Powered by Deep Web Technologies
Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Carbon dioxide injection and resultant alteration of Weber Sandstone (Pennsylvanian-Permian), Rangely field, Colorado  

SciTech Connect

Geologic interpretations made during the current EOR (enhanced oil recovery) project at Rangely field (Rio Blanco County, Colorado), have made interesting connections between alteration of reservoir mineralogy and texture, changes in produced water composition, and increased production problems. Carbon dioxide is being injected into the Weber Sandstone in portions of Rangely field. The carbon dioxide injection is part of a very successful tertiary recovery project initiated in late 1986. The bottomhole pH of Weber brine has decreased from approximately 7.5 to 4.5 with the addition of CO/sub 2/. Changes in the chemistry of produced water are associated with alteration of reservoir mineralogy. The CO/sub 2/ flood has caused a substantial increase in the concentrations of iron, calcium, magnesium, and strontium in the produced brine. The amount of increase is directly related to the volume of CO/sub 2/ produced in each well. This increase resulted from the dissolution of carbonate cements, authigenic clays, and detrital feldspars. An increase in the calculated scaling potential of the produced water is a result of this change in chemistry. Hypotheses based on the water-chemistry changes were confirmed in pressure-cell and core-flood experiments. Core-flood experiments also indicate no net change in permeability following carbon dioxide injection: the increase in permeability due to the dissolution of carbonate cements is being offset by a decrease caused by migratory clays plugging pore throats. The clays, which coat the authigenic carbonates, are liberated when the carbonates are dissolved.

Bowker, K.A.; Shuler, P.J.

1989-03-01T23:59:59.000Z

2

Adam Weber  

NLE Websites -- All DOE Office Websites (Extended Search)

investigation and mathematical modeling of water management in polymer-electrolyte fuel cells. Dr. Weber continued his study of water and thermal management in...

3

Adam Weber  

NLE Websites -- All DOE Office Websites (Extended Search)

Adam Weber Adam Weber Adam Weber Electrochemical Technologies Group Lawrence Berkeley National Laboratory 1 Cyclotron Road MS 70-108B Berkeley CA 94720 Office Location: 70-0112 (510) 486-6308 AZWeber@lbl.gov Adam Z. Weber holds B.S. and M.S. degrees from Tufts University, the latter under the guidance of Professor Maria Flytzani-Stephanopoulos. Next, he earned his Ph.D. at University of California, Berkeley in chemical engineering under the guidance of John Newman. His dissertation work focused on the fundamental investigation and mathematical modeling of water management in polymer-electrolyte fuel cells. Dr. Weber continued his study of water and thermal management in polymer-electrolyte fuel cells at Lawrence Berkeley National Laboratory, where he is now a staff scientist.

4

Renewable Energy Opportunities at White Sands Missile Range, New Mexico  

DOE Green Energy (OSTI)

The document provides an overview of renewable resource potential at White Sands Missile Range (WSMR) based primarily upon analysis of secondary data sources supplemented with limited on-site evaluations. The effort was funded by the U.S. Army Installation Management Command (IMCOM) as follow-on to the 2005 DoD Renewable Energy Assessment. This effort focuses on grid-connected generation of electricity from renewable energy sources and also ground source heat pumps (GSHPs) for heating and cooling buildings, as directed by IMCOM.

Chvala, William D.; Solana, Amy E.; States, Jennifer C.; Warwick, William M.; Weimar, Mark R.; Dixon, Douglas R.

2008-09-01T23:59:59.000Z

5

Gunther H. Weber  

NLE Websites -- All DOE Office Websites (Extended Search)

Oliver R ubel, Hank Childs, Gunther H. Weber, Prabhat, Kesheng Wu, "A System for Query Based Analysis and Visualization", Third International EuroVis Workshop on Visual...

6

Groundwater flow near the Shoal Site, Sand Springs Range, Nevada: Impact of density-driven flow  

Science Conference Proceedings (OSTI)

The nature of flow from a highland recharge area in a mountain range in north-central Nevada to discharge areas on either side of the range is evaluated to refine a conceptual model of contaminant transport from an underground nuclear test conducted beneath the range. The test, known as the Shoal event, was conducted in 1963 in granitic rocks of the Sand Springs Range. Sparse hydraulic head measurements from the early 1960s suggest flow from the shot location to the east to Fairview Valley, while hydrochemistry supports flow to salt pans in Fourmile Flat to the west. Chemical and isotopic data collected from water samples and during well-logging arc best explained by a reflux brine system on the west side of the Sand Springs Range, rather than a typical local flow system where all flow occurs from recharge areas in the highlands to a central discharge area in a playa. Instead, dense saline water from the playa is apparently being driven toward the range by density contrasts. The data collected between the range and Fourmile Flat suggest the groundwater is a mixture of younger, fresher recharge water with older brine. Chemical contrasts between groundwater in the east and west valleys reflect the absence of re-flux water in Fairview Valley because the regional discharge area is distant and thus there is no accumulation of salts. The refluxing hydraulic system probably developed after the end of the last pluvial period and differences between the location of the groundwater divide based on hydraulic and chemical indicators could reflect movement of the divide as the groundwater system adjusts to the new reflux condition.

Chapman, J.; Mihevc, T.; McKay, A.

1994-09-01T23:59:59.000Z

7

Extensional wave attenuation and velocity in partially-saturated sand in the sonic frequency range  

E-Print Network (OSTI)

sands can be viewed as an end-member of the spectrum of naturally-occurring granular materials, with tight

Liu, Z.; Rector, J.W.; Nihei, K.T.; Tomutsa, L.; Myer, L.R.; Nakagawa, S.

2002-01-01T23:59:59.000Z

8

Extensional wave attenuation and velocity in partially saturated sand in the sonic frequency range  

E-Print Network (OSTI)

sands can be viewed as an end-member of the spectrum of naturally-occurring granular materials, with tight

Liu, Z.; Rector, J.W.; Nihei, K.T.; Tomutsa, L.; Myer, L.R.; Nakagawa, S.

2001-01-01T23:59:59.000Z

9

Potential for substitution of geothermal energy at domestic defense installations and White Sands Missile Range  

DOE Green Energy (OSTI)

Geothermal resources that might provide substitute energy at any of 76 defense installations are identified and evaluated. The geologic characteristics and related economics of potential geothermal resources located at or near the 76 installations were estimated. The geologic assessment identified 18 installations with possible geothermal resources and 4 Atlantic Coastal Plain resource configurations that represented the alternatives available to East Coast bases. These 18 locations and 4 resource configurations, together with 2 possible resources at the White Sands Missile Range and a potential resource at Kings Bay, Georgia, were examined to determine the relative economics of substituting potential geothermal energy for part or all of the existing oil, gas, and electrical energy usage. Four of the military installations - Mountain Home, Norton, Hawthorne, and Sierra - appear to be co-located with possible geothermal resources which, if present, might provide substitute energy at or below current market prices for oil. Six additional locations - Ellsworth, Luke, Williams, Bliss, Fallon, and Twentynine Palms - could become economically attractive under certain conditions. No geothermal resource was found to be economically competitive with natural gas at current controlled prices. Generation of electric power at the locations studied is estimated to be uneconomic at present.

Bakewell, C.A.; Renner, J.L.

1982-01-01T23:59:59.000Z

10

Variations of Winds and Turbulence Seen by the 50-MHz Radar at White Sands Missile Range, New Mexico  

Science Conference Proceedings (OSTI)

The mean vertical profiles of the winds from about 5 to 20 km at White Sands Missile Range, New Mexico, are described. The variability of wind speed, spectral width, volume reflectivity calibrated as CN2, and vertical wind shear are documented as ...

G. D. Nastrom; F. D. Eaton

1995-10-01T23:59:59.000Z

11

Low Dose Radiation Research Program: Thomas Weber  

NLE Websites -- All DOE Office Websites (Extended Search)

2005 Workshop: A Paracrine Signal Mediates The Cell Transformation Response To Low Dose Gamma Radiation in JB6 Cells. Weber, T.J., Siegel, R.W., Markillie, L.M., Chrisler,...

12

The Operational Mesogamma-Scale Analysis and Forecast System of the U.S. Army Test and Evaluation Command. Part IV: The White Sands Missile Range Auto-Nowcast System  

Science Conference Proceedings (OSTI)

During the summer months at the U.S. Army Test and Evaluation Command’s (ATEC) White Sands Missile Range (WSMR), forecasting thunderstorm activity is one of the primary duties of the range forecasters. The safety of personnel working on the range ...

Thomas R. Saxen; Cynthia K. Mueller; Thomas T. Warner; Matthias Steiner; Edward E. Ellison; Eric W. Hatfield; Terri L. Betancourt; Susan M. Dettling; Niles A. Oien

2008-04-01T23:59:59.000Z

13

Row-Action Inversion of the Barrick–Weber Equations  

Science Conference Proceedings (OSTI)

The Barrick–Weber equations describe the interaction of radar signals with the dynamic ocean surface, and so provide a mathematical basis for oceanic remote sensing. This report considers the inversion of these equations with several of the row-...

J. J. Green; L. R. Wyatt

2006-03-01T23:59:59.000Z

14

LARES/WEBER-SAT, frame-dragging and fundamental physics  

E-Print Network (OSTI)

After a brief introduction on the scientific objectives of the LARES/WEBER-SAT satellite we present the recent measurement of the Lense-Thirring effect using the nodes of the LAGEOS and LAGEOS 2 satellites and using the Earth gravity model EIGENGRACE02S obtained by the GRACE space mission, we also include some determination of the rate of change of the lowest order Earth's even zonal harmonics. Finally, we describe an interesting possibility of testing the Brane-World unified theory of fundamental interactions by the use of a specially designed LARES/WEBER-SAT satellite.

Ignazio Ciufolini

2004-12-01T23:59:59.000Z

15

Silica Sand  

NLE Websites -- All DOE Office Websites (Extended Search)

the molds and cores in foundries that make steel castings, and for casting gray iron, brass, aluminum and magnesium metals. Since silica sand has a very high melting point, it is...

16

10 Questions for a Scientist: Dr. Adam Weber of Lawrence Berkeley National  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

10 Questions for a Scientist: Dr. Adam Weber of Lawrence Berkeley 10 Questions for a Scientist: Dr. Adam Weber of Lawrence Berkeley National Laboratory 10 Questions for a Scientist: Dr. Adam Weber of Lawrence Berkeley National Laboratory January 15, 2014 - 10:25am Addthis Dr. Adam Weber oversees the work of intern Sara Kelly at Lawrence Berkeley National Laboratory in California. Dr. Weber was recently named one of the winners of the Presidential Early Career Awards for Scientists and Engineers. | Photo by Roy Kaltschmidt, Lawrence Berkeley National Laboratory Dr. Adam Weber oversees the work of intern Sara Kelly at Lawrence Berkeley National Laboratory in California. Dr. Weber was recently named one of the winners of the Presidential Early Career Awards for Scientists and Engineers. | Photo by Roy Kaltschmidt, Lawrence Berkeley National

17

10 Questions for a Scientist: Dr. Adam Weber of Lawrence Berkeley National  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

10 Questions for a Scientist: Dr. Adam Weber of Lawrence Berkeley 10 Questions for a Scientist: Dr. Adam Weber of Lawrence Berkeley National Laboratory 10 Questions for a Scientist: Dr. Adam Weber of Lawrence Berkeley National Laboratory January 15, 2014 - 10:25am Addthis Dr. Adam Weber oversees the work of intern Sara Kelly at Lawrence Berkeley National Laboratory in California. Dr. Weber was recently named one of the winners of the Presidential Early Career Awards for Scientists and Engineers. | Photo by Roy Kaltschmidt, Lawrence Berkeley National Laboratory Dr. Adam Weber oversees the work of intern Sara Kelly at Lawrence Berkeley National Laboratory in California. Dr. Weber was recently named one of the winners of the Presidential Early Career Awards for Scientists and Engineers. | Photo by Roy Kaltschmidt, Lawrence Berkeley National

18

Weber County, Utah: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Weber County, Utah: Energy Resources Weber County, Utah: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 41.2602635°, -111.9522491° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.2602635,"lon":-111.9522491,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

19

FIA-13-0073 - In the Matter of Gabriele Weber | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 - In the Matter of Gabriele Weber 3 - In the Matter of Gabriele Weber FIA-13-0073 - In the Matter of Gabriele Weber On December 3, 2013, the Office of Hearings and Appeals (OHA) issued a decision denying an appeal (Appeal) from a Freedom of Information Act (FOIA) determination issued by the Department of Energy's National Nuclear Security Administration (NNSA). The Appellant contested the adequacy of the search for documents responsive to its FOIA request. The OHA reviewed NNSA's description of its search. NNSA described the searches that were conducted at the Lawrence Livermore National Laboratory and the Nevada Site Office, and thus, OHA determined that NNSA conducted an adequate search for responsive documents. Therefore, the OHA denied the Appeal. FIA-13-0073.pdf More Documents & Publications

20

Observations of Thermally Driven Wind Jets at the Exit of Weber Canyon, Utah  

Science Conference Proceedings (OSTI)

Thermally driven valley-exit jets were investigated at Utah’s Weber Canyon, a main tributary of the Great Salt Lake basin. An intensive measurement campaign during July–September 2010 supplemented longer-term measurements to characterize the wind ...

Morgan F. Chrust; C. David Whiteman; Sebastian W. Hoch

2013-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Team Sand Point (SP)  

E-Print Network (OSTI)

The purpose of this flight report is to summarize the field activities of the ShoreZone aerial video imaging (AVI) survey conducted out of Sand Point and Cold Bay in

Team Cold Bay (cb

2011-01-01T23:59:59.000Z

22

Tar Sands | Open Energy Information  

Open Energy Info (EERE)

Tar Sands Tar Sands Jump to: navigation, search More info on OpenEI Oil and Gas Gateway Federal Environmental Statues Federal Oil and Gas Statutes Oil and Gas Companies United States Oil and Gas Boards International Oil and Gas Boards Related Reports Keystone Pipeline System Canada's Oil Sands Royal Society of Canada: Environmental and Health Impacts of Canada's Oil Sands Industry Dictionary.png Tar Sands: A resource, found in particular abundance in Canada, where viscous petroleum is mixed in with a layer of sand, clay, and water. The form of petroleum is often referred to as "bitumen". The resource has only recently been considered part of the world's oil reserves Other definitions:Wikipedia Reegle Tarsands1.png About Tar Sands The Tar Sands, also referred to as Oil Sands, or Bitumen Sands, are a

23

Sand consolidation methods  

SciTech Connect

This patent describes a method for consolidating unconsolidated mineral particles including sand in a subterranean petroleum formation penetrated by a well in fluid communication with at least a portion of the formation. It comprises: providing a sand consolidating fluid comprising a polymerizable monomer, diluent for the monomer, and a nonvolatile strong acid catalyst capable of causing polymerization of the monomer at fluid injection temperatures; mixing the sand consolidating fluid with steam to form a multiphase treating fluid; injecting the treating fluid into the formation to occupy the void space of at least a portion of the formation adjacent to the well; and allowing the injected fluids to remain in the formations for a period of time sufficient to accomplish at least partial polymerization of the monomer, forming a permeable consolidated mass around the wellbore. Also described is a method for forming a fluid impermeable zone in a permeable, subterranean oil-containing formation adjacent to a wellbore penetrating the formation.

Friedman, R.H.; Surles, B.W.; Fader, P.D.

1990-02-27T23:59:59.000Z

24

Method and apparatus for hydrocarbon recovery from tar sands  

DOE Patents (OSTI)

A method and apparatus for utilizing tar sands having a broad range of bitumen content is disclosed. More particularly, tar sands are pyrolyzed in a cyclone retort with high temperature gases recycled from the cyclone retort to produce oil and hydrocarbon products. The spent tar sands are then burned at 2000.degree. F. in a burner to remove residual char and produce a solid waste that is easily disposable. The process and apparatus have the advantages of being able to utilize tar sands having a broad range of bitumen content and the advantage of producing product gases that are free from combustion gases and thereby have a higher heating value. Another important advantage is rapid pyrolysis of the tar sands in the cyclone so as to effectively utilize smaller sized reactor vessels for reducing capitol and operating costs.

Westhoff, James D. (Laramie, WY); Harak, Arnold E. (Laramie, WY)

1989-01-01T23:59:59.000Z

25

Method and apparatus for hydrocarbon recovery from tar sands  

DOE Patents (OSTI)

A method and apparatus for utilizing tar sands having a broad range of bitumen content is disclosed. More particularly, tar sands are pyrolyzed in a cyclone retort with high temperature gases recycled from the cyclone retort to produce oil and hydrocarbon products. The spent tar sands are then burned at 2000/degree/F in a burner to remove residual char and produce a solid waste that is easily disposable. The process and apparatus have the advantages of being able to utilize tar sands having a broad range of bitumen content and the advantage of producing product gases that are free from combustion gases and thereby have a higher heating value. Another important advantage is rapid pyrolysis of the tar sands in the cyclone so as to effectively utilize smaller sized reactor vessels for reducing capitol and operating costs. 1 fig., 1 tab.

Westhoff, J.D.; Harak, A.E.

1988-05-04T23:59:59.000Z

26

Frame moduli of unconsolidated sands and sandstones  

SciTech Connect

In this study, the authors investigate the elastic moduli of the empty grain framework (the frame moduli) in unconsolidated sands and consolidated sandstones. The work was done to improve the interpretation of seismic amplitude anomalies and amplitude variations with offset (AVO) associated with hydrocarbon reservoirs. They developed a laboratory apparatus to measure the frame Poisson's ratio and Young's modulus of unconsolidated sands at seismic frequencies (0.2 to 155 Hz) in samples approximately 11 cm long. They used ultrasonic pulse velocity measurements to measure the frame moduli of consolidated sandstones. They found that the correlation coefficient between the frame Poisson's ratio [sigma][sub A] and the mineral Poisson's ratio [sigma][sub M] is 0.84 in consolidated sandstones and only 0.28 in unconsolidated sands. The range of [sigma][sub A] values in unconsolidated sands is 0.115 to 0.237 (mean = 0.187, standard deviation = 0.030), and [sigma][sub A] cannot be estimated without core or log analyses. Frame moduli analyses of core samples can be used to calibrate the interpretation of seismic amplitude anomalies and AVO effects. For use in areas without core or log analyses, the authors developed an empirical relation that can be used to estimate [sigma][sub A] in unconsolidated sands and sandstones from [sigma][sub M] and the frame P-wave modulus.

Spencer, J.W. Jr.; Cates, M.E.; Thompson, D.D. (Chevron Petroleum Technology Co., La Habra, CA (United States))

1994-09-01T23:59:59.000Z

27

Geochemical Evidence for an Eolian Sand Dam across the North and South Platte Rivers in Nebraska  

E-Print Network (OSTI)

microcracks saturating the ECC (Fig. 1(b)) before localization. This tight crack width is essential designation M45) along with green ECC mixture proportions (ECC with green foundry sand, ECC with bag house calcinator sand) Mixture proportions, *high-range water reducer M45 M45G M45 Calcin Cement 1 1 1 F-110 sand 0

Nebraska-Lincoln, University of

28

Velocities of deep water reservoir sands De-hua Han, University of Houston  

E-Print Network (OSTI)

and shale, which is not focus for this study. Sorting HP Shale ShallowDeep Sorting HP Shale Sorting HP Shale sands. Grain density is 2.65 gm/cc, typical for clean sands. Measured gas permeability ranged from 100 have revealed gradual effect of clay content on porosity and velocity of shaly sands and sandy shales

29

PROCESSING OF MONAZITE SAND  

DOE Patents (OSTI)

A process for the recovery of thorium, uranium, and rare earths from monazite sands is presented. The sands are first digested and dissolved in concentrated NaOH, and the solution is then diluted causing precipitation of uranium, thorium and rare earth hydroxides. The precipitate is collected and dissolved in HCl, and the pH of this solution is adjusted to about 6, precipitating the hydroxides of thorium and uranium but leaving the rare earths in solution. The rare earths are then separated from the solution by precipitation at a still higher pH. The thorium and uranium containing precipitate is redissolved in HNO/sub 3/ and the two elements are separated by extraction into tributyl phosphate and back extraction with a weakly acidic solution to remove the thorium.

Calkins, G.D.; Bohlmann, E.G.

1957-12-01T23:59:59.000Z

30

Sand consolidation method  

SciTech Connect

This patent describes a method of treating a subterranean, unconsolidated sand and petroleum-containing formation whose temperature is less than 200{degrees}F penetrated by at least one well, which is in fluid communication with at least a portion of the unconsolidated sand-containing subterranean formation, in order to form a permeable barrier in the treatment zone around the well which restrains the movement of sand particles into the well while permitting the passage of formation fluids including petroleum therethrough. It comprises introducing a non aqueous gas into the treatment zone of the formation to reduce the water content of the portion of the formation where the permeable barrier is to be formed to less than 5 percent by volume based on the volume of pore space to be treated; introducing an effective volume of treating fluid into the treatment zone, comprising a compound which is capable of being acid catalyzed to undergo condensation polymerization at formation temperatures, an anhydride of a strong acid, and a diluent for the polymerizable compound and the anhydride; and allowing the treating fluid to remain in the treatment zone for a period of time sufficient to ensure substantially complete polymerization.

Friedman, R.H.; Surles, B.W.

1991-08-20T23:59:59.000Z

31

Sand Hills EA  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

- - Office Name and State goes here Environmental Assessment Sand Hills Wind Energy Facility Albany County, Wyoming May 2011 High Desert District Rawlins Field Office The BLM's multiple-use mission is to sustain the health and productivity of the public lands for the use and enjoyment of present and future generations. The Bureau accomplishes this by managing such activities as outdoor recreation, livestock grazing, mineral development, and energy production, and by conserving natural, historical, cultural, and other resources on public lands. BLM/WY/PL-11/035+1430 WY-030-EA09-314 Contents Chapter Page Acronyms and Abbreviations .................................................................................................. ix

32

SAND REPORT SAND2003-0112  

E-Print Network (OSTI)

the Kauai Test Facility in Hawaii and the Tonopah Test Range in Nevada. The majority of employees work......................................................................................................27 4.2 Support of Nuclear Testing....................................................................................29 4.3 Environmental Testing

Fuerschbach, Phillip

33

Guide to Preparing SAND Reports  

E-Print Network (OSTI)

The Guide to Preparing SAND Reports contains guidelines for producing SAND Reports and other information releases. Its guidelines reflect DOE regulations and Sandia policy. The Guide includes in Section 1, policies for protecting and reproducing official information at Sandia, SAND number information, and Review & Approval procedures; in Section 2, basic writing instructions, which are illustrated in an annotated sample report; in Section 3, an explanation of the format, layout, and graphics of SAND Reports and a table that details the markings and legends needed for report covers and title pages; in Section 4, the procedures for reproducing and distributing SAND Reports; and in Section 5, information on presentations and conference papers, journal articles, book chapters, and brochures. The appendixes contain sections on Sandia's preferred style, usage, and grammar; equations; report references; and trademarks and copyrights. 4 May 1998 Intentionally Left Blank May 1998 5 Conten...

Tamara Locke Editor; Tamara K. Locke

1998-01-01T23:59:59.000Z

34

I SAND95-2448C  

Office of Scientific and Technical Information (OSTI)

SAND95-2448C SAND95-2448C eddfigt6qI7-*+ To be presented at the 32"d AIANASMEISAEIASEE Joint Propulsion Conference, Lake Buena Vista, FL, July 1-3, 1996 A SURVEY OF COMBUSTIBLE METALS, THERMITES, AND INTERMETALLICS FOR PYROTECHNIC APPLICATIONS* S. H. Fischer and M. C. Grubelich Sandia National Laboratories Albuquerque, NM 87185-1453 ABSTRACT Thermite mixtures, intermetallic reactants, and metal fuels have long been used in pyrotechnic applications. Advantage of these systems typically include high energy density, impact insensitivity, high combustion temperature, and a wide range of gas production. They generally exhibit high temperature stability, and possess insensitive ignition properties. In this paper, we review the applications, benefits, and characteristics

35

METHOD OF PROCESSING MONAZITE SAND  

DOE Patents (OSTI)

A method is given for the pretreatment of monazite sand with sodium hydroxide. When momazite sand is reacted with sodium hydroxide, the thorium, uranium, and rare earths are converted to water-insoluble hydrous oxides; but in the case of uranium, the precipitate compound may at least partly consist of a slightly soluble uranate. According to the patent, monazite sand is treated with an excess of aqueous sodium hydroxide solution, and the insoluble compounds of thorium, uranium, and the rare earths are separated from the aqueous solution. This solution is then concentrated causing sodium phosphate to crystallize out. The crystals are removed from the remaining solution, and the solution is recycled for reaction with a mew supply of momazite sand.

Calkins, G.D.

1957-10-29T23:59:59.000Z

36

Definition: Tar Sands | Open Energy Information  

Open Energy Info (EERE)

Definition Definition Edit with form History Facebook icon Twitter icon » Definition: Tar Sands Jump to: navigation, search Dictionary.png Tar Sands A resource, found in particular abundance in Canada, where viscous petroleum is mixed in with a layer of sand, clay, and water. The form of petroleum is often referred to as "bitumen". The resource has only recently been considered part of the world's oil reserves View on Wikipedia Wikipedia Definition Oil sands, tar sands or, more technically, bituminous sands, are a type of unconventional petroleum deposit. The oil sands are loose sand or partially consolidated sandstone containing naturally occurring mixtures of sand, clay, and water, saturated with a dense and extremely viscous form of petroleum technically referred to as bitumen (or colloquially tar due to

37

Sand consolidation method employing latex  

SciTech Connect

A method is described of treating a subterranean, unconsolidated sand and petroleum containing formation penetrated by at least one well, which is in fluid communication with at least a portion of the unconsolidated sand containing subterranean formation. This forms a flexible, permeable barrier around the well which restrains the movement of sand particles into the well while permitting the passage of formation fluids including petroleum there through. The method comprises: a. forming a predetermined quantity of a treating fluid comprising a water external phase emulsion having as its dispersed or discontinuous phase, a predetermined amount of an oil-insoluble rubber. The emulsion also contains a predetermined quantity of a material which hydrolyzes at reservoir temperature to form an acid; b. injecting the treating fluid into the formation to be consolidated; and c. leaving the fluid undisturbed in the formation for a predetermined period of time sufficient to allow the emulsion to break so the oil insoluble rubber coats the sand grains, forming a competent permeable barrier around the wellbore.

Friedman, R.H.

1987-03-17T23:59:59.000Z

38

Characteristics and Applications of Copper Stamp Sand  

Science Conference Proceedings (OSTI)

The chemical, physical properties and antimicrobial activity of stamp sand were investigated, ... Characterization of Fluorescent Lamp Glass Waste Powders for ...

39

METHOD OF PROCESSING MONAZITE SAND  

DOE Patents (OSTI)

A process is described for recovering thorium, uranium, and rare earth values from monazite sand. The monazite sand is first digested with sulfuric acid and the resulting "monazite sulfate" solution is adjusted to a pH of between 0.4 and 3.0, and oxalate anions are added causing precipitation of the thorium and the rare earths as the oxalates. The oxalate precipitate is separated from the uranium containing supernatant solution, and is dried and calcined to the oxides. The thorium and rare earth oxides are then dissolved in nitric acid and the solution is contacted with tribntyl phosphate whereby an organic extract phase containing the cerium and thorium values is obtained, together with an aqueous raffinate containing the other rare earth values. The organic phase is then separated from the aqueous raffinate and the cerium and thorium are back extracted with an aqueous medium.

Welt, M.A.; Smutz, M.

1958-08-26T23:59:59.000Z

40

Recent government efforts regarding tar sands  

SciTech Connect

Conclusions from a workshop on tar sands are discussed. The workshop participants came to 3 conclusions: any oil-impregnated rock that is mined or quarried and then processed on the surface should be considered tar sands; some physical parameter should be used to differentiate tar sands from heavy oils, e.g., viscosity; and the dividing line between tar sands and heavy oil should be a point above which there is not currently significant commercial production. The resulting definition states that tar sand is any consolidated or unconsolidated rock other than coal, oil shale, or gilsonite, that contains a hydrocarbonaceous material with a gas-free viscosity, measured at reservoir temperature, greater than 10,000 cp, or contains a hydrocarbonaceous material that is extracted from the mined or quarried rock. Some consideration of resuming tar sands leasing also is discussed.

Pumphrey, D.

1980-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Shallow horizontal drilling in unconsolidated sands offshore California  

SciTech Connect

Four shallow horizontal wells were drilled from Platform C in Dos Cuadras field offshore California to recover reserves inaccessible with conventional drilling techniques. The wells had true vertical depths (TVD's) ranging from 746 to 989 ft with total horizontal displacements from 1,613 to 3,788 ft. The wells had horizontal displacement TVD ratios up to 3.95. The targets were unconsolidated, high-permeability sands. This paper details well planning, drilling, and completion.

Payne, J.D.; Bunyak, M.J. (Unocal Corp., Los Angeles, CA (United States)); Huston, C.W. (Smith International Inc., Tyler, TX (United States))

1993-12-01T23:59:59.000Z

42

technology offer SandTES -High Temperature Sand Thermal Energy Storage  

E-Print Network (OSTI)

technology offer SandTES - High Temperature Sand Thermal Energy Storage key words: High Temperature together with Dr. Eisl of ENRAG GmbH. Background Thermal energy storage (TES) systems are essential Energy Storage | Fluidized Bed | Sand | The invention consists of a fluidized bed with internal heat

Szmolyan, Peter

43

Materials Science and Engineering in the Canadian Oil Sands  

Science Conference Proceedings (OSTI)

While people have heard about these "tar sands" in the news, relatively few know what oil sands are, and how they are extracted/processed. This presentation ...

44

Generation of sand bars under surface waves  

E-Print Network (OSTI)

(cont.) Experiments were performed in a large wave flume to validate the theory and to study additional aspects of sand bar evolution. The wave envelope and bar profile were recorded for low and high beach reflection, ...

Hancock, Matthew James, 1975-

2005-01-01T23:59:59.000Z

45

New method for sand control and well stimulation in unconsolidated dirty sands  

SciTech Connect

A new technique, the Solder Glass sand consolidation well completion method, has been developed which allows unlimited drawdown and improves productivity in wells completed in unconsolidated formations containing shales and clays. This technique eliminates the problems of sand production and fines migration by artificially consolidating a volume of reservoir sand near the wellbore. The consolidation is resistant to high temperature, chemical attack, and degradation resulting from high velocity fluid flow. Additionally, porosity and permeability in the consolidated volume of reservoir sand are improved as a result of irreversible dehydration of clays. 12 refs.

Aslesen, K.S.; Short, C.J.; Terwilliger, P.L.

1981-01-01T23:59:59.000Z

46

Secure Fuels from Domestic Resources- Oil Shale and Tar Sands  

Energy.gov (U.S. Department of Energy (DOE))

Profiles of Companies Engaged in Domestic Oil Shale and Tar Sands Resource and Technology Development

47

Sand-control alternatives for horizontal wells  

SciTech Connect

This paper reports that it has been well documented that horizontal completions increase production rates, as much as two to five times those of conventional techniques, because more of the producing formation is exposed to the wellbore. Although productivity improvements are highly sensitive to reservoir parameters, it is becoming generally accepted that optimum horizontal lengths will be 2,000 to 4,000 ft. The length of these completions generally causes the velocity of the fluid at the sandface to be an order of magnitude less than that observed in conventional completions. Because drag forces contributed to sand production, horizontal wells can produce at higher sand-free flow rates than conventional completions in the same reservoir. While it is frequently argued that horizontal wells do not need sand control, the potential for sand production increases significantly as reserves deplete and rock stresses increase. This is becoming more evident today in several major North Sea oil fields with conventional completions. Also, many unconsolidated formations produce sand for the first time with the onset of water production, a typical problem in such areas as the Gulf of Mexico. Operators must decide whether to implement sand control in the original horizontal-completion program because of an immediate concern or because the potential exists for a problem to arise as the well matures.

Zaleski, T.E. Jr. (Baker Sand Control (US))

1991-05-01T23:59:59.000Z

48

Foundry Sand Reclamation: CMP Report No. 90-6  

Science Conference Proceedings (OSTI)

Current environmental regulations have created a situation where the disposal of waste foundry sand has become difficult and expensive. One solution to this problem is the use of a sand reclamation system which "cleans" the sand to a sufficient degree to allow re-use of the sand in the foundry sand system. A large number of sand binder systems are in use for various reasons of cost and performance characteristics. There are also three main methods of sand reclamation and combinations of these. A basic un...

1991-11-30T23:59:59.000Z

49

Factors affecting home range of mallard pairs  

SciTech Connect

Certain habitat and social factors were investigated for their effect on home range size of mallard (Anas platyhynchos) pairs breeding in a forested region of north-central Minnesota during the spring of 1971--72. Data from 31 radio-marked hens and drakes were used, but primary emphasis was placed on 8 pairs (5 with both members of the pair marked). Pairs were radio-tracked on river marsh areas, river channels, and large sand lakes to provide comparative data for evaluating home range size differences. Home ranges varied from an average of 53 ha for pairs using primarily river habitat to 871 ha for pairs using only large sand lakes. River and lake shorelines varied considerably in species and density of vegetation. Interaction between pairs as well as density of flocked males appeared to be influenced by these habitat differences with resultant effects on home range sizes.

Riechmann, J.H.

1976-06-01T23:59:59.000Z

50

SAND2011-6342A  

National Nuclear Security Administration (NNSA)

Computational Physics-Methods References 1 S.A. Silling, "Reformulation of elasticity theory for discontinuities and long-range forces," J. Mech. Phys. Solids 48 175-209...

51

SAND2006-6448 P  

NLE Websites -- All DOE Office Websites (Extended Search)

and disposal (facility) TTR Tonopah Test Range U USAF U.S. Air Force USFS U.S. Forest Service USGS U.S. Geological Survey UST underground storage tank V VOC volatile...

52

Canyon dissolution of sand, slag, and crucible residues  

Science Conference Proceedings (OSTI)

An alternative to the FB-Line scrap recovery dissolver was desired for the dissolution of sand, slag, and crucible (SS{ampersand}C) residues from the plutonium reduction process due to the potential generation of hydrogen gas concentrations above the lower flammability limit. To address this concern, a flowsheet was developed for the F-Canyon dissolvers. The dissolvers are continually purged with nominally 33 SCFM of air; therefore the generation of flammable gas concentrations should not be a concern. Following removal of crucible fragments, small batches of the remaining sand fines or slag chunks containing less than approximately 350 grams of plutonium can be dissolved using the center insert in each of the four annular dissolver ports to address nuclear criticality safety concerns. Complete dissolution of the sand fines and slag chunks was achieved in laboratory experiments by heating between 75 and 85 degrees Celsius in a 9.3M nitric acid/0.013M (hydrogen) fluoride solution. Under these conditions, the sand and slag samples dissolved between 1 and 3 hours. Complete dissolution of plutonium and calcium fluorides in the slag required adjusting the dissolver solution to 7.5 wt% aluminum nitrate nonahydrate (ANN). Once ANN was added to a dissolver solution, further dissolution of any plutonium oxide (PuO2) in successive charges was not practical due to complexation of the fluoride by aluminum. During the laboratory experiments, well mixed solutions were necessary to achieve rapid dissolution rates. When agitation was not provided, sand fines dissolved very slowly. Measurement of the hydrogen gas generation rate during dissolution of slag samples was used to estimate the amount of metal in the chunks. Depending upon the yield of the reduction, the values ranged between approximately 1 (good yield) and 20% (poor yield). Aging of the slag will reduce the potential for hydrogen generation as calcium metal oxidizes over time. The potential for excessive corrosion in the dissolvers was evaluated using experimental data reported in the literature. Corrosion data at the exact flowsheet conditions were not available; however, the corrosion rate for 304L stainless steel (wrought material) corrosion coupons in 10M nitric acid/0.01M hydrofluoric acid at 95 degrees Celsius was reported as 21 mils per year. If the fluoride in the dissolver is complexed with aluminum, the corrosion rate will decrease to approximately 5 mils per year.

Rudisill, T.S.; Gray, J.H.; Karraker, D.G.; Chandler, G.T.

1997-12-01T23:59:59.000Z

53

Sand control method employing special hydraulic fracturing technique  

SciTech Connect

A novel sand control method is disclosed wherein high viscosity, high sand concentration, fracturing fluids are pumped through sets of vertically oriented perforations in borehole casings located in unconsolidated or loosely consolidated pay zones. Various techniques are utilized to insure that sand fills disposed on either side of the borehole casing cover and substantially overlap each borehole casing perforation set. Procedures are then followed to bring the well into production without washing out the sand fills in these areas, whereby the resulting perforation-sand fill configurations effectively control sand production from the treated zone.

Medlin, W.L.; Mullins, L.D.; Zumwalt, G.L.

1983-04-05T23:59:59.000Z

54

Granular size segregation in underwater sand ripples  

E-Print Network (OSTI)

We report an experimental study of a binary sand bed under an oscillating water flow. The formation and evolution of ripples is observed. The appearance of a granular segregation is shown to strongly depend on the sand bed preparation. The initial wavelength of the mixture is measured. In the final steady state, a segregation in volume is observed instead of a segregation at the surface as reported before. The correlation between this phenomenon and the fluid flow is emphasised. Finally, different ``exotic'' patterns and their geophysical implications are presented.

G. Rousseaux; H. Caps; J. -E. Wesfreid

2004-03-29T23:59:59.000Z

55

Pore-scale mechanisms of gas flow in tight sand reservoirs  

E-Print Network (OSTI)

pore space. Although the grains in tight sand samples do notfluid displacement. For tight sands, the simulations predictflow properties of tight sand imply that a small amount of

Silin, D.

2011-01-01T23:59:59.000Z

56

The Coupling of Gravity Waves and Turbulence at White Sands, New Mexico, from VHF Radar Observations  

Science Conference Proceedings (OSTI)

Doppler spectra taken with the VHF Doppler radar at White Sands Missile Range are used to describe the winds and turbulence for 10 days in March?April 1991. The large power aperture product of this radar provides excellent data coverage in 150-m ...

G. D. Nastrom; F. D. Eaton

1993-01-01T23:59:59.000Z

57

Sand Bluff Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Sand Bluff Wind Farm Sand Bluff Wind Farm Jump to: navigation, search Name Sand Bluff Wind Farm Facility Sand Bluff Wind Farm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner E.On Climate & Renewables Developer E.On Climate & Renewables Energy Purchaser Direct Energy Location Near Big Spring TX Coordinates 32.201622°, -101.404799° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":32.201622,"lon":-101.404799,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

58

CO{sub 2}/sand fracturing in Devonian shales  

Science Conference Proceedings (OSTI)

A total of five carbon dioxide (CO{sub 2})/sand well stimulations were successfully executed with two Devonian shale operators in Perry and Pike Counties, Kentucky. This new stimulation method offers a minimum formation damage proppant stimulation approach for natural gas producers in the United States. Some operators have been concerned about the frac fluid formation damage associated with the water and chemicals used in conventional foam stimulations, whereas other operators have been concerned about the lack of proppant in straight nitrogen fracs used by service companies today. Two carefully screened geological areas of established Devonian shale production were selected based on active ongoing drilling and completion operations. One selected control area contained an existing set of wells with established production histories. More specifically, one operator furnished three offset wells which were stimulated with the carbon dioxide/sand frac method. The quantity of proppant and fluids pumped during each well stimulation ranged from 23,000 to 43,000 pounds of proppant and from 120 to 160 tons of liquid carbon dioxide. Another operator furnished two offset wells which were each stimulated with approximately 47,000 pounds of proppant and 120 tons of carbon dioxide. The logistics and field layout of a typical carbon dioxide/sand frac treatment has been described and highlighted. The importance and unique aspects of the closed system blender that is required for job execution is discussed. Five stimulation treatments have been reviewed, and stimulation and preliminary production data compared to offset wells stimulated with nitrogen, and explosives. Initial production results indicate more than a 50 percent increase in production rate compared to nitrogen fraced wells in the Pike County area.

Yost, A.B. II [USDOE Morgantown Energy Technology Center, WV (United States); Mazza, R.L. [Petroleum Consulting Services, Canton, OH (United States); Gehr, J.B. [Natural Gas Resources Corporation (United States)

1993-12-31T23:59:59.000Z

59

The Time of Sands: Quartz-rich Sand Deposits as a Renewable Resource  

E-Print Network (OSTI)

rich Sand Deposits as a Renewable Resource Nelson R. Shaffercan even be considered a renewable resource. The reader willbuild our society, and its renewable nature. We are not the

Shaffer, Nelson R.

2006-01-01T23:59:59.000Z

60

Imaging of Acoustic Waves in Sand  

SciTech Connect

There is considerable interest in detecting objects such as landmines shallowly buried in loose earth or sand. Various techniques involving microwave, acoustic, thermal and magnetic sensors have been used to detect such objects. Acoustic and microwave sensors have shown promise, especially if used together. In most cases, the sensor package is scanned over an area to eventually build up an image or map of anomalies. We are proposing an alternate, acoustic method that directly provides an image of acoustic waves in sand or soil, and their interaction with buried objects. The INEEL Laser Ultrasonic Camera utilizes dynamic holography within photorefractive recording materials. This permits one to image and demodulate acoustic waves on surfaces in real time, without scanning. A video image is produced where intensity is directly and linearly proportional to surface motion. Both specular and diffusely reflecting surfaces can be accomodated and surface motion as small as 0.1 nm can be quantitatively detected. This system was used to directly image acoustic surface waves in sand as well as in solid objects. Waves as frequencies of 16 kHz were generated using modified acoustic speakers. These waves were directed through sand toward partially buried objects. The sand container was not on a vibration isolation table, but sat on the lab floor. Interaction of wavefronts with buried objects showed reflection, diffraction and interference effects that could provide clues to location and characteristics of buried objects. Although results are preliminary, success in this effort suggests that this method could be applied to detection of buried landmines or other near-surface items such as pipes and tanks.

Deason, Vance Albert; Telschow, Kenneth Louis; Watson, Scott Marshall

2003-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Weber Group PUBLICATIONS  

E-Print Network (OSTI)

and Related Materials," Proc. Internat. Conf. Tbilisi (USSR) 1979, Eds. G.P. Kekelidze and V.I. Shakhovtsov, p Materials," Proc. Internat. Conf. Tbilisi (USSR) 1979, Eds. G.P. Kekelidze and V.I. Shakhovtsov, p. 296

Weber, Eicke R.

62

Well completion process for formations with unconsolidated sands  

DOE Patents (OSTI)

A method for consolidating sand around a well, involving injecting hot water or steam through well casing perforations in to create a cement-like area around the perforation of sufficient rigidity to prevent sand from flowing into and obstructing the well. The cement area has several wormholes that provide fluid passageways between the well and the formation, while still inhibiting sand inflow.

Davies, David K. (Kingwood, TX); Mondragon, III, Julius J. (Redondo Beach, CA); Hara, Philip Scott (Monterey Park, CA)

2003-04-29T23:59:59.000Z

63

Oil shale and tar sands technology: recent developments  

SciTech Connect

The detailed, descriptive information in this book is based on US patents, issued since March 1975, that deal with the technology of oil shale and tar sands. The book contains an introductory overview of the subject. Topics included are oil shale retorting, in situ processing of oil shale, shale oil refining and purification processes, in situ processing of tar sands, tar sands separation processes.

Ranney, M.W.

1979-01-01T23:59:59.000Z

64

Trace metals in heavy crude oils and tar sand bitumens  

SciTech Connect

Fe, Ni, and V are considered trace impurities in heavy crude oils and tar sand bitumens. In order to understand the importance of these metals, we have examined several properties: (1) bulk metals levels, (2) distribution in separated fractions, (3) size behavior in feeds and during processing, (4) speciation as a function of size, and (5) correlations with rheological properties. Some of the results of these studies show: (1) V and Ni have roughly bimodal size distributions, (2) groupings were seen based on location, size distribution, and Ni/V ratio of the sample, (3) Fe profiles are distinctively different, having a unimodal distribution with a maximum at relatively large molecular size, (4) Fe concentrations in the tar sand bitumens suggest possible fines solubilization in some cases, (5) SARA separated fractions show possible correlations of metals with asphaltene properties suggesting secondary and tertiary structure interactions, and (6) ICP-MS examination for soluble ultra-trace metal impurities show the possibility of unexpected elements such as U, Th, Mo, and others at concentrations in the ppB to ppM range. 39 refs., 13 figs., 5 tabs.

Reynolds, J.G.

1990-11-28T23:59:59.000Z

65

SAND76-0260 Unlimited Release  

NLE Websites -- All DOE Office Websites (Extended Search)

SAND76-0260 SAND76-0260 Unlimited Release Printed July 1976 . POWER SUPPLIES FOR SPACE SYSTEMS QUALITY ASSURANCE BY SANDIA LABORATORIES Robert L. Hannigan Robert R. Harnar Electronic and Electrical Devices Division 951 2 Sandia Laboratories Albuquerque, NM 87115 AB STRAC T This report summarizes the Sandia Laboratories participation in Quality Assurance programs for Radioisotopic Thermoelectric Generators which have been used i n space systems over the past 10 years. Basic elements of this QA program a r e briefly de- scribed and recognition of assistance from other Sandia organizations is included. Descriptions of the various systems f o r which Sandia has had the QA responsibility a r e presented, including SNAP 1 9 (Nimbus, Pioneer, Viking), SNAP 27 (Apollo),

66

Solvent extraction of Southern US tar sands  

SciTech Connect

The Department of Chemical Engineering at the University of Arkansas, in association with Diversified Petroleum Recovery, Inc. (DPR) of Little Rock, Arkansas, has been developing a solvent extraction process for the recovery of bitumen from tar sands for the past five years. The unique feature of the process is that the bitumen is recovered from the solvent by contacting with a co-solvent, which causes the bitumen to precipitate. The overall purpose of this project is to study both the technical and economic feasibility of applying this technology for recovery of bitumen from tar sands by (1) investigating the socioeconmic factors which affect (a) plant siting and (b) the market value of recovered bitumen; (2) operating a process demonstration unit at the rate of 1 lb/hr recovered bitumen while producing clean sand and recyclable solvents; and (3) determine the economic conditions which will make a bitumen recovery project economical. DPR has analyzed the historical trends of domestic production, consumption, discoveries and reserves of crude oil. They have started an investigation of the volatility in the price of crude oil and of gasoline prices and of the differential between gasoline and crude oil. DPR continues to analyze the geographical movement and demand for asphalt products. Utah does not appear economically attractive as a site for a bitumen from tar sands asphalt plant. Oklahoma sites are now being studied. This report also contains the quarterly progress report from a University of Nevada study to determine bitumen composition, oxygen uptake rates, and viscosities of Alabama and Utah bitumens. Both reports have been indexed separately for inclusion on the data base.

Penney, W.R.

1990-01-01T23:59:59.000Z

67

Western gas sands: Technology status report  

Science Conference Proceedings (OSTI)

Research on western gas sands is conducted by the US Department of Energy's Morgantown Technology Center to encourage the development of very low permeability gas sands in the western United States. The current search is an outgrowth of earlier Government research on tight sands in which nuclear and massive hydraulics fracturing stimulations were tested without definitive results. Based on input from the gas industry, universities, and geologic and engineering consulting firms, activites were broadened to include fundamental research and development. Consequently, the focus of the research for the last several years has been on improving diagnostic instruments for evaluating reservoir and stimulation performances, interpreting geophysical and engineering data, and stimulation techniques. Intergrated geologic studies of three depositional basins that contain tight lenticular sandstone units have also been pursued as part of this new effort. To date, the following tentative conclusions have been formulated: The permeability of the tight gas sands can be as much as three to four orders of magnitude lower than that of conventional gas deposits. Nineteen western geologic basins and trends have been identified that contain significant volumes of tight gas. Gas resources in the priority geologic basins have been estimated as follows: Piceance Basin, 420 Tcf.; Greater Green River Basin, 4971 Tcf.; and Uinta Basin, 21 Tcf. The critical parameters for successfully developing tight sandstone resources are the presence of natural fractures within a reservoir and the effective propped length of hydraulically induced fractures. Stimulation technology is presently insufficient to efficiently recover gas from lenticular, tight reservoirs. 15 refs., 14 figs., 3 tabs.

Not Available

1988-01-01T23:59:59.000Z

68

EA-1581: Sand Hills Wind Project, Wyoming  

Energy.gov (U.S. Department of Energy (DOE))

The Bureau of Land Management, with DOE’s Western Area Power Administration as a cooperating agency, is preparing this EA to evaluate the environmental impacts of a proposal to construct, operate, and maintain the Sand Hills Wind Energy Facility on private and federal lands in Albany County, Wyoming. If the proposed action is implemented, Western would interconnect the proposed facility to an existing transmission line.

69

Guide to preparing SAND reports. Revised  

SciTech Connect

This guide contains basic information needed to produce a SAND report. Its guidelines reflect DOE regulation and Sandia policy. The guide includes basic writing instructions in an annotated sample report; guidance for organization, format, and layout of reports produced by line organizations; and information about conference papers, journal articles, and brochures. The appendixes contain sections on Sandia`s preferred usage, equations, references, copyrights and permissions, and publishing terms.

Locke, T.K. [ed.

1996-04-01T23:59:59.000Z

70

The performance of the small-angle diffractometer, SAND at IPNS.  

Science Conference Proceedings (OSTI)

The time-of-flight small-angle diffractometer SAND has been serving the scientific user community since 1996. One notable feature of SAND is its capability to measure the scattered intensity in a wide Q (4{pi}sin{theta}/{lambda}, where 2{theta} is the scattering angle and {lambda} is the wavelength of the neutrons) range of 0.0035 to 0.5 {angstrom}{sup {minus}1} in a single measurement. The optical alignment system makes it easy to set up the instrument and the sample. The cryogenically cooled MgO filter reduces the fast neutrons over two orders of magnitude, while still transmitting over 70% of the cold neutrons. A drum chopper running at 15 Hz suppresses the delayed neutron background. SAND has a variety of ancillary equipment to control the sample environment. In this paper we describe the features of the SAND instrument, compare its data on a few standard samples with those measured at well established centers in the world, and display two scientific examples which take advantage of measuring data in a wide Q-range in a single measurement. With a new set of tight collimators the Q{sub min} can be lowered to 0.002 {angstrom}{sup {minus}1} and the presently installed high-angle bank of detectors will extend the Q{sub max} to 2 {angstrom}{sup {minus}1}.

Thiyagarajan, P.

1998-07-17T23:59:59.000Z

71

Policy Analysis of the Canadian Oil Sands Experience  

SciTech Connect

For those who support U.S. oil sands development, the Canadian oil sands industry is often identified as a model the U.S. might emulate, yielding financial and energy security benefits. For opponents of domestic oil sands development, the Canadian oil sands experience illustrates the risks that opponents of development believe should deter domestic policymakers from incenting U.S. oil sands development. This report does not seek to evaluate the particular underpinnings of either side of this policy argument, but rather attempts to delve into the question of whether the Canadian experience has relevance as a foundational model for U.S. oil sands development. More specifically, this report seeks to assess whether and how the Canadian oil sands experience might be predictive or instructive in the context of fashioning a framework for a U.S. oil sands industry. In evaluating the implications of these underpinnings for a prospective U.S. oil sands industry, this report concentrates on prospective development of the oil sands deposits found in Utah.

None, None

2013-09-01T23:59:59.000Z

72

Oil shale, tar sands, and related materials  

SciTech Connect

This sixteen-chapter book focuses on the many problems and the new methodology associated with the commercialization of the oil shale and tar sand industry. Topics discussed include: an overview of the Department of Energy's oil shale R, D, and D program; computer simulation of explosive fracture of oil shale; fracturing of oil shale by treatment with liquid sulfur dioxide; chemistry of shale oil cracking; hydrogen sulfide evolution from Colorado oil shale; a possible mechanism of alkene/alkane production in oil shale retorting; oil shale retorting kinetics; kinetics of oil shale char gasification; a comparison of asphaltenes from naturally occurring shale bitumen and retorted shale oils: the influence of temperature on asphaltene structure; beneficiation of Green River oil shale by density methods; beneficiation of Green River oil shale pelletization; shell pellet heat exchange retorting: the SPHER energy-efficient process for retorting oil shale; retorted oil shale disposal research; an investigation into the potential economics of large-scale shale oil production; commercial scale refining of Paraho crude shale oil into military specification fuels; relation between fuel properties and chemical composition; chemical characterization/physical properties of US Navy shale-II fuels; relation between fuel properties and chemical composition: stability of oil shale-derived jet fuel; pyrolysis of shale oil residual fractions; synfuel stability: degradation mechanisms and actual findings; the chemistry of shale oil and its refined products; the reactivity of Cold Lake asphaltenes; influence of thermal processing on the properties of Cold Lake asphaltenes: the effect of distillation; thermal recovery of oil from tar sands by an energy-efficient process; and hydropyrolysis: the potential for primary upgrading of tar sand bitumen.

Stauffer, H.C.

1981-01-01T23:59:59.000Z

73

EA-1581: Sand Hills Wind Project, Wyoming | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

81: Sand Hills Wind Project, Wyoming 81: Sand Hills Wind Project, Wyoming EA-1581: Sand Hills Wind Project, Wyoming Location of the proposed Sand Hills Wind Project, near Laramie, Wyoming Location of the proposed Sand Hills Wind Project, near Laramie, Wyoming Summary The Bureau of Land Management, with DOE's Western Area Power Administration as a cooperating agency, is preparing this EA to evaluate the environmental impacts of a proposal to construct, operate, and maintain the Sand Hills Wind Energy Facility on private and federal lands in Albany County, Wyoming. If the proposed action is implemented, Western would interconnect the proposed facility to an existing transmission line. Public Comment Opportunities No public comment opportunities available at this time. List of Available Documents

74

Sand Mountain Electric Cooperative - Residential Heat Pump Loan Program |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sand Mountain Electric Cooperative - Residential Heat Pump Loan Sand Mountain Electric Cooperative - Residential Heat Pump Loan Program Sand Mountain Electric Cooperative - Residential Heat Pump Loan Program < Back Eligibility Residential Savings Category Heating & Cooling Commercial Heating & Cooling Heat Pumps Program Info State Alabama Program Type Utility Loan Program Rebate Amount 7% interest rate 5 or 10 year pay schedule maximum of $12,000 Provider Sand Mountain Electric Cooperative The Sand Mountain Electric Cooperative offers a heat pump loan program to eligible residential members. To qualify, members must have had power with Sand Mountain Electric Cooperative for at least one year, have the home electric bill and deeds in the same name, and pass a credit check. Heat pumps must be installed by a [http://www.smec.coop/heatpumpcontractors.htm

75

Unconsolidated sand grain shape, size impact frac-pack design  

SciTech Connect

The shape and size of sand grains, as well as the saturating fluid, influence the mechanical properties of unconsolidated sands and need to be considered in frac-pack design. These mechanical properties of unconsolidated properties of unconsolidated sands play an important role in determining the geometry of frac-pack treatments. Stress-strain curves obtained for unconsolidated sands at elevated stresses show highly nonlinear hysteretic behavior. The impact of these findings on frac-pack design can be significant. The nonlinear elastic properties of unconsolidated sand can give rise to some unique features in the pressure response and in the fracture geometry that may not be observed in hard rocks. This article focuses on the impact of mechanical properties of poorly consolidated and unconsolidated sands on the geometry of frac packs. The paper discusses frac packs, mechanical properties (Young`s modulus, shear failure) and effective treatments.

Wang, E.; Sharma, M.M. [Univ. of Texas, Austin, TX (United States)

1997-05-19T23:59:59.000Z

76

Oil shales and tar sands: a bibliography  

DOE Green Energy (OSTI)

Five thousand one hundred forty-two citations of reports, journal articles, patents, conference papers, and monographs resulting from research on oil shales and tar sands are presented. These citations and approximately 5100 additional citations are a part of the Department of Energy's Energy Data Base. The citations, with abstracts, are arranged by subject category. Within the categories references to reports are listed in alphanumeric order by report number. Other citations follow in inverse chronological order. Five indexes are provided: Corporate, Author, Subject, Contract Number, and Report Number.

Grissom, M.C. (ed.)

1981-04-01T23:59:59.000Z

77

Flotation behavior of digested asphalt ridge tar sands  

SciTech Connect

The hot water process for Utah tar sands differs from that used for Canadian tar sands due to inherent differences in respective bitumen viscosities and the nature of bitumen-sand association. Although contact angle measurements of solvent extracted Asphalt Ridge bitumen indicated moderate hydrophobicity, air bubble attachment to the bitumen concentrate is not possible. This suggests that flotation separation is dependent on air bubble entrapment. Improved separation at higher flotation temperatures was due to the decrease in bitumen viscosity. 16 refs.

Smith, R.J.; Miller, J.D.

1981-12-01T23:59:59.000Z

78

SANDIA REPORT SAND93-1076  

Office of Scientific and Technical Information (OSTI)

SANDIA SANDIA REPORT SAND93-1076 * u_qo UnlimitedRelease 1 Pdnted November 1993 :ii l Standard Testing Procedures for Optical Fiber and Unshielded Twisted Pair at Sandia National Laboratories R. L. Adams Pe,_e,d by Sand!a Nm#ocml L.abomlodN Albuquerque, NewMexlooI71U and Uvermore,California$M860 for the UnitedStatesDepartment ofEnergy underContract DE.ACOI-MALIIf_D SF2900Q(8-81 } _IITRIEIUTION OF THiS DGCU,VltZNT 18 UNLIMITED k Issued by Sandia National Laboratories, operated for the United States Department of Energy by Sandia Corporation. NOTICE. This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, nor any of their c_ntractors, subcontractors, or their employees, makes any warranty, express or implied, or assumes any legal liability

79

Microstructural characterization of a Canadian oil sand  

E-Print Network (OSTI)

The microstructure of oil sand samples extracted at a depth of 75 m from the estuarine Middle McMurray formation (Alberta, Canada) has been investigated by using high resolution 3D X-Ray microtomography ($\\mu$CT) and Cryo Scanning Electron Microscopy (CryoSEM). $\\mu$CT images evidenced some dense areas composed of highly angular grains surrounded by fluids that are separated by larger pores full of gas. 3D Image analysis provided in dense areas porosity values compatible with in-situ log data and macroscopic laboratory determinations, showing that they are representative of intact states. $\\mu$CT hence provided some information on the morphology of the cracks and disturbance created by gas expansion. The CryoSEM technique, in which the sample is freeze fractured within the SEM chamber prior to observation, provided pictures in which the (frozen) bitumen clearly appears between the sand grains. No evidence of the existence of a thin connate water layer between grains and the bitumen, frequently mentioned in th...

Dinh, Hong Doan; Nauroy, Jean-François; Tang, Anh-Minh; Souhail, Youssef; 10.1139/T2012-072

2013-01-01T23:59:59.000Z

80

TESTING OF TMR SAND MANTIS FINAL REPORT  

SciTech Connect

Screening tests of Sand Mantis candidate materials selected for erosion resistance have been completed. The results of this testing identified that over a relatively short period of operation (<1 hour), measurable erosion will occur in each of the candidate zoom tube materials given equal operating exposure. Additionally, this testing has shown that erosion of the rubber discharge hose directly downstream of the vehicle could be expected to limit the service life of the discharge hose. On the basis of these test results, SRNL recommends the following; {lg_bullet} redesign of critical system components (e.g., zoom tube, discharge hose) should be conducted to improve system characteristics relative to erosion and capitalize on the results of this testing, {lg_bullet} continued efforts to deploy the Sand Mantis should include testing to better define and optimize operating parameters, and gain an understanding of system dynamics, {lg_bullet} discontinue wear testing with the selected materials pending redesign of critical system components (1st recommendation) and inclusion of other candidate materials. The final selection of additional candidate materials should be made following design changes, but might include a Stellite alloy or zirconia.

Krementz, D; William Daugherty, W

2007-06-12T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Occurrence of gas hydrate in Oligocene Frio sand: Alaminos Canyon Block 818: Northern Gulf of Mexico  

SciTech Connect

A unique set of high-quality downhole shallow subsurface well log data combined with industry standard 3D seismic data from the Alaminos Canyon area has enabled the first detailed description of a concentrated gas hydrate accumulation within sand in the Gulf of Mexico. The gas hydrate occurs within very fine grained, immature volcaniclastic sands of the Oligocene Frio sand. Analysis of well data acquired from the Alaminos Canyon Block 818 No.1 ('Tigershark') well shows a total gas hydrate occurrence 13 m thick, with inferred gas hydrate saturation as high as 80% of sediment pore space. Average porosity in the reservoir is estimated from log data at approximately 42%. Permeability in the absence of gas hydrates, as revealed from the analysis of core samples retrieved from the well, ranges from 600 to 1500 millidarcies. The 3-D seismic data reveals a strong reflector consistent with significant increase in acoustic velocities that correlates with the top of the gas-hydrate-bearing sand. This reflector extends across an area of approximately 0.8 km{sup 2} and delineates the minimal probable extent of the gas hydrate accumulation. The base of the inferred gas-hydrate zone also correlates well with a very strong seismic reflector that indicates transition into units of significantly reduced acoustic velocity. Seismic inversion analyses indicate uniformly high gas-hydrate saturations throughout the region where the Frio sand exists within the gas hydrate stability zone. Numerical modeling of the potential production of natural gas from the interpreted accumulation indicates serious challenges for depressurization-based production in settings with strong potential pressure support from extensive underlying aquifers.

Boswell, R.D.; Shelander, D.; Lee, M.; Latham, T.; Collett, T.; Guerin, G.; Moridis, G.; Reagan, M.; Goldberg, D.

2009-07-15T23:59:59.000Z

82

Thermal reclaimer apparatus for a thermal sand reclamation system  

SciTech Connect

A thermal reclaimer apparatus is disclosed for thermally removing from the used foundry sand the organic matter that is present therein. The subject thermal reclaimer apparatus includes chamber means in which the used foundry sand is heated to a predetermined temperature for a preestablished period in order to accomplish the burning away of the organic matter that the used foundry sand contains. The chamber means includes inlet means provided at one end thereof and outlet means provided at the other end thereof. Feed means are cooperatively associated with the pipe means and thereby with the inlet means for feeding the used foundry sand through the inlet means into the chamber means. The subject thermal reclaimer apparatus further includes rotating means operative for effecting the rotation of the chamber means as the used foundry sand is being heated therein. The chamber means has cooperatively associated therewith burner means located at the same end thereof as the outlet means. The burner means is operative to effect the heating of the used foundry sand to the desired temperature within the chamber means. Tumbling means are provided inside the chamber means to ensure that the used foundry sand is constantly turned over, i.e., tumbled, and that the lumps therein are broken up as the chamber means rotates. Lastly, the used foundry sand from which the organic matter has been removed leaves the chamber means through the outlet means.

Deve, V.

1984-02-07T23:59:59.000Z

83

Tight gas sands study breaks down drilling and completion costs  

Science Conference Proceedings (OSTI)

Given the high cost to drill and complete tight gas sand wells, advances in drilling and completion technology that result in even modest cost savings to the producer have the potential to generate tremendous savings for the natural gas industry. The Gas Research Institute sponsored a study to evaluate drilling and completion costs in selected tight gas sands. The objective of the study was to identify major expenditures associated with tight gas sand development and determine their relative significance. A substantial sample of well cost data was collected for the study. Individual well cost data were collected from nearly 300 wells in three major tight gas sand formations: the Cotton Valley sand in East Texas, the Frontier sand in Wyoming, and the Wilcox sand in South Texas. The data were collected and organized by cost category for each formation. After the information was input into a data base, a simple statistical analysis was performed. The statistical analysis identified data discrepancies that were then resolved, and it helped allow conclusions to be drawn regarding drilling and completion costs in these tight sand formations. Results are presented.

Brunsman, B. (Gas Research Inst., Chicago, IL (United States)); Saunders, B. (S.A. Holditch Associates Inc., College Station, TX (United States))

1994-06-06T23:59:59.000Z

84

Triaxial behavior of sand-mica mixtures using genetic programming  

Science Conference Proceedings (OSTI)

This study investigates an application of genetic programming (GP) for modeling of coarse rotund sand-mica mixtures. An empirical model equation is developed by means of GP technique. The experimental database used for GP modeling is based on a laboratory ... Keywords: Genetic programming, Leighton Buzzard Sand, Mica, Modeling, Triaxial testing

Ali Firat Cabalar; Abdulkadir Cevik

2011-08-01T23:59:59.000Z

85

Sand Mountain Electric Coop | Open Energy Information  

Open Energy Info (EERE)

Mountain Electric Coop Mountain Electric Coop Jump to: navigation, search Name Sand Mountain Electric Coop Place Alabama Utility Id 16629 Utility Location Yes Ownership C NERC Location SERC NERC SERC Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Drainage Pumping Station LS - Outdoor Lighting Service Lighting RS - Residential Service Residential Schedule GSA - General Power Service - Part 1 Commercial Schedule GSA - General Power Service - Part 2 Commercial Schedule GSA - General Power Service - Part 3 Commercial Schedule GSB Commercial Schedule GSD Commercial

86

Direct Production of Silicones From Sand  

Science Conference Proceedings (OSTI)

Silicon, in the form of silica and silicates, is the second most abundant element in the earth's crust. However the synthesis of silicones (scheme 1) and almost all organosilicon chemistry is only accessible through elemental silicon. Silicon dioxide (sand or quartz) is converted to chemical-grade elemental silicon in an energy intensive reduction process, a result of the exceptional thermodynamic stability of silica. Then, the silicon is reacted with methyl chloride to give a mixture of methylchlorosilanes catalyzed by cooper containing a variety of tract metals such as tin, zinc etc. The so-called direct process was first discovered at GE in 1940. The methylchlorosilanes are distilled to purify and separate the major reaction components, the most important of which is dimethyldichlorosilane. Polymerization of dimethyldichlorosilane by controlled hydrolysis results in the formation of silicone polymers. Worldwide, the silicones industry produces about 1.3 billion pounds of the basic silicon polymer, polydimethylsiloxane.

Larry N. Lewis; F.J. Schattenmann: J.P. Lemmon

2001-09-30T23:59:59.000Z

87

Acoustic sand detector for fluid flowstreams  

DOE Patents (OSTI)

The particle volume and particle mass production rate of particulate solids entrained in fluid flowstreams such as formation sand or fracture proppant entrained in oil and gas production flowstreams is determined by a system having a metal probe interposed in a flow conduit for transmitting acoustic emissions created by particles impacting the probe to a sensor and signal processing circuit which produces discrete signals related to the impact of each of the particles striking the probe. The volume or mass flow rate of particulates is determined from making an initial particle size distribution and particle energy distribution and comparing the initial energy distribution and/or the initial size distribution with values related to the impact energies of a predetermined number of recorded impacts. The comparison is also used to recalibrate the system to compensate for changes in flow velocity.

Beattie, Alan G. (Corrales, NM); Bohon, W. Mark (Frisco, TX)

1993-01-01T23:59:59.000Z

88

Sand control in horizontal wells in heavy-oil reservoirs  

SciTech Connect

Recent advances in horizontal-well technology has greatly improved the potential for heavy oil recovery. Such recovery may be hampered, however, by sanding problems associated with most heavy-oil reservoirs. These reservoir sands are mostly unconsolidated and may lead to severe productivity-loss problems if produced freely. This paper offers recommendations for sand control in three Canadian heavy-oil reservoirs. Experimental evidence has shown that minimizing the annular space between the casing and the open hole is important, especially in the case of smaller wire space, lower oil viscosity, and thinner pay zone. Several types of wire-wrapped screens and flexible liners were tested for sand control. Only flexible liners reduced sand production to a negligible amount.

Islam, M.R. (Nova Husky Research Corp. (CA)); George, A.E. (Energy, Mines, and Resources (CA))

1991-07-01T23:59:59.000Z

89

Recovery of heavy crude oil or tar sand oil or bitumen from underground formations  

SciTech Connect

This patent describes a method of producing heavy crude oil or tar sand oil or bitumen from an underground formation. The method consists of utilizing or establishing an aqueous fluid communication path within and through the formation between an injection well or conduit and a production well or conduit by introducing into the formation from the injection well or conduit hot water and/or low quality steam at a temperature in the range about 60{sup 0}-130{sup 0}C and at a substantially neutral or alkaline pH to establish or enlarge the aqueous fluid communication path within the formation from the injection well or conduit to the production well or conduit by movement of the introduced hot water or low quality steam through the formation, increasing the temperature of the injected hot water of low quality steam to a temperature in the range about 110{sup 0}-180{sup 0}C while increasing the pH of the injected hot water or low quality steam to a pH of about 10-13 so as to bring about the movement or migration or stripping of the heavy crude oil or tar sand oil or bitumen from the formation substantially into the hot aqueous fluid communication path with the formation and recovering the resulting produced heavy crude oil or tar sand oil or bitumen from the formation as an emulsion containing less than about 30% oil or bitumen from the production well or conduit.

McKay, A.S.

1989-07-11T23:59:59.000Z

90

Determination of critical cracking temperature of oil sands at low temperature conditions.  

E-Print Network (OSTI)

??This research is intended to predict the viscoelastic behavior of oil sand mixesunder low temperature conditions. The oil sand used in this project is a… (more)

Chandika, Charan kumar

2013-01-01T23:59:59.000Z

91

The apparent surface roughness of moving sand transported by wind  

E-Print Network (OSTI)

We present a comprehensive analytical model of aeolian sand transport in saltation. It quantifies the momentum transfer from the wind to the transported sand by providing expressions for the thickness of the saltation layer and the apparent surface roughness. These expressions are for the first time entirely derived from basic physical principles. The model further predicts the sand transport rate (mass flux) and the impact threshold shear velocity. We show that the model predictions are in very good agreement with experiments and numerical state of the art simulations of aeolian saltation.

Thomas Pähtz; Jasper F. Kok; Hans J. Herrmann

2011-11-05T23:59:59.000Z

92

GASIFICATION IN THE CANADIAN OIL SANDS:  

E-Print Network (OSTI)

The Long Lake integrated bitumen and upgrading project, now under construction by OPTI Canada Inc. and Nexen Inc., is the first application of large-scale gasification in Canada. It also represents the first implementation of a gasification project in conjunction with a heavy oil recovery and upgrading project. The Canadian oil sands are a vast petroleum resource that currently produces over one million barrels per day (bpd) using proven mining and in-situ recovery technologies. Production is projected to rise to over two million bpd by the end of the decade. However the large volumes of natural gas normally needed by the bitumen recovery and upgrading facilities are a significant barrier to economic development of the resource. The Long Lake Project uses a unique combination of technologies to provide a solution to the natural gas supply and cost issue. A key component is a gasification facility using the Shell Gasification Process (SGP) which is integrated with the bitumen upgrading to convert the liquid asphaltene by-product stream into hydrogen for the secondary upgrading step and syngas fuel. An Air Liquide air separation unit (ASU) will provide

unknown authors

2004-01-01T23:59:59.000Z

93

Getty mines oil sands in California  

Science Conference Proceedings (OSTI)

A large deposit of oil-laden diatomaceous earth in the McKittrick oil field 40 miles west of Bakersfield, California, has resisted all efforts at production by standard means. Getty Oil Co. is in the pilot phase of a project to recover the Diatomite's oil by an open pit mining operation. It also could have significant implications for other California oil fields, possibly setting the stage for the mining of oil sands in shallow fields like Kern River, S. Belridge, and Lost Hills to maximize oil recovery. A report on the project is summarized. The Diatomite is estimated to have 500 million bbl of oil in reserves, of which 380 million bbl are recoverable. The estimated amount of recoverable oil exceeds the McKittrick field's cumulative production of 240 million bbl. A pilot plant was built to test solvent extraction method of recovering heavy oil. The multistep process involves a series of 6 extractors. The Lurgi retorting plant employs a 2-step heating process to separate hydrocarbons from crushed ore.

Rintoul, B.

1983-11-01T23:59:59.000Z

94

Western Gas Sands Project. Status report  

SciTech Connect

The progress during December, 1977 of the major government sponsored endeavors undertaken to increase gas production from the low permeability gas sands of the western United States is summarized. The USGS is continuing geological and geophysical studies in the four major western basins to better characterize the resource base. Shipping arrangements for the core donated to the USGS by Inexco WASP (a well drilled for possible nuclear explosive stimulation in Wyoming) have been made, and cores for macrofossil and ostracode analysis from the Bowdoin Dome area have been collected. The National Laboratories, funded by DOE, are continuing their work in the area of research and development. The emphasis is on the development of new tools and instrumentation systems, rock mechanics, mathematical modeling and data analysis. Field tests and demonstrations active in the Uinta and Piceance Basins are Gas Producing Enterprises (GPE) Natural Buttes, Wells No. 14, 18, 19, 20, 21, and 22; Mobil Research and Development, Well No. F-31-13G; and Rio Blanco Natural Gas Company, Well No. 498-4-1. Colorado Interstate Gas Company has initiated activity on its project with the installation of equipment, and Mitchell Energy Company's proposal to conduct an MHF test in the Cotton Valley lime gas reservoir in Texas is nearing the contract negotiation stage.

1978-02-01T23:59:59.000Z

95

RFC Sand Creek Development LLC | Open Energy Information  

Open Energy Info (EERE)

RFC Sand Creek Development LLC RFC Sand Creek Development LLC Jump to: navigation, search Name RFC Sand Creek Development LLC Place Aurora, Colorado Zip 80014 Product Subsidiary of Republic Financial Corporation set up to invest in Sand Creek Energy LLC, a planned gas to liquid facility. Coordinates 39.325162°, -79.54975° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.325162,"lon":-79.54975,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

96

Sand Ridges and Dunes in the Calumet Region  

NLE Websites -- All DOE Office Websites (Extended Search)

when the U. S. Steel corporation purchased 8000 acres of sand dunes and swamps for its mills and a new city, Gary, you can still see ridge after ridge paralleling the lake shore...

97

Sand Dunes Hot Spring Aquaculture Low Temperature Geothermal Facility |  

Open Energy Info (EERE)

Sand Dunes Hot Spring Aquaculture Low Temperature Geothermal Facility Sand Dunes Hot Spring Aquaculture Low Temperature Geothermal Facility Jump to: navigation, search Name Sand Dunes Hot Spring Aquaculture Low Temperature Geothermal Facility Facility Sand Dunes Hot Spring Sector Geothermal energy Type Aquaculture Location Hooper, Colorado Coordinates 37.7427775°, -105.8752987° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

98

CONTRACTOR REPORT SAND96-2555 UC-1243 Unlimited Release  

NLE Websites -- All DOE Office Websites (Extended Search)

CONTRACTOR REPORT SAND96-2555 UC-1243 Unlimited Release A Study of Productionlnjection Data from Slim Holes and Large-Diameter Wells at the Takigami Geothermal Field, Kyushu,...

99

The effects of psammophilous plants on sand dune dynamics  

E-Print Network (OSTI)

Psammophilous plants are special plants that flourish in sand moving environments. There are two main mechanisms by which the wind affects these plants: (i) sand drift exposes roots and covers branches--the exposed roots turn into new plants and the covered branches turn into new roots; both mechanisms result in an enhanced growth rate of the psammophilous plant cover of the dunes; (ii) strong winds, often associated with sand movement, tear branches and seed them in nearby locations, resulting in new plants and an enhanced growth rate of the psammophilous plant cover of the dunes. Despite their important role in dune dynamics, to our knowledge, psammophilous plants have never been incorporated into mathematical models of sand dunes. Here, we attempt to model the effects of these plants on sand dune dynamics. We construct a set of three ordinary differential equations for the fractions of surface cover of regular vegetation, biogenic soil crust and psammophilous plants. The latter reach their optimal growth under (i) specific sand drift or (ii) specific wind power. We show that psammophilous plants enrich the sand dune dynamics. Depending on the climatological conditions, it is possible to obtain one, two, or three steady dune states. The activity of the dunes can be associated with the surface cover--bare dunes are active, and dunes with significant cover of vegetation, biogenic soil crust, or psammophilous plants are fixed. Our model shows that under suitable precipitation rates and wind power, the dynamics of the different cover types is in accordance with the common view that dunes are initially stabilized by psammophilous plants that reduce sand activity, thus enhancing the growth of regular vegetation that eventually dominates the cover of the dunes and determines their activity.

Golan Bel; Yosef Ashkenazy

2013-08-30T23:59:59.000Z

100

Western tight gas sands advanced logging workshop proceedings  

SciTech Connect

An advanced logging research program is one major aspect of the Western Tight Sands Program. Purpose of this workshop is to help BETC define critical logging needs for tight gas sands and to allow free interchange of ideas on all aspects of the current logging research program. Sixteen papers and abstracts are included together with discussions. Separate abstracts have been prepared for the 12 papers. (DLC)

Jennings, J B; Carroll, Jr, H B [eds.

1982-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Western gas sands project status report  

SciTech Connect

The Western Gas Sands Project Plan, Project Implementation Plans and Project Plan Document FY 78 are in various stages of preparation. Information gathering by U.S. Geological Survey (USGS) of the initial data base for many of the project activities is nearing completion. Some base maps are complete and field investigations in the principal areas of interest are being conducted. Research and development by Energy Research Centers and National Laboratories were directed toward new tools and instrumentation systems, rock mechanics experiments, mathematical modeling, and data analysis. The Uinta Basin in Utah and Piceance Basin in Colorado have ongoing massive hydraulic fracture (MHF) experiments in the Upper Cretaceous tight gas formations. These are: CER Corporation, MHF 3; Gas Producing Enterprises, Natural Buttes No. 14, 18, 19, 20; Mobil Oil, F-31-13G; and Rio Blanco Natural Gas, 498-4-1. Colorado Interstate Gas Company has been awarded a contract to determine if productivity in low permeability reservoirs can be improved by reducing the interstitialwater saturation. They will be using two wells, the Sprague No. 1 and Miller No. 1, completed in the Dakota J formation in the Wattenberg Field in north central Colorado. All of the massive hydraulic fracture wells, with the exception of the Pacific Transmission well, have been fractured as planned. The Mobil and GPE No. 14, 18, and 20 wells show significant improvement as compared to original flow rates. The Mobil well is being tested for additional MHF treatments. Sandia Laboratories is continuing their research program in hydraulic fracturing at DOE's Nevada Test Site (NTS).

1977-11-01T23:59:59.000Z

102

The extraction of bitumen from western tar sands. Annual report, July 1990--July 1991  

Science Conference Proceedings (OSTI)

Contents of this report include the following: executive summary; characterization of the native bitumen from the Whiterocks oil sand deposit; influence of carboxylic acid content on bitumen viscosity; water based oil sand separation technology; extraction of bitumen from western oil sands by an energy-efficient thermal method; large- diameter fluidized bed reactor studies; rotary kiln pyrolysis of oil sand; catalytic upgrading of bitumen and bitumen derived liquids; ebullieted bed hydrotreating and hydrocracking; super critical fluid extraction; bitumen upgrading; 232 references; Appendix A--Whiterocks tar sand deposit bibliography; Appendix B--Asphalt Ridge tar sand deposit bibliography; and Appendix C--University of Utah tar sands bibliography.

Oblad, A.G.; Bunger, J.W.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1992-04-01T23:59:59.000Z

103

DOE/EA-1584: Final Environmental Assessment for Sand Point Wind Installation Project, Sand Point, Alaska (September 2009)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sand Point Wind Installation Project Sand Point, Alaska DOE/EA -1584 U.S. Department of Energy Golden Field Office 1617 Cole Boulevard Golden, Colorado 80401-3305 September 2009 TABLE OF CONTENTS Page 1.0 INTRODUCTION .............................................................................................................. 1 1.1 NATIONAL ENVIRONMENTAL POLICY ACT AND RELATED PROCEDURES....................................................................................................... 1 1.2 BACKGROUND .................................................................................................... 1 1.3 PURPOSE AND NEED.......................................................................................... 2 1.4 PUBLIC SCOPING AND CONSULTATION.......................................................

104

Method of tagging sand with ruthenium-103 and the resultant product  

DOE Patents (OSTI)

A procedure for tagging sand with a radioisotope for use in the study of sediment transport involves the precipitation of a metal radioisotope in the form of an iodide directly on the sand, followed by heating the sand to a temperature sufficient to effect a phase transformation of the sand and a decomposition of the metal iodide, leaving the metal firmly attached to the sand.

Case, Forrest N. (Oak Ridge, TN); McFarland, Clyde E. (Knoxville, TN)

1976-01-01T23:59:59.000Z

105

RADIO RANGING DEVICE  

DOE Patents (OSTI)

A radio ranging device is described. It utilizes a super regenerative detector-oscillator in which echoes of transmitted pulses are received in proper phase to reduce noise energy at a selected range and also at multiples of the selected range.

Nieset, R.T.

1961-05-16T23:59:59.000Z

106

ERDC/ELTR-12-10 Army Range Technology Program  

E-Print Network (OSTI)

. .........................................................................34 Figure 41. Sticky trap with sand captured and sealed for transport mixer and allowed to thoroughly distribute through the sand. The sand was then placed back in the catch

US Army Corps of Engineers

107

Method for manufacturing a well production and sand screen assembly  

SciTech Connect

A method for forming and assembling a well production and sand screen assembly in a well having a screen therein forming an outer annulus and a wash pipe internally of the screen forming an inner annulus comprising further (A) mounting a high pressure fluid pump means and a valve means on each wash pipe, inner annulus, and outer annulus, and (B) connecting the valve means in fluid communication with the high pressure fluid pump means for controlling the ingress and egress of the high pressure fluids and removed formation material for forming a sand pack in the well and simultaneously for applying and maintaining a positive fluid pressure against the overburden during work in the well for preventing cave-ins and sloughing of the unconsolidated formation well walls until the sand pack is formed.

Widmyer, R.H.

1982-10-12T23:59:59.000Z

108

Technology assessment: environmental, health, and safety impacts associated with oil recovery from US tar-sand deposits  

SciTech Connect

The tar-sand resources of the US have the potential to yield as much as 36 billion barrels (bbls) of oil. The tar-sand petroleum-extraction technologies now being considered for commercialization in the United States include both surface (above ground) systems and in situ (underground) procedures. The surface systems currently receiving the most attention include: (1) thermal decomposition processes (retorting); (2) suspension methods (solvent extraction); and (3) washing techniques (water separation). Underground bitumen extraction techniques now being field tested are: (1) in situ combustion; and (2) in situ steam-injection procedures. At this time, any commercial tar-sand facility in the US will have to comply with at least 7 major federal regulations in addition to state regulations; building, electrical, and fire codes; and petroleum-industry construction standards. Pollution-control methods needed by tar-sand technologies to comply with regulatory standards and to protect air, land, and water quality will probably be similar to those already proposed for commercial oil-shale systems. The costs of these systems could range from about $1.20 to $2.45 per barrel of oil produced. Estimates of potential pollution-emisson levels affecting land, air, and water were calculated from available data related to current surface and in situ tar-sand field experiments in the US. These data were then extrapolated to determine pollutant levels expected from conceptual commercial surface and in situ facilities producing 20,000 bbl/d. The likelihood-of-occurrence of these impacts was then assessed. Experience from other industries, including information concerning health and ecosystem damage from air pollutants, measurements of ground-water transport of organic pollutants, and the effectiveness of environmental-control technologies was used to make this assessment.

Daniels, J.I.; Anspaugh, L.R.; Ricker, Y.E.

1981-10-13T23:59:59.000Z

109

Long range dependence  

Science Conference Proceedings (OSTI)

The notion of long range dependence is discussed from a variety of points of view, and a new approach is suggested. A number of related topics is also discussed, including connections with non-stationary processes, with ergodic theory, self-similar processes ... Keywords: large deviations, long range dependence, rare events

Gennady Samorodnitsky

2007-01-01T23:59:59.000Z

110

Enhancing permeability in oil shale and applications to tar sands  

SciTech Connect

Explosive fracturing and rubblization are used to enhance oil shale permeability. Blasting strategy and results are discussed, in particular the Geokinetics blasting. The field data desired are listed. Comments are offered on the extension of the blasting techniques to tar sands. (DLC)

Schamaun, J.T.

1980-01-01T23:59:59.000Z

111

Mechanism of acoustic emissions from booming sand dunes  

E-Print Network (OSTI)

The classical elastic mechanics shows that the fundamental frequency of a sand grain chain is similar to the typical frequency of acoustic emission generated by the booming dunes. The "song of dunes" is therefore considered to originate from the resonance of grain chains occurring within a solid layer only several centimeters thick.

Zhen-Ting Wang

2013-05-10T23:59:59.000Z

112

CO{sub 2}/sand fracturing in low permeability reservoirs  

Science Conference Proceedings (OSTI)

The objectives of this study are: to demonstrate the effectiveness of a non-damaging liquid, carbon dioxide (CO{sub 2}) in creating sand-propped hydraulic fractures in ``tight`` gas bearing formations within the Appalachian Basin; and to compare and rank the gas production responses from wells treated with liquid CO{sub 2} with other types of treatments (shooting, water based, nitrogen, etc.). The preliminary results are encouraging, and although only a few months of production is available, the rate of gas production from the CO{sub 2} treated candidate wells is greater than that from the control wells. The CO{sub 2}/sand fracs appear to be 56 percent better than the nitrogen fracs in Pike County. In addition, the CO{sub 2}/sand fracs are 4.8 times better than conventional shot wells in the Pike County study area. It should be recognized that these results are from a very limited data set and overall conclusions may change as more control wells are added to the analysis. From a stimulation process achievement viewpoint, the maximum amount of sand pumped is 46,000 pounds at an average concentration of 3.1 pound per gallon. It should be pointed out that additional foam and nitrogen stimulations have recently been performed by the operator in the Pike County area, and subsequent discussions in the future will include additional control wells to the baseline data sets.

Mazza, R.L.; Gehr, J.B.

1993-12-31T23:59:59.000Z

113

Nitrate-Cancrinite Precipitation on Quartz Sand in Simulated Hanford  

E-Print Network (OSTI)

Nitrate-Cancrinite Precipitation on Quartz Sand in Simulated Hanford Tank Solutions B A R R Y R . B minerals at the U.S. Department of Energy's Hanford site in Washington. Nitrate-cancrinite began's (DOE) Hanford Site in southeast Washington since the late 1950s (1). To predict the fate

Illinois at Chicago, University of

114

SAND2006-1982J Solid-State Environmentally Safe  

E-Print Network (OSTI)

battery packs in parallel.The commercial target cost is expected to open at $50 per 1.5-volt cellSAND2006-1982J #12;Solid-State Environmentally Safe Battery for Replacing Lithium Batteries 1 Entry with High Power Battery Systems Company 5 Silkin Street, Apt. 40 Sarov, Nizhny Novgorod Russia

115

Western Gas Sands Project. Quarterly basin activities report  

SciTech Connect

A summation is presented of the coring program site identification, and drilling and testing activity in the four primary study areas of the Western Gas Sands Project (WGSP). Pertinent information for January, February, and March, 1978 is included for each study area. The areas are the Northern Great Plains Province, the Greater Green River Basin, the Piceance Basin, and the Uinta Basin.

1978-04-01T23:59:59.000Z

116

Paleo-Storminess in the Southern Lake Michigan Basin, as Recorded by Eolian Sand Downwind of Dunes.  

E-Print Network (OSTI)

??Eolian sand deposited in lakes downwind of coastal sand dunes record a history of paleoclimatic fluctuations. Studies from embayed lakes along the east-central coast of… (more)

Hanes, Barbara E.

2010-01-01T23:59:59.000Z

117

The extraction of bitumen from western oil sands. Final report, July 1989--September 1993  

Science Conference Proceedings (OSTI)

Research and development of surface extraction and upgrading processes of western tar sands are described. Research areas included modified hot water, fluidized bed, and rotary kiln pyrolysis of tar sands for extraction of bitumen. Bitumen upgrading included solvent extraction of bitumen, and catalytic hydrotreating of bitumen. Characterization of Utah tar sand deposits is also included.

Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Fletcher, J.V.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1994-03-01T23:59:59.000Z

118

Examination of pulverized waste recycled glass as filter media in slow sand filtration. Final report  

SciTech Connect

The purpose of this study was to investigate the pulverization of waste recycled glass to produce glass sand for slow sand filters. Pulverization experiments were performed using a fail mill pulverizer. The glass sand product from the pulverizer meets the size distribution requirements of ASTM-C-33 without size distribution adjustment. The size distribution must be adjusted to meet the grain size distribution requirements of the Ten States Standards and the USEPA for filter media used in slow sand filters. Pulverized glass that meet slow sand filter media specifications is an effective alternative to silica sand as a filter media for slow sand filtration. Three pilot plant slow sand filters with glass sand filter media were compared to a fourth filter containing silica sand filter media. Over an 8 month period of continuous operation, the performance of the glass sand filter media was as good or better than the silica sands, with removals of 56% to 96% for turbidity; 99.78% to 100.0% for coliform bacteria; 99.995% to 99.997% for giardia cysts; 99.92% and 99.97% for cryptosporidium oocysts. Based on a cost-benefit analysis, converting waste glass into filter media may be economically advantageous for recycling facilities.

Piccirillo, J.B.; Letterman, R.D.

1997-10-01T23:59:59.000Z

119

RADIO RANGING DEVICE  

DOE Patents (OSTI)

A description is given of a super-regenerative oscillator ranging device provided with radiating and receiving means and being capable of indicating the occurrence of that distance between itself and a reflecting object which so phases the received echo of energy of a preceding emitted oscillation that the intervals between oscillations become uniform.

Bogle, R.W.

1960-11-22T23:59:59.000Z

120

High dynamic range imaging  

Science Conference Proceedings (OSTI)

Current display devices can display only a limited range of contrast and colors, which is one of the main reasons that most image acquisition, processing, and display techniques use no more than eight bits per color channel. This course outlines recent ...

Paul Debevec; Erik Reinhard; Greg Ward; Sumanta Pattanaik

2004-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

SAND97-8490 UC-404 Unlimited Release  

Office of Scientific and Technical Information (OSTI)

SAND97-8490 UC-404 SAND97-8490 UC-404 Unlimited Release Printed March 1997 J Mechanical Properties and Energy Absorption Characteristics of a Polyurethane Foam S. H. Goods, C. L. Neuschwanger, C. Henderson, D. M. Skala DISCLAIMER This report was prepared as a n account of work sponsored by a n agenq of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, make any warrantyy express or impIied, or assumes any legal liabili- ty or responsibility for the accuracy, completeness, or usefulness of any information, appa- ratus, product, or process disdased, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necrsariiy constitute or

122

Shredded tires and rubber-sand as lightweight backfill  

Science Conference Proceedings (OSTI)

The growing interest in utilizing waste materials in civil engineering applications has opened the possibility of constructing reinforced soil structures with unconventional backfills. Scrap tires are a high-profile waste material for which several uses have been studied, including the use of shredded tires as backfill. A triaxial testing program was conducted to investigate the stress-strain relationship and strength of tire chips and a mixture of sand and tire chips. The test results and additional information from the literature were used in the numerical modeling of wall backfills, both unreinforced and reinforced with geosynthetics. The numerical modeling results suggest tire shreds, particularly when mixed with sand, may be effectively used as a backfill.

Lee, J.H.; Salgado, R.; Lovell, C.W. [Purdue Univ., West Lafayette, IN (United States). School of Civil Engineering; Bernal, A. [GeoHidra, Caracas (Venezuela)

1999-02-01T23:59:59.000Z

123

White Sands, New Mexico: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Sands, New Mexico: Energy Resources Sands, New Mexico: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 32.38319°, -106.481499° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":32.38319,"lon":-106.481499,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

124

Method for diverting a gaseous sand-consolidating fluid  

SciTech Connect

An unconsolidated gas-producing sand in which the permeability is layered and the productivity can be impaired by liquid blocking can be consolidated by wetting the rock surfaces with a limited amount of water, injecting a smoke which selectively reduces the permeability of the most permeable layers by depositing on their faces unconsolidated masses of substantially inert solid particles and injecting a gaseous silicon polyhalide to convert a significant proportion of the rock surface-wettingwater to a grain bonding silica gel.

Davies, D. R.; Richardson, E. A.

1980-12-30T23:59:59.000Z

125

Project Drum Inlet: explosive excavation in saturated sand  

SciTech Connect

Seasonal storms during February of 1971 completely closed the Drum Inlet navigation channel through the Outer Banks off the North Carolina coast. This channel is highly useful to commercial and sport fishing industries in the Carteret County vicinity of North Carolina, and is vital to maintenance of the ecological balance in the inland Core Sound waters. To reopen Drum Inlet, an alignment about 2.1 miles south of the original location was selected. A contract dredge excavated a channel from the inland Core Sound waterway to and part way through the Outer Banks. The final 385-ft-long section of sand separating the Core Sound from the Atlantic Ocean was excavated with large explosive charges, This report describes the explosive excavation of that portion of the channel. Twenty-two separate canisters, each containing 1 ton of aluminized ammonium-nitrate slurry blasting agent, were emplaced in two rows. All charges were detonated simultaneously at 1327 hours, 23 Decembcr 1971. The detonation successfully removed the sand barrier, forming a continuous channel over 80 ft in width. This channel subsequently washed out to a width of about 1000 ft and was used:is an access route to the Raleigh Bay fishing grounds. The Drum Inlet project demonstrated the practicality of explosive channel excavation in saturated sand under the special conditions encountered at this site. (auth)

Snell, C.M.; Gillespie, R.H.

1973-10-01T23:59:59.000Z

126

Improved core recovery in laminated sand and shale sequences  

SciTech Connect

Coring and core analysis are essential to the exploration, development, and production phases of the oil and gas industry. Large-diameter (4-in. (10-cm)) core provides engineers and geologists with direct means to measure physical properties of reservoir rocks at both the microscopic and macroscopic levels. This information provides engineers with clues to improve their understanding of the reservoir and prediction of its performance. If stored properly, core may assist in development of the reservoir many years after the well is drilled. In microlaminated reservoirs, laboratory core analysis is very important because of inherent limitations in wireline log resolution. In these cases, petrophysical information, such as saturation, porosity, and net feet of pay, cannot be calculated from wireline data. Instead, these data must be measured directly from core plugs in the laboratory. Historically, core recovery in these types of reservoirs has not been good (Fig. 1A) using methods designed for firmly consolidated formations. These methods did not achieve satisfactory recovery in unconsolidated sand interbedded with hard shale stringers for two reasons: unconsolidated sand was eroded by mechanical or hydraulic means and shale ''jammed'' in the core barrel, thereby preventing more core from entering. Changes in coring strategies and equipment have nearly eliminated recovery problems in unconsolidated sand while reducing jams in shale (Fig. 1B). This paper discusses several of these changes and presents ideas for further improvements.

Bradburn, F.R.; Cheatham, C.A. (Shell Offshore Inc. (US))

1988-12-01T23:59:59.000Z

127

File:OilSands.pdf | Open Energy Information  

Open Energy Info (EERE)

OilSands.pdf OilSands.pdf Jump to: navigation, search File File history File usage File:OilSands.pdf Size of this preview: 463 × 599 pixels. Other resolution: 464 × 600 pixels. Go to page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 Go! next page → next page → Full resolution ‎(1,275 × 1,650 pixels, file size: 1.69 MB, MIME type: application/pdf, 85 pages) File history Click on a date/time to view the file as it appeared at that time. Date/Time Thumbnail Dimensions User Comment current 14:24, 14 February 2012 Thumbnail for version as of 14:24, 14 February 2012 1,275 × 1,650, 85 pages (1.69 MB) Graham7781 (Talk | contribs)

128

RANGE DESIGN CRITERIA  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

RANGE DESIGN CRITERIA RANGE DESIGN CRITERIA U.S. DEPARTMENT OF ENERGY Office of Health, Safety and Security AVAILABLE ONLINE AT: INITIATED BY: http://www.hss.energy.gov Office of Health, Safety and Security Notices This document is intended for the exclusive use of elements of the Department of Energy (DOE), to include the National Nuclear Security Administration, their contractors, and other government agencies/individuals authorized to use DOE facilities. DOE disclaims any and all liability for personal injury or property damage due to use of this document in any context by any organization, group, or individual, other than during official government activities. Local DOE management is responsible for the proper execution of firearms-related programs for

129

Neutron range spectrometer  

DOE Patents (OSTI)

A neutron range spectrometer and method for determining the neutron energy spectrum of a neutron emitting source are disclosed. Neutrons from the source are colliminated along a collimation axis and a position sensitive neutron counter is disposed in the path of the collimated neutron beam. The counter determines positions along the collimation axis of interactions between the neutrons in the neutron beam and a neutron-absorbing material in the counter. From the interaction positions, a computer analyzes the data and determines the neutron energy spectrum of the neutron beam. The counter is preferably shielded and a suitable neutron-absorbing material is He-3. 1 fig.

Manglos, S.H.

1988-03-10T23:59:59.000Z

130

National Metal Casting Research Institute final report. Volume 1, Sand reclamation  

Science Conference Proceedings (OSTI)

A mobile thermal foundry sand reclamation unit was designed and constructed. This unit consisted of thermal and mechanical sand reclamation equipment installed on the bed of a 50 foot low-boy trailer. It was transported to a number of Midwest foundries for on-site demonstration of the sand reclamation process. This allowed participating foundries to have their own refuse sand (10-100 tons) processed and then reused in production for evaluation. The purpose for building the unit was to demonstrate to foundries through ``hands on`` experience that refuse sands can be reclaimed and successfully reused particularly in regard to product quality. Most of the participating foundries indicated a high level of satisfaction with the reclaimed sand. Laboratory testing of samples of the used sand, before and after processing by the demonstration unit, verified the usability of the reclaimed sand. One of the foundries participating was a brass foundry, the sand from this foundry contained lead and is classified as a hazardous material. After reclamation the sand was no longer hazardous and could also be reused in the foundry.

Vondra, L.F.; Burningham, J.S. [University of Northern Iowa, Cedar Falls, IA (United States). Dept. of Industrial Technology

1995-08-01T23:59:59.000Z

131

The extraction of bitumen from western oil sands: Volume 2. Final report  

Science Conference Proceedings (OSTI)

The program is composed of 20 projects, of which 17 are laboratory bench or laboratory pilot scale processes or computer process simulations that are performed in existing facilities on the University of Utah campus in north-east Salt Lake City. These tasks are: (1) coupled fluidized-bed bitumen recovery and coked sand combustion; (2) water-based recovery of bitumen; (3) oil sand pyrolysis in a continuous rotary kiln reactor; (4) oil sand pyrolysis in a large diameter fluidized bed reactor; (5) oil sand pyrolysis in a small diameter fluidized bed reactor; (6) combustion of spent sand in a transport reactor; (7) recovery and upgrading of oil sand bitumen using solvent extraction methods; (8) fixed-bed hydrotreating of Uinta Basin bitumens and bitumen-derived hydrocarbon liquids; (9) ebullieted bed hydrotreating of bitumen and bitumen derived liquids; (10) bitumen upgrading by hydropyrolysis; (11) evaluation of Utah`s major oil sand deposits for the production of asphalt, high-energy jet fuels and other specialty products; (12) characterization of the bitumens and reservoir rocks from the Uinta Basin oil sand deposits; (13) bitumen upgrading pilot plant recommendations; (14) liquid-solid separation and fine tailings thickening; (15) in-situ production of heavy oil from Uinta Basin oil sand deposits; (16) oil sand research and development group analytical facility; and (17) process economics. This volume contains reports on nine of these projects, references, and a bibliography. 351 refs., 192 figs., 65 tabs.

Oblad, A.G.; Dahlstrom, D.A.; Deo, M.D.; Fletcher, J.V.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1997-11-26T23:59:59.000Z

132

Range imaging laser radar  

SciTech Connect

A laser source is operated continuously and modulated periodically (typicy sinusoidally). A receiver imposes another periodic modulation on the received optical signal, the modulated signal being detected by an array of detectors of the integrating type. Range to the target determined by measuring the phase shift of the intensity modulation on the received optical beam relative to a reference. The receiver comprises a photoemitter for converting the reflected, periodically modulated, return beam to an accordingly modulated electron stream. The electron stream is modulated by a local demodulation signal source and subsequently converted back to a photon stream by a detector. A charge coupled device (CCD) array then averages and samples the photon stream to provide an electrical signal in accordance with the photon stream.

Scott, Marion W. (Albuquerque, NM)

1990-01-01T23:59:59.000Z

133

Lunar Laser Ranging Science  

E-Print Network (OSTI)

Analysis of Lunar Laser Ranging (LLR) data provides science results: gravitational physics and ephemeris information from the orbit, lunar science from rotation and solid-body tides, and Earth science. Sensitive tests of gravitational physics include the Equivalence Principle, limits on the time variation of the gravitational constant G, and geodetic precession. The equivalence principle test is used for an accurate determination of the parametrized post-Newtonian (PPN) parameter \\beta. Lunar ephemerides are a product of the LLR analysis used by current and future spacecraft missions. The analysis is sensitive to astronomical parameters such as orbit, masses and obliquity. The dissipation-caused semimajor axis rate is 37.9 mm/yr and the associated acceleration in orbital longitude is -25.7 ''/cent^2, dominated by tides on Earth with a 1% lunar contribution. Lunar rotational variation has sensitivity to interior structure, physical properties, and energy dissipation. The second-degree lunar Love numbers are detected; k_2 has an accuracy of 11%. Lunar tidal dissipation is strong and its Q has a weak dependence on tidal frequency. A fluid core of about 20% the Moon's radius is indicated by the dissipation data. Evidence for the oblateness of the lunar fluid-core/solid-mantle boundary is getting stronger. This would be independent evidence for a fluid lunar core. Moon-centered coordinates of four retroreflectors are determined. Station positions and motion, Earth rotation variations, nutation, and precession are determined from analyses. Extending the data span and improving range accuracy will yield improved and new scientific results. Adding either new retroreflectors or precise active transponders on the Moon would improve the accuracy of the science results.

James G. Williams; Dale H. Boggs; Slava G. Turyshev; J. Todd Ratcliff

2004-11-18T23:59:59.000Z

134

Non-Darcy flow analysis through tight sand formations  

SciTech Connect

An experimental setup was designed and constructed to measure the flow parameters through tight sand porous media. The two kinds of coreholders being used are Hassler-type and one in which the core sample is encapsulated in layers of epoxy resin and metal alloy. A gas flow measuring system was also developed for accurately measuring very low gas flow rates. Using Darcy's Law as a tool for analysis of the experimental data, we obtained that the gas permeability of the SFE No. 3 (Staged Field Experiment No. 3) core samples is a linear function of reciprocal mean pressure, and decreases with overburden pressure. The water permeability is also decreased with overburden pressure and is about 6 times smaller than gas permeability for the samples that we have tested. No significant hysteresis effect was obtained for dry gas permeability after several two phase flow runs. We successfully tested our encapsulated coreholder and measured gas flow rate through a tight sand core sample at different pressure drops. The results showed that the experimental runs using Hassler-type coreholder at overburden pressures higher than 2000 psig will probably give us the reliable experimental data. The experimental data obtained from the two different types of tight sandstones were analyzed using the Non-Darcy flow equation. The results showed the importance and reliability of the Non-Darcy formulation for describing the flow behavior under different overburden and system pressures. Non-Darcy's velocity for both gas and liquid phase were incorporated into an existing FORTRAN code for simulation of the tight gas reservoirs. The modified program was tested to compare the initial production data of SFE No. 2 well. Our simulation showed in the case of local turbulence and non-uniformities in the tight sand formation, the value of [beta] increases and Non-Darcy effect becomes important.

Wang, Ching-Huei.

1992-01-01T23:59:59.000Z

135

Completion methods in thick, multilayered tight gas sands  

E-Print Network (OSTI)

Tight gas sands, coal-bed methane, and gas shales are commonly called unconventional reservoirs. Tight gas sands (TGS) are often described as formations with an expected average permeability of 0.1mD or less. Gas production rates from TGS reservoirs are usually low due to poor permeability. As such, state-of-the-art technology must be used to economically develop the resource. TGS formations need to be hydraulically fractured in order to enhance the gas production rates. A majority of these reservoirs can be described as thick, multilayered gas systems. Many reservoirs are hundreds of feet thick and some are thousands of feet thick. The technology used to complete and stimulate thick, tight gas reservoirs is quite complex. It is often difficult to determine the optimum completion and stimulating techniques in thick reservoirs. The optimum methods are functions of many parameters, such as depth, pressure, temperature, in-situ stress and the number of layers. In multilayered reservoirs, it is important to include several sand layers in a single completion. The petroleum literature contains information on the various diversion techniques involved in the completion of these multilayered reservoirs. In this research, we have deduced and evaluated eight possible techniques that have been used in the oil and gas industry to divert multilayered fracture treatments in layered reservoirs. We have developed decision charts, economic analyses and computer programs that will assist completion engineers in determining which of the diversion methods are feasible for a given well stimulation. Our computer programs have been tested using case histories from the petroleum literature with results expressed in this thesis. A limited entry design program has also being developed from this research to calculate the fluid distribution into different layers when fracture treating multilayered tight gas reservoirs using the limited entry technique. The research is aimed at providing decision tools which will eventually be input into an expert advisor for well completions in tight gas reservoirs worldwide.

Ogueri, Obinna Stavely

2007-12-01T23:59:59.000Z

136

Production process for glass sand from the quartz waste from the beneficiation of kingiseppsk phosphorites  

SciTech Connect

This paper presents a process developed for the production of molding sand from the quartz waste which makes it possible to simplify the system for obtaining glass sand. According to this system, the main operation in the removal of most of the residual phosphate shell and alkaline earth metal oxides from the quartz waste is foam separation, using the residual concentration of reagents in the pulp (tallow and kerosene). After the subsequent washing and hydraulic classification, the sands meet the requirements set for molding sands grade Ob2K. The characteristics of the original flotation tailings and molding sand are presented. The mineralogical analysis of the molding sand showed that the iron-containing impurities are grains of glauconite, films of iron oxide on the surface of the grains, grains of ferrous-dolomite cement, and iron from the apparatus.

Ershov, V.I.; Lezhnev, Y.P.; Novofastovskaya, E.M.; Rants, G.F.; Shalamova, V.G.; Sinyakova, E.I.; Sokolova, E.I.

1985-12-01T23:59:59.000Z

137

Costs Models in Design and Manufacturing of Sand Casting Products  

E-Print Network (OSTI)

In the early phases of the product life cycle, the costs controls became a major decision tool in the competitiveness of the companies due to the world competition. After defining the problems related to this control difficulties, we will present an approach using a concept of cost entity related to the design and realization activities of the product. We will try to apply this approach to the fields of the sand casting foundry. This work will highlight the enterprise modelling difficulties (limits of a global cost modelling) and some specifics limitations of the tool used for this development. Finally we will discuss on the limits of a generic approach.

Perry, Nicolas; Bernard, Alain

2010-01-01T23:59:59.000Z

138

Costs Models in Design and Manufacturing of Sand Casting Products  

E-Print Network (OSTI)

In the early phases of the product life cycle, the costs controls became a major decision tool in the competitiveness of the companies due to the world competition. After defining the problems related to this control difficulties, we will present an approach using a concept of cost entity related to the design and realization activities of the product. We will try to apply this approach to the fields of the sand casting foundry. This work will highlight the enterprise modelling difficulties (limits of a global cost modelling) and some specifics limitations of the tool used for this development. Finally we will discuss on the limits of a generic approach.

Nicolas Perry; Magali Mauchand; Alain Bernard

2010-11-26T23:59:59.000Z

139

Production from multiple zones of a tar sands formation  

DOE Patents (OSTI)

A method for treating a tar sands formation includes providing heat to at least part of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat is allowed to transfer from the heaters to at least a portion of the formation. Fluids are produced from the formation through at least one production well that is located in at least two zones in the formation. The first zone has an initial permeability of at least 1 darcy. The second zone has an initial of at most 0.1 darcy. The two zones are separated by a substantially impermeable barrier.

Karanikas, John Michael; Vinegar, Harold J

2013-02-26T23:59:59.000Z

140

Systems and methods for producing hydrocarbons from tar sands formations  

DOE Patents (OSTI)

A system for treating a tar sands formation is disclosed. A plurality of heaters are located in the formation. The heaters include at least partially horizontal heating sections at least partially in a hydrocarbon layer of the formation. The heating sections are at least partially arranged in a pattern in the hydrocarbon layer. The heaters are configured to provide heat to the hydrocarbon layer. The provided heat creates a plurality of drainage paths for mobilized fluids. At least two of the drainage paths converge. A production well is located to collect and produce mobilized fluids from at least one of the converged drainage paths in the hydrocarbon layer.

Li, Ruijian (Katy, TX); Karanikas, John Michael (Houston, TX)

2009-07-21T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Pore-scale mechanisms of gas flow in tight sand reservoirs  

E-Print Network (OSTI)

include tight gas sands, gas shales, and coal-bed methane.Figure 3. Although the gas-shale production grows at a

Silin, D.

2011-01-01T23:59:59.000Z

142

Non-Incineration Treatment to Reduce Benzene and VOC Emissions from Green Sand Molding Systems  

SciTech Connect

Final report describing laboratory, pilot scale and production scale evaluation of advanced oxidation systems for emissions and cost reduction in metal casting green sand systems.

Fred S. Cannon; Robert C. Voigt

2002-06-28T23:59:59.000Z

143

Development of Optimal Energy Infrastructures for the Oil Sands Industry in a CO?-constrained World.  

E-Print Network (OSTI)

??Western Canadian bitumen is becoming a predominant source of energy for North American markets. The bitumen extraction and upgrading processes in the oil sands industry… (more)

Ordorica Garcia, Jesus Guillermo

2007-01-01T23:59:59.000Z

144

Adsorption of Single-ring Model Naphthenic Acid from Oil Sands ...  

Science Conference Proceedings (OSTI)

Presentation Title, Adsorption of Single-ring Model Naphthenic Acid from Oil Sands Tailings Pond Water Using Petroleum Coke-derived Activated Carbon.

145

An investigation of the combustion of oil sand derived bitumen-in-water emulsions.  

E-Print Network (OSTI)

?? Dwindling conventional oil resources has caused exploration efforts to focus elsewhere. Bitumen from oil sands has emerged as one of the primary unconventional oil… (more)

Kennelly, Timothy Robert

2009-01-01T23:59:59.000Z

146

O-1: Using of Spent Moulding Sands for Production of Burned ...  

Science Conference Proceedings (OSTI)

The measurements of exhaust gases emissions performed during burning the products containing spent moulding sands as well as during the normal ...

147

I-8: Research on the Influence of Moulding Sand with Furan Resin ...  

Science Conference Proceedings (OSTI)

Presentation Title, I-8: Research on the Influence of Moulding Sand with Furan Resin ... Study of Different metallurgical Waste for Preparation of Glass-Ceramics.

148

Meso-Scale Simulations to Examine the Role of Sand Paper Grit on ...  

Science Conference Proceedings (OSTI)

The surface between the platen and LX-10 sample includes a layer of sand particulates to .... Shock-Induced Phase Transformations in Ce-Al Metallic Glass.

149

Development Of Reclamation Substrates For Alberta Oil Sands Using Mature Fine Tailings And Coke.  

E-Print Network (OSTI)

??Mature fine tailings and coke are waste products of the oil sands industry with potential for reclamation. A greenhouse study assessed whether substrates of various… (more)

Luna-Wolter, Gabriela L.

2012-01-01T23:59:59.000Z

150

Preparation of Activated Carbon from Oil Sands Coke by Chemical and Physical Activation Techniques.  

E-Print Network (OSTI)

??Oil sands coke is a by-product resulting from the upgrading of heavy crude bitumen to light synthetic oil. This research investigates the preparation of activated… (more)

Morshed, Golam

2012-01-01T23:59:59.000Z

151

Appraisal of the tight sands potential of the Sand Wash and Great Divide Basins. Final report, June 1989--June 1991  

Science Conference Proceedings (OSTI)

The volume of future tight gas reserve additions is difficult to estimate because of uncertainties in the characterization and extent of the resource and the performance and cost-effectiveness of stimulation and production technologies. Ongoing R&D by industry and government aims to reduce the risks and costs of producing these tight resources, increase the certainty of knowledge of their geologic characteristics and extent, and increase the efficiency of production technologies. Some basins expected to contain large volumes of tight gas are being evaluated as to their potential contribution to domestic gas supplies. This report describes the results of one such appraisal. This analysis addresses the tight portions of the Eastern Greater Green River Basin (Sand Wash and Great Divide Subbasins in Northwestern Colorado and Southwestern Wyoming, respectively), with respect to estimated gas-in-place, technical recovery, and potential reserves. Geological data were compiled from public and proprietary sources. The study estimated gas-in-place in significant (greater than 10 feet net sand thickness) tight sand intervals for six distinct vertical and 21 areal units of analysis. These units of analysis represent tight gas potential outside current areas of development. For each unit of analysis, a ``typical`` well was modeled to represent the costs, recovery and economics of near-term drilling prospects in that unit. Technically recoverable gas was calculated using reservoir properties and assumptions about current formation evaluation and extraction technology performance. Basin-specific capital and operating costs were incorporated along with taxes, royalties and current regulations to estimate the minimum required wellhead gas price required to make the typical well in each of unit of analysis economic.

Not Available

1993-08-01T23:59:59.000Z

152

Dependence of waterflood remaining oil saturation on relative permeability, capillary pressure, and reservoir parameters in mixed-wet turbidite sands  

SciTech Connect

The dependence of waterflood oil recovery on relative permeability, capillary pressure, and reservoir parameters was investigated by numerical simulation. The relative permeability and capillary pressure curves were based on laboratory measurements on unconsolidated sands. The water-wet case is based on the assumption that the system is water-wet and measurements were made with refined oil. The mixed-wet case assumed that the system is mixed-wet and restored-state measurements were made with crude oil. The reservoir model was a prototype turbidite sand with a range of thickness and permeability values. The economic oil recovery was based on an economic limit water cut of 50%. The remaining oil saturation (ROS) in the swept region for the water-wet cases was close to the residual oil saturation. The ROS of the mixed-wet cases ranged from low values near the residual oil saturation to far above the residual oil saturation. It is dependent on the reservoir parameters that govern (1) the vertical film surface drainage of oil by gravity, (2) accumulation of a high oil saturation and thus a high relative permeability under the caprock, and (3) up-dip migration of the oil that accumulated under the caprock. The dependence on the reservoir parameters can be summarized by dimensionless groups. There is a dimensionless time for the vertical displacement of oil by gravity. The accumulation of a high oil saturation under the caprock is dependent on the ratio of the capillary transition zone and the sand thickness. The updip migration is dependent on a combination of the gravity number and the endpoint mobility ratio.

Hirasaki, G.J. [Rice Univ., Houston, TX (United States)

1996-05-01T23:59:59.000Z

153

Hydraulic fracturing with a refractory proppant for sand control  

SciTech Connect

A sand control and heat transfer method is described for use in a borehole having an unconsolidated or loosely consolidated oil or gas reservoir which is otherwise likely to introduce substantial amounts of sand into the borehole, comprising: (a) providing a borehole casing through the reservoir; (b) perforating the casing at preselected intervals therealong to form at least one of longitudinal, in-line perforations; (c) hydraulically fracturing the reservoir by injecting a fracturing fluid containing a fine grain fused refractory material which comprises substantially silicon carbide or silicon nitride, and a clay stabilizing agent; (d) injecting a proppant comprising a gravel packing fused refractory material comprised substantially of silicon carbide or silicon nitride into the fracture, whereby a first layer of fine grain fused refractory material is held in place along the entire face of the fracture by a second layer of gravel packing fused refractory material also extending along the entire length of the fracture thereby excluding fines; and (e) producing oil or gas from the reservoir through the fracture into the borehole casing via a thermal oil recovery method which proppant and layers provide for increased heat transfer into the formation.

Jennings, A.R. Jr.; Stowe, L.R.

1989-04-04T23:59:59.000Z

154

Fluid Resistance Analysis of Sand Control Slotted Liner with Compound Cavity Based on Fluent  

Science Conference Proceedings (OSTI)

Slotted liners have been used for many years to provide sand control in many oil industry applications. They are commonly applied in reservoirs that produce high-viscosity oil from horizontal wells with unconsolidated, high-permeability sands. However, ... Keywords: slotted liner, newly-designed slot, Fluid resistance

Hang Li; Yonghong Liu; Jianmin Ma; Xinfang Wei

2010-03-01T23:59:59.000Z

155

Effect of temperature on wave velocities in sands and sandstones with heavy hydrocarbons  

SciTech Connect

A laboratory investigation was made of the effects of temperature on wave velocities in sandstones and unconsolidated sand saturated with heavy hydrocarbons. The large decreases of the compressional and shear velocities in such sandstones and sand with increasing temperature suggest that seismic methods may be very useful in detecting heat fronts in heavy hydrocarbon reservoirs undergoing steamflooding or in-situ combustion.

Wang, Z.; Nur, A.

1988-02-01T23:59:59.000Z

156

Guide to preparing SAND reports and other communication products : quick reference guide.  

SciTech Connect

This 'Quick Reference Guide' supplements the more complete 'Guide to Preparing SAND Reports and Other Communication Products'. It provides limited guidance on how to prepare SAND Reports at Sandia National Laboratories. Users are directed to the in-depth guide for explanations of processes.

Not Available

2007-03-01T23:59:59.000Z

157

Occurrence of gas hydrate in Oligocene Frio sand: Alaminos Canyon Block 818: Northern Gulf of Mexico  

E-Print Network (OSTI)

volumes of shale (gray), sand (yellow), gas hydrate-?lledgas hydrate-bearing zone is also bounded laterally with impermeable shaleshale section that overlies the Frio sand showing four-way closure that forms the trap for the AC818 gas

Boswell, R.D.

2010-01-01T23:59:59.000Z

158

A modeling approach for iron concentration in sand filtration effluent using adaptive neuro-fuzzy model  

Science Conference Proceedings (OSTI)

Effluent iron concentration is an important water quality criterion used for the assessment of the performance of rapid sand filters, in addition to other criteria. This study deals with the prediction of effluent iron concentrations by adaptive neuro-fuzzy ... Keywords: ANFIS, Effluent iron concentration, Modeling, Sand filtration

Mehmet Çakmakci; Cumali Kinaci; Mahmut Bayramo?lu; Y?lmaz Yildirim

2010-03-01T23:59:59.000Z

159

Modelling damping ratio and shear modulus of sand-mica mixtures using genetic programming  

Science Conference Proceedings (OSTI)

This study presents two Genetic Programming (GP) models for damping ratio and shear modulus of sand-mica mixtures based on experimental results. The experimental database used for GP modelling is based on a laboratory study of dynamic properties of saturated ... Keywords: Genetic programming, Leighton buzzard sand, Mica, Resonant column testing

Abdulkadir Cevik; Ali Firat Cabalar

2009-05-01T23:59:59.000Z

160

Guide to Preparing SAND Reports and other communication products : quick reference guide.  

Science Conference Proceedings (OSTI)

This Quick Reference Guide supplements the more complete Guide to Preparing SAND Reports and Other Communication Products. It provides limited guidance on how to prepare SAND Reports at Sandia National Laboratories. Users are directed to the in-depth guide for explanations of processes.

Not Available

2009-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Preliminary relative permeability estimates of methanehydrate-bearing sand  

Science Conference Proceedings (OSTI)

The relative permeability to fluids in hydrate-bearing sediments is an important parameter for predicting natural gas production from gas hydrate reservoirs. We estimated the relative permeability parameters (van Genuchten alpha and m) in a hydrate-bearing sand by means of inverse modeling, which involved matching water saturation predictions with observations from a controlled waterflood experiment. We used x-ray computed tomography (CT) scanning to determine both the porosity and the hydrate and aqueous phase saturation distributions in the samples. X-ray CT images showed that hydrate and aqueous phase saturations are non-uniform, and that water flow focuses in regions of lower hydrate saturation. The relative permeability parameters were estimated at two locations in each sample. Differences between the estimated parameter sets at the two locations were attributed to heterogeneity in the hydrate saturation. Better estimates of the relative permeability parameters require further refinement of the experimental design, and better description of heterogeneity in the numerical inversions.

Seol, Yongkoo; Kneafsey, Timothy J.; Tomutsa, Liviu; Moridis,George J.

2006-05-08T23:59:59.000Z

162

Preliminary relative permeability estimates of methanehydrate-bearing sand  

SciTech Connect

The relative permeability to fluids in hydrate-bearingsediments is an important parameter for predicting natural gas productionfrom gas hydrate reservoirs. We estimated the relative permeabilityparameters (van Genuchten alpha and m) in a hydrate-bearing sand by meansof inverse modeling, which involved matching water saturation predictionswith observations from a controlled waterflood experiment. We used x-raycomputed tomography (CT) scanning to determine both the porosity and thehydrate and aqueous phase saturation distributions in the samples. X-rayCT images showed that hydrate and aqueous phase saturations arenon-uniform, and that water flow focuses in regions of lower hydratesaturation. The relative permeability parameters were estimated at twolocations in each sample. Differences between the estimated parametersets at the two locations were attributed to heterogeneity in the hydratesaturation. Better estimates of the relative permeability parametersrequire further refinement of the experimental design, and betterdescription of heterogeneity in the numerical inversions.

Seol, Yongkoo; Kneafsey, Timothy J.; Tomutsa, Liviu; Moridis,George J.

2006-05-08T23:59:59.000Z

163

Western Gas Sands Project. Quarterly basin activities report  

SciTech Connect

A summation of information is presented on geology and drilling activity in the four primary study areas of the Western Gas Sands Project. The areas of interest are the Greater Green River Basin, the Piceance Basin, the Uinta Basin, and the Northern Great Plains Province. Drilling activity is discussed for the months of October, November, and December, 1977, with the major emphasis on wells located in low permeability sandstone areas, having significant gas production and utilizing hydraulic fracturing treatments. The drilling information was obtained primarily from ''The Rocky Mountain Region Report'' published by Petroleum Information Corporation on a daily basis. Another source of information was the ''Montana Oil and Gas Journal'' which is released weekly.

1978-01-01T23:59:59.000Z

164

CO{sub 2}/sand fracturing in Devonian shale  

Science Conference Proceedings (OSTI)

A total of five carbon dioxide (CO{sub 2}) /sand well stimulations were successfully executed with two Devonian shale operators in Perry and Pike Counties, Kentucky. This new stimulation method offers a minimum formation damage proppant stimulation approach for natural gas producers in the United States. Some operators have been concerned about the frac fluid formation damage associated with the water and chemicals used in conventional foam stimulations, whereas other operators have been concerned about the lack of proppant in straight nitrogen fracs used by service companies today. Two carefully screened geological areas of established Devonian shale production were selected based on active ongoing drilling and completion operations. One selected control area contained an existing set of wells with established production histories. The logistics and field layout of a typical carbon dioxide/sand frac treatment has been described and highlighted. The importance and unique aspects of the closed system blender that is required for job execution is discussed. Five stimulation treatments have been reviewed, and stimulation and preliminary production data compared to offset wells stimulated with nitrogen, and explosives. Initial production results indicate more than a 50 percent increase in production rate compared to nitrogen fraced wells in the Pike County area. In addition, production is also 4.8 times better than conventional shot wells in the same area. These results are encouraging enough to formally combine existing pumping equipment, a closed system blender, and liquid carbon dioxide supplies to develop a new fracturing service in the eastern US A total of 22 additional jobs are planned in the eastern US in low permeability gas formations over the next year.

Yost, A.B. II [USDOE Morgantown Energy Technology Center, WV (United States); Mazza, R.L. [Petroleum Consulting Services, Canton, OH (United States); Gehr, J.B. [Natural Gas Resources Corporation (United States)

1993-11-01T23:59:59.000Z

165

Retention behavior of dilute polymers in oil sands  

Science Conference Proceedings (OSTI)

Adequate mobility control between fluid banks is a pertinent factor in the successful application of secondary and tertiary oil recovery processes. Favorable mobilities can be obtained by increasing the viscosity or reducing the permeability to the displacing fluid phase. Polyacrylamide and oio-polymers have proved to be useful for these purposes. These polymers increase the water viscosity substantially at low concentrations. The resulting reduced mobility of the displacing phase suppresses the fingering phenomenon and improves piston-like displacement. However, the structural complexity of these polymers coupled with the complexity of the flow channels in the porous medium cause part of these polymers to be retained in the reservoir as the displacing fluid from advances, thereby causing a reduction in the concentration of the polymer solution and consequently a loss of mobility control. In addition to the mechanical filtering, adsorption on the grain surfaces reduce the polymer concentration in the displacing fluid. Behavior of polyacrylamide polymers has been studied extensively. Susceptibility of these polymers to salinity, pH, shear, temperature, etc., is well documented. Mechanical entrapment, retention, degradation and adsorption behavior on porous media, including fired Berea sandstone, bead packs and Ottawa sand have been reported. The present study investigates the adsorption and trapping of polymers in flow experiments through unconsolidated oil field sands. Effects of particle size and mineral content have been studied. Effect of a surfactant slug on polymer-rock interaction is also reported. Corroborative studies have been conducted to study the pressure behavior and high tertiary oil recovery in surfactant dilute-polymer systems.

Kikani, J.; Somerton, W.H.

1988-05-01T23:59:59.000Z

166

Alberta bound : the interface between Alberta's environmental policies and the environmental management of three Albertan oil sands companies  

E-Print Network (OSTI)

The Athabasca Oil Sands, located in northeastern Alberta, Canada, were for many years anomalous. Two oil sands operators developed their extraction techniques for 30 years, refining their technology before production became ...

Lemphers, Nathan C

2009-01-01T23:59:59.000Z

167

Geothermal investigations at selected thermal systems of the northern Wasatch Front Weber and Box Elder Counties, Utah. Report of investigation No. 141  

DOE Green Energy (OSTI)

Numerous thermal springs are present along the Wasatch Front from Utah valley on the south to the state line on the north. These systems are just west of the Wasatch Mountains at the eastern edge of the Basin and Range physiographic province and within the active seismic zone referred to as the Intermountain Seismic Belt. This Report of Investigation is a summary of UGMS investigations at four northern Wasatch Front geothermal systems: Utah, Crystal (Madsen), and Udy hot springs; and the Little Mountain - south system. All of these resources are deep circulation systems and the water is heated by the normal heat flow of the Basin and Range Province. Heat from volcanic sources is not believed to contribute to the warming of any northern Wasatch Front springs. Data collected under the DOE/DGE state coupled program are presented for use by individuals interested in these systems.

Murphy, P.; Gwynn, J.W.

1979-11-01T23:59:59.000Z

168

Characterization of nickel and vanadium compounds in tar sand bitumen by UV-VIS spectroscopy and size exclusion chromatography coupled with element specific detection  

Science Conference Proceedings (OSTI)

Previously, the authors examined the Ni and V in heavy crude oils, residua, and processed products by several metal speciation techniques to ascertain molecular structure and processing behavior. Two classes of metal compounds were found - metallopetroporphyrins and metallo-nonprophyrins - each having unique reactivity during processing. In efforts to better understand the binding of metals in the oil medium, they now examine NI and V in tar sand bitumens. The bitumen was solvent extracted from the sand matrix and was separated by column chromatography and the petroporphyrin content was quantitated by UV-vis spectroscopy. The petroporphyrin contents ranged from virtually none to over 36% of the total metals. Asphalt Ridge (Utah) has primarily Ni petroporphyrins; Big Clifty (Kentucky) and Athabasca (Canada) have primarily V petroporphyrins; Arroyo Grande and McKittrick (California) have roughly equal amounts of both types; and Sunnyside (Utah) has virtually none of either.

Reynolds, J.G.; Jones, E.L.; Bennett, J.A. (Lawrence Livermore National Lab., CA (USA)); Biggs, W.R. (Chevron Research Co., Richmond, CA (USA))

1989-01-01T23:59:59.000Z

169

Experience with SAND-Tcl: A Scripting Tool for Spatial Databases 1 CLAUDIO ESPERANC A (Contact Author)  

E-Print Network (OSTI)

Experience with SAND-Tcl: A Scripting Tool for Spatial Databases 1 CLAUDIO ESPERANC¸ A (Contact. This is illustrated by de- scribing our experience with SAND-Tcl, a scripting tool developed by us for building spatial database applications. SAND-Tcl is an extension of the Tcl embedded scripting language

Samet, Hanan

170

The evaluation of waterfrac technology in low-permeability gas sands in the East Texas basin  

E-Print Network (OSTI)

The petroleum engineering literature clearly shows that large proppant volumes and concentrations are required to effectively stimulate low-permeability gas sands. To pump large proppant concentrations, one must use a viscous fluid. However, many operators believe that low-viscosity, low-proppant concentration fracture stimulation treatments known as ??waterfracs?? produce comparable stimulation results in low-permeability gas sands and are preferred because they are less expensive than gelled fracture treatments. This study evaluates fracture stimulation technology in tight gas sands by using case histories found in the petroleum engineering literature and by using a comparison of the performance of wells stimulated with different treatment sizes in the Cotton Valley sands of the East Texas basin. This study shows that large proppant volumes and viscous fluids are necessary to optimally stimulate tight gas sand reservoirs. When large proppant volumes and viscous fluids are not successful in stimulating tight sands, it is typically because the fracture fluids have not been optimal for the reservoir conditions. This study shows that waterfracs do produce comparable results to conventional large treatments in the Cotton Valley sands of the East Texas basin, but we believe it is because the conventional treatments have not been optimized. This is most likely because the fluids used in conventional treatments are not appropriate or have not been used appropriately for Cotton Valley conditions.

Tschirhart, Nicholas Ray

2005-08-01T23:59:59.000Z

171

Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt  

SciTech Connect

This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: a statistically sound evaluation of the characterization of foundry sand, a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at Nini, Ndes, and Nmax. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

Paul J. Tikalsky, Hussain U. Bahia, An Deng and Thomas Snyder

2004-10-15T23:59:59.000Z

172

Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt  

Science Conference Proceedings (OSTI)

This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: (1) a statistically sound evaluation of the characterization of foundry sand, (2) a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and (3) the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at N{sub ini}, N{sub des}, and N{sub max}. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

Pauul J. Tikalsky

2004-10-31T23:59:59.000Z

173

Range of Glaciers: The Exploration of the Northern Cascade Range  

E-Print Network (OSTI)

D. Hook, Reference Librarian, University of Idaho Library,Moscow, Idaho 83844-2350, (208) 885-6066.Robert D. Hook University of Idaho, USA Fred Beckey. Range

Hook, Robert D.

2006-01-01T23:59:59.000Z

174

Collection of technical data for tight gas sands in support of the massive hydraulic fracturing system. Final report  

SciTech Connect

Results are presented of work performed to study case histories of logging problems/requirements in tight gas sand areas, provide production histories/completion information on selected Uinta Basin tight gas sand wells, provide geologic guidance and additional technical input for computer simulation of tight gas sand well behavior, and develop information about production histories, completion techniques and reservoir rock characteristics from selected tight gas sand key wells in the Piceance and Green River Basins. A list of gas sand wells in the Uinta Basin is included along with gas production statistics, completion and reservoir data, and well production data. (JRD)

Knutson, C.F.; Boardman, C.R.

1978-09-20T23:59:59.000Z

175

CAVITY LIKE COMPLETIONS IN WEAK SANDS PREFERRED UPSTREAM MANAGEMENT PRACTICES  

SciTech Connect

The technology referred to as Cavity Like Completions (CLC) offers a new technique to complete wells in friable and unconsolidated sands. A successfully designed CLC provides significant increases in well PI (performance index) at lower costs than alternative completion techniques. CLC technology is being developed and documented by a partnership of major oil and gas companies through a GPRI (Global Petroleum Research Institute) joint venture. Through the DOE-funded PUMP program, the experiences of the members of the joint venture will be described for other oil and gas producing companies. To date six examples of CLC completions have been investigated by the JV. The project was performed to introduce a new type of completion (or recompletion) technique to the industry that, in many cases, offers a more cost effective method to produce oil and gas from friable reservoirs. The project's scope of work included: (1) Further develop theory, laboratory and field data into a unified model to predict performance of cavity completion; (2) Perform at least one well test for cavity completion (well provided by one of the sponsor companies); (3) Provide summary of geo-mechanical models for PI increase; and (4) Develop guidelines to evaluate success of potential cavity completion. The project tracks the experiences of a joint industry consortium (GPRI No. 17) over a three year period and compiles results of the activities of this group.

Ian Palmer; John McLennan

2004-04-30T23:59:59.000Z

176

Guide to preparing SAND reports and other communication products.  

SciTech Connect

This guide describes the R&A process, Common Look and Feel requirements, and preparation and publishing procedures for communication products at Sandia National Laboratories. Samples of forms and examples of published communications products are provided. This guide takes advantage of the wealth of material now available on the Web as a resource. Therefore, it is best viewed as an electronic document. If some of the illustrations are too small to view comfortably, you can enlarge them on the screen as needed. The format of this document is considerably different than that usually expected of a SAND Report. It was selected to permit the large number of illustrations and examples to be placed closer to the text that references them. In the case of forms, covers, and other items that are included as examples, a link to the Web is provided so that you can access the items and download them for use. This guide details the processes for producing a variety of communication products at Sandia National Laboratories. Figure I-1 shows the general publication development process. Because extensive supplemental material is available from Sandia on the internal web or from external sources (Table I-1), the guide has been shortened to make it easy to find information that you need.

Not Available

2011-09-01T23:59:59.000Z

177

Property:Wave Period Range(s) | Open Energy Information  

Open Energy Info (EERE)

Wave Period Range(s) Wave Period Range(s) Jump to: navigation, search Property Name Wave Period Range(s) Property Type String Pages using the property "Wave Period Range(s)" Showing 25 pages using this property. (previous 25) (next 25) 1 1.5-ft Wave Flume Facility + 10.0 + 10-ft Wave Flume Facility + 0.0 + 11-ft Wave Flume Facility + 10.0 + 2 2-ft Flume Facility + 10.0 + 3 3-ft Wave Flume Facility + 10.0 + 5 5-ft Wave Flume Facility + 10.0 + 6 6-ft Wave Flume Facility + 10.0 + A Alden Large Flume + 2.1 + Alden Small Flume + 0.0 + Alden Wave Basin + 1.0 + B Breakwater Research Facility + 0.0 + C Carderock Maneuvering & Seakeeping Basin + 0.0 + Carderock Tow Tank 2 + 0.0 + Carderock Tow Tank 3 + 0.0 + Chase Tow Tank + 3.1 + Coastal Harbors Modeling Facility + 2.3 +

178

An Observational Analysis and Evaluation of Land Surface Model Accuracy in the Nebraska Sand Hills  

Science Conference Proceedings (OSTI)

In this study, the influence of subsurface water on the energy budget components of three locations with heterogeneous land surfaces in the Nebraska Sand Hills are examined through observations and use of the Noah land surface model (LSM). ...

David B. Radell; Clinton M. Rowe

2008-08-01T23:59:59.000Z

179

Characterization Report on Sand, Slag, and Crucible Residues and on Fluoride Residues  

Science Conference Proceedings (OSTI)

This paper reports on the chemical characterization of the sand, slag, and crucible (SS and C) residues and the fluoride residues that may be shipped from the Rocky Flats Environmental Technology Site (RFETS) to Savannah River Site (SRS).

Murray, A.M.

1999-02-10T23:59:59.000Z

180

Technologies, markets and challenges for development of the Canadian Oil Sands industry  

E-Print Network (OSTI)

This paper provides an overview of the current status of development of the Canadian oil sands industry, and considers possible paths of further development. We outline the key technology alternatives, critical resource ...

Lacombe, Romain H.

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Engineering assessment of radioactive sands and residues, Lowman Site, Lowman, Idaho  

SciTech Connect

Ford, Bacon and Davis Utah Inc. has reevaluated the Lowman site in order to revise the December 1977 engineering assessment of the problems resulting from the existence of radioactive sands and residues at Lowman, Idaho. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of radioactive sands and residues and radiation exposure of individuals and nearby populations, and investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the 191,000 tons of radioactive sands, residues, and contaminated soils at the Lowman site constitutes the most significant environmental impact, although windblown radioactive sands and external gamma radiation also are factors.

Not Available

1981-09-01T23:59:59.000Z

182

Determination of soil liquefaction characteristics by large-scale laboratory tests. [Sand  

SciTech Connect

The testing program described in this report was carried out to study the liquefaction behavior of a clean, uniform, medium sand. Horizontal beds of this sand, 42 inches by 90 inches by 4 inches were prepared by pluviation with a special sand spreader, saturated, and tested in a shaking table system designed for this program, which applied a horizontal cyclic shear stress to the specimens. Specimen size was selected to reduce boundary effects as much as possible. Values of pore pressures and shear strains developed during the tests are presented for sand specimens at relative densities of 54, 68, 82, and 90 percent, and the results interpreted to determine the values of the stress ratio causing liquefaction at the various relative densities.

1975-05-01T23:59:59.000Z

183

Temperature, Precipitation, and Lightning Modification in the Vicinity of the Athabasca Oil Sands  

Science Conference Proceedings (OSTI)

The Athabasca oil sands development in northeast Alberta, Canada, has disturbed more than 500 km2 of boreal forest through surface mining and tailings ponds development. In this paper, the authors compare the time series of temperatures and ...

Daniel M. Brown; Gerhard W. Reuter; Thomas K. Flesch

2011-12-01T23:59:59.000Z

184

CONTRACTOR REPORT SAND952729 Unlimited Release U G A Q O D  

Office of Scientific and Technical Information (OSTI)

r x 12-N -. CONTRACTOR REPORT SAND952729 Unlimited Release U G A Q O D Evaluation of Polyacrylonitrile (PAN) as a Binding Polymer for Absorbers Used to-Treat Liquid Radioactive...

185

Investigation of sand consolidation using steam for the Tar Zone, Wilmington field, California.  

E-Print Network (OSTI)

??An experimental study was carried out to better understand and optimize the process of sand consolidation using high-pH steam in wells of the Wilmington field,… (more)

Nilsen, Knut Arild

2012-01-01T23:59:59.000Z

186

Integration of High Temperature Gas-cooled Reactor Technology with Oil Sands Processes  

Science Conference Proceedings (OSTI)

This paper summarizes an evaluation of siting an HTGR plant in a remote area supplying steam, electricity and high temperature gas for recovery and upgrading of unconventional crude oil from oil sands. The area selected for this evaluation is the Alberta Canada oil sands. This is a very fertile and active area for bitumen recovery and upgrading with significant quantities piped to refineries in Canada and the U.S Additionally data on the energy consumption and other factors that are required to complete the evaluation of HTGR application is readily available in the public domain. There is also interest by the Alberta oil sands producers (OSP) in identifying alternative energy sources for their operations. It should be noted, however, that the results of this evaluation could be applied to any similar oil sands area.

L.E. Demick

2011-10-01T23:59:59.000Z

187

An Investigation for Disposal of Drill Cuttings into Unconsolidated Sandstones and Clayey Sands  

Science Conference Proceedings (OSTI)

This project include experimental data and a set of models for relating elastic moduli/porosity/texture and static-to-dynamic moduli to strength and failure relationships for unconsolidated sands and clayey sands. The results of the project should provide the industry with a basis for wider use of oil base drilling fluids in water sensitive formations by implementing drill cutting injection into existing wells at abandoned formations and controlling fracture geometry to prevent ground water contamination.

Mese, Ali; Dvorkin, Jack; Shillinglaw, John

2000-09-11T23:59:59.000Z

188

Economics of tight sands gas extraction as affected by r and d. Occasional pub  

SciTech Connect

The paper examines the economics and resource potential of tight sand formations as a major near-term source of unconventional gas. The main vehicles for analyzing the issues to date are the 1980 study by the National Petroleum Council (NPC) on tight sand resources and two studies based on the NPC's work at different stages of completion for the GRI Center for Energy Systems Analysis (CESA).

Rosenberg, J.

1983-08-01T23:59:59.000Z

189

Paleontological overview of oil shale and tar sands areas in Colorado, Utah, and Wyoming.  

Science Conference Proceedings (OSTI)

In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the ''Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005,'' Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. In addition, Congress declared that both research- and commercial-scale development of oil shale and tar sands should (1) be conducted in an environmentally sound manner using management practices that will minimize potential impacts, (2) occur with an emphasis on sustainability, and (3) benefit the United States while taking into account concerns of the affected states and communities. To support this declaration of policy, Congress directed the Secretary of the Interior to undertake a series of steps, several of which are directly related to the development of a commercial leasing program for oil shale and tar sands. One of these steps was the completion of a programmatic environmental impact statement (PEIS) to analyze the impacts of a commercial leasing program for oil shale and tar sands resources on public lands, with an emphasis on the most geologically prospective lands in Colorado, Utah, and Wyoming. For oil shale, the scope of the PEIS analysis includes public lands within the Green River, Washakie, Uinta, and Piceance Creek Basins. For tar sands, the scope includes Special Tar Sand Areas (STSAs) located in Utah. This paleontological resources overview report was prepared in support of the Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and PEIS, and it is intended to be used by Bureau of Land Management (BLM) regional paleontologists and field office staff to support future projectspecific analyses. Additional information about the PEIS can be found at http://ostseis.anl.gov.

Murphey, P. C.; Daitch, D.; Environmental Science Division

2009-02-11T23:59:59.000Z

190

Unsaturated hydraulic conductivity of compacted sand-kaolin mixtures  

SciTech Connect

The unsaturated hydraulic conductivity of compacted sand-kaolin mixtures containing 0, 5, 10, and 30% kaolin (by dry weight) is measured for matric suctions, {psi}{sub m} < {approximately} 6.0 m. The measured unsaturated hydraulic conductivity (k{sub m}) values are compared with predicted unsaturated hydraulic conductivity (k{sub p}) values using the Brooks-Corey-Burdine and van Genuchten-Mualem relative hydraulic conductivity functions. In general, the accuracy of k{sub p} decreases with an increase in kaolin content or an increase in {psi}{sub m}. In addition, k{sub m} tends to be underpredicted for kaolin contents of 10 and 30% at relatively high suctions (1.0 m {le} {psi}{sub m} {le} 6.0 m) and overpredicted for kaolin contents of 0 and 5% at relatively low suctions (0.1 m {le} {psi}{sub m} < 1.0 m). For a given kaolin content and {psi}{sub m}, k{sub p} based on the Brooks-Corey-Burdine function tends to be more accurate than k{sub m} based on the van Genuchten-Mualem function. Finally, for 1.0 m {le} {psi}{sub m} {le} 6.0 m, k{sub p} based on analysis using the maximum volumetric water content ({theta}{sub m}) attained under steady-state flow conditions typically is more accurate than k{sub p} based on analysis using the saturated volumetric water content, {theta}{sub s}, where {theta}{sub m} {approximately} 84--90% of {theta}{sub s} in this study.

Chiu, T.F. [Genesis Group, Taipei (Taiwan, Province of China); Shackelford, C.D. [Colorado State Univ., Fort Collins, CO (United States). Dept. of Civil Engineering

1998-02-01T23:59:59.000Z

191

FIELD TESTING & OPTIMIZATION OF CO2/SAND FRACTURING TECHNOLOGY  

SciTech Connect

These contract efforts involved the demonstration of a unique liquid free stimulation technology which was, at the beginning of these efforts, in 1993 unavailable in the US. The process had been developed, and patented in Canada in 1981, and held promise for stimulating liquid sensitive reservoirs in the US. The technology differs from that conventionally used in that liquid carbon dioxide (CO{sub 2}), instead of water is the base fluid. The CO{sub 2} is pumped as a liquid and then vaporizes at reservoir conditions, and because no other liquids or chemicals are used, a liquid free fracture is created. The process requires a specialized closed system blender to mix the liquid CO{sub 2} with proppant under pressure. These efforts were funded to consist of up to 21 cost-shared stimulation events. Because of the vagaries of CO{sub 2} supplies, service company support and operator interest only 19 stimulation events were performed in Montana, New Mexico, and Texas. Final reports have been prepared for each of the four demonstration groups, and the specifics of those demonstrations are summarized. A summary of the demonstrations of a novel liquid-free stimulation process which was performed in four groups of ''Candidate Wells'' situated in Crockett Co., TX; San Juan Co., NM; Phillips Co., MT; and Blaine Co., MT. The stimulation process which employs CO{sub 2} as the working fluid and the production responses were compared with those from wells treated with conventional stimulation technologies, primarily N{sub 2} foam, excepting those in Blaine Co., MT where the reservoir pressure is too low to clean up spent stimulation liquids. A total of 19 liquid-free CO{sub 2}/sand stimulations were performed in 16 wells and the production improvements were generally uneconomic.

Raymond L. Mazza

2004-11-30T23:59:59.000Z

192

Dynamic Behavior of Sand: Annual Report FY 11  

SciTech Connect

Currently, design of earth-penetrating munitions relies heavily on empirical relationships to estimate behavior, making it difficult to design novel munitions or address novel target situations without expensive and time-consuming full-scale testing with relevant system and target characteristics. Enhancing design through numerical studies and modeling could help reduce the extent and duration of full-scale testing if the models have enough fidelity to capture all of the relevant parameters. This can be separated into three distinct problems: that of the penetrator structural and component response, that of the target response, and that of the coupling between the two. This project focuses on enhancing understanding of the target response, specifically granular geomaterials, where the temporal and spatial multi-scale nature of the material controls its response. As part of the overarching goal of developing computational capabilities to predict the performance of conventional earth-penetrating weapons, this project focuses specifically on developing new models and numerical capabilities for modeling sand response in ALE3D. There is general recognition that granular materials behave in a manner that defies conventional continuum approaches which rely on response locality and which degrade in the presence of strong response nonlinearities, localization, and phase gradients. There are many numerical tools available to address parts of the problem. However, to enhance modeling capability, this project is pursuing a bottom-up approach of building constitutive models from higher fidelity, smaller spatial scale simulations (rather than from macro-scale observations of physical behavior as is traditionally employed) that are being augmented to address the unique challenges of mesoscale modeling of dynamically loaded granular materials. Through understanding response and sensitivity at the grain-scale, it is expected that better reduced order representations of response can be formulated at the continuum scale as illustrated in Figure 1 and Figure 2. The final result of this project is to implement such reduced order models in the ALE3D material library for general use.

Antoun, T; Herbold, E; Johnson, S

2012-03-15T23:59:59.000Z

193

Radium-226 and calcium uptake by crops grown in mixtures of sand and cay tailings from phosphate mining  

Science Conference Proceedings (OSTI)

Radium-226 is a naturally occurring radionuclide found in reclaimed clay and sand tailing from phosphate mining. Field studies were conducted to investigate the effects of sand/clay ratio (SCR), Ca supplement and organic amendments on the {sup 226}Ra concentration in turnip, banana pepper, cabbage, yellow squash, mustard, and alfalfa. For vegetables, treatment effects included SCR (2:1, 4:1, 6:1, and 8:1), phosphogypsum (PG) 0,22, and 134 Mg ha{sup {minus}1}, and peat 0,100, and 200 Mg ha{sup {minus}1}. For alfalfa grown in a 1:1 SCR mixture, treatments included organic amendments (control, peat, sewage slude, sawdust, composted sewage sludge, composted garbage and humate) applied at 44.8 Mg ha{sup {minus}1} (2.2 Mg ha{sup {minus}1} for humate). Plant {sup 226}Ra concentration tended to be higher in the 4:1 than in the 2:1 SCR mix but this depended on the crop an d the season. Organic amendments and PG had no effect (p<0.05) on the {sup 226}Ra concentration in vegetables and alfalfa. Mean {sup 226}Ra concentration in plant tissues ranged from 3.4 Bq kg{sup {minus}1} in banana pepper fruit to 31.1 Bq kg{sup {minus}1}. A quadratic relationship based on 631 observations was observed between {sup 226}Ra and Ca concentration in plant tissues. The {sup 226}Ra/Ca ratio in plant tissues ranged from 0.85 to 2.13 kBq {sup 226}Ra kg{sup {minus}1} Ca and decreased with increasing plant {sup 226}Ra. Results indicated that wide differences in plant {sup 226}Ca concentration were related more to differences in plant Ca levels than to soil factors. 21 refs., 1 fig., 6 tabs.

Million, J.B. [Univ. of Hawaii, Hilo, HI (United States); Sartain, J.B. [Univ. of Florida, Gainesville, FL (United States); Gonzalez, R.X.; Carrier, W.D. III [Bromwell & Carrier, Lakeland, FL (United States)

1994-07-01T23:59:59.000Z

194

APS Long Range Operations Schedule  

NLE Websites -- All DOE Office Websites (Extended Search)

Shutdown Planning Shutdown Planning Planning Templates Shutdown Planning Schedules: Current Shutdown Schedule Archives: 2006 - 2013 APS Long-Range Operations Schedule: 2014 Archives: 2013 | 2012 2011 | 2010 | 2009 | 2008 2007 | 2006 | 2005 | 2004 2003 | 2002 | 2001 | 2000 1999 | 1998 | 1997 | 1996 APS Long-Range Operations Schedule (Fiscal Year 2014) Alternate Formats: iCal | Excel | PDF APS Long-Range Operation Schedule 2013-3 2014-1 2014-2 Sep Oct Nov Dec Jan Feb Mar Apr May Jun Jul Aug Sep 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2

195

Experimental investigation of sand consolidation using high-temperature alkaline solution  

E-Print Network (OSTI)

An experimental study was conducted to better understand the sand consolidation process under high-temperature alkaline solution. Wilmington Tar sand samples were successfully consolidated in the laboratory using high-temperature (250-260?C) solution of sodium carbonate (pH 11-12). The sample was placed in a vertical 18 in. long aluminum cylindrical cell with an ID of 1.5 in.. The top half of the cell was thermally insulated while the bottom half was cooled. Hot alkaline solution was injected at 20 ml/min for 3-4 hours at the top of the cell and liquid produced at the bottom of the cell. After each experiment, the cell contents were removed and analyzed to determine if sand consolidation occurred. Both aggregates of sand grains and sectioned and polished epoxy-mounted sand grains were examined and analyzed using an electron microprobe to determine any change in shape, size, or composition of the sand pack and precipitation and growth of secondary phases. To better understand the process, experiments were subsequently conducted using samples of pure quartz, pure feldspar, and a 50:50 (by weight) mixture of quartz and feldspar. In each case, both varied 20-40 mesh and 50-250 mesh grain size samples were used. For the 20-40 mesh cases, zeolites and a mixture of amorphous silica and sodium carbonate were deposited on grain surfaces but were insufficient to cause overall sand consolidation. However, when a finer, poorly sorted (50-250 mesh) 50:50 mixture of feldspar and quartz was used, sand consolidation was obtained in 2.5 hours. At the top, hotter part of the cell, equant and acicular zeolite crystals (sodium aluminum silicates) weakly bound the sand grains. At the bottom and cooler part of the cell, the sand grains were strongly bound by a mixture of amorphous silica and sodium carbonate. Results to-date indicate that both zeolite and silica may be cementing agents, the grain-bonding strength depending on the grain surface area. This investigation is part of an ongoing research. The temperature, injection rate, and pH of the alkaline solution, treating time and "soaking period" are considered important process parameters that need to be further investigated.

Moreno Romero, Fidel Enrique

2000-01-01T23:59:59.000Z

196

Adaptively parallelizing distributed range queries  

Science Conference Proceedings (OSTI)

We consider the problem of how to best parallelize range queries in a massive scale distributed database. In traditional systems the focus has been on maximizing parallelism, for example by laying out data to achieve the highest throughput. However, ...

Ymir Vigfusson; Adam Silberstein; Brian F. Cooper; Rodrigo Fonseca

2009-08-01T23:59:59.000Z

197

SANDIA REPORT SAND2007-4407P Unlimited Release  

NLE Websites -- All DOE Office Websites (Extended Search)

Tonopah Test Range U UDP underground discharge points USAF U.S. Air Force USFS U.S. Forest Service USGS U.S. Geological Survey USN United States Navy UST underground storage...

198

RANGE INCREASER FOR PNEUMATIC GAUGES  

DOE Patents (OSTI)

An improved pneumatic gage is offered in which the linear range has been increased without excessive air consumption. This has been accomplished by providing an expansible antechamber connected to the nozzle of the gage so that the position of the nozzle with respect to the workpiece is varied automatically by variation in pressure within the antechamber. This arrangement ensures that the nozzle-to-workpiece clearance is maintained within certain limits, thus obtaining a linear relation of air flow to nozzle-to-workpiece clearance over a wider range.

Fowler, A.H.; Seaborn, G.B. Jr.

1960-09-27T23:59:59.000Z

199

Sand deformation concept for in-situ recovery of bitumen by cyclic steam injection  

SciTech Connect

Historically, a vertical or horizontal fracture is believed to be a main recovery mechanism for a cyclic steam injection process from the unconsolidated oil sands. Most of the current computer models for the process are based on the fracture concept. With the new postulated ''Sand Deformation Concept'' on the other hand, the injected fluid is able to penetrate the unconsolidated oil sand by creating microchannels. When the pore pressure is reduced during production, these secondary flow channels will totally or partially collapse. Condensed steam tends to sweep fluids where the bitumen had been heated and imparts mobility due to the injected hot fluid. Flow geometry of the new concept was fully investigated in this study. The physical differences between the sand deformation zone and the no-deformation zone were also investigated. The major differences zone were also investigated. The major differences between these two zones are a porosity change, a pressure level and energy and flow characteristics resulting from the existence of microchannels. All of these modifications were successfully incorporated into a conventional numerical thermal simulator. The new model provided an excellent match for all the field observations (steam injection pressure, oil-and-water production rates, fluid production temperature, downhole production pressure and the salinity changes) of a steam stimulated well in an unconsolidated oil sand. Conclusion from the study indicates that the most important phenomenon for in-situ recovery of bitumen is the one way valve effect of the microchannels which are opened during injection and closed during production.

Ito, Y.

1982-09-01T23:59:59.000Z

200

The extraction of bitumen from western oil sands. Annual report, July 1991--July 1992  

SciTech Connect

The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximately 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report.

Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1992-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Disjointed connections : the presidential permitting of tar sands oil pipelines at the U.S.-Canadian border.  

E-Print Network (OSTI)

??The fuel for dynamic change in the United State’s energy relationship with Canada lies in immense deposits of tar sands beneath the boreal forests of… (more)

Tomasovic, Brian Scott

2011-01-01T23:59:59.000Z

202

Evaluation of metals release from oil sands coke : an ecotoxicological assessment of risk and hazard to aquatic invertebrates .  

E-Print Network (OSTI)

??The oil sands operations in northeast Alberta, Canada, employ unconventional processes to produce synthetic crude oil (SCO). Because the extracted bitumen, ¡®the form of oil… (more)

PUTTASWAMY, NAVEEN V

2011-01-01T23:59:59.000Z

203

Range Fuels | Open Energy Information  

Open Energy Info (EERE)

Fuels Fuels Jump to: navigation, search Logo: Range Fuels Name Range Fuels Address 11101 W. 120th Avenue Place Broomfield, Colorado Zip 80021 Sector Biomass Product Uses a thermochemical process to turn biomass into synthetic gas and then fuel Website http://www.rangefuels.com/ Coordinates 39.915572°, -105.122053° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.915572,"lon":-105.122053,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

204

Range gated strip proximity sensor  

DOE Patents (OSTI)

A range gated strip proximity sensor uses one set of sensor electronics and a distributed antenna or strip which extends along the perimeter to be sensed. A micro-power RF transmitter is coupled to the first end of the strip and transmits a sequence of RF pulses on the strip to produce a sensor field along the strip. A receiver is coupled to the second end of the strip, and generates a field reference signal in response to the sequence of pulse on the line combined with received electromagnetic energy from reflections in the field. The sensor signals comprise pulses of radio frequency signals having a duration of less than 10 nanoseconds, and a pulse repetition rate on the order of 1 to 10 MegaHertz or less. The duration of the radio frequency pulses is adjusted to control the range of the sensor. An RF detector feeds a filter capacitor in response to received pulses on the strip line to produce a field reference signal representing the average amplitude of the received pulses. When a received pulse is mixed with a received echo, the mixing causes a fluctuation in the amplitude of the field reference signal, providing a range-limited Doppler type signature of a field disturbance. 6 figs.

McEwan, T.E.

1996-12-03T23:59:59.000Z

205

Range gated strip proximity sensor  

DOE Patents (OSTI)

A range gated strip proximity sensor uses one set of sensor electronics and a distributed antenna or strip which extends along the perimeter to be sensed. A micro-power RF transmitter is coupled to the first end of the strip and transmits a sequence of RF pulses on the strip to produce a sensor field along the strip. A receiver is coupled to the second end of the strip, and generates a field reference signal in response to the sequence of pulse on the line combined with received electromagnetic energy from reflections in the field. The sensor signals comprise pulses of radio frequency signals having a duration of less than 10 nanoseconds, and a pulse repetition rate on the order of 1 to 10 MegaHertz or less. The duration of the radio frequency pulses is adjusted to control the range of the sensor. An RF detector feeds a filter capacitor in response to received pulses on the strip line to produce a field reference signal representing the average amplitude of the received pulses. When a received pulse is mixed with a received echo, the mixing causes a fluctuation in the amplitude of the field reference signal, providing a range-limited Doppler type signature of a field disturbance.

McEwan, Thomas E. (Livermore, CA)

1996-01-01T23:59:59.000Z

206

Laboratory Analysis of a New Sand Consolidation Material for Oilfield Applications  

E-Print Network (OSTI)

The production of sand can be a major issue in many young, unconsolidated sandstone formations where there is little to no cement holding the individual sand grains together. When such reservoirs are produced, quite often operators face problems with reduced well productivity and equipment failure. Because of these issues, the industry has developed numerous techniques in its effort to control formation sand production. Sand consolidation is one technology that has been studied and used since the 1940s. The theory behind sand consolidation technology is to place a liquid material which will create a grain to grain contact that will bind individual sand grains together. Most consolidation treatments contain a preflush to clean and wet the surface, the consolidating system to bind the sand grains and give residual strength, and, finally, an overflush to ensure the formation is still able to produce fluids. With the successful placement of this fluid, the sand grains will be locked in placed so that they will not be produced. The technology has gone through many phases of conception since the 1940s; however, most consolidation material that is pumped in the past has been based upon an epoxy or furan backbone. While there are many technologies available, for the purpose of my research, the epoxy technology was experimentally investigated. The testing of the fluid involved investigating numerous additives to obtain the correct residual strength of the sample, as well as the necessary retained permeability. For the epoxy fluid, the optimal preflush, epoxy system and overflush formulations were determined after 250 checkout tests. Based upon these tests, the fluid was optimized to its working time and UCS results. The optimal system included the addition of PA2 to the preflush, along with PA1 and an aromatic amine curing agent to the epoxy system. PA1 and PA2 are adhesion promoter additives which were deemed necessary as a result of the testing. This system was then tested further in a HP/HT cell. While there is still room for improvement with respect to retained permeability, the system still performs very well in terms of UCS.

Filbrandt, Joseph Daniel

2010-12-01T23:59:59.000Z

207

Three-dimensional geometry of fluvial reservoir sands: steam-drive case study  

Science Conference Proceedings (OSTI)

The three-dimensional geometry of fluvial sands in South Belridge heavy oil field was investigated as part of an Enhanced Oil Recovery study. It was shown that only close-spaced well data are sufficient to define the sand-body geometries and heterogeneities of multichannelled fluvial systems. Reservoir flow-unit patterns cannot necessarily be correctly delineated by isolated vertical sequence analysis. Wireline logs from 19 wells and conventional cores from seven wells in a 10-ac (660 ft x 660 ft) pattern were correlated in detail, using additional input from sedimentology, steam-flow patterns, and reservoir flow-unit continuity.

McPherson, J.G.; Miller, D.D.

1989-03-01T23:59:59.000Z

208

APS Long Range Operations Schedule  

NLE Websites -- All DOE Office Websites (Extended Search)

3) 3) Alternate Formats: iCal | Excel | PDF APS Long-Range Operation Schedule 2012-3 2013-1 2013-2 Sep Oct Nov Dec Jan Feb Mar Apr May Jun Jul Aug Sep 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5

209

APS Long Range Operations Schedule  

NLE Websites -- All DOE Office Websites (Extended Search)

2) 2) Alternate Formats: iCal | Excel | PDF APS Long-Range Operation Schedule 2011-3 2012-1 2012-2 Sep Oct Nov Dec Jan Feb Mar Apr May Jun Jul Aug Sep 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5

210

APS Long Range Operations Schedule  

NLE Websites -- All DOE Office Websites (Extended Search)

1) 1) Alternate Formats: iCal | Excel | PDF APS Long-Range Operation Schedule 2010-3 2011-1 2011-2 Sep Oct Nov Dec Jan Feb Mar Apr May Jun Jul Aug Sep 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5

211

Extended-range tiltable micromirror  

DOE Patents (OSTI)

A tiltable micromirror device is disclosed in which a micromirror is suspended by a progressive linkage with an electrostatic actuator (e.g. a vertical comb actuator or a capacitive plate electrostatic actuator) being located beneath the micromirror. The progressive linkage includes a pair of torsion springs which are connected together to operate similar to a four-bar linkage with spring joints. The progressive linkage provides a non-linear spring constant which can allow the micromirror to be tilted at any angle within its range substantially free from any electrostatic instability or hysteretic behavior.

Allen, James J. (Albuquerque, NM); Wiens, Gloria J. (Newberry, FL); Bronson, Jessica R. (Gainesville, FL)

2009-05-05T23:59:59.000Z

212

STOCK DEFINITION AND GEOGRAPHIC RANGE  

E-Print Network (OSTI)

Sperm whales are found throughout the world's oceans in deep waters to the edge of the ice at both poles (Leatherwood and Reeves 1983; Rice 1989; Whitehead 2002). Sperm whales throughout the world exhibit a geographic social structure where females and juveniles of both sexes occur in mixed groups and inhabit tropical and subtropical waters. Males, as they mature, initially form bachelor groups but eventually become more socially isolated and more wide-ranging, inhabiting temperate and polar waters as well (Whitehead 2003). Sperm whales were commercially hunted in the Caribbean Sea by American whalers from sailing vessels until the early 1900s

Puerto Rico; U. S. Virgin Isl; S Stock

2010-01-01T23:59:59.000Z

213

Auditory system comparisons between sand cats and other felid species : acoustic input admittance of ears and auditory brainstem responses  

E-Print Network (OSTI)

The sand cat, one species of the cat family, is found only in deserts and has unusually large ear canals and middle-ear air cavities. Recent work has shown that sand cat ears absorb acoustic power at low frequencies (<1 ...

Chan, Howard F

2005-01-01T23:59:59.000Z

214

Live Fire Range Environmental Assessment  

SciTech Connect

The Central Training Academy (CTA) is a DOE Headquarters Organization located in Albuquerque, New Mexico, with the mission to effectively and efficiently educate and train personnel involved in the protection of vital national security interests of DOE. The CTA Live Fire Range (LFR), where most of the firearms and tactical training occurs, is a complex separate from the main campus. The purpose of the proposed action is to expand the LFR to allow more options of implementing required training. The Department of Energy has prepared this Environmental Assessment (EA) for the proposed construction and operation of an expanded Live Fire Range Facility at the Central Training Academy in Albuquerque, New Mexico. Based on the analysis in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, the preparation of an environmental impact statement is not required and DOE is issuing this Finding of No Significant Impact (FONSI).

None

1993-08-01T23:59:59.000Z

215

Production of Natural Gas and Fluid Flow in Tight Sand Reservoirs  

Science Conference Proceedings (OSTI)

This document reports progress of this research effort in identifying relationships and defining dependencies between macroscopic reservoir parameters strongly affected by microscopic flow dynamics and production well performance in tight gas sand reservoirs. These dependencies are investigated by identifying the main transport mechanisms at the pore scale that should affect fluids flow at the reservoir scale. A critical review of commercial reservoir simulators, used to predict tight sand gas reservoir, revealed that many are poor when used to model fluid flow through tight reservoirs. Conventional simulators ignore altogether or model incorrectly certain phenomena such as, Knudsen diffusion, electro-kinetic effects, ordinary diffusion mechanisms and water vaporization. We studied the effect of Knudsen's number in Klinkenberg's equation and evaluated the effect of different flow regimes on Klinkenberg's parameter b. We developed a model capable of explaining the pressure dependence of this parameter that has been experimentally observed, but not explained in the conventional formalisms. We demonstrated the relevance of this, so far ignored effect, in tight sands reservoir modeling. A 2-D numerical simulator based on equations that capture the above mentioned phenomena was developed. Dynamic implications of new equations are comprehensively discussed in our work and their relative contribution to the flow rate is evaluated. We performed several simulation sensitivity studies that evidenced that, in general terms, our formalism should be implemented in order to get more reliable tight sands gas reservoirs' predictions.

Maria Cecilia Bravo

2006-06-30T23:59:59.000Z

216

Production of Natural Gas and Fluid Flow in Tight Sand Reservoirs  

Science Conference Proceedings (OSTI)

This document reports progress of this research effort in identifying possible relationships and defining dependencies between macroscopic reservoir parameters strongly affected by microscopic flow dynamics and production well performance in tight gas sand reservoirs. Based on a critical review of the available literature, a better understanding of the main weaknesses of the current state of the art of modeling and simulation for tight sand reservoirs has been reached. Progress has been made in the development and implementation of a simple reservoir simulator that is still able to overcome some of the deficiencies detected. The simulator will be used to quantify the impact of microscopic phenomena in the macroscopic behavior of tight sand gas reservoirs. Phenomena such as, Knudsen diffusion, electro-kinetic effects, ordinary diffusion mechanisms and water vaporization are being considered as part of this study. To date, the adequate modeling of gas slippage in porous media has been determined to be of great relevance in order to explain unexpected fluid flow behavior in tight sand reservoirs.

Maria Cecilia Bravo; Mariano Gurfinkel

2005-06-30T23:59:59.000Z

217

The Effect of Temperature on the Absolute Permeability to Distilled Water of Unconsolidated Sand Cores  

SciTech Connect

The work presented herein is a study of the effect of temperature on the absolute permeability to distilled water of unconsolidated sandstones at one confining pressure. The absolute permeability to distilled water of Ottawa silica sand was not dependent on the temperature level.

Sageev, A.; Gobran, B.D.; Brigham, W.E.; Ramey, H.J. Jr.

1980-12-16T23:59:59.000Z

218

Integration of nuclear power with oil sands extraction projects in Canada  

E-Print Network (OSTI)

One of the largest oil reserves in the world is not in the Middle East or in Alaska, but in Canada. This fuel exists in the form of bitumen in Alberta's oil sands. While it takes a tremendous amount of energy to recover ...

Finan, Ashley (Ashley E.)

2007-01-01T23:59:59.000Z

219

Wilcox formation evaluation; Improved procedures for tight-gas-sand evaluation  

Science Conference Proceedings (OSTI)

This paper discusses risks in tight-gas-sand evaluation, reduced by defining relationships between pore geometry and critical water saturations. These results are integrated with log interpretation to derive an estimated kh that compares favorably with a true kh from production tests. These procedures are potentially applicable for evaluating other complex reservoirs.

Lewis, D.J.; Perrin, J.D. (BP Exploration Inc., Houston, TX (US))

1992-06-01T23:59:59.000Z

220

Ensemble-approaches for clustering health status of oil sand pumps F. Di Maio a  

E-Print Network (OSTI)

1 Ensemble-approaches for clustering health status of oil sand pumps F. Di Maio a , J. Hu b , P-of-the-practice entails oil pump failures being diagnosed by expert analysis of the parameter values measured during the monitoring time and their comparison with the nominal power curve of every oil pump: drawing the actual power

Paris-Sud XI, Université de

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Simulation of a cold heavy oil production with sand (CHOPS) separation system  

Science Conference Proceedings (OSTI)

A simulation of a heavy oil well site separation process was developed to test some of the requirements of operating on the North Slope of Alaska. This simulation used estimates of the dynamic proportions of oil, water and sand coming from the oil well ... Keywords: iThink™, CHOPS, North Slope, Alaska, continuous simulation, heavy oil

John Danielsen; David B. Hoffman

2009-03-01T23:59:59.000Z

222

Use of Brazilian sugarcane bagasse ash in concrete as sand replacement  

SciTech Connect

Sugarcane today plays a major role in the worldwide economy, and Brazil is the leading producer of sugar and alcohol, which are important international commodities. The production process generates bagasse as a waste, which is used as fuel to stoke boilers that produce steam for electricity cogeneration. The final product of this burning is residual sugarcane bagasse ash (SBA), which is normally used as fertilizer in sugarcane plantations. Ash stands out among agroindustrial wastes because it results from energy generating processes. Many types of ash do not have hydraulic or pozzolanic reactivity, but can be used in civil construction as inert materials. The present study used ash collected from four sugar mills in the region of Sao Carlos, SP, Brazil, which is one of the world's largest producers of sugarcane. The ash samples were subjected to chemical characterization, sieve analysis, determination of specific gravity, X-ray diffraction, scanning electron microscopy, and solubilization and leaching tests. Mortars and concretes with SBA as sand replacement were produced and tests were carried out: compressive strength, tensile strength and elastic modulus. The results indicated that the SBA samples presented physical properties similar to those of natural sand. Several heavy metals were found in the SBA samples, indicating the need to restrict its use as a fertilizer. The mortars produced with SBA in place of sand showed better mechanical results than the reference samples. SBA can be used as a partial substitute of sand in concretes made with cement slag-modified Portland cement.

Sales, Almir, E-mail: almir@ufscar.b [Department of Civil Engineering, UFSCar, Via Washington Luis, km 235, Monjolinho, 13565-905 Sao Carlos, SP (Brazil); Lima, Sofia Araujo, E-mail: sofiaalima@yahoo.com.b [Department of Civil Engineering, UFSCar, Via Washington Luis, km 235, Monjolinho, 13565-905 Sao Carlos, SP (Brazil)

2010-06-15T23:59:59.000Z

223

BIOTIGER, A NATURAL MICROBIAL PRODUCT FOR ENHANCED HYDROCARBON RECOVERY FROM OIL SANDS.  

SciTech Connect

BioTiger{trademark} is a unique microbial consortia that resulted from over 8 years of extensive microbiology screening and characterization of samples collected from a century-old Polish waste lagoon. BioTiger{trademark} shows rapid and complete degradation of aliphatic and aromatic hydrocarbons, produces novel surfactants, is tolerant of both chemical and metal toxicity and shows good activity at temperature and pH extremes. Although originally developed and used by the U.S. Department of Energy for bioremediation of oil-contaminated soils, recent efforts have proven that BioTiger{trademark} can also be used to increase hydrocarbon recovery from oil sands. This enhanced ex situ oil recovery process utilizes BioTiger{trademark} to optimize bitumen separation. A floatation test protocol with oil sands from Ft. McMurray, Canada was used for the BioTiger{trademark} evaluation. A comparison of hot water extraction/floatation test of the oil sands performed with BioTiger{trademark} demonstrated a 50% improvement in separation as measured by gravimetric analysis in 4 h and a five-fold increase at 25 hr. Since BioTiger{trademark} performs well at high temperatures and process engineering can enhance and sustain metabolic activity, it can be applied to enhance recovery of hydrocarbons from oil sands or other complex recalcitrant matrices.

Brigmon, R; Topher Berry, T; Whitney Jones, W; Charles Milliken, C

2008-05-27T23:59:59.000Z

224

COPIES: Iron Range Legislative Delegation  

E-Print Network (OSTI)

Dear Legislators: We are pleased to present the annual report on our research regarding the health status of taconite workers and Iron Range community air quality. This report, as in the past, details the progress made by the University of Minnesota School of Public Health and the Natural Resources Research Institute (NRRI) in all research areas, including occupational exposure, mortality and incidence studies, the respiratory health survey of taconite workers and spouses and the environmental study of airborne particles. In addition, this report contains specific information regarding the assessment of mesothelioma as it pertains to exposure to mineral fibers, referred to as elongate mineral particles (EMP). For this report, the EMP measurement is a standard technique that identifies those fibers (EMP) considered long (over 5 microns). Although the research team felt this was the most important exposure to be assessed with the cases of mesothelioma, in the next several months there will be additional analyses that may provide further insight, including exposure to short EMP, silica and respirable dust. A final report is planned for the end of the year when all components are expected to be completed.

Sen Tony Lourey; Rep Tim Mahoney; Rep Sheldon Johnson; Rep David Dill; Rep Mary Murphy; Sen Tom Bakk; Rep John Persell; Rep Tom Anzelc; Sen Tom Saxhaug; Rep Carly Melin; Rep Jason Metsa

2013-01-01T23:59:59.000Z

225

Modeling Electromagnetic Reflectivity of Agbabu Oil Sand from Hyperspectral Infrared Reflectance Spectra and Dielectric Properties at L-, C- and X-Band Frequencies  

Science Conference Proceedings (OSTI)

In this paper remote identification of oil sand reservoirs from synthetic aperture radar (SAR) is enhanced by accurate modeling of the electromagnetic (EM) reflectivity of Agbabu oil sands. This is demonstrated using a novel combination of hyperspectral ... Keywords: EM Reflectivity, Computer Simulation, Agbabu Oil Sand, Dielectric property, Petroleum Exploration

Maurice Ezeoke, Kenneth Tong

2013-06-01T23:59:59.000Z

226

Sandia National Laboratories Infor- Hybrid Wide Range Hybrid ...  

United States Department of Energy’s National Nuclear Security Administration under contact DE-AC04-94AL85000. SAND #2010-8682P . Author: Esparza, Jenna M

227

Long-Range Neutron Detection  

Science Conference Proceedings (OSTI)

A neutron detector designed for detecting neutron sources at distances of 50 to 100 m has been constructed and tested. This detector has a large surface area (1 m{sup 2}) to enhance detection efficiency, and it contains a collimator and shielding to achieve direction sensitivity and reduce background. An unusual feature of the detector is that it contains no added moderator, such as polyethylene, to moderate fast neutrons before they reach the {sup 3}He detector. As a result, the detector is sensitive mainly to thermal neutrons. The moderator-free design reduces the weight of the detector, making it more portable, and it also aids in achieving directional sensitivity and background reduction. Test results show that moderated fission-neutron sources of strength about 3 x 10{sup 5} n/s can be detected at a distance out to 70 m in a counting time of 1000 s. The best angular resolution of the detector is obtained at distances of 30 m or less. As the separation .distance between the source and detector increases, the contribution of scattered neutrons to the measured signal increases with a resultant decrease in the ability to detect the direction to a distant source. Applications for which the long-range detector appears to be suitable include detecting remote neutron sources (including sources in moving vehicles) and monitoring neutron storage vaults for the intrusion of humans and the effects they make on the detected neutron signal. Also, the detector can be used to measure waste for the presence of transuranic material in the presence of high gamma-ray background. A test with a neutron source (3 x 10{sup 5} n/s) in a vehicle showed that the detector could readily measure an increase in count rate at a distance of 10 m for vehicle speeds up to 35 mph (the highest speed tested). These results. indicate that the source should be detectable at this distance at speeds up to 55 mph.

AJ Peurrung; DC Stromswold; RR Hansen; PL Reeder; DS Barnett

1999-11-24T23:59:59.000Z

228

X-ray computed-tomography observations of water flow through anisotropic methane hydrate-bearing sand  

SciTech Connect

We used X-ray computed tomography (CT) to image and quantify the effect of a heterogeneous sand grain-size distribution on the formation and dissociation of methane hydrate, as well as the effect on water flow through the heterogeneous hydrate-bearing sand. A 28 cm long sand column was packed with several segments having vertical and horizontal layers with sands of different grain-size distributions. During the hydrate formation, water redistribution occurred. Observations of water flow through the hydrate-bearing sands showed that water was imbibed more readily into the fine sand, and that higher hydrate saturation increased water imbibition in the coarse sand due to increased capillary strength. Hydrate dissociation induced by depressurization resulted in different flow patterns with the different grain sizes and hydrate saturations, but the relationships between dissociation rates and the grain sizes could not be identified using the CT images. The formation, presence, and dissociation of hydrate in the pore space dramatically impact water saturation and flow in the system.

Seol, Yongkoo; Kneafsey, Timothy J.

2009-06-01T23:59:59.000Z

229

IA REP0 SAND85-2809 Unlimited Release UC-92A  

Office of Scientific and Technical Information (OSTI)

IA REP0 SAND85-2809 Unlimited Release UC-92A IA REP0 SAND85-2809 Unlimited Release UC-92A Printed July 1986 High Energy Gas Fracture Experiments in Fluid-Filled Boreholes-Potential Geothermal Application J. F. Cuderman, T. Y. Chu, J. Jung, R. D. Jacobson Prepared by Sandia National Laboratories Albuquerque, New Mexico 87 185 and Livermore, California 94550 for the United States Department of Energy under Contract DE-AC04-76DP00789 DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency Thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process

230

Microsoft Word - CX-Marion and Sand Springs Substation Towers Revised.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

KEC-4 KEC-4 SUBJECT: Environmental Clearance Memorandum Dave Tripp Project Manager - TEP-CSB-1 Proposed Action: Marion and Sand Springs Substations Radio Tower Projects Budget Information: Work Orders 00243411 and 00243190; Task 3 Categorical Exclusion Applied (from Subpart D, 10 C.F.R. Part 1021): B1.19 Siting, construction, and operation of microwave and radio communication towers and associated facilities... Location: Marion and Deschutes counties, Oregon Proposed by: Bonneville Power Administration (BPA) Description of the Proposed Action: BPA proposes to install new radio towers at the Marion Substation and Sand Springs Substation communication sites in Oregon. BPA must vacate radio frequencies in the 1710-1755MHz band to comply with a Federal law mandating reallocation of

231

Polymer flotation and activated carbon adsorption treatment for in situ tar sand process water  

SciTech Connect

Tar sand deposits in the United States are estimated to exceed thirty billion barrels, and offer long term potential for satisfying future energy needs. At present there is no commercial scale tar sand extraction industry in the United States, although several bench and pilot scale research projects have been completed. Three of the larger field scale experiments were completed by the Department of Energy (DOE) at a site near Vernal, Utah. The first two of these efforts involved in situ combustion while the third used steam drive. This paper reviews some of the flotation configurations which were used to generate a large (350 L) volume of treated effluent as well as describing some toxicology and analytical chemistry protocols used to characterize these fluids. Additional emphasis is placed upon a series of activated carbon adsorption experiments undertaken to detoxify the flotation effluents.

Mc Ternan, W.F.; Kocornik, D.J.; Nolan, B.T.; Blanton, W.E.; Boardman, G.D.

1985-01-01T23:59:59.000Z

232

True in-situ bed preparation: oil shale and tar sand  

SciTech Connect

In 1978, a detailed study was conducted to evaluate the status of the bed preparation technology that had been developed for true in-situ processing of oil shale. It was concluded that the two techniques which had received the bulk of the attention in prior field experimentation, namely the wellbore springing and hydraulic/explosive fracturing concepts, both had inherent traits which would prevent them from being useful in practical applications. In the current paper, the previous results are reviewed to determine whether or not they are also applicable to tar sand. The conclusion reached is that neither technique would be practical for preparing a tar sands deposit for in-situ processing.

Boade, R. R.

1980-01-01T23:59:59.000Z

233

Improvements in Sand Mold/Core Technology: Effects on Casting Finish  

SciTech Connect

In this study, the development and impact of density gradients on metal castings were investigated using sand molds/cores from both industry and from in-house production. In spite of the size of the castings market, almost no quantitative information about density variation within the molds/cores themselves is available. In particular, a predictive understanding of how structure and binder content/chemistry/mixing contribute to the final surface finish of these products does not exist. In this program we attempted to bridge this gap by working directly with domestic companies in examining the issues of surface finish and thermal reclamation costs resulting from the use of sand molds/cores. We show that these can be substantially reduced by the development of an in-depth understanding of density variations that correlate to surface finish. Our experimental tools and our experience with them made us uniquely qualified to achieve technical progress.

Prof. John J. Lannutti; Prof. Carroll E. Mobley

2005-08-30T23:59:59.000Z

234

Some Geotechnical Properties of Palm Biodiesel Contaminated Mining Sand and Weathered Granite Soil  

E-Print Network (OSTI)

Oil-pollution due to accidental during transportation or leakage from storage not only brings large damage to the environments, but it also affects the geotechnical properties of soil. Hence, an extensive laboratory testing program was carried out to investigate the geotechnical properties on palm biodiesel contaminated weathered granite soil and mining sand. A series of laboratory experiments has been carried out by using a direct simple shear device on clean and contaminated soil samples. The contaminated soil samples were mixed with palm biodiesel in the amount 5%, 10 % and 15 % by dry weight. The objective of this study is to determine the effects of palm biodiesel contamination on the mining sand and weathered granite soil samples. The overall results indicated decrease of shear strength with increasing palm biodiesel contents.

Yue Ling

2012-01-01T23:59:59.000Z

235

Numerical simulation of transient gas flow during underbalanced drilling into a gas sand  

Science Conference Proceedings (OSTI)

Shallow gas drilling has long been recognized as a serious problem in offshore operations. Low fracture gradients and shallow casing do not permit shutting- in the well. Computer simulations of gas kicks during drilling require accurate description of the gas flow rate from the formation into the wellbore. The problem is complicated by the fact that during drilling into a gas sand the effective wellbore area exposed to flow is continually changing until the formation has been completely drilled. This paper describes a numerical model developed to calculate gas flow into the wellbore while drilling underbalanced into a gas sand. A two-dimensional finite difference model of transient flow from the reservoir has been coupled with a one-dimensional finite element model of two-phase flow in the wellbore.

Berg, K.A.; Skalle, P. (Dept. of Petroleum Engineering, Univ. of Trondheim (NO)); Podio, A.L. (Dept. of Petroleum Engineering, Univ. of Texas at Austin, Austin, TX (US))

1991-01-01T23:59:59.000Z

236

Help:Range blocks | Open Energy Information  

Open Energy Info (EERE)

Range blocks Jump to: navigation, search Range blocks are technical restrictions applied through Special:Blockip to a group of IP addresses that prevent them from editing, creating...

237

Market model finds tight gas sands R and D offers most promise  

Science Conference Proceedings (OSTI)

Unconventional natural gas (UNG) - primarily tight gas sands - offers by far the largest opportunity for reducing gas costs between now and 2000, a team of researchers reported at the Sept. 1984 International Gas Research conference in Washington, DC. The promises of UNG R and D far outweigh those of synthetic natural gas (SNG), the researchers concluded, but stressed that SNG R and D should nonetheless continue - but with a different focus and changed performance goals.

Not Available

1984-09-17T23:59:59.000Z

238

Unconventional gas resources. [Eastern Gas Shales, Western Gas Sands, Coalbed Methane, Methane from Geopressured Systems  

DOE Green Energy (OSTI)

This document describes the program goals, research activities, and the role of the Federal Government in a strategic plan to reduce the uncertainties surrounding the reserve potential of the unconventional gas resources, namely, the Eastern Gas Shales, the Western Gas Sands, Coalbed Methane, and methane from Geopressured Aquifers. The intent is to provide a concise overview of the program and to identify the technical activities that must be completed in the successful achievement of the objectives.

Komar, C.A. (ed.)

1980-01-01T23:59:59.000Z

239

Application of gas flotation and foam separation for the treatment of tar-sand wastewaters  

SciTech Connect

A feasibility study was undertaken to evaluate the potential of air flotation and foam separation for the treatment of tar sand, steam generation waste waters collected following an in-situ experiment in Vernal, Utah. It was found that the process waters were not amenable to treatment by means of polymer-aided air flotation or foam separation. Suspended solids were readily removed by the process, but dissolved organic substances were not affected significantly.

Boardman, G.D.; Nolan, B.T.; VanLeigh, L.

1983-03-01T23:59:59.000Z

240

SANDS: A service-oriented architecture for clinical decision support in a National Health Information Network  

Science Conference Proceedings (OSTI)

In this paper, we describe and evaluate a new distributed architecture for clinical decision support called SANDS (Service-oriented Architecture for NHIN Decision Support), which leverages current health information exchange efforts and is based on the ... Keywords: Clinical decision making, Computer communication networks/standards, Computer-assisted decision support techniques, Computerized decision support systems, Hospital information systems, Information systems/organization & administration/standards, Medical records systems, Systems integration

Adam Wright; Dean F. Sittig

2008-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Quantitative Methods for Reservoir Characterization and Improved Recovery: Application to Heavy Oil Sands  

SciTech Connect

Improved prediction of interwell reservoir heterogeneity was needed to increase productivity and to reduce recovery cost for California's heavy oil sands, which contain approximately 2.3 billion barrels of remaining reserves in the Temblor Formation and in other formations of the San Joaquin Valley. This investigation involved application of advanced analytical property-distribution methods conditioned to continuous outcrop control for improved reservoir characterization and simulation.

Castle, J.W.; Molz, F.J.; Brame, S.E.; Falta, R.W.

2003-02-07T23:59:59.000Z

242

Quantitative Methods for Reservoir Characterization and Improved Recovery: Application to Heavy Oil Sands  

Science Conference Proceedings (OSTI)

Improved prediction of interwell reservoir heterogeneity is needed to increase productivity and to reduce recovery cost for California's heavy oil sands, which contain approximately 2.3 billion barrels of remaining reserves in the Temblor Formation and in other formations of the San Joaquin Valley. This investigation involved application of advanced analytical property-distribution methods conditioned to continuous outcrop control for improved reservoir characterization and simulation.

Castle, James W.; Molz, Fred J.

2003-02-07T23:59:59.000Z

243

Effect of temperature on wave velocities in sands and sandstones with heavy hydrocarbons  

SciTech Connect

A laboratory investigation was made of the effects of temperature on wave velocities in well cemented Massillon and Boise sandstones and unconsolidated Ottawa sand saturated with heavy hydrocarbons, as well as the dependence of compressional velocities in the hydrocarbons themselves as a function of temperature. The hydrocarbons selected as pore saturants were a commercial paraffin wax, 1-Eicosene, natural heavy crude, and natural tar. The experimental results show that the compressional wave velocities in the hydrocarbons decrease markedly with increasing temperature. In contrast wave velocities in the Massillon and Boise sandstones and unconsolidated Ottawa sand saturated with air or water decrease only little with increasing temperatures. The main reason for the large decreases in rocks with hydrocarbons is the melting of solid hydrocarbons, and high pore pressure. Thermal expansion of the saturants, and possibly thermal cracking of the heavy fractions and vaporization of the light fractions of the hydrocarbons may also contribute. The large decreases of the compressional and shear wave velocities in the hydrocarbon-saturated rocks and sands with temperature, suggest that seismic measurements such as used in seismology or borehole tomography may be very useful in detecting steam fronts in heavy hydrocarbon reservoirs undergoing steam flooding.

Wang, Z.; Nur, A.M.

1986-01-01T23:59:59.000Z

244

Oil shale, tar sand, coal research advanced exploratory process technology, jointly sponsored research  

SciTech Connect

Accomplishments for the past quarter are presented for the following five tasks: oil shale; tar sand; coal; advanced exploratory process technology; and jointly sponsored research. Oil shale research covers oil shale process studies. Tar sand research is on process development of Recycle Oil Pyrolysis and Extraction (ROPE) Process. Coal research covers: coal combustion; integrated coal processing concepts; and solid waste management. Advanced exploratory process technology includes: advanced process concepts;advanced mitigation concepts; and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; CROW field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; PGI demonstration project; operation and evaluation of the CO[sub 2] HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesaverde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced oil recovery techniques; surface process study for oil recovery using a thermal extraction process; NMR analysis of samples from the ocean drilling program; in situ treatment of manufactured gas plant contaminated soils demonstration program; and solid state NMR analysis of naturally and artificially matured kerogens.

Speight, J.G.

1992-01-01T23:59:59.000Z

245

Diamonds in the rough: identification of individual napthenic acids in oil sands process water  

Science Conference Proceedings (OSTI)

Expansion of the oil sands industry of Canada has seen a concomitant increase in the amount of process water produced and stored in large lagoons known as tailings ponds. Concerns have been raised, particularly about the toxic complex mixtures of water-soluble naphthenic acids (NA) in the process water. To date, no individual NA have been identified, despite numerous attempts, and while the toxicity of broad classes of acids is of interest, toxicity is often structure-specific, so identification of individual acids may also be very important. The chromatographic resolution and mass spectral identification of some individual NA from oil sands process water is described. The authors concluded that the presence of tricyclic diamondoid acids, never before even considered as NA, suggests an unprecedented degree of biodegradation of some of the oil in the oil sands. The identifications reported should now be followed by quantitative studies, and these used to direct toxicity assays of relevant NA and the method used to identify further NA to establish which, or whether all NA, are toxic. The two-dimensional comprehensive gas chromatography-mass spectrometry method described may also be important for helping to better focus reclamation/remediation strategies for NA as well as in facilitating the identification of the sources of NA in contaminated surface waters (auth)

Rowland, Steven J.; Scarlett, Alan G.; Jones, David; West, Charles E. (Petroleum and Environmental Geochemistry Group, Biogeochemistry Research Centre, University of Plymouth (United Kingdom)); Frank, Richard A. (Aquatic Ecosystems Protection Research Division-Water Science and Technology Directorate, Environment Canada, Burlington, Ontario (Canada)

2011-03-10T23:59:59.000Z

246

Oil shale, tar sand, coal research, advanced exploratory process technology jointly sponsored research  

SciTech Connect

Accomplishments for the quarter are presented for the following areas of research: oil shale, tar sand, coal, advanced exploratory process technology, and jointly sponsored research. Oil shale research includes; oil shale process studies, environmental base studies for oil shale, and miscellaneous basic concept studies. Tar sand research covers process development. Coal research includes; underground coal gasification, coal combustion, integrated coal processing concepts, and solid waste management. Advanced exploratory process technology includes; advanced process concepts, advanced mitigation concepts, and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO[sub 2] HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesa Verde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced recovery techniques; and menu driven access to the WDEQ Hydrologic Data Management Systems.

1992-01-01T23:59:59.000Z

247

Global Sea Level Stabilization-Sand Dune Fixation: A Solar-powered Sahara Seawater Textile Pipeline  

E-Print Network (OSTI)

Could anthropogenic saturation with pumped seawater of the porous ground of active sand dune fields in major deserts (e.g., the westernmost Sahara) cause a beneficial reduction of global sea level? Seawater extraction from the ocean, and its deposition on deserted sand dune fields in Mauritania and elsewhere via a Solar-powered Seawater Textile Pipeline (SSTP) can thwart the postulated future global sea level. Thus, Macro-engineering offers an additional cure for anticipated coastal change, driven by global sea level rise, that could supplement, or substitute for (1) stabilizing the shoreline with costly defensive public works (armoring macroprojects) and (2) permanent retreat from the existing shoreline (real and capital property abandonment). We propose Macro-engineering use tactical technologies that sculpt and vegetate barren near-coast sand dune fields with seawater, seawater that would otherwise, as commonly postulated, enlarge Earth seascape area! Our Macro-engineering speculation blends eremology with hydrogeology and some hydromancy. We estimate its cost at 1 billion dollars - about 0.01 per sent of the USA 2007 Gross Domestic Product.

Viorel Badescu; Richard B. Cathcart; Alexander A. Bolonkin

2007-07-21T23:59:59.000Z

248

Western Gas Sands Subprogram. Status report, October-November-December 1982  

Science Conference Proceedings (OSTI)

The progress during October, November and December 1982 of government-sponsored projects to increase gas production from low permeability gas sands of the Western United States, is summarized in this edition of the Western Gas Sands Subprogram (WGSS) Quarterly Status Report. During the quarter, major changes were made in the management of the subprogram. Personnel in the Division of Petroleum Projects Management at the Morgantown Energy Technology Center (METC) assumed the role of management for the Western Gas Sands Subprogram that had been performed by the Bartlesville Energy Technology Center (BETC). BETC continued in-house research on the fluid and proppant problems of fracture conductivity, and management of the Multi-Well Experiment (MWX). Owing to economic constraints, all efforts at the Sandia National Laboratory that were not directly related to the performance of MWX were terminated. The projects at the Lawrence Livermore National Laboratory and the Los Alamos National Laboratory were reduced by approximately 50 percent. The efforts at the USGS were reduced by 70 percent. Significant progress was made in the MWX project. Both the Upper and Lower Cozzette zones were production tested. Interference tests run on the Upper Cozzette showed much higher in situ permeability than core and log analysis indicated. This higher permeability has been attributed to the natural fractures. The site was closed for the winter on December 22 and the test trailer moved to CER Corporation, Las Vegas, for maintenance and upgrading. 40 figures, 16 tables.

Crawley, A. (comp.)

1983-12-01T23:59:59.000Z

249

Pyrolysis of Sunnyside (Utah) tar sand: Characterization of volatile compound evolution  

DOE Green Energy (OSTI)

Sunnyside (Utah) tar sand was subjected to programmed temperature pyrolysis and the volatile products were detected by tandem on-line mass spectrometry (MS/MS) in real time analyses. A heating rate of 4/degree/C/min from room temperature to 900/degree/C was employed. Evolution of hydrogen, light hydrocarbons, nitrogen-, sulfur- and oxygen-containing compounds was monitored by MS or MS/MS detection. Evolution of volatile organic compounds occurred in two regimes: 1) low temperature (maximum evolution at 150 to 175/degree C), corresponding to entrained organics, and 2) high temperature (maximum evolution at 440 to 460/degreeC), corresponding to cracking of large organic components. Pyrolysis yields were dominated by the evolution of light hydrocarbons. Alkanes and alkenes of two carbons and higher had temperatures of maximum evolution at approximately 440/degree/C, and methane at approximately 474/degree/C. Aromatic hydrocarbons had temperatures of maximum evolution slightly higher, at approximately 450/degree/C. In general, H/sub2/, CO, and CO/sub2/ exhibited evolution associated with hydrocarbon cracking reactions, and high temperature evolution associated with mineral decomposition, the water-gas shift reaction, and gasification reactions. Compared to other domestic tar sands, the gas evolution relected more mineral decomposition character for Sunnyside tar sand. 26 refs., 6 figs., 3 tabs.

Reynolds, J.G.; Crawford, R.W.

1988-06-01T23:59:59.000Z

250

Composition of modern sand from the Sierra Nevada, California, USA: Implications for actualistic petrofacies of continental-margin magmatic arcs  

E-Print Network (OSTI)

modern and ancient source rocks: Geology, v. 18, p. 733–736.sand composition and source-rock type, and the secondaryrock types, including Paleozoic and Mesozoic metamorphic terranes, and Cenozoic volcanic cover, is a source

Ingersoll, Raymond V.; Eastmond, Daniel J.

2007-01-01T23:59:59.000Z

251

Improving both bond strength and corrosion resistance of steel rebar in concrete by water immersion or sand blasting of rebar  

Science Conference Proceedings (OSTI)

Water immersion (2 days) and sand blasting were similarly effective for treating steel rebars for the purpose of improvement steel-concrete bond strength and corrosion resistance of steel in concrete. The increase in bond strength is due to surface roughening in the case of sand blasting and the presence of a surface layer in the case of water immersion. The increase in corrosion resistance is due to the surface uniformity rendered by either treatment.

Hou, J.; Fu, X.; Chung, D.D.L. [State Univ. of New York, Buffalo, NY (United States). Composite Materials Research Lab.

1997-05-01T23:59:59.000Z

252

Assessment of environmental health and safety issues associated with the commercialization of unconventional gas recovery: Tight Western Sands  

SciTech Connect

Results of a study to identify and evaluate potential public health and safety problems and the potential environmental impacts from recovery of natural gas from Tight Western Sands are reported. A brief discussion of economic and technical constraints to development of this resource is also presented to place the environmental and safety issues in perspective. A description of the resource base, recovery techniques, and possible environmental effects associated with tight gas sands is presented.

Riedel, E.F.; Cowan, C.E.; McLaughlin, T.J.

1980-02-01T23:59:59.000Z

253

Medium- and Long-Range Forecasting  

Science Conference Proceedings (OSTI)

In contrast to short and extended range forecasts, predictions for periods beyond 5 days use time-averaged, midtropospheric height fields as their primary guidance. As time ranges are increased to 3O- and 90-day outlooks, guidance increasingly ...

A. James Wagner

1989-09-01T23:59:59.000Z

254

Class I cultural resource overview for oil shale and tar sands areas in Colorado, Utah and Wyoming.  

Science Conference Proceedings (OSTI)

In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the 'Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005', Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. The Bureau of Land Management (BLM) is developing a Programmatic Environmental Impact Statement (PEIS) to evaluate alternatives for establishing commercial oil shale and tar sands leasing programs in Colorado, Wyoming, and Utah. This PEIS evaluates the potential impacts of alternatives identifying BLM-administered lands as available for application for commercial leasing of oil shale resources within the three states and of tar sands resources within Utah. The scope of the analysis of the PEIS also includes an assessment of the potential effects of future commercial leasing. This Class I cultural resources study is in support of the Draft Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and Programmatic Environmental Impact Statement and is an attempt to synthesize archaeological data covering the most geologically prospective lands for oil shale and tar sands in Colorado, Utah, and Wyoming. This report is based solely on geographic information system (GIS) data held by the Colorado, Utah, and Wyoming State Historic Preservation Offices (SHPOs). The GIS data include the information that the BLM has provided to the SHPOs. The primary purpose of the Class I cultural resources overview is to provide information on the affected environment for the PEIS. Furthermore, this report provides recommendations to support planning decisions and the management of cultural resources that could be impacted by future oil shale and tar sands resource development.

O'Rourke, D.; Kullen, D.; Gierek, L.; Wescott, K.; Greby, M.; Anast, G.; Nesta, M.; Walston, L.; Tate, R.; Azzarello, A.; Vinikour, B.; Van Lonkhuyzen, B.; Quinn, J.; Yuen, R.; Environmental Science Division

2007-11-01T23:59:59.000Z

255

Seismic amplitude and coherency response of channel sand, offshore Louisiana, Gulf of Mexico  

E-Print Network (OSTI)

Geological drilling hazards are a major concern in the ics. drilling and development of offshore reservoirs. Some of these hazards may display high amplitudes on seismic profiles and some may be associated with stratigraphic features. Seismic amplitude anomalies associated with channel sand deposits may indicate potential accumulations of hydrocarbons in reservoirs. However, shallow hydrocarbon accumulations are rarely of production size. More often, they are potential geological drilling hazards that could inhibit the development of petroleum resources from deeper hydrocarbon-bearing layers. Traditionally, existing and potential geologic hazards are identified by interpretation of high-resolution site survey data, acquired specifically for drilling hazard delineation. This paper describes a new technique for drilling hazard identification using a conventional 3D seismic amplitude dataset. An event coherence calculation program is applied to a 3D seismic dataset to derive seismic attributes sufficient to highlight structural and stratigraphic discontinuities in the area. A resultant 3D difference cube is used to establish fault framework and to detect spatial distribution of channel deposits in the area and their geometries. Superposition of the difference cube on seismic amplitude data allows simultaneous display of structural and stratigraphic discontinuities and reflectivity information. Therefore, it is used for the delineation of channels, which show anomalous amplitudes, identification of their dimensions and spatial locations, and implication of gas-charged sand distribution within the detected channel. The paper gives a detailed description of a workflow, which was found sufficient for delineation of likely gas-charged sand channels, and discusses the ways to adjust the proposed workbox to specific objectives.

Fischer, Elena Mikhaylovna

1999-01-01T23:59:59.000Z

256

Effects of Sand on the Components and Performance of Electric Submersible Pumps  

E-Print Network (OSTI)

The increasing world demand for oil has pushed oil companies to extract it from the ocean at extreme depths. With the increase in depth comes an increase in operation costs, especially the deep-sea equipment changeover cost. To be able to push the oil to the ocean surface, Electrical Submersible Pumps (ESPs) are commonly used as artificial lift. The changeover cost of these pumps in deep-water has been estimated to sometimes be as much as forty times the cost of a new pump. One common reason for the failure of ESPs is the erosion and abrasion created by the fine sands that seep through the gravel pack mesh in the well hole. These fine sand particles are most destructive to the bearings and bushings due to their capability to enter the clearances lubricated by the pumped fluid. Over time, the sustained abrasion and erosion in the different components of the ESP will affect the performance of the pump and could lead to its damage. This work describes the design, construction and evaluation of an erosion test rig built at the facilities of the Turbomachinery Laboratory in Texas A&M University. The test rig is capable of introducing 100 mesh (6 mil) sand into the flow loop, measure its concentration and separate it at the exit with minimal water loss. The pump under study is a Baker Hughes 10.25" WJE1000. The performance of the pump is described by measuring the head, flow rate, power and efficiency. The pump is equipped with accelerometers to detect the casing vibration as well as proximity probes in five locations along the pump to detect the internal vibrations of the shaft near the bearings as well as impeller radial movement. The baseline data, to be used for comparison with the worn out pump, has been shown and recommendations for the study method and operation of the rig are given.

Carvajal Diaz, Nicolas 1985-

2012-12-01T23:59:59.000Z

257

Rock matrix and fracture analysis of flow in western tight gas sands: 1986 annual report  

SciTech Connect

This report presents progress for the second year of a five-year project concerned with the pore structure and flow properties of low permeability gas sands. The main objective of work during the first year was to carry out advanced core analysis on cores recovered from the Multi-Well Field Experiment. In Phase 2, the properties of both fractured and non-fractured samples (hereafter referred to as matrix) have been studied. Special attention was given to the combined effect of overburden pressure and water saturation on gas flow. 11 refs., 18 figs., 4 tabs.

Morrow, N.R.; Buckley, J.S.; Cather, S.M.; Brower, K.R.; Dandge, V.; Graham, M.; Gonzales, B.

1987-02-01T23:59:59.000Z

258

In situ heat treatment from multiple layers of a tar sands formation  

DOE Patents (OSTI)

A method for treating a tar sands formation is disclosed. The method includes providing a drive fluid to a first hydrocarbon containing layer of the formation to mobilize at least some hydrocarbons in the first layer. At least some of the mobilized hydrocarbons are allowed to flow into a second hydrocarbon containing layer of the formation. Heat is provided to the second layer from one or more heaters located in the second layer. At least some hydrocarbons are produced from the second layer of the formation.

Vinegar, Harold J. (Bellaire, TX)

2010-11-30T23:59:59.000Z

259

Quantitative Methods for Reservoir Characterization and Improved Recovery: Application to Heavy Oil Sands  

SciTech Connect

The first twelve months of the project focused on collecting data for characterization and modeling. In addition, data from Coalinga Field was analyzed to define the fractal structure present in the data set. The following sections of the report parallel the first four subtasks of the investigation were: (1) Collect and Load Property Data from Temblor Outcrops in California, (2) Collect and Load Property Data from Temblor Reservoir Sands, West Coalinga Field, California, (3) Collect and Load Property Data from Continuous Upper Cretaceous Outcrops in Utah, and (4) Define Fractal Structure in the Data Sets and Apply to Generating Property Representations.

Castle, James W.; Molz, Fred J.

2001-11-29T23:59:59.000Z

260

Quantitative Methods for Reservoir Characterization and Improved Recovery: Application to Heavy Oil Sands  

Science Conference Proceedings (OSTI)

This project involved application of advanced analytical property-distribution methods conditioned to continuous outcrop control for improved reservoir characterization and simulation. The investigation was performed in collaboration with Chevron Production Company U.S.A. as an industrial partner, and incorporates data from the Temblor Formation in Chevron's West Coalinga Field, California. Improved prediction of interwell reservoir heterogeneity was needed to increase productivity and to reduce recovery cost for California's heavy oil sands, which contained approximately 2.3 billion barrels of remaining reserves in the Temblor Formation and in other formations of the San Joaquin Valley.

Castle, James W.; Molz, Fred W.; Bridges, Robert A.; Dinwiddie, Cynthia L.; Lorinovich, Caitlin J.; Lu, Silong

2003-02-07T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

The introduction of the microchanneling phenomenon to cyclic steam stimulation and its application to the numerical simulator (sand deformation concept)  

SciTech Connect

Historically, a vertical or horizontal fracture is believed to be a main recovery mechanism for a cyclic steam-injection process in unconsolidated oil sands. Most current computer models for the process are based on the fracture concept. With the postulated sand deformation concept, on the other hand, the injected fluid is able to penetrate the unconsolidated oil sand by creating microchannels. When the pore pressure is reduced during production, these secondary flow channels will collapse totally or partially. Condensed steam tends to sweep fluids where the bitumen had been heated and imparts mobility as a result of the injected hot fluid. Flow geometry of the new concept is described in this paper. The physical differences between the sand deformation zone and the no-deformation zone are also investigated. The three major differences between these two zones are porosity change, pressure level, and energy and flow characteristics resulting from the existence of microchannels. All these modifications were incorporated successfully into a conventional numerical thermal simulator. The new model provided an excellent match for all the field observations (steam-injection pressure, oil-and-water production rates, fluid production temperature, downhole production pressure, and salinity changes) of a steam-stimulated well in an unconsolidated oil sand. The study indicates that the most important phenomenon for in-situ recovery of bitumen is the one-way-valve effect of the microchannels, which are opened during injection and closed during production.

Ito, Y.

1984-08-01T23:59:59.000Z

262

Environmental, health, safety, and socioeconomic concerns associated with oil recovery from US tar-sand deposits: state-of-knowledge  

SciTech Connect

Tar-sand petroleum-extraction procedures undergoing field testing for possible commercial application in the US include both surface (above-ground) and in situ (underground) procedures. The surface tar-sand systems currently being field tested in the US are thermal decomposition processes (retorting), and suspension methods (solvent extraction). Underground bitumen extraction procedures that are also being field tested domestically are in situ combustion and steam-injection. Environmental, health, safety, and socioeconomic concerns associated with construction and operation of 20,000-bbl/d commercial tar-sand surface and in situ facilities have been estimated and are summarized in this report. The principal regulations that commercial tar-sand facilities will need to address are also discussed, and environmental control technologies are summarized and wherever possible, projected costs of emission controls are stated. Finally, the likelihood-of-occurrence of potential environmental, health, and safety problems that have been determined are reviewed, and from this information inference is made as to the environmental acceptability of technologically feasible 20,000-bbl/d commercial tar-sand oil-extraction procedures.

Daniels, J.I.; Anspaugh, L.R.; Ricker, Y.E.

1982-01-08T23:59:59.000Z

263

Oil shale, tar sand, coal research, advanced exploratory process technology, jointly sponsored research  

SciTech Connect

Progress made in five research programs is described. The subtasks in oil shale study include oil shale process studies and unconventional applications and markets for western oil shale.The tar sand study is on recycle oil pyrolysis and extraction (ROPE) process. Four tasks are described in coal research: underground coal gasification; coal combustion; integrated coal processing concepts; and sold waste management. Advanced exploratory process technology includes: advanced process concepts; advanced mitigation concepts; and oil and gas technology. Jointly sponsored research covers: organic and inorganic hazardous waste stabilization; CROW field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; PGI demonstration project; operation and evaluation of the CO[sub 2] HUFF-N-PUFF process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesaverde group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; shallow oil production using horizontal wells with enhanced oil recovery techniques; NMR analysis of sample from the ocean drilling program; and menu driven access to the WDEQ hydrologic data management system.

Not Available

1992-01-01T23:59:59.000Z

264

Developing a tight gas sand advisor for completion and stimulation in tight gas reservoirs worldwide  

E-Print Network (OSTI)

As the demand for energy worldwide increases, the oil and gas industry will need to increase recovery from unconventional gas reservoirs (UGR). UGRs include Tight Gas Sand (TGS), coalbed methane and gas shales. To economically produce UGRs, one must have adequate product price and one must use the most current technology. TGS reservoirs require stimulation as a part of the completion, so improvement of completion practices is very important. We did a thorough literature review to extract knowledge and experience about completion and stimulation technologies used in TGS reservoirs. We developed the principal design and two modules of a computer program called Tight Gas Sand Advisor (TGS Advisor), which can be used to assist engineers in making decisions while completing and stimulating TGS reservoirs. The modules include Perforation Selection and Proppant Selection. Based on input well/reservoir parameters these subroutines provide unambiguous recommendations concerning which perforation strategy(s) and what proppant(s) are applicable for a given well. The most crucial parameters from completion best-practices analyses and consultations with experts are built into TGS Advisor's logic, which mimics human expert's decision-making process. TGS Advisor's recommended procedures for successful completions will facilitate TGS development and improve economical performance of TGS reservoirs.

Bogatchev, Kirill Y

2007-12-01T23:59:59.000Z

265

Developing a tight gas sand advisor for completion and stimulation in tight gas reservoirs worldwide  

E-Print Network (OSTI)

As the demand for energy worldwide increases, the oil and gas industry will need to increase recovery from unconventional gas reservoirs (UGR). UGRs include Tight Gas Sand (TGS), coalbed methane and gas shales. To economically produce UGRs, one must have adequate product price and one must use the most current technology. TGS reservoirs require stimulation as a part of the completion, so improvement of completion practices is very important. We did a thorough literature review to extract knowledge and experience about completion and stimulation technologies used in TGS reservoirs. We developed the principal design and two modules of a computer program called Tight Gas Sand Advisor (TGS Advisor), which can be used to assist engineers in making decisions while completing and stimulating TGS reservoirs. The modules include Perforation Selection and Proppant Selection. Based on input well/reservoir parameters these subroutines provide unambiguous recommendations concerning which perforation strategy(s) and what proppant(s) are applicable for a given well. The most crucial parameters from completion best-practices analyses and consultations with experts are built into TGS Advisor’s logic, which mimics human expert’s decision-making process. TGS Advisor’s recommended procedures for successful completions will facilitate TGS development and improve economical performance of TGS reservoirs.

Bogatchev, Kirill Y.

2007-12-01T23:59:59.000Z

266

Flowsheet modifications for dissolution of sand, slag, and crucible residues in the F-canyon dissolvers  

Science Conference Proceedings (OSTI)

An initial flowsheet for the dissolution of sand, slag, and crucible (SS{ampersand}C) was developed for the F- Canyon dissolvers as an alternative to dissolution in FB-Line. In that flowsheet, the sand fines were separated from the slag chunks and crucible fragments. Those two SS{ampersand}C streams were packaged separately in mild-steel cans for dissolution in the 6.4D dissolver. Nuclear safety constraints limited the dissolver charge to approximately 350 grams of plutonium in two of the three wells of the dissolver insert and required 0.23M (molar) boron as a soluble neutron poison in the 9.3M nitric acid/0.013M fluoride dissolver solution. During the first dissolution of SS{ampersand}C fines, it became apparent that a significant amount of the plutonium charged to the 6.4D dissolver did not dissolve in the time predicted by previous laboratory experiments. The extended dissolution time was attributed to fluoride complexation by boron. An extensive research and development (R{ampersand}D) program was initiated to investigate the dissolution chemistry and the physical configuration of the dissolver insert to understand what flowsheet modifications were needed to achieve a viable dissolution process.

Rudisill, T.S.; Karraker, D.G.; Graham, F.R.

1997-12-01T23:59:59.000Z

267

Mineral Dissolution and Secondary Precipitation on Quartz Sand in Simulated Hanford Tank Solutions Affecting Subsurface Porosity  

SciTech Connect

Highly alkaline nuclear waste solutions have been released from underground nuclear waste storage tanks and pipelines into the vadose zone at the U.S. Department of Energy’s Hanford Site in Washington, causing mineral dissolution and re-precipitation upon contact with subsurface sediments. High pH caustic NaNO3 solutions with and without dissolved Al were reacted with quartz sand through flow-through columns stepwise at 45, 51, and 89°C to simulate possible reactions between leaked nuclear waste solution and primary subsurface mineral. Upon reaction, Si was released from the dissolution of quartz sand, and nitrate-cancrinite [Na8Si6Al6O24(NO3)2] precipitated on the quartz surface as a secondary mineral phase. Both steady-state dissolution and precipitation kinetics were quantified, and quartz dissolution apparent activation energy was determined. Mineral alteration through dissolution and precipitation processes results in pore volume and structure changes in the subsurface porous media. In this study, the column porosity increased up to 40.3% in the pure dissolution column when no dissolved Al was present in the leachate, whereas up to a 26.5% porosity decrease was found in columns where both dissolution and precipitation were observed because of the presence of Al in the input solution. The porosity change was also confirmed by calculation using the dissolution and precipitation rates and mineral volume changes.

Wang, Guohui; Um, Wooyong

2012-11-23T23:59:59.000Z

268

PowerPlex Fusion Product Size Ranges  

Science Conference Proceedings (OSTI)

The schematic diagram illustrates the fluorescent dye label color and relative PCR product size ranges for the various STR loci present in this ...

2012-12-03T23:59:59.000Z

269

HY RID WIDE RANGE TRANSIMPEDAN E AMPLIFIER  

TRANSIMPEDAN E AMPLIFIER TE HNOLOGY SUMMARY Many applications require wide range detection, where detector current is converted to a voltage by a

270

Physics Out Loud - Short-range Correlations  

NLE Websites -- All DOE Office Websites (Extended Search)

Quantum Chromodynamics (QCD) Previous Video (Quantum Chromodynamics (QCD)) Physics Out Loud Main Index Next Video (SRF Accelerator Cavities) SRF Accelerator Cavities Short-range...

271

Adaptive Range Counting and Other Frequency-Based Range Query Problems.  

E-Print Network (OSTI)

??We consider variations of range searching in which, given a query range, our goal is to compute some function based on frequencies of points that… (more)

Wilkinson, Bryan T.

2012-01-01T23:59:59.000Z

272

Reservoir characterization of the upper Merecure and lower Oficina Formations sands in the Leona Este Field, Eastern Venezuela Basin  

E-Print Network (OSTI)

The "S5", "T" and "U1" sands, traditionally described as part of the lower section of the "Oficina" Formation, and the "U2" sand, as part of the upper interval of the "Merecure" Formation, contain the largest oil remaining reserves of the Leona Este Field, which is located in the southern portion of the Eastern Venezuela Basin. Two or more of these reservoir sands, which are interbedded with shales, have been simultaneously produced pursuing an increase in the oil production rate, but an unexpected production performance was obtained: the accelerated and early increase of the water volume associated to the produced oil has caused the shut down of some wells in the Leona Este Field. In order to understand this productive performance and to re-evaluate the hydrocarbon potential of the study interval, it is important to describe these reservoirs in terms of their depositional origin and trap formation. An integrated reservoir model was constructed using all the available geological, geophysical and production data. The hydrocarbon trapping mechanism of each studied stratigraphic interval, traditionally known as the "S5", "TU", "TL", "U1U", "U1L", "U2U", "U2MA", "U2MB" and "U2L" sands, includes two components: ? Stratigraphic component: each stratigraphic interval presents one or more reservoir zones composed by sandy deposits that fill belts of stacked tidal-fluvial channels in a SSE-NNW trending tide-dominated estuarine system. In most intervals, these contemporaneous-in-deposition reservoir zones are not connected due to the lateral variation of facies present in the tide-dominated estuary. ? Structural component: northward dipping strata have been offset by a W-E trending major normal fault and secondary normal faults striking parallel to the major one. The major fault is the southern seal of the hydrocarbon traps. The most important prospects of the study interval are the reservoir zones 1 and 2 of the "U1L" sand, the reservoir zone 3 of the "U2MB" sand, and the "U1U" sand, which show more than 15 feet of average net sand thickness, and contain the largest volume of recoverable oil per reservoir zone in the Leona Este Field.

Flores Millan, Maria Carolina

2001-01-01T23:59:59.000Z

273

Molecular communication options for long range nanonetworks  

Science Conference Proceedings (OSTI)

Nanotechnology is an emerging field of science devoted to provide new opportunities in a vast range of areas. In this paper, different techniques are proposed to enable the long range interconnection of nano-machines, deployed over distances from a few ... Keywords: Axons and action potential, Fluorescent proteins, MOLED, Molecular communication, Nanonetworks

Lluís Parcerisa Giné; Ian F. Akyildiz

2009-11-01T23:59:59.000Z

274

Range search on multidimensional uncertain data  

Science Conference Proceedings (OSTI)

In an uncertain database, every object o is associated with a probability density function, which describes the likelihood that o appears at each position in a multidimensional workspace. This article studies two types of range retrieval ... Keywords: Uncertain databases, range search

Yufei Tao; Xiaokui Xiao; Reynold Cheng

2007-08-01T23:59:59.000Z

275

Pore-scale mechanisms of gas flow in tight sand reservoirs  

Science Conference Proceedings (OSTI)

Tight gas sands are unconventional hydrocarbon energy resource storing large volume of natural gas. Microscopy and 3D imaging of reservoir samples at different scales and resolutions provide insights into the coaredo not significantly smaller in size than conventional sandstones, the extremely dense grain packing makes the pore space tortuous, and the porosity is small. In some cases the inter-granular void space is presented by micron-scale slits, whose geometry requires imaging at submicron resolutions. Maximal Inscribed Spheres computations simulate different scenarios of capillary-equilibrium two-phase fluid displacement. For tight sands, the simulations predict an unusually low wetting fluid saturation threshold, at which the non-wetting phase becomes disconnected. Flow simulations in combination with Maximal Inscribed Spheres computations evaluate relative permeability curves. The computations show that at the threshold saturation, when the nonwetting fluid becomes disconnected, the flow of both fluids is practically blocked. The nonwetting phase is immobile due to the disconnectedness, while the permeability to the wetting phase remains essentially equal to zero due to the pore space geometry. This observation explains the Permeability Jail, which was defined earlier by others. The gas is trapped by capillarity, and the brine is immobile due to the dynamic effects. At the same time, in drainage, simulations predict that the mobility of at least one of the fluids is greater than zero at all saturations. A pore-scale model of gas condensate dropout predicts the rate to be proportional to the scalar product of the fluid velocity and pressure gradient. The narrowest constriction in the flow path is subject to the highest rate of condensation. The pore-scale model naturally upscales to the Panfilov's Darcy-scale model, which implies that the condensate dropout rate is proportional to the pressure gradient squared. Pressure gradient is the greatest near the matrix-fracture interface. The distinctive two-phase flow properties of tight sand imply that a small amount of gas condensate can seriously affect the recovery rate by blocking gas flow. Dry gas injection, pressure maintenance, or heating can help to preserve the mobility of gas phase. A small amount of water can increase the mobility of gas condensate.

Silin, D.; Kneafsey, T.J.; Ajo-Franklin, J.B.; Nico, P.

2010-11-30T23:59:59.000Z

276

Techniques for optically compressing light intensity ranges  

DOE Patents (OSTI)

A pin hole camera assembly for use in viewing an object having a relatively large light intensity range, for example a crucible containing molten uranium in an atomic vapor laser isotope separator (AVLIS) system is disclosed herein. The assembly includes means for optically compressing the light intensity range appearing at its input sufficient to make it receivable and decipherable by a standard video camera. A number of different means for compressing the intensity range are disclosed. These include the use of photogray glass, the use of a pair of interference filters, and the utilization of a new liquid crystal notch filter in combination with an interference filter.

Rushford, Michael C. (Livermore, CA)

1989-01-01T23:59:59.000Z

277

Techniques for optically compressing light intensity ranges  

DOE Patents (OSTI)

A pin hole camera assembly for use in viewing an object having a relatively large light intensity range, for example a crucible containing molten uranium in an atomic vapor laser isotope separator (AVLIS) system is disclosed herein. The assembly includes means for optically compressing the light intensity range appearing at its input sufficient to make it receivable and decipherable by a standard video camera. A number of different means for compressing the intensity range are disclosed. These include the use of photogray glass, the use of a pair of interference filters, and the utilization of a new liquid crystal notch filter in combination with an interference filter. 18 figs.

Rushford, M.C.

1989-03-28T23:59:59.000Z

278

NUREG/CR-6547 SAND97-2776 DOSFAC2 User's Guide  

Office of Scientific and Technical Information (OSTI)

547 547 SAND97-2776 DOSFAC2 User's Guide Prepared by M. L.Young/SNL D. Chanin/TE Sandia National Laboratories Technadyne Engineering Prepared for U . S . Nuclear Regulatory Commission AVAllABlLlTY NOTICE Availabiliiy o f Reference Materials Cied in NFlC Publications Most documents cited In NRC publications will be available from one of the following sources: 1. The NRC Public DoclJment Room. 2120 L Street, NW., Lower Level. Washington, DC 20555-0001 2. The Superintendent of Documents, U.S. Government Printing Office, P. 0. Box 37082, Washington, DC 20402-9328 3. Although the listing that follows represents the majority of documents cited in NRC publications, it is not in- tended to be exhaustive. The National Technical Information Service, Springfield, VA 22 161 -0002

279

Temperature effects on oil-water relative permeabilities for unconsolidated sands  

SciTech Connect

This study presents an experimental investigation of temperature effects on relative permeabilities of oil- water systems in unconsolidated sands. The fluids used in this study were refined mineral oil and distilled water. A rate sensitivity study was done on residual oil saturation and oil and water relative permeabilities. The temperature sensitivity study of relative permeabilities was conducted in 2 parts. The first was to investigate changes in residual oil saturation with temperature where the cores were 100% saturated with oil at the start of the waterflood. The second part continued the floods for a longer time until the water-cut was virtually 100%. Under these conditions, little change in residual oil saturation was observed with temperature. A study on viscous instabilities also was performed. This verified the existence of viscous fingers during waterflooding. It also was observed that tubing volume after the core could cause fingering, resulting in lower apparent breakthrough oil recoveries.

Sufi, A.H.

1983-03-01T23:59:59.000Z

280

Evolution of seismic velocities in heavy oil sand reservoirs during thermal recovery process  

E-Print Network (OSTI)

In thermally enhanced recovery processes like cyclic steam stimulation (CSS) or steam assisted gravity drainage (SAGD), continuous steam injection entails changes in pore fluid, pore pressure and temperature in the rock reservoir, that are most often unconsolidated or weakly consolidated sandstones. This in turn increases or decreases the effective stresses and changes the elastic properties of the rocks. Thermally enhanced recovery processes give rise to complex couplings. Numerical simulations have been carried out on a case study so as to provide an estimation of the evolution of pressure, temperature, pore fluid saturation, stress and strain in any zone located around the injector and producer wells. The approach of Ciz and Shapiro (2007) - an extension of the poroelastic theory of Biot-Gassmann applied to rock filled elastic material - has been used to model the velocity dispersion in the oil sand mass under different conditions of temperature and stress. A good agreement has been found between these pre...

Nauroy, Jean-François; Guy, N; Baroni, Axelle; Delage, Pierre; Mainguy, Marc; 10.2516/ogst/2012027

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Long range interactions in nanoscale science  

E-Print Network (OSTI)

Our understanding of the “long range” electrodynamic, electrostatic, and polar interactions that dominate the organization of small objects at separations beyond an interatomic bond length is reviewed. From this basic-forces ...

Rajter, Richard F.

282

Range resolution of unequal strength targets  

E-Print Network (OSTI)

This paper examines the problem of resolving targets whose amplitudes may differ. A common metric used for resolution that assumes targets of equal strength is modified for the subject scenario. An expression for range ...

Carlson, Blair D.

283

Underwater vehicle localization using range measurements  

E-Print Network (OSTI)

This thesis investigates the problem of cooperative navigation of autonomous marine vehicles using range-only acoustic measurements. We consider the use of a single maneuvering autonomous surface vehicle (ASV) to aid the ...

Papadopoulos, Ge?rgios

2010-01-01T23:59:59.000Z

284

Smart grid e PLC: TOA ranging.  

E-Print Network (OSTI)

??In questo lavoro vengono presentati alcuni standard PLC (PowerLine Communication) nell'ottica del loro utilizzo in applicazioni di ranging in piccole reti intelligenti (micro smart grid).… (more)

Danzi, Pietro

2012-01-01T23:59:59.000Z

285

Policy Analysis of Water Availability and Use Issues for Domestic Oil Shale and Oil Sands Development  

Science Conference Proceedings (OSTI)

Oil shale and oil sands resources located within the intermountain west represent a vast, and as of yet, commercially untapped source of energy. Development will require water, and demand for scarce water resources stands at the front of a long list of barriers to commercialization. Water requirements and the consequences of commercial development will depend on the number, size, and location of facilities, as well as the technologies employed to develop these unconventional fuels. While the details remain unclear, the implication is not – unconventional fuel development will increase demand for water in an arid region where demand for water often exceeds supply. Water demands in excess of supplies have long been the norm in the west, and for more than a century water has been apportioned on a first-come, first-served basis. Unconventional fuel developers who have not already secured water rights stand at the back of a long line and will need to obtain water from willing water purveyors. However, uncertainty regarding the nature and extent of some senior water claims combine with indeterminate interstate river management to cast a cloud over water resource allocation and management. Quantitative and qualitative water requirements associated with Endangered Species protection also stand as barriers to significant water development, and complex water quality regulations will apply to unconventional fuel development. Legal and political decisions can give shape to an indeterminate landscape. Settlement of Northern Ute reserved rights claims would help clarify the worth of existing water rights and viability of alternative sources of supply. Interstate apportionment of the White River would go a long way towards resolving water availability in downstream Utah. And energy policy clarification will help determine the role oil shale and oil sands will play in our nation’s future.

Ruple, John; Keiter, Robert

2010-12-31T23:59:59.000Z

286

After the fire is out: A post in-situ combustion audit, Upper Miocene deepwater sands, San Joaquin Valley, California  

SciTech Connect

An audit of small-scale, air in-situ combustion projects developed in the upper Miocene Monarch and Webster unconsolidated, arkosic sand reservoirs, Midway Sunset field, Kern County, California, demonstrates minor rock diagenesis. Burn distribution and progression is controlled by reservoir continuity, layering, and original permeability variations. Air in-situ combustion projects were operated between 1962 and 1976. Injected air drives a burning oil (coke) front through a reservoir reaching maximum temperatures of 650C. Dense new well control including 3,000 ft of core is part of a large steamdrive development. Fireflood-induced diagenesis was clearly visible in core. Altered zones include sands with reduced oil saturations, burn zones with remaining coke, and reddish (oxidized) zones with no hydrocarbons. Wireline log response in these zones have been highly modified. Detailed mapping by subzone using pre- and post-burn logs permits the determination of three-dimensional burn and reduced saturation geometries. Little rock alteration occurred in these sands. The only diagenesis of the sand fraction was to calcite grains, where oil/calcite reactions produced calcium sulfate rims and CO{sub 2} gas. X-ray diffraction of finer 'matrix' reveals no recrystallization of opal-CT, no irreversible collapse of smectite, and only minor removal of kaolinite. Partial dissolution of opal and zeolites was visible in SEM. This nonequilibrium mineral suite probably reflects kinetic control by grain size, protective grain coatings, and alteration time.

Eagan, J.M.; Barrett, M.L. (Mobil Exploration and Producing US, Bakersfield, CA (United States)); Soustek, P.G. (Mobil Exploration and Producing US, Denver, CO (United States))

1991-03-01T23:59:59.000Z

287

Comprehensive Study of the Reservoir Sand and Depositional Setting of Garden Banks Field 236, North-Central Gulf of Mexico  

E-Print Network (OSTI)

-Central Gulf of Mexico Sean O'Brien, M. Royhan Gani, and Abu K. M. Sarwar Department of Earth and Environmental in the northern Gulf of Mexico. Hydrocarbon explo- ration and production of these deposits has yielded one of the largest gas producing trends in the Gulf of Mexico continental shelf-slope break. Reservoir sands were

Gani, M. Royhan

288

Range Fuels Biorefinery Groundbreaking | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Range Fuels Biorefinery Groundbreaking Range Fuels Biorefinery Groundbreaking Range Fuels Biorefinery Groundbreaking November 6, 2007 - 5:00pm Addthis Remarks as Prepared for Secretary Bodman Thank you. And let me say how much it means to have my old friend Vinodh here to introduce me. You are a true pioneer in this industry. I also want to thank Mitch for asking me to be here. It's good to see Tom Dorr from the U.S. Department of Agriculture, our partner in so much of the federal government's biomass research and development and deployment efforts. Gov. Perdue, as always, it's great to be in Georgia and to see the progress occurring here under your leadership. I want to reaffirm our support for governors and state legislators who exhibit the kind of leadership you've shown in developing America's new energy future.

289

Range conditions for a spherical mean transform  

E-Print Network (OSTI)

The paper is devoted to the range description of the Radon type transform that averages a function over all spheres centered on a given sphere. Such transforms arise naturally in thermoacoustic tomography, a novel method of medical imaging. Range descriptions have recently been obtained for such transforms, and consisted of smoothness and support conditions, moment conditions, and some additional orthogonality conditions of spectral nature. It has been noticed that in odd dimensions, surprisingly, the moment conditions are superfluous and can be eliminated. It is shown in this text that in fact the same happens in any dimension.

Mark Agranovsky; David Finch; Peter Kuchment

2009-02-25T23:59:59.000Z

290

Gravitomagnetism and the Earth-Mercury range  

E-Print Network (OSTI)

We numerically work out the impact of the general relativistic Lense-Thirring effect on the Earth-Mercury range caused by the gravitomagnetic field of the rotating Sun. The peak-to peak nominal amplitude of the resulting time-varying signal amounts to 1.75 10^1 m over a temporal interval 2 yr. Future interplanetary laser ranging facilities should reach a cm-level in ranging to Mercury over comparable timescales; for example, the BepiColombo mission, to be launched in 2014, should reach a 4.5 - 10 cm level over 1 - 8 yr. We looked also at other Newtonian (solar quadrupole mass moment, ring of the minor asteroids, Ceres, Pallas, Vesta, Trans-Neptunian Objects) and post-Newtonian (gravitoelectric Schwarzschild solar field) dynamical effects on the Earth-Mercury range. They act as sources of systematic errors for the Lense-Thirring signal which, in turn, if not properly modeled, may bias the recovery of some key parameters of such other dynamical features of motion. Their nominal peak-to-peak amplitudes are as large as 4 10^5 m (Schwarzschild), 3 10^2 m (Sun's quadrupole), 8 10^1 m (Ceres, Pallas, Vesta), 4 m (ring of minor asteroids), 8 10^-1 m (Trans-Neptunian Objects). Their temporal patterns are different with respect to that of the gravitomagnetic signal.

Lorenzo Iorio

2010-02-01T23:59:59.000Z

291

High-Dynamic-Range Imaging for artists  

Science Conference Proceedings (OSTI)

An introduction and overview of the practical applications and uses of high-dynamic-range imaging (HDRI) from a production point of view. The course begins with a brief overview of HDRI and pre-production, production, and post-production techniques. ...

Kirt Witte

2009-12-01T23:59:59.000Z

292

Secure multidimensional range queries in sensor networks  

Science Conference Proceedings (OSTI)

Most future large-scale sensor networks are expected to follow a two-tier architecture which consists of resource-rich master nodes at the upper tier and resource-poor sensor nodes at the lower tier. Sensor nodes submit data to nearby master nodes which ... Keywords: multidimensional range query, security, sensor networks,

Rui Zhang; Jing Shi; Yanchao Zhang

2009-05-01T23:59:59.000Z

293

Some Recent Long-Range Diffusion Observations  

Science Conference Proceedings (OSTI)

Recent atmospheric cloud-spreading (relative diffusion) data from a variety of sources are combined to show that the horizontal spreading rate is approximately linear over a time range from 1 to 10 or more hours (20?200 or more km) of downwind ...

F. A. Gifford

1995-07-01T23:59:59.000Z

294

Compact range for variable-zone measurements  

DOE Patents (OSTI)

A compact range for testing antennas or radar targets includes a source for directing energy along a feedline toward a parabolic reflector. The reflected wave is a spherical wave with a radius dependent on the distance of the source from the focal point of the reflector. 2 figs.

Burnside, W.D.; Rudduck, R.C.; Yu, J.S.

1987-02-27T23:59:59.000Z

295

Compact range for variable-zone measurements  

DOE Patents (OSTI)

A compact range for testing antennas or radar targets includes a source for directing energy along a feedline toward a parabolic reflector. The reflected wave is a spherical wave with a radius dependent on the distance of the source from the focal point of the reflector.

Burnside, Walter D. (Columbus, OH); Rudduck, Roger C. (Columbus, OH); Yu, Jiunn S. (Albuquerque, NM)

1988-01-01T23:59:59.000Z

296

Seasonal Variation in Daily Temperature Ranges  

Science Conference Proceedings (OSTI)

Abrupt spring and autumnal changes in the daily temperature range, from low winter values to higher nonwinter values, were noted in the Minneapolis-St. Paul temperature record. Since this feature was even more evident in five rural and small town ...

David L. Ruschy; Donald G. Baker; Richard H. Skaggs

1991-12-01T23:59:59.000Z

297

Likely Ranges of Climate Change in Bolivia  

Science Conference Proceedings (OSTI)

Bolivia is facing numerous climate-related threats, ranging from water scarcity due to rapidly retreating glaciers in the Andes to a partial loss of the Amazon forest in the lowlands. To assess what changes in climate may be expected in the future,...

Christian Seiler; Ronald W. A. Hutjes; Pavel Kabat

2013-06-01T23:59:59.000Z

298

Evaluation of water production in tight gas sands in the Cotton Valley formation in the Caspiana, Elm Grove and Frierson fields  

E-Print Network (OSTI)

Normally in tight gas sands, water production is not a problem but in such low permeability reservoirs it is difficult to produce gas at commercial flow rates. Since water is more viscous than gas, very little water is normally produced in low permeability reservoirs. The production of large volumes of water from tight gas sands, say 50-100 bbls of water per MMcf of gas constitutes a cause for concern. High water production (>200 bbls of water per MMcf of gas) has been observed in the low permeability Cotton Valley sands in the Caspiana, Elm Grove and Frierson fields of North Louisiana. This research evaluates water production in the above tight gas sands using field data provided by Matador Resource, a member of the Crisman Institute in Texas A&M university. The research is aimed at providing realistic reservoir scenarios of excess water production in tight gas sands. Log analysis, property trends and well production profiles have been used in establishing the different scenarios. The reservoir simulation results and the production trends show a possible water source from faults and fractures connecting the Travis Peak/Smackover sands to the Cotton Valley sands. An improved understanding of the reservoir would help in further field development.

Ozobeme, Charles Chinedu

2006-12-01T23:59:59.000Z

299

Facies and architecture of deep-water Sandstone lobes: Comparison of a shale-rich and a sand-rich system  

SciTech Connect

Two different foreland-basin deep-water sandstone systems have been studied for reservoir characterization purposes: the Broto lobes of the Eocene Hecho group, spain, and two sand bodies of the Oligocene-Miocene Arakintos Sandstone, Greece. The shale-rich Broto lobes are characterized by distinct vertical developments in terms of facies and expression of heterogeneity. Bed-thickness trends, lateral extent of sand beds, and facies variability are related to overall sand/shale ratio. A feature common to most of the sandstone packages is the occurrence of a basal slump and/or pebbly mudstone. The dominant sediment source is considered fluvial. Variation in sand quality within and between lobes is high. Deposition is considered to be strongly controlled by tectonics. The sand-rich Arakintos Sandstone consists of massive and pebbly sandstones, forming thick, sandy sheets alternating with relatively coarse-grained, thin-bedded turbidites. Facies, geometries, vertical organization, and the relation between grain size and bed thickness indicate a constrained development of the lobes, partly influenced by preexisting topography. A coastal sediment source is inferred. Little variation exists in sand quality within and between the lobes. The overall regularity in terms of facies, and the absence of slumps, suggest that fluctuations in relative sea level may have formed a major control on deposition. The two lobe systems illustrate the effect of tectonics, sediment type, topographic confinement, and possible sea level on facies and sand body architecture of deep-water sandstone lobes.

Schuppers, J.D. (Delft Univ. of Technology (Netherlands))

1993-09-01T23:59:59.000Z

300

Method and apparatus for coherent burst ranging  

DOE Patents (OSTI)

A high resolution ranging method is described utilizing a novel modulated waveform, hereafter referred to as coherent burst modulation. In the coherent burst method, high frequency modulation of an acoustic or electromagnetic transmitter, such as a laser, is performed at a modulation frequency. This modulation frequency is transmitted quasi-continuously in the form of interrupted bursts of radiation. Energy from the transmitter is directed onto a target, interacts with the target, and the returning energy is collected. The encoded burst pattern contained in the collected return signal is detected coherently by a receiver that is tuned so as to be principally sensitive to the modulation frequency. The receiver signal is processed to determine target range using both time-of-flight of the burst envelope and phase shift of the high frequency modulation. This approach effectively decouples the maximum unambiguous range and range resolution relationship of earlier methods, thereby allowing high precision ranging to be conducted at arbitrarily long distances using at least one burst of encoded energy. The use of a receiver tuned to the high frequency modulation contained within the coherent burst vastly improves both sensitivity in the detection of the target return signal and rejection of background interferences, such as ambient acoustic or electromagnetic noise. Simultaneous transmission at several energies (or wavelengths) is possible by encoding each energy with a separate modulation frequency or pattern; electronic demodulation at the receiver allows the return pattern for each energy to be monitored independently. Radial velocity of a target can also be determined by monitoring change in phase shift of the return signal as a function of time. 12 figs.

Wachter, E.A.; Fisher, W.G.

1998-04-28T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Method and apparatus for coherent burst ranging  

DOE Patents (OSTI)

A high resolution ranging method is described utilizing a novel modulated waveform, hereafter referred to as coherent burst modulation. In the coherent burst method, high frequency modulation of an acoustic or electromagnetic transmitter, such as a laser, is performed at a modulation frequency. This modulation frequency is transmitted quasi-continuously in the form of interrupted bursts of radiation. Energy from the transmitter is directed onto a target, interacts with the target, and the returning energy is collected. The encoded burst pattern contained in the collected return signal is detected coherently by a receiver that is tuned so as to be principally sensitive to the modulation frequency. The receiver signal is processed to determine target range using both time-of-flight of the burst envelope and phase shift of the high frequency modulation. This approach effectively decouples the maximum unambiguous range and range resolution relationship of earlier methods, thereby allowing high precision ranging to be conducted at arbitrarily long distances using at least one burst of encoded energy. The use of a receiver tuned to the high frequency modulation contained within the coherent burst vastly improves both sensitivity in the detection of the target return signal and rejection of background interferences, such as ambient acoustic or electromagnetic noise. Simultaneous transmission at several energies (or wavelengths) is possible by encoding each energy with a separate modulation frequency or pattern; electronic demodulation at the receiver allows the return pattern for each energy to be monitored independently. Radial velocity of a target can also be determined by monitoring change in phase shift of the return signal as a function of time.

Wachter, Eric A. (138 Bay Path Dr., Oak Ridge, TN 37830); Fisher, Walter G. (8514 Carl Valentine, Knoxville, TN 37931)

1998-01-01T23:59:59.000Z

302

Ecological Consequences of Landscape Fragmentation on the Lizard Community in the Mescalero-Monahans Shinnery Sands  

E-Print Network (OSTI)

Landscape fragmentation poses a major threat to biodiversity world-wide. The goal of my dissertation research was to determine the effects of landscape fragmentation on a lizard community in the Mescalero-Monahans shinnery sands, New Mexico and the extent to which conservation efforts might protect biodiversity in this ecosystem. My research relied heavily on data collected from a large-scale spatially-replicated comparative study. The purpose of this study was to evaluate the impacts of landscape fragmentation as a result of oil and gas development on the dunes sagebrush lizard (Sceloporus arenicolus). Results from analysis of lizard community structure indicate that fragmented sites are less diverse than non-fragmented sites. In particular, two species are found in lower density and occupancy in the fragmented locations (Holbrookia maculata and Sceloporus arenicolus). Analysis of landscape configuration at the scale of a trapping grid indicated that sand dune blowout shape and size differed between fragmented and non-fragmented locations. Differences in landscape pattern were associated with reduced lizard diversity. Because of this association between lower diversity and altered landscape pattern, extensive alterations to landscape pattern may cause disassembly at the ecosystem level. The maintenance of existing landscape pattern may be important to the maintenance of diversity in this ecosystem. Evaluations of habitat use patterns of the lizards in this community demonstrate that a few species have narrow preferences for certain habitats. In particular, H. maculata, Phrynosoma cornutum, and S. arenicolus all demonstrated narrow habitat use patterns. Effect size of fragmentation for each species indicated that the same three species showed a large effect when comparing their average abundances between fragmented and non-fragmented locations. Thus species that are most likely to benefit or be harmed by landscape fragmentation are those with the most specific habitat requirements. Umbrella species represent one of many approaches to conservation using surrogate species. I used data on ants, beetles, small mammals, lizards, and endemic species to test the use of the dunes sagebrush lizard (Sceloporus arenicolus) as an umbrella for endemism and biodiversity of the Mescalero-Monahans shinnery sands ecosystem. I applied a comparative approach at three spatial scales to examine how conservation practices at different scales may affect biodiversity and endemism in this ecosystem. At the largest scale, the frequency of occurrence for endemic species increased though no other patterns emerged because S. arenicolus was present at all sites and there were no relationships between relative abundances of S. arenicolus and the other taxonomic groups. At the smallest scale, both beetle species richness, diversity, and endemic species richness were higher in the presence of S. arenicolus. To protect biodiversity in this ecosystem, conservation efforts should focus on protection at the scale of the species distribution rather than on the small-scale placement of individual well pads.

Leavitt, Daniel 1979-

2012-12-01T23:59:59.000Z

303

QUANTITATIVE METHODS FOR RESERVOIR CHARACTERIZATION AND IMPROVED RECOVERY: APPLICATION TO HEAVY OIL SANDS  

SciTech Connect

Improved prediction of interwell reservoir heterogeneity has the potential to increase productivity and to reduce recovery cost for California's heavy oil sands, which contain approximately 2.3 billion barrels of remaining reserves in the Temblor Formation and in other formations of the San Joaquin Valley. This investigation involves application of advanced analytical property-distribution methods conditioned to continuous outcrop control for improved reservoir characterization and simulation, particularly in heavy oil sands. The investigation was performed in collaboration with Chevron Production Company U.S.A. as an industrial partner, and incorporates data from the Temblor Formation in Chevron's West Coalinga Field. Observations of lateral variability and vertical sequences observed in Temblor Formation outcrops has led to a better understanding of reservoir geology in West Coalinga Field. Based on the characteristics of stratigraphic bounding surfaces in the outcrops, these surfaces were identified in the subsurface using cores and logs. The bounding surfaces were mapped and then used as reference horizons in the reservoir modeling. Facies groups and facies tracts were recognized from outcrops and cores of the Temblor Formation and were applied to defining the stratigraphic framework and facies architecture for building 3D geological models. The following facies tracts were recognized: incised valley, estuarine, tide- to wave-dominated shoreline, diatomite, and subtidal. A new minipermeameter probe, which has important advantages over previous methods of measuring outcrop permeability, was developed during this project. The device, which measures permeability at the distal end of a small drillhole, avoids surface weathering effects and provides a superior seal compared with previous methods for measuring outcrop permeability. The new probe was used successfully for obtaining a high-quality permeability data set from an outcrop in southern Utah. Results obtained from analyzing the fractal structure of permeability data collected from the southern Utah outcrop and from core permeability data provided by Chevron from West Coalinga Field were used in distributing permeability values in 3D reservoir models. Spectral analyses and the Double Trace Moment method (Lavallee et al., 1991) were used to analyze the scaling and multifractality of permeability data from cores from West Coalinga Field. T2VOC, which is a numerical flow simulator capable of modeling multiphase, multi-component, nonisothermal flow, was used to model steam injection and oil production for a portion of section 36D in West Coalinga Field. The layer structure and permeability distributions of different models, including facies group, facies tract, and fractal permeability models, were incorporated into the numerical flow simulator. The injection and production histories of wells in the study area were modeled, including shutdowns and the occasional conversion of production wells to steam injection wells. The framework provided by facies groups provides a more realistic representation of the reservoir conditions than facies tracts, which is revealed by a comparison of the history-matching for the oil production. Permeability distributions obtained using the fractal results predict the high degree of heterogeneity within the reservoir sands of West Coalinga Field. The modeling results indicate that predictions of oil production are strongly influenced by the geologic framework and by the boundary conditions. The permeability data collected from the southern Utah outcrop, support a new concept for representing natural heterogeneity, which is called the fractal/facies concept. This hypothesis is one of the few potentially simplifying concepts to emerge from recent studies of geological heterogeneity. Further investigation of this concept should be done to more fully apply fractal analysis to reservoir modeling and simulation. Additional outcrop permeability data sets and further analysis of the data from distinct facies will be needed in order to fully develop

James W. Castle; Fred J. Molz; Ronald W. Falta; Cynthia L. Dinwiddie; Scott E. Brame; Robert A. Bridges

2002-10-30T23:59:59.000Z

304

Rangely, Colorado: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Rangely, Colorado: Energy Resources Rangely, Colorado: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 40.0874759°, -108.8048292° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.0874759,"lon":-108.8048292,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

305

Front Range Energy LLC | Open Energy Information  

Open Energy Info (EERE)

Energy LLC Energy LLC Jump to: navigation, search Logo: Front Range Energy LLC Name Front Range Energy LLC Address 31375 Great Western Dr Place Windsor, Colorado Zip 80550 Sector Biofuels Product Ethanol producer Website http://www.frontrangeenergy.co Coordinates 40.4605154°, -104.8565272° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.4605154,"lon":-104.8565272,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

306

Tonopah Test Range closure sites revegetation plan  

SciTech Connect

This document is a revegetation plan for long-term stabilization (revegetation) of land disturbed by activities associated with the closure of a Bomblet Pit and the Five Points Landfill. Both sites are on the Tonopah Test Range (TTR) located in south-central Nevada. This document contains general reclamation practices and procedures that will be followed during the revegetation of these sites. The revegetation procedures proposed have been developed over several years of research and include the results of reclamation trials at Area 11 and Area 19 on the Nevada Test Site (NTS), and more recently at the Double Tracks (Nellis Air Force Range) reclamation demonstration plots. In addition, the results of reclamation efforts and concurrent research efforts at the Yucca Mountain Project have been considered in the preparation of this revegetation plan.

Anderson, D.C.; Hall, D.B.

1997-05-01T23:59:59.000Z

307

Inertial range turbulence in kinetic plasmas  

E-Print Network (OSTI)

The transfer of turbulent energy through an inertial range from the driving scale to dissipative scales in a kinetic plasma followed by the conversion of this energy into heat is a fundamental plasma physics process. A theoretical foundation for the study of this process is constructed, but the details of the kinetic cascade are not well understood. Several important properties are identified: (a) the conservation of a generalized energy by the cascade; (b) the need for collisions to increase entropy and realize irreversible plasma heating; and (c) the key role played by the entropy cascade--a dual cascade of energy to small scales in both physical and velocity space--to convert ultimately the turbulent energy into heat. A strategy for nonlinear numerical simulations of kinetic turbulence is outlined. Initial numerical results are consistent with the operation of the entropy cascade. Inertial range turbulence arises in a broad range of space and astrophysical plasmas and may play an important role in the ther...

Howes, G G

2007-01-01T23:59:59.000Z

308

Inertial range turbulence in kinetic plasmas  

E-Print Network (OSTI)

The transfer of turbulent energy through an inertial range from the driving scale to dissipative scales in a kinetic plasma followed by the conversion of this energy into heat is a fundamental plasma physics process. A theoretical foundation for the study of this process is constructed, but the details of the kinetic cascade are not well understood. Several important properties are identified: (a) the conservation of a generalized energy by the cascade; (b) the need for collisions to increase entropy and realize irreversible plasma heating; and (c) the key role played by the entropy cascade--a dual cascade of energy to small scales in both physical and velocity space--to convert ultimately the turbulent energy into heat. A strategy for nonlinear numerical simulations of kinetic turbulence is outlined. Initial numerical results are consistent with the operation of the entropy cascade. Inertial range turbulence arises in a broad range of space and astrophysical plasmas and may play an important role in the thermalization of fusion energy in burning plasmas.

G. G. Howes

2007-11-27T23:59:59.000Z

309

High resolution sequence stratigraphic and reservoir characterization studies of D-07, D-08 and E-01 sands, Block 2 Meren field, offshore Niger Delta  

E-Print Network (OSTI)

Meren field, located offshore Niger Delta, is one of the most prolific oil-producing fields in the Niger Delta. The upper Miocene D-07, D-08 and E-01 oil sands comprise a series of stacked hydrocarbon reservoirs in Block 2 of Meren field. These reservoir sandstones were deposited in offshore to upper shoreface environments. Seven depositional facies were identified in the studied interval, each with distinct lithology, sedimentary structures, trace fossils, and wire-line log character. The dominant lithofacies are (1) locally calcite-cemented highly-bioturbated, fine-grained sandstones, (middle to lower shoreface facies); (2) cross-bedded, fine- to medium-grained well-sorted sandstones (upper shoreface facies); (3) horizontal to sub-horizontal laminated, very-fine- to fine-grained sandstone (delta front facies); (4) massive very-fine- to fine-grained poorly-sorted sandstone (delta front facies); (5) muddy silt- to fine-grained wavy-bedded sandstone (lower shoreface facies); (6) very-fine- to fine-grained sandy mudstone (lower shoreface facies); and (7) massive, silty shales (offshore marine facies). Lithofacies have distinct mean petrophysical properties, although there is overlap in the range of values. The highest quality reservoir deposits are cross-bedded sands that were deposited in high-energy upper shoreface environments. Calcite cements in lower shoreface facies significantly reduce porosity and permeability. Integration of core and wire-line log data allowed porosity and permeability to be empirically determined from bulk density. The derived equation indicated that bulk density values could predict 80% of the variance in core porosity and permeability values. Three parasequence sets were interpreted, including one lower progradational and two upper retrogradational parasequence sets. The progradational parasequence set consists of upward-coarsening delta front to upper shoreface facies, whereas the upward-fining retrogradational parasequence sets are composed of middle to lower shoreface deposits overlain by offshore marine shales. The limited amount of core data and the relatively small area of investigation place serious constraints on stratigraphic interpretations. Two possible sequence stratigraphic interpretations are presented. The first interpretation suggests the deposits comprise a highstand systems tract overlain by a transgressive systems tract. A lowstand systems tract is restricted to an incised valley fill at the southeastern end of the study area. The alternate interpretation suggests the deposits comprise a falling stage systems tract overlain by transgressive systems tract.

Esan, Adegbenga Oluwafemi

2002-12-01T23:59:59.000Z

310

Effect of temperature on oil/water relative permeabilities of unconsolidated and consolidated sands  

SciTech Connect

Over the last 20 years, a number of studies have reported temperature effects on two-phase relative permeabilities in porous media. However, some of the reported results have been contradictory. Also, observed effects have not been explained in terms of fundamental properties known to govern two-phase flow. The purpose of this study was to attempt to isolate the fundamental properties affecting two-phase relative permeabilities at elevated temperature. Laboratory dynamic displacement relative permeability measurements were made on unconsolidated and consolidated sand cores, using water and a refined white mineral oil. Experiments were run on 2 in. (51 mm) diameter, 20 in. (510 mm) long cores from room temperature to 300/sup 0/F (149/sup 0/C). Unlike the results of previous researchers, essentially no changes with temperatures were observed in either residual saturations or relative permeability relationships. It was concluded that previous results may have been affected by viscous instabilities, capillary end-effects, and/or difficulties in maintaining material balances.

Miller, M.A.; Ramey, H.J.

1983-10-01T23:59:59.000Z

311

Impact of early diagenesis of Eolian reservoirs, Great Sand Dunes National Monument, Colorado  

SciTech Connect

Dune and associated alluvial and playa deposits at Great Sand Dunes National Monument, Colorado, provide an excellent opportunity to study early diagenetic development of vertical and horizontal permeability barriers in recent eolian deposits (> 10 ka). Cements observed include calcite, aragonite, protodolomite(.), amorphous silica, iron hydroxide, smectite, trona, and halite. Cementation is controlled by the availability of water, with several hydrologic subenvironments producing different cements. Evaporative cementation in dunes adjacent to playas is commonly dominated by trona and halite, but calcite, aragonite, and amorphous silica also bind the sediment. These cements are generally most concentrated in fine laminations where capillary action has pulled water into dunes. Iron hydroxides, calcite, and amorphous silica precipitate at the interface between ground water and streams or lakes, where the pH gradient may exceed 5 pH units (pH 5.7-11.5). Subsequent movement of the ground-water table can result in cross-cutting cement zones. Early cementation in dunes prevents deflation and provides a mechanism for preservation of the reservoir unit. Intense cementation may permanently occlude porosity, or leaching may reestablish well-interconnected porosity. An understanding of the extent and composition of early cement zones can be used to improve hydrodynamic models for production and enhanced recovery.

Krystinik, L.F.; Andrews, S.; Fryberger, S.G.

1985-02-01T23:59:59.000Z

312

Guide to preparing SAND reports and other communication products : version 4.  

SciTech Connect

This guide describes the R&A process, Common Look and Feel requirements, and preparation and publishing procedures for communication products at Sandia National Laboratories. Samples of forms and examples of published communications products are provided. This guide takes advantage of the wealth of material now available on the Web as a resource. Therefore, it is best viewed as an electronic document. If some of the illustrations are too small to view comfortably, you can enlarge them on the screen as needed. The most significant changes since Version 1 involve the introduction of the electronic Review and Approval application at the Sandia/California (CA) and Sandia/New Mexico (NM) sites. Authors are advised to check the most current material on the application Web site before initiating the R&A process. The format of this document is considerably different than that expected of a SAND Report. It was selected to permit the large number of illustrations and examples to be placed closer to the text that references them. In the case of forms, covers, and other items that are included as examples, a link to the Web is provided so that you can access the items and download them for use.

Brittenham, Phillip W.

2007-09-01T23:59:59.000Z

313

Guide to preparing SAND reports and other communication products : version 3.  

SciTech Connect

This guide describes the R&A process, Common Look and Feel requirements, and preparation and publishing procedures for communication products at Sandia National Laboratories. Samples of forms and examples of published communications products are provided. This guide takes advantage of the wealth of material now available on the Web as a resource. Therefore, it is best viewed as an electronic document. If some of the illustrations are too small to view comfortably, you can enlarge them on the screen as needed. The most significant changes since Version 1 involve the introduction of the electronic Review and Approval application at the Sandia/California (CA) and Sandia/New Mexico (NM) sites. Authors are advised to check the most current material on the application Web site before initiating the R&A process. The format of this document is considerably different than that expected of a SAND Report. It was selected to permit the large number of illustrations and examples to be placed closer to the text that references them. In the case of forms, covers, and other items that are included as examples, a link to the Web is provided so that you can access the items and download them for use.

Brittenham, Phillip W.

2007-03-01T23:59:59.000Z

314

Evaluation of Brine-Bearing Sands of the Frio Formation, Upper Texas Gulf Coast for Geological Sequestration of CO2  

NLE Websites -- All DOE Office Websites (Extended Search)

Evaluation of Brine-Bearing Sands of the Evaluation of Brine-Bearing Sands of the Frio Formation, Upper Texas Gulf Coast for Geological Sequestration of CO 2 S. D. Hovorka (susan.hovorka@beg.utexas.edu; 512-471-4863) Bureau of Economic Geology, P.O. Box X, The University of Texas at Austin, Austin, TX 78713 C. Doughty (CADoughty@lbl.gov; 510-486-6453 ) Lawrence Berkeley National Lab, 1 Cyclotron Road Mailstop 90-1116, Berkeley, CA 94720 P. R. Knox (paul.knox@beg.utexas.edu; 512-471-7313), Bureau of Economic Geology, P.O. Box X, The University of Texas at Austin, Austin, TX 78713 C. T. Green (ctgreen@ucdavis.edu; 510-495-2461) University of California, Hydrologic Sciences, One Shields Ave., Davis, CA 95616 K. Pruess(K_Pruess@lbl.gov; 510-486-6732) Lawrence Berkeley National Lab, 1 Cyclotron Road Mailstop 90-1116,

315

Capacity Investigation of Brine-Bearing Sands of the Frio Formation for Geologic Sequestration of CO2  

NLE Websites -- All DOE Office Websites (Extended Search)

Capacity Investigation of Brine-Bearing Sands of the Frio Capacity Investigation of Brine-Bearing Sands of the Frio Formation for Geologic Sequestration of CO 2 Christine Doughty (cadoughty@lbl.gov; 510-486-6453) Karsten Pruess (k_pruess@lbl.gov; 510-486-6732) Sally M. Benson (smbenson@lbl.gov; 510-486-5875) Lawrence Berkeley National Laboratory 1 Cyclotron Rd, MS 90-1116 Berkeley, CA 94720 Susan D. Hovorka (susan.hovorka@beg.utexas.edu; 512-471-4863) Paul R. Knox (paul.knox@beg.utexas.edu; 512-471-7313) Bureau of Economic Geology P.O. Box X, The University of Texas Austin, TX 78713 Christopher T. Green (ctgreen@ucdavis.edu; 530-752-1372) University of California, Hydrologic Sciences 1 Shields Ave. Davis, CA 95616 Abstract The capacity of fluvial brine-bearing formations to sequester CO 2 is investigated using numerical simulations of CO

316

Size exclusion chromatography-inductively coupled plasma atomic emission spectrographic study of Fe in bitumens derived from tar sands  

SciTech Connect

This paper reports on bitumens extracted from tar sands from various locations (Utah, California, Kentucky, and Alberta) that were examined by size exclusion chromatography with on-line element-specific detection to study the Fe concentration as a function of size. In most cases, the resulting profiles exhibit unimodal distributions at relatively large molecular size with very similar times for maximum elution. specifically, Sunnyside (Utah) and McKittrick (California) tar-sand bitumens exhibited very intense maxima consistent with extremely high bulk Fe contents. Arroyo Grande (California) exhibited an additional maximum at very large molecular size. This size behavior of the Fe appears to correlate with the large molecular size Ni and V components eluted under the same conditions.

Reynolds, J.G. (Lawrence Livermore National Lab., Livermore, CA (US)); Biggs, W.R. (Chevron Research Co., Richmond, CA (US))

1992-01-01T23:59:59.000Z

317

Sand-rich submarine fans, Mio-Pliocene of Santa Monica Basin, offshore California: Untapped exploration targets  

Science Conference Proceedings (OSTI)

Santa Monica Basin lies directly west of Los Angeles Basin, one of the world's most prolific oil provinces. Published literature suggests that Santa Monica Basin was starved of coarse clastics during the late Miocene through Pliocene. However, seismic sequence stratigraphy indicates that deposition of sand-rich fans alternated with mixed-load systems throughout the Delmontian and Repettian stages. Seismic sequences and facies are calibrated to seismic and well data from Beta Oil Field, in San Pedro Basin to the south. Eustasy evidently played a dominant role in controlling sedimentation. Variations in tan lithology, thickness, and basinward extent correspond to worldwide changes in sea level. Regional erosion surfaces apparently signify drops in sea level. Overlying thick seismic packages display hummocky to chaotic seismic facies separated by high- to low-amplitude continuous reflections. These configurations are interpreted as inner- to mid-fan channels separated by overbank deposits in sand-rich lowstand fans. High-amplitude basinwide reflections bound the tops of the sand-rich intervals, and likely represent condensed sections formed during sea-level rises. Thin seismic intervals above the condensed sections display downlap, and are interpreted as interbedded sandstones and shales of prograding highstand fans. Sediment input to Santa Monica Basin, based on seismic-facies and isochron patterns, was predominantly from the (present-day) north, with subordinate input from the east. High-amplitude eustatic variations dominated deposition and sequence development even in this tectonically active basin Previously unidentified sand-rich fans are present, and have not been drilled.

May, J.A.; McMillen, K.J.

1996-01-01T23:59:59.000Z

318

Studies of the terrestrial O{sub 2} and carbon cycles in sand dune gases and in biosphere 2  

Science Conference Proceedings (OSTI)

Molecular oxygen in the atmosphere is coupled tightly to the terrestrial carbon cycle by the processes of photosynthesis, respiration, and burning. This dissertation examines different aspects of this coupling in four chapters. Chapter 1 explores the feasibility of using air from sand dunes to reconstruct atmospheric O{sub 2} composition centuries ago. Such a record would reveal changes in the mass of the terrestrial biosphere, after correction for known fossil fuel combustion, and constrain the fate of anthropogenic CO{sub 2}.

Severinghaus, J.P.

1995-12-31T23:59:59.000Z

319

Report on variation of electrical conductivity during steam injection in unconsolidated sand saturated with a salt solution  

SciTech Connect

Geophysical electrical methods are useful in evaluating the performance of certain classes of enhanced oil recovery (EOR) operations and also remediation operations for contaminant spills. Electrical resistivity is sensitive to the concentration of ionic species in solution in fluids present in the subsurface zone. Such fluids are displaced during oil recovery operations and contaminant remediation. If the resistivity of the displacing fluid differs from the in situ fluid, then a geophysical method for detecting resistivity variations may be capable of tracking the advance of the displacing fluid. This report presents the results of experiments designed to determine the variations in resistivity that occur when steam is injected into a homogeneous, fully-saturated sand. These experiments were simple, one-dimensional laboratory steam injection experiments. They were performed using a glass tube filled with a tightly-packed sand and fitted with an injection port at one end and an exit port at the other In each experiment, the sand pack was initially saturated with a brine and then steam was introduced at one end of the tube. Analytic solutions for the steam front velocity, steam temperature, steam distribution, salt concentration profile, and liquid saturation are presented and are used with appropriate correlations of electrical conductivity to describe the observed behavior. The results of these experiments should provide experimental justification for the electrical conductivity variations that are calculated from the analytic solutions. In addition, the experiments may yield new information regarding features of the data that may not result from the analytical modelling.

Vaughan, P. [California Univ., Berkeley, CA (United States). Dept. of Materials Science and Mineral Engineering; Udell, K.S. [California Univ., Berkeley, CA (United States). Dept. of Mechanical Engineering; Wilt, M. [Lawrence Livermore National Lab., CA (United States)

1992-04-01T23:59:59.000Z

320

Feasibility of calculating petrophysical properties in tight-sand reservoirs using neural networks. Final report, October 1989-July 1991  

Science Conference Proceedings (OSTI)

The objective of the research was to determine the feasibility of using neural networks to estimate petrophysical properties in tight sand reservoirs. A second objective was to gain some experience concerning how to approach the development of a future prototype, including what should be done and what should be avoided. Gas Research Institute (GRI) focused the project on tight sands because they contain enormous gas reserves and their complicated lithology represents a challenge to log analysts. The data were supplied by GRI from two of its geographically proximate experimental wells in tight sand formations. The nets were tested in sections of those wells that were not used for training, and in two other wells, one in a geographically close but geologically unrelated formation and one in Wyoming. The feasibility testing demonstrated that the relatively simple neural networks developed have comparable accuracy with standard logging analysis estimates in wells that contributed data to the training set. Transportability of the network was tested by using core measurements in two wells in which the nets were not trained, with inconclusive results. Recommendations were made to increase the accuracy of the neural networks.

Urquidi-Macdonald, M.; Javitz, H.S.; Park, W.; Lee, J.D.; Bergman, A.

1991-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Continuity and permeability development in the tight gas sands of the eastern Uinta Basin, Utah. Final report  

SciTech Connect

The relationships between reservoir characteristics and flow regimes exhibited by twenty-one Uinta Basin gas wells represent fluvial, lake margin, and lacustrine deposits. Production data were analyzed to determine the type of flow for each well. This analysis indicated that one well exhibits radial flow, thirteen wells linear flow, and seven wells indeterminate flow regimes. Values of SSP, ..delta..t, R/sub w/ and SP curve patterns were determined from well logs. These data were compared for the three types of flow observed. It appears that SSP, R/sub w/ and SP pattern may be useful in qualitatively distinguishing between sands of low continuity and those with moderate continuity. The permeabilities are considerably higher than those normally attributed to ''tight sands.'' Also permeability correlates inversely with the number of sands completed in each well. Consideration of the orientations of linear features in the area and those of reservoir lenses in outcrops indicates that the relationship between frac orientation and lens geometry cannot be effectively predicted without a good technique to predict lens orientation. Completion strategies to optimize frac efficiency are suggested, based upon the findings of this study.

Knutson, C.F.; Boardman, C.R.

1978-05-01T23:59:59.000Z

322

Characterization of Black Trona Waters and use of the waters for recovery of bitumen from US tar sands  

Science Conference Proceedings (OSTI)

There were two principal research objectives for this project. The first objective was to characterize organic material in Black Trona Water with an emphasis on colloids and organic acids. The second objective was to determine the utility of Black Trona Water as a solvent for extracting fossil fuels from US Tar Sands. Spectroscopic studies, molecular weights and shapes of polymeric acids and behavior as a polysoap were determined. Experiments indicate that trona water is preferable to Black Trona Water as an extraction agent for tar sands. The trona water is fairly efficient at stripping bitumen from the sand with gentle heating. In trona water, the displaced bitumen is readily collected on a Teflon surface (i.e., a non-water-wetted surface) with little material dissolving in the water. In contrast, the polysoap in Black Trona Water appears to take up displaced bitumen in a detergent-like process. Separating bitumen from the polysoap would undoubtedly be very difficult. 38 references, 16 figures, 2 tables.

Barden, R.E.

1984-09-01T23:59:59.000Z

323

Permeability of laboratory-formed methane-hydrate-bearing sand: Measurements and observations using x-ray computed tomography  

SciTech Connect

Methane hydrate was formed in two moist sands and a sand/silt mixture under a confining stress in an X-ray-transparent pressure vessel. Three initial water saturations were used to form three different methane-hydrate saturations in each medium. X-ray computed tomography (CT) was used to observe location-specific density changes caused by hydrate formation and flowing water. Gas-permeability measurements in each test for the dry, moist, frozen, and hydrate-bearing states are presented. As expected, the effective permeabilities (intrinsic permeability of the medium multiplied by the relative permeability) of the moist sands decreased with increasing moisture content. In a series of tests on a single sample, the effective permeability typically decreased as the pore space became more filled, in the order of dry, moist, frozen, and hydrate-bearing. In each test, water was flowed through the hydrate-bearing medium and we observed the location-specific changes in water saturation using CT scanning. We compared our data to a number of models, and our relative permeability data compare most favorably with models in which hydrate occupies the pore bodies rather than the pore throats. Inverse modeling (using the data collected from the tests) will be performed to extend the relative permeability measurements.

Kneafsey, T. J.; Seol, Y.; Gupta, A.; Tomutsa, L.

2010-09-15T23:59:59.000Z

324

APS Long Range Operations Schedule FY2009  

NLE Websites -- All DOE Office Websites (Extended Search)

09) 09) Alternate Formats: iCal | Excel | PDF APS Long Range Operation Schedule (FY2009) 2008-3 2009-1 2009-2 Sep Oct Nov Dec Jan Feb Mar Apr May Jun Jul Aug Sep 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5

325

APS Long Range Operations Schedule FY2010  

NLE Websites -- All DOE Office Websites (Extended Search)

10) 10) Alternate Formats: iCal | Excel | PDF APS Long-Range Operation Schedule 2009-3 2010-1 2010-2 Sep Oct Nov Dec Jan Feb Mar Apr May Jun Jul Aug Sep 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5

326

Fan-less long range alpha detector  

DOE Patents (OSTI)

A fan-less long range alpha detector which operates by using an electrical field between a signal plane and the surface or substance to be monitored for air ions created by collisions with alpha radiation. Without a fan, the detector can operate without the possibility of spreading dust and potential contamination into the atmosphere. A guard plane between the signal plane and the electrically conductive enclosure and maintained at the same voltage as the signal plane, reduces leakage currents. The detector can easily monitor soil, or other solid or liquid surfaces.

MacArthur, Duncan W. (Los Alamos, NM); Bounds, John A. (Los Alamos, NM)

1994-01-01T23:59:59.000Z

327

Fan-less long range alpha detector  

DOE Patents (OSTI)

A fan-less long range alpha detector is disclosed which operates by using an electrical field between a signal plane and the surface or substance to be monitored for air ions created by collisions with alpha radiation. Without a fan, the detector can operate without the possibility of spreading dust and potential contamination into the atmosphere. A guard plane between the signal plane and the electrically conductive enclosure and maintained at the same voltage as the signal plane, reduces leakage currents. The detector can easily monitor soil, or other solid or liquid surfaces. 2 figures.

MacArthur, D.W.; Bounds, J.A.

1994-05-10T23:59:59.000Z

328

Relevant energy ranges for astrophysical reaction rates  

Science Conference Proceedings (OSTI)

Effective energy windows (Gamow windows) of astrophysical reaction rates for (p,gamma), (p,n), (p,alpha), (alpha,gamma), (alpha,n), (alpha,p), (n,gamma), (n,p), and (n,alpha) on targets with 10<=Z<=83 from proton to neutron dripline are calculated using theoretical cross sections. It is shown that widely used approximation formulas for the relevant energy ranges are not valid for a large number of reactions relevant to hydrostatic and explosive nucleosynthesis. The influence of the energy dependence of the averaged widths on the location of the Gamow windows is discussed and the results are presented in tabular form.

Rauscher, Thomas [Department of Physics, University of Basel, Klingelbergstr. 82, CH-4056 Basel (Switzerland)

2010-04-15T23:59:59.000Z

329

Tonopah Test Range 2030 Meeting Summary Report  

SciTech Connect

Corrective Action Sites (CASs) and Corrective Action Units (CAUs) at the Tonopah Test Range (TTR) may be placed into three categories: Closed, Closed in Place, or Closure in Progress. CASs and CAUs where contaminants were either not detected or were cleaned up to within regulatory action levels are summarized. CASs and CAUs where contaminants and/or waste have been closed in place are summarized. There is also a table that summarizes the contaminant that has been closed at each site, if land-use restrictions are present, and if post-closure inspections are required.

NSTec Environmental Restoration

2009-04-01T23:59:59.000Z

330

Impacts of human trampling and periodic sand inundation on Southern California intertidal algal turf communities : implications for conservation and management of rocky shores  

E-Print Network (OSTI)

associated with rocky shore algae. Pgs. 36- 56 in: P.G.associated with rocky shore algae. In: P. G. Moore & R.h. Boulder Boulder / Turf Other Algae Sand > 50 mm, < 200 mm

Huff, Tonya Michelle

2006-01-01T23:59:59.000Z

331

EXCEPTED SERVICE (EJ & EK) PAY RANGES  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EXCEPTED SERVICE (EJ & EK) PAY RANGES EXCEPTED SERVICE (EJ & EK) PAY RANGES Eff. 01/03/2010 Pay Table (***Excludes applicable Locality Pay) Grade/Band Minimum Maximum GS Grade/Step Equivalent 01 $27,431 $47,103 5/1 to 9/5 02 $41,563 $68,310 9/1 to 12/5 03 $60,274 $95,989 12/1 to 14/5 04 $84,697 $133,403* 14/1 to 103% of 15/10 05 $145,700** $165,300 EX-V to EX-III *Change to maximum pay rate per DOE O 329.1 effective 03/30/2012. **Change to minimum pay rate per DOE O 329.1 effective 03/30/2012. ***Calculating salary to include Locality Pay: Example: An employee is selected for an EJ/EK position in the Washington, D.C. Metropolitan Area which has a locality payment rate of 24.22% (locality rate for 2011) Step One: Convert locality payment percent to a decimal - 1.2422;

332

APS Long Range Schedule FY1996  

NLE Websites -- All DOE Office Websites (Extended Search)

Long Range Commissioning Schedule for FY1996 Long Range Commissioning Schedule for FY1996 Date First Shift 0:00-8:00 Second Shift 8:00-16:00 Third Shift 16:00-24:00 3/15/96 SR Studies 1-ID-A Shielding Verification SR Studies 3/23/96 SR Studies 3-ID-A , 2-ID-A , 3-ID-B Shielding Verifications User Beam 3/24/96 User Beam User Beam User Beam 3/25/96 User Beam 19-ID-A Shielding Verification User Beam 3/26/96 User Beam 2-ID-A , 12-BM-A Shielding Verifications User Beam 3/27/96 User Beam 5-BM-A Shielding Verification User Beam 3/28/96 User Beam 19-ID-C Shielding Verification User Beam until 20:00 3/29/96 SR Studies SR Studies SR Studies 3/30/96 SR Studies SR Studies SR Studies 3/31/96 SR Studies SR Studies SR Studies 4/1/96 SR Studies SR Studies SR Studies 4/2/96 SR Studies 5-BM-B Shielding Verification User Beam

333

Volatile compound evolution from the programmed temperature pyrolysis of Big Clifty and McKittrick tar sands at a 10 degrees C/min heating rate  

DOE Green Energy (OSTI)

Big Clifty (Kentucky) and McKittrick (California) tar sands were pyrolyzed at a 10{degrees}C/min heating rate from room temperature to 900{degrees}C. The volatile compounds were detected on-line and in real time by tandem mass spectrometry using MS and MS/MS detection. This paper reports the programmed temperature pyrolysis behaviors of Big Clifty and McKittrick tar sands and compares their results. 48 refs., 10 figs., 3 tabs.

Reynolds, J.G.

1989-11-01T23:59:59.000Z

334

Design and Implementation of Energized Fracture Treatment in Tight Gas Sands  

SciTech Connect

Hydraulic fracturing is essential for producing gas and oil at an economic rate from low permeability sands. Most fracturing treatments use water and polymers with a gelling agent as a fracturing fluid. The water is held in the small pore spaces by capillary pressure and is not recovered when drawdown pressures are low. The un-recovered water leaves a water saturated zone around the fracture face that stops the flow of gas into the fracture. This is a particularly acute problem in low permeability formations where capillary pressures are high. Depletion (lower reservoir pressures) causes a limitation on the drawdown pressure that can be applied. A hydraulic fracturing process can be energized by the addition of a compressible, sometimes soluble, gas phase into the treatment fluid. When the well is produced, the energized fluid expands and gas comes out of solution. Energizing the fluid creates high gas saturation in the invaded zone, thereby facilitating gas flowback. A new compositional hydraulic fracturing model has been created (EFRAC). This is the first model to include changes in composition, temperature, and phase behavior of the fluid inside the fracture. An equation of state is used to evaluate the phase behavior of the fluid. These compositional effects are coupled with the fluid rheology, proppant transport, and mechanics of fracture growth to create a general model for fracture creation when energized fluids are used. In addition to the fracture propagation model, we have also introduced another new model for hydraulically fractured well productivity. This is the first and only model that takes into account both finite fracture conductivity and damage in the invaded zone in a simple analytical way. EFRAC was successfully used to simulate several fracture treatments in a gas field in South Texas. Based on production estimates, energized fluids may be required when drawdown pressures are smaller than the capillary forces in the formation. For this field, the minimum CO{sub 2} gas quality (volume % of gas) recommended is 30% for moderate differences between fracture and reservoir pressures (2900 psi reservoir, 5300 psi fracture). The minimum quality is reduced to 20% when the difference between pressures is larger, resulting in additional gas expansion in the invaded zone. Inlet fluid temperature, flow rate, and base viscosity did not have a large impact on fracture production. Finally, every stage of the fracturing treatment should be energized with a gas component to ensure high gas saturation in the invaded zone. A second, more general, sensitivity study was conducted. Simulations show that CO{sub 2} outperforms N{sub 2} as a fluid component because it has higher solubility in water at fracturing temperatures and pressures. In fact, all gas components with higher solubility in water will increase the fluid's ability to reduce damage in the invaded zone. Adding methanol to the fracturing solution can increase the solubility of CO{sub 2}. N{sub 2} should only be used if the gas leaks-off either during the creation of the fracture or during closure, resulting in gas going into the invaded zone. Experimental data is needed to determine if the gas phase leaks-off during the creation of the fracture. Simulations show that the bubbles in a fluid traveling across the face of a porous medium are not likely to attach to the surface of the rock, the filter cake, or penetrate far into the porous medium. In summary, this research has created the first compositional fracturing simulator, a useful tool to aid in energized fracture design. We have made several important and original conclusions about the best practices when using energized fluids in tight gas sands. The models and tools presented here may be used in the future to predict behavior of any multi-phase or multi-component fracturing fluid system.

Mukul Sharma; Kyle Friehauf

2009-12-31T23:59:59.000Z

335

Range Selectivity Estimation for Continuous Attributes  

E-Print Network (OSTI)

Many commercial database systems maintain histograms to efficiently estimate query selectivities as part of query optimization. Most work on histogram design is implicitly geared towards discrete or categorical attribute value domains. In this paper, we consider approaches that are better suited for the continuous valued attributes commonly found in scientific and statistical databases. We propose two methods based on spline functions for estimating the selectivity of range queries over univariate and multivariate data. These methods are more accurate than histograms. As the results from our experiments on both real and synthetic data sets demonstrate, the proposed methods achieved substantially better (up to 5.5 times) estimation error than the state-of-the-art histograms, at exactly the same storage space and with comparable CPU runtime overhead; moreover, the superiority of the proposed spline methods is amplified when applied to multivariate data. 1 Introduction Selectivity esti...

Flip Korn; Theodore Johnson; H. V. Jagadish

1999-01-01T23:59:59.000Z

336

Scannerless loss modulated flash color range imaging  

SciTech Connect

Scannerless loss modulated flash color range imaging methods and apparatus are disclosed for producing three dimensional (3D) images of a target within a scene. Apparatus and methods according to the present invention comprise a light source providing at least three wavelengths (passbands) of illumination that are each loss modulated, phase delayed and simultaneously directed to illuminate the target. Phase delayed light backscattered from the target is spectrally filtered, demodulated and imaged by a planar detector array. Images of the intensity distributions for the selected wavelengths are obtained under modulated and unmodulated (dc) illumination of the target, and the information contained in the images combined to produce a 3D image of the target.

Sandusky, John V. (Albuquerque, NM); Pitts, Todd Alan (Rio Rancho, NM)

2009-02-24T23:59:59.000Z

337

Scannerless loss modulated flash color range imaging  

SciTech Connect

Scannerless loss modulated flash color range imaging methods and apparatus are disclosed for producing three dimensional (3D) images of a target within a scene. Apparatus and methods according to the present invention comprise a light source providing at least three wavelengths (passbands) of illumination that are each loss modulated, phase delayed and simultaneously directed to illuminate the target. Phase delayed light backscattered from the target is spectrally filtered, demodulated and imaged by a planar detector array. Images of the intensity distributions for the selected wavelengths are obtained under modulated and unmodulated (dc) illumination of the target, and the information contained in the images combined to produce a 3D image of the target.

Sandusky, John V. (Albuquerque, NM); Pitts, Todd Alan (Rio Rancho, NM)

2008-09-02T23:59:59.000Z

338

Ultrasonic ranging and data telemetry system  

DOE Patents (OSTI)

An ultrasonic ranging and data telemetry system determines a surveyor's position and automatically links it with other simultaneously taken survey data. An ultrasonic and radio frequency (rf) transmitter are carried by the surveyor in a backpack. The surveyor's position is determined by calculations that use the measured transmission times of an airborne ultrasonic pulse transmitted from the backpack to two or more prepositioned ultrasonic transceivers. Once a second, rf communications are used both to synchronize the ultrasonic pulse transmission-time measurements and to transmit other simultaneously taken survey data. The rf communications are interpreted by a portable receiver and microcomputer which are brought to the property site. A video display attached to the computer provides real-time visual monitoring of the survey progress and site coverage.

Brashear, Hugh R. (Farragut, TN); Blair, Michael S. (Knoxville, TN); Phelps, James E. (Knoxville, TN); Bauer, Martin L. (Oak Ridge, TN); Nowlin, Charles H. (Oak Ridge, TN)

1990-01-01T23:59:59.000Z

339

Measurements of Detailed Temperature Profiles within the Radar Range Gate Using the Range Imaging Technique  

Science Conference Proceedings (OSTI)

The present study applies the range imaging (RIM) technique to radio acoustic sounding system (RASS) measurements in an attempt to improve the vertical resolution of temperature profiles obtained by RASS measurements.

Jun-ichi Furumoto; Tomonori Shinoda; Atsushi Matsugatani; Toshitaka Tsuda

2011-01-01T23:59:59.000Z

340

A Short-Range to Early-Medium-Range Ensemble Prediction System for the European Area  

Science Conference Proceedings (OSTI)

An ensemble prediction system, especially designed for the short to early-medium range for the European domain, is presented. The initial perturbations of each ensemble are based on singular vectors that maximize the 3-day total energy error ...

H. Hersbach; R. Mureau; J. D. Opsteegh; J. Barkmeijer

2000-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Tonopah Test Range Post-Closure Inspection Annual Report, Tonopah Test Range, Nevada, Calendar Year 2003  

Science Conference Proceedings (OSTI)

This post-closure inspection report provides documentation of the semiannual inspection activities, maintenance and repair activities, and conclusions and recommendations for calendar year 2003 for eight corrective action units located on the Tonopah Test Range, Nevada.

U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office; Bechtel Nevada

2004-04-01T23:59:59.000Z

342

Radorrletry P. G. Weber Los Alamos National Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

scattering and absorption) for characterizing atmospheric solid and liquid aerosols (particles and clouds). The baseline boundary conditions for the study included the...

343

GEOSYNTHETIC DAM LINING SYSTEMS By: Christine T. Weber1  

E-Print Network (OSTI)

). Finally, the fish ladder at Little Goose Dam uses pumped river water rather than a gravity flow. Of all GOOSE DAM ON UPSTREAM MOVEMENTS OF ADULT CHINOOK SALMON, ONCORHYNCHUS TSHAWYTSCHA A major environmental effects of hydroelectric dams (Figure 1) on the upstream movements of adult salmonids. Results indicated

Zornberg, Jorge G.

344

Aerial radiation survey at a military range.  

SciTech Connect

Aberdeen Proving Ground (APG) is currently listed on the Superfund National Priorities List because of past waste handling practices at 13 'study areas.' Concern has been expressed that anthropogenic radioisotopes may have been released at some of the study areas, with the potential of posing health risks to human or ecological receptors. This concern was addressed by thoroughly searching archival records, sampling and analyzing environmental media, and performing an aerial radiation survey. The aerial radiation survey techniques employed have been used over all U.S. Department of Energy and commercial reactor sites. Use of the Aerial Measurement System (AMS) allowed investigators to safely survey areas where surveys using hand-held instruments would be difficult to perform. In addition, the AMS delivered a full spectrum of the measured gamma radiation, thereby providing a means of determining which radioisotopes were present at the surface. As a quality check on the aerial measurements, four ground truth measurements were made at selected locations and compared with the aerial data for the same locations. The results of the survey revealed no evidence of surface radioactive contamination. The measured background radiation, including the cosmic contribution, ranged from 4 to 11 {mu}R/h.

Williams, G. P.; Martino, L. E.; Wrobel, J.; Environmental Assessment; U.S. Army Aberdeen Proving Ground

2001-04-01T23:59:59.000Z

345

Laboratory study on the use of tire shreds and rubber-sand in backfills and reinforced soil applications. Final report  

Science Conference Proceedings (OSTI)

Millions of scrap tires are discarded annually in the United States, the bulk of which are currently landfilled or stockpiled. This consumes valuable landfill space, or, if improperly disposed, creates a fire hazard and provides a prolific breeding ground for rates and mosquitoes. The use of tire shreds as lightweight fill material can sharply reduce the tire disposal problem. The present study, based on laboratory testing and numerical modeling, examines the feasibility of incorporating tire shreds and rubber-sand mixtures as lightweight geomaterial in embankments and backfills.

Bernal, A.; Lovell, C.W.; Salgado, R.

1996-12-20T23:59:59.000Z

346

Numerical modeling of gas migration into and through faulted sand reservoirs in Pabst Field (Main Pass East Block 259), northern Gulf of Mexico  

E-Print Network (OSTI)

The further exploration and development of Pabst Gas Field with faulted sand reservoirs require an understanding of the properties and roles of faults, particularly Low Throw near Vertical Faults (LTNVFs), in gas migration and accumulation at a reservoir scale. This study presents numerical modeling of gas migration and accumulation processes in Pabst Field. Based on studies of the reservoirs, structure, faults, and fluid properties of the field, reservoir scale modeling was performed to determine the gas supply style and the fault properties by means of hundreds of iterations in which the fault properties and gas supply pattern were modified to match the gas distribution obtained from modeling with the gas distribution inferred from seismic data constrained by well data and production data. This study finds that in the main three sand reservoirs of Pabst Field the overlying younger sands cut down into the underlying older sands, so that partial connections between the three sands allow gas communication among the sands. Meanwhile, three fault families break up the three sands into numerous compartments. A primary fault and large synthetic and antithetic faults act as gas migration pathways: the synthetic and antithetic faults are inlets for gas flow and the primary fault is an outlet, and LTNVFs act as barriers to gas flow. Modeling requires fault properties in the field to change while the field is formed. The porosity and permeability of the faults in Pabst Field are 10% and 0.1 md, respectively, during gas charging of the sand reservoirs. But when there is no gas charging and large gas columns are maintained, the porosity and permeability of the faults decrease to 6% and 0.001 md, respectively. Pabst Field probably has an impulse gas charge history. Fault opening and closing, gas charge and recharge, and replacement of gas by formation water may occur. A combination of stratigraphy, structure, overpressure and gas charge rate control gas migration style, gas charge history, and gas distribution in the field. The significance of the study is that this improved numerical approach for modeling gas migration into and through specifically faulted sand reservoirs fills the gap between basin modeling and production modeling.

Li, Yuqian

2005-05-01T23:59:59.000Z

347

Geographic Information System At Northern Basin & Range Region...  

Open Energy Info (EERE)

Geographic Information System At Northern Basin & Range Region (Laney, 2005) Exploration Activity Details Location Northern Basin and Range Geothermal Region Exploration Technique...

348

Analysis of Long-range Clean Energy Investment Scenarios for...  

NLE Websites -- All DOE Office Websites (Extended Search)

of Long-range Clean Energy Investment Scenarios for Eritrea, East Africa Title Analysis of Long-range Clean Energy Investment Scenarios for Eritrea, East Africa Publication Type...

349

Supplying Synthetic Crude Oil from Canadian Oil Sands: A Comparative Study of the Costs and CO2 Emissions of Mining and In-Situ Recovery  

E-Print Network (OSTI)

, and of unconventional deposits such as heavy oils, tar sands and oil shales.” As conventional oil becomes scarcer, the transport sector will remain dependent on petroleum resources, if no oil substitute is available. Fuels from non-conventional oil resources... www.eprg.group.cam.ac.uk E P R G W O R K IN G P A P E R Abstract Supplying Synthetic Crude Oil from Canadian Oil Sands: A Comparative Study of the Costs and CO2 Emissions of Mining and In-situ Recovery EPRG Working Paper 1005...

Méjean, A; Hope, Chris

350

Jayasumana ”Performance tradeoffs of shared limited range wavelength conversion schemes  

E-Print Network (OSTI)

Abstract — Performance of all-optical switches that employee different types of limited-range wavelength converters (LRWC) are investigated. Previous work has shown that there is a remarkable improvement in blocking probability while using LRWC over full range conversion, but has not considered the coincident effect of conversion resources sharing. We consider the case where an incoming wavelength can be converted to a range of outgoing wavelengths, where d is the range of conversion. The simulation results demonstrate that the performance improvement obtained by full range wavelength conversion can almost be achieved by using a fractional ranged ranged LRWC. I.

Fahad A. Al-zahrani; Abdulgader A. Habiballa; Ayman G. Fayoumi; Anura P. Jayasumana

2005-01-01T23:59:59.000Z

351

Measuring Range Anxiety: the Substitution-Emergency-Detour (SED) Method  

Science Conference Proceedings (OSTI)

Range anxiety has been widely recognized as a critical barrier for battery electric vehicles (BEV), but its measurement method is lacking. Such a knowledge gap makes it difficult to analyse the competiveness of and the demand for BEVs. This study develops the Substitution-Emergency-Detour (SED) method to measure the range anxiety cost, and conducts sensitivity analysis of range anxiety cost with respect to nine factors. It is found that the most effective ways to reduce range anxiety are reducing driving intensity, increasing the vehicle range, extending the vehicle range with better charging infrastructure. Better household vehicle flexibility and less range uncertainty can also significantly reduce range anxiety. The SED method and the numerical results are expected to contribute to better understanding of the range anxiety barrier and the BEV demand.

Lin, Zhenhong [ORNL

2012-01-01T23:59:59.000Z

352

Nanoscale Imaging of Airborne Particles Mike Bogan Stanford PULSE Institute, SLAC National Accelerator Laboratory, 2575 Sand Hill Road,  

NLE Websites -- All DOE Office Websites (Extended Search)

Diagnostics with an X-ray Laser? Lessons from the First Diagnostics with an X-ray Laser? Lessons from the First Nanoscale Imaging of Airborne Particles Mike Bogan Stanford PULSE Institute, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, CA 94025, USA What does airborne particulate matter look like? How do we develop quantitative descriptors for particles of complex morphology? These challenges were highlighted in the NIST workshop report "Aerosol Metrology Needs for Climate Science" (Dec, 2011). Sure, we can capture aerosol particles on surfaces - removing them from their airborne state - and probe them with high resolution optical and chemical imaging tools, but what information do we lose about the airborne particles? How can we follow dynamics? In this talk we will explore these very basic questions and their importance to combustion

353

Methane hydrate distribution from prolonged and repeated formation in natural and compacted sand samples: X-ray CT observations  

SciTech Connect

To study physical properties of methane gas hydrate-bearing sediments, it is necessary to synthesize laboratory samples due to the limited availability of cores from natural deposits. X-ray computed tomography (CT) and other observations have shown gas hydrate to occur in a number of morphologies over a variety of sediment types. To aid in understanding formation and growth patterns of hydrate in sediments, methane hydrate was repeatedly formed in laboratory-packed sand samples and in a natural sediment core from the Mount Elbert Stratigraphic Test Well. CT scanning was performed during hydrate formation and decomposition steps, and periodically while the hydrate samples remained under stable conditions for up to 60 days. The investigation revealed the impact of water saturation on location and morphology of hydrate in both laboratory and natural sediments during repeated hydrate formations. Significant redistribution of hydrate and water in the samples was observed over both the short and long term.

Rees, E.V.L.; Kneafsey, T.J.; Seol, Y.

2010-07-01T23:59:59.000Z

354

Use of Computed X-ray Tomographic Data for Analyzing the Thermodynamics of a Dissociating Porous Sand/Hydrate Mixture  

DOE R&D Accomplishments (OSTI)

X-ray computed tomography (CT) is a method that has been used extensively in laboratory experiments for measuring rock properties and fluid transport behavior. More recently, CT scanning has been applied successfully to detect the presence and study the behavior of naturally occurring hydrates. In this study, we used a modified medical CT scanner to image and analyze the progression of a dissociation front in a synthetic methane hydrate/sand mixture. The sample was initially scanned under conditions at which the hydrate is stable (atmospheric pressure and liquid nitrogen temperature, 77 K). The end of the sample holder was then exposed to the ambient air, and the core was continuously scanned as dissociation occurred in response to the rising temperature. CT imaging captured the advancing dissociation front clearly and accurately. The evolved gas volume was monitored as a function of time. Measured by CT, the advancing hydrate dissociation front was modeled as a thermal conduction problem explicitly incorporating the enthalpy of dissociation, using the Stefan moving-boundary-value approach. The assumptions needed to perform the analysis consisted of temperatures at the model boundaries. The estimated value for thermal conductivity of 2.6 W/m K for the remaining water ice/sand mixture is higher than expected based on conduction alone; this high value may represent a lumped parameter that incorporates the processes of heat conduction, methane gas convection, and any kinetic effects that occur during dissociation. The technique presented here has broad implications for future laboratory and field testing that incorporates geophysical techniques to monitor gas hydrate dissociation.

Freifeld, Barry M.; Kneafsey, Timothy J.; Tomutsa, Liviu; Stern, Laura A.; Kirby, Stephen H.

2002-02-28T23:59:59.000Z

355

Guidebook for the Use of Synfuels in Electric Utility Combustion Systems, Volume 3: Liquid Fuels Derived From Shale and Tar Sands  

Science Conference Proceedings (OSTI)

The properties of liquid fuels derived from oil shales or tar sands differ substantially and in varying degrees from those of conventional petroleum fuels. Utilities will find data and procedures in this guidebook to help them evaluate the modifications those fuels would require in their systems.

1985-08-01T23:59:59.000Z

356

Tonopah test range - outpost of Sandia National Laboratories  

Science Conference Proceedings (OSTI)

Tonopah Test Range is a unique historic site. Established in 1957 by Sandia Corporation, Tonopah Test Range in Nevada provided an isolated place for the Atomic Energy Commission to test ballistics and non-nuclear features of atomic weapons. It served this and allied purposes well for nearly forty years, contributing immeasurably to a peaceful conclusion to the long arms race remembered as the Cold War. This report is a brief review of historical highlights at Tonopah Test Range. Sandia`s Los Lunas, Salton Sea, Kauai, and Edgewood testing ranges also receive abridged mention. Although Sandia`s test ranges are the subject, the central focus is on the people who managed and operated the range. Comments from historical figures are interspersed through the narrative to establish this perspective, and at the end a few observations concerning the range`s future are provided.

Johnson, L.

1996-03-01T23:59:59.000Z

357

Two-Phase Westward Encroachment of Basin and Range Extension...  

Open Energy Info (EERE)

block to >150% in the Wassuk and Singatse Ranges to the east. Geological and apatite fission track data from exhumed upper crustal sections in the Wassuk and Singatse Ranges...

358

Short-Range Ensemble Forecasts of Precipitation Type  

Science Conference Proceedings (OSTI)

Short-range ensemble forecasting is extended to a critical winter weather problem: forecasting precipitation type. Forecast soundings from the operational NCEP Short-Range Ensemble Forecast system are combined with five precipitation-type ...

Matthew S. Wandishin; Michael E. Baldwin; Steven L. Mullen; John V. Cortinas Jr.

2005-08-01T23:59:59.000Z

359

Verification of Eta–RSM Short-Range Ensemble Forecasts  

Science Conference Proceedings (OSTI)

Motivated by the success of ensemble forecasting at the medium range, the performance of a prototype short-range ensemble forecast system is examined. The ensemble dataset consists of 15 case days from September 1995 through January 1996. There ...

Thomas M. Hamill; Stephen J. Colucci

1997-06-01T23:59:59.000Z

360

Geographic Information System At Northern Basin & Range Region...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geographic Information System At Northern Basin & Range Region (Blewitt, Et Al., 2003) Exploration...

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Geographic Information System At Nw Basin & Range Region (Nash...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geographic Information System At Nw Basin & Range Region (Nash & Johnson, 2003) Exploration Activity...

362

Geographic Information System At Northern Basin & Range Region...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geographic Information System At Northern Basin & Range Region (Nash & Johnson, 2003) Exploration Activity...

363

A Low-Power Wide-Linear-Range Transconductance Amplifier  

Science Conference Proceedings (OSTI)

The linear range of approximately ±75 mV of traditional subthreshold transconductance amplifiers is too small for certain applications—for example, for filters in electronic cochleas, where it is desirable to handle loud sounds without ... Keywords: amplifier, cochlea, degeneration, dynamic range, low-power, noise, transconductance, wide-linear-range

Rahul Sarpeshkar; Richard F. Lyon; Carver Mead

1997-05-01T23:59:59.000Z

364

High dynamic range texture compression for graphics hardware  

Science Conference Proceedings (OSTI)

In this paper, we break new ground by presenting algorithms for fixed-rate compression of high dynamic range textures at low bit rates. First, the S3TC low dynamic range texture compression scheme is extended in order to enable compression of HDR data. ... Keywords: graphics hardware, high dynamic range images, image compression, texture compression

Jacob Munkberg; Petrik Clarberg; Jon Hasselgren; Tomas Akenine-Möller

2006-07-01T23:59:59.000Z

365

Tonopah Test Range Post-Closure Inspection Annual Report, Tonopah Test Range, Nevada, Calendar Year 2002  

Science Conference Proceedings (OSTI)

This Post-Closure Inspection Annual Report provides documentation of the semiannual inspections conducted at the following Corrective Action Units (CAU)s: CAU 400: Bomblet Pit and Five Points Landfill; CAU 404: Roller Coaster Lagoons and Trench; CAU 407: Roller Coaster RadSafe Area; CAU 424: Area 3 Landfill Complexes; CAU 426: Cactus Spring Waste Trenches; CAU 427: Septic Waste Systems 2, 6; and CAU 453: Area 9 UXO Landfill, all located at the Tonopah Test Range, Nevada. Post-closure inspections are not required at CAU 400 but are conducted to monitor vegetation and fencing at the site. Site inspections were conducted in May and November 2002. All site inspections were made after Nevada Division of Environmental Protection (NDEP) approval of the appropriate Closure Report (CR), excluding CAU 400 which did not require a CR, and were conducted in accordance with the Post-Closure Inspection Plans in the NDEP-approved CRs. Post-closure inspections conducted during 2002 identified several areas requiring maintenance/repairs. Maintenance work and proposed additional monitoring are included in the appropriate section for each CAU. This report includes copies of the Post-Closure Inspection Plans, Post-Closure Inspection Checklists, copies of the field notes, photographs, and the Post-Closure Vegetative Monitoring Report. The Post-Closure Inspection Plan for each CAU is located in Attachment A. Post-Closure Inspection Checklists are in Attachment B. Copies of the field notes from each inspection are included in Attachment C. Attachment D consists of the photographic logs and photographs of the sites. The post-closure vegetative monitoring report for calendar year 2002 is included in Attachment E.

R. B. Jackson

2003-08-01T23:59:59.000Z

366

Horizontal well construction/completion process in a Gulf of Mexico unconsolidated sand: development of baseline correlations for improved drill-in fluid cleanup practices  

E-Print Network (OSTI)

This thesis examines, in detail, the procedures and practices undertaken in the drilling and completion phases of a Gulf of Mexico horizontal well in an unconsolidated sand. In particular, this thesis presents a detailed case history analysis of well planning, completion and cleanup operations. Our objectives are to present a complete examination of the openhole horizontal well construction/completion process using a new drill-in fluid (DIF). Further, we will establish data critical to development of new cleanup correlation techniques (the continuing goal of the CEA-73 industry consortium). Project results are intended to advance the technology progression of cleanup in horizontal welts by using a "Best Completion Practices'' well to establish a baseline analysis for development of rigsite DIF cleanup correlations. Presented in this thesis are: * Completion specifics of subject well * Audit of horizontal well design/well construction process * Documentation (on-location) of lignite practices * Laboratory analyses of DO cleanup * Well performance analysis Well audit results show that prudent DIF selection requires a thorough understanding of formation and reservoir specifics, along with completion and cleanup operations. Adequate pre-planning by lignite personnel for handling, weather problems, storage/mixing requirements and fluid property maintenance are very important for successful operations using DIF. Proper maintenance of solids control systems is essential for quality control of DIF properties. Detailed well planning by the operator (Vastar Resources), coupled with a conscientious mud service company (TBC-Brinadd, Houston), led to smooth execution of well completion/cleanup operations.aboratory analyses of field DIF samples taken during drilling show that entrained drill solids in DIF can greatly impact mudcaps removal during cleanup. However, well performance was roughly three times original expectations, achieving a stabilized gas flow rate of approximately 34 MMCF/D. Horizontal well decline type curve techniques and a proprietary analysis method developed by Conoco were used to estimate formation properties, using only wellhead production rates and pressures. Using these results, we estimated DIF cupcake removal for various reservoir permeability scenarios. Results suggest that a high percentage of DIF filtercake removal was achieved only if reservoir permeability was less than the permeability range (100-500 md) initially estimated by the operator.

Lacewell, Jason Lawrence

1999-01-01T23:59:59.000Z

367

SAND REPORT SAND2004-1777  

E-Print Network (OSTI)

Operated by Los Alamos National Security, LLC for the U.S. Department of Energy's NNSA UNCLASSIFIED #12;Operated by Los Alamos National Security, LLC for the U.S. Department of Energy's NNSA of Energy's NNSA The Next 20 years ENERGY HEALTH ENVIRONMENT RESOURCES #12;Operated by Los

Walker, Homer F.

368

SAND REPORT SAND2003-0799  

E-Print Network (OSTI)

Investment Fund Regional Revolving Loan Fund RTD Grants (Washington Technology Center) Rural Business

Ho, Cliff

369

SAND REPORT SAND2002-4135  

E-Print Network (OSTI)

in the vicinity of the sensor (see Figure 9). A resistance temperature detector (RTD) on-board the chemiresistor of the Phase II and III tests. The average temperature recorded by the chemiresistor RTD while located

Ho, Cliff

370

SAND REPORT SAND2003-3410  

E-Print Network (OSTI)

Figure 11. Apparatus inside an oven for RTD calibration (two chemiresistor chips and a thermocouple).............................................................................................................26 Figure 12. Calibration of the RTD on the chemiresistor die. Chemiresistor E18 RTD response with and without a constant-voltage heating

Ho, Cliff

371

Spectral Budget Analysis of the Short-Range Forecast Error of the NMC Medium-Range Forecast Model  

Science Conference Proceedings (OSTI)

The budget of the systematic component of the short-range forecast error in the National Meteorological Center's Medium-Range Forecast Model (NMC MRF) is examined. The budget is computed for the spectral coefficients and the variances of ...

Masao Kanamitsu; Suranjana Saha

1995-06-01T23:59:59.000Z

372

SAND2011-6616A Page 1 Session 2: High Energy Density, Plasmas, Magnetic Fields  

National Nuclear Security Administration (NNSA)

616A 616A Page 1 Session 2: High Energy Density, Plasmas, Magnetic Fields Dynamical Materials Experiments on Sandia's Z Machine: Obtaining Data with High Precision at HED Conditions Thomas R. Mattsson and Seth Root Sandia National Laboratories, Albuquerque, NM USA Summary: The Z machine at Sandia National Laboratories has successfully been used to study a wide range of materials under extreme conditions. In this paper, we will discuss the methodology resulting in high-pressure measurements at multi-Mbar pressures as well as present experimental data for shock compression of poly methyl-pentene, a hydrocarbon plastic. Introduction During the last few years, there has been a notable increase in the interest of high-pressure science. The increase in interest has been driven by the remarkable capabilities of new and improved platforms like

373

Seismicity of the Coso Range, California | Open Energy Information  

Open Energy Info (EERE)

of the Coso Range, California of the Coso Range, California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Seismicity of the Coso Range, California Details Activities (1) Areas (1) Regions (0) Abstract: A 16-station seismographic network, approximately 40 km north-south by 30 km east-west, was installed in the Coso Range, California, in September 1975 as part of a geological and geophysical assessment of the geothermal resource potential of range. During the first 2 years of network operations, 4216 local earthquakes (0.5< or =m< or =3.9) defined zones of seismicity that strike radially outward from a Pleistocene rhyolite field located near the center of the Coso Range. Most earthquakes were located in zones showing a general northwest trend across the range.

374

Numerical Modeling of Transient Basin and Range Extensional Geothermal  

Open Energy Info (EERE)

Transient Basin and Range Extensional Geothermal Transient Basin and Range Extensional Geothermal Systems Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Numerical Modeling of Transient Basin and Range Extensional Geothermal Systems Abstract A suite of models utilizing a range of bulkrock permeabilities were developed to analyze thetransient behavior of basin and range extensionalgeothermal systems, and particularly, the evolution ofthe system temperature with time. Each modelconsists of two mountain ranges (~1 km relief fromthe valley floor) separated by a thick sequence (about4 km) of clastic sediments derived from the adjacentranges, and a relatively permeable, high angle faultthat functions as a conduit for subsurface fluids. Thisgeometry is typical of Basin and Range extensionalsystems.We

375

Northwest Basin and Range Geothermal Region | Open Energy Information  

Open Energy Info (EERE)

Northwest Basin and Range Geothermal Region Northwest Basin and Range Geothermal Region Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Northwest Basin and Range Geothermal Region Details Areas (48) Power Plants (8) Projects (15) Techniques (33) The Basin and Range Province in northwestern Nevada and northeastern California is characterized by late Cretaceous - early Cenozoic regional erosion, Oligocene - Miocene volcanism, and subsequent late Miocene extension. Extensional faulting in northwestern Nevada began everywhere at 12 Ma and has continued up to the present. Faulting in the Warner Range in northeastern California can only be constrained to have begun between 14 and 3 Ma, but may represent westward migration of Basin and Range extension during the Pliocene. Compared to the many parts of the Basin and Range in

376

Rock matrix and fracture analysis of flow in western tight gas sands  

SciTech Connect

Advanced core analysis includes measurements on the matrix properties of the rock. Matrix properties are important even in fractured wells since it is these properties which determine the rate of gas flow into the fractures. Cores are being tested from the fluvial, coastal, and paludal zones of the Mesaverde. At least two cores from each of these zones from all three wells will be analyzed. Properties measured include permeability as a function of confining pressure over the range of 500 to 5000 psi. A minimum of two Klinkenberg permeabilities are being determined from at least five data points. Interpretation includes estimates of pore size from gas slippage. Water adsorption and desorption isotherms will be determined for selected samples with data points being obtained at the following relative humidities: 0, 20, 40, 60, 75, 90, 92, 95 and 98. Porosity measurements from both thin section examination and volumetric measurements are being made. These results will be compared with the porosities of the cored internals determined from logs.

Morrow, N.R.; Brower, K.R.; Ward, J.S.

1985-01-01T23:59:59.000Z

377

Multispectral Imaging At Rangely Oilfield Area (Pickles & Cover, 2004) |  

Open Energy Info (EERE)

Multispectral Imaging At Rangely Oilfield Area (Pickles & Cover, 2004) Multispectral Imaging At Rangely Oilfield Area (Pickles & Cover, 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Rangely Oilfield Area (Pickles & Cover, 2004) Exploration Activity Details Location Rangely Oilfield Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Airborne hyperspectral imaging applied to determine vegetation and CO2 leakage in the Rangely oilfield of northwest Colorado - results may be useful for geothermal exploration. References W. Pickles, W. Cover (2004) Hyperspectral Geobotanical Remote Sensing For Co2 Storage Monitoring Retrieved from "http://en.openei.org/w/index.php?title=Multispectral_Imaging_At_Rangely_Oilfield_Area_(Pickles_%26_Cover,_2004)&oldid=511013"

378

Southern Basin and Range Geothermal Region | Open Energy Information  

Open Energy Info (EERE)

Basin and Range Geothermal Region Basin and Range Geothermal Region Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Southern Basin and Range Geothermal Region Details Areas (0) Power Plants (0) Projects (0) Techniques (0) Map: {{{Name}}} North-south-striking and west-dipping Basin and Range province normal faults form the western edge of the Sierra Madre Occidental plateau in northeastern Sonora. These faults and associated half-grabens extend over a distance of more than 300 km between the San Bernardino basin in the north and the Sahuaripa basin in the south. Active Tectonics of Northeastern Sonora, Mexico (Southern Basin and Range Province) and the 3 May 1887 Mw 7.4 Earthquake [1] References ↑ "Active Tectonics of Northeastern Sonora, Mexico (Southern Basin and Range Province) and the 3 May 1887 Mw 7.4 Earthquake"

379

Steady state deformation of the Coso Range, east central California...  

Open Energy Info (EERE)

Steady state deformation of the Coso Range, east central California, inferred from satellite radar interferometry Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home...

380

Modeling-Computer Simulations At Nevada Test And Training Range...  

Open Energy Info (EERE)

Page Edit History Facebook icon Twitter icon Modeling-Computer Simulations At Nevada Test And Training Range Area (Sabin, Et Al., 2004) Jump to: navigation, search GEOTHERMAL...

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Developing National Long-Range Nuclear Energy Strategies (INPRO...  

NLE Websites -- All DOE Office Websites (Extended Search)

"Developing National Long-Range Nuclear Energy Strategies (INPRO)" workshop (Aug. 8-19, 2011) Director's Welcome Organization Achievements Highlights Fact Sheets, Brochures & Other...

382

Hydrothermal Heat Discharge In The Cascade Range, Northwestern...  

Open Energy Info (EERE)

Hydrothermal heat discharge in the Cascade Range includes the heat discharged by thermal springs, by "slightly thermal" springs that are only a few degrees warmer than...

383

Geothermal Resource Analysis and Structure of Basin and Range...  

Open Energy Info (EERE)

Energy, 2003 DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for Geothermal Resource Analysis and Structure of Basin and Range Systems,...

384

Exploration and Development Techniques for Basin and Range Geothermal...  

Open Energy Info (EERE)

Council, 2002 DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for Exploration and Development Techniques for Basin and Range Geothermal...

385

A study of electric vehicle charging patterns and range anxiety.  

E-Print Network (OSTI)

?? Range anxiety is a relatively new concept which is defined as the fear of running out of power when driving an electric vehicle. To… (more)

Knutsen, Daniel

2013-01-01T23:59:59.000Z

386

The Extended Q-Range Small Angle Neutron Scattering ...  

Science Conference Proceedings (OSTI)

Abstract Scope, The Extended Q-Range Small Angle Neutron Scattering Diffractometer (EQ-SANS) at the Spallation Neutron Source (SNS) is a high intensity ...

387

Indonesia-Bringing a Range of Supported Mitigation Activities...  

Open Energy Info (EERE)

Page Edit with form History Facebook icon Twitter icon Indonesia-Bringing a Range of Supported Mitigation Activities in Selected Countries to the Next Level Jump to: navigation,...

388

Long-Range Transport and Global Fractionation of Persistent Organic...  

NLE Websites -- All DOE Office Websites (Extended Search)

Long-Range Transport and Global Fractionation of Persistent Organic Pollutants: Insights from Multimedia Modeling Studies Speaker(s): Martin Scheringer Date: July 10, 2003 -...

389

Idaho National Laboratory Stand-Off Experiment Range draft environment...  

NLE Websites -- All DOE Office Websites (Extended Search)

News Media Contact: Tim Jackson (208) 526-8484 For Immediate Release December 22, 2010 Idaho National Laboratory Stand-Off Experiment Range draft environmental assessment...

390

Geographic Information System At Nw Basin & Range Region (Coolbaugh...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geographic Information System At Nw Basin & Range Region (Coolbaugh, Et Al., 2005 - 2) Exploration...

391

Geographic Information System At Northern Basin & Range Region...  

Open Energy Info (EERE)

Login | Sign Up Search Page Edit History Facebook icon Twitter icon Geographic Information System At Northern Basin & Range Region (Coolbaugh, Et Al., 2005 - 2) Jump to:...

392

Geographic Information System At Nw Basin & Range Region (Blewitt...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geographic Information System At Nw Basin & Range Region (Blewitt, Et Al., 2003) Exploration Activity...

393

Structure, tectonics and stress field of the Coso Range, Inyo...  

Open Energy Info (EERE)

as having arcuate and ring faults both suggesting the presence of a circumscribed subsidence bowl or calderalike feature. New information suggests the Coso Range is situated in...

394

Thermal Gradient Holes At Northern Basin & Range Region (Pritchett...  

Open Energy Info (EERE)

Date Usefulness not useful DOE-funding Unknown Notes NOTE: These are theoreticalcomputer simulation tests of various methods on eight hypothetical 'model' basing-and-range...

395

Direct-Current Resistivity Survey At Northern Basin & Range Region...  

Open Energy Info (EERE)

Activity Date Usefulness useful DOE-funding Unknown Notes NOTE: These are theoreticalcomputer simulation tests of various methods on eight hypothetical 'model' basing-and-range...

396

Modeling-Computer Simulations At Northern Basin & Range Region...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Modeling-Computer Simulations At Northern Basin & Range Region (Blackwell, Et Al., 2003) Exploration...

397

Modeling-Computer Simulations At Nw Basin & Range Region (Pritchett...  

Open Energy Info (EERE)

Login | Sign Up Search Page Edit History Facebook icon Twitter icon Modeling-Computer Simulations At Nw Basin & Range Region (Pritchett, 2004) Jump to: navigation, search...

398

Direct-Current Resistivity Survey At Nw Basin & Range Region...  

Open Energy Info (EERE)

Activity Date Usefulness useful DOE-funding Unknown Notes NOTE: These are theoreticalcomputer simulation tests of various methods on eight hypothetical 'model' basing-and-range...

399

Modeling-Computer Simulations At Nw Basin & Range Region (Biasi...  

Open Energy Info (EERE)

Modeling-Computer Simulations At Nw Basin & Range Region (Biasi, Et Al., 2009) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Modeling-Computer...

400

Key Property of Graphene Sustained Over Wide Ranges of ...  

Science Conference Proceedings (OSTI)

... a proportional relationship between energy and momentum ... an unexpectedly broad range of energies and densities ... that when the density of carriers ...

2012-11-14T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Seismicity and seismic stress in the Coso Range, Coso geothermal...  

Open Energy Info (EERE)

California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Book: Seismicity and seismic stress in the Coso Range, Coso geothermal field, and Indian...

402

Data Acquisition-Manipulation At Northern Basin & Range Region...  

Open Energy Info (EERE)

Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon Data Acquisition-Manipulation At Northern Basin & Range Region (Coolbaugh, Et Al., 2005 - 2)...

403

Data Acquisition-Manipulation At Nw Basin & Range Region (Coolbaugh...  

Open Energy Info (EERE)

Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon Data Acquisition-Manipulation At Nw Basin & Range Region (Coolbaugh, Et Al., 2005 - 2) Jump...

404

ORISE: Nuclear engineering degrees at highest ranges since 1980s  

NLE Websites -- All DOE Office Websites (Extended Search)

ORISE report shows graduation, enrollment rates for nuclear engineering candidates are still at highest ranges reported since 1980s Report also shows shifts in career opportunities...

405

Tonopah Test Range Environmental Restoration Corrective Action Sites  

SciTech Connect

This report describes the status (closed, closed in place, or closure in progress) of the Corrective Action Sites and Corrective Action Units at the Tonopah Test Range

NSTec Environmental Restoration

2010-08-04T23:59:59.000Z

406

Aerial Photography At Nevada Test And Training Range Area (Sabin...  

Open Energy Info (EERE)

Nevada Test And Training Range Area (Sabin, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Aerial Photography At Nevada Test And...

407

Geographic Information System At Nevada Test And Training Range...  

Open Energy Info (EERE)

Page Edit History Facebook icon Twitter icon Geographic Information System At Nevada Test And Training Range Area (Sabin, Et Al., 2004) Jump to: navigation, search GEOTHERMAL...

408

Geothermometry At Nevada Test And Training Range Area (Sabin...  

Open Energy Info (EERE)

Nevada Test And Training Range Area (Sabin, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geothermometry At Nevada Test And...

409

BSA 11-10: High Dynamic Range Measurements with Delayed ...  

... then the dynamic range of the system is set by the voltage ... The new circuit design will advance technology used in industrial automation, ... B ...

410

High Speed High Dynamic Range High Accuracy Measurement System  

Disclosure Number 201102747 Technology Summary The present invention measures a beam of protons that has a high dynamic range. Typically, one uses ...

411

Micro-Earthquake At Northwest Basin and Range Geothermal Region...  

Open Energy Info (EERE)

to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Micro-Earthquake At Northwest Basin and Range Geothermal Region (1976) Exploration Activity Details...

412

Seasonal home ranges and migration of red deer (Cervus elaphus).  

E-Print Network (OSTI)

??1. Many studies have dealt with home range and migratory patterns of Cervid species, but there are few explicit analyses quantifying migratory patterns and home… (more)

Kleveland, Kirsten

2007-01-01T23:59:59.000Z

413

Variable Range Hopping Conduction and Magnetic Properties of ...  

Science Conference Proceedings (OSTI)

The electrical resistivities have been measured over a wide range of temperature (5-285K), suggesting semiconductor behavior. The charge transport ...

414

Geodetic Survey At Nevada Test And Training Range Area (Sabin...  

Open Energy Info (EERE)

Page Edit History Facebook icon Twitter icon Geodetic Survey At Nevada Test And Training Range Area (Sabin, Et Al., 2004) Jump to: navigation, search GEOTHERMAL...

415

Distribution of quaternary rhyolite dome of the Coso Range, California...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Distribution of quaternary rhyolite dome of the Coso Range, California: Implications for extent...

416

Characterization and utilization of hydrotreated products produced from the Whiterocks (Utah) tar sand bitumen-derived liquid  

SciTech Connect

The bitumen-derived liquid produced in a 4-inch diameter fluidized-bed reactor from the mined and crushed ore from the Whiterocks tar sand deposit has been hydrotreated in a fixed-bed reactor. The purpose was to determine the extent of upgrading as a function of process operating variable. A sulfided nickel-molybendum on alumina hydrodenitrogenation catalyst was used in all experiments. Moderately severe operating conditions were employed; that is, high reaction temperature (617--680 K) high reactor pressure (11.0--17.1 MPa) and low liquid feed rate (0.18--0.77 HSV); to achieve the desired reduction in heteroatom content. Detailed chemical structures of the bitumen-derived liquid feedstock and the hydrotreated total liquid products were determined by high resolution gas chromatography - mass spectrometry analyses. The compounds identified in the native bitumen included isoprenoids; bicyclic, tricycle, and tetracyclic terpenoids; steranes; hopanes; and perhydro-{beta}-carotenes. In addition, normal and branched alkanes and alkenes and partially dehydrogenated hydroaromatics were identified in the bitumen-derived liquid. The dominant pyrolysis reactions were: (1) the dealkylation of long alkyl side chains to form {alpha} - and isoolefins; and (2) the cleavage of alkyl chains linking aromatic and hydroaromatic clusters. Olefinic bonds were not observed in the hydrotreated product and monoaromatic hydrocarbons were the predominant aromatic species. The properties of the jet fuel fractions from the hydrotreated products met most of the jet fuel specifications. The cetane indices indicated these fractions would be suitable for use as diesel fuels.

Tsai, C.H.; Longstaff, D.C.; Deo, M.D.; Hanson, F.V.; Oblad, A.G.

1991-12-31T23:59:59.000Z

417

Constitutive models for the Etchegoin Sands, Belridge Diatomite, and overburden formations at the Lost Hills oil field, California  

SciTech Connect

This report documents the development of constitutive material models for the overburden formations, reservoir formations, and underlying strata at the Lost Hills oil field located about 45 miles northwest of Bakersfield in Kern County, California. Triaxial rock mechanics tests were performed on specimens prepared from cores recovered from the Lost Hills field, and included measurements of axial and radial stresses and strains under different load paths. The tested intervals comprise diatomaceous sands of the Etchegoin Formation and several diatomite types of the Belridge Diatomite Member of the Monterey Formation, including cycles both above and below the diagenetic phase boundary between opal-A and opal-CT. The laboratory data are used to drive constitutive parameters for the Extended Sandler-Rubin (ESR) cap model that is implemented in Sandia's structural mechanics finite element code JAS3D. Available data in the literature are also used to derive ESR shear failure parameters for overburden formations. The material models are being used in large-scale three-dimensional geomechanical simulations of the reservoir behavior during primary and secondary recovery.

FOSSUM,ARLO F.; FREDRICH,JOANNE T.

2000-04-01T23:59:59.000Z

418

Linguistic facts as predicates over ranges of the sentence  

Science Conference Proceedings (OSTI)

This paper introduces a novel approach to language processing, in which linguistic facts are represented as predicates over ranges of the intput text, usually, but not limited to, ranges of the current sentence. Such an approch allows to build non-linear ...

Benoît Sagot

2005-04-01T23:59:59.000Z

419

Long Range Passive UHF RFID System Using HVAC Ducts  

E-Print Network (OSTI)

INVITED P A P E R Long Range Passive UHF RFID System Using HVAC Ducts To provide a potential communications channel, HVAC ducts can function as electromagnetic waveguides; a 30-m read range has been-conditioning (HVAC) ducts as a potential communication channel between passive ultrahigh-frequency (UHF) radio

Hochberg, Michael

420

Renewable Energy and the Nevada Test and Training Range  

E-Print Network (OSTI)

1 Renewable Energy and the Nevada Test and Training Range Wednesday, December 15, 2010 Melissa due to renewable energy infrastructure development at the Nevada Test and Training Range. Nevada has have ever-increasing renewable energy goals. However, proposals for the development of 116 renewable

Lewis, Robert Michael

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Energy Distribution Control in Wireless Sensor Networks Through Range Optimization  

E-Print Network (OSTI)

Energy Distribution Control in Wireless Sensor Networks Through Range Optimization M.Sarper Gokturk a location-based routing framework to control the energy distribution in a network where transmission ranges--A major objective in wireless sensor networks is to find optimum routing strategies for energy efficient

Yanikoglu, Berrin

422

SRNSSTI200900446 Evaluation of Range Estimates for Toyota FCHVadv  

E-Print Network (OSTI)

200900446 Evaluation of Range Estimates for Toyota FCHVadv Under Open Road Driving Conditions Keith Wipke driving ranges of >400 miles announced by Toyota for its new advanced Fuel Cell Hybrid Vehicle (FCHVadvvehicle evaluation with Toyota Motor Engineering & Manufacturing North America, Inc. (TEMA) over a typical

423

Range-free mobile node localization using static anchor  

Science Conference Proceedings (OSTI)

In this paper we have proposed a deterministic, range-free, distributed localization algorithm for mobile sensor nodes with static anchors. Mobile node calculates its approximate line of movement and corresponding position based on received beacons from ... Keywords: beacon point, line of movement, mobile sensor localization, range-free

Kaushik Mondal, Partha Sarathi Mandal

2013-08-01T23:59:59.000Z

424

Geologic investigation of Playa Lakes, Tonopah Test Range, Nevada : data report.  

SciTech Connect

Subsurface geological investigations have been conducted at two large playa lakes at the Tonopah Test Range in central Nevada. These characterization activities were intended to provide basic stratigraphic-framework information regarding the lateral distribution of ''hard'' and ''soft'' sedimentary materials for use in defining suitable target regions for penetration testing. Both downhole geophysical measurements and macroscopic lithilogic descriptions were used as a surrogate for quantitative mechanical-strength properties, although some quantitative laboratory strength measurements were obtained as well. Both rotary (71) and core (19) holes on a systematic grid were drilled in the southern half of the Main Lake; drill hole spacings are 300 ft north-south and 500-ft east-west. The drilled region overlaps a previous cone-penetrometer survey that also addressed the distribution of hard and soft material. Holes were drilled to a depth of 40 ft and logged using both geologic examination and down-hole geophysical surveying. The data identify a large complex of very coarse-grained sediment (clasts up to 8 mm) with interbedded finer-grained sands, silts and clays, underlying a fairly uniform layer of silty clay 6 to 12 ft thick. Geophysical densities of the course-grained materials exceed 2.0 g/cm{sup 2}, and this petrophysical value appears to be a valid discriminator of hard vs. soft sediments in the subsurface. Thirty-four holes, including both core and rotary drilling, were drilled on a portion of the much larger Antelope Lake. A set of pre-drilling geophysical surveys, including time-domain electromagnetic methods, galvanic resistivity soundings, and terrain-conductivity surveying, was used to identify the gross distribution of conductive and resistive facies with respect to the present lake outline. Conductive areas were postulated to represent softer, clay-rich sediments with larger amounts of contained conductive ground water. Initial drilling, consisting of cored drill holes to 100-ft (33-m) depth, confirmed both the specific surface geophysical measurements and the more general geophysical model of the subsurface lake facies. Good agreement of conductive regions with drill holes containing little to no coarse-grained sediments was observed, and vice-versa. A second phase of grid drilling on approximately 300-ft (100-m) centers was targeted a delineating a region of sufficient size containing essentially no coarse-grained ''hard'' material. Such a region was identified in the southwestern portion of Antelope Lake.

Rautman, Christopher Arthur

2004-12-01T23:59:59.000Z

425

Geothermal Reservoir Assessment Case Study, Northern Basin and Range  

Open Energy Info (EERE)

Reservoir Assessment Case Study, Northern Basin and Range Reservoir Assessment Case Study, Northern Basin and Range Province, Northern Dixie Valley, Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Geothermal Reservoir Assessment Case Study, Northern Basin and Range Province, Northern Dixie Valley, Nevada Abstract N/A Authors Elaine J. Bell, Lawrence T. Larson and Russell W. Juncal Published U.S. Department of Energy, 1980 Report Number GLO2386 DOI Not Provided Check for DOI availability: http://crossref.org Online Internet link for Geothermal Reservoir Assessment Case Study, Northern Basin and Range Province, Northern Dixie Valley, Nevada Citation Elaine J. Bell,Lawrence T. Larson,Russell W. Juncal. 1980. Geothermal Reservoir Assessment Case Study, Northern Basin and Range Province,

426

A range description for the planar circular Radon transform  

E-Print Network (OSTI)

The transform considered in the paper integrates a function supported in the unit disk on the plane over all circles centered at the boundary of this disk. Such circular Radon transform arises in several contemporary imaging techniques, as well as in other applications. As it is common for transforms of Radon type, its range has infinite co-dimension in standard function spaces. Range descriptions for such transforms are known to be very important for computed tomography, for instance when dealing with incomplete data, error correction, and other issues. A complete range description for the circular Radon transform is obtained. Range conditions include the recently found set of moment type conditions, which happens to be incomplete, as well as the rest of conditions that have less standard form. In order to explain the procedure better, a similar (non-standard) treatment of the range conditions is described first for the usual Radon transform on the plane.

Gaik Ambartsoumian; Peter Kuchment

2005-08-04T23:59:59.000Z

427

Magnetotellurics At Northern Basin & Range Region (Pritchett, 2004) | Open  

Open Energy Info (EERE)

Magnetotellurics At Northern Basin & Range Region Magnetotellurics At Northern Basin & Range Region (Pritchett, 2004) Exploration Activity Details Location Northern Basin and Range Geothermal Region Exploration Technique Magnetotellurics Activity Date Usefulness useful DOE-funding Unknown Notes NOTE: These are theoretical/computer simulation tests of various methods on eight hypothetical 'model' basing-and-range geothermal systems. "The 300-meter heat flow holes are essentially useless for finding the "hidden" reservoirs. Clearly, the best results are obtained from the SP and MT surveys, with DC resistivity a close third. It is concluded that the best way to find "hidden" basin and range geothermal resources of this general type is to carry out simultaneous SP and low-frequency MT surveys, and then

428

Range Design Criteria - June 4, 2012 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Range Design Criteria - June 4, 2012 Range Design Criteria - June 4, 2012 Range Design Criteria - June 4, 2012 June 4, 2012 This document contains the currently-approved firearms "Range Design Criteria" referred to on DOE O 473.3, Protection Program Operations PURPOSE. This document contains design criteria for U.S. Department of Energy (DOE) live-fire ranges for use in planning new facilities and major rehabilitation of existing facilities. This document will be approved and maintained by the Office of Security, Office of Health, Safety and Security (HSS) as a stand-alone document on the HSS website: http://www.hss.doe.gov/SecPolicy/pfs.html. PLANNING FACTORS. All applicable local, State, Federal, U.S. Environmental Protection Agency, Occupational Health and Safety Administration (OSHA),

429

Geographic Information System At Nevada Test And Training Range Area  

Open Energy Info (EERE)

Geographic Information System At Nevada Test And Training Range Area Geographic Information System At Nevada Test And Training Range Area (Sabin, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geographic Information System At Nevada Test And Training Range Area (Sabin, Et Al., 2004) Exploration Activity Details Location Nevada Test And Training Range Area Exploration Technique Geographic Information System Activity Date Usefulness not indicated DOE-funding Unknown Notes Nellis Air Force Range (NAFR) occupies over 3 million acres in southern Nevada (Figure 1). We recently assessed potential utility-grade geothermal resources and possible target areas for exploration by constructing a GIS of this area and applying the occurrence model ideas outlined above (ITSI, 2003; Sabin et al., 2004). We list below many of the factors considered.

430

NNSA Celebrates Earth Week: Pantex 'greens' firing range | National Nuclear  

NLE Websites -- All DOE Office Websites (Extended Search)

'greens' firing range | National Nuclear 'greens' firing range | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Home > NNSA Blog > NNSA Celebrates Earth Week: Pantex 'greens' firing range NNSA Celebrates Earth Week: Pantex 'greens' firing range Posted By Greg Cunningham, Pantex The lead that flies at the Pantex Firing Range has to land somewhere, and

431

Aeromagnetic and gravity surveys in the Coso Range, California | Open  

Open Energy Info (EERE)

and gravity surveys in the Coso Range, California and gravity surveys in the Coso Range, California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Aeromagnetic and gravity surveys in the Coso Range, California Details Activities (2) Areas (1) Regions (0) Abstract: The effect of an underlying magma reservoir cannot be identified within the complex gravity pattern in the Coso Range, California. Rather, linear gravity contours, which suggest a regional tectonic origin, enclose the location of most of the volcanic activity of the Coso Range. Faults along the edges of northwest trending, magnetic blocks probably provided paths of minimum resistance to the ascending viscous magma that was extruded as rhyolite domes. Dense, magnetic rocks associated with a complex mafic pluton 9 km in diameter form a relatively impermeable north border of

432

Laser Ranging for Gravitational, Lunar, and Planetary Science  

E-Print Network (OSTI)

More precise lunar and Martian ranging will enable unprecedented tests of Einstein's theory of General Relativity and well as lunar and planetary science. NASA is currently planning several missions to return to the Moon, and it is natural to consider if precision laser ranging instruments should be included. New advanced retroreflector arrays at carefully chosen landing sites would have an immediate positive impact on lunar and gravitational studies. Laser transponders are currently being developed that may offer an advantage over passive ranging, and could be adapted for use on Mars and other distant objects. Precision ranging capability can also be combined with optical communications for an extremely versatile instrument. In this paper we discuss the science that can be gained by improved lunar and Martian ranging along with several technologies that can be used for this purpose.

Stephen M. Merkowitz; Philip W. Dabney; Jeffrey C. Livas; Jan F. McGarry; Gregory A. Neumann; Thomas W. Zagwodzki

2007-12-20T23:59:59.000Z

433

Nevada Test And Training Range Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Nevada Test And Training Range Geothermal Area Nevada Test And Training Range Geothermal Area (Redirected from Nevada Test And Training Range Area) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Nevada Test And Training Range Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (0) 9 Exploration Activities (5) 10 References Area Overview Geothermal Area Profile Location: Nevada Exploration Region: Northern Basin and Range Geothermal Region GEA Development Phase: 2008 USGS Resource Estimate Mean Reservoir Temp: Estimated Reservoir Volume: Mean Capacity: Click "Edit With Form" above to add content

434

System and process for the abatement of casting pollution, reclaiming resin bonded sand, and/or recovering a low Btu fuel from castings  

DOE Patents (OSTI)

Air is caused to flow through the resin bonded mold to aid combustion of the resin binder to form a low Btu gas fuel. Casting heat is recovered for use in a waste heat boiler or other heat abstraction equipment. Foundry air pollutis reduced, the burned portion of the molding sand is recovered for immediate reuse and savings in fuel and other energy is achieved. 5 figs.

Scheffer, K.D.

1984-07-03T23:59:59.000Z

435

Colloid Transport and Deposition in Water-Saturated and Unsaturated Sand and Yucca Mountain Tuff: Effect of Ionic Strength and Moisture Saturation  

Science Conference Proceedings (OSTI)

Colloid-aided radionuclide transport has been considered a potentially important mechanism for the candidate spent fuel and high level waste (HLW) repository at Yucca Mountain. This mechanism, however, has not been treated in Yucca Mountain Total System Performance Assessments (TSPAs) until recently. Even then there has been little discussion of possible colloid retention in the unsaturated zone. This report summarizes investigations of potential colloid retention in sand and Yucca Mountain tuff as a fun...

1999-12-03T23:59:59.000Z

436

Coal-sand attrition system and its` importance in fine coal cleaning. Eighth quarterly report, June 1, 1992--August 31, 1993  

SciTech Connect

The research efforts on the importance of a coal-sand attrition continued with work in four categories: Continuous grinding tests using steel media; fracture tests on coal samples compacted at different pressure; SEM-Image analysis of feed and ground product coal samples; zeta potential measurements of coal samples ground by different media, and flotation test of coal samples ground by different media. Results are described.

Mehta, R.K.; Schultz, C.W.

1993-08-26T23:59:59.000Z

437

System and process for the abatement of casting pollution, reclaiming resin bonded sand, and/or recovering a low BTU fuel from castings  

DOE Patents (OSTI)

Air is caused to flow through the resin bonded mold to aid combustion of the resin binder to form a low BTU gas fuel. Casting heat is recovered for use in a waste heat boiler or other heat abstraction equipment. Foundry air pollution is reduced, the burned portion of the molding sand is recovered for immediate reuse and savings in fuel and other energy is achieved.

Scheffer, Karl D. (121 Governor Dr., Scotia, NY 12302)

1984-07-03T23:59:59.000Z

438

Oil shale, tar sand, coal research, advanced exploratory process technology, jointly sponsored research. Quarterly technical progress report, January--March 1993  

SciTech Connect

Accomplishments for the past quarter are briefly described for the following areas of research: oil shale; tar sand; coal; advanced exploratory process technology; and jointly sponsored research. Oil shale and tar sand researches cover processing studies. Coal research includes: coal combustion; integrated coal processing concepts; and solid waste management. Advanced exploratory process technology covers: advanced process concepts; advanced mitigation concepts; and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; CROW{sup TM} field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO{sub 2} HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid-state NMR analysis of Mesaverde Group, Greater Green River Basin tight gas sands; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced oil recovery techniques; surface process study for oil recovery using a thermal extraction process; oil field waste cleanup using tank bottom recovery process; remote chemical sensor development; in situ treatment of manufactured gas plant contaminated soils demonstration program; solid-state NMR analysis of naturally and artificially matured kerogens; and development of an effective method for the clean-up of natural gas.

1993-09-01T23:59:59.000Z

439

Oil shale, tar sand, coal research advanced exploratory process technology, jointly sponsored research. Quarterly technical progress report, October--December 1992  

SciTech Connect

Accomplishments for the past quarter are presented for the following five tasks: oil shale; tar sand; coal; advanced exploratory process technology; and jointly sponsored research. Oil shale research covers oil shale process studies. Tar sand research is on process development of Recycle Oil Pyrolysis and Extraction (ROPE) Process. Coal research covers: coal combustion; integrated coal processing concepts; and solid waste management. Advanced exploratory process technology includes: advanced process concepts;advanced mitigation concepts; and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; CROW field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; PGI demonstration project; operation and evaluation of the CO{sub 2} HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesaverde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced oil recovery techniques; surface process study for oil recovery using a thermal extraction process; NMR analysis of samples from the ocean drilling program; in situ treatment of manufactured gas plant contaminated soils demonstration program; and solid state NMR analysis of naturally and artificially matured kerogens.

Speight, J.G.

1992-12-31T23:59:59.000Z

440

Hydraulic fracture model and diagnostics verification at GRI/DOE multi-site projects and tight gas sand program support. Final report, July 28, 1993--February 28, 1997  

Science Conference Proceedings (OSTI)

The Mesaverde Group of the Piceance Basin in western Colorado has been a pilot study area for government-sponsored tight gas sand research for over twenty years. Early production experiments included nuclear stimulations and massive hydraulic fracture treatments. This work culminated in the US Department of Energy (DOE)`s Multiwell Experiment (MWX), a field laboratory designed to study the reservoir and production characteristics of low permeability sands. A key feature of MWX was an infrastructure which included several closely spaced wells that allowed detailed characterization of the reservoir through log and core analysis, and well testing. Interference and tracer tests, as well as the use of fracture diagnostics gave further information on stimulation and production characteristics. Thus, the Multiwell Experiment provided a unique opportunity for identifying the factors affecting production from tight gas sand reservoirs. The purpose of this operation was to support the gathering of field data that may be used to resolve the number of unknowns associated with measuring and modeling the dimensions of hydraulic fractures. Using the close-well infrastructure at the Multiwell Site near Rifle, Colorado, this operation focused primarily on the field design and execution of experiments. The data derived from the experiments were gathered and analyzed by DOE team contractors.

Schroeder, J.E.

1997-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Oil shale, tar sand, coal research, advanced exploratory process technology jointly sponsored research. Quarterly technical progress report, April--June 1992  

SciTech Connect

Accomplishments for the quarter are presented for the following areas of research: oil shale, tar sand, coal, advanced exploratory process technology, and jointly sponsored research. Oil shale research includes; oil shale process studies, environmental base studies for oil shale, and miscellaneous basic concept studies. Tar sand research covers process development. Coal research includes; underground coal gasification, coal combustion, integrated coal processing concepts, and solid waste management. Advanced exploratory process technology includes; advanced process concepts, advanced mitigation concepts, and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO{sub 2} HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesa Verde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced recovery techniques; and menu driven access to the WDEQ Hydrologic Data Management Systems.

1992-12-01T23:59:59.000Z

442

Long range Energy Alternatives Planning (LEAP) System | Open Energy  

Open Energy Info (EERE)

Long range Energy Alternatives Planning (LEAP) System Long range Energy Alternatives Planning (LEAP) System Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Long range Energy Alternatives Planning System Agency/Company /Organization: Stockholm Environment Institute Sector: Climate, Energy Focus Area: Non-renewable Energy, Agriculture, Biomass, - Anaerobic Digestion, - Biofuels, - Biomass Combustion, - Biomass Gasification, - Biomass Pyrolysis, - Landfill Gas, - Waste to Energy, Buildings, Economic Development, Energy Efficiency, - Central Plant, Food Supply, Forestry, Geothermal, Goods and Materials, - Embodied Energy, - Materials, Greenhouse Gas, Ground Source Heat Pumps, Hydrogen, Industry, - Industrial Processes, Offsets and Certificates, People and Policy, Solar, - Concentrating Solar Power, - Solar Hot Water, - Solar PV, - Solar Ventilation Preheat, Transportation, Water Conservation, Water Power, Wind

443

Nevada Test And Training Range Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » Nevada Test And Training Range Geothermal Area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermal Resource Area: Nevada Test And Training Range Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3 Regulatory and Environmental Issues 4 Exploration History 5 Well Field Description 6 Geology of the Area 7 Geofluid Geochemistry 8 NEPA-Related Analyses (0) 9 Exploration Activities (5) 10 References Area Overview Geothermal Area Profile Location: Nevada Exploration Region: Northern Basin and Range Geothermal Region GEA Development Phase: 2008 USGS Resource Estimate Mean Reservoir Temp: Estimated Reservoir Volume: Mean Capacity: Click "Edit With Form" above to add content

444

Long range Energy Alternatives Planning (LEAP) System | Open Energy  

Open Energy Info (EERE)

Long range Energy Alternatives Planning (LEAP) System Long range Energy Alternatives Planning (LEAP) System (Redirected from LEAP) Jump to: navigation, search Tool Summary Name: Long range Energy Alternatives Planning System Agency/Company /Organization: Stockholm Environment Institute Sector: Climate, Energy Focus Area: Non-renewable Energy, Agriculture, Biomass, - Anaerobic Digestion, - Biofuels, - Biomass Combustion, - Biomass Gasification, - Biomass Pyrolysis, - Landfill Gas, - Waste to Energy, Buildings, Economic Development, Energy Efficiency, - Central Plant, Food Supply, Forestry, Geothermal, Goods and Materials, - Embodied Energy, - Materials, Greenhouse Gas, Ground Source Heat Pumps, Hydrogen, Industry, - Industrial Processes, Offsets and Certificates, People and Policy, Solar, - Concentrating Solar Power, - Solar Hot Water, - Solar PV, - Solar Ventilation Preheat, Transportation, Water Conservation, Water Power, Wind

445

Short-range force between two Higgs bosons  

E-Print Network (OSTI)

The $S$-wave scattering length and the effective range of the Higgs boson in Standard Model are studied using effective-field-theory approach. After incorporating the first-order electroweak correction, the short-range force between two Higgs bosons remains weakly attractive for $M_H=126$ GeV. It is interesting to find that the force range is about two order-of-magnitude larger than the Compton wavelength of the Higgs boson, almost comparable with the typical length scale of the strong interaction.

Feng Feng; Yu Jia; Wen-Long Sang

2013-12-06T23:59:59.000Z

446

Clutter in the GMTI range-velocity map.  

SciTech Connect

Ground Moving Target Indicator (GMTI) radar maps echo data to range and range-rate, which is a function of a moving target's velocity and its position within the antenna beam footprint. Even stationary clutter will exhibit an apparent motion spectrum and can interfere with moving vehicle detections. Consequently it is very important for a radar to understand how stationary clutter maps into radar measurements of range and velocity. This mapping depends on a wide variety of factors, including details of the radar motion, orientation, and the 3-D topography of the clutter.

Doerry, Armin Walter

2009-04-01T23:59:59.000Z

447

Characteristics of Basin and Range Geothermal Systems with Fluid  

Open Energy Info (EERE)

Characteristics of Basin and Range Geothermal Systems with Fluid Characteristics of Basin and Range Geothermal Systems with Fluid Temperatures of 150°C to 200°C Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Characteristics of Basin and Range Geothermal Systems with Fluid Temperatures of 150°C to 200°C Abstract Six geothermal reservoirs with fluid temperatures over 200°C and ten geothermal systems with measured fluid temperatures of 150-200°C have been discovered in the northern Basin and Range Province of the USA. A comparison of these high and moderate temperature systems shows considerable overlap in geographical distribution, geology, and physical properties. Our ability to distinguish between moderate and high temperature systems using fluid chemistry has been limited by often

448

Unambiguous Range Extension by Overlay Resolution in Staggered PRT Technique  

Science Conference Proceedings (OSTI)

In this paper a method is presented for separating overlaid echoes in a Doppler weather radar that uses a staggered pulse repetition time (PRT) transmission scheme to mitigate the effects of range–velocity ambiguities. In the standard staggered ...

M. Sachidananda; D. S. Zrnic

2003-05-01T23:59:59.000Z

449

Simulating Range Oversampled Doppler Radar Profiles of Inhomogeneous Targets  

Science Conference Proceedings (OSTI)

A new technique for generating range oversampled profiles of Doppler radar signals that have been backscattered by distributed targets is presented in this paper. The technique was developed for spaceborne cloud radars, but it can just as well be ...

N. A. J. Schutgens

2008-09-01T23:59:59.000Z

450

The range and roots constraints: specifying counting and occurrence problems  

Science Conference Proceedings (OSTI)

We propose a simple declarative language for specifying a wide range of counting and occurrence constraints. This specification language is executable since it immediately provides a polynomial propagation algorithm. To illustrate the capabilities of ...

Christian Bessiere; Emmanuel Hebrard; Brahim Hnich; Zeynep Kiziltan; Toby Walsh

2005-07-01T23:59:59.000Z

451

NNSA Celebrates Earth Week: Pantex 'greens' firing range | National...  

National Nuclear Security Administration (NNSA)

way, and created a program that shows how Pantex goes the extra mile to protect the environment. The project to "green" the firing range had two components encompassing both...

452

Exploration and Development Techniques for Basin and Range Geothermal  

Open Energy Info (EERE)

Techniques for Basin and Range Geothermal Techniques for Basin and Range Geothermal Systems: Examples from Dixie Valley, Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Exploration and Development Techniques for Basin and Range Geothermal Systems: Examples from Dixie Valley, Nevada Abstract Abstract unavailable. Authors David D. Blackwell, Mark Leidig, Richard P. Smith, Stuart D. Johnson and Kenneth W. Wisian Conference GRC Annual Meeting; Reno, NV; 2002/09/22 Published Geothermal Resources Council, 2002 DOI Not Provided Check for DOI availability: http://crossref.org Online Internet link for Exploration and Development Techniques for Basin and Range Geothermal Systems: Examples from Dixie Valley, Nevada Citation David D. Blackwell,Mark Leidig,Richard P. Smith,Stuart D. Johnson,Kenneth

453

Distribution of quaternary rhyolite dome of the Coso Range, California:  

Open Energy Info (EERE)

of quaternary rhyolite dome of the Coso Range, California: of quaternary rhyolite dome of the Coso Range, California: Implications for extent of the geothermal anomaly Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Distribution of quaternary rhyolite dome of the Coso Range, California: Implications for extent of the geothermal anomaly Details Activities (1) Areas (1) Regions (0) Abstract: Thirty-eight separate domes and flows of phenocryst-poor, high-silica rhyolite of similar major element chemical composition were erupted over the past 1 m.y. from vents arranged in a crudely S-shaped array atop a granitic horst in the Coso Range, California. Most of the extrusions are probably less than about 0.3 m.y. old. The area is one of Quaternary basaltic volcanism and crustal extension. The central part of

454

Contemporary Tectonic Deformation of the Basin and Range Province, Western  

Open Energy Info (EERE)

Contemporary Tectonic Deformation of the Basin and Range Province, Western Contemporary Tectonic Deformation of the Basin and Range Province, Western United States: 10 Years of Observation with the Global Positioning System Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Contemporary Tectonic Deformation of the Basin and Range Province, Western United States: 10 Years of Observation with the Global Positioning System Abstract [1] We have estimated patterns and rates of crustal movement across 800 km of the Basin and Range at ∼39° north latitude with Global Positioning System surveys in 1992, 1996, 1998, and 2002. The total rate of motion tangent to the small circle around the Pacific-North America pole of rotation is 10.4 ± 1.0 mm/yr, and motion normal to this small circle is 3.9 ± 0.9 mm/yr compared to the east end of our network. On the Colorado

455

Diachroneity of Basin and Range Extension and Yellowstone Hotspot Volcanism  

Open Energy Info (EERE)

Diachroneity of Basin and Range Extension and Yellowstone Hotspot Volcanism Diachroneity of Basin and Range Extension and Yellowstone Hotspot Volcanism in Northwestern Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Diachroneity of Basin and Range Extension and Yellowstone Hotspot Volcanism in Northwestern Nevada Abstract Some of the earliest volcanic rocks attributed to the Yellowstone hotspot erupted from the McDermitt caldera and related volcanic centers in northwestern Nevada at 17-15 Ma. At that time, extensional faulting was ongoing to the south in central Nevada, leading some to suggest that the nascent hotspot caused or facilitated middle Miocene Basin and Range extension. Regional geologic relationships indicate that the total magnitude of extension in northwestern Nevada is low compared to the amount

456

Hydrothermal Heat Discharge In The Cascade Range, Northwestern United  

Open Energy Info (EERE)

Page Page Edit History Facebook icon Twitter icon » Hydrothermal Heat Discharge In The Cascade Range, Northwestern United States Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Hydrothermal Heat Discharge In The Cascade Range, Northwestern United States Details Activities (3) Areas (1) Regions (0) Abstract: Hydrothermal heat discharge in the Cascade Range includes the heat discharged by thermal springs, by "slightly thermal" springs that are only a few degrees warmer than ambient temperature, and by fumaroles. Thermal-spring heat discharge is calculated on the basis of chloride-flux measurements and geothermometer temperatures and totals ~ 240 MW in the U.S. part of the Cascade Range, excluding the transient post-1980 discharge

457

Reconnaissance electrical surveys in the Coso Range, California | Open  

Open Energy Info (EERE)

electrical surveys in the Coso Range, California electrical surveys in the Coso Range, California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Reconnaissance electrical surveys in the Coso Range, California Details Activities (3) Areas (1) Regions (0) Abstract: Telluric current, audiomagnetotelluric (AMT), and direct current (dc) methods were used to study the electrical structure of the Coso Range and Coso geothermal area. Telluric current mapping outlined major resistivity lows associated with conductive valley fill of the Rose Valley basin, the Coso Basin, and the northern extension of the Coso Basin east of Coso Hot Springs. A secondary resistivity low with a north-south trend runs through the Coso Hot Springs--Devil's Kitchen geothermal area. The secondary low in the geothermal area, best defined by the 7.5-Hz AMT map

458

T-710: Apache HTTP Server Overlapping Ranges Denial of Service  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

10: Apache HTTP Server Overlapping Ranges Denial of Service 10: Apache HTTP Server Overlapping Ranges Denial of Service Vulnerability T-710: Apache HTTP Server Overlapping Ranges Denial of Service Vulnerability September 6, 2011 - 3:09am Addthis PROBLEM: Apache HTTP Server contains a vulnerability that could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. PLATFORM: Apache HTTP Server versions 2.2.19 and prior ABSTRACT: Apache HTTP Server Overlapping Ranges Denial of Service Vulnerability. reference LINKS: FreeBSD VuXML Document Advisory ID: cisco-sa-20110830-apache IBM Alert: swg21512087 Red Hat Advisory: RHSA-2011:1245-1 CVE-2011-3192 CVE-2011-3192 (Update2) IMPACT ASSESSMENT: High Discussion: The vulnerability is due to improper processing of certain user-supplied requests by the affected software. An unauthenticated, remote attacker

459

Northern Basin and Range Geothermal Region | Open Energy Information  

Open Energy Info (EERE)

and Range Geothermal Region and Range Geothermal Region Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Northern Basin and Range Geothermal Region Details Areas (34) Power Plants (3) Projects (7) Techniques (33) Map: {{{Name}}} Examination of seismicity and late Quaternary faults in Montana and Idaho north of the Snake River Plain shows a geographic correspondence between high seismicity and 24 faults that have experienced surface rupture during the late Quaternary. The Lewis and Clark Zone delineates the northern boundary of this tectonically active extensional region. Earthquakes greater than magnitude 5.5 and all identified late Quaternary faults are confined to the Montana-Idaho portion of the Basin and Range Province south of the Lewis and Clark Zone. Furthermore, all 12 Holocene faults are

460

Late Cenozoic volcanism, geochronology, and structure of the Coso Range,  

Open Energy Info (EERE)

Late Cenozoic volcanism, geochronology, and structure of the Coso Range, Late Cenozoic volcanism, geochronology, and structure of the Coso Range, Inyo County, California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Late Cenozoic volcanism, geochronology, and structure of the Coso Range, Inyo County, California Details Activities (1) Areas (1) Regions (0) Abstract: The Coso Range lies at the west edge of the Great Basin, adjacent to the southern part of the Sierra Nevada. A basement complex of pre-Cenozoic plutonic and metamorphic rocks is partly buried by approx.35 km^3 of late Cenozoic volcanic rocks that were erupted during two periods, as defined by K-Ar dating: (1) 4.0--2.5 m.y., approx.31 km^3 of basalt, rhyodacite, dacite, andesite, and rhyolite, in descending order of abundance, and (2) < or =1.1 m.y., nearly equal amounts of basalt and

Note: This page contains sample records for the topic "rangely weber sand" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Geothermal Resource Analysis And Structure Of Basin And Range Systems,  

Open Energy Info (EERE)

Analysis And Structure Of Basin And Range Systems, Analysis And Structure Of Basin And Range Systems, Especially Dixie Valley Geothermal Field, Nevada Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report: Geothermal Resource Analysis And Structure Of Basin And Range Systems, Especially Dixie Valley Geothermal Field, Nevada Details Activities (12) Areas (5) Regions (0) Abstract: Publish new thermal and drill data from the Dizie Valley Geothermal Field that affect evaluation of Basin and Range Geothermal Resources in a very major and positive way. Completed new geophysical surveys of Dizie Valley including gravity and aeromagnetics and integrated the geophysical, seismic, geological and drilling data at Dizie Valley into local and regional geologic models. Developed natural state mass and energy

462

Developments in Operational Long-Range Climate Prediction at CPC  

Science Conference Proceedings (OSTI)

The science, production methods, and format of long-range forecasts (LRFs) at the Climate Prediction Center (CPC), a part of the National Weather Service’s (NWS’s) National Centers for Environmental Prediction (NCEP), have evolved greatly since ...

Edward A. O’Lenic; David A. Unger; Michael S. Halpert; Kenneth S. Pelman

2008-06-01T23:59:59.000Z

463

Spatiotemporal Behavior of the TIGGE Medium-Range Ensemble Forecasts  

Science Conference Proceedings (OSTI)

Using the recently developed mean–variance of logarithms (MVL) diagram, together with The Observing System Research and Predictability Experiment (THORPEX) Interactive Grand Global Ensemble (TIGGE) archive of medium-range ensemble forecasts from ...

Zak Kipling; Cristina Primo; Andrew Charlton-Perez

2011-08-01T23:59:59.000Z

464

Adaptive Support of Range Queries via Push-Pull Algorithms  

Science Conference Proceedings (OSTI)

In many real time interactive simulations the problem of interest management is that of filtering updates through application-specified range queries. This "associative' form of memory access is often implemented more simply as a reference memory access ...

Rob Minson; Georgios Theodoropoulos

2007-06-01T23:59:59.000Z

465

A low-power-extended-linear-range magnetic levitator  

E-Print Network (OSTI)

In this thesis, I designed and built analog circuits to extend the linear range of a magnetic levitator. Analog Devices AD633 multipliers are used to implement nonlinear terms which compensate for the electromagnet and ...

Johnson, Rayal St. Patrick

2007-01-01T23:59:59.000Z

466

Interim report on long range plan for nuclear physics  

SciTech Connect

The interim report on the updated NSAC Long Range Plan for Nuclear Physics will be presented to the community for discussion and comment before submission to the funding agencies. The presentation will be coordinated by E. Moniz chair of NSAC.

1995-04-01T23:59:59.000Z

467

Doppler Sonar and Surface Waves: Range and Resolution  

Science Conference Proceedings (OSTI)

The performance limitations of an acoustic Doppler sonar system are explored and compared with anticipated requirements for the measurement of surface wave directional/frequency spectra. To obtain measurements to a range D requires a delay ?t ...

Jerome A. Smith

1989-08-01T23:59:59.000Z

468

Time–Space Distribution of Long-Range Atmospheric Predictability  

Science Conference Proceedings (OSTI)

The global three-dimensional structure of long-range (one month to one season) atmospheric predictability was investigated with a general circulation model. The main focus was to ascertain the role of atmospheric initial conditions for such ...

Thomas Reichler; John O. Roads

2004-02-01T23:59:59.000Z

469

Seismotectonics of the Coso Range-Indian Wells Valley region...  

Open Energy Info (EERE)

Journal Geological Society of America, 2002 DOI 10.11300-8137-1195-9.277 Online Internet link for Seismotectonics of the Coso Range-Indian Wells Valley region, California:...

470

Dynamical Extended Range Forecasting (DERF) at the National Meteorological Center  

Science Conference Proceedings (OSTI)

Early results are presented of an experimental program in Dynamical Extended Range Forecasting at the National Meteorological Center. The primary objective of this program is to assess the feasibility of extending operational numerical weather ...

M. Steven Tracton; Kingtse Mo; Wilbur Chen; Eugenia Kalnay; Robert Kistler; Glenn White

1989-07-01T23:59:59.000Z

471

The Compact RCS / Antenna Range at MIT Lincoln Laboratory  

E-Print Network (OSTI)

A new compact range with a state-of-the-art instrumentation system was installed at Lincoln Laboratory and is currently in use. This paper describes the chamber with varied-height absorber, the rolled-edge reflector and ...

Shields, Michael W.

472

Ranges of Atmospheric Mass and Composition of Super Earth Exoplanets  

E-Print Network (OSTI)

Terrestrial-like exoplanets may obtain atmospheres from three primary sources: Capture of nebular gases, degassing during accretion, and degassing from subsequent tectonic activity. Here we model degassing during accretion to estimate the range of atmospheric mass and composition on exoplanets ranging from 1 to 30 Earth masses. We use bulk compositions drawn from primitive and differentiated meteorite compositions. Degassing alone can create a wide range of masses of planetary atmospheres, ranging from less than a percent of the planet's total mass up to ~6 mass% of hydrogen, ~20 mass% of water, and/or ~5 mass% of carbon compounds. Hydrogen-rich atmospheres can be outgassed as a result of oxidizing metallic iron with water, and excess water and carbon can produce atmospheres through simple degassing. As a byproduct of our atmospheric outgassing models we find that modest initial water contents (10 mass% of the planet and above) create planets with deep surface liquid water oceans soon after accretion is complete.

L. Elkins-Tanton; S. Seager

2008-08-13T23:59:59.000Z

473

VEE-0075- In the Matter of Viking Range Corporation  

Energy.gov (U.S. Department of Energy (DOE))

This Decision and Order considers an Application for Exception filed by Viking Range Corporation (Viking) seeking exception relief from the provisions of 10 C.F.R. Part 430, Energy Conservation...

474

Diachroneity of Basin and Range Extension and Yellowstone Hotspot...  

Open Energy Info (EERE)

km of slip along a west-dipping normal fault on the west side of the range. Apatite fission-track data from the Santa Rosa footwall block indicate that faulting and extension...