Sample records for oxygenates supply curves

  1. Crude oil supply curves

    E-Print Network [OSTI]

    Adelman, Morris Albert

    1998-01-01T23:59:59.000Z

    Short-run cost curves shift over time as depletion counters increasing knowledge. Under competition, a rightward (leftward) shift indicates lower (higher) cost and greater (lesser) productivity. A simple coefficient captures ...

  2. Updated U.S. Geothermal Supply Curve

    SciTech Connect (OSTI)

    Augustine, C.; Young, K. R.; Anderson, A.

    2010-02-01T23:59:59.000Z

    This paper documents the approach used to update the U.S. geothermal supply curve. The analysis undertaken in this study estimates the supply of electricity generation potential from geothermal resources in the United States and the levelized cost of electricity (LCOE), capital costs, and operating and maintenance costs associated with developing these geothermal resources. Supply curves were developed for four categories of geothermal resources: identified hydrothermal (6.4 GWe), undiscovered hydrothermal (30.0 GWe), near-hydrothermal field enhanced geothermal systems (EGS) (7.0 GWe) and deep EGS (15,900 GWe). Two cases were considered: a base case and a target case. Supply curves were generated for each of the four geothermal resource categories for both cases. For both cases, hydrothermal resources dominate the lower cost range of the combined geothermal supply curve. The supply curves indicate that the reservoir performance improvements assumed in the target case could significantly lower EGS costs and greatly increase EGS deployment over the base case.

  3. THE ECONOMICS OF CONSERVED-ENERGY "SUPPLY" CURVES

    E-Print Network [OSTI]

    California at Berkeley. University of

    is part of the working papers series of the Program on Workable Energy Regulation (POWER). POWERPWP-028 THE ECONOMICS OF CONSERVED-ENERGY "SUPPLY" CURVES Steven Stoft April 1995 This paper is a program of the University of California Energy Institute, a multicampus research unit of the University

  4. Enhanced carbon-oxygen log interpretations using supplemental log curves

    SciTech Connect (OSTI)

    Wyatt, D.F. Jr.; Jacobson, L.A.; Fox, P.

    1994-12-31T23:59:59.000Z

    Supplemental measurements from induced nuclear spectrometry tools are examined to demonstrate what additional information they provide about the well and reservoir conditions. Logs in shut-in wells from Indonesia provide examples of oxygen activation measurements showing cross-flow from one reservoir to another via open perforations. Leaking squeezed perforations were also observed. An example from Alaska shows radioactive scale build-up in the casing which spectral analysis identifies as a mixture of uranium and thorium salts. Another log, where the casing fluid was replaced with crude oil, demonstrates a technique for identifying cement channels. Logs from Nigeria comparing oil saturation estimates before and after a squeeze operation illustrate the effect of casing fluid flushing of the formation through open perforations. Understanding the diagnostic character of these curves leads to higher confidence in the overall log interpretation process.

  5. Mineralization pathways in lake sediments with different oxygen and organic carbon supply

    E-Print Network [OSTI]

    Wehrli, Bernhard

    Mineralization pathways in lake sediments with different oxygen and organic carbon supply Martin Abstract The intensity and pathways of mineralization of sedimentary organic matter were investigated equipped with both oxygen and ion-selective electrodes. Anaerobic sedimentary mineralization ranged from 13

  6. Supply curve impacts of Quick Start projects in Phase 1 of the Resource Supply Expansion Program

    SciTech Connect (OSTI)

    Wright, G.A.; Warwick, W.M.; Durfee, D.L.

    1993-12-01T23:59:59.000Z

    The Pacific Northwest Laboratory (PNL) prepared this report under contract to the Bonneville Power Administration (Bonneville), as part of the Resource Supply Expansion Project (RSEP). RSEP is a regional program instituted by Bonneville to expand conservation and renewable generation options available to resource planners and utilities. Resource alternatives are increased by RSEP through demonstration projects designed in a collaborative process that targets specific barriers to resource development including institutional, market, and reliability barriers. RSEP was launched with several projects that were designed and implemented quickly in 1992 to lay a foundation for future collaboration. The purpose of this report is to introduce the goal and structure of RSEP and to describe the so-called ``Quick Start`` RSEP projects in Phase One of RSEP. This description includes a preliminary estimate of the energy savings and/or other expected impacts of RSEP projects funded in FY 1992 and 1993. Similar estimates are also included for Bonneville projects to confirm wind and geothermal generation potential. Bonneville`s Geothermal Confirmation Agenda preceded implementation of RSEP, although it has a similar objective and collaborative approach.

  7. Gas Composition and Oxygen Supply in the Root Environment of Substrates in Closed Hydroponic Systems

    E-Print Network [OSTI]

    Lieth, J. Heinrich

    299 Gas Composition and Oxygen Supply in the Root Environment of Substrates in Closed Hydroponic Abstract The objective of this study was to get more information about the root zone, mainly the gas and ethylene, a gas sampling system was used to get gas samples from the root zone. CO2 gas samples of 20 ml

  8. Oxygenate Supply/Demand Balances in the Short-Term Integrated Forecasting Model (Released in the STEO March 1998)

    Reports and Publications (EIA)

    1998-01-01T23:59:59.000Z

    The blending of oxygenates, such as fuel ethanol and methyl tertiary butyl ether (MTBE), into motor gasoline has increased dramatically in the last few years because of the oxygenated and reformulated gasoline programs. Because of the significant role oxygenates now have in petroleum product markets, the Short-Term Integrated Forecasting System (STIFS) was revised to include supply and demand balances for fuel ethanol and MTBE. The STIFS model is used for producing forecasts in the Short-Term Energy Outlook. A review of the historical data sources and forecasting methodology for oxygenate production, imports, inventories, and demand is presented in this report.

  9. Wind Supply Curves and Location Scenarios in the West: Summary of the Clean and Diverse Energy Wind Task Force Report; Preprint

    SciTech Connect (OSTI)

    Milligan, M.; Parsons, B.; Shimshak, R.; Larson, D.; Carr, T.

    2006-06-01T23:59:59.000Z

    This paper presents supply curves and scenarios that were developed by the Wind Task Force. Much of this information has been adapted from the original Wind Task Force report.

  10. Interplay of oxygen-evolution kinetics and photovoltaic power curves on the construction of artificial leaves

    E-Print Network [OSTI]

    Surendranath, Yogesh

    An artificial leaf can perform direct solar-to-fuels conversion. The construction of an efficient artificial leaf or other photovoltaic (PV)-photoelectrochemical device requires that the power curve of the PV material and ...

  11. Real space mapping of oxygen vacancy diffusion and electrochemical transformations by hysteretic current reversal curve measurements

    SciTech Connect (OSTI)

    Kalinin, Sergei V.; Balke, Nina; Borisevich, Albina Y.; Jesse, Stephen; Maksymovych, Petro; Kim, Yunseok; Strelcov, Evgheni

    2014-06-10T23:59:59.000Z

    An excitation voltage biases an ionic conducting material sample over a nanoscale grid. The bias sweeps a modulated voltage with increasing maximal amplitudes. A current response is measured at grid locations. Current response reversal curves are mapped over maximal amplitudes of the bias cycles. Reversal curves are averaged over the grid for each bias cycle and mapped over maximal bias amplitudes for each bias cycle. Average reversal curve areas are mapped over maximal amplitudes of the bias cycles. Thresholds are determined for onset and ending of electrochemical activity. A predetermined number of bias sweeps may vary in frequency where each sweep has a constant number of cycles and reversal response curves may indicate ionic diffusion kinetics.

  12. Simulation of Polarization Curves for Oxygen Reduction Reaction in 0.5 M H2SO4 at a Rotating Ring Disk Electrode

    E-Print Network [OSTI]

    fuel cell PEMFC can cause the failure of the membrane.1-3 Peroxide can be generated in the oxygenSimulation of Polarization Curves for Oxygen Reduction Reaction in 0.5 M H2SO4 at a Rotating Ring is used to simulate the oxygen reduction reaction in 0.5 M H2SO4 at a rotating ring disk electrode

  13. Development of a Novel Oxygen Supply Process and its Integration with an Oxy-Fuel Coal-Fired Boiler

    SciTech Connect (OSTI)

    None

    2006-12-31T23:59:59.000Z

    BOC, the world's second largest industrial gas company, has developed a novel high temperature sorption based technology referred to as CAR (Cyclic Autothermal Recovery) for oxygen production and supply to oxy-fuel boilers with flue gas recycle. This technology is based on sorption and storage of oxygen in a fixed bed containing mixed ionic and electronic conductor materials. The objective of the proposed work was to construct a CAR PDU that was capable of producing 10-scfm of oxygen, using steam or recycled flue gas as the sweep gas, and install it in the Combustion Test Facility. The unit was designed and fabricated at BOC/The Linde Group, Murray Hill, New Jersey. The unit was then shipped to WRI where the site had been prepared for the unit by installation of air, carbon dioxide, natural gas, nitrogen, computer, electrical and infrastructure systems. Initial experiments with the PDU consisted of flowing air into both sides of the absorption systems and using the air heaters to ramp up the bed temperatures. The two beds were tested individually to operational temperatures up to 900 C in air. The cycling process was tested where gases are flowed alternatively from the top then bottom of the beds. The PDU unit behaved properly with respect to flow, pressure and heat during tests. The PDU was advanced to the point where oxygen production testing could begin and integration to the combustion test facility could occur.

  14. Critical role for mesoscale eddy diffusion in supplying oxygen to hypoxic ocean waters1 Anand Gnanadesikan*3

    E-Print Network [OSTI]

    Gnanadesikan, Anand

    by the current generation of Earth System Models. Using satellite-based22 estimate of oxygen consumption 1000 m2 /s. Varying Aredi across a suite24 of Earth System Models yields a broadly consistent result with about 1/3 of these waters39 dropping below 10 M (solid black line, Fig. 1c,d).40 The Earth System Models

  15. Variability in Proto-Planetary Nebulae: IV. Light Curve Analyses of Four Oxygen-Rich, F Spectral-Type Objects

    E-Print Network [OSTI]

    Hrivnak, Bruce J; Nault, Kristie A

    2015-01-01T23:59:59.000Z

    We present new light curves covering 14 to 19 years of observations of four bright proto-planetary nebulae (PPNs), all O-rich and of F spectral type. They each display cyclical light curves with significant variations in amplitude. All four were previously known to vary in light. Our data were combined with published data and searched for periodicity. The results are as follows: IRAS 19475+3119 (HD 331319; 41.0 days), 17436+5003 (HD 161796; 45.2 days), 19386+0155 (101.8 days), and 18095+2704 (113.3 days). The two longer periods are in agreement with previous studies while the two shorter periods each reveal for the first time reveal a dominant period over these long observing intervals. Multiple periods were also found for each object. The secondary periods were all close to the dominant periods, with P2/P1 ranging from 0.86 to 1.06. The variations in color reveal maximum variations in T(eff) of 400 to 770 K. These variations are due to pulsations in these post-AGB objects. Maximum seasonal light variations a...

  16. Pilot-Scale Demonstration of a Novel, Low-Cost Oxygen Supply Process and its Integration with Oxy-Fuel Coal-Fired Boilers

    SciTech Connect (OSTI)

    Krish Krishnamurthy; Divy Acharya; Frank Fitch

    2008-09-30T23:59:59.000Z

    In order to achieve DOE targets for carbon dioxide capture, it is crucial not only to develop process options that will generate and provide oxygen to the power cycle in a cost-effective manner compared to the conventional oxygen supply methods based on cryogenic air separation technology, but also to identify effective integration options for these new technologies into the power cycle with carbon dioxide capture. The Linde/BOC developed Ceramic Autothermal Recovery (CAR) process remains an interesting candidate to address both of these issues by the transfer of oxygen from the air to a recycled CO{sub 2} rich flue-gas stream in a cyclic process utilizing the high temperature sorption properties of perovskites. Good progress was made on this technology in this project, but significant challenges remain to be addressed before CAR oxygen production technology is ready for commercial exploitation. Phase 1 of the project was completed by the end of September 2008. The two-bed 0.7 tons/day O2 CAR process development unit (PDU) was installed adjacent to WRI's pilot scale coal combustion test facility (CTF). Start-up and operating sequences for the PDU were developed and cyclic operation of the CAR process demonstrated. Controlled low concentration methane addition allowed the beds to be heated up to operational temperature (800-900 C) and then held there during cyclic operation of the 2-bed CAR process, in this way overcoming unavoidable heat losses from the beds during steady state operation. The performance of the PDU was optimized as much as possible, but equipment limitations prevented the system from fully achieving its target performance. Design of the flue gas recirculation system to integrate CAR PDU with the CTF and the system was completed and integrated tests successfully performed at the end of the period. A detailed techno-economic analysis was made of the CAR process for supplying the oxygen in oxy-fuel combustion retrofit option using AEP's 450 MW Conesville, Ohio plant and contrasted with the cryogenic air separation option (ASU). Design of a large scale CAR unit was completed to support this techno-economic assessment. Based on the finding that the overall cost potential of the CAR technology compared to cryogenic ASU is nominal at current performance levels and that the risks related to both material and process scale up are still significant, the team recommended not to proceed to Phase 2. CAR process economics continue to look attractive if the original and still 'realistic' target oxygen capacities could be realized in practice. In order to achieve this end, a new fundamental materials development program would be needed. With the effective oxygen capacities of the current CAR materials there is, however, insufficient economic incentive to use this commercially unproven technology in oxy-fuel power plant applications in place of conventional ASUs. In addition, it is now clear that before a larger scale pilot demonstration of the CAR technology is made, a better understanding of the impact of flue-gas impurities on the CAR materials and of thermal transients in the beds is required.

  17. The Present, Mid-Term, and Long-Term Supply Curves for Tellurium; and Updates in the Results from NREL's CdTe PV Module Manufacturing Cost Model (Presentation)

    SciTech Connect (OSTI)

    Woodhouse, M.; Goodrich, A.; Redlinger, M.; Lokanc, M.; Eggert, R.

    2013-09-01T23:59:59.000Z

    For those PV technologies that rely upon Te, In, and Ga, first-order observations and calculations hint that there may be resource constraints that could inhibit their successful deployment at a SunShot level. These are only first-order approximations, however, and the possibility for an expansion in global Te, In, and Ga supplies needs to be considered in the event that there are upward revisions in their demand and prices.In this study, we examine the current, mid-term, and long-term prospects of Tellurium (Te) for use in PV. We find that the current global supply base of Te would support <10 GW of annual traditional CdTe PV manufacturing production. But as for the possibility that the supply base for Te might be expanded, after compiling several preliminary cumulative availability curves we find that there may be significant upside potential in the supply base for this element - principally vis a vis increasing demand and higher prices. Primarily by reducing the Tellurium intensity in manufacturing and by increasing the recovery efficiency of Te in Cu refining processes, we calculate that it may prove affordable to PV manufacturers to expand the supply base for Te such that 100 GW, or greater, of annual CdTe PV production is possible in the 2030 - 2050 timeframe.

  18. Oxygenate Supply/Demand Balances

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122 40 Buildingto17 3400,Information55,035OAK GROVE C OAL D EGASPresented to the

  19. Conservation Screening Curves to Compare Efficiency Investments to Power Plants

    E-Print Network [OSTI]

    methodology to compare supply and demand-side resources. The screening curve approach supplements with load curve approach supplements with load shape information the data contained in a supply curve of conservedLBL-27286 Conservation Screening Curves to Compare Efficiency Investments to Power Plants Jonathan

  20. The Role of Oxygen in Coal Gasification 

    E-Print Network [OSTI]

    Klosek, J.; Smith, A. R.; Solomon, J.

    1986-01-01T23:59:59.000Z

    Air Products supplies oxygen to a number of coal gasification and partial oxidation facilities worldwide. At the high operating pressures of these processes, economics favor the use of 90% and higher oxygen purities. The effect of inerts...

  1. Blood oxygen transport and depletion : the key of consummate divers

    E-Print Network [OSTI]

    Meir, Jessica Ulrika

    2009-01-01T23:59:59.000Z

    and Dill, D. B. (1935). Oxygen dissociation curves of birdE. (1964). A venous blood oxygen reservoir in the divingand Torrance, J. D. (1977). Oxygen-Affinity of Avian Blood.

  2. Learning Curve

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1997-03-28T23:59:59.000Z

    It is a fundamental human characteristic that a person engaged in a repetitive task will improve his performance over time. If data are gathered on this phenomenon, a curve representing a decrease in effort per unit for repetitive operations can be developed. This phenomenon is real and has a specific application in cost analysis, cost estimating, or profitability studies related to the examination of future costs and confidence levels in an analysis. This chapter discusses the development and application of the learning curve.

  3. Oxygen analyzer

    DOE Patents [OSTI]

    Benner, William H. (Danville, CA)

    1986-01-01T23:59:59.000Z

    An oxygen analyzer which identifies and classifies microgram quantities of oxygen in ambient particulate matter and for quantitating organic oxygen in solvent extracts of ambient particulate matter. A sample is pyrolyzed in oxygen-free nitrogen gas (N.sub.2), and the resulting oxygen quantitatively converted to carbon monoxide (CO) by contact with hot granular carbon (C). Two analysis modes are made possible: (1) rapid determination of total pyrolyzable oxygen obtained by decomposing the sample at 1135.degree. C., or (2) temperature-programmed oxygen thermal analysis obtained by heating the sample from room temperature to 1135.degree. C. as a function of time. The analyzer basically comprises a pyrolysis tube containing a bed of granular carbon under N.sub.2, ovens used to heat the carbon and/or decompose the sample, and a non-dispersive infrared CO detector coupled to a mini-computer to quantitate oxygen in the decomposition products and control oven heating.

  4. Flow Duration Curve Load Duration Curve

    E-Print Network [OSTI]

    #12;Flow Duration Curve Load Duration Curve #12;1. Develop Flow Duration Curve 2. Estimate load given flow and concentration data--select appropriate conversion factors 3. Develop Load Duration Curve 4. Plot observed data with Load Duration Curve #12;What are they? How do you make one? #12;Describes

  5. Flow Duration Curve Load Duration Curve

    E-Print Network [OSTI]

    Flow Duration Curve Load Duration Curve 1. Develop Flow Duration Curve 2. Estimate load given flow and concentration data--select appropriate conversion factors 3. Develop Load Duration Curve 4. Plot observed data with Load Duration Curve What are they? How do you make one? Describes the percent of time a flow rate

  6. Curved Space or Curved Vacuum?

    E-Print Network [OSTI]

    Eric V. Linder

    2005-10-11T23:59:59.000Z

    While the simple picture of a spatially flat, matter plus cosmological constant universe fits current observation of the accelerated expansion, strong consideration has also been given to models with dynamical vacuum energy. We examine the tradeoff of ``curving'' the vacuum but retaining spatial flatness, vs. curving space but retaining the cosmological constant. These different breakdowns in the simple picture could readily be distinguished by combined high accuracy supernovae and cosmic microwave background distance measurements. If we allow the uneasy situation of both breakdowns, the curvature can still be measured to 1%, but at the price of degrading estimation of the equation of state time variation by 60% or more, unless additional information (such as weak lensing data or a tight matter density prior) is included.

  7. Instrumental Variables and the Search for Identification: From Supply and

    E-Print Network [OSTI]

    Ahmad, Sajjad

    of the elasticities of supply and demand from the relationship between price and quantity 1 See Goldberger (1972 and supply curves shift over time, the observed data on quantities and prices reflect a set of equilibrium points on both curves. Consequently, an ordinary least squares regression of quantities on prices fails

  8. Oxygen analyzer

    DOE Patents [OSTI]

    Benner, W.H.

    1984-05-08T23:59:59.000Z

    An oxygen analyzer which identifies and classifies microgram quantities of oxygen in ambient particulate matter and for quantitating organic oxygen in solvent extracts of ambient particulate matter. A sample is pyrolyzed in oxygen-free nitrogen gas (N/sub 2/), and the resulting oxygen quantitatively converted to carbon monoxide (CO) by contact with hot granular carbon (C). Two analysis modes are made possible: (1) rapid determination of total pyrolyzable obtained by decomposing the sample at 1135/sup 0/C, or (2) temperature-programmed oxygen thermal analysis obtained by heating the sample from room temperature to 1135/sup 0/C as a function of time. The analyzer basically comprises a pyrolysis tube containing a bed of granular carbon under N/sub 2/, ovens used to heat the carbon and/or decompose the sample, and a non-dispersive infrared CO detector coupled to a mini-computer to quantitate oxygen in the decomposition products and control oven heating.

  9. Dissolved Oxygen in Allen CreekDissolved Oxygen in Allen Creek Dissolved oxygen (DO) enters the water by diffusion from air, as a by-product of photosynthesis and

    E-Print Network [OSTI]

    Tyler, Christy

    Dissolved Oxygen in Allen CreekDissolved Oxygen in Allen Creek Dissolved oxygen (DO) enters and rapids. There is an inverse relationship between temperature and DO, i.e. colder water holds more oxygen it supplies oxygen to aquatic organisms. Higher DO levels also give the water a better taste. Figure 2. During

  10. Every curve is a Teichmuller curve

    E-Print Network [OSTI]

    Ellenberg, Jordan S

    2009-01-01T23:59:59.000Z

    We prove that every algebraic curve X defined over the algebraic closure of the rationals is birational over the complex numbers to a Teichmuller curve.

  11. Why Supply Chain

    E-Print Network [OSTI]

    Datta, Shoumen

    2000-01-01T23:59:59.000Z

    Why supply chain explains the importance of supply chains. It includes an introduction to ERP as designed by SAP.

  12. Petroleum supply annual 1993. Volume 1

    SciTech Connect (OSTI)

    Not Available

    1994-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1993 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1993, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Below is a description of each section in Volume 1 of the PSA.

  13. Petroleum supply annual 1994. Volume 1

    SciTech Connect (OSTI)

    NONE

    1995-05-22T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1994 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1994, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Below is a description of each section in Volume 1 of the PSA.

  14. 1992 Conversion Resources Supply Document

    SciTech Connect (OSTI)

    Not Available

    1992-03-01T23:59:59.000Z

    In recent years conservation of electric power has become an integral part of utility planning. The 1980 Pacific Northwest Electric Power Planning and Conservation Act (Northwest Power Act) requires that the region consider conservation potential in planning acquisitions of resources to meet load growth. The Bonneville Power Administration (BPA) developed its first estimates of conservation potential in 1982. Since that time BPA has updated its conservation supply analyses as a part of its Resource Program and other planning efforts. Major updates were published in 1985 and in January 1990. This 1992 document presents updated supply curves, which are estimates of the savings potential over time (cumulative savings) at different cost levels of energy conservation measures (ECMs). ECMs are devices, pieces of equipment, or actions that increase the efficiency of electricity use and reduce the amount of electricity used by end-use equipment.

  15. Petroleum supply monthly, with data from June 1996

    SciTech Connect (OSTI)

    NONE

    1996-08-01T23:59:59.000Z

    The Petroleum Supply Division (PSD) of the Energy Information Administration (EIA) collects and published information on petroleum supply and disposition in the United States. The information is collected through a series of surveys that make up the Petroleum Supply Reporting System (PSRS). The PSRS data are published in the Weekly Petroleum Status Report (WPSR), Petroleum Supply Monthly (PSM), and Petroleum Supply Annual (PSA). This report presents information on crude oil production, crude oil imports and exports, refinery operations, natural gas processing, transportation, and oxygenate data.

  16. 2009 Geothermal, Co-Production, and GSHP Supply Curves

    Broader source: Energy.gov (indexed) [DOE]

    and Description Hydrothermal Identified Hydrothermal Sites 6.39 USGS 2008 Geothermal Resource Assessment 1 - Identified hydrothermal sites - Sites 110 o C included -...

  17. Cost Curves for Gas Supply Security: The Case of Bulgaria

    E-Print Network [OSTI]

    Silve, Florent; Noël, Pierre

    . Interconnections: 8.64 7.92 14 - 5 Figure 2. Structure of gas consumption by sector, Bulgaria (2007) Figure 3. Structure of heat generation by fuel type, Bulgaria (2007) Figure 4. Electricity generation mix, Bulgaria (2007) Chemical industry 31... to put the vertical dotted line). The government may want to insure the gas consumption of some specific categories of customers, the interruption of which Cost per unit of peak gas consumption insured (m€/mcm/day) Cumulative level of peak gas...

  18. Selected GHG Emission Supply Curves | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty Edit with form HistoryRistma AG Jump638324°,Schnell ZTools andSegen LtdGHG Emission

  19. McKinsey Carbon Supply Curves | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere I Geothermal Pwer Plant JumpMarysville, Ohio: Energy ResourcesMaviMcCullochMcGregor,McKayMcKinleyville,Carbon

  20. Motor Systems Efficiency Supply Curves | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere I Geothermal Pwer Plant JumpMarysville,Missoula,MontereyHill, California:Morse, Louisiana:Mosinee,MossMotor

  1. active oxygen control: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the oxygen sensor has limitation because it provides a fixed point on the sensible heat loss curve. A better way is to measure the fuel... Miller, J. G. 2 Short...

  2. Compressed Air Supply Efficiency 

    E-Print Network [OSTI]

    Joseph, B.

    2004-01-01T23:59:59.000Z

    COMPRESSED AIR SUPPLY EFFICENCY Babu Joseph, Ph.D., P.E. Engineer Southern California Edison Irwindale, CA ABSTRACT This project, under contract from California Energy Commission, developed the CASE (Compressed Air Supply Efficiency...

  3. Pairings on hyperelliptic curves

    E-Print Network [OSTI]

    Balakrishnan, Jennifer; Chisholm, Sarah; Eisentraeger, Kirsten; Stange, Katherine; Teske, Edlyn

    2009-01-01T23:59:59.000Z

    We assemble and reorganize the recent work in the area of hyperelliptic pairings: We survey the research on constructing hyperelliptic curves suitable for pairing-based cryptography. We also showcase the hyperelliptic pairings proposed to date, and develop a unifying framework. We discuss the techniques used to optimize the pairing computation on hyperelliptic curves, and present many directions for further research.

  4. Petroleum supply annual 1994, Volume 2

    SciTech Connect (OSTI)

    NONE

    1995-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1994 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1994, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary.

  5. Simultaneous confidence bands in curve prediction applied to load curves

    E-Print Network [OSTI]

    Boyer, Edmond

    Simultaneous confidence bands in curve prediction applied to load curves J.M. Aza¨is1, S. Bercu2, J, load curve. 1 Introduction In curve prediction, one is generally interested in deriving simultaneous this technique in the numerical context of load curve pre- diction: power producers like EDF, the electrical

  6. Petroleum Supply Monthly

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    adjustments, minus stock change, minus refinery and blender net inputs, minus exports. Net receipts are added as a component of supply at the PAD District level. Crude oil...

  7. OXYGEN ENHANCED COMBUSTION FOR NOx CONTROL

    SciTech Connect (OSTI)

    David R. Thompson; Lawrence E. Bool; Jack C. Chen

    2003-08-01T23:59:59.000Z

    This quarterly technical progress report will summarize work accomplished for the Program through the thirteenth quarter, April-June 2003, in the following task areas: Task 1--Oxygen Enhanced Combustion, Task 3--Economic Evaluation and Task 4--Program Management. The program is proceeding in accordance with project objectives. REI's model was modified to evaluate mixing issues in the upper furnace of a staged unit. Analysis of the results, and their potential application to this unit is ongoing. Economic evaluation continues to confirm the advantage of oxygen-enhanced combustion. A contract for a commercial demonstration has been signed with the Northeast Generation Services Company to supply oxygen and license the oxygen enhanced low NOx combustor technology for use at the 147-megawatt coal fired Mt. Tom Station in Holyoke, MA. Commercial proposals have been submitted. Economic analysis of a beta site test performance was conducted.

  8. Updated U.S. Geothermal Supply Characterization and Representation for Market Penetration Model Input

    SciTech Connect (OSTI)

    Augustine, C.

    2011-10-01T23:59:59.000Z

    The U.S. Department of Energy (DOE) Geothermal Technologies Program (GTP) tasked the National Renewable Energy Laboratory (NREL) with conducting the annual geothermal supply curve update. This report documents the approach taken to identify geothermal resources, determine the electrical producing potential of these resources, and estimate the levelized cost of electricity (LCOE), capital costs, and operating and maintenance costs from these geothermal resources at present and future timeframes under various GTP funding levels. Finally, this report discusses the resulting supply curve representation and how improvements can be made to future supply curve updates.

  9. Artificial oxygen transport protein

    DOE Patents [OSTI]

    Dutton, P. Leslie

    2014-09-30T23:59:59.000Z

    This invention provides heme-containing peptides capable of binding molecular oxygen at room temperature. These compounds may be useful in the absorption of molecular oxygen from molecular oxygen-containing atmospheres. Also included in the invention are methods for treating an oxygen transport deficiency in a mammal.

  10. Covalency in Metal-Oxygen Multiple Bonds Evaluated Using Oxygen...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Multiple Bonds Evaluated Using Oxygen K-edge Spectroscopy and Electronic Structure Theory . Covalency in Metal-Oxygen Multiple Bonds Evaluated Using Oxygen K-edge Spectroscopy...

  11. Improving supply chain resilience

    E-Print Network [OSTI]

    Leung, Elsa Hiu Man

    2009-01-01T23:59:59.000Z

    Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

  12. Compressed Air Supply Efficiency

    E-Print Network [OSTI]

    Joseph, B.

    2004-01-01T23:59:59.000Z

    This project, under contract from California Energy Commission, developed the CASE (Compressed Air Supply Efficiency) Index as a stand-alone value for compressor central plant efficiency. This Index captures the overall efficiency of a compressed...

  13. Supply chain dynamics

    E-Print Network [OSTI]

    Barbosa, Ricardo Wagner Lopes, 1976-

    2003-01-01T23:59:59.000Z

    The strong bargaining power of major retailers and the higher requirements for speed, service excellence and customization have significantly contributed to transform the Supply Chain Management. These increasing challenges ...

  14. European supply chain study

    E-Print Network [OSTI]

    Puri, Mohitkumar

    2009-01-01T23:59:59.000Z

    Introduction: Supply chain management has been defined as, "..a set of approaches utilized to efficiently integrate suppliers, manufacturers, warehouses and stores, so that merchandise is produced and distributed at the ...

  15. oxygen-plasma | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    oxygen-plasma oxygen-plasma Leads No leads are available at this time. Conversion of 1,2-Propylene Glycol on Rutile TiO2(110). Abstract: We have studied the reactions of...

  16. Oxygen enriched combustion system performance study. Phase 2: 100 percent oxygen enriched combustion in regenerative glass melters, Final report

    SciTech Connect (OSTI)

    Tuson, G.B.; Kobayashi, H.; Campbell, M.J.

    1994-08-01T23:59:59.000Z

    The field test project described in this report was conducted to evaluate the energy and environmental performance of 100% oxygen enriched combustion (100% OEC) in regenerative glass melters. Additional objectives were to determine other impacts of 100% OEC on melter operation and glass quality, and to verify on a commercial scale that an on-site Pressure Swing Adsorption oxygen plant can reliably supply oxygen for glass melting with low electrical power consumption. The tests constituted Phase 2 of a cooperative project between the United States Department of Energy, and Praxair, Inc. Phase 1 of the project involved market and technical feasibility assessments of oxygen enriched combustion for a range of high temperature industrial heating applications. An assessment of oxygen supply options for these applications was also performed during Phase 1, which included performance evaluation of a pilot scale 1 ton per day PSA oxygen plant. Two regenerative container glass melters were converted to 100% OEC operation and served as host sites for Phase 2. A 75 ton per day end-fired melter at Carr-Lowrey Glass Company in Baltimore, Maryland, was temporarily converted to 100% OEC in mid- 1990. A 350 tpd cross-fired melter at Gallo Glass Company in Modesto, California was rebuilt for permanent commercial operation with 100% OEC in mid-1991. Initially, both of these melters were supplied with oxygen from liquid storage. Subsequently, in late 1992, a Pressure Swing Adsorption oxygen plant was installed at Gallo to supply oxygen for 100% OEC glass melting. The particular PSA plant design used at Gallo achieves maximum efficiency by cycling the adsorbent beds between pressurized and evacuated states, and is therefore referred to as a Vacuum/Pressure Swing Adsorption (VPSA) plant.

  17. Heat release analysis of oxygen-enriched diesel combustion

    SciTech Connect (OSTI)

    Assanis, D.; Karvounis, E. (Univ. of Illinois, Urbana, IL (United States)); Sekar, R.; Marr, W. (Argonne National Lab., IL (United States))

    1993-10-01T23:59:59.000Z

    A heat release correlation for oxygen-enriched diesel combustion is being developed through heat release analysis of cylinder pressure data from a single-cylinder diesel engine operating under various levels of oxygen enrichment. Results show that standard combustion correlations available in the literature do not accurately describe oxygen-enriched diesel combustion. A novel functional form is therefore proposed, which is shown to reproduce measured heat release profiles closely, under different operating conditions and levels of oxygen enrichment. The mathematical complexity of the associated curve-fitting problem is maintained at the same level of difficulty as for standard correlations. When the novel correlation is incorporated into a computer simulation of diesel engine operation with oxygen enrichment, the latter predicts pressure traces in excellent agreement with measured pressure data. This demonstrates the potential of the proposed combustion simulation to guide the application of oxygen-enriched technology successfully to a variety of multicylinder diesel systems.

  18. Underground coal gasification using oxygen and steam

    SciTech Connect (OSTI)

    Yang, L.H.; Zhang, X.; Liu, S. [China University of Mining & Technology, Xuzhou (China)

    2009-07-01T23:59:59.000Z

    In this paper, through model experiment of the underground coal gasification, the effects of pure oxygen gasification, oxygen-steam gasification, and moving-point gasification methods on the underground gasification process and gas quality were studied. Experiments showed that H{sub 2} and CO volume fraction in product gas during the pure oxygen gasification was 23.63-30.24% and 35.22-46.32%, respectively, with the gas heating value exceeding 11.00 MJ/m{sup 3}; under the oxygen-steam gasification, when the steam/oxygen ratio stood at 2: 1, gas compositions remained virtually stable and CO + H{sub 2} was basically between 61.66 and 71.29%. Moving-point gasification could effectively improve the changes in the cavity in the coal seams or the effects of roof inbreak on gas quality; the ratio of gas flowing quantity to oxygen supplying quantity was between 3.1:1 and 3.5:1 and took on the linear changes; on the basis of the test data, the reasons for gas quality changes under different gasification conditions were analyzed.

  19. Extinction curves in AGN

    E-Print Network [OSTI]

    B. Czerny

    2006-12-16T23:59:59.000Z

    The presence of the dust in the circumnuclear region strongly affects our view of the nucleus itself. The effect is strong in type 2 objects but weaker effect is likely to be present in type 1 objects as well. In these objects a correction to the observed optical/UV spectrum must be done in order to recover the intrinsic spectrum of a nucleus. The approach based on the extinction curve is convenient for that purpose so significant effort has been recently done in order to determine the extinction curve for the circumnuclear material. It seems clear that the circumnuclear dust is different from the average properties of the dust in the Interstellar Medium in our galaxy: the well known 2175 A feature is weak or absent in AGN nuclear dust, and the extinction curve at shorter wavelength does not seem to be rising as steeply. The circumnuclear dust is therefore more similar to SMC dust, or more likely, to the dust in very dense molecular clouds in our Galaxy. However, the exact shape of the extinction curve in the far UV is still a matter of debate, and various effects are difficult to disentangle.

  20. Risk Management in Biopharmaceutical Supply Chains

    E-Print Network [OSTI]

    Ma, Yao

    2011-01-01T23:59:59.000Z

    Supply Chain Risk Managementof Recent Work on Supply Chain Risk Management . . . . .M. , Supply chain risk management: Outlining an agenda for

  1. Petroleum Supply Monthly

    SciTech Connect (OSTI)

    NONE

    1996-02-01T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  2. Petroleum supply monthly

    SciTech Connect (OSTI)

    NONE

    1995-10-01T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  3. Oxygen partial pressure sensor

    DOE Patents [OSTI]

    Dees, D.W.

    1994-09-06T23:59:59.000Z

    A method for detecting oxygen partial pressure and an oxygen partial pressure sensor are provided. The method for measuring oxygen partial pressure includes contacting oxygen to a solid oxide electrolyte and measuring the subsequent change in electrical conductivity of the solid oxide electrolyte. A solid oxide electrolyte is utilized that contacts both a porous electrode and a nonporous electrode. The electrical conductivity of the solid oxide electrolyte is affected when oxygen from an exhaust stream permeates through the porous electrode to establish an equilibrium of oxygen anions in the electrolyte, thereby displacing electrons throughout the electrolyte to form an electron gradient. By adapting the two electrodes to sense a voltage potential between them, the change in electrolyte conductivity due to oxygen presence can be measured. 1 fig.

  4. Connecting curves for dynamical systems

    E-Print Network [OSTI]

    R. Gilmore; Jean-Marc Ginoux; Timothy Jones; C. Letellier; U. S. Freitas

    2010-03-08T23:59:59.000Z

    We introduce one dimensional sets to help describe and constrain the integral curves of an $n$ dimensional dynamical system. These curves provide more information about the system than the zero-dimensional sets (fixed points) do. In fact, these curves pass through the fixed points. Connecting curves are introduced using two different but equivalent definitions, one from dynamical systems theory, the other from differential geometry. We describe how to compute these curves and illustrate their properties by showing the connecting curves for a number of dynamical systems.

  5. MTBE/methanol supply

    SciTech Connect (OSTI)

    Simmons, R.E.

    1986-05-01T23:59:59.000Z

    U.S. methanol production has become economically competitive with imports due to de-escalation of natural gas price from $3.07 mm Btu in January 1985 to $2.07 mm Btu by December 1985. This has reversed the earlier supply outlook when it appeared that additional methanol plants would shutdown due to low cost imports. Current gas cost in conjunction with projections for continued excess supply prompted DuPont to restart their 250 mm gpy plant at Beaumont, Texas. Other former producers are contemplating restarting idle units.

  6. Ethanol Demand in United States Production of Oxygenate-limited Gasoline

    SciTech Connect (OSTI)

    Hadder, G.R.

    2000-08-16T23:59:59.000Z

    Ethanol competes with methyl tertiary butyl ether (MTBE) to satisfy oxygen, octane, and volume requirements of certain gasolines. However, MTBE has water quality problems that may create significant market opportunities for ethanol. Oak Ridge National Laboratory (ORNL) has used its Refinery Yield Model to estimate ethanol demand in gasolines with restricted use of MTBE. Reduction of the use of MTBE would increase the costs of gasoline production and possibly reduce the gasoline output of U.S. refineries. The potential gasoline supply problems of an MTBE ban could be mitigated by allowing a modest 3 vol percent MTBE in all gasoline. In the U.S. East and Gulf Coast gasoline producing regions, the 3 vol percent MTBE option results in costs that are 40 percent less than an MTBE ban. In the U.S. Midwest gasoline producing region, with already high use of ethanol, an MTBE ban has minimal effect on ethanol demand unless gasoline producers in other regions bid away the local supply of ethanol. The ethanol/MTBE issue gained momentum in March 2000 when the Clinton Administration announced that it would ask Congress to amend the Clean Air Act to provide the authority to significantly reduce or eliminate the use of MTBE; to ensure that air quality gains are not diminished as MTBE use is reduced; and to replace the existing oxygenate requirement in the Clean Air Act with a renewable fuel standard for all gasoline. Premises for the ORNL study are consistent with the Administration announcement, and the ethanol demand curve estimates of this study can be used to evaluate the impact of the Administration principles and related policy initiatives.

  7. Integrated turbomachine oxygen plant

    SciTech Connect (OSTI)

    Anand, Ashok Kumar; DePuy, Richard Anthony; Muthaiah, Veerappan

    2014-06-17T23:59:59.000Z

    An integrated turbomachine oxygen plant includes a turbomachine and an air separation unit. One or more compressor pathways flow compressed air from a compressor through one or more of a combustor and a turbine expander to cool the combustor and/or the turbine expander. An air separation unit is operably connected to the one or more compressor pathways and is configured to separate the compressed air into oxygen and oxygen-depleted air. A method of air separation in an integrated turbomachine oxygen plant includes compressing a flow of air in a compressor of a turbomachine. The compressed flow of air is flowed through one or more of a combustor and a turbine expander of the turbomachine to cool the combustor and/or the turbine expander. The compressed flow of air is directed to an air separation unit and is separated into oxygen and oxygen-depleted air.

  8. Oxygen ion conducting materials

    DOE Patents [OSTI]

    Carter, J. David; Wang, Xiaoping; Vaughey, John; Krumpelt, Michael

    2004-11-23T23:59:59.000Z

    An oxygen ion conducting ceramic oxide that has applications in industry including fuel cells, oxygen pumps, oxygen sensors, and separation membranes. The material is based on the idea that substituting a dopant into the host perovskite lattice of (La,Sr)MnO.sub.3 that prefers a coordination number lower than 6 will induce oxygen ion vacancies to form in the lattice. Because the oxygen ion conductivity of (La,Sr)MnO.sub.3 is low over a very large temperature range, the material exhibits a high overpotential when used. The inclusion of oxygen vacancies into the lattice by doping the material has been found to maintain the desirable properties of (La,Sr)MnO.sub.3, while significantly decreasing the experimentally observed overpotential.

  9. Oxygen ion conducting materials

    DOE Patents [OSTI]

    Vaughey, John; Krumpelt, Michael; Wang, Xiaoping; Carter, J. David

    2005-07-12T23:59:59.000Z

    An oxygen ion conducting ceramic oxide that has applications in industry including fuel cells, oxygen pumps, oxygen sensors, and separation membranes. The material is based on the idea that substituting a dopant into the host perovskite lattice of (La,Sr)MnO.sub.3 that prefers a coordination number lower than 6 will induce oxygen ion vacancies to form in the lattice. Because the oxygen ion conductivity of (La,Sr)MnO.sub.3 is low over a very large temperature range, the material exhibits a high overpotential when used. The inclusion of oxygen vacancies into the lattice by doping the material has been found to maintain the desirable properties of (La,Sr)MnO.sub.3, while significantly decreasing the experimentally observed overpotential.

  10. Oxygen ion conducting materials

    DOE Patents [OSTI]

    Vaughey, John (Elmhurst, IL); Krumpelt, Michael (Naperville, IL); Wang, Xiaoping (Downers Grove, IL); Carter, J. David (Bolingbrook, IL)

    2003-01-01T23:59:59.000Z

    An oxygen ion conducting ceramic oxide that has applications in industry including fuel cells, oxygen pumps, oxygen sensors, and separation membranes. The material is based on the idea that substituting a dopant into the host perovskite lattice of (La,Sr)MnO.sub.3 that prefers a coordination number lower than 6 will induce oxygen ion vacancies to form in the lattice. Because the oxygen ion conductivity of (La,Sr)MnO.sub.3 is low over a very large temperature range, the material exhibits a high overpotential when used. The inclusion of oxygen vacancies into the lattice by doping the material has been found to maintain the desirable properties of (La,Sr)MnO.sub.3, while significantly decreasing the experimentally observed overpotential.

  11. Oxygen generator for medical applications (USIC)

    SciTech Connect (OSTI)

    Staiger, C. L.

    2012-03-01T23:59:59.000Z

    The overall Project objective is to develop a portable, non-cryogenic oxygen generator capable of supplying medical grade oxygen at sufficient flow rates to allow the field application of the Topical Hyperbaric Oxygen Therapy (THOT{reg_sign}) developed by Numotech, Inc. This project was sponsored by the U.S. Department of Energy Global Initiatives for Proliferation Prevention (GIPP) and is managed by collaboration between Sandia National Laboratories (SNL), Numotech, Inc, and LLC SPE 'Spektr-Conversion.' The project had two phases, with the objective of Phase I being to develop, build and test a laboratory prototype of the membrane-pressure swing adsorber (PSA) system producing at 15 L/min of oxygen with a minimum of 98% oxygen purity. Phase II objectives were to further refine and identify the pre-requisites needed for a commercial product and to determine the feasibility of producing 15 L/min of oxygen with a minimum oxygen purity of 99%. In Phase I, Spektr built up the necessary infrastructure to perform experimental work and proceeded to build and demonstrate a membrane-PSA laboratory prototype capable of producing 98% purity oxygen at a flow rate of 5 L/min. Spektr offered a plausible path to scale up the process for 15 L/min. Based on the success and experimental results obtained in Phase I, Spektr performed work in three areas for Phase II: construction of a 15 L/min PSA; investigation of compressor requirements for the front end of the membrane/PSA system; and performing modeling and simulation of assess the feasibility of producing oxygen with a purity greater than 99%. Spektr successfully completed all of the tasks under Phase II. A prototype 15 L/min PSA was constructed and operated. Spektr determined that no 'off the shelf' air compressors met all of the specifications required for the membrane-PSA, so a custom compressor will likely need to be built. Modeling and simulation concluded that production of oxygen with purities greater than 99% was possible using a Membrane-PSA system.

  12. Fiber Supply Associate Company Overview

    E-Print Network [OSTI]

    Mazzotti, Frank

    materials acquisition, harvesting, logistics coordination, contract negotiations, and inventory management, Purchasing, Industrial Engineering, Operations management, Materials Management, Supply Chain) Authorized leadership roles such as Fiber Specialist, Fiber Supply Manager, Region Manager, Director, General Manager

  13. OXYGEN ENHANCED COMBUSTION FOR NOx CONTROL

    SciTech Connect (OSTI)

    Lawrence E. Bool; Jack C. Chen; David R. Thompson

    2000-07-01T23:59:59.000Z

    Increased environmental regulations will require utility boilers to reduce NO{sub x} emissions to less than 0.15lb/MMBtu in the near term. Conventional technologies such as Selective Catalytic Reduction (SCR) and Selective Non-Catalytic Reduction (SNCR) are unable to achieve these lowered emission levels without substantially higher costs and major operating problems. Oxygen enhanced combustion is a novel technology that allows utilities to meet the NO{sub x} emission requirements without the operational problems that occur with SCR and SNCR. Furthermore, oxygen enhanced combustion can achieve these NO{sub x} limits at costs lower than conventional technologies. The objective of this program is to demonstrate the use of oxygen enhanced combustion as a technical and economical method of meeting the EPA State Implementation Plan for NO{sub x} reduction to less than 0.15lb/MMBtu for a wide range of boilers and coal. The oxygen enhanced coal combustion program (Task 1) focused this quarter on the specific objective of exploration of the impact of oxygen enrichment on NO{sub x} formation utilizing small-scale combustors for parametric testing. Research efforts toward understanding any limitations to the applicability of the technology to different burners and fuels such as different types of coal are underway. The objective of the oxygen transport membrane (OTM) materials development program (Task 2.1) is to ascertain a suitable material composition that can be fabricated into dense tubes capable of producing the target oxygen flux under the operating conditions. This requires that the material have sufficient oxygen permeation resulting from high oxygen ion conductivity, high electronic conductivity and high oxygen surface exchange rate. The OTM element development program (Task 2.2) objective is to develop, fabricate and characterize OTM elements for laboratory and pilot reactors utilizing quality control parameters to ensure reproducibility and superior performance. A specific goal is to achieve a material that will sinter to desired density without compromising other variables such as reaction to binder systems or phase purity. Oxygen-enhanced combustion requires a facility which is capable of supplying high purity oxygen (>99.5%) at low costs. This goal can be achieved through the thermal integration of high temperature air separation with ceramic OTM. The objective of the OTM process development program (Task 2.3) is to demonstrate successfully the program objectives on a lab-scale single OTM tube reactor under process conditions comparable to those of an optimum large-scale oxygen facility. This quarterly technical progress report will summarize work accomplished for the Program through the first quarter April--June 2000 in the following task areas: Task 1 Oxygen Enhanced Coal Combustion; Task 2 Oxygen Transport Membranes; and Task 4 Program Management.

  14. Fuel cell power supply with oxidant and fuel gas switching

    DOE Patents [OSTI]

    McElroy, James F. (Hamilton, MA); Chludzinski, Paul J. (Swampscott, MA); Dantowitz, Philip (Peabody, MA)

    1987-01-01T23:59:59.000Z

    This invention relates to a fuel cell vehicular power plant. Fuel for the fuel stack is supplied by a hydrocarbon (methanol) catalytic cracking reactor and CO shift reactor. A water electrolysis subsystem is associated with the stack. During low power operation part of the fuel cell power is used to electrolyze water with hydrogen and oxygen electrolysis products being stored in pressure vessels. During peak power intervals, viz, during acceleration or start-up, pure oxygen and pure hydrogen from the pressure vessel are supplied as the reaction gases to the cathodes and anodes in place of air and methanol reformate. This allows the fuel cell stack to be sized for normal low power/air operation but with a peak power capacity several times greater than that for normal operation.

  15. Fuel cell power supply with oxidant and fuel gas switching

    DOE Patents [OSTI]

    McElroy, J.F.; Chludzinski, P.J.; Dantowitz, P.

    1987-04-14T23:59:59.000Z

    This invention relates to a fuel cell vehicular power plant. Fuel for the fuel stack is supplied by a hydrocarbon (methanol) catalytic cracking reactor and CO shift reactor. A water electrolysis subsystem is associated with the stack. During low power operation part of the fuel cell power is used to electrolyze water with hydrogen and oxygen electrolysis products being stored in pressure vessels. During peak power intervals, viz, during acceleration or start-up, pure oxygen and pure hydrogen from the pressure vessel are supplied as the reaction gases to the cathodes and anodes in place of air and methanol reformate. This allows the fuel cell stack to be sized for normal low power/air operation but with a peak power capacity several times greater than that for normal operation. 2 figs.

  16. Petroleum Supply Monthly

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122Commercial Consumers (NumberThousandby thePricePricetheTable 1. U.S. Supply,

  17. Langevin Equation on Fractal Curves

    E-Print Network [OSTI]

    Seema Satin; A. D. Gangal

    2014-04-28T23:59:59.000Z

    We analyse a random motion of a particle on a fractal curve, using Langevin approach. This involves defining a new velocity in terms of mass of the fractal curve, as defined in recent work. The geometry of the fractal curve, hence plays an important role in this analysis. A Langevin equation with a particular noise model is thus proposed and solved using techniques of the newly developed $F^\\alpha$-Calculus .

  18. Quantum curves and topological recursion

    E-Print Network [OSTI]

    Paul Norbury

    2015-02-16T23:59:59.000Z

    This is a survey article describing the relationship between quantum curves and topological recursion. A quantum curve is a Schr\\"odinger operator-like noncommutative analogue of a plane curve which encodes (quantum) enumerative invariants in a new and interesting way. The Schr\\"odinger operator annihilates a wave function which can be constructed using the WKB method, and conjecturally constructed in a rather different way via topological recursion.

  19. Variable oxygen/nitrogen enriched intake air system for internal combustion engine applications

    DOE Patents [OSTI]

    Poola, Ramesh B. (Woodridge, IL); Sekar, Ramanujam R. (Naperville, IL); Cole, Roger L. (Elmhurst, IL)

    1997-01-01T23:59:59.000Z

    An air supply control system for selectively supplying ambient air, oxygen enriched air and nitrogen enriched air to an intake of an internal combustion engine includes an air mixing chamber that is in fluid communication with the air intake. At least a portion of the ambient air flowing to the mixing chamber is selectively diverted through a secondary path that includes a selectively permeable air separating membrane device due a differential pressure established across the air separating membrane. The permeable membrane device separates a portion of the nitrogen in the ambient air so that oxygen enriched air (permeate) and nitrogen enriched air (retentate) are produced. The oxygen enriched air and the nitrogen enriched air can be selectively supplied to the mixing chamber or expelled to atmosphere. Alternatively, a portion of the nitrogen enriched air can be supplied through another control valve to a monatomic-nitrogen plasma generator device so that atomic nitrogen produced from the nitrogen enriched air can be then injected into the exhaust of the engine. The oxygen enriched air or the nitrogen enriched air becomes mixed with the ambient air in the mixing chamber and then the mixed air is supplied to the intake of the engine. As a result, the air being supplied to the intake of the engine can be regulated with respect to the concentration of oxygen and/or nitrogen.

  20. High Selectivity Oxygen Delignification

    SciTech Connect (OSTI)

    Lucian A. Lucia

    2005-11-15T23:59:59.000Z

    Project Objective: The objectives of this project are as follows: (1) Examine the physical and chemical characteristics of a partner mill pre- and post-oxygen delignified pulp and compare them to lab generated oxygen delignified pulps; (2) Apply the chemical selectivity enhancement system to the partner pre-oxygen delignified pulps under mill conditions (with and without any predetermined amounts of carryover) to determine how efficiently viscosity is preserved, how well selectivity is enhanced, if strength is improved, measure any yield differences and/or bleachability differences; and (3) Initiate a mill scale oxygen delignification run using the selectivity enhancement agent, collect the mill data, analyze it, and propose any future plans for implementation.

  1. EMSL - oxygen-plasma

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    oxygen-plasma en Conversion of 1,2-Propylene Glycol on Rutile TiO2(110). http:www.emsl.pnl.govemslwebpublicationsconversion-12-propylene-glycol-rutile-tio2110

  2. Heat Supply Who What Where and -Why

    E-Print Network [OSTI]

    Columbia University

    ................................................. 6 District-heating (DH) supply: key figures .............................. 6 What is biomass Geothermics ..........................................................................11 Waste for heat supplyHeat Supply in Denmark Who What Where and - Why #12;Title: Heat Supply in Denmark - Who What Where

  3. Random Curves by Conformal Welding

    E-Print Network [OSTI]

    K. Astala; P. Jones; A. Kupiainen; E. Saksman

    2009-12-17T23:59:59.000Z

    We construct a conformally invariant random family of closed curves in the plane by welding of random homeomorphisms of the unit circle given in terms of the exponential of Gaussian Free Field. We conjecture that our curves are locally related to SLE$(\\kappa)$ for $\\kappa<4$.

  4. Random Curves by Conformal Welding

    E-Print Network [OSTI]

    Astala, K; Kupiainen, A; Saksman, E

    2009-01-01T23:59:59.000Z

    We construct a conformally invariant random family of closed curves in the plane by welding of random homeomorphisms of the unit circle given in terms of the exponential of Gaussian Free Field. We conjecture that our curves are locally related to SLE$(\\kappa)$ for $\\kappa<4$.

  5. Fourier duality of quantum curves

    E-Print Network [OSTI]

    Luu, Martin

    2015-01-01T23:59:59.000Z

    There are two different ways to deform a quantum curve along the flows of the KP hierarchy. We clarify the relation between the two KP orbits: In the framework of suitable connections attached to the quantum curve they are related by a local Fourier duality. As an application we give a conceptual proof of duality results in 2D quantum gravity.

  6. Switching power supply

    DOE Patents [OSTI]

    Mihalka, A.M.

    1984-06-05T23:59:59.000Z

    The invention is a repratable capacitor charging, switching power supply. A ferrite transformer steps up a dc input. The transformer primary is in a full bridge configuration utilizing power MOSFETs as the bridge switches. The transformer secondary is fed into a high voltage, full wave rectifier whose output is connected directly to the energy storage capacitor. The transformer is designed to provide adequate leakage inductance to limit capacitor current. The MOSFETs are switched to the variable frequency from 20 to 50 kHz to charge a capacitor from 0.6 kV. The peak current in a transformer primary and secondary is controlled by increasing the pulse width as the capacitor charges. A digital ripple counter counts pulses and after a preselected desired number is reached an up-counter is clocked.

  7. NNSA TRITIUM SUPPLY CHAIN

    SciTech Connect (OSTI)

    Wyrick, Steven [Savannah River National Laboratory, Aiken, SC, USA; Cordaro, Joseph [Savannah River National Laboratory, Aiken, SC, USA; Founds, Nanette [National Nuclear Security Administration, Albuquerque, NM, USA; Chambellan, Curtis [National Nuclear Security Administration, Albuquerque, NM, USA

    2013-08-21T23:59:59.000Z

    Savannah River Site plays a critical role in the Tritium Production Supply Chain for the National Nuclear Security Administration (NNSA). The entire process includes: • Production of Tritium Producing Burnable Absorber Rods (TPBARs) at the Westinghouse WesDyne Nuclear Fuels Plant in Columbia, South Carolina • Production of unobligated Low Enriched Uranium (LEU) at the United States Enrichment Corporation (USEC) in Portsmouth, Ohio • Irradiation of TPBARs with the LEU at the Tennessee Valley Authority (TVA) Watts Bar Reactor • Extraction of tritium from the irradiated TPBARs at the Tritium Extraction Facility (TEF) at Savannah River Site • Processing the tritium at the Savannah River Site, which includes removal of nonhydrogen species and separation of the hydrogen isotopes of protium, deuterium and tritium.

  8. Sustainable Biomass Supply Systems

    SciTech Connect (OSTI)

    Erin Searcy; Dave Muth; Erin Wilkerson; Shahab Sokansanj; Bryan Jenkins; Peter Titman; Nathan Parker; Quinn Hart; Richard Nelson

    2009-04-01T23:59:59.000Z

    The U.S. Department of Energy (DOE) aims to displace 30% of the 2004 gasoline use (60 billion gal/yr) with biofuels by 2030 as outlined in the Energy Independence and Security Act of 2007, which will require 700 million tons of biomass to be sustainably delivered to biorefineries annually. Lignocellulosic biomass will make an important contribution towards meeting DOE’s ethanol production goals. For the biofuels industry to be an economically viable enterprise, the feedstock supply system (i.e., moving the biomass from the field to the refinery) cannot contribute more that 30% of the total cost of the biofuel production. The Idaho National Laboratory in collaboration with Oak Ridge National Laboratory, University of California, Davis and Kansas State University are developing a set of tools for identifying economical, sustainable feedstocks on a regional basis based on biorefinery siting.

  9. A calcium oxygen secondary battery

    SciTech Connect (OSTI)

    Pujare, N.U.; Semkow, K.W.; Sammells, A.F.

    1988-01-01T23:59:59.000Z

    The authors report preliminary work performed in their laboratory on a high-temperature electrochemically reversible calcium-oxygen cell. Following an analogous strategy to that recently discussed for the lithium-oxygen secondary system, this calcium-oxygen cell utilizes stabilized zirconia oxygen vacancy conducting solid electrolytes to achieve effective separation between half-cell reactions.

  10. Reliability Estimates for Power Supplies

    SciTech Connect (OSTI)

    Lee C. Cadwallader; Peter I. Petersen

    2005-09-01T23:59:59.000Z

    Failure rates for large power supplies at a fusion facility are critical knowledge needed to estimate availability of the facility or to set priorties for repairs and spare components. A study of the "failure to operate on demand" and "failure to continue to operate" failure rates has been performed for the large power supplies at DIII-D, which provide power to the magnet coils, the neutral beam injectors, the electron cyclotron heating systems, and the fast wave systems. When one of the power supplies fails to operate, the research program has to be either temporarily changed or halted. If one of the power supplies for the toroidal or ohmic heating coils fails, the operations have to be suspended or the research is continued at de-rated parameters until a repair is completed. If one of the power supplies used in the auxiliary plasma heating systems fails the research is often temporarily changed until a repair is completed. The power supplies are operated remotely and repairs are only performed when the power supplies are off line, so that failure of a power supply does not cause any risk to personnel. The DIII-D Trouble Report database was used to determine the number of power supply faults (over 1,700 reports), and tokamak annual operations data supplied the number of shots, operating times, and power supply usage for the DIII-D operating campaigns between mid-1987 and 2004. Where possible, these power supply failure rates from DIII-D will be compared to similar work that has been performed for the Joint European Torus equipment. These independent data sets support validation of the fusion-specific failure rate values.

  11. Industry Supply Chain Development (Ohio)

    Broader source: Energy.gov [DOE]

    Supply Chain Development programs are focused on targeted industries that have significant growth opportunities for Ohio's existing manufacturing sector from emerging energy resources and...

  12. Tariffs with Dynamic Supply Response

    E-Print Network [OSTI]

    Karp, Larry

    1985-01-01T23:59:59.000Z

    Giannini FDN iibrary TARIFFS WITH DYNAMIC SUPPLY RESWNSEpaper studies the optimal tariff in a dynamic framework. Thesellers, the optimal tariff is dynam- ically inconsistent;

  13. Power Supply Synchronization without Communication

    E-Print Network [OSTI]

    Moehlis, Jeff

    1 Power Supply Synchronization without Communication Leonardo A. B. T^orres, Jo~ao P. Hespanha, Jeff Moehlis Abstract--We consider the synchronization of power supplies in an isolated grid with multiple small-to-medium power sources. We show how to achieve a coordinated or synchronized behavior

  14. WATER SUPPLY A Handbook on

    E-Print Network [OSTI]

    US Army Corps of Engineers

    WATER SUPPLY HANDBOOK A Handbook on Water Supply Planning and Resource Management Institute for Water Resources Water Resources Support Center U.S. Army Corps of Engineers 7701 Telegraph Road Studies Division December 1998 Revised IWR Report 96-PS-4 #12;U.S. Army Institute for Water Resources

  15. REGIONAL WATER SUPPLY PLANNING AND

    E-Print Network [OSTI]

    Mays, Larry W.

    CHAPTER 3 REGIONAL WATER SUPPLY PLANNING AND CAPACITY EXPANSION MODELS Messele Z. Ejeta California Department of Water Resources Sacramento, California Larry W. Mays Department of Civil and Environmental Engineering Arizona State University Tempe, Arizona 3.1 INTRODUCTION Water supply planning on a regional scale

  16. GLOBAL WOOD SUPPLY Sten Nilsson

    E-Print Network [OSTI]

    GLOBAL WOOD SUPPLY Sten Nilsson Biomass and Resource Efficiency: the need for a supply led approach the wood come from? Western EU Deficit Eastern EU Deficit Rest of Eastern Europe Balanced Russia Rest of Eastern Europe Balanced Russia Is probably at production ceiling under current conditions Japan

  17. Parabolic curves in Lie groups

    SciTech Connect (OSTI)

    Pauley, Michael [School of Mathematics and Statistics, University of Western Australia, 35 Stirling Highway, Crawley, Western Australia 6009 (Australia)

    2010-05-15T23:59:59.000Z

    To interpolate a sequence of points in Euclidean space, parabolic splines can be used. These are curves which are piecewise quadratic. To interpolate between points in a (semi-)Riemannian manifold, we could look for curves such that the second covariant derivative of the velocity is zero. We call such curves Jupp and Kent quadratics or JK-quadratics because they are a special case of the cubic curves advocated by Jupp and Kent. When the manifold is a Lie group with bi-invariant metric, we can relate JK-quadratics to null Lie quadratics which arise from another interpolation problem. We solve JK-quadratics in the Lie groups SO(3) and SO(1,2) and in the sphere and hyperbolic plane, by relating them to the differential equation for a quantum harmonic oscillator00.

  18. Petroleum Supply Monthly, September 1984

    SciTech Connect (OSTI)

    Not Available

    1984-11-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for September 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. The focus article discusses EIA data series for crude oil imports, motor gasoline supplied, and distillate and residual fuel oil supplied, as well as crude oil production. A companion article, An Evaluation of Crude Oil Production Statistics beginning on page xvii compares crude oil production volumes reported in EIA's petroleum supply publications with those shown in state reports.

  19. Petroleum supply monthly, August 1993

    SciTech Connect (OSTI)

    Not Available

    1993-09-01T23:59:59.000Z

    This publication the Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report, (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data presented are divided into Summary Statistics and Detailed Statistics.

  20. OXYGEN TRANSPORT CERAMIC MEMBRANES

    SciTech Connect (OSTI)

    Dr. Sukumar Bandopadhyay; Dr. Nagendra Nagabhushana

    2003-01-01T23:59:59.000Z

    In the present quarter, the possibility of using a more complex interfacial engineering approach to the development of reliable and stable oxygen transport perovskite ceramic membranes/metal seals is discussed. Experiments are presented and ceramic/metal interactions are characterized. Crack growth and fracture toughness of the membrane in the reducing conditions are also discussed. Future work regarding this approach is proposed are evaluated for strength and fracture in oxygen gradient conditions. Oxygen gradients are created in tubular membranes by insulating the inner surface from the reducing environment by platinum foils. Fracture in these test conditions is observed to have a gradient in trans and inter-granular fracture as opposed to pure trans-granular fracture observed in homogeneous conditions. Fracture gradients are reasoned to be due to oxygen gradient set up in the membrane, variation in stoichiometry across the thickness and due to varying decomposition of the parent perovskite. The studies are useful in predicting fracture criterion in actual reactor conditions and in understanding the initial evolution of fracture processes.

  1. Direct Observation of the Oxygenated Species during Oxygen Reduction...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Direct Observation of the Oxygenated Species during Oxygen Reduction on a Platinum Fuel Cell Cathode Friday, December 20, 2013 Fuel Cell Figure 1 Figure 1. In situ x-ray...

  2. Incorporating Experience Curves in Appliance Standards Analysis

    E-Print Network [OSTI]

    Desroches, Louis-Benoit

    2012-01-01T23:59:59.000Z

    experience curves for wind farms. Energy Policy 33, 133-150.curves for wind power. Energy Policy 30, 1181- Jakob, M. ,

  3. Improve supply chain resilience by multi-stage supply chain

    E-Print Network [OSTI]

    Xu, Jie, M. Eng. Massachusetts Institute of Technology

    2009-01-01T23:59:59.000Z

    Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

  4. Improving supply chain resilience by multi-stage supply chain

    E-Print Network [OSTI]

    Yang, Jingxia, M. Eng, Massachusetts Institute of Technology

    2009-01-01T23:59:59.000Z

    Due to the global expansion of Company A's supply chain network, it is becoming more vulnerable to many disruptions. These disruptions often incur additional costs; and require time to respond to and recover from these ...

  5. Water supply and demand in an energy supply model

    SciTech Connect (OSTI)

    Abbey, D; Loose, V

    1980-12-01T23:59:59.000Z

    This report describes a tool for water and energy-related policy analysis, the development of a water supply and demand sector in a linear programming model of energy supply in the United States. The model allows adjustments in the input mix and plant siting in response to water scarcity. Thus, on the demand side energy conversion facilities can substitute more costly dry cooling systems for conventional evaporative systems. On the supply side groundwater and water purchased from irrigators are available as more costly alternatives to unappropriated surface water. Water supply data is developed for 30 regions in 10 Western states. Preliminary results for a 1990 energy demand scenario suggest that, at this level of spatial analysis, water availability plays a minor role in plant siting. Future policy applications of the modeling system are discussed including the evaluation of alternative patterns of synthetic fuels development.

  6. Petroleum supply monthly, February 1994

    SciTech Connect (OSTI)

    Not Available

    1994-03-01T23:59:59.000Z

    The Petroleum Supply Monthly presents data describing the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders; operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data are divided into two sections: Summary statistics and Detailed statistics.

  7. Petroleum supply monthly, April 1994

    SciTech Connect (OSTI)

    Not Available

    1994-04-01T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

  8. Oxygen Concentration Microgradients for Cell Culture

    E-Print Network [OSTI]

    Park, Jaehyun

    2010-01-01T23:59:59.000Z

    The Chemotactic Effect of Oxygen on Bacteria,” J. Pathol.Measurement and Control of Oxygen Levels in MicrofluidicA Microfabricated Electrochemical Oxygen Generator for High-

  9. Oxygen abundances in the most oxygen-rich spiral galaxies

    E-Print Network [OSTI]

    L. S. Pilyugin; T. X. Thuan; J. M. Vilchez

    2006-01-06T23:59:59.000Z

    Oxygen abundances in the spiral galaxies expected to be richest in oxygen are estimated. The new abundance determinations are based on the recently discovered ff-relation between auroral and nebular oxygen line fluxes in HII regions. We find that the maximum gas-phase oxygen abundance in the central regions of spiral galaxies is 12+log(O/H)~8.75. This value is significantly lower than the previously accepted value. The central oxygen abundance in the Milky Way is similar to that in other large spirals.

  10. High pressure oxygen furnace

    DOE Patents [OSTI]

    Morris, Donald E. (Kensington, CA)

    1992-01-01T23:59:59.000Z

    A high temperature high pressure oxygen furnace having a hybrid partially externally heated construction is disclosed. A metallic bar fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 inch bar stock and has a length of about 17 inches. This bar stock is gun drilled for over 16 inches of its length with 0.400 inch aperture to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the bar is provided with a small support aperture into which both a support and a thermocouple can be inserted. The closed end of the gun drilled bar is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior.

  11. High pressure oxygen furnace

    DOE Patents [OSTI]

    Morris, D.E.

    1992-07-14T23:59:59.000Z

    A high temperature high pressure oxygen furnace having a hybrid partially externally heated construction is disclosed. A metallic bar fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized, the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 inch bar stock and has a length of about 17 inches. This bar stock is gun drilled for over 16 inches of its length with 0.400 inch aperture to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the bar is provided with a small support aperture into which both a support and a thermocouple can be inserted. The closed end of the gun drilled bar is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior. 5 figs.

  12. Optimal Monetary Policy with a Convex Phillips Curve

    E-Print Network [OSTI]

    Tambakis, Demosthenes N

    that inflation’s response to demand pressure is nonlinear and built this into estimation using the inverse unemployment rate. 9 Equation (6) holds regardless of the value of k. Because UN > ?, it requires that ?t > ?? for Ut to not diverge. Note... supply shocks, such as those of the 1970s. The convex Phillips curve functional form in this paper follows Debelle and Laxton (1997) and Laxton, Rose and Tambakis (1999). 6 At the aggregate level, convexity can be traced to the traditional Keynesian...

  13. The 3He Supply Problem

    SciTech Connect (OSTI)

    Kouzes, Richard T.

    2009-05-01T23:59:59.000Z

    One of the main uses for 3He is in gas proportional counters for neutron detection. Radiation portal monitors deployed for homeland security and non-proliferation use such detectors. Other uses of 3He are for research detectors, commercial instruments, well logging detectors, dilution refrigerators, for targets or cooling in nuclear research, and for basic research in condensed matter physics. The US supply of 3He comes almost entirely from the decay of tritium used in nuclear weapons by the US and Russia. A few other countries contribute a small amount to the world’s 3He supply. Due to the large increase in use of 3He for homeland security, the supply has dwindled, and can no longer meet the demand. This white paper reviews the problems of supply, utilization, and alternatives.

  14. Effective contracts in supply chains

    E-Print Network [OSTI]

    Shum, Wanhang

    2007-01-01T23:59:59.000Z

    In the past decade, we have seen significant increase in the level of outsourcing in many industries. This increase in the level of outsourcing increases the importance of implementing effective contracts in supply chains. ...

  15. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; T. Nithyanantham; X.-D Zhou; Y-W. Sin; H.U. Anderson; Alan Jacobson; C.A. Mims

    2005-08-01T23:59:59.000Z

    The present quarterly report describes some of the investigations on the structural properties of dense OTM bars provided by Praxair and studies on newer composition of Ti doped LSF. In the previous research, the reference point of oxygen occupancy was determined and verified. In the current research, the oxygen occupancy was investigated at 1200 C as a function of oxygen activity and compared with that at 1000 C. The cause of bumps at about 200 C was also investigated by using different heating and cooling rates during TGA. The fracture toughness of LSFT and dual phase membranes at room temperature is an important mechanical property. Vicker's indentation method was used to evaluate this toughness. Through this technique, a K{sub Ic} (Mode-I Fracture Toughness) value is attained by means of semi-empirical correlations between the indentation load and the length of the cracks emanating from the corresponding Vickers indentation impression. In the present investigation, crack propagation behavior was extensively analyzed in order to understand the strengthening mechanisms involved in the non-transforming La based ceramic composites. Cracks were generated using Vicker's indenter and used to identify and evaluate the toughening mechanisms involved. Preliminary results of an electron microscopy study of the origin of the slow kinetics on reduction of ferrites have been obtained. The slow kinetics appear to be related to a non-equilibrium reduction pathway that initially results in the formation of iron particles. At long times, equilibrium can be reestablished with recovery of the perovskite phase. Modeling of the isotopic transients on operating membranes (LSCrF-2828 at 900 C) and a ''frozen'' isotope profile have been analyzed in conjunction with a 1-D model to reveal the gradient in oxygen diffusivity through the membrane under conditions of high chemical gradients.

  16. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; T. Nithyanantham; X.-D Zhou; Y-W. Sin; H.U. Anderson; Alan Jacobson; C.A. Mims

    2005-02-01T23:59:59.000Z

    The present quarterly report describes some of the investigations on the structural properties of dense OTM bars provided by Praxair and studies on newer composition of Ti doped LSF. The in situ electrical conductivity and Seebeck coefficient measurements were made on LSFT at 1000 and 1200 C over the oxygen activity range from air to 10{sup -15} atm. The electrical conductivity measurements exhibited a p to n type transition at an oxygen activity of 1 x 10{sup -10} at 1000 C and 1 x 10{sup -6} at 1200 C. Thermogravimetric studies were also carried out over the same oxygen activities and temperatures. Based on the results of these measurements, the chemical and mechanical stability range of LSFT were determined and defect structure was established. The studies on the fracture toughness of the LSFT and dual phase membranes exposed to air and N{sub 2} at 1000 C was done and the XRD and SEM analysis of the specimens were carried out to understand the structural and microstructural changes. The membranes that are exposed to high temperatures at an inert and a reactive atmosphere undergo many structural and chemical changes which affect the mechanical properties. A complete transformation of fracture behavior was observed in the N{sub 2} treated LSFT samples. Further results to investigate the origin of the slow kinetics on reduction of ferrites have been obtained. The slow kinetics appear to be related to a non-equilibrium reduction pathway that initially results in the formation of iron particles. At long times, equilibrium can be reestablished with recovery of the perovskite phase. Recent results on transient kinetic data are presented. The 2-D modeling of oxygen movement has been undertaken in order to fit isotope data. The model is used to study ''frozen'' profiles in patterned or composite membranes.

  17. Argonne Premium Coal Sample Bank The Argonne Premium Coal (APC) Sample Bank can supply

    E-Print Network [OSTI]

    Maranas, Costas

    Argonne Premium Coal Sample Bank Background Overview T The Argonne Premium Coal (APC) Sample Bank can supply researchers with highly uniform, well-protected coal samples unexposed to oxygen. Researchers investigating coal structure, properties, and behavior can benefit greatly from these samples

  18. Oxygen Transport Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay

    2008-08-30T23:59:59.000Z

    The focus of this research was to develop new membrane materials by synthesizing different compounds and determining their defect structures, crystallographic structures and electrical properties. In addition to measuring electrical conductivity, oxygen vacancy concentration was also evaluated using thermogravimetry, Neutron diffraction and Moessbauer Spectroscopy. The reducing conditions (CO{sub 2}/CO/H{sub 2} gas mixtures with steam) as encountered in a reactor environment can be expected to have significant influence on the mechanical properties of the oxides membranes. Various La based materials with and without Ti were selected as candidate membrane materials for OTM. The maximum electrical conductivity of LSF in air as a function of temperature was achieved at < 600 C and depends on the concentration of Sr (acceptor dopant). Oxygen occupancy in LSF was estimated using Neutron diffractometry and Moessbauer Spectroscopy by measuring magnetic moment changes depending on the Fe{sup 3+} and Fe{sup 4+} ratio. After extensive studies of candidate materials, lanthanum ferrites (LSF and LSFT) were selected as the favored materials for the oxygen transport membrane (OTM). LSF is a very good material for an OTM because of its high electronic and oxygen ionic conductivity if long term stability and mechanical strength are improved. LSFT not only exhibits p-type behavior in the high oxygen activity regime, but also has n-type conduction in reducing atmospheres. Higher concentrations of oxygen vacancies in the low oxygen activity regime may improve the performance of LSFT as an OTM. The hole concentration is related to the difference in the acceptor and donor concentration by the relation p = [Sr'{sub La}]-[Ti{sm_bullet}{sub Fe}]. The chemical formulation predicts that the hole concentration is, p = 0.8-0.45 or 0.35. Experimental measurements indicated that p is about {approx} 0.35. The activation energy of conduction is 0.2 eV which implies that LSCF conducts via the small polaron conduction mechanism. Scanning transmission electron microscopy (STEM) and electron energy loss spectroscopy (EELS) were used to develop strategies to detect and characterize vacancy creation, dopant segregations and defect association in the oxygen conducting membrane material. The pO{sub 2} and temperature dependence of the conductivity, non-stoichiometry and thermal-expansion behavior of compositions with increasing complexity of substitution on the perovskite A and B sites were studied. Studies with the perovskite structure show anomalous behavior at low oxygen partial pressures (<10{sup -5} atm). The anomalies are due to non-equilibrium effects and can be avoided by using very strict criteria for the attainment of equilibrium. The slowness of the oxygen equilibration kinetics arises from two different mechanisms. In the first, a two phase region occurs between an oxygen vacancy ordered phase such as brownmillerite SrFeO{sub 2.5} and perovskite SrFeO{sub 3-x}. The slow kinetics is associated with crossing the two phase region. The width of the miscibility gap decreases with increasing temperature and consequently the effect is less pronounced at higher temperature. The preferred kinetic pathway to reduction of perovskite ferrites when the vacancy concentration corresponds to the formation of significant concentrations of Fe{sup 2+} is via the formation of a Ruddlesden-Popper (RP) phases as clearly observed in the case of La{sub 0.5}Sr{sub 0.5}FeO{sub 3-x} where LaSrFeO{sub 4} is found together with Fe. In more complex compositions, such as LSFTO, iron or iron rich phases are observed locally with no evidence for the presence of discrete RP phase. Fracture strength of tubular perovskite membranes was determined in air and in reducing atmospheric conditions. The strength of the membrane decreased with temperature and severity of reducing conditions although the strength distribution (Weibull parameter, m) was relatively unaltered. Surface and volume dominated the fracture origins and the overall fracture was purely transgranular. The dual phas

  19. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; N. Nagabhushana; T. Nithyanantham; X.-D Zhou; Y-W. Sin; H.U. Anderson; Alan Jacobson; C.A. Mims

    2005-02-01T23:59:59.000Z

    The present quarterly report describes some of the investigations on the structural properties of dense OTM bars provided by Praxair and studies on newer composition of Ti doped LSF. Thermogravimetric analysis (TGA) was carried out on La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-{delta}} to investigate oxygen deficiency ({delta}) of the sample. The TGA was performed in a controlled atmosphere using oxygen, argon, carbon monoxide and carbon dioxide with adjustable gas flow rates. In this experiment, the weight loss and gain of La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-{delta}} was directly measured by TGA. The weight change of the sample was evaluated at between 600 and 1250 C in air or 1000 C as a function of oxygen partial pressure. The oxygen deficiencies calculated from TGA data as a function of oxygen activity and temperature will be estimated and compared with that from neutron diffraction measurement in air. The LSFT and LSFT/CGO membranes were fabricated from the powder obtained from Praxair Specialty Ceramics. The sintered membranes were subjected to microstructure analysis and hardness analysis. The LSFT membrane is composed of fine grains with two kinds of grain morphology. The grain size distribution was characterized using image analysis. In LSFT/CGO membrane a lot of grain pullout was observed from the less dense, porous phase. The hardness of the LSFT and dual phase membranes were studied at various loads. The hardness values obtained from the cross section of the membranes were also compared to that of the values obtained from the surface. An electrochemical cell has been designed and built for measurements of the Seebeck coefficient as a function of temperature and pressure. Measurements on La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-{delta}} as a function of temperature an oxygen partial pressure are reported. Further analysis of the dilatometry data obtained previously is presented. A series of isotope transients under air separation mode (small gradient) were completed on the membrane of LSCrF-2828 at 900 C. Low pO{sub 2} atmospheres based on with CO-CO{sub 2} mixtures have also been admitted to the delivery side of the LSCrF-2828 membrane to produce the gradients which exist under syngas generation conditions. The CO-CO{sub 2} mixtures have normal isotopic {sup 18}O abundances. The evolution of {sup 18}O on the delivery side in these experiments after an {sup 18}O pulse on the air side reveals a wealth of information about the oxygen transport processes.

  20. Environmental decision making: supply-chain considerations

    E-Print Network [OSTI]

    Reich-Weiser, Corinne; Dornfeld, David

    2008-01-01T23:59:59.000Z

    manufacturing environmental impact and enable the reductionthe supply chain (3) environmental impact and cost must bethe supply chain’s environmental impact and flexibility (

  1. Supplying High-Quality, Raw Biomass

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Supplying High-Quality, Raw Biomass The building blocks to supply high-quality raw biomass start with harvesting and collection practices, product storage and recommendations of...

  2. Electrocatalyst for oxygen reduction with reduced platinum oxidation and dissolution rates

    DOE Patents [OSTI]

    Adzic, Radoslav; Zhang, Junliang; Vukmirovic, Miomir

    2012-11-13T23:59:59.000Z

    The invention relates to platinum-metal oxide composite particles and their use as electrocatalysts in oxygen-reducing cathodes and fuel cells. The invention particularly relates to methods for preventing the oxidation of the platinum electrocatalyst in the cathodes of fuel cells by use of these platinum-metal oxide composite particles. The invention additionally relates to methods for producing electrical energy by supplying such a fuel cell with an oxidant, such as oxygen, and a fuel source, such as hydrogen.

  3. Electrocatalyst for oxygen reduction with reduced platinum oxidation and dissolution rates

    DOE Patents [OSTI]

    Adzic, Radoslav (East Setauket, NY); Zhang, Junliang (Stony Brook, NY); Vukmirovic, Miomir (Port Jefferson Station, NY)

    2011-11-22T23:59:59.000Z

    The invention relates to platinum-metal oxide composite particles and their use as electrocatalysts in oxygen-reducing cathodes and fuel cells. The invention particularly relates to methods for preventing the oxidation of the platinum electrocatalyst in the cathodes of fuel cells by use of these platinum-metal oxide composite particles. The invention additionally relates to methods for producing electrical energy by supplying such a fuel cell with an oxidant, such as oxygen, and a fuel source, such as hydrogen.

  4. Contiguous Platinum Monolayer Oxygen Reduction Electrocatalysts...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Contiguous Platinum Monolayer Oxygen Reduction Electrocatalysts on High-Stability-Low-Cost Supports Contiguous Platinum Monolayer Oxygen Reduction Electrocatalysts on...

  5. Stabilization of Platinum Nanoparticle Electrocatalysts for Oxygen...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Platinum Nanoparticle Electrocatalysts for Oxygen Reduction Using Poly(diallyldimethylammonium chloride). Stabilization of Platinum Nanoparticle Electrocatalysts for Oxygen...

  6. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; T. Nithyanantham

    2006-12-31T23:59:59.000Z

    Ti doping on La{sub 1-x}Sr{sub x}FeO{sub 3-{delta}} (LSF) tends to increase the oxygen equilibration kinetics of LSF in lower oxygen activity environment because of the high valence state of Ti. However, the addition of Ti decreases the total conductivity because the acceptor ([Sr{prime}{sub La}]) is compensated by the donor ([Ti{sub Fe}{sup {sm_bullet}}]) which decreases the carrier concentration. The properties of La{sub 0.2}Sr{sub 0.8}Fe{sub 1-x}Ti{sub x}O{sub 3-{delta}} (LSFT, x = 0.45) have been experimentally and theoretically investigated to elucidate (1) the dependence of oxygen occupancy and electrochemical properties on temperature and oxygen activity by thermogravimetric analysis (TGA) and (2) the electrical conductivity and carrier concentration by Seebeck coefficient and electrical measurements. In the present study, dual phase (La{sub 0.2}Sr{sub 0.8}Fe{sub 0.6}Ti{sub 0.4}O{sub 3-{delta}}/Ce{sub 0.9}Gd{sub 0.1}O{sub 2-{delta}}) membranes have been evaluated for structural properties such as hardness, fracture toughness and flexural strength. The effect of high temperature and slightly reducing atmosphere on the structural properties of the membranes was studied. The flexural strength of the membrane decreases upon exposure to slightly reducing conditions at 1000 C. The as-received and post-fractured membranes were characterized using XRD, SEM and TG-DTA to understand the fracture mechanisms. Changes in structural properties of the composite were sought to be correlated with the physiochemical features of the two-phases. We have reviewed the electrical conductivity data and stoichiometry data for La{sub 0.2}Sr{sub 0.8}Cr{sub 0.2}Fe{sub 0.8}O{sub 3-{delta}} some of which was reported previously. Electrical conductivity data for La{sub 0.2}Sr{sub 0.8}Cr{sub 0.2}Fe{sub 0.8}O{sub 3-{delta}} (LSCrF) were obtained in the temperature range, 752 {approx} 1055 C and in the pO{sub 2} range, 10{sup -18} {approx} 0.5 atm. The slope of the plot of log {sigma} vs. log pO{sub 2} is {approx} 1/5 in the p-type region, pO{sub 2} = 10{sup -5} {approx} 10{sup -1} atm. The pO{sub 2} at which the p-n transition is observed increases with increasing temperature. The activation energy for ionic conduction was estimated to be 0.86 eV from an Arrhenius plot of the minimum conductivity vs. reciprocal temperature. At temperatures below 940 C, a plateau in the conductivity isotherm suggests the presence of a two-phase region. Most likely, phase separation occurs to form a mixture of a perovskite phase and an oxygen vacancy ordered phase related to brownmillerite. Additional data for the oxygen non stoichiometry are presented.

  7. Petroleum supply monthly, July 1994

    SciTech Connect (OSTI)

    Not Available

    1994-07-26T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  8. Petroleum supply monthly, June 1994

    SciTech Connect (OSTI)

    Not Available

    1994-06-28T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  9. Petroleum supply monthly, September 1991

    SciTech Connect (OSTI)

    Not Available

    1991-09-30T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administrations for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics. 65 tabs.

  10. Petroleum supply monthly, January 1996

    SciTech Connect (OSTI)

    NONE

    1996-02-15T23:59:59.000Z

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  11. Petroleum supply monthly, August 1994

    SciTech Connect (OSTI)

    Not Available

    1994-08-26T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  12. International Oil Supplies and Demands

    SciTech Connect (OSTI)

    Not Available

    1992-04-01T23:59:59.000Z

    The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--1990 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world's dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group's thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

  13. Petroleum supply monthly, July 1993

    SciTech Connect (OSTI)

    Not Available

    1993-07-29T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: Petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  14. Petroleum Supply Monthly, May 1985

    SciTech Connect (OSTI)

    Not Available

    1985-07-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products through May, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This issue features a ''Mid-Year Petroleum Review'', beginning on page xiii and focusing on major petroleum supply developments in the first half of 1985 and the outlook for the remainder of the year. The article discusses changes in consumption, domestic crude oil production, refinery operations, foreign trade, stocks (including the Strategic Petroleum Reserve) and prices. 33 tabs.

  15. Petroleum supply monthly, July 1984

    SciTech Connect (OSTI)

    Not Available

    1984-09-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for July 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This issue also presents IEA's winter 1984-1985 distillate fuel outlook and an overview of distillate fuel oil. These articles focus on the respective roles of production, imports, and stocks in meeting distillage fuel oil demand. Regional supply patterns, especially for the East Coast are also discussed. 33 tables. (DMC)

  16. International Oil Supplies and Demands

    SciTech Connect (OSTI)

    Not Available

    1991-09-01T23:59:59.000Z

    The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--90 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world's dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group's thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

  17. Composite oxygen transport membrane

    DOE Patents [OSTI]

    Christie, Gervase Maxwell; Lane, Jonathan A.

    2014-08-05T23:59:59.000Z

    A method of producing a composite oxygen ion membrane and a composite oxygen ion membrane in which a porous fuel oxidation layer and a dense separation layer and optionally, a porous surface exchange layer are formed on a porous support from mixtures of (Ln.sub.1-xA.sub.x).sub.wCr.sub.1-yB.sub.yO.sub.3-.delta. and a doped zirconia. In the porous fuel oxidation layer and the optional porous surface exchange layer, A is Calcium and in the dense separation layer A is not Calcium and, preferably is Strontium. Preferred materials are (La.sub.0.8Ca.sub.0.2).sub.0.95Cr.sub.0.5Mn.sub.0.5O.sub.3-.delta. for the porous fuel oxidation and optional porous surface exchange layers and (La.sub.0.8Sr.sub.0.2).sub.0.95Cr.sub.0.5Fe.sub.0.5O.sub.3-.delta. for the dense separation layer. The use of such materials allows the membrane to sintered in air and without the use of pore formers to reduce membrane manufacturing costs. The use of materials, as described herein, for forming the porous layers have application for forming any type of porous structure, such as a catalyst support.

  18. Assessing Reliability in Energy Supply Systems

    E-Print Network [OSTI]

    McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

    2008-01-01T23:59:59.000Z

    total of 15 metrics. Pathway reliability General objectives Adequacy Security Functional zones Primary energy supply

  19. Assessing reliability in energy supply systems

    E-Print Network [OSTI]

    McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

    2007-01-01T23:59:59.000Z

    total of 15 metrics. Pathway reliability General objectives Adequacy Security Functional zones Primary energy supply

  20. CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR

    E-Print Network [OSTI]

    Su, Xiao

    CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR THE SEMICONDUCTOR INDUSTRY By: Yasser Dessouky #12;Carbon Footprint Supply Chain Carbon Trust defines carbon footprint of a supply chain as follows: "The carbon footprint of a product is the carbon dioxide emitted across the supply chain for a single

  1. High Selectivity Oxygen Delignification

    SciTech Connect (OSTI)

    Arthur J. Ragauskas

    2005-09-30T23:59:59.000Z

    The overall objective of this program was to develop improved extended oxygen delignification (EOD) technologies for current U.S. pulp mill operations. This was accomplished by: (1) Identifying pulping conditions that optimize O and OO performance; (2) Identifying structural features of lignin that enhance reactivity towards EOD of high kappa pulps; (3) Identifying factors minimizing carbohydrate degradation and improve pulp strength of EOD high kappa pulps; (4) Developing a simple, reproducible method of quantifying yield gains from EOD; and (5) Developing process conditions that significantly reduce the capital requirements of EOD while optimizing the yield benefits. Key research outcomes included, demonstrating the use of a mini-O sequence such as (E+O)Dkf:0.05(E+O) or Dkf:0.05(E+O)(E+O) without interstage washing could capture approximately 60% of the delignification efficiency of a conventional O-stage without the major capital requirements associated with an O-stage for conventional SW kraft pulps. The rate of formation and loss of fiber charge during an O-stage stage can be employed to maximize net fiber charge. Optimal fiber charge development and delignification are two independent parameters and do not parallel each other. It is possible to utilize an O-stage to enhance overall cellulosic fiber charge of low and high kappa SW kraft pulps which is beneficial for physical strength properties. The application of NIR and multi-variant analysis was developed into a rapid and simple method of determining the yield of pulp from an oxygen delignification stage that has real-world mill applications. A focus point of this program was the demonstration that Kraft pulping conditions and oxygen delignification of high and low-kappa SW and HW pulps are intimately related. Improved physical pulp properties and yield can be delivered by controlling the H-factor and active alkali charge. Low AA softwood kraft pulp with a kappa number 30 has an average improvement of 2% in yield and 4 cP in viscosity in comparison to high AA pulp for the oxygen delignification. This difference is also seen for high-kappa SW kraft pulps with an average improvement of {approx}3% in yield and 3 cP in viscosity for low AA high kappa number 50 pulp. Low AA hardwood kappa number 20 pulp had an average improvement of {approx}4% in yield and 6-12 cP in viscosity as compared to high AA pulp. Lower kraft cooking temperature (160 vs. 170 C) in combination with the medium AA provides a practical approach for integrating high kappa pulping of hardwoods (i.e., low rejects) with an advanced extended oxygen delignification stage. ECF pulp bleaching of low and high kappa kraft SW and HW pulps exhibit comparable optical and physical strength properties when bleached D(EPO)D.

  2. Petroleum supply monthly, January 1994

    SciTech Connect (OSTI)

    Not Available

    1994-01-01T23:59:59.000Z

    Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  3. Petroleum Supply Monthly, March 1985

    SciTech Connect (OSTI)

    Not Available

    1985-05-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for March 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. 13 figs., 33 tabs.

  4. Petroleum Supply Monthly, April 1985

    SciTech Connect (OSTI)

    Not Available

    1985-06-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products through April, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks.

  5. Petroleum Supply Monthly, October 1984

    SciTech Connect (OSTI)

    Not Available

    1984-12-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for October 1984. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administraction for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks.

  6. Optical conductivity of curved graphene

    E-Print Network [OSTI]

    A. J. Chaves; T. Frederico; O. Oliveira; W. de Paula; M. C. Santos

    2014-05-01T23:59:59.000Z

    We compute the optical conductivity for an out-of-plane deformation in graphene using an approach based on solutions of the Dirac equation in curved space. Different examples of periodic deformations along one direction translates into an enhancement of the optical conductivity peaks in the region of the far and mid infrared frequencies for periodicities $\\sim100\\,$nm. The width and position of the peaks can be changed by dialling the parameters of the deformation profiles. The enhancement of the optical conductivity is due to intraband transitions and the translational invariance breaking in the geometrically deformed background. Furthemore, we derive an analytical solution of the Dirac equation in a curved space for a general deformation along one spatial direction. For this class of geometries, it is shown that curvature induces an extra phase in the electron wave function, which can also be explored to produce interference devices of the Aharonov-Bohm type.

  7. Oxygen-reducing catalyst layer

    DOE Patents [OSTI]

    O'Brien, Dennis P. (Maplewood, MN); Schmoeckel, Alison K. (Stillwater, MN); Vernstrom, George D. (Cottage Grove, MN); Atanasoski, Radoslav (Edina, MN); Wood, Thomas E. (Stillwater, MN); Yang, Ruizhi (Halifax, CA); Easton, E. Bradley (Halifax, CA); Dahn, Jeffrey R. (Hubley, CA); O'Neill, David G. (Lake Elmo, MN)

    2011-03-22T23:59:59.000Z

    An oxygen-reducing catalyst layer, and a method of making the oxygen-reducing catalyst layer, where the oxygen-reducing catalyst layer includes a catalytic material film disposed on a substrate with the use of physical vapor deposition and thermal treatment. The catalytic material film includes a transition metal that is substantially free of platinum. At least one of the physical vapor deposition and the thermal treatment is performed in a processing environment comprising a nitrogen-containing gas.

  8. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; N. Nagabhushana; X.-D Zhou; Q. Cai; J. Yang; W.B. Yelon; W.J. James; H.U. Anderson; Alan Jacobson; C.A. Mims

    2004-05-01T23:59:59.000Z

    The present quarterly report describes some of the investigations on the structural properties of dense OTM bars provided by Praxair and studies on newer composition of Ti doped LSF. In this report, in situ neutron diffraction was used to characterize the chemical and structural properties of La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-{delta}} (here after as L2SF55T) specimen, which was subject to measurements of neutron diffraction from room temperature to 900 C. It was found that space group of R3c yielded a better refinement than a cubic structure of Pm3m. Oxygen occupancy was nearly 3 in the region from room temperature to 700 C, above which the occupancy decreased due to oxygen loss. Dense OTM bars provided by Praxair were loaded to fracture at varying stress rates. Studies were done at room temperature in air and at 1000 C in a specified environment to evaluate slow crack growth behavior. The X-Ray data and fracture mechanisms points to non-equilibrium decomposition of the LSFCO OTM membrane. The non-equilibrium conditions could probably be due to the nature of the applied stress field (stressing rates) and leads to transition in crystal structures and increased kinetics of decomposition. The formations of a Brownmillerite or Sr2Fe2O5 type structures, which are orthorhombic are attributed to the ordering of oxygen vacancies. The cubic to orthorhombic transitions leads to 2.6% increase in strains and thus residual stresses generated could influence the fracture behavior of the OTM membrane. Continued investigations on the thermodynamic properties (stability and phase-separation behavior) and total conductivity of prototype membrane materials were carried out. The data are needed together with the kinetic information to develop a complete model for the membrane transport. Previously characterization, stoichiometry and conductivity measurements for samples of La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-{delta}} were reported. In this report, measurements of the chemical and thermal expansion as a function of temperature and p{sub O2} are described.

  9. Electrochemical studies of quinone oxygen

    SciTech Connect (OSTI)

    Deanhardt, M.L. (Lander College, Greenwood, SC (US)); Mushrush, G.W.; Stalick, W.M. (Chemistry Dept., George mason Univ., Fairfax, VA (US)); Watkins, J.M. Jr. (Naval Research Lab., Fuels Section, Code 6180, Washington, DC (US))

    1990-02-01T23:59:59.000Z

    Asphaltenes are a chemically complex mixture of aromatic and heteroaromatic compounds. This material contains oxygen in various functional groups. The distribution includes esters, carboxylic acids, phenolic and most probably quinone type oxygen functionalities. The present work details the complete electrochemical behaviour of quinone type oxygen. The method is quinone specific. A condensed aromatic quinone, 9,10-anthraquinone, was selected as representative of complex quinones. By this method quinones can be determined in the presence of other oxygen functional groups, alcohols, carboxylic acids, ethers, and other carbonyls.

  10. Improved climate forecast accuracy: implications for the aggregate sorghum supply curve

    E-Print Network [OSTI]

    Hill, Harvey S. J.

    1995-01-01T23:59:59.000Z

    of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE Approved as to style and content by: James W. Mjelde (Chair of Committee) ey D. Rosenthal (Member) Stephen W. Fuller (Member) A. Gene Nelson... AND CONCLUSIONS 59 by Event, Site and Price . . 65 67 84 90 90 95 99 Conclusions Limitations and Recommendations for Further Study 100 104 REFERENCES APPENDIX A APPENDIX B 108 119 121 APPENDIX C . . APPENDIX D . . )58 177 VITA . 196 LIST...

  11. Sixth Northwest Conservation and Electric Power Plan Appendix E: Conservation Supply Curve

    E-Print Network [OSTI]

    ....................................................................................................... 11 Value of Energy Saved ......................................................................................................................... 17 Residential Sector Definition and Coverage........................................................................................................................ 22 Commercial Sector Definition and Coverage

  12. Investigating the variation in CO[subscript 2] sequestration supply curves

    E-Print Network [OSTI]

    House, Kurt Zenz

    CCS projects that can bring together all pieces of the system—capture, transport, and storage—at the lowest cost will likely be the first to become operational. We have modeled the cost per tonne of CO[subscript 2] of a ...

  13. 2009 Geothermal, Co-Production, and GSHP Supply Curves | Department of

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartment ofCBFO-13-3322 2013of EnergyFourth Annual Report January

  14. Estimating Carbon Supply Curves for Global Forests and Other Land Uses |

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualPropertyd8c-a9ae-f8521cbb8489 No revision|LLCInsulation IncentivesEshone EnergyEstero,

  15. Document Supply Services Quick Guide

    E-Print Network [OSTI]

    , phrase, ISBN/ISSN in the Search Term field (other options are available in the dropdown menu). Note1 Document Supply Services Quick Guide The DSS Portal makes requesting easy! Search for your item and password. If you are having difficulty please read the login help on the main DSS webpage. 2. Enter a word

  16. Fastbus Power Supply Manual University of Washington Seattle, 26 March, 1996 Fastbus Power Supplies

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    supplies each have their own built­in cooling fans, and the lower­current supplies are sufficiently cooledFastbus Power Supply Manual University of Washington Seattle, 26 March, 1996 page 1 Fastbus Power Supplies HGB, 03/26/1996 Overview Each of the four Fastbus crates of the SuperK OD DAQ system is supplied

  17. Petroleum supply monthly, March 1994

    SciTech Connect (OSTI)

    Not Available

    1994-03-30T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

  18. Petroleum supply monthly, June 1993

    SciTech Connect (OSTI)

    Not Available

    1993-06-28T23:59:59.000Z

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures ih the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas - - the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided firom other sources.

  19. Harmonic algebraic curves and noncrossing partitions

    E-Print Network [OSTI]

    Martin, Jeremy L.; Savitt, David; Singer, Ted

    2007-02-01T23:59:59.000Z

    Motivated by Gauss’s first proof of the fundamental Theorem of Algebra, we study the topology of harmonic algebraic curves. By the maximum principle, a harmonic curve has no bounded components; its topology is determined by the combinatorial data...

  20. Explicit Coleman integration for hyperelliptic curves

    E-Print Network [OSTI]

    Balakrishnan, Jennifer S; Kedlaya, Kiran S

    2010-01-01T23:59:59.000Z

    Coleman's theory of p-adic integration figures prominently in several number-theoretic applications, such as finding torsion and rational points on curves, and computing p-adic regulators in K-theory (including p-adic heights on elliptic curves). We describe an algorithm for computing Coleman integrals on hyperelliptic curves, and its implementation in Sage.

  1. Multipath Curved Planar Reformation of the Peripheral

    E-Print Network [OSTI]

    Multipath Curved Planar Reformation of the Peripheral Arterial Tree in CT Angiography1 Justus that cause artifacts in multipath curved planar reformations (MPCPRs) of the peripheral arterial tree in 10-oblique multiplanar reformations perpendicular to the ves- sel centerline (10), and curved planar reformations

  2. Oxygen detection using evanescent fields

    DOE Patents [OSTI]

    Duan, Yixiang (Los Alamos, NM); Cao, Weenqing (Los Alamos, NM)

    2007-08-28T23:59:59.000Z

    An apparatus and method for the detection of oxygen using optical fiber based evanescent light absorption. Methylene blue was immobilized using a sol-gel process on a portion of the exterior surface of an optical fiber for which the cladding has been removed, thereby forming an optical oxygen sensor. When light is directed through the optical fiber, transmitted light intensity varies as a result of changes in the absorption of evanescent light by the methylene blue in response to the oxygen concentration to which the sensor is exposed. The sensor was found to have a linear response to oxygen concentration on a semi-logarithmic scale within the oxygen concentration range between 0.6% and 20.9%, a response time and a recovery time of about 3 s, ant to exhibit good reversibility and repeatability. An increase in temperature from 21.degree. C. to 35.degree. C. does not affect the net absorption of the sensor.

  3. Gravitational-wave sensitivity curves

    E-Print Network [OSTI]

    Moore, C. J.; Cole, R. H.; Berry, C. P. L.

    2014-12-08T23:59:59.000Z

    the detectability of a given source (see figure A1). An additional advantage of this convention is that the values on the strain axis for the detector curve hn(f) have a simple physical interpretation: they correspond to the root-mean- square noise in a bandwidth f... , such as cryogenic cooling. The Einstein Telescope (ET) is an ambitious proposal to construct an underground third- generation detector. Its location would provide shielding from seismic noise, allowing it to observe frequencies of ?(10 10 )Hz4 . We use...

  4. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; N. Nagabhushana; X.-D Zhou; Q. Cai; J. Yang; W.B. Yelon; W.J. James; H.U. Anderson; Alan Jacobson; C.A. Mims

    2004-10-01T23:59:59.000Z

    The present quarterly report describes some of the investigations on the structural properties of dense OTM bars provided by Praxair and studies on newer composition of Ti doped LSF. In this report, Moessbauer spectroscopy was used to study the local environmentals of LSFT with various level of oxygen deficiency. Ionic valence state, magnetic interaction and influence of Ti on superexchange are discussed Stable crack growth studies on Dense OTM bars provided by Praxair were done at elevated temperature, pressure and elevated conditions. Post-fracture X-ray data of the OTM fractured at 1000 C in environment were refined by FullProf code and results indicate a distortion of the parent cubic perovskite to orthorhombic structure with reduced symmetry. TGA-DTA studies on the post-fracture samples also indicated residual effect arising from the thermal and stress history of the samples. An electrochemical cell has been designed and built for measurements of the Seebeck coefficient as a function of temperature and pressure. The initial measurements on La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-{delta}} are reported. Neutron diffraction measurements of the same composition are in agreement with both the stoichiometry and the kinetic behavior observed in coulometric titration measurements. A series of isotope transients under air separation mode (small gradient) were completed on the membrane of LSCrF-2828 at 900 C. Low pO{sub 2} atmospheres based on with CO-CO{sub 2} mixtures have also been admitted to the delivery side of the LSCrF-2828 membrane to produce the gradients which exist under syngas generation conditions. The COCO{sub 2} mixtures have normal isotopic {sup 18}O abundances. The evolution of {sup 18}O on the delivery side in these experiments after an {sup 18}O pulse on the air side reveals a wealth of information about the oxygen transport processes.

  5. Low Oxygen Environments in Chesapeake Bay

    E-Print Network [OSTI]

    Boynton, Walter R.

    Low Oxygen Environments in Chesapeake Bay Jeremy Testa Chesapeake Biological Laboratory University of Maryland Center for Environmental Science Why we care about low oxygen? What causes low oxygen? Where and When does Chesapeake Bay lose oxygen? #12;#12;Hypoxia and Chesapeake Animals Low dissolved oxygen

  6. Mixed oxygen ion/electron-conducting ceramics for oxygen separation

    SciTech Connect (OSTI)

    Stevenson, J.W.; Armstrong, B.L.; Armstrong, T.R.; Bates, J.L.; Pederson, L.R.; Weber, W.J.

    1995-05-01T23:59:59.000Z

    Solid mixed-conducting electrolytes in the series La{sub l-x}A{sub x}Co{sub l-y}Fe{sub y}O{sub 3-{delta}} (A = Sr,Ca,Ba) are potentially useful as passive membranes to separate high purity oxygen from air and as cathodes in fuel cells. All of the compositions studied exhibited very high electrical conductivities. At lower temperatures, conductivities increased with increasing temperature, characterized by activation energies of 0.05 to 0.16 eV that are consistent with a small polaron (localized electronic carrier) conduction mechanism. At higher temperatures, electronic conductivities tended to decrease with increasing temperature, which is attributed to decreased electronic carrier populations associated with lattice oxygen loss. Oxygen ion conductivities were higher than that of yttria stabilized zirconia and increased with the cobalt content and also increased with the extent of divalent A-site substitution. Thermogravimetric studies were conducted to establish the extent of oxygen vacancy formation as a function of temperature, oxygen partial pressure, and composition. These vacancy populations strongly depend on the extent of A-site substitution. Passive oxygen permeation rates were established for each of the compositions as a function of temperature and oxygen partial pressure gradient. For 2.5 mm thick membranes in an oxygen vs nitrogen partial pressure gradient, oxygen fluxes at 900 C ranged from approximately 0.3 sccm/cm{sup 2} for compositions high in iron and with low amounts of strontium A-site substitution to approximately 0.8 sccm/cm{sup 2} for compositions high in cobalt and strontium. A-site substitution with calcium instead of strontium resulted in substantially lower fluxes.

  7. Petroluem Supply Monthly, May 1993

    SciTech Connect (OSTI)

    Not Available

    1993-06-04T23:59:59.000Z

    Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  8. Petroleum Supply Monthly, November 1984

    SciTech Connect (OSTI)

    Not Available

    1985-01-28T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for November 1984. Information on crude oil, gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Summary statistics include data from 1973 to 1984. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude oil, net receipts, crude losses, refinery inputs, exports, products supplied,and ending stocks. The focus article, US Petroleum Developments - - 1984., summarizes changes in consumption, refinery operations, petroleum stocks, imports, production and prices. The article includes an update on refinery closings.

  9. Petroleum Supply Monthly, January 1985

    SciTech Connect (OSTI)

    Not Available

    1985-03-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for January, 1985. Information on crude oil, finished motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases are included. Detailed statistics show production for the current month as well as the year-to-date. Data are also tabulated for the US Petroleum Administration for Defense (PAD) Districts which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. This month's issue features Trends in Petroleum Product Consumption. This article describes the changing patterns of US petroleum product consumption in recent years, for the major projects and by end-use sectors.

  10. Petroleum Supply Monthly, December 1984

    SciTech Connect (OSTI)

    Not Available

    1985-02-01T23:59:59.000Z

    This report contains detailed statistics on the supply and disposition of petroleum and petroleum products for December 1984. Information on crude oil, gasoline, distillate fuel oil, residual fuel oil, and liquefied petroleum gases are included. Summary statistics include data from 1973 through January 1985. Detailed statistics show production for the current month as well as the year-to-date. Data are also tubulated for the US Petroleum Administration for Defense (PAD) District which include field production, refinery production, imports, stock withdrawal or addition, unaccounted for crude oil, net receipts, crude losses, refinery inputs, exports, products supplied, and ending stocks. The featured article, US Petroleum Import/Export Trends, highlights 1984 activities and discusses historical US trade patterns for crude oil and petroleum products. 12 figures, 33 tables.

  11. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, Thomas F. (Batavia, IL)

    1989-01-01T23:59:59.000Z

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

  12. Petroleum Supply Monthly, July 1990

    SciTech Connect (OSTI)

    Not Available

    1990-09-28T23:59:59.000Z

    Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  13. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, T.F.

    1989-12-19T23:59:59.000Z

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

  14. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; N. Nagabhushana; X.-D Zhou; W.B. Yelon; H.U. Anderson; Alan Jacobson; C.A. Mims

    2004-02-01T23:59:59.000Z

    The present quarterly report describes some of the investigations on the structural properties of dense OTM bars provided by Praxair and initial studies on newer composition of Ti doped LSF. Dense OTM bars provided by Praxair were loaded to fracture at varying stress rates. Studies were done at room temperature in air and at 1000 C in a specified environment to evaluate slow crack growth behavior. In addition, studies were also begun to obtain reliable estimates of fracture toughness and stable crack growth in specific environments. Newer composition of Ti doped LSF membranes were characterized by neutron diffraction analysis. Quench studies indicated an apparent correlation between the unit cell volume and oxygen occupancy. The studies however, indicated an anomaly of increasing Fe/Ti ratio with change in heat treatment. Ti doped LSF was also characterized for stoichiometry as a function of temp and pO{sub 2}. The non stoichiometry parameter {delta} was observed to increase almost linearly on lowering pO{sub 2} until a ideal stoichiometric composition of {delta} = 0.175 was approached.

  15. Cover and startup gas supply system for solid oxide fuel cell generator

    DOE Patents [OSTI]

    Singh, P.; George, R.A.

    1999-07-27T23:59:59.000Z

    A cover and startup gas supply system for a solid oxide fuel cell power generator is disclosed. Hydrocarbon fuel, such as natural gas or diesel fuel, and oxygen-containing gas are supplied to a burner. Combustion gas exiting the burner is cooled prior to delivery to the solid oxide fuel cell. The system mixes the combusted hydrocarbon fuel constituents with hydrogen which is preferably stored in solid form to obtain a non-explosive gas mixture. The system may be used to provide both non-explosive cover gas and hydrogen-rich startup gas to the fuel cell. 4 figs.

  16. Cover and startup gas supply system for solid oxide fuel cell generator

    DOE Patents [OSTI]

    Singh, Prabhakar (Export, PA); George, Raymond A. (Pittsburgh, PA)

    1999-01-01T23:59:59.000Z

    A cover and startup gas supply system for a solid oxide fuel cell power generator is disclosed. Hydrocarbon fuel, such as natural gas or diesel fuel, and oxygen-containing gas are supplied to a burner. Combustion gas exiting the burner is cooled prior to delivery to the solid oxide fuel cell. The system mixes the combusted hydrocarbon fuel constituents with hydrogen which is preferably stored in solid form to obtain a non-explosive gas mixture. The system may be used to provide both non-explosive cover gas and hydrogen-rich startup gas to the fuel cell.

  17. Does the Environmental Kuznets Curve Describe How Individual Countries Behave?

    E-Print Network [OSTI]

    Deacon, Robert; Norman, Catherine S

    2004-01-01T23:59:59.000Z

    for an Environmental Kuznets Curve. ” Review of EconomicsFactoring the Environmental Kuznets Curve: Evidence fromand Development: Is There a Kuznets Curve for Air Pollution

  18. Is the environmental Kuznets curve an empirical regularity?

    E-Print Network [OSTI]

    Deacon, Robert; Norman, Catherine S

    2004-01-01T23:59:59.000Z

    the Environmental Kuznets Curve: Turning a Black Box into aand Development: Is There a Kuznets Curve for Air Pollutionon the Environmental Kuznets Curve? ” Environment and

  19. Coupling Renewable Energy Supply with Deferrable Demand

    E-Print Network [OSTI]

    Papavasiliou, Anthony

    2011-01-01T23:59:59.000Z

    The lattice model of renewable power supply and real-timerenewable power supply, by formulating a unit commitment model.model that can be used for assessing the impact of integrating renewable power

  20. Charlotte Green Supply Chain: Residential Retrofitting | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Charlotte Green Supply Chain: Residential Retrofitting Charlotte Green Supply Chain: Residential Retrofitting July 30, 2010 - 10:50am Addthis Joshua DeLung What does this mean for...

  1. An integrative framework for architecting supply chains

    E-Print Network [OSTI]

    Cela Díaz, Fernando

    2006-01-01T23:59:59.000Z

    This thesis explores the limitations of classic models of supply chain management, and proposes a new view based on the concept of value-driven supply chains, and a method of analysis and design based on the concepts of ...

  2. Supply chain management in the cement industry

    E-Print Network [OSTI]

    Agudelo, Isabel

    2009-01-01T23:59:59.000Z

    Traditionally supply chain management has played an operational role within cement and mineral extraction commodity companies. Recently, cost reduction projects have brought supply chain management into the limelight. In ...

  3. Loss of coordination in competitive supply chains

    E-Print Network [OSTI]

    Teo, Koon Soon

    2009-01-01T23:59:59.000Z

    The loss of coordination in supply chains quantifies the inefficiency (i.e. the loss of total profit) due to the presence of competition in the supply chain. In this thesis, we discuss four models: one model with multiple ...

  4. OXYGEN DIFFUSION IN UO2-x

    E-Print Network [OSTI]

    Kim, K.C.

    2013-01-01T23:59:59.000Z

    ~ K.C. K:i.m, "Oxygen Diffusion in Hypostoichiometricsystem for enriching uo 2 in oxygen-18 or for stoichiometry+nal of Nuclear Materials OXYGEN DIFFUSION IN U0 2 _:x K.C.

  5. Oxygen transfer in the implant environment

    E-Print Network [OSTI]

    Goor, Jared Braden

    2007-01-01T23:59:59.000Z

    Temperature dependence of oxygen diffusion and consumptionRN. Influence of temperature on oxygen diffusion in hamster341-347, 1988. Cox ME. Oxygen Diffusion in Poly(dimethyl

  6. Agents on the Web Supply Chains

    E-Print Network [OSTI]

    Almor, Amit

    Agents on the Web Automating Supply Chains 90 JULY · AUGUST 2001 http://computer.org/internet/ 1089

  7. Covered Product Category: Uninterruptible Power Supplies (for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Applications) Covered Product Category: Uninterruptible Power Supplies (for Data Center, Computer, and Telecommunication Applications) The Federal Energy Management...

  8. Coupling Renewable Energy Supply with Deferrable Demand

    E-Print Network [OSTI]

    Papavasiliou, Anthony

    2011-01-01T23:59:59.000Z

    Scale Renewable Energy Integration . . . . . . . . . . .Impacts of Renewable Energy Supply . . . . . . . . . . . . .1.3 Coupling Renewable Energy with Deferrable

  9. PRIMARY RESEARCH PAPER Water column oxygen demand and sediment oxygen flux

    E-Print Network [OSTI]

    Mallin, Michael

    PRIMARY RESEARCH PAPER Water column oxygen demand and sediment oxygen flux: patterns of oxygen dissolved oxygen (DO) levels often occur during summer in tidal creeks along the southeastern coast of the USA. We analyzed rates of oxygen loss as water-column biochemical oxygen demand (BOD5) and sediment

  10. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; N. Nagabhushana

    2003-08-07T23:59:59.000Z

    In the present quarter, experiments are presented on ceramic/metal interactions of Zirconia/ Ni-B-Si system and with a thin Ti coating deposited on zirconia surface. Existing facilities were modified for evaluation of environmental assisted slow crack growth and creep in flexural mode. Processing of perovskites of LSC, LSF and LSCF composition were continued for evaluation of mechanical properties as a function of environment. These studies in parallel to those on the LSFCO composition is expect to yield important information on questions such as the role of cation segregation and the stability of the perovskite structure on crack initiation vs. crack growth. Studies have been continued on the La{sub 1-x}Sr{sub x}FeO{sub 3-d} composition using neutron diffraction and TGA studies. A transition from p-type to n-type of conductor was observed at relative low pO{sub 2}, at which the majority carriers changed from the holes to electrons because of the valence state decreases in Fe due to the further loss of oxygen. Investigation on the thermodynamic properties of the membrane materials are continued to develop a complete model for the membrane transport. Data obtained at 850 C show that the stoichiometry in La{sub 0.2}Sr{sub 0.8}Fe{sub 0.8}Cr{sub 0.2}O{sub 3-x} vary from {approx}2.85 to 2.6 over the pressure range studied. From the stoichiometry a lower limit of 2.6 corresponding to the reduction of all Fe{sup 4+} to Fe{sup 3+} and no reduction of Cr{sup 3+} is expected.

  11. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; T. Nithyanantham; X.-D Zhou; Y-W. Sin; H.U. Anderson; Alan Jacobson; C.A. Mims

    2005-11-01T23:59:59.000Z

    The present quarterly report describes some of the investigations on the structural properties of dense OTM bars provided by Praxair and studies on newer composition of Ti doped LSF. In the current research, the electrical conductivity and Seebeck coefficient were measured as a function of temperature in air. Based on these measurements, the charge carrier concentration, net acceptor dopant concentration, activation energy of conduction and mobility were estimated. The studies on the fracture toughness of the LSFT and dual phase membranes at room temperature have been completed and reported previously. The membranes that are exposed to high temperatures at an inert and a reactive atmosphere undergo many structural and chemical changes which affects the mechanical properties. To study the effect of temperature on the membranes when exposed to an inert environment, the membranes (LAFT and Dual phase) were heat treated at 1000 C in air and N{sub 2} atmosphere and hardness and fracture toughness of the membranes were studied after the treatment. The indentation method was used to find the fracture toughness and the effect of the heat treatment on the mechanical properties of the membranes. Further results on the investigation of the origin of the slow kinetics on reduction of ferrites have been obtained. The slow kinetics appears to be related to a non-equilibrium reduction pathway that initially results in the formation of iron particles. At long times, equilibrium can be reestablished with recovery of the perovskite phase. 2-D modeling of oxygen movement has been undertaken in order to fit isotope data. The model will serve to study ''frozen'' profiles in patterned or composite membranes.

  12. High-temperature potentiometric oxygen sensor with internal reference

    DOE Patents [OSTI]

    Routbort, Jules L. (Hinsdale, IL); Singh, Dileep (Naperville, IL); Dutta, Prabir K. (Worthington, OH); Ramasamy, Ramamoorthy (North Royalton, OH); Spirig, John V. (Columbus, OH); Akbar, Sheikh (Hilliard, OH)

    2011-11-15T23:59:59.000Z

    A compact oxygen sensor is provided, comprising a mixture of metal and metal oxide an enclosure containing said mixture, said enclosure capable of isolating said mixture from an environment external of said enclosure, and a first wire having a first end residing within the enclosure and having a second end exposed to the environment. Also provided is a method for the fabrication of an oxygen sensor, the method comprising confining a metal-metal oxide solid mixture to a container which consists of a single material permeable to oxygen ions, supplying an electrical conductor having a first end and a second end, whereby the first end resides inside the container as a reference (PO.sub.2).sup.ref, and the second end resides outside the container in the atmosphere where oxygen partial pressure (PO.sub.2).sup.ext is to be measured, and sealing the container with additional single material such that grain boundary sliding occurs between grains of the single material and grains of the additional single material.

  13. Supply Chain and Information Sciences Technology 2010

    E-Print Network [OSTI]

    Guiltinan, Mark

    Supply Chain and Information Sciences Technology 2010 Supply Chain and Information Systems Technology Minor SCIST Minor Application Department of Supply Chain & Information Systems College of Information Sciences and Technology Overview The minor in SCIST is structured to provide students not majoring

  14. Extracorporeal membrane oxygenation promotes long chain fatty...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    membrane oxygenation promotes long chain fatty acid oxidation in the immature swine heart in vivo. Extracorporeal membrane oxygenation promotes long chain fatty acid oxidation...

  15. Electrocatalytic Reactivity for Oxygen Reduction of Palladium...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reactivity for Oxygen Reduction of Palladium-Modified Carbon Nanotubes Synthesized in Supercritical Fluid. Electrocatalytic Reactivity for Oxygen Reduction of Palladium-Modified...

  16. OXYGEN DIFFUSION IN HYPOSTOICHIOMETRIC URANIUM DIOXIDE

    E-Print Network [OSTI]

    Kim, Kee Chul

    2010-01-01T23:59:59.000Z

    Research Division OXYGEN DIFFUSION IN HYPOSTOICHIOMETRIC11905 -DISCLAIMER - OXYGEN DIFFUSION IN HYPOSTOICHIOMETRICc o n e e n i g woroxygen self-diffusion coefficient

  17. Formation, characterization and reactivity of adsorbed oxygen...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Formation, characterization and reactivity of adsorbed oxygen on BaOPt(111). Formation, characterization and reactivity of adsorbed oxygen on BaOPt(111). Abstract: The formation...

  18. Angling chromium to let oxygen through | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Angling chromium to let oxygen through Angling chromium to let oxygen through Released: September 10, 2014 New semiconducting material works at lower temperatures Scanning...

  19. Polycyclic Aromatic Triptycenes: Oxygen Substitution Cyclization Strategies

    E-Print Network [OSTI]

    VanVeller, Brett

    The cyclization and planarization of polycyclic aromatic hydrocarbons with concomitant oxygen substitution was achieved through acid catalyzed transetherification and oxygen-radical reactions. The triptycene scaffold ...

  20. Low energy consumption method for separating gaseous mixtures and in particular for medium purity oxygen production

    DOE Patents [OSTI]

    Jujasz, Albert J. (North Olmsted, OH); Burkhart, James A. (Olmsted Falls, OH); Greenberg, Ralph (New York, NY)

    1988-01-01T23:59:59.000Z

    A method for the separation of gaseous mixtures such as air and for producing medium purity oxygen, comprising compressing the gaseous mixture in a first compressor to about 3.9-4.1 atmospheres pressure, passing said compressed gaseous mixture in heat exchange relationship with sub-ambient temperature gaseous nitrogen, dividing the cooled, pressurized gaseous mixture into first and second streams, introducing the first stream into the high pressure chamber of a double rectification column, separating the gaseous mixture in the rectification column into a liquid oxygen-enriched stream and a gaseous nitrogen stream and supplying the gaseous nitrogen stream for cooling the compressed gaseous mixture, removing the liquid oxygen-enriched stream from the low pressure chamber of the rectification column and pumping the liquid, oxygen-enriched steam to a predetermined pressure, cooling the second stream, condensing the cooled second stream and evaporating the oxygen-enriched stream in an evaporator-condenser, delivering the condensed second stream to the high pressure chamber of the rectification column, and heating the oxygen-enriched stream and blending the oxygen-enriched stream with a compressed blend-air stream to the desired oxygen concentration.

  1. A lithium oxygen secondary battery

    SciTech Connect (OSTI)

    Semkow, K.W.; Sammells, A.F.

    1987-08-01T23:59:59.000Z

    In principle the lithium-oxygen couple should provide one of the highest energy densities yet investigated for advanced battery systems. The problem to this time has been one of identifying strategies for achieving high electrochemical reversibilities at each electrode under conditions where one might anticipate to also achieve long materials lifetimes. This has been addressed in recent work by us via the application of stabilized zirconia oxygen vacancy conducting solid electrolytes, for the effective separation of respective half-cell reactions.

  2. Petroleum supply monthly: December 1993

    SciTech Connect (OSTI)

    Not Available

    1993-12-01T23:59:59.000Z

    Data are presented which describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. Data are presented in two sections: Summary Statistics, presenting a time series of selected petroleum data on a U.S. level, and Detailed Statistics, presenting statistics for the most current month available as well as year to date.

  3. Supply Stores | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you wantJoin us for|Idaho |Energy Supercomputers: ExtremeSupply

  4. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; N. Nagabhushana; Thomas W. Eagar; Harold R. Larson; Raymundo Arroyave; X.-D Zhou; Y.-W. Shin; H.U. Anderson; Nigel Browning; Alan Jacobson; C.A. Mims

    2003-11-01T23:59:59.000Z

    The present quarterly report describes some of the initial studies on newer compositions and also includes newer approaches to address various materials issues such as in metal-ceramic sealing. The current quarter's research has also focused on developing a comprehensive reliability model for predicting the structural behavior of the membranes in realistic conditions. In parallel to industry provided compositions, models membranes have been evaluated in varying environment. Of importance is the behavior of flaws and generation of new flaws aiding in fracture. Fracture mechanics parameters such as crack tip stresses are generated to characterize the influence of environment. Room temperature slow crack growth studies have also been initiated in industry provided compositions. The electrical conductivity and defect chemistry of an A site deficient compound (La{sub 0.55}Sr{sub 0.35}FeO{sub 3}) was studied. A higher conductivity was observed for La{sub 0.55}Sr{sub 0.35}FeO{sub 3} than that of La{sub 0.60}Sr{sub 0.40}FeO{sub 3} and La{sub 0.80}Sr{sub 0.20}FeO{sub 3}. Defect chemistry analysis showed that it was primarily contributed by a higher carrier concentration in La{sub 0.55}Sr{sub 0.35}FeO{sub 3}. Moreover, the ability for oxygen vacancy generation is much higher in La{sub 0.55}Sr{sub 0.35}FeO{sub 3} as well, which indicates a lower bonding strength between Fe-O and a possible higher catalytic activity for La{sub 0.55}Sr{sub 0.35}FeO{sub 3}. The program continued to investigate the thermodynamic properties (stability and phase separation behavior) and total conductivity of prototype membrane materials. The data are needed together with the kinetic information to develop a complete model for the membrane transport. Previous report listed initial measurements on a sample of La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-x} prepared in-house by Praxair. Subsequently, a second sample of powder from a larger batch of sample were characterized and compared with the results from the previous batch.

  5. UV Light Curves of Thermonuclear Supernovae

    E-Print Network [OSTI]

    S. I. Blinnikov; E. I. Sorokina

    2000-03-17T23:59:59.000Z

    Ultraviolet light curves are calculated for several thermonuclear supernova models using a multifrequency radiation hydrodynamic code. It is found that Chandrasekhar-mass models produce very similar light curves both for detonation and deflagration. Sub-Chandrasekhar-mass models essentially differ from ``normal'' Chandrasekhar ones regarding behaviour of their UV fluxes. Differences in absolute brightness and in shape of light curves of thermonuclear supernovae could be detectable up to 300 Mpc with modern UV space telescopes.

  6. Optimization of Supply Chain Management and Facility Location Selection for a Biorefinery

    E-Print Network [OSTI]

    Bowling, Ian Michael

    2012-02-14T23:59:59.000Z

    Figure 7. United States Gross Domestic Product Growth (World Bank, 2010) 1.5 Government Incentives for Biofuels In early 2010 the United States President announced several initiatives geared towards encouraging the use of renewable liquid fuels... location and transportation costs. The model was used to develop a reasonable biofuel supply curve for the western United States. The model considered three modes of transportation; truck, rail and barge. Ek?ioglu et. al. (2009) developed a model...

  7. Natural Gas Supply SBIR Program

    SciTech Connect (OSTI)

    Shoemaker, H.D.; Gwilliam, W.J.

    1995-07-01T23:59:59.000Z

    The Small Business Innovation Research (SBIR) program was created in 1982 by Public Law 97-219 and reauthorized in 1992 until the year 2000 by Public Law 102-564. The purposes of the new law are to (1) expand and improve the SBIR program, 2) emphasize the program`s goal of increasing private sector commercialization of technology developed through Federal R&D, (3) increase small business participation in Federal R&D, and (4) improve the Federal Government`s dissemination of information concerning the SBIR program. DOE`s SBIR pro-ram has two features that are unique. In the 1995 DOE SBIR solicitation, the DOE Fossil Energy topics were: environmental technology for natural gas, oil, and coal; advanced recovery of oil; natural gas supply; natural gas utilization; advanced coal-based power systems; and advanced fossil fuels research. The subtopics for this solicitation`s Natural Gas Supply topic are (1) drilling, completion, and stimulation; (2) low-permeability Formations; (3) delivery and storage; and (4) natural gas upgrading.

  8. Learning Curve - DOE Directives, Delegations, and Requirements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    This chapter discusses the development and application of the learning curve. g4301-1chp21.pdf -- PDF Document, 28 KB Writer: John Makepeace Subjects: Administration Management...

  9. Canonical correlation of shipping forward curves

    E-Print Network [OSTI]

    Hadjiyiannis, Nicholas

    2010-01-01T23:59:59.000Z

    The behavior and interrelations between the main shipping forward curves are analyzed using multivariate statistics after removing the volatility distortions dictated by the Samuelson hypothesis. Principal Components ...

  10. Oxygen Transport Ceramic Membranes

    SciTech Connect (OSTI)

    S. Bandopadhyay; N. Nagabhushana; X.-D Zhou; Q. Cai; J. Yang; W.B. Yelon; W.J. James; H.U. Anderson; Alan Jacobson; C.A. Mims

    2004-05-01T23:59:59.000Z

    The present quarterly report describes some of the investigations on the structural properties of dense OTM bars provided by Praxair and studies on newer composition of Ti doped LSF. In this report, in situ neutron diffraction was used to characterize the chemical and structural properties of La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-{delta}} (here after as L2SF55T) specimen, which was subject to measurements of neutron diffraction from room temperature to 900 C in N{sub 2}. Space group of R3c was found to result in a better refinement and is used in this study. The difference for crystal structure, lattice parameters and local crystal chemistry for LSFT nearly unchanged when gas environment switched from air to N{sub 2}. Stable crack growth studies on Dense OTM bars provided by Praxair were done at room temperature in air. A bridge-compression fixture was fabricated to achieve stable pre-cracks from Vickers indents. Post fracture evaluation indicated stable crack growth from the indent and a regime of fast fracture. Post-fracture X-ray data of the OTM fractured at 1000 C in environment were refined by FullProf code and results indicate a distortion of the parent cubic perovskite to orthorhombic structure with reduced symmetry. TGA-DTA studies on the post-fracture samples also indicated residual effect arising from the thermal and stress history of the samples. The thermal and chemical expansion of La{sub 0.2}Sr{sub 0.8}Fe{sub 0.55}Ti{sub 0.45}O{sub 3-{delta}} were studied at 800 {le} T {le} 1000 C and at {approx} 1 x 10{sup -15} {le} pO{sub 2} {le} 0.21 atm. The thermal expansion coefficient of the sample was calculated from the dilatometric analysis in the temperature range between room temperature and 1200 C in air. A series of isotope transients under air separation mode (small gradient) were completed on the membrane of LSCrF-2828 at 900 C. Low pO{sub 2} atmospheres based on with CO-CO{sub 2} mixtures have also been admitted to the delivery side of the LSCrF-2828 membrane to produce the gradients which exist under syngas generation conditions. The CO-CO{sub 2} mixtures have normal isotopic {sup 18}O abundances. The evolution of {sup 18}O on the delivery side in these experiments after an {sup 18}O pulse on the air side reveals a wealth of information about the oxygen transport processes.

  11. OXYGEN ADSORPTION ON NITROGEN CONTAINING CARBON SURFACES

    E-Print Network [OSTI]

    Truong, Thanh N.

    OXYGEN ADSORPTION ON NITROGEN CONTAINING CARBON SURFACES Alejandro Montoya, Jorge O. Gil, Fanor-rich site of the carbon basal plane of graphite and then, it dissociates into oxygen atoms.1,2 Oxygen atoms at the edge of the carbon surface can form covalent bonds with oxygen. These sites can chemisorb

  12. Eliminating oxygen supply limitations for transplanted microencapsulated islets in the treatment of type 1 diabetes

    E-Print Network [OSTI]

    Lewis, Amy Suzanne

    2008-01-01T23:59:59.000Z

    Type I diabetes is a disease that results from a person's impaired ability to produce insulin, a protein that regulates the blood glucose concentration. Insulin is produced by [beta]-cells in the Islets of Langerhans, which ...

  13. D0 Detector Assemble Hall Platform Oxygen Deficiency Hazard Analysis

    SciTech Connect (OSTI)

    Clark, D.; Michael, J.; /Fermilab

    1991-01-29T23:59:59.000Z

    Liquid cryogens, released and warming to atmosphere conditions, expand to, on average, seven hundred times their liquid volume, and displace vital atmospheric oxygen. An oxygen deficiency hazard analysis assesses the increased risk to personnel in areas containing cryogenic systems. The D0 detector platform area ODH analysis has been approached four different ways using established methods. In each case, the analysis shows the platform area to be ODH class 0 as equipped (with ventilation fans) and requiring no special safety provisions. System designers have provided for a reduced oxygen level detection and warning system as well as emergency procedures to address fault conditions. The Oxygen Deficiency Hazard of any particular area is defined by these parameters: the nature of the accidental supply of inert gas (probability of occurrence and quantity then released), the area's volume, the area's ventilation rate, and to a small degree the elevation of the area. Once this information is assembled, the ODH classification can be determined through standardized calculations. The platform area under the D0 detector contains much of the cryogenic and gas system piping necessary for the D0 experiment. Prior to moving the detector into the Collision Hall, the liquid argon calorimeters are cooled down and operated in the Assembly Hall. The first phase of this operation involved the cooldown of the Central Calorimeter, which was done in February 1991. This engineering note assesses the increased risk to personnel in the platform level to a reduced oxygen atmosphere during the cool down and subsequent operation of the calorimeters in the Assembly Hall. In addition, it outlines the steps taken to warn personnel of an emergency and to direct the subsequent evacuation. This note analyses only the Assembly Hall area. A similar engineering note, EN-332, covers the analysis of the Collision Hall area.

  14. Uninterruptible power supply (UPS) systems

    SciTech Connect (OSTI)

    NONE

    1997-04-01T23:59:59.000Z

    Use of this purchase specification is not mandatory. User should review the document and determine if it meets the user`s purpose. This document contains a fill-in-the-blanks guide specification for the procurement of uninterruptible power supply (UPS) systems greater than 10 kVA, organized as follows: Parts 1 through 7--technical requirements; Appendix A--technical requirements to be included in the proposal; Appendix B--UPS system data sheets to be completed by each bidder (Seller) and submitted with the proposal; Appendix C--general guidelines giving the specifier parameters for selecting a UPS system; it should be read before preparing an actual specification, and is not attached to the specification; Attachment 1--sketches prepared by the purchaser (Owner); Attachment 2--sample title page.

  15. Projection-based curve clustering Benjamin AUDER

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    -hydraulic computer code CATHARE is used to study the re- liability of reactor vessels. The code inputs are physical parameters and the outputs are time evolution curves of a few other physical quantities. As the CATHARE code process involves a clustering step. In the present paper, CATHARE output curves are clustered using a k

  16. Oxygen isotopic exchange: A useful tool for characterizing oxygen conducting oxides

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Oxygen isotopic exchange: A useful tool for characterizing oxygen conducting oxides Bassat J we obtain in both cases data concerning the oxygen diffusion in the bulk and the oxygen exchange with regards to the oxygen reduction reaction. Detailed experimental and analytical processes are given

  17. Petroleum supply annual 1995: Volume 1

    SciTech Connect (OSTI)

    NONE

    1996-05-01T23:59:59.000Z

    The {ital Petroleum Supply Annual} contains information on supply and disposition of crude oil and petroleum products. It reflects data collected from the petroleum industry during 1995 through monthly surveys, and it is divided into 2 volumes. This volume contains three sections: summary statistics, detailed statistics, and selected refinery statistics, each with final annual data. (The other volume contains final statistics for each month and replaces data previously published in the {ital Petroleum Supply Monthly}).

  18. Shock-activated electrochemical power supplies

    DOE Patents [OSTI]

    Benedick, W.B.; Graham, R.A.; Morosin, B.

    1988-11-08T23:59:59.000Z

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolytes rendering the electrolyte electrochemically active. 2 figs.

  19. Shock-activated electrochemical power supplies

    DOE Patents [OSTI]

    Benedick, W.B.; Graham, R.A.; Morosin, B.

    1987-04-20T23:59:59.000Z

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolyte rendering the electrolyte electrochemically active. 2 figs.

  20. Experiments on oxygen desorption from surface warm seawater under open-cycle ocean thermal energy conversion (OC-OTEC) conditions

    SciTech Connect (OSTI)

    Pesaran, A.A.

    1989-12-01T23:59:59.000Z

    This paper reports the results of scoping deaeration experiments conducted with warm surface seawater under open-cycle ocean thermal energy conversion (OC-OTEC). Concentrations of dissolved oxygen in seawater at three locations (in the supply water, water leaving a predeaerator, and discharge water from an evaporator) were measured and used to estimate oxygen desorption levels. The results suggest that 7% to 60% of dissolved oxygen in the supply water was desorbed from seawater in the predeaerator for pressures ranging from 9 to 35 kPa. Bubble injection in the upcomer increased the oxygen desorption rate by 20% to 60%. The dependence of oxygen desorption with flow rate could not be determined. The data also indicated that at typical OC-OTEC evaporator pressures when flashing occurred, 75% to 95% of dissolved oxygen was desorbed overall from the warm seawater. The uncertainty in results is larger than one would desire. These uncertainties are attributed to the uncertainties and difficulties in the dissolved oxygen measurements. Methods to improve the measurements for future gas desorption studies for warm surface and cold deep seawater under OC-OTEC conditions are recommended. 14 refs., 5 figs., 2 tabs.

  1. Oxygen uptake of benthic systems

    E-Print Network [OSTI]

    Priebe, William Franklin

    1972-01-01T23:59:59.000Z

    mg/hr/sq m between standard and maximum mixing. Hanes and Irvine (23) made a determination of the effects of temperature on quiescent oxygen uptake rates by covering sludge with aerated water and allowing the supernatant to be totally de- pleted.... ECTROLTSIS STSTDI FOA MEMURIRC BOO. FIGURE 2. SWITCH ELECTROQE IN CONTACT WITH ELECTROIYTE. OXYGEN GENERATOR OFF. FIGURE 3. SWIICH ELECI'RODE NOT IN CONTACT' WITH -' ECTROLYTE. 0 0 0 a 0 0 0 ~ O0 0 o 0 0 o o 0 0 0 0 PIERRE A. HIGH SPEED NIXINC...

  2. Oxygen uptake of benthic systems 

    E-Print Network [OSTI]

    Priebe, William Franklin

    1972-01-01T23:59:59.000Z

    mg/hr/sq m between standard and maximum mixing. Hanes and Irvine (23) made a determination of the effects of temperature on quiescent oxygen uptake rates by covering sludge with aerated water and allowing the supernatant to be totally de- pleted.... ECTROLTSIS STSTDI FOA MEMURIRC BOO. FIGURE 2. SWITCH ELECTROQE IN CONTACT WITH ELECTROIYTE. OXYGEN GENERATOR OFF. FIGURE 3. SWIICH ELECI'RODE NOT IN CONTACT' WITH -' ECTROLYTE. 0 0 0 a 0 0 0 ~ O0 0 o 0 0 o o 0 0 0 0 PIERRE A. HIGH SPEED NIXINC...

  3. Coupling Renewable Energy Supply with Deferrable Demand

    E-Print Network [OSTI]

    Papavasiliou, Anthony

    2011-01-01T23:59:59.000Z

    order: cost comparison for the deep-simple, zero wind,expected wind supply, instead of averaging the cost savingsintegration of wind power. Cost, Utilization, Investment

  4. Coupling Renewable Energy Supply with Deferrable Demand

    E-Print Network [OSTI]

    Papavasiliou, Anthony

    2011-01-01T23:59:59.000Z

    systems absorb large amounts of hydroelectric power. Duringthat snow melts and hydroelectric power supply increases andfrom hydroelectric dams or discards renewable power [53].

  5. GI Self-Supply Pilot Overview

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BPA TRANSMISSION SERVICES Transmission Wind Integration Systems Team GENERATION IMBALANCE SELF SUPPLY PILOT PROJECT OVERVIEW VERSION: 0.1 UPDATED: 7292009 giself-supplypilotov...

  6. Assessing reliability in energy supply systems

    E-Print Network [OSTI]

    McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

    2007-01-01T23:59:59.000Z

    pathway supplying hydrogen via pipeline from a centralizedgas with pipeline distribution of hydrogen, and 2) on-sitehydrogen is transported to the refueling stations via pipeline

  7. Assessing Reliability in Energy Supply Systems

    E-Print Network [OSTI]

    McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

    2008-01-01T23:59:59.000Z

    pathway supplying hydrogen via pipeline from a centralizedgas with pipeline distribution of hydrogen, and 2) on-sitehydrogen is transported to the refueling stations via pipeline

  8. Assessing reliability in energy supply systems

    E-Print Network [OSTI]

    McCarthy, Ryan W.; Ogden, Joan M.; Sperling, Daniel

    2007-01-01T23:59:59.000Z

    liquefied natural gas (LNG) trading expected to increase insteam reformation production facility using imported LNG.The LNG supplies come primarily from Trinidad and Tobago,

  9. Assessing Reliability in Energy Supply Systems

    E-Print Network [OSTI]

    McCarthy, Ryan; Ogden, Joan M.; Sperling, Dan

    2008-01-01T23:59:59.000Z

    liquefied natural gas (LNG) trading expected to increase insteam reformation production facility using imported LNG.The LNG supplies come primarily from Trinidad and Tobago,

  10. Advanced Accessory Power Supply Topologies

    SciTech Connect (OSTI)

    Marlino, L.D.

    2010-06-15T23:59:59.000Z

    This Cooperative Research and Development Agreement (CRADA) began December 8, 2000 and ended September 30, 2009. The total funding provided by the Participant (General Motors Advanced Technology Vehicles [GM]) during the course of the CRADA totaled $1.2M enabling the Contractor (UT-Battelle, LLC [Oak Ridge National Laboratory, a.k.a. ORNL]) to contribute significantly to the joint project. The initial task was to work with GM on the feasibility of developing their conceptual approach of modifying major components of the existing traction inverter/drive to develop low cost, robust, accessory power. Two alternate methods for implementation were suggested by ORNL and both were proven successful through simulations and then extensive testing of prototypes designed and fabricated during the project. This validated the GM overall concept. Moreover, three joint U.S. patents were issued and subsequently licensed by GM. After successfully fulfilling the initial objective, the direction and duration of the CRADA was modified and GM provided funding for two additional tasks. The first new task was to provide the basic development for implementing a cascaded inverter technology into hybrid vehicles (including plug-in hybrid, fuel cell, and electric). The second new task was to continue the basic development for implementing inverter and converter topologies and new technology assessments for hybrid vehicle applications. Additionally, this task was to address the use of high temperature components in drive systems. Under this CRADA, ORNL conducted further research based on GM’s idea of using the motor magnetic core and windings to produce bidirectional accessory power supply that is nongalvanically coupled to the terminals of the high voltage dc-link battery of hybrid vehicles. In order not to interfere with the motor’s torque, ORNL suggested to use the zero-sequence, highfrequency harmonics carried by the main fundamental motor current for producing the accessory power. Two studies were conducted at ORNL. One was to put an additional winding in the motor slots to magnetically link with the high frequency of the controllable zero-sequence stator currents that do not produce any zero-sequence harmonic torques. The second approach was to utilize the corners of the square stator punching for the high-frequency transformers of the dc/dc inverter. Both approaches were successful. This CRADA validated the feasibility of GM’s desire to use the motor’s magnetic core and windings to produce bidirectional accessory power supply. Three joint U.S. patents with GM were issued to ORNL and GM by the U.S. Patent Office for the research results produced by this CRADA.

  11. Gauge Invariant Geometry of Closed Space Curves: Applications to Boundary Curves of Mobius-type Strips

    E-Print Network [OSTI]

    Radha Balakrishnan; Indubala I Satija

    2005-07-15T23:59:59.000Z

    We derive gauge-invariant expressions for the twist $Tw$ and the linking number $Lk$ of a closed space curve, that are independent of the frame used to describe the curve, and hence characterize the intrinsic geometry of the curve. We are thus led to a {\\it frame-independent} version of the C\\u{a}lug\\u{a}reanu-White-Fuller theorem $Lk =Tw + Wr$ for a curve, where $Wr$ is the writhe of the curve. The gauge-invariant twist and writhe are related to two types of geometric phases associated with the curve. As an application, we study the geometry of the boundary curves of closed twisted strips. Interestingly, the M\\"obius strip geometry is singled out by a characteristic maximum that appears in the geometric phases, at a certain critical width of the strip.

  12. Certified Professional in Supply Management (CPSM) Review Series: Exam 2: Effective Supply Management Performance

    E-Print Network [OSTI]

    · Materials and Inventory Management · Organization/Department Assessment · Planning · Product and ServiceCertified Professional in Supply Management (CPSM) Review Series: Exam 2: Effective Supply Management Performance Dates: October 28, 2011 Location: Rutgers University­ Livingston Campus, Tillett Hall

  13. Energy-efficient uninterruptible power supplies and switchmode power supplies for office technology

    SciTech Connect (OSTI)

    Eyer, J.

    1995-12-01T23:59:59.000Z

    There are three aspects of energy performance. The first is efficiency, and it specifically affects fuel use and the amount of emissions produced in relation to the amount of energy used and the fuel mix used in generation plants. Heat is rejected into the space with the result being additional air-conditioning to remove the heat. This often affects the capacity of the air-conditioning system. Customer electric bills are higher when more energy is used. The next important aspect of energy performance is peak electric demand. The capital requirements that utilities must put in place to deliver power to the customer affect many decisions made about energy efficiency and reduction of energy use. The capital requirements comprise 70 to 80% of the cost of delivering electricity to customers, while the fuel and variable costs associated with actually generating electricity are relatively small-20 to 30% of the total costs. In many respects, demand-side management programs are focused on reducing the need for increased capital equipment. Another aspect of energy performance is power quality. This is an important ally issue that could be addressed with initiatives similar to those for energy efficiency. Most power quality problems are related to current harmonics. Electronic equipment commonly reflects current harmonics back into the system, producing significant effects on the capacity of the system to deliver power. Immunity to poor power quality may be the most important aspect in receiving the benefits of improved power quality and power-conditioned equipment. Immunity is defined by the Computer and Business Equipment Manufacturers Association curve, which defines how `robust` the power supply must be with particular respect to low voltages. The immunity to different power quality problems could be dramatically improved by using existing technologies.

  14. Protective supplied breathing air garment

    DOE Patents [OSTI]

    Childers, E.L.; Hortenau, E.F. von.

    1984-07-10T23:59:59.000Z

    A breathing air garment is disclosed for isolating a wearer from hostile environments containing toxins or irritants includes a suit and a separate head protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit rear torso panel permits access into the suit and is sealed with an adhesive sealing flap. 17 figs.

  15. Lead -- supply/demand outlook

    SciTech Connect (OSTI)

    Schnull, T. [Noranda, Inc., Toronto, Ontario (Canada)

    1999-03-01T23:59:59.000Z

    As Japan goes--so goes the world. That was the title of a recent lead article in The Economist that soberly discussed the potential of much more severe global economic problems occurring, if rapid and coordinated efforts were not made to stabilize the economic situation in Asia in general, and in Japan in particular. During the first 6 months of last year, commodity markets reacted violently to the spreading economic problems in Asia. More recent currency and financial problems in Russia have exacerbated an already unpleasant situation. One commodity after another--including oil, many of the agricultural commodities, and each of the base metals--have dropped sharply in price. Many are now trading at multiyear lows. Until there is an overall improvement in the outlook for these regions, sentiment will likely continue to be negative, and metals prices will remain under pressure. That being said, lead has maintained its value better than many other commodities during these difficult times, finding support in relatively strong fundamentals. The author takes a closer look at those supply and demand fundamentals, beginning with consumption.

  16. E951 POWER SUPPLY SAFETY REVIEW

    E-Print Network [OSTI]

    McDonald, Kirk

    E951 POWER SUPPLY SAFETY REVIEW 9/06/02 IOANNIS MARNERIS Brookhaven National Labs. #12;Project. · To do this we will use 4 existing SCR type dc power supplies from the experimental area in series 3644 Voltage (V) 150 300 300 Peakcurrent (A) 3600 7200 7200 Field (T) 5.0 10.0 14.5 Inductance (mH) 138

  17. SUMMER 2007 ELECTRICITY SUPPLY AND DEMAND OUTLOOK

    E-Print Network [OSTI]

    CALIFORNIA ENERGY COMMISSION SUMMER 2007 ELECTRICITY SUPPLY AND DEMAND OUTLOOK DRAFTSTAFFREPORT May ELECTRICITY ANALYSIS OFFICE Sylvia Bender Acting Deputy Director ELECTRICITY SUPPLY ANALYSIS DIVISION B. B assessment of the capability of the physical electricity system to provide power to meet electricity demand

  18. Biomass Supply and Carbon Accounting for

    E-Print Network [OSTI]

    Biomass Supply and Carbon Accounting for Southeastern Forests February 2012 #12;This Biomass Supply and Carbon Accounting for Southeastern Forests study was conducted by the Biomass Energy Resource Center Biomass Energy Resource Center Kamalesh Doshi Biomass Energy Resource Center Hillary Emick Biomass Energy

  19. EXOTIC OPTIONS FOR INTERRUPTIBLE ELECTRICITY SUPPLY CONTRACTS

    E-Print Network [OSTI]

    with different strike prices. Such options allow hedging and valuation of supply curtailment risk, while demand side participation in the mitigation of supply shortages for energy and reserves. Newly curtailment can provide an efficient substitute for generation capacity in providing balancing energy

  20. Proposal for the Cryogenic Supply of a

    E-Print Network [OSTI]

    1 Proposal for the Cryogenic Supply of a Single TTF / FEL - Cryomodule Test Bench TESLA Report No supply are described. 1. Introduction For the time being, TTF- cryomodules can only be cold tested after will change. The quadrupoles will be cooled in the 2.0 K liquid bath instead by the 4.5K cooling circuit

  1. Transportation Energy: Supply, Demand and the Future

    E-Print Network [OSTI]

    Saldin, Dilano

    Transportation Energy: Supply, Demand and the Future http://www.uwm.edu/Dept/CUTS//2050/energy05 as a source of energy. Global supply and demand trends will have a profound impact on the ability to use our) Transportation energy demand in the U.S. has increased because of the greater use of less fuel efficient vehicles

  2. A Supply Chain Network Perspective for Electric

    E-Print Network [OSTI]

    Nagurney, Anna

    of New Models "[In recent years] the adequacy of the bulk power transmission system has been challengedA Supply Chain Network Perspective for Electric Power Generation, Supply, Transmission The transformation of the electric power industry from a regulated to a competitive industry In the US, In the EU

  3. Optimal Trading Strategy Supply/Demand Dynamics

    E-Print Network [OSTI]

    Gabrieli, John

    prices through the changes in their supply/demand.2 Thus, to study how market participants trade can have interesting implications on the observed behavior of intraday volume, volatility and prices: November 15, 2004. This Draft: April 8, 2006 Abstract The supply/demand of a security in the market

  4. Supply Chain Management Faculty Brian Fugate

    E-Print Network [OSTI]

    University. He has worked in materials management professionally for over 10 years with high tech electronicsSupply Chain Management Faculty Brian Fugate Brian S. Fugate (Ph.D University of Tennessee) is an Associate Professor of Supply Chain Management at Colorado State University. Brian worked in logistics

  5. A Supply Chain Network Perspective for Electric Power Generation, Supply, Transmission, and Consumption

    E-Print Network [OSTI]

    Nagurney, Anna

    A Supply Chain Network Perspective for Electric Power Generation, Supply, Transmission, and Consumption Anna Nagurney and Dmytro Matsypura Department of Finance and Operations Management Isenberg School, Berlin, Germany, pp. 3-27. Abstract: A supply chain network perspective for electric power production

  6. Supply Chain Networks, Electronic Commerce, and Supply Side and Demand Side Risk

    E-Print Network [OSTI]

    Nagurney, Anna

    Supply Chain Networks, Electronic Commerce, and Supply Side and Demand Side Risk Anna Nagurney as well as demand side risk are included in the formulation. The model consists of three tiers of decision chain network equilibrium model with electronic com- merce and with supply side and demand side risk

  7. Certified Professional in Supply Management (CPSM) & Certified in Supply Management (CSM) Exam Preparation Series

    E-Print Network [OSTI]

    Lin, Xiaodong

    -Taking Hints and Tips Exam 2 Content Forecasting Logistics Materials and Inventory Management OrganizationCertified Professional in Supply Management (CPSM) & Certified in Supply Management (CSM) Exam for member companies of the Rutgers Center for Supply Chain Management. $425 for non-members This one day

  8. Classification and forecasting of load curves Nolwen Huet

    E-Print Network [OSTI]

    Cuesta, Juan Antonio

    Classification and forecasting of load curves Nolwen Huet Abstract The load curve, which gives of electricity customer uses. This load curve is only available for customers with automated meter reading. For the others, EDF must estimate this curve. Usually a clustering of the load curves is performed, followed

  9. Coal slurry fuel supply and purge system

    DOE Patents [OSTI]

    McDowell, Robert E. (Fairview, PA); Basic, Steven L. (Hornell, NY); Smith, Russel M. (North East, PA)

    1994-01-01T23:59:59.000Z

    A coal slurry fuel supply and purge system for a locomotive engines is disclosed which includes a slurry recirculation path, a stand-by path for circulating slurry during idle or states of the engine when slurry fuel in not required by the engine, and an engine header fluid path connected to the stand-by path, for supplying and purging slurry fuel to and from fuel injectors. A controller controls the actuation of valves to facilitate supply and purge of slurry to and from the fuel injectors. A method for supplying and purging coal slurry in a compression ignition engine is disclosed which includes controlling fluid flow devices and valves in a plurality of fluid paths to facilitate continuous slurry recirculation and supply and purge of or slurry based on the operating state of the engine.

  10. Diffusion-Limited Aggregation on Curved Surfaces

    E-Print Network [OSTI]

    Choi, J.

    We develop a general theory of transport-limited aggregation phenomena occurring on curved surfaces, based on stochastic iterated conformal maps and conformal projections to the complex plane. To illustrate the theory, we ...

  11. Learning Curve Management in Educational Programming Environments

    E-Print Network [OSTI]

    Goldman, Kenneth J.

    Learning Curve Management in Educational Programming Environments Benjamin H. Brinckerhoff Computer programmers are best served by integrated development environments that adapt to their growing sophistication programming environments. We provide pedagogical justification for each goal, describe possible supporting

  12. Methods for separating oxygen from oxygen-containing gases

    DOE Patents [OSTI]

    Mackay, Richard (Lafayette, CO); Schwartz, Michael (Boulder, CO); Sammells, Anthony F. (Boulder, CO)

    2000-01-01T23:59:59.000Z

    This invention provides mixed conducting metal oxides particularly useful for the manufacture of catalytic membranes for gas-phase oxygen separation processes. The materials of this invention have the general formula: A.sub.x A'.sub.x A".sub.2-(x+x') B.sub.y B'.sub.y B".sub.2-(y+y') O.sub.5+z ; where x and x' are greater than 0; y and y' are greater than 0; x+x' is less than or equal to 2; y+y' is less than or equal to 2; z is a number that makes the metal oxide charge neutral; A is an element selected from the f block lanthanide elements; A' is an element selected from Be, Mg, Ca, Sr, Ba and Ra; A" is an element selected from the f block lanthanides or Be, Mg, Ca, Sr, Ba and Ra; B is an element selected from the group consisting of Al, Ga, In or mixtures thereof; and B' and B" are different elements and are independently selected from the group of elements Mg or the d-block transition elements. The invention also provides methods for oxygen separation and oxygen enrichment of oxygen deficient gases which employ mixed conducting metal oxides of the above formula. Examples of the materials used for the preparation of the membrane include A.sub.x Sr.sub.x' B.sub.y Fe.sub.y' Co.sub.2-(y+y') O.sub.5+z, where x is about 0.3 to about 0.5, x' is about 1.5 to about 1.7, y is 0.6, y' is between about 1.0 and 1.4 and B is Ga or Al.

  13. Wavelet Analysis of Galactic Rotation Curves

    E-Print Network [OSTI]

    M. Kuassivi

    2011-04-28T23:59:59.000Z

    The spatial wavelet spectra of 73 published spiral galaxies's rotation curves are computed and their associated scaleograms are presented. Scaleograms are used to detect and isolate local features observed in spiral galaxies's rotation curves. Although wiggles and bumps are usually interpreted as signs of recent and on-going merging, the analysis of the scaleograms reveals regular patterns consistent with the presence of large-scale modes throughout the disk.

  14. Chiral gap effect in curved space

    E-Print Network [OSTI]

    Antonino Flachi; Kenji Fukushima

    2014-06-25T23:59:59.000Z

    We discuss a new type of QCD phenomenon induced in curved space. In the QCD vacuum a mass gap of Dirac fermions is attributed to the spontaneous breaking of chiral symmetry. If the curvature is positive large, the chiral condensate melts but a chiral invariant mass gap can still remain, which we name the chiral gap effect in curved space. This leads to decoupling of quark deconfinement which implies a view of black holes surrounded by a first-order QCD phase transition.

  15. Oxygen reduction on platinum : an EIS study

    E-Print Network [OSTI]

    Golfinopoulos, Theodore

    2009-01-01T23:59:59.000Z

    The oxygen reduction reaction (ORR) on platinum over yttria-stabilized zirconia (YSZ) is examined via electrochemical impedance spectroscopy (EIS) for oxygen partial pressures between 10-4 and 1 atm and at temperatures ...

  16. Microbial oceanography of anoxic oxygen minimum zones

    E-Print Network [OSTI]

    Ulloa, Osvaldo

    Vast expanses of oxygen-deficient and nitrite-rich water define the major oxygen minimum zones (OMZs) of the global ocean. They support diverse microbial communities that influence the nitrogen economy of the oceans, ...

  17. Microchemical systems for singlet oxygen generation

    E-Print Network [OSTI]

    Hill, Tyrone F. (Tyrone Frank), 1980-

    2008-01-01T23:59:59.000Z

    Chemical Oxygen-Iodine Lasers (COIL) are a technology of interest for industrial and military audiences. COILs are flowing gas lasers where the gain medium of iodine atoms is collisionally pumped by singlet delta oxygen ...

  18. Mitochondrial reactive oxygen species and cancer

    E-Print Network [OSTI]

    Chandel, Navdeep S

    Mitochondria produce reactive oxygen species (mROS) as a natural by-product of electron transport chain activity. While initial studies focused on the damaging effects of reactive oxygen species, a recent paradigm shift ...

  19. Imaging Oxygen Molecules Up Close | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Imaging Oxygen Molecules Up Close Imaging Oxygen Molecules Up Close Released: March 20, 2011 ARRA-enabled upgrades enhance research capabilities STM images of the same TiO2(110)...

  20. Environmental bias and elastic curves on surfaces

    E-Print Network [OSTI]

    Jemal Guven; Dulce María Valencia; Pablo Vázquez-Montejo

    2014-08-15T23:59:59.000Z

    The behavior of an elastic curve bound to a surface will reflect the geometry of its environment. This may occur in an obvious way: the curve may deform freely along directions tangent to the surface, but not along the surface normal. However, even if the energy itself is symmetric in the curve's geodesic and normal curvatures, which control these modes, very distinct roles are played by the two. If the elastic curve binds preferentially on one side, or is itself assembled on the surface, not only would one expect the bending moduli associated with the two modes to differ, binding along specific directions, reflected in spontaneous values of these curvatures, may be favored. The shape equations describing the equilibrium states of a surface curve described by an elastic energy accommodating environmental factors will be identified by adapting the method of Lagrange multipliers to the Darboux frame associated with the curve. The forces transmitted to the surface along the surface normal will be determined. Features associated with a number of different energies, both of physical relevance and of mathematical interest, are described. The conservation laws associated with trajectories on surface geometries exhibiting continuous symmetries are also examined.

  1. The Mechanisms of Oxygen Reduction and Evolution Reactions in...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Mechanisms of Oxygen Reduction and Evolution Reactions in Nonaqueous Lithium-Oxygen Batteries. The Mechanisms of Oxygen Reduction and Evolution Reactions in Nonaqueous...

  2. Composite oxygen ion transport element

    DOE Patents [OSTI]

    Chen, Jack C. (Getzville, NY); Besecker, Charles J. (Batavia, IL); Chen, Hancun (Williamsville, NY); Robinson, Earil T. (Mentor, OH)

    2007-06-12T23:59:59.000Z

    A composite oxygen ion transport element that has a layered structure formed by a dense layer to transport oxygen ions and electrons and a porous support layer to provide mechanical support. The dense layer can be formed of a mixture of a mixed conductor, an ionic conductor, and a metal. The porous support layer can be fabricated from an oxide dispersion strengthened metal, a metal-reinforced intermetallic alloy, a boron-doped Mo.sub.5Si.sub.3-based intermetallic alloy or combinations thereof. The support layer can be provided with a network of non-interconnected pores and each of said pores communicates between opposite surfaces of said support layer. Such a support layer can be advantageously employed to reduce diffusion resistance in any type of element, including those using a different material makeup than that outlined above.

  3. Catalyst containing oxygen transport membrane

    DOE Patents [OSTI]

    Christie, Gervase Maxwell; Wilson, Jamie Robyn; van Hassel, Bart Antonie

    2012-12-04T23:59:59.000Z

    A composite oxygen transport membrane having a dense layer, a porous support layer and an intermediate porous layer located between the dense layer and the porous support layer. Both the dense layer and the intermediate porous layer are formed from an ionic conductive material to conduct oxygen ions and an electrically conductive material to conduct electrons. The porous support layer has a high permeability, high porosity, and a high average pore diameter and the intermediate porous layer has a lower permeability and lower pore diameter than the porous support layer. Catalyst particles selected to promote oxidation of a combustible substance are located in the intermediate porous layer and in the porous support adjacent to the intermediate porous layer. The catalyst particles can be formed by wicking a solution of catalyst precursors through the porous support toward the intermediate porous layer.

  4. Effects of oxygen on fracturing fluids

    SciTech Connect (OSTI)

    Walker, M.L.; Shuchart, C.E.; Yaritz, J.G.; Norman, L.R.

    1995-11-01T23:59:59.000Z

    The stability of polysaccharide gels at high temperature is limited by such factors as pH, mechanical degradation, and oxidants. Oxygen is unavoidably placed in fracturing fluids through dissolution of air. To prevent premature degradation of the fracturing fluid by this oxidant, oxygen scavengers are commonly used. In this paper, the effects of oxygen and various oxygen scavengers on gel stability will be presented. Mechanical removal of oxygen resulted in surprisingly stable fracturing gels at 275 F. However, chemical removal of oxygen gave mixed results. Test data from sodium thiosulfate, sodium sulfite, and sodium erythorbate used as oxygen scavengers/gel stabilizers showed that the efficiency of oxygen removal from gels did not directly coincide with the viscosity retention of the gel, and large excesses of additives were necessary to provide optimum gel stabilization. The inability of some oxygen scavengers to stabilize the gel was the result of products created from the interaction of oxygen with the oxygen scavenger, which in turn, produced species that degraded the gel. The ideal oxygen scavenger should provide superior gel stabilization without creating detrimental side reaction products. Of the materials tested, sodium thiosulfate appeared to be the most beneficial.

  5. Oxygen Detection via Nanoscale Optical Indicators

    E-Print Network [OSTI]

    Ghosh, Ruby N.

    Oxygen Detection via Nanoscale Optical Indicators Ruby N. Ghosh Dept. of Physics Michigan State University East Lansing, MI, USA weekschr@msu.edu Abstract--Oxygen plays a ubiquitous role in terrestrial developed an optical technique for monitoring oxygen in both gas and liquid phases utilizing nanoscale metal

  6. 8, 22252248, 2008 Detection of oxygen

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    ACPD 8, 2225­2248, 2008 Detection of oxygen emission related to spring bloom H. Yamagishi et al Chemistry and Physics Discussions Detection of regional scale sea-to-air oxygen emission related to spring bloom near Japan by using in-situ measurements of atmospheric oxygen/nitrogen ratio H. Yamagishi 1 , Y

  7. CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR THE

    E-Print Network [OSTI]

    Su, Xiao

    CALCULATING THE CARBON FOOTPRINT SUPPLY CHAIN FOR THE SEMICONDUCTOR INDUSTRY A LEARNING TOOL By a complete supply chain #12;Carbon Footprint Supply Chain Carbon Trust defines carbon footprint of a supply chain as follows: "The carbon footprint of a product is the carbon dioxide emitted across the supply

  8. Petroleum supply annual, 1997. Volume 1

    SciTech Connect (OSTI)

    NONE

    1998-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. 16 figs., 48 tabs.

  9. CONCEPTUAL DESIGN STUDY OF HORN POWER SUPPLY.

    SciTech Connect (OSTI)

    ZHANG,W.; SANDBERG,J.; WENG,W.T.

    2003-06-16T23:59:59.000Z

    A 250 kA pulsed power supply is required for the focusing horn of the proposed Brookhaven AGS Super Neutrino Beam Facility for long baseline neutrino oscillation experiment. It is expected to pulse at 2.5 Hz repetition rate. A preliminary study is being conducted to explore the key issues associated with the power supply system design. Advanced technologies used in similar systems as well as new ideas are being examined, simulated and evaluated. This power supply will be a very high stored energy, high average power, and high peak power system.

  10. Electrospray characteristic curves: in pursuit of improved performance...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electrospray characteristic curves: in pursuit of improved performance in the nano-flow regime. Electrospray characteristic curves: in pursuit of improved performance in the...

  11. Oxygen permeation in bismuth-based materials part I: Sintering and oxygen permeation fluxes

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Oxygen permeation in bismuth-based materials part I: Sintering and oxygen permeation fluxes E;2 Abstract Oxygen permeation measurements were performed on two layered bismuth based oxide ceramics. Oxygen permeability for these systems was compared to permeability of the cubic fluorite type structure

  12. Singlet Oxygen Singlet oxygen generation and detection are growing fields with applications in such areas as

    E-Print Network [OSTI]

    Wells, Mathew G. - Department of Physical and Environmental Sciences, University of Toronto

    Singlet Oxygen Singlet oxygen generation and detection are growing fields with applications in such areas as cancer treatment, photosensitized oxidations, and biomolecular degradation. Ground state oxygen state of an oxygen molecule is a singlet state, which can readily react with other singlet molecules

  13. Lycopene cyclase paralog CruP protects against reactive oxygen species in oxygenic

    E-Print Network [OSTI]

    Wurtzel, Eleanore

    , quenching singlet oxygen generated during the water-splitting process of photo- synthesis (10, 11). VariousLycopene cyclase paralog CruP protects against reactive oxygen species in oxygenic photosynthetic cyclase. Instead, we show that CruP aids in preventing accumulation of reactive oxygen species (ROS

  14. Experimental Effects of Atomic Oxygen on the Development of an Electric Discharge Oxygen Iodine Laser

    E-Print Network [OSTI]

    Carroll, David L.

    state I. Conventionally, a two-phase (gas-liquid) chemistry singlet oxygen generator (SOG) producesExperimental Effects of Atomic Oxygen on the Development of an Electric Discharge Oxygen Iodine of the electric discharge iodine laser continues, the role of oxygen atoms downstream of the discharge region

  15. Freedom from Pollution? The State, the People, and the Environmental Kuznets Curve

    E-Print Network [OSTI]

    Bond, Craig A.; Farzin, Y. Hossein

    2004-01-01T23:59:59.000Z

    and the environmental Kuznets curve for deforestation: aand the environmental Kuznets curve. Ecological Economicsbias in environmental Kuznets curves. Ecological Economics

  16. Segmentation strategies for managing retail supply chains

    E-Print Network [OSTI]

    Liang, Catherine G. (Catherine Gloria)

    2011-01-01T23:59:59.000Z

    High-technology manufacturing companies often face rapid price decline and capacity constraints. Especially in the retail side of the business where the supply chain is much longer and revenue is sometimes not recognized ...

  17. Handling Food and Supplies during Power Loss

    E-Print Network [OSTI]

    Anding, Jenna

    2005-09-30T23:59:59.000Z

    This publication lists foods that are safe to eat without cooking or refrigeration. There is also a list of supplies you will need when gas and electrical service is unavailable....

  18. Advanced Supply System Validation Workshop Agenda

    Broader source: Energy.gov [DOE]

    List of Assumptions and Draft Workshop Agenda for the Advanced Supply System Validation Workshop, February 3-4, 2014, Golden, Colorado, from the U.S. Department of Energy's Bioenergy Technologies Office.

  19. Supply chain practices in the petroleum downstream

    E-Print Network [OSTI]

    Santos Manzano, Fidel

    2005-01-01T23:59:59.000Z

    This thesis studies current supply chain practices in the petroleum downstream industry, using ExxonMobil as a case study. Based on the analysis of the literature and the interaction with industry experts, this work describes ...

  20. Essays on Married Women Labor Supply

    E-Print Network [OSTI]

    Li, Xinrong

    2012-02-14T23:59:59.000Z

    One of the very interesting demographic features in the US over the last three decades of the 20th century is the increase of the married women labor force participation rate. Over the same period, estimated labor supply elasticity varies...

  1. An analysis of oil supply disruption scenarios

    E-Print Network [OSTI]

    Mork, Knut Anton

    1981-01-01T23:59:59.000Z

    This report brings the results of simulations of some oil supply disruptions on the M.I.T. Energy Laboratory Energy Macro Model. This model has previously been used to study the macroeconomic effects of the 1973-74 and ...

  2. Polynomial policies in supply chain networks

    E-Print Network [OSTI]

    He, Liwei

    2010-01-01T23:59:59.000Z

    This thesis aims to solve the periodic-reviewed inventory control problem in supply chain networks with uncertain demand so as to minimize the overall cost of the system over a fixed planning time horizon. In such problems, ...

  3. Returning Home After a Disaster: Supply List

    E-Print Network [OSTI]

    Norman, Lisa

    2005-09-30T23:59:59.000Z

    When you return home after a disaster, you will want to have sturdy shoes, proper tools, clothes and medications for several days, and a first-aid kit. This publication also includes a list of necessary cleaning supplies....

  4. Supplies Needed Polyester Fleece (13" x 23")

    E-Print Network [OSTI]

    Supplies Needed Polyester Fleece (13" x 23") Polyester Thread This one is easy. Really easy inclined, add a drawstring to the top and it will double as a hat. Pretty cool, eh? Texas 4-H Clothing

  5. Supply chain and the executive agenda

    E-Print Network [OSTI]

    Peruvankal, James Paul

    2011-01-01T23:59:59.000Z

    In recent years, supply chain pundits and consultants emphasized the importance of strategies such as just-in-time, lean manufacturing, off- shoring or frequent deliveries to retail outlets. However, with significant ...

  6. Global Energy: Supply, Demand, Consequences, Opportunities

    ScienceCinema (OSTI)

    Arun Majumdar

    2010-01-08T23:59:59.000Z

    July 29, 2008 Berkeley Lab lecture: Arun Majumdar, Director of the Environmental Energy Technologies Division, discusses current and future projections of economic growth, population, and global energy demand and supply, and explores the implications of these trends for the environment.

  7. Risk in the Global Supply Chain

    E-Print Network [OSTI]

    Datta, Shoumen

    2006-01-01T23:59:59.000Z

    Carbon footprints are not on the priority list of risk analysts in operations management for at least half or more of global businesses. What are the other risks in the global supply chain?

  8. Power supply noise in delay testing 

    E-Print Network [OSTI]

    Wang, Jing

    2009-05-15T23:59:59.000Z

    As technology scales into the Deep Sub-Micron (DSM) regime, circuit designs have become more and more sensitive to power supply noise. Excessive noise can significantly affect the timing performance of DSM designs and cause ...

  9. Northeast Gasoline Supply Reserve | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    supplements the Northeast Home Heating Oil Reserve, a one million barrel supply of ultra-low sulfur diesel, which was used for the first time by first-responders and to fill...

  10. Competitive developments in the electric supply industry

    SciTech Connect (OSTI)

    Bruder, G.F.; Lively, M.

    1996-12-31T23:59:59.000Z

    Competition in the electric supply industry is outlined. The following topics are discussed: six impending major developments in the electric industry; recent and projected developments in the industry; where is the industry headed?; and what the future holds.

  11. Response to changes in demand/supply

    E-Print Network [OSTI]

    Response to changes in demand/supply through improved marketing 21.2 #12;#12;111 Impacts of changes operating by some Korean paper companies for acquiring needed pulpwood as a first step for the construction

  12. How to Reduce Energy Supply Costs 

    E-Print Network [OSTI]

    Swanson, G.

    2007-01-01T23:59:59.000Z

    customers control their supply-side costs of energy. Specific topics include distributive wind power generation and solid fuel boilers. It identities factors to consider in determining whether these technologies are economically viable for customers...

  13. Hierarchical Hybrid Power Supply Networks Farinaz Koushanfar

    E-Print Network [OSTI]

    management, hybrid power supply, supercapacitors 1. INTRODUCTION AND MOTIVATION Historically, almost all in a hierarchical power sup- ply network would include batteries, supercapacitors, ionic supercapacitors, and future cycle, supercapacitors are advantageous rel- ative to the standard che

  14. The supply chain response to environmental pressures

    E-Print Network [OSTI]

    Paquette, Julie Rebecca

    2006-01-01T23:59:59.000Z

    Understanding and shaping the relationship between supply chain management and the natural environment is critical not only to human health and the environment, but to the future success of business. While the cumulative ...

  15. RECYCLING: SUPPLY, ECONOMICS, ENVIRONMENT, AND TECHNOLOGY

    E-Print Network [OSTI]

    Abubakr, Said

    RECYCLING: SUPPLY, ECONOMICS, ENVIRONMENT, AND TECHNOLOGY Panel Discussion Roundtable Moderator: S, although higher market values for recyclable will certainly stimulate increased interest in collection in recycling and deinking technologies and process design among North American, European, and Pacific Rim

  16. Impact of demographics on supply chain risk management practices

    E-Print Network [OSTI]

    Kanyagui, Kenneth (Kenneth K.)

    2010-01-01T23:59:59.000Z

    Do demographic factors play a role in the choice of supply chain risk management practices by supply chain professionals? Are there stronger relationships between certain demographic factors and supply chain risk management ...

  17. Securing the Sustainability of Global Medical Nuclear Supply Chains

    E-Print Network [OSTI]

    Nagurney, Anna

    Securing the Sustainability of Global Medical Nuclear Supply Chains Through Economic Cost Recovery University of Massachusetts Amherst Securing the Sustainability of Medical Nuclear Supply Chains #12 of Massachusetts Amherst Securing the Sustainability of Medical Nuclear Supply Chains #12;This presentation

  18. Dynamic Electric Power Supply Chains and Transportation Networks

    E-Print Network [OSTI]

    Nagurney, Anna

    Dynamic Electric Power Supply Chains and Transportation Networks: an Evolutionary Variational energy Electric power supply chains, provide the foundations for theElectric power supply chains, provide and societies. Communication, transportation, heating, lighting, cooling,Communication, transportation, heating

  19. Air Handling Unit Supply Air Temperature Optimization During Economizer Cycles

    E-Print Network [OSTI]

    Xu, K.; Liu, M.; Wang, G.; Wang, Z.

    2007-01-01T23:59:59.000Z

    temperature at supply air temperature setpoint. Mechanical cooling is always required when outside air temperature is higher than the supply air temperature setpoint. Generally the supply air temperature setpoint is set at 55°F for space humidity control...

  20. An engineering approach to improving hospital supply chains

    E-Print Network [OSTI]

    Cheng, Scott Hsiang-Jen

    2008-01-01T23:59:59.000Z

    This thesis explores supply chain management practices that have been implemented, and have improved supply chains in industries outside of healthcare. The presented supply chain practices have been selected because they ...

  1. Integrated Planning and Management for Urban Water Supplies

    E-Print Network [OSTI]

    Pasternack, Gregory B.

    Positions for Water Supply Reliability ................................. 15 4 Shortage Management Modeling.2: Diagram of Water Supply Reliability Model Structure ..................49 5.3: Steps Used in ShortageIntegrated Planning and Management for Urban Water Supplies Considering Multiple Uncertainties Jay

  2. Seasonal demand and supply analysis of turkeys

    E-Print Network [OSTI]

    Blomo, Vito James

    1972-01-01T23:59:59.000Z

    SEASONAL DEMAND AND SUPPLY ANALYSIS OF TURKEYS A Thesis by VITO JAMES BLOMO Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE May 1972 Ma)or Sub...)ect: Agricultural Economics SEASONAL DEMAND AND SUPPLY ANALYSIS OF TURKEYS A Thesis by VITO JAMES BLOMO Approved as to style and content by: (Chairman of C mmittee) (Head of Department) (Member) (Member) ( ber) (Memb er) May 1972 ABSTRACT Seasonal...

  3. Application of oxygen-enriched combustion for locomotive diesel engines. Phase 1

    SciTech Connect (OSTI)

    Poola, R.B.; Sekar, R.R.; Assanis, D.N.

    1996-09-01T23:59:59.000Z

    A thermodynamic simulation is used to study the effects of oxygen-enriched intake air on the performance and nitrogen oxide (NO) emissions of a locomotive diesel engine. The parasitic power of the air separation membrane required to supply the oxygen-enriched air is also estimated. For a given constraint on peak cylinder pressure, the gross and net power outputs of an engine operating under different levels of oxygen enrichment are compared with those obtained when a high-boost turbocharged engine is used. A 4% increase in peak cylinder pressure can result in an increase in net engine power of approximately 13% when intake air with an oxygen content of 28% by volume is used and fuel injection timing is retarded by 4 degrees. When the engine is turbocharged to a higher inlet boost, the same increase in peak cylinder pressure improves power by only 4%. If part of the significantly higher exhaust enthalpies available as a result of oxygen enrichment are recovered, the power requirements of the air separator membrane can be met, resulting in substantial net power improvements. Oxygen enrichment reduces particulate and visible smoke emissions but increases NO emissions. However, a combination of retarded fuel injection timing and post-treatment of exhaust gases may be adequate to meet the locomotive diesel engine NO{sub x} standards. Exhaust gas after-treatment and heat recovery would be required to realize the full potential of oxygen enrichment. Economic analysis shows that oxygen-enrichment technology is economically feasible and provides high returns on investment. The study also indicates the strong influence of membrane parasitic requirements and exhaust energy recovery on economic benefits. To obtain an economic advantage while using a membrane with higher parasitic power requirements, it is necessary to recover a part of the exhaust energy.

  4. The marine biodiversity curve is an icon of paleobiology. The familiar curve shows

    E-Print Network [OSTI]

    Waxman, David

    the temperate phage infects Escherichia coli, it enters one of two pathways: lytic (replicates and killsThe marine biodiversity curve is an icon of paleobiology. The familiar curve shows increasing (distinct rock units) as a proxy for the amount of marine rock available for paleontological sampling

  5. Quantum Coherence and Closed Timelike Curves

    E-Print Network [OSTI]

    S. W. Hawking

    1995-02-08T23:59:59.000Z

    Various calculations of the $S$ matrix have shown that it seems to be non unitary for interacting fields when there are closed timelike curves. It is argued that this is because there is loss of quantum coherence caused by the fact that part of the quantum state circulates on the closed timelike curves and is not measured at infinity. A prescription is given for calculating the superscattering matrix $\\$ $ on space times whose parameters can be analytically continued to obtain a Euclidean metric. It is illustrated by a discussion of a spacetime in with two disks in flat space are identified. If the disks have an imaginary time separation, this corresponds to a heat bath. An external field interacting with the heat bath will lose quantum coherence. One can then analytically continue to an almost real separation of the disks. This will give closed timelike curves but one will still get loss of quantum coherence.

  6. OXYGEN 18 EXCHANGE REACTIONS OF ALDEHYDES AND KETONES

    E-Print Network [OSTI]

    Byrn, Marianne; Calvin, Melvin

    1965-01-01T23:59:59.000Z

    OXYGEN 18 EXCHANGE REACTIONS OF ALDEHYDES AND KETONES TWO-eng-48 OXYGEN 18 EXCHANGE REACTIONS OF ALDEHYDES AND KETONES

  7. ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT...

    Energy Savers [EERE]

    RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT RECORDS ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT RECORDS The basic procurement files reflect a...

  8. Small business success story: Gordon Electric Supply, Inc. |...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Small business success story: Gordon Electric Supply, Inc. May 14, 2013 Tweet EmailPrint Gordon Electric Supply has provided electrical and lighting products and services in the...

  9. ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT...

    Office of Environmental Management (EM)

    ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT RECORDS ADMINISTRATIVE RECORDS SCHEDULE 3: PROCUREMENT, SUPPLY, AND GRANT RECORDS The basic procurement files...

  10. EO 13211: Regulations That Significantly Affect Energy Supply...

    Energy Savers [EERE]

    1: Regulations That Significantly Affect Energy Supply, Distribution, or Use EO 13211: Regulations That Significantly Affect Energy Supply, Distribution, or Use I am requiring that...

  11. ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues...

    Energy Savers [EERE]

    ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues In a Densified Large Square Bale Format ABSTRACT: Bioenergy Harvesting Technologies to Supply Crop Residues In a...

  12. Model for Energy Supply System Alternatives and their General...

    Open Energy Info (EERE)

    for Energy Supply System Alternatives and their General Environmental Impacts (MESSAGE) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Model for Energy Supply System...

  13. Engine Driven Combined Heat and Power: Arrow Linen Supply, December...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Engine Driven Combined Heat and Power: Arrow Linen Supply, December 2008 Engine Driven Combined Heat and Power: Arrow Linen Supply, December 2008 This paper describes the Arrow...

  14. Advanced Supply System Validation Workshop | Department of Energy

    Office of Environmental Management (EM)

    of biomass to biorefineries annually Advanced supply system concepts, including depots Business models for advanced supply systems Siting and sizing considerations for depots...

  15. Addressing Biomass Supply Chain Challenges With AFEX(tm) Technology...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Addressing Biomass Supply Chain Challenges With AFEX(tm) Technology Addressing Biomass Supply Chain Challenges With AFEX(tm) Technology Plenary IV: Advances in Bioenergy...

  16. angeles water supply: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    it is possible Griffin, Ronald 6 CLIMATE CHANGE AND WATER SUPPLY SECURITY Energy Storage, Conversion and Utilization Websites Summary: CLIMATE CHANGE AND WATER SUPPLY...

  17. Hydrogen Supply: Cost Estimate for Hydrogen Pathways-Scoping...

    Broader source: Energy.gov (indexed) [DOE]

    Supply: Cost Estimate for Hydrogen Pathways-Scoping Analysis. January 22, 2002-July 22, 2002 Hydrogen Supply: Cost Estimate for Hydrogen Pathways-Scoping Analysis. January 22,...

  18. An investigation on stochastic specific activity curves

    E-Print Network [OSTI]

    Lee, Dominic Yat-Hung

    1973-01-01T23:59:59.000Z

    . into homogeneous components called. compartment s. (3) The system is in steady state, i. e. , compartments have a constant size and. are connected by fixed. flow rates. (4) The introduction of tracer does not alter the behavior of the system. (5) The system... 0. 10 SA (t) SA (t) Figure 3. 2. 2 Deterministic Specific Activity-Time Curve With stochastic flow of the tracer, the curves shown in Figure 3. 2. 2 (p. 10) would not be smooth, instead. they take the form as shown in Figure 4. 2. 1 (p. 18...

  19. Chiral gap effect in curved space

    E-Print Network [OSTI]

    Antonino Flachi; Kenji Fukushima

    2015-05-29T23:59:59.000Z

    We discuss a new type of QCD phenomenon induced in curved space. In the QCD vacuum, a mass-gap of Dirac fermions is attributed to the spontaneous breaking of chiral symmetry. If the curvature is positive large, the chiral condensate melts but a chiral invariant mass-gap can still remain, which we name the chiral gap effect in curved space. This leads to decoupling of quark deconfinement which implies a view of black holes surrounded by a first-order QCD phase transition.

  20. Developments in ITM oxygen technology for IGCC

    SciTech Connect (OSTI)

    Stein, V.E.E.; Richards, R.E.

    1999-07-01T23:59:59.000Z

    In partnership with the U.S. Department of Energy (DOE), an Air Products-led team (with Ceramatec, Eltron Research, McDermott Technology, NREC, Texaco, the Pennsylvania State University, and the University of Pennsylvania) is developing a new technology for air separation - Ion Transport Membrane Oxygen - based on the use of mixed-conducting ceramic membranes that have both electronic and oxygen ionic conductivity when operated at high temperature, typically 800 to 900 C. Under the influence of an oxygen partial-pressure driving force, the ITM Oxygen process achieves a high-purity, high-flux separation of oxygen from a compressed-air stream. By integrating the energy-rich, oxygen-depleted, non-permeate stream with a gas turbine system, the ITM Oxygen process becomes a co-producer of high-purity oxygen, power, and steam. Under a recent CRADA entitled ``Ion Transport Membranes (ITM) for Oxygen-Blown IGCC Systems and Indirect Coal Liquefaction,'' Air Products and DOE completed an initial quantification of the benefits of an ITM Oxygen-integrated IGCC facility. Compared to the cryogenic oxygen base case, the ITM Oxygen technology can potentially: reduce total installed costs by 7%; improve thermal efficiency for the integrated IGCC system by about 3%, leading to further decreases in carbon dioxide and sulfur emissions; and reduce the cost of generated electric power by more than 6%. The ITM Oxygen development project will proceed in three phases. Phase 1, which commenced under a DOE Cooperative Agreement in October 1998, is a 3-year effort focusing on construction of a technology development unit (TDU) for process concept validation tests at a capacity of 0.1 ton-per-day (TPD) oxygen. To accomplish this objective, the Air Products team will address relevant technical challenges in ITM Oxygen materials, engineering, membrane module development, and performance testing. During Phase 1 the team will also verify the economic prospects for integrating ITM Oxygen technology with IGCC and other advanced power generation systems. After at least one intermediate scaleup, Phase 2 and 3 activities will culminate with scaleup to a 25- to 50-TPD pre-commercial demonstration unit, fully integrated with a gas turbine. Meeting these challenges of developing cost-effective fabrication techniques for ITM Oxygen devices, and successfully integrating them with commercially available gas turbine engines, is key to bringing ITM Oxygen technology to the marketplace.

  1. Complex Fluid Analysis with the Advanced Distillation Curve Approach

    E-Print Network [OSTI]

    Complex Fluid Analysis with the Advanced Distillation Curve Approach Thomas J. Bruno, Lisa S. Ott for measuring distillation curves reveals the physicochemical properties of complex fluids such as fuels distillation curves of complex fluids. The distillation curve provides the only practical avenue to assess

  2. Type Ia supernovae from exploding oxygen-neon white dwarfs

    E-Print Network [OSTI]

    Marquardt, Kai S; Ruiter, Ashley J; Seitenzahl, Ivo R; Ohlmann, Sebastian T; Kromer, Markus; Pakmor, Ruediger; Roepke, Friedrich K

    2015-01-01T23:59:59.000Z

    The progenitor problem of Type Ia supernovae (SNe Ia) is still unsolved. Most of these events are thought to be explosions of carbon-oxygen (CO) white dwarfs (WDs), but for many of the explosion scenarios, particularly those involving the externally triggered detonation of a sub-Chandrasekhar mass WD (sub-M Ch WD), there is also a possibility of having an oxygen-neon (ONe) WD as progenitor. We simulate detonations of ONe WDs and calculate synthetic observables from these models. The results are compared with detonations in CO WDs of similar mass and observational data of SNe Ia. We perform hydrodynamic explosion simulations of detonations in initially hydrostatic ONe WDs for a range of masses below the Chandrasekhar mass (M Ch), followed by detailed nucleosynthetic postprocessing with a 384-isotope nuclear reaction network. The results are used to calculate synthetic spectra and light curves, which are then compared with observations of SNe Ia. We also perform binary evolution calculations to determine the nu...

  3. Research Summary Estimating Woodfuel Resource Cost Curves

    E-Print Network [OSTI]

    and extraction methods. Background Just under half of the final energy consumed in the UK (49%) is in the formResearch Summary Estimating Woodfuel Resource Cost Curves As a renewable energy source, woodfuel. The woodfuel strategy adopted by Forestry Commission England supports delivery of these. It aims to sustainably

  4. Closed timelike curves in general relativity

    E-Print Network [OSTI]

    W. B. Bonnor

    2002-11-13T23:59:59.000Z

    Many solutions of Einstein's field equations contain closed timelike curves (CTC). Some of these solutions refer to ordinary materials in situations which might occur in the laboratory, or in astrophysics. It is argued that, in default of a reasonable interpretation of CTC, general relativity does not give a satisfactory account of all phenomena within its terms of reference.

  5. WILD MODELS OF CURVES DINO LORENZINI

    E-Print Network [OSTI]

    Lorenzini, Dino J.

    WILD MODELS OF CURVES DINO LORENZINI Abstract. Let K be a complete discrete valuation field of X/K obtained by desingularizing the wild quotient singularities of the quotient Y/H. The most of wild quotient singularities having pairwise distinct resolution graphs. The information on the regular

  6. Myocardial Reloading after Extracorporeal Membrane Oxygenation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Protein Synthesis. Abstract: Extracorporeal membrane oxygenation (ECMO) unloads the heart providing a bridge to recovery in children after myocardial stunning. Mortality after...

  7. The Role of Oxygen in Coal Gasification

    E-Print Network [OSTI]

    Klosek, J.; Smith, A. R.; Solomon, J.

    in downst eam absorbs oxygen from air at low pressure by units. Selection of the optimum oxygen urHy contact with a circulating molten salt. High must be performed by optimizing the capit land purity (>99.5%) oxygen is regenerated from the operating... are evaluated, the use of oxygen is often preferred over air regardless of the pressure requirement. GOX GAN WASTE AIR FROM MOL SIEVE MAIN EXCHANGERS EXPANDER Figure 4 - Low Pressure Cryogenic Cycle Below about 95% purity, the specific power (k...

  8. International Oil Supplies and Demands. Volume 2

    SciTech Connect (OSTI)

    Not Available

    1992-04-01T23:59:59.000Z

    The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--1990 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world`s dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group`s thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

  9. Petroleum supply annual, 1997. Volume 2

    SciTech Connect (OSTI)

    NONE

    1998-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

  10. Petroleum supply annual 1998: Volume 2

    SciTech Connect (OSTI)

    NONE

    1999-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1998 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. This second volume contains final statistics for each month of 1998, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

  11. Petroleum supply annual 1996: Volume 2

    SciTech Connect (OSTI)

    NONE

    1997-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1996 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Capacity; each with final annual data. The second volume contains final statistics for each month of 1996, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

  12. Petroleum supply annual 1995: Volume 2

    SciTech Connect (OSTI)

    NONE

    1996-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1995 through monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and selected Refinery Statistics each with final annual data. The second volume contains final statistics for each month of 1995, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary.

  13. International Oil Supplies and Demands. Volume 1

    SciTech Connect (OSTI)

    Not Available

    1991-09-01T23:59:59.000Z

    The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--90 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world`s dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group`s thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

  14. Power-Supply-Network Design in 3D Integrated Systems

    E-Print Network [OSTI]

    Lim, Sung Kyu

    Power-Supply-Network Design in 3D Integrated Systems Michael B. Healy and Sung Kyu Lim School power-supply noise in a layout- level 3D design prototype, and the impact of possible 3D-specific changes to the power-supply network design and topology. Our results show that distributing power-supply

  15. Evaluate Supply and Recovery of Woody Biomass for Energy

    E-Print Network [OSTI]

    Gray, Matthew

    Biomass Recovery DataContrasting Woody Biomass Recovery Data Forest Biomass Supply in the Southeastern4/11/2011 1 Evaluate Supply and Recovery of Woody Biomass for Energy Production from Natural. Other studies of biomass supply have supply have assumedassumed a technical recovery rate

  16. A Supply Chain Generalized Network Oligopoly Model for Pharmaceuticals

    E-Print Network [OSTI]

    Nagurney, Anna

    dollars in drugs, vaccines, and other medical supplies were found spoiled, stolen, or unaccounted for

  17. BS Major in Supply Chain and Marketing Sciences

    E-Print Network [OSTI]

    Lin, Xiaodong

    Industry Week's 2010 Salary Survey, the average supply chain manager in the manufacturer sector was $98,130, up slightly from 2009. In another salary survey from the Institute for Supply Management (ISM. What is a Supply Chain? CROCS MFG Supply Chain Management is the way business gets done! #12;U

  18. Conversion of Mixed Oxygenates Generated from Synthesis Gas to Fuel Range Hydrocarbon

    SciTech Connect (OSTI)

    Ramasamy, Karthikeyan K.; Gerber, Mark A.; Lilga, Michael A.; Flake, Matthew D.

    2012-08-19T23:59:59.000Z

    The growing dependence in the U.S. on foreign crude oil supplies and increased concerns regarding greenhouse gas emission has generated considerable interest in research to develop renewable and environmentally friendly liquid hydrocarbon transportation fuels. One of the strategies for achieving this is to produce intermediate compounds such as alcohols and other simple oxygenates from biomass generated synthesis gas (mixture of carbon monoxide and hydrogen) and further convert them into liquid hydrocarbons. The focus of this research is to investigate the effects of mixed oxygenates intermediate product compositions on the conversion step to produce hydrocarbon liquids. A typical mixed oxygenate stream is expected to contain water (around 50%), alcohols, such as methanol and ethanol (around 35%), and smaller quantities of oxygenates such as acetaldehyde, acetic acid and ethyl acetate. However the ratio and the composition of the mixed oxygenate stream generated from synthesis gas vary significantly depending on the catalyst used and the process conditions. Zeolite catalyzed deoxygenation of methanol accompanied by chain growth is well understood under Methanol-to-Gasoline (MTG) like reaction conditions using an H-ZSM-5 zeolite as the catalyst6-8. Research has also been conducted to a limited extent in the past with higher alcohols, but not with other oxygenates present9-11. Also there has been little experimental investigation into mixtures containing substantial amounts of water. The latter is of particular interest because water separation from the hydrocarbon product would be less energy intensive than first removing it from the oxygenate intermediate stream prior to hydrocarbon synthesis, potentially reducing overall processing costs.

  19. Oxygen ion-beam microlithography

    DOE Patents [OSTI]

    Tsuo, Y. Simon (Lakewood, CO)

    1991-01-01T23:59:59.000Z

    A method of providing and developing a resist on a substrate for constructing integrated circuit (IC) chips includes the following steps: of depositing a thin film of amorphous silicon or hydrogenated amorphous silicon on the substrate and exposing portions of the amorphous silicon to low-energy oxygen ion beams to oxidize the amorphous silicon at those selected portions. The nonoxidized portions are then removed by etching with RF-excited hydrogen plasma. Components of the IC chip can then be constructed through the removed portions of the resist. The entire process can be performed in an in-line vacuum production system having several vacuum chambers. Nitrogen or carbon ion beams can also be used.

  20. Oxygen ion-beam microlithography

    DOE Patents [OSTI]

    Tsuo, Y.S.

    1991-08-20T23:59:59.000Z

    A method of providing and developing a resist on a substrate for constructing integrated circuit (IC) chips includes the following steps: of depositing a thin film of amorphous silicon or hydrogenated amorphous silicon on the substrate and exposing portions of the amorphous silicon to low-energy oxygen ion beams to oxidize the amorphous silicon at those selected portions. The nonoxidized portions are then removed by etching with RF-excited hydrogen plasma. Components of the IC chip can then be constructed through the removed portions of the resist. The entire process can be performed in an in-line vacuum production system having several vacuum chambers. Nitrogen or carbon ion beams can also be used. 5 figures.

  1. Transient oxygen consumption rate measurements with the BDT?M? oxygen biosensor system

    E-Print Network [OSTI]

    Low, Clarke Alan

    2008-01-01T23:59:59.000Z

    Oxygen consumption rate (OCR) is a reliable indicator of tissue health. Recently, the OCR of isolated human islets has been shown to predict transplant outcome in diabetic mice. The Oxygen Biosensor System (OBS) is a ...

  2. Petroleum supply annual 1998: Volume 1

    SciTech Connect (OSTI)

    NONE

    1999-06-01T23:59:59.000Z

    The ``Petroleum Supply Annual`` (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1998 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1998, and replaces data previously published in the PSA. The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. 16 figs., 59 tabs.

  3. Updated U.S. Geothermal Supply Characterization

    SciTech Connect (OSTI)

    Petty, S.; Porro, G.

    2007-03-01T23:59:59.000Z

    This paper documents the approach taken to characterize and represent an updated assessment of U.S. geothermal supply for use in forecasting the penetration of geothermal electrical generation in the National Energy Modeling System (NEMS). This work is motivated by several factors: The supply characterization used as the basis of several recent U.S. Department of Energy (DOE) forecasts of geothermal capacity is outdated; additional geothermal resource assessments have been published; and a new costing tool that incorporates current technology, engineering practices, and associated costs has been released.

  4. High density adsorbed oxygen on Rh,,111... and enhanced routes to metallic oxidation using atomic oxygen

    E-Print Network [OSTI]

    Sibener, Steven

    High density adsorbed oxygen on Rh,,111... and enhanced routes to metallic oxidation using atomic oxygen K. D. Gibson, Mark Viste, Errol C. Sanchez, and S. J. Sibener The James Franck Institute; accepted 30 November 1998 Exposure of Rh 111 to atomic oxygen leads to the facile formation of a full

  5. Curved butterfly bileaflet prosthetic cardiac valve

    DOE Patents [OSTI]

    McQueen, David M. (185 Hillside Ave., Chatham, NJ 07928); Peskin, Charles S. (186 Harrard Dr., Hartsdale, NY 10530)

    1991-06-25T23:59:59.000Z

    An annular valve body having a central passageway for the flow of blood therethrough with two curved leaflets each of which is pivotally supported on an accentric positioned axis in the central passageway for moving between a closed position and an open position. The leaflets are curved in a plane normal to the eccentric axis and positioned with the convex side of the leaflets facing each other when the leaflets are in the open position. Various parameters such as the curvature of the leaflets, the location of the eccentric axis, and the maximum opening angle of the leaflets are optimized according to the following performance criteria: maximize the minimum peak velocity through the valve, maximize the net stroke volume, and minimize the mean forward pressure difference, thereby reducing thrombosis and improving the hemodynamic performance.

  6. Field Theory on Curved Noncommutative Spacetimes

    E-Print Network [OSTI]

    Alexander Schenkel; Christoph F. Uhlemann

    2010-08-03T23:59:59.000Z

    We study classical scalar field theories on noncommutative curved spacetimes. Following the approach of Wess et al. [Classical Quantum Gravity 22 (2005), 3511 and Classical Quantum Gravity 23 (2006), 1883], we describe noncommutative spacetimes by using (Abelian) Drinfel'd twists and the associated *-products and *-differential geometry. In particular, we allow for position dependent noncommutativity and do not restrict ourselves to the Moyal-Weyl deformation. We construct action functionals for real scalar fields on noncommutative curved spacetimes, and derive the corresponding deformed wave equations. We provide explicit examples of deformed Klein-Gordon operators for noncommutative Minkowski, de Sitter, Schwarzschild and Randall-Sundrum spacetimes, which solve the noncommutative Einstein equations. We study the construction of deformed Green's functions and provide a diagrammatic approach for their perturbative calculation. The leading noncommutative corrections to the Green's functions for our examples are derived.

  7. Light Curves of Swift Gamma Ray Bursts

    E-Print Network [OSTI]

    Paolo Cea

    2006-09-22T23:59:59.000Z

    Recent observations from the Swift gamma-ray burst mission indicate that a fraction of gamma ray bursts are characterized by a canonical behaviour of the X-ray afterglows. We present an effective theory which allows us to account for X-ray light curves of both (short - long) gamma ray bursts and X-ray rich flashes. We propose that gamma ray bursts originate from massive magnetic powered pulsars.

  8. Detection of interlayer communication using type curves

    E-Print Network [OSTI]

    Tiefenthal, Sven A.

    1988-01-01T23:59:59.000Z

    with the adjacent formation through type curve analysis. The response caused by the essentially infinite acting producing zone alone can be filtered out using desuperposition. The remaining response is the "deviation function" caused by the leaking fault. Type.... TABLE OF CONTENTS Page ABSTRACT. ACKNOWLEDGEMENTS TABLE OF CONTENTS. LIST OF TABLES . V1 . viii LIST OF FIGURES. . . . . IX INTRODUCTION BACKGROUND THEORY Infinite Acting Reservoir. Linear Discontinuities. Fault Parameterization. . . . 8 9...

  9. OPTICAL PHASE CURVES OF KEPLER EXOPLANETS

    SciTech Connect (OSTI)

    Esteves, Lisa J.; De Mooij, Ernst J. W.; Jayawardhana, Ray, E-mail: esteves@astro.utoronto.ca, E-mail: demooij@astro.utoronto.ca, E-mail: rayjay@astro.utoronto.ca [Astronomy and Astrophysics, University of Toronto, 50 St. George Street, Toronto, Ontario M5S 3H4 (Canada)

    2013-07-20T23:59:59.000Z

    We conducted a comprehensive search for optical phase variations of all close-in (a/R{sub *} < 10) planet candidates in 15 quarters of Kepler space telescope data. After correcting for systematics, we found eight systems that show secondary eclipses as well as phase variations. Of these, five (Kepler-5, Kepler-6, Kepler-8, KOI-64, and KOI-2133) are new and three (TrES-2, HAT-P-7, and KOI-13) have published phase curves, albeit with many fewer observations. We model the full phase curve of each planet candidate, including the primary and secondary transits, and derive their albedos, dayside and nightside temperatures, ellipsoidal variations, and Doppler beaming. We find that KOI-64 and KOI-2133 have nightside temperatures well above their equilibrium values (while KOI-2133 also has an albedo, >1), so we conclude that they are likely to be self-luminous objects rather than planets. The other six candidates have characteristics consistent with their being planets with low geometric albedos (<0.3). For TrES-2 and KOI-13, the Kepler bandpass appears to probe atmospheric layers hotter than the planet's equilibrium temperature. For KOI-13, we detect a never-before-seen third cosine harmonic with an amplitude of 6.7 {+-} 0.3 ppm and a phase shift of -1.1 {+-} 0.1 rad in the phase curve residual, possibly due to its spin-orbit misalignment. We report derived planetary parameters for all six planets, including masses from ellipsoidal variations and Doppler beaming, and compare our results to published values when available. Our results nearly double the number of Kepler exoplanets with measured phase curve variations, thus providing valuable constraints on the properties of hot Jupiters.

  10. Galaxy rotation curves in de Sitter space

    E-Print Network [OSTI]

    Maurice H. P. M. van Putten

    2015-01-27T23:59:59.000Z

    Dark energy inferred from the observed negative deceleration parameter introduces a small mass of the graviton, that satisfies the Higuchi stability condition. It implies an infra-red modification of gravitation that produces Milgrom's inverse distance law of gravitational attraction in excellent agreement with the observed galaxy rotation curves. We conclude that dark matter is present cosmologically with no need for local clustering in galaxies.

  11. Oxygen and Nitrogen Contamination During Arc Welding

    E-Print Network [OSTI]

    Eagar, Thomas W.

    ) ) : ,- Oxygen and Nitrogen Contamination During Arc Welding T. W. Eagar Department of }faterials, shielded metal arc, self-shielded metal arc, and submerged arc welding are reviewed. Calcu- lations upon heating is also discussed. Introduction Oxygen and nitrogen ~ontamination of weld metal

  12. New Oxygen-Production Technology Proving Successful

    Broader source: Energy.gov [DOE]

    The Office of Fossil Energy's National Energy Technology Laboratory has partnered with Air Products and Chemicals Inc. of Allentown, Penn. to develop the Ion Transport Membrane (ITM) Oxygen, a revolutionary new oxygen-production technology that requires less energy and offers lower capital costs than conventional technologies.

  13. Pacific Northwest Power Supply Adequacy Assessment

    E-Print Network [OSTI]

    . Based on an assessment prepared by the Resource Adequacy Forum, the plan noted that relying only that this assessment is not a substitute for a comprehensive resource acquisition plan. The optimal amount and mixPacific Northwest Power Supply Adequacy Assessment for 2017 Final Report November 21, 2012 Council

  14. Capacity additions ease tight methanol supply

    SciTech Connect (OSTI)

    Greek, B.F. (C and EN, Houston, TX (US))

    1988-10-03T23:59:59.000Z

    Two menthanol plants now in operation - one in the U.S., the other in Chile - will boost global supplies of methanol more than 375 million gal annually. This large capacity addition and smaller expansions in other parts of the world will exceed demand growth during 1988 and 1989, easing the squeeze on supplies. As the result of increased supplies, methanol prices could slip slightly in the fourth quarter. They are more likely to decline next year, however. The two plants, which started up in August, are owned and operated by Tenneco Oil Co. Processing and Marketing and by Cape Horn Methanol (CHM). The Tenneco plant, located in Pasadena, Tex., was restarted after a shutdown in 1982 when prices for methanol were low. It now is running at full capacity of 125 million gal per year. The plant uses the low-pressure process technology of Lurgi, reportedly requiring for feedstock and energy between 100,000 and 125,000 cu ft of methane per gallon. Global trade in methanol smooths out the supply and demand inconsistencies. Surging methanol demand in the U.S. and in Western Europe has been met by imports from areas where methanol production is most economical - that is, where natural gas is readily available and has no other application as high in value. Canada, Chile, and Trinidad are examples of those areas.

  15. Petroleum supply annual 1996: Volume 1

    SciTech Connect (OSTI)

    NONE

    1997-06-01T23:59:59.000Z

    The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1996 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Capacity; each with final annual data. The summary statistics section show 16 years of data depicting the balance between supply, disposition and ending stocks for various commodities including crude oil, motor gasoline, distillate fuel oil, residual fuel oil, jet fuel propane/propylene, and liquefied petroleum gases. The detailed statistics section provide 1996 detailed statistics on supply and disposition, refinery operations, imports and exports, stocks, and transportation of crude oil and petroleum products. The refinery capacity contain listings of refineries and associated crude oil distillation and downstream capacities by State, as of January 1, 1997, as well as summaries of corporate refinery capacities and refinery storage capacities. In addition, refinery receipts of crude oil by method of transportation for 1996 are provided. Also included are fuels consumed at refineries, and lists of shutdowns, sales, reactivations, and mergers during 1995 and 1996. 16 figs., 59 tabs.

  16. Petroleum supply annual 1993. Volume 2

    SciTech Connect (OSTI)

    Not Available

    1994-06-01T23:59:59.000Z

    This publication contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1993 through annual and monthly surveys. This second volume contains final statistics for each month of 1993.

  17. Petroleum Supply Monthly, June 1984. [Contains glossary

    SciTech Connect (OSTI)

    Not Available

    1984-08-01T23:59:59.000Z

    This issue features a mid-year petroleum review. The article discusses changes in consumption, domestic crude oil production, exploration and development activity, refinery operations, foreign trade, stocks (including the Strategic Petroleum Reserve), and prices. A special summary of changes in petroleum imports is included. The Petroleum Supply Reporting System is reviewed.

  18. Solar Supply Chain and Market Driver Analysis 

    E-Print Network [OSTI]

    Martinez, Nicholas 1990-

    2012-05-09T23:59:59.000Z

    This study aims to explore the evolution of the photovoltaic supply chain in the United States and the drivers which foster growth of the solar market. The study will gather knowledge on the growth of the solar market and roles of different firms...

  19. Supply Chain Analysis Center for Transportation Analysis

    E-Print Network [OSTI]

    , Distribution network configuration, Reverse logistics, and Inventory levels and positioning. Integration configuration of the supply chain? What should be the modal configuration for the distribution network? How operations of the Defense Distribution Center. The analysis included a review of suppliers, distribution

  20. University of North Florida Logistics and Supply

    E-Print Network [OSTI]

    Asaithambi, Asai

    AST&L University of North Florida Logistics and Supply Chain Management Logistics and distribution skills training to begin and advance your career #12;Certification in Transportation and Logistics Cohort Program The UNF Certification in Transportation and Logistics (CTL) Cohort Program is a jointly sponsored

  1. Fossil fuels supplies modeling and research

    SciTech Connect (OSTI)

    Leiby, P.N.

    1996-06-01T23:59:59.000Z

    The fossil fuel supplies modeling and research effort focuses on models for US Strategic Petroleum Reserve (SPR) planning and management. Topics covered included new SPR oil valuation models, updating models for SPR risk analysis, and fill-draw planning. Another task in this program area is the development of advanced computational tools for three-dimensional seismic analysis.

  2. Rotation Curve Measurement using Cross-Correlation

    E-Print Network [OSTI]

    Elizabeth J. Barton; Sheila J. Kannappan; Michael J. Kurtz; Margaret J. Geller

    2000-06-20T23:59:59.000Z

    Longslit spectroscopy is entering an era of increased spatial and spectral resolution and increased sample size. Improved instruments reveal complex velocity structure that cannot be described with a one-dimensional rotation curve, yet samples are too numerous to examine each galaxy in detail. Therefore, one goal of rotation curve measurement techniques is to flag cases in which the kinematic structure of the galaxy is more complex than a single-valued curve. We examine cross-correlation as a technique that is easily automated and works for low signal-to-noise spectra. We show that the technique yields well-defined errors which increase when the simple spectral model (template) is a poor match to the data, flagging those cases for later inspection. We compare the technique to the more traditional, parametric technique of simultaneous emission line fitting. When the line profile at a single slit position is non-Gaussian, the techniques disagree. For our model spectra with two well-separated velocity components, assigned velocities from the two techniques differ by up to ~52% of the velocity separation of the model components. However, careful use of the error statistics for either technique allows one to flag these non-Gaussian spectra.

  3. Capillary migration of microdisks on curved interfaces

    E-Print Network [OSTI]

    Lu Yao; Nima Sharifi-Mood; Iris B. Liu; Kathleen J. Stebe

    2014-12-23T23:59:59.000Z

    The capillary energy landscape for particles on curved fluid interfaces is strongly influenced by the particle wetting conditions. Contact line pinning has now been widely reported for colloidal particles, but its implications in capillary interactions have not been addressed. Here, we present experiment and analysis for disks with pinned contact lines on curved fluid interfaces. In experiment, we study microdisk migration on a host interface with zero mean curvature; the microdisks have contact lines pinned at their sharp edges and are sufficiently small that gravitational effects are negligible. The disks migrate away from planar regions toward regions of steep curvature with capillary energies inferred from the dissipation along particle trajectories which are linear in the deviatoric curvature. We derive the curvature capillary energy for an interface with arbitrary curvature, and discuss each contribution to the expression. By adsorbing to a curved interface, a particle eliminates a patch of fluid interface and perturbs the surrounding interface shape. Analysis predicts that perfectly smooth, circular disks do not migrate, and that nanometric deviations from a planar circular, contact line, like those around a weakly roughened planar disk, will drive migration with linear dependence on deviatoric curvature, in agreement with experiment.

  4. Incorporating Experience Curves in Appliance Standards Analysis

    SciTech Connect (OSTI)

    Garbesi, Karina; Chan, Peter; Greenblatt, Jeffery; Kantner, Colleen; Lekov, Alex; Meyers, Stephen; Rosenquist, Gregory; Buskirk, Robert Van; Yang, Hung-Chia; Desroches, Louis-Benoit

    2011-10-31T23:59:59.000Z

    The technical analyses in support of U.S. energy conservation standards for residential appliances and commercial equipment have typically assumed that manufacturing costs and retail prices remain constant during the projected 30-year analysis period. There is, however, considerable evidence that this assumption does not reflect real market prices. Costs and prices generally fall in relation to cumulative production, a phenomenon known as experience and modeled by a fairly robust empirical experience curve. Using price data from the Bureau of Labor Statistics, and shipment data obtained as part of the standards analysis process, we present U.S. experience curves for room air conditioners, clothes dryers, central air conditioners, furnaces, and refrigerators and freezers. These allow us to develop more representative appliance price projections than the assumption-based approach of constant prices. These experience curves were incorporated into recent energy conservation standards for these products. The impact on the national modeling can be significant, often increasing the net present value of potential standard levels in the analysis. In some cases a previously cost-negative potential standard level demonstrates a benefit when incorporating experience. These results imply that past energy conservation standards analyses may have undervalued the economic benefits of potential standard levels.

  5. OXYGEN ENHANCED COMBUSTION FOR NOx CONTROL

    SciTech Connect (OSTI)

    David R. Thompson; Lawrence E. Bool; Jack C. Chen

    2001-04-01T23:59:59.000Z

    This quarterly technical progress report will summarize work accomplished for the Program through the fourth quarter January-March 2001 in the following task areas: Task 1 - Oxygen Enhanced Combustion, Task 2 - Oxygen Transport Membranes and Task 4 - Program Management. This report will also recap the results of the past year. The program is proceeding in accordance with the objectives for the first year. OTM material characterization was completed. 100% of commercial target flux was demonstrated with OTM disks. The design and assembly of Praxair's single tube high-pressure test facility was completed. The production of oxygen with a purity of better than 99.5% was demonstrated. Coal combustion testing was conducted at the University of Arizona. Modest oxygen enhancement resulted in NOx emissions reduction. The injector for oxygen enhanced coal based reburning was conducted at Praxair. Combustion modeling with Keystone boiler was completed. Pilot-scale combustion test furnace simulations continued this quarter.

  6. Comparative study of InGaP/GaAs high electron mobility transistors with upper and lower delta-doped supplied layers

    SciTech Connect (OSTI)

    Tsai, Jung-Hui, E-mail: jhtsai@nknucc.nknu.edu.tw; Ye, Sheng-Shiun [National Kaohsiung Normal University, Department of Electronic Engineering, Taiwan (China); Guo, Der-Feng [Air Force Academy, Kaohsiung, Department of Electronic Engineering, Taiwan (China); Lour, Wen-Shiung [National Taiwan Ocean University, Department of Electrical Engineering, Taiwan (China)

    2012-04-15T23:59:59.000Z

    Influence corresponding to the position of {delta}-doped supplied layer on InGaP/GaAs high electron mobility transistors is comparatively studied by two-dimensional simulation analysis. The simulated results exhibit that the device with lower {delta}-doped supplied layer shows a higher gate potential barrier height, a higher saturation output current, a larger magnitude of negative threshold voltage, and broader gate voltage swing, as compared to the device with upper {delta}-doped supplied layer. Nevertheless, it has smaller transconductance and inferior high-frequency characteristics in the device with lower {delta}-doped supplied layer. Furthermore, a knee effect in current-voltage curves is observed at low drain-to-source voltage in the two devices, which is investigated in this article.

  7. Application of NUREG/CR-5999 interim fatigue curves to selected nuclear power plant components

    SciTech Connect (OSTI)

    Ware, A.G.; Morton, D.K.; Nitzel, M.E. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

    1995-03-01T23:59:59.000Z

    Recent test data indicate that the effects of the light water reactor (LWR) environment could significantly reduce the fatigue resistance of materials used in the reactor coolant pressure boundary components of operating nuclear power plants. Argonne National Laboratory has developed interim fatigue curves based on test data simulating LWR conditions, and published them in NUREG/CR-5999. In order to assess the significance of these interim fatigue curves, fatigue evaluations of a sample of the components in the reactor coolant pressure boundary of LWRs were performed. The sample consists of components from facilities designed by each of the four U.S. nuclear steam supply system vendors. For each facility, six locations were studied, including two locations on the reactor pressure vessel. In addition, there are older vintage plants where components of the reactor coolant pressure boundary were designed to codes that did not require an explicit fatigue analysis of the components. In order to assess the fatigue resistance of the older vintage plants, an evaluation was also conducted on selected components of three of these plants. This report discusses the insights gained from the application of the interim fatigue curves to components of seven operating nuclear power plants.

  8. OXYGEN ENHANCED COMBUSTION FOR NOx CONTROL

    SciTech Connect (OSTI)

    David R. Thompson; Lawrence E. Bool; Jack C. Chen

    2004-04-01T23:59:59.000Z

    Conventional wisdom says adding oxygen to a combustion system enhances product throughput, system efficiency, and, unless special care is taken, increases NOx emissions. This increase in NOx emissions is typically due to elevated flame temperatures associated with oxygen use leading to added thermal NOx formation. Innovative low flame temperature oxy-fuel burner designs have been developed and commercialized to minimize both thermal and fuel NOx formation for gas and oil fired industrial furnaces. To be effective these systems require close to 100% oxy-fuel combustion and the cost of oxygen is paid for by fuel savings and other benefits. For applications to coal-fired utility boilers at the current cost of oxygen, however, it is not economically feasible to use 100% oxygen for NOx control. In spite of this conventional wisdom, Praxair and its team members, in partnership with the US Department of Energy National Energy Technology Laboratory, have developed a novel way to use oxygen to reduce NOx emissions without resorting to complete oxy-fuel conversion. In this concept oxygen is added to the combustion process to enhance operation of a low NOx combustion system. Only a small fraction of combustion air is replaced with oxygen in the process. By selectively adding oxygen to a low NOx combustion system it is possible to reduce NOx emissions from nitrogen-containing fuels, including pulverized coal, while improving combustion characteristics such as unburned carbon. A combination of experimental work and modeling was used to define how well oxygen enhanced combustion could reduce NOx emissions. The results of this work suggest that small amounts of oxygen replacement can reduce the NOx emissions as compared to the air-alone system. NOx emissions significantly below 0.15 lbs/MMBtu were measured. Oxygen addition was also shown to reduce carbon in ash. Comparison of the costs of using oxygen for NOx control against competing technologies, such as SCR, show that this concept offers substantial savings over SCR and is an economically attractive alternative to purchasing NOx credits or installing other conventional technologies. In conjunction with the development of oxygen based low NOx technology, Praxair also worked on developing the economically enhancing oxygen transport membrane (OTM) technology which is ideally suited for integration with combustion systems to achieve further significant cost reductions and efficiency improvements. This OTM oxygen production technology is based on ceramic mixed conductor membranes that operate at high temperatures and can be operated in a pressure driven mode to separate oxygen with infinite selectivity and high flux. An OTM material was selected and characterized. OTM elements were successfully fabricated. A single tube OTM reactor was designed and assembled. Testing of dense OTM elements was conducted with promising oxygen flux results of 100% of target flux. However, based on current natural gas prices and stand-alone air separation processes, ceramic membranes do not offer an economic advantage for this application. Under a different DOE-NETL Cooperative Agreement, Praxair is continuing to develop oxygen transport membranes for the Advanced Boiler where the economics appear more attractive.

  9. Analysis of natural gas supply strategies at Fort Drum

    SciTech Connect (OSTI)

    Stucky, D.J.; Shankle, S.A.; Anderson, D.M.

    1992-07-01T23:59:59.000Z

    This analysis investigates strategies for Fort Drum to acquire a reliable natural gas supply while reducing its gas supply costs. The purpose of this study is to recommend an optimal supply mix based on the life-cycle costs of each strategy analyzed. In particular, this study is intended to provide initial guidance as to whether or not the building and operating of a propane-air mixing station is a feasible alternative to the current gas acquisition strategy. The analysis proceeded by defining the components of supply (gas purchase, gas transport, supplemental fuel supply); identifying alternative options for each supply component; constructing gas supply strategies from different combinations of the options available for each supply component and calculating the life-cycle costs of each supply strategy under a set of different scenarios reflecting the uncertainty of future events.

  10. Experience curves for power plant emission control technologies

    E-Print Network [OSTI]

    Rubin, Edward S.; Yeh, Sonia; Hounshell, David A; Taylor, Margaret R

    2007-01-01T23:59:59.000Z

    Inc. Experience curves for power plant emission controlfor Coal-Fired Utility Power Plants, U.S. Environmental1/2, 2004 Experience curves for power plant emission control

  11. Visual Attention and Driver Performance at Horizontal Curves

    E-Print Network [OSTI]

    Brimley, Bradford K.

    2014-12-02T23:59:59.000Z

    Despite the frequency with which drivers encounter curves on highways, curves are regularly identified as locations that experience disproportionately high crash rates. Crash data suggest that inattention is one of the leading causes of crashes...

  12. Oxygen and organic matter thresholds for benthic faunal activity on the Pakistan margin oxygen minimum zone (7001100 m)

    E-Print Network [OSTI]

    Levin, Lisa

    Oxygen and organic matter thresholds for benthic faunal activity on the Pakistan margin oxygen increased animal activity associated with increasing bottom-water oxygen concentration. We examined faunal community responses to oxygen and organic matter gradients across the lower oxygen minimum zone (OMZ

  13. Oxygen Discharge and Post-Discharge Kinetics Experiments and Modeling for the Electric Oxygen-Iodine Laser System

    E-Print Network [OSTI]

    Carroll, David L.

    Oxygen Discharge and Post-Discharge Kinetics Experiments and Modeling for the Electric Oxygen a low-pressure oxygen/helium/nitric oxide discharge. In the electric discharge oxygen-iodine laser (ElectricOIL) the discharge production of atomic oxygen, ozone, and other excited species adds levels

  14. Endogeneity in the Environmental Kuznets Curve: An Instrumental Variables Approach

    E-Print Network [OSTI]

    Lin, C.-Y. Cynthia

    decreasing Inorganic contaminants Normally a few ug/l Burning fossil fuels and mining Fecal Coliform max Biological Oxygen Demand (mg/l) 2422 55 3.96 12.01 0.00 240.16 Chemical Oxygen Demand (mg/l) 1883 of Pollution Decreasing Chemical Oxygen Demand decreasing inverted-U decreasing/inverted-U Organic Matter N

  15. Long-term oxygen sensor implantation in the porcine subcutaneous environment

    E-Print Network [OSTI]

    Kumosa, Lucas Stefan

    2011-01-01T23:59:59.000Z

    Membrane-­?Covered  Oxygen  Electrode.   Analytical  Microvascular  and  tissue  oxygen   distribution.  vitro  stability  of  an  oxygen  sensor.   Anal  Chem,  

  16. Oxygen Tension Modulates Neurite Outgrowth in PC12 Cells Through A Mechanism Involving HIF and VEGF

    E-Print Network [OSTI]

    Genetos, Damian C.; Cheung, Whitney K.; Decaris, Martin L.; Leach, J. Kent

    2010-01-01T23:59:59.000Z

    neural repair. Keywords Oxygen tension . Neurite extension .respective physiological oxygen microenvironments (Chen etet al. 2008). For example, oxygen tension differentially

  17. On the oxygen abundance in our Galaxy

    E-Print Network [OSTI]

    L. S. Pilyugin; F. Ferrini; R. V. Shkvarun

    2003-02-03T23:59:59.000Z

    The compilation of published spectra of Galactic HII regions with available diagnostic [OIII]4363 line has been carried out. Our list contains 71 individual measurements of 13 HII regions in the range of galactocentric distances from 6.6 to 14.8 kpc. The oxygen abundances in all the HII regions were recomputed in the same way, using the classic Te - method. The oxygen abundance at the solar galactocentric distance traced by those HII regions is in agreement with the oxygen abundance in the interstellar medium in the solar vicinity derived with high precision from the interstellar absorption lines towards stars. The derived radial oxygen abundance distribution was compared with that for HII regions from the Shaver et al. (1983) sample which is the basis of many models for the chemical evolution of our Galaxy. It was found that the original Shaver et al.'s oxygen abundances are overestimated by 0.2-0.3 dex. Oxygen abundances in HII regions from the Shaver et al. sample have been redetermined with the recently suggested P - method. The radial distribution of oxygen abundances from the Shaver et al. sample redetermined with the P - method is in agreement with our radial distribution of (O/H)_Te abundances.

  18. COMPUTER GENERATION OF TYPE CURVES SUBMITIED TO THE DEPARTMENTOF PETROLEUMENGINEERING

    E-Print Network [OSTI]

    Stanford University

    COMPUTER GENERATION OF TYPE CURVES A REPORT SUBMITIED TO THE DEPARTMENTOF PETROLEUMENGINEERING data. This paper presents some previously published type curves and the computer programs that were between two parallel sealing faults. The governing equations for these curves are derived. The computer

  19. Length and Energy of Quadratic Bezier Curves and Applications

    E-Print Network [OSTI]

    Hoffmann, Christoph M.

    Length and Energy of Quadratic B´ezier Curves and Applications Young Joon Ahn a , Christoph for the arc length and the bending energy of quadratic B´ezier curves. The formulae are in terms control point is analyzed for curves of fixed arc length or bending energy. In the case of arc length

  20. RANKS OF ELLIPTIC CURVES WITH PRESCRIBED TORSION OVER NUMBER FIELDS

    E-Print Network [OSTI]

    Dujella, Andrej

    RANKS OF ELLIPTIC CURVES WITH PRESCRIBED TORSION OVER NUMBER FIELDS JOHAN BOSMAN, PETER BRUIN of all elliptic curves over quadratic fields with torsion subgroup T is empty, or it contains curves number fields. More explicitly, we will be interested in the following question: given a torsion group

  1. Algorithms for Mumford Curves Ralph Morrison and Qingchun Ren

    E-Print Network [OSTI]

    Boyer, Edmond

    discuss specific methods and future work for hyperelliptic Mumford curves. 1. Introduction Curves over non geometry, which looks at the images in Rn of curves under coordinate-wise valuation, these are balanced complete with respect to a nontrivial non-archimedean valuation. Unless otherwise stated, | · | will denote

  2. Tracking Endocardium Using Optical Flow along Iso-Value Curve

    E-Print Network [OSTI]

    1 Tracking Endocardium Using Optical Flow along Iso-Value Curve Qi Duan1, Elsa D. Angelini2 indicators. · A framework of optical flow along iso-value curves is proposed and applied to several cardiac;9 OF along Iso-value Curves · In myocardial motion analysis, motion fields are projected along specific

  3. Characterization of an oxygen suspension used for intravenous infusion

    E-Print Network [OSTI]

    Peña, Kristen Helen

    2012-01-01T23:59:59.000Z

    Oxygenated fluid mixture can be used to treat critically ill patients suffering from asphyxia, lung injury, and cardiac arrest. This oxygenated fluid delivered intravenously re-oxygenates the bloodstream, allowing for more ...

  4. Imaging Intrinsic Diffusion of Bridge-Bonded Oxygen Vacancies...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Intrinsic Diffusion of Bridge-Bonded Oxygen Vacancies on TiO2(110). Imaging Intrinsic Diffusion of Bridge-Bonded Oxygen Vacancies on TiO2(110). Abstract: Since oxygen atom...

  5. Oxygen Coverage Dependence of NO Oxidation on Pt(111). | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oxygen Coverage Dependence of NO Oxidation on Pt(111). Oxygen Coverage Dependence of NO Oxidation on Pt(111). Abstract: The interaction of NO with adsorbed atomic oxygen on Pt(111)...

  6. Reactive oxygen species: a breath of life or death?

    E-Print Network [OSTI]

    Fruehauf, John P; Meyskens, Frank L Jr

    2007-01-01T23:59:59.000Z

    AP1, activator protein-1; ODD, oxygen-dependent degradationSignaling response when oxygen levels decrease (Fig. 1C;3. Halliwell B. Reactive oxygen species in living sys- tems:

  7. Operational feasibility of underwater Stirling engine systems using oxygen-seawater extraction

    SciTech Connect (OSTI)

    Potter, I.J.; Reader, G.T. [Univ. of Calgary, Alberta (Canada). Dept. of Mechanical Engineering

    1995-12-31T23:59:59.000Z

    The exploration of the oceans whether for societal, commercial, scientific or military reasons requires efficient and cost effective underwater vehicles. In turn, these vessels require efficient means of producing on board power for the propulsion and hotel load requirements of long endurance missions. The Stirling engine, because of its inherent closed-cycle operation, has long been an attractive candidate for underwater use and now has proved its reliability and maintainability in the arduous environment of a naval submarine application. More recently the Stirling has been considered for use in small long endurance unmanned underwater vessels (UUVs). However, with these type of vehicles the need to carry an on board oxygen supply in a very confined space has presented a number of design problems. The concept of using multi-stage vehicles with disposable energy pods has been explored and appears attractive although a major change in submarine design philosophy will be required if such vehicles are to launched from submarines. Another approach is to use a more space efficient source of oxygen. As seawater contains dissolved oxygen then if this source could be utilized to meet all or at least part of the engine`s need than a major design problem could be overcome. In this paper the findings of an initial study into the use of membranes or artificial gill techniques to provide oxygen for a Stirling powered DARPA type vehicle are presented. It has been found that only in certain sea areas is the concept of oxygen extraction feasible for use with power systems. Even in situations where there are sufficient levels of dissolved oxygen the gill system approach appears to have limited utility for UUV applications and a number of practical problems still need to be addressed.

  8. Ambient dissolved oxygen concentrations in Delaware's Inland Bays. Final report, June 6, 1984

    SciTech Connect (OSTI)

    Biggs, R.B.

    1984-01-01T23:59:59.000Z

    Ambient dissolved oxygen concentrations were measured at dawn during August, 1983, in Rehoboth and Indian River Bays. In Indian River Bay, 59% of the D.O. measurements were below the State minimum water quality standard of 5 mg L/sup -1/, while in Rehoboth Bay 17% of the values fail to meet the State standards. Diurnal dissolved oxygen curves measured at 5 stations in the Bays and tributary creeks, provide evidence that, although the Bays are in reasonable balance with respect to apparent net daytime photosynthesis (Pa) and nighttime respiration (Rn), the absolute values of Pa and Rn are very high, compared with other coastal ecosystems, except for central Rehoboth Bay. These conclusions are consistent with the annual nutrient loads to the systems, which are about double for Indian River when contrasted with Rehoboth. 11 references, 1 figure, 7 tables.

  9. Petroleum Supply Monthly, September 1990. [Contains glossary

    SciTech Connect (OSTI)

    Whited, D.; Jacobus, P. (eds.)

    1990-11-28T23:59:59.000Z

    Data presented in this PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. 12 figs., 46 tabs.

  10. Petroleum supply monthly, October 1991. [Contains glossary

    SciTech Connect (OSTI)

    Not Available

    1991-10-30T23:59:59.000Z

    Data presented in this report describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importer, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics 14 figs., 56 tabs.

  11. Petroleum supply monthly, October 1990. [Contains Glossary

    SciTech Connect (OSTI)

    Not Available

    1990-12-27T23:59:59.000Z

    Data presented in this report describes the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. 12 figs., 54 tabs.

  12. Procurement Options for New Renewable Electricity Supply

    SciTech Connect (OSTI)

    Kreycik, C. E.; Couture, T. D.; Cory, K. S.

    2011-12-01T23:59:59.000Z

    State renewable portfolio standard (RPS) policies require utilities and load-serving entities (LSEs) to procure renewable energy generation. Utility procurement options may be a function of state policy and regulatory preferences, and in some cases, may be dictated by legislative authority. Utilities and LSEs commonly use competitive solicitations or bilateral contracting to procure renewable energy supply to meet RPS mandates. However, policymakers and regulators in several states are beginning to explore the use of alternatives, namely feed-in tariffs (FITs) and auctions to procure renewable energy supply. This report evaluates four procurement strategies (competitive solicitations, bilateral contracting, FITs, and auctions) against four main criteria: (1) pricing; (2) complexity and efficiency of the procurement process; (3) impacts on developers access to markets; and (4) ability to complement utility decision-making processes. These criteria were chosen because they take into account the perspective of each group of stakeholders: ratepayers, regulators, utilities, investors, and developers.

  13. Decline curve analysis for horizontal wells

    E-Print Network [OSTI]

    Shih, Min-Yu

    1994-01-01T23:59:59.000Z

    support kept me from losing sight of my goals. Thanks to Sam Hou, Joseph Wang, Robert Liau, James Wang, and Shou for their company and in particular to Li Fan and Mrs. Shou-Lee Chang for their caring and delicious meals when I forgot my dinner. Thanks... Pressure (L/2xe= 0. 2) Composite Dimensionless Flow Rate Integral and Flow Rate Integral Derivative Functions Type Curve for an Infinite-Conductivity Horizontal Well Located in the Center of a Square Drainage Area, Producing at Constant Bottomhole...

  14. Negative decline curves of coalbed degasification wells

    SciTech Connect (OSTI)

    Harrison, G.C.; Gordon, R.B.

    1984-05-01T23:59:59.000Z

    Production data from coalbed degasification wells characteristically exhibit a negative decline curve. The dynamics of this methane production are complex and interrelated. As production begins, water and free gas are often first recovered. Continued production lowers pressure and increases permeability to gas, allowing adsorbed gas to flow. This pressure drop within the formation causes sublimation whereby gas, which is absorbed within the coal, forms on the walls of the micropores. Finally, the desorption through production disturbs the chemical and physical equilibrium of the coal, thus enabling the coal to resume generation of methane.

  15. Modeling the Phillips curve with unobserved components

    E-Print Network [OSTI]

    Harvey, Andrew C

    is then nonstationary. However, writing the equation as #1;#25;t = #12;xt+"t makes it clear that what we have is not really a Phillips curve (though adding lags of xt and incorporating a unit root could retrieve the situation). On the other hand, a stationary model... -looking. The conditions under which a model with an expectational term reverts to (10) are derived below. The fact that the forecast function for a random walk component is constant simpli?es matters considerably. The reduced form of (10) is an ARMAX model in which #1;#25...

  16. Wave regularity in curve integrable spacetimes

    E-Print Network [OSTI]

    Yafet Sanchez Sanchez

    2015-02-23T23:59:59.000Z

    The idea of defining a gravitational singularity as an obstruction to the dynamical evolution of a test field (described by a PDE) rather than the dynamical evolution of a particle (described by a geodesics) is explored. In particular, the concept of wave regularity is introduced which serves to show that the classical singularities in curve integrable spacetimes do not interrupt the well-posedness of the wave equation. The techniques used also provide arguments that can be extended to establish when a classically singular spacetime remains singular in a semi-classical picture.

  17. Tetraoxygen on Reduced Ti02(110): Oxygen Adsorption and Reactions...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tetraoxygen on Reduced Ti02(110): Oxygen Adsorption and Reactions with Oxygen Vacancies. Tetraoxygen on Reduced Ti02(110): Oxygen Adsorption and Reactions with Oxygen Vacancies....

  18. On the maximum value of the cosmic abundance of oxygen and the oxygen yield

    E-Print Network [OSTI]

    L. S. Pilyugin; T. X. Thuan; J. M. Vilchez

    2007-01-11T23:59:59.000Z

    We search for the maximum oxygen abundance in spiral galaxies. Because this maximum value is expected to occur in the centers of the most luminous galaxies, we have constructed the luminosity - central metallicity diagram for spiral galaxies, based on a large compilation of existing data on oxygen abundances of HII regions in spiral galaxies. We found that this diagram shows a plateau at high luminosities (-22.3 oxygen abundance 12+log(O/H) ~ 8.87. This provides strong evidence that the oxygen abundance in the centers of the most luminous metal-rich galaxies reaches the maximum attainable value of oxygen abundance. Since some fraction of the oxygen (about 0.08 dex) is expected to be locked into dust grains, the maximum value of the true gas+dust oxygen abundance in spiral galaxies is 12+log(O/H) ~ 8.95. This value is a factor of ~ 2 higher than the recently estimated solar value. Based on the derived maximum oxygen abundance in galaxies, we found the oxygen yield to be about 0.0035, depending on the fraction of oxygen incorporated into dust grains.

  19. Method and apparatus for reducing cold-phase emissions by utilizing oxygen-enriched intake air

    DOE Patents [OSTI]

    Poola, Ramesh B. (Woodridge, IL); Sekar, Ramanujam R. (Naperville, IL); Stork, Kevin C. (Chicago, IL)

    1997-01-01T23:59:59.000Z

    An oxygen-enriched air intake control system for an internal combustion engine includes air directing apparatus to control the air flow into the intake of the engine. During normal operation of the engine, ambient air flowing from an air filter of the engine flows through the air directing apparatus into the intake of the engine. In order to decrease the amount of carbon monoxide (CO) and hydrocarbon (HC) emissions that tend to be produced by the engine during a short period of time after the engine is started, the air directing apparatus diverts for a short period of time following the start up of the engine at least a portion of the ambient air from the air filter through a secondary path. The secondary path includes a selectively permeable membrane through which the diverted portion of the ambient air flows. The selectively permeable membrane separates nitrogen and oxygen from the diverted air so that oxygen enriched air containing from about 23% to 25% oxygen by volume is supplied to the intake of the engine.

  20. CREATING THE NORTHEAST GASOLINE SUPPLY RESERVE

    Broader source: Energy.gov [DOE]

    In 2012, Superstorm Sandy made landfall in the northeastern United States and caused heavy damage to two refineries and left more than 40 terminals in New York Harbor closed due to water damage and loss of power. This left some New York gas stations without fuel for as long as 30 days. As part of the Obama Administration’s ongoing response to the storm, the Department of Energy created the first federal regional refined product reserve, the Northeast Gasoline Supply Reserve.

  1. A single power supply optoelectronic differential amplifier

    E-Print Network [OSTI]

    Choi, Youngmin Albert

    1987-01-01T23:59:59.000Z

    Coinmittee: Henry F. Taylor This thesis presents an approach to optoelectronic differential amplifier (ODA) design in which two avalanche photodiodes and two laser diodes are used instead of a rriatched pair of transistors. The approach is demonstrated... by the design and realization oi' a complete system which includes direct intensity modulation of laser diodes and a novel single power supply optical receiver. The ODA shows better than 25 dB common-mode rejection ratio (CMRR) over a bandwidth of greater...

  2. Electrochemical chlorination for purifying domestic water supplies

    E-Print Network [OSTI]

    Peters, Joseph Ludwig

    1973-01-01T23:59:59.000Z

    system for small zural watez supplies, This puzifica- tion system is being studied in the Department of Agricultural Engineezing under Texas Agricultural Experiment Station Pzoject H-1874M Pilot Plant Studies of Electrical Water Treatment for Small... and relatively maintenance-fzee has been considered in this thesis. This is a process in which natural chlorides in the raw water are subjected to electrolysis, thereby releasing free chlorine and hence disinfecting the water. An investigation was made...

  3. QER- Comment of Natural Gas Supply Association

    Broader source: Energy.gov [DOE]

    TO: Quadrennial Energy Review Task Force In response to the Department of Energy’s August 25, 2014 Federal Register Notice seeking input on the Quadrennial Energy Review, attached are comments from the Natural Gas Supply Association. Thank you for this opportunity to share our views on the important issue of energy infrastructure. If we can be of further assistance, please let me know. Regards,

  4. Equivalence of Real Elliptic CurvesEquivalence of Real Elliptic Curves Part 2Part 2 --Birational EquivalenceBirational Equivalence

    E-Print Network [OSTI]

    Broughton, S. Allen

    1 Equivalence of Real Elliptic CurvesEquivalence of Real Elliptic Curves Part 2Part 2 -- Birational EquivalenceBirational Equivalence Allen Broughton Rose-Hulman Institute of Technology #12;2 CreditsCredits Discussion with Ken McMurdy #12;3 OutlineOutline -- 11 Recap of linear equivalence Complex elliptic curves

  5. Oxygen-Enriched Combustion for Military Diesel Engine Generators...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Oxygen-Enriched Combustion for Military Diesel Engine Generators Oxygen-Enriched Combustion for Military Diesel Engine Generators Substantial increases in brake power and...

  6. Advantages of Oxygenates Fuels over Gasoline in Direct Injection...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advantages of Oxygenates Fuels over Gasoline in Direct Injection Spark Ignition Engines Advantages of Oxygenates Fuels over Gasoline in Direct Injection Spark Ignition Engines...

  7. avec oxygenation modelisation: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Experimental calibration of oxygen isotope fractionation between quartz and zircon Dustin Trail a the results of an experimental calibration of oxygen isotope fractionation...

  8. Electron-Stimulated Production of Molecular Oxygen in Amorphous...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Water. Electron-Stimulated Production of Molecular Oxygen in Amorphous Solid Water. Abstract: The low-energy, electron-stimulated production of molecular oxygen from pure amorphous...

  9. Oxygen Diffusion (OD) Dramatically Improves Wear-Resistance of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Oxygen Diffusion (OD) Dramatically Improves Wear-Resistance of Titanium Oxygen Diffusion (OD) Dramatically Improves Wear-Resistance of Titanium 2007 Diesel Engine-Efficiency &...

  10. Isolation, Characterization of an Intermediate in an Oxygen Atom...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Characterization of an Intermediate in an Oxygen Atom-Transfer Reaction, and the Determination of the Bond Isolation, Characterization of an Intermediate in an Oxygen Atom-Transfer...

  11. Theoretical Study of the Structure, Stability and Oxygen Reduction...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Study of the Structure, Stability and Oxygen Reduction Activity ofUltrathin Platinum Nanowires. Theoretical Study of the Structure, Stability and Oxygen Reduction Activity...

  12. Density Functional Study of the Structure, Stability and Oxygen...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Study of the Structure, Stability and Oxygen Reduction Activity of Ultrathin Platinum Nanowires. Density Functional Study of the Structure, Stability and Oxygen Reduction Activity...

  13. Testing Oxygen Reduction Reaction Activity with the Rotating...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Testing Oxygen Reduction Reaction Activity with the Rotating Disc Electrode Technique Testing Oxygen Reduction Reaction Activity with the Rotating Disc Electrode Technique...

  14. Fractionation of Oxygen Isotopes in Phosphate during its Interactions...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fractionation of Oxygen Isotopes in Phosphate during its Interactions with Iron Oxides. Fractionation of Oxygen Isotopes in Phosphate during its Interactions with Iron Oxides....

  15. Effects of Oxygen-Containing Functional Groups on Supercapacitor...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Effects of Oxygen-Containing Functional Groups on Supercapacitor Performance. Effects of Oxygen-Containing Functional Groups on Supercapacitor Performance. Abstract: Molecular...

  16. Oxygen detected in atmosphere of Saturn's moon Dione

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oxygen detected in atmosphere of Saturn's moon Dione Oxygen detected in atmosphere of Saturn's moon Dione Scientists and an international research team have announced discovery of...

  17. Virtual Oxygen Sensor for Innovative NOx and PM Emission Control...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Virtual Oxygen Sensor for Innovative NOx and PM Emission Control Technologies Virtual Oxygen Sensor for Innovative NOx and PM Emission Control Technologies A virtual O2 sensor for...

  18. Bimetallic and Ternary Alloys for Improved Oxygen Reduction Catalysis...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Bimetallic and Ternary Alloys for Improved Oxygen Reduction Catalysis . Bimetallic and Ternary Alloys for Improved Oxygen Reduction Catalysis . Abstract: The research described in...

  19. Direct Measurement of Oxygen Incorporation into Thin Film Oxides...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Measurement of Oxygen Incorporation into Thin Film Oxides at Room Temperature Upon Ultraviolet Phton Irradiation. Direct Measurement of Oxygen Incorporation into Thin Film Oxides...

  20. Oxygen Transport Studies in Nanocrystalline Ceria Films. | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Transport Studies in Nanocrystalline Ceria Films. Oxygen Transport Studies in Nanocrystalline Ceria Films. Abstract: Oxygen uptake and conductivity were measured by nuclear...

  1. Oxygen And Carbon Isotope Ratios Of Hydrothermal Minerals From...

    Open Energy Info (EERE)

    Oxygen And Carbon Isotope Ratios Of Hydrothermal Minerals From Yellowstone Drill Cores Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Oxygen...

  2. Density Functional Theory Study of Oxygen Reduction Activity...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Density Functional Theory Study of Oxygen Reduction Activity on Ultrathin Platinum Nanotubes. Density Functional Theory Study of Oxygen Reduction Activity on Ultrathin Platinum...

  3. Property Tax Exemption for Machinery, Equipment, Materials, and Supplies (Kansas)

    Broader source: Energy.gov [DOE]

    The Property Tax Exemption for Machinery, Equipment, Materials, and Supplies exists for low-dollar items of machinery, equipment, materials and supplies used for business purposes, or in activities...

  4. How Markets Slowly Digest Changes in Supply and Demand

    E-Print Network [OSTI]

    CHAPTER 2 How Markets Slowly Digest Changes in Supply and Demand Jean-Philippe Bouchaud Science-Holland, Elsevier, Inc. All rights reserved. 57 #12;58 Chapter 2 · How Markets Slowly Digest Changes in Supply

  5. Hydrogen storage of energy for small power supply systems

    E-Print Network [OSTI]

    Monaghan, Rory F. D. (Rory Francis Desmond)

    2005-01-01T23:59:59.000Z

    Power supply systems for cell phone base stations using hydrogen energy storage, fuel cells or hydrogen-burning generators, and a backup generator could offer an improvement over current power supply systems. Two categories ...

  6. Advanced Supply System Validation Workshop | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Supply System Validation Workshop Advanced Supply System Validation Workshop February 3, 2015 12:00PM MST to February 4, 2015 2:15PM MST National Renewable Energy...

  7. Designing a flexible supply chain for new product launch

    E-Print Network [OSTI]

    Ha, Wei-Kwan Benjamin

    2005-01-01T23:59:59.000Z

    This thesis examines how companies tactically design flexible supply chains for new product launches. The research focus is on different strategies and tactics used by original equipment manufacturers to improve supply ...

  8. Supply chain design: a conceptual model and tactical simulations 

    E-Print Network [OSTI]

    Brann, Jeremy Matthew

    2009-05-15T23:59:59.000Z

    In current research literature, supply chain management (SCM) is a hot topic breaching the boundaries of many academic disciplines. SCM-related work can be found in the relevant literature for many disciplines. Supply chain ...

  9. Vulnerability assessment of water supply systems for insufficient fire flows

    E-Print Network [OSTI]

    Kanta, Lufthansa Rahman

    2009-05-15T23:59:59.000Z

    supply systems are vulnerable to many forms of terrorist acts, most of the vulnerability analysis studies on these systems have been for chemical and biological threats. Because of the interdependency of water supply infrastructure and emergency fire...

  10. Effects of the drought on California electricity supply and demand

    E-Print Network [OSTI]

    Benenson, P.

    2010-01-01T23:59:59.000Z

    fossil fuel for thermal electric generation. This will beThermal-Electric Energy Supply The shortfall in hydroelectric energy supply will be made up prim- arily by greater reliance upon thermal generation

  11. Axiomatic quantum field theory in curved spacetime

    E-Print Network [OSTI]

    S. Hollands; R. M. Wald

    2008-03-13T23:59:59.000Z

    The usual formulations of quantum field theory in Minkowski spacetime make crucial use of features--such as Poincare invariance and the existence of a preferred vacuum state--that are very special to Minkowski spacetime. In order to generalize the formulation of quantum field theory to arbitrary globally hyperbolic curved spacetimes, it is essential that the theory be formulated in an entirely local and covariant manner, without assuming the presence of a preferred state. We propose a new framework for quantum field theory, in which the existence of an Operator Product Expansion (OPE) is elevated to a fundamental status, and, in essence, all of the properties of the quantum field theory are determined by its OPE. We provide general axioms for the OPE coefficients of a quantum field theory. These include a local and covariance assumption (implying that the quantum field theory is locally and covariantly constructed from the spacetime metric), a microlocal spectrum condition, an "associativity" condition, and the requirement that the coefficient of the identity in the OPE of the product of a field with its adjoint have positive scaling degree. We prove curved spacetime versions of the spin-statistics theorem and the PCT theorem. Some potentially significant further implications of our new viewpoint on quantum field theory are discussed.

  12. Light curves from rapidly rotating neutron stars

    E-Print Network [OSTI]

    Numata, Kazutoshi

    2010-01-01T23:59:59.000Z

    We calculate light curves produced by a hot spot of a rapidly rotating neutron star, assuming that the spot is perturbed by a core $r$-mode, which is destabilized by emitting gravitational waves. To calculate light curves, we take account of relativistic effects such as the Doppler boost due to the rapid rotation and light bending assuming the Schwarzschild metric around the neutron star. We assume that the core $r$-modes penetrate to the surface fluid ocean to have sufficiently large amplitudes to disturb the spot. For a $l'=m$ core $r$-mode, the oscillation frequency $\\omega\\approx2m\\Omega/[l'(l'+1)]$ defined in the co-rotating frame of the star will be detected by a distant observer, where $l'$ and $m$ are respectively the spherical harmonic degree and the azimuthal wave number of the mode, and $\\Omega$ is the spin frequency of the star. In a linear theory of oscillation, using a parameter $A$ we parametrize the mode amplitudes such that ${\\rm max}\\left(|\\xi_\\theta|,|\\xi_\\phi|\\right)/R=A$ at the surface, w...

  13. Algebraic quantum field theory in curved spacetimes

    E-Print Network [OSTI]

    Christopher J. Fewster; Rainer Verch

    2015-04-02T23:59:59.000Z

    This article sets out the framework of algebraic quantum field theory in curved spacetimes, based on the idea of local covariance. In this framework, a quantum field theory is modelled by a functor from a category of spacetimes to a category of ($C^*$)-algebras obeying supplementary conditions. Among other things: (a) the key idea of relative Cauchy evolution is described in detail, and related to the stress-energy tensor; (b) a systematic "rigidity argument" is used to generalise results from flat to curved spacetimes; (c) a detailed discussion of the issue of selection of physical states is given, linking notions of stability at microscopic, mesoscopic and macroscopic scales; (d) the notion of subtheories and global gauge transformations are formalised; (e) it is shown that the general framework excludes the possibility of there being a single preferred state in each spacetime, if the choice of states is local and covariant. Many of the ideas are illustrated by the example of the free Klein-Gordon theory, which is given a new "universal definition".

  14. Design optimization of oxygenated fluid pump

    E-Print Network [OSTI]

    Piazzarolo, Bruno Aiala

    2012-01-01T23:59:59.000Z

    In medical emergencies, an oxygen-starved brain quickly suffers irreparable damage. In many cases, patients who stop breathing can be resuscitated but suffer from brain damage. Dr. John Kheir from Boston Children's Hospital ...

  15. Reactive Gliosis Reactive Oxygen Species: Superoxide

    E-Print Network [OSTI]

    . By sensing the electric signals generated by other 3368 Reactive Gliosis #12;individuals, mormyrids are alsoReactive Gliosis Glial Scar Reactive Oxygen Species: Superoxide Anions Neuroinflammation motor output. Reafferent Control in Electric Communication Reafferent Control in Electric Communication

  16. Electron-impact excitation of neutral oxygen

    E-Print Network [OSTI]

    P. S. Barklem

    2006-09-25T23:59:59.000Z

    Aims: To calculate transition rates from ground and excited states in neutral oxygen atoms due to electron collisions for non-LTE modelling of oxygen in late-type stellar atmospheres, thus enabling reliable interpretation of oxygen lines in stellar spectra. Methods: A 38-state R-matrix calculation in LS-coupling has been performed. Basis orbitals from the literature (Thomas et al.) are adopted, and a large set of configurations are included to obtain good representations of the target wavefunctions. Rate coefficients are calculated by averaging over a Maxwellian velocity distribution. Results: Estimates for the cross sections and rate coefficients are presented for transitions between the seven lowest LS states of neutral oxygen. The cross sections for excitation from the ground state compare well with existing experimental and recent theoretical results.

  17. Dynamic Nuclear Polarization of Oxygen-17

    E-Print Network [OSTI]

    Michaelis, Vladimir K.

    Oxygen-17-detected DNP NMR of a water/glycerol glass enabled an 80-fold enhancement of signal intensity at 82 K, using the biradical TOTAPOL. The >6000-fold savings in acquisition time enable [superscript 17]O–[superscript ...

  18. Essays on the Economics of Environmental Issues: The Environmental Kuznets Curve to Optimal Energy Portfolios

    E-Print Network [OSTI]

    Meininger, Aaron G.

    2012-01-01T23:59:59.000Z

    Issues: The Environmental Kuznets Curve to Optimal EnergyE. (2005), “An environmental kuznets curve analysis of u.s.proach to environmental kuznets curves using the ecological

  19. Searching for Empirical Regularity and Theoretical Structure: The Environmental Kuznets Curve

    E-Print Network [OSTI]

    Carson, Richard T

    2009-01-01T23:59:59.000Z

    of the environmental Kuznets curve. Journal of Publicof the environmental Kuznets curve studies. Agriculture andhypothesis and environmental Kuznets Curve: examining the

  20. DEVELOPING FLOW AND HEAT TRANSFER IN STRONGLY CURVED DUCTS OF RECTANGULAR CROSS-SECTION

    E-Print Network [OSTI]

    Yee, G.

    2010-01-01T23:59:59.000Z

    DEVELOpiNG FLOW AND HEAT TRANSFER IN STRONGLY CURVED DUCTS9092 Developing Flow and Heat Transfer in Strongly CurvedForced Convection Heat Transfer in Curved Rectangular

  1. Effects of the drought on California electricity supply and demand

    E-Print Network [OSTI]

    Benenson, P.

    2010-01-01T23:59:59.000Z

    DEMAND . . . .Demand for Electricity and Power PeakDemand . . • . . ELECTRICITY REQUIREMENTS FOR AGRICULTUREResults . . Coriclusions ELECTRICITY SUPPLY Hydroelectric

  2. Supplying Renewable Energy to Deferrable Loads: Algorithms and Economic Analysis

    E-Print Network [OSTI]

    Oren, Shmuel S.

    in renewable power supply may take hours, lead to additional air pollution, result in wear and the need

  3. Look at natural gas supplies: room for cautious optimism. [USA

    SciTech Connect (OSTI)

    Teitelbaum, D.F.

    1981-09-10T23:59:59.000Z

    Projections of natural gas availability made only on a national level tend to mask major changes in regional reserves and production, resulting in overly optimistic estiamtes of future supplies. The Zinder annual gas-supply report - based on regional analyses - projects that conventional production will decline more than 50% below current levels by 2000. The development of alternative sources of natural gas (through unconventional production and importation) could maintain a constant level of total gas supplies despite the falling supply of conventional gas.

  4. Direct current uninterruptible power supply method and system

    DOE Patents [OSTI]

    Sinha, Gautam

    2003-12-02T23:59:59.000Z

    A method and system are described for providing a direct current (DC) uninterruptible power supply with the method including, for example: continuously supplying fuel to a turbine; converting mechanical power from the turbine into alternating current (AC) electrical power; converting the AC electrical power to DC power within a predetermined voltage level range; supplying the DC power to a load; and maintaining a DC load voltage within the predetermined voltage level range by adjusting the amount of fuel supplied to the turbine.

  5. Magnetism in Lithium–Oxygen Discharge Product

    SciTech Connect (OSTI)

    Lu, Jun; Jung, Hun-Ji; Lau, Kah Chun; Zhang, Zhengcheng; Schlueter, John A.; Du, Peng; Assary, Rajeev S.; Greeley, Jeffrey P.; Ferguson, Glen A.; Wang, Hsien-Hau; Hassoun, Jusef; Iddir, Hakim; Zhou, Jigang; Zuin, Lucia; Hu, Yongfeng; Sun, Yang-Kook; Scrosati, Bruno; Curtiss, Larry A.; Amine, Khalil

    2013-05-13T23:59:59.000Z

    Nonaqueous lithium–oxygen batteries have a much superior theoretical gravimetric energy density compared to conventional lithium-ion batteries, and thus could render long-range electric vehicles a reality. A molecular-level understanding of the reversible formation of lithium peroxide in these batteries, the properties of major/minor discharge products, and the stability of the nonaqueous electrolytes is required to achieve successful lithium–oxygen batteries. We demonstrate that the major discharge product formed in the lithium–oxygen cell, lithium peroxide, exhibits a magnetic moment. These results are based on dc-magnetization measurements and a lithium– oxygen cell containing an ether-based electrolyte. The results are unexpected because bulk lithium peroxide has a significant band gap. Density functional calculations predict that superoxide- type surface oxygen groups with unpaired electrons exist on stoichiometric lithium peroxide crystalline surfaces and on nanoparticle surfaces; these computational results are consistent with the magnetic measurement of the discharged lithium peroxide product as well as EPR measurements on commercial lithium peroxide. The presence of superoxide-type surface oxygen groups with spin can play a role in the reversible formation and decomposition of lithium peroxide as well as the reversible formation and decomposition of electrolyte molecules.

  6. Atomic Oxygen in the Comae of Comets

    E-Print Network [OSTI]

    Anita L. Cochran

    2008-07-03T23:59:59.000Z

    We report on the detection of atomic oxygen lines in the spectra of 8 comets. These forbidden lines are a result of the photodissociation of the parent oxygen-bearing species directly into an excited state. We used high resolution spectra obtained at the McDonald Observatory 2.7m telescope to resolve the cometary oxygen lines from the telluric oxygen lines and from other cometary emissions. We find that the relative intensities of the two red lines (6300.304 and 6363.776A) are consistent with theory. The green line (5577.339A) has an intensity which is about 10% of the sum of the intensities of the two red lines. We show that collisional quenching may be important in the inner coma. If we assume the relative excitation rates of potential parents which have appeared in the literature, then H2O would be the parent of the cometary green oxygen line. However, those rates have been questioned. We measured the width of the three oxygen lines and find that the green line is wider than either of the two red lines. The finding of a wider line could imply a different parent for the green and red lines. However, the constancy of the green to red line flux ratio suggests the parent is the same for these lines but that the exciting photons have different energies.

  7. Physical modeling of the soil swelling curve vs. the shrinkage curve

    E-Print Network [OSTI]

    V. Y. Chertkov

    2014-04-14T23:59:59.000Z

    Physical understanding of the links between soil swelling, texture, structure, cracking, and sample size is of great interest for the physical understanding of many processes in the soil-air-water system and for applications in civil, agricultural, and environmental engineering. The background of this work is an available chain of interconnected physical shrinkage curve models for clay, intra-aggregate matrix, aggregated soil without cracks, and soil with cracks. The objective of the work is to generalize these models to the case of swelling, and to construct the physical-swelling-model chain with a step-by-step transition from clay to aggregated soil with cracks. The generalization is based on thorough accounting for the analogies and differences between shrinkage and swelling and the corresponding use, modification, or replacement of the soil shrinkage features. Two specific soil swelling features to be used are: (i) air entrapping in pores of the contributing clay; and (ii) aggregate destruction with the formation of new aggregate surfaces. The input for the prediction of the swelling curve of an aggregated soil coincides with that of the available model of the shrinkage curve. The analysis of available data on the maximum shrink-swell cycle of two soils with different texture and structure, accounting for sample size is conducted as applied to swelling curves and to the residual crack volume and maximum-swelling-volume decrease after the shrink-swell cycle. Results of the analysis show evidence in favor of the swelling model chain.

  8. Curved Spacetimes and Curved Graphene: a status report of the Weyl-symmetry approach

    E-Print Network [OSTI]

    Alfredo Iorio

    2014-12-15T23:59:59.000Z

    This is a status report about the ongoing work on the realization of quantum field theory on curved graphene spacetimes that uses Weyl symmetry. The programme is actively pursued from many different perspectives. Here we point to what has been done, and to what needs to be done.

  9. STANDARD TERMS OF PURCHASE APPLICABLE TO SUPPLY AND SERVICES CONTRACTS

    E-Print Network [OSTI]

    Chamroukhi, Faicel

    STANDARD TERMS OF PURCHASE APPLICABLE TO SUPPLY AND SERVICES CONTRACTS ENTERED INTO BY SUD TOULON and its co-contracting parties for all government supplies and services contracts entered into pursuant supply and services contracts in its version annexed to the Decree of 19 January 2009 approving

  10. Simulating the Afghanistan-Pakistan opium supply chain

    SciTech Connect (OSTI)

    Watkins, Jennifer H [Los Alamos National Laboratory; MacKerrow, Edward P [Los Alamos National Laboratory; Merritt, Terence M [Los Alamos National Laboratory

    2010-04-08T23:59:59.000Z

    This paper outlines an opium supply chain using the Hilmand province of Afghanistan as exemplar. The opium supply chain model follows the transformation of opium poppy seed through cultivation and chemical alteration to brown heroin base. The purpose of modeling and simulating the Afghanistan-Pakistan opium supply chain is to discover and test strategies that will disrupt this criminal enterprise.

  11. Supply Regulation Techniques for Phase-Locked Loops

    E-Print Network [OSTI]

    Palermo, Sam

    Supply Regulation Techniques for Phase-Locked Loops Vivekananth Gurumoorthy and Samuel Palermo-- Phase-locked loops (PLLs) which employ voltage regulators for low supply-noise sensitivity often rely. This paper compares various supply regulation techniques on the basis of their ability to reject noise from

  12. Departmentof SupplyChainManagement andMarketingSciences

    E-Print Network [OSTI]

    Lin, Xiaodong

    Solutions with ERP/SAP II[1] (3) 22:799:661 Introduction to Project Management (3) 22:799:677 Fundamentals Resource Planning Systems 22:799:659 Supply Chain Solutions with ERP/SAP I 22:799:660 Supply Chain:799:650 Supply Chain Management Industry Project (required for full-time students; elective for part

  13. Securing the Sustainability of Global Medical Nuclear Supply Chains

    E-Print Network [OSTI]

    Nagurney, Anna

    Securing the Sustainability of Global Medical Nuclear Supply Chains Through Economic Cost Recovery-17, 2012 University of Massachusetts Amherst Securing the Sustainability of Medical Nuclear Supply Chains-2013. University of Massachusetts Amherst Securing the Sustainability of Medical Nuclear Supply Chains #12;This

  14. Mo Supply Chain for Nuclear Medicine Ladimer S. Nagurney

    E-Print Network [OSTI]

    Nagurney, Anna

    The 99 Mo Supply Chain for Nuclear Medicine Ladimer S. Nagurney Department of Electrical November 13, 2012 #12;Nuclear Medicine: Meeting Patient Needs with 99 Mo Ladimer S. Nagurney The 99 Mo Supply Chain #12;Background and Motivation Study of Nuclear Medicine Supply Chains is a combination

  15. Alberta's Energy Reserves 2007 and Supply/Demand Outlook

    E-Print Network [OSTI]

    Laughlin, Robert B.

    Alberta's Energy Reserves 2007 and Supply/Demand Outlook 2008-2017 0 ST98-2008 Energy Resources RESOURCES CONSERVATION BOARD ST98-2008: Alberta's Energy Reserves 2007 and Supply/Demand Outlook 2008: Reserves Andy Burrowes, Rick Marsh, Nehru Ramdin, and Curtis Evans; Supply/Demand and Economics

  16. Hybrid Heterogeneous Energy Supply Networks Farinaz Koushanfar and Azalia Mirhoseini

    E-Print Network [OSTI]

    Hybrid Heterogeneous Energy Supply Networks Farinaz Koushanfar and Azalia Mirhoseini Department--Efficient energy supply, storage, and distribution are key technical challenges for design and operation of electronic systems. In particular, energy supply is the most scarce resource and constraint for mobile

  17. Optimization of California's Water Supply System: Results and Insights

    E-Print Network [OSTI]

    Pasternack, Gregory B.

    headings: Optimization; California; Water supply; Water shortage. Introduction Water is scarceOptimization of California's Water Supply System: Results and Insights Marion W. Jenkins1 ; Jay R-engineering optimization model of California's water supply system. The results of this 4-year effort illustrate the value

  18. Risk management in Chemical Supply Chains Rajagopalan Srinivasana,b

    E-Print Network [OSTI]

    Alvarado, Matías

    an agent-based framework for modeling and simulating the supply chain activities in a refinery, and operations in the refinery. Other external agents emulate the crude exchange, oil suppliers, and 3PLs attention. As an example, consider a petroleum refinery supply chain. 1.1. Petroleum Refinery Supply Chain

  19. THE JET PULSE POWER SUPPLY SYSTEM J. B. HICKS

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    between the two major components of the power supply (flywheel-generator-convertors (FGC) and transformer between the two possible components of the power supply, i. e. flywheel. generator-convertors and transformer-controlled-convertors. The proposed JET power supply system is described, together with an outline

  20. Supply chain management (SCM) involves the management of materials and information across the entire supply chain. This includes raw material

    E-Print Network [OSTI]

    Calgary, University of

    Supply chain management (SCM) involves the management of materials and information across this concentration will be required to take three core courses: Materials and Supply Chain Management, Transportation Purchasing identify global sources of materials, select vendors, and manage negotiati

  1. Hydrogen atom on curved noncommutative space

    E-Print Network [OSTI]

    V. G. Kupriyanov

    2013-06-05T23:59:59.000Z

    We have calculated the hydrogen atom spectrum on curved noncommutative space defined by the commutation relations $\\left[ \\hat {x}^{i},\\hat{x}^{j}\\right] =i\\theta\\hat{\\omega}^{ij}\\left( \\hat {x}\\right) $, where $\\theta$ is the parameter of noncommutativity. The external antisymmetric field which determines the noncommutativity is chosen as $\\omega^{ij}(x) =\\varepsilon^{ijk}{x}_{k}f\\left( {x_i}x^{i}\\right) $. In this case the rotational symmetry of the system is conserved, preserving the degeneracy of the energy spectrum. The contribution of the noncommutativity appears as a correction to the fine structure. The corresponding nonlocality is calculated: $\\Delta x\\Delta y \\geq \\frac{\\theta^2}{4} |m\\langle f^2\\rangle| $, where $m$ is a magnetic quantum number.

  2. Remote quantum states in curved spacetime

    E-Print Network [OSTI]

    Charles Francis

    2014-07-06T23:59:59.000Z

    It is seen that issues of the evolution of the wave function in curved spacetime can be resolved by describing the evolution of quantum states in Minkowski tangent space, in accordance with the orthodox interpretation that the wave function is not physical but is part of a mathematical method for the calculation of probabilities of measurement results. The teleconnection is defined between Hilbert spaces at different points in spacetime motivated by arguments from the probability interpretation. The teleconnection is analogous to a connection between vector spaces and reduces to the Levi-Civita connection in the limit of near initial and final measurements. Gravitational redshift is as in classical general relativity, as is the redshift for the cosmological microwave background. An argument is given that the cosmological redshift of photons treated as quantum particles should be treated differently. If correct this argument has important implications for the age of the universe, galaxy evolution and missing matter.

  3. Undergraduate Curriculum tied for second, MBA Program tied for third In a 2011 supply chain management study by Gartner Supply

    E-Print Network [OSTI]

    Lin, Xiaodong

    management study by Gartner Supply Chain Leaders, a survey of how well leading universities are educating professionals to contend with a rapidly changing landscape, the Rutgers Business School Supply Chain Management Supply Chain Management programs in the country, Rutgers Business School showed its "perceived value

  4. Description & Careers Supply Chain Management is how business gets done. Supply chain management spans all movement and storage of raw

    E-Print Network [OSTI]

    Lin, Xiaodong

    management spans all movement and storage of raw materials, work-in-process inventory, and finished goods of supply chains, resource managers of material or manufacturing resources planning (MRP), and processDescription & Careers The Field Supply Chain Management is how business gets done. Supply chain

  5. Description & Careers Supply Chain Management is how business gets done. Supply chain management spans all movement and storage of raw

    E-Print Network [OSTI]

    Lin, Xiaodong

    management spans all movement and storage of raw materials, work-in-process inventory, and finished goods managers of supply chains, resource managers of material or manufacturing resources planning (MRPDescription & Careers The Field Supply Chain Management is how business gets done. Supply chain

  6. SUPERNOVA LIGHT CURVES POWERED BY FALLBACK ACCRETION

    SciTech Connect (OSTI)

    Dexter, Jason; Kasen, Daniel, E-mail: jdexter@berkeley.edu [Departments of Physics and Astronomy, University of California, Berkeley, CA 94720 (United States)

    2013-07-20T23:59:59.000Z

    Some fraction of the material ejected in a core collapse supernova explosion may remain bound to the compact remnant, and eventually turn around and fall back. We show that the late time ({approx}>days) power potentially associated with the accretion of this 'fallback' material could significantly affect the optical light curve, in some cases producing super-luminous or otherwise peculiar supernovae. We use spherically symmetric hydrodynamical models to estimate the accretion rate at late times for a range of progenitor masses and radii and explosion energies. The accretion rate onto the proto-neutron star or black hole decreases as M-dot {proportional_to}t{sup -5/3} at late times, but its normalization can be significantly enhanced at low explosion energies, in very massive stars, or if a strong reverse shock wave forms at the helium/hydrogen interface in the progenitor. If the resulting super-Eddington accretion drives an outflow which thermalizes in the outgoing ejecta, the supernova debris will be re-energized at a time when photons can diffuse out efficiently. The resulting light curves are different and more diverse than previous fallback supernova models which ignored the input of accretion power and produced short-lived, dim transients. The possible outcomes when fallback accretion power is significant include super-luminous ({approx}> 10{sup 44} erg s{sup -1}) Type II events of both short and long durations, as well as luminous Type I events from compact stars that may have experienced significant mass loss. Accretion power may unbind the remaining infalling material, causing a sudden decrease in the brightness of some long duration Type II events. This scenario may be relevant for explaining some of the recently discovered classes of peculiar and rare supernovae.

  7. Hazard Classification for Fuel Supply Shutdown Facility

    SciTech Connect (OSTI)

    BENECKE, M.W.

    2000-09-07T23:59:59.000Z

    Final hazard classification for the 300 Area N Reactor fuel storage facility resulted in the assignment of Nuclear Facility Hazard Category 3 for the uranium metal fuel and feed material storage buildings (303-A, 303-B, 303-G, 3712, and 3716). Radiological for the residual uranium and thorium oxide storage building and an empty former fuel storage building that may be used for limited radioactive material storage in the future (303-K/3707-G, and 303-E), and Industrial for the remainder of the Fuel Supply Shutdown buildings (303-F/311 Tank Farm, 303-M, 313-S, 333, 334 and Tank Farm, 334-A, and MO-052).

  8. Better Plants Supply Chain Pilot Overview

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureCommentsEnergyand Sustained Coordination BetterBetterTechnicalSUPPLY

  9. U.S. Coal Supply and Demand

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over OurThe Iron Spin Transition in2,EHSS A-Zandofpoint motional%^ U N CU.S. Coal Supply

  10. Paperclips Supply Store Forms | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122Commercial602 1,39732onMakeEducationRemediation » Paducah WastePaperclips Supply

  11. Lab school supply drive starts July 15

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5 - -/e),,s -Labgrants DecisionLab school supply

  12. Sandia Energy - Energy Supply Transformation Needed

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's PossibleRadiationImplementing Nonlinear757 (1)Tara46Energy Storage Systems Permalink GallerySupply

  13. Supplying success | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solid ...Success StoriesSupplement AnalysisSupplying success

  14. Restricted Natural Gas Supply Case (released in AEO2005)

    Reports and Publications (EIA)

    2005-01-01T23:59:59.000Z

    The restricted natural gas supply case provides an analysis of the energy-economic implications of a scenario in which future gas supply is significantly more constrained than assumed in the reference case. Future natural gas supply conditions could be constrained because of problems with the construction and operation of large new energy projects, and because the future rate of technological progress could be significantly lower than the historical rate. Although the restricted natural gas supply case represents a plausible set of constraints on future natural gas supply, it is not intended to represent what is likely to happen in the future.

  15. INFLUENCE OF SUPPLY AIR TEMPERATURE ON UNDERFLOOR AIR DISTRIBUTION (UFAD) SYSTEM ENERGY PERFORMANCE

    E-Print Network [OSTI]

    2012-01-01T23:59:59.000Z

    chilled water cooling coil, and supply fan. The fan is aspecify the VAV box cooling design supply air temperature (the underfloor supply plenum (thereby, reducing room cooling

  16. A Fuel Cell Power Supply for Long Duration Balloon Flights Using Stored Cryogens

    E-Print Network [OSTI]

    Green, Michael A.; Manikowski, A.; Noland, G.; Golden, R.L.

    1997-01-01T23:59:59.000Z

    CA, (1966) LBNL-40618 A FUEL CELL POWER SUPPLY FOR LONGLBNL-40618 A FUEL CELL POWER SUPPLY FOR LONG DURATIONreport describes a fuel cell power supply configuration.

  17. High energy density lithium-oxygen secondary battery

    SciTech Connect (OSTI)

    Sammells, A.F.

    1989-02-07T23:59:59.000Z

    A high energy density lithium-oxygen secondary cell is described comprising a lithium-containing negative electrode; a lithium ion conducting molten salt electrolyte contacting the negative electrode; an oxygen ion conducting solid electrolyte contacting and containing the molten salt electrolyte; and an oxygen redox positive electrode contacting the oxygen ion conducting solid electrolyte.

  18. Energetic neutral atoms at Mars 4. Imaging of planetary oxygen

    E-Print Network [OSTI]

    Lukyanov, Alex

    Energetic neutral atoms at Mars 4. Imaging of planetary oxygen S. Barabash and M. Holmstro of the Martian oxygen exosphere/corona results in the production of planetary oxygen ions. The newborn ions start. The oxygen ions can then charge exchange with the neutral gases (H, H2, and O) of the Martian exosphere

  19. Oxygen Toxicity Calculations by Erik C. Baker, P.E.

    E-Print Network [OSTI]

    Read, Charles

    1 Oxygen Toxicity Calculations by Erik C. Baker, P.E. Management of exposure to oxygen toxicity myself using the good ole' FORTRAN programming language, I found that incorporating oxygen toxicity for others. Background Two oxygen toxicity parameters are typically "tracked" in technical diving

  20. CBTL Design Case Summary Conventional Feedstock Supply System - Herbaceous

    SciTech Connect (OSTI)

    Christopher T. Wright; Erin M. Searcy

    2012-02-01T23:59:59.000Z

    A conventional bale feedstock design has been established that represents supply system technologies, costs, and logistics that are achievable today for supplying herbaceous feedstocks as a blendstock with coal for energy production. Efforts are made to identify bottlenecks and optimize the efficiency and capacities of this supply system, within the constraints of existing local feedstock supplies, equipment, and permitting requirements. The feedstock supply system logistics operations encompass all of the activities necessary to move herbaceous biomass feedstock from the production location to the conversion reactor ready for blending and insertion. This supply system includes operations that are currently available such that costs and logistics are reasonable and reliable. The system modeled for this research project includes the uses of field-dried corn stover or switchgrass as a feedstock to annually supply an 800,000 DM ton conversion facility.

  1. Oxygen-Reducing Biocathodes Operating with Passive Oxygen Transfer in Microbial Fuel Cells

    E-Print Network [OSTI]

    Oxygen-Reducing Biocathodes Operating with Passive Oxygen Transfer in Microbial Fuel Cells Xue Xia, Justin C. Tokash, Fang Zhang, Peng Liang, Xia Huang,*, and Bruce E. Logan*,, State Key Joint Laboratory of Environment Simulation and Pollution Control, School of Environment, Tsinghua University, Beijing 100084, P

  2. Gas energy supply outlook through 2010

    SciTech Connect (OSTI)

    Kalisch, R.B.

    1986-03-01T23:59:59.000Z

    Late in 1984 the American Gas Association published a study by the Gas Supply Committee titled, ''The Outlook for Gas Energy Through 2010.'' This study was a joint effort by many people of the gas industry including GRI, IGT and AGA. The study observed that come 1646 Tcf of natural gas is judged to be ultimately recoverable in the US. Of this total, 665 Tcf were produced up to year-end 1984. At that time an additional 197 Tcf were categorized as proved reserves, i.e., known to exist with reasonable certainty and producible under current economic and operating conditions. An additional 784 Tcf were classified as potential supply. In short, about 60 % of the nation's ultimately recoverable resource still is available; only 40 % has been produced to data. This is a formidable gas resource for the lower-48; in 1984 the production level was about 17 Tcf; proved reserves were approximately 163 Tcf - more than nine times the 1984 production. 2 references, 2 tables.

  3. SPEAR3 LARGE DC MAGNET POWER SUPPLIES

    SciTech Connect (OSTI)

    de Lira, A

    2004-06-23T23:59:59.000Z

    The Stanford Synchrotron Radiation Laboratory (SSRL) has successfully commissioned SPEAR3, its newly upgraded 3-GeV synchrotron light source. First stored beam occurred December 15, 2003 and 100mA operation was reached on January 20, 2004. This paper describes the specification, design, and performance of the SPEAR3 DC magnet large power supplies (LGPS) that consist of tightly-regulated (better than {+-}10 ppm) current sources ranging from 100A to 225A and output powers ranging from 70kW to 135kW. A total of 6 LGPS are in successful operation and are used to power strings of quadrupoles and sextupoles. The LGPS are isolated by a delta/delta-wye 60Hz step-down transformer that provides power to 2 series-connected chopper stages operating phase-shifted at a switching frequency of 18-kHz to provide for fast output response and high efficiency. Also described are outside procurement aspects, installation, in-house testing, and operation of the power supplies.

  4. High performance magnet power supply optimization

    SciTech Connect (OSTI)

    Jackson, L.T.

    1988-01-01T23:59:59.000Z

    The power supply system for the joint LBL--SLAC proposed accelerator PEP provides the opportunity to take a fresh look at the current techniques employed for controlling large amounts of dc power and the possibility of using a new one. A basic requirement of +- 100 ppM regulation is placed on the guide field of the bending magnets and quadrupoles placed around the 2200 meter circumference of the accelerator. The optimization questions to be answered by this paper are threefold: Can a firing circuit be designed to reduce the combined effects of the harmonics and line voltage combined effects of the harmonics and line voltage unbalance to less than 100 ppM in the magnet field. Given the ambiguity of the previous statement, is the addition of a transistor bank to a nominal SCR controlled system the way to go or should one opt for an SCR chopper system running at 1 KHz where multiple supplies are fed from one large dc bus and the cost--performance evaluation of the three possible systems.

  5. LNG links remote supplies and markets

    SciTech Connect (OSTI)

    Avidan, A.A.; Gardner, R.E.; Nelson, D.; Borrelli, E.N. [Mobil LNG Inc., Houston, TX (United States); Rethore, T.J. [Arthur D. Little Inc., Houston, TX (United States)

    1997-06-02T23:59:59.000Z

    Liquefied natural gas (LNG) has established a niche for itself by matching remote gas supplies to markets that both lacked indigenous gas reserves and felt threatened in the aftermath of the energy crises of the 1970s and 1980s. It has provided a cost-effective energy source for these markets, while also offering an environmentally friendly fuel long before that was fashionable. The introduction of natural-gas use via LNG in the early years (mostly into France and Japan) has also allowed LNG to play a major role in developing gas infrastructure. Today, natural gas, often supplied as LNG, is particularly well-suited for use in the combined cycle technology used in independent power generation projects (IPPs). Today, LNG players cannot simply focus on monetizing gas resources. Instead, they must adapt their projects to meet the needs of changing markets. The impact of these changes on the LNG industry has been felt throughout the value chain from finding and producing gas, gas treatment, liquefaction, transport as a liquid, receiving terminals and regasification, and finally, to consumption by power producers, industrial users, and households. These factors have influenced the evolution of the LNG industry and have implications for the future of LNG, particularly in the context of worldwide natural gas.

  6. Oxygenates du`jour...MTBE? Ethanol? ETBE?

    SciTech Connect (OSTI)

    Wolfe, R.

    1995-12-31T23:59:59.000Z

    There are many different liquids that contain oxygen which could be blended into gasoline. The ones that have been tried and make the most sense are in the alcohol (R-OH) and ether (R-O-R) chemical family. The alcohols considered are: methanol (MeOH), ethanol (EtOH), tertiary butyl alcohol (TBA). The ethers are: methyl tertiary butyl ether (MTBE), ethyl tertiary butyl ether (ETBE), tertiary amyl methyl ether (TAME), tertiary amyl ethyl ether (TAEE), di-isopropyl ether (DIPE). Of the eight oxygenates listed above, the author describes the five that are still waiting for widespread marketing acceptance (methanol, TBA, TAME, TAEE, and DIPE). He then discusses the two most widely used oxygenates in the US, MTBE and ethanol, along with the up-and-coming ethanol ether, ETBE. Selected physical properties for all of these oxygenates can be found in Table 2 at the end of this paper. A figure shows a simplified alcohol/ether production flow chart for the oxygenates listed above and how they are interrelated.

  7. On the solar nickel and oxygen abundances

    E-Print Network [OSTI]

    Pat Scott; Martin Asplund; Nicolas Grevesse; A. Jacques Sauval

    2009-01-27T23:59:59.000Z

    Determinations of the solar oxygen content relying on the neutral forbidden transition at 630 nm depend upon the nickel abundance, due to a Ni I blend. Here we rederive the solar nickel abundance, using the same ab initio 3D hydrodynamic model of the solar photosphere employed in the recent revision of the abundances of C, N, O and other elements. Using 17 weak, unblended lines of Ni I together with the most accurate atomic and observational data available we find log epsilon_Ni = 6.17 +/- 0.02 (statistical) +/- 0.05 (systematic), a downwards shift of 0.06 to 0.08 dex relative to previous 1D-based abundances. We investigate the implications of the new nickel abundance for studies of the solar oxygen abundance based on the [O I] 630 nm line in the quiet Sun. Furthermore, we demonstrate that the oxygen abundance implied by the recent sunspot spectropolarimetric study of Centeno & Socas-Navarro needs to be revised downwards from log epsilon_O = 8.86 +/- 0.07 to 8.71 +/- 0.10. This revision is based on the new nickel abundance, application of the best available gf-value for the 630 nm forbidden oxygen line, and a more transparent treatment of CO formation. Determinations of the solar oxygen content relying on forbidden lines now appear to converge around log epsilon_O = 8.7.

  8. OXYGEN ENHANCED COMBUSTION FOR NOx CONTROL

    SciTech Connect (OSTI)

    David R. Thompson; Lawrence E. Bool; Jack C. Chen

    2003-04-01T23:59:59.000Z

    This quarterly technical progress report will summarize work accomplished for the Program through the twelfth quarter, January-March 2003, in the following task areas: Task 1--Oxygen Enhanced Combustion, Task 2--Oxygen Transport Membranes, Task 3--Economic Evaluation and Task 4--Program Management. The program is proceeding in accordance with the objectives for the third year. Pilot scale experiments conducted at the University of Utah explored both the effectiveness of oxygen addition and the best way to add oxygen with a scaled version of Riley Power's newest low NOx burner design. CFD modeling was done to compare the REI's modeling results for James River Unit 3 with the NOx and LOI results obtained during the demonstration program at that facility. Investigation of an alternative method of fabrication of PSO1d elements was conducted. OTM process development work has concluded with the completion of a long-term test of a PSO1d element Economic evaluation has confirmed the advantage of oxygen-enhanced combustion. Proposals have been submitted for two additional beta test sites. Commercial proposals have been submitted. Economic analysis of a beta site test performance was conducted.

  9. OXYGEN ENHANCED COMBUSTION FOR NOx CONTROL

    SciTech Connect (OSTI)

    David R. Thompson; Lawrence E. Bool; Jack C. Chen

    2003-02-01T23:59:59.000Z

    This quarterly technical progress report will summarize work accomplished for the Program through the eleventh quarter, October-December 2002, in the following task areas: Task 1 - Oxygen Enhanced Combustion, Task 2 - Oxygen Transport Membranes, Task 3 - Economic Evaluation and Task 4 - Program Management. The program is proceeding in accordance with the objectives for the third year. Pilot scale experiments conducted at the University of Utah were aimed at confirming the importance of oxygen injection strategy for different types of burners. CFD modeling at REI was used to better understand the potential for increased corrosion under oxygen enhanced combustion conditions. Data from a full-scale demonstration test in Springfield, MO were analyzed. OTM element development continued with preliminary investigation of an alternative method of fabrication of PSO1d elements. OTM process development continued with long-term testing of a PSO1d element. Economic evaluation has confirmed the advantage of oxygen-enhanced combustion. Proposals have been submitted for two additional beta test sites. A first commercial proposal has been submitted. Economic analysis of a beta site test performance was conducted.

  10. Oxygen abundance of open cluster dwarfs

    E-Print Network [OSTI]

    Z. -X. Shen; X. -W. Liu; H. -W. Zhang; B. Jones; D. N. C. Lin

    2007-03-30T23:59:59.000Z

    We present oxygen abundances of dwarfs in the young open cluster IC 4665 deduced from the OI $\\lambda$7774 triplet lines and of dwarfs in the open cluster Pleiades derived from the [OI] $\\lambda$6300 forbidden line. Stellar parameters and oxygen abundances were derived using the spectroscopic synthesis tool SME (Spectroscopy Made Easy). We find a dramatic increase in the upper boundary of the OI triplet abundances with decreasing temperature in the dwarfs of IC 4665, consistent with the trend found by Schuler et al. in the open clusters Pleiades and M 34, and to a less extent in the cool dwarfs of Hyades (Schuler et al. 2006a) and UMa (King & Schuler 2005). By contrast, oxygen abundances derived from the [OI] $\\lambda$6300 forbidden line for stars in Pleiades and Hyades (Schuler et al. 2006b) are constant within the errors. Possible mechanisms that may lead a varying oxygen triplet line abundance are examined, including systematic errors in the stellar parameter determinations, the NLTE effects, surface activities and granulation. The age-related effects stellar surface activities (especially the chromospheric activities) are suggested by our analysis to blame for the large spreads of oxygen triplet line abundances.

  11. Construction of Fractal Surfaces by Recurrent Fractal Interpolation Curves

    E-Print Network [OSTI]

    Chol-hui Yun; Hyong-chol O.; Hui-chol Choi

    2014-08-12T23:59:59.000Z

    A method to construct fractal surfaces by recurrent fractal curves is provided. First we construct fractal interpolation curves using a recurrent iterated functions system(RIFS) with function scaling factors and estimate their box-counting dimension. Then we present a method of construction of wider class of fractal surfaces by fractal curves and Lipschitz functions and calculate the box-counting dimension of the constructed surfaces. Finally, we combine both methods to have more flexible constructions of fractal surfaces.

  12. Oxygen: From Environment to Genes. The periodic occurrence of oxygen minima can powerfully influence organisms living in near

    E-Print Network [OSTI]

    Oxygen: From Environment to Genes. The periodic occurrence of oxygen minima can powerfully to the winter of 2014. Their scholarly work is presented in this collection. #12;1 Oxygen: From Environment", 2013, 2014 Table of contents Page 2. Laura Lilly - Low-oxygen formation along the California current. 6

  13. Impact of the renewable oxygenate standard for reformulated gasoline on ethanol demand, energy use, and greenhouse gas emissions

    SciTech Connect (OSTI)

    Stork, K.C.; Singh, M.K.

    1995-04-01T23:59:59.000Z

    To assure a place for renewable oxygenates in the national reformulated gasoline (RFG) program, the US Environmental Protection Agency has promulgated the renewable oxygenate standard (ROS) for RFG. It is assumed that ethanol derived from corn will be the only broadly available renewable oxygenate during Phase I of the RFG program. This report analyzes the impact that the ROS could have on the supply of ethanol, its transported volume, and its displacement from existing markets. It also considers the energy and crude oil consumption and greenhouse gas (GHG) emissions that could result from the production and use of various RFGs that could meet the ROS requirements. The report concludes that on the basis of current and projected near-term ethanol capacity, if ethanol is the only available renewable oxygenate used to meet the requirements of the ROS, diversion of ethanol from existing use as a fuel is likely to be necessary. Year-round use of ethanol and ETBE would eliminate the need for diversion by reducing winter demand for ethanol. On an RFG-program-wide basis, using ethanol and ETBE to satisfy the ROS can be expected to slightly reduce fossil energy use, increase crude oil use, and have essentially no effect on GHG emissions or total energy use relative to using RFG oxygenated only with MTBE.

  14. Supply Chain The effective supply chain has become a new organizational and operational

    E-Print Network [OSTI]

    Lin, Xiaodong

    and operational model for the information age. Supply chain management is a business process that enables a virtual integration of business partners to achieve new levels of efficiency and productivity, as well cutting-edge research and serves as a valuable business resource. The Rutgers Reputation Rutgers Business

  15. Introduction The Sustainable Supply Chain Taxes Permits Integration Future Research Sustainable Supply Chains

    E-Print Network [OSTI]

    Nagurney, Anna

    Supply Chains: Multicriteria Decision-Making and Policy Analysis for the Environment Trisha D. Woolley into the atmosphere, through the combustion of fossil fuels (coal, oil, and natural gas), has risen 30% in the 200) with 11 of the 12 warmest years occurring between 1995­2006 (IPCC (2007)). In the US alone, greenhouse gas

  16. A Curved Boundary Treatment for Discontinuous Galerkin Schemes ...

    E-Print Network [OSTI]

    2015-03-09T23:59:59.000Z

    memory costs in curved elements will be increased due to integration on ...... Optimal energy conserving local ... Springer Science & Business Media, 2009. 23

  17. THE CENTRAL CURVE IN LINEAR PROGRAMMING 1. Introduction ...

    E-Print Network [OSTI]

    2010-12-17T23:59:59.000Z

    Section 2 offers an analysis of central curves in the plane, with emphasis on the dual ...... path is generated by the circuit polynomials (21) and the d linear ...

  18. Semistable Models of Curves Resolution of singularities on the tower of modular

    E-Print Network [OSTI]

    Semistable Models of Curves Resolution of singularities on the tower of modular curves Jared on the tower of modular curves #12;Semistable Models of Curves Semistable models: Definition Let R Resolution of singularities on the tower of modular curves #12;Semistable Models of Curves Semistable models

  19. The oxygen abundance deficiency in irregular galaxies

    E-Print Network [OSTI]

    L. S. Pilyugin; F. Ferrini

    2000-01-05T23:59:59.000Z

    The observed oxygen abundances in a number of irregular galaxies have been compared with predictions of the closed-box model of chemical and photometric evolution of galaxies. Oxygen is found to be deficient with respect to the predicted abundances. This is an indicator in favor of loss of heavy elements via galactic winds or/and of infall of low--abundance gas onto the galaxy. The oxygen abundance deficiency observed within the optical edge of a galaxy cannot be explained by mixing with the gas envelope observed outside the optical limit. We confirm the widespread idea that a significant part of the heavy elements is ejected by irregular galaxies in the intergalactic medium.

  20. Photochemical Escape of Oxygen from Early Mars

    E-Print Network [OSTI]

    Zhao, Jinjin

    2015-01-01T23:59:59.000Z

    Photochemical escape is an important process for oxygen escape from present Mars. In this work, a 1-D Monte-Carlo Model is developed to calculate escape rates of energetic oxygen atoms produced from O2+ dissociative recombination reactions (DR) under 1, 3, 10, and 20 times present solar XUV fluxes. We found that although the overall DR rates increase with solar XUV flux almost linearly, oxygen escape rate increases from 1 to 10 times present solar XUV conditions but decreases when increasing solar XUV flux further. Analysis shows that atomic species in the upper thermosphere of early Mars increases more rapidly than O2+ when increasing XUV fluxes. While the latter is the source of energetic O atoms, the former increases the collision probability and thus decreases the escape probability of energetic O. Our results suggest that photochemical escape be a less important escape mechanism than previously thought for the loss of water and/or CO2 from early Mars.