Powered by Deep Web Technologies
Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

The impact of manufacturing offshore on technology development paths in the automotive and optoelectronics industries  

E-Print Network (OSTI)

This dissertation presents a two-case study of the impact of manufacturing offshore on the technology trajectory of the firm and the industry. It looks in particular at the automotive and optoelectronics industries. The ...

Fuchs, Erica R. H. (Erica Renee H.), 1977-

2006-01-01T23:59:59.000Z

2

Optoelectronics Industry Development Association  

Science Conference Proceedings (OSTI)

... those systems that meet final demand are information ... One survey found that 45 percent of respondents ... there was a tremendous response from the ...

2010-10-05T23:59:59.000Z

3

Design for Location? The Impact of Manufacturing Offshore on Technology Competitiveness in the Optoelectronics Industry  

Science Conference Proceedings (OSTI)

This paper presents a case study of the impact of manufacturing offshore on technology competitiveness in the optoelectronics industry. It examines a critical design/facility location decision being faced by optoelectronic component manufacturers. This ... Keywords: design for manufacturing, international, product development, technology choice

Erica Fuchs; Randolph Kirchain

2010-12-01T23:59:59.000Z

4

DEVELOPMENT OF HYBRID NANOCRYSTAL/CONDUCTING POLYMER OPTOELECTRONIC DEVICES.  

E-Print Network (OSTI)

??Novel hybrid inorganic nanocrystal/conducting polymer optoelectronic devices have gained extensive interest due to the benefits of ease of processing, low cost, substrate flexibility, large area (more)

Zhu, Ting

2010-01-01T23:59:59.000Z

5

INDUSTRIAL DEVELOPMENT  

E-Print Network (OSTI)

The views expressed in this paper are solely those of the authors. They do not necessarily represent the views of the World Bank or its member countries and should not be attributed to This paper examines the effect of foreign ownership on value added of firms in sub-Saharan Africa, using firm-level data from the Regional Program on Enterprise Development at the World Bank. The econometric analysis shows that foreign ownership has a significant effect on value added only when it exceeds a majority share. The results for Africa are consistent with the existing literature on foreign investment which argues that majority ownership creates appropriate incentives and provides greater opportunity to raise firm-level value added. 1

Vijaya Ramach; Manju Kedia Shah

1998-01-01T23:59:59.000Z

6

Recent developments: Industry briefs  

SciTech Connect

This article is the `Industry Briefs` portion of the March 1992 `Recent Developments` section of Nuexco. Specific issues mentioned are: (1) closure of Yankee Rowe, (2) steam-generator tube plugging at Trojan, (3) laser enrichment in South Africa, (4) the US uranium industry, (5) planning for two nuclear units in Taiwan, and (6) the establishment of a Czech/French joint venture.

NONE

1992-03-01T23:59:59.000Z

7

Recent developments: Industry briefs  

Science Conference Proceedings (OSTI)

This article is the `Industry Briefs` portion of Nuexco`s September 1992 `Recent Developments` section. Specific iems discussed include: (1) merger of Urangesellschaft and Interuran, (2) cessation of uranium mining in Bulgaria, (3) record operation of Limerick-2 and Tokai-2, (4) MRS in Wyoming, (5) low-level waste facilities at Perry, (6) closure of Trojan, (7) restart of Kozloduy-6, (8) agreements between Cogema and Minatom, (9) planning for a large nuclear power plant in Japan moves forward, (10) order of a new reactor at Civaux, (11) relicensing of Yankee Rowe, (12) operation of Bradwell-2, and (13) high-level waste management in Japan.

NONE

1992-09-01T23:59:59.000Z

8

Recent developments: Industry briefs  

Science Conference Proceedings (OSTI)

This article is the `Industry Briefs` portion of Nuexco`s August 2992 `Recent Developments` section. Specific items discussed include: (1) non-proliferation in Argentina and Brazil, (2) a joint-venture uranium leaching project in the USA, (3) life extension for Yankee Rowe, (4) contracts for nuclear plants in the Republic of Korea, (5) cleanup of Wismut, (6) record operation of Three Mile Island-1, Oconee-1, and Cook-1, (7) closure of Kozloduy units, (8) China`s ascension to the non-proliferation treaty, and (9) a centrifuge enrichment facility in Japan.

NONE

1991-08-01T23:59:59.000Z

9

Industrial Development Projects (Montana)  

Energy.gov (U.S. Department of Energy (DOE))

This legislation authorizes municipalities and counties to issue bonds or interest coupons to finance industrial projects, including energy generation facilities.

10

Recent developments: Industry briefs  

SciTech Connect

The January 1992 Industry Briefs includes brief articles on: (1) the startup of Chinese and Indian nuclear units, (2) agreements between China and Pakistan for the construction of a nuclear unit, (3) international safeguards agreements, (4) restart of a nuclear unit in Armenia, (5) closure of a German nuclear waste site, (6) restructuring of the Hungarian state-owned utility MVMT, (7) requests for bids for Wolsong Units 3 and 4, (8) signing of the European Energy charter, (9) continued operation of the MAGNOX reactors, and (10) changing Canadian requirements on uranium.

NONE

1992-01-01T23:59:59.000Z

11

Review: 1991 industry developments  

Science Conference Proceedings (OSTI)

This is NUEXCO`s annual summary of the previous year`s (1991) events. There are reviews of major nuclear developments in each continent, as well as international developments. Specific topics include fuels, waste management, new facilities, and decommissioning. Nuclear activities in the following countries are noted: South Africa, Yemen, Lithuania, Latvia, Estonia, Namibia, France, Japan, Taiwan, China, Korea, India, Pakistan, Federal Republic of Germany, Spain, Hungary, Kazakhstan, Italy, Czechoslovakia, United Kingdom, Switzerland, Canada, USA, Argentina, Brazil, and Uraguay.

NONE

1992-01-01T23:59:59.000Z

12

Alternative Fuels Data Center: Biofuels Industry Development...  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Biofuels Industry Development Grants to someone by E-mail Share Alternative Fuels Data Center: Biofuels Industry Development Grants on Facebook Tweet about Alternative Fuels Data...

13

and Submicron Oxide Powders for Optoelectronic and Renewable ...  

Science Conference Proceedings (OSTI)

Among various materials processes, Umicore develops technologies and manufactures various oxide powders for optoelectronic and renewable energy...

14

Session: Wind industry project development  

DOE Green Energy (OSTI)

This first session at the Wind Energy and Birds/Bats workshop consisted of two presentations followed by a question and answer period. The session was intended to provide a general overview of wind energy product development, from the industry's perspective. Tom Gray of AWEA presented a paper titled ''State of the Wind Energy Industry in 2004'', highlighting improved performance and lower cost, efforts to address avian impacts, a status of wind energy in comparison to other energy-producing sources, and ending on expectations for the near future. Sam Enfield of Atlantic Renewable Energy Corporation presented a paper titled ''Key Factors for Consideration in Wind Plant Siting'', highlighting factors that wind facility developers must consider when choosing a site to build wind turbines and associated structures. Factors covered include wind resources available, ownership and land use patterns, access to transmission lines, accessibility and environmental impacts. The question and answer sum mary included topics related to risk taking, research and development, regulatory requirements, and dealing with utilities.

Gray, Tom; Enfield, Sam

2004-09-01T23:59:59.000Z

15

Optoelectronic fiber webs for imaging applications  

E-Print Network (OSTI)

We demonstrate the use of novel visible and infrared light-sensitive optoelectronic fiber in the development of large scale photodector arrays. Unlike conventional point photodetectors these one-dimensional linear photodectors ...

Arnold, Jerimy Reeves

2005-01-01T23:59:59.000Z

16

Developing Alternative Industrial Materials from Mining Waste  

Science Conference Proceedings (OSTI)

Presentation Title, Developing Alternative Industrial Materials from Mining Waste ... Optimum Condition of Vanadium Recovery from Power Plant Fly-ash with...

17

Local Option- Industrial Facilities and Development Bonds (Utah)  

Energy.gov (U.S. Department of Energy (DOE))

Under the Utah Industrial Facilities and Development Act, counties, municipalities, and state universities in Utah may issue Industrial Revenue Bonds (IRBs) or Industrial Development Bonds (IDBs)...

18

Dan Miller Associate, Industrial and Economic Development  

NLE Websites -- All DOE Office Websites (Extended Search)

Name, Phone, e-mail address Name, Phone, e-mail address Dan Miller Associate, Industrial and Economic Development Dan Miller joined Oak Ridge National Laboratory in January, 2010 as an Associate in Industrial Partnerships and Economic Development. His responsibilities include leading and supporting initiatives in the energy storage portfolio focused on technology commercialization, economic development, and industrial partnerships. He also manages ORNL's relationships with companies involved in the Oak Ridge Science & Technology Park and is actively recruiting additional companies to locate there. Prior to joining ORNL, Dan was a Licensing Associate in Rice University Office of Technology Transfer, where he managed the patent portfolio of the university's physical science technologies.

19

Optoelectronic Mounting Structure  

DOE Patents (OSTI)

An optoelectronic mounting structure is provided that may be used in conjunction with an optical transmitter, receiver or transceiver module. The mounting structure may be a flexible printed circuit board. Thermal vias or heat pipes in the head region may transmit heat from the mounting structure to the heat spreader. The heat spreader may provide mechanical rigidity or stiffness to the heat region. In another embodiment, an electrical contact and ground plane may pass along a surface of the head region so as to provide an electrical contact path to the optoelectronic devices and limit electromagnetic interference. In yet another embodiment, a window may be formed in the head region of the mounting structure so as to provide access to the heat spreader. Optoelectronic devices may be adapted to the heat spreader in such a manner that the devices are accessible through the window in the mounting structure.

Anderson, Gene R. (Albuquerque, NM); Armendariz, Marcelino G. (Albuquerque, NM); Baca, Johnny R. F. (Albuquerque, NM); Bryan, Robert P. (Albuquerque, NM); Carson, Richard F. (Albuquerque, NM); Chu, Dahwey (Albuquerque, NM); Duckett, III, Edwin B. (Albuquerque, NM); McCormick, Frederick B. (Albuquerque, NM); Peterson, David W. (Sandia Park, NM); Peterson, Gary D. (Albuquerque, NM); Reber, Cathleen A. (Corrales, NM); Reysen, Bill H. (Lafayette, CO)

2004-10-05T23:59:59.000Z

20

Applied Optoelectronics | Open Energy Information  

Open Energy Info (EERE)

optical semiconductor devices, packaged optical components, optical subsystems, laser transmitters, and fiber optic transceivers. References Applied Optoelectronics1...

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

NEW DEVELOPMENTS IN THE WELDING INDUSTRY  

SciTech Connect

A brief review is given of some of the developments and problems in the welding industry. These developments and problems are discussed in terms of new and improved welding processes, welding processes for new materials, improved design principles, and the technical education and training programs in this field. (N.W.R.)

Burt, R.G.

1961-10-01T23:59:59.000Z

22

Industrial Development (Indiana) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

(Indiana) (Indiana) Industrial Development (Indiana) < Back Eligibility Agricultural Commercial Construction Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info Start Date 1981 State Indiana Program Type Corporate Tax Incentive Enterprise Zone Provider Indiana Economic Development Corporation An economically distressed county can apply for designation as a community

23

Alternative Fuels Data Center: Biomass and Biofuels Industry Development  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Biomass and Biofuels Biomass and Biofuels Industry Development to someone by E-mail Share Alternative Fuels Data Center: Biomass and Biofuels Industry Development on Facebook Tweet about Alternative Fuels Data Center: Biomass and Biofuels Industry Development on Twitter Bookmark Alternative Fuels Data Center: Biomass and Biofuels Industry Development on Google Bookmark Alternative Fuels Data Center: Biomass and Biofuels Industry Development on Delicious Rank Alternative Fuels Data Center: Biomass and Biofuels Industry Development on Digg Find More places to share Alternative Fuels Data Center: Biomass and Biofuels Industry Development on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Biomass and Biofuels Industry Development

24

Energy Department Develops Tool with Industry to Help Utilities...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Develops Tool with Industry to Help Utilities Strengthen Their Cybersecurity Capabilities Energy Department Develops Tool with Industry to Help Utilities Strengthen Their...

25

Developing an energy efficiency service industry in Shanghai  

E-Print Network (OSTI)

Japanese Association of Energy Service Companies (JAESCO),growth of a viable energy services industry should become anhealthy development of a local energy services industry, the

Lin, Jiang; Goldman, Charles; Levine, Mark; Hopper, Nicole

2004-01-01T23:59:59.000Z

26

Advanced Energy Industries, Inc. SEGIS developments.  

DOE Green Energy (OSTI)

The Solar Energy Grid Integration Systems (SEGIS) initiative is a three-year, three-stage project that includes conceptual design and market analysis (Stage 1), prototype development/testing (Stage 2), and commercialization (Stage 3). Projects focus on system development of solar technologies, expansion of intelligent renewable energy applications, and connecting large-scale photovoltaic (PV) installations into the electric grid. As documented in this report, Advanced Energy Industries, Inc. (AE), its partners, and Sandia National Laboratories (SNL) successfully collaborated to complete the final stage of the SEGIS initiative, which has guided new technology development and development of methodologies for unification of PV and smart-grid technologies. The combined team met all deliverables throughout the three-year program and commercialized a broad set of the developed technologies.

Scharf, Mesa P. (Advanced Energy Industries, Inc., Bend, OR); Bower, Ward Isaac; Mills-Price, Michael A. (Advanced Energy Industries, Inc., Bend, OR); Sena-Henderson, Lisa; David, Carolyn; Akhil, Abbas Ali; Kuszmaul, Scott S.; Gonzalez, Sigifredo

2012-03-01T23:59:59.000Z

27

BridgeLux Inc former eLite Optoelectronics | Open Energy Information  

Open Energy Info (EERE)

BridgeLux Inc former eLite Optoelectronics BridgeLux Inc former eLite Optoelectronics Jump to: navigation, search Name BridgeLux Inc (former eLite Optoelectronics) Place Sunnyvale, California Zip 94086 Product Developer and provider of indium gallium nitride light emitting diodes (InGaN LEDs) for solid state lighting, mobile appliance, signage, and automotive applications. References BridgeLux Inc (former eLite Optoelectronics)[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. BridgeLux Inc (former eLite Optoelectronics) is a company located in Sunnyvale, California . References ↑ "BridgeLux Inc (former eLite Optoelectronics)" Retrieved from "http://en.openei.org/w/index.php?title=BridgeLux_Inc_former_eLite_Optoelectronics&oldid=34303

28

Industrial Energy Efficiency Programs: Development and Trends  

E-Print Network (OSTI)

As more states establish Energy Efficiency Resource Standards (EERS), goals for energy efficiency savings are increasing across the country. Increasingly, states are relying on their industrial energy efficiency programs to find and help implement those savings. Historically, industrial energy efficiency programs have not been completely effective at finding those savings, in large part because the programs have not been flexible enough to accommodate the heterogeneous needs and unique characteristics of the industrial sector. This paper will discuss the state of industrial energy efficiency programs today. Relying on an ACEEE-administered survey of 35 industrial energy efficiency programs, we will determine current trends and challenges, address emerging needs, and identify best practices in the administration of today's industrial efficiency programs. The paper will serve as an update on industrial energy efficiency program activities and discuss the ways in which today's programs are trying to serve their industrial clients better.

Chittum, A.; Kaufman, N.; Elliot, N.

2010-01-01T23:59:59.000Z

29

Local Option - Industrial Facilities and Development Bonds |...  

Open Energy Info (EERE)

Sector Commercial, Industrial, Institutional, Local Government Eligible Technologies Boilers, Building Insulation, CaulkingWeather-stripping, Central Air conditioners, Chillers,...

30

Development of a Performance-based Industrial Energy Efficiency...  

NLE Websites -- All DOE Office Websites (Extended Search)

the work of EPA and the pharmaceutical manufacturing industry to develop an Energy Performance Indicator (EPI) for facilities that develop and manufacture pharmaceutical products...

31

Pages that link to "Baoding High Tech Industry Development Zone...  

Open Energy Info (EERE)

Zone. Retrieved from "http:en.openei.orgwikiSpecial:WhatLinksHereBaodingHighTechIndustryDevelopmentZone" Special pages About us Disclaimers Energy blogs Developer...

32

Establishing Ergonomics in Industrially Developing Countries  

SciTech Connect

The introduction of ergonomics is an ongoing effort in industrially developing countries and will ultimately require an organized, programmatic approach spanning several countries and organizations. Our preliminary efforts with our partner countries of Viet Nam, Thailand, and Nicaragua have demonstrated that a one-time course is just the first step in a series of necessary events to provide skills and create an infrastructure that will have lasting impact for the host country. To facilitate that any sort of training has a lasting impact, it is recommended that host countries establish a 'contract' with class participants and the guest instructors for at least one follow-up visit so instructors can see the progress and support the participants in current and future efforts. With repeated exchanges, the class participants can become the 'in country experts' and the next generation of ergonomic trainers. Additionally, providing participants with an easy to use hazard assessment tool and methods for evaluating the financial impact of the project (cost/benefit analysis) will assist increase the likelihood of success and establish a foundation for future projects. In the future, developing trade and regionally/culturally specific 'ergonomics toolkits' can help promote broader implementation, especially where training resources may be limited.

Stewart, K; Silverstein, B; Kiefer, M

2005-08-29T23:59:59.000Z

33

Designing Success - Industrial Process Interface Development.  

E-Print Network (OSTI)

??This master thesis describes and treats the conflict between usability and safety in designing industrial interfaces. With literature studies and case studies as a base (more)

Persson, Markus

2004-01-01T23:59:59.000Z

34

Jeff Cornett Manager, Industrial and Economic Development  

NLE Websites -- All DOE Office Websites (Extended Search)

and numerous chemical industry clients such as chemical manufacturers, oil & gas refineries, paper product manufacturers, and special material manufacturers assisting them with...

35

United Nations Industrial Development Organization (UNIDO) |...  

Open Energy Info (EERE)

1.2 UNIDO Programs 2 References Resources UNIDO Tools A Global Technology Roadmap on Carbon Capture and Storage in Industry COMFAR III: Computer Model for Feasibility Analysis...

36

Development of alternate parts for the aerospace industry  

E-Print Network (OSTI)

This thesis explores the topic of the development of alternate parts for the aerospace industry, drawing on industry examples to demonstrate methods and approaches and the benefits to firms engaged in these activities. I ...

Tapley, James Paul

2010-01-01T23:59:59.000Z

37

Capital project development in biotechnology industry  

E-Print Network (OSTI)

The biotechnology industry has experienced fast growth during the first 30 years of its existence but is now reaching a stage of maturity. Companies are being challenged by weak pipelines and patent expirations, as well ...

Kristinsdottir, Asbjorg

2008-01-01T23:59:59.000Z

38

Developing a solar energy industry in Egypt  

E-Print Network (OSTI)

This paper assesses Egypt's current energy infrastructure and its problems, the available solar energy resource, and the technologies required to harness this resource. After this assessment, an industry based on high ...

AbdelMessih, Sherife (Sherife Mohsen)

2009-01-01T23:59:59.000Z

39

Industrial Lighting Techniques and New Developments  

E-Print Network (OSTI)

The energy crisis of the early seventies has had a drastic influence on both the application and development of light sources. This situation has forced us to examine old methods and search for new answers for improved efficiency. We can no longer operate on the premise that more is better. At lower light levels a lighting design is less forgiving. The current thrust in lamp and luminare design has been high efficiency. Tremendous effort has been expended to produce energy efficient sources that deliver better color, improved optical control, and reduced lamp size. Given that we must operate in this arena of heightened energy awareness and that lighting, by its very nature, becomes a prime candidate for reduction, we must not lose sight of the fundamental reason for lighting to provide the ability for us to see details to perform specific tasks. The heart of an industrial plant is the production area. A myriad of tasks must be accomplished. Lighting is installed for humans, not machines. The eye can only adapt to a degree and accommodate a variety of conditions; i.e., color, texture, etc. Higher light levels are required as an individuals age increases. It has also been confirmed in many studies that light levels directly affect performance. People who have sufficient quantity and quality of illumination can accomplish their work faster and more accurately. A delicate balance lies between energy efficient lighting and under and over-lit spaces. This balance is with the fundamental lighting goal. Any formula to maintain this balance should include two vital factors: First, light output for levels and quality determined by proper task analysis and second, control by design which utilizes the best source and equipment available.

Colotti, M. A.

1985-05-01T23:59:59.000Z

40

Industry Supply Chain Development (Ohio) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Industry Supply Chain Development (Ohio) Industry Supply Chain Development (Ohio) Industry Supply Chain Development (Ohio) < Back Eligibility Utility Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Installer/Contractor Rural Electric Cooperative Retail Supplier Systems Integrator Fuel Distributor Transportation Savings Category Solar Buying & Making Electricity Wind Program Info State Ohio Program Type Grant Program Industry Recruitment/Support Loan Program Provider Ohio Development Services Agency Supply Chain Development programs are focused on targeted industries that have significant growth opportunities for Ohio's existing manufacturing sector from emerging energy resources and technologies. The Office of Energy is currently working on developing the supply chains for the wind,

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Policies for Promoting Industrial Energy Efficiency in Developing Countries  

Open Energy Info (EERE)

Policies for Promoting Industrial Energy Efficiency in Developing Countries Policies for Promoting Industrial Energy Efficiency in Developing Countries and Transition Economies Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Policies for Promoting Industrial Energy Efficiency in Developing Countries and Transition Economies Focus Area: Industry Topics: Policy Data Website: www.unido.org/fileadmin/media/documents/pdf/Energy_Environment/ind_ene Equivalent URI: cleanenergysolutions.org/content/policies-promoting-industrial-energy- Language: English Policies: "Deployment Programs,Regulations" is not in the list of possible values (Deployment Programs, Financial Incentives, Regulations) for this property. DeploymentPrograms: Industry Codes & Standards Regulations: Energy Standards This paper presents policy options under the structure of an Industrial

42

Development of a Performance-based Industrial Energy Efficiency...  

NLE Websites -- All DOE Office Websites (Extended Search)

the work of EPA and the automobile manufacturing industry to develop an Energy Performance Indicator (EPI) for assembly plants. These types of plants are defined as those that...

43

Policies for Promoting Industrial Energy Efficiency in Developing...  

Open Energy Info (EERE)

Jump to: navigation, search Name Policies for Promoting Industrial Energy Efficiency in Developing Countries and Transition Economies Abstract This paper presents policy options...

44

Baoding High Tech Industry Development Zone | Open Energy Information  

Open Energy Info (EERE)

Zone" Retrieved from "http:en.openei.orgwindex.php?titleBaodingHighTechIndustryDevelopmentZone&oldid342524" Categories: Clean Energy Organizations Companies...

45

The development of coke smelting and the industrial revolution  

E-Print Network (OSTI)

Abraham Darby and the origins of the industrial revolution in Britain. Alan Macfarlane talks to John about the reasons for the area near Birmingham becoming the epi-centre of the industrial development, and the development of coke furnaces and iron...

Macfarlane, Alan

2004-08-05T23:59:59.000Z

46

Development of a Performance-based Industrial Energy Efficiency Indicator  

NLE Websites -- All DOE Office Websites (Extended Search)

Development of a Performance-based Industrial Energy Efficiency Development of a Performance-based Industrial Energy Efficiency Indicator for Food Processing Plants Secondary menu About us Press room Contact Us Portfolio Manager Login Facility owners and managers Existing buildings Commercial new construction Industrial energy management Small business Service providers Service and product providers Verify applications for ENERGY STAR certification Design commercial buildings Energy efficiency program administrators Commercial and industrial program sponsors Associations State and local governments Federal agencies Tools and resources Training In This Section Campaigns Commercial building design Communications resources Energy management guidance Financial resources Portfolio Manager Products and purchasing Recognition Research and reports

47

Current developments of microfiltration technology in the dairy industry  

E-Print Network (OSTI)

Review Current developments of microfiltration technology in the dairy industry Luciana V. SABOYAa of them just patented, in the dairy industry. Combination of the use of uniform trans- membrane hydraulic porosity gradient and of new ceramic membrane materials allows nowa- days to get a differential separation

Recanati, Catherine

48

Hydrothermal industrialization: direct heat development. Final report  

Science Conference Proceedings (OSTI)

A description of hydrothermal resources suitable for direct applications, their associated temperatures, geographic distribution and developable capacity are given. An overview of the hydrothermal direct-heat development infrastructure is presented. Development activity is highlighted by examining known and planned geothermal direct-use applications. Underlying assumptions and results for three studies conducted to determine direct-use market penetration of geothermal energy are discussed.

Not Available

1982-05-01T23:59:59.000Z

49

Optoelectronic inventory system for special nuclear material  

SciTech Connect

In support of the Department of Energy`s Dismantlement Program, the Optoelectronics Characterization and Sensor Development Department 2231 at Sandia National Laboratories/New Mexico has developed an in situ nonintrusive Optoelectronic Inventory System (OIS) that has the potential for application wherever periodic inventory of selected material is desired. Using a network of fiber-optic links, the OIS retrieves and stores inventory signatures from data storage devices (which are permanently attached to material storage containers) while inherently providing electromagnetic pulse immunity and electrical noise isolation. Photovoltaic cells (located within the storage facility) convert laser diode optic power from a laser driver to electrical energy. When powered and triggered, the data storage devices sequentially output their digital inventory signatures through light-emitting diode/photo diode data links for retrieval and storage in a mobile data acquisition system. An item`s exact location is determined through fiber-optic network and software design. The OIS provides an on-demand method for obtaining acceptable inventory reports while eliminating the need for human presence inside the material storage facility. By using modularization and prefabricated construction with mature technologies and components, an OIS installation with virtually unlimited capacity can be tailored to the customer`s requirements.

Sieradzki, F.H.

1994-01-01T23:59:59.000Z

50

An overview of industry-military cooperation in the development...  

Open Energy Info (EERE)

navigation, search OpenEI Reference LibraryAdd to library Journal Article: An overview of industry-military cooperation in the development of power operations at the Coso...

51

United Nations Industrial Development Organization (UNIDO) | Open Energy  

Open Energy Info (EERE)

United Nations Industrial Development Organization (UNIDO) United Nations Industrial Development Organization (UNIDO) Jump to: navigation, search Logo: United Nations Industrial Development Organization Name United Nations Industrial Development Organization Address Wagramer Straße 5, 1220 Place Vienna, Austria Phone number +43 (1) 26026-0 Coordinates 48.2336891°, 16.4174512° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":48.2336891,"lon":16.4174512,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

52

United Nations Industrial Development Organization (UNIDO) | Open Energy  

Open Energy Info (EERE)

Industrial Development Organization (UNIDO) Industrial Development Organization (UNIDO) (Redirected from UNIDO) Jump to: navigation, search Logo: United Nations Industrial Development Organization Name United Nations Industrial Development Organization Address Wagramer Straße 5, 1220 Place Vienna, Austria Phone number +43 (1) 26026-0 Coordinates 48.2336891°, 16.4174512° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":48.2336891,"lon":16.4174512,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

53

Industrial Development Fund (North Carolina) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fund (North Carolina) Fund (North Carolina) Industrial Development Fund (North Carolina) < Back Eligibility Commercial Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State North Carolina Program Type Grant Program Loan Program Provider Department of Commerce The Industrial Development Fund provides financing grants and loans through designated municipalities and counties to assist in infrastructure improvements for targeted industrial projects. The local government reserves the funds and proposed projects are eligible for grants, but the local government must match the state funding 3:1. Project owners must demonstrate a commitment to generating jobs and present a business plan.

54

Industrial Energy Use and Energy Efficiency in Developing Countries  

E-Print Network (OSTI)

The industrial sector accounts for over 50% of energy used in developing countries. Growth in this sector has been over 4.5% per year since 1980. Energy intensity trends for four energy-intensive sub-sectors (iron and steel, chemicals, building materials, and pulp and paper) are reviewed. Scenarios of future industrial sector energy use in developing countries show that this region will dominate world industrial energy use in 2020. Growth is expected to be about 3.0% per year in a business-as-usual case, but can be reduced using state-of-the art or advanced technologies. Polices to encourage adoption of these technologies are briefly discussed.

Price, L.; Martin, N.; Levine, M. D.; Worrell, E.

1996-04-01T23:59:59.000Z

55

Industrial Plant Objectives and Cogeneration System Development  

E-Print Network (OSTI)

The development of a cogeneration system requires a definition of plant management's objectives in addition to process energy demands. And, these objectives may not be compatible with options that will yield the most attractive rate of return. This paper will review cogeneration system application criteria and illustrate how plant objectives can influence the cogeneration system selection.

Kovacik, J. M.

1983-01-01T23:59:59.000Z

56

Global product development in semiconductor industry : Intel -- Tick-Tock product development cadence  

E-Print Network (OSTI)

This thesis investigates on changes in semiconductor industry's product development methodology by following Intel's product development from year 2000. Intel was challenged by customer's preference change, competitors new ...

Park, Cheolmin, S.M. Massachusetts Institute of Technology

2008-01-01T23:59:59.000Z

57

Industry  

E-Print Network (OSTI)

from refrigeration equipment used in industrial processesfrom refrigeration equipment used in industrial processesfrom refrigeration equipment used in industrial processes

Bernstein, Lenny

2008-01-01T23:59:59.000Z

58

Environmental technology development through industry partnership  

Science Conference Proceedings (OSTI)

The Coherent Laser Vision System (CLVS) is being developed to provide precision real-time 3D world views to support site characterization and robotic operations and during facilities Decontamination and Decommissioning. Autonomous or semiautonomous robotic operations requires an accurate, up-to-date 3D world view. Existing technologies for real-time 3D imaging, such as AM laser radar, have limited accuracy at significant ranges and have variability in range estimates caused by lighting or surface shading. Recent advances in fiber optic component technology and digital processing components have enabled the development of a new 3D vision system based upon a fiber optic FMCW coherent laser radar. The approach includes a compact scanner with no-moving parts capable of randomly addressing all pixels. The system maintains the immunity to lighting and surface shading conditions which is characteristic to coherent laser radar. The random pixel addressability allows concentration of scanning and processing on the active areas of a scene, as is done by the human eye-brain system. The precision measurement capability of the coherent laser radar (CLR) technology has already been demonstrated in the form of the CLR 3D Mapper, of which several copies have been delivered or are under order. The CLVS system, in contrast to the CLR 3D Mapper, will have substantially greater imaging speed with a compact no-moving parts scanner, more suitable for real-time robotic operations.

Sebastion, R.L.

1995-12-31T23:59:59.000Z

59

DOE Announces Additional Steps in Developing Sustainable Biofuels Industry  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Steps in Developing Sustainable Biofuels Steps in Developing Sustainable Biofuels Industry DOE Announces Additional Steps in Developing Sustainable Biofuels Industry October 7, 2008 - 4:14pm Addthis Releases Results from Preliminary Intermediate Blends Report, Continues Commitment of Commercial Scale Biorefinery, Announces $7 Million for New Biofuels Projects WASHINGTON - Secretary of Energy Samuel W. Bodman and Secretary of Agriculture Ed Schafer today released the National Biofuels Action Plan (NBAP). The Plan, developed by an interagency board co-chaired by DOE and USDA, outlines specific action areas and goals toward achieving renewable fuels production targets. Secretary Bodman also announced additional steps the U.S. Department of Energy (DOE) is taking to support the development of a sustainable biofuels industry: research to enable

60

Commercial/industrial applications spur solar development  

SciTech Connect

Several large commercial buildings with solar systems are examined. The first building mentioned is the La Quinta Motor Inn located in Dallas, Texas. The system supplies approximately 90% of the hot water for the rooms and laundry. The largest solar cooling system is located in Frenchman's Reef, the Holiday Inn, St. Thomas, Virgin Islands. The system was funded by a 75% grant from the Energy Research and Development Administration. In Decatur, Alabama, construction has begun on a solar heating system that will be used at a large soybean oil extraction facility. The project is also sponsored in part by ERDA. The solar panels will be used to air dry the soy beans. The largest solar-powered irrigation system is located in Gila River Ranch southwest of Phoenix, Arizona. The system includes a 50-hp pump capable of delivering up to 10,000 gallons of irrigation water per minute. It operates with 5,500 ft/sup 2/ of parabolic tracking collectors.

Comstock, W.S.

1977-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Energy Department Develops Tool with Industry to Help Utilities Strengthen  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Develops Tool with Industry to Help Utilities Develops Tool with Industry to Help Utilities Strengthen Their Cybersecurity Capabilities Energy Department Develops Tool with Industry to Help Utilities Strengthen Their Cybersecurity Capabilities June 28, 2012 - 10:24am Addthis News Media Contact (202) 586-4940 WASHINGTON -- As part of the Obama Administration's commitment to protecting America's critical energy infrastructure, U.S. Energy Secretary Steven Chu today announced the release of a new Cybersecurity Self-Evaluation Survey Tool for utilities that will strengthen protection of the nation's electric grid from cybersecurity threats. Today's announcement is part of a broader White House initiative to develop a Cybersecurity Capability Maturity Model for the electricity sector, which aims to support the private sector and utilities nationwide in determining

62

Industry  

Science Conference Proceedings (OSTI)

This chapter addresses past, ongoing, and short (to 2010) and medium-term (to 2030) future actions that can be taken to mitigate GHG emissions from the manufacturing and process industries. Globally, and in most countries, CO{sub 2} accounts for more than 90% of CO{sub 2}-eq GHG emissions from the industrial sector (Price et al., 2006; US EPA, 2006b). These CO{sub 2} emissions arise from three sources: (1) the use of fossil fuels for energy, either directly by industry for heat and power generation or indirectly in the generation of purchased electricity and steam; (2) non-energy uses of fossil fuels in chemical processing and metal smelting; and (3) non-fossil fuel sources, for example cement and lime manufacture. Industrial processes also emit other GHGs, e.g.: (1) Nitrous oxide (N{sub 2}O) is emitted as a byproduct of adipic acid, nitric acid and caprolactam production; (2) HFC-23 is emitted as a byproduct of HCFC-22 production, a refrigerant, and also used in fluoroplastics manufacture; (3) Perfluorocarbons (PFCs) are emitted as byproducts of aluminium smelting and in semiconductor manufacture; (4) Sulphur hexafluoride (SF{sub 6}) is emitted in the manufacture, use and, decommissioning of gas insulated electrical switchgear, during the production of flat screen panels and semiconductors, from magnesium die casting and other industrial applications; (5) Methane (CH{sub 4}) is emitted as a byproduct of some chemical processes; and (6) CH{sub 4} and N{sub 2}O can be emitted by food industry waste streams. Many GHG emission mitigation options have been developed for the industrial sector. They fall into three categories: operating procedures, sector-wide technologies and process-specific technologies. A sampling of these options is discussed in Sections 7.2-7.4. The short- and medium-term potential for and cost of all classes of options are discussed in Section 7.5, barriers to the application of these options are addressed in Section 7.6 and the implication of industrial mitigation for sustainable development is discussed in Section 7.7. Section 7.8 discusses the sector's vulnerability to climate change and options for adaptation. A number of policies have been designed either to encourage voluntary GHG emission reductions from the industrial sector or to mandate such reductions. Section 7.9 describes these policies and the experience gained to date. Co-benefits of reducing GHG emissions from the industrial sector are discussed in Section 7.10. Development of new technology is key to the cost-effective control of industrial GHG emissions. Section 7.11 discusses research, development, deployment and diffusion in the industrial sector and Section 7.12, the long-term (post-2030) technologies for GHG emissions reduction from the industrial sector. Section 7.13 summarizes gaps in knowledge.

Bernstein, Lenny; Roy, Joyashree; Delhotal, K. Casey; Harnisch, Jochen; Matsuhashi, Ryuji; Price, Lynn; Tanaka, Kanako; Worrell, Ernst; Yamba, Francis; Fengqi, Zhou; de la Rue du Can, Stephane; Gielen, Dolf; Joosen, Suzanne; Konar, Manaswita; Matysek, Anna; Miner, Reid; Okazaki, Teruo; Sanders, Johan; Sheinbaum Parado, Claudia

2007-12-01T23:59:59.000Z

63

Industrial hygiene concerns associated with oil shale development  

SciTech Connect

Health protection concerns (including industrial hygiene, safety, and occupational medicine) must be evaluated to insure that development of the oil shale industry proceeds without significant risk to the health of the workers involved. These concerns need to be identified in the early stages of developing this industry. To provide a basis for discussing potential health protection concerns related to oil shale, it is necessary to briefly discuss the magnitude and characteristics of this resource; the alternate proposed technologies; and the unit operations which make up the operating system. This subject has been detailed in many publications, among them reports prepared for the Environmental Protection Agency. This discussion will be limited to providing sufficient background to put industrial hygiene and other health protection concerns in perspective, and will include a brief description of typical technologies under consideration. It will not provide a detailed description of these technologies, or attempt to cover all the alternate technologies which may be applied to the development of oil shale. However, a basis for considering potential health protection problems associated with development of this industry will be established.

Ettinger, H.J.

1980-01-01T23:59:59.000Z

64

Hydrothermal industrialization electric-power systems development. Final report  

DOE Green Energy (OSTI)

The nature of hydrothermal resources, their associated temperatures, geographic locations, and developable capacity are described. The parties involved in development, required activities and phases of development, regulatory and permitting requirements, environmental considerations, and time required to complete development activities ae examined in detail. These activities are put in proper perspective by detailing development costs. A profile of the geothermal industry is presented by detailing the participants and their operating characteristics. The current development status of geothermal energy in the US is detailed. The work on market penetration is summarized briefly. Detailed development information is presented for 56 high temperature sites. (MHR)

Not Available

1982-03-01T23:59:59.000Z

65

The Development of Methanol Industry and Methanol Fuel in China  

Science Conference Proceedings (OSTI)

In 2007, China firmly established itself as the driver of the global methanol industry. The country became the world's largest methanol producer and consumer. The development of the methanol industry and methanol fuel in China is reviewed in this article. China is rich in coal but is short on oil and natural gas; unfortunately, transportation development will need more and more oil to provide the fuel. Methanol is becoming a dominant alternative fuel. China is showing the rest of the world how cleaner transportation fuels can be made from coal.

Li, W.Y.; Li, Z.; Xie, K.C. [Taiyuan University of Technology, Taiyuan (China)

2009-07-01T23:59:59.000Z

66

Industry  

E-Print Network (OSTI)

oxide emission reductions in industry in the EU. Europeanissues: Annual survey of industries. Central StatisticalDesiccated coconut industry of Sri- Lankas opportunities

Bernstein, Lenny

2008-01-01T23:59:59.000Z

67

Market development directory for solar industrial process heat systems  

DOE Green Energy (OSTI)

The purpose of this directory is to provide a basis for market development activities through a location listing of key trade associations, trade periodicals, and key firms for three target groups. Potential industrial users and potential IPH system designers were identified as the prime targets for market development activities. The bulk of the directory is a listing of these two groups. The third group, solar IPH equipment manufacturers, was included to provide an information source for potential industrial users and potential IPH system designers. Trade associates and their publications are listed for selected four-digit Standard Industrial Code (SIC) industries. Since industries requiring relatively lower temperature process heat probably will comprise most of the near-term market for solar IPH systems, the 80 SIC's included in this chapter have process temperature requirements less than 350/sup 0/F. Some key statistics and a location list of the largest plants (according to number of employees) in each state are included for 15 of the 80 SIC's. Architectural/engineering and consulting firms are listed which are known to have solar experience. Professional associated and periodicals to which information on solar IPH sytstems may be directed also are included. Solar equipment manufacturers and their associations are listed. The listing is based on the SERI Solar Energy Information Data Base (SEIDB).

None

1980-02-01T23:59:59.000Z

68

Industrial pollution prevention programs in selected developing Asian countries  

SciTech Connect

This paper presents the information on current activities to promote industrial pollution prevention (P2) in five selected Asian economies including Hong Kong, Republic of Korea, the Philippines, ROC in Taiwan, and Thailand. These activities, generally initiated in the last 5 years, are classified into 6 categories: awareness promotion, education and training, information transfer, technology development an demonstration, technical assistance, and financial incentives. Although participation is voluntary, these programs are all important at the early stages of P2 promotion and should be useful in informing industries of the benefit of P2 and helping them identify specific P2 measures as viable environmental management alternatives.

Chiu, Shen-yann [Argonne National Lab., IL (United States)]|[East-West Center, Honolulu, HI (United States)

1995-12-31T23:59:59.000Z

69

The Analysis and Development of Large Industrial Steam Systems  

E-Print Network (OSTI)

Chemicals, petroleum, pulp and paper, and many other industries depend heavily on extensive complex steam systems for thermal and mechanical energy delivery. Steam's versatility and desirable characteristics as both a heat transfer medium and a working fluid has fostered and perpetuated this dependency throughout industrial history. Many large process operations, however, have not developed their steam systems to keep pace with rapidly changing energy economics. As a result, the use of steam on industrial plants seldom approaches the optimum levels of first or second law efficiency. At each of many industrial complexes today, tens of millions of energy dollars per year are literally wasted. This paper describes some case histories comparing actual and optimum steam system configurations, and operational concepts. Highly effective steam system analytical techniques developed and used by the author are discussed. These include "energy level" mass balancing; the "three-branch" thermodynamic system; and powerful sophisticated digital computer steam system models. These latter are really "working models" on which development options can be tried and actively evaluated for economic and technical feasibility. The principal of steam as a plant-wide integrating energy system is explained and demonstrated with examples. These show how a properly structured and effectively operated steam system can increase operational flexibility and facilitate the practical implementation of many energy conservation opportunities in process and plant service areas.

Waterland, A. F.

1980-01-01T23:59:59.000Z

70

Developing an energy efficiency service industry in Shanghai  

E-Print Network (OSTI)

Workshop on Energy Efficiency Service Industry, Shanghai,Workshop on Energy Efficiency Service Industry, Shanghai,Workshop on Energy Efficiency Service Industry, Shanghai,

Lin, Jiang; Goldman, Charles; Levine, Mark; Hopper, Nicole

2004-01-01T23:59:59.000Z

71

Environmental quality indexing of large industrial development alternatives using AHP  

Science Conference Proceedings (OSTI)

Two industrial development alternatives have been proposed for the East Coast of Iceland in order to strengthen its socio-economic basis. The favoured option is to build a large aluminium smelter, which requires massive hydropower development in the nearby highlands. Another viable option is the construction of a 6-million-ton oil refinery, following the planned exploitation of the Timan Pechora oil reserves in the Russian Arctic. A third 'fictitious' alternative could be general development of existing regional industry and new knowledge-based industries, development of ecotourism, establishment of national parks, accompanied by infrastructure improvement (roads, tunnels, communications, schools, etc.). The three alternatives will have different environmental consequences. The controversial hydropower plant for the smelter requires a large water reservoir as well as considerable land disturbance in this unique mountain territory, considered to be the largest uninhabited wilderness in Western Europe. The aluminium smelter and the oil refinery will give rise to substantial increase of the greenhouse gas (GHG) emissions of the country (about 20%). Then there is potential environmental risk associated with the refinery regarding oil spills at sea, which could have disastrous impact on the fisheries industry. However, the oil refinery does not require any hydropower development, which is a positive factor. Finally, the third alternative could be defined as a ''green'' solution whereby the detrimental environmental consequences of the two industrial solutions are mostly avoided. In order to compare the three alternatives in an orderly manner, the analytic hierarchy process methodology of Saaty was applied to calculate the environmental quality index of each alternative, which is defined as a weighted sum of selected environmental and socio-economic factors. These factors are evaluated on a comparison basis, applying the AHP methodology, and the weights in the quality index summation are estimated in the same manner. Six persons with different backgrounds were asked to fill in the comparison matrices in order to reduce bias in the evaluation. The final results show that the two industrial alternatives come out poorly, i.e. with low quality indices, whereas the third pseudo-alternative, i.e. general development, with a considerably higher quality index, is certainly worth a further study.

Solnes, Julius

2003-05-01T23:59:59.000Z

72

Industry  

E-Print Network (OSTI)

the paper, glass or ceramics industry) making it difficulttechnology in the ceramic manufacturing industry. industries: iron and steel, non-ferrous metals, chemicals (including fertilisers), petroleum refining, minerals (cement, lime, glass and ceramics) and

Bernstein, Lenny

2008-01-01T23:59:59.000Z

73

Industry  

E-Print Network (OSTI)

in the iron and steel industry: a global model. Energy, 30,report of the world steel industry 2005. International Irontrends in the iron and steel industry. Energy Policy, 30,

Bernstein, Lenny

2008-01-01T23:59:59.000Z

74

Workforce Development: A Survey of Industry Needs and Training Approaches  

DOE Green Energy (OSTI)

This paper presents information and data collected during 2008 on PV workforce needs by the Interstate Renewable Energy Council for the U.S. Department of Energy. The data was collected from licensed contractors, PV practitioners, educators and expert instructors at training sessions, and at focus group and advisory committee meetings. Respondents were primarily from three states: Florida, New York and California. Other states were represented, but to a lesser extent. For data collection, a 12-item questionnaire was developed that addressed key workforce development issues from the perspectives of both the PV industry and training institutions. A total of 63 responses were collected, although not every respondent answered every question. Industry representatives slightly outnumbered the educators, although the difference in responses was not significant.

Ventre, Jerry; Weissman, Jane

2009-04-01T23:59:59.000Z

75

Supporting R&D of industrial fuel cell developers.  

DOE Green Energy (OSTI)

Argonne National Laboratory is supporting the industrial developers of molten carbonate fuel cells (MCFCs) and tubular solid oxide fuel cells (SOFCs). The results suggest that a lithium concentration level of 65-75 mol% in the LiNa electrolyte will improve cell performance. They have made inroads in understanding the interfacial resistance of bipolar plate materials, and they have reduced the air electrode overpotential in OSFCs by adding dopants.

Krumpelt, M.

1998-09-11T23:59:59.000Z

76

Program on Technology Innovation: Industrial Electrotechnology Development Opportunities  

Science Conference Proceedings (OSTI)

With the industrial sector accounting for about one-third of all energy consumed, continued development of new electrotechnologies will result in improved energy utilization, gross domestic product (GDP) growth, and job creation in this sector. Customers need to be made aware of the operational benefits of energy-efficient technologies, including improved process throughput and quality, reduced energy costs, ease of environmental compliance, enhanced productivity, and greater profits. Utilities can help ...

2009-07-09T23:59:59.000Z

77

Organic LEDs for optoelectronic neural networks  

E-Print Network (OSTI)

In this thesis, I investigate the characteristics of Organic Light Emitting Diodes (OLEDs) and assess their suitability for use in the Compact Optoelectronic Integrated Neural (COIN) coprocessor. The COIN coprocessor, a ...

Mars, Risha R

2012-01-01T23:59:59.000Z

78

US energy industry financial developments, 1993 first quarter  

Science Conference Proceedings (OSTI)

Net income for 259 energy companies-- including, 20 major US petroleum companies-- rose 38 percent between the first quarter of 1992 and the first quarter of 1993. An increased level of economic activity, along with colder weather, helped lift the demand for natural gas. crude oil, coal, and electricity. The sharp rise in the domestic price of natural gas at the wellhead relative to the year-ago quarter was the most significant development in US energy during the first quarter. As a consequence of higher natural gas prices, the upstream segment of the petroleum industry reported large gains in income, while downstream income rose due to higher refined product demand. Increased economic activity and higher weather-related natural gas demand also led to improvements in income for the rate-regulated energy segment. However, declining domestic oil production continued to restrain upstream petroleum industry earnings growth, despite a moderate rise in crude oil prices.

Not Available

1993-06-25T23:59:59.000Z

79

Licensing arrangements and the development of the solar energy industry  

SciTech Connect

The process by which technology and information related to technology are transferred within industry is explored. Property rights in technology are part of the broader field of intellectual property. The general contours of legal protection for knowledge are explored. The four basic forms of intellectual property - patents, trade secrets (or know-how), trademarks, and copyrights - are covered in varying degrees of depth, depending on their relative applicability to the development of the solar industry. Once this background has been established, the legal aspects of licensing are examined. A license is a legal arrangement whereby a party (licensor) who controls the right to use an idea, invention, etc. shares the right to use the particular intellectual property with someone else (licensee). The advantages and disadvantages of licensing are described from the point of view of potential licensees and licensors. Barriers to licensing are discussed.

Green, M.

1979-06-01T23:59:59.000Z

80

Estimating energy-augmenting technological change in developing country industries  

E-Print Network (OSTI)

trend due to the constant energy price bias assumption. ThisIndian industries, Energy price bias (standard error)industries, 19801997 Energy price bias (standard error)

Sanstad, Alan H.; Roy, Joyashree; Sathaye, Jayant A.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Industry  

E-Print Network (OSTI)

and power in US industry. Energy Policy, 29, pp. 1243-1254.Paris. IEA, 2004: Energy Policies of IEA Countries: Finlandand steel industry. Energy Policy, 30, pp. 827-838. Kim, Y.

Bernstein, Lenny

2008-01-01T23:59:59.000Z

82

Conference 5739, SPIE International Symposium Integrated Optoelectronic Devices, 22-27 Jan 2005, San Jose, CA Development of high power green light emitting diode dies in  

E-Print Network (OSTI)

, San Jose, CA Development of high power green light emitting diode dies in piezoelectric Ga in green light emitting diodes is one of the big challenges towards all-solid- state lighting. The prime,3], and commercialization [4,5] of high brightness light emitting diodes LEDs has led to a 1.82 Billion-$/year world market

Wetzel, Christian M.

83

Development of a process control sensor for the glass industry  

SciTech Connect

This project was initiated to fill a need in the glass industry for a non-contact temperature sensor for glass melts. At present, the glass forming industry (e.g., bottle manufacture) consumes significant amounts of energy. Careful control of temperature at the point the bottle is molded is necessary to prevent the bottle from being rejected as out-of-specification. In general, the entire glass melting and conditioning process is designed to minimize this rejection rate, maximize throughput and thus control energy and production costs. This program focuses on the design, development and testing of an advanced optically based pyrometer for glass melts. The pyrometer operates simultaneously at four wavelengths; through analytical treatment of the signals, internal temperature profiles within the glass melt can be resolved. A novel multiplexer alloys optical signals from a large number of fiber-optic sensors to be collected and resolved by a single detector at a location remote from the process. This results in a significant cost savings on a per measurement point basis. The development program is divided into two phases. Phase 1 involves the construction of a breadboard version on the instrument and its testing on a pilot-scale furnace. In Phase 2, a prototype analyzer will be constructed and tested on a commercial forehearth. This report covers the Phase 1 activities.

Gardner, M.; Candee, A.; Kramlich, J.; Koppang, R.

1991-05-01T23:59:59.000Z

84

Advanced Turbine Systems Program industrial system concept development  

DOE Green Energy (OSTI)

Solar approached Phase II of ATS program with the goal of 50% thermal efficiency. An intercolled and recuperated gas turbine was identified as the ultimate system to meet this goal in a commercial gas turbine environment. With commercial input from detailed market studies and DOE`s ATS program, Solar redefined the company`s proposed ATS to fit both market and sponsor (DOE) requirements. Resulting optimized recuperated gas turbine will be developed in two sizes, 5 and 15 MWe. It will show a thermal efficiency of about 43%, a 23% improvement over current industrial gas turbines. Other ATS goals--emissions, RAMD (reliability, availability, maintainability, durability), cost of power--will be met or exceeded. During FY95, advanced development of key materials, combustion and component technologies proceeded to the point of acceptance for inclusion in ATS Phase III.

Gates, S.

1995-12-31T23:59:59.000Z

85

Industry  

NLE Websites -- All DOE Office Websites (Extended Search)

in an Appliance Industry Abstract This report provides a starting point for appliance energy efficiency policy to be informed by an understanding of: the baseline rate and...

86

THE DEVELOPMENT OF A 1990 INDUSTRIAL ENERGY USE BASELINE  

E-Print Network (OSTI)

to determine total energy consumption for that industry. However, if specific energy intensities per unit consumption, and emissions generated by energy consumption, a comprehensive, baseline data set of industrial branches of Canadian industry, forms the goal of this report. An adequate baseline energy consumption

87

NETL: News Release - New Project to Help Develop Industry Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

September 20, 2001 September 20, 2001 New Project to Help Develop Industry Standards for Sonic Stimulation Technology Holds Promise for Boosting Oil Recovery TULSA, OK - Oil production in the United States is declining at an alarming rate. The remaining resources have high exploration and production costs and pose greater technical challenges. Some domestic oil wells are prematurely abandoned due to lacking technologies and economic instabilities. Sonic stimulation - the use of sound waves sent out through reservoir rock to free trapped oil droplets ? is an emerging technology that has been used in the last decade to enhance oil field production in the United States and overseas. While results have been positive in some cases, most of these applications did not contain sufficient scientific rigor to form a solid theoretical basis. Stimulation experts have concluded that this lack of basic understanding has led to widely varied tools and mechanisms with inconsistent yet promising results.

88

Federal/Industry Development of Energy-Conserving Technologies for the Chemical and Petroleum Refining Industries  

E-Print Network (OSTI)

Argonne National Laboratory has started a program to identify future RD&D projects that (i) promise cost-effective savings of scarce fuels in the chemical and petroleum refining industries, (ii) are not likely to be pursued by industry alone. This program, sponsored by the Office of Industrial Programs of DOE, defines technology needs from an industry viewpoint, so that recommended projects will complement industry's efforts and result in technologies for which there are clearly identifiable markets. The search for RD&D projects is currently focusing in the following technology categories: (i) reduction of fouling in cooling water systems, (ii) alternatives to conventional distillation and separation, (iii) low level waste heat recovery, (iv) advanced concepts in furnaces and boilers, (v) coal utilization, and (vi) advanced concepts in conversion and processing. The future direction of the program will continue to be dictated largely by industry needs.

Alston, T. G.; Humphrey, J. L.

1981-01-01T23:59:59.000Z

89

Industry  

NLE Websites -- All DOE Office Websites (Extended Search)

An Exploration of Innovation and An Exploration of Innovation and Energy Efficiency in an Appliance Industry Prepared by Margaret Taylor, K. Sydny Fujita, Larry Dale, and James McMahon For the European Council for an Energy Efficient Economy March 29, 2012 ERNEST ORLANDO LAWRENCE BERKELEY NATIONAL LABORATORY LBNL - 5689E An Exploration of Innovation and Energy Efficiency in an Appliance Industry Abstract This report provides a starting point for appliance energy efficiency policy to be informed by an understanding of: the baseline rate and direction of technological change of product industries; the factors that underlie the outcomes of innovation in these industries; and the ways the innovation system might respond to any given intervention. The report provides an overview of the dynamics of energy efficiency policy and innovation in the appliance

90

Industry  

E-Print Network (OSTI)

milling industry: An ENERGY STAR Guide for Energy and Plantcement mak- ing - An ENERGY STAR Guide for Energy and Plantre- fineries - An ENERGY STAR Guide for Energy and Plant

Bernstein, Lenny

2008-01-01T23:59:59.000Z

91

Assessment of industry needs for oil shale research and development  

SciTech Connect

Thirty-one industry people were contacted to provide input on oil shale in three subject areas. The first area of discussion dealt with industry's view of the shape of the future oil shale industry; the technology, the costs, the participants, the resources used, etc. It assessed the types and scale of the technologies that will form the industry, and how the US resource will be used. The second subject examined oil shale R D needs and priorities and potential new areas of research. The third area of discussion sought industry comments on what they felt should be the role of the DOE (and in a larger sense the US government) in fostering activities that will lead to a future commercial US oil shale shale industry.

Hackworth, J.H.

1987-05-01T23:59:59.000Z

92

US energy industry financial developments, 1993 third quarter  

SciTech Connect

Based on information provided in 1993 third quarter financial disclosures, the average net income for 112 petroleum companies -- including 18 majors -- rose 13 percent between the third quarter of 1992 and the third quarter of 1993. The gain in overall petroleum income was derived from increases in refined product consumption and margins, which improved the profitability of downstream petroleum (refining, marketing and transport) operations. A 17-percent decline in crude oil prices led to reduced income for upstream (oil and gas exploration, development and production) operations. A 16-percent rise in natural gas wellhead prices only partially offset the negative effects of low crude oil prices. Electric utilities also reported improved financial results for the third quarter of 1993 as hotter summer temperatures relative to the year-earlier quarter helped boost air conditioning demand and overall electricity usage. The following points highlight third-quarter energy industry financial developments: (1) Refined product demand and margins lift downstream earnings. Petroleum product consumption rose 2 percent between the third quarter of 1992 and the third quarter of 1993. Although petroleum product prices declined in the most recent reporting period, they did not decline as much as crude oil input prices. As a consequence, refined product margins widened. (2) Lower crude oil prices reduce upstream earnings. Crude oil prices fell 17 percent between the third quarter of 1992 and the third quarter of 1993 leading to a substantial reduction in income for the major petroleum companies` upstream operations. (3) Drilling income rises with increased North American exploratory activity.

Not Available

1993-12-01T23:59:59.000Z

93

Development of a Performance-Based Industrial Energy Efficiency...  

NLE Websites -- All DOE Office Websites (Extended Search)

that produce a variety of products - including corn starch, corn oil, animal feed, corn sweeteners, and ethanol -for the paper, food, beverage, and other industries in the...

94

Assessment of pre-competitive research and development needs for industrial waste minimization  

Science Conference Proceedings (OSTI)

This report summarizes the findings of the first phase of a study undertaken to define a role for the Advanced Industrial Concepts (AIC) Division of the Office of Industrial Technologies (OIT) in developing waste minimization technologies for the industrial sector. The report describes the results of an industrial waste characterization based mainly on the US Environmental Protection Agency`s (EPA`s) 1989 Toxics Release Inventory (TRI) database. IN addition, it contains the results of interviews with personnel from trade associations, environmental advocacy groups, federal agencies, and industrial firms regarding pre-competitive research and development needs for industrial waste minimization. Recommendations for future AIC waste minimization activities are provided.

Young, J.K.; Fassbender, L.L. [Pacific Northwest Lab., Richland, WA (United States); Sen, R.K. [Sen (R.K.) and Associates, Washington, DC (United States)

1992-02-01T23:59:59.000Z

95

Assessment of pre-competitive research and development needs for industrial waste minimization  

Science Conference Proceedings (OSTI)

This report summarizes the findings of the first phase of a study undertaken to define a role for the Advanced Industrial Concepts (AIC) Division of the Office of Industrial Technologies (OIT) in developing waste minimization technologies for the industrial sector. The report describes the results of an industrial waste characterization based mainly on the US Environmental Protection Agency's (EPA's) 1989 Toxics Release Inventory (TRI) database. IN addition, it contains the results of interviews with personnel from trade associations, environmental advocacy groups, federal agencies, and industrial firms regarding pre-competitive research and development needs for industrial waste minimization. Recommendations for future AIC waste minimization activities are provided.

Young, J.K.; Fassbender, L.L. (Pacific Northwest Lab., Richland, WA (United States)); Sen, R.K. (Sen (R.K.) and Associates, Washington, DC (United States))

1992-02-01T23:59:59.000Z

96

Development of mobile workforce management system for electricity supply industries  

Science Conference Proceedings (OSTI)

This research paper presents the features of a proposed Mobile Workforce Management System (MWMS) that will be used for the Electricity Supply Industries (ESI). The paper wraps up the types of related works that has been executed; the study on problems ... Keywords: electricity supply industry, mobile workforce management system

Faridah Hani Mohamed Salleh; Zaihisma Che Cob; Mohana Shanmugam; Siti Salbiah Mohamed Shariff

2009-12-01T23:59:59.000Z

97

Developing an energy efficiency service industry in Shanghai  

SciTech Connect

The rapid development of the Chinese economy over the past two decades has led to significant growth in China's energy consumption and greenhouse gas (GHG) emissions. Between 1980 and 2000, China's energy consumption more than doubled from 602 million to 1.3 billion tons of coal-equivalent (NBS, 2003). In 2000, China's GHG emissions were about 12% of the global total, ranked second behind only the US. According to the latest national development plan issued by the Chinese government, China's energy demand is likely to double again by 2020 (DRC, 2004), based on a quadrupling of its gross domestic product (GDP). The objectives of the national development plan imply that China needs to significantly raise the energy efficiency of its economy, i.e., cutting the energy intensity of its economy by half. Such goals are extremely ambitious, but not infeasible. China has achieved such reductions in the past, and its current overall level of energy efficiency remains far behind those observed in other developed economies. However, challenges remain whether China can put together an appropriate policy framework and the institutions needed to improve the energy efficiency of its economy under a more market-based economy today. Shanghai, located at the heart of the Yangtze River Delta, is the most dynamic economic and financial center in the booming Chinese economy. With 1% of Chinese population (13 million inhabitants), its GDP in 2000 stood at 455 billion RMB yuan (5% of the national total), with an annual growth rate of 12%--much higher than the national average. It is a major destination for foreign as well as Chinese domestic investment. In 2003, Shanghai absorbed 10% of actual foreign investment in all China (''Economist'', January 17-23, 2004). Construction in Shanghai continues at a breakneck pace, with an annual addition of approximately 200 million square foot of residential property and 100 million square foot of commercial and industrial space over the last 5 years. It is one reason that China consumed over 60% of the world's cement production in 2003 (NBS 2004). Energy consumption in Shanghai has been growing at 6-8% annually, with the growth of electricity demand at over 10% per year. Shanghai, with very limited local energy resources, relies heavily on imported coal, oil, natural gas, and electricity. While coal still constitutes over half of Shanghai's energy consumption, oil and natural gas use have been growing in importance. Shanghai is the major market for China's West to East (natural gas) Pipeline (WEP). With the input from WEP and off-shore pipelines, it is expected that natural gas consumption will grow from 250 million cubic meters in 2000 to 3000-3500 million cubic meters in 2005. In order to secure energy supply to power Shanghai's fast-growing economy, the Shanghai government has set three priorities in its energy strategy: (1) diversification of its energy structure, (2) improving its energy efficiency, and (3) developing renewable and other cleaner forms of energy. Efficiency improvements are likely to be most critical, particularly in the near future, in addressing Shanghai's energy security, especially the recent electricity shortage in Shanghai. Commercial buildings and industries consume the majority of Shanghai's, as well as China's, commercial energy. In the building sector, Shanghai has been very active implementing energy efficiency codes for commercial and residential buildings. Following a workshop on building codes implementation held at LBNL for senior Shanghai policy makers in 2001, the Shanghai government recently introduced an implementation guideline on residential building energy code compliance for the downtown area of Shanghai to commence in April, 2004, with other areas of the city to follow in 2005. A draft code for commercial buildings has been developed as well. In the industrial sector, the Shanghai government started an ambitious initiative in 2002 to induce private capital to invest in energy efficiency i

Lin, Jiang; Goldman, Charles; Levine, Mark; Hopper, Nicole

2004-02-10T23:59:59.000Z

98

Defining business strategy for development of travel and tourism industry  

E-Print Network (OSTI)

Many studies conducted on Travel and Tourism industry consider tourism an economic phenomenon. Providing a customer-satisfaction-based analysis, this thesis deals with both economic and social aspects. Economic data on ...

Davari, Dordaneh

2011-01-01T23:59:59.000Z

99

NRRI NowSpring/Summer 2008 GrowingStrongIndustries~DevelopingNewIdeas~NurturingNaturalResources  

E-Print Network (OSTI)

,500 mattresses a month to Duluth Goodwill Industries (and growing!) 360 pounds per cubic yard ­ compaction rateNRRI NowSpring/Summer 2008 GrowingStrongIndustries~DevelopingNewIdeas~NurturingNaturalResources 2 The afterlife of mattresses Birds in the riparian zone Pellet industry heats up Watchdogs for change Biology

Netoff, Theoden

100

NRC Postdoc Opportunities in Optoelectronics  

Science Conference Proceedings (OSTI)

... development of nanotemplates for patterned growth of nanowires; optimization of p ... 52.B5888 The calibration of laser power and energy, and optical ...

2011-10-24T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Development of a Performance-based Industrial Energy Efficiency Indicator  

NLE Websites -- All DOE Office Websites (Extended Search)

Pulp, Paper, and Paperboard Mills Pulp, Paper, and Paperboard Mills Secondary menu About us Press room Contact Us Portfolio Manager Login Facility owners and managers Existing buildings Commercial new construction Industrial energy management Small business Service providers Service and product providers Verify applications for ENERGY STAR certification Design commercial buildings Energy efficiency program administrators Commercial and industrial program sponsors Associations State and local governments Federal agencies Tools and resources Training In This Section Campaigns Commercial building design Communications resources Energy management guidance Financial resources Portfolio Manager Products and purchasing Recognition Research and reports Service and product provider (SPP) resources Success stories Target Finder

102

Development of a Performance-based Industrial Energy Efficiency Indicator  

NLE Websites -- All DOE Office Websites (Extended Search)

Automobile Assembly Plants Automobile Assembly Plants Secondary menu About us Press room Contact Us Portfolio Manager Login Facility owners and managers Existing buildings Commercial new construction Industrial energy management Small business Service providers Service and product providers Verify applications for ENERGY STAR certification Design commercial buildings Energy efficiency program administrators Commercial and industrial program sponsors Associations State and local governments Federal agencies Tools and resources Training In This Section Campaigns Commercial building design Communications resources Energy management guidance Financial resources Portfolio Manager Products and purchasing Recognition Research and reports Service and product provider (SPP) resources Success stories Target Finder

103

Development of a Performance-based Industrial Energy Efficiency Indicator  

NLE Websites -- All DOE Office Websites (Extended Search)

Pharmaceutical Manufacturing Plants Pharmaceutical Manufacturing Plants Secondary menu About us Press room Contact Us Portfolio Manager Login Facility owners and managers Existing buildings Commercial new construction Industrial energy management Small business Service providers Service and product providers Verify applications for ENERGY STAR certification Design commercial buildings Energy efficiency program administrators Commercial and industrial program sponsors Associations State and local governments Federal agencies Tools and resources Training In This Section Campaigns Commercial building design Communications resources Energy management guidance Financial resources Portfolio Manager Products and purchasing Recognition Research and reports Service and product provider (SPP) resources Success stories Target Finder

104

Development of a Performance-based Industrial Energy Efficiency Indicator  

NLE Websites -- All DOE Office Websites (Extended Search)

Cement Manufacturing Plants Cement Manufacturing Plants Secondary menu About us Press room Contact Us Portfolio Manager Login Facility owners and managers Existing buildings Commercial new construction Industrial energy management Small business Service providers Service and product providers Verify applications for ENERGY STAR certification Design commercial buildings Energy efficiency program administrators Commercial and industrial program sponsors Associations State and local governments Federal agencies Tools and resources Training In This Section Campaigns Commercial building design Communications resources Energy management guidance Financial resources Portfolio Manager Products and purchasing Recognition Research and reports Service and product provider (SPP) resources Success stories Target Finder

105

Development of a Performance-based Industrial Energy Efficiency Indicator  

NLE Websites -- All DOE Office Websites (Extended Search)

Corn Refining Plants Corn Refining Plants Secondary menu About us Press room Contact Us Portfolio Manager Login Facility owners and managers Existing buildings Commercial new construction Industrial energy management Small business Service providers Service and product providers Verify applications for ENERGY STAR certification Design commercial buildings Energy efficiency program administrators Commercial and industrial program sponsors Associations State and local governments Federal agencies Tools and resources Training In This Section Campaigns Commercial building design Communications resources Energy management guidance Financial resources Portfolio Manager Products and purchasing Recognition Research and reports Service and product provider (SPP) resources Success stories Target Finder Technical documentation

106

Industrial  

Gasoline and Diesel Fuel Update (EIA)

Industrial Industrial 8,870,422 44.3% Commercial 3,158,244 15.8% Electric Utilities 2,732,496 13.7% Residential 5,241,414 26.2% Source: Energy Information Administration (EIA), Form EIA-176, "Annual Report of Natural and Supplemental Gas Supply and Disposition." T e x a s L o u i s i a n a C a l i f o r n i a A l l O t h e r S t a t e s 0 1 2 3 4 5 0 30 60 90 120 Trillion Cubic Feet Industrial Billion Cubic Meters T e x a s C a l i f o r n i a F l o r i d a A l l O t h e r S t a t e s 0 1 2 3 4 5 0 30 60 90 120 Trillion Cubic Feet Electric Utilities Billion Cubic Meters N e w Y o r k C a l i f o r n i a I l l i n o i s A l l O t h e r S t a t e s 0 1 2 3 4 5 0 30 60 90 120 Trillion Cubic Feet Commercial Billion Cubic Meters I l l i n o i s C a l i f o r n i a N e w Y o r k A l l O t h e r S t a t e s 0 1 2 3 4 5 0 30 60 90 120 Trillion Cubic Feet Residential Billion Cubic Meters 11. Natural Gas Delivered to Consumers in the United States, 1996 Figure Volumes in Million Cubic Feet Energy Information Administration

107

Assembly of opto-electronic module with improved heat sink  

DOE Patents (OSTI)

A heat sink for a transceiver optoelectronic module including dual direct heat paths and a structure which encloses a number of chips having a central web which electrically isolates transmitter and receiver chips from each other. A retainer for an optical coupler having a port into which epoxy is poured. An overmolded base for an optoelectronic module having epoxy flow controller members built thereon. Assembly methods for an optoelectronic module including gap setting and variation of a TAB bonding process.

Chan, Benson (Vestal, NY); Fortier, Paul Francis (Richelieu, CA); Freitag, Ladd William (Rochester, MN); Galli, Gary T. (Binghampton, NY); Guindon, Francois (Stukely-sud, CA); Johnson, Glen Walden (Yorktown Heights, NY); Letourneau, Martial (Granby, CA); Sherman, John H. (Lisle, NY); Tetreault, Real (Granby, CA)

2004-11-23T23:59:59.000Z

108

Estimating energy-augmenting technological change in developing country industries  

E-Print Network (OSTI)

over time is calculated. Second, prices and the energy costTime averages of sectoral productivity and autonomous energy efficiency trend Industry Prices and energy costTime averages (in percent) of sectoral productivity and autonomous energy efficiency trend Prices and energy cost

Sanstad, Alan H.; Roy, Joyashree; Sathaye, Jayant A.

2006-01-01T23:59:59.000Z

109

Industrial heat pumps in Germany -potentials, technological development  

E-Print Network (OSTI)

jet nozzle Closed Cycles: Absorption/Adsorption heat pump thermal compressor driven by waste heat to 80 COP heating 2.5 to 5.8 Cooling function 50% of manufacturers offer cooling functions Cooling capacity [kW] 20 to 2500 COP cooling 1 to 6 #12;ACHEMA 2012 - Industrial heat pumps 21st June 2012

Oak Ridge National Laboratory

110

US energy industry financial developments, 1994 first quarter  

SciTech Connect

This report traces key financial trends in the US energy industry for the first quarter of 1994. Financial data (only available for publicly-traded US companies) are included in two broad groups -- fossil fuel production and rate-regulated electric utilities. All financial data are taken from public sources such as energy industry corporate reports and press releases, energy trade publications, and The Wall Street Journal`s, Earnings Digest. Return on equity is calculated from data available from Standard and Poor`s Compustat data service. Since several major petroleum companies disclose their income by lines of business and geographic area. These data are also presented in this report. Although the disaggregated income concept varies by company and is not strictly comparable to corporate income, relative movements in income by lines of business and geographic area are summarized as useful indicators of short-term changes in the underlying profitability of these operations.

1994-06-23T23:59:59.000Z

111

Industry  

E-Print Network (OSTI)

than 1400 energy policies being considered by governmentsof its energy and climate policy the Dutch government hasgovernment intervention on the development of strip casting technology. Energy Policy,

Bernstein, Lenny

2008-01-01T23:59:59.000Z

112

Industry  

E-Print Network (OSTI)

Development of energy intensity indicators for Canadianvarious indicators to present energy intensity, including energy intensity, which is a constructed indicator, making

Bernstein, Lenny

2008-01-01T23:59:59.000Z

113

Technologies, markets and challenges for development of the Canadian Oil Sands industry  

E-Print Network (OSTI)

This paper provides an overview of the current status of development of the Canadian oil sands industry, and considers possible paths of further development. We outline the key technology alternatives, critical resource ...

Lacombe, Romain H.

2007-01-01T23:59:59.000Z

114

Societal and technical issues in the industrial development of Saudi Arabia and Egypt  

E-Print Network (OSTI)

Sustained industrial development in developing nations has been an impetus for economic growth and technological advancements for the past several decades, in addition to being a major contributor to poverty reduction. ...

Kundukulam, Vibin A. (Vibin Anto)

2011-01-01T23:59:59.000Z

115

Industrial Uses of Vegetable OilsChapter 2 Current Developments of Biodegradable Grease  

Science Conference Proceedings (OSTI)

Industrial Uses of Vegetable Oils Chapter 2 Current Developments of Biodegradable Grease Processing eChapters Processing Press Downloadable pdf of Chapter 2 Current Developments of Biodegradable Grease from the bo

116

Industrial Uses of Vegetable OilsChapter 7 Development of Soy Composites by Direct Deposition  

Science Conference Proceedings (OSTI)

Industrial Uses of Vegetable Oils Chapter 7 Development of Soy Composites by Direct Deposition Processing eChapters Processing Press Downloadable pdf of Chapter 7 Development of Soy Composites by Direct Deposition

117

Design and development of an automated pinning machine for the surface mount electronics industry  

E-Print Network (OSTI)

This thesis describes the development of a concept for a pinning process and the associated machinery to handle odd-form pins specific to a company in the surface mount electronics industry. The developed pinning machine ...

Cook, Daniel J., M. Eng. (Daniel James). Massachusetts Institute of Technology

2012-01-01T23:59:59.000Z

118

Facilitating Wind Development: The Importance of Electric Industry Structure  

DOE Green Energy (OSTI)

This paper evaluates which wholesale elecricity market-structure characteristics best accommodate wind energy development.

Kirby, B.; Milligan, M.

2008-05-01T23:59:59.000Z

119

Solar Photovoltaic Economic Development: Building and Growing a Local PV Industry, August 2011 (Book)  

DOE Green Energy (OSTI)

The U.S. photovoltaic (PV) industry is forecast to grow, and it represents an opportunity for economic development and job creation in communities throughout the United States. This report helps U.S. cities evaluate economic opportunities in the PV industry. It serves as a guide for local economic development offices in evaluating their community?s competitiveness in the solar PV industry, assessing the viability of solar PV development goals, and developing strategies for recruiting and retaining PV companies to their areas.

Not Available

2011-08-01T23:59:59.000Z

120

The predictions of optoelectronic attributes of LED by neural network  

Science Conference Proceedings (OSTI)

In this paper, the predictions of optoelectronic attributes of Light-Emitting Diode (LED) chip, including luminous intensity, wavelength and forward voltage by using neural network were presented. The simulated data was measured by Electrical Luminescence ... Keywords: Neural network, Optoelectronic attributes, Prediction

Pin-Hsuan Weng; Yu-Ju Chen; Shuming T. Wang; Rey-Chue Hwang

2010-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Development of a Performance-based Industrial Energy Efficiency...  

NLE Websites -- All DOE Office Websites (Extended Search)

is useful if you would like background information on how EPA's ENERGY STAR Wet Corn Milling Plant EPI was developed. The report presents the individual equations used to develop...

122

Latest Developments in Spark OES for Iron and Steel Industry  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, Materials Science & Technology 2009. Symposium, Inclusions and Clean Steels. Presentation Title, Latest Developments in Spark...

123

Development of Inexpensive Turbo Compressor/Expanders for Industrial Use  

E-Print Network (OSTI)

Use of Turbo Compressor/ Expanders (TCEs) as industrial reversed Brayton Cycle Heat Pumps offers many technical and energy saving advantages. Until recently, such devices have been far too expensive in both capital cost and inefficiency mainly because the compressor and expander stages were built for forward Brayton Cycle operation in unmatched compressor/expander efficiencies. A few years ago, NUCON initiated a program to locate sources of TCEs and to engineer cost effective modifications to these standard TCEs for use in reverse Brayton Cycle condensation based pollution control and solvent recovery, material recycle applications. The NUCON program is continuing to further improve the matched compressor/expander efficiency, the availability and cost effectiveness of these uses. This program has resulted in major advances in availability and significant improvements in efficiency.

Jacox, J. W.

1991-06-01T23:59:59.000Z

124

US Energy Industry Financial Developments, 1993 fourth quarter, April 1994  

Science Conference Proceedings (OSTI)

This report traces key financial trends in the US energy industry for the fourth quarter of 1993. Financial data (only available for publicly-traded US companies) are included in two broad groups -- fossil fuel production and rate-regulated electric utilities. All financial data are taken from public sources such as energy industry corporate reports and press releases, energy trade publications, and The Wall Street Journal`s Earnings Digest; return on equity is calculated from data available from Standard and Poor`s Compustat data service. Since several major petroleum companies disclose their income by lines of business and geographic area, these data are also presented in this report. Although the disaggregated income concept varies by company and is not strictly comparable to corporate income, relative movements in income by lines of business and geographic area are summarized as useful indicators of short-term changes in the underlying profitability of these operations. Based on information provided in 1993 fourth quarter financial disclosures, the net income for 82 petroleum companies -- including 18 majors -- was unchanged between the fourth quarter of 1992 and the fourth quarter of 1993. An 18-percent decline in crude oil prices resulted in a deterioration of the performance of upstream (oil and gas production) petroleum companies during the final quarter of 1993. However, prices for refined products fell much less than the price of crude oil, resulting in higher refined product margins and downstream (refining, marketing and transport) petroleum earnings. An increase in refined product demand also contributed to the rise in downstream income.

Not Available

1994-04-14T23:59:59.000Z

125

Developing a Sustainable Forest Biomass Industry: Case of the US Northeast  

E-Print Network (OSTI)

Developing a Sustainable Forest Biomass Industry: Case of the US Northeast D. Damery1 , J. Benjamin in renewable energy has produced a spate of new research into the feasibility of forest biomass as a feedstock, and social considerations that must be addressed in order to achieve a sustainable forest biomass industry

Schweik, Charles M.

126

Combustion System Development for Medium-Sized Industrial Gas Turbines: Meeting Tight Emission Regulations while Using  

E-Print Network (OSTI)

Combustion System Development for Medium-Sized Industrial Gas Turbines: Meeting Tight Emission and the oil & gas industries. The combustion system used in Solar's products are discussed along- bility for the introduction of new combustion systems for gas turbine products to enhance fuel

Ponce, V. Miguel

127

Development & expansion of an industrial control system security laboratory and an international research collaboration  

Science Conference Proceedings (OSTI)

In this paper, we describe the incremental building of a unique industrial control system laboratory designed to investigate security vulnerabilities and to support development of mitigating tools and techniques. The laboratory has been built over time ... Keywords: SCADA, critical infrastructure security, industrial control systems, test bed

Rayford B. Vaughn; Thomas Morris; Elena Sitnikova

2013-01-01T23:59:59.000Z

128

Development of Ni Base Superalloy for Industrial Gas Turbine  

Science Conference Proceedings (OSTI)

In response to this demand, Ni-base superalloys have been developed by MHI's alloy design system. These Ni-base superalloys have been applied to rotating...

129

The use of industrial energy in seven OECD (Organization for Economic Cooperation and Development) countries  

SciTech Connect

The objective of this study was to analyze the industrial demand for energy in seven Organization for Economic Cooperation and Development (OECD) countries with particular emphasis on fuel substitution between oil, natural gas, coal, and electricity. Changing fuel demand also results from economic growth, changes in industrial structure, and changes in the energy intensity of industrial output. A historical analysis of these factors and fuel substitution is undertaken for industry as an aggregate, and for 12 specific industries. The major results of the historical analysis are: (1) fuel use changes are a result of fuel switching, changing energy intensity, changing industrial structure, and economic growth; (2) fuel substitutability depends upon fuel use. The three fossil fuels are substitutes in the industrial heat market, but there are numerous special industrial processes where a particular fuel is required; (3) large substitutions have occurred between fuels; (4) fuel substitutions have been very different across countries, both in the type of substitutions that have occurred and the factors accounting for the substitutions; and (5) in most countries, major changes in fuel use can be explained by two or three industries, suggesting that future analyses be industry specific.

Sutherland, R.J.

1987-01-01T23:59:59.000Z

130

Case Studies in Sustainable Development in the Coal Industry | Open Energy  

Open Energy Info (EERE)

Studies in Sustainable Development in the Coal Industry Studies in Sustainable Development in the Coal Industry Jump to: navigation, search Name Case Studies in Sustainable Development in the Coal Industry Agency/Company /Organization International Energy Agency Sector Energy Focus Area Conventional Energy Topics Implementation Resource Type Guide/manual, Lessons learned/best practices Website http://www.iea.org/papers/2006 Program Start 2006 References Case Studies in Sustainable Development in the Coal Industry[1] Summary "Widely held attitudes to coal's use have evolved greatly in the past five years - from those that largely dismissed a role for coal in sustainable development to a wider appreciation of coal's continuing role in providing a foundation for energy security and in meeting growing world energy

131

Wind Energy Workforce Development: A Roadmap to a Sustainable Wind Industry (Poster)  

SciTech Connect

As the United States moves toward a vision of greatly expanded wind energy use as outlined in the U.S. Department of Energy's 20% Wind Energy by 2030 report, the need for skilled workers at all levels in the industry is repeatedly identified as a critical issue. This presentation is an overview of the educational infrastructure and expected industry needs to support the continued development of a vibrant U.S. wind industry through a discussion of the activities identified that must be put in place to train workers. The paper will also provide a framework to address issues raised from each of the education and industry sectors, identifying a roadmap for developing an educational infrastructure to support wind technology. The presentation will also provide an understanding of the available resources, materials, and programs available across the industry. This presentation provides an overview of the educational infrastructure and expected industry needs to support the continued development of a vibrant U.S. wind industry as part of a collaborative effort to develop a wind workforce roadmap. This presentation will provide 1) A review of needed programs to train workers for the wind industry; 2) An overview of the importance education will play if the nation is to expand wind energy (both in development and deployment terms) and a review of ongoing activities with a focus on federal efforts; 3) A review of the materials and resources available across the industry and a framework to address issues raised from each of the education and industry sectors.

Baring-Gould, I.; Kelly, M.

2010-05-01T23:59:59.000Z

132

Challenges for agile development of large systems in the aviation industry  

Science Conference Proceedings (OSTI)

The current challenges of the aviation industry call for the development of new and revolutionary aircraft concepts. In general, the task of developing new aircraft is risky and an extremely complex task, and aircraft manufacturers seek to control this ... Keywords: agile development, certification, change notification, development risk, generative design, open tool platform, situation awareness

Martin Glas; Sven Ziemer

2009-10-01T23:59:59.000Z

133

Palm Oil: Production, Processing, Uses, and CharacterizationChapter 25 Sustainable Development of Palm Oil Industry  

Science Conference Proceedings (OSTI)

Palm Oil: Production, Processing, Uses, and Characterization Chapter 25 Sustainable Development of Palm Oil Industry Food Science Health Nutrition Biochemistry Processing eChapters Food Science & Technology Health - Nutrition - Biochemi

134

A framework for developing, manufacturing, and sourcing trucks & equipment in a global fluid management industry  

E-Print Network (OSTI)

Selecting and executing the optimal strategy for developing new products is a non trivial task, especially for low volume, high complexity products in a highly volatile global industry such as Fluid Management. At Fluid ...

Awwad, Ghassan Samir

2009-01-01T23:59:59.000Z

135

United Nations Industrial Development Organization Feed | Open Energy  

Open Energy Info (EERE)

Feed Feed Jump to: navigation, search Home | About | Inventory | Partnerships | Capacity Building | Webinars | Reports | Events | News | List Serve CLEAN Member Feeds Center for Environment and National Security at Scripps Centro de Energías Renovables (CER) The Children's Investment Fund Foundation (CIFF) Climate and Development Knowledge Network (CDKN) Climate Technology Initiative (CTI) ClimateWorks Foundation Coalition for Rainforest Nations (CfRN) Ecofys Energy Research Centre of the Netherlands (ECN) Energy Sector Management Assistance Program of the World Bank (ESMAP) Environment and Development Action in the Third World (ENDA-TM) German Aerospace Center (DLR) German Agency for International Cooperation (GIZ) Global Village Energy Partnership (GVEP) Information for Development Program (infoDev)

136

Hybrid Semiconductors for Hardier Electronics and Optoelectronics? |  

NLE Websites -- All DOE Office Websites (Extended Search)

Unveiling the Molecular Structure of the Target of Many Drugs Unveiling the Molecular Structure of the Target of Many Drugs A New Scenario for First Life on Earth Surface Orbital 'Roughness' in Colossal Magnetoresistive Oxide Different Roads Toward Quantum Criticality Orbital Reconstruction at a Complex Oxide Interface Science Highlights Archives: 2013 | 2012 | 2011 | 2010 2009 | 2008 | 2007 | 2006 2005 | 2004 | 2003 | 2002 2001 | 2000 | 1998 | Subscribe to APS Science Highlights rss feed Hybrid Semiconductors for Hardier Electronics and Optoelectronics? DECEMBER 21, 2007 Bookmark and Share The crystal structure of β-ZnTe(en)0:5, determined by single-crystal x-ray diffraction. Two-monolayerthick ZnTe slabs are interconnected by ethylenediamine (C2N2H8) molecules bonded to zinc atoms. Zn-Green, Te-Red, N-Blue,and C-Gray. Hydrogen atoms are omitted for clarity.

137

Development of a model for reactive emissions from industrial stacks  

Science Conference Proceedings (OSTI)

We have developed a model, CAPAS, capable of estimating short-term concentrations of primary and secondary pollutants resulting from point source emissions. The model is designed to simulate the complex interaction of plume dispersion and non-linear ... Keywords: Air pollutants, Dispersion models, Non-linear chemistry, Plume reactivity, Stiff solvers

Luis E. Olcese; Beatriz M. Toselli

2005-10-01T23:59:59.000Z

138

Facilitating wind development: the importance of electric industry structure  

Science Conference Proceedings (OSTI)

ISOs and RTOs, with their day-ahead and real-time markets, large geographies to aggregate diverse wind resources, large loads to aggregate with wind, large generation pools that tap conventional-generator flexibility, and regional transmission planning efforts, offer the best environments for wind generation to develop. (author)

Kirby, Brendan; Milligan, Michael

2008-04-15T23:59:59.000Z

139

Techno-Industrial Cooperation for Development in the Two Punjabs  

E-Print Network (OSTI)

and exploitation of technological knowledge can be done at global level. There is also a growing trend towards location of innovation units other than in their home country. Outsourcing of research and development (R&D) centres, opening up of R&D subsidiaries... to secure comparative advantage in the global economy. This along with the emergence Peace and Democracy in South Asia, Volume 1, Issue 2, 2005. 88 of genetically modified seeds technology has created opportunities for the firms in the advanced...

Singh, Lakhwinder

2005-01-01T23:59:59.000Z

140

U.S. Energy Industry Financial Developments 1995 First Quarter  

Reports and Publications (EIA)

This report traces key developments in U.S. energy companies' financial performance for the first quarter of 1995. Financial data (only available for publicly-traded U.S. companies) are included in two broad groups--fossil fuel production and rate-regulated utilities. All financial data are taken from public sources such as corporate reports and press releases, energy trade publications, and The Wall Street Journal's Earnings Digest.

Neal Davis

1995-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Department of Energy Awards $600,000 to Tri-City Industrial Development Council Community Reuse Organization  

Energy.gov (U.S. Department of Energy (DOE))

Department of Energy Awards $600,000 to Tri-City Industrial Development Council Community Reuse Organization

142

Federal agencies active in chemical industry-related research and development  

SciTech Connect

The Energy Policy Act of 1992 calls for a program to further the commercialization of renewable energy and energy efficient technologies for the industrial sector.. The primary objective of the Office of Industrial Technologies Chemical Industry Team is to work in partnership with the US chemical industry to maximize economic, energy, and environmental benefits through research and development of innovative technologies. This document was developed to inventory organizations within the federal government on current chemical industry-related research and development. While an amount of funding or number of projects specifically relating to chemical industry research and development was not defined in all organizations, identified were about 60 distinct organizations representing 7 cabinet-level departments and 4 independent agencies, with research efforts exceeding $3.5 billion in fiscal year 1995. Effort were found to range from less than $500 thousand per year at the Departments of Agriculture and the Interior to over $100 million per year at the Departments of Commerce, Defense, Energy, and Health and Human Services and the National Aeronautics and Space Administration. The total number of projects in these programs exceeded 10,000. This document is complete to the extent that agencies volunteered information. Additions, corrections, and changes are encouraged and will be incorporated in future revisions.

1995-09-29T23:59:59.000Z

143

Design and synthesis of nanocrystal heterostructures for optoelectronic applications  

E-Print Network (OSTI)

Colloidal semiconductor nanocrystals can be used for a variety of optoelectronic applications including light emitting devices (LEDs) and photovoltaics. Their narrow emission spectra make them excellent fluorophors for use ...

Halpert, Jonathan E

2008-01-01T23:59:59.000Z

144

Optoelectronic device with nanoparticle embedded hole injection/transport layer  

DOE Patents (OSTI)

An optoelectronic device is disclosed that can function as an emitter of optical radiation, such as a light-emitting diode (LED), or as a photovoltaic (PV) device that can be used to convert optical radiation into electrical current, such as a photovoltaic solar cell. The optoelectronic device comprises an anode, a hole injection/transport layer, an active layer, and a cathode, where the hole injection/transport layer includes transparent conductive nanoparticles in a hole transport material.

Wang, Qingwu (Chelmsford, MA); Li, Wenguang (Andover, MA); Jiang, Hua (Methuen, MA)

2012-01-03T23:59:59.000Z

145

An overview of industry-military cooperation in the development of power  

Open Energy Info (EERE)

An overview of industry-military cooperation in the development of power An overview of industry-military cooperation in the development of power operations at the Coso geothermal field in southern California Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: An overview of industry-military cooperation in the development of power operations at the Coso geothermal field in southern California Abstract The Coso Geothermal Field, located in east central California, hosts a world-class power-generating project that has been in continuous operation for the past 15 years. The project is located on the test and evaluation ranges of the Naval Air Weapons Station, China Lake-the Navy's premier research and development (R&D) facility for air-to-air and air-to-ground ordnance. Fully financed by private investment, the Coso geothermal power

146

NNMI Irvine Workshop Plenary Slides  

Science Conference Proceedings (OSTI)

... Indiana Optoelectronics Industry Development Association SEMATECH ... Network The Solar Energy Consortium ... Metal Powder Industries Federation ...

2013-01-23T23:59:59.000Z

147

Overview of U. S. Department of Energy Program in Industrial Energy Conservation Technology Development  

E-Print Network (OSTI)

The primary responsibility for Federal industrial energy conservation is in the Office of Industrial Programs which reports to the Assistant Secretary for Conservation and Solar Energy. The objectives of the Federal program are to: achieve maximum implementation of existing and new energy conservation technologies; substitute, where possible, abundant fuels for scarce fuels; and minimize energy loss in waste streams. The basic strategy is cost-shared research, development, and demonstration leading to commercialization of energy-efficient technology. Considerations for project selection are: energy savings, acceleration of implementation, level of private effort, benefits to industry, cost-sharing, and degree of risk. Projected industry savings of the current program are 1.5 Quads by 1985 and 5.5 Quads by 2000.

Massey, R. G.

1980-01-01T23:59:59.000Z

148

Industrial Advanced Turbine Systems: Development and Demonstration. Annual report, September 14, 1995--September 30, 1996  

DOE Green Energy (OSTI)

The U.S. Department of Energy (DOE) has initiated a program for advanced turbine systems (ATS) that will serve industrial power generation markets. The objective of the cooperative agreements granted under the program is to join the DOE with industry in research and development that will lead to commercial offerings in the private sector. The ATS will provide ultra-high efficiency, environmental superiority, and cost competitiveness. The ATS will foster (1) early market penetration that enhances the global competitiveness of U.S. industry, (2) public health benefits resulting from reduced exhaust gas emissions of target pollutants, (3) reduced cost of power used in the energy-intensive industrial marketplace and (4) the retention and expansion of the skilled U.S. technology base required for the design, development and maintenance of state-of-the-art advanced turbine products. The Industrial ATS Development and Demonstration program is a multi-phased effort. Solar Turbines Incorporated (Solar) has participated in Phases 1 and 2 of the program. On September 14, 1995 Solar was awarded a Cooperative Agreement for Phases 3 and 4 of the program (DE-FC21-95MC31173) by the DOE`s Office of Energy Efficiency and Renewable Energy (EE). Technical administration of the Cooperative Agreement will be provided from EE`s Chicago Operations Office. Contract administration of the Cooperative Agreement will be provided from DOE`s Office of Fossil Energy, Morgantown Energy Technology Center (METC).

NONE

1998-12-31T23:59:59.000Z

149

Development of a performance-based industrial energy efficiency indicator for cement manufacturing plants.  

SciTech Connect

Organizations that implement strategic energy management programs have the potential to achieve sustained energy savings if the programs are carried out properly. A key opportunity for achieving energy savings that plant managers can take is to determine an appropriate level of energy performance by comparing the plant performance with that of similar plants in the same industry. Manufacturing plants can set energy efficiency targets by using performance-based indicators. The U.S. Environmental Protection Agency (EPA), through its ENERGY STAR{reg_sign} program, has been developing plant energy performance indicators (EPIs) to encourage a variety of U.S. industries to use energy more efficiently. This report describes work with the cement manufacturing industry to provide a plant-level indicator of energy efficiency for assembly plants that produce a variety of products, including Portland cement and other specialty cement products, in the United States. Consideration is given to the role that performance-based indicators play in motivating change; the steps needed to develop indicators, including interacting with an industry to secure adequate data for an indicator; and the actual application and use of an indicator when complete. How indicators are employed in the EPA's efforts to encourage industries to voluntarily improve their use of energy is discussed as well. The report describes the data and statistical methods used to construct the EPI for cement manufacturing plants. Individual equations are presented, as are the instructions for using them in an associated Excel spreadsheet.

Boyd, G.; Decision and Information Sciences

2006-07-21T23:59:59.000Z

150

Human resource needs and development for the gas industry of the future  

SciTech Connect

The natural gas industry will confront many challenges in the 1990s and beyond, one of which is the development of human resources to meet future needs. An efficient, trained work force in this era of environmental concern, high technology, and alternative fuels is essential for the industry to continue to meet the competition and to safely deliver our product and service to all customers. Unfortunately, during this period there will be an increasing shortfall of technical personnel to replace those lost to attrition and a steady decline in the availability of new employees who are able to read, write, and perform simple math. Technological and government developments that will impact the industry and the skill levels needed by the industry employees are reviewed. In-house and external training of professional and nonprofessional personnel and the benefits and disadvantages of selected advanced training methods are discussed. Recommendations are presented that can help improve the training of gas industry employees to meet future needs. 22 refs.

Klass, D.L.

1991-01-01T23:59:59.000Z

151

Development of a performance-based industrial energy efficiency indicator for cement manufacturing plants.  

SciTech Connect

Organizations that implement strategic energy management programs have the potential to achieve sustained energy savings if the programs are carried out properly. A key opportunity for achieving energy savings that plant managers can take is to determine an appropriate level of energy performance by comparing the plant performance with that of similar plants in the same industry. Manufacturing plants can set energy efficiency targets by using performance-based indicators. The U.S. Environmental Protection Agency (EPA), through its ENERGY STAR{reg_sign} program, has been developing plant energy performance indicators (EPIs) to encourage a variety of U.S. industries to use energy more efficiently. This report describes work with the cement manufacturing industry to provide a plant-level indicator of energy efficiency for assembly plants that produce a variety of products, including Portland cement and other specialty cement products, in the United States. Consideration is given to the role that performance-based indicators play in motivating change; the steps needed to develop indicators, including interacting with an industry to secure adequate data for an indicator; and the actual application and use of an indicator when complete. How indicators are employed in the EPA's efforts to encourage industries to voluntarily improve their use of energy is discussed as well. The report describes the data and statistical methods used to construct the EPI for cement manufacturing plants. Individual equations are presented, as are the instructions for using them in an associated Excel spreadsheet.

Boyd, G.; Decision and Information Sciences

2006-07-21T23:59:59.000Z

152

Industrial advanced turbine systems: Development and demonstration. Quarterly report, January 1--March 31, 1998  

SciTech Connect

The US Department of Energy (DOE) has initiated a program for advanced turbine systems (ATS) that will serve industrial power generation markets. The objective of the cooperative agreements granted under the program is to join the DOE with industry in research and development that will lead to commercial offerings in the private sector. The ATS will provide ultra-high efficiency, environmental superiority, and cost competitiveness. The ATS will foster (1) early market penetration that enhances the global competitiveness of US industry, (2) public health benefits resulting from reduced exhaust gas emissions of target pollutants, (3) reduced cost of power used in the energy-intensive industrial marketplace, and (4) the retention and expansion of the skilled US technology base required for the design, development and maintenance of state-of-the-art advanced turbine products. The Industrial ATS Development and Demonstration program is a multi-phased effort. Solar Turbines Incorporated (Solar) has participated in Phases 1 and 2 of the program. On September 14, 1995 Solar was awarded a Cooperative Agreement for Phases 3 and 4 of the program. Phase 3 of the work is separated into two subphases: Phase 3A entails Component Design and Development; Phase 3B will involve Integrated Subsystem Testing. Phase 4 will cover Host Site Testing. As of the end of the reporting period work on the program is 29.1% complete (24.7% last quarter). Work on the Mercury 50 development and ATS technology development portions of the program (WBS 10000 et seq) is 48.9% complete (41.6% last quarter). Estimates of percent complete are based upon milestones completed. In order to maintain objectivity in assessing schedule progress, Solar uses a 0/100 percent complete assumption for milestones rather than subjectively estimating progress toward completion of milestones. Cost and schedule variance information is provided in Section 4.0 Program Management.

NONE

1998-08-01T23:59:59.000Z

153

Agent-based intelligent system development for decision support in chemical process industry  

Science Conference Proceedings (OSTI)

This paper presents an agent-based intelligent system to support coordinate manufacturing execution and decision-making in chemical process industry. A multi-agent system (MAS) framework is developed to provide a flexible infrastructure for the integration ... Keywords: Artificial intelligence, Coordinate manufacturing, Decision support, Information integration, Multi-agent system

Ying Gao; Zhigang Shang; Antonis Kokossis

2009-10-01T23:59:59.000Z

154

Analyzing the oil refining industry in developing countries: A comparative study of China and India  

SciTech Connect

The oil refining industry is a critical link in the energy chain in many developing and industrialized countries, transforming crude oil into transport fuels (gasoline, jet fuel, and diesel), residual fuel oil (widely used as a fuel in industry and the electric power sector), and other products such as kerosine, frequently for lighting an cooking usages. Three to four decades ago, the demand for oil products in most developing countries was centered to a few large cities; thus, few refineries were built in these regions. But because of the astonishing economic growth in many developing nations, demand for oil products has increased rapidly. As a result, the refining industry has expanded rapidly in such countries, even in cases were there is no domestic crude oil production. Oil product demand and refinery expansion in Asian developing countries in particular have experienced significant growth. Between 1976 and 1993, oil product demand and refinery capacity in that region (excluding Japan) increased annually an average of 5.2 percent and 4.3 percent, respectively, whereas the comparable figures for the world as a whole remained virtually unchanged during the same period. The substantial gains in Asia`s crude oil production in the 1970s is believed to have facilitated this refinery expansion.

Tang, F.C.

1994-12-31T23:59:59.000Z

155

Social media in the product development process of the automotive industry: a new approach  

Science Conference Proceedings (OSTI)

This paper introduces a new methodology for implementing social media monitoring into an important stage of the innovation process within the automotive industry -- the prototype stage. The information gathered on social media channels was used for project ... Keywords: electric mobility, electric vehicles, product development, social media monitoring, social networking sites

Andreas Klein, Gtz Spiegel

2013-07-01T23:59:59.000Z

156

Foster Wheeler Solar Development Corporation modular industrial solar retrofit qualification test results  

DOE Green Energy (OSTI)

Under the Department of Energy's Modular Industrial Solar Retrofit project, industrial process steam systems incorporating line-focus solar thermal collectors were designed and hardware was installed and tested. This report describes the test results for the system designed by Foster Wheeler Solar Development Corporation. The test series included function and safety tests to determine that the system operated as specified, an unattended operations test to demonstrate automatic operation, performance tests to provide a database for predicting system performance, and life cycle tests to evaluate component and maintenance requirements. Component-level modifications to improve system performance and reliability were also evaluated.

Cameron, C.P.; Dudley, V.E.; Lewandoski, A.A.

1986-10-01T23:59:59.000Z

157

AquaLite Wuhan Di Yuan Optoelectronic | Open Energy Information  

Open Energy Info (EERE)

AquaLite Wuhan Di Yuan Optoelectronic AquaLite Wuhan Di Yuan Optoelectronic Jump to: navigation, search Name AquaLite (Wuhan Di Yuan Optoelectronic) Place Wuhan, Hubei Province, China Zip 430074 Product High-power and high-brightness LED manufacturer. Coordinates 30.572399°, 114.279121° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":30.572399,"lon":114.279121,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

158

Method of fabricating an optoelectronic device having a bulk heterojunction  

DOE Patents (OSTI)

A method of fabricating an optoelectronic device comprises: depositing a first layer having protrusions over a first electrode, in which the first layer comprises a first organic small molecule material; depositing a second layer on the first layer such that the second layer is in physical contact with the first layer; in which the smallest lateral dimension of the protrusions are between 1 to 5 times the exciton diffusion length of the first organic small molecule material; and depositing a second electrode over the second layer to form the optoelectronic device. A method of fabricating an organic optoelectronic device having a bulk heterojunction is also provided and comprises: depositing a first layer with protrusions over an electrode by organic vapor phase deposition; depositing a second layer on the first layer where the interface of the first and second layers forms a bulk heterojunction; and depositing another electrode over the second layer.

Shtein, Max (Ann Arbor, MI); Yang, Fan (Princeton, NJ); Forrest, Stephen R. (Princeton, NJ)

2008-10-14T23:59:59.000Z

159

The Paradox of Regulatory Development in China: The Case of the Electricity Industry  

E-Print Network (OSTI)

Chinese electric power industry). ? Zhongguo Dianliwang (in Chinese State Industry: An Analysis of Evidence onchanye (Chinas Electricity Industry at the Crossroad). ? In

Tsai, Chung-min

2010-01-01T23:59:59.000Z

160

The Paradox of Regulatory Development in China: The Case of the Electricity Industry  

E-Print Network (OSTI)

chanye (Chinas Electricity Industry at the Crossroad). ? InCapture in the Electricity Industry 2. Cross-Sectorals Telecoms and Electricity Industries. ? European Journal of

Tsai, Chung-min

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Development of a performance-based industrial energy efficiency indicator for corn refining plants.  

Science Conference Proceedings (OSTI)

Organizations that implement strategic energy management programs have the potential to achieve sustained energy savings if the programs are carried out properly. A key opportunity for achieving energy savings that plant managers can take is to determine an appropriate level of energy performance by comparing their plant's performance with that of similar plants in the same industry. Manufacturing facilities can set energy efficiency targets by using performance-based indicators. The U.S. Environmental Protection Agency (EPA), through its ENERGY STAR{reg_sign} program, has been developing plant energy performance indicators (EPIs) to encourage a variety of U.S. industries to use energy more efficiently. This report describes work with the corn refining industry to provide a plant-level indicator of energy efficiency for facilities that produce a variety of products--including corn starch, corn oil, animal feed, corn sweeteners, and ethanol--for the paper, food, beverage, and other industries in the United States. Consideration is given to the role that performance-based indicators play in motivating change; the steps needed to develop indicators, including interacting with an industry to secure adequate data for an indicator; and the actual application and use of an indicator when complete. How indicators are employed in the EPA's efforts to encourage industries to voluntarily improve their use of energy is discussed as well. The report describes the data and statistical methods used to construct the EPI for corn refining plants. Individual equations are presented, as are the instructions for using them in an associated Excel spreadsheet.

Boyd, G. A.; Decision and Information Sciences; USEPA

2006-07-31T23:59:59.000Z

162

Priorities for Corrosion Research and Development for the Electric Power Industry  

Science Conference Proceedings (OSTI)

This report identifies the specific corrosion problems that result in the largest costs to the electric power industry. It describes the corrosion-related research and development (R&D) that is underway to address these problems and also discusses additional R&D that appears warranted. The report discusses several high-cost areas where new research is judged to be unnecessary as the problems are well understood, but where improved application of already available technology seems important.

2002-09-09T23:59:59.000Z

163

Continuation of Research, Commercialization, and Workforce Development in the Polymer/Electronics Recycling Industry  

Science Conference Proceedings (OSTI)

The MARCEE Project was established to understand the problems associated with electronics recycling and to develop solutions that would allow an electronics recycling industry to emerge. While not all of the activities have been funded by MARCEE, but through private investment, they would not have occurred had the MARCEE Project not been undertaken. The problems tackled and the results obtained using MARCEE funds are discussed in detail in this report.

Mel Croucher; Rakesh Gupta; Hota GangaRao; Darran Cairns; Jinzing Wang; Xiaodong Shi; Jason Linnell; Karen Facemyer; Doug Ritchie; Jeff Tucker

2009-09-30T23:59:59.000Z

164

Optoelectronic devices utilizing materials having enhanced electronic transitions  

Science Conference Proceedings (OSTI)

An optoelectronic device that includes a material having enhanced electronic transitions. The electronic transitions are enhanced by mixing electronic states at an interface. The interface may be formed by a nano-well, a nano-dot, or a nano-wire.

Black, Marcie R. (Newton, MA)

2011-02-22T23:59:59.000Z

165

Optoelectronic devices utilizing materials having enhanced electronic transitions  

DOE Patents (OSTI)

An optoelectronic device that includes a material having enhanced electronic transitions. The electronic transitions are enhanced by mixing electronic states at an interface. The interface may be formed by a nano-well, a nano-dot, or a nano-wire.

Black, Marcie R.

2013-04-09T23:59:59.000Z

166

Organic photosensitive optoelectronic device having a phenanthroline exciton blocking layer  

DOE Patents (OSTI)

An organic photosensitive optoelectronic device, having an anode, a cathode, and an organic blocking layer between the anode and the cathode is described, wherein the blocking layer comprises a phenanthroline derivative, and at least partially blocks at least one of excitons, electrons, and holes.

Thompson, Mark E. (Anaheim Hills, CA); Li, Jian (Los Angeles, CA); Forrest, Stephen (Princeton, NJ); Rand, Barry (Princeton, NJ)

2011-02-22T23:59:59.000Z

167

(Development of industrial processes for manufacturing of silicon sampling hadron calorimeters)  

SciTech Connect

The travelers attended meetings in Dubna and in Zelenograd. Discussions in Dubna centered on (1) obtaining information on USSR capabilities in silicon detector manufacture and testing and on (2) strategy regarding the development of an industrial process and the manufacture of a large quantity of silicon detectors for the SSC L* collaboration. The ELMA plant in Zelenograd was inspected, and discussions were held on production process development and on a possible detector supply time line. In addition, J. Walter participated in technical and cost estimate forecast discussions with representatives of Wacker-Chemitronic Factory (Germany) about silicon crystals for possible use in the SSC.

Plasil, F.; Walter, J.

1991-01-04T23:59:59.000Z

168

Steam Challenge: Developing A New DOE Program to Help Industry be Steam Smart  

E-Print Network (OSTI)

Last year, the Alliance to Save Energy, the Department of Energy's Office of Industrial Technologies, and a cadre of private companies and associations formed an innovative "Steam Partnership" with the goal of developing a new, DOE technical assistance program on steam efficiency. In 1997, the Steam Partnership began to define the appropriate activities, tools, and services of a public-private program on steam. Modeled after the successful Motor Challenge program and the newly launched Compressed Air Challenge program, "Steam Challenge" will highlight the importance of steam system efficiency and provide information and technical assistance on technologies for today's industrial steam systems. This paper will introduce Steam Challenge, describe what has been accomplished over the last year, and describe the program's future goals and activities.

Jones, T.; Hart, F.

1998-04-01T23:59:59.000Z

169

The Paradox of Regulatory Development in China: The Case of the Electricity Industry  

E-Print Network (OSTI)

supply to attract investment in the energy-intensive industries.industry to secure a stable supply of raw materials. In 2006, Huaneng Energy andsupply enables the local government to attract energy-intensive, heavy industries

Tsai, Chung-min

2010-01-01T23:59:59.000Z

170

The Paradox of Regulatory Development in China: The Case of the Electricity Industry  

E-Print Network (OSTI)

2006). Beijing: China Electric Power Press. Zhu, Chengzhang.reform in the Chinese electric power industry). ? Zhongguoand Challenges for Chinas Electric Power Industry. ? The

Tsai, Chung-min

2010-01-01T23:59:59.000Z

171

Gallium-Nitride Transistors for High-Efficiency Industrial Power Supplies, Phase 1: State of Semiconductor Development and Industrial Power Supply Market  

Science Conference Proceedings (OSTI)

This white paper describes recent advancements in the development of Gallium-Nitride (GaN) transistors for power conversion applications. This wide bandgap semiconductor has the potential to reduce losses and improve performance of power converters. The industrial power supply market is described and the application of GaN to power conversion in this segment is introduced for future work.

2013-12-23T23:59:59.000Z

172

Lessons Learned from the U.S. Photovoltaic Industry and Implications for Development of Distributed Small Wind: Preprint  

DOE Green Energy (OSTI)

In recent years, advocates for the solar photovoltaic (PV) industry have developed successful strategies for marketing PV as a customer-sited energy resource. Their efforts have ranged from supporting effective Federal programs and incentives to initiating state and local efforts to remove siting barriers and industry efforts that build consumer confidence. More important, PV advocates have established relationships that define customer-sited PV as a viable and important technology. The PV industry's record of success and its persistent challenges can be instructive to the small wind industry. These industries share many characteristics in terms of system outputs, applications, economics, and industry goals. In some ways, small wind is staged for growth just as PV was a decade ago. The authors provide an examination of market development issues in these industries, including Federal policy infrastructure and incentives, state and local policy infrastructure, and business support. Subsequently, the authors provide recommendations for distributed wind development that include collaborations with the PV industry and as stand-alone small wind initiatives. In particular, the authors suggest aligning customer-sited small wind (and PV) with demand-side energy strategies and emphasizing the need to address all customer-sited renewables under a cohesive distributed generation development strategy.

Forsyth, T.; Tombari, C.; Nelson, M.

2006-06-01T23:59:59.000Z

173

Lessons Learned from the U.S. Photovoltaic Industry and Implications for Development of Distributed Small Wind: Preprint  

SciTech Connect

In recent years, advocates for the solar photovoltaic (PV) industry have developed successful strategies for marketing PV as a customer-sited energy resource. Their efforts have ranged from supporting effective Federal programs and incentives to initiating state and local efforts to remove siting barriers and industry efforts that build consumer confidence. More important, PV advocates have established relationships that define customer-sited PV as a viable and important technology. The PV industry's record of success and its persistent challenges can be instructive to the small wind industry. These industries share many characteristics in terms of system outputs, applications, economics, and industry goals. In some ways, small wind is staged for growth just as PV was a decade ago. The authors provide an examination of market development issues in these industries, including Federal policy infrastructure and incentives, state and local policy infrastructure, and business support. Subsequently, the authors provide recommendations for distributed wind development that include collaborations with the PV industry and as stand-alone small wind initiatives. In particular, the authors suggest aligning customer-sited small wind (and PV) with demand-side energy strategies and emphasizing the need to address all customer-sited renewables under a cohesive distributed generation development strategy.

Forsyth, T.; Tombari, C.; Nelson, M.

2006-06-01T23:59:59.000Z

174

Lessons Learned from the U.S. Photovoltaic Industry and Implications for Development of Distributed Small Wind  

Science Conference Proceedings (OSTI)

In recent years, advocates for the solar photovoltaic (PV) industry have developed successful strategies for marketing PV as a customer-sited energy resource. Their efforts have ranged from supporting effective Federal programs and incentives to initiating state and local efforts to remove siting barriers and industry efforts that build consumer confidence. More important, PV advocates have established relationships that define customer-sited PV as a viable and important technology. The PV industry's record of success and its persistent challenges can be instructive to the small wind industry. These industries share many characteristics in terms of system outputs, applications, economics, and industry goals. In some ways, small wind is staged for growth just as PV was a decade ago. The authors provide an examination of market development issues in these industries, including Federal policy infrastructure and incentives, state and local policy infrastructure, and business support. Subsequently, the authors provide recommendations for distributed wind development that include collaborations with the PV industry and as stand-alone small wind initiatives. In particular, the authors suggest aligning customer-sited small wind (and PV) with demand-side energy strategies and emphasizing the need to address all customer-sited renewables under a cohesive distributed generation development strategy.

Forsyth, T.; Tombari, C.; Nelson, M.

2006-01-01T23:59:59.000Z

175

Chapter 18: Understanding the Developing Cellulosic Biofuels Industry through Dynamic Modeling  

DOE Green Energy (OSTI)

The purpose of this chapter is to discuss a system dynamics model called the Biomass Scenario Model (BSM), which is being developed by the U.S. Department of Energy as a tool to better understand the interaction of complex policies and their potential effects on the burgeoning cellulosic biofuels industry in the United States. The model has also recently been expanded to include advanced conversion technologies and biofuels (i.e., conversion pathways that yield biomass-based gasoline, diesel, jet fuel, and butanol), but we focus on cellulosic ethanol conversion pathways here. The BSM uses a system dynamics modeling approach (Bush et al., 2008) built on the STELLA software platform.

Newes, E.; Inman, D.; Bush, B.

2011-01-01T23:59:59.000Z

176

MSTC - Microsystems Science, Technology, and Components - Optoelectron...  

NLE Websites -- All DOE Office Websites (Extended Search)

researched, developed and delivered include a wide variety of specialty semiconductor lasers; integrated VCSEL-RCPD circuits (vertical-cavity surface-emitting lasers,...

177

Effective policymaking for developing ICT industries : lessons from three African governments' approach to information and communications technology  

E-Print Network (OSTI)

This thesis studies the effect of different information and communication technology (ICT) policies on the performance of the ICT industry in a given country. Many developing country governments are in the process of ...

Watkins, Kristen D

2012-01-01T23:59:59.000Z

178

Research, Commercialization, & Workforce Development in the Polymer/Electronics Recycling Industry  

Science Conference Proceedings (OSTI)

The Mid-Atlantic Recycling Center for End-of-Life Electronics (MARCEE) was set up in 1999 in response to a call from Congressman Alan Mollohan, who had a strong interest in this subject. A consortium was put together which included the Polymer Alliance Zone (PAZ) of West Virginia, West Virginia University (WVU), DN American and Ecolibrium. The consortium developed a set of objectives and task plans, which included both the research issues of setting up facilities to demanufacture End-of-Life Electronics (EoLE), the economics of the demanufacturing process, and the infrastructure development necessary for a sustainable recycling industry to be established in West Virginia. This report discusses the work of the MARCEE Project Consortium from November 1999 through March 2005. While the body of the report is distributed in hard-copy form the Appendices are being distributed on CD's.

Carl Irwin; Rakesh Gupta; Richard Turton; GangaRao Hota; Cyril Logar; Tom Ponzurick; Buddy Graham; Walter Alcorn; Jeff Tucker

2006-02-01T23:59:59.000Z

179

An Industrial-Based Consortium to Develop Premium Carbon Products from Coal Final Report - Part 2  

Science Conference Proceedings (OSTI)

Since 1998, The Pennsylvania State University successfully managed the Consortium for Premium Carbon Products from Coal (CPCPC), which was a vehicle for industry-driven research on the promotion, development, and transfer of innovative technologies on premium carbon products from coal to the U.S. industry. The CPCPC was an initiative led by Penn State, its cocharter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provided the base funding for the program, with Penn State responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity continued under cooperative agreement No. DE-FC26-03NT41874, which started October 1, 2003 and ended December 31, 2010. The objective of the second agreement was to continue the successful operation of the CPCPC. The CPCPC enjoyed tremendous success with its organizational structure, which included Penn State and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC was its industry-led council that selected proposals submitted by CPCPC members to ensure CPCPC target areas had strong industrial support. CPCPC had 58 member companies and universities engaged over the 7-year period of this contract. Members were from 17 states and five countries outside of the U.S. During this period, the CPCPC Executive Council selected 46 projects for funding. DOE/CPCPC provided $3.9 million in funding or an average of $564,000 per year. The total project costs were $5.45 million with $1.5 million, or ~28% of the total, provided by the members as cost share. Total average project size was $118,000 with $85,900 provided by DOE/CPCPC. In addition to the research, technology transfer/outreach was a large component of CPCPC's activities. Efficient technology transfer was critical for the deployment of new technologies into the field. CPCPC organized and hosted technology transfer meetings, tours, and tutorials, attended outreach conferences and workshops to represent CPCPC and attract new members, prepared and distributed reports and publications, and developed and maintained a Web site. The second contract ended December 31, 2010, and it is apparent that CPCPC positively impacted the carbon industry and coal research. Statistics and information were compiled to provide a comprehensive account of the impact the consortium had and the beneficial outcomes of many of the individual projects. Project fact sheet, success stories, and other project information were prepared. Two topical reports, a Synthesis report and a Web report, were prepared detailing this information.

Miller, Bruce; Winton, Shea

2010-12-31T23:59:59.000Z

180

An Industrial-Based Consortium to Develop Premium Carbon Products from Coal Final Report - Part 5  

Science Conference Proceedings (OSTI)

Since 1998, The Pennsylvania State University successfully managed the Consortium for Premium Carbon Products from Coal (CPCPC), which was a vehicle for industry-driven research on the promotion, development, and transfer of innovative technologies on premium carbon products from coal to the U.S. industry. The CPCPC was an initiative led by Penn State, its cocharter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provided the base funding for the program, with Penn State responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity continued under cooperative agreement No. DE-FC26-03NT41874, which started October 1, 2003 and ended December 31, 2010. The objective of the second agreement was to continue the successful operation of the CPCPC. The CPCPC enjoyed tremendous success with its organizational structure, which included Penn State and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC was its industry-led council that selected proposals submitted by CPCPC members to ensure CPCPC target areas had strong industrial support. CPCPC had 58 member companies and universities engaged over the 7-year period of this contract. Members were from 17 states and five countries outside of the U.S. During this period, the CPCPC Executive Council selected 46 projects for funding. DOE/CPCPC provided $3.9 million in funding or an average of $564,000 per year. The total project costs were $5.45 million with $1.5 million, or {approx}28% of the total, provided by the members as cost share. Total average project size was $118,000 with $85,900 provided by DOE/CPCPC. In addition to the research, technology transfer/outreach was a large component of CPCPC's activities. Efficient technology transfer was critical for the deployment of new technologies into the field. CPCPC organized and hosted technology transfer meetings, tours, and tutorials, attended outreach conferences and workshops to represent CPCPC and attract new members, prepared and distributed reports and publications, and developed and maintained a Web site. The second contract ended December 31, 2010, and it is apparent that CPCPC positively impacted the carbon industry and coal research. Statistics and information were compiled to provide a comprehensive account of the impact the consortium had and the beneficial outcomes of many of the individual projects. Project fact sheet, success stories, and other project information were prepared. Two topical reports, a Synthesis report and a Web report, were prepared detailing this information.

Miller, Bruce; Shea, Winton

2010-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

An Industrial-Based Consortium to Develop Premium Carbon Products from Coal Final Report - Part 1  

Science Conference Proceedings (OSTI)

Since 1998, The Pennsylvania State University successfully managed the Consortium for Premium Carbon Products from Coal (CPCPC), which was a vehicle for industry-driven research on the promotion, development, and transfer of innovative technologies on premium carbon products from coal to the U.S. industry. The CPCPC was an initiative led by Penn State, its cocharter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provided the base funding for the program, with Penn State responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity continued under cooperative agreement No. DE-FC26-03NT41874, which started October 1, 2003 and ended December 31, 2010. The objective of the second agreement was to continue the successful operation of the CPCPC. The CPCPC enjoyed tremendous success with its organizational structure, which included Penn State and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC was its industry-led council that selected proposals submitted by CPCPC members to ensure CPCPC target areas had strong industrial support. CPCPC had 58 member companies and universities engaged over the 7-year period of this contract. Members were from 17 states and five countries outside of the U.S. During this period, the CPCPC Executive Council selected 46 projects for funding. DOE/CPCPC provided $3.9 million in funding or an average of $564,000 per year. The total project costs were $5.45 million with $1.5 million, or ~28% of the total, provided by the members as cost share. Total average project size was $118,000 with $85,900 provided by DOE/CPCPC. In addition to the research, technology transfer/outreach was a large component of CPCPC's activities. Efficient technology transfer was critical for the deployment of new technologies into the field. CPCPC organized and hosted technology transfer meetings, tours, and tutorials, attended outreach conferences and workshops to represent CPCPC and attract new members, prepared and distributed reports and publications, and developed and maintained a Web site. The second contract ended December 31, 2010, and it is apparent that CPCPC positively impacted the carbon industry and coal research. Statistics and information were compiled to provide a comprehensive account of the impact the consortium had and the beneficial outcomes of many of the individual projects. Project fact sheet, success stories, and other project information were prepared. Two topical reports, a Synthesis report and a Web report, were prepared detailing this information.

Miller, Bruce; Winton, Shea

2010-12-31T23:59:59.000Z

182

An Industrial-Based Consortium to Develop Premium Carbon Products from Coal Final Report - Part 3  

Science Conference Proceedings (OSTI)

Since 1998, The Pennsylvania State University successfully managed the Consortium for Premium Carbon Products from Coal (CPCPC), which was a vehicle for industry-driven research on the promotion, development, and transfer of innovative technologies on premium carbon products from coal to the U.S. industry. The CPCPC was an initiative led by Penn State, its cocharter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provided the base funding for the program, with Penn State responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity continued under cooperative agreement No. DE-FC26-03NT41874, which started October 1, 2003 and ended December 31, 2010. The objective of the second agreement was to continue the successful operation of the CPCPC. The CPCPC enjoyed tremendous success with its organizational structure, which included Penn State and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC was its industry-led council that selected proposals submitted by CPCPC members to ensure CPCPC target areas had strong industrial support. CPCPC had 58 member companies and universities engaged over the 7-year period of this contract. Members were from 17 states and five countries outside of the U.S. During this period, the CPCPC Executive Council selected 46 projects for funding. DOE/CPCPC provided $3.9 million in funding or an average of $564,000 per year. The total project costs were $5.45 million with $1.5 million, or ~28% of the total, provided by the members as cost share. Total average project size was $118,000 with $85,900 provided by DOE/CPCPC. In addition to the research, technology transfer/outreach was a large component of CPCPC's activities. Efficient technology transfer was critical for the deployment of new technologies into the field. CPCPC organized and hosted technology transfer meetings, tours, and tutorials, attended outreach conferences and workshops to represent CPCPC and attract new members, prepared and distributed reports and publications, and developed and maintained a Web site. The second contract ended December 31, 2010, and it is apparent that CPCPC positively impacted the carbon industry and coal research. Statistics and information were compiled to provide a comprehensive account of the impact the consortium had and the beneficial outcomes of many of the individual projects. Project fact sheet, success stories, and other project information were prepared. Two topical reports, a Synthesis report and a Web report, were prepared detailing this information.

Miller, Bruce; Shea, Winton

2010-12-31T23:59:59.000Z

183

An Industrial-Based Consortium to Develop Premium Carbon Products from Coal Final Report - Part 4  

Science Conference Proceedings (OSTI)

Since 1998, The Pennsylvania State University successfully managed the Consortium for Premium Carbon Products from Coal (CPCPC), which was a vehicle for industry-driven research on the promotion, development, and transfer of innovative technologies on premium carbon products from coal to the U.S. industry. The CPCPC was an initiative led by Penn State, its cocharter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provided the base funding for the program, with Penn State responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity continued under cooperative agreement No. DE-FC26-03NT41874, which started October 1, 2003 and ended December 31, 2010. The objective of the second agreement was to continue the successful operation of the CPCPC. The CPCPC enjoyed tremendous success with its organizational structure, which included Penn State and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC was its industry-led council that selected proposals submitted by CPCPC members to ensure CPCPC target areas had strong industrial support. CPCPC had 58 member companies and universities engaged over the 7-year period of this contract. Members were from 17 states and five countries outside of the U.S. During this period, the CPCPC Executive Council selected 46 projects for funding. DOE/CPCPC provided $3.9 million in funding or an average of $564,000 per year. The total project costs were $5.45 million with $1.5 million, or {approx}28% of the total, provided by the members as cost share. Total average project size was $118,000 with $85,900 provided by DOE/CPCPC. In addition to the research, technology transfer/outreach was a large component of CPCPC's activities. Efficient technology transfer was critical for the deployment of new technologies into the field. CPCPC organized and hosted technology transfer meetings, tours, and tutorials, attended outreach conferences and workshops to represent CPCPC and attract new members, prepared and distributed reports and publications, and developed and maintained a Web site. The second contract ended December 31, 2010, and it is apparent that CPCPC positively impacted the carbon industry and coal research. Statistics and information were compiled to provide a comprehensive account of the impact the consortium had and the beneficial outcomes of many of the individual projects. Project fact sheet, success stories, and other project information were prepared. Two topical reports, a Synthesis report and a Web report, were prepared detailing this information.

Miller, Bruce; Shea, Winton

2010-12-31T23:59:59.000Z

184

RIR-MAPLE deposition of conjugated polymers and hybrid nanocomposites for application to optoelectronic devices  

SciTech Connect

Resonant infrared matrix-assisted pulsed laser evaporation (RIR-MAPLE) is a variation of pulsed laser deposition that is useful for organic-based thin films because it reduces material degradation by selective absorption of infrared radiation in the host matrix. A unique emulsion-based RIR-MAPLE approach has been developed that reduces substrate exposure to solvents and provides controlled and repeatable organic thin film deposition. In order to establish emulsion-based RIR-MAPLE as a preferred deposition technique for conjugated polymer or hybrid nanocomposite optoelectronic devices, studies have been conducted to demonstrate the value added by the approach in comparison to traditional solution-based deposition techniques, and this work will be reviewed. The control of hybrid nanocomposite thin film deposition, and the photoconductivity in such materials deposited using emulsion-based RIR-MAPLE, will also be reviewed. The overall result of these studies is the demonstration of emulsion-based RIR-MAPLE as a viable option for the fabrication of conjugated polymer and hybrid nanocomposite optoelectronic devices that could yield improved device performance.

Stiff-Roberts, Adrienne D.; Pate, Ryan; McCormick, Ryan; Lantz, Kevin R. [Department of Electrical and Computer Engineering, Duke University Box 90291, Durham, NC 27708-0291, 919-660-5560 (United States)

2012-07-30T23:59:59.000Z

185

3rd International Conference on Sustainable Development Indicators 495 in the Minerals Industry, June 2007, Milos island, Greece  

E-Print Network (OSTI)

to develop a process for stake- holder education and engagement in sustainable energy. 1. INTRODUCTION 1 the release of greenhouse gases and the development of sustainable energy technologies. Figure 2: U.S. DOE3rd International Conference on Sustainable Development Indicators 495 in the Minerals Industry

186

Assessment of industry needs for oil shale research and development. Final report  

SciTech Connect

Thirty-one industry people were contacted to provide input on oil shale in three subject areas. The first area of discussion dealt with industry`s view of the shape of the future oil shale industry; the technology, the costs, the participants, the resources used, etc. It assessed the types and scale of the technologies that will form the industry, and how the US resource will be used. The second subject examined oil shale R&D needs and priorities and potential new areas of research. The third area of discussion sought industry comments on what they felt should be the role of the DOE (and in a larger sense the US government) in fostering activities that will lead to a future commercial US oil shale shale industry.

Hackworth, J.H.

1987-05-01T23:59:59.000Z

187

Therapeutic Ultrasound Research And Development From An Industrial And Commercial Perspective  

Science Conference Proceedings (OSTI)

The objective of this paper is to share the challenges and opportunities as viewed from an industrial and commercial perspective that one encounters when performing therapeutic ultrasound research, development, manufacturing, and sales activities. Research in therapeutic ultrasound has become an active field in the last decade, spurred by technological advances in the areas of transducer materials, control electronics, treatment monitoring techniques, an ever increasing number of clinical applications, and private and governmental funding opportunities. The development of devices and methods utilizing therapeutic ultrasound to cure or manage disease is being pursued by startup companies and large established companies alike, driven by the promise of profiting at many levels from this new and disruptive technology. Widespread penetration within the clinical community remains elusive, with current approaches focusing on very specific applications and niche markets. Challenges include difficulties in securing capital to develop the technology and undertake costly clinical trials, a regulatory landscape that varies from country to country, resistance from established practitioners, and difficulties in assembling a team with the right mix of technological savvy and business expertise. Success is possible and increasing, however, as evidenced by several companies, initiatives, and products with measurable benefits to the patient, clinician, and companies alike.

Seip, Ralf [Philips Research, 345 Scarborough Road, Briarcliff Manor, NY 10510 (United States)

2009-04-14T23:59:59.000Z

188

Development and evaluation of a workpiece temperature analyzer (WPTA) for industrial furances (Phase 1)  

Science Conference Proceedings (OSTI)

This project is directed toward the research, development, and evaluation of a viable commercial product-a workpiece temperature measurement analyzer (WPTA) for fired furnaces based on unique radiation properties of surfaces. This WPTA will provide for more uniform, higher quality products and reduce product rejects as well as permit the optimum use of energy. The WPTA may also be utilized in control system applications including metal heat treating, forging furnaces, and ceramic firing furnaces. A large market also exists in the chemical process and refining industry. WPTA applications include the verification of product temperature/time cycles, and use as a front-end sensor for automatic feedback control systems. This report summarizes the work performed in Phase 1 of this three-phase project. The work Phase 1 included the application evaluation; the evaluation of present technologies and limitations; and the development of a preliminary conceptual WPTA design, including identification of technical and economic benefits. Recommendations based on the findings of this report include near-term enhancement of the capabilities of the Pyrolaser, and long-term development of an instrument based on Raman Spectroscopy. Development of the Pyrofiber, fiberoptics version of the Pyrolaser, will be a key to solving present problems involving specularity, measurement angle, and costs of multipoint measurement. Extending the instrument's measurement range to include temperatures below 600{degrees}C will make the product useful for a wider range of applications. The development of Raman Spectroscopy would result in an instrument that could easily be adapted to incorporate a wealth of additional nondestructive analytical capabilities, including stress/stain indication, crystallography, species concentrations, corrosion studies, and catalysis studies, in addition to temperature measurement. 9 refs., 20 figs., 16 tabs.

Not Available

1991-10-01T23:59:59.000Z

189

Industry participation in DOE-sponsored geopressured geothermal resource development. Final report, 1 September 1977-30 April 1979  

DOE Green Energy (OSTI)

A series of DOE/Industry forums were carried out to keep industry advised of the DOE program to develop the geopressured geothermal resources of the Gulf Coast. A total of eighteen meetings were held with registered attendance of 621 representing a good cross section of industry, state, and federal agencies. An Overview Group and four working subgroups - site selection, drilling and testing, environmental/laboratory research, and legal institutional were established to subdivide the DOE programs into areas of interest and expertise. During the contract period three overview, four site selection, three drilling and testing, five environmental/laboratory research and three legal/institutional meetings have been conducted. Interest in and attendance at the meetings continue to grow reflecting increased industry contact with the DOE Geopressured Geothermal Resource Development Program. Two other studies were carried out for DOE under this contract; a Salt Water Disposal Study and an Industry Survey to evaluate the DOE Resource Development Program. The Salt Water Disposal Study reviewed subsurface salt water disposal experience on the Texas and Louisiana Gulf Coast. This preliminary study concluded that subsurface brine disposal should be possible in the areas of interest with adequate evaluation of the geology of each area and a well designed and constructed surface and subsurface facility. The industry survey indicated general satisfaction with the technical design of the resource evaluation program but felt the program should be moving faster.

Coffer, H.F.

1979-01-01T23:59:59.000Z

190

Opto-Electronics in Large Array Gas Detector Systems  

E-Print Network (OSTI)

Large array gas detector systems are used in particle and nuclear physics experiments involving high-energy nucleon-nucleon and heavy-ion collisions. We have observed that in large array gas detector systems the momentary discharges inside the detector cells result in slowdown of High Voltage conditioning and possible hindrances in signal processing. We have explored the opto-electronic devices like the opto-coupler, optical fibre and signal processing circuit, which provide successful monitoring procedures and preventive measures to overcome the challenges produced in such complex detector systems.

M. R. Dutta Majumdar; Debasish Das; Tapan K. Nayak

2005-12-23T23:59:59.000Z

191

DEVELOPMENT AND DEMONSTRATION OF NOVEL LOW-NOx BURNERS IN THE STEEL INDUSTRY  

Science Conference Proceedings (OSTI)

Gas Technology Institute (GTI), together with Hamworthy Peabody Combustion Incorporated (formerly Peabody Engineering Corporation), the University of Utah, and Far West Electrochemical have developed and demonstrated an innovative combustion system suitable for natural gas and coke-oven gas firing within the steel industry. The combustion system is a simple, low-cost, energy-efficient burner that can reduce NOx by more than 75%. The U.S. steel industry needs to address NOx control at its steelmaking facilities. A significant part of NOx emissions comes from gas-fired boilers. In steel plants, byproduct gases blast furnace gas (BFG) and coke-oven gas (COG) are widely used together with natural gas to fire furnaces and boilers. In steel plants, natural gas can be fired together with BFG and COG, but, typically, the addition of natural gas raises NOx emissions, which can already be high because of residual fuel-bound nitrogen in COG. The Project Team has applied its expertise in low-NOx burners to lower NOx levels for these applications by combining advanced burner geometry and combustion staging with control strategies tailored to mixtures of natural gas and byproduct fuel gases. These methods reduce all varieties of NOx thermal NOx produced by high flame temperatures, prompt NOx produced by complex chain reactions involving radical hydrocarbon species and NOx from fuel-bound nitrogen compounds such as ammonia found in COG. The Project Team has expanded GTIs highly successful low-NOx forced internal recirculation (FIR) burner, previously developed for natural gas-fired boilers, into facilities that utilize BFG and COG. For natural gas firing, these burners have been shown to reduce NOx emissions from typical uncontrolled levels of 80-100 vppm to single-digit levels (9 vppm). This is done without the energy efficiency penalties incurred by alternative NOx control methods, such as external flue gas recirculation (FGR), water injection, and selective non-catalytic reduction. The FIR burner was previously demonstrated on firetube and watertube boilers, and these units are still operating at several industrial and commercial boiler sites in sizes ranging from 2.5 to 60 million Btu/h. This report covers the development of an innovative combustion system suitable for natural gas or coke-oven gas firing within the steel industry. The prototype FIR burner was evaluated on a 20 million Btu/h watertube boiler. Acceptable burner performance was obtained when firing natural gas and simulated coke-oven gas doped with ammonia. The laboratory data reveals a direct relationship between NOx formation and the ammonia concentration in the fuel. In addition, NOx formation increases as the primary stoichiometric ratio (PSR) increases. Representative ammonia concentrations, as documented in the steel industry, ranged from 200 to 500 vppm. When the laboratory burner/boiler was operated with 500 vppm ammonia in the fuel, NOx emissions ranged from 50 to 75 vppm. This, conservatively, is 75% less than state-of-the-art burner performance. When the burner is operated with 200 vppm ammonia in the fuel, the corresponding NOx emissions would range from 30 to 45 vppm, 84% less than present burner technology. During field evaluation on a 174 million Btu/h industrial prototype burner both natural gas and actual COG from on-site generation were tested. Despite the elevated hydrogen cyanide and ammonia content in the COG throughout the test program, the FIR burner showed an improvement over baseline emissions. At full load; 167 million Btu/h, NOx emissions were relatively low at 169 vppm. This represents a 30% reduction compared to baseline emissions not accounting for the higher hydrogen cyanide content in the COG. CO emissions remained below 20 vppm and were stable across the firing range. This represents a 68% reduction compared to baseline CO emissions. When firing natural gas, emissions were stable as firing rate increased over the range. At low fire; 45 million Btu/h, NOx emissions where 33 vppm and increased at full load; 144 million Btu

Cygan, David

2006-12-28T23:59:59.000Z

192

JOINT-INDUSTRY PARTNERSHIP TO DEVELOP A HOLLOW SPHERE DUAL-GRADIENT DRILLING SYSTEM  

Science Conference Proceedings (OSTI)

Maurer Technology Inc. (MTI) formed a joint-industry partnership to fund the development of a hollow sphere dual-gradient drilling (DGD) system. Phase I consisted of collecting, compiling, analyzing, and distributing information and data regarding a new DGD system for use by the oil and gas industry. Near the end of Phase I, DOE provided funding to the project that was used to conduct a series of critical follow-on tests investigating sphere separation in weighted waterbase and oilbase muds. Drilling costs in deep water are high because seawater pressure on the ocean floor creates a situation where many strings of casing are required due to the relatively close spacing between fracture and pore pressure curves. Approximately $100 million have been spent during the past five years on DGD systems that place pumps on the seafloor to reduce these drilling problems by reducing the annulus fluid pressure at the bottom of the riser. BP estimates that a DGD system can save $9 million per well in the Thunderhorse Field and Conoco estimates it can save $5 to $15 million per well in its deepwater operations. Unfortunately, previous DGD development projects have been unsuccessful due to the high costs ($20 to $50 million) and reliability problems with seafloor pump systems. MTI has been developing a simple DGD system concept that would pump hollow glass spheres into the bottom of the riser to reduce density of the mud in the riser. This eliminates the requirement for seafloor pumps and replaces them with low cost mud pumps, shale shakers, and other oilfield equipment that can be operated on the rig by conventional crews. A $1.8 million Phase I joint-industry project funded by five service companies and three operators showed that hollow spheres could be pumped well, but difficulties were encountered in separating the spheres from a polymer mud supplied by Halliburton due to the high viscosity of this mud at the low shear rates encountered on oilfield shale shaker screens. As a result, an excessive amount of this polymer mud flowed across the screen with the beads instead of through the screen. At the completion of the Phase I project, it was concluded that the hollow sphere system would not work effectively with the polymer mud tested. ExxonMobil and Shell engineers proposed that additional sphere separation tests needed to be conducted with weighted oilfield waterbase and oilbase muds to determine if the DGD system would work with these muds. The DOE agreed to provide a $200,000 grant for these tests. The DOE-funded tests, described in this report, showed that the spheres could be pumped with conventional oilfield centrifugal and triplex mud pumps and separated effectively from both oilfield waterbase and oilbase muds using conventional oilfield shale shakers and hydrocyclones. As a result of the success of these DOE tests, this DGD system is ready for full-scale field testing, first on land wells and later in the offshore environment. Maurer Technology Inc. is currently proposing a Phase II project to oil companies to further develop this DGD concept. This project would be funded by four to eight operators. If Phase II tests are successful, Noble plans to commercialize this system with a service company partner that will market and operate the DGD system on Noble's and other drilling contractors' rigs.

William C. Maurer; Colin Ruan; Greg Deskins

2003-05-01T23:59:59.000Z

193

A Value Proposition for Developing an Industry Database for High Voltage Circuit Breakers & CIM Data Objects for T&D  

Science Conference Proceedings (OSTI)

EPRI initiated work to develop databases for performance analysis and benchmarking in order to address issues of performance data availability, support industry efforts to maximize power delivery asset values, and optimize maintenance activities. With the successful development of an industrywide database for distribution cables and the extension of that work to power transformers, interest has turned to high-voltage circuit breakers (HVCBs).

2007-11-19T23:59:59.000Z

194

Demand Management Demonstration Project, Stage 5: development of industrial load simulation model. Executive summary. Final report  

SciTech Connect

The purpose of this project was to design, develop, test and document a computer simulation model of electric utility generating costs required to meet industrial power demands and the effects of utility load management on these generating costs. The results showed that the model developed is a well conceived load management testing, marginal costing tool. What if situations can be readily tested to determine their impact on system profile and short run marginal costs. The terms unshaped and shaped refer to customers or system use patterns before and after some load management technique was tested. The total flexibility of the model is only apparent after the user has studied test runs in detail. Hourly marginal costs reveal many unexpected changes as a result of shaping loads. Other unexpected changes due to varying economic dispatch schedules while shaping, illustrate the unprecedental latitude for the user to explore optimum generation and load management combinations. The general concept of the model is depicted in the flow chart on the next page.

1977-04-01T23:59:59.000Z

195

The Paradox of Regulatory Development in China: The Case of the Electricity Industry  

E-Print Network (OSTI)

zhongguo dianli chanye (Chinas Electricity Industry at themulti_page.pdf. State Electricity Regulatory Commission.The Annual Report on Electricity Regulation (2006). Beijing:

Tsai, Chung-min

2010-01-01T23:59:59.000Z

196

The Paradox of Regulatory Development in China: The Case of the Electricity Industry  

E-Print Network (OSTI)

industry and suggest electricity tariff rates to the Stateof the ?coal-electricity tariff automatic mechanism? (designed the coal-electricity tariff automatic mechanism in

Tsai, Chung-min

2010-01-01T23:59:59.000Z

197

Development of Optimal Energy Infrastructures for the Oil Sands Industry in a CO?-constrained World.  

E-Print Network (OSTI)

??Western Canadian bitumen is becoming a predominant source of energy for North American markets. The bitumen extraction and upgrading processes in the oil sands industry (more)

Ordorica Garcia, Jesus Guillermo

2007-01-01T23:59:59.000Z

198

The Paradox of Regulatory Development in China: The Case of the Electricity Industry  

E-Print Network (OSTI)

industry, such as rising coal prices and rigid electricityagainst soaring coal prices, the central government designedadjustment of power prices when coal prices increase more

Tsai, Chung-min

2010-01-01T23:59:59.000Z

199

Developing a generic hazard analysis critical control point (HACCP) system for the wheat milling industry.  

E-Print Network (OSTI)

??In South Africa there is a need within the milling industry for controlling food safety especially due to customer's demands and government's regulations. The best (more)

Gillion, Lauren

2005-01-01T23:59:59.000Z

200

Method of fabricating an optoelectronic device having a bulk heterojunction  

DOE Patents (OSTI)

A method of fabricating an organic optoelectronic device having a bulk heterojunction comprises the steps of: depositing a first layer over a first electrode by organic vapor phase deposition, wherein the first layer comprises a first organic small molecule material; depositing a second layer on the first layer such that the second layer is in physical contact with the first layer, wherein the interface of the second layer on the first layer forms a bulk heterojunction; and depositing a second electrode over the second layer to form the optoelectronic device. In another embodiment, a first layer having protrusions is deposited over the first electrode, wherein the first layer comprises a first organic small molecule material. For example, when the first layer is an electron donor layer, the first electrode is an anode, the second layer is an electron acceptor layer, and the second electrode is a cathode. As a further example, when the first layer is an electron acceptor layer, the first electrode is a cathode, the second layer is an electron donor layer, and the second electrode is an anode.

Shtein, Max (Princeton, NJ); Yang, Fan (Princeton, NJ); Forrest, Stephen R. (Princeton, NJ)

2008-09-02T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Cogeneration for industrial and mixed-use parks. Volume 3. A guide for park developers, owners, and tenants. Final report  

SciTech Connect

Using cogeneration in mixed-use and industrial parks can cut energy costs ad smooth out peak load demands - benefits for servicing utilities and park owners and tenants. The two handbooks developed by this project can help utilities identify existing or planned parks as potential cogeneration sites as well as help developers and park owners evaluate the advantages of cogeneration. The second handbook (volume 3) describes the benefits of cogeneration for park developers, owners, and tenants.

Schiller, S.R.; Minicucci, D.D.; Tamaro, R.F.

1986-05-01T23:59:59.000Z

202

A Case Study to Bottle the Biogas in Cylinders as Source of Power for Rural Industries Development in Pakistan  

E-Print Network (OSTI)

Abstract: Pakistan is one of the developing countries with very low energy consumption, correspondingly low standard of living and high population growth. The country is trying to improve its living standards by increasing its energy consumption and establishing appropriate industries. It has immense hydropower potential, which is almost untapped at the present time. Employment generation and poverty alleviation are the two main issues related with rural development. These issues can be tackled by rural industrialization using local resources and appropriate technologies. However, sufficient number of industries can not be set up in rural areas so far due to scarcity of energy supply i.e. electricity, diesel etc. Biogas, a renewable fuel may be able to fill the gap in energy availability in the rural areas. Biogas can supply energy near to biogas plant which makes it hindrance in its wide spread application and therefore mobility of biogas is must, which is achieved by bottling of biogas. Here a model is conceptualized to bottle the biogas in cylinders and then use it to power the rural industries. It is found that use of bottled biogas can save diesel of the worth US $ 147 in 12 hours and also generate employment for 12 persons. Key words: Employment rural industries biogas bottling

Syed Zafar Ilyas

2006-01-01T23:59:59.000Z

203

Developing system-based leading indicators for proactive risk management in the chemical processing industry  

E-Print Network (OSTI)

The chemical processing industry has faced challenges with achieving improvements in safety performance, and accidents continue to occur. When accidents occur, they usually have a confluence of multiple factors, suggesting ...

Khawaji, Ibrahim A. (Ibrahim Abdullah)

2012-01-01T23:59:59.000Z

204

Developing global inventory and resupply forecasting policies for the vaccines industry  

E-Print Network (OSTI)

Appropriate inventory management is important for many businesses throughout the world. For the vaccines industry, appropriate inventory policies impact both the business' profitability and people's lives. An optimal policy ...

Stark, Julia (Julia Anne)

2011-01-01T23:59:59.000Z

205

Development of New LLW Disposal Options: Phase I Interim Report on the EPRI Industry Strategic Database  

Science Conference Proceedings (OSTI)

Nuclear utilities need a comprehensive industry-wide LLW database to provide intelligence for executive level decision making related to the future of LLW disposal and clearance practices. NEI, the NRC and EPA are requesting this data. The US Government Accounting Office (GAO) also referenced a lack of reliable industry LLW data in its 2004 report on future US LLW disposal options. This report provides initial results from the EPRI initiative filling this data gap.

2005-12-06T23:59:59.000Z

206

The Economic Impact of the Natural Gas Industry and the Marcellus Shale Development in West Virginia in 2009  

E-Print Network (OSTI)

The Economic Impact of the Natural Gas Industry and the Marcellus Shale Development in West for this research was provided by the West Virginia Oil and Natural Gas Association (WVONGA). The opinions herein reservoir being the Marcellus Shale play. The Marcellus Shale play stretches across an area of 95,000 square

Mohaghegh, Shahab

207

The Development of an Innovative Vertical Floatation Melter and Scrap Dryer for Use in the Aluminum Processing Industry  

Science Conference Proceedings (OSTI)

The project aimed at the development of a Vertical Floatation melter, for application to the aluminum industry. This is intended to improve both the energy efficiency and environmental performance of aluminum melting furnaces. Phase I of this project dealt primarily with the initial research effort. Phase II, dealt with pilot-scale testing.

Robert De Saro

2004-08-24T23:59:59.000Z

208

Manufacturing Industrial Development for the Alternative Energy Systems-Final Report  

SciTech Connect

NCMS identified and developed critical manufacturing technology assessments vital to the affordable manufacturing of alternative-energy systems. NCMS leveraged technologies from other industrial sectors and worked with our extensive member organizations to provide DOE with two projects with far-reaching impact on the generation of wind energy. In the response for a call for project ideas, 26 project teams submitted ideas. Following a detailed selection criteria, two projects were chosen for development: Advanced Manufacturing for Modular Electro-kinetic (E-K) Wind Energy Conversion Technology - The goal of this project was to demonstrate that a modular wind energy technology based on electrohydrodynamic wind energy principles and employing automotive heritage high volume manufacturing techniques and modular platform design concepts can result in significant cost reductions for wind energy systems at a range of sizes from 100KW to multi-MW. During this program, the Accio/Boeing team made major progress on validating the EHD wind energy technology as commercially viable in the wind energy sector, and moved along the manufacturing readiness axis with a series of design changes that increased net system output. Hybrid Laser Arc Welding for Manufacture of Wind Towers - The goal of this research program was to reduce the cost of manufacturing wind towers through the introduction of hybrid laser arc welding (HLAW) into the supply chain for manufacturing wind towers. HLAW has the potential to enhance productivity while reducing energy consumption to offset the foreign low-cost labor advantage and thereby enhance U.S. competitiveness. HLAW technology combines laser welding and arc welding to produce an energy efficient, high productivity, welding process for heavy manufacturing. This process leverages the ability of a laser to produce deep weld penetration and the ability of gas metal arc welding (GMAW) to deposit filler material, thereby producing stable, high quality, welds on joints with gaps and mismatches typical of those seen in heavy manufacturing. Wind towers utilize varying thicknesses of steel throughout their structures to meet the mechanical load requirements while keeping material costs low. A typical tower might have as many as twelve different material thicknesses. Joining each thickness requires a unique joint design and welding approach to enable the management of quality, productivity, and mechanical properties. In this program, laser joining of materials with thicknesses ranging from 12mm to 35mm were evaluated against the standard quality and mechanical requirements for General Electric wind tower components. The joining processes demonstrated showed the ability to meet key requirements with the appropriate process controls in place.

Dr. Chuck Ryan, National Center for Manufacturing Sciences; Dr. Dawn White, Accio Energy; Mr. Duncan Pratt, General Electric Global Research

2013-01-30T23:59:59.000Z

209

A Critical Analysis of Technological Innovation and Economic Development in Southern California's Urban Water Reuse And Recycling Industry  

E-Print Network (OSTI)

of the Biotechnology Industry." Proceedings of the NationalAustralias Dynamic Water Industry: Fostering Excellence inEngineering Services Global Industry Report. Imagine H20,

Pilip-Florea, Shadrach Jay

2012-01-01T23:59:59.000Z

210

A Survey of the U.S. ESCO Industry: Market Growth and Development from 2008 to 2011  

SciTech Connect

In this study, LBNL analyzes the current size of the Energy Service Company (ESCO) industry, industry growth projections to 2011, and market trends in order to provide policymakers with a more indepth understanding of energy efficiency activity among private sector firms. We draw heavily on information from interviews with ESCOs conducted from October 2009 to February 2010 and from our review of publicly available financial information regarding individual ESCOs. A significant ramp-up in energy efficiency activities is occurring at the local, state, and federal level. These activities include the establishment in {approx}18 states of statewide energy savings goals to be obtained from adoption of an Energy Efficiency Resource Standard (EERS), legislative or state regulatory directives to obtain all cost-effective demand-side resources (Barbose et al 2009), and a significant increase in federal funding for energy efficiency programs as part of the American Recovery and Reinvestment Act (ARRA). As part of this increased focus on energy efficiency, policymakers are evaluating the role of private sector companies, including ESCOs, in delivering cost-effective energy savings to end-users. The U.S. ESCO industry has long been recognized for its role in successfully delivering comprehensive energy projects in the public sector. This study analyzes the current size of the ESCO industry, industry growth projections, and market trends in order to provide policymakers with a more in-depth understanding of energy efficiency activity among private sector firms. This study may also be of interest to policymakers abroad who are exploring options to encourage development of a private-sector energy services industry in their own countries. This study draws heavily on information from interviews with ESCOs conducted from October 2009 to February 2010 and is part of a series of ESCO industry reports prepared by Lawrence Berkeley National Laboratory (LBNL) in collaboration with the National Association of Energy Services Companies (NAESCO). The analysis builds on previous ESCO industry reports (see Goldman et al. 2005 and Hopper et al. 2007) and provides updated estimates of ESCO industry revenues and ESCO views on perceived trends in costs and savings.

Satchwell, Andrew; Goldman, Charles; Larsen, Peter; Gilligan, Donald; Singer, Terry

2010-06-08T23:59:59.000Z

211

Opportunities and Challenges for Development of a Mature Concentrating Photovoltaic Power Industry (Revision)  

DOE Green Energy (OSTI)

This report summarizes the current status of the CPV industry and is updated from previous versions to include information from the last year. New information presented at the CPV-8 conference is included along with the addition of new companies that have announced their interest in CPV, and estimates of production volumes for 2011 and 2012.

Kurtz, S.

2012-11-01T23:59:59.000Z

212

A Critical Analysis of Technological Innovation and Economic Development in Southern California's Urban Water Reuse And Recycling Industry  

E-Print Network (OSTI)

and commercial and industrial refrigeration and freezerrefrigeration equipment (except household-type refrigerators, freezers, and air-conditioners) Industrial

Pilip-Florea, Shadrach Jay

2012-01-01T23:59:59.000Z

213

The impact of government policies on industrial evolution : the case of China's automotive industry  

E-Print Network (OSTI)

Governmental industrial policies have great influence on industrial performances and development trajectories. The infant industry theory has been the dominating theoretical foundation of the industrial policies in developing ...

Luo, Jianxi

2006-01-01T23:59:59.000Z

214

Development and Testing of Industrial Scale Coal Fired Combustion System, Phase 3  

SciTech Connect

Coal Tech Corp's mission is to develop, license & sell innovative, lowest cost, solid fuel fired power systems & total emission control processes using proprietary and patented technology for domestic and international markets. The present project 'DEVELOPMENT & TESTING OF INDUSTRIAL SCALE, COAL FIRED COMBUSTION SYSTEM, PHASE 3' on DOE Contract DE-AC22-91PC91162 was a key element in achieving this objective. The project consisted of five tasks that were divided into three phases. The first phase, 'Optimization of First Generation 20 MMBtu/hr Air-Cooled Slagging Coal Tech Combustor', consisted of three tasks, which are detailed in Appendix 'A' of this report. They were implemented in 1992 and 1993 at the first generation, 20 MMBtu/hour, combustor-boiler test site in Williamsport, PA. It consisted of substantial combustor modifications and coal-fired tests designed to improve the combustor's wall cooling, slag and ash management, automating of its operation, and correcting severe deficiencies in the coal feeding to the combustor. The need for these changes was indicated during the prior 900-hour test effort on this combustor that was conducted as part of the DOE Clean Coal Program. A combination of combustor changes, auxiliary equipment changes, sophisticated multi-dimensional combustion analysis, computer controlled automation, and series of single and double day shift tests totaling about 300 hours, either resolved these operational issues or indicated that further corrective changes were needed in the combustor design. The key result from both analyses and tests was that the combustor must be substantially lengthened to maximize combustion efficiency and sharply increase slag retention in the combustor. A measure of the success of these modifications was realized in the third phase of this project, consisting of task 5 entitled: 'Site Demonstration with the Second Generation 20 MMBtu/hr Air-Cooled Slagging Coal Tech Combustor'. The details of the task 5 effort are contained in Appendix 'C'. It was implemented between 1994 and 1998 after the entire 20 MMBtu/hr combustor-boiler facility was relocated to Philadelphia, PA in 1994. A new test facility was designed and installed. A substantially longer combustor was fabricated. Although not in the project plan or cost plan, an entire steam turbine-electric power generating plant was designed and the appropriate new and used equipment for continuous operation was specified. Insufficient funds and the lack of a customer for any electric power that the test facility could have generated prevented the installation of the power generating equipment needed for continuous operation. All other task 5 project measures were met and exceeded. 107 days of testing in task 5, which exceeded the 63 days (about 500 hours) in the test plan, were implemented. Compared to the first generation 20 MMBtu/hr combustor in Williamsport, the 2nd generation combustor has a much higher combustion efficiency, the retention of slag inside the combustor doubled to about 75% of the coal ash, and the ash carryover into the boiler, a major problem in the Williamsport combustor was essentially eliminated. In addition, the project goals for coal-fired emissions were exceeded in task 5. SO{sub 2} was reduced by 80% to 0.2 lb/MMBtu in a combination of reagent injection in the combustion and post-combustion zones. NO{sub x} was reduced by 93% to 0.07 lb/MMBtu in a combination of staged combustion in the combustor and post-combustion reagent injection. A baghouse was installed that was rated to 0.03 lb/MMBtu stack particle emissions. The initial particle emission test by EPA Method 5 indicated substantially higher emissions far beyond that indicated by the clear emission plume. These emissions were attributed to steel particles released by wall corrosion in the baghouse, correction of which had no effect of emissions.

Bert Zauderer

1998-09-30T23:59:59.000Z

215

Optoelectronic implementations of Pulse-Coupled Neural Networks : challenges and limitations  

E-Print Network (OSTI)

This thesis examines Pulse Coupled Neural Networks (PCNNs) and their applications, and the feasibility of a compact, rugged, cost-efficient optoelectronic implementation. Simulation results are presented. Proposed optical ...

Wise, Raydiance (Raydiance Raychele)

2007-01-01T23:59:59.000Z

216

Organic optoelectronic devices based on platinum(ii) complexes and polymers  

Science Conference Proceedings (OSTI)

In this study, the syntheses and characterizations of platinum(II) complexes and polymers for applications in organic optoelectronic devices, such as light-emitting devices (LEDs) and photovoltaic (PV) cells, were explored in detail. The photoluminescent ...

Hai-Feng Xiang

2005-01-01T23:59:59.000Z

217

Japanese and American competition in the development of scroll compressors and its impact on the American air conditioning industry  

SciTech Connect

This report examines the technological development of scroll compressors and its impact on the air conditioning equipment industry. Scroll compressors, although considered to be the compressors of the future for energy-efficient residential heat pumps and possibly for many other applications, are difficult to manufacture on a volume-production base. The manufacturing process requires computer-aided, numerically controlled tools for high-precision fabrication of major parts. Japan implemented a global strategy for dominating the technological world market in the 1970s, and scroll compressor technology benefited from the advent of new-generation machine tools. As a result, if American manufacturers of scroll compressors purchase or are essentially forced to purchase numerically controlled tools from Japan in the future, they will then become dependent on their own competitors because the same Japanese conglomerates that make numerically controlled tools also make scroll compressors. This study illustrates the importance of the basic machine tool industry to the health of the US economy. Without a strong machine tool industry, it is difficult for American manufacturers to put innovations, whether patented or not, into production. As we experience transformation in the air conditioning and refrigeration market, it will be critical to establish a consistent national policy to provide healthy competition among producers, to promote innovation within the industry, to enhance assimilation of new technology, and to eliminate practices that are incompatible with these goals. 72 refs., 8 figs., 1 tab.

Ushimaru, Kenji (Energy International, Inc., Bellevue, WA (USA))

1990-02-01T23:59:59.000Z

218

Power Industry Development Paths and Natural Gas Market Risks: Cycles of Markets, Drilling, and Demand  

Science Conference Proceedings (OSTI)

The current natural gas market is depressed by a combination of unusual factorsa great excess of supply and weak demand. Excess supply comes from the momentum of exploration and production (EP) to the new U.S. gas shale plays, a phenomenon barely 18 months old and a game-changing event in the industry. Weak demand comes from the "Great Recession." The seeds for correcting this imbalance would appear to be a dramatic cutback in drilling, which has collapsed over the past year and which is a principal focu...

2009-09-28T23:59:59.000Z

219

Development of New Industrial Ashalloy Material Using Fly Ash Cenospheres "Lead-Lite" Project  

Science Conference Proceedings (OSTI)

One potential high-value utilization method for power plant fly ash is to mix it with an alloy to make a metal matrix composite. In the case of this project, the fly ash is mixed with lead to make a composite with low density and improved hardness. This new material can be used in the auto industry to make lighter battery components. This report describes the results of corrosion tests of several lead samples and lead-fly ash composite samples at room temperature for more than 1500 days. This long-term d...

1999-11-10T23:59:59.000Z

220

Methodological and Practical Considerations for Developing Multiproject Baselines for Electric Power and Cement Industry Projects in Central America  

E-Print Network (OSTI)

from the global cement industry, Ann. Rev. Energy Environ.were estimated. Cement industry BERs ranged from 205 kgCO 2carbon intensity, cement industry, Central America, electric

Murtishaw, Scott; Sathaye, Jayant; Galitsky, Christina; Dorion, Kristel

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Industry participation in DOE-sponsored geopressured geothermal research development. Final report, May 1, 1979-April 30, 1982  

DOE Green Energy (OSTI)

Nine DOE/Industry Forum meetings where the progress of DOE's resource development program was outlined and discussed were planned, organized, conducted, and reported. These nine forum meetings included three meetings of the Drilling and Testing group, two Site Selection meetings, one meeting each of the Legal and Environmental groups and two Overview meetings where the entire DOE program was discussed. Summaries of each of these meetings are included and the progress of DOE's geopressured geothermal resource evaluation program from its early beginnings to demonstration of the tremendous size and widespread availability of this supplementary energy resource are shown. Attendees at the meetings represented a broad cross section of state and federal agencies and potential users and developers of this large energy source. Attendance at meetings averages 50 to 80 with the most interest shown at meetings where reservoir testing results were discussed. In addition to the forums 16 newsletters were prepared and distributed to all participants. These were instituted to keep industry apprised of the latest developments in this DOE resource evaluation program. Three additional studies were carried out for DOE under this contract: a reservoir continuity study, a survey of gas stripping operations, and the development of a lease agreement for design well prospects.

Coffer, H.F.

1982-07-01T23:59:59.000Z

222

Standardizing model-based in-vehicle infotainment development in the German automotive industry  

Science Conference Proceedings (OSTI)

Based on the analysis of existing HMI development processes in the automotive domain, a reference process for software engineering has been developed. This process was used to develop a domain data model and a model-based specification language in order ... Keywords: HMI, automotive, domain data model, interaction design, model-based language, specification, user interface design

Steffen Hess; Anne Gross; Andreas Maier; Marius Orfgen; Gerrit Meixner

2012-10-01T23:59:59.000Z

223

DEVELOPMENT AND DEMONSTRATION OF NOVEL LOW-NOx BURNERS IN THE STEEL INDUSTRY  

DOE Green Energy (OSTI)

During field evaluation on a 174 million Btu/h industrial prototype burner both natural gas and actual COG from on-site generation were tested. Despite the elevated hydrogen cyanide and ammonia content in the COG throughout the test program, the FIR burner showed an improvement over baseline emissions. At full load; 167 million Btu/h, NOx emissions were relatively low at 169 vppm. This represents a 30% reduction compared to baseline emissions not accounting for the higher hydrogen cyanide content in the COG. CO emissions remained below 20 vppm and were stable across the firing range. This represents a 68% reduction compared to baseline CO emissions. When firing natural gas, emissions were stable as firing rate increased over the range. At low fire; 45 million Btu/h, NOx emissions where 33 vppm and increased at full load; 144 million Btu

Cygan, David

2006-12-28T23:59:59.000Z

224

CHINA'S SOFTWARE INDUSTRY CURRENT STATUS AND DEVELOPMENT STRATEIES Hongli Hu, Xi'an Jiaotong University, hhl@xjtu.edu.cn, Tel: +86-29-527-6916  

E-Print Network (OSTI)

CHINA'S SOFTWARE INDUSTRY ­ CURRENT STATUS AND DEVELOPMENT STRATEIES Hongli Hu, Xi'an Jiaotong: Although software industry in China is still at the primitive stage, with her huge personnel resource, the demands from her fast growing economy, and government's promotional policies, China will inevitably become

Lin, Zhangxi

225

Holistic revitalization in small post-industrial cities : tools for urban housing development  

E-Print Network (OSTI)

For generations, housing programs have sought to utilize redevelopment projects to accomplish broader community revitalization goals. Contemporary affordable housing practice embodies this idea in large housing development ...

Beam, Jeffrey (Jeffrey J.)

2009-01-01T23:59:59.000Z

226

Western Europe: North Sea developments take priority. [Oil and gas industry activity in Western Europe  

SciTech Connect

This paper reviews the 1992-1993 years exploration and development in the onshore and offshore areas of western Europe. The North Sea area is considered a priority for future development because of the United Kingdom's recent abolition of financial incentives and subsidies to continental exploration and development. The paper provides figures on numbers of new wells, total footages, financial expenditures on exploration and development, and production from oil and gas producing countries. Specifically, these include the United Kingdom, Norway, the Netherlands, Denmark, France, Germany, Italy, Austria, Greece, and Spain.

Hughes, C.; Andersen, A.

1993-08-01T23:59:59.000Z

227

Development of a New Class of Fe-3Cr-W(V) Ferritic Steels for Industrial Process Applications  

SciTech Connect

The project described in this report dealt with improving the materials performance and fabrication for hydrotreating reactor vessels, heat recovery systems, and other components for the petroleum and chemical industries. These reactor vessels can approach ship weights of about 300 tons with vessel wall thicknesses of 3 to 8 inches. They are typically fabricated from Fe-Cr-Mo alloy steels, containing 1.25 to 12% chromium and 1 to 2% molybdenum. The goal of this project was to develop Fe-Cr-W(V) steels that can perform similar duties, in terms of strength at high temperatures, but will weigh less and thereby save energy.

Jawad, Mann; Sikka, Vinod K.

2005-04-06T23:59:59.000Z

228

High performance steam development. Final report, Phase No. 3: 1500{degree}F steam plant for industrial cogeneration prototype development tests  

Science Conference Proceedings (OSTI)

As a key part of DOE`s and industry`s R&D efforts to improve the efficiency, cost, and emissions of power generation, a prototype High Performance Steam System (HPSS) has been designed, built, and demonstrated. The world`s highest temperature ASME Section I coded power plant successfully completed over 100 hours of development tests at 1500{degrees}F and 1500 psig on a 56,000 pound per hour steam generator, control valve and topping turbine at an output power of 5500 hp. This development advances the HPSS to 400{degrees}F higher steam temperature than the current best technology being installed around the world. Higher cycle temperatures produce higher conversion efficiencies and since steam is used to produce the large majority of the world`s power, the authors expect HPSS developments will have a major impact on electric power production and cogeneration in the twenty-first century. Coal fueled steam plants now produce the majority of the United States electric power. Cogeneration and reduced costs and availability of natural gas have now made gas turbines using Heat Recovery Steam Generators (HRSG`s) and combined cycles for cogeneration and power generation the lowest cost producer of electric power in the United States. These gas fueled combined cycles also have major benefits in reducing emissions while reducing the cost of electricity. Development of HPSS technology can significantly improve the efficiency of cogeneration, steam plants, and combined cycles. Figure 2 is a TS diagram that shows the HPSS has twice the energy available from each pound of steam when expanding from 1500{degrees}F and 1500 psia to 165 psia (150 psig, a common cogeneration process steam pressure). This report describes the prototype component and system design, and results of the 100-hour laboratory tests. The next phase of the program consists of building up the steam turbine into a generator set, and installing the power plant at an industrial site for extended operation.

Duffy, T.; Schneider, P.

1996-01-01T23:59:59.000Z

229

Development and Field Trial of Dimpled-Tube Technology for Chemical Industry Process Heaters  

SciTech Connect

Most approaches to increasing heat transfer rates in the convection sections of gas-fired process heaters involve the incorporation of fins, baffles, turbulizers, etc. to increase either the heat transfer surface area or turbulence or both. Although these approaches are effective in increasing the heat transfer rates, this increase is invariably accompanied by an associated increase in convection section pressure drop as well as, for heaters firing dirty fuel mixtures, increased fouling of the tubes both of which are highly undesirable. GTI has identified an approach that will increase heat transfer rates without a significant increase in pressure drop or fouling rate. Compared to other types of heat transfer enhancement approaches, the proposed dimpled tube approach achieves very high heat transfer rates at the lowest pressure drops. Incorporating this approach into convection sections of chemical industry fired process heaters may increase energy efficiency by 3-5%. The energy efficiency increase will allow reducing firing rates to provide the required heating duty while reducing the emissions of CO2 and NOx.

Yaroslav Chudnovsky; Aleksandr Kozlov

2006-10-12T23:59:59.000Z

230

Poultry Industry: Industry Brief  

Science Conference Proceedings (OSTI)

This Electric Power Research Institute (EPRI) Industry Brief provides an overview of the U.S. poultry industry and ways in which electric-powered processes and technologies can be used in poultry and egg production and processing. The poultry industry, which consists of poultry production for meat as well as egg production and processing, is one of the fastest growing segments of the U.S. food manufacturing industry. It is also an energy-intensive industry. In fact, a 2010 report by the USDA illustrates ...

2011-03-30T23:59:59.000Z

231

Methodological and Practical Considerations for DevelopingMultiproject Baselines for Electric Power and Cement Industry Projects inCentral America  

Science Conference Proceedings (OSTI)

The Lawrence Berkeley National Laboratory (Berkeley Lab) andthe Center for Sustainable Development in the Americas (CSDA) conductedtechnical studies and organized two training workshops to developcapacity in Central America for the evaluation of climate changeprojects. This paper describes the results of two baseline case studiesconducted for these workshops, one for the power sector and one for thecement industry, that were devised to illustrate certain approaches tobaseline setting. Multiproject baseline emission rates (BERs) for themain Guatemalan electricity grid were calculated from 2001 data. Inrecent years, the Guatemalan power sector has experienced rapid growth;thus, a sufficient number of new plants have been built to estimateviable BERs. We found that BERs for baseload plants offsetting additionalbaseload capacity ranged from 0.702 kgCO2/kWh (using a weighted averagestringency) to 0.507 kgCO2/kWh (using a 10th percentile stringency),while the baseline for plants offsetting load-followingcapacity is lowerat 0.567 kgCO2/kWh. For power displaced from existing load-followingplants, the rate is higher, 0.735 kgCO2/kWh, as a result of the age ofsome plants used for meeting peak loads and the infrequency of their use.The approved consolidated methodology for the Clean Development Mechanismyields a single rate of 0.753 kgCO2/kWh. Due to the relatively smallnumber of cement plants in the region and the regional nature of thecement market, all of Central America was chosen as the geographicboundary for setting cement industry BERs. Unfortunately, actualoperations and output data were unobtainable for most of the plants inthe region, and many data were estimated. Cement industry BERs rangedfrom 205 kgCO2 to 225 kgCO2 per metric ton of cement.

Murtishaw, Scott; Sathaye, Jayant; Galitsky, Christina; Dorion,Kristel

2004-09-02T23:59:59.000Z

232

The Paradox of Regulatory Development in China: The Case of the Electricity Industry  

E-Print Network (OSTI)

the rising barriers to electricity trade across provinces. AEconomic and Trade Commission State Electricity Regulatoryand trade commissions (PETCs) and provincial development and planning commissions (PDPCs) took on the responsibilities of managing the electricity

Tsai, Chung-min

2010-01-01T23:59:59.000Z

233

Developing the business case for Quality by Design in the biopharmaceutical industry  

E-Print Network (OSTI)

Quality by Design (QbD) is a systematic, science-based approach to pharmaceutical development that was defined in the International Conference on Harmonization (ICH) Q8 guideline in 2005. Expectations are that QbD will ...

Matthew, Julie (Julie Elizabeth)

2009-01-01T23:59:59.000Z

234

Global niche markets and local development : clientelism and fairtrade farmer organizations in Paraguay's sugar industry  

E-Print Network (OSTI)

Globalization has transformed the markets in which agricultural goods are traded, placing new demands on farmers around the world. In developing countries, smallholder and peasant farmers lack many of the resources needed ...

Setrini, Gustavo

2011-01-01T23:59:59.000Z

235

1 New Technologies, Industry Developments and Emission Trends in Key Sectors: The Energy Sector  

E-Print Network (OSTI)

Australias total primary energy consumption grew by 3.6 per cent per annum between 1993/94 and 1997/98, while primary energy use in the electricity sector rose by more than 5 per cent per year over the same period. Since 1993/94, brown coal has strongly expanded its share in the fuel mix of the interconnected electricity markets of Victoria, New South Wales, the Australian Capital Territory, and South Australia. It has become the primary fuel source for electricity generation, substituting for hydro, natural gas and hard coal. At the national level, this has meant that the long-term trend towards greater use of natural gas has stalled in favour of coal, especially brown coal. Since Victorias brown coal plants have relatively low thermal efficiencies, this substitution has also had the effect of reducing the average thermal efficiency in the power market to the levels of the late 1980s (IEA, 2001b). It should be noted that the economic objective of reducing the price of power which has driven the first stage of reform in the electricity industry in Australia has perversely encouraged the aggregate use of energy in the economy. This, in turn, has added to the growth of greenhouse gas emissions, reinforcing the trend associated with the change in the fuel mix for electricity generation. This paper addresses non-transport energy-related activities including conventional and renewable forms of energy supply, cross-cutting technologies employed in the energy sector and, more briefly, energy use by the business and household sectors.

Ainsley Jolley

2004-01-01T23:59:59.000Z

236

A program to develop the domestic natural gas industry in Indonesia: Case history of two World Bank projects  

Science Conference Proceedings (OSTI)

Indonesia depends heavily on revenues from the export of LNG and oil, the availability of which appears to be decreasing. It is therefore making a strong effort to accelerate development of a domestic natural gas industry. A high priority has been given to the conversion of power plants and city gas systems, including local industries and commercial facilities, from liquid fuels to natural gas. This will release more oil for export, help to meet the objectives of Repelita V, and provide substantial environmental benefits. The World Bank recently provided loans to the Indonesian Government for two projects that are aimed at substituting natural gas for oil and manufactured gas in domestic markets. One project involves expansion of the gas distribution systems of Indonesia's natural gas utility (PGN) in three cities: Jakarta and Bogor in Java, and Medan in Sumatra. The project also includes training programs for PGN staff and an energy pricing policy study to be carried out by Indonesia's Ministry of Mines and Energy. The second project involves expansion of the supply of natural gas for Surabaya and twelve other towns in its vicinity in East Java, and further expansion of Medan's supply system. Technical assistance will be provided to enhance the skills ofPGN and the Ministry of Mines and Energy, and a Gas Technology Unit similar to the Institute of Gas Technology will be established at Indonesia's Research and Development Center for Oil and Gas (LEMIGAS) in Jakarta. 14 refs., 3 figs., 11 tabs.

Klass, D.L. (Institute of Gas Technology, Chicago, IL (United States)); Khwaja, S. (World Bank, Washington, DC (United States))

1991-01-01T23:59:59.000Z

237

Direct optoelectronic generation and detection of sub-ps-electrical pulses on sub-mm-coaxial transmission lines  

E-Print Network (OSTI)

-mm-coaxial transmission lines Tae-In Jeona) and D. Grischkowskyb) School of Electrical and Computer Engineering, OklahomaDirect optoelectronic generation and detection of sub-ps-electrical pulses on sub efficient direct optoelectronic generation of sub-ps-THz pulses on 50 coaxial transmission lines with a 330

Oklahoma State University

238

Femtosecond-laser irradiation as a platform for tailoring the optoelectronic properties of silicon  

E-Print Network (OSTI)

Silicon is the most abundant semiconductor on earth and benefits from decades of technological development driven by the integrated circuit industry. Furthermore, silicon allows for facile n-type and p-type doping, has a ...

Smith, Matthew John, Ph. D. Massachusetts Institute of Technology

2012-01-01T23:59:59.000Z

239

Recent developments in wear- and corrosion-resistant alloys for the oil industry  

SciTech Connect

Oil production and refining pose very severe wear and corrosion environments. Material designers are challenged with the need to design and develop materials that combine high corrosion resistance with good wear resistance. Coupled with that is the need for these materials to meet requirements such as fracture toughness and resistance to sulfide and chloride stress corrosion cracking. Often, increasing wear resistance compromises the corrosion and welding characteristics. This article covers a variety of material developments that address the problems of wear and corrosion, including alloy design fundamentals and pertinent wear properties and general corrosion resistance compared to traditional wear-resistant materials. Proven applications, with particular reference to petroleum and petrochemical areas, are discussed. Potential applications are also cited.

Raghu, D. [Deloro Stellite Inc., Goshen, IN (United States). Stellite Coatings Div.; Wu, J.B.C. [Stoody Deloro Stellite, Inc., St. Louis, MO (United States)

1997-11-01T23:59:59.000Z

240

Development of forest industries. (Latest citations from the NTIS bibliographic database). Published Search  

Science Conference Proceedings (OSTI)

The bibliography contains citations concerning the development of forestry for wood pulp and products. The production of structural timber, wooden logs, plywood, and wood fibers is discussed. Also discussed are forest management, forest growth and mortality, inventory management, and harvest residues for energy production. Employment opportunities, marketing, international trade, and air pollution are considered.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

NONE

1997-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Development of forest industries. (Latest citations from the NTIS bibliographic database). Published Search  

SciTech Connect

The bibliography contains citations concerning the development of forestry for wood pulp and products. The production of structural timber, wooden logs, plywood, and wood fibers is discussed. Also discussed are forest management, forest growth and mortality, inventory management, and harvest residues for energy production. Employment opportunities, marketing, international trade, and air pollution are considered.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

NONE

1996-02-01T23:59:59.000Z

242

Development of forest industries. (Latest citations from the NTIS bibliographic database). NewSearch  

Science Conference Proceedings (OSTI)

The bibliography contains citations concerning the development of forestry for wood pulp and products. The production of structural timber, wooden logs, plywood, and wood fibers is discussed. Also discussed are forest management, forest growth and mortality, inventory management, and harvest residues for energy production. Employment opportunities, marketing, international trade, and air pollution are considered. (Contains 250 citations and includes a subject term index and title list.)

Not Available

1994-10-01T23:59:59.000Z

243

Review: Wireless sensors in agriculture and food industry-Recent development and future perspective  

Science Conference Proceedings (OSTI)

This paper presents an overview on recent development of wireless sensor technologies and standards for wireless communications as applied to wireless sensors. Examples of wireless sensors and sensor networks applied in agriculture and food production ... Keywords: Bluetooth, CAN, CDMA, GPRS, GSM, HVAC, IEEE, IT, IrDA, LAN, M2M, MEMS, NCAP, NIST, PDA, RAS, RFID, SPWAS, STIM, TEDS, TII, USDA, WINA, WLAN, WPAN, WPS, WPSRD, WiFi, ZigBee

Ning Wang; Naiqian Zhang; Maohua Wang

2006-01-01T23:59:59.000Z

244

Current state, problems, and prospects of development of the fuel and power industry of the Russian Federation  

SciTech Connect

Despite the political and territorial changes that have occurred in the former USSR, the Russian Federation as before remains the core of the entire energy supply system of countries of the Commonwealth of Independent States (CIS), the three Baltic States, as well as an exporter of oil and gas to European countries. Demonstrated gas reserves in Russia amount to 47 trillion cubic meters and coal reserves more than 200 billion tons. With the dissolution of the USSR, the infrastructure of the entire region was affected. The main production of pipes remained in Ukraine and 80% of the production of oil equipment remained in Azerbaijan. The majority of underground gas storage facilities, refineries, and electric-power installations constructed during the past 20 years remained in Belarus, Baltic Countries, and Ukraine. To solve some of the problems, laws were passed that aimed at the formation of market relations in the economy and power industry. The transition to a market economy in the oil and gas industry should take 5-7 years and has a large effect on the overall markets reforms taking place. The article also outlines the history and present state of petroleum reserves and development in Russia.

Shatalov, A.T.

1994-09-01T23:59:59.000Z

245

Analysis of the apiclutural industry in relation to geothermal development and agriculture in the Imperial Valley, Imperial County, California  

DOE Green Energy (OSTI)

PART I: Continuous exposure to 30 ppB H/sub 2/S increased lifespan of caged worker honey bees, Apis mellifera L., 33%; whereas, bees exposed > 13 days to 100 ppB and 300 ppB H/sub 2/S the lifespan was shortened 32% and 51%, respectively, over unexposed bees; bees exposed > 15 days to a combination of 300 ppB H/sub 2/S + 50 ppM CO/sub 2/ the lifespan was shortened 4.4% more that 300 ppB H/sub 2/S alone. The mean temperature and/or relative humidity did not exert a direct effect on the hazard to bees. A continuous exposure to 300 ppB SO/sub 2/ was detrimental to caged worker honey bees; and, a mean temperature of 27.2/sup 0/C was 75.7% more toxic than the same dosage at 16.7/sup 0/C. Worker bee lifespans exposed to 300 ppB SO/sub 2/ at 16.7/sup 0/C were shortened 13.5% and 79%, respectively, compared to unexposed bees. Therefore, both dosage and temperature exert direct effects on the hazards to bees. PART II: The status of the apicultural industry in Imperial County, California, was outlined giving a short characterization of the area in relation to the apicultural industry. Agriculture utilizes 500,000 intensely farmed acres which generated a 11-year average income of $370 million. Over 40 agricultural commodities are produced. The apicultural industry is intimately involved in 25% of the total gross agricultural income. In addition, most of the flora growing in the desert community which comprises the remainder of the county are very important to honey bees by providing sustaining nectar and/or pollen for brood rearing. The bee foraged flora provides substantial bee forage when colonies are located outside of the agriculutral area. It is concluded that geothermal resource development in the Imperial Valley is contemplated to have minimal effects on the apicultural industry.

Atkins, E.L.

1979-04-01T23:59:59.000Z

246

The Challenge of Manufacturing Innovation: Industry, Rurality, and Competitiveness in the State of Georgia 1 Jan Youtie, Economic Development Institute  

E-Print Network (OSTI)

In a globalized market environment, the competitiveness of manufacturing which we understand as the ability to make and sell products while maintaining or increasing real income is influenced by many factors, including the growth of productivity and the exchange rate. In this paper, we focus on the role and extent of innovation as a basis for maintaining manufacturing competitiveness. Innovation encompasses steps and activities involved in the introduction and deployment of new or improved ideas within and between companies. Innovation includes product design and development, the development of new processes, organizational innovation, innovative customer service approaches, and the development of innovative linkages with other firms. In understanding innovation, it is important to consider how firms identify, acquire, develop and implement innovations, as well as the context, resources, values, knowledge base, and leadership that contribute to innovation. Successful innovation not only affects the firm engaging in it, but frequently has important spillovers, leading to additional benefits for users, suppliers, and regional industrial clusters as well as to the innovating firm. Our analysis draws on preliminary results of the Georgia Manufacturing Survey 2005. We find that innovative strategies are associated with higher returns to the firm and the community compared with strategies based on low price. The paper will also demonstrate that rural and urban manufacturers have comparable adoption rates of technology, but rural manufacturers have less use of soft enablers of innovation. The paper will conclude with a review of various policies and programs of the state of Georgia to encourage innovation among its manufacturing establishments.

Philip Shapira; School Of Public Policy

2005-01-01T23:59:59.000Z

247

Study of domestic social and economic impacts of ocean thermal energy conversion (OTEC) commercial development. Volume II. Industry profiles  

DOE Green Energy (OSTI)

Econoimc profiles of the industries most affected by the construction, deployment, and operation of Ocean Thermal Energy Conversion (OTEC) powerplants are presented. Six industries which will contribute materials and/or components to the construction of OTEC plants have been identified and are profiled here. These industries are: steel industry, concrete industry, titanium metal industry, fabricated structural metals industry, fiber glass-reinforced plastics industry, and electrical transmission cable industry. The economic profiles for these industries detail the industry's history, its financial and economic characteristics, its technological and production traits, resource constraints that might impede its operation, and its relation to OTEC. Some of the historical data collected and described in the profile include output, value of shipments, number of firms, prices, employment, imports and exports, and supply-demand forecasts. For most of the profiled industries, data from 1958 through 1980 were examined. In addition, profiles are included on the sectors of the economy which will actualy construct, deploy, and supply the OTEC platforms.

None

1981-12-22T23:59:59.000Z

248

Geothermal industry position paper: EPA regulatory options and research and development information needs  

DOE Green Energy (OSTI)

The environmental impact of geothermal energy development may be less intense or widespread than that of some other energy sources; however, it is the first example of a number of emerging energy technologies that must be dealt with by EPA. EPA may consider a spectrum of options ranging from a posutre of business as usual to one of immediate setting of standards, as favored by ERDA. The paper discusses the regulatory approaches and the potential problems that geothermal energy may present in the areas of air quality, water quality, and other impacts. It is recommended that a coordinated program of research be drawn up, comprised of specific research projects, the types of geothermal resource to which they apply, and the date by which the information is required.

D'Alessio, G.

1977-08-01T23:59:59.000Z

249

Geothermal Industry Position Paper: EPA Regulatory Options and Research and Development Information Needs  

DOE Green Energy (OSTI)

The environmental impact of geothermal energy development may be less intense or widespread than that of some other energy sources; however, it is the first example of a number of emerging energy technologies that must be dealt with by EPA. EPA may consider a spectrum of options ranging from a posture of business as usual to one of immediate setting of standards, as favored by ERDA. The paper discusses the regulatory approaches and the potential problems that geothermal energy may present in the areas of air quality, water quality, and other impacts. It is recommended that a coordinated program of research be drawn up, comprised of specific research projects, the types of geothermal resource to which they apply, and the date by which the information is required.

Swetnam, G.F.

1976-11-01T23:59:59.000Z

250

Technologies development for environmental restoration and waste management: International university and research institution and industry partnerships  

SciTech Connect

The Institute for Central and Eastern European Cooperative Environmental Research (ICEECER) at Florida State University was formed in 1990 soon after the end of the Cold War. ICEECER consists of a number of joint centers which link FSU, and US as well as international funding agencies, to academic and research institutions in Hungary, Poland, the Czech Republic, Russia, and the other countries of Central and Eastern Europe and the Newly Independent States. Areas of interest include risk assessment, toxicology, contaminated site remediation/characterization, waste management, emergency response, environmental technology development/demonstration/transfer, and some specialized areas of research (e.g., advanced chemical separations). Through ICEECER, numerous international conferences, symposia, training courses, and workshops have also been conducted on a variety of environmental topics. This paper summarizes the mission, structure, and administration of ICEECER and provides information on the projects conducted through this program at FSU.

Herndon, R.C.; Moerlins, J.E.; Kuperberg, J.M.

1996-12-31T23:59:59.000Z

251

Advanced coal-fueled industrial cogeneration gas turbine system particle removal system development  

SciTech Connect

Solar Turbines developed a direct coal-fueled turbine system (DCFT) and tested each component in subscale facilities and the combustion system was tested at full-scale. The combustion system was comprised of a two-stage slagging combustor with an impact separator between the two combustors. Greater than 90 percent of the native ash in the coal was removed as liquid slag with this system. In the first combustor, coal water slurry mixture (CWM) was injected into a combustion chamber which was operated loan to suppress NO{sub x} formation. The slurry was introduced through four fuel injectors that created a toroidal vortex because of the combustor geometry and angle of orientation of the injectors. The liquid slag that was formed was directed downward toward an impaction plate made of a refractory material. Sixty to seventy percent of the coal-borne ash was collected in this fashion. An impact separator was used to remove additional slag that had escaped the primary combustor. The combined particulate collection efficiency from both combustors was above 95 percent. Unfortunately, a great deal of the original sulfur from the coal still remained in the gas stream and needed to be separated. To accomplish this, dolomite or hydrated lime were injected in the secondary combustor to react with the sulfur dioxide and form calcium sulfite and sulfates. This solution for the sulfur problem increased the dust concentrations to as much as 6000 ppmw. A downstream particulate control system was required, and one that could operate at 150 psia, 1850-1900{degrees}F and with low pressure drop. Solar designed and tested a particulate rejection system to remove essentially all particulate from the high temperature, high pressure gas stream. A thorough research and development program was aimed at identifying candidate technologies and testing them with Solar`s coal-fired system. This topical report summarizes these activities over a period beginning in 1987 and ending in 1992.

Stephenson, M.

1994-03-01T23:59:59.000Z

252

Bank Reform in Greece with reference to Eastern Europe The Case of The Hellenic Industrial Development Bank S.A.  

E-Print Network (OSTI)

Is Greece a reforming economy? The purpose of this paper is to present the evolution and structure of the banking sector in Greece, with reference to the parallel experiences of the Eastern European (EE) countries. In Section 2, we are concerned with the domestic economic environment within which the Greek Banking System (GBS) operates. and the pressures building up within the system encouraging reform. In Section 3, we look into the evolution of the Greek Banking System, both in terms of structures and in terms of policy. Changes in the instruments of monetary policy are also considered in this section. In Section 4, we present the case of the Hellenic Industrial Development Bank, currently undergoing a thorough restructuring plan. In Section 5, we examine some of the main similarities and differences between Greece and the EE countries in relation to banking sector problems and reforms.

Marica Frangakis

1998-01-01T23:59:59.000Z

253

Structural Composites Industries 4-kilowatt wind-system development. Phase I. Design and analysis executive summary  

DOE Green Energy (OSTI)

A 4 kW small wind energy conversion system (SWECS) has been designed for residential applications in which relatively low (10 mph) mean annual wind speeds prevail. The objectives were to develop such a machinee to produce electrical energy at 6 cents per kWh while operating in parallel with a utility grid or auxiliary generator. Extensive trade, optimization and analytical studies were performed in an effort to provide the optimum machine to best meet the objectives. Certain components, systems and manufacturing processes were tested and evaluated and detail design drawings were produced. The resulting design is a 31-foot diameter horizontal axis downwind machine rated 5.7 kW and incorporating composite blades; free-standing composite tower; and torque-actuated blade pitch control. The design meets or exceeds all contract requirements except that for cost of energy. The target 6 cents per kWh will be achieved in a mean wind speed slightly below 12 mph instead of the specified 10 mph.

Malkine, N.; Bottrell, G.; Weingart, O.

1981-05-01T23:59:59.000Z

254

Dixie Valley, Nevada: A promising geothermal area under development by industry  

Science Conference Proceedings (OSTI)

Selected subsurface reservoirs located in the Western United States may contain significant geothermal energy, and if development continues, this energy source may provide substantial electrical power or related energy by the year 2,000. Utility management must be convinced of the reliability and cost attractiveness of this energy source. A number of exploration programs are in progress to evaluate the potential of geothermal energy in the United States. For example, numerous exploration methods have been employed in Dixie Valley, Nevada, since 1967 with mixed results. However, with DOE support, additional data have recently become available. The authors have revised earlier structural models of the basin and have made recommendations for additional investigations that should assist in clarifying the geologic relationships within the reservoir. The principal geologic characteristics of the reservoir that may place limits on project economics appear to be the depth and trend area of producing zones, fluid quality and the amenability of the upper zones to accept large volumes of spent fluids. However, reservoir temperature, flow rates, recharge characteristics, and other factors appear to be acceptable either for electrical power production of more than 1,000 MWe, or for direct applications such as on-site agricultural processing.

Campbell, M.D.

1983-08-01T23:59:59.000Z

255

Structural Composites Industries 4 kilowatt wind system development. Phase I: design and analysis, technical report  

DOE Green Energy (OSTI)

A 4 kW small wind energy conversion system (SWECS) has been designed for residential applications in which relatively low (10 mph) mean annual wind speeds prevail. The objectives were to develop such a machine to produce electrical energy at 6 cents per kWh while operating in parallel with a utility grid or auxiliary generator. The Phase I effort began in November, 1979 and was carried through the Final Design Review in February 1981. During this period extensive trade, optimization and analytical studies were performed in an effort to provide the optimum machine to best meet the objectives. Certain components, systems and manufacturing processes were tested and evaluated and detail design drawings were produced. The resulting design is a 31-foot diameter horizontal axis downwind machine rated 5.7 kW and incorporating the following unique features: Composite Blades; Free-Standing Composite Tower; Torque-Actuated Blade Pitch Control. The design meets or exceeds all contract requirements except that for cost of energy. The target 6 cents per kWh will be achieved in a mean wind speed slightly below 12 mph instead of the specified 10 mph.

Malkine, N.; Bottrell, G.; Weingart, O.

1981-05-01T23:59:59.000Z

256

3D Optoelectronic Fix Point Unit and Its Advantages Processing 3D Data  

Science Conference Proceedings (OSTI)

In this paper we show the design of a 3 dimensional optoelectronic hardware approach to realize a fix point processing unit. For that we show the main ideas of the low level algorithm. We will introduce several concepts and evaluate them with regard ...

B. Kasche; Dietmar Fey; T. Hhn; Werner Erhard

1999-08-01T23:59:59.000Z

257

Dairy Industry: Industry Brief  

Science Conference Proceedings (OSTI)

This Electric Power Research Institute (EPRI) Industry Brief provides an overview of the U.S. dairy industry and ways in which electric-powered processes and technologies can be used in milk production and processing. Because of the different processes involved, the characteristics of energy consumption at milk production and processing facilities vary by facility. Most energy used in milk production is in the form of diesel fuel, followed by electricity and then by petroleum products such as gasoline an...

2011-03-30T23:59:59.000Z

258

Development of a computer-aided fault tree synthesis methodology for quantitative risk analysis in the chemical process industry  

E-Print Network (OSTI)

There has been growing public concern regarding the threat to people and environment from industrial activities, thus more rigorous regulations. The investigation of almost all the major accidents shows that we could have avoided those tragedies with effective risk analysis and safety management programs. High-quality risk analysis is absolutely necessary for sustainable development. As a powerful and systematic tool, fault tree analysis (FTA) has been adapted to the particular need of chemical process quantitative risk analysis (CPQRA) and found great applications. However, the application of FTA in the chemical process industry (CPI) is limited. One major barrier is the manual synthesis of fault trees. It requires a thorough understanding of the process and is vulnerable to individual subjectivity. The quality of FTA can be highly subjective and variable. The availability of a computer-based FTA methodology will greatly benefit the CPI. The primary objective of this research is to develop a computer-aided fault tree synthesis methodology for CPQRA. The central idea is to capture the cause-and-effect logic around each item of equipment directly into mini fault trees. Special fault tree models have been developed to manage special features. Fault trees created by this method are expected to be concise. A prototype computer program is provided to illustrate the methodology. Ideally, FTA can be standardized through a computer package that reads information contained in process block diagrams and provides automatic aids to assist engineers in generating and analyzing fault trees. Another important issue with regard to QRA is the large uncertainty associated with available failure rate data. In the CPI, the ranges of failure rates observed could be quite wide. Traditional reliability studies using point values of failure rates may result in misleading conclusions. This dissertation discusses the uncertainty with failure rate data and proposes a procedure to deal with data uncertainty in determining safety integrity level (SIL) for a safety instrumented system (SIS). Efforts must be carried out to obtain more accurate values of those data that might actually impact the estimation of SIL. This procedure guides process hazard analysts toward a more accurate SIL estimation and avoids misleading results due to data uncertainty.

Wang, Yanjun

2004-12-01T23:59:59.000Z

259

Prospects for the medium- and long-term development of China`s electric power industry and analysis of the potential market for superconductivity technology  

Science Conference Proceedings (OSTI)

First of all, overall economic growth objectives in China are concisely and succinctly specified in this report. Secondly, this report presents a forecast of energy supply and demand for China`s economic growth for 2000--2050. In comparison with the capability of energy construction in China in the future, a gap between supply and demand is one of the important factors hindering the sustainable development of Chain`s economy. The electric power industry is one of China`s most important industries. To adopt energy efficiency through high technology and utilizing energy adequately is an important technological policy for the development of China`s electric power industry in the future. After briefly describing the achievements of China`s electric power industry, this report defines the target areas and policies for the development of hydroelectricity and nuclear electricity in the 2000s in China, presents the strategic position of China`s electric power industry as well as objectives and relevant plans of development for 2000--2050. This report finds that with the discovery of superconducting electricity, the discovery of new high-temperature superconducting (HTS) materials, and progress in materials techniques, the 21st century will be an era of superconductivity. Applications of superconductivity in the energy field, such as superconducting storage, superconducting transmission, superconducting transformers, superconducting motors, its application in Magneto-Hydro-Dynamics (MHD), as well as in nuclear fusion, has unique advantages. Its market prospects are quite promising. 12 figs.

Li, Z. [Bob Lawrence and Associates, Inc., Alexandria, VA (United States)

1998-05-01T23:59:59.000Z

260

Development of an expert system for tackling the public's perception to climate-change impacts on petroleum industry  

Science Conference Proceedings (OSTI)

Climate change could cause significant impacts on human activities, which is especially true for regions that are of high latitude such as Canada. Petroleum industry is a main economic sector in Canada's prairie, where a number of its production and ... Keywords: Adaptation, Climate change, Expert system, Knowledge acquisition, Petroleum industry

Y. F. Huang; G. H. Huang; Z. Y. Hu; I. Maqsood; A. Chakma

2005-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Development of a partnership with government and industry to accelerate the commercialization of hydrogen. Final report, 9/30/1995--10/31/1996  

SciTech Connect

This Final Technical Report provides a summary of the activities performed by the NHA in accordance with the Cooperative Agreement. Activities are broken down by task area, and include the following: (1) Information exchange within the NHA, which includes the two NHA newsletters, the NHA Advocate, and the H{sub 2} Digest, as well as directory information. (2) Information exchange within the hydrogen industry, which includes conferences and meeting attendance, presentations of papers, and HTAP activities. (3) Information exchange with other critical industries and the public, which includes press conferences, and public awareness activities. (4) Annual US hydrogen meeting, NHA`s signature event. The 7th Annual US Hydrogen Meeting was held April 2--4, 1996 in Alexandria, Virginia in conjunction with the US DOE`s Hydrogen Technical Advisory Panel Meeting and the SAE`s Fuel Cell TOPTEC. (5) Industry perspective and needs, which covers activities related to the Hydrogen Industrialization Plan. (6) Codes and standards, which includes workshop and workgroup activities, as well as other safety-related activities. The objective of the codes and standards activities is to establish expert working groups to develop industry consensus on safety issues, and develop compatible standards and formats, and product certification protocols.

1996-12-31T23:59:59.000Z

262

Industrialization under the WTO : the impact of asymmetric free trade agreements on middle-technology developing countries  

E-Print Network (OSTI)

This dissertation addresses the issue of industrialization in the WTO regime, focusing on the role of asymmetric free trade agreements. It proposes a framework where free trade agreements offer payoffs that countries have ...

DiCaprio, Alisa

2007-01-01T23:59:59.000Z

263

A Survey of the U.S. ESCO Industry: Market Growth and Development from 2008 to 2011  

E-Print Network (OSTI)

Evolution of the U.S. Energy Service Company Industry: NewAn international survey of the energy service company (ESCO)Association of Energy Service Companies Environmental Energy

Satchwell, Andrew

2010-01-01T23:59:59.000Z

264

Politics, jobs and workforce development : the role of workforce intermediaries in building career pathways within Boston's health care industry  

E-Print Network (OSTI)

This research study examines the role that workforce intermediaries within Boston play in creating career pathways for economically disadvantaged, under-skilled residents in the local health care industry. Using a case ...

Hutson, Malo

2006-01-01T23:59:59.000Z

265

ooSEM (poster session): a process model for object-oriented development in an industrial environment  

Science Conference Proceedings (OSTI)

Applying current object-oriented (OO) methods in an industrial environment is by itself not sufficient for a certification according to the norm EN ISO 9001, which requires the application of a comprehensive process model that includes, among other things, ...

Hermann Kaindl; Stefan Huber; mer Karacan; Ilir Kondo; Herwig Schreiner; Helge-Wernhard S

2000-01-01T23:59:59.000Z

266

Innovation and the state : development strategies for high technology industries in a world of fragmented production : Israel, Ireland, and Taiwan  

E-Print Network (OSTI)

One of the most unexpected changes of the 1990s is that firms in a number of emerging economies not previously known for their high-technology industries have leapfrogged to the forefront in new Information Technologies ...

Breznitz, Dan

2005-01-01T23:59:59.000Z

267

National Residential Efficiency Measures Database Reduces Risk for Home Retrofit Industry (Fact Sheet), NREL Highlights, Research & Development  

SciTech Connect

A new database of residential building measures and estimated costs helps the U.S. building industry determine the most cost-effective means of improving efficiency of existing homes.

Not Available

2011-05-01T23:59:59.000Z

268

Using federal technology policy to strength the US microelectronics industry  

Science Conference Proceedings (OSTI)

A review of US and Japanese experiences with using microelectronics consortia as a tool for strengthening their respective industries reveals major differences. Japan has established catch-up consortia with focused goals. These consortia have a finite life targeted from the beginning, and emphasis is on work that supports or leads to product and process-improvement-driven commercialization. Japan`s government has played a key role in facilitating the development of consortia and has used consortia promote domestic competition. US consortia, on the other hand, have often emphasized long-range research with considerably less focus than those in Japan. The US consortia have searched for and often made revolutionary technology advancements. However, technology transfer to their members has been difficult. Only SEMATECH has assisted its members with continuous improvements, compressing product cycles, establishing relationships, and strengthening core competencies. The US government has not been a catalyst nor provided leadership in consortia creation and operation. We propose that in order to regain world leadership in areas where US companies lag foreign competition, the US should create industry-wide, horizontal-vertical, catch-up consortia or continue existing consortia in the six areas where the US lags behind Japan -- optoelectronics, displays, memories, materials, packaging, and manufacturing equipment. In addition, we recommend that consortia be established for special government microelectronics and microelectronics research integration and application. We advocate that these consortia be managed by an industry-led Microelectronics Alliance, whose establishment would be coordinated by the Department of Commerce. We further recommend that the Semiconductor Research Corporation, the National Science Foundation Engineering Research Centers, and relevant elements of other federal programs be integrated into this consortia complex.

Gover, J.E.; Gwyn, C.W.

1994-07-01T23:59:59.000Z

269

Development of prototype guidelines for risk management against terror attack in the tourism industry: a Delphi study  

E-Print Network (OSTI)

The purpose of the study was to gather strategies and factors from tourism security professionals from which terrorism risk management policies can be developed. This study utilized the Delphi method in order to provide structure for the group process. Twelve tourism security experts made up the panel completing three rounds of questionnaires via the email based Delphi technique. This research identified fifty-four strategies to reduce the propensity of terror attack at a tourism venue. Those strategies were divided into four levels of priority based on criticality and feasibility. The fifty-four strategies were grouped into nine subordinate categories. The subordinate categories were related to Training, Communications/ Liaison, Planning/ Assessment, Background Checks, ID Badges/ Secure Entrance, Specialty Security Units, Architectural Design, Media Cooperation, and Technology Based strategies. Alongside the strategies are a collection of comments by the experts regarding strengths, weaknesses, and any barriers to implementation pertaining to the individual strategy. Tourism risk managers, security personnel, and insurance underwriters can all use the results in reducing the opportunity for a terrorist attack at a tourism venue. Major research findings from this study included: 1. The strategy receiving the highest criticality ranking over all other strategies involves training first responders on their role in circumventing the success of terrorists. 2. The subordinate category Communication/ Liaison contains the largest number of strategies indicating the significance of this category among experts. 3. The subordinate category of Specialty Security Units contains the second highest number of strategies indicating the importance of the topic among experts. 4. All of the technology based strategies fell into the lowest priority level. Based on the findings of this study, researcher recommendations include: 1. The guidelines developed in this study should be used by operators of tourism venues to make the best use of limited resources. 2. National or international conferences should be established to further discuss these issues. 3. A greater number of communications mediums should be established to facilitate the exchange of ideas and experiences between affected professionals. 4. Insurance providers should use this information to establish validated guidelines so that, if prospective clients adhered to the recommendations, a reduction in premiums could be offered. 5. Other entities may benefit from this study, such as public school systems, the energy production industry, hospital systems, and pipeline systems.

Smith, Clifford Keith

2003-05-01T23:59:59.000Z

270

Users from Industry  

NLE Websites -- All DOE Office Websites (Extended Search)

Users from Industry Users from Industry Users from Industry Print The Advanced Light Source (ALS) welcomes industrial users from large and small companies whose projects advance scientific knowledge, investigate the development of new products and manufacturing methods, or provide economic benefits and jobs to the economy. The nature of industrial research can be different from traditional university and government sponsored projects, so the ALS has created unique opportunities for new and existing industrial users to access our user facilities and engage in productive relationships with our scientific and engineering staff. Examples of past and current research conducted at the ALS can be viewed on the Industry @ ALS Web page. There are several modes of access; the ALS User and Scientific Support Groups are especially committed to helping new industrial users gain a foothold in our user community and welcome inquiries about how to make that happen.

271

Development of a partnership with government and industry to accelerate the commercialization of hydrogen. Final report, November 1, 1996--October 31, 1997  

SciTech Connect

The National Hydrogen Association (NHA) was born out of a Hydrogen Workshop, November 16 and 17, 1988, held at the Electric Power Research Institute in Palo Alto, California. The following mission statement was adopted and remains the statement of the organization: to foster the development of hydrogen technologies and their utilization in industrial and commercial applications and to promote the transition role of hydrogen in the energy field. This final technical report provides a summary of the activities performed by the NHA. Activities are broken down by task area, and include the following: Information exchange within the NHA; Information exchange within the hydrogen industry; Information exchange with other critical industries and the public; Annual US hydrogen meeting; Codes and standards which includes establishing industry consensus on safety issues; Industry perspective and needs; and Administrative. Appendices to this report include the following: Role of the NHA in strategic planning for the hydrogen economy--An international initiative; Hydrogen safety report; and Implementation plan workshop II, whose purpose was to seek commercialization scenarios and strategies to introduce hydrogen in near-term transportation and power markets.

1998-09-01T23:59:59.000Z

272

Development of Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Iron and Steel Sector  

E-Print Network (OSTI)

1982. Energy and the Steel Industry, Brussels, Belgium:in the Canadian Steel Industry, Ottawa, Canada: CANMET.in the Iron and Steel Industry, in: Proceedings 1997 ACEEE

Xu, T.T.

2011-01-01T23:59:59.000Z

273

An Industrial-Based Consortium to Develop Premium Carbon Products from Coal, Annual Progress Report, October 1, 2003 through September 30, 2004  

SciTech Connect

Since 1998, The Pennsylvania State University (PSU) has been successfully operating the Consortium for Premium Carbon Products from Coal (CPCPC), which is a vehicle for industry-driven research on the promotion, development, and transfer of innovative technology on premium carbon produces from coal to the U.S. industry. The CPCPC is an initiative being led by PSU, its co-charter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provides the base funding for the program, with PSU responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity has continued under the present cooperative agreement, No. DE-FC26-03NT41874, which started October 1, 2003. The objective of the second agreement is to continue the successful operation of the CPCPC. The CPCPC has enjoyed tremendous success with its organizational structure, that includes PSU and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC is its industry-led council that selects proposals submitted by CPCPC members to ensure CPCPC target areas have strong industrial support. A second contract was executed with DOE NETL starting in October 2003 to continue the activities of CPCPC. An annual funding meeting was held in October 2003 and the council selected 10 projects for funding. Base funding for the projects is provided by NETL with matching funds from industry. Subcontracts were let from Penn State to the various subcontractors on March 1, 2004.

Andresen, John; Schobert, Harold; Miller, Bruce G

2006-03-01T23:59:59.000Z

274

Users from Industry  

NLE Websites -- All DOE Office Websites (Extended Search)

Users from Industry Print Users from Industry Print The Advanced Light Source (ALS) welcomes industrial users from large and small companies whose projects advance scientific knowledge, investigate the development of new products and manufacturing methods, or provide economic benefits and jobs to the economy. The nature of industrial research can be different from traditional university and government sponsored projects, so the ALS has created unique opportunities for new and existing industrial users to access our user facilities and engage in productive relationships with our scientific and engineering staff. Examples of past and current research conducted at the ALS can be viewed on the Industry @ ALS Web page. There are several modes of access; the ALS User and Scientific Support Groups are especially committed to helping new industrial users gain a foothold in our user community and welcome inquiries about how to make that happen.

275

National program plan for research and development in solar heating and cooling for building, agricultural, and industrial applications  

DOE Green Energy (OSTI)

The main feature of the directed program is the focus on specific approaches, called paths, to the application of solar energy. A path is the linking of a method of energy collection or rejection with a particular application. Eleven such paths are identified for building applications and eleven for agricultural and industrial process applications. Here, an overview is given of the program plan. The 11 paths to the solar heating and cooling of buildings and the 11 paths for agricultural and industrial process applications are described. Brief descriptions of these tasks and of the non-engineering tasks are included. The importance of each non-engineering task to the overall R and D program is indicated. (MHR)

Not Available

1978-08-01T23:59:59.000Z

276

Industry participation in DOE-sponsored geopressured geothermal resource development. Interim report, September 12, 1977-April 13, 1978  

DOE Green Energy (OSTI)

An industry forum for detailed discussions of the DOE resource evaluation program was instituted. An Overview Group was established along with four working subgroups - Site Selection, Drilling and Testing, Environmental/Laboratory Research, Legal/Institutional - at the initial forum meeting. All forum meetings are open to the public and are announced in the Federal Register. To date, 12 meetings have been conducted including two overview, two site selection, three drilling and testing, three environmental/laboratory research and two legal/institutional meetings. The meetings have been well attended. Representatives of 15 of the 19 largest US oil companies as well as 12 other major industrial firms have participated. In addition, 25 small businesses, 12 DOE contractors, 8 state agencies and 6 federal government agencies have been represented. Discussions have been open and spirited resulting in a useful interchange of ideas. The enthusiastic cooperation of the participants has demonstrated the ability of the government and industry to work harmoniously on programs aimed at solving the energy crisis.

Coffer, H.F.

1978-01-01T23:59:59.000Z

277

Industrial Buildings  

U.S. Energy Information Administration (EIA) Indexed Site

Industrial Industrial Industrial / Manufacturing Buildings Industrial/manufacturing buildings are not considered commercial, but are covered by the Manufacturing Energy Consumption Survey (MECS). See the MECS home page for further information. Commercial buildings found on a manufacturing industrial complex, such as an office building for a manufacturer, are not considered to be commercial if they have the same owner and operator as the industrial complex. However, they would be counted in the CBECS if they were owned and operated independently of the manufacturing industrial complex. Specific questions may be directed to: Joelle Michaels joelle.michaels@eia.doe.gov CBECS Manager Release date: January 21, 2003 Page last modified: May 5, 2009 10:18 AM http://www.eia.gov/consumption/commercial/data/archive/cbecs/pba99/industrial.html

278

Industrial Applications  

Science Conference Proceedings (OSTI)

Table 2   Frequently used rubber linings in other industries...Application Lining Power industry Scrubber towers Blended chlorobutyl Limestone slurry tanks Blended chlorobutyl Slurry piping Blended chlorobutyl 60 Shore A hardness natural rubber Seawater cooling water

279

Industries Affected  

Science Conference Proceedings (OSTI)

Table 2   Industries affected by microbiologically influenced corrosion...generation: nuclear, hydro, fossil fuel,

280

Industry Perspective  

NLE Websites -- All DOE Office Websites (Extended Search)

idatech.com idatech.com info@idatech.com 63065 NE 18 th Street Bend, OR 97701 541.383.3390 Industry Perspective Biogas and Fuel Cell Workshop National Renewable Energy Laboratory June 11 - 13, 2012 Mike Hicks Chairman of the Board of Directors, FCHEA Treasurer of the Board of Directors, FCS&E Engineering Manager, Technology Development & Integration, IdaTech Outline 1. Critical Factors * Fuel Purity * Fuel Cost 2. Natural Gas - The Wild Card & Competition 3. IdaTech's Experience Implementing Biofuel Critical Factor - Fuel Purity All fuel cell system OEMs have fuel purity specifications * Independent of * Raw materials or feed stocks * Manufacturing process * Depends on * Fuel processor technology * Fuel cell technology - low temp PEM versus SOFC

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Turning industry visions into reality  

Science Conference Proceedings (OSTI)

This brochure outlines the activities of the Office of Industrial Technologies (OIT) in the Department of Energy. OIT activities are aimed at industry adoption of energy-efficient, pollution-reducing technologies and include research and development on advanced technologies, financing, technical assistance, information dissemination, education, and bringing together industry groups, universities, National Laboratories, states, and environmentalists. OIT`s core initiative is to facilitate partnerships within seven materials and process industries: aluminum, chemicals, forest products, glass, metalcasting, petroleum refining, and steel industries.

NONE

1997-01-01T23:59:59.000Z

282

Development of an XUV-IR free-electron laser user facility for scientific research and industrial applications  

Science Conference Proceedings (OSTI)

Los Alamos has designed and proposes to establish an XUV-IR free- electron laser (FEL) user facility for scientific research and industrial applications based on coherent radiation ranging from soft x-rays as short as 1 nm to far-infrared wavelengths as long as 100 {mu}m. As the next-generation light source beyond low-emittance storage rings with undulator insertion devices, this proposed national FEL user facility should make available to researchers broadly tunable, picosecond-pulse, coherent radiation with 10{sup 4} to 10{sup 7} greater spectral flux and brightness. The facility design is based on two series of FEL oscillators including one regenerative amplifier. The primary series of seven FEL oscillators, driven by a single, 1-GeV rf linac, spans the short-wavelength range from 1 to 600 nm. A second 60-MeV rf linac, synchronized with the first, drives a series of three Vis/IR FEL oscillators to cover the 0. 5 to 100-{mu}m range. This paper presents the motivation for such a facility arising from its inherently high power per unit bandwidth and its potential use for an array of scientific and industrial applications, describes the facility design, output parameters, and user laboratories, makes comparisons with synchrotron radiation sources, and summarizes recent technical progress that supports the technical feasibility. 80 refs., 9 figs., 6 tabs.

Newnam, B.E.; Warren, R.W.; Conradson, S.D.; Goldstein, J.C.; McVey, B.D.; Schmitt, M.J.; Elliott, C.J.; Burns, M.J.; Carlsten, B.E.; Chan, K.C.; Johnson, W.J.; Wang, T.S.; Sheffield, R.L.; Meier, K.L.; Olsher, R.H.; Scott, M.L.; Griggs, J.E.

1991-01-01T23:59:59.000Z

283

NEW NIST MEDICAL-INDUSTRIAL RADIATION FACILITY ...  

Science Conference Proceedings (OSTI)

... NEW NIST MEDICAL-INDUSTRIAL RADIATION FACILITY WILL HELP DEVELOP NEW TECHNOLOGIES, ESTABLISH STANDARDS. ...

284

Country regulation of large scale commercial and industrial real estate development in the southwest : is it effective?  

E-Print Network (OSTI)

Real estate developers and county officials were surveyed to determine the existence, content and accessibility of county regulatory guidelines for land use and real estate development projects in the southwestern US. ...

Yates, Barrett Elizabeth

2006-01-01T23:59:59.000Z

285

Optoelectronics & Photonics  

Science Conference Proceedings (OSTI)

At the same time, we will demonstrate E-field modulation of anisotropic magnetoresistance, giant magnetoresistance and exchange bias at room temperature in...

286

An Industrial-Based Consortium to Develop Premium Carbon Products from Coal, Annual Progress Report, October 1, 2004 through September 30, 2005  

SciTech Connect

Since 1998, The Pennsylvania State University (PSU) has been successfully operating the Consortium for Premium Carbon Products from Coal (CPCPC), which is a vehicle for industry-driven research on the promotion, development, and transfer of innovative technology on premium carbon produces from coal to the U.S. industry. The CPCPC is an initiative being led by PSU, its co-charter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provides the base funding for the program, with PSU responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity has continued under the present cooperative agreement, No. DE-FC26-03NT41874, which started October 1, 2003. The objective of the second agreement is to continue the successful operation of the CPCPC. The CPCPC has enjoyed tremendous success with its organizational structure, that includes PSU and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC is its industry-led council that selects proposals submitted by CPCPC members to ensure CPCPC target areas have strong industrial support. A second contract was executed with DOE NETL starting in October 2003 to continue the activities of CPCPC. An annual funding meeting was held in October 2003 and the council selected ten projects for funding. Base funding for the projects is provided by NETL with matching funds from industry. Subcontracts were let from Penn State to the subcontractors on March 1, 2004. Nine of the ten projects have been completed and the final reports for these 2004 projects are attached. An annual funding meeting was held in November 2004 and the council selected eleven projects for funding. Subcontracts were let from Penn State to the subcontractors on March 1, 2005. Three additional projects were selected for funding during the April 2005 tutorial/funding meeting. Subcontracts were let from Penn State to the subcontractors on July 1, 2005.

Miller, Bruce G

2006-03-01T23:59:59.000Z

287

An Industrial-Based Consortium to Develop Premium Carbon Products from Coal, Annual Progress Report, October 1, 2005 through September 30, 2006  

Science Conference Proceedings (OSTI)

Since 1998, The Pennsylvania State University has been successfully managing the Consortium for Premium Carbon Products from Coal (CPCPC), which is a vehicle for industry-driven research on the promotion, development, and transfer of innovative technology on premium carbon produces from coal to the U.S. industry. The CPCPC is an initiative being led by Penn State, its co-charter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provides the base funding for the program, with Penn State responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity has continued under the present cooperative agreement, No. DE-FC26-03NT41874, which started October 1, 2003. The objective of the second agreement is to continue the successful operation of the CPCPC. The CPCPC has enjoyed tremendous success with its organizational structure, that includes Penn State and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC is its industry-led council that selects proposals submitted by CPCPC members to ensure CPCPC target areas have strong industrial support. Base funding for the selected projects is provided by NETL with matching funds from industry. At the annual funding meeting held in October 2003, ten projects were selected for funding. Subcontracts were let from Penn State to the subcontractors on March 1, 2004. Nine of the ten 2004 projects were completed during the previous annual reporting period and their final reports were submitted with the previous annual report (i.e., 10/01/04-09/30/05). The final report for the remaining project, which was submitted during this reporting period (i.e., 10/01/05-09/30/06), is attached. At the annual funding meeting held in November 2004, eleven projects were selected for funding. Subcontracts were let from Penn State to the subcontractors on March 1, 2005. Three additional projects were selected for funding during the April 2005 tutorial/funding meeting. Subcontracts were let from Penn State to the subcontractors on July 1, 2005. Of these fourteen 2005 projects, eleven have been completed and the final reports are attached. An annual funding meeting was held in November 2005 and the council selected five projects for funding. Subcontracts were let from Penn State to the subcontractors on March 1, 2006, except for one that started October 1, 2006.

Miller, Bruce G

2006-09-29T23:59:59.000Z

288

Carbon Based Nano-Materials Research, Development and Applications in Optoelectronics  

E-Print Network (OSTI)

Appl. Phys. Lett 73, Dai, H. Carbon Nanotubes: Synthesis,Martel, R. & Wind, S. J. Carbon Nanotube Electronics. Proc.Chen, Z. & Perebeinos, V. Carbon-Based Electronics. Nat.

Wang, Feihu

2012-01-01T23:59:59.000Z

289

Carbon Based Nano-Materials Research, Development and Applications in Optoelectronics  

E-Print Network (OSTI)

Semiconducting Carbon Nanotubes. Nano Lett. 4, 35-39 (2004).on Clean Substrates. Nano Lett. 9, 3137-3141 Dalton, A. B.Single-Wall Carbon Nanotube. Nano Lett. 5, Wu, Z. et al.

Wang, Feihu

2012-01-01T23:59:59.000Z

290

Industry @ ALS  

NLE Websites -- All DOE Office Websites (Extended Search)

Industry @ ALS Industry @ ALS Industry @ ALS Concrete Industry Benefits from Ancient Romans and the ALS Print Thursday, 17 October 2013 14:24 New insights into the Romans' ingenious concrete harbor structures emerging from ALS beamline research could move the modern concrete industry toward its goal of a reduced carbon footprint. Summary Slide Read more... Moving Industry Forward: Finding the Environmental Opportunity in Biochar Print Thursday, 12 September 2013 08:41 Using ALS Beamlines 10.3.2 and 8.3.2, the Environmental Protection Agency (EPA) is currently investigating how biochar sorbs environmental toxins and which kinds of biochar are the most effective. The possibilities for widespread use have already launched entrepreneurial commercial ventures. Summary Slide

291

Biodiesel Industries Inc | Open Energy Information  

Open Energy Info (EERE)

Industries Inc Place Santa Barbara, California Zip 93110 Product Biodiesel producer and facility developer. References Biodiesel Industries Inc1 LinkedIn Connections CrunchBase...

292

Kishimura Industry Co | Open Energy Information  

Open Energy Info (EERE)

Kishimura Industry Co Jump to: navigation, search Name Kishimura Industry Co Place Kanagawa-Ken, Japan Sector Solar, Vehicles Product Developer of solar power systems and...

293

NREL: TroughNet - Industry Partners  

NLE Websites -- All DOE Office Websites (Extended Search)

the solar energy industry that partner with the U.S. Department of Energy's SunLab on parabolic trough technology research, development, and deployment efforts. Industry Partner...

294

Industrial Partnerships - Oak Ridge National Laboratory | ORNL  

Manager; Tom Rogers: Director, Industrial and Economic Development Partnerships: rogerstc@ornl.gov (865) 241-2149: bio: Staff Members; Tammy Barnhart: Industrial and ...

295

Environmental Protection- Industrial Compliance (Newfoundland and Labrador, Canada)  

Energy.gov (U.S. Department of Energy (DOE))

The Industrial Compliance Section develops and administers Certificates of Approval for the Construction and/or Operation of various industrial facilities. Industries with air emissions and/or...

296

A Study to Develop an Industrial-Scale, Computer-Controlled High Magnetic Field Processing (HMFP) System to Assist in Commercializing the Novel, Enabling HMFP Manufacturing Technology  

SciTech Connect

As the original magnet designer and manufacturer of ORNLs 9T, 5-inch ID bore magnet, American Magnetics Inc. (AMI) has collaborated with ORNLs Materials Processing Groups and this partnership has been instrumental in the development of our unique thermo-magnetic facilities and expertise. Consequently, AMI and ORNL have realized that the commercial implementation of the High Magnetic Field Processing (HMFP) technology will require the evolution of robust, automated superconducting (SC) magnet systems that will be cost-effective and easy to operate in an industrial environment. The goal of this project and CRADA is to significantly expedite the timeline for implementing this revolutionary and pervasive cross-cutting technology for future US produced industrial components. The successful completion of this project is anticipated to significantly assist in the timely commercialization and licensing of our HMFP intellectual property for a broad spectrum of industries; and to open up a new market for AMI. One notable outcome of this project is that the ThermoMagnetic Processing Technology WON a prestigious 2009 R&D 100 Awards. This award acknowledges and recognizes our TMP Technology as one of the top 100 innovative US technologies in 2009. By successfully establishing the design requirements for a commercial scale magnetic processing system, this project effort has accomplished a key first step in facilitating the building and demonstration of a superconducting magnetic processing coil, enabling the transition of the High Magnetic Field Processing Technology beyond a laboratory novelty into a commercially viable and industrially scalable Manufacturing Technology.

Lutdka, G. M.; Chourey, A. (American Magnetics, Inc.)

2010-05-12T23:59:59.000Z

297

Industrial Oil Products Division  

Science Conference Proceedings (OSTI)

A forum for professionals involved in research, development, engineering, marketing, and testing of industrial products and co-products from fats and oils, including fuels, lubricants, coatings, polymers, paints, inks, cosmetics, dielectric fluids, and ad

298

Industrial Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Module. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code.

Kelly Perl

2013-05-14T23:59:59.000Z

299

Optimization of Industrial Enzymes  

Enzymes are highly efficient naturally occurring catalysts that are used in a wide range of applications from industrial processes to new drug development. Conventional mechanism for understanding the mechanisms of enzyme functions are costly and time ...

300

Industrial Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Module. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code.

Kelly Perl

2013-09-30T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

DSENT - A Tool Connecting Emerging Photonics with Electronics for Opto-Electronic Networks-on-Chip Modeling  

E-Print Network (OSTI)

With the advent of many-core chips that place substantial demand on the NoC, photonics has been investigated as a promising alternative to electrical NoCs. While numerous opto-electronic NoCs have been proposed, their ...

Sun, Chen

2012-02-08T23:59:59.000Z

302

Development of mineral wool from industrial wastes. Phase i. Final report 1 Sep 80-28 Feb 81  

SciTech Connect

The feasibility of using unprocessed industrial wastes to produce mineral wool was investigated by literature and patent searches and by experimental production of mineral wool. Slag ash from coal burning utilities and cement kiln waste from cement companies were combined in batch formulations having acid to alkali ratios of 0.8 to 1.2, then melted, fiberized, and analyzed for physical, thermal, chemical, and optical properties. Cement kiln waste added to the slag ash in controlled quantities served as a fluxing agent, and lowered the melting point of the slag ash from 2800 degrees F to 2500 degrees F. The softening point of the fibers was between 1250 degrees F and 1480 degrees F. The surface of the fibers was smooth at a magnification of 800x, and X-ray analysis showed no crystallization. The glasses were chemically stable, and possessed the rheological properties necessary to produce mineral wool. Potential applications include using the mineral wool for insulation. Immersion in cement slurry for 24 hours did not affect the fibers, indicating that they might also be used as alkali resistant components for fiber-reinforced concrete.

Ali, M.A.

1981-02-01T23:59:59.000Z

303

Software Development, Modeling, and Analysis: We're Developing Advanced Design Tools to Support the Wind Industry with "State-of-the-Art" Analysis Capability (Fact Sheet)  

SciTech Connect

This fact sheet provides an overview of the software development, modeling, and analysis for wind turbine performance, loads, and stabiluty analysis.

2010-01-01T23:59:59.000Z

304

Software Development, Modeling, and Analysis: We're Developing Advanced Design Tools to Support the Wind Industry with "State-of-the-Art" Analysis Capability (Fact Sheet)  

DOE Green Energy (OSTI)

This fact sheet provides an overview of the software development, modeling, and analysis for wind turbine performance, loads, and stabiluty analysis.

Not Available

2010-01-01T23:59:59.000Z

305

Aluminum: Industry of the future  

SciTech Connect

For over a century, the US aluminum industry has led the global market with advances in technology, product development, and marketing. Industry leaders recognize both the opportunities and challenges they face as they head into the 21st century, and that cooperative R and D is key to their success. In a unique partnership, aluminum industry leaders have teamed with the US Department of Energy`s Office of Industrial Technologies (OIT) to focus on innovative technologies that will help to strengthen the competitive position of the US aluminum industry and, at the same time, further important national goals. This industry-led partnership, the Aluminum Industry of the Future, promotes technologies that optimize the use of energy and materials in operations and reduce wastes and energy-related emissions. Led by The Aluminum Association, industry leaders began by developing a unified vision of future market, business, energy, and environmental goals. Their vision document, Partnerships for the Future, articulates a compelling vision for the next 20 years: to maintain and grow the aluminum industry through the manufacture and sale of competitively priced, socially desirable, and ecologically sustainable products. Continued global leadership in materials markets will require the combined resources of industry, universities, and government laboratories. By developing a unified vision, the aluminum industry has provided a framework for the next step in the Industries of the Future process, the development of a technology roadmap designed to facilitate cooperative R and D.

1998-11-01T23:59:59.000Z

306

Solar energy industry survey  

SciTech Connect

This report describes the results of a survey of companies in the solar energy industry. The general objective of the survey was to provide information to help evaluate the effectiveness of technology transfer mechanisms for the development of the solar industry. The specific objectives of the survey included: (1) determination of the needs of the solar industry; (2) identification of special concerns of the solar industry; and (3) determination of the types of technology transfer mechanisms that would be most helpful to the solar industry in addressing these needs and concerns. The major focus was on technical problems and developments, but institutional and marketing considerations were also treated. The majority of the sample was devoted to the solar heating and cooling (SHAC) component of the industry. However, a small number of photovoltaic (PV), wind, and power generation system manufacturers were also surveyed. Part I discusses the methodology used in the selection, performance, and data reduction stages of the survey, comments on the nature of the responses, and describes the conclusions drawn from the survey. The latter include both general conclusions concerning the entire solar industry, and specific conclusions concerning component groups, such as manufacturers, architects, installers, or dealers. Part II consists of tabulated responses and non-attributed verbatim comments that summarize and illustrate the survey results.

1979-08-06T23:59:59.000Z

307

A World-Class University-Industry Consortium for Wind Energy Research, Education, and Workforce Development: Final Technical Report  

Science Conference Proceedings (OSTI)

During the two-year project period, the consortium members have developed control algorithms for enhancing the reliability of wind turbine components. The consortium members have developed advanced operation and planning tools for accommodating the high penetration of variable wind energy. The consortium members have developed extensive education and research programs for educating the stakeholders on critical issues related to the wind energy research and development. In summary, The Consortium procured one utility-grade wind unit and two small wind units. Specifically, the Consortium procured a 1.5MW GE wind unit by working with the world leading wind energy developer, Invenergy, which is headquartered in Chicago, in September 2010. The Consortium also installed advanced instrumentation on the turbine and performed relevant turbine reliability studies. The site for the wind unit is Invenergy???????¢????????????????s Grand Ridge wind farmin Illinois. The Consortium, by working with Viryd Technologies, installed an 8kW Viryd wind unit (the Lab Unit) at an engineering lab at IIT in September 2010 and an 8kW Viryd wind unit (the Field Unit) at the Stuart Field on IIT???????¢????????????????s main campus in July 2011, and performed relevant turbine reliability studies. The operation of the Field Unit is also monitored by the Phasor Measurement Unit (PMU) in the nearby Stuart Building. The Consortium commemorated the installations at the July 20, 2011 ribbon-cutting ceremony. The Consortium???????¢????????????????s researches on turbine reliability included (1) Predictive Analytics to Improve Wind Turbine Reliability; (2) Improve Wind Turbine Power Output and Reduce Dynamic Stress Loading Through Advanced Wind Sensing Technology; (3) Use High Magnetic Density Turbine Generator as Non-rare Earth Power Dense Alternative; (4) Survivable Operation of Three Phase AC Drives in Wind Generator Systems; (5) Localization of Wind Turbine Noise Sources Using a Compact Microphone Array; (6) Wind Turbine Acoustics - Numerical Studies; and (7) Performance of Wind Turbines in Rainy Conditions. The Consortium???????¢????????????????s researches on wind integration included (1) Analysis of 2030 Large-Scale Wind Energy Integration in the Eastern Interconnection; (2) Large-scale Analysis of 2018 Wind Energy Integration in the Eastern U.S. Interconnection; (3) Integration of Non-dispatchable Resources in Electricity Markets; (4) Integration of Wind Unit with Microgrid. The Consortium???????¢????????????????s education and outreach activities on wind energy included (1) Wind Energy Training Facility Development; (2) Wind Energy Course Development; (3) Wind Energy Outreach.

Shahidehpour, Mohammad

2012-10-30T23:59:59.000Z

308

AMO Industrial Distributed Energy: Partnerships  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

energy efficiency by 2020. The Industrial Energy EfficiencyCombined Heat & Power Working Group is developing a number of resources. News Energy Department Invests in...

309

NREL: Energy Storage - Industry Participants  

NLE Websites -- All DOE Office Websites (Extended Search)

Industry Participants NREL's energy storage project is funded by the DOE's Vehicle Technologies Office. We work closely with automobile manufacturers, energy storage developers,...

310

Development and testing of a high efficiency advanced coal combustor: Phase 3 industrial boiler retrofit. Final report  

SciTech Connect

Economics and/or political intervention may one day dictate the conversion from oil or natural gas to coal in boilers that were originally designed to burn oil or gas. In recognition of this future possibility the US Department of Energy, Federal Energy Technical Center (DOE-FETC) supported a program led by ABB Power Plant Laboratories with support from the Energy and Fuels Research Center of Penn State University with the goal of demonstrating the technical and economic feasibility of retrofitting a gas/oil designed boiler to burn micronized coal. In support of the overall goal the following specific objectives were targeted: develop a coal handling/preparation system that can meet the technical and operational requirements for retrofitting microfine coal on a boiler designed for burning oil or natural gas; maintain boiler thermal performance in accordance with specifications when burning oil or natural gas; maintain NOx emissions at or below 0.6 lb NO{sub 2} per million Btu; achieve combustion efficiencies of 98% or higher; and determine economic payback periods as a function of key variables.

Patel, R.L.; Thornock, D.E.; Miller, B.G.; Scaroni, A.W.; McGowan, J.G.

1998-03-01T23:59:59.000Z

311

Texas Industries of the Future  

E-Print Network (OSTI)

The purpose of the Texas Industries of the Future program is to facilitate the development, demonstration and adoption of advanced technologies and adoption of best practices that reduce industrial energy usage, emissions, and associated costs, resulting in improved competitive performance. The bottom line for Texas industry is savings in energy and materials, cost-effective environmental compliance, increased productivity, reduced waste, and enhanced product quality. The state program leverages the programs and tools of the federal Department of Energy's Industries of the Future. At the federal level, there are nine Industries of the Future: refining, chemicals, aluminum, steel, metal casting, glass, mining, agriculture, and forest products. These industries were selected nationally because they supply over 90% of the U.S. economy's material needs and account for 75% of all energy use by U.S. industry. In Texas, three IOF sectors, chemicals, refining and forest products, account for 86% of the energy used by industry in this state.

Ferland, K.

2002-04-01T23:59:59.000Z

312

Development of Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Iron and Steel Sector  

Science Conference Proceedings (OSTI)

Adoption of efficient end-use technologies is one of the key measures for reducing greenhouse gas (GHG) emissions. With the working of energy programs and policies on carbon regulation, how to effectively analyze and manage the costs associated with GHG reductions become extremely important for the industry and policy makers around the world. Energy-climate (EC) models are often used for analyzing the costs of reducing GHG emissions (e.g., carbon emission) for various emission-reduction measures, because an accurate estimation of these costs is critical for identifying and choosing optimal emission reduction measures, and for developing related policy options to accelerate market adoption and technology implementation. However, accuracies of assessing of GHG-emission reduction costs by taking into account the adoption of energy efficiency technologies will depend on how well these end-use technologies are represented in integrated assessment models (IAM) and other energy-climate models. In this report, we first conduct brief overview on different representations of end-use technologies (mitigation measures) in various energy-climate models, followed by problem statements, and a description of the basic concepts of quantifying the cost of conserved energy including integrating non-regrets options. A non-regrets option is defined as a GHG reduction option that is cost effective, without considering their additional benefits related to reducing GHG emissions. Based upon these, we develop information on costs of mitigation measures and technological change. These serve as the basis for collating the data on energy savings and costs for their future use in integrated assessment models. In addition to descriptions of the iron and steel making processes, and the mitigation measures identified in this study, the report includes tabulated databases on costs of measure implementation, energy savings, carbon-emission reduction, and lifetimes. The cost curve data on mitigation measures are available over time, which allows an estimation of technological change over a decade-long historical period. In particular, the report will describe new treatment of technological change in energy-climate modeling for this industry sector, i.e., assessing the changes in costs and energy-savings potentials via comparing 1994 and 2002 conservation supply curves. In this study, we compared the same set of mitigation measures for both 1994 and 2002 -- no additional mitigation measure for year 2002 was included due to unavailability of such data. Therefore, the estimated potentials in total energy savings and carbon reduction would most likely be more conservative for year 2002 in this study. Based upon the cost curves, the rate of change in the savings potential at a given cost can be evaluated and be used to estimate future rates of change that can be the input for energy-climate models. Through characterizing energy-efficiency technology costs and improvement potentials, we have developed and presented energy cost curves for energy efficiency measures applicable to the U.S. iron and steel industry for the years 1994 and 2002. The cost curves can change significantly under various scenarios: the baseline year, discount rate, energy intensity, production, industry structure (e.g., integrated versus secondary steel making and number of plants), efficiency (or mitigation) measures, share of iron and steel production to which the individual measures can be applied, and inclusion of other non-energy benefits. Inclusion of other non-energy benefits from implementing mitigation measures can reduce the costs of conserved energy significantly. In addition, costs of conserved energy (CCE) for individual mitigation measures increase with the increases in discount rates, resulting in a general increase in total cost of mitigation measures for implementation and operation with a higher discount rate. In 1994, integrated steel mills in the U.S. produced 55.

Xu, T.T.; Sathaye, J.; Galitsky, C.

2010-09-30T23:59:59.000Z

313

Industry - ORNL Neutron Sciences  

NLE Websites -- All DOE Office Websites (Extended Search)

Former User Group Chair Enthusiastic About Relevance of Neutron Scattering Former User Group Chair Enthusiastic About Relevance of Neutron Scattering to Industrial Research Former User Group Chair Mike Crawford Mike Crawford, DuPont Research and Development. The drive is intensifying to encourage research partnerships between Neutron Sciences and private industry. Such partnerships, a long-term strategic goal set by the DOE's Basic Energy Sciences Advisory Committee, will deliver industry and its technological problems to SNS and HFIR, where joint laboratory-industry teams can use the unparalleled resources available here to resolve them. "SNS is a tremendous facility. It has the potential to have a couple of thousand user visits a year and, if they build another target station in the future, you're probably talking about 4000 user visits a year,"

314

Outlook for Industrial Energy Benchmarking  

E-Print Network (OSTI)

The U.S. Environmental Protection Agency is exploring options to sponsor an industrial energy efficiency benchmarking study to identify facility specific, cost-effective best practices and technologies. Such a study could help develop a common understanding of opportunities for energy efficiency improvements and provide additional information to improve the competitiveness of U.S. industry. The EPA's initial benchmarking efforts will focus on industrial power facilities. The key industries of interest include the most energy intensive industries, such as chemical, pulp and paper, and iron and steel manufacturing.

Hartley, Z.

2000-04-01T23:59:59.000Z

315

Financing the growth of energy efficiency service industry in Shanghai  

E-Print Network (OSTI)

present experiences of energy service industrial developmentNational Association of Energy Service Companies (NAESCO),2004, Developing an Energy Efficiency Service Industry in

Lin, Jiang; Gilligan, Donald; Zhao, Yinghua

2005-01-01T23:59:59.000Z

316

Microscopy Technique Could Help Computer Industry ...  

Science Conference Proceedings (OSTI)

Microscopy Technique Could Help Computer Industry Develop 3-D Components. From NIST Tech Beat: June 25, 2013. ...

2013-06-25T23:59:59.000Z

317

Developments in the Magnesium Industry  

Science Conference Proceedings (OSTI)

Transfer and Consumption of Oxygen in Gold-bearing Sulfide Ores: Agnico-eagle Mines Trials Tundish Process Performance Improvement: Some Indian Case...

318

Industrial Business Development Program Office  

Los Alamos National Laboratory, a Department of Energy (DOE) National Nuclear Security Administration (NNSA) laboratory, managed by the University of California, is

319

Development of Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Iron and Steel Sector  

E-Print Network (OSTI)

Leonhard (eds. ), Energy Efficiency Improvements in ElectricC. Moore, 1997. Energy Efficiency and Advanced TechnologiesSummer Study on Energy Efficiency in Industry, Washington,

Xu, T.T.

2011-01-01T23:59:59.000Z

320

Associations and Industry - TMS  

Science Conference Proceedings (OSTI)

... Associations and Industry, Research Programs, ==== Basic Metallurgy ==== ... FORUMS > ASSOCIATIONS AND INDUSTRY, Replies, Views, Originator, Last...

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Industrial alliances  

Science Conference Proceedings (OSTI)

The United States is emerging from the Cold War era into an exciting, but challenging future. Improving the economic competitiveness of our Nation is essential both for improving the quality of life in the United States and maintaining a strong national security. The research and technical skills used to maintain a leading edge in defense and energy now should be used to help meet the challenge of maintaining, regaining, and establishing US leadership in industrial technologies. Companies recognize that success in the world marketplace depends on products that are at the leading edge of technology, with competitive cost, quality, and performance. Los Alamos National Laboratory and its Industrial Partnership Center (IPC) has the strategic goal to make a strong contribution to the nation`s economic competitiveness by leveraging the government`s investment at the Laboratory: personnel, infrastructure, and technological expertise.

Adams, K.V.

1993-09-13T23:59:59.000Z

322

Synfuels industry opportunities  

SciTech Connect

Presentations made at the seminar are included in this volume. The present state in the development of synthetic fuels and the creation of the Synthetic Fuels Corporation are discussed by representatives of federal agencies and private industry. Separate abstracts of individual items were prepared for inclusion in the Energy Data Base and Energy Abstracts for Policy Analysis. (DMC)

Hill, R.F.; Boardman, E.B.; Heavner, M.L. (eds.)

1981-01-01T23:59:59.000Z

323

An Industry/DOE Program to Develop and Benchmark Advanced Diamond Product Drill Bits and HP/HT Drilling Fluids to Significantly Improve Rates of Penetration  

Science Conference Proceedings (OSTI)

A deep drilling research program titled 'An Industry/DOE Program to Develop and Benchmark Advanced Diamond Product Drill Bits and HP/HT Drilling Fluids to Significantly Improve Rates of Penetration' was conducted at TerraTek's Drilling and Completions Laboratory. Drilling tests were run to simulate deep drilling by using high bore pressures and high confining and overburden stresses. The purpose of this testing was to gain insight into practices that would improve rates of penetration and mechanical specific energy while drilling under high pressure conditions. Thirty-seven test series were run utilizing a variety of drilling parameters which allowed analysis of the performance of drill bits and drilling fluids. Five different drill bit types or styles were tested: four-bladed polycrystalline diamond compact (PDC), 7-bladed PDC in regular and long profile, roller-cone, and impregnated. There were three different rock types used to simulate deep formations: Mancos shale, Carthage marble, and Crab Orchard sandstone. The testing also analyzed various drilling fluids and the extent to which they improved drilling. The PDC drill bits provided the best performance overall. The impregnated and tungsten carbide insert roller-cone drill bits performed poorly under the conditions chosen. The cesium formate drilling fluid outperformed all other drilling muds when drilling in the Carthage marble and Mancos shale with PDC drill bits. The oil base drilling fluid with manganese tetroxide weighting material provided the best performance when drilling the Crab Orchard sandstone.

TerraTek

2007-06-30T23:59:59.000Z

324

Industrial lighting handbook  

SciTech Connect

Technological advances in industrial lighting system components now make it possible to reduce lighting system consumption by up to 50% or more without loss of the benefits inherent in good quality electric illumination. Management involvement in decisions about industrial lighting is essential, however, and this document provides generalized information in lay terms to help decision-makers become familiar with the concerns that affect industrial environment and the financial well-being of their companies. The five sections (1) discuss the benefits of good lighting, (2) review certain major lighting issues and terms, (3) identify procedures for developing a lighting energy management plan, (4) identify lighting energy management options (LEMOs), and (5) discuss sources of assistance. 19 figures, 8 tables.

1985-01-01T23:59:59.000Z

325

Development of Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Iron and Steel Sector  

E-Print Network (OSTI)

energy savings with discounts rates 10%, 20% and 30% in the U.S. iron and steel industryenergy savings with discounts rates 10%, 20% and 30% in the U.S. iron and steel industry.

Xu, T.T.

2011-01-01T23:59:59.000Z

326

Industrial Distributed Energy: Combined Heat & Power  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

(DOE) (DOE) Industrial Technology Program (ITP) Industrial Distributed Energy: Combined Heat & Power (CHP) Richard Sweetser Senior Advisor DOE's Mid-Atlantic Clean Energy Application Center 32% Helping plants save energy today using efficient energy management practices and efficient new technologies Activities to spur widespread commercial use of CHP and other distributed generation solutions 10% Manufacturing Energy Systems 33% Industries of the Future R&D addressing top priorities in America's most energy-intensive industries and cross-cutting activities applicable to multiple industrial subsectors 25% Industrial Distributed Energy Industrial Technical Assistance DOE ITP FY'11 Budget: $100M Knowledge development and

327

Ceramic Industries, Non-ferrous  

E-Print Network (OSTI)

Refractory applications for the steel, non-ferrous and cement industry Refractory applications for the ceramic, petrochemical and other industry Raw materials for refractories Users points of view Quality and Environment Processes, equipment and controls Development of refractory products

Refractories For Iron; Hydrocarbon Waste Incineration Pulp

2005-01-01T23:59:59.000Z

328

Transforming the Freight Industry  

E-Print Network (OSTI)

Transforming the Freight Industry From Regulation to Icommon-carrier freight industry was Competition to backwardjourneys. When the freight industry was deregulated, it was

Regan, Amelia

2002-01-01T23:59:59.000Z

329

Demographics and industry returns  

E-Print Network (OSTI)

Demographics and Industry Returns By Stefano DellaVigna andand returns across industries. Cohort size fluc- tuationspredict profitability by industry. Moreover, forecast demand

Pollet, Joshua A.; DellaVigna, Stefano

2007-01-01T23:59:59.000Z

330

Edible Oleogels: Structure and Health ImplicationsChapter 6 Candelilla Wax as an Organogelator for Vegetable OilsAn Alternative to Develop trans-free Products for the Food Industry  

Science Conference Proceedings (OSTI)

Edible Oleogels: Structure and Health Implications Chapter 6 Candelilla Wax as an Organogelator for Vegetable OilsAn Alternative to Develop trans-free Products for the Food Industry Food Science eChapters Food Science & Technology A2C008

331

Virginia Regional Industrial Facilities Act (Virginia) | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Regional Industrial Facilities Act (Virginia) Regional Industrial Facilities Act (Virginia) Virginia Regional Industrial Facilities Act (Virginia) < Back Eligibility Commercial Construction Developer Industrial Investor-Owned Utility Local Government Municipal/Public Utility Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Virginia Program Type Industry Recruitment/Support Provider Regional Industrial Facility Authorities The Virginia Regional Industrial Facilities Act is meant to aid the economic development of localities within the Commonwealth. The Act provides a mechanism for localities to establish regional industrial facility authorities, enabling them to pool financial resources to stimulate economic development. The purpose of a regional industrial

332

Research Projects in Industrial Technology.  

Science Conference Proceedings (OSTI)

The purpose of this booklet is to briefly describe ongoing and completed projects being carried out by Bonneville Power Administration's (BPA) Industrial Technology Section. In the Pacific Northwest, the industrial sector is the largest of the four consuming sectors. It accounted for thirty-nine percent of the total firm demand in the region in 1987. It is not easy to asses the conservation potential in the industrial sector. Recognizing this, the Northwest Power Planning Council established an objective to gain information on the size, cost, and availability of the conservation resource in the industrial sector, as well as other sectors, in its 1986 Power Plan. Specifically, the Council recommended that BPA operate a research and development program in conjunction with industry to determine the potential costs and savings from efficiency improvements in industrial processes which apply to a wide array of industrial firms.'' The section, composed of multidisciplinary engineers, provides technical support to the Industrial Programs Branch by designing and carrying out research relating to energy conservation in the industrial sector. The projects contained in this booklet are arranged by sector --industrial, utility, and agricultural -- and, within each sector, chronologically from ongoing to completed, with those projects completed most recently falling first. For each project the following information is given: its objective approach, key findings, cost, and contact person. Completed projects also include the date of completion, a report title, and report number.

United States. Bonneville Power Administration. Industrial Technology Section.

1990-06-01T23:59:59.000Z

333

Development and testing of a high efficiency advanced coal combustor: Phase 3, industrial boiler retrofit. Quarterly technical progress report number 12, July 1, 1994--September 30, 1994  

SciTech Connect

The objective of this project is to retrofit the previously developed High Efficiency Advanced Coal Combustor (HEACC) to a standard gas/oil designed industrial boiler to assess the technical and economic viability of displacing premium fuels with microfine coal. During this reporting period, data reduction/evaluation and interpretation from the long term four hundred hours Proof-of-Concept System Test under Task 3 were completed. Cumulatively, a total of approximately 563 hours of coal testing was performed with 160 hrs on 100% coal and over 400 hours with co-firing coal and gas. The primary objectives of this testing were to: (1) obtain steady state operation consistently on 100% coal; (2) increase carbon conversion efficiency from 95% to the project goal of 98%; and (3) maintain NOx emissions at or below 0.6 lbs/MBtu. The following specific conclusions are based on results of coal-fired testing at Penn State and the initial economic evaluation of the HEACC system: a coal handling/preparation system can be designed to meet the technical requirements for retrofitting microfine coal combustion to a gas/oil-designed boiler; the boiler thermal performance requirements were met; the NOx emission target of was met; combustion efficiencies of 95% could be met on a daily average basis, somewhat below the target of 98%; the economic playback is very sensitive to fuel differential cost, unit size, and annual operating hours; continuous long term demonstration is needed to quantify ash effects and how to best handle ashes. The following modifications are recommended prior to the 1,000 hour demonstration phase testing: (1) coal feeding improvements--improved raw coal/storage and transport, installation of gravimetric feeder, and redesign/installation of surge bin bottom; (2) burner modification--minor modification to the tip of the existing HEACC burner to prevent change of flame shapes for no apparent reason.

Patel, R.L.; Borio, R. [ABB/Combustion Engineering, Windsor, CT (United States). Power Plant Labs.; Scaroni, A.W.; Miller, B.G. [Pennsylvania State Univ., University Park, PA (United States); McGowan, J.G. [Univ. of Massachusetts, Amherst, MA (United States)

1994-11-18T23:59:59.000Z

334

Materials needs and opportunities in the pulp and paper industry  

SciTech Connect

The Department of Energy`s (DOE) Office of Industrial Technologies (OIT) supports research and development (R&D) in industry, the DOE national laboratories, and in universities to develop energy efficient, environmentally-acceptable industrial technologies. The Office of Industrial Technologies is working with seven energy-intensive industries to develop R&D roadmaps that will facilitate cooperative government-industry efforts to achieve energy-efficient, environmentally-acceptable, sustainable industries of the future. The forest products industry is one of the industries with which OIT is working to develop an R&D roadmap. The Advanced Industrial Materials (AIM) Program of the Office of Industrial Technologies sponsors long-term, directed research on materials that will enable industry to develop and utilize more energy-efficient, sustainable processes and technologies. The purpose of the study described in this report was to identify the material R&D needs and opportunities for the pulp and paper mill of the future.

Angelini, P. [comp.

1995-08-01T23:59:59.000Z

335

New Recovery Act Funding Boosts Industrial Carbon Capture and...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act Funding Boosts Industrial Carbon Capture and Storage Research and Development New Recovery Act Funding Boosts Industrial Carbon Capture and Storage Research and...

336

Power Plant and Industrial Fuel Use Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Plant and Industrial Fuel Use Act Power Plant and Industrial Fuel Use Act Electricity Advisory Committee Technology Development Electricity Policy Coordination and...

337

Thinking Globally: How ISO 50001 - Energy Management can make industrial energy efficiency standard practice  

E-Print Network (OSTI)

Tracking Industrial Energy Efficiency and CO2 Emissions: Aapplication of Energy Efficiency in Industry, Vienna,for Promoting Industrial Energy Efficiency in Developing

McKane, Aimee

2010-01-01T23:59:59.000Z

338

Office of Industrial Technologies: Industry partnerships  

SciTech Connect

US industries are making progress in turning the vision of the future into reality: More effective competition in global markets, increased industrial efficiency, more jobs, reduced waste generation and greenhouse gas emissions (to 1990 levels), improved environment. DOE`s Office of Industrial Technologies is catalyzing and supporting industry progress in many ways. This pamphlet gives an overview of OIT.

1995-04-01T23:59:59.000Z

339

California Industrial Energy Efficiency Potential  

E-Print Network (OSTI)

from 1% to 5% of base usage for natural gas. The achievableUsage A key initial step in the analysis was to develop a baseline understanding of industrial electricity and natural gas

Coito, Fred; Worrell, Ernst; Price, Lynn; Masanet, Eric; Rafael Friedmann; Rufo, Mike

2005-01-01T23:59:59.000Z

340

Industrial Uses of Vegetable Oils  

Science Conference Proceedings (OSTI)

Industrial Uses of Vegetable Oils offers new insights into these important (and growing) products of vegetable oils, while also covering developments in biodegradable grease, vegetable oils-based polyols, and the synthesis of surfactants from vegetable oil

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Industry Sponsored Research | Partnerships | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Partnering Mechanism Sample Sponsored Research Agreement SBIR-STTR Support Economic Development Industrial Partnerships University Partnerships Events and Conferences Success Stories Video Newsletters Staff Contacts Partnerships Home | Connect with ORNL | For Industry | Partnerships | Sponsored Research SHARE Sponsored Research Fiber Optic Research The Oak Ridge National Laboratory is a United States Department of Energy national laboratory, operated under contract by UT-Battelle, LLC. The laboratory's 1500+ research scientists and engineers conduct a vigorous program of scientific discovery and technology development, and ORNL is eager to engage industry in partnerships to help translate its research output into market impact and support for U.S. competitiveness. Companies wishing to learn about the research being

342

Quantifying potential industrial symbiosis : a case study of brick manufacturing  

E-Print Network (OSTI)

Humanity is currently on an unsustainable path of growth and development. One tool to address sustainability in industrial activities is Industrial Symbiosis, which is the study of cooperation across industry boundaries ...

Hodge, Matthew M

2007-01-01T23:59:59.000Z

343

Study of the health effects of chromium rollers used in cotton roller ginning industries and development of an alternative ginning process  

Science Conference Proceedings (OSTI)

This review paper realizes the hazards of chromium contamination and pollution caused by the use of Chrome Composite Leather-Clad (CCLC) rollers commonly used in cotton roller ginning industries and attempts to eliminate the chromium contamination and ... Keywords: chromium, cotton lint, ginning, rollers, rubber canvas

Gurumurthy Vijayan Iyer; Nikos E. Mastorakis

2006-06-01T23:59:59.000Z

344

Environmental impact studies of chrome rollers used by cotton roller ginning industries and design and development of pollution free chrome less RCF rollers  

Science Conference Proceedings (OSTI)

This paper discusses the pollution caused by Chrome Composite Leather-Clad (CCLC) rollers commonly used in cotton roller ginning industries and suggests an alternative roller material. The CCLC rollers contain about 18000 to 36000 mg/kg (ppm) total chromium ... Keywords: carcinogenic, chromium, cotton, eco-friendly, ginning, roller, rubberized roller

Gurumurthy Vijayan Iyer; Nikos E. Mastorakis

2006-08-01T23:59:59.000Z

345

Oklahoma Industrial Energy Management Program  

E-Print Network (OSTI)

In Oklahoma, industry consumes about 35% of the total energy consumed. While it is true that much work has been done in the larger companies, most small to medium sized companies have yet to undertake a substantial energy management program. Often they simply do not understand the savings possible or the techniques available. Recognizing this, a program was developed to acquaint Oklahoma industry with the potential savings allowable through energy management techniques. The program is entitled 'Oklahoma Industrial Energy; Management Program' and is located at Oklahoma State University. This paper describes past, on-going, and proposed activities of this Program and assesses their impact. Included are industrial energy management conferences, closed circuit television short courses on selected energy management topics, energy auditing, industrial energy audits (through the Oklahoma Energy Analysis and Diagnostic Center) , energy and water management research, and two courses currently being offered.

Turner, W. C.; Estes, C. B.

1982-01-01T23:59:59.000Z

346

EIA - 2010 International Energy Outlook - Industrial  

Gasoline and Diesel Fuel Update (EIA)

Industrial Industrial International Energy Outlook 2010 Industrial Sector Energy Consumption Worldwide industrial energy consumption increases by 42 percent, or an average of 1.3 percent per year, from 2007 to 2035 in the IEO2010 Reference case. Ninety-five percent of the growth occurs in non-OECD nations. Overview The world's industries make up a diverse sector that includes manufacturing, agriculture, mining, and construction. Industrial energy demand varies across regions and countries, depending on the level and mix of economic activity and technological development, among other factors. Energy is consumed in the industrial sector for a wide range of activities, such as processing and assembly, space conditioning, and lighting. Industrial energy use also includes natural gas and petroleum products used as feedstocks to produce non-energy products, such as plastics. In aggregate, the industrial sector uses more energy than any other end-use sector, consuming about one-half of the world's total delivered energy.

347

Strategies for an evolving generation industry  

SciTech Connect

This article deals with the changing structure of the power generation industry to include nonutility generation resources. The topics discussed include the permanence of nonutility generation as a power source, the evolving industry, and the strategies for an evolving industry. The emphasis is on developing sound, sophisticated purchasing procedures to fully benefit from this new generation resource.

Kee, E.

1990-09-27T23:59:59.000Z

348

Collaborative Research with NIST Scientists and Engineers  

Science Conference Proceedings (OSTI)

... work including: Building and Construction Industries; Steel Industry; Optoelectronics Industries; Computer Hardware and ...

2010-10-04T23:59:59.000Z

349

Guidelines for Estimating Unmetered Industrial Water Use  

SciTech Connect

The document provides a methodology to estimate unmetered industrial water use for evaporative cooling systems, steam generating boiler systems, batch process applications, and wash systems. For each category standard mathematical relationships are summarized and provided in a single resource to assist Federal agencies in developing an initial estimate of their industrial water use. The approach incorporates industry norms, general rules of thumb, and industry survey information to provide methodologies for each section.

Boyd, Brian K.

2010-08-01T23:59:59.000Z

350

Industrial Energy Procurement Contracts  

E-Print Network (OSTI)

Rates are going down and services are improving! Or are they? As opportunities to directly contract for energy expand from the larger industrials to include mid-market companies, existing energy supply and service contracts will be renegotiated and new ones developed. Many of these mid-level industrial customers typically lack in-house expertise on energy procurement, yet their operations use significant amounts of energy. This paper looks at some of the issues involved in the main terms of a procurement contract, as well as issues in contract formation and termination. Finally the paper reviews some of the recent energy aggregation and outsourcing deals to highlight some that worked and some that didn't.

Thompson, P.; Cooney, K.

2000-04-01T23:59:59.000Z

351

Materials Sustainability: Digital Resource Center - Industrial Ecology ...  

Science Conference Proceedings (OSTI)

Jul 2, 2008 ... Industrial Ecology offers an introduction to the topic commences with an exploration of the prerequisites for achieving sustainable development,...

352

Materials Sustainability: Digital Resource Center - Industrial Ecology ...  

Science Conference Proceedings (OSTI)

Jul 2, 2008 ... ROI is a not-for-profit entity dedicated to promoting industrial ecology, particularly in developing countries. This website contains a collection of...

353

Alten Industries Inc | Open Energy Information  

Open Energy Info (EERE)

Industries Inc Place Baltimore, Maryland Zip 21218 Product Maryland-based integrated alternative energy development corporation dedicated to supporting a viable domestic...

354

Borla Performance Industries, Inc. | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

cost and safety implications. This technology is also being integrated for use in refineries, industry gas and fuel cells systems and was developed using technology from the...

355

Longjitaihe Industry Group | Open Energy Information  

Open Energy Info (EERE)

Zip 7400 Sector Solar Product Chinese real estate developer foraying into solar PV projects. References Longjitaihe Industry Group1 LinkedIn Connections CrunchBase Profile No...

356

China National Machinery Industry Complete Engineering Corporation...  

Open Energy Info (EERE)

construction project, trading, military equipment manufacturing, real estate and waste-to-energy project development. References China National Machinery Industry Complete...

357

Rotem Industries Ltd | Open Energy Information  

Open Energy Info (EERE)

research, development, construction & consultation of major solar energy projects: solar power plants and solar powered desalination study. References Rotem Industries Ltd1...

358

ESCO Industry in China  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ESCO Development in ESCO Development in China China-America EE Forum 2011.5.6, S.F Contents Fast development 1 Great potential 2 Opportunities & Challenges 3 Function of EMCA 4 China Energy Conservation project  Officially started in 1998;  It is a key international cooperation project in the field of energy conservation by Chinese government and World Bank/GEF;  The main purpose of the project is to promote Energy Performance Contracting (EPC) mechanism and develop ESCO industry in China Project progress-1 st phase 3 pilot ESCOs: Beijing Liaoning Shandong Phase I EC information Dissemination Center(ECIDC) Project progress-2 nd phase EMCA Phase II I& G New and Potential ESCOs Technical support Financial support Project Progress- 2 nd Phase EMCA---provide practical technical

359

Opto-electronic device for frequency standard generation and terahertz-range optical demodulation based on quantum interference  

DOE Patents (OSTI)

An opto-electronic system and technique for comparing laser frequencies with large frequency separations, establishing new frequency standards, and achieving phase-sensitive detection at ultra high frequencies are disclosed. Light responsive materials with multiple energy levels suitable for multi-photon excitation are preferably used for nonlinear mixing via quantum interference of different excitation paths affecting a common energy level. Demodulation of a carrier with a demodulation frequency up to 100`s THZ can be achieved for frequency comparison and phase-sensitive detection. A large number of materials can be used to cover a wide spectral range including the ultra violet, visible and near infrared regions. In particular, absolute frequency measurement in a spectrum from 1.25 {micro}m to 1.66 {micro}m for fiber optics can be accomplished with a nearly continuous frequency coverage. 7 figs.

Georgiades, N.P.; Polzik, E.S.; Kimble, H.J.

1999-02-02T23:59:59.000Z

360

Opto-electronic device for frequency standard generation and terahertz-range optical demodulation based on quantum interference  

DOE Patents (OSTI)

An opto-electronic system and technique for comparing laser frequencies with large frequency separations, establishing new frequency standards, and achieving phase-sensitive detection at ultra high frequencies. Light responsive materials with multiple energy levels suitable for multi-photon excitation are preferably used for nonlinear mixing via quantum interference of different excitation paths affecting a common energy level. Demodulation of a carrier with a demodulation frequency up to 100's THZ can be achieved for frequency comparison and phase-sensitive detection. A large number of materials can be used to cover a wide spectral range including the ultra violet, visible and near infrared regions. In particular, absolute frequency measurement in a spectrum from 1.25 .mu.m to 1.66 .mu.m for fiber optics can be accomplished with a nearly continuous frequency coverage.

Georgiades, Nikos P. (Pasadena, CA); Polzik, Eugene S. (H.o slashed.jbjerg, DK); Kimble, H. Jeff (LaCanada, CA)

1999-02-02T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Improving the efficiency of the later stages of the drug development process : survey results from the industry, academia, and the FDA  

E-Print Network (OSTI)

Drug development in the United States is a lengthy and expensive endeavor. It is estimated that average development times range from eleven to fifteen years and exceed costs of one billion dollars. The development pathway ...

Gottschalk, Adrian Hedley Benjamin, 1975-

2004-01-01T23:59:59.000Z

362

NSLS Industrial User Program  

NLE Websites -- All DOE Office Websites (Extended Search)

| Industrial Program Coordinator | Publications Courtesy of The New York Times, Noah Berger The overall goal of the plan to enhance the NSLS facility's Industrial Users'...

363

Uranium industry annual 1997  

SciTech Connect

This report provides statistical data on the U.S. uranium industry`s activities relating to uranium raw materials and uranium marketing.

NONE

1998-04-01T23:59:59.000Z

364

Construction Industry Institute  

Science Conference Proceedings (OSTI)

... in one of our country's most vital industries. ... An industry-led program to disseminate practical ... fire-proofing materials, connections, and steel trusses; ...

2010-10-05T23:59:59.000Z

365

Clean Technology Sustainable Industries Organization | Open Energy  

Open Energy Info (EERE)

Sustainable Industries Organization Sustainable Industries Organization Jump to: navigation, search Name Clean Technology & Sustainable Industries Organization Place Royal Oak, Michigan Zip 48073 Product A non-profit membership industry organization formed to advance the global development and deployment of clean and sustainable technologies References Clean Technology & Sustainable Industries Organization[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Clean Technology & Sustainable Industries Organization is a company located in Royal Oak, Michigan . References ↑ "Clean Technology & Sustainable Industries Organization" Retrieved from "http://en.openei.org/w/index.php?title=Clean_Technology_Sustainable_Industries_Organization&oldid=343669"

366

Industrial Applications of Renewable Resources  

Science Conference Proceedings (OSTI)

Archive of Industrial Applications of Renewable Resources Industrial Applications of Renewable Resources Cincinnati, Ohio, USA Industrial Applications of Renewable Resources ...

367

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 51 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Industrial Demand Module The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 15 manufacturing and 6 non-manufacturing industries. The manufacturing industries are further subdivided into the energy- intensive manufacturing industries and nonenergy-intensive manufacturing industries (Table 6.1). The manufacturing industries are modeled through the use of a detailed process-flow or end-use accounting procedure, whereas the non- manufacturing industries are modeled with substantially less detail. The petroleum refining industry is not included in the Industrial Module, as it is simulated separately in the Petroleum Market Module of NEMS. The Industrial Module calculates

368

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 Industrial Demand Module The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 15 manufacturing and 6 non-manufacturing industries. The manufacturing industries are further subdivided into the energy- intensive manufacturing industries and non-energy-intensive manufacturing industries (Table 6.1). The manufacturing industries are modeled through the use of a detailed process-flow or end-use accounting procedure, whereas the non- manufacturing industries are modeled with substantially less detail. The petroleum refining industry is not included in the Industrial Demand Module, as it is simulated separately in the Petroleum Market Module of NEMS. The Industrial Demand Module calculates energy consumption for the four Census Regions (see Figure 5) and disaggregates the energy consumption

369

Industrial - Utility Cogeneration Systems  

E-Print Network (OSTI)

Cogeneration may be described as an efficient method for the production of electric power in conjunction with process steam or heat which optimizes the energy supplied as fuel to maximize the energy produced for consumption. In a conventional electric utility power plant, considerable energy is wasted in the form of heat rejection to the atmosphere thru cooling towers, ponds or lakes, or to rivers. In a cogeneration system heat rejection can be minimized by systems which apply the otherwise wasted energy to process systems requiring energy in the form of steam or heat. Texas has a base load of some 75 million pounds per hour of process steam usage, of which a considerable portion could be generated through cogeneration methods. The objective of this paper is to describe the various aspects of cogeneration in a manner which will illustrate the energy saving potential available utilizing proven technology. This paper illustrates the technical and economical benefits of cogeneration in addition to demonstrating the fuel savings per unit of energy required. Specific examples show the feasibility and desirability of cogeneration systems for utility and industrial cases. Consideration of utility-industrial systems as well as industrial-industrial systems will be described in technical arrangement as well as including a discussion of financial approaches and ownership arrangements available to the parties involved. There is a considerable impetus developing for the utilization of coal as the energy source for the production of steam and electricity. In many cases, because of economics and site problems, the central cogeneration facility will be the best alternative for many users.

Harkins, H. L.

1979-01-01T23:59:59.000Z

370

The changing battery industry  

SciTech Connect

This report provides an economic and technological assessment of the electrical battery industry, highlighting major trends. Among those systems considered are lithium-based, sodium-sulfur nickel-zinc, nickel-iron, nickel-hydrogen, zinc-chloride, conductive polymer, and redox cells. Lead-acid, nickel-cadmium, and manganese dioxide-based batteries and direct solar power and fuel cells are discussed in relation to these new techniques. New applications, including electric vehicles, solar power storage, utility load leveling, portable appliances, computer power and memory backup, and medical implants are discussed. Predictions and development scenarios for the next twenty years are provided for the U.S. market.

Not Available

1987-01-01T23:59:59.000Z

371

Office of Industrial Technologies research in progress  

DOE Green Energy (OSTI)

The US Department of Energy (DOE) Office of Industrial Technologies (OIT) conducts research and development activities which focus on improving energy efficiency and providing for fuel flexibility within US industry in the area of industrial conservation. The mission of OIT is to increase the utilization of existing energy-efficient equipment and to find and promote new, cost-effective ways for industrial facilities to improve their energy efficiency and minimize waste products. To ensure advancement of the technological leadership of the United States and to improve the competitiveness of American industrial products in world markets, OIT works closely with industrial partners, the staffs of the national laboratories, and universities to identify research and development needs and to solve technological challenges. This report contains summaries of the currently active projects supported by the Office of Industrial Technologies.

Not Available

1993-05-01T23:59:59.000Z

372

Tom Rogers Director, Industrial Partnerships  

NLE Websites -- All DOE Office Websites (Extended Search)

Tom Rogers, rogerstc@ornl.gov 865-241-2149 Tom Rogers, rogerstc@ornl.gov 865-241-2149 Tom Rogers Director, Industrial Partnerships and Economic Development Tom Rogers was named Director of Industrial Partnerships and Economic Development at the Oak Ridge National Laboratory in June, 2008. His responsibilities include directing engagements with industrial partners, forging new ORNL entrepreneurial support efforts, and leading a number of strategic initiatives such as the Carbon Fiber Composites Cluster and development of the Oak Ridge Science and Technology Park. Prior to joining ORNL, Tom was the founding President and CEO of Technology 2020, a national award-winning public-private partnership focused on a building a robust regional entrepreneurial support system. Tom has also served as the Executive Director of the Tennessee Technology

373

FAQS Job Task Analyses - Industrial Hygiene  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Industrial Hygiene FAQS Industrial Hygiene FAQS STEP 1: Job Task Analysis for Tasks Task (and Number) Source Importance Frequency (1) Plan, observe, and evaluate contractor performance involving industrial hygiene activities to ensure the adequacy and effectiveness of contractor programs such as: * Technical performance (e.g., adequacy of technical practices) * Plans, policies, and procedures * Management controls * Worker training and qualification programs * Occurrence reporting and corrective actions * Occupational health programs FAQS Duties and Responsibilities Paragraph C 4 5 (2) Develop, review, and assess industrial hygiene documentation. FAQS Duties and Responsibilities Paragraph D 4 5 (3) Resolve or facilitate the resolution of industrial hygiene issues.

374

Climate VISION: Industry Associations  

Office of Scientific and Technical Information (OSTI)

Industry Associations Industry Associations Aluminum Aluminum Association (Coordinating aluminum industry Climate VISION activities) The Aluminum Association, Inc. is the trade association for producers of primary aluminum, recyclers and semi-fabricated aluminum products, as well as suppliers to the industry. The Association provides leadership to the industry through its programs and services which aim to enhance aluminum's position in a world of proliferating materials, increase its use as the "material of choice," remove impediments to its fullest use, and assist in achieving the industry's environmental, societal, and economic objectives. Automobile Manufacturers Alliance of Automobile Manufacturers (Coordinating automobile industry Climate VISION activities) The Alliance of Automobile Manufacturers, Inc. is a trade association

375

Web-Based Industrial Energy Management Tool  

Science Conference Proceedings (OSTI)

This report describes continuing research on the Industrial Energy Management Tool (IEMT), a web-based software resource intended for the evaluation of industrial energy efficiency measures. The IEMT software development is ongoing, and this report covers the status of an alpha tool that has already been created and plans for moving forward with development of a beta product.

2008-03-31T23:59:59.000Z

376

China and India Industrial Efficiency NREL Partnership | Open Energy  

Open Energy Info (EERE)

China and India Industrial Efficiency NREL Partnership China and India Industrial Efficiency NREL Partnership Jump to: navigation, search Logo: China-NREL Industrial Efficiency Partnership Name China-NREL Industrial Efficiency Partnership Agency/Company /Organization National Renewable Energy Laboratory Sector Energy Focus Area Energy Efficiency, Industry Topics Background analysis Country China Eastern Asia References NREL International Program Overview Abstract In support of the DOE Office of Energy Efficiency and Renewable Energy (EERE) Industrial Technologies Program's (ITP) activities to promote industrial energy efficiency internationally, the NREL industrial communications team is developing a specialized portfolio of technical and outreach materials. "In support of the DOE Office of Energy Efficiency and Renewable Energy

377

Innovative New Industrial Technologies: An Industry/DOE Joint Endeavor  

E-Print Network (OSTI)

The Department of Energys Office of Industrial Programs supports research and development leading to improved energy efficiency and greater overall productivity in the industrial sector. Its basic strategy is a program of cost-shared R&D, incorporating projects with such risk that the private sector will not pursue them independently. This paper describes the Offices major activities, operating premises and research areas. Policy considerations affecting the programs content are identified and criteria applied in project selection are discussed. Achievement of constructive industry involvement in program development and review is viewed as vital to success. This goal, and the means by which it is being pursued, are emphasized.

Gross, T. J.

1986-06-01T23:59:59.000Z

378

A Novel Lightweight Low-Power Dual-Beam Ozone Photometer Utilizing Solid-State Optoelectronics  

Science Conference Proceedings (OSTI)

Recent advances in semiconductor materials and fabrication techniques have allowed the development of light-emitting diodes (LEDs) with wavelengths extending down into the UV-C region (? < 280 nm). A new ozone photometer has been developed ...

Lars E. Kalnajs; Linnea M. Avallone

2010-05-01T23:59:59.000Z

379

Deregulation-restructuring: Evidence for individual industries  

SciTech Connect

Several studies have measured the effects of regulation on a particular industry. These studies range widely in sophistication, from simple observation (comparison) of pre-transformation and post-transformation actual industry performance to econometric analysis that attempt to separate the effects of deregulation from other factors in explaining changes in an industry`s performance. The major problem with observation studies is that they are unable to measure the effect of one particular event, such as deregulation, on an industry`s performance. For example, at the same time that the United Kingdom privatized its electric power industry, it also radically restructured the industry to encourage competition and instituted a price-cap mechanism to regulate the prices of transmission, distribution, and bundled retail services. Subsequent to these changes in 1991, real prices for most UK electricity customers have fallen. It is not certain however, which of these factors was most important or even contributed to the decline in price. In any event, one must be cautious in interpreting the results of studies that attempt to measure the effect of deregulation per se for a specific industry. This report highlights major outcomes for five industries undergoing deregulation or major regulatory and restructuring reforms. These include the natural gas, transportation, UK electric power, financial, and telecommunications industries. Particular attention was given to the historical development of events in the telecommunications industry.

Costello, K.W.; Graniere, R.J.

1997-05-01T23:59:59.000Z

380

Cost Calculating of Optoelectronics - An Analysis of Cost Items for a Camera Application used in the Automotive Industry at Volvo Cars Corporation.  

E-Print Network (OSTI)

??The purpose of the thesis was to define the manufacturing process of a camera application with included optics and its integration with electronics and verify (more)

Vekariya, Nimisha

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

The future steelmaking industry and its technologies  

SciTech Connect

The objective of this report is to develop a vision of the future steelmaking industry including its general characteristics and technologies. In addition, the technical obstacles and research and development opportunities for commercialization of these technologies are identified. The report is being prepared by the Sloan Steel Industry Competitiveness Study with extensive input from the industry. Industry input has been through AISI (American Iron and Steel Institute), SMA (Steel Manufacturers Association) and contacts with individual company executives and technical leaders. The report identifies the major industry drivers which will influence technological developments in the industry for the next 5--25 years. Initially, the role of past drivers in shaping the current industry was examined to help understand the future developments. Whereas this report concentrates on future technologies other major factors such as national and international competition, human resource management and capital concerns are examined to determine their influence on the future industry. The future industry vision does not specify specific technologies but rather their general characteristics. Finally, the technical obstacles and the corresponding research and development required for commercialization are detailed.

Fruehan, R.J.; Paxton, H.W.; Giarratani, F.; Lave, L. [Carnegie-Mellon Univ., Pittsburgh, PA (United States)]|[Pittsburgh Univ., PA (United States)

1995-01-01T23:59:59.000Z

382

Development of Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Iron and Steel Sector  

E-Print Network (OSTI)

presented energy cost curves for energy efficiency measuressection then develops energy efficiency cost curves for thepresented energy cost curves for energy efficiency measures

Xu, T.T.

2011-01-01T23:59:59.000Z

383

Memorandum of Understanding between the Department of Energy of the United States of America and the National Development and Reform Commission of the People's Republic of China Concerning Industrial Energy Efficiency Cooperation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

THE DEPARTMENT OF ENERGY OF THE UNITED STATES OF AMERICA AND THE NATIONAL DEVELOPMENT AND REFORM COMMISSION OF THE PEOPLE'S REPUBLIC OF CHINA CONCERNING INDUSTRIAL ENERGY EFFICIENCY COOPERATION The Department of Energy of the United States of America (DOE) and the National Development and Reform Commission of the People's Republic of China (NDRC), jointly referred to herein as the "Participants"; RECOGNIZING that the development and use of energy are key elements of the economic growth of the United States and the People's Republic of China (PRC); SHARING common serious energy challenges from increasing energy imports and worsening environmental impacts as energy use rises; SHARING the sense of commitment to enhancing energy security through cooperation;

384

Emerging trends in the satellite industry  

E-Print Network (OSTI)

Risk aversion in the satellite industry has fostered long development cycles and low rates of innovation in the past. Emerging trends in propulsion technology development and spacecraft architecture design could lead to ...

Salazar, Vagn Knudsen

2012-01-01T23:59:59.000Z

385

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 12 manufacturing and 6 nonmanufacturing industries. The manufacturing industries are further subdivided into the energy-intensive manufacturing industries and nonenergy-intensive manufacturing industries. The manufacturing industries are modeled through the use of a detailed process flow or end use accounting procedure, whereas the nonmanufacturing industries are modeled with substantially less detail (Table 17). The Industrial Demand Module forecasts energy consumption at the four Census region level (see Figure 5); energy consumption at the Census Division level is estimated by allocating the Census region forecast using the SEDS 27 data.

386

Industrial Decision Making  

E-Print Network (OSTI)

Domestic industrial investment has declined due to unfavorable energy prices, and external markets. Investment behavior has changed over the past few years, and will continue due to high labor costs, tight markets and an unstable U.S. economy although, freight costs, favorable exchange rates and high capacity utilization will encourage future industrial investment. Industry will eventually enter a new period of major investment. Future industrial investment will be an opportunity to influence the energy efficiency of these facilities for generations to come. Program managers must begin engaging industrial customers now, in order to exploit this unprecedented opportunity to change future energy use patterns. This paper reviews recent market trends and industrial investment decision-making. The paper will also address several important questions: Why has industrial investment declined? What is the outlook for industrial investment? How can programs engage industry for future opportunities?

Elliott, R. N.; McKinney, V.; Shipley, A.

2008-01-01T23:59:59.000Z

387

Introduction of New Technologies to Competing Industrial Customers  

Science Conference Proceedings (OSTI)

Motivated by several examples from industry, such as the introduction of a biotechnology-based process innovation in nylon manufacturing, we consider a technology provider that develops and introduces innovations to a market of industrial customers---original ... Keywords: business-to-business, game theory, industrial customers, industrial markets, multistage game, technology adoption, technology introduction

Sanjiv Erat; Stylianos Kavadias

2006-11-01T23:59:59.000Z

388

Industry sector analysis - energy industry news (Hungary) 1994. Export trade information  

Science Conference Proceedings (OSTI)

The article is derived from a telegraphic report dated 1 February 1994, prepared at the American Embassy-Budapest. It discusses recent developments from the Hungarian energy industry.

Not Available

1994-02-01T23:59:59.000Z

389

Industry sector analysis - energy industry news (Hungary) 1994. Export trade information  

Science Conference Proceedings (OSTI)

The article is derived from a telegraphic report dated 18 April 1994, prepared at the American Embassy-Budapest. It discusses recent developments from the Hungarian energy industry.

Not Available

1994-04-18T23:59:59.000Z

390

Industrial Use of Infrared Inspections  

E-Print Network (OSTI)

Infrared is and has been an established technology in the military and aerospace fields. However, only relatively recently has this technology found a "use" in the industrial sector. Many reasons exist why the technology has not been used, but in the final analysis it comes down to the fact that the industrial management responsible for the operations and production budgets did not, and in many cases, still does not understand the economic benefits to the company that infrared industrial inspections can bring about. Over the last 2-3 years a number of articles have appeared in various industrial publications concerning infrared surveys. However, all of the articles have dealt with the technical aspects of infrared inspections, with the economics either completely neglected or mentioned only in passing. I believe that in the real industrial world it is the economic benefits of a technology that allow the product of that technology to reach the market and become a success, and not the fact that a technology is useful per se. In this presentation, I shall be focusing primarily on the major economic aspects of the surveys and what the end results really represent in terms of economic benefits. Once the economic benefits of these inspections are clearly understood, it will be readily apparent why the industrial use of these inspections is developing rapidly.

Duch, A. A.

1979-01-01T23:59:59.000Z

391

Industrial Buildings Tools and Resources  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Rolf Butters Rolf Butters Industrial Technologies Program Industrial Buildings Tools and Resources Webinar - June 11, 2009 Michael MacDonald Agenda  Introduction to Industrial Buildings Opportunity and Tools  EERE Funding, Opportunities, and Resources  Next Steps 6/11/2009 2 Facilities Energy  ITP has been working for a couple years now to develop tools to address facilities energy use, present in most plants, and about 8% of total sector energy use  First tool is a Score Card, implemented both as a stand- alone Excel file and for QuickPEP - Score Card has to be simple, so is approximate - But it can be a very important tool for scoping facilities energy use at a plant  Second tool is an adaptation of the BCHP Screening Tool, originally developed by the Distributed Energy program but

392

Industrial User Office | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Industrial Liaison Office Industrial Liaison Office Industrial Liaison Office registration page New to Synchrotron Radiation New to the APS Already a User Advanced Photon Source Industrial Liaison Office Welcome to the Advanced Photon Source (APS) Industrial Liaison Office home page. The purpose of this Office is to provide outreach from the APS to the industrial community. As we develop the Office and this website to better address the needs of industrial users of the APS, both current and prospective, we are soliciting input by requesting projects and measurements that you would like to perform at the APS. Please complete the form below so that we can begin communicating with you. Questions? Email aps-i@aps.anl.gov. General Information Company Name *required First Name *required Last Name *required

393

Oklahoma Industrial Energy Management Program  

E-Print Network (OSTI)

The need for sound energy management is no longer worthy of debate. Action is necessary and much is being done by U.S. industry. Unfortunately, however, the majority of the work is being done by the few large energy intensive industries throughout the country. The average small to medium sized company has yet to undertake a dedicated program. The reasons are numerous, but often it is simply because of a lack of knowledge of techniques or the amount of savings possible. Recognizing this, the Oklahoma Department of Energy designed a program to acquaint Oklahoma industry with the potential savings available through energy management and some basic techniques. The program is entitled "Oklahoma Industrial Energy Management Program" and is housed at Oklahoma State University. The program is funded by the U. S. Department of Energy through the State Energy Conservation Plan. This paper describes the program offerings, impact to date and plans for the future. The program offerings basically include: 1. A series of tuition free Industrial Energy Management Conferences (over 20 given to date involving many Oklahoma industries). 2. A free energy newsletter entitled "Energy Channel" mailed to all participating Oklahoma industries. 3. A series of Energy Audit booklets including instructions and forms. 4. Technical aid on a limited basis. 5. A series of laboratory type experiments involving power factor, solar energy, boiler combustion improvement and other energy related projects. 6. Fact sheet publication as the need develops. Plans for the future include expansion of the program to small businesses in general through the Energy Extension Service and more technical aid to participating industries, The basic plan involving the services above shall remain intact. The program has been very successful to date. The results are directly transferable to other states and the program directors are willing to share information.

Turner, W. C.; Webb, R. E.; Phillips, J. M.; Viljoen, T. A.

1979-01-01T23:59:59.000Z

394

The implementation of the triple helix model of industry-university-government relations in Puerto Rico to promote knowledge-based regional economic development  

E-Print Network (OSTI)

Puerto Rico, an island in the Caribbean, has long sought to develop a high-tech economy and has struggled in the process. Two initiatives, Puerto Rico TechnoEconomic Corridor (PRTEC) and the Eastern Central Technological ...

Ramos-Malts, Ana Lorena

2010-01-01T23:59:59.000Z

395

International industrial sector energy efficiency policies  

SciTech Connect

Over 40 percent of the energy consumed globally is used in the industrial sector. In China, this sector consumes an even larger proportion, reaching nearly 70 percent in 1997. A variety of energy efficiency policies and programs have been instituted in both industrialized and developing countries in an effort to improve the energy efficiency of the industrial sector. There are very few comprehensive evaluations of these industrial sector energy efficiency policies; however a number of recent workshops and conferences have included a focus on these policies. Three important meetings were the International Energy Agency's Industrial Energy Efficiency: Policies and Programs Conference in 1994, Industrial Energy Efficiency Policies: Understanding Success and Failure - A Workshop Organized by the International Network for Energy Demand Analysis in the Industrial Sector in 1998, and the American Council for an Energy-Efficient Economy's 1999 Summer Study on Energy Efficiency in Industry. Man y articles from these meetings are included as attachments to this memo. This paper provides a brief description of each of seven categories of individual industrial energy efficiency policies and programs, discuss which industrial sectors or types of equipment they apply to, and provide references for articles and reports that discuss each policy or program in more detail. We begin with mandatory-type policies and move to more voluntary-type policies. We then provide a brief description of four integrated industrial energy efficiency policies and provide references for articles and reports that describe these policies in greater detail.

Price, Lynn; Worrell, Ernst

2000-01-01T23:59:59.000Z

396

International industrial sector energy efficiency policies  

SciTech Connect

Over 40 percent of the energy consumed globally is used in the industrial sector. In China, this sector consumes an even larger proportion, reaching nearly 70 percent in 1997. A variety of energy efficiency policies and programs have been instituted in both industrialized and developing countries in an effort to improve the energy efficiency of the industrial sector. There are very few comprehensive evaluations of these industrial sector energy efficiency policies; however a number of recent workshops and conferences have included a focus on these policies. Three important meetings were the International Energy Agency's Industrial Energy Efficiency: Policies and Programs Conference in 1994, Industrial Energy Efficiency Policies: Understanding Success and Failure - A Workshop Organized by the International Network for Energy Demand Analysis in the Industrial Sector in 1998, and the American Council for an Energy-Efficient Economy's 1999 Summer Study on Energy Efficiency in Industry. Man y articles from these meetings are included as attachments to this memo. This paper provides a brief description of each of seven categories of individual industrial energy efficiency policies and programs, discuss which industrial sectors or types of equipment they apply to, and provide references for articles and reports that discuss each policy or program in more detail. We begin with mandatory-type policies and move to more voluntary-type policies. We then provide a brief description of four integrated industrial energy efficiency policies and provide references for articles and reports that describe these policies in greater detail.

Price, Lynn; Worrell, Ernst

2000-01-01T23:59:59.000Z

397

Industrial ecology Prosperity Game{trademark}  

SciTech Connect

Industrial ecology (IE) is an emerging scientific field that views industrial activities and the environment as an interactive whole. The IE approach simultaneously optimizes activities with respect to cost, performance, and environmental impact. Industrial Ecology provides a dynamic systems-based framework that enables management of human activity on a sustainable basis by: minimizing energy and materials usage; insuring acceptable quality of life for people; minimizing the ecological impact of human activity to levels that natural systems can sustain; and maintaining the economic viability of systems for industry, trade and commerce. Industrial ecology applies systems science to industrial systems, defining the system boundary to incorporate the natural world. Its overall goal is to optimize industrial activities within the constraints imposed by ecological viability, globally and locally. In this context, Industrial systems applies not just to private sector manufacturing and services but also to government operations, including provision of infrastructure. Sandia conducted its seventeenth Prosperity Game{trademark} on May 23--25, 1997, at the Hyatt Dulles Hotel in Herndon, Virginia. The primary sponsors of the event were Sandia National Laboratories and Los Alamos National Laboratory, who were interested in using the format of a Prosperity Game to address some of the issues surrounding Industrial Ecology. Honorary game sponsors were: The National Science Foundation; the Committee on Environmental Improvement, American Chemical Society; the Industrial and Engineering Chemistry Division, American Chemical Society; the US EPA--The Smart Growth Network, Office of Policy Development; and the US DOE-Center of Excellence for Sustainable Development.

Beck, D.; Boyack, K.; Berman, M.

1998-03-01T23:59:59.000Z

398

Industrial | Open Energy Information  

Open Energy Info (EERE)

to: navigation, search Click to return to AEO2011 page AEO2011 Data From AEO2011 report . Market Trends Despite a 54-percent increase in industrial shipments, industrial energy...

399

The Copper Industry  

Science Conference Proceedings (OSTI)

...These products are sold to a wide variety of industrial users. Certain mill products??chiefly wire, cable, and most

400

NIST Industry Day 2012  

Science Conference Proceedings (OSTI)

... at www.fedbizopps.gov. Search NIST-AMD-INDUSTRY-DAY-2012 in the Quick Search engine. Deadline for registration ...

2013-08-30T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

America's Booming Wind Industry  

Energy.gov (U.S. Department of Energy (DOE))

Sharing key findings from two new Energy Department reports that highlight the record growth of America's wind industry.

402

Fabrication and characterization of quantum-confined optoelectronic devices based on CdSe nanocrystals  

E-Print Network (OSTI)

Colloidal semiconductor quantum dots (QDs), or nanocrystals (NCs), are the subject of intense research for their novel size dependent optical and electronic properties. Since the development of synthetic methods to produce ...

Woo, Wing-Keung, 1972-

2002-01-01T23:59:59.000Z

403

Instructional design authoring support for the development of serious games and mixed reality training. Paper presented at Interservice/Industry Training, Simulation and Education Conference  

E-Print Network (OSTI)

A significant trend is underway to apply entertainment game technologies to training environments, the Serious Games movement. These training games will be delivered through traditional technologies such as desktop computers as well as mobile computers, embedded in operational equipment and mixed reality technologies. The design and development of effective training using these technologies is challenging. There is often deep conflict between ensuring that the desired instructional goals are met while at the same time staying true to key benefits of games for trainingengagement, fun, and complexity of the training scenario. The unpredictability of games impedes control of training variables and poorly designed games may result in negative training effects. Yet, trainers realize that many current training systems and instructional methods are ineffective, lack real world complexity and are boring. There is a need to bridge the gap between proven simulation and other training systems, and gaming entertainment technologies. Authoring tools are needed to ensure these new systems are used effectively. Our team has been investigating how to develop an instructional design authoring tool that supports the entire process from identifying training requirements through the delivery of regular and embedded training. We developed the Simulation-game Instructional Systems Design (SG-ISD) Model which has been mapped to ensure it supports official Instructional Systems Development (ISD) processes for effective design while integrating game

Sonny E. Kirkley, Ph.D.; Steve Tomblin; Jamie Kirkley

2005-01-01T23:59:59.000Z

404

NICE3: Industrial Refrigeration System  

SciTech Connect

Energy Concepts has developed an absorption-augmented system as a cost-effective means of achieving more cooling capacity with a substantial reduction in energy consumption and greenhouse gas emissions for industrial refrigeration. It cuts fuel consumption by 30% by combining an internal combustion engine with a mechanical compression refrigeration system and an absorption refrigeration system. The absorption system is powered by engine waste heat. Conventional industrial refrigeration uses mechanical vapor compression, powered by electric motors, which results in higher energy costs. By the year 2010, the new system could cut fuel consumption by 19 trillion Btu and greenhouse emissions by more than 1 million tons per year.

Simon, P.

1999-09-29T23:59:59.000Z

405

Transforming the Oil Industry into the Energy Industry  

E-Print Network (OSTI)

innovation and lets industry pick winning technologies. TheTransforming the Oil Industry intothe Energy Industry BY DANIEL SPERLING AND SONIA YEH A C C E

Sperling, Daniel; Yeh, Sonia

2009-01-01T23:59:59.000Z

406

From Industry Protection to Industry Promotion: IT Policy in Brazil  

E-Print Network (OSTI)

Brazilian banking automation industry. Science, TechnologyBrazilian liberalisation of the IT industry on technologicalWorking paper. Computer Industry Almanac, Inc. (1999).

Botelho, Antonio Jose Junqueira; Dedrick, Jason; Kraemer, Kenneth L.; Tigre, Paulo Bastos

1999-01-01T23:59:59.000Z

407

Industrial Carbon Capture Project Selections  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

(Partner Organizations) Funding Lead Organization Location (City, State) Project Title - Project Description 1) Large Scale Testing of Advanced Gasification Technologies Air Products & Chemicals, Inc. $71,700,000 Allentown, PA Development of ITM Oxygen Technology for Integration with Advanced Industrial Systems Air Products will accelerate commercial manufacture of ion transport membranes modules and initiate the development a 2,000 TPD pre- commercial scale facility ahead of schedule, enabling this technology

408

Industry - ORNL Neutron Sciences  

NLE Websites -- All DOE Office Websites (Extended Search)

Industry banner Industry banner Neutron scattering research has applications in practically every field, and neutron research at ORNL is leading to productive partnerships with the industrial and business communities. We welcome proposals for all types of research, including those involving proprietary work. Recent studies have led to discoveries with potential applications in fields such as medicine, energy, and various metals technologies. For more information, please see our recent research highlights. Research Collaborations Industry-Driven Research Benefits Plastics Manufacturing Corning uses VULCAN to test limits of ceramic material for car emission controls, filtration devices Neutrons Probe Inner Workings of Batteries Industry and Neutron Science: Working To Make a Match

409

Jax Industries | Open Energy Information  

Open Energy Info (EERE)

Jax Industries Jax Industries Jump to: navigation, search Name Jax Industries Place Hillsboro, Oregon Product Developer of recharge systems for CZ process silicon ingot growers, some of which produce PV silicon feedstock. Coordinates 43.651735°, -90.341144° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":43.651735,"lon":-90.341144,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

410

Uranium industry annual 1998  

SciTech Connect

The Uranium Industry Annual 1998 (UIA 1998) provides current statistical data on the US uranium industry`s activities relating to uranium raw materials and uranium marketing. It contains data for the period 1989 through 2008 as collected on the Form EIA-858, ``Uranium Industry Annual Survey.`` Data provides a comprehensive statistical characterization of the industry`s activities for the survey year and also include some information about industry`s plans and commitments for the near-term future. Data on uranium raw materials activities for 1989 through 1998, including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment, are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2008, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, and uranium inventories, are shown in Chapter 2. The methodology used in the 1998 survey, including data edit and analysis, is described in Appendix A. The methodologies for estimation of resources and reserves are described in Appendix B. A list of respondents to the ``Uranium Industry Annual Survey`` is provided in Appendix C. The Form EIA-858 ``Uranium Industry Annual Survey`` is shown in Appendix D. For the readers convenience, metric versions of selected tables from Chapters 1 and 2 are presented in Appendix E along with the standard conversion factors used. A glossary of technical terms is at the end of the report. 24 figs., 56 tabs.

NONE

1999-04-22T23:59:59.000Z

411

Uranium industry annual 1994  

SciTech Connect

The Uranium Industry Annual 1994 (UIA 1994) provides current statistical data on the US uranium industry`s activities relating to uranium raw materials and uranium marketing during that survey year. The UIA 1994 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. It contains data for the 10-year period 1985 through 1994 as collected on the Form EIA-858, ``Uranium Industry Annual Survey.`` Data collected on the ``Uranium Industry Annual Survey`` (UIAS) provide a comprehensive statistical characterization of the industry`s activities for the survey year and also include some information about industry`s plans and commitments for the near-term future. Where aggregate data are presented in the UIA 1994, care has been taken to protect the confidentiality of company-specific information while still conveying accurate and complete statistical data. A feature article, ``Comparison of Uranium Mill Tailings Reclamation in the United States and Canada,`` is included in the UIA 1994. Data on uranium raw materials activities including exploration activities and expenditures, EIA-estimated resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities, including purchases of uranium and enrichment services, and uranium inventories, enrichment feed deliveries (actual and projected), and unfilled market requirements are shown in Chapter 2.

NONE

1995-07-05T23:59:59.000Z

412

Tax-Exempt Industrial Revenue Bonds (Kansas) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Industrial Revenue Bonds (Kansas) Industrial Revenue Bonds (Kansas) Tax-Exempt Industrial Revenue Bonds (Kansas) < Back Eligibility Agricultural Commercial Construction Industrial Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Kansas Program Type Bond Program Provider Revenue Tax-Exempt Industrial Revenue Bonds are issued by cities and counties for the purchase, construction, improvement or remodeling of a facility for agricultural, commercial, hospital, industrial, natural resources, recreational development or manufacturing purposes. The board of county commissioners of any county or the governing body of any city may approve an exemption of property funded by industrial revenue bonds (IRB's). Some

413

Implementation of solar industrial process heat: summary  

SciTech Connect

The implementation of solar industrial process heat systems will depend not only on the successful development of reliable and efficient solar technologies, but also on the intelligent and sound application of process engineering principles. This poses an important challenge which must be given increasing attention if SIPH systems are to be adopted by industry. (MOW)

Kearney, D. W.

1979-11-01T23:59:59.000Z

414

Photovoltaic industry progress through 1984  

DOE Green Energy (OSTI)

The growth of the US photovoltaics (PV) industry over the past decade has been impressive. First designed to provide power for satellites using high-cost production techniques, PV is now the economical choice in many remote terrestrial applications. The remarkable growth of PV in terms of quality of cells and modules, production techniques, and system design, was initiated by a cooperative effort of the US Government and the domestic PV manufacturers. European and Japanese firms entered the PV industry later, but are also growing rapidy. The Europeans continue to supply PV systems for village electrification and water pumping to many Third World countries. The Japanese have been developing the amorphous silicon (A-Si) technology by expanding its use in consumer goods. The world PV industry saw dramatic changes in industry ownership and in the emphasis on developing new and improved technology during 1984. The objective of this report is to present information on the developments of the world PV industry and focuses on developments occurring in 1984. Information is presented on a regional basis (US, Europe, Japan, other) to avoid disclosing company-confidential data. All information was gleaned from several sources, including a review of the technical literature and direct contacts with PV manufacturers. Prior to publishing the regional totals, all numbers were compared with those of other sources. The information contained in this report is prepared for use by the Department of Energy for their use in long-term R and D planning. However, this information should also be of interest by PV manufacturers and to those who may be contemplating entering the PV market. PV shipments for 1984, government supports for PV, and various PV market sectors are discussed.

Watts, R.L.; Smith, S.A.; Dirks, J.A.

1985-04-01T23:59:59.000Z

415

Tobacco Industry Involvement in Colorado  

E-Print Network (OSTI)

Accessed May 25, 2004) Industry Summary. 1992 (est. ).11 May 2004) Tobacco Industry Involvement in Colorado Pageor (800) LUNG-USA. Tobacco Industry Involvement in Colorado

Landman, BA, Anne; Bialick, Peter

2004-01-01T23:59:59.000Z

416

For Industry | ornl.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

R&D accelerates battery technology | More news Home | Connect with ORNL | For Industry For Industry | For Industry SHARE There are a few different way of "working" with...

417

Utah's Coal Industry: Economic Contributions and Future Prospects  

E-Print Network (OSTI)

Utah's Coal Industry: Economic Contributions and Future Prospects Pamela S. Perlich, Senior's coal industry has played a significant role in the economic development of the state for well over developments. The first section of this paper presents an overview of the coal industry in Utah, examining

418

Biomass power industry: Assessment of key players and approaches for DOE and industry interaction  

DOE Green Energy (OSTI)

A review team established by the Department of Energy conducted an assessment of the US biomass power industry. The review team visited with more than 50 organizations representing all sectors of the biomass power industry including utilities, independent power producers, component manufacturers, engineering and construction contractors, agricultural organizations, industrial users, and regulatory organizations. DOE solicited industry input for the development of the Biomass Power Division`s Five Year Plan. DOE believed there was a critical need to obtain industry`s insight and working knowledge to develop the near- and long-term plans of the program. At the heart of this objective was the desire to identify near-term initiatives that the program could pursue to help accelerate the further development of biomass power projects.

Not Available

1994-01-01T23:59:59.000Z

419

Equity Industrial Partners | Open Energy Information  

Open Energy Info (EERE)

Equity Industrial Partners Equity Industrial Partners Jump to: navigation, search Name Equity Industrial Partners Facility Equity Industrial Partners Sector Wind energy Facility Type Community Wind Facility Status In Service Owner Equity Industrial Turbines LLC Developer Equity Industrial Turbines LLC Energy Purchaser City of Gloucester Location Gloucester MA Coordinates 42.625864°, -70.65621° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.625864,"lon":-70.65621,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

420

Technology assessment of offshore industry. The United States offshore industry. Current status, trends and forecast 1976-2000. Volume I. Final report  

SciTech Connect

Volume One presents a description of the current status of the U.S. offshore industry together with developing trends in the industry and an examination of the various forces that influence development. A 25 year forecast of offshore industry development is included. Also included is a description of the U.S. commercial ocean fishing industry and a 25 year forecast of industry development.

Durfee, J.H.

1977-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

PIA - Industry Interactive Procurement System (IIPS) | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Industry Interactive Procurement System (IIPS) PIA - Industry Interactive Procurement System (IIPS) PIA - Industry Interactive Procurement System (IIPS) PIA - Industry Interactive...

422

Current and future industrial energy service characterizations  

DOE Green Energy (OSTI)

Current and future energy demands, end uses, and cost used to characterize typical applications and resultant services in the industrial sector of the United States and 15 selected states are examined. A review and evaluation of existing industrial energy data bases was undertaken to assess their potential for supporting SERI research on: (1) market suitability analysis, (2) market development, (3) end-use matching, (3) industrial applications case studies, and (4) identification of cost and performance goals for solar systems and typical information requirements for industrial energy end use. In reviewing existing industrial energy data bases, the level of detail, disaggregation, and primary sources of information were examined. The focus was on fuels and electric energy used for heat and power purchased by the manufacturing subsector and listed by 2-, 3-, and 4-digit SIC, primary fuel, and end use. Projections of state level energy prices to 1990 are developed using the energy intensity approach. The effects of federal and state industrial energy conservation programs on future industrial sector demands were assessed. Future end-use energy requirements were developed for each 4-digit SIC industry and were grouped as follows: (1) hot water, (2) steam (212 to 300/sup 0/F, each 100/sup 0/F interval from 300 to 1000/sup 0/F, and greater than 1000/sup 0/F), and (3) hot air (100/sup 0/F intervals). Volume I details the activities performed in this effort.

Krawiec, F.; Thomas, T.; Jackson, F.; Limaye, D.R.; Isser, S.; Karnofsky, K.; Davis, T.D.

1980-10-01T23:59:59.000Z

423

U.S. Industrial Energy Efficiency Programs  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Second U.S.-China Second U.S.-China Energy Efficiency Forum May 6, 2011 James Quinn Energy Efficiency & Renewable Energy U.S. Department of Energy U.S. Industrial Energy Efficiency Programs 2 | Industrial Energy Efficiency eere.energy.gov Global Energy Challenges Energy efficiency and renewable energy provide solutions to global energy challenges. Security Environment Economy Clean Energy Solutions Overarching Challenges: * Carbon reduction * Market delivery of clean energy technologies * Research and development needs * Economic growth * Workforce development 3 | Industrial Energy Efficiency eere.energy.gov U.S. industry accounts for about one-third of all U.S. energy consumption. Petroleum Natural Gas Electricity* Coal and Coke Renewable Energy Residential 21.8% Industry 31.4% Commercial

424

Role of fuel cells in industrial cogeneration  

SciTech Connect

During the early years (1958 to 1963), three types of fuel cells were under development: phosphoric acid (PAFC), molten carbonate (MCFC), and solid oxide (SOFC) fuel cells. Between 1963 and 1971, the IGT research and development effort concentrated on the phosphoric acid and molten carbonate technologies; since 1971, emphasis has been on the molten carbonate fuel cell. IGT believes MCFC is best suited to meet the goals of the electric industry and the requirements of industrial cogeneration. Through the years, IGT has conducted system studies to evaluate the role that each one of the three fuel cell types can play in industrial cogeneration. This paper briefly discusses the status of the three technologies, the potential industrial cogeneration market, the application of fuel cells to this market, and the potential fuel savings for several industrial categories.

Camara, E.H.

1985-01-01T23:59:59.000Z

425

Effective Transfer of Industrial Energy Conservation Technologies  

E-Print Network (OSTI)

Voluntary participation in industrial energy conservation programs resulted in savings of approximately 1 million barrels of oil equivalent per day in the U.S. during 1981. These energy savings accrued largely from the development, introduction, and acceptance by industry of new energy conserving technologies. These new technologies were developed through cost sharing programs between the Department of Energy and private industry. These joint efforts reduced the risk to industry, thus making them willing to accept and use these new technologies at an accelerated rate. Examples of several technologies that were used by industry at an accelerated rate are described in this paper. These technologies are; textile foam finishing and dyeing, forging furnace modifications, and high efficiency metallic recuperators.

Clement, M.; Vallario, R. W.

1983-01-01T23:59:59.000Z

426

Evaluating Sites for Industrial Cogeneration in Chicago  

E-Print Network (OSTI)

Cogeneration is an industrial energy conservation technology that is particularly suited to urban applications. Large cities and metropolitan areas have large numbers of energy intensive industrial firms as well as commercial buildings; universities and hospital complexes; and new, densely populated residential developments that have large thermal and electric demands. Potential sites have been evaluated as part of a project to encourage industrial cogeneration applications in Chicago. Energy-intensive industries and commercial, industrial, and residential facilities were grouped by energy use type. Natural gas and electricity consumption data then were used to develop energy use profiles by energy use type and location. Complementary thermal energy use profiles and the geographical proximity of firms and facilities were used to exclude unfavorable sites. Thirty-four sites were then evaluated in detail and ranked according to their suitability for consideration in detailed feasibility studies of different cogeneration technologies.

Fowler, G. L.; Baugher, A. H.

1982-01-01T23:59:59.000Z

427

MISR -- Solar and steam for industry  

SciTech Connect

The goal of the MISR project is to assist industry in developing viable Solar Energy Systems which have high reliability and low cost because they do not require custom engineering and installation for each industrial site. The collector field, piping and steam generation equipment are pre-engineered to be suitable for a wide range of industrial steam applications. The approach of the MISR project is twofold: to develop line-focus industrial solar thermal energy systems which, like conventional packaged steam boilers, are based on the modular concept; and to install and operate a number (10 or less) of these systems at existing industrial plants, supplementing steam produced by conventional boilers. The project is briefly described.

1981-12-31T23:59:59.000Z

428

Industrial | OpenEI  

Open Energy Info (EERE)

Industrial Industrial Dataset Summary Description The Industrial Assessment Centers (IAC) Database is a collection of all the publicly available data from energy efficiency assessments conducted by IACs at small and medium-sized industrial facilities. Source Department of Energy Industrial Assessment Centers Date Released September 20th, 2012 (2 years ago) Date Updated September 20th, 2012 (2 years ago) Keywords assessment energy efficiency Industrial manufacturing small and medium-sized Data application/vnd.ms-excel icon copy_of_iac_database.xls (xls, 28.7 MiB) Quality Metrics Level of Review Standards Comment Temporal and Spatial Coverage Frequency Daily Time Period License License Open Data Commons Public Domain Dedication and Licence (PDDL) Comment Rate this dataset

429

LASER Welding Survey for Power Generation Industry  

Science Conference Proceedings (OSTI)

EPRI has developed technology for laser weld repair of steam generator tubes in light water reactors. This technology has promise for other specialized welding and heat treatment applications in the power generation industry.

1998-04-23T23:59:59.000Z

430

Essays concerning the cellulosic biofuel industry.  

E-Print Network (OSTI)

??Despite market-based incentives and mandated production, the U.S. cellulosic biofuel industry has been slow to develop. This dissertation explores the economic factors that have limited (more)

Rosburg, Alicia Sue

2012-01-01T23:59:59.000Z

431

Industrial Energy Efficiency Assessments  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Efficiency Energy Efficiency Assessments Lynn Price Staff Scientist China Energy Group Energy Analysis Department Environmental Energy Technologies Division Lawrence Berkeley National Laboratory Industrial Energy Efficiency Assessments - Definition and overview of key components - International experience - Chinese situation and recommendations - US-China collaboration Industrial Energy Efficiency Assessments - Analysis of the use of energy and potential for energy efficiency in an industrial facility * Current situation * Recommendations for improving energy efficiency * Cost-benefit analysis of recommended options * An action plan for realizing potential savings Types of Industrial Energy Efficiency Assessments - Preliminary or walk-through - Detailed or diagnostic Audit criteria

432

Industrial Partnerships Office  

Industrial Partnerships Office 6/13 Richard Rankin Director----Roger Werne Deputy Director-----Yvonne King Administrator Nina Potter Manager Intellectual Property

433

Industrial Waste Generation  

NLE Websites -- All DOE Office Websites (Extended Search)

9) Page 2 of 7 Industrial Waste Generation Work with Engineered Nanomaterials Power Consumption Historical Contamination (groundwater, soil) Hazardous Waste Generation Atmospheric...

434

Search - Industrial Partnerships Office  

Industrial Partnerships Office P.O. Box 808, L-795 Livermore, CA 94551 Phone: (925) 422-6416 Fax: (925) 423-8988 Operated by Lawrence Livermore ...

435

Construction Industry Software  

Science Conference Proceedings (OSTI)

... Translates a CIS/2 (CIMsteel Integration Standards) file into a 3D interactive VRML model of a steel structure or an IFC (Industry Foundation Classes ...

2012-04-23T23:59:59.000Z

436

Technologies - Industrial Partnerships Office  

Energy, Utilities, & Power Systems. Industrial Partnerships Office P.O. Box 808, L-795 Livermore, CA 94551 Phone: (925) 422-6416 Fax: (925) 423-8988

437

OpenEI - Industrial  

Open Energy Info (EERE)

renewable energy consumption (in quadrillion btu) for electricity generation in the United States by energy use sector (commercial, industrial and electric power) and by...

438

Biodiesel SRM Development  

Science Conference Proceedings (OSTI)

... and Industrial Quality (INMETRO) on the development of the certified reference materials (CRMs) for biofuels, specifically bioethanol and biodiesel ...

2013-02-11T23:59:59.000Z

439

Industrial energy efficiency policy in China  

SciTech Connect

Chinese industrial sector energy-efficiency policy has gone through a number of distinct phases since the founding of the People s Republic in 1949. An initial period of energy supply growth in the 1950s, 1960s, and 1970s was followed by implementation of significant energy efficiency programs in the 1980s. Many of these programs were dismantled in the 1990s during the continuing move towards a market-based economy. In an effort to once again strengthen energy efficiency, the Chinese government passes the Energy Conservation Law in 1997 which provides broad guidance for the establishment of energy efficiency policies. Article 20 of the Energy Conservation Law requires substantial improvement in industrial energy efficiency in the key energy-consuming industrial facilities in China. This portion of the Law declares that ''the State will enhance energy conservation management in key energy consuming entities.'' In 1999, the industrial sector consumed nearly 30 EJ, or 76 percent of China's primary energy. Even though primary energy consumption has dropped dramatically in recent years, due mostly to a decline in coal consumption, the Chinese government is still actively developing an overall policy for energy efficiency in the industrial sector modeled after policies in a number of industrialized countries. This paper will describe recent Chinese government activities to develop industrial sector energy-efficiency targets as a ''market-based'' mechanism for improving the energy efficiency of key industrial facilities.

Price, Lynn; Worrell, Ernst; Sinton, Jonathan; Yun, Jiang

2001-05-01T23:59:59.000Z

440

Geothermal industry assessment  

DOE Green Energy (OSTI)

An assessment of the geothermal industry is presented, focusing on industry structure, corporate activities and strategies, and detailed analysis of the technological, economic, financial, and institutional issues important to government policy formulation. The study is based principally on confidential interviews with executives of 75 companies active in the field. (MHR)

Not Available

1980-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Industry - ORNL Neutron Sciences  

NLE Websites -- All DOE Office Websites (Extended Search)

Industry and Neutron Science Industry and Neutron Science Industry and Neutron Science: Working To Make a Match "In fundamental research, we want to know everything. Industry wants to know enough to answer a question." Research Contact: Mike Crawford September 2011, Written by Deborah Counce Mike Crawford and Souleymane Diallo Mike Crawford of Dupont (right) and Souleymane Diallo, instrument scientist for the Backscattering Spectrometer at SNS, prepare a material sample for an experiment on the instrument. Industrial users are starting to eye the potential of neutron science for solving problems that can't be solved in any other way. At the same time, the SNS and HFIR neutron science facilities at ORNL are exploring ways to woo such users and to make a match of it, to the benefit of both.

442

Uranium industry annual 1996  

SciTech Connect

The Uranium Industry Annual 1996 (UIA 1996) provides current statistical data on the US uranium industry`s activities relating to uranium raw materials and uranium marketing. The UIA 1996 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. Data on uranium raw materials activities for 1987 through 1996 including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2006, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, uranium imports and exports, and uranium inventories are shown in Chapter 2. A feature article, The Role of Thorium in Nuclear Energy, is included. 24 figs., 56 tabs.

NONE

1997-04-01T23:59:59.000Z

443

Uranium industry annual 1995  

SciTech Connect

The Uranium Industry Annual 1995 (UIA 1995) provides current statistical data on the U.S. uranium industry`s activities relating to uranium raw materials and uranium marketing. The UIA 1995 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. It contains data for the period 1986 through 2005 as collected on the Form EIA-858, ``Uranium Industry Annual Survey``. Data collected on the ``Uranium Industry Annual Survey`` provide a comprehensive statistical characterization of the industry`s plans and commitments for the near-term future. Where aggregate data are presented in the UIA 1995, care has been taken to protect the confidentiality of company-specific information while still conveying accurate and complete statistical data. Data on uranium raw materials activities for 1986 through 1995 including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2005, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, uranium imports and exports, and uranium inventories are shown in Chapter 2. The methodology used in the 1995 survey, including data edit and analysis, is described in Appendix A. The methodologies for estimation of resources and reserves are described in Appendix B. A list of respondents to the ``Uranium Industry Annual Survey`` is provided in Appendix C. For the reader`s convenience, metric versions of selected tables from Chapters 1 and 2 are presented in Appendix D along with the standard conversion factors used. A glossary of technical terms is at the end of the report. 14 figs., 56 tabs.

NONE

1996-05-01T23:59:59.000Z

444

Fermilab | Science at Fermilab | Benefits to Society | Industry  

NLE Websites -- All DOE Office Websites (Extended Search)

Industry Industry Industry: power transmission Industry: power transmission Cables made of superconducting material can carry far more electricity than conventional cables with minimal power losses. Underground copper transmission lines or power cables are near their capacity in many densely populated areas, and superconducting cables offer an opportunity to meet continued need. Further superconducting technology advances in particle physics will help contribute to this nascent industry. Industry: transportation Magnetically levitating trains use powerful superconducting magnets to suspend and propel the train. Mag-lev trains are fast and quiet compared to wheeled mass-transit systems, potentially reaching velocities comparable to jet aircraft. The superconducting magnet technology developed for particle

445

FAQS Qualification Card - Industrial Hygiene | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FAQS Qualification Card - Industrial Hygiene FAQS Qualification Card - Industrial Hygiene FAQS Qualification Card - Industrial Hygiene A key element for the Department's Technical Qualification Programs is a set of common Functional Area Qualification Standards (FAQS) and associated Job Task Analyses (JTA). These standards are developed for various functional areas of responsibility in the Department, including oversight of safety management programs identified as hazard controls in Documented Safety Analyses (DSA). For each functional area, the FAQS identify the minimum technical competencies and supporting knowledge and skills for a typical qualified individual working in the area. FAQC-IndustrialHygiene.docx Description Industrial Hygiene Qualification Card More Documents & Publications FAQS Gap Analysis Qualification Card - Industrial Hygiene

446

China-International Industrial Energy Efficiency Deployment Project | Open  

Open Energy Info (EERE)

China-International Industrial Energy Efficiency Deployment Project China-International Industrial Energy Efficiency Deployment Project Jump to: navigation, search Name China-International Industrial Energy Efficiency Deployment Project Agency/Company /Organization United States Department of Energy (USDOE), Institute for Sustainable Communities (ISC), Lawrence Berkeley National Laboratory, Oak Ridge National Laboratory (ORNL), Alliance for Energy Efficient Economy (India), Confederation of Indian Industry Sector Energy Focus Area Industry Topics Implementation, Low emission development planning, Technology characterizations Program Start 2011 Program End 2013 Country China Eastern Asia References International Industrial Energy Efficiency Deployment Project[1] Overview China "China is prioritizing a low carbon, energy efficient economy and has

447

International Industrial Energy Efficiency Deployment Project | Open Energy  

Open Energy Info (EERE)

Industrial Energy Efficiency Deployment Project Industrial Energy Efficiency Deployment Project Jump to: navigation, search Name International Industrial Energy Efficiency Deployment Project Agency/Company /Organization United States Department of Energy (USDOE), Institute for Sustainable Communities (ISC), Lawrence Berkeley National Laboratory, Oak Ridge National Laboratory (ORNL), Alliance for Energy Efficient Economy (India), Confederation of Indian Industry Sector Energy Focus Area Industry Topics Implementation, Low emission development planning, Technology characterizations Program Start 2011 Program End 2013 Country China, India Eastern Asia, Southern Asia References International Industrial Energy Efficiency Deployment Project[1] Overview China "China is prioritizing a low carbon, energy efficient economy and has

448

Local Option - Industrial Facilities and Development Bonds |...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Water Water Heating Wind Maximum Rebate Locally Determined Program Information Utah Program Type State Bond Program Rebate Amount Locally Determined Under the Utah...

449

Industrial Business Development - Los Alamos National Lab ...  

Los Alamos National Laboratory, an af?rmative action/ equal opportunity employer, is operated by the University of California for the U.S. Department of Energy under

450

AMO Industrial Distributed Energy: Research and Development  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

reciprocating engine systems (ARES), packaged CHP systems, high-value applications, fuel-flexible CHP, waste energy recovery systems, and demonstrations of these technologies....

451

Energy Financing Industrial Development Bond Program (California...  

Open Energy Info (EERE)

include photovoltaics, solar thermal electric, fuel cells, small and large wind turbines, biogas, landfill gas, biomass, and geothermal electric technologies. Funding for...

452

Illinois Coal Development Program (Illinois) | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Illinois Coal Development Program (Illinois) Illinois Coal Development Program (Illinois) < Back Eligibility Commercial Construction Developer Industrial Program Info State...

453

Zero emissions systems in the food processing industry  

Science Conference Proceedings (OSTI)

The food processing industry is part of an interlinked group of sectors. It plays an important role in the economic development of every country. However, a strongly growing food processing industry greatly magnifies the problems of waste management, ... Keywords: anaerobic digestion, food processing industry, pineapple waste, zero emissions system

Uyen Nguyen Ngoc; Hans Schnitzer

2008-02-01T23:59:59.000Z

454

Modeling Atlantic salmon fish farming industry: freshwater sub model simulation  

Science Conference Proceedings (OSTI)

Atlantic salmon fish farming has become a large industry worldwide. The industry's processes are examined, and the farming stages analyzed. Fish Farming Industry Simulation Model (FFISiM), a hierarchical, colored Petri net simulation model, was developed ... Keywords: Petri nets, cost and timing, fish farming, growth, performance analysis

Rune Melberg; Reggie Davidrajuh

2009-03-01T23:59:59.000Z

455

Status of the LNG industry  

Science Conference Proceedings (OSTI)

A status report on the liquefied natural gas (LNG) industry after 22 years of international trade compares developments during 1984-1985 for the major exporting and importing countries. Japan, the leading consumer, imports over 72% of the world production, while Europe imports 27% and the US 1%. There are 10 baseload liquefaction plants with a collective capacity of about 230 million m/sup 3//streamday. Japan has 85% of the world's LNG storage facilities because its geology is not suitable for underground storage. Utilities are looking to LNG for peakshaving, but it will be necessary to time projects so that production and demand will develop a reliable trade climate. 3 tables.

Anderson, P.J.

1986-06-30T23:59:59.000Z

456

NSLS Industrial User Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Jun Wang Physicist, Industrial Program Coordinator Phone: 344-2661 Email: junwang@bnl.gov Jun Wang is an Industrial Program Coordinator in the Photon Science Directorate at Brookhaven National Laboratory. She is working closely with industrial researchers as well as beamline staff to identify and explore new opportunities in industrial applications using synchrotron radiation. She has been leading the industrial research program including consultation, collaboration and outreach to the industrial user groups. Before joining BNL in 2008, Jun Wang was a Lead Scientist for a high-resolution high throughput powder diffraction program at the Advanced Photon Source (APS). As a Physicist at BNL, her research focuses on materials structure determination and evolution. Her expertise covers wide range x-ray techniques such as thin film x-ray diffraction and reflectivity, powder diffraction, small angle x-ray scattering, protein solution scattering and protein crystallography, as well as x-ray imaging. Currently she is the project leader of a multi-million dollar project on transmission x-ray microscopy recently funded by the U.S. DOE and the spokesperson for this new imaging beamline at the NSLS. She has also been collaborating with universities and industries for several projects on energy research at the NSLS.

457

Emerging Industrial Innovations for New Energy Efficient Technologies  

E-Print Network (OSTI)

The discussion surrounding industrial efficiency gains typically focuses on industrys own use of energy and the set of technologies that might cost-effectively reduce that consumption. Often overlooked is industrys role as a primary developer of the materials and technologies that can generate large efficiency gains within all other sectors of the economy. For example, its role in developing a new generation of fuel cell vehicles, on demand manufacturing capabilities, or new plastics that double as integrated photovoltaic systems may play an even larger role in the more productive use of our energy resources. This paper explores recent work on industrial innovation, often involving public-private partnerships, and provides a context to understand the role of innovation. It highlights a number of emerging technologies that may foster an even greater energy savings than might be apparent from looking at industrys own energy use patterns alone.

Laitner, J. A.

2007-01-01T23:59:59.000Z

458

Industrial process surveillance system  

DOE Patents (OSTI)

A system and method for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy.

Gross, Kenneth C. (Bolingbrook, IL); Wegerich, Stephan W. (Glendale Heights, IL); Singer, Ralph M. (Naperville, IL); Mott, Jack E. (Idaho Falls, ID)

1998-01-01T23:59:59.000Z

459

Industrial Process Surveillance System  

DOE Patents (OSTI)

A system and method for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy.

Gross, Kenneth C. (Bolingbrook, IL); Wegerich, Stephan W (Glendale Heights, IL); Singer, Ralph M. (Naperville, IL); Mott, Jack E. (Idaho Falls, ID)

2001-01-30T23:59:59.000Z

460

Industrial process surveillance system  

DOE Patents (OSTI)

A system and method are disclosed for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy. 96 figs.

Gross, K.C.; Wegerich, S.W.; Singer, R.M.; Mott, J.E.

1998-06-09T23:59:59.000Z

Note: This page contains sample records for the topic "optoelectronics industry development" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Biomass energy conversion workshop for industrial executives  

DOE Green Energy (OSTI)

The rising costs of energy and the risks of uncertain energy supplies are increasingly familiar problems in industry. Bottom line profits and even the simple ability to operate can be affected by spiralling energy costs. An often overlooked alternative is the potential to turn industrial waste or residue into an energy source. On April 9 and 10, 1979, in Claremont, California, the Solar Energy Research Institute (SERI), the California Energy Commission (CEC), and the Western Solar Utilization Network (WSUN) held a workshop which provided industrial managers with current information on using residues and wastes as industrial energy sources. Successful industrial experiences were described by managers from the food processing and forest product industries, and direct combustion and low-Btu gasification equipment was described in detail. These speakers' presentations are contained in this document. Some major conclusions of the conference were: numerous current industrial applications of wastes and residues as fuels are economic and reliable; off-the-shelf technologies exist for converting biomass wastes and residues to energy; a variety of financial (tax credits) and institutional (PUC rate structures) incentives can help make these waste-to-energy projects more attractive to industry. However, many of these incentives are still being developed and their precise impact must be evaluated on a case-by-case basis.

None

1979-01-01T23:59:59.000Z

462

Center for Productivity Innovation's Student Project with Industry Program at the University of Tennessee, Department of Industrial and Systems Engineering  

Science Conference Proceedings (OSTI)

A robust graduate engineering education experience requires students to learn the fundamental subject knowledge, to develop their ability to apply what they know to actual projects, and to contribute to the current body of knowledge by writing theses ... Keywords: Student Projects with Industry, engineering education, graduate research and education, industrial engineering, industry-university interaction

Rapinder Sawhney, Sima Maleki, Joseph Wilck, Pedraum Hashemian

2013-01-01T23:59:59.000Z

463

Firm Size and Industry Structure Under Human Capital Intensity: Insights from the Evolution of the Global Advertising Industry  

Science Conference Proceedings (OSTI)

Although existing literature assumes that the human capital intensity of professional services leads to small and flimsy firms, several professional services feature large, long-lived firms. To develop insights about firm size and industry structure ... Keywords: advertising agencies, financial intermediation, human capital, industry evolution, industry structure, professional services, vertical differentiation

Andrew von Nordenflycht

2011-01-01T23:59:59.000Z

464

Optoelectronic Manufacturing Group Homepage  

Science Conference Proceedings (OSTI)

... ConversionNanostructures are a critical component of innovations in electronics, energy conservation, renewable energy, biomedical research ...

2011-11-07T23:59:59.000Z

465

Ceramics for ATS industrial turbines  

DOE Green Energy (OSTI)

US DOE and most US manufacturers of stationary gas turbines are participating in a major national effort to develop advanced turbine systems (ATS). The ATS program will achieve ultrahigh efficiencies, environmental superiority, and cost competitiveness compared with current combustion turbine systems. A major factor in the improved efficiencies of simple cycle ATS gas turbines will be higher operating efficiencies than curren engines. These temperatures strain the limits of metallic alloy and flow-path cooling technologies. Ceramics materials offer a potential alterative to cooled turbine alloys for ATS turbines due to higher melting points than metallics. This paper evaluates ceramics technology and plant economic issues for ATS industrial turbine systems. A program with the objective of demonstrating first-stage ceramic vanes in a commerical industrial turbine is also described.

Wenglarz, R.; Ali, S. [Allison Engine Co., Indianapolis, IN (United States); Layne, A. [USDOE Morgantown Energy Technology Center, WV (United States)

1996-05-01T23:59:59.000Z

466

Advanced Industrial Materials (AIM) Program annual progress report, FY 1997  

SciTech Connect

The Advanced Industrial Materials (AIM) Program is a part of the Office of Industrial Technologies (OIT), Energy Efficiency and Renewable Energy, US Department of Energy (DOE). The mission of AIM is to support development and commercialization of new or improved materials to improve energy efficiency, productivity, product quality, and reduced waste in the major process industries. OIT has embarked on a fundamentally new way of working with industries--the Industries of the Future (IOF) strategy--concentrating on the major process industries that consume about 90% of the energy and generate about 90% of the waste in the industrial sector. These are the aluminum, chemical, forest products, glass, metalcasting, and steel industries. OIT has encouraged and assisted these industries in developing visions of what they will be like 20 or 30 years into the future, defining the drivers, technology needs, and barriers to realization of their visions. These visions provide a framework for development of technology roadmaps and implementation plans, some of which have been completed. The AIM Program supports IOF by conducting research and development on materials to solve problems identified in the roadmaps. This is done by National Laboratory/industry/university teams with the facilities and expertise needed to develop new and improved materials. Each project in the AIM Program has active industrial participation and support.

NONE

1998-05-01T23:59:59.000Z

467

Idle Industrial Sites Redevelopment (Wisconsin) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Idle Industrial Sites Redevelopment (Wisconsin) Idle Industrial Sites Redevelopment (Wisconsin) Idle Industrial Sites Redevelopment (Wisconsin) < Back Eligibility Developer Institutional Local Government Nonprofit State/Provincial Govt Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Wisconsin Program Type Grant Program Provider Wisconsin Economic Development Corporation The Idle Industrial Sites Redevelopment Program offers grants of up to $1,000,000 to Wisconsin communities for implementation of redevelopment plans for large industrial sites that have been idle, abandoned, or underutilized for a period of at least five years. Approved projects can use funds for demolition, environmental remediation, or site-specific