National Library of Energy BETA

Sample records for rate binder kelly

  1. Henry Kelly

    Office of Energy Efficiency and Renewable Energy (EERE)

    Dr. Henry Kelly is Senior Advisor to the Director of EPSA. He previously served as Principal Associate Director for Environment and Energy in the White House Office of Science and Technology Policy...

  2. Constitutive response of two plastic-bonded explosive binder materials as a function of temperature and strain-rate

    SciTech Connect (OSTI)

    Cady, C. M.; Blumenthal, W. R.; Gray, G. T. , III; Idar, D. J.

    2004-01-01

    Recently, interest has been shown concerning the mechanical response of plastic-bonded explosives (PBX) and propellants to enable the development of predictive materials models describing the mechanical behavior of these composites. Accordingly, detailed information about the constitutive response is crucial. Compression measurements were conducted on two explosive formulation binders, extruded Estane{trademark} 5703 (hereafter referred to as Estane) and plasticized Estane as a function of temperature from -60 C to +23 C using a specially-designed split Hopkinson pressure bar (strain rate of {approx} 2800 s{sup -1}) and quasi-stattically (strain rates from {approx} 0.001 to 1 s{sup -1}) using a hydraulic load frame. The mechanical response of the Estane was found to exhibit a stronger dependency on strain rate and temperature and higher flow strength for similar test conditions of the materials tested. Plasticized Estane was less sensitively dependent on strain rate and temperature. The visco-elastic recovery of both binders is seen to dominate the mechanical behavior at temperatures above the glass transition temperature (T{sub g}). The binders exhibited increasing elastic loading moduli, E, with increasing strain rate or decreasing temperature, which is similar to other polymeric materials. There is a pronounced shift in the apparent T{sub g} to higher temperatures as the strain rate is increased. At low strain rates the binders exhibit a yield behavior followed by a drop in the flow stress which may or may not recover. At high strain rates the load drop does not occur and the flow stresses level out. A discussion of the Hopkinson bar technique as applied to polymeric or low impedance materials is described in detail.

  3. Kelly Gonzalez

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesse Bergkamp Graduate student Subtask 4Photo4 |KathyKatrinaKeith HardyKelly

  4. CURRICULUM VITAE Kelly T. Morgan

    E-Print Network [OSTI]

    Ma, Lena

    ) soil nutrient movement with irrigation and rain water, 2) nutrient transformation rates, 3) cropCURRICULUM VITAE Kelly T. Morgan Associate Professor, Soil and Water Science University of Florida of Florida Plant Pathology MS 1982 University of Florida Soil & Water Science PhD 2004 Research

  5. Laboratory development of fourth generation sulphlex binders 

    E-Print Network [OSTI]

    Menon, Vivek Narayan

    1994-01-01

    of relative rate of thermal stress relaxation 95 13 Uniaxial compressive creep results at 104"F for the binders tested under this program 97 14 Unconfined compressive stress and strain at failure for the binders tested at 104'F and a strain rate of 0. 15... Strength Unconf. Compressive Strength Compressive Strength indirect Tensile Failure Test Tensile Stress S. Strain at Failure AASHTO T-165, T-167 Ref. 12 and Ref. 22 TABLE 4 Summary of the distress mechanisms and associated testing procedures of mixtures...

  6. NREL: Energy Analysis - Kelly Eurek

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass map shines light on771/6/14 Contact:NewsWebmasterWorkingEllaKruegerKathleen NawazKelly

  7. Kelly Hot Spring Geothermal Project: Kelly Hot Spring Agricultural Center preliminary design. Final technical report

    SciTech Connect (OSTI)

    Longyear, A.B. (ed.)

    1980-08-01

    A Phase 1 Preliminary Design, Construction Planning and Economic Analysis has been conducted for the Kelly Hot Spring Agricultural Center in Modoc County, California. The core activity is a 1360 breeding sow, swine raising complex that utilizes direct heat energy from the Kelly Hot Spring geothermal resource. The swine is to be a totally confined operation for producing premium pork in controlled-environment facilities. The complex contains a feed mill, swine raising buildings and a complete waste management facility that produces methane gas to be delivered to a utility company for the production of electricity. The complex produces 6.7 million pounds of live pork (29,353 animals) shipped to slaughter per year; 105,000 cu. ft. of scrubbed methane per day; and fertilizer. Total effluent is less than 200 gpm of agricultural quality-water with full odor control. The methane production rate made possible with geothermal direct heat is equivalent to at least 400 kw continuous. Sale of the methane on a co-generation basis is being discussed with the utility company. The use of geothermal direct heat energy in the complex displaces nearly 350,000 gallons of fuel oil per year. Generation of the biogas displaces an additional 300,000 gallons of fuel oil per year.

  8. John E. Kelly | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dr. Kelly received his B.S. in nuclear engineering from the University of Michigan in 1976 and his Ph.D. in nuclear engineering from the Massachusetts Institute of Technology in...

  9. Viscoelastic models for explosive binder materials

    SciTech Connect (OSTI)

    Bardenhagen, S.G.; Harstad, E.N.; Maudlin, P.J.; Gray, G.T. [Los Alamos National Lab., NM (United States); Foster, J.C. Jr. [Wright Lab., Eglin AFB, FL (United States)

    1997-07-01

    An improved model of the mechanical properties of the explosive contained in conventional munitions is needed to accurately simulate performance and accident scenarios in weapons storage facilities. A specific class of explosives can he idealized as a mixture of two components: energetic crystals randomly suspended in a polymeric matrix (binder). Strength characteristics of each component material are important in the macroscopic behavior of the composite (explosive). Of interest here is the determination of an appropriate constitutive law for a polyurethane binder material. This paper is a continuation of previous work in modeling polyurethane at moderately high strain rates and for large deformations. Simulation of a large deformation (strains in excess of 100%) Taylor Anvil experiment revealed numerical difficulties which have been addressed. Additional experimental data have been obtained including improved resolution Taylor Anvil data, and stress relaxation data at various strain rates. A thorough evaluation of the candidate viscoelastic constitutive model is made and possible improvements discussed.

  10. Nanoscale Heterostructures and Thermoplastic Resin Binders: Novel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Nanoscale Heterostructures and Thermoplastic Resin Binders: Novel Lithium-Ion Anodes Nanoscale Heterostructures and Thermoplastic Resin Binders: Novel Lithium-Ion Anodes 2012 DOE...

  11. Novel Binders and Methods for Agglomeration of Ore

    SciTech Connect (OSTI)

    S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

    2006-12-31

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking. This project has identified several acid-resistant binders and agglomeration procedures that can be used for improving the energy efficiency of heap leaching, by preventing the ''ponding'' and ''channeling'' effects that currently cause reduced recovery and extended leaching cycle times. Methods have also been developed for iron ore processing which are intended to improve the performance of pellet binders, and have directly saved energy by increasing filtration rates of the pelletization feed by as much as 23%.

  12. EProf: An Energy Profiler for the iPAQ Kelly Koskelin

    E-Print Network [OSTI]

    and future work 35 7 #12;8 #12;List of Figures 3-1 Energy allocation. The instruction sampling rateEProf: An Energy Profiler for the iPAQ by Kelly Koskelin Submitted to the Department of Electrical of Engineering in Computer Science and Engineering at the MASSACHUSETTS INSTITUTE OF TECHNOLOGY February 2004 c

  13. Compositional evaluation of asphalt binder recycling agents 

    E-Print Network [OSTI]

    Madrid, Richard Charles

    1997-01-01

    new asphalt binder. The high temperature Superpave TM Performance Grade (PG) specifications for recycled asphalt binders were found to be highly dependent on the aged asphalt. In addition, as the amount of saturates in the aromatic recycling agent...

  14. Electrochemical components employing polysiloxane-derived binders

    DOE Patents [OSTI]

    Delnick, Frank M.

    2013-06-11

    A processed polysiloxane resin binder for use in electrochemical components and the method for fabricating components with the binder. The binder comprises processed polysiloxane resin that is partially oxidized and retains some of its methyl groups following partial oxidation. The binder is suitable for use in electrodes of various types, separators in electrochemical devices, primary lithium batteries, electrolytic capacitors, electrochemical capacitors, fuel cells and sensors.

  15. Data and innovation: the case for experimentation Frank Kelly

    E-Print Network [OSTI]

    Kelly, Frank

    Data and innovation: the case for experimentation Frank Kelly Professor Frank Kelly FRS is Chief applications. The ability to produce innovative data applications is no longer the preserve of computer a highly controlled development from concept to finished product, towards a more iterative approach where

  16. Women @ Energy: Kelly Lively | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergyThe U.S.Lacledeutilities.Energy ThefullAssociateJenniferCarradoKelly Lively has

  17. California: Conducting Polymer Binder Boosts Storage Capacity...

    Broader source: Energy.gov (indexed) [DOE]

    Nextval, Inc., Lawrence Berkeley National Laboratory (LBNL) developed a Conducting Polymer Binder for high-capacity lithium-ion batteries. With a focus on enabling smaller,...

  18. Binder enhanced refuse derived fuel

    DOE Patents [OSTI]

    Daugherty, Kenneth E. (Lewisville, TX); Venables, Barney J. (Denton, TX); Ohlsson, Oscar O. (Naperville, IL)

    1996-01-01

    A refuse derived fuel (RDF) pellet having about 11% or more particulate calcium hydroxide which is utilized in a combustionable mixture. The pellets are used in a particulate fuel bring a mixture of 10% or more, on a heat equivalent basis, of the RDF pellet which contains calcium hydroxide as a binder, with 50% or more, on a heat equivalent basis, of a sulphur containing coal. Combustion of the mixture is effective to produce an effluent gas from the combustion zone having a reduced SO.sub.2 and polycyclic aromatic hydrocarbon content of effluent gas from similar combustion materials not containing the calcium hydroxide.

  19. Novel Binders and Methods for Agglomeration of Ore

    SciTech Connect (OSTI)

    S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

    2006-09-30

    Heap leaching is one of the methods being used to recover metal from low grade ore deposits. The main problem faced during heap leaching is the migration of fine grained particles through the heap, forming impermeable beds which result in poor solution flow. The poor solution flow leads to less contact between the leach solution and the ore, resulting in low recovery rates. Agglomeration of ore into coarse, porous masses prevents fine particles from migrating and clogging the spaces and channels between the larger ore particles. Currently, there is one facility in the United States which uses agglomeration. This operation agglomerates their ore using leach solution (raffinate), but is still experiencing undesirable metal recovery from the heaps due to agglomerate breakdown. The use of a binder, in addition to the leach solution, during agglomeration would help to produce stronger agglomerates that did not break down during processing. However, there are no known binders that will work satisfactorily in the acidic environment of a heap, at a reasonable cost. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. Increasing copper recovery in heap leaching by the use of binders and agglomeration would result in a significant decrease in the amount of energy consumed. Assuming that 70% of all the leaching heaps would convert to using agglomeration technology, as much as 1.64*10{sup 12} BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, which is equivalent to saving approximately 18% of the energy currently being used in leaching heaps. For every week a leach cycle was decreased, a savings of as much as 1.23*10{sup 11} BTU per week would result. This project has identified several acid-resistant binders and agglomeration procedures. These binders and experimental procedures will be able to be used for use in improving the energy efficiency of heap leaching.

  20. Fairness and stability of endtoend congestion Frank Kelly +

    E-Print Network [OSTI]

    Kelly, Frank

    , University of Cambridge, Wilberforce Road, Cam­ bridge CB3 0WB UK. Email: f.p.kelly@statslab.cam.ac.uk 1 #12 with the earlier telephony infrastructure where a smart network connects endpoints (telephones) that have little

  1. Battery components employing a silicate binder

    DOE Patents [OSTI]

    Delnick, Frank M. (Albuquerque, NM); Reinhardt, Frederick W. (Albuquerque, NM); Odinek, Judy G. (Rio Rancho, NM)

    2011-05-24

    A battery component structure employing inorganic-silicate binders. In some embodiments, casting or coating of components may be performed using aqueous slurries of silicates and electrode materials or separator materials.

  2. Resinous binders for coal and chars

    SciTech Connect (OSTI)

    Olson, E.S.; Sharma, R.K.; Young, B.C.

    1995-12-31

    Binder development and application to the briquetting or pelleting of coal fines has been extensive. The search for low-cost, effective binders for making strong and durable briquettes or pellets continues unabated. Strong, durable compacts are required, not only for handling, transport, and storage of the product but also to withstand the rigors of application such as flue gas treatment sorbents and catalytic supports. Many kinds of binders, organic and inorganic, have been used to gain the desired strength. Synthetic polymers have been investigated because they promote good strength and water insolubility, but these features are generally outweighed by the polymer cost. Promising earlier developments of biomass-derived binders have received slow market acceptance, mainly because of the cost resulting from the high concentrations required. However, recent advances in processing lignocellulosic materials have generated potentially low-cost polymeric binding agents for making coal briquettes. Phenol novolaks were previously used with lignites to make activated carbons. Recently, binders were prepared from mixtures of phenol, lignin, and formaldehyde and used for wood flour molding and friction materials. The goal of our work was to investigate the characteristics of resinous binders from lignocellulosic as well as coal-derived materials when used with dried or beneficiated coals and chars.

  3. Illustration: Sean Kelly Back to basics for the

    E-Print Network [OSTI]

    Wilson, W. Stephen

    Illustration: Sean Kelly Back to basics for the "division clueless" DECEMBER 6, 2010 | BY LISA research in algebraic topology to question basic math education. At two well- regarded private schools to only 31 percent of the 2006 students. As another experiment, Wilson gave a short test of basic math

  4. FOR IMMEDIATE RELEASE Contact: John F. Kelly

    E-Print Network [OSTI]

    Aronov, Boris

    comprehensive university system in the United States, educating more than 412,000 students in 6,688 degree morbidity and mortality rates. The researchers' findings, which appear in the January 2006 issue of Critical stated: "Over the past few years our laboratory developed efficient routes to synthesize sophorolipids

  5. 2015 Promotion and Tenure Main Binder Checklist Name _________________________________ College _________________________

    E-Print Network [OSTI]

    McQuade, D. Tyler

    2015 Promotion and Tenure Main Binder Checklist Name _________________________________ College _________________________ This is an outline; please use Attachment 1 of the P&T Memo for detailed instructions. Labeling the Main Binder SPOT and/or # 13 from SPCI https://java.apps.fsu.edu/sussai2/main.jsp ___SPOT/SPCI Summary Forms

  6. Human Artificial versus Natural Conceptualization of Spacetime Units Bernd Binder

    E-Print Network [OSTI]

    Binder, Bernd

    to a system of units. Additionally, the definition and measurement of the Newton constant does not involveHuman Artificial versus Natural Conceptualization of Spacetime Units Bernd Binder binder@quanics.com (Dated: 30.12.2003, www.quanics.com) The human international system of units (SI) is an artificial

  7. Human Artificial versus Natural Conceptualization of Spacetime Units Bernd Binder

    E-Print Network [OSTI]

    Binder, Bernd

    of units. Additionally, the definition and measurement of the Newton constant does not involve the lightHuman Artificial versus Natural Conceptualization of Spacetime Units Bernd Binder binder@quanics.com (Dated: 30.12.2003, www.quanics.com) The human international system of units (SI) is an artificial

  8. Dr. Kelli Joseph, NYISO Representing the ISO-RTO Council

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergyTher i n c i Framing DocumentUnits at Eight-<Dominion CoveDEC 2 4 2013EnergyKelli

  9. High-Rate, High-Capacity Binder-Free Electrode

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    that this process could be employed for any high-volume expansion material. * Volumetric capacity at 1C is 2000 mAhcm 3 (3 x graphite). Commercial Fe 3 O 4 material works...

  10. High-Rate, High-Capacity Binder-Free Electrode

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformation CurrentHenry Bellamy, Ph.D. Title: ProfessorHigh-Pressure MOFOffice of Energy

  11. Organic binders for iron ore pelletization and steelmaking

    SciTech Connect (OSTI)

    Karkoska, D.; Sankey, E. [Allied Colloids, Suffolk, VA (United States); Anderson, R. [Eveleth Mines, MN (United States)

    1995-12-01

    Historically, bentonite has been used in the agglomeration process in North American iron ore plants. In 1986, Eveleth Mines replaced bentonite with Peridur, a carboxy methyl cellulose organic binder used in conjunction with 1% limestone. Since May of 1993, Allied Colloids` Alcotac FE8 has been used by Eveleth as the replacement for bentonite. This paper discusses the performance benefits obtained when bentonite was replaced with an organic binder. These totally synthetic binders are used in conjunction with limestone. The benefits of organic binders are: improved metallurgical parameters of the fired pellet, especially the reducibility, which results in more efficient use of gases in the blast furnace; reduced silica in the pellet, in the case of Eveleth Mines this was a reduction of 0.5%, a lower silica pellet reduces slag in the blast furnace; increased production in both the agglomeration/induration and steelmaking processes; and a decrease in coke consumption.

  12. Moisture Diffusion in Asphalt Binders and Fine Aggregate Mixtures 

    E-Print Network [OSTI]

    Vasconcelos, Kamilla L.

    2011-08-08

    cost in highway maintenance and vehicle operations. One key mechanism of how moisture reaches the asphalt-aggregate interface is by its permeation or diffusion through the asphalt binder or mastic. Different techniques are available for diffusion...

  13. Internaltide generation and destruction by shoaling internal tides S. M. Kelly1

    E-Print Network [OSTI]

    Internaltide generation and destruction by shoaling internal tides S. M. Kelly1 and J. D. Nash1. [1] Internaltide generation is usually predicted from local topography, surface tides remotelygenerated shoaling internal tides induce firstorder changes in local internaltide generation. Theory

  14. FIA-13-0008- In the Matter of Michael J. Kelly

    Broader source: Energy.gov [DOE]

    On March 13, 2013, the Department of Energy’s (DOE) Office of Hearings and Appeals (OHA) denied a Freedom of Information Act (FOIA) Appeal filed by Michael J. Kelly (Appellant) of a determination...

  15. NOVEL BINDERS AND METHODS FOR AGGLOMERATION OF ORE

    SciTech Connect (OSTI)

    S.K. Kawatra; T.C. Eisele; J.A. Gurtler; C.A. Hardison; K. Lewandowski

    2004-04-01

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking.

  16. Constitutive behavior of particle-polymer binder composite

    SciTech Connect (OSTI)

    Zhang, D. Z. (Duan Z.); Ma, X. (Xia)

    2004-01-01

    A particle-binder composite can behave as a continuum solid and can also exhibit significant characters of dense granular flow depending on deformation conditions. When it behaves as continuum solid, polymer binder properties, especially the short time stress relaxation, significantly affects shock wave propagation through the composite. A constitutive model has been developed to account for the effects of the short time stress relaxation. The model compares well with experimental data. The model however does not consider the failure mechanisms of the material. The failure of the material closely depends on the manufacturing process. During the manufacturing process the binder bounding particles has not been cured while during the material failure process the binder bounds have already been destroyed or significantly weaken. Under these circumstances the composite flows like a dense granular material. The methods used in the studies of dense granular flow are introduced to study the particle-binder composite. Effects of interparticle forces on the macroscopic behavior of the material are studied. We find that the commonly used Voigt assumption in the study of composite materials is invalid for the particle-binder composite. Cohesion forces between particles determine the brittle or ductile behavior of the material during the failure process.

  17. RATES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and PACI Final FRN for Rate Order No. WAPA-139 - Notice of Order Temporarily Extending Formula Rates for Power, Transmission and Ancillary Services (PDF - 49K) Final FRN for Rate...

  18. RATES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - 392K) Final FRN for Rate Order No. WAPA-139 - Notice of Order Temporarily Extending Formula Rates for Power, Transmission and Ancillary Services (PDF - 49K) Final FRN for Rate...

  19. RATES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - Washoe Project, Stampede Division FERC Order Approving Extension of Non-Firm Power Formula Rate - Rate Order No. WAPA-160 (Sept. 5, 2013) (PDF - 22K) Notice of Extension of...

  20. Novel Binders and Methods for Agglomeration of Ore

    SciTech Connect (OSTI)

    S. K. Kawatra; T. C. Eisele; J. A. Gurtler

    2004-03-31

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. A primary example of this is copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process. As a result, operators of acidic heap-leach facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of other agglomeration applications, particularly advanced primary ironmaking.

  1. Electronically conductive polymer binder for lithium-ion battery electrode

    DOE Patents [OSTI]

    Liu, Gao; Xun, Shidi; Battaglia, Vincent S; Zheng, Honghe

    2014-10-07

    A family of carboxylic acid group containing fluorene/fluorenon copolymers is disclosed as binders of silicon particles in the fabrication of negative electrodes for use with lithium ion batteries. These binders enable the use of silicon as an electrode material as they significantly improve the cycle-ability of silicon by preventing electrode degradation over time. In particular, these polymers, which become conductive on first charge, bind to the silicon particles of the electrode, are flexible so as to better accommodate the expansion and contraction of the electrode during charge/discharge, and being conductive promote the flow battery current.

  2. Surface performance grading and grade selection process for surface treatment binders 

    E-Print Network [OSTI]

    Barcena Mendoza, Roberto

    2001-01-01

    ) or performance-graded (PG) asphalt binder specification was developed in the 1990's to measure binder properties directly related to hot mix asphalt concrete (HMAC) performance and included material characterization at low, intermediate, and high temperatures...

  3. Cationic fluorinated polymer binders for microbial fuel cell cathodes{ Guang Chen,ab

    E-Print Network [OSTI]

    or carbons) in the cathode is held in contact with the current collector using a polymer binder.12Cationic fluorinated polymer binders for microbial fuel cell cathodes{ Guang Chen,ab Bin Wei.1039/c2ra20705b Fluorinated quaternary ammonium-containing polymers were used as catalyst binders

  4. 3D phase-differentiated GDL microstructure generation with binder and PTFE distributions

    E-Print Network [OSTI]

    Kandlikar, Satish

    3D phase-differentiated GDL microstructure generation with binder and PTFE distributions Michael M of gas diffusion layer (GDL) materials with localized binder and poly- tetrafluoroethylene (PTFE mimics manufacturing processes and produces complete phase-differentiated (void, fiber, binder, and PTFE

  5. Effect of heat treatment on Si electrodes using polyvinylidene fluoride binder , L. Christensenb

    E-Print Network [OSTI]

    Hewitt, Kevin

    1 Effect of heat treatment on Si electrodes using polyvinylidene fluoride binder Jing Lia , L and adhesion tests. It is suggested that heat treatment improves the binder distribution, the adhesion performance of Si electrodes using polyvinylidene fluoride (PVDF) binder heated at different temperatures

  6. Novel anti-flooding poly(dimethylsiloxane) (PDMS) catalyst binder for microbial fuel cell cathodes

    E-Print Network [OSTI]

    Novel anti-flooding poly(dimethylsiloxane) (PDMS) catalyst binder for microbial fuel cell cathodes 2012 Keywords: Microbial fuel cell Poly(dimethylsiloxane) Anti-flooding Catalyst binder a b s t r a c]. Nafion has been used as a standard catalyst binder polymer for MFCs, due to its high proton conduc

  7. Energy Efficient Process Heating: Insulation and Thermal Mass Kevin Carpenter and Kelly Kissock

    E-Print Network [OSTI]

    Kissock, Kelly

    1 Energy Efficient Process Heating: Insulation and Thermal Mass Kevin Carpenter and Kelly Kissock tanks and reducing thermal mass. A companion paper, Energy Efficiency Process Heating: Managing Air Flow of the oven/furnace. Reducing the quantity of energy lost to thermal mass in a process heating system saves

  8. Net Energy Costs of Skylights Peter Kleinhenz, Rizwan Syed, and Kelly Kissock,

    E-Print Network [OSTI]

    Kissock, Kelly

    per square foot of floor area per year using average 2005 industrial energy costs. Net cooling energyNet Energy Costs of Skylights Peter Kleinhenz, Rizwan Syed, and Kelly Kissock, University of Dayton, it is also useful to consider the net energy costs associated with skylights. This paper describes

  9. State preservation by repetitive error detection in a superconducting quantum circuit J. Kelly,1,

    E-Print Network [OSTI]

    Martinis, John M.

    State preservation by repetitive error detection in a superconducting quantum circuit J. Kelly,1 , and superconducting circuits11­13 have demonstrated multi-qubit states that are first-order toler- ant to one type of error. Recently, experiments with ion traps and superconducting circuits have shown the simultaneous de

  10. Land Tenure and Land Administration Issues in Guatemala Danielle Kelly Donovan

    E-Print Network [OSTI]

    Onsrud, Harlan J.

    Land Tenure and Land Administration Issues in Guatemala Danielle Kelly Donovan danielle.donovan@spatial.maine.edu May 2002 1. Abstract The evolution of land tenure in Guatemala is a mix of the native Mayan implementation stage, when the CIA began "Operation Success". The operation sent mercenaries into Guatemala

  11. 7.1 Classical Control Mobile Robotics -Prof Alonzo Kelly, CMU RI1

    E-Print Network [OSTI]

    Nourbakhsh, Illah

    Control ­ 7.1.4 Model Referenced and Feedforward Control ­ Summary Mobile Robotics - Prof Alonzo Kelly.1.3 Feedback Control ­ 7.1.4 Model Referenced and Feedforward Control ­ Summary Mobile Robotics - Prof Alonzo, power) ­ onto controlled variables (positions, velocities) · Feedback alters the dynamics of a system to

  12. Energy Efficient Process Heating: Managing Air Flow Kevin Carpenter and Kelly Kissock

    E-Print Network [OSTI]

    Kissock, Kelly

    Energy Efficient Process Heating: Managing Air Flow Kevin Carpenter and Kelly Kissock Department important aspect to consider when attempting to improve the energy efficiency of most process heating. Infiltration air enters the system through openings in the system shell. For energy- efficient process heating

  13. UNDERSTANDING MANUFACTURING ENERGY USE THROUGH STATISTICAL ANALYSIS KELLY KISSOCK AND JOHN SERYAK

    E-Print Network [OSTI]

    Kissock, Kelly

    UNDERSTANDING MANUFACTURING ENERGY USE THROUGH STATISTICAL ANALYSIS KELLY KISSOCK AND JOHN SERYAK, OHIO ABSTRACT Energy in manufacturing facilities is used for direct production of goods, space for statistically analyzing plant energy use in terms of these major end uses. The methodology uses as few as 60

  14. Biofuels `101'Michael Wilcox, Dayton Lambert and Kelly Tiller Assistant Professors, Department of Agricultural Economics

    E-Print Network [OSTI]

    Grissino-Mayer, Henri D.

    Biofuels `101'Michael Wilcox, Dayton Lambert and Kelly Tiller Assistant Professors, Department vehicle emissions. Biofuels Non-petroleum sources of transportation fuels include natu- ral gas (2.2 percent) and biofuels (1.1 percent). While used in small amounts now, demand for biofuels (ethanol

  15. A FEASIBILITY STUDY OF FUEL CELL COGENERATION IN INDUSTRY Scott B. Phelps and J. Kelly Kissock

    E-Print Network [OSTI]

    Kissock, Kelly

    A FEASIBILITY STUDY OF FUEL CELL COGENERATION IN INDUSTRY Scott B. Phelps and J. Kelly Kissock of the literature on fuel cell cogeneration describes cogeneration at commercial sites. In this study, a PC25C phosphoric acid fuel cell cogeneration system was designed for an industrial facility and an economic

  16. 11 . Alternative reproductive tactics In amphibians KELLY R . ZAMUDIO AND LAURE

    E-Print Network [OSTI]

    Zamudio, Kelly R.

    11 . Alternative reproductive tactics In amphibians KELLY R . ZAMUDIO AND LAURE CHAPTER SUMMARY a surprising diversity of alternative reproductive phenotypes that can roughly be divided into two classes of alternative reproductive tactics. However, OUf understanding of the evolution of amphibian alternative

  17. Low-loss binder for hot pressing boron nitride

    DOE Patents [OSTI]

    Maya, Leon (Oak Ridge, TN)

    1991-01-01

    Borazine derivatives used as low-loss binders and precursors for making ceramic boron nitride structures. The derivative forms the same composition as the boron nitride starting material, thereby filling the voids with the same boron nitride material upon forming and hot pressing. The derivatives have a further advantage of being low in carbon thus resulting in less volatile byproduct that can result in bubble formation during pressing.

  18. A new binder for powder injection molding titanium and other reactive metals

    SciTech Connect (OSTI)

    Weil, K. Scott; Nyberg, Eric A.; Simmons, Kevin L.

    2006-06-26

    We have developed a new aromatic-based binder for powder injection molding (PIM) reactive metals, such as titanium, zirconium, niobium, tungsten, and molybdenum. Because of careful selection of the binder constituents, thermal removal is readily accomplished at low temperatures and short-times via vacuum sublimation. In this way the binder can be cleanly extracted from the green part prior to sintering to minimize the amount of residual carbon left in the final component. Rheological measurements indicate that powder loadings in the PIM feedstock as high as 67 vol% could be achieved using the new binder system, while still maintaining low mixing torques and injection molding pressures.

  19. Upgrading mild gasification liquids to produce electrode binder pitch. Technical report, 1 March--31 May 1994

    SciTech Connect (OSTI)

    Knight, R.A. [Inst. of Gas Technology, Chicago, IL (United States)

    1994-09-01

    The objective of this program is to investigate the production of electrode binder pitch, valued at $250--$300/ton, from mild gasification liquids. The IGT MILDGAS process pyrolyzes coal at 650--760 C and, with Illinois coal, the 400 C+ distillation residue (crude pitch) comprises 40--70% of the MILDGAS liquids, representing up to 20 wt% of maf feed coal. The largest market for pitch made from coal liquids is the aluminum industry, which uses it to make carbon anodes for electrolytic furnaces. In this project, crude MILDGAS pitch is being modified by a flash thermocracking technique to achieve specifications typical of a binder pitch. Last year, a pitch thermocracking unit was constructed for operation at 650--900 F. Process conditions are being examined to optimize the properties of the finished pitch and coke. In the current year, improvements to the thermocracker were made for better gas and pitch flow control, continuous electronic monitoring of feed rate and pressures, and improvements to allow longer tests. During the current quarter, five thermocracking tests were conducted in 100% N{sub 2}, 50% H{sub 2}/N{sub 2}, and 100% H{sub 2}. Test temperatures were 758--873 C with residence times of 1.86--2.42 s and pitch:gas ratios of 0.90--1.10 {times} 10{sup {minus}4}. Product analyses showed that there was no significant effect of H{sub 2} on the pitch sulfur content, but the pitch sulfur content was significantly reduced at higher temperature.

  20. Ductile Binder Phase For Use With Almgb14 And Other Hard Ceramic Materials

    DOE Patents [OSTI]

    Cook, Bruce A. (Ankeny, IA); Russell, Alan (Ames, IA); Harringa, Joel (Ames, IA)

    2005-07-26

    This invention relates to a ductile binder phase for use with AlMgB14 and other hard materials. The ductile binder phase, a cobalt-manganese alloy, is used in appropriate quantities to tailor good hardness and reasonable fracture toughness for hard materials so they can be used suitably in industrial machining and grinding applications.

  1. A Natural Mass Unit Hidden in the Planck Action Quantum Bernd Binder

    E-Print Network [OSTI]

    Binder, Bernd

    A Natural Mass Unit Hidden in the Planck Action Quantum Bernd Binder binder@quanics.com c 2003 baryon mass a natural mass unit µ can be identified by extrapolating dimensionless Planck units h = c = 1 to the System of Units (SI). Similar to quantum measurements that determine h it is only necessary to relate

  2. A Natural Mass Unit Hidden in the Planck Action Quantum Bernd Binder

    E-Print Network [OSTI]

    Binder, Bernd

    A Natural Mass Unit Hidden in the Planck Action Quantum Bernd Binder binder@quanics.com c #2003 baryon mass a natural mass unit µ can be identified by extrapolating dimensionless Planck units h = c = 1 to the System of Units (SI). Similar to quantum measurements that determine h it is only necessary to relate

  3. Preparation of Solid Alkaline Fuel Cell Binders Based on Fluorinated Poly(diallyldimethylammonium chloride)s

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Preparation of Solid Alkaline Fuel Cell Binders Based on Fluorinated Poly to be used in a Solid Alkaline Fuel Cell (SAFC) needs to (i) be insoluble in both aqueous solutions,10% > 320 °C). When used in a fuel cell as a binder in the membrane-electrodes assembly (MEA

  4. The curing of asphalt with rubber and its effect on the physical and chemical properties of asphalt-rubber binders 

    E-Print Network [OSTI]

    Chun, Jay Sung

    1995-01-01

    The objective of this research was to develop a potentially useful asphalt-rubber binder using the curing process. For the curing process, six parameters, which altered the physical and chemical properties of the asphalt-rubber binder, were tested...

  5. A Model for the Nonlinear Mechanical Behavior of Asphalt Binders and its Application in Prediction of Rutting Susceptibility 

    E-Print Network [OSTI]

    Srinivasa Parthasarathy, Atul

    2013-04-30

    The mechanical behavior of asphalt binders is nonlinear. The binders exhibit shear thinning/thickening behavior in steady shear tests and non-proportational behavior in other standard viscoelastic tests such as creep-recovery ...

  6. The Effects of Various Conductive Additive and Polymeric Binder Contents on the Performance of a Lithium-ion Composite

    E-Print Network [OSTI]

    Liu, G.

    2008-01-01

    conductive additive, and polyvinylidene difluoride (PVDF), a polymer binder) on the power performance of lithium-ion composite

  7. Effects of ageing on different binders for retouching and on some binder-pigment combinations used for restoration of wall paintings

    SciTech Connect (OSTI)

    Ropret, P. Zoubek, R.; Skapin, A. Sever Bukovec, P.

    2007-11-15

    In restoration of colour layers, the selection of the most appropriate retouching binder is a very important step that may have a crucial impact on materials durability. As different weather conditions can have versatile influence on stability of colour layers, we determined the effect of ageing on carefully selected samples of binders (Tylose, Klucel, ammonium caseinate, gum arabicum, fish and skin glues and some other synthetic binders) as well as on several binder-pigment combinations (the pigments in combinations being cinnabar, green earth and smalt). The samples were subjected to accelerated ageing tests in climatic chambers. In these tests the temperature and the relative humidity were daily oscillating between - 20 deg. C and 50 deg. C and 50% to 90%, respectively, for a period of one month. Then the samples were exposed to UV and visible light generated by a metal halide lamp for a month. The differences in microstructure before and after ageing were determined by optical and scanning electron microscopy, while the ageing of the organic structures in binders was investigated by Fourier transform infrared (FTIR) microscopy.

  8. Factors affecting binder properties between production and construction and their impact on quality assurance programs 

    E-Print Network [OSTI]

    Arambula Mercado, Edith

    2002-01-01

    . In Texas, QA testing is done immediately after binder production, regardless of the fact that the material undergoes several storage and transfer processes before it reaches the construction site or hot mix asphalt (HMA) plant. Storage at elevated...

  9. Evaluation of healing in asphalt binders using dynamic shear rheometer and molecular modeling techniques 

    E-Print Network [OSTI]

    Bommavaram, Ramamohan Reddy

    2009-05-15

    A self-healing material has the inherent ability to partially reverse damage such as crack formation that might have occurred during its service. Significant evidence exists in the literature to indicate that asphalt binder ...

  10. The effects of asphalt binder oxidation on hot mix asphalt concrete mixture rheology and fatigue performance 

    E-Print Network [OSTI]

    Jung, Sung Hoon

    2009-06-02

    Asphalt oxidation causes major changes to binder properties and is hypothesized to be a major contributor to age-related pavement failure such as fatigue cracking. Extensive laboratory aging research has been done to assess ...

  11. The effect of air blowing on the properties of rubber-modified asphalt binder 

    E-Print Network [OSTI]

    Bauer, Shauna Erin

    1997-01-01

    Recently, crumb rubber modifier or CRM has become prevalent in the construction of flexible pavements. This work addresses the phase separation that is commonly encountered with asphalt-rubber binders subjected to prolonged ...

  12. Effects of the polymeric binder system in slurry-based three dimensional printing of ceramics

    E-Print Network [OSTI]

    Holman Richard K. (Richard Kimbrough), 1973-

    2001-01-01

    The factors dictating the minimum feature size in Slurry-based Three Dimensional Printing (S-3DPTM) of ceramics have been examined, focusing on effects related to the polymeric binder system polyacrylic acid (PAA, MW 60000) ...

  13. Climate Change and Disease Ecology You are invited to join Drew Harvell, Kelly Zamudio, and Laura Harrington for a lunch

    E-Print Network [OSTI]

    Walter, M.Todd

    Climate Change and Disease Ecology You are invited to join Drew Harvell, Kelly Zamudio, and Laura Future (CCSF) on "Climate Change and Disease Ecology". Our goal is to provide a forum for discussion studies of disease ecology and climate change. We are interesting to discuss initially effects

  14. Economics of Energy Efficiency in a CO2 Constrained World Daniel Trombley and Kelly Kissock, University of Dayton

    E-Print Network [OSTI]

    Kissock, Kelly

    Economics of Energy Efficiency in a CO2 Constrained World Daniel Trombley and Kelly Kissock energy certificates, and improving energy efficiency on site. This paper investigates the economics of energy efficiency in comparison to purchasing renewable energy certificates or CO2 emission reduction

  15. Goal-Based Safety Standards: Opportunities and Challenges Tim Kelly, University of York, Heslington, York, YO10 5DD UK

    E-Print Network [OSTI]

    Kelly, Tim

    with how systems are developed and assessed, e.g. methods of safety analysis and criteria for risk, in safety, this is to establish safety requirements, design to meet the agreed requirements, and to showGoal-Based Safety Standards: Opportunities and Challenges Tim Kelly, University of York, Heslington

  16. Poly(lactic acid) degradable plastics, coatings, and binders

    SciTech Connect (OSTI)

    Bonsignore, P.V.; Coleman, R.D.; Mudde, J.P.

    1992-01-01

    Biochemical processes to derive value from the management of high carbohydrate food wastes, such as potato starch, corn starch, and cheese whey permeate, have typically been limited to the production of either ethanol or methane. Argonne National Laboratory (ANL) believes that lactic acid presents an attractive option for an alternate fermentation end product, especially in light of lactic acids' being a viable candidate for conversion to environmentally safe poly(lactic acid) (PLA) degradable plastics, coatings, and binders. Technology is being developed at ANL to permit a more cost effective route to modified high molecular weight PLA. Preliminary data on the degradation behavior of these modified PLAs shows the retention to the inherent hydrolytic degradability of the PLA modified, however, by introduced compositional variables. A limited study was done on the hydrolytic stability of soluble oligomers of poly(L-lactic acid). Over a 34 day hold period, water-methanol solutions of Pl-LA oligomers in the 2-10 DP range retained some 75% of their original molecular weight.

  17. Poly(lactic acid) degradable plastics, coatings, and binders

    SciTech Connect (OSTI)

    Bonsignore, P.V.; Coleman, R.D.; Mudde, J.P.

    1992-05-01

    Biochemical processes to derive value from the management of high carbohydrate food wastes, such as potato starch, corn starch, and cheese whey permeate, have typically been limited to the production of either ethanol or methane. Argonne National Laboratory (ANL) believes that lactic acid presents an attractive option for an alternate fermentation end product, especially in light of lactic acids` being a viable candidate for conversion to environmentally safe poly(lactic acid) (PLA) degradable plastics, coatings, and binders. Technology is being developed at ANL to permit a more cost effective route to modified high molecular weight PLA. Preliminary data on the degradation behavior of these modified PLAs shows the retention to the inherent hydrolytic degradability of the PLA modified, however, by introduced compositional variables. A limited study was done on the hydrolytic stability of soluble oligomers of poly(L-lactic acid). Over a 34 day hold period, water-methanol solutions of Pl-LA oligomers in the 2-10 DP range retained some 75% of their original molecular weight.

  18. Kelley Hot Spring Geothermal Project: Kelly Hot Spring Agricultural Center conceptual design

    SciTech Connect (OSTI)

    Longyear, A.B. (ed.)

    1980-06-01

    The proposed core activity in the Kelly Hot Spring Agricultural Center is a nominal 1200 sow swine raising complex. The swine raising is to be a totally confined operation for producing premium pork in controlled environment facilities that utilize geothermal energy. The complex will include a feedmill for producing the various feed formulae required for the animals from breeding through gestation, farrowing, nursery, growing and finishing. The market animals are shipped live by truck to slaughter in Modesto, California. A complete waste management facility will include manure collection from all raising areas, transport via a water flush sysem to methane (biogas) generators, manure separation, settling ponds and disposition of the surplus agricultural quality water. The design is based upon the best commercial practices in confined swine raising in the US today. The most unique feature of the facility is the utilization of geothermal hot water for space heating and process energy throughout the complex.

  19. An Ultra-Low-Power Analog Memory System with an Adaptive Sampling Rate

    E-Print Network [OSTI]

    Graham, David W.

    An Ultra-Low-Power Analog Memory System with an Adaptive Sampling Rate Brandon M. Kelly, Brandon normally associated with sleep states in WSNs, we introduce an ultra-low-power analog memory buffer in which ultra- low-power operation is a necessity. In this paper, we propose an ultra-low-power analog mem

  20. Hydration and strength development of binder based on high-calcium oil shale fly ash

    SciTech Connect (OSTI)

    Freidin, C. [Ben-Gurion Univ. of the Negev, Sede-Boqer (Israel)] [Ben-Gurion Univ. of the Negev, Sede-Boqer (Israel)

    1998-06-01

    The properties of high-calcium oil shale fly ash and low-calcium coal fly ash, which are produced in Israeli power stations, were investigated. High-calcium oil shale fly ash was found to contain a great amount of CaO{sub free} and SO{sub 3} in the form of lime and anhydrite. Mixtures of high-calcium oil shale fly ash and low-calcium coal fly ash, termed fly ash binder, were shown to cure and have improved strength. The influence of the composition and curing conditions on the compressive strength of fly ash binders was examined. The microstructure and the composition of fly ash binder after curing and long-term exposure in moist air, water and open air conditions were studied. It was determined that ettringite is the main variable in the strength and durability of cured systems. The positive effect of calcium silicate hydrates, CSH, which are formed by interaction of high-calcium oil shale fly ash and low-calcium coal fly ash components, on the carbonation and dehydration resistance of fly ash binder in open air is pronounced. It was concluded that high-calcium oil shale fly ash with high CaO{sub free} and SO{sub 3} content can be used as a binder for building products.

  1. Selective catalytic reduction system and process using a pre-sulfated zirconia binder

    DOE Patents [OSTI]

    Sobolevskiy, Anatoly; Rossin, Joseph A.

    2010-06-29

    A selective catalytic reduction (SCR) process with a palladium catalyst for reducing NOx in a gas, using hydrogen as a reducing agent is provided. The process comprises contacting the gas stream with a catalyst system, the catalyst system comprising (ZrO.sub.2)SO.sub.4, palladium, and a pre-sulfated zirconia binder. The inclusion of a pre-sulfated zirconia binder substantially increases the durability of a Pd-based SCR catalyst system. A system for implementing the disclosed process is further provided.

  2. A molecular thermodynamic view of DNAdrug interactions: a case study of 25 minor-groove binders

    E-Print Network [OSTI]

    Jayaram, Bhyravabotla

    A molecular thermodynamic view of DNA­drug interactions: a case study of 25 minor-groove binders-groove recognition by small molecules via a computational study on 25 DNA­drug complexes. The studies are configured of this study. While highlighting the favorable role of packing, shape complementarity, and van der Waals

  3. CoOcarbon nanofiber networks prepared by electrospinning as binder-free anode materials for

    E-Print Network [OSTI]

    Cao, Guozhong

    for lithium-ion batteries with enhanced properties Ming Zhang,ab Evan Uchaker,a Shan Hu,a Qifeng Zhang(II) acetate and polyacrylonitrile by an electrospinning method followed by thermal treatment. The XPS results with diameters of 200 nm. As binder-free anodes for lithium-ion batteries, the discharge capacities of such Co

  4. Epitope-Guided Engineering of Monobody Binders for in Vivo Inhibition of Erk2 Signaling

    E-Print Network [OSTI]

    Ferkey, Denise

    Epitope-Guided Engineering of Monobody Binders for in Vivo Inhibition of Erk2 Signaling Jasdeep K a defined surface patch on the mitogen activated protein kinase (MAPK) Erk-2. The targeted area ("CD" domain be useful for regulating Erk- 2 signaling in vivo. Although the CD domain constitutes only a small

  5. 1 INTRODUCTION Asphalt mixtures are composite materials that consist of solid particles, viscous binder/fluid

    E-Print Network [OSTI]

    Luding, Stefan

    binder/fluid (bitumen) and pores filled with air. When considering asphalt we should distinguish in the skeleton move close to each other and air in the voids is squeezed out. The fluid in the mixture (that can of the bitumen layer between the particles are only partly involved in this kind of approach. The discrete

  6. Determining the slag fraction, water/binder ratio and degree of hydration in hardened cement pastes

    SciTech Connect (OSTI)

    Yio, M.H.N. Phelan, J.C.; Wong, H.S.; Buenfeld, N.R.

    2014-02-15

    A method for determining the original mix composition of hardened slag-blended cement-based materials based on analysis of backscattered electron images combined with loss on ignition measurements is presented. The method does not require comparison to reference standards or prior knowledge of the composition of the binders used. Therefore, it is well-suited for application to real structures. The method is also able to calculate the degrees of reaction of slag and cement. Results obtained from an experimental study involving sixty samples with a wide range of water/binder (w/b) ratios (0.30 to 0.50), slag/binder ratios (0 to 0.6) and curing ages (3 days to 1 year) show that the method is very promising. The mean absolute errors for the estimated slag, water and cement contents (kg/m{sup 3}), w/b and s/b ratios were 9.1%, 1.5%, 2.5%, 4.7% and 8.7%, respectively. 91% of the estimated w/b ratios were within 0.036 of the actual values. -- Highlights: •A new method for estimating w/b ratio and slag content in cement pastes is proposed. •The method is also able to calculate the degrees of reaction of slag and cement. •Reference standards or prior knowledge of the binder composition are not required. •The method was tested on samples with varying w/b ratios and slag content.

  7. TYPES OF PAINT DIY CHECKLIST Consists of pigments, additives and binders in an oil or

    E-Print Network [OSTI]

    Peters, Richard

    TYPES OF PAINT DIY CHECKLIST PAINT · Consists of pigments, additives and binders in an oil or water of application and durability. · Cheaper paint generally contains more solvents than more expensive paint-based). · Oil-based (solvent-/polyurethane-based, also known as alkyd paint). · Natural (eg. mineral paint

  8. PRESSURE AND TEMPERATURE DEPENDENT DEFLAGRATION RATE MEASUREMENTS OF LLM-105 AND TATB BASED EXPLOSIVES

    SciTech Connect (OSTI)

    Glascoe, E A; Tan, N; Koerner, J; Lorenz, K T; Maienschein, J L

    2009-11-10

    The pressure dependent deflagration rates of LLM-105 and TATB based formulations were measured in the LLNL high pressure strand burner. The role of binder amount, explosive type, and thermal damage and their effects on the deflagration rate will be discussed. Two different formulations of LLM-105 and three formulations of TATB were studied and results indicate that binder amount and type play a minor role in the deflagration behavior. This is in sharp contrast to the HMX based formulations which strongly depend on binder amount and type. The effect of preheating these samples was considerably more dramatic. In the case of LLM-105, preheating the sample appears to have little effect on the deflagration rate. In contrast, preheating TATB formulations causes the deflagration rate to accelerate and become erratic. The thermal and mechanical properties of these formulations will be discussed in the context of their pressure and temperature dependent deflagration rates.

  9. Deflagration Rate Measurements of Three Insensitive High Explosives: LLM-105, TATB, and DAAF

    SciTech Connect (OSTI)

    Glascoe, E A; Maienschein, J L; Lorenz, K T; Tan, N; Koerner, J G

    2010-03-08

    The pressure dependent deflagration rates of LLM-105, DAAF and TATB based formulations were measured in the LLNL high pressure strand burner. The role of binder amount, explosive type, and thermal damage and their effects on the deflagration rate will be discussed. One DAAF formulation, two different formulations of LLM-105, and four formulations of TATB were studied; results indicate that binder amount and type play a minor role in the deflagration behavior. This is in sharp contrast to the HMX based formulations which strongly depend on binder amount and type. The effect of preheating these samples was considerably more dramatic. In the case of LLM-105, preheating the sample appears to have little effect on the deflagration rate. In contrast, preheating DAAF and TATB formulations causes the deflagration rate to accelerate. The thermal and mechanical properties of these formulations will be discussed in the context of their pressure and temperature dependent deflagration rates.

  10. The Effects of Various Conductive Additive and Polymeric Binder Contents on the Performance of a Lithium-ion Composite

    SciTech Connect (OSTI)

    Stevenson, Cynthia; Liu, G.; Zheng, H.; Kim, S.; Deng, Y.; Minor, A.M.; Song, X.; Battaglia, V.S.

    2008-08-07

    Fundamental electrochemical methods, cell performance tests, and physical characterization tests such as electron microscopy were used to study the effects of levels of the inert materials (acetylene black (AB), a nano-conductive additive, and polyvinylidene difluoride (PVDF), a polymer binder) on the power performance of lithium-ion composite cathodes. The electronic conductivity of the AB/PVDF composites at different compositions was measured with a four-point probe direct current method. The electronic conductivity was found to increase rapidly and plateau at a AB:PVDF ratio 0.2:1 (by weight), with 0.8:1 being the highest conductivity composition. AB:PVDF compositions along the plateau of 0.2:1, 0.4:1, 0.6:1 and 0.8:1 were investigated. Electrodes of each of those compositions were fabricated with different fractions of AB/PVDF to active material. It was found that at the 0.8:1 AB:PVDF, the rate performance improved with increases in the AB/PVDF loading, whereas at the 0.2:1 AB:PVDF, the rate performance improved with decreases in the AB/PVDF loading. The impedance of electrodes made with 0.6:1 AB:PVDF was low and relatively invariant.

  11. Hybrid CuO/SnO{sub 2} nanocomposites: Towards cost-effective and high performance binder free lithium ion batteries anode materials

    SciTech Connect (OSTI)

    Xing, G. Z.; Wang, Y.; Wong, J. I.; Shi, Y. M.; Huang, Z. X.; Yang, H. Y.; Li, S.

    2014-10-06

    Hybrid CuO/SnO{sub 2} nanocomposites are synthesized by a facile thermal annealing method on Cu foils. Compared to pristine CuO and SnO{sub 2} nanostructures, hybrid CuO/SnO{sub 2} nanocomposites exhibit the enhanced electrochemical performances as the anode material of lithium ion batteries (LIBs) with high specific capacity and excellent rate capability. The binder free CuO/SnO{sub 2} nanocomposites deliver a specific capacity of 718 mA h g{sup ?1} at a current density of 500?mA g{sup ?1} even after 200 cycles. The enhanced electrochemical performances are attributed to the synergistic effect between SnO{sub 2} nanoparticles and CuO nanoarchitectures. Such hybrid CuO/SnO{sub 2} nanocomposites could open up a new route for the development of next-generation high-performance and cost-effective binder free anode material of LIBs for mass production.

  12. Utilizing New Binder Materials for Green Building has Zero Waste by Recycling Slag and Sewage Sludge Ash 

    E-Print Network [OSTI]

    Zeedan, S. R.

    2010-01-01

    binding material to save energy and to produce new innovative zero materials waste . The current research aims to investigate new binder materials as alternative of Portland cement. Alkali activated slag (AAS) blended with sewage sludge ash (SSA...

  13. Supercritical Solubility of Binders Used in Explosive Formulations

    SciTech Connect (OSTI)

    David A. Bell

    2002-09-14

    The dissolution of polymers in supercritical carbon dioxide was measured using in-situ ultraviolet absorbance. This research was carried out to provide data to support the development of a new process to produce plastic-bonded explosive molding powder. Estane 5703, the polymer used to bind PBX 9501, was insoluble at the tested conditions. The dissolution of Kraton FG 1901 was tested at 27 to 100{degrees}C and 29 to 65 MPa. Only a small fraction of this polymer dissolved, and the quantity that dissolved increased with the polymer sample size. The tested polymer was polydisperse, and it is thought that the lowest molecular weight fraction of the polymer preferentially dissolved. Based on this observation, dissolution of the polymer prior to molding powder synthesis is recommended to obtain a uniform molding powder product. The dissolution of nearly monodisperse samples of polyethylacrylate were tested at 27 to 90{degrees}C and 10 to 65 MPa. The resulting solutions were very dilute, on the order of 100 mg/liter, and the solutions did not reach saturation during the 90 hour test period. The slow approach to saturation indicates that mass transfer rates may significantly affect process performance.

  14. COLLINS, KELLY ALYSSA. A Field Evaluation of Four Types of Permeable Pavement with Respect to Water Quality Improvement and Flood Control. (Under the direction of

    E-Print Network [OSTI]

    Hunt, William F.

    ABSTRACT COLLINS, KELLY ALYSSA. A Field Evaluation of Four Types of Permeable Pavement with Respect of porous concrete (PC), two types of permeable interlocking concrete pavers (PICP) with gravel fill significantly lower outflow volumes than #12;asphalt and the other permeable pavement sections evaluated (p

  15. The Cascade of Tidal Energy from Low to High Modes on a Continental Slope SAMUEL M. KELLY* AND JONATHAN D. NASH

    E-Print Network [OSTI]

    The Cascade of Tidal Energy from Low to High Modes on a Continental Slope SAMUEL M. KELLY 25 March 2012) ABSTRACT The linear transfer of tidal energy from large to small scales is quantified. Observed transfer of tidal energy into high-mode internal tides is quantitatively consistent with observed

  16. By Kelly Riddell -Feb 18, 2011 The president can't use emergency measures to order an Internet shutdown to combat cyber attacks,

    E-Print Network [OSTI]

    Valtorta, Marco

    shutting down the Internet during a national crisis. It also permits owners of major computer systems, to appeal their status in federal court. Concern about giving the president authority to shut downBy Kelly Riddell - Feb 18, 2011 The president can't use emergency measures to order an Internet

  17. Grass Roots Entrepreneurship and Innovation: Micro-Enterprise in Social Care Kelly Hall, Catherine Needham and Kerry Allen, University of Birmingham, UK

    E-Print Network [OSTI]

    Birmingham, University of

    1 Grass Roots Entrepreneurship and Innovation: Micro-Enterprise in Social Care Kelly Hall conceptions of social care and have been promoted by the UK government as highly innovative, personalised to which they outperform larger care providers in delivering valued, innovative, personalised and cost

  18. Nocturnal light and lunar cycle effects on diel migration of micronekton Kelly J. Benoit-Bird,a,* Whitlow W. L. Au,b and Daniel W. Wisdoma

    E-Print Network [OSTI]

    Benoit-Bird, Kelly J.

    Nocturnal light and lunar cycle effects on diel migration of micronekton Kelly J. Benoit Abstract The roles of nocturnal light and lunar phase in the diel migration of micronekton from a nearshore. However, this movement was not enough to compensate for observed changes in light, and at night animals

  19. Gel nanostructure in alkali-activated binders based on slag and fly ash, and effects of accelerated carbonation

    SciTech Connect (OSTI)

    Bernal, Susan A.; Provis, John L.; Walkley, Brant; San Nicolas, Rackel; Gehman, John D.; Brice, David G.; Kilcullen, Adam R.; Zeobond Pty Ltd, P.O. Box 23450, Docklands, Victoria 8012 ; Duxson, Peter; Deventer, Jannie S.J. van

    2013-11-15

    Binders formed through alkali-activation of slags and fly ashes, including ‘fly ash geopolymers’, provide appealing properties as binders for low-emissions concrete production. However, the changes in pH and pore solution chemistry induced during accelerated carbonation testing provide unrealistically low predictions of in-service carbonation resistance. The aluminosilicate gel remaining in an alkali-activated slag system after accelerated carbonation is highly polymerised, consistent with a decalcification mechanism, while fly ash-based binders mainly carbonate through precipitation of alkali salts (bicarbonates at elevated CO{sub 2} concentrations, or carbonates under natural exposure) from the pore solution, with little change in the binder gel identifiable by nuclear magnetic resonance spectroscopy. In activated fly ash/slag blends, two distinct gels (C–A–S–H and N–A–S–H) are formed; under accelerated carbonation, the N–A–S–H gel behaves comparably to fly ash-based systems, while the C–A–S–H gel is decalcified similarly to alkali-activated slag. This provides new scope for durability optimisation, and for developing appropriate testing methodologies. -- Highlights: •C-A-S-H gel in alkali-activated slag decalcifies during accelerated carbonation. •Alkali-activated fly ash gel changes much less under CO{sub 2} exposure. •Blended slag-fly ash binder contains two coexisting gel types. •These two gels respond differently to carbonation. •Understanding of carbonation mechanisms is essential in developing test methods.

  20. The use of nonmuscle proteins as binders in various meat systems 

    E-Print Network [OSTI]

    Crenwelge, Carolyn Hibbs

    1980-01-01

    . HE USE OF ?OHMCSWE "HC EL'lg AS 3&~iEBS ? FARIOUS MEAT SYST&i~ A Thesis CAHOLDI HIBBS CBE?KELGE Submitted =o the Coaduate Coll ge of Texas A&M University in Fartial fulfillment of the requirement for the d gree of MASTER OF SCIEllCE May i... of Committee) / (Membe ) (Nember) ( ead of Depar ent) May I980 ABSTRACT I'he Use of Nonmuscle Proteins as Binders in Various Meat Systems. (May 1980) Carolyn Hibbs Czenwelge, B. S. , Texas A6M University Co-chairmen of Advisory Committee: Dr. Robert...

  1. Use of a Naphthalene-Based Binder in Injection Molding Net-Shape Titanium Components of Controlled Porosity

    SciTech Connect (OSTI)

    Weil, K. Scott; Nyberg, Eric A.; Simmons, Kevin L.

    2005-07-01

    We have recently developed a naphthalene-based binder system for use in powder injection molding (PIM) of ceramic and metallic materials. The use of a binder that can be removed via sublimation offers several unique advantages relative to the typical thermoplastic and/or thermoset binders employed in PIM. One of these is that essentially no volume change takes place during debindering. This offers a relatively facile method of introducing porosity into a net-shape part of potentially complex geometry. In the study described in this paper, the effects of powder loading and subsequent isostatic compaction on the size and amount of porosity in the components produced by this technique were investigated. In general, it was found that the amount of porosity is inversely proportional to the initial concentration of metal powder in the PIM feedstock. Likewise, average pore size displays a similar relationship with powder loading.

  2. Alkaline solution/binder ratio as a determining factor in the alkaline activation of aluminosilicates

    SciTech Connect (OSTI)

    Ruiz-Santaquiteria, C.; Fernandez-Jimenez, A.; Palomo, A.

    2012-09-15

    This study investigates the effect of the alkaline solution/binder (S/B) ratio on the composition and nanostructure of the reaction products generated in the alkaline activation of aluminosilicates. The experiments used two mixtures of fly ash and dehydroxylated white clay and for each of these, varying proportions of the solution components. The alkali activator was an 8 M NaOH solution (with and without sodium silicate) used at three S/B ratios: 0.50, 0.75 and 1.25. The {sup 29}Si, {sup 27}Al MAS NMR and XRD characterisation of the reaction products reveal that for ratios nearest the value delivering suitable paste workability, the reaction-product composition and structure depend primarily on the nature and composition of the starting materials and the alkaline activator used. However, when an excess alkaline activator is present in the system, the reaction products tend to exhibit SiO{sub 2}/Al{sub 2}O{sub 3} ratios of approximately 1, irrespective of the composition of the starting binder or the alkaline activator.

  3. PBXN-9 Ignition Kinetics and Deflagration Rates

    SciTech Connect (OSTI)

    Glascoe, E; Maienschein, J; Burnham, A; Koerner, J; Hsu, P; Wemhoff, A

    2008-04-24

    The ignition kinetics and deflagration rates of PBXN-9 were measured using specially designed instruments at LLNL and compared with previous work on similar HMX based materials. Ignition kinetics were measured based on the One Dimensional Time-to-Explosion combined with ALE3D modeling. Results of these experiments indicate that PBXN-9 behaves much like other HMX based materials (i.e. LX-04, LX-07, LX-10 and PBX-9501) and the dominant factor in these experiments is the type of explosive, not the type of binder/plasticizer. In contrast, the deflagration behavior of PBXN-9 is quite different from similar high weight percent HMX based materials (i.e LX-10, LX-07 and PBX-9501). PBXN-9 burns in a laminar manner over the full pressure range studied (0-310 MPa) unlike LX-10, LX-07, and PBX-9501. The difference in deflagration behavior is attributed to the nature of the binder/plasticizer alone or in conjunction with the volume of binder present in PBXN-9.

  4. Pigments with or without organic binder? A survey of wall painting techniques during Antiquity

    SciTech Connect (OSTI)

    Walter, P.

    1996-01-01

    The identification of ancient artistic techniques is based on laboratory studies and, for historical cases, also on literary sources. An analytical approach using the techniques of physical chemistry reveals the technical expertise of the artists, right at the dawn of art. In the case of prehistoric parietal art, we show that the artists prepared their pigments with different ground and mixed minerals. They applied their material onto the wall and the particles remained embedded in the superficial calcite layer. Later, the prehistoric people prepared a real paint with the proper pigment, an extender and an organic binder to fix the paint on the wall. During Antiquity, new techniques appear. The paint is applied to the natural or artificial wall and is executed, either directly or on a previously applied plaster. The aim of this paper is to describe the evolution of the techniques. The underlying chemistry provides some interesting clues on the technical choices. {copyright} {ital 1996 American Institute of Physics.}

  5. Maggi Kelly -CV p. 1 Maggi Kelly

    E-Print Network [OSTI]

    Silver, Whendee

    Resources Associate. NOAA-NMFS Lab, Beaufort, NC 1996 Ph.D. Department of Geography. University of Colorado, Boulder, Colorado 1991 M.A. Department of Geography

  6. The importance of the glass transition temperature in relation to the low-temperature fracture resistance of asphalt and sulphlex pavement binders 

    E-Print Network [OSTI]

    Smith, Douglas Lee

    1985-01-01

    dilatometer was fabricated for use in the determination of the glass trans1ti on temperature of asphalt and plasticized sulfur (Sulphlex) pavement binders. A total of 11 materials were examined including seven Sul phlex binders, a blend of two Sulphlex.... Ouartz Tube Dilatometer . Df fferential Scanning Calorimetry . IV EXPERIMENTAL PRDCEOURE. Materials Selection . . Di 1atometri c Measurements V RESULTS Vi scoel asti c Justi f i cat i on. Experimental Results. Statistical Analysis. VI CONCLUSIONS...

  7. PathBinderH: Taxonomy-Sensitive Literature Access Bioinformatics, 21(10) (May 2005), pp. 2560-2562.

    E-Print Network [OSTI]

    Berleant, Daniel

    ,2,5 , A. Fulmer8 , and P. S. Schnable2,4,6,9 1 Department of Electrical and Computer Engineering; 2 Iowa at the Department of Mathematics and Statistics, University of Guelph, Ontario, Canada N1G 2W1 #12;Path.plantgenomics.iastate.edu/PathBinderH. Source code and databases on request. Contact: berleant@iastate.edu Supplementary information: A tutorial

  8. X-ray microtomography shows pore structure and tortuosity in alkali-activated binders

    SciTech Connect (OSTI)

    Provis, John L.; Myers, Rupert J.; White, Claire E.; Rose, Volker; Deventer, Jannie S.J. van

    2012-06-15

    Durability of alkali-activated binders is of vital importance in their commercial application, and depends strongly on microstructure and pore network characteristics. X-ray microtomography ({mu}CT) offers, for the first time, direct insight into microstructural and pore structure characteristics in three dimensions. Here, {mu}CT is performed on a set of sodium metasilicate-activated fly ash/slag blends, using a synchrotron beamline instrument. Segmentation of the samples into pore and solid regions is then conducted, and pore tortuosity is calculated by a random walker method. Segmented porosity and diffusion tortuosity are correlated, and vary as a function of slag content (slag addition reduces porosity and increases tortuosity), and sample age (extended curing gives lower porosity and higher tortuosity). This is particularly notable for samples with {>=} 50% slag content, where a space-filling calcium (alumino)silicate hydrate gel provides porosity reductions which are not observed for the sodium aluminosilicate ('geopolymer') gels which do not chemically bind water of hydration.

  9. INCLINED PLATE SETTLERS TO TREAT STORMWATER SOLIDS Christopher D. Roenning1, Kelly A Steele2,1, James Elligson3,1, J. Bradley Mikula4,1, Shirley Clark1

    E-Print Network [OSTI]

    Clark, Shirley E.

    INCLINED PLATE SETTLERS TO TREAT STORMWATER SOLIDS Christopher D. Roenning1, Kelly A Steele2. Introduction Sedimentation preferred treatment method for removing solids from stormwater runoff, either with solids in stormwater of a particular size (Figure 1: pollutant load vs. particle size). Stokes' Law

  10. Kelly Doley Penelope Benton

    E-Print Network [OSTI]

    New South Wales, University of

    seating, COFA students enrolled in the Permaculture Design Winter elec- tive have been busy creating

  11. Kelly Doley Penelope Benton

    E-Print Network [OSTI]

    New South Wales, University of

    menstrual, if I see a really incredible gig or exhibi- tion or drink lots of coffee or heaps of booze

  12. Kelly Doley Penelope Benton

    E-Print Network [OSTI]

    New South Wales, University of

    , prose, art, ideas and recipes. CONTENTS 3. New COFA zine MANIFESTO, Boo Patrick 6. Working with Pip&Pop in progress Pip & Pop photo by Rose Jurd LOGO DESIGN Kiera Chevell PRINTING Arc Office @ COFA THANKS Arc with fabulous fame, working on the Fashion Week set for local designers Romance Was Born, with WA artists Pip&Pop

  13. Rate Schedules

    Broader source: Energy.gov [DOE]

    One of the major responsibilities of Southeastern is to design, formulate, and justify rate schedules. Repayment studies prepared by the agency determine revenue requirements and appropriate rate...

  14. High-discharge-rate lithium ion battery

    SciTech Connect (OSTI)

    Liu, Gao; Battaglia, Vincent S; Zheng, Honghe

    2014-04-22

    The present invention provides for a lithium ion battery and process for creating such, comprising higher binder to carbon conductor ratios than presently used in the industry. The battery is characterized by much lower interfacial resistances at the anode and cathode as a result of initially mixing a carbon conductor with a binder, then with the active material. Further improvements in cycleability can also be realized by first mixing the carbon conductor with the active material first and then adding the binder.

  15. Production of low-sulfur binder pitch from high-sulfur Illinois coals. Technical report, September 1--November 30, 1994

    SciTech Connect (OSTI)

    Knight, R.A. [Inst. of Gas Technology, Chicago, IL (United States)

    1994-12-31

    The objective of this project is to produce electrode binder pitch with sulfur content below 0.6 wt% from high-sulfur Illinois coal mild gasification liquids. In this project, two approaches to sulfur reduction are being explored in conjunction with thermocracking: (1) the use of conventionally cleaned coal with low ({approximately}1%) sulfur as a mild gasification feedstock, and (2) direct biodesulfurization of the liquids prior to thermocracking. In Case 1, the crude pitch is being produced by mild gasification of IBC-109 coal in an existing IGT bench-scale reactor, followed by distillation of the scrubbing solvent and light-to-middle oils to isolate the crude pitch. In Case 2, the crude pitch for biodesulfurization is the same material previously studied, which was obtained from Illinois No. 6 coal tests conducted in the IGT mild gasification PRU in 1990. Biodesulfurization is to be performed by contacting the pitch with Rhodococcus Rhodochrous either as live cultures or in the form of concentrated biocatalyst. Following preparation of the crude pitches, pitch upgrading experiments are to be conducted in a continuous flash thermocracker (FTC) constructed in previous ICCI-sponsored studies. The finished pitch is then characterized for physical and chemical properties (density, softening point, QI, TI, coking value, and elemental composition), and compared to typical specifications for binder pitches. This quarter, 45 kg of IBC-109 coal was obtained and sized to 40 x 80 mesh for mild gasification. Laboratory experiments were conducted to identify means of dispersing or emulsifying pitch in water to render is accessible to biocatalysts, and exploratory desulfurization tests on one-gram pitch samples were begun.

  16. Incorporation of reactive magnesia and quicklime in sustainable binders for soil stabilisation

    E-Print Network [OSTI]

    Gu, Kai; Jin, Fei; Al-Tabbaa, Abir; Shi, Bin; Liu, Chun; Gao, Lei

    2015-05-27

    strength, volume stability, durability and permeability. The primary mechanism of soil stabilisation with PC is through the hydration of PC which leads to the formation of cementitious calcium silicate hydrates (C-S-H), calcium aluminate hydrates (C... which leads to expansion and cracking of cement and concrete through the delayed hydration. Reactive MgOs have much higher reactivity than dead burned MgO and hence faster hydration rate. On the other hand, given the different origins and production...

  17. Binder free three-dimensional sulphur/few-layer graphene foam cathode with enhanced high-rate capability for rechargeable lithium sulphur batteries

    E-Print Network [OSTI]

    Xi, Kai; Kidambi, Piran R.; Chen, Renjie; Gao, Chenlong; Peng, Xiaoyu; Ducati, Caterina; Hofmann, Stephan; Kumar, R. Vasant

    2014-03-04

    ( V v s. Li + /L i) Capacity (mAh g-1-sulfur) Charge Discharge (a) 800 mA/g 0 10 20 30 40 50 0 200 400 600 800 1000 1200 D isc ha rg e ca pa ci ty (m A hg -1 -s ul fu r) Cycle number charge discharge 0 20 40 60 80 100 120 800 mA/g C ou lo... m bi c Ef fic ie nc y (% )(b) 0 100 200 300 400 0 300 600 900 1200 D isc ha rg e ca pa ci ty (m A h g-1 -s ul fu r) Cycle number charge discharge (c) 0 20 40 60 80 100 120 3200 mA/g C ou lo m bi c E ffi ci en cy (% ) Po te nt ia l ( V v s...

  18. Kelly Scientific Resources Kelly Scientific Resources yy BIOTECHNOLOGY DRUG &

    E-Print Network [OSTI]

    Puglisi, Joseph

    for a wide variety of scientific and clinical research positions. KSR is a trusted career advisor, guiding is a $92 Billion Dollar Industry Customer Uses for an Agencyg y · Strictly Head Count · Special Projects staffing supplier in the world * ­ Recruiting Scientific and Clinical Research professionals since 1995

  19. Kellie R. Aarons Ibrahim Abubakar

    E-Print Network [OSTI]

    Frantz, Kyle J.

    . Bechtel-Hall Amanda L. Beck Beth C. Belanger Rachel D. Bell Kyle S. Bennett Tierra M. Benton Juliana Caitlin C. Bradley Jonathan C. Brady Nicole Brancato Hope C. Brewer Emily L. Brincks Jo E. Brooks Jesse D

  20. Nadiyah Aamer Kellie R. Aarons

    E-Print Network [OSTI]

    Frantz, Kyle J.

    -Rangel Caitlin A. Barrow Sauveur M. Barry Melissa N. Bass Hannah N. Basta Zachary A. Bates Carla M. Bazemore- Colclough Gaea Bear-Sartor Beth C. Belanger Katryna M. Bell Alex D. Ben-Dor Molly A. Bengochea Daniela

  1. Curriculum Vitae Kelly T. Morgan

    E-Print Network [OSTI]

    Jawitz, James W.

    , improved production methods, and evaluation of new citrus selections. Developed automated soil water setup, treatments, and data collection including horticultural evaluation, nutritional status analysis water uptake data collection and analysis using neutron probes, tensiometers, and capacitance sensors

  2. Eukaryotic Gene Prediction Kelli Davies

    E-Print Network [OSTI]

    -scale genome sequencing has revolutionized the field of genetics and biology. Sequencing projects require sophisticated computational analysis to manage vast collections of data. Scientists first sequenced a genome, coding genes comprise 95% of the genome.1 Since then, numerous prokaryotic and eukaryotic genomes have

  3. Kelly Visconti | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergyTher i nAand DOE Safety Standards Implementation JulyThe Orlando Science

  4. FRN and Rate Schedules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Doing Business Skip navigation links Financial Information Financial Public Processes Asset Management Cost Verification Process Rate Cases BP-16 Rate Case OS-14 Rate Case FRN...

  5. FRN & Rate Schedules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Doing Business Skip navigation links Financial Information Financial Public Processes Asset Management Cost Verification Process Rate Cases BP-16 Rate Case OS-14 Rate Case FRN...

  6. Chlorite Dissolution Rates

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Carroll, Susan

    2013-07-01

    Spreadsheets provides measured chlorite rate data from 100 to 300C at elevated CO2. Spreadsheet includes derived rate equation.

  7. Chlorite Dissolution Rates

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Carroll, Susan

    Spreadsheets provides measured chlorite rate data from 100 to 300C at elevated CO2. Spreadsheet includes derived rate equation.

  8. 2004 Rate Adjustments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for Transmission and Ancillary Services Federal Register Notice -- Rate Order WAPA-141: Notice of Extension of Formula Rates for Transmission and Ancillary Services If you have any...

  9. Rate Schedule CPP-2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    points established by contract, in accordance with approved policies and procedures. Formula Rate: The formula rate for CPP includes three components: Component 1: The customer...

  10. Lesson 22 Related Rates

    E-Print Network [OSTI]

    2013-10-11

    Oct 11, 2013 ... A spherical weather balloon is being inflated with helium at a rate of 82 cubic meters per minute. Find the rate at which its radius is increasing.

  11. Naughton's related rates problems

    E-Print Network [OSTI]

    dominic

    2013-02-25

    Related rates (1). (1) Oil spills from a rupture container in a circular pattern whose radius increases at a rate of 2 ft/s. How fast is the area of the oil spill increasing ...

  12. "Magic Angle Precession" Bernd Binder

    E-Print Network [OSTI]

    Binder, Bernd

    by geometric phases, which are induced by high- speed relativistic rotations and are relevant to propulsion, quark, confinement, heavy nuclei, Sommerfeld, fine structure, propulsion, SO(3), nonlinear, chaotic maps in the vicinity of a magnetic monopole or singularity (Dirac, 1931) that could be located on the tip

  13. Resonant thermonuclear reaction rate

    SciTech Connect (OSTI)

    Haubold, H.J.; Mathai, A.M.

    1986-08-01

    Basic physical principles for the resonant and nonresonant thermonuclear reaction rates are applied to find their standard representations for nuclear astrophysics. Closed-form representations for the resonant reaction rate are derived in terms of Meijer's G-italic-function. Analytic representations of the resonant and nonresonant nuclear reaction rates are compared and the appearance of Meijer's G-italic-function is discussed in physical terms.

  14. LCC Guidance Rates

    Office of Energy Efficiency and Renewable Energy (EERE)

    Notepad text file provides the LCC guidance rates in a numbered format for the various regions throughout the U.S.

  15. Power Rate Cases (pbl/rates)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeedingProgram Guidelines This document w w w.pv - te ch.orgPower PlantRates >

  16. Power Rates Announcements (pbl/rates)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeedingProgram Guidelines This document w w w.pv - te ch.orgPower PlantRates >

  17. Rates Meetings and Workshops (pbl/rates)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMassR&D100 Winners * Impacts on GlobalRachel2RateCaseElements Sign In About | FY

  18. Previous Power Rates (rates/current)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II) by Carbon-Rich Matrices in Hydrothermal PlumesPress1,Previous EventsRates

  19. Effective Rate Period

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Regulation and Frequency Response DollarsKW-month 4.56 CV-RFS4 Spinning Reserve The formula rate for spinning reserve service is the price consistent with the California...

  20. Effective Rate Period

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Frequency Response DollarsKW-month 3.98 4.17 CV-RFS4 Spinning Reserve The formula rate for spinning reserve service is the price consistent with the California...

  1. Effective Rate Period

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Frequency Response DollarsKW-month 4.17 4.56 CV-RFS4 Spinning Reserve The formula rate for spinning reserve service is the price consistent with the California...

  2. 2012 Transmission Rate Schedules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for HLH and LLH. 2. OTHER RATE PROVISIONS a. BPA Incremental Cost BPA's incremental cost will be based on an hourly energy index in the Pacific Northwest. If no adequate...

  3. On Thermonuclear Reaction Rates

    E-Print Network [OSTI]

    H. J. Haubold; A. M. Mathai

    1996-12-02

    Nuclear reactions govern major aspects of the chemical evolution od galaxies and stars. Analytic study of the reaction rates and reaction probability integrals is attempted here. Exact expressions for the reaction rates and reaction probability integrals for nuclear reactions in the case of nonresonant, modified nonresonant, screened nonresonant and resonant cases are given. These are expressed in terms of H-functions, G-functions and in computable series forms. Computational aspects are also discussed.

  4. Kellie R. Aarons Autumn M. Abraham

    E-Print Network [OSTI]

    Frantz, Kyle J.

    . Beck Barrie L. Bedasee Darlene E. Belen Katryna M. Bell Gabriel E. Beltran Joseph A. Bennett Tierra M Shannon L. Borum Ariyana Bozzorg Jennifer K. Bradberry Caitlin C. Bradley Jonathan C. Brady Payal R

  5. Kellie R. Aarons Abdilatif A. Abdulhakim

    E-Print Network [OSTI]

    Frantz, Kyle J.

    -Valdivieso Valeria A. Barkovskii Juan A. Barragan Caitlin A. Barrow Hortense T. Baya Kristin A. Bazille Zachary D. Beasley Margaret C. Beaver Arielle B. Beer Beth C. Belanger Sarah E. Bell Molly A. Bengochea Paulita

  6. Jeffrey D. Kelly Honeywell Process Solutions, Canada

    E-Print Network [OSTI]

    Grossmann, Ignacio E.

    flows through the system. Usually refers to raw materials, intermediate and final products · Graphically-Task-Network (STN) ­ Pantelides (1994) ­ "Resources" · Non-renewable resources (e.g.: raw materials, intermediate of Manufacturing · Types of Production Objects · Logistics Modeling · Quality Modeling · Industrial Cases

  7. Microsoft Word - 04062011_Kelly Testimony _final_ _3_

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the productivity and reduce the cost of biochemical processes using engineered yeast, bacteria, and other organisms. The President recently set a goal of reducing petroleum imports...

  8. 1JUNE -SEPTEMBER 2012 Sophomore Kelly

    E-Print Network [OSTI]

    Cook, Greg

    Forest communication professor and film critic Mary Dalton and "Hoop Dreams" producer and documentary film professor Peter Gilbert were both interviewed for their Oscar- winner predictions. MARCH 9, 2015

  9. Anita M. Kelly and Sathyanand Kumaran

    E-Print Network [OSTI]

    Kane, Andrew S.

    in spring Occurs in ponds that have not been drained in 2 years or more The older ponds have a good bloom on them. Fish apparently there one day #12;3 #12;4 To determine if ponds with high hydrogen sulfide concentrations had

  10. Invasive Pathogens By: Kelly Moffett, Ryan Crawford,

    E-Print Network [OSTI]

    Schweik, Charles M.

    ;Literature Review Invasion Pathways of Terrestrial Plant-Inhabiting Fungi (Mary E. Palm and Amy Y Rossman Collected data on Native/Introduced areas Introduction pathways Time of Introduction Analyzed Types of Invasive Pathogens Introduction type Accidental pathways Resources Used Internet databases, including

  11. Sean Colbert-Kelly and Daniel Phillips

    E-Print Network [OSTI]

    2012-12-27

    where ks and kb represent the two dimensional splay and bend moduli for the film ... number of structural properties that lead to the first main result of the paper.

  12. John E. Kelly | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergy A plug-inPPLforLDRDEnergy CopyrightsRoom 1E-245Committee on Commerce |U.S.Chu

  13. JH Kelly LLC Ethanol | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX E LISTStar2-0057-EAInvervar Hydro Jump to: navigation,Jump to:Corp Jump to:

  14. kelly rose | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust,Field-effectWorkingLosThe 26th AnnualHistoryM aterials S cience ajwangMethodthekcho

  15. John E. Kelly | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on DeliciousMathematicsEnergyInterested Parties - WAPA Public CommentInverted Attic9: What(CSC)JobCommitteeJohn

  16. Rotational rate sensor

    DOE Patents [OSTI]

    Hunter, Steven L. (Livermore, CA)

    2002-01-01

    A rate sensor for angular/rotational acceleration includes a housing defining a fluid cavity essentially completely filled with an electrolyte fluid. Within the housing, such as a toroid, ions in the fluid are swept during movement from an excitation electrode toward one of two output electrodes to provide a signal for directional rotation. One or more ground electrodes within the housing serve to neutralize ions, thus preventing any effect at the other output electrode.

  17. "A New Rapid Tooling Technique and Its Special Binder Study," Jack Zhou and Z. He, Journal of Rapid Prototyping, Vol. 5, No. 2, pp. 82-88, 1999.

    E-Print Network [OSTI]

    Zhou, Jack

    as a process that allows a tool for injection molding or die casting operations to be manufactured quickly rate due to the thick wall of the mold and the bad conductivity of the investment materials. Solid mold will undergo greater thermal expansion and contraction during the firing and cooling cycles, therefore

  18. Current Power Rates

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would like submit theCovalent Bonding in ActinideRail betweenProtectionCurrentJobPower-Rates

  19. Rate Case Elements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMassR&D100 Winners * Impacts on GlobalRachel2RateCaseElements Sign In About | Careers |

  20. Rate Design and Renewables

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMassR&D100 Winners * Impacts on GlobalRachel2RateCaseElements Sign In About | Careers

  1. Energy Management Through Innovative Rates 

    E-Print Network [OSTI]

    Williams, M. L.

    1982-01-01

    of energy efficiency in the industrial sector and specific rate design alternatives for doing so....

  2. National Utility Rate Database: Preprint

    SciTech Connect (OSTI)

    Ong, S.; McKeel, R.

    2012-08-01

    When modeling solar energy technologies and other distributed energy systems, using high-quality expansive electricity rates is essential. The National Renewable Energy Laboratory (NREL) developed a utility rate platform for entering, storing, updating, and accessing a large collection of utility rates from around the United States. This utility rate platform lives on the Open Energy Information (OpenEI) website, OpenEI.org, allowing the data to be programmatically accessed from a web browser, using an application programming interface (API). The semantic-based utility rate platform currently has record of 1,885 utility rates and covers over 85% of the electricity consumption in the United States.

  3. Bubble growth rates in boiling

    E-Print Network [OSTI]

    Griffith, P.

    1956-01-01

    The conditions determining the growth rate of a bubble on a surface in boiling are considered and a mathematical model framed in the light of these conditions. The growth rate is then calculated for bubbles growing under ...

  4. 2007 Wholesale Power Rate Schedules : 2007 General Rate Schedule Provisions.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    2006-11-01

    This schedule is available for the contract purchase of Firm Power to be used within the Pacific Northwest (PNW). Priority Firm (PF) Power may be purchased by public bodies, cooperatives, and Federal agencies for resale to ultimate consumers, for direct consumption, and for Construction, Test and Start-Up, and Station Service. Rates in this schedule are in effect beginning October 1, 2006, and apply to purchases under requirements Firm Power sales contracts for a three-year period. The Slice Product is only available for public bodies and cooperatives who have signed Slice contracts for the FY 2002-2011 period. Utilities participating in the Residential Exchange Program (REP) under Section 5(c) of the Northwest Power Act may purchase Priority Firm Power pursuant to the Residential Exchange Program. Rates under contracts that contain charges that escalate based on BPA's Priority Firm Power rates shall be based on the three-year rates listed in this rate schedule in addition to applicable transmission charges. This rate schedule supersedes the PF-02 rate schedule, which went into effect October 1, 2001. Sales under the PF-07 rate schedule are subject to BPA's 2007 General Rate Schedule Provisions (2007 GRSPs). Products available under this rate schedule are defined in the 2007 GRSPs. For sales under this rate schedule, bills shall be rendered and payments due pursuant to BPA's 2007 GRSPs and billing process.

  5. Commercial Building Asset Rating Program

    Broader source: Energy.gov [DOE]

    Slides from a Commercial Building Initiative webinar outlining the Commercial Building Asset Rating Program on August 23, 2011.

  6. Methane oxidation rates by AMS

    E-Print Network [OSTI]

    Pack, M; Heintz, M; ReeburGh, WS; Trumbore, SE; Valentine, DL; Xu, X

    2009-01-01

    second case. Number of cases Methane oxidation rates by AMSIn the marine environment methane (CH 4 ) oxidation consumes

  7. Wholesale Power Rate Schedules | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Rate Schedules Wholesale Power Rate Schedules Wholesale Power Rate Schedules October 1, 2012 ALA-1-N Wholesale Power Rate Schedule Area: PowerSouth Energy Cooperative System:...

  8. LMS SUBSCRIPTION RATES & NOTES 2014/15 SUBSCRIPTION RATES

    E-Print Network [OSTI]

    1 LMS SUBSCRIPTION RATES & NOTES 2014/15 SUBSCRIPTION RATES LMS membership subscription: £ US.00 Associate membership 16.00 32.00 Free membership (see note 2) Print only Online only Print & online* LMS, or are unemployed or otherwise in hardship. Contact membership@lms.ac.uk to enquire further. #12;LMS PUBLICATIONS 4

  9. LMS SUBSCRIPTION RATES & NOTES 2013/14 SUBSCRIPTION RATES

    E-Print Network [OSTI]

    1 LMS SUBSCRIPTION RATES & NOTES 2013/14 SUBSCRIPTION RATES LMS membership subscription: £ US.00 Associate membership 15.00 30.00 Free membership (see note 2) Print only Online only Print & online* LMS, or are unemployed or otherwise in hardship. Contact membership@lms.ac.uk to enquire further. #12;LMS PUBLICATIONS 4

  10. Upper Great Plains Rates information

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3, 2014 (112 KB .pdf) FRN Notice of Proposed Transmission and Ancillary Services Formula Rates November 3, 2014 (93 KB .pdf) SPP Membership Information Integrated System (IS)...

  11. Sustainable Building Rating Systems Summary

    SciTech Connect (OSTI)

    Fowler, Kimberly M.; Rauch, Emily M.

    2006-07-01

    The purpose of this document is to offer information that could be used to compare and contrast sustainable building rating systems.

  12. High Rate and High Capacity Li-Ion Electrodes for Vehicular Applications

    SciTech Connect (OSTI)

    Dillon, A. C.

    2012-01-01

    Significant advances in both energy density and rate capability for Li-ion batteries are necessary for implementation in electric vehicles. We have employed two different methods to improve the rate capability of high capacity electrodes. For example, we previously demonstrated that thin film high volume expansion MoO{sub 3} nanoparticle electrodes ({approx}2 {micro}m thick) have a stable capacity of {approx}630 mAh/g, at C/2 (charge/dicharge in 2 hours). By fabricating thicker conventional electrodes, an improved reversible capacity of {approx}1000 mAh/g is achieved, but the rate capability decreases. To achieve high-rate capability, we applied a thin Al{sub 2}O{sub 3} atomic layer deposition coating to enable the high volume expansion and prevent mechanical degradation. Also, we recently reported that a thin ALD Al{sub 2}O{sub 3} coating can enable natural graphite (NG) electrodes to exhibit remarkably durable cycling at 50 C. Additionally, Al{sub 2}O{sub 3} ALD films with a thickness of 2 to 4 {angstrom} have been shown to allow LiCoO{sub 2} to exhibit 89% capacity retention after 120 charge-discharge cycles performed up to 4.5 V vs. Li/Li{sup +}. Capacity fade at this high voltage is generally caused by oxidative decomposition of the electrolyte or cobalt dissolution. We have recently fabricated full cells of NG and LiCoO{sub 2} and coated both electrodes, one or the other electrode as well as neither electrode. In creating these full cells, we observed some surprising results that lead us to obtain a greater understanding of the ALD coatings. In a different approach we have employed carbon single-wall nanotubes (SWNTs) to synthesize binder-free, high-rate capability electrodes, with 95 wt.% active materials. In one case, Fe{sub 3}O{sub 4} nanorods are employed as the active storage anode material. Recently, we have also employed this method to demonstrate improved conductivity and highly improved rate capability for a LiNi{sub 0.4}Mn{sub 0.4}Co{sub 0.2}O{sub 2} cathode material. Raman spectroscopy was employed to understand how the SWNTs function as a highly flexible conductive additive.

  13. Innovative Rates Program. Final report

    SciTech Connect (OSTI)

    Not Available

    1982-06-21

    Title II of the Energy Conservation and Production Act (ECPA) as amended by the Public Utility Regulatory Policies Act (PURPA) provided financial assistance to state utility regulatory commissions, nonregulated electric utilities, and the Tennessee Valley Authority through the Innovative Rates Program. The financial assistance was to be used to plan or carry out electric utility regulatory rate reform initiatives relating to innovative rate structures that encourage conservation of energy, electric utility efficiency and reduced costs, and equitable rates to consumers. The Federal and local objectives of the project are described. Activities planned and accomplishments are summarized for the following: project management, data collection, utility bill evaluation, billing enclosure/mailing evaluation, media program evaluation, display evaluation, rate study sessions evaluation, speakers bureau evaluation, and individual customer contacts. A timetable/milestone chart and financial information are included. (MHR)

  14. Rate Adjustments and Public Involvement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Letter to South Texas Electric Coop., Inc requesting an extension of the existing rate formula FalconAmistad WAPA-143 FERC Approval FalconAmistad Published WAPA-143 Falcon...

  15. Tier 2 Vintage Rate Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    period FY2015 through 2028. Customers have a diversification right to limit the amount of power they purchase at the Load Growth rate in future years with notice provided by...

  16. Asset Prices and Exchange Rates

    E-Print Network [OSTI]

    Pavlova, Anna

    2003-08-01

    This paper develops a simple two-country, two-good model, in which the real exchange rate, stock and bond prices are jointly determined. The model predicts that ...

  17. Asset Prices and Exchange Rates

    E-Print Network [OSTI]

    Pavlova, Anna

    2004-11-30

    This paper develops a simple two-country, two-good model, in which the real exchange rate, stock and bond prices are jointly determined. The model predicts that stock market prices are correlated ...

  18. High repetition rate fiber lasers

    E-Print Network [OSTI]

    Chen, Jian, Ph. D. Massachusetts Institute of Technology

    2009-01-01

    This thesis reports work in high repetition rate femtosecond fiber lasers. Driven by the applications including optical arbitrary waveform generation, high speed optical sampling, frequency metrology, and timing and frequency ...

  19. High compression rate text summarization

    E-Print Network [OSTI]

    Branavan, Satchuthananthavale Rasiah Kuhan

    2008-01-01

    This thesis focuses on methods for condensing large documents into highly concise summaries, achieving compression rates on par with human writers. While the need for such summaries in the current age of information overload ...

  20. TECHNICAL NOTE FISH PROTEINS AS BINDERS

    E-Print Network [OSTI]

    products . Recently in th meat and poultry industry, there has been interest in binding tog th r pieces and storage at temperatures above freezing . The following describes some of the re- search on the use of fish various flavoring agents such as ocean quahogs, ,Iaine shrimp, and crab meat. All these were highly

  1. Working with An educational resource binder for

    E-Print Network [OSTI]

    Radcliffe, David

    Thermal Pollution of Water ............................................................................136

  2. Nanoscale Heterostructures and Thermoplastic Resin Binders: Novel

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankADVANCED MANUFACTURING OFFICESpecialAPPENDIX FOrigin ofAllenDepartmentNYSERDANanolubricantsLithium-Ion

  3. Coal Transportation Rate Sensitivity Analysis

    Reports and Publications (EIA)

    2005-01-01

    On December 21, 2004, the Surface Transportation Board (STB) requested that the Energy Information Administration (EIA) analyze the impact of changes in coal transportation rates on projected levels of electric power sector energy use and emissions. Specifically, the STB requested an analysis of changes in national and regional coal consumption and emissions resulting from adjustments in railroad transportation rates for Wyoming's Powder River Basin (PRB) coal using the National Energy Modeling System (NEMS). However, because NEMS operates at a relatively aggregate regional level and does not represent the costs of transporting coal over specific rail lines, this analysis reports on the impacts of interregional changes in transportation rates from those used in the Annual Energy Outlook 2005 (AEO2005) reference case.

  4. Fast repetition rate (FRR) flasher

    DOE Patents [OSTI]

    Kolber, Z.; Falkowski, P.

    1997-02-11

    A fast repetition rate (FRR) flasher is described suitable for high flash photolysis including kinetic chemical and biological analysis. The flasher includes a power supply, a discharge capacitor operably connected to be charged by the power supply, and a flash lamp for producing a series of flashes in response to discharge of the discharge capacitor. A triggering circuit operably connected to the flash lamp initially ionizes the flash lamp. A current switch is operably connected between the flash lamp and the discharge capacitor. The current switch has at least one insulated gate bipolar transistor for switching current that is operable to initiate a controllable discharge of the discharge capacitor through the flash lamp. Control means connected to the current switch for controlling the rate of discharge of the discharge capacitor thereby to effectively keep the flash lamp in an ionized state between successive discharges of the discharge capacitor. Advantageously, the control means is operable to discharge the discharge capacitor at a rate greater than 10,000 Hz and even up to a rate greater than about 250,000 Hz. 14 figs.

  5. MEDICAL RATES for Active Employees

    E-Print Network [OSTI]

    New Mexico, University of

    -time, your base salary is calculated on the full-time equivalent. For example, if you are at an appointment percentage of 50% and earn $12,000 per year, your base salary is $24,000 and UNM would contribute 40%. UNM Health-Bi-Weekly Rates Annualized Salary $34,999 and below Annualized Salary $35,000 - $49,999 Annualized

  6. Fast repetition rate (FRR) flasher

    DOE Patents [OSTI]

    Kolber, Zbigniew (Shoreham, NY); Falkowski, Paul (Stony Brook, NY)

    1997-02-11

    A fast repetition rate (FRR) flasher suitable for high flash photolysis including kinetic chemical and biological analysis. The flasher includes a power supply, a discharge capacitor operably connected to be charged by the power supply, and a flash lamp for producing a series of flashes in response to discharge of the discharge capacitor. A triggering circuit operably connected to the flash lamp initially ionizes the flash lamp. A current switch is operably connected between the flash lamp and the discharge capacitor. The current switch has at least one insulated gate bipolar transistor for switching current that is operable to initiate a controllable discharge of the discharge capacitor through the flash lamp. Control means connected to the current switch for controlling the rate of discharge of the discharge capacitor thereby to effectively keep the flash lamp in an ionized state between Successive discharges of the discharge capacitor. Advantageously, the control means is operable to discharge the discharge capacitor at a rate greater than 10,000 Hz and even up to a rate greater than about 250,000 Hz.

  7. Electric Rate Alternatives to Cogeneration 

    E-Print Network [OSTI]

    Sandberg, K. R. Jr.

    1988-01-01

    ALTERNATIVES TO COGENERATION" K. R. SANDBERG, JR. INDUSTRIAL ACCOUNTS MANAGER - TEXAS GULF STATES UTILITIES COMPANY BEAUMONT, TEXAS ABSTRACT This paper discusses electric rate slternatives to cogeneration for the industrisl customer and attempts... electricity to municipalities and rural electric cooperatives in both Texas and Louisiana. In Baton Rouge. GSU supplies steam and electricity to a large industrial customer through a cogeneration facility that the company has had in operation since...

  8. Cooling rate, heating rate and aging effects in glassy water

    E-Print Network [OSTI]

    Nicolas Giovambattista; H. Eugene Stanley; Francesco Sciortino

    2004-03-03

    We report a molecular dynamics simulation study of the properties of the potential energy landscape sampled by a system of water molecules during the process of generating a glass by cooling, and during the process of regenerating the equilibrium liquid by heating the glass. We study the dependence of these processes on the cooling/heating rates as well as on the role of aging (the time elapsed in the glass state). We compare the properties of the potential energy landscape sampled during these processes with the corresponding properties sampled in the liquid equilibrium state to elucidate under which conditions glass configurations can be associated with equilibrium liquid configurations.

  9. WP-07 Power Rate Case (rates/ratecases)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservationBio-Inspired SolarAbout /Two0Photos and Videos Videos Re-EntryApproval OMB No.:Rates

  10. October 1996 - September 2001 Wholesale Power Rates (rates/previous)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access toOctober 1996 - September 2001 The rates BPA charges for power are

  11. October 2001 - March 2002 Power Rates (rates/previous)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access toOctober 1996 - September 2001 The rates BPA charges for power

  12. October 2001 - September 2006 Wholesale Power Rates (rates/previous)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access toOctober 1996 - September 2001 The rates BPA charges for power1 -

  13. October 2002 - March 2003 Power Rates (rates/previous)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access toOctober 1996 - September 2001 The rates BPA charges for power1

  14. October 2003 - March 2004 Power Rates (rates/previous)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access toOctober 1996 - September 2001 The rates BPA charges for power13 -

  15. October 2004 - March 2005 Power Rates (rates/previous)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access toOctober 1996 - September 2001 The rates BPA charges for power13

  16. October 2005 - March 2006 Power Rates (rates/previous)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access toOctober 1996 - September 2001 The rates BPA charges for power135

  17. WP-07 Rate Case Workshops (rates/meetings)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust,Field-effectWorking WithTelecentricN A 035(92/02) nerg *415,Rates > Meetings &

  18. Rate Schedule CV-SPR4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    that is available immediately to serve load and is synchronized with the power system. Formula Rate: The formula rate for spinning reserve includes three components: Component 1:...

  19. Rate Schedule CV-SUR4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    within the first 10 minutes to take load and is synchronized with the power system. Formula Rate: The formula rate for supplemental reserve service includes three components:...

  20. Rate Schedule COTP-T3

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and system control and dispatch service needed to support the transmission service. Formula Rate: The formula rate for COTP firm and non-firm PTP transmission service includes...

  1. Rate Schedule CV-NWT5

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and system control and dispatch service needed to support the transmission service. Formula Rate: The formula rate for CVP NITS includes three components: Component 1: The NITS...

  2. Rate Schedule PACI-T3

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and system control and dispatch service needed to support the transmission service. Formula Rate: The formula rate for PACI firm and non-firm transmission includes three...

  3. Rate Schedule CV-RFS4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    load and for maintaining scheduled interconnection frequency at 60-cycles per second. Formula Rate: The formula rate for regulation includes three components: Component 1: Annual...

  4. Rate Schedule CV-EID4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    that is established in the service agreement or Interconnected Operations Agreements. Formula Rate: The formula rate for EI service includes three components: Component 1: EI...

  5. Power Rates Study Final Proposal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeedingProgram Guidelines This document w w w.pv - te ch.orgPower PlantRates >5

  6. Rate Schedules | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative FuelsofProgram: Report Appendices |ProjectKnow Your PowerWeatherize »Rain orRate

  7. What Is the Right Rate? Loan Rates and Demand | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    What Is the Right Rate? Loan Rates and Demand What Is the Right Rate? Loan Rates and Demand Better Buildings Neighborhood Program Financing Peer Exchange Call: "What is the Right...

  8. Combined Retrieval, Microphysical Retrievals and Heating Rates

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Feng, Zhe

    2013-02-22

    Microphysical retrievals and heating rates from the AMIE/Gan deployment using the PNNL Combined Retrieval.

  9. Combined Retrieval, Microphysical Retrievals and Heating Rates

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Feng, Zhe

    Microphysical retrievals and heating rates from the AMIE/Gan deployment using the PNNL Combined Retrieval.

  10. Property:OpenEI/UtilityRate/DemandRateStructure/Tier4Rate | Open Energy

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo,AltFuelVehicle2 JumpPublicationDate Jump to:InformationEnergyInformation Rate Jump

  11. Materials Safety Liquid Nitrogen Safety! ! A Message from Rick Kelly

    E-Print Network [OSTI]

    (special cryo- gen gloves or leather) and safety glasses with side shields. When dispensing liquid nitrogen from a pressurized dewar, or at any time that a splash may occur, a face shield should also be used as possible. Dispensing from Bulk Stor! age Tanks: Anyone who will be handling liquid nitrogen must complete

  12. 05-20-2010_Final_Testimony_Henry_Kelly.pdf

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    16% of global wind manufacturing capacity (5.4 gigawatts (GW) 5 in the U.S. out of 33 GW worldwide), 6% of global solar manufacturing capacity (0.5 GW out of 9 GW worldwide), and...

  13. TS 14 SIM and Quality Ibrahim Habli and Tim Kelly

    E-Print Network [OSTI]

    Kelly, Tim

    words: GIS, Software Architecture, Requirements, Quality, Software Design SUMMARY Several surveys have fundamental, stage that addresses the achievement of quality requirements for software-intensive systems, like most software-intensive systems, requires a framework that ensures that quality requirements

  14. Evidence of Purifying Selection in Mentor: Angela Yen (Kellis Lab)

    E-Print Network [OSTI]

    Poonen, Bjorn

    Background Genomes Expression Regulation Selection Goal Methods Progress Future Work #12;Human Genome Genome Set of genetic information Grouped into chromosomes Chromosomes made of nucleotides The Human Genome Project (2003) Reference Genome Function? Genes (2%) Regulatory (10-50%) Junk (50-90%) #12

  15. 6-15-11_Final_Testimony__Kelly_.pdf

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    risk, breakthrough projects that could create an entirely new generation of ultra-high energy density, low-cost battery technologies for long-range (300 to 500 miles) plug-in...

  16. 6-7-11_Final_Testimony_(Kelly).pdf

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Before the Committee on Energy and Natural Resources U.S. Senate S. 512, the Nuclear Power 2021 Act and S. 1067, the Nuclear Energy Research Initiative Improvement Act...

  17. Vilas Pol Wins Kelly Award to Attend World Carbon Conference

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to the annual World Carbon Conference. The conference was held in Rio de Janeiro, Brazil, from July 14 to 19, 2013, providing researchers from around the globe with a venue...

  18. Program Contact: Dr. Cian O'Kelly, Program Director

    E-Print Network [OSTI]

    MacMillan, Andrew

    -related apoptosis inducing ligand (TRAIL) mediated apoptosis in human malignant gliomas cells. · Effect of radiation Surgery Residency Program 2D2.02 WMC, 8440 ­ 112 Street Edmonton, AB T6G 2B7 Phone: (780) 407-1591, Fax research endeavors currently include the study of: · Aneurysmal subarachnoid hemorrhage · Dendritic cell

  19. Microsoft Word - FINAL KELLY TESTIMONY clean _4_.docx

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2010, the amount of ethanol that could be blended in gasoline for use in standard vehicle engines without modification was limited to 10 percent ethanol by volume 1 http:...

  20. Kelly Hot Springs Aquaculture Low Temperature Geothermal Facility | Open

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History View NewTexas: Energy ResourcesOrder atHills,NewKeith County, Nebraska: EnergyKellnersville,Energy

  1. ANSER Center member Kelly Lefler successfully defends her dissertation |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefieldSulfateSciTechtail.TheoryTuesday, August 10, 20102016 NewsUsers' Executive09 I N D U S T R I A L S A

  2. Kelly Hot Springs Geothermal Area | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsource History View NewGuam:onItronKanosh Town CorporationsourceEconomies

  3. Federal Energy and Water Management Award Winner Kelly Jaramillo |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:FinancingPetroleum12, 2015Executive Order14, 20111,FYDepartment of5!National

  4. Variable-Rate State Gasoline Taxes

    E-Print Network [OSTI]

    Ang-Olson, Jeffrey; Wachs, Martin; Taylor, Brian D.

    2000-01-01

    J Bradshaw, "SLate ’F~es’ Gasoline Tax So ~t Wdl Rise," TheVarlable-Rate State Gasoline Taxers Jeffrey Ang-Olson MartinVariable-Rate State Gasoline Taxes Jeffrey Ang-Olson

  5. Rate Schedule CV-TPT7

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    or receipt, adjusted for losses, and delivered to points as agreed to by the parties. Formula Rate: The formula rate for transmission of Western's power by others includes three...

  6. Fluorescence Assay for Polymerase Arrival Rates

    E-Print Network [OSTI]

    Che, Austin

    2003-08-31

    To engineer complex synthetic biological systems will require modular design, assembly, and characterization strategies. The RNA polymerase arrival rate (PAR) is defined to be the rate that RNA polymerases arrive at a ...

  7. Fluorescence assay for polymerase arrival rates

    E-Print Network [OSTI]

    Che, Austin, 1979-

    2004-01-01

    To engineer complex synthetic biological systems will require modular design, assembly, and characterization strategies. The RNA polymerase arrival rate (PAR) is defined to be the rate that RNA polymerases arrive at a ...

  8. Energy Efficiency Interest Rate Reduction Program

    Broader source: Energy.gov [DOE]

    For new and existing home purchases that are rated 6 Star or 5 Star Plus, applicants are eligible for an interest rate reduction for the first $200,000 of the loan amount, with a blended interest...

  9. Rate Setting for Small Water Systems 

    E-Print Network [OSTI]

    Dozier, Monty; Theodori, Gene L.; Jensen, Ricard

    2007-03-28

    Knowing how to set the proper rate for water service is a challenge for small water systems. They must generate enough revenue to remain solvent, but offer affordable service. This publication describes the various types of rates and explains...

  10. Home Energy Ratings and Building Performance 

    E-Print Network [OSTI]

    Gardner, J.C.

    2008-01-01

    climate as they affect the rating score of a proposed or completed structure. The rating is used to determine the most cost effective mechanical systems, building envelope design including window and door types, effect of various roofing materials...

  11. Spontaneous Emission Rate Enhancement Using Optical Antennas

    E-Print Network [OSTI]

    Kumar, Nikhil

    2013-01-01

    of  Spontaneous  Emission  in  a  Semiconductor  nanoLED,”  emission  rate  enhancement  using  the  Fluorescent  Emission  by  Lattice   Resonances  in  

  12. Kiwifruitsize influences softening rate during storage

    E-Print Network [OSTI]

    Crisosto, Carlos H.

    Kiwifruitsize influences softening rate during storage Carlos H. Crisosto o David Garner D Katia)at 32*F for 16 weeks. Un- der both storage conditions,large fruit had a slower rate of softening than fruit size and the rate of softening under air and CA conditions will help cold storage managerssafely

  13. An analysis of international grain freight rates 

    E-Print Network [OSTI]

    Jonnala, Sneha Latha

    1999-01-01

    decreasing rate as shipment quantity increases. Highest rates were associated with the berth term followed by the free discharge and free-in-and-out terms. The ships with U.S. flags were found to charge higher rates when compared to ships with foreign flags...

  14. The evolution of the cosmic SN rate

    E-Print Network [OSTI]

    Enrico Cappellaro; Maria Teresa Botticella; Laura Greggio

    2007-06-09

    We briefly review the contribution of SN rate measurements to the debate on SN progenitor scenarios. We find that core collapse rates confirms the rapid evolution of the star formation rate with redshift. After accounting for the dispersion of SN Ia measurements and uncertainty of the star formation history, the standard scenarios for SN Ia progenitors appear consistent with all observational constraints.

  15. CM-1-H Wholesale Power Rate Schedule

    Broader source: Energy.gov [DOE]

    Availability:This rate schedule shall be available to the South Mississippi Electric Power Association, Municipal Energy Agency of Mississippi, and Mississippi Delta Energy Agency (hereinafter...

  16. Rating the energy performance of buildings

    E-Print Network [OSTI]

    Olofsson, Thomas; Meier, Alan; Lamberts, Roberto

    2004-01-01

    T. , (1998), Building Energy Measurement and PerformanceRating a building’s energy performance is becoming anrating of energy performance of buildings. Modern existing

  17. BPA proposes rate increase to bolster

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the proposed wholesale power rate increase is reduced revenue expectations from surplus power sales. Market prices have been, and are forecast to continue to be, suppressed...

  18. Confronting the Graduation Rate Crisis in Texas

    E-Print Network [OSTI]

    Losen, Daniel; Orfield, Gary; Balfanz, Robert

    2006-01-01

    of minority students in Texas attend these schools, comparedfourths of the high schools in Texas where graduation is notthe Graduation Rate Crisis in Texas By Daniel Losen, Gary

  19. Photovoltaic Degradation Rates -- An Analytical Review

    SciTech Connect (OSTI)

    Jordan, D. C.; Kurtz, S. R.

    2012-06-01

    As photovoltaic penetration of the power grid increases, accurate predictions of return on investment require accurate prediction of decreased power output over time. Degradation rates must be known in order to predict power delivery. This article reviews degradation rates of flat-plate terrestrial modules and systems reported in published literature from field testing throughout the last 40 years. Nearly 2000 degradation rates, measured on individual modules or entire systems, have been assembled from the literature, showing a median value of 0.5%/year. The review consists of three parts: a brief historical outline, an analytical summary of degradation rates, and a detailed bibliography partitioned by technology.

  20. Method of controlling fusion reaction rates

    DOE Patents [OSTI]

    Kulsrud, R.M.; Furth, H.P.; Valeo, E.J.; Goldhaber, M.

    1983-05-09

    This invention relates to a method of controlling the reaction rates in a nuclear fusion reactor; and more particularly, to the use of polarized nuclear fuel.

  1. Optimal Rate Allocation in Overlay Content Distribution

    E-Print Network [OSTI]

    Li, Baochun

    Optimal Rate Allocation in Overlay Content Distribution Chuan Wu and Baochun Li Department. This paper addresses the optimal rate allocation problem in overlay content distribution for efficient, these scenarios reflect the contrast between elastic and streaming content distribution, with either per

  2. China's High Savings Rates Rick Harbaugh

    E-Print Network [OSTI]

    Martins, Emília

    the highest in the world. That savings would grow in a country emerging from poverty is not necessarilyChina's High Savings Rates Rick Harbaugh Prepared for conference on "The Rise of China Revisited Abstract Since the early 1980s China has witnessed a rapid increase in its national savings rate to one

  3. Heat release rate markers for premixed combustion

    E-Print Network [OSTI]

    Nikolaou, Zacharias M.; Swaminathan, Nedunchezhian

    2014-06-16

    The validity of the commonly used flame marker for heat release rate (HRR) visualization, namely the rate of the reaction OH + CH2O ? HCO + H2O is re-examined. This is done both for methane–air and multi-component fuel–air mixtures for lean...

  4. Variable word rate N-grams 

    E-Print Network [OSTI]

    Gotoh, Yoshihiko; Renals, Steve

    The rate of occurrence of words is not uniform but varies from document to document. Despite this observation, parameters for conventional N-gram language models are usually derived using the assumption of a constant word rate. In this paper we...

  5. Method of controlling fusion reaction rates

    DOE Patents [OSTI]

    Kulsrud, Russell M. (Princeton, NJ); Furth, Harold P. (Princeton, NJ); Valeo, Ernest J. (Princeton Junction, NJ); Goldhaber, Maurice (Bayport, NY)

    1988-01-01

    A method of controlling the reaction rates of the fuel atoms in a fusion reactor comprises the step of polarizing the nuclei of the fuel atoms in a particular direction relative to the plasma confining magnetic field. Fusion reaction rates can be increased or decreased, and the direction of emission of the reaction products can be controlled, depending on the choice of polarization direction.

  6. Resonances and the thermonuclear reaction rate

    E-Print Network [OSTI]

    M. S. Hussein; M. Ueda; A. J. Sargeant; M. P. Pato

    2003-07-21

    We present an approximate analytic expression for thermonuclear reaction rate of charged particles when the cross section contains a single narrow or wide resonance described by a Breit-Wigner shape. The resulting expression is uniformly valid as the effective energy and resonance energy coalesce. We use our expressions to calculate the reaction rate for $^{12}$C(p,$\\gamma$)$^{13}$N.

  7. Polycyclic Aromatic Hydrocarbon Biodegradation Rates: A

    E-Print Network [OSTI]

    Peters, Catherine A.

    Polycyclic Aromatic Hydrocarbon Biodegradation Rates: A Structure-Based Study K R I S T I N E H . W structure in determining the biodegradation rates of polycyclic aromatic hydrocarbons (PAHs). Laboratory. Introduction Polycyclic aromatic hydrocarbons (PAHs) are a class of organic pollutants that are commonly found

  8. Cadmium Biosorption Rate in Protonated Sargassum Biomass

    E-Print Network [OSTI]

    Volesky, Bohumil

    Cadmium Biosorption Rate in Protonated Sargassum Biomass J I N B A I Y A N G A N D B O H U M I L V Sargassum fluitans biomass was accompanied by the release of hydrogen protons from the biomass. The uptake the overall biosorption rate of cadmium ions in flat seaweed biomass particles. The overall biosorption

  9. Measuring Degradation Rates Without Irradiance Data

    SciTech Connect (OSTI)

    Pulver, S.; Cormode, D.; Cronin, A.; Jordan, D.; Kurtz, S.; Smith, R.

    2011-02-01

    A method to report PV system degradation rates without using irradiance data is demonstrated. First, a set of relative degradation rates are determined by comparing daily AC final yields from a group of PV systems relative to the average final yield of all the PV systems. Then, the difference between relative and absolute degradation rates is found from a statistical analysis. This approach is verified by comparing to methods that utilize irradiance data. This approach is significant because PV systems are often deployed without irradiance sensors, so the analysis method described here may enable measurements of degradation using data that were previously thought to be unsuitable for degradation studies.

  10. Considerations for How to Rate CPV

    SciTech Connect (OSTI)

    Kurtz, S.; Miller, M.; Marion, B.; Emery, K.; McConnell, R.; Surendran, S.; Kimber, A.

    2011-02-01

    The concentrator photovoltaic (CPV) industry is introducing multiple products into the marketplace, but, as yet, the; community has not embraced a unified method for assessing a nameplate rating. The choices of whether to use 850,; 900, or 1000 W/m2 for the direct-normal irradiance and whether to link the rating to ambient or cell temperature will; affect how CPV modules are rated and compared with other technologies. This paper explores the qualitative and; quantitative ramifications of these choices using data from two multi-junction CPV modules and two flat-plate; modules.

  11. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtility RateUtility Rate

  12. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtilityRateUtility Rate

  13. Cooling rate, heating rate, and aging effects in glassy water Nicolas Giovambattista,1

    E-Print Network [OSTI]

    Sciortino, Francesco

    Cooling rate, heating rate, and aging effects in glassy water Nicolas Giovambattista,1 H. Eugene of water molecules during the process of generating a glass by cooling, and during the process on the cooling/heating rates as well as on the role of aging (the time elapsed in the glass state). We compare

  14. Does Growth Rate Determine the Rate of Metabolism in Shorebird Chicks Living in the Arctic?

    E-Print Network [OSTI]

    Williams, Jos. B.

    primarily of greater metabolic inten- sities of heat-generating tissues. The maximum temperature gradient500 Does Growth Rate Determine the Rate of Metabolism in Shorebird Chicks Living in the Arctic/22/2007; Electronically Published 7/13/2007 ABSTRACT We measured resting and peak metabolic rates (RMR and PMR

  15. Dependence of Up-scaled Reaction Rate on Flow Rate in Porous Media

    E-Print Network [OSTI]

    New York at Stoney Brook, State University of

    to inherent heterogeneities in structure, mineral placement and fluid velocity in rock, bulk reaction rates1 Dependence of Up-scaled Reaction Rate on Flow Rate in Porous Media D. Kim · W. B. Lindquist model simulations of anorthite and kaolinite reactions in two sandstone pore networks under acidic

  16. Contractor Rating and Feedback Systems | Department of Energy

    Energy Savers [EERE]

    Rating and Feedback Systems Contractor Rating and Feedback Systems Better Buildings Residential Workforce Business Partners Peer Exchange Call Series: Contractor Rating and...

  17. Tier 2 Vintage Rate Workshop II

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rates. These are intended to be based on specific resource costs for customers that need power to be based on specific resource types (e.g., renewable) or that want to know more...

  18. Rate Schedule CV-F13

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for the entire FY. The PRR is allocated to FP Customers and BR Customers based on formula rates, as adjusted for Hourly Exchange (HE), FP true-up calculation, and midyear...

  19. Regularization of Tunneling Rates with Quantum Chaos

    E-Print Network [OSTI]

    Pecora, Louis M; Wu, Dong-Ho

    2012-01-01

    We study tunneling in various shaped, closed, two-dimensional, flat potential, double wells by calculating the energy splitting between symmetric and anti-symmetric state pairs. For shapes that have regular or nearly regular classical behavior (e.g. rectangular or circular) the tunneling rates vary greatly over wide ranges often by several orders of magnitude. However, for well shapes that admit more classically chaotic behavior (e.g. the stadium, the Sinai billiard) the range of tunneling rates narrows, often by orders of magnitude. This dramatic narrowing appears to come from destabilization of periodic orbits in the regular wells that produce the largest and smallest tunneling rates and causes the splitting vs. energy relation to take on a possibly universal shape. It is in this sense that we say the quantum chaos regularizes the tunneling rates.

  20. Essays on exchange rates and electricity demand

    E-Print Network [OSTI]

    Li, Xiangming, 1966-

    1999-01-01

    This thesis examines two important issues in economic development: exchange rates and electricity demand and addresses methodological issues of using time series and panel data analysis to investigate important policy ...

  1. Uncertainty Analysis for Photovoltaic Degradation Rates (Poster)

    SciTech Connect (OSTI)

    Jordan, D.; Kurtz, S.; Hansen, C.

    2014-04-01

    Dependable and predictable energy production is the key to the long-term success of the PV industry. PV systems show over the lifetime of their exposure a gradual decline that depends on many different factors such as module technology, module type, mounting configuration, climate etc. When degradation rates are determined from continuous data the statistical uncertainty is easily calculated from the regression coefficients. However, total uncertainty that includes measurement uncertainty and instrumentation drift is far more difficult to determine. A Monte Carlo simulation approach was chosen to investigate a comprehensive uncertainty analysis. The most important effect for degradation rates is to avoid instrumentation that changes over time in the field. For instance, a drifting irradiance sensor, which can be achieved through regular calibration, can lead to a substantially erroneous degradation rates. However, the accuracy of the irradiance sensor has negligible impact on degradation rate uncertainty emphasizing that precision (relative accuracy) is more important than absolute accuracy.

  2. Dynamic Line Rating: Research and Policy Evaluation

    SciTech Connect (OSTI)

    Jake P. Gentle; Kurt S. Myers; Michael R. West

    2014-07-01

    Dynamic Line Rating (DLR) is a smart grid technology that allows the rating of electrical conductors to be increased based on local weather conditions. Overhead lines are conventionally given a conservative rating based on worst case scenarios. We demonstrate that observing the conditions in real time leads to additional capacity and safer operation. This paper provides a report of a pioneering scheme in the United States of America in which DLR has been applied. Thereby, we demonstrate that observing the local weather conditions in real time leads to additional capacity and safer operation. Secondly, we discuss limitations involved. In doing so, we arrive at novel insights which will inform and improve future DLR projects. Third, we provide a policy background and discussion to clarify the technology’s potential and identifies barriers to the imminent adoption of dynamic line rating systems. We provide suggestions for regulatory bodies about possible improvements in policy to encourage adoption of this beneficial technology.

  3. Extratropical Lapse Rates in Very Hot Climates 

    E-Print Network [OSTI]

    Zamora, Ryan Alexander

    2013-07-02

    circulation in progressively warmer climate states. As a tool to assess the stability of the atmosphere, we calculate a thermodynamic variable called saturation potential vorticity (P*), which has the property of being identically zero wherever lapse rates...

  4. Negotiating Rates and Contracts for Qualifying Facilities 

    E-Print Network [OSTI]

    Collier, S. E.

    1986-01-01

    . This paper describes the key issues involved in the development of purchase rates, as well as supplemental power services, and contract terms and conditions. Attention is given to special issues such as wheeling, losses, and regulatory proceedings. A general...

  5. PSNC Energy (Gas)- Green Building Rate Discount

    Office of Energy Efficiency and Renewable Energy (EERE)

    This discounted rate is available to commercial customers whose building meets the U.S. Green Building Council’s Leadership in Energy and Environmental Design (LEED) certification or equivalent. To...

  6. Extended range radiation dose-rate monitor

    DOE Patents [OSTI]

    Valentine, Kenneth H. (Knoxville, TN)

    1988-01-01

    An extended range dose-rate monitor is provided which utilizes the pulse pileup phenomenon that occurs in conventional counting systems to alter the dynamic response of the system to extend the dose-rate counting range. The current pulses from a solid-state detector generated by radiation events are amplified and shaped prior to applying the pulses to the input of a comparator. The comparator generates one logic pulse for each input pulse which exceeds the comparator reference threshold. These pulses are integrated and applied to a meter calibrated to indicate the measured dose-rate in response to the integrator output. A portion of the output signal from the integrator is fed back to vary the comparator reference threshold in proportion to the output count rate to extend the sensitive dynamic detection range by delaying the asymptotic approach of the integrator output toward full scale as measured by the meter.

  7. Calibration and Rating of Photovoltaics: Preprint

    SciTech Connect (OSTI)

    Emery, K.

    2012-06-01

    Rating the performance of photovoltaic (PV) modules is critical to determining the cost per watt, and efficiency is useful to assess the relative progress among PV concepts. Procedures for determining the efficiency for PV technologies from 1-sun to low concentration to high concentration are discussed. We also discuss the state of the art in primary and secondary calibration of PV reference cells used by calibration laboratories around the world. Finally, we consider challenges to rating PV technologies and areas for improvement.

  8. Intraclass Price Elasticity & Electric Rate Design 

    E-Print Network [OSTI]

    Gresham, K. E.

    1987-01-01

    beyond this becomes more elastic as usage increases. In the book "Innovative Electric, Rates," John Chamberlin and Charles Dickson utilize an economic model to test conservation programs. This model utilizes intrac1ass price elasticities and has a.... Utilities must rely on customer data and intuition to estimate customer response to rate changes. These methods have several downfalls. First, the customer data may not reflect customer behavior in an economic downturn. Second, the data may not exactly...

  9. Solar Models and NACRE thermonuclear reaction rates

    E-Print Network [OSTI]

    P. Morel; B. Pichon; J. Provost; G. Berthomieu

    1999-07-27

    Using the most recent updated physics, calibrated solar models have been computed with the new thermonuclear reaction rates of NACRE, the recently available European compilation. Comparisons with models computed with the reaction rates of Caughlan & Fowler (\\cite{cf88}) and of Adelberger et al. (\\cite{a98}) are made for global structure, expected neutrinos fluxes, chemical composition and sound speed profiles, helioseismological properties of p-modes and g-modes.

  10. Rating of Mixed Split Residential Air Conditioners 

    E-Print Network [OSTI]

    Domanski, P. A.

    1988-01-01

    require that manufac- turers derive cooling ratings for unitary systems by testing a sample of sufficient size to meet certain specified statistical confidence levels. For split unitary systems comprising an outdoor unit and an indoor coil assembly...(95), SEER, and recommended indoor volumetric flow rate of air, are publicly available. The procedure also assumee that the matched indoor section is available for inspection and evaluation of the indoor coil capacity and the indoor fan power...

  11. Radiation Leukemogenesis at Low Dose Rates

    SciTech Connect (OSTI)

    Weil, Michael; Ullrich, Robert

    2013-09-25

    The major goals of this program were to study the efficacy of low dose rate radiation exposures for the induction of acute myeloid leukemia (AML) and to characterize the leukemias that are caused by radiation exposures at low dose rate. An irradiator facility was designed and constructed that allows large numbers of mice to be irradiated at low dose rates for protracted periods (up to their life span). To the best of our knowledge this facility is unique in the US and it was subsequently used to study radioprotectors being developed for radiological defense (PLoS One. 7(3), e33044, 2012) and is currently being used to study the role of genetic background in susceptibility to radiation-induced lung cancer. One result of the irradiation was expected; low dose rate exposures are ineffective in inducing AML. However, another result was completely unexpected; the irradiated mice had a very high incidence of hepatocellular carcinoma (HCC), approximately 50%. It was unexpected because acute exposures are ineffective in increasing HCC incidence above background. This is a potential important finding for setting exposure limits because it supports the concept of an 'inverse dose rate effect' for some tumor types. That is, for the development of some tumor types low dose rate exposures carry greater risks than acute exposures.

  12. Utility Rate Structures and the Impact of Energy Efficiency and...

    Energy Savers [EERE]

    FL Energy Efficiency Calculations * Rates: most common are energy only rates, or a demand rate (kVa or kW) * Demand Rate - Can't use the average cost per kWh for calculations -...

  13. FITCH RATES ENERGY NORTHWEST, WA'S ELECTRIC REV RFDG BONDS 'AA...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FITCH RATES ENERGY NORTHWEST, WA'S ELECTRIC REV RFDG BONDS 'AA'; OUTLOOK STABLE Fitch Ratings-Austin-22 September 2015: Fitch Ratings assigns its 'AA' rating to the following bonds...

  14. Analytical Improvements in PV Degradation Rate Determination

    SciTech Connect (OSTI)

    Jordan, D. C.; Kurtz, S. R.

    2011-02-01

    As photovoltaic (PV) penetration of the power grid increases, it becomes vital to know how decreased power output may affect cost over time. In order to predict power delivery, the decline or degradation rates must be determined accurately. For non-spectrally corrected data several complete seasonal cycles (typically 3-5 years) are required to obtain reasonably accurate degradation rates. In a rapidly evolving industry such a time span is often unacceptable and the need exists to determine degradation rates accurately in a shorter period of time. Occurrence of outliers and data shifts are two examples of analytical problems leading to greater uncertainty and therefore to longer observation times. In this paper we compare three methodologies of data analysis for robustness in the presence of outliers, data shifts and shorter measurement time periods.

  15. Nuclear weak interaction rates in primordial nucleosynthesis

    E-Print Network [OSTI]

    George M. Fuller; Christel J. Smith

    2010-09-01

    We calculate the weak interaction rates of selected light nuclei during the epoch of Big Bang Nucleosynthesis (BBN), and we assess the impact of these rates on nuclear abundance flow histories and on final light element abundance yields. We consider electron and electron antineutrino captures on 3He and 7Be, and the reverse processes of positron capture and electron neutrino capture on 3H and 7Li. We also compute the rates of positron and electron neutrino capture on 6He. We calculate beta and positron decay transitions where appropriate. As expected, the final standard BBN abundance yields are little affected by addition of these weak processes, though there can be slight alterations of nuclear flow histories. However, non-standard BBN scenarios, e.g., those involving out of equilibrium particle decay with energetic final state neutrinos, may be affected by these processes.

  16. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Home > Utility Rate

  17. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Home >Utility Rate

  18. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtility Rate Home >

  19. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtility Rate Home

  20. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtility Rate HomeUtility

  1. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtility Rate

  2. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtility RateUtility

  3. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtilityRate Home >

  4. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtilityRate Home

  5. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtilityRate HomeUtility

  6. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtilityRate

  7. Financial Choices Home Page (pbl/rates)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would likeUniverse (Journal Article) |Final Report DocumentRates > Rates Announcements

  8. The heritability of daily ranges in rectal temperature, respiration rate, and pulse rate in lactating cows 

    E-Print Network [OSTI]

    Vega C., Eduardo Humberto

    1957-01-01

    GMV 'KLl% NOIXVEIdSZH ZHflLVKEcBCiU 'IVLVK ar SZONVK ZrZVa n urrISVZIXe SSX THE HERITABILITY QF DAILT RANGES IR RECTAL TRAPE3ATCRE y HE V IRATI CR RATE & AHD PULSE RATE IR LACTATIlgl CCHH A Thesis Muardo Susbarto Vega C Appreved as to style... for the Daily Ranges of Tem- perature, Pulse Rate? snd Respiration Rate of Holsteins and Jerseys Prior to Adjustmsnt . ~ ~ ~ 13 IXX, Beans? Standard Errors, and Nunber of Observations for the Three Chax'aeter istics Beasuxed, After Adjustment ~ ~ ~ ~ ~ 13...

  9. Equity Options and Stochastic Interest Rates1

    E-Print Network [OSTI]

    Ouwehand, Peter

    M Acott February 14, 2006 1 The financial assistance of the Department of Labour (DoL) towards risk of equity options except around the Optimal Exercise Boundary of American options, but displays enhanced convexity (i.e. `Gamma'-type risks) over the stochastic interest rate model. #12;Acknowledgements

  10. Interruptible Electric Rates: Where We Are Today 

    E-Print Network [OSTI]

    Frees, R. J.

    1982-01-01

    of energy management. Within the past few years, time-of-use rates, for both industrial and residential users, have been touted as the answer to shaving peaks and filling valleys in a utility's load curve. Their effectiveness in doing so, however, is still...

  11. Electric germs Source: scenta Rate this item

    E-Print Network [OSTI]

    Lovley, Derek

    Electric germs Source: scenta Rate this item People in remote areas could benefit from fuel cells that contain bacteria that grows prolifically on the graphite anodes of fuel cells and can conduct electricity surface that conducted electricity. Presenting his findings at the Society for General Microbiology

  12. The distant type Ia supernova rate

    SciTech Connect (OSTI)

    Pain, R.; Fabbro, S.; Sullivan, M.; Ellis, R.S.; Aldering, G.; Astier, P.; Deustua, S.E.; Fruchter, A.S.; Goldhaber, G.; Goobar, A.; Groom, D.E.; Hardin, D.; Hook, I.M.; Howell, D.A.; Irwin, M.J.; Kim, A.G.; Kim, M.Y.; Knop, R.A.; Lee, J.C.; Perlmutter, S.; Ruiz-Lapuente, P.; Schahmaneche, K.; Schaefer, B.; Walton, N.A.

    2002-05-20

    We present a measurement of the rate of distant Type Ia supernovae derived using 4 large subsets of data from the Supernova Cosmology Project. Within this fiducial sample,which surveyed about 12 square degrees, thirty-eight supernovae were detected at redshifts 0.25--0.85. In a spatially flat cosmological model consistent with the results obtained by the Supernova Cosmology Project, we derive a rest-frame Type Ia supernova rate at a mean red shift z {approx_equal} 0.55 of 1.53 {sub -0.25}{sub -0.31}{sup 0.28}{sup 0.32} x 10{sup -4} h{sup 3} Mpc{sup -3} yr{sup -1} or 0.58{sub -0.09}{sub -0.09}{sup +0.10}{sup +0.10} h{sup 2} SNu(1 SNu = 1 supernova per century per 10{sup 10} L{sub B}sun), where the first uncertainty is statistical and the second includes systematic effects. The dependence of the rate on the assumed cosmological parameters is studied and the redshift dependence of the rate per unit comoving volume is contrasted with local estimates in the context of possible cosmic star formation histories and progenitor models.

  13. REVERSE-ENGINEERING COUNTRY RISK RATINGS: A ...

    E-Print Network [OSTI]

    2008-11-10

    Feb 19, 1999 ... This study provides new insights on the importance of variables by supporting the necessity of ..... system is that of (iii) self-containment, i.e. its non-reliance on any other past or present country risk ratings. ...... 1131-1151.

  14. Instrumented Home Energy Rating and Commissioning

    E-Print Network [OSTI]

    Secretary for Energy Efficiency and Renewable Energy, Building Technologies Program, of the U.S. DepartmentLBNL-52216 Instrumented Home Energy Rating and Commissioning Craig Wray, Iain Walker, Max Sherman Environmental Energy Technologies Division Indoor Environment Department Lawrence Berkeley National Laboratory

  15. Overview of Field Experience - Degradation Rates & Lifetimes

    SciTech Connect (OSTI)

    Jordan, Dirk; Kurtz, Sarah

    2015-09-14

    The way a PV module fails may depend not only on its design and the materials used in its construction, but also on the weather it experiences, the way it is mounted, and the quality control during its manufacture. This presentation gives an overview of Field Experience - what degradation rates and what lifetimes are being observed in various regions.

  16. Eucalyptus fuelwood growth rate improves with age

    E-Print Network [OSTI]

    Eucalyptus fuelwood growth rate improves with age Dean R. Donaldson 0 Richard B. Standiford I n The two species of Eucalyptus were the fastest growing of the five tree spe- cies evaluated at Grant Street (table 1). Manna gum, Eucalyptus viminalis, al- though about a year younger, is signifi- cantly

  17. Dual Baud Rate Generator Programmable Divider

    E-Print Network [OSTI]

    Mann, Tim

    to excessive loading. The output of the oscillatorlbuffer is applied to the dividers for generation, inclusive. If the divisor is even, the output will be square: otherwise the output will be high longer thanAPPENDIX B #12;#12;Dual Baud Rate Generator Programmable Divider FEATURES PIN CONFi

  18. Prediction of Thermonuclear Reaction Rates in Astrophysics

    E-Print Network [OSTI]

    T. Rauscher

    1998-10-15

    Recent improvements and remaining problems in the prediction of thermonuclear rates are reviewed. The main emphasis is on statistical model calculations, but the challenge to include direct reactions close to the driplines is also briefly addressed. Further theoretical as well as experimental investigations are motivated.

  19. A New Series of Rate Decline Relations Based on the Diagnosis of Rate-Time Data 

    E-Print Network [OSTI]

    Boulis, Anastasios

    2010-01-14

    point for their derivation is given by the definitions of the "loss ratio" and the "derivative of the loss ratio", where the "loss ratio" is the ratio of rate data to derivative of rate data, and the "derivative of the loss ratio" is the "b...

  20. Thermal dilepton rates from quenched lattice QCD

    E-Print Network [OSTI]

    H. -T. Ding; A. Francis; O. Kaczmarek; F. Karsch; E. Laermann; S. Mukherjee; M. Müller; W. Soeldner

    2013-01-30

    We present new lattice results on the continuum extrapolation of the vector current correlation function. Lattice calculations have been carried out in the deconfined phase at a temperature of 1.1 Tc, extending our previous results at 1.45 Tc, utilizing quenched non-perturbatively clover-improved Wilson fermions and light quark masses. A systematic analysis on multiple lattice spacings allows to perform the continuum limit of the correlation function and to extract spectral properties in the continuum limit. Our current analysis suggests the results for the electrical conductivity are proportional to the temperature and the thermal dilepton rates in the quark gluon plasma are comparable for both temperatures. Preliminary results of the continuum extrapolated correlation function at finite momenta, which relates to thermal photon rates, are also presented.

  1. Feed rate measuring method and system

    DOE Patents [OSTI]

    Novak, J.L.; Wiczer, J.J.

    1995-12-05

    A system and method are provided for establishing the feed rate of a workpiece along a feed path with respect to a machine device. First and second sensors each having first and second sensing electrodes which are electrically isolated from the workpiece are positioned above, and in proximity to the desired surfaces of the workpiece along a feed path. An electric field is developed between the first and second sensing electrodes of each sensor and capacitance signals are developed which are indicative of the contour of the workpiece. First and second image signals representative of the contour of the workpiece along the feed path are developed by an image processor. The time delay between corresponding portions of the first and second image signals are then used to determine the feed rate based upon the separation of the first and second sensors and the amount of time between corresponding portions of the first and second image signals. 18 figs.

  2. EDC-37 Deflagration Rates at Elevated Pressures

    SciTech Connect (OSTI)

    Maienschein, J L; Koerner, J G

    2008-01-31

    We report deflagration rates on EDC-37 at high pressures. Experiments are conducted using the Lawrence Livermore National Laboratory High Pressure Strand Burner (HPSB) apparatus. The HPSB contains a deflagrating sample in a small volume, high pressure chamber. The sample consists of nine, 6.35 mm diameter, 6.35 mm length cylinders stacked on end, with burn wires placed between cylinders. Sample deflagration is limited to the cross-sectional surface of the cylinder by coating the cylindrical surface of the tower with Halthane 88-2 epoxy. Sample deflagration is initiated on one end of the tower by a B/KNO{sub 3} and HNS igniter train. Simultaneous temporal pressure history and burn front time of arrival measurements yield the laminar deflagration rate for a range of pressures and provide insight into deflagration uniformity. These measurements are one indicator of overall thermal explosion violence. Specific details of the experiment and the apparatus can be found in the literature.

  3. Predict carbonation rate on iron catalyst

    SciTech Connect (OSTI)

    Dry, M.E.

    1980-02-01

    On solely thermodynamic grounds, the main hydrocarbon product of the Fischer-Tropsch reaction should be methane; in practice, however, carbon is frequently produced as well and deposited on the iron catalyst, fouling the active surface sites. South African Coal, Oil and Gas Corp., Ltd.'s experiments with a fluidized Fischer-Tropsch catalyst bed demonstrate that the rate of carbon deposition is strongly dependent on the hydrogen partial pressure in the reactor, much less dependent on the CO pressure, and not affected at all by the pressure of CO/sub 2/. A suggested reaction scheme for the Fischer-Tropsch synthesis explains these observations and provides a basis for a correlation useful in predicting carbon-deposition rates.

  4. Consumers face $5. 9 million rate increase

    SciTech Connect (OSTI)

    Not Available

    1984-11-01

    Testimony at hearings before the Garrison Diversion Compromise Commission claimed that rural consumers in the Upper Midwest could face $5.9 million in electric rate increases if the commission deauthorizes the project and hydroelectric rates go up to pay the costs of the 1944 Pick-Sloan project originally assigned to irrigation. If there is no irrigation development, the revenue that irrigation must raise to repay the $67 million debt assigned to irrigation must be reassigned to hydroelectric power. The commission represents a compromise between supporters and opponents of the Garrison Diversion project. Spokesmen for regional utilities spoke in support of the project as an investment whose costs have escalated because of delays at the expense of economic development in North Dakota.

  5. Smokeless Control of Flare Steam Flow Rate 

    E-Print Network [OSTI]

    Agar, J.; Balls, B. W.

    1979-01-01

    inside the glass. The instrument has a vibrating spool accu rately machined from a material resistant to wet H2S, The patented flow path through the transducer (Figure 8) inhibits moisture and dirt from contaminating the spool and enables installation..., also the inclusion of average values for ZG and ZA' REFERENCES 1. API Publication 931, Chapter 15, "Flares", Manual on Disposal of Refinery Wastes, Volume on Atmospheric Emissions, 1977 American Petroleum Institute, Refinery Department, 2120 L...

  6. Rate allocation in a remote control structure 

    E-Print Network [OSTI]

    Meadow, Charles Joe

    1984-01-01

    are linearly dependent upon the measurement estimates. Therefore, they can be considered as stationary and gaussian. To optimally encode a signal an arbitrary time delay is required which will produce a non-causal control solution. This is a non.... Jones (Head of Department) May 1984 ABSTRACT Rate Allocation in a Remote Control Structure (May 1984) Charles Joe Meadow, Jr. , B. S. , Texas A&M University Chairman of Advisory Committee: Dr. Thomas R. Fischer A Linear-Quadratic-Gaussian (LQG...

  7. High-Rate Capable Floating Strip Micromegas

    E-Print Network [OSTI]

    Jonathan Bortfeldt; Michael Bender; Otmar Biebel; Helge Danger; Bernhard Flierl; Ralf Hertenberger; Philipp Lösel; Samuel Moll; Katia Parodi; Ilaria Rinaldi; Alexander Ruschke; André Zibell

    2015-08-04

    We report on the optimization of discharge insensitive floating strip Micromegas (MICRO-MEsh GASeous) detectors, fit for use in high-energy muon spectrometers. The suitability of these detectors for particle tracking is shown in high-background environments and at very high particle fluxes up to 60MHz/cm$^2$. Measurement and simulation of the microscopic discharge behavior have demonstrated the excellent discharge tolerance. A floating strip Micromegas with an active area of 48cm$\\times$50cm with 1920 copper anode strips exhibits in 120GeV pion beams a spatial resolution of 50$\\mu$m at detection efficiencies above 95%. Pulse height, spatial resolution and detection efficiency are homogeneous over the detector. Reconstruction of particle track inclination in a single detector plane is discussed, optimum angular resolutions below $5^\\circ$ are observed. Systematic deviations of this $\\mu$TPC-method are fully understood. The reconstruction capabilities for minimum ionizing muons are investigated in a 6.4cm$\\times$6.4cm floating strip Micromegas under intense background irradiation of the whole active area with 20MeV protons at a rate of 550kHz. The spatial resolution for muons is not distorted by space charge effects. A 6.4cm$\\times$6.4cm floating strip Micromegas doublet with low material budget is investigated in highly ionizing proton and carbon ion beams at particle rates between 2MHz and 2GHz. Stable operation up to the highest rates is observed, spatial resolution, detection efficiencies, the multi-hit and high-rate capability are discussed.

  8. Subsurface heaters with low sulfidation rates

    DOE Patents [OSTI]

    John, Randy Carl; Vinegar, Harold J

    2013-12-10

    A system for heating a hydrocarbon containing formation includes a heater having an elongated ferromagnetic metal heater section. The heater is located in an opening in a formation. The heater section is configured to heat the hydrocarbon containing formation. The exposed ferromagnetic metal has a sulfidation rate that goes down with increasing temperature of the heater, when the heater is in a selected temperature range.

  9. Reducing Your Leak Rate Without Repairing Leaks 

    E-Print Network [OSTI]

    Beals, C.

    2005-01-01

    below the header pressure have the added advantage of reducing the air consumption of equipment, as well as reducing the leak rate. Turn Off the Air to Idle Equipment In most plants, when production equipment operators shut off their equipment... of the reason why plant personnel often find leak repair unproductive. The other reason relates to the compressor controls. If the plant had several lubricated rotary screw compressors operating in modulation, repairing 2,000 cfm in leaks may only reduce...

  10. Dynamic Phase Transition, Enhanced Reaction Rate, and

    E-Print Network [OSTI]

    Rikvold, Per Arne

    is a CO, they react [CO + O CO2(g)] These dynamical rules fully define the model. Its properties on a crystal surface by Langmuir-Hinshelwood mechanism: CO(g)+S CO(a) O2 + 2S 2O(a) CO(a) + O(a) CO2(g) + 2S been observed experimentally for high enough temperatures. Add CO desorption rate k to mimic

  11. Wholesale Power Rate Schedules | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative FuelsofProgram: Report1538-1950DepartmentWave EnergyElectricityRate Schedules »

  12. Heating Rate Profiles in Galaxy Clusters

    E-Print Network [OSTI]

    Edward C. D. Pope; Georgi Pavlovski; Christian R. Kaiser; Hans Fangohr

    2006-01-05

    In recent years evidence has accumulated suggesting that the gas in galaxy clusters is heated by non-gravitational processes. Here we calculate the heating rates required to maintain a physically motived mass flow rate, in a sample of seven galaxy clusters. We employ the spectroscopic mass deposition rates as an observational input along with temperature and density data for each cluster. On energetic grounds we find that thermal conduction could provide the necessary heating for A2199, Perseus, A1795 and A478. However, the suppression factor, of the clasical Spitzer value, is a different function of radius for each cluster. Based on the observations of plasma bubbles we also calculate the duty cycles for each AGN, in the absence of thermal conduction, which can provide the required energy input. With the exception of Hydra-A it appears that each of the other AGNs in our sample require duty cycles of roughly $10^{6}-10^{7}$ yrs to provide their steady-state heating requirements. If these duty cycles are unrealistic, this may imply that many galaxy clusters must be heated by very powerful Hydra-A type events interspersed between more frequent smaller-scale outbursts. The suppression factors for the thermal conductivity required for combined heating by AGN and thermal conduction are generally acceptable. However, these suppression factors still require `fine-tuning` of the thermal conductivity as a function of radius. As a consequence of this work we present the AGN duty cycle as a cooling flow diagnostic.

  13. 2007 Wholesale Power Rate Case Initial Proposal : Wholesale Power Rate Development Study.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    2007-11-01

    The Wholesale Power Rate Development Study (WPRDS) calculates BPA proposed rates based on information either developed in the WPRDS or supplied by the other studies that comprise the BPA rate proposal. All of these studies, and accompanying documentation, provide the details of computations and assumptions. In general, information about loads and resources is provided by the Load Resource Study (LRS), WP-07-E-BPA-01, and the LRS Documentation, WP-07-E-BPA-01A. Revenue requirements information, as well as the Planned Net Revenues for Risk (PNNR), is provided in the Revenue Requirement Study, WP-07-E-BPA-02, and its accompanying Revenue Requirement Study Documentation, WP-07-E-BPA-02A and WP-07-E-BPA-02B. The Market Price Forecast Study (MPFS), WP-07-E-BPA-03, and the MPFS Documentation, WP-07-E-BPA-03A, provide the WPRDS with information regarding seasonal and diurnal differentiation of energy rates, as well information regarding monthly market prices for Demand Rates. In addition, this study provides information for the pricing of unbundled power products. The Risk Analysis Study, WP-07-E-BPA-04, and the Risk Analysis Study Documentation, WP-07-E-BPA-04A, provide short-term balancing purchases as well as secondary energy sales and revenue. The Section 7(b)(2) Rate Test Study, WP-07-E-BPA-06, and the Section 7(b)(2) Rate Test Study Documentation, WP-07-E-BPA-06A, implement Section 7(b)(2) of the Northwest Power Act to ensure that BPA preference customers firm power rates applied to their general requirements are no higher than rates calculated using specific assumptions in the Northwest Power Act.

  14. PowerChoice Residential Customer Response to TOU Rates

    E-Print Network [OSTI]

    Peters, Jane S.

    2010-01-01

    1983. Time-of-Day Electricity Rates for the United States.to Voluntary Time-of-Use Electricity Rates. ” Resource andCompared to your old electricity rate, would you say that

  15. Variable rate CELP speech coding using widely variable parameter updates 

    E-Print Network [OSTI]

    Moodie, Myron L.

    1995-01-01

    Code-excited, linear prediction (CELP) has become an accepted method for low bit rate, high quality coding of digital speech. The success of fixed rate CELP schemes has led to increased interest in variable rate techniques ...

  16. The Problem of Second-Hand Industrial Equipment: Reclaiming a Missed Opportunity 

    E-Print Network [OSTI]

    Kelly-Detwiler, P.; Opheim, K.

    1997-01-01

    OF SECOND-HAND INDUSTRIAL EQUIPMENT: RECLAIMING A MISSED OPPORTUNITY Peter Kelly-Detwiler Kelly Opheim Project Manager International Institute Program Manager IIEC-Latin America for Energy Conservation IIEC-North America Santiago, Chile Washington, DC... rapidly, and relatively high rates of risk and uncertainty leading to very high discount rates among equipment purchasers. In addition, the comparatively low costs of inputs including labor, energy and materials mean that even quite energy...

  17. Flow rate--pressure drop relation for deformable shallow microfluidic...

    Office of Scientific and Technical Information (OSTI)

    Conference: Flow rate--pressure drop relation for deformable shallow microfluidic channels Citation Details In-Document Search Title: Flow rate--pressure drop relation for...

  18. Auto/Steel Partnership: AHSS Stamping, Strain Rate Characterization...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AHSS Stamping, Strain Rate Characterization, Sheet Steel Fatigue, AHSS Joining AutoSteel Partnership: AHSS Stamping, Strain Rate Characterization, Sheet Steel Fatigue, AHSS...

  19. Auto/Steel Partnership: Fatigue of AHSS Strain Rate Characterization...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fatigue of AHSS Strain Rate Characterization AutoSteel Partnership: Fatigue of AHSS Strain Rate Characterization 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual...

  20. BPA sets agency rates for fiscal years 2016-2017

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and environmentally sustainable way possible," said BPA Administrator and CEO Elliot Mainzer. "The rates in the Final ROD reflect that collaborative effort." Power rates...

  1. Western-UGP Transmission and Ancillary Services Rates Customer...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (Updated December 16, 2014, with changes noted in the following sections: Proposed Formula Rate for Scheduling, System Control and Dispatch Service, Proposed Rate for...

  2. Controlling the Actuation Rate of Low Density Shape Memory Polymer...

    Office of Scientific and Technical Information (OSTI)

    Controlling the Actuation Rate of Low Density Shape Memory Polymer Foams in Water Citation Details In-Document Search Title: Controlling the Actuation Rate of Low Density Shape...

  3. Control Strategies for Centrifugal Pumps with Variable Flow Rate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Control Strategies for Centrifugal Pumps with Variable Flow Rate Requirements Control Strategies for Centrifugal Pumps with Variable Flow Rate Requirements This tip sheet discusses...

  4. The Inverse Problem for Derivative Securities of Interest Rate

    E-Print Network [OSTI]

    2008-02-02

    May 26, 2000 ... Market price for risk of interest rate reflects the close relation between risk and yield of securities dependent on interest rate. An inverse problem.

  5. California Federal Facilities: Rate-Responsive Buidling Operating...

    Office of Environmental Management (EM)

    Federal Facilities: Rate-Responsive Buidling Operating for Deeper Cost and Energy Savings California Federal Facilities: Rate-Responsive Buidling Operating for Deeper Cost and...

  6. The Potential Benefits of Distributed Generation and the Rate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The Potential Benefits of Distributed Generation and the Rate-Related Issues That May Impede Its Expansion The Potential Benefits of Distributed Generation and the Rate-Related...

  7. Fact #659: January 24, 2011 Fuel Economy Ratings for Vehicles...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    9: January 24, 2011 Fuel Economy Ratings for Vehicles Operating on Electricity Fact 659: January 24, 2011 Fuel Economy Ratings for Vehicles Operating on Electricity The...

  8. Reaction Rates and Catalysts in Ethanol Production (1 Activity...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reaction Rates and Catalysts in Ethanol Production (1 Activity) Reaction Rates and Catalysts in Ethanol Production (1 Activity) Below is information about the student activity...

  9. Workshop on Thermonuclear Reaction Rates for Astrophysics Applications

    E-Print Network [OSTI]

    Workshop on Thermonuclear Reaction Rates for Astrophysics Applications 24-25 November 2011, Athensrd and final circular for the Workshop on Thermonuclear Reaction Rates for Astrophysics Applications

  10. Life Cycle Cost Discount Rates and Energy Price Projections ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Life Cycle Cost Discount Rates and Energy Price Projections Life Cycle Cost Discount Rates and Energy Price Projections Text file containing energy price projections underlying the...

  11. Effects of electricity rates and rate structures on pump irrigation: an eastern Colorado case study

    SciTech Connect (OSTI)

    Gardner, R.L.; Young, R.A.

    1984-11-01

    This article analyzes the effects of electricity rate policy on electricity demand (and the derived effect on irrigation water use) via a case study in eastern Colorado. Empirical demand curves for electricity for pump irrigation are estimated. Alternative rate structures are tested for their effect on electricity and water use patterns, farm income, and utility revenue. Particular attention is given to the problem of modeling a declining block structure. 11 references, 1 figure, 3 tables.

  12. K. Binder and Dieter W. Heermann Monte Carlo Method ...

    E-Print Network [OSTI]

    Heermann, Dieter W.

    - metals with quasi-free electrons and resulting phenomena such as superconductivity and the problem

  13. Recycling asphaltic concrete with sulphur as a supplemental binder 

    E-Print Network [OSTI]

    Barnett, Robert William

    1976-01-01

    ) (275'F) Ring and Ball Softening Point Specific Gravity 0. 2 mm 1. 2 mm Too Hard 14. 7 cSt 15S'F 1. 04 D 5 [53] D 5 [53] D 2170 [54] D 2170 [54] D 36 [55] D 70 [56] a Extraction ? ASTM Designation: D 2172 [57] TABLE 2--Physical... properties of the recovered aggregate. Property Fine Aggregate a b Coarse Aggregate Specific Gravity Bu11% SSD 2. 59 2. 60 Specific Gravity Apparent Absorption 2. 65 1. 4X 2. 66 1. 2X Percent Passing No. 200 Sieve S. OX ASTM Designation: C 128...

  14. ORIGINAL PAPER Chitosan hydrogel-based electrode binder and electrolyte

    E-Print Network [OSTI]

    Subramanian, Venkat

    to secondary batteries and find use in hybrid energy systems for electric vehicles, heavy-load starting assist and porosity of the electrode materials, usually comprising of activated carbons [3, 4], aerogel or xerogel

  15. Reactive binders for metal parts produced by Three Dimensional Printing

    E-Print Network [OSTI]

    Yoo, Helen Jean

    1997-01-01

    Three Dimensional Printing (3DP) is a solid free form fabrication process which enables the construction of parts directly from computer-aided design (CAD) models. In the current process, metal parts are produced by printing ...

  16. Toward an Improved Model of Asphalt Binder Oxidation in Pavements 

    E-Print Network [OSTI]

    Prapaitrakul, Nikornpon

    2011-02-22

    nd Coring of the Study ................................. 20 Table II-3. Properties of the Abilene L1 and L2 Cores ......................................... 30 Table II-4. Properties of the Abilene R1 and R2 Cores... Coring 2 nd Coring Ce11 1 5.9 Ce11 3 6.3 AC 120/150 (Un) 1992 Ce11 33 4.04 58-28 (Un) Ce11 34 3.92 58-34 (SBS) Ce11 35 I 94 3.96 58-40 (SBS) 1999 11/2004 07/2006 The accessible or interconnected air voids of core samples from the Mn...

  17. Formation of chemically bonded ceramics with magnesium dihydrogen phosphate binder

    DOE Patents [OSTI]

    Wagh, Arun S.; Jeong, Seung-Young

    2004-08-17

    A new method for combining magnesium oxide, MgO, and magnesium dihydrogen phosphate to form an inexpensive compactible ceramic to stabilize very low solubility metal oxides, ashes, swarfs, and other iron or metal-based additives, to create products and waste forms which can be poured or dye cast, and to reinforce and strengthen the ceramics formed by the addition of fibers to the initial ceramic mixture.

  18. Hazardous particle binder, coagulant and re-aerosolization inhibitor

    DOE Patents [OSTI]

    Krauter, Paula (Livermore, CA); Zalk, David (San Jose, CA); Hoffman, D. Mark (Livermore, CA)

    2011-04-12

    A copolymer and water/ethanol solvent solution capable of binding with airborne contaminants or potential airborne contaminants, such as biological weapon agents or toxic particulates, coagulating as the solvent evaporates, and adhering the contaminants to a surface so as to inhibit the re-suspension of such contaminants. The solution uses a water or ethanol/water mixture for the solvent, and a copolymer having one of several functional group sets so as to have physical and chemical characteristics of high adhesion, low viscosity, low surface tension, negative electrostatic charge, substantially neutral pH, and a low pKa. Use of the copolymer solution prevents re-aerosolization and transport of unwanted, reactive species thus increasing health and safety for personnel charged with decontamination of contaminated buildings and areas.

  19. Hazardous particle binder, coagulant and re-aerosolization inhibitor

    DOE Patents [OSTI]

    Krauter, Paula; Zalk, David; Hoffman, D. Mark

    2012-07-10

    A copolymer and water/ethanol solvent solution capable of binding with airborne contaminants or potential airborne contaminants, such as biological weapon agents or toxic particulates, coagulating as the solvent evaporates, and adhering the contaminants to a surface so as to inhibit the re-suspension of such contaminants. The solution uses a water or ethanol/water mixture for the solvent, and a copolymer having one of several functional group sets so as to have physical and chemical characteristics of high adhesion, low viscosity, low surface tension, negative electrostatic charge, substantially neutral pH, and a low pKa. Use of the copolymer solution prevents re-aerosolization and transport of unwanted, reactive species thus increasing health and safety for personnel charged with decontamination of contaminated buildings and areas.

  20. Binder Formulations Utilizing Furanic Components - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 OutreachProductswsicloudwsiclouddenDVA N C E D B L O OLaura|Bilayer Graphene Gets a BandgapBillWatch

  1. Block Copolymer Cathode Binder to Simultaneously Transport Electronic

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 OutreachProductswsicloudwsiclouddenDVA N C E D B L O OLaura|BilayerBiomimetic Dye MoleculesBlake CaseCharge and

  2. Advanced Binder for Electrode Materials | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Financing ToolInternationalReportOfficeAcqguide18pt0Department of Energy 2 DOETemperature1 DOE

  3. Advanced Binder for Electrode Materials | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Financing ToolInternationalReportOfficeAcqguide18pt0Department of Energy 2 DOETemperature1 DOE0

  4. UCRG JC-119253 PREPRINT Clean, Agile Alternative Binders, Additives and

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield MunicipalTechnicalInformation FederatedInformationTITLE:ConnectsubchittedUCID-20974UCRG

  5. Estimated recharge rates at the Hanford Site

    SciTech Connect (OSTI)

    Fayer, M.J.; Walters, T.B.

    1995-02-01

    The Ground-Water Surveillance Project monitors the distribution of contaminants in ground water at the Hanford Site for the U.S. Department of Energy. A subtask called {open_quotes}Water Budget at Hanford{close_quotes} was initiated in FY 1994. The objective of this subtask was to produce a defensible map of estimated recharge rates across the Hanford Site. Methods that have been used to estimate recharge rates at the Hanford Site include measurements (of drainage, water contents, and tracers) and computer modeling. For the simulations of 12 soil-vegetation combinations, the annual rates varied from 0.05 mm/yr for the Ephrata sandy loam with bunchgrass to 85.2 mm/yr for the same soil without vegetation. Water content data from the Grass Site in the 300 Area indicated that annual rates varied from 3.0 to 143.5 mm/yr during an 8-year period. The annual volume of estimated recharge was calculated to be 8.47 {times} 10{sup 9} L for the potential future Hanford Site (i.e., the portion of the current Site bounded by Highway 240 and the Columbia River). This total volume is similar to earlier estimates of natural recharge and is 2 to 10x higher than estimates of runoff and ground-water flow from higher elevations. Not only is the volume of natural recharge significant in comparison to other ground-water inputs, the distribution of estimated recharge is highly skewed to the disturbed sandy soils (i.e., the 200 Areas, where most contaminants originate). The lack of good estimates of the means and variances of the supporting data (i.e., the soil map, the vegetation/land use map, the model parameters) translates into large uncertainties in the recharge estimates. When combined, the significant quantity of estimated recharge, its high sensitivity to disturbance, and the unquantified uncertainty of the data and model parameters suggest that the defensibility of the recharge estimates should be improved.

  6. Binary Capture Rates for Massive Protostars

    E-Print Network [OSTI]

    Nickolas Moeckel; John Bally

    2007-04-09

    The high multiplicity of massive stars in dense, young clusters is established early in their evolution. The mechanism behind this remains unresolved. Recent results suggest that massive protostars may capture companions through disk interactions with much higher efficiency than their solar mass counterparts. However, this conclusion is based on analytic determinations of capture rates and estimates of the robustness of the resulting binaries. We present the results of coupled n-body and SPH simulations of star-disk encounters to further test the idea that disk-captured binaries contribute to the observed multiplicity of massive stars.

  7. Blazar Flaring Rates Measured with GLAST

    E-Print Network [OSTI]

    C. D. Dermer; B. L. Dingus

    2003-12-22

    We derive the minimum observing time scales to detect a blazar at a given flux level with the LAT on GLAST in the scanning and pointing modes. Based upon Phase 1 observations with EGRET, we predict the GLAST detection rate of blazar flares at different flux levels. With some uncertainty given the poor statistics of bright blazars, we predict that a blazar flare with integral flux >~ 200e-8 ph(> 100 MeV) cm^{-2} s^{-1}, which are the best candidates for Target of Opportunity pointings and extensive temporal and spectral studies, should occur every few days.

  8. Blazar Flaring Rates Measured with GLAST

    E-Print Network [OSTI]

    Dermer, C D

    2004-01-01

    We derive the minimum observing time scales to detect a blazar at a given flux level with the LAT on GLAST in the scanning and pointing modes. Based upon Phase 1 observations with EGRET, we predict the GLAST detection rate of blazar flares at different flux levels. With some uncertainty given the poor statistics of bright blazars, we predict that a blazar flare with integral flux >~ 200e-8 ph(> 100 MeV) cm^{-2} s^{-1}, which are the best candidates for Target of Opportunity pointings and extensive temporal and spectral studies, should occur every few days.

  9. Reverse Engineering of Proteasomal Translocation Rates

    E-Print Network [OSTI]

    D. S. Goldobin; M. Mishto; K. Textoris-Taube; P. M. Kloetzel; A. Zaikin

    2008-07-28

    We address the problem of proteasomal protein translocation and introduce a new stochastic model of the proteasomal digestion (cleavage) of proteins. In this model we account for the protein translocation and the positioning of cleavage sites of a proteasome from first principles. We show by test examples and by processing experimental data that our model allows reconstruction of the translocation and cleavage rates from mass spectroscopy data on digestion patterns and can be used to investigate the properties of transport in different experimental set-ups. Detailed investigation with this model will enable theoretical quantitative prediction of the proteasomal activity.

  10. Property:HeatRate | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo,AltFuelVehicle2 Jump to: navigation, search ThisHeadquartersState Jump to:HeatRate Jump

  11. BPA Power Rates (pbl/main)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room News PublicationsAudits & Inspections Audits Generation Hydro Power Wind Power MonthlyRates

  12. utility rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX E LIST OFAMERICA'SHeavyAgencyTendo NewYanbu, Saudideveloper Homeroadmap Homeutility rate

  13. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Home > Utility

  14. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Home >

  15. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Home >Utility

  16. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Home >UtilityUtility

  17. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Home

  18. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Homecommercial load

  19. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate Homecommercial

  20. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate HomecommercialUtility

  1. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility Rate

  2. Utility Rate | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThin FilmUnited States:UserLaborUtility RateUtility

  3. Adding International Rates | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EAand DaltonSolar Energy LLC JumpInformationAdding International Rates

  4. Category:Utility Rates | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmentalBowerbank,CammackFLIR Jump to:RAPID RoadmapInformation Utility Rate Impacts on

  5. Utility-Based Wireless Resource Allocation for Variable Rate Transmission

    E-Print Network [OSTI]

    Zhang, Xiaolu; Ng, Chun Sum

    2007-01-01

    For most wireless services with variable rate transmission, both average rate and rate oscillation are important performance metrics. The traditional performance criterion, utility of average transmission rate, boosts the average rate but also results in high rate oscillations. We introduce a utility function of instantaneous transmission rates. It is capable of facilitating the resource allocation with flexible combinations of average rate and rate oscillation. Based on the new utility, we consider the time and power allocation in a time-shared wireless network. Two adaptation policies are developed, namely, time sharing (TS) and joint time sharing and power control (JTPC). An extension to quantized time sharing with limited channel feedback (QTSL) for practical systems is also discussed. Simulation results show that by controlling the concavity of the utility function, a tradeoff between the average rate and rate oscillation can be easily made.

  6. Directional recoil rates for WIMP direct detection

    SciTech Connect (OSTI)

    Alenazi, Moqbil S.; Gondolo, Paolo [Department of Physics, University of Utah, 115 S 1400 E Rm 201, Salt Lake City, Utah 84112-0830 (United States)

    2008-02-15

    New techniques for the laboratory direct detection of dark matter weakly interacting massive particles (WIMPs) are sensitive to the recoil direction of the struck nuclei. We compute and compare the directional recoil rates dR/dcos{theta} (where {theta} is the angle measured from a reference direction in the sky) for several WIMP velocity distributions including the standard dark halo and anisotropic models such as Sikivie's late-infall halo model and logarithmic-ellipsoidal models. Since some detectors may be unable to distinguish the beginning of the recoil track from its end (lack of head-tail discrimination), we introduce a folded directional recoil rate dR/d|cos{theta}|, where |cos{theta}| does not distinguish the head from the tail of the track. We compute the CS{sub 2} and CF{sub 4} exposures required to distinguish a signal from an isotropic background noise, and find that dR/d|cos{theta}| is effective for the standard dark halo and some but not all anisotropic models.

  7. Relationship Between Surface Free Energy and Total Work of Fracture of Asphalt Binder and Asphalt Binder-Aggregate Interfaces 

    E-Print Network [OSTI]

    Howson, Jonathan Embrey

    2012-10-19

    Performance of asphalt mixtures depends on the properties of its constituent materials, mixture volumetrics, and external factors such as load and environment. An important material property that influences the performance ...

  8. Workshop on Thermonuclear Reaction Rates for Astrophysics Applications

    E-Print Network [OSTI]

    Workshop on Thermonuclear Reaction Rates for Astrophysics Applications 24-25 November 2011, Athens circular for the Workshop on Thermonuclear Reaction Rates for Astrophysics Applications, to be held of thermonuclear reaction rates. The topics of the workshop, in relation with thermonuclear reaction rates

  9. Case Study 1: Adjustable-Rate Home Mortgage Loan

    E-Print Network [OSTI]

    Colton, Jonathan S.

    . The disadvantage is that lenders usually charge a higher interest rate for these loans than for adjustable rate, and they are used by lenders to determine the mortgage loans's new interest rate at the time of adjustment. The two lenders use one-year T-bill yields as their indexes. The T-bill rate tends to uctuate much more

  10. Rates and progenitors of type Ia supernovae

    SciTech Connect (OSTI)

    Wood-Vasey, William Michael

    2004-08-16

    The remarkable uniformity of Type Ia supernovae has allowed astronomers to use them as distance indicators to measure the properties and expansion history of the Universe. However, Type Ia supernovae exhibit intrinsic variation in both their spectra and observed brightness. The brightness variations have been approximately corrected by various methods, but there remain intrinsic variations that limit the statistical power of current and future observations of distant supernovae for cosmological purposes. There may be systematic effects in this residual variation that evolve with redshift and thus limit the cosmological power of SN Ia luminosity-distance experiments. To reduce these systematic uncertainties, we need a deeper understanding of the observed variations in Type Ia supernovae. Toward this end, the Nearby Supernova Factory has been designed to discover hundreds of Type Ia supernovae in a systematic and automated fashion and study them in detail. This project will observe these supernovae spectrophotometrically to provide the homogeneous high-quality data set necessary to improve the understanding and calibration of these vital cosmological yardsticks. From 1998 to 2003, in collaboration with the Near-Earth Asteroid Tracking group at the Jet Propulsion Laboratory, a systematic and automated searching program was conceived and executed using the computing facilities at Lawrence Berkeley National Laboratory and the National Energy Research Supercomputing Center. An automated search had never been attempted on this scale. A number of planned future large supernovae projects are predicated on the ability to find supernovae quickly, reliably, and efficiently in large datasets. A prototype run of the SNfactory search pipeline conducted from 2002 to 2003 discovered 83 SNe at a final rate of 12 SNe/month. A large, homogeneous search of this scale offers an excellent opportunity to measure the rate of Type Ia supernovae. This thesis presents a new method for analyzing the true sensitivity of a multi-epoch supernova search and finds a Type Ia supernova rate from z {approx} 0.01-0.1 of r{sub V} = 4.26{sub -1.93 -0.10}{sup +1.39 +0.10} h{sup 3} x 10{sup -4} SNe Ia/yr/Mpc{sup 3} from a preliminary analysis of a subsample of the SNfactory prototype search. Several unusual supernovae were found in the course of the SNfactory prototype search. One in particular, SN 2002ic, was the first SN Ia to exhibit convincing evidence for a circumstellar medium and offers valuable insight into the progenitors of Type Ia supernovae.

  11. Extremum seeking with bounded update rates

    SciTech Connect (OSTI)

    Scheinker, Alexander; Krsti?, Miroslav

    2013-11-16

    In this work, we present a form of extremum seeking (ES) in which the unknown function being minimized enters the system’s dynamics as the argument of a cosine or sine term, thereby guaranteeing known bounds on update rates and control efforts. We present general n-dimensional optimization and stabilization results as well as 2D vehicle control, with bounded velocity and control efforts. For application to autonomous vehicles, tracking a source in a GPS denied environment with unknown orientation, this ES approach allows for smooth heading angle actuation, with constant velocity, and in application to a unicycle-type vehicle results in control ability as if the vehicle is fully actuated. Our stability analysis is made possible by the classic results of Kurzweil, Jarnik, Sussmann, and Liu, regarding systems with highly oscillatory terms. In our stability analysis, we combine the averaging results with a semi-global practical stability result under small parametric perturbations developed by Moreau and Aeyels.

  12. Power Spectrum Analyses of Nuclear Decay Rates

    E-Print Network [OSTI]

    Javorsek, D; Lasenby, R N; Lasenby, A N; Buncher, J B; Fischbach, E; Gruenwald, J T; Hoft, A W; Horan, T J; Jenkins, J H; Kerford, J L; Lee, R H; Longman, A; Mattes, J J; Morreale, B L; Morris, D B; Mudry, R N; Newport, J R; O'Keefe, D; Petrelli, M A; Silver, M A; Stewart, C A; Terry, B; 10.1016/j.astropartphys.2010.06.011

    2010-01-01

    We provide the results from a spectral analysis of nuclear decay data displaying annually varying periodic fluctuations. The analyzed data were obtained from three distinct data sets: 32Si and 36Cl decays reported by an experiment performed at the Brookhaven National Laboratory (BNL), 56Mn decay reported by the Children's Nutrition Research Center (CNRC), but also performed at BNL, and 226Ra decay reported by an experiment performed at the Physikalisch-Technische Bundesanstalt (PTB) in Germany. All three data sets exhibit the same primary frequency mode consisting of an annual period. Additional spectral comparisons of the data to local ambient temperature, atmospheric pressure, relative humidity, Earth-Sun distance, and their reciprocals were performed. No common phases were found between the factors investigated and those exhibited by the nuclear decay data. This suggests that either a combination of factors was responsible, or that, if it was a single factor, its effects on the decay rate experiments are n...

  13. WP-96/TR-96 & TC-96 Power and Transmission Rate Case (rates/ratecases)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust,Field-effectWorking WithTelecentricN A 035(92/02) nerg *415,Rates > MeetingsRates >

  14. Basics of Chemical Kinetics -1 Rate of reaction = rate of disappearance of A =

    E-Print Network [OSTI]

    Albert, Réka

    reactions: Forward Reaction Backward Reaction CBA + 2 CBA + 2 CBA + 2 CBA + 2 #12;Basics of Chemical], [C] CBA + #12;Ex. 1 Determine the relation between the reaction rates and the reaction flux. Assume conservation. Hint: think of the reaction as a complex formation CBA + ]B][A[k dt ]C[d =]B][A[k dt ]B[d dt ]A

  15. Rate constants from the reaction path Hamiltonian. I. Reactive flux simulations for dynamically correct rates

    E-Print Network [OSTI]

    Bell, Alexis T.

    As ab initio electronic structure calculations become more accurate, inherent sources of error, facilitate reactive flux calculations. As an example we compute the dynamically corrected rate constant on which the reaction occurs. A large number of electronic structure theo- ries are available

  16. An Examination of Harvest Rates and Brood-Take Rates as

    E-Print Network [OSTI]

    ;iv Abstract The Cowichan River fall-run Chinook salmon (Oncorhynchus tshawytscha) population has been of Cowichan River Chinook Salmon by Athena Dawn Ogden Ph.D., University of British Columbia, 2002 B.A. (Hons-Take Rates as Management Strategies to Assist Recovery of Cowichan River Chinook Salmon Examining Committee

  17. Solids flow rate measurement in dense slurries

    SciTech Connect (OSTI)

    Porges, K.G.; Doss, E.D.

    1993-09-01

    Accurate and rapid flow rate measurement of solids in dense slurries remains an unsolved technical problem, with important industrial applications in chemical processing plants and long-distance solids conveyance. In a hostile two-phase medium, such a measurement calls for two independent parameter determinations, both by non-intrusive means. Typically, dense slurries tend to flow in laminar, non-Newtonian mode, eliminating most conventional means that usually rely on calibration (which becomes more difficult and costly for high pressure and temperature media). These issues are reviewed, and specific solutions are recommended in this report. Detailed calculations that lead to improved measuring device designs are presented for both bulk density and average velocity measurements. Cross-correlation, chosen here for the latter task, has long been too inaccurate for practical applications. The cause and the cure of this deficiency are discussed using theory-supported modeling. Fluid Mechanics are used to develop the velocity profiles of laminar non-Newtonian flow in a rectangular duct. This geometry uniquely allows the design of highly accurate `capacitive` devices and also lends itself to gamma transmission densitometry on an absolute basis. An absolute readout, though of less accuracy, is also available from a capacitive densitometer and a pair of capacitive sensors yields signals suitable for cross-correlation velocity measurement.

  18. Extremum seeking with bounded update rates

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Scheinker, Alexander; Krsti?, Miroslav

    2013-11-16

    In this work, we present a form of extremum seeking (ES) in which the unknown function being minimized enters the system’s dynamics as the argument of a cosine or sine term, thereby guaranteeing known bounds on update rates and control efforts. We present general n-dimensional optimization and stabilization results as well as 2D vehicle control, with bounded velocity and control efforts. For application to autonomous vehicles, tracking a source in a GPS denied environment with unknown orientation, this ES approach allows for smooth heading angle actuation, with constant velocity, and in application to a unicycle-type vehicle results in control abilitymore »as if the vehicle is fully actuated. Our stability analysis is made possible by the classic results of Kurzweil, Jarnik, Sussmann, and Liu, regarding systems with highly oscillatory terms. In our stability analysis, we combine the averaging results with a semi-global practical stability result under small parametric perturbations developed by Moreau and Aeyels.« less

  19. Power Spectrum Analyses of Nuclear Decay Rates

    E-Print Network [OSTI]

    D. Javorsek II; P. A. Sturrock; R. N. Lasenby; A. N. Lasenby; J. B. Buncher; E. Fischbach; J. T. Gruenwald; A. W. Hoft; T. J. Horan; J. H. Jenkins; J. L. Kerford; R. H. Lee; A. Longman; J. J. Mattes; B. L. Morreale; D. B. Morris; R. N. Mudry; J. R. Newport; D. O'Keefe; M. A. Petrelli; M. A. Silver; C. A. Stewart; B. Terry

    2010-07-06

    We provide the results from a spectral analysis of nuclear decay data displaying annually varying periodic fluctuations. The analyzed data were obtained from three distinct data sets: 32Si and 36Cl decays reported by an experiment performed at the Brookhaven National Laboratory (BNL), 56Mn decay reported by the Children's Nutrition Research Center (CNRC), but also performed at BNL, and 226Ra decay reported by an experiment performed at the Physikalisch-Technische Bundesanstalt (PTB) in Germany. All three data sets exhibit the same primary frequency mode consisting of an annual period. Additional spectral comparisons of the data to local ambient temperature, atmospheric pressure, relative humidity, Earth-Sun distance, and their reciprocals were performed. No common phases were found between the factors investigated and those exhibited by the nuclear decay data. This suggests that either a combination of factors was responsible, or that, if it was a single factor, its effects on the decay rate experiments are not a direct synchronous modulation. We conclude that the annual periodicity in these data sets is a real effect, but that further study involving additional carefully controlled experiments will be needed to establish its origin.

  20. Uncertainty analysis of multi-rate kinetics of uranium desorption...

    Office of Scientific and Technical Information (OSTI)

    multi-rate kinetics of uranium desorption from sediments A multi-rate expression for uranyl U(VI) surface complexation reactions has been proposed to describe diffusion-limited...

  1. Tips: Time-Based Electricity Rates | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tips: Time-Based Electricity Rates Tips: Time-Based Electricity Rates July 27, 2014 - 8:09pm Addthis Time-based electricity programs encourage you to use energy when the demand is...

  2. Energy Productivity Via Time-of-Day Rates 

    E-Print Network [OSTI]

    Michael, R. S.

    1984-01-01

    Prompted by a combination of PURPA and a national concern about electricity price and supply, many utilities now have in place industrial time-of-day electric rates. When properly designed, these rates present an opportunity for energy...

  3. Inflation targeting in emerging countries: the exchange rate issues 

    E-Print Network [OSTI]

    Reyes Altamirano, Javier Arturo

    2004-09-30

    The current discussion of Inflation Targeting (IT) in emerging economies deals with the effects that nominal exchange rate movements have on the overall inflation rate. The literature has focused in the analysis of the ...

  4. Apply: Increase Residential Energy Code Compliance Rates (DE...

    Energy Savers [EERE]

    Apply: Increase Residential Energy Code Compliance Rates (DE-FOA-0000953) Apply: Increase Residential Energy Code Compliance Rates (DE-FOA-0000953) April 21, 2014 - 12:32pm Addthis...

  5. Loading rate dependence of permeability evolution in porous aeolian sandstones 

    E-Print Network [OSTI]

    Ojala, Ira O; Ngwenya, Bryne T; Main, Ian G

    2004-01-01

    Mechanical properties of rocks are characterized by their notable dependence on the applied deformation rate. However, little is known about the strain rate dependence of fluid flow properties since most laboratory tests ...

  6. AIR LEAKAGE, SURFACE PRESSURES AND INFILTRATION RATES IN HOUSES

    E-Print Network [OSTI]

    Grimsrud, D.T.

    2011-01-01

    Infiltration Effects on Energy in Housing " Center for Environmental Studiesair infiltration rate as measured. As part of this study,

  7. The role of observer individual differences in personality assessments of the domesticated horse: A novel application of Kelly’s Repertory Grid Technique 

    E-Print Network [OSTI]

    Grajfoner, Daša

    2007-01-01

    Consistent personality differences (e.g. shyness, sociability) among animals have been frequently reported by scientists. Such information used to be considered unscientific, even though it was widely used to describe ...

  8. Rate Control Management of Atrial Fibrillation: May a Mathematical Model Suggest an Ideal Heart Rate?

    E-Print Network [OSTI]

    Anselmino, Matteo; Camporeale, Carlo; Saglietto, Andrea; Gaita, Fiorenzo; Ridolfi, Luca

    2015-01-01

    Background. Despite the routine prescription of rate control therapy for atrial fibrillation (AF), clinical evidence demonstrating a heart rate target is lacking. Aim of the present study was to run a mathematical model simulating AF episodes with a different heart rate (HR) to predict hemodynamic parameters for each situation. Methods. The lumped model, representing the pumping heart together with systemic and pulmonary circuits, was run to simulate AF with HR of 50, 70, 90, 110 and 130 bpm, respectively. Results. Left ventricular pressure increased by 56.7%, from 33.92+-37.56 mmHg to 53.15+-47.56 mmHg, and mean systemic arterial pressure increased by 27.4%, from 82.66+-14.04 mmHg to 105.29+-7.63 mmHg, at the 50 and 130 bpm simulations, respectively. Stroke volume (from 77.45+-8.5 to 39.09+-8.08 mL), ejection fraction (from 61.1+-4.4 to 39.32+-5.42%) and stroke work (SW, from 0.88+-0.04 to 0.58+-0.09 J) decreased by 49.5, 35.6 and 34.2%, at the 50 and 130 bpm simulations, respectively. In addition, oxygen co...

  9. Chukwuemeka I. Okoye Carbon Dioxide Solubility and Absorption Rate in

    E-Print Network [OSTI]

    Rochelle, Gary T.

    Copyright by Chukwuemeka I. Okoye 2005 #12;Carbon Dioxide Solubility and Absorption Rate _______________________ Nicholas A. Peppas #12;Carbon Dioxide Solubility and Absorption Rate in Monoethanolamine/Piperazine/H2O for. #12;iii Carbon Dioxide Solubility and Absorption Rate in Monoethanolamine/Piperazine/H2O

  10. Rate Adaptation in MIMO Antenna Selection System with Imperfect CSIT

    E-Print Network [OSTI]

    Bhashyam, Srikrishna

    constant power and rate will lead to block errors during the poor channel conditions or under utilization that encompasses feedback delay, estimation errors and prediction. However, rate adaptation has not been consideredRate Adaptation in MIMO Antenna Selection System with Imperfect CSIT T. R. Ramya and Srikrishna

  11. EIS-0093: Bonneville Power Administration's 1982 Rate Proposal

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy's Bonneville Power Administration prepared this statement to evaluate the potential environmental impacts associated with an increase in wholesale power rates for calendar year 1982, including the effects of rate hikes in that year, the cumulative effects of rate hikes from 1979-1985, as well as alternative revenue scenarios.

  12. Spontaneous emission rates of dipoles in photonic crystal membranes

    E-Print Network [OSTI]

    Spontaneous emission rates of dipoles in photonic crystal membranes A. Femius Koenderink Laboratory-difference time-domain calculations show over 7 times inhibition and 15 times enhancement of the emission rate compared with vacuum for judi- ciously oriented and positioned dipoles. Emission rate modifications inside

  13. Cosmogenic 3 He production rates from Holocene lava flows

    E-Print Network [OSTI]

    Licciardi, Joseph M.

    rights reserved. Keywords: cosmogenic nuclides; helium; production rates; Icelandic Low; surface exposureCosmogenic 3 He production rates from Holocene lava flows in Iceland J.M. Licciardi a,, M.D. Kurz b Available online 25 April 2006 Editor: K. Farley Abstract We measured cosmogenic 3 He production rates

  14. EIS-0102: Bonneville Power Administration's 1983 Wholesale Power Rate

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy's Bonneville Power Administration prepared this EIS to evaluate the potential environmental impacts associated with an increase in wholesale power rates that would become effective on November 1, 1983, including the effects of rate hikes in that year and the cumulative effects of previous rate hikes.

  15. Interest Rate Clustering in UK Financial Services Markets

    E-Print Network [OSTI]

    Feigon, Brooke

    clustering in retail markets, through an examination of how interest rates cluster in two UK financial services markets. It is proposed that price or interest rate clustering forms in retail markets as firms1 Interest Rate Clustering in UK Financial Services Markets by John K. Ashton Norwich Business

  16. Exports and exchange rate : a firm-level investigation

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Exports and exchange rate : a firm-level investigation N° 2008-02 Février 2008 Sarah Guillou OFCE-DRIC hal-00973044,version1-3Apr2014 #12;Exports and exchange rate: a firm-level investigation Sarah Guillou February 2008 Abstract This paper investigates the relation between export behaviour and the exchange rate

  17. 2015-2016 HOUSING RATES Upperclassmen and Transfer Students

    E-Print Network [OSTI]

    Elzanowski, Marek

    2015-2016 HOUSING RATES Upperclassmen and Transfer Students 1977 SW 6TH AVE , SUITE 210 PORTLAND, OR 97201 PHONE: 503.725.4375 EMAIL: HOUSING@PDX.EDU WWW.PDX.EDU/HOUSING UNIVERSITY HOUSING OPTIONS RATES with no other roommate you will be charged the single rate and Housing will not assign anyone else to that unit

  18. Housing Rates 2015 Susan B. Anthony Summer Housing

    E-Print Network [OSTI]

    Cantlon, Jessica F.

    Page 1 Housing Rates 2015 Susan B. Anthony Summer Housing Summer housing rates are discounted (seven days). We do not offer a per night rate. Summer housing applications will be accepted from April 8 Note: Housing Dates are generally a day before and a day after the session. You may indicate additional

  19. ARC: An Integrated Admission and Rate Control Framework for Competitive

    E-Print Network [OSTI]

    Chatterjee, Mainak

    . The implementation of Wireless Local Number Portability (WLNP) is expected to further increase the churn rate (the construct its game strategy set so as to maximize their utility (revenue) considering the churn rate. Based, even higher churn rate is predicted [38]. In fact, the statistics from 2003 show that most wireless

  20. A Competitive Rate Allocation Game Yanting Wu1

    E-Print Network [OSTI]

    Krishnamachari, Bhaskar

    , the transmitter sends data at a low rate R1 over both channels. And when both receivers bid high, the transmitter splits its power to send data at a high rate R2 over both channels. When one of the receivers bids low and the other bids high, the transmitter sends data at a very high rate R3 over the latter channel. When

  1. CONFIDENCE LIMITS FOR POPULATION PROJECTIONS WHEN VITAL RATES VARY RANDOMLY

    E-Print Network [OSTI]

    CONFIDENCE LIMITS FOR POPULATION PROJECTIONS WHEN VITAL RATES VARY RANDOMLY TIM GERRODE, age distribution, and vital rates are known (e.g., Leslie 1945; Keyfitz 1968). Such population rates are available. However, there is uncertainty in such projections. First, we rarely know vital

  2. ADJECTIVE RATINGS FOR FIRE BEHAVIOR For many years now in America we have used the National Fire Danger Rating System

    E-Print Network [OSTI]

    Danger Rating System (Deeming, et al, 1978) adjective ratings to describe the "fire danger" for a given of descriptive advice of the "danger" of having an ignition based on historic weather data for what kind of fire these ratings meant regarding potential fire behavior. Furthermore, they described "fire danger" which

  3. ADITYA KARNIK: PERFORMANCE OF TCP WITH EXPLICIT RATE FEEDBACK 1 Performance of TCP Congestion Control with Explicit Rate Feedback

    E-Print Network [OSTI]

    Kumar, Anurag

    directly to the individual TCP sources, and study a policy for utilizing this rate information in TCP on this rate feed­ back and a round­trip­time (RTT) estimate. Thus our concern in this paper is to studyADITYA KARNIK: PERFORMANCE OF TCP WITH EXPLICIT RATE FEEDBACK 1 Performance of TCP Congestion

  4. HIgh Rate X-ray Fluorescence Detector

    SciTech Connect (OSTI)

    Grudberg, Peter Matthew [XIA LLC

    2013-04-30

    The purpose of this project was to develop a compact, modular multi-channel x-ray detector with integrated electronics. This detector, based upon emerging silicon drift detector (SDD) technology, will be capable of high data rate operation superior to the current state of the art offered by high purity germanium (HPGe) detectors, without the need for liquid nitrogen. In addition, by integrating the processing electronics inside the detector housing, the detector performance will be much less affected by the typically noisy electrical environment of a synchrotron hutch, and will also be much more compact than current systems, which can include a detector involving a large LN2 dewar and multiple racks of electronics. The combined detector/processor system is designed to match or exceed the performance and features of currently available detector systems, at a lower cost and with more ease of use due to the small size of the detector. In addition, the detector system is designed to be modular, so a small system might just have one detector module, while a larger system can have many â?? you can start with one detector module, and add more as needs grow and budget allows. The modular nature also serves to simplify repair. In large part, we were successful in achieving our goals. We did develop a very high performance, large area multi-channel SDD detector, packaged with all associated electronics, which is easy to use and requires minimal external support (a simple power supply module and a closed-loop water cooling system). However, we did fall short of some of our stated goals. We had intended to base the detector on modular, large-area detectors from Ketek GmbH in Munich, Germany; however, these were not available in a suitable time frame for this project, so we worked instead with pnDetector GmbH (also located in Munich). They were able to provide a front-end detector module with six 100 m^2 SDD detectors (two monolithic arrays of three elements each) along with associated preamplifiers; these detectors surpassed the performance we expected to get from the Ketek detectors, however they are housed in a sealed module, which does not offer the ease of repair and expandability weâ??d hoped to achieve with the Ketek SDDâ??s. Our packaging efforts were quite successful, as we came up with a very compact way to mount the detector and to house the associated electronics, as well as a very effective way to reliably take out the heat (from the electronics as well as the detectorâ??s Peltier coolers) without risk of condensation and without external airflow or vibration, which could create problems for the target applications. While we were able to design compact processing electronics that fit into the detector assembly, they are still at the prototype stage, and would require a significant redesign to achieve product status. We have not yet tested this detector at a synchrotron facility; we do still plan on working with some close contacts at the nearby Stanford Synchrotron Radiation Laboratory (SSRL) to get some testing with the beam (using existing commercial electronics for readout, as the integrated processor is not ready for use).

  5. Property:OpenEI/UtilityRate/DemandRateStructure/Tier5Adjustment | Open

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo,AltFuelVehicle2 JumpPublicationDate Jump to:InformationEnergyInformation Rate

  6. Radiation dose rates from UF{sub 6} cylinders

    SciTech Connect (OSTI)

    Friend, P.J. [Urenco, Capenhurst (United Kingdom)

    1991-12-31

    This paper describes the results of many studies, both theoretical and experimental, which have been carried out by Urenco over the last 15 years into radiation dose rates from uranium hexafluoride (UF{sub 6}) cylinders. The contents of the cylinder, its history, and the geometry all affect the radiation dose rate. These factors are all examined in detail. Actual and predicted dose rates are compared with levels permitted by IAEA transport regulations.

  7. Charged-Particle Thermonuclear Reaction Rates: III. Nuclear Physics Input

    E-Print Network [OSTI]

    Christian Iliadis; Richard Longland; Art Champagne; Alain Coc

    2010-04-23

    The nuclear physics input used to compute the Monte Carlo reaction rates and probability density functions that are tabulated in the second paper of this series (Paper II) is presented. Specifically, we publish the input files to the Monte Carlo reaction rate code RatesMC, which is based on the formalism presented in the first paper of this series (Paper I). This data base contains overwhelmingly experimental nuclear physics information. The survey of literature for this review was concluded in November 2009.

  8. Recovery Efficiency, False Negative Rate, and Limit of Detection...

    Office of Scientific and Technical Information (OSTI)

    Recovery Efficiency, False Negative Rate, and Limit of Detection Performance of a Validated Macrofoam-Swab Sampling Method with Low Surface Concentrations of Two Bacillus anthracis...

  9. Energy Performance Ratings for Windows, Doors, and Skylights...

    Office of Environmental Management (EM)

    The ability of glazing in a window, door, or skylight to transmit sunlight into a home can be measured and rated according to the following energy performance...

  10. Control Strategies for Centrifugal Pumps with Variable Flow Rate...

    Broader source: Energy.gov (indexed) [DOE]

    This tip sheet discusses control strategies for centrifugal pumps with variable flow rate requirements in pumping systems and includes installation considerations. PUMPING SYSTEMS...

  11. Control Strategies for Centrifugal Pumps with Variable Flow Rate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    pumping applications with variable flow rate requirements, adjustable speed drives (ASDs) are an efficient control alternative to throttling or bypass methods. ASDs save energy by...

  12. Construction, Qualification, and Low Rate Production Start-up...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Facility with Capacity to Support 100,000 Electric Drive Vehicles Construction, Qualification, and Low Rate Production Start-up of a DC Bus Capacitor High Volume...

  13. Figure 6. Projected Production for the Low Development Rate of...

    U.S. Energy Information Administration (EIA) Indexed Site

    6. Projected Production for the Low Development Rate of Technically Recoverable Oil Estimated at 5 Percent, Mean, and 95 Percent Probabilities for the ANWR Coastal Plain of the...

  14. Estimation of Gas Leak Rates Through Very Small Orifices

    Office of Scientific and Technical Information (OSTI)

    Estimation of Gas Leak Rates Through Very Small Orifices and Channels by Herbert J. Bomelburg February 1977 Prepared for the Nuclear Regulatory Commission -..- Pacific Northwest...

  15. Integrated System Transmission and Ancillary Services Rate Calculation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Gross receipts taxes are not included in transmission revenue requirement in the Rate Formula Template, since they are recovered elsewhere. I Western is not subject to Federal or...

  16. Microsoft Word - Notice - Rate Order Signed.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Ancillary Services and Transmission Service Penalty for Unreserved Use Formula Rates into effect on an interim basis on January 1, 2010. The Federal Register notice...

  17. Integrated System Transmission and Ancillary Services Rate Calculation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Western Area Power Administration Basin Electric Power Cooperative Heartland Consumers Power District 1 Integrated System Transmission and Ancillary Services Rate Calculation...

  18. Integrated System Transmission and Ancillary Services Rate Calculation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    System Transmission and Ancillary Services 2013 Rate True-up Calculation Western Area Power Administration Basin Electric Power Cooperative Heartland Consumers Power District 1...

  19. DOE Commercial Building Energy Asset Rating Program Focus Groups...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ssetratingseattlefocusgroups.pdf More Documents & Publications Commercial Building Energy Asset Rating Workshop A Common Definition for Zero Energy Buildings Building Energy...

  20. Resuspension rates from aged inert-tracer sources

    SciTech Connect (OSTI)

    Sehmel, G.A.

    1982-11-01

    Wind-caused particle resuspension rates were investigated with molybdenum tracers at two circular resuspension sites in the Hanford area. The tracer particles were calcium molybdate. The radii of each circular tracer-source area were 22.9 m and 29.9 m respectively for tracer deposited on 2 October 1973 and 29 May 1979. Resuspension rates were investigated by sampling resuspended tracer with air sampling equipment mounted as a function of height on a centrally located sampling tower at each site. Sampling equipment was operated as a function of wind speed increments in order to investigate resuspension rates, wind speed dependencies of resuspension rates, and for subsequent comparisons of resuspension rate changes as a function of time for constant wind speed ranges. Experimental results are reported for measurements over several years. Resuspension rates ranged from about 10/sup -13/ to 10/sup -6/ fraction of the tracer source resuspended per second. Resuspension rates tended to increase with increasing wind speed. At one investigation site, resuspension rates were nearly constant, except for seasonal variations, for a four-year time period. Resuspension rates appear higher in the autumn than in the spring and summer.

  1. Conducting Quantitative Electrochemistry on a TEM to Study Rate...

    Office of Scientific and Technical Information (OSTI)

    Conducting Quantitative Electrochemistry on a TEM to Study Rate Dependencies in the Reversible Lithiation of Silicon Nanowires. Citation Details In-Document Search Title:...

  2. BPA proposes rate increase to bolster federal power and transmission...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Northwest consumer-owned utilities including public utility districts, tribal utilities, cooperatives, municipalities and federal entities. Transmission rates If adopted, this...

  3. ORISE: Report shows nuclear engineering graduation rates leveling...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ORISE report shows nuclear engineering graduation rates leveling off in 2014 after five years of increase Decline seen in undergraduate and master degrees, while number of doctoral...

  4. ORISE: Report shows nuclear engineering graduation rates on the...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ORISE report shows nuclear engineering graduation rates on the rise in 2013 Number of graduate degrees expected to remain consistent, but undergraduate degrees could see decrease...

  5. Power and rate allocation for video conferencing in cellular networks

    E-Print Network [OSTI]

    Yang, Chao; Jordan, Scott

    2013-01-01

    on power allocation when utility is a function of theallocation method that uses sigmoid utility functions (functions can be used to accomplish di?erentiated rate allocation.

  6. Certification and Rating of Attachments for Fenestration Technologies...

    Office of Environmental Management (EM)

    The successful applicant will also develop a Program to rate fenestration attachment energy performance and provide accurate and useful product comparison criteria, allowing...

  7. EERE Peer Review Guide, Appendix K Sample Rating Summary Sheet

    SciTech Connect (OSTI)

    None

    2009-01-18

    A peer review sample summary rating sheet, from the September 2002 The Peer Review Process Handbook, an Implementation Manual based on the Superconductivity Program Experience.

  8. ENERGY STAR Webinar: ENERGY STAR and Green Building Rating Systems...

    Broader source: Energy.gov (indexed) [DOE]

    resources to help meet requirements for green building rating systems, such as the U.S. Green Building Council's Leadership in Energy and Environmental Design (LEED), the Green...

  9. Formaldehyde as a basis for residential ventilation rates

    E-Print Network [OSTI]

    Sherman, M.H.; Hodgson, A.T.

    2002-01-01

    Quality Guideline No. 1. Formaldehyde in the Home. ResearchIn press) “Sources of formaldehyde, other aldehydes andJ. (1999) “Emission rates of formaldehyde from materials and

  10. Energy Performance Ratings for Windows, Doors, and Skylights...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The higher the number, the more light transmitted without adding excessive amounts of heat. This energy performance rating isn't always provided. Learn More Energy-Efficient...

  11. The growth rate of gas hydrate from refrigerant R12

    SciTech Connect (OSTI)

    Kendoush, Abdullah Abbas; Jassim, Najim Abid [Centre of Engineering Physics, Ministry of Sciences and Technology, P.O. Box 765, Baghdad (Iraq); Joudi, Khalid A. [Al-Nahrain University, Baghdad (Iraq)

    2006-07-15

    Experimental and theoretical investigations were presented dealing with three phase direct-contact heat transfer by evaporation of refrigerant drops in an immiscible liquid. Refrigerant R12 was used as the dispersed phase, while water and brine were the immiscible continuous phase. A numerical solution is presented to predict the formation rate of gas hydrates in test column. The solution provided an acceptable agreement when compared with experimental results. The gas hydrate growth rate increased with time. It increased with increasing dispersed phase flow rate. The presence of surface-active sodium chloride in water had a strong inhibiting effect on the gas hydrate formation rate. (author)

  12. Longshore sediment transport rate calculated incorporating wave orbital velocity fluctuations 

    E-Print Network [OSTI]

    Smith, Ernest Ray

    2006-10-30

    Laboratory experiments were performed to study and improve longshore sediment transport rate predictions. Measured total longshore transport in the laboratory was approximately three times greater for plunging breakers ...

  13. Electricity Rate Structures and the Economics of Solar PV: Could Mandatory Time-of-Use Rates Undermine California’s Solar Photovoltaic Subsidies?

    E-Print Network [OSTI]

    Borenstein, Severin

    2007-01-01

    CSEM WP 172 Electricity Rate Structures and the Economics of94720-5180 www.ucei.org Electricity Rate Structures and thefuture of California electricity rate levels and rate design

  14. Charged-Particle Thermonuclear Reaction Rates: II. Tables and Graphs of Reaction Rates and Probability Density Functions

    E-Print Network [OSTI]

    Christian Iliadis; Richard Longland; Art Champagne; Alain Coc; Ryan Fitzgerald

    2010-04-23

    Numerical values of charged-particle thermonuclear reaction rates for nuclei in the A=14 to 40 region are tabulated. The results are obtained using a method, based on Monte Carlo techniques, that has been described in the preceding paper of this series (Paper I). We present a low rate, median rate and high rate which correspond to the 0.16, 0.50 and 0.84 quantiles, respectively, of the cumulative reaction rate distribution. The meaning of these quantities is in general different from the commonly reported, but statistically meaningless expressions, "lower limit", "nominal value" and "upper limit" of the total reaction rate. In addition, we approximate the Monte Carlo probability density function of the total reaction rate by a lognormal distribution and tabulate the lognormal parameters {\\mu} and {\\sigma} at each temperature. We also provide a quantitative measure (Anderson-Darling test statistic) for the reliability of the lognormal approximation. The user can implement the approximate lognormal reaction rate probability density functions directly in a stellar model code for studies of stellar energy generation and nucleosynthesis. For each reaction, the Monte Carlo reaction rate probability density functions, together with their lognormal approximations, are displayed graphically for selected temperatures in order to provide a visual impression. Our new reaction rates are appropriate for bare nuclei in the laboratory. The nuclear physics input used to derive our reaction rates is presented in the subsequent paper of this series (Paper III). In the fourth paper of this series (Paper IV) we compare our new reaction rates to previous results.

  15. Abstract--Standard and routine metabolic rates (SMRs and RMRs,

    E-Print Network [OSTI]

    and to recovery of other coastal shark stocks (Branstetter, 1990). Bioenergetics models can be used to assess accu- rately in order to construct realistic bioenergetics models (Ney, 1993). Systematic metabolic bioenergetics have relied upon metabolic rate data from unrelated species (Medved et al., 1988; Stillwell

  16. Mutual information, bit error rate and security in Wójcik's scheme

    E-Print Network [OSTI]

    Zhanjun Zhang

    2004-02-21

    In this paper the correct calculations of the mutual information of the whole transmission, the quantum bit error rate (QBER) are presented. Mistakes of the general conclusions relative to the mutual information, the quantum bit error rate (QBER) and the security in W\\'{o}jcik's paper [Phys. Rev. Lett. {\\bf 90}, 157901(2003)] have been pointed out.

  17. Constant Sustainable Consumption Rate in Optimal Growth with Exhaustible Resources*

    E-Print Network [OSTI]

    Wan, Frederic Yui-Ming

    ;48 Frederic Y. M. Wan resources which are essential to the production of consumption goods. To those concernedConstant Sustainable Consumption Rate in Optimal Growth with Exhaustible Resources* By Frederic Y's criterion of maximum sustainable consumption rate, previously formulated as a minimum

  18. Original article Irrigation, faecal water content and development rate

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Original article Irrigation, faecal water content and development rate of free-living stages- ent faecal water contents (FWC) simulating a submersion (7 or 16 h) or an alternance of spraying, T vitrinus in summer, but higher rates were observed in autumn. The action of water had more effect

  19. T Cell Renewal Rates, Telomerase, and Telomere Length Shortening1

    E-Print Network [OSTI]

    de Boer, Rob J.

    T Cell Renewal Rates, Telomerase, and Telomere Length Shortening1 Rob J. De Boer2 and Andre´ J develop mathematic models describing how the population average of telomere length depends on the cell division rates of naive and memory T cells during clonal expansion and normal renewal. The results show

  20. Palladium-Catalyzed Enantioselective Oxidation of Alcohols: A Dramatic Rate

    E-Print Network [OSTI]

    Stoltz, Brian M.

    Palladium-Catalyzed Enantioselective Oxidation of Alcohols: A Dramatic Rate Acceleration by Cs2CO3 of Cs2CO3 and t-BuOH provides a dramatic rate acceleration in the palladium-catalyzed aerobic oxidative- mercially available palladium complex, sparteine, and mo- lecular oxygen (Scheme 1).1-3 Although our

  1. MATLAB SOFTWARE FOR DETRENDED FLUCTUATION ANALYSIS OF HEART RATE VARIABILITY

    E-Print Network [OSTI]

    Carvalho, João Luiz

    , Heart rate variability, HRV. Abstract: The analysis of heart rate variability (HRV) is an important tool for the assessment of the autonomic regulation of circulatory function. HRV analysis is usually performed using stress tests. This paper presents a Matlab tool for detrended fluctuation analysis (DFA) of HRV signals

  2. Singularity analysis and fracture energy-release rate for composites

    E-Print Network [OSTI]

    Vu-Quoc, Loc

    energy release rate for piecewise homogeneous-anisotropic materials. A new approach of matched asymptoticSingularity analysis and fracture energy-release rate for composites: Piecewise homogeneous-anisotropic materials By Loc Vu-Quoc and Van-Xuan Tran

  3. Joint Optimization of Communication Rates and Linear Systems

    E-Print Network [OSTI]

    Joint Optimization of Communication Rates and Linear Systems L. Xiao M. Johansson H. Hindi S. Boyd system, such as a controller or estimator, in which several signals are transmitted over communication in the design of networked controllers and the associated communication systems, including bit rate limitations

  4. Scalar dissipation rate based flamelet modelling of turbulent premixed flames

    E-Print Network [OSTI]

    Kolla, Hemanth

    2010-03-16

    of species formation rates in the flame zone are required while from the point of view of thermo--acoustics the prediction of spatial variation of heat release rate is crucial; both tasks are challenging but imperative in CFD based design of combustion...

  5. Oil production models with normal rate curves Dudley Stark

    E-Print Network [OSTI]

    Stark, Dudley

    Oil production models with normal rate curves Dudley Stark School of Mathematical Sciences Queen;Abstract The normal curve has been used to fit the rate of both world and U.S.A. oil production. In this paper we give the first theoretical basis for these curve fittings. It is well known that oil field

  6. GTA TRIP GENERATION RATES, 1986 -1996 Eric J. Miller

    E-Print Network [OSTI]

    Toronto, University of

    GTA TRIP GENERATION RATES, 1986 - 1996 by Eric J. Miller Department of Civil Engineering University . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. CHANGES IN GTA TRIP GENERATION RATES, 1986-96 . . . . . . . . . . . . . . . . . . . . . 2 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3. DEMOGRAPHIC FACTORS AFFECTING WORK TRIP GENERATION . . . . . . . . . . 12 3.1 Observed Trends

  7. Hydrogen Peroxide Formation Rates in a PEMFC Anode and Cathode

    E-Print Network [OSTI]

    Sethuraman, Vijay A.

    Hydrogen Peroxide Formation Rates in a PEMFC Anode and Cathode Effect of Humidity and Temperature Hydrogen peroxide H2O2 formation rates in a proton exchange membrane fuel cell PEMFC anode and cathode were, has the capability to be the structural and fundamental unit of an impending hydrogen economy. Two

  8. An observational study of entrainment rate in deep convection

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Guo, Xiaohao; Lu, Chunsong; Zhao, Tianliang; Zhang, Guang Jun; Liu, Yangang

    2015-09-22

    This study estimates entrainment rate and investigates its relationships with cloud properties in 156 deep convective clouds based on in-situ aircraft observations during the TOGA-COARE (Tropical Ocean Global Atmosphere Coupled Ocean Atmosphere Response Experiment) field campaign over the western Pacific. To the authors’ knowledge, this is the first study on the probability density function of entrainment rate, the relationships between entrainment rate and cloud microphysics, and the effects of dry air sources on the calculated entrainment rate in deep convection from an observational perspective. Results show that the probability density function of entrainment rate can be well fitted by lognormal,more »gamma or Weibull distribution, with coefficients of determination being 0.82, 0.85 and 0.80, respectively. Entrainment tends to reduce temperature, water vapor content and moist static energy in cloud due to evaporative cooling and dilution. Inspection of the relationships between entrainment rate and microphysical properties reveals a negative correlation between volume-mean radius and entrainment rate, suggesting the potential dominance of homogeneous mechanism in the clouds examined. The entrainment rate and environmental water vapor content show similar tendencies of variation with the distance of the assumed environmental air to the cloud edges. Their variation tendencies are non-monotonic due to the relatively short distance between adjacent clouds.« less

  9. Compensation Information -Student Rates of Pay Effective May 1, 2013

    E-Print Network [OSTI]

    Saskatchewan, University of

    at 966-2950 or e-mail at hr.inquiries@usask.ca A student assistant is a person enrolled,208.40 (Enrolled in graduate studies) * Monthly rates are calculated as follows: Hourly Rate X 40 hrs per week X 52

  10. Penetration rate prediction for percussive drilling via dry friction model

    E-Print Network [OSTI]

    Krivtsov, Anton M.

    Penetration rate prediction for percussive drilling via dry friction model Anton M. Krivtsov a of percussive drilling assuming a dry friction mechanism to explain the experimentally observed drop in pene in drilling research is a fall of pene- tration rate for higher static loads. This is known both

  11. Cosmic Supernova Rate History and Type Ia Supernova Progenitors

    E-Print Network [OSTI]

    Chiaki Kobayashi; Ken'ichi Nomoto; Takuji Tsujimoto

    2001-02-14

    Adopting a single degenerate scenario for Type Ia supernova progenitors with the metallicity effect, we make a prediction of the cosmic supernova rate history as a composite of the supernova rates in spiral and elliptical galaxies, and compare with the recent observational data up to z ~ 0.55.

  12. High strain rate deformation of NiAl

    SciTech Connect (OSTI)

    Maloy, S.A.; Gray, G.T. III; Darolia, R.

    1994-07-01

    NiAl is a potential high temperature structural material. Applications for which NiAl is being considered (such as rotating components in jet engines) requires knowledge of mechanical properties over a wide range of strain rates. Single crystal NiAl (stoichiometric and Ni 49.75Al 0.25Fe) has been deformed in compression along [100] at strain rates of 0.001, 0.1/s and 2000/s and temperatures of 76,298 and 773K. <111> slip was observed after 76K testing at a strain rate of 0.001/s and 298K testing at a strain rate of 2000/s. Kinking was observed after deformation at 298K and a strain rate of 0.001/s and sometimes at 298 K and a strain rate of 0.1/s. Strain hardening rates of 8200 and 4000 MPa were observed after 773 and 298K testing respectively, at a strain rate of 2000/s. Results are discussed in reference to resulting dislocation substructure.

  13. Temperature-dependence of biomass accumulation rates during secondary succession

    E-Print Network [OSTI]

    Gillooly, Jamie

    on the biochemical kinetics of photosynthesis in chloroplasts. In addition, the rate of biomass accumulation one example of how emergent, ecosystem-level rate processes can be predicted based on the kinetics of uncertainty in terrestrial ecosystem models (e.g. Schimel et al. 2001; Houghton 2003, 2005). Additionally

  14. Rate Analysis of Two Photovoltaic Systems in San Diego

    SciTech Connect (OSTI)

    Doris, E.; Ong, S.; Van Geet, O.

    2009-07-01

    Analysts have found increasing evidence that rate structure has impacts on the economics of solar systems. This paper uses 2007 15-minute interval photovoltaic (PV) system and load data from two San Diego City water treatment facilities to illustrate impacts of different rate designs. The comparison is based on rates available in San Diego at the time of data collection and include proportionately small to large demand charges (relative to volumetric consumption), and varying on- and off- peak times. Findings are twofold for these large commercial systems: 1) transferring costs into demand charges does not result in savings and 2) changes in peak times do not result in a major cost difference during the course of a year. While lessons learned and discussion on rate components are based on the findings, the applicability is limited to buildings with similar systems, environments, rate options, and loads.

  15. Topographic Effects on Ambient Dose Equivalent Rates from Radiocesium Fallout

    E-Print Network [OSTI]

    Malins, Alex; Machida, Masahiko; Saito, Kimiaki

    2015-01-01

    Land topography can affect air radiation dose rates by locating radiation sources closer to, or further, from detector locations when compared to perfectly flat terrain. Hills and slopes can also shield against the propagation of gamma rays. To understand the possible magnitude of topographic effects on air dose rates, this study presents calculations for ambient dose equivalent rates at a range of heights above the ground for varying land topographies. The geometries considered were angled ground at the intersection of two planar surfaces, which is a model for slopes neighboring flat land, and a simple conical geometry, representing settings from hilltops to valley bottoms. In each case the radiation source was radioactive cesium fallout, and the slope angle was varied systematically to determine the effect of topography on the air dose rate. Under the assumption of homogeneous fallout across the land surface, and for these geometries and detector locations, the dose rates at high altitudes are more strongly...

  16. Statistical Methods for Thermonuclear Reaction Rates and Nucleosynthesis Simulations

    E-Print Network [OSTI]

    Iliadis, Christian; Coc, Alain; Timmes, F X; Champagne, Art E

    2014-01-01

    Rigorous statistical methods for estimating thermonuclear reaction rates and nucleosynthesis are becoming increasingly established in nuclear astrophysics. The main challenge being faced is that experimental reaction rates are highly complex quantities derived from a multitude of different measured nuclear parameters (e.g., astrophysical S-factors, resonance energies and strengths, particle and gamma-ray partial widths). We discuss the application of the Monte Carlo method to two distinct, but related, questions. First, given a set of measured nuclear parameters, how can one best estimate the resulting thermonuclear reaction rates and associated uncertainties? Second, given a set of appropriate reaction rates, how can one best estimate the abundances from nucleosynthesis (i.e., reaction network) calculations? The techniques described here provide probability density functions that can be used to derive statistically meaningful reaction rates and final abundances for any desired coverage probability. Examples ...

  17. Spatially resolved heat release rate measurements in turbulent premixed flames

    SciTech Connect (OSTI)

    Ayoola, B.O.; Kaminski, C.F.; Balachandran, R.; Mastorakos, E.; Frank, J.H.

    2006-01-01

    Heat release rate is a fundamental property of great importance for the theoretical and experimental elucidation of unsteady flame behaviors such as combustion noise, combustion instabilities, and pulsed combustion. Investigations of such thermoacoustic interactions require a reliable indicator of heat release rate capable of resolving spatial structures in turbulent flames. Traditionally, heat release rate has been estimated via OH or CH radical chemiluminescence; however, chemiluminescence suffers from being a line-of-sight technique with limited capability for resolving small-scale structures. In this paper, we report spatially resolved two-dimensional measurements of a quantity closely related to heat release rate. The diagnostic technique uses simultaneous OH and CH{sub 2}O planar laser-induced fluorescence (PLIF), and the pixel-by-pixel product of the OH and CH{sub 2}O PLIF signals has previously been shown to correlate well with local heat release rates. Results from this diagnostic technique, which we refer to as heat release rate imaging (HR imaging), are compared with traditional OH chemiluminescence measurements in several flames. Studies were performed in lean premixed ethylene flames stabilized between opposed jets and with a bluff body. Correlations between bulk strain rates and local heat release rates were obtained and the effects of curvature on heat release rate were investigated. The results show that the heat release rate tends to increase with increasing negative curvature for the flames investigated for which Lewis numbers are greater than unity. This correlation becomes more pronounced as the flame gets closer to global extinction.

  18. Multi-UAV Network Control through Dynamic Task Allocation: Ensuring Data-Rate and Bit-Error-Rate Support

    E-Print Network [OSTI]

    Multi-UAV Network Control through Dynamic Task Allocation: Ensuring Data-Rate and Bit-Error-Rate Support Andrew Kopeikin, Sameera S. Ponda, Luke B. Johnson, and Jonathan P. How Abstract-- A multi-UAV distributed task allocation to engage under-utilized UAVs to serve as communication relays and to ensure

  19. Journals Distributed by the University of Chicago Press 2012 Subscription Rates --All rates are for print copies unless otherwise noted--

    E-Print Network [OSTI]

    Mateo, Jill M.

    Journals Distributed by the University of Chicago Press 2012 Subscription Rates --All rates are for print copies unless otherwise noted-- For Northwestern University Press Journal Title ISSN Volume Freq-only) $125 (e-only) Online-only title Inagural issue OA, all future issues restricted access. Journal

  20. Understanding the role of multi-rate retry mechanism for effective rate control in 802.11 wireless LANs 

    E-Print Network [OSTI]

    Marina, Mahesh; Koci, Neda

    We consider the multi-rate retry (MRR) capability provided by current 802.11 implementations and carry out simulation-based study of its impact on performance with state-of- the-art rate control mechanisms in typical indoor wireless LAN scenarios...

  1. Error Rate Comparison during Polymerase Chain Reaction by DNA Polymerase

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    McInerney, Peter; Adams, Paul; Hadi, Masood Z.

    2014-01-01

    As larger-scale cloning projects become more prevalent, there is an increasing need for comparisons among high fidelity DNA polymerases used for PCR amplification. All polymerases marketed for PCR applications are tested for fidelity properties (i.e., error rate determination) by vendors, and numerous literature reports have addressed PCR enzyme fidelity. Nonetheless, it is often difficult to make direct comparisons among different enzymes due to numerous methodological and analytical differences from study to study. We have measured the error rates for 6 DNA polymerases commonly used in PCR applications, including 3 polymerases typically used for cloning applications requiring high fidelity. Errormore »rate measurement values reported here were obtained by direct sequencing of cloned PCR products. The strategy employed here allows interrogation of error rate across a very large DNA sequence space, since 94 unique DNA targets were used as templates for PCR cloning. The six enzymes included in the study, Taq polymerase, AccuPrime-Taq High Fidelity, KOD Hot Start, cloned Pfu polymerase, Phusion Hot Start, and Pwo polymerase, we find the lowest error rates with Pfu , Phusion, and Pwo polymerases. Error rates are comparable for these 3 enzymes and are >10x lower than the error rate observed with Taq polymerase. Mutation spectra are reported, with the 3 high fidelity enzymes displaying broadly similar types of mutations. For these enzymes, transition mutations predominate, with little bias observed for type of transition. « less

  2. Characterization of evolutionary rates and constraints in three mammalian genomes

    SciTech Connect (OSTI)

    Cooper, Gregory M.; Brudno, Michael; Stone, Eric A.; Dubchak, Inna; Batzoglou, Serafim; Sidow, Arend

    2004-02-15

    We present an analysis of rates and patterns of microevolutionary phenomena that have shaped the human, mouse, and rat genomes since their last common ancestor. We find evidence for a shift in the mutational spectrum between the mouse and rat lineages, with the net effect being a relative increase in GC content in the rat genome. Our estimate for the neutral point substitution rate separating the two rodents is 0.196 substitutions per site, and 0.65 substitutions per site for the tree relating all three mammals. Small insertions and deletions of 1-10 bp in length (''microindels'') occur at approximately 5 percent of the point substitution rate. Inferred regional correlations in evolutionary rates between lineages and between types of sites support the idea that rates of evolution are influenced by local genomic or cell biological context. No substantial correlations between rates of point substitutions and rates of microindels are found, however, implying that the influences that affect these processes are distinct. Finally, we have identified those regions in the human genome that are evolving slowly, which are likely to include functional elements important to human biology. At least 5 percent of the human genome is under substantial constraint, most of which is noncoding.

  3. Properties of water surface discharge at different pulse repetition rates

    SciTech Connect (OSTI)

    Ruma,; Yoshihara, K. [Graduate School of Science and Technology, Kumamoto University, Kumamoto 860-8555 (Japan); Hosseini, S. H. R., E-mail: hosseini@kumamoto-u.ac.jp; Sakugawa, T.; Akiyama, H. [Graduate School of Science and Technology, Kumamoto University, Kumamoto 860-8555 (Japan); Institute of Pulsed Power Science, Kumamoto University, Kumamoto 860-8555 (Japan); Akiyama, M. [Department of Electrical and Electronic Engineering, Kagoshima University, Kagoshima 890-0065 (Japan); Lukeš, P. [Institute of Plasma Physics, AS CR, Prague, Prague 18200 (Czech Republic)

    2014-09-28

    The properties of water surface discharge plasma for variety of pulse repetition rates are investigated. A magnetic pulse compression (MPC) pulsed power modulator able to deliver pulse repetition rates up to 1000 Hz, with 0.5 J per pulse energy output at 25 kV, was used as the pulsed power source. Positive pulse with a point-to-plane electrode configuration was used for the experiments. The concentration and production yield of hydrogen peroxide (H?O?) were quantitatively measured and orange II organic dye was treated, to evaluate the chemical properties of the discharge reactor. Experimental results show that the physical and chemical properties of water surface discharge are not influenced by pulse repetition rate, very different from those observed for under water discharge. The production yield of H?O? and degradation rate per pulse of the dye did not significantly vary at different pulse repetition rates under a constant discharge mode on water surface. In addition, the solution temperature, pH, and conductivity for both water surface and underwater discharge reactors were measured to compare their plasma properties for different pulse repetition rates. The results confirm that surface discharge can be employed at high pulse repetition rates as a reliable and advantageous method for industrial and environmental decontamination applications.

  4. Standby Rates for Combined Heat and Power Systems

    SciTech Connect (OSTI)

    Sedano, Richard; Selecky, James; Iverson, Kathryn; Al-Jabir, Ali

    2014-02-01

    Improvements in technology, low natural gas prices, and more flexible and positive attitudes in government and utilities are making distributed generation more viable. With more distributed generation, notably combined heat and power, comes an increase in the importance of standby rates, the cost of services utilities provide when customer generation is not operating or is insufficient to meet full load. This work looks at existing utility standby tariffs in five states. It uses these existing rates and terms to showcase practices that demonstrate a sound application of regulatory principles and ones that do not. The paper also addresses areas for improvement in standby rates.

  5. Evaluation of Instrumentation and Dynamic Thermal Ratings for Overhead Lines

    SciTech Connect (OSTI)

    Phillips, A.

    2013-01-31

    In 2010, a project was initiated through a partnership between the Department of Energy (DOE) and the New York Power Authority (NYPA) to evaluate EPRI?s rating technology and instrumentation that can be used to monitor the thermal states of transmission lines and provide the required real-time data for real-time rating calculations. The project included the installation and maintenance of various instruments at three 230 kV line sites in northern New York. The instruments were monitored, and data collection and rating calculations were performed for about a three year period.

  6. Review of Mathematical Techniques Applicable in Astrophysical Reaction Rate Theory

    E-Print Network [OSTI]

    A. M. Mathai; H. J. Haubold

    2002-06-23

    An overview is presented on statistical techniques for the analytic evaluation of integrals for non-resonant, non-resonant depleted, non-resonant cut-off, non-resonant sccreened, and resonant thermonuclear reaction rates. The techniques are based on statistical distribution theory and the theory of Meijer's G-function and Fox's H-function. The implementation of Meijer's G-function in Mathematica constituts an additional utility for analytic manipulations and numerical computation of thermonuclear reaction rate integrals. Recent results in the astrophysical literature related to the use of analytic thermonuclear reaction rates are incorporated.

  7. Solidification at the High and Low Rate Extreme

    SciTech Connect (OSTI)

    Halim Meco

    2004-12-19

    The microstructures formed upon solidification are strongly influenced by the imposed growth rates on an alloy system. Depending on the characteristics of the solidification process, a wide range of growth rates is accessible. The prevailing solidification mechanisms, and thus the final microstructure of the alloy, are governed by these imposed growth rates. At the high rate extreme, for instance, one can have access to novel microstructures that are unattainable at low growth rates. While the low growth rates can be utilized for the study of the intrinsic growth behavior of a certain phase growing from the melt. Although the length scales associated with certain processes, such as capillarity, and the diffusion of heat and solute, are different at low and high rate extremes, the phenomena that govern the selection of a certain microstructural length scale or a growth mode are the same. Consequently, one can analyze the solidification phenomena at both high and low rates by using the same governing principles. In this study, we examined the microstructural control at both low and high extremes. For the high rate extreme, the formation of crystalline products and factors that control the microstructure during rapid solidification by free-jet melt spinning are examined in Fe-Si-B system. Particular attention was given to the behavior of the melt pool at different quench-wheel speeds. Since the solidification process takes place within the melt-pool that forms on the rotating quench-wheel, we examined the influence of melt-pool dynamics on nucleation and growth of crystalline solidification products and glass formation. High-speed imaging of the melt-pool, analysis of ribbon microstructure, and measurement of ribbon geometry and surface character all indicate upper and lower limits for melt-spinning rates for which nucleation can be avoided, and fully amorphous ribbons can be achieved. Comparison of the relevant time scales reveals that surface-controlled melt-pool oscillation may be the dominant factor governing the onset of unsteady thermal conditions accompanied by varying amounts of crystalline nucleation observed near the lower limit. At high quench-wheel velocities, the influence of these oscillations is minimal due to very short melt-pool residence times. However, microstructural evidence suggests that the entrapment of gas pockets at the wheel-metal interface plays a critical role in establishing the upper rate limit. An observed transition in wheel-side surface character with increasing melt-spinning rate supports this conclusion.

  8. Cost Bases for Incentive Rates Applicable to Industrial Loads 

    E-Print Network [OSTI]

    Stover, C. N.

    1987-01-01

    ; they involve a depressed economy base in all or certain segments of the service area, a decrease in load, excess generation capacity, and an increase in base rates. An increase in rates may also be related to the commercial operation of a base load unit, i... utility has completely abandoned a pricing structure that is in any way related to cost. Some of the incentive rates are very short lived and reflect transient economic conditions while others tend to reflect long-term economic relationships...

  9. Estimation of the Mass Outflow Rate From Compact Objects

    E-Print Network [OSTI]

    Sandip K. Chakrabarti

    1998-12-02

    Outflows are common in many astrophysical systems which contain black holes and neutron stars. Difference between stellar outflows and outflows from these systems is that the outflows in these systems have to form out of the inflowing material only. The inflowing material can form a hot and dense cloud surrounding the compact object either because of centrifugal barrier or a denser barrier due to pair plasma or pre-heating effects. This barrier behaves like a stellar surface as far as the mass loss is concerned. We estimate the outflow rate from such considerations. These estimated rates roughly match with the rates in real observations as well as those obtained from numerical experiments.

  10. Neutron capture rates and r-process nucleosynthesis

    E-Print Network [OSTI]

    R. Surman; M. Mumpower; G. C. McLaughlin; R. Sinclair; W. R. Hix; K. L. Jones

    2013-08-31

    Simulations of r-process nucleosynthesis require nuclear physics information for thousands of neutron-rich nuclear species from the line of stability to the neutron drip line. While arguably the most important pieces of nuclear data for the r-process are the masses and beta decay rates, individual neutron capture rates can also be of key importance in setting the final r-process abundance pattern. Here we consider the influence of neutron capture rates in forming the A~80 and rare earth peaks.

  11. The impact of retail rate structures on the economics of commercial photovoltaic systems in California

    E-Print Network [OSTI]

    Mills, Andrew D.

    2009-01-01

    the impact of retail electricity rate design on the economiccustomer retail electricity rates currently offered in thethe design of retail electricity rates, particularly for

  12. The Impact of Retail Rate Structures on the Economics of Commercial Photovoltaic Systems in California

    E-Print Network [OSTI]

    Mills, Andrew

    2009-01-01

    the impact of retail electricity rate design on the economiccustomer retail electricity rates currently offered in thethe design of retail electricity rates, particularly for

  13. The Impact of Retail Rate Structures on the Economics of Commercial Photovoltaic Systems in California

    E-Print Network [OSTI]

    Wiser, Ryan; Mills, Andrew; Barbose, Galen; Golove, William

    2007-01-01

    competitive with retail electricity rates. In this report,the design of retail electricity rates, particularly forand industrial electricity rates currently offered by the

  14. Fairness and stability of end-to-end congestion Frank Kelly

    E-Print Network [OSTI]

    Kelly, Frank

    Sciences, University of Cambridge, Wilberforce Road, Cam- bridge CB3 0WB UK. Email: f with the earlier telephony infrastructure where a smart network connects endpoints (telephones) that have little

  15. A Study of Fixed-Length Subset Recombination Kelly D. Crawford

    E-Print Network [OSTI]

    Wainwright, Roger L.

    @amoco.com Cory J. Hoelting The University of Tulsa hoeltc@euler.mcs.utulsa.edu Roger L. Wainwright The University of Tulsa rogerw@penguin.mcs.utulsa.edu Dale A. Schoenefeld The University of Tulsa schoend

  16. Residents lead the way in restoring the River Wandle by Kelly Oakes

    E-Print Network [OSTI]

    the Wandle was a famous trout fishery ­ rumour has it Lord Nelson fished there ­ but industry that sprung up it hard for fish to make their home there. Pollution in the 1930s killed off what was left of the trout a nearby sewage works was accidentally emptied into it, killing two tonnes of fish. "At that time a lot

  17. System-level Prototyping with HyperTransport Watson, Myles and Flanagan, Kelly

    E-Print Network [OSTI]

    Gertz, Michael

    the pressure on, and the importance of, the memory and I/O subsystems [3]. The increase in importance of memory, and are marketed as flexible application accelerators. They provide low-latency and low- power computational resources for applications such as bioinformatics, data-mining, real-time financial analysis, and oil

  18. Safety Cases for Software Application Reuse P Fenelon, T P Kelly, J A McDermid

    E-Print Network [OSTI]

    Kelly, Tim

    on an analysis of a reactor protection system. 1 Introduction There is a long-established principle. These principles have been applied retrospectively to the safety case for a reactor protection system (the Stage 9. These principles have been adopted in developing safety-critical software, but often only through the reuse of low

  19. Energy: Converting from acoustic to biological resource units Kelly J. Benoit-Birda)

    E-Print Network [OSTI]

    Benoit-Bird, Kelly J.

    for secondary production, carbon, ATP, and energy content calories . In every case, biomass is a measure of organic resources or available energy. Acousti- cians and fisheries biologists attempt to assess biomass to assess biomass through a direct conversion of acoustic energy to units of organic energy without

  20. PRODUCTION PLANNING FOR WATER SUPPLY NETWORKS Michael Hofmeister, Sean Ahmad Colbert-Kelly

    E-Print Network [OSTI]

    : 612-626-7370 URL: http://www.ima.umn.edu #12;Mathematical Modeling in Industry XIV CIMAT ­ IMA ­ PIMS the network, and the number of pump switches. The original water flow model was projected into a mathematical as an LP problem. We then considered discrete pumps and added the minimized discrete pumps via both

  1. Kelly C. Lee, Pharm.D., MAS, BCPP Why do a residency?

    E-Print Network [OSTI]

    Gleeson, Joseph G.

    /work? Can I afford to live away from home? What are the benefits? Number of residents in the program or focus on preparing for specialty residencies or fellowships 5 #12;Reality Check Where do I want to live Are there support systems? Will I miss the sunny weather in San Diego? 6 #12;Benefits of Residency Training Gets

  2. Smarter Electricity through Argumentation Menelaos Makriyiannis, Tudor Lung, Robert Craven, Francesca Toni and Jack Kelly

    E-Print Network [OSTI]

    Toni, Francesca

    Smarter Electricity through Argumentation Menelaos Makriyiannis, Tudor Lung, Robert Craven101,ft,dk3810}@doc.ic.ac.uk, tudor.lung@gmail.com Abstract--The current, widespread introduction

  3. Delay-Centric Handover in SCTP Andrew Kelly, B.Eng

    E-Print Network [OSTI]

    Murphy, John

    at the transport layer and is transparent to the end user, something that is still important in non an individual SCTP association in order to determine the round trip delay to each of these addresses

  4. The impact of lead time on truckload transportation rates

    E-Print Network [OSTI]

    Caldwell, Erik R. (Erik Russell)

    2008-01-01

    The objective of this thesis was to analyze truckload shipment transactions in order to determine if rates are impacted by tender lead time, which is the amount of time between when a carrier is offered a load to when the ...

  5. Inclusive Rates and Spectra of the Lambda, Cascade, and Omega...

    Office of Scientific and Technical Information (OSTI)

    Lambda as 0.0900 +- 0.0006(stat.) +- 0.0039(sys.) per hadronic event. Our measured production rate at the same energy for the cascade hyperon is 0.00562 +- 0.00013(stat.)...

  6. Jet Rates in Deep Inelastic Scattering at Small $x$

    E-Print Network [OSTI]

    B. R. Webber

    1998-10-08

    The recent results of Forshaw and Sabio Vera on small-$x$ jet rates to order $\\alpha_s^3$ are extended to all orders, for any number of jets. A simple generating function is obtained.

  7. Constant displacement rate experiments and constitutive modeling of asphalt mixtures 

    E-Print Network [OSTI]

    Hariharakumar, Pradeep

    2006-04-12

    The focus of this dissertation is on constant displacment rate experiments on asphalt concrete and on developing continuum models in a general thermo-mechanical setting which will corroborate with the experimental results. Modeling asphalt concrete...

  8. Probing Ultrafast Solvation Dynamics with High Repetition-Rate...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    systems. Thanks to implementation of a high-repetition-rate (54 kHz-6.5 MHz), high-power (>10 W) laser system at the X-ray Science Division 7-ID-D beamline at the Advanced...

  9. HEADLINE: BPA RAISES RATES TO BOLSTER FEDERAL POWER AND TRANSMISSION...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Doug Johnson, 503-230-5840 or 503-230-5131 BPA adopts new wholesale power and transmission rates Increases needed to sustain system value Portland, Ore. - The Bonneville...

  10. Statistical testing and estimation in continuous time interest rate models 

    E-Print Network [OSTI]

    Kim, Myung Suk

    2006-10-30

    The shape of drift function in continuous time interest rate models has been investigated by many authors during the past decade. The main concerns have been whether the drift function is linear or nonlinear, but no convincing conclusions have been...

  11. Migrant Remittances and Exchange Rate Regimes in the Developing World

    E-Print Network [OSTI]

    Singer, David Andrew

    This article argues that the international financial consequences of immigration exert a substantial influence on the choice of exchange rate regimes in the developing world. Over the past two decades, migrant remittances ...

  12. Studies of the CMS tracker at high trigger rate

    E-Print Network [OSTI]

    Chan, M.

    During the latter months of 2006 and the first half of 2007, the CMS Tracker was assembled and operated at the Tracker Integration Facility at CERN. During this period the performance of the tracker at trigger rates up to ...

  13. Duke Energy (Electric)- Energy Star Homes Rate Discount Program

    Broader source: Energy.gov [DOE]

    Duke Energy encourages residential customers to buy energy-efficient homes through the utility's Energy Star Homes Program, which awards a rate discount to customers living in Energy Star homes. To...

  14. Duke Energy (Electric)- Energy Star Homes Rate Discount Program

    Broader source: Energy.gov [DOE]

    Duke Energy encourages residential customers to buy energy-efficient homes through the utility's Energy Star Homes Program, which awards a rate discount to customers living in Energy Star homes....

  15. Construction, Qualification, and Low Rate Production Start-up...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of a DC Bus Capacitor High Volume Manufacturing Facility with Capacity to Support 100,000 Electric Drive Vehicles Construction, Qualification, and Low Rate Production Start-up of a...

  16. Characteristics of spot-market rate indexes for truckload transportation

    E-Print Network [OSTI]

    Bignell, Andrew (Andrew Souglas)

    2013-01-01

    In the truckload transportation industry in the United States, a number of indexes are published that attempt to measure changes in rates, but no single index has emerged as an industry standard. Industry participants, ...

  17. The Potential Benefits of Distributed Generation and the Rate...

    Broader source: Energy.gov (indexed) [DOE]

    The Potential Benefits of Distributed Generation and the Rate-Related Issues That May Impede Its Expansion. Report Pursuant to Section 1817 of the Energy Policy Act of 2005. The...

  18. Effect of Alumina Source on the Rate of Melting Demonstrated...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Effect of Alumina Source on the Rate of Melting Demonstrated with Nuclear Waste Glass Batch Citation Details In-Document Search Title: Effect of Alumina Source on...

  19. Comparison of two different rating programs for sustainable homes

    E-Print Network [OSTI]

    Bjarnadottir, Margret Halla

    2009-01-01

    This thesis compares two different rating programs for sustainable homes; The Code for Sustainable Homes in the United Kingdom, and LEED for Homes in the United States. The comparison is both in general and with respect ...

  20. Optimization of time-based rates in forward energy markets

    E-Print Network [OSTI]

    Wang, J.

    This paper presents a new two-step design approach of Time-Based Rate (TBR) programs for markets with a high penetration of variable energy sources such as wind power. First, an optimal market time horizon must be determined ...