Sample records for reactivate ts operating

  1. Reactive Power Operation Analysis of a Single-Phase EV/PHEV Bidirectional Battery Charger

    E-Print Network [OSTI]

    Tolbert, Leon M.

    of the electric grid by supplying ancillary services such as reactive power compensation, voltage regulation, charger, electric vehicle, EV, PHEV, reactive power, V2G. I. INTRODUCTION According to the internationalReactive Power Operation Analysis of a Single-Phase EV/PHEV Bidirectional Battery Charger Mithat C

  2. SPACE WEATHER AND THE INCIDENCE OF REACTIVE "OFF-COST" OPERATIONS IN THE PJM POWER GRID

    E-Print Network [OSTI]

    Schrijver, Karel

    SPACE WEATHER AND THE INCIDENCE OF REACTIVE "OFF-COST" OPERATIONS IN THE PJM POWER GRID 7.6 Kevin F the price of electricity in the PJM power grid. In this paper we examine one of the mechanisms by which space weather impacts the electricity market in the PJM power grid. The starting point of this paper

  3. S and 4 Reactor: Operating Lifetime and Estimates of Temperature and Burnup Reactivity Coefficients

    SciTech Connect (OSTI)

    King, Jeffrey C.; El-Genk, Mohamed S. [Institute for Space and Nuclear Power Studies, University of New Mexico, Albuquerque, NM 87131 (United States); Chemical and Nuclear Engineering Dept., University of New Mexico, Albuquerque, NM 87131 (United States)

    2006-01-20T23:59:59.000Z

    The S and 4 reactor has a sectored, Mo-14%Re solid core for avoidance of single point failures in reactor cooling and Closed Brayton Cycle (CBC) energy conversion. The reactor is loaded with UN fuel, cooled with a He-Xe gas mixture at {approx}1200 K and operates at steady thermal power of 550 kW. Following a launch abort accident, the axial and radial BeO reflectors easily disassemble upon impact so that the bare reactor is subcriticial when submerged in wet sand or seawater and the core voids are filled with seawater. Spectral Shift Absorber (SSA) additives have been shown to increase the UN fuel enrichment and significantly reduce the total mass of the reactor. This paper investigates the effects of SSA additions on the temperature and burnup reactivity coefficients and the operational lifetime of the S and 4 reactor. SSAs slightly decrease the temperature reactivity feedback coefficient, but significantly increase the operating lifetime by decreasing the burnup reactivity coefficient. With no SSAs, fuel enrichment is only 58.5 wt% and the estimated operating lifetime is the shortest (7.6 years) with the highest temperature and burnup reactivity feedback coefficients (-0.2709 cent /K and -1.3470 $/atom%). With europium-151 and gadolinium-155 additions, the enrichment (91.5 and 94 wt%) and operating lifetime (9.9 and 9.8 years) of the S and 4 reactor are the highest while the temperature and burnup reactivity coefficients (-0.2382 and -0.2447 cent /K; -0.9073 and 0.8502 $/atom%) are the lowest.

  4. Abstract--This paper proposes a two-level framework for the operation of a competitive market for reactive power ancillary

    E-Print Network [OSTI]

    Cañizares, Claudio A.

    and the selected reactive power service providers. Index Terms- System operation, ancillary services, electricity reactive power provisions in the context of deregulated electricity markets, namely, reactive power for reactive power ancillary services. It is argued that the first-level, i.e. reactive power procurement

  5. Reactive and voltage monitoring: The challenge for the system operators in the 1980's

    SciTech Connect (OSTI)

    Willson, J.D.

    1981-05-01T23:59:59.000Z

    In order to gain perspective on the monitoring program for PJM, background relative to the physical characteristics and operating philosophy of the pool is offered. PJM is comprised of 11 electric utilities serving approximately 48,700 square miles, encompassing about 75% of Penna, 97% of N.J., all of Del and the District of Columbia, 60% of Md, and 1% of Va. The generating capability is comprised of 532 units at 116 generating stations, and totals approximately 45,000 MW. The PJM system peak load for 1980 was 34,420 MW. PJM has 27 tie lines with its neighboring systems. Although comprised of 11 utilities, the PJM system is operated as if it were a single company. Reasons for the PJM real-time monitoring system are presented and relevant details are discussed. Topics considered include operating criteria. Reactive and Voltage Monitoring, Current Operating Restrictions off-line analysis, and future requirements are discussed.

  6. Mineralogical characteristics and transformations during long-term operation of a zerovalent iron reactive barrier

    SciTech Connect (OSTI)

    Phillips, Debra Helen [ORNL; Watson, David B [ORNL; Roh, Yul [ORNL; Gu, Baohua [ORNL

    2003-04-01T23:59:59.000Z

    Design and operation of Fe{sup 0} permeable reactive barriers (PRBs) can be improved by understanding the long-term mineralogical transformations that occur within PRBs. Changes in mineral precipitates, cementation, and corrosion of Fe{sup 0} filings within an in situ pilot-scale PRB were examined after the first 30 months of operation and compared with results of a previous study of the PRB conducted 15 months earlier using X-ray diffraction and scanning electron microscopy employing energy dispersive X-ray and backscatter electron analyses. Iron (oxy)hydroxides, aragonite, and maghemite and/or magnetite occurred throughout the cores collected 30 mo after installation. Goethite, lepidocrocite, mackinawite, aragonite, calcite, and siderite were associated with oxidized and cemented areas, while green rusts were detected in more reduced zones. Basic differences from our last detailed investigation include (i) mackinawite crystallized from amorphous FeS, (ii) aragonite transformed into calcite, (iii) akaganeite transformed to goethite and lepidocrocite, (iv) iron (oxy)hydroxides and calcium and iron carbonate minerals increased, (v) cementation was greater in the more recent study, and (vi) oxidation, corrosion, and disintegration of Fe{sup 0} filings were greater, especially in cemented areas, in the more recent study. If the degree of corrosion and cementation that was observed from 15 to 30 mo after installation continues, certain portions of the PRB (i.e., up-gradient entrance of the ground water to the Fe{sup 0} section of the PRB) may last less than five more years, thus reducing the effectiveness of the PRB to mitigate contaminants.

  7. Photovoltaic solar system connected to the electric power grid operating as active power generator and reactive power compensator

    SciTech Connect (OSTI)

    Albuquerque, Fabio L.; Moraes, Adelio J.; Guimaraes, Geraldo C.; Sanhueza, Sergio M.R.; Vaz, Alexandre R. [Universidade Federal de Uberlandia, Uberlandia-MG, CEP 38400-902 (Brazil)

    2010-07-15T23:59:59.000Z

    In the case of photovoltaic (PV) systems acting as distributed generation (DG) systems, the DC energy that is produced is fed to the grid through the power-conditioning unit (inverter). The majority of contemporary inverters used in DG systems are current source inverters (CSI) operating at unity power factor. If, however, we assume that voltage source inverters (VSI) can replace CSIs, we can generate reactive power proportionally to the remaining unused capacity at any given time. According to the theory of instantaneous power, the inverter reactive power can be regulated by changing the amplitude of its output voltage. In addition, the inverter active power can be adjusted by modifying the phase angle of its output voltage. Based on such theory, both the active power supply and the reactive power compensation (RPC) can be carried out simultaneously. When the insolation is weak or the PV modules are inoperative at night, the RPC feature of a PV system can still be used to improve the inverter utilisation factor. Some MATLAB simulation results are included here to show the feasibility of the method. (author)

  8. TS LOOP NON-POTABLE PUMP EVALUATION

    SciTech Connect (OSTI)

    S. Goodin

    1999-05-14T23:59:59.000Z

    This analysis evaluates the existing subsurface non-potable water system from the portal pump to the end of the water line in the South Ramp and determines if the pump size and spacing meets the system pressure and flow requirements for construction operations and incipient fire fighting capability as established in the Subsurface Fire Hazards Analysis (CRWMS M&O 1998b). This analysis does not address the non potable water system in the Cross Drift which is covered under a previous design analysis (CRWMS-M&O 1998a). The Subsurface Fire Hazards Analysis references sections of OSHA 29 CFR 1910 Subpart L for requirements applicable to the incipient fire fighting hose stations used underground. This analysis does not address mechanical system valves, fittings, risers and other components of the system piping. This system is not designed or intended to meet all National Fire Protection Association (NFPA) codes for a fire fighting system but is only considered a backup system to fire extinguishers that are installed throughout the Topopah Springs (TS) Loop and may be used to fight small incipient stage fires.

  9. ENERGIA DEL SOL Ts = 5780 K

    E-Print Network [OSTI]

    Batiste, Oriol

    ENERGIA DEL SOL Ts = 5780 K P = 3, 86 � 1026 W Constant solar = 1377 W/m2 4H1 + 2e- He4 + 2 utilitzar per a aprofitar l'energia solar. #12;LA RADIACI´O SOLAR #12;LA RADIACI´O SOLAR #12;#12;#12;LA;APROFITAMENT DE LA RADIACI´O SOLAR La radiaci´o solar la podem convertir en altres formes d'energia per

  10. Conservation of reactive electromagnetic energy in reactive time

    E-Print Network [OSTI]

    Kaiser, Gerald

    2015-01-01T23:59:59.000Z

    The complex Poynting theorem (CPT) is extended to a canonical time-scale domain $(t,s)$. Time-harmonic phasors are replaced by the positive-frequency parts of general fields, which extend analytically to complex time $t+is$, with $s>0$ interpreted as a time resolution scale. The real part of the extended CPT gives conservation in $t$ of a time-averaged field energy, and its imaginary part gives conservation in $s$ of a time-averaged reactive energy. In both cases, the averaging windows are determined by a Cauchy kernel of width $\\Delta t\\sim \\pm s$. This completes the time-harmonic CPT, whose imaginary part is generally supposed to be vaguely `related to' reactive energy without giving a conservation law, or even an expression, for the latter. The interpretation of $s$ as reactive time, tracking the leads and lags associated with stored capacitative and inductive energy, gives a simple explanation of the volt-ampere reactive (var) unit measuring reactive power: a var is simply one Joule per reactive second. T...

  11. Hybrid vehicle turbine engine technology support (HVTE-TS) project. 1995--1996 annual report

    SciTech Connect (OSTI)

    NONE

    1996-12-31T23:59:59.000Z

    This report presents a summary of technical work accomplished on the Hybrid Vehicle Turbine Engine--Technology Support (HVTE-TS) Project during calendar years 1995 and 1996. Work was performed under an initial National Aeronautics and Space Administration (NASA) contract DEN3-336. As of September 1996 the contract administration was transferred to the US Department of Energy (DoE) Chicago Operations Office, and renumbered as DE-AC02-96EE50553. The purpose of the HVTE-TS program is to develop gas turbine engine technology in support of DoE and automotive industry programs exploring the use of gas turbine generator sets in hybrid-electric automotive propulsion systems. The program focus is directed to the development of four key technologies to be applied to advanced turbogenerators for hybrid vehicles: Structural ceramic materials and processes; Low emissions combustion systems; Regenerators and seals systems; and Insulation systems and processes. 60 figs., 9 tabs.

  12. Genizah MS T-S AS 18.200

    E-Print Network [OSTI]

    Unknown

    2010-12-07T23:59:59.000Z

    *k T-S AS 18.200 *t Philosophy *s 6.7 x 7.3; 5 lines *m Paper; 1 leaf; badly torn, rubbed, stained *l Judaeo-Arabic *c Philosophical work, mentioning accidents. *e...

  13. Reactive Maintenance

    Broader source: Energy.gov [DOE]

    Reactive maintenance follows a run-it-until-it-breaks strategy where no actions or efforts are taken to maintain equipment as intended by the manufacturer. Studies indicate this is still the predominant mode of maintenance for Federal facilities.

  14. Reactive Power Compensator.

    DOE Patents [OSTI]

    El-Sharkawi, M.A.; Venkata, S.S.; Chen, M.; Andexler, G.; Huang, T.

    1992-07-28T23:59:59.000Z

    A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation. 26 figs.

  15. Reactive power compensator

    DOE Patents [OSTI]

    El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Woodinville, WA); Chen, Mingliang (Kirkland, WA); Andexler, George (Everett, WA); Huang, Tony (Seattle, WA)

    1992-01-01T23:59:59.000Z

    A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

  16. Edge Thomson scattering diagnostic on COMPASS tokamak: Installation, calibration, operation, improvements

    SciTech Connect (OSTI)

    Bohm, P., E-mail: bohm@ipp.cas.cz; Bilkova, P.; Melich, R.; Sestak, D.; Weinzettl, V.; Stockel, J.; Hron, M.; Panek, R. [Institute of Plasma Physics ASCR, Za Slovankou 1782/3, 18200 Prague (Czech Republic); Aftanas, M.; Stefanikova, E.; Janky, F.; Havlicek, J. [Institute of Plasma Physics ASCR, Za Slovankou 1782/3, 18200 Prague (Czech Republic); Faculty of Mathematics and Physics, Charles University in Prague, Ke Karlovu 3, 121 16 Prague (Czech Republic); Mikulin, O. [Institute of Plasma Physics ASCR, Za Slovankou 1782/3, 18200 Prague (Czech Republic); Faculty of Nuclear Sciences and Physical Engineering, Czech Technical University, Brehova 7, 11519 Prague (Czech Republic); Scannell, R.; Naylor, G. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Frassinetti, L. [School of Electrical Engineering, Division of Fusion Plasma Physics, KTH Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Fassina, A. [Consorzio RFX, Corso Stati Uniti, 4-35127 Padua (Italy); Walsh, M. J. [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St Paul lez Durance (France)

    2014-11-15T23:59:59.000Z

    The core Thomson scattering diagnostic (TS) on the COMPASS tokamak was put in operation and reported earlier. Implementation of edge TS, with spatial resolution along the laser beam up to ?1/100 of the tokamak minor radius, is presented now. The procedure for spatial calibration and alignment of both core and edge systems is described. Several further upgrades of the TS system, like a triggering unit and piezo motor driven vacuum window shutter, are introduced as well. The edge TS system, together with the core TS, is now in routine operation and provides electron temperature and density profiles.

  17. TERMS AND CONDITIONS OF RESIDENCE ("the Ts &Cs")

    E-Print Network [OSTI]

    Applebaum, David

    as a result of government legislation, this Agreement cannot be changed without prior written agreement in the glossary at the end of these Ts & Cs. 1. OUR RESPONSIBILITIES 1.1 Services & facilities During the Period and fittings for water, gas (if applicable), electricity and water heating in

  18. Genizah MS T-S AS 70.261

    E-Print Network [OSTI]

    Unknown

    2010-12-07T23:59:59.000Z

    *k T-S AS 70.261 *t Bible translation (?) *s 5 x 8.9; 4 lines *m Vellum; 1 leaf; badly torn, holes, badly stained *l Judaeo-Arabic; Hebrew *c Text too damaged to identify, appears to be a Bible translation with Hebrew incipits *e...

  19. Genizah MS T-S AS 82.34

    E-Print Network [OSTI]

    Unknown

    2010-12-07T23:59:59.000Z

    *k T-S AS 82.34 *t Rabbinics *s 10.5 x 23.7 (1 leaf: 11.8); 7–8 lines + marginalia *m Paper; 2 leaves (bifolium); torn, holes, rubbed *l Hebrew; Judaeo-Arabic *c Masse?et Dere? Ere? 5:1-2 and 6:2-3 with Judaeo-Arabic and Hebrew marginal notes...

  20. Genizah MS T-S AS 91.564

    E-Print Network [OSTI]

    Unknown

    2010-12-07T23:59:59.000Z

    *k T-S AS 91.564 *t Unidentified *s 9.5 x 4.6; 8 lines (recto); 9 lines (verso) *m Paper; 1 leaf; torn, faded, badly stained *l Judaeo-Arabic *c Text too damaged to identify. *e Other small fragments of paper have stuck to the manuscript....

  1. Genizah MS T-S AS 96.95

    E-Print Network [OSTI]

    Unknown

    2010-12-07T23:59:59.000Z

    *k T-S AS 96.95 *t Unidentified *s 3.5 x 9.4; 1 line + marginalia (recto; verso is blank) *m Paper; 1 leaf; torn, holes, faded, stained *l Hebrew; Judaeo-Arabic *c Unidentified text in Hebrew with Judaeo-Arabic marginal notes; the name Abraham...

  2. TS Power Plant, Eureka County, Nevada

    SciTech Connect (OSTI)

    Peltier, R. [DTE Energy Services (United States)

    2008-10-15T23:59:59.000Z

    Not all coal-fired power plants are constructed by investor-owned utilities or independent power producers selling to wholesale markets. When Newmont Mining Corp. recognised that local power supplies were inadequate and too expensive to meet long-term electricity needs for its major gold- and copper-mining operations in northern Nevada, it built its own generation. What is more, Newmont's privately owned 200-MW net coal-fired plant features power plant technologies that will surely become industry standards. Newmont's investment in power and technology is also golden: the capital cost will be paid back in about eight years. 4 figs.

  3. A Tariff for Reactive Power

    SciTech Connect (OSTI)

    Kueck, John D [ORNL; Kirby, Brendan J [ORNL; Li, Fangxing [ORNL; Tufon, Christopher [Pacific Gas and Electric Company; Isemonger, Alan [California Independent System Operator

    2008-07-01T23:59:59.000Z

    Two kinds of power are required to operate an electric power system: real power, measured in watts, and reactive power, measured in volt-amperes reactive or VARs. Reactive power supply is one of a class of power system reliability services collectively known as ancillary services, and is essential for the reliable operation of the bulk power system. Reactive power flows when current leads or lags behind voltage. Typically, the current in a distribution system lags behind voltage because of inductive loads such as motors. Reactive power flow wastes energy and capacity and causes voltage droop. To correct lagging power flow, leading reactive power (current leading voltage) is supplied to bring the current into phase with voltage. When the current is in phase with voltage, there is a reduction in system losses, an increase in system capacity, and a rise in voltage. Reactive power can be supplied from either static or dynamic VAR sources. Static sources are typically transmission and distribution equipment, such as capacitors at substations, and their cost has historically been included in the revenue requirement of the transmission operator (TO), and recovered through cost-of-service rates. By contrast, dynamic sources are typically generators capable of producing variable levels of reactive power by automatically controlling the generator to regulate voltage. Transmission system devices such as synchronous condensers can also provide dynamic reactive power. A class of solid state devices (called flexible AC transmission system devices or FACTs) can provide dynamic reactive power. One specific device has the unfortunate name of static VAR compensator (SVC), where 'static' refers to the solid state nature of the device (it does not include rotating equipment) and not to the production of static reactive power. Dynamic sources at the distribution level, while more costly would be very useful in helping to regulate local voltage. Local voltage regulation would reduce system losses, increase circuit capacity, increase reliability, and improve efficiency. Reactive power is theoretically available from any inverter-based equipment such as photovoltaic (PV) systems, fuel cells, microturbines, and adjustable-speed drives. However, the installation is usually only economical if reactive power supply is considered during the design and construction phase. In this report, we find that if the inverters of PV systems or the generators of combined heat and power (CHP) systems were designed with capability to supply dynamic reactive power, they could do this quite economically. In fact, on an annualized basis, these inverters and generators may be able to supply dynamic reactive power for about $5 or $6 per kVAR. The savings from the local supply of dynamic reactive power would be in reduced losses, increased capacity, and decreased transmission congestion. The net savings are estimated to be about $7 per kVAR on an annualized basis for a hypothetical circuit. Thus the distribution company could economically purchase a dynamic reactive power service from customers for perhaps $6/kVAR. This practice would provide for better voltage regulation in the distribution system and would provide an alternate revenue source to help amortize the cost of PV and CHP installations. As distribution and transmission systems are operated under rising levels of stress, the value of local dynamic reactive supply is expected to grow. Also, large power inverters, in the range of 500 kW to 1 MW, are expected to decrease in cost as they become mass produced. This report provides one data point which shows that the local supply of dynamic reactive power is marginally profitable at present for a hypothetical circuit. We expect that the trends of growing power flow on the existing system and mass production of inverters for distributed energy devices will make the dynamic supply of reactive power from customers an integral component of economical and reliable system operation in the future.

  4. Reactive Gliosis Reactive Oxygen Species: Superoxide

    E-Print Network [OSTI]

    . By sensing the electric signals generated by other 3368 Reactive Gliosis #12;individuals, mormyrids are alsoReactive Gliosis Glial Scar Reactive Oxygen Species: Superoxide Anions Neuroinflammation motor output. Reafferent Control in Electric Communication Reafferent Control in Electric Communication

  5. Particle Swarm Optimization Based Reactive Power Optimization

    E-Print Network [OSTI]

    Sujin, P R; Linda, M Mary

    2010-01-01T23:59:59.000Z

    Reactive power plays an important role in supporting the real power transfer by maintaining voltage stability and system reliability. It is a critical element for a transmission operator to ensure the reliability of an electric system while minimizing the cost associated with it. The traditional objectives of reactive power dispatch are focused on the technical side of reactive support such as minimization of transmission losses. Reactive power cost compensation to a generator is based on the incurred cost of its reactive power contribution less the cost of its obligation to support the active power delivery. In this paper an efficient Particle Swarm Optimization (PSO) based reactive power optimization approach is presented. The optimal reactive power dispatch problem is a nonlinear optimization problem with several constraints. The objective of the proposed PSO is to minimize the total support cost from generators and reactive compensators. It is achieved by maintaining the whole system power loss as minimum...

  6. Fuel Temperature Coefficient of Reactivity

    SciTech Connect (OSTI)

    Loewe, W.E.

    2001-07-31T23:59:59.000Z

    A method for measuring the fuel temperature coefficient of reactivity in a heterogeneous nuclear reactor is presented. The method, which is used during normal operation, requires that calibrated control rods be oscillated in a special way at a high reactor power level. The value of the fuel temperature coefficient of reactivity is found from the measured flux responses to these oscillations. Application of the method in a Savannah River reactor charged with natural uranium is discussed.

  7. Advanced Turbine Technology Applications Project (ATTAP) and Hybrid Vehicle Turbine Engine Technology Support project (HVTE-TS): Final summary report

    SciTech Connect (OSTI)

    NONE

    1998-12-01T23:59:59.000Z

    This final technical report was prepared by Rolls-Royce Allison summarizing the multiyear activities of the Advanced Turbine Technology Applications Project (ATTAP) and the Hybrid Vehicle Turbine Engine Technology Support (HVTE-TS) project. The ATTAP program was initiated in October 1987 and continued through 1993 under sponsorship of the US Department of Energy (DOE), Energy Conservation and Renewable Energy, Office of Transportation Technologies, Propulsion Systems, Advanced Propulsion Division. ATTAP was intended to advance the technological readiness of the automotive ceramic gas turbine engine. The target application was the prime power unit coupled to conventional transmissions and powertrains. During the early 1990s, hybrid electric powered automotive propulsion systems became the focus of development and demonstration efforts by the US auto industry and the Department of energy. Thus in 1994, the original ATTAP technology focus was redirected to meet the needs of advanced gas turbine electric generator sets. As a result, the program was restructured to provide the required hybrid vehicle turbine engine technology support and the project renamed HVTE-TS. The overall objective of the combined ATTAP and HVTE-TS projects was to develop and demonstrate structural ceramic components that have the potential for competitive automotive engine life cycle cost and for operating 3,500 hr in an advanced high temperature turbine engine environment. This report describes materials characterization and ceramic component development, ceramic components, hot gasifier rig testing, test-bed engine testing, combustion development, insulation development, and regenerator system development. 130 figs., 12 tabs.

  8. Search for the Heliospheric Termination Shock (TS) and Heliosheath (HS)

    SciTech Connect (OSTI)

    Ness, Norman F. [Bartol Research Institute, University of Delaware, Newark, DE 19716 (United States); Burlaga, Leonard F.; Acuna, Mario H. [NASA-Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Stone, Edward C. [California Institute of Technology, Pasadena, CA 91109 (United States); McDonald, Frank B. [Institute for Physical Science and Technology, University of Maryland, College Park, MD 20742 (United States)

    2005-08-01T23:59:59.000Z

    Voyager 1 continues to measure the very distant Heliospheric Magnetic Field (HMF) beyond 95 AU at {approx}35 North latitude. The MAG instrument data covers more than a full 22 years solar magnetic cycle. The magnitude of the observed HMF is well described, on average, by Parker's Archimedean spiral structure if due account is made for time variations of the source field strength and solar wind velocity. The V1 magnetic field observations do not provide any evidence for a field increase associated with entry into a subsonic solar wind region, such as the heliosheath is expected to be, nor an exit from this regime. We see no evidence for crossing of the Termination Shock (TS) as has been reported at {approx}85 AU by the LECP instrument. Merged Interaction Regions are identified by an increased HMF and associated decreases in the flux of >70 MeV/nuc cosmic rays which are then followed by a flux recovery. This CR-B relationship has been identified in V1 data and studied since 1982 when V1 was at 11 AU. The variance of HMF, a direct measure of the energy**1/2 in the HMF fluctuations, shows no significant changes associated with the alleged TS crossings in 2002-2003. Thus, the absence of any HMF increase at the entry into the heliosheath appears not to be due to the onset of mesoscale turbulence as proposed by Fisk. The TS has yet to be directly observed in-situ by the V1 MAG experiment in data through 2003.

  9. REAC/TS Radiation Accident Registry: An Overview

    SciTech Connect (OSTI)

    Doran M. Christensen, DO, REAC /TS Associate Director and Staff Physician Becky Murdock, REAC/TS Registry and Health Physics Technician

    2012-12-12T23:59:59.000Z

    Over the past four years, REAC/TS has presented a number of case reports from its Radiation Accident Registry. Victims of radiological or nuclear incidents must meet certain dose criteria for an incident to be categorized as an “accident” and be included in the registry. Although the greatest numbers of “accidents” in the United States that have been entered into the registry involve radiation devices, the greater percentage of serious accidents have involved sealed sources of one kind or another. But if one looks at the kinds of accident scenarios that have resulted in extreme consequence, i.e., death, the greater share of deaths has occurred in medical settings.

  10. Salvaging Timber: Landowner Do's and Don'ts

    E-Print Network [OSTI]

    Taylor, Eric; Foster, C. Darwin

    2005-10-19T23:59:59.000Z

    ER-037 5-06 Salvaging Timber: Landowner Do?s and Don?ts Eric L. Taylor, Assistant Professor and Extension Specialist, and C. Darwin Foster, Associate Department Head and Extension Program Leader for Forestry, The Texas A&M University System... A forester will help you make management decisions regarding your timber, such as whether or not to harvest (salvage) damaged timber. A forester can also help estimate the value of lost timber for tax purposes. See publication ER-038, ?Selecting a...

  11. G. M. Fikhtengol'ts, Course of Differential and Integral Calculus

    E-Print Network [OSTI]

    2005-01-07T23:59:59.000Z

    5. 6. G. M. Fikhtengol'ts, Course of Differential and Integral Calculus [in Russian], Vol. I,. Nauka, Moscow (]966), p. 608. P. Hartman, Ordinary Differential ...

  12. Guidance Document Reactive Chemicals

    E-Print Network [OSTI]

    showers and chillers. Health Hazards: The reactive chemicals are grouped primarily because of the physical

  13. FIELD TEST INSTRUCTION 100-NR-2 OPERABLE UNIT DESIGN OPTIMIZATION STUDY FOR SEQUESTRATION OF SR-90 SATURATED ZONE APATITE PERMEABLE REACTIVE BARRIER EXTENSION

    SciTech Connect (OSTI)

    BOWLES NA

    2010-10-06T23:59:59.000Z

    The objective of this field test instruction is to provide technical guidance for aqueous injection emplacement of an extension apatite permeable reactive barrier (PRE) for the sequestration of strontium-90 (Sr-90) using a high concentration amendment formulation. These field activities will be conducted according to the guidelines established in DOE/RL-2010-29, 100-NR-2 Design Optimization Study, hereafter referred to as the DOS. The DOS supports the Federal Facility Agreement Consent Order (EPA et al., 1989), Milestone M-16-06-01, and 'Complete Construction of a Permeable Reactive Barrier at 100-N.' Injections of apatite precursor chemicals will occur at an equal distance intervals on each end of the existing PRE to extend the PRB from the existing 91 m (300 ft) to at least 274 m (900 ft). Field testing at the 100-N Area Apatite Treatability Test Site, as depicted on Figure 1, shows that the barrier is categorized by two general hydrologic conceptual models based on overall well capacity and contrast between the Hanford and Ringold hydraulic conductivities. The upstream portion of the original barrier, shown on Figure 1, is characterized by relatively low overall well specific capacity. This is estimated from well development data and a lower contrast in hydraulic conductivity between the Hanford formation and Ringold Formations. Comparison of test results from these two locations indicate that permeability contrast between the Hanford formation and Ringold Formation is significantly less over the upstream one-third of the barrier. The estimated hydraulic conductivity for the Hanford formation and Ringold Formation over the upstream portion of the barrier based on observations during emplacement of the existing 91 m (300 ft) PRB is approximately 12 and 10 m/day (39 and 32 ft/day), respectively (PNNL-17429). However, these estimates should be used as a rough guideline only, as significant variability in hydraulic conductivity is likely to be observed in the barrier extension wells, particularly those in the Ringold formation. The downstream portion of the original barrier, shown on Figure 1, is characterized by generally higher well specific capacity and a larger hydraulic conductivity contrast between the Hanford formation and Ringold Formation. Hydraulic conductivity rates for the Hanford formation and Ringold Formation over the downstream portion of the barrier were estimated at 29 and 9 m/day (95 and 29 ft/day), respectively (with the Hanford formation hydraulic conductivity being greater in the downstream portion than the upstream portion). Once again, it should be noted that the actual conductivities may vary significantly, and the values state above should only be used as a rough initial estimates. Optimum apatite emplacement has been shown to occur when injections targeting the Hanford formation and the Ringold Formation are performed separately. The remainder of this test instruction provides details for conducting these formation-targeted injections.

  14. TS-05: 150 lines of Java with High Architectural Complexity Henrik Brbak Christensen

    E-Print Network [OSTI]

    Christensen, Henrik Bærbak

    choice. 2. TS-05 The motivational context of TS-05 is process control in a chem- ical plant or nuclear reactor system. The plant contains numerous sensors that measure values and monitors that display to implement a sensor reading broadcast. This approach represents a design proposal "by-the-book" from

  15. System for reactivating catalysts

    DOE Patents [OSTI]

    Ginosar, Daniel M. (Idaho Falls, ID); Thompson, David N. (Idaho Falls, ID); Anderson, Raymond P. (Idaho Falls, ID)

    2010-03-02T23:59:59.000Z

    A method of reactivating a catalyst, such as a solid catalyst or a liquid catalyst is provided. The method comprises providing a catalyst that is at least partially deactivated by fouling agents. The catalyst is contacted with a fluid reactivating agent that is at or above a critical point of the fluid reactivating agent and is of sufficient density to dissolve impurities. The fluid reactivating agent reacts with at least one fouling agent, releasing the at least one fouling agent from the catalyst. The at least one fouling agent becomes dissolved in the fluid reactivating agent and is subsequently separated or removed from the fluid reactivating agent so that the fluid reactivating agent may be reused. A system for reactivating a catalyst is also disclosed.

  16. Dynamic Reactive Power Control of Isolated Power Systems

    E-Print Network [OSTI]

    Falahi, Milad

    2012-10-03T23:59:59.000Z

    This dissertation presents dynamic reactive power control of isolated power systems. Isolated systems include MicroGrids in islanded mode, shipboard power systems operating offshore, or any other power system operating in islanded mode intentionally...

  17. Jefferson Lab Vehicle Fleet Do's and Don'ts | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Jefferson Lab Vehicle Fleet Do's and Don'ts In addition to safe driving, Jefferson Lab Fleet vehicle drivers are responsible for the proper use, maintenance and protection of their...

  18. Solderability Study of RABiTS-Based YBCO Coated Conductors

    SciTech Connect (OSTI)

    Zhang, Yifei [ORNL; Duckworth, Robert C [ORNL; Ha, Tam T [ORNL; Gouge, Michael J [ORNL

    2011-01-01T23:59:59.000Z

    The solderability of commercially available YBa{sub 2}Cu{sub 3}O{sub 7-x} (YBCO) coated conductors that were made from Rolling Assisted Biaxially Textured Substrates (RABiTS)-based templates was studied. The coated conductors, also known as second-generation (2G) high temperature superconductor (HTS) wires (in the geometry of flat tapes about 4 mm wide), were laminated with copper, brass, or stainless steel strips as stabilizers. To understand the factors that influence their solderability, surface profilometry and scanning electron microscopy were used to characterize the wire surfaces. The solderability of three solders, 52In48Sn, 67Bi33In, and 100In (wt.%), was evaluated using a standard test (IPC/ECA J-STD-002) and with two different commercial fluxes. It was found that the solderability varied with the solder and flux but the three different wires showed similar solderability for a fixed combination of solder and flux. Solder joints of the 2G wires were fabricated using the tools and the procedures recommended by the HTS wire manufacturer. The solder joints were made in a lap-joint geometry and with the superconducting sides of the two wires face-to-face. The electrical resistances of the solder joints were measured at 77 K, and the results were analyzed to qualify the soldering materials and evaluate the soldering process. It was concluded that although the selection of soldering materials affected the resistance of a solder joint, the resistivity of the stabilizer was the dominant factor.

  19. cnEiFrnr,:-BR,1;q*tsE ns John Franks

    E-Print Network [OSTI]

    Short, Daniel

    cnEiFrnr,:- BR,1;q*tsE ns Acid rain John Franks The liDk betwccn sulphur at|d dtrogen odde5 sofe.i,rc fro; th..f..ts torhesethe6xh6ustsofmiilionsol porlol of acid rain, little has been don. Acid rain was mntioned by Bdish chemistRobenAngus Smirhas a factor in lhe air a.ound Manchesterand 'cor

  20. Reactive power planning of large-scale systems

    SciTech Connect (OSTI)

    Burchett, R.C.; Happ, H.H.; Vierath, D.R.

    1983-01-01T23:59:59.000Z

    This paper discusses short-term operations planning applications in reactive power management involving existing equipment. Reactive power planning involves the sizing and siting of additional reactive support equipment in order to satisfy system voltage constraints (minimum and maximum limits) under both normal and contingency conditions. The use of the Optimal Power Flow (OPF) and the VARPLAN computer codes for operations planning are examined. The OPF software can be used to determine if reactive outputs from nearby generators are scheduled properly, and to confirm that parallel transformers have been properly set. A major benefit of the system planning software VARPLAN is the ability to simultaneously consider both normal and contingency conditions, while adding a minimal amount of new reactive power. Applications to long-term system planning of new reactive power sources are described.

  1. Real-WoRld Technology TesTs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electric submersible pumps (ESPs) are a versatile means of artificial lift used in oil and water wells. A drawback to an ESP installation is that it is a complex operation with...

  2. Test Pile Reactivity Loss Due to Trichloroethylene

    SciTech Connect (OSTI)

    Plumlee, K.E.

    2001-03-09T23:59:59.000Z

    The presence of trichloroethylene in the test pile caused a continual decrease in pile reactivity. A system which removed, purified, and returned 12,000 cfh helium to the pile has held contamination to a negligible level and has permitted normal pile operation.

  3. The dos and don'ts of distillation column control Sigurd Skogestad*

    E-Print Network [OSTI]

    Skogestad, Sigurd

    The dos and don'ts of distillation column control Sigurd Skogestad* Department of Chemical discusses distillation column control within the general framework of plantwide control. In addition for distillation columns. The standard LV-configuration combined with a fast temperature loop is recommended

  4. THE UNIVERSITY OF BRITISHCOLUMBIA U-B-TS -I 1 e -. . ...

    E-Print Network [OSTI]

    Farrell, Anthony P.

    I f THE UNIVERSITY OF BRITISHCOLUMBIA U-B-TS - I 1 e - . . ... w Find UBC Reports on the Web at www.external-affairs.ubc.ca/paweb/reports begins an. 31 and continues 3 April 4. Lectures take lace at 8:15p.m.in ecture Hall 2 of the Joodward

  5. Slant Transform Watermarking for Digital Images Anthony T.S. Ho, Xunzhan Zhu, Jun Shen

    E-Print Network [OSTI]

    Doran, Simon J.

    Slant Transform Watermarking for Digital Images Anthony T.S. Ho, Xunzhan Zhu, Jun Shen School transform for the copyright protection of images. Our earlier research work associated with the fast Hadamard transform for robust watermark embedding and retrieval of images and characters suggests

  6. TS-IDS Algorithm For Query Selection in the Deep Web Crawling

    E-Print Network [OSTI]

    Lu, Jianguo

    TS-IDS Algorithm For Query Selection in the Deep Web Crawling Yan Wang1 , Jianguo Lu2 , and Jessica. The deep web crawling is the process of collecting data items inside a data source hidden behind searchable of documents and terms involved, calls for new approximation algorithms for efficient deep web data crawling

  7. INHERENT WATER OPTICAL PROPERTIES AT THE CARIBBEAN TIME SERIES STATION (CaTS)

    E-Print Network [OSTI]

    Gilbes, Fernando

    INHERENT WATER OPTICAL PROPERTIES AT THE CARIBBEAN TIME SERIES STATION (CaTS) Fernando Gilbes Rico 00681 ABSTRACT The temporal variability of the inherent water optical properties at the Caribbean wavelengths, but in all cases, the values were less than one. The correlation between bio-optical properties

  8. Progress on the Frequency Agile Solar Radiotelescope T.S. Bastian

    E-Print Network [OSTI]

    : coronal magnetography, solar ares and particle acceleration, drivers of space weather, and the thermal the thermal structure and dynamics of the solar chromosphere. In addition to its priority mission as a basicProgress on the Frequency Agile Solar Radiotelescope T.S. Bastian National Radio Astronomy

  9. FEATURE ARTICLE T.S. Zhao, Y.S. Li, S.Y. Shen

    E-Print Network [OSTI]

    Zhao, Tianshou

    FEATURE ARTICLE T.S. Zhao, Y.S. Li, S.Y. Shen Anion-exchange membrane direct ethanol fuel cells Direct ethanol fuel cells (DEFCs) are a promising carbon-neutral and sustainable power source strategies to overcome them. Keywords fuel cell, direct ethanol fuel cells, anion- exchange membrane, ethanol

  10. Upper ocean T-S variations in the Greenland Sea and their association to climatic conditions

    E-Print Network [OSTI]

    Upper ocean T-S variations in the Greenland Sea and their association to climatic conditions Sirpa that the salinity variability in the central Greenland Gyre follows closely the sea level pressure (SLP) fluctuations found along the Greenland Coast, e.g., at Angmagssalik. Corresponding large-scale SLP field

  11. A novel electrode architecture for passive direct methanol fuel cells R. Chen, T.S. Zhao *

    E-Print Network [OSTI]

    Zhao, Tianshou

    A novel electrode architecture for passive direct methanol fuel cells R. Chen, T.S. Zhao 6 November 2006 Abstract The supply of cathode reactants in a passive direct methanol fuel cell: Fuel cell; Passive DMFC; Metal foam; Mass transfer resistance; Cell performance; Oxygen transport 1

  12. On the importance of minding ones Ps and Ts: metamorphic processes and quantitative petrology

    E-Print Network [OSTI]

    Sandiford, Mike

    On the importance of minding oneÕs Ps and Ts: metamorphic processes and quantitative petrology M. BROWN,1 R. W. WHITE2 AND M. SANDIFORD3 1 Laboratory for Crustal Petrology, Department of Geology phase equilibria studies. However, RogerÕs contributions to metamorphic petrology go well beyond

  13. Power Factor Reactive Power

    E-Print Network [OSTI]

    motor power: 117.7 V x 5.1 A = 600 W? = 0.6 kW? NOT the power measured by meter #12;Page 9 PSERC: displacement power factor: angle between voltage and current = 0 degrees pf = cos(0 degrees) = 1.0 true powerPage 1 PSERC Power Factor and Reactive Power Ward Jewell Wichita State University Power Systems

  14. Reactive power compensating system

    DOE Patents [OSTI]

    Williams, Timothy J. (Redondo Beach, CA); El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Seattle, WA)

    1987-01-01T23:59:59.000Z

    The reactive power of an induction machine is compensated by providing fixed capacitors on each phase line for the minimum compensation required, sensing the current on one line at the time its voltage crosses zero to determine the actual compensation required for each phase, and selecting switched capacitors on each line to provide the balance of the compensation required.

  15. Reactive Power Compensating System.

    DOE Patents [OSTI]

    Williams, Timothy J.; El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.

    1985-01-04T23:59:59.000Z

    The circuit was designed for the specific application of wind-driven induction generators. It has great potential for application in any situation where a varying reactive power load is present, such as with induction motors or generators, or for transmission network compensation.

  16. High critical current YBCO films prepared by an MOD process on RABiTS templates.

    SciTech Connect (OSTI)

    Li, X.; Rupich, M. W.; Kodenkandath, T.; Huang, Y.; Zhang, W.; Siegel, E.; Verebelyi, D. T.; Schoop, U.; Nguyen, N.; Thieme, C.; Chen, Z.; Feldman, D. M.; Larbalestier, D. C.; Holesinger, T. G.; Civale, L.; Jia, Q. X.; Maroni, A.; Rane, M. V.; Chemical Engineering; American Superconductor Corp.; Univ. of Wisconsin; LANL; State Univ. of New York

    2007-06-01T23:59:59.000Z

    The metal organic deposition (MOD) of YBCO high temperature superconducting films on RABiTS (rolling assisted biaxially textured substrates) templates has been developed at American Superconductor as a low-cost, scalable manufacturing process for the commercialization of the second generation (2G) HTS wire. The MOD process is based on the deposition of a triflu-oroacetate (TFA) based metal organic precursor film which is converted, in an ex-situ process, to the superconducting YBCO film. A major goal of the development has been achieving high critical currents. This paper reports the preparation and characterization of MOD-YBCO films with critical currents exceeding 500 A/cm-w (77 K, self-field) using a scaleable thick film approach on RABiTS templates. The high critical current films were obtained through optimization of the precursor composition, nucleation and growth conditions. The through-thickness dependence of the critical current density of MOD Alms as a function of film thickness and a correlation of the through-thickness transport properties and microstructure of the thick MOD/RABiTS samples is reported.

  17. Reactive Air Aluminization

    SciTech Connect (OSTI)

    Choi, Jung-Pyung; Chou, Y. S.; Stevenson, Jeffry W.

    2011-10-28T23:59:59.000Z

    Ferritic stainless steels and other alloys are of great interest to SOFC developers for applications such as interconnects, cell frames, and balance of plant components. While these alloys offer significant advantages (e.g., low material and manufacturing cost, high thermal conductivity, and high temperature oxidation resistance), there are challenges which can hinder their utilization in SOFC systems; these challenges include Cr volatility and reactivity with glass seals. To overcome these challenges, protective coatings and surface treatments for the alloys are under development. In particular, aluminization of alloy surfaces offers the potential for mitigating both evaporation of Cr from the alloy surface and reaction of alloy constituents with glass seals. Commercial aluminization processes are available to SOFC developers, but they tend to be costly due to their use of exotic raw materials and/or processing conditions. As an alternative, PNNL has developed Reactive Air Aluminization (RAA), which offers a low-cost, simpler alternative to conventional aluminization methods.

  18. JOINTLY HYPONORMAL PAIRS OF COMMUTING SUBNORMAL OPERATORS NEED NOT BE JOINTLY SUBNORMAL

    E-Print Network [OSTI]

    Curto, Raúl

    JOINTLY HYPONORMAL PAIRS OF COMMUTING SUBNORMAL OPERATORS NEED NOT BE JOINTLY SUBNORMAL RA´UL E operators, jointly hyponormal but not admitting commuting normal extensions. Each such family can be used] := ST - TS. We say that an n-tuple T = (T1, · · · , Tn) of operators on H is (jointly) hyponormal

  19. ssss ts t ts ss

    E-Print Network [OSTI]

    Chen, Tsuhan

    PLACE STEVENSON ROAD HUNGERFORDHILLROAD GAMEFARMROAD GAMEFARMROAD DRYDEN ROAD NYS ROUTE 366 EASTPALMROAD PALMROAD DRYDEN ROAD Equine Annex Complex Embryo Transfer Shed Newman Barn 'A' Poultry Building 'W' Poultry FORESTHOMEDRIVE MCINTYRE PLACE PLANTATIONS ROAD NYS ROUTE 392 FO REST HO M E DRIVE TOWER ROAD SAGEAVENUE

  20. PAPER ACCEPTED TO IEEE TRANSACTIONS ON POWER SYSTEMS, Nov. 2008 1 Reactive Power and Voltage Control in Distribution

    E-Print Network [OSTI]

    Cañizares, Claudio A.

    PAPER ACCEPTED TO IEEE TRANSACTIONS ON POWER SYSTEMS, Nov. 2008 1 Reactive Power and Voltage) problem associated with reactive power and voltage control in distribution systems to minimize daily--Distribution systems, reactive power control, voltage control, optimal switching operations, mixed integer nonlinear

  1. Abstract--This paper discusses various complex issues associated with reactive power management and pricing in the

    E-Print Network [OSTI]

    Cañizares, Claudio A.

    --Ancillary services, electricity markets, deregulation, reactive power management, system operation. I. INTRODUCTION, and recommended strengthening the reactive power and voltage control practices in all North American Electric, provision by the utilities of reactive power was embedded within the electricity supply to customers

  2. Application of the ''reactivity constraint approach'' to automatic reactor control

    SciTech Connect (OSTI)

    Bernard, J.A.; Henry, A.F.; Lanning, D.D.

    1988-02-01T23:59:59.000Z

    The ''reactivity constraint approach'' is described and demonstrated to be an effective and reliable means for the automatic control of power in nuclear reactors. This approach functions by restricting the effect of the delayed neutron populations to that which can be balanced by an induced change in the prompt population. This is done by limiting the net reactivity to the amount that can be offset by reversing the direction of motion of the automated control mechanism. The necessary reactivity constraints are obtained from the dynamic period equation, which gives the instantaneous reactor period as a function of the reactivity and the rate of change of reactivity. The derivation of this equation is described with emphasis on the recently obtained ''alternate'' formulation. Following a discussion of the behavior of each term of this alternate equation as a function of reactivity, its use in the design and operation of a nonlinear, closed-loop, digital controller for reactor power is in the design and operation of a nonlinear, closed-loop, digital controller for reactor power is described. Details of the initial experimental trials of the resulting controller are given.

  3. Second Generation HTs Wire Based on RABiTS Substrates and MOD YBCO

    SciTech Connect (OSTI)

    Schoop, U. [American Superconductor Corporation, Westborough, MA; Rupich, Marty [American Superconductor Corporation, Westborough, MA; Thieme, C. L. H. [American Superconductor Corporation, Westborough, MA; Verebelyi, D. T. [American Superconductor Corporation, Westborough, MA; Zhang, W. [American Superconductor Corporation, Westborough, MA; Li, Xiaoping [American Superconductor Corporation, Westborough, MA; Kodenkandath, Thomas [American Superconductor Corporation, Westborough, MA; Nguyen, N. [American Superconductor Corporation, Westborough, MA; Siegal, E. E. [American Superconductor Corporation, Westborough, MA; Civale, L. [Los Alamos National Laboratory (LANL); Holesinger, T. G. [Los Alamos National Laboratory (LANL); Maiorov, B. [Los Alamos National Laboratory (LANL); Goyal, Amit [ORNL; Paranthaman, Mariappan Parans [ORNL

    2005-01-01T23:59:59.000Z

    The performance of Second Generation (2G) high temperature superconducting wire manufactured by continuous reel-to-reel processes is nearing the 300 A/cm-width (77 K, self field) performance threshold for commercial power cable applications. The 2G manufacturing approach under development at American Superconductor is based on the combination of the RABiTS substrate-buffer technology with metal organic deposition (MOD) of the YBCO layer. The capability of this process has been demonstrated in multiple 10 meter lengths with critical currents exceeding 250 A/cm-width with high uniformity and reproducibility. Critical currents of 380 A/cm-width have been achieved in short length samples prepared by the same basic process. The incorporation of nanoparticles ('nanodots') into the YBCO layer using the MOD process has resulted in a 2-fold improvement in the critical current at 65 K in a 3 T field. The research and development focus at ASMC is now directed toward the economical scale-up of the RABiTS/MOD process, optimization of the conductor properties for targeted applications and the use of 2G wire in initial demonstration applications.

  4. NUCLEAR PLANT OPERATIONS AND

    E-Print Network [OSTI]

    Demazière, Christophe

    NUCLEAR PLANT OPERATIONS AND CONTROL KEYWORDS: moderator temper ature coefficient, reactivity co reactor Unit 4 of the Ringhals Nuclear Power Plant (Sweden) during fuel cycle 16 is analyzed absorption cross-section behavior. Consequently, if NUCLEAR TECHNOLOGY VOL. 140 NOV. 2002 147 #12;Demazière

  5. NUCLEAR PLANT OPERATIONS AND

    E-Print Network [OSTI]

    Pázsit, Imre

    NUCLEAR PLANT OPERATIONS AND CONTROL KEYWORDS: moderator temper- ature coefficient, reactivity co reactor Unit 4 of the Ringhals Nuclear Power Plant (Sweden) during fuel cycle 16 is analyzed. Consequently, if*E-mail: demaz@nephy.chalmers.se NUCLEAR TECHNOLOGY VOL. 140 NOV. 2002 147 #12;high-burnup fuel

  6. Effect of the cathode gas diffusion layer on the water transport behavior and the performance of passive direct methanol fuel cells operating with neat methanol

    E-Print Network [OSTI]

    Zhao, Tianshou

    of passive direct methanol fuel cells operating with neat methanol Q.X. Wu, T.S. Zhao , W.W. Yang Department Direct methanol fuel cell Passive operation Neat methanol operation a b s t r a c t The passive operation of a direct methanol fuel cell with neat methanol requires the water that is pro- duced at the cathode

  7. Electrocatalytic Reactivity for Oxygen Reduction of Palladium...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reactivity for Oxygen Reduction of Palladium-Modified Carbon Nanotubes Synthesized in Supercritical Fluid. Electrocatalytic Reactivity for Oxygen Reduction of Palladium-Modified...

  8. Formation, characterization and reactivity of adsorbed oxygen...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Formation, characterization and reactivity of adsorbed oxygen on BaOPt(111). Formation, characterization and reactivity of adsorbed oxygen on BaOPt(111). Abstract: The formation...

  9. ORNL/TM-2008/083 A Tariff for Reactive Power

    E-Print Network [OSTI]

    Pennycook, Steve

    ORNL/TM-2008/083 A Tariff for Reactive Power 2008 Prepared by Christopher Tufon, Pacific Gas & Electric Company Alan G. Isemonger, California Independent System Operator Brendan Kirby, ORNL, Knowledge and Transportation Science Division A Tariff for Reactive Power Christopher Tufon Alan G. Isemonger Brendan Kirby

  10. Mass transport phenomena in direct methanol fuel cells T.S. Zhao*, C. Xu, R. Chen, W.W. Yang

    E-Print Network [OSTI]

    Zhao, Tianshou

    Mass transport phenomena in direct methanol fuel cells T.S. Zhao*, C. Xu, R. Chen, W.W. Yang January 2009 Available online 20 February 2009 Keywords: Fuel cell Direct methanol fuel cell Mass cells ­ direct methanol fuel cells (DMFCs). We present a comprehensive review of the state

  11. Reaction mechanism of cumene hydroperoxide decomposition in cumene and evaluation of its reactivity hazards 

    E-Print Network [OSTI]

    Lu, Yuan

    2009-05-15T23:59:59.000Z

    understanding of the reaction mechanism. The slow progress in theoretical research hinders the application of the theoretical prediction in experimental research. For experimental research, the lack of integration of operational parameters into the reactivity...

  12. Reactive Ion Etch Users Guide

    E-Print Network [OSTI]

    Wager, John F.

    RIE Reactive Ion Etch Users Guide Eric Sundholm 2-22-2007 Standby Condition: be sure that the tool the chamber to remove any potential hazards before the chamber can be opened. 9. Pump Down Chamber Utilities Pump Chamber 10. Check pressure to start turbo pump Display Sensor Display a. Wait for pressure

  13. Estuaries Vol. 21, No. 2, p. 291-293 June 1998 Multiple T-S States for Estuaries, Shelves, and Marginal Seas

    E-Print Network [OSTI]

    Olver, Peter

    Estuaries Vol. 21, No. 2, p. 291-293 June 1998 Multiple T-S States for Estuaries, Shelves continental shelves ranges between O%Oand the ocean value of approximate- ly 35%0. Thus, worldwide

  14. Engine combustion control via fuel reactivity stratification

    DOE Patents [OSTI]

    Reitz, Rolf Deneys; Hanson, Reed M; Splitter, Derek A; Kokjohn, Sage L

    2013-12-31T23:59:59.000Z

    A compression ignition engine uses two or more fuel charges having two or more reactivities to control the timing and duration of combustion. In a preferred implementation, a lower-reactivity fuel charge is injected or otherwise introduced into the combustion chamber, preferably sufficiently early that it becomes at least substantially homogeneously dispersed within the chamber before a subsequent injection is made. One or more subsequent injections of higher-reactivity fuel charges are then made, and these preferably distribute the higher-reactivity matter within the lower-reactivity chamber space such that combustion begins in the higher-reactivity regions, and with the lower-reactivity regions following thereafter. By appropriately choose the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot).

  15. Mitochondrial reactive oxygen species and cancer

    E-Print Network [OSTI]

    Chandel, Navdeep S

    Mitochondria produce reactive oxygen species (mROS) as a natural by-product of electron transport chain activity. While initial studies focused on the damaging effects of reactive oxygen species, a recent paradigm shift ...

  16. Available online at www.sciencedirect.com Computers & Operations Research 32 (2005) 201217

    E-Print Network [OSTI]

    Gross, George

    , Rende (CS) 87036, Italy c University of Illinois at Urbana-Champaign, 1406 W. Green Street, Urbana, IL of optimally allocating his energy/capacity so as to maximize his proÿts. The multiplicity of auctions. Triki et al. / Computers & Operations Research 32 (2005) 201­217 energy price supply curve demand curve

  17. Author's personal copy Modeling of a passive DMFC operating with neat methanol

    E-Print Network [OSTI]

    Zhao, Tianshou

    Author's personal copy Modeling of a passive DMFC operating with neat methanol W.W. Yang, T.S. Zhao 2011 Keywords: Fuel cells Direct methanol fuel cells Neat methanol Mass transport Model a b s t r a c t A mathematical model is developed to simulate the fundamental transport phenomena in a passive direct methanol

  18. Abstract--Multi area power systems work most often with a poor inter-regional coordination about reactive power concerns.

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Abstract--Multi area power systems work most often with a poor inter-regional coordination about reactive power concerns. Transmission system operators typically do not possess a detailed knowledge about voltage profile across interconnected power systems. In this context, reactive power scheduling may

  19. Naturalistic Decision Making for Power System Operators

    SciTech Connect (OSTI)

    Greitzer, Frank L.; Podmore, Robin; Robinson, Marck; Ey, Pamela

    2010-02-01T23:59:59.000Z

    Motivation – Investigations of large-scale outages in the North American interconnected electric system often attribute the causes to three T’s: Trees, Training and Tools. To document and understand the mental processes used by expert operators when making critical decisions, a naturalistic decision making (NDM) model was developed. Transcripts of conversations were analyzed to reveal and assess NDM-based performance criteria. Findings/Design – An item analysis indicated that the operators’ Situation Awareness Levels, mental models, and mental simulations can be mapped at different points in the training scenario. This may identify improved training methods or analytical/ visualization tools. Originality/Value – This study applies for the first time, the concepts of Recognition Primed Decision Making, Situation Awareness Levels and Cognitive Task Analysis to training of electric power system operators. Take away message – The NDM approach provides a viable framework for systematic training management to accelerate learning in simulator-based training scenarios for power system operators and teams.

  20. Reactive composite compositions and mat barriers

    DOE Patents [OSTI]

    Langton, Christine A. (Aiken, SC); Narasimhan, Rajendran (Evans, GA); Karraker, David G. (Aiken, SC)

    2001-01-01T23:59:59.000Z

    A hazardous material storage area has a reactive multi-layer composite mat which lines an opening into which a reactive backfill and hazardous material are placed. A water-inhibiting cap may cover the hazardous material storage area. The reactive multi-layer composite mat has a backing onto which is placed an active layer which will neutralize or stabilize hazardous waste and a fronting layer so that the active layer is between the fronting and backing layers. The reactive backfill has a reactive agent which can stabilize or neutralize hazardous material and inhibit the movement of the hazardous material through the hazardous material storage area.

  1. Multiple steady states during reactive distillation of methyl tert-butyl ether

    SciTech Connect (OSTI)

    Nijhuis, S.A. (Univ. of Amsterdam (Netherlands). Chemical Engineering Dept.); Kerkhof, F.P.J.M.; Mak, A.N.S. (Comprimo Engineers and Contractors, Amsterdam (Netherlands))

    1993-11-01T23:59:59.000Z

    This paper presents results of computer simulations of the synthesis of methyl tert-butyl ether (MTBE) in a fixed-bed reactor and in a reactive distillation column. These calculations clearly showed the advantages of MTBE synthesis in a catalytic distillation tower. Furthermore, the computer simulations showed that multiple steady states may occur in the reactive distillation column during MTBE synthesis in a broad range of operating conditions. An analysis of some sensitivity studies is presented.

  2. Reactivity of Pb(II) at the Mn(III,IV) (Oxyhydr)Oxide-Water Interface

    E-Print Network [OSTI]

    Sparks, Donald L.

    , the reactivity of lead (Pb(II)) on naturally occurring Mn(III,IV) (oxyhydr)oxide minerals was evaluated using to suggest oxidation as an operative sorption mechanism. Lead appeared to coordinate to vacancy sitesReactivity of Pb(II) at the Mn(III,IV) (Oxyhydr)Oxide-Water Interface C H R I S T O P H E R J . M

  3. Options for Control of Reactive Power by Distributed Photovoltaic Generators

    E-Print Network [OSTI]

    Petr Sulc; Konstantin Turitsyn; Scott Backhaus; Michael Chertkov

    2010-08-04T23:59:59.000Z

    High penetration levels of distributed photovoltaic(PV) generation on an electrical distribution circuit present several challenges and opportunities for distribution utilities. Rapidly varying irradiance conditions may cause voltage sags and swells that cannot be compensated by slowly responding utility equipment resulting in a degradation of power quality. Although not permitted under current standards for interconnection of distributed generation, fast-reacting, VAR-capable PV inverters may provide the necessary reactive power injection or consumption to maintain voltage regulation under difficult transient conditions. As side benefit, the control of reactive power injection at each PV inverter provides an opportunity and a new tool for distribution utilities to optimize the performance of distribution circuits, e.g. by minimizing thermal losses. We discuss and compare via simulation various design options for control systems to manage the reactive power generated by these inverters. An important design decision that weighs on the speed and quality of communication required is whether the control should be centralized or distributed (i.e. local). In general, we find that local control schemes are capable for maintaining voltage within acceptable bounds. We consider the benefits of choosing different local variables on which to control and how the control system can be continuously tuned between robust voltage control, suitable for daytime operation when circuit conditions can change rapidly, and loss minimization better suited for nighttime operation.

  4. Layered reactive particles with controlled geometries, energies, and reactivities, and methods for making the same

    DOE Patents [OSTI]

    Fritz, Gregory M; Knepper, Robert Allen; Weihs, Timothy P; Gash, Alexander E; Sze, John S

    2013-04-30T23:59:59.000Z

    An energetic composite having a plurality of reactive particles each having a reactive multilayer construction formed by successively depositing reactive layers on a rod-shaped substrate having a longitudinal axis, dividing the reactive-layer-deposited rod-shaped substrate into a plurality of substantially uniform longitudinal segments, and removing the rod-shaped substrate from the longitudinal segments, so that the reactive particles have a controlled, substantially uniform, cylindrically curved or otherwise rod-contoured geometry which facilitates handling and improves its packing fraction, while the reactant multilayer construction controls the stability, reactivity and energy density of the energetic composite.

  5. Year GBClass Make Model M/M/Specs EmisStd City Hiwy Green Score 2014 01_TS AUDI TT ROADSTER QUATTRO 2.0L 4, auto Awd [P] ULEV II / Bin 5 22 31 42

    E-Print Network [OSTI]

    Derisi, Joseph

    Year GBClass Make Model M/M/Specs EmisStd City Hiwy Green Score 2014 01_TS MERCEDES-BENZ SMART FORTWO (CONVERTIBLE) 1.0L 3, auto [P] ULEV II / Bin 5 34 38 53 2014 01_TS MERCEDES-BENZ SMART FORTWO (COUPE) 1.0L 3, auto [P] ULEV II / Bin 5 34 38 53 2014 01_TS MERCEDES

  6. Permeable Reactive Barriers | Department of Energy

    Energy Savers [EERE]

    in the barrier, a chemical reaction occurs with the barrier material that results in adsorption, mineral precipitation, or degradation to a harmless compound. Reactive barriers...

  7. Rejuvenating Permeable Reactive Barriers by Chemical Flushing

    Broader source: Energy.gov [DOE]

    Final Report:Rejuvenating Permeable Reactive Barriers by Chemical Flushing,U.S. Environmental Protection Agency, Region 8 Support.August 2004

  8. UNDERGRADUATE FELLOWSHIP RECIPIENTS: Stephanie Freeman -Permanent Reactive

    E-Print Network [OSTI]

    Fay, Noah

    55 2003 UNDERGRADUATE FELLOWSHIP RECIPIENTS: Stephanie Freeman - Permanent Reactive Bio Engineering Andrew Hinnell - Improving Electrical Resistivity Tomography for Characterization of Non

  9. Comparison of Conventional Diesel and Reactivity Controlled...

    Broader source: Energy.gov (indexed) [DOE]

    DEER 10182012 Comparison of Conventional Diesel and Reactivity Controlled Compression Ignition (RCCI) Combustion in a Light-Duty Engine Rolf D. Reitz and Sage L. Kokjohn Engine...

  10. Characterization and Reactivity of Iron Nanoparticles Prepared...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    engineered remediation systems. However, the structural characteristics of the metal additives and mechanism responsible for changes in reactivity have not been fully elucidated....

  11. Exploring the reactivity of bacterial multicomponent monooxygenases

    E-Print Network [OSTI]

    Tinberg, Christine Elaine

    2010-01-01T23:59:59.000Z

    Chapter 1. Introduction: The Reactivity of Bacterial Multicomponent Monooxygenases Bacterial multicomponent monooxygenases constitute a remarkable family of enzymes that oxidize small, inert hydrocarbon substrates using ...

  12. Demonstration/Development of Reactivity Controlled Compression...

    Broader source: Energy.gov (indexed) [DOE]

    DemonstrationDevelopment of Reactivity Controlled Compression Ignition (RCCI) Combustion for High Efficiency, Low Emissions Vehicle Applications Dr. Rolf Reitz Wisconsin Engine...

  13. Effect of water concentration in the anode catalyst layer on the performance of direct methanol fuel cells operating

    E-Print Network [OSTI]

    Zhao, Tianshou

    Effect of water concentration in the anode catalyst layer on the performance of direct methanol fuel cells operating with neat methanol Q.X. Wu a , S.Y. Shen a , Y.L. He b , T.S. Zhao a cells Direct methanol fuel cells Neat methanol Water concentration a b s t r a c t This paper reports

  14. Method for reactivating catalysts and a method for recycling supercritical fluids used to reactivate the catalysts

    DOE Patents [OSTI]

    Ginosar, Daniel M. (Idaho Falls, ID); Thompson, David N. (Idaho Falls, ID); Anderson, Raymond P. (Idaho Falls, ID)

    2008-08-05T23:59:59.000Z

    A method of reactivating a catalyst, such as a solid catalyst or a liquid catalyst. The method comprises providing a catalyst that is at least partially deactivated by fouling agents. The catalyst is contacted with a fluid reactivating agent that is at or above a critical point of the fluid reactivating agent and is of sufficient density to dissolve impurities. The fluid reactivating agent reacts with at least one fouling agent, releasing the at least one fouling agent from the catalyst. The at least one fouling agent becomes dissolved in the fluid reactivating agent and is subsequently separated or removed from the fluid reactivating agent so that the fluid reactivating agent may be reused. A system for reactivating a catalyst is also disclosed.

  15. Reactive and non-reactive interactions of thiophene with WS2...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    interactions of thiophene with WS2 fullerene-like nanoparticles: an ultra-high vacuum surface Reactive and non-reactive interactions of thiophene with WS2 fullerene-like...

  16. Analysis of Reactivity Induced Accident for Control Rods Ejection with Loss of Cooling

    E-Print Network [OSTI]

    Hend Mohammed El Sayed Saad; Hesham Mohammed Mohammed Mansour; Moustafa Aziz Abd El Wahab

    2013-06-05T23:59:59.000Z

    Understanding of the time-dependent behavior of the neutron population in nuclear reactor in response to either a planned or unplanned change in the reactor conditions, is a great importance to the safe and reliable operation of the reactor. In the present work, the point kinetics equations are solved numerically using stiffness confinement method (SCM). The solution is applied to the kinetics equations in the presence of different types of reactivities and is compared with different analytical solutions. This method is also used to analyze reactivity induced accidents in two reactors. The first reactor is fueled by uranium and the second is fueled by plutonium. This analysis presents the effect of negative temperature feedback with the addition positive reactivity of control rods to overcome the occurrence of control rod ejection accident and damaging of the reactor. Both power and temperature pulse following the reactivity- initiated accidents are calculated. The results are compared with previous works and satisfactory agreement is found.

  17. Static reactive power compensators for high-voltage power systems. Final report

    SciTech Connect (OSTI)

    Not Available

    1981-04-01T23:59:59.000Z

    A study conducted to summarize the role of static reactive power compensators for high voltage power system applications is described. This information should be useful to the utility system planning engineer in applying static var systems (SVS) to high voltage as (HVAC) systems. The static var system is defined as a form of reactive power compensator. The general need for reactive power compensation in HVAC systems is discussed, and the static var system is compared to other devices utilized to provide reactive power compensation. Examples are presented of applying SVS for specific functions, such as the prevention of voltage collapse. The operating principles of commercially available SVS's are discussed in detail. The perormance and active power loss characteristics of SVS types are compared.

  18. Analysis of Reactivity Induced Accident for Control Rods Ejection with Loss of Cooling

    E-Print Network [OSTI]

    Saad, Hend Mohammed El Sayed; Wahab, Moustafa Aziz Abd El

    2013-01-01T23:59:59.000Z

    Understanding of the time-dependent behavior of the neutron population in nuclear reactor in response to either a planned or unplanned change in the reactor conditions, is a great importance to the safe and reliable operation of the reactor. In the present work, the point kinetics equations are solved numerically using stiffness confinement method (SCM). The solution is applied to the kinetics equations in the presence of different types of reactivities and is compared with different analytical solutions. This method is also used to analyze reactivity induced accidents in two reactors. The first reactor is fueled by uranium and the second is fueled by plutonium. This analysis presents the effect of negative temperature feedback with the addition positive reactivity of control rods to overcome the occurrence of control rod ejection accident and damaging of the reactor. Both power and temperature pulse following the reactivity- initiated accidents are calculated. The results are compared with previous works and...

  19. A Preliminary Analysis of the Economics of Using Distributed Energy as a Source of Reactive Power Supply

    SciTech Connect (OSTI)

    Li, Fangxing [ORNL; Kueck, John D [ORNL; Rizy, D Tom [ORNL; King, Thomas F [ORNL

    2006-04-01T23:59:59.000Z

    A major blackout affecting 50 million people in the Northeast United States, where insufficient reactive power supply was an issue, and an increased number of filings made to the Federal Energy Regulatory Commission by generators for reactive power has led to a closer look at reactive power supply and compensation. The Northeastern Massachusetts region is one such area where there is an insufficiency in reactive power compensation. Distributed energy due to its close proximity to loads seems to be a viable option for solving any present or future reactive power shortage problems. Industry experts believe that supplying reactive power from synchronized distributed energy sources can be 2 to 3 times more effective than providing reactive support in bulk from longer distances at the transmission or generation level. Several technology options are available to supply reactive power from distributed energy sources such as small generators, synchronous condensers, fuel cells or microturbines. In addition, simple payback analysis indicates that investments in DG to provide reactive power can be recouped in less than 5 years when capacity payments for providing reactive power are larger than $5,000/kVAR and the DG capital and installation costs are lower than $30/kVAR. However, the current institutional arrangements for reactive power compensation present a significant barrier to wider adoption of distributed energy as a source of reactive power. Furthermore, there is a significant difference between how generators and transmission owners/providers are compensated for reactive power supplied. The situation for distributed energy sources is even more difficult, as there are no arrangements to compensate independent DE owners interested in supplying reactive power to the grid other than those for very large IPPs. There are comparable functionality barriers as well, as these smaller devices do not have the control and communications requirements necessary for automatic operation in response to local or system operators. There are no known distributed energy asset owners currently receiving compensation for reactive power supply or capability. However, there are some cases where small generators on the generation and transmission side of electricity supply have been tested and have installed the capability to be dispatched for reactive power support. Several concerns need to be met for distributed energy to become widely integrated as a reactive power resource. The overall costs of retrofitting distributed energy devices to absorb or produce reactive power need to be reduced. There needs to be a mechanism in place for ISOs/RTOs to procure reactive power from the customer side of the meter where distributed energy resides. Novel compensation methods should be introduced to encourage the dispatch of dynamic resources close to areas with critical voltage issues. The next phase of this research will investigate in detail how different options of reactive power producing DE can compare both economically and functionally with shunt capacitor banks. Shunt capacitor banks, which are typically used for compensating reactive power consumption of loads on distribution systems, are very commonly used because they are very cost effective in terms of capital costs. However, capacitor banks can require extensive maintenance especially due to their exposure to lightning at the top of utility poles. Also, it can be problematic to find failed capacitor banks and their maintenance can be expensive, requiring crews and bucket trucks which often requires total replacement. Another shortcoming of capacitor banks is the fact that they usually have one size at a location (typically sized as 300, 600, 900 or 1200kVAr) and thus don't have variable range as do reactive power producing DE, and cannot respond to dynamic reactive power needs. Additional future work is to find a detailed methodology to identify the hidden benefit of DE for providing reactive power and the best way to allocate the benefit among customers, utilities, transmission companies or RTOs.

  20. Reactive Power Support Services in Electricity Markets

    E-Print Network [OSTI]

    Reactive Power Support Services in Electricity Markets Costing and Pricing of Ancillary Services Reactive Power Support Services in Electricity Markets Costing and Pricing of Ancillary Services Project this Project For information about this project contact: Peter W. Sauer, Project Leader Professor Electrical

  1. REACTIVE LOAD MODELINGIMPACTS ONNODAL PRICESINPOOL MODELELECTRICITYMARKETS

    E-Print Network [OSTI]

    Gross, George

    REACTIVE LOAD MODELINGIMPACTS ONNODAL PRICESINPOOL MODELELECTRICITYMARKETS EttoreBompard, Enrico of the nodal prices in competitive electricity markets based on the Pool paradigm. Such prices focus of the paper is on the explicit evaluation of the impactsof the reactive load onthenodal real

  2. REACTIVE ENVIRONMENTS AND AUGMENTED MEDIA SPACES

    E-Print Network [OSTI]

    Cooperstock, Jeremy R.

    REACTIVE ENVIRONMENTS AND AUGMENTED MEDIA SPACES by Jeremy R. Cooperstock A thesis submitted in conformity with the requirements for the degree of Doctor of Philosophy Graduate Department of Electrical and Computer Engineering University of Toronto © Copyright by Jeremy R. Cooperstock, 1996 #12;ii REACTIVE

  3. Reactivity Controlled Compression Ignition (RCCI) Combustion on a Multi-Cylinder Light-Duty Diesel Engine

    SciTech Connect (OSTI)

    Curran, Scott [ORNL; Hanson, Reed M [ORNL; Wagner, Robert M [ORNL

    2012-01-01T23:59:59.000Z

    Reactivity controlled compression ignition is a low-temperature combustion technique that has been shown, both in computational fluid dynamics modeling and single-cylinder experiments, to obtain diesel-like efficiency or better with ultra-low nitrogen oxide and soot emissions, while operating primarily on gasoline-like fuels. This paper investigates reactivity controlled compression ignition operation on a four-cylinder light-duty diesel engine with production-viable hardware using conventional gasoline and diesel fuel. Experimental results are presented over a wide speed and load range using a systematic approach for achieving successful steady-state reactivity controlled compression ignition combustion. The results demonstrated diesel-like efficiency or better over the operating range explored with low engine-out nitrogen oxide and soot emissions. A peak brake thermal efficiency of 39.0% was demonstrated for 2600 r/min and 6.9 bar brake mean effective pressure with nitrogen oxide emissions reduced by an order of magnitude compared to conventional diesel combustion operation. Reactivity controlled compression ignition emissions and efficiency results are compared to conventional diesel combustion operation on the same engine.

  4. Operations & Maintenance

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Operations and Maintenance Operations OASIS: OATI (Note: this site is not hosted by Western and requires a digital certificate and login for full access.) Contact Information...

  5. Operations & Maintenance

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rates Operations & Maintenance Operations OASIS: WACM (Note: this site is not hosted by Western and requires a digital certificate and login for full access.) wesTTrans Common...

  6. Reactive Support and Voltage Control Service: Key Issues and Challenges

    E-Print Network [OSTI]

    Gross, George

    reactive support and voltage control services. Keywords ­ Competitive Electricity Markets, Reactive PowerReactive Support and Voltage Control Service: Key Issues and Challenges George Gross^, Paolo Marannino° and Gianfranco Chicco* ^ Department of Electrical and Computer Engineering, University

  7. First unitarity-independent determination of the CKM matrix elements $V_{td}$, $V_{ts}$, and ${V_{tb}$ and the implications for unitarity

    E-Print Network [OSTI]

    John Swain; Lucas Taylor

    1997-12-17T23:59:59.000Z

    The magnitudes of the CKM matrix elements $V_{td}$, $V_{ts}$, and $V_{tb}$ are determined for the first time without any assumptions of unitarity. The implications for the unitarity of the CKM matrix as a whole are discussed.

  8. Submitted to special issue ChERD. This version revised 22 Nov. 2006 The dos and don'ts of distillation column control

    E-Print Network [OSTI]

    Skogestad, Sigurd

    'ts of distillation column control Sigurd Skogestad* Department of Chemical Engineering Norwegian University of Science and Technology N-7491 Trondheim, Norway Abstract The paper discusses distillation column control recommendations to assist the engineer in designing control systems for distillation columns. The standard LV

  9. PREDICTION OF REGIONAL WIND POWER T.S. Nielsen1, H. Madsen1, H. Aa. Nielsen1, L. Landberg2, G. Giebel2

    E-Print Network [OSTI]

    PREDICTION OF REGIONAL WIND POWER T.S. Nielsen1, H. Madsen1, H. Aa. Nielsen1, L. Landberg2, G, Denmark Tel: +45 4525 3428, Fax: +45 4588 2673, E-mail: tsn@imm.dtu.dk 2Department of Wind Energy Risø the total wind power production in a larger region based on a combination of on-line measurements of power

  10. A smoothed particle hydrodynamics model for reactive transport...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A smoothed particle hydrodynamics model for reactive transport and mineral precipitation in porous and fractured porous media. A smoothed particle hydrodynamics model for reactive...

  11. Assessment of Controlling Processes for Field-Scale Uranium Reactive...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    reactive transport model was employed to assess the key factors and processes that control the field-scale uranium reactive transport. Taking into consideration of relevant...

  12. Characterization of Dual-Fuel Reactivity Controlled Compression...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dual-Fuel Reactivity Controlled Compression Ignition (RCCI) Using Hydrated Ethanol and Diesel Fuel Characterization of Dual-Fuel Reactivity Controlled Compression Ignition (RCCI)...

  13. Field Demonstration Of Permeable Reactive Barriers To Remove

    E-Print Network [OSTI]

    Field Demonstration Of Permeable Reactive Barriers To Remove Dissolved Uranium From Groundwater-001 November 2000 FIELD DEMONSTRATION OF PERMEABLE REACTIVE BARRIERS TO REMOVE DISSOLVED URANIUM FROM

  14. Comparison of Conventional Diesel and Reactivity Controlled Compressio...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Conventional Diesel and Reactivity Controlled Compression Ignition (RCCI) Combustion in a Light-Duty Engine Comparison of Conventional Diesel and Reactivity Controlled Compression...

  15. Enrichment of Functional Redox Reactive Proteins and Identification...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Redox Reactive Proteins and Identification by Mass Spectrometry Results in Several Terminal Fe(III) Enrichment of Functional Redox Reactive Proteins and Identification by Mass...

  16. Microscopic Reactive Diffusion of Uranium in the Contaminated...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reactive Diffusion of Uranium in the Contaminated Sediments at Hanford, United States. Microscopic Reactive Diffusion of Uranium in the Contaminated Sediments at Hanford, United...

  17. Role of Point Defects on the Reactivity of Reconstructed Anatase...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Point Defects on the Reactivity of Reconstructed Anatase Titanium Dioxide (001) Surface. Role of Point Defects on the Reactivity of Reconstructed Anatase Titanium Dioxide (001)...

  18. Abstract--This paper proposes a novel heuristic algorithm that helps alleviate the need for integer variables in a reactive power

    E-Print Network [OSTI]

    Cañizares, Claudio A.

    integrated systems, the cost of reactive power was generally embedded within the electricity tariff, while for integer variables in a reactive power procurement model for an Independent System Operator in deregulated electricity markets. The heuristic scheme works on a three-step approach involving the calculation of marginal

  19. Gas chromatograph-mass spectrometer (GC/MS) system for quantitative analysis of reactive chemical compounds

    DOE Patents [OSTI]

    Grindstaff, Quirinus G. (Oak Ridge, TN)

    1992-01-01T23:59:59.000Z

    Described is a new gas chromatograph-mass spectrometer (GC/MS) system and method for quantitative analysis of reactive chemical compounds. All components of such a GC/MS system external to the oven of the gas chromatograph are programmably temperature controlled to operate at a volatilization temperature specific to the compound(s) sought to be separated and measured.

  20. Experimental investigation of piston heat transfer under conventional diesel and reactivity-controlled compression ignition combustion regimes

    SciTech Connect (OSTI)

    Splitter, Derek A [ORNL; Hendricks, Terry Lee [Sandia National Laboratories (SNL); Ghandhi, Jaal B [University of Wisconsin

    2014-01-01T23:59:59.000Z

    The piston of a heavy-duty single-cylinder research engine was instrumented with 11 fast-response surface thermocouples, and a commercial wireless telemetry system was used to transmit the signals from the moving piston. The raw thermocouple data were processed using an inverse heat conduction method that included Tikhonov regularization to recover transient heat flux. By applying symmetry, the data were compiled to provide time-resolved spatial maps of the piston heat flux and surface temperature. A detailed comparison was made between conventional diesel combustion and reactivity-controlled compression ignition combustion operations at matched conditions of load, speed, boost pressure, and combustion phasing. The integrated piston heat transfer was found to be 24% lower, and the mean surface temperature was 25 C lower for reactivity-controlled compression ignition operation as compared to conventional diesel combustion, in spite of the higher peak heat release rate. Lower integrated piston heat transfer for reactivity-controlled compression ignition was found over all the operating conditions tested. The results showed that increasing speed decreased the integrated heat transfer for conventional diesel combustion and reactivity-controlled compression ignition. The effect of the start of injection timing was found to strongly influence conventional diesel combustion heat flux, but had a negligible effect on reactivity-controlled compression ignition heat flux, even in the limit of near top dead center high-reactivity fuel injection timings. These results suggest that the role of the high-reactivity fuel injection does not significantly affect the thermal environment even though it is important for controlling the ignition timing and heat release rate shape. The integrated heat transfer and the dynamic surface heat flux were found to be insensitive to changes in boost pressure for both conventional diesel combustion and reactivity-controlled compression ignition. However, for reactivity-controlled compression ignition, the mean surface temperature increased with changes in boost suggesting that equivalence ratio affects steady-state heat transfer.

  1. Groundwater well with reactive filter pack

    DOE Patents [OSTI]

    Gilmore, Tyler J. (Pasco, WA); Holdren, Jr., George R. (Kennewick, WA); Kaplan, Daniel I. (Richland, WA)

    1998-01-01T23:59:59.000Z

    A method and apparatus for the remediation of contaminated soil and ground water wherein a reactive pack material is added to the annular fill material utilized in standard well construction techniques.

  2. A Tariff for Reactive Power - IEEE

    SciTech Connect (OSTI)

    Kueck, John D [ORNL; Tufon, Christopher [Pacific Gas and Electric Company; Isemonger, Alan [California Independent System Operator; Kirby, Brendan J [ORNL

    2008-11-01T23:59:59.000Z

    This paper describes a suggested tariff or payment for the local supply of reactive power from distributed energy resources. The authors consider four sample customers, and estimate the cost of supply of reactive power for each customer. The power system savings from the local supply of reactive power are also estimated for a hypothetical circuit. It is found that reactive power for local voltage regulation could be supplied to the distribution system economically by customers when new inverters are installed. The inverter would be supplied with a power factor of 0.8, and would be capable of local voltage regulation to a schedule supplied by the utility. Inverters are now installed with photovoltaic systems, fuel cells and microturbines, and adjustable-speed motor drives.

  3. Reactivity control assembly for nuclear reactor

    DOE Patents [OSTI]

    Bollinger, Lawrence R. (Schenectady, NY)

    1984-01-01T23:59:59.000Z

    Reactivity control assembly for nuclear reactor comprises supports stacked above reactor core for holding control rods. Couplers associated with the supports and a vertically movable drive shaft have lugs at their lower ends for engagement with the supports.

  4. Systematic approach for chemical reactivity evaluation

    E-Print Network [OSTI]

    Aldeeb, Abdulrehman Ahmed

    2004-09-30T23:59:59.000Z

    , to measure thermal reactivity of chemical systems. Studying all the various reaction pathways experimentally however is very expensive and time consuming. Therefore, it is essential to employ simplified screening tools and other methods to reduce the number...

  5. Groundwater well with reactive filter pack

    DOE Patents [OSTI]

    Gilmore, T.J.; Holdren, G.R. Jr.; Kaplan, D.I.

    1998-09-08T23:59:59.000Z

    A method and apparatus are disclosed for the remediation of contaminated soil and ground water wherein a reactive pack material is added to the annular fill material utilized in standard well construction techniques. 3 figs.

  6. EPA/ITRC-RTDF permeable reactive barrier short course. Permeable reactive barriers: Application and deployment

    SciTech Connect (OSTI)

    Not Available

    1999-01-01T23:59:59.000Z

    This report focuses on the following: Permeable Reactive Barriers: Application and Deployment; Introduction to Permeable Reactive Barriers (PRBs) for Remediating and Managing Contaminated Groundwater in Situ; Collection and Interpretation of Design Data 1: Site Characterization for PRBs; Reactive Materials: Zero-Valent Iron; Collection and Interpretation of Design Data 2: Laboratory and Pilot Scale Tests; Design Calculations; Compliance Monitoring, Performance Monitoring and Long-Term Maintenance for PRBs; PRB Emplacement Techniques; PRB Permitting and Implementation; Treatment of Metals; Non-Metallic Reactive Materials; Economic Considerations for PRB Deployment; and Bibliography.

  7. EPA/ITRC-RTDF permeable reactive barrier short course. Permeable reactive barriers: Application and deployment

    SciTech Connect (OSTI)

    NONE

    1999-11-01T23:59:59.000Z

    This report focuses on the following: Permeable Reactive Barriers: Application and Deployment; Introduction to Permeable Reactive Barriers (PRBs) for Remediating and Managing Contaminated Groundwater in Situ; Collection and Interpretation of Design Data 1: Site Characterization for PRBs; Reactive Materials: Zero-Valent Iron; Collection and Interpretation of Design Data 2: Laboratory and Pilot Scale Tests; Design Calculations; Compliance Monitoring, Performance Monitoring and Long-Term Maintenance for PRBs; PRB Emplacement Techniques; PRB Permitting and Implementation; Treatment of Metals; Non-Metallic Reactive Materials; Economic Considerations for PRB Deployment; and Bibliography.

  8. Naturalistic Decision Making For Power System Operators

    SciTech Connect (OSTI)

    Greitzer, Frank L.; Podmore, Robin; Robinson, Marck; Ey, Pamela

    2009-06-23T23:59:59.000Z

    Abstract: Motivation -- As indicated by the Blackout of 2003, the North American interconnected electric system is vulnerable to cascading outages and widespread blackouts. Investigations of large scale outages often attribute the causes to the three T’s: Trees, Training and Tools. A systematic approach has been developed to document and understand the mental processes that an expert power system operator uses when making critical decisions. The approach has been developed and refined as part of a capability demonstration of a high-fidelity real-time power system simulator under normal and emergency conditions. To examine naturalistic decision making (NDM) processes, transcripts of operator-to-operator conversations are analyzed to reveal and assess NDM-based performance criteria. Findings/Design -- The results of the study indicate that we can map the Situation Awareness Level of the operators at each point in the scenario. We can also identify clearly what mental models and mental simulations are being performed at different points in the scenario. As a result of this research we expect that we can identify improved training methods and improved analytical and visualization tools for power system operators. Originality/Value -- The research applies for the first time, the concepts of Recognition Primed Decision Making, Situation Awareness Levels and Cognitive Task Analysis to training of electric power system operators. Take away message -- The NDM approach provides an ideal framework for systematic training management and mitigation to accelerate learning in team-based training scenarios with high-fidelity power grid simulators.

  9. Eoeective Recognizability and Model Checking of Reactive Fioeo Automata

    E-Print Network [OSTI]

    Sutre, Grégoire

    Electre. For this, we deøne a particular behavioral model for Electre programs, Reactive Fioeo Au­ tomata speciøed with the reactive language Electre [CR95]. A reactive pro­ gram is supposed to reactEoeective Recognizability and Model Checking of Reactive Fioeo Automata G. Sutre 1 , A. Finkel 1

  10. Structural characterization of the gallosilicate TsG-1, K{sub 10}Ga{sub 10}Si{sub 22}O{sub 64}{center_dot}5H{sub 2}O, with the CGS framework topology

    SciTech Connect (OSTI)

    Lee, Y.; Kim, S.J.; Parise, J.B. [State Univ. of New York, Stony Brook, NY (United States)] [State Univ. of New York, Stony Brook, NY (United States); Kim, S.J. [Brookhaven National Lab., Upton, NY (United States). National Synchrotron Light Source] [Brookhaven National Lab., Upton, NY (United States). National Synchrotron Light Source

    1999-04-01T23:59:59.000Z

    A novel gallosilicate framework was reported by Krutskaya et al. while studying the phase diagrams of the K{sub 2}O-Ga{sub 2}O{sub 3}-SiO{sub 2}-H{sub 2}O system at 200 C. This material apparently had no aluminosilicate analogue and was named TsG-1. Although the cell parameters and the water sorption properties of this material were described, the structure of TsG-1 was not reported. The authors report here the structure of microporous TsG-1.

  11. Reactive power interconnection requirements for PV and wind plants : recommendations to NERC.

    SciTech Connect (OSTI)

    McDowell, Jason (General Electric, Schenectady, NY); Walling, Reigh (General Electric, Schenectady, NY); Peter, William (SunPower, Richmond, CA); Von Engeln, Edi (NV Energy, Reno, NV); Seymour, Eric (AEI, Fort Collins, CO); Nelson, Robert (Siemens Wind Turbines, Orlando, FL); Casey, Leo (Satcon, Boston, MA); Ellis, Abraham; Barker, Chris. (SunPower, Richmond, CA)

    2012-02-01T23:59:59.000Z

    Voltage on the North American bulk system is normally regulated by synchronous generators, which typically are provided with voltage schedules by transmission system operators. In the past, variable generation plants were considered very small relative to conventional generating units, and were characteristically either induction generator (wind) or line-commutated inverters (photovoltaic) that have no inherent voltage regulation capability. However, the growing level of penetration of non-traditional renewable generation - especially wind and solar - has led to the need for renewable generation to contribute more significantly to power system voltage control and reactive power capacity. Modern wind-turbine generators, and increasingly PV inverters as well, have considerable dynamic reactive power capability, which can be further enhanced with other reactive support equipment at the plant level to meet interconnection requirements. This report contains a set of recommendations to the North-America Electricity Reliability Corporation (NERC) as part of Task 1-3 (interconnection requirements) of the Integration of Variable Generation Task Force (IVGTF) work plan. The report discusses reactive capability of different generator technologies, reviews existing reactive power standards, and provides specific recommendations to improve existing interconnection standards.

  12. Method For Reactivating Solid Catalysts Used For Alklation Reactions

    DOE Patents [OSTI]

    Ginosar, Daniel M. (Idaho Falls, ID); Thompson, David N. (Idaho Falls, ID); Coates, Kyle (Shelley, ID); Zalewski, David J. (Proctorville, OH); Fox, Robert V. (Idaho Falls, ID)

    2005-05-03T23:59:59.000Z

    A method for reactivating a solid alkylation catalyst is provided which can be performed within a reactor that contains the alkylation catalyst or outside the reactor. Effective catalyst reactivation is achieved whether the catalyst is completely deactivated or partially deactivated. A fluid reactivating agent is employed to dissolve catalyst fouling agents and also to react with such agents and carry away the reaction products. The deactivated catalyst is contacted with the fluid reactivating agent under pressure and temperature conditions such that the fluid reactivating agent is dense enough to effectively dissolve the fouling agents and any reaction products of the fouling agents and the reactivating agent. Useful pressures and temperatures for reactivation include near-critical, critical, and supercritical pressures and temperatures for the reactivating agent. The fluid reactivating agent can include, for example, a branched paraffin containing at least one tertiary carbon atom, or a compound that can be isomerized to a molecule containing at least one tertiary carbon atom.

  13. Method for reactivating solid catalysts used in alkylation reactions

    DOE Patents [OSTI]

    Ginosar, Daniel M.; Thompson, David N.; Coates, Kyle; Zalewski, David J.; Fox, Robert V.

    2003-06-17T23:59:59.000Z

    A method for reactivating a solid alkylation catalyst is provided which can be performed within a reactor that contains the alkylation catalyst or outside the reactor. Effective catalyst reactivation is achieved whether the catalyst is completely deactivated or partially deactivated. A fluid reactivating agent is employed to dissolve catalyst fouling agents and also to react with such agents and carry away the reaction products. The deactivated catalyst is contacted with the fluid reactivating agent under pressure and temperature conditions such that the fluid reactivating agent is dense enough to effectively dissolve the fouling agents and any reaction products of the fouling agents and the reactivating agent. Useful pressures and temperatures for reactivation include near-critical, critical, and supercritical pressures and temperatures for the reactivating agent. The fluid reactivating agent can include, for example, a branched paraffin containing at least one tertiary carbon atom, or a compound that can be isomerized to a molecule containing at least one tertiary carbon atom.

  14. Water reactive hydrogen fuel cell power system

    DOE Patents [OSTI]

    Wallace, Andrew P; Melack, John M; Lefenfeld, Michael

    2014-01-21T23:59:59.000Z

    A water reactive hydrogen fueled power system includes devices and methods to combine reactant fuel materials and aqueous solutions to generate hydrogen. The generated hydrogen is converted in a fuel cell to provide electricity. The water reactive hydrogen fueled power system includes a fuel cell, a water feed tray, and a fuel cartridge to generate power for portable power electronics. The removable fuel cartridge is encompassed by the water feed tray and fuel cell. The water feed tray is refillable with water by a user. The water is then transferred from the water feed tray into a fuel cartridge to generate hydrogen for the fuel cell which then produces power for the user.

  15. Water reactive hydrogen fuel cell power system

    DOE Patents [OSTI]

    Wallace, Andrew P; Melack, John M; Lefenfeld, Michael

    2014-11-25T23:59:59.000Z

    A water reactive hydrogen fueled power system includes devices and methods to combine reactant fuel materials and aqueous solutions to generate hydrogen. The generated hydrogen is converted in a fuel cell to provide electricity. The water reactive hydrogen fueled power system includes a fuel cell, a water feed tray, and a fuel cartridge to generate power for portable power electronics. The removable fuel cartridge is encompassed by the water feed tray and fuel cell. The water feed tray is refillable with water by a user. The water is then transferred from the water feed tray into the fuel cartridge to generate hydrogen for the fuel cell which then produces power for the user.

  16. STOMP-ECKEChem: An Engineering Perspective on Reactive Transport in Geologic Media

    SciTech Connect (OSTI)

    White, Mark D.; Fang, Yilin

    2012-04-04T23:59:59.000Z

    ECKEChem (Equilibrium, Conservation, Kinetic Equation Chemistry) is a reactive transport module for the STOMP suite of multifluid subsurface flow and transport simulators that was developed from an engineering perspective. STOMP comprises a suite of operational modes that are distinguished by the solved coupled conservation equations with capabilities for a variety of subsurface applications (e.g., environmental remediation and stewardship, geologic sequestration of greenhouse gases, gas hydrate production, and oil shale production). The ECKEChem module was designed to provide integrated reactive transport capabilities across the suite of STOMP simulator operational modes. The initial application for the ECKEChem module was in the simulation of the mineralization reactions that occurred with the injection of supercritical carbon dioxide into deep Columbia River basalt formations, where it was implemented in the STOMP-CO2 simulator. The STOMP-ECKEChem solution approach to modeling reactive transport in multifluid geologic media is founded on an engineering perspective: (1) sequential non-iterative coupling between the flow and reactive transport is sufficient, (2) reactive transport can be modeled by operator splitting with local geochemistry and global transport, (3) geochemistry can be expressed as a system of coupled nonlinear equilibrium, conservation and kinetic equations, (4) a limited number of kinetic equation forms are used in geochemical practice. This chapter describes the conceptual approach to converting a geochemical reaction network into a series of equilibrium, conservation and kinetic equations, the implementation of ECKEChem in STOMP, the numerical solution approach, and a demonstration of the simulator on a complex application involving desorption of uranium from contaminated field-textured sediments.

  17. Studies on Waterborne Pathogen Reactivation after Disinfection

    E-Print Network [OSTI]

    Kaur, Jasjeet

    2013-12-09T23:59:59.000Z

    ultraviolet (LP UV) irradiation at five titanium dioxide (TiO_(2)) concentrations (1 g/L, 0.5 g/L, 0.75 g/L, and 0.1 g/L) to achieve 5 log_(10) reduction of a laboratory E. coli K-12 strain (ATCC® 10798). Regrowth and reactivation of E. coli in dark and light...

  18. Controlling uranium reactivity March 18, 2008

    E-Print Network [OSTI]

    Meyer, Karsten

    for the last decade. Most of their work involves depleted uranium, a more common form of uraniumMarch 2008 Controlling uranium reactivity March 18, 2008 Uranium is an often misunderstood metal uranium research. In reality, uranium presents a wealth of possibilities for funda- mental chemistry. Many

  19. REAC/TS

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:AdministrationAnalysis andBHoneywell9/%2A en International

  20. Assessment of the Economic Potential of Microgrids for Reactive Power Supply

    E-Print Network [OSTI]

    Appen, Jan von

    2012-01-01T23:59:59.000Z

    Reactive Power from Distributed Energy”, The Electricityvoltage. Electricity consumers’ demand for reactive power ison electricity supply security, the costs of local reactive

  1. Operating Costs

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1997-03-28T23:59:59.000Z

    This chapter is focused on capital costs for conventional construction and environmental restoration and waste management projects and examines operating cost estimates to verify that all elements of the project have been considered and properly estimated.

  2. Simultaneous MS-IR Studies of Surface Formate Reactivity Under...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MS-IR Studies of Surface Formate Reactivity Under Methanol Synthesis Conditions on CuSiO2. Simultaneous MS-IR Studies of Surface Formate Reactivity Under Methanol Synthesis...

  3. Isotope effects in methanol synthesis and the reactivity of copper...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Isotope effects in methanol synthesis and the reactivity of copper formates on a CuSiO2 catalyst. Isotope effects in methanol synthesis and the reactivity of copper formates on a...

  4. Parallel Web Scripting with Reactive Constraints Thibaud Hottelier

    E-Print Network [OSTI]

    Bodik, Rastisla

    Parallel Web Scripting with Reactive Constraints Thibaud Hottelier James Ide Doug Kimelman Ras Bodik Electrical Engineering and Computer Sciences University of California at Berkeley Technical Report to lists, requires prior specific permission. #12;Parallel Web Scripting with Reactive Constraints Thibaud

  5. The effects of radient heat on pain reactivity 

    E-Print Network [OSTI]

    Kallina, Charles Frank

    1994-01-01T23:59:59.000Z

    Prior research has shown that an aversive event can produce either a decrease (hypoalgesia) or an increase in pain reactivity (hyperalgesia). The present study explores the impact of a suprathreshold exposure to radiant heat on pain reactivity. Rats...

  6. Reactive Dehydration technology for Production of Fuels and Chemicals...

    Broader source: Energy.gov (indexed) [DOE]

    platform (Intensified Catalytic and Reactive Distillation) for compact, inexpensive production of biomass-based chemicals from complex aqueous mixtures. Separation...

  7. Chemically Reactive Working Fluids for the Capture and Transport...

    Broader source: Energy.gov (indexed) [DOE]

    More Documents & Publications Planar Optical Waveguide Coupler Transformers for High-Power Solar Enegy Collection and Transmission Chemically Reactive Working...

  8. Constraining |V(td)|/|V(ts)| Using Radiative Penguin B -> V(K*/rho/omega)gamma Decays

    SciTech Connect (OSTI)

    Tan, Ping; /Wisconsin U., Madison

    2006-03-08T23:59:59.000Z

    Exclusive radiative penguin B decays, B {yields} (K*{sup 0}/K*{sup +}) and B {yields} ({rho}/{omega}){gamma}, are flavor-changing neutral-current (FCNC) processes. Studies of these decays are of special interest in testing Standard Model (SM) predictions and searching for other beyond-the-SM FCNC interactions. Using 89 x 10{sup 6} B{bar B} pairs from BABAR, we measure the branching fraction ({Beta}), CP-asymmetry ({Alpha}), and isospin asymmetry ({Delta}{sub 0-}) of B {yields} (K*{sup 0}/K*{sup +}){gamma} as follows: {Beta}(B{sup 0} {yields} K*{sup 0}{gamma}) = 3.92 {+-} 0.20(stat.) {+-} 0.24(syst.); {Beta}(B{sup +} {yields} K*{sup +}{gamma}) = 3.87 {+-} 0.28(stat.) {+-} 0.26(syst.); {Alpha}(B {yields} K*{gamma}) = -0.013 {+-} 0.36(stat.) {+-} 0.10(syst.); {Delta}{sub 0-}(B {yields} K*{gamma}) = 0.050 {+-} 0.045(stat.) {+-} 0.028(syst.) {+-} 0.024(R{sup +/0}). The 90% confidence intervals for the CP-asymmetry and the isospin-asymmetry in the B {yields} K*{gamma} decay are given as: -0.074 < {Alpha}(B {yields} K*{gamma}) < 0.049, -0.046 < {Delta}{sub 0-} (B {yields} K*{gamma}) < 0.146. We also search for B {yields} ({rho}/{omega}){gamma} decays using 211 x 10{sup 6} B{bar B} pairs from BABAR. No evidence for these decays is found. We set the upper limits at 90% confidence level for these decays: {Beta}(B{sup 0} {yields} {rho}{sup 0}{gamma}) < 0.4 x 10{sup -6}; {Beta}(B{sup +}{yields} {rho}{sup =}{gamma}) < 1.8 x 10{sup -6}; {Beta}(B{sup 0} {yields} {omega}{gamma}) < 1.0 x 10{sup -6}; {bar {Beta}}(B {yields} ({rho}/{omega}){gamma}) < 1.2 x 10{sup -6}. These results are in good agreement with the SM predictions. The branching fractions of these decays are then used to constrain the ratio |V{sub td}|/|V{sub ts}|.

  9. The Simulation of Synchronous Reactive Systems In Ptolemy II

    E-Print Network [OSTI]

    The Simulation of Synchronous Reactive Systems In Ptolemy II by Paul Whitaker Submitted to the Department of Electrical Engineering and Computer Sciences, University of California at Berkeley, in partial;_____________________________________________________________________ Simulation of Synchronous Reactive Systems in Ptolemy II ii Abstract The Synchronous Reactive (SR) domain

  10. Autonomic Reactive Systems via Online Learning Sanjit A. Seshia

    E-Print Network [OSTI]

    California at Irvine, University of

    Autonomic Reactive Systems via Online Learning Sanjit A. Seshia Department of Electrical@eecs.berkeley.edu Abstract-- Reactive systems are those that maintain an ongoing interaction with their environment- covering a class of reactive systems from run-time failures. This class of systems comprises those whose

  11. Towards Synthesis of Reactive & Robust Behavior Chains Amol D. Mali

    E-Print Network [OSTI]

    Mali, Amol D.

    Towards Synthesis of Reactive & Robust Behavior Chains Amol D. Mali Electrical Engg. & Computer robots need to be reactive and robust. Behavior-based robots that identify and repair the failures have of reactivity and robustness have been hitherto only informally used and have been loaded with var- ious

  12. A Synchronous Approach to Reactive System Design1 Charles Andr

    E-Print Network [OSTI]

    André, Charles

    our experience teaching discrete-event reactive systems to Electrical Engineering students. The courseA Synchronous Approach to Reactive System Design1 Charles André I3S Laboratory ­ UNSA/CNRS BP 121 This paper was presented at the 12th EAEEIE Annual Conf., 14-16 May 2001, Nancy (France). Abstract Reactive

  13. On Some Properties of Instantaneous Active and Reactive Powers

    E-Print Network [OSTI]

    Czarnecki, Leszek S.

    On Some Properties of Instantaneous Active and Reactive Powers Leszek S. CZARNECKI, Fellow IEEE Louisiana State University, USA Abstract: Some features of the instantaneous active and reactive powers p control. Also it was shown that the instantaneous reactive power q cannot be interpreted as a measure

  14. ENVIRONMENTAL REACTIVITY OF SOLID STATE HYDRIDE MATERIALS

    SciTech Connect (OSTI)

    Gray, J; Donald Anton, D

    2009-04-23T23:59:59.000Z

    In searching for high gravimetric and volumetric density hydrogen storage systems, it is inevitable that higher energy density materials will be used. In order to make safe and commercially acceptable condensed phase hydrogen storage systems, it is important to understand quantitatively the risks involved in using and handling these materials and to develop appropriate mitigation strategies to handle potential material exposure events. A crucial aspect of the development of risk identification and mitigation strategies is the development of rigorous environmental reactivity testing standards and procedures. This will allow for the identification of potential risks and implementation of risk mitigation strategies. Modified testing procedures for shipping air and/or water sensitive materials, as codified by the United Nations, have been used to evaluate two potential hydrogen storage materials, 2LiBH{sub 4} {center_dot} MgH{sub 2} and NH{sub 3}BH{sub 3}. The modified U.N. procedures include identification of self-reactive substances, pyrophoric substances, and gas-emitting substances with water contact. The results of these tests for air and water contact sensitivity will be compared to the pure material components where appropriate (e.g. LiBH{sub 4} and MgH{sub 2}). The water contact tests are divided into two scenarios dependent on the hydride to water mole ratio and heat transport characteristics. Air contact tests were run to determine whether a substance will spontaneously react with air in a packed or dispersed form. In the case of the 2LiBH{sub 4} {center_dot} MgH{sub 2} material, the results from the hydride mixture compared to the pure materials results showed the MgH{sub 2} to be the least reactive component and LiBH{sub 4} the more reactive. The combined 2LiBH{sub 4} {center_dot} MgH{sub 2} resulted in a material having environmental reactivity between these two materials. Relative to 2LiBH{sub 4} {center_dot} MgH{sub 2}, the chemical hydride NH{sub 3}BH{sub 3} was observed to be less environmentally reactive.

  15. Reactivity control assembly for nuclear reactor. [LMFBR

    DOE Patents [OSTI]

    Bollinger, L.R.

    1982-03-17T23:59:59.000Z

    This invention, which resulted from a contact with the United States Department of Energy, relates to a control mechanism for a nuclear reactor and, more particularly, to an assembly for selectively shifting different numbers of reactivity modifying rods into and out of the core of a nuclear reactor. It has been proposed heretofore to control the reactivity of a breeder reactor by varying the depth of insertion of control rods (e.g., rods containing a fertile material such as ThO/sub 2/) in the core of the reactor, thereby varying the amount of neutron-thermalizing coolant and the amount of neutron-capturing material in the core. This invention relates to a mechanism which can advantageously be used in this type of reactor control system.

  16. Nuclear reactivity control using laser induced polarization

    DOE Patents [OSTI]

    Bowman, Charles D. (Los Alamos, NM)

    1990-01-01T23:59:59.000Z

    A control element for reactivity control of a fission source provides an atomic density of .sup.3 He in a control volume which is effective to control criticality as the .sup.3 He is spin-polarized. Spin-polarization of the .sup.3 He affects the cross section of the control volume for fission neturons and hence, the reactivity. An irradiation source is directed within the .sup.3 He for spin-polarizing the .sup.3 He. An alkali-metal vapor may be included with the .sup.3 He where a laser spin-polarizes the alkali-metal atoms which in turn, spin-couple with .sup.3 He to spin-polarize the .sup.3 He atoms.

  17. Nuclear reactivity control using laser induced polarization

    DOE Patents [OSTI]

    Bowman, Charles D. (Los Alamos, NM)

    1991-01-01T23:59:59.000Z

    A control element for reactivity control of a fission source provides an atomic density of .sup.3 He in a control volume which is effective to control criticality as the .sup.3 He is spin-polarized. Spin-polarization of the .sup.3 He affects the cross section of the control volume for fission neutrons and hence, the reactivity. An irradiation source is directed within the .sup.3 He for spin-polarizing the .sup.3 He. An alkali-metal vapor may be included with the .sup.3 He where a laser spin-polarizes the alkali-metal atoms which in turn, spin-couple with .sup.3 He to spin-polarize the .sup.3 He atoms.

  18. Reactive Attachment Disorder: Concepts, Treatment, and Research

    E-Print Network [OSTI]

    Walter, Uta M.; Petr, Chris

    2004-06-01T23:59:59.000Z

    Best Practices in Children’s Mental Health: A Series of Reports Summarizing the Empirical Research on Selected Topics Report #11 “Reactive Attachment Disorder: Concepts, Treatment and Research” June, 2004... Healthcare” Report #8 – October 2003, “Best Practices in Therapeutic Foster Care: Review of the Literature and Local Practices in the State of Kansas” Report #9 – December 2003, “Juveniles with Sexual Offending Behaviors” Report #10-February 2004...

  19. Operations Videos

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)IntegratedSpeeding access toTest and EvaluationOperational ManagementCenterOperations

  20. The determination of neutron flux in the Texas A & M triga reactor during pulse and steady-state operations

    E-Print Network [OSTI]

    O'Donnell, John Joseph

    1983-01-01T23:59:59.000Z

    . Core VIIi Diagram mith 90 FLIP clemente The NSC reactor technical specification and license approved by the United States Nuclear Regulatory Commission (NRC) limits reactor operations so that a temperature of 830 Celsius is not reached anywhere... is significantly more than that allowed for operation with Core VIII. However, a small reactivity insertion in Core VIII will produce approximately the same peak power in a pulse as the much larger reactivity insertion produced during pulse operation of Core...

  1. A novel reactive processing technique: using telechelic polymers to reactively compatibilize polymer blends

    SciTech Connect (OSTI)

    Ashcraft, Earl C [ORNL; Ji, Haining [ORNL; Mays, Jimmy [ORNL; Dadmun, Mark D [ORNL

    2009-01-01T23:59:59.000Z

    Difunctional reactive polymers, telechelics, were used to reactively form multiblock copolymers in situ when melt-blended with a blend of polystyrene and polyisoprene. To quantify the ability of the copolymer to compatibilize the blends, the time evolution of the domain size upon annealing was analyzed by SEM. It was found that the most effective parameter to quantify the ability of the copolymer to inhibit droplet coalescence is Kreltstable, the relative coarsening constant multiplied by the stabilization time. These results indicate that intermediate-molecular-weight telechelic pairs of both highly reactive Anhydride-PS-Anhydride/NH2-PI-NH2 and slower reacting Epoxy-PS-Epoxy/COOH-PI-COOH both effectively suppress coalescence, with the optimal molecular weight being slightly above the critical molecular weight of the homopolymer,Mc. The effects of telechelic loading were also investigated, where the optimal loading concentration for this system was 0.5 wt %, as higher concentrations exhibited a plasticizing effect due to the presence of unreacted low-molecular-weight telechelics present in the blend. A determination of the interfacial coverage of the copolymer shows that a conversion of 1.5-3.0% was required for 20% surface coverage at 5.0 wt % telechelic loading, indicating a large excess of telechelics in this system. At the optimal loading level of 0.5 wt %, a conversion of 15% was required for 20% surface coverage. The results of these experiments provide a clear understanding of the role of telechelic loading and molecular weight on its ability to reactively form interfacial modifiers in phase-separated polymer blends and provide guidelines for the development of similar reactive processing schemes that can use telechelic polymers to reactively compatibilize a broad range of polymer blends.

  2. Operation Poorman

    SciTech Connect (OSTI)

    Pruvost, N.; Tsitouras, J.

    1981-03-18T23:59:59.000Z

    The objectives of Operation Poorman were to design and build a portable seismic system and to set up and use this system in a cold-weather environment. The equipment design uses current technology to achieve a low-power, lightweight system that is configured into three modules. The system was deployed in Alaska during wintertime, and the results provide a basis for specifying a mission-ready seismic verification system.

  3. Operating Strategies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for RenewableSpeeding accessSpeedingOctoberResearchOpen→ globalOPERATING PLAN

  4. Operations Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for RenewableSpeeding accessSpeedingOctoberResearchOpen→ globalOPERATING

  5. A decomposition approach to optimal reactive power dispatch in large-scale power systems

    SciTech Connect (OSTI)

    Deeb, N.I.

    1989-01-01T23:59:59.000Z

    Power systems network operation is aimed at reducing system losses and minimizing the operational cost while satisfying performance requirements in normal and contingency situations. In this project, the procedure for the reactive power optimization has the solutions for investment and operation subproblems. The global solution is an iterative process between these two subproblems using the Bender decomposition method. In the investment subproblem decisions for the capacity and location of new reactive sources are made. These decisions are used in the optimization of the system operation. The outstanding features of the proposed method are that it does not require any matrix inversion, will save computation time and memory space, and can be implemented on very large scale power systems. The method employs a linearized objective function and constraints, and is based on adjusting control variables which are tap positions of transformers and reactive power injections. Linear programming is used to calculate voltage increments, which would minimize transmission losses, and adjustments of control variables would be obtained by a modified Jacobian matrix. This approach would greatly simplify the application of Dantzig-Wolfe decomposition method for solving the operation subproblem. According to the mathematical features of the Dantzig-Wolfe method, a multi-area approach is implemented and system equations are decomposed into a master problem and several subproblems. The master problem is formed by constraints, which represent linking transmission lines between areas. Two updated techniques are incorporated in the method to enhance the optimization process, which would save additional computation time and memory space. The proposed method is applied to the IEEE-30 bus system, a 60-bus system, a 180-bus system and a 1200-bus system, and numerical results are presented.

  6. Relative reactivities of solid benzoic acids

    E-Print Network [OSTI]

    Warwas, Edwin James

    1967-01-01T23:59:59.000Z

    REACTIVITIES OF SOLID BENZOIC ACIDS (January 1967) Edwin James Warwas B. S. , Southwest Texas State College Directed by: Dr. C. K. Hancock and Dr. E. A. Meyers The reactions of solid benzoic acid (BZAH) and nine m- or p- substituted benzoic acids (RBZAH...) with solid potassium benzoate (BZAK) and m- or p-substituted potassium benzoates (R'BZAK) have been carried out in sealed thin-walled glass capillary tubes or in 0 sealed weighing bottles at 70 For the reaction, RBZAH + R'BZAK, where R = R', the product...

  7. Preparation of reactive beta-dicalcium silicate

    DOE Patents [OSTI]

    Shen, Ming-Shing (Laramie, WY, NJ); Chen, James M. (Rahway, NJ); Yang, Ralph T. (Amherst, NY)

    1982-01-01T23:59:59.000Z

    This invention relates to the preparation of fine particles of reactive beta-dicalcium silicate by means of a solid state process which comprises firing a mixture of calcium sulfate, silica and a reducing additive selected from the group consisting of calcium sulfide, carbon, carbon monoxide, methane and hydrogen, at a temperature of about 850.degree.-1000.degree. C. A carrier gas such as nitrogen or carbon dioxide may also be added, if desired. A high concentration of sulfur dioxide is a by-product of this process.

  8. Preparation of reactive beta-dicalcium silicate

    DOE Patents [OSTI]

    Shen, M.S.; Chen, J.M.; Yang, R.T.

    1980-02-28T23:59:59.000Z

    This invention relates to the preparation of fine particles of reactive beta-dicalcium silicate by means of a solid state process which comprises firing a mixture of calcium sulfate, silica, and a reducing additive selected from the group consisting of calcium sulfide, carbon, carbon monoxide, methane, and hydrogen, at a temperature of about 850 to 1000/sup 0/C. A carrier gas such as nitrogen or carbon dioxide may also be added, if desired. A high concentration of sulfur dioxide is a by-product of this process.

  9. Reactive sticking coefficients of silane on silicon

    SciTech Connect (OSTI)

    Buss, R.J.; Ho, P.; Breiland, W.G.; Coltrin, M.E.

    1988-09-15T23:59:59.000Z

    Reactive sticking coefficients (RSCs) were measured for silane and disilane on polycrystalline silicon for a wide range of temperature and flux (pressure) conditions. The data were obtained from deposition rate measurements using molecular beam scattering and a very low pressure cold wall reactor. The RSCs have non-Arrhenius temperature dependences and decreases with increasing flux at low (710/sup 0/) temperatures. A simple model involving dissociative adsorption of silane is consistent with these results. The results are compared with previous studies of the SiH/sub 4//Si(s) reaction.

  10. Operational Excellence

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > TheNuclear Astrophysics One ofSpeedingthis site » OpenOperational

  11. Operations Information

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for RenewableSpeeding accessSpeedingOctoberResearchOpen→ globalOPERATING Who We

  12. Examination of a PHEV Bi-Directional Charger System for V2G Reactive Power Compensation

    SciTech Connect (OSTI)

    Kisacikoglu, Mithat C [ORNL] [ORNL; Ozpineci, Burak [ORNL] [ORNL; Tolbert, Leon M [ORNL] [ORNL

    2010-01-01T23:59:59.000Z

    Plug-in hybrid electric vehicles (PHEVs) potentially have the capability to fulfill the energy storage needs of the electric grid by supplying ancillary services such as reactive power compensation. However, in order to allow bidirectional power transfer, the PHEV battery charger should be designed to manage such capability. While many different battery chargers have been available since the inception of the first electric vehicles (EVs), an on-board, conductive charger with bidirectional power transferring capability have recently drawn attention due to their inherent advantages in charging accessibility, ease of use and efficiency. In this study, a reactive power compensation case study using the inverter dc-link capacitor is given when a PHEV battery is under charging operation. Finally, the impact of providing these services on the batteries is also explained.

  13. Analyzing the status of oxide surface photochemical reactivity...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    photochemical reactivity Released: July 28, 2013 Invited review shows power of scanning tunneling microscopy to understand and control the surface photochemistry of oxide...

  14. advanced reactivity measurement: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Alfredo) 2011-01-01 302 High Purity Ethyl Acetate Production with a Batch Reactive Distillation Column using Dynamic Optimization Strategy CiteSeer Summary: AbstractEthyl...

  15. advanced reactivity measurement facility-1: Topics by E-print...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Alfredo) 2011-01-01 306 High Purity Ethyl Acetate Production with a Batch Reactive Distillation Column using Dynamic Optimization Strategy CiteSeer Summary: AbstractEthyl...

  16. Airborne measurement of OH reactivity during INTEX-B

    E-Print Network [OSTI]

    2009-01-01T23:59:59.000Z

    plus OH sign), reactiv- propane ing different gases gases atisoprene (plus sign), propane (star) and propene (triangle).NMHC includes ethane, ethene, propane, propene, i-butane, n-

  17. Optimization Online - Reactive Power Management using Firefly and ...

    E-Print Network [OSTI]

    Ripunjoy Phukan

    2013-10-04T23:59:59.000Z

    Oct 4, 2013 ... Reactive Power Management using Firefly and Spiral Optimization under Static and Dynamic Loading Conditions. Ripunjoy Phukan (ripun000 ...

  18. Advancing Reactive Tracer Methods for Measuring Thermal Evolution...

    Open Energy Info (EERE)

    Advancing Reactive Tracer Methods for Measuring Thermal Evolution in CO2- and Water-Based Geothermal Reservoirs Geothermal Lab Call Project Jump to: navigation, search Last...

  19. Quantitative Site-specific Reactivity Profiling of S-Nitrosylation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Profiling of S-Nitrosylation in Mouse Skeletal Muscle Using Cysteinyl Peptide Enrichment Quantitative Site-specific Reactivity Profiling of S-Nitrosylation in Mouse Skeletal...

  20. Ground rubber: Reactive permeable barrier sorption media

    SciTech Connect (OSTI)

    Kershaw, D.S.; Pamukcu, S. [Lehigh Univ., Bethlehem, PA (United States)

    1997-12-31T23:59:59.000Z

    The objective of this research was to examine the feasibility of using ground tire rubber as a sorbent media in reactive permeable barrier systems. Previous research by the current authors has demonstrated that tire rubber can sorb significant quantities of benzene, toluene, ethylbenzene and O-xylene from aqueous solutions. The current research was run to examine the usage rate of ground rubber in a packed bed reactor under specific contact times. In addition, desorption and repetitive sorption tests were run to determine the reversibility of the sorption process for ground tire rubber. These tests were run to determine the regeneration capacity of ground tire rubber. Results of the study show that the usage rates are greater than 50% with an empty bed contact times of 37 minutes, and minimal amounts of energy are needed to regenerate the tire rubber after use.

  1. Completing the complex Poynting theorem: Conservation of reactive energy in reactive time

    E-Print Network [OSTI]

    Gerald Kaiser

    2014-12-11T23:59:59.000Z

    The complex Poynting theorem is extended canonically to a time-scale domain $(t, s)$ by replacing the phasors of time-harmonic fields by the analytic signals $X(r, t+is)$ of fields $X(r,t)$ with general time dependence. The imaginary time $s>0$ is shown to play the role of a time resolution scale, and the extended Poynting theorem splits into two conservation laws: its real part gives the conservation in $t$ of the scale-averaged active energy at fixed $s$, and its imaginary part gives the conservation in $s$ of the scale-averaged reactive energy at fixed $t$. At coarse scales (large $s$, slow time), where the system reduces to the circuit level, this may have applications to the theory of electric power transmission and conditioning. At fine scales (small $s$, fast time) it describes reactive energy dynamics in radiating systems.

  2. Simultaneous Efficiency, NOx, and Smoke Improvements through Diesel/Gasoline Dual-Fuel Operation in a Diesel Engine 

    E-Print Network [OSTI]

    Sun, Jiafeng

    2014-08-05T23:59:59.000Z

    Diesel/gasoline dual-fuel combustion uses both gasoline and diesel fuel in diesel engines to exploit their different reactivities. This operation combines the advantages of diesel fuel and gasoline while avoiding their disadvantages, attains...

  3. ALUMINOSILICATE-COATED SILICA SAND FOR REACTIVE TRANSPORT EXPERIMENTS

    E-Print Network [OSTI]

    Flury, Markus

    ALUMINOSILICATE-COATED SILICA SAND FOR REACTIVE TRANSPORT EXPERIMENTS By JORGE ANTONIO JEREZ transport experiments; Dr. Barbara Williams and Jason Shira from University of Idaho for providing access-COATED SILICA SAND FOR REACTIVE TRANSPORT EXPERIMENTS Abstract by Jorge Antonio Jerez Briones, Ph.D. Washington

  4. Assessment of sequence homology and cross-reactivity

    SciTech Connect (OSTI)

    Aalberse, Rob C. [Department of Immunopathology, Sanquin Research at CLB, Plesmanlaan 125, 1066 CX Amsterdam (Netherlands) and Landsteiner Laboratory, Academic Medical Centre, 1066 CX Amsterdam (Netherlands)]. E-mail: r.aalberse@sanquin.nl

    2005-09-01T23:59:59.000Z

    Three aspects of allergenicity assessment and are discussed: IgE immunogenicity, IgE cross-reactivity and T cell cross-reactivity, all with emphasis on in-silico predictability: from amino acid sequence via 3D structure to allergenicity.(1)IgE immunogenicity depends to an overwhelming degree on factors other than the protein itself: the context and history of the protein by the time it reaches the immune system. Without specification of these two factors very few foreign proteins can be claimed to be absolutely non-allergenic. Any antigen may be allergenic, particularly if it avoids activation of TH2-suppressive mechanisms (CD8 cells, TH1 cells, other regulatory T cells and regulatory cytokines). (2)IgE cross-reactivity can be much more reliably assessed by a combination of in-silico homology searches and in vitro IgE antibody assays. The in-silico homology search is unlikely to miss potential cross-reactivity with sequenced allergens. So far, no biologically relevant cross-reactivity at the antibody level has been demonstrated between proteins without easily-demonstrable homology. (3)T cell cross-reactivity is much more difficult to predict compared to B cell cross-reactivity, and its effects are more diverse. Yet, pre-existing cross-reactive T cell activity is likely to influence the outcome not only of the immune response, but also of the effector phase of the allergic reaction.

  5. SHUSH: Reactive Transmit Power Control For Wireless MAC Protocols

    E-Print Network [OSTI]

    Han, Richard Y.

    SHUSH: Reactive Transmit Power Control For Wireless MAC Protocols Anmol Sheth and Richard Han@cs.colorado.edu Abstract-- Asymmetric transmission ranges caused due to transmit power control have the undesirable effect access. In this paper we present a new reactive power controlled MAC protocol, SHUSH, which tackles

  6. Multispecies Reactive Tracer Test in a Sand and

    E-Print Network [OSTI]

    Multispecies Reactive Tracer Test in a Sand and Gravel Aquifer, Cape Cod, Massachusetts United;Multispecies Reactive Tracer Test in a Sand and Gravel Aquifer, Cape Cod, Massachusetts Part 2 Transport- effectiveness for prevention and control of pollution to air, land, water, and subsurface resources; protection

  7. The Specification and Execution of Heterogeneous Synchronous Reactive Systems

    E-Print Network [OSTI]

    The Specification and Execution of Heterogeneous Synchronous Reactive Systems by Stephen Anthony in Engineering---Electrical Engineering and Computer Sciences in the GRADUATE DIVISION of the UNIVERSITY of Heterogeneous Synchronous Reactive Systems Copyright ã 1997 by Stephen Anthony Edwards #12; Abstract

  8. A Modified Reactive Control Framework for Cooperative Mobile Robots

    E-Print Network [OSTI]

    A Modified Reactive Control Framework for Cooperative Mobile Robots J. Salido a , J.M. Dolan a , J Dept. of Electrical & Computer Engineering, Carnegie Mellon Univ. Pittsburgh, PA 15213­3890 USA. Purely reactive approaches such as that of Brooks are efficient, but lack a mechanism for global control

  9. Reactive Sputtering of Bismuth Vanadate Photoanodes for Solar Water Splitting

    E-Print Network [OSTI]

    Javey, Ali

    Reactive Sputtering of Bismuth Vanadate Photoanodes for Solar Water Splitting Le Chen,, Esther of Electrical Engineering and Computer Sciences, University of California, Berkeley, Berkeley, California 94720 has remained relatively underexplored. Here, we report the synthesis of BiVO4 thin films by reactive

  10. Reactive Rearrangement of Parts under Sensor Inaccuracy: Particle Filter Approach

    E-Print Network [OSTI]

    Reactive Rearrangement of Parts under Sensor Inaccuracy: Particle Filter Approach Hal^uk Bayram, Electrical and Electronic Engineering Bogazici University, Bebek 34342 Istanbul Turkey Abstract-- The paper will be left undisturbed, the robot is required to employ a reactive strategy. A feedback-based event

  11. Reactive oxygen species deglycosilate glomerular a-dystroglycan

    E-Print Network [OSTI]

    Campbell, Kevin P.

    Reactive oxygen species deglycosilate glomerular a-dystroglycan NPJ Vogtla¨nder1 , WPM Tamboer1 open. Reactive oxygen species (ROS) are known to degrade and depolymerize carbohydrates, and to playDa in skeletal muscle, ranging from 120 kDa in brain to 190 kDa in the Torpedo electric organ.8

  12. Towards Interactive Timing Analysis for Designing Reactive Systems

    E-Print Network [OSTI]

    Towards Interactive Timing Analysis for Designing Reactive Systems Insa Fuhrmann David Broman Steven Smyth Reinhard von Hanxleden Electrical Engineering and Computer Sciences University of California Interactive Timing Analysis for Designing Reactive Systems Insa Fuhrmann1 , David Broman2,3 , Steven Smyth1

  13. Reactive ion etched substrates and methods of making and using

    DOE Patents [OSTI]

    Rucker, Victor C. (San Francisco, CA); Shediac, Rene (Oakland, CA); Simmons, Blake A. (San Francisco, CA); Havenstrite, Karen L. (New York, NY)

    2007-08-07T23:59:59.000Z

    Disclosed herein are substrates comprising reactive ion etched surfaces and specific binding agents immobilized thereon. The substrates may be used in methods and devices for assaying or isolating analytes in a sample. Also disclosed are methods of making the reactive ion etched surfaces.

  14. A REACTIVE APPROACH FOR MINING PROJECT EVALUATION UNDER PRICE UNCERTAINTY

    E-Print Network [OSTI]

    Duffy, Ken

    A REACTIVE APPROACH FOR MINING PROJECT EVALUATION UNDER PRICE UNCERTAINTY Meimei Zhang. This method often undervalues a mining project since it ignores future price uncertainty and does not allow on metal price. This paper also demonstrates that the "reactive" approach can estimate the mine project

  15. CLASSIFICATION AND REACTIVITY OF SECONDARY ALUMINUM PRODUCTION WASTE

    E-Print Network [OSTI]

    environment.14 Keywords: Landfills, aluminum, hydrogen, salt cake, dross, calorimeter, waste disposal15 16 17CLASSIFICATION AND REACTIVITY OF SECONDARY ALUMINUM PRODUCTION WASTE Navid H. Jafari Student Member and Reactivity of Secondary Aluminum Production Waste1 Navid H. Jafari1 , Timothy D. Stark2 and Ralph Roper3 2 3

  16. Biodiesel Fuel Property Effects on Particulate Matter Reactivity

    SciTech Connect (OSTI)

    Williams, A.; Black, S.; McCormick, R. L.

    2010-06-01T23:59:59.000Z

    Controlling diesel particulate emissions to meet the 2007 U.S. standard requires the use of a diesel particulate filter (DPF). The reactivity of soot, or the carbon fraction of particulate matter, in the DPF and the kinetics of soot oxidation are important in achieving better control of aftertreatment devices. Studies showed that biodiesel in the fuel can increase soot reactivity. This study therefore investigated which biodiesel fuel properties impact reactivity. Three fuel properties of interest included fuel oxygen content and functionality, fuel aromatic content, and the presence of alkali metals. To determine fuel effects on soot reactivity, the performance of a catalyzed DPF was measured with different test fuels through engine testing and thermo-gravimetric analysis. Results showed no dependence on the aromatic content or the presence of alkali metals in the fuel. The presence and form of fuel oxygen was the dominant contributor to faster DPF regeneration times and soot reactivity.

  17. Early maturation processes in coal. Part 2: Reactive dynamics simulations using the ReaxFF reactive force field on Morwell Brown coal structures

    E-Print Network [OSTI]

    Goddard III, William A.

    Early maturation processes in coal. Part 2: Reactive dynamics simulations using the ReaxFF reactive force field on Morwell Brown coal structures Elodie Salmon a , Adri C.T. van Duin b , François Lorant Brown coal using the ReaxFF reactive force field. We find that these reactive MD simulations

  18. A SCOPING STUDY: Development of Probabilistic Risk Assessment Models for Reactivity Insertion Accidents During Shutdown In U.S. Commercial Light Water Reactors

    SciTech Connect (OSTI)

    S. Khericha

    2011-06-01T23:59:59.000Z

    This report documents the scoping study of developing generic simplified fuel damage risk models for quantitative analysis from inadvertent reactivity insertion events during shutdown (SD) in light water pressurized and boiling water reactors. In the past, nuclear fuel reactivity accidents have been analyzed both mainly deterministically and probabilistically for at-power and SD operations of nuclear power plants (NPPs). Since then, many NPPs had power up-rates and longer refueling intervals, which resulted in fuel configurations that may potentially respond differently (in an undesirable way) to reactivity accidents. Also, as shown in a recent event, several inadvertent operator actions caused potential nuclear fuel reactivity insertion accident during SD operations. The set inadvertent operator actions are likely to be plant- and operation-state specific and could lead to accident sequences. This study is an outcome of the concern which arose after the inadvertent withdrawal of control rods at Dresden Unit 3 in 2008 due to operator actions in the plant inadvertently three control rods were withdrawn from the reactor without knowledge of the main control room operator. The purpose of this Standardized Plant Analysis Risk (SPAR) Model development project is to develop simplified SPAR Models that can be used by staff analysts to perform risk analyses of operating events and/or conditions occurring during SD operation. These types of accident scenarios are dominated by the operator actions, (e.g., misalignment of valves, failure to follow procedures and errors of commissions). Human error probabilities specific to this model were assessed using the methodology developed for SPAR model human error evaluations. The event trees, fault trees, basic event data and data sources for the model are provided in the report. The end state is defined as the reactor becomes critical. The scoping study includes a brief literature search/review of historical events, developments of a small set of comprehensive event trees and fault trees and recommendation for future work.

  19. Advancing Reactive Tracer Methods for Measurement of Thermal Evolution in Geothermal Reservoirs: Final Report

    SciTech Connect (OSTI)

    Mitchell A. Plummer; Carl D. Palmer; Earl D. Mattson; Laurence C. Hull; George D. Redden

    2011-07-01T23:59:59.000Z

    The injection of cold fluids into engineered geothermal system (EGS) and conventional geothermal reservoirs may be done to help extract heat from the subsurface or to maintain pressures within the reservoir (e.g., Rose et al., 2001). As these injected fluids move along fractures, they acquire heat from the rock matrix and remove it from the reservoir as they are extracted to the surface. A consequence of such injection is the migration of a cold-fluid front through the reservoir (Figure 1) that could eventually reach the production well and result in the lowering of the temperature of the produced fluids (thermal breakthrough). Efficient operation of an EGS as well as conventional geothermal systems involving cold-fluid injection requires accurate and timely information about thermal depletion of the reservoir in response to operation. In particular, accurate predictions of the time to thermal breakthrough and subsequent rate of thermal drawdown are necessary for reservoir management, design of fracture stimulation and well drilling programs, and forecasting of economic return. A potential method for estimating migration of a cold front between an injection well and a production well is through application of reactive tracer tests, using chemical whose rate of degradation is dependent on the reservoir temperature between the two wells (e.g., Robinson 1985). With repeated tests, the rate of migration of the thermal front can be determined, and the time to thermal breakthrough calculated. While the basic theory behind the concept of thermal tracers has been understood for some time, effective application of the method has yet to be demonstrated. This report describes results of a study that used several methods to investigate application of reactive tracers to monitoring the thermal evolution of a geothermal reservoir. These methods included (1) mathematical investigation of the sensitivity of known and hypothetical reactive tracers, (2) laboratory testing of novel tracers that would improve method sensitivity, (3) development of a software tool for design and interpretation of reactive tracer tests and (4) field testing of the reactive tracer temperature monitoring concept.

  20. Synthesis, characterization, and reactivity studies of iridium complexes bearing the ligand diphenylphosphidoboratabenzene

    E-Print Network [OSTI]

    Arizpe, Luis (Luis Alfredo)

    2011-01-01T23:59:59.000Z

    The synthesis, structure, and reactivity properties of three iridium square planar complexes bearing the anionic phosphine ligand diphenylphosphidoboratabenzene (DPB) are described. Reactivity studies show a rate enhancement ...

  1. Reactivity of iron-bearing minerals and CO2 sequestration: A...

    Office of Scientific and Technical Information (OSTI)

    Reactivity of iron-bearing minerals and CO2 sequestration: A multi-disciplinary experimental approach Re-direct Destination: The reactivity of sandstones was studied under...

  2. Aging Enhances the Production of Reactive Oxygen Species andBactericid...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Enhances the Production of Reactive Oxygen Species andBactericidal Activity in Peritoneal Macrophages by Aging Enhances the Production of Reactive Oxygen Species andBactericidal...

  3. Metal-Pyrrolide Complexes in Three-fold Symmetry: Synthesis, Structure, Reactivity and Magnetism

    E-Print Network [OSTI]

    Harman, William Hill

    2010-01-01T23:59:59.000Z

    Structure, Reactivity and Magnetism by William Hill Harman AStructure, Reactivity and Magnetism by William Hill Harmanlost time. Dave taught me magnetism and what it takes to win

  4. Effect of shape reactivity on the rod-ejection accident

    SciTech Connect (OSTI)

    Neogy, P.; Carew, J.F.

    1982-09-01T23:59:59.000Z

    The shape reactivity has a significant influence on the rod ejection accident. After the control rod is fully ejected from the core, the neutron flux undergoes a large reduction at the ejected rod location. The corresponding effect on the control reactivity is comparable in magnitude to the Doppler reactivity, and makes a significant contribution to limiting the power excursion during the transient. The neglect of this effect in point kinetics and space time synthesis analyses of the rod ejection accident may account in part for the large degree of conservatism usually associated with these analyses.

  5. Reactive Diffracting Trees Giovanni DellaLibera

    E-Print Network [OSTI]

    Shavit, Nir

    . Their empirical performance under heavy load surpasses all other shared counter implementations. However on individual memory locations, allowing for better performance at high loads. The software combining methods.I.T. A shared counter is a concurrent object that provides a fetch­and­increment operation in a dis­ tributed

  6. Reactivity Accountability Attributed to Reflector Poisons in the High Flux Isotope Reactor

    SciTech Connect (OSTI)

    Chandler, David [ORNL; Maldonado, G Ivan [ORNL; Primm, Trent [ORNL

    2009-12-01T23:59:59.000Z

    The objective of this study is to develop a methodology to predict the reactivity impact as a function of outage time between cycles of 3He, 6Li, and other poisons in the High Flux Isotope Reactor s (HFIR) beryllium reflector. The reactivity worth at startup of the HFIR has been incorrectly predicted in the past after the reactor has been shut-down for long periods of time. The incorrect prediction was postulated to be due to the erroneous calculation of 3He buildup in the beryllium reflector. It is necessary to develop a better estimate of the start-of-cycle symmetric critical control element positions since if the estimated and actual symmetrical critical control element positions differ by more than $1.55 in reactivity (approximately one-half inch in control element startup position), HFIR is to be shutdown and a technical evaluation is performed to resolve the discrepancy prior to restart. 3He is generated and depleted during operation, but during an outage, the depletion of 3He ceases because it is a stable isotope. 3He is born from the radioactive decay of tritium, and thus the concentration of 3He increases during shutdown. SCALE, specifically the TRITON and CSAS5 control modules including the KENO V.A, COUPLE, and ORIGEN functional modules were utilized in this study. An equation relating the down time (td) to the change in symmetric control element position was generated and validated against measurements for approximately 40 HFIR operating cycles. The newly-derived correlation was shown to improve accuracy of predictions for long periods of down time.

  7. REAL TIME SYSTEM OPERATIONS 2006-2007

    E-Print Network [OSTI]

    Eto, Joseph H.

    2008-01-01T23:59:59.000Z

    Reactive Power Reserve Work Group, Western Electricity Reactive  North  American  Electric  Reliability  Corporation  –  Western  Electricity Reactive  Voltage Security Assessment  Western Area Power Administration  Wide?area Security Assessment  Western Electricity 

  8. Reactive Blast Waves from Composite Charges

    SciTech Connect (OSTI)

    Kuhl, A L; Bell, J B; Beckner, V E

    2009-10-16T23:59:59.000Z

    Investigated here is the performance of composite explosives - measured in terms of the blast wave they drive into the surrounding environment. The composite charge configuration studied here was a spherical booster (1/3 charge mass), surrounded by aluminum (Al) powder (2/3 charge mass) at an initial density of {rho}{sub 0} = 0.604 g/cc. The Al powder acts as a fuel but does not detonate - thereby providing an extreme example of a 'non-ideal' explosive (where 2/3 of the charge does not detonate). Detonation of the booster charge creates a blast wave that disperses the Al powder and ignites the ensuing Al-air mixture - thereby forming a two-phase combustion cloud embedded in the explosion. Afterburning of the booster detonation products with air also enhances and promotes the Al-air combustion process. Pressure waves from such reactive blast waves have been measured in bomb calorimeter experiments. Here we describe numerical simulations of those experiments. A Heterogeneous Continuum Model was used to model the dispersion and combustion of the Al particle cloud. It combines the gasdynamic conservation laws for the gas phase with a dilute continuum model for the dispersed phase, as formulated by Nigmatulin. Inter-phase mass, momentum and energy exchange are prescribed by phenomenological models of Khasainov. It incorporates a combustion model based on mass conservation laws for fuel, air and products; source/sink terms are treated in the fast-chemistry limit appropriate for such gasdynamic fields, along with a model for mass transfer from the particle phase to the gas. The model takes into account both the afterburning of the detonation products of the booster with air, and the combustion of the Al particles with air. The model equations were integrated by high-order Godunov schemes for both the gas and particle phases. Adaptive Mesh Refinement (AMR) was used to capture the energy-bearing scales of the turbulent flow on the computational grid, and to track/resolve reaction zones. Numerical simulations of the explosion fields from 1.5-g and 10-kg composite charges were performed. Computed pressure histories (red curve) are compared with measured waveforms (black curves) in Fig. 1. Comparison of these results with a waveform for a non-combustion case in nitrogen (blue curve) demonstrates that a reactive blast wave was formed. Cross-sectional views of the temperature field at various times are presented in Fig. 2, which shows that the flow is turbulent. Initially, combustion occurs at the fuel-air interface, and the energy release rate is controlled by the rate of turbulent mixing. Eventually, oxidizer becomes distributed throughout the cloud via ballistic mixing of the particles with air; energy release then occurs in a distributed combustion mode, and Al particle kinetics controls the energy release rate. Details of the Heterogeneous Continuum Model and results of the numerical simulations of composite charge explosions will be described in the paper.

  9. automatic reactive power: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a radio signal as soon Ning, Peng 62 Active and Reactive Power Control of a DFIG for Variable Speed Wind Energy Conversion using a New Controller CiteSeer Summary: This paper...

  10. Local Control of Reactive Power by Distributed Photovoltaic Generators

    E-Print Network [OSTI]

    Turitsyn, Konstantin S; Backhaus, Scott; Chertkov, Misha

    2010-01-01T23:59:59.000Z

    High penetration levels of distributed photovoltaic (PV) generation on an electrical distribution circuit may severely degrade power quality due to voltage sags and swells caused by rapidly varying PV generation during cloud transients coupled with the slow response of existing utility compensation and regulation equipment. Although not permitted under current standards for interconnection of distributed generation, fast-reacting, VAR-capable PV inverters may provide the necessary reactive power injection or consumption to maintain voltage regulation under difficult transient conditions. As side benefit, the control of reactive power injection at each PV inverter provides an opportunity and a new tool for distribution utilities to optimize the performance of distribution circuits, e.g. by minimizing thermal losses. We suggest a local control scheme that dispatches reactive power from each PV inverter based on local instantaneous measurements of the real and reactive components of the consumed power and the re...

  11. Reactive DC magnetron sputtering of ultrathin superconducting niobium nitride films

    E-Print Network [OSTI]

    Dane, Andrew E. (Andrew Edward)

    2015-01-01T23:59:59.000Z

    DC reactive magnetron sputtering was used to deposit few-nanometer-thick films of niobium nitride for fabrication of superconducting devices. Over 1000 samples were deposited on a variety of substrates, under various chamber ...

  12. Evaluation of Methods to Predict Reactivity of Gold Nanoparticles...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    relationship to the concept of frontier molecular orbital theory. The d-band theory of Hammer and Nørskov is perhaps the most widely used predictor of reactivity on metallic...

  13. Pre-plated reactive diffusion-bonded battery electrode plaques

    DOE Patents [OSTI]

    Maskalick, Nicholas J. (Pittsburgh, PA)

    1984-01-01T23:59:59.000Z

    A high strength, metallic fiber battery plaque is made using reactive diffusion bonding techniques, where a substantial amount of the fibers are bonded together by an iron-nickel alloy.

  14. Reactive oxygen species: a breath of life or death?

    E-Print Network [OSTI]

    Fruehauf, John P; Meyskens, Frank L Jr

    2007-01-01T23:59:59.000Z

    AP1, activator protein-1; ODD, oxygen-dependent degradationSignaling response when oxygen levels decrease (Fig. 1C;3. Halliwell B. Reactive oxygen species in living sys- tems:

  15. Learning Structured Reactive Navigation Plans from Executing MDP Navigation Policies

    E-Print Network [OSTI]

    Cremers, Daniel

    Learning Structured Reactive Navigation Plans from Executing MDP Navigation Policies Michael Beetz, beetz,belker@cs.uni-bonn.de Abstract. Autonomous robots, such as robot office couriers, need navigation

  16. Conversion of carboxylate salts to carboxylic acids via reactive distillation 

    E-Print Network [OSTI]

    Williamson, Shelly Ann

    2000-01-01T23:59:59.000Z

    , municipal solid wastes, sewage sludge, and industrial biosludge. Using a proprietary technology owned by Texas A&M University the wastes are first treated with lime to enhance reactivity. Then they are converted to calcium carboxylate salts using a mixed...

  17. Evolution of Memory in Reactive Artificial Neural Networks

    E-Print Network [OSTI]

    Chung, Ji Ryang

    2012-07-16T23:59:59.000Z

    in the context of evolution: how reactive agents could have evolved into cognitive ones with internalized memory? This study strives to find an answer to the question by simulating neuroevolution on artificial neural networks, with the hypothesis...

  18. Multiphase flow and multicomponent reactive transport model of the ventilation experiment in Opalinus clay

    SciTech Connect (OSTI)

    Zheng, L.; Samper, J.; Montenegro, L.; Major, J.C.

    2008-10-15T23:59:59.000Z

    During the construction and operational phases of a high-level radioactive waste (HLW) repository constructed in a clay formation, ventilation of underground drifts will cause desaturation and oxidation of the rock. The Ventilation Experiment (VE) was performed in a 1.3 m diameter unlined horizontal microtunnel on Opalinus clay at Mont Terri underground research laboratory in Switzerland to evaluate the impact of desaturation on rock properties. A multiphase flow and reactive transport model of VE is presented here. The model accounts for liquid, vapor and air flow, evaporation/condensation and multicomponent reactive solute transport with kinetic dissolution of pyrite and siderite and local-equilibrium dissolution/precipitation of calcite, ferrihydrite, dolomite, gypsum and quartz. Model results reproduce measured vapor flow, liquid pressure and hydrochemical data and capture the trends of measured relative humidities, although such data are slightly overestimated near the rock interface due to uncertainties in the turbulence factor. Rock desaturation allows oxygen to diffuse into the rock and triggers pyrite oxidation, dissolution of calcite and siderite, precipitation of ferrihydrite, dolomite and gypsum and cation exchange. pH in the unsaturated rock varies from 7.8 to 8 and is buffered by calcite. Computed changes in the porosity and the permeability of Opalinus clay in the unsaturated zone caused by oxidation and mineral dissolution/precipitation are smaller than 5%. Therefore, rock properties are not expected to be affected significantly by ventilation of underground drifts during construction and operational phases of a HLW repository in clay.

  19. Development of reactivity feedback effect measurement techniques under sub-critical condition in fast reactors

    SciTech Connect (OSTI)

    Kitano, A.; Nishi, H. [Japan Atomic Energy Agency, 1 1, Shiraki, Tsuruga-shi, Fukui-ken, 919-1279 (Japan); Suzuki, T. [Japan Atomic Energy Agency, 2-4, Shirakata-Shirane, Tokai-mura, Naka-gun, Ibaraki-ken, 319-1195 (Japan); Okajima, S.; Kanemoto, S. [Univ. of Aizu, Tsuruga, Ikki-machi, Aizu-Wakamatsu-shi, Fukushima-ken, 965-8580 (Japan)

    2012-07-01T23:59:59.000Z

    The first-of-a-kind reactor has been licensed by a safety examination of the plant design based on the measured data in precedent mock-up experiments. The validity of the safety design can be confirmed without a mock-up experiment, if the reactor feed-back characteristics can be measured before operation, with the constructed reactor itself. The 'Synthesis Method', a systematic and sophisticated method of sub-criticality measurement, is proposed in this work to ensure the safety margin before operation. The 'Synthesis Method' is based on the modified source multiplication method (MSM) combined with the noise analysis method to measure the reference sub-criticality level for MSM. A numerical simulation for the control-rod reactivity worth and the isothermal feed-back reactivity was conducted for typical fast reactors of 100 MWe-size, 300 MWe-size, 750 MWe-size, and 1500 MWe-size to investigate the applicability of Synthesis Method. The number of neutron detectors and their positions necessary for the measurement were investigated for both methods of MSM and the noise analysis by a series of parametric survey calculations. As a result, it was suggested that a neutron detector located above the core center and three or more neutron detectors located above the radial blanket region enable the measurement of sub-criticality within 10% uncertainty from -$0.5 to -$2 and within 15% uncertainty for the deeper sub-criticality. (authors)

  20. Suppression of Tritium Retention in Remote Areas of ITER by Nonperturbative Reactive Gas Injection

    SciTech Connect (OSTI)

    Tabares, F. L.; Ferreira, J. A.; Ramos, A. [As Euratom-Ciemat, Av Complutense 22, 28040 Madrid (Spain); Rooij, G. van; Westerhout, J.; Al, R.; Rapp, J. [FOM Instituut voor Plasmafysica Rijnhuizen, EURATOM Association, TEC, PO Box 1207, 3430 BE Nieuwegein (Netherlands); Drenik, A.; Mozetic, M. [As Euratom-MHEST, Institut Jozef Stefan, Jamova cesta 39, 1000 Ljubljana (Slovenia)

    2010-10-22T23:59:59.000Z

    A technique based on reactive gas injection in the afterglow region of the divertor plasma is proposed for the suppression of tritium-carbon codeposits in remote areas of ITER when operated with carbon-based divertor targets. Experiments in a divertor simulator plasma device indicate that a 4 nm/min deposition can be suppressed by addition of 1 Pa{center_dot}m{sup 3} s{sup -1} ammonia flow at 10 cm from the plasma. These results bolster the concept of nonperturbative scavenger injection for tritium inventory control in carbon-based fusion plasma devices, thus paving the way for ITER operation in the active phase under a carbon-dominated, plasma facing component background.

  1. Environmental Information Document: L-reactor reactivation

    SciTech Connect (OSTI)

    Mackey, H.E. Jr. (comp.)

    1982-04-01T23:59:59.000Z

    Purpose of this Environmental Information Document is to provide background for assessing environmental impacts associated with the renovation, restartup, and operation of L Reactor at the Savannah River Plant (SRP). SRP is a major US Department of Energy installation for the production of nuclear materials for national defense. The purpose of the restart of L Reactor is to increase the production of nuclear weapons materials, such as plutonium and tritium, to meet projected needs in the nuclear weapons program.

  2. Semi-Analytical Solutions of One-Dimensional Multispecies Reactive Transport in a Permeable Reactive Barrier-Aquifer System

    E-Print Network [OSTI]

    Mieles, John Michael

    2012-07-16T23:59:59.000Z

    At many sites it has become apparent that most chemicals of concern (COCs) in groundwater are persistent and not effectively treated by conventional remediation methods. In recent years, the permeable reactive barrier (PRB) technology has proven...

  3. Effectiveness of Diesel Oxidation Catalyst in Reducing HC and CO Emissions from Reactivity Controlled Compression Ignition

    SciTech Connect (OSTI)

    Prikhodko, Vitaly Y [ORNL; Curran, Scott [ORNL; Parks, II, James E [ORNL; Wagner, Robert M [ORNL

    2013-01-01T23:59:59.000Z

    Reactivity Controlled Compression Ignition (RCCI) has been shown to allow for diesel-like or better brake thermal efficiency with significant reductions in nitrogen oxide (NOX) particulate matter (PM) emissions. Hydrocarbon (HC) and carbon monoxide (CO) emission levels, on the other hand, are similar to those of port fuel injected gasoline engines. The higher HC and CO emissions combined with the lower exhaust temperatures with RCCI operation present a challenge for current exhaust aftertreatments. The reduction of HC and CO emissions in a lean environment is typically achieved with an oxidation catalyst. In this work, several diesel oxidation catalysts (DOC) with different precious metal loadings were evaluated for effectiveness to control HC and CO emissions from RCCI combustion in a light-duty multi-cylinder engine operating on gasoline and diesel fuels. Each catalyst was evaluated in a steady-state engine operation with temperatures ranging from 160 to 260 C. A shift to a higher light-off temperature was observed during the RCCI operation. In addition to the steady-state experiments, the performances of the DOCs were evaluated during multi-mode engine operation by switching from diesel-like combustion at higher exhaust temperature and low HC/CO emissions to RCCI combustion at lower temperature and higher HC/CO emissions. High CO and HC emissions from RCCI generated an exotherm keeping the catalyst above the light-off temperature.

  4. Application of Partial-Order Methods to Reactive Programs with Event Memorization

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    with event memorization. The reactive systems are specified with an asynchronous reactive language Electre, 3 (2001) 287-316" #12;2 Electre: an Asynchronous Reactive Language with Event Memorization 3 2 of a semantic model of an asyn- chronous reactive language: Electre [PRH92, CR95]. Indeed, this language

  5. Operations and compositions in transrecursive operators

    SciTech Connect (OSTI)

    Burgin, M.S.; Borodyanskii, Yu.M.

    1995-03-01T23:59:59.000Z

    The present study is a continuation of a study focusing on introduction and analysis of operations on transrecursive operators, which are similar to the operators considered in the theory of algorithms. Such operations may be standard product of algorithms) or special ({alpha}-disjunction and {alpha}-iteration. In some respects, these operations in the class of transrecursive operators are similar to their traditional analogs. In other respects, however, they are essentially different. For instance, they may have different types and modes. Specific features of operations on transrecursive operators are attributable to explicit omission of some restrictions on their construction compared with the construction of algorithms. The standard approaches to mathematical modeling of the concept of algorithm assume a number of essential restrictions. Specifically, they assume finiteness of (1) the input data arriving during a finite time interval; (2) the list of rules underlying the operations of the algorithm; (3) the transformations executed by a single operation; (4) the description of each rule; (5) the time to execute one operation; (6) the time to execute one operation; (7) the number of cycles that the algorithm executes in order to realize the mapping. In application to Turing machines, these restrictions imply finiteness of the initial word, finiteness of the command table of the read head, and ultimate stopping when the result is obtained after finitely many steps. Various classes of transrecursive operators are constructed by dropping various combinations of the {open_quotes}finiteness{close_quotes} restrictions. Two classes of transrecursive operators - the limit (inductive) Turing machines and transalgorithms - have been obtained by dropping respectively the assumption of finiteness of the number of execution cycles and the assumption of finiteness of the list of rules.

  6. Operating Permits (New Jersey)

    Broader source: Energy.gov [DOE]

    The owner or operator of a facility subject to this article shall obtain and maintain an operating permit for the facility. The owner or operator of a facility subject to this article shall ensure...

  7. Cogeneration Operational Issues

    E-Print Network [OSTI]

    Williams, M.

    operations. Other operational issues also include utility transmission planning, generation planning and fuel mix decisions. All of these operational problems have an impact on the ratepayer in regard to quality of electric service and future rates. Both...

  8. Heat Transfer Operators Associated with Quantum Operations

    E-Print Network [OSTI]

    Ç. Aksak; S. Turgut

    2011-04-14T23:59:59.000Z

    Any quantum operation applied on a physical system is performed as a unitary transformation on a larger extended system. If the extension used is a heat bath in thermal equilibrium, the concomitant change in the state of the bath necessarily implies a heat exchange with it. The dependence of the average heat transferred to the bath on the initial state of the system can then be found from the expectation value of a hermitian operator, which is named as the heat transfer operator (HTO). The purpose of this article is the investigation of the relation between the HTOs and the associated quantum operations. Since, any given quantum operation on a system can be realized by different baths and unitaries, many different HTOs are possible for each quantum operation. On the other hand, there are also strong restrictions on the HTOs which arise from the unitarity of the transformations. The most important of these is the Landauer erasure principle. This article is concerned with the question of finding a complete set of restrictions on the HTOs that are associated with a given quantum operation. An answer to this question has been found only for a subset of quantum operations. For erasure operations, these characterizations are equivalent to the generalized Landauer erasure principle. For the case of generic quantum operations however, it appears that the HTOs obey further restrictions which cannot be obtained from the entropic restrictions of the generalized Landauer erasure principle.

  9. Building Operator Certification

    E-Print Network [OSTI]

    Lilley, D.

    2013-01-01T23:59:59.000Z

    Building Operator Certification Energy Efficiency through Operator Training CATEE December 18, 2013 – San Antonio, TX Dennis Lilley, CEM, PMP ESL-KT-13-12-49 CATEE 2013: Clean Air Through Energy Efficiency Conference, San Antonio, Texas Dec. 16...-18 Building Operator Certification Energy Efficiency through Operator Training What is Building Operator Certification? Industry-recognized credential in energy efficient building operation practices Created with 100 industry experts Launched in 1996 9...

  10. Voltage/Pitch Control for Maximization and Regulation of Active/Reactive Powers in Wind Turbines with Uncertainties

    E-Print Network [OSTI]

    Guo, Yi; Jiang, John N; Tang, Choon Yik; Ramakumar, Rama G

    2010-01-01T23:59:59.000Z

    This paper addresses the problem of controlling a variable-speed wind turbine with a Doubly Fed Induction Generator (DFIG), modeled as an electromechanically-coupled nonlinear system with rotor voltages and blade pitch angle as its inputs, active and reactive powers as its outputs, and most of the aerodynamic and mechanical parameters as its uncertainties. Using a blend of linear and nonlinear control strategies (including feedback linearization, pole placement, uncertainty estimation, and gradient-based potential function minimization) as well as time-scale separation in the dynamics, we develop a controller that is capable of maximizing the active power in the Maximum Power Tracking (MPT) mode, regulating the active power in the Power Regulation (PR) mode, seamlessly switching between the two modes, and simultaneously adjusting the reactive power to achieve a desired power factor. The controller consists of four cascaded components, uses realistic feedback signals, and operates without knowledge of the C_p-...

  11. Magnitude and reactivity consequences of moisture ingress into the modular High-Temperature Gas-Cooled Reactor core

    SciTech Connect (OSTI)

    Smith, O.L. (Oak Ridge National Lab., TN (United States))

    1992-12-01T23:59:59.000Z

    Inadvertent admission of moisture into the primary system of a modular high-temperature gas-cooled reactor has been identified in US Department of Energy-sponsored studies as an important safety concern. The work described here develops an analytical methodology to quantify the pressure and reactivity consequences of steam-generator tube rupture and other moisture-ingress-related incidents. Important neutronic and thermohydraulic processes are coupled with reactivity feedback and safety and control system responses. The rate and magnitude of steam buildup are found to be dominated by major system features such as break size compared with safety valve capacity and reliability and less sensitive to factors such as heat transfer coefficients. The results indicate that ingress transients progress at a slower pace than previously predicted by bounding analyses, with milder power overshoots and more time for operator or automatic corrective actions.

  12. Operation and Maintenance

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Operations and Maintenance Operations OASIS: WALC-DSW (Note: this site is not hosted by Western and requires a digital certificate and login for full access.) Contact Information...

  13. Operations Information for Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Operations Information for Studies This page contains historical information about hydropower operations. Reclamation UC Region 24-Month Studies FY2009 Load Information (pdf) SLIP...

  14. Operations Cost Allocation Project

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Operations Consolidation Project Operations Consolidation Project (OCP) Cost Allocation Presentation - September 20, 2011 OCP Cost Allocation Customer Presentation List of Acronyms...

  15. Operations Research Analyst

    Broader source: Energy.gov [DOE]

    The incumbent in this position will serve as an Operations Research Analyst in the Generation Scheduling (PGS). The Operations Research Analyst is responsible for analytical work that involves...

  16. Environmentally stable reactive alloy powders and method of making same

    DOE Patents [OSTI]

    Anderson, I.E.; Lograsso, B.K.; Terpstra, R.L.

    1998-09-22T23:59:59.000Z

    Apparatus and method are disclosed for making powder from a metallic melt by atomizing the melt to form droplets and reacting the droplets downstream of the atomizing location with a reactive gas. The droplets are reacted with the gas at a temperature where a solidified exterior surface is formed thereon and where a protective refractory barrier layer (reaction layer) is formed whose penetration into the droplets is limited by the presence of the solidified surface so as to avoid selective reduction of key reactive alloys needed to achieve desired powder end use properties. The barrier layer protects the reactive powder particles from environmental constituents such as air and water in the liquid or vapor form during subsequent fabrication of the powder to end-use shapes and during use in the intended service environment. 7 figs.

  17. Options for Control of Reactive Power by Distributed Photovoltaic Generators

    E-Print Network [OSTI]

    Sulc, Petr; Backhaus, Scott; Chertkov, Michael

    2010-01-01T23:59:59.000Z

    High penetration levels of distributed photovoltaic(PV) generation on an electrical distribution circuit present several challenges and opportunities for distribution utilities. Rapidly varying irradiance conditions may cause voltage sags and swells that cannot be compensated by slowly responding utility equipment resulting in a degradation of power quality. Although not permitted under current standards for interconnection of distributed generation, fast-reacting, VAR-capable PV inverters may provide the necessary reactive power injection or consumption to maintain voltage regulation under difficult transient conditions. As side benefit, the control of reactive power injection at each PV inverter provides an opportunity and a new tool for distribution utilities to optimize the performance of distribution circuits, e.g. by minimizing thermal losses. We discuss and compare via simulation various design options for control systems to manage the reactive power generated by these inverters. An important design de...

  18. Apparatus for making environmentally stable reactive alloy powders

    DOE Patents [OSTI]

    Anderson, I.E.; Lograsso, B.K.; Terpstra, R.L.

    1996-12-31T23:59:59.000Z

    Apparatus and method are disclosed for making powder from a metallic melt by atomizing the melt to form droplets and reacting the droplets downstream of the atomizing location with a reactive gas. The droplets are reacted with the gas at a temperature where a solidified exterior surface is formed thereon and where a protective refractory barrier layer (reaction layer) is formed whose penetration into the droplets is limited by the presence of the solidified surface so as to avoid selective reduction of key reactive alloyants needed to achieve desired powder end use properties. The barrier layer protects the reactive powder particles from environmental constituents such as air and water in the liquid or vapor form during subsequent fabrication of the powder to end-use shapes and during use in the intended service environment. 7 figs.

  19. TS525 Construction Total Station

    E-Print Network [OSTI]

    Ahmad, Sajjad

    generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance limits for radio noise emissions from digital apparatus as set out in the radio interference regulations brouillage radioélectrique édicté par le Ministère des Communications du Canada. Europe This product has been

  20. Ts&Cs FP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesisAppliancesTrending:Schedule FYHousehold

  1. Ts&Cs FP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesisAppliancesTrending:Schedule FYHousehold0-09)

  2. Ts&Cs FP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesisAppliancesTrending:Schedule

  3. Minimization of DC Reactor and Operation Characteristics of Direct-Power-Controlled Current-Source PWM Rectifier

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    Minimization of DC Reactor and Operation Characteristics of Direct-Power-Controlled Current describes a direct-power-controlled current-source PWM rectifier, and presents operation characteristics modes on the basis of a relay control technique of instantaneous active and reactive power, using

  4. Dielectric covered hairpin probe for its application in reactive plasmas

    SciTech Connect (OSTI)

    Gogna, G. S.; Gaman, C.; Turner, M. M. [NCPST, School of Physical Sciences, Dublin City University, Dublin 9 (Ireland); Karkari, S. K. [Institute for Plasma Research Center, Bhat Gandhinagar, Gujarat 382428 (India)

    2012-07-23T23:59:59.000Z

    The hairpin probe is a well known technique for measuring local electron density in low temperature plasmas. In reactive plasmas, the probe characteristics are affected by surface sputtering, contamination, and secondary electron emission. At higher densities, the plasma absorbs the entire electromagnetic energy of hairpin and hence limits the density measurements. These issues can be resolved by covering the hairpin surface with a thin layer of dielectric. In this letter, the dielectric contribution to the probe characteristics is incorporated in a theory which is experimentally verified. The dielectric covering improves the performance of probe and also allows the hairpin tip to survive in reactive plasma where classical electrical probes are easily damaged.

  5. Plasma & reactive ion etching to prepare ohmic contacts

    DOE Patents [OSTI]

    Gessert, Timothy A. (Conifer, CO)

    2002-01-01T23:59:59.000Z

    A method of making a low-resistance electrical contact between a metal and a layer of p-type CdTe surface by plasma etching and reactive ion etching comprising: a) placing a CdS/CdTe layer into a chamber and evacuating said chamber; b) backfilling the chamber with Argon or a reactive gas to a pressure sufficient for plasma ignition; and c) generating plasma ignition by energizing a cathode which is connected to a power supply to enable the plasma to interact argon ions alone or in the presence of a radio-frequency DC self-bias voltage with the p-CdTe surface.

  6. The relative reactivity of formic esters with aromatic amines

    E-Print Network [OSTI]

    Markley, Max C.

    1922-01-01T23:59:59.000Z

    .MARKLEY I Vies* S ma y c . l k f c V i M t s RDQOSS 38M30 PREFACE. The purpose of this thesis was to determine the relative reactivity between aromatic amines and the esters of formic acid.It was proposed to first: deter­ mine the reactivity... be given Br .Ray Q,.Brewster , the director of this work, for his help and directions for carrying out this work, and to Br.Prank B.Bains for his kind assistance in many ways. 1.Broil,Journal fur Practische Chemie,1875,vol. 12,page 208. ( 2 ) TABLE...

  7. NUCLEAR PLANT OPERATIONS AND

    E-Print Network [OSTI]

    Pázsit, Imre

    NUCLEAR PLANT OPERATIONS AND CONTROL KEYWORDS: neutron flux, cur- rent noise, vibration diagnostics: Swedish Nuclear Powe

  8. OPERATIONS MANAGEMENT Spring 2008

    E-Print Network [OSTI]

    Almor, Amit

    the operations and supply chain strategy. This survey course in operations management introduces students1 MGSC 395 OPERATIONS MANAGEMENT Spring 2008 Course Syllabus Instructor: Professor Anand Nair Class MATERIALS Required Text Books Textbook: Krajewski, Lee, Ritzman, Larry, and Malhotra, Manoj. Operations

  9. Comparison of Reactivity Control Systems for the Submersion Subcritical Safe Space (S and 4) Reactor

    SciTech Connect (OSTI)

    Schriener, Timothy M.; El-Genk, Mohamed S. [Institute for Space and Nuclear Power Studies and Chemical and Nuclear Engineering Dept., University of New Mexico, Albuquerque, NM 87131 (United States)

    2008-01-21T23:59:59.000Z

    This paper compares the effectiveness of two control mechanisms for the S and 4 reactor, namely: (a) rotating BeO drums with 120 deg. thin segments of enriched B{sub 4}C in the radial reflector; and (b) sliding windows in the radial reflector. Investigated are the effects of using these control mechanisms on the differential reactor control worth, power generation profiles, and spatial neutrons flux distributions is the S and 4 reactor. For both control mechanism, the radial reflector has the same dimensions and volume. Results show that the difference in reactor performance with the two control mechanisms is small. The sliding reflector configuration features slightly lower mass and power peaking, and relatively more even fission power profiles in the core. The differential control worth for the sliding reflector segments is almost constant compared to that using rotating control drums, potentially simplifying the reactor control operation. The presence of a strong neutron absorber in the rotating drums slightly decreases the amount of excess reactivity at BOL compared with the sliding reflector configuration. However, the higher rate of reactivity depletion in the S and 4 reactor with the latter may negate this advantage.

  10. Operator pencil passing through a given operator

    SciTech Connect (OSTI)

    Biggs, A., E-mail: khudian@manchester.ac.uk, E-mail: adam.biggs@student.manchester.ac.uk; Khudaverdian, H. M., E-mail: khudian@manchester.ac.uk, E-mail: adam.biggs@student.manchester.ac.uk [School of Mathematics, University of Manchester, Oxford Road, Manchester M13 9PL (United Kingdom)

    2013-12-15T23:59:59.000Z

    Let ? be a linear differential operator acting on the space of densities of a given weight ?{sub 0} on a manifold M. One can consider a pencil of operators ?-circumflex(?)=(?{sub ?}) passing through the operator ? such that any ?{sub ?} is a linear differential operator acting on densities of weight ?. This pencil can be identified with a linear differential operator ?-circumflex acting on the algebra of densities of all weights. The existence of an invariant scalar product in the algebra of densities implies a natural decomposition of operators, i.e., pencils of self-adjoint and anti-self-adjoint operators. We study lifting maps that are on one hand equivariant with respect to divergenceless vector fields, and, on the other hand, with values in self-adjoint or anti-self-adjoint operators. In particular, we analyze the relation between these two concepts, and apply it to the study of diff?(M)-equivariant liftings. Finally, we briefly consider the case of liftings equivariant with respect to the algebra of projective transformations and describe all regular self-adjoint and anti-self-adjoint liftings. Our constructions can be considered as a generalisation of equivariant quantisation.

  11. Development of Highly Durable and Reactive Regenerable Magnesium-Based Sorbents for CO2 Separation in Coal Gasification Process

    SciTech Connect (OSTI)

    Javad Abbasian; Armin Hassanzadeh Khayyat; Rachid B. Slimane

    2005-06-01T23:59:59.000Z

    The specific objective of this project was to develop physically durable and chemically regenerable MgO-based sorbents that can remove carbon dioxide from raw coal gas at operating condition prevailing in IGCC processes. A total of sixty two (62) different sorbents were prepared in this project. The sorbents were prepared either by various sol-gel techniques (22 formulations) or modification of dolomite (40 formulations). The sorbents were prepared in the form of pellets and in granular forms. The solgel based sorbents had very high physical strength, relatively high surface area, and very low average pore diameter. The magnesium content of the sorbents was estimated to be 4-6 % w/w. To improve the reactivity of the sorbents toward CO{sub 2}, The sorbents were impregnated with potassium salts. The potassium content of the sorbents was about 5%. The dolomite-based sorbents were prepared by calcination of dolomite at various temperature and calcination environment (CO{sub 2} partial pressure and moisture). Potassium carbonate was added to the half-calcined dolomite through wet impregnation method. The estimated potassium content of the impregnated sorbents was in the range of 1-6% w/w. In general, the modified dolomite sorbents have significantly higher magnesium content, larger pore diameter and lower surface area, resulting in significantly higher reactivity compared to the sol-gel sorbents. The reactivities of a number of sorbents toward CO{sub 2} were determined in a Thermogravimetric Analyzer (TGA) unit. The results indicated that at the low CO{sub 2} partial pressures (i.e., 1 atm), the reactivities of the sorbents toward CO{sub 2} are very low. At elevated pressures (i.e., CO{sub 2} partial pressure of 10 bar) the maximum conversion of MgO obtained with the sol-gel based sorbents was about 5%, which corresponds to a maximum CO{sub 2} absorption capacity of less than 1%. The overall capacity of modified dolomite sorbents were at least one order of magnitude higher than those of the sol-gel based sorbents. The results of the tests conducted with various dolomite-based sorbent indicate that the reactivity of the modified dolomite sorbent increases with increasing potassium concentration, while higher calcination temperature adversely affects the sorbent reactivity. Furthermore, the results indicate that as long as the absorption temperature is well below the equilibrium temperature, the reactivity of the sorbent improves with increasing temperature (350-425 C). As the temperature approaches the equilibrium temperature, because of the significant increase in the rate of reverse (i.e., regeneration) reaction, the rate of CO{sub 2} absorption decreases. The results of cyclic tests show that the reactivity of the sorbent gradually decreases in the cyclic process. To improve long-term durability (i.e., reactivity and capacity) of the sorbent, the sorbent was periodically re-impregnated with potassium additive and calcined. The results indicate that, in general, re-treatment improves the performance of the sorbent, and that, the extent of improvement gradually decreases in the cyclic process. The presence of steam significantly enhances the sorbent reactivity and significantly decreases the rate of decline in sorbent deactivation in the cyclic process.

  12. Non-Energetic Reactive Armor (NERA) and Semi-Energetic Reactive Armor (SERA) FY13 Final Report

    SciTech Connect (OSTI)

    Ben Langhorst; Nikki Rasmussen; Andrew Robinson

    2013-08-01T23:59:59.000Z

    INL researchers have proposed prototypes for future lightweight armor systems that reside in a technology gap between explosive reactive armor and passive armor. The targets were designed to react under impact and throw a steel front plate into the path of the projectile, forcing the projectile to engage more of the front plate during its penetration process. These prototypes are intended to exhibit the enhanced efficiency of explosive reactive armor without the collateral damage often associated with explosive reactive armor. One of the prototype systems, Semi Energetic Reactive Armor (SERA), functions similarly to explosive reactive armor, but features a reactive material that reacts much slower than explosive reactive armor. Two different SERA test groups were built and featuring different ratios of aluminum Teflon(copyright) powders pressed into 0.5 in. thick energetic tiles and sandwiched between 0.25 in. thick RHA plates. The other prototype system, Non Energetic Reactive Armor (NERA), utilizes the strain energy in compressed rubber to launch a front flyer plate into the path of an incoming projectile. It is comprised of a 1 in. thick rubber layer sandwiched between two 0.25 in. thick RHA plates with bolt holes around the perimeter. Bolts are inserted through the entire target and tightened to compress the rubber sheet to significant strain levels (approximately 40%). A fourth group of targets was tested as a control group. It featured a 0.5 in. thick rubber sheet sandwiched between two 0.25 in. thick RHA plates, similar to the NERA test articles, but the rubber is uncompressed. The four test groups (uncompressed rubber, compressed rubber, 70/30 Al/PTFE, 50/50 Al/PTFE) were each fabricated with three identical test articles in each group. All twelve targets were subjected to ballistic testing at the National Security Test Range on July 17, 2013. They were tested with 0.5 in. diameter steel rods shot at a consistent velocity at each target. In order to characterize the energetic materials, break wires were embedded in the targets and burn velocities were measured. The residual mass method was used to compare the target performance of each group and final performance data is presented below.

  13. Application of reactive transport modelling to growth and transport of microorganisms in the capillary fringe

    E-Print Network [OSTI]

    Hron, Pavel; Bastian, Peter; Gallert, Claudia; Winter, Josef; Ippisch, Olaf

    2014-01-01T23:59:59.000Z

    A multicomponent multiphase reactive transport simulator has been developed to facilitate the investigation of a large variety of phenomena in porous media including component transport, diffusion, microbiological growth and decay, cell attachment and detachment and phase exchange. The coupled problem is solved using operator splitting. This approach allows a flexible adaptation of the solution strategy to the concrete problem. Moreover, the individual submodels were optimised to be able to describe behaviour of Escherichia coli (HB101 K12 pGLO) in the capillary fringe in the presence or absence of dissolved organic carbon and oxygen under steady-state and flow conditions. Steady-state and flow through experiments in a Hele-Shaw cell, filled with quartz sand, were conducted to study eutrophic bacterial growth and transport in both saturated and unsaturated porous media. As E. coli cells can form the green fluorescent protein (GFP), the cell densities, calculated by evaluation of measured fluorescence intensit...

  14. Effect of Number of Fractionating Trays on Reactive Distillation Performance

    E-Print Network [OSTI]

    Al-Arfaj, Muhammad A.

    Effect of Number of Fractionating Trays on Reactive Distillation Performance Muhammad A. Al and rectifying sec- tions of a reacti®e distillation column can degrade performance. This effect, if true®e distillation columns cannot use conser®ati®e estimates of tray numbers, that is, we cannot simply add excess

  15. Abduction with Negation as Failure for Active and Reactive Rules

    E-Print Network [OSTI]

    Toni, Francesca

    Abduction with Negation as Failure for Active and Reactive Rules Fariba Sadri and Francesca Toni suggested abductive logic programming as a suitable formalism to represent active databases and intelligent agents. In particular, abducibles in abductive logic programs can be used to repre- sent actions

  16. Author's personal copy Reactivity of lithium exposed graphite surface

    E-Print Network [OSTI]

    Harilal, S. S.

    on the surface [18]. Hence the effect of lithium on plasma­wall interactions is expected to dependAuthor's personal copy Reactivity of lithium exposed graphite surface S.S. Harilal a, *, J in fusion devices [1­5]. For example, wall conditioning with thin lithium layers gives rise to low hydrogen

  17. MARKETS FOR REACTIVE POWER AND RELIABILITY: A WHITE PAPER

    E-Print Network [OSTI]

    1 MARKETS FOR REACTIVE POWER AND RELIABILITY: A WHITE PAPER Engineering and Economics of Electricity Research Group (E3 RG) CORNELL UNIVERSITY E3 RG contributing authors: Robert Thomas, Director the Consortium for Electric Reliability Technology Solutions (CERTS) and in part by the National Science

  18. Melting Alpine Glaciers Enrich High-Elevation Lakes with Reactive

    E-Print Network [OSTI]

    Williamson, Craig E.

    Melting Alpine Glaciers Enrich High-Elevation Lakes with Reactive Nitrogen J A S M I N E E . S A R received May 26, 2010. Accepted May 28, 2010. Alpine glaciers have receded substantially over the last. Our results demonstrate that the presence of glaciers on alpine watersheds more strongly influences NO

  19. Local control of reactive power by distributed photovoltaic generators

    SciTech Connect (OSTI)

    Chertkov, Michael [Los Alamos National Laboratory; Turitsyn, Konstantin [Los Alamos National Laboratory; Sulc, Petr [Los Alamos National Laboratory; Backhaus, Scott [Los Alamos National Laboratory

    2010-01-01T23:59:59.000Z

    High penetration levels of distributed photovoltaic (PV) generation on an electrical distribution circuit may severely degrade power quality due to voltage sags and swells caused by rapidly varying PV generation during cloud transients coupled with the slow response of existing utility compensation and regulation equipment. Although not permitted under current standards for interconnection of distributed generation, fast-reacting, VAR-capable PV inverters may provide the necessary reactive power injection or consumption to maintain voltage regulation under difficult transient conditions. As side benefit, the control of reactive power injection at each PV inverter provides an opportunity and a new tool for distribution utilities to optimize the performance of distribution circuits, e.g. by minimizing thermal losses. We suggest a local control scheme that dispatches reactive power from each PV inverter based on local instantaneous measurements of the real and reactive components of the consumed power and the real power generated by the PVs. Using one adjustable parameter per circuit, we balance the requirements on power quality and desire to minimize thermal losses. Numerical analysis of two exemplary systems, with comparable total PV generation albeit a different spatial distribution, show how to adjust the optimization parameter depending on the goal. Overall, this local scheme shows excellent performance; it's capable of guaranteeing acceptable power quality and achieving significant saving in thermal losses in various situations even when the renewable generation in excess of the circuit own load, i.e. feeding power back to the higher-level system.

  20. Dynamic Reactive Power Control of Isolated Power Systems 

    E-Print Network [OSTI]

    Falahi, Milad

    2012-10-03T23:59:59.000Z

    .................................................................................................... 175? 5.1.? Introduction ............................................................................................. 175? 5.2.? Photovoltaic Source ................................................................................. 176? 5.3.? DFIG... .............................................................................. 53 Figure 3-3 Discrete hybrid automata [78] ................................................................... 55 Figure 3-4 Injection and withdrawal of reactive power from bus n ............................ 69 Figure 3-5 Converting the system...

  1. Active and reactive power in stochastic resonance for energy harvesting

    E-Print Network [OSTI]

    Kubota, Madoka; Hikihara, Takashi

    2015-01-01T23:59:59.000Z

    A power allocation to active and reactive power in stochastic resonance is discussed for energy harvesting from mechanical noise. It is confirmed that active power can be increased at stochastic resonance, in the same way of the relationship between energy and phase at an appropriate setting in resonance.

  2. Structuring and Design of Reactive Systems using RSDS and B

    E-Print Network [OSTI]

    Clark, David

    for the automatic synthesis of controllers from invariants. A case study of a train control system is used, which is aimed at reactive control system development. We define strategies for controller decomposition to illustrate the ideas. #12; 1 Introduction A control algorithm for a discrete event system describes

  3. Field, Laboratory, and Modeling Study of Reactive Transport of

    E-Print Network [OSTI]

    University of New York, Flushing, New York 11367, Department of Marine Chemistry and Geochemistry, Woods Hole Bay, MA, shed light on coupled control of chemistry and hydrology on reactive transport), phosphate (5), and oxyanions of molybdenum (6) and uranium (7, 8) in aquifers. In addition

  4. Surface tension in a reactive binary mixture of incompressible fluids

    E-Print Network [OSTI]

    Struchtrup, Henning

    Surface tension in a reactive binary mixture of incompressible fluids Henning Struchtrup Institute with a distributed form of surface tension. The model describes chemistry, diffusion, viscosity and heat transfer tension at the front. Keywords: Binary mixtures, Surface tension, Irreversible thermodynamics, Hele

  5. Nitrogen dynamics in flow-through microcosms of reactive media.

    E-Print Network [OSTI]

    Vallino, Joseph J.

    wastewater inputs to estuaries is similarly an important issue. Individual wastewater treatments have been University, Worcester MA December 19, 2005 Marine Biological Laboratory 1 #12;Abstract There have been many, the Marine Biological Laboratory is currently testing two experimental permeable reactive barriers along

  6. Laboratory tests in support of the MSRE reactive gas removal system

    SciTech Connect (OSTI)

    Rudolph, J.C.; Del Cul, G.D.; Caja, J.; Toth, L.M.; Williams, D.F.; Thomas, K.S.; Clark, D.E.

    1997-07-01T23:59:59.000Z

    The Molten Salt Reactor Experiment (MSRE) at Oak Ridge National Laboratory has been shut down since December 1969, at which time the molten salt mixture of LiF-BeF{sub 2}-ZrF{sub 4}-{sup 233}UF{sub 4} (64.5-30.3-5.0-0.13 mol%) was transferred to fuel salt drain tanks for storage. In the late 1980s, increased radiation in one of the gas lines from the drain tank was attributed to {sup 233}UF{sub 6}. In 1994 two gas samples were withdraw (from a gas line in the Vent House connecting to the drain tanks) and analyzed. Surprisingly, 350 mm Hg of F{sub 2}, 70 mm Hg of UF{sub 6}, and smaller amounts of other gases were found in both of the samples. To remote this gas from above the drain tanks and all of the associated piping, the reactive gas removal system (RGRS) was designed. This report details the laboratory testing of the RGRS, using natural uranium, prior to its implementation at the MSRE facility. The testing was performed to ensure that the equipment functioned properly and was sufficient to perform the task while minimizing exposure to personnel. In addition, the laboratory work provided the research and development effort necessary to maximize the performance of the system. Throughout this work technicians and staff who were to be involved in RGRS operation at the MSRE site worked directly with the research staff in completing the laboratory testing phase. Consequently, at the end of the laboratory work, the personnel who were to be involved in the actual operations had acquired all of the training and experience necessary to continue with the process of reactive gas removal.

  7. December 13, 2012 The steady state model of a reactive distillation column for ethylene glycol

    E-Print Network [OSTI]

    Neumaier, Arnold

    December 13, 2012 The steady state model of a reactive distillation column for ethylene glycol in an ethylene glycol reactive distillation column. Ind. Eng. Chem. Res., 33:2738­2748, 1994. 3 #12;

  8. Hydrogen Reactivity on Highly-hydroxylated TiO2(110) Surfaces...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reactivity on Highly-hydroxylated TiO2(110) Surfaces Prepared via Carboxylic Acid Adsorption and Photolysis. Hydrogen Reactivity on Highly-hydroxylated TiO2(110) Surfaces Prepared...

  9. Reactive Transport Modeling and Geophysical Monitoring of Bioclogging at Reservoir Scale

    E-Print Network [OSTI]

    Hubbard, Susan

    Reactive Transport Modeling and Geophysical Monitoring of Bioclogging at Reservoir Scale Vikranth scale using a combination of reactive transport modeling and geophysical imaging tools (EM & seismic Sacramento basin, California; the model well (Citizen Green #1) was characterized using sonic, electrical

  10. An Aircraft Electric Power Testbed for Validating Automatically Synthesized Reactive Control Protocols

    E-Print Network [OSTI]

    Xu , Huan

    An Aircraft Electric Power Testbed for Validating Automatically Synthesized Reactive Control reactive synthesis; testbed; aircraft electric power system 1. INTRODUCTION AND MOTIVATION Aircraft of Pennsylvania utopcu@seas.upenn.edu ABSTRACT Modern aircraft increasingly rely on electric power for sub

  11. Stabilization of liquid crystal photoaligning layers by reactive mesogens O. Yaroshchuk,1

    E-Print Network [OSTI]

    Stabilization of liquid crystal photoaligning layers by reactive mesogens O. Yaroshchuk,1 V photoaligning layers by thin layers of reactive mesogens, strong enhancement in LC alignment stability layer, the photoalignment technique minimizes me- chanical damage and electric charging, provides

  12. Pollution-enhanced reactive chlorine chemistry in the eastern tropical Atlantic boundary layer

    E-Print Network [OSTI]

    2009-01-01T23:59:59.000Z

    doi:10.1029/2008GL036666, 2009 Pollution-enhanced reactiveE. S. Saltzman (2009), Pollution-enhanced reactive chlorine5 L08810 LAWLER ET AL. : POLLUTION-ENHANCED CLX IN THE MBL

  13. Chemical Reactivity of Reduced TiO2(110): The dominant role of...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reactivity of Reduced TiO2(110): The dominant role of surface defects in oxygen chemisorption. Chemical Reactivity of Reduced TiO2(110): The dominant role of surface defects in...

  14. Storage Ring Operation Modes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Longitudinal bunch profile and Up: APS Storage Ring Parameters Previous: Source Parameter Table Storage Ring Operation Modes Standard Operating Mode, top-up Fill pattern: 102 mA in...

  15. Aerosol Sampler Operations Manual

    E-Print Network [OSTI]

    Fischer, Emily V.

    -1123 Laboratory FAX (916) 752-4107 Standard Operating Procedures Technical Information Document TI 201A #12;TI 201.................................................................................................................................................. 3 1.0 Weekly Maintenance ProceduresIMPROVE Aerosol Sampler Operations Manual February 10, 1997 Air Quality Group Crocker Nuclear

  16. Climate Data Operators (CDO)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Climate Data Operators (CDO) Climate Data Operators (CDO) Description and Overview CDO is a large tool set for working on climate data. NetCDF 34, GRIB including SZIP compression,...

  17. Reservoir Operation in Texas

    E-Print Network [OSTI]

    Wurbs, Ralph A.

    management of the surface water resources of the various river basins of the state. The operation of these essential water control facilities is examined in this report. Reservoir operation is viewed here from the perspective of deciding how much water...

  18. SWPF Crane Lift Operation

    SciTech Connect (OSTI)

    None

    2010-01-01T23:59:59.000Z

    A multiple vview shot of the SWPF crane lift operation at the Savannah River Site. Funded by the Recovery Act.

  19. Top 100 Operators: Proved Reserves and Production, Operated vs...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Top 100 Operators: Proved Reserves and Production, Operated vs Owned, 2009 1 Top 100 Operators: Proved Reserves and Production, Operated vs Owned, 2009 The operator of an oil or...

  20. Control Study of Ethyl tert-Butyl Ether Reactive Distillation Muhammad A. Al-Arfaj

    E-Print Network [OSTI]

    Al-Arfaj, Muhammad A.

    Control Study of Ethyl tert-Butyl Ether Reactive Distillation Muhammad A. Al-Arfaj Department structures for ethyl tert-butyl ether (ETBE) reactive distillation columns are studied. Two process The use of reactive distillation has grown in recent years because it results in less expensive and more

  1. Analytical solutions for sequentially coupled one-dimensional reactive transport problems Part I: Mathematical derivations

    E-Print Network [OSTI]

    Clement, Prabhakar

    Analytical solutions for sequentially coupled one-dimensional reactive transport problems ­ Part I-species reactive transport equations coupled through sorption and sequential first-order reactions are commonly. Although researchers have been attempting to solve various forms of these reactive transport equations

  2. VOF-BASED SIMULATION OF REACTIVE MASS TRANSFER ACROSS DEFORMABLE INTERFACES

    E-Print Network [OSTI]

    Bothe, Dieter

    . of the bubbles is there- fore of fundamental importance for effective design of the reactor. In case of fast-based approach for the Direct Numerical Simulation of reactive mass transfer in gas-liquid flows is described simulation results are presented for non reactive and reactive mass transfer from rising gas bubbles

  3. Using Reactive Rules to Guide a Forward-Chaining Murray Shanahan

    E-Print Network [OSTI]

    Shanahan, Murray

    1 Using Reactive Rules to Guide a Forward-Chaining Planner Murray Shanahan Department of Electrical.shanahan@ic.ac.uk Keywords: planning and execution, reactive planning, robot planning Abstract This paper presents a planning technique in which a flawed set of reactive rules is used to guide a stochastic forward-chaining search

  4. A pulser for medium-frequency modulated direct-current reactive sputter deposition of insulators

    E-Print Network [OSTI]

    Cao, Hui

    for medium-frequency modulated direct-current dc reactive sputter deposition of electrical insulators at the target surface inherent to high- deposition-rate reactive sputtering of electrical insulators. TypicallyA pulser for medium-frequency modulated direct-current reactive sputter deposition of insulators G

  5. Abstract This paper reviews specific issues and challenges in reactive power management within the competitive electricity

    E-Print Network [OSTI]

    Gross, George

    and physical considerations and so depends on the market players and the electricity market rules. Reactive local nature of reactive power restricts its ability to be transmitted over electrically large distancesAbstract ­ This paper reviews specific issues and challenges in reactive power management within

  6. CARIBBEAN COLLOQUIUM ON POWER QUALITY (CCPQ), JUNE 2003 100 Defining Reactive Power in Circuit Transients via

    E-Print Network [OSTI]

    Stankoviæ, Aleksandar

    CARIBBEAN COLLOQUIUM ON POWER QUALITY (CCPQ), JUNE 2003 100 Defining Reactive Power in Circuit the notion of reactive power during circuit transients. The definition we propose is based on the concept, namely Short- Time Fourier Coefficients and Haar Wavelets. We illustrate this "dynamic" reactive power

  7. Finite Bisimulation of Reactive Untimed Infinite State Systems Modeled as Automata with Variables

    E-Print Network [OSTI]

    Kumar, Ratnesh

    1 Finite Bisimulation of Reactive Untimed Infinite State Systems Modeled as Automata with Variables for reactive untimed infinite state systems called input- output extended finite automaton (I/O-EFA), which of a finite bisimilar abstraction. The results are illustrated through examples that model reactive software

  8. Examination of a PHEV Bidirectional Charger System for V2G Reactive Power Compensation

    E-Print Network [OSTI]

    Tolbert, Leon M.

    . Keywords - PHEV; charger; V2G; reactive power; battery I. INTRODUCTION Today, hybrid electric vehicles and shows how to control the on-board vehicle charger to provide reactive power to the electric grid is not engaged in reactive power transfer. II. ELECTRIC VEHICLE CHARGERS Battery chargers play an important role

  9. Toward Optimized Bioclogging and Biocementation Through Combining Advanced Geophysical Monitoring and Reactive Transport Modeling

    E-Print Network [OSTI]

    Hubbard, Susan

    and electrical techniques); (ii) developing and using a reactive transport simulator capable of predicting and Reactive Transport Modeling Approaches Christopher G Hubbard1 , Susan S. Hubbard1 , Yuxin Wu1 , Vikranth heterogeneities at the field scale. Optimization of these strategies requires advances in mechanistic reactive

  10. Voltage Control of Distribution Networks with Distributed Generation using Reactive Power

    E-Print Network [OSTI]

    Pota, Himanshu Roy

    Voltage Control of Distribution Networks with Distributed Generation using Reactive Power to control voltage of distribution networks with DG using reactive power compensation approach. In this paper profile within the specified limits, it is essential to regulate the reactive power of the compensators

  11. Generation of reactive oxygen species by a persulfide (BnSSH) Tonika Chatterji,

    E-Print Network [OSTI]

    Gates, Kent. S.

    Generation of reactive oxygen species by a persulfide (BnSSH) Tonika Chatterji, Kripa Keerthi generate reactive oxygen species under biologically rele- vant conditions via the sequence of reactions by reactive oxygen species generated in this manner may contribute to the cytotoxic properties of leinamycin

  12. TO APPEAR IN IEEE TRANSACTION ON POWER SYSTEMS 1 Effect of Reactive Power Limit Modeling on

    E-Print Network [OSTI]

    Cañizares, Claudio A.

    TO APPEAR IN IEEE TRANSACTION ON POWER SYSTEMS 1 Effect of Reactive Power Limit Modeling on Maximum System Loading and Active and Reactive Power Markets Behnam Tamimi, Student Member, IEEE, Claudio A. Ca- active power in electric power systems. Although there are other important reactive power sources

  13. Automated Impedance Tomography for Monitoring Permeable Reactive Barrier Health

    SciTech Connect (OSTI)

    LaBrecque, D J; Adkins, P L

    2009-07-02T23:59:59.000Z

    The objective of this research was the development of an autonomous, automated electrical geophysical monitoring system which allows for near real-time assessment of Permeable Reactive Barrier (PRB) health and aging and which provides this assessment through a web-based interface to site operators, owners and regulatory agencies. Field studies were performed at four existing PRB sites; (1) a uranium tailing site near Monticello, Utah, (2) the DOE complex at Kansas City, Missouri, (3) the Denver Federal Center in Denver, Colorado and (4) the Asarco Smelter site in East Helena, Montana. Preliminary surface data over the PRB sites were collected (in December, 2005). After the initial round of data collection, the plan was modified to include studies inside the barriers in order to better understand barrier aging processes. In September 2006 an autonomous data collection system was designed and installed at the EPA PRB and the electrode setups in the barrier were revised and three new vertical electrode arrays were placed in dedicated boreholes which were in direct contact with the PRB material. Final data were collected at the Kansas City, Denver and Monticello, Utah PRB sites in the fall of 2007. At the Asarco Smelter site in East Helena, Montana, nearly continuous data was collected by the autonomous monitoring system from June 2006 to November 2007. This data provided us with a picture of the evolution of the barrier, enabling us to examine barrier changes more precisely and determine whether these changes are due to installation issues or are normal barrier aging. Two rounds of laboratory experiments were carried out during the project. We conducted column experiments to investigate the effect of mineralogy on the electrical signatures resulting from iron corrosion and mineral precipitation in zero valent iron (ZVI) columns. In the second round of laboratory experiments we observed the electrical response from simulation of actual field PRBs at two sites: the Kansas City barrier and the East Helena barrier. As these sites are also used for our field monitoring efforts, this allowed for a comparison between field and laboratory. In column studies with high concentrations of calcium and carbonate/bicarbonate, we observed that the increase of electrical resistivity and decrease of polarization magnitude is significant and is mainly controlled by the precipitation of calcium carbonates. In general, the electrical properties of all of the barriers studied follow a pattern. New barriers are fairly resistive with in-situ conductivity only a few times background (outside the barrier) values. Older barriers get increasingly conductive, with failed barriers showing values of over 100 S/m. The induced polarization response is more complicated. Chargeability values increase over time for young barriers, are largest for healthy barriers in the middle of their lifespan, and decrease as the barrier ages These results suggest that normalized IP appears promising as a measure of barrier age.

  14. Safe Operating Procedure (Revised 7/09)

    E-Print Network [OSTI]

    Farritor, Shane

    -800 4 5 6 8 8 9 10 4 5 6 8 9 12 14 Torch Brazing (TB) -- -- 3 or 4 Torch Soldering (TS) -- -- 2 Carbon zone without going below the minimum. In oxyfuel gas welding, cutting, or brazing where the torch lenses used, since not all brands are the same or provide equal protection against flash. · For laser

  15. Engine combustion control at low loads via fuel reactivity stratification

    DOE Patents [OSTI]

    Reitz, Rolf Deneys; Hanson, Reed M; Splitter, Derek A; Kokjohn, Sage L

    2014-10-07T23:59:59.000Z

    A compression ignition (diesel) engine uses two or more fuel charges during a combustion cycle, with the fuel charges having two or more reactivities (e.g., different cetane numbers), in order to control the timing and duration of combustion. By appropriately choosing the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot). At low load and no load (idling) conditions, the aforementioned results are attained by restricting airflow to the combustion chamber during the intake stroke (as by throttling the incoming air at or prior to the combustion chamber's intake port) so that the cylinder air pressure is below ambient pressure at the start of the compression stroke.

  16. Tracking thermal fronts with temperature-sensitive, chemically reactive tracers

    SciTech Connect (OSTI)

    Robinson, B.A.; Birdsell, S.A.

    1987-01-01T23:59:59.000Z

    Los Alamos is developing tracer techniques using reactive chemicals to track thermal fronts in fractured geothermal reservoirs. If a nonadsorbing tracer flowing from the injection to production well chemically reacts, its reaction rate will be a strong function of temperature. Thus the extent of chemical reaction will be greatest early in the lifetime of the system, and less as the thermal front progresses from the injection to production well. Early laboratory experiments identified tracers with chemical kinetics suitable for reservoirs in the temperature range of 75 to 100/sup 0/C. Recent kinetics studies have focused on the kinetics of hydrolysis of derivatives of bromobenzene. This class of reactions can be used in reservoirs ranging in temperature from 150 to 275/sup 0/C, which is of greater interest to the geothermal industry. Future studies will include laboratory adsorption experiments to identify possibly unwanted adsorption on granite, development of sensitive analytical techniques, and a field demonstration of the reactive tracer concept.

  17. Reactivity impact of delayed neutron spectra on MCNP calculations

    SciTech Connect (OSTI)

    Mosteller, R.D.; Werner, C.J.

    2000-07-01T23:59:59.000Z

    The new features in MCNP4C, the latest version of the MCNP Monte Carlo code, include the capability to sample from delayed as well as prompt fission emission spectra. Previous versions of MCNP all have sampled exclusively from prompt spectra. Delayed neutrons typically account for <1% of all neutrons emitted from fission, but the emission spectra for delayed neutrons are somewhat softer than those for prompt neutrons. Because of the softer spectrum, delayed neutrons are less likely to leak from the system, and they also are less likely to cause fission in isotopes that have an effective threshold for fission (e.g., {sup 238}U and {sup 240}Pu). Consequently, the inclusion of delayed neutron spectra can have a small but significant effect on reactivity calculations. This study performs MCNP4C calculations for a series of established benchmarks and quantifies the reactivity impact of the delayed neutron spectra.

  18. Revised Knudsen-layer reduction of fusion reactivity

    SciTech Connect (OSTI)

    Albright, B. J.; Molvig, Kim; Huang, C.-K.; Simakov, A. N.; Dodd, E. S.; Hoffman, N. M.; Kagan, G. [Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, New Mexico 87545 (United States)] [Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, New Mexico 87545 (United States); Schmit, P. F. [Sandia National Laboratories, P.O. Box 5800, Albuquerque, New Mexico 87185-1186 (United States)] [Sandia National Laboratories, P.O. Box 5800, Albuquerque, New Mexico 87185-1186 (United States)

    2013-12-15T23:59:59.000Z

    Recent work by Molvig et al. [Phys. Rev. Lett. 109, 095001 (2012)] examined how fusion reactivity may be reduced from losses of fast ions in finite assemblies of fuel. In this paper, this problem is revisited with the addition of an asymptotic boundary-layer treatment of ion kinetic losses. This boundary solution, reminiscent of the classical Milne problem from linear transport theory, obtains a free-streaming limit of fast ion losses near the boundary, where the diffusion approximation is invalid. Thermonuclear reaction rates have been obtained for the ion distribution functions predicted by this improved model. It is found that while Molvig's “Knudsen distribution function” bounds from above the magnitude of the reactivity reduction, this more accurate treatment leads to less dramatic losses of tail ions and associated reduction of thermonuclear reaction rates for finite fuel volumes.

  19. Catalytic destruction of groundwater contaminants in reactive extraction wells

    DOE Patents [OSTI]

    McNab, Jr., Walt W. (Concord, CA); Reinhard, Martin (Stanford, CA)

    2002-01-01T23:59:59.000Z

    A system for remediating groundwater contaminated with halogenated solvents, certain metals and other inorganic species based on catalytic reduction reactions within reactive well bores. The groundwater treatment uses dissolved hydrogen as a reducing agent in the presence of a metal catalyst, such a palladium, to reduce halogenated solvents (as well as other substituted organic compounds) to harmless species (e.g., ethane or methane) and immobilize certain metals to low valence states. The reactive wells function by removing water from a contaminated water-bearing zone, treating contaminants with a well bore using catalytic reduction, and then reinjecting the treated effluent into an adjacent water-bearing zone. This system offers the advantages of a compact design with a minimal surface footprint (surface facilities) and the destruction of a broad suite of contaminants without generating secondary waste streams.

  20. Parallel computation of multigroup reactivity coefficient using iterative method

    SciTech Connect (OSTI)

    Susmikanti, Mike [Center for Development of Nuclear Informatics, National Nuclear Energy Agency of Indonesia PUSPIPTEK Area, Tangerang (Indonesia)] [Center for Development of Nuclear Informatics, National Nuclear Energy Agency of Indonesia PUSPIPTEK Area, Tangerang (Indonesia); Dewayatna, Winter [Center for Nuclear Fuel Technology, National Nuclear Energy Agency of Indonesia PUSPIPTEK Area, Tangerang (Indonesia)] [Center for Nuclear Fuel Technology, National Nuclear Energy Agency of Indonesia PUSPIPTEK Area, Tangerang (Indonesia)

    2013-09-09T23:59:59.000Z

    One of the research activities to support the commercial radioisotope production program is a safety research target irradiation FPM (Fission Product Molybdenum). FPM targets form a tube made of stainless steel in which the nuclear degrees of superimposed high-enriched uranium. FPM irradiation tube is intended to obtain fission. The fission material widely used in the form of kits in the world of nuclear medicine. Irradiation FPM tube reactor core would interfere with performance. One of the disorders comes from changes in flux or reactivity. It is necessary to study a method for calculating safety terrace ongoing configuration changes during the life of the reactor, making the code faster became an absolute necessity. Neutron safety margin for the research reactor can be reused without modification to the calculation of the reactivity of the reactor, so that is an advantage of using perturbation method. The criticality and flux in multigroup diffusion model was calculate at various irradiation positions in some uranium content. This model has a complex computation. Several parallel algorithms with iterative method have been developed for the sparse and big matrix solution. The Black-Red Gauss Seidel Iteration and the power iteration parallel method can be used to solve multigroup diffusion equation system and calculated the criticality and reactivity coeficient. This research was developed code for reactivity calculation which used one of safety analysis with parallel processing. It can be done more quickly and efficiently by utilizing the parallel processing in the multicore computer. This code was applied for the safety limits calculation of irradiated targets FPM with increment Uranium.

  1. Dynamics of inelastic and reactive gas-surface collisions

    SciTech Connect (OSTI)

    Smoliar, L.A.

    1995-04-01T23:59:59.000Z

    The dynamics of inelastic and reactive collisions in atomic beam-surface scattering are presented. The inelastic scattering of hyperthermal rare gaseous atoms from three alkali halide surfaces (LiF, NaCl, GI)was studied to understand mechanical energy transfer in unreactive systems. The dynamics of the chemical reaction in the scattering of H(D) atoms from the surfaces of LIF(001) and the basal plane of graphite were also studied.

  2. Reactive Distillation for Esterification of Bio-based Organic Acids

    SciTech Connect (OSTI)

    Fields, Nathan; Miller, Dennis J.; Asthana, Navinchandra S.; Kolah, Aspi K.; Vu, Dung; Lira, Carl T.

    2008-09-23T23:59:59.000Z

    The following is the final report of the three year research program to convert organic acids to their ethyl esters using reactive distillation. This report details the complete technical activities of research completed at Michigan State University for the period of October 1, 2003 to September 30, 2006, covering both reactive distillation research and development and the underlying thermodynamic and kinetic data required for successful and rigorous design of reactive distillation esterification processes. Specifically, this project has led to the development of economical, technically viable processes for ethyl lactate, triethyl citrate and diethyl succinate production, and on a larger scale has added to the overall body of knowledge on applying fermentation based organic acids as platform chemicals in the emerging biorefinery. Organic acid esters constitute an attractive class of biorenewable chemicals that are made from corn or other renewable biomass carbohydrate feedstocks and replace analogous petroleum-based compounds, thus lessening U.S. dependence on foreign petroleum and enhancing overall biorefinery viability through production of value-added chemicals in parallel with biofuels production. Further, many of these ester products are candidates for fuel (particularly biodiesel) components, and thus will serve dual roles as both industrial chemicals and fuel enhancers in the emerging bioeconomy. The technical report from MSU is organized around the ethyl esters of four important biorenewables-based acids: lactic acid, citric acid, succinic acid, and propionic acid. Literature background on esterification and reactive distillation has been provided in Section One. Work on lactic acid is covered in Sections Two through Five, citric acid esterification in Sections Six and Seven, succinic acid in Section Eight, and propionic acid in Section Nine. Section Ten covers modeling of ester and organic acid vapor pressure properties using the SPEAD (Step Potential Equilibrium and Dynamics) method.

  3. Variably Saturated Flow and Multicomponent Biogeochemical Reactive Transport Modeling of a Uranium Bioremediation Field Experiment

    SciTech Connect (OSTI)

    Yabusaki, Steven B.; Fang, Yilin; Williams, Kenneth H.; Murray, Christopher J.; Ward, Anderson L.; Dayvault, Richard; Waichler, Scott R.; Newcomer, Darrell R.; Spane, Frank A.; Long, Philip E.

    2011-11-01T23:59:59.000Z

    Field experiments at a former uranium mill tailings site have identified the potential for stimulating indigenous bacteria to catalyze the conversion of aqueous uranium in the +6 oxidation state to immobile solid-associated uranium in the +4 oxidation state. This effectively removes uranium from solution resulting in groundwater concentrations below actionable standards. Three-dimensional, coupled variably-saturated flow and biogeochemical reactive transport modeling of a 2008 in situ uranium bioremediation field experiment is used to better understand the interplay of transport rates and biogeochemical reaction rates that determine the location and magnitude of key reaction products. A comprehensive reaction network, developed largely through previous 1-D modeling studies, was used to simulate the impacts on uranium behavior of pulsed acetate amendment, seasonal water table variation, spatially-variable physical (hydraulic conductivity, porosity) and geochemical (reactive surface area) material properties. A principal challenge is the mechanistic representation of biologically-mediated terminal electron acceptor process (TEAP) reactions whose products significantly alter geochemical controls on uranium mobility through increases in pH, alkalinity, exchangeable cations, and highly reactive reduction products. In general, these simulations of the 2008 Big Rusty acetate biostimulation field experiment in Rifle, Colorado confirmed previously identified behaviors including (1) initial dominance by iron reducing bacteria that concomitantly reduce aqueous U(VI), (2) sulfate reducing bacteria that become dominant after {approx}30 days and outcompete iron reducers for the acetate electron donor, (3) continuing iron-reducer activity and U(VI) bioreduction during dominantly sulfate reducing conditions, and (4) lower apparent U(VI) removal from groundwater during dominantly sulfate reducing conditions. New knowledge on simultaneously active metal and sulfate reducers has been incorporated into the modeling. In this case, an initially small population of slow growing sulfate reducers is active from the initiation of biostimulation. Three-dimensional, variably saturated flow modeling was used to address impacts of a falling water table during acetate injection. These impacts included a significant reduction in aquifer saturated thickness and isolation of residual reactants and products, as well as unmitigated uranium, in the newly unsaturated vadose zone. High permeability sandy gravel structures resulted in locally high flow rates in the vicinity of injection wells that increased acetate dilution. In downgradient locations, these structures created preferential flow paths for acetate delivery that enhanced local zones of TEAP reactivity and subsidiary reactions. Conversely, smaller transport rates associated with the lower permeability lithofacies (e.g., fine) and vadose zone were shown to limit acetate access and reaction. Once accessed by acetate, however, these same zones limited subsequent acetate dilution and provided longer residence times that resulted in higher concentrations of TEAP products when terminal electron donors and acceptors were not limiting. Finally, facies-based porosity and reactive surface area variations were shown to affect aqueous uranium concentration distributions; however, the ranges were sufficiently small to preserve general trends. Large computer memory and high computational performance were required to simulate the detailed coupled process models for multiple biogeochemical components in highly resolved heterogeneous materials for the 110-day field experiment and 50 days of post-biostimulation behavior. In this case, a highly-scalable subsurface simulator operating on 128 processor cores for 12 hours was used to simulate each realization. An equivalent simulation without parallel processing would have taken 60 days, assuming sufficient memory was available.

  4. Reactivity accidents: A reassessment of the design-basis events

    SciTech Connect (OSTI)

    Diamond, D.J.; Hsu, Chia-Jung; Fitzpatrick, R.; Mirkovic, D.

    1989-01-01T23:59:59.000Z

    This paper summarizes a study of light water reactor event sequences which have been investigated for their potential to result in reactivity accidents with severe consequences. The study is an outgrowth of the concern which arose after the accident at Chernobyl and was recommended by the report of the US Nuclear Regulatory Commission (NRC) on the implications of that accident (NUREG-1251). The work was done for the NRC to reconfirm or bring into question previous judgments on reactivity events which must be analyzed for licensing. Event sequences were defined and then a probabilistic assessment was completed to estimate the frequency of the reactivity event and/or a deterministic calculation was completed to estimate the consequences to the fuel. Using the results of this analysis, analysis done by others, and a set of screening criteria developed within this study, judgments were made for each sequence as to its importance, and recommendations were made as to whether the NRC ought to be considering the important sequences as part of the design basis or for further, more detailed, investigation. 31 refs., 9 figs., 1 tab.

  5. STARTUP REACTIVITY ACCOUNTABILITY ATTRIBUTED TO ISOTOPIC TRANSMUTATIONS IN THE IRRADIATED BERYLLIUM REFLECTOR OF THE HIGH FLUX ISTOTOPE REACTOR

    SciTech Connect (OSTI)

    Chandler, David [ORNL] [ORNL; Maldonado, G Ivan [ORNL] [ORNL; Primm, Trent [ORNL] [ORNL

    2010-01-01T23:59:59.000Z

    The objective of this study is to develop a methodology to predict the reactivity impact as a function of outage time between cycles of 3He, 6Li, and other poisons in the High Flux Isotope Reactor s (HFIR) beryllium reflector. The reactivity worth at startup of the HFIR has been incorrectly predicted in the past after the reactor has been shut-down for long periods of time. The incorrect prediction was postulated to be due to the erroneous calculation of 3He buildup in the beryllium reflector. It is necessary to develop a better estimate of the start-of-cycle symmetric critical control element positions since if the estimated and actual symmetrical critical control element positions differ by more than $1.55 in reactivity (approximately one-half inch in control element startup position), HFIR is to be shutdown and a technical evaluation is performed to resolve the discrepancy prior to restart. 3He is generated and depleted during operation, but during an outage, the depletion of 3He ceases because it is a stable isotope. 3He is born from the radioactive decay of tritium, and thus the concentration of 3He increases during shutdown. The computer program SCALE, specifically the TRITON and CSAS5 control modules including the KENO V.A, COUPLE, and ORIGEN functional modules were utilized in this study. An equation relating the down time (td) to the change in symmetric control element position was generated and validated against measurements for approximately 40 HFIR operating cycles. The newly-derived correlation was shown to improve accuracy of predictions for long periods of down time.

  6. Cask fleet operations study

    SciTech Connect (OSTI)

    Not Available

    1988-01-01T23:59:59.000Z

    The Nuclear Waste Policy Act of 1982 assigned to the Department of Energy's (DOE) Office of Civilian Waste Management the responsibility for disposing of high-level waste and spent fuel. A significant part of that responsibility involves transporting nuclear waste materials within the federal waste management system; that is, from the waste generator to the repository. The lead responsibility for transportation operations has been assigned to Oak Ridge Operations, with Oak Ridge National Laboratory (ORNL) providing technical support through the Transportation Operations Support Task Group. One of the ORNL support activities involves assessing what facilities, equipment and services are required to assure that an acceptable, cost-effective and safe transportation operations system can be designed, operated and maintained. This study reviews, surveys and assesses the experience of Nuclear Assurance Corporation (NAC) in operating a fleet of spent-fuel shipping casks to aid in developing the spent-fuel transportation system.

  7. Apollo Multiplexer operations manual

    SciTech Connect (OSTI)

    Miller, M.M.

    1985-04-01T23:59:59.000Z

    This report describes the operation of the the Apollo Multiplexer, a microprocessor based communications device designed to process data between an Apollo computer and up to four Gandalf PACXIV data switches. Details are given on overall operation, hardware, and troubleshooting. The reader should gain sufficient knowledge from this report to understand the operation of the multiplexer and effectively analyze and correct any problems that might occur.

  8. Real Power and Reactive Power Control of a Three-Phase Single-Stage-PV System and PV voltage Stability

    SciTech Connect (OSTI)

    Li, Huijuan [ORNL] [ORNL; Xu, Yan [ORNL] [ORNL; Adhikari, Sarina [ORNL] [ORNL; Rizy, D Tom [ORNL] [ORNL; Li, Fangxing [ORNL] [ORNL; Irminger, Philip [ORNL] [ORNL

    2012-01-01T23:59:59.000Z

    Grid-connected photovoltaic (PV) systems with power electronic interfaces can provide both real and reactive power to meet power system needs with appropriate control algorithms. This paper presents the control algorithm design for a three-phase single-stage grid-connected PV inverter to achieve either maximum power point tracking (MPPT) or a certain amount of real power injection, as well as the voltage/var control. The switching between MPPT control mode and a certain amount of real power control mode is automatic and seamless. Without the DC-to-DC booster stage, PV DC voltage stability is an important issue in the control design especially when the PV inverter is operating at maximum power point (MPP) with voltage/var control. The PV DC voltage collapse phenomenon and its reason are discussed. The method based on dynamic correction of the PV inverter output is proposed to ensure PV DC voltage stability. Simulation results of the single-stage PV system during system disturbances and fast solar irradiation changes confirm that the proposed control algorithm for single-stage PV inverters can provide appropriate real and reactive power services and ensure PV DC voltage stability during dynamic system operation and atmospheric conditions.

  9. TO: THE QER SECRETARIAT FROM: THE ENTERGY OPERATING COMPANIES

    Broader source: Energy.gov (indexed) [DOE]

    type of investment is needed in energy TS&D to ensure the safe delivery of electricity, natural gas, oil and liquid fuels, given the average age of the systems? A.8 Investment...

  10. Nitrogen stabilized reactive sputtering of optimized TiO{sub 2-x} photocatalysts with visible light reactivity

    SciTech Connect (OSTI)

    Chen, Le; Graham, Michael E.; Gray, Kimberly A. [Department of Civil and Environmental Engineering, Northwestern University, Evanston, Illinois 60208 (United States); Department of Materials Science and Engineering, Northwestern University, Evanston, Illinois 60208 (United States); Department of Civil and Environmental Engineering, Northwestern University, Evanston, Illinois 60208 (United States)

    2009-07-15T23:59:59.000Z

    Photoreactive and visible light responsive nonstoichiometric mixed-phase titania was prepared by reactive direct current magnetron sputtering. Trace amounts of nitrogen were added for process stabilization without being incorporated into the films. Based on the CO{sub 2} photoreduction tests and structural and optical characterization, the influence of the trace nitrogen on the sputtered nonstoichiometric TiO{sub 2} was studied and was compared to nitrogen-doped titania.

  11. HQ- Human Resources Operations

    Broader source: Energy.gov [DOE]

    HQs Human Recources Operations delivers services, including position management, recruitment, staffing and classification, and reduction in force at Headquarters.  Click the "Contacts" Link to find...

  12. Hyponormality of Toeplitz Operators

    E-Print Network [OSTI]

    1910-40-52T23:59:59.000Z

    Amer. Math. Soc. 82(1976), 494-496. [12] S. C. Power. Hankel Operators on Hilbert Space, Pitman, Boston, 1982. [13] D. Sarason. Generalized interpolation in H.

  13. Spectral Operators of Matrices

    E-Print Network [OSTI]

    2014-01-10T23:59:59.000Z

    Jan 10, 2014 ... a thorough study on a new class of matrix valued functions, coined as spectral operators of ..... not self-adjoint. ...... 9 (1981) 1135–1151.

  14. Pipeline Operations Program (Louisiana)

    Broader source: Energy.gov [DOE]

    The Pipeline Operations Program regulates the construction, acquisition, abandonment and interconnection of natural gas pipelines, as well as, the transportation and use of natural gas supplies.

  15. Load-follow operation with the MSHIM control system

    SciTech Connect (OSTI)

    Morita, T.; Carlsen, B.W.; Kutz, J.P.

    1988-01-01T23:59:59.000Z

    As part of Westinghouse Electric Corporation's ongoing efforts to improve plant daily load-follow capability, a system has been developed that promises a significant enhancement of current load-maneuvering capabilities, while simultaneously reducing the burden on operators and plant systems. This concept, the mechanical shim (MSHIM), control system utilizes two independently operable groups of control banks for essentially simultaneous control of reactivity and axial power distribution. This system has been developed with the goal of supporting either of two operational modes. One mode is designed to maximize spinning reserve (MAXSR) capacity (return to full-power capability). The other mode minimizes boric (MINB) acid changes, hence effluent production, during the power maneuver. The features of the two control modes are summarized.

  16. Ordered involutive operator spaces

    E-Print Network [OSTI]

    Blecher, David P; Neal, Matthew; Werner, Wend

    2007-01-01T23:59:59.000Z

    This is a companion to recent papers of the authors; here we construct the `noncommutative Shilov boundary' of a (possibly nonunital) selfadjoint ordered space of Hilbert space operators. The morphisms in the universal property of the boundary preserve order. As an application, we consider `maximal' and `minimal' unitizations of such ordered operator spaces.

  17. Operations Research + Information Engineering

    E-Print Network [OSTI]

    Keinan, Alon

    and the equipment they operate to perform most efficiently. The allocation of resources may be represented of the techniques and modeling concepts needed to analyze and design complex systems. As an operations researcher. All business systems are complex and need sophisticated decision-making methods that enable employees

  18. Humanitarian Operations Pinar Keskinocak

    E-Print Network [OSTI]

    Li, Mo

    1 Humanitarian Operations Pinar Keskinocak H. Milton Stewart School of Industrial & Systems for Allocating Urban Emergency Units: A Survey Larson (1972), Urban Police Patrol Analysis Larson and Odoni (1981), Urban Operations Research Jones and Eden (1981), O.R. in the Community Pollock, Rothkopf, Barnett (1994

  19. Survey of Reactive Power Planning Methods Wenjuan Zhang, Student Member, IEEE, Leon M. Tolbert, Senior Member, IEEE

    E-Print Network [OSTI]

    Tolbert, Leon M.

    Survey of Reactive Power Planning Methods Wenjuan Zhang, Student Member, IEEE, Leon M. Tolbert, Senior Member, IEEE Abstract Reactive power planning (RPP) involves optimal allocation and determination to solve the RPP problem. Index Terms -- reactive power planning, reactive power optimization, optimal

  20. Transportation of a 40-year-old reactive mixed waste

    SciTech Connect (OSTI)

    Dietz, C.G. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

    1996-12-31T23:59:59.000Z

    Now a national landmark, Experimental Breeder Reactor-I was the worlds first nuclear reactor to produce a usable amount of commercial electricity in 1951. It is located on the Arco desert in Eastern Idaho at the Idaho National Engineering Laboratory (INEL). In 1955, the reactor experienced a cooling accident that resulted in core damage and a partial meltdown of the reactor, which left a serious cleanup challenge that had not been addressed until recently. The EBR-I reactor used liquid metal sodium-potassium (NaK) as a coolant because it is eutectic; that is, it remains a liquid at the lowest possible temperature and was a very effective coolant. NaK looks very much like mercury out of a thermometer. However, NaK is reactive and will burn in the presence of air (absorbing moisture from it) and is extremely reactive in direct contact with water, producing hydrogen. Furthermore, this highly reactive coolant was radioactively contaminated from the accident. Most of the radioactively contaminated NaK was processed and disposed of in 1955. However, approximately 180 gal of residual contaminated NaK remained because of the possibility it contained 10 1-gram foils of plutonium, which were in the reactor core at the time of the meltdown. This NaK was stored in four containers: two 55-gallon stainless steel transportation drums, one 60-gallon carbon steel container (used as a transfer vessel), and one 10-gallon carbon steel container (used to store radioactively contaminated water). This paper describes the transport of this waste from its temporary storage bunker to Argonne National Laboratory West for final treatment and preparation for disposal.

  1. Gas sampling system for reactive gas-solid mixtures

    DOE Patents [OSTI]

    Daum, Edward D. (Alliance, OH); Downs, William (Alliance, OH); Jankura, Bryan J. (Mogadore, OH); McCoury, Jr., John M. (Mineral City, OH)

    1990-01-01T23:59:59.000Z

    An apparatus and method for sampling gas containing a reactive particulate solid phase flowing through a duct and for communicating a representative sample to a gas analyzer. A sample probe sheath 32 with an angular opening 34 extends vertically into a sample gas duct 30. The angular opening 34 is opposite the gas flow. A gas sampling probe 36 concentrically located within sheath 32 along with calibration probe 40 partly extends in the sheath 32. Calibration probe 40 extends further in the sheath 32 than gas sampling probe 36 for purging the probe sheath area with a calibration gas during calibration.

  2. Gas sampling system for reactive gas-solid mixtures

    DOE Patents [OSTI]

    Daum, Edward D. (Alliance, OH); Downs, William (Alliance, OH); Jankura, Bryan J. (Mogadore, OH); McCoury, Jr., John M. (Mineral City, OH)

    1989-01-01T23:59:59.000Z

    An apparatus and method for sampling a gas containing a reactive particulate solid phase flowing through a duct and for communicating a representative sample to a gas analyzer. A sample probe sheath 32 with an angular opening 34 extends vertically into a sample gas duct 30. The angular opening 34 is opposite the gas flow. A gas sampling probe 36 concentrically located within sheath 32 along with calibration probe 40 partly extend in the sheath 32. Calibration probe 40 extends further in the sheath 32 than gas sampling probe 36 for purging the probe sheath area with a calibration gas during calibration.

  3. Method for preparing hydride configurations and reactive metal surfaces

    DOE Patents [OSTI]

    Silver, Gary L. (Centerville, OH)

    1988-08-16T23:59:59.000Z

    A method for preparing highly hydrogen-reactive surfaces on metals which normally require substantial heating, high pressures, or an extended induction period, which involves pretreatment of said surfaces with either a non-oxidizing acid or hydrogen gas to form a hydrogen-bearing coating on said surfaces, and subsequently heating said coated metal in the absence of moisture and oxygen for a period sufficient to decompose said coating and cooling said metal to room temperature. Surfaces so treated will react almost instantaneously with hydrogen gas at room temperature and low pressure. The method is particularly applicable to uranium, thorium, and lanthanide metals.

  4. Reactive sticking coefficients for silane and disilane on polycrystalline silicon

    SciTech Connect (OSTI)

    Buss, R.J.; Ho, P.; Breiland, W.G.; Coltrin, M.E.

    1988-04-15T23:59:59.000Z

    Reactive sticking coefficients (RSCs) were measured for silane and disilane on polycrystalline silicon for a wide range of temperature and flux (pressure) conditions. The data were obtained from deposition-rate measurements using molecular beam scattering and a very low-pressure cold-wall reactor. The RSCs have nonlinear Arrhenius temperature dependencies and decrease with increasing flux at low (710 /sup 0/C) temperatures. Several simple models are proposed to explain these observations. The results are compared with previous studies of the SiH/sub 4//Si(s) reaction and low-pressure chemical vapor deposition-rate measurements.

  5. Low Reactivity SI Engine Lubricant Program | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetterEconomy andTerms LoanLos AngelesGuillermo10Reactivity SI

  6. DOE - Office of Legacy Management -- Reactive Metals Inc - OH 10

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp -K Le Blond Machine Tool Co -Reactive

  7. Quantum Operation Time Reversal

    SciTech Connect (OSTI)

    Crooks, Gavin E.

    2008-03-25T23:59:59.000Z

    The dynamics of an open quantum system can be described by a quantum operation: A linear, complete positive map of operators. Here, I exhibit a compact expression for the time reversal of a quantum operation, which is closely analogous to the time reversal of a classical Markov transition matrix. Since open quantum dynamics are stochastic, and not, in general, deterministic, the time reversal is not, in general, an inversion of the dynamics. Rather, the system relaxes toward equilibrium in both the forward and reverse time directions. The probability of a quantum trajectory and the conjugate, time reversed trajectory are related by the heat exchanged with the environment.

  8. Operation Prognostics and Operation Diagnostics—Technologies for Enhanced Operations and Controls

    E-Print Network [OSTI]

    Baumann, O.

    PROGNOSTICS AND OPERATION DIAGNOSTICS ? NEW TECHNOLOGIES FOR ENHANCED OPERATIONS AND CONTROLS OLIVER BAUMANN, PRESIDENT 202-608-1334 EBERT & BAUMANN CONSULTING ENGINEERS, WASHINGTON D.C. The Methodologies of Operation Prognostics and Operation...

  9. Conduct of Operations

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2010-06-29T23:59:59.000Z

    This Order defines the requirements for establishing and implementing Conduct of Operations Programs at Department of Energy (DOE), including National Nuclear Security Administration (NNSA), facilities and projects. Cancels DOE O 5480.19. Admin Chg 1, 6-25-13

  10. Operation Research Analyst

    Broader source: Energy.gov [DOE]

    The incumbent in this position will serve as an Operation Research Analyst in the Market Analysis and Pricing organization of Power Services. This organization is responsible for performing market...

  11. Operations Security Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1992-04-30T23:59:59.000Z

    To establish policies, responsibilities and authorities for implementing and sustaining the Department of Energy (DOE) Operations Security (OPSEC) Program. Cancels DOE O 5632.3B. Canceled by DOE O 471.2 of 9-28-1995.

  12. Nuclear material operations manual

    SciTech Connect (OSTI)

    Tyler, R.P.

    1981-02-01T23:59:59.000Z

    This manual provides a concise and comprehensive documentation of the operating procedures currently practiced at Sandia National Laboratories with regard to the management, control, and accountability of nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations-management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of playscripts in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion.

  13. Protection Program Operations

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2014-10-14T23:59:59.000Z

    This Order establishes requirements for the management and operation of the Department of Energy (DOE) Federal Protective Forces (FPF), Contractor Protective Forces (CPF), and the Physical Security of property and personnel under the cognizance of DOE.

  14. Continuity of Operations

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2005-01-14T23:59:59.000Z

    The notice defines requirements and responsibilities for continuity of operations planning within the DOE to ensure the capability to continue essential Departmental functions across a wide range of all hazard emergencies. Does not cancel other directives.

  15. Operations | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Operations Argonne mentors students for the next generation of scientistsMay 28, 2015 On May 6, the accomplishments of seventeen Chicago-area high school students that had been...

  16. Richland Operations Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Department of Energy Richland Operations Office P.O. Box 550 &?ATES0Richland, Washington 99352 10O-AMSE-0054 A PR I Mr. J. G. Lehew III, President and Chief Executive Officer...

  17. SNS Target Systems Operational

    E-Print Network [OSTI]

    McDonald, Kirk

    a failed gas seal on the shaft and leaking oil seals but has operated well since then · The moderator 7.5 k First target replacement · No observed corrosion · Internal Boroscope examination in progress · ~ 50 mm

  18. Operational Waste Volume Projection

    SciTech Connect (OSTI)

    STRODE, J.N.

    1999-08-24T23:59:59.000Z

    Waste receipts to the double-shell tank system are analyzed and wastes through the year 2018 are projected based on assumption as of July 1999. A computer simulation of site operations is performed, which results in projections of tank fill schedules, tank transfers, evaporator operations, tank retrieval, and aging waste tank usage. This projection incorporates current budget planning and the clean-up schedule of the Tri-Party Agreement.

  19. Operational Waste Volume Projection

    SciTech Connect (OSTI)

    STRODE, J.N.

    2000-08-28T23:59:59.000Z

    Waste receipts to the double-shell tank system are analyzed and wastes through the year 2015 are projected based on generation trends of the past 12 months. A computer simulation of site operations is performed, which results in projections of tank fill schedules, tank transfers, evaporator operations, tank retrieval, and aging waste tank usage. This projection incorporates current budget planning and the clean-up schedule of the Tri-Party Agreement. Assumptions were current as of June. 2000.

  20. Operational waste volume projection

    SciTech Connect (OSTI)

    Koreski, G.M.

    1996-09-20T23:59:59.000Z

    Waste receipts to the double-shell tank system are analyzed and wastes through the year 2015 are projected based on generation trends of the past 12 months. A computer simulation of site operations is performed, which results in projections of tank fill schedules, tank transfers, evaporator operations, tank retrieval, and aging waste tank usage. This projection incorporates current budget planning and the clean-up schedule of the Tri-Party Agreement. Assumptions were current as of June 1996.

  1. Application of simultaneous active and reactive power modulation of superconducting magnetic energy storage unit to damp turbine-generator subsynchronous oscillations

    SciTech Connect (OSTI)

    Wu, Chijui; Lee, Yuangshung (National Taiwan Inst. of Tech., Taipie (Taiwan, Province of China))

    1993-03-01T23:59:59.000Z

    An active and reactive power (P-Q) simultaneous control scheme which is based on a superconducting magnetic energy storage (SMES) unit is designed to damp out the subsynchronous resonant (SSR) oscillations of a turbine-generator unit. In order to suppress unstable torsional mode oscillations, a proportional-integral-derivative (PID) controller is employed to modulate the active and reactive power input/output of the SMES unit according to speed deviation of the generator shaft. The gains of the proposed PID controller are determined by pole assignment approach based on modal control theory. Eigenvalue analysis of the studied system shows that the PID controller is quite effective over a wide range of operating conditions. Dynamic simulations using the nonlinear system model are also performed to demonstrate the damping effect of the proposed control scheme under disturbance conditions.

  2. Hybrid nuclear reactor grey rod to obtain required reactivity worth

    DOE Patents [OSTI]

    Miller, John V. (Munhall, PA); Carlson, William R. (Scott Township, Allegheny County, PA); Yarbrough, Michael B. (Hempfield Township, Westmoreland County, PA)

    1991-01-01T23:59:59.000Z

    Hybrid nuclear reactor grey rods are described, wherein geometric combinations of relatively weak neutron absorber materials such as stainless steel, zirconium or INCONEL, and relatively strong neutron absorber materials, such as hafnium, silver-indium cadmium and boron carbide, are used to obtain the reactivity worths required to reach zero boron change load follow. One embodiment includes a grey rod which has combinations of weak and strong neutron absorber pellets in a stainless steel cladding. The respective pellets can be of differing heights. A second embodiment includes a grey rod with a relatively thick stainless steel cladding receiving relatively strong neutron absorber pellets only. A third embodiment includes annular relatively weak netron absorber pellets with a smaller diameter pellet of relatively strong absorber material contained within the aperture of each relatively weak absorber pellet. The fourth embodiment includes pellets made of a homogeneous alloy of hafnium and a relatively weak absorber material, with the percentage of hafnium chosen to obtain the desired reactivity worth.

  3. Reactive-coupling-induced normal mode splittings in microdisk resonators coupled to waveguides

    SciTech Connect (OSTI)

    Huang Sumei; Agarwal, G. S. [Department of Physics, Oklahoma State University, Stillwater, Oklahoma 74078 (United States)

    2010-05-15T23:59:59.000Z

    We study the optomechanical design introduced by M. Li et al. [Phys. Rev. Lett. 103, 223901 (2009)], which is very effective for investigation of the effects of reactive coupling. We show the normal mode splitting that is due solely to reactive coupling rather than due to dispersive coupling. We suggest feeding the waveguide with a pump field along with a probe field and scanning the output probe for evidence of reactive-coupling-induced normal mode splitting.

  4. Rat colonic reactive oxygen species production and DNA damage are mediated by diet and age

    E-Print Network [OSTI]

    Henderson, Cara Aletha Everett

    2001-01-01T23:59:59.000Z

    diacetate docosahexanoic acid diphenyliodonium chloride ethylenediaminetetraacetic acid eicosapentanoic acid ethidium homodiner ? 1 fragment length analysis using repair enzymes Fapy glycosylase Hanks' balanced salt solution hydrogen peroxide lipid... the elimination of cancer cells. Production and Functions of Reactive Oxygen Species Formation of reactive oxygen species Reactive oxygen species are a by-product of normal metabolism and include superoxide (Ot' ), hydrogen peroxide (HzO&), and the hydroxyl...

  5. Composite Materials for Hazard Mitigation of Reactive Metal Hydrides.

    SciTech Connect (OSTI)

    Pratt, Joseph William; Cordaro, Joseph Gabriel; Sartor, George B.; Dedrick, Daniel E.; Reeder, Craig L.

    2012-02-01T23:59:59.000Z

    In an attempt to mitigate the hazards associated with storing large quantities of reactive metal hydrides, polymer composite materials were synthesized and tested under simulated usage and accident conditions. The composites were made by polymerizing vinyl monomers using free-radical polymerization chemistry, in the presence of the metal hydride. Composites with vinyl-containing siloxane oligomers were also polymerized with and without added styrene and divinyl benzene. Hydrogen capacity measurements revealed that addition of the polymer to the metal hydride reduced the inherent hydrogen storage capacity of the material. The composites were found to be initially effective at reducing the amount of heat released during oxidation. However, upon cycling the composites, the mitigating behavior was lost. While the polymer composites we investigated have mitigating potential and are physically robust, they undergo a chemical change upon cycling that makes them subsequently ineffective at mitigating heat release upon oxidation of the metal hydride. Acknowledgements The authors would like to thank the following people who participated in this project: Ned Stetson (U.S. Department of Energy) for sponsorship and support of the project. Ken Stewart (Sandia) for building the flow-through calorimeter and cycling test stations. Isidro Ruvalcaba, Jr. (Sandia) for qualitative experiments on the interaction of sodium alanate with water. Terry Johnson (Sandia) for sharing his expertise and knowledge of metal hydrides, and sodium alanate in particular. Marcina Moreno (Sandia) for programmatic assistance. John Khalil (United Technologies Research Corp) for insight into the hazards of reactive metal hydrides and real-world accident scenario experiments. Summary In an attempt to mitigate and/or manage hazards associated with storing bulk quantities of reactive metal hydrides, polymer composite materials (a mixture of a mitigating polymer and a metal hydride) were synthesized and tested under simulated usage and accident conditions. Mitigating the hazards associated with reactive metal hydrides during an accident while finding a way to keep the original capability of the active material intact during normal use has been the focus of this work. These composites were made by polymerizing vinyl monomers using free-radical polymerization chemistry, in the presence of the metal hydride, in this case a prepared sodium alanate (chosen as a representative reactive metal hydride). It was found that the polymerization of styrene and divinyl benzene could be initiated using AIBN in toluene at 70 degC. The resulting composite materials can be either hard or brittle solids depending on the cross-linking density. Thermal decomposition of these styrene-based composite materials is lower than neat polystyrene indicating that the chemical nature of the polymer is affected by the formation of the composite. The char-forming nature of cross-linked polystyrene is low and therefore, not an ideal polymer for hazard mitigation. To obtain composite materials containing a polymer with higher char-forming potential, siloxane-based monomers were investigated. Four vinyl-containing siloxane oligomers were polymerized with and without added styrene and divinyl benzene. Like the styrene materials, these composite materials exhibited thermal decomposition behavior significantly different than the neat polymers. Specifically, the thermal decomposition temperature was shifted approximately 100 degC lower than the neat polymer signifying a major chemical change to the polymer network. Thermal analysis of the cycled samples was performed on the siloxane-based composite materials. It was found that after 30 cycles the siloxane-containing polymer composite material has similar TGA/DSC-MS traces as the virgin composite material indicating that the polymer is physically intact upon cycling. Hydrogen capacity measurements revealed that addition of the polymer to the metal hydride in the form of a composite material reduced the inherent hydrogen storage capacity of the material. This

  6. Corrosion-induced gas generation in a nuclear waste repository: Reactive geochemistry and multiphase flow effect

    E-Print Network [OSTI]

    Xu, T.

    2009-01-01T23:59:59.000Z

    Lying Repositories for Nuclear Waste, NAGRA Technical Reporthost rock formation for nuclear waste storage. EngineeringGas Generation in a Nuclear Waste Repository: Reactive

  7. Atomic-level studies of the depletion in reactive sites during...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    weathering, the atomic-level “reactive sites” on the surfaces of minerals must be characterized and quantified. Whether these sites are atomic in nature,...

  8. Effect of different intravenous iron preparations on lymphocyte intracellular reactive oxygen species generation and subpopulation survival.

    E-Print Network [OSTI]

    Gupta, Ajay; Zhuo, Jiaying; Zha, Junli; Reddy, Srinivasa; Olp, Jonathan; Pai, Amy

    2010-01-01T23:59:59.000Z

    IV iron compounds induced greater intracellular ROS generation,IV iron preparations on intracellular reactive oxygen species generationIV iron preparations on intracellular immune cell ROS generation

  9. Influence of Mg2+ on CaCO3 precipitation during subsurface reactive...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    subsurface reactive transport in a homogeneous silicon-etched pore network. Abstract: Calcium carbonate (CaCO3) geochemical reactions exert a fundamental control on the...

  10. Reactive Distillation for Esterification of Bio-based Organic...

    Office of Scientific and Technical Information (OSTI)

    column replaced thirteen individual unit operations and now meets the company's entire demand for methyl acetate. Although representative of the kind of success possible with...

  11. Reactive Power Management using Firefly and Spiral Optimization ...

    E-Print Network [OSTI]

    -

    2013-09-08T23:59:59.000Z

    being generator bus voltage, capacitor shunts and transformer taps. ... Under stable running conditions the devices are operational at rated values and have ...

  12. Zero-Valent Iron Permeable Reactive Barriers: A Review of Performance

    SciTech Connect (OSTI)

    Korte, NE

    2001-06-11T23:59:59.000Z

    This report briefly reviews issues regarding the implementation of the zero-valent iron permeable reactive barrier (PRB) technology at sites managed by the U.S. Department of Energy (DOE). Initially, the PRB technology, using zero-valent iron for the reactive media, was received with great enthusiasm, and DOE invested millions of dollars testing and implementing PRBs. Recently, a negative perception of the technology has been building. This perception is based on the failure of some deployments to satisfy goals for treatment and operating expenses. The purpose of this report, therefore, is to suggest reasons for the problems that have been encountered and to recommend whether DOE should invest in additional research and deployments. The principal conclusion of this review is that the most significant problems have been the result of insufficient characterization, which resulted in poor engineering implementation. Although there are legitimate concerns regarding the longevity of the reactive media, the ability of zero-valent iron to reduce certain chlorinated hydrocarbons and to immobilize certain metals and radionuclides is well documented. The primary problem encountered at some DOE full-scale deployments has been an inadequate assessment of site hydrology, which resulted in misapplication of the technology. The result is PRBs with higher than expected flow velocities and/or incomplete plume capture. A review of the literature reveals that cautions regarding subsurface heterogeneity were published several years prior to the full-scale implementations. Nevertheless, design and construction have typically been undertaken as if the subsurface was homogeneous. More recently published literature has demonstrated that hydraulic heterogeneity can cause so much uncertainty in performance that use of a passive PRB is precluded. Thus, the primary conclusion of this review is that more attention must be given to site-specific issues. Indeed, the use of a passive PRB requires an unusually comprehensive hydrologic characterization so that the design can be based on a thorough understanding of subsurface heterogeneity rather than on average values for hydraulic parameters. Scientists and engineers are capable of conducting the level of investigation required. However, design costs will increase, and the pre-design field work may demonstrate that a passive PRB is not suitable for a particular site. In such cases, an option to consider is hydraulic augmentation, such as pumping (in which the system is no longer passive) or gravity flow from drains. In these circumstances, operation of the treatment media is under known hydraulic conditions. These systems typically contain the treatment media in a vault or in drums. Most of the media problems in such systems have been related to the exclusion of air and can be addressed by better engineering design or by frequent maintenance. Finally, a number of outstanding issues require resolution for further application of this technology. Of particular interest to DOE is resolving the removal mechanisms for uranium and technetium. Few data are available for the latter, and for the former, the technical literature is contradictory. Determining the mechanisms has long-term cost implications; engineers must consider whether it is appropriate to remove or simply abandon a barrier that is no longer functioning. Other issues that are unresolved include determining how hydraulic performance is affected by the emplacement method and quantifying the effects of varying groundwater types on barrier longevity.

  13. Investigating the potential for long-term permeable reactive barrier (PRB) monitoring from the electrical signatures associated with the reduction in reactive iron performance

    SciTech Connect (OSTI)

    Slater, Lee D.; Korte, N.; Baker, J.

    2005-12-14T23:59:59.000Z

    The objective of this work was to conduct laboratory and field experiments to determine the sensitivity of low frequency electrical measurements (resistivity and induced polarization) to the processes of corrosion and precipitation that are believed to limit permeable reactive barrier (PRB) performance. The research was divided into four sets of experiments that were each written up and submitted to a peer-reviewed journal: [1] A laboratory experiment to define the controls of aqueous chemistry (electrolyte activity; pH; valence) and total zero valent iron (Fe0) available surface area on the electrical properties of Fe0 columns. [2] A laboratory experiment to determine the impact of corrosion and precipitation on the electrical response of synthetic Fe0 columns as a result of geochemical reactions with NaSO4 and NaCO3 electrolytes. [3] Laboratory experiments on a sequence of cores retrieved from the Kansas City PRB to determine the magnitude of electrical and geochemical changes within a field active PRB after eight years of operation [4] Field-scale cross borehole resistivity and induced polarization monitoring of the Kansas City PRB to evaluate the potential of electrical imaging as a technology for non-invasive, long-term monitoring of indicators of reduced PRB performance This report first summarizes the findings of the four major experiments conducted under this research. The reader is referred to the four papers in Appendices 1-4 for a full description of each experiment, including motivation and significance, technical details, findings and implications. The deliverables of the project, including the publications, conference papers and new collaborative arrangements that have resulted are then described. Appendices 5-6 contain two technical reports written by co-PI Korte describing (1) supporting geochemical measurements, and (2) the coring procedure, conducted at the Kansas City PRB as part of this project.

  14. A Reactive Control Approach for Pipeline Inspection with an AUV

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    robots, or UUVs (unmanned underwater vehicles) have long been present per- forming commercial operations operations suggest that autonomous underwater vehicles will become increasingly present in com- mercial autonomous underwater vehicle. The method presented here, called the Deformable Virtual Zones (DVZ) method

  15. Reactive-power compensation of coal mining excavators by using a new-generation STATCOM

    SciTech Connect (OSTI)

    Bilgin, H.F.; Ermis, M.; Kose, K.N.; Cadirci, I.; Acik, A.; Demirci, T.; Terciyanli, A.; Kocak, C.; Yorukoglu, M. [TUBITAK Information Technology & Electronic Research Institute, Ankara (Turkey)

    2007-01-15T23:59:59.000Z

    This paper deals with the development and implementation of a current-source-converter-based static synchronous compensator (CSC-STATCOM) applied to the volt-ampere-reactive (VAR) compensation problem of coal mining excavators. It is composed of a +/- 750-kVAR full-bridge CSC with selective harmonic elimination, a low-pass input filter tuned to 200 Hz, and a Delta/Y-connected coupling transformer for connection to medium-voltage load bus. Each power semiconductor switch is composed of an asymmetrical integrated gate commutated thyristor (IGCT) connected in series with a reverse-blocking diode and switched at 500 Hz to eliminate 5th, 7th, 11th, and 13th current harmonics produced by the CSC. Operating principles, power stage, design of dc link, and input filter are also described in this paper. It has been verified by field tests that the developed STATCOM follows rapid fluctuations in nearly symmetrical lagging and leading VAR consumption of electric excavators, resulting in nearly unity power factor on monthly basis, and the harmonic current spectra in the lines of CSC-STATCOM at the point of common coupling comply with the IEEE Standard 519-1992.

  16. Mineral Precipitation Upgradient from a Zero-Valent Iron Permeable Reactive Barrier

    SciTech Connect (OSTI)

    Johnson, R. L.; Thoms, R. B.; Johnson, R. O.; Nurmi, J. T.; Tratnyek, Paul G.

    2008-07-01T23:59:59.000Z

    Core samples taken from a zero-valent iron permeable reactive barrier (ZVI PRB) at Cornhusker Army Ammunition Plant, Nebraska, were analyzed for physical and chemical characteristics. Precipitates containing iron and sulfide were present at much higher concentrations in native aquifer materials just upgradient of the PRB than in the PRB itself. Sulfur mass balance on core solids coupled with trends in ground water sulfate concentrations indicates that the average ground water flow after 20 months of PRB operation was approximately twenty fold less than the regional ground water velocity. Transport and reaction modeling of the aquifer PRB interface suggests that, at the calculated velocity, both iron and hydrogen could diffuse upgradient against ground water flow and thereby contribute to precipitation in the native aquifer materials. The initial hydraulic conductivity (K) of the native materials is less than that of the PRB and, given the observed precipitation in the upgradient native materials, it is likely that K reduction occurred upgradient to rather than within the PRB. Although not directly implicated, guar gum used during installation of the PRB is believed to have played a role in the precipitation and flow reduction processes by enhancing microbial activity.

  17. Accelerating moderately stiff chemical kinetics in reactive-flow simulations using GPUs

    E-Print Network [OSTI]

    Niemeyer, Kyle E

    2014-01-01T23:59:59.000Z

    The chemical kinetics ODEs arising from operator-split reactive-flow simulations were solved on GPUs using explicit integration algorithms. Nonstiff chemical kinetics of a hydrogen oxidation mechanism (9 species and 38 irreversible reactions) were computed using the explicit fifth-order Runge-Kutta-Cash-Karp method, and the GPU-accelerated version performed faster than single- and six-core CPU versions by factors of 126 and 25, respectively, for 524,288 ODEs. Moderately stiff kinetics, represented with mechanisms for hydrogen/carbon-monoxide (13 species and 54 irreversible reactions) and methane (53 species and 634 irreversible reactions) oxidation, were computed using the stabilized explicit second-order Runge-Kutta-Chebyshev (RKC) algorithm. The GPU-based RKC implementation demonstrated an increase in performance of nearly 59 and 10 times, for problem sizes consisting of 262,144 ODEs and larger, than the single- and six-core CPU-based RKC algorithms using the hydrogen/carbon-monoxide mechanism. With the met...

  18. SSCL Commissioning and Operations

    SciTech Connect (OSTI)

    NONE

    1992-03-31T23:59:59.000Z

    The SSC, with an energy of 20 TeV/Beam, requires a sequence of individual accelerators of increasing energy in the injector chain. These are the Linac, Low Energy Booster, Medium Energy Booster, and High Energy Booster. Each accelerator system must be completed in sequence in order to provide beam to the next higher energy accelerator. The collider itself is comprised of ten sectors, each of which in terms of superconducting magnet bending strength, is equivalent to two HEB injectors. The completion of all injectors and collider sectors is required before stored beams can circulate in preparation for colliding beam operation. Four experimental halls are planned for the detector systems. Each major detector will be assembled in one of the halls by a world-wide collaboration of scientists. In addition, above ground facilities provide shops and test facilities for accelerator technical systems, superconducting magnet and materials research and development, and for detector assembly and operations. The purpose of this report is to present a plan for the sequential commissioning and operation of these individual accelerators and other technical facilities of the SSC. A central objective of this plan is to describe the activities at the SSCL that are not included as part of the construction project TPC, even though they occur during the overall project construction time-frame. Examples of such activities include the operation of general laboratory facilities and services not specifically related to construction, the operating costs for the individual accelerators in the injector chain once these facilities have been commissioned, and the costs of SSCL physics research groups. The Department of Energy has provided the following decision with regard to these operations categories for the SSCL.

  19. Anode reactive bleed and injector shift control strategy

    DOE Patents [OSTI]

    Cai, Jun [Rochester, NY; Chowdhury, Akbar [Pittsford, NY; Lerner, Seth E [Honeoye Falls, NY; Marley, William S [Rush, NY; Savage, David R [Rochester, NY; Leary, James K [Rochester, NY

    2012-01-03T23:59:59.000Z

    A system and method for correcting a large fuel cell voltage spread for a split sub-stack fuel cell system. The system includes a hydrogen source that provides hydrogen to each split sub-stack and bleed valves for bleeding the anode side of the sub-stacks. The system also includes a voltage measuring device for measuring the voltage of each cell in the split sub-stacks. The system provides two levels for correcting a large stack voltage spread problem. The first level includes sending fresh hydrogen to the weak sub-stack well before a normal reactive bleed would occur, and the second level includes sending fresh hydrogen to the weak sub-stack and opening the bleed valve of the other sub-stack when the cell voltage spread is close to stack failure.

  20. Distributed control for optimal reactive power compensation in smart microgrids

    E-Print Network [OSTI]

    Bolognani, Saverio

    2011-01-01T23:59:59.000Z

    We consider the problem of optimal reactive power compensation for the minimization of power distribution losses in a smart microgrid. We first propose an approximate model for the power distribution network, which allows us to cast the problem into the class of convex quadratic, linearly constrained, optimization problems. We also show how this model provides the tools for a distributed approach, in which agents have a partial knowledge of the problem parameters and state, and can only perform local measurements. Then, we design a randomized, gossip-like optimization algorithm, providing conditions for convergence together with an analytic characterization of the convergence speed. The analysis shows that the best performance can be achieved when we command cooperation among agents that are neighbors in the smart microgrid topology. Numerical simulations are included to validate the proposed model and to confirm the analytic results about the performance of the proposed algorithm.

  1. Advanced hydraulic fracturing methods to create in situ reactive barriers

    SciTech Connect (OSTI)

    Murdoch, L. [FRX Inc., Cincinnati, OH (United States)]|[Clemson Univ., SC (United States). Dept. of Geological Sciences; Siegrist, B.; Meiggs, T. [Oak Ridge National Lab., TN (United States)] [and others

    1997-12-31T23:59:59.000Z

    This article describes the use of hydraulic fracturing to increase permeability in geologic formations where in-situ remedial action of contaminant plumes will be performed. Several in-situ treatment strategies are discussed including the use of hydraulic fracturing to create in situ redox zones for treatment of organics and inorganics. Hydraulic fracturing methods offer a mechanism for the in-situ treatment of gently dipping layers of reactive compounds. Specialized methods using real-time monitoring and a high-energy jet during fracturing allow the form of the fracture to be influenced, such as creation of assymmetric fractures beneath potential sources (i.e. tanks, pits, buildings) that should not be penetrated by boring. Some examples of field applications of this technique such as creating fractures filled with zero-valent iron to reductively dechlorinate halogenated hydrocarbons, and the use of granular activated carbon to adsorb compounds are discussed.

  2. Method of measuring reactive acoustic power density in a fluid

    DOE Patents [OSTI]

    Wheatley, J.C.; Swift, G.W.; Migliori, A.

    1985-09-03T23:59:59.000Z

    A method for determining reactive acoustic power density level and its direction in a fluid using a single sensor is disclosed. In the preferred embodiment, an apparatus for conducting the method, which is termed a thermoacoustic couple, consists of a stack of thin, spaced apart polymeric plates, selected ones of which include multiple bimetallic thermocouple junctions positioned along opposite end edges thereof. The thermocouple junctions are connected in series in the nature of a thermopile, and are arranged so as to be responsive to small temperature differences between the opposite edges of the plates. The magnitude of the temperature difference, as represented by the magnitude of the electrical potential difference generated by the thermopile, is found to be directly related to the level of acoustic power density in the gas. 5 figs.

  3. Method of measuring reactive acoustic power density in a fluid

    DOE Patents [OSTI]

    Wheatley, John C. (Los Alamos, NM); Swift, Gregory W. (Los Alamos, NM); Migliori, Albert (Santa Fe, NM)

    1985-01-01T23:59:59.000Z

    A method for determining reactive acoustic power density level and its direction in a fluid using a single sensor is disclosed. In the preferred embodiment, an apparatus for conducting the method, which is termed a thermoacoustic couple, consists of a stack of thin, spaced apart polymeric plates, selected ones of which include multiple bimetallic thermocouple junctions positioned along opposite end edges thereof. The thermocouple junctions are connected in series in the nature of a thermopile, and are arranged so as to be responsive to small temperature differences between the opposite edges of the plates. The magnitude of the temperature difference, as represented by the magnitude of the electrical potential difference generated by the thermopile, is found to be directly related to the level of acoustic power density in the gas.

  4. Properties of Reactive Oxygen Species by Quantum Monte Carlo

    E-Print Network [OSTI]

    Andrea Zen; Bernhardt L. Trout; Leonardo Guidoni

    2014-06-16T23:59:59.000Z

    The electronic properties of the oxygen molecule, in its singlet and triplet states, and of many small oxygen-containing radicals and anions have important roles in different fields of Chemistry, Biology and Atmospheric Science. Nevertheless, the electronic structure of such species is a challenge for ab-initio computational approaches because of the difficulties to correctly describe the statical and dynamical correlation effects in presence of one or more unpaired electrons. Only the highest-level quantum chemical approaches can yield reliable characterizations of their molecular properties, such as binding energies, equilibrium structures, molecular vibrations, charge distribution and polarizabilities. In this work we use the variational Monte Carlo (VMC) and the lattice regularized Monte Carlo (LRDMC) methods to investigate the equilibrium geometries and molecular properties of oxygen and oxygen reactive species. Quantum Monte Carlo methods are used in combination with the Jastrow Antisymmetrized Geminal Power (JAGP) wave function ansatz, which has been recently shown to effectively describe the statical and dynamical correlation of different molecular systems. In particular we have studied the oxygen molecule, the superoxide anion, the nitric oxide radical and anion, the hydroxyl and hydroperoxyl radicals and their corresponding anions, and the hydrotrioxyl radical. Overall, the methodology was able to correctly describe the geometrical and electronic properties of these systems, through compact but fully-optimised basis sets and with a computational cost which scales as $N^3-N^4$, where $N$ is the number of electrons. This work is therefore opening the way to the accurate study of the energetics and of the reactivity of large and complex oxygen species by first principles.

  5. Conduct of Operations

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2010-06-29T23:59:59.000Z

    This Order defines the requirements for establishing and implementing Conduct of Operations Programs at Department of Energy (DOE), including National Nuclear Security Administration (NNSA), facilities and projects. Cancels DOE O 5480.19. Admin Chg 1, dated 6-25-13, cancels DOE O 422.1. Certified 12-3-14.

  6. Conduct of Operations

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2010-06-29T23:59:59.000Z

    This Order defines the requirements for establishing and implementing Conduct of Operations Programs at Department of Energy (DOE), including National Nuclear Security Administration (NNSA), facilities and projects. Cancels DOE O 5480.19. Admin Chg 2, dated 12-3-14, cancels Admin Chg 1.

  7. OPERATIONAL RISK RODNEY COLEMAN

    E-Print Network [OSTI]

    Coleman, Rodney

    is entered into with the aim of generating wealth, in the pursuit of returns Wiley Encyclopedia of Operations, not only because losses are widely expressed in monetary terms but also since the industry is highly the loss events are penalties imposed for contravening regulations, they enter the public domain. Onetime

  8. Structuring Structural Operational

    E-Print Network [OSTI]

    Mousavi, Mohammad

    aan de Technische Universiteit Eindhoven, op gezag van de Rector Magnificus, prof.dr.ir. C.J. van.A. Reniers CIP­DATA LIBRARY TECHNISCHE UNIVERSITEIT EINDHOVEN Mousavi, MohammadReza Structuring Structural Operational Semantics / MohammadReza Mousavi. ­ Eindhoven : Technische Universiteit Eindhoven, 2005

  9. Structuring Structural Operational

    E-Print Network [OSTI]

    Reniers, Michel

    aan de Technische Universiteit Eindhoven, op gezag van de Rector Magnificus, prof.dr.ir. C.J. van.A. Reniers CIP-DATA LIBRARY TECHNISCHE UNIVERSITEIT EINDHOVEN Mousavi, MohammadReza Structuring Structural Operational Semantics / MohammadReza Mousavi. - Eindhoven : Technische Universiteit Eindhoven, 2005

  10. REACTOR OPERATIONS AND CONTROL

    E-Print Network [OSTI]

    Pázsit, Imre

    REACTOR OPERATIONS AND CONTROL KEYWORDS: core calculations, neural networks, control rod elevation of a control rod, or a group of control rods, is an important parameter from the viewpoint of reactor control DETERMINATION OF PWR CONTROL ROD POSITION BY CORE PHYSICS AND NEURAL NETWORK METHODS NINOS S. GARIS* and IMRE

  11. Installing and operating FEGTEMs

    SciTech Connect (OSTI)

    Hetherington, C.J.; Cullis, A.G.; Walker, S.; Turner, J.; Nelson, E.C.; O'Keefe, M.A.

    1997-11-03T23:59:59.000Z

    In order to operate at full potential, Field-Emission-Gun Transmission Electron Microscopes (FEG-TEMs) require special environments designed to minimize the effects of vibration and electromagnetic noise. This report shows how careful attention to these details can enable such instruments to achieve their design parameters and produce information transfer to sub-Angstrom resolutions.

  12. Operation and Maintenance

    E-Print Network [OSTI]

    van Hemmen, J. Leo

    in this Publication is provided as is and has been prepared solely for the purpose of evaluating data center designOperation and Maintenance InRow® RD Air Cooled ACRD100 ACRD101 #12;This manual is available assumes no liability for damages, violations of codes, improper installation, system failures, or any

  13. Intelligent Potroom Operation

    SciTech Connect (OSTI)

    Jan Berkow; Larry Banta

    2003-07-29T23:59:59.000Z

    The Intelligent Potroom Operation project focuses on maximizing the performance of an aluminum smelter by innovating components for an intelligent manufacturing system. The Intelligent Potroom Advisor (IPA) monitors process data to identify reduction cells exhibiting behaviors that require immediate attention. It then advises operational personnel on those heuristic-based actions to bring the cell back to an optimal operating state in order to reduce the duration and frequency of substandard reduction cell performance referred to as ''Off-Peak Modes'' (OPMs). Techniques developed to identify cells exhibiting OPMs include the use of a finite element model-based cell state estimator for defining the cell's current operating state via advanced cell noise analyses. In addition, rule induction was also employed to identify statistically significant complex behaviors that occur prior to OPMs. The intelligent manufacturing system design, concepts and formalisms developed in this project w ere used as a basis for an intelligent manufacturing system design. Future research will incorporate an adaptive component to automate continuous process improvement, a technology platform with the potential to improve process performance in many of the other Industries of the Future applications as well.

  14. Safe Chain Saw Operation

    E-Print Network [OSTI]

    Nelson, Gary S.

    1982-01-01T23:59:59.000Z

    Z TA24S.7 8873 NO.1409 B-1409 SAFE CHAIN SAW OPERATION Gary S. Nelson* A chain saw is a portable power cutting machine. Used properly, it will trim or cut down trees, clear land or cut fireplace wood. Improperly used, a chain saw can...

  15. DCO Operations Interesting Statistics

    E-Print Network [OSTI]

    DRY BULB TEMPERATURE - °F 01 51 02 52 03 53 04 54 05 55 55 06 06 RIAYRDFODNUOPREPUTB-YPLAHTNE ENTHALPY - BTU PER POUND OF DRY AIR 51 02 52 03 53 04 54 05 RIA YRD F O DNU OP REP UTB- YPLAHTNE F°- ERUTAREP MET operate 1560 hard disks, totaling 530 TB of storage · Eight air conditioners within the zones process

  16. Concept of Operations: Essence

    SciTech Connect (OSTI)

    Hutton, William J.

    2014-04-01T23:59:59.000Z

    This concept of operations is designed to give the reader a brief overview of the National Rural Electric Cooperative Association’s Essence project and a description of the Essence device design. The data collected by the device, how the data are used, and how the data are protected are also discussed in this document.

  17. Office of Business Operations

    Broader source: Energy.gov [DOE]

    The Office of Business Operations manages financial and acquisition management programs throughout the Associate Under Secretary for the Office of Environment, Health, Safety and Security (AU), including the formulation and execution of the AU budget; funding control and accounting activities; preparation of management studies; and provision of acquisition management support.

  18. A transport based one-dimensional perturbation code for reactivity calculations in metal systems

    SciTech Connect (OSTI)

    Wenz, T.R.

    1995-02-01T23:59:59.000Z

    A one-dimensional reactivity calculation code is developed using first order perturbation theory. The reactivity equation is based on the multi-group transport equation using the discrete ordinates method for angular dependence. In addition to the first order perturbation approximations, the reactivity code uses only the isotropic scattering data, but cross section libraries with higher order scattering data can still be used with this code. The reactivity code obtains all the flux, cross section, and geometry data from the standard interface files created by ONEDANT, a discrete ordinates transport code. Comparisons between calculated and experimental reactivities were done with the central reactivity worth data for Lady Godiva, a bare uranium metal assembly. Good agreement is found for isotopes that do not violate the assumptions in the first order approximation. In general for cases where there are large discrepancies, the discretized cross section data is not accurately representing certain resonance regions that coincide with dominant flux groups in the Godiva assembly. Comparing reactivities calculated with first order perturbation theory and a straight {Delta}k/k calculation shows agreement within 10% indicating the perturbation of the calculated fluxes is small enough for first order perturbation theory to be applicable in the modeled system. Computation time comparisons between reactivities calculated with first order perturbation theory and straight {Delta}k/k calculations indicate considerable time can be saved performing a calculation with a perturbation code particularly as the complexity of the modeled problems increase.

  19. Comparison of Alternative Control Structures for an Ideal Two-Product Reactive Distillation Column

    E-Print Network [OSTI]

    Al-Arfaj, Muhammad A.

    Comparison of Alternative Control Structures for an Ideal Two-Product Reactive Distillation Column distillation columns have been explored in many papers, very few papers have dealt with closed-loop control. Most of these control papers consider reactive distillation columns in which there is only one product

  20. Design of Extraction Column Methanol Recovery System for the TAME Reactive Distillation Process

    E-Print Network [OSTI]

    Al-Arfaj, Muhammad A.

    Design of Extraction Column Methanol Recovery System for the TAME Reactive Distillation Process system for TAME reactive distillation process using extraction column with water as a solvent. The design distillation column which was optimized to recover methanol and recycle water to the extraction column. Other

  1. Analytical solutions for sequentially coupled one-dimensional reactive transport problems Part II: Special cases,

    E-Print Network [OSTI]

    Clement, Prabhakar

    Analytical solutions for sequentially coupled one-dimensional reactive transport problems ­ Part II solutions to multi-species reactive transport equations coupled through sorption and sequential first special-case transport scenarios involving zero initial condition, identical retardation factors and zero

  2. A gas-kinetic scheme for reactive ows Yongsheng Lian, Kun Xu*

    E-Print Network [OSTI]

    Xu, Kun

    A gas-kinetic scheme for reactive ¯ows Yongsheng Lian, Kun Xu* Department of Mathematics, Hong Kong in revised form 22 July 1999; accepted 22 July 1999 Abstract In this paper, the gas-kinetic BGK scheme for the compressible ¯ow equations is extended to chemical reactive ¯ow. The mass fraction of the unburnt gas

  3. Comparison of reactivity measurements using water height, rods, and boron poison in the CX-SNTP

    SciTech Connect (OSTI)

    Ball, R.M. [B& W Nuclear Environmental Services, Inc., Lynchburg, VA (United States); Hoovler, G.S. [Babcock & Wilcox, Lynchburg, VA (United States)

    1995-12-31T23:59:59.000Z

    Babcock & Wilcox (B&W) designed and fabricated the experimental nuclear reactor (CX), for the Space Nuclear Thermal Propulsion (SNTP) program sponsored by the U.S. Air Force. The CX had an excess reactivity between $2.0 and $2.5. Variations in differential boric acid worth depending on the method used for balancing the reactivity are discussed in this paper.

  4. Synthesis, Characterization and Reactivity of Electrophilic Organometallic Compounds of Ruthenium, Tantalum and Silicon

    E-Print Network [OSTI]

    Ramirez, Rodrigo

    2014-12-11T23:59:59.000Z

    SYNTHESIS, CHARACTERIZATION AND REACTIVITY OF ELECTROPHILIC ORGANOMETALLIC COMPOUNDS OF RUTHENIUM, TANTALUM AND SILICON A Dissertation by RODRIGO RAMIREZ Submitted to the Office of Graduate and Professional Studies of Texas A... December 2014 Major Subject: Chemistry Copyright 2014 Rodrigo Ramírez ii ABSTRACT The work presented herein will discuss the synthesis, characterization and reactivity of electrophilic organometallic compounds of ruthenium, tantalum...

  5. PEV-based Reactive Power Compensation for Wind DG Units: A Stackelberg Game Approach

    E-Print Network [OSTI]

    Mohsenian-Rad, Hamed

    balancing supply and demand for active power, we also need to compensate reactive power for each wind DGPEV-based Reactive Power Compensation for Wind DG Units: A Stackelberg Game Approach Chenye Wu, in particular wind power, in form of distributed generation (DG) units. However, one important challenge

  6. PEV-based Reactive Power Compensation for Wind DG Units: A Stackelberg Game Approach

    E-Print Network [OSTI]

    Huang, Jianwei

    balancing supply and demand for active power, we also need to compensate reactive power for each wind DG1 PEV-based Reactive Power Compensation for Wind DG Units: A Stackelberg Game Approach Chenye Wu, in particular wind power, in form of distributed generation (DG) units. However, one important challenge

  7. Learning Reactive Neurocontrollers using Simulated Annealing for Mobile Philippe Lucidarme, Alain Ligeois

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Learning Reactive Neurocontrollers using Simulated Annealing for Mobile Robots Philippe Lucidarme a method based on simulated annealing to learn reactive behaviors. This work is related with multi is a neural network and we use a simulated annealing techniques to learn the synaptic weights. We'll first

  8. Intelligent Voltage and Reactive Power Control of Mini-Hydro Power Stations for Maximisation of Real

    E-Print Network [OSTI]

    Harrison, Gareth

    1 Intelligent Voltage and Reactive Power Control of Mini-Hydro Power Stations for Maximisation Control (APFC) modes. The ability to export active and reactive power from mini-hydro power generators electrical power generation from renewable resources. Additionally, the potential early retiral of central

  9. Small Inverter-Interfaced Distributed Energy Resources for Reactive Power Support

    E-Print Network [OSTI]

    Liberzon, Daniel

    to provide reactive power support. I. INTRODUCTION Electrical generators connected to ac power grids mustSmall Inverter-Interfaced Distributed Energy Resources for Reactive Power Support Alejandro D. Dom´inguez-Garc´ia, Christoforos N. Hadjicostis, Philip T. Krein, and Stanton T. Cady Department of Electrical and Computer

  10. Specification and Design of Reactive Systems B.S. (National Chiao-Tung University) 1991

    E-Print Network [OSTI]

    of Reactive Systems by Bilung Lee Doctor of Philosophy in Engineering ­ Electrical Engineering and ComputerSpecification and Design of Reactive Systems by Bilung Lee B.S. (National Chiao-Tung University of the requirements for the degree of Doctor of Philosophy in Engineering ­ Electrical Engineering and Computer

  11. Parameters of Postocclusive Reactive Hyperemia Measured by Near Infrared Spectroscopy in Patients with Peripheral Vascular

    E-Print Network [OSTI]

    Ljubljana, University of

    Parameters of Postocclusive Reactive Hyperemia Measured by Near Infrared Spectroscopy in Patients PRESERN-STRUKELJ,2 and DAMIJAN MIKLAVC IC 1 1 University of Ljubljana, Faculty of Electrical Engineering study was to determine the parameters of the postocclusive reactive hyperemia test that could help

  12. IEEE TRANSACTIONS ON POWER SYSTEMS (ACCEPTED NOVEMBER 8, 2014) 1 Stochastic Reactive Power Management

    E-Print Network [OSTI]

    Giannakis, Georgios

    IEEE TRANSACTIONS ON POWER SYSTEMS (ACCEPTED NOVEMBER 8, 2014) 1 Stochastic Reactive Power response, and electric vehicles. Advances in photovoltaic (PV) inverters offer new opportunities for reactive power management provided PV owners have the right invest- ment incentives. In this context

  13. Intelligent Network-Layer Management for Wireless Mesh Networks: Dynamic Tuning of a Reactive Routing Protocol

    E-Print Network [OSTI]

    Kolner, Brian H.

    1 Intelligent Network-Layer Management for Wireless Mesh Networks: Dynamic Tuning of a Reactive Routing Protocol Dan Marconett, Minsoo Lee, Xiaohui Ye and S. J. Ben Yoo Dept. of Electrical and Computer learning to dynamically modify reactive routing protocol parameters in real-time, to better facilitate

  14. Automatic Testing of Reactive Systems \\Lambda Pascal Raymond, Xavier Nicollin, Nicolas Halbwachs y

    E-Print Network [OSTI]

    Halbwachs, Nicolas

    Automatic Testing of Reactive Systems \\Lambda Pascal Raymond, Xavier Nicollin, Nicolas Halbwachs y V'erimag z , Grenoble ­ France Daniel Weber x Schneider Electric, Grenoble ­ France Abstract This paper addresses the problem of automatizing the production of test sequences for reactive systems. We

  15. Stability of planar reactive fronts in external fields Arkady B. Rovinsky,* Anatol M. Zhabotinsky,

    E-Print Network [OSTI]

    Epstein, Irving R.

    in reactive systems due to external fields such as electric fields or pressure gradients, may significantlyStability of planar reactive fronts in external fields Arkady B. Rovinsky,* Anatol M. Zhabotinsky arise naturally in systems sub- jected to external fields, such as electric fields or pressure gradients

  16. European Wind Energy Conference 2007 Milan Measurement based analysis of active and reactive power

    E-Print Network [OSTI]

    European Wind Energy Conference 2007 ­ Milan 1 Measurement based analysis of active and reactive of the electricity is produced by wind turbines and combined heat and power plants (CHPs). Most of them are connected of reactive power between the 60 kV and the 150 kV networks. Further, the TSO is obligated to compensate

  17. MEASURING REACTIVE MARKET POWER Fernando L. Alvarado Thomas Overbye Peter Sauer

    E-Print Network [OSTI]

    MEASURING REACTIVE MARKET POWER Fernando L. Alvarado Thomas Overbye Peter Sauer The University-Hirschman Index) can be used to measure reactive power market concentration. The proposed method is illustrated by means of a simple example. Keywords: Electric power transmission, monopoly, mar- ket concentration. 1

  18. Rollable multicolor display using electrically induced blueshift of a cholesteric reactive mesogen mixture

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Rollable multicolor display using electrically induced blueshift of a cholesteric reactive mesogen September 2006 Electrically controllable blueshift of the reflection band in a planar cholesteric reactive mesogen cell is observed. The responsible mechanism is electric-field-induced Helfrich deformation J. Chem

  19. PATHS: Analysis of PATH Duration Statistics and their Impact on Reactive MANET Routing Protocols

    E-Print Network [OSTI]

    Krishnamachari, Bhaskar

    PATHS: Analysis of PATH Duration Statistics and their Impact on Reactive MANET Routing Protocols Department of Electrical Engineering University of Southern California {narayans,fbai,bkrishna,helmy}@usc.edu ABSTRACT We develop a detailed approach to study how mobility im- pacts the performance of reactive MANET

  20. 39333939 ORNL/TM-2008/174 Local Dynamic Reactive Power for

    E-Print Network [OSTI]

    Pennycook, Steve

    39333939 ORNL/TM-2008/174 Local Dynamic Reactive Power for Correction of System Voltage Problems Local Dynamic Reactive Power for Correction of System Voltage Problems John D. Kueck* D. Tom Rizy Group at Oak Ridge National Laboratory Professor of Electrical Engineering at University of Tennessee

  1. Age-Related Differences in Emotional Reactivity, Regulation, and Rejection Sensitivity in Adolescence

    E-Print Network [OSTI]

    Ochsner, Kevin

    Age-Related Differences in Emotional Reactivity, Regulation, and Rejection Sensitivity Massachusetts Institute of Technology James J. Gross Stanford University Katherine A. Remy and Kevin N. Ochsner reactivity or emotion regulation. Study 1 addressed this question by presenting healthy individuals aged 10

  2. Concentrations and Snow-Atmosphere Fluxes of Reactive Nitrogen at Summit, Greenland

    E-Print Network [OSTI]

    1 Concentrations and Snow-Atmosphere Fluxes of Reactive Nitrogen at Summit, Greenland J. W. Munger AT SUMMIT, GREENLAND 2 Abstract. Concentrations and fluxes of NOy (total reactive nitrogen), ozone concentra at Summit, Greenland. Median NOy concentrations declined from 947 ppt in May to 444 ppt by July. NOy fluxes

  3. Lycopene cyclase paralog CruP protects against reactive oxygen species in oxygenic

    E-Print Network [OSTI]

    Wurtzel, Eleanore

    , quenching singlet oxygen generated during the water-splitting process of photo- synthesis (10, 11). VariousLycopene cyclase paralog CruP protects against reactive oxygen species in oxygenic photosynthetic cyclase. Instead, we show that CruP aids in preventing accumulation of reactive oxygen species (ROS

  4. Reactive power management of distribution networks with wind generation for improving voltage stability

    E-Print Network [OSTI]

    Pota, Himanshu Roy

    -loadability Reactive power margin Wind turbine a b s t r a c t This paper proposes static and dynamic VAR planningReactive power management of distribution networks with wind generation for improving voltage February 2013 Available online Keywords: Composite load Distributed generation D-STATCOM Q

  5. Modeling Reactive Flows in Porous Media Peter Lichtner (lead PI), Los Alamos National Laboratory

    E-Print Network [OSTI]

    Mills, Richard

    and reactive transport in porous media. Apply it to field-scale studies of Geologic CO2 sequestrationModeling Reactive Flows in Porous Media Peter Lichtner (lead PI), Los Alamos National Laboratory NCCS Users Meeting March 28, 2007 #12;Introduction Companion to SciDAC-II project, "Modeling

  6. Passive Ozone Control Through Use of Reactive Indoor Wall and Ceiling Materials

    E-Print Network [OSTI]

    Siegel, Jeffrey

    Passive Ozone Control Through Use of Reactive Indoor Wall and Ceiling Materials Paper # 715 Donna A and unpainted drywall as passive ozone control surfaces in a room-sized laboratory chamber. Mean deposition-50%, resulted in increased reactivity for activated carbon. In our model for a typical house, about 35

  7. Relating maximum airway dilation and subsequent reconstriction to reactivity in human lungs

    E-Print Network [OSTI]

    Lutchen, Kenneth

    Relating maximum airway dilation and subsequent reconstriction to reactivity in human lungs Lauren in human lungs. J Appl Physiol 96: 1808­1814, 2004. First published February 6, 2004; 10.1152/japplphysiol reactivity in healthy lungs by prohibiting DI for an extended period. The present study had two goals. First

  8. Operations and Maintenance Program Structure

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program recommends Federal operations and maintenance (O&M) programs comprise of five distinct functions: operations, maintenance, engineering, training, and...

  9. STANDARD OPERATING PROCEDURES Sampler Maintenance by Site Operators

    E-Print Network [OSTI]

    Fischer, Emily V.

    IMPROVE STANDARD OPERATING PROCEDURES SOP 201 Sampler Maintenance by Site Operators Date Last.0 PURPOSE AND APPLICABILITY This standard operating procedure (SOP) describes the procedures and schedules. The procedural steps for weekly maintenance and repairs performed by the site operator are included in TI 201A

  10. Method for operating a nuclear reactor to accommodate load follow while maintaining a substantially constant axial power distribution

    SciTech Connect (OSTI)

    Mueller, N.P.; Rossi, C.E.; Scherpereel, L.R.

    1980-09-16T23:59:59.000Z

    This invention provides a method of operating a nuclear reactor having a negative reactivity moderator temperature coefficient with the object of maintaining a uniform and symmetric xenon distribution above and below substantially the center of the core over a substantial axial length of the core during normal reactor operation including load follow. In one embodiment variations in the xenon distribution are controlled by maintaining a substantially symmetric axial power distribution. The axial offset, which is employed as an indication of the axial power distribution, is maintained substantially equal to a target value , which is modified periodically to account for core burnup. A neutron absorbing element within the core coolant, or moderator, is employed to assist control of reactivity changes associated with changes in power, with the full-length control rods mainly employed to adjust variations in the axial power distribution while the part-length rodsremain completely withdrawn from the fuel region of the core. Rapid changes in reactivity are implemented, to accommodate corresponding changes in load, by a controlled reduction of the core coolant temperature. Thus, active core coolant temperature control is employed to control the reactivity of the core during load follow operation and effectively increase the spinning reserve capability of a power plant without altering the axial power distribution.

  11. Knowledges and abilities catalog for nuclear power plant operators: pressurized water reactors

    SciTech Connect (OSTI)

    Not Available

    1985-07-01T23:59:59.000Z

    This document catalogs roughly 5300 knowledges and abilities of reactor operators and senior reactor operators. It results from a reanalysis of much larger job-task analysis data base compiled by the Institute of Nuclear Power Operations (INPO). Knowledges and abilities are cataloged for 45 major power plant systems and 38 emergency evolutions, grouped according to 11 fundamental safety functions (e.g., reactivity control and reactor coolant system inventory control). With appropriate sampling from this catalog, operator licensing examinations having content validity can be developed. A structured sampling procedure for this catalog is under development by the Nuclear Regulatory Commission (NRC) and will be published as a companion document, ''Examiners' Handbook for Developing Operator Licensing Examinations'' (NUREG-1121). The examinations developed by using the catalog and handbook will cover those topics listed under Title 10, Code of Federal Regulations, Part 55.

  12. Hurricane slams gulf operations

    SciTech Connect (OSTI)

    Not Available

    1992-09-07T23:59:59.000Z

    This paper reports that reports of damage by Hurricane Andrew escalated last week as operators stepped up inspections of oil and gas installations in the Gulf of Mexico. By midweek, companies operating in the gulf and South Louisiana were beginning to agree that earlier assessments of damage only scratched the surface. Damage reports included scores of lost, toppled, or crippled platforms, pipeline ruptures, and oil slicks. By midweek the U.S. coast Guard had received reports of 79 oil spills. Even platforms capable of resuming production in some instances were begin curtailed because of damaged pipelines. Offshore service companies the another 2-4 weeks could be needed to fully assess Andrew's wrath. Lack of personnel and equipment was slowing damage assessment and repair.

  13. Operations Task Management (OTM)

    SciTech Connect (OSTI)

    Miller, C.B.; Duck, C.H.

    1985-10-01T23:59:59.000Z

    This paper reviews the steps taken by management at Ashland Oil to reduce expenses, including an analysis of every aspect of the refinery. It was determined that the areas most adaptable to improvement were the maintenance department, storerooms, the laboratory and energy utilization. The authors focus, however, on the difficulties met in implementing an effective cost control program in the operations area, detailing the reasons why and examining the system ultimately installed in this area.

  14. Gaussian operations and privacy

    SciTech Connect (OSTI)

    Navascues, Miguel; Acin, Antonio [ICFO-Institut de Ciencies Fotoniques, Jordi Girona 29, Edifici Nexus II, E-08034 Barcelona (Spain)

    2005-07-15T23:59:59.000Z

    We consider the possibilities offered by Gaussian states and operations for two honest parties, Alice and Bob, to obtain privacy against a third eavesdropping party, Eve. We first extend the security analysis of the protocol proposed in [Navascues et al. Phys. Rev. Lett. 94, 010502 (2005)]. Then, we prove that a generalized version of this protocol does not allow one to distill a secret key out of bound entangled Gaussian states.

  15. Operational health physics training

    SciTech Connect (OSTI)

    NONE

    1992-06-01T23:59:59.000Z

    The initial four sections treat basic information concerning atomic structure and other useful physical quantities, natural radioactivity, the properties of {alpha}, {beta}, {gamma}, x rays and neutrons, and the concepts and units of radiation dosimetry (including SI units). Section 5 deals with biological effects and the risks associated with radiation exposure. Background radiation and man-made sources are discussed next. The basic recommendations of the ICRP concerning dose limitations: justification, optimization (ALARA concepts and applications) and dose limits are covered in Section seven. Section eight is an expanded version of shielding, and the internal dosimetry discussion has been extensively revised to reflect the concepts contained in the MIRD methodology and ICRP 30. The remaining sections discuss the operational health physics approach to monitoring radiation. Individual sections include radiation detection principles, instrument operation and counting statistics, health physics instruments and personnel monitoring devices. The last five sections deal with the nature of, operation principles of, health physics aspects of, and monitoring approaches to air sampling, reactors, nuclear safety, gloveboxes and hot cells, accelerators and x ray sources. Decontamination, waste disposal and transportation of radionuclides are added topics. Several appendices containing constants, symbols, selected mathematical topics, and the Chart of the Nuclides, and an index have been included.

  16. Hanford facility dangerous waste Part A, Form 3 and Part B permit application documentation, Central Waste Complex (WA7890008967)(TSD: TS-2-4)

    SciTech Connect (OSTI)

    Saueressig, D.G.

    1998-05-20T23:59:59.000Z

    The Hanford Facility Dangerous Waste Permit Application is considered to be a single application organized into a General Information Portion (document number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to Part B permit application documentation submitted for individual, operating, treatment, storage, and/or disposal units, such as the Central Waste Complex (this document, DOE/RL-91-17). Both the General Information and Unit-Specific portions of the Hanford Facility Dangerous Waste Permit Application address the content of the Part B permit application guidance prepared by the Washington State Department of Ecology (Ecology 1996) and the U.S. Environmental Protection Agency (40 Code of Federal Regulations 270), with additional information needed by the Hazardous and Solid Waste Amendments and revisions of Washington Administrative Code 173-303. For ease of reference, the Washington State Department of Ecology alpha-numeric section identifiers from the permit application guidance documentation (Ecology 1996) follow, in brackets, the chapter headings and subheadings. A checklist indicating where information is contained in the Central Waste Complex permit application documentation, in relation to the Washington State Department of Ecology guidance, is located in the Contents section. Documentation contained in the General Information Portion is broader in nature and could be used by multiple treatment, storage, and/or disposal units (e.g., the glossary provided in the General Information Portion). Wherever appropriate, the Central Waste Complex permit application documentation makes cross-reference to the General Information Portion, rather than duplicating text. Information provided in this Central Waste Complex permit application documentation is current as of May 1998.

  17. Final Report- Rejuvenating Permeable Reactive Barriers by Chemical Flushing, U.S. Environmental Protection Agency Region 8 Support

    Broader source: Energy.gov [DOE]

    Final Report - Rejuvenating Permeable Reactive Barriers by Chemical Flushing, U.S. Environmental Protection Agency Region 8 Support

  18. Local Dynamic Reactive Power for Correction of System Voltage Problems

    SciTech Connect (OSTI)

    Kueck, John D [ORNL; Rizy, D Tom [ORNL; Li, Fangxing [ORNL; Xu, Yan [ORNL; Li, Huijuan [University of Tennessee, Knoxville (UTK); Adhikari, Sarina [ORNL; Irminger, Philip [ORNL

    2008-12-01T23:59:59.000Z

    Distribution systems are experiencing outages due to a phenomenon known as local voltage collapse. Local voltage collapse is occurring in part because modern air conditioner compressor motors are much more susceptible to stalling during a voltage dip than older motors. These motors can stall in less than 3 cycles (.05s) when a fault, such as on the sub-transmission system, causes voltage to sag to 70 to 60%. The reasons for this susceptibility are discussed in the report. During the local voltage collapse, voltages are depressed for a period of perhaps one or two minutes. There is a concern that these local events are interacting together over larger areas and may present a challenge to system reliability. An effective method of preventing local voltage collapse is the use of voltage regulation from Distributed Energy Resources (DER) that can supply or absorb reactive power. DER, when properly controlled, can provide a rapid correction to voltage dips and prevent motor stall. This report discusses the phenomenon and causes of local voltage collapse as well as the control methodology we have developed to counter voltage sag. The problem is growing because of the use of low inertia, high efficiency air conditioner (A/C) compressor motors and because the use of electric A/C is growing in use and becoming a larger percentage of system load. A method for local dynamic voltage regulation is discussed which uses reactive power injection or absorption from local DER. This method is independent, rapid, and will not interfere with conventional utility system voltage control. The results of simulations of this method are provided. The method has also been tested at the ORNL s Distributed Energy Communications and Control (DECC) Laboratory using our research inverter and synchronous condenser. These systems at the DECC Lab are interconnected to an actual distribution system, the ORNL distribution system, which is fed from TVA s 161kV sub-transmission backbone. The test results are also provided and discussed. The simulations and testing show that local voltage control from DER can prevent local voltage collapse. The results also show that the control can be provided so quickly, within 0.5 seconds, that is does not interfere with conventional utility methods.

  19. Multicomponent reactive transport modeling of uranium bioremediation field experiments

    SciTech Connect (OSTI)

    Fang, Yilin; Yabusaki, Steven B.; Morrison, Stan J.; Amonette, James E.; Long, Philip E.

    2009-10-15T23:59:59.000Z

    Biostimulation field experiments with acetate amendment are being performed at a former uranium mill tailings site in Rifle, Colorado, to investigate subsurface processes controlling in situ bioremediation of uranium-contaminated groundwater. An important part of the research is identifying and quantifying field-scale models of the principal terminal electron-accepting processes (TEAPs) during biostimulation and the consequent biogeochemical impacts to the subsurface receiving environment. Integrating abiotic chemistry with the microbially mediated TEAPs in the reaction network brings into play geochemical observations (e.g., pH, alkalinity, redox potential, major ions, and secondary minerals) that the reactive transport model must recognize. These additional constraints provide for a more systematic and mechanistic interpretation of the field behaviors during biostimulation. The reaction network specification developed for the 2002 biostimulation field experiment was successfully applied without additional calibration to the 2003 and 2007 field experiments. The robustness of the model specification is significant in that 1) the 2003 biostimulation field experiment was performed with 3 times higher acetate concentrations than the previous biostimulation in the same field plot (i.e., the 2002 experiment), and 2) the 2007 field experiment was performed in a new unperturbed plot on the same site. The biogeochemical reactive transport simulations accounted for four TEAPs, two distinct functional microbial populations, two pools of bioavailable Fe(III) minerals (iron oxides and phyllosilicate iron), uranium aqueous and surface complexation, mineral precipitation, and dissolution. The conceptual model for bioavailable iron reflects recent laboratory studies with sediments from the Old Rifle Uranium Mill Tailings Remedial Action (UMTRA) site that demonstrated that the bulk (~90%) of Fe(III) bioreduction is associated with the phyllosilicates rather than the iron oxides. The uranium reaction network includes a U(VI) surface complexation model based on laboratory studies with Old Rifle UMTRA sediments and aqueous complexation reactions that include ternary complexes (e.g., calcium-uranyl-carbonate). The bioreduced U(IV), Fe(II), and sulfide components produced during the experiments are strongly associated with the solid phases and may play an important role in long-term uranium immobilization.

  20. IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 22, NO. 4, NOVEMBER 2007 2177 Review of Reactive Power Planning: Objectives,

    E-Print Network [OSTI]

    Tolbert, Leon M.

    IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 22, NO. 4, NOVEMBER 2007 2177 Review of Reactive Power Member, IEEE, and Leon M. Tolbert, Senior Member, IEEE Abstract--The key of reactive power planning (RPP), or Var planning, is the optimal allocation of reactive power sources con- sidering location and size

  1. Tin-Based Reactive Solders for Ceramic/Metal Joints RAKESH R. KAPOOR and THOMAS W . EAGAR

    E-Print Network [OSTI]

    Eagar, Thomas W.

    ( { ) Tin-Based Reactive Solders for Ceramic/Metal Joints RAKESH R. KAPOOR and THOMAS W . EAGAR engine com- ponents), wear parts, tool materials, electrical feed- throughs, and metal contacts on ceramics. To overcome this problem, reactive metals are added to the filler metai.11- 181These reactive

  2. 718 IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY, VOL. 9, NO. 5, SEPTEMBER 2001 Reactive Power and Unbalance Compensation Using

    E-Print Network [OSTI]

    Stankoviæ, Aleksandar

    718 IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY, VOL. 9, NO. 5, SEPTEMBER 2001 Reactive Power as reactive power and unbalance compensators, e.g., Static synchronous compensator (STATCOM). The approach practice. Index Terms--Active filters, adaptive control, dissipative sys- tems, nonlinear systems, reactive

  3. IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 17, NO. 2, MAY 2002 283 Unbundled Reactive Support Service: Key

    E-Print Network [OSTI]

    Gross, George

    in the acquisition and pricing of the reactive support service. Index Terms--Ancillary services, electricity marketsIEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 17, NO. 2, MAY 2002 283 Unbundled Reactive Support Service exposition of generator-provided reactive support as an unbundled ancillary service under open access

  4. IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 6, NOVEMBER 2008 2905 Eliminate Reactive Power and Increase System

    E-Print Network [OSTI]

    Mi, Chunting "Chris"

    IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 6, NOVEMBER 2008 2905 Eliminate Reactive Power of "reactive power" is de- fined, and the corresponding equations are derived for isolated bidirectional dc­dc converters. It is shown that the reactive power in traditional phase-shift control is inherent

  5. IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 17, NO. 2, MAY 2002 243 Allocation of the Reactive Power Support

    E-Print Network [OSTI]

    Gross, George

    IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 17, NO. 2, MAY 2002 243 Allocation of the Reactive Power the reactive power support requirements pro- vided by the generators in multitransaction networks. The allocat- able reactive support requirements are defined with respect to the support required for the network

  6. Abstract: In this paper we provide a systematic review of generator-provided reactive support as an unbundled ancillary

    E-Print Network [OSTI]

    , the provision of reactive power and voltage support was bundled with other services in supplying electricity electricity. Under open access, however, reactive support and voltage control from generation sources becomes1 Abstract: In this paper we provide a systematic review of generator-provided reactive support

  7. Abstract--This paper proposes a reactive power dispatch model that takes into account both the technical and economical

    E-Print Network [OSTI]

    Cañizares, Claudio A.

    the reactive power and voltage control practices in all North American Electric Reliability Council (NERC and transformers taps deviations [12]. In the context of deregulated electricity markets, reactive power dispatch1 Abstract--This paper proposes a reactive power dispatch model that takes into account both

  8. INHIBITION OF CASPASE-LIKE ACTIVITIES PREVENTS THE APPEARANCE OF REACTIVE OXYGEN SPECIES AND DARK-INDUCED APOPTOSIS

    E-Print Network [OSTI]

    Berges, John A.

    cells revealed by SYTOX-green staining, and the generation of reactive oxygen species (ROS), we usedINHIBITION OF CASPASE-LIKE ACTIVITIES PREVENTS THE APPEARANCE OF REACTIVE OXYGEN SPECIES AND DARK viability; Dunaliella tertiolecta; phosphatidylserine; phytoplankton; reactive oxygen species; unicellular

  9. RESUS-D-12-00285 Mild hypothermia reduces per-ischemic reactive oxygen species production4

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    this dysfunction through per-ischemic3 inhibition of reactive oxygen species (ROS) generation.4 Methods: First, ROS ischemic injuries through complex events2 involving reactive oxygen species (ROS) generation 1, 2RESUS-D-12-00285 1 2 3 Mild hypothermia reduces per-ischemic reactive oxygen species production4

  10. Reactivity of iron-bearing minerals and CO2 sequestration: A multi-disciplinary experimental approach

    SciTech Connect (OSTI)

    Schoonen, Martin A. [Stony Brook University] (ORCID:0000000271331160)

    2014-12-22T23:59:59.000Z

    The reactivity of sandstones was studied under conditions relevant to the injection of supercritical carbon dioxide in the context of carbon geosequestration. The emphasis of the study was on the reactivity of iron-bearing minerals when exposed to supercritical CO2 (scCO2) and scCO2 with commingled aqueous solutions containing H2S and/or SO2. Flow through and batch experiments were conducted. Results indicate that sandstones, irrespective of their mineralogy, are not reactive when exposed to pure scCO2 or scCO2 with commingled aqueous solutions containing H2S and/or SO2 under conditions simulating the environment near the injection point (flow through experiments). However, sandstones are reactive under conditions simulating the edge of the injected CO2 plume or ahead of the plume (batch experiments). Sandstones containing hematite (red sandstone) are particularly reactive. The composition of the reaction products is strongly dependent on the composition of the aqueous phase. The presence of dissolved sulfide leads to the conversion of hematite into pyrite and siderite. The relative amount of the pyrite and siderite is influenced by the ionic strength of the solution. Little reactivity is observed when sulfite is present in the aqueous phase. Sandstones without hematite (grey sandstones) show little reactivity regardless of the solution composition.

  11. Spectroscopy, Thermochemistry, and Reactivity of Lanthanide and Actinide Molecules

    SciTech Connect (OSTI)

    Morse, Michael D.; Armentrout, Peter B.

    2012-08-16T23:59:59.000Z

    The research undertaken under this grant is described in this document. The document describes progress in the construction of an instrument for recording photodissociation action spectra of mass-selected cryo-cooled cations. The instrument is not yet functional, but we anticipate trapping ions and conducting photodissociation experiments before the end of the year. It also describes resonant two-photon ionization spectra that have been recorded for uranium mononitride (UN) in the visible portion of the spectrum. These experiments are still underway at the present time. Although the spectra are a bit difficult to properly fit, due to upper state perturbations, it appears that the molecule has a ground state with {Omega} = 3.5 and a bond length of approximately 1.76 {angstrom}. Finally, results on the thermochemistry and reactivity of Th{sup +} are presented. In these studies the bond energies of the following bonds have been determined: D{sub 0}(Th{sup +}-2O) = 10.2 {+-} 0.2 eV; D0(Th{sup +}-N) = 6.69 {+-} 0.35 eV; D0(Th{sup +}-O) = 8.40 {+-} 0.28 eV; D{sub 0}(OTh{sup +}-O) = 1.8 {+-} 0.4 eV.

  12. Permeable reactive barrier technologies for contaminant remediation. Interim report

    SciTech Connect (OSTI)

    Powell, R.M.; Puls, R.W.; Blowes, D.W.; Gillham, R.W.; Schultz, D.

    1998-09-01T23:59:59.000Z

    This document addresses the factors that have been found to be relevant for successfully implementing PRBs for contaminant remediation. Additionally, it provides sufficient background in the science of PRB technology to allow a basic understanding of the chemical reactions proposed for the contaminant transformations that have been witnessed both in the laboratory and in field settings. It contains sections on PRB-treatable contaminants and the treatment reaction mechanisms, feasibility studies for PRB implementation, site characterization for PRBs, PRB design, PRB emplacement, monitoring for both compliance and performance, and summaries of several field installations. The appendices supplement this information with a detailed table of information available in the literature through 1997, summarizing the significant findings of PRB research and field studies (Appendix A), a further examination of the physical and chemical processes important to PRBs, such as corrosion, adsorption, and precipitation (Appendix B), and a set of scoping calculations that can be used to estimate the amount of reactive media required and facilitate choosing among te possible means of emplacing the required amount of media (Appendix C). Appendix D provides a list of acronyms and Appendix E a glossary of terms that are used within this document.

  13. ESTIMATING THE UNCERTAINTY IN REACTIVITY ACCIDENT NEUTRONIC CALCULATIONS

    SciTech Connect (OSTI)

    DIAMOND,D.J.; YANG,C.Y.; ARONSON,A.L.

    1998-10-26T23:59:59.000Z

    A study of the uncertainty in calculations of the rod ejection accident in a pressurized water reactor is being carried out for the US Nuclear Regulatory Commission. This paper is a progress report on that study. Results are presented for the sensitivity of core energy deposition to the key parameters: ejected rod worth, delayed neutron fraction, Doppler reactivity coefficient, and fuel specific heat. These results can be used in the future to estimate the uncertainty in local fuel enthalpy given some assumptions about the uncertainty in the key parameters. This study is also concerned with the effect of the intra-assembly representation in calculations. The issue is the error that might be present if assembly-average power is calculated, and pin peaking factors from a static calculation are then used to determine local fuel enthalpy. This is being studied with the help of a collaborative effort with Russian and French analysts who are using codes with different intra-assembly representations. The US code being used is PARCS which calculates power on an assembly-average basis. The Russian code being used is BARS which calculates power for individual fuel pins using a heterogeneous representation based on a Green's Function method.

  14. Estimating the uncertainty in reactivity accident neutronic calculations

    SciTech Connect (OSTI)

    Diamond, D.J.; Yang, C.Y.; Aronson, A.L.

    1998-12-31T23:59:59.000Z

    A study of the uncertainty in calculations of the rod ejection accident in a pressurized water reactor is being carried out for the US Nuclear Regulatory Commission. This paper is a progress report on that study. Results are presented for the sensitivity of core energy deposition to the key parameters: ejected rod worth, delayed neutron fraction, Doppler reactivity coefficient, and fuel specific heat. These results can be used in the future to estimate the uncertainty in local fuel enthalpy given some assumptions about the uncertainty in the key parameters. This study is also concerned with the effect of the intra-assembly representation in calculations. The issue is the error that might be present if assembly-average power is calculated, and pin peaking factors from a static calculation are then used to determine local fuel enthalpy. This is being studied with the help of a collaborative effort with Russian and French analysts who are using codes with different intra-assembly representations. The US code being used is PARCS which calculates power on an assembly-average basis. The Russian code being used is BARS which calculates power for individual fuel pins using a heterogeneous representation based on a Green`s Function method.

  15. Predictive modeling of reactive wetting and metal joining.

    SciTech Connect (OSTI)

    van Swol, Frank B.

    2013-09-01T23:59:59.000Z

    The performance, reproducibility and reliability of metal joints are complex functions of the detailed history of physical processes involved in their creation. Prediction and control of these processes constitutes an intrinsically challenging multi-physics problem involving heating and melting a metal alloy and reactive wetting. Understanding this process requires coupling strong molecularscale chemistry at the interface with microscopic (diffusion) and macroscopic mass transport (flow) inside the liquid followed by subsequent cooling and solidification of the new metal mixture. The final joint displays compositional heterogeneity and its resulting microstructure largely determines the success or failure of the entire component. At present there exists no computational tool at Sandia that can predict the formation and success of a braze joint, as current capabilities lack the ability to capture surface/interface reactions and their effect on interface properties. This situation precludes us from implementing a proactive strategy to deal with joining problems. Here, we describe what is needed to arrive at a predictive modeling and simulation capability for multicomponent metals with complicated phase diagrams for melting and solidification, incorporating dissolutive and composition-dependent wetting.

  16. Etching radical controlled gas chopped deep reactive ion etching

    DOE Patents [OSTI]

    Olynick, Deidre; Rangelow, Ivo; Chao, Weilun

    2013-10-01T23:59:59.000Z

    A method for silicon micromachining techniques based on high aspect ratio reactive ion etching with gas chopping has been developed capable of producing essentially scallop-free, smooth, sidewall surfaces. The method uses precisely controlled, alternated (or chopped) gas flow of the etching and deposition gas precursors to produce a controllable sidewall passivation capable of high anisotropy. The dynamic control of sidewall passivation is achieved by carefully controlling fluorine radical presence with moderator gasses, such as CH.sub.4 and controlling the passivation rate and stoichiometry using a CF.sub.2 source. In this manner, sidewall polymer deposition thicknesses are very well controlled, reducing sidewall ripples to very small levels. By combining inductively coupled plasmas with controlled fluorocarbon chemistry, good control of vertical structures with very low sidewall roughness may be produced. Results show silicon features with an aspect ratio of 20:1 for 10 nm features with applicability to nano-applications in the sub-50 nm regime. By comparison, previous traditional gas chopping techniques have produced rippled or scalloped sidewalls in a range of 50 to 100 nm roughness.

  17. IBRD Operational Decision Framework

    SciTech Connect (OSTI)

    Greenwalt, R; Hibbard, W; Raber, E; Carlsen, T; Folks, K; MacQueen, D; Mancieri, S; Bunt, T; Richards, J; Hirabayashi-Dethier, J

    2010-11-12T23:59:59.000Z

    The IBRD Operational Decision Framework in this document is an expansion of an emerging general risk management framework under development by an interagency working group. It provides the level of detail necessary to develop a general Consequence Management Guidance Document for biological contamination remediation and restoration. It is the intent of this document to support both wide area and individual site remediation and restoration activities. This product was initiated as a portion of the IBRD Task 1 Systems Analysis to aid in identification of wide area remediation and restoration shortcomings and gaps. The draft interagency general risk management framework was used as the basis for the analysis. The initial Task 1 analysis document expanded the draft interagency framework to a higher level of resolution, building on both the logic structure and the accompanying text explanations. It was then employed in a qualitative manner to identify responsible agencies, data requirements, tool requirements, and current capabilities for each decision and task. This resulted in identifying shortcomings and gaps needing resolution. Several meetings of a joint LLNL/SNL working group reviewed and approved the initial content of this analysis. At the conclusion of Task 1, work continued on the expanded framework to generate this Operational Decision Framework which is consistent with the existing interagency general risk management framework. A large LLNL task group met repeatedly over a three-month period to develop the expanded framework, coordinate the framework with the biological remediation checklist, and synchronize the logic with the Consequence Management Plan table of contents. The expanded framework was briefed at a large table top exercise reviewing the interagency risk management framework. This exercise had representation from major US metropolitan areas as well as national agencies. This product received positive comments from the participants. Upon completion of the Operational Decision Framework, another joint LLNL/SNL working group conducted a day-long review. Identified modifications were made to the document, resulting in the included product.

  18. Equipment Operational Requirements

    SciTech Connect (OSTI)

    Greenwalt, B; Henderer, B; Hibbard, W; Mercer, M

    2009-06-11T23:59:59.000Z

    The Iraq Department of Border Enforcement is rich in personnel, but poor in equipment. An effective border control system must include detection, discrimination, decision, tracking and interdiction, capture, identification, and disposition. An equipment solution that addresses only a part of this will not succeed, likewise equipment by itself is not the answer without considering the personnel and how they would employ the equipment. The solution should take advantage of the existing in-place system and address all of the critical functions. The solutions are envisioned as being implemented in a phased manner, where Solution 1 is followed by Solution 2 and eventually by Solution 3. This allows adequate time for training and gaining operational experience for successively more complex equipment. Detailed descriptions of the components follow the solution descriptions. Solution 1 - This solution is based on changes to CONOPs, and does not have a technology component. It consists of observers at the forts and annexes, forward patrols along the swamp edge, in depth patrols approximately 10 kilometers inland from the swamp, and checkpoints on major roads. Solution 2 - This solution adds a ground sensor array to the Solution 1 system. Solution 3 - This solution is based around installing a radar/video camera system on each fort. It employs the CONOPS from Solution 1, but uses minimal ground sensors deployed only in areas with poor radar/video camera coverage (such as canals and streams shielded by vegetation), or by roads covered by radar but outside the range of the radar associated cameras. This document provides broad operational requirements for major equipment components along with sufficient operational details to allow the technical community to identify potential hardware candidates. Continuing analysis will develop quantities required and more detailed tactics, techniques, and procedures.

  19. Parastillation Process in Operations

    E-Print Network [OSTI]

    Canfield, F.; Jenkins, O.

    PARASTII.IMICN PIO:ESS rn OPERATIONS Frank canfield ChenShare Coq:oration Houston, Texas The Parastillation process is a new rrethod for ITU.11ti-stage, counter-current contact between vapor and liquid that results in 33% rrore ideal stages... than distillation for a given tray spaci.n;J. Patents have been granted in the U.S.A., U.K., Europe and other countries. Perfonnance of the process has been confimm aver the past several years by eat1puter siITU.llation, by laboratory tests...

  20. Operations | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > TheNuclear Astrophysics One ofSpeedingthis site »Operations Welcome to

  1. Operations Research Analysts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)IntegratedSpeeding access toTest and EvaluationOperational ManagementCenter

  2. Oak Ridge Operations

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA groupTuba City, Arizona,Site Operations Guide Doc. No.GS05:or _^r a2012

  3. Oak Ridge Operations YTO

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA groupTuba City, Arizona,Site Operations Guide Doc. No.GS05:or _^r a2012IC77GLged

  4. Oak Ridge Operations.

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA groupTuba City, Arizona,Site Operations Guide Doc. No.GS05:or _^r a2012IC77GLged

  5. SO{sub 2} reactivity studies with BENMOL sorbents - CRADA 90-002. Final report

    SciTech Connect (OSTI)

    Markussen, J.M.; Pennline, H.W.; Brodd, C.F. [Dept. of Energy Pittsburgh Energy Technology Center, PA (United States)]|[BENMOL Corp., Alexandria, VA (United States)

    1990-12-01T23:59:59.000Z

    BENMOL sorbents have been purported to be reactive with sulfur dioxide (SO{sub 2}) in flue gas at post-air-preheater temperatures (350{degrees}F and below), thus making them possible candidates for dry sorbent injection desulfurization processes. As an initial step to determine the reactivity of these sorbents, microbalance studies were conducted at the Pittsburgh Energy Technology Center (PETC) under the Cooperative Research and Development Agreement (CRADA) program. Initial reactivity rates and total absorption capacities were determined and compared to those obtained with hydrated lime, which is the chosen sorbent for most duct injection flue gas desulfurization processes.

  6. Chromium-Removal Processes during Groundwater Remediation by a Zerovalent Iron Permeable Reactive Barrier

    SciTech Connect (OSTI)

    Wilkin, Richard T.; Su, Chunming; Ford, Robert G.; Paul, Cynthia J. (US EPA)

    2008-06-09T23:59:59.000Z

    Solid-phase associations of chromium were examined in core materials collected from a full-scale, zerovalent iron permeable reactive barrier (PRB) at the U.S. Coast Guard Support Center located near Elizabeth City, NC. The PRB was installed in 1996 to treat groundwater contaminated with hexavalent chromium. After eight years of operation, the PRB remains effective at reducing concentrations of Cr from average values >1500 {micro}g L{sup -1} in groundwater hydraulically upgradient of the PRB to values <1 {micro}g L{sup -1} in groundwater within and hydraulically downgradient of the PRB. Chromium removal from groundwater occurs at the leading edge of the PRB and also within the aquifer immediately upgradient of the PRB. These regions also witness the greatest amount of secondary mineral formation due to steep geochemical gradients that result from the corrosion of zerovalent iron. X-ray absorption near-edge structure (XANES) spectroscopy indicated that chromium is predominantly in the trivalent oxidation state, confirming that reductive processes are responsible for Cr sequestration. XANES spectra and microscopy results suggest that Cr is, in part, associated with iron sulfide grains formed as a consequence of microbially mediated sulfate reduction in and around the PRB. Results of this study provide evidence that secondary iron-bearing mineral products may enhance the capacity of zerovalent iron systems to remediate Cr in groundwater, either through redox reactions at the mineral-water interface or by the release of Fe(II) to solution via mineral dissolution and/or metal corrosion.

  7. Reactive Di racting Trees Giovanni Della-Libera

    E-Print Network [OSTI]

    Lynch, Nancy

    . Their empirical performance under heavy load surpasses all other shared counter implementations. However, di for better performance at high loads. The software combining methods 11 33 34] have the advantage.I.T. A shared counter is a concurrent object that provides a fetch-and-increment operation in a dis- tributed

  8. Optimal operation of large-scale power systems

    SciTech Connect (OSTI)

    Lee, K.Y.; Ortiz, J.L.; Mohtadi, M.A.; Park, Y.M.

    1988-05-01T23:59:59.000Z

    This paper presents a method for an optimal operation of large-scale power systems similar to the one utilized by the Houston Lighting and Power Company. The main objective is to minimize the system fuel costs, and maintain an acceptable system performance in terms of limits on generator real and reactive power outputs, transformer tap settings, and bus voltage levels. Minimizing the fuel costs of such large-scale systems enhances the performance of optimal real power generator allocation and of optimal power flow that results in an economic dispatch. The gradient projection method (GPM) is utilized in solving the optimization problems. It is an iterative numerical procedure for finding an extremum of a function of several variables that are required to satisfy various constraining relations without using penalty functions or Lagrange multipliers among other advantages. Mathematical models are developed to represent the sensitivity relationships between dependent and control variables for both real- and reactive-power optimization procedures; and thus eliminate the use of B-coefficients. Data provided by the Houston lighting and Power Company are used to demonstrate the effectiveness of the proposed procedures.

  9. Reactive trace metals in the stratified central North Pacific

    SciTech Connect (OSTI)

    Bruland, K.W. (Univ. of California, Santa Cruz, CA (United States)); Orians, K.J. (Univ. of British Columbia, Vancouver (Canada)); Cowen, J.P. (Univ. of Hawaii, Manoa, HI (United States))

    1994-08-01T23:59:59.000Z

    Vertical concentration profiles of the dissolved and suspended particulate phases were determined for a suite of reactive trace metals, Al, Fe, Mn, Zn, and Cd, during summertime at a station in the center of the North Pacific gyre. During summer the euphotic zone becomes stratified, forming a shallow (0-25 m), oligotrophic, mixed layer overlying a subsurface (25-140 m), strongly-stratified region. The physical, biological, and chemical structure within the euphotic zone during this period enhanced the effect of atmospheric inputs of Al, Fe, and Mn on mixed layer concentrations. For example, the concentration of dissolved Fe in the surface mixed layer was eighteen times that observed at a depth of 100 m. The observed aeolian signature of these metals matched that predicted from estimates of atmospheric input during the period between the onset of stratification and sampling. The distributions of suspended particulate Al, Fe, and Mn all exhibited minima in the euphotic zone and increased with depth into the main thermocline. Particulate Al and Fe were then uniform with depth below 1000 m before increasing in the near bottom nepheloid layer. Average particulate phase concentrations in intermediate and deep waters of the central North Pacific were 1.0, 0.31, and 0.055 nmol[center dot]kg[sup [minus]1] for Al, Fe, and Mn, respectively. The distribution of particulate Cd exhibited a maximum within the subsurface euphotic zone. Particulate zinc also exhibited a surface maximum, albeit a smaller one. Concentrations of particulate Zn and Cd in intermediate and deep waters were 17 and 0.2 pmol[center dot]kg[sup [minus]1]. Substantial interbasin differences in particulate trace metals occur. Concentrations of suspended particulate Al, Fe, and Mn were three to four times lower in the central North Pacific than recently reported for the central North Atlantic gyre, consistent with differences in atmospheric input to these two regions.

  10. Kinetics and mechanisms of reactions involving small aromatic reactive intermediates

    SciTech Connect (OSTI)

    Lin, M.C. [Emory Univ., Atlanta, GA (United States)

    1993-12-01T23:59:59.000Z

    Small aromatic radicals such as C{sub 6}H{sub 5}, C{sub 6}H{sub 5}O and C{sub 6}H{sub 4} are key prototype species of their homologs. C{sub 6}H{sub 5} and its oxidation product, C{sub 6}H{sub 5}O are believed to be important intermediates which play a pivotal role in hydrocarbon combustion, particularly with regard to soot formation. Despite their fundamental importance, experimental data on the reaction mechanisms and reactivities of these species are very limited. For C{sub 6}H{sub 5}, most kinetic data except its reactions with NO and NO{sub 2}, were obtained by relative rate measurements. For C{sub 6}H{sub 5}O, the authors have earlier measured its fragmentation reaction producing C{sub 5}H{sub 5} + CO in shock waves. For C{sub 6}H{sub 4}, the only rate constant measured in the gas phase is its recombination rate at room temperature. The authors have proposed to investigate systematically the kinetics and mechanisms of this important class of molecules using two parallel laser diagnostic techniques--laser resonance absorption (LRA) and resonance enhanced multiphoton ionization mass spectrometry (REMPI/MS). In the past two years, study has been focused on the development of a new multipass adsorption technique--the {open_quotes}cavity-ring-down{close_quotes} technique for kinetic applications. The preliminary results of this study appear to be quite good and the sensitivity of the technique is at least comparable to that of the laser-induced fluorescence method.

  11. Psychophysiological Reactivity to Self and Model Images in an Upward Social Comparison Manipulation

    E-Print Network [OSTI]

    Tamez, Jeannine

    2012-02-14T23:59:59.000Z

    The current study examined affective reactivity to oneself in an upward socialcomparison manipulation using autonomic physiological responses. Study I was conducted to select images of thin and average size models used to elicit a social comparison...

  12. Assessment of the Economic Potential of Microgrids for Reactive Power Supply

    SciTech Connect (OSTI)

    Appen, Jan von; Marnay, Chris; Stadler, Michael; Momber, Ilan; Klapp, David; Scheven, Alexander von

    2011-05-01T23:59:59.000Z

    As power generation from variable distributed energy resources (DER) grows, energy flows in the network are changing, increasing the requirements for ancillary services, including voltage support. With the appropriate power converter, DER can provide ancillary services such as frequency control and voltage support. This paper outlines the economic potential of DERs coordinated in a microgrid to provide reactive power and voltage support at its point of common coupling. The DER Customer Adoption Model assesses the costs of providing reactive power, given local utility rules. Depending on the installed DER, the cost minimizing solution for supplying reactive power locally is chosen. Costs include the variable cost of the additional losses and the investment cost of appropriately over-sizing converters or purchasing capacitors. A case study of a large health care building in San Francisco is used to evaluate different revenue possibilities of creating an incentive for microgrids to provide reactive power.

  13. Reactive ion etching: Optimized diamond membrane fabrication for transmission electron microscopy

    E-Print Network [OSTI]

    Li, Luozhou

    Commonly used preparation method for thin diamond membranes by focused ion beam (FIB) techniques results in surface damage. Here, the authors introduce an alternative method based on reactive ion etching (RIE). To compare ...

  14. Reactivity of Ozone with Solid Potassium Iodide Investigated by Atomic Force Microscopy

    E-Print Network [OSTI]

    Brown, Matthew A.

    2008-01-01T23:59:59.000Z

    J. C. , Reactivity of ozone on solid potassium iodide.and mechanisms of aqueous ozone reactions with bromide,for Dry Deposition of Ozone to Seawater Surfaces. Journal of

  15. Origin of Support Effects on the Reactivity of a Ceria Cluster...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the effects of supports on the reactivity of Ce2O4 cluster were probed by the adsorption of CO2 and CO. The acidic CO2 molecule chemisorbs at the O sites of the cluster,...

  16. On the Evolution of Reactive Components A Process-Algebraic Approach

    E-Print Network [OSTI]

    Müller-Olm, Markus

    On the Evolution of Reactive Components ­ A Process-Algebraic Approach ­ Markus M¨uller-Olm1 1999 #12;162 Markus M¨uller-Olm, Bernhard Steffen, and Rance Cleaveland in out in out overflow in out

  17. Combining thorium with burnable poison for reactivity control of a very long cycle BWR

    E-Print Network [OSTI]

    Inoue, Yuichiro, 1969-

    2004-01-01T23:59:59.000Z

    The effect of utilizing thorium together with gadolinium, erbium, or boron burnable absorber in BWR fuel assemblies for very long cycle is investigated. Nuclear characteristics such as reactivity and power distributions ...

  18. Leaching of Metals from Fly ash-Amended Permeable Reactive Barriers Doina L. Morar 1

    E-Print Network [OSTI]

    Aydilek, Ahmet

    (Petzrick 2001). Unfortunately, this HCC fly ash cannot be beneficially reused in the construction industry organic and inorganic pollutants. Specific reactive materials such as wood chips, limestone, manure (USEPA

  19. Phase II: Performance Evaluation of Permeable Reactive Barriers and Potential for Rejuvenation by Chemical Flushing

    Broader source: Energy.gov [DOE]

    Final ReportPhase II: Performance Evaluation of Permeable Reactive Barriers and Potential for Rejuvenation by Chemical FlushingU. S. Environmental Protection Agency Region 8 SupportJanuary 2004

  20. Influence of calcite on uranium(VI) reactive transport in the groundwater–river mixing zone

    SciTech Connect (OSTI)

    Ma, Rui; Liu, Chongxuan; Greskowiak, Janek; Prommer, Henning; Zachara, John M.; Zheng, Chunmiao

    2014-01-23T23:59:59.000Z

    Calcite is an important mineral that can affect uranyl reactive transport in subsurface sediments. This study investigated the distribution of calcite and its influence on uranyl adsorption and reactive transport in the groundwater-river mixing zone at US Hanford 300A, Washington State. Simulations using a 2D reactive transport model under field-relevant hydrogeochemical conditions revealed a complex distribution of calcite concentration as a result of dynamic groundwater-river interactions. The calcite concentration distribution in turn affected the spatial and temporal changes in aqueous carbonate, calcium, and pH, which subsequently influenced U(VI) mobility and discharge rates into the river. The results implied that calcite distribution and its concentration dynamics is an important consideration for field characterization, monitoring, and reactive transport prediction.

  1. Reactive Transport Modeling of Natural Attenuation in Stormwater Bioretention Cells and Under Land Application of Wastewater 

    E-Print Network [OSTI]

    Zhang, Jingqiu

    2014-04-29T23:59:59.000Z

    hydrocarbon, nutrient, metals, and solids. Vegetation also plays an important role in reducing water volume, and removing nutrients and solutes from the contaminated soil. We used a reactive transport model MIN3P-THM to simulate the natural attenuation...

  2. Molten salt extraction of transuranic and reactive fission products from used uranium oxide fuel

    DOE Patents [OSTI]

    Herrmann, Steven Douglas

    2014-05-27T23:59:59.000Z

    Used uranium oxide fuel is detoxified by extracting transuranic and reactive fission products into molten salt. By contacting declad and crushed used uranium oxide fuel with a molten halide salt containing a minor fraction of the respective uranium trihalide, transuranic and reactive fission products partition from the fuel to the molten salt phase, while uranium oxide and non-reactive, or noble metal, fission products remain in an insoluble solid phase. The salt is then separated from the fuel via draining and distillation. By this method, the bulk of the decay heat, fission poisoning capacity, and radiotoxicity are removed from the used fuel. The remaining radioactivity from the noble metal fission products in the detoxified fuel is primarily limited to soft beta emitters. The extracted transuranic and reactive fission products are amenable to existing technologies for group uranium/transuranic product recovery and fission product immobilization in engineered waste forms.

  3. Distributed control of reactive power flow in a radial distribution circuit with high photovoltaic penetration

    E-Print Network [OSTI]

    Turitsyn, Konstantin; Backhaus, Scott; Chertkov, Michael

    2009-01-01T23:59:59.000Z

    We show how distributed control of reactive power can serve to regulate voltage and minimize resistive losses in a distribution circuit that includes a significant level of photovoltaic (PV) generation. To demonstrate the technique, we consider a radial distribution circuit with a single branch consisting of sequentially-arranged residential-scale loads that consume both real and reactive power. In parallel, some loads also have PV generation capability. We postulate that the inverters associated with each PV system are also capable of limited reactive power generation or consumption, and we seek to find the optimal dispatch of each inverter's reactive power to both maintain the voltage within an acceptable range and minimize the resistive losses over the entire circuit. We assume the complex impedance of the distribution circuit links and the instantaneous load and PV generation at each load are known. We compare the results of the optimal dispatch with a suboptimal local scheme that does not require any com...

  4. Photochemical Transformation of Carboxylated Multiwalled Carbon Nanotubes: Role of Reactive Oxygen Species

    E-Print Network [OSTI]

    Alvarez, Pedro J.

    in consumer and industrial products (e.g., electronics, composite materials, and sporting equipment) mayPhotochemical Transformation of Carboxylated Multiwalled Carbon Nanotubes: Role of Reactive Oxygen investigated the photochemical transformation of carboxylated multiwalled carbon nanotubes (COOH

  5. Reactive Ballistic Deposition of Porous TiO2 Films: Growth and...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    high-surface area films of TiO2 are synthesized by reactive ballistic deposition of titanium metal in an oxygen ambient. Auger electron spectroscopy (AES) is used to investigate...

  6. S-nitrosothiols and reactive oxygen species in plant disease resistance and development 

    E-Print Network [OSTI]

    Brzezek, Kerstin

    2014-06-28T23:59:59.000Z

    Nitric oxide (NO) as well as reactive oxygen species (ROS) play an important role in defence signalling in plants. After successful recognition of an invading pathogen, an increase in ROS occurs, the ’oxidative burst’; ...

  7. Prediction of concentrations of reactive nitrogen species in aqueous solutions and cells

    E-Print Network [OSTI]

    Lim, ChangHoon, Ph. D. Massachusetts Institute of Technology

    2011-01-01T23:59:59.000Z

    Reactive nitrogen species (RNS) derived from nitric oxide (NO) have been implicated in cancer and other diseases, but their intracellular concentrations are largely unknown. To estimate them under steady-state conditions ...

  8. FLOW AND REACTIVE TRANSPORT IN POROUS MEDIA INDUCED BY WELL INJECTION: SIMILARITY SOLUTION

    E-Print Network [OSTI]

    FLOW AND REACTIVE TRANSPORT IN POROUS MEDIA INDUCED BY WELL INJECTION: SIMILARITY SOLUTION C.J. VAN from laboratory batch experiments. Typical examples of isotherms are (see e.g. Freeze and Cherry [FC

  9. DYNAMIC MODELING AND CONTROL OF REACTIVE DISTILLATION FOR HYDROGENATION OF BENZENE 

    E-Print Network [OSTI]

    Aluko, Obanifemi

    2010-01-16T23:59:59.000Z

    This work presents a modeling and control study of a reactive distillation column used for hydrogenation of benzene. A steady state and a dynamic model have been developed to investigate control structures for the column. The most important aspects...

  10. Declarative Goals in Reactive Plans \\Lambda Michael Beetz and Drew McDermott

    E-Print Network [OSTI]

    McDermott, Drew V.

    Declarative Goals in Reactive Plans \\Lambda Michael Beetz and Drew McDermott Yale University, Department of Computer Science P.O. Box 2158, Yale Station New Haven, CT 06520 beetz@cs.yale.edu, mcdermott

  11. Hall mobility of cuprous oxide thin films deposited by reactive direct-current magnetron sputtering

    E-Print Network [OSTI]

    Lee, Yun Seog

    Cuprous oxide (Cu[subscript 2]O) is a promising earth-abundant semiconductor for photovoltaic applications. We report Hall mobilities of polycrystalline Cu[subscript 2]O thin films deposited by reactive dc magnetron ...

  12. Inhibition of Pyruvate Kinase M2 by Reactive Oxygen Species Contributes to Cellular Antioxidant Responses

    E-Print Network [OSTI]

    Vander Heiden, Matthew G.

    Control of intracellular reactive oxygen species (ROS) concentrations is critical for cancer cell survival. We show that, in human lung cancer cells, acute increases in intracellular concentrations of ROS caused inhibition ...

  13. Reactivity of nanocolloidal particles -Fe2O3 at charged interfaces: 2-Electrochemical conversion.

    E-Print Network [OSTI]

    Boyer, Edmond

    synthesis of magnetic and conductive liquids. The reactivity of charged colloidal10 particles occurs in two by methyl viologen), nanoparticles of hematite and goethite (-FeOOH: d = 50 nm) are invo

  14. Social comparison test using women's subjective and physiological reactivity to thin and average size models

    E-Print Network [OSTI]

    Tamez, Jeannine Paola

    2009-05-15T23:59:59.000Z

    The current study examined the subjective and physiological reactivity to body image stimuli among females engaging in a social comparison task. Study I was conducted to select images of thin and average size models and neutral objects for Study...

  15. RH Packaging Operations Manual

    SciTech Connect (OSTI)

    Washington TRU Solutions LLC

    2003-09-17T23:59:59.000Z

    This procedure provides operating instructions for the RH-TRU 72-B Road Cask, Waste Shipping Package. In this document, ''Packaging'' refers to the assembly of components necessary to ensure compliance with the packaging requirements (not loaded with a payload). ''Package'' refers to a Type B packaging that, with its radioactive contents, is designed to retain the integrity of its containment and shielding when subject to the normal conditions of transport and hypothetical accident test conditions set forth in 10 CFR Part 71. Loading of the RH 72-B cask can be done two ways, on the RH cask trailer in the vertical position or by removing the cask from the trailer and loading it in a facility designed for remote-handling (RH). Before loading the 72-B cask, loading procedures and changes to the loading procedures for the 72-B cask must be sent to CBFO at sitedocuments@wipp.ws for approval.

  16. Gulf operations still recovering

    SciTech Connect (OSTI)

    Koen, A.D.

    1992-09-21T23:59:59.000Z

    This paper reports that reports of damage caused by Hurricane Andrew were leveling off last week at the U.S. Minerals Management Service as Gulf of Mexico operators pressed ahead with repairs. The hurricane struck South Florida Aug. 4, churned west into the gulf, then swung north and hit the South Louisiana coast Aug. 5. By the close of business Sept. 8 MMS had received damage reports covering 83 pipeline segments and 193 platforms and satellite installations. MMS last week estimated about 500 MMcfd of gas production had been restored in the gulf and 100,000-150,000 b/d of oil. Production still lost as a result of Andrew was estimated at 2-2.5 bcfd of gas and 90,000-120 b/d of oil. MMS estimates Gulf of Mexico wells before the storm were producing about 12.5-13 bcfd of gas and 750,000 b/d of oil.

  17. Gulf operators resuming production

    SciTech Connect (OSTI)

    Koen, A.D.

    1992-09-14T23:59:59.000Z

    This paper reports that Gulf of Mexico operators last week were gradually restoring production at installations struck by Hurricane Andrew. The Minerals Management Service continued receiving reports of more damage. By the end of the day Sept. 8, MMS had received reports of damage to 83 pipeline segments and 193 platforms and satellite installations. Damage reports listed 112 installations with structural damage, 13 platforms toppled and five leaning, and 30 satellite platforms toppled and 33 leaning. But despite the extent of damage the storm inflicted on oil and gas installations in the gulf, it pales in comparison to the misery and suffering the storm caused in Florida and Louisiana, an oil company official said.

  18. FRMAC Operations Manual

    SciTech Connect (OSTI)

    Frandsen, K.

    2010-05-01T23:59:59.000Z

    In the event of a major radiological incident, the Federal Radiological Monitoring and Assessment Center (FRMAC) will coordinate the federal agencies that have various statutory responsibilities. The FRMAC is responsible for coordinating all environmental radiological monitoring, sampling, and assessment activities for the response. This manual describes the FRMAC’s response activities in a radiological incident. It also outlines how FRMAC fits in the National Incident Management System (NIMS) under the National Response Framework (NRF) and describes the federal assets and subsequent operational activities which provide federal radiological monitoring and assessment of the affected areas. In the event of a potential or existing major radiological incident, the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) is responsible for establishing and managing the FRMAC during the initial phases.

  19. DOE Corporate Operating Experience Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-04-08T23:59:59.000Z

    The Order institutes a DOE wide program for the management of operating experience to prevent adverse operating incidents and facilitate the sharing of good work practices among DOE sites. Cancels DOE O 210.2.

  20. TACTICAL RADIO OPERATIONS August 2009

    E-Print Network [OSTI]

    US Army Corps of Engineers

    FM 6-02.53 TACTICAL RADIO OPERATIONS August 2009 DISTRIBUTION RESTRICTION. Approved for public August 2009 TACTICAL RADIO OPERATIONS Contents Page PREFACE ...........................................................................................................viii Chapter 1 APPLICATIONS FOR TACTICAL RADIO DEPLOYMENT.............................. 1-1 Modularity

  1. Operating Efficiency Comes From Teamwork

    E-Print Network [OSTI]

    Relyea, D. L.; Stone, A.

    A group of operating and planning personnel formed the INter Plant Utilities Team [INPUT] to improve energy efficiency and reliability for Exxon's Baytown, Texas, refinery and chemical plants complex. The Team coordinates the day-to-day operations...

  2. A slightly edited version of this paper appears in Proc. 1998 Conf on Foundations of Computer-Aided Process Operations [FOCAPO

    E-Print Network [OSTI]

    Krebsbach, Kurt D.

    -Aided Process Operations [FOCAPO] Applying a Procedural and Reactive Approach to Abnormal Situations in Re nery explosion at a petrochemical plant in 1989. This accident represents an extreme case within the spectrum of major process disruptions, collectively referred to as abnormal situations. While most abnor- mal

  3. Conditioned changes in pain reactivity: conditioned stimuli elicit hypoalgesia under a wide range of test conditions

    E-Print Network [OSTI]

    Illich, Paul Anthony

    1990-01-01T23:59:59.000Z

    conditioned hypoalgesia, two recent reports suggest that a conditioned stimulus (CS) which has been paired with an aversive event may sometimes produce an increase in pain reactivity, or "hyperalgesia" rather than hypoalgesia (Davis & Henderson, 1985...-Evans hooded rats) (Davis & Henderson, 1985; Lysle & Fowler, 1988). Currently, it is not clear what determines whether a stimulus which has been paired with an aversive event will elicit either an increase or decrease in pain reactivity. In the present...

  4. Direct conversion of carboxylate salts to carboxylic acids via reactive extraction

    E-Print Network [OSTI]

    Xu, Xin

    2008-10-10T23:59:59.000Z

    DIRECT CONVERSION OF CARBOXYLATE SALTS TO CARBOXYLIC ACIDS VIA REACTIVE EXTRACTION A Thesis by XIN XU Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE August 2008 Major Subject: Chemical Engineering DIRECT CONVERSION OF CARBOXYLATE SALTS TO CARBOXYLIC ACIDS VIA REACTIVE EXTRACTION A Thesis by XIN XU Submitted to the Office of Graduate Studies...

  5. Considerations for absorber analysis by reactivity measurements in a nuclear reactor

    E-Print Network [OSTI]

    Kaufman, Jay Leslie

    1959-01-01T23:59:59.000Z

    CONSIUERATIONS FOR ASSOESER ANALYSIS bY REACTIVITY NEASURENENTS IN A NUCLEAR REACTOR JAY LESLXE EAUFNAN Submitted to the Graduate School of tha Agricultural and Mechanical College of Texas in partial fulfillment of the requirements... for the degree of NASTER OF SCIENCE August 1959 Ma)or Sub)ect t Fhysics CONSIDERATIONS POR ABSORBER ANALYSIS BY REACTIVITY MEASUREHENTS IN A NUCLEAR REACTOR A Thssia By JA. Y LESLLE EAUPNAN Approved as to style and content by: (Chainsan of Coenittss...

  6. STANDARD OPERATING PROCEDURES Site Selection

    E-Print Network [OSTI]

    Fischer, Emily V.

    IMPROVE STANDARD OPERATING PROCEDURES SOP 126 Site Selection Date Last Modified Modified by: 09 References none #12;SOP 126: Site Selection 3 1.0 PURPOSE AND APPLICABILITY This standard operating procedure field conditions, and for ease of operation and maintenance. IMPROVE aerosol samplers are generally

  7. ENERGY MANAGEMENT OPERATIONAL PROCEDURE MANUAL

    E-Print Network [OSTI]

    Harman, Neal.A.

    ENERGY MANAGEMENT OPERATIONAL PROCEDURE MANUAL Swansea University Estates Services Singleton Park Swansea SA2 8PP Tel 01792 295819 Fax 01792 295820 #12;Swansea University Energy Management Operational ......................................................................................11 #12;Swansea University Energy Management Operational Procedural Manual Estates Services April 2008

  8. Operating Reserves and Variable Generation

    SciTech Connect (OSTI)

    Ela, E.; Milligan, M.; Kirby, B.

    2011-08-01T23:59:59.000Z

    This report tries to first generalize the requirements of the power system as it relates to the needs of operating reserves. It also includes a survey of operating reserves and how they are managed internationally in system operations today and then how new studies and research are proposing they may be managed in the future with higher penetrations of variable generation.

  9. Liens for Oil and Gas Operations (Nebraska)

    Broader source: Energy.gov [DOE]

    This section contains regulations concerning lien allowances made to operators of oil and gas operations.

  10. The higher spin Laplace operator

    E-Print Network [OSTI]

    Hendrik De Bie; David Eelbode; Matthias Roels

    2015-01-24T23:59:59.000Z

    This paper deals with a certain class of second-order conformally invariant operators acting on functions taking values in particular (finite-dimensional) irreducible representations of the orthogonal group. These operators can be seen as a generalisation of the Laplace operator to higher spin as well as a second order analogue of the Rarita-Schwinger operator. To construct these operators, we will use the framework of Clifford analysis, a multivariate function theory in which arbitrary irreducible representations for the orthogonal group can be realised in terms of polynomials satisfying a system of differential equations. As a consequence, the functions on which this particular class of operators act are functions taking values in the space of harmonics homogeneous of degree k. We prove the ellipticity of these operators and use this to investigate their kernel, focusing on both polynomial solutions and the fundamental solution.

  11. Application of a data assimilation method via an ensemble Kalman filter to reactive urea hydrolysis transport modeling

    SciTech Connect (OSTI)

    Juxiu Tong; Bill X. Hu; Hai Huang; Luanjin Guo; Jinzhong Yang

    2014-03-01T23:59:59.000Z

    With growing importance of water resources in the world, remediations of anthropogenic contaminations due to reactive solute transport become even more important. A good understanding of reactive rate parameters such as kinetic parameters is the key to accurately predicting reactive solute transport processes and designing corresponding remediation schemes. For modeling reactive solute transport, it is very difficult to estimate chemical reaction rate parameters due to complex processes of chemical reactions and limited available data. To find a method to get the reactive rate parameters for the reactive urea hydrolysis transport modeling and obtain more accurate prediction for the chemical concentrations, we developed a data assimilation method based on an ensemble Kalman filter (EnKF) method to calibrate reactive rate parameters for modeling urea hydrolysis transport in a synthetic one-dimensional column at laboratory scale and to update modeling prediction. We applied a constrained EnKF method to pose constraints to the updated reactive rate parameters and the predicted solute concentrations based on their physical meanings after the data assimilation calibration. From the study results we concluded that we could efficiently improve the chemical reactive rate parameters with the data assimilation method via the EnKF, and at the same time we could improve solute concentration prediction. The more data we assimilated, the more accurate the reactive rate parameters and concentration prediction. The filter divergence problem was also solved in this study.

  12. Enhanced Building Operation Using "Operation Diagnostics" - A Case Study 

    E-Print Network [OSTI]

    Baumann, O.

    2005-01-01T23:59:59.000Z

    ICEBO International Conference for Enhanced Building Operations October 11-13, 2005, Pittsburgh, PA, USA Enhanced Building Operation Using ‘Operation Diagnostics’ – A Case Study Dipl.-Ing. Oliver Baumann Division for Building and System...- ing function implemented in the used visualization tool Pia [4] that enables to select and highlight data interactively in the diagram. Subsequently, numerical analysis gives the possibility to estimate optimization and saving potential...

  13. Treatability Study Operational Testing Program and Implementation Plan for the Gunite and Associated Tanks at the Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    NONE

    1996-09-01T23:59:59.000Z

    To support future decision making of the Gunite and Associated Tanks (GAAT) Operable Unit (OU) remedy selection, the Department of Energy (DOE) is performing a Treatability Study (TS), consistent with the EPA guidance for Comprehensive Environmental Response, compensation, and Liability Act (CERCLA) treatability studies. The study will inform stakeholders about various waste removal technologies and the cost of potential remediation approaches, particularly the cost associated with sluicing and the reduction in risk to human health and the environment from tank content removal. As part of the GAAT OU remedy, a series of studies and technology tests will be preformed. These may address one or more of the following areas, characterization, removal, treatment, and transfer of wastes stored in the GAAT OU.

  14. ORISE: REAC/TS Radiation Accident Registries

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Accident Registries The Radiation Emergency Assistance CenterTraining Site (REACTS) at the Oak Ridge Institute for Science and Education (ORISE) maintains a number of radiation...

  15. ORISE: REAC/TS Radiation Treatment Medications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Treatment Medications The Radiation Emergency Assistance CenterTraining Site (REACTS) is a valuable resource in the use of drug therapies to treat radiation exposure. REACTS...

  16. Do's & Don'ts Manatee County

    E-Print Network [OSTI]

    Jawitz, James W.

    company Do they.... Display the required Best Management Practices Training Certification Decal from the roadway, storm drain, and ditches? Maintain a fertilizer-free zone 10 feet from top of bank around water bodies and wetlands? For more information please contact us at: MANATEE COUNTY Division

  17. Enron Documen'ts I.1

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011 Strategic Plan Departmentof EnergyPublic LawEnergyEnhanced ReduceofEnrico

  18. REAC/TS | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved: 5-13-14 FEDERALAmerica TreatyWastewantsRequests| National

  19. TS Wind Power Developers | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2,AUDITCalifornia Sector:Shrenik IndustriesState ofSwitchpowerTCITMETS Wind

  20. ORISE: REAC/TS Cytogenetic Biodosimetry

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)Integrated CodesTransparencyDOENurse Triage LinesCytogenetic Biodosimetry Cytogenetic