Sample records for ra ac ct

  1. 225-Ac and 223-Ra Production via 800 MeV Proton Irradiation of Natural Thorium Target

    E-Print Network [OSTI]

    J. W. Weidner; S. G. Mashnik; K. D. John; B. Ballard; E. R. Birnbaum; L. J. Bitteker; A. Couture; M. E. Fassbender; G. S. Goff; R. Gritzo; F. M. Hemez; W. Runde; J. L. Ullmann; L. E. Wolfsberg; F. M. Nortier

    2012-04-10T23:59:59.000Z

    Cross sections for the formation of 225,227-Ac, 223,225-Ra, and 227-Th via the proton bombardment of natural thorium targets were measured at a nominal proton energy of 800 MeV. No earlier experimental cross section data for the production of 223,225-Ra, 227-Ac and 227-Th by this method were found in the literature. A comparison of theoretical predictions with the experimental data shows agreement within a factor of two. Results indicate that accelerator-based production of 225-Ac and 223-Ra is a viable production method.

  2. Proton-induced cross sections relevant to production of 225Ac and 223Ra in natural thorium targets below 200 MeV

    E-Print Network [OSTI]

    J. W. Weidner; S. G. Mashnik; K. D. John; F. Hemez; B. Ballard; H. Bach; E. R. Birnbaum; L. J. Bitteker; A. Couture; D. Dry; M. E. Fassbender; M. S. Gulley; K. R. Jackman; J. L. Ullmann; L. E. Wolfsberg; F. M. Nortier

    2012-05-15T23:59:59.000Z

    Cross sections for 223,225Ra, 225Ac and 227Th production by the proton bombardment of natural thorium targets were measured at proton energies below 200 MeV. Our measurements are in good agreement with previously published data and offer a complete excitation function for 223,225Ra in the energy range above 90 MeV. Comparison of theoretical predictions with the experimental data shows reasonable-to-good agreement. Results indicate that accelerator-based production of 225Ac and 223Ra below 200 MeV is a viable production method.

  3. Co.ra

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp -KWatertowni5W 95.5x-L* d! CT NC0ICo.ra

  4. Molecular imaging in oncology: the acceptance of PET/CT and the emergence of MR/PET imaging

    E-Print Network [OSTI]

    Schiepers, Christiaan; Dahlbom, Magnus

    2011-01-01T23:59:59.000Z

    CT—Computed tomography . PET—Positron Emission Tomography .body imaging with MRI or PET/CT: the future for single-Sollitto RA et al (2009) 18F-FDG PET/CT of transitional cell

  5. RAPID METHOD FOR DETERMINATION OF {sup 228}Ra IN WATER SAMPLES

    SciTech Connect (OSTI)

    Maxwell, S.

    2012-09-05T23:59:59.000Z

    A new rapid method for the determination of {sup 228}Ra in natural water samples has been developed at the SRNL/EBL (Savannah River National Lab/ Environmental Bioassay Laboratory) that can be used for emergency response or routine samples. While gamma spectrometry can be employed with sufficient detection limits to determine {sup 228}Ra in solid samples (via {sup 228}Ac) , radiochemical methods that employ gas flow proportional counting techniques typically provide lower MDA (Minimal Detectable Activity) levels for the determination of {sup 228}Ra in water samples. Most radiochemical methods for {sup 228}Ra collect and purify {sup 228}Ra and allow for {sup 228}Ac daughter ingrowth for ~36 hours. In this new SRNL/EBL approach, {sup 228}Ac is collected and purified from the water sample without waiting to eliminate this delay. The sample preparation requires only about 4 hours so that {sup 228}Ra assay results on water samples can be achieved in < 6 hours. The method uses a rapid calcium carbonate precipitation enhanced with a small amount of phosphate added to enhance chemical yields (typically >90%), followed by rapid cation exchange removal of calcium. Lead, bismuth, uranium, thorium and protactinium isotopes are also removed by the cation exchange separation. {sup 228}Ac is eluted from the cation resin directly onto a DGA Resin cartridge attached to the bottom of the cation column to purify {sup 228}Ac. DGA Resin also removes lead and bismuth isotopes, along with Sr isotopes and {sup 90}Y. La is used to determine {sup 228}Ac chemical yield via ICP-MS, but {sup 133}Ba can also be used instead if ICP-MS assay is not available. Unlike some older methods, no lead or strontium holdback carriers or continual readjustment of sample pH is required.

  6. RAPID DETERMINATION OF RA-226 IN ENVIRONMENTAL SAMPLES

    SciTech Connect (OSTI)

    Maxwell, S.

    2012-01-03T23:59:59.000Z

    A new rapid method for the determination of {sup 226}Ra in environmental samples has been developed at the Savannah River Site Environmental Lab (Aiken, SC, USA) that can be used for emergency response or routine sample analyses. The need for rapid analyses in the event of a Radiological Dispersive Device or Improvised Nuclear Device event is well-known. In addition, the recent accident at Fukushima Nuclear Power Plant in March, 2011 reinforces the need to have rapid analyses for radionuclides in environmental samples in the event of a nuclear accident. {sup 226}Ra (T1/2 = 1,620 years) is one of the most toxic of the long-lived alpha-emitters present in the environment due to its long life and its tendency to concentrate in bones, which increases the internal radiation dose of individuals. The new method to determine {sup 226}Ra in environmental samples utilizes a rapid sodium hydroxide fusion method for solid samples, calcium carbonate precipitation to preconcentrate Ra, and rapid column separation steps to remove interferences. The column separation process uses cation exchange resin to remove large amounts of calcium, Sr Resin to remove barium and Ln Resin as a final purification step to remove {sup 225}Ac and potential interferences. The purified {sup 226}Ra sample test sources are prepared using barium sulfate microprecipitation in the presence of isopropanol for counting by alpha spectrometry. The method showed good chemical recoveries and effective removal of interferences. The determination of {sup 226}Ra in environmental samples can be performed in less than 16 h for vegetation, concrete, brick, soil, and air filter samples with excellent quality for emergency or routine analyses. The sample preparation work takes less than 6 h. {sup 225}Ra (T1/2 = 14.9 day) tracer is used and the {sup 225}Ra progeny {sup 217}At is used to determine chemical yield via alpha spectrometry. The rapid fusion technique is a rugged sample digestion method that ensures that any refractory radium particles are effectively digested. The preconcentration and column separation steps can also be applied to aqueous samples with good results.

  7. RA

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:AdministrationAnalysis andBHoneywell9/%2A en International Nuclear

  8. eRA Training Team1 Terminations

    E-Print Network [OSTI]

    Baker, Chris I.

    eRA Training Team1 xTrain Terminations Electronic Research Administration Sponsored by: The National Institutions of Health, Office of Extramural Research April 2010 #12;eRA Training Team2 xTrain General Information xTrain Overview The following section provides general information on the xTrain

  9. eRA Training Team1 Terminations

    E-Print Network [OSTI]

    Baker, Chris I.

    eRA Training Team1 xTrain Terminations Electronic Research Administration Sponsored by: The National Institutes of Health, Office of Extramural Research March 2012 #12;eRA Training Team2 xTrain General Information xTrain Overview The following section provides general information on the xTrain

  10. Ra-226 radioassay of soil and tailings

    SciTech Connect (OSTI)

    Sabau, C.S.; Rayno, D.R.; Kretz, N.D.; Zelle, P.W.

    1983-01-01T23:59:59.000Z

    Studies of inactive uranium tailings piles have shown that tailings sands containing Ra-226 and other radionuclides may be dispersed by wind and water erosion, causing contamination of adjacent areas. To conduct an effective cleanup operation, it is necessary that boundaries of contamination be well defined. To accomplish this, data from surface gamma-ray surveys made under the Measurement Monitoring Program of the US DOE's Uranium Mill Tailings Remedial Action Project (UMTRAP) are first used to delineate a general outline of the contaminated area. Then, data from portable scintillometer surveys and from sealed-can gamma-ray analyses of soil samples are used to more precisely define the perimeter of Ra-226 contamination. These field measurements are supported by radiochemical analyses of randomly selected samples. Because of its adaptability to the widely varying chemical composition of the material in these samples, the complexing agent EDTA is used in a complexometric leaching procedure to analyze Ra-226. By this procedure, natural concentrations of Ra-226 in soil (approx. 1 pCi/g) can be measured routinely. The potential limit of detection is in the 0.1 to 0.5 pCi/g range. Details of the method, which includes leaching of radium followed by radon de-emanation, are described. Comparative data for various soil and tailings samples are presented.

  11. english 31AC african-amercan studies 17AC history 7B public health 130AC sociology 3AC education 30AC ethnic studies 135AC geography 150AC history 127AC information 142AC psychology 125AC anthropology 2AC american

    E-Print Network [OSTI]

    Alvarez-Cohen, Lisa

    · anthropology 2AC · american studies 10AC · gender and womens studies 50AC · music 26AC · spanish 135AC 50AC · music 26AC · spanish 135AC · sociology 190AC · public policy 117AC · peace and conflict studies 10AC · gender and womens studies 50AC · music 26AC · spanish 135AC · sociology 190AC · public

  12. NETL CT Imaging Facility

    ScienceCinema (OSTI)

    None

    2014-05-21T23:59:59.000Z

    NETL's CT Scanner laboratory is equipped with three CT scanners and a mobile core logging unit that work together to provide characteristic geologic and geophysical information at different scales, non-destructively.

  13. NETL CT Imaging Facility

    SciTech Connect (OSTI)

    None

    2013-09-04T23:59:59.000Z

    NETL's CT Scanner laboratory is equipped with three CT scanners and a mobile core logging unit that work together to provide characteristic geologic and geophysical information at different scales, non-destructively.

  14. R.A. Spicer -Publications. January, 2010 1 R.A. Spicer Publications -Articles, Papers and Books

    E-Print Network [OSTI]

    Spicer, Robert A

    2 108. Spicer, R.A., Ahlberg, A., Herman, A.B., Hofmann, C-C., Raikevich, M., Valdes, P -de Leon, M.P., Spicer, R.A., and Steart, D.C., In Press. Climatic reconstruction of two Pliocene Yakutia). Palaeogeography, Palaeoclimatolgy, Palaeoecology, 111. Moiseeva, M.G., Herman, A.B., and Spicer

  15. Name Email address Telephone no: Professor Edwin van Beek (Director, CRIC/ SINAPSE, edwin-vanbeek@ed.ac.uk 0131 242 7760

    E-Print Network [OSTI]

    Swain, Peter

    .lilburn@ed.ac.uk 0131 242 7757 Dr Gill MacNaught (MRI Physicist) gillian.macnaught@ed.ac.uk 0131 242 9168 PET-CT / CT Dr.cooper@luht.scot.nhs.uk 0131 242 7770 Danielle Richardson (CT/MRI/PET) danielle.bertram@luht.scot.nhs.uk 0131 242 7753/70/80 Barbara Allen (CT/MRI/PET) barbara.allen@nhslothian.scot.nhs.uk 0131 242 7753/70/80 Suzanne McKendry (CT/MRI/PET

  16. Medical Imaging Computed Tomography (CT)

    E-Print Network [OSTI]

    Massey, Thomas N.

    Module 10 Medical Imaging · X-rays · Computed Tomography (CT) · Positron Emission Tomography (PET Sources PET-TOF #12;Four Sources PET #12;Four Sources PET-TOF #12;PET Scan MRI CT scan #12;Endocrine Gland,000 pixels! #12;Modern Example of CT Scan with the addition of Surface Shading Standard CT With Surface

  17. CT Solar Loan

    Broader source: Energy.gov [DOE]

    The Clean Energy Finance and Investment Authority is offering a pilot loan program, CT Solar Loan, to provide homeowners with 15-year loans for solar PV equipment. The loans are administered...

  18. Simulation of Heat Treatment Distortion R.A. Hardin1

    E-Print Network [OSTI]

    Beckermann, Christoph

    quenched in water and in oil. Unfortunately, due to the lack of documentation on the heat treatment process a test piece casting to be produced at a participating foundry to provide data on heat treatmentSimulation of Heat Treatment Distortion R.A. Hardin1 and C. Beckermann2 1 Research Engineer, 2

  19. NEWS & VIEWS X-RaY oPtiCS

    E-Print Network [OSTI]

    Loss, Daniel

    NEWS & VIEWS X-RaY oPtiCS Clarity through a keyhole Janos Hajdu1,2 & Filipe R. n. C. maia2 are at 1 Stanford Synchrotron Radiation Laboratory, Stanford Linear Accelerator Center, 2575 Sand Hill Road, Menlo, as it does in conventional crystallography, but only on the wavelength used, the extent of ionization damage

  20. 3.3.3AC Sweep AC . AC

    E-Print Network [OSTI]

    ­. DC ­ AC ­) .( . ­ ,, '­Spice .Spice . : 0 0 E1 PWR(V(%IN+, %IN . )2.3( Etable " . . : 00 V1 0Vdc E2 Pwr(V(%IN+, %IN-),2) ETABLE TABLE = (5

  1. Performance & Risk Assessment Community of Practice (P&RA CoP...

    Broader source: Energy.gov (indexed) [DOE]

    P&RA CoP's Technical Exchange Meeting held on December 11-12, 2014 in Las Vegas, NV P&RA CoP's Technical Exchange Meeting held on December 11-12, 2014 in Las Vegas, NV P&RA CoP's...

  2. Octupole collectivity in $^{220}$Rn and $^{224}$Ra

    E-Print Network [OSTI]

    Gaffney, Liam Paul

    Collective properties of the radioactive nuclei $^{220}$Rn and $^{224}$Ra have been studied via Coulomb excitation of a $2.8$~A.MeV radioactive ion beam (RIB) incident upon $^{60}$Ni, $^{112,114}$Cd and $^{120}$Sn targets. The experiments took place at the REX-ISOLDE RIB facility, CERN. De-excitation $gamma$-ray yields following multiple-step Coulomb excitation were detected in coincidence with recoiling target nuclei in the Miniball spectrometer. For the first time, $B(E3;3^{+} ightarrow0^{+})$ values have been directly measured with a radioactive ion beam. In the process, $^{224}$Ra becomes the heaviest post-accelerated RIB to date at ISOLDE (with the possible exception of the quasi-stable $^{238}$U). The measurements presented in this thesis represent a tripling of the number of nuclei around $Zsimeq88$ and $Nsimeq134$, for which direct measurements of the octupole collectivity have been performed. The only previous measurements being for the relatively long-lived $^{226}$Ra. The $gamma$-ray yields, in con...

  3. Bremsstrahlung emission during $?$-decay of $^{226}{\\rm Ra}$

    E-Print Network [OSTI]

    Giorgio Giardina; Giovanni Fazio; Giuseppe Mandaglio; Marina Manganaro; Serghei P. Maydanyuk; Vladislav S. Olkhovsky; Nikolay V. Eremin; Anton A. Paskhalov; Dmitry A. Smirnov; Carmelo Sacca

    2008-04-16T23:59:59.000Z

    We obtained the spectrum of probability of the bremsstrahlung emission accompanying the $\\alpha$-decay of $^{226}{\\rm Ra}$ (E$_{\\alpha}$=4.8 MeV) by measuring the $\\alpha$-$\\gamma$ coincidences and using the model presented in our previous study on the $\\alpha-$decay of $^{214}{\\rm Po}$ (E$_{\\alpha}$=7.7 MeV). We compare the experimental data with the quantum mechanical calculation and find a good agreement between theory and experiment. We discuss the differences between the photon spectra connected with the $\\alpha$-decay of the $^{226}{\\rm Ra}$ and $^{214}{\\rm Po}$ nuclei. For the two mentioned nuclei we analyze the bremsstrahlung emission contributions from the tunneling and external regions of the nucleus barrier into the total spectrum, and we find the destructive interference between these contributions. We also find that the emission of photons during tunneling of the $\\alpha$-particle gives an important contribution to the bremsstrahlung spectrum in the whole E$_{\\gamma}$ energy range of the studied $^{226}$Ra nucleus.

  4. Ra Solar Systems Solutions SL | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere I GeothermalPotentialBiopowerSolidGenerationMethodInformationeNevada <RECServices,RYPOS Inc Jump to:Ra

  5. CT NC0

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp -KWatertowni5W 95.5x-L* d! CT NC0 - i , ,.

  6. The Bayo Canyon/radioactive lanthanum (RaLa) program

    SciTech Connect (OSTI)

    Dummer, J.E.; Taschner, J.C.; Courtright, C.C.

    1996-04-01T23:59:59.000Z

    LANL conducted 254 radioactive lanthanum (RaLa) implosion experiments Sept. 1944-March 1962, in order to test implosion designs for nuclear weapons. High explosives surrounding common metals (surrogates for Pu) and a radioactive source containing up to several thousand curies of La, were involved in each experiment. The resulting cloud was deposited as fallout, often to distances of several miles. This report was prepared to summarize existing records as an aid in evaluating the off-site impact, if any, of this 18-year program. The report provides a historical setting for the program, which was conducted in Technical Area 10, Bayo Canyon about 3 miles east of Los Alamos. A description of the site is followed by a discussion of collateral experiments conducted in 1950 by US Air Force for developing an airborne detector for tracking atmospheric nuclear weapons tests. All known off-site data from the RaLa program are tabulated and discussed. Besides the radiolanthanum, other potential trace radioactive material that may have been present in the fallout is discussed and amounts estimated. Off-site safety considerations are discussed; a preliminary off-site dose assessment is made. Bibliographical data on 33 persons important to the program are presented as footnotes.

  7. A correlation between soil descriptions and {sup 226}Ra concentrations in Florida soils

    SciTech Connect (OSTI)

    Harrison, D.P.

    1992-12-31T23:59:59.000Z

    The soil radium content in Florida is highly variable. The range in radium concentrations, where the samples involved in this study are concerned, is from 0.1 pCi/g to 18.5 pCi/g. Low {sup 226}Ra concentrations (0.1 to 5 pCi/g) are evidenced in sands, moderate concentrations (5 to 11 pCi/g) are found in silt and gravel, and high {sup 226}Ra concentrations (>11 pCi/g) are found in soil horizons with shell, clay, and strata with phosphate. Strata containing phosphate yields a high concentration of {sup 226}Ra. The information obtained in this study, soil descriptions with their corresponding {sup 226}Ra concentrations, comes from geological cores drilled by geotechnical consultants with gamma spectrometry analysis performed by high resolution gamma spectroscopy. Concentration; of {sup 226}Ra generally increase with depth. These cores are usually terminated at 20 feet deep, with some cores being shallower than this due to hitting bedrock or encountering the water table. These frequency distributions give the core-logging geologist an approximate concentration of {sup 226}Ra based on the description of the soil. Since the correlation of {sup 226}Ra and soil descriptions can be used as a tool in assigning indoor radon potential, this study is of importance to land managers, contractors, developers, and regulating agencies who are attempting to place standards on tracts of land with {sup 226}Ra concentration used as a criterion.

  8. Design and analysis of modern three-phase AC/AC power converters for AC drives and utility interface 

    E-Print Network [OSTI]

    Kwak, Sangshin

    2005-08-29T23:59:59.000Z

    Significant advances in modern ac/ac power converter technologies and demands of industries have reached beyond standard ac/ac power converters with voltage-source inverters fed from diode rectifiers. Power electronics converters have been matured...

  9. DOE - Office of Legacy Management -- Seymour CT Site - CT 02

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp -K Le BlondSanta SusanaSeymour CT Site - CT

  10. Comparison of CT, PET, and PET/CT for Staging of Patients with Indolent Non-Hodgkin’s Lymphoma

    E-Print Network [OSTI]

    Fueger, Barbara J.; Yeom, Kristen; Czernin, Johannes; Sayre, James W.; Phelps, Michael E.; Allen-Auerbach, Martin S.

    2009-01-01T23:59:59.000Z

    Differences between PET and CT were not significant forperformed significantly better than PET and CT in correctlyadditional information over PET and CT for the staging and

  11. PoPulation Differentiation anD raPiD evolution of egg Color in aCCorDanCe with Solar raDiation

    E-Print Network [OSTI]

    Lahti, David C.

    PoPulation Differentiation anD raPiD evolution of egg Color in aCCorDanCe with Solar raDiation Davi, . Diferenciación entre Poblaciones y Evolución Rápida del Color de los Huevos de Acuerdo a la Radiación Solar Uy C P' R d Pm wb, ://www.j. m/I.. DOI: 10.1525/k.2008.07033DOI: 10.1525/k.2008.07033 Bird egg color

  12. Limited View Angle Iterative CT Reconstruction

    E-Print Network [OSTI]

    . Connelly, "CT Technologies," in Aspects of Explosives Detection, Elsevier 2009. Dual energy CT Z. Ying, R. Nam and C. R. Crawford, "Dual energy computed tomography for explosive detection," Journal of X

  13. Audit Report: OAS-RA-12-12 | Department of Energy

    Energy Savers [EERE]

    Audit Report: OAS-RA-12-12 May 22, 2012 The Department of Energy's Clean Cities Alternative Fuel Vehicle Grant Program Funded under the American Recovery and Reinvestment Act...

  14. Ra, a naturally occurring isotope of the 238 U-series with a

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    for counting, liquid scintillation, or mass spectrometry at comparable activities, the simple setup, low cost- fiber and is continuously transferred to a scintillation cham- 226 Ra determination via the rate of 222

  15. First In Vivo Evaluation of Liposome-encapsulated 223Ra as a Potential Alpha-particle-emitting Cancer Therapeutic Agent

    SciTech Connect (OSTI)

    Jonasdottir, Thora J.; Fisher, Darrell R.; Borrebaek, Jorgen; Bruland, Oyvind S.; Larsen, Roy H.

    2006-09-13T23:59:59.000Z

    Liposomes carrying chemotherapeutics have had some success in cancer treatment and may be suitable carriers for therapeutic radionuclides. This study was designed to evaluate the biodistribution of and to estimate the radiation doses from the alpha emitter 223Ra loaded into pegylated liposomes in selected tissues. 223Ra was encapsulated in pegylated liposomal doxorubicin by ionophore-mediated loading. The biodistribution of liposomal 223Ra was compared to free cationic 223Ra in Balb/C mice. We showed that liposomal 223 Ra circulated in the blood with an initial half-time in excess of 24 hours, which agreed well with that reported for liposomal doxorubicin in rodents, while the blood half-time of cationic 223Ra was considerably less than one hour. When liposomal 223 Ra was catabolized, the released 223Ra was either excreted or taken up in the skeleton. This skeletal uptake increased up to 14 days after treatment, but did not reach the level seen with free 223Ra. Pre-treatment with non-radioactive liposomal doxorubicin 4 days in advance lessened the liver uptake of liposomal 223 Ra. Dose estimates showed that the spleen, followed by bone surfaces, received the highest absorbed doses. Liposomal 223 Ra was relatively stable in vivo and may have potential for radionuclide therapy and combination therapy with chemotherapeutic agents.

  16. Ac-Ac Dual Active Bridge Converter for Solid State Transformer

    E-Print Network [OSTI]

    Kimball, Jonathan W.

    flow. The advantages of direct ac-ac conversion include fewer power conversion stages and minimized single-stage direct ac-ac power conversion to an SST. Fewer conversion stages reduce conduction loss) converter in direct ac-ac power conversion. Like a DAB converter as dc-dc power supply in [5] and [6

  17. AC and DC power transmission

    SciTech Connect (OSTI)

    Not Available

    1985-01-01T23:59:59.000Z

    The technical and economic assessment of AC and DC transmission systems; long distance transmission, cable transmission, system inter-connection, voltage support, reactive compensation, stabilisation of systems; parallel operation of DC links with AC systems; comparison between alternatives for particular schemes. Design and application equipment: design, testing and application of equipment for HVDC, series and shunt static compensated AC schemes, including associated controls. Installations: overall design of stations and conductor arrangements for HVDC, series and shunt static AC schemes including insulation co-ordination. System analysis and modelling.

  18. PII S0016-7037(00)00369-0 Ra isotopes and Rn in brines and ground waters of the Jordan-Dead Sea Rift Valley

    E-Print Network [OSTI]

    Yehoshua, Kolodny

    PII S0016-7037(00)00369-0 Ra isotopes and Rn in brines and ground waters of the Jordan-Dead Sea Valley waters being mixtures of fresh water with saline brines. Ra is efficiently extracted from surrounding rocks into the brine end member. 228 Ra/226 Ra ratios are exceptionally low 0.07 to 0.9, mostly

  19. ACS | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to:Ezfeedflag JumpID-fTriWildcat 1 WindtheEnergySulfonate as aAAB AsiaABEEolicaSection Logo:ACS

  20. ACS Symposium Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del(ANL-IN-03-032)8Li (59AJ76) (See the EnergyTAMANG, APIL. A Multilevel224th ACS

  1. On-line Excited-State Laser Spectroscopy of Trapped Short-Lived Ra$^+$ Ions

    E-Print Network [OSTI]

    O. O. Versolato; G. S. Giri; L. W. Wansbeek; J. E. van den Berg; D. J. van der Hoek; K. Jungmann; W. L. Kruithof; C. J. G. Onderwater; B. K. Sahoo; B. Santra; P. D. Shidling; R. G. E. Timmermans; L. Willmann; H. W. Wilschut

    2010-03-29T23:59:59.000Z

    As an important step towards an atomic parity violation experiment in one single trapped Ra$^+$ ion, laser spectroscopy experiments were performed with on-line produced short-lived $^{212,213,214}$Ra$^+$ ions. The isotope shift of the $6\\,^2$D$_{3/2}$\\,-\\,$7\\,^2$P$_{1/2}$ and $6\\,^2$D$_{3/2}$\\,-\\,$7\\,^2$P$_{3/2}$ transitions and the hyperfine structure constant of the $7\\,^2$S$_{1/2}$ and $6\\,^2$D$_{3/2}$ states in $^{213}$Ra$^+$ were measured. These values provide a benchmark for the required atomic theory. A lower limit of $232(4)$ ms for the lifetime of the metastable $6\\,^2$D$_{5/2}$ state was measured by optical shelving.

  2. AC Resistance measuring instrument

    DOE Patents [OSTI]

    Hof, Peter J. (Richland, WA)

    1983-01-01T23:59:59.000Z

    An auto-ranging AC resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an AC excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance. After the auto-ranging and auto-compensation functions are complete, the microprocessor calculates the resistance of the load from the selected range resistance, the excitation signal, and the load voltage signal, and displays of the measured resistance on a digital display of the instrument.

  3. AC resistance measuring instrument

    DOE Patents [OSTI]

    Hof, P.J.

    1983-10-04T23:59:59.000Z

    An auto-ranging AC resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an AC excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance. After the auto-ranging and auto-compensation functions are complete, the microprocessor calculates the resistance of the load from the selected range resistance, the excitation signal, and the load voltage signal, and displays of the measured resistance on a digital display of the instrument. 8 figs.

  4. "EMM Region","PC","IGCC","PC","Conv. CT","Adv. CT","Conv. CC...

    U.S. Energy Information Administration (EIA) Indexed Site

    "EMM Region","PC","IGCC","PC","Conv. CT","Adv. CT","Conv. CC","Adv. CC","Adv. CC wCCS","Fuel Cell","Nuclear","Biomass","MSW","On-shore Wind","Off-shore Wind","Solar...

  5. Audit Report: OAS-RA-11-08 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03 Audit Report:OAS-RA-11-02RA-11-08

  6. CT Offshore | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2,AUDIT REPORT Americium/CuriumAguaBBBWind-BrizaHKC WindCT Offshore Place:

  7. Supply of purified Th228 for Ra224 generators. Final CRADA Report .

    SciTech Connect (OSTI)

    Ehst, D. A.; Nuclear Engineering Division

    2009-10-02T23:59:59.000Z

    CRADA was terminated when it was determined that the Russians could not perform the terms of the subcontract. It became apparent that the Russians would not be a reliable source of Th228, as a precursor in the decay chain which leads to Ra224. Their government policies will prohibit the export of Th228 in quantities needed for commercial cancer therapy.

  8. George Feher (Photograph by R.A. Icaacson) Photosynthesis Research 55: 140, 1998.

    E-Print Network [OSTI]

    Govindjee "Gov"

    George Feher (Photograph by R.A. Icaacson) #12;Photosynthesis Research 55: 1­40, 1998. © 1998 of research in bacterial photosynthesis and the road leading to it: A personal account George Feher In this minireview I present a very personal account of my life and research in bacterial photosynthesis

  9. August 2006 Grantee Registration Process in NIH eRA Commons

    E-Print Network [OSTI]

    Baker, Chris I.

    August 2006 Grantee Registration Process in NIH eRA Commons Detailed Steps STEP 1. Begin Grantee Registration Steps 1 #12;August 2006 · It may include numbers · It must contain letters · It may. 2. In the User ID box, type the user name you created for your Commons account. Grantee Registration

  10. RA After Hours On Call (971) 246-1388 Your Guide to

    E-Print Network [OSTI]

    Latiolais, M. Paul

    for the resident to pick up at the move-in station. Laundry Laundry facilities are located on odd-numbered floors is on for an extended amount of time, please notify the Help desk or the RA on call. If you leave trash, abandoned

  11. Siemens AG, CT, September 2001 CORPORATETECHNOLOGY

    E-Print Network [OSTI]

    s © Siemens AG, CT, September 2001 CORPORATETECHNOLOGY Research and Technology at Siemens Transportation Power Information & Communications Health Automation & Control #12;2© Siemens AGResearch and Technology at Siemens CORPORATETECHNOLOGY CT / E 020 a - 02.01 Key Figures for 2000 Amounts in billions

  12. lated to attempts to induce RA in the ru-men in vitro and in vivo, and understand-

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    in vitro increased acetate production through RA. Such ex- periments in vivo are excluded however because introduction of frozen and thawed cattle hindgut contents to a sheep rumen did not affect rumen fermentation stoi- chiometry in vitro [5]. RA is a major characteristic of the cae- cal fermentation in young

  13. (81), ra39. [DOI: 10.1126/scisignal.2000316]2Science Signaling Pawson and Rune Linding (28 July 2009)

    E-Print Network [OSTI]

    (81), ra39. [DOI: 10.1126/scisignal.2000316]2Science Signaling Pawson and Rune Linding (28 July,5,6,7 Tony Pawson,1,2 Rune Linding8 (Published 28 July 2009; Volume 2 Issue 81 ra39) Protein kinases enable

  14. RaPID: THE END OF HEURISTIC PID TUNING Peter Van Overschee, Christiaan Moons, Wim Van Brempt

    E-Print Network [OSTI]

    RaPID: THE END OF HEURISTIC PID TUNING Peter Van Overschee, Christiaan Moons, Wim Van Brempt Paul Vanvuchelen, Bart De Moor Abstract: RaPID (Robust Advanced PID Control) is a new and original engineer- ing tool for the design and implementation of optimal PID controllers. It integrates data acquisition

  15. AVTA: Aerovironment AC Level 2 Charging System Testing Results...

    Broader source: Energy.gov (indexed) [DOE]

    Aerovironment AC Level 2 - February 2012 More Documents & Publications AVTA: Clipper Creek AC Level 2 Charging System Testing Results AVTA: Eaton AC Level 2 Charging System...

  16. Targeting of Osseous Sites with Alpha-emitting Ra-223: Comparison with the Beta-emitter Sr-89 in Mice

    SciTech Connect (OSTI)

    Henriksen, Gjermund; Fisher, Darrell R.; Roeske, John C.; Bruland, Oyvind S.; Larsen, Roy H.

    2003-05-16T23:59:59.000Z

    The bone-seeking property of and the potential to irradiate red marrow by the alpha-particle emitter Ra-223 (t1/2 = 11.43 d) were compared to those of the beta-emitter Sr-89 (t1/2 = 50.53 d). Methods: The biodistributions of Ra-223 and Sr-89 were studied in mice. Tissue uptakes were determined at 1 h, 6 h, 1 d, 3 d, and 14 d after intravenous administration. The potential redistribution of progeny from Ra-223 located in bone was investigated. Radiation absorbed doses were calculated for soft tissues and bone. Doses were also estimated for marrow-containing cavities assuming spheric geometries. Results: We found that both Sr-89 and Ra-223 selectively concentrated on bone surfaces relative to soft tissues. The measured bone uptake of Ra-223 was slightly higher than that of Sr-89. At the 24 h time-point, the femur uptake of Ra-223 was 40.1% of the administered activity per gram tissue. The uptake in spleen and most other soft tissues was higher for Ra-223 than for Sr-89. We observed rapid clearance of Ra-223 from soft tissues within the first 24 hours, but the bone surface uptake of Ra-223 increased with time up to 24 h. Among the soft tissues, the spleen had the greatest accumulation and retention of Ra-223. The femur-to-spleen ratio increased with time, from 6.4 at 6 h to 23.7 at 3 days after injections. We found little redistribution of Ra-223 daughter products away from bone (about 2% at 6 h and less than 1% detectable at 3 d). Estimates of dose to marrow-containing cavities showed that the Ra-223 alpha-emitter might have a marrow-sparing advantage compared to beta-emitters due to high linear-energy-transfer and short alpha range targeting osteoid surfaces. The alpha-emitters irradiate a smaller fraction of the marrow-containing volumes--sparing marrow and enhancing survival of marrow cells. At the same time, the bone surfaces receives a therapeutically effective radiation dose. Conclusion: The results of this study indicate that Ra-223 is a promising candidate for high linear-energy-transfer alpha-particle irradiation of cancer cells on bone surfaces. Radium-223 can, together with its daughter radionuclides, deliver an intense and highly localized field of radiation to bone surfaces with substantially less irradiation of healthy bone marrow dose compared to standard, bone-seeking beta-emitters such as Sr-89.

  17. Nuclear fusion as a probe for octupole deformation in $^{224}$Ra

    E-Print Network [OSTI]

    Kumar, Raj; Vitturi, A

    2015-01-01T23:59:59.000Z

    $\\textit{Background}$: Nuclear fusion has been shown to be a perfect probe to study the different nuclear shapes. However, the possibility of testing octupole deformation of a nucleus with this tool has not been fully explored yet. The presence of a stactic octupole deformation in nuclei will enhanced a possible permanent electric dipole moment, leading to a possible demonstration of parity violation. $\\textit{Purpose}$: To check whether static octupole deformation or octupole vibration in fusion give qualitatively different results so that both situations can be experimentally disentangled. $\\textit{Method}$: Fusion cross sections are computed in the Coupled-Channels formalism making use of the Ingoing-Wave Boundary Conditions (IWBC) for the systems $^{16}$O+$^{144}$Ba and $^{16}$O+$^{224}$Ra. $\\textit{Results}$: Barrier distributions of the two considered schemes show different patterns. For the $^{224}$Ra case, the octupole deformation parameter is large enough to create a sizeable difference. $\\textit{Con...

  18. CT imaging of enhanced oil recovery experiments

    SciTech Connect (OSTI)

    Gall, B.L.

    1992-12-01T23:59:59.000Z

    X-ray computerized tomography (Cr) has been used to study fluid distributions during chemical enhanced oil recovery experiments. Four CT-monitored corefloods were conducted, and oil saturation distributions were calculated at various stages of the experiments. Results suggested that this technique could add significant information toward interpretation and evaluation of surfactant/polymer EOR recovery methods. CT-monitored tracer tests provided information about flow properties in the core samples. Nonuniform fluid advance could be observed, even in core that appeared uniform by visual inspection. Porosity distribution maps based on CT density calculations also showed the presence of different porosity layers that affected fluid movement through the cores. Several types of CT-monitored corefloods were conducted. Comparisons were made for CT-monitored corefloods using chemical systems that were highly successful in reducing residual oil saturations in laboratory experiments and less successful systems. Changes were made in surfactant formulation and in concentration of the mobility control polymer. Use of a poor mobility control agent failed to move oil that was not initially displaced by the injected surfactant solution; even when a good'' surfactant system was used. Use of a less favorable surfactant system with adequate mobility control could produce as much oil as the use of a good surfactant system with inadequate mobility control. The role of mobility control, therefore, becomes a critical parameter for successful application of chemical EOR. Continuation of efforts to use CT imaging in connection with chemical EOR evaluations is recommended.

  19. CT imaging of enhanced oil recovery experiments

    SciTech Connect (OSTI)

    Gall, B.L.

    1992-12-01T23:59:59.000Z

    X-ray computerized tomography (Cr) has been used to study fluid distributions during chemical enhanced oil recovery experiments. Four CT-monitored corefloods were conducted, and oil saturation distributions were calculated at various stages of the experiments. Results suggested that this technique could add significant information toward interpretation and evaluation of surfactant/polymer EOR recovery methods. CT-monitored tracer tests provided information about flow properties in the core samples. Nonuniform fluid advance could be observed, even in core that appeared uniform by visual inspection. Porosity distribution maps based on CT density calculations also showed the presence of different porosity layers that affected fluid movement through the cores. Several types of CT-monitored corefloods were conducted. Comparisons were made for CT-monitored corefloods using chemical systems that were highly successful in reducing residual oil saturations in laboratory experiments and less successful systems. Changes were made in surfactant formulation and in concentration of the mobility control polymer. Use of a poor mobility control agent failed to move oil that was not initially displaced by the injected surfactant solution; even when a ``good`` surfactant system was used. Use of a less favorable surfactant system with adequate mobility control could produce as much oil as the use of a good surfactant system with inadequate mobility control. The role of mobility control, therefore, becomes a critical parameter for successful application of chemical EOR. Continuation of efforts to use CT imaging in connection with chemical EOR evaluations is recommended.

  20. Exchange 13/14 www.ed.ac.uk

    E-Print Network [OSTI]

    Herrmann, Samuel

    : Studyabroad@ed.ac.uk Outgoing Students: Sharyn Bennet Email: Erasmus.outgoing@ed.ac.uk Head of Study Abroad

  1. ACS SYMPOSIUM SERIES 966 Rational Environmental

    E-Print Network [OSTI]

    Hammock, Bruce D.

    ACS SYMPOSIUM SERIES 966 Rational Environmental Management of Agrochemicals Risk Assessment-Bayo, Editor Chiha University Sponsored by the ACS Division of Agrochemicals American Chemical Society of agrochemicals : risk assessment, monitoring, and remedial action / Ivan R. Kennedy, editor. ..[et al

  2. Suboptimal Control Techniques for Networked Hybrid Systems S.C. Bengea, P.F. Hokayem, R.A. DeCarlo and C.T. Abdallah

    E-Print Network [OSTI]

    problem in the S.C. Bengea is with the Innovation Center, Eaton Corporation, Eden Prairie, MN, sbengea

  3. Web https://ms.ecc.utokyo.ac.jp/ (POP) popd.ecc.utokyo.ac.jp

    E-Print Network [OSTI]

    Katsumoto, Shingo

    ; 2 233 #12; (POP) popd.ecc.utokyo.ac.jp SSL995 (IMAP) imapd.ecc.utokyo.ac.jp SSL993 sbmsd.ecc.utokyo.ac.jp SSL465 @ 1. MailHosting D 2. 200MB 400MB 3. POPIMAP IMAPPOP 200MB400MB 3 233 #12;Thunderbird 3 4 233 #12; (POP) popd.ecc.utokyo.ac.jp SSL995 (IMAP) imapd.ecc.utokyo.ac.jp SSL993

  4. Friction Reduction for Microhole CT Drilling

    SciTech Connect (OSTI)

    Ken Newman; Patrick Kelleher; Edward Smalley

    2007-03-31T23:59:59.000Z

    The objective of this 24 month project focused on improving microhole coiled tubing drilling bottom hole assembly (BHA) reliability and performance, while reducing the drilling cost and complexity associated with inclined/horizontal well sections. This was to be accomplished by eliminating the need for a downhole drilling tractor or other downhole coiled tubing (CT) friction mitigation techniques when drilling long (>2,000 ft.) of inclined/horizontal wellbore. The technical solution to be developed and evaluated in this project was based on vibrating the coiled tubing at surface to reduce the friction along the length of the downhole CT drillstring. The Phase 1 objective of this project centered on determining the optimum surface-applied vibration system design for downhole CT friction mitigation. Design of the system would be based on numerical modeling and laboratory testing of the CT friction mitigation achieved with various types of surface-applied vibration. A numerical model was developed to predict how far downhole the surface-applied vibration would travel. A vibration test fixture, simulating microhole CT drilling in a horizontal wellbore, was constructed and used to refine and validate the numerical model. Numerous tests, with varying surface-applied vibration parameters were evaluated in the vibration test fixture. The data indicated that as long as the axial force on the CT was less than the helical buckling load, axial vibration of the CT was effective at mitigating friction. However, surface-applied vibration only provided a small amount of friction mitigation as the helical buckling load on the CT was reached or exceeded. Since it would be impractical to assume that routine field operations be conducted at less than the helical buckling load of the CT, it was determined that this technical approach did not warrant the additional cost and maintenance issues that would be associated with the surface vibration equipment. As such, the project was concluded following completion of Phase 1, and Phase 2 (design, fabrication, and testing of a prototype surface vibration system) was not pursued.

  5. Respiratory correlated cone beam CT

    SciTech Connect (OSTI)

    Sonke, Jan-Jakob; Zijp, Lambert; Remeijer, Peter; Herk, Marcel van [Department of Radiation Oncology, Netherlands Cancer Institute - Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands)

    2005-04-01T23:59:59.000Z

    A cone beam computed tomography (CBCT) scanner integrated with a linear accelerator is a powerful tool for image guided radiotherapy. Respiratory motion, however, induces artifacts in CBCT, while the respiratory correlated procedures, developed to reduce motion artifacts in axial and helical CT are not suitable for such CBCT scanners. We have developed an alternative respiratory correlated procedure for CBCT and evaluated its performance. This respiratory correlated CBCT procedure consists of retrospective sorting in projection space, yielding subsets of projections that each corresponds to a certain breathing phase. Subsequently, these subsets are reconstructed into a four-dimensional (4D) CBCT dataset. The breathing signal, required for respiratory correlation, was directly extracted from the 2D projection data, removing the need for an additional respiratory monitor system. Due to the reduced number of projections per phase, the contrast-to-noise ratio in a 4D scan reduced by a factor 2.6-3.7 compared to a 3D scan based on all projections. Projection data of a spherical phantom moving with a 3 and 5 s period with and without simulated breathing irregularities were acquired and reconstructed into 3D and 4D CBCT datasets. The positional deviations of the phantoms center of gravity between 4D CBCT and fluoroscopy were small: 0.13{+-}0.09 mm for the regular motion and 0.39{+-}0.24 mm for the irregular motion. Motion artifacts, clearly present in the 3D CBCT datasets, were substantially reduced in the 4D datasets, even in the presence of breathing irregularities, such that the shape of the moving structures could be identified more accurately. Moreover, the 4D CBCT dataset provided information on the 3D trajectory of the moving structures, absent in the 3D data. Considerable breathing irregularities, however, substantially reduces the image quality. Data presented for three different lung cancer patients were in line with the results obtained from the phantom study. In conclusion, we have successfully implemented a respiratory correlated CBCT procedure yielding a 4D dataset. With respiratory correlated CBCT on a linear accelerator, the mean position, trajectory, and shape of a moving tumor can be verified just prior to treatment. Such verification reduces respiration induced geometrical uncertainties, enabling safe delivery of 4D radiotherapy such as gated radiotherapy with small margins.

  6. Examination Report: OAS-RA-L-12-07 | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010Salt | DepartmentExamination Report: OAS-RA-L-12-07

  7. Audit Report: OAS-RA-10-17 | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T, Inc.'s ReplyApplication of TrainingAMOIG-074310-17 Audit Report: OAS-RA-10-17

  8. Audit Report: OAS-RA-12-06 | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T, Inc.'s ReplyApplication of TrainingAMOIG-074310-17 Audit Report:OAS-RA-12-06

  9. Audit Report: OAS-RA-L-11-08 | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T, Inc.'s ReplyApplication of TrainingAMOIG-074310-17 Audit Report:OAS-RA-12-068

  10. Audit Report: OAS-RA-L-11-09 | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T, Inc.'s ReplyApplication of TrainingAMOIG-074310-17 Audit Report:OAS-RA-12-0689

  11. Audit Report: OAS-RA-10-08 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03 Audit Report: OAS-M-15-03RA-10-08

  12. Audit Report: OAS-RA-11-02 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03 Audit Report:OAS-RA-11-02 Audit

  13. Audit Report: OAS-RA-11-03 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03 Audit Report:OAS-RA-11-02

  14. Audit Report: OAS-RA-11-11 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03 AuditAudit Report: OAS-RA-11-11

  15. Audit Report: OAS-RA-11-12 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03 AuditAudit Report: OAS-RA-11-112

  16. Audit Report: OAS-RA-11-13 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03 AuditAudit Report: OAS-RA-11-1123

  17. Audit Report: OAS-RA-L-11-02 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03 AuditAuditReport: OAS-RA-L-11-02

  18. Audit Report: OAS-RA-L-12-06 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from TarasaName4 AuditM-15-03RA-L-12-06 Audit Report:

  19. Examination Report: OAS-RA-11-18 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:RevisedAdvisoryStandardGeneration |10Examination Report: OAS-RA-11-18 Examination

  20. Examination Report: OAS-RA-13-03 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:RevisedAdvisoryStandardGeneration |10Examination Report: OAS-RA-11-18Examination

  1. Audit Report: OAS-RA-14-04 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube platform is alwaysISOSource1-01 Audit Letter Report:3894 Audit4RA-14-04 Audit

  2. Audit Report: OAS-RA-L-12-03 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube platform is alwaysISOSource1-01 Audit Letter Report:3894 Audit4RA-14-046033

  3. Audit Report: OAS-RA-L-12-06 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube platform is alwaysISOSource1-01 Audit Letter Report:3894 Audit4RA-14-046033456

  4. Special Report: OAS-RA-10-04 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOriginEducationVideo »UsageSecretaryVideos Solid-State|Special Report: OAS-RA-10-04 Special

  5. Special Report: OAS-RA-12-03 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOriginEducationVideo »UsageSecretaryVideos Solid-State|Special Report: OAS-RA-10-04

  6. Special Report: OAS-RA-13-10 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOriginEducationVideo »UsageSecretaryVideos Solid-State|Special Report: OAS-RA-10-04Special

  7. Analysis and design of a direct AC to AC matrix converter topology

    E-Print Network [OSTI]

    Choi, Sewan

    1992-01-01T23:59:59.000Z

    - eration. With the advent of the thyristor and more recent devices such as the Metal oxided semiconductor field effect transistor(MOSI'ET), the Insulated gate bipolar transistor(IGBT) and the MOS controlled thyristor(MCT), it has become increas- ingly... commutated devices such as OTO's, IGBT's, IVIOSFET's and MCT's. The principle of forced commutation is used in clirect ac to ac matrix converter which is described in the next section. B. Direct AC to AC Matrix Converter Direct ac to ac matrix converters...

  8. Comparison of CT and MR-CT Fusion for Prostate Post-Implant Dosimetry

    SciTech Connect (OSTI)

    Maletz, Kristina L. [Department of Radiation Oncology, St. Luke's-Roosevelt Hospital Center, Beth Israel Medical Center, Continuum Health Partners, New York, NY (Israel); Columbia University College of Physicians and Surgeons, New York, NY (United States); Ennis, Ronald D., E-mail: REnnis@chpnet.org [Department of Radiation Oncology, St. Luke's-Roosevelt Hospital Center, Beth Israel Medical Center, Continuum Health Partners, New York, NY (Israel); Ostenson, Jason; Pevsner, Alexander [Department of Radiation Oncology, St. Luke's-Roosevelt Hospital Center, Beth Israel Medical Center, Continuum Health Partners, New York, NY (Israel); Kagen, Alexander [Department of Radiology, Beth Israel Medical Center, St. Luke's-Roosevelt Hospital, Continuum Health Partners, New York, NY (Israel); Wernick, Iddo [Department of Radiation Oncology, St. Luke's-Roosevelt Hospital Center, Beth Israel Medical Center, Continuum Health Partners, New York, NY (Israel)

    2012-04-01T23:59:59.000Z

    Purpose: The use of T2 MR for postimplant dosimetry (PID) after prostate brachytherapy allows more anatomically accurate and precise contouring but does not readily permit seed identification. We developed a reproducible technique for performing MR-CT fusion and compared the resulting dosimetry to standard CT-based PID. Methods and Materials: CT and T1-weighted MR images for 45 patients were fused and aligned based on seed distribution. The T2-weighted MR image was then fused to the aligned T1. Reproducibility of the fusion technique was tested by inter- and intraobserver variability for 13 patients. Dosimetry was computed for the prostate as a whole and for the prostate divided into anterior and posterior sectors of the base, mid-prostate, and apex. Results: Inter- and intraobserver variability for the fusion technique showed less than 1% variation in D90. MR-CT fusion D90 and CT D90 were nearly equivalent for the whole prostate, but differed depending on the identification of superior extent of the base (p = 0.007) and on MR/CT prostate volume ratio (p = 0.03). Sector analysis showed a decrease in MR-CT fusion D90 in the anterior base (ratio 0.93 {+-}0.25, p < 0.05) and an increase in MR-CT fusion D90 in the apex (p < 0.05). The volume of extraprostatic tissue encompassed by the V100 is greater on MR than CT. Factors associated with this difference are the MR/CT volume ratio (p < 0.001) and the difference in identification of the inferior extent of the apex (p = 0.03). Conclusions: We developed a reproducible MR-CT fusion technique that allows MR-based dosimetry. Comparing the resulting postimplant dosimetry with standard CT dosimetry shows several differences, including adequacy of coverage of the base and conformity of the dosimetry around the apex. Given the advantage of MR-based tissue definition, further study of MR-based dosimetry is warranted.

  9. Rapid Reagentless Detection of M. tuberculosis H37Ra in Respiratory Effluents

    SciTech Connect (OSTI)

    Adams, K L; Steele, P T; Bogan, M J; Sadler, N M; Martin, S; Martin, A N; Frank, M

    2008-01-29T23:59:59.000Z

    Two similar mycobacteria, Mycobacteria tuberculosis H37Ra and Mycobacteria smegmatis are rapidly detected and identified within samples containing a complex background of respiratory effluents using Single Particle Aerosol Mass Spectrometry (SPAMS). M. tuberculosis H37Ra (TBa), an avirulent strain, is used as a surrogate for virulent tuberculosis (TBv); M. smegmatis (MSm) is utilized as a near neighbor confounder for TBa. Bovine lung surfactant and human exhaled breath condensate are used as first-order surrogates for infected human lung expirations from patients with pulmonary tuberculosis. This simulated background sputum is mixed with TBa or MSm and nebulized to produce conglomerate aerosol particles, single particles that contain a bacterium embedded within a background respiratory matrix. Mass spectra of single conglomerate particles exhibit ions associated with both respiratory effluents and mycobacteria. Spectral features distinguishing TBa from MSm in pure and conglomerate particles are shown. SPAMS pattern matching alarm algorithms are able to distinguish TBa containing particles from background matrix and MSm for >50% of the test particles, which is sufficient to enable a high probability of detection and a low false alarm rate if an adequate number of such particles are present. These results indicate the potential usefulness of SPAMS for rapid, reagentless tuberculosis screening.

  10. abdominal multislice ct: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    planning. It includes an abdominal computer tomography (CT) image Leow, Wee Kheng 17 CT-PET Landmark-based Lung Registration Using a Dynamic Breathing Model S. Chambon1 Physics...

  11. abdominal ct images: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    methods establish microCT imaging as a useful tool for comparative Metscher, Brian 31 CT-PET Landmark-based Lung Registration Using a Dynamic Breathing Model S. Chambon1 Physics...

  12. abdominal ct findings: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    planning. It includes an abdominal computer tomography (CT) image Leow, Wee Kheng 11 CT-PET Landmark-based Lung Registration Using a Dynamic Breathing Model S. Chambon1 Physics...

  13. Soft switched high frequency ac-link converter 

    E-Print Network [OSTI]

    Balakrishnan, Anand Kumar

    2009-05-15T23:59:59.000Z

    topology for medium and high power ac-ac, ac-dc and dc-ac applications. An ac-link formed by an inductor-capacitor pair replaces the conventional dc-link. Each leg of the converter is formed by two bidirectional switches. Power transfer from input to output...

  14. Anatomic measurement accuracy: CT parameters and 3D rendering effects

    E-Print Network [OSTI]

    Vorperian, Houri K.

    Anatomic measurement accuracy: CT parameters and 3D rendering effects Brian J Whyms a, E Michael of Neuroscience #12;INTRODUCTION · Measurements from 3D-CT rendering are used in research and clinical management-CT rendering techniques on measurements #12;METHODS Scanned: · 3 human mandibles · a phantom object Phantom

  15. RHIC spin flipper AC dipole controller

    SciTech Connect (OSTI)

    Oddo, P.; Bai, M.; Dawson, C.; Gassner, D.; Harvey, M.; Hayes, T.; Mernick, K.; Minty, M.; Roser, T.; Severino, F.; Smith, K.

    2011-03-28T23:59:59.000Z

    The RHIC Spin Flipper's five high-Q AC dipoles which are driven by a swept frequency waveform require precise control of phase and amplitude during the sweep. This control is achieved using FPGA based feedback controllers. Multiple feedback loops are used to and dynamically tune the magnets. The current implementation and results will be presented. Work on a new spin flipper for RHIC (Relativistic Heavy Ion Collider) incorporating multiple dynamically tuned high-Q AC-dipoles has been developed for RHIC spin-physics experiments. A spin flipper is needed to cancel systematic errors by reversing the spin direction of the two colliding beams multiple times during a store. The spin flipper system consists of four DC-dipole magnets (spin rotators) and five AC-dipole magnets. Multiple AC-dipoles are needed to localize the driven coherent betatron oscillation inside the spin flipper. Operationally the AC-dipoles form two swept frequency bumps that minimize the effect of the AC-dipole dipoles outside of the spin flipper. Both AC bumps operate at the same frequency, but are phase shifted from each other. The AC-dipoles therefore require precise control over amplitude and phase making the implementation of the AC-dipole controller the central challenge.

  16. Comparison of CT, PET, and PET/CT for Staging of Patients with Indolent Non-Hodgkin’s Lymphoma

    E-Print Network [OSTI]

    Fueger, Barbara J.; Yeom, Kristen; Czernin, Johannes; Sayre, James W.; Phelps, Michael E.; Allen-Auerbach, Martin S.

    2009-01-01T23:59:59.000Z

    B. J. Fueger et al. : PET/CT for indolent lymphoma Table 2.Performance for detection of nodal disease Sensitivity PETCT PET/CT pG0.001 vs PET, CT Specificity pG0.001 vs PET

  17. High frequency AC power converter for low voltage circuits

    E-Print Network [OSTI]

    Salazar, Nathaniel Jay Tobias

    2012-01-01T23:59:59.000Z

    This thesis presents a novel AC power delivery architecture that is suitable for VHF frequency (50-100MHz) polyphase AC/DC power conversion in low voltage integrated circuits. A complete AC power delivery architecture was ...

  18. Alamouti {yjdong, sky6174}@ccl.snu.ac.kr, jsno@snu.ac.kr, djshin@hanyang.ac.kr

    E-Print Network [OSTI]

    No, Jong-Seon

    @snu.ac.kr, djshin@hanyang.ac.kr (soft-decision-and-forward: SDF) . SDF . Alamouti , . (amplify-and-forward: AF) . , SDF AF . 1. . (source: S-decision-and-forward: SDF) . SDF R S phase, phase 1 phase 2 . Phase 1, S R D , phase 2 R D . , S D

  19. AC Transit | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The Future of1 A Strategic Framework for SMRA View from the-1AssessmentAC

  20. ac magnetohydrodynamic microfluidic: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Keywords: electrokinetics, AC Electro-osmosis (ACEO); electrode polarization; microfluidics. 1. Introduction During recent years, AC electro-osmosis (ACEO) has emerged as a...

  1. ac iontophoretic transport: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Keywords: electrokinetics, AC Electro-osmosis (ACEO); electrode polarization; microfluidics. 1. Introduction During recent years, AC electro-osmosis (ACEO) has emerged as a...

  2. AVTA: Clipper Creek AC Level 2 Charging System Testing Results...

    Broader source: Energy.gov (indexed) [DOE]

    electric vehicles. This research was conducted by Idaho National Laboratory. Clipper Creek AC Level 2 - February 2012 More Documents & Publications AVTA: Aerovironment AC Level...

  3. ac traction drives: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solid State Transformer Engineering Websites Summary: converters as distribution transformers 1. A power electronics-based solid state transformer (SST) providesAc-Ac Dual...

  4. www.accommodation.salford.ac.uk Accommodation

    E-Print Network [OSTI]

    Romano, Daniela

    sets out the main elements of good management practice. It covers health and safety, maintenancewww.accommodation.salford.ac.uk Accommodation Guide to University and University partner accommodation #12;32 www.accommodation.salford.ac.ukA guide to University and Partner accommodation Welcome

  5. Printing and Scanning Instructions Printing on Savin (reserved for Job Market/RA/TA print jobs ONLY)

    E-Print Network [OSTI]

    Niebur, Ernst

    1 Printing and Scanning Instructions Printing on Savin (reserved for Job Market/RA/TA print jobs, stapling, or three holes punch, you can find them under the "Layout" tab and "Advanced". #12;2 Scanning on Savin (NOTE: scanning is Free of Charge) A feature of the new copier is the option of using it to scan

  6. NIH eRA System xTrain Termination for Appointments Quick Reference 1 January 27, 2011

    E-Print Network [OSTI]

    Baker, Chris I.

    NIH eRA System xTrain Termination for Appointments Quick Reference 1 January 27, 2011 Powering the Advancement of Science xTrain Termination of Appointments Quick Reference Guide for Institution Users 1. The PD/PI Initiates a Termination Notice (TN) · The PD/PI locates the Trainee on the Trainee Roster

  7. NIH eRA System xTrain External Termination of Fellowships Quick Reference 1 January 27, 2011

    E-Print Network [OSTI]

    Baker, Chris I.

    NIH eRA System xTrain External Termination of Fellowships Quick Reference 1 January 27, 2011 Powering the Advancement of Science xTrain Termination of Fellowships Quick Reference Guide for Institution finds the Fellowship award to be terminated and selects the View Trainee Roster link. NOTE: Although

  8. Microfluidics for block polymer shells (DMR 0819860) SEED :H.A. Stone, R.A. Register and Janine Nunes

    E-Print Network [OSTI]

    Petta, Jason

    Microfluidics for block polymer shells (DMR 0819860) SEED :H.A. Stone, R.A. Register and Janine. We utilized microfluidic methods to investigate the role of geometric structures, e.g. thin spherical, microfluidic devices with two consecutive flow-focusing junctions were used to generate air bubble

  9. Howell, R.A., 2012 Living with a carbon allowance 1 Living with a carbon allowance: the experiences of Carbon

    E-Print Network [OSTI]

    Howell, R.A., 2012 Living with a carbon allowance 1 Living with a carbon allowance: the experiences of Carbon Rationing Action Groups and implications for policy Rachel A. Howell Environmental Change with a carbon allowance: the experiences of Carbon Rationing Action Groups and implications for policy. Energy

  10. 1997 BNL Site Environmental Report E -1 Bari, R.A., Gordon, D., Moran, D., and Volkow, N.,

    E-Print Network [OSTI]

    APPENDIX E 1997 BNL Site Environmental Report E - 1 Bari, R.A., Gordon, D., Moran, D., and Volkow, N., 1997. Report of the Ad Hoc Committee on Environmental, Safety, and Health Decision Making at Brookhaven National Laboratory (April 29, 1997). Brookhaven National Laboratory, 1997. Environmental

  11. An experimental and numerical study of surface tension-driven melt flow R.A. Parsons a,, F. Nimmo a

    E-Print Network [OSTI]

    Nimmo, Francis

    An experimental and numerical study of surface tension-driven melt flow R.A. Parsons a,, F. Nimmo 2007 Abstract To determine the role of surface tension-driven melt migration in planetary bodies, we, surface tension causes the melt to relax back to a homogeneous distribution. Samples composed of 76 vol

  12. (5202) e-mail: takasaki.midori@ocha.ac.jp (5201) e-mail: iwasaki.ogihara.chizuru@ocha.ac.jp

    E-Print Network [OSTI]

    Matsuzaki, Katsuhiko

    .chika@ocha.ac.jp = (5215) e-mail: schwartz.laure@ocha.ac.jp (5182) e-mail: kanda.yutsuki@ocha.ac.jp (5181) e

  13. Complications in CT-guided Procedures: Do We Really Need Postinterventional CT Control Scans?

    SciTech Connect (OSTI)

    Nattenmüller, Johanna, E-mail: johanna.nattenmueller@med.uni-heidelberg.de; Filsinger, Matthias, E-mail: Matthias_filsinger@web.de; Bryant, Mark, E-mail: mark.bryant@med.uni-heidelberg.de; Stiller, Wolfram, E-mail: Wolfram.Stiller@med.uni-heidelberg.de; Radeleff, Boris, E-mail: boris.radeleff@med.uni-heidelberg.de; Grenacher, Lars, E-mail: lars.grenacher@med.uni-heidelberg.de; Kauczor, Hans-Ullrich, E-mail: hu.kauczor@med.uni-heidelberg.de; Hosch, Waldemar, E-mail: waldemar.hosch@urz.uni-heidelberg.de [University Hospital Heidelberg, Department of Diagnostic and Interventional Radiology (Germany)

    2013-06-19T23:59:59.000Z

    PurposeThe aim of this study is twofold: to determine the complication rate in computed tomography (CT)-guided biopsies and drainages, and to evaluate the value of postinterventional CT control scans.MethodsRetrospective analysis of 1,067 CT-guided diagnostic biopsies (n = 476) and therapeutic drainages (n = 591) in thoracic (n = 37), abdominal (n = 866), and musculoskeletal (ms) (n = 164) locations. Severity of any complication was categorized as minor or major. To assess the need for postinterventional CT control scans, it was determined whether complications were detected clinically, on peri-procedural scans or on postinterventional scans only.ResultsThe complication rate was 2.5 % in all procedures (n = 27), 4.4 % in diagnostic punctures, and 1.0 % in drainages; 13.5 % in thoracic, 2.0 % in abdominal, and 3.0 % in musculoskeletal procedures. There was only 1 major complication (0.1 %). Pneumothorax (n = 14) was most frequent, followed by bleeding (n = 9), paresthesia (n = 2), material damage (n = 1), and bone fissure (n = 1). Postinterventional control acquisitions were performed in 65.7 % (701 of 1,067). Six complications were solely detectable in postinterventional control acquisitions (3 retroperitoneal bleeds, 3 pneumothoraces); all other complications were clinically detectable (n = 4) and/or visible in peri-interventional controls (n = 21).ConclusionComplications in CT-guided interventions are rare. Of these, thoracic interventions had the highest rate, while pneumothoraces and bleeding were most frequent. Most complications can be detected clinically or peri-interventionally. To reduce the radiation dose, postinterventional CT controls should not be performed routinely and should be restricted to complicated or retroperitoneal interventions only.

  14. Renal infarction: CT diagnosis and correlation between CT findings and etiologies

    SciTech Connect (OSTI)

    Wong, W.S.; Moss, A.A.; Federle, M.P.; Cochran, S.T.; London, S.S.

    1984-01-01T23:59:59.000Z

    The CT scans and the clinical records of 12 patients who had renal infarction were reviewed. The renal infarcts were classified as either focal or global. The CT findings were correlated with the etiologies of renal infarction. Embolism was the most common cause of renal infarcts that were multifocal with involvement of both kidneys. Trauma caused a unilateral global type of infract. A case of sickle cell anemia presented with multiple ''slit-like'' focal infarcts and enlarged kidneys. Forty-seven per cent of infarcts demonstrated the cortical rim sign, 11% were acapsular fluid collection, and 6% had an abnormally thickened renal fascia.

  15. www.mmu.ac.uk/careers Careers & Employability Service

    E-Print Network [OSTI]

    .mmu.ac.uk/careers Identifying courses · www.prospects.ac.uk/search_courses.htm · www.jobs.ac.uk · www.Findamasters.com · www.mmu.ac.uk/careers PG Professional/Vocational courses: Courses to allow you to enter certain professions Courses involve lectures for the first two terms then a research project for the final term (often finishing after

  16. aneurysm ct evaluation: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    die Magnetresonanztomographie und die Positronen-Emissionstomographie ( CT, MRT, PET) sind heute, neben der Ultraschalltechnik, die wichtigsten nicht-invasiven bildgebenden...

  17. aided ct image: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Imaging X-rays Computed Tomography (CT) Positron Emission Tomography (PET 12;LSO-APD Array Schematic 12;Time-of-Flight PET 12;Energy Spectrum with lutetium...

  18. Segmentation of artifacts and anatomy in CT metal artifact reduction

    E-Print Network [OSTI]

    Karimi, Seemeen; Cosman, Pamela; Wald, Christoph; Martz, Harry

    2012-01-01T23:59:59.000Z

    Maximum- likelihood dual-energy tomographic imageartifact reduction by dual energy CT using monoenergetictive reconstruction of dual energy data 21 has the potential

  19. CT. L-2 United States Government

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp -KWatertowni5W 95.5x-L* d! CT NC0 - i ,

  20. Sclerosing angiomatoid nodular transformation of the spleen: CT, MR, PET, and 99mTc-sulfur colloid SPECT CT findings with gross and histopathological correlation

    E-Print Network [OSTI]

    Thacker, Curtis; Korn, Ronald; Millstine, John; Harvin, Howard; Lier Ribbink, Jeffrey A.; Gotway, Michael B.

    2010-01-01T23:59:59.000Z

    computed tomography-CT (FDG-PET CT) survey which revealed aof the spleen: CT, MR, PET, and 99m Tc-sulfur colloid SPECTT2, no enhancement US CT MR FDG-PET N/A › uptake N/A N/A N/A

  1. Automated movement correction for dynamic PET/CT images: Evaluation with phantom and patient data

    E-Print Network [OSTI]

    2014-01-01T23:59:59.000Z

    co- registration between PET and CT and for between frameco-registration between PET and CT, the PET images with ACregistration between PET and CT. Figure 3 shows that small

  2. Radioimmuntherapie3 Radioimmundiagnostik (Immuno-PET/CT)3

    E-Print Network [OSTI]

    Gollisch, Tim

    Radioimmuntherapie3 Radioimmundiagnostik (Immuno-PET/CT)3 Entzündungsdiagnostik mit [18F]FDG3 of Inflammatory Diseases with [18F]FDG3 Characterisation of Multinodular Toxic Goiter3 Radioactive tracers onkologischer Therapiekonzepte Radioimmunotherapy3 Radioimmunodiagnostics (Immuno-PET/CT)3 Diagnosis

  3. Three phase AC motor controller

    DOE Patents [OSTI]

    Vuckovich, Michael (Elizabeth, PA); Wright, Maynard K. (Bethel Park, PA); Burkett, John P. (South Huntington Township, Westmoreland County, PA)

    1984-03-20T23:59:59.000Z

    A motor controller for a three phase AC motor (10) which is adapted to operate bidirectionally from signals received either from a computer (30) or a manual control (32). The controller is comprised of digital logic circuit means which implement a forward and reverse command signal channel (27, 29) for the application of power through the forward and reverse power switching relays (16, 18, 20, 22). The digital logic elements are cross coupled to prevent activation of both channels simultaneously and each includes a plugging circuit (65, 67) for stopping the motor upon the removal of control signal applied to one of the two channels (27, 29) for a direction of rotation desired. Each plugging circuit (65, 67) includes a one-shot pulse signal generator (88, 102) which outputs a single pulse signal of predetermined pulsewidth which is adapted to inhibit further operation of the application of power in the channel which is being activated and to apply a reversal command signal to the other channel which provides a reversed phase application of power to the motor for a period defined by the pulse-width output of the one-shot signal generator to plug the motor (10) which will then be inoperative until another rotational command signal is applied to either of the two channels.

  4. Multi-energy CT Based on a Prior Rank, Intensity and Sparsity Model (PRISM)

    E-Print Network [OSTI]

    Soatto, Stefano

    -color, as a natural extension of dual energy CT [1], the future of CT will be multi-energy, generating much richer

  5. High-Linear Energy Transfer Irradiation Targeted to Skeletal Metastases by the Alpha Emitter Ra-223: Adjuvant or Alternative to Conventional Modalities?

    SciTech Connect (OSTI)

    Bruland, Oyvind S.; Nilsson, Sten; Fisher, Darrell R.; Larsen, Roy H.

    2006-10-15T23:59:59.000Z

    The bone-seeking, alpha-particle emitting radiopharmaceutical Alpharadin, 223RaCl2 (t1/2 = 11.4 days) is under clinical development as a novel treatment for skeletal metastases from breast and prostate cancer. This paper summarizes the current status of preclinical and clinical research on 223RaCl2. Potential advantages of 223Ra to that of external beam irradiation or registered beta-emitting bone-seekers are discussed. Published data of 223Ra dosimetry in mice and a therapeutic study in a skeletal metastases model in nude rats have indicated significant therapeutic potential of bone-seeking alpha-emitters. This paper provides short-term and long-term results from the first clinical single dosage trial. We present data from a repeated dosage study of five consecutive injections of 50 kBq/kg bodyweight, once every third week, or two injections of 125 kBq/kg bodyweight, six weeks apart. Furthermore, preliminary results are given for a randomized phase II trial involving 64 patients with hormone-refractory prostate cancer and painful skeletal metastases who received four monthly injections of 223Ra or saline as an adjuvant to external beam radiotherapy. Also presented are preliminary dose estimates for 223Ra in humans. Results indicate that repeated dosing is feasible and that opportunities are available for combined treatment strategies.

  6. Ab initio study of radium monofluoride, RaF, as a candidate to search for P- and T,P- violation effects

    E-Print Network [OSTI]

    A. D. Kudashov; A. N. Petrov; L. V. Skripnikov; N. S. Mosyagin; T. A. Isaev; R. Berger; A. V. Titov

    2014-09-20T23:59:59.000Z

    Relativistic ab initio calculations have been performed to assess the suitability of RaF for experimental search of P- and T,P-violating interactions. The parameters of P- and T,P-odd terms of the spin-rotational Hamiltonian have been calculated for the ${^2}\\Sigma$ electronic ground state of RaF molecule. They include the parameter $W_a$, which is critical in experimental search for nuclear anapole moment and the parameters $W_d$ and $W_{\\rm SP}$ required to obtain restrictions on the electric dipole moment of the electron and T,P-odd scalar-pseudoscalar interactions, respectively. The parameter $X$ corresponding to the "volume effect" in the T,P$-$odd interaction of the $^{223}$Ra nuclear Schiff moment with electronic shells of RaF has also been computed. Spectroscopic and hyperfine structure constants for $^{223}$RaF and $^{223}$Ra$^+$ have been computed as well, demonstrating the accuracy of the methods employed.

  7. Cinema 16 Collection / A.C. Killip (collector)

    E-Print Network [OSTI]

    Handy, Todd C.

    Cinema 16 Collection / A.C. Killip (collector) University of British Columbia Archives #12;Table;Collection Description Cinema 16 Collection / A.C. Killip (collector). ­ 1961-1970. 1.5 cm of textual records

  8. WASEDAUNIVERSITY http://www.sci.waseda.ac.jp

    E-Print Network [OSTI]

    Kasahara, Hironori

    ://www.cse.sci.waseda.ac.jp/ http://www.ase.sci.waseda.ac.jp/ http://www.waseda.jp/ips/ http://www.waseda.jp/weee/ INDEX 2014 5

  9. Low-Dose Dual-Energy CT for PET Attenuation Correction with Statistical Sinogram Restoration

    E-Print Network [OSTI]

    Fessler, Jeffrey A.

    1 Low-Dose Dual-Energy CT for PET Attenuation Correction with Statistical Sinogram Restoration. of Michigan & Univ. of Washington Outline Introduction - PET/CT background - CT-based attenuation correction for PET Conventional sinogram decomposition in DE-CT Statistically motivated sinogram restoration in DE

  10. STATE OF CALIFORNIA DISTRIBUTED ENERGY STORAGE DX AC SYSTEMES ACCEPTANCE

    E-Print Network [OSTI]

    STATE OF CALIFORNIA DISTRIBUTED ENERGY STORAGE DX AC SYSTEMES ACCEPTANCE CEC-MECH-14A (Revised 08/09) CALIFORNIA ENERGY COMMISSION CERTIFICATE OF ACCEPTANCE MECH-14A NA7.5.13 Distributed Energy Storage DX AC DISTRIBUTED ENERGY STORAGE DX AC SYSTEMES ACCEPTANCE CEC-MECH-14A (Revised 08/09) CALIFORNIA ENERGY COMMISSION

  11. www.pet.hw.ac.uk 1 Private and Confidential

    E-Print Network [OSTI]

    Painter, Kevin

    www.pet.hw.ac.uk 1 Private and Confidential Application for MSc Courses - Supplementary Information of Exam Grade Attained Subjects taken at `O' level or equivalent with grades #12;www.pet.hw.ac.uk 2 of principal & subsidiary subjects Please leave blank for Institute Use #12;www.pet.hw.ac.uk 3 Employment Dates

  12. www.strath.ac.uk THIS IS YOUR

    E-Print Network [OSTI]

    Mottram, Nigel

    Building Lorna Bennet SBS Exchange Co-ordinator Michele French SBS Exchange Secretary 01 | Contents 03 Building erkan.oterkus@strath.ac.uk Lorna Bennet Strathclyde Business School Level 2, Sir William Duncan Building lorna.bennet@strath.ac.uk www.strath.ac.uk | 06 #12;Key Dates www

  13. Dynamic Bowtie for Fan-beam CT

    E-Print Network [OSTI]

    Liu, Fenglin; Cong, Wenxiang; Hsieh, Scott; Pelc, Norbert

    2013-01-01T23:59:59.000Z

    A bowtie is a filter used to shape an x-ray beam and equalize its flux reaching different detector channels. For development of spectral CT with energy-discriminative photon-counting (EDPC) detectors, here we propose and evaluate a dynamic bowtie for performance optimization based on a patient model or a scout scan. Our dynamic bowtie modifies an x-ray beam intensity profile by mechanical rotation and adaptive adjustment of the x-ray source flux. First, a mathematical model for dynamic bowtie filtering is established for an elliptical section in fan-beam geometry, and the contour of the optimal bowtie is derived. Then, numerical simulation is performed to compare the performance of the dynamic bowtie in the cases of an ideal phantom and a realistic cross-section relative to the counterparts without any bowtie and with a fixed bowtie respectively. Our dynamic bowtie can equalize the expected numbers of photons in the case of an ideal phantom. In practical cases, our dynamic bowtie can effectively reduce the dy...

  14. TLD assessment of mouse dosimetry during microCT imaging

    SciTech Connect (OSTI)

    Figueroa, Said Daibes; Winkelmann, Christopher T.; Miller, William H.; Volkert, Wynn A.; Hoffman, Timothy J. [Harry S. Truman Memorial VA Hospital, Columbia, Missouri 65201 (United States) and Department of Radiology, University of Missouri, Columbia, Missouri 65201 (United States); Department of Veterinary Pathobiology, University of Missouri, Columbia, Missouri 65201 (United States); Nuclear Science and Engineering Institute, University of Missouri, Columbia, Missouri 65201 (United States); Department of Radiology, University of Missouri, Columbia, Missouri 65201 (United States); Harry S. Truman Memorial VA Hospital, Columbia, Missouri 65201 (United States) and Departments of Internal Medicine, Chemistry, and the Nuclear Science and Engineering Institute, University of Missouri, Columbia, Missouri 65201 (United States)

    2008-09-15T23:59:59.000Z

    Advances in laboratory animal imaging have provided new resources for noninvasive biomedical research. Among these technologies is microcomputed tomography (microCT) which is widely used to obtain high resolution anatomic images of small animals. Because microCT utilizes ionizing radiation for image formation, radiation exposure during imaging is a concern. The objective of this study was to quantify the radiation dose delivered during a standard microCT scan. Radiation dose was measured using thermoluminescent dosimeters (TLDs), which were irradiated employing an 80 kVp x-ray source, with 0.5 mm Al filtration and a total of 54 mA s for a full 360 deg rotation of the unit. The TLD data were validated using a 3.2 cm{sup 3} CT ion chamber probe. TLD results showed a single microCT scan air kerma of 78.0{+-}5.0 mGy when using a poly(methylmethacrylate) (PMMA) anesthesia support module and an air kerma of 92.0{+-}6.0 mGy without the use of the anesthesia module. The validation CT ion chamber study provided a measured radiation air kerma of 81.0{+-}4.0 mGy and 97.0{+-}5.0 mGy with and without the PMMA anesthesia module, respectively. Internal TLD analysis demonstrated an average mouse organ radiation absorbed dose of 76.0{+-}5.0 mGy. The author's results have defined x-ray exposure for a routine microCT study which must be taken into consideration when performing serial molecular imaging studies involving the microCT imaging modality.

  15. Distinctly Ambitious www.hw.ac.uk

    E-Print Network [OSTI]

    Painter, Kevin

    , Duncan Hand at the James Watt Institute for High Value Manufacturing led a team to apply laser-based manufacturing processes to the production of dental products. The project led to the development of a laserDistinctly Ambitious www.hw.ac.uk Laser Machining #12;Cutting-edge engineering technology for laser

  16. Physics and contentswww.manchester.ac.uk

    E-Print Network [OSTI]

    engineering, science and bioscience research councils. As a postgraduate student at The UniversityPhysics and Astronomy #12;contentswww.manchester.ac.uk 12 The University of Manchester 2 Physics to be part of The University of Manchester. If you choose to be a postgraduate student here you can join us

  17. Four-Channel Differential AC Amplifier

    E-Print Network [OSTI]

    Kleinfeld, David

    to amplify cellular neurophysiological signals in applications requiring high gain, high input impedance, low://www.a-msystems.com General Description Instrument Features The Four-Channel Differential AC Amplifier Model 1700 is designed noise, high common-mode rejection, and powerline interference rejection. Typical applications include

  18. AC Losses of Prototype HTS Transmission Cables

    SciTech Connect (OSTI)

    Demko, J.A.; Dresner, L.; Hughey, R.L.; Lue, J.W.; Olsen, S.K.; Sinha, U.; Tolbert, J.C.

    1998-09-13T23:59:59.000Z

    Since 1995 Southwire Company and Oak Ridge National Laboratory (ORNL) have jointly designed, built, and tested nine, l-m long, high temperature superconducting (HTS) transmission cable prototypes. This paper summarizes the AC loss measurements of five of the cables not reported elsewhere, and compares the losses with each other and with theory developed by Dresner. Losses were measured with both a calorimetric and an electrical technique. Because of the broad resistive transition of the HTS tapes, the cables can be operated stably beyond their critical currents. The AC losses were measured in this region as well as below critical currents. Dresner's theory takes into account the broad resistive transition of the HTS tapes and calculates the AC losses both below and above the critical current. The two sets of AC 10SS data agree with each other and with the theory quite welL In particular, at low currents of incomplete penetration, the loss data agree with the theoretical prediction of hysteresis loss based on only the outer two Iayers carrying the total current.

  19. CT reconstruction techniques for improved accuracy of lung CT airway measurement

    SciTech Connect (OSTI)

    Rodriguez, A. [Department of Medical Physics, University of Wisconsin School of Medicine and Public Health, Madison, Wisconsin 53705 (United States); Ranallo, F. N. [Department of Medical Physics, University of Wisconsin School of Medicine and Public Health, Madison, Wisconsin 53705 and Department of Radiology, University of Wisconsin School of Medicine and Public Health, Madison, Wisconsin 53792 (United States); Judy, P. F. [Brigham and Women’s Hospital, Boston, Massachusetts 02115 (United States); Gierada, D. S. [Department of Radiology, Washington University, St. Louis, Missouri 63110 (United States); Fain, S. B., E-mail: sfain@wisc.edu [Department of Medical Physics, University of Wisconsin School of Medicine and Public Health, Madison, Wisconsin 53705 (United States); Department of Radiology, University of Wisconsin School of Medicine and Public Health, Madison, Wisconsin 53792 (United States); Department of Biomedical Engineering,University of Wisconsin School of Engineering, Madison, Wisconsin 53706 (United States)

    2014-11-01T23:59:59.000Z

    Purpose: To determine the impact of constrained reconstruction techniques on quantitative CT (qCT) of the lung parenchyma and airways for low x-ray radiation dose. Methods: Measurement of small airways with qCT remains a challenge, especially for low x-ray dose protocols. Images of the COPDGene quality assurance phantom (CTP698, The Phantom Laboratory, Salem, NY) were obtained using a GE discovery CT750 HD scanner for helical scans at x-ray radiation dose-equivalents ranging from 1 to 4.12 mSv (12–100 mA s current–time product). Other parameters were 40 mm collimation, 0.984 pitch, 0.5 s rotation, and 0.625 mm thickness. The phantom was sandwiched between 7.5 cm thick water attenuating phantoms for a total length of 20 cm to better simulate the scatter conditions of patient scans. Image data sets were reconstructed using STANDARD (STD), DETAIL, BONE, and EDGE algorithms for filtered back projection (FBP), 100% adaptive statistical iterative reconstruction (ASIR), and Veo reconstructions. Reduced (half) display field of view (DFOV) was used to increase sampling across airway phantom structures. Inner diameter (ID), wall area percent (WA%), and wall thickness (WT) measurements of eight airway mimicking tubes in the phantom, including a 2.5 mm ID (42.6 WA%, 0.4 mm WT), 3 mm ID (49.0 WA%, 0.6 mm WT), and 6 mm ID (49.0 WA%, 1.2 mm WT) were performed with Airway Inspector (Surgical Planning Laboratory, Brigham and Women’s Hospital, Boston, MA) using the phase congruency edge detection method. The average of individual measures at five central slices of the phantom was taken to reduce measurement error. Results: WA% measures were greatly overestimated while IDs were underestimated for the smaller airways, especially for reconstructions at full DFOV (36 cm) using the STD kernel, due to poor sampling and spatial resolution (0.7 mm pixel size). Despite low radiation dose, the ID of the 6 mm ID airway was consistently measured accurately for all methods other than STD FBP. Veo reconstructions showed slight improvement over STD FBP reconstructions (4%–9% increase in accuracy). The most improved ID and WA% measures were for the smaller airways, especially for low dose scans reconstructed at half DFOV (18 cm) with the EDGE algorithm in combination with 100% ASIR to mitigate noise. Using the BONE + ASIR at half BONE technique, measures improved by a factor of 2 over STD FBP even at a quarter of the x-ray dose. Conclusions: The flexibility of ASIR in combination with higher frequency algorithms, such as BONE, provided the greatest accuracy for conventional and low x-ray dose relative to FBP. Veo provided more modest improvement in qCT measures, likely due to its compatibility only with the smoother STD kernel.

  20. Dose uncertainty due to computed tomography ,,CT... slice thickness in CT-based high dose rate brachytherapy of the prostate cancer

    E-Print Network [OSTI]

    Pouliot, Jean

    Dose uncertainty due to computed tomography ,,CT... slice thickness in CT-based high dose rate in Medicine. DOI: 10.1118/1.1785454 Key words: high dose rate brachytherapy, computed tomography, prostate at risk OARs by providing three-dimensional 3D anatomical information from computed tomography CT

  1. THE ACS NEARBY GALAXY SURVEY TREASURY

    SciTech Connect (OSTI)

    Dalcanton, Julianne J.; Williams, Benjamin F.; Rosema, Keith; Gogarten, Stephanie M.; Christensen, Charlotte; Gilbert, Karoline; Hodge, Paul [Department of Astronomy, Box 351580, University of Washington, Seattle, WA 98195 (United States); Seth, Anil C. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Dolphin, Andrew [Raytheon, 1151 E. Hermans Road, Tucson, AZ 85756 (United States); Holtzman, Jon [Department of Astronomy, New Mexico State University, Box 30001, 1320 Frenger St., Las Cruces, NM 88003 (United States); Skillman, Evan D.; Weisz, Daniel [Department of Astronomy, University of Minnesota, 116 Church St. SE, Minneapolis, MN 55455 (United States); Cole, Andrew [School of Mathematics and Physics, University of Tasmania, Hobart, Tasmania (Australia); Girardi, Leo [Osservatorio Astronomico di Padova - INAF, Vicolo dell'Osservatorio 5, I-35122 Padova (Italy); Karachentsev, Igor D. [Special Astrophysical Observatory, Russian Academy of Sciences, Nizhnji Arkhyz, Karachai-Circessia Republic 369167 (Russian Federation); Olsen, Knut [NOAO, National Optical Astronomy Observatory 950 N. Cherry Ave., Tucson, AZ 85719 (United States); Freeman, Ken [Mount Stromlo Observatory, Research School of Astronomy and Astrophysics, The Australian National Univ., ACT 0200 (Australia); Gallart, Carme [Inst. de AstrofIsica de Canarias, VIa Lactea, s/n, 38200 La Laguna, Tenerife (Spain); Harris, Jason [Steward Observatory, Univ. of Arizona, 933 North Cherry Avenue, Tucson, AZ 85721 (United States); De Jong, Roelof S. [Space Telescope Science Inst., 3700 San Martin Dr., Baltimore, MD 21218 (United States)], E-mail: jd@astro.washington.edu, E-mail: ben@astro.washington.edu, E-mail: krosema@astro.washington.edu, E-mail: stephanie@astro.washington.edu, E-mail: christensen@astro.washington.edu, E-mail: fabio@astro.washington.edu, E-mail: trq@astro.washington.edu, E-mail: aseth@cfa.harvard.edu (and others)

    2009-07-15T23:59:59.000Z

    The ACS Nearby Galaxy Survey Treasury (ANGST) is a systematic survey to establish a legacy of uniform multi-color photometry of resolved stars for a volume-limited sample of nearby galaxies (D < 4 Mpc). The survey volume encompasses 69 galaxies in diverse environments, including close pairs, small and large groups, filaments, and truly isolated regions. The galaxies include a nearly complete range of morphological types spanning a factor of {approx}10{sup 4} in luminosity and star formation rate. The survey data consist of images taken with the Advanced Camera for Surveys (ACS) on the Hubble Space Telescope (HST), supplemented with archival data and new Wide Field Planetary Camera 2 (WFPC2) imaging taken after the failure of ACS. Survey images include wide field tilings covering the full radial extent of each galaxy, and single deep pointings in uncrowded regions of the most massive galaxies in the volume. The new wide field imaging in ANGST reaches median 50% completenesses of m {sub F475W} = 28.0 mag, m {sub F606W} = 27.3 mag, and m {sub F814W} = 27.3 mag, several magnitudes below the tip of the red giant branch (TRGB). The deep fields reach magnitudes sufficient to fully resolve the structure in the red clump. The resulting photometric catalogs are publicly accessible and contain over 34 million photometric measurements of >14 million stars. In this paper we present the details of the sample selection, imaging, data reduction, and the resulting photometric catalogs, along with an analysis of the photometric uncertainties (systematic and random), for both ACS and WFPC2 imaging. We also present uniformly derived relative distances measured from the apparent magnitude of the TRGB.

  2. ac-driven atomic quantum motor

    E-Print Network [OSTI]

    A. V. Ponomarev; S. Denisov; P. Hanggi

    2009-06-09T23:59:59.000Z

    We invent an ac-driven quantum motor consisting of two different, interacting ultracold atoms placed into a ring-shaped optical lattice and submerged in a pulsating magnetic field. While the first atom carries a current, the second one serves as a quantum starter. For fixed zero-momentum initial conditions the asymptotic carrier velocity converges to a unique non-zero value. We also demonstrate that this quantum motor performs work against a constant load.

  3. Direct amplitude detuning measurement with ac dipole

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    White, S.; Maclean, E.; Tomás, R.

    2013-07-01T23:59:59.000Z

    In circular machines, nonlinear dynamics can impact parameters such as beam lifetime and could result in limitations on the performance reach of the accelerator. Assessing and understanding these effects in experiments is essential to confirm the accuracy of the magnetic model and improve the machine performance. A direct measurement of the machine nonlinearities can be obtained by characterizing the dependency of the tune as a function of the amplitude of oscillations (usually defined as amplitude detuning). The conventional technique is to excite the beam to large amplitudes with a single kick and derive the tune from turn-by-turn data acquired with beam position monitors. Although this provides a very precise tune measurement it has the significant disadvantage of being destructive. An alternative, nondestructive way of exciting large amplitude oscillations is to use an ac dipole. The perturbation Hamiltonian in the presence of an ac dipole excitation shows a distinct behavior compared to the free oscillations which should be correctly taken into account in the interpretation of experimental data. The use of an ac dipole for direct amplitude detuning measurement requires careful data processing allowing one to observe the natural tune of the machine; the feasibility of such a measurement is demonstrated using experimental data from the Large Hadron Collider. An experimental proof of the theoretical derivations based on measurements performed at injection energy is provided as well as an application of this technique at top energy using a large number of excitations on the same beam.

  4. Realistic simulation of reduced-dose CT with noise modeling and sinogram synthesis using DICOM CT images

    SciTech Connect (OSTI)

    Won Kim, Chang [Interdisciplinary Program of Bioengineering Major Seoul National University College of Engineering, San 56-1, Silim-dong, Gwanak-gu, Seoul 152-742, South Korea and Institute of Radiation Medicine, Seoul National University College of Medicine, 28, Yongon-dong, Chongno-gu, Seoul 110-744 (Korea, Republic of)] [Interdisciplinary Program of Bioengineering Major Seoul National University College of Engineering, San 56-1, Silim-dong, Gwanak-gu, Seoul 152-742, South Korea and Institute of Radiation Medicine, Seoul National University College of Medicine, 28, Yongon-dong, Chongno-gu, Seoul 110-744 (Korea, Republic of); Kim, Jong Hyo, E-mail: kimjhyo@snu.ac.kr [Department of Radiology, Institute of Radiation Medicine, Seoul National University College of Medicine, 28, Yongon-dong, Chongno-gu, Seoul, 110-744 (Korea, Republic of); Department of Transdisciplinary Studies, Graduate School of Convergence Science and Technology, Seoul National University, Suwon, Gyeonggi-do, 443-270 (Korea, Republic of); Advanced Institutes of Convergence Technology, Seoul National University, Suwon, Gyeonggi-do, 443-270 (Korea, Republic of)

    2014-01-15T23:59:59.000Z

    Purpose: Reducing the patient dose while maintaining the diagnostic image quality during CT exams is the subject of a growing number of studies, in which simulations of reduced-dose CT with patient data have been used as an effective technique when exploring the potential of various dose reduction techniques. Difficulties in accessing raw sinogram data, however, have restricted the use of this technique to a limited number of institutions. Here, we present a novel reduced-dose CT simulation technique which provides realistic low-dose images without the requirement of raw sinogram data. Methods: Two key characteristics of CT systems, the noise equivalent quanta (NEQ) and the algorithmic modulation transfer function (MTF), were measured for various combinations of object attenuation and tube currents by analyzing the noise power spectrum (NPS) of CT images obtained with a set of phantoms. Those measurements were used to develop a comprehensive CT noise model covering the reduced x-ray photon flux, object attenuation, system noise, and bow-tie filter, which was then employed to generate a simulated noise sinogram for the reduced-dose condition with the use of a synthetic sinogram generated from a reference CT image. The simulated noise sinogram was filtered with the algorithmic MTF and back-projected to create a noise CT image, which was then added to the reference CT image, finally providing a simulated reduced-dose CT image. The simulation performance was evaluated in terms of the degree of NPS similarity, the noise magnitude, the bow-tie filter effect, and the streak noise pattern at photon starvation sites with the set of phantom images. Results: The simulation results showed good agreement with actual low-dose CT images in terms of their visual appearance and in a quantitative evaluation test. The magnitude and shape of the NPS curves of the simulated low-dose images agreed well with those of real low-dose images, showing discrepancies of less than +/?3.2% in terms of the noise power at the peak height and +/?1.2% in terms of the spatial frequency at the peak height. The magnitudes of the noise measured for 12 different combinations the phantom size, tube current, and reconstruction kernel for the simulated and real low-dose images were very similar, with differences of 0.1 to 4.7%. Thep value for a statistical testing of the difference in the noise magnitude ranged from 0.99 to 0.11, showing that there was no difference statistically between the noise magnitudes of the real and simulated low-dose images using our method. The strength and pattern of the streak noise in an anthropomorphic phantom was also consistent with expectations. Conclusions: A novel reduced-dose CT simulation technique was developed which uses only CT images while not requiring raw sinogram data. Our method can provide realistic simulation results under reduced-dose conditions both in terms of the noise magnitude and the textual appearance. This technique has the potential to promote clinical research for patient dose reductions.

  5. Unusual association of alveolar rhabdomyosarcoma with pancreatic metastasis: emerging role of PET-CT in tumor staging

    E-Print Network [OSTI]

    2010-01-01T23:59:59.000Z

    Christie R, Daw NC et al ( 2005) PET/CT in the evaluation ofComparative study of FDG PET/CT and conventional imaging inet al (2009) Diagnostic value of PET/CT for the staging and

  6. Estimated cumulative radiation dose from PET/CT in children with malignancies: reply to Gelfand et al

    E-Print Network [OSTI]

    Chawla, Soni C.; Boechat, M. Ines; McNitt-Gray, Michael

    2010-01-01T23:59:59.000Z

    radiation dose from PET/CT in children with malignancies.radiation dose from PET/CT in children with malig- nancies:radiation dose from PET/CT in children with malignancies:

  7. Molecular imaging in oncology: the acceptance of PET/CT and the emergence of MR/PET imaging

    E-Print Network [OSTI]

    Schiepers, Christiaan; Dahlbom, Magnus

    2011-01-01T23:59:59.000Z

    only [2] to combining PET and CT [3] and PET and MRI [4].varies widely between PET and CT, e.g. arms up or down,body imaging with MRI or PET/CT: the future for single-

  8. Estimated cumulative radiation dose from PET/CT in children with malignancies: a 5-year retrospective review

    E-Print Network [OSTI]

    2010-01-01T23:59:59.000Z

    N, Feig SA (2007) PET/CT in the evaluating pediatriccan be used for both PET and CT studies. The ALARA principleMB, Christie R, Daw NC (2005) PET/CT in the evaluation of

  9. Unusual association of alveolar rhabdomyosarcoma with pancreatic metastasis: emerging role of PET-CT in tumor staging

    E-Print Network [OSTI]

    2010-01-01T23:59:59.000Z

    The combination of PET and CT provided a mean effective doseChristie R, Daw NC et al ( 2005) PET/CT in the evaluation ofComparative study of FDG PET/CT and conventional imaging in

  10. Automatic CT simulation optimization for radiation therapy: A general strategy

    SciTech Connect (OSTI)

    Li, Hua, E-mail: huli@radonc.wustl.edu; Chen, Hsin-Chen; Tan, Jun; Gay, Hiram; Michalski, Jeff M.; Mutic, Sasa [Department of Radiation Oncology, Washington University, St. Louis, Missouri 63110 (United States)] [Department of Radiation Oncology, Washington University, St. Louis, Missouri 63110 (United States); Yu, Lifeng [Department of Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States)] [Department of Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States); Anastasio, Mark A. [Department of Biomedical Engineering, Washington University, St. Louis, Missouri 63110 (United States)] [Department of Biomedical Engineering, Washington University, St. Louis, Missouri 63110 (United States); Low, Daniel A. [Department of Radiation Oncology, University of California Los Angeles, Los Angeles, California 90095 (United States)] [Department of Radiation Oncology, University of California Los Angeles, Los Angeles, California 90095 (United States)

    2014-03-15T23:59:59.000Z

    Purpose: In radiation therapy, x-ray computed tomography (CT) simulation protocol specifications should be driven by the treatment planning requirements in lieu of duplicating diagnostic CT screening protocols. The purpose of this study was to develop a general strategy that allows for automatically, prospectively, and objectively determining the optimal patient-specific CT simulation protocols based on radiation-therapy goals, namely, maintenance of contouring quality and integrity while minimizing patient CT simulation dose. Methods: The authors proposed a general prediction strategy that provides automatic optimal CT simulation protocol selection as a function of patient size and treatment planning task. The optimal protocol is the one that delivers the minimum dose required to provide a CT simulation scan that yields accurate contours. Accurate treatment plans depend on accurate contours in order to conform the dose to actual tumor and normal organ positions. An image quality index, defined to characterize how simulation scan quality affects contour delineation, was developed and used to benchmark the contouring accuracy and treatment plan quality within the predication strategy. A clinical workflow was developed to select the optimal CT simulation protocols incorporating patient size, target delineation, and radiation dose efficiency. An experimental study using an anthropomorphic pelvis phantom with added-bolus layers was used to demonstrate how the proposed prediction strategy could be implemented and how the optimal CT simulation protocols could be selected for prostate cancer patients based on patient size and treatment planning task. Clinical IMRT prostate treatment plans for seven CT scans with varied image quality indices were separately optimized and compared to verify the trace of target and organ dosimetry coverage. Results: Based on the phantom study, the optimal image quality index for accurate manual prostate contouring was 4.4. The optimal tube potentials for patient sizes of 38, 43, 48, 53, and 58 cm were 120, 140, 140, 140, and 140 kVp, respectively, and the corresponding minimum CTDIvol for achieving the optimal image quality index 4.4 were 9.8, 32.2, 100.9, 241.4, and 274.1 mGy, respectively. For patients with lateral sizes of 43–58 cm, 120-kVp scan protocols yielded up to 165% greater radiation dose relative to 140-kVp protocols, and 140-kVp protocols always yielded a greater image quality index compared to the same dose-level 120-kVp protocols. The trace of target and organ dosimetry coverage and the ? passing rates of seven IMRT dose distribution pairs indicated the feasibility of the proposed image quality index for the predication strategy. Conclusions: A general strategy to predict the optimal CT simulation protocols in a flexible and quantitative way was developed that takes into account patient size, treatment planning task, and radiation dose. The experimental study indicated that the optimal CT simulation protocol and the corresponding radiation dose varied significantly for different patient sizes, contouring accuracy, and radiation treatment planning tasks.

  11. ac to dc converters: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to use solid state Inverters(DC to AC converters) to have a variable voltage, fixed or variable frequency power source available for industrial applications. With advancements...

  12. AUV {gslee, sbahk}@netlab.snu.ac.kr

    E-Print Network [OSTI]

    Bahk, Saewoong

    AUV , {gslee, sbahk}@netlab.snu.ac.kr Transmission Power Control in Cluster AUV (CH) AUV . 1 . 1. 2. 3 . AUV CH (Buoy

  13. University Policy No.: AC1145 Classification: Academic and Students

    E-Print Network [OSTI]

    Victoria, University of

    University Policy No.: AC1145 Classification: Academic and Students Approving Authority, interdisciplinary programs, divisions, and the library) will undergo a review every five to seven years

  14. University Policy No.: AC1150 Classification: Academic and Students

    E-Print Network [OSTI]

    Victoria, University of

    University Policy No.: AC1150 Classification: Academic and Students TEACHING, portfolios, references, library resources, laboratories and equipment) related to the subject matter

  15. WASEDAUNIVERSITY http://www.sci.waseda.ac.jp/research/

    E-Print Network [OSTI]

    Kasahara, Hironori

    ://www.ase.sci.waseda.ac.jp/ http://www.waseda.jp/ips/ http://www.waseda.jp/weee/ INDEX 2015 5 2 31http

  16. ac conductivity studies: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Last updated 8 Plotkin, Joshua B. 40 Study of supplementary controls for embedded HVDC links in a AC power system. Open Access Theses and Dissertations Summary: ??This...

  17. ac line conditioners: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of lines . ..2 Main Terasoma, Tomohide 83 Study of supplementary controls for embedded HVDC links in a AC power system. Open Access Theses and Dissertations Summary: ??This...

  18. ac losses: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    23 24 25 Next Page Last Page Topic Index 1 Transport AC loss in high temperature superconducting coils University of Cambridge - Dspace Summary: 's electromagnetic properties and...

  19. RAPIDLY MOVING DIVERTOR PLATES IN A TOKAMAK S.J. Zweben, R.A. Ellis, P. Titus, A. Xing, H. Zhang

    E-Print Network [OSTI]

    Princeton Plasma Physics Laboratory

    RAPIDLY MOVING DIVERTOR PLATES IN A TOKAMAK S.J. Zweben, R.A. Ellis, P. Titus, A. Xing, H. Zhang to replace conventional actively cooled tokamak divertor plates with a set of rapidly moving, passively inertia for ~10-30 sec, and would then be removed from the vessel for processing. When outside the tokamak

  20. Heating Greenhouses1 D.E. Buffington, R.A. Bucklin, R.W. Henley and D.B. McConnell2

    E-Print Network [OSTI]

    Watson, Craig A.

    AE11 Heating Greenhouses1 D.E. Buffington, R.A. Bucklin, R.W. Henley and D.B. McConnell2 1 supplemental heat is required. Obviously there are many ways this can be accomplished from the standpoint of these factors be considered when selecting and installing a heating system. HEATING SYSTEMS Greenhouse heating

  1. Comment on `Update of 40K and 226Ra and 232Th series $\\gamma$-to-dose conversion factors for soil'

    E-Print Network [OSTI]

    Malins, Alex; Saito, Kimiaki

    2015-01-01T23:59:59.000Z

    A letter to the editor of the Journal of Environmental Radioactivity on the article: E. Gasser, A. Nachab, A. Nourreddine, Ch. Roy, and A. Sellam, `Update of 40K and 226Ra and 232Th series $\\gamma$-to-dose conversion factors for soil', J. Environ. Radioactiv. 138, 68-71 (2014), DOI: 10.1016/j.jenvrad.2014.08.002.

  2. arXiv:0810.4656v3[math.RA]11Nov2008 THE YONEDA ALGEBRA OF A K2 ALGEBRA NEED NOT

    E-Print Network [OSTI]

    Shelton, Brad

    arXiv:0810.4656v3[math.RA]11Nov2008 THE YONEDA ALGEBRA OF A K2 ALGEBRA NEED NOT BE ANOTHER K2 ALGEBRA Thomas Cassidy, Christopher Phan and Brad Shelton Department of Mathematics Bucknell University-1222 Abstract. The Yoneda algebra of a Koszul algebra or a D-Koszul al- gebra is Koszul. K2 algebras

  3. Simultaneous Detection and Registration for Ileo-Cecal Valve Detection in 3D CT Colonography

    E-Print Network [OSTI]

    Barbu, Adrian

    Simultaneous Detection and Registration for Ileo-Cecal Valve Detection in 3D CT Colonography Le Lu1-Cecal Valve (ICV) detection in both clean and tagged 3D CT colonography scans. Our final ICV detection system

  4. AVTA Voltec AC Level 1 and Level 2 Charging Systems Testing Results...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Eaton AC Level 2 Charging System Testing Results AVTA: Aerovironment AC Level 2 Charging System Testing Results AVTA: Siemens-VersiCharge AC Level 2 Charging System Testing Results...

  5. CT Poison Control Center 2014 Video Contest Rules

    E-Print Network [OSTI]

    Kim, Duck O.

    CT Poison Control Center 2014 Video Contest Rules To Enter: 1) Record and upload a video to your an immediate family member who is an employee of the Connecticut Poison Control Center. Video Requirements: · DO NOT HANDLE, INGEST OR USE ANY ACTUAL POISONOUS OR HAZARDOUSSUBSTANCES. IF YOU HAVE QUESTIONS ABOUT

  6. Pulmonary fissure segmentation on CT Jingbin Wang a

    E-Print Network [OSTI]

    Betke, Margrit

    between the lobes in the lungs. Its segmentation is of clinical interest as it facilitates the assessment of lung disease on a lobar level. This paper describes a new approach for segmenting the major fissures in both lungs on thin-section computed tomography (CT). An image transformation called ``ridge map

  7. Status and Promise CT's and Magnetized Target Fusion

    E-Print Network [OSTI]

    . Hill (LLNL) #12;CT's: Spheromaks & Field Reversed Configurations At LLNL, the SSPX experiment is investigating spheromak formation, sustainment, and confinement issues. (Hill, Mclean, Wood, Ryutov). At UC-Davis, formation and acceleration of spheromaks. (Hwang) At the U of Washington, field reversed configuration

  8. Collapsibility of Lung Volume by Paired Inspiratory and Expiratory CT

    E-Print Network [OSTI]

    Collapsibility of Lung Volume by Paired Inspiratory and Expiratory CT Scans: Correlations with Lung Function and Mean Lung Density Tsuneo Yamashiro, MD, Shin Matsuoka, MD, PhD, Brian J. Bartholmai, MD, Rau: To evaluate the relationship between measurements of lung volume (LV) on inspiratory/expiratory computed

  9. Thoracic CT-PET Registration Using a 3D Breathing Model

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Thoracic CT-PET Registration Using a 3D Breathing Model Antonio Moreno1 , Sylvie Chambon1 , Anand P Orlando, USA Abstract. In the context of thoracic CT-PET volume registration, we present a novel method applications. We consider Computed Tomography (CT) and Positron Emission Tomography (PET) in thoracic regions

  10. Measurements from 3D-CT renderings are used in research and clinical management

    E-Print Network [OSTI]

    Vorperian, Houri K.

    Measurements from 3D-CT renderings are used in research and clinical management: · Characterization for the prism]) RENDERING TECHNIQUES USED in ANALYZE 10.0: - Volume Render - (2) Volumes of Interest 1) VOI-Auto & 2) VOI-Manual TOTAL 3D-CT MODELS: 3 mandibles X 18 CT series X 3 rendering techniques = 162 mandible

  11. Automated Tumour Delineation Using Joint PET/CT Information Vaclav Potesil 1,2

    E-Print Network [OSTI]

    Huang, Xiaolei

    Automated Tumour Delineation Using Joint PET/CT Information Vaclav Potesil 1,2 , Xiaolei Huang 1 for automated delineation of tumor boundaries in whole-body PET/CT by jointly using information from both PET. Keywords: Tumor delineation, PET-CT, segmentation, radiation therapy planning 1. INTRODUCTION

  12. Augmenting CT Cardiac Roadmaps with Segmented Streaming Qi Duan a,b

    E-Print Network [OSTI]

    Augmenting CT Cardiac Roadmaps with Segmented Streaming Ultrasound Qi Duan a,b , Guy Shechter Static X-ray computed tomography (CT) volumes are often used as anatomic roadmaps during catheter. Augmenting these static CT roadmaps with segmented myocardial borders extracted from live ultrasound (US

  13. Soft Classification with Gaussian Mixture Model for Clinical Dual-Energy CT Reconstructions

    E-Print Network [OSTI]

    1 Soft Classification with Gaussian Mixture Model for Clinical Dual-Energy CT Reconstructions, and Ken D. Sauer, Member, IEEE Abstract--We study the distribution of the clinical dual-energy CT (DECT material separation. Index Terms--Computed tomography (CT), dual energy, sta- tistical method, Gaussian

  14. The New Oncology: Cost-effectiveness and Matchless Impactof PET-CT in Cancer Management CME

    E-Print Network [OSTI]

    Jadvar, Hossein

    The New Oncology: Cost-effectiveness and Matchless Impactof PET-CT in Cancer Management CME Author in integrating cost-effective FDG-PET and PET-CT fusion techniques into their clinical armamentarium to refine the clinical impact and cost-effectiveness of advanced imaging studies such as FDG-PET scanning and PET-CT

  15. Automatic Lung Nodule Detection from Chest CT Data Using Geometrical Features: Initial Results

    E-Print Network [OSTI]

    Whelan, Paul F.

    Automatic Lung Nodule Detection from Chest CT Data Using Geometrical Features: Initial Results for automatic lung nodule detection from Chest CT data is proposed. The proposed system includes the methods of lung segmentation and nodule detection from CT data. The algorithm for lung segmentation consists

  16. Robust Segmentation of Challenging Lungs in CT using Multi-Stage Learning

    E-Print Network [OSTI]

    Robust Segmentation of Challenging Lungs in CT using Multi-Stage Learning and Level Set.Kevin Zhou1 Abstract Automatic segmentation of lung tissue in thoracic CT scans is useful for diagnosis and treatment planning of pulmonary diseases. Unlike healthy lung tissue that is easily identifiable in CT scans

  17. AC power | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch >InternshipDepartmentNeutrino-Induced1 TEMPERATUREii ABSTRACT ThisAC

  18. AVTA: Siemens-VersiCharge AC Level 2 Charging System Testing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Siemens-VersiCharge AC Level 2 Charging System Testing Results AVTA: Siemens-VersiCharge AC Level 2 Charging System Testing Results The Vehicle Technologies Office's Advanced...

  19. AVTA: GE Energy WattStation AC Level 2 Charging System Testing...

    Energy Savers [EERE]

    2012 More Documents & Publications AVTA: Aerovironment AC Level 2 Charging System Testing Results AVTA: GE Smart Grid Capable AC Level 2 Testing Results AVTA: Siemens-VersiCharge...

  20. Electrostatic coalescence system with independent AC and DC hydrophilic electrodes

    DOE Patents [OSTI]

    Hovarongkura, A. David (Arlington, VA); Henry, Jr., Joseph D. (Morgantown, WV)

    1981-01-01T23:59:59.000Z

    An improved electrostatic coalescence system is provided in which independent AC and DC hydrophilic electrodes are employed to provide more complete dehydration of an oil emulsion. The AC field is produced between an AC electrode array and the water-oil interface wherein the AC electrode array is positioned parallel to the interface which acts as a grounded electrode. The emulsion is introduced into the AC field in an evenly distributed manner at the interface. The AC field promotes drop-drop and drop-interface coalescence of the water phase in the entering emulsion. The continuous oil phase passes upward through the perforated AC electrode array and enters a strong DC field produced between closely spaced DC electrodes in which small dispersed droplets of water entrained in the continuous phase are removed primarily by collection at hydrophilic DC electrodes. Large droplets of water collected by the electrodes migrate downward through the AC electrode array to the interface. All phase separation mechanisms are utilized to accomplish more complete phase separation.

  1. business.cardiff.ac.uk Cardiff Business sChool

    E-Print Network [OSTI]

    Davies, Christopher

    business.cardiff.ac.uk Cardiff Business sChool MBa PrograMMes #12;01 business.cardiff.ac.ukWhy Cardiff Business School?01 Why Cardiff Business sChool? We are accredited by the Association to Advance Collegiate Schools of Business (AACSB International), a leading hallmark of business school excellence. We

  2. www.swansea.ac.uk/artsandhumanities Arts and Humanities

    E-Print Network [OSTI]

    Martin, Ralph R.

    dissertation or design a research project of their own (with 10,000 word report) which draws on issues Email: rhys.jones@swansea.ac.uk www.swansea.ac.uk/mediastudies/admissions - The Potter Guide to Higher relations, humanities, social science, computer science or related background. Professionals interested

  3. www.mmu.ac.uk/careers Careers & Employability Service

    E-Print Network [OSTI]

    ;www.mmu.ac.uk/careers Identifying courses · www.prospects.ac.uk/search_courses.htm · www: Courses to allow you to enter certain professions Courses that build your skills in a new area Examples · MRes (taught prep for further research) These usually involve lectures for the first two terms

  4. Personal Web Archive: E-mail: waka@iplab.cs.tsukuba.ac.jp, {shizuki,jiro}@cs.tsukuba.ac.jp

    E-Print Network [OSTI]

    Tanaka, Jiro

    Personal Web Archive: Web E-mail: waka@iplab.cs.tsukuba.ac.jp, {shizuki,jiro}@cs.tsukuba.ac.jp Web Web Web Web Web Web Personal Web Archive Personal Web Archive: Support System for Browsing the Versions of Web Page Ryota WAKAMATSU Buntarou SHIZUKI Jiro TANAKA Graduate School of Systems

  5. Safe-commutation principle for direct single-phase AC-AC converters for use in audio power

    E-Print Network [OSTI]

    and G, expressed as very low total harmonic distortion + noise (THD+N) levels and supplemented. SIngle Conversion stage AMplifier (SICAM) is the next im- portant evolutionary step in designing-stage AC-AC audio power amplifiers. As compared with the bridge commutation with load current or source

  6. Combining a Breathing Model and Tumor-Specific Rigidity Constraints for Registration of CT-PET Thoracic

    E-Print Network [OSTI]

    Chambon, Sylvie

    Combining a Breathing Model and Tumor-Specific Rigidity Constraints for Registration of CT-PET modalities, namely Computerized Tomography (CT) and Positron Emission Tomography (PET). While recent technical advancements in combined CT/PET scanners provide 3D CT and PET data of the thoracic region

  7. In-patient to isocenter KERMA ratios in CT

    SciTech Connect (OSTI)

    Huda, Walter; Ogden, Kent M.; Lavallee, Robert L.; Roskopf, Marsha L.; Scalzetti, Ernest M. [Department of Radiology and Radiological Science, Medical University of South Carolina (MUSC), 96 Jonathan Lucas Street (MSC 323), Charleston, South Carolina 29425-3230 (United States); Department of Radiology, SUNY Upstate Medical University, 750 E Adams Street, Syracuse, New York 13210 (United States)

    2011-10-15T23:59:59.000Z

    Purpose: To estimate in-patient KERMA for specific organs in computed tomography (CT) scanning using ratios to isocenter free-in-air KERMA obtained using a Rando phantom.Method: A CT scan of an anthropomorphic phantom results in an air KERMA K at a selected phantom location and air kerma K{sub CT} at the CT scanner isocenter when the scan is repeated in the absence of the phantom. The authors define the KERMA ratio (R{sub K}) as K/ K{sub CT}, which were experimentally determined in a Male Rando Phantom using lithium fluoride chips (TLD-100). R{sub K} values were obtained for a total of 400 individual point locations, as well as for 25 individual organs of interest in CT dosimetry. CT examinations of Rando were performed on a GE LightSpeed Ultra scanner operated at 80 kV, 120 kV, and 140 kV, as well as a Siemens Sensation 16 operated at 120 kV. Results: At 120 kV, median R{sub K} values for the GE and Siemens scanners were 0.60 and 0.64, respectively. The 10th percentile R{sub K} values ranged from 0.34 at 80 kV to 0.54 at 140 kV, and the 90th percentile R{sub K} values ranged from 0.64 at 80 kV to 0.78 at 140 kV. The average R{sub K} for the 25 Rando organs at 120 kV was 0.61 {+-} 0.08. Average R{sub K} values in the head, chest, and abdomen showed little variation. Relative to R{sub K} values in the head, chest, and abdomen obtained at 120 kV, R{sub K} values were about 12% lower in the pelvis and about 58% higher in the cervical spine region. Average R{sub K} values were about 6% higher on the Siemens Sensation 16 scanner than the GE LightSpeed Ultra. Reducing the x-ray tube voltage from 120 kV to 80 kV resulted in an average reduction in R{sub K} value of 34%, whereas increasing the x-ray tube voltage to 140 kV increased the average R{sub K} value by 9%. Conclusions: In-patient to isocenter relative KERMA values in Rando phantom can be used to estimate organ doses in similar sized adults undergoing CT examinations from easily measured air KERMA values at the isocenter (free in air). Conversion from in-patient air KERMA values to tissue dose would require the use of energy-appropriate conversion factors.

  8. Utilizing a simple CT dosimetry phantom for the comprehension of the operational characteristics of CT AEC systems

    SciTech Connect (OSTI)

    Tsalafoutas, Ioannis A. [Medical Physics Department, Anticancer-Oncology Hospital of Athens “Agios Savvas,” 171 Alexandras Avenue, 115 22 Athens (Greece)] [Medical Physics Department, Anticancer-Oncology Hospital of Athens “Agios Savvas,” 171 Alexandras Avenue, 115 22 Athens (Greece); Varsamidis, Athanasios; Thalassinou, Stella; Efstathopoulos, Efstathios P. [Second Department of Radiology, Medical School, University of Athens, University General Hospital, “Attikon,” Rimini 1, 124 62 Athens (Greece)] [Second Department of Radiology, Medical School, University of Athens, University General Hospital, “Attikon,” Rimini 1, 124 62 Athens (Greece)

    2013-11-15T23:59:59.000Z

    Purpose: To investigate the utility of the nested polymethylacrylate (PMMA) phantom (which is available in many CT facilities for CTDI measurements), as a tool for the presentation and comparison of the ways that two different CT automatic exposure control (AEC) systems respond to a phantom when various scan parameters and AEC protocols are modified.Methods: By offsetting the two phantom's components (the head phantom and the body ring) half-way along their longitudinal axis, a phantom with three sections of different x-ray attenuation was created. Scan projection radiographs (SPRs) and helical scans of the three-section phantom were performed on a Toshiba Aquilion 64 and a Philips Brilliance 64 CT scanners, with different scan parameter selections [scan direction, pitch factor, slice thickness, and reconstruction interval (ST/RI), AEC protocol, and tube potential used for the SPRs]. The dose length product (DLP) values of each scan were recorded and the tube current (mA) values of the reconstructed CT images were plotted against the respective Z-axis positions on the phantom. Furthermore, measurements of the noise levels at the center of each phantom section were performed to assess the impact of mA modulation on image quality.Results: The mA modulation patterns of the two CT scanners were very dissimilar. The mA variations were more pronounced for Aquilion 64, where changes in any of the aforementioned scan parameters affected both the mA modulations curves and DLP values. However, the noise levels were affected only by changes in pitch, ST/RI, and AEC protocol selections. For Brilliance 64, changes in pitch affected the mA modulation curves but not the DLP values, whereas only AEC protocol and SPR tube potential selection variations affected both the mA modulation curves and DLP values. The noise levels increased for smaller ST/RI, larger weight category AEC protocol, and larger SPR tube potential selection.Conclusions: The nested PMMA dosimetry phantom can be effectively utilized for the comprehension of CT AEC systems performance and the way that different scan conditions affect the mA modulation patterns, DLP values, and image noise. However, in depth analysis of the reasons why these two systems exhibited such different behaviors in response to the same phantom requires further investigation which is beyond the scope of this study.

  9. Upright cone beam CT imaging using the onboard imager

    SciTech Connect (OSTI)

    Fave, Xenia, E-mail: xjfave@mdanderson.org; Martin, Rachael [Department of Imaging Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 and The University of Texas Graduate School of Biomedical Sciences at Houston, Houston, Texas 77030 (United States)] [Department of Imaging Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 and The University of Texas Graduate School of Biomedical Sciences at Houston, Houston, Texas 77030 (United States); Yang, Jinzhong; Balter, Peter; Court, Laurence [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States)] [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States); Carvalho, Luis [Varian Medical Systems, Zug 6303 (Switzerland)] [Varian Medical Systems, Zug 6303 (Switzerland); Pan, Tinsu [Department of Imaging Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States)] [Department of Imaging Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States)

    2014-06-15T23:59:59.000Z

    Purpose: Many patients could benefit from being treated in an upright position. The objectives of this study were to determine whether cone beam computed tomography (CBCT) could be used to acquire upright images for treatment planning and to demonstrate whether reconstruction of upright images maintained accurate geometry and Hounsfield units (HUs). Methods: A TrueBeam linac was programmed in developer mode to take upright CBCT images. The gantry head was positioned at 0°, and the couch was rotated to 270°. The x-ray source and detector arms were extended to their lateral positions. The x-ray source and gantry remained stationary as fluoroscopic projections were taken and the couch was rotated from 270° to 90°. The x-ray tube current was normalized to deposit the same dose (measured using a calibrated Farmer ion chamber) as that received during a clinical helical CT scan to the center of a cylindrical, polyethylene phantom. To extend the field of view, two couch rotation scans were taken with the detector offset 15 cm superiorly and then 15 cm inferiorly. The images from these two scans were stitched together before reconstruction. Upright reconstructions were compared to reconstructions from simulation CT scans of the same phantoms. Two methods were investigated for correcting the HUs, including direct calibration and mapping the values from a simulation CT. Results: Overall geometry, spatial linearity, and high contrast resolution were maintained in upright reconstructions. Some artifacts were created and HU accuracy was compromised; however, these limitations could be removed by mapping the HUs from a simulation CT to the upright reconstruction for treatment planning. Conclusions: The feasibility of using the TrueBeam linac to take upright CBCT images was demonstrated. This technique is straightforward to implement and could be of enormous benefit to patients with thoracic tumors or those who find a supine position difficult to endure.

  10. HVDC-AC system interaction from AC harmonics. Volume 1. Harmonic impedance calculations. Final report

    SciTech Connect (OSTI)

    Breuer, G D; Chow, J H; Lindh, C B; Miller, N W; Numrich, F H; Price, W W; Turner, A E; Whitney, R R

    1982-09-01T23:59:59.000Z

    Improved methods are needed to characterize ac system harmonic behavior for ac filter design for HVDC systems. The purpose of this General Electric Company RP1138 research is to evaluate the present filter design practice and to investigate methods for calculating system harmonic impedances. An overview of ac filter design for HVDC systems and a survey of literature related to filter design have been performed. Two methods for calculating system harmonic impedances have been investigated. In the measurement method, an instrumentation system for measuring system voltage and current has been assembled. Different schemes of using the measurements to calculate system harmonic impedances have been studied. In the analytical method, a procedure to include various operating conditions has been proposed. Computer programs for both methods have been prepared, and the results of the measurement and analytical methods analyzed. A conclusion of the project is that the measurement and analytical methods both provided reasonable results. There are correlations between the measured and analytical results for most harmonics, although there are discrepancies between the assumptions used in the two methods. A sensitivity approach has been proposed to further correlate the results. From the results of the analysis, it is recommended that both methods should be tested further. For the measurement method, more testing should be done to cover different system operating conditions. In the analytical method, more detailed models for representing system components should be studied. In addition, alternative statistical and sensitivity approaches should be attempted.

  11. DC, AC and advanced EV propulsion systems

    SciTech Connect (OSTI)

    O'Neil, W.

    1983-08-01T23:59:59.000Z

    Battery development and liquid fuel availability and cost are still the pacing factors in wide scale electric vehicle introduction. Propulsion systems also require technical development, however, if electric vehicles are to be acceptable in the marketplace in competition against ICE vehicles. Eaton Corporation has undertaken a program designed to identify and investigate three broad types of propulsion systems in identical test vehicles on the same test track under conditions as similar as possible. Characteristics of dc, ac and advanced systems are compared to date, and projections of anticipated results and further work are provided. The compelling advantages of multiple mechanical ratios in EV propulsion systems are reviewed. An emerging, but less obvious, advantage is higher overall system efficiency.

  12. Optimal design of AC filter circuits in HVDC converter stations

    SciTech Connect (OSTI)

    Saied, M.M.; Khader, S.A. [Kuwait Univ. (Kuwait). Electrical and Computer Engineering Dept.

    1995-12-31T23:59:59.000Z

    This paper investigates the reactive power as well as the harmonic conditions on both the valve and the AC-network sides of a HVDC converter station. The effect of the AC filter circuits is accurately modeled. The program is then augmented by adding an optimization routine. It can identify the optimal filter configuration, yielding the minimum current distortion factor at the AC network terminals for a prespecified fundamental reactive power to be provided by the filter. Several parameter studies were also conducted to illustrate the effect of accidental or intentional deletion of one of the filter branches.

  13. KCP R.A'S

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:Administration SandiaAdministration News |Jordan | National

  14. Microsoft Word - Ra-15

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy ChinaofSchaeferApril 1,(EAC)TABLE OF CONTENTS 1of: U.S.5 OakNews MediaDavidRecords

  15. Application of direct pulsewidth modulation scheme to AC-DC converters: - a way to reduce ripple

    E-Print Network [OSTI]

    Zhang, Yuemin

    1993-01-01T23:59:59.000Z

    Modulation (ISPWM), 4 Direct Pulsewidth Modulation (DPWM). 15 5 Single Phase Half Controlled PWM ac-dc Converter . 6 Single Phase Full controlled PWM ac-dc Converter . 18 18 7 Simulation of SPWM ac-dc Converter. 20 8 Output Voltage Spectra of SPWM ac... 30 Balanced Three Phase Inputs 31 Output Voltage of A Three Phase Full Controlled ac-dc SPWM Converter. 42 32 Output Voltage of A Three Phase Full Controlled ac-dc EPWM Con- verter 33 Output Voltage of A Three Phase Full Controlled ac-dc ISPWM Con...

  16. Contract Number: DE-AC05-76RL01830 Modification M705

    E-Print Network [OSTI]

    #12;#12;Contract Number: DE-AC05-76RL01830 Modification M705 #12;Contract Number: DE-AC05-76RL01830 Modification M705 #12;Contract Number: DE-AC05-76RL01830 Modification M705 #12;Contract Number: DE-AC05-76RL01830 Modification M705 #12;Contract Number: DE-AC05-76RL01830 Modification M705 #12;Contract Number: DE

  17. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    are efficiency, sustainability and security of energy supplies (Euwww.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Conceptualizing Energy Security EPRG Working Paper 1123 Cambridge Working Paper in Economics 1151 Christian Winzer Energy security is one of the main

  18. A Distributed Generation Control Architecture for Islanded AC Microgrids

    E-Print Network [OSTI]

    Dominguez-Garcia, Alejandro

    1 A Distributed Generation Control Architecture for Islanded AC Microgrids Stanton T. Cady, Student architecture for generation control in islanded microgrids, and illustrate the performance Member, IEEE Abstract In this paper, we propose a distributed architecture for generation control

  19. acs news service: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    www.mmu.ac.ukcareers PG ProfessionalVocational courses: Courses to allow you to enter certain professions Courses involve lectures for the first two terms then a research...

  20. www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY

    E-Print Network [OSTI]

    Aickelin, Uwe

    www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY Contracting for wind generation EPRG to the current Renewable Obligation Certificates, ROCs, where an on-shore wind generator receives one ROC

  1. acs presspac: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 344 www.eprg.group.cam.ac.uk...

  2. ac microsized gliding: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 417 www.eprg.group.cam.ac.uk...

  3. acs evidence based: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 260 34CEN.ACS.ORG DECEMBER 23, 2013...

  4. ac surface photovoltage: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 483 www.eprg.group.cam.ac.uk...

  5. ac electrokinetic micropumps: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 477 www.eprg.group.cam.ac.uk...

  6. acs na periferia: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 388 www.eprg.group.cam.ac.uk...

  7. acute cholecystitis ac: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 384 www.eprg.group.cam.ac.uk...

  8. Cognitive Radio Network {swjang, sbahk}@netlab.snu.ac.kr

    E-Print Network [OSTI]

    Bahk, Saewoong

    2010 Cognitive Radio Network , , {swjang, sbahk}@netlab.snu.ac.kr Analysis of Average Opportunities in Cognitive Radio Networks Seowoo Jang, Saewoong Bahk INMC, EECS, Seoul National University Cognitive Radio Network . Primary user

  9. ac loss measurement: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    tape, tem- perature dependence, total ac loss, transport loss. I. INTRODUCTION HIGH 6 Heat Loss Measurement Using Infrared Imaging Texas A&M University - TxSpace Summary: in...

  10. ac linear positioning: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    USA kimik@yonsei.ac.kr Abstract- In this paper, one linear tapered slot antenna (LTSA), backed Tentzeris, Manos 187 The Square Root Law Requires a Linear Key Andrew D. Ker...

  11. November 2013 www.kent.ac.uk/library

    E-Print Network [OSTI]

    Banaji,. Murad

    November 2013 www.kent.ac.uk/library Information Services Templeman Library SCONUL Access scheme) to the Templeman Library. I am a registered member of the Sconul Access scheme and hold a valid card. If given ............................... ................................................................................................................ Home library

  12. acs morphological study: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (more) Yang, Emma Yunyi 2013-01-01 29 Study of supplementary controls for embedded HVDC links in a AC power system. Open Access Theses and Dissertations Summary: ??This...

  13. ac impedance study: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    high chromaticity. White, S 2014-01-01 37 Study of supplementary controls for embedded HVDC links in a AC power system. Open Access Theses and Dissertations Summary: ??This...

  14. Microfluidics {sjauh, btzhang}@bi.snu.ac.kr

    E-Print Network [OSTI]

    Microfluidics {sjauh, btzhang}@bi.snu.ac.kr Solving Shortest Path Problems Using Microfluidics Sahng-Joon Auh and Byoung-Tak Zhang Biointelligence Lab, School of Computer Science and Engineering Seoul National University . microfluidics MEMS

  15. ac josephson effect: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in the dc mass currents voltage, a high frequency ac voltage is applied across a superconduct- ing Josephson junction, the dc, Dm 22eV, application of a dc voltage produces...

  16. ac magnetic field: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contract No. DE-AC02-76CH00016. Abstract A common coil design concept for 2-in-1 superconduct- ing Gupta, Ramesh 126 Anisotropy of magnetic emulsions induced by magnetic and...

  17. ac magnetic fields: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contract No. DE-AC02-76CH00016. Abstract A common coil design concept for 2-in-1 superconduct- ing Gupta, Ramesh 126 Anisotropy of magnetic emulsions induced by magnetic and...

  18. www.arts.canterbury.ac.nz/internships Project Title

    E-Print Network [OSTI]

    Hickman, Mark

    , researching suppliers and material requirements. The intern will also do research about.arts.canterbury.ac.nz/internships Necessary Qualifications: Major/Minors(s): All majors in the B.A. especially those interested in media

  19. Strongly nonlinear dynamics of electrolytes in large ac voltages

    E-Print Network [OSTI]

    Hojgaard Olesen, Laurits

    We study the response of a model microelectrochemical cell to a large ac voltage of frequency comparable to the inverse cell relaxation time. To bring out the basic physics, we consider the simplest possible model of a ...

  20. Adjustable Speed AC Motor Drives-Applications Problems

    E-Print Network [OSTI]

    Enjeti, P.

    Adjustable Speed AC Motor Drives Applications Problems by Dr. P. Enjeti Power Quality Laboratory Department ofElectrical Engineering Texas A&M University College Station, TX 77843 Tel: 409-845-7466 Fax: 409-845-6259 Email..., it generates side effects, some which have been recognized only recently. This paper presents a comprehensive coverage of application issues of PWM inverter controlled ac motor drives which include damage to motor insulation due to reflected voltages caused...

  1. Development of an AC Module System: Final Technical Report

    SciTech Connect (OSTI)

    Suparna Kadam; Miles Russell

    2012-06-15T23:59:59.000Z

    The GreenRay Inc. program focused on simplifying solar electricity and making it affordable and accessible to the mainstream population. This was accomplished by integrating a solar module, micro-inverter, mounting and monitoring into a reliable, 'plug and play' AC system for residential rooftops, offering the following advantages: (1) Reduced Cost: Reduction in installation labor with fewer components, faster mounting, faster wiring. (2) Maximized Energy Production: Each AC Module operates at its maximum, reducing overall losses from shading, mismatch, or module downtime. (3) Increased Safety. Electrical and fire safety experts agree that AC Modules have significant benefits, with no energized wiring or live connections during installation, maintenance or emergency conditions. (4) Simplified PV for a Broader Group of Installers. Dramatic simplification of design and installation of a solar power system, enabling faster and more efficient delivery of the product into the market through well-established, mainstream channels. This makes solar more accessible to the public. (5) Broadened the Rooftop Market: AC Modules enable solar for many homes that have shading, split roofs, or obstructions. In addition, due to the smaller building block size of 200W vs. 1000W, homeowners with budget limitations can start small and add to their systems over time. Through this DOE program GreenRay developed the all-in-one AC Module system with an integrated PV Module and microinverter, custom residential mounting and performance monitoring. Development efforts took the product from its initial concept, through prototypes, to a commercial product sold and deployed in the residential market. This pilot deployment has demonstrated the technical effectiveness of the AC Module system in meeting the needs and solving the problems of the residential market. While more expensive than the traditional central inverter systems at the pilot scale, the economics of AC Modules become more and more favorable as the product matures and is made in high volumes. GreenRay's early customers have been highly enthusiastic about the AC Module system benefits.

  2. http://www-cr.scphys.kyoto-u.ac.jp/gakubu/P6.html http://www-cr.scphys.kyoto-u.ac.jp/gakubu/P6.html

    E-Print Network [OSTI]

    2011 P6 http://www-cr.scphys.kyoto-u.ac.jp/gakubu/P6.html web #12;http://www-cr.scphys.kyoto-u.ac.jp/gakubu/P6.html () ( #12;http://www-cr.scphys.kyoto-u.ac.jp/gakubu/P6.html X MeV X Astro-H 2013 TeV10m) #12;http://www-cr.scphys.kyoto-u.ac.jp/gakubu/P6.html 2010 ASTRO-H CCD X (2) () (2) (2

  3. Dedicated breast CT: Fibroglandular volume measurements in a diagnostic population

    SciTech Connect (OSTI)

    Vedantham, Srinivasan; Shi Linxi; Karellas, Andrew; O'Connell, Avice M. [Department of Radiology, University of Massachusetts Medical School, Worcester, Massachusetts 01655 (United States); Department of Imaging Sciences, University of Rochester Medical Center, Rochester, New York 14642 (United States)

    2012-12-15T23:59:59.000Z

    Purpose: To determine the mean and range of volumetric glandular fraction (VGF) of the breast in a diagnostic population using a high-resolution flat-panel cone-beam dedicated breast CT system. This information is important for Monte Carlo-based estimation of normalized glandular dose coefficients and for investigating the dependence of VGF on breast dimensions, race, and pathology. Methods: Image data from a clinical trial investigating the role of dedicated breast CT that enrolled 150 women were retrospectively analyzed to determine the VGF. The study was conducted in adherence to a protocol approved by the institutional human subjects review boards and written informed consent was obtained from all study participants. All participants in the study were assigned BI-RADS{sup Registered-Sign} 4 or 5 as per the American College of Radiology assessment categories after standard diagnostic work-up and underwent dedicated breast CT exam prior to biopsy. A Gaussian-kernel based fuzzy c-means algorithm was used to partition the breast CT images into adipose and fibroglandular tissue after segmenting the skin. Upon determination of the accuracy of the algorithm with a phantom, it was applied to 137 breast CT volumes from 136 women. VGF was determined for each breast and the mean and range were determined. Pathology results with classification as benign, malignant, and hyperplasia were available for 132 women, and were used to investigate if the distributions of VGF varied with pathology. Results: The algorithm was accurate to within {+-}1.9% in determining the volume of an irregular shaped phantom. The study mean ({+-} inter-breast SD) for the VGF was 0.172 {+-} 0.142 (range: 0.012-0.719). VGF was found to be negatively correlated with age, breast dimensions (chest-wall to nipple length, pectoralis to nipple length, and effective diameter at chest-wall), and total breast volume, and positively correlated with fibroglandular volume. Based on pathology, pairwise statistical analysis (Mann-Whitney test) indicated that at the 0.05 significance level, there was no significant difference in distributions of VGF without adjustment for age between malignant and nonmalignant breasts (p= 0.41). Pairwise comparisons of the distributions of VGF in increasing order of mammographic breast density indicated all comparisons were statistically significant (p < 0.002). Conclusions: This study used a different clinical prototype breast CT system than that in previous studies to image subjects from a different geographical region, and used a different algorithm for analysis of image data. The mean VGF estimated from this study is within the range reported in previous studies, indicating that the choice of 50% glandular weight fraction to represent an average breast for Monte Carlo-based estimation of normalized glandular dose coefficients in mammography needs revising. In the study, the distributions of VGF did not differ significantly with pathology.

  4. Embedded Library in WebCT: Pushing UCSD Library Resources to Faculty Courses

    E-Print Network [OSTI]

    Ho, SuHui

    2007-01-01T23:59:59.000Z

    keeper about pushing the library to department pages & webEmbedded Library in WebCT:Pushing UCSD Library Resources to Faculty Courses Presenter:

  5. A Fossilized Opal A To Opal C-T Transformation On The Northeast...

    Open Energy Info (EERE)

    Fossilized Opal A To Opal C-T Transformation On The Northeast Atlantic Margin- Support For A Significantly Elevated Palaeogeothermal Gradient During The Neogene? Jump to:...

  6. CT Scans of Cores Metadata, Barrow, Alaska 2015

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Katie McKnight; Tim Kneafsey; Craig Ulrich

    Individual ice cores were collected from Barrow Environmental Observatory in Barrow, Alaska, throughout 2013 and 2014. Cores were drilled along different transects to sample polygonal features (i.e. the trough, center and rim of high, transitional and low center polygons). Most cores were drilled around 1 meter in depth and a few deep cores were drilled around 3 meters in depth. Three-dimensional images of the frozen cores were constructed using a medical X-ray computed tomography (CT) scanner. TIFF files can be uploaded to ImageJ (an open-source imaging software) to examine soil structure and densities within each core.

  7. Towards local progression estimation of pulmonary emphysema using CT

    SciTech Connect (OSTI)

    Staring, M., E-mail: m.staring@lumc.nl; Bakker, M. E.; Shamonin, D. P.; Reiber, J. H. C.; Stoel, B. C. [Department of Radiology, Division of Image Processing, Leiden University Medical Center, PO Box 9600, 2300 RC Leiden (Netherlands)] [Department of Radiology, Division of Image Processing, Leiden University Medical Center, PO Box 9600, 2300 RC Leiden (Netherlands); Stolk, J. [Department of Pulmonology, Leiden University Medical Center, PO Box 9600, 2300 RC Leiden (Netherlands)] [Department of Pulmonology, Leiden University Medical Center, PO Box 9600, 2300 RC Leiden (Netherlands)

    2014-02-15T23:59:59.000Z

    Purpose: Whole lung densitometry on chest CT images is an accepted method for measuring tissue destruction in patients with pulmonary emphysema in clinical trials. Progression measurement is required for evaluation of change in health condition and the effect of drug treatment. Information about the location of emphysema progression within the lung may be important for the correct interpretation of drug efficacy, or for determining a treatment plan. The purpose of this study is therefore to develop and validate methods that enable the local measurement of lung density changes, which requires proper modeling of the effect of respiration on density. Methods: Four methods, all based on registration of baseline and follow-up chest CT scans, are compared. The first naïve method subtracts registered images. The second employs the so-called dry sponge model, where volume correction is performed using the determinant of the Jacobian of the transformation. The third and the fourth introduce a novel adaptation of the dry sponge model that circumvents its constant-mass assumption, which is shown to be invalid. The latter two methods require a third CT scan at a different inspiration level to estimate the patient-specific density-volume slope, where one method employs a global and the other a local slope. The methods were validated on CT scans of a phantom mimicking the lung, where mass and volume could be controlled. In addition, validation was performed on data of 21 patients with pulmonary emphysema. Results: The image registration method was optimized leaving a registration error below half the slice increment (median 1.0 mm). The phantom study showed that the locally adapted slope model most accurately measured local progression. The systematic error in estimating progression, as measured on the phantom data, was below 2 gr/l for a 70 ml (6%) volume difference, and 5 gr/l for a 210 ml (19%) difference, if volume correction was applied. On the patient data an underlying linearity assumption relating lung volume change with density change was shown to hold (fitR{sup 2} = 0.94), and globalized versions of the local models are consistent with global results (R{sup 2} of 0.865 and 0.882 for the two adapted slope models, respectively). Conclusions: In conclusion, image matching and subsequent analysis of differences according to the proposed lung models (i) has good local registration accuracy on patient data, (ii) effectively eliminates a dependency on inspiration level at acquisition time, (iii) accurately predicts progression in phantom data, and (iv) is reasonably consistent with global results in patient data. It is therefore a potential future tool for assessing local emphysema progression in drug evaluation trials and in clinical practice.

  8. DOE - Office of Legacy Management -- New Canaan Site - CT 08

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp - CT 0-01Naturita36 SupplyCanaan Site -

  9. System and method for determining stator winding resistance in an AC motor using motor drives

    DOE Patents [OSTI]

    Lu, Bin; Habetler, Thomas G; Zhang, Pinjia

    2013-02-26T23:59:59.000Z

    A system and method for determining the stator winding resistance of AC motors is provided. The system includes an AC motor drive having an input connectable to an AC source and an output connectable to an input terminal of an AC motor, a pulse width modulation (PWM) converter having switches therein to control current flow and terminal voltages in the AC motor, and a control system connected to the PWM converter. The control system generates a command signal to cause the PWM converter to control an output of the AC motor drive corresponding to an input to the AC motor, selectively generates a modified command signal to cause the PWM converter to inject a DC signal into the output of the AC motor drive, and determines a stator winding resistance of the AC motor based on the DC signal of at least one of the voltage and current.

  10. Simultaneous CT and SPECT tomography using CZT detectors

    DOE Patents [OSTI]

    Paulus, Michael J. (Knoxville, TN); Sari-Sarraf, Hamed (Lubbock, TX); Simpson, Michael L. (Knoxville, TN); Britton, Jr., Charles L. (Alcoa, TN)

    2002-01-01T23:59:59.000Z

    A method for simultaneous transmission x-ray computed tomography (CT) and single photon emission tomography (SPECT) comprises the steps of: injecting a subject with a tracer compound tagged with a .gamma.-ray emitting nuclide; directing an x-ray source toward the subject; rotating the x-ray source around the subject; emitting x-rays during the rotating step; rotating a cadmium zinc telluride (CZT) two-sided detector on an opposite side of the subject from the source; simultaneously detecting the position and energy of each pulsed x-ray and each emitted .gamma.-ray captured by the CZT detector; recording data for each position and each energy of each the captured x-ray and .gamma.-ray; and, creating CT and SPECT images from the recorded data. The transmitted energy levels of the x-rays lower are biased lower than energy levels of the .gamma.-rays. The x-ray source is operated in a continuous mode. The method can be implemented at ambient temperatures.

  11. DE-AC05-00OR22725 Section B--Page 1 of 7 DE-AC05-00OR22725

    E-Print Network [OSTI]

    .......................................................................... 5 #12;DE-AC05-00OR22725 Section B--Page 2 of 7 DE-AC05-000R22725 Modification No. 760 Section B Blank Page #12;DE-AC05-00OR22725 Section B--Page 3 of 7 DE-AC05-000R22725 Modification No. 760 Section B of 7 DE-AC05-000R22725 Modification No. 760 Section B 4) $267,518 for the project entitled "4500 Area

  12. Effects of the difference in tube voltage of the CT scanner on dose calculation

    E-Print Network [OSTI]

    Rhee, Dong Joo; Moon, Young Min; Kim, Jung Ki; Jeong, Dong Hyeok

    2015-01-01T23:59:59.000Z

    Computed Tomography (CT) measures the attenuation coefficient of an object and converts the value assigned to each voxel into a CT number. In radiation therapy, CT number, which is directly proportional to the linear attenuation coefficient, is required to be converted to electron density for radiation dose calculation for cancer treatment. However, if various tube voltages were applied to take the patient CT image without applying the specific CT number to electron density conversion curve, the accuracy of dose calculation would be unassured. In this study, changes in CT numbers for different materials due to change in tube voltage were demonstrated and the dose calculation errors in percentage depth dose (PDD) and a clinical case were analyzed. The maximum dose difference in PDD from TPS dose calculation and Monte Carlo simulation were 1.3 % and 1.1 % respectively when applying the same CT number to electron density conversion curve to the 80 kVp and 140 kVp images. In the clinical case, the different CT nu...

  13. CT-PET Landmark-based Lung Registration Using a Dynamic Breathing Model S. Chambon1

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    CT-PET Landmark-based Lung Registration Using a Dynamic Breathing Model S. Chambon1 , A. Moreno1-based registration of CT (at two different instants of the breathing cycle, intermediate expirations) and PET images in order to simulate the instant in the breathing cycle most similar to the PET image and guarantee

  14. SPECIAL REPORTS AND REVIEWS Mass Screening With CT Colonography: Should the Radiation

    E-Print Network [OSTI]

    Brenner, David Jonathan

    SPECIAL REPORTS AND REVIEWS Mass Screening With CT Colonography: Should the Radiation Exposure is highly advantageous, it can be performed with lower radiation doses than almost any other CT examination market in the United States would soon be over 100 million people. Therefore, it is pertinent to consider

  15. Siemens AG, CT IC 4, H.-G. Zimmermann1 CORPORATETECHNOLOGY

    E-Print Network [OSTI]

    Schmidhuber, Juergen

    © Siemens AG, CT IC 4, H.-G. Zimmermann1 CORPORATETECHNOLOGY System Identification & Forecasting with Advanced Neural Networks Principles, Techniques, Applications Hans Georg Zimmermann Siemens AG Email : Hans_Georg.Zimmermann@siemens.com © Siemens AG, CT IC 4, H.-G. Zimmermann2 CORPORATETECHNOLOGY . . . . ! " i ii wxw 0 w1 wn xn x1 Distinct

  16. Bone Surface Reconstruction From CT/MR Images Using Fast Marching and Level Set Methods1)

    E-Print Network [OSTI]

    Chetverikov, Dmitry

    Bone Surface Reconstruction From CT/MR Images Using Fast Marching and Level Set Methods1) Istv surfaces reconstructed from MR volumes are shown. 1 Outline of the project One of our current projects steps of bone surface reconstruction from CT/MR slice images. 2 Main steps of reconstruction 2.1

  17. A Model-Based Iterative Algorithm for Dual-Energy X-Ray CT Reconstruction

    E-Print Network [OSTI]

    A Model-Based Iterative Algorithm for Dual-Energy X-Ray CT Reconstruction Ruoqiao Zhang, Jean, Senior Member, IEEE Abstract--Recent developments in dual-energy X-ray CT have shown a number of benefits the opportunity to reduce noise and artifacts in dual energy reconstructions. However, previous approaches

  18. Multi-Material Decomposition Using Statistical Image Reconstruction in X-Ray CT

    E-Print Network [OSTI]

    Fessler, Jeffrey A.

    and Jeffrey A. Fessler Abstract--Dual-energy (DE) CT scans provide two sets of measurements at two different-mean-square (RMS) errors. Index Terms--Computed tomography, dual energy, multi- material decomposition, statistical image reconstruction I. INTRODUCTION Dual-energy (DE) CT reconstruction methods typically re- construct

  19. Hemorrhage Slices Detection in Brain CT Images Ruizhe Liu, Chew Lim Tan, Tze Yun Leong

    E-Print Network [OSTI]

    Tan, Chew Lim

    Hemorrhage Slices Detection in Brain CT Images Ruizhe Liu, Chew Lim Tan, Tze Yun Leong Department) scans are widely used in today's diagnosis of head traumas. It is effective to disclose the bleeding Tomography (CT) scans are widely used in today's diagnosis of head traumas. It is effective to disclose

  20. AUTOMATIC HEART ISOLATION FOR CT CORONARY VISUALIZATION USING G. Funka-Lea1

    E-Print Network [OSTI]

    Boykov, Yuri

    AUTOMATIC HEART ISOLATION FOR CT CORONARY VISUALIZATION USING GRAPH-CUTS G. Funka-Lea1 , Y. Boykov3 isolate the outer surface of the entire heart in Computer Tomogra- phy (CT) cardiac scans. Isolating the entire heart allows the coronary vessels on the surface of the heart to be easily visu- alized despite

  1. Non-Destructive Whole Lung Assessment via Multi-scale Micro CT Imaging Combined with Stereology

    E-Print Network [OSTI]

    Wang, Ge

    Non-Destructive Whole Lung Assessment via Multi-scale Micro CT Imaging Combined with Stereology Tech, Virginia, USA Running head Non-Destructive Whole Lung Assessment via µCT Contact Information Eric-hoffman@uiowa.edu Phone: 319-353-6213 Fax: 319-356-1503 #12;Abstract Estimating volume fractions of the lung parenchyma

  2. Location registration and recognition (LRR) for serial analysis of nodules in lung CT scans

    E-Print Network [OSTI]

    Location registration and recognition (LRR) for serial analysis of nodules in lung CT scans Michal t In the clinical workflow for lung cancer management, the comparison of nodules between CT scans from subsequent in investigating the condition of the lung. The algorithm uses a combination of feature extraction, indexing

  3. ROBUST SEGMENTATION OF LUNG TISSUE IN CHEST CT SCANNING Amal Farag, James Graham and Aly Farag

    E-Print Network [OSTI]

    Louisville, University of

    ROBUST SEGMENTATION OF LUNG TISSUE IN CHEST CT SCANNING Amal Farag, James Graham and Aly Farag.edu ABSTRACT This paper deals with segmentation of the lung tissues from low dose CT (LDCT) scans of the chest. Goal is correct segmentation as well as maintaining the details of the lung region in the chest cavity

  4. Automated segmentation of lungs with severe interstitial lung disease in CT

    E-Print Network [OSTI]

    Automated segmentation of lungs with severe interstitial lung disease in CT Jiahui Wang Department: Accurate segmentation of lungs with severe interstitial lung disease ILD in thoracic computed tomography CT developed in this study a texture analysis-based method for accurate segmentation of lungs with severe ILD

  5. AC Loss Measurements on a 2G YBCO Coil

    SciTech Connect (OSTI)

    Rey, Christopher M [ORNL] [ORNL; Duckworth, Robert C [ORNL] [ORNL; Schwenterly, S W [ORNL] [ORNL

    2011-01-01T23:59:59.000Z

    The Oak Ridge National Laboratory (ORNL) is collaborating with Waukesha Electric Systems (WES) to continue development of HTS power transformers. For compatibility with the existing power grid, a commercially viable HTS transformer will have to operate at high voltages in the range of 138 kV and above, and will have to withstand 550-kV impulse voltages as well. Second-generation (2G) YBCO coated conductors will be required for an economically-competitive design. In order to adequately size the refrigeration system for these transformers, the ac loss of these HTS coils must be characterized. Electrical AC loss measurements were conducted on a prototype high voltage (HV) coil with co-wound stainless steel at 60 Hz in a liquid nitrogen bath using a lock-in amplifier technique. The prototype HV coil consisted of 26 continuous (without splice) single pancake coils concentrically centered on a stainless steel former. For ac loss measurement purposes, voltage tap pairs were soldered across each set of two single pancake coils so that a total of 13 separate voltage measurements could be made across the entire length of the coil. AC loss measurements were taken as a function of ac excitation current. Results show that the loss is primarily concentrated at the ends of the coil where the operating fraction of critical current is the highest and show a distinct difference in current scaling of the losses between low current and high current regimes.

  6. CT-FIRE (V1.3 Beta2) User's Manual, LOCI @ UW-Madison CT-FIRE V1.3 Beta2 User's Manual (November 6 2014)

    E-Print Network [OSTI]

    Yavuz, Deniz

    CT-FIRE (V1.3 Beta2) User's Manual, LOCI @ UW-Madison 1 CT-FIRE V1.3 Beta2 User's Manual (November straightness. Using #12;CT-FIRE (V1.3 Beta2) User's Manual, LOCI @ UW-Madison 2 the advanced output control-processing. Major features of the versions Version 1.3 Beta2 (newest): The primary change in CT-FIRE V1.3 Beta2

  7. Superconducting shielded core reactor with reduced AC losses

    DOE Patents [OSTI]

    Cha, Yung S.; Hull, John R.

    2006-04-04T23:59:59.000Z

    A superconducting shielded core reactor (SSCR) operates as a passive device for limiting excessive AC current in a circuit operating at a high power level under a fault condition such as shorting. The SSCR includes a ferromagnetic core which may be either closed or open (with an air gap) and extends into and through a superconducting tube or superconducting rings arranged in a stacked array. First and second series connected copper coils each disposed about a portion of the iron core are connected to the circuit to be protected and are respectively wound inside and outside of the superconducting tube or rings. A large impedance is inserted into the circuit by the core when the shielding capability of the superconducting arrangement is exceeded by the applied magnetic field generated by the two coils under a fault condition to limit the AC current in the circuit. The proposed SSCR also affords reduced AC loss compared to conventional SSCRs under continuous normal operation.

  8. Vertical Profiles Of {sup 226}Ra, {sup 232}Th And {sup 40}K Activities In Rocks From The Irati Formation Of The Parana Sedimentary Basin, Southern Brazil

    SciTech Connect (OSTI)

    Ferreira, Ademar de O.; Bastos, Rodrigo O.; Appoloni, Carlos R. [Laboratorio de Fisica Nuclear Aplicada-Departamento de Fisica-CCE Universidade Estadual de Londrina-Campus Universitario Rodovia Celso Garcia Cid s/n, Cx. Postal 6001 86051-990 Londrina (Puerto Rico)

    2008-08-07T23:59:59.000Z

    Naturally occurring radioisotopes are present in different concentrations in sedimentary rocks, reflecting the origin of the sediments, the depositional environment, and more recent events such as weathering and erosion. Using a high-resolution {gamma}-ray spectrometry methodology, sedimentary rocks were measured to assess the concentration activities of the natural radioisotopes. The surveyed rocks are from the Irati formation in the Parana sedimentary basin, which are exposed by an abandoned, open-pit limestone mine, in the city of Sapopema, southern Brazil. The exposed vertical profile is 5 m, and its stratigraphy is represented by an alternation of limestone and bituminous shale (layers being a few decimeters thick), and some millimeter rhythm layers with limestone and bituminous shale laminas. Eleven samples were collected along this profile, each of them dried in the open air during 48 hours, sieved through 4 mm mesh and sealed in cylindrical recipients. Measurements were accomplished using a 66% relative efficiency HPGE detector connected to a standard gamma ray spectrometry electronic chain. The detector efficiency in the range of 60 to 1800 keV was carried out with the certified IAEA-385 sediment sample. The Lower Limit of Detection (LLD) to the system is 2.40 Bq{center_dot}kg{sup -1} for {sup 226}Ra, 1.84 Bq{center_dot}kg{sup -1} for {sup 232}Th and 4.20 Bq{center_dot}kg{sup -1} for {sup 40}K. Activity concentrations were determined for {sup 226}Ra (from 16.22 to 151.55 Bq{center_dot}kg{sup -1}), {sup 232}Th (from 2.93 to 56.12 Bq{center_dot}kg{sup -1}) and {sup 40}K (from 38.45 to 644.63 Bq{center_dot}kg{sup -1}). The layers enriched with organic matter presented the higher values of activity. The measured concentrations of the natural radioisotopes were lower for limestone samples (average values and respective deviations were 22.81{+-}0.22 Bq{center_dot}kg{sup -1} for {sup 226}Ra, 4.21{+-}0.07 Bq{center_dot}kg{sup -1} for {sup 232}Th, and 50.11{+-}0.82 Bq{center_dot}kg{sup -1} for {sup 40}K). Higher concentrations were measured for the bituminous shale samples (average values and respective deviations were 108.10{+-}12.17 Bq{center_dot}kg{sup -1} for {sup 226}Ra, 43.69{+-}0.30 Bq{center_dot}kg{sup -1} for {sup 232}Th, and 465.82{+-}3.99 Bq{center_dot}kg{sup -1} for {sup 40}K). The concentrations were intermediate for the rhythmite samples (average values and respective deviations were 50.69{+-}1.09 Bq{center_dot}kg{sup -1} for {sup 226}Ra, 7.63{+-}0.21 Bq{center_dot}kg{sup -1} for {sup 232}Th, and 85.96{+-}2.47 Bq{center_dot}kg{sup -1} for {sup 40}K). As the analyzed rocks are raw materials for the ceramic, cement and soil correction compound industries, the results of this work furnish data to estimate the contribution of these products to the general public's radiation exposure.

  9. List of Participants Brian Baptie British Geological Survey bbap@bgs.ac.uk

    E-Print Network [OSTI]

    .ac.uk Nicola D'Agostino Istituto Nazionale Geofisica Vulcanologia dagostin@ingv.it Serena Davies 360 Production@bgs.ac.uk Guilio Selvaggi Istituto Nazionale Geofisica Vulcanologia selvaggi@ingv.it Alistair Sloan Earth Sciences

  10. DE-AC02-76SF00515 Apr2007/Rev 1

    E-Print Network [OSTI]

    Wechsler, Risa H.

    DE-AC02-76SF00515 Appendix B Apr2007/Rev 1 FY 2007 Contractor Performance Evaluation and Measurement Plan for Management and Operations ofthe Stanford Linear Accelerator Center J-B-i #12;DE-AC02

  11. Pulmonary Vascular Tree Segmentation from Contrast-Enhanced CT Images

    E-Print Network [OSTI]

    Helmberger, M; Pienn, M; Balint, Z; Olschewski, A; Bischof, H

    2013-01-01T23:59:59.000Z

    We present a pulmonary vessel segmentation algorithm, which is fast, fully automatic and robust. It uses a coarse segmentation of the airway tree and a left and right lung labeled volume to restrict a vessel enhancement filter, based on an offset medialness function, to the lungs. We show the application of our algorithm on contrast-enhanced CT images, where we derive a clinical parameter to detect pulmonary hypertension (PH) in patients. Results on a dataset of 24 patients show that quantitative indices derived from the segmentation are applicable to distinguish patients with and without PH. Further work-in-progress results are shown on the VESSEL12 challenge dataset, which is composed of non-contrast-enhanced scans, where we range in the midfield of participating contestants.

  12. Monitoring internal organ motion with continuous wave radar in CT

    SciTech Connect (OSTI)

    Pfanner, Florian [Institute of Medical Physics, University of Erlangen–Nürnberg, 91052 Erlangen, Germany and Siemens AG, Healthcare Sector, Siemensstr. 1, 91301 Forchheim (Germany)] [Institute of Medical Physics, University of Erlangen–Nürnberg, 91052 Erlangen, Germany and Siemens AG, Healthcare Sector, Siemensstr. 1, 91301 Forchheim (Germany); Maier, Joscha [Medical Physics in Radiology, German Cancer Research Center (DKFZ), Im Neuenheimer Feld 280, 69120 Heidelberg (Germany)] [Medical Physics in Radiology, German Cancer Research Center (DKFZ), Im Neuenheimer Feld 280, 69120 Heidelberg (Germany); Allmendinger, Thomas; Flohr, Thomas [Siemens AG, Healthcare Sector, Siemensstr. 1, 91301 Forchheim (Germany)] [Siemens AG, Healthcare Sector, Siemensstr. 1, 91301 Forchheim (Germany); Kachelrieß, Marc [Institute of Medical Physics, University of Erlangen–Nürnberg, 91052 Erlangen, Germany and Medical Physics in Radiology, German Cancer Research Center (DKFZ), Im Neuenheimer Feld 280, 69120 Heidelberg (Germany)] [Institute of Medical Physics, University of Erlangen–Nürnberg, 91052 Erlangen, Germany and Medical Physics in Radiology, German Cancer Research Center (DKFZ), Im Neuenheimer Feld 280, 69120 Heidelberg (Germany)

    2013-09-15T23:59:59.000Z

    Purpose: To avoid motion artifacts in medical imaging or to minimize the exposure of healthy tissues in radiation therapy, medical devices are often synchronized with the patient's respiratory motion. Today's respiratory motion monitors require additional effort to prepare the patients, e.g., mounting a motion belt or placing an optical reflector on the patient's breast. Furthermore, they are not able to measure internal organ motion without implanting markers. An interesting alternative to assess the patient's organ motion is continuous wave radar. The aim of this work is to design, implement, and evaluate such a radar system focusing on application in CT.Methods: The authors designed a radar system operating in the 860 MHz band to monitor the patient motion. In the intended application of the radar system, the antennas are located close to the patient's body inside the table of a CT system. One receive and four transmitting antennas are used to avoid the requirement of exact patient positioning. The radar waves propagate into the patient's body and are reflected at tissue boundaries, for example at the borderline between muscle and adipose tissue, or at the boundaries of organs. At present, the authors focus on the detection of respiratory motion. The radar system consists of the hardware mentioned above as well as of dedicated signal processing software to extract the desired information from the radar signal. The system was evaluated using simulations and measurements. To simulate the radar system, a simulation model based on radar and wave field equations was designed and 4D respiratory-gated CT data sets were used as input. The simulated radar signals and the measured data were processed in the same way. The radar system hardware and the signal processing algorithms were tested with data from ten volunteers. As a reference, the respiratory motion signal was recorded using a breast belt simultaneously with the radar measurements.Results: Concerning the measurements of the test persons, there is a very good correlation (?= 0.917) between the respiratory motion phases received by the radar system and the external motion monitor. Our concept of using an array of transmitting antennas turned out to be widely insensitive to the positioning of the test persons. A time shift between the respiratory motion curves recorded with the radar system and the motion curves from the external respiratory monitor was observed which indicates a slight difference between internal organ motion and motion detected by the external respiratory monitor. The simulations were in good accordance with the measurements.Conclusions: A continuous wave radar operating in the near field of the antennas can be used to determine the respiratory motion of humans accurately. In contrast to trigger systems used today, the radar system is able to measure motion inside the body. If such a monitor was routinely available in clinical CT, it would be possible optimizing the scan start with respect to the respiratory state of the patient. Breathing commands would potentially widely be avoided, and as far as uncooperative patients or children are concerned, less sedation might be necessary. Further applications of the radar system could be in radiation therapy or interventional imaging for instance.

  13. Investigation of statistical iterative reconstruction for dedicated breast CT

    SciTech Connect (OSTI)

    Makeev, Andrey; Glick, Stephen J. [UMass Medical School, 55 Lake Avenue North, Worcester, Massachusetts 01655 (United States)] [UMass Medical School, 55 Lake Avenue North, Worcester, Massachusetts 01655 (United States)

    2013-08-15T23:59:59.000Z

    Purpose: Dedicated breast CT has great potential for improving the detection and diagnosis of breast cancer. Statistical iterative reconstruction (SIR) in dedicated breast CT is a promising alternative to traditional filtered backprojection (FBP). One of the difficulties in using SIR is the presence of free parameters in the algorithm that control the appearance of the resulting image. These parameters require tuning in order to achieve high quality reconstructions. In this study, the authors investigated the penalized maximum likelihood (PML) method with two commonly used types of roughness penalty functions: hyperbolic potential and anisotropic total variation (TV) norm. Reconstructed images were compared with images obtained using standard FBP. Optimal parameters for PML with the hyperbolic prior are reported for the task of detecting microcalcifications embedded in breast tissue.Methods: Computer simulations were used to acquire projections in a half-cone beam geometry. The modeled setup describes a realistic breast CT benchtop system, with an x-ray spectra produced by a point source and an a-Si, CsI:Tl flat-panel detector. A voxelized anthropomorphic breast phantom with 280 ?m microcalcification spheres embedded in it was used to model attenuation properties of the uncompressed woman's breast in a pendant position. The reconstruction of 3D images was performed using the separable paraboloidal surrogates algorithm with ordered subsets. Task performance was assessed with the ideal observer detectability index to determine optimal PML parameters.Results: The authors' findings suggest that there is a preferred range of values of the roughness penalty weight and the edge preservation threshold in the penalized objective function with the hyperbolic potential, which resulted in low noise images with high contrast microcalcifications preserved. In terms of numerical observer detectability index, the PML method with optimal parameters yielded substantially improved performance (by a factor of greater than 10) compared to FBP. The hyperbolic prior was also observed to be superior to the TV norm. A few of the best-performing parameter pairs for the PML method also demonstrated superior performance for various radiation doses. In fact, using PML with certain parameter values results in better images, acquired using 2 mGy dose, than FBP-reconstructed images acquired using 6 mGy dose.Conclusions: A range of optimal free parameters for the PML algorithm with hyperbolic and TV norm-based potentials is presented for the microcalcification detection task, in dedicated breast CT. The reported values can be used as starting values of the free parameters, when SIR techniques are used for image reconstruction. Significant improvement in image quality can be achieved by using PML with optimal combination of parameters, as compared to FBP. Importantly, these results suggest improved detection of microcalcifications can be obtained by using PML with lower radiation dose to the patient, than using FBP with higher dose.

  14. Computational analysis of whole body CT documents a bone structure alteration in adult advanced chronic lymphocytic leukemia

    E-Print Network [OSTI]

    Piana, Michele

    progression. PET/CT images were analyzed using dedicated software, able to recognize an external 2-pixel bone ring whose Hounsfield coefficient served as cut off to recognize trabecular and compact bone. PET/CT of the disease. Keywords: Image Analysis, Bone Marrow, Skeletal Structure, ACLL, PET/CT #12;3 Introduction

  15. Measuring the whole bone marrow asset in humans by a computational approach to integrated PET/CT imaging.

    E-Print Network [OSTI]

    Piana, Michele

    ; 7 CNR-SPIN. Genova. Italy Running Head: PET/CT measurement of bone marrow volume AddressMeasuring the whole bone marrow asset in humans by a computational approach to integrated PET/CT to chemotherapy. Keywords: PET/CT; bone marrow imaging; image processing. #12;2 Introduction Bone marrow (BM

  16. Dual energy CT-based characterization of x-ray attenuation properties of breast equivalent material plates

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Dual energy CT-based characterization of x-ray attenuation properties of breast equivalent material of the same nominal breast density equivalence (+ 1.5 HU). In addition, dual energy CT provided mono equivalent material, breast density, attenuation properties, linear attenuation coefficients, dual energy CT

  17. Statistical analysis of Multi-Material Components using Dual Energy CT Christoph Heinzl, Johann Kastner, Torsten Moller, and Eduard Groller

    E-Print Network [OSTI]

    Statistical analysis of Multi-Material Components using Dual Energy CT Christoph Heinzl, Johann plastics-metal components. The presented work makes use of dual energy CT data acquisi- tion for artefact pipeline based on the dual ex- posure technique of dual energy CT. After prefilter- ing and multi

  18. Abstract-Proton Computed Tomography (CT) has important implications for both image-guided diagnosis and radiation

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    Abstract- Proton Computed Tomography (CT) has important implications for both image-guided diagnosis and radiation therapy. For diagnosis, the fact that the patient dose committed by proton CT and contrast, may be exploited in dose-critical clinical settings. Proton CT is also the most appropriate

  19. for Proton CT R. P. Johnson, Member, IEEE, V. Bashkirov, V. Giacometti, R. F. Hurley, P. Piersimoni,

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    for Proton CT R. P. Johnson, Member, IEEE, V. Bashkirov, V. Giacometti, R. F. Hurley, P. Piersimoni beam test results with our pre-clinical (Phase-II) head scanner developed for proton computed tomography (pCT). After extensive preclinical testing, pCT will be employed in support of proton therapy

  20. T4DT: Processing 4D CT scans of the Lungs Robert Fowler Joe Warren Yin Zhang

    E-Print Network [OSTI]

    Warren, Joe

    T4DT: Processing 4D CT scans of the Lungs Robert Fowler Joe Warren Yin Zhang Rice University technology for processing time-varying CT scans (4D CT) of the lungs. In particular, we propose to develop these tools to quantitatively assess the effectiveness of current treatments for lung cancer. #12;T4DT

  1. SU-E-J-43: Deformed Planning CT as An Electron Density Substitute for Cone-Beam CT

    SciTech Connect (OSTI)

    Mishra, K [Cleveland State University, Cleveland, OH (United States); Godley, A [Cleveland Clinic, Cleveland, OH (United States)

    2014-06-01T23:59:59.000Z

    Purpose: To confirm that deforming the planning CT to the daily Cone-Beam CTs (CBCT) can provide suitable electron density for adaptive planning. We quantify the dosimetric difference between plans calculated on deformed planning CTs (DPCT) and daily CT-on-rails images (CTOR). CTOR is used as a test of the method as CTOR already contains accurate electron density to compare against. Methods: Five prostate only IMRT patients, each with five CTOR images, were selected and re-planned on Panther (Prowess Inc.) with a uniform 5 mm PTV expansion, prescribed 78 Gy. The planning CT was deformed to match each CTOR using ABAS (Elekta Inc.). Contours were drawn on the CTOR, and copied to the DPCT. The original treatment plan was copied to both the CTOR and DPCT, keeping the center of the prostate as the isocenter. The plans were then calculated using the collapsed cone heterogeneous dose engine of Prowess and typical DVH planning parameters used to compare them. Results: Each DPCT was visually compared to its CTOR with no differences observed. The agreement of the copied CTOR contours with the DPCT anatomy further demonstrated the deformation accuracy. The plans calculated using CTOR and DPCT were compared. Over the 25 plan pairs, the average difference between them for prostate D100, D98 and D95 were 0.5%, 0.2%, and 0.2%; PTV D98, D95 and mean dose: 0.3%, 0.2% and 0.3%; bladder V70, V60 and mean dose: 1.1%, 0.7%, and 0.2%; and rectum mean dose: 0.3%. (D100 is the dose covering 100% of the target; V70 is the volume of the organ receiving 70 Gy). Conclusion: We observe negligible difference between the dose calculated on the DPCT and the CTOR, implying that deformed planning CTs are a suitable substitute for electron density. The method can now be applied to CBCTs. Research version of Panther provided by Prowess Inc. Research version of ABAS provided by Elekta Inc.

  2. Twitter @RoyalHolloway royalholloway.ac.ukfacebook.com Search: Royal Holloway, University of London

    E-Print Network [OSTI]

    Sheldon, Nathan D.

    connect@rhul.ac.uk Tuesday11 Royal Holloway Balkan Ensemble An energetic performance of Balkan music

  3. Law, Justice and Regulation at UEA law-justice-regulation@uea.ac.uk

    E-Print Network [OSTI]

    Everest, Graham R

    .dewing@uea.ac.uk Ivan Diaz-Rainey (NBS) Regulation of energy and environmental markets http://www.uea.ac.uk/nbs/people/People/Academic/Ivan+Diaz- Rainey i.diaz-rainey@uea.ac.uk Catherine Wad- dams (NBS/CCP) Economic regulation, competition, energy1 Network on Law, Justice and Regulation at UEA law-justice-regulation@uea.ac.uk 21 October 2010

  4. Boys and Girls, Be Ambitious! http://www.math.sci.hokudai.ac.jp/message/message-graduates/

    E-Print Network [OSTI]

    Nakamura, Iku

    ://www.math.sci.hokudai.ac.jp/ #12;AIKAWA, Hiroaki WebPage http://www.math.sci.hokudai.ac.jp/ aik/index-j.html Fatou Martin Harnack AKITA, Toshiyuki WebPage http://www.math.sci.hokudai.ac.jp/ akita/ Eilenberg-MacLane Coxeter #12;ASAKURA, Masanori ARAI, Asao ABE, Noriyuki WebPage http://www.math.sci.hokudai.ac.jp/ abenori/ #12;ISHIKAWA, Goo Web

  5. Modification No. M226 Contract No. DE-AC54-00AL66620

    National Nuclear Security Administration (NNSA)

    (16.00). (RA 21) m. Wellness Program. Costs of a Wellness Program to promote employee health and fitness are allowable. This program shall be limited to activities related to...

  6. AC Losses in the MICE Channel Magnets -- Is This a Curse or aBlessing?

    SciTech Connect (OSTI)

    Green, M.A.; Wu, H.; Wang, L.; Kai, L.L.; Jia, L.X.; Yang, S.Q.

    2008-01-31T23:59:59.000Z

    This report discusses the AC losses in the MICE channelmagnets during magnet charging and discharging. This report talks aboutthe three types of AC losses in the MICE magnets; the hysteretic AC lossin the superconductor, the coupling AC loss in the superconductor and theeddy current AC loss in the magnet mandrel and support structure. AClosses increase the heat load at 4 K. The added heat load increases thetemperature of the second stage of the cooler. In addition, AC losscontributes to the temperature rise between the second stage cold headand the high field point of the magnet, which is usually close to themagnet hot spot. These are the curses of AC loss in the MICE magnet thatcan limit the rate at which the magnet can be charge or discharged. Ifone is willing to allow some of the helium that is around the magnet toboil away during a magnet charge or discharge, AC losses can become ablessing. The boil off helium from the AC losses can be used to cool theupper end of the HTS leads and the surrounding shield. The AC losses arepresented for all three types of MICE magnets. The AC loss temperaturedrops within the coupling magnet are presented as an example of how boththe curse and blessing of the AC losses can be combined.

  7. A scanning AC calorimetry technique for the analysis of nano-scale quantities of materials

    E-Print Network [OSTI]

    A scanning AC calorimetry technique for the analysis of nano-scale quantities of materials Kechao OF SCIENTIFIC INSTRUMENTS 83, 114901 (2012) A scanning AC calorimetry technique for the analysis of nano 2012) We present a scanning AC nanocalorimetry method that enables calorimetry measurements at heating

  8. University Policy No.: AC1110 Classification: Academic and Students

    E-Print Network [OSTI]

    Victoria, University of

    other than the university community. DEFINITIONS 2.00 EDUCATIONAL SERVICE CONTRACT means a contract://web.uvic.ca/univsec/pol_pro/pol1000/1002SA.html) 8.00 Approval of an Educational Service Contract will be granted by the Dean andUniversity Policy No.: AC1110 Classification: Academic and Students EDUCATIONAL SERVICE

  9. POLICY ON CALENDAR SUBMISSIONS University Policy No: AC1120

    E-Print Network [OSTI]

    Victoria, University of

    1 POLICY ON CALENDAR SUBMISSIONS University Policy No: AC1120 Classification: Academic and Students relevant university policies and procedures, academic policies and regulations, university fees, courses and programs of study. The purpose of this policy is to outline requirements for publishing the University

  10. University Policy No.: AC1130 Classification: Academic and Students

    E-Print Network [OSTI]

    Victoria, University of

    University Policy No.: AC1130 Classification: Academic and Students Approving Authority: Board Last Editorial Change: Mandated Review: 2018 PURPOSE 1.00 The purpose of this policy is to provide guidance on the establishment and governance of student awards by the university. POLICY 2.00 Student

  11. www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY

    E-Print Network [OSTI]

    de Gispert, Adrià

    but low variable cost capacity (coal-fired plants), and the other building low polluting but high variable in electricity generation market who are planning to expand generation capacity. They are anticipating regulation.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY We consider investments by two types of investors, one building highly polluting

  12. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    parties in the nuclear supply chain whether they are providing decommissioning services, project, or the Parent Body Organisation responsible for decommissioning one the UK legacy nuclear installationswww.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Third Party Nuclear Liability: The Case

  13. www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY

    E-Print Network [OSTI]

    Aickelin, Uwe

    Body Organisation responsible for decommissioning one the UK legacy nuclear installationswww.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY Third Party Nuclear Liability 1207 Anthony Thomas and Raphael J. Heffron With a return to nuclear new build expected in the UK

  14. www.tyndall.ac.uk The Tyndall Centre is

    E-Print Network [OSTI]

    Watson, Andrew

    to bring benefits for greenhouse gas reduction and social and economic development. One of the most by the market-structure behind these projects." The research has developed criteria for evaluating CDM forestry PhD from the Mexico study. Further information: k.brown@uea.ac.uk Please see Tyndall Technical Report

  15. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    of 107 Strategic Eurasian Natural Gas Model for Energy Security and Policy Analysis1 Chi-Kong Chyongwww.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Strategic Eurasian Natural Gas Model for Energy-Kong Chyong and Benjamin F. Hobbs The mathematical formulation of a large-scale equilibrium natural gas

  16. www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY

    E-Print Network [OSTI]

    Aickelin, Uwe

    . Although large-scale natural gas models have been developed and used for energy security and policywww.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY Strategic Eurasian Natural Gas Model-scale equilibrium natural gas simulation model that covers gas markets of the EU and the Former Soviet Union

  17. www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY

    E-Print Network [OSTI]

    Aickelin, Uwe

    in concern about the security of natural gas supply to Europe, particularly supplies from Russia. A numberwww.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY Gas Supply Security in the Baltic, determining its level of security is a virtually impossible. The specific gas supply set up, the structure

  18. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    in place designed to mitigate the effects of a disruption. Keywords Natural Gas, security of supply, Baltic not entirely, by the rise in concern about the security of natural gas supply to Europe, particularly supplieswww.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Gas Supply Security in the Baltic States

  19. ACS DIVISION OF POLYMERIC MATERIALS: SCIENCE AND ENGINEERING

    E-Print Network [OSTI]

    Gilchrist, James F.

    , interpenetrating polymer networks, IPNs. Other topics included the mechanical and morphological aspects of polymers textbook, "Introduction to Physical Polymer Science," with Wiley, 2004. While in retirement, he remains for Polymer Science and Engineering, and served as Education Chairman. His efforts at ACS have included

  20. SCHOOL OF ENGINEERING www.abdn.ac.uk/engineering

    E-Print Network [OSTI]

    Levi, Ran

    , in the planning and commissioning of equipment, and in site and plant supervision. Engineers require a wide rangeSCHOOL OF ENGINEERING www.abdn.ac.uk/engineering POSTGRADUATE GUIDE #12;MSc Renewable Energy MSc Safety Engineering for Oil & Gas MSc Subsea Engineering MSc Oil & Gas Engineering MSc Project Management

  1. www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY

    E-Print Network [OSTI]

    de Gispert, Adrià

    as uncertainties are resolved reduces significantly its expected Levelised Cost Of generating Electricity (LCOE deterministic economic model to identify its LCOE without considering uncertainty. In the second step #12;www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY we identified sources of uncertainty in the design that would affect its LCOE

  2. Introduc)on of lab ac)vi)es

    E-Print Network [OSTI]

    Chen, Po

    ·Overview of lab ac)vi)es #12;·En-Jui (En-Ray) Lee · h@p://www.gg.uwyo.edu/ggstudent/elee8 of Water · The characteris)cs of tsunamis & the early warning systems. #12 · Hydraulic gradient and its calcula)on · How to determina)on of groundwater flow

  3. 1go.warwick.ac.uk/engineering ENGINEERING

    E-Print Network [OSTI]

    Davies, Christopher

    1go.warwick.ac.uk/engineering 2012-13 ENGINEERING UNDERGRADUATE BROCHURE #12;2 Engineering Prospectus 2012-13 "BECAUSE ENGINEERING IS INEXTRICABLY TIED TO PEOPLE, IT CANNOT BE JUST AN APPLIED PHYSICAL SCIENCE; IT IS ALSO AN APPLIED SOCIAL SCIENCE. ... (THE ENGINEER'S)... RAISON D'Ã?TRE IS TO SERVE

  4. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    wind power, long-term contracts, balancing costs JEL Classification Q42, L14, L94 Contact dmgn. The estimated extra trading and balancing costs of a CfD for on-shore wind might be £70 million/yr by 2020www.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Contracting for wind generation EPRG Working

  5. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    www.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Nuclear Energy in the Enlarged European Union of nuclear energy and notes that it has shifted significantly as the European Union has grown from 15 member states to 27. The proportion of member states with nuclear energy experience has increased markedly. Also

  6. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    de Gispert, Adrià

    . The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise fromwww.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Locational-based Coupling of Electricity Markets the effects of varying system characteristics on the magnitude of the locational-based unit commitment

  7. www.weizmann.ac.il/library Introduction 3

    E-Print Network [OSTI]

    to the Library's printed and digital collections, including books, journals, theses, serials, and online lectures Weizmann Institute of Science Libraries 5 Digital Access · Arranging access to newly purchased electronic#12;www.weizmann.ac.il/library 2 Contents Introduction 3 The Library's Website 3 The Library

  8. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    This paper summarises and reviews scholarly and political comment that draws parallels between the current: the nature of the political discourse; the relationship between an ethics-driven societal shift and economic Change, Slavery, Political Rhetoric JEL Classification B15 Contact wjn21@cam.ac.uk Publication August

  9. www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY

    E-Print Network [OSTI]

    Aickelin, Uwe

    www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY Reforming Small Power Systems under Rabindra Nepal and Tooraj Jamasb The pioneering electricity sector reforms in developing Latin American of `successful and comprehensive electricity reforms' in many less-developed countries like Nepal. Nepal's power

  10. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    www.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Reforming Small Power Systems under Political Nepal and Tooraj Jamasb This paper assesses the electricity sector reforms across small power systems make power sector reform in Nepal and similar small systems a more complex process. As international

  11. www.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY

    E-Print Network [OSTI]

    Aickelin, Uwe

    valuation method (CVM) to investigate information effects in the valuation of electricity and waterwww.eprg.group.cam.ac.uk EPRGWORKINGPAPERNON-TECHNICALSUMMARY Information Effects in Valuation of Electricity and Water Service Attributes Using Contingent Valuation EPRG Working Paper 1127 Cambridge Working

  12. www.eprg.group.cam.ac.uk EPRGWORKINGPAPER

    E-Print Network [OSTI]

    Aickelin, Uwe

    factors that affect WTP for the attributes considered. Keywords Contingent Valuation Method, Willingnesswww.eprg.group.cam.ac.uk EPRGWORKINGPAPER Abstract Information Effects in Valuation of Electricity and Water Service Attributes Using Contingent Valuation EPRG Working Paper 1127 Cambridge Working Paper

  13. http://stir.ac.uk/4l Why study Management?

    E-Print Network [OSTI]

    Little, Tony

    http://stir.ac.uk/4l BSc(Hons) Management #12;Why study Management? Management essentially combines the flow of patients through hospital departments. Other modules include: Business Strategy, Project Management Case Studies and Energy Supply Case Study. Did you know? Excellent Management practice is required

  14. Beaming into matter and life www.cockcroft.ac.uk

    E-Print Network [OSTI]

    Crowther, Paul

    Beaming into matter and life www.cockcroft.ac.uk COCKCROFT STRATEGY MAP 2014-2020 Vision Continue and train the next generation of scientists and engineers, address societal challenges in energy · Globally Unique Skills Base · Societal Impact: Energy, Environment, Health, Security Strategic Enablers

  15. contents | print | close www.glasgow.ac.uk

    E-Print Network [OSTI]

    Guo, Zaoyang

    1 contents | print | close www.glasgow.ac.uk Gilmorehill Campus Development Framework June 2014 : Topic 4 107 Approach to Historic Assets: Sub Topics 108 · A Campus-wide Conservation Strategy 108 · Introduction 134 · Relevant Consultation Themes : Topic 7 135 Uses & Adaptability : Sub Topics 136 · Energy

  16. contents | print | close www.glasgow.ac.uk

    E-Print Network [OSTI]

    Guo, Zaoyang

    1 contents | print | close www.glasgow.ac.uk Gilmorehill Campus Development Framework FINAL : Topic 4 107 Approach to Historic Assets: Sub Topics 108 · A Campus-wide Conservation Strategy 108 · Introduction 134 · Relevant Consultation Themes : Topic 7 135 Uses & Adaptability : Sub Topics 136 · Energy

  17. Self-induced ac Stark shift in lasers

    SciTech Connect (OSTI)

    Gil, L.; Lippi, G. L. [Universite de Nice Sophia Antipolis, Institut Non Lineaire de Nice, and CNRS, UMR 6618 1361 Route des Lucioles, F-06560 Valbonne (France)

    2011-04-15T23:59:59.000Z

    The ac Stark effect is a well-known, well-established effect associated with the displacement of the atomic energy levels in the presence of an electromagnetic (e.m.) field. As the origin of the e.m. field is irrelevant, a self-induced ac Stark effect should be present in a laser. However, not only has this effect never been reported but it is not included in any laser model. Here, we show that a self-induced ac Stark shift does exist in the theoretical description of a two-level laser, provided that the reduced equations are derived not from the rotating-wave approximation, but from the full density matrix formulation. Interesting fundamental consequences are discussed and quantitative estimates of the self-induced frequency shift resulting from the laser field's ac Stark shift are obtained for a variety of lasers. We find that the effect is generally small but (at least in some cases) measurable and that the transfer of laser amplitude noise into frequency noise may play a role in future, ultrahigh-precision metrological applications.

  18. www.glasgow.ac.uk/library The University Library

    E-Print Network [OSTI]

    Guo, Zaoyang

    www.glasgow.ac.uk/library The University Library for staff #12;www.facebook.com/uofglibrary twitter.com/uofglibrary instagram.com/uoglibrary Library Blog universityofglasgowlibrary.wordpress.com Welcome to the University Library Where is the Library? It's on Hillhead Street, next to the Hunterian Art Gallery, at the heart

  19. Glasgow Theses Service http://theses.gla.ac.uk/

    E-Print Network [OSTI]

    Singer, Jeremy

    transmission and the ecological context. PhD thesis. http://theses.gla.ac.uk/3768/ Copyright and moral rights first obtaining permission in writing from the Author The content must not be changed in any way or sold must be given #12;Disease transmission and the ecological context Angus Cameron BSc (Hons) This thesis

  20. FBDEditor: {ldalove, atang34, syjsmk, jbyoo}@konkuk.ac.kr

    E-Print Network [OSTI]

    }@konkuk.ac.kr : Programmable Logic Controller (PLC) . Field Programmable Gate Array (FPGA) . PLC Function Controller (PLC) Field Programmable Gate Array (FPGA) . PLC IEC 61131-3 5 (LD: Ladder diagram) . FBD Function Block(FB) . FBD PLC . FPGA Hardware Description Language

  1. Glasgow Theses Service http://theses.gla.ac.uk/

    E-Print Network [OSTI]

    Glasgow, University of

    within the acceptance of the acceleration system. Ionisation cooling is the only viable cooling technique (2011) The Muon Ionisation Cooling Experiment. PhD thesis. http://theses.gla.ac.uk/2839/ Copyright-commercial research or study, without prior permission or charge This thesis cannot be reproduced or quoted

  2. Efficiency Ratings for the Daiken AC (Americas), Inc.

    E-Print Network [OSTI]

    Efficiency Ratings for the Daiken AC (Americas), Inc. Altherma Air-to-Water Source Heat Pump System is used to provide water heating, the EF for that separate water heater shall be used for performance Description Model No. Capacity (tons) Space Heating Space Cooling SEER Water Heating Efficiency

  3. CtIP tetramer assembly is required for DNA-end resection and repair

    E-Print Network [OSTI]

    Davies, Owen R.; Forment, Josep V.; Sun, Meidai; Belotserkovskaya, Rimma; Coates, Julia; Galanty, Yaron; Demir, Mukerrem; Morton, Christopher; Rzechorzek, Neil; Jackson, Stephen P.; Pellegrini, Luca

    2015-01-05T23:59:59.000Z

    1     CtIP tetramer assembly is required for DNA-end resection and repair Owen R. Davies1,4*, Josep V. Forment1,2,3*, Meidai Sun1, Rimma Belotserkovskaya1,2, Julia Coates1,2, Yaron Galanty1,2, Mukerrem Demir1,2, Christopher Morton1... that a CtIP tetramer architecture is essential for effective DSB repair by homologous recombination. Keywords CtIP/RBBP8, double-strand DNA break repair, DNA-end resection, gene conversion, homologous recombination. 3...

  4. Optimization of spin-torque switching using AC and DC pulses

    SciTech Connect (OSTI)

    Dunn, Tom [Department of Physics, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Kamenev, Alex [Department of Physics, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Fine Theoretical Physics Institute, University of Minnesota, Minneapolis, Minnesota 55455 (United States)

    2014-06-21T23:59:59.000Z

    We explore spin-torque induced magnetic reversal in magnetic tunnel junctions using combined AC and DC spin-current pulses. We calculate the optimal pulse times and current strengths for both AC and DC pulses as well as the optimal AC signal frequency, needed to minimize the Joule heat lost during the switching process. The results of this optimization are compared against numeric simulations. Finally, we show how this optimization leads to different dynamic regimes, where switching is optimized by either a purely AC or DC spin-current, or a combination AC/DC spin-current, depending on the anisotropy energies and the spin-current polarization.

  5. Iterative image-domain decomposition for dual-energy CT

    SciTech Connect (OSTI)

    Niu, Tianye; Dong, Xue; Petrongolo, Michael; Zhu, Lei, E-mail: leizhu@gatech.edu [Nuclear and Radiological Engineering and Medical Physics Programs, The George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States)] [Nuclear and Radiological Engineering and Medical Physics Programs, The George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States)

    2014-04-15T23:59:59.000Z

    Purpose: Dual energy CT (DECT) imaging plays an important role in advanced imaging applications due to its capability of material decomposition. Direct decomposition via matrix inversion suffers from significant degradation of image signal-to-noise ratios, which reduces clinical values of DECT. Existing denoising algorithms achieve suboptimal performance since they suppress image noise either before or after the decomposition and do not fully explore the noise statistical properties of the decomposition process. In this work, the authors propose an iterative image-domain decomposition method for noise suppression in DECT, using the full variance-covariance matrix of the decomposed images. Methods: The proposed algorithm is formulated in the form of least-square estimation with smoothness regularization. Based on the design principles of a best linear unbiased estimator, the authors include the inverse of the estimated variance-covariance matrix of the decomposed images as the penalty weight in the least-square term. The regularization term enforces the image smoothness by calculating the square sum of neighboring pixel value differences. To retain the boundary sharpness of the decomposed images, the authors detect the edges in the CT images before decomposition. These edge pixels have small weights in the calculation of the regularization term. Distinct from the existing denoising algorithms applied on the images before or after decomposition, the method has an iterative process for noise suppression, with decomposition performed in each iteration. The authors implement the proposed algorithm using a standard conjugate gradient algorithm. The method performance is evaluated using an evaluation phantom (Catphan©600) and an anthropomorphic head phantom. The results are compared with those generated using direct matrix inversion with no noise suppression, a denoising method applied on the decomposed images, and an existing algorithm with similar formulation as the proposed method but with an edge-preserving regularization term. Results: On the Catphan phantom, the method maintains the same spatial resolution on the decomposed images as that of the CT images before decomposition (8 pairs/cm) while significantly reducing their noise standard deviation. Compared to that obtained by the direct matrix inversion, the noise standard deviation in the images decomposed by the proposed algorithm is reduced by over 98%. Without considering the noise correlation properties in the formulation, the denoising scheme degrades the spatial resolution to 6 pairs/cm for the same level of noise suppression. Compared to the edge-preserving algorithm, the method achieves better low-contrast detectability. A quantitative study is performed on the contrast-rod slice of Catphan phantom. The proposed method achieves lower electron density measurement error as compared to that by the direct matrix inversion, and significantly reduces the error variation by over 97%. On the head phantom, the method reduces the noise standard deviation of decomposed images by over 97% without blurring the sinus structures. Conclusions: The authors propose an iterative image-domain decomposition method for DECT. The method combines noise suppression and material decomposition into an iterative process and achieves both goals simultaneously. By exploring the full variance-covariance properties of the decomposed images and utilizing the edge predetection, the proposed algorithm shows superior performance on noise suppression with high image spatial resolution and low-contrast detectability.

  6. Temporal and spectral imaging with micro-CT

    SciTech Connect (OSTI)

    Johnston, Samuel M.; Johnson, G. Allan; Badea, Cristian T. [Center for In Vivo Microscopy, Duke University Medical Center, Durham, North Carolina 27710 (United States)

    2012-08-15T23:59:59.000Z

    Purpose: Micro-CT is widely used for small animal imaging in preclinical studies of cardiopulmonary disease, but further development is needed to improve spatial resolution, temporal resolution, and material contrast. We present a technique for visualizing the changing distribution of iodine in the cardiac cycle with dual source micro-CT. Methods: The approach entails a retrospectively gated dual energy scan with optimized filters and voltages, and a series of computational operations to reconstruct the data. Projection interpolation and five-dimensional bilateral filtration (three spatial dimensions + time + energy) are used to reduce noise and artifacts associated with retrospective gating. We reconstruct separate volumes corresponding to different cardiac phases and apply a linear transformation to decompose these volumes into components representing concentrations of water and iodine. Since the resulting material images are still compromised by noise, we improve their quality in an iterative process that minimizes the discrepancy between the original acquired projections and the projections predicted by the reconstructed volumes. The values in the voxels of each of the reconstructed volumes represent the coefficients of linear combinations of basis functions over time and energy. We have implemented the reconstruction algorithm on a graphics processing unit (GPU) with CUDA. We tested the utility of the technique in simulations and applied the technique in an in vivo scan of a C57BL/6 mouse injected with blood pool contrast agent at a dose of 0.01 ml/g body weight. Postreconstruction, at each cardiac phase in the iodine images, we segmented the left ventricle and computed its volume. Using the maximum and minimum volumes in the left ventricle, we calculated the stroke volume, the ejection fraction, and the cardiac output. Results: Our proposed method produces five-dimensional volumetric images that distinguish different materials at different points in time, and can be used to segment regions containing iodinated blood and compute measures of cardiac function. Conclusions: We believe this combined spectral and temporal imaging technique will be useful for future studies of cardiopulmonary disease in small animals.

  7. Sensorless Direct Torque Control For Salient Pole PMSM Based on Extended Kalman Filter Fed By AC/DC/AC Converter

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Sensorless Direct Torque Control For Salient ­ Pole PMSM Based on Extended Kalman Filter Fed By AC is proposed. The Direct Torque Control (DTC) technique for PMSM is receiving increasing attention due on the stochastic intromission, in others words, noise. The PMSM is fed by an indirect power electronic converter

  8. Impact of tumor size and tracer uptake heterogeneity in F-FDG PET and CT NonSmall Cell Lung Cancer

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    heterogeneity on various PET uptake delineation approaches. Methods: 25 NSCLC cancer patients with 18F-FDG PET/CT increasingly used for staging Non-small Cell Lung Cancer (NSCLC) (1). In addition, the use of 18 F-FDG PET/CT F-FDG), associated with Computed Tomography (CT) since the development of PET/CT devices, has been

  9. RIS-M-2586 ELASTIC-PLASTIC FRACTURE MECHANICS ANALYSIS OF A CT-SPECIMEN

    E-Print Network [OSTI]

    RISØ-M-2586 ELASTIC-PLASTIC FRACTURE MECHANICS ANALYSIS OF A CT-SPECIMEN - A TWO-DIMENSIONAL APPROACH Gunner C. Larsen Abstract. This report documents the results obtained from an elastic-plastic

  10. angiographic c-arm ct: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Christchurch Medical School) Summary The MARS-CT team has had great success over the past 6 months with support portfolio. This support underpins the research and development to...

  11. Low-Dose Spiral CT Scans for Early Lung Cancer Detection

    Broader source: Energy.gov [DOE]

    Low-dose spiral computed tomography (CT) scanning is a noninvasive medical imaging test that has been used for the early detection of lung cancer for over 16 years (Sone et al. 1998; Henschke et.al. 1999).

  12. r XXXX American Chemical Society A dx.doi.org/10.1021/ct2002804 |J. Chem. Theory Comput. XXXX, XXX, 000000 pubs.acs.org/JCTC

    E-Print Network [OSTI]

    Baer, Roi

    ) with conventional functionals for "charge-transfer-like" excitations in oligoacenes. We show that this failure range-separation parameter. Here, we explain why this approach should succeed where conventional the success of this approach on the oligoacene series and on related hydrocarbons. This resolves a long

  13. Lung nodule detection in low-dose and high-resolution CT scans

    E-Print Network [OSTI]

    Delogu, P; Gori, I; Preite Martínez, A; Retico, A; Tata, A

    2006-01-01T23:59:59.000Z

    We are developing a computer-aided detection (CAD) system for the identification of small pulmonary nodules in screening CT scans. The main modules of our system, i.e. a dot-enhancement filter for nodule candidate selection and a neural classifier for false positive finding reduction, are described. The preliminary results obtained on the so-far collected database of lung CT are discussed.

  14. Semi-automatic delineation using weighted CT-MRI registered images for radiotherapy of nasopharyngeal cancer

    SciTech Connect (OSTI)

    Fitton, I. [European Georges Pompidou Hospital, Department of Radiology, 20 rue Leblanc, 75015, Paris (France); Cornelissen, S. A. P. [Image Sciences Institute, UMC, Department of Radiology, P.O. Box 85500, 3508 GA Utrecht (Netherlands); Duppen, J. C.; Rasch, C. R. N.; Herk, M. van [The Netherlands Cancer Institute-Antoni van Leeuwenhoek Hospital, Department of Radiotherapy, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Steenbakkers, R. J. H. M. [University Medical Center Groningen, Department of Radiation Oncology, Hanzeplein 1, 9713 GZ Groningen (Netherlands); Peeters, S. T. H. [UZ Gasthuisberg, Herestraat 49, 3000 Leuven, Belgique (Belgium); Hoebers, F. J. P. [Maastricht University Medical Center, Department of Radiation Oncology (MAASTRO clinic), GROW School for Oncology and Development Biology Maastricht, 6229 ET Maastricht (Netherlands); Kaanders, J. H. A. M. [UMC St-Radboud, Department of Radiotherapy, Geert Grooteplein 32, 6525 GA Nijmegen (Netherlands); Nowak, P. J. C. M. [ERASMUS University Medical Center, Department of Radiation Oncology,Groene Hilledijk 301, 3075 EA Rotterdam (Netherlands)

    2011-08-15T23:59:59.000Z

    Purpose: To develop a delineation tool that refines physician-drawn contours of the gross tumor volume (GTV) in nasopharynx cancer, using combined pixel value information from x-ray computed tomography (CT) and magnetic resonance imaging (MRI) during delineation. Methods: Operator-guided delineation assisted by a so-called ''snake'' algorithm was applied on weighted CT-MRI registered images. The physician delineates a rough tumor contour that is continuously adjusted by the snake algorithm using the underlying image characteristics. The algorithm was evaluated on five nasopharyngeal cancer patients. Different linear weightings CT and MRI were tested as input for the snake algorithm and compared according to contrast and tumor to noise ratio (TNR). The semi-automatic delineation was compared with manual contouring by seven experienced radiation oncologists. Results: A good compromise for TNR and contrast was obtained by weighing CT twice as strong as MRI. The new algorithm did not notably reduce interobserver variability, it did however, reduce the average delineation time by 6 min per case. Conclusions: The authors developed a user-driven tool for delineation and correction based a snake algorithm and registered weighted CT image and MRI. The algorithm adds morphological information from CT during the delineation on MRI and accelerates the delineation task.

  15. Tsovaltzi, D., Weinberger, A., Scheuer, O., Dragon, T. & McLaren, B.M., (2012). Argument diagrams in Facebook: Facilitating the formation of scientifically sound opinions. In: A. Ra-

    E-Print Network [OSTI]

    McLaren, Bruce Martin

    2012-01-01T23:59:59.000Z

    in Facebook: Facilitating the formation of scientifically sound opinions. In: A. Ra- venscroft, S. Lindstaedt in Facebook: Facilitating the Formation of Scientifically Sound Opinions Dimitra Tsovaltzi, Armin Weinberger Dimitra.tsovalzi@mx.uni-saarland.de Students use Facebook to organize their classroom experiences [1

  16. 85R.A. Calvo and S.K. D'Mello (eds.), New Perspectives on Affect and Learning Technologies, Explorations in the Learning Sciences, Instructional Systems and Performance Technologies 3,

    E-Print Network [OSTI]

    Young, R. Michael

    85R.A. Calvo and S.K. D'Mello (eds.), New Perspectives on Affect and Learning Technologies to which he or she is motivated to continue with the learning process (Kort, Reilly, & Picard, 2001; Picard work (Arroyo, Woolf, Royer, & Tai, 2009; Chaffar & Frasson, 2004; D'Mello et al., 2008; Forbes- Riley

  17. Citation: Myers, R.A. and C.A. Ottensmeyer.(2005, in press). Extinction Risk in Marine Species. in Norse, E.A. and L.B. Crowder, eds. Marine Conservation Biology: The Science of Maintaining the Sea's Biodiversity. Island

    E-Print Network [OSTI]

    Myers, Ransom A.

    Citation: Myers, R.A. and C.A. Ottensmeyer.(2005, in press). Extinction Risk in Marine Species's Biodiversity. Island Press, Washington DC (USA) Chapter 5 Extinction Risk in Marine Species Ransom A. Myers C resources seemed inexhaustible, its capacity boundless. Marine species have even been considered "extinction

  18. Tel: +44 (0) 1603 591574 Email: business@uea.ac.uk Web: www.uea.ac.uk/business Experts model buyer behaviour

    E-Print Network [OSTI]

    Everest, Graham R

    Tel: +44 (0) 1603 591574 Email: business@uea.ac.uk Web: www.uea.ac.uk/business Experts model buyer their customers to make buying decisions. When you are in the business of printing newspapers, accurate ­ the UK's largest independently-owned regional media business ­ on a project which saw academics from

  19. Approaches to building single-stage AC/AC conversion switch-mode audio power Petar Ljusev and Michael A.E. Andersen

    E-Print Network [OSTI]

    power amplifiers with a separate power supply, it is expected that direct conversion will provide better performance. It is also quite appealing for the Active Trans- ducer (AT) [2] approach for direct conversionApproaches to building single-stage AC/AC conversion switch-mode audio power amplifiers Petar

  20. Development Office, Trinity Hall, Cambridge, CB2 1TJ www.trinhall.cam.ac.uk fundraising@trinhall.cam.ac.uk

    E-Print Network [OSTI]

    Lasenby, Joan

    Development Office, Trinity Hall, Cambridge, CB2 1TJ www.trinhall.cam.ac.uk fundraising@trinhall.cam.ac.uk Tel: 01223 766345 Fax: 01223 765157 Trinity Hall Cambridge registered charity number 1137458 Making of financial background, and we are committed to nurturing the talent of the diverse Trinity Hall community

  1. Prebreakdown and breakdown phenomena in large oil gaps under AC

    SciTech Connect (OSTI)

    Saker, A.; Gournay, P.; Lesaint, O.; Tobazeon, R. [CNRS, Grenoble (France). Lab. d`Electrostatique et de Materiaux Dielectriques; Trinh, N.G. [Inst. de Recherche d`Hydro-Quebec, Varennes, Quebec (Canada); Boisdon, C. [Jeumont-Schneider Transformateurs, Lyon (France)

    1996-12-31T23:59:59.000Z

    This paper presents a study of prebreakdown and breakdown phenomena under AC voltage in mineral oil in large gaps to 60 cm. The investigations presented concern the study of streamers and the measurement of breakdown voltages in rod-plane and sphere-plane gaps. Also, the influence of a contamination by solid particles in the oil has been considered. A specific breakdown mode under AC voltage is evidenced, where bursts of streamers lead to the lowest breakdown fields recorded. Numerical values of the mean field in oil required for direct or burst breakdown modes are derived from the experiments. As a consequence, the great sensitivity to the presence of particles on EHV transformers insulation with large oil gaps is pointed out.

  2. On-Chip AC self-test controller

    DOE Patents [OSTI]

    Flanagan, John D. (Rhinebeck, NY); Herring, Jay R. (Poughkeepsie, NY); Lo, Tin-Chee (Fishkill, NY)

    2009-09-29T23:59:59.000Z

    A system for performing AC self-test on an integrated circuit that includes a system clock for normal operation is provided. The system includes the system clock, self-test circuitry, a first and second test register to capture and launch test data in response to a sequence of data pulses, and a logic circuit to be tested. The self-test circuitry includes an AC self-test controller and a clock splitter. The clock splitter generates the sequence of data pulses including a long data capture pulse followed by an at speed data launch pulse and an at speed data capture pulse followed by a long data launch pulse. The at speed data launch pulse and the at speed data capture pulse are generated for a common cycle of the system clock.

  3. SNL software manual for the ACS Data Analytics Project.

    SciTech Connect (OSTI)

    Stearley, Jon R.; McLendon, William Clarence, III; Rodrigues, Arun F.; Williams, Aaron S.; Hooper, Russell Warren; Robinson, David Gerald; Stickland, Michael G.

    2011-10-01T23:59:59.000Z

    In the ACS Data Analytics Project (also known as 'YumYum'), a supercomputer is modeled as a graph of components and dependencies, jobs and faults are simulated, and component fault rates are estimated using the graph structure and job pass/fail outcomes. This report documents the successful completion of all SNL deliverables and tasks, describes the software written by SNL for the project, and presents the data it generates. Readers should understand what the software tools are, how they fit together, and how to use them to reproduce the presented data and additional experiments as desired. The SNL YumYum tools provide the novel simulation and inference capabilities desired by ACS. SNL also developed and implemented a new algorithm, which provides faster estimates, at finer component granularity, on arbitrary directed acyclic graphs.

  4. Lung Dose Calculation With SPECT/CT for {sup 90}Yittrium Radioembolization of Liver Cancer

    SciTech Connect (OSTI)

    Yu, Naichang, E-mail: yun@ccf.org [Department of Radiation Oncology, Cleveland Clinic, Cleveland, OH (United States)] [Department of Radiation Oncology, Cleveland Clinic, Cleveland, OH (United States); Srinivas, Shaym M.; DiFilippo, Frank P.; Shrikanthan, Sankaran [Department of Nuclear Medicine, Cleveland Clinic, Cleveland, OH (United States)] [Department of Nuclear Medicine, Cleveland Clinic, Cleveland, OH (United States); Levitin, Abraham; McLennan, Gordon; Spain, James [Department of Interventional Radiology, Cleveland Clinic, Cleveland, OH (United States)] [Department of Interventional Radiology, Cleveland Clinic, Cleveland, OH (United States); Xia, Ping; Wilkinson, Allan [Department of Radiation Oncology, Cleveland Clinic, Cleveland, OH (United States)] [Department of Radiation Oncology, Cleveland Clinic, Cleveland, OH (United States)

    2013-03-01T23:59:59.000Z

    Purpose: To propose a new method to estimate lung mean dose (LMD) using technetium-99m labeled macroaggregated albumin ({sup 99m}Tc-MAA) single photon emission CT (SPECT)/CT for {sup 90}Yttrium radioembolization of liver tumors and to compare the LMD estimated using SPECT/CT with clinical estimates of LMD using planar gamma scintigraphy (PS). Methods and Materials: Images of 71 patients who had SPECT/CT and PS images of {sup 99m}Tc-MAA acquired before TheraSphere radioembolization of liver cancer were analyzed retrospectively. LMD was calculated from the PS-based lung shunt assuming a lung mass of 1 kg and 50 Gy per GBq of injected activity shunted to the lung. For the SPECT/CT-based estimate, the LMD was calculated with the activity concentration and lung volume derived from SPECT/CT. The effect of attenuation correction and the patient's breathing on the calculated LMD was studied with the SPECT/CT. With these effects correctly taken into account in a more rigorous fashion, we compared the LMD calculated with SPECT/CT with the LMD calculated with PS. Results: The mean dose to the central region of the lung leads to a more accurate estimate of LMD. Inclusion of the lung region around the diaphragm in the calculation leads to an overestimate of LMD due to the misregistration of the liver activity to the lung from the patient's breathing. LMD calculated based on PS is a poor predictor of the actual LMD. For the subpopulation with large lung shunt, the mean overestimation from the PS method for the lung shunt was 170%. Conclusions: A new method of calculating the LMD for TheraSphere and SIR-Spheres radioembolization of liver cancer based on {sup 99m}Tc-MAA SPECT/CT is presented. The new method provides a more accurate estimate of radiation risk to the lungs. For patients with a large lung shunt calculated from PS, a recalculation of LMD based on SPECT/CT is recommended.

  5. Variable Frequency AC Drives for Cooling Tower Energy Efficiency

    E-Print Network [OSTI]

    Corey, R. W.

    1982-01-01T23:59:59.000Z

    speed fan drives. Fan speed is reduced to yield specific water temperatures at thermal conditions less difficult than design. The reduced air flow is accomplished by reduced fan power consumption, resulting in optimum cooling tower operation... and economics. Automatic fan speed control by sensing cold water temperature is the economic essence of the application of adjustable frequency power to A-C fan motors. 2.2 Cell Partitions In some multi-cell mechanical-draft cooling towers, the isolation...

  6. Hybrid immersed interface-immersed boundary methods for AC dielectrophoresis

    SciTech Connect (OSTI)

    Hossan, Mohammad Robiul [School of Mechanical and Materials Engineering, Washington State University, Pullman, WA 99164-2920 (United States); Department of Engineering and Physics, University of Central Oklahoma, Edmond, OK 73034-5209 (United States); Dillon, Robert [Department of Mathematics, Washington State University, Pullman, WA 99164-3113 (United States); Dutta, Prashanta, E-mail: dutta@mail.wsu.edu [School of Mechanical and Materials Engineering, Washington State University, Pullman, WA 99164-2920 (United States)

    2014-08-01T23:59:59.000Z

    Dielectrophoresis, a nonlinear electrokinetic transport mechanism, has become popular in many engineering applications including manipulation, characterization and actuation of biomaterials, particles and biological cells. In this paper, we present a hybrid immersed interface–immersed boundary method to study AC dielectrophoresis where an algorithm is developed to solve the complex Poisson equation using a real variable formulation. An immersed interface method is employed to obtain the AC electric field in a fluid media with suspended particles and an immersed boundary method is used for the fluid equations and particle transport. The convergence of the proposed algorithm as well as validation of the hybrid scheme with experimental results is presented. In this paper, the Maxwell stress tensor is used to calculate the dielectrophoretic force acting on particles by considering the physical effect of particles in the computational domain. Thus, this study eliminates the approximations used in point dipole methods for calculating dielectrophoretic force. A comparative study between Maxwell stress tensor and point dipole methods for computing dielectrophoretic forces are presented. The hybrid method is used to investigate the physics of dielectrophoresis in microfluidic devices using an AC electric field. The numerical results show that with proper design and appropriate selection of applied potential and frequency, global electric field minima can be obtained to facilitate multiple particle trapping by exploiting the mechanism of negative dielectrophoresis. Our numerical results also show that electrically neutral particles form a chain parallel to the applied electric field irrespective of their initial orientation when an AC electric field is applied. This proposed hybrid numerical scheme will help to better understand dielectrophoresis and to design and optimize microfluidic devices.

  7. Measurements of AC Losses and Current Distribution in Superconducting Cables

    SciTech Connect (OSTI)

    Nguyen, Doan A [Los Alamos National Laboratory (LANL); Ashworth, Stephen P [Los Alamos National Laboratory (LANL); Duckworth, Robert C [ORNL; Carter, Bill [AMSC; Fleshler, Steven [AMER Superconductor Corp, Devens, MA 01434

    2011-01-01T23:59:59.000Z

    This paper presents our new experimental facility and techniques to measure ac loss and current distribution between the layers for High Temperature Superconducting (HTS) cables. The facility is powered with a 45 kVA three-phase power supply which can provide three-phase currents up to 5 kA per phase via high current transformers. The system is suitable for measurements at any frequency between 20 and 500 Hz to better understand the ac loss mechanisms in HTS cables. In this paper, we will report techniques and results for ac loss measurements carried out on several HTS cables with and without an HTS shielding layer. For cables without a shielding layer, care must be taken to control the effect of the magnetic fields from return currents on loss measurements. The waveform of the axial magnetic field was also measured by a small pick-up coil placed inside a two-layer cable. The temporal current distribution between the layers can be calculated from the waveform of the axial field.

  8. Assessment of US electric vehicle programs with ac powertrains

    SciTech Connect (OSTI)

    Kevala, R.J. (Booz, Allen and Hamilton, Inc., Bethesda, MD (USA). Transportation Consulting Div.)

    1990-02-01T23:59:59.000Z

    AC powertrain technology is a promising approach to improving the performance of electric vehicles. Four major programs are now under way in the United States to develop ac powertrains: the Ford/General Electric single-shaft electric propulsion system (ETX-II), the Eaton dual-shaft electric propulsion system (DSEP), the Jet Propulsion Laboratories (JPL) integrated ac motor drive and recharge system, and the Massachusetts Institute of Technology (MIT) variable reluctance motor (VRM) drive. The JPL program is sponsored by EPRI; the other three programs are funded by the US Department of Energy. This preliminary assessment of the four powertrain programs focuses on potential performance, costs, safety, and commercial feasibility. Interviews with program personnel were supplemented by computer simulations of electric vehicle performance using the four systems. Each of the four powertrains appears superior to standard dc powertrain technology in terms of performance and weight. The powertrain technologies studied in this assessment are at varying degrees of technological maturity. One or more of the systems may be ready for incorporation into an advanced electric vehicle during the early 1990s. Each individual report will have a separate abstract. 5 refs., 37 figs., 29 tabs.

  9. System and method for determining stator winding resistance in an AC motor

    DOE Patents [OSTI]

    Lu, Bin (Kenosha, WI); Habetler, Thomas G. (Snellville, GA); Zhang, Pinjia (Atlanta, GA); Theisen, Peter J. (West Bend, WI)

    2011-05-31T23:59:59.000Z

    A system and method for determining stator winding resistance in an AC motor is disclosed. The system includes a circuit having an input connectable to an AC source and an output connectable to an input terminal of an AC motor. The circuit includes at least one contactor and at least one switch to control current flow and terminal voltages in the AC motor. The system also includes a controller connected to the circuit and configured to modify a switching time of the at least one switch to create a DC component in an output of the system corresponding to an input to the AC motor and determine a stator winding resistance of the AC motor based on the injected DC component of the voltage and current.

  10. Programmable AC power supply for simulating power transient expected in fusion reactor

    SciTech Connect (OSTI)

    Halimi, B. [Seoul National Univ., Seoul 151-744 (Korea, Republic of); Suh, K. Y. [Seoul National Univ., Seoul 151-744 (Korea, Republic of); PHILOSOPHIA, 1 Gwanak Ro, Gwanak Gu, Seoul 151-744 (Korea, Republic of)

    2012-07-01T23:59:59.000Z

    This paper focus on control engineering of the programmable AC power source which has capability to simulate power transient expected in fusion reactor. To generate the programmable power source, AC-AC power electronics converter is adopted to control the power of a set of heaters to represent the transient phenomena of heat exchangers or heat sources of a fusion reactor. The International Thermonuclear Experimental Reactor (ITER) plasma operation scenario is used as the basic reference for producing this transient power source. (authors)

  11. Nonlinear modal interaction in HVDC/AC power systems with dc power modulation

    SciTech Connect (OSTI)

    Ni, Y.X. [Tsinghua Univ., Beijing (China)] [Tsinghua Univ., Beijing (China); Vittal, V.; Kliemann, W.; Fouad, A.A. [Iowa State Univ., Ames, IA (United States)] [Iowa State Univ., Ames, IA (United States)

    1996-11-01T23:59:59.000Z

    In this paper investigation of nonlinear modal interaction using the normal form of vector fields technique is extended to HVDC/AC power systems with dc power modulation. The ac-dc interface equations are solved to form a state space model with second order approximation. Using the normal form technique, the system`s nonlinear dynamic characteristics are obtained. The proposed approach is applied to a 4-generator HVDC/AC test power system, and compare with the time domain solution.

  12. A reduction of proof complexity to computational complexity for AC0

    E-Print Network [OSTI]

    Krajíèek, Jan

    obtained. Ajtai [3, 4, 5], Beame 1 #12;et.al.[6] and Buss et.al.[9] proved lower bounds for AC0 Frege a prime p do not polyno- mially simulate polynomial calculus over Fp, and recently Buss, Kolodziejczyk by the depth 3 AC0 [p] system. Also, Buss et.al.[9] showed that the AC0 [p] Frege systems are polynomially

  13. MRI-based treatment planning with pseudo CT generated through atlas registration

    SciTech Connect (OSTI)

    Uh, Jinsoo, E-mail: jinsoo.uh@stjude.org; Merchant, Thomas E.; Hua, Chiaho [Department of Radiological Sciences, St. Jude Children's Research Hospital, Memphis, Tennessee 38105 (United States)] [Department of Radiological Sciences, St. Jude Children's Research Hospital, Memphis, Tennessee 38105 (United States); Li, Yimei; Li, Xingyu [Department of Biostatistics, St. Jude Children's Research Hospital, Memphis, Tennessee 38105 (United States)] [Department of Biostatistics, St. Jude Children's Research Hospital, Memphis, Tennessee 38105 (United States)

    2014-05-15T23:59:59.000Z

    Purpose: To evaluate the feasibility and accuracy of magnetic resonance imaging (MRI)-based treatment planning using pseudo CTs generated through atlas registration. Methods: A pseudo CT, providing electron density information for dose calculation, was generated by deforming atlas CT images previously acquired on other patients. The authors tested 4 schemes of synthesizing a pseudo CT from single or multiple deformed atlas images: use of a single arbitrarily selected atlas, arithmetic mean process using 6 atlases, and pattern recognition with Gaussian process (PRGP) using 6 or 12 atlases. The required deformation for atlas CT images was derived from a nonlinear registration of conjugated atlas MR images to that of the patient of interest. The contrasts of atlas MR images were adjusted by histogram matching to reduce the effect of different sets of acquisition parameters. For comparison, the authors also tested a simple scheme assigning the Hounsfield unit of water to the entire patient volume. All pseudo CT generating schemes were applied to 14 patients with common pediatric brain tumors. The image similarity of real patient-specific CT and pseudo CTs constructed by different schemes was compared. Differences in computation times were also calculated. The real CT in the treatment planning system was replaced with the pseudo CT, and the dose distribution was recalculated to determine the difference. Results: The atlas approach generally performed better than assigning a bulk CT number to the entire patient volume. Comparing atlas-based schemes, those using multiple atlases outperformed the single atlas scheme. For multiple atlas schemes, the pseudo CTs were similar to the real CTs (correlation coefficient, 0.787–0.819). The calculated dose distribution was in close agreement with the original dose. Nearly the entire patient volume (98.3%–98.7%) satisfied the criteria of chi-evaluation (<2% maximum dose and 2 mm range). The dose to 95% of the volume and the percentage of volume receiving at least 95% of the prescription dose in the planning target volume differed from the original values by less than 2% of the prescription dose (root-mean-square, RMS < 1%). The PRGP scheme did not perform better than the arithmetic mean process with the same number of atlases. Increasing the number of atlases from 6 to 12 often resulted in improvements, but statistical significance was not always found. Conclusions: MRI-based treatment planning with pseudo CTs generated through atlas registration is feasible for pediatric brain tumor patients. The doses calculated from pseudo CTs agreed well with those from real CTs, showing dosimetric accuracy within 2% for the PTV when multiple atlases were used. The arithmetic mean process may be a reasonable choice over PRGP for the synthesis scheme considering performance and computational costs.

  14. DE-AC05-00OR22725 Modification No. 341

    E-Print Network [OSTI]

    Government) to enter into Contract DE-AC05-990R22725 for the Management and Operationofthe OakRidge National

  15. DE-AC05-00OR22725 Modification No. 341

    E-Print Network [OSTI]

    and the Contractor entered into Agreement No. DE-AC05-000R22725, or a Supplemental Agreement(s) thereto, providing

  16. Brachial Plexus Injury from CT-Guided RF Ablation Under General Anesthesia

    SciTech Connect (OSTI)

    Shankar, Sridhar, E-mail: shankars@ummhc.org; Sonnenberg, Eric van; Silverman, Stuart G.; Tuncali, Kemal [Brigham and Women's Hospital, Department of Radiology (United States); Flanagan, Hugh L. [Brigham and Women's Hospital, Department of Anesthesia (United States); Whang, Edward E. [Brigham and Women's Hospital, Department of Surgery (United States)

    2005-06-15T23:59:59.000Z

    Brachial plexus injury in a patient under general anesthesia (GA) is not uncommon, despite careful positioning and, particularly, awareness of the possibility. The mechanism of injury is stretching and compression of the brachial plexus over a prolonged period. Positioning the patient within the computed tomography (CT) gantry for abdominal or chest procedures can simulate a surgical procedure, particularly when GA is used. The potential for brachial plexus injury is increased if the case is prolonged and the patient's arms are raised above the head to avoid CT image degradation from streak artifacts. We report a case of profound brachial plexus palsy following a CT-guided radiofrequency ablation procedure under GA. Fortunately, the patient recovered completely. We emphasize the mechanism of injury and detail measures to combat this problem, such that radiologists are aware of this potentially serious complication.

  17. Application of the optically stimulated luminescence (OSL) technique for mouse dosimetry in micro-CT imaging

    SciTech Connect (OSTI)

    Vrigneaud, Jean-Marc; Courteau, Alan; Oudot, Alexandra; Collin, Bertrand [Department of Nuclear Medicine, Centre Georges-François Leclerc, 1 rue Professeur Marion, Dijon 21079 Cedex (France)] [Department of Nuclear Medicine, Centre Georges-François Leclerc, 1 rue Professeur Marion, Dijon 21079 Cedex (France); Ranouil, Julien [Landauer Europe, 33 avenue du Général Leclerc, Fontenay-aux-Roses 92266 Cedex (France)] [Landauer Europe, 33 avenue du Général Leclerc, Fontenay-aux-Roses 92266 Cedex (France); Morgand, Loïc; Raguin, Olivier [Oncodesign, 20 rue Jean Mazen, Dijon 21076 Cedex (France)] [Oncodesign, 20 rue Jean Mazen, Dijon 21076 Cedex (France); Walker, Paul [LE2i CNRS UMR 5158, Faculty of Medicine, BP 87900, 21079 Dijon Cedex (France)] [LE2i CNRS UMR 5158, Faculty of Medicine, BP 87900, 21079 Dijon Cedex (France); Brunotte, François [Department of Nuclear Medicine, Centre Georges-François Leclerc, 1 rue Professeur Marion, Dijon 21079 Cedex, France and LE2i CNRS UMR 5158, Faculty of Medicine, BP 87900, 21079 Dijon Cedex (France)] [Department of Nuclear Medicine, Centre Georges-François Leclerc, 1 rue Professeur Marion, Dijon 21079 Cedex, France and LE2i CNRS UMR 5158, Faculty of Medicine, BP 87900, 21079 Dijon Cedex (France)

    2013-12-15T23:59:59.000Z

    Purpose: Micro-CT is considered to be a powerful tool to investigate various models of disease on anesthetized animals. In longitudinal studies, the radiation dose delivered by the micro-CT to the same animal is a major concern as it could potentially induce spurious effects in experimental results. Optically stimulated luminescence dosimeters (OSLDs) are a relatively new kind of detector used in radiation dosimetry for medical applications. The aim of this work was to assess the dose delivered by the CT component of a micro-SPECT (single-photon emission computed tomography)/CT camera during a typical whole-body mouse study, using commercially available OSLDs based on Al{sub 2}O{sub 3}:C crystals.Methods: CTDI (computed tomography dose index) was measured in micro-CT with a properly calibrated pencil ionization chamber using a rat-like phantom (60 mm in diameter) and a mouse-like phantom (30 mm in diameter). OSLDs were checked for reproducibility and linearity in the range of doses delivered by the micro-CT. Dose measurements obtained with OSLDs were compared to those of the ionization chamber to correct for the radiation quality dependence of OSLDs in the low-kV range. Doses to tissue were then investigated in phantoms and cadavers. A 30 mm diameter phantom, specifically designed to insert OSLDs, was used to assess radiation dose over a typical whole-body mouse imaging study. Eighteen healthy female BALB/c mice weighing 27.1 ± 0.8 g (1 SD) were euthanized for small animal measurements. OLSDs were placed externally or implanted internally in nine different locations by an experienced animal technician. Five commonly used micro-CT protocols were investigated.Results: CTDI measurements were between 78.0 ± 2.1 and 110.7 ± 3.0 mGy for the rat-like phantom and between 169.3 ± 4.6 and 203.6 ± 5.5 mGy for the mouse-like phantom. On average, the displayed CTDI at the operator console was underestimated by 1.19 for the rat-like phantom and 2.36 for the mouse-like phantom. OSLDs exhibited a reproducibility of 2.4% and good linearity was found between 60 and 450 mGy. The energy scaling factor was calculated to be between 1.80 ± 0.16 and 1.86 ± 0.16, depending on protocol used. In phantoms, mean doses to tissue over a whole-body CT examination were ranging from 186.4 ± 7.6 to 234.9 ± 7.1 mGy. In mice, mean doses to tissue in the mouse trunk (thorax, abdomen, pelvis, and flanks) were between 213.0 ± 17.0 and 251.2 ± 13.4 mGy. Skin doses (3 OSLDs) were much higher with average doses between 350.6 ± 25.3 and 432.5 ± 34.1 mGy. The dose delivered during a topogram was found to be below 10 mGy. Use of the multimouse bed of the system gave a significantly 20%–40% lower dose per animal (p < 0.05).Conclusions: Absorbed doses in micro-CT were found to be relatively high. In micro-SPECT/CT imaging, the micro-CT unit is mainly used to produce a localization frame. As a result, users should pay attention to adjustable CT parameters so as to minimize the radiation dose and avoid any adverse radiation effects which may interfere with biological parameters studied.

  18. Comparison of MRI-based and CT/MRI fusion-based postimplant dosimetric analysis of prostate brachytherapy

    SciTech Connect (OSTI)

    Tanaka, Osamu [Department of Radiology, Gifu University School of Medicine, Gifu City (Japan)]. E-mail: osa-mu@umin.ac.jp; Hayashi, Shinya [Department of Radiology, Gifu University School of Medicine, Gifu City (Japan); Matsuo, Masayuki [Department of Radiology, Gifu University School of Medicine, Gifu City (Japan); Sakurai, Kota [Department of Radiology, Gifu University School of Medicine, Gifu City (Japan); Department of Urology, Gifu University School of Medicine, Gifu City (Japan); Nakano, Masahiro [Department of Urology, Gifu University School of Medicine, Gifu City (Japan); Maeda, Sunaho [Department of Radiology, Gifu University School of Medicine, Gifu City (Japan); Kajita, Kimihiro R.T. [Department of Radiology, Gifu University School of Medicine, Gifu City (Japan); Deguchi, Takashi [Department of Urology, Gifu University School of Medicine, Gifu City (Japan); Hoshi, Hiroaki [Department of Radiology, Gifu University School of Medicine, Gifu City (Japan)

    2006-10-01T23:59:59.000Z

    Purpose: The aim of this study was to compare the outcomes between magnetic resonance imaging (MRI)-based and computed tomography (CT)/MRI fusion-based postimplant dosimetry methods in permanent prostate brachytherapy. Methods and Materials: Between October 2004 and March 2006, a total of 52 consecutive patients with prostate cancer were treated by brachytherapy, and postimplant dosimetry was performed using CT/MRI fusion. The accuracy and reproducibility were prospectively compared between MRI-based dosimetry and CT/MRI fusion-based dosimetry based on the dose-volume histogram (DVH) related parameters as recommended by the American Brachytherapy Society. Results: The prostate volume was 15.97 {+-} 6.17 cc (mean {+-} SD) in MRI-based dosimetry, and 15.97 {+-} 6.02 cc in CT/MRI fusion-based dosimetry without statistical difference. The prostate V100 was 94.5% and 93.0% in MRI-based and CT/MRI fusion-based dosimetry, respectively, and the difference was statistically significant (p = 0.002). The prostate D90 was 119.4% and 114.4% in MRI-based and CT/MRI fusion-based dosimetry, respectively, and the difference was statistically significant (p = 0.004). Conclusion: Our current results suggested that, as with fusion images, MR images allowed accurate contouring of the organs, but they tended to overestimate the analysis of postimplant dosimetry in comparison to CT/MRI fusion images. Although this MRI-based dosimetric discrepancy was negligible, MRI-based dosimetry was acceptable and reproducible in comparison to CT-based dosimetry, because the difference between MRI-based and CT/MRI fusion-based results was smaller than that between CT-based and CT/MRI fusion-based results as previously reported.

  19. Dynamic cone beam CT angiography of carotid and cerebral arteries using canine model

    SciTech Connect (OSTI)

    Cai Weixing; Zhao Binghui; Conover, David; Liu Jiangkun; Ning Ruola [Department of Imaging Sciences, University of Rochester, 601 Elmwood Avenue, Rochester, New York 14642 (United States); Department of Radiology, Shanghai 6th People's Hospital, 600 Yishan Road, Xuhui, Shanghai (China); Koning Corporation, Lennox Tech Enterprise Center, 150 Lucius Gordon Drive Suite 112, West Henrietta, New York 14586 (United States); Department of Imaging Sciences, University of Rochester, 601 Elmwood Avenue, Rochester, New York 14642 (United States); Department of Imaging Sciences, University of Rochester, 601 Elmwood Avenue, Rochester, New York 14642 (United States) and Koning Corporation, Lennox Tech Enterprise Center, 150 Lucius Gordon Drive Suite 112, West Henrietta, New York 14586 (United States)

    2012-01-15T23:59:59.000Z

    Purpose: This research is designed to develop and evaluate a flat-panel detector-based dynamic cone beam CT system for dynamic angiography imaging, which is able to provide both dynamic functional information and dynamic anatomic information from one multirevolution cone beam CT scan. Methods: A dynamic cone beam CT scan acquired projections over four revolutions within a time window of 40 s after contrast agent injection through a femoral vein to cover the entire wash-in and wash-out phases. A dynamic cone beam CT reconstruction algorithm was utilized and a novel recovery method was developed to correct the time-enhancement curve of contrast flow. From the same data set, both projection-based subtraction and reconstruction-based subtraction approaches were utilized and compared to remove the background tissues and visualize the 3D vascular structure to provide the dynamic anatomic information. Results: Through computer simulations, the new recovery algorithm for dynamic time-enhancement curves was optimized and showed excellent accuracy to recover the actual contrast flow. Canine model experiments also indicated that the recovered time-enhancement curves from dynamic cone beam CT imaging agreed well with that of an IV-digital subtraction angiography (DSA) study. The dynamic vascular structures reconstructed using both projection-based subtraction and reconstruction-based subtraction were almost identical as the differences between them were comparable to the background noise level. At the enhancement peak, all the major carotid and cerebral arteries and the Circle of Willis could be clearly observed. Conclusions: The proposed dynamic cone beam CT approach can accurately recover the actual contrast flow, and dynamic anatomic imaging can be obtained with high isotropic 3D resolution. This approach is promising for diagnosis and treatment planning of vascular diseases and strokes.

  20. Probing Mott lobes via the AC Josephson effect

    E-Print Network [OSTI]

    M. X. Huo; Ying Li; Z. Song; C. P. Sun

    2008-03-04T23:59:59.000Z

    The alternating-current (AC) Josephson effect is studied in a system consisting of two weakly coupled Bose Hubbard models. In the framework of the mean field theory, Gross-Pitaevskii equations show that the amplitude of the Josephson current is proportional to the product of superfluid order parameters. In addition, the chemical potential--current relation for a small size system is obtained via the exact numerical computation. This allows us to propose a feasible experimental scheme to measure the Mott lobes of the quantum phase transition.

  1. Analysis of the Irregular Pulsations of AC Her

    E-Print Network [OSTI]

    Z. Kollath; J. R. Buchler; T. Serre; J. Mattei

    1997-07-08T23:59:59.000Z

    The AAVSO lightcurve data of the irregularly pulsating star AC Herculis of the RV Tau class are analysed. The lightcurve is shown to be incompatible with a periodic, or even multiperiodic pulsation, even if allowance is made for evolution. Instead the best explanation is that the irregularly alternating cycles are a manifestation of low dimensional chaos. The lightcurve is found to be generated by a 3 or 4 dimensional dynamics -- 3 or 4 first order ODEs. The (Lyapunov) fractal dimension of the underlying dynamic attractor is computed to be d_L ~ 2.2, smaller than the value of d_L ~ 3.1 found for R Sct.

  2. Radiation dose reduction in medical CT through equally sloped tomography Benjamin P. Fahimian1,2,6

    E-Print Network [OSTI]

    Soatto, Stefano

    Council on Radiation Protection & Measurements10 , CT accounts for about 15% of the total radiological50Radiation dose reduction in medical CT through equally sloped tomography Benjamin P. Fahimian1 Department of Radiation Oncology, Stanford University, Stanford, CA 94305 3 Biomedical Physics

  3. A method for measuring joint kinematics designed for accurate registration of kinematic data to models constructed from CT data

    E-Print Network [OSTI]

    Fischer, Kenneth J.; Manson, T. T.; Pfaeffle, H. J.; Tomaino, M. M.; Woo, S. L-Y

    2001-03-01T23:59:59.000Z

    for position and 0.1 degrees for orientation for linkage digitization and better than +/- 0.2 mm and +/- 0.2 degrees for CT digitization. Surface models of the radius and ulna were constructed from CT data, as an example application. Kinematics of the bones...

  4. USPSTF Recommends Low-Dose CT Screening for Heavy Smoke Published on Cancer Network (http://www.cancernetwork.com)

    E-Print Network [OSTI]

    Serfling, Robert

    remains the leading cause of cancer death in the United States, and is the third most common of all radiography, and found an overall reduction in death from any cause in the CT group of 6.7% (95% CI, 1, lie largely in the high rates of false positives. A total of 96.4% of the positive low-dose CT results

  5. 2002 IEEE NSS/MIC pCT: Hartmut F.-W. Sadrozinski , SCIPP Towards Proton Computed Tomography

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    2002 IEEE NSS/MIC pCT: Hartmut F.-W. Sadrozinski , SCIPP SCIPPSCIPP Towards Proton Computed Tomography L. R. Johnson, B. Keeney, G. Ross, H. F.-W. Sadrozinski, A. Seiden, D.C. Williams, L. Zhang Santa Radiography MC Study #12;2002 IEEE NSS/MIC pCT: Hartmut F.-W. Sadrozinski , SCIPP SCIPPSCIPP Computed

  6. Manifold Learning for 4D CT Reconstruction of the Lung Manfred Georg*, Richard Souvenir, Andrew Hope, Robert Pless*

    E-Print Network [OSTI]

    Pless, Robert

    Manifold Learning for 4D CT Reconstruction of the Lung Manfred Georg*, Richard Souvenir, Andrew, Canada Andrew.Hope@rmp.uhn.on.ca Abstract Computed Tomography is used to create models of lung dynamics because it provides high contrast images of lung tissue. Creating 4D CT models which capture dynamics

  7. 4500. Nasch, P.M., M.H. Manghnani, and R.A. Secco, 1997, Anomalous behavior of sound velocity and attenuation in liquid Fe-Ni-S, Science, 277, 219-221.

    E-Print Network [OSTI]

    4500. Nasch, P.M., M.H. Manghnani, and R.A. Secco, 1997, Anomalous behavior of sound velocityForschungsZentrum, Potsdam, Germany, 6-16. 4502. Blewett, D.T., P.G. Lucey, and B.R. Hawke, 1997, Clementine images., 132, 119-132. 4504. Yu, Z.-P., P.-S. Chu, and T. Schroeder, 1997, Predictive skills of seasonal

  8. A Generalized Class of Stationary Frame-Current Controllers for Grid-Connected AC–DC Converters

    E-Print Network [OSTI]

    Hwang, J. George

    Within power systems, high-power pulsewidth-modulated ac-dc converters are used in flexible ac transmission systems controllers and for interfacing renewable energy sources to the grid. These converters traditionally ...

  9. For information on current fee levels, see: www.strath.ac.uk/registry/students/finance

    E-Print Network [OSTI]

    Mottram, Nigel

    Fees For information on current fee levels, see: www.strath.ac.uk/registry/students/finance How Enquiries can be made to either of the following in the Department of Accounting & Finance: Professor Dick Davies Course Director, Investment & Finance t: +44 (0)141 548 3710 e: jr.davies@strath.ac.uk Barbara

  10. Contract Number: DE-AC05-76RL01830 Modification M881

    E-Print Network [OSTI]

    Contract Number: DE-AC05-76RL01830 Modification M881 B-i Part I ­ The Schedule Section B Supplies.......................................................1 #12;Contract Number: DE-AC05-76RL01830 Modification M881 B-1 B­1 Designation of Work) [M881] B­3 Estimated Fee Base and Total Available Performance Fees In FY12, the total available

  11. Lurching towards markets for power: China's electricity policy 19852007 Xiaoli Zhao a,c,

    E-Print Network [OSTI]

    Lyon, Thomas P.

    Institute for Low Carbon Economy and Trade, North China Electric Power University, Beijing, China a r t i cLurching towards markets for power: China's electricity policy 1985­2007 Xiaoli Zhao a,c, , Thomas P. Lyon b , Cui Song a,c a School of Economics and Management, North China Electric Power University

  12. Bone Motion Analysis From Dynamic MRI: Ac-quisition and Tracking

    E-Print Network [OSTI]

    Gilles, Benjamin

    of mechanical overload, impingement or femoral head instability. For both diagnosis and surgical planning, an acBone Motion Analysis From Dynamic MRI: Ac- quisition and Tracking INTRODUCTION Periacetabular- curate estimate of hip joint bone motion is required. Orthopedists can use animated 3D models, prior

  13. Control of Parallel-Connected Bidirectional AC-DC Converters in Stationary Frame for Microgrid

    E-Print Network [OSTI]

    Teodorescu, Remus

    Sistemes Automàtica i Informàtica Industrial Universitat Politècnica de Catalunya Abstract. In this paper, parallel-connected bidirectional converters for AC and DC hybrid microgrid application energy sources [3-6]. A hybrid microgrid can be made up of distributed renewable source, AC and DC common

  14. 80 IAEI NEWS May . June 2012 www.iaei.org Microinverters and ac Pv Modules

    E-Print Network [OSTI]

    Johnson, Eric E.

    and code require- ments. However, they are different from the typical PV string inverters that use multiple80 IAEI NEWS May . June 2012 www.iaei.org Microinverters and ac Pv Modules M icroinverters and AC PV modules are becom- ing very common in residential and small commercial PV systems. See photos 1

  15. Time-Resolved Magnetic Flux and AC-Current Distributions in Superconducting YBCO Thin Films and

    E-Print Network [OSTI]

    Shaw, Leah B.

    Time-Resolved Magnetic Flux and AC-Current Distributions in Superconducting YBCO Thin Films magnetic field. We study the interaction behavior of YBCO thin films in an ac transport current and a dc the calibrated field profiles. The current density evolution in YBCO thin films is studied by TRMOI as a function

  16. DNA MOLECULAR WIRE-BASED NANOELECTRONICS: NEW INSIGHT AND HIGH FREQUENCY AC ELECTRICAL

    E-Print Network [OSTI]

    Kassegne, Samuel Kinde

    DNA MOLECULAR WIRE-BASED NANOELECTRONICS: NEW INSIGHT AND HIGH FREQUENCY AC ELECTRICAL the Thesis of Denni Ari Wibowo: DNA Molecular Wire-Based Nanoelectronics: New Insight and High Frequency AC alone. #12;v ABSTRACT OF THE THESIS DNA Molecular Wire-Based Nanoelectronics: New Insight and High

  17. The Hybrid Power Flow Controller A New Concept for Flexible AC Transmission

    E-Print Network [OSTI]

    Lehn, Peter W.

    large and costly projects. Over the years, environmental, right­of­way, and cost prob- lems have delayedThe Hybrid Power Flow Controller A New Concept for Flexible AC Transmission Jovan Z. Bebic Electric flow controller topologies are proposed for flexible AC transmission systems (FACTS). The first one

  18. Ultrafast high-pressure AC electro-osmotic pumps for portable biomedical microfluidics

    E-Print Network [OSTI]

    Bazant, Martin Z.

    Ultrafast high-pressure AC electro-osmotic pumps for portable biomedical microfluidics Chien details the development of an integrated AC electro-osmotic (ACEO) microfluidic pump for dilute (100 mM) biological solutions in separate microfluidic devices, with potential applications in portable

  19. Dumbarton Express Line DB heading to Stanford Oval. AC Transit Line U on Palm Drive.

    E-Print Network [OSTI]

    Dumbarton Express Line DB heading to Stanford Oval. AC Transit Line U on Palm Drive. Photo: Karl Nielsen Photo: Dong Wang Schedules: AC Transit Line U Dumbarton Express Line DB Connections with BART Transit Line U Line U provides express service between Stanford and the Fremont BART station. Other East

  20. * jafleeman@aep.com EHV AC and HVDC Transmission Working Together to Integrate Renewable Power

    E-Print Network [OSTI]

    McCalley, James D.

    * jafleeman@aep.com EHV AC and HVDC Transmission Working Together to Integrate Renewable Power J. A current (EHV AC) and high voltage direct current (HVDC) transmission systems and advocates a hybrid as a high capacity platform for system integration. HVDC transmission offers express, efficient delivery

  1. Fabrication of Superhydrophobic Fiber Coatings by DC-Biased AC-Electrospinning

    E-Print Network [OSTI]

    Tafreshi, Hooman Vahedi

    Fabrication of Superhydrophobic Fiber Coatings by DC-Biased AC-Electrospinning Fredrick O. Ochanda DC-biased AC-electrospinning. Superhydrophobic surfaces with water contact angles greater than 150 on superhydrophobicity. VC 2011 Wiley Periodicals, Inc. J Appl Polym Sci 123: 1112­1119, 2012 Key words: superhydrophobic

  2. Fabrication of Superhydrophobic Fiber Coatings by DC-Biased AC-Electrospinning

    E-Print Network [OSTI]

    Tafreshi, Hooman Vahedi

    Fabrication of Superhydrophobic Fiber Coatings by DC-Biased AC-Electrospinning Fredrick O. Ochanda DC-biased AC-electrospinning. Superhydrophobic surfaces with water contact angles greater than 150 Superhydrophobicity is achieved by combining nano- or microscale roughness with a low-surface free energy material

  3. Does dual-energy CT of lower-extremity tendons incur penalties in patient radiation exposure or reduced multiplanar reconstruction image quality?

    E-Print Network [OSTI]

    2008-01-01T23:59:59.000Z

    diagnostic value of dual-energy CT and MRI in the detectionusing dual-source dual-energy MDCT: Results of JAFROCfor dose reduction in dual energy hepatic CT using non-

  4. Multimodal Vessel Visualization of Mouse Aorta PET/CT Scans Timo Ropinski, Member, IEEE, Sven Hermann, Rainer Reich, Michael Schafers, and Klaus Hinrichs, Member, IEEE

    E-Print Network [OSTI]

    Hinrichs, Klaus

    Multimodal Vessel Visualization of Mouse Aorta PET/CT Scans Timo Ropinski, Member, IEEE, Sven present a visualization system for the visual analysis of PET/CT scans of aortic arches of mice

  5. Concurrent segmentation of the prostate on MRI and CT via linked statistical shape models for radiotherapy planning

    SciTech Connect (OSTI)

    Chowdhury, Najeeb; Toth, Robert; Chappelow, Jonathan; Kim, Sung; Motwani, Sabin; Punekar, Salman; Lin Haibo; Both, Stefan; Vapiwala, Neha; Hahn, Stephen; Madabhushi, Anant

    2012-04-15T23:59:59.000Z

    Purpose: Prostate gland segmentation is a critical step in prostate radiotherapy planning, where dose plans are typically formulated on CT. Pretreatment MRI is now beginning to be acquired at several medical centers. Delineation of the prostate on MRI is acknowledged as being significantly simpler to perform, compared to delineation on CT. In this work, the authors present a novel framework for building a linked statistical shape model (LSSM), a statistical shape model (SSM) that links the shape variation of a structure of interest (SOI) across multiple imaging modalities. This framework is particularly relevant in scenarios where accurate boundary delineations of the SOI on one of the modalities may not be readily available, or difficult to obtain, for training a SSM. In this work the authors apply the LSSM in the context of multimodal prostate segmentation for radiotherapy planning, where the prostate is concurrently segmented on MRI and CT. Methods: The framework comprises a number of logically connected steps. The first step utilizes multimodal registration of MRI and CT to map 2D boundary delineations of the prostate from MRI onto corresponding CT images, for a set of training studies. Hence, the scheme obviates the need for expert delineations of the gland on CT for explicitly constructing a SSM for prostate segmentation on CT. The delineations of the prostate gland on MRI and CT allows for 3D reconstruction of the prostate shape which facilitates the building of the LSSM. In order to perform concurrent prostate MRI and CT segmentation using the LSSM, the authors employ a region-based level set approach where the authors deform the evolving prostate boundary to simultaneously fit to MRI and CT images in which voxels are classified to be either part of the prostate or outside the prostate. The classification is facilitated by using a combination of MRI-CT probabilistic spatial atlases and a random forest classifier, driven by gradient and Haar features. Results: The authors acquire a total of 20 MRI-CT patient studies and use the leave-one-out strategy to train and evaluate four different LSSMs. First, a fusion-based LSSM (fLSSM) is built using expert ground truth delineations of the prostate on MRI alone, where the ground truth for the gland on CT is obtained via coregistration of the corresponding MRI and CT slices. The authors compare the fLSSM against another LSSM (xLSSM), where expert delineations of the gland on both MRI and CT are employed in the model building; xLSSM representing the idealized LSSM. The authors also compare the fLSSM against an exclusive CT-based SSM (ctSSM), built from expert delineations of the gland on CT alone. In addition, two LSSMs trained using trainee delineations (tLSSM) on CT are compared with the fLSSM. The results indicate that the xLSSM, tLSSMs, and the fLSSM perform equivalently, all of them out-performing the ctSSM. Conclusions: The fLSSM provides an accurate alternative to SSMs that require careful expert delineations of the SOI that may be difficult or laborious to obtain. Additionally, the fLSSM has the added benefit of providing concurrent segmentations of the SOI on multiple imaging modalities.

  6. Cost vs. performance ... Gwyn Griffiths email: gxg@noc.soton.ac.uk http://www.noc.soton.ac.uk/OED/gxg/

    E-Print Network [OSTI]

    Griffiths, Gwyn

    and safety-related costs are estimated to be 25% of the cost of the capital items. End of life disposal cost will be 5% of the capital cost. #12;Cost vs. performance ... Gwyn Griffiths email: gxg@noc.soton.ac.uk http://www.noc.soton.ac.uk/OED/gxg/ Cost & performance of Li-Po secondary batteries Component Capital cost Amortised cost per kWh Cost per

  7. SU-E-J-86: Lobar Lung Function Quantification by PET Galligas and CT Ventilation Imaging in Lung Cancer Patients

    SciTech Connect (OSTI)

    Eslick, E; Kipritidis, J; Keall, P [University of Sydney, Camperdown, NSW (Australia); Bailey, D; Bailey, E [Royal North Shore Hospital, St. Leonards, NSW (Australia)

    2014-06-01T23:59:59.000Z

    Purpose: The purpose of this study was to quantify the lobar lung function using the novel PET Galligas ([68Ga]-carbon nanoparticle) ventilation imaging and the investigational CT ventilation imaging in lung cancer patients pre-treatment. Methods: We present results on our first three lung cancer patients (2 male, mean age 78 years) as part of an ongoing ethics approved study. For each patient a PET Galligas ventilation (PET-V) image and a pair of breath hold CT images (end-exhale and end-inhale tidal volumes) were acquired using a Siemens Biograph PET CT. CT-ventilation (CT-V) images were created from the pair of CT images using deformable image registration (DIR) algorithms and the Hounsfield Unit (HU) ventilation metric. A comparison of ventilation quantification from each modality was done on the lobar level and the voxel level. A Bland-Altman plot was used to assess the difference in mean percentage contribution of each lobe to the total lung function between the two modalities. For each patient, a voxel-wise Spearmans correlation was calculated for the whole lungs between the two modalities. Results: The Bland-Altman plot demonstrated strong agreement between PET-V and CT-V for assessment of lobar function (r=0.99, p<0.001; range mean difference: ?5.5 to 3.0). The correlation between PET-V and CT-V at the voxel level was moderate(r=0.60, p<0.001). Conclusion: This preliminary study on the three patients data sets demonstrated strong agreement between PET and CT ventilation imaging for the assessment of pre-treatment lung function at the lobar level. Agreement was only moderate at the level of voxel correlations. These results indicate that CT ventilation imaging has potential for assessing pre-treatment lobar lung function in lung cancer patients.

  8. COUNTRY INSTITUTION DATE WEB ADDRESS IRAN University of Art Isfahn 08.03.2007 http://www.aui.ac.ir

    E-Print Network [OSTI]

    Di Pillo, Gianni

    COUNTRY INSTITUTION DATE WEB ADDRESS IRAN University of Art Isfahn 08.03.2007 http://www.aui.ac.ir IRAN Isfahn University of Technology 08.03.2007 http://www.iut.ac.ir IRAN The University of Isfahn 15/03/2011 http://www.ui.ac.ir IRAN Shahid Bahonar University of Kermn 06.06.2005 http

  9. Soft Tissue Visualization Using a Highly Efficient Megavoltage Cone Beam CT Imaging System

    E-Print Network [OSTI]

    Pouliot, Jean

    Soft Tissue Visualization Using a Highly Efficient Megavoltage Cone Beam CT Imaging System Farhad A developed an imaging system that is optimized for MV and can acquire Megavoltage CBCT images containing soft through the detector. #12;The ability of an x-ray imaging system to differentiate soft tissues is affected

  10. Lobe-based Estimating Ventilation and Perfusion from 3D CT scans of the Lungs

    E-Print Network [OSTI]

    Warren, Joe

    Lobe-based Estimating Ventilation and Perfusion from 3D CT scans of the Lungs Travis McPhail Joe are the ventilation (air flow) and perfusion (blood flow) in the patient's lungs. Given the flow of air and blood as possible. The current state of the art technology for assessing the ventilation in a patient's lungs

  11. CLASSIFICATION OF BIOMEDICAL HIGH-RESOLUTION MICRO-CT IMAGES FOR DIRECT VOLUME RENDERING

    E-Print Network [OSTI]

    López-Sánchez, Maite

    CLASSIFICATION OF BIOMEDICAL HIGH-RESOLUTION MICRO-CT IMAGES FOR DIRECT VOLUME RENDERING Maite L,cerquide,davidm,anna}@maia.ub.es ABSTRACT This paper introduces a machine learning approach into the process of direct volume rendering that generates the classification func- tion within the optical property function used for rendering. Briefly

  12. The feasibility of head motion tracking in helical CT: A step toward motion correction

    SciTech Connect (OSTI)

    Kim, Jung-Ha [Medical Radiation Sciences, University of Sydney, NSW 2141 (Australia); Nuyts, Johan [Department of Nuclear Medicine, Katholieke Universiteit, Leuven, Belgium and Medical Imaging Research Center, Katholieke Universiteit, Leuven (Belgium); Kuncic, Zdenka [School of Physics, University of Sydney, NSW 2006 (Australia); Fulton, Roger [Medical Radiation Sciences, University of Sydney, NSW 2141 (Australia); School of Physics, University of Sydney, NSW 2006 (Australia); Department of Medical Physics, Westmead Hospital, Westmead, NSW 2145 (Australia)

    2013-04-15T23:59:59.000Z

    Purpose: To establish a practical and accurate motion tracking method for the development of rigid motion correction methods in helical x-ray computed tomography (CT). Methods: A commercially available optical motion tracking system provided 6 degrees of freedom pose measurements at 60 Hz. A 4 Multiplication-Sign 4 calibration matrix was determined to convert raw pose data acquired in tracker coordinates to a fixed CT coordinate system with origin at the isocenter of the scanner. Two calibration methods, absolute orientation (AO), and a new method based on image registration (IR), were compared by means of landmark analysis and correlation coefficient in phantom images coregistered using the derived motion transformations. Results: Transformations calculated using the IR-derived calibration matrix were found to be more accurate, with positional errors less than 0.5 mm (mean RMS), and highly correlated image voxel intensities. The AO-derived calibration matrix yielded larger mean RMS positional errors ( Asymptotically-Equal-To 1.0 mm), and poorer correlation coefficients. Conclusions: The authors have demonstrated the feasibility of accurate motion tracking for retrospective motion correction in helical CT. Their new IR-based calibration method based on image registration and function minimization was simpler to perform and delivered more accurate calibration matrices. This technique is a useful tool for future work on rigid motion correction in helical CT and potentially also other imaging modalities.

  13. Hydro-thermal flow in a rough fracture EC Contract SES6-CT-2003-502706

    E-Print Network [OSTI]

    Schmittbuhl, Jean

    Hydro-thermal flow in a rough fracture EC Contract SES6-CT-2003-502706 PARTICIPANT ORGANIZATION NAME: CNRS Synthetic 2nd year report Related with Work Package............ HYDRO-THERMAL FLOW in the influence of a realistic geometry of the fracture on its hydro-thermal response. Several studies have

  14. Interactive Separation of Segmented Bones in CT Volumes Using Graph Cut

    E-Print Network [OSTI]

    Ju, Tao

    mask customized to the shape of the bone, such as the femoral head. However, creat- ing masks for bones of different methodology have been reported for bone segmen- tation (see a recent survey in [1]). DueInteractive Separation of Segmented Bones in CT Volumes Using Graph Cut Lu Liu, David Raber, David

  15. DAWN: A JOURNEY TO THE BEGINNING OF THE SOLAR SYSTEM C.T. Russell(1)

    E-Print Network [OSTI]

    Zuber, Maria

    -ray/neutron spectrometer, a magnetometer and a gravity investigation. Dawn uses solar arrays to power its xenon ion engine solar panels roughly 21 m tip-to-tip, a 5 m magnetometer boom and three ion thrusters, one of whichDAWN: A JOURNEY TO THE BEGINNING OF THE SOLAR SYSTEM C.T. Russell(1) , A. Coradini(2) , W

  16. Lee, C-T A Laser Ablation Data Reduction 2006 LASER ABLATION ICP-MS: DATA

    E-Print Network [OSTI]

    Lee, Cin-Ty Aeolus

    Lee, C-T A Laser Ablation Data Reduction 2006 1 LASER ABLATION ICP-MS: DATA REDUCTION Cin-Ty A. Lee 24 September 2006 Analysis and calculation of concentrations Laser ablation analyses are done in time by turning on the laser and ablating the sample, generating a time-dependent signal (Fig. 1). Measurements

  17. jCT: A Java Code Tomograph Markus Lumpe, Samiran Mahmud, and Olga Goloshchapova

    E-Print Network [OSTI]

    Lumpe, Markus

    jCT: A Java Code Tomograph Markus Lumpe, Samiran Mahmud, and Olga Goloshchapova Faculty,smahmud,ogoloshchapova}@swin.edu.au Abstract--We are concerned with analyzing software, in par- ticular, with its nature and how developer software engineering where measurement seeks to capture attributes affecting the product, process

  18. SCIPP 06/04 1 Prototype Tracking Studies for Proton CT

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    SCIPP 06/04 1 Prototype Tracking Studies for Proton CT Nate Blumenkrantz, Jason Feldt, Jason the feasibility of proton computed tomography, the most likely path (MLP) of protons inside an absorber resolution. The locations of 200 MeV protons were measured at three different absorber depth of PMMA (3.75, 6

  19. Development of a proton Computed Tomography (pCT) scanner at NIU

    E-Print Network [OSTI]

    Uzunyan, S A; Boi, S; Coutrakon, G; Dyshkant, A; Erdelyi, B; Gearhart, A; Hedin, D; Johnson, E; Krider, J; Zutshi, V; Ford, R; Fitzpatrick, T; Sellberg, G; Rauch, J E; Roman, M; Rubinov, P; Wilson, P; Lalwani, K; Naimuddin, M

    2013-01-01T23:59:59.000Z

    We describe the development of a proton Computed Tomography (pCT) scanner at Northern Illinois University (NIU) in collaboration with Fermilab and Delhi University. This paper provides an overview of major components of the scanner and a detailed description of the data acquisition system (DAQ).

  20. Development of a proton Computed Tomography (pCT) scanner at NIU

    E-Print Network [OSTI]

    S. A. Uzunyan; G. Blazey; S. Boi; G. Coutrakon; A. Dyshkant; B. Erdelyi; A. Gearhart; D. Hedin; E. Johnson; J. Krider; V. Zutshi; R. Ford; T. Fitzpatrick; G. Sellberg; J. E. Rauch; M. Roman; P. Rubinov; P. Wilson; K. Lalwani; M. Naimuddin

    2013-12-13T23:59:59.000Z

    We describe the development of a proton Computed Tomography (pCT) scanner at Northern Illinois University (NIU) in collaboration with Fermilab and Delhi University. This paper provides an overview of major components of the scanner and a detailed description of the data acquisition system (DAQ).

  1. Surface Extraction from Multi-Material Components for Metrology using Dual Energy CT

    E-Print Network [OSTI]

    materials (e.g., carbon-fibre-reinforced plas- tics) induce manufacturers to design new functionSurface Extraction from Multi-Material Components for Metrology using Dual Energy CT Christoph surface models of multi-material components using dual energy com- puted tomography (DECT

  2. Toxoplasma encephalitis in Haitian adults with acquired immunodeficiency syndrome: a clinical-pathologic-CT correlation

    SciTech Connect (OSTI)

    Post, M.J.D.; Chan, J.C.; Hensley, G.T.; Hoffman, T.A.; Moskowitz, L.B.; Lippmann, S.

    1983-05-01T23:59:59.000Z

    The clinical data, histologic findings, and computed tomographic (CT) abnormalities in eight adult Haitians with toxoplasma encephalitis were analyzed retrospectively. Diagnosis was established by identification of Toxoplasma gondii on autopsy in five and brain biopsy in three specimens and subsequently confirmed by the immunoperoxidase method. All these patiens, six of whom had been in the United States for 24 months or less, had severe idiopathic immunodeficiency syndrome. All were lymphopenic and six were on treatment for tuberculosis when the toxoplasma encephalitis developed. All patients were studied with CT when they developed an altered mental status and fever associated with seizures and/or focal neurologic deficits. Scans before treatment showed multiple intraparenchymal lesions in seven and a single lesion in the thalamus in one. Ring and/or nodular enhancement of the lesions was found in six and hypodense areas in two. Progressions of abnormalities occurred on serial studies. These CT findings that were best shown on axial and coronal thin-section double-dose contrast studies were useful but not diagnostically pathognomonic. In patients with similar clinical presentation CT is recommended to identify focal areas of involvement and to guide brain biopsy or excision so that prompt medical thereapy of this often lethal infection can be instituted.

  3. Multi-stage Learning for Robust Lung Segmentation in Challenging CT Volumes

    E-Print Network [OSTI]

    Multi-stage Learning for Robust Lung Segmentation in Challenging CT Volumes Michal Sofka1 , Jens Imaging, Siemens Healthcare, Oxford, UK Abstract. Simple algorithms for segmenting healthy lung parenchyma an ini- tialization of a statistical shape model of the lungs. The initialization first detects

  4. Technical Reports Ultra-low Dose Lung CT Perfusion Regularized by

    E-Print Network [OSTI]

    Virginia Tech

    Technical Reports Ultra-low Dose Lung CT Perfusion Regularized by a Previous Scan1 Hengyong Yu, Ph­regularized reconstruction (PSRR) method was proposed to reduce radiation dose and applied to lung perfusion studies. Normal and ultra-low-dose lung computed tomographic perfusion studies were compared in terms of the estimation

  5. A Framework for Automatic Segmentation of Lung Nodules from Low Dose Chest CT Scans

    E-Print Network [OSTI]

    Farag, Aly A.

    A Framework for Automatic Segmentation of Lung Nodules from Low Dose Chest CT Scans Ayman El-Baz1 the high accuracy of the proposed approach. 1 Introduction Because lung cancer is the most common cause 1, an initial LDCT slice is segmented with our algorithms introduced in [3] to isolate lung tissues

  6. Volume Estimation and Surgery Planning from Lung CT Images ANA ELISA FERREIRA SCHMIDT

    E-Print Network [OSTI]

    Volume Estimation and Surgery Planning from Lung CT Images ANA ELISA FERREIRA SCHMIDT 1 , PAULO to assist the planning of lung reduction surgeries, a technique that has been proposed for the treatment of certain illnesses. Doctors need to decide which portions of the lungs to remove to achieve a certain

  7. Automatic Lung Segmentation of Volumetric Low-Dose CT Scans Using Graph Cuts

    E-Print Network [OSTI]

    Farag, Aly A.

    Automatic Lung Segmentation of Volumetric Low-Dose CT Scans Using Graph Cuts Asem M. Ali and Aly A for unsupervised segmentation of the lung region from low dose computed tomography (LDCT) images. We follow distribution model. To better spec- ify region borders between lung and chest, each empirical distribution

  8. Statistical model based iterative reconstruction (MBIR) in clinical CT systems: Experimental assessment of noise performance

    SciTech Connect (OSTI)

    Li, Ke; Tang, Jie [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 (United States)] [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 (United States); Chen, Guang-Hong, E-mail: gchen7@wisc.edu [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 and Department of Radiology, University of Wisconsin-Madison, 600 Highland Avenue, Madison, Wisconsin 53792 (United States)] [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 and Department of Radiology, University of Wisconsin-Madison, 600 Highland Avenue, Madison, Wisconsin 53792 (United States)

    2014-04-15T23:59:59.000Z

    Purpose: To reduce radiation dose in CT imaging, the statistical model based iterative reconstruction (MBIR) method has been introduced for clinical use. Based on the principle of MBIR and its nonlinear nature, the noise performance of MBIR is expected to be different from that of the well-understood filtered backprojection (FBP) reconstruction method. The purpose of this work is to experimentally assess the unique noise characteristics of MBIR using a state-of-the-art clinical CT system. Methods: Three physical phantoms, including a water cylinder and two pediatric head phantoms, were scanned in axial scanning mode using a 64-slice CT scanner (Discovery CT750 HD, GE Healthcare, Waukesha, WI) at seven different mAs levels (5, 12.5, 25, 50, 100, 200, 300). At each mAs level, each phantom was repeatedly scanned 50 times to generate an image ensemble for noise analysis. Both the FBP method with a standard kernel and the MBIR method (Veo{sup ®}, GE Healthcare, Waukesha, WI) were used for CT image reconstruction. Three-dimensional (3D) noise power spectrum (NPS), two-dimensional (2D) NPS, and zero-dimensional NPS (noise variance) were assessed both globally and locally. Noise magnitude, noise spatial correlation, noise spatial uniformity and their dose dependence were examined for the two reconstruction methods. Results: (1) At each dose level and at each frequency, the magnitude of the NPS of MBIR was smaller than that of FBP. (2) While the shape of the NPS of FBP was dose-independent, the shape of the NPS of MBIR was strongly dose-dependent; lower dose lead to a “redder” NPS with a lower mean frequency value. (3) The noise standard deviation (?) of MBIR and dose were found to be related through a power law of ????(dose){sup ??} with the component ? ? 0.25, which violated the classical ????(dose){sup ?0.5} power law in FBP. (4) With MBIR, noise reduction was most prominent for thin image slices. (5) MBIR lead to better noise spatial uniformity when compared with FBP. (6) A composite image generated from two MBIR images acquired at two different dose levels (D1 and D2) demonstrated lower noise than that of an image acquired at a dose level of D1+D2. Conclusions: The noise characteristics of the MBIR method are significantly different from those of the FBP method. The well known tradeoff relationship between CT image noise and radiation dose has been modified by MBIR to establish a more gradual dependence of noise on dose. Additionally, some other CT noise properties that had been well understood based on the linear system theory have also been altered by MBIR. Clinical CT scan protocols that had been optimized based on the classical CT noise properties need to be carefully re-evaluated for systems equipped with MBIR in order to maximize the method's potential clinical benefits in dose reduction and/or in CT image quality improvement.

  9. Enlarged longitudinal dose profiles in cone-beam CT and the need for modified dosimetry

    SciTech Connect (OSTI)

    Mori, Shinichiro; Endo, Masahiro; Nishizawa, Kanae; Tsunoo, Takanori; Aoyama, Takahiko; Fujiwara, Hideaki; Murase, Kenya [National Institute of Radiological Sciences, Chiba 263-8555 (Japan); School of Health Sciences, Nagoya University, Nagoya 461-8673 (Japan); School of Allied Health Sciences, Faculty of Medicine, Osaka University, Osaka 565-0871 (Japan)

    2005-04-01T23:59:59.000Z

    In order to examine phantom length necessary to assess radiation dose delivered to patients in cone-beam CT with an enlarged beamwidth, we measured dose profiles in cylindrical phantoms of sufficient length using a prototype 256-slice CT-scanner developed at our institute. Dose profiles parallel to the rotation axis were measured at the central and peripheral positions in PMMA (polymethylmethacrylate) phantoms of 160 or 320 mm diameter and 900 mm length. For practical application, we joined unit cylinders (150 mm long) together to provide phantoms of 900 mm length. Dose profiles were measured with a pin photodiode sensor having a sensitive region of approximately 2.8x2.8 mm{sup 2} and 2.7 mm thickness. Beamwidths of the scanner were varied from 20 to 138 mm. Dose profile integrals (DPI) were calculated using the measured dose profiles for various beamwidths and integration ranges. For the body phantom (320-mm-diam phantom), 76% of the DPI was represented for a 20 mm beamwidth and 60% was represented for a 138 mm beamwidth if dose profiles were integrated over a 100 mm range, while more than 90% of the DPI was represented for beamwidths between 20 and 138 mm if integration was carried out over a 300 mm range. The phantom length and integration range for dosimetry of cone-beam CT needed to be more than 300 mm to represent more than 90% of the DPI for the body phantom with the beamwidth of more than 20 mm. Although we reached this conclusion using the prototype 256-slice CT-scanner, it may be applied to other multislice CT-scanners as well.

  10. Comparison of Fusion Imaging Using a Combined SPECT/CT System and Intra-arterial CT: Assessment of Drug Distribution by an Implantable Port System in Patients Undergoing Hepatic Arterial Infusion Chemotherapy

    SciTech Connect (OSTI)

    Ikeda, Osamu, E-mail: osamu-3643ik@do9.enjoy.ne.jp; Kusunoki, Shinichiroh; Nakaura, Takeshi; Shiraishi, Shinya; Kawanaka, Kouichi; Tomiguchi, Seiji; Yamashita, Yasuyuki [Kumamoto University Graduate School of Medical and Pharmaceutical Sciences, Department of Diagnostic Radiology (Japan); Takamori, Hiroshi; Chikamoto, Akira; Kanemitsu, Keiichiro [Kumamoto University Graduate School of Medical and Pharmaceutical Sciences, Gastroenterological Surgery (Japan)

    2006-06-15T23:59:59.000Z

    Hepatic arterial infusion (HAI) chemotherapy is effective for treating primary and metastatic carcinoma of the liver. We compared the perfusion patterns of HAI chemotherapy on intra-arterial port-catheter computed tomography (iapc-CT) and fused images obtained with a combined single-photon emission computed tomography/computed tomography (SPECT/CT) system. We studied 28 patients with primary or metastatic carcinoma of the liver who bore an implantable HAI port system. All underwent abdominal SPECT using Tc-99m-MAA (185 Mbq); the injection rate was 1 mL/min, identical to the chemotherapy infusion rate, and 0.5 mL/sec for iapc-CT. Delivery was through an implantable port. We compared the intrahepatic perfusion (IHP) and extrahepatic perfusion (EHP) patterns of HAI chemotherapy on iapc-CT images and fused images obtained with a combined SPECT/CT system. In 23 of 28 patients (82%), IHP patterns on iapc-CT images and fused images were identical. In 5 of the 28 patients (18%), IHP on fusion images was different from IHP on iapc-CT images. EHP was seen on fused images in 12 of the 28 patients (43%) and on iapc-CT images in 8 patients (29%). In 17 patients (61%), upper gastrointestinal endoscopy revealed gastroduodenal mucosal lesions. EHP was revealed on fused images in 10 of these patients; 9 of them manifested gastroduodenal toxicity at the time of subsequent HAI chemotherapy. Fusion imaging using the combined SPECT/CT system reflects the actual distribution of the infused anticancer agent. This information is valuable not only for monitoring adequate drug distribution but also for avoiding potential extrahepatic complications.

  11. Reconstruction of a time-averaged midposition CT scan for radiotherapy planning of lung cancer patients using deformable registration

    SciTech Connect (OSTI)

    Wolthaus, J. W. H.; Sonke, J.-J.; Herk, M. van; Damen, E. M. F. [Department of Radiation Oncology, Netherlands Cancer Institute-Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands)

    2008-09-15T23:59:59.000Z

    Purpose: lower lobe lung tumors move with amplitudes of up to 2 cm due to respiration. To reduce respiration imaging artifacts in planning CT scans, 4D imaging techniques are used. Currently, we use a single (midventilation) frame of the 4D data set for clinical delineation of structures and radiotherapy planning. A single frame, however, often contains artifacts due to breathing irregularities, and is noisier than a conventional CT scan since the exposure per frame is lower. Moreover, the tumor may be displaced from the mean tumor position due to hysteresis. The aim of this work is to develop a framework for the acquisition of a good quality scan representing all scanned anatomy in the mean position by averaging transformed (deformed) CT frames, i.e., canceling out motion. A nonrigid registration method is necessary since motion varies over the lung. Methods and Materials: 4D and inspiration breath-hold (BH) CT scans were acquired for 13 patients. An iterative multiscale motion estimation technique was applied to the 4D CT scan, similar to optical flow but using image phase (gray-value transitions from bright to dark and vice versa) instead. From the (4D) deformation vector field (DVF) derived, the local mean position in the respiratory cycle was computed and the 4D DVF was modified to deform all structures of the original 4D CT scan to this mean position. A 3D midposition (MidP) CT scan was then obtained by (arithmetic or median) averaging of the deformed 4D CT scan. Image registration accuracy, tumor shape deviation with respect to the BH CT scan, and noise were determined to evaluate the image fidelity of the MidP CT scan and the performance of the technique. Results: Accuracy of the used deformable image registration method was comparable to established automated locally rigid registration and to manual landmark registration (average difference to both methods <0.5 mm for all directions) for the tumor region. From visual assessment, the registration was good for the clearly visible features (e.g., tumor and diaphragm). The shape of the tumor, with respect to that of the BH CT scan, was better represented by the MidP reconstructions than any of the 4D CT frames (including MidV; reduction of 'shape differences' was 66%). The MidP scans contained about one-third the noise of individual 4D CT scan frames. Conclusions: We implemented an accurate method to estimate the motion of structures in a 4D CT scan. Subsequently, a novel method to create a midposition CT scan (time-weighted average of the anatomy) for treatment planning with reduced noise and artifacts was introduced. Tumor shape and position in the MidP CT scan represents that of the BH CT scan better than MidV CT scan and, therefore, was found to be appropriate for treatment planning.

  12. AC Loss Reduction in Filamentized YBCO Coated Conductors with Virtual Transverse Cross-cuts

    SciTech Connect (OSTI)

    Zhang, Yifei [ORNL; Duckworth, Robert C [ORNL; Ha, Tam T [ORNL; List III, Frederick Alyious [ORNL; Gouge, Michael J [ORNL; Chen, Y [SuperPower Incorporated, Schenectady, New York; X, Xiong, [SuperPower Incorporated, Schenectady, New York; Selvamanickam, V. [SuperPower Incorporated, Schenectady, New York

    2011-01-01T23:59:59.000Z

    While the performance of YBa{sub 2}Cu{sub 3}O{sub 7-x} (YBCO)-based coated conductors under dc currents has improved significantly in recent years, filamentization is being investigated as a technique to reduce ac loss so that the 2nd generation (2G) high temperature superconducting (HTS) wires can also be utilized in various ac power applications such as cables, transformers and fault current limiters. Experimental studies have shown that simply filamentizing the superconducting layer is not effective enough to reduce ac loss because of incomplete flux penetration in between the filaments as the length of the tape increases. To introduce flux penetration in between the filaments more uniformly and further reduce the ac loss, virtual transverse cross-cuts were made in superconducting filaments of the coated conductors fabricated using the metal organic chemical vapor deposition (MOCVD) method. The virtual transverse cross-cuts were formed by making cross-cuts (17 - 120 {micro}m wide) on the IBAD (ion beam assisted deposition)-MgO templates using laser scribing followed by depositing the superconducting layer ({approx} 0.6 {micro}m thick). AC losses were measured and compared for filamentized conductors with and without the cross-cuts under applied peak ac fields up to 100 mT. The results were analyzed to evaluate the efficacy of filament decoupling and the feasibility of using this method to achieve ac loss reduction.

  13. Absorption of ac fields in amorphous indium-oxide films

    SciTech Connect (OSTI)

    Ovadyahu, Z. [Racah Institute of Physics, the Hebrew University, Jerusalem 91904 (Israel)

    2014-08-20T23:59:59.000Z

    Absorption data from applied ac fields in Anderson-localized amorphous indium-oxide (In{sub x}O) films are shown to be frequency and disorder dependent. The absorption shows a roll-off at a frequency which is much lower than the electron-electron scattering rate of the material when it is in the diffusive regime. This is interpreted as evidence for discreteness of the energy spectrum of the deeply localized regime. This is consistent with recent many-body localization scenarios. As the metal-insulator transition is approached, the absorption shifts to higher frequencies. Comparing with the previously obtained results on the crystalline version of indium-oxide (In{sub 2}O{sub 3?x}) implies a considerably higher inelastic electron-phonon scattering rate in the amorphous material. The range over which the absorption versus frequency decreases may indicate that a wide distribution of localization length is a common feature in these systems.

  14. Fluctuation of an ion beam extracted from an AC filament driven Bernas-type ion source

    SciTech Connect (OSTI)

    Miyamoto, N., E-mail: nmiyamot@mail.doshisha.ac.jp; Okajima, Y.; Wada, M. [Graduate School of Science and Engineering, Doshisha University, Kyotanabe, Kyoto 610-0321 (Japan)] [Graduate School of Science and Engineering, Doshisha University, Kyotanabe, Kyoto 610-0321 (Japan)

    2014-02-15T23:59:59.000Z

    Argon ion beam fluctuation from an AC filament driven Bernas-type ion source is observed. The ion beam was measured by an 8 measurement elements beam profile monitor. The amplitude of the beam current fluctuation stayed in the same level from 100 Hz to 1 kHz of the filament heating frequency. The beam current fluctuation frequency measured by the beam profile monitor was equal to the frequency of the AC filament operation. The fluctuation amplitudes of the beam current by AC operation were less than 7% and were in the same level of the DC operation.

  15. Test plan for performance testing of the Eaton AC-3 electric vehicle

    SciTech Connect (OSTI)

    Crumley, R.L.; Heiselmann, H.W.

    1985-04-01T23:59:59.000Z

    An alternating current (ac) propulsion system for an electric vehicle has been developed and tested by the Eaton Corporation. The test bed vehicle is a modified 1981 Mercury Lynx. The test plan has been prepared specifically for the third modification to this test bed and identified as the Eaton AC-3. The scope of the EG and G testing at INEL to be done on the Eaton AC-3 will include coastdown and dynamometer tests but will not include environmental, on-road, or track testing. Coastdown testing will be performed in accordance with SAE J-1263 (SAE Recommended Practice for Road Load Measurement and Dynamometer Simulation Using Coastdown Techniques).

  16. Segmented superconducting tape having reduced AC losses and method of making

    DOE Patents [OSTI]

    Foltyn, Stephen R. (Los Alamos, NM); Jia, Quanxi (Los Alamos, NM); Arendt, Paul N. (Los Alamos, NM); Holesinger, Terry G. (Los Alamos, NM); Wang, Haiyan (Los Alamos, NM)

    2009-09-22T23:59:59.000Z

    A superconducting tape having reduced AC losses. The tape has a high temperature superconductor layer that is segmented. Disruptive strips, formed in one of the tape substrate, a buffer layer, and the superconducting layer create parallel discontinuities in the superconducting layer that separate the current-carrying elements of the superconducting layer into strips or filament-like structures. Segmentation of the current-carrying elements has the effect of reducing AC current losses. Methods of making such a superconducting tape and reducing AC losses in such tapes are also disclosed.

  17. EMTP modeling of CIGRE benchmark based HVDC transmission system operating with weak AC systems

    SciTech Connect (OSTI)

    Sood, V.K. [Hydro-Quebec, Varennes, Quebec (Canada); Khatri, V.; Jin, H. [Concordia Univ., Montreal, Quebec (Canada). Dept. of Electrical and Computer Engineering

    1995-12-31T23:59:59.000Z

    An EMTP based study of a CIGRE benchmark based HVDC system operating with weak ac systems is carried out. The modeled system provides a starting point for (a) educators teaching HVDC transmission courses and (b) for utility planners to develop their own low-cost dedicated digital simulators for training purposes. In this paper, modeling details of the ac-dc system, dc converters and control are presented. To validate the control schemes presented, the HVDC system is tested under ac-dc fault conditions. Results obtained from an EMTP-based study under these fault conditions are also presented in this paper.

  18. Dynamic performance of a STATCON at an HVDC inverter feeding a very weak AC system

    SciTech Connect (OSTI)

    Zhuang, Y.; Menzies, R.W. [Univ. of Manitoba, Winnipeg, Manitoba (Canada)] [Univ. of Manitoba, Winnipeg, Manitoba (Canada); Nayak, O.B. [HVDC Research Centre, Winnipeg, Manitoba (Canada)] [HVDC Research Centre, Winnipeg, Manitoba (Canada); Turanli, H.M. [Manitoba Hydro, Winnipeg, Manitoba (Canada)] [Manitoba Hydro, Winnipeg, Manitoba (Canada)

    1996-04-01T23:59:59.000Z

    This paper investigates the dynamic performance of the advanced static var compensator or STATCON at a high voltage direct current (HVDC) converter terminal where the ac system has a very low short circuit ratio (SCR). The STATCON is based on a nine-level GTO thyristor inverter. The studies include operating characteristics of the STATCON under various ac and dc disturbances. The simulation results are compared with other types of reactive power compensation options available for such applications. It is shown that the STATCON has clear advantages over the other compensators, in areas such as; fault response time, voltage support ability, and dc recovery, while operating with very weak ac systems.

  19. Estimation of the weighted CTDI{sub {infinity}} for multislice CT examinations

    SciTech Connect (OSTI)

    Li Xinhua; Zhang Da; Liu, Bob [Division of Diagnostic Imaging Physics, Department of Radiology, Massachusetts General Hospital, Boston, Massachusetts 02114 (United States)

    2012-02-15T23:59:59.000Z

    Purpose: The aim of this study was to examine the variations of CT dose index (CTDI) efficiencies, {epsilon}(CTDI{sub 100})=CTDI{sub 100}/CTDI{sub {infinity}}, with bowtie filters and CT scanner types. Methods: This was an extension of our previous study [Li, Zhang, and Liu, Phys. Med. Biol. 56, 5789-5803 (2011)]. A validated Monte Carlo program was used to calculate {epsilon}(CTDI{sub 100}) on a Siemens Somatom Definition scanner. The {epsilon}(CTDI{sub 100}) dependencies on tube voltages and beam widths were tested in previous studies. The influences of different bowtie filters and CT scanner types were examined in this work. The authors tested the variations of {epsilon}(CTDI{sub 100}) with bowtie filters on the Siemens Definition scanner. The authors also analyzed the published CTDI measurements of four independent studies on five scanners of four models from three manufacturers. Results: On the Siemens Definition scanner, the difference in {epsilon}(CTDI{sub W}) between using the head and body bowtie filters was 2.5% (maximum) in the CT scans of the 32-cm phantom, and 1.7% (maximum) in the CT scans of the 16-cm phantom. Compared with CTDI{sub W}, the weighted CTDI{sub {infinity}} increased by 30.5% (on average) in the 32-cm phantom, and by 20.0% (on average) in the 16-cm phantom. These results were approximately the same for 80-140 kV and 1-40 mm beam widths (4.2% maximum deviation). The differences in {epsilon}(CTDI{sub 100}) between the simulations and the direct measurements of four previous studies were 1.3%-5.0% at the center/periphery of the 16-cm/32-cm phantom (on average). Conclusions: Compared with CTDI{sub vol}, the equilibrium dose for large scan lengths is 30.5% higher in the 32-cm phantom, and is 20.0% higher in the 16-cm phantom. The relative increases are practically independent of tube voltages (80-140 kV), beam widths (up to 4 cm), and the CT scanners covered in this study.

  20. Correlation between human observer performance and model observer performance in differential phase contrast CT

    SciTech Connect (OSTI)

    Li, Ke; Garrett, John [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 (United States)] [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 (United States); Chen, Guang-Hong [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 and Department of Radiology, University of Wisconsin-Madison, 600 Highland Avenue, Madison, Wisconsin 53792 (United States)] [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 and Department of Radiology, University of Wisconsin-Madison, 600 Highland Avenue, Madison, Wisconsin 53792 (United States)

    2013-11-15T23:59:59.000Z

    Purpose: With the recently expanding interest and developments in x-ray differential phase contrast CT (DPC-CT), the evaluation of its task-specific detection performance and comparison with the corresponding absorption CT under a given radiation dose constraint become increasingly important. Mathematical model observers are often used to quantify the performance of imaging systems, but their correlations with actual human observers need to be confirmed for each new imaging method. This work is an investigation of the effects of stochastic DPC-CT noise on the correlation of detection performance between model and human observers with signal-known-exactly (SKE) detection tasks.Methods: The detectabilities of different objects (five disks with different diameters and two breast lesion masses) embedded in an experimental DPC-CT noise background were assessed using both model and human observers. The detectability of the disk and lesion signals was then measured using five types of model observers including the prewhitening ideal observer, the nonprewhitening (NPW) observer, the nonprewhitening observer with eye filter and internal noise (NPWEi), the prewhitening observer with eye filter and internal noise (PWEi), and the channelized Hotelling observer (CHO). The same objects were also evaluated by four human observers using the two-alternative forced choice method. The results from the model observer experiment were quantitatively compared to the human observer results to assess the correlation between the two techniques.Results: The contrast-to-detail (CD) curve generated by the human observers for the disk-detection experiments shows that the required contrast to detect a disk is inversely proportional to the square root of the disk size. Based on the CD curves, the ideal and NPW observers tend to systematically overestimate the performance of the human observers. The NPWEi and PWEi observers did not predict human performance well either, as the slopes of their CD curves tended to be steeper. The CHO generated the best quantitative agreement with human observers with its CD curve overlapping with that of human observer. Statistical equivalence between CHO and humans can be claimed within 11% of the human observer results, including both the disk and lesion detection experiments.Conclusions: The model observer method can be used to accurately represent human observer performance with the stochastic DPC-CT noise for SKE tasks with sizes ranging from 8 to 128 pixels. The incorporation of the anatomical noise remains to be studied.

  1. Cholecystokinin-Assisted Hydrodissection of the Gallbladder Fossa during FDG PET/CT-guided Liver Ablation

    SciTech Connect (OSTI)

    Tewari, Sanjit O., E-mail: tewaris@mskcc.org [Memorial Sloan-Kettering Cancer Center, Molecular Imaging and Therapy Service, Department of Radiology (United States); Petre, Elena N., E-mail: petree@mskcc.org [Memorial Sloan-Kettering Cancer Center, Interventional Radiology Service, Department of Radiology (United States); Osborne, Joseph, E-mail: osbornej@mskcc.org [Memorial Sloan-Kettering Cancer Center, Molecular Imaging and Therapy Service, Department of Radiology (United States)] [Memorial Sloan-Kettering Cancer Center, Molecular Imaging and Therapy Service, Department of Radiology (United States); Sofocleous, Constantinos T., E-mail: sofoclec@mskcc.org [Memorial Sloan-Kettering Cancer Center, Interventional Radiology Service, Department of Radiology (United States)

    2013-12-15T23:59:59.000Z

    A 68-year-old female with colorectal cancer developed a metachronous isolated fluorodeoxyglucose-avid (FDG-avid) segment 5/6 gallbladder fossa hepatic lesion and was referred for percutaneous ablation. Pre-procedure computed tomography (CT) images demonstrated a distended gallbladder abutting the segment 5/6 hepatic metastasis. In order to perform ablation with clear margins and avoid direct puncture and aspiration of the gallbladder, cholecystokinin was administered intravenously to stimulate gallbladder contraction before hydrodissection. Subsequently, the lesion was ablated successfully with sufficient margins, of greater than 1.0 cm, using microwave with ultrasound and FDG PET/CT guidance. The patient tolerated the procedure very well and was discharged home the next day.

  2. Adaptive nonlocal means filtering based on local noise level for CT denoising

    SciTech Connect (OSTI)

    Li, Zhoubo; Trzasko, Joshua D.; Lake, David S.; Blezek, Daniel J.; Manduca, Armando, E-mail: manduca.armando@mayo.edu [Department of Physiology and Biomedical Engineering, Mayo Clinic, Rochester, Minnesota 55905 (United States)] [Department of Physiology and Biomedical Engineering, Mayo Clinic, Rochester, Minnesota 55905 (United States); Yu, Lifeng; Fletcher, Joel G.; McCollough, Cynthia H. [Department of Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States)] [Department of Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States)

    2014-01-15T23:59:59.000Z

    Purpose: To develop and evaluate an image-domain noise reduction method based on a modified nonlocal means (NLM) algorithm that is adaptive to local noise level of CT images and to implement this method in a time frame consistent with clinical workflow. Methods: A computationally efficient technique for local noise estimation directly from CT images was developed. A forward projection, based on a 2D fan-beam approximation, was used to generate the projection data, with a noise model incorporating the effects of the bowtie filter and automatic exposure control. The noise propagation from projection data to images was analytically derived. The analytical noise map was validated using repeated scans of a phantom. A 3D NLM denoising algorithm was modified to adapt its denoising strength locally based on this noise map. The performance of this adaptive NLM filter was evaluated in phantom studies in terms of in-plane and cross-plane high-contrast spatial resolution, noise power spectrum (NPS), subjective low-contrast spatial resolution using the American College of Radiology (ACR) accreditation phantom, and objective low-contrast spatial resolution using a channelized Hotelling model observer (CHO). Graphical processing units (GPU) implementation of this noise map calculation and the adaptive NLM filtering were developed to meet demands of clinical workflow. Adaptive NLM was piloted on lower dose scans in clinical practice. Results: The local noise level estimation matches the noise distribution determined from multiple repetitive scans of a phantom, demonstrated by small variations in the ratio map between the analytical noise map and the one calculated from repeated scans. The phantom studies demonstrated that the adaptive NLM filter can reduce noise substantially without degrading the high-contrast spatial resolution, as illustrated by modulation transfer function and slice sensitivity profile results. The NPS results show that adaptive NLM denoising preserves the shape and peak frequency of the noise power spectrum better than commercial smoothing kernels, and indicate that the spatial resolution at low contrast levels is not significantly degraded. Both the subjective evaluation using the ACR phantom and the objective evaluation on a low-contrast detection task using a CHO model observer demonstrate an improvement on low-contrast performance. The GPU implementation can process and transfer 300 slice images within 5 min. On patient data, the adaptive NLM algorithm provides more effective denoising of CT data throughout a volume than standard NLM, and may allow significant lowering of radiation dose. After a two week pilot study of lower dose CT urography and CT enterography exams, both GI and GU radiology groups elected to proceed with permanent implementation of adaptive NLM in their GI and GU CT practices. Conclusions: This work describes and validates a computationally efficient technique for noise map estimation directly from CT images, and an adaptive NLM filtering based on this noise map, on phantom and patient data. Both the noise map calculation and the adaptive NLM filtering can be performed in times that allow integration with clinical workflow. The adaptive NLM algorithm provides effective denoising of CT data throughout a volume, and may allow significant lowering of radiation dose.

  3. Mission Support Contract Attachment J.10 Contract No. DE-AC06...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    J.10 Contract No. DE-AC06-09RL14728 Modification 369 Table Of Contents J.10-1 SERVICE CONTRACT ACT: WAGE DETERMINATION ... 2 J.10-2 DAVIS...

  4. Rotating electrical machines - Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets

    E-Print Network [OSTI]

    International Electrotechnical Commission. Geneva

    1996-01-01T23:59:59.000Z

    Establishes the principal characteristics of a.c. generators under the control of their voltage regulators when used for reciprocating internal combustion engine driven generating sets. Supplements the requirements given in IEC 60034-1.

  5. AEP (Central and SWEPCO)- Coolsaver A/C Tune Up or Replacement

    Broader source: Energy.gov [DOE]

    Participating customers are eligible to receive a $75 coupon for use toward A/C and heat pump efficiency services performed as a result of the program’s tune-up analysis, contractors are eligible...

  6. Solar Electric Grid Integration- Advanced Concepts (SEGIS-AC) Funding Opportunity

    Broader source: Energy.gov [DOE]

    Through the Solar Electric Grid Integration – Advanced Concepts (SEGIS-AC) program, DOE is funding solar projects that are targeting ways to develop power electronics and build smarter, more...

  7. AC losses in type-II superconductors induced by nonuniform fluctuations of external magnetic field

    E-Print Network [OSTI]

    as the economic gains of implementation of type-II superconductors in power transmission lines, current leads amplitude. The results can be used to estimate the AC losses in flywheels, electric motors, magnetic shields

  8. Development and application of setup for ac magnetic field in neutron scattering experiments

    SciTech Connect (OSTI)

    Klimko, Sergey [Laboratoire Leon Brillouin, 91191 Gif-sur-Yvette (France); Zhernenkov, Kirill; Toperverg, Boris P.; Zabel, Hartmut [Institut fuer Festkoerperphys IV, Ruhr Universitaet Bochum, D-44780 Bochum (Germany)

    2010-10-15T23:59:59.000Z

    We report on a new setup developed for neutron scattering experiments in periodically alternating magnetic fields at the sample position. The assembly consisting of rf generator, amplifier, wide band transformer, and resonance circuit. It allows to generate homogeneous ac magnetic fields over a volume of a few cm{sup 3} and variable within a wide range of amplitudes and frequencies. The applicability of the device is exemplified by ac polarized neutron reflectometry (PNR): a new method established to probe remagnetization kinetics in soft ferromagnetic films. Test experiments with iron films demonstrate that the ac field within the accessible range of frequencies and amplitudes produces a dramatic effect on the PNR signal. This shows that the relevant ac field parameters generated by the device match well with the scales involved in the remagnetization processes. Other possible applications of the rf unit are briefly discussed.

  9. acs_NL_nl-2011-03332e 1..8

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    | Nano Lett. 2011, 11, 5071-5078 LETTER pubs.acs.orgNanoLett Hierarchically Porous Graphene as a LithiumAir Battery Electrode Jie Xiao,* , Donghai Mei, Xiaolin Li, ...

  10. Docket No. EERE-2012-BT-TP-0046; RIN 1904-AC52 Ex partecommunication...

    Broader source: Energy.gov (indexed) [DOE]

    & Publications Docket No. EERE-2012-BT-TP-0046; RIN 1904-AC52 Docket No. EERE-2012-BT-TP-0046 Ex Parte Communication Ex Parte Memorandum on Set Top Boxes and Network Equipment...

  11. System and Battery Charge Control for PV-Powered AC Lighting Systems

    SciTech Connect (OSTI)

    Kern, G.

    1999-04-01T23:59:59.000Z

    This report reviews a number of issues specific to stand-alone AC lighting systems. A review of AC lighting technology is presented, which discusses the advantages and disadvantages of various lamps. The best lamps for small lighting systems are compact fluorescent. The best lamps for intermediate-size systems are high- or low-pressure sodium. Specifications for battery charging and load control are provided with the goal of achieving lamp lifetimes on the order of 16,000 to 24,000 hours and battery lifetimes of 4 to 5 years. A rough estimate of the potential domestic and global markets for stand-alone AC lighting systems is presented. DC current injection tests were performed on high-pressure sodium lamps and the test results are presented. Finally, a prototype system was designed and a prototype system controller (with battery charger and DC/AC inverter) was developed and built.

  12. Alameda-Contra Costa Transit District (AC Transit) Fuel Cell Transit Buses: Preliminary Evaluation Results

    SciTech Connect (OSTI)

    Chandler, K.; Eudy, L.

    2007-03-01T23:59:59.000Z

    This report provides an evaluation of three prototype fuel cell-powered transit buses operating at AC Transit in Oakland, California, and six baseline diesel buses similar in design to the fuel cell buses.

  13. AEP (Central and SWEPCO) - Coolsaver A/C Tune Up | Department...

    Office of Environmental Management (EM)

    Participating customers are eligible to receive a 75 coupon for use toward AC and heat pump efficiency services performed as a result of the program's tune-up analysis....

  14. Measured Savings of DC to AC Drive Retrofit in Plastic Extrusion

    E-Print Network [OSTI]

    Sfeir, R. A.

    2008-01-01T23:59:59.000Z

    This paper presents the potential electrical energy efficiency improvements for utilizing alternating current (AC) motors controlled by variable frequency drives (VFD) in place of direct current (DC) motors to drive plastic extrusion machines. A...

  15. ac gly3 h2o3: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 354 www.eprg.group.cam.ac.uk...

  16. ac 66-1100 kv: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 403 www.eprg.group.cam.ac.uk...

  17. ac metal-enclosed switchgear: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    limits. The models are used to estimate the benefits of electricity locational marginal pricing (LMP) that arise from de Gispert, Adri 348 www.eprg.group.cam.ac.uk...

  18. Lift-and-Project Relaxations of AC Microgrid Distribution System Planning

    E-Print Network [OSTI]

    Taylor, Joshua A.

    2011-01-01T23:59:59.000Z

    We apply relaxation procedures to polynomial optimization problems that originate in transmission system planning, and obtain new convex formulations for the AC case. The approach is novel because the optimization is ...

  19. MIT Electric Vehicle Team Porsche designing a cooling system for the AC24 electric motor

    E-Print Network [OSTI]

    Meenen, Jordan N

    2010-01-01T23:59:59.000Z

    In this thesis I worked on the design and analysis of a cooling system for the electric motor of the MIT Electric Vehicle Team's Porsche 914 Battery Electric Vehicle. The vehicle's Azure Dynamics AC24 motor tended to ...

  20. Ultrafast High-pressure AC Electro-osmotic Pumps for Portable Biomedical Microfluidics

    E-Print Network [OSTI]

    Huang, Chien-Chih

    This paper details the development of an integrated AC electro-osmotic (ACEO) microfluidic pump for dilute electrolytes consisting of a long serpentine microchannel lined with three dimensional (3D) stepped electrode arrays. ...

  1. acs_JZ_jz-2011-01312e 1..6

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    jz201312e | J. Phys. Chem. Lett. 2011, 2, 2859-2864 LETTER pubs.acs.orgJPCL Supercapacitor Capacitance Exhibits Oscillatory Behavior as a Function of Nanopore Size Guang...

  2. On-Orbit Performance of the ACS Solar Blind Channel Hien D. Trana

    E-Print Network [OSTI]

    Johns Hopkins University, Department of Physics and Astonomy, Advanced Camera for Surveys Team

    MAMA detector, the ACS/SBC has bright-object limits to protect it from radiation damage. For non the whole detector) limit is optical performance of the SBC is comparable

  3. www.arts.canterbury.ac.nz/internships Project Title: Campaign Assistant: FLUXX: Ideas in

    E-Print Network [OSTI]

    Hickman, Mark

    and supplier research using the internet and phone, client communication, picking up event equipment(s) for the academic adviser #12;www.arts.canterbury.ac.nz/internships Necessary Qualifications: Major/Minors(s): Coms

  4. Evaluation of the potential utility of flat panel CT for quantifying relative contrast enhancement

    SciTech Connect (OSTI)

    Jones, A. Kyle; Mahvash, Armeen [Department of Imaging Physics, Division of Diagnostic Imaging, University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States); Department of Interventional Radiology, Division of Diagnostic Imaging, University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States)

    2012-07-15T23:59:59.000Z

    Purpose: Certain directed oncologic therapies seek to take advantage of the fact that tumors are typically more susceptible to directed therapeutic agents than normal tissue owing to their extensive networks of poorly formed, leaky vasculature. If differences between the vascularity of normal and tumor tissues could be quantified, patients could be selected for or excluded from directed treatments on the basis of this difference. However, angiographic imaging techniques such as digital subtraction angiography (DSA) yield two-dimensional data that may be inadequate for this task. As a first step, the authors evaluated the feasibility of using a commercial implementation of flat panel computed tomography (FPCT) to quantify differences in enhancement of a simulated tumor compared with normal tissue based on differences in CT number measured in precontrast and postcontrast scans. Methods: To evaluate the FPCT scanner studied, the authors scanned several phantoms containing simulated normal and tumor tissues. In the first experiment, the authors used an anthropomorphic phantom containing inclusions representing normal, tumor, and bone tissue to evaluate the constancy of CT numbers in scans repeated at clinically relevant intervals of 1 and 3 min. The authors then scanned gelatin phantoms containing dilutions of iodinated contrast to evaluate the accuracy of relative contrast enhancement measurements for a clinical FPCT system. Data were analyzed using widely available software. Results: CT numbers measured in identical locations were constant over both scan intervals evaluated. Measured relative contrast enhancement values were accurate compared with known relative contrast enhancement values. Care must be taken to avoid artifacts in reconstructed images when placing regions of interest. Conclusions: Despite its limitations, FPCT in the interventional laboratory can be used to quantify relative contrast enhancement in phantoms. This is accomplished by measuring CT number in simulated tumor and normal tissue on precontrast and postcontrast scans. This information opens the door for refinement of technique in an effort to use such a technique to plan directed therapies.

  5. Transhepatic CT-Guided Radiofrequency Ablation of Adrenal Metastases from Hepatocellular Carcinoma

    SciTech Connect (OSTI)

    Kuehl, Hilmar, E-mail: hilmar.kuehl@uni-due.de; Stattaus, Joerg; Forsting, Michael; Antoch, Gerald [University Hospital Essen, University at Duisburg-Essen, Department of Diagnostic and Interventional Radiology and Neuroradiology (Germany)

    2008-11-15T23:59:59.000Z

    The prognosis of patients with adrenal metastases from hepatocellular carcinoma (HCC) has been poor, and aggressive treatment of these tumors is mandatory to improve patients' survival. Since adrenalectomy may be difficult to perform after previous surgery of the right liver lobe, other approaches are required to treat the adrenal mass. This report aims at demonstrating the feasibility of CT-guided transhepatic radiofrequency ablation of right adrenal HCC metastases pretreated with chemoembolization in patients unable to undergo surgical resection.

  6. SU-E-T-93: Creation of Standardized APBI SAVI Cavities Using CT Registration

    SciTech Connect (OSTI)

    Dahl, R [Mayo Clinic, Rochester, MN (United States)

    2014-06-01T23:59:59.000Z

    Purpose: Develop a consistent and rapid method of generating the initial cavity structure for Accelerated Partial Breast Irradiation (APBI) using the SAVI applicator. Methods: Four SAVI (Cianna Medical) applicators (6-1 Mini, 6-1, 8-1, and 10-1) were scanned on a CT simulator. The applicators were scanned in air with the CT slices (0.625mm axial thickness) perpendicular to the long axis of the applicator. Following scanning the CT images were transferred to Eclipse (Varian Medical Systems) and contours of the cavity were drawn. The cavity proximal and distal locations were defined according to MD specification. The scans and contours were then re-imported into the CT virtual simulation workstation.At the time of patient planning the appropriate applicator scan is anonymized and imported into Eclipse. In Brachytherapy Planning two Marker points are placed, one at the distal band location (cavity start) and the second at a defined distance along the applicator (cavity end). The actual patient scan is then registered to the applicator scan. A three point match is used to quickly get the two scans in approximate alignment. Manually matching is then used to fine tune the alignment of the cavity contour and Marker points. Results: The standard applicator scans have shown to agree well with the applicators in the patient scans. The time taken to register the scans has shown to be less than generating the cavities using the standard methods of contouring on the axial slices or using the dose shaper with sources in the central channel. Conclusion: The registration of a standard applicator scan and contour has improved the consistency in the generation of the initial cavity (SAVI) structure. Planning structures used for dose calculation are created with that structure as a starting point so accuracy and consistency are important for dose evaluation and plan comparison.

  7. SU-E-I-43: Pediatric CT Dose and Image Quality Optimization

    SciTech Connect (OSTI)

    Stevens, G; Singh, R [GE Healthcare, Waukesha, WI (United States)

    2014-06-01T23:59:59.000Z

    Purpose: To design an approach to optimize radiation dose and image quality for pediatric CT imaging, and to evaluate expected performance. Methods: A methodology was designed to quantify relative image quality as a function of CT image acquisition parameters. Image contrast and image noise were used to indicate expected conspicuity of objects, and a wide-cone system was used to minimize scan time for motion avoidance. A decision framework was designed to select acquisition parameters as a weighted combination of image quality and dose. Phantom tests were used to acquire images at multiple techniques to demonstrate expected contrast, noise and dose. Anthropomorphic phantoms with contrast inserts were imaged on a 160mm CT system with tube voltage capabilities as low as 70kVp. Previously acquired clinical images were used in conjunction with simulation tools to emulate images at different tube voltages and currents to assess human observer preferences. Results: Examination of image contrast, noise, dose and tube/generator capabilities indicates a clinical task and object-size dependent optimization. Phantom experiments confirm that system modeling can be used to achieve the desired image quality and noise performance. Observer studies indicate that clinical utilization of this optimization requires a modified approach to achieve the desired performance. Conclusion: This work indicates the potential to optimize radiation dose and image quality for pediatric CT imaging. In addition, the methodology can be used in an automated parameter selection feature that can suggest techniques given a limited number of user inputs. G Stevens and R Singh are employees of GE Healthcare.

  8. Retrocrural splanchnic nerve alchohol neurolysis with a CT-guided anterior transaortic approach

    SciTech Connect (OSTI)

    Fields, S. [Hadassah University Hospital, Jerusalem (Israel)] [Hadassah University Hospital, Jerusalem (Israel)

    1996-01-01T23:59:59.000Z

    Retrocrural splanchnic nerve alcohol neurolysis with a CT-guided anterior transonic approach, a new method for splanchnic block alleviation of chronic abdominal pain, is described. Ten patients with chronic abdominal pain requiring narcotic treatment, six with pancreatic carcinoma, one with gastric carcinoma, two with chronic pancreatitis, and one with pain of unknown etiology, were referred for splanchnic nerve neurolysis. With CT guidance, a 20 gauge needle was placed through the aorta into the retrocrural space at T11-T12, and 5-15 ml 96% alcohol was injected into the retrocrural space. Following the procedure, 6 of 10 patients were pain free, 2 patients had temporary pain relief, and 2 patients were without response. There were no significant complications. CT-guided anterior transaortic retrocrural splanchnic nerve alcohol neurolysis is technically feasible, easier to perform than the classic posterolateral approach, and may have less risk of complications. The success rate in this initial trial was reasonable and, therefore, this technique provides an additional method for the treatment of abdominal pain. 12 refs., 2 figs.

  9. CT-Guided Radiofrequency Ablation in Patients with Hepatic Metastases from Breast Cancer

    SciTech Connect (OSTI)

    Jakobs, Tobias F., E-mail: tobias.jakobs@med.uni-muenchen.de; Hoffmann, Ralf-Thorsten; Schrader, Angelika [Ludwig-Maximilians-University of Munich, Department of Radiology (Germany); Stemmler, Hans Joachim [Ludwig-Maximilians-University of Munich, Department of Internal Medicine III (Germany); Trumm, Christoph [Ludwig-Maximilians-University of Munich, Department of Radiology (Germany); Lubienski, Andreas [University of Schleswig-Holstein, Department of Radiology (Germany); Murthy, Ravi [The University of Texas M. D. Anderson Cancer Center, Division of Diagnostic Imaging (United States); Helmberger, Thomas K. [Klinikum Bogenhausen, Department of Radiology (Germany); Reiser, Maximilian F. [Ludwig-Maximilians-University of Munich, Department of Radiology (Germany)

    2009-01-15T23:59:59.000Z

    The purpose of this study was to evaluate technical success, technique effectiveness, and survival following radiofrequency ablation for breast cancer liver metastases and to determine prognostic factors. Forty-three patients with 111 breast cancer liver metastases underwent CT-guided percutaneous radiofrequency (RF) ablation. Technical success and technique effectiveness was evaluated by performing serial CT scans. We assessed the prognostic value of hormone receptor status, overexpression of human epidermal growth factor receptor 2 (HER2), and presence of extrahepatic tumor spread. Survival rates were calculated using the Kaplan-Meier method. Technical success was achieved in 107 metastases (96%). Primary technique effectiveness was 96%. During follow-up local tumor progression was observed in 15 metastases, representing a secondary technique effectiveness of 86.5%. The overall time to progression to the liver was 10.5 months. The estimated overall median survival was 58.6 months. There was no significant difference in terms of survival probability with respect to hormone receptor status, HER2 overexpression, and presence of isolated bone metastases. Survival was significantly lower among patients with extrahepatic disease, with the exception of skeletal metastases. We conclude that CT-guided RF ablation of liver metastases from breast cancer can be performed with a high degree of technical success and technique effectiveness, providing promising survival rates in patients with no visceral extrahepatic disease. Solitary bone metastases did not negatively affect survival probability after RF ablation.

  10. High-Power Converters and AC Drives IEEE PESC2005 Tutorial

    E-Print Network [OSTI]

    Wu, Bin

    @ee.ryerson.ca http://www.ee.ryerson.ca/~bwu/ 2 High-Power Converters and AC Drives 1. Introduction 2. Cascaded H-Bridge Drives · High-Power Semiconductor Devices High-Power Converters and AC Drives Bin Wu 4High · Multilevel Voltage Source Inverters N dC Cascaded H-bridge (CHB) Inverter dC Two Level Inverter dC Flying

  11. www.ccfe.ac.uk CPS13.486 (August 2013)

    E-Print Network [OSTI]

    www.ccfe.ac.uk CPS13.486 (August 2013) InFusion Issue 04 | Summer 2013 The work at CCFE is funded by the RCUK Energy Programme and EURATOM Issue 04 |Summer 2013 www.ccfe.ac.uk InFusion CCFE Show and Tell visit to site power supplies Changing times for MAST #12;InFusion Issue 04 | Summer 2013 In this issue

  12. www.ccfe.ac.uk CPS13.1239 (March 2014)

    E-Print Network [OSTI]

    www.ccfe.ac.uk CPS13.1239 (March 2014) InFusion Issue 05 | Spring 2014 The work at CCFE is funded by the RCUK Energy Programme and EURATOM Issue 05 |Spring 2014 www.ccfe.ac.uk InFusion Themakingoffusion's see if it behaves hoW we expect... #12;InFusion Issue 05 | Spring 2014 In this issue 04 The story

  13. Quality assurance for image-guided radiation therapy utilizing CT-based technologies: A report of the AAPM TG-179

    SciTech Connect (OSTI)

    Bissonnette, Jean-Pierre; Balter, Peter A.; Dong Lei; Langen, Katja M.; Lovelock, D. Michael; Miften, Moyed; Moseley, Douglas J.; Pouliot, Jean; Sonke, Jan-Jakob; Yoo, Sua [Task Group 179, Department of Radiation Physics, Princess Margaret Hospital, University of Toronto, Toronto, Ontario, M5G 2M9 (Canada); Department of Radiation Physics, University of Texas M.D. Anderson Cancer Center, Houston, Texas 77030 (United States); Department of Radiation Oncology, M. D. Anderson Cancer Center Orlando, Orlando, Florida 32806 (United States); Department of Medical Physics, Memorial Sloan-Kettering Cancer Center, New York, New York 10021 (United States); Department of Radiation Oncology, University of Colorado School of Medicine, Aurora, Colorado 80045 (United States); Department of Radiation Physics, Princess Margaret Hospital, University of Toronto, Toronto, Ontario, M5G 2M9 (Canada); Department of Radiation Oncology, UCSF Comprehensive Cancer Center, 1600 Divisadero St., Suite H 1031, San Francisco, California 94143-1708 (United States); Department of Radiation Oncology, Netherlands Cancer Institute-Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Department of Radiation Oncology, Duke University, Durham, North Carolina 27710 (United States)

    2012-04-15T23:59:59.000Z

    Purpose: Commercial CT-based image-guided radiotherapy (IGRT) systems allow widespread management of geometric variations in patient setup and internal organ motion. This document provides consensus recommendations for quality assurance protocols that ensure patient safety and patient treatment fidelity for such systems. Methods: The AAPM TG-179 reviews clinical implementation and quality assurance aspects for commercially available CT-based IGRT, each with their unique capabilities and underlying physics. The systems described are kilovolt and megavolt cone-beam CT, fan-beam MVCT, and CT-on-rails. A summary of the literature describing current clinical usage is also provided. Results: This report proposes a generic quality assurance program for CT-based IGRT systems in an effort to provide a vendor-independent program for clinical users. Published data from long-term, repeated quality control tests form the basis of the proposed test frequencies and tolerances.Conclusion: A program for quality control of CT-based image-guidance systems has been produced, with focus on geometry, image quality, image dose, system operation, and safety. Agreement and clarification with respect to reports from the AAPM TG-101, TG-104, TG-142, and TG-148 has been addressed.

  14. Freehand Two-Step CT-Guided Brain Tumor Biopsy: A Fast and Effective Interventional Procedure in Selected Patients

    SciTech Connect (OSTI)

    Thanos, Loukas, E-mail: loutharad@yahoo.com; Mylona, Sofia; Galani, Panagiota; Kalioras, Vasilios; Pomoni, Maria; Batakis, Nikolaos ['Korgialeneio-Benakeio', Hellenic Red-Cross Hospital of Athens, Radiology Department (Greece)

    2006-04-15T23:59:59.000Z

    Purpose. To evaluate the efficacy and safety of CT-guided needle biopsy of brain lesions without a stereotactic device, and to determine the best possible indications for this technique. Methods. From February 2001 to February 2004, 20 patients (12 men, 8 women; age 61-82 years) underwent CT-guided brain lesion biopsy. The procedure started with a brain CT scan for lesion localization and for selection of the inlet for needle insertion. The patient was then transported to the operating room where cranioanatrisis was performed. Subsequently, the biopsy was performed under CT guidance using a 14G brain biopsy needle with a blind smooth end and lateral holes. At the end of the biopsy, the field was checked for possible complications with a CT scan. Results. Histopathologic results were: brain tumor in 16 patients (80%), inflammatory process in 3 (15%), and no conclusive diagnosis in 1 (5%). A repeat of the process was required in 2 patients. A minor complication of local hematoma was found in 1 patient (5%). There were no deaths or other serious complications.Conclusion. CT-guided biopsy is a reliable method for histopathologic diagnosis of brain lesions in selected cases. It is a simple, fast, effective, low-cost procedure with minimal complications, indicated especially for superficial and large tumors.

  15. Ratchet Effect and Nonlinear Transport for Particles on Random Substrates with Crossed ac Drives

    E-Print Network [OSTI]

    C. Reichhardt; C. J. Olson Reichhardt

    2005-09-13T23:59:59.000Z

    We show in simulations that overdamped interacting particles in two dimensions with a randomly disordered substrate can exhibit novel nonequilibrium transport phenomena including a transverse ratchet effect, where a combined dc drive and circular ac drive produce a drift velocity in the direction transverse to the applied dc drive. The random disorder does not break any global symmetry; however, in two dimensions, symmetry breaking occurs due to the chirality of the circular drive. In addition to inducing the transverse ratchet effect, increasing the ac amplitude also strongly affects the longitudinal velocity response and can produce what we term an overshoot effect where the longitudinal dc velocity is higher in the presence of the ac drive than it would be for a dc drive alone. We also find a dynamical reordering transition upon increasing the ac amplitude. In the absence of a dc drive, it is possible to obtain a ratchet effect when the combined ac drives produce particle orbits that break a reflection symmetry. In this case, as the ac amplitude increases, current reversals can occur. These effects may be observable for vortices in type II superconductors as well as for colloids interacting with random substrates.

  16. Comparison of the Unique Mobility and DOE-developed ac electric drive systems

    SciTech Connect (OSTI)

    Cole, G.H.

    1993-01-01T23:59:59.000Z

    A comparison was made between the most recent DOE-developed AC electric vehicle drive systems and that which is independently under development by Unique Mobility of Golden, Colorado. The DOE-developed AC systems compared in this study are the Single-Shaft Electric Propulsion System (ETX-II) developed by Ford Motor Company and the General Electric Company under contract number DE-AC07-85NV10418, the Dual-Shaft Electric Propulsion (DSEP) System developed by Eaton Corporation under contract number DOE-AC08-84NV-10366, and the anticipated results of the Modular Electric Vehicle (MEV) system currently being developed by Ford and General Electric under contract number DE-AC07-90ID13019. The Unique Mobility brushless DC electric vehicle drive system represents their latest electric drive technology and is being developed in cooperation with BMW Technik Gmbh of Germany. Comparisons of specific volume, specific weight, efficiency and expected vehicle performance are made of the different systems based upon measured system performance data where available. One conclusion presented is that the Unique Mobility drive system under development with BMW appears to provide comparable performance to the AC systems studied.

  17. The effects of gantry tilt on breast dose and image noise in cardiac CT

    SciTech Connect (OSTI)

    Hoppe, Michael E.; Gandhi, Diksha; Schmidt, Taly Gilat [Department of Biomedical Engineering, Marquette University, Milwaukee, Wisconsin 53233 (United States)] [Department of Biomedical Engineering, Marquette University, Milwaukee, Wisconsin 53233 (United States); Stevens, Grant M. [GE Healthcare, Waukesha, Wisconsin 53188 (United States)] [GE Healthcare, Waukesha, Wisconsin 53188 (United States); Foley, W. Dennis [Department of Radiology, Medical College of Wisconsin, Froedtert Memorial Lutheran Hospital, Milwaukee, Wisconsin 53226 (United States)] [Department of Radiology, Medical College of Wisconsin, Froedtert Memorial Lutheran Hospital, Milwaukee, Wisconsin 53226 (United States)

    2013-12-15T23:59:59.000Z

    Purpose: This study investigated the effects of tilted-gantry acquisition on image noise and glandular breast dose in females during cardiac computed tomography (CT) scans. Reducing the dose to glandular breast tissue is important due to its high radiosensitivity and limited diagnostic significance in cardiac CT scans.Methods: Tilted-gantry acquisition was investigated through computer simulations and experimental measurements. Upon IRB approval, eight voxelized phantoms were constructed from previously acquired cardiac CT datasets. Monte Carlo simulations quantified the dose deposited in glandular breast tissue over a range of tilt angles. The effects of tilted-gantry acquisition on breast dose were measured on a clinical CT scanner (CT750HD, GE Healthcare) using an anthropomorphic phantom with MOSFET dosimeters in the breast regions. In both simulations and experiments, scans were performed at gantry tilt angles of 0°–30°, in 5° increments. The percent change in breast dose was calculated relative to the nontilted scan for all tilt angles. The percent change in noise standard deviation due to gantry tilt was calculated in all reconstructed simulated and experimental images.Results: Tilting the gantry reduced the breast dose in all simulated and experimental phantoms, with generally greater dose reduction at increased gantry tilts. For example, at 30° gantry tilt, the dosimeters located in the superior, middle, and inferior breast regions measured dose reductions of 74%, 61%, and 9%, respectively. The simulations estimated 0%–30% total breast dose reduction across the eight phantoms and range of tilt angles. However, tilted-gantry acquisition also increased the noise standard deviation in the simulated phantoms by 2%–50% due to increased pathlength through the iodine-filled heart. The experimental phantom, which did not contain iodine in the blood, demonstrated decreased breast dose and decreased noise at all gantry tilt angles.Conclusions: Tilting the gantry reduced the dose to the breast, while also increasing noise standard deviation. Overall, the noise increase outweighed the dose reduction for the eight voxelized phantoms, suggesting that tilted gantry acquisition may not be beneficial for reducing breast dose while maintaining image quality.

  18. Correlation between model observer and human observer performance in CT imaging when lesion location is uncertain

    SciTech Connect (OSTI)

    Leng, Shuai; Yu, Lifeng; Zhang, Yi; McCollough, Cynthia H. [Department of Radiology, Mayo Clinic, 200 First Street Southwest, Rochester, Minnesota 55905 (United States)] [Department of Radiology, Mayo Clinic, 200 First Street Southwest, Rochester, Minnesota 55905 (United States); Carter, Rickey [Department of Biostatistics, Mayo Clinic, 200 First Street Southwest, Rochester, Minnesota 55905 (United States)] [Department of Biostatistics, Mayo Clinic, 200 First Street Southwest, Rochester, Minnesota 55905 (United States); Toledano, Alicia Y. [Biostatistics Consulting, LLC, 10606 Wheatley Street, Kensington, Maryland 20895 (United States)] [Biostatistics Consulting, LLC, 10606 Wheatley Street, Kensington, Maryland 20895 (United States)

    2013-08-15T23:59:59.000Z

    Purpose: The purpose of this study was to investigate the correlation between model observer and human observer performance in CT imaging for the task of lesion detection and localization when the lesion location is uncertain.Methods: Two cylindrical rods (3-mm and 5-mm diameters) were placed in a 35 × 26 cm torso-shaped water phantom to simulate lesions with ?15 HU contrast at 120 kV. The phantom was scanned 100 times on a 128-slice CT scanner at each of four dose levels (CTDIvol = 5.7, 11.4, 17.1, and 22.8 mGy). Regions of interest (ROIs) around each lesion were extracted to generate images with signal-present, with each ROI containing 128 × 128 pixels. Corresponding ROIs of signal-absent images were generated from images without lesion mimicking rods. The location of the lesion (rod) in each ROI was randomly distributed by moving the ROIs around each lesion. Human observer studies were performed by having three trained observers identify the presence or absence of lesions, indicating the lesion location in each image and scoring confidence for the detection task on a 6-point scale. The same image data were analyzed using a channelized Hotelling model observer (CHO) with Gabor channels. Internal noise was added to the decision variables for the model observer study. Area under the curve (AUC) of ROC and localization ROC (LROC) curves were calculated using a nonparametric approach. The Spearman's rank order correlation between the average performance of the human observers and the model observer performance was calculated for the AUC of both ROC and LROC curves for both the 3- and 5-mm diameter lesions.Results: In both ROC and LROC analyses, AUC values for the model observer agreed well with the average values across the three human observers. The Spearman's rank order correlation values for both ROC and LROC analyses for both the 3- and 5-mm diameter lesions were all 1.0, indicating perfect rank ordering agreement of the figures of merit (AUC) between the average performance of the human observers and the model observer performance.Conclusions: In CT imaging of different sizes of low-contrast lesions (?15 HU), the performance of CHO with Gabor channels was highly correlated with human observer performance for the detection and localization tasks with uncertain lesion location in CT imaging at four clinically relevant dose levels. This suggests the ability of Gabor CHO model observers to meaningfully assess CT image quality for the purpose of optimizing scan protocols and radiation dose levels in detection and localization tasks for low-contrast lesions.

  19. Low Cost Fabrication of 2G Wires for AC Applications

    SciTech Connect (OSTI)

    Kodenkandath, T.; List, F.A., III

    2005-09-15T23:59:59.000Z

    Ink-jet printing has been demonstrated as an adaptable technology for printing YBCO filaments using a Metal Organic (MO) YBCO precursor. The technology was demonstrated using AMSC's proprietary metal organic TFA-based YBCO precursor and a commercial piezoelectric print-head on RABiTS templates. Filaments with a width of 100 um and spacing of 200 um were successfully printed, decomposed and processed to YBCO. Critical currents of {approx} 200 A/cm-w were achieved in a series of filaments with a 2 mm width. The single nozzle laboratory printer used in the Phase 1 program is capable of printing {approx} 100 um wide single filaments at a rate of 8-10 cm/sec. The electrical stabilization of filaments with a Ag ink was also evaluated using ink-jet printing. The overall objective of the Phase 1 Project was the evaluation and demonstration of inkjet-printing for depositing YBCO filaments on textured templates (RABiTS, IBAD, ISD, etc. substrates) with properties appropriate for low loss ac conductors. Goals of the Phase 1 program included development of an appropriate precursor ink, demonstration of the printing process, processing and characterization of printed YBCO filaments and evaluation of the process for further development.

  20. Magnetostrictive materials and method for improving AC characteristics in same

    DOE Patents [OSTI]

    Pulvirenti, Patricia P. (Chicago, IL); Jiles, David C. (Ames, IA)

    2001-08-14T23:59:59.000Z

    The present invention provides Terfenol-D alloys ("doped" Terfenol) having optimized performances under the condition of time-dependent magnetic fields. In one embodiment, performance is optimized by lowering the conductivity of Terfenol, thereby improving the frequency response. This can be achieved through addition of Group III or IV elements, such as Si and Al. Addition of these types of elements provides scattering sites for conduction electrons, thereby increasing resistivity by 125% which leads to an average increase in penetration depth of 80% at 1 kHz and an increase in energy conversion efficiency of 55%. The permeability of doped Terfenol remains constant over a wider frequency range as compared with undoped Terfenol. These results demonstrate that adding impurities, such as Si and Al, are effective in improving the ac characteristics of Terfenol. A magnetoelastic Gruneisen parameter, .gamma..sub.me, has also been derived from the thermodynamic equations of state, and provides another means by which to characterize the coupling efficiency in magnetostrictive materials on a more fundamental basis.

  1. Improving ac motor efficiency with fuzzy logic energy optimizer

    SciTech Connect (OSTI)

    Spiegel, R.J.; Chappell, P.J.; Cleland, J.G.

    1994-08-01T23:59:59.000Z

    The paper discusses EPA's research program to develop fuzzy-logic-based energy optimizers for alternating-current (AC) induction motors driven by Adjustable Speed Drives (ASDs). The technical goals of the program are to increase the efficiency of ASD/motor combinations (especially when operating at off-rated torque/speed conditions), develop a generic controller for energy optimization that can be applied to a wide range of motors and ASDs regardless of size and application, and develop a controller for energy optimization that can eliminate the requirement for tachometer or encoder feedback, and still maintain the stability and response of closed-loop control. Electric motors use over 60% of the electrical power generated in the U.S. The U.S. population of approximately 1 billion motors use over 1700 billion kWh per year. Over 140 million new motors are sold each year. A review of the U.S. motor population reveals that 90% of the motors are less than 1 hp (fractional motors) in size, but use less than 10% of the electricity consumed by motors. More that 80% of the electricity used by motors is consumed by less than 1% of the motor population (motors greater than 20 hp). Thus, it is clear that large energy savings from improvement in motor efficiency could be achieved from a relatively small motor population.

  2. Delegation Issuing Service for X.509 D.W.Chadwick, University of Kent, Canterbury, CT2 7NZ, England

    E-Print Network [OSTI]

    Kent, University of

    .509 [1] defines a Privilege Management Infrastructure (PMI) based on attribute certificates (ACs) instead of public keys. In the X.509 PMI model, the root of the PMI is termed the Source of Authority (So

  3. System and method for monitoring and controlling stator winding temperature in a de-energized AC motor

    DOE Patents [OSTI]

    Lu, Bin (Kenosha, WI); Luebke, Charles John (Sussex, WI); Habetler, Thomas G. (Snellville, GA); Zhang, Pinjia (Atlanta, GA); Becker, Scott K. (Oak Creek, WI)

    2011-12-27T23:59:59.000Z

    A system and method for measuring and controlling stator winding temperature in an AC motor while idling is disclosed. The system includes a circuit having an input connectable to an AC source and an output connectable to an input terminal of a multi-phase AC motor. The circuit further includes a plurality of switching devices to control current flow and terminal voltages in the multi-phase AC motor and a controller connected to the circuit. The controller is configured to activate the plurality of switching devices to create a DC signal in an output of the motor control device corresponding to an input to the multi-phase AC motor, determine or estimate a stator winding resistance of the multi-phase AC motor based on the DC signal, and estimate a stator temperature from the stator winding resistance. Temperature can then be controlled and regulated by DC injection into the stator windings.

  4. Correlation between internal fiducial tumor motion and external marker motion for liver tumors imaged with 4D-CT

    SciTech Connect (OSTI)

    Beddar, A. Sam [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States)]. E-mail: abeddar@mdanderson.org; Kainz, Kristofer [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Briere, Tina Marie [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Tsunashima, Yoshikazu [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Pan Tinsu [Department of Diagnostic Imaging, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Prado, Karl [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Mohan, Radhe [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Gillin, Michael [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Krishnan, Sunil [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States)

    2007-02-01T23:59:59.000Z

    Purpose: We investigated the correlation between the motions of an external marker and internal fiducials implanted in the liver for 8 patients undergoing respiratory-based computed tomography (four-dimensional CT [4D-CT]) procedures. Methods and Materials: The internal fiducials were gold seeds, 3 mm in length and 1.2 mm in diameter. Four patients each had one implanted fiducial, and the other four had three implanted fiducials. The external marker was a plastic box, which is part of the Real-Time Position Management System (RPM) used to track the patient's respiration. Each patient received a standard helical CT scan followed by a time-correlated CT-image acquisition (4D-CT). The 4D-CT images were reconstructed in 10 separate phases covering the entire respiratory cycle. Results: The internal fiducial motion is predominant in the superior-inferior direction, with a range of 7.5-17.5 mm. The correlation between external respiration and internal fiducial motion is best during expiration. For 2 patients with their three fiducials separated by a maximum of 3.2 cm, the motions of the fiducials were well correlated, whereas for 2 patients with more widely spaced fiducials, there was less correlation. Conclusions: In general, there is a good correlation between internal fiducial motion imaged by 4D-CT and external marker motion. We have demonstrated that gating may be best performed at the end of the respiratory cycle. Special attention should be paid to gating for patients whose fiducials do not move in synchrony, because targeting on the correct respiratory amplitude alone would not guarantee that the entire tumor volume is within the treatment field.

  5. Copyright(c)2002 by Seoul National University Library. All rights reserved.(http://library.snu.ac.kr)

    E-Print Network [OSTI]

    .(http://library.snu.ac.kr) - 6 - 2.2.2 Dominance Based Crossover Operator for Evolutionary Multi-objective Algorithms [Rudenko et

  6. A modular VME or IBM PC based data acquisition system for multi-modality PET/CT scanners of different sizes and detector types

    E-Print Network [OSTI]

    Crosetto, D B

    2000-01-01T23:59:59.000Z

    A modular VME or IBM PC based data acquisition system for multi-modality PET/CT scanners of different sizes and detector types

  7. Real-time, programmable, digital signal-processing electronics for extracting the information from a detector module for multi-modality PET/SPECT/CT scanners

    E-Print Network [OSTI]

    Crosetto, D B

    2000-01-01T23:59:59.000Z

    Real-time, programmable, digital signal-processing electronics for extracting the information from a detector module for multi-modality PET/SPECT/CT scanners

  8. Stationary table CT dosimetry and anomalous scanner-reported values of CTDI{sub vol}

    SciTech Connect (OSTI)

    Dixon, Robert L., E-mail: rdixon@wfubmc.edu [Department of Radiology, Wake Forest University School of Medicine, Winston-Salem, North Carolina 27157 (United States); Boone, John M. [Departments of Radiology and Biomedical Engineering, University of California Davis, Sacramento, California 95817 (United States)] [Departments of Radiology and Biomedical Engineering, University of California Davis, Sacramento, California 95817 (United States)

    2014-01-15T23:59:59.000Z

    Purpose: Anomalous, scanner-reported values of CTDI{sub vol} for stationary phantom/table protocols (having elevated values of CTDI{sub vol} over 300% higher than the actual dose to the phantom) have been observed; which are well-beyond the typical accuracy expected of CTDI{sub vol} as a phantom dose. Recognition of these outliers as “bad data” is important to users of CT dose index tracking systems (e.g., ACR DIR), and a method for recognition and correction is provided. Methods: Rigorous methods and equations are presented which describe the dose distributions for stationary-table CT. A comparison with formulae for scanner-reported values of CTDI{sub vol} clearly identifies the source of these anomalies. Results: For the stationary table, use of the CTDI{sub 100} formula (applicable to a moving phantom only) overestimates the dose due to extra scatter and also includes an overbeaming correction, both of which are nonexistent when the phantom (or patient) is held stationary. The reported DLP remains robust for the stationary phantom. Conclusions: The CTDI-paradigm does not apply in the case of a stationary phantom and simpler nonintegral equations suffice. A method of correction of the currently reported CTDI{sub vol} using the approach-to-equilibrium formula H(a) and an overbeaming correction factor serves to scale the reported CTDI{sub vol} values to more accurate levels for stationary-table CT, as well as serving as an indicator in the detection of “bad data.”.

  9. SU-E-I-18: CT Scanner QA Using Normalized CTDI Ratio

    SciTech Connect (OSTI)

    Randazzo, M; Tambasco, M; Russell, B [San Diego State University, San Diego, CA (United States)

    2014-06-01T23:59:59.000Z

    Purpose: To create a ratio of weighted computed tomography dose index (CTDIw) data normalized to in-air measurements (CTDIair) as a function of beam quality to create a look-up table for frequent, rapid quality assurance (QA) checks of CTDI. Methods: The CTDIw values were measured according to TG-63 protocol using a pencil ionization chamber (Unfors Xi CT detector) and head and body Polymethyl methacrylate (PMMA) phantoms (16 and 32 cm diameter, respectively). Single scan dose profiles were measured at each clinically available energy (80,100,120,140 kVp) on three different CT scanners (two Siemens SOMATOM Definition Flash and one GE Optima), using a tube current of 400 mA, a one second rotation time, and the widest available beam width (32 × 0.6 mm and 16 × 1.25 mm, respectively). These values were normalized to CTDIair measurements using the same conditions as CTDIw. The ratios (expressed in cGy/R) were assessed for each scanner as a function of each energy's half value layer (HVL) paired with the phantom's appropriate bow tie filter measured in mmAl. Results: Normalized CTDI values vary linearly with HVL for both the head and body phantoms. The ratios for the two Siemens machines are very similar at each energy. Compared to the GE scanner, these values vary between 10–20% for each kVp setting. Differences in CTDIair contribute most to the deviation of the ratios across machines. Ratios are independent of both mAs and collimation. Conclusion: Look-up tables constructed of normalized CTDI values as a function of HVL can be used to derive CTDIw data from only three in-air measurements (one for CTDIair and two with added filtration for HVL) to allow for simple, frequent QA checks without CT phantom setup. Future investigations will involve comparing results with Monte Carlo simulations for validation.

  10. Specific recommendations for accurate and direct use of PET-CT in PET guided radiotherapy for head and neck sites

    SciTech Connect (OSTI)

    Thomas, C. M., E-mail: christopher.thomas@gstt.nhs.uk; Convery, D. J.; Greener, A. G. [Guy's and St. Thomas’ NHS Foundation Trust, Medical Physics Department, St. Thomas’ Hospital, London SE1 7EH (United Kingdom)] [Guy's and St. Thomas’ NHS Foundation Trust, Medical Physics Department, St. Thomas’ Hospital, London SE1 7EH (United Kingdom); Pike, L. C.; Baker, S.; Woods, E. [Division of Imaging Sciences and Biomedical Engineering, King's College London, King's Health Partners, St. Thomas’ Hospital, London SE1 7EH (United Kingdom)] [Division of Imaging Sciences and Biomedical Engineering, King's College London, King's Health Partners, St. Thomas’ Hospital, London SE1 7EH (United Kingdom); Hartill, C. E. [Guy's and St. Thomas’ NHS Foundation Trust, Radiotherapy, Clinical Outpatients Clinic, St. Thomas’ Hospital, London SE1 7EH (United Kingdom)] [Guy's and St. Thomas’ NHS Foundation Trust, Radiotherapy, Clinical Outpatients Clinic, St. Thomas’ Hospital, London SE1 7EH (United Kingdom)

    2014-04-15T23:59:59.000Z

    Purpose: To provide specific experience-based guidance and recommendations for centers wishing to develop, validate, and implement an accurate and efficient process for directly using positron emission tomography-computed tomography (PET-CT) for the radiotherapy planning of head and neck cancer patients. Methods: A PET-CT system was modified with hard-top couch, external lasers and radiotherapy immobilization and indexing devices and was subject to a commissioning and quality assurance program. PET-CT imaging protocols were developed specifically for radiotherapy planning and the image quality and pathway tested using phantoms and five patients recruited into an in-house study. Security and accuracy of data transfer was tested throughout the whole data pathway. The patient pathway was fully established and tested ready for implementation in a PET-guided dose-escalation trial for head and neck cancer patients. Results: Couch deflection was greater than for departmental CT simulator machines. An area of high attenuation in the couch generated image artifacts and adjustments were made accordingly. Using newly developed protocols CT image quality was suitable to maintain delineation and treatment accuracy. Upon transfer of data to the treatment planning system a half pixel offset between PET and CT was observed and corrected. By taking this into account, PET to CT alignment accuracy was maintained below 1 mm in all systems in the data pathway. Transfer of structures delineated in the PET fusion software to the radiotherapy treatment planning system was validated. Conclusions: A method to perform direct PET-guided radiotherapy planning was successfully validated and specific recommendations were developed to assist other centers. Of major concern is ensuring that the quality of PET and CT data is appropriate for radiotherapy treatment planning and on-treatment verification. Couch movements can be compromised, bore-size can be a limitation for certain immobilization techniques, laser positioning may affect setup accuracy and couch deflection may be greater than scanners dedicated to radiotherapy. The full set of departmental commissioning and routine quality assurance tests applied to radiotherapy CT simulators must be carried out on the PET-CT scanner. CT image quality must be optimized for radiotherapy planning whilst understanding that the appearance will differ between scanners and may affect delineation. PET-CT quality assurance schedules will need to be added to and modified to incorporate radiotherapy quality assurance. Methods of working for radiotherapy and PET staff will change to take into account considerations of both parties. PET to CT alignment must be subject to quality control on a loaded and unloaded couch preferably using a suitable emission phantom, and tested throughout the whole data pathway. Data integrity must be tested throughout the whole pathway and a system included to verify that delineated structures are transferred correctly. Excellent multidisciplinary team communication and working is vital, and key staff members on both sides should be specifically dedicated to the project. Patient pathway should be clearly devised to optimize patient care and the resources of all departments. Recruitment of a cohort of patients into a methodology study is valuable to test the quality assurance methods and pathway.

  11. Methods, systems and apparatus for controlling operation of two alternating current (AC) machines

    DOE Patents [OSTI]

    Gallegos-Lopez, Gabriel (Torrance, CA); Nagashima, James M. (Cerritos, CA); Perisic, Milun (Torrance, CA); Hiti, Silva (Redondo Beach, CA)

    2012-02-14T23:59:59.000Z

    A system is provided for controlling two AC machines. The system comprises a DC input voltage source that provides a DC input voltage, a voltage boost command control module (VBCCM), a five-phase PWM inverter module coupled to the two AC machines, and a boost converter coupled to the inverter module and the DC input voltage source. The boost converter is designed to supply a new DC input voltage to the inverter module having a value that is greater than or equal to a value of the DC input voltage. The VBCCM generates a boost command signal (BCS) based on modulation indexes from the two AC machines. The BCS controls the boost converter such that the boost converter generates the new DC input voltage in response to the BCS. When the two AC machines require additional voltage that exceeds the DC input voltage required to meet a combined target mechanical power required by the two AC machines, the BCS controls the boost converter to drive the new DC input voltage generated by the boost converter to a value greater than the DC input voltage.

  12. Implementation and commissioning of an integrated micro-CT/RT system with computerized independent jaw collimation

    SciTech Connect (OSTI)

    Jensen, Michael D. [Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada)] [Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Hrinivich, W. Thomas; Jung, Jongho A. [Department of Physics and Astronomy, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada)] [Department of Physics and Astronomy, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Holdsworth, David W. [Imaging Research Laboratories, Robarts Research Institute, 100 Perth Drive, London, Ontario N6A 5K8 (Canada) [Imaging Research Laboratories, Robarts Research Institute, 100 Perth Drive, London, Ontario N6A 5K8 (Canada); Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Department of Surgery, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Drangova, Maria [Imaging Research Laboratories, Robarts Research Institute, 100 Perth Drive, London, Ontario N6A 5K8, Canada and Department of Medical Biophysics, The University of Western Ontario 1151 Richmond Street, London, Ontario N6A 3K7 (Canada)] [Imaging Research Laboratories, Robarts Research Institute, 100 Perth Drive, London, Ontario N6A 5K8, Canada and Department of Medical Biophysics, The University of Western Ontario 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Chen, Jeff [Department of Physics and Engineering, London Regional Cancer Program, London Health Sciences Centre, 800 Commissioners Road East, London, Ontario N6A 5W9 (Canada) [Department of Physics and Engineering, London Regional Cancer Program, London Health Sciences Centre, 800 Commissioners Road East, London, Ontario N6A 5W9 (Canada); Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Department of Oncology, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Wong, Eugene [Department of Physics and Astronomy, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada) [Department of Physics and Astronomy, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Department of Medical Biophysics, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Department of Oncology, The University of Western Ontario, 1151 Richmond Street, London, Ontario N6A 3K7 (Canada); Department of Physics and Engineering, London Regional Cancer Program, London Health Sciences Centre, 800 Commissioners Road East, London, Ontario N6A 5W9 (Canada)

    2013-08-15T23:59:59.000Z

    Purpose: To design, construct, and commission a set of computer-controlled motorized jaws for a micro-CT/RT system to perform conformal image-guided small animal radiotherapy.Methods: The authors designed and evaluated a system of custom-built motorized orthogonal jaws, which allows the delivery of off-axis rectangular fields on a GE eXplore CT 120 preclinical imaging system. The jaws in the x direction are independently driven, while the y-direction jaws are symmetric. All motors have backup encoders, verifying jaw positions. Mechanical performance of the jaws was characterized. Square beam profiles ranging from 2 × 2 to 60 × 60 mm{sup 2} were measured using EBT2 film in the center of a 70 × 70 × 22 mm{sup 3} solid water block. Similarly, absolute depth dose was measured in a solid water and EBT2 film stack 50 × 50 × 50 mm{sup 3}. A calibrated Farmer ion chamber in a 70 × 70 × 20 mm{sup 3} solid water block was used to measure the output of three field sizes: 50 × 50, 40 × 40, and 30 × 30 mm{sup 2}. Elliptical target plans were delivered to films to assess overall system performance. Respiratory-gated treatment was implemented on the system and initially proved using a simple sinusoidal motion phantom. All films were scanned on a flatbed scanner (Epson 1000XL) and converted to dose using a fitted calibration curve. A Monte Carlo beam model of the micro-CT with the jaws has been created using BEAMnrc for comparison with the measurements. An example image-guided partial lung irradiation in a rat is demonstrated.Results: The averaged random error of positioning each jaw is less than 0.1 mm. Relative output factors measured with the ion chamber agree with Monte Carlo simulations within 2%. Beam profiles and absolute depth dose curves measured from the films agree with simulations within measurement uncertainty. Respiratory-gated treatments applied to a phantom moving with a peak-to-peak amplitude of 5 mm showed improved beam penumbra (80%–20%) from 3.9 to 0.8 mm.Conclusions: A set of computer-controlled motorized jaws for a micro-CT/RT system were constructed with position reliably better than a tenth of a millimeter. The hardware system is ready for image-guided conformal radiotherapy for small animals with capability of respiratory-gated delivery.

  13. Quantitative comparison of noise texture across CT scanners from different manufacturers

    SciTech Connect (OSTI)

    Solomon, Justin B.; Christianson, Olav; Samei, Ehsan [Carl E. Ravin Advanced Imaging Laboratories and Clinical Imaging Physics Group, Department of Radiology, Medical Physics Graduate Program, Duke University Medical Center, Durham, North Carolina 27705 (United States); Carl E. Ravin Advanced Imaging Laboratories and Clinical Imaging Physics Group, Department of Radiology, Duke University Medical Center, Durham, North Carolina 27705 (United States); Carl E. Ravin Advanced Imaging Laboratories and Clinical Imaging Physics Group, Medical Physics Graduate Program, Departments of Radiology, Physics, Biomedical Engineering, and Electrical and Computer Engineering, Duke University, Durham, North Carolina 27705 (United States)

    2012-10-15T23:59:59.000Z

    Purpose: To quantitatively compare noise texture across computed tomography (CT) scanners from different manufacturers using the noise power spectrum (NPS). Methods: The American College of Radiology CT accreditation phantom (Gammex 464, Gammex, Inc., Middleton, WI) was imaged on two scanners: Discovery CT 750HD (GE Healthcare, Waukesha, WI), and SOMATOM Definition Flash (Siemens Healthcare, Germany), using a consistent acquisition protocol (120 kVp, 0.625/0.6 mm slice thickness, 250 mAs, and 22 cm field of view). Images were reconstructed using filtered backprojection and a wide selection of reconstruction kernels. For each image set, the 2D NPS were estimated from the uniform section of the phantom. The 2D spectra were normalized by their integral value, radially averaged, and filtered by the human visual response function. A systematic kernel-by-kernel comparison across manufacturers was performed by computing the root mean square difference (RMSD) and the peak frequency difference (PFD) between the NPS from different kernels. GE and Siemens kernels were compared and kernel pairs that minimized the RMSD and |PFD| were identified. Results: The RMSD (|PFD|) values between the NPS of GE and Siemens kernels varied from 0.01 mm{sup 2} (0.002 mm{sup -1}) to 0.29 mm{sup 2} (0.74 mm{sup -1}). The GE kernels 'Soft,''Standard,''Chest,' and 'Lung' closely matched the Siemens kernels 'B35f,''B43f,''B41f,' and 'B80f' (RMSD < 0.05 mm{sup 2}, |PFD| < 0.02 mm{sup -1}, respectively). The GE 'Bone,''Bone+,' and 'Edge' kernels all matched most closely with Siemens 'B75f' kernel but with sizeable RMSD and |PFD| values up to 0.18 mm{sup 2} and 0.41 mm{sup -1}, respectively. These sizeable RMSD and |PFD| values corresponded to visually perceivable differences in the noise texture of the images. Conclusions: It is possible to use the NPS to quantitatively compare noise texture across CT systems. The degree to which similar texture across scanners could be achieved varies and is limited by the kernels available on each scanner.

  14. Improving best-phase image quality in cardiac CT by motion correction with MAM optimization

    SciTech Connect (OSTI)

    Rohkohl, Christopher; Bruder, Herbert; Stierstorfer, Karl [Siemens AG, Healthcare Sector, Siemensstrasse 1, 91301 Forchheim (Germany); Flohr, Thomas [Siemens AG, Healthcare Sector, Siemensstrasse 1, 91301 Forchheim (Germany); Institute of Diagnostic Radiology, Eberhard Karls University, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany)

    2013-03-15T23:59:59.000Z

    Purpose: Research in image reconstruction for cardiac CT aims at using motion correction algorithms to improve the image quality of the coronary arteries. The key to those algorithms is motion estimation, which is currently based on 3-D/3-D registration to align the structures of interest in images acquired in multiple heart phases. The need for an extended scan data range covering several heart phases is critical in terms of radiation dose to the patient and limits the clinical potential of the method. Furthermore, literature reports only slight quality improvements of the motion corrected images when compared to the most quiet phase (best-phase) that was actually used for motion estimation. In this paper a motion estimation algorithm is proposed which does not require an extended scan range but works with a short scan data interval, and which markedly improves the best-phase image quality. Methods: Motion estimation is based on the definition of motion artifact metrics (MAM) to quantify motion artifacts in a 3-D reconstructed image volume. The authors use two different MAMs, entropy, and positivity. By adjusting the motion field parameters, the MAM of the resulting motion-compensated reconstruction is optimized using a gradient descent procedure. In this way motion artifacts are minimized. For a fast and practical implementation, only analytical methods are used for motion estimation and compensation. Both the MAM-optimization and a 3-D/3-D registration-based motion estimation algorithm were investigated by means of a computer-simulated vessel with a cardiac motion profile. Image quality was evaluated using normalized cross-correlation (NCC) with the ground truth template and root-mean-square deviation (RMSD). Four coronary CT angiography patient cases were reconstructed to evaluate the clinical performance of the proposed method. Results: For the MAM-approach, the best-phase image quality could be improved for all investigated heart phases, with a maximum improvement of the NCC value by 100% and of the RMSD value by 81%. The corresponding maximum improvements for the registration-based approach were 20% and 40%. In phases with very rapid motion the registration-based algorithm obtained better image quality, while the image quality of the MAM algorithm was superior in phases with less motion. The image quality improvement of the MAM optimization was visually confirmed for the different clinical cases. Conclusions: The proposed method allows a software-based best-phase image quality improvement in coronary CT angiography. A short scan data interval at the target heart phase is sufficient, no additional scan data in other cardiac phases are required. The algorithm is therefore directly applicable to any standard cardiac CT acquisition protocol.

  15. DOE - Office of Legacy Management -- Metals Selling Corp - CT 0-01

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp - CT 0-01 FUSRAP Considered Sites Site:

  16. DOE - Office of Legacy Management -- New England Lime Co - CT 10

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp - CT 0-01Naturita36 SupplyCanaan Site

  17. DOE - Office of Legacy Management -- Olin Mathieson - CT 0-02

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp - CT 0-01Naturita36NewNortonOhmart

  18. A comparison of CT- and ultrasound-based imaging to localize the prostate for external beam radiotherapy

    SciTech Connect (OSTI)

    McNair, Helen A. [Department of Radiotherapy, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom)]. E-mail: Helen.McNair@rmh.nhs.uk; Mangar, Stephen A. [Department of Academic Urology Unit, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Coffey, Jerome [Department of Academic Urology Unit, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Shoulders, Beverley [Department of Radiotherapy, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Hansen, Vibeke N. [Department of Physics, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Norman, Andrew [Department of Radiotherapy, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Department of Physics, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Department of Radiology, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Department of Academic Urology Unit, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Staffurth, John [Department of Academic Urology Unit, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Sohaib, S. Aslam [Department of Radiology, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Warrington, Alan P. [Department of Physics, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom); Dearnaley, David P. [Department of Academic Urology Unit, Royal Marsden NHS Foundation Trust, Sutton (United Kingdom)

    2006-07-01T23:59:59.000Z

    Purpose: This study assesses the accuracy of NOMOS B-mode acquisition and targeting system (BAT) compared with computed tomography (CT) in localizing the prostate. Methods and Materials: Twenty-six patients were CT scanned, and the prostate was localized by 3 observers using the BAT system. The BAT couch shift measurements were compared with the CT localization. Six of the patients had gold markers present in the prostate, and the prostate movement determined by BAT was compared with the movement determined by the gold markers. Results: Using the BAT system, the 3 observers determined the prostate position to be a mean of 1-5 mm over all directions with respect to the CT. The proportion of readings with a difference >3 mm between the observers was in the range of 25% to 44%. The prostate movement based on gold markers was an average of 3-5 mm different from that measured by BAT. The literature assessing the accuracy and reproducibility on BAT is summarized and compared with our findings. Conclusions: We have found that there are systematic differences between the BAT-defined prostate position compared with that estimated on CT using gold grain marker seeds.

  19. SU-E-T-99: Design and Development of Isocenter Parameter System for CT Simulation Laser Based On DICOM RT

    SciTech Connect (OSTI)

    Luo, G [Sun Yat-sen University Cancer Center, State Key Laboratory of Oncology in South China (China)

    2014-06-01T23:59:59.000Z

    Purpose: In order to receive DICOM files from treatment planning system and generate patient isocenter positioning parameter file for CT laser system automatically, this paper presents a method for communication with treatment planning system and calculation of isocenter parameter for each radiation field. Methods: Coordinate transformation and laser positioning file formats were analyzed, isocenter parameter was calculated via data from DICOM CT Data and DICOM RTPLAN file. An in-house software-DicomGenie was developed based on the object-oriented program platform-Qt with DCMTK SDK (Germany OFFIS company DICOM SDK) . DicomGenie was tested for accuracy using Philips CT simulation plan system (Tumor LOC, Philips) and A2J CT positioning laser system (Thorigny Sur Marne, France). Results: DicomGenie successfully established DICOM communication between treatment planning system, DICOM files were received by DicomGenie and patient laser isocenter information was generated accurately. Patient laser parameter data files can be used for for CT laser system directly. Conclusion: In-house software DicomGenie received and extracted DICOM data, isocenter laser positioning data files were created by DicomGenie and can be use for A2J laser positioning system.

  20. Continuous Hyperplastic Models for Overconsolidated ClaysContinuous Hyperplastic Models for Overconsolidated Clays Visit us at: "www.technion.ac.il" and "www-civil.eng.ox.ac.uk"

    E-Print Network [OSTI]

    Houlsby, Guy T.

    Continuous Hyperplastic Models for Overconsolidated ClaysContinuous Hyperplastic Models for Overconsolidated Clays Visit us at: "www.technion.ac.il" and "www-civil.eng.ox.ac.uk" I. Einav and A.M. Puzrin for the formulation of realistic models for the triaxial behaviour of overconsolidated clays at both small and large

  1. Methods, systems and apparatus for controlling operation of two alternating current (AC) machines

    DOE Patents [OSTI]

    Gallegos-Lopez, Gabriel (Torrance, CA); Nagashima, James M. (Cerritos, CA); Perisic, Milun (Torrance, CA); Hiti, Silva (Redondo Beach, CA)

    2012-06-05T23:59:59.000Z

    A system is provided for controlling two alternating current (AC) machines via a five-phase PWM inverter module. The system comprises a first control loop, a second control loop, and a current command adjustment module. The current command adjustment module operates in conjunction with the first control loop and the second control loop to continuously adjust current command signals that control the first AC machine and the second AC machine such that they share the input voltage available to them without compromising the target mechanical output power of either machine. This way, even when the phase voltage available to either one of the machines decreases, that machine outputs its target mechanical output power.

  2. A system for tranmitting low frequency analog signals over ac power lines

    DOE Patents [OSTI]

    Baker, S.P.; Durall, R.L.; Haynes, H.D.

    1987-07-30T23:59:59.000Z

    A system for transmitting low frequency analog signals over ac power lines using FM modulation. A low frequency analog signal to be transmitted is first applied to a voltage-to-frequency converter where it is converted to a signal whose frequency varies in proportion to the analog signal amplitude. This signal is then used to modulate the carrier frequency of an FM transmitter coupled to an ac power line. The modulation signal frequency range is selected to be within the response band of the FM transmitter. The FM modulated carrier signal is received by an FM receiver coupled to the ac power line, demodulated and the demodulated signal frequency is converted by a frequency-to-voltage converter back to the form of the original low frequency analog input signal. 4 figs.

  3. Quantum recurrence and fractional dynamic localization in ac-driven perfect state transfer Hamiltonians

    SciTech Connect (OSTI)

    Longhi, Stefano, E-mail: stefano.longhi@fisi.polimi.it

    2014-06-15T23:59:59.000Z

    Quantum recurrence and dynamic localization are investigated in a class of ac-driven tight-binding Hamiltonians, the Krawtchouk quantum chain, which in the undriven case provides a paradigmatic Hamiltonian model that realizes perfect quantum state transfer and mirror inversion. The equivalence between the ac-driven single-particle Krawtchouk Hamiltonian H{sup -hat} (t) and the non-interacting ac-driven bosonic junction Hamiltonian enables to determine in a closed form the quasi energy spectrum of H{sup -hat} (t) and the conditions for exact wave packet reconstruction (dynamic localization). In particular, we show that quantum recurrence, which is predicted by the general quantum recurrence theorem, is exact for the Krawtchouk quantum chain in a dense range of the driving amplitude. Exact quantum recurrence provides perfect wave packet reconstruction at a frequency which is fractional than the driving frequency, a phenomenon that can be referred to as fractional dynamic localization.

  4. Low AC Loss YBCO Coated Conductor Geometry by Direct Inkjet Printing

    SciTech Connect (OSTI)

    Rupich, Martin, Dr. [American Superconductor Corporation; Duckworth, Robert, Dr. [Oak Ridge National Laboratory

    2009-10-01T23:59:59.000Z

    The second generation (2G) high temperature superconductors (HTS) wire offers potential benefits for many electric power applications, including ones requiring filamentized conductors with low ac loss, such as transformers and fault current limiters. However, the use of 2G wire in these applications requires the development of both novel multi-filamentary conductor designs with lower ac losses and the development of advanced manufacturing technologies that enable the low-cost manufacturing of these filamentized architectures. This Phase I SBIR project focused on testing inkjet printing as a potential low-cost, roll-to-roll manufacturing technique to fabricate potential low ac loss filamentized architectures directly on the 2G template strips.

  5. Technical Note: Precision and accuracy of a commercially available CT optically stimulated luminescent dosimetry system for the measurement of CT dose index

    SciTech Connect (OSTI)

    Vrieze, Thomas J.; Sturchio, Glenn M.; McCollough, Cynthia H. [Department of Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States); Department of Medicine, Mayo Clinic, Rochester, Minnesota 55905 (United States); Department of Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States)

    2012-11-15T23:59:59.000Z

    Purpose: To determine the precision and accuracy of CTDI{sub 100} measurements made using commercially available optically stimulated luminescent (OSL) dosimeters (Landaur, Inc.) as beam width, tube potential, and attenuating material were varied. Methods: One hundred forty OSL dosimeters were individually exposed to a single axial CT scan, either in air, a 16-cm (head), or 32-cm (body) CTDI phantom at both center and peripheral positions. Scans were performed using nominal total beam widths of 3.6, 6, 19.2, and 28.8 mm at 120 kV and 28.8 mm at 80 kV. Five measurements were made for each of 28 parameter combinations. Measurements were made under the same conditions using a 100-mm long CTDI ion chamber. Exposed OSL dosimeters were returned to the manufacturer, who reported dose to air (in mGy) as a function of distance along the probe, integrated dose, and CTDI{sub 100}. Results: The mean precision averaged over 28 datasets containing five measurements each was 1.4%{+-} 0.6%, range = 0.6%-2.7% for OSL and 0.08%{+-} 0.06%, range = 0.02%-0.3% for ion chamber. The root mean square (RMS) percent differences between OSL and ion chamber CTDI{sub 100} values were 13.8%, 6.4%, and 8.7% for in-air, head, and body measurements, respectively, with an overall RMS percent difference of 10.1%. OSL underestimated CTDI{sub 100} relative to the ion chamber 21/28 times (75%). After manual correction of the 80 kV measurements, the RMS percent differences between OSL and ion chamber measurements were 9.9% and 10.0% for 80 and 120 kV, respectively. Conclusions: Measurements of CTDI{sub 100} with commercially available CT OSL dosimeters had a percent standard deviation of 1.4%. After energy-dependent correction factors were applied, the RMS percent difference in the measured CTDI{sub 100} values was about 10%, with a tendency of OSL to underestimate CTDI relative to the ion chamber. Unlike ion chamber methods, however, OSL dosimeters allow measurement of the radiation dose profile.

  6. Operated by the Association of Universities for Research in Astronomy, Inc., for the National Aeronautics and Space Administration Instrument Science Report ACS 2005-06

    E-Print Network [OSTI]

    Sirianni, Marco

    Aeronautics and Space Administration Instrument Science Report ACS 2005-06 Demonstration of a Significant examples where major scien- #12;Instrument Science Report ACS 2005-06 2 tific discoveries have only been

  7. Percutaneous Extraction of Cement Leakage After Vertebroplasty Under CT and Fluoroscopy Guidance: A New Technique

    SciTech Connect (OSTI)

    Amoretti, Nicolas, E-mail: amorettinicolas@yahoo.fr; Huwart, Laurent, E-mail: huwart.laurent@wanadoo.fr [Centre Hospitalo-Universitaire de Nice, Department of Radiology (France)

    2012-12-15T23:59:59.000Z

    Purpose: We report a new minimally invasive technique of extraction of cement leakage following percutaneous vertebroplasty in adults. Methods: Seven adult patients (five women, two men; mean age: 81 years) treated for vertebral compression fractures by percutaneous vertebroplasty had cement leakage into perivertebral soft tissues along the needle route. Immediately after vertebroplasty, the procedure of extraction was performed under computed tomography (CT) and fluoroscopy guidance: a Chiba needle was first inserted using the same route as the vertebroplasty until contact was obtained with the cement fragment. This needle was then used as a guide for an 11-gauge Trocar t'am (Thiebaud, France). After needle withdrawal, a 13-gauge endoscopy clamp was inserted through the cannula to extract the cement fragments. The whole procedure was performed under local anesthesia. Results: In each patient, all cement fragments were withdrawn within 10 min, without complication. Conclusions: This report suggests that this CT- and fluoroscopy-guided percutaneous technique of extraction could reduce the rate of cement leakage-related complications.

  8. Sparse signal reconstruction from polychromatic X-ray CT measurements via mass attenuation discretization

    SciTech Connect (OSTI)

    Gu, Renliang; Dogandži?, Aleksandar [Iowa State University, Center for Nondestructive Evaluation, 1915 Scholl Road, Ames, IA 50011 (United States)

    2014-02-18T23:59:59.000Z

    We propose a method for reconstructing sparse images from polychromatic x-ray computed tomography (ct) measurements via mass attenuation coefficient discretization. The material of the inspected object and the incident spectrum are assumed to be unknown. We rewrite the Lambert-Beer’s law in terms of integral expressions of mass attenuation and discretize the resulting integrals. We then present a penalized constrained least-squares optimization approach for reconstructing the underlying object from log-domain measurements, where an active set approach is employed to estimate incident energy density parameters and the nonnegativity and sparsity of the image density map are imposed using negative-energy and smooth ?{sub 1}-norm penalty terms. We propose a two-step scheme for refining the mass attenuation discretization grid by using higher sampling rate over the range with higher photon energy, and eliminating the discretization points that have little effect on accuracy of the forward projection model. This refinement allows us to successfully handle the characteristic lines (Dirac impulses) in the incident energy density spectrum. We compare the proposed method with the standard filtered backprojection, which ignores the polychromatic nature of the measurements and sparsity of the image density map. Numerical simulations using both realistic simulated and real x-ray ct data are presented.

  9. Patients with Life-Threatening Arterial Renal Hemorrhage: CT Angiography and Catheter Angiography with Subsequent Superselective Embolization

    SciTech Connect (OSTI)

    Sommer, C. M., E-mail: christof.sommer@med.uni-heidelberg.de; Stampfl, U.; Bellemann, N.; Ramsauer, S. [University Hospital Heidelberg, Department of Diagnostic and Interventional Radiology (Germany); Loenard, B. M. [University Hospital Heidelberg, Department of Urology (Germany); Haferkamp, A. [University Hospital Heidelberg, Department of Anesthesiology (Germany); Hallscheidt, P.; Richter, G. M.; Kauczor, H. U.; Radeleff, B. A. [University Hospital Heidelberg, Department of Diagnostic and Interventional Radiology (Germany)

    2010-06-15T23:59:59.000Z

    The purpose of this study was to evaluate the technical and clinical success of superselective embolization in patients with life-threatening arterial renal hemorrhage undergoing preinterventional CT angiography. Forty-three patients with clinical signs of life-threatening arterial renal hemorrhage underwent CT angiography and catheter angiography. Superselective embolization was indicated in the case of a positive catheter angiography. Primary study goals were technical and clinical success of superselective embolization. Secondary study goals were CT angiographic and catheter angiographic image findings and clinical follow-up. The mean time interval between CT angiography and catheter angiography was 8.3 {+-} 10.3 h (range, 0.2-34.1 h). Arterial renal hemorrhage was identified with CT angiography in 42 of 43 patients (98%) and catheter angiography in 39 of 43 patients (91%) (overview angiography in 4 of 43 patients [9%], selective angiography in 16 of 43 patients [37%], and superselective angiography in 39 of 43 patients [91%]). Superselective embolization was performed in 39 of 43 patients (91%) and technically successful in 37 of 39 patients (95%). Therefore, coil embolization was performed in 13 of 37 patients (35%), liquid embolization in 9 of 37 patients (24%), particulate embolization in 1 of 37 patients (3%), and a combination in 14 of 37 patients (38%). Clinical failure occurred in 8 of 39 patients (21%) and procedure-related complications in 2 of 39 patients (5%). The 30-day mortality rate was 3%. Hemoglobin decreased significantly prior to intervention (P < 0.001) and increased significantly after intervention (P < 0.005). In conclusion, superselective embolization is effective, reliable, and safe in patients with life-threatening arterial renal hemorrhage. In contrast to overview and selective angiography, only superselective angiography allows reliable detection of arterial renal hemorrhage. Preinterventional CT angiography is excellent for detection and localization of arterial renal hemorrhage and appropriate for guidance of the embolization procedure.

  10. Radiofrequency Ablation Assisted by Real-Time Virtual Sonography and CT for Hepatocellular Carcinoma Undetectable by Conventional Sonography

    SciTech Connect (OSTI)

    Nakai, Motoki, E-mail: momonga@wakayama-med.ac.jp; Sato, Morio; Sahara, Shinya; Takasaka, Isao; Kawai, Nobuyuki; Minamiguchi, Hiroki; Tanihata, Hirohiko; Kimura, Masashi [Wakayama Medical University, Department of Radiology (Japan); Takeuchi, Nozomu [Hidaka General Hospital, Department of Radiology (Japan)

    2009-01-15T23:59:59.000Z

    Real-time virtual sonography (RVS) is a diagnostic imaging support system, which provides the same cross-sectional multiplanar reconstruction images as ultrasound images on the same monitor screen in real time. The purpose of this study was to evaluate radiofrequency ablation (RFA) assisted by RVS and CT for hepatocellular carcinoma (HCC) undetectable with conventional sonography. Subjects were 20 patients with 20 HCC nodules not detected by conventional sonography but detectable by CT or MRI. All patients had hepatitis C-induced liver cirrhosis; there were 13 males and 7 females aged 55-81 years (mean, 69.3 years). RFA was performed in the CT room, and the tumor was punctured with the assistance of RVS. CT was performed immediately after puncture, and ablation was performed after confirming that the needle had been inserted into the tumor precisely. The mean number of punctures and success rates of the first puncture were evaluated. Treatment effects were evaluated with dynamic CT every 3 months after RFA. RFA was technically feasible and local tumor control was achieved in all patients. The mean number of punctures was 1.1, and the success rate of the first puncture was 90.0%. This method enabled safe ablation without complications. The mean follow-up period was 13.5 month (range, 9-18 months). No local recurrence was observed at the follow-up points. In conclusion, RFA assisted by RVS and CT is a safe and efficacious method of treatment for HCC undetectable by conventional sonography.

  11. Beam Sampling for the Infinite Hidden Markov Model Jurgen Van Gael jv279@cam.ac.uk

    E-Print Network [OSTI]

    Ghahramani, Zoubin

    267@cam.ac.uk Department of Engineering, University of Cambridge, Cambridge CB2 1PZ, UK Yee Whye Teh Zoubin Ghahramani zoubin@eng.cam.ac.uk Department of Engineering, University of Cambridge, Cambridge CB2 models (Es- cobar & West, 1995; Rasmussen, 2000) for cluster- ing heterogeneous data and density

  12. The role of eddy currents and nanoparticle size on AC magnetic fieldinduced reflow in solder/magnetic nanocomposites

    E-Print Network [OSTI]

    McHenry, Michael E.

    The role of eddy currents and nanoparticle size on AC magnetic field­induced reflow in solder://jap.aip.org/about/rights_and_permissions #12;The role of eddy currents and nanoparticle size on AC magnetic field­induced reflow in solder be derived from eddy current losses in Cu planes in the substrate board. Eddy current heating in Cu sheets

  13. AC 263,222 for red rice control in soybeans and its potential injury to rice in a rotation

    E-Print Network [OSTI]

    Grymes, Charles Frost

    1993-01-01T23:59:59.000Z

    Field studies were conducted in 1991 and 1992 to evaluate the response of soybean, red rice, and rice the following year to AC 263,222 applied alone and in tank mixtures with imazethapyr or imazaquin. In 1991, AC 263,222 applied alone at 18, 36...

  14. Contact: Julie Goode, 0114 222 7018, j.k.goode@sheffield.ac.uk Interpersonal Skills for Community Support

    E-Print Network [OSTI]

    Stevenson, Mark

    revision guides, Kirby Lonsdale #12;Contact: Julie Goode, 0114 222 7018, j.k.goode@sheffield.ac.uk Study: · An awareness of good study practice in higher education; · Experience of communicating effectively, in bothContact: Julie Goode, 0114 222 7018, j.k.goode@sheffield.ac.uk Interpersonal Skills for Community

  15. Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830

    E-Print Network [OSTI]

    PNNL-20162 Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830 Cultural February 2011 Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830 Pacific Northwest is required. · Please be sure that any PDF submitted to DAHP has its cover sheet, figures, graphics

  16. IEEE ELECTRON DEVICE LETTERS, VOL. 18, NO. 2, FEBRUARY 1997 39 AC Hot-Carrier-Induced Degradation in

    E-Print Network [OSTI]

    Ng, Wai Tung

    IEEE ELECTRON DEVICE LETTERS, VOL. 18, NO. 2, FEBRUARY 1997 39 AC Hot-Carrier-Induced Degradation--Frequency-dependent ac-stress-induced degradation in NMOSFET's with N2O-grown and N2O-nitrided gate oxides was investigated. Suppressed device degradation is observed in both N2O-based devices as compared to SiO2 device

  17. Dynamic magnetization states of a spin valve in the presence of dc and ac currents: Synchronization, modification, and chaos

    E-Print Network [OSTI]

    Li, Charles

    Dynamic magnetization states of a spin valve in the presence of dc and ac currents: Synchronization and numerical calculations of dynamic magnetization states of a spin valve in the presence of dc and ac currents are expected to appear. In this paper, we consider a simple spin valve as a model system to study the problem

  18. STFC Introductory Summer School m.j.owens@reading.ac.uk18 Sept 2012 Solar Variability and

    E-Print Network [OSTI]

    STFC Introductory Summer School m.j.owens@reading.ac.uk18 Sept 2012 Solar Variability and Climate · The climate system · Solar variability · Solar effects on climate ­ Regional and global effects · The future? #12;STFC Introductory Summer School m.j.owens@reading.ac.uk Climate system #12;The source of much

  19. ACS Div of Fuel Chem Preprints 44:4, 1016-1019 (August, 1999) KINETICS OF HIGH PRESSURE CHAR OXIDATION

    E-Print Network [OSTI]

    Fletcher, Thomas H.

    ACS Div of Fuel Chem Preprints 44:4, 1016-1019 (August, 1999) KINETICS OF HIGH PRESSURE CHAR) by devolatilizing Pittsburgh #8 coal at #12;ACS Div of Fuel Chem Preprints 44:4, 1016-1019 (August, 1999) high

  20. 1 / 8 _atmark_@ http://www.zenhokyo.jp/index.html murasima-tky_atmark_umin.ac.jp

    E-Print Network [OSTI]

    Imai, Hiroshi

    3 (ERS) (CEE) (ITS) (CIDIR) http://icus.iis.u- tokyo.ac.jp/rnet_edr/index.php 3.11net2 ( 3.11net http://icus.iis.u- tokyo.ac.jp/rnet_edr/index.php 3.11net URL ( #12;

  1. Electric field and losses at AC self field mode in MF composites

    SciTech Connect (OSTI)

    Fukui, S.; Hlasnik, I.; Tsukamoto, O.; Amemiya, N. (Yokohama National Univ. (Japan)); Polak, M.; Kottman, P. (Slovak Academy of Science, Bratislava (Slovakia). Inst. of Electrical Engineering)

    1994-07-01T23:59:59.000Z

    Studies of the current-voltage characteristics of typical superconducting wires under static and dynamic conditions up to 50 Hz frequency have revealed much higher instantaneous local loss power densities in an external DC magnetic field than those which occur by magnetization in a transverse AC magnetic field. In this paper, the measured loss characteristics are compared with theoretical ones derived from the critical state model, and the self field AC loss are also estimated. Possible errors that can result by applying the critical state model are discussed.

  2. A robust coordinated control scheme for HVDC transmission with parallel AC systems

    SciTech Connect (OSTI)

    To, K.W.V.; David, A.K. (Hong Kong Polytechnic (Hong Kong). Dept. of Electrical Engineering); Hammad, A.E. (N.E. Swiss Power Co., Baden (Switzerland))

    1994-07-01T23:59:59.000Z

    This paper introduces a practical control philosophy for HVDC transmission in parallel operation to an AC system with particular emphasis on coordination of both transient and dynamic stability. Systematic development of the control scheme on the basis of on-line identification, optimal control and rule-based bang-optimal coordination principles is presented. Verification tests of the scheme on a physical HVDC/AC system simulator show that the simple control computer algorithm is practical and robust. The controller can successfully distinguish between different system fault severities and adapts its output signals to provide maximum synchronizing torque and ensure optimal damping of power oscillations.

  3. SU-E-J-113: The Influence of Optimizing Pediatric CT Simulator Protocols On the Treatment Dose Calculation in Radiotherapy

    SciTech Connect (OSTI)

    Zhang, Y; Zhang, J; Hu, Q; Tie, J; Wu, H [Key Laboratory of Carcinogenesis and Translational Research (Ministry of Education), Department of Radiotherapy, Peking University Cancer Hospital ' Institute, Beijing (China); Deng, J [Department of Therapeutic Radiology, Yale University, New Haven, CT (United States)

    2014-06-01T23:59:59.000Z

    Purpose: To investigate the possibility of applying optimized scanning protocols for pediatric CT simulation by quantifying the dosimetric inaccuracy introduced by using a fixed HU to density conversion. Methods: The images of a CIRS electron density reference phantom (Model 062) were acquired by a Siemens CT simulator (Sensation Open) using the following settings of tube voltage and beam current: 120 kV/190mA (the reference protocol used to calibrate CT for our treatment planning system (TPS)); Fixed 190mA combined with all available kV: 80, 100, and 140; fixed 120 kV and various current from 37 to 444 mA (scanner extremes) with interval of 30 mA. To avoid the HU uncertainty of point sampling in the various inserts of known electron densities, the mean CT numbers of the central cylindrical volume were calculated using DICOMan software. The doses per 100 MU to the reference point (SAD=100cm, Depth=10cm, Field=10X10cm, 6MV photon beam) in a virtual cubic phantom (30X30X30cm) were calculated using Eclipse TPS (calculation model: AcurosXB-11031) by assigning the CT numbers to HU of typical materials acquired by various protocols. Results: For the inserts of densities less than muscle, CT number fluctuations of all protocols were within the tolerance of 10 HU as accepted by AAPM-TG66. For more condensed materials, fixed kV yielded stable HU with any mA combination where largest disparities were found in 1750mg/cc insert: HU{sub reference}=1801(106.6cGy), HU{sub minimum}=1799 (106.6cGy, error{sub dose}=0.00%), HU{sub maximum}=1815 (106.8cGy, error{sub dose}=0.19%). Yet greater disagreements were observed with increasing density when kV was modified: HU{sub minimum}=1646 (104.5cGy, error{sub dose}=- 1.97%), HU{sub maximum}=2487 (116.4cGy, error{sub dose}=9.19%) in 1750mg/cc insert. Conclusion: Without affecting treatment dose calculation, personalized mA optimization of CT simulator can be conducted by fixing kV for a better cost-effectiveness of imaging dose and quality especially for children. Unless recalibrated, kV should be constant for all anatomical sites if diagnostic CT scanner is used as a simulator. This work was partially supported by Capital Medical Development Scientific Research Fund of China.

  4. M. P. Craven, L. Pecchia & J. L. Martin michael.craven@nottingham.ac.uk

    E-Print Network [OSTI]

    Oakley, Jeremy

    in image-guided surgery that is required to fulfill clinical and technical outcomes for multiple user needs with fluoroscopy, CT, MRI, Ultrasound imaging modalities. Extract clinical outcome measures. Collaboration on a new in neurosurgery · Other complications considered Vascular injury Radiation injury Summary of clinical outcomes

  5. The U.S. Nuclear Waste Technical Review Board evaluates the technical and scientific validity of ac-

    E-Print Network [OSTI]

    Chapter 1 Overview The U.S. Nuclear Waste Technical Review Board evaluates the technical in Nevada for its suit- ability as a location for a repository for high-level ra- dioactive waste (HLW) and spent nuclear fuel (SNF). The U.S. Department of Energy (DOE) began studying Yucca Mountain

  6. International Conference on Fully 3D Reconstruction in Radiology and Nuclear Medicine, Linau, Germany, July 9-13, 2007 Abstract--Four-dimensional computed tomography (4D-CT)

    E-Print Network [OSTI]

    , Germany, July 9-13, 2007 Abstract--Four-dimensional computed tomography (4D-CT) plays an important role computed tomography (4D-CT) with respiratory gating provides dynamic volume imaging datasets of the moving

  7. Objective index of image fidelity for JPEG2000 compressed body CT images

    SciTech Connect (OSTI)

    Kim, Kil Joong; Lee, Kyoung Ho; Kang, Heung-Sik; Kim, So Yeon; Kim, Young Hoon; Kim, Bohyoung; Seo, Jinwook; Mantiuk, Rafal [Department of Radiation Applied Life Science, Seoul National University College of Medicine, 28 Yongon-dong, Chongno-gu, Seoul, 110-744 (Korea, Republic of); Department of Radiology, Seoul National University Bundang Hospital, Seoul National University College of Medicine, Institute of Radiation Medicine, and Seoul National University Medical Research Center, 300 Gumi-dong, Bundang-gu, Seongnam-si, Gyeonggido, 463-707 (Korea, Republic of); School of Computer Science and Engineering, Seoul National University, 599 Gwanak-Ro, Gwanak-Gu, Seoul, 151-744 (Korea, Republic of); Department of Computer Science, University of British Columbia, 201-2366 Main Mall, Vancouver, British Columbia V6T 1Z4 (Canada)

    2009-07-15T23:59:59.000Z

    Compression ratio (CR) has been the de facto standard index of compression level for medical images. The aim of the study is to evaluate the CR, peak signal-to-noise ratio (PSNR), and a perceptual quality metric (high-dynamic range visual difference predictor HDR-VDP) as objective indices of image fidelity for Joint Photographic Experts Group (JPEG) 2000 compressed body computed tomography (CT) images, from the viewpoint of visually lossless compression approach. A total of 250 body CT images obtained with five different scan protocols (5-mm-thick abdomen, 0.67-mm-thick abdomen, 5-mm-thick lung, 0.67-mm-thick lung, and 5-mm-thick low-dose lung) were compressed to one of five CRs (reversible, 6:1, 8:1, 10:1, and 15:1). The PSNR and HDR-VDP values were calculated for the 250 pairs of the original and compressed images. By alternately displaying an original and its compressed image on the same monitor, five radiologists independently determined if the pair was distinguishable or indistinguishable. The kappa statistic for the interobserver agreement among the five radiologists' responses was 0.70. According to the radiologists' responses, the number of distinguishable image pairs tended to significantly differ among the five scan protocols at 6:1-10:1 compressions (Fisher-Freeman-Halton exact tests). Spearman's correlation coefficients between each of the CR, PSNR, and HDR-VDP and the number of radiologists who responded as distinguishable were 0.72, -0.77, and 0.85, respectively. Using the radiologists' pooled responses as the reference standards, the areas under the receiver-operating-characteristic curves for the CR, PSNR, and HDR-VDP were 0.87, 0.93, and 0.97, respectively, showing significant differences between the CR and PSNR (p=0.04), or HDR-VDP (p<0.001), and between the PSNR and HDR-VDP (p<0.001). In conclusion, the CR is less suitable than the PSNR or HDR-VDP as an objective index of image fidelity for JPEG2000 compressed body CT images. The HDR-VDP is more promising than the PSNR as such an index.

  8. Regarding Autocontouring and Manual Contouring: Which Is the Better Method for Target Delineation Using 18F-FDG PET/CT in NonSmall Cell Lung Cancer? By K. Wu et al

    E-Print Network [OSTI]

    Boyer, Edmond

    Using 18F-FDG PET/CT in Non­Small Cell Lung Cancer? By K. Wu et al M Hatt, D Visvikis, C Cheze Le Rest delineation in PET/CT for NSCLC. 17 NSCLC tumors were delineated with both automated and manual approaches, using either combined PET/CT or CT and PET independently. As expected, the manual contouring of the PET

  9. Contract No. DE-AC02-07CH11358 Contract Modification No. 0145

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    H-11 H.8 PRIVACY ACT RECORDS H-12 H.9 ADDITIONAL DEFINITIONS H-12 H.10 SERVICE CONTRACT ACT OF 1965 (41 U.S.C. 35) H-14 Contract No. DE-AC02-07CH11358 Section H TOC...

  10. An empirical study of the economies of scale in AC transmission line construction costs

    E-Print Network [OSTI]

    Baldick, Ross

    1 An empirical study of the economies of scale in AC transmission line construction costs Krishnan data filed at the Federal Energy Regulatory Commission to empirically determine the cost of transmission projects completed between the years 1994 and 2000. We examine the economies of scale in the cost

  11. Techniques for energy conservation in ac motor-driven systems. Final report

    SciTech Connect (OSTI)

    Mohan, N.

    1981-09-01T23:59:59.000Z

    Techniques for energy conservation of reducing losses in ac motor-driven systems proposed by the technical community in response to surging cost of energy are evaluated and compared. Report objectives are to provide better understanding of underlying principles and to evaluate technical and economic viability of these techniques for various applications. An important aspect considered is the impact on electric utility system in terms of harmonics, power factor of operation, and Electro-Magnetic Interference (EMI). The techniques evaluated are: NASA Power Factor Controller, a simple device for reducing power losses in lightly loaded ac motors; wanlass motor modification, a scheme of reconnecting motor windings with capacitors in series, with the intention of improving the motor efficiencies under all loading conditions; conventional variable frequency solid-state inverters which can control the speed of ac motors by producing adjustable frequency ac voltage, with a significant potential for energy conservation in pumps and air-handling systems; and other variable frequency drives and schemes including cycloconverters, slip-recovery scheme, Exxon Alternating Current Synthesizer, Venturini conversion technique, permanent magnet synchronous motors, and a device called the Phase-Liner. The impact of rapid growth in semiconductors and magnetic materials technologies is also considered.

  12. Integrated Research Center http://www.kobe-u.ac.jp/kuirc/index.html

    E-Print Network [OSTI]

    Banbara, Mutsunori

    . Integrated Bio-refinery Research Project [ Project Leader: KONDO Akihiko ] Research Project for MembraneIntegrated Research Center http://www.kobe-u.ac.jp/kuirc/index.html In fiscal year 2013, the organization of the Integrated Research Center was changed into an interdisciplinary education and research

  13. http://www.ukro.ac.uk FP7 in 2013 making the most of the

    E-Print Network [OSTI]

    Royal Holloway, University of London

    , University of London 6 November 2012 Inga Benner inga.benner@bbsrc.ac.uk #12;UK Research Office · Based someone to speak to in the European Commission · Project management issues, reporting, audit · Wider (ICT) Nanosciences, Nanotechnologies, Materials and new Production Technologies (NMP) Energy

  14. Operation-Based Signal-Flow AC Analysis of Switching DCDC Converters in CCM and DCM

    E-Print Network [OSTI]

    Rincon-Mora, Gabriel A.

    Operation-Based Signal-Flow AC Analysis of Switching DC­DC Converters in CCM and DCM Dongwon Kwon (CCM and DCM) and insightful enough to derive directly from the waveforms of the circuit, not from- and discontinuous-conduction modes (CCM and DCM). To this end, for review, Sections II and III of the paper overview

  15. Non-Linear Continuum Regression Using Genetic Programming Ben.McKay@ncl.ac.uk

    E-Print Network [OSTI]

    Fernandez, Thomas

    Non-Linear Continuum Regression Using Genetic Programming Ben McKay Ben.McKay@ncl.ac.uk Mark Willis In this contribution, genetic programming is combined with continuum regression to produce two novel non-linear-based' strategy. Having discussed continuum regression, the modifications required to extend the algorithm for non-linear

  16. AC 2007-2003: UNDERWATER LEGO ROBOTICS: TESTING, EVALUATION & Adam Carberry, Tufts University

    E-Print Network [OSTI]

    AC 2007-2003: UNDERWATER LEGO ROBOTICS: TESTING, EVALUATION & REDESIGN Adam Carberry, Tufts from Tufts. He is also a research assistant at the Tufts University Center for Engineering Educational a difference in bringing engineering to K-12 education. He is also a research assistant at the Tufts University

  17. Modification No.0136 Contract No. DE-AC02-09CH11466

    E-Print Network [OSTI]

    Princeton Plasma Physics Laboratory

    of the Princeton Plasma Physics Laboratory A Department of Energy National Laboratory Contract No. DE-AC02-09CH.2 Provide Effective and Efficient Science and Technology Project / Program / Facilities Management J-B-28 3 Financial Management System(s) J-B-42 6.2 Provide and Efficient, Effective, and Responsive Acquisition

  18. Microprocessor-based random PWM schemes for DC-AC power conversion

    SciTech Connect (OSTI)

    Hui, S.Y.R. [Univ. of Sydney, New South Wales (Australia). Dept. of Electrical Engineering] [Univ. of Sydney, New South Wales (Australia). Dept. of Electrical Engineering; [City Univ. of Hong Kong, Kowloon (Hong Kong). Dept. of Electronic Engineering; Oppermann, I.; Sathiakumar, S. [Univ. of Sydney, New South Wales (Australia). Dept. of Electrical Engineering] [Univ. of Sydney, New South Wales (Australia). Dept. of Electrical Engineering

    1997-03-01T23:59:59.000Z

    Two classes of microprocessor-based random PWM (RPWM) real-time schemes for dc-ac power conversion are compared and evaluated. Performance of the RPWM schemes based on the mathematical and logical approaches is examined. The proposed schemes exhibit excellent harmonic content with all low and high-order harmonics suppressed and are suitable for both MOSFET and IGBT inverters.

  19. Contract Number: DE-AC05-76RL01830 Modification M971

    E-Print Network [OSTI]

    that in consideration of the extension of Contract No. DE- AC05-76RL01830 (hereinafter referred to as "the PNNL Prime, Appendix H of the PNNL Prime Contract (hereinafter referred to as "the Facilities") and the right include any use authorized under the PNNL Prime Contract, or as otherwise agreed to by the Parties. 2

  20. DE-AC02-76SF00515 Contractor Performance Evaluation and

    E-Print Network [OSTI]

    Wechsler, Risa H.

    #12;#12;DE-AC02-76SF00515 Appendix B M544 FY 2008 Contractor Performance Evaluation and Measurement Plan for Management and Operations ofthe Stanford Linear Accelerator Center 10-03-07 09:58 RCVD J