Powered by Deep Web Technologies
Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Emissions of Polychlorinated Dibenzodioxins and Dibenzofurans and Polychlorinated Biphenyls from Uncontrolled Burning of Garden and Domestic Waste (Backyard Burning)  

Science Journals Connector (OSTI)

Straw and plastic (polyethylene) film used for wrapping silage were included, since burnings of these wastes on agricultural fields is considered to be one of the most common types of uncontrolled waste combustions in Sweden. ... To obtain fundamental information on dioxin emissions from an open burning 8 wastes which were likely amenable to be burnt wildly or suspected to generate high levels of dioxins were subjected to an open burning simulation in a special adapted furnace. ... designed to simulate waste generated by a "recycling" and a "nonrecycling" family in a 208-L (55-gal) burn barrel at the EPA's Open Burning Test Facility. ...

Björn Hedman; Morgan Näslund; Calle Nilsson; Stellan Marklund

2005-10-13T23:59:59.000Z

2

EIA - Greenhouse Gas Emissions - Nitrous Oxide Emissions  

Gasoline and Diesel Fuel Update (EIA)

4. Nitrous Oxide Emissions 4. Nitrous Oxide Emissions 4.1 Total emissions U.S. nitrous oxide emissions in 2009 were 4 MMTCO2e (1.7 percent) below their 2008 total (Table 22). Sources of U.S. nitrous oxide emissions include agriculture, energy use, industrial processes, and waste management (Figure 22). The largest source is agriculture (73 percent), and the majority of agricultural emissions result from nitrogen fertilization of agricultural soils (87 percent of the agriculture total) and management of animal waste (13 percent). U.S. nitrous oxide emissions rose from 1990 to 1994, fell from 1994 to 2002, and returned to an upward trajectory from 2003 to 2007, largely as a result of increased use of synthetic fertilizers. Fertilizers are the primary contributor of emissions from nitrogen fertilization of soils, which grew by more than 30 percent from

3

Nitrogen Oxides Emission Control Options  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Nitrogen Nitrogen Oxides Emission Control Options for Coal-Fired Electric Utility Boilers Ravi K. Srivastava and Robert E. Hall U.S. Environmental Protection Agency, National Risk Management Research Laboratory, Air Pollution Prevention and Control Division, Research Triangle Park, NC Sikander Khan and Kevin Culligan U.S. Environmental Protection Agency, Office of Air and Radiation, Clean Air Markets Division, Washington, DC Bruce W. Lani U.S. Department of Energy, National Energy Technology Laboratory, Environmental Projects Division, Pittsburgh, PA ABSTRACT Recent regulations have required reductions in emissions of nitrogen oxides (NO x ) from electric utility boilers. To comply with these regulatory requirements, it is increas- ingly important to implement state-of-the-art NO x con- trol technologies on coal-fired utility boilers. This paper reviews NO x control

4

Hardcopy Uncontrolled NOAA NESDIS  

E-Print Network [OSTI]

Interface Control Document IPT Integrated Product Team NESDIS National Environmental Satellite, DataHardcopy Uncontrolled NOAA NESDIS CENTER for SATELLITE APPLICATIONS and RESEARCH DOCUMENT GUIDELINE DG-9.2 TEST READINESS DOCUMENT GUIDELINE Version 3.0 #12;NOAA NESDIS STAR DOCUMENT GUIDELINE DG-9

Kuligowski, Bob

5

Nitrous Oxide Emissions from a Municipal Landfill  

Science Journals Connector (OSTI)

Nitrous Oxide Emissions from a Municipal Landfill ... Due to the small area of landfills as compared to other land-use classes, the total N2O emissions from landfills are estimated to be of minor importance for the total emissions from Finland. ...

Janne Rinne; Mari Pihlatie; Annalea Lohila; Tea Thum; Mika Aurela; Juha-Pekka Tuovinen; Tuomas Laurila; Timo Vesala

2005-09-21T23:59:59.000Z

6

Effects of Diesel Exhaust Emissions on Soot Oxidation and DPF...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Diesel Exhaust Emissions on Soot Oxidation and DPF Regeneration Effects of Diesel Exhaust Emissions on Soot Oxidation and DPF Regeneration DPF regeneration experiments verified the...

7

Nitrogen oxides emission trends in Monthly emission estimates of nitrogen oxides from space provide  

E-Print Network [OSTI]

Chapter 5 Nitrogen oxides emission trends in East Asia Abstract Monthly emission estimates present first results of a new emission estimation algorithm, specifically designed to use daily satellite observations of column concentrations for fast updates of emission estimates of short-lived atmospheric

Haak, Hein

8

Reducing Diesel Engine Emissions  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Reducing Reducing Diesel Engine Emissions 2 0 1 0 Green TransporTaTion TechnoloGies Compared to traditional gasoline engines, diesel engines require less maintenance, generate energy more efficiently, and produce less carbon dioxide emissions. But when uncontrolled, diesel engines churn out harmful emissions like particu- late matter (PM) and nitrogen oxides (NO x ). Researchers at Argonne National Laboratory are currently working to develop

9

Influence of reduced carbon emissions and oxidation on the distribution of atmospheric CO 2 : Implications for inversion analyses  

E-Print Network [OSTI]

Influence of reduced carbon emissions and oxidation on thedescription of reduced carbon emission and oxidationInfluence of reduced carbon emissions and oxidation on the

Suntharalingam, Parvadha; Randerson, James T; Krakauer, Nir; Logan, Jennifer A; Jacob, Daniel J

2005-01-01T23:59:59.000Z

10

Nitrogen oxide emissions from a kraft recovery furnace  

SciTech Connect (OSTI)

Nitrogen Oxide (NOx) emissions from a rebuilt kraft recovery furnace slightly exceeded the specified limit of 1.1 lb/ton (0.55 kg/metric ton) of black-liquor solids. Mill trials were undertaken to determine whether NOx emissions could be minimized by modifying furnace operation. NOx emissions increased when secondary air was shifted to tertiary ports. NOx emissions fell when the amounts of primary and total air were decreased, but this increased emissions of other pollutants. After demonstrating that best operation of the furnace could not meet the permit with an emissions limit that matched the furnace's performance at best operation.

Prouty, A.L.; Stuart, R.C. (James River Corp., Camas, WA (United States)); Caron, A.L. (NCASI West Coast Regional Office, Corvallis, OR (United States))

1993-01-01T23:59:59.000Z

11

Nitrous oxide emissions from wastewater treatment processes  

Science Journals Connector (OSTI)

...specific ammonia oxidation rate. Symbols represent...Research Council (ARC) for funding this...correlated to its ammonia oxidation rate. 51 Arp, D...1146/annurev.micro.61.080706.093449...1146/annurev.micro.61.080706.093449...2004 Anaerobic oxidation of inorganic nitrogen...

2012-01-01T23:59:59.000Z

12

Nitrogen Oxide Emission Statements (Ohio) | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Nitrogen Oxide Emission Statements (Ohio) Nitrogen Oxide Emission Statements (Ohio) Nitrogen Oxide Emission Statements (Ohio) < Back Eligibility Agricultural Commercial Construction Fuel Distributor Industrial Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Ohio Program Type Environmental Regulations Provider Ohio Environmental Protection Agency This chapter of the law establishes that the Ohio Environmental Protection Agency requires any facility that emits 25 tons or more of NOx and/or 25 tons or more of VOC during the calendar year and is located in a county designated as nonattainment for the National Ambient Air Quality Standards for ozone submit emission statements. Any facility that is located in a county described above is exempt from these requirements. If NOx

13

Effects of Diesel Exhaust Emissions on Soot Oxidation and DPF Regeneration  

Broader source: Energy.gov [DOE]

DPF regeneration experiments verified the effects of NO2 and O2 emissions found from the thermogravimetric analyzer soot oxidation.

14

MODELING THE EMISSIONS OF NITROUS OXIDE (N20) AND METHANE (CH 4) FROM THE  

E-Print Network [OSTI]

MODELING THE EMISSIONS OF NITROUS OXIDE (N20) AND METHANE (CH 4) FROM THE TERRESTRIAL BIOSPHERE;2 #12;MODELING THE EMISSIONS OF NITROUS OXIDE (N 20) AND METHANE (CH 4) FROM THE TERRESTRIAL BIOSPHERE cli- mate has on natural emissions of N2 0 and CH4 from the terrestrial biosphere to the atmosphere

15

Reduction of carbon monoxide emissions with regenerative thermal oxidizers  

SciTech Connect (OSTI)

Regenerative thermal oxidizers (RTOs) have been extensively used for the control of volatile organic compound (VOC) emissions from various sources. However, very little information is available on the ability of RTOs to control carbon monoxide (CO) emissions. This paper presents the results of extensive tests conducted on two RTOs to determine their VOC and CO control efficiencies. The inlet gas stream to the RTOs includes VOC and CO concentrations as high as 2,000 ppm and 3,600 ppm, respectfully. The testing demonstrated that both RTOs were capable of controlling greater than 98% of both inlet VOCs and CO. While the destruction efficiencies within the combustion chambers exceeded 99.9%, direct leakage past valves accounted for the lower control efficiencies. The tests indicated that the overall VOC and CO control efficiencies of the RTOs may be limited by valve leakage. The design and permitting of a RTO should include conservative control estimates which account for possible valve leakage.

Firmin, S.M.; Lipke, S.; Baturay, A.

1996-09-01T23:59:59.000Z

16

Low-Temperature Hydrocarbon/CO Oxidation Catalysis in Support of HCCI Emission Control  

Broader source: Energy.gov [DOE]

Development of catalyst materials to facilitate the low-temperature oxidation of hydrocarbons and CO in homogeneous charge compression ignition (HCCI) emissions.

17

Nitric oxide emissions from the high-temperature viscous boundary layers of hypersonic aircraft within the stratosphere  

SciTech Connect (OSTI)

The authors study the nitric oxide emission characteristics of supersonic aircraft resulting from heating of viscous boundary layers along the skin of the aircraft. Previous study has concentrated on nitric oxide emissions coming from combustion products from the scramjet engines. This work shows that above mach 8, emissions from viscous heating become a significant factor in total emission of nitric oxide. Above mach 16 it becomes the dominant source of emission.

Brooks, S.B.; Lewis, M.J.; Dickerson, R.R. [Univ. of Maryland, College Park, MD (United States)

1993-09-20T23:59:59.000Z

18

Oxides Emissions from Coal-Fired Boilers TOPICAL REPORT NUMBER 14  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Reburning Technologies for the Control of Nitrogen Reburning Technologies for the Control of Nitrogen Oxides Emissions from Coal-Fired Boilers TOPICAL REPORT NUMBER 14 MAY 1999 TOPICAL REPORT NUMBER 14 A report on three projects conducted under separate cooperative agreements between: The U.S. Department of Energy and * The Babcock & Wilcox Company * Energy and Environmental Research Corporation * New York State Electric & Gas Corporation MAY 1999 Reburning Technologies for the Control of Nitrogen Oxides Emissions from Coal-Fired Boilers Cover image: Schematic of reburning technology Source: Energy and Environmental Research Corporation Reburning Technologies for the Control of Nitrogen Oxides Emissions from Coal-Fired Boilers Executive Summary ..................................................................................................

19

Process Modeling of Global Soil Nitrous Oxide Emissions  

E-Print Network [OSTI]

Nitrous oxide is an important greenhouse gas and is a major ozone-depleting substance. To understand and

Saikawa, E.

2011-09-01T23:59:59.000Z

20

Methods of reducing emissions of nitrogen oxides at thermal power plants burning solid domestic waste  

Science Journals Connector (OSTI)

Essentially all the major methods of reducing the emissions of nitrogen oxides from flue gases employed in power generation have been tested on plants in Moscow which burn solid domestic waste for production of h...

A. N. Tugov; V. F. Moskvichev

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

NETL: Mercury Emissions Control Technologies - Oxidation of Mercury Across  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Oxidation of Mercury Across SCR Catalysts in Coal-Fired Power Plants Burning Low Rank Fuels Oxidation of Mercury Across SCR Catalysts in Coal-Fired Power Plants Burning Low Rank Fuels The objective of the proposed research is to assess the potential for the oxidation of mercury in flue gas across SCR catalysts in a coal fired power plant burning low rank fuels using a slipstream reactor containing multiple commercial catalysts in parallel. Results from the project will contribute to a greater understanding of mercury behavior across SCR catalysts. Additional tasks include: review existing pilot and field data on mercury oxidation across SCR catalysts and propose a mechanism for mercury oxidation and create a simple computer model for mercury oxidation based on the hypothetical mechanism. Related Papers and Publications: Final Report - December 31, 2004 [PDF-532KB]

22

Influence of reduced carbon emissions and oxidation on the distribution of atmospheric CO2: Implications for inversion analyses  

E-Print Network [OSTI]

Influence of reduced carbon emissions and oxidation on the distribution of atmospheric CO2 carbon emissions. We used TransCom3 annual mean simulations from three transport models to evaluate carbon emission and oxidation processes in deriving inversion estimates of CO2 surface fluxes. Citation

Krakauer, Nir Y.

23

Lessons from Loscoe: the uncontrolled migration of landfill gas  

Science Journals Connector (OSTI)

...the uncontrolled migration of landfill gas G. M. Williams 1 N. Aitkenhead...Environment, 1989. The Control of Landfill Gas. HMSO, London. Doelle, H...1988. Trace constituents in landfill gas. Gas Research Institute. Frost...

G. M. Williams; N. Aitkenhead

24

Effectiveness of Diesel Oxidation Catalyst in Reducing HC and CO Emissions from Reactivity Controlled Compression Ignition  

SciTech Connect (OSTI)

Reactivity Controlled Compression Ignition (RCCI) has been shown to allow for diesel-like or better brake thermal efficiency with significant reductions in nitrogen oxide (NOX) particulate matter (PM) emissions. Hydrocarbon (HC) and carbon monoxide (CO) emission levels, on the other hand, are similar to those of port fuel injected gasoline engines. The higher HC and CO emissions combined with the lower exhaust temperatures with RCCI operation present a challenge for current exhaust aftertreatments. The reduction of HC and CO emissions in a lean environment is typically achieved with an oxidation catalyst. In this work, several diesel oxidation catalysts (DOC) with different precious metal loadings were evaluated for effectiveness to control HC and CO emissions from RCCI combustion in a light-duty multi-cylinder engine operating on gasoline and diesel fuels. Each catalyst was evaluated in a steady-state engine operation with temperatures ranging from 160 to 260 C. A shift to a higher light-off temperature was observed during the RCCI operation. In addition to the steady-state experiments, the performances of the DOCs were evaluated during multi-mode engine operation by switching from diesel-like combustion at higher exhaust temperature and low HC/CO emissions to RCCI combustion at lower temperature and higher HC/CO emissions. High CO and HC emissions from RCCI generated an exotherm keeping the catalyst above the light-off temperature.

Prikhodko, Vitaly Y [ORNL; Curran, Scott [ORNL; Parks, II, James E [ORNL; Wagner, Robert M [ORNL

2013-01-01T23:59:59.000Z

25

Modeling of Nitrogen Oxides Emissions from CFB Combustion  

Science Journals Connector (OSTI)

In this work, a simplified description of combustion and nitrogen oxides chemistry was implemented in a 1.5D model framework with the aim to compare the results with ones earlier obtained with a detailed react...

S. Kallio; M. Keinonen

2010-01-01T23:59:59.000Z

26

Persistent sensitivity of Asian aerosol to emissions of nitrogen oxides  

E-Print Network [OSTI]

We use a chemical transport model and its adjoint to examine the sensitivity of secondary inorganic aerosol formation to emissions of precursor trace gases from Asia. Sensitivity simulations indicate that secondary inorganic ...

Kharol, S. K.

27

Analytical Framework to Evaluate Emission Control Systems for Marine Engines.  

E-Print Network [OSTI]

??Emissions from marine diesel engines are mainly uncontrolled and affect regional air quality and health of people living near ports. Many emission control strategies are… (more)

Jayaram, Varalakshmi

2010-01-01T23:59:59.000Z

28

Regional-Scale Assessment of Nitrous Oxide Emissions within the US Corn Belt: The Impact of Precipitation and Agricultural Drainage on Indirect Emissions  

E-Print Network [OSTI]

Regional-Scale Assessment of Nitrous Oxide Emissions within the US Corn Belt: The Impact of Precipitation and Agricultural Drainage on Indirect Emissions Tim Griffis1, Xuhui Lee2, John Baker3, Peter, but mitigation strategies have been limited by the large uncertainties in both direct and indirect emission

Minnesota, University of

29

The reduction of greenhouse gas emissions using various thermal systems in a landfill site  

Science Journals Connector (OSTI)

In this paper, the Greenhouse Gas (GHG) emissions from an uncontrolled landfill site filled with Municipal Solid Waste (MSW) are compared with those from controlled sites in which collected Landfill Gases (LFG) are utilised by various technologies. These technologies include flaring, conventional electricity generation technologies such as Internal Combustion Engine (ICE) and Gas Turbine (GT) and an emerging technology, Solid Oxide Fuel Cell (SOFC). The results show that SOFC is the best option for reducing the GHG emissions among the studied technologies. In the case when SOFC is used, GHG emissions from the controlled site are reduced by 63% compared to the uncontrolled site. This case has a specific lifetime GHG emission of 2.38 tonnes CO2 .eq/MWh when only electricity is produced and 1.12 tonnes CO2.eq/MWh for a cogeneration application.

C. Ozgur Colpan; Ibrahim Dincer; Feridun Hamdullahpur

2009-01-01T23:59:59.000Z

30

CARBON SEQUESTRATION IN ARABLE SOILS IS LIKELY TO INCREASE NITROUS OXIDE EMISSIONS, OFFSETTING  

E-Print Network [OSTI]

CARBON SEQUESTRATION IN ARABLE SOILS IS LIKELY TO INCREASE NITROUS OXIDE EMISSIONS, OFFSETTING in strategies for climate protection. 1. Introduction Carbon sequestration has been highlighted recently concentration of carbon dioxide (CO2) in the atmo- sphere include sequestering carbon (C) in soils

31

Assessment of soil nitrogen oxides emissions and implementation in LOTOS-EUROS  

E-Print Network [OSTI]

the formation and transport of nitrogen dioxide, ozone, particulate matter and other species throughout EuropeAssessment of soil nitrogen oxides emissions and implementation in LOTOS-EUROS Date 18 March 2013, climate and nitrogen availability. Nitrogen availability is in turn determined by N-deposition from

Haak, Hein

32

Inverse modeling of emissions for local photo-oxidant pollution : Testing a new methodology with kriging constraints  

E-Print Network [OSTI]

Inverse modeling of emissions for local photo-oxidant pollution : Testing a new methodology. Abstract For chemistry-transport models operating at regional scales, surface emissions are the input data a methodology to optimize surface emissions at local scale i.e. to compute correction factors for the available

Menut, Laurent

33

Reducing Emissions of a Diesel Engine Using Fumigation Ethanol and a Diesel Oxidation Catalyst  

Science Journals Connector (OSTI)

Reducing Emissions of a Diesel Engine Using Fumigation Ethanol and a Diesel Oxidation Catalyst ... † Department of Mechanical Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China ... In contrast to the conventional approach of using ethanol in spark-ignition engines, this study demonstrates the potential of ethanol utilization in diesel engines using dual-fuel combustion, where ethanol is injected into the intake manifold and diesel ... ...

K. S. Tsang; Z. H. Zhang; C. S. Cheung; T. L. Chan

2010-10-14T23:59:59.000Z

34

Emissions of carbon dioxide, methane and nitrous oxide from soil receiving urban wastewater for maize (Zea mays L.) cultivation  

Science Journals Connector (OSTI)

We investigated how amending maize with wastewater at 120 kg N ha?1 affected crop growth, soil characteristics and emissions of carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) compared to plants ferti...

Fabián Fernández-Luqueño; Verónica Reyes-Varela…

2010-06-01T23:59:59.000Z

35

Process for treating ammonia and nitrite containing waters to prevent nitric oxide emissions therefrom  

SciTech Connect (OSTI)

This patent describes a process for controlling the emission of nitrogen dioxide from, and the amount of one or more organisms, selected from the group consisting of fungi, algae and bacteria, growing in a system for handling a flow of condensate of steam, the condensate containing ammonia, ammonia precursors, or a mixture thereof. It comprises contacting the condensate in a substantially continuous manner with an amount of an oxidizing biocide which substantially prevents the emission of nitrogen dioxide from the condensate handling system but which does not substantially inhibit the growth of the organisms in the condensate handling system; and periodically contacting the condensate with an amount of a second biocide which substantially reduces the amount of the organisms.

Gallup, D.L.; Featherstone, J.L.

1991-07-16T23:59:59.000Z

36

Evaluation of oxides of nitrogen emissions for the purpose of their transient regulation from a direct injection diesel engine  

Science Journals Connector (OSTI)

The concept of defining a regulatory standard for the maximum allowable emissions of oxides of nitrogen (NOx) from a heavy-duty diesel engine on an instantaneous basis is presented. The significance of this concept from a regulatory point of view is the possibility to realise a steady brake specific NOx emissions result independent of the test schedule used. The emissions of oxides of nitrogen from a state-of-the-art direct injection diesel engine have been examined on an integral as well as on an instantaneous basis over the Federal Test Procedure as well as over several other arbitrary transient cycles generated for this study. Three candidate standards of specific NOx emissions have been evaluated on a real-time, continuous basis. These include brake power specific, fuel mass specific, and carbon dioxide mass specific NOx emissions. Retaining the stock engine control module, the carbon dioxide specific emissions of NOx have been shown to be the most uniform, varying only by about 30% of its mean value regardless of the test schedule or engine operation. The instantaneous fuel specific NOx emissions are shown to be relatively less invariant and the least steady are the brake power specific emissions with a coefficient of variation of up to 200%. Advancing injection timing has been shown to have a wide range of authority over the specific emissions of oxides of nitrogen regardless of the units used, when operating at full load in the vicinity of peak torque speeds. The carbon dioxide specific NOx emissions have shown a linear dependence on the power specific emissions, independent of the examined operating conditions. The trade-off between better brake thermal efficiency, lower exhaust gas temperature at advanced timing and lower NOx emissions has also been shown to be independent of the units of the specific standard used.

Yasser Yacoub; Chris Atkinson

2001-01-01T23:59:59.000Z

37

ZERO EMISSION POWER PLANTS USING SOLID OXIDE FUEL CELLS AND OXYGEN TRANSPORT MEMBRANES  

SciTech Connect (OSTI)

Over 16,700 hours of operational experience was gained for the Oxygen Transport Membrane (OTM) elements of the proposed SOFC/OTM zero-emission power generation concept. It was repeatedly demonstrated that OTMs with no additional oxidation catalysts were able to completely oxidize the remaining depleted fuel in a simulated SOFC anode exhaust at an O{sub 2} flux that met initial targets. In such cases, neither residual CO nor H{sub 2} were detected to the limits of the gas chromatograph (<10 ppm). Dried OTM afterburner exhaust streams contained up to 99.5% CO{sub 2}. Oxygen flux through modified OTMs was double or even triple that of the standard OTMs used for the majority of testing purposes. Both the standard and modified membranes in laboratory-scale and demonstration-sized formats exhibited stable performance over extended periods (2300 to 3500 hours or 3 to 5 months). Reactor contaminants, were determined to negatively impact OTM performance stability. A method of preventing OTM performance degradation was developed and proven to be effective. Information concerning OTM and seal reliability over extended periods and through various chemical and thermal shocks and cycles was also obtained. These findings were used to develop several conceptual designs for pilot (10 kWe) and commercial-scale (250 kWe) SOFC/OTM zero emission power generation systems.

G. Maxwell Christie; Troy M. Raybold

2003-06-10T23:59:59.000Z

38

Field emission effects of nitrogenated carbon nanotubes on chlorination and oxidation  

SciTech Connect (OSTI)

With reference to our recent reports [Appl. Phys. Lett. 90, 192107 (2007); Appl. Phys. Lett. 91, 202102 (2007)] about the electronic structure of chlorine treated and oxygen-plasma treated nitrogenated carbon nanotubes (N-CNTs), here we studied the electron field emission effects on chlorination (N-CNT:Cl) and oxidation (N-CNT:O) of N-CNT. A high current density (J) of 15.0 mA/cm{sup 2} has been achieved on chlorination, whereas low J of 0.0052 mA/cm{sup 2} is observed on oxidation compared to J=1.3 mA/cm{sup 2} for untreated N-CNT at an applied electric field E{sub A} of {approx}1.9 V/{mu}m. The turn-on electric field (E{sub TO}) was {approx}0.875. The 1.25 V/{mu}m was achieved for N-CNT:Cl and N-CNT:O, respectively, with respect to E{sub TO}=1.0 V/{mu}m for untreated one. These findings are due to the formation of different bonds with carbon and nitrogen in the N-CNT during the process of chlorine (oxygen)-plasma treatment by the charge transfer, or else that changes the density of free charge carriers and hence enhances (reduces) the field emission properties of N-CNTs:Cl (N-CNTs:O)

Ray, S. C.; Palnitkar, U.; Pao, C. W.; Tsai, H. M.; Pong, W. F.; Lin, I-N. [Department of Physics, Tamkang University, Tamsui 251, Taiwan (China); Papakonstantinou, P. [NRI, School of Electrical and Mechanical Engineering, University of Ulster at Jordanstown, Newtownabbey, County Antrim BT37OQB, Northern Ireland (United Kingdom); Ganguly, Abhijit; Chen, L. C. [Center for Condensed Matter Sciences, National Taiwan University, Taipei 106, Taiwan (China); Chen, K. H. [Institute of Atomic and Molecular Sciences, Academia Sinica, Taipei 106, Taiwan (China)

2008-09-15T23:59:59.000Z

39

Emissivity of Candidate Materials for VHTR Applicationbs: Role of Oxidation and Surface Modification Treatments  

SciTech Connect (OSTI)

The Generation IV (GEN IV) Nuclear Energy Systems Initiative was instituted by the Department of Energy (DOE) with the goal of researching and developing technologies and materials necessary for various types of future reactors. These GEN IV reactors will employ advanced fuel cycles, passive safety systems, and other innovative systems, leading to significant differences between these future reactors and current water-cooled reactors. The leading candidate for the Next Generation Nuclear Plant (NGNP) to be built at Idaho National Lab (INL) in the United States is the Very High Temperature Reactor (VHTR). Due to the high operating temperatures of the VHTR, the Reactor Pressure Vessel (RPV) will partially rely on heat transfer by radiation for cooling. Heat expulsion by radiation will become all the more important during high temperature excursions during off-normal accident scenarios. Radiant power is dictated by emissivity, a material property. The NGNP Materials Research and Development Program Plan [1] has identified emissivity and the effects of high temperature oxide formation on emissivity as an area of research towards the development of the VHTR.

Kumar Sridharan; Todd Allen; Mark Anderson; Guoping Cao; Gerald Kulcinski

2011-07-25T23:59:59.000Z

40

Emissions  

Office of Scientific and Technical Information (OSTI)

the extra emissions that are generated from manufacturing the material used to make CNG tanks); they can amount tc more than 2% of the emissions from 32 the fuel production and...

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Zero Emission Power Plants Using Solid Oxide Fuel Cells and Oxygen Transport Membranes  

SciTech Connect (OSTI)

Siemens Westinghouse Power Corp. (SWPC) is engaged in the development of Solid Oxide Fuel Cell stationary power systems. SWPC has combined DOE Developmental funds with commercial customer funding to establish a record of successful SOFC field demonstration power systems of increasing size. SWPC will soon deploy the first unit of a newly developed 250 kWe Combined Heat Power System. It will generate electrical power at greater than 45% electrical efficiency. The SWPC SOFC power systems are equipped to operate on lower number hydrocarbon fuels such as pipeline natural gas, which is desulfurized within the SOFC power system. Because the system operates with a relatively high electrical efficiency, the CO2 emissions, {approx}1.0 lb CO2/ kW-hr, are low. Within the SOFC module the desulfurized fuel is utilized electrochemically and oxidized below the temperature for NOx generation. Therefore the NOx and SOx emissions for the SOFC power generation system are near negligible. The byproducts of the power generation from hydrocarbon fuels that are released into the environment are CO2 and water vapor. This forward looking DOE sponsored Vision 21 program is supporting the development of methods to capture and sequester the CO2, resulting in a Zero Emission power generation system. To accomplish this, SWPC is developing a SOFC module design, to be demonstrated in operating hardware, that will maintain separation of the fuel cell anode gas, consisting of H2, CO, H2O and CO2, from the vitiated air. That anode gas, the depleted fuel stream, containing less than 18% (H2 + CO), will be directed to an Oxygen Transport Membrane (OTM) Afterburner that is being developed by Praxair, Inc.. The OTM is supplied air and the depleted fuel. The OTM will selectively transport oxygen across the membrane to oxidize the remaining H2 and CO. The water vapor is then condensed from the totally 1.5.DOC oxidized fuel stream exiting the afterburner, leaving only the CO2 in gaseous form. That CO2 can then be compressed and sequestered, resulting in a Zero Emission power generation system operating on hydrocarbon fuel that adds only water vapor to the environment. Praxair has been developing oxygen separation systems based on dense walled, mixed electronic, oxygen ion conducting ceramics for a number of years. The oxygen separation membranes find applications in syngas production, high purity oxygen production and gas purification. In the SOFC afterburner application the chemical potential difference between the high temperature SOFC depleted fuel gas and the supplied air provides the driving force for oxygen transport. This permeated oxygen subsequently combusts the residual fuel in the SOFC exhaust. A number of experiments have been carried out in which simulated SOFC depleted fuel gas compositions and air have been supplied to either side of single OTM tubes in laboratory-scale reactors. The ceramic tubes are sealed into high temperature metallic housings which precludes mixing of the simulated SOFC depleted fuel and air streams. In early tests, although complete oxidation of the residual CO and H2 in the simulated SOFC depleted fuel was achieved, membrane performance degraded over time. The source of degradation was found to be contaminants in the simulated SOFC depleted fuel stream. Following removal of the contaminants, stable membrane performance has subsequently been demonstrated. In an ongoing test, the dried afterburner exhaust composition has been found to be stable at 99.2% CO2, 0.4% N2 and 0.6%O2 after 350 hours online. Discussion of these results is presented. A test of a longer, commercial demonstration size tube was performed in the SWPC test facility. A similar contamination of the simulated SOFC depleted fuel stream occurred and the performance degraded over time. A second test is being prepared. Siemens Westinghouse and Praxair are collaborating on the preliminary design of an OTM equipped Afterburner demonstration unit. The intent is to test the afterburner in conjunction with a reduced size SOFC test module that has the anode gas separati

Shockling, Larry A.; Huang, Keqin; Gilboy, Thomas E. (Siemens Westinghouse Power Corporation); Christie, G. Maxwell; Raybold, Troy M. (Praxair, Inc.)

2001-11-06T23:59:59.000Z

42

Does the location of aircraft nitrogen oxide emissions affect their climate impact?  

E-Print Network [OSTI]

approximately balancing the IRF associated with aviation CO2 emissions (28 mWm�2 yr (TgNO2)�1 ). The overall climate impact of global aviation is often represented by a simple multiplier for CO2 emissions­3% of global anthropogenic CO2 emissions [Lee et al., 2009], yet these emissions fall outside the remit

43

Current emission trends for nitrogen oxides, sulfur dioxide, and volatile organic compounds by month and state: Methodology and results  

SciTech Connect (OSTI)

This report presents estimates of monthly sulfur dioxide (SO{sub 2}), nitrogen oxides (NO{sub x}), and nonmethane voltatile organic compound (VOC) emissions by sector, region, and state in the contiguous United States for the years 1975 through 1988. This work has been funded as part of the National Acid Precipitation Assessment Program`s Emissions and Controls Task Group by the US Department of Energy (DOE) Office of Fossil Energy (FE). The DOE project officer is Edward C. Trexler, DOE/FE Office of Planning and Environment.

Kohout, E.J.; Miller, D.J.; Nieves, L.A.; Rothman, D.S.; Saricks, C.L.; Stodolsky, F.; Hanson, D.A.

1990-08-01T23:59:59.000Z

44

Current emission trends for nitrogen oxides, sulfur dioxide, and volatile organic compounds by month and state: Methodology and results  

SciTech Connect (OSTI)

This report presents estimates of monthly sulfur dioxide (SO{sub 2}), nitrogen oxides (NO{sub x}), and nonmethane voltatile organic compound (VOC) emissions by sector, region, and state in the contiguous United States for the years 1975 through 1988. This work has been funded as part of the National Acid Precipitation Assessment Program's Emissions and Controls Task Group by the US Department of Energy (DOE) Office of Fossil Energy (FE). The DOE project officer is Edward C. Trexler, DOE/FE Office of Planning and Environment.

Kohout, E.J.; Miller, D.J.; Nieves, L.A.; Rothman, D.S.; Saricks, C.L.; Stodolsky, F.; Hanson, D.A.

1990-08-01T23:59:59.000Z

45

Role of the opioid system in the behavioral deficit observed after uncontrollable shock  

E-Print Network [OSTI]

to minimize shock exposure by maintaining a hindlimb in a flexed position. Preexposure to uncontrollable shock (shock independent of leg position) disrupts this learning. Activation of opioid receptors seems to contribute to the expression of the behavioral...

Washburn, Stephanie Nicole

2006-08-16T23:59:59.000Z

46

Air Quality Responses to Changes in Black Carbon and Nitrogen Oxide Emissions  

E-Print Network [OSTI]

D. , (2008a). Carbonyl and nitrogen dioxide emissions fromstudy of indoor nitrogen dioxide levels and respiratoryand modeled nitrogen dioxide (NO 2 ) concentrations. All

Millstein, Dev

2009-01-01T23:59:59.000Z

47

Calculation of the emission of nitrogen oxides in electric resistance heating furnaces  

Science Journals Connector (OSTI)

The present paper is devoted to the least studied topic in the field of use of modern electric heating equipment, namely, pollution of the atmosphere by nitrogen oxides and reduction of the intensity of this e...

A. V. Aksenov; V. A. Belyakov; Z. G. Sadykova

1998-02-01T23:59:59.000Z

48

Low-Temperature Hydrocarbon/CO Oxidation Catalysis in Support of HCCI Emission Control  

Broader source: Energy.gov [DOE]

Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

49

Rational Catalyst Design Applied to Development of Advanced Oxidation Catalysts for Diesel Emission Control  

Broader source: Energy.gov [DOE]

Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

50

Nitrous oxide and carbon dioxide emissions from pelletized and nonpelletized poultry litter incorporated into soil  

Science Journals Connector (OSTI)

While several studies have shown that the addition of animal manures to soil can increase N2O and CO2 emissions, limited information is available on the effect that manure physical characteristics can have on the...

M. L. Cabrera; S. C. Chiang; W. C. Merka; O. C. Pancorbo; S. A. Thompson

51

Ultrafine PM Emissions from Natural Gas, Oxidation-Catalyst Diesel, and Particle-Trap Diesel Heavy-Duty Transit Buses  

Science Journals Connector (OSTI)

In urban areas, transit buses are a significant source of heavy-duty vehicle traffic, and many municipalities, including Los Angeles, Sacramento, Cleveland, and Atlanta, have recently modified their fleets to compressed natural gas (CNG) as the “clean” alternative to conventional uncontrolled diesel vehicles to meet increasingly strict particulate matter (PM) air quality regulations. ... ARB's mission is to promote and protect public health, welfare, and ecological resources through effective reduction of air pollutants while recognizing and considering effects on the economy. ...

Britt A. Holmén; Alberto Ayala

2002-11-05T23:59:59.000Z

52

EMISSIONS OF NITROUS OXIDE AND METHANE FROM CONVENTIONAL AND ALTERNATIVE FUEL MOTOR VEHICLES  

E-Print Network [OSTI]

-produced electricity for battery electric vehicles. Already, vehicles powered by compressed natural gas, propane. LIPMAN AND MARK A. DELUCCHI example, promising strategies for powering motor vehicles with reduced GHGEMISSIONS OF NITROUS OXIDE AND METHANE FROM CONVENTIONAL AND ALTERNATIVE FUEL MOTOR VEHICLES

Kammen, Daniel M.

53

High emissivity coatings on titanium alloy prepared by micro-arc oxidation for high temperature application  

Science Journals Connector (OSTI)

Micro-arc oxidation coatings were prepared on Ti6Al4V alloy in...3PO4-based electrolyte with different additives such as FeSO4, Co(CH3COO)2, Ni(CH3COO)2, and K2ZrF6. The composition, structure, surface morphology...

H. Tang; Q. Sun; C. G. Yi; Z. H. Jiang; F. P. Wang

2012-03-01T23:59:59.000Z

54

Nitrous oxide emissions. Topical report, July 1, 1990--June 30, 1993  

SciTech Connect (OSTI)

Published N{sub 2}O emissions data for experimental studies examining large numbers of coals are generally scarce at the pilot-scale fluidized-bed combustion (FBC) level, although some data are available at the laboratory scale. The primary objective of this study was to determine the atmospheric contribution of N{sub 2}O derived from coal combustion. Additionally, the goal was to establish a comprehensive engineering model to assist in the prediction of N{sub 2}O emissions based upon operating and design considerations. To meet the overall objectives of determining the overall contribution of N{sub 2}O derived from FBC and developing an engineering model seven tasks were originally proposed. The objective of each task as originally proposed and finally executed is presented in this topical report. The seven tasks were: (1) literature survey; (2) equipment design and test plan development; (3) experimental techniques; (4) pilot-scale determination of the impacts of coal properties and operating conditions on N{sub 2}O emissions; (5) role of coal char on N{sub 2}O formation and destruction; (6) homogeneous versus heterogeneous reactions; and (7) modeling of N{sub 2}O emissions.

Collings, M.E.; Mann, M.D.

1993-12-01T23:59:59.000Z

55

Influence of solid fuel on the carbon-monoxide and nitrogen-oxide emissions on sintering  

SciTech Connect (OSTI)

Laboratory and industrial research now underway at the sintering plant of AO Mittal Steel Temirtau is focusing on the preparation of fuel of optimal granulometric composition, the replacement of coke fines, and the adaptation of fuel-input technology so as to reduce fuel consumption and toxic emissions without loss of sinter quality.

M.F. Vitushchenko; N.L. Tatarkin; A.I. Kuznetsov; A.E. Vilkov [AO Mittal Steel Temirtau, Temirtau (Kazakhstan)

2007-07-01T23:59:59.000Z

56

16 - Ultra-low nitrogen oxides (NOx) emissions combustion in gas turbine systems  

Science Journals Connector (OSTI)

Abstract: The historical development of gas turbine low \\{NOx\\} combustion from the pioneering NASA work in the early 1970s to the present generation of ultra-low \\{NOx\\} industrial gas turbine combustors is reviewed. The principles of operation of single digit ultra-low \\{NOx\\} gas turbine combustion for industrial applications are outlined. The review shows the potential has been demonstrated by several investigators using different flame stabilizers for \\{NOx\\} to be reduced to 1 ppm at 1700 K, 2 ppm at 1800 K and 3–4 ppm at 1900 K with no influence of operating pressure and with a practical operating flame stability margin. Under these conditions it is shown that no thermal \\{NOx\\} should occur and all the \\{NOx\\} is formed by the prompt \\{NOx\\} mechanisms. The elimination of thermal \\{NOx\\} makes the \\{NOx\\} emissions independent of residence time or reference velocity and independent of pressure. Also there is no influence of air inlet temperature for the same flame temperature. Where legislation requires emissions to be as low as can be achieved, emissions below 4 ppm in production engines are current technology and this review shows the potential to get even lower than this in the future.

G.E. Andrews

2013-01-01T23:59:59.000Z

57

Reducing nitrogen oxides emissions from the combustion of LCV gas staged firing  

E-Print Network [OSTI]

with cotton gin tr ash, one of the primary fuels under consider ation, r esulted in flue NO levels ranging from 650-B60 ng/J (1. 5-2. 0 lb/MBtu). The Texas Air Control Board (TACB) will issue a facility a permit to operate only if NOx emissions are within... NO Methods of NOx Control Methods of NOx control may be lumped into two cate- gories: flue gas treatment (FGT) and combustion modifica- tion. The different processes are described below. Flue Gas Tr eatment Most of the research on FGT to date has been...

Finch, Stanley Frank

2012-06-07T23:59:59.000Z

58

Communicating potential risks of uncontrolled site development at a Fusrap site  

SciTech Connect (OSTI)

This paper describes a particular risk communication challenge at the FUSRAP Maywood Superfund Site (the Site) in Maywood, New Jersey, USA. That challenge is communicating the potential human exposure risks of uncontrolled site development to landowners, tenants, private contractors and public works entities that may engage in construction activities at or adjacent to Site properties. This is of special concern because the Site does not have the authority to establish physical control over most of the properties where contamination is known or suspected to exist. Consequently, a range of communications techniques have been employed to alert property owners and others to the risks of uncontrolled site development. Each technique has its particular limitations, but collectively this multi-channel communication strategy has proved successful in delivering the risk message. (authors)

Roos, A.D. [U.S. Army Corps of Engineers, New York District, New York, NY (United States); Kollar, W. [Shaw Environmental, Inc., Maywood, NJ (United States)

2008-07-01T23:59:59.000Z

59

Reducing or stopping the uncontrolled flow of fluid such as oil from a well  

DOE Patents [OSTI]

The uncontrolled flow of fluid from an oil or gas well may be reduced or stopped by injecting a composition including 2-cyanoacrylate ester monomer into the fluid stream. Injection of the monomer results in a rapid, perhaps instantaneous, polymerization of the monomer within the flow stream of the fluid. This polymerization results in formation of a solid plug that reduces or stops the flow of additional fluid from the well.

Hermes, Robert E

2014-02-18T23:59:59.000Z

60

Influence of Oxidized Biodiesel Blends on Regulated and Unregulated Emissions from a Diesel Passenger Car  

Science Journals Connector (OSTI)

Few studies are available on modern passenger cars, employed common-rail engine systems, and after-treatment technologies, and even fewer studies report results, which are not necessarily representative of actual driving conditions, making it difficult to assess the fuel impact on diesel car fleet emissions. ... Although gasoline engines are expected to be replaced by hydrogen-powered fuel cells, compression-ignition engines, the diesel engines, are expected to remain in use for high-power applications because of limitations of hydrogen-storage densities. ... transesterification and sequential esterification-transesterification, followed by washing in water in both cases, in order to set out the most suitable operational conditions to achieve the highest FAME percentage in the shortest time. ...

Georgios Karavalakis; Evangelos Bakeas; Stamos Stournas

2010-05-24T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations  

Science Journals Connector (OSTI)

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recyc...

Brian K. Gullett; William P. Linak…

2007-03-01T23:59:59.000Z

62

Nitrogen Oxides, Sulphur Trioxide and Mercury Emissions during Oxy-Fuel Fluidized Bed Combustion of Victorian Brown Coal  

Science Journals Connector (OSTI)

This study investigates, for the first time, the NOX, N2O, SO3 and Hg emissions from combustion of a Victorian brown coal in a 10 kWth fluidized bed unit under oxy-fuel combustion conditions. Compared to air combustion, lower NOX emissions and higher N2O ...

Bithi Roy; Luguang Chen; Sankar Bhattacharya

2014-11-17T23:59:59.000Z

63

Effect of the NMDA receptor antagonist MK-801 on recovery from spinal cord injury in rats given uncontrollable stimulation  

E-Print Network [OSTI]

, were given the NMDA receptor antagonist MK-801 (0.08 mg/kg, i.p.) or its vehicle before receiving either a bout of uncontrollable stimulation or identical treatment without the stimulation itself. Their hindlimb motor activity was monitored for 21 days...

Petrich, Christine

2006-08-16T23:59:59.000Z

64

Journal of Asian Electric Vehicles, Volume 9, Number 1, June 2011 Uncontrolled Generation of Traciton Motors in Hybrid Electric Vehicles  

E-Print Network [OSTI]

of Traciton Motors in Hybrid Electric Vehicles Xiaofeng Ding 1 , Jinglin Liu 2 , and Chris Mi 3 1 Department Generation of Traciton Motors in Hybrid Electric Vehicles 1460 2. SIMPLE ANALYTICAL MODEL OF UCG 2.1 ModelJournal of Asian Electric Vehicles, Volume 9, Number 1, June 2011 1459 Uncontrolled Generation

Mi, Chunting "Chris"

65

Estimation of nitrous oxide emissions (GHG) from wastewater treatment plants using closed-loop mass balance and data reconciliation  

Science Journals Connector (OSTI)

The amount of greenhouse gases (GHG), especially, nitrous oxide (N2O) emitted from wastewater treatment plants (WWTP) using data reconciliation and closed-loop mass balance was estimated. This study is based on a...

JungJin Lim; Boddupalli Sankarrao; TaeSeok Oh…

2012-09-01T23:59:59.000Z

66

Effect of encapsulated calcium carbide on dinitrogen, nitrous oxide, methane, and carbon dioxide emissions from flooded rice  

Science Journals Connector (OSTI)

The efficiency of N use in flooded rice is usually low, chiefly due to gaseous losses. Emission of CH4, a gas implicated in global warming, can also be substantial in flooded rice. In a greenhouse study, the nitr...

K. F. Bronson; A. R. Mosier

1991-05-01T23:59:59.000Z

67

Vehicle Emissions Review - 2011 | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

NOx control, diesel oxidation catalysts, gasoline particulate filters deer11johnson.pdf More Documents & Publications Vehicle Emissions Review - 2012 Diesel Emission...

68

Analysis of Strategies for Reducing Multiple Emissions from Electric Power Plants: Sulfur Dioxide, Nitrogen Oxides, Carbon Dioxide, and Mercury and a Renewable Portfolio Standard  

Gasoline and Diesel Fuel Update (EIA)

3 3 ERRATA Analysis of Strategies for Reducing Multiple Emissions from Electric Power Plants: Sulfur Dioxide, Nitrogen Oxides, Carbon Dioxide, and Mercury and a Renewable Portfolio Standard July 2001 Energy Information Administration Office of Integrated Analysis and Forecasting U.S. Department of Energy Washington, DC 20585 This Service Report was prepared by the Energy Information Administration, the independent statistical and analytical agency within the Department of Energy. The information contained herein should be attributed to the Contacts This report was prepared by the Office of Integrated Analysis and Forecasting, Energy Information Adminis- tration. General questions concerning the report may be directed to Mary J. Hutzler (202/586-2222, mhutzler @eia.doe.gov), Director of the Office of Integrated Analysis and Forecasting, Scott B. Sitzer (202/586-2308,

69

The Advanced Tangentially Fired Combustion Techniques for the Reduction of Nitrogen Oxides (NOx) Emissions From Coal-Fired Boilers Demonstration Project: A DOE Assessment  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

2 2 The Advanced Tangentially Fired Combustion Techniques for the Reduction of Nitrogen Oxides (NO ) Emissions From Coal-Fired Boilers X Demonstration Project: A DOE Assessment March 2000 U.S. Department of Energy National Energy Technology Laboratory P.O. Box 880, 3610 Collins Ferry Road Morgantown, WV 26507-0880 and P.O. Box 10940, 626 Cochrans Mill Road Pittsburgh, PA 15236-0940 2 Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or

70

Clean coal technology: selective catalytic reduction (SCR) technology for the control of nitrogen oxide emissions from coal-fired boilers  

SciTech Connect (OSTI)

The report discusses a project carried out under the US Clean Coal Technology (CCT) Demonstration Program which demonstrated selective catalytic reduction (SCR) technology for the control of NOx emissions from high-sulphur coal-fired boilers under typical boilers conditions in the United States. The project was conducted by Southern Company Services, Inc., who served as a co-funder and as the host at Gulf Power Company's Plant Crist. The SCR process consists of injecting ammonia (NH{sub 3}) into boiler flue gas and passing the flue gas through a catalyst bed where the Nox and NH{sub 3} react to form nitrogen and water vapor. The results of the CCTDP project confirmed the applicability of SCR for US coal-fired power plants. In part as a result of the success of this project, a significant number of commercial SCR units have been installed and are operating successfully in the United States. By 2007, the total installed SCR capacity on US coal-fired units will number about 200, representing about 100,000 MWe of electric generating capacity. This report summarizes the status of SCR technology. 21 refs., 3 figs., 2 tabs., 10 photos.

NONE

2005-05-01T23:59:59.000Z

71

Fuel saving, carbon dioxide emission avoidance, and syngas production by tri-reforming of flue gases from coal- and gas-fired power stations, and by the carbothermic reduction of iron oxide  

Science Journals Connector (OSTI)

Flue gases from coal, gas, or oil-fired power stations, as well as from several heavy industries, such as the production of iron, lime and cement, are major anthropogenic sources of global CO2 emissions. The newly proposed process for syngas production based on the tri-reforming of such flue gases with natural gas could be an important route for CO2 emission avoidance. In addition, by combining the carbothermic reduction of iron oxide with the partial oxidation of the carbon source, an overall thermoneutral process can be designed for the co-production of iron and syngas rich in CO. Water-gas shift (WGS) of CO to H2 enables the production of useful syngas. The reaction process heat, or the conditions for thermoneutrality, are derived by thermochemical equilibrium calculations. The thermodynamic constraints are determined for the production of syngas suitable for methanol, hydrogen, or ammonia synthesis. The environmental and economic consequences are assessed for large-scale commercial production of these chemical commodities. Preliminary evaluations with natural gas, coke, or coal as carbon source indicate that such combined processes should be economically competitive, as well as promising significant fuel saving and CO2 emission avoidance. The production of ammonia in the above processes seems particularly attractive, as it consumes the nitrogen in the flue gases.

M. Halmann; A. Steinfeld

2006-01-01T23:59:59.000Z

72

Oxidized organic functional groups in aerosol particles from forest emissions measured at mid-mountain and high- elevation mountain sites in Whistler, BC  

E-Print Network [OSTI]

with fossil fuel combustion and marine emissions (Russell etfuel combustion, and biomass burning (BB). Natural sources include biogenic (from the biosphere), marine (

Schwartz, Rachel E.

2010-01-01T23:59:59.000Z

73

Rational Catalyst Design Applied to Development of Advanced Oxidation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Catalyst Design Applied to Development of Advanced Oxidation Catalysts for Diesel Emission Control Rational Catalyst Design Applied to Development of Advanced Oxidation...

74

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, third quarter 1991  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company`s Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO{sub x} combustion technologies on NO{sub x} emissions and boiler performance. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project.

Not Available

1992-02-03T23:59:59.000Z

75

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO sub x ) emissions from coal-fired boilers  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company's Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO{sub x} combustion technologies on NO{sub x} emissions and boiler performance. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project.

Not Available

1992-02-03T23:59:59.000Z

76

Excitation mechanism and thermal emission quenching of Tb ions in silicon rich silicon oxide thin films grown by plasma-enhanced chemical vapour deposition—Do we need silicon nanoclusters?  

SciTech Connect (OSTI)

In this work, we will discuss the excitation and emission properties of Tb ions in a Silicon Rich Silicon Oxide (SRSO) matrix obtained at different technological conditions. By means of electron cyclotron resonance plasma-enhanced chemical vapour deposition, undoped and doped SRSO films have been obtained with different Si content (33, 35, 39, 50 at. %) and were annealed at different temperatures (600, 900, 1100?°C). The samples were characterized optically and structurally using photoluminescence (PL), PL excitation, time resolved PL, absorption, cathodoluminescence, temperature dependent PL, Rutherford backscattering spectrometry, Fourier transform infrared spectroscopy and positron annihilation lifetime spectroscopy. Based on the obtained results, we discuss how the matrix modifications influence excitation and emission properties of Tb ions.

Podhorodecki, A., E-mail: artur.p.podhorodecki@pwr.wroc.pl; Golacki, L. W.; Zatryb, G.; Misiewicz, J. [Institute of Physics, Wroclaw University of Technology, Wybrzeze Wyspianskiego 27, 50-370 Wroclaw (Poland); Wang, J.; Jadwisienczak, W. [School of EECS, Ohio University, Stocker Center 363, Athens, Ohio 45701 (United States); Fedus, K. [Institute of Physics, Nicholas Copernicus University, Grudziadzka 5/7, 87-100 Torun (Poland); Wojcik, J.; Wilson, P. R. J.; Mascher, P. [Department of Engineering Physics and Centre for Emerging Device Technologies, McMaster University, 1280 Main St. W, Hamilton, Ontario L8S4L7 (Canada)

2014-04-14T23:59:59.000Z

77

Air emissions inventory for the Idaho National Engineering Laboratory -- 1995 emissions report  

SciTech Connect (OSTI)

This report presents the 1995 update of the Air Emission Inventory for the Idaho National Engineering Laboratory (INEL). The INEL Air Emission Inventory documents sources and emissions of non-radionuclide pollutants from operations at the INEL. The report describes the emission inventory process and all of the sources at the INEL, and provides non-radionuclide emissions estimates for stationary sources. The air contaminants reported include nitrogen oxides, sulfur oxides, carbon monoxide, volatile organic compounds, particulates, and hazardous air pollutants (HAPs).

NONE

1996-06-01T23:59:59.000Z

78

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Fourth quarterly technical progress report, [October--December, 1992  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a U. S. Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NOx) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company`s Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NOx combustion technologies on NOx emissions and boiler performance. A target of achieving fifty percent NOx reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NOx control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NOx concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NOx reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. During this quarter, tests of the LNCFS Level III system were conducted to determine the effect that fuel fineness has on NOx emissions and unburned carbon levels. Results showed that changing the fineness of the fuel has almost no effect on NOx emissions; however, unburned carbon levels can be reduced significantly by increasing fuel fineness.

Not Available

1992-12-31T23:59:59.000Z

79

Stabilized chromium oxide film  

DOE Patents [OSTI]

Stabilized air-oxidized chromium films deposited on high-power klystron ceramic windows and sleeves having a thickness between 20 and 150.ANG. are useful in lowering secondary electron emission yield and in avoiding multipactoring and window failure due to overheating. The ceramic substrate for the film is chosen from alumina, sapphire or beryllium oxide.

Garwin, Edward L. (Los Altos, CA); Nyaiesh, Ali R. (Palo Alto, CA)

1988-01-01T23:59:59.000Z

80

Stabilized chromium oxide film  

DOE Patents [OSTI]

Stabilized air-oxidized chromium films deposited on high-power klystron ceramic windows and sleeves having a thickness between 20 and 150A are useful in lowering secondary electron emission yield and in avoiding multipactoring and window failure due to overheating. The ceramic substrate for the film is chosen from alumina, sapphire or beryllium oxide.

Nyaiesh, A.R.; Garwin, E.L.

1986-08-04T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Reducing the contribution of the power sector to ground-level ozone pollution : an assessment of time-differentiated pricing of nitrogen oxide emissions  

E-Print Network [OSTI]

Nitrogen oxide (NOx) is a prevalent air pollutant across the United States and a requisite precursor for tropospheric (ground-level) ozone formation. Both pollutants significantly impact human health and welfare, so National ...

Craig, Michael T. (Michael Timothy)

2014-01-01T23:59:59.000Z

82

The effects of cycle-to-cycle variations on nitric oxide (NO) emissions for a spark-ignition engine: Numerical results  

E-Print Network [OSTI]

. To carry out the proposed study, an engine simulation model was used. The simulation determines engine performance and NO emissions as functions of engine operating conditions, engine design parameters, and combustion parameters. An automotive, spark-ignition...

Villarroel, Milivoy

2004-11-15T23:59:59.000Z

83

Fact #825: June 16, 2014 Tier 3 Non-Methane Organic Gases Plus Nitrogen Oxide Emission Standards, Model Years 2017-2025  

Broader source: Energy.gov [DOE]

The Environmental Protection Agency finalized Tier 3 emission standards in a rule issued in March 2014. One effect of the rule is a decrease in the combined amount of non-methane organic gases ...

84

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO[sub x]) emissions from coal-fired boilers  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO[sub x]) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company's Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO[sub x] combustion technologies on NO[sub x] emissions and boiler performance. A target of achieving fifty percent NO[sub x] reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NO[sub x] control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NO[sub x] concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NO[sub x] reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. This technical progress report presents the LNCFS Level I short-term data collected during this quarter. In addition, a comparison of all the long-term emissions data that have been collected to date is included.

Not Available

1992-11-25T23:59:59.000Z

85

500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO[sub x]) emissions from coal-fired boilers  

SciTech Connect (OSTI)

The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO[sub x] burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO[sub x] reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulatecharacteristics and boiler efficiency. Baseline, AOFA, and LNB without AOFA test segments have been completed. Analysis of the 94 days of LNB long-term data collected show the full-load NO[sub x] emission levels to be approximately 0.65 lb/MBtu. Flyash LOI values for the LNB configuration are approximately 8 percent at full-load. Corresponding values for the AOFA configuration are 0.94 lb/MBtu and approximately 10 percent. Abbreviated diagnostic tests for the LNB+AOFA configuration indicate that at 500 MWe, NO[sub x] emissions are approximately 0.55 lb/MBtu with corresponding flyash LOI values of approximately 11 percent. For comparison, the long-term full-load, baseline NO[sub x] emission level was approximately 1.24 lb/MBtu at 5.2 percent LOI. Comprehensive testing of the LNB+AOFA configuration will be performed when the stackparticulate emissions issue is resolved. Testing of a process optimization package on Plant Hammond Unit 4 was performed during this quarter. The software was configured to minimize NO[sub x] emissions using total combustion air flow and advanced overfire air distribution as the controlled parameters. Preliminary results from this testing indicate that this package shows promise in reducing NO[sub x] emissions while maintaining or improving other boiler performance parameters.

Not Available

1992-01-01T23:59:59.000Z

86

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, first quarter 1992  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company`s Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO{sub x} combustion technologies on NO{sub x} emissions and boiler performance. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NO{sub x} control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NO{sub x} concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. This technical progess report presents the LNCFS Level III long-term data collected during this quarter. NO{sub x} emissions for each day of long-term testing are presented. The average NO{sub x} emission during long-term testing was 0.39 lb/MBtu at an average load of 155 MW. The effect of the low NO{sub x} combustion system on other combustion parameters such as carbon monoxide, excess oxygen level, and carbon carryover are also included.

Not Available

1992-05-20T23:59:59.000Z

87

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO[sub x]) emissions from coal-fired boilers  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO[sub x]) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company's Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO[sub x] combustion technologies on NO[sub x] emissions and boiler performance. A target of achieving fifty percent NO[sub x] reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NO[sub x] control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NO[sub x] concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NO[sub x] reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. This technical progess report presents the LNCFS Level III long-term data collected during this quarter. NO[sub x] emissions for each day of long-term testing are presented. The average NO[sub x] emission during long-term testing was 0.39 lb/MBtu at an average load of 155 MW. The effect of the low NO[sub x] combustion system on other combustion parameters such as carbon monoxide, excess oxygen level, and carbon carryover are also included.

Not Available

1992-05-20T23:59:59.000Z

88

Electron Emission from Slightly Oxidized Depleted Uranium Generated by its Own Radioactivity Measured by Electron Spectroscopy, and Electron-Induced Dissociation and Ionization of Hydrogen Near its Surface.  

SciTech Connect (OSTI)

Energy dependent electron emission (counts per second) between zero and 1.4 keV generated by the natural reactivity of uranium was measured by an electrostatic spectrometer with known acceptance angle and acceptance area. The electron intensity decreases continuously with energy, but at different rates in different energy regimes, suggesting that a variety of processes may be involved in producing the observed electron emission. The spectrum was converted to energy dependent electron flux (e-/cm{sup 2} s) using the assumption that the emission has a cosine angular distribution. The flux decreased rapidly from {approx}10{sup 6}/cm{sup 2}s to {approx}10{sup 5}/cm{sup 2}s in the energy range from zero to 200 eV, and then more slowly from {approx}10{sup 5}/cm{sup 2}s to {approx}3*10{sup 4}/cm{sup 2} s in the range from 200 to 1400 eV. The energy dependent electron mean free path in gases together with literature cross sections for electron induced reactions were used to determine the number of ionization and dissociation reactions per cm{sup 2}s within the inelastic mean free path of electrons, and found to be about 1.3*10{sup 8}/cm{sup 2}s and 1.5*10{sup 7}/cm{sup 2}s, respectively, for hydrogen. An estimate of the number of ionization and dissociation reactions occurring within the total range, rather than the mean free path of electrons in gases resulted in 6.2*10{sup 9}/cm{sup 2}s and 1.3*10{sup 9}/cm{sup 2}s, respectively. The total energy flux carried by electrons from the surface is suspiciously close to the total possible energy generated by one gram of uranium. A likely source of error is the assumption that the electron emission has a cosine distribution. Angular distribution measurements of the electron emission would check that assumption, and actual measurement of the total current emanating from the surface are needed to confirm the value of the current calculated in section II. These results must therefore be used with caution - until they are confirmed by other measurements.

Siekhaus, W J; Nelson, A J

2011-10-26T23:59:59.000Z

89

Field emission study of cobalt ion implanted porous silicon  

E-Print Network [OSTI]

Analysis . Field Emission Measurements of Cobalt Implanted Porous Silicon Differences between the 1mplanted Porous Silicon Field Emission Devioe and the Al-anode Oxidized Porous Silicon Field Emission Diode VII CONCLUSION 70 94 99 REFERENCES... Emission Diode (OPSFED) was developed and studied [8] . The OPSFED was using the irregularity on the interface between the oxidized porous silicon film and silicon substrate as field emission cathodes, and a thin aluminum layer deposited...

Liu, Hongbiao

2012-06-07T23:59:59.000Z

90

Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, fourth quarter 1991  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of an Innovative Clean Coal Technology (ICCT) demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. The project is being conducted at Georgia Power Company`s Plant Hammond Unit 4 located near Rome, Georgia. The primary goal of this project is the characterization of the low NO{sub x} combustion equipment through the collection and analysis of long-term emissions data. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO{sub x} burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as parameters such as particulate characteristics and boiler efficiency.

Not Available

1992-04-21T23:59:59.000Z

91

Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, Second quarter 1992  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of an Innovative Clean Coal Technology (ICCT) demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (No{sub x}) emissions from coal-fired boilers. The project is being conducted at Georgia Power Company`s Plant Hammond Unit 4 located near Rome, Georgia. The primary goal of this project is the characterization of the low NO{sub x} combustion equipment through the collection and analysis of long-term emissions data. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO{sub x} burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency.

Not Available

1992-08-24T23:59:59.000Z

92

Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, First quarter 1992  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of an Innovative Clean Coal Technology (ICCT) demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. The project is being conducted at Georgia Power Company`s Plant Hammond Unit 4 located near Rome, Georgia. The primary goal of this project is the characterization of the low NO{sub x} combustion equipment through the collection and analysis of long-term emissions data. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO{sub x} burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency.

Not Available

1992-12-31T23:59:59.000Z

93

Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO[sub x]) emissions from coal-fired boilers  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of an Innovative Clean Coal Technology (ICCT) demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (No[sub x]) emissions from coal-fired boilers. The project is being conducted at Georgia Power Company's Plant Hammond Unit 4 located near Rome, Georgia. The primary goal of this project is the characterization of the low NO[sub x] combustion equipment through the collection and analysis of long-term emissions data. A target of achieving fifty percent NO[sub x] reduction using combustion modifications has been established for the project. The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO[sub x] burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO[sub x] reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency.

Not Available

1992-08-24T23:59:59.000Z

94

Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO sub x ) emissions from coal-fired boilers  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of an Innovative Clean Coal Technology (ICCT) demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. The project is being conducted at Georgia Power Company's Plant Hammond Unit 4 located near Rome, Georgia. The primary goal of this project is the characterization of the low NO{sub x} combustion equipment through the collection and analysis of long-term emissions data. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO{sub x} burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as parameters such as particulate characteristics and boiler efficiency.

Not Available

1992-04-21T23:59:59.000Z

95

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, fourth quarter 1991  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company`s Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO{sub x} combustion technologies on NO{sub x} emissions and boiler performance. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NO{sub x} control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NO{sub x} concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency.

Not Available

1992-05-18T23:59:59.000Z

96

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO sub x ) emissions from coal-fired boilers  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company's Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO{sub x} combustion technologies on NO{sub x} emissions and boiler performance. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NO{sub x} control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NO{sub x} concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency.

Not Available

1992-05-18T23:59:59.000Z

97

Emissions Trading  

Science Journals Connector (OSTI)

Emissions trading is a comparatively new policy instrument which ... electricity systems in Europe. The development of emissions trading thus represents an innovation in its own...

2009-01-01T23:59:59.000Z

98

Demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NOx) emissions from high-sulfur coal-fired boilers  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NO{sub x}) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NO{sub x} to convert it to nitrogen and water vapor.

Not Available

1991-11-01T23:59:59.000Z

99

Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, second quarter 1992  

SciTech Connect (OSTI)

This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company`s Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO{sub x} combustion technologies on NO{sub x} emissions and boiler performance. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NO{sub x} control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NO{sub x} concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. This technical progress report presents the LNCFS Level I short-term data collected during this quarter. In addition, a comparison of all the long-term emissions data that have been collected to date is included.

Not Available

1992-11-25T23:59:59.000Z

100

Reduction of NOx emission on NiCrAl-Titanium Oxide coated direct injection diesel engine fuelled with radish (Raphanus sativus) biodiesel  

Science Journals Connector (OSTI)

The main aim of this study is the experimental investigation of single cylinder DI diesel engine with and without coating. Diesel and radish (Raphanus sativus) oil Methyl Ester are used as fuels and the results are compared to find the effect of biodiesel in a thermal barrier coating engine. For this purpose engine cylinder head valves and piston crown are coated with 100??m of nickel-chrome-aluminium bond coat and 450??m of TiO2 by the plasma spray method. Radish oil methyl ester is produced by the transesterification process method. From the experimental investigation slight increase in specific fuel consumption in thermal barrier coating engine is observed when compared with the uncoated engine whereas NOx HC Smoke and CO emissions decreased with coated engine for all test fuels used in the coated engine when compared with that of the uncoated engine.

V. Ravikumar; D. Senthilkumar

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Aerosol Jet Printing of LSCF-CGO Cathode for Solid Oxide Fuel Cells.  

E-Print Network [OSTI]

??Solid oxide fuel cell (SOFC) technology has attracted great attention due to advantages such as low emissions and high efficiency. In this work, solid oxide… (more)

Gardner, Paul

2011-01-01T23:59:59.000Z

102

Mercury emissions from municipal solid waste combustors  

SciTech Connect (OSTI)

This report examines emissions of mercury (Hg) from municipal solid waste (MSW) combustion in the United States (US). It is projected that total annual nationwide MSW combustor emissions of mercury could decrease from about 97 tonnes (1989 baseline uncontrolled emissions) to less than about 4 tonnes in the year 2000. This represents approximately a 95 percent reduction in the amount of mercury emitted from combusted MSW compared to the 1989 mercury emissions baseline. The likelihood that routinely achievable mercury emissions removal efficiencies of about 80 percent or more can be assured; it is estimated that MSW combustors in the US could prove to be a comparatively minor source of mercury emissions after about 1995. This forecast assumes that diligent measures to control mercury emissions, such as via use of supplemental control technologies (e.g., carbon adsorption), are generally employed at that time. However, no present consensus was found that such emissions control measures can be implemented industry-wide in the US within this time frame. Although the availability of technology is apparently not a limiting factor, practical implementation of necessary control technology may be limited by administrative constraints and other considerations (e.g., planning, budgeting, regulatory compliance requirements, etc.). These projections assume that: (a) about 80 percent mercury emissions reduction control efficiency is achieved with air pollution control equipment likely to be employed by that time; (b) most cylinder-shaped mercury-zinc (CSMZ) batteries used in hospital applications can be prevented from being disposed into the MSW stream or are replaced with alternative batteries that do not contain mercury; and (c) either the amount of mercury used in fluorescent lamps is decreased to an industry-wide average of about 27 milligrams of mercury per lamp or extensive diversion from the MSW stream of fluorescent lamps that contain mercury is accomplished.

Not Available

1993-05-01T23:59:59.000Z

103

Demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NO[sub x]) emissions from high-sulfur coal-fired boilers  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NO[sub x]) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NO[sub x] to convert it to nitrogen and water vapor. Although SCR is widely practiced in Japan and Europe, there are numerous technical uncertainties associated with applying SCR to US coals. These uncertainties include: (1) potential catalyst deactivation due to poisoning by trace metal species present in US coals that are not present in other fuels. (2) performance of the technology and effects on the balance-of-plant equipment in the presence of high amounts of SO[sub 2] and SO[sub 3]. (3) performance of a wide variety of SCR catalyst compositions, geometries and methods of manufacture under typical high-sulfur coal-fired utility operating conditions. These uncertainties will be explored by constructing a series of small-scale SCR reactors and simultaneously exposing different SCR catalysts to flue gas derived from the combustion of high sulfur U. S. coal.

Not Available

1992-08-01T23:59:59.000Z

104

EIA - AEO2010 - Emissions projections  

Gasoline and Diesel Fuel Update (EIA)

Emissions Projections Emissions Projections Annual Energy Outlook 2010 with Projections to 2035 Emissions Projections Figure 93. Carbon dioxide emissions by sector and fuel, 2008 and 2035 Click to enlarge » Figure source and data excel logo Figure 94. Sulfur dioxide emissions from electricity generation, 2000-2035 Click to enlarge » Figure source and data excel logo Figure 95. Nitrogen oxide emissions from electricity generation, 2000-2035 Click to enlarge » Figure source and data excel logo Growth of carbon dioxide emissions slows in the projections Federal and State energy policies recently enacted will stimulate increased use of renewable technologies and efficiency improvements in the future, slowing the growth of energy-related CO2 emissions through 2035. In the Reference case, emissions do not exceed pre-recession 2007 levels until 2025. In 2035, energy-related CO2 emissions total 6,320 million metric tons, about 6 percent higher than in 2007 and 9 percent higher than in 2008 (Figure 93). On average, emissions in the Reference case grow by 0.3 percent per year from 2008 to 2035, compared with 0.7 percent per year from 1980 to 2008.

105

Just the Basics: Vehicle Emissions  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Are Exhaust Are Exhaust Emissions? In most heavily settled areas of the U.S., the personal automobile is the single greatest producer of harmful vehicle exhaust emissions. Exhaust emissions are generated by the fuel-air mixture burning in internal combus- tion engines, both gasoline-powered and diesel-powered. Emissions are also produced by fuel evaporation within the vehicle when it is stopped, and again during fueling. The constituents of car (gasoline and diesel) and truck (diesel) emissions vary depending on fuel type and indi- vidual vehicle operating characteris- tics. The bulk of vehicular emissions are composed of water vapor, carbon dioxide, nitrogen, and oxygen (in unconsumed air). There are other pollutants, such as carbon monoxide, nitrogen oxides, unburned fuel, and

106

Emissions Trading  

Science Journals Connector (OSTI)

Emissions trading is a market-based instrument to achieve ... The current international dissemination and intended linking of emissions trading schemes underlines the growing relevance of this ... . There are thr...

Edwin Woerdman

2014-06-01T23:59:59.000Z

107

Emissions Trading  

Science Journals Connector (OSTI)

This chapter covers a series of operations which are essential for the implementation of an efficient emissions trading market on the domestic and international level. An introduction to how a national emissions trading

Dr. Michael See

2001-01-01T23:59:59.000Z

108

electricity emission factors | OpenEI  

Open Energy Info (EERE)

emission factors emission factors Dataset Summary Description Emissions from energy use in buildings are usually estimated on an annual basis using annual average multipliers. Using annual numbers provides a reasonable estimation of emissions, but it provides no indication of the temporal nature of the emissions. Therefore, there is no way of understanding the impact on emissions from load shifting and peak shaving technologies such as thermal energy storage, on-site renewable energy, and demand control. Source NREL Date Released April 11th, 2011 (3 years ago) Date Updated April 11th, 2011 (3 years ago) Keywords buildings carbon dioxide emissions carbon footprinting CO2 commercial buildings electricity emission factors ERCOT hourly emission factors interconnect nitrogen oxides

109

sulfur dioxide emissions | OpenEI  

Open Energy Info (EERE)

sulfur dioxide emissions sulfur dioxide emissions Dataset Summary Description Emissions from energy use in buildings are usually estimated on an annual basis using annual average multipliers. Using annual numbers provides a reasonable estimation of emissions, but it provides no indication of the temporal nature of the emissions. Therefore, there is no way of understanding the impact on emissions from load shifting and peak shaving technologies such as thermal energy storage, on-site renewable energy, and demand control. Source NREL Date Released April 11th, 2011 (3 years ago) Date Updated April 11th, 2011 (3 years ago) Keywords buildings carbon dioxide emissions carbon footprinting CO2 commercial buildings electricity emission factors ERCOT hourly emission factors interconnect nitrogen oxides

110

Emissions Of Greenhouse Gases From Rice Agriculture  

SciTech Connect (OSTI)

This project produced detailed data on the processes that affect methane and nitrous oxide emissions from rice agriculture and their inter-relationships. It defines the shifting roles and potential future of these gases in causing global warming and the benefits and tradeoffs of reducing emissions. The major results include: 1). Mechanisms and Processes Leading to Methane Emissions are Delineated. Our experiments have tested the standard model of methane emissions from rice fields and found new results on the processes that control the flux. A mathematical mass balance model was used to unravel the production, oxidation and transport of methane from rice. The results suggested that when large amounts of organic matter are applied, the additional flux that is observed is due to both greater production and reduced oxidation of methane. 2). Methane Emissions From China Have Been Decreasing Over the Last Two Decades. We have calculated that methane emissions from rice fields have been falling in recent decades. This decrease is particularly large in China. While some of this is due to reduced area of rice agriculture, the bigger effect is from the reduction in the emission factor which is the annual amount of methane emitted per hectare of rice. The two most important changes that cause this decreasing emission from China are the reduced use of organic amendments which have been replaced by commercial nitrogen fertilizers, and the increased practice of intermittent flooding as greater demands are placed on water resources. 3). Global Methane Emissions Have Been Constant For More Than 20 Years. While the concentrations of methane in the atmosphere have been leveling off in recent years, our studies show that this is caused by a near constant total global source of methane for the last 20 years or more. This is probably because as some anthropogenic sources have increased, others, such as the rice agriculture source, have fallen. Changes in natural emissions appear small. 4). Nitrous Oxide Emissions From Rice Fields Increase as Methane Emissions Drop. Inundated conditions favor anaerobic methane production with high emission rates and de-nitrification resulting in modest nitrous oxide emissions. Under drier conditions such as intermittent flooding, methane emissions fall and nitrous oxide emissions increase. Increased nitrogen fertilizer use increases nitrous oxide emissions and is usually accompanied by reduced organic matter applications which decreases methane emissions. These mechanisms cause a generally inverse relationship between methane and nitrous oxide emissions. Reduction of methane from rice agriculture to control global warming comes with tradeoffs with increased nitrous oxide emissions. 5). High Spatial Resolution Maps of Emissions Produced. Maps of methane and nitrous oxide emissions at a resolution of 5 min × 5 min have been produced based on the composite results of this research. These maps are necessary for both scientific and policy uses.

M. Aslam K. Khalil

2009-07-16T23:59:59.000Z

111

Effectiveness of a Diesel Oxidation Catalyst (DOC) to control...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Effectiveness of a Diesel Oxidation Catalyst (DOC) to control CO and hydrocarbon emissions from Reactivity Controlled Compression Ignition (RCCI) combustion Effectiveness of a...

112

Development of non-premixed porous inserted regenerative thermal oxidizer  

Science Journals Connector (OSTI)

In this study, a porous inserted regenerative thermal oxidizer (PRTO) system was developed for a... x emissions and high radiant efficiency. Zirconium dioxide (ZrO2...) ceramic ...

Jun-chun Zhang; Le-ming Cheng; Cheng-hang Zheng…

2013-09-01T23:59:59.000Z

113

Diesel Particulate Oxidation Model: Combined Effects of Fixed...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Volatile Carbon Diesel Particulate Oxidation Model: Combined Effects of Fixed & Volatile Carbon Poster presented at the 16th Directions in Engine-Efficiency and Emissions Research...

114

Zero emission coal  

SciTech Connect (OSTI)

We discuss a novel, emission-free process for producing hydrogen or electricity from coal. Even though we focus on coal, the basic design is compatible with any carbonaceous fuel. The process uses cyclical carbonation of calcium oxide to promote the production of hydrogen from carbon and water. The carbonation of the calcium oxide removes carbon dioxide from the reaction products and provides the additional energy necessary to complete hydrogen production without additional combustion of carbon. The calcination of the resulting calcium carbonate is accomplished using the high temperature waste heat from solid oxide fuel cells (SOFC), which generate electricity from hydrogen fuel. Converting waste heat back to useful chemical energy allows the process to achieve very high conversion efficiency from fuel energy to electrical energy. As the process is essentially closed-loop, the process is able to achieve zero emissions if the concentrated exhaust stream of CO{sub 2} is sequestered. Carbon dioxide disposal is accomplished by the production of magnesium carbonate from ultramafic rock. The end products of the sequestration process are stable naturally occurring minerals. Sufficient rich ultramafic deposits exist to easily handle all the world's coal.

Ziock, H.; Lackner, K.

2000-08-01T23:59:59.000Z

115

NETL: IEP - Mercury Emissions Control: Emissions Characterization  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Control Control Emissions Characterization In anticipation of the 1990 CAAAs, specifically the draft Title III regarding the characterization of potential HAPs from electric steam generating units, DOE initiated a new Air Toxics Program in 1989. The DOE Mercury Measurement and Control Program evolved as a result of the findings from the comprehensive assessment of hazardous air pollutants studies conducted by DOE from 1990 through 1997. DOE, in collaboration with EPRI, performed stack tests at a number of coal-fired power plants (identified on map below) to accurately determine the emission rates of a series of potentially toxic chemicals. These tests had not been conducted previously because of their cost, about $1 million per test, so conventional wisdom on emissions was based on emission factors derived from analyses of coal. In general, actual emissions were found to be about one-tenth previous estimates, due to a high fraction of the pollutants being captured by existing particulate control systems. These data resulted in a decision by EPA that most of these pollutants were not a threat to the environment, and needed no further regulation at power plants. This shielded the coal-fired power industry from major (tens of millions) costs that would have resulted from further controlling these emissions. However, another finding of these studies was that mercury was not effectively controlled in coal-fired utility boiler systems. Moreover, EPA concluded that a plausible link exists between these emissions and adverse health effects. Ineffective control of mercury by existing control technologies resulted from a number of factors, including variation in coal composition and variability in the form of the mercury in flue gases. The volatility of mercury was the main contributor for less removal, as compared to the less volatile trace elements/metals which were being removed at efficiencies over 99% with the fly ash. In addition, it was determined that there was no reliable mercury speciation method to accurately distinguish between the elemental and oxidized forms of mercury in the flue gas. These two forms of mercury respond differently to removal techniques in existing air pollution control devices utilized by the coal-fired utility industry.

116

Nitrogen enriched combustion of a natural gas internal combustion engine to reduce NO.sub.x emissions  

DOE Patents [OSTI]

A method and system for reducing nitrous oxide emissions from an internal combustion engine. An input gas stream of natural gas includes a nitrogen gas enrichment which reduces nitrous oxide emissions. In addition ignition timing for gas combustion is advanced to improve FCE while maintaining lower nitrous oxide emissions.

Biruduganti, Munidhar S. (Naperville, IL); Gupta, Sreenath Borra (Naperville, IL); Sekar, R. Raj (Naperville, IL); McConnell, Steven S. (Shorewood, IL)

2008-11-25T23:59:59.000Z

117

Nitrous oxide emissions from wastewater treatment processes  

Science Journals Connector (OSTI)

...samples followed by GC analysis has been used in both laboratory scale reactors and full-scale plants...two laboratory scale reactors. Foley et al. [23...measurements. Combining the analyses of both the microsensor...significantly increases the reliability of data. Similar to...

2012-01-01T23:59:59.000Z

118

Emissions and Air Quality Impacts of Freight Transportation Erica Bickford  

E-Print Network [OSTI]

Emissions and Air Quality Impacts of Freight Transportation by Erica Bickford A dissertation rights reserved. #12;Abstract Emissions and Air Quality Impacts of Freight Transportation Erica Bickford.S. transportation is the largest source of national nitrogen oxide (NOx) emissions and the third largest source

Wisconsin at Madison, University of

119

MEASURING GASEOUS EMISSIONS FROM STORED PIG SLURRY S. Espagnol1  

E-Print Network [OSTI]

2 MEASURING GASEOUS EMISSIONS FROM STORED PIG SLURRY S. Espagnol1 , L. Loyon2 , F. Guiziou2 , P to measure emissions factors of ammonia (NH3), nitrous oxide (N2O) methane (CH4) and carbon dioxide (CO2) from stored pig slurry and measured the variations of the emissions in time and space. In 2006, dynamic

Boyer, Edmond

120

Engine performance and exhaust emissions from a diesel  

E-Print Network [OSTI]

. Carbon monoxide emissions increased by an average 15% using B5 and by an average of 19% using B100. Hydrocarbon emissions decreased by 14% using B5 and by 26% using B100. Nitrogen oxide emissions decreased by four percent with B5, five percent with B20...

Powell, Jacob Joseph

2009-05-15T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Metal Oxides  

Science Journals Connector (OSTI)

Metal oxides are the class of materials having the widest application in gas sensors. This chapter presents information related to the application of various metal oxides in gas sensors designed on different p...

Ghenadii Korotcenkov

2013-01-01T23:59:59.000Z

122

Version 2 Global Fire Emissions Database Available  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Global Fire Emissions Database Available Global Fire Emissions Database Available The ORNL DAAC announces the release of the data set "Global Fire Emissions Database, Version 2 (GFEDv2)." This data set, which supersedes and replaces the Global Fire Emissions Database, Version 1 (GFEDv1), consists of 1 degree x 1 degree gridded monthly burned area, fuel loads, combustion completeness, and fire emissions of carbon (C), carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), non-methane hydrocarbons (NMHC), molecular hydrogen (H2), nitrogen oxides (NOx), nitrous oxide (N2O), particulate matter (PM2.5), total particulate matter (TPM), total carbon (TC), organic carbon (OC), and black carbon (BC) for the time period January 1997 - December 2004. For more information or to access this data set, please see the Vegetation

123

Vehicle Emission Basics | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Vehicle Emission Basics Vehicle Emission Basics Vehicle Emission Basics November 22, 2013 - 2:07pm Addthis Vehicle emissions are the gases emitted by the tailpipes of vehicles powered by internal combustion engines, which include gasoline, diesel, natural gas, and propane vehicles. Vehicle emissions are composed of varying amounts of: water vapor carbon dioxide (CO2) nitrogen oxygen pollutants such as: carbon monoxide (CO) nitrogen oxides (NOx) unburned hydrocarbons (UHCs) volatile organic compounds (VOCs) particulate matter (PM) A number of factors determine the composition of emissions, including the vehicle's fuel, the engine's technology, the vehicle's exhaust aftertreatment system, and how the vehicle operates. Emissions are also produced by fuel evaporation during fueling or even when vehicles are

124

Radon emissions  

Science Journals Connector (OSTI)

... SIR,-Wendy Barnaby (August 28) writes on the problem of radon emission from the tailings of uranium milling in Sweden. This problem would arise from ... that has to be treated. She describes Professor Robert O. Pohl's report that "radon can escape more easily from the broken ground of a mine than from an undisturbed ...

SVEN-ERIC BRUNNSJO

1975-10-09T23:59:59.000Z

125

Separate determination of PM10 emission factors of road traffic for tailpipe emissions and emissions from abrasion and resuspension processes  

Science Journals Connector (OSTI)

Little is known about the relevance of mechanically produced particles of road traffic from abrasion and resuspension processes in relation to the exhaust pipe particles. In this paper, emission factors of PM10 and PM1 for light and heavy-duty vehicles were derived for different representative traffic regimes from concentration differences of particles and nitrogen oxides (NOx) in ambient air upwind and downwind of busy roads, or alternatively of kerbsides and nearby background sites. Hereby, PM1 was interpreted as direct exhaust emissions and PM10-PM1 as mechanically produced emissions from abrasion and resuspension processes. The results show that abrasion and resuspension processes represent a significant part of the total primary PM10 emissions of road traffic. At sites with relatively undisturbed traffic flow they are in the same range as the exhaust pipe emissions. At sites with disturbed traffic flow due to traffic lights, emissions from abrasion/resuspension are even higher than those from the exhaust pipes.

Robert Gehrig; Matz Hill; Brigitte Buchmann; David Imhof; Ernest Weingartner; Urs Baltensperger

2004-01-01T23:59:59.000Z

126

Effects of Future Ship Emissions in the North Sea on Air Quality  

Science Journals Connector (OSTI)

By means of model simulations with the chemistry transport model CMAQ the influence of ship emissions in the North Sea on concentrations ... and nitrogen oxides over Europe was investigated. Ship emissions for th...

Armin Aulinger; Volker Matthias…

2014-01-01T23:59:59.000Z

127

Emissions Characterization from Advanced Combustion & Alternative Fuels -  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Emissions Characterization from Advanced Combustion & Emissions Characterization from Advanced Combustion & Alternative Fuels Exhaust emissions from engines operating in advanced combustion modes such as PCCI (Premixed Charge Compression Ignition) and HCCI (Homogeneous Charge Compression Ignition) are analyzed with an array of analytical tools. Furthermore, emissions from a variety of alternative fuels and mixtures thereof with conventional gasoline and diesel fuels are also measured. In addition to measuring the criteria pollutants nitrogen oxides (NOx), carbon monoxide (CO), hydrocarbons (HCs) are also measured and categorized based on chemistry. These chemical details of the emissions provide important information for optimizing combustion processes to maximize fuel efficiency while minimizing emissions

128

Non-Incineration Treatment to Reduce Benzene and VOC Emissions from Green Sand Molding Systems  

SciTech Connect (OSTI)

Final report describing laboratory, pilot scale and production scale evaluation of advanced oxidation systems for emissions and cost reduction in metal casting green sand systems.

Fred S. Cannon; Robert C. Voigt

2002-06-28T23:59:59.000Z

129

Mitigating greenhouse gas emissions: Voluntary reporting  

SciTech Connect (OSTI)

The Voluntary Reporting Program, developed pursuant to Section 1605(b) of the Energy Policy Act of 1992, permits corporations, government agencies, households, and voluntary organizations to report on their emissions of greenhouse gases, and on actions taken that have reduced or avoided emissions or sequestered carbon, to the Energy Information Administration (EIA). This, the second annual report of the Voluntary Reporting Program, describes information provided by the participating organizations on their aggregate emissions and emissions reductions, as well as their emissions reduction or avoidance projects, through 1995. This information has been compiled into a database that includes reports from 142 organizations and descriptions of 967 projects that either reduced greenhouse gas emissions or sequestered carbon. Fifty-one reporters also provided estimates of emissions, and emissions reductions achieved, for their entire organizations. The projects described actions taken to reduce emissions of carbon dioxide from energy production and use; to reduce methane and nitrous oxide emissions from energy use, waste management, and agricultural processes; to reduce emissions of halocarbons, such as CFCs and their replacements; and to increase carbon sequestration.

NONE

1997-10-01T23:59:59.000Z

130

nitrogen oxides | OpenEI  

Open Energy Info (EERE)

20 20 Varnish cache server Browse Upload data GDR 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142279720 Varnish cache server nitrogen oxides Dataset Summary Description Emissions from energy use in buildings are usually estimated on an annual basis using annual average multipliers. Using annual numbers provides a reasonable estimation of emissions, but it provides no indication of the temporal nature of the emissions. Therefore, there is no way of understanding the impact on emissions from load shifting and peak shaving technologies such as thermal energy storage, on-site renewable energy, and demand control. Source NREL Date Released April 11th, 2011 (3 years ago) Date Updated April 11th, 2011 (3 years ago)

131

Non-Petroleum-Based Fuels: Effects on Emissions Controls (Agreement...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Non-Petroleum-Based Fuels: Effects on Emissions Controls (Agreement Number 13425)NPBF Effects on PM OxidationNPBF Effects on EGR System Performance Non-Petroleum-Based Fuels:...

132

Preliminary GHG Emissions Inventory for the Slovak Republic  

Science Journals Connector (OSTI)

This paper presents preliminary results of a greenhouse gas emissions inventory for the Slovak Republic. The key gases included are carbon dioxide, methane, and nitrous oxide. Chlorofluorocarbons are excluded ...

Katarína Mare?kova; Pavol Bielek; Stanislav Kucirek…

1996-01-01T23:59:59.000Z

133

Optimization of Engine-out Emissions from a Diesel Engine to Meet Tier 2 Bin 5 Emission Limits  

Broader source: Energy.gov [DOE]

Drastic reduction of engine-out emissions and complicated aftertreatment system comprising of oxidation catalyst, particulate filter, and DeNOx catalyst are implemented to meet Tier 2 Bin 5 limits for U.S. market diesel engines.

134

Elastic emission polishing  

SciTech Connect (OSTI)

Elastic emission polishing, also called elastic emission machining (EEM), is a process where a stream of abrasive slurry is used to remove material from a substrate and produce damage free surfaces with controlled surface form. It is a noncontacting method utilizing a thick elasto-hydrodynamic film formed between a soft rotating ball and the workpiece to control the flow of the abrasive. An apparatus was built in the Center, which consists of a stationary spindle, a two-axis table for the workpiece, and a pump to circulate the working fluid. The process is controlled by a programmable computer numerical controller (CNC), which presently can operate the spindle speed and movement of the workpiece in one axis only. This apparatus has been used to determine material removal rates on different material samples as a function of time, utilizing zirconium oxide (ZrO{sub 2}) particles suspended in distilled water as the working fluid. By continuing a study of removal rates the process should become predictable, and thus create a new, effective, yet simple tool for ultra-precision mechanical machining of surfaces.

Loewenthal, M.; Loseke, K.; Dow, T.A.; Scattergood, R.O.

1988-12-01T23:59:59.000Z

135

Exhaust emissions from two intercity passenger locomotives  

SciTech Connect (OSTI)

To enhance the effectiveness of intercity passenger rail service in mitigating exhaust emissions in California, the California Department of Transportation (Caltrans) included limits on exhaust emissions in its intercity locomotive procurement specifications. Because there were no available exhaust emission test data on which emission reduction goals could be based, Caltrans funded a test program to acquire gaseous and particulate exhaust emissions data, along with smoke opacity data, from two state-of-the-art intercity passenger locomotives. The two passenger locomotives (an EMD F59PH and a GE DASH8-32BWH) were tested at the Association of American Railroads Chicago Technical Center. The EMD locomotive was equipped with a separate Detroit Diesel Corporation (DDC) 8V-149 diesel engine used to provide 480 V AC power for the trailing passenger cars. This DDC engine was also emission tested. These data were used to quantify baseline exhaust emission levels as a challenge to locomotive manufacturers to offer new locomotives with reduced emissions. Data from the two locomotive engines were recorded at standard fuel injection timing and with the fuel injection timing retarded 4 deg in an effort to reduce NO[sub x] emissions. Results of this emissions testing were incorporated into the Caltrans locomotive procurement process by including emission performance requirements in the Caltrans intercity passenger locomotive specification, and therefore in the procurement decision. This paper contains steady-state exhaust emission test results for hydrocarbons (HC), carbon monoxide (CO), oxides of nitrogen (NO[sub x]), and particulate matter (PM) from the two locomotives. Computed sulfur dioxide (SO[sub 2]) emissions are also given, and are based on diesel fuel consumption and sulfur content. Exhaust smoke opacity is also reported.

Fritz, S.G. (Southwest Research Inst., San Antonio, TX (United States). Dept. of Emissions Research)

1994-10-01T23:59:59.000Z

136

Global Fire Emissions Database, Version 3.1 Published  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Fire Emissions Database, Version 3.1 Published Fire Emissions Database, Version 3.1 Published The ORNL DAAC is pleased to announce the release of the Global Fire Emissions Database, Version 3.1: Global Fire Emissions Database, Version 3.1. Data set prepared by J.T. Randerson, G.R. van der Werf, L. Giglio, G.J. Collatz, and P.S. Kasibhatla. This data set provides monthly burned area, and monthly and annual fire emissions data from July 1996 to February 2012. Emissions data are available for carbon (C), dry matter (DM), carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), hydrogen (H2), nitrous oxide (N2O), nitrogen oxides (NOx), non-methane hydrocarbons (NMHC), organic carbon (OC), black carbon (BC), particulate matter 2.5 micron (PM2p5), total particulate matter (TPM), and sulfur dioxide (SO2) among others. The C4 fraction of

137

MOBILE6 Vehicle Emission Modeling Software | Open Energy Information  

Open Energy Info (EERE)

MOBILE6 Vehicle Emission Modeling Software MOBILE6 Vehicle Emission Modeling Software Jump to: navigation, search Tool Summary Name: MOBILE6 Agency/Company /Organization: United States Environmental Protection Agency Sector: Energy Focus Area: Transportation Topics: GHG inventory Resource Type: Software/modeling tools User Interface: Desktop Application Website: www.epa.gov/oms/m6.htm Cost: Free References: http://www.epa.gov/oms/m6.htm MOBILE6 is an emission factor model for predicting gram per mile emissions of Hydrocarbons (HC), Carbon Monoxide (CO), Nitrogen Oxides (NOx), Carbon Dioxide (CO2), Particulate Matter (PM), and toxics from cars, trucks, and motorcycles under various conditions. MOBILE6 is an emission factor model for predicting gram per mile emissions of Hydrocarbons (HC), Carbon Monoxide (CO), Nitrogen Oxides (NOx), Carbon

138

Kinetics of Diesel Nanoparticle Oxidation  

Science Journals Connector (OSTI)

The oxidation rates in air of diesel nanoparticles sampled directly from the exhaust stream of a medium-duty diesel engine were measured over the temperature range of 800?1140 °C using online aerosol techniques. ... Particulate emission from diesel engines is currently a topic of great concern from both pollution and public health standpoints. ... In addition, the fundamental carbon-to-hydrogen ratio may be different in diesel particles as compared to the commonly used surrogates (15). ...

Kelly J. Higgins; Heejung Jung; David B. Kittelson; Jeffrey T. Roberts; Michael R. Zachariah

2003-03-25T23:59:59.000Z

139

Vehicle Technologies Office: Emission Control R&D  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Emission Control R&D Emission Control R&D The Vehicle Technologies Office (VTO) supports research and development of aftertreatment technologies to control advanced combustion engine exhaust emissions. All engines that enter the vehicle market must comply with the Environmental Protection Agency's emissions regulations. Harmful pollutants in these emissions include: Carbon monoxide Nitrogen oxides Unburned hydrocarbons Volatile organic compounds (VOCs) Particulate matter The energy required for emission control often reduces vehicle fuel economy and increases vehicle cost. VTO's Emission Control R&D focuses on developing efficient, durable, low-cost emission control systems that complement new combustion strategies while minimizing efficiency losses. VTO often leverages the national laboratories' unique capabilities and facilities to conduct this research.

140

Steam Oxidation of Advanced Steam Turbine Alloys  

SciTech Connect (OSTI)

Power generation from coal using ultra supercritical steam results in improved fuel efficiency and decreased greenhouse gas emissions. Results of ongoing research into the oxidation of candidate nickel-base alloys for ultra supercritical steam turbines are presented. Exposure conditions range from moist air at atmospheric pressure (650°C to 800°C) to steam at 34.5 MPa (650°C to 760°C). Parabolic scale growth coupled with internal oxidation and reactive evaporation of chromia are the primary corrosion mechanisms.

Holcomb, Gordon R.

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Implications of Near-Term Coal Power Plant Retirement for SO2 and NOX and Life Cycle GHG Emissions  

Science Journals Connector (OSTI)

Implications of Near-Term Coal Power Plant Retirement for SO2 and NOX and Life Cycle GHG Emissions ... Life cycle GHG emissions were found to decrease by less than 4% in almost all scenarios modeled. ... Resulting changes in fuel use, life cycle greenhouse gas (GHG) emissions, and emissions of sulfur and nitrogen oxides are estimated. ...

Aranya Venkatesh; Paulina Jaramillo; W. Michael Griffin; H. Scott Matthews

2012-08-13T23:59:59.000Z

142

Fast cook-off testing in enclosed facilities with reduced emissions  

SciTech Connect (OSTI)

Sandia National Laboratories has utilized pool fires for over thirty years to subject military components, weapon mockups and hazardous material shipping containers to postulated transportation accident environments. Most of the tests have been performed in either open pools or wind shielded facilities with little control of visible smoke emissions. Because of the increased sensitivity of environmental issues and because wind generates the biggest uncontrollable effect on the thermal environment in open pool fires, enclosed test facilities with reduced visible emissions have been developed. The facilities are basically water cooled enclosures fitted with controlled air supply systems and high temperature afterburners. The purpose of this paper is to present our experience with both open and enclosed fires. In the first section, a review of the fire test facilities is given. A following section presents a mathematical model behind our approach to characterizing the fire environment. In the last section, data from open and closed fires are compared.

Nakos, J.T.; Kent, L.A.; Gill, W.; Sobolik, K.B.

1991-01-01T23:59:59.000Z

143

Innovative Clean Coal Technology (ICCT): Demonstration of Selective Catalytic Reduction (SCR) technology for the control of nitrogen oxide (NO{sub x}) emissions from high-sulfur coal-fired boilers. Quarterly report No. 6, October--December, 1991  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NOx) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NOx to convert it to nitrogen and water vapor.

Not Available

1992-02-01T23:59:59.000Z

144

Innovative Clean Coal Technology (ICCT): Demonstration of Selective Catalytic Reduction (SCR) technology for the control of nitrogen oxide (NO sub x ) emissions from high-sulfur coal-fired boilers  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NOx) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NOx to convert it to nitrogen and water vapor.

Not Available

1992-02-01T23:59:59.000Z

145

Demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NOx) emissions from high-sulfur coal-fired boilers. Quarterly report No. 5, July--September 1991  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NO{sub x}) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NO{sub x} to convert it to nitrogen and water vapor.

Not Available

1991-11-01T23:59:59.000Z

146

Innovative Clean Coal Technology (ICCT): Demonstration of Selective Catalytic Reduction (SCR) technology for the control of nitrogen oxide (NO{sub x}) emissions from high-sulfur coal-fired boilers. Quarterly report No. 2, October--December 1990  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide NO{sub x} control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NO{sub x} to convert it to nitrogen and water vapor.

Not Available

1991-02-01T23:59:59.000Z

147

Innovative Clean Coal Technology (ICCT): Demonstration of Selective Catalytic Reduction (SCR) technology for the control of nitrogen oxide (NO sub x ) emissions from high-sulfur coal-fired boilers  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide NO{sub x} control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NO{sub x} to convert it to nitrogen and water vapor.

Not Available

1991-02-01T23:59:59.000Z

148

Innovative clean coal technology (ICCT): Demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NO{sub x}) emissions from high-sulfur coal-fired boilers. Quarterly report No. 3, January--March 1991  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NOx) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NOx to convert it to nitrogen and water vapor.

Not Available

1991-07-01T23:59:59.000Z

149

Innovative clean coal technology (ICCT): Demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NO sub x ) emissions from high-sulfur coal-fired boilers  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NOx) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NOx to convert it to nitrogen and water vapor.

Not Available

1991-07-01T23:59:59.000Z

150

180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NOx) emissions from coal-fired boilers. Technical progress report, First quarter 1991  

SciTech Connect (OSTI)

This project is being conducted at Gulf Power Company`s Plant Lansing Smith Unit 2 (LS-2) located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NOx combustion technologies on NOx emissions and boiler performance. The stepwise approach that is being used to evaluate the NOx control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NOx concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NOx reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. This quarterly update provides a description of the flow modeling study. This modeling effort centers on evaluating the in-furnace flow and mixing phenomena for the various low NOx firing systems being demonstrated at LS-2. Testing on the 1/12 scale model of the LS-2 boiler and the 1/6 scale model of the overfire air ductwork was completed. The test matrix included an analysis of the overfire air ductwork and three different boiler configurations. This report also contains results from the Phase 1 baseline tests. Data from the diagnostic, performance, and verification tests are presented. In addition, NOx emissions data and unit load profiles collected during long-term testing are reported. At the full load condition, the baseline NOx emission level at LS-2 is 0.62 lb/mBtu.

Not Available

1991-12-31T23:59:59.000Z

151

180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NOx) emissions from coal-fired boilers. Technical progress report, Third quarter 1992  

SciTech Connect (OSTI)

The project is being conducted at Gulf Power Company`s Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NOx combustion technologies on NOx emissions and boiler performance. A target of achieving 50% NOx reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NOx control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NOx concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NOx reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. This technical progress report presents the LNCFS Level 1 long-term data collected during this quarter. In addition, a comparison of all the long-term emissions data that have been collected to date is included.

Not Available

1992-12-31T23:59:59.000Z

152

Vehicle Emissions Review - 2011  

Broader source: Energy.gov (indexed) [DOE]

Emissions Review - 2011 (so far) Tim Johnson October 4, 2011 DOE DEER Conference, Detroit JohnsonTV@Corning.com 2 Summary * California LD criteria emission regs are tightening....

153

Mercury emissions from municipal solid waste combustors. An assessment of the current situation in the United States and forecast of future emissions  

SciTech Connect (OSTI)

This report examines emissions of mercury (Hg) from municipal solid waste (MSW) combustion in the United States (US). It is projected that total annual nationwide MSW combustor emissions of mercury could decrease from about 97 tonnes (1989 baseline uncontrolled emissions) to less than about 4 tonnes in the year 2000. This represents approximately a 95 percent reduction in the amount of mercury emitted from combusted MSW compared to the 1989 mercury emissions baseline. The likelihood that routinely achievable mercury emissions removal efficiencies of about 80 percent or more can be assured; it is estimated that MSW combustors in the US could prove to be a comparatively minor source of mercury emissions after about 1995. This forecast assumes that diligent measures to control mercury emissions, such as via use of supplemental control technologies (e.g., carbon adsorption), are generally employed at that time. However, no present consensus was found that such emissions control measures can be implemented industry-wide in the US within this time frame. Although the availability of technology is apparently not a limiting factor, practical implementation of necessary control technology may be limited by administrative constraints and other considerations (e.g., planning, budgeting, regulatory compliance requirements, etc.). These projections assume that: (a) about 80 percent mercury emissions reduction control efficiency is achieved with air pollution control equipment likely to be employed by that time; (b) most cylinder-shaped mercury-zinc (CSMZ) batteries used in hospital applications can be prevented from being disposed into the MSW stream or are replaced with alternative batteries that do not contain mercury; and (c) either the amount of mercury used in fluorescent lamps is decreased to an industry-wide average of about 27 milligrams of mercury per lamp or extensive diversion from the MSW stream of fluorescent lamps that contain mercury is accomplished.

none,

1993-05-01T23:59:59.000Z

154

Seasonal variations in N2O emissions from central California  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Seasonal variations in N2O emissions from central California Seasonal variations in N2O emissions from central California Title Seasonal variations in N2O emissions from central California Publication Type Journal Article Year of Publication 2012 Authors Jeong, Seongeun, Chuanfeng Zhao, Arlyn E. Andrews, Edward J. Dlugokencky, Colm Sweeney, Laura Bianco, James M. Wilczak, and Marc L. Fischer Journal Geophysical Research Letters Volume 39 Issue 16 Keywords atmospheric transport, inverse modeling, nitrous oxide Abstract We estimate nitrous oxide (N2O) emissions from Central California for the period of December 2007 through November 2009 by comparing N2O mixing ratios measured at a tall tower (Walnut Grove, WGC) with transport model predictions based on two global a priori N2O emission models (EDGAR32 and EDGAR42). Atmospheric particle trajectories and surface footprints are computed using the Weather Research and Forecasting (WRF) and Stochastic Time-Inverted Lagrangian Transport (STILT) models. Regression analyses show that the slopes of predicted on measured N2O from both emission models are low, suggesting that actual N2O emissions are significantly higher than the EDGAR inventories for all seasons. Bayesian inverse analyses of regional N2O emissions show that posterior annual N2O emissions are larger than both EDGAR inventories by factors of 2.0 ± 0.4 (EDGAR32) and 2.1 ± 0.4 (EDGAR42) with seasonal variation ranging from 1.6 ± 0.3 to 2.5 ± 0.4 for an influence region of Central California within approximately 150 km of the tower. These results suggest that if the spatial distribution of N2O emissions in California follows the EDGAR emission models, then actual emissions are 2.7 ± 0.5 times greater than the current California emission inventory, and total N2O emissions account for 8.1 ± 1.4% of total greenhouse gas emissions from California.

155

Oxidation of Propane by Doped Nickel Oxides  

Science Journals Connector (OSTI)

... present study, however, indicate that in the absence of excess oxygen, direct oxidation of propane by the oxide lattice can occur.

D. W. McKEE

1964-04-11T23:59:59.000Z

156

NETL: IEP – Post-Combustion CO2 Emissions Control - Near-Zero Emissions  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Near-Zero Emissions Oxy-Combustion Flue Gas Purification Near-Zero Emissions Oxy-Combustion Flue Gas Purification Project No.: DE-NT0005341 Praxair oxy-combustion test equipment Praxair oxy-combustion test equipment. Praxair Inc. will develop a near-zero emissions flue gas purification technology for existing coal-fired power plants retrofit with oxy-combustion technology. Emissions of sulfur dioxide (SO2) and mercury (Hg) will be reduced by at least 99 percent, and nitrogen oxide (NOx) emissions will be reduced by greater than 90 percent without the need for wet flue gas desulfurization and selective catalytic reduction (SCR). Two separate processes are proposed depending on the sulfur content of the coal. For high-sulfur coal, SO2 and NOx will be recovered as product sulfuric acid and nitric acid, respectively, and Hg will be recovered as

157

EIA - Greenhouse Gas Emissions - Carbon Dioxide Emissions  

Gasoline and Diesel Fuel Update (EIA)

2. Carbon Dioxide Emissions 2. Carbon Dioxide Emissions 2.1. Total carbon dioxide emissions Annual U.S. carbon dioxide emissions fell by 419 million metric tons in 2009 (7.1 percent), to 5,447 million metric tons (Figure 9 and Table 6). The annual decrease-the largest over the 19-year period beginning with the 1990 baseline-puts 2009 emissions 608 million metric tons below the 2005 level, which is the Obama Administration's benchmark year for its goal of reducing U.S. emissions by 17 percent by 2020. The key factors contributing to the decrease in carbon dioxide emissions in 2009 included an economy in recession with a decrease in gross domestic product of 2.6 percent, a decrease in the energy intensity of the economy of 2.2 percent, and a decrease in the carbon intensity of energy supply of

158

Ultra Supercritical Steamside Oxidation  

SciTech Connect (OSTI)

Ultra supercritical (USC) power plants offer the promise of higher efficiencies and lower emissions, which are goals of the U.S. Department of Energy's Advanced Power Systems Initiatives. Most current coal power plants in the U.S. operate at a maximum steam temperature of 538 C. However, new supercritical plants worldwide are being brought into service with steam temperatures of up to 620 C. Current Advanced Power Systems goals include coal generation at 60% efficiency, which require steam temperatures of up to 760 C. This research examines the steamside oxidation of advanced alloys for use in USC systems, with emphasis placed on alloys for high- and intermediate-pressure turbine sections. Initial results of this research are presented.

Holcomb, Gordon R.; Cramer, Stephen D.; Covino, Bernard S., Jr.; Bullard, Sophie J.; Ziomek-Moroz, Malgorzata

2005-01-01T23:59:59.000Z

159

Trends in On-Road Vehicle Emissions of Ammonia  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Trends in On-Road Vehicle Emissions of Ammonia Trends in On-Road Vehicle Emissions of Ammonia Title Trends in On-Road Vehicle Emissions of Ammonia Publication Type Journal Article Year of Publication 2008 Authors Kean, Andrew J., David Littlejohn, George Ban-Weiss, Robert A. Harley, Thomas W. Kirchstetter, and Melissa M. Lunden Journal Atmospheric Environment Abstract Motor vehicle emissions of ammonia have been measured at a California highway tunnel in the San Francisco Bay area. Between 1999 and 2006, light-duty vehicle ammonia emissions decreased by 38 ± 6%, from 640 ± 40 to 400 ± 20 mg kg-1. High time resolution measurements of ammonia made in summer 2001 at the same location indicate a minimum in ammonia emissions correlated with slower-speed driving conditions. Variations in ammonia emission rates track changes in carbon monoxide more closely than changes in nitrogen oxides, especially during later evening hours when traffic speeds are highest. Analysis of remote sensing data of Burgard et al. (Environ Sci. Technol. 2006, 40, 7018-7022) indicates relationships between ammonia and vehicle model year, nitrogen oxides, and carbon monoxide. Ammonia emission rates from diesel trucks were difficult to measure in the tunnel setting due to the large contribution to ammonia concentrations in a mixed-traffic bore that were assigned to light-duty vehicle emissions. Nevertheless, it is clear that heavy-duty diesel trucks are a minor source of ammonia emissions compared to light-duty gasoline vehicles.

160

Enforcing Emissions Trading when Emissions Permits are Bankable  

Science Journals Connector (OSTI)

We propose enforcement strategies for emissions trading programs with bankable emissions permits that guarantee...

John K. Stranlund; Christopher Costello…

2005-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Practical implications of marine diesel engine emission regulations  

SciTech Connect (OSTI)

The main pollutants from marine diesel engines are oxides of nitrogen (NOx), sulfur oxides (SOx) and particulates (soot). However, the proposed marine diesel engine emission regulations will primarily focus on the levels of NOx and SOx. In the future, once the proposed regulations are met, the limits and levels of other emissions will come under increasing scrutiny, such as particulates, hydrocarbons and carbon monoxide. Regardless of the type of pollutant, there are generally two classes of emission control: (1) techniques that reduce the amount of pollutant formed in the combustion process, or (2) prevent the pollutants from reaching the atmosphere. Unfortunately, some of these control techniques will not be able to meet the incoming regulations. Therefore, this paper identifies the diesel engine emissions of concern, the impending regulations, and the merits of current and future emission control technologies required to meet these regulations.

Bowen, C.E.; Potter, I.J.; Reader, G.T. [Univ. of Calgary, Alberta (Canada). Dept. of Mechanical Engineering

1996-09-01T23:59:59.000Z

162

Excellent oxidation endurance of boron nitride nanotube field electron emitters  

SciTech Connect (OSTI)

Boron nitride nanotubes (BNNTs) are considered as a promising cold electron emission material owing to their negative electron affinity. BNNT field emitters show excellent oxidation endurance after high temperature thermal annealing of 600?°C in air ambient. There is no damage to the BNNTs after thermal annealing at a temperature of 600?°C and also no degradation of field emission properties. The thermally annealed BNNTs exhibit a high maximum emission current density of 8.39?mA/cm{sup 2} and show very robust emission stability. The BNNTs can be a promising emitter material for field emission devices under harsh oxygen environments.

Song, Yenan [Department of Micro/Nano Systems, Korea University, Seoul 136-713 (Korea, Republic of); Sun, Yuning; Hoon Shin, Dong; Nam Yun, Ki [School of Electrical Engineering, Korea University, Seoul 136-713 (Korea, Republic of); Song, Yoon-Ho [Nano Electron-Source Creative Research Center, Creative and Challenging Research Division, ETRI, Daejeon 305-700 (Korea, Republic of); Milne, William I. [Electrical Engineering Division, Engineering Department, Cambridge University, Cambridge CB3 0FA (United Kingdom); Jin Lee, Cheol, E-mail: cjlee@korea.ac.kr [Department of Micro/Nano Systems, Korea University, Seoul 136-713 (Korea, Republic of); School of Electrical Engineering, Korea University, Seoul 136-713 (Korea, Republic of)

2014-04-21T23:59:59.000Z

163

Measurement and Meaning of Oxidatively Modified DNA Lesions in Urine  

Science Journals Connector (OSTI)

...commercially available kits presently on the market. Two are available from JICA, named...oxidative stress-inducing agents, such as diesel emission particles or potassium bromate...Moller P, et al. Repeated inhalations of diesel exhaust particles and oxidatively damaged...

Marcus S. Cooke; Ryszard Olinski; and Steffen Loft

2008-01-01T23:59:59.000Z

164

EIA - Annual Energy Outlook 2009 - Emissions from Energy Use  

Gasoline and Diesel Fuel Update (EIA)

Emissions from Energy Use Emissions from Energy Use Annual Energy Outlook 2009 with Projections to 2030 Emissions from Energy Use Figure 81. Carbon diioxide emissions by sector and fuel, 2007 and 2030 (million metric tons). Need help, contact the National Energy Information Center at 202-586-8800. figure data Figure 82. Sulfur dioxide emissions from electricity generation, 1995-2030 (million short tons). Need help, contact the National Energy Information Center at 202-586-8800. figure data Figure 83. Nitrogen oxide emissions from electricity generation, 1995-2030 (million short tons). Need help, contact the National Energy Information Center at 202-586-8800. figure data Rate of Increase in Carbon Dioxide Emissions Slows in the Projections Even with rising energy prices, growth in energy use leads to increasing

165

Grain-size effects in nanoscaled electrolyte and cathode thin films for solid oxide fuel cells (SOFC).  

E-Print Network [OSTI]

??Due to their high energy conversion efficiencies and low emissions, Solid Oxide Fuel Cells (SOFCs) show promise as a replacement for combustion-based electrical generators at… (more)

Peters, Christoph

2009-01-01T23:59:59.000Z

166

Multiwavelength Thermal Emission  

E-Print Network [OSTI]

Multiwavelength Astronomy NASA #12;Thermal Emission #12;Thermal Emission Non-thermal p-p collisions Optical IR Radio/ Microwave sources of emission massive stars, WHIM, Ly many dust, cool objects-ray ~GeV Gamma-ray ~TeV sources of emission AGN, clusters, SNR, binaries, stars AGN (obscured), shocks

California at Santa Cruz, University of

167

Electrical Properties of Tungsten Oxide Films  

Science Journals Connector (OSTI)

... appear that the mechanism of electron emission with oxide films is different from that with roughened electrodes. This would be the case for short gaps if the electrons were drawn ... located on the upper surface of the film, as envisaged by Paetov1, while with roughened electrodes it is possible that photo-ionization can take place throughout the gap due to ...

F. LLEWELLYN JONES

1946-03-23T23:59:59.000Z

168

Demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NO{sub x}) emissions from high-sulfur coal-fired boilers. Quarterly report No. 8, April--June, 1992  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NO{sub x}) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NO{sub x} to convert it to nitrogen and water vapor. Although SCR is widely practiced in Japan and Europe, there are numerous technical uncertainties associated with applying SCR to US coals. These uncertainties include: (1) potential catalyst deactivation due to poisoning by trace metal species present in US coals that are not present in other fuels. (2) performance of the technology and effects on the balance-of-plant equipment in the presence of high amounts of SO{sub 2} and SO{sub 3}. (3) performance of a wide variety of SCR catalyst compositions, geometries and methods of manufacture under typical high-sulfur coal-fired utility operating conditions. These uncertainties will be explored by constructing a series of small-scale SCR reactors and simultaneously exposing different SCR catalysts to flue gas derived from the combustion of high sulfur U. S. coal.

Not Available

1992-08-01T23:59:59.000Z

169

Innovative clean coal technology (ICCT): Demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NO{sub x}) emissions from high-sulfur coal-fired boilers. Fourth quarterly progress report  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from US, Japanese and European catalyst suppliers on a high-sulfur US coal-fired boiler. SCR is a post-combustion nitrogen oxide (NO{sub x}) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NO{sub x} to convert it to nitrogen and water vapor. Although SCR is widely practiced in Japan and Europe, there are numerous technical uncertainties include: (1) potential catalyst deactivation due to poisoning by trace metal species present in US coals that are not present in other fuels; (2) performance of the technology and effects on the balance-of-plant equipment in the presence of high amounts of SO{sub 2} and SO{sub 3}; and (3) performance of a wide variety of SCR catalyst compositions, geometries and methods of manufacture under typical high-sulfur coal-fired utility operating conditions. These uncertainties will be explored by constructing a series of small-scale SCR reactors and simultaneously exposing different SCR catalysts to flue gas derived from the combustion of high sulfur US coal.

NONE

1992-12-31T23:59:59.000Z

170

Demonstration of Selective Catalytic Reduction (SCR) technology for the control of nitrogen oxide (NO{sub x}) emissions from high-sulfur coal-fired boilers. Technical progress report, first and second quarters 1994  

SciTech Connect (OSTI)

The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from U.S., Japanese and European catalyst suppliers on a high-sulfur U.S. coal-fired boiler. SCR is a post-combustion nitrogen oxide (NO{sub x}) control technology that involve injecting ammonia into the flue gas generated from coal combustion in a boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NO{sub x} to form nitrogen and water vapor. Although SCR is widely practiced in Japan and Europe on gas-, oil-, and low-sulfur coal-fired boilers, there are several technical uncertainties associated with applying SCR to U.S. coals. These uncertainties include: (1) potential catalyst deactivation due to poisoning by trace metal species present in U.S. coals that are not present in other fuels; (2) performance of the technology and effects on the balance-of-plant equipment in the presence of high amounts of SO{sub 2} and SO{sub 3}; and (3) performance of a wide variety of SCR catalyst compositions, geometries and methods of manufacture under typical high-sulfur coal-fired utility operating conditions. These uncertainties are being explored by operating a series of small-scale SCR reactors and simultaneously exposing different SCR catalysts to flue gas derived from the combustion of high sulfur U.S. coal. The project is being conducted in the following three phases: permitting, environmental monitoring plan and preliminary engineering; detailed design engineering and construction; and operation, testing, disposition and final report. The project was in the operation and testing phase during this reporting period. Accomplishments for this period are described.

NONE

1995-11-01T23:59:59.000Z

171

Demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NO{sub x}) emissions from high-sulfur coal-fired boilers. Draft final report  

SciTech Connect (OSTI)

The primary goal of this project was to demonstrate the use of Selective Catalytic Reduction (SCR) to reduce NO{sub x} emissions from pulverized-coal utility boilers using medium- to high-sulfur US coal. The prototype SCR facility, built in and around the ductwork of Plant Crist Unit 5, consisted of three large SCR reactor units (Reactors A, B, and C), each with a design capacity of 5,000 standard cubic feet per minute (scfm) of flue gas, and six smaller reactors (Reactors D through J), each with a design capacity of 400 scfm of flue gas. The three large reactors contained commercially available SCR catalysts as offered by SCR catalyst suppliers. These reactors were coupled with small-scale air preheaters to evaluate (1) the long-term effects of SCR reaction chemistry on air preheater deposit formation and (2) the impact of these deposits on the performance of air preheaters. The small reactors were used to test additional varieties of commercially available catalysts. The demonstration project was organized into three phases: (1) Permitting, Environmental Monitoring Plan (EMP) Preparation, and Preliminary Engineering; (2) Detail Design Engineering and Construction; and (3) Operation, Testing, Disposition, and Final Report Preparation. Section 2 discusses the planned and actual EMP monitoring for gaseous, aqueous, and solid streams over the course of the SCR demonstration project; Section 3 summarizes sampling and analytical methods and discusses exceptions from the methods specified in the EMP; Section 4 presents and discusses the gas stream monitoring results; Section 5 presents and discusses the aqueous stream monitoring results; Section 6 presents and discusses the solid stream monitoring results; Section 7 discusses EMP-related quality assurance/quality control activities performed during the demonstration project; Section 8 summarizes compliance monitoring reporting activities; and Section 9 presents conclusions based on the EMP monitoring results.

NONE

1996-06-14T23:59:59.000Z

172

Beyond Tailpipe Emissions  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Beyond Tailpipe Emissions Beyond Tailpipe Emissions Greenhouse Gas Emissions for Electric and Plug-In Hybrid Electric Vehicles Driving your vehicle can yield both greenhouse gas (GHG) emissions from your vehicle's tailpipe and GHG emissions related to the production of the fuel used to power your vehicle. For example, activities associated with fuel production such as feedstock extraction, feedstock transport to a processing plant, and conversion of feedstock to motor fuel, as well as distribution of the motor fuel, can all produce GHG emissions. The Fuel Economy and Environment Label provides a Greenhouse Gas Rating, from 1 (worst) to 10 (best), based on the vehicle's tailpipe carbon dioxide emissions only, and this rating does not reflect any GHG emissions associated with fuel production.

173

Emissions from Ships  

Science Journals Connector (OSTI)

...Turbine and Diesel) Engine Exhaust Emission...of relative fuel consumption. For commercial...Marine Diesel Engine and Gas Turbine...Turbine and Diesel) Engine Exhaust Emission...of relative fuel consumption. For commercial...

James J. Corbett; Paul Fischbeck

1997-10-31T23:59:59.000Z

174

Introduction to Emissions Trading  

Science Journals Connector (OSTI)

This chapter constitutes an introduction to emissions trading. First, we detail the latest developments ... Second, we introduce the main characteristics of emissions trading, be it in terms of spatial and...2 al...

Dr. Julien Chevallier

2012-01-01T23:59:59.000Z

175

Synthesis and characterizations of graphene oxide and reduced graphene oxide nanosheets  

SciTech Connect (OSTI)

Interest in graphene on its excellent mechanical, electrical, thermal and optical properties, it’s very high specific surface area, and our ability to influence these properties through chemical functionalization. Chemical reduction of graphene oxide is one of the main routes of preparation for large quantities of graphenes. Hydrazine hydrate used as reducing agent to prepare for the reduced graphene oxide (RGO). There are a number of methods for generating graphene and chemically modified graphene from natural graphite flakes, graphite derivative (such as graphite oxide) and graphite interaction compounds (i.e. expandable graphite). Here we review the use of colloidal suspensions of reduced graphene oxide (RGO) with large scalable, and is adaptable to a wide variety of applications. The graphene oxide (GO) and the reduced material (RGO) were characterized by XRD, UV-Vis spectroscopy, Thermo-gravimetric analysis (TGA), Raman spectroscopy and Field emission Scanning electron microscopy (FESEM) etc.

Venkanna, M., E-mail: venkanna.pcu@gmail.com; Chakraborty, Amit K., E-mail: venkanna.pcu@gmail.com [Carbon Nanotechnology Laboratory, Department of Physics, National Institute of Technology Durgapur, M.G. Avenue, Durgapur - 713209 (India)

2014-04-24T23:59:59.000Z

176

Evaluate Greenhouse Gas Emissions Profile  

Broader source: Energy.gov [DOE]

Evaluating a Federal agency's greenhouse gas (GHG) emissions profile means getting a solid understanding of the organization's largest emission categories, largest emission sources, and its potential for improvement.

177

Asphalt Oxidation Kinetics and Pavement Oxidation Modeling  

E-Print Network [OSTI]

Most paved roads in the United States are surfaced with asphalt. These asphalt pavements suffer from fatigue cracking and thermal cracking, aggravated by the oxidation and hardening of asphalt. This negative impact of asphalt oxidation on pavement...

Jin, Xin

2012-07-16T23:59:59.000Z

178

Exhaust and evaporative emissions from gasohol-type fuels  

SciTech Connect (OSTI)

An experimental study was conducted at the US Department of Energy's Bartlesville (Okla.) Energy Technology Center in cooperation with the Environmental Protection Agency to determine the characteristics of gasohol-type fuels with respect to exhaust and evaporative emissions. Five fuels, 2 gasolines (reference and commercial unleaded) and 3 gasohols (90% gasoline/10% ethanol) were tested in a fleet of 10 late-model automobiles. Six were equipped with oxidation catalysts and 4 were equipped with three-way catalysts. The results obtained from the 1978 Federal test procedure indicate that the addition of ethanol to the base gasoline, whether it is a reference fuel (Indolene) or a commercial fuel, has measurable effects on exhaust and evaporative emissions. However, on the average, the magnitude of these effects was generally within the 1978 emission standards established by the EPA. More specifically, the addition of ethanol, in the case of vehicles with oxidation catalysts, decreased hydrocarbons by an average of 27%, decreased carbon monoxide by 43%, decreased volumetric fuel economy by 3%, and increased oxides of nitrogen by 16%. Evaporative emissions were increased by 40%. In the case of vehicles with three-way catalysts, the addition of ethanol to the base fuel, on the average, decreased carbon monoxide by 7%, decreased fuel economy by 5%, increased hydrocarbons by 12%, increased oxides of nitrogen by 7%, and increased evaporative emissions by 49%.

Naman, T.M.; Allsup, J.R.

1980-08-01T23:59:59.000Z

179

Regulation of GHG emissions from transportation fuels: Emission quota versus emission intensity standard  

E-Print Network [OSTI]

1 ? ?) and ? respectively. GHG emissions per unit of blend1 ? ?)? i + ?? i Reduction in GHG emissions with respect toSeries Regulation of GHG emissions from transportation 

Rajagopal, Deepak

2010-01-01T23:59:59.000Z

180

ORIGINAL PAPER Short-term effect of tillage intensity on N2O and CO2 emissions  

E-Print Network [OSTI]

ORIGINAL PAPER Short-term effect of tillage intensity on N2O and CO2 emissions Pascal Boeckx negative to positive. We studied the short-term effect of tillage intensity on N2O and CO2 emissions. We site, an intermediately aerated Luvisol in Belgium, were similar. Nitrous oxide and CO2 emissions were

Paris-Sud XI, Université de

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

State Emissions Estimates  

Gasoline and Diesel Fuel Update (EIA)

Estimates of state energy-related carbon dioxide emissions Estimates of state energy-related carbon dioxide emissions Because energy-related carbon dioxide (CO 2 ) constitutes over 80 percent of total emissions, the state energy-related CO 2 emission levels provide a good indicator of the relative contribution of individual states to total greenhouse gas emissions. The U.S. Energy Information Administration (EIA) emissions estimates at the state level for energy-related CO 2 are based on data contained in the State Energy Data System (SEDS). 1 The state-level emissions estimates are based on energy consumption data for the following fuel categories: three categories of coal (residential/commercial, industrial, and electric power sector); natural gas; and ten petroleum products including-- asphalt and road oil, aviation gasoline, distillate fuel, jet fuel, kerosene, liquefied petroleum gases

182

Pollutant Emission Factors from Residential Natural Gas Appliances: A Literature Review  

E-Print Network [OSTI]

H. Bromly, Reduction of Nitrogen Dioxide Emissions from Gasthan 10 ! lm), and nitrogen dioxide ( N0 2) standards areare nitric oxide (NO) and nitrogen dioxide (N0 2); although,

Traynor, G.W.

2011-01-01T23:59:59.000Z

183

Low Emissions Aftertreatment and Diesel Emissions Reduction  

SciTech Connect (OSTI)

Detroit Diesel Corporation (DDC) has successfully completed a five-year Low Emissions Aftertreatment and Diesel Emissions Reduction (LEADER) program under a DOE project entitled: ''Research and Development for Compression-Ignition Direct-Injection Engines (CIDI) and Aftertreatment Sub-Systems''. The objectives of the LEADER Program were to: Demonstrate technologies that will achieve future federal Tier 2 emissions targets; and Demonstrate production-viable technical targets for engine out emissions, efficiency, power density, noise, durability, production cost, aftertreatment volume and weight. These objectives were successfully met during the course of the LEADER program The most noteworthy achievements in this program are listed below: (1) Demonstrated Tier 2 Bin 3 emissions target over the FTP75 cycle on a PNGV-mule Neon passenger car, utilizing a CSF + SCR system These aggressive emissions were obtained with no ammonia (NH{sub 3}) slip and a combined fuel economy of 63 miles per gallon, integrating FTP75 and highway fuel economy transient cycle test results. Demonstrated feasibility to achieve Tier 2 Bin 8 emissions levels without active NOx aftertreatment. (2) Demonstrated Tier 2 Bin 3 emissions target over the FTP75 cycle on a light-duty truck utilizing a CSF + SCR system, synergizing efforts with the DOE-DDC DELTA program. This aggressive reduction in tailpipe out emissions was achieved with no ammonia slip and a 41% fuel economy improvement, compared to the equivalent gasoline engine-equipped vehicle. (3) Demonstrated Tier 2 near-Bin 9 emissions compliance on a light-duty truck, without active NOx aftertreatment devices, in synergy with the DOE-DDC DELTA program. (4) Developed and applied advanced combustion technologies such as ''CLEAN Combustion{copyright}'', which yields simultaneous reduction in engine out NOx and PM emissions while also improving engine and aftertreatment integration by providing favorable exhaust species and temperature characteristics. These favorable emissions characteristics were obtained while maintaining performance and fuel economy. These aggressive emissions and performance results were achieved by applying a robust systems technology development methodology. This systems approach benefits substantially from an integrated experimental and analytical approach to technology development, which is one of DDCs core competencies Also, DDC is uniquely positioned to undertake such a systems technology development approach, given its vertically integrated commercial structure within the DaimlerChrysler organization. State-of-the-art analytical tools were developed targeting specific LEADER program objectives and were applied to guide system enhancements and to provide testing directions, resulting in a shortened and efficient development cycle. Application examples include ammonia/NO{sub x} distribution improvement and urea injection controls development, and were key contributors to significantly reduce engine out as well as tailpipe out emissions. Successful cooperation between DDC and Engelhard Corporation, the major subcontractor for the LEADER program and provider of state-of-the-art technologies on various catalysts, was another contributing factor to ensure that both passenger car and LD truck applications achieved Tier 2 Bin 3 emissions levels. Significant technical challenges, which highlight barriers of commercialization of diesel technology for passenger cars and LD truck applications, are presented at the end of this report.

None

2005-05-27T23:59:59.000Z

184

ASH EMISSIVITY CHARACTERIZATION AND PREDICTION  

SciTech Connect (OSTI)

The increased use of western subbituminous coals has generated concerns regarding highly reflective ash disrupting heat transfer in the radiant zone of pulverized-fuel boilers. Ash emissivity and reflectivity is primarily a function of ash particle size, with reflective deposits expected to consist of very small refractory ash materials such as CaO, MgO, or sulfate materials such as Na{sub 2}SO{sub 4}. For biomass fuels and biomass-coal blends, similar reflectivity issues may arise as a result of the presence of abundant organically associated calcium and potassium, which can transform during combustion to fine calcium, and potassium oxides and sulfates, which may act as reflective ash. The relationship of reflectivity to ash chemistry is a second-order effect, with the ash particle size distribution and melting point being determined by the size and chemistry of the minerals present in the starting fuel. Measurement of the emission properties of ash and deposits have been performed by several research groups (1-6) using both laboratory methods and measurements in pilot- and full-scale combustion systems. A review of the properties and thermal properties of ash stresses the important effect of ash deposits on heat transfer in the radiant boiler zone (1).

Christopher J. Zygarlicke; Donald P. McCollor; Charlene R. Crocker

1999-12-01T23:59:59.000Z

185

New gas turbine combustor supports emissions limits  

SciTech Connect (OSTI)

Gas Research Institute, in partnership with Allison Engine Co. of Indianapolis, has introduced a natural gas-fired, low-emissions combustor that it says will give customers of industrial gas turbines a least-cost approach for meeting US emissions regulations. The LE IV combustor uses dry, low-nitrogen oxides (DLN) technology to reduce emissions from the Allison 501K industrial gas turbine to 25 parts per million or less (corrected to 15 percent oxygen)--levels that are expected to meet pending federal emissions regulations. GRI is funding similar efforts with other manufacturers of turbines commonly used at pipeline compressor stations and industrial power generation sites. The Allison combustor features a dual operating mode. During the pilot mode of operation, fuel is directly injected into the combustor`s liner where it is consumed in a diffusion flame reaction. During higher power operation, the fuel and air are uniformly premixed in fuel-lean proportions to control NO{sub x} formation. In addition, optimum engine performance is maintained by the dry, lean-mixed combustion technology as it suppresses NO{sub x} formation in the turbine`s combustion section. An added advantage of the LE IV combustor is its ability to lower emissions without any adverse affect on engine performance and operations, according to GRI> The combustor is available as either a retrofit or as an option on a new engine.

NONE

1996-10-01T23:59:59.000Z

186

Carbon Emissions: Food Industry  

U.S. Energy Information Administration (EIA) Indexed Site

Food Industry Food Industry Carbon Emissions in the Food Industry The Industry at a Glance, 1994 (SIC Code: 20) Total Energy-Related Emissions: 24.4 million metric tons of carbon (MMTC) -- Pct. of All Manufacturers: 6.6% Total First Use of Energy: 1,193 trillion Btu -- Pct. of All Manufacturers: 5.5% Carbon Intensity: 20.44 MMTC per quadrillion Btu Energy Information Administration, "1994 Manufacturing Energy Consumption Survey" and Emissions of Greenhouse Gases in the United States 1998 Energy-Related Carbon Emissions, 1994 Source of Carbon Carbon Emissions (million metric tons) All Energy Sources 24.4 Net Electricity 9.8 Natural Gas 9.1 Coal 4.2 All Other Sources 1.3 Energy Information Administration, "1994 Manufacturing Energy Consumption Survey" and Emissions of Greenhouse Gases in the United States 1998

187

Carbon Emissions: Chemicals Industry  

U.S. Energy Information Administration (EIA) Indexed Site

Chemicals Industry Chemicals Industry Carbon Emissions in the Chemicals Industry The Industry at a Glance, 1994 (SIC Code: 28) Total Energy-Related Emissions: 78.3 million metric tons of carbon (MMTC) -- Pct. of All Manufacturers: 21.1% -- Nonfuel Emissions: 12.0 MMTC Total First Use of Energy: 5,328 trillion Btu -- Pct. of All Manufacturers: 24.6% Energy Sources Used As Feedstocks: 2,297 trillion Btu -- LPG: 1,365 trillion Btu -- Natural Gas: 674 trillion Btu Carbon Intensity: 14.70 MMTC per quadrillion Btu Energy Information Administration, "1994 Manufacturing Energy Consumption Survey" and Emissions of Greenhouse Gases in the United States 1998 Energy-Related Carbon Emissions, 1994 Source of Carbon Carbon Emissions (million metric tons) All Energy Sources 78.3 Natural Gas 32.1

188

NETL: Mercury Emissions Control  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Home > Technologies > Coal & Power Systems > Innovations for Existing Plants > Mercury Emissions Control Home > Technologies > Coal & Power Systems > Innovations for Existing Plants > Mercury Emissions Control Innovations for Existing Plants Mercury Emissions Control NETL managed the largest funded research program in the country to develop an in-depth understanding of fossil combustion-based mercury emissions. The program goal was to develop effective control options that would allow generators to comply with regulations. Research focus areas included measurement and characterization of mercury emissions, as well as the development of cost-effective control technologies for the U.S. coal-fired electric generating industry. Control Technologies Field Testing Phase I & II Phase III Novel Concepts APCD Co-benefits Emissions Characterization

189

Carbon Emissions: Paper Industry  

U.S. Energy Information Administration (EIA) Indexed Site

Paper Industry Paper Industry Carbon Emissions in the Paper Industry The Industry at a Glance, 1994 (SIC Code: 26) Total Energy-Related Emissions: 31.6 million metric tons of carbon (MMTC) -- Pct. of All Manufacturers: 8.5% Total First Use of Energy: 2,665 trillion Btu -- Pct. of All Manufacturers: 12.3% -- Pct. Renewable Energy: 47.7% Carbon Intensity: 11.88 MMTC per quadrillion Btu Renewable Energy Sources (no net emissions): -- Pulping liquor: 882 trillion Btu -- Wood chips and bark: 389 trillion Btu Energy Information Administration, "1994 Manufacturing Energy Consumption Survey" and Emissions of Greenhouse Gases in the United States 1998 Energy-Related Carbon Emissions, 1994 Source of Carbon Carbon Emissions (million metric tons) All Energy Sources 31.6 Net Electricity 11.0

190

emissions | OpenEI  

Open Energy Info (EERE)

emissions emissions Dataset Summary Description The New Zealand Ministry of Economic Development publishes an annual Energy Outlook, which presents projections of New Zealand's future energy supply, demand, prices and greenhouse gas emissions. The principle aim of these projections is to inform the national energy debate. Included here are the model results for emissions. The spreadsheet provides an interactive tool for selecting which model results to view, and which scenarios to evaluate; full model results for each scenario are also included. Source New Zealand Ministry of Economic Development Date Released Unknown Date Updated December 15th, 2010 (4 years ago) Keywords emissions New Zealand projections Data application/vnd.ms-excel icon 2010 New Zealand emissions outlook (xls, 1.2 MiB)

191

Power Plant Emission Reductions Using a Generation Performance Standard  

Gasoline and Diesel Fuel Update (EIA)

Power Plant Emission Reductions Power Plant Emission Reductions Using a Generation Performance Standard by J. Alan Beamon, Tom Leckey, and Laura Martin There are many policy instruments available for reducing power plant emissions, and the choice of a policy will affect compliance decisions, costs, and prices faced by consumers. In a previous analysis, the Energy Information Administration analyzed the impacts of power sector caps on nitrogen oxides (NO x ), sulfur dioxide (SO 2 ), and carbon dioxide (CO 2 ) emissions, assuming a policy instru- ment patterned after the SO 2 allowance program created in the Clean Air Act Amendments of 1990. 1 This report compares the results of that work with the results of an analysis that assumes the use of a dynamic generation performance standard (GPS) as an instrument for reducing CO 2 emissions. 2 In general, the results of the two analyses are similar: to reduce

192

Emissions of greenhouse gases in the United States 1997  

SciTech Connect (OSTI)

This is the sixth annual report on aggregate US national emissions of greenhouse gases. It covers emissions over the period 1990--1996, with preliminary estimates of emissions for 1997. Chapter one summarizes some background information about global climate change and the greenhouse effect. Important recent developments in global climate change activities are discussed, especially the third Conference of the Parties to the Framework Convention on Climate Change, which was held in December of 1997 in Kyoto, Japan. Chapters two through five cover emissions of carbon dioxide, methane, nitrous oxide, halocarbons and related gases, respectively. Chapter six describes potential sequestration and emissions of greenhouse gases as a result of land use changes. Six appendices are included in the report. 96 refs., 38 tabs.

NONE

1998-10-01T23:59:59.000Z

193

Saving Fuel, Reducing Emissions  

E-Print Network [OSTI]

would in turn lower PHEV fuel costs and make them morestretches from fossil-fuel- powered conventional vehiclesbraking, as do Saving Fuel, Reducing Emissions Making Plug-

Kammen, Daniel M.; Arons, Samuel M.; Lemoine, Derek M.; Hummel, Holmes

2009-01-01T23:59:59.000Z

194

Vehicle Emissions Review - 2012  

Broader source: Energy.gov (indexed) [DOE]

Vehicle Emissions Review - 2012 Tim Johnson October 16, 2012 2 Environmental Technologies Summary * Regulations - LEVIII finalized, Tier 3? RDE in Europe developing and very...

195

EMSL - emission spectra  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

emission-spectra en Structures and Stabilities of (MgO)n Nanoclusters. http:www.emsl.pnl.govemslwebpublicationsstructures-and-stabilities-mgon-nanoclusters

196

NETL: Emissions Characterization - CMU Emissions Characterization Study  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Source Emissions Characterization Study Source Emissions Characterization Study The emissions characterization study is being performed in conjunction with the Pittsburgh Air Quality Study [PDF-744KB], a larger effort that includes ambient measurements and atmospheric modeling of the Pittsburgh region. The main objectives of this portion of the study are: To achieve advanced characterization of the PM in the Pittsburgh region. Measurements include the PM size, surface, volume, and mass distribution; chemical composition as a function of size and on a single particle basis; temporal and spatial variability. To obtain accurate current fingerprints of the major primary PM sources in the Pittsburgh region using traditional filter-based sampling and state-of-the-art techniques such as dilution sampling and single particle analysis using mass spectroscopy and LIBS.

197

Oxidation of advanced steam turbine alloys  

SciTech Connect (OSTI)

Advanced or ultra supercritical (USC) steam power plants offer the promise of higher efficiencies and lower emissions. Current goals of the U.S. Department of Energy’s Advanced Power Systems Initiatives include coal generation at 60% efficiency, which would require steam temperatures of up to 760°C. This research examines the steamside oxidation of advanced alloys for use in USC systems, with emphasis placed on alloys for high- and intermediate-pressure turbine sections.

Holcomb, G.R.; Covino, B.S., Jr.; Bullard, S.J.; Ziomek-Moroz, M.

2006-03-01T23:59:59.000Z

198

Global and regional drivers of accelerating CO2 emissions  

Science Journals Connector (OSTI)

...emissions from fossil-fuel combustion and industrial...flux from fossil fuel combustion and industrial processes...sources: national-level combustion of solid, liquid...oxidation of nonfuel hydrocarbons; and fuel from...renewables, mainly as heat from biomass...

Michael R. Raupach; Gregg Marland; Philippe Ciais; Corinne Le Quéré; Josep G. Canadell; Gernot Klepper; Christopher B. Field

2007-01-01T23:59:59.000Z

199

Performance and emission enhancements of a variable geometry turbocharger on a heavy-duty diesel engine  

Science Journals Connector (OSTI)

Variable Geometry Turbochargers (VGTs) have emerged in the heavy-duty diesel market with the simultaneous introduction of Exhaust Gas Recirculation (EGR) in meeting emission standards. From a military perspective, VGTs offer considerable promise of improving low speed torque and overall fuel economy. Despite these gains, nitric oxides (NOx) emissions generally increase with increased boost. During times when the military can reduce its environmental impact, VGTs can drive EGR and counter the increase in NOx emissions with relatively minor penalty in particulate matter (PM) emissions. This study highlights the performance and emission enhancements enabled by a VGT on a heavy-duty diesel engine.

Timothy J. Jacobs; Chad Jagmin; Wesley J. Williamson; Zoran S. Filipi; Dennis N. Assanis; Walter Bryzik

2008-01-01T23:59:59.000Z

200

Apparatus for photocatalytic destruction of internal combustion engine emissions during cold start  

DOE Patents [OSTI]

A method and apparatus for the destruction of emissions from an internal combustion engine wherein a substrate coated with TiO.sub.2 is exposed to a light source in the exhaust system of an internal combustion engine thereby catalyzing oxidation/reduction reactions between gaseous hydrocarbons, carbon monoxide, nitrogen oxides and oxygen in the exhaust of the internal combustion engine.

Janata, Jiri (Richland, WA); McVay, Gary L. (Richland, WA); Peden, Charles H. (West Richland, WA); Exarhos, Gregory J. (Richland, WA)

1998-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Oxidation of propylene over copper oxide catalysts  

E-Print Network [OSTI]

to the study of propylene oxidation. Dunlop (17) reported that small quantities of iron compounds substantially enhanced the catalytic activity of chromia-alumina catalysts with respect to propylene oxidation, Woodharn (72) has suggested that under... between 360 C and 430oC the rate of propane oxidation decreases as the teznperature is increased, and the rate of conversion to olefins, especially propylene, becomes progressively greater. Above 430 C the proportion of propane converted to ethylene in...

Billingsley, David Stuart

2012-06-07T23:59:59.000Z

202

REAL-WORLD EFFICACY OF HEAVY DUTY DIESEL TRUCK NOX AND PM EMISSIONS CONTROLS  

E-Print Network [OSTI]

are International. b DOC = Diesel Oxidation Catalyst; DPF = Diesel Particulate Filter; EGR = Exhaust GasREAL-WORLD EFFICACY OF HEAVY DUTY DIESEL TRUCK NOX AND PM EMISSIONS CONTROLS Gurdas Sandhu H 26-28, 2012 #12;2 Objectives 1. Quantify inter-run variability in exhaust emission rates 2. Assess

Frey, H. Christopher

203

Catalysts for Lean Engine Emission Control - Emissions & Emission Controls  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Catalysts for Lean Engine Emission Control Catalysts for Lean Engine Emission Control Catalysts for controlling NOx from lean engines are studied in great detail at FEERC. Lean NOx Traps (LNTs) and Selective Catalytic Reduction (SCR) are two catalyst technologies of interest. Catalysts are studied from the nanoscale to full scale. On the nanoscale, catalyst powders are analyzed with chemisorptions techniques to determine the active metal surface area where catalysis occurs. Diffuse Reflectance Infrared Fourier Transform (DRIFT) spectroscopy is used to observe the chemical reactions occurring on the catalyst surface during catalyst operation. Both powder and coated catalyst samples are analyzed on bench flow reactors in controlled simulated exhaust environments to better characterize the chemical

204

Air Emission Inventory for the INEEL -- 1999 Emission Report  

SciTech Connect (OSTI)

This report presents the 1999 calendar year update of the Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL Air Emission Inventory documents sources and emissions of nonradionuclide pollutants from operations at the INEEL. The report describes the emission inventory process and all of the sources at the INEEL, and provides nonradionuclide emissions estimates for stationary sources.

Zohner, Steven K

2000-05-01T23:59:59.000Z

205

Observation of green emission from Ce3+ doped gadolinium oxide...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

freshly-prepared Gd2O3 undoped nanoparticles which is attributed to the stabilizer, polyethylene glycol biscarboxymethyl ether. Upon aging, the undoped particles show similar...

206

Nitrous oxide emission from denitrification in stream and river networks  

Science Journals Connector (OSTI)

...82071; e Environmental Sciences Division, Oak Ridge National Laboratory , Oak Ridge, TN 37831; f Department of Ecology and Evolutionary Biology...experiments on their lands. We also acknowledge the many workers who helped with the Lotic Intersite Nitrogen experiments...

Jake J. Beaulieu; Jennifer L. Tank; Stephen K. Hamilton; Wilfred M. Wollheim; Robert O. Hall; Jr.; Patrick J. Mulholland; Bruce J. Peterson; Linda R. Ashkenas; Lee W. Cooper; Clifford N. Dahm; Walter K. Dodds; Nancy B. Grimm; Sherri L. Johnson; William H. McDowell; Geoffrey C. Poole; H. Maurice Valett; Clay P. Arango; Melody J. Bernot; Amy J. Burgin; Chelsea L. Crenshaw; Ashley M. Helton; Laura T. Johnson; Jonathan M. O'Brien; Jody D. Potter; Richard W. Sheibley; Daniel J. Sobota; Suzanne M. Thomas

2011-01-01T23:59:59.000Z

207

Oxide coated silicon tip arrays for electron emission.  

E-Print Network [OSTI]

??The study of cold cathode materials is currently an active topic of research due to widespread and important applications of these materials in products such… (more)

Bian, Haijiao.

2011-01-01T23:59:59.000Z

208

UK emissions of the greenhouse gas nitrous oxide  

Science Journals Connector (OSTI)

...other land use, (v) waste, and (vi) other sources...forestry (LULUCF) and waste are similarly proportioned...8 per cent and manure storage systems for 6 per cent...is reported here from long-term monitoring of greenhouse...are still not enough long-term datasets to provide the...

2012-01-01T23:59:59.000Z

209

UK emissions of the greenhouse gas nitrous oxide  

Science Journals Connector (OSTI)

...ranges from 33 to 170 per cent for fuel combustion processes and 195 per cent for other combustion processes (annex 7 of MacCarthy et al. [11...manure storage and N fertilizers. Combustion processes are the main source of NO x and microbial...

2012-01-01T23:59:59.000Z

210

Mechanistic, sensitivity, and uncertainty studies of the atmospheric oxidation of dimethylsulfide  

E-Print Network [OSTI]

The global-scale emissions and reactivity of dimethylsulfide (CH3SCH3, DMS) make it an integral component in the atmospheric sulfur cycle. DMS is rapidly oxidized in the atmosphere by a complex gas-phase mechanism involving ...

Lucas, Donald David, 1969-

2003-01-01T23:59:59.000Z

211

Mechanism of oxygen reduction reaction on transition metal oxide catalysts for high temperature fuel cells  

E-Print Network [OSTI]

The solid oxide fuel cell (SOFC) with its high energy conversion efficiency, low emissions, silent operation and its ability to utilize commercial fuels has the potential to create a large impact on the energy landscape. ...

La O', Gerardo Jose Cordova

2008-01-01T23:59:59.000Z

212

FETC Programs for Reducing Greenhouse Gas Emissions  

SciTech Connect (OSTI)

Mark Twain once quipped that everyone talks about the weather but no one does anything about it. With interest in global climate change on the rise, researchers in the fossil-energy sector are feeling the heat to provide new technology to permit continued use of fossil fuels but with reduced emissions of so-called `greenhouse gases.` Three important greenhouse gases, carbon dioxide, methane, and nitrous oxide, are released to the atmosphere in the course of recovering and combusting fossil fuels. Their importance for trapping radiation, called forcing, is in the order given. In this report, we briefly review how greenhouse gases cause forcing and why this has a warming effect on the Earth`s atmosphere. Then we discuss programs underway at FETC that are aimed at reducing emissions of methane and carbon dioxide.

Ruether, J.A.

1998-02-01T23:59:59.000Z

213

Solid Oxide Fuel Cells  

Science Journals Connector (OSTI)

A Solid Oxide Fuel Cell (SOFC) is typically composed of two porous electrodes, interposed between an electrolyte made of a particular solid oxide ceramic material. The system originates from the work of Nernst...

Nigel M. Sammes; Roberto Bove; Jakub Pusz

2006-01-01T23:59:59.000Z

214

Nanoparticle Emissions from Internal Combustion Engines | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Nanoparticle Emissions from Internal Combustion Engines Nanoparticle Emissions from Internal Combustion Engines 2004 Diesel Engine Emissions Reduction (DEER) Conference...

215

Materials Applications of Photoelectron Emission Microscopy....  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Applications of Photoelectron Emission Microscopy. Materials Applications of Photoelectron Emission Microscopy. Abstract: Photoelectron emission microscopy (PEEM) is a versatile...

216

Spontaneous Emission Rate Enhancement Using Optical Antennas  

E-Print Network [OSTI]

of  Spontaneous  Emission  in  a  Semiconductor  nanoLED,”  emission  rate  enhancement  using  the  Fluorescent  Emission  by  Lattice   Resonances  in  

Kumar, Nikhil

2013-01-01T23:59:59.000Z

217

Emission Abatement System  

DOE Patents [OSTI]

Emission abatement system. The system includes a source of emissions and a catalyst for receiving the emissions. Suitable catalysts are absorber catalysts and selective catalytic reduction catalysts. A plasma fuel converter generates a reducing gas from a fuel source and is connected to deliver the reducing gas into contact with the absorber catalyst for regenerating the catalyst. A preferred reducing gas is a hydrogen rich gas and a preferred plasma fuel converter is a plasmatron. It is also preferred that the absorber catalyst be adapted for absorbing NO.sub.x.

Bromberg, Leslie (Sharon, MA); Cohn, Daniel R. (Chestnut Hill, MA); Rabinovich, Alexander (Swampscott, MA)

2003-05-13T23:59:59.000Z

218

Emission control cost-effectiveness of alternative-fuel vehicles  

SciTech Connect (OSTI)

Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquefied petroleum gas, compressed natural gas, and electricity. Vehicle emission estimates included both exhaust and evaporative emissions for air pollutants of hydrocarbon, carbon monoxide, nitrogen oxides, and air-toxic pollutants of benzene, formaldehyde, 1,3-butadiene, and acetaldehyde. Vehicle life-cycle cost estimates accounted for vehicle purchase prices, vehicle life, fuel costs, and vehicle maintenance costs. Emission control cost-effectiveness presented in dollars per ton of emission reduction was calculated for each alternative-fuel vehicle types from the estimated vehicle life-cycle emission reductions and costs. Among various alternative-fuel vehicle types, compressed natural gas vehicles are the most cost-effective vehicle type in controlling vehicle emissions. Dedicated methanol vehicles are the next most cost-effective vehicle type. The cost-effectiveness of electric vehicles depends on improvements in electric vehicle battery technology. With low-cost, high-performance batteries, electric vehicles are more cost-effective than methanol, ethanol, and liquified petroleum gas vehicles.

Wang, Q. [Argonne National Lab., IL (United States); Sperling, D.; Olmstead, J. [California Univ., Davis, CA (United States). Inst. of Transportation Studies

1993-06-14T23:59:59.000Z

219

Task 1: Steam Oxidation,”  

SciTech Connect (OSTI)

Need to improve efficiency, decrease emissions (esp. CO2) associated with the continued use of coal for power generation

I. G. Wright and G. R. Holcomb

2009-03-01T23:59:59.000Z

220

EPA Emissions | ornl.gov  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

EPA Emissions ORNL research informs new EPA emissions standards July 11, 2014 Oak Ridge National Laboratory (ORNL) has developed a streamlined method for determining vehicle...

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Emission Standards for Contaminants (Iowa)  

Broader source: Energy.gov [DOE]

These regulations list emissions standards for various contaminants, and contain special requirements for anaerobic lagoons. These regulations also describe alternative emissions limits, which may...

222

Engines - Emissions Assessment  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

EPRI Hybrid Electric Vehicle Working Group: HEV Costs and Emissions EPRI Hybrid Electric Vehicle Working Group: HEV Costs and Emissions Hybrid electric vehicles (HEVs) are attractive options for increasing vehicle fuel economy and reducing emissions of criteria pollutants and greenhouse gases. Two automobile manufacturers have already introduced HEVs, and other manufacturers are planning to introduce their own models. One available HEV combines mass reduction (also applicable to conventional vehicles) with idle-stop, regenerative braking, and electric-drive assist to achieve a fuel economy more than 2.5 times the current Corporate Average Fuel Economy (CAFE) standard. The second HEV combines idle-stop, regenerative braking, electric assist acceleration, and continuously variable transmission (CVT) to achieve a fuel economy of more than twice the current CAFÉ standard, qualifying as a super ultra-low emissions vehicle (SULEV).

223

Gas Turbine Emissions  

E-Print Network [OSTI]

Historically, preliminary design information regarding gas turbine emissions has been unreliable, particularly for facilities using steam injection and other forms of Best Available Control Technology (BACT). This was probably attributed to the lack...

Frederick, J. D.

224

Photon enhanced thermionic emission  

DOE Patents [OSTI]

Photon Enhanced Thermionic Emission (PETE) is exploited to provide improved efficiency for radiant energy conversion. A hot (greater than 200.degree. C.) semiconductor cathode is illuminated such that it emits electrons. Because the cathode is hot, significantly more electrons are emitted than would be emitted from a room temperature (or colder) cathode under the same illumination conditions. As a result of this increased electron emission, the energy conversion efficiency can be significantly increased relative to a conventional photovoltaic device. In PETE, the cathode electrons can be (and typically are) thermalized with respect to the cathode. As a result, PETE does not rely on emission of non-thermalized electrons, and is significantly easier to implement than hot-carrier emission approaches.

Schwede, Jared; Melosh, Nicholas; Shen, Zhixun

2014-10-07T23:59:59.000Z

225

Fuel Consumption and Emissions  

Science Journals Connector (OSTI)

Calculating fuel consumption and emissions is a typical offline analysis ... simulations or real trajectory data) and the engine speed (as obtained from gear-shift schemes ... as input and is parameterized by veh...

Martin Treiber; Arne Kesting

2013-01-01T23:59:59.000Z

226

Intelligent field emission arrays  

E-Print Network [OSTI]

Field emission arrays (FEAs) have been studied extensively as potential electron sources for a number of vacuum microelectronic device applications. For most applications, temporal current stability and spatial current ...

Hong, Ching-yin, 1973-

2003-01-01T23:59:59.000Z

227

Carbon Dioxide Emissions  

Science Journals Connector (OSTI)

Abating greenhouse gas (GHG) emissions on a national level involves substantial investment efforts, though part of these may be regained soon.1 On a global level, the costs of the available options are likely to ...

Catrinus J. Jepma; Che Wah Lee

1995-01-01T23:59:59.000Z

228

Field emission electron source  

DOE Patents [OSTI]

A novel field emitter material, field emission electron source, and commercially feasible fabrication method is described. The inventive field emission electron source produces reliable electron currents of up to 400 mA/cm.sup.2 at 200 volts. The emitter is robust and the current it produces is not sensitive to variability of vacuum or the distance between the emitter tip and the cathode. The novel emitter has a sharp turn-on near 100 volts.

Zettl, Alexander Karlwalter (Kensington, CA); Cohen, Marvin Lou (Berkeley, CA)

2000-01-01T23:59:59.000Z

229

Evaluation of landfill gas production and emissions in a MSW large-scale Experimental Cell in Brazil  

Science Journals Connector (OSTI)

Landfill gas (LFG) emissions from municipal solid waste (MSW) landfills are an important environmental concern in Brazil due to the existence of several uncontrolled disposal sites. A program of laboratory and field tests was conducted to investigate gas generation in and emission from an Experimental Cell with a 36,659-ton capacity in Recife/PE – Brazil. This investigation involved waste characterisation, gas production and emission monitoring, and geotechnical and biological evaluations and was performed using three types of final cover layers. The results obtained in this study showed that waste decomposes 4–5 times faster in a tropical wet climate than predicted by traditional first-order models using default parameters. This fact must be included when considering the techniques and economics of projects developed in tropical climate countries. The design of the final cover layer and its geotechnical and biological behaviour proved to have an important role in minimising gas emissions to the atmosphere. Capillary and methanotrophic final cover layers presented lower CH4 flux rates than the conventional layer.

Felipe Jucá Maciel; José Fernando Thomé Jucá

2011-01-01T23:59:59.000Z

230

Nitrous Oxide Fluxes from the Gulf of Mexico "Dead Zone" Primary Investigator: Craig Stow -NOAA GLERL  

E-Print Network [OSTI]

forecasts require accurate estimates of greenhouse gas emission rates. Currently, there are few measurements Management Research Laboratory Overview Nitrous oxide is a potent greenhouse gas with a global warming oxide is a potent greenhouse gas with a global warming potential ~300 times that of carbon dioxide

231

Diesel exhaust emissions from engines for use in underground mines  

SciTech Connect (OSTI)

Experimental data were obtained from two medium-duty diesel engines derated to qualify for use in underground mines. Gaseous and particulate emissions from these engines were measured and results provide information on the effect of exhaust treatment devices on the emissions. The devices in the study were a catalyst, a particulate trap, and an exhaust gas cooler of the water scrubber type. Emission levels of carbon monoxide and hydrocarbons were observed to be very low in comparison with emission levels of comparable engines in full-rated operation. Oxides of nitrogen and benzo(a)pyrene content of the exhaust also were found to be somewhat low in comparison with previous findings. For particulate reduction, the combination of a particulate trap and a scrubber was observed to be the most effective combination tried; in some cases, over 60% particulate reduction was effected by the trap-scrubber combination.

Eccleston, B.H.; Seizinger, D.E.; Clingenpeel, J.M.

1981-04-01T23:59:59.000Z

232

Wildland fire emissions, carbon, and climate: Emission factors Shawn Urbanski  

E-Print Network [OSTI]

Wildland fire emissions, carbon, and climate: Emission factors Shawn Urbanski Missoula Fire burning Greenhouse gases Emission factors a b s t r a c t While the vast majority of carbon emitted wildland fire greenhouse gas and aerosol (organic aerosol (OA) and black carbon (BC)) emission inventories

233

Advanced Petroleum-Based Fuels -- Diesel Emissions Control Project (APBF-DEC): Lubricants Project, Phase 2 Final Report  

SciTech Connect (OSTI)

This report summarizes the results of the second phase of a lubricants project, which investigated the impact of engine oil formulation on diesel vehicle emissions and the performance of a nitrogen oxide adsorber catalyst (NAC).

Not Available

2006-06-01T23:59:59.000Z

234

Reduction of Multi-pollutant Emissions from Industrial Sectors: The U.S. Cement Industry – A Case Study  

Science Journals Connector (OSTI)

Sulfur dioxide (SO2) emissions from cement kilns result from the sulfur in the fuel and the sulfur in the feed materials. Sulfur in the fuel will oxidize to SO2during pyroprocessing and a significant amount is li...

Ravi K. Srivastava; Samudra Vijay…

2011-01-01T23:59:59.000Z

235

Arabidopsis Nonsymbiotic Hemoglobin AHb1 Modulates Nitric Oxide Bioactivity  

Science Journals Connector (OSTI)

...used as control and showed a rate of NADPH oxidation that was...detector CLD 770 AL ppt (Eco-Physics, Munich, Germany) by a vacuum...excitation filter, 515-nm long-pass emission filter). Data acquired...The influence of delivery rate on the chemistry and biological...

Michele Perazzolli; Paola Dominici; Maria C. Romero-Puertas; Elisa Zago; Jürgen Zeier; Masatoshi Sonoda; Chris Lamb; Massimo Delledonne

2004-09-14T23:59:59.000Z

236

Oxidation in Environments with Elevated CO2 Levels  

SciTech Connect (OSTI)

Efforts to reduce greenhouse gas emissions from fossil energy power productions focus primarily on either pre- or post-combustion removal of CO2. The research presented here examines corrosion and oxidation issues associated with two types of post-combustion CO2 removal processes—oxyfuel combustion in refit boilers and oxyfuel turbines.

Gordon H. Holcomb

2009-05-01T23:59:59.000Z

237

Role of Moisture in Adsorption, Photocatalytic Oxidation, and  

E-Print Network [OSTI]

various Hg emission sources. A novel low-cost methodology using titanium dioxide (TiO2) nanoparticlesRole of Moisture in Adsorption, Photocatalytic Oxidation, and Reemission of Elemental Mercury gas. Without UV irradiation, Hg0 adsorption was found to be insignificant, but it could be enhanced

Li, Ying

238

Diesel Soot Oxidation with NO2:? Engine Experiments and Simulations  

Science Journals Connector (OSTI)

Diesel Soot Oxidation with NO2:? Engine Experiments and Simulations ... Particulate filtration in the exhaust system of diesel engines is increasingly gaining in importance for both light- and heavy-duty applications. ... The reaction rates are, in general, in the same order of magnitude with the engine-out soot emission rates. ...

Ioannis P. Kandylas; Onoufrios A. Haralampous; Grigorios C. Koltsakis

2002-09-20T23:59:59.000Z

239

Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Data Report No. 1  

SciTech Connect (OSTI)

The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NO{sub x}) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim data report summarizes results as of August, 1999, on the status of the test programs being conducted on three technologies: lean-NO{sub x} catalysts, diesel particulate filters and diesel oxidation catalysts.

DOE; ORNL; NREL; EMA; MECA

1999-08-15T23:59:59.000Z

240

Comparison of the Catalytic Oxidation Reaction on Graphene Oxide and Reduced Graphene Oxide  

E-Print Network [OSTI]

Comparison of the Catalytic Oxidation Reaction on Graphene Oxide and Reduced Graphene Oxide Laboratory (PAL), Pohang 790-784, Republic of Korea ABSTRACT: The capacities of graphene oxide (GO) and reduced graphene oxide (rGO) films grown on silicon substrate to cause the aniline to azobenzene oxidation

Kim, Sehun

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

SRC burn test in 700-hp oil-designed boiler. Annex Volume C. Boiler emission report. Final technical report  

SciTech Connect (OSTI)

The Solvent-Refined Coal (SRC) test burn program was conducted at the Pittsburgh Energy Technology Center (PETC) located in Bruceton, Pa. One of the objectives of the study was to determine the feasibility of burning SRC fuels in boilers set up for fuel oil firing and to characterize emissions. Testing was conducted on the 700-hp oil-fired boiler used for research projects. No. 6 fuel oil was used for baseline data comparison, and the following SRC fuels were tested: SRC Fuel (pulverized SRC), SRC Residual Oil, and SRC-Water Slurry. Uncontrolled particulate emission rates averaged 0.9243 lb/10/sup 6/ Btu for SRC Fuel, 0.1970 lb/10/sup 6/ Btu for SRC Residual Oil, and 0.9085 lb/10/sup 6/ Btu for SRC-Water Slurry. On a lb/10/sup 6/ Btu basis, emissions from SRC Residual Oil averaged 79 and 78%, respectively, lower than the SRC Fuel and SRC-Water Slurry. The lower SRC Residual Oil emissions were due, in part, to the lower ash content of the oil and more efficient combustion. The SRC Fuel had the highest emission rate, but only 2% higher than the SRC-Water Slurry. Each fuel type was tested under variable boiler operating parameters to determine its effect on boiler emissions. The program successfully demonstrated that the SRC fuels could be burned in fuel oil boilers modified to handle SRC fuels. This report details the particulate emission program and results from testing conducted at the boiler outlet located before the mobile precipitator take-off duct. The sampling method was EPA Method 17, which uses an in-stack filter.

Not Available

1983-09-01T23:59:59.000Z

242

Oxidation Resistant Graphite Studies  

SciTech Connect (OSTI)

The Very High Temperature Reactor (VHTR) Graphite Research and Development Program is investigating doped nuclear graphite grades exhibiting oxidation resistance. During a oxygen ingress accident the oxidation rates of the high temperature graphite core region would be extremely high resulting in significant structural damage to the core. Reducing the oxidation rate of the graphite core material would reduce the structural effects and keep the core integrity intact during any air-ingress accident. Oxidation testing of graphite doped with oxidation resistant material is being conducted to determine the extent of oxidation rate reduction. Nuclear grade graphite doped with varying levels of Boron-Carbide (B4C) was oxidized in air at nominal 740°C at 10/90% (air/He) and 100% air. The oxidation rates of the boronated and unboronated graphite grade were compared. With increasing boron-carbide content (up to 6 vol%) the oxidation rate was observed to have a 20 fold reduction from unboronated graphite. Visual inspection and uniformity of oxidation across the surface of the specimens were conducted. Future work to determine the remaining mechanical strength as well as graphite grades with SiC doped material are discussed.

W. Windes; R. Smith

2014-07-01T23:59:59.000Z

243

EIA - Greenhouse Gas Emissions Overview  

Gasoline and Diesel Fuel Update (EIA)

Environment Environment Emissions of Greenhouse Gases in the U. S. Release Date: March 31, 2011 | Next Release Date: Report Discontinued | Report Number: DOE/EIA-0573(2009) Greenhouse Gas Emissions Overview Diagram Notes [a] CO2 emissions related to petroleum consumption (includes 64 MMTCO2 of non-fuel-related emissions). [b] CO2 emissions related to coal consumption (includes 0.3 MMTCO2 of non-fuel-related emissions). [c] CO2 emissions related to natural gas consumption (includes 13 MMTCO2 of non-fuel-related emissions). [d] Excludes carbon sequestered in nonfuel fossil products. [e] CO2 emissions from the plastics portion of municipal solid waste (11 MMTCO2) combusted for electricity generation and very small amounts (0.4 MMTCO2) of geothermal-related emissions.

244

GHG emissions | OpenEI  

Open Energy Info (EERE)

GHG emissions GHG emissions Dataset Summary Description These datasets include GHG and CO2 emissions statistics for the European Union (EU). The statistics are available from the European Commission. Source European Commission Date Released Unknown Date Updated Unknown Keywords Biofuels CO2 emissions EU GHG emissions Data application/vnd.ms-excel icon Total GHG and CO2 Emissions for EU (xls, 853.5 KiB) application/vnd.ms-excel icon GHG Emissions by Sector, all member countries (xls, 2 MiB) application/vnd.ms-excel icon GHG Emissions from Transport, all member countries (xls, 1.3 MiB) application/vnd.ms-excel icon CO2 emissions by sector, all member countries (xls, 2.1 MiB) application/vnd.ms-excel icon CO2 emissions by transport, all member countries (xls, 1.5 MiB)

245

Air Pollution Control Regulations: No.27 - Control of Nitrogen Oxide  

Broader source: Energy.gov (indexed) [DOE]

Air Pollution Control Regulations: No.27 - Control of Nitrogen Air Pollution Control Regulations: No.27 - Control of Nitrogen Oxide Emissions (Rhode Island) Air Pollution Control Regulations: No.27 - Control of Nitrogen Oxide Emissions (Rhode Island) < Back Eligibility Commercial Industrial Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Rhode Island Program Type Environmental Regulations Provider Department of Environmental Management These regulations apply to stationary sources with the potential to emit 50 tons of nitrogen oxides (NOx) per year from all pollutant-emitting equipment or activities. The regulations describe possibilities for exemptions (i.e., for sources which have the potential to emit 50 tons but do not actually reach that level) and Reasonably Available Control

246

METAL OXIDE NANOPARTICLES  

SciTech Connect (OSTI)

This chapter covers the fundamental science, synthesis, characterization, physicochemical properties and applications of oxide nanomaterials. Explains fundamental aspects that determine the growth and behavior of these systems, briefly examines synthetic procedures using bottom-up and top-down fabrication technologies, discusses the sophisticated experimental techniques and state of the art theory results used to characterize the physico-chemical properties of oxide solids and describe the current knowledge concerning key oxide materials with important technological applications.

FERNANDEZ-GARCIA,M.; RODGRIGUEZ, J.A.

2007-10-01T23:59:59.000Z

247

Optimal irreversible stimulated emission  

E-Print Network [OSTI]

We studied the dynamics of an initially inverted atom in a semi-infinite waveguide, in the presence of a single propagating photon. We show that atomic relaxation is enhanced by a factor of 2, leading to maximal bunching in the output field. This optimal irreversible stimulated emission is a novel phenomenon that can be observed with state-of-the-art solid-state atoms and waveguides. When the atom interacts with two one-dimensional electromagnetic environments, the preferential emission in the stimulated field can be exploited to efficiently amplify a classical or a quantum state.

D Valente; Y Li; J P Poizat; J M Gerard; L C Kwek; M F Santos; A Auffeves

2012-08-28T23:59:59.000Z

248

Controlled spontaneous emission  

E-Print Network [OSTI]

The problem of spontaneous emission is studied by a direct computer simulation of the dynamics of a combined system: atom + radiation field. The parameters of the discrete finite model, including up to 20k field oscillators, have been optimized by a comparison with the exact solution for the case when the oscillators have equidistant frequencies and equal coupling constants. Simulation of the effect of multi-pulse sequence of phase kicks and emission by a pair of atoms shows that both the frequency and the linewidth of the emitted spectrum could be controlled.

Jae-Seung Lee; Mary A. Rohrdanz; A. K. Khitrin

2007-07-03T23:59:59.000Z

249

Photocatalytic destruction of automobile exhaust emissions  

SciTech Connect (OSTI)

Hydrocarbons, carbon monoxide, and nitrogen oxides contained in automobile exhaust emissions are among the major atmospheric air pollutants. During the first few minutes of a cold start of the engine, the emission levels of unburned hydrocarbon and CO pollutants are very high due to the inefficiency of the cold engine and the poor activity of the catalysts lower temperatures. Therefore, it is necessary to provide an alternative approach to deal with this specific problem in order to meet near-term regulatory requirements. Our approach has been to use known photocatalytic reactions obtainable on semiconducting powders such as titanium dioxide. In this presentation we describe our recent studies aimed at the photocatalytic reduction of unburned hydrocarbons and carbon monoxide in automobile exhaust emissions. Our results demonstrate the effective destruction of propylene into water and carbon dioxide. The conversion was found to be dependent on the propylene flow rate. The reaction rate was studied as a function of time, humidity and temperature. The effect of the power of the UV source on conversion will also be presented.

Kaviranta, P.D.; Peden, C.H.F. [Pacific Northwest National Lab., Richland, WA (United States)

1996-10-01T23:59:59.000Z

250

EIA - Greenhouse Gas Emissions Overview  

Gasoline and Diesel Fuel Update (EIA)

Greenhouse Gas Tables (1990-2009) Greenhouse Gas Tables (1990-2009) Table Title Formats Overview 1 U.S. emissions of greenhouse gases, based on global warming potential 2 U.S. greenhouse gas intensity and related factors 3 Distribution of total U.S. greenhouse gas emissions by end-use sector 4 World energy-related carbon dioxide emissions by region 5 Greenhouse gases and 100-year net global warming potentials Carbon dioxide emissions 6 U.S. carbon dioxide emissions from energy and industry 7 U.S. energy-related carbon dioxide emissions by end-use sector 8 U.S. carbon dioxide emission from residential sector energy consumption 9 U.S. carbon dioxide emissions from commercial sector energy consumption 10 U.S. carbon dioxide emissions from industrial sector energy consumption

251

NETL: Mercury Emissions Control Technologies - Bench Scale Kinetics of  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Bench Scale Kinetics of Mercury Reactions in FGD Liquors Bench Scale Kinetics of Mercury Reactions in FGD Liquors When research into the measurement and control of Hg emissions from coal-fired power plants began in earnest in the early 1990s, it was observed that oxidized mercury can be scrubbed at high efficiency in wet FGD systems, while elemental mercury can not. In many cases, elemental mercury concentrations were observed to increase slightly across wet FGD systems, but this was typically regarded as within the variability of the measurement methods. However, later measurements have shown substantial re-emissions from some FGD systems. The goal of this project is to develop a fundamental understanding of the aqueous chemistry of mercury (Hg) absorbed by wet flue gas desulfurization (FGD) scrubbing liquors. Specifically, the project will determine the chemical reactions that oxidized mercury undergoes once absorbed, the byproducts of those reactions, and reaction kinetics.

252

Secondary emission gas chamber  

E-Print Network [OSTI]

For a hadron calorimeter active element there is considered a gaseous secondary emis-sion detector (150 micron gap, 50 kV/cm). Such one-stage parallel plate chamber must be a radiation hard, fast and simple. A model of such detector has been produced, tested and some characteristics are presented.

V. In'shakov; V. Kryshkin; V. Skvortsov

2014-12-10T23:59:59.000Z

253

CARBON DIOXIDE EMISSION REDUCTION  

E-Print Network [OSTI]

.5 Primary Energy Use and Carbon Dioxide Emissions for Selected US Chemical Subsectors in 1994 ...............................................................................................................16 Table 2.7 1999 Energy Consumption and Specific Energy Consumption (SEC) in the U.S. Cement Efficiency Technologies and Measures in Cement Industry.................22 Table 2.9 Energy Consumption

Delaware, University of

254

Graphene Coating Coupled Emission  

E-Print Network [OSTI]

Graphene Coating Coupled Emission A COMSET, A single sheet of sp2-hybridized carbon atoms, called of graphene and its unique properties, I will present amplification of surface graphene-Ag hybrid films which when graphene is used as the spacer layer in a conventional Ag- harnessed the nonlinear properties

Shyamasundar, R.K.

255

Ethylene Oxide Explosions  

Science Journals Connector (OSTI)

... THE occasional occurrence of ethylene oxide explosions during the fumigation of dried fruit has led us to undertake a detailed ... yielded results somewhat like those for acetaldehyde1,2.. Cool flames can be initiated in ethylene oxide – air mixtures in the neighbourhood of 330° C. at atmospheric pressure. ...

J. H. BURGOYNE; F. A. BURDEN

1948-07-31T23:59:59.000Z

256

Oxidative Degradation of Monoethanolamine  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Oxidative Degradation of Monoethanolamine Oxidative Degradation of Monoethanolamine Susan Chi Gary T. Rochelle* (gtr@che.utexas.edu, 512-471-7230) The University of Texas at Austin Department of Chemical Engineering Austin, Texas 78712 Prepared for presentation at the First National Conference on Carbon Sequestration, Washington, DC, May 14-17, 2001 Abstract Oxidative degradation of monoethanolamine (MEA) was studied under typical absorber condition of 55°C. The rate of evolution of NH 3 , which was indicative of the overall rate of degradation, was measured continuously in a batch system sparged with air. Dissolved iron from 0.0001 mM to 1 mM yields oxidation rates from 0.37 to 2 mM/hr in MEA solutions loaded with 0.4 mole CO 2 / mole MEA. Ethylenediaminetetraacetic acid (EDTA) and N,N-bis(2- hydroxyethyl)glycine effectively decrease the rate of oxidation in the presence of iron by 40 to

257

Regenerative thermal oxidation and alternative technologies for VOC control  

SciTech Connect (OSTI)

Thermal oxidation technologies have been used successfully to control VOC`s for many years but the recent 1990 Clean Air Act Amendments have spurred improvements in the established processes and development of economic alternatives. The combination of the regulatory maze and confusion in the selection of the best technology for a particular application has created a potential nightmare for those companies facing a need to reduce their VOC EMISSIONS. The relative advantages and disadvantages of regenerative, recuperative and catalytic oxidizers will be reviewed, with an emphasis on the economic justification for regenerative thermal oxidation (RTO). Control efficiencies of more than 99% have been demonstrated for RTO`s on a multitude of industrial process exhaust streams. Lowest evaluated cost over a fifteen to twenty year effective equipment life is a key selection criteria. This paper describes the underlying principles of thermal oxidation, and discusses the applicability of these and other emerging technologies for VOC control.

Biedell, E.L. [REECQ, Somerville, NJ (United States)

1995-12-31T23:59:59.000Z

258

Allocation of emission rights Economic incentives for emission  

E-Print Network [OSTI]

for all countries High cost effectiviness:High cost effectiviness: International Emission trading Fairness NAM Department of Physical Resource Theory #12;Financial flows from emissions trading 450 ppmGDP SAS CPA WEU NAM Department of Physical Resource Theory #12;Financial flows from emissions trading 450

259

Downstream Emissions Trading for Transport  

Science Journals Connector (OSTI)

This chapter addresses the issue of downstream emission trading within the transport sector. It is argued that emission trading may be relevant in this sector, and ... regarding international transport, it is arg...

Charles Raux

2011-01-01T23:59:59.000Z

260

Phase-Transfer-Catalyzed Oxidations  

Science Journals Connector (OSTI)

Phase-transfer catalysis (PTC) offers many excellent opportunities for conducting oxidation reactions using inexpensive primary oxidants such as oxygen, sodium hypochlorite, hydrogen peroxide, electrooxidation...

Charles M. Starks; Charles L. Liotta; Marc E. Halpern

1994-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Radionuclide Air Emission Report for 2011  

E-Print Network [OSTI]

470E-20Ì1 Radionuclide Air Emission Report for Prepared by:Environmental Protection Agency, National Emission Standardsfor Emissions of Radionuclides Other Than Radon From

Wahl, Linnea

2012-01-01T23:59:59.000Z

262

GBTL Workshop GHG Emissions | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

GHG Emissions GBTL Workshop GHG Emissions EERE Presentation of Greenhouse Gas EmissionsResource Potential gbtlworkshopghgemissions.pdf More Documents & Publications GBTL...

263

Distributed Energy Resources for Carbon Emissions Mitigation  

E-Print Network [OSTI]

Energy Resources for Carbon Emissions Mitigation RyanEnergy Resources for Carbon Emissions Mitigation Ryanand/or site-attributable carbon emissions at commercial and

Firestone, Ryan; Marnay, Chris

2008-01-01T23:59:59.000Z

264

Low emissions diesel fuel  

DOE Patents [OSTI]

A method and matter of composition for controlling NO.sub.x emissions from existing diesel engines. The method is achieved by adding a small amount of material to the diesel fuel to decrease the amount of NO.sub.x produced during combustion. Specifically, small amounts, less than about 1%, of urea or a triazine compound (methylol melamines) are added to diesel fuel. Because urea and triazine compounds are generally insoluble in diesel fuel, microemulsion technology is used to suspend or dissolve the urea or triazine compound in the diesel fuel. A typical fuel formulation includes 5% t-butyl alcohol, 4.5% water, 0.5% urea or triazine compound, 9% oleic acid, and 1% ethanolamine. The subject invention provides improved emissions in heavy diesel engines without the need for major modifications.

Compere, Alicia L. (Knoxville, TN); Griffith, William L. (Oak Ridge, TN); Dorsey, George F. (Farragut, TN); West, Brian H. (Kingston, TN)

1998-01-01T23:59:59.000Z

265

Regenerative catalytic oxidation  

SciTech Connect (OSTI)

Currently Regenerative Thermal Oxidizers (R.T.O.`s) are an accepted technology for the control of volatile organic compounds (VOC`s) and hazardous air pollutants (HAP`s). This control technology, when introduced, offered substantial reductions in operating costs, especially auxiliary fuel requirements when compared to existing control technologies such as recuperative thermal and recuperative catalytic oxidizers. While these savings still exist, there is a demand for control of new and/or hybrid technologies, one of which is Regenerative Catalytic Oxidizers (R.C.O.`s). This paper will explore the development of regenerative catalytic oxidation from the theoretical stage through pilot testing through a commercial installation. The operating cost of R.C.O.`s will be compared to R.T.O.`s to verify the savings that are achievable through the use of regenerative catalytic oxidation. In the development of this technology, which is a combination of two (2) existing technologies, R.T.O.`s and catalysis, a second hybrid technology was explored and pilot tested. This is a combination R.C.O. for VOC and HAP control and simultaneous SCR (Selective Catalytic Reduction) for NOx (Oxides of Nitrogen) control. Based on the pilot and full scale testing, both regenerative catalytic oxidizers and systems which combine R.C.O. with SCR for both VOC and NOx reduction are economically viable and are in fact commercially available. 6 figs., 2 tabs.

Gribbon, S.T. [Engelhard Process Emission Systems, South Lyon, MI (United States)

1996-12-31T23:59:59.000Z

266

CORONAL EMISSION LINES AS THERMOMETERS  

SciTech Connect (OSTI)

Coronal emission-line intensities are commonly used to measure electron temperatures using emission measure and/or line ratio methods. In the presence of systematic errors in atomic excitation calculations and data noise, the information on underlying temperature distributions is fundamentally limited. Increasing the number of emission lines used does not necessarily improve the ability to discriminate between different kinds of temperature distributions.

Judge, Philip G., E-mail: judge@ucar.ed [High Altitude Observatory, National Center for Atmospheric Research , P.O. Box 3000, Boulder CO 80307-3000 (United States)

2010-01-10T23:59:59.000Z

267

Coronal emission lines as thermometers  

E-Print Network [OSTI]

Coronal emission line intensities are commonly used to measure electron temperatures using emission measure and/or line ratio methods. In the presence of systematic errors in atomic excitation calculations and data noise, the information on underlying temperature distributions is fundamentally limited. Increasing the number of emission lines used does not necessarily improve the ability to discriminate between different kinds of temperature distributions.

Judge, Philip G

2009-01-01T23:59:59.000Z

268

On-Road Measurement of Gas and Particle Phase Pollutant Emission Factors  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

On-Road Measurement of Gas and Particle Phase Pollutant Emission Factors On-Road Measurement of Gas and Particle Phase Pollutant Emission Factors for Individual Heavy-Duty Diesel Trucks Title On-Road Measurement of Gas and Particle Phase Pollutant Emission Factors for Individual Heavy-Duty Diesel Trucks Publication Type Journal Article Year of Publication 2012 Authors Dallmann, Timothy R., Steven J. DeMartini, Thomas W. Kirchstetter, Scott C. Herndon, Timothy B. Onasch, Ezra C. Wood, and Robert A. Harley Journal Environmental Science and Technology Volume 46 Issue 15 Pagination 8511-8518 Abstract Pollutant concentrations in the exhaust plumes of individual diesel trucks were measured at high time resolution in a highway tunnel in Oakland, CA, during July 2010. Emission factors for individual trucks were calculated using a carbon balance method, in which pollutants measured in each exhaust plume were normalized to measured concentrations of carbon dioxide. Pollutants considered here include nitric oxide, nitrogen dioxide (NO2), carbon monoxide, formaldehyde, ethene, and black carbon (BC), as well as optical properties of emitted particles. Fleet-average emission factors for oxides of nitrogen (NOx) and BC respectively decreased 30 ± 6 and 37 ± 10% relative to levels measured at the same location in 2006, whereas a 34 ± 18% increase in the average NO2 emission factor was observed. Emissions distributions for all species were skewed with a small fraction of trucks contributing disproportionately to total emissions. For example, the dirtiest 10% of trucks emitted half of total NO2 and BC emissions. Emission rates for NO2 were found to be anticorrelated with all other species considered here, likely due to the use of catalyzed diesel particle filters to help control exhaust emissions. Absorption and scattering cross-section emission factors were used to calculate the aerosol single scattering albedo (SSA, at 532 nm) for individual truck exhaust plumes, which averaged 0.14 ± 0.03.

269

EIA - Emissions of Greenhouse Gases in the United States 2009  

Gasoline and Diesel Fuel Update (EIA)

Environment Environment Emissions of Greenhouse Gases in the U. S. Release Date: March 31, 2011 | Next Release Date: Report Discontinued | Report Number: DOE/EIA-0573(2009) This report-the eighteenth annual report-presents the U.S. Energy Information Administration's latest estimates of emissions for carbon dioxide, methane, nitrous oxide, and other greenhouse gases. Download the GHG Report Introduction For this report, activity data on coal and natural gas consumption and electricity sales and losses by sector were obtained from the January 2011 Monthly Energy Review (MER). In keeping with current international practice, this report presents data on greenhouse gas emissions in million metric tons carbon dioxide equivalent. The data can be converted to carbon equivalent units by

270

Analysis of Emission Shapes  

E-Print Network [OSTI]

Shapes of relative emission sources can be accessed by expanding shapes of correlations at low relative velocities in pair center of mass in Cartesian harmonics. Coefficients of expansion for correlations are related to the respective coefficients of expansion for the sources through one dimensional integral transforms involving properties of pair relative wavefunctions. The methodology is illustrated with analyses of NA49 and PHENIX correlation data.

P. Danielewicz

2007-07-03T23:59:59.000Z

271

Analysis of Emission Shapes  

E-Print Network [OSTI]

Shapes of relative emission sources can be accessed by expanding shapes of correlations at low relative velocities in pair center of mass in Cartesian harmonics. Coefficients of expansion for correlations are related to the respective coefficients of expansion for the sources through one dimensional integral transforms involving properties of pair relative wavefunctions. The methodology is illustrated with analyses of NA49 and PHENIX correlation data.

Danielewicz, P

2007-01-01T23:59:59.000Z

272

Fundamental studies of stress distributions and stress relaxation in oxide scales on high temperature alloys. [Final progress report  

SciTech Connect (OSTI)

This report summarizes a three-year study of stresses arising in the oxide scale and underlying metal during high temperature oxidation and of scale cracking. In-situ XRD was developed to measure strains during oxidation over 1000{degrees}C on pure metals. Acoustic emission was used to observe scale fracture during isothermal oxidation and cooling, and statistical analysis was used to infer mechanical aspects of cracking. A microscratch technique was used to measure the fracture toughness of scale/metal interface. A theoretical model was evaluated for the development and relaxation of stresses in scale and metal substrate during oxidation.

Shores, D.A.; Stout, J.H.; Gerberich, W.W.

1993-06-01T23:59:59.000Z

273

Induced and Spontaneous Emission  

Science Journals Connector (OSTI)

The problem of induced and spontaneous emission is investigated for an atomic two?level system with incident beams of radiation which are either in a coherent state or in a stationary state (contain a definite number of photons). The treatment is fully quantum?mechanical and is confined to the case where the frequency spectrum of the incident beam is narrow compared to the natural linewidth of the system. It is shown that under such conditions the spontaneous emission for frequencies within the narrow band of the incident radiation is sharply reduced compared to the prediction of the natural lineshape. It is shown that a hole is burned in the natural lineshape within the narrow frequency band thus effectively quenching the spontaneous emission at some frequency within the band. This effect is shown to occur both for the coherent and stationary beams. Quantities proportional to the induced and spontaneous probability amplitudes and the lifetimes are computed for times comparable to and long compared to the free lifetime of the state. An expression is found for the spectrum of the emergent radiation in terms of these quantities. Its physical meaning is briefly discussed. The density operator of the field for all times is given.

Saul M. Bergmann

1967-01-01T23:59:59.000Z

274

Emissions Inventory Report Summary for Los Alamos National Laboratory for Calendar Year 2004  

SciTech Connect (OSTI)

Los Alamos National Laboratory (LANL) is subject to annual emissions reporting requirements for regulated air pollutants under Title 20 of the New Mexico Administrative Code, Chapter 2, Part 73 (20.2.73 NMAC), ''Notice of Intent and Emissions Inventory Requirements''. The applicability of the requirements is based on the Laboratory's potential to emit 100 tons per year of suspended particulate matter, nitrogen oxides, carbon monoxide, sulfur oxides, or volatile organic compounds. Additionally, on April 30, 2004, LANL was issued a Title V Operating Permit from the New Mexico Environment Department, Air Quality Bureau, under 20.2.70 NMAC. This Title V Operating Permit (Permit No. P-100) includes emission limits and operating limits for all regulated sources of air pollution at LANL. The Title V Operating Permit also requires semi-annual emissions reporting for all sources included in the permit. This report summarizes both the annual emissions inventory reporting and the semi-annual emissions reporting for LANL for calendar year 2004. LANL's 2004 emissions are well below the emission limits in the Title V Operating Permit.

M. Stockton

2005-10-01T23:59:59.000Z

275

Apparatus for photocatalytic destruction of internal combustion engine emissions during cold start  

SciTech Connect (OSTI)

A method and apparatus are disclosed for the destruction of emissions from an internal combustion engine wherein a substrate coated with TiO{sub 2} is exposed to a light source in the exhaust system of an internal combustion engine thereby catalyzing oxidation/reduction reactions between gaseous hydrocarbons, carbon monoxide, nitrogen oxides and oxygen in the exhaust of the internal combustion engine. 4 figs.

Janata, J.; McVay, G.L.; Peden, C.H.; Exarhos, G.J.

1998-07-14T23:59:59.000Z

276

Process for combined control of mercury and nitric oxide.  

SciTech Connect (OSTI)

Continuing concern about the effects of mercury in the environment may lead to requirements for the control of mercury emissions from coal-fired power plants. If such controls are mandated, the use of existing flue-gas cleanup systems, such as wet scrubbers currently employed for flue-gas desulfurization, would be desirable, Such scrubbers have been shown to be effective for capturing oxidized forms of mercury, but cannot capture the very insoluble elemental mercury (Hg{sup 0}) that can form a significant fraction of the total emissions. At Argonne National Laboratory, we have proposed and tested a concept for enhancing removal of Hg{sup 0}, as well as nitric oxide, through introduction of an oxidizing agent into the flue gas upstream of a scrubber, which readily absorbs the soluble reaction products. Recently, we developed a new method for introducing the oxidizing agent into the flue-gas stream that dramatically improved reactant utilization. The oxidizing agent employed was NOXSORB{trademark}, which is a commercial product containing chloric acid and sodium chlorate. When a dilute solution of this agent was introduced into a gas stream containing Hg{sup 0} and other typical flue-gas species at 300 F, we found that about 100% of the mercury was removed from the gas phase and recovered in process liquids. At the same time, approximately 80% of the nitric oxide was removed. The effect of sulfur dioxide on this process was also investigated and the results showed that it slightly decreased the amount of Hg{sup 0} oxidized while appearing to increase the removal of nitric oxide from the gas phase. We are currently testing the effects of variations in NOXSORB{trademark} concentration, sulfur dioxide concentration, nitric oxide concentration, and reaction time (residence time). Preliminary economic projections based on the results to date indicate that the chemical cost for nitric oxide oxidation could be less than $5,000/ton removed, while for Hg{sup 0} oxidation it would be about $20,000/lb removed.

Livengood, C. D.; Mendelsohn, M. H.

1999-11-03T23:59:59.000Z

277

Choose the best heat-recovery method for thermal oxidizers  

SciTech Connect (OSTI)

Thermal oxidation is current the most economically favorable add-on method of controlling hydrocarbon air emissions of moderate to low concentration (below 10,000 ppm). This concentration range covers emissions from a wide variety of chemical process industries (CPI) sources, including dryers, reactor vents, tank vents, and coaters. Thermal oxidizer systems consist of three basic sub-systems--burner, combustion chamber, and primary heat recovery. Selecting the type of primary heat recovery is probably the most important decision in the design of a thermal oxidizer, and requires consideration of a wide range of factors. The two most widely used types of primary heat recovery--recuperative and regenerative--each have distinct advantages and disadvantages. In general, recuperative oxidizers are simpler and less costly to purchase, whereas regenerative oxidizers offer substantially lower operating costs. Selecting between recuperative and regenerative heat recovery requires balancing a number of factors, such as capital and operating costs, exhaust gas composition and temperature, and secondary heat demand. This article provides guidance on when, where, and how to use each.

Klobucar, J.M.

1995-04-01T23:59:59.000Z

278

SOLID OXIDE PLANAR AND TUBULAR SOLID OXIDE FUEL  

E-Print Network [OSTI]

SOLID OXIDE PLANAR AND TUBULAR SOLID OXIDE FUEL CELLS Dynamic Simulation Approach Modular Approach · Parallel planes: PSOFC · Other: combustor, reformer Solid Oxide Fuel Cell Electrochemistry Cell Reactions · Slow pressure transients #12;Fuel Cell Assumptions · H2 electrochemically oxidized only · CO consumed

Mease, Kenneth D.

279

Syngas Oxidation Mechanism  

Science Journals Connector (OSTI)

A comprehensive analysis of synthesis gas (syngas) oxidation kinetics in wide ranges of temperature ... on the basis of the reaction mechanism of syngas ignition and combustion in air. A vast set of experimental ...

A. M. Starik; N. S. Titova; A. S. Sharipov…

2010-09-01T23:59:59.000Z

280

Implementation of SB 1368 Emission Performance  

E-Print Network [OSTI]

........................................................................................................ 18 Calculation of Biomass, Biogas or Landfill Net Emissions ..................................... 19

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Partnerships to continue moving toward zero emissions  

E-Print Network [OSTI]

Partnerships to continue moving toward zero emissions Zero Emission transportation goals Zero Emission MAP makes available technical assistance to states and cities to support the growth of zero emission mobility markets. 1 Research shows

California at Davis, University of

282

Controlled CO preferential oxidation  

DOE Patents [OSTI]

Method is described for controlling the supply of air to a PROX (PReferential OXidation for CO cleanup) reactor for the preferential oxidation in the presence of hydrogen wherein the concentration of the hydrogen entering and exiting the PROX reactor is monitored, the difference there between correlated to the amount of air needed to minimize such difference, and based thereon the air supply to the PROX reactor adjusted to provide such amount and minimize such difference. 2 figs.

Meltser, M.A.; Hoch, M.M.

1997-06-10T23:59:59.000Z

283

Introduction to Photoelectron Emission Microscopy: Principles...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Introduction to Photoelectron Emission Microscopy: Principles and Applications. Introduction to Photoelectron Emission Microscopy: Principles and Applications. Abstract: In the...

284

Improve emissions monitoring  

SciTech Connect (OSTI)

Marathon`s Texas City refinery was subject to five separate EPA regulations in addition to a state program for monitoring and repairing fugitive leaks. In this case history, the refinery sought an organizational solution that reduced monitoring costs and kept the facility fully compliant with current state and federal regulations. Equally important, the new monitoring program incorporated flexibility for future emission-reduction requirements. The paper describes the solution, regulatory background, the previous system, leak-threshold consolidation, operator ownership, and projects benefits.

Vining, S.K. [Marathon Oil Co., Texas City, TX (United States)

1998-01-01T23:59:59.000Z

285

Emission control technology  

SciTech Connect (OSTI)

Environmental protection is indispensable for preserving the earth for later generations. Indeed, industrial development has made our life rich; however, it also accelerates environmental pollution. Above all, such global problems as acid rain caused by SOx and NOx emissions and air pollution caused by particulates have become serious in recent years. Countermeasures currently in service or under development for these problems include: upgrading of fuel-burning systems; conversion of energy sources to clean fuels; pretreatment of fuels; and flue gas treatment. This chapter focuses on technologies that treat flue gases including the circumstances of the development of the technologies.

Yamaguchi, Fumihiko

1993-12-31T23:59:59.000Z

286

Positron Emission Tomography (PET)  

DOE R&D Accomplishments [OSTI]

Positron emission tomography (PET) assesses biochemical processes in the living subject, producing images of function rather than form. Using PET, physicians are able to obtain not the anatomical information provided by other medical imaging techniques, but pictures of physiological activity. In metaphoric terms, traditional imaging methods supply a map of the body's roadways, its, anatomy; PET shows the traffic along those paths, its biochemistry. This document discusses the principles of PET, the radiopharmaceuticals in PET, PET research, clinical applications of PET, the cost of PET, training of individuals for PET, the role of the United States Department of Energy in PET, and the futures of PET.

Welch, M. J.

1990-01-00T23:59:59.000Z

287

Modeling of Diesel Oxidation Catalyst  

Science Journals Connector (OSTI)

Modeling of Diesel Oxidation Catalyst ... Optimization of hydrocarbon (HC) oxidation over a diesel oxidation catalyst (DOC) requires consideration of (i) HC gas diffusion into the catalyst layer, (ii) HC gas adsorption and desorption from catalyst sites, and (iii) kinetics of the oxidation reaction. ... Mutagenicity of Diesel Engine Exhaust Is Eliminated in the Gas Phase by an Oxidation Catalyst but Only Slightly Reduced in the Particle Phase ...

Yasushi Tanaka; Takashi Hihara; Makoto Nagata; Naoto Azuma; Akifumi Ueno

2005-09-30T23:59:59.000Z

288

EIA - Greenhouse Gas Emissions Overview  

Gasoline and Diesel Fuel Update (EIA)

1. Greenhouse Gas Emissions Overview 1. Greenhouse Gas Emissions Overview 1.1 Total emissions Total U.S. anthropogenic (human-caused) greenhouse gas emissions in 2009 were 5.8 percent below the 2008 total (Table 1). The decline in total emissions-from 6,983 million metric tons carbon dioxide equivalent (MMTCO2e) in 2008 to 6,576 MMTCO2e in 2009-was the largest since emissions have been tracked over the 1990-2009 time frame. It was largely the result of a 419-MMTCO2e drop in carbon dioxide (CO2) emissions (7.1 percent). There was a small increase of 7 MMTCO2e (0.9 percent) in methane (CH4) emissions, and an increase of 8 MMTCO2e (4.9 percent), based on partial data, in emissions of man-made gases with high global warming potentials (high-GWP gases). (Draft estimates for emissions of HFC and PFC

289

NETL: Mercury Emissions Control Technologies - Testing of Mercury Control  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Testing of Mercury Control with Calcium-Based Sorbents and Oxidizing Agents Testing of Mercury Control with Calcium-Based Sorbents and Oxidizing Agents Southern Research Institute, Birmingham, Alabama Subcontractor- ARCADIS Geraghty & Miller The overall goal of this project is to test the effectiveness of calcium-based sorbents and oxidizing agents for controlling mercury emissions from coal-fired power plant boilers. ARCADIS Geraghty & Miller, with EPA support, has developed calcium-based sorbents to remove SO2 and mercury simultaneously. The sorbents consist of hydrated lime (Ca(OH)2) and an added oxidant and a silica-modified calcium (CaSiO3) with an added oxidant. The mercury capacity in ug Hg/g sorbent for the two sorbents is 20 and 110-150, respectively, verses a mercury capacity for the current standard sorbent, activated carbon, of 70-100. The advantages of a lime based sorbent verses carbon is lower cost, simultaneous removal of sulfur, and allowance of ash to be utilized for a cement additive.

290

Emissions and fuel economy of a prechamber diesel engine with natural gas dual fuelling  

SciTech Connect (OSTI)

A four-cylinder turbocharged prechamber diesel engine (Caterpillar 3304) was operated with natural gas and pilot diesel fuel ignition over a wide range of load and speed. Measurements were made of fuel consumption and the emissions of unburned hydrocarbons, carbon monoxide, and the oxides of nitrogen. Improvements in fuel economy and emissions were found to be affected by the diesel fuel-gas fraction, and by air restriction and fuel injection timing. Boundaries of unstable, inefficient and knocking operation were defined and the importance of gas-air equivalance ratio was demonstrated in its effect on economy, emissions and stability of operation.

Ding, X.; Hill, P.G.

1986-01-01T23:59:59.000Z

291

Vehicle-emission characteristics using mechanically emulsified alcohol/diesel fuels  

SciTech Connect (OSTI)

A light-duty diesel vehicle fueled with an emulsified alcohol/diesel fuel was operated under cyclic mode. Emission and fuel economy measurements were taken during vehicle operation. The test results showed the volumetric fuel economy decreased slightly. Carbon monoxide emissions increased slightly, and oxides of nitrogen showed no significant change. Particulate emissions were reduced slightly, and the particulate extractables increased slightly. The environmental effect of these data cancel each other resulting in no significant changes in the total release of biological activity into the environment.

Allsup, J.R.; Seizinger, D.E.; Cox, F.W.; Brook, A.L.; McClellan, R.O.

1983-07-01T23:59:59.000Z

292

Effect of biodiesel fuels on diesel engine emissions  

Science Journals Connector (OSTI)

The call for the use of biofuels which is being made by most governments following international energy policies is presently finding some resistance from car and components manufacturing companies, private users and local administrations. This opposition makes it more difficult to reach the targets of increased shares of use of biofuels in internal combustion engines. One of the reasons for this resistance is a certain lack of knowledge about the effect of biofuels on engine emissions. This paper collects and analyzes the body of work written mainly in scientific journals about diesel engine emissions when using biodiesel fuels as opposed to conventional diesel fuels. Since the basis for comparison is to maintain engine performance, the first section is dedicated to the effect of biodiesel fuel on engine power, fuel consumption and thermal efficiency. The highest consensus lies in an increase in fuel consumption in approximate proportion to the loss of heating value. In the subsequent sections, the engine emissions from biodiesel and diesel fuels are compared, paying special attention to the most concerning emissions: nitric oxides and particulate matter, the latter not only in mass and composition but also in size distributions. In this case the highest consensus was found in the sharp reduction in particulate emissions.

Magín Lapuerta; Octavio Armas; José Rodríguez-Fernández

2008-01-01T23:59:59.000Z

293

Greenhouse gas emissions from home composting of organic household waste  

SciTech Connect (OSTI)

The emission of greenhouse gases (GHGs) is a potential environmental disadvantage of home composting. Because of a lack of reliable GHG emission data, a comprehensive experimental home composting system was set up. The system consisted of six composting units, and a static flux chamber method was used to measure and quantify the GHG emissions for one year composting of organic household waste (OHW). The average OHW input in the six composting units was 2.6-3.5 kg week{sup -1} and the temperature inside the composting units was in all cases only a few degrees (2-10 {sup o}C) higher than the ambient temperature. The emissions of methane (CH{sub 4}) and nitrous oxide (N{sub 2}O) were quantified as 0.4-4.2 kg CH{sub 4} Mg{sup -1} input wet waste (ww) and 0.30-0.55 kg N{sub 2}O Mg{sup -1} ww, depending on the mixing frequency. This corresponds to emission factors (EFs) (including only CH{sub 4} and N{sub 2}O emissions) of 100-239 kg CO{sub 2}-eq. Mg{sup -1} ww. Composting units exposed to weekly mixing had the highest EFs, whereas the units with no mixing during the entire year had the lowest emissions. In addition to the higher emission from the frequently mixed units, there was also an instant release of CH{sub 4} during mixing which was estimated to 8-12% of the total CH{sub 4} emissions. Experiments with higher loads of OHW (up to 20 kg every fortnight) entailed a higher emission and significantly increased overall EFs (in kg substance per Mg{sup -1} ww). However, the temperature development did not change significantly. The GHG emissions (in kg CO{sub 2}-eq. Mg{sup -1} ww) from home composting of OHW were found to be in the same order of magnitude as for centralised composting plants.

Andersen, J.K., E-mail: jka@env.dtu.d [Department of Environmental Engineering, Technical University of Denmark, DK-2800, Kongens Lyngby (Denmark); Boldrin, A.; Christensen, T.H.; Scheutz, C. [Department of Environmental Engineering, Technical University of Denmark, DK-2800, Kongens Lyngby (Denmark)

2010-12-15T23:59:59.000Z

294

Oxidation of Mercury in Products of Coal Combustion  

SciTech Connect (OSTI)

Laboratory measurements of mercury oxidation during selective catalytic reduction (SCR) of nitric oxide, simulation of pilot-scale measurements of mercury oxidation and adsorption by unburned carbon and fly ash, and synthesis of new materials for simultaneous oxidation and adsorption of mercury, were performed in support of the development of technology for control of mercury emissions from coal-fired boilers and furnaces. Conversion of gas-phase mercury from the elemental state to water-soluble oxidized form (HgCl{sub 2}) enables removal of mercury during wet flue gas desulfurization. The increase in mercury oxidation in a monolithic V{sub 2}O{sub 5}-WO{sub 3}/TiO{sub 2} SCR catalyst with increasing HCl at low levels of HCl (< 10 ppmv) and decrease in mercury oxidation with increasing NH{sub 3}/NO ratio during SCR were consistent with results of previous work by others. The most significant finding of the present work was the inhibition of mercury oxidation in the presence of CO during SCR of NO at low levels of HCl. In the presence of 2 ppmv HCl, expected in combustion products from some Powder River Basin coals, an increase in CO from 0 to 50 ppmv reduced the extent of mercury oxidation from 24 {+-} 3 to 1 {+-} 4%. Further increase in CO to 100 ppmv completely suppressed mercury oxidation. In the presence of 11-12 ppmv HCl, increasing CO from 0 to {approx}120 ppmv reduced mercury oxidation from {approx}70% to 50%. Conversion of SO{sub 2} to sulfate also decreased with increasing NH{sub 3}/NO ratio, but the effects of HCl and CO in flue gas on SO{sub 2} oxidation were unclear. Oxidation and adsorption of mercury by unburned carbon and fly ash enables mercury removal in a particulate control device. A chemical kinetic mechanism consisting of nine homogeneous and heterogeneous reactions for mercury oxidation and removal was developed to interpret pilot-scale measurements of mercury oxidation and adsorption by unburned carbon and fly ash in experiments at pilot scale, burning bituminous coals (Gale, 2006) and blends of bituminous coals with Powder River Basin coal (Gale, 2005). The removal of mercury by fly ash and unburned carbon in the flue gas from combustion of the bituminous coals and blends was reproduced with satisfactory accuracy by the model. The enhancement of mercury capture in the presence of calcium (Gale, 2005) explained a synergistic effect of blending on mercury removal across the baghouse. The extent of mercury oxidation, on the other hand, was not so well described by the simulation, because of oversensitivity of the oxidation process in the model to the concentration of unburned carbon. Combined catalysts and sorbents for oxidation and removal of mercury from flue gas at low temperature were based on surfactant-templated silicas containing a transition metal and an organic functional group. The presence of both metal ions and organic groups within the pore structure of the materials is expected to impart to them the ability to simultaneously oxidize elemental mercury and adsorb the resulting oxidized mercury. Twelve mesoporous organosilicate catalysts/sorbents were synthesized, with and without metals (manganese, titanium, vanadium) and organic functional groups (aminopropyl, chloropropyl, mercaptopropyl). Measurement of mercury oxidation and adsorption by the candidate materials remains for future work.

Peter Walsh; Giang Tong; Neeles Bhopatkar; Thomas Gale; George Blankenship; Conrad Ingram; Selasi Blavo Tesfamariam Mehreteab; Victor Banjoko; Yohannes Ghirmazion; Heng Ban; April Sibley

2009-09-14T23:59:59.000Z

295

Oxidation of alloys targeted for advanced steam turbines  

SciTech Connect (OSTI)

Ultra supercritical (USC) power plants offer the promise of higher efficiencies and lower emissions. Current goals of the U.S. Department of Energy’s Advanced Power Systems Initiatives include coal generation at 60% efficiency, which would require steam temperatures of up to 760°C. This research examines the steamside oxidation of alloys for use in USC systems, with emphasis placed on applications in high- and intermediate-pressure turbines.

Holcomb, G.R.; Covino, B.S., Jr.; Bullard, S.J.; Ziomek-Moroz, M.; Alman, D.E.

2006-03-12T23:59:59.000Z

296

Using market-based dispatching with environmental price signals to reduce emissions and  

Science Journals Connector (OSTI)

The possibility of using electricity dispatching strategies to achieve a 50% nitrogen oxide (NOx) emission reduction from electricity generating units was examined using the grid of the Electricity Reliability Council of Texas as a case study. Simulations of a hypothetical policy demonstrate that imposing higher NOx prices induces a switch from some coal-fired generation to natural gas generation, lowering NOx emissions. The simulation is for a day with relatively high electricity demand and accounts for transmission constraints. In addition to the lowering of the NOx emissions, there are co-benefits of the redispatching of generation from coal to natural gas, including reductions in the emissions of sulfur oxides (24%–71%), Hg (16%–82%) and CO2 (8.8%–22%). Water consumption was also decreased, by 4.4%–8.7%. Substantial reductions of NOx emissions can be achieved for an increased generation cost of 4–13%, which is due to the higher fuel price of gas relative to coal (assuming a price of $3.87 per MMBTU (MMBTU: million British thermal units) for natural gas, and $1.89 per MMBTU for coal). However, once the system has reduced NOx emissions by approximately 50%, there is little incremental reduction in emissions due to further increases in NOx prices.

Nawaf S Alhajeri; Pearl Donohoo; Ashlynn S Stillwell; Carey W King; Mort D Webster; Michael E Webber; David T Allen

2011-01-01T23:59:59.000Z

297

Thin film deposition of barium strontium oxide by rf magnetron sputtering  

SciTech Connect (OSTI)

Barium strontium oxide [(BaSr)O] thin films approximately 1 {mu}m in thickness were deposited on tungsten substrates using rf magnetron sputter deposition for thermionic cathode applications. Three substrate temperatures ranging from 25 to 700 deg. C were used in the deposition processes to create oxide films with different surface morphologies and crystalline structures. The films were characterized with scanning electron microscopy and their surface morphologies were correlated to their thermionic emission properties. The results showed that the surface morphology and crystalline structure of the oxide films strongly affected the emission properties. The oxide film deposited at the lowest substrate temperature of 25 deg. C showed a rough surface and a crystalline structure consisting of nanograins. At higher substrate temperatures, the oxide films exhibited smooth surfaces and close-packed crystalline structures with larger grains. The work function of the oxide films was reduced and the emission current density increased as a result of the increase in the growth temperature. The (BaSr)O film made at 700 deg. C exhibited the lowest work function of 1.57 eV and the largest emission current density of 1.60 A/cm{sup 2} at 1198 K under an electrical field of 0.88 V/{mu}m. The emission current density and the work function of the (BaSr)O thin film cathodes were stable over the testing period of 8 h. Compared to the traditional cathode fabrication process, which involves the coating of carbonates followed by an activation process, rf magnetron sputtering has a greater ability to control the deposition parameters, which makes it a valuable alternative technique to fabricate oxide cathodes.

Liu Yan; Day, Christopher M.; Little, Scott A.; Jin, Feng [Department of Physics and Astronomy, Ball State University, Muncie, Indiana 47306 (United States)

2006-11-15T23:59:59.000Z

298

Fuel Mix and Emissions Disclosure  

Broader source: Energy.gov [DOE]

As part of the state's 1997 electric utility restructuring legislation, Illinois established provisions for the disclosure of fuel mix and emissions data. All electric utilities and alternative...

299

Fuel Mix and Emissions Disclosure  

Broader source: Energy.gov [DOE]

Oregon's 1999 electric utility restructuring legislation requires electricity companies and electric service suppliers to disclose details regarding their fuel mix and emissions of electric...

300

Emissions trading under market imperfections.  

E-Print Network [OSTI]

??In this thesis we consider emissions trading under various market imperfections such as uncertainty over permit price, imperfect competition and noncompliance. First, we study the… (more)

Lappi, Pauli

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

field emission electron microprobe | EMSL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

field emission electron microprobe Leads No leads are available at this time. Magnesium behavior and structural defects in Mg+ ion implanted silicon carbide. Abstract: As a...

302

EMSL - field emission electron microprobe  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

field-emission-electron-microprobe en Magnesium behavior and structural defects in Mg+ ion implanted silicon carbide. http:www.emsl.pnl.govemslwebpublications...

303

Acoustic emission during polymer crystallization  

Science Journals Connector (OSTI)

... .G.; part support to L.K.) Acoustic Emission, Special Technical Publication 505, ASTM, Philadelphia, 1971; Grabec, I. & Peterlin, A. J. Polymer Sci. ...

A. Galeski; L. Koenczoel; E. Piorkowska; E. Baer

1987-01-01T23:59:59.000Z

304

Thermally Oxidized Silicon  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Anneli Munkholm (Lumileds Lighting) and Sean Brennan (SSRL) Anneli Munkholm (Lumileds Lighting) and Sean Brennan (SSRL) Illustration of the silicon positions near the Si-SiO2 interface for a 4° miscut projected onto the ( ) plane. The silicon atoms in the substrate are blue and those in the oxide are red. The small black spots represent the translated silicon positions in the absence of static disorder. The silicon atoms in the oxide have been randomly assigned a magnitude and direction based on the static disorder value at that position in the lattice. The outline of four silicon unit cells is shown in black, whereas the outline of four expanded lattice cells in the oxide is shown in blue One of the most studied devices of modern technology is the field-effect transistor, which is the basis for most integrated circuits. At its heart

305

Oxidative Tritium Decontamination System  

SciTech Connect (OSTI)

The Princeton Plasma Physics Laboratory, Tritium Systems Group has developed and fabricated an Oxidative Tritium Decontamination System (OTDS), which is designed to reduce tritium surface contamination on various components and items. The system is configured to introduce gaseous ozone into a reaction chamber containing tritiated items that require a reduction in tritium surface contamination. Tritium surface contamination (on components and items in the reaction chamber) is removed by chemically reacting elemental tritium to tritium oxide via oxidation, while purging the reaction chamber effluent to a gas holding tank or negative pressure HVAC system. Implementing specific concentrations of ozone along with catalytic parameters, the system is able to significantly reduce surface tritium contamination on an assortment of expendable and non-expendable items. This paper will present the results of various experimentation involving employment of this system.

Charles A. Gentile; John J. Parker; Gregory L. Guttadora; Lloyd P. Ciebiera

2002-02-11T23:59:59.000Z

306

Methanol partial oxidation reformer  

DOE Patents [OSTI]

A partial oxidation reformer comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell.

Ahmed, Shabbir (Bolingbrook, IL); Kumar, Romesh (Naperville, IL); Krumpelt, Michael (Naperville, IL)

1999-01-01T23:59:59.000Z

307

Methanol partial oxidation reformer  

DOE Patents [OSTI]

A partial oxidation reformer comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell.

Ahmed, Shabbir (Bolingbrook, IL); Kumar, Romesh (Naperville, IL); Krumpelt, Michael (Naperville, IL)

2001-01-01T23:59:59.000Z

308

Methanol partial oxidation reformer  

DOE Patents [OSTI]

A partial oxidation reformer is described comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell. 7 figs.

Ahmed, S.; Kumar, R.; Krumpelt, M.

1999-08-17T23:59:59.000Z

309

Methanol partial oxidation reformer  

DOE Patents [OSTI]

A partial oxidation reformer is described comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell. 7 figs.

Ahmed, S.; Kumar, R.; Krumpelt, M.

1999-08-24T23:59:59.000Z

310

Source Emissions and Transport  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

electron micrograph image, Lara Gundel with instrumentation electron micrograph image, Lara Gundel with instrumentation Source Emissions and Transport Investigators conduct research here to characterize and better understand the sources of airborne volatile, semi-volatile and particulate organic pollutants in the indoor environment. This research includes studies of the physical and chemical processes that govern indoor air pollutant concentrations and exposures. The motivation is to contribute to the reduction of potential human health effects. Contacts Randy Maddalena RLMaddalena@lbl.gov (510) 486-4924 Mark Mendell MJMendell@lbl.gov (510) 486-5762 Links Pollutant Sources, Dynamics and Chemistry Group Batteries and Fuel Cells Buildings Energy Efficiency Electricity Grid Energy Analysis Energy Technologies Environmental Impacts

311

Carbon 41 (2003) 18271831 Optical emission spectroscopy study of the influence of  

E-Print Network [OSTI]

arc discharge, laser ablation, and analyzing optical emissions in the plasma and comparing chemical by an iron oxide film with a aligned CNTs [4,5]. thickness of 50 nm by the sol­gel method [8 characterized by scanning electron micro- increased to 80% o

Zhang, Guangyu

312

Analysis of Strategies for Reducing Multiple Emissions from Electric Power Plants: SO2, Nox, CO2  

Reports and Publications (EIA)

This report responds to a request received from Senator David McIntosh on June 29, 2000 to analyze the impacts on energy consumers and producers of coordinated strategies to reduce emissions of sulfur dioxide, nitrogen oxides, and carbon dioxide at U.S. power plants.

2001-01-01T23:59:59.000Z

313

From Acid Dip to Thriving Waters The Impact of Emissions Reductions on Lake Recovery  

E-Print Network [OSTI]

-Range Transboundary Air Pollution for various pollutants including sulphur dioxide (SO2), nitrogen oxides (NOx countries implementing domestic regula- tions to control emissions of pollutants. While the problems October 1, 2007 Abstract We develop an optimal control model for the recovery of a representative

Sadoulet, Elisabeth

314

Tetraalklylammonium polyoxoanionic oxidation catalysts  

DOE Patents [OSTI]

Alkanes are catalytically oxidized in air or oxygen using iron-substituted polyoxoanions (POAs) of the formula: H{sub e{minus}z}[(n-C{sub 4}H{sub 9}){sub 4}N]{sub z}(XM{sub 11}M{prime}O{sub 39}){sup {minus}e}. The M{prime} (e.g., iron(III)/iron(II)) reduction potential of the POAs is affected by selection of the central atom X and the framework metal M, and by the number of tetrabutyl-ammonium groups. Decreased Fe(III)/Fe(II) reduction potential has been found to correlate to increased oxidation activity.

Ellis, P.E.; Lyons, J.E.; Myers, H.K. Jr.; Shaikh, S.N.

1998-10-06T23:59:59.000Z

315

Tetraalykylammonium polyoxoanionic oxidation catalysts  

DOE Patents [OSTI]

Alkanes are catalytically oxidized in air or oxygen using iron-substituted polyoxoanions (POAs) of the formula: H.sub.e-z ›(n-C.sub.4 H.sub.9).sub.4 N!.sub.z (XM.sub.11 M'O.sub.39).sup.-e The M' (e.g., iron(III)/iron(II)) reduction potential of the POAs is affected by selection of the central atom X and the framework metal M, and by the number of tetrabutyl-ammonium groups. Decreased Fe(III)/Fe(II) reduction potential has been found to correlate to increased oxidation activity.

Ellis, Paul E. (Downingtown, PA); Lyons, James E. (Wallingford, PA); Myers, Jr., Harry K. (Cochranville, PA); Shaikh, Shahid N. (Media, PA)

1998-01-01T23:59:59.000Z

316

Emissions of greenhouse gases in the United States, 1987--1994  

SciTech Connect (OSTI)

The Energy Information Administration (EIA) is required by the Energy Policy Act of 1992 to prepare a report on aggregate US national emissions of greenhouse gases for the period 1987--1992, with annual updates thereafter. This is the third annual update report,covering national emissions over the period 1987--1993, with preliminary estimates of US carbon dioxide and halocarbon emissions for 1994. Calculating national aggregate emissions(or ``national inventories``) of greenhouse gases is a recently developed form of intellectual endeavor. Greenhouse gas emissions are rarely measured directly or reported to statistical agencies. Thus, to prepare emissions inventories usually requires inferring emissions indirectly from information collected for other purposes. Both the available information and the inferences drawn may be of varying reliability. Chapter 1 of this report briefly recapitulates some background information about global climate change and the greenhouse effect and discusses important recent developments in global climate change activities. Chapters 2 through 6 cover emissions of carbon dioxide, methane, nitrous oxide, halocarbons, and criteria pollutants, respectively. Chapter 7 describes potential sequestration and emissions of greenhouse gases as a result of land use changes.

NONE

1995-09-25T23:59:59.000Z

317

An oxygenating additive for improving the performance and emission characteristics of marine diesel engines  

Science Journals Connector (OSTI)

Diesel engines provide the major power sources for marine transportation and contribute to the prosperity of the worldwide economy. However, the emissions from diesel engines also seriously threaten the environment and are considered one of the major sources of air pollution. The pollutants emitted from marine vessels are confirmed to cause the ecological environmental problems such as the ozone layer destruction, enhancement of the greenhouse effect, and acid rain, etc. Marine diesel engine emissions such as particulate matter and black smoke carry carcinogen components that significantly impact the health of human beings. Investigations on reducing pollutants, in particular particulate matter and nitrogen oxides are critical to human health, welfare and continued prosperity. The addition of an oxygenating agent into fuel oil is one of the possible approaches for reducing this problem because of the obvious fuel oil constituent influences on engine emission characteristics. Ethylene glycol monoacetate was found to be a promising candidate primarily due to its low poison and oxygen-rich composition properties. In this experimental study ethylene glycol monoacetate was mixed with diesel fuel in various proportions to prepare oxygenated diesel fuel. A four-cylinder diesel engine was used to test the engine performance and emission characteristics. The influences of ethylene glycol monoacetate ration to diesel oil, inlet air temperature and humidity parameters on the engine’s speed and torque were considered. The experimental results show that an increase in the inlet air temperature caused an increase in brake specific fuel consumption (BSFC), carbon monoxide, carbon dioxide emission, and exhaust gas temperature, while decreasing the excess air, oxygen and nitrogen oxide emission concentrations. Increasing the inlet air humidity increased the carbon monoxide concentration while the decreased excess air, oxygen and nitrogen oxide emission concentrations. In addition, increasing ethylene glycol monoacetate ratio in the diesel fuel caused an increase in the BSFC while the excess air and oxygen emission concentrations decreased.

C.-Y. Lin; J.-C. Huang

2003-01-01T23:59:59.000Z

318

A Porphyrin-Stabilized Iridium Oxide Water Oxidation Catalyst  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

A Porphyrin-Stabilized Iridium Oxide Water Oxidation Catalyst Authors: Sherman, B. D., Pillai, S., Kodis, G., Bergkamp, J., Mallouk, T. E., Gust, D., Moore, T. A., and Moore, A. L....

319

X-ray Emission from Massive StarsX-ray Emission from Massive Stars David CohenDavid Cohen  

E-Print Network [OSTI]

X-ray Emission from Massive StarsX-ray Emission from Massive Stars David CohenDavid Cohen/s)Velocity (km/s) #12;absorption emission emission occulted emission emission UV telescope side side front back #12;absorption emission emission occulted emission emission UV telescope side side front back #12;The

Cohen, David

320

EMISSIONS TO AIR OPERATIONAL PROCEDURE  

E-Print Network [OSTI]

EMISSIONS TO AIR OPERATIONAL PROCEDURE Swansea University Estates Services Singleton Park Swansea to Air Department: Estates and Facilities Site: All Author: Ambreen Jahangir Approved by: Mark Durdin PURPOSE: To minimise emissions and discharges to air from boilers, fume cupboards, air conditioning

Harman, Neal.A.

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Oxidative Reforming of Biodiesel Over Molybdenum (IV) Oxide  

E-Print Network [OSTI]

as potential feedstock in solid oxide fuel cells. Petroleum based fuels become scarcer daily, and biodiesel for use in solid oxide fuel cells. This cutting edge area of research continues to be important as energy prove useful for solid oxide fuel cells. METHODS Commercial molybdenum dioxide was used for all tests

Collins, Gary S.

322

Highly oxidized superconductors  

DOE Patents [OSTI]

Novel superconducting materials in the form of compounds, structures or phases are formed by performing otherwise known synthesis in a highly oxidizing atmosphere rather than that created by molecular oxygen at atmospheric pressure or below. This leads to the successful synthesis of novel superconducting compounds which are thermodynamically stable at the conditions under which they are formed. 16 figs.

Morris, D.E.

1994-09-20T23:59:59.000Z

323

Alternative Fuels Data Center: Emissions Reduction Requirements  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

Emissions Reduction Emissions Reduction Requirements to someone by E-mail Share Alternative Fuels Data Center: Emissions Reduction Requirements on Facebook Tweet about Alternative Fuels Data Center: Emissions Reduction Requirements on Twitter Bookmark Alternative Fuels Data Center: Emissions Reduction Requirements on Google Bookmark Alternative Fuels Data Center: Emissions Reduction Requirements on Delicious Rank Alternative Fuels Data Center: Emissions Reduction Requirements on Digg Find More places to share Alternative Fuels Data Center: Emissions Reduction Requirements on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Emissions Reduction Requirements Recognizing the impact of carbon-emitting fuels on climate change and to

324

Update on CO2 emissions  

SciTech Connect (OSTI)

Emissions of CO2 are the main contributor to anthropogenic climate change. Here we present updated information on their present and near-future estimates. We calculate that global CO2 emissions from fossil fuel burning decreased by 1.3% in 2009 owing to the global financial and economic crisis that started in 2008; this is half the decrease anticipated a year ago1. If economic growth proceeds as expected2, emissions are projected to increase by more than 3% in 2010, approaching the high emissions growth rates that were observed from 2000 to 20081, 3, 4. We estimate that recent CO2 emissions from deforestation and other land-use changes (LUCs) have declined compared with the 1990s, primarily because of reduced rates of deforestation in the tropics5 and a smaller contribution owing to forest regrowth elsewhere.

Friedingstein, P. [University of Exeter, Devon, England; Houghton, R.A. [Woods Hole Research Center, Woods Hole, MA; Marland, Gregg [ORNL; Hackler, J. [Woods Hole Research Center, Woods Hole, MA; Boden, Thomas A [ORNL; Conway, T.J. [NOAA, Boulder, CO; Canadell, J.G. [CSIRO Marine and Atmospheric Research; Raupach, Mike [GCP, Canberra, Australia; Ciais, Philippe [Laboratoire des Sciences du Climat et de l'Environement, France; Le Quere, Corrine [University of East Anglia, Norwich, United Kingdom

2010-12-01T23:59:59.000Z

325

Staged membrane oxidation reactor system  

DOE Patents [OSTI]

Ion transport membrane oxidation system comprising (a) two or more membrane oxidation stages, each stage comprising a reactant zone, an oxidant zone, one or more ion transport membranes separating the reactant zone from the oxidant zone, a reactant gas inlet region, a reactant gas outlet region, an oxidant gas inlet region, and an oxidant gas outlet region; (b) an interstage reactant gas flow path disposed between each pair of membrane oxidation stages and adapted to place the reactant gas outlet region of a first stage of the pair in flow communication with the reactant gas inlet region of a second stage of the pair; and (c) one or more reactant interstage feed gas lines, each line being in flow communication with any interstage reactant gas flow path or with the reactant zone of any membrane oxidation stage receiving interstage reactant gas.

Repasky, John Michael; Carolan, Michael Francis; Stein, VanEric Edward; Chen, Christopher Ming-Poh

2012-09-11T23:59:59.000Z

326

Staged membrane oxidation reactor system  

DOE Patents [OSTI]

Ion transport membrane oxidation system comprising (a) two or more membrane oxidation stages, each stage comprising a reactant zone, an oxidant zone, one or more ion transport membranes separating the reactant zone from the oxidant zone, a reactant gas inlet region, a reactant gas outlet region, an oxidant gas inlet region, and an oxidant gas outlet region; (b) an interstage reactant gas flow path disposed between each pair of membrane oxidation stages and adapted to place the reactant gas outlet region of a first stage of the pair in flow communication with the reactant gas inlet region of a second stage of the pair; and (c) one or more reactant interstage feed gas lines, each line being in flow communication with any interstage reactant gas flow path or with the reactant zone of any membrane oxidation stage receiving interstage reactant gas.

Repasky, John Michael; Carolan, Michael Francis; Stein, VanEric Edward; Chen, Christopher Ming-Poh

2014-05-20T23:59:59.000Z

327

Staged membrane oxidation reactor system  

DOE Patents [OSTI]

Ion transport membrane oxidation system comprising (a) two or more membrane oxidation stages, each stage comprising a reactant zone, an oxidant zone, one or more ion transport membranes separating the reactant zone from the oxidant zone, a reactant gas inlet region, a reactant gas outlet region, an oxidant gas inlet region, and an oxidant gas outlet region; (b) an interstage reactant gas flow path disposed between each pair of membrane oxidation stages and adapted to place the reactant gas outlet region of a first stage of the pair in flow communication with the reactant gas inlet region of a second stage of the pair; and (c) one or more reactant interstage feed gas lines, each line being in flow communication with any interstage reactant gas flow path or with the reactant zone of any membrane oxidation stage receiving interstage reactant gas.

Repasky, John Michael; Carolan, Michael Francis; Stein, VanEric Edward; Chen, Christopher Ming-Poh

2013-04-16T23:59:59.000Z

328

Aviation emission inventory development and analysis  

Science Journals Connector (OSTI)

An up to date and accurate aviation emission inventory is a prerequisite for any detailed analysis of aviation emission impact on greenhouse gases and local air quality around airports. In this paper we present an aviation emission inventory using real ... Keywords: Air traffic, Aviation emission, Emission inventory, Environmental modelling

Viet Van Pham; Jiangjun Tang; Sameer Alam; Chris Lokan; Hussein A. Abbass

2010-12-01T23:59:59.000Z

329

Ultrafast Graphene Oxide Humidity Sensors  

Science Journals Connector (OSTI)

Ultrafast Graphene Oxide Humidity Sensors ... Graphene oxide can be exploited in humidity and temperature sensors with a number of convenient features such as flexibility, transparency and suitability for large-scale manufacturing. ... Here we show that the two-dimensional nature of graphene oxide and its superpermeability to water combine to enable humidity sensors with unprecedented response speed (?30 ms response and recovery times). ...

Stefano Borini; Richard White; Di Wei; Michael Astley; Samiul Haque; Elisabetta Spigone; Nadine Harris; Jani Kivioja; Tapani Ryhänen

2013-11-09T23:59:59.000Z

330

Doped palladium containing oxidation catalysts  

DOE Patents [OSTI]

A supported oxidation catalyst includes a support having a metal oxide or metal salt, and mixed metal particles thereon. The mixed metal particles include first particles including a palladium compound, and second particles including a precious metal group (PMG) metal or PMG metal compound, wherein the PMG metal is not palladium. The oxidation catalyst may also be used as a gas sensor.

Mohajeri, Nahid

2014-02-18T23:59:59.000Z

331

Generalized local emission tomography  

DOE Patents [OSTI]

Emission tomography enables locations and values of internal isotope density distributions to be determined from radiation emitted from the whole object. In the method for locating the values of discontinuities, the intensities of radiation emitted from either the whole object or a region of the object containing the discontinuities are inputted to a local tomography function .function..sub..LAMBDA..sup.(.PHI.) to define the location S of the isotope density discontinuity. The asymptotic behavior of .function..sub..LAMBDA..sup.(.PHI.) is determined in a neighborhood of S, and the value for the discontinuity is estimated from the asymptotic behavior of .function..sub..LAMBDA..sup.(.PHI.) knowing pointwise values of the attenuation coefficient within the object. In the method for determining the location of the discontinuity, the intensities of radiation emitted from an object are inputted to a local tomography function .function..sub..LAMBDA..sup.(.PHI.) to define the location S of the density discontinuity and the location .GAMMA. of the attenuation coefficient discontinuity. Pointwise values of the attenuation coefficient within the object need not be known in this case.

Katsevich, Alexander J. (Los Alamos, NM)

1998-01-01T23:59:59.000Z

332

NETL: Mercury Emissions Control Technologies - Evaluation of Mercury  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Control Technology Evaluation of Mercury Emissions from Coal-Fired Facilities w/ SCR and FGD Systems Control Technology Evaluation of Mercury Emissions from Coal-Fired Facilities w/ SCR and FGD Systems CONSOL is evaluating the mercury removal co-benefits achieved by SCR-FGD combi nations. Specific issues that will be addressed include the effects of SCR, catalyst degradation, and load changes on mercury oxidation and capture. This objective will be achieved by measuring mercury removal achieved by SCR-FGD combinations at ten plants with such equipment configurations. These plants include five with wet limestone, three wet lime, and two with dry scrubbing. Material balance will be conducted. Related Papers and Publications: Final Report - April 2006 [PDF-377KB] Topical Report # 11 - January 2006 [PDF-19MB] Topical Report # 9 - January 2006 [PDF-6MB]

333

Control of air pollution emissions from municipal waste combustors  

SciTech Connect (OSTI)

The November 1990 Clear Air Act Amendments (CAAAs) directed EPA to establish municipal waste combustor (MWC) emissions limits for particulate matter, opacity, hydrogen chloride, sulfur dioxide, nitrogen oxides, carbon monoxide, dioxins, dibenzofurans, cadmium, lead, and mercury. Revised MWC air pollution regulations were subsequently proposed by EPA on September 20, 1994, and promulgated on December 19, 1995. The MWC emission limits were based on the application of maximum achievable control technology (MACT). This paper provides a brief overview of MWC technologies, a summary of EPA`s revised air pollution rules for MWCs, a review of current knowledge concerning formation and control of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans, and a discussion of the behavior and control of mercury in MWC flue gases. 56 refs., 11 figs., 3 tabs.

Kolgroe, J.D. [Environmental Protection Agency, Research Triangle Park, NC (United States). National Risk Management Research Lab.; Licata, A. [Licata Energy and Environmental Consultants, Inc., Yonkers, NY (United States)

1996-09-01T23:59:59.000Z

334

Relationship Between Composition and Toxicity of Engine Emissions...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Emissions Relationship Between Composition and Toxicity of Engine Emissions 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: Lovelace Respiratory Research...

335

Ultra supercritical turbines--steam oxidation  

SciTech Connect (OSTI)

Ultra supercritical (USC) power plants offer the promise of higher efficiencies and lower emissions, which are goals of the U.S. Department of Energy?s Advanced Power Systems Initiatives. Most current coal power plants in the U.S. operate at a maximum steam temperature of 538?C. However, new supercritical plants worldwide are being brought into service with steam temperatures of up to 620?C. Current Advanced Power Systems goals include coal generation at 60% efficiency, which would require steam temperatures of up to 760?C. This research examines the steamside oxidation of advanced alloys for use in USC systems, with emphasis placed on alloys for high- and intermediate-pressure turbine sections. Initial results of this research are presented.

Holcomb, Gordon R.; Covino, Bernard S., Jr.; Bullard, Sophie J.; Cramer, Stephen D.; Ziomek-Moroz, Margaret; Alman, David E.

2004-01-01T23:59:59.000Z

336

Graphene and Graphene Oxide: Biofunctionalization and Applications...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and Graphene Oxide: Biofunctionalization and Applications in Biotechnology. Graphene and Graphene Oxide: Biofunctionalization and Applications in Biotechnology. Abstract: Graphene...

337

Reading for Thursday Emissions scenario summary  

E-Print Network [OSTI]

emissions, for year 2000 #12;USA ­ CO2 emissions from fossil fuel combustion (2005) US EPA #12 of global rise in sea level red: reconstructed blue: tide gauges black: satellite #12;Other changes GHG emissions #12;

Schweik, Charles M.

338

Diesel emission control: Catalytic filters for particulate removal  

Science Journals Connector (OSTI)

The European diesel engine industry represents a vital sector across the Continent, with more than 2 million direct work positions and a turnover of over 400 billion Euro. Diesel engines provide large paybacks to society since they are extensively used to transport goods, services and people. In recent years increasing attention has been paid to the emissions from diesel engines which, like gasoline engine emissions, include carbon monoxide (CO), hydrocarbons (HC) and oxides of nitrogen (NOx). Diesel engines also produce significant levels of particulate matter (PM), which consists mostly of carbonaceous soot and a soluble organic fraction (SOF) of hydrocarbons that have condensed on the soot.Meeting the emission levels imposed for NOx and PM by legislation (Euro IV in 2005 and, in the 2008 perspective, Euro V) requires the development of a number of critical technologies to fulfill these very stringent emission limits (e.g. 0.005 g/km for PM). This review is focused on these innovative technologies with special reference to catalytic traps for diesel particulate removal.

Debora Fino

2007-01-01T23:59:59.000Z

339

NETL: Emissions Characterization - Adv. Low-NOx Burner Emissions  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Advanced Low-NOx Burner Emissions Characterization Advanced Low-NOx Burner Emissions Characterization The goal of this work is to develop a comprehensive, high-quality database characterizing PM2.5 emissions from utility plants firing high sulfur coals. The specific objectives are to: 1) develop and test an ultra low-NOx pulverized coal burner for plug-in retrofit applications without boiler wall tube modifications, 2) assess the impact of low-NOx PC burner operation on NOx and PM2.5 emissions, and 3) provide high-quality data to ensure that future PM2.5 regulations are based on good scientific information. The work will be performed in the Clean Environment Development Facility (CEDF), a 100 million Btu/hr near-full-scale facility located at the Alliance Research Center. Related Papers and Publications:

340

Appendix: Mercury Emissions used in CAM-Chem/Hg model. 1. Anthropogenic emissions  

E-Print Network [OSTI]

Appendix: Mercury Emissions used in CAM-Chem/Hg model. 1. Anthropogenic emissions The anthropogenic emission of mercury is directly adopted from global mercury emission inventory [Pacyna et al., 2005]. The anthropogenic emissions are shown in annual averaged total mercury emissions. (Unit: µg/m2 /day) 2. Land

Meskhidze, Nicholas

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Wildland fire emissions, carbon, and climate: U.S. emissions inventories Narasimhan K. Larkin a,  

E-Print Network [OSTI]

Wildland fire emissions, carbon, and climate: U.S. emissions inventories Narasimhan K. Larkin a: Fire emissions Emissions inventories Greenhouse gases a b s t r a c t Emissions from wildland fire fire emissions change considerably due to fluctuations from year to year with overall fire season

342

Innovative technical advances in the application of regenerative thermal oxidizers  

SciTech Connect (OSTI)

Regenerative Thermal Oxidizers (RTOs) have been applied in industry for over twenty (20) years to reduce the emissions of Volatile Organic compounds (VOCs) into the atmosphere from industrial process emissions. The Clean Air Act and its amendments have established a regulatory framework setting standards for allowable levels of VOC emissions. Several forces are driving the increasing use and acceptance of this technology: (1) High efficiency and increasing stringent standards require higher destruction efficiency; (2) Low operating cost and control of emission streams with less VOCs (therefore, less fuel value) causing higher use of natural gas for combustion; (3) Low NO{sub x}--the overlapping concern of NO{sub x} generation from the combustion process; (4) Low process upsets with improved productivity of industrial process require continuous integration of VOC abatement equipment; and (5) Reduced capital cost--capital cost criteria is $/ton of VOC abated. The latest development in RTO technology is the Single Can Oxidizer (SCO). This regenerative thermal oxidizer is the accumulation of developments in many subsystems of RTOs, combined with a dramatic new configuration. Several features of the system offer unique benefits to industrial end users: (1) Single can configuration gives reduced weight, material usage, and cost; (2) Rotary valve design gives smooth operation, and low pressure fluctuations; (3) Structured block heat recovery media reduces pressure drop, and lowers HP/operating cost; and (4) SMART system lowers NO{sub x} output/reduced operation cost. This paper will present a discussion of the features listed above. In addition, it will provide analytical documentation of test results for a full scale commercial unit.

Grzanka, R.; Truppi, T.

1999-07-01T23:59:59.000Z

343

Impact of N2 dilution on combustion and emissions in a spark ignition CNG engine  

Science Journals Connector (OSTI)

Abstract In order to reduce \\{NOx\\} (nitrogen oxides) emissions, N2 (nitrogen) was introduced as dilution gas to dilute mixture with a specially-designed injection device. The impacts of varying N2 DR (dilution ratio) on the combustion and the exhaust emissions were investigated, including engine heat release rate, indicator diagram, NOx, CO (carbon monoxide), THC (total hydrocarbon) emissions and so on. For this study, a modified 6.6 L CNG (compressed natural gas) engine was tested and N2 was injected into the end of intake manifold by a specially-designed device. The results showed that N2 dilution has a significant influence on the combustion and the exhaust emissions. With the rise of N2 DR, the maximum of pressure in cylinder and the maximum of heat release rate exhibited decrease trends, the centre of heat release curve showed a moving backward tendency. Higher N2 DR exhibited lower \\{NOx\\} (17–81%) emissions, but higher emissions of THC (3–78%) and CO (1–28%). The change of BSFC (brake specific fuel consumption) can be ignored with N2 DR no more than 167%. Satisfactory results can be obtained, with lower \\{NOx\\} (31%) emissions, lower BSFC (0.5%), and relatively higher THC (6%) and CO (1%) emissions, when N2 DR is 67%.

Zhongshu Wang; Hongbin Zuo; Zhongchang Liu; Weifeng Li; Huili Dou

2014-01-01T23:59:59.000Z

344

Radionuclide Air Emissions Report for 2012  

E-Print Network [OSTI]

Air Emissions Annual Reports for DOE Sites,” memo tooffices providing guidance for report preparation (March 22,470E-2012 Radionuclide Air Emission Report for Prepared by

Wahl, Linnea

2014-01-01T23:59:59.000Z

345

Demonstrating Fuel Consumption and Emissions Reductions with...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Fuel Consumption and Emissions Reductions with Next Generation Model-Based Diesel Engine Control Demonstrating Fuel Consumption and Emissions Reductions with Next Generation...

346

Diesel Engine Emission Reduction (DEER) Experiment | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Emission Reduction (DEER) Experiment Diesel Engine Emission Reduction (DEER) Experiment Presentation given at DEER 2006, August 20-24, 2006, Detroit, Michigan. Sponsored by the...

347

Collaborative Emissions Research at EMSL | EMSL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Collaborative Emissions Research at EMSL Collaborative Emissions Research at EMSL EMSL produced this video for the annual congressional science expo organized by the National User...

348

Low Emissions Asian Development (LEAD) Program - Bangladesh ...  

Open Energy Info (EERE)

Redirect page Jump to: navigation, search REDIRECT Low Emissions Asian Development (LEAD) Program Retrieved from "http:en.openei.orgwindex.php?titleLowEmissionsAsianDevel...

349

School Bus Emissions Study | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

School Bus Emissions Study School Bus Emissions Study 2003 DEER Conference Presentation: international Truck and Engine Corporation deer2003slodowske.pdf More Documents &...

350

Particle Number & Particulate Mass Emissions Measurements on...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Number & Particulate Mass Emissions Measurements on a 'Euro VI' Heavy-duty Engine using the PMP Methodologies Particle Number & Particulate Mass Emissions Measurements on a 'Euro...

351

Characterizing Test Methods and Emissions Reduction Performance...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Test Methods and Emissions Reduction Performance of In-Use Diesel Retrofit Technologies from the National Clean Diesel Campaign Characterizing Test Methods and Emissions Reduction...

352

Vehicle Technologies Office: Emission Control | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Batteries Fuel Efficiency & Emissions Combustion Engines Fuel Effects on Combustion Idle Reduction Emissions Waste Heat Recovery Lightweighting Parasitic Loss Reduction Lubricants...

353

Vehicle Technologies Office: Fuel Efficiency and Emissions |...  

Broader source: Energy.gov (indexed) [DOE]

Batteries Fuel Efficiency & Emissions Combustion Engines Fuel Effects on Combustion Idle Reduction Emissions Waste Heat Recovery Lightweighting Parasitic Loss Reduction Lubricants...

354

Measurement and Characterization of Unregulated Emissions from...  

Broader source: Energy.gov (indexed) [DOE]

More Documents & Publications Ethanol Effects on Lean-Burn and Stoichiometric GDI Emissions Measurement and Characterization of Unregulated Emissions from Advanced...

355

Particulate Emissions Control by Advanced Filtration Systems...  

Broader source: Energy.gov (indexed) [DOE]

Particulate Emissions Control by Advanced Filtration Systems or GDI Engines Particulate Emissions Control by Advanced Filtration Systems or GDI Engines 2013 DOE Hydrogen and Fuel...

356

Corporate response to emissions trading in Lithuania  

Science Journals Connector (OSTI)

The article highlights the preconditions for emissions trading in Lithuania, identifies the factors that influence ... competitive advantage via participation in the European Union Emissions Trading Scheme (EU ET...

R?ta Bubnien?

2008-01-01T23:59:59.000Z

357

Integrated Nozzle Flow, Spray, Combustion, & Emission Modeling...  

Broader source: Energy.gov (indexed) [DOE]

Spray, Combustion, & Emission Modeling using KH-ACT Primary Breakup Model & Detailed Chemistry Integrated Nozzle Flow, Spray, Combustion, & Emission Modeling using KH-ACT Primary...

358

Integrated Nozzle Flow, Spray, Combustion, & Emission Modeling...  

Broader source: Energy.gov (indexed) [DOE]

Combustion, and Emission Modeling Using KH-ACT Primary Breakup Model & Detailed Chemistry Sibendu Som, Douglas E. Longman Engine and Emissions Group (Energy Systems Division)...

359

Club Convergence in Carbon Dioxide Emissions  

Science Journals Connector (OSTI)

We examine convergence in carbon dioxide emissions among 128 countries for the period 1960–...2 emissions among all the countries under scrutiny in...

Ekaterini Panopoulou; Theologos Pantelidis

2009-09-01T23:59:59.000Z

360

Carbon Emissions: Petroleum Refining Industry  

U.S. Energy Information Administration (EIA) Indexed Site

Petroleum Refining Industry Petroleum Refining Industry Carbon Emissions in the Petroleum Refining Industry The Industry at a Glance, 1994 (SIC Code: 2911) Total Energy-Related Emissions: 79.9 million metric tons of carbon (MMTC) -- Pct. of All Manufacturers: 21.5% -- Nonfuel Emissions: 16.5 MMTC Total First Use of Energy: 6,263 trillion Btu -- Pct. of All Manufacturers: 28.9% Nonfuel Use of Energy Sources: 3,110 trillion Btu (49.7%) -- Naphthas and Other Oils: 1,328 trillion Btu -- Asphalt and Road Oil: 1,224 trillion Btu -- Lubricants: 416 trillion Btu Carbon Intensity: 12.75 MMTC per quadrillion Btu Energy Information Administration, "1994 Manufacturing Energy Consumption Survey", "Monthly Refinery Report" for 1994, and Emissions of Greenhouse Gases in the United States 1998.

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Fuel Mix and Emissions Disclosure  

Broader source: Energy.gov [DOE]

In 2001, Nevada enacted legislation requiring the state’s electric utilities to provide details regarding the fuel mix and emissions of electric generation to their customers. Utilities must...

362

Exoelectron Emission from Synthetic Corundums  

Science Journals Connector (OSTI)

...Radiation Protection Dosimetry Article Exoelectron Emission from Synthetic Corundums M. Yousif Charif R. Gout J. Barthe M. Petel Corundums (Alpha Al2O3) have been synthesised by the thermal dehydration of hydrargilite (Al2O3, H2O......

M. Yousif Charif; R. Gout; J. Barthe; M. Petel

1983-05-01T23:59:59.000Z

363

Anomalous Emission from HII regions  

E-Print Network [OSTI]

Spinning dust appears to be the best explanation for the anomalous emission that has been observed at $\\sim 10-60$ GHz. One of the best examples of spinning dust comes from a HII region in the Perseus molecular cloud. Observations of other HII regions also show tentative evidence for excess emission at frequencies $\\sim 30$ GHz, although at lower emissivity levels. A new detection of excess emission at 31 GHz in the HII region RCW175 has been made. The most plausible explanation again comes from spinning dust. HII regions are a good place to look for spinning dust as long as accurate radio data spanning the $\\sim 5-100$ GHz range is available.

C. Dickinson

2008-08-04T23:59:59.000Z

364

Fuel Mix and Emissions Disclosure  

Broader source: Energy.gov [DOE]

Iowa adopted regulations in 2003 that generally require rate-regulated electric utilities to disclose to customers the fuel mix and estimated emissions, in pounds per megawatt-hour (MWh), of...

365

Greenhouse Gases and Emissions Trading  

Science Journals Connector (OSTI)

Atmospheric concentrations of carbon dioxide and other greenhouse gases have grown rapidly since the beginning of this century. Unless emissions are controlled, the world could face rapid climate changes, incl...

Alice LeBlanc; Daniel J. Dudek

1993-01-01T23:59:59.000Z

366

1770 emissions trading system [n  

Science Journals Connector (OSTI)

envir. pol. (As permitted by the Kyoto Protocol of 1997, the sale of unused quotas of carbon dioxide [CO2] emissions to other countries, which can then use them as credits for their own accounts. The...

2010-01-01T23:59:59.000Z

367

Fuel Mix and Emissions Disclosure  

Broader source: Energy.gov [DOE]

Rhode Island requires all entities that sell electricity in the state to disclose details regarding the fuel mix and emissions of their electric generation to end-use customers. This information...

368

Organically Capped Silicon Nanoparticles with Blue Photoluminescence Prepared by Hydrosilylation Followed by Oxidation  

E-Print Network [OSTI]

-emitting silicon nanoparticles that are dispersible in common organic solvents is presented. Oxidation of yellow the nanoparticles to form stable, clear colloidal dispersions in organic solvents and provides for the possibility silicon nanoparticles with green through near-infrared emission, this enables the efficient and scalable

Swihart, Mark T.

369

A Planar Anode -Supported Solid Oxide Fuel Cell Model with Internal Reforming of Natural Gas  

E-Print Network [OSTI]

1 A Planar Anode - Supported Solid Oxide Fuel Cell Model with Internal Reforming of Natural Gas of natural gas has been developed. The model simultaneously solves mass, energy transport equations emission level, and multiple fuel utilization. SOFC can operate with various kinds of fuels such as natural

Boyer, Edmond

370

Investigation of zinc oxide doped with metal impurities for use as thin film conductive phosphors  

E-Print Network [OSTI]

of a viable flat panel display, low voltage, conductive phosphors which emit blue, red, and green light will be required for the field emission technology. This thesis examines zinc oxide (ZnO) based thin ( ) phosphors for such an application. ZnO is a...

Evatt, Steven R.

1994-01-01T23:59:59.000Z

371

Effect of E85 on Tailpipe Emissions from Light-Duty Vehicles  

SciTech Connect (OSTI)

E85, which consists of nominally 85% fuel grade ethanol and 15% gasoline, must be used in flexible-fuel (or 'flexfuel') vehicles (FFVs) that can operate on fuel with an ethanol content of 0-85%. Published studies include measurements of the effect of E85 on tailpipe emissions for Tier 1 and older vehicles. Car manufacturers have also supplied a large body of FFV certification data to the U.S. Environmental Protection Agency, primarily on Tier 2 vehicles. These studies and certification data reveal wide variability in the effects of E85 on emissions from different vehicles. Comparing Tier 1 FFVs running on E85 to similar non-FFVs running on gasoline showed, on average, significant reductions in emissions of oxides of nitrogen (NOx; 54%), non-methane hydrocarbons (NMHCs; 27%), and carbon monoxide (CO; 18%) for E85. Comparing Tier 2 FFVs running on E85 and comparable non-FFVs running on gasoline shows, for E85 on average, a significant reduction in emissions of CO (20%), and no significant effect on emissions of non-methane organic gases (NMOGs). NOx emissions from Tier 2 FFVs averaged approximately 28% less than comparable non-FFVs. However, perhaps because of the wide range of Tier 2 NOx standards, the absolute difference in NOx emissions between Tier 2 FFVs and non-FFVs is not significant (P 0.28). It is interesting that Tier 2 FFVs operating on gasoline produced approximately 13% less NMOGs than non-FFVs operating on gasoline. The data for Tier 1 vehicles show that E85 will cause significant reductions in emissions of benzene and butadiene, and significant increases in emissions of formaldehyde and acetaldehyde, in comparison to emissions from gasoline in both FFVs and non-FFVs. The compound that makes up the largest proportion of organic emissions from E85-fueled FFVs is ethanol.

Yanowitz, J.; McCormick, R. L.

2009-02-01T23:59:59.000Z

372

Alternative Fuels Data Center: Emissions Reduction Credits  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

Emissions Reduction Emissions Reduction Credits to someone by E-mail Share Alternative Fuels Data Center: Emissions Reduction Credits on Facebook Tweet about Alternative Fuels Data Center: Emissions Reduction Credits on Twitter Bookmark Alternative Fuels Data Center: Emissions Reduction Credits on Google Bookmark Alternative Fuels Data Center: Emissions Reduction Credits on Delicious Rank Alternative Fuels Data Center: Emissions Reduction Credits on Digg Find More places to share Alternative Fuels Data Center: Emissions Reduction Credits on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Emissions Reduction Credits Any state mobile emissions reduction credits program must allow credits for emissions reductions achieved by converting a vehicle to operate on an

373

Emissions from street vendor cooking devices (charcoal grilling). Final report, January 1998--March 1999  

SciTech Connect (OSTI)

The report discusses a joint US/Mexican program to establish a reliable emissions inventory for street vendor cooking devices (charcoal grilling), a significant source of air pollutants in the Mexicali-Imperial Valley area of Mexico. Emissions from these devices, prevalent in the streets of Mexicali, Mexico, were investigated experimentally by measuring levels of particulate matter, particle size distributions, volatile and semivolatile organic compounds, aldehydes, and oxides of nitrogen and sulfur, emitted when meat is cooked on a grill over a charcoal fire. To investigate the emission rate, both beef and chicken were tested. Furthermore, both meats were marinated with a mixture similar to that used by the street vendors. Some tests were conducted with non-marinated beef for comparison. Two blank runs were performed sampling charcoal fires without meat. Finally, a simple control device, normally used in an exhaust fan to trap grease over a kitchen stove, was evaluated for its effectiveness in reducing emissions.

Lee, S.Y.

1999-06-01T23:59:59.000Z

374

Exhaust emissions estimation during transient turbocharged diesel engine operation using a two-zone combustion model  

Science Journals Connector (OSTI)

A comprehensive, two-zone, transient, diesel combustion model is used to study the performance and exhaust emissions of a turbocharged diesel engine during load transients. Analytical modelling of fuel spray and in-cylinder processes is included, while detailed equations concerning all engine sub-systems describe the phenomena, which diversify transient operation from the steady-state. Demonstrative diagrams are provided for the time histories of nitric oxide (NO) and soot emissions during transient operation, and the main factors affecting their formation are highlighted. Moreover, in-cylinder development of NO concentration and soot density during individual transient cycles is provided and compared with their respective steady-state counterparts. This comparison points out the differences between steady-state and transient operation, as regards exhaust emissions development. The study is expanded with the investigation of load change magnitude and cylinder wall insulation effects on transient emissions.

C.D. Rakopoulos; A.M. Dimaratos; E.G. Giakoumis; D.C. Rakopoulos

2009-01-01T23:59:59.000Z

375

Emission Changes Resulting from the San Pedro Bay, California Ports Truck Retirement Program  

SciTech Connect (OSTI)

Recent U.S. Environmental Protection Agency emissions regulations have resulted in lower emissions of particulate matter and oxides of nitrogen from heavy-duty diesel trucks. To accelerate fleet turnover the State of California in 2008 along with the Ports of Los Angeles and Long Beach (San Pedro Bay Ports) in 2006 passed regulations establishing timelines forcing the retirement of older diesel trucks. On-road emissions measurements of heavy-duty diesel trucks were collected over a three-year period, beginning in 2008, at a Port of Los Angeles location and an inland weigh station on the Riverside freeway (CA SR91). At the Port location the mean fleet age decreased from 12.7 years in April of 2008 to 2.5 years in May of 2010 with significant reductions in carbon monoxide (30%), oxides of nitrogen (48%) and infrared opacity (a measure of particulate matter, 54%). We also observed a 20-fold increase in ammonia emissions as a result of new, stoichiometrically combusted, liquefied natural gas powered trucks. These results compare with changes at our inland site where the average ages were 7.9 years in April of 2008 and 8.3 years in April of 2010, with only small reductions in oxides of nitrogen (10%) being statistically significant. Both locations have experienced significant increases in nitrogen dioxide emissions from new trucks equipped with diesel particle filters; raising the mean nitrogen dioxide to oxides of nitrogen ratios from less than 10% to more than 30% at the Riverside freeway location.

Bishop, G. A.; Schuchmann, B. G.; Stedman, D. H.; Lawson, D. R.

2012-01-03T23:59:59.000Z

376

Emission Characteristics of a Diesel Engine Operating with In-Cylinder Gasoline and Diesel Fuel Blending  

SciTech Connect (OSTI)

Advanced combustion regimes such as homogeneous charge compression ignition (HCCI) and premixed charge compression ignition (PCCI) offer benefits of reduced nitrogen oxides (NOx) and particulate matter (PM) emissions. However, these combustion strategies often generate higher carbon monoxide (CO) and hydrocarbon (HC) emissions. In addition, aldehydes and ketone emissions can increase in these modes. In this study, the engine-out emissions of a compression-ignition engine operating in a fuel reactivity- controlled PCCI combustion mode using in-cylinder blending of gasoline and diesel fuel have been characterized. The work was performed on a 1.9-liter, 4-cylinder diesel engine outfitted with a port fuel injection system to deliver gasoline to the engine. The engine was operated at 2300 rpm and 4.2 bar brake mean effective pressure (BMEP) with the ratio of gasoline to diesel fuel that gave the highest engine efficiency and lowest emissions. Engine-out emissions for aldehydes, ketones and PM were compared with emissions from conventional diesel combustion. Sampling and analysis was carried out following micro-tunnel dilution of the exhaust. Particle geometric mean diameter, number-size distribution, and total number concentration were measured by a scanning mobility particle sizer (SMPS). For the particle mass measurements, samples were collected on Teflon-coated quartz-fiber filters and analyzed gravimetrically. Gaseous aldehydes and ketones were sampled using dinitrophenylhydrazine-coated solid phase extraction cartridges and the extracts were analyzed by liquid chromatography/mass spectrometry (LC/MS). In addition, emissions after a diesel oxidation catalyst (DOC) were also measured to investigate the destruction of CO, HC and formaldehydes by the catalyst.

Prikhodko, Vitaly Y [ORNL; Curran, Scott [ORNL; Barone, Teresa L [ORNL; Lewis Sr, Samuel Arthur [ORNL; Storey, John Morse [ORNL; Cho, Kukwon [ORNL; Wagner, Robert M [ORNL; Parks, II, James E [ORNL

2010-01-01T23:59:59.000Z

377

Oxidation resistant alloys, method for producing oxidation resistant alloys  

DOE Patents [OSTI]

A method for producing oxidation-resistant austenitic alloys for use at temperatures below 800.degree. C. comprising of: providing an alloy comprising, by weight %: 14-18% chromium, 15-18% nickel, 1-3% manganese, 1-2% molybdenum, 2-4% silicon, 0% aluminum and the balance being iron; heating the alloy to 800.degree. C. for between 175-250 hours prior to use in order to form a continuous silicon oxide film and another oxide film. The method provides a means of producing stainless steels with superior oxidation resistance at temperatures above 700.degree. C. at a low cost

Dunning, John S. (Corvallis, OR); Alman, David E. (Salem, OR)

2002-11-05T23:59:59.000Z

378

Oxidation resistant alloys, method for producing oxidation resistant alloys  

DOE Patents [OSTI]

A method for producing oxidation-resistant austenitic alloys for use at temperatures below 800 C. comprising of: providing an alloy comprising, by weight %: 14-18% chromium, 15-18% nickel, 1-3% manganese, 1-2% molybdenum, 2-4% silicon, 0% aluminum and the balance being iron; heating the alloy to 800 C. for between 175-250 hours prior to use in order to form a continuous silicon oxide film and another oxide film. The method provides a means of producing stainless steels with superior oxidation resistance at temperatures above 700 C. at a low cost

Dunning, John S.; Alman, David E.

2002-11-05T23:59:59.000Z

379

PHEV Engine Cold Start Emissions Management  

Broader source: Energy.gov [DOE]

Coordination of engine and powertrain supervisory control strategies to minimize cold start emissions

380

7, 68436902, 2007 An Asian emission  

E-Print Network [OSTI]

ACPD 7, 6843­6902, 2007 An Asian emission inventory for the period 1980­2020 T. Ohara et al. Title Chemistry and Physics Discussions An Asian emission inventory of anthropogenic emission sources 7, 6843­6902, 2007 An Asian emission inventory for the period 1980­2020 T. Ohara et al. Title Page

Paris-Sud XI, Université de

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Compilationof Regional to Global Inventoriesof Anthropogenic Emissions  

E-Print Network [OSTI]

Compilationof Regional to Global Inventoriesof Anthropogenic Emissions CarmenM. Benkovitz, Hajime inventories of emissions of the trace species included in the study at the appropriate sectoral, spatial on emissions is also required at high resolution for the design of policies aimed at reducing emissions

382

Elf Atochem sets five-year emission targets  

SciTech Connect (OSTI)

As part of its first annual environmental report, released this month, Elf Atochem (Paris) has set targets for emission reductions at its sites for the next five years. Under the program, the company aims to slash the level of contaminants in discharge water by 30%; cut by half emissions of 17 [open quotes]priority[close quotes] substances-including ammonia, chlorofluorocarbons, vinyl chloride monomer, methyl methacrylate, aromatics, chlorinated solvent, ethylbenzene, and styrene-for which 1992 emissions totaled 15,996 m.t.; reduce nitrogen oxides (NO[sub x]) emissions by 25%; and increase the proportions of toxic waste treated in installations on the company's own sites, from 90% of 1992's 383,00 m.t., to 95%. Implementation of its environmental policy cost the company about F2 billion ($375 million), or 3.5%-4% of sales, in 1992. The policy focuses on safer and more efficient technologies, toxic emissions and waste, improving energy efficiency, and cooperation with customers and public authorities on the introduction of more environmentally friendly products. Atochem says it has led to a fourfold reduction in accidents at work between 1984 and 1992. Over the same period, water contamination at the company's French sites has been cut by 67%, measured against the French chemical industry association's [open quotes]water index[close quotes]. Some sites did even better than the average, with the Carling steam cracker complex in eastern France registering a drop in water contamination of more than 90% following a F150-million joint project with local French and German water authorities.

Young, I.

1993-04-21T23:59:59.000Z

383

Alternative Fuels Data Center: Ethanol Vehicle Emissions  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

Ethanol Vehicle Ethanol Vehicle Emissions to someone by E-mail Share Alternative Fuels Data Center: Ethanol Vehicle Emissions on Facebook Tweet about Alternative Fuels Data Center: Ethanol Vehicle Emissions on Twitter Bookmark Alternative Fuels Data Center: Ethanol Vehicle Emissions on Google Bookmark Alternative Fuels Data Center: Ethanol Vehicle Emissions on Delicious Rank Alternative Fuels Data Center: Ethanol Vehicle Emissions on Digg Find More places to share Alternative Fuels Data Center: Ethanol Vehicle Emissions on AddThis.com... More in this section... Ethanol Basics Benefits & Considerations Stations Vehicles Availability Conversions Emissions Laws & Incentives Ethanol Vehicle Emissions When blended with gasoline for use as a vehicle fuel, ethanol can offer some emissions benefits over gasoline, depending on vehicle type, engine

384

Alternative Fuels Data Center: Emissions Control Requirement  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

Emissions Control Emissions Control Requirement to someone by E-mail Share Alternative Fuels Data Center: Emissions Control Requirement on Facebook Tweet about Alternative Fuels Data Center: Emissions Control Requirement on Twitter Bookmark Alternative Fuels Data Center: Emissions Control Requirement on Google Bookmark Alternative Fuels Data Center: Emissions Control Requirement on Delicious Rank Alternative Fuels Data Center: Emissions Control Requirement on Digg Find More places to share Alternative Fuels Data Center: Emissions Control Requirement on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Emissions Control Requirement Heavy-duty diesel vehicles used to perform federally funded state public works contracts must be powered by engines with Level 3 emissions control

385

Alternative Fuels Data Center: Biodiesel Vehicle Emissions  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

Biodiesel Vehicle Biodiesel Vehicle Emissions to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Vehicle Emissions on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Vehicle Emissions on Twitter Bookmark Alternative Fuels Data Center: Biodiesel Vehicle Emissions on Google Bookmark Alternative Fuels Data Center: Biodiesel Vehicle Emissions on Delicious Rank Alternative Fuels Data Center: Biodiesel Vehicle Emissions on Digg Find More places to share Alternative Fuels Data Center: Biodiesel Vehicle Emissions on AddThis.com... More in this section... Biodiesel Basics Benefits & Considerations Stations Vehicles Availability Emissions Laws & Incentives Biodiesel Vehicle Emissions When used as a vehicle fuel, biodiesel offers some tailpipe and considerable greenhouse gas (GHG) emissions benefits over conventional

386

Enhanced Thermal Conductivity Oxide Fuels  

SciTech Connect (OSTI)

the purpose of this project was to investigate the feasibility of increasing the thermal conductivity of oxide fuels by adding small fractions of a high conductivity solid phase.

Alvin Solomon; Shripad Revankar; J. Kevin McCoy

2006-01-17T23:59:59.000Z

387

Anodic oxidation of zircaloy-2  

Science Journals Connector (OSTI)

The anodic polarization of zircaloy-2 in different electrolytic baths has been investigated in order to obtain thick oxide films with properties suitable for wear applications.

A. Conte; A. Borello; A. Cabrini

1976-07-01T23:59:59.000Z

388

Advanced Emissions Control Development Program  

SciTech Connect (OSTI)

Babcock & Wilcox (B&W) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using B&W?s new Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and the inorganic species hydrogen chloride and hydrogen fluoride.

A. P. Evans

1998-12-03T23:59:59.000Z

389

Advanced Emission Control Development Program.  

SciTech Connect (OSTI)

Babcock & Wilcox (B&W) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using B&W`s new Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and the inorganic species hydrogen chloride and hydrogen fluoride.

Evans, A.P.

1997-12-31T23:59:59.000Z

390

Emissions of greenhouse gases from the use of transportation fuels and electricity. Volume 1, Main text  

SciTech Connect (OSTI)

This report presents estimates of full fuel-cycle emissions of greenhouse gases from using transportation fuels and electricity. The data cover emissions of carbon dioxide (CO{sub 2}), methane, carbon monoxide, nitrous oxide, nitrogen oxides, and nonmethane organic compounds resulting from the end use of fuels, compression or liquefaction of gaseous transportation fuels, fuel distribution, fuel production, feedstock transport, feedstock recovery, manufacture of motor vehicles, maintenance of transportation systems, manufacture of materials used in major energy facilities, and changes in land use that result from using biomass-derived fuels. The results for electricity use are in grams of CO{sub 2}-equivalent emissions per kilowatt-hour of electricity delivered to end users and cover generating plants powered by coal, oil, natural gas, methanol, biomass, and nuclear energy. The transportation analysis compares CO{sub 2}-equivalent emissions, in grams per mile, from base-case gasoline and diesel fuel cycles with emissions from these alternative- fuel cycles: methanol from coal, natural gas, or wood; compressed or liquefied natural gas; synthetic natural gas from wood; ethanol from corn or wood; liquefied petroleum gas from oil or natural gas; hydrogen from nuclear or solar power; electricity from coal, uranium, oil, natural gas, biomass, or solar energy, used in battery-powered electric vehicles; and hydrogen and methanol used in fuel-cell vehicles.

DeLuchi, M.A. [California Univ., Davis, CA (United States)

1991-11-01T23:59:59.000Z

391

Indoor Secondary Pollutants from Household Product Emissions in the  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Indoor Secondary Pollutants from Household Product Emissions in the Indoor Secondary Pollutants from Household Product Emissions in the Presence of Ozone: A Bench-Scale Chamber Study Title Indoor Secondary Pollutants from Household Product Emissions in the Presence of Ozone: A Bench-Scale Chamber Study Publication Type Journal Article LBNL Report Number LBNL-58785 Year of Publication 2006 Authors Destaillats, Hugo, Melissa M. Lunden, Brett C. Singer, Beverly K. Coleman, Alfred T. Hodgson, Charles J. Weschler, and William W. Nazaroff Journal Environmental Science and Technology Volume 40 Start Page Chapter Pagination 4421-4428 Abstract Ozone-driven chemistry is a major source of indoor secondary pollutants of health concern. This study investigates secondary air pollutants formed from reactions between constituents of household products and ozone. Gas-phase product emissions were introduced along with ozone at constant rates into a 198-L Teflon-lined reaction chamber. Gas-phase concentrations of reactive terpenoids and oxidation products were measured. Formaldehyde was a predominant oxidation byproduct for the three studied products, with yields under most conditions of 20-30% with respect to ozone consumed. Acetaldehyde, acetone, glycolaldehyde, formic acid and acetic acid were each also detected for two or three of the products. Immediately upon mixing of reactants, a scanning mobility particle sizer detected particle nucleation events that were followed by a significant degree of ultrafine particle growth. The production of secondary gaseous pollutants and particles depended primarily on the ozone level and was influenced by other parameters such as the air-exchange rate. Hydroxyl radical concentrations in the range 0.04-200 × 105 molecules cm-3 were measured. OH concentrations were observed to vary strongly with residual ozone level in the chamber, which was in the range 1 - 25 ppb, as is consistent with expectations from a simplified kinetic model. In a separate test, we exposed the dry residue of two products to ozone in the chamber and observed the formation of gas-phase and particle-phase secondary oxidation products

392

Air emission inventory for the Idaho National Engineering Laboratory: 1994 emissions report  

SciTech Connect (OSTI)

This report Presents the 1994 update of the Air Emission inventory for the Idaho National Engineering Laboratory (INEL). The INEL Air Emission Inventory documents sources and emissions of non-radionuclide pollutants from operations at the INEL. The report describes the emission inventory process and all of the sources at the INEL, and provides non-radionuclide emissions estimates for stationary sources.

NONE

1995-07-01T23:59:59.000Z

393

Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory - Calendar Year 1999 Emission Report  

SciTech Connect (OSTI)

This report presents the 1999 calendar year update of the Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL Air Emission Inventory documents sources and emissions of nonradionuclide pollutants from operations at the INEEL. The report describes the emission inventory process and all of the sources at the INEEL, and provides nonradionuclide emissions estimates for stationary sources.

Zohner, S.K.

2000-05-30T23:59:59.000Z

394

Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory - Calendar Year 1998 Emissions Report  

SciTech Connect (OSTI)

This report presents the 1998 calendar year update of the Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL Air Emission Inventory documents sources and emissions of nonradionuclide pollutants from operations at the INEEL. The report describes the emission inventory process and all of the sources at the INEEL, and provides nonradiological emissions estimates for stationary sources.

S. K. Zohner

1999-10-01T23:59:59.000Z

395

Remote Sensing of Mobile Source Air Pollutant Emissions: Variability and Uncertainty in On-Road Emissions  

E-Print Network [OSTI]

-Road Emissions Estimates of Carbon Monoxide and Hydrocarbons for School and Transit Buses Report No. FHWY/NC/97Remote Sensing of Mobile Source Air Pollutant Emissions: Variability and Uncertainty in On.0 INTRODUCTION 1 1.1 Mobile Source Emissions 2 1.2 Emission Regulations 2 1.3 Emissions Contributions of "Non

Frey, H. Christopher

396

Operation of staged membrane oxidation reactor systems  

SciTech Connect (OSTI)

A method of operating a multi-stage ion transport membrane oxidation system. The method comprises providing a multi-stage ion transport membrane oxidation system with at least a first membrane oxidation stage and a second membrane oxidation stage, operating the ion transport membrane oxidation system at operating conditions including a characteristic temperature of the first membrane oxidation stage and a characteristic temperature of the second membrane oxidation stage; and controlling the production capacity and/or the product quality by changing the characteristic temperature of the first membrane oxidation stage and/or changing the characteristic temperature of the second membrane oxidation stage.

Repasky, John Michael

2012-10-16T23:59:59.000Z

397

Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Data Report No. 2: NO{sub x} Adsorber Catalysts  

SciTech Connect (OSTI)

The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NOx) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim report discusses the results of the DECSE test program that demonstrates the potential of NOx adsorber catalyst technology across the range of diesel engine operation with a fuel economy penalty less than 4%.

DOE; ORNL; NREL; EMA; MECA

1999-10-15T23:59:59.000Z

398

NETL: CO2 Emissions Control  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Home > Technologies > Coal & Power Systems > Innovations for Existing Plants > CO2 Emissions Control Home > Technologies > Coal & Power Systems > Innovations for Existing Plants > CO2 Emissions Control Innovations for Existing Plants CO2 Emissions Control RD&D Roadmap Technology Update DOE/NETL Advanced CO2 Capture R&D Program: Technology Update DOE/NETL Advanced CO2 Capture R&D Program Accomplishments DOE/NETL Carbon Dioxide Capture and Storage RD&D Roadmap 2013 NETL CO2 Capture Technology Meeting Presentations DOE/NETL's Monthly Carbon Sequestration Newsletter Program Goals and Targets Pre-Combustion CO2 Control Post-Combustion CO2 Control Advanced Combustion CO2 Compression Other Systems Analysis Regulatory Drivers Reference Shelf Carbon capture involves the separation of CO2 from coal-based power plant flue gas or syngas. There are commercially available 1st-Generation CO2

399

Catalytic wet oxidation of phenolic wastes  

E-Print Network [OSTI]

Possible catalyst deactivation problems High capital, low operating Supercritical water oxidation (SCWO) Feasible only at high organic concentra- tions High Fast reaction, complete oxidation Severe reaction conditions, canosion problems... of milder reaction conditions and is much less energy intensive. Thus, catalytic wet oxidation would be an alternative to solvent extraction, supercritical water oxidation, homogeneous oxidation, and incineration. It should also be feasible at low...

Thomas, Brook James

1995-01-01T23:59:59.000Z

400

Low Temperature Constrained Sintering of Cerium Gadolinium Oxide Films for Solid Oxide Fuel Cell Applications  

E-Print Network [OSTI]

Temperature Solid Oxide Fuel Cells, In: S.C. Singhal and M.solidoxide.html, Tubular Solid Oxide Fuel Cell Technology,Oxide Films for Solid Oxide Fuel Cell Applications by Jason

Nicholas, Jason.D.

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Thermodynamics of Radiative Emission Processes  

Science Journals Connector (OSTI)

A basic assumption implicit in the application of thermodynamics to the electromagnetic field is that the laws of thermodynamics are locally valid for radiative emission and absorption processes. This means that a certain minimum amount of entropy must be created by the radiative process itself. It is shown, by considering the extreme case in which the spontaneous emission of a natural spectral line is the only process taking place, that this assumption is correct, and that its validity is essentially a consequence of the uncertainty principle as expressed by the reciprocal relationship between natural line breadth and lifetime.

M. A. Weinstein

1960-07-15T23:59:59.000Z

402

Oxidation of Mercury in Products of Coal Combustion  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Heng Ban Heng Ban Principal Investigator University of Alabama at Birmingham 1150 10th Avenue South Birmingham, AL 35294-4461 205-934-0011 hban@uab.edu Environmental and Water Resources OxidatiOn Of Mercury in PrOducts Of cOal cOMbustiOn Background The 2005 Clean Air Mercury Rule will require significant reductions in mercury emissions from coal-fired power plants. A variety of mercury reduction technologies are under commercial development, but an improved understanding of the fundamental chemical mechanisms that control the transformations and capture of mercury in boilers and pollution control devices is required to achieve necessary performance and cost reduction levels. Oxidized mercury is more easily captured by pollution control devices, such as Selective

403

Application of solar photocatalytic oxidation to VOC-containing airstreams  

SciTech Connect (OSTI)

Researchers from the National Renewable Energy Laboratory (NREL) recently conducted two pilot-scale field tests located at McClellan Air Force Base (AFB) in Sacramento, California and at the Fort Carson US Army Installation in Colorado Springs, Colorado. The objective of the tests was to determine the effectiveness of solar-powered photocatalytic oxidation (PCO) treatment units for destroying emissions of chlorinated organic compounds (trichloroethylene and dichloroethylenes) from an air stripper at ambient temperature and destroying paint solvent emissions (toluene and MEK) from a painting facility at higher temperatures. Their goals for field testing these solar-driven systems was to gather real-world treatability data and establish that the systems maintained performance during the duration of the testing. This paper reports the results of these field tests.

Magrini, K.A.; Watt, A.S.; Boyd, L.C.; Wolfrum, E.J.; Larson, S.A.; Roth, C.; Glatzmaier, G.C.

1999-07-01T23:59:59.000Z

404

Hydrogen Production via Photolytic Oxidation of Aqueous Sodium Sulfite Solutions  

Science Journals Connector (OSTI)

Sulfur dioxide (SO2) emission from coal-burning power plants and refinery operations has been implicated as a cause of acid rain and other air pollution related problems. ... Compounding its impacts on the environment, there are multiple sources of SO2 emissions, fossil fuel combustion being a primary contributor. ... Figure 2. Effect of initial solution pH on H2 formation via photolytic oxidation of 0.025 M Na2SO3 aqueous solutions (initial solution pH: (a) 7.53 (SO32? + HCl); (b) 8.88 (SO32? + HCl); (c) 9.92 (original Na2SO3 solution); (d) 10.96 (SO32?:CO32? = 1:0.05); ...

Cunping Huang; Clovis A. Linkous; Olawale Adebiyi; Ali T-Raissi

2010-06-01T23:59:59.000Z

405

Lessons from Loscoe: the uncontrolled migration of landfill gas  

Science Journals Connector (OSTI)

...was considered of fundamental importance in determining...making the situation safe, even though in...with coal mining operations. In 1983 smells...central heating boiler had been ignited...different landfill operation and completion scenarios...how to improve the operation and engineering...

G. M. Williams; N. Aitkenhead

406

UNCONTROLLED SEIZURES AND BONE HEALTH AMONG ADULT EPILEPSY PATIENTS  

E-Print Network [OSTI]

-inducing AEDs (EIAEDs: none, 0%-50%, more than 50%); proportion of high-dose of AEDs (high-dose defined as utilization of AED dose higher than the one listed in the ATC/DDD 48: none, 0%- 50%, more than 50%) were tested by Chi Square test or Fisher exact test..., number of treatment AEDs, proportion of high-dose AEDs, and history of fractures. A 7 statistically significant difference was found in seizure status, gender, therapeutic category (monotherapy vs. polytherapy), VNS use, and proportion of EIAEDs...

Yamada, Mikiko

2013-12-31T23:59:59.000Z

407

DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

organisation conducting these activities should have an ITER approved QA Program or an ISO 9001 accredited quality system. The general requirements are detailed in ITER document...

408

Hidden and Uncontrolled – On the Emergence of Network Steganographic Threats  

Science Journals Connector (OSTI)

Network steganography is the art of hiding secret information within innocent network transmissions. Recent findings indicate that novel malware is increasingly using network steganography. Similarly, other ma...

Steffen Wendzel; Wojciech Mazurczyk…

2014-01-01T23:59:59.000Z

409

DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

& Remote Handling framework contract. Approval Process Name Action Affiliation Author Hamilton D. 15 Dec 2014:signed IODGDIPPSEPEDRH Co-Authors Reviewers Brown A. Lazarov D....

410

DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

MAI Machine Assembly and Installation (Section) MQP Management and Quality Program NDE Non-Destructive test and Examination PIA Protection Important Activity PIC Protection...

411

DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Page 10 of 10 HVPS High Voltage Power Supply I&C Instrumentation and Control IC H&CD Ion Cyclotron Heating & Current Drive IC-PSC IC H&CD Plant System Controller IDM ITER Document...

412

Steamside Oxidation Behavior of Experimental 9%Cr Steels  

SciTech Connect (OSTI)

Reducing emissions and increasing economic competitiveness require more efficient steam power plants that utilize fossil fuels. One of the major challenges in designing these plants is the availability of materials that can stand the supercritical and ultra-supercritical steam conditions at a competitive cost. There are several programs around the world developing new ferritic and austenitic steels for superheater and reheater tubes exposed to the advanced steam conditions. The new steels must possess properties better than current steels in terms of creep strength, steamside oxidation resistance, fireside corrosion resistance, and thermal fatigue resistance. This paper introduces a series of experimental 9%Cr steels containing Cu, Co, and Ti. Stability of the phases in the new steels is discussed and compared to the phases in the commercially available materials. The steels were tested under both the dry and moist conditions at 650ºC for their cyclical oxidation resistance. Results of oxidation tests are presented. Under the moist conditions, the experimental steels exhibited significantly less mass gain compared to the commercial P91 steel. Microstructural characterization of the scale revealed different oxide compositions.

Dogan, O.N.; Holcomb, G.R.; Alman, D.E.; Jablonski, P.D.

2007-10-01T23:59:59.000Z

413

Intelligent emissions controller for substance injection in the post-primary combustion zone of fossil-fired boilers  

DOE Patents [OSTI]

The control of emissions from fossil-fired boilers wherein an injection of substances above the primary combustion zone employs multi-layer feedforward artificial neural networks for modeling static nonlinear relationships between the distribution of injected substances into the upper region of the furnace and the emissions exiting the furnace. Multivariable nonlinear constrained optimization algorithms use the mathematical expressions from the artificial neural networks to provide the optimal substance distribution that minimizes emission levels for a given total substance injection rate. Based upon the optimal operating conditions from the optimization algorithms, the incremental substance cost per unit of emissions reduction, and the open-market price per unit of emissions reduction, the intelligent emissions controller allows for the determination of whether it is more cost-effective to achieve additional increments in emission reduction through the injection of additional substance or through the purchase of emission credits on the open market. This is of particular interest to fossil-fired electrical power plant operators. The intelligent emission controller is particularly adapted for determining the economical control of such pollutants as oxides of nitrogen (NO.sub.x) and carbon monoxide (CO) emitted by fossil-fired boilers by the selective introduction of multiple inputs of substances (such as natural gas, ammonia, oil, water-oil emulsion, coal-water slurry and/or urea, and combinations of these substances) above the primary combustion zone of fossil-fired boilers.

Reifman, Jaques (Western Springs, IL); Feldman, Earl E. (Willowbrook, IL); Wei, Thomas Y. C. (Downers Grove, IL); Glickert, Roger W. (Pittsburgh, PA)

2003-01-01T23:59:59.000Z

414

Metal oxide films on metal  

DOE Patents [OSTI]

A structure including a thin film of a conductive alkaline earth metal oxide selected from the group consisting of strontium ruthenium trioxide, calcium ruthenium trioxide, barium ruthenium trioxide, lanthanum-strontium cobalt oxide or mixed alkaline earth ruthenium trioxides thereof upon a thin film of a noble metal such as platinum is provided.

Wu, Xin D. (Los Alamos, NM); Tiwari, Prabhat (Los Alamos, NM)

1995-01-01T23:59:59.000Z

415

Ethylene Oxide for Soil Sterilization  

Science Journals Connector (OSTI)

... , this method may be time-consuming, and in view of the physical properties of ethylene oxide (solubility in water and boiling point 12-5 C.) it was considered ... consists of making up an aqueous solution to supply 2 or 4 c.c. of ethylene oxide in a given amount of water, using pre-chilled glassware and water. The ...

R. E. ROSE; R. W. BAILEY

1952-04-26T23:59:59.000Z

416

Alternative Fuels Data Center: Propane Vehicle Emissions  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

Vehicles » Propane Vehicles » Propane Printable Version Share this resource Send a link to Alternative Fuels Data Center: Propane Vehicle Emissions to someone by E-mail Share Alternative Fuels Data Center: Propane Vehicle Emissions on Facebook Tweet about Alternative Fuels Data Center: Propane Vehicle Emissions on Twitter Bookmark Alternative Fuels Data Center: Propane Vehicle Emissions on Google Bookmark Alternative Fuels Data Center: Propane Vehicle Emissions on Delicious Rank Alternative Fuels Data Center: Propane Vehicle Emissions on Digg Find More places to share Alternative Fuels Data Center: Propane Vehicle Emissions on AddThis.com... More in this section... Propane Basics Benefits & Considerations Stations Vehicles Availability Conversions Emissions Laws & Incentives Propane Vehicle Emissions

417

How the Carbon Emissions Were Estimated  

U.S. Energy Information Administration (EIA) Indexed Site

How the Carbon Emissions Were Estimated How the Carbon Emissions Were Estimated How the Carbon Emissions Were Estimated Carbon dioxide emissions are the main component of greenhouse gas emissions caused by human activity. Carbon dioxide is emitted mostly as a byproduct of the combustion of fossil fuels for energy, although certain industrial processes (e.g., cement manufacture) also emit carbon dioxide. The estimates of energy-related carbon emissions require both data on the energy use and carbon emissions coefficients relating energy use to the amount of carbon emitted. The Energy Information Administration (EIA) is the main source of data on U.S. energy use. Emissions of Greenhouse Gases in the United States 1998 used annual data provided by energy suppliers. However, to obtain more detail on how different sectors use energy, the emissions estimates in Energy and GHG Analysis rely data from on surveys of energy users, such as manufacturing establishments and commercial buildings.

418

Alternative Fuels Data Center: Emissions Reductions Grants  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

Emissions Reductions Emissions Reductions Grants to someone by E-mail Share Alternative Fuels Data Center: Emissions Reductions Grants on Facebook Tweet about Alternative Fuels Data Center: Emissions Reductions Grants on Twitter Bookmark Alternative Fuels Data Center: Emissions Reductions Grants on Google Bookmark Alternative Fuels Data Center: Emissions Reductions Grants on Delicious Rank Alternative Fuels Data Center: Emissions Reductions Grants on Digg Find More places to share Alternative Fuels Data Center: Emissions Reductions Grants on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Emissions Reductions Grants The Carl Moyer Memorial Air Quality Standards Attainment Program (Program) provides incentives to cover the incremental cost of purchasing engines and

419

Emission of polycyclic aromatic hydrocarbons in China  

SciTech Connect (OSTI)

Emission of 16 polycyclic aromatic hydrocarbons (PAHs) listed as U.S. Environmental Protection Agency (U.S. EPA) priority pollutants from major sources in China were compiled. Geographical distribution and temporal change of the PAH emission, as well as emission profiles, are discussed. It was estimated that the total PAH emission in China was 25,300 tons in 2003. The emission profile featured a relatively higher portion of high molecular weight (HMW) species with carcinogenic potential due to large contributions of domestic coal and coking industry. Among various sources, biomass burning, domestic coal combustion, and the coking industry contributed 60%, 20%, and 16% of the total emission, respectively. Total emission, emission density, emission intensity, and emission per capita showed geographical variations. In general, the southeastern provinces were characterized by higher emission density, while those in western and northern China featured higher emission intensity and population-normalized emission. Although energy consumption in China went up continuously during the past two decades, annual emission of PAHs fluctuated depending on the amount of domestic coal consumption, coke production, and the efficiency of energy utilization. 47 refs., 6 figs.

Shanshan Xu; Wenxin Liu; Shu Tao [Peking University, Beijing (China). Laboratory for Earth Surface Processes, College of Environmental Sciences

2006-02-01T23:59:59.000Z

420

Performance analysis and exhaust emissions of neem methyl ester operated compression ignition engine  

Science Journals Connector (OSTI)

Neem oil methyl ester (NOME) was prepared from neem oil using alkaline catalyzed transesterification. The important fuel properties of NOME 20% blend of NOME with diesel were compared with those of diesel. Optimum injection pressures were determined for neat diesel and NOME-20 blend. Comparison of brake specific fuel consumption (BSFC) brake thermal efficiency (BTE) exhaust gas temperature (EGT) and smoke density was done for diesel and NOME-20 blend at their respective optimum injection pressure. Higher BSFC a slight decrease in BTE and a sharp decrease in EGT and smoke density were recorded with NOME-20 blend. Emissions with NOME-20 blend were also compared with diesel emissions at their respective optimum injection pressures. Significant reductions in carbon monoxide hydrocarbon and oxides of nitrogen and increase in carbon-di-oxide were observed with NOME-20 blend. Hence neem biodiesel has an environmental importance over diesel and shows a promising future.

Vinod Singh Yadav; Kamal Kishore Khatri; Deepak Tanwar; Ajayta; Dilip Sharma; S. L. Soni

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Solid Oxide Fuel Cell Successfully Powers Truck Cab and Sleeper in  

Broader source: Energy.gov (indexed) [DOE]

Solid Oxide Fuel Cell Successfully Powers Truck Cab and Sleeper in Solid Oxide Fuel Cell Successfully Powers Truck Cab and Sleeper in DOE-Sponsored Test Solid Oxide Fuel Cell Successfully Powers Truck Cab and Sleeper in DOE-Sponsored Test March 19, 2009 - 1:00pm Addthis Washington, DC --In a test sponsored by the U.S. Department of Energy (DOE), a Delphi auxiliary power unit employing a solid oxide fuel cell (SOFC) successfully operated the electrical system and air conditioning of a Peterbilt Model 386 truck under conditions simulating idling conditions for 10 hours. The device provides an alternative to running a truck's main diesel engine, or using a truck's batteries, to power auxiliary electrical loads during rest periods, thereby lowering emissions, reducing noise, and saving fuel. In testing at Peterbilt Motors Company Texas head-quarters, a Delphi

422

Impact of Biofuel Blending on Diesel Soot Oxidation: Implications for Aftertreatment  

SciTech Connect (OSTI)

Control strategies for diesel particulate filters (DPFs) remain one of the most important aspects of aftertreatment research and understanding the soot oxidation mechanism is key to controlling regeneration. Currently, most DPF models contain simple, first order heterogeneous reactions oxidation models with empirically fit parameters. This work improves the understanding of fundamental oxidation kinetics necessary to advance the capabilities of predictive modeling, by leading to better control over regeneration of the device. This study investigated the effects of blending soybean-derived biodiesel fuel on diesel particulate emissions under conventional combustion from a 1.7L direct injection, common rail diesel engine. Five biofuel blend levels were investigated and compared to conventional certification diesel for the nanostructure, surface chemistry and major constituents of the soluble organic fraction (SOF) of diesel particulate matter (PM), and the relationship between these properties and the particulate oxidation kinetics.

Strzelec, Andrea [ORNL; Toops, Todd J [ORNL; Lewis Sr, Samuel Arthur [ORNL; Daw, C Stuart [ORNL; Foster, David [University of Wisconsin; Rutland, Prof. Christopher J. [University of Wisconsin; Vander Wal, Dr. Randy [NASA-Glenn Research Center, Cleveland

2009-01-01T23:59:59.000Z

423

GEIA-ACCENT Emission Data Portal | Open Energy Information  

Open Energy Info (EERE)

GEIA-ACCENT Emission Data Portal GEIA-ACCENT Emission Data Portal Jump to: navigation, search Tool Summary Name: Global Emissions Inventory Activity (GEIA) Agency/Company /Organization: National Aeronautics and Space Administration Sector: Energy, Land Topics: GHG inventory Resource Type: Dataset Website: www.geiacenter.org/ References: Global Emissions Inventory Activity (GEIA)[1] "The GEIA /ACCENT data portal provides gridded emission data; emission data are usually separated into three main categories : anthropogenic emissions, biomass burning emissions, and natural emissions: anthropogenic emissions include emissions from fossil fuel and biofuel consumption, industry and agricultural sources. biomass burning emissions include emissions from forest fires, savannah fires, and sometimes large croplands fires.

424

Gas Emissions FLOODING THE LAND,  

E-Print Network [OSTI]

signif- icant sources of emissions of the greenhouse gases carbon dioxide and, in particular, methane to bacteria breaking down organic matter in the water. Methane, a much more powerful greenhouse gas than coal plants generating the same amounts of power. Dams and their associated reservoirs are globally

Batiste, Oriol

425

Educational Multiwavelength Atomic Emission Spectrometer  

E-Print Network [OSTI]

atomic absorption is the capability for simultaneous multielement analysis. It can be used colleges had acquired atomic absorption instruments by the year 1990.[2] In contrast, atomic emission with the acetylene-air flame source taken from an existing atomic absorption instrument. Two spectrometer units

Nazarenko, Alexander

426

HYPERPARAMETER ESTIMATION FOR EMISSION COMPUTED  

E-Print Network [OSTI]

HYPERPARAMETER ESTIMATION FOR EMISSION COMPUTED TOMOGRAPHY DATA A. López (a) , R. Molina (b) (a limited due to several factors. These factors include the need of greater computational time than to the projection data to obtain two-dimensional slices or cross sections (images) of activity distribution. #12

Granada, Universidad de

427

Nanostructured Solid Oxide Fuel Cell Electrodes  

E-Print Network [OSTI]

post-Doping of Solid Oxide Fuel Cell Cathodes,? P.h.D.and V. I. Birss, in Solid Oxide Fuel Cells (SOFC IX), S. C.Nanostructured Solid Oxide Fuel Cell Electrodes By Tal Zvi

Sholklapper, Tal Zvi

2007-01-01T23:59:59.000Z

428

Detection of oxidation in human serum lipoproteins  

E-Print Network [OSTI]

A method for the oxidation of lipoproteins in vitro was developed using the free radical initiator, 2,2?-azobis-(2-amidinopropane) dihydrochloride (AAPH). Following in vitro oxidation, the susceptibility to oxidation of the serum samples...

Myers, Christine Lee

2006-04-12T23:59:59.000Z

429

Removing mercury from coal emissions: options for ash-friendly technologies  

SciTech Connect (OSTI)

The article gives a brief description of techniques to remove mercury emitted from coal-fired power plants and discusses environmental considerations associated with the effect of emission controls on coal fly ash. Techniques covered include use of injected mercury sorbents (activated carbon, metal oxide catalysts, MerCAP{trademark} and MercScreen{trademark}) and fuel cleaning. Technologies currently being researched are mentioned. 8 refs.

Sager, J. [United States Environmental Protection Agency (United States)

2009-07-01T23:59:59.000Z

430

New manganese catalyst for light alkane oxidation  

DOE Patents [OSTI]

Aluminophosphates containing manganese in the structural framework are employed for the oxidation of alkanes, for example the vapor phase oxidation of methane to methanol.

Durante, Vincent A. (West Chester, PA); Lyons, James E. (Wallingford, PA); Walker, Darrell W. (Visalia, CA); Marcus, Bonita K. (Radnor, PA)

1994-01-01T23:59:59.000Z

431

NETL: Advanced NOx Emissions Control: Control Technology - NOx Emissions  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Emissions from Multi-Burners Emissions from Multi-Burners The University of Utah working with Reaction Engineering International and Brigham Young University is investigating a project that consists of integrated experimental, theoretical and computational modeling efforts. The primary objective is to evaluate NOx formation/destruction processes as they occur in multi-burner arrays, a geometry almost always utilized in utility practice. Most controlled experimental work examining NOx has been conducted on single burners. The range of potential intra-burner interactions are likely to provide added degrees of freedom for reducing NOx. The resultant findings may allow existing utilities to arrange fuel and air distribution to minimize NOx. In new applications, orientation of individual burners within an array may also be altered to reduce NOx. Comprehensive combustion codes will be modified to incorporate the latest submodels of nitrogen release and heterogeneous chemistry. Comparison of pilot scale experiments and simulations will be utilized to validate/develop theory.

432

Health Impacts Research - Emissions & Emission Controls - FEERC  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Health Impacts Research Health Impacts Research Another aspect of the emissions research at ORNL focuses on Health Impacts. This effort concentrates on analyzing exhaust for Mobile Source Air Toxics (MSATs) or other unregulated exhaust species that have the potential to harm human health. MSATs are a group of chemical species defined by the U.S. EPA that may pose risk to humans; formaldehyde, acetaldehyde, acrolein, 1,3-butadiene, benzene, and toluene are some example species. Engines operated with new combustion modes and alternative fuels are studied for MSAT emissions to determine insure that the advanced technologies being developed pose no additional risk to humans. A large part of the Health Impacts research effort at ORNL focuses on particulate matter (PM) which is also defined as an MSAT by the U.S. EPA.

433

Controlling Formaldehyde Emissions with Boiler Ash  

Science Journals Connector (OSTI)

Regenerative thermal (2) or catalytic (3) oxidizers are presently used to control HAPs and other VOCs. ... In another, methanol and other VOCs released from the manufacture of printed circuit boards were trapped and concentrated in activated carbon beds before being oxidized (11). ... The capital cost of a fluidized bed is much lower than that of a thermal oxidizer, and the cost of natural gas required to operate the oxidizer is removed. ...

Jennifer Cowan; Malyuba Abu-Daabes; Sujit Banerjee

2005-06-02T23:59:59.000Z

434

Studies of oxidized hexagonal SiC surfaces and the  

Science Journals Connector (OSTI)

Results of recent photoemission studies of oxidation of hexagonal SiC surfaces and SiO2/SiC interfaces are reviewed and discussed. These investigations have focused on two main questions thought to have a significant effect on MOS device characteristics: the existence of carbon clusters or carbon-containing by-products and the existence of sub-oxides at the SiO2/SiC interface. The presentation is focused on Si-terminated surfaces of hexagonal n-type SiC(0001) crystals since they to date have been considered the most promising for device applications. The results reviewed show that no carbon clusters or carbon-containing by-product can be detected at the interface of in situ or ex situ grown samples with an oxide layer thickness larger than about 10 Å. Since the presence of carbon clusters was suggested in a recent scanning microscopy study it appears that they may exist, possibly depending on the sample preparation method used, but in such low concentrations that they are not detectable using photoemission. The presence of sub-oxides at the SiO2/SiC interface has been revealed in recorded Si 2p core level spectra by several groups. The results were not unanimous, however. The number of sub-oxides present and the shifts reported were different. The results of a recent study including also the Si 1s core level and Si KLL Auger transitions are therefore examined. These together with earlier Si 2p data show the presence of only one sub-oxide, assigned to Si1+ oxidation states, besides the fully developed SiO2 (Si4+). Possible reasons for the differences obtained earlier are discussed. That the sub-oxide is located at the interface is concluded from the relative intensity variations observed for the different components versus electron emission angle. An oxide thickness dependence of the SiO2 chemical shift in the core levels and Auger transitions is shown, similar to but smaller in magnitude than the thickness dependence revealed earlier for SiO2/Si. On cooled SiC(0001) substrates, adsorption of metastable molecular oxygen is suggested to occur in the initial oxidation stage like on the Si(111)-7 ? 7 surface. Oxidation results from the C-terminated surface and some preliminary results for the non-polar and surfaces are included and they show distinct differences both as regards the sub-oxides present and the amount of carbon-containing by-products at the interface in the initial oxidation stage compared to the Si-terminated SiC(0001) surface.

C Virojanadara; L I Johansson

2004-01-01T23:59:59.000Z

435

IGES GHG Emissions Data | Open Energy Information  

Open Energy Info (EERE)

IGES GHG Emissions Data IGES GHG Emissions Data Jump to: navigation, search Tool Summary LAUNCH TOOL Name: IGES GHG Emissions Data Agency/Company /Organization: Institute for Global Environmental Strategies Sector: Energy Topics: Baseline projection, GHG inventory Resource Type: Dataset Website: www.iges.or.jp/en/cdm/report_kyoto.html References: IGES GHG Emissions Data[1] Summary "IGES GHG Emissions Data is aimed at providing comprehensive, organised information on the GHG emissions from Annex I countries to the UNFCCC in an easy-to-understand way. All information is extracted from the publicly available sources on the UNFCCC web-site and this data will be updated regularly. " References ↑ "IGES GHG Emissions Data" Retrieved from "http://en.openei.org/w/index.php?title=IGES_GHG_Emissions_Data&oldid=383109"

436

Reducing Emissions in Plant Flaring Operations  

E-Print Network [OSTI]

, lowering emissions and maximizing production. Saving energy and reducing emissions are the internal requirements for every division of this major corporation. To achieve the public goals the company set, they issued a five year plan called Methods on Energy...

Duck, B.

2011-01-01T23:59:59.000Z

437

Quantitative Elemental Analyses by Plasma Emission Spectroscopy  

Science Journals Connector (OSTI)

...Elemental Analyses by Plasma Emission Spectroscopy...Argon-supported inductively coupled plasmas operated at atmospheric pressures are excellent...HIGH-FREQUENCY ARGON PLASMA FOR OPTICAL EMISSION...EXPERIMENTAL-STUDY OF A 1-KW, 50-MHZ RF INDUCTIVELY COUPLED...

Velmer A. Fassel

1978-10-13T23:59:59.000Z

438

Uncertainty in emissions projections for climate models  

E-Print Network [OSTI]

Future global climate projections are subject to large uncertainties. Major sources of this uncertainty are projections of anthropogenic emissions. We evaluate the uncertainty in future anthropogenic emissions using a ...

Webster, Mort David.; Babiker, Mustafa H.M.; Mayer, Monika.; Reilly, John M.; Harnisch, Jochen.; Hyman, Robert C.; Sarofim, Marcus C.; Wang, Chien.

439

Photon emission within the linear sigma model  

E-Print Network [OSTI]

Soft-photon emission rates are calculated within the linear sigma model. The investigation is aimed at answering the question to which extent the emissivities map out the phase structure of this particular effective model of strongly interacting matter.

F. Wunderlich; B. Kampfer

2014-12-22T23:59:59.000Z

440

SMB, X-ray Emission Spectroscopy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Emission Spectroscopy Beam Line 6-2b X-ray Emission Spectroscopy Beam Line 6-2b is an advanced spectroscopy experimental station on the multidisciplinary general user wiggler Beam...

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Dust Emission from the Perseus Molecular Cloud  

E-Print Network [OSTI]

Using far-infrared emission maps taken by IRAS and Spitzer and a near-infrared extinction map derived from 2MASS data, we have made dust temperature and column density maps of the Perseus molecular cloud. We show that the emission from transiently heated very small grains and the big grain dust emissivity vary as a function of extinction and dust temperature, with higher dust emissivities for colder grains. This variable emissivity can not be explained by temperature gradients along the line of sight or by noise in the emission maps, but is consistent with grain growth in the higher density and lower temperature regions. By accounting for the variations in the dust emissivity and VSG emission, we are able to map the temperature and column density of a nearby molecular cloud with better accuracy than has previously been possible.

S. Schnee; J. Li; A. A. Goodman; A. I. Sargent

2008-05-27T23:59:59.000Z

442

Global Mortality Attributable to Aircraft Cruise Emissions  

E-Print Network [OSTI]

Aircraft emissions impact human health though degradation of air quality. The majority of previous analyses of air quality impacts from aviation have considered only landing and takeoff emissions. We show that aircraft ...

Britter, Rex E.

443

Quantitative Elemental Analyses by Plasma Emission Spectroscopy  

Science Journals Connector (OSTI)

...Elemental Analyses by Plasma Emission Spectroscopy...inductively coupled plasmas operated at atmospheric...INDUCTIVELY-COUPLED HIGH-FREQUENCY ARGON PLASMA FOR OPTICAL EMISSION...1-KW, 50-MHZ RF INDUCTIVELY COUPLED...STUDIES OF A RADIO-FREQUENCY INDUCTIVELY COUPLED...

Velmer A. Fassel

1978-10-13T23:59:59.000Z

444

Electricity Generation and Emissions Reduction Decisions  

E-Print Network [OSTI]

Electricity Generation and Emissions Reduction Decisions under Policy Uncertainty: A General;1 Electricity Generation and Emissions Reduction Decisions under Policy Uncertainty: A General Equilibrium Analysis Jennifer Morris* , Mort Webster* and John Reilly* Abstract The electric power sector, which

445

ASSESSMENT OF BUILDING LIFECYLE CARBON EMISSIONS  

E-Print Network [OSTI]

Even though the Carbon Capture & Sequestration Technologies (CC & ST) program at the Massachusetts Institute of Technology initiated carbon emission research in late 1990s (CSI, 2013), carbon emissions has only become a hot topic in the last decade...

Kwok, George

2014-05-31T23:59:59.000Z

446

The implementation of emissions trading in companies  

Science Journals Connector (OSTI)

This paper investigates what activities large companies have undertaken to utilize emissions trading and/or offset projects as part of ... in home countries have affected corporate activity towards emissions trading

Jonatan Pinkse

2008-01-01T23:59:59.000Z

447

Companies and regulators in emissions trading programs  

Science Journals Connector (OSTI)

Much has been written about the economic and environmental performance of US emissions trading programs for “acid rain” (sulfur dioxide ... whether these features are present in the EU Emissions Trading System an...

Joseph Kruger

2008-01-01T23:59:59.000Z

448

Carbon Dioxide and Methane Emissions from Estuaries  

Science Journals Connector (OSTI)

Carbon dioxide and methane emissions from estuaries are reviewed in relation with biogeochemical processes and carbon cycling. In estuaries, carbon dioxide and methane emissions show a large spatial and temporal ...

Gwenaël Abril; Alberto Vieira Borges

2005-01-01T23:59:59.000Z

449

Absolute vs. intensity-based emission caps  

E-Print Network [OSTI]

Cap-and-trade systems limit emissions to some pre-specified absolute quantity. Intensity-based limits, that restrict emissions to some pre-specified rate relative to input or output, are much more widely used in environmental ...

Ellerman, A. Denny.

450

Comparative Study of Hybrid Powertrains on Fuel Saving, Emissions, and Component Energy Loss in HD Trucks  

SciTech Connect (OSTI)

We compared parallel and series hybrid powertrains on fuel economy, component energy loss, and emissions control in Class 8 trucks over both city and highway driving. A comprehensive set of component models describing battery energy, engine fuel efficiency, emissions control, and power demand interactions for heavy duty (HD) hybrids has been integrated with parallel and series hybrid Class 8 trucks in order to identify the technical barriers of these hybrid powertrain technologies. The results show that series hybrid is absolutely negative for fuel economy benefit of long-haul trucks due to an efficiency penalty associated with the dual-step conversions of energy (i.e. mechanical to electric to mechanical). The current parallel hybrid technology combined with 50% auxiliary load reduction could elevate 5-7% fuel economy of long-haul trucks, but a profound improvement of long-haul truck fuel economy requires additional innovative technologies for reducing aerodynamic drag and rolling resistance losses. The simulated emissions control indicates that hybrid trucks reduce more CO and HC emissions than conventional trucks. The simulated results further indicate that the catalyzed DPF played an important role in CO oxidations. Limited NH3 emissions could be slipped from the Urea SCR, but the average NH3 emissions are below 20 ppm. Meanwhile our estimations show 1.5-1.9% of equivalent fuel-cost penalty due to urea consumption in the simulated SCR cases.

Gao, Zhiming [ORNL; FINNEY, Charles E A [ORNL; Daw, C Stuart [ORNL; LaClair, Tim J [ORNL; Smith, David E [ORNL

2014-01-01T23:59:59.000Z

451

Combustion and emission characteristics of a turbocharged diesel engine using high premixed ratio of methanol and diesel fuel  

Science Journals Connector (OSTI)

Abstract The combustion and emission characteristics of a dual fuel diesel engine with high premixed ratio of methanol (PRm) were investigated. Experiments were performed on a 6-cylinder turbocharged, inter-cooling diesel engine. Methanol was injected through the intake port and ignited by direct injected diesel in the cylinder, the maximum \\{PRm\\} was over 70%. The experimental results showed that with high PRm, the maximum in-cylinder pressure increased from medium to high engine load but varied little or even decreased at low engine speed and load. High \\{PRm\\} prolonged the ignition delay but shortened the combustion duration and decreased the in-cylinder gas temperature at ignition timing. Hydrocarbons (HC), carbon monoxide (CO), formaldehyde emissions and the proportion of nitrogen dioxide (NO2) in nitrogen oxides (NOX) increased significantly with the increase of \\{PRm\\} while NOX and dry soot emissions were significantly reduced, which meant the trade-off relationship between NOX and soot emissions disappeared. The increased HC, CO and formaldehyde emissions could be effectively reduced by diesel oxidation catalyst (DOC) when the exhaust gas temperature reached the light off temperature of the DOC. After DOC, the NO2 proportion in NOX was greatly reduced to less than that of baseline engine at methanol premixed mode but increased slightly at pure diesel mode. The maximum \\{PRm\\} was confined by in-cylinder pressure at high engine speed and load. But at low engine speed and load, it was confined by the high emissions of HC, CO and formaldehyde even after DOC.

Lijiang Wei; Chunde Yao; Quangang Wang; Wang Pan; Guopeng Han

2015-01-01T23:59:59.000Z

452

The high energy emission from black holes  

E-Print Network [OSTI]

The origin of the high energy emission (X-rays and gamma-rays) from black holes is still a matter of debate. We present new evidence that hard X-ray emission in the low/hard state may not be dominated by thermal Comptonization. We present an alternative scenario for the origin of the high energy emission that is well suited to explain the high energy emission from GRO J1655-40.

M. D. Caballero-Garcia; J. M. Miller; E. Kuulkers

2007-11-06T23:59:59.000Z

453

Measurement and Characterization of Unregulated Emissions from...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

More Documents & Publications Measurement and Characterization of Unregulated Emissions from Advanced Technologies Effects of Advanced Combustion Technologies on...

454

NREL: Transportation Research - Emissions and Fuel Economy Analysis  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

greenhouse gas and pollutant emissions by advancing the development of new fuels and engines that deliver both high efficiency and reduced emissions. Emissions that result in...

455

Ethanol Effects on Lean-Burn and Stoichiometric GDI Emissions...  

Broader source: Energy.gov (indexed) [DOE]

Ethanol Effects on Lean-Burn and Stoichiometric GDI Emissions Ethanol Effects on Lean-Burn and Stoichiometric GDI Emissions Characterized particulate emissions from U.S.-legal...

456

An Automobile/Transit Emissions Evaluation of Southern California's Metrolink  

E-Print Network [OSTI]

percentile) Finn| Report: An Automobile~Transit EmissionsAn Automobile/Transit Emissions Evaluation of Southernregulation. or An Automobile/Transit Emissions Evaluation of

Barth, Matthew J.; Tadi, Ramakrishna R.

1995-01-01T23:59:59.000Z

457

High Engine Efficiency at 2010 Emissions | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Engine Efficiency at 2010 Emissions High Engine Efficiency at 2010 Emissions 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005deernelson.pdf...

458

Common Sources of Federal Greenhouse Gas Emissions | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Common Sources of Federal Greenhouse Gas Emissions Common Sources of Federal Greenhouse Gas Emissions Common Sources of Federal Greenhouse Gas Emissions...

459

Mass Correlation of Engine Emissions with Spectral Instruments...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Mass Correlation of Engine Emissions with Spectral Instruments Mass Correlation of Engine Emissions with Spectral Instruments 2004 Diesel Engine Emissions Reduction (DEER)...

460

Effect of Biodiesel Blends on NOx Emissions | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Biodiesel Blends on NOx Emissions Effect of Biodiesel Blends on NOx Emissions Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007)....

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

How Exhaust Emissions Drive Diesel Engine Fuel Efficiency | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

How Exhaust Emissions Drive Diesel Engine Fuel Efficiency How Exhaust Emissions Drive Diesel Engine Fuel Efficiency 2004 Diesel Engine Emissions Reduction (DEER) Conference...

462

Combustion Targets for Low Emissions and High Efficiency | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Targets for Low Emissions and High Efficiency Combustion Targets for Low Emissions and High Efficiency 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and...

463

Perspectives Regarding Diesel Engine Emissions Reduction in the...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Perspectives Regarding Diesel Engine Emissions Reduction in the Northeast Perspectives Regarding Diesel Engine Emissions Reduction in the Northeast 2004 Diesel Engine Emissions...

464

2010 Emissions from an Electronics Perspective | Department of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

10 Emissions from an Electronics Perspective 2010 Emissions from an Electronics Perspective 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters...

465

Amendment: Lifecycle Emissions Data Worksheet (December 30, 2008...  

Broader source: Energy.gov (indexed) [DOE]

Lifecycle Emissions Data Worksheet (December 30, 2008) Amendment: Lifecycle Emissions Data Worksheet (December 30, 2008) lew.xls Description Amendment: Lifecycle Emissions Data...

466

Attachment C - Summary GHG Emissions Data FINAL | Department...  

Broader source: Energy.gov (indexed) [DOE]

Attachment C - Summary GHG Emissions Data FINAL Attachment C - Summary GHG Emissions Data FINAL Attachment-C-Summary-GHG-Emissions-Data-FINAL.xlsx Description Attachment C -...

467

Design of Integrated Laboratory and Heavy-Duty Emissions Testing...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

of Integrated Laboratory and Heavy-Duty Emissions Testing Center Design of Integrated Laboratory and Heavy-Duty Emissions Testing Center Both simulated and actual diesel emissions...

468

TEMPORAL VARIATION OF LFG EMISSION FROM DIFFERENT TYPES OF  

E-Print Network [OSTI]

). This reduction of the landfill gas (LFG) emissions requires the ability to measure low methane emissions methane emissions were observed only near the landfill gas

Paris-Sud XI, Université de

469

The Advanced Collaborative Emissions Study Moving Forward with...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Moving Forward with Assessing the Emissions and Health Effects of New Diesel Technology The Advanced Collaborative Emissions Study Moving Forward with Assessing the Emissions and...

470

Performance of Johnson Matthey EGRT? Emission Control System...  

Broader source: Energy.gov (indexed) [DOE]

Performance of Johnson Matthey EGRT Emission Control System for NOx and PM Emission Reduction in Retrofit Applications Part 1 Performance of Johnson Matthey EGRT Emission...

471

Diesel and Gasoline Engine Emissions: Characterization of Atmosphere...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

and Gasoline Engine Emissions: Characterization of Atmosphere Composition and Health Responses to Inhaled Emissions Diesel and Gasoline Engine Emissions: Characterization of...

472

Carbon sequestration and greenhouse gas emissions in urban turf  

E-Print Network [OSTI]

D. C. Lal, R. (2004), Carbon emission from farm operations,facts: Average carbon dioxide emissions resulting fromcalculation of carbon dioxide (CO 2 ) emissions from fuel

Townsend-Small, Amy; Czimczik, Claudia I

2010-01-01T23:59:59.000Z

473

Emissions Inventory Report Summary: Reporting Requirements for the New Mexico Administrative Code, Title 20, Chapter 2, Part 73 (20 NMAC 2.73) for Calendar Year 2001  

SciTech Connect (OSTI)

Los Alamos National Laboratory is subject to annual emissions-reporting requirements for regulated air contaminants under Title 20 of the New Mexico Administrative Code, Chapter 2, Part 73 (20.2.73 NMAC), Notice of Intent and Emissions Inventory Requirements. The applicability of the requirements is based on the Laboratory's potential to emit 100 tons per year of suspended particulate matter, nitrogen oxides, carbon monoxide, sulfur oxides, or volatile organic compounds. For calendar year 2001, the Technical Area 3 steam plant was the primary source of criteria air pollutants from the Laboratory, while research and development activities were the primary source of volatile organic compounds. Emissions of beryllium and aluminum were reported for activities permitted under 20.2.72 NMAC. Hazardous air pollutant emissions from chemical use for research and development activities were also reported.

Margorie Stockton

2003-04-01T23:59:59.000Z

474

Energy Use and Carbon Emissions:  

Gasoline and Diesel Fuel Update (EIA)

World Energy Use and Carbon Dioxide Emissions, 1980-2001 World Energy Use and Carbon Dioxide Emissions, 1980-2001 April 2004 Energy Information Administration Contacts Staff from the Office of Energy Markets and End Use (EMEU), Energy Markets and Contingency Information Division (EMCID) prepared this report. General questions concerning the content of the report may be referred to Mark Rodekohr (Mark.Rodekohr@eia.doe.gov, 202-586-1130), Director of EMCID; or Lowell Feld (Lowell.Feld@eia.doe.gov, 202-586-9502), Leader of the Contingency Information Team. Specific questions about the report should be referred to Nathan Wilson (Nathan.Wilson@eia.doe.gov, 202-586-9883). 1 Table of Contents CONTACTS .......................................................................................................................

475

Spectral Emission of Moving Atom  

E-Print Network [OSTI]

A renewed analysis of the H.E. Ives and G.R. Stilwell's experiment on moving hydrogen canal rays (J. Opt. Soc. Am., 1938, v.28, 215) concludes that the spectral emission of a moving atom exhibits always a redshift which informs not the direction of the atom's motion. The conclusion is also evident from a simple energy relation: atomic spectral radiation is emitted as an orbiting electron consumes a portion of its internal energy on transiting to a lower-energy state which however has in a moving atom an additional energy gain; this results in a redshift in the emission frequency. Based on auxiliary experimental information and a scheme for de Broglie particle formation, we give a vigorous elucidation of the mechanism for deceleration radiation of atomic electron; the corresponding prediction of the redshift is in complete agreement with the Ives and Stilwell's experimental formula.

J. X. Zheng-Johansson

2008-03-17T23:59:59.000Z

476

Integrated Emissivity And Temperature Measurement  

DOE Patents [OSTI]

A multi-channel spectrometer and a light source are used to measure both the emitted and the reflected light from a surface which is at an elevated temperature relative to its environment. In a first method, the temperature of the surface and emissivity in each wavelength is calculated from a knowledge of the spectrum and the measurement of the incident and reflected light. In the second method, the reflected light is measured from a reference surface having a known reflectivity and the same geometry as the surface of interest and the emitted and the reflected light are measured for the surface of interest. These measurements permit the computation of the emissivity in each channel of the spectrometer and the temperature of the surface of interest.

Poulsen, Peter (Livermore, CA)

2005-11-08T23:59:59.000Z

477

emissions | OpenEI Community  

Open Energy Info (EERE)

4 4 Varnish cache server Home Groups Community Central Green Button Applications Developer Utility Rate FRED: FRee Energy Database More Public Groups Private Groups Features Groups Blog posts Content Stream Documents Discussions Polls Q & A Events Notices My stuff Energy blogs 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142228914 Varnish cache server emissions Home Graham7781's picture Submitted by Graham7781(2002) Super contributor 9 January, 2014 - 13:12 Suburbs offset Low Carbon Footprint of major U.S. Cities carbon cities CO2 emissions OpenEI suburbs US New research from the University of California-Berkeley shows that those who live in cities in the United States have significantly smaller per-capita carbon footprints than their suburban counterparts. The

478

Structure, adhesion, and stability of metal/oxide and oxide/oxide interfaces  

SciTech Connect (OSTI)

Studies of structural, electronic, and chemical properties of metal/oxide and oxide/oxide interfaces were performed on well-defined interfaces that created by depositing ultra-thin potassium and aluminum films and their oxides onto single crystal TiO[sub 2] and NiO surfaces. Work focused on determining the structure, growth mechanisms, and morphologies of metal and oxide films as they are deposited an single crystal oxide surfaces using RHEED and atomic force microscopy probing electronic structure, bonding and chemical interactions at the interfaces using x-ray and uv photoelectron spectroscopies (XPS, UPS) and Auger electron spectroscopy (AES), and understanding factors affecting stability and reactivity of the interface regions including the role of defects and impurities. Results indicate that kinetic effects have an important influence on interface structure and composition, and they also show that defects in the oxide substrate induce new electronic states at the interface which play a major role in cation-anion bonding and interface interactions. The results establish a link between electronic and chemical bonding properties and the interface structure and morphology, which is required to successfully manipulate the interfacial properties of advanced ceramic materials.

Lad, R.J.

1992-11-01T23:59:59.000Z

479

Reduction in air emissions attainable through implementation of district heating and cooling  

SciTech Connect (OSTI)

District heating and cooling (DHC) can provide multiple opportunities to reduce air emissions associated with space conditioning and electricity generation, which contribute 30% to 50% of all such emissions. When DHC is combined with cogeneration (CHP), maximum reductions in sulfur oxides (SO{sub x}), nitrogen oxides (NO{sub x}), carbon dioxide (CO{sub 2}), particulates, and ozone-depleting chlorofluorocarbon (CFC) refrigerants can most effectively be achieved. Although significant improvements in air quality have been documented in Europe and Scandinavia due to DHC and CHP implementation, accurately predicting such improvements has been difficult. Without acceptable quantification methods, regulatory bodies are reluctant to grant air emissions credits, and local community leaders are unwilling to invest in DHC and CHP as preferred methods of providing energy or strategies for air quality improvement. The recent development and release of a number of computer models designed specifically to provide quantification of air emissions that can result from DHC and CHP implementation should help provide local, state, and national policymakers with information vital to increasing support and investment in DHC development.

Bloomquist, R.G. [Washington State Energy Office, Olympia, WA (United States)

1996-12-31T23:59:59.000Z

480

Controlling the dynamics of spontaneous emission from  

E-Print Network [OSTI]

of spontaneous emission from quantum dots by photonic crystals Peter Lodahl1 , A. Floris van Driel2 , Ivan S emission can be manipulated10,11 . Photonic crystals provide such an environment: they strongly modify study spontaneous emission from semiconductor quantum dots embedded in inverse opal photonic crystals16

Vos, Willem L.

Note: This page contains sample records for the topic "oxides uncontrolled emission" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

CORONAL MAGNETIC FIELD MEASUREMENTS THROUGH GYRORESONANCE EMISSION  

E-Print Network [OSTI]

Chapter 5 CORONAL MAGNETIC FIELD MEASUREMENTS THROUGH GYRORESONANCE EMISSION Stephen M. White This article reviews the use of gyroresonance emission at radio wavelengths to measure coronal magnetic fields. Keywords: Sun, solar corona, solar magnetic fields, solar radio emission Introduction Since the realization

White, Stephen

482

8, 34053430, 2008 Climate and emission  

E-Print Network [OSTI]

ACPD 8, 3405­3430, 2008 Climate and emission changes over Canada and Mexico E. Tagaris et al. Title Chemistry and Physics Discussions The role of climate and emission changes in future air quality over.russell@ce.gatech.edu) 3405 #12;ACPD 8, 3405­3430, 2008 Climate and emission changes over Canada and Mexico E. Tagaris et al

Boyer, Edmond

483

4, 66916718, 2004 VOC emissions of  

E-Print Network [OSTI]

ACPD 4, 6691­6718, 2004 VOC emissions of Scots pine V. Tarvainen et al. Title Page Abstract Discussions Temperature and light dependence of the VOC emissions of Scots pine V. Tarvainen 1 , H. Hakola 1.tarvainen@fmi.fi) 6691 #12;ACPD 4, 6691­6718, 2004 VOC emissions of Scots pine V. Tarvainen et al. Title Page Abstract

Paris-Sud XI, Université de

484

5, 90979126, 2005 VOC emissions from  

E-Print Network [OSTI]

ACPD 5, 9097­9126, 2005 VOC emissions from vegetation pyrolysis J. P. Greenberg et al. Title Page Discussions Volatile organic emissions from the distillation and pyrolysis of vegetation J. P. Greenberg, H is licensed under a Creative Commons License. 9097 #12;ACPD 5, 9097­9126, 2005 VOC emissions from vegetation

Paris-Sud XI, Université de

485

Estimate Greenhouse Gas Emissions by Building Type  

Broader source: Energy.gov [DOE]

Starting with the programs contributing the greatest proportion of building greenhouse gas (GHG) emissions, the agency should next determine which building types operated by those programs use the most energy (Figure 1). Energy intensity is evaluated instead of emissions in this approach because programs may not have access to emissions data by building type.

486

Emissions Minimization Vehicle Routing Problem Miguel Figliozzi  

E-Print Network [OSTI]

. The level of GHG emissions is a proxy for fuel consumption in diesel engines and in the near future, the minimization of emissions and fuel consumption as the primary or secondary objective. This creates a new type, study, and solve a new vehicle routing problem where the minimization of emissions and fuel consumption

487

EPA expands air quality emissions trading policy  

Science Journals Connector (OSTI)

EPA expands air quality emissions trading policy ... The Environmental Protection Agency has expanded its old "bubble policy" into a wider-ranging, supposedly more effective, emissions trading program designed to speed up attainment of national air quality standards and save money. ... It also authorizes states to adopt generic emissions trading rules and extend these to all ... ...

1982-04-12T23:59:59.000Z

488

Energy Balance and Emissions Associated with Biochar  

E-Print Network [OSTI]

energy off- sets. 41­64% of these emission reductions are related to the retention of C in biochar offersanenergeticallyefficientstrategyforbioenergyproduction, and the land application of biochar reduces greenhouse emissions to a greater extent than when and contribute significantly to greenhouse gas emissions (1). Bioenergy produced from renewable biomass can

Lehmann, Johannes

489

NETL: IEP - Mercury Emissions Control: In-House R&D  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

In-House R&D In-House R&D The scrutiny of mercury (Hg) emissions from coal-fired utilities that began with the Clean Air Act Amendments of 1990 (CAAA) resulted in a determination by the U.S. EPA that such emissions should be regulated. A number of techniques for control of mercury emissions from power plants have been evaluated at various scales. One technique that received a great deal of attention by the EPA, utilities, and technology developers was dry sorbent injection upstream of an existing particulate control device. The in-house, air toxics research effort at NETL consisted of two distinct efforts: the first was aimed at characterizing an existing pilot unit for distribution and fate of hazardous air pollutants, including mercury ; the second was examining sorbents and photochemical oxidation as means for mercury removal from flue gas at laboratory-scale.

490

Reductions of NO{sub x} emissions on oil and gas firing at Bowline Unit 1  

SciTech Connect (OSTI)

In response to the NYSDEC, Part 227 regulations for the emissions of nitrogen oxides (NO{sub x}), Orange and Rockland Utilities, Inc. (ORU) and Burns & Roe Company (BRC) evaluated the options available to reduce the NO{sub x} emissions at two oil and gas fired units at Bowline Point Generating Station. Replacement of all of the existing burners with new low NO{sub x} burners and possibly overfire air ports presents the most costly method of achieving this goal. Therefore, other methods of NO{sub x} reduction were considered including utilizing some form of off-stoichiometric, burners out of service (BOOS), firing. It was determined that the stringent emission limits could be met utilizing off-stoichiometric firing techniques. New oil gun atomizer tips allowing off-stoichiometric firing with mechanical atomization and swirlers of a new design are replacing the existing atomizers. The new hardware eliminates the problems of opacity while operating with off-stoichiometric firing.

Paschedag, A.E.; Martinsen, R.A.; O`Sullivan, R.C.; Schmidt, D.W. [and others

1996-01-01T23:59:59.000Z

491

Emissions Reduction Impact of Renewables  

E-Print Network [OSTI]

p. 1 Energy Systems Laboratory ? 2012 EMISSIONS REDUCTION IMPACT OF RENEWABLES October 2012 Jeff Haberl, Bahman Yazdani, Charles Culp Energy Systems Laboratory Texas A&M University p. 2 Energy Systems Laboratory ? 2012... Do TCEQ: Vince Meiller, Bob Gifford ERCOT: Warren Lasher USEPA: Art Diem, Julie Rosenberg ACKNOWLEDGEMENTS p. 3 Energy Systems Laboratory ? 2012 RENEWABLES Solar PV Solar Thermal Hydro Biomass Landfill Gas Geothermal p. 4...

Haberl, J. S.; Yazdani, B.; Culp, C.

2012-01-01T23:59:59.000Z

492

Single crystal oxide and oxide/oxide eutectic fibres for high temperature composites  

Science Journals Connector (OSTI)

The utilisation of fibre-reinforced metal, intermetallic and ceramic matrix composites (CMCs) in gas turbine engines offers the potential of improved fuel efficiency, higher operating temperature and greater thrust to weight ratio. The development of ceramic fibres with high strength, excellent strength retention at elevated temperatures and good creep resistance is essential to the successful implementation of composites in various high temperature components. Several single crystal oxide and oxide/oxide eutectic fibres have been developed to meet the demanding performance requirements. Recent progress made on developing these fibers will be discussed.

J.-M. Yang

2001-01-01T23:59:59.000Z

493

MERCURY OXIDIZATION IN NON-THERMAL PLASMA BARRIER DISCHARGE SYSTEM  

SciTech Connect (OSTI)

In the past decade, the emission of toxic elements from human activities has become a matter of great public concern. Hg, As, Se and Cd typically volatilize during a combustion process and are not easily caught with conventional air pollution control techniques. In addition, there is no pollution prevention technique available now or likely be available in the foreseeable future that can prevent the emission of these trace elements. These trace elements pose additional scientific challenge as they are present at only ppb levels in large gas streams. Mercury, in particular, has attracted significant attention due to its high volatility, toxicity and potential threat to human health. In the present research work, a non-thermal plasma dielectric barrier discharge technique has been used to oxidize Hg{sup 0}(g) to HgO. The basic premise of this approach is that Hg{sup 0} in vapor form cannot be easily removed in an absorption tower whereas HgO as a particulate is amiable to water scrubbing. The work presented in this report consists of three steps: (1) setting-up of an experimental apparatus to generate mercury vapors at a constant rate and modifying the existing non-thermal plasma reactor system, (2) solving the analytical challenge for measuring mercury vapor concentration at ppb level, and (3) conducting experiments on mercury oxidation under plasma conditions to establish proof of concept.

V.K. Mathur

2003-02-01T23:59:59.000Z

494

Influence of operating conditions and coal properties on \\{NOx\\} and N2O emissions in pressurized fluidized bed combustion of subbituminous coals  

Science Journals Connector (OSTI)

This experimental study is aimed at finding effects of operating conditions in PFBC on nitrogen oxide emissions for subbituminous coals differing in ash content/composition, combustion/gasification reactivities and in particle size distribution. The experiments have been done on a smaller laboratory apparatus with ID=8 cm. The effects of operating pressure (0.1–1 MPa), temperature of the fluidized bed (800–900 °C), freeboard temperature and oxygen concentration (3–10 vol.%) on the nitrogen oxides emissions are relatively complex, coupled with temperature of burning coal particles. The coal ash content/composition (esp. CaO and Fe2O3) and fly ash freeboard concentration play an important role in formation/destruction chemistry of both NO and N2O. The \\{NOx\\} emissions decrease with increasing operating pressure at the same volumetric oxygen concentration and temperature. Temperature, volatile content, reactivities of coals and ash composition are the most important factors for N2O emissions. The N2O emissions are either almost constant or can exhibit a maximum at increasing operating pressure. Influence of increasing oxygen concentration on \\{NOx\\} and N2O emissions is more pronounced at lower operating pressures, esp. for the less reactive, medium ash coal. The particle size distribution of the coal (influence of coal dust) can cause characteristic changes in \\{NOx\\} and N2O emissions in PFBC, esp. at lower combustion temperatures (800–840 °C). The emission changes are dependent on ash properties/composition.

Karel Svoboda; Michael Poho?elý

2004-01-01T23:59:59.000Z

495

XX--ray Emission from O Starsray Emission from O Stars David CohenDavid Cohen  

E-Print Network [OSTI]

XX--ray Emission from O Starsray Emission from O Stars David CohenDavid Cohen Swarthmore College windstheir magnetically channeled winds 2.2. After ~1After ~1 MyrMyr XX--ray emission is weaker andray emission is weaker and softer: embedded wind shocks in early Osofter: embedded wind shocks in early O

Cohen, David

496

Global distribution of N2O emissions from aquatic systems: natural emissions and anthropogenic eects  

E-Print Network [OSTI]

Global distribution of N2O emissions from aquatic systems: natural emissions and anthropogenic, are increasing due to human activities. Our analysis suggests that a third of global anthropogenic N2O emission the remainder. Over 80% of aquatic anthropogenic N2O emissions are from the Northern Hemisphere mid

Seitzinger, Sybil

497

High Energy Astrophysics: Emission and Absorption 1/114 Emission and Absorption  

E-Print Network [OSTI]

High Energy Astrophysics: Emission and Absorption 1/114 Emission and Absorption 1 Motivation and the jet. #12;High Energy Astrophysics: Emission and Absorption 2/114 HST optical image of 3C273 Note: Emission and Absorption 3/114 Set of 3 images of the jet of 3C273. Left: HST Middle: Chandra X-ray Right

Bicknell, Geoff

498

Assessment of Health Hazards of Repeated Inhalation of Diesel Emissions, with Comparisons to Other Source Emissions  

Broader source: Energy.gov [DOE]

2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: National Environmental Respiratory Center

499

GLOBAL EMISSIONS Greenhouse gas (GHG) emissions, largely carbon dioxide (CO2)  

E-Print Network [OSTI]

GLOBAL EMISSIONS Greenhouse gas (GHG) emissions, largely carbon dioxide (CO2) from the combustion. Figure 1 Global Carbon Dioxide Emissions: 1850­2030 1850 1860 1870 1880 1890 1900 1910 1920 1930 1940- related CO2 emissions have risen 130-fold since 1850--from 200 million tons to 27 billion tons a year

Green, Donna

500

Black Carbon Emissions by Rocket Engines Types of rocket engines Emissions  

E-Print Network [OSTI]

Black Carbon Emissions by Rocket Engines Types of rocket engines Emissions Liquid Hydrogen. Note: Black carbon does not deplete ozone. What happens is the black carbon emissions from the rocket. Other black carbon emissions: The number one contributor to black carbon is burning biomass. Also

Toohey, Darin W.