The ALEXIS mission recovery  

SciTech Connect

The authors report the recovery of the ALEXIS small satellite mission. ALEXIS is a 113-kg satellite that carries an ultrasoft x-ray telescope array and a high-speed VHF receiver/digitizer (BLACKBEARD), supported by a miniature spacecraft bus. It was launched by a Pegasus booster on 1993 April 25, but a solar paddle was damaged during powered flight. Initial attempts to contact ALEXIS were unsuccessful. The satellite finally responded in June, and was soon brought under control. Because the magnetometer had failed, the rescue required the development of new attitude control-techniques. The telemetry system has performed nominally. They discuss the procedures used to recover the ALEXIS mission.

Bloch, J.; Armstrong, T.; Dingler, B.; Enemark, D.; Holden, D.; Little, C.; Munson, C.; Priedhorsky, B.; Roussel-Dupre, D.; Smith, B. [Los Alamos National Lab., NM (United States); Warner, R.; Dill, B.; Huffman, G.; McLoughlin, F.; Mills, R.; Miller, R. [AeroAstro, Inc., Herndon, VA (United States)

1994-03-01T23:59:59.000Z

235

Acoustic Radar Studies of Rain Microphysics  

Science Conference Proceedings (OSTI)

Raindrop size distributions are obtained from the Doppler frequency spectrum of an acoustic radar. Number concentrations of 12 drop diameters with a minimum diameter 0.14 cm are obtained and averaged over 3–15 min at 20-m range gates from 20 to ...

S. G. Bradley

1997-06-01T23:59:59.000Z

236

The Acoustic Properties of Different Noise Sources  

Science Conference Proceedings (OSTI)

This paper discusses a method to find the acoustic properties of different types of background noise: highway, airport, subway, restaurant, rain, inside a car, and inside a train. Four parameters are calculated using the Auto Correlation Function (ACF). ... Keywords: Environmental noise, noise classification

Jidong Yang; Buket D. Barkana

2009-04-01T23:59:59.000Z

237

Uncanny soundscapes: Towards an inoperative acoustic community  

Science Conference Proceedings (OSTI)

Drawing on field research carried out in the abandoned villages of the Ara Valley, this article seeks to readdress notions of acoustic community and communication in terms of a 'haptic aurality' in which listening, as a mode of touch, approximates a ...

Iain Foreman

2011-12-01T23:59:59.000Z

238

Acoustic Environment of Admiralty Inlet: Broadband Noise Measurements  

SciTech Connect

Admiralty Inlet has been selected as a potential tidal energy site. It is located near shipping lanes, is a highly variable acoustic environment, and is frequented by the highly endangered southern resident killer whale (SRKW). Resolving environmental impacts is the first step to receiving approval to deploy tidal turbines at Admiralty Inlet. Of particular concern is the potential for blade strike or other negative interactions between the SRKW and the tidal turbine. A variety of technologies including passive and active monitoring systems are being considered as potential tools to determine the presence of SRKW in the vicinity of the turbines. Broadband noise level measurements are critical for the determination of design and operation specifications of all marine and hydrokinetic energy capture technologies. Acoustic environment data at the proposed site was acquired at different depths using a cabled vertical line array (VLA) with four calibrated hydrophones. The sound pressure level (SPL) power spectrum density was estimated based on the fast Fourier transform. This study describes the first broadband SPL measurements for this site at different depths with frequency ranging from 10 kHz to 480 kHz in combination with other information. To understand the SPL caused by this bedload transport, three different pressure sensors with temperature and conductivity were also assembled on the VLA to measure the conditions at the hydrophone deployment depth. The broadband SPL levels at frequency ranges of 3 kHz to 7 kHz as a function of depth were estimated. Only the hydrophone at an average depth of 40 m showed the strong dependence of SPL with distance from the bottom, which was possibly caused by the cobbles shifting on the seabed. Automatic Identification System data were also studied to understand the SPL measurements.

Xu, Jinshan; Deng, Zhiqun; Martinez, Jayson J.; Carlson, Thomas J.; Myers, Joshua R.; Weiland, Mark A.; Jones, Mark E.

2011-09-30T23:59:59.000Z

239

Cross-Dipole Acoustic Log | Open Energy Information  

Open Energy Info (EERE)

Cross-Dipole Acoustic Log Cross-Dipole Acoustic Log Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Cross-Dipole Acoustic Log Details Activities (1) Areas (1) Regions (0) NEPA(0) Exploration Technique Information Exploration Group: Downhole Techniques Exploration Sub Group: Well Log Techniques Parent Exploration Technique: Acoustic Logs Information Provided by Technique Lithology: Stratigraphic/Structural: Rock stress and fracture analysis Hydrological: Use for fracture identification in open and cased holes. Also used for evaluating hydro fracturing/well stimulation effectiveness. Thermal: Dictionary.png Cross-Dipole Acoustic Log: An acoustic logging technique where the acoustic transmitter and receivers are lowered down hole and waveforms that travel through the well mud,

240

Recovery Act State Memos Ohio  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

20 20 For total Recovery Act jobs numbers in Ohio go to www.recovery.gov DOE Recovery Act projects in Ohio: 83 U.S. DEPARTMENT OF ENERGY * OHIO RECOVERY ACT SNAPSHOT The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and environmental future. The Recovery Act investments in Ohio are supporting a broad range of clean energy projects from the smart grid and energy efficiency to advanced battery manufacturing, biofuels, carbon capture and storage, and cleanup of the state's Cold War legacy nuclear sites Through these investments, Ohio's businesses, universities, non-profits, and local governments are creating quality jobs today and positioning Ohio to play an important role in the new energy economy of the future. EXAMPLES OF OHIO FORMULA GRANTS Program

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Economy » Recovery Act Energy Economy » Recovery Act Recovery Act December 18, 2013 BPA Wins Platts Global Energy Award for Grid Optimization Platts awarded the Bonneville Power Administration (BPA) a Global Energy Award for grid optimization on December 12 in New York City for its development of a synchrophasor network. BPA is part of the Recovery Act-funded Western Interconnection Synchrophasor Program. December 13, 2013 Cumulative Federal Payments to OE Recovery Act Recipients, through November 30, 2013 Graph of cumulative Federal Payments to OE Recovery Act Recipients, through November 30, 2013. December 12, 2013 Energy Department Announces $150 Million in Tax Credits to Invest in U.S. Clean Energy Manufacturing Domestic Manufacturing Projects to Support Renewable Energy Generation as

242

Resource Conservation and Recovery Act  

NLE Websites -- All DOE Office Websites (Extended Search)

Resource Conservation and Recovery Act (RCRA) Resource Conservation and Recovery Act (RCRA) In 1965 the Solid Waste Disposal Act [Public Law (Pub. L.) 89-72] was enacted to improve solid waste disposal methods. It was amended in 1970 by the Resource Recovery Act (Pub. L. 91-512), which provided the Environmental Protection Agency (EPA) with funding for resource recovery programs. However, that Act had little impact on the management and ultimate disposal of hazardous waste. In 1976 Congress enacted the Resource Conservation and Recovery Act (RCRA, Pub. L. 94-580). RCRA established a system for managing non-hazardous and hazardous solid wastes in an environmentally sound manner. Specifically, it provides for the management of hazardous wastes from the point of origin to the point of final disposal (i.e., "cradle to grave"). RCRA also promotes resource recovery and waste minimization.

243

Recovery Act State Memos Louisiana  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Louisiana Louisiana For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

244

Recovery Act State Memos Alabama  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Alabama Alabama For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

245

Recovery Act State Memos Oklahoma  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oklahoma Oklahoma For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

246

Recovery Act State Memos Massachusetts  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Massachusetts Massachusetts For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

247

Recovery Act State Memos Mississippi  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Mississippi Mississippi For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

248

Recovery Act State Memos Wyoming  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wyoming Wyoming For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 ELECTRIC GRID ........................................................................................................ 4

249

Recovery Act State Memos Connecticut  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Connecticut Connecticut For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

250

Recovery Act State Memos Oregon  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oregon Oregon For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 4 RENEWABLE ENERGY ............................................................................................. 5

251

Recovery Act State Memos Utah  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Utah Utah For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

252

Recovery Act State Memos Nebraska  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Nebraska Nebraska For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

253

Recovery Act State Memos Alaska  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Alaska Alaska For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

254

Recovery Act State Memos Arkansas  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Arkansas Arkansas For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

255

Recovery Act State Memos Indiana  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Indiana Indiana For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

256

Recovery Act State Memos Guam  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Guam Guam For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 ELECTRIC GRID ........................................................................................................ 4

257

Recovery Act State Memos Iowa  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Iowa Iowa For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

258

Recovery Act State Memos Texas  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Texas Texas For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 7

259

Recovery Act State Memos Vermont  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Vermont Vermont For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................ 4

260

Recovery Act State Memos Michigan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Michigan Michigan For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Recovery Act State Memos Tennessee  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Tennessee Tennessee For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

262

Recovery Act State Memos Hawaii  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hawaii Hawaii For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

263

Recovery Act State Memos Georgia  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Georgia Georgia For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

264

Recovery Act State Memos Minnesota  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Minnesota Minnesota For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

265

Recovery Act State Memos Idaho  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Idaho Idaho For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

266

Recovery Act State Memos Illinois  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Illinois Illinois For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 7

267

Recovery Act State Memos Pennsylvania  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Pennsylvania Pennsylvania For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................ 3 RENEWABLE ENERGY ......................................................................................... 7

268

Recovery Act State Memos Wisconsin  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wisconsin Wisconsin For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 6

269

Recovery Act State Memos Montana  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Montana Montana For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

270

Recovery Act State Memos Arizona  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Arizona Arizona For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

271

Recovery Act State Memos Kansas  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Kansas Kansas For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

272

Recovery Act State Memos California  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

California California For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY .............................................................................................. 3 RENEWABLE ENERGY ............................................................................................ 12

273

Recovery Act State Memos Washington  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Washington Washington For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 6

274

Recovery Act State Memos Nevada  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Nevada Nevada For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ................................................................................................ 1 RENEWABLE ENERGY ............................................................................................. 5

275

Recovery Act State Memos Virginia  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Virginia Virginia For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

276

Recovery Act State Memos Maine  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maine Maine For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

277

Recovery Act State Memos Missouri  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Missouri Missouri For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

278

Recovery Act State Memos Maryland  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maryland Maryland For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ....................................................................................................... 3 RENEWABLE ENERGY ..................................................................................................... 4

279

Recovery Act State Memos Colorado  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Colorado Colorado For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 6

280

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Research and Commercialization New green jobs a benefit of effort to end dependence on foreign oil April 29, 2009 Secretary Chu Announces 93 Million from Recovery Act to...

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Economic Recovery Loan Program (Maine)  

Energy.gov (U.S. Department of Energy (DOE))

The Economic Recovery Loan Program provides subordinate financing to help businesses remain viable and improve productivity. Eligibility criteria are based on ability to repay, and the loan is...

282

Recovery Act | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Reports Calendar Year Reports Recovery Act Peer Reviews DOE Directives Performance Strategic Plan Testimony Financial Statements Semiannual Reports Work Plan Mission About Us...

283

Recovery Act State Memos Delaware  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

weatherization efforts in the state, creating jobs, reducing carbon emissions, and saving money for Delaware's low-income families. Over the course of the Recovery Act,...

284

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

SciTech Connect

The Stanford University Petroleum Research Institute (SUPRI-A) studies oil recovery mechanisms relevant to thermal and heavy-oil production. The scope of work is relevant across near-, mid-, and long-term time frames. In August of 2000 we received funding from the U. S. DOE under Award No. DE-FC26-00BC15311 that completed December 1, 2003. The project was cost shared with industry. Heavy oil (10 to 20{sup o} API) is an underutilized energy resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods. Heating reduces oil viscosity dramatically. Hence, thermal recovery is especially important because adding heat, usually via steam injection generally improves displacement efficiency. The objectives of this work were to improve our understanding of the production mechanisms of heavy oil under both primary and enhanced modes of operation. The research described spanned a spectrum of topics related to heavy and thermal oil recovery and is categorized into: (1) multiphase flow and rock properties, (2) hot fluid injection, (3) improved primary heavy-oil recovery, (4) in-situ combustion, and (5) reservoir definition. Technology transfer efforts and industrial outreach were also important to project effort. The research tools and techniques used were quite varied. In the area of experiments, we developed a novel apparatus that improved imaging with X-ray computed tomography (CT) and high-pressure micromodels etched with realistic sandstone roughness and pore networks that improved visualization of oil-recovery mechanisms. The CT-compatible apparatus was invaluable for investigating primary heavy-oil production, multiphase flow in fractured and unfractured media, as well as imbibition. Imbibition and the flow of condensed steam are important parts of the thermal recovery process. The high-pressure micromodels were used to develop a conceptual and mechanistic picture of primary heavy-oil production by solution gas drive. They allowed for direct visualization of gas bubble formation, bubble growth, and oil displacement. Companion experiments in representative sands and sandstones were also conducted to understand the mechanisms of cold production. The evolution of in-situ gas and oil saturation was monitored with CT scanning and pressure drop data. These experiments highlighted the importance of depletion rate, overburden pressure, and oil-phase chemistry on the cold production process. From the information provided by the experiments, a conceptual and numerical model was formulated and validated for the heavy-oil solution gas drive recovery process. Also in the area of mechanisms, steamdrive for fractured, low permeability porous media was studied. Field tests have shown that heat injected in the form of steam is effective at unlocking oil from such reservoir media. The research reported here elucidated how the basic mechanisms differ from conventional steamdrive and how these differences are used to an advantage. Using simulations of single and multiple matrix blocks that account for details of heat transfer, capillarity, and fluid exchange between matrix and fracture, the importance of factors such as permeability contrast between matrix and fracture and oil composition were quantified. Experimentally, we examined the speed and extent to which steam injection alters the permeability and wettability of low permeability, siliceous rocks during thermal recovery. Rock dissolution tends to increase permeability moderately aiding in heat delivery, whereas downstream the cooled fluid deposits silica reducing permeability. Permeability reduction is not catastrophic. With respect to wettability, heat shifts rock wettability toward more water wet conditions. This effect is beneficial for the production of heavy and medium gravity oils as it improves displacement efficiency. A combination of analytical and numerical studies was used to examine the efficiency of reservoir heating using nonconventional wells such as horizontal and multi

Anthony R. Kovscek; Louis M. Castanier

2003-12-31T23:59:59.000Z

285

Case tool evaluation system  

SciTech Connect

An automated system that uses an analytical approach to evaluate Computer-Aided Software Engineering (CASE) tools is currently being developed. this system is referred to as the CASE Tool Evaluation System. The following general criteria will be used: overall tool functionality; tool stability; cost; interfaces with other software; customization; ease of use; output produced; hardware and operating system needs; documentation; training and vendor support; repository interface; methodologies; and vendor stability. in Phase 1 CASE tools will be eliminated that do not meet certain must-have'' characteristics specified by the user. Phase 2 will further reduce the size of the tool list by retaining those tools that possess desirable, but not absolutely necessary'' characteristics, also specified by the user. Phase 3 will employ the Analytic Hierarchy Process, developed by Dr. Thomas L. Saaty, to rank the tools. Users will be able to supply tools of their own choosing, in addition to tools that are generated via normal use of the system. All three phases will interact with a database that stores objective information about CASE tools. The use of the Analytic Hierarchy process (AHP) distinguishes this method of CASE tool evaluation from others. As used in this system, the AHP is a method of breaking down the complex, unstructured problem of selecting a CASE tool into its component evaluation criteria and candidate tools. These criteria and tools are arranged into a hierarchical order. Each criterion and tool is assigned a subjective numerical value (by experts or users or both). These values are then synthesized to determine which have the highest priority. The result will be a ranked list of CASE tools tailored to the needs and desires of the user.

Green, P.L.; Andreae, P.V.; Pennewell, W.J.; Clinard, L.A.; Thomas, B. Jr.; Tarrant, P.M.

1989-01-01T23:59:59.000Z

286

Fermilab | Recovery Act  

NLE Websites -- All DOE Office Websites (Extended Search)

NOvA NOvA In April 2010, workers set up two cranes at the construction site for the NOvA detector facility in Ash River, Minnesota. In 2009, the U.S. Department of Energy's Office of Science, under the American Recovery and Reinvestment Act, provided DOE's Fermi National Accelerator Laboratory with $114.2 million. Fermilab invested the funds in critical scientific infrastructure to strengthen the nation's global scientific leadership as well as to provide immediate economic relief to local communities. This Web site provided citizens with clear and accurate information about how Fermilab used the new funding and its immediate benefits for our neighbors and our nation. Features photo Industrial Building 3 addition Fermilab Today-November 5, 2010 IB3 addition nears completion

287

Enhanced oil recovery system  

DOE Patents (OSTI)

All energy resources available from a geopressured geothermal reservoir are used for the production of pipeline quality gas using a high pressure separator/heat exchanger and a membrane separator, and recovering waste gas from both the membrane separator and a low pressure separator in tandem with the high pressure separator for use in enhanced oil recovery, or in powering a gas engine and turbine set. Liquid hydrocarbons are skimmed off the top of geothermal brine in the low pressure separator. High pressure brine from the geothermal well is used to drive a turbine/generator set before recovering waste gas in the first separator. Another turbine/generator set is provided in a supercritical binary power plant that uses propane as a working fluid in a closed cycle, and uses exhaust heat from the combustion engine and geothermal energy of the brine in the separator/heat exchanger to heat the propane.

Goldsberry, Fred L. (Spring, TX)

1989-01-01T23:59:59.000Z

288

Energy recovery system  

DOE Patents (OSTI)

The present invention is directed to an improved wet air oxidation system and method for reducing the chemical oxygen demand (COD) of waste water used from scrubbers of coal gasification plants, with this COD reduction being sufficient to effectively eliminate waste water as an environmental pollutant. The improvement of the present invention is provided by heating the air used in the oxidation process to a temperature substantially equal to the temperature in the oxidation reactor before compressing or pressurizing the air. The compression of the already hot air further heats the air which is then passed in heat exchange with gaseous products of the oxidation reaction for "superheating" the gaseous products prior to the use thereof in turbines as the driving fluid. The superheating of the gaseous products significantly minimizes condensation of gaseous products in the turbine so as to provide a substantially greater recovery of mechanical energy from the process than heretofore achieved.

Moore, Albert S. (Morgantown, WV); Verhoff, Francis H. (Morgantown, WV)

1980-01-01T23:59:59.000Z

289

Speech recovery device  

DOE Patents (OSTI)

There is provided an apparatus and method for assisting speech recovery in people with inability to speak due to aphasia, apraxia or another condition with similar effect. A hollow, rigid, thin-walled tube with semi-circular or semi-elliptical cut out shapes at each open end is positioned such that one end mates with the throat/voice box area of the neck of the assistor and the other end mates with the throat/voice box area of the assisted. The speaking person (assistor) makes sounds that produce standing wave vibrations at the same frequency in the vocal cords of the assisted person. Driving the assisted person's vocal cords with the assisted person being able to hear the correct tone enables the assisted person to speak by simply amplifying the vibration of membranes in their throat.

Frankle, Christen M.

2000-10-19T23:59:59.000Z

290

Flash Steam Recovery Project  

E-Print Network (OSTI)

One of the goals of Vulcan's cost reduction effort is to reduce energy consumption in production facilities through energy optimization. As part of this program, the chloromethanes production unit, which produces a wide variety of chlorinated organic compounds, was targeted for improvement. This unit uses a portion of the high-pressure steam available from the plant's cogeneration facility. Continuous expansions within the unit had exceeded the optimum design capacity of the unit's steam/condensate recovery system, resulting in condensate flash steam losses to the atmosphere. Using computer simulation models and pinch analysis techniques, the Operational Excellence Group (Six Sigma) was able to identify a project to recover the flash steam losses as a supplemental low-pressure steam supply. The project was designed and implemented at no capital cost using existing instrumentation and controls. On an annualized basis steam usage per ton of product fell by about three percent. Absolute savings were about 15,800 million Btu.

Bronhold, C. J.

2000-04-01T23:59:59.000Z

291

Speech recovery device  

SciTech Connect

There is provided an apparatus and method for assisting speech recovery in people with inability to speak due to aphasia, apraxia or another condition with similar effect. A hollow, rigid, thin-walled tube with semi-circular or semi-elliptical cut out shapes at each open end is positioned such that one end mates with the throat/voice box area of the neck of the assistor and the other end mates with the throat/voice box area of the assisted. The speaking person (assistor) makes sounds that produce standing wave vibrations at the same frequency in the vocal cords of the assisted person. Driving the assisted person's vocal cords with the assisted person being able to hear the correct tone enables the assisted person to speak by simply amplifying the vibration of membranes in their throat.

Frankle, Christen M.

2000-10-19T23:59:59.000Z

292

Recovery Act: State Assistance for Recovery Act Related Electricity  

NLE Websites -- All DOE Office Websites (Extended Search)

State State Assistance for Recovery Act Related Electricity Policies Recovery Act: State Assistance for Recovery Act Related Electricity Policies $44 Million for State Public Utility Commissions State public utility commissions (PUCs), which regulate and oversee electricity projects in their states, will be receiving more than $44.2 million in Recovery Act funding to hire new staff and retrain existing employees to ensure they have the capacity to quickly and effectively review proposed electricity projects. The funds will help the individual state PUCs accelerate reviews of the large number of electric utility requests that are expected under the Recovery Act. State PUCs will be reviewing electric utility investments in projects such as energy efficiency, renewable energy, carbon capture and storage, transmission

293

OOTW COST TOOLS  

Science Conference Proceedings (OSTI)

This document reports the results of a study of cost tools to support the analysis of Operations Other Than War (OOTW). It recommends the continued development of the Department of Defense (DoD) Contingency Operational Support Tool (COST) as the basic cost analysis tool for 00TWS. It also recommends modifications to be included in future versions of COST and the development of an 00TW mission planning tool to supply valid input for costing.

HARTLEY, D.S.III; PACKARD, S.L.

1998-09-01T23:59:59.000Z

294

Adjustable cutting tool holder  

DOE Patents (OSTI)

This patent application describes a device for varying the geometry of a cutting tool for use in machining operations.

Steinhour, William Lee III; West, Drew; Honeycutt, Steve; Frank, Steven; Krishnamurthy, Kallutla

2000-09-21T23:59:59.000Z

295

Caliper and contour tool  

SciTech Connect

The disclosure relates to a tool for borehole logging comprising a plurality of extendable caliper arms to determine borehole contour.

Fink, Conrad F. (Los Alamos, NM)

1981-01-01T23:59:59.000Z

296

Computer Forensics Tool Testing  

Science Conference Proceedings (OSTI)

Computer Forensics Tool Testing (CFTT). Summary: For more information, visit: http://www.cftt.nist.gov/. There is a critical ...

2010-10-05T23:59:59.000Z

297

AMO Software Tools  

Energy.gov (U.S. Department of Energy (DOE))

This presentation, hosted by the Advanced Manufacturing Office, provides an overview of tools and resources available for industrial energy management

298

MONITORING POWER PLANT EFFICIENCY USING THE MICROWAVE-EXCITED THERMAL-ACOUSTIC EFFECT TO MEASURE UNBURNED CARBON  

Science Conference Proceedings (OSTI)

The objective of this project is to explore microwave-excited thermal-acoustic (META) phenomena for quantitative analysis of granular and powdered materials, with the culmination of the research to be an on-line carbon-in-ash monitor for coal-fired power plants. This technique of analyzing unburned carbon in fly ash could be a less tedious and time consuming method as compared to the traditional LOI manual procedure. Phase 1 of the research focused on off-line single-frequency thermal-acoustic measurements where an off-line fly ash monitor was constructed that could operate as analytical tool to explore instrument and methodology parameters for quantifying the microwave-excited thermal-acoustic effect of carbon in fly ash, and it was determined that the off-line thermal-acoustic technique could predict the carbon content of a random collection of fly ashes with a linear correlation constant of R{sup 2} = 0.778. Much higher correlations are expected for fly ashes generated from a single boiler. Phase 2 of the research developing a methodology to generate microwave spectra of various powders, including fly ash, coal, and inorganic minerals, and to determine if these microwave spectra could be used for chemical analyses. Although different minerals produced different responses, higher resolution microwave spectra would be required to be able to distinguish among minerals. Phase 3 of the research focused on the development of an on-line fly ash monitor that could be adapted to measure either a thermal-acoustic or thermal-elastic response to due microwave excitation of fly ash. The thermal-acoustic response was successfully employed for this purpose but the thermal-elastic response was too weak to yield a useful on-line device.

Robert C. Brown; Robert J. Weber; Jeffrey J. Swetelitsch

2005-01-01T23:59:59.000Z

299

Heat Recovery From Solid Waste  

E-Print Network (OSTI)

More opportunity exists today for the successful implementation of resource recovery projects than at any other period. However, that doesn't mean that energy/resource recovery exists for everyone. You must have a favorable match of all the critical areas of evaluation, including the cost of fuel, cost of solid waste disposal, plant energy requirements, available technology, etc.

Underwood, O. W.

1981-01-01T23:59:59.000Z

300

Metal recovery from porous materials  

DOE Patents (OSTI)

The present invention relates to recovery of metals. More specifically, the present invention relates to the recovery of plutonium and other metals from porous materials using microwaves. The United States Government has rights in this invention pursuant to Contract No. DE-AC09-89SR18035 between the US Department of Energy and Westinghouse Savannah River Company.

Sturcken, E.F.

1991-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

ARM - ARM Recovery Act Project FAQs  

NLE Websites -- All DOE Office Websites (Extended Search)

ActARM Recovery Act Project FAQs ActARM Recovery Act Project FAQs Recovery Act Logo Subscribe FAQs Recovery Act Instruments Recovery Act Fact Sheet March 2010 Poster (PDF, 10MB) External Resources Recovery Act - Federal Recovery Act - DOE Recovery Act - ANL Recovery Act - BNL Recovery Act - LANL Recovery Act - PNNL Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send ARM Recovery Act Project FAQs Why is ARM buying new instruments and equipment? The ARM Climate Research Facility (ARM) is receiving $60 million dollars in Recovery Act funding from the U.S. Department of Energy Office of Science to build the next generation facility for climate change research. Using input from past ARM user workshops and ARM working group discussion, ARM has planned for the purchase and deployment of an expansive array of new

302

Argonne Acoustic Levitation Video Goes Viral  

NLE Websites -- All DOE Office Websites (Extended Search)

"Inside the Advanced Photon Source" Inside the latest Argonne Now "Inside the Advanced Photon Source" Inside the latest Argonne Now APS Director Stephenson Named Argonne Distinguished Fellow Advanced Photon Source, Canadian Light Source Strengthen Ties, Expand X-ray Technology and Research Rose of APS and CNM One of Four DOE Early Career Award Winners Scientists Close-In on Artificial Spider Silk APS News Archives: 2012 | 2011 | 2010 | 2009 2008 | 2007 | 2006 | 2005 2004 | 2003 | 2002 | 2001 2000 Subscribe to APS News rss feed Argonne Acoustic Levitation Video Goes Viral SEPTEMBER 25, 2012 Bookmark and Share Drops of solution being suspended for a long period of time, thanks to the vibrational force of sound waves that keep them stationary in an air column. More than 41,000 Google hits for "acoustic levitation Argonne" as of

303

Acoustic data transmission through a drillstring  

DOE Patents (OSTI)

A method and apparatus for acoustically transmitting data along a drillstring is presented. In accordance with one embodiment of the present invention, acoustic data signals are conditioned to counteract distortions caused by the drillstring. Preferably, this conditioning step comprises multiplying each frequency component of the data signal by exp (-ikL) where L is the transmission length of the drillstring, k is the wave number in the drillstring at the frequency of each component and i is (-1).sup.1/2. In another embodiment of this invention, data signals having a frequency content in at least one passband of the drillstring are generated preferably traveling in only one direction (e.g., up the drillstring) while echoes in the drillstring resulting from the data transmission are suppressed.

Drumheller, Douglas S. (Cedar Crest, NM)

1992-01-01T23:59:59.000Z

304

Methods And Apparatus For Acoustic Fiber Fractionation  

DOE Patents (OSTI)

Methods and apparatus for acoustic fiber fractionation using a plane ultrasonic wave field interacting with water suspended fibers circulating in a channel flow using acoustic radiation forces to separate fibers into two or more fractions based on fiber radius, with applications of the separation concept in the pulp and paper industry. The continuous process relies on the use of a wall-mounted, rectangular cross-section piezoelectric ceramic transducer to selectively deflect flowing fibers as they penetrate the ultrasonic field. The described embodiment uses a transducer frequency of approximately 150 kHz. Depending upon the amount of dissolved gas in water, separation is obtained using a standing or a traveling wave field.

Brodeur, Pierre (Smyrna, GA)

1999-11-09T23:59:59.000Z

305

Multipurpose Acoustic Sensor for Downhole Fluid Monitoring  

Science Conference Proceedings (OSTI)

The projects objectives and purpose are to: (1) development a multipurpose acoustic sensor for downhole fluid monitoring in Enhanced Geothermal Systems (EGS) reservoirs over typical ranges of pressures and temperatures and demonstrate its capabilities and performance for different EGS systems; (2) determine in real-time and in a single sensor package several parameters - temperature, pressure, fluid flow and fluid properties; (3) needed in nearly every phase of an EGS project, including Testing of Injection and Production Wells, Reservoir Validation, Inter-well Connectivity, Reservoir Scale Up and Reservoir Sustainability. (4) Current sensors are limited to operating at lower temperatures, but the need is for logging at high temperatures. The present project deals with the development of a novel acoustic-based sensor that can work at temperatures up to 374 C, in inhospitable environments.

Pantea, Cristian [Los Alamos National Laboratory

2012-05-04T23:59:59.000Z

306

Acoustic data transmission through a drillstring  

DOE Patents (OSTI)

A method and apparatus for acoustically transmitting data along a drillstring are presented. In accordance with one embodiment of the present invention, acoustic data signals are conditioned to counteract distortions caused by the drillstring. Preferably, this conditioning step comprises multiplying each frequency component of the data signal by exp ([minus]ikL) where L is the transmission length of the drillstring, k is the wave number in the drillstring at the frequency of each component and i is ([minus]1)[sup 1/2]. In another embodiment of this invention, data signals having a frequency content in at least one passband of the drillstring are generated preferably traveling in only one direction (e.g., up the drillstring) while echoes in the drillstring resulting from the data transmission are suppressed. 20 figs.

Drumheller, D.S.

1992-07-07T23:59:59.000Z

307

Pulse combusted acoustic agglomeration apparatus and process  

SciTech Connect

An improved apparatus and process for removal of particulates entrained in a gas stream are provided. The removal process employs a pulse combustor to provide an acoustic pressure wave to acoustically enhance bimodal agglomeration of particulates which may be collected and removed using a conventional separation apparatus. A particulate having a size different from the size of the particulate in the gas stream to be cleaned is introduced into the system to effectuate the bimodal process. The apparatus may be employed as a direct fired system for improved operation of gas-operated equipment such as a gas turbine, or may, alternatively, be employed as an add-on subsystem for combustion exhaust clean-up. Additionally, the added particulate may be a sorbent for effecting sorption of other contaminants such as sulfur. Various other particulates for contaminant removal may also be introduced into the system as exemplified by alkali-gettering agents.

Mansour, Momtaz N. (Columbia, MD)

1993-01-01T23:59:59.000Z

308

Pulse combusted acoustic agglomeration apparatus and process  

SciTech Connect

An improved apparatus and process for removal of particulates entrained in a gas stream are provided. The removal process employs a pulse combustor to provide an acoustic pressure wave to acoustically enhance agglomeration of particulates which may be collected and removed using a conventional separation apparatus. The apparatus may be employed as a direct fired system for improved operation of gas-operated equipment such as a gas turbine, or may, alternatively, be employed as an add-on subsystem for combustion exhaust clean-up. Additionally, added particulates may include a sorbent for effecting sorption of other contaminants such as sulfur. Various other particulates for contaminant removal may also be introduced into the system as exemplified by alkali-gettering agents.

Mansour, Momtaz N. (Columbia, MD); Chandran, Ravi (Ellicott City, MD)

1994-01-01T23:59:59.000Z

309

Recovery | National Nuclear Security Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery | National Nuclear Security Administration Recovery | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Recovery Home > About Us > Our Programs > Emergency Response > Planning for Emergencies > Recovery Recovery NNSA ensures that capabilities are in place to respond to any NNSA and Department of Energy facility emergency. It is also the nation's premier

310

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

26, 2010 26, 2010 200,000 Homes Weatherized Under the Recovery Act -- Video from Cathy Zoi Vice President Biden announced that 200,000 homes have been Weatherized under the Recovery Act. Hear what Cathy Zoi, Assistant Secretary for Energy Efficiency and Renewable Energy, has to say on Weatherization. August 26, 2010 200,000 homes weatherized under the Recovery Act August 25, 2010 The Recovery Act: Cutting Costs and Upping Capacity Secretary Chu joined Vice President Joe Biden at the White House to help unveil a new report on how investments made through the Recovery Act have been impacting innovation. While the report analyzed several major sectors, its most striking findings centered on energy. August 25, 2010 Eco Technologies, Inc., hired eleven workers to install these solar panels at the Hillsborough County judicial center. | Photo courtesy of Hillsborough County

311

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

31, 2009 31, 2009 Energy Secretary Chu Announces $755 Million in Recovery Act Funding for Environmental Cleanup in Tennessee New Funding Will Create Jobs and Accelerate Cleanup Efforts March 31, 2009 Energy Secretary Chu Announces $1.615 Billion in Recovery Act Funding for Environmental Cleanup in South Carolina New Funding Will Create Jobs and Accelerate Cleanup Efforts March 31, 2009 Energy Secretary Chu Announces $138 Million in Recovery Act Funding for Environmental Cleanup in Ohio New Funding Will Create Jobs and Accelerate Cleanup Efforts March 31, 2009 Energy Secretary Chu Announces $148 million in Recovery Act Funding for Environmental Cleanup in New York New Funding Will Create Jobs and Accelerate Cleanup Efforts March 31, 2009 Energy Secretary Chu Announces $384 Million in Recovery Act Funding for

312

Recovery Act | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Act Act Recovery Act Total Federal Payments to OE Recovery Act Recipients by Month, through November 30, 2013 Total Federal Payments to OE Recovery Act Recipients by Month, through November 30, 2013 American Recovery and Reinvestment Act Overview PROJECTS TOTAL OBLIGATIONS AWARD RECIPIENTS Smart Grid Investment Grant $3,482,831,000 99 Smart Grid Regional and Energy Storage Demonstration Projects $684,829,000 42 Workforce Development Program $100,000,000 52 Interconnection Transmission Planning $80,000,000 6 State Assistance for Recovery Act Related Electricity Policies $48,619,000 49 Enhancing State Energy Assurance $43,500,000 50 Enhancing Local Government Energy Assurance $8,024,000 43 Interoperability Standards and Framework $12,000,000 1 Program Direction1 $27,812,000 --

313

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act Recovery Act Recovery Act The American Recovery and Reinvestment Act of 2009 -- commonly called the "stimulus" -- was designed to spur economic growth while creating new jobs and saving existing ones. Through the Recovery Act, the Energy Department invested more than $31 billion to support a wide range of clean energy projects across the nation -- from investing in the smart grid and developing alternative fuel vehicles to helping homeowners and businesses reduce their energy costs with energy efficiency upgrades and deploying carbon capture and storage technologies. The Department's programs helped create new power sources, conserve resources and aligned the nation to lead the global energy economy. Featured Leaders of the Fuel Cell Pack Fuel cell forklifts like the one shown here are used by leading companies across the U.S. as part of their daily business operations. | Energy Department file photo.

314

Infill drilling enhances waterflood recovery  

Science Conference Proceedings (OSTI)

Two sets of west Texas carbonate reservoir and waterflood data were studied to evaluate the impact of infill drilling on waterflood recovery. Results show that infill drilling enhanced the current and projected waterflood recovery from most of the reservoirs. The estimated ultimate and incremental infill-drilling waterflood recovery was correlated with well spacing and other reservoir and process parameters. Results of the correlation indicate that reducing well spacing from 40 to 20 acres (16 to 8 ha) per well would increase the oil recovery by 8 to 9% of the original oil in place (OOIP). Because of the limited data base and regressional nature of the correlation models, the infill-drilling recovery estimate must be used with caution.

Wu, C.H.; Jardon, M. (Texas A and M Univ., College Station, TX (USA)); Laughlin, B.A. (Union Pacific Research Co. (US))

1989-10-01T23:59:59.000Z

315

A Single-Objective Recovery Phase Model  

Science Conference Proceedings (OSTI)

The Federal Emergency Management Agency FEMA has identified the four phases of disaster related planning as mitigation, preparation, response, and recovery. The recovery phase is characterized by activity to return life to normal or improved levels. ... Keywords: Disaster Recovery, Disaster Recovery Strategy, Optimization, Recovery, Response, Transportation Model

Sandy Mehlhorn; Michael Racer; Stephanie Ivey; Martin Lipinski

2011-07-01T23:59:59.000Z

316

Acoustic enhancement for photo detecting devices  

DOE Patents (OSTI)

Provided are improvements to photo detecting devices and methods for enhancing the sensitivity of photo detecting devices. A photo detecting device generates an electronic signal in response to a received light pulse. An electro-mechanical acoustic resonator, electrically coupled to the photo detecting device, damps the electronic signal and increases the signal noise ratio (SNR) of the electronic signal. Increased photo detector standoff distances and sensitivities will result.

Thundat, Thomas G; Senesac, Lawrence R; Van Neste, Charles W

2013-02-19T23:59:59.000Z

317

Silent Positioning in Underwater Acoustic Sensor Networks  

E-Print Network (OSTI)

In this paper, we present a silent positioning scheme termed as UPS for underwater acoustic sensor networks. UPS relies on the time-difference of arrivals measured locally at a sensor to detect range differences from the sensor to four anchor nodes. These range differences are averaged over multiple beacon intervals before they are combined to estimate the 3D sensor location through trilateration. UPS requires no time-synchronization and provides location privacy at underwater vehicles/sensors whose locations need to be determined. To study the performance of UPS, we model the underwater acoustic channel as a modified Ultra Wide Band (UWB) S-V model: the arrival of each path cluster and paths within each cluster follow double Poisson distributions, and the multipath channel gain follows a Rician distribution. Based on this channel model, we perform both theoretical analysis and simulation study on the position error of UPS under acoustic fading channels. The obtained results indicate that UPS is an effective scheme for underwater vehicle/sensor self-positioning.

Xiuzhen Cheng; Haining Shu; Qilian Liang; David Hung-chang Du

2007-01-01T23:59:59.000Z

318

Tool setting device  

DOE Patents (OSTI)

The present invention relates to a tool setting device for use with numerically controlled machine tools, such as lathes and milling machines. A reference position of the machine tool relative to the workpiece along both the X and Y axes is utilized by the control circuit for driving the tool through its program. This reference position is determined for both axes by displacing a single linear variable displacement transducer (LVDT) with the machine tool through a T-shaped pivotal bar. The use of the T-shaped bar allows the cutting tool to be moved sequentially in the X or Y direction for indicating the actual position of the machine tool relative to the predetermined desired position in the numerical control circuit by using a single LVDT.

Brown, Raymond J. (Clinton, TN)

1977-01-01T23:59:59.000Z

319

Underwater Acoustic Detection of Ultra High Energy Neutrinos  

E-Print Network (OSTI)

We investigate the acoustic detection method of 10^18-20 eV neutrinos in a Mediterranean Sea environment. The acoustic signal is re-evaluated according to dedicated cascade simulations and a complex phase dependant absorption model, and compared to previous studies. We detail the evolution of the acoustic signal as function of the primary shower characteristics and of the acoustic propagation range. The effective volume of detection for a single hydrophone is given taking into account the limitations due to sea bed and surface boundaries as well as refraction effects. For this 'benchmark detector' we present sensitivity limits to astrophysical neutrino fluxes, from which sensitivity bounds for a larger acoustic detector can be derived. Results suggest that with a limited instrumentation the acoustic method would be more efficient at extreme energies, above 10^20 eV.

V. Niess; V. Bertin

2005-11-21T23:59:59.000Z

320

Building Energy Software Tools Directory: Tools by Subjects  

NLE Websites -- All DOE Office Websites (Extended Search)

SolarClimate Analysis Training Utility Evaluation Validation Tools VentilationAirflow Water Conservation Miscellaneous Applications Tools Listed Alphabetically Tools by...

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Wastewater heat recovery apparatus  

DOE Patents (OSTI)

A heat recovery system with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature.

Kronberg, James W. (108 Independent Blvd., Aiken, SC 29801)

1992-01-01T23:59:59.000Z

322

Wastewater heat recovery apparatus  

DOE Patents (OSTI)

A heat recovery system is described with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature. 6 figs.

Kronberg, J.W.

1992-09-01T23:59:59.000Z

323

URANIUM RECOVERY PROCESS  

DOE Patents (OSTI)

The recovery of uranium from the acidic aqueous metal waste solutions resulting from the bismuth phosphate carrier precipitation of plutonium from solutions of neutron irradiated uranium is described. The waste solutions consist of phosphoric acid, sulfuric acid, and uranium as a uranyl salt, together with salts of the fission products normally associated with neutron irradiated uranium. Generally, the process of the invention involves the partial neutralization of the waste solution with sodium hydroxide, followed by conversion of the solution to a pH 11 by mixing therewith sufficient sodium carbonate. The resultant carbonate-complexed waste is contacted with a titanated silica gel and the adsorbent separated from the aqueous medium. The aqueous solution is then mixed with sufficient acetic acid to bring the pH of the aqueous medium to between 4 and 5, whereby sodium uranyl acetate is precipitated. The precipitate is dissolved in nitric acid and the resulting solution preferably provided with salting out agents. Uranyl nitrate is recovered from the solution by extraction with an ether such as diethyl ether.

Hyman, H.H.; Dreher, J.L.

1959-07-01T23:59:59.000Z

324

Electret Acoustic Transducer Array For Computerized Ultrasound Risk Evaluation System  

DOE Patents (OSTI)

An electret-based acoustic transducer array is provided and may be used in a system for examining tissue. The acoustic transducer array is formed with a substrate that has a multiple distinct cells formed therein. Within each of the distinct cells is positioned an acoustic transducing element formed of an electret material. A conductive membrane is formed over the distinct cells and may be flexible.

Moore, Thomas L. (Livermore, CA); Fisher, Karl A. (Brentwood, CA)

2005-08-09T23:59:59.000Z

325

CX-005601: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1: Categorical Exclusion Determination CX-005601: Categorical Exclusion Determination The Oil Recovery Tool: Acoustic Source for Increased Oil Production CX(s) Applied: B3.6 Date:...

326

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Inc. FE Hydroacoutstics 2010 Project SCNGO FY11 Gary Covatch 12 months Torrey, NY The Oil Recovery Tool: Acoustic Source for Increased Oil Production Development of an oil...

327

CX-005484: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4: Categorical Exclusion Determination CX-005484: Categorical Exclusion Determination The Oil Recovery Tool: Acoustic Source for Increased Oil Production CX(s) Applied: B3.6 Date:...

328

Levitation as a Tool in Argonne Lab | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Levitation as a Tool in Argonne Lab Levitation as a Tool in Argonne Lab Levitation as a Tool in Argonne Lab March 19, 2013 - 4:54pm Addthis Scientists at Argonne National Laboratory have discovered a way to use sound waves to levitate individual droplets of solutions containing different pharmaceuticals. Watch all Argonne videos on their video page. Michael Hess Michael Hess Former Digital Communications Specialist, Office of Public Affairs What are the key facts? Droplets are suspended in air between two sets of speakers, which generate sound waves at frequencies slightly above the audible range -- about 22 kilohertz. Back in September, Argonne National Lab posted the YouTube video "Acoustic Levitation" featuring physicist Chris Benmore suspending droplets of liquid between two speakers. It almost immediately went viral garnering

329

Improved recovery demonstration for Williston Basin carbonates  

SciTech Connect

The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in- place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional (3D) and multi- component seismic are being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short- lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimates of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

Carrell, L. A., Luff Exploration Co., Denver, CO

1996-09-01T23:59:59.000Z

330

Improved Recovery Demonstration for Williston Basin Carbonates  

SciTech Connect

The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in- place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional (3-D) and multi- component seismic are being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short- lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimate of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

1997-03-01T23:59:59.000Z

331

Improved Recovery Demonstration for Williston Basin Carbonates  

SciTech Connect

The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in-place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing three-dimensional is being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short-lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimates of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

Larry A. Carrell

1997-12-31T23:59:59.000Z

332

Improved Recovery Demonstration for Williston Basin Carbonates.  

SciTech Connect

The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in- place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional (3-D) and multi-component seismic are being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short-lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimate of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

1997-12-31T23:59:59.000Z

333

Improved recovery demonstration for Williston Basin carbonates  

SciTech Connect

The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determination of oil-in-place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional (3D) is being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimates of oil-in- place will result in additional oil production by primary and enhanced recovery processes.

Carrell, L. A., Luff Exploration Co., Denver, CO

1997-12-01T23:59:59.000Z

334

Acoustic ranging technique with application to assessment of low-frequency acoustic noise of wind turbines  

DOE Green Energy (OSTI)

Impulsive low-frequency noise from wind turbines can cause annoyance particularly when a residential structure is involved. Such noise is typically generated in some spatially restricted region of a turbine rotor swept area. Low-frequency impulsive noise of the MOD-1 turbine was generated when the rotor blades passed downwind of the tower legs encountering the complex unsteady flows there. An acoustic ranging technique that aids assessment of the degree of concentration of acoustic generation within the turbine swept area and which determines the time-average spatial source region of such concentration is described. Practical applications and limitations of the process are discussed.

Hemphill, R.

1983-05-01T23:59:59.000Z

335

Building Energy Software Tools Directory: Solar Tool  

NLE Websites -- All DOE Office Websites (Extended Search)

Solar Tool Solar Tool Solar Tool logo. Makes the process of accurately sizing and positioning overhangs, shading devices and louvers easy. This software is a must for architects, planners and building services engineers, anyone who needs to quickly determine the extent of solar penetration into buildings, overshadowing or the most appropriate means of shading a window. The program uses a flexible, parametric model on which can be placed any number of horizontal, vertical and detached shades. You can select any date, time or location, seeing immediately the resulting shadows whilst interactively manipulating the geometry to show immediately the effects. You can also choose to automatically optimise the size and shape of any shading device over any range of dates and times you require. Screen Shots

336

Underwater Acoustic Sensor Network with Energy Harvesting Nodes.  

E-Print Network (OSTI)

??This thesis explores the possibility of a self sustained and service free Underwater Acoustic Sensor Network (UASN). The network nodes are installed along a subsea… (more)

Huseby, Morten

2011-01-01T23:59:59.000Z

337

WIRELESS MICROWAVE ACOUSTIC SENSOR SYSTEM FOR CONDITION MONITORING...  

NLE Websites -- All DOE Office Websites (Extended Search)

WIRELESS MICROWAVE ACOUSTIC SENSOR SYSTEM FOR CONDITION MONITORING IN POWER PLANT ENVIRONMENTS Project DE-FE0007379TDD NETL, Morgantown, WV, March 14, 2012. DOE NETL Program:...

338

Nondestructive acoustic electric field probe apparatus and method  

DOE Patents (OSTI)

The disclosure relates to a nondestructive acoustic electric field probe and its method of use. A source of acoustic pulses of arbitrary but selected shape is placed in an oil bath along with material to be tested across which a voltage is disposed and means for receiving acoustic pulses after they have passed through the material. The received pulses are compared with voltage changes across the material occurring while acoustic pulses pass through it and analysis is made thereof to determine preselected characteristics of the material.

Migliori, Albert (Santa Fe, NM)

1982-01-01T23:59:59.000Z

339

MAC and Routing Protocols for Mobile Underwater Acoustic Sensor Swarms  

E-Print Network (OSTI)

Pressure Routing for Underwater Sensor Networks . . . . . .of Aloha Protocols for Underwater Acoustic Sensor Networks.Critical Applications in Underwater Sensor Networks. In

Noh, Young Tae

2012-01-01T23:59:59.000Z

340

Use of an acoustic network as an underwater positioning system .  

E-Print Network (OSTI)

??Underwater acoustic networks provide an interface between UUVs and surface or land-based control systems. By exploiting range data measured incidental to communications on these networks… (more)

Reed, Michael S.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Using Scanning Acoustic Microscopy to Study Subsurface Defects ...  

Science Conference Proceedings (OSTI)

The resolution of the reflection acoustic microscope is somewhat better than the resolution based on the Rayleigh criterion and is given by the equation6: ...

342

COMPARISON OF ACOUSTIC AND ELECTRICAL IMAGE LOGS FROM THE COSO...  

Open Energy Info (EERE)

fractures are difficult to identify in electrical image logs because of the low percentage of the borehole wall imaged. Analysis of induced structures in acoustic image logs...

343

High Frequency Acoustic Wave Scattering From Turbulent Premixed Flames .  

E-Print Network (OSTI)

??This thesis describes an experimental investigation of high frequency acoustic wave scattering from turbulent premixed flames. The objective of this work was to characterize the… (more)

Narra, Venkateswarlu

2008-01-01T23:59:59.000Z

344

Recovery tasks: an automated approach to failure recovery  

Science Conference Proceedings (OSTI)

We present a new approach for developing robust software applications that breaks dependences on the failed parts of an application's execution to allow the rest of the application to continue executing. When a failure occurs, the recovery algorithm ...

Brian Demsky; Jin Zhou; William Montaz

2010-11-01T23:59:59.000Z

345

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

Science Conference Proceedings (OSTI)

This technical progress report describes work performed from October 1 through December 31, 2002 , for the project ''Heavy and Thermal Oil Recovery Production Mechanisms.'' In this project, a broad spectrum of research is undertaken related to thermal and heavy-oil recovery. The research tools and techniques used are varied and span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history-matching techniques. During this period, experimental data regarding multidimensional imbibition was analyzed to obtain shape factors appropriate for dual-porosity simulation. It is shown that the usual assumption of constant, time-independent shape factors is incorrect. In other work, we continued to study the mechanisms by which oil is produced from fractured media at high pressure and high temperature. High temperature significantly increased the apparent wettability and affected water relative permeability of cores used in previous experiments. A phenomenological and mechanistic cause for this behavior is sought. Our work in the area of primary production of heavy oil continues with field cores and crude oil. On the topic of reservoir definition, work continued on developing techniques that integrate production history into reservoir models using streamline-based properties.

Anthony R. Kovscek

2003-01-01T23:59:59.000Z

346

Petroleum recovery materials and process  

SciTech Connect

A petroleum recovery process uses micellar solutions made from liquefied petroleum gas (LPG). During the process, microemulsions utilizing LPG in the external phase are injected through at least one injection well into the oil-bearing formations. The microemulsions are driven toward at least one recovery well and crude petroleum is recovered through the recovery well. The LPG in the micellar system may be propane or butane. Corrosion inhibitors can be used in sour fields, and bactericides can be used where necessary. The microemulsions used contain up to about 10-20% water and about 8% surfactant. (4 claims)

Gogarty, W.B.; Olson, R.W.

1967-01-31T23:59:59.000Z

347

Optimization of Concurrent Deployments of the Juvenile Salmon Acoustic Telemetry System and Other Hydroacoustic Equipment at John Day Dam  

DOE Green Energy (OSTI)

The purpose of this report is to document the results of the acoustic optimization study conducted at John Day Dam during January and February 2008. The goal of the study was to optimize performance of the Juvenile Salmon Acoustic Telemetry System (JSATS) by determining deployment and data acquisition methods to minimize electrical and acoustic interference from various other acoustic sampling devices. Thereby, this would allow concurrent sampling by active and passive acoustic methods during the formal evaluations of the prototype surface flow outlets at the dam during spring and summer outmigration seasons for juvenile salmonids. The objectives for the optimization study at John Day Dam were to: 1. Design and test prototypes and provide a total needs list of pipes and trolleys to deploy JSATS hydrophones on the forebay face of the powerhouse and spillway. 2. Assess the effect on mean percentage decoded of JSATS transmissions from tags arrayed in the forebay and detected on the hydrophones by comparing: turbine unit OFF vs. ON; spill bay OPEN vs. CLOSED; dual frequency identification sonar (DIDSON) and acoustic Doppler current profiler (ADCP) both OFF vs. ON at a spill bay; and, fixed-aspect hydroacoustic system OFF vs. ON at a turbine unit and a spill bay. 3. Determine the relationship between fixed-aspect hydroacoustic transmit level and mean percentage of JSATS transmissions decoded. The general approach was to use hydrophones to listen for transmissions from JSATS tags deployed in vertical arrays in a series perpendicular to the face of the dam. We used acoustic telemetry equipment manufactured by Technologic and Sonic Concepts. In addition, we assessed old and new JSATS signal detectors and decoders and two different types of hydrophone baffling. The optimization study consisted of a suite of off/on tests. The primary response variable was mean percentage of tag transmissions decoded. We found that there was no appreciable adverse effect on mean percentage decoded for JSATS transmitters from: turbine operations; spillway operations; DIDSON/ADCP acoustic energy; and PAS hydroacoustic systems at transmit level of -12 dB, although there was a significant impact at all higher transmit levels (-11 to -6 dB). The main conclusion from this optimization study is that valid JSATS telemetry data can be collected simultaneously with a DIDSON/ADCP and a PAS hydroacoustic system at transmit level -12 dB. Multiple evaluation tools should be considered to increase the robustness and thoroughness of future fish passage evaluations at John Day and other dams.

Ploskey, Gene R.; Hughes, James S.; Khan, Fenton; Kim, Jina; Lamarche, Brian L.; Johnson, Gary E.; Choi, Eric Y.; Faber, Derrek M.; Wilberding, Matthew C.; Deng, Zhiqun; Weiland, Mark A.; Zimmerman, Shon A.; Fischer, Eric S.; Cushing, Aaron W.

2008-09-01T23:59:59.000Z

348

Information Resources: Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Tools Tools Below are links to tools that assist users with project planning and analysis. Residential Lighting Usage Estimate Tool The Residential Lighting Usage Estimate Tool is a companion to the report, "Residential Lighting End-Use Consumption Study," which developed a regional estimation framework within a national sample design that allows for the estimation of lamp usage and energy consumption. The tool contains the full set of estimates produced by methodology described in the study. Simple Modular LED Cost Model (LEDCOM) The LED Cost Model provides a simplified method for analyzing the manufacturing costs of an LED package, and enables those involved in the manufacture of LED packages to evaluate the relative impact of changes made at different points in the manufacturing process on the final LED package cost.

349

Recovery Act Funding Opportunity Announcement: Enhanced Geothermal...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here Home Recovery Act Funding Opportunity Announcement: Enhanced Geothermal Systems Component Research and DevelopmentAnalysis Recovery Act Funding Opportunity...

350

Optimize carbon dioxide sequestration, enhance oil recovery  

NLE Websites -- All DOE Office Websites (Extended Search)

4 January Optimize carbon dioxide sequestration, enhance oil recovery Optimize carbon dioxide sequestration, enhance oil recovery The simulation provides an important...

351

Optimize carbon dioxide sequestration, enhance oil recovery  

NLE Websites -- All DOE Office Websites (Extended Search)

Optimize carbon dioxide sequestration, enhance oil recovery Optimize carbon dioxide sequestration, enhance oil recovery The simulation provides an important approach to estimate...

352

Enhanced Oil Recovery | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

(or enhanced) recovery. During primary recovery, the natural pressure of the reservoir or gravity drive oil into the wellbore, combined with artificial lift techniques (such as...

353

Enhanced Oil Recovery | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Enhanced Oil Recovery Enhanced Oil Recovery Thanks in part to innovations supported by the Office of Fossil Energy's National Energy Technology Laboratory over the past 30 years,...

354

Some Thoughts on Econometric Information Recovery  

E-Print Network (OSTI)

Thoughts on Econometric Information Recovery George G. JudgeSome Thoughts on Econometric Information Recovery George G.G. Judge. ed. 2013. “An Information Theoretic Approach to

Judge, George G.

2013-01-01T23:59:59.000Z

355

Energy Recovery Inc | Open Energy Information  

Open Energy Info (EERE)

California . References "Energy Recovery Inc" Retrieved from "http:en.openei.orgwindex.php?titleEnergyRecoveryInc&oldid344878" Categories: Clean Energy Organizations...

356

Testing the effectiveness of an acoustic deterrent for gray whales along the Oregon coast  

SciTech Connect

This study was conducted to determine whether a low-powered sound source could be effective at deterring gray whales from areas that may prove harmful to them. With increased interest in the development of marine renewal energy along the Oregon coast the concern that such development may pose a collision or entanglement risk for gray whales. A successful acoustic deterrent could act as a mitigation tool to prevent harm to whales from such risks. In this study, an acoustic device was moored on the seafloor in the pathway of migrating gray whales off Yaquina Head on the central Oregon coast. Shore-based observers tracked whales with a theodolite (surveyor’s tool) to accurately locate whales as they passed the headland. Individual locations of different whales/whale groups as well as tracklines of the same whale/whale groups were obtained and compared between times with the acoustic device was transmitting and when it was off. Observations were conducted on 51 d between January 1 and April 15, 2012. A total of 143 individual whale locations were collected for a total of 243 whales, as well as 57 tracklines for a total of 142 whales. Inclement weather and equipment problems resulted in very small sample sizes, especially during experimental periods, when the device was transmitting. Because of this, the results of this study were inconclusive. We feel that another season of field testing is warranted to successfully test the effectiveness of the deterrent, but recommend increasing the zone of influence to 3 km to ensure the collection of adequate sample sizes. Steps have been taken to acquire the necessary federal research permit modification to authorize the increased zone of influence and to modify the acoustic device for the increased power. With these changes we are confident we will be able to determine whether the deterrent is effective at deflecting gray whales. A successful deterrent device may serve as a valuable mitigation tool to protect gray whales, and other baleen whales, in the event that marine energy development poses a collision or entanglement risk.

Lagerquist, Barbara [Oregon State University Marine Mammal Institute; Winsor, Martha [Oregon State University Marine Mammal Institute; Mate, Bruce [Oregon State University Marine Mammal Institute

2012-12-31T23:59:59.000Z

357

Renewable Energy Evaluation Tools  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

RENEWABLE ENERGY RENEWABLE ENERGY EVALUATION TOOLS Andy Walker, PhD PE Principal Engineer, NREL Renewable Energy Round Table May 2, 2012 2 TECHNICAL ASSESSMENT AND SCREENING TOOLS WE USE IN OUR PROJECTS Campus/Base Assessments INFRASTRUCTURE BUILDINGS ASSESSMENT RENEWABLE SUPPLY SIDE VEHICLES & TOOLS Campus/Base Assessments INFRASTRUCTURE BUILDINGS ASSESSMENT RENEWABLE SUPPLY SIDE VEHICLES & TOOLS 9 9 Renewable Energy Technologies Photovoltaics Daylighting Biomass Heat/Power Concentrating Solar Heat/Power Solar Vent Air Preheat Solar Water Heating Wind Power Ground Source Heat Pump Landfill Gas 10 10 Renewable Energy Resources Geographical Information System (GIS) Datasets * NREL Datasets (http://www.nrel.gov/gis/) - solar radiation 10x10 km grid

358

Strain gauge installation tool  

SciTech Connect

A tool and a method for attaching a strain gauge to a test specimen by maaining alignment of, and applying pressure to, the strain gauge during the bonding of the gauge to the specimen. The tool comprises rigid and compliant pads attached to a spring-loaded clamp. The pads are shaped to conform to the specimen surface to which the gauge is to be bonded. The shape of the pads permits the tool to align itself to the specimen and to maintain alignment of the gauge to the specimen during the bond curing process. A simplified method of attaching a strain gauge is provided by use of the tool.

Conard, Lisa Marie (Swissvale, PA)

1998-01-01T23:59:59.000Z

359

Risk Management Tool Attributes:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

- Tools & SMEs - Tools & SMEs Outline for Breakout Session TOOLS 1. Types of Tools a. Risk Management - Database & Reports, risk register, risk forms, risk tracking & monitoring, basis of estimate, action item tracking, historical record of risks & changes, configuration control, enterprise-wide, metrics, risk performance index, risk checklist, graphical display, management reporting (various levels), risk communications b. Risk Analysis i. Cost, ii. budgets, funding, cash-flow analysis, iii. Schedule iv. tailoring categories v. Integrated Cost & Schedule vi. Project phase analysis; organization ownership & joint planning c. Risk Knowledge and Lessons Learned Database i. Enterprise-wide ii. Job/owner-specific iii. Workshops - project specific, risk management,

360

Library Conversion Tool  

Science Conference Proceedings (OSTI)

Library Conversion Tool. ... The LIB2NIST mass spectral data conversion program consists of the following files (which are contained in a ZIP archive): ...

2013-06-24T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

HPC_Tools.pptx  

NLE Websites -- All DOE Office Websites (Extended Search)

debuggers - DDT - Totalview Tools Out of bounds reference in source code for program "flip" ... allocate(putseed(randomsize)) ... badindex randomsize+1...

362

Climate Suitability Tool Description  

Science Conference Proceedings (OSTI)

... The Climate Suitability Tool implements the method outlined in the following publications ... The analysis is based on a single-zone model of natural ...

363

Tools & Resources: Resource Directory  

NLE Websites -- All DOE Office Websites (Extended Search)

that reduce air emissions. Emissions & Generation Resource Integrated Database (eGRID) A tool that provides data on the environmental characteristics of almost all electric...

364

Tools & Resources: Webcasts  

NLE Websites -- All DOE Office Websites (Extended Search)

NCCC Teams to Execute Your Mission Workforce 04132011 PDF WMV PDF Marketing & Driving Demand: Social Media Tools & Strategies Driving Demand 01062011 PDF WMV PDF Home...

365

Double diameter boring tool  

DOE Patents (OSTI)

A boring tool and a method of operation are provided for boring two concentric holes of precision diameters and depths in a single operation. The boring tool includes an elongated tool body, a shank for attachment to a standard adjustable boring head which is used on a manual or numerical control milling machine and first and second diametrically opposed cutting edges formed for cutting in opposite directions. The diameter of the elongated tool body is substantially equal to the distance from the first cutting edge tip to the axis of rotation plus the distance from the second cutting edge tip to the axis of rotation. The axis of rotation of the tool is spaced from the tool centerline a distance substantially equal to one-half the distance from the second cutting edge tip to the axis of rotation minus one-half the distance from the first cutting edge tip to the axis of rotation. The method includes the step of inserting the boring tool into the boring head, adjusting the distance between the tool centerline and the tool axis of rotation as described above and boring the two concentric holes.

Ashbaugh, Fred N. (Belton, MO); Murry, Kenneth R. (Odessa, MO)

1988-12-27T23:59:59.000Z

366

Double diameter boring tool  

DOE Patents (OSTI)

A boring tool and a method of operation are provided for boring two concentric holes of precision diameters and depths in a single operation. The boring tool includes an elongated tool body, a shank for attachment to a standard adjustable boring head which is used on a manual or numerical control milling machine and first and second diametrically opposed cutting flutes formed for cutting in opposite directions. The diameter of the elongated tool body is substantially equal to the distance from the first flute tip to the axis of rotation plus the distance from the second flute tip to the axis of rotation. The axis of rotation of the tool is spaced from the tool centerline a distance substantially equal to one-half the distance from the second flute tip to the axis of rotation minus one-half the distance from the first flute tip to the axis of rotation. The method includes the step of inserting the boring tool into the boring head, adjusting the distance between the tool centerline and the tool axis of rotation as described above and boring the two concentric holes.

Ashbaugh, F.A.; Murry, K.R.

1986-02-10T23:59:59.000Z

367

Strain gauge installation tool  

DOE Patents (OSTI)

A tool and a method for attaching a strain gauge to a test specimen by maintaining alignment of, and applying pressure to, the strain gauge during the bonding of the gauge to the specimen. The tool comprises rigid and compliant pads attached to a spring-loaded clamp. The pads are shaped to conform to the specimen surface to which the gauge is to be bonded. The shape of the pads permits the tool to align itself to the specimen and to maintain alignment of the gauge to the specimen during the bond curing process. A simplified method of attaching a strain gauge is provided by use of the tool.

Conard, Lisa Marie

1997-12-01T23:59:59.000Z

368

ORISE: Training and Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Training and Tools Chronic diseases such as diabetes, heart disease and cancer afflict more people every year and have resulted in increased demand for trained health care...

369

High Performance Tooling Materials  

Science Conference Proceedings (OSTI)

High performance tools are necessary for the successful manufacturing of every consumer product as well as oil drilling and mining operations. Increasing ...

370

RMOTC - Testing - Enhanced Oil Recovery  

NLE Websites -- All DOE Office Websites (Extended Search)

Enhanced Oil Recovery Enhanced Oil Recovery Notice: As of July 15th 2013, the Department of Energy announced the intent to sell Naval Petroleum Reserve Number 3 (NPR3). The sale of NPR-3 will also include the sale of all equipment and materials onsite. A decision has been made by the Department of Energy to complete testing at RMOTC by July 1st, 2014. RMOTC will complete testing in the coming year with the currently scheduled testing partners. For more information on the sale of NPR-3 and sale of RMOTC equipment and materials please join our mailing list here. RMOTC will play a significant role in continued enhanced oil recovery (EOR) technology development and field demonstration. A scoping engineering study on Naval Petroleum Reserve No. 3's (NPR-3) enhanced oil recovery

371

Recovery Act State Memos Florida  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

October 1, 2010 October 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5 ELECTRIC GRID ........................................................................................................ 6 TRANSPORTATION ................................................................................................. 8 CARBON CAPTURE AND STORAGE ........................................................................ 9

372

Recovery Act State Memos Florida  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

June 1, 2010 June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5 ELECTRIC GRID ........................................................................................................ 8 TRANSPORTATION ............................................................................................... 10 CARBON CAPTURE AND STORAGE ...................................................................... 10

373

UML Fever: Diagnosis and Recovery  

Science Conference Proceedings (OSTI)

Acknowledgment is only the first step toward recovery from this potentially devastating affliction. The Institute of Infectious Diseases has recently published research confirming that the many and varied strains of UML Fever continue to spread ...

Alex E. Bell

2005-03-01T23:59:59.000Z

374

Outlook for enhanced oil recovery  

Science Conference Proceedings (OSTI)

This paper reviews the potential for enhanced oil recovery, the evolutionary nature of the recovery processes being applied in oilfields today, key parameters that describe the technology state-of-the-art for each of the major oil recovery processes, and the nature and key outputs from the current Department of Energy research program on enhanced oil recovery. From this overview, it will be seen that the DOE program is focused on the analysis of ongoing tests and on long-range, basic research to support a more thorough understanding of process performance. Data from the program will be made available through reports, symposia, and on-line computer access; the outputs are designed to allow an independent producer to evaluate his own project as an effort to transfer rapidly the technology now being developed.

Johnson, H.R.

1982-01-01T23:59:59.000Z

375

Self-adaptive methods for acoustic focusing and mode extraction in a shallow ocean waveguide  

E-Print Network (OSTI)

1.1 Time-reversal in the shallow ocean . . . . . .applications versus ocean acoustic SONAR and communicationsH. Schmidt, Computational Ocean Acoustics, (AIP New York,

Walker, Shane C.

2005-01-01T23:59:59.000Z

376

Spectrally efficient underwater acoustic communications : channel characterization and design aspects for OFDM  

E-Print Network (OSTI)

with L = 9 for an underwater channel impulse response with Ladaptive modulation in underwater acoustic communications,”Adaptive OFDM for underwater acoustic channels with limited

Radoševi?, Andreja

2012-01-01T23:59:59.000Z

377

Solid-State Lighting: Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

about Solid-State Lighting: Tools on Twitter Bookmark Solid-State Lighting: Tools on Google Bookmark Solid-State Lighting: Tools on Delicious Rank Solid-State Lighting: Tools on...

378

Disaster Resiliency and Recovery: Capabilities (Fact Sheet), NREL (National Renewable Energy Laboratory)  

NLE Websites -- All DOE Office Websites (Extended Search)

a a pa b i l i t i e s Disaster Resiliency and Recovery NREL Experts Assist Before and After a Disaster The National Renewable Energy Laboratory (NREL) is the nation's leader in energy efficient and renewable energy technologies, practices, and strategies. For the last 15 years, NREL has provided expertise, tools, and innovations to private industry; federal, state, and local governments; non-profit organizations; and communities during the planning, recovery,

379

Federal Energy Management Program: Recovery Act  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery Act to Recovery Act to someone by E-mail Share Federal Energy Management Program: Recovery Act on Facebook Tweet about Federal Energy Management Program: Recovery Act on Twitter Bookmark Federal Energy Management Program: Recovery Act on Google Bookmark Federal Energy Management Program: Recovery Act on Delicious Rank Federal Energy Management Program: Recovery Act on Digg Find More places to share Federal Energy Management Program: Recovery Act on AddThis.com... Energy Savings Performance Contracts ENABLE Utility Energy Service Contracts On-Site Renewable Power Purchase Agreements Energy Incentive Programs Recovery Act Technical Assistance Projects Project Stories Recovery Act The American Recovery and Reinvestment Act of 2009 included funding for the Federal Energy Management Program (FEMP) to facilitate the Federal

380

EMSL: Capabilities: American Recovery and Reinvestment Act  

NLE Websites -- All DOE Office Websites (Extended Search)

EMSL Procurements under Recovery Act EMSL Procurements under Recovery Act Additional Information Investing in Innovation: EMSL and the American Recovery and Reinvestment Act Recovery Act and Systems Biology at EMSL Recovery Act Instruments coming to EMSL In the News EMSL ARRA Capability Features News: Recovery Act and PNNL Recovery Act in the Tri-City Herald Related Links Recovery.gov DOE and the Recovery Act Message from Energy Secretary Chu Recovery Act at PNNL EMSL evolves with the needs of its scientific users, and the American Recovery and Reinvestment Act has helped to accelerate this evolution. Thirty-one instruments were acquired and installed at EMSL. These instruments are listed below, and each listing is accompanied by a brief overview. Each of these new and leading-edge instruments was chosen by design to

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Developing a Regional Recovery Framework  

Science Conference Proceedings (OSTI)

Abstract A biological attack would present an unprecedented challenge for local, state, and federal agencies; the military; the private sector; and individuals on many fronts ranging from vaccination and treatment to prioritization of cleanup actions to waste disposal. To prepare the Seattle region to recover from a biological attack, the Seattle Urban Area Security Initiative (UASI) partners collaborated with military and federal agencies to develop a Regional Recovery Framework for a Biological Attack in the Seattle Urban Area. The goal was to reduce the time and resources required to recover and restore wide urban areas, military installations, and other critical infrastructure following a biological incident by providing a coordinated systems approach. Based on discussions in small workshops, tabletop exercises, and interviews with emergency response agency staff, the partners identified concepts of operation for various areas to address critical issues the region will face as recovery progresses. Key to this recovery is the recovery of the economy. Although the Framework is specific to a catastrophic, wide-area biological attack using anthrax, it was designed to be flexible and scalable so it could also serve as the recovery framework for an all-hazards approach. The Framework also served to coalesce policy questions that must be addressed for long-term recovery. These questions cover such areas as safety and health, security, financial management, waste management, legal issues, and economic development.

Lesperance, Ann M.; Olson, Jarrod; Stein, Steven L.; Clark, Rebecca; Kelly, Heather; Sheline, Jim; Tietje, Grant; Williamson, Mark; Woodcock, Jody

2011-09-01T23:59:59.000Z

382

Mapping acoustic emissions from hydraulic fracture treatments using coherent array processing: Concept  

DOE Green Energy (OSTI)

Hydraulic fracturing is a widely-used well completion technique for enhancing the recovery of gas and oil in low-permeability formations. Hydraulic fracturing consists of pumping fluids into a well under high pressure (1000--5000 psi) to wedge-open and extend a fracture into the producing formation. The fracture acts as a conduit for gas and oil to flow back to the well, significantly increasing communication with larger volumes of the producing formation. A considerable amount of research has been conducted on the use of acoustic (microseismic) emission to delineate fracture growth. The use of transient signals to map the location of discrete sites of emission along fractures has been the focus of most research on methods for delineating fractures. These methods depend upon timing the arrival of compressional (P) or shear (S) waves from discrete fracturing events at one or more clamped geophones in the treatment well or in adjacent monitoring wells. Using a propagation model, the arrival times are used to estimate the distance from each sensor to the fracturing event. Coherent processing methods appear to have sufficient resolution in the 75 to 200 Hz band to delineate the extent of fractures induced by hydraulic fracturing. The medium velocity structure must be known with a 10% accuracy or better and no major discontinuities should be undetected. For best results, the receiving array must be positioned directly opposite the perforations (same depths) at a horizontal range of 200 to 400 feet from the region to be imaged. Sources of acoustic emission may be detectable down to a single-sensor SNR of 0.25 or somewhat less. These conclusions are limited by the assumptions of this study: good coupling to the formation, acoustic propagation, and accurate knowledge of the velocity structure.

Harris, D.B.; Sherwood, R.J.; Jarpe, S.P.; Harben, P.E.

1991-09-01T23:59:59.000Z

383

Acoustic analogues of black hole singularities  

SciTech Connect

We search for acoustic analogues of a spherical symmetric black hole with a pointlike source. We show that the gravitational system has a dynamical counterpart in the constrained, steady motion of a fluid with a planar source. The equations governing the dynamics of the gravitational system can be exactly mapped in those governing the motion of the fluid. The different meaning that singularities and sources have in fluid dynamics and in general relativity is also discussed. Whereas in the latter a pointlike source is always associated with a (curvature) singularity in the former the presence of sources does not necessarily imply divergences of the fields.

Cadoni, Mariano; Mignemi, Salvatore [Dipartimento di Fisica, Universita di Cagliari, and INFN, Sezione di Cagliari, Cittadella Universitaria 09042 Monserrato (Italy); Dipartimento di Matematica, Universita di Cagliari, viale Merello 92, 09123 Cagliari, Italy, and INFN, Sezione di Cagliari (Italy)

2005-10-15T23:59:59.000Z

384

Acoustic analogues of black hole singularities  

E-Print Network (OSTI)

We search for acoustic analogues of a spherical symmetric black hole with a pointlike source. We show that the gravitational system has a dynamical counterpart in the constrained, steady motion of a fluid with a planar source. The equations governing the dynamics of the gravitational system can be exactly mapped in those governing the motion of the fluid. The different meaning that singularities and sources have in fluid dynamics and in general relativity is also discussed. Whereas in the latter a pointlike source is always associated with a (curvature) singularity in the former the presence of sources does not necessarily imply divergences of the fields.

Mariano Cadoni; Salvatore Mignemi

2005-04-29T23:59:59.000Z

385

Energy flow in acoustic black holes  

SciTech Connect

We present the results of an analysis of superradiant energy flow due to scalar fields incident on an acoustic black hole. In addition to providing independent confirmation of the recent results in [E. Berti, V. Cardoso, and J. P. S. Lemos, Phys. Rev. D 70, 124006 (2004).], we determine in detail the profile of energy flow everywhere outside the horizon. We confirm explicitly that in a suitable frame the energy flow is inward at the horizon and outward at infinity, as expected on physical grounds.

Choy, K.; Kruk, T.; Carrington, M.E.; Fugleberg, T.; Zahn, J.; Kobes, R.; Kunstatter, G.; Pickering, D. [Department of Physics, Brandon University, Brandon, Manitoba, R7A 6A9 (Canada) and Winnipeg Institute for Theoretical Physics, Winnipeg, Manitoba (Canada); Department of Physics, University of Winnipeg, Winnipeg, Manitoba, R7A 6A9 (Canada) and Winnipeg Institute for Theoretical Physics, Winnipeg, Manitoba (Canada); Department of Mathematics, Brandon University, Brandon, Manitoba, R7A 6A9 (Canada)

2006-05-15T23:59:59.000Z

386

Underwater Acoustic Sensor Networks: Research Challenges  

E-Print Network (OSTI)

Underwater sensor nodes will find applications in oceanographic data collection, pollution monitoring, o#shore exploration, disaster prevention, assisted navigation and tactical surveillance applications. Moreover, unmanned or autonomous underwater vehicles (UUVs, AUVs), equipped with sensors, will enable the exploration of natural undersea resources and gathering of scientific data in collaborative monitoring missions. Underwater acoustic networking is the enabling technology for these applications. Underwater networks consist of a variable number of sensors and vehicles that are deployed to perform collaborative monitoring tasks over a given area.

Ian Akyildiz Dario; Ian F. Akyildiz; Dario Pompili; Tommaso Melodia

2005-01-01T23:59:59.000Z

387

Underwater Acoustic Sensor Networks: Research Challenges  

E-Print Network (OSTI)

Underwater sensor nodes will find applications in oceanographic data collection, pollution monitoring, o#shore exploration, disaster prevention, assisted navigation and tactical surveillance applications. Moreover, unmanned or autonomous underwater vehicles (UUVs, AUVs), equipped with sensors, will enable the exploration of natural undersea resources and gathering of scientific data in collaborative monitoring missions. Underwater acoustic networking is the enabling technology for these applications. Underwater networks consist of a variable number of sensors and vehicles that are deployed to perform collaborative monitoring tasks over a given area. In this

Ian F. Akyildiz; Dario Pompili; Tommaso Melodia

2005-01-01T23:59:59.000Z

388

Netcat Power Tools  

Science Conference Proceedings (OSTI)

Netcat in one of the most commonly used anti-hacking tools in the world. It reads and writes data across network connections, using the TCP/IP protocol. It is designed to be a reliable "back-end" tool that can be used directly or easily driven by other ... Keywords: Internet, Security

Jan Kanclirz, Jr.

2008-06-01T23:59:59.000Z

389

Fast LMS/Newton algorithms for stereophonic acoustic echo cancelation  

Science Conference Proceedings (OSTI)

This paper presents a new class of adaptive filtering algorithms to solve the stereophonic acoustic echo cancelation (AEC) problem in teleconferencing systems. While stereophonic AEC may be seen as a simple generalization of the well-known single-channel ... Keywords: LMS/Newton, adaptive filters, lattice orthogonalization, stereo acoustic echo cancellation (AEC)

Harsha I. K. Rao; Behrouz Farhang-Boroujeny

2009-08-01T23:59:59.000Z

390

Resonant acoustic transducer system for a well drilling string  

DOE Patents (OSTI)

For use in transmitting acoustic waves propated along a well drilling string, a piezoelectric transducer is provided operating in the relatively low loss acoustic propagation range of the well drilling string. The efficiently coupled transmitting transducer incorporates a mass-spring-piezoelectric transmitter combination permitting a resonant operation in the desired low frequency range.

Nardi, Anthony P. (Burlington, MA)

1981-01-01T23:59:59.000Z

391

Resonant acoustic transducer system for a well drilling string  

DOE Patents (OSTI)

For use in transmitting acoustic waves propagated along a well drilling string, a piezoelectric transducer is provided operating in the relatively low loss acoustic propagation range of the well drilling string. The efficiently coupled transmitting transducer incorporates a mass-spring-piezoelectric transmitter combination permitting resonant operation in the desired low frequency range.

Kent, William H. (Westford, MA); Mitchell, Peter G. (Concord, MA)

1981-01-01T23:59:59.000Z

392

Tomographic Maps of the Ocean Mesoscale. Part 1: Pure Acoustics  

Science Conference Proceedings (OSTI)

A field test of ocean acoustic tomography was conducted in 1981 for a two month period in a 300 km square at 26°N, 70°W in the North Atlantic (just south of the MODE region). Nine acoustic deep-sea moorings with sea floor transponders for ...

B. Cornuelle; C. Wunsch; D. Behringer; T. Birdsall; M. Brown; R. Heinmiller; R. Knox; K. Metzger; W. Munk; J. Spiesberger; R. Spindel; D. Webb; P. Worcester

1985-02-01T23:59:59.000Z

393

Focused beam routing protocol for underwater acoustic networks  

Science Conference Proceedings (OSTI)

Multi-hop transmission is considered for large coverage areas in bandwidth-limited underwater acoustic networks. In this paper, we present a scalable routing technique based on location information, and optimized for minimum energy per bit consumption. ... Keywords: power control, routing, underwater acoustic networks

Josep Miquel Jornet; Milica Stojanovic; Michele Zorzi

2008-09-01T23:59:59.000Z

394

Acoustic detection of partial discharges in insulation oil  

Science Conference Proceedings (OSTI)

In this paper, we performed an insulation diagnosis technique for oil-immersed power transformers by an acoustic detection method. Electrode system such as needle to plane electrode was fabricated to simulate a defect of power transformers. In addition, ... Keywords: acoustic detection, frequency component, insulation diagnostic, partial discharge, positioning

Dae-Won Park; Sang-Wook Cha; Gyung-Suk Kil

2011-03-01T23:59:59.000Z

395

Intelligent acoustic rotor speed estimation for an autonomous helicopter  

Science Conference Proceedings (OSTI)

Acoustic sensing to gather information about a machine can be highly beneficial, but processing the data can be difficult. In this work, a variety of methodologies have been studied to extract rotor speed information from the sound signature of an autonomous ... Keywords: Acoustic sensing, Adaptive network-based fuzzy inference system, Artificial neural network, Feature selection, Genetic algorithm, Helicopter, Rotor speeds

Benjamin N. Passow; Mario A. Gongora; Adrian A. Hopgood; Sophy Smith

2012-11-01T23:59:59.000Z

396

Acoustical Measurement of Current and Vorticity beneath Ice  

Science Conference Proceedings (OSTI)

An acoustical instrument has been developed to measure path-averaged horizontal current and vorticity in the subice boundary layer of the eastern Arctic during the spring of 1989. A triangular acoustic array of side 200 m was used to obtain ...

Dimitris Menemenlis; David M. Farmer

1992-12-01T23:59:59.000Z

397

ARM - Data Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

govDataData Tools govDataData Tools Data Tools Most ARM data is archived and made available as time-series data in netCDF format. NetCDF (designed by Unidata) is relatively compact, is appendable, is capable of storing descriptive "meta-data" along with measurement data, and is platform-independent. However, the organization of data within netCDF files tends to follow conventions reflecting either the source or the end use of the data. Consequently, tools developed for use with netCDF files following one convention may not be optimal for use with those following another convention. For example, tools designed for examination of geographically-gridded data may not be well-suited for analysis of time-series data such as that generated by ARM. In addition, some of the

398

OOTW Force Design Tools  

Science Conference Proceedings (OSTI)

This report documents refined requirements for tools to aid the process of force design in Operations Other Than War (OOTWs). It recommends actions for the creation of one tool and work on other tools relating to mission planning. It also identifies the governmental agencies and commands with interests in each tool, from whom should come the user advisory groups overseeing the respective tool development activities. The understanding of OOTWs and their analytical support requirements has matured to the point where action can be taken in three areas: force design, collaborative analysis, and impact analysis. While the nature of the action and the length of time before complete results can be expected depends on the area, in each case the action should begin immediately. Force design for OOTWs is not a technically difficult process. Like force design for combat operations, it is a process of matching the capabilities of forces against the specified and implied tasks of the operation, considering the constraints of logistics, transport and force availabilities. However, there is a critical difference that restricts the usefulness of combat force design tools for OOTWs: the combat tools are built to infer non-combat capability requirements from combat capability requirements and cannot reverse the direction of the inference, as is required for OOTWs. Recently, OOTWs have played a larger role in force assessment, system effectiveness and tradeoff analysis, and concept and doctrine development and analysis. In the first Quadrennial Defense Review (QDR), each of the Services created its own OOTW force design tool. Unfortunately, the tools address different parts of the problem and do not coordinate the use of competing capabilities. These tools satisfied the immediate requirements of the QDR, but do not provide a long-term cost-effective solution.

Bell, R.E.; Hartley, D.S.III; Packard, S.L.

1999-05-01T23:59:59.000Z

399

Borehole-Wall Imaging with Acoustic and Optical Televiewers for  

Open Energy Info (EERE)

Borehole-Wall Imaging with Acoustic and Optical Televiewers for Borehole-Wall Imaging with Acoustic and Optical Televiewers for Fractured-Bedrock Aquifer Investigations Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Borehole-Wall Imaging with Acoustic and Optical Televiewers for Fractured-Bedrock Aquifer Investigations Abstract Imaging with acoustic and optical televiewers results in continuous and oriented 360 degree views of the borehole wall from which the character and orientation of lithologic and structural features can be defined for fractured-bedrock aquifer investigations. Fractures are more clearly defined under a wider range of conditions on acoustic images than on optical images including dark-colored rocks, cloudy borehole water, and coated borehole walls. However, optical images allow for the direct viewing

400

Acoustic-velocity measurements in materials using a regenerative method  

DOE Patents (OSTI)

Acoustic energy is propatated through earth material between an electro-acoustic generator and a receiver which converts the received acoustic energy into electrical signals. A closed loop is formed by a variable gain amplifier system connected between the receiver and the generator. The gain of the amplifier system is increased until sustained oscillations are produced in the closed loop. The frequency of the oscillations is measured as an indication of the acoustic propagation velocity through the earth material. The amplifier gain is measured as an indication of the acoustic attenuation through the earth materials. The method is also applicable to the non-destructive testing of structural materials, such as steel, aluminum and concrete.

Laine, E.F.

1982-09-30T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Acoustic velocity measurements in materials using a regenerative method  

DOE Patents (OSTI)

Acoustic energy is propagated through earth material between an electro-acoustic generator and a receiver which converts the received acoustic energy into electrical signals. A closed loop is formed by a variable gain amplifier system connected between the receiver and the generator. The gain of the amplifier system is increased until sustained oscillations are produced in the closed loop. The frequency of the oscillations is measured as an indication of the acoustic propagation velocity through the earth material. The amplifier gain is measured as an indication of the acoustic attenuation through the earth materials. The method is also applicable to the non-destructive testing of structural materials, such as steel, aluminum and concrete.

Laine, Edwin F. (Alamo, CA)

1986-01-01T23:59:59.000Z

402

Recovery Act Measurement Science and Engineering ...  

Science Conference Proceedings (OSTI)

*. Bookmark and Share. Recovery Act Measurement Science and Engineering Fellowship Program. Grants.gov Synopsis. ...

2013-03-15T23:59:59.000Z

403

Weatherization and Intergovernmental Program: Recovery Act  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery Act to someone by E-mail Share Weatherization and Intergovernmental Program: Recovery Act on Facebook Tweet about Weatherization and Intergovernmental Program: Recovery Act on Twitter Bookmark Weatherization and Intergovernmental Program: Recovery Act on Google Bookmark Weatherization and Intergovernmental Program: Recovery Act on Delicious Rank Weatherization and Intergovernmental Program: Recovery Act on Digg Find More places to share Weatherization and Intergovernmental Program: Recovery Act on AddThis.com... Plans, Implementation, & Results Weatherization Assistance Program WAP - Sustainable Energy Resources for Consumers Grants WAP - Weatherization Innovation Pilot Program State Energy Program Energy Efficiency & Conservation Block Grant Program

404

Opto-acoustic transducer for medical applications  

DOE Patents (OSTI)

This invention is an optically activated transducer for generating acoustic vibrations in a biological medium. The transducer is located at the end of a fiber optic which may be located within a catheter. Energy for operating the transducer is provided optically by laser light transmitted through the fiber optic to the transducer. Pulsed laser light is absorbed in the working fluid of the transducer to generate a thermal pressure and consequent adiabatic expansion of the transducer head such that it does work against the ambient medium. The transducer returns to its original state by a process of thermal cooling. The motion of the transducer within the ambient medium couples acoustic energy into the medium. By pulsing the laser at a high repetition rate (which may vary from CW to 100 kHz) an ultrasonic radiation field can be established locally in the medium. This method of producing ultrasonic vibrations can be used in vivo for the treatment of stroke-related conditions in humans, particularly for dissolving thrombus. The catheter may also incorporate anti-thrombolytic drug treatments as an adjunct therapy and it may be operated in conjunction with ultrasonic detection equipment for imaging and feedback control.

Benett, William (Livermore, CA); Celliers, Peter (Berkeley, CA); Da Silva, Luiz (Danville, CA); Glinsky, Michael (Livermore, CA); London, Richard (Orinda, CA); Maitland, Duncan (Livermore, CA); Matthews, Dennis (Moss Beach, CA); Krulevich, Peter (Pleasanton, CA); Lee, Abraham (Walnut Creek, CA)

1999-01-01T23:59:59.000Z

405

Opto-acoustic transducer for medical applications  

DOE Patents (OSTI)

This invention is an optically activated transducer for generating acoustic vibrations in a biological medium. The transducer is located at the end of a fiber optic which may be located within a catheter. Energy for operating the transducer is provided optically by laser light transmitted through the fiber optic to the transducer. Pulsed laser light is absorbed in the working fluid of the transducer to generate a thermal pressure and consequent adiabatic expansion of the transducer head such that it does work against the ambient medium. The transducer returns to its original state by a process of thermal cooling. The motion of the transducer within the ambient medium couples acoustic energy into the medium. By pulsing the laser at a high repetition rate (which may vary from CW to 100 kHz) an ultrasonic radiation field can be established locally in the medium. This method of producing ultrasonic vibrations can be used in vivo for the treatment of stroke-related conditions in humans, particularly for dissolving thrombus. The catheter may also incorporate anti-thrombolytic drug treatments as an adjunct therapy and it may be operated in conjunction with ultrasonic detection equipment for imaging and feedback control.

Benett, William (Livermore, CA); Celliers, Peter (Berkeley, CA); Da Silva, Luiz (Danville, CA); Glinsky, Michael (Livermore, CA); London, Richard (Orinda, CA); Maitland, Duncan (Livermore, CA); Matthews, Dennis (Moss Beach, CA); Krulevich, Peter (Pleasanton, CA); Lee, Abraham (Walnut Creek, CA)

2002-01-01T23:59:59.000Z

406

Opto-acoustic transducer for medical applications  

Science Conference Proceedings (OSTI)

This invention is an optically activated transducer for generating acoustic vibrations in a biological medium. The transducer is located at the end of a fiber optic which may be located within a catheter. Energy for operating the transducer is provided optically by laser light transmitted through the fiber optic to the transducer. Pulsed laser light is absorbed in the working fluid of the transducer to generate a thermal pressure and consequent adiabatic expansion of the transducer head such that it does work against the ambient medium. The transducer returns to its original state by a process of thermal cooling. The motion of the transducer within the ambient medium couples acoustic energy into the medium. By pulsing the laser at a high repetition rate (which may vary from CW to 100 kHz) an ultrasonic radiation field can be established locally in the medium. This method of producing ultrasonic vibrations can be used in vivo for the treatment of stroke-related conditions in humans, particularly for dissolving thrombus. The catheter may also incorporate anti-thrombolytic drug treatments as an adjunct therapy and it may be operated in conjunction with ultrasonic detection equipment for imaging and feedback control. 7 figs.

Benett, W.; Celliers, P.; Da Silva, L.; Glinsky, M.; London, R.; Maitland, D.; Matthews, D.; Krulevich, P.; Lee, A.

1999-08-31T23:59:59.000Z

407

Development of critical surface diagnostic based on the ion acoustic decay instability in laser produced high density plasma  

SciTech Connect

We have developed a large angle, UV collective Thomson scattering (CTS) diagnostic for high density, hot plasma relevant to laser fusion. The CTS measured the basic parameters of the plasma waves (frequency, wave number), or the spectral density function for selected wave vectors of plasma waves, which were excited by the IADI (ion acoustic parametric decay instability). It is a good diagnostic tool for a local electron temperature measurement. The electron temperature was estimated by measuring either ion acoustic wave or electron plasma wave in the laser intensity window of 1

Mizuno, K.; DeGroot, J.S.; Drake, R.P.; Seka, W.; Craxton, R.S.; Estabrook, K.G.

1994-12-31T23:59:59.000Z

408

Vehicle Technologies Office: Recovery Act Funding Opportunities  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery Act Funding Recovery Act Funding Opportunities to someone by E-mail Share Vehicle Technologies Office: Recovery Act Funding Opportunities on Facebook Tweet about Vehicle Technologies Office: Recovery Act Funding Opportunities on Twitter Bookmark Vehicle Technologies Office: Recovery Act Funding Opportunities on Google Bookmark Vehicle Technologies Office: Recovery Act Funding Opportunities on Delicious Rank Vehicle Technologies Office: Recovery Act Funding Opportunities on Digg Find More places to share Vehicle Technologies Office: Recovery Act Funding Opportunities on AddThis.com... Recovery Act Funding Opportunities President Barack Obama announced on March 19 that the DOE is offering up to $2.4 billion in American Recovery and Reinvestment Act funds to support next-generation plug-in hybrid electric vehicles (PHEV) and their advanced

409

Partial Recovery of Quantum Entanglement  

E-Print Network (OSTI)

Suppose Alice and Bob try to transform an entangled state shared between them into another one by local operations and classical communications. Then in general a certain amount of entanglement contained in the initial state will decrease in the process of transformation. However, an interesting phenomenon called partial entanglement recovery shows that it is possible to recover some amount of entanglement by adding another entangled state and transforming the two entangled states collectively. In this paper we are mainly concerned with the feasibility of partial entanglement recovery. The basic problem we address is whether a given state is useful in recovering entanglement lost in a specified transformation. In the case where the source and target states of the original transformation satisfy the strict majorization relation, a necessary and sufficient condition for partial entanglement recovery is obtained. For the general case we give two sufficient conditions. We also give an efficient algorithm for the feasibility of partial entanglement recovery in polynomial time. As applications, we establish some interesting connections between partial entanglement recovery and the generation of maximally entangled states, quantum catalysis, mutual catalysis, and multiple-copy entanglement transformation.

Runyao Duan; Yuan Feng; Mingsheng Ying

2004-04-07T23:59:59.000Z

410

Graphitic packing removal tool  

DOE Patents (OSTI)

Graphitic packing removal tools are described for removal of the seal rings in one piece from valves and pumps. The packing removal tool has a cylindrical base ring the same size as the packing ring with a surface finish, perforations, knurling or threads for adhesion to the seal ring. Elongated leg shanks are mounted axially along the circumferential center. A slit or slits permit insertion around shafts. A removal tool follower stabilizes the upper portion of the legs to allow a spanner wrench to be used for insertion and removal.

Meyers, K.E.; Kolsun, G.J.

1996-12-31T23:59:59.000Z

411

ENERGY RECOVERY COUNCIL WEEKLY UPDATE  

E-Print Network (OSTI)

. Anaerobic digestion produces two main products, biogas and a soil amendment. Biogas can be used, food waste collection programs, biogas usage for energy, available EPA resources and tools

Columbia University

412

Microsoft Word - Recovery Act Cover  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Inspector General Inspector General Office of Audit Services Audit Report Decommissioning and Demolition Activities at Office of Science Sites OAS-RA-L-10-05 August 2010 DOE F 1325.8 (08-93) United States Government Department of Energy Memorandum DATE: August 12, 2010 Audit Report Number: OAS-RA-L-10-05 REPLY TO ATTN OF: IG-32 (A10RA005) SUBJECT: Audit Report on "Decommissioning and Demolition Activities at Office of Science Sites" TO: Deputy Director for Field Operations, SC-3 Manager, Brookhaven Site Office Manager, Argonne Site Office INTRODUCTION AND OBJECTIVE In February 2009, the President signed the American Recovery and Reinvestment Act of 2009 (Recovery Act) into law. The Department of Energy's (Department) Office of Environmental Management (EM) allocated $140 million of Recovery Act funds to

413

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

69.2 Million in 69.2 Million in Weatherization Funding and Energy Efficiency Grants for Maine Part of nearly $8 billion in Recovery Act funding for energy efficiency efforts nationwide that will create 100,000 jobs and cut energy bills for families March 12, 2009 Obama-Biden Administration Announces More Than $94.7 Million in Weatherization Funding and Energy Efficiency Grants for Kansas Part of nearly $8 billion in Recovery Act funding for energy efficiency efforts nationwide that will create 100,000 jobs and cut energy bills for families March 12, 2009 Obama-Biden Administration Announces More Than $121.3 Million in Weatherization Funding and Energy Efficiency Grants for Iowa Part of nearly $8 billion in Recovery Act funding for energy efficiency efforts nationwide that will create 100,000 jobs and cut energy bills for

414

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

August 12, 2010 August 12, 2010 Department of Energy Paves Way for Additional Clean Energy Projects and Jobs Through Manufacturing Solicitation Recovery Act Funds to Support New Renewable Energy Manufacturing Projects August 2, 2010 Department of Energy Announces $188 Million for Small Business Technology Commercialization Includes $73 million in Recovery Act Investments to Help Small Businesses Bring Clean Energy Ideas to the Marketplace July 22, 2010 Secretary Chu Announces Six Projects to Convert Captured CO2 Emissions from Industrial Sources into Useful Products $106 Million Recovery Act Investment will Reduce CO2 Emissions and Mitigate Climate Change July 21, 2010 DOE Hosts Workshop on Transition to Electric Vehicles Washington, DC - On Thursday, July 22, 2010, the Department of Energy will

415

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

June 18, 2010 June 18, 2010 Energetx Composites was able to purchase equipment such as this mold for utility-scale wind turbine blades thanks to a Recovery Act grant that matched the company's $3.5 million investment. | Photo Courtesy of Energetx | VP 100: Retooling Michigan -- Yachts and Watts Tiara Yachts makes fiber composite structures for boats. Now the Holland, Mich.-based company is transforming part of its factory and using its 30 years of expertise in composites to establish a new company - Energetx Composites - that will produce commercial-sized wind turbine blades. June 18, 2010 Five More States Reach Major Recovery Act Weatherization Milestone Minnesota, Montana, New Hampshire, New Mexico, and Utah Have Weatherized Over 9,000 Homes with Recovery Act Funding

416

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

12, 2009 12, 2009 Obama-Biden Administration Announces More Than $89.8 Million in Weatherization Funding and Energy Efficiency Grants for Mississippi Part of nearly $8 billion in Recovery Act funding for energy efficiency efforts nationwide that will create 100,000 jobs and cut energy bills for families March 12, 2009 Obama-Biden Administration Announces More Than $122.3 Million in Weatherization Funding and Energy Efficiency Grants for Louisiana Part of nearly $8 billion in Recovery Act funding for energy efficiency efforts nationwide that will create 100,000 jobs and cut energy bills for families March 12, 2009 Obama-Biden Administration Announces More Than $123.4 Million in Weatherization Funding and Energy Efficiency Grants for Kentucky Part of nearly $8 billion in Recovery Act funding for energy efficiency

417

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Nearly $80.7 Million in Weatherization Nearly $80.7 Million in Weatherization Funding and Energy Efficiency Grants for Oregon Part of nearly $8 billion in Recovery Act funding for energy efficiency efforts nationwide that will create 100,000 jobs and cut energy bills for families March 12, 2009 Obama-Biden Administration Announces More Than $107.6 Million in Weatherization Funding and Energy Efficiency Grants for Oklahoma Part of nearly $8 billion in Recovery Act funding for energy efficiency efforts nationwide that will create 100,000 jobs and cut energy bills for families March 12, 2009 Obama-Biden Administration Announces More Than $362.8 Million in Weatherization Funding and Energy Efficiency Grants for Ohio Part of nearly $8 billion in Recovery Act funding for energy efficiency efforts nationwide that will create 100,000 jobs and cut energy bills for

418

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9, 2010 9, 2010 AcuTemp received a $900,000 48C manufacturing tax credit under the American Recovery and Reinvestment Act to increase production of the company's ThermoCor vacuum insulation panels for more efficient ENERGY STAR appliances. | Photo courtesy of AcuTemp | AcuTemp Expands as Appliances Become More Energy Efficient AcuTemp, a small U.S. company that manufactures vacuum insulation panels that are needed to maintain precise temperatures for cold-storage products, is expanding and creating jobs in Dayton, OH thanks in part to the Recovery Act. August 6, 2010 A $20 million Recovery Act award will help Solazyme take production from tens of thousands of gallons a year of its algae "drop-in" oil to an annual production capacity of over half a million gallons. | Photo courtesy of Solazyme, Inc. |

419

Heat Recovery in Building Envelopes  

SciTech Connect

Infiltration has traditionally been assumed to contribute to the energy load of a building by an amount equal to the product of the infiltration flow rate and the enthalpy difference between inside and outside. Application of such a simple formula may produce an unreasonably high contribution because of heat recovery within the building envelope. Previous laboratory and simulation research has indicated that such heat transfer between the infiltrating air and walls may be substantial. In this study, Computational Fluid Dynamics was used to simulate sensible heat transfer in typical envelope constructions. The results show that the traditional method may over-predict the infiltration energy load by up to 95 percent at low leakage rates. A simplified physical model has been developed and used to predict the infiltration heat recovery based on the Peclet number of the flow and the fraction of the building envelope active in infiltration heat recovery.

Sherman, Max H.; Walker, Iain S.

2001-01-01T23:59:59.000Z

420

Python Tools at NERSC  

NLE Websites -- All DOE Office Websites (Extended Search)

Python Tools Python Tools Python Tools Description and Overview Python is an interpreted, general-purpose high-level programming language. Various of versions of Python are installed on most of the NERSC systems, usually accompanied with computational tool such as numpy and scipy. Using Python on NERSC Systems To use the python installed as module on NERSC systems, you need do module load python To run a python script on the Hopper and Edison compute nodes, you must set an environment variable: setenv CRAY_ROOTFS DSL which is set automatically when the python module is loaded. To execute a script on the Hopper or Edison compute nodes dedicated to your job, you need to use aprun: aprun -n 1 python ./hello_world.py or, if the script is executable and contains '#!/usr/bin/env python' as the

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Feature - WATER Tool Released  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Assessment for Transportation Energy Resources (WATER) Tool Released Water Assessment for Transportation Energy Resources (WATER) Tool Released Argonne National Laboratory recently released an open access online tool called WATER (Water Assessment for Transportation Energy Resources), which quantifies water footprint of fuel production stages from feedstock production to conversion process for biofuel with county, state, and regional level spatial resolution. WATER provides analysis on water consumption and its impact on water quality. It contains biofuel pathways for corn grain ethanol, soybean biodiesel, and cellulosic ethanol produced from corn stover and wheat straw. Perennial grass (Switchgrass and Miscanthus) and forest wood residue-based biofuel pathways are currently under development. The WATER tool enables users to conduct pathway comparison, scenario development, and regional specific feedstock analysis in supporting of biofuel industry development and planning. It is available at http://water.es.anl.gov/.

422

Friction stir welding tool  

DOE Patents (OSTI)

A friction stir welding tool is described and which includes a shank portion; a shoulder portion which is releasably engageable with the shank portion; and a pin which is releasably engageable with the shoulder portion.

Tolle; Charles R. (Idaho Falls, ID), Clark; Denis E. (Idaho Falls, ID), Barnes; Timothy A. (Ammon, ID)

2008-04-15T23:59:59.000Z

423

Smart tool holder  

SciTech Connect

There is provided an apparatus for machining surfaces to accuracies within the nanometer range by use of electrical current flow through the contact of the cutting tool with the workpiece as a feedback signal to control depth of cut.

Day, Robert Dean (Los Alamos, NM); Foreman, Larry R. (Los Alamos, NM); Hatch, Douglas J. (Los Alamos, NM); Meadows, Mark S. (Boston, MA)

1998-01-01T23:59:59.000Z

424

Tools for the Mentor  

Energy.gov (U.S. Department of Energy (DOE))

Here you will find a collection of tools and information to help you prepare to become and effective Mentor. Your primary goal is to use your knowledge, skills, and experience in assisting your...

425

Tools for the Mentee  

Energy.gov (U.S. Department of Energy (DOE))

The tools within this document will help to prepare you to become an effective Mentee and provide you with information on how to benefit from your Mentee-Mentor partnership.  The most important...

426

DAAC Data Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

WebGIS WebGIS is an Internet based technology that enables users to browse, query, and display spatial data using a standard web browser. Tool Link Help Point Gridded...

427

Strain gauge installation tool  

DOE Patents (OSTI)

A tool and a method are disclosed for attaching a strain gauge to a test specimen by maintaining alignment of, and applying pressure to, the strain gauge during the bonding of the gauge to the specimen. The tool comprises rigid and compliant pads attached to a spring-loaded clamp. The pads are shaped to conform to the specimen surface to which the gauge is to be bonded. The shape of the pads permits the tool to align itself to the specimen and to maintain alignment of the gauge to the specimen during the bond curing process. A simplified method of attaching a strain gauge is provided by use of the tool. 6 figs.

Conard, L.M.

1998-06-16T23:59:59.000Z

428

Acoustic Energy: An Innovative Technology for Stimulating Oil Wells  

Science Conference Proceedings (OSTI)

The objective of this investigation was to demonstrate the effectiveness of sonication in reducing the viscosity of heavy crude oils. Sonication is the use of acoustic or sound energy to produce physical and/or chemical changes in materials, usually fluids. The goal of the first project phase was to demonstrate a proof of concept for the project objective. Batch tests of three commercially available, single-weight oils (30-, 90-, and 120-wt) were performed in the laboratory. Several observations and conclusions were made from this series of experiments. These include the following: (1) In general, the lower the acoustic frequency, the greater the efficiency in reducing the viscosity of the oils; (2) Sonication treatment of the three oils resulted in reductions in viscosity that ranged from a low of 31% to a high of 75%; and (3) The results of the first phase of the project successfully demonstrated that sonication could reduce the viscosity of oils of differing viscosity. The goal of the second project phase was to demonstrate the ability of sonication to reduce the viscosity of three crude oils ranging from a light crude to a heavy crude. The experiments also were designed to examine the benefits of two proprietary chemical additives used in conjunction with sonication. Acoustic frequencies ranging from 800 Hz to 1.6 kHz were used in these tests, and a reactor chamber was designed for flow-through operation with a capacity of one gallon (3.8 liters). The three crude oils selected for use in the testing program were: (1) a heavy crude from California with a viscosity of approximately 65,000 cP (API gravity about 12{sup o}), (2) a crude from Alabama with a significant water content and a viscosity of approximately 6,000 cP (API gravity about 22 {sup o}), and (3) a light crude from the Middle East with a viscosity of approximately 700 cP (API gravity about 32{sup o}). The principal conclusions derived from the second project phase include the following: (1) The application of acoustic energy (sonication) significantly reduced the viscosity of crude oils, and the amount of viscosity reduction resulting is greater for more viscous, heavy crude oils than it is for less viscous, light crude oils. (2) Test results showed that after being heated, resulting viscosity reductions were not sustained following treatment to the extent that post-sonication reductions were sustained. (3) The maximum viscosity reductions in Oils 1, 2, and 3 due to sonication were 43%, 76%, and 6%, respectively. Samples of Oil 2 associated with larger viscosity reductions often exhibited a definite water separation layer follow the tests, whereas reductions of approximately 23% were measured when this separation was not observed. (4) It was observed that neither horn design nor the reduction of input power by 25% had very little effect on the ability of sonication to alter crude oil viscosity. (5) The chemical additives produced a range of viscosity reduction from 37% to a maximum of 94% with the largest reductions being facilitated by the abundant water present Oil 2. If the Oil 2 results are not considered, the maximum reduction was 73%. The effects of the additives and sonication are enhanced by each other. (6) In only one test did the viscosity return to as much as 50% of the pre-treatment value during a period of 30 days following treatment; recovery was much less in all other cases. Therefore, more than half of the viscosity reduction was maintained for a month without additional treatment. (7) Possible applications, market potential, and economic value of the implementation of a mature sonication technology within the petroleum industry were identified, and it was estimated that the potential exists that more than a billion barrels of oil could be upgraded or produced annually as a result. The project results successfully demonstrated that sonication alone and in combination with chemical additives can effectively reduce the viscosity of crude oils having a broad range of viscosity/API gravity values. Several recommendations are made for follow-on

Edgar, Dorland E.; Peters, Robert W.; Johnson, Donald O.; Paulsen, P. David; Roberts, Wayne

2006-04-30T23:59:59.000Z

429

Acoustic Energy: An Innovative Technology for Stimulating Oil Wells  

SciTech Connect

The objective of this investigation was to demonstrate the effectiveness of sonication in reducing the viscosity of heavy crude oils. Sonication is the use of acoustic or sound energy to produce physical and/or chemical changes in materials, usually fluids. The goal of the first project phase was to demonstrate a proof of concept for the project objective. Batch tests of three commercially available, single-weight oils (30-, 90-, and 120-wt) were performed in the laboratory. Several observations and conclusions were made from this series of experiments. These include the following: (1) In general, the lower the acoustic frequency, the greater the efficiency in reducing the viscosity of the oils; (2) Sonication treatment of the three oils resulted in reductions in viscosity that ranged from a low of 31% to a high of 75%; and (3) The results of the first phase of the project successfully demonstrated that sonication could reduce the viscosity of oils of differing viscosity. The goal of the second project phase was to demonstrate the ability of sonication to reduce the viscosity of three crude oils ranging from a light crude to a heavy crude. The experiments also were designed to examine the benefits of two proprietary chemical additives used in conjunction with sonication. Acoustic frequencies ranging from 800 Hz to 1.6 kHz were used in these tests, and a reactor chamber was designed for flow-through operation with a capacity of one gallon (3.8 liters). The three crude oils selected for use in the testing program were: (1) a heavy crude from California with a viscosity of approximately 65,000 cP (API gravity about 12{sup o}), (2) a crude from Alabama with a significant water content and a viscosity of approximately 6,000 cP (API gravity about 22 {sup o}), and (3) a light crude from the Middle East with a viscosity of approximately 700 cP (API gravity about 32{sup o}). The principal conclusions derived from the second project phase include the following: (1) The application of acoustic energy (sonication) significantly reduced the viscosity of crude oils, and the amount of viscosity reduction resulting is greater for more viscous, heavy crude oils than it is for less viscous, light crude oils. (2) Test results showed that after being heated, resulting viscosity reductions were not sustained following treatment to the extent that post-sonication reductions were sustained. (3) The maximum viscosity reductions in Oils 1, 2, and 3 due to sonication were 43%, 76%, and 6%, respectively. Samples of Oil 2 associated with larger viscosity reductions often exhibited a definite water separation layer follow the tests, whereas reductions of approximately 23% were measured when this separation was not observed. (4) It was observed that neither horn design nor the reduction of input power by 25% had very little effect on the ability of sonication to alter crude oil viscosity. (5) The chemical additives produced a range of viscosity reduction from 37% to a maximum of 94% with the largest reductions being facilitated by the abundant water present Oil 2. If the Oil 2 results are not considered, the maximum reduction was 73%. The effects of the additives and sonication are enhanced by each other. (6) In only one test did the viscosity return to as much as 50% of the pre-treatment value during a period of 30 days following treatment; recovery was much less in all other cases. Therefore, more than half of the viscosity reduction was maintained for a month without additional treatment. (7) Possible applications, market potential, and economic value of the implementation of a mature sonication technology within the petroleum industry were identified, and it was estimated that the potential exists that more than a billion barrels of oil could be upgraded or produced annually as a result. The project results successfully demonstrated that sonication alone and in combination with chemical additives can effectively reduce the viscosity of crude oils having a broad range of viscosity/API gravity values. Several recommendations are made for follow-on

Edgar, Dorland E.; Peters, Robert W.; Johnson, Donald O.; Paulsen, P. David; Roberts, Wayne

2006-04-30T23:59:59.000Z

430

Droplet Combustion and Non-Reactive Shear-Coaxial Jets with Transverse Acoustic Excitation  

E-Print Network (OSTI)

Related Works in Droplet Combustion . . . . . . . .of Acoustics on Droplet Combustion . . . . . . . . . . . .Fuel Droplet Combustion . . . . . . . . . . . . . . .

Teshome, Sophonias

2012-01-01T23:59:59.000Z

431

Passive acoustic fetal heart rate monitoring with a parallel redundance approach  

Science Conference Proceedings (OSTI)

Acoustic methods for monitoring fetal heart rate are potentially advantageous over ultrasound methods

Stephen A. Zahorian; Zongyao Zhou; Charles Brewton

1995-01-01T23:59:59.000Z

432

A Numerical Study on the Enhancement of Heat Transfer by Pressure Distributions in Acoustic Fields  

Science Conference Proceedings (OSTI)

The enhancement of heat transfer in a cavity was investigated in the absence of and in the presence of acoustic streaming induced by ultrasonic waves. The present study provides the experimental and numerical results of heat transfer in the acoustic ... Keywords: Acoustic pressure, Acoustic streaming, Coupled FE-BEM, Particle imaging velocimetry (PIV), Ultrasonic wave

Y. K. Oh; H. D. Yang

2005-01-01T23:59:59.000Z

433

Microbiology for enhanced oil recovery  

Science Conference Proceedings (OSTI)

The U. S. Department of Energy has sponsored several projects to investigate the feasibility of using microorganisms to enhance oil recovery. Microbes from the Wilmington oilfield, California, were found to be stimulated in growth by polyacrylamide mobility-control polymers and the microbes also can reduce the viscosity of the polyacrylamide solutions. Microbes have been discovered that produce surface active molecules, and several mixed cultures have been developed that make low viscosity, non-wetting, emulsions of heavy oils (/sup 0/API oil deposits, in China for enhanced recovery of light oils and successful field tests have been conducted in Romania and Arkansas.

Donaldson, E.C.

1983-06-01T23:59:59.000Z

434

SURFACTANT BASED ENHANCED OIL RECOVERY AND FOAM MOBILITY CONTROL  

Science Conference Proceedings (OSTI)

Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactants makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. Also, the addition of an alkali such as sodium carbonate makes possible in situ generation of surfactant and significant reduction of surfactant adsorption. In addition to reduction of interfacial tension to ultra-low values, surfactants and alkali can be designed to alter wettability to enhance oil recovery. An alkaline surfactant process is designed to enhance spontaneous imbibition in fractured, oil-wet, carbonate formations. It is able to recover oil from dolomite core samples from which there was no oil recovery when placed in formation brine. Mobility control is essential for surfactant EOR. Foam is evaluted to improve the sweep efficiency of surfactant injected into fractured reservoirs. UTCHEM is a reservoir simulator specially designed for surfactant EOR. A dual-porosity version is demonstrated as a potential scale-up tool for fractured reservoirs.

George J. Hirasaki; Clarence A. Miller; Gary A. Pope; Richard E. Jackson

2004-07-01T23:59:59.000Z

435

Why packages? The Windows tools  

E-Print Network (OSTI)

Why packages? The Windows tools A sample package Going further Package Development in Windows from August 13, 2008; updated November 23, 2012 1 of 45 #12;Why packages? The Windows tools A sample of packages 2 The Windows tools The main tools Missing pieces Installing the tools 3 A sample package Getting

Murdoch, Duncan

436

Building Energy Software Tools Directory: HVAC Residential Load...  

NLE Websites -- All DOE Office Websites (Extended Search)

New Tools DOE Sponsored Tools Submit a Tool Disclaimer Tools by Subject Tools Listed Alphabetically Tools by Platform...

437

Raising Photoemission Efficiency with Surface Acoustic Waves  

Science Conference Proceedings (OSTI)

We are developing a novel technique that may help increase the efficiency and reduce costs of photoelectron sources used at electron accelerators. The technique is based on the use of Surface Acoustic Waves (SAW) in piezoelectric materials, such as GaAs, that are commonly used as photocathodes. Piezoelectric fields produced by the traveling SAW spatially separate electrons and holes, reducing their probability of recombination, thereby enhancing the photoemission quantum efficiency of the photocathode. Additional advantages could be increased polarization provided by the enhanced mobility of charge carriers that can be controlled by the SAW and the ionization of optically-generated excitons resulting in the creation of additional electron-hole pairs. It is expected that these novel features will reduce the cost of accelerator operation. A theoretical model for photoemission in the presence of SAW has been developed, and experimental tests of the technique are underway.

A. Afanasev, F. Hassani, C.E. Korman, V.G. Dudnikov, R.P. Johnson, M. Poelker, K.E.L. Surles-Law

2012-07-01T23:59:59.000Z

438

Acoustic Timing Simulation of Active Beacons for  

E-Print Network (OSTI)

A simulation of freely-deployed active underwater beacons to estimate the tow path of a Synthetic Aperture Sonar (SAS) towfish is presented. Knowledge of the tow path allows the removal of motion induced blurring in the SAS images. The beacons sit on the seabed listening for acoustic chirps from the sonar and retransmit back in a different frequency band after a fixed time delay. After reconstruction the beacons appear in the SAS image as point-source targets, blurred by towfish motion, from which the tow-path can be determined by triangulation. The effect of reconstructing the continuous towfish motion as discrete along-track `hops' is also investigated. Simulations of a towfish path with 20 cm sway amplitude and typical measurement timing errors show a significant improvement in image quality using two active beacons.

Measuring The Tow-Path; Edward N. Pilbrow; Michael P. Hayes

2003-01-01T23:59:59.000Z

439

Acoustic sand detector for fluid flowstreams  

DOE Patents (OSTI)

The particle volume and particle mass production rate of particulate solids entrained in fluid flowstreams such as formation sand or fracture proppant entrained in oil and gas production flowstreams is determined by a system having a metal probe interposed in a flow conduit for transmitting acoustic emissions created by particles impacting the probe to a sensor and signal processing circuit which produces discrete signals related to the impact of each of the particles striking the probe. The volume or mass flow rate of particulates is determined from making an initial particle size distribution and particle energy distribution and comparing the initial energy distribution and/or the initial size distribution with values related to the impact energies of a predetermined number of recorded impacts. The comparison is also used to recalibrate the system to compensate for changes in flow velocity.

Beattie, Alan G. (Corrales, NM); Bohon, W. Mark (Frisco, TX)

1993-01-01T23:59:59.000Z

440

Building Energy Software Tools Directory: Tools by Country -...  

NLE Websites -- All DOE Office Websites (Extended Search)

Czech Republic C Tool Applications Free Recently Updated Czech National Calculation Tool EPBD, Energy Performance Certificate, Delivered energy, Energy Demand Calculation...

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Building Energy Software Tools Directory: Indoor Humidity Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Africa Spain Sweden Switzerland United Kingdom United States Related Links Indoor Humidity Tools Indoor Humidity Tools logo. Integrated computer program intended to assist in...

442

NEAMS ToolKit: advanced computational tools for modeling & simulation...  

NLE Websites -- All DOE Office Websites (Extended Search)

NEAMS ToolKit: advanced computational tools for modeling & simulation of advanced reactor systems Director's Welcome Organization Achievements Highlights Fact Sheets, Brochures &...

443

Methane Recovery from Hydrate-bearing Sediments  

Science Conference Proceedings (OSTI)

Gas hydrates are crystalline compounds made of gas and water molecules. Methane hydrates are found in marine sediments and permafrost regions; extensive amounts of methane are trapped in the form of hydrates. Methane hydrate can be an energy resource, contribute to global warming, or cause seafloor instability. This study placed emphasis on gas recovery from hydrate bearing sediments and related phenomena. The unique behavior of hydrate-bearing sediments required the development of special research tools, including new numerical algorithms (tube- and pore-network models) and experimental devices (high pressure chambers and micromodels). Therefore, the research methodology combined experimental studies, particle-scale numerical simulations, and macro-scale analyses of coupled processes. Research conducted as part of this project started with hydrate formation in sediment pores and extended to production methods and emergent phenomena. In particular, the scope of the work addressed: (1) hydrate formation and growth in pores, the assessment of formation rate, tensile/adhesive strength and their impact on sediment-scale properties, including volume change during hydrate formation and dissociation; (2) the effect of physical properties such as gas solubility, salinity, pore size, and mixed gas conditions on hydrate formation and dissociation, and it implications such as oscillatory transient hydrate formation, dissolution within the hydrate stability field, initial hydrate lens formation, and phase boundary changes in real field situations; (3) fluid conductivity in relation to pore size distribution and spatial correlation and the emergence of phenomena such as flow focusing; (4) mixed fluid flow, with special emphasis on differences between invading gas and nucleating gas, implications on relative gas conductivity for reservoir simulations, and gas recovery efficiency; (5) identification of advantages and limitations in different gas production strategies with emphasis; (6) detailed study of CH4-CO2 exchange as a unique alternative to recover CH4 gas while sequestering CO2; (7) the relevance of fines in otherwise clean sand sediments on gas recovery and related phenomena such as fines migration and clogging, vuggy structure formation, and gas-driven fracture formation during gas production by depressurization.

J. Carlos Santamarina; Costas Tsouris

2011-04-30T23:59:59.000Z

444

Fast crash recovery in RAMCloud  

Science Conference Proceedings (OSTI)

RAMCloud is a DRAM-based storage system that provides inexpensive durability and availability by recovering quickly after crashes, rather than storing replicas in DRAM. RAMCloud scatters backup data across hundreds or thousands of disks, and it harnesses ... Keywords: crash recovery, main memory databases, scalability, storage systems

Diego Ongaro; Stephen M. Rumble; Ryan Stutsman; John Ousterhout; Mendel Rosenblum

2011-10-01T23:59:59.000Z

445

Biosurfactant and enhanced oil recovery  

DOE Patents (OSTI)

A pure culture of Bacillus licheniformis strain JF-2 (ATCC No. 39307) and a process for using said culture and the surfactant lichenysin produced thereby for the enhancement of oil recovery from subterranean formations. Lichenysin is an effective surfactant over a wide range of temperatures, pH's, salt and calcium concentrations.

McInerney, Michael J. (Norman, OK); Jenneman, Gary E. (Norman, OK); Knapp, Roy M. (Norman, OK); Menzie, Donald E. (Norman, OK)

1985-06-11T23:59:59.000Z

446

Environmental regulations handbook for enhanced oil recovery. Final report  

SciTech Connect

A guide to environmental laws and regulations which have special significance for enhanced oil recovery (EOR) is presented. The Clean Air Act, the Clean Water Act, the Safe Drinking Water Act, Resource Conservation and Recovery Act, federal regulations, and state regulations are discussed. This handbook has been designed as a planning tool and a convenient reference source. The 16 states included comprise the major oil-producing states in various regions of the state. The major topics covered are: general guidelines for complying with environmental laws and regulations; air pollution control; water pollution control; protecting drinking water: underground injection control; hazardous waste management; and federal laws affecting siting or operation of EOR facilities. (DMC)

Wilson, T.D.

1980-08-01T23:59:59.000Z

447

ARKANSAS RECOVERY ACT SNAPSHOT | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ARKANSAS RECOVERY ACT SNAPSHOT ARKANSAS RECOVERY ACT SNAPSHOT ARKANSAS RECOVERY ACT SNAPSHOT Arkansas has substantial natural resources, including gas, oil, wind, biomass, and hydroelectric power. The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and environmental future. The Recovery Act investments in Arkansas are supporting a broad range of clean energy projects, from energy efficiency and the smart grid to advanced battery manufacturing and renewable energy. Through these investments, Arkansas's businesses, non-profits, and local governments are creating quality jobs today and positioning Arkansas to play an important role in the new energy economy of the future. ARKANSAS RECOVERY ACT SNAPSHOT More Documents & Publications

448

ALASKA RECOVERY ACT SNAPSHOT | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ALASKA RECOVERY ACT SNAPSHOT ALASKA RECOVERY ACT SNAPSHOT ALASKA RECOVERY ACT SNAPSHOT Alaska has substantial natural resources, including oil, gas, coal, solar, wind, geothermal, and hydroelectric power .The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and environmental future. The Recovery Act investments in Alaska are supporting a broad range of clean energy projects, from energy efficiency and electric grid improvements to geothermal power. Through these investments, Alaska's businesses, universities, non-profits, and local governments are creating quality jobs today and positioning Alaska to play an important role in the new energy economy of the future. ALASKA RECOVERY ACT SNAPSHOT More Documents & Publications

449

GEORGIA RECOVERY ACT SNAPSHOT | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

GEORGIA RECOVERY ACT SNAPSHOT GEORGIA RECOVERY ACT SNAPSHOT GEORGIA RECOVERY ACT SNAPSHOT Georgia has substantial natural resources, including biomass and hydroelectric power .The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and environmental future. The Recovery Act investments in Georgia are supporting a broad range of clean energy projects, from energy efficiency and the smart grid to environmental cleanup and alternative fuels and vehicles. Through these investments, Georgia's businesses, universities, non-profits, and local governments are creating quality jobs today and positioning Georgia to play an important role in the new energy economy of the future. GEORGIA RECOVERY ACT SNAPSHOT More Documents & Publications

450

ARIZONA RECOVERY ACT SNAPSHOT | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ARIZONA RECOVERY ACT SNAPSHOT ARIZONA RECOVERY ACT SNAPSHOT ARIZONA RECOVERY ACT SNAPSHOT Arizona has substantial natural resources, including coal, solar, and hydroelectric resources. The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and environmental future. The Recovery Act investments in Arizona reflect a broad range of clean energy projects, from energy efficiency and the smart grid to transportation, carbon capture and storage, and geothermal energy. Through these investments, Arizona's businesses, universities, non-profits, and local governments are creating quality jobs today and positioning Arizona to play an important role in the new energy economy of the future. ARIZONA RECOVERY ACT SNAPSHOT More Documents & Publications

451

ARKANSAS RECOVERY ACT SNAPSHOT | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ARKANSAS RECOVERY ACT SNAPSHOT ARKANSAS RECOVERY ACT SNAPSHOT ARKANSAS RECOVERY ACT SNAPSHOT Arkansas has substantial natural resources, including gas, oil, wind, biomass, and hydroelectric power. The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and environmental future. The Recovery Act investments in Arkansas are supporting a broad range of clean energy projects, from energy efficiency and the smart grid to advanced battery manufacturing and renewable energy. Through these investments, Arkansas's businesses, non-profits, and local governments are creating quality jobs today and positioning Arkansas to play an important role in the new energy economy of the future. ARKANSAS RECOVERY ACT SNAPSHOT More Documents & Publications

452

GEORGIA RECOVERY ACT SNAPSHOT | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

GEORGIA RECOVERY ACT SNAPSHOT GEORGIA RECOVERY ACT SNAPSHOT GEORGIA RECOVERY ACT SNAPSHOT Georgia has substantial natural resources, including biomass and hydroelectric power .The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and environmental future. The Recovery Act investments in Georgia are supporting a broad range of clean energy projects, from energy efficiency and the smart grid to environmental cleanup and alternative fuels and vehicles. Through these investments, Georgia's businesses, universities, non-profits, and local governments are creating quality jobs today and positioning Georgia to play an important role in the new energy economy of the future. GEORGIA RECOVERY ACT SNAPSHOT More Documents & Publications

453

Enclosed jar tool  

SciTech Connect

A jar tool is described comprising: a mandrel adapted for connection to a piece of drill string at one end of the tool; a housing axially movable relative to the mandrel and adapted for connection to the drill string at the opposite end of the tool; first and second pairs of abutment faces between the mandrel and the housing defining jar and bump positions of the tool, respectively, the first and second pairs of abutment faces located in an abutment chamber; a piston slidably located between walls of the mandrel and the housing and having valve means operable to regulate the passage of hydraulic fluid from a first chamber on one side of the piston between the mandrel and the housing to a second chamber on the other side of the piston between the mandrel and the housing, the valve means including passages for permitting the hydraulic fluid to flow through the piston and between the piston and the walls of the mandrel and housing; and sealing means between the housing and mandrel operable to seal the first pair of abutment faces from outside contamination in the abutment chamber and seal the abutment chamber from the first and second chambers, the first and second pairs of abutment faces being enclosed within the jar tool.

Ring, C.P.

1987-04-21T23:59:59.000Z

454

APS Guideline for Hand Tool and Portable Power Tool Usage  

NLE Websites -- All DOE Office Websites (Extended Search)

Hand Tool and Portable Power Tool Usage Hand Tool and Portable Power Tool Usage Introduction CAT/XSD recognizes that the misuse and improper maintenance of hand tools and portable power tools cause a significant number of injuries to even "experienced" workers. Consequently, CAT/XSD has adopted the following policies and procedures to minimize the hazards associated with the use of such equipment at the APS. These guidelines apply to all use of hand tools and portable power tools by CAT/XSD personnel while performing maintenance or installation activities at the APS. Although CAT/XSD feels that most of the guidelines also apply to tool usage during experimental activities, CAT/XSD will not require that short-term users complete the training described below. Using Tools Safely If you have not had formal training in the use of common tools, either view

455

Guidebook for Using the Tool BEST Cement: Benchmarking and Energy Savings Tool for the Cement Industry  

E-Print Network (OSTI)

Concepts of Waste Heat Recovery in Cement Plants EnergyConcepts of Waste Heat Recovery in Cement Plants Energyor Photo: Waste heat recovery at cement plant, image taken

Galitsky, Christina

2009-01-01T23:59:59.000Z

456

An Intercomparison of Current Measurements Using a Vector Measuring Current Meter, an Acoustic Doppler Current Profiler, and a Recently Developed Acoustic Current Meter  

Science Conference Proceedings (OSTI)

Horizontal current measurements were obtained simultaneously with a vector measuring current meter (VMCM), an acoustic Doppler current profiler (ADCP), and the recently developed Falmouth Scientific, Inc., acoustic current meter (ACM) during a ...

T. P. Gilboy; T. D. Dickey; D. E. Sigurdson; X. Yu; D. Manov

2000-04-01T23:59:59.000Z

457

Provide Data and Tools  

NLE Websites -- All DOE Office Websites (Extended Search)

Provide Data and Tools Print E-mail Provide Data and Tools Print E-mail With the advance of observational capabilities, computational power, and scientific research, there is both an opportunity for scientific progress in the study of the Earth system and a need to manage the data and information generated about it. As computational capabilities improve, data volume will continue to grow at an accelerating rate. It is crucial to continue to collect and store these records, but this increased output will also present data management challenges. Addressing this data-volume challenge will require advanced technology to link users to the various data providers and cloud-based tools to facilitate collaboration. In the coming decade, USGCRP will take a leadership role in coordinating these networks, by providing shared data access, analytic capabilities, and modeling frameworks to support integrated research and decision support.

458

Bumping and jarring tool  

SciTech Connect

A bumping and jarring tool for a well drill string is provided having a telescoping housing and mandrel with an annular hydraulic chamber therebetween divided into two portions. The lower portion is exposed to the ambient hydrostatic well pressure and the upper portion varies in volume as the tool opens and closes. When the tool is opened a jar is produced by a valve between the chamber portions which restricts hydraulic fluid flow between the chamber portions resulting in a pressure drop in the upper portion and by a pressure increasing element in the lower portion which increases the pressure therein while the pressure drops in the upper portion. When the valve permits unrestricted flow again, the sudden return to pressure equilibrium produces the jar stroke.

Wenzel, K.H.

1980-10-28T23:59:59.000Z

459

Building Energy Software Tools Directory: Building Energy Analyzer  

NLE Websites -- All DOE Office Websites (Extended Search)

Building Energy Analyzer Building Energy Analyzer Building Energy Analyzer logo. Provides quick economic analysis for commercial and industrial buildings. Building Energy Analyzer (BEA) estimates annual and monthly loads and costs associated with air-conditioning, heating, on-site power generation, thermal storage, and heat recovery systems for a given building and location. The user can compare the performance of standard and high efficiency electric chillers, variable speed electric chillers, absorption chillers, engine chillers, thermal storage, on-site generators, heat recovery, or desiccant systems. The user can also prepare side-by-side economic comparisons of different energy options and equipment life cycle cost analysis. The BEA is a system screening tool. It is a tool that is

460

Evaluation of the Acoustic Doppler Velocimeter (ADV) for Turbulence Measurements*  

Science Conference Proceedings (OSTI)

Accuracy of the acoustic Doppler velocimeter (ADV) is evaluated in this paper. Simultaneous measurements of open-channel flow were undertaken in a 17-m flume using an ADV and a laser Doppler velocimeter. Flow velocity records obtained by both ...

G. Voulgaris; J. H. Trowbridge

1998-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Speech coding, reconstruction and recognition using acoustics and electromagnetic waves  

DOE Patents (OSTI)

The use of EM radiation in conjunction with simultaneously recorded acoustic speech information enables a complete mathematical coding of acoustic speech. The methods include the forming of a feature vector for each pitch period of voiced speech and the forming of feature vectors for each time frame of unvoiced, as well as for combined voiced and unvoiced speech. The methods include how to deconvolve the speech excitation function from the acoustic speech output to describe the transfer function each time frame. The formation of feature vectors defining all acoustic speech units over well defined time frames can be used for purposes of speech coding, speech compression, speaker identification, language-of-speech identification, speech recognition, speech synthesis, speech translation, speech telephony, and speech teaching.

Holzrichter, John F. (Berkeley, CA); Ng, Lawrence C. (Danville, CA)

1998-01-01T23:59:59.000Z

462

Acoustic Logs At Coso Geothermal Area (1977) | Open Energy Information  

Open Energy Info (EERE)

Coso Geothermal Area (1977) Coso Geothermal Area (1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Coso Geothermal Area (1977) Exploration Activity Details Location Coso Geothermal Area Exploration Technique Acoustic Logs Activity Date 1977 Usefulness not indicated DOE-funding Unknown Notes Acoustic logs indicate fractured rock and potentially permeable zones. References Galbraith, R. M. (1 May 1978) Geological and geophysical analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Goranson, C.; Schroeder, R. (1 June 1978) Static downhole characteristics of well CGEH-1 at Coso Hot Springs, China Lake, California Retrieved from "http://en.openei.org/w/index.php?title=Acoustic_Logs_At_Coso_Geothermal_Area_(1977)&oldid=510216"

463

Dual output acoustic wave sensor for molecular identification  

DOE Patents (OSTI)

The invention comprises a method for the identification and quantification of sorbed chemical species onto a coating of a device capable of generating and receiving an acoustic wave, by measuring the changes in the velocity of the acoustic wave resulting from the sorption of the chemical species into the coating as the wave travels through the coating and by measuring the changes in the attenuation of an acoustic wave resulting from the sorption of the chemical species into the coating as the wave travels through the coating. The inventive method further correlates the magnitudes of the changes of velocity with respect to changes of the attenuation of the acoustic wave to identify the sorbed chemical species. The absolute magnitudes of the velocity changes or the absolute magnitude of the attenuation changes are used to determine the concentration of the identified chemical species.

Frye, G.C.; Martin, S.J.

1990-10-03T23:59:59.000Z

464

Acoustic Method for Fish Counting and Fish Sizing in Tanks  

E-Print Network (OSTI)

A-123: 3.01.2004–2.28.2005 Acoustic Method for Fish Countingand Fish Sizing in Tanks W.A. Kuperman and Philippe Rouxlower the costs of raising fish to marketable size. Water,

Kuperman, William A.; Roux, Philippe

2004-01-01T23:59:59.000Z

465

AMOC: Acoustic monitoring of the ocean climate of the Arctic  

Science Conference Proceedings (OSTI)

The overall objective of AMOC is to develop and design an acoustic system for long?term monitoring of the ocean temperature and ice thickness in the Arctic Ocean including the Fram Strait

Ola M. Johannessen; AMOC Group

1999-01-01T23:59:59.000Z

466

Direct-form adaptive equalization for underwater acoustic communication  

E-Print Network (OSTI)

Adaptive equalization is an important aspect of communication systems in various environments. It is particularly important in underwater acoustic communication systems, as the channel has a long delay spread and is subject ...

Yellepeddi, Atulya

2012-01-01T23:59:59.000Z

467

The Measurement of Bubble-Size Distributions by Acoustical Backscatter  

Science Conference Proceedings (OSTI)

A multifrequency acoustical-backscatter technique is described for determining the size distribution of bubbles with radii between 8 and 130 µm. The method makes use of the resonance in the microbubbles and operates at six frequencies ranging ...

Svein Vagle; David M. Farmer

1992-10-01T23:59:59.000Z

468

Acoustic Waveform Logging - Advances In Theory And Application  

E-Print Network (OSTI)

Full-waveform acoustic logging has made significant advances in both theory and application in recent years, and these advances have greatly increased the capability of log analysts to measure the physical properties of ...

Cheng, C. H.

469

Examining transmission power in minimum capacity underwater acoustic networks  

E-Print Network (OSTI)

This paper explores the prospect of reducing the transmission power required to operate links within an underwater acoustic network by minimizing the total capacity of the network while maintaining certain data flow ...

Stanchak, Kathryn E

2010-01-01T23:59:59.000Z

470

Speech coding, reconstruction and recognition using acoustics and electromagnetic waves  

DOE Patents (OSTI)

The use of EM radiation in conjunction with simultaneously recorded acoustic speech information enables a complete mathematical coding of acoustic speech. The methods include the forming of a feature vector for each pitch period of voiced speech and the forming of feature vectors for each time frame of unvoiced, as well as for combined voiced and unvoiced speech. The methods include how to deconvolve the speech excitation function from the acoustic speech output to describe the transfer function each time frame. The formation of feature vectors defining all acoustic speech units over well defined time frames can be used for purposes of speech coding, speech compression, speaker identification, language-of-speech identification, speech recognition, speech synthesis, speech translation, speech telephony, and speech teaching. 35 figs.

Holzrichter, J.F.; Ng, L.C.

1998-03-17T23:59:59.000Z

471

Acoustic Tomographic Monitoring of the Atmospheric Surface Layer  

Science Conference Proceedings (OSTI)

Acoustic tomography is proposed as a method for monitoring near-surface atmospheric temperature and wind velocity fields. Basic issues relating to the feasibility and implementation of atmospheric tomography are discussed. Among these issues are ...

D. Keith Wilson; Dennis W. Thomson

1994-06-01T23:59:59.000Z

472

Laser-Acoustic Hygrometer: Procedure and Results of Field Measurements  

Science Conference Proceedings (OSTI)

Trial field measurements of humidity fluctuations are taken by a laser-acoustic hygrometer consisting of a CO laser, a mechanical modulator, a detector, an audio-frequency amplifier, and a device for processing signals. The proposed method is ...

Boris S. Agrovskii; Alexandre S. Gurvich; Vitaly P. Kukharets; Valery V. Vorob’ev

1998-02-01T23:59:59.000Z

473

Acoustic classification of buried objects with mobile sonar platforms  

E-Print Network (OSTI)

In this thesis, the use of highly mobile sonar platforms is investigated for the purpose of acoustically classifying compact objects on or below the seabed. The extension of existing strategies, including synthetic aperture ...

Edwards, Joseph Richard, 1971-

2006-01-01T23:59:59.000Z

474

Acoustic Waves in the Turbulent Atmosphere: A Review  

Science Conference Proceedings (OSTI)

The subject of atmospheric acoustics and its role in atmospheric research and in development of modern methods of ground-based remote sensing of the atmosphere are outlined. A historical overview of investigations of the effect of atmospheric ...

M. A. Kallistratova

2002-08-01T23:59:59.000Z

475

Using Acoustic Emission in Fatigue and Fracture Materials Research  

Science Conference Proceedings (OSTI)

J.E. Coulter et al., "Acoustic Emission Monitoring of Fossil-Fuel Power Plants," Mat. Eval., 46 (2) (1988), pp. 230–237. 13. P.J. de Groot, P.M. Wijnen, and R.B.F.

476

Laboratory Comparisons of Acoustic and Optical Sensors for Microbubble Measurement  

Science Conference Proceedings (OSTI)

This paper presents the results of a recent comparison between three microbubble size spectrum measurement systems. These systems are the light-wattering bubble counter, the photographic bubble-imaging system, and the acoustic resonator array. ...

Ming Vang Su; Douglas Todoroff; John Cartmill

1994-02-01T23:59:59.000Z

477

Operating an Acoustic Doppler Current Profiler aboard a Container Vessel  

Science Conference Proceedings (OSTI)

Since October 1992 an acoustic Doppler current profiler (ADCP) has been in near-continuous operation on board a 118-m-long container vessel, the container motor vessel Oleander, which operates on a weekly schedule between Port Elizabeth, New ...

C. N. Flagg; G. Schwartze; E. Gottlieb; T. Rossby

1998-02-01T23:59:59.000Z

478

Reduced bandwidth frequency domain equalization for underwater acoustic communications  

E-Print Network (OSTI)

Two challenges facing adaptive decision feedback equalizers (DFEs) in the underwater acoustic channel are those of the channel changing too rapidly to allow for the stable adaptation of the number of coefficients required ...

Wornell, Gregory W.

479

Listening to Raindrops from Underwater: An Acoustic Disdrometer  

Science Conference Proceedings (OSTI)

Different sized raindrops splashing on a water surface produce sound underwater that is distinctive and can be used to measure the drop size distribution in the rain. Five acoustically significant raindrop sizes are described. An inversion of the ...

Jeffrey A. Nystuen

2001-10-01T23:59:59.000Z

480

MAC and Routing Protocols for Mobile Underwater Acoustic Sensor Swarms.  

E-Print Network (OSTI)

??Underwater Acoustic Sensor Networks (UW-ASNs) have recently been proposed as a way to explore and observe the ocean, which covers two-thirds of the Earth's surface.… (more)

Noh, Young Tae

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "recovery tool acoustic" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Modeling the Performance of an Acoustic Doppler Current Profiler  

Science Conference Proceedings (OSTI)

A systematic examination of measurement error in acoustic Doppler current profiler (ADCP) velocity estimates, in the limit of large signal-to-noise ratio, is made using a system model and sonar signal simulations coupled into an ADCP. The model ...

T. K. Chereskin; A. J. Harding

1993-02-01T23:59:59.000Z

482

Strongly driven ion acoustic waves in laser produced plasmas  

Science Conference Proceedings (OSTI)

This paper present an experimental study of ion acoustic waves with wavenumbers corresponding to stimulated Brillouin scattering. Time resolved Thomson scattering in frequency and wavenumber space, has permitted to observe the dispersion relation of the waves as a function of the laser intensity. Apart from observing ion acoustic waves associated with a strong second component is observed at laser intensities above 10{sup 13}Wcm{sup {minus}2}.

Baldis, H.A.; Labaune, C.; Renard, N. [Ecole Polytechnique, 91 - Palaiseau (France)] [and others

1994-09-20T23:59:59.000Z

483

Acoustic energy-driven fluid pump and method  

DOE Patents (OSTI)

Bulk fluid motion is promoted in a gaseous fluid contained within a conduit system provided with a diffuser without the need for a mean pressure differential across the conduit system. The contacting of the gaseous fluid with unsteady energy at a selected frequency and pressure amplitude induces fluid flow through the conical diffuser. The unsteady energy can be provided by pulse combustors, thermoacoustic engines, or acoustic energy generators such as acoustic speakers.

Janus, Michael C.; Richards, George A.; Robey, Edward H.

1997-12-01T23:59:59.000Z

484

Coupling light into graphene plasmons through surface acoustic waves  

E-Print Network (OSTI)

We propose a scheme for coupling laser light into graphene plasmons with the help of electrically generated surface acoustic waves. The surface acoustic wave forms a diffraction grating which allows to excite the long lived phonon-like branch of the hybridized graphene plasmon-phonon dispersion with infrared laser light. Our approach avoids patterning the graphene sheet, does not rely on complicated optical near-field techniques, and allows to electrically switch the coupling between far field radiation and propagating graphene plasmons.

Schiefele, Jürgen; Sols, Fernando; Calle, Fernando; Guinea, Francisco

2013-01-01T23:59:59.000Z

485

Recovery Act Reports | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery Act » Recovery Act Reports Recovery Act » Recovery Act Reports Recovery Act Reports The following is a list of the oversight results by the Office of Inspector General regarding The Department's programs, grants, and projects funded under the Recovery Act. November 25, 2013 Audit Report: OAS-RA-14-02 The Department of Energy's American Recovery and Reinvestment Act Energy Efficiency and Conservation Block Grant Program - District of Columbia September 27, 2013 Audit Report: OAS-RA-13-31 The Department of Energy's Hydrogen and Fuel Cells Program September 19, 2013 Examination Report: OAS-RA-13-30 Alamo Area Council of Governments - Weatherization Assistance Program Funds Provided by the American Recovery and Reinvestment Act of 2009 September 9, 2013 Audit Report: IG-0893 Follow-up Audit of the Department of Energy's Financial Assistance for

486

HVAC Energy Recovery Design and Economic Evaluation  

E-Print Network (OSTI)

ENRECO has prepared this paper on HVAC energy recovery to provide the engineer with an overview of the design engineering as well as the economic analysis considerations necessary to evaluate the potential benefits of energy recovery.

Kinnier, R. J.

1979-01-01T23:59:59.000Z

487

COUNTER DISASTER AND RECOVERY PLAN -UNIVERSITY RECORDS  

E-Print Network (OSTI)

...................................................................................10 3.1 Disaster Response and Recovery Team...........................................10 3.2 Emergency Disaster Response.......................................................................23 6.1 AssessingCOUNTER DISASTER AND RECOVERY PLAN - UNIVERSITY RECORDS Records Management & Archives Murdoch

488

Web Services for Recovery.gov  

E-Print Network (OSTI)

established and widely supported Web technologies such asof Information Report 2009-035 Web Services for Recovery.govof Recovery.gov as a user-friendly Web site and hence most

Wilde, Erik; Kansa, Eric C; Yee, Raymond

2009-01-01T23:59:59.000Z

489

Building Energy Software Tools Directory: Tools by Country -...  

NLE Websites -- All DOE Office Websites (Extended Search)

Ireland P Tool Applications Free Recently Updated PASSPORT heating requirements, passive solar, residential buildings, standards...

490

OPERATING PROCEDURE FOR THE PORTABLE ACOUSTIC MONITORING PACKAGE (PAMP)  

Science Conference Proceedings (OSTI)

The Portable Acoustic Monitoring Package (PAMP) has been designed to record and monitor acoustic signals in high-pressure natural gas (NG) transmission lines. Of particular interest are the three acoustic signals associated with a pipeline fracture. The system is portable (less than 30 lbm) and can be used at all line pressures up to 1000 psig. The PAMP requires a shut-off valve equipped 1/2 inch NPT access port in the pipeline. It is fully functional over the typical pressure range found in the natural gas transmission pipelines in the West Virginia, Virginia, Pennsylvania, and Ohio areas. With the use of the PAMP, a full spectrum of acoustic signals can be recorded and defined in terms of acoustic energy in decibels. To detect natural gas pipeline infringements and leaks, the acoustic energy generated inside the line is monitored with a sensitive pressure-equalized microphone and a step function type {Delta}p transducer. The assembly is mounted on a 1000 psig pipe fitting-tree called the PAMP. The electronics required to record, store and analyze the data are described within this report in the format of an operating manual.

John L. Loth; Gary J. Morris; George M. Palmer; Richard Guiler; Patrick Browning

2004-08-29T23:59:59.000Z

491

Vermont Recovery Act State Memo | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Vermont Recovery Act State Memo Vermont Recovery Act State Memo The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and...

492

Colorado Recovery Act State Memo | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Colorado Recovery Act State Memo Colorado Recovery Act State Memo The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and...

493

Recovery Act: Smart Grid Interoperability Standards and Framework...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Act: Smart Grid Interoperability Standards and Framework Recovery Act: Smart Grid Interoperability Standards and Framework Congressional Testimony Recovery Act Recovery Act...

494

Implementing the American Recovery and Reinvestment Act  

– $20 million for geologic carbon sequestration training and research . Recovery Act Tax Provisions on Clean Energy Production Tax Credit

495

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

L ABORATORY Distributed Generation with Heat Recovery andequal opportunity employer. Distributed Generation with Heatenergy resources (DER), distributed generation (DG), and

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

496

Recovery Act NIST Construction Grant Program  

Science Conference Proceedings (OSTI)

Recovery Act NIST Construction Grant Program. ... Fraud Prevention Training for Recipients; Fraud Indicators Pamphlet; Red Flags of Collusion ...

2011-08-17T23:59:59.000Z

497

Laboratory Evaluation of Energy Recovery Ventilators  

SciTech Connect

As deep retrofit measures and new construction practices are realizing lower infiltration levels in increasingly tighter envelopes, performance issues can arise with water vapor intrusion in building envelopes and the operation of exhaust only appliances in a depressurized home. Unbalancing (reducing exhaust airflows) of an energy recovery ventilator (ERV) can provide a means to supply makeup air and reduce the level of home depressurization to mitigate these issues, helping realize exhaust-only appliance rated performance, achieve safe atmospherically vented combustion, and/or improve envelope durability. ERV balanced flow operation is well documented, but there is not public domain information available that empirically establishes the effect of unbalanced flow on sensible and latent exchange, especially in the now dominant membrane type ERV used in residential applications. This laboratory evaluation focused on unbalanced flow performance of a membrane type ERV delivering 200 standard cubic feet per minute (SCFM )of supply air. The dataset generated yielded a limited set of curve fit algorithms for unbalanced flow performance that can be used to supplement current modeling approaches in simulation tools like EnergyPlus. Building America BA teams can then utilize such models to analyze whole house effects and determine best practices associated with unbalanced ERV operations.

Kosar, D.

2013-05-01T23:59:59.000Z

498

Tools and Products  

Science Conference Proceedings (OSTI)

A look at new products on the market, including the BOXX Technologies' Apexx 4 Super-Workstation and renderBOXX Classic 7500, Dimension 3D Printers from Tekpro Group, Micro