National Library of Energy BETA

Sample records for oak springs compressor

  1. Gas Spring Losses in Linear Clearance Seal Compressors P.B. Bailey, M.W. Dadd, J.S. Reed*

    E-Print Network [OSTI]

    1 Gas Spring Losses in Linear Clearance Seal Compressors P.B. Bailey, M.W. Dadd, J.S. Reed* , C, and the simplest demonstration of this can be observed in a gas spring. Our understanding of these gas spring with a clearance seal linear compressor attached to a plain gas spring volume. The static flow through

  2. Variable gas spring for matching power output from FPSE to load of refrigerant compressor

    DOE Patents [OSTI]

    Chen, Gong (Athens, OH); Beale, William T. (Athens, OH)

    1990-01-01

    The power output of a free piston Stirling engine is matched to a gas compressor which it drives and its stroke amplitude is made relatively constant as a function of power by connecting a gas spring to the drive linkage from the engine to the compressor. The gas spring is connected to the compressor through a passageway in which a valve is interposed. The valve is linked to the drive linkage so it is opened when the stroke amplitude exceeds a selected limit. This allows compressed gas to enter the spring, increase its spring constant, thus opposing stroke increase and reducing the phase lead of the displacer ahead of the piston to reduce power output and match it to a reduced load power demand.

  3. Variable gas spring for matching power output from FPSE to load of refrigerant compressor

    DOE Patents [OSTI]

    Chen, G.; Beale, W.T.

    1990-04-03

    The power output of a free piston Stirling engine is matched to a gas compressor which it drives and its stroke amplitude is made relatively constant as a function of power by connecting a gas spring to the drive linkage from the engine to the compressor. The gas spring is connected to the compressor through a passageway in which a valve is interposed. The valve is linked to the drive linkage so it is opened when the stroke amplitude exceeds a selected limit. This allows compressed gas to enter the spring, increase its spring constant, thus opposing stroke increase and reducing the phase lead of the displacer ahead of the piston to reduce power output and match it to a reduced load power demand. 6 figs.

  4. Centrifugal Compressors

    SciTech Connect (OSTI)

    Hastbacka, Mildred; Dieckmann, John; Bouza, Antonio

    2013-02-06

    The article discusses small high speed centrifugal compressors. This topic was covered in a previous ASHRAE Journal column (2003). This article reviews another configuration which has become an established product. The operation, energy savings and market potential of this offering are addressed as well.

  5. Supersonic compressor

    DOE Patents [OSTI]

    Lawlor, Shawn P. (Bellevue, WA); Novaresi, Mark A. (San Diego, CA); Cornelius, Charles C. (Kirkland, WA)

    2008-02-26

    A gas compressor based on the use of a driven rotor having an axially oriented compression ramp traveling at a local supersonic inlet velocity (based on the combination of inlet gas velocity and tangential speed of the ramp) which forms a supersonic shockwave axially, between adjacent strakes. In using this method to compress inlet gas, the supersonic compressor efficiently achieves high compression ratios while utilizing a compact, stabilized gasdynamic flow path. Operated at supersonic speeds, the inlet stabilizes an oblique/normal shock system in the gasdyanamic flow path formed between the gas compression ramp on a strake, the shock capture lip on the adjacent strake, and captures the resultant pressure within the stationary external housing while providing a diffuser downstream of the compression ramp.

  6. Hydride compressor

    DOE Patents [OSTI]

    Powell, James R. (Wading River, NY); Salzano, Francis J. (Patchogue, NY)

    1978-01-01

    Method of producing high energy pressurized gas working fluid power from a low energy, low temperature heat source, wherein the compression energy is gained by using the low energy heat source to desorb hydrogen gas from a metal hydride bed and the desorbed hydrogen for producing power is recycled to the bed, where it is re-adsorbed, with the recycling being powered by the low energy heat source. In one embodiment, the adsorption-desorption cycle provides a chemical compressor that is powered by the low energy heat source, and the compressor is connected to a regenerative gas turbine having a high energy, high temperature heat source with the recycling being powered by the low energy heat source.

  7. High Speed Compressors P.B. Bailey, M. W. Dadd, C. R. Stone.

    E-Print Network [OSTI]

    of the compressor. The `Oxford' type clearance seal/flexure bearing compressors are typically operated close to the main piston. Use of such a gas spring has some disadvantages: there is a second piston of small compact cryocooler compressors. INTRODUCTION The "Oxford" type of flexure bearing/clearance seal

  8. The effects of fall and spring burning on water quality and vegetative cover in the Post Oak Savannah of Texas 

    E-Print Network [OSTI]

    Garza, Nick Ernest

    1983-01-01

    assigned one of three treatments; unburned, fall burned and spring burned. Mean runoff tended to be greater from unburned plots than from burned plots although differences were seldom significant. Mean sedi- iv ment export (kg/ha) during the 18 month... study period was not signifi- cantly different between treatments, however, trends would suggest that spring burned plots lost lese soil than did fall burned or unburned plots. The data imply that greater loss of soil occurred during the dry season...

  9. TTTTThe Fhe Fhe Fhe Fhe Fossil Reportossil Reportossil Reportossil Reportossil Report Oak Ridge National Laboratory Fossil Energy Program Spring 2002

    E-Print Network [OSTI]

    Pennycook, Steve

    be widely used in the next generation of power plants, aiding the conversion of coal to clean gas. Our National Laboratory Fossil Energy Program Spring 2002 Energy Technology for the Future...and for the WorldElectronicNeedsforSolid Oxide Fuel Cells Largest Oil Deposit Ever in Gulf of Mexico New Technology Used for Monitoring Metals

  10. Recirculating rotary gas compressor

    DOE Patents [OSTI]

    Weinbrecht, John F. (601 Oakwood Loop, NE., Albuquerque, NM 87123)

    1992-01-01

    A positive displacement, recirculating Roots-type rotary gas compressor which operates on the basis of flow work compression. The compressor includes a pair of large diameter recirculation conduits (24 and 26) which return compressed discharge gas to the compressor housing (14), where it is mixed with low pressure inlet gas, thereby minimizing adiabatic heating of the gas. The compressor includes a pair of involutely lobed impellers (10 and 12) and an associated port configuration which together result in uninterrupted flow of recirculation gas. The large diameter recirculation conduits equalize gas flow velocities within the compressor and minimize gas flow losses. The compressor is particularly suited to applications requiring sustained operation at higher gas compression ratios than have previously been feasible with rotary pumps, and is particularly applicable to refrigeration or other applications requiring condensation of a vapor.

  11. Recirculating rotary gas compressor

    DOE Patents [OSTI]

    Weinbrecht, J.F.

    1992-02-25

    A positive displacement, recirculating Roots-type rotary gas compressor is described which operates on the basis of flow work compression. The compressor includes a pair of large diameter recirculation conduits which return compressed discharge gas to the compressor housing, where it is mixed with low pressure inlet gas, thereby minimizing adiabatic heating of the gas. The compressor includes a pair of involutely lobed impellers and an associated port configuration which together result in uninterrupted flow of recirculation gas. The large diameter recirculation conduits equalize gas flow velocities within the compressor and minimize gas flow losses. The compressor is particularly suited to applications requiring sustained operation at higher gas compression ratios than have previously been feasible with rotary pumps, and is particularly applicable to refrigeration or other applications requiring condensation of a vapor. 12 figs.

  12. High ratio recirculating gas compressor

    DOE Patents [OSTI]

    Weinbrecht, John F. (601 Oakwood Pl., NE., Albuquerque, NM 87123)

    1989-01-01

    A high ratio positive displacement recirculating rotary compressor is disclosed. The compressor includes an integral heat exchanger and recirculation conduits for returning cooled, high pressure discharge gas to the compressor housing to reducing heating of the compressor and enable higher pressure ratios to be sustained. The compressor features a recirculation system which results in continuous and uninterrupted flow of recirculation gas to the compressor with no direct leakage to either the discharge port or the intake port of the compressor, resulting in a capability of higher sustained pressure ratios without overheating of the compressor.

  13. High ratio recirculating gas compressor

    DOE Patents [OSTI]

    Weinbrecht, J.F.

    1989-08-22

    A high ratio positive displacement recirculating rotary compressor is disclosed. The compressor includes an integral heat exchanger and recirculation conduits for returning cooled, high pressure discharge gas to the compressor housing to reducing heating of the compressor and enable higher pressure ratios to be sustained. The compressor features a recirculation system which results in continuous and uninterrupted flow of recirculation gas to the compressor with no direct leakage to either the discharge port or the intake port of the compressor, resulting in a capability of higher sustained pressure ratios without overheating of the compressor. 10 figs.

  14. Supersonic gas compressor

    DOE Patents [OSTI]

    Lawlor, Shawn P. (Bellevue, WA); Novaresi, Mark A. (San Diego, CA); Cornelius, Charles C. (Kirkland, WA)

    2007-11-13

    A gas compressor based on the use of a driven rotor having a compression ramp traveling at a local supersonic inlet velocity (based on the combination of inlet gas velocity and tangential speed of the ramp) which compresses inlet gas against a stationary sidewall. In using this method to compress inlet gas, the supersonic compressor efficiently achieves high compression ratios while utilizing a compact, stabilized gasdynamic flow path. Operated at supersonic speeds, the inlet stabilizes an oblique/normal shock system in the gasdyanamic flow path formed between the rim of the rotor, the strakes, and a stationary external housing. Part load efficiency is enhanced by the use of a pre-swirl compressor, and using a bypass stream to bleed a portion of the intermediate pressure gas after passing through the pre-swirl compressor back to the inlet of the pre-swirl compressor. Inlet guide vanes to the compression ramp enhance overall efficiency.

  15. Energy Savings for Centrifugal Compressors 

    E-Print Network [OSTI]

    Fisher, D.

    2011-01-01

    Current design improvements of both the rotating and stationary aerodynamic components of centrifugal compressors can greatly increase the efficiency of vintage machines. A centrifugal compressor built in the 1970's or 1980's might have an external...

  16. Standing wave compressor

    DOE Patents [OSTI]

    Lucas, Timothy S. (4614 River Mill Ct., Glen Allen, VA 23060)

    1991-01-01

    A compressor for compression-evaporation cooling systems, which requires no moving parts. A gaseous refrigerant inside a chamber is acoustically compressed and conveyed by means of a standing acoustic wave which is set up in the gaseous refrigerant. This standing acoustic wave can be driven either by a transducer, or by direct exposure of the gas to microwave and infrared sources, including solar energy. Input and output ports arranged along the chamber provide for the intake and discharge of the gaseous refrigerant. These ports can be provided with optional valve arrangements, so as to increase the compressor's pressure differential. The performance of the compressor in either of its transducer or electromagnetically driven configurations, can be optimized by a controlling circuit. This controlling circuit holds the wavelength of the standing acoustical wave constant, by changing the driving frequency in response to varying operating conditions.

  17. Compressor surge counter

    DOE Patents [OSTI]

    Castleberry, Kimberly N. (Harriman, TN)

    1983-01-01

    A surge counter for a rotating compressor is provided which detects surging by monitoring the vibration signal from an accelerometer mounted on the shaft bearing of the compressor. The circuit detects a rapid increase in the amplitude envelope of the vibration signal, e.g., 4 dB or greater in less than one second, which is associated with a surge onset and increments a counter. The circuit is rendered non-responsive for a period of about 5 seconds following the detection which corresponds to the duration of the surge condition. This prevents multiple registration of counts during the surge period due to rapid swings in vibration amplitude during the period.

  18. The Hydrogeologic Character of the Lower Tuff Confining Unit and the Oak Springs Butte Confining Unit in the Tuff Pile Area of Central Yucca Flat

    SciTech Connect (OSTI)

    Drellack, Jr., Sigmund L.; Prothro, Lance B.; Gonzales, Jose L.; Mercadante, Jennifer M.

    2010-07-30

    The lower tuff confining unit (LTCU) in the Yucca Flat Corrective Action Unit (CAU) consists of a monotonous sequence of pervasively zeolitized volcanic tuff (i.e., mostly bedded with lesser nonwelded to poorly welded tuff; not fractured) (Bechtel Nevada, 2006). The LTCU is an important confining unit beneath Yucca Flat because it separates the alluvial and volcanic aquifers, where many underground nuclear tests were conducted, from the regional lower carbonate aquifer. Recent sub-CAU-scale modeling by Los Alamos National Laboratory in the Tuff Pile area of Yucca Flat (Boryta, et al., in review) includes postulated low-porosity, high-permeability zones (i.e., fractured welded-tuff aquifers) within the LTCU. This scenario indicates that such postulated low-porosity, high-permeability zones could provide fast-path lateral conduits to faults, and eventually to the lower carbonate aquifer. A fractured and faulted lower carbonate aquifer is postulated to provide a flow path(s) for underground test-derived contaminants to potential offsite receptors. The ramifications of such a scenario are obvious for groundwater flow and contaminant migration beneath Yucca Flat. This paper describes the reasoning for not including postulated low-porosity, high-permeability zones within the LTCU in the Tuff Pile area or within the LTCU in the Yucca Flat CAU-scale model. Both observational and analytical data clearly indicate that the LTCU in the Tuff Pile area consists of pervasively zeolitic, nonwelded to poorly welded tuffs that are classified as tuff confining units (i.e., high-porosity, low-permeability). The position regarding the LTCU in the Tuff Pile area is summarized as follows: • The LTCU in the Tuff Pile area consists of a monotonous sequence of predominantly zeolitic nonwelded to poorly welded tuffs, and thus is accurately characterized hydrogeologically as a tuff confining unit (aquitard) in the Yucca Flat-Climax Mine hydrostratigraphic framework model (Bechtel Nevada, 2006). • No welded-tuff (or lava-flow aquifers), referred to as low-porosity, high-permeability zones in Boryta et al. (in review), are present within the LTCU in the Tuff Pile area. • Fractures within the LTCU are poorly developed, a characteristic of zeolitic tuffs; and fracture distributions are independent of stratigraphic and lithologic units (Prothro, 2008). • Groundwater flow and radionuclide transport will not be affected by laterally extensive zones of significantly higher permeability within the LTCU in the Tuff Pile area. Although not the primary focus of this report, the hydrogeologic character of the Oak Spring Butte confining unit (OSBCU), located directly below the LTCU, is also discussed. The OSBCU is lithologically more diverse, and does include nonwelded to partially welded ash-flow tuffs. However, these older ash-flow tuffs are poorly welded and altered (zeolitic to quartzofeldspathic), and consequently, would tend to have properties similar to a tuff confining unit rather than a welded-tuff aquifer.

  19. A COURSE ANNOUNCEMENT FOR SPRING 2002

    E-Print Network [OSTI]

    Camci, Cengiz

    aircraft engine compressors and turbines, spacecraft turbomachinery, ground based gas turbine systemsA COURSE ANNOUNCEMENT FOR SPRING 2002 Department of Aerospace Engineering THEORY & DESIGN, pumps and hydraulic turbines. ONE DIMENSIONAL ANALYSIS OF TURBOMACHINERY SYSTEMS OVERALL PERFORMANCE

  20. Light intensity compressor

    DOE Patents [OSTI]

    Rushford, Michael C. (Livermore, CA)

    1990-01-01

    In a system for recording images having vastly differing light intensities over the face of the image, a light intensity compressor is provided that utilizes the properties of twisted nematic liquid crystals to compress the image intensity. A photoconductor or photodiode material that is responsive to the wavelength of radiation being recorded is placed adjacent a layer of twisted nematic liquid crystal material. An electric potential applied to a pair of electrodes that are disposed outside of the liquid crystal/photoconductor arrangement to provide an electric field in the vicinity of the liquid crystal material. The electrodes are substantially transparent to the form of radiation being recorded. A pair of crossed polarizers are provided on opposite sides of the liquid crystal. The front polarizer linearly polarizes the light, while the back polarizer cooperates with the front polarizer and the liquid crystal material to compress the intensity of a viewed scene. Light incident upon the intensity compressor activates the photoconductor in proportion to the intensity of the light, thereby varying the field applied to the liquid crystal. The increased field causes the liquid crystal to have less of a twisting effect on the incident linearly polarized light, which will cause an increased percentage of the light to be absorbed by the back polarizer. The intensity of an image may be compressed by forming an image on the light intensity compressor.

  1. Advanced Hybrid Water Heater using Electrochemical Compressor...

    Energy Savers [EERE]

    Advanced Hybrid Water Heater using Electrochemical Compressor Advanced Hybrid Water Heater using Electrochemical Compressor Xergy is using its Electro Chemical Compression (ECC)...

  2. Dual capacity reciprocating compressor

    DOE Patents [OSTI]

    Wolfe, Robert W. (Wilkinsburg, PA)

    1984-01-01

    A multi-cylinder compressor 10 particularly useful in connection with northern climate heat pumps and in which different capacities are available in accordance with reversing motor 16 rotation is provided with an eccentric cam 38 on a crank pin 34 under a fraction of the connecting rods, and arranged for rotation upon the crank pin between opposite positions 180.degree. apart so that with cam rotation on the crank pin such that the crank throw is at its normal maximum value all pistons pump at full capacity, and with rotation of the crank shaft in the opposite direction the cam moves to a circumferential position on the crank pin such that the overall crank throw is zero. Pistons 24 whose connecting rods 30 ride on a crank pin 36 without a cam pump their normal rate with either crank rotational direction. Thus a small clearance volume is provided for any piston that moves when in either capacity mode of operation.

  3. Dual capacity reciprocating compressor

    DOE Patents [OSTI]

    Wolfe, R.W.

    1984-10-30

    A multi-cylinder compressor particularly useful in connection with northern climate heat pumps and in which different capacities are available in accordance with reversing motor rotation is provided with an eccentric cam on a crank pin under a fraction of the connecting rods, and arranged for rotation upon the crank pin between opposite positions 180[degree] apart so that with cam rotation on the crank pin such that the crank throw is at its normal maximum value all pistons pump at full capacity, and with rotation of the crank shaft in the opposite direction the cam moves to a circumferential position on the crank pin such that the overall crank throw is zero. Pistons whose connecting rods ride on a crank pin without a cam pump their normal rate with either crank rotational direction. Thus a small clearance volume is provided for any piston that moves when in either capacity mode of operation. 6 figs.

  4. Oak Ridge Office

    Office of Environmental Management (EM)

    PO. Box 2001 Oak Ridge, Tennessee 37831 July 21, 2010 Mr. Ron Murphree, Chair Oak Ridge Site Specific Advisory Board Post Office Box 200 1 Oak Ridge, Tennessee 3783 1 Dear Mr....

  5. Semi-active compressor valve

    DOE Patents [OSTI]

    Brun, Klaus (Helotes, TX); Gernentz, Ryan S. (San Antonio, TX)

    2010-07-27

    A method and system for fine-tuning the motion of suction or discharge valves associated with cylinders of a reciprocating gas compressor, such as the large compressors used for natural gas transmission. The valve's primary driving force is conventional, but the valve also uses an electromagnetic coil to sense position of the plate (or other plugging element) and to provide an opposing force prior to impact.

  6. Compressor bleed cooling fluid feed system

    DOE Patents [OSTI]

    Donahoo, Eric E; Ross, Christopher W

    2014-11-25

    A compressor bleed cooling fluid feed system for a turbine engine for directing cooling fluids from a compressor to a turbine airfoil cooling system to supply cooling fluids to one or more airfoils of a rotor assembly is disclosed. The compressor bleed cooling fluid feed system may enable cooling fluids to be exhausted from a compressor exhaust plenum through a downstream compressor bleed collection chamber and into the turbine airfoil cooling system. As such, the suction created in the compressor exhaust plenum mitigates boundary layer growth along the inner surface while providing flow of cooling fluids to the turbine airfoils.

  7. Power Characteristics of Industrial Air Compressors 

    E-Print Network [OSTI]

    Schmidt, C.; Kissock, K.

    2003-01-01

    common types of compressor control for small reciprocating and rotary air compressors, and derive relations for estimating compressed air output as a function of the type of control and motor loading. Using these relations, we develop a method to estimate...

  8. Economics of Electric Compressors for Gas Transmission 

    E-Print Network [OSTI]

    Schmeal, W. R.; Hibbs, J. J.

    1994-01-01

    Three new factors are coming together to motivate gas pipeline firms to consider electric motors for replacement of older reciprocating gas engines for compressor systems, and for new compressor installations. These factors are environmental...

  9. Water injected fuel cell system compressor

    DOE Patents [OSTI]

    Siepierski, James S. (Williamsville, NY); Moore, Barbara S. (Victor, NY); Hoch, Martin Monroe (Webster, NY)

    2001-01-01

    A fuel cell system including a dry compressor for pressurizing air supplied to the cathode side of the fuel cell. An injector sprays a controlled amount of water on to the compressor's rotor(s) to improve the energy efficiency of the compressor. The amount of water sprayed out the rotor(s) is controlled relative to the mass flow rate of air inputted to the compressor.

  10. Unique compressor passes field test

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    Revolutionary pipeline compression concept has proved successful at a Transcontinental Gas Pipe Line facility in Alabama. In April 1992, the MOPICO electric drive compressor completed 5,000 hours of successful operation at Transcontinental Gas Pipeline's Station 100 at Billingsley, Ala. The revolutionary gas pipeline compression concept eliminates many of the traditional complexities of a pipeline compressor station and has benefits not possible with conventional compressor systems. This paper reports that this is accomplished through the integration of technologies developed over the past 10 years into a design concept unique in the industry. Ross Hill Controls Inc., Houston, provides the adjustable-speed variable frequency drive unit that allows the electric motor to operate at speeds from 6,2000 rpm to 10,000 rpm. Transco Energy Ventures, a division of Transco Energy, participated in the development and assisted in placing the prototype unit on the Transcontinental Gas Pipeline system.

  11. OAK FMSXSE

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield Municipal Gas &SCE-SessionsSouthReport for the Weldon Spring,7=cr5rnP 7694 i+lJNew York,' ,9

  12. Multiple volume compressor for hot gas engine

    DOE Patents [OSTI]

    Stotts, Robert E. (Clifton Park, NY)

    1986-01-01

    A multiple volume compressor for use in a hot gas (Stirling) engine having a plurality of different volume chambers arranged to pump down the engine when decreased power is called for and return the working gas to a storage tank or reservoir. A valve actuated bypass loop is placed over each chamber which can be opened to return gas discharged from the chamber back to the inlet thereto. By selectively actuating the bypass valves, a number of different compressor capacities can be attained without changing compressor speed whereby the capacity of the compressor can be matched to the power available from the engine which is used to drive the compressor.

  13. Oak Ridge Office

    Office of Environmental Management (EM)

    - Mr. Steve Dixon, Chairman Oak Ridge Site Specific Advisory Board Post Office Box 200 1 Oak Ridge, Tennessee 3 783 0 Dear Mr. Dixon: RESPONSE TO RECOMMENDATION ON PROVIDING...

  14. Oil cooled, hermetic refrigerant compressor

    DOE Patents [OSTI]

    English, William A. (Murrysville, PA); Young, Robert R. (Murrysville, PA)

    1985-01-01

    A hermetic refrigerant compressor having an electric motor and compressor assembly in a hermetic shell is cooled by oil which is first cooled in an external cooler 18 and is then delivered through the shell to the top of the motor rotor 24 where most of it is flung radially outwardly within the confined space provided by the cap 50 which channels the flow of most of the oil around the top of the stator 26 and then out to a multiplicity of holes 52 to flow down to the sump and provide further cooling of the motor and compressor. Part of the oil descends internally of the motor to the annular chamber 58 to provide oil cooling of the lower part of the motor, with this oil exiting through vent hole 62 also to the sump. Suction gas with entrained oil and liquid refrigerant therein is delivered to an oil separator 68 from which the suction gas passes by a confined path in pipe 66 to the suction plenum 64 and the separated oil drops from the separator to the sump. By providing the oil cooling of the parts, the suction gas is not used for cooling purposes and accordingly increase in superheat is substantially avoided in the passage of the suction gas through the shell to the suction plenum 64.

  15. Oil cooled, hermetic refrigerant compressor

    DOE Patents [OSTI]

    English, W.A.; Young, R.R.

    1985-05-14

    A hermetic refrigerant compressor having an electric motor and compressor assembly in a hermetic shell is cooled by oil which is first cooled in an external cooler and is then delivered through the shell to the top of the motor rotor where most of it is flung radially outwardly within the confined space provided by the cap which channels the flow of most of the oil around the top of the stator and then out to a multiplicity of holes to flow down to the sump and provide further cooling of the motor and compressor. Part of the oil descends internally of the motor to the annular chamber to provide oil cooling of the lower part of the motor, with this oil exiting through vent hole also to the sump. Suction gas with entrained oil and liquid refrigerant therein is delivered to an oil separator from which the suction gas passes by a confined path in pipe to the suction plenum and the separated oil drops from the separator to the sump. By providing the oil cooling of the parts, the suction gas is not used for cooling purposes and accordingly increase in superheat is substantially avoided in the passage of the suction gas through the shell to the suction plenum. 3 figs.

  16. Digital Dynamic Range Compressor Design--A Tutorial and Analysis

    E-Print Network [OSTI]

    Reiss, Josh

    PAPERS Digital Dynamic Range Compressor Design-- A Tutorial and Analysis DIMITRIOS GIANNOULIS formal knowledge and analysis of compressor design techniques. In this tutorial we describe several become audio engineers' favorites for certain types of signal. The analysis of compressor designs

  17. Guide to Minimizing Compressor-Based Cooling | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Compressor-Based Cooling Guide to Minimizing Compressor-Based Cooling Guide describes best practices for reducing energy use and total cost of ownership for data center cooling...

  18. Low-Cost Electrochemical Compressor Utilizing Green Refrigerants...

    Office of Environmental Management (EM)

    Low-Cost Electrochemical Compressor Utilizing Green Refrigerants for HVAC Applications Low-Cost Electrochemical Compressor Utilizing Green Refrigerants for HVAC Applications...

  19. HELIUM COMPRESSOR MONITORING SYSTEM Donna Kubik

    E-Print Network [OSTI]

    HELIUM COMPRESSOR MONITORING SYSTEM Donna Kubik Arecibo Observatory #12;1 CONTENTS 1. Design goals for Phaseloss Detection Lambda +15V Power Supply Distribution Remote Control of 120VC to Compressor Monitoring System Fiber and Network Connections #12;3 1. Design goals Helium refrigerators cool the cryogenically

  20. Refrigeration system having standing wave compressor

    DOE Patents [OSTI]

    Lucas, Timothy S. (Glen Allen, VA)

    1992-01-01

    A compression-evaporation refrigeration system, wherein gaseous compression of the refrigerant is provided by a standing wave compressor. The standing wave compressor is modified so as to provide a separate subcooling system for the refrigerant, so that efficiency losses due to flashing are reduced. Subcooling occurs when heat exchange is provided between the refrigerant and a heat pumping surface, which is exposed to the standing acoustic wave within the standing wave compressor. A variable capacity and variable discharge pressure for the standing wave compressor is provided. A control circuit simultaneously varies the capacity and discharge pressure in response to changing operating conditions, thereby maintaining the minimum discharge pressure needed for condensation to occur at any time. Thus, the power consumption of the standing wave compressor is reduced and system efficiency is improved.

  1. Manager, Oak Ridge Office

    Broader source: Energy.gov [DOE]

    A successful candidate in this position will provide overall executive leadership to and integration of the Oak Ridge Integrated Support Center, which houses mission critical activities and support...

  2. Oakes College: An Oral History

    E-Print Network [OSTI]

    2011-01-01

    Oakes College: An Oral History Blake: That’s unfortunate. I’Oakes College: An Oral History Charland: It took awhile toOakes College: An Oral History with: J. Herman Blake Roberto

  3. Probabilistic Aerothermal Design of Compressor Airfoils Victor E. Garzon

    E-Print Network [OSTI]

    Peraire, Jaime

    and operating condition uncertainty on axial compressor performance. High-fidelity models of geometric-line multi-stage axial compressor model was used to estimate the impact of geometric variability on overall compressor performance. Probabilistic loss and turning models were exercised on a six-stage compressor model

  4. Compressor ported shroud for foil bearing cooling

    DOE Patents [OSTI]

    Elpern, David G. (Los Angeles, CA); McCabe, Niall (Torrance, CA); Gee, Mark (South Pasadena, CA)

    2011-08-02

    A compressor ported shroud takes compressed air from the shroud of the compressor before it is completely compressed and delivers it to foil bearings. The compressed air has a lower pressure and temperature than compressed outlet air. The lower temperature of the air means that less air needs to be bled off from the compressor to cool the foil bearings. This increases the overall system efficiency due to the reduced mass flow requirements of the lower temperature air. By taking the air at a lower pressure, less work is lost compressing the bearing cooling air.

  5. Oak Ridge Reservation Needs Assessment

    Broader source: Energy.gov [DOE]

    Needs Assessment for former Oak Ridge National Laboratory and Y-12 Nuclear Security Complex production workers.

  6. Robust design and tolerancing of compressor blades

    E-Print Network [OSTI]

    Dow, Eric Alexander

    2015-01-01

    Variations in the geometry of compressor blades can be introduced by variability in the manufacturing process or by in-service erosion. Recent research efforts have focused on characterizing the impacts of this geometric ...

  7. Method and apparatus for starting supersonic compressors

    DOE Patents [OSTI]

    Lawlor, Shawn P

    2013-08-06

    A supersonic gas compressor with bleed gas collectors, and a method of starting the compressor. The compressor includes aerodynamic duct(s) situated for rotary movement in a casing. The aerodynamic duct(s) generate a plurality of oblique shock waves for efficiently compressing a gas at supersonic conditions. A convergent inlet is provided adjacent to a bleed gas collector, and during startup of the compressor, bypass gas is removed from the convergent inlet via the bleed gas collector, to enable supersonic shock stabilization. Once the oblique shocks are stabilized at a selected inlet relative Mach number and pressure ratio, the bleed of bypass gas from the convergent inlet via the bypass gas collectors is effectively eliminated.

  8. Probabilistic analysis of meanline compressor rotor performance

    E-Print Network [OSTI]

    Fitzgerald, Nathan Andrew, 1980-

    2004-01-01

    This thesis addresses variability in aerodynamic performance of a compressor rotor due to geometric variation. The performance of the rotor is computed using a meanline model that includes the effect of tip clearance ...

  9. Cycling Losses During Screw Air Compressor Operation 

    E-Print Network [OSTI]

    Maxwell, J. B.; Wheeler, G.; Bushnell, D.

    1995-01-01

    Air compressors use 10-13 % of a typical industrial facilities' total electricity. Because they often operate at part load, their part load efficiency significantly affects plant energy cost. An intensive study of screw ...

  10. Probabilistic aerothermal design of compressor airfoils

    E-Print Network [OSTI]

    Garzón, Víctor E., 1972-

    2003-01-01

    Despite the generally accepted notion that geometric variability is undesirable in turbomachinery airfoils, little is known in detail about its impact on aerothermal compressor performance. In this work, statistical and ...

  11. A methodology for centrifugal compressor stability prediction

    E-Print Network [OSTI]

    Benneke, Björn

    2009-01-01

    The stable operation of centrifugal compressors is limited by well-known phenomena, rotating stall and surge. Although the manifestation of the full scale instabilities is similar to the ones observed in axial machines, ...

  12. Improved return passages for multistage centrifugal compressors

    E-Print Network [OSTI]

    Glass, Benjamin W., S.M. Massachusetts Institute of Technology

    2010-01-01

    This thesis presents a design concept for return passages in multistage centrifugal compressors. Flow in a baseline return passage is analyzed to identify loss sources that have substantial potential for reduction. For the ...

  13. Hydrogen pipeline compressors annual progress report.

    SciTech Connect (OSTI)

    Fenske, G. R.; Erck, R. A.

    2011-07-15

    The objectives are: (1) develop advanced materials and coatings for hydrogen pipeline compressors; (2) achieve greater reliability, greater efficiency, and lower capital in vestment and maintenance costs in hydrogen pipeline compressors; and (3) research existing and novel hydrogen compression technologies that can improve reliability, eliminate contamination, and reduce cost. Compressors are critical components used in the production and delivery of hydrogen. Current reciprocating compressors used for pipeline delivery of hydrogen are costly, are subject to excessive wear, have poor reliability, and often require the use of lubricants that can contaminate the hydrogen (used in fuel cells). Duplicate compressors may be required to assure availability. The primary objective of this project is to identify, and develop as required, advanced materials and coatings that can achieve the friction, wear, and reliability requirements for dynamically loaded components (seal and bearings) in high-temperature, high-pressure hydrogen environments prototypical of pipeline and forecourt compressor systems. The DOE Strategic Directions for Hydrogen Delivery Workshop identified critical needs in the development of advanced hydrogen compressors - notably, the need to minimize moving parts and to address wear through new designs (centrifugal, linear, guided rotor, and electrochemical) and improved compressor materials. The DOE is supporting several compressor design studies on hydrogen pipeline compression specifically addressing oil-free designs that demonstrate compression in the 0-500 psig to 800-1200 psig range with significant improvements in efficiency, contamination, and reliability/durability. One of the designs by Mohawk Innovative Technologies Inc. (MiTi{reg_sign}) involves using oil-free foil bearings and seals in a centrifual compressor, and MiTi{reg_sign} identified the development of bearings, seals, and oil-free tribological coatings as crucial to the successful development of an advanced compressor. MiTi{reg_sign} and ANL have developed potential coatings for these rigorous applications; however, the performance of these coatings (as well as the nickel-alloy substrates) in high-temperature, high-speed hydrogen environments is unknown at this point.

  14. Oak Ridge Office

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak of EnvironmentalY-12Oak I Oak

  15. RELAP5-3D Compressor Model

    SciTech Connect (OSTI)

    James E. Fisher; Cliff B. Davis; Walter L. Weaver

    2005-06-01

    A compressor model has been implemented in the RELAP5-3D© code. The model is similar to that of the existing pump model, and performs the same function on a gas as the pump performs on a single-phase or two-phase fluid. The compressor component consists of an inlet junction and a control volume, and optionally, an outlet junction. This feature permits cascading compressor components in series. The equations describing the physics of the compressor are derived from first principles. These equations are used to obtain the head, the torque, and the energy dissipation. Compressor performance is specified using a map, specific to the design of the machine, in terms of the ratio of outlet-to-inlet total (or stagnation) pressure and adiabatic efficiency as functions of rotational velocity and flow rate. The input quantities are specified in terms of dimensionless variables, which are corrected to stagnation density and stagnation sound speed. A small correction was formulated for the input of efficiency to account for the error introduced by assumption of constant density when integrating the momentum equation. Comparison of the results of steady-state operation of the compressor model to those of the MIT design calculation showed excellent agreement for both pressure ratio and power.

  16. Independent Oversight Review, Oak Ridge National Laboratory ...

    Energy Savers [EERE]

    Review, Oak Ridge National Laboratory - January 2013 Independent Oversight Review, Oak Ridge National Laboratory - January 2013 January 2013 Review of the Oak Ridge National...

  17. Xergy Ships First Breakthrough Water Heater Compressor to GE...

    Energy Savers [EERE]

    Xergy Ships First Breakthrough Water Heater Compressor to GE Xergy Ships First Breakthrough Water Heater Compressor to GE September 15, 2015 - 3:41pm Addthis Xergy Inc. and GE...

  18. Impact of geometric variability on compressor repeating-stage performance

    E-Print Network [OSTI]

    Vincent, Antoine, 1979-

    2003-01-01

    The impact of geometric variability on compressor performance is investigated using a compressor repeating-stage model based on well-known correlations for profile losses, endwall blockage, deviation, and the onset of ...

  19. Aerodynamic performance measurements in a counter-rotating aspirated compressor

    E-Print Network [OSTI]

    Onnée, Jean-François

    2005-01-01

    This thesis is an experimental investigation of the aerodynamic performances of a counter-rotating aspirated compressor. This compressor is implemented in a blow-down facility, which gives rigorous simulation of the ...

  20. Development of a body force model for centrifugal compressors

    E-Print Network [OSTI]

    Kottapalli, Anjaney Pramod

    2013-01-01

    This project is focused on modeling the internal ow in centrifugal compressors for the purpose of assessing the onset of rotating stall and surge. The current methods to determine centrifugal compressor stability limits ...

  1. Compressor airfoil tip clearance optimization system

    DOE Patents [OSTI]

    Little, David A.; Pu, Zhengxiang

    2015-08-18

    A compressor airfoil tip clearance optimization system for reducing a gap between a tip of a compressor airfoil and a radially adjacent component of a turbine engine is disclosed. The turbine engine may include ID and OD flowpath boundaries configured to minimize compressor airfoil tip clearances during turbine engine operation in cooperation with one or more clearance reduction systems that are configured to move the rotor assembly axially to reduce tip clearance. The configurations of the ID and OD flowpath boundaries enhance the effectiveness of the axial movement of the rotor assembly, which includes movement of the ID flowpath boundary. During operation of the turbine engine, the rotor assembly may be moved axially to increase the efficiency of the turbine engine.

  2. Active surge control of centrifugal compressors using drive torque

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    Active surge control of centrifugal compressors using drive torque Jan Tommy Gravdahl , Olav control is presented. A centrifugal compressor driven by an electrical motor is studied, and the drive of centrifugal com- pressors, which occurs when the operating point of the compressor is located to the left

  3. Method and apparatus for starting supersonic compressors

    DOE Patents [OSTI]

    Lawlor, Shawn P. (Bellevue, WA)

    2012-04-10

    A supersonic gas compressor. The compressor includes aerodynamic duct(s) situated on a rotor journaled in a casing. The aerodynamic duct(s) generate a plurality of oblique shock waves for efficiently compressing a gas at supersonic conditions. The convergent inlet is adjacent to a bleed air collector, and during acceleration of the rotor, bypass gas is removed from the convergent inlet via a collector to enable supersonic shock stabilization. Once the oblique shocks are stabilized at a selected inlet relative Mach number and pressure ratio, the bleed of bypass gas from the convergent inlet via the bypass gas collectors is eliminated.

  4. Oak Ridge Office

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak of EnvironmentalY-12Oak

  5. Oak Ridge Office

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak of EnvironmentalY-12Oak I

  6. Oak Ridge Office

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak of EnvironmentalY-12Oak I1

  7. Master Control of Multiple Air Compressors 

    E-Print Network [OSTI]

    Petzold, M. A.

    1983-01-01

    of air compressors in the most efficient manner for any air demand. This system can be further enhanced by the addition of a remote set point signal based on air-flow. This signal is calibrated to reduce the set-point during periods of low demand when...

  8. Oak Poisoning in Livestock. 

    E-Print Network [OSTI]

    Dollahite, J. W.; Housholder, G. T.; Camp, B. J.

    1966-01-01

    leaves. All developed severe signs of poisoning an~l fiv: died (Figure 2). Six other calves were fed oitk ir! quantities averaging 32.1 percent of their body \\vc.i~h. and 1.8 pounds daily of supplementary feed. Fivc . these developed signs of oak...

  9. Dynamically balanced, hydraulically driven compressor/pump apparatus for resonant free piston Stirling engines

    DOE Patents [OSTI]

    Corey, John A. (North Troy, NY)

    1984-05-29

    A compressor, pump, or alternator apparatus is designed for use with a resonant free piston Stirling engine so as to isolate apparatus fluid from the periodically pressurized working fluid of the Stirling engine. The apparatus housing has a first side closed by a power coupling flexible diaphragm (the engine working member) and a second side closed by a flexible diaphragm gas spring. A reciprocally movable piston is disposed in a transverse cylinder in the housing and moves substantially at right angles relative to the flexible diaphragms. An incompressible fluid fills the housing which is divided into two separate chambers by suitable ports. One chamber provides fluid coupling between the power diaphragm of the RFPSE and the piston and the second chamber provides fluid coupling between the gas spring diaphragm and the opposite side of the piston. The working members of a gas compressor, pump, or alternator are driven by the piston. Sealing and wearing parts of the apparatus are mounted at the external ends of the transverse cylinder in a double acting arrangement for accessibility. An annular counterweight is mounted externally of the reciprocally movable piston and is driven by incompressible fluid coupling in a direction opposite to the piston so as to damp out transverse vibrations.

  10. Combined cold compressor/ejector helium refrigerator

    DOE Patents [OSTI]

    Brown, D.P.

    1984-06-05

    A refrigeration apparatus having an ejector operatively connected with a cold compressor to form a two-stage pumping system. This pumping system is used to lower the pressure, and thereby the temperature of a bath of boiling refrigerant (helium). The apparatus as thus arranged and operated has substantially improved operating efficiency when compared to other processes or arrangements for achieving a similar low pressure.

  11. Viscous throughflow modeling for multistage compressor design

    SciTech Connect (OSTI)

    Howard, M.A.; Gallimore, S.J. )

    1993-04-01

    An existing throughflow method for axial compressors, which accounts for the effects of spanwise mixing using a turbulent diffusion model, has been extended to include the viscous shear force on the endwall. The use of a shear force, consistent with a no-slip condition, on the annulus walls in the throughflow calculations allows realistic predictions of the velocity and flow angle profiles near the endwalls. The annulus wall boundary layers are therefore incorporated directly into the throughflow prediction. This eliminates the need for empirical blockage factors or independent annulus boundary layer calculations. The axisymmetric prediction can be further refined by specifying realistic spanwise variations of loss coefficient and deviation to model the three-dimensional endwall effects. The resulting throughflow calculation gives realistic predictions of flow properties across the whole span of a compressor. This is confirmed by comparison with measured data from both low and high-speed multistage machines. The viscous throughflow method has been incorporated into an axial compressor design system. The method predicts the meridional velocity defects in the endwall region and consequently blading can be designed that allows for the increased incidence, and low dynamic head, near the annulus walls.

  12. METAL HYDRIDE HYDROGEN COMPRESSORS: A REVIEW

    SciTech Connect (OSTI)

    Bowman Jr, Robert C; Yartys, Dr. Volodymyr A.; Lototskyy, Dr. Michael V; Pollet, Dr. B.G.

    2014-01-01

    Metal hydride (MH) thermal sorption compression is an efficient and reliable method allowing a conversion of energy from heat into a compressed hydrogen gas. The most important component of such a thermal engine the metal hydride material itself should possess several material features in order to achieve an efficient performance in the hydrogen compression. Apart from the hydrogen storage characteristics important for every solid H storage material (e.g. gravimetric and volumetric efficiency of H storage, hydrogen sorption kinetics and effective thermal conductivity), the thermodynamics of the metal-hydrogen systems is of primary importance resulting in a temperature dependence of the absorption/desorption pressures). Several specific features should be optimized to govern the performance of the MH-compressors including synchronisation of the pressure plateaus for multi-stage compressors, reduction of slope of the isotherms and hysteresis, increase of cycling stability and life time, together with challenges in system design associated with volume expansion of the metal matrix during the hydrogenation. The present review summarises numerous papers and patent literature dealing with MH hydrogen compression technology. The review considers (a) fundamental aspects of materials development with a focus on structure and phase equilibria in the metal-hydrogen systems suitable for the hydrogen compression; and (b) applied aspects, including their consideration from the applied thermodynamic viewpoint, system design features and performances of the metal hydride compressors and major applications.

  13. IEMDC - In-Line Electric Motor Driven Compressor

    SciTech Connect (OSTI)

    Michael J. Crowley

    2004-03-31

    This report covers the fifth quarter (01/01/04 to 03/31/04) of the In-Line Electric Motor Driven Compressor (IEMDC) project. Design efforts on the IEMDC continued with compressor efforts focused on performing aerodynamic analyses. These analyses were conducted using computational fluid dynamics. Compressor efforts also entailed developing mechanical designs of components through the use of solid models and working on project deliverables. Electric motor efforts focused on the design of the magnetic bearing system, motor pressure housing, and the motor-compressor interface. The mechanical evaluation of the main interface from both the perspective of the compressor manufacturer and electric motor manufacturer indicates that an acceptable design has been achieved. All mechanical and aerodynamic design efforts have resulted in considerable progress being made towards the completion of the compressor and electric motor design and towards the successful completion of the IEMDC unit.

  14. Effect of Intake Air on Compressor Performance; Industrial Technologie...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    4 * August 2004 Industrial Technologies Program Suggested Actions * Inspect the entry to the compressor air intake pipe and ensure that it is free of contaminants. * Inspect the...

  15. New Compressor Concept Improves Efficiency and Operation Range

    Broader source: Energy.gov [DOE]

    Advanced turbocharger compressor design with active casing treatment and advanced mixed flow turbine design provided improved performance and efficiency over the base turbocharger

  16. Critical speed measurements in the Tevatron cold compressors

    SciTech Connect (OSTI)

    DeGraff, B.; Bossert, R.; Martinez, A.; Soyars, W.M.; /Fermilab

    2006-01-01

    The Fermilab Tevatron cryogenic system utilizes high-speed centrifugal cold compressors, manufactured by Ishikawajima-Harima Heavy Industries Co. Ltd. (IHI), for high energy operations. Nominal operating range for these compressors is 43,000 to 85,000 rpm. Past foil bearing failures prompted investigation to determine if critical speeds for operating compressors fall within operating range. Data acquisition hardware and software settings will be discussed for measuring liftoff, first critical and second critical speeds. Several tests provided comparisons between an optical displacement probe and accelerometer measurements. Vibration data and analysis of the 20 Tevatron ring cold compressors will be presented.

  17. The unstable behavior of low and high-speed compressors

    SciTech Connect (OSTI)

    Day, I.J. . Whittle Lab.); Freeman, C. )

    1994-04-01

    By far the greater part of the understanding about stall and surge in axial compressors comes from work on low-speed laboratory machines. As a general rule, these machines do not model the compressibility effects present in high-speed compressors and therefore doubt has always existed about the application of low-speed results to high-speed machines. In recent years interest in active control has led to a number of studies of compressor stability in engine-type compressors. The instrumentation used in these experiments has been sufficiently detailed that, for the first time, adequate data are available to make direct comparisons between high-speed and low-speed compressors. This paper presents new data from an eight-stage fixed geometry engine compressor and compares then with low-speed laboratory data. The results show remarkable similarities in both the stalling and surging behavior of the two machines, particularly when the engine compressor is run at intermediate speeds. The engine results also show that, as in the laboratory tests, surge is precipitated by the onset of rotating stall. This is true even at very high speeds where it had previously been thought that surge might be the result of a blast wave moving through the compressor. This paper therefore contains new information about high-speed compressors and confirms that low-speed testing is an effective means of obtaining insight into the behavior of high-speed machines.

  18. Independent Oversight Inspection, Oak Ridge National Laboratory...

    Energy Savers [EERE]

    Inspection, Oak Ridge National Laboratory - October 2008 Independent Oversight Inspection, Oak Ridge National Laboratory - October 2008 October 2008 Inspection of Nuclear Safety at...

  19. Oak Ridge Site Specific

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite Specific adviSORy

  20. Oak Ridge O

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access to scienceSpeeding accessScientificandThe1Oak Ridge NationalO ffice

  1. Oak Ridge Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access to scienceSpeeding accessScientificandThe1Oak Ridge NationalO

  2. Oak Ridge Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access to scienceSpeeding accessScientificandThe1Oak Ridge NationalOP.O.

  3. Oak Ridge Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access to scienceSpeeding accessScientificandThe1Oak Ridge

  4. Oak Ridge Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access to scienceSpeeding accessScientificandThe1Oak RidgeOctober 1, 2008

  5. Oak Ridge Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access to scienceSpeeding accessScientificandThe1Oak RidgeOctober 1,

  6. Oak Ridge Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access to scienceSpeeding accessScientificandThe1Oak RidgeOctober 1,22,

  7. FEASIBILITY OF SOLAR-FIRED, COMPRESSOR-ASSISTED

    E-Print Network [OSTI]

    FEASIBILITY OF SOLAR-FIRED, COMPRESSOR-ASSISTED ABSORPTION CHILLERS Prepared For: California Energy REPORT (FAR) FEASIBILITY OF SOLAR FIRED, COMPRESSOR ASSISTED ABSORPTION CHILLERS EISG AWARDEE Bergquam.csus.edu Principal Investigator: James Bergquam AUTHOR EISG Program Administrator Grant #: 99-15 Grant Funding: $75

  8. POWER CHARACTERISTICS OF INDUSTRIAL AIR COMPRESSORS Chris Schmidt

    E-Print Network [OSTI]

    Kissock, Kelly

    POWER CHARACTERISTICS OF INDUSTRIAL AIR COMPRESSORS Chris Schmidt Graduate Assistant / Project of Mechanical and Aerospace Engineering University of Dayton Dayton, Ohio ABSTRACT The power draw to energy input, which we call the average operating efficiency, based on input power to the compressor

  9. Introducing Back-up to Active Compressor Surge Control System

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    to compressor blades and bearings. Most industrial compressors are equipped with a surge avoidance system by recycling flow from downstream to upstream when the operating point reach a surge control line Jager This work was supported Siemens Oil and Gas Solutions Offshore through the Siemens

  10. Modeling and Control of Surge and Rotating Stall in Compressors

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    Modeling and Control of Surge and Rotating Stall in Compressors Dr.ing. thesis Jan Tommy Gravdahl varying disturbances in mass ow and pressure. A novel model for an axial compression system with non-constant compressor speed is derived by extending the Moore-Greitzer model. Rotating stall and surge is studied

  11. Small core axial compressors for high efficiency jet aircraft

    E-Print Network [OSTI]

    DiOrio, Austin Graf

    2012-01-01

    This thesis quantifies mechanisms that limit efficiency in small core axial compressors, defined here as compressor exit corrected flow between 1.5 and 3.0 lbm/s. The first part of the thesis describes why a small engine ...

  12. U.S. Department of Energy, Oak Ridge Office and URS/CH2M Oak...

    Office of Environmental Management (EM)

    Energy, Oak Ridge Office and URSCH2M Oak Ridge, LLC (UCOR) East Tennessee Technology Park (ETTP) Contract Partnering Agreement U.S. Department of Energy, Oak Ridge Office and URS...

  13. Drive actuation in active control of centrifugal compressors Jan Tommy Gravdahl and Olav Egeland

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    Pipeline compressor map for natural gas (=1.3) System trajectory Throttle line Surge line Compressor map does not cross this line. Usually a recycle valve around the compressor is used as actuation. A simulation of active surge control on a industrial size nat- ural gas pipeline compressor using drive torque

  14. Oak Ridge Reservation Annual Site

    E-Print Network [OSTI]

    Pennycook, Steve

    Complex Oak Ridge National Laboratory East Tennessee Technology Park Electronic publisher Editors Graphic's Vision for the East Tennessee Technology Park Mission under Contract DE-SC-0004645 #12;#12;iii Contents................................................................................................1-2 1.3.2 Climate

  15. Surge recovery techniques for the Tevatron cold compressors

    SciTech Connect (OSTI)

    Martinez, A.; Klebaner, A.L.; Makara, J.N.; Theilacker, J.C.; /Fermilab

    2006-01-01

    The Fermilab Tevatron cryogenic system utilizes high-speed centrifugal cold compressors, made by Ishikawajima-Harima Heavy Industries Co. Ltd. (IHI), for high-energy operations [1]. The compressor is designed to pump 60 g/s of 3.6 K saturated helium vapor at a pressure ratio of 2.8, with an off-design range of 40 to 70 g/s and operating speeds between 40 and 95 krpm. Since initial commissioning in 1993, Tevatron transient conditions such as quench recovery have led to multiple-location machine trips as a result of the cold compressors entering the surge regime. Historically, compressors operating at lower inlet pressures and higher speeds have been especially susceptible to these machine trips and it was not uncommon to have multiple compressor trips during large multiple-house quenches. In order to cope with these events and limit accelerator down time, surge recovery techniques have been implemented in an attempt to prevent the compressors from tripping once the machine entered this surge regime. This paper discusses the different methods of surge recovery that have been employed. Data from tests performed at the Cryogenic Test Facility at Fermilab as well as actual Tevatron operational data were utilized. In order to aid in the determination of the surge region, a full mapping study was undertaken to characterize the entire pressure field of the cold compressor. These techniques were then implemented and tested at several locations in the Tevatron with some success.

  16. Pressure field study of the Tevatron cold compressors

    SciTech Connect (OSTI)

    Klebaner, A.L.; Martinez, A.; Soyars, W.M.; Theilacker, J.C.; /Fermilab

    2003-01-01

    The Fermilab Tevatron cryogenic system utilizes high-speed centrifugal cold compressors, manufactured by Ishikawajima-Harima Heavy Industries Co. Ltd. (IHI), for high-energy operations [1]. The compressor is designed to pump 60 g/sec of 3.6 K saturated helium vapor at a pressure ratio of 2.8, with an off-design range of 40 to 70 g/sec. Operating speeds are between 40 and 95 krpm, with a speed of 80 krpm at the design point. Different heat loads and magnet quench performance of each of the twenty-four satellite refrigerators dictates different process pressure and flow rates of the cold compressors. Reducing the process flow rate can cause the centrifugal cold compressor to stop pumping and subsequently surge. Tests have been conducted at the Cryogenic Test Facility at Fermilab to map the pressure field and appropriate efficiency of the IHI hydrodynamic cold compressor. The information allows tuning of each of the twenty-four Tevatron satellite refrigerators to avoid cold compressor operation near the surge and choke lines. A new impeller has also been tested. The Tevatron cold compressor pressure field and efficiency data with the new impeller are presented in this paper.

  17. Oak Ridge Associated Universities

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield Municipal Gas &SCE-SessionsSouthReport for the Weldon Spring,7=cr5rnP 7694 i+lJNewS e TAugust 4,the

  18. Simultaneous Robust Design and Tolerancing of Compressor Blades

    E-Print Network [OSTI]

    Wang, Qiqi

    The manufacturing processes used to create compressor blades inevitably introduce geometric variability to the blade surface. In addition to increasing the performance variability, it has been observed that introducing ...

  19. Characterization of unsteady flow processes in a centrifugal compressor stage

    E-Print Network [OSTI]

    Gould, Kenneth A. (Kenneth Arthur)

    2006-01-01

    Numerical experiments have been implemented to characterize the unsteady loading on the rotating impeller blades in a modem centrifugal compressor. These consist of unsteady Reynolds-averaged Navier Stokes simulations of ...

  20. Forced response predictions in modern centrifugal compressor design

    E-Print Network [OSTI]

    Smythe, Caitlin J. (Caitlin Jeanne)

    2005-01-01

    A computational interrogation of the time-averaged and time-unsteady flow fields of two centrifugal compressors of nearly identical design (the enhanced, which encountered aeromechanical difficulty, and production, which ...

  1. Return channel loss reduction in multi-stage centrifugal compressors

    E-Print Network [OSTI]

    Aubry, Anne-Raphaëlle

    2012-01-01

    This thesis presents concepts for improving the performance of return channels in multi-stage centrifugal compressors. Geometries have been developed to reduce both separation and viscous losses. A number of different ...

  2. Multi-parameter control for centrifugal compressor performance optimization

    E-Print Network [OSTI]

    Mannai, Sébastien (Sébastien Karim)

    2014-01-01

    The potential performance benefit of actuating inlet guide vane (IGV) angle, variable diffuser vane (VDV) angle and impeller speed to implement a multi-parameter control on a centrifugal compressor system is assessed. The ...

  3. New Twin Screw Compressor Design by Deviation Function Method

    E-Print Network [OSTI]

    Huang, Chih-Yung

    2015-01-01

    Gear Geometry," Transaction of ASME: Journal of Mechanical Design,Gear Pump," Trans. ASME Journal of Mechanisms, and Transmissions, and Automation in Design,design is an oil-free compressor and is driven by a pair of timing gears.

  4. Energy conversion using thermal transpiration : optimization of a Knudsen compressor

    E-Print Network [OSTI]

    Klein, Toby A. (Toby Anna)

    2012-01-01

    Knudsen compressors are devices without any moving parts that use the nanoscale phenomenon of thermal transpiration to pump or compress a gas. Thermal transpiration takes place when a gas is in contact with a solid boundary ...

  5. Active control of tip clearance flow in axial compressors

    E-Print Network [OSTI]

    Bae, Jinwoo W

    2001-01-01

    Control of compressor tip clearance flows is explored in a linear cascade using three types of fluidic actuators; Normal Synthetic Jet (NSJ; unsteady jet normal to the mean flow with zero net mass flux), Directed Synthetic ...

  6. Non-intrusive fault detection in reciprocating compressors

    E-Print Network [OSTI]

    Schantz, Christopher James

    2011-01-01

    This thesis presents a set of techniques for non-intrusive sensing and fault detection in reciprocating compressors driven by induction motors. The procedures developed here are "non-intrusive" because they rely only on ...

  7. Development Of A Centrifugal Hydrogen Pipeline Gas Compressor

    SciTech Connect (OSTI)

    Di Bella, Francis A.

    2015-04-16

    Concepts NREC (CN) has completed a Department of Energy (DOE) sponsored project to analyze, design, and fabricate a pipeline capacity hydrogen compressor. The pipeline compressor is a critical component in the DOE strategy to provide sufficient quantities of hydrogen to support the expected shift in transportation fuels from liquid and natural gas to hydrogen. The hydrogen would be generated by renewable energy (solar, wind, and perhaps even tidal or ocean), and would be electrolyzed from water. The hydrogen would then be transported to the population centers in the U.S., where fuel-cell vehicles are expected to become popular and necessary to relieve dependency on fossil fuels. The specifications for the required pipeline hydrogen compressor indicates a need for a small package that is efficient, less costly, and more reliable than what is available in the form of a multi-cylinder, reciprocating (positive displacement) compressor for compressing hydrogen in the gas industry.

  8. K-311-1/K-310-3 Purge Cascade Process Description, Oak Ridge Environmental Management Accelerated Cleanup Project, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Shoemaker J.E.

    2009-05-13

    K-311-1 was constructed along with the rest of the K-25 Building in the 1943-1945 timeframe. K-311-1 was equipped with Size 3 converters and Size 38 Allis Chalmers{trademark} single-stage centrifugal compressors driven by 3600 rpm electric motors, and the unit operated as the 'bottom' unit flow-wise in K-25. The depleted flow from the bottom stage in K-311-1 passed through booster compressors and flowed to the K-601 Building where the depleted or 'tails' material was removed. In 1948, after the K-27 Building was completed, the decision was made to operate K-27 and K-25 in series rather than operate the two buildings as separate entities. To facilitate this operation, concrete bases were poured and two sets of booster compressors were installed in the extreme West end of the K-311-1 cell floor. These compressors were enclosed in heated housings and consisted of Size 38 compressors. One pair was to boost the 'B' flow between K-25 and K-27, and one pair was to boost the 'A' flow between the buildings. Each station operated with one compressor on-stream and the other in standby. (Reference 9) Each station also was equipped with a Size 2 after-cooler located in the discharge stream downstream of the junction of the onstream and standby compressors. Additional gaseous diffusion capacity was added at Oak Ridge as K-29, K-31, and K-33 were constructed and placed in service in the early 1950s. As a result of the additional process equipment added by these buildings, in-leakage of light gases to the cascade including light gases introduced into the cascade as a result of purging operations threatened to exceed the capacity of the existing K-312 Purge Cascade facilities in the K-25 Building. As a result, in 1954 K-311-1 was converted to a side purge cascade to remove light gases from the process gas stream as the stream entered K-25 from K-27. Low molecular weight gas in-leakage in K-33, K-31, K-29, and K-27 was removed by the K-311-1 Side Purge Facility and a relatively pure stream of UF6 then passed from K-311-1 into the upstream cells in K-25. In-leakage of light gases in the K-25 Building continued to be removed by the K-312 Purge Facilities. K-311-1 operated as a Side Purge Cascade from 1954 until the K-25 Building was shut down in 1964; at that time K-311-1 became the Oak Ridge Gaseous Diffusion Plant (ORGDP) Top (and only) Purge Cascade. The adjacent K-310-3 Unit was operated along with K-311-1 as the top purge cascade and K-310-2 was also operated at times to supplement cells in the K311-1/K-310-3 Purge Cascade. K-311-1 was shut down on February 14, 1977, after the newer, larger capacity K-402-9 Purge Cascade was placed in operation. K-310-3 continued to operate until the K-402-8 Coolant Removal Unit was placed in service, and K-310-3 was shut down on March 14, 1978. Since the K-311-1 and K-310-3 units continued to operate after K-25 shutdown, removal of equipment such as valves and piping for other projects did not occur in this area. As a result, these two units have not been exposed to atmospheric wet air over the years as much of the remainder of K-25 has been exposed. Any deposits or residual gases contained in K-311-1 or K-310-3 are not likely to be fully hydrolyzed.

  9. Five more spring nature walks planned on Oak Ridge Reservation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    is scheduled from 7 until 9 p.m. Saturday, April 4, and will be concentrated in the ponds around East Tennessee Technology Park. Wade Gefellers and Kitty McCracken of ORNL's...

  10. Independent Oversight Review, Oak Ridge Transuranic Waste Processing...

    Energy Savers [EERE]

    Independent Oversight Review, Oak Ridge Transuranic Waste Processing Facility - December 2013 Independent Oversight Review, Oak Ridge Transuranic Waste Processing Facility -...

  11. Control optimization of the cryoplant warm compressor station for EAST

    SciTech Connect (OSTI)

    Zhuang, M.; Hu, L. B.; Zhou, Z. W.; Xia, G. H. [Cryogenic Engineering Division, Institute of Plasma Physics Chinese Academy of Sciences, P.O.Box 1126,Shushanhu Road 350, Hefei, Anhui 230031 (China)

    2014-01-29

    The cryogenic control system for EAST (Experimental Advanced Superconducting Tokamak) was designed based on DeltaV DCS of Emerson Corporation. The automatic control of the cryoplant warm compressors has been implemented. However, with ever-degrading performance of critical equipment, the cryoplant operation in the partial design conditions makes the control system fluctuate and unstable. In this paper, the warm compressor control system was optimized to eliminate the pressure oscillation based on the expert PID theory.

  12. Hyper dispersion pulse compressor for chirped pulse amplification systems

    DOE Patents [OSTI]

    Barty, Christopher P. J. (Hayward, CA)

    2011-11-29

    A grating pulse compressor configuration is introduced for increasing the optical dispersion for a given footprint and to make practical the application for chirped pulse amplification (CPA) to quasi-narrow bandwidth materials, such as Nd:YAG. The grating configurations often use cascaded pairs of gratings to increase angular dispersion an order of magnitude or more. Increased angular dispersion allows for decreased grating separation and a smaller compressor footprint.

  13. Development of Inexpensive Turbo Compressor/Expanders for Industrial Use 

    E-Print Network [OSTI]

    Jacox, J. W.

    1991-01-01

    designed, coordinated and partially performed by NUCON. The turbocharger consists of a radial inflow turbine and a centrifugal compressor mounted on a common shaft supported on oil lubricated floating bushing type journal bearings. The axial thrust.... The TCE performance was not as serious a problem, except to achieve both high and matched efficiency for the expander AND compressor when operated in the reverse mode. Locating a cost effective mass produced TCE was the most difficult of the three...

  14. ADVANCED COMPRESSOR ENGINE CONTROLS TO ENHANCE OPERATION, RELIABILITY AND INTEGRITY

    SciTech Connect (OSTI)

    Gary D. Bourn; Jess W. Gingrich; Jack A. Smith

    2004-03-01

    This document is the final report for the ''Advanced Compressor Engine Controls to Enhance Operation, Reliability, and Integrity'' project. SwRI conducted this project for DOE in conjunction with Cooper Compression, under DOE contract number DE-FC26-03NT41859. This report addresses an investigation of engine controls for integral compressor engines and the development of control strategies that implement closed-loop NOX emissions feedback.

  15. An analytical model of axial compressor off-design performance

    SciTech Connect (OSTI)

    Camp, T.R.; Horlock, J.H. . Whittle Lab.)

    1994-07-01

    An analysis is presented of the off-design performance of multistage axial-flow compressors. It is based on an analytical solution, valid for small perturbations in operating conditions from the design point, and provides an insight into the effects of choices made during the compressor design process on performance and off-design stage matching. It is shown that the mean design value of stage loading coefficient ([psi] = [Delta]h[sub 0]/U[sup 2]) has a dominant effect on off-design performance, whereas the stage-wise distribution of stage loading coefficient and the design value of flow coefficient have little influence. The powerful effects of variable stator vanes on stage-matching are also demonstrated and these results are shown to agree well with previous work. The slope of the working line of a gas turbine engine, overlaid on overall compressor characteristics, is shown to have a strong effect on the off-design stage-matching through the compressor. The model is also used to analyze design changes to the compressor geometry and to show how errors in estimates of annulus blockage, decided during the design process, have less effect on compressor performance than has previously been thought.

  16. Effects of Shade on Blue Oak and Coast Live Oak Regeneration in California Annual Grasslands1

    E-Print Network [OSTI]

    Effects of Shade on Blue Oak and Coast Live Oak Regeneration in California Annual Grasslands1 manipulation. A split-plot, multifactorial experi ment was designed to test whether blue oak (Quercus douglasii herbaceous vegetation was not manipulated. Even under conditions of prolonged, severe drought, blue oaks

  17. Downhole steam generator having a downhole oxidant compressor

    DOE Patents [OSTI]

    Fox, Ronald L. (Albuquerque, NM)

    1983-01-01

    Apparatus and method for generation of steam in a borehole for penetration into an earth formation wherein a downhole oxidant compressor is used to compress relatively low pressure (atmospheric) oxidant, such as air, to a relatively high pressure prior to mixing with fuel for combustion. The multi-stage compressor receives motive power through a shaft driven by a gas turbine powered by the hot expanding combustion gases. The main flow of compressed oxidant passes through a velocity increasing nozzle formed by a reduced central section of the compressor housing. An oxidant bypass feedpipe leading to peripheral oxidant injection nozzles of the combustion chamber are also provided. The downhole compressor allows effective steam generation in deep wells without need for high pressure surface compressors. Feedback preheater means are provided for preheating fuel in a preheat chamber. Preheating of the water occurs in both a water feed line running from aboveground and in a countercurrent water flow channel surrounding the combustor assembly. The countercurrent water flow channels advantageously serve to cool the combustion chamber wall. The water is injected through slotted inlets along the combustion chamber wall to provide an unstable boundary layer and stripping of the water from the wall for efficient steam generation. Pressure responsive doors are provided at the steam outlet for closing and sealing the combustion chamber from entry of reservoir fluids in the event of a flameout.

  18. Development of an Electrochemical Separator and Compressor

    SciTech Connect (OSTI)

    Trent Molter

    2011-04-28

    Global conversion to sustainable energy is likely to result in a hydrogen-based economy that supports U.S. energy security objectives while simultaneously avoiding harmful carbon emissions. A key hurdle to successful implementation of a hydrogen economy is the low-cost generation, storage, and distribution of hydrogen. One of the most difficult requirements of this transformation is achieving economical, high density hydrogen storage in passenger vehicles. Transportation applications may require compression and storage of high purity hydrogen up to 12,000 psi. Hydrogen production choices range from centralized low-pressure generation of relatively impure gas in large quantities from steam-methane reformer plants to distributed generation of hydrogen under moderate pressure using water electrolysis. The Electrochemical Hydrogen Separator + Compressor (EHS+C) technology separates hydrogen from impurities and then compresses it to high pressure without any moving parts. The Phase I effort resulted in the construction and demonstration of a laboratory-scale hardware that can separate and compress hydrogen from reformate streams. The completion of Phase I has demonstrated at the laboratory scale the efficient separation and compression of hydrogen in a cost effective manner. This was achieved by optimizing the design of the Electrochemical Hydrogen Compression (EHC) cell hardware and verified by parametric testing in single cell hardware. A broad range of commercial applications exist for reclamation of hydrogen. One use this technology would be in combination with commercial fuel cells resulting in a source of clean power, heat, and compressed hydrogen. Other applications include the reclamation of hydrogen from power plants and other industrial equipment where it is used for cooling, recovery of process hydrogen from heat treating processes, and semiconductor fabrication lines. Hydrogen can also be recovered from reformate streams and cryogenic boil-offs using this technology.

  19. Design and operation of a counter-rotating aspirated compressor blowdown test facility

    E-Print Network [OSTI]

    Parker, David V. (David Vickery)

    2005-01-01

    A unique counter-rotating aspirated compressor was tested in a blowdown facility at the Gas Turbine Laboratory at MIT. The facility expanded on experience from previous blowdown turbine and blowdown compressor experiments. ...

  20. Application of a design optimization strategy to multi-stage compressor matching

    E-Print Network [OSTI]

    Bert, Jérôme

    2006-01-01

    A major challenge in the design of multi-stage compressors is the matching of stages to enable stable operation over a large range of mass flows and operating conditions. Particularly in turbofan low-pressure compressors, ...

  1. Optimal dimensionless design and analysis of jet ejectors as compressors and thrust augmenters 

    E-Print Network [OSTI]

    Mohan, Ganesh

    2006-08-16

    A jet ejector may be used as a compressor or to enhance thrust of watercraft or aircraft. Optimization of jet ejectors as compressors and thrust augmenters was conducted using the software GAMBIT (Computer Aided Engineering (CAE) tool for geometry...

  2. Turbo-alternator-compressor design for supercritical high density working fluids

    DOE Patents [OSTI]

    Wright, Steven A.; Fuller, Robert L.

    2013-03-19

    Techniques for generating power are provided. Such techniques involve a thermodynamic system including a housing, a turbine positioned in a turbine cavity of the housing, a compressor positioned in a compressor cavity of the housing, and an alternator positioned in a rotor cavity between the turbine and compressor cavities. The compressor has a high-pressure face facing an inlet of the compressor cavity and a low-pressure face on an opposite side thereof. The alternator has a rotor shaft operatively connected to the turbine and compressor, and is supported in the housing by bearings. Ridges extending from the low-pressure face of the compressor may be provided for balancing thrust across the compressor. Seals may be positioned about the alternator for selectively leaking fluid into the rotor cavity to reduce the temperature therein.

  3. Oak Leaf Roller and Springtime Defoliation of Live Oak Trees 

    E-Print Network [OSTI]

    Drees, Bastiaan M.

    2004-03-26

    . Two such caterpillars are the oak leaf roller, Archips semiferana (Walker) (Lepi- doptera: Tortricidae), and an associated species, Sparga- nothis pettitana. These insects occur throughout Texas but are most destructive in the Hill Country and South... broad- rimmed hats and long-sleeved shirts while out- doors may also help prevent contact with these insects. Damage When a tree is defoliated during the growing season, it becomes stressed and occasionally seri- ous damage can occur. Green leaves...

  4. Investigation of Non-synchronous Vibration Mechanism for a High Speed Axial Compressor Using Delayed DES

    E-Print Network [OSTI]

    Zha, Gecheng

    Investigation of Non-synchronous Vibration Mechanism for a High Speed Axial Compressor Using compressor. DDES is a hybrid model for turbulence simulation, which uses RANS model within the wall boundary a torsion moment causing NSV. 1 Introduction Non-synchronous vibration of axial fan/compressor is a non

  5. A Moore-Greitzer axial compressor model with spool Jan Tommy Gravdahl and Olav Egeland

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    A Moore-Greitzer axial compressor model with spool dynamics. Jan Tommy Gravdahl and Olav Egeland applies to centrifugal compressors. It seems that the modeling and control of an axial com- pression) Table 1: Development in compressor stall/surge- control. A=Axial, C=Centrifugal, M=Modeling, C

  6. Test results on a supercharged compressor for commercial refrigeration

    SciTech Connect (OSTI)

    Andrews, J.W.; Butcher, T.A.; Wilhelm, W.G. )

    1989-01-01

    This paper reports on a project whose objective was to quantify the technical benefits of using refrigerant R-502 in a supercharged reciprocating compressor for commercial refrigeration applications. The supercharged compressor concept used a special heat exchanger that subcools the major portion of the liquid refrigerant leaving the condenser. This subcooling is achieved by flashing the remaining portion of the condensed liquid through an expansion valve, thereby cooling it, and using it to absorb heat from the rest of the refrigerant. This supercharged stream is then fed to the cylinders through ports in the cylinder walls that are uncovered when the piston reaches bottom dead center.

  7. High-current, low-energy synchrotrons and compressor rings

    SciTech Connect (OSTI)

    Kustom, R.L.

    1984-05-01

    The primary application of high-current, low-energy synchrotrons and linac compressor rings is as proton drivers for pulsed-spallation neutron sources. They operate in the range of 500 to 1500 MeV with extracted beam repetition rates between 12 to 100 Hz. The time-averaged currents on target are a few tens of microamperes today, soon will be a few thousand in the future. The characteristics for the accelerators and compressor rings, their limitations, and existing and proposed major facilities are described. 22 references, 5 figures, 6 tables.

  8. Oak Ridge National Laboratory Review

    SciTech Connect (OSTI)

    Krause, C.; Pearce, J.; Zucker, A.

    1992-01-01

    This report presents brief descriptions of the following programs at Oak Ridge National Laboratory: The effects of pollution and climate change on forests; automation to improve the safety and efficiency of rearming battle tanks; new technologies for DNA sequencing; ORNL probes the human genome; ORNL as a supercomputer research center; paving the way to superconcrete made with polystyrene; a new look at supercritical water used in waste treatment; and small mammals as environmental monitors.

  9. EA-1044: Melton Valley Storage Tanks Capacity Increase Project- Oak Ridge National Laboratory, Oak Ridge, Tennessee

    Broader source: Energy.gov [DOE]

    This EA evaluates the environmental impacts of the proposal to construct and maintain additional storage capacity at the U.S. Department of Energy's Oak Ridge National Laboratory, Oak Ridge,...

  10. The Oak Ridge National Laboratory automobile heat pump model: User`s guide

    SciTech Connect (OSTI)

    Kyle, D.M.

    1993-05-01

    A computer program has been developed to predict the steady-state performance of vapor compression automobile air conditioners and heat pumps. The code is based on the residential heat pump model developed at Oak Ridge National Laboratory. Most calculations are based on fundamental physical principles, in conjunction with generalized correlations available in the research literature. Automobile air conditioning components that can be specified as inputs to the program include open and hermetic compressors; finned tube condensers; finned tube and plate-fin style evaporators; thermal expansion valve, capillary tube and short tube expansion devices; refrigerant mass; evaporator pressure regulator; and all interconnecting tubing. The program can be used with a variety of refrigerants, including R134a. Methodologies are discussed for using the model as a tool for designing all new systems or, alternatively, as a tool for simulating a known system for a variety of operating conditions.

  11. Oak Ridge Reservation Environmental Monitoring Program 6-1 6. Oak Ridge Reservation Environmental

    E-Print Network [OSTI]

    Pennycook, Steve

    monitoring program are analyzed to assess the environmental impact of DOE operations on the entire1 Oak Ridge Reservation Environmental Monitoring Program 6-1 6. Oak Ridge Reservation Environmental Monitoring Program In addition to environmental monitoring conducted at the three major Oak Ridge DOE

  12. Compressor Selection and Equipment Sizing for Cold Climate Heat Pumps

    SciTech Connect (OSTI)

    Shen, Bo [ORNL] [ORNL; Abdelaziz, Omar [ORNL] [ORNL; Rice, C Keith [ORNL] [ORNL

    2014-01-01

    In order to limit heating capacity degradation at -25 C (-13 F) ambient to 25%, compared to the nominal rating point capacity at 8.3 C (47 F), an extensive array of design and sizing options were investigated, based on fundamental equipment system modeling and building energy simulation. Sixteen equipment design options were evaluated in one commercial building and one residential building, respectively in seven cities. The energy simulation results were compared to three baseline cases: 100% electric resistance heating, a 9.6 HSPF single-speed heat pump unit, and 90% AFUE gas heating system. The general recommendation is that variable-speed compressors and tandem compressors, sized such that their rated heating capacity at a low speed matching the building design cooling load, are able to achieve the capacity goal at low ambient temperatures by over-speeding, for example, a home with a 3.0 ton design cooling load, a tandem heat pump could meet this cooling load running a single compressor, while running both compressors to meet heating load at low ambient temperatures in a cold climate. Energy savings and electric resistance heat reductions vary with building types, energy codes and climate zones. Oversizing a heat pump can result in larger energy saving in a less energy efficient building and colder regions due to reducing electric resistance heating. However, in a more energy-efficient building or for buildings in warmer climates, one has to consider balance between reduction of resistance heat and addition of cyclic loss.

  13. Scroll compressor modelling for heat pumps using hydrocarbons as refrigerants

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Scroll compressor modelling for heat pumps using hydrocarbons as refrigerants Paul BYRNE and to install heat pumps in unoccupied spaces. Nevertheless manufacturers keep working on components for hydrocarbons. In the frame of a research project on heat pumps for simultaneous heating and cooling, an R407C

  14. Speed and surge control for a low order centrifugal compressor model Jan Tommy Gravdahl and Olav Egeland

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    a model for axial compressor mass ow and pressure rise was presented. In 13] it was shown that the modelSpeed and surge control for a low order centrifugal compressor model Jan Tommy Gravdahl and Olav of the compressor. First a low order centrifugal compressor model is presented where the states are mass ow

  15. 83-9E9-TOPIC-P3 Unrestricted DOMslon ManagerHIGH-EFFICIENCY DUAL-STROKE COMPRESSOR

    E-Print Network [OSTI]

    Oak Ridge National Laboratory

    , two-capacity,.three cylinder, reciprocating piston, hermetic compressor for the advanced electric heat-pump

  16. Enterprise Assessments, Oak Ridge National Laboratory Irradiated...

    Broader source: Energy.gov (indexed) [DOE]

    of the Safety-Significant Ventilation Systems at the Irradiated Fuels Examination Laboratory Operated by UT-Battelle for the Oak Ridge National Laboratory Office of Science The...

  17. Site characterization report for the Old Hydrofracture Facility at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    NONE

    1995-01-01

    Several Old Hydrofracture Facility (OHF) structures (i.e., Building 7852, the bulk storage bins, the pump house, water tank T-5, and pump P-3) are surplus facilities at Oak Ridge National Laboratory (ORNL) slated for decontamination and decommissioning (D and D). OHF was constructed in 1963 to allow experimentation and operations with an integrated solids storage, handling, mixing, and grout injection facility. It was shut down in 1980 and transferred to ORNL`s Surveillance and Maintenance Program. The hydrofracture process was a unique disposal method that involved injecting waste materials mixed with grout and additives under pumping pressures of 2,000 psi or greater into a deep, low-permeability shale formation. The injected slurry spread along fractures and bedding planes for hundreds of feet from the injection points, forming thin grout sheets (often less than 1/8 in. thick). The grout ostensibly immobilized and solidified the liquid wastes. Site characterization activities were conducted in the winter and spring of 1994 to collect information necessary to plan the D and D of OHF structures. This site characterization report documents the results of the investigation of OHF D and D structures, presenting data from the field investigation and laboratory analyses in the form of a site description, as-built drawings, summary tables of radiological and chemical contaminant concentrations, and a waste volume estimate. 25 refs., 54 figs., 17 tabs.

  18. Blue oak seedling age influences growth and mortality

    E-Print Network [OSTI]

    Phillips, Ralph L.; McDougald, Neil K.; McCreary, Doug D.; Atwill, Edward R.

    2007-01-01

    1997b. Stand- level status of blue oak sapling recruitment1991. Soil water effects on blue oak seedling establishment.NK, Standiford RB, Frost WE. 1996. Blue oak seedlings may be

  19. Spring in Sacramento

    E-Print Network [OSTI]

    Fields, Wesley

    2005-01-01

    41 LETTERS Spring in Sacramento Wesley Fields, MD, FACEPIt is spring again in Sacramento. The fruit trees are inthe rivers that meet in Sacramento. Returning to the capitol

  20. IEMDC -IN-LINE ELECTRIC MOTOR DRIVEN COMPRESSOR

    SciTech Connect (OSTI)

    Michael J. Crowley; Prem N. Bansal; John E. Tessaro

    2004-01-01

    Dresser-Rand completed the preliminary aerodynamic flowpath of the volute and inlet design for the compressor section. This has resulted in considerable progress being made on the development of the compressor section and ultimately towards the successful integration of the IEMDC System design. Significant effort was put forth in the design of aerodynamic components which resulted in a design that meets the limits of aerodynamically induced radial forces previously established. Substantial effort has begun on the mechanical design of the compressor pressure containing case and other internal components. These efforts show progression towards the successful integration of a centrifugal compressor and variable speed electric motor ventilated by the process gas. All efforts continue to confirm the feasibility of the IEMDC system design. During the third quarter reporting period, the focus was to further refine the motor design and to ensure that the IEMDC rotor system supported on magnetic bearing is in compliance with the critical speed and vibration requirements of the API standards 617 and 541. Consequently specification to design magnetic bearings was developed and an RFQ to three magnetic bearing suppliers was issued. Considerable work was also performed to complete preliminary reports on some of the deliverable tasks under phase 1.0. These include specification for the VFD, RFQ for the magnetic bearings, and preliminary write-up for motor instrumentation and control schematic. In order to estimate motor efficiency at various operating points, plots of calculated motor losses, and motor cooling gas flow rates were also prepared. Preliminary evaluations of motor support concepts were performed via FEA to determine modal frequencies. Presentation was made at DOE Morgantown on August 12, 2003 to provide project status update. Preparations for the IEMDC motor-compressor presentation, at the GMRC conference in Salt Lake City to be held on October 5, 2003, were also started. Detailed calculations of cooling gas flow requirements for the motor and magnetic bearings, per several new operating points designated by DR, confirmed that the required gas flow was within the compressor design guidelines. Previous thrust load calculations had confirmed that the magnetic thrust bearing design load capacity of 6,000 lb. was sufficient to handle the net thrust load produced by the motor and compressor pressure loading. Thus the design data that has been generated, for the variable speed 10 MW 12,000 rpm motor, during the last three quarters, continue to confirm the feasibility of an efficient and robust motor design.

  1. CHP Research and Development - Presentation by Oak Ridge National...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research and Development - Presentation by Oak Ridge National Laboratory, June 2011 CHP Research and Development - Presentation by Oak Ridge National Laboratory, June 2011...

  2. Voluntary Protection Program Onsite Review, Oak Ridge Associated...

    Broader source: Energy.gov (indexed) [DOE]

    whether Oak Ridge Associated Universities Oak Ridge Institute for Science and Education is continuing to perform at a level deserving DOE-VPP Star recognition. The Team...

  3. PIA - Oak Ridge Institute for Science and Education Program Applicant...

    Energy Savers [EERE]

    Oak Ridge Institute for Science and Education Program Applicant and Participant Status System (APSS) PIA - Oak Ridge Institute for Science and Education Program Applicant and...

  4. Vehicle Technologies Office: 2008 Oak Ridge Transportation Technology...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Oak Ridge Transportation Technology Program Annual Report Vehicle Technologies Office: 2008 Oak Ridge Transportation Technology Program Annual Report ornlttpreportfy08.pdf More...

  5. DOE Awards $3 Million Contract to Oak Ridge Associated Universities...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Awards 3 Million Contract to Oak Ridge Associated Universities for Expert Review of Yucca Mountain Work DOE Awards 3 Million Contract to Oak Ridge Associated Universities for...

  6. Tennessee: Oak Ridge National Laboratory Optimizes Carbon Fiber...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tennessee: Oak Ridge National Laboratory Optimizes Carbon Fiber Production, Reduces Carbon Fiber Costs by 30% Tennessee: Oak Ridge National Laboratory Optimizes Carbon Fiber...

  7. DOE Oak Ridge Operations managers

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would like submit theCovalent Bonding Low-Cost2 DOE HQ F 1410.2 FormU.S. DOE Office ofObama09Oak

  8. Shady Oaks | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EIS Report UrlNM-bRenewableSMUDSectionalIndustrielsOaks Jump to:

  9. Oak Ridge | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on DeliciousMathematicsEnergyInterested Parties -DepartmentAvailable forSite |n t787ORDER NO.ORSSABOUOOakServicesOak

  10. Even more Oak Ridge transitions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would like submitKansasCommunitiesof Energy8) Wigner Home ·theEven more Oak Ridge

  11. Oak Ridge National Laboratory National Security Programs

    E-Print Network [OSTI]

    Security Challenges #12;3 OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY How Will Our Enemies and Homeland Security #12;OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY Nuclear Nonproliferation $27,050 Cleanup $7,481 Science $359M National Security $278M Energy $170M Cleanup $0.8M Total $1.08B

  12. Comprehensive Compressor Calorimeter Testing of Lower-GWP Alternative Refrigerants for Heat Pump and Medium Temperature Refrigeration Applications

    SciTech Connect (OSTI)

    Shrestha, Som S; Sharma, Vishaldeep; Abdelaziz, Omar

    2014-01-01

    In response to environmental concerns raised by the use of refrigerants with high Global Warming Potential (GWP), the Air-Conditioning, Heating, and Refrigeration Institute (AHRI) has launched an industry-wide cooperative research program, referred to as the Low-GWP Alternative Refrigerants Evaluation Program (AREP), to identify and evaluate promising alternative refrigerants for major product categories. This paper reports one of the Oak Ridge National Laboratory (ORNL) contributions to AREP. It compares performance of alternative refrigerants to that of R-410A and R-404A for heat pump and medium temperature applications, respectively. The alternatives reported in this paper are: R-32, DR-5, and L-41a for R-410A and ARM-31a, D2Y-65, L-40, and a mixture of R-32 and R-134a for R-404A. All performance comparison tests were conducted using scroll compressors of ~1.85 tons (6.5 kW) cooling capacity. Tests were conducted over a range of combinations of saturation suction and saturation discharge temperatures for both compressors. The tests showed that, in general, energy efficiency ratio (EER) and cooling capacity of R-410A alternative refrigerants were slightly lower than that of the baseline refrigerant with a moderate increases in discharge temperature. On the other hand, R-404A alternative refrigerants showed relative performance dependence on saturation suction and saturation discharge temperatures and larger increases in discharge temperature than for the R-410A alternatives. This paper summarizes the relative performance of all alternative refrigerants compared to their respective baseline.

  13. IEMDC IN-LINE ELECTRIC MOTOR DRIVEN COMPRESSOR

    SciTech Connect (OSTI)

    Michael J. Crowley; Prem N. Bansal

    2004-10-01

    This report contains the final project summary and deliverables required by the award for the development of an In-line Electric Motor Driven Compressor (IEMDC). Extensive work was undertaken during the course of the project to develop the motor and the compressor section of the IEMDC unit. Multiple design iterations were performed to design an electric motor for operation in a natural gas environment and to successfully integrate the motor with a compressor. During the project execution, many challenges were successfully overcome in order to achieve the project goals and to maintain the system design integrity. Some of the challenges included limiting the magnitude of the compressor aerodynamic loading for appropriate sizing of the magnetic bearings, achieving a compact motor rotor size to meet the rotor dynamic requirements of API standards, devising a motor cooling scheme using high pressure natural gas, minimizing the impact of cooling on system efficiency, and balancing the system thrust loads for the magnetic thrust bearing. Design methods that were used on the project included validated state-of-the-art techniques such as finite element analysis and computational fluid dynamics along with the combined expertise of both Curtiss-Wright Electro-Mechanical Corporation and Dresser-Rand Company. One of the most significant areas of work undertaken on the project was the development of the unit configuration for the system. Determining the configuration of the unit was a significant step in achieving integration of the electric motor into a totally enclosed compression system. Product review of the IEMDC unit configuration was performed during the course of the development process; this led to an alternate design configuration. The alternate configuration is a modular design with the electric motor and compressor section each being primarily contained in its own pressure containing case. This new concept resolved the previous conflict between the aerodynamic flow passage requirements and electric motor requirements for support and utilities by bounding the flowpath within the compressor section. However most importantly, the benefits delivered by the new design remained the same as those proposed by the goals of the project. In addition, this alternate configuration resulted in the achievement of a few additional advantages over the original concept such as easier maintenance, operation, and installation. Interaction and feedback solicited from target clients regarding the unit configuration supports the fact that the design addresses industry issues regarding accessibility, maintainability, preferred operating practice, and increased reliability.

  14. High Technology Centrifugal Compressor for Commercial Air Conditioning Systems

    SciTech Connect (OSTI)

    Ruckes, John

    2006-04-15

    R&D Dynamics, Bloomfield, CT in partnership with the State of Connecticut has been developing a high technology, oil-free, energy-efficient centrifugal compressor called CENVA for commercial air conditioning systems under a program funded by the US Department of Energy. The CENVA compressor applies the foil bearing technology used in all modern aircraft, civil and military, air conditioning systems. The CENVA compressor will enhance the efficiency of water and air cooled chillers, packaged roof top units, and other air conditioning systems by providing an 18% reduction in energy consumption in the unit capacity range of 25 to 350 tons of refrigeration The technical approach for CENVA involved the design and development of a high-speed, oil-free foil gas bearing-supported two-stage centrifugal compressor, CENVA encompassed the following high technologies, which are not currently utilized in commercial air conditioning systems: Foil gas bearings operating in HFC-134a; Efficient centrifugal impellers and diffusers; High speed motors and drives; and System integration of above technologies. Extensive design, development and testing efforts were carried out. Significant accomplishments achieved under this program are: (1) A total of 26 builds and over 200 tests were successfully completed with successively improved designs; (2) Use of foil gas bearings in refrigerant R134a was successfully proven; (3) A high speed, high power permanent magnet motor was developed; (4) An encoder was used for signal feedback between motor and controller. Due to temperature limitations of the encoder, the compressor could not operate at higher speed and in turn at higher pressure. In order to alleviate this problem a unique sensorless controller was developed; (5) This controller has successfully been tested as stand alone; however, it has not yet been integrated and tested as a system; (6) The compressor successfully operated at water cooled condensing temperatures Due to temperature limitations of the encoder, it could not be operated at air cooled condensing temperatures. (7) The two-stage impellers/diffusers worked well separately but combined did not match well.

  15. Linear Gain for the Microbunching Instability in an RF Compressor

    SciTech Connect (OSTI)

    Venturini, M.; Migliorati, M.; Ronsivalle, C.; Vaccarezza, C.

    2009-05-01

    Velocity (or rf) compression has been suggested as a technique for bunch compression complementary to the more established technique involving magnetic chicanes and represents an important research item being investigated at the SPARC test facility. One of the aspects of this technique still not sufficiently understood is its possible impact on the microbunching instability. The purpose of this report is to present the analytical framework for investigating this instability in rf compressors. We use methods similar to those successfully applied to magnetic compressors and derive some integral equations yielding the gain for the instability in linear approximation. The focus here is on the derivation of the relevant equations. Although examples of solutions to these equations are provided we defer a more comprehensive discussion of their implication to a future report. The present study is part of a larger effort for a more comprehensive investigation that eventually will include macroparticle simulations and experiments.

  16. IEMDC-IN-LINE ELECTRIC MOTOR DRIVEN COMPRESSOR

    SciTech Connect (OSTI)

    Michael J. Crowley; Prem N. Bansal; John E. Tessaro

    2003-06-01

    During this reporting period, significant progress has been made towards the development of the IEMDC System design. Considerable effort was put forth by Curtiss-Wright EMD in the resolution of the technical issue of aerodynamically induced radial forces. This has provided a design basis with which to establish the radial magnetic bearing load capacity and the rotordynamic design. Dresser-Rand has made considerable progress on the flowpath design for the compressor section particularly on the volute and inlet aerodynamic design. All efforts show progression towards the successful integration of a centrifugal compressor and variable speed electric motor ventilated by the process gas. These efforts continue to confirm the feasibility of the IEMDC system design.

  17. Quasi-Optical 34-GHz Rf Pulse Compressor

    SciTech Connect (OSTI)

    Hirshfield, Jay L

    2007-06-19

    Designs have been carried out on non-high-vacuum, low-power versions of three- and four-mirror quasi-optical passive and active Ka-band pulse compressors, and prototypes built and tested based on these designs. The active element is a quasi-optical grating employing gas discharge tubes in the gratings. Power gains of about 3:1 were observed experimentally for the passive designs, and about 7:1 with the active designs. High-power, high-vacuum versions of the three-and four-mirror quasi-optical pulse compressors were built and tested at low power. These now await installation and testing using multi-MW power from the 34-GHz magnicon.

  18. RF modulation studies on the S band pulse compressor

    E-Print Network [OSTI]

    Shu, G; Pei, S; Xiao, O

    2015-01-01

    An S band SLED-type pulse compressor has been manufactured by IHEP to challenge the 100 MW maximum input power, which means the output peak power is about 500 MW at the phase reversal time. In order to deal with the RF breakdown problem, the dual side-wall coupling irises model was used. To further improve the reliability at very high power, amplitude modulation and phase modulation with flat-top output were taken into account. The RF modulation studies on an S-band SLED are presented in this paper. Furthermore, a method is developed by using the CST Microwave Studio transient solver to simulate the time response of the pulse compressor, which can be a verification of the modulate theory. In addition, the experimental setup was constructed and the flat-top output is obtained in the low power tests.

  19. RF modulation studies on the S band pulse compressor

    E-Print Network [OSTI]

    G. Shu; F. Zhao; S. Pei; O. Xiao

    2015-05-28

    An S band SLED-type pulse compressor has been manufactured by IHEP to challenge the 100 MW maximum input power, which means the output peak power is about 500 MW at the phase reversal time. In order to deal with the RF breakdown problem, the dual side-wall coupling irises model was used. To further improve the reliability at very high power, amplitude modulation and phase modulation with flat-top output were taken into account. The RF modulation studies on an S-band SLED are presented in this paper. Furthermore, a method is developed by using the CST Microwave Studio transient solver to simulate the time response of the pulse compressor, which can be a verification of the modulate theory. In addition, the experimental setup was constructed and the flat-top output is obtained in the low power tests.

  20. Plasma Switch for High-Power Active Pulse Compressor

    SciTech Connect (OSTI)

    Hirshfield, Jay L. [Omega-P, Inc.] [Omega-P, Inc.

    2013-11-04

    Results are presented from experiments carried out at the Naval Research Laboratory X-band magnicon facility on a two-channel X-band active RF pulse compressor that employed plasma switches. Experimental evidence is shown to validate the basic goals of the project, which include: simultaneous firing of plasma switches in both channels of the RF circuit, operation of quasi-optical 3-dB hybrid directional coupler coherent superposition of RF compressed pulses from both channels, and operation of the X-band magnicon directly in the RF pulse compressor. For incident 1.2 ?s pulses in the range 0.63 ? 1.35 MW, compressed pulses of peak powers 5.7 ? 11.3 MW were obtained, corresponding to peak power gain ratios of 8.3 ? 9.3. Insufficient bakeout and conditioning of the high-power RF circuit prevented experiments from being conducted at higher RF input power levels.

  1. Heat powered refrigeration compressor. Semi-annual technical report

    SciTech Connect (OSTI)

    Goad, R.R.

    1981-01-01

    The objective of this program is to develop and improve the design of previously started prototypes of the Heat Powered Refrigeration Compressor. To build this prototype and ready it for testing by the University of Evansville is another goal. This prototype will be of similar capacity as the compressor that will eventually be commercially produced. This unit can operate on almost any moderate temperature water heat source. This heat source could include such applications as industrial waste heat, solar, wood burning stove, resistance electrical heat produced by a windmill, or even perhaps heat put out by the condenser of another refrigeration system. Work performed in the past four months has consisted of: engineering of HX-1; comparisons of specifications from different companies to ensure state of the art applications of parts for project; coordinating project requirements with machine shop; designing condenser; and partial assembly of HX-1.

  2. Turbine inter-disk cavity cooling air compressor

    DOE Patents [OSTI]

    Little, David Allen (Oviedo, FL)

    2001-01-01

    A combustion turbine may have a cooling circuit for directing a cooling medium through the combustion turbine to cool various components of the combustion turbine. This cooling circuit may include a compressor, a combustor shell and a component of the combustion turbine to be cooled. This component may be a rotating blade of the combustion turbine. A pressure changing mechanism is disposed in the combustion turbine between the component to be cooled and the combustor shell. The cooling medium preferably flows from the compressor to the combustor shell, through a cooler, the component to the cooled and the pressure changing mechanism. After flowing through the pressure changing mechanism, the cooling medium is returned to the combustor shell. The pressure changing mechanism preferably changes the pressure of the cooling medium from a pressure at which it is exhausted from the component to be cooled to approximately that of the combustor shell.

  3. Downhole steam generator having a downhole oxidant compressor

    DOE Patents [OSTI]

    Fox, R.L.

    1981-01-07

    Am improved apparatus is described for the downhole injection of steam into boreholes, for tertiary oil recovery. It includes an oxidant supply, a fuel supply, an igniter, a water supply, an oxidant compressor, and a combustor assembly. The apparatus is designed for efficiency, preheating of the water, and cooling of the combustion chamber walls. The steam outlet to the borehole is provided with pressure-responsive doors for closing the outlet in response to flameout. (DLC)

  4. Screw Type Steam Compressors for Mechanical Vapor Recompression (MVR) Systems 

    E-Print Network [OSTI]

    Kawamura, K.; Apaloo, Thomas-L.

    1986-01-01

    hand, is not affected by such problem. No special mist separator is required and, at the same time, the wet or saturated vapor compression is possible, and does not affect the efficiency of the SSHP. (3) Stability of performance for a wide... COMPRESSORS FOR MECHANICAL VAPOR RECOMPRESSION (MVR) SYSTEMS K. KAWAMURA AND THOMAS-L. APALOO MYCOM CORPORATION, LOS ANGELES, CALIFORNIA MATSUDA, MAYEKAWA MFG. CO., TOKYO, JAPAN ABSTRACT In processes of evaporation, distillation or drying, steam...

  5. OAK RIDGE NATIONAL LABORATORY U.S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    1 OAK RIDGE NATIONAL LABORATORY U.S. DEPARTMENT OF ENERGY OAK RIDGE NATIONAL LABORATORY U.S. DEPARTMENT OF ENERGY OAK RIDGE NATIONAL LABORATORY U.S. DEPARTMENT OF ENERGY BPWorkshop-2005 - LRB OAK RIDGE NATIONAL LABORATORY U.S. DEPARTMENT OF ENERGY presented by L.R. Baylor in collaboration with P.B. Parks*, S

  6. Inconsistent Application of Environmental Laws and Policies to California's Oak

    E-Print Network [OSTI]

    Inconsistent Application of Environmental Laws and Policies to California's Oak Woodlands1 Gregory of environmental laws and policies to California's oak woodlands and associated resources. Specifically, large of Environmental Laws and Policies to California's Oak Woodlands-- Giusti and Merenlender Oaks continue

  7. Modeling shrouded stator cavity flows in axial-flow compressors

    SciTech Connect (OSTI)

    Wellborn, S.R.; Tolchinsky, I.; Okiishi, T.H.

    2000-01-01

    Experiments and computational analyses were completed to understand the nature of shrouded stator cavity flows. From this understanding, a one-dimensional model of the flow through shrouded stator cavities was developed. This model estimates the leakage mass flow, temperature rise, and angular momentum increase through the cavity, given geometry parameters and the flow conditions at the interface between the cavity and primary flow path. This cavity model consists of two components, one that estimates the flow characteristics through the labyrinth seals and the other that predicts the transfer of momentum due to windage. A description of the one-dimensional model is given. The incorporation and use of the one-dimensional model in a multistage compressor primary flow analysis tool is described. The combination of this model and the primary flow solver was used to reliably simulate the significant impact on performance of the increase of hub seal leakage in a twelve-stage axial-flow compressor. Observed higher temperatures of the hub region fluid, different stage matching, and lower overall efficiencies and core flow than expected could be correctly linked to increased hub seal clearance with this new technique. The importance of including these leakage flows in compressor simulations is shown.

  8. A new endwall model for axial compressor throughflow calculations

    SciTech Connect (OSTI)

    Dunham, J.

    1995-10-01

    It is well recognized that the endwall regions of a compressor--in which the annulus wall flow interacts with the mainstream flow--have a major influence on its efficiency and surge margin. Despite many attempts over the years to predict the very complex flow patterns in the endwall regions, current compressor design methods still rely largely on empirical estimates of the aerodynamic losses and flow angle deviations in these regions. This paper describes a new phenomenological model of the key endwall flow phenomena treated in a circumferentially averaged way. It starts from Hirsch and de Ruyck`s annulus wall boundary layer approach, but makes some important changes. The secondary vorticities arising from passage secondary flows and from tip clearance flows are calculated. Then the radial interchanges of momentum, energy, and entropy arising from both diffusion and convection are estimated. The model is incorporated into a streamline curvature program. The empirical blade force defect terms in the boundary layers are selected from cascade data. The effectiveness of the method is illustrated by comparing the predictions with experimental results on both low-speed and high-speed multistage compressors. It is found that the radial variation of flow parameters is quite well predicted, and so is the overall performance, except when significant endwall stall occurs.

  9. An analysis of axial compressor fouling and a blade cleaning method

    SciTech Connect (OSTI)

    Tarabrin, A.P.; Schurovsky, V.A.; Bodrov, A.I.; Stalder, J.P.

    1998-04-01

    The paper describes the phenomenon of axial compressor fouling due to aerosols contained in the air. Key parameters having effect on the level of fouling are determined. A mathematical model of a progressive compressor fouling using the stage-by-stage calculation method is developed. Calculation results on the influence of fouling on the compressor performance are presented. A new index of sensitivity of axial compressors to fouling is suggested. The paper gives information about Turbotect`s deposit cleaning method of compressor blading and the results of its application on an operating industrial gas turbine. Regular on-line and off-line washings of the compressor flow path made it possible to maintain a high level of engine efficiency and output.

  10. Simulating Energy Efficient Control of Multiple-Compressor Compressed Air Systems 

    E-Print Network [OSTI]

    Murphy, S.

    2015-01-01

    with multiple compressors contain greater opportunity for controls optimization. The three main types of multiple- compressor control strategies which will be discussed in this paper are: pressure band control, network sequencer control, and automatic..., the basic principles and control algorithms are detailed for pressure band control, network sequencer control, and automatic sequencer control strategies for multiple-compressor compressed air systems. Finally, a case study is presented demonstrating...

  11. Oak Ridge Office of Environmental Management

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak of EnvironmentalY-12Oak I1Oak

  12. Dual capacity compressor with reversible motor and controls arrangement therefor

    DOE Patents [OSTI]

    Sisk, Francis J. (Washington Township, Fayette County, PA)

    1980-12-02

    A hermetic reciprocating compressor such as may be used in heat pump applications is provided for dual capacity operation by providing the crankpin of the crankshaft with an eccentric ring rotatably mounted thereon, and with the end of the connecting rod opposite the piston encompassing the outer circumference of the eccentric ring, with means limiting the rotation of the eccentric ring upon the crankpin between one end point and an opposite angularly displaced end point to provide different values of eccentricity depending upon which end point the eccentric ring is rotated to upon the crankpin, and a reversible motor in the hermetic shell of the compressor for rotating the crankshaft, the motor operating in one direction effecting the angular displacement of the eccentric ring relative to the crankpin to the one end point, and in the opposite direction effecting the angular displacement of the eccentric ring relative to the crankpin to the opposite end point, this arrangement automatically giving different stroke lengths depending upon the direction of motor rotation. The mechanical structure of the arrangement may take various forms including at least one in which any impact of reversal is reduced by utilizing lubricant passages and chambers at the interface area of the crankpin and eccentric ring to provide a dashpot effect. In the main intended application of the arrangement according to the invention, that is, in a refrigerating or air conditioning system, it is desirable to insure a delay during reversal of the direction of compressor operation. A control arrangement is provided in which the control system controls the direction of motor operation in accordance with temperature conditions, the system including control means for effecting operation in a low capacity direction or alternatively in a high capacity direction in response to one set, and another set, respectively, of temperature conditions and with timer means delaying a restart of the compressor motor for at least a predetermined time in response to a condition of the control means operative to initiate a change in the operating direction of the compressor when it restarts.

  13. Rotor dynamic analysis of GCEP (Gas Centrifuge Enrichment Plant) Tails Withdrawal Test Facility AC-12 compressor

    SciTech Connect (OSTI)

    Spencer, J.W.

    1982-01-22

    The reliable operation of the centrifugal compressors utilized in the gaseous diffusion process is of great importance due to the critical function of these machines in product and tails withdrawal, cascade purge and evacuation processes, the purge cascade and product booster applications. The same compressors will be used in equally important applications within the Gas Centrifuge Enrichment Plant (GCEP). In response to concern over the excessive vibration exhibited by the AC-12 compressor in the No. 3 position of the GCEP Tails Withdrawal Test Facility, a rotor-bearing dynamic analysis was performed on the compressor. This analysis included the acquisition and reduction of compressor vibration data, characterization and modeling of the rotorbearing system, a computer dynamic study, and recommendations for machine modification. The compressor dynamic analysis was performed for rotor speeds of 9000 rpm and 7200 to 7800 rpm, which includes all possible opreating speeds of the compressor in the GCEP Test Facility. While the analysis was performed on this particular AC-12 compressor, the results should be pertinent to other AC-12 applications as well. Similar diagnostic and analytical techniques can be used to evaluate operation of other types of centrifugal compressors.

  14. The potential use of thiabendazole and propiconazole for oak wilt control in live oak 

    E-Print Network [OSTI]

    Roberts, Paul Edwin

    1988-01-01

    analysis with a variable acceptance level of 0. 15. 28 Models tested for xylem pressure potential, using stepwise regression analysis with a variable acceptance level of 0. 15. . . . . . . . . . . . 29 Phytotoxicity rating of live oaks injected...THE POTENTIAL USE OF THIABENDAZOLE AND PROPICONAZOLE FOR OAK WILT CONTROL IN LIVE OAK A Thesis by PAUL EDWIN ROBERTS Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER...

  15. Introduction to the Oak Ridge Reservation 1-1 1. Introduction to the Oak Ridge Reservation

    E-Print Network [OSTI]

    Pennycook, Steve

    purposes, such as environmental restoration/remedial investigation reports, waste management sector business/industrial park; the Oak Ridge Institute for Science and Education (ORISE) South Campus

  16. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    Bruce Hicks, Vice Chair Howard Holmes Jennifer Kasten Belinda Price Mary Smalling Wanda Smith Corkie Staley Others present Dave Adler, DOE-Oak Ridge Office (DOE-ORO), Alternate...

  17. Major Oak Diseases and Their Control. 

    E-Print Network [OSTI]

    Johnson, Jerral D.; Appel, David N.

    1984-01-01

    in many areas where oaks are the predominant native tree species. Research shows that much of this mortality is due to disease-causing organisms or disease complexes 10- volving environmental stress and pathogens. FOLIAR DISEASES Anthracnose (Fungus... tor nado, hurricane, severe hail or following a period of mechanical activity around oak trees. Heavy equip- ment working around trees can create large wounds. When this occurs, insects are attracted to the site and may be carrying the wilt...

  18. Oak Ridge Reservation environmental report for 1989

    SciTech Connect (OSTI)

    Jacobs, V.A.; Wilson, A.R.

    1990-10-01

    This two-volume report, the Oak Ridge Reservation Environmental Report for 1989, is the nineteenth in an annual series that began in 1971. It reports the results of a comprehensive, year-round program to monitor the impact of operations at the three major US Department of Energy (DOE) production and research installations in Oak Ridge on the immediate areas' and surrounding region's groundwater and surface waters, soil, air quality, vegetation and wildlife, and through these multiple and varied pathways, the resident human population. Information is presented for the environmental monitoring Quality Assurance (QA) Program, audits and reviews, waste management activities, land special environmental studies. Data are included for the Oak Ridge Y-12 Plant, Oak Ridge National Laboratory (ORNL), and Oak Ridge Gaseous Diffusion Plant (ORGDP). Volume 1 presents narratives, summaries, and conclusions based on environmental monitoring at the three DOE installations and in the surrounding environs during calendar year (CY) 1989. Volume 1 is intended to be a stand-alone'' report about the Oak Ridge Reservation (ORR) for the reader who does not want an in-depth review of 1989 data. Volume 2 presents the detailed data from which these conclusions have been drawn and should be used in conjunction with Volume 1.

  19. Dynamic Optimization in Gas Pipeline Networks EWO MEETING, Spring 2012

    E-Print Network [OSTI]

    Grossmann, Ignacio E.

    , consumers and compressor stations Compressor Stations Processing Plants Customers 3 Suppliers: Continuous flow of gas into network. Customers: Chemical industries, Power plants, Residential/commercial heating: Flow demands must be satisfied at a contract pressure. Compressor Stations: Compression of gas

  20. Oak Ridge Associated Universities II

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield Municipal Gas &SCE-SessionsSouthReport for the Weldon Spring,7=cr5rnP 7694 i+lJNewS e TAugust

  1. Background review on compressors for gas engine-driven heat pumps. Technical report, September 1985-March 1986

    SciTech Connect (OSTI)

    Hall, R.L.; Swain, J.C.

    1986-04-01

    The investigation focused on the efficiency and durability of various types of open-shaft compressors for potential application to residential and light commercial gas-engine-driven heat-pump applications. Variable speed efficiency data for hermetic, semihermetic, and open shaft compressors were obtained from the public literature and from compressor manufacturers in the US, Japan, and in Europe. Efficiency comparisons based upon refrigerants R12 and R22 at a fixed compressor pressure ratio indicate that reciprocating compressors have the highest coefficients of performance (COP's) for compressor speeds ranging from 1000 to 2500 rpm. Scroll and Wankel compressors appear to offer the highest COP's above 2500 rpm. An important finding of the work is that open shaft compressors with proven life and reliability for residential gas engine heat-pump applications do not appear to be available as production units.

  2. Oak Ridge National Laboratory 5-1 5. Oak Ridge National Laboratory

    E-Print Network [OSTI]

    Pennycook, Steve

    science, energy, high-performance computing, systems biology, and national security. ORNL partnersOak Ridge National Laboratory 5-1 5. Oak Ridge National Laboratory ORNL is the largest science and energy national laboratory in the DOE system. ORNL's scientific programs focus on materials, neutron

  3. Oak Ridge National Laboratory 5-1 5. Oak Ridge National Laboratory

    E-Print Network [OSTI]

    Pennycook, Steve

    science, energy, high-performance computing, systems biology, and national security. ORNL partners1 Oak Ridge National Laboratory 5-1 5. Oak Ridge National Laboratory ORNL is the largest science and energy national laboratory in the DOE system. ORNL's scientific programs focus on materials, neutron

  4. Three-dimensional flow visualization in a centrifugal compressor 

    E-Print Network [OSTI]

    Trevillion, William Lee

    1976-01-01

    of this boundary layer problem should enable designers to design compressors with higher efficiencies and larger surge-to-stall margins. Wiesner Stodola Busemann Eck 0. 9 B 0 m 0. 8 pfleiderer Senoo a Nakase ~ ~ 0. 7 ~ Experimental results 0. 6 0... increase during its flow through the impeller. The outer diameter of the rotor, D , was designed to be 7. 00 inches with an exit blade height, b2, of 0. 50 inches. The hub and blades were machined from aluminum and polished to aid observation...

  5. Passivity based compressor surge control using a close-coupled valve

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    Passivity based compressor surge control using a close-coupled valve Jan Tommy Gravdahl and Olav-coupled valve. The analysis shows that the system has certain passivity properties which leads to a simple controller for the close- coupled valve. 1 Introduction If the ow through a compressor is throttled

  6. Design of a Free Piston Pneumatic Compressor as a Mobile Robot Power Supply

    E-Print Network [OSTI]

    Barth, Eric J.

    technology is intended to provide a compact pneumatic power supply source appropriate for human-scale robotsDesign of a Free Piston Pneumatic Compressor as a Mobile Robot Power Supply Jose A. Riofrio.j.barth@vanderbilt.edu Abstract ­ The design of a free piston compressor (FPC) intended as a pneumatic power supply

  7. 1275, Page 1 ANALYSIS AND DEVELOPMENT OF A TURBIVO COMPRESSOR FOR MVR

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    dryers is the use of a compressor with high efficiency in an open cycle and at high evaporating development issue. Typical clothe dryers consume 750 Wh/kg of dry clothes. Dryers with thermodynamic cycle can-stage configuration for high flow rate and high compression power (> 100 kW) [2]. Volumetric compressors are divided

  8. High Fidelity Modeling of Blade Row Interaction in a Transonic Compressor

    E-Print Network [OSTI]

    Cincinnati, University of

    High Fidelity Modeling of Blade Row Interaction in a Transonic Compressor Michael G. List on the compressor. Three dierent axial spacings between the rotor and the upstream blade row have been simulated of Cincinnati, Cincinnati, OH, 45221 In order to accurately model the physics associated with losses

  9. A Model of Compressor Blade Row Interaction with Shock Induced Vortex Shedding

    E-Print Network [OSTI]

    Cincinnati, University of

    A Model of Compressor Blade Row Interaction with Shock Induced Vortex Shedding Mark G. Turner". The mid and far spacings represent typical axial gaps found in operational fans and compressors. However behind a stator are modeled. The model is based on a Burger vortex core model for shed vortices

  10. Performance Testing of Jefferson Lab 12 GeV Helium Screw Compressors

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Knudsen, P.; Ganni, V.; Dixon, K.; Norton, R.; Creel, J.

    2015-08-10

    Oil injected screw compressors have essentially superseded all other types of compressors in modern helium refrigeration systems due to their large displacement capacity, reliability, minimal vibration, and capability of handling helium's high heat of compression. At the present state of compressor system designs for helium refrigeration systems, typically two-thirds of the lost input power is due to the compression system. It is important to understand the isothermal and volumetric efficiencies of these machines to help properly design the compression system to match the refrigeration process. It is also important to identify those primary compressor skid exergetic loss mechanisms which maymore »be reduced, thereby offering the possibility of significantly reducing the input power to helium refrigeration processes which are extremely energy intensive. This paper summarizes the results collected during the commissioning of the new compressor system for Jefferson Lab's (JLab's) 12 GeV upgrade. The compressor skid packages were designed by JLab and built to print by industry. They incorporate a number of modifications not typical of helium screw compressor packages and most importantly allow a very wide range of operation so that JLab's patented Floating Pressure Process can be fully utilized. This paper also summarizes key features of the skid design that allow this process and facilitate the maintenance and reliability of these helium compressor systems.« less

  11. Testing and modeling of compressors for low-lift cooling applications

    E-Print Network [OSTI]

    Willingham, Ryan Alexander

    2009-01-01

    In this thesis, an inverter-driven variable speed scroll compressor is tested on a de-superheater test stand to determine its performance in areas of low-lift and low compressor speed. The goal is to adapt this test stand ...

  12. Bunch Compressor for the TESLA Linear Collider W. Decking, G. Hoffstaetter, T. Limberg

    E-Print Network [OSTI]

    Hoffstaetter, Georg

    Bunch Compressor for the TESLA Linear Collider W. Decking, G. Hoffstaetter, T. Limberg DESY, Notkestraße 85, 22603 Hamburg, Germany September 2000 Abstract TESLA-2000-40 (2000) We discuss different bunch compression systems for the TESLA collider. The best alternative is a wiggler type compressor, where we list

  13. 2009-32-0176/20097176 Miniature HCCI Free-Piston Engine Compressor

    E-Print Network [OSTI]

    Durfee, William K.

    -cycle combustion is used. Free-piston engine compressor Accumulator Rotary actuator #12;SETC2009 ComparedSETC2009 2009-32-0176/20097176 Miniature HCCI Free-Piston Engine Compressor For Orthosis Application Lei Tian, David B. Kittelson, William K. Durfee Mechanical Engineering, University of Minnesota

  14. The development of an aquatic spill model for the White Oak Creek watershed, Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Johnson, R.O.

    1996-05-01

    This study develops an aquatic spill model applicable to the White Oak Creek watershed draining the Oak Ridge National Laboratory. Hazardous, toxic, and radioactive chemicals are handled and stored on the laboratory reservation. An accidental spill into the White Oak Creek watershed could contaminate downstream water supplies if insufficient dilution did not occur. White Oak Creek empties into the Clinch River, which flows into the Tennessee River. Both rivers serve as municipal water supplies. The aquatic spill model provides estimates of the dilution at sequential downstream locations along White Oak creek and the Clinch River after an accidental spill of a liquid containing a radioactively decaying constituent. The location of the spill on the laboratory is arbitrary, while hydrologic conditions range from drought to extreme flood are simulated. The aquatic spill model provides quantitative estimates with which to assess water quality downstream from the site of the accidental spill, allowing an informed decision to be made whether to perform mitigating measures so that the integrity of affected water supplies is not jeopardized.

  15. IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY, VOL. 7, NO. 5, SEPTEMBER 1999 567 Centrifugal Compressor Surge and Speed Control

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY, VOL. 7, NO. 5, SEPTEMBER 1999 567 Centrifugal of the compressor. First a low-order centrifugal compressor model is presented where the states are mass flow] showed that it is also applicable to centrifugal compressors. The model has two states, normalized mass

  16. Performance analysis of a series of hermetic reciprocating compressors working with R290 (propane) and R407C

    E-Print Network [OSTI]

    Fernández de Córdoba, Pedro

    Performance analysis of a series of hermetic reciprocating compressors working with R290 (propane with propane as refrigerant are analyzed in terms of the compressor model developed by [E. Navarro, E. Granryd. In addition, a comparison study between propane and R407C was carried out for one compressor and the observed

  17. Compressor discharge bleed air circuit in gas turbine plants and related method

    DOE Patents [OSTI]

    Anand, Ashok Kumar (Niskayuna, NY); Berrahou, Philip Fadhel (Latham, NY); Jandrisevits, Michael (Clifton Park, NY)

    2002-01-01

    A gas turbine system that includes a compressor, a turbine component and a load, wherein fuel and compressor discharge bleed air are supplied to a combustor and gaseous products of combustion are introduced into the turbine component and subsequently exhausted to atmosphere. A compressor discharge bleed air circuit removes bleed air from the compressor and supplies one portion of the bleed air to the combustor and another portion of the compressor discharge bleed air to an exhaust stack of the turbine component in a single cycle system, or to a heat recovery steam generator in a combined cycle system. In both systems, the bleed air diverted from the combustor may be expanded in an air expander to reduce pressure upstream of the exhaust stack or heat recovery steam generator.

  18. Compressor discharge bleed air circuit in gas turbine plants and related method

    DOE Patents [OSTI]

    Anand, Ashok Kumar (Niskayuna, NY); Berrahou, Philip Fadhel (Latham, NY); Jandrisevits, Michael (Clifton Park, NY)

    2003-04-08

    A gas turbine system that includes a compressor, a turbine component and a load, wherein fuel and compressor discharge bleed air are supplied to a combustor and gaseous products of combustion are introduced into the turbine component and subsequently exhausted to atmosphere. A compressor discharge bleed air circuit removes bleed air from the compressor and supplies one portion of the bleed air to the combustor and another portion of the compressor discharge bleed air to an exhaust stack of the turbine component in a single cycle system, or to a heat recovery steam generator in a combined cycle system. In both systems, the bleed air diverted from the combustor may be expanded in an air expander to reduce pressure upstream of the exhaust stack or heat recovery steam generator.

  19. The use of neural nets for matching compressors with diesel engines

    SciTech Connect (OSTI)

    Nelson, S.A. II; Filipi, Z.S.; Assanis, D.N.

    1996-12-31

    A technique which uses trained neural nets to model the compressor in the context of a turbocharged diesel engine simulation is introduced. This technique replaces the usual interpolation of compressor maps with the evaluation of a smooth mathematical function, thus providing engine simulations with greater robustness and flexibility. Following presentation of the methodology, the proposed neural net technique is validated against data from a truck type, 6-cylinder, 14 liter diesel engine. Furthermore, with the introduction of an additional parameter, the proposed neural net can be trained to simulate an entire family of compressors. As a demonstration, five compressors of different sizes are represented with the neural net model, and used for matching calculations with intercooled and non-intercooled engine configurations at different speeds. This novel approach readily allows for evaluation of various options prior to prototype production, and is thus a powerful design tool for selection of the best compressor for a given diesel engine system.

  20. Detector for flow abnormalities in gaseous diffusion plant compressors

    DOE Patents [OSTI]

    Smith, Stephen F. (Loudon, TN); Castleberry, Kim N. (Harriman, TN)

    1998-01-01

    A detector detects a flow abnormality in a plant compressor which outputs a motor current signal. The detector includes a demodulator/lowpass filter demodulating and filtering the motor current signal producing a demodulated signal, and first, second, third and fourth bandpass filters connected to the demodulator/lowpass filter, and filtering the demodulated signal in accordance with first, second, third and fourth bandpass frequencies generating first, second, third and fourth filtered signals having first, second, third and fourth amplitudes. The detector also includes first, second, third and fourth amplitude detectors connected to the first, second, third and fourth bandpass filters respectively, and detecting the first, second, third and fourth amplitudes, and first and second adders connected to the first and fourth amplitude detectors and the second and third amplitude detectors respectively, and adding the first and fourth amplitudes and the second and third amplitudes respectively generating first and second added signals. Finally, the detector includes a comparator, connected to the first and second adders, and comparing the first and second added signals and detecting the abnormal condition in the plant compressor when the second added signal exceeds the first added signal by a predetermined value.

  1. Detector for flow abnormalities in gaseous diffusion plant compressors

    DOE Patents [OSTI]

    Smith, S.F.; Castleberry, K.N.

    1998-06-16

    A detector detects a flow abnormality in a plant compressor which outputs a motor current signal. The detector includes a demodulator/lowpass filter demodulating and filtering the motor current signal producing a demodulated signal, and first, second, third and fourth bandpass filters connected to the demodulator/lowpass filter, and filtering the demodulated signal in accordance with first, second, third and fourth bandpass frequencies generating first, second, third and fourth filtered signals having first, second, third and fourth amplitudes. The detector also includes first, second, third and fourth amplitude detectors connected to the first, second, third and fourth bandpass filters respectively, and detecting the first, second, third and fourth amplitudes, and first and second adders connected to the first and fourth amplitude detectors and the second and third amplitude detectors respectively, and adding the first and fourth amplitudes and the second and third amplitudes respectively generating first and second added signals. Finally, the detector includes a comparator, connected to the first and second adders, and comparing the first and second added signals and detecting the abnormal condition in the plant compressor when the second added signal exceeds the first added signal by a predetermined value. 6 figs.

  2. English Country Dance 2015 Parking in Oak Park

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Parking in Oak Park Due to major construction, parking for the Oak Park dances is a bit challenging, so please allow yourself a little more time and patience. Below are parking...

  3. Oak Ridge Site Specific Advisory Board Contacts | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Mailing Address Oak Ridge Site Specific Advisory Board P.O. Box 2001, EM-91 Oak Ridge, TN 37831 Phone Numbers (865) 241-4583, (865) 241-4584 (800) 382-6938, option 4 Melyssa Noe,...

  4. UT OAK RIDGE FACILITY To Y-12 National

    E-Print Network [OSTI]

    5 UT ­ OAK RIDGE FACILITY To Y-12 National Security Complex To East Tennessee Technology Park (ETTP To Oak Ridge National Laboratory 9 3 2 4 1 9 7 6 8 TU LANE TU LANE NEWYORK UT OUTREACH CENTER UT

  5. Blue oak seedlings may be older than they look

    E-Print Network [OSTI]

    Blue oak seedlings may be older than they look Ralph L. Phillips u Neil K. McDougald o Richard B. Standiford William E.Frost A 4-year study indicates that na- tive blue oak seedlings are prob- ably much the year of above- average rainfall. Blue oak (Quercusdouglasii)trees are a valuable economic and aesthetic

  6. DOE/ORO/2296 Oak Ridge Reservation Annual Site

    E-Print Network [OSTI]

    Pennycook, Steve

    #12;#12;DOE/ORO/2296 Oak Ridge Reservation Annual Site Environmental Report for 2008 on the World Project manager, DOE-ORO David Page September 2009 Prepared by Oak Ridge National Laboratory P.O. Box 2008 ........................................................................................................................ 1-1 1.2 History of the Oak Ridge Reservation

  7. Oak Ridge ReseRvatiOn DOE/ORO/2379

    E-Print Network [OSTI]

    Pennycook, Steve

    Oak Ridge ReseRvatiOn DOE/ORO/2379 Annual Site Environmental Report 2010 #12;Cover Image and Design Annual Site Environmental Report 2010 #12;DOE/ORO/2379 Oak Ridge Reservation Annual Site Environmental ................................................................................................................................1-1 1.2 History of the Oak Ridge Reservation

  8. DOE/ORO/2261 Oak Ridge Reservation Annual Site

    E-Print Network [OSTI]

    Pennycook, Steve

    #12;#12;DOE/ORO/2261 Oak Ridge Reservation Annual Site Environmental Report for 2007 on the World, Jane Parrott Project manager, DOE-ORO David Page September 2008 Prepared by Oak Ridge National........................................................................................................................ 1-1 1.2 History of the Oak Ridge Reservation

  9. at Oak Ridge National Laboratory A Project of

    E-Print Network [OSTI]

    ! #12;National Energy Security Center Halcyon Commercialization Center From a Single Office to an EntireOak Ridge at Oak Ridge National Laboratory A Project of One of the Community Reuse Organization Building... ...Partnerships with Oak Ridge National Laboratory have Never Been Easier! The Design Phase I

  10. Oak Ridge Site | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergyTher i nAand DOEDepartmentNew2008Group,OAK RIDGE, Tenn.Use |Oak

  11. Oak Ridge Office of Environmental Management

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak of EnvironmentalY-12Oak

  12. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak Ridge Site

  13. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak Ridge

  14. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak Ridge3:

  15. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak Ridge3:4:

  16. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak

  17. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak4 Annual

  18. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak4

  19. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak41, 2015

  20. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak41,

  1. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite SpecificOak41,Tuesday,

  2. Oak Ridge National Laboratory | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on DeliciousMathematicsEnergyInterested Parties -DepartmentAvailable forSite |n t787ORDER NO.ORSSABOUOOak RidgeOakOak

  3. INCREASED FLEXIBILITY OF TURBO-COMPRESSORS IN NATURAL GAS TRANSMISSION THROUGH DIRECT SURGE CONTROL

    SciTech Connect (OSTI)

    Robert J. McKee; Danny M. Deffenbaugh

    2004-12-01

    This annual progress report describes the third year's technical progress in a three-year program. This report introduces the benefits of improved surge detection and summarizes what is known about internal flows as surge precursors in centrifugal compressors. Early research results and findings concerning surge in centrifugal compressors and possible precursors to surge are presented. Laboratory test results in modern compressors with 3D impellers are described in detail and used to show the changes in internal flow patterns that occur as a compressor approaches surge. It was found that older compressors with recessed impeller blading (2D geometry) do not have the same accessible flow patterns. The laboratory test results indicate a large increase in potential operating range for modern compressors. This annual report also presents results from the field testing conducted during the course of this third year. The field test results showed similar changes in the surge probe strain signals and the same type, although of less magnitude, of indication that the compressor is approaching surge. An algorithm for identifying the nearness of surge has been proposed and evaluated with the available data. This project is co-funded by the Gas Machinery Research Council (GMRC) and by Siemens Energy and Automation (Siemens). The results of the project include a step-by-step process for design, sizing, and installation of surge detection probes and for implementation of the direct surge control in centrifugal compressor controllers. This work is considered a step towards the successful implementation of direct surge control for improved flexibility and efficiency in natural gas transmission compressors.

  4. Rotor whirl forces induced by the tip clearance effect in axial flow compressors

    SciTech Connect (OSTI)

    Ehrich, F. )

    1993-10-01

    It is now widely recognized that destabilizing forces, tending to generate forward rotor whirl, are generated in axial flow turbines as a result of the nonuniform torque induced by the nonuniform tip-clearance in a deflected rotor--the so called Thomas/Alford force. It is also recognized that there will be a similar effect in axial flow compressors, but qualitative considerations cannot definitively establish the magnitude or even the direction of the induced whirling forces--that is, if they will tend to forward or backward whirl. Applying a parallel compressor model to simulate the operation of a compressor rotor deflected radially in its clearance, it is possible to derive a quantitative estimate of the proportionality factor [beta] which relates the Thomas/Alford force in axial flow compressors (i.e., the tangential force generated by a radial deflection of the rotor) to the torque level in the compressor. The analysis makes use of experimental data from the GE Aircraft Engines Low Speed Research Compressor facility comparing the performance of three different axial flow compressors, each with four stages (typical of a mid-block of an aircraft gas turbine compressor) at two different clearances. It is found that the value of [beta] is in the range of +0.27 to [minus]0.71 in the vicinity of the stages' nominal operating line and +0.08 to [minus]1.25 in the vicinity of the stages' operation at peak efficiency. The value of [beta] reaches a level of between [minus]1.16 and [minus]3.36 as the compressor is operated near its stalled condition.

  5. MA 15400 Spring 2015

    E-Print Network [OSTI]

    MA 15400 Spring 2015. Form 01. Name: PUID. ClassTime/Day Section Instructor Room. MWF 8:30 am 0021 Delworth, Tim SMITH 108. Online 0004 Delworth ...

  6. Geography 476 Spring Semester

    E-Print Network [OSTI]

    Frank, Thomas D.

    Geography 476 Spring Semester Instructor: Dr. Tom Frank Department of Geography l Director, Spatial both environmental and physical geography applications. You will create a PowerPoint presentation

  7. Towards development of an incipient surge detection device for centrifugal compressors 

    E-Print Network [OSTI]

    Hassinger, David Alan

    1978-01-01

    the centrifugal compressor does have a higher pressure ratio, the axial flow compressor has a The citations on the following pages follow the style of t. h ASME Jo 1 f E~ f po Surge Line / ( I I I I / / / / / / / ncreasin m 0 0 e '4 C4 8 0 D...TOWARDS DEVELOPMENT OF AN INCIPIENT SURGE DETECTION DEVICE FOR CENTRIFUGAL COMPRESSORS A Thesis DAVID ALAN HASSINGER Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree of MASTER...

  8. 241-U-701 new compressor building and instrument air piping analyses

    SciTech Connect (OSTI)

    Huang, F.H.

    1994-08-25

    Building anchorage analysis is performed to qualify the design of the new compressor building foundation given in the ECN ``241-U-701 New Compressor Building.`` Recommendations for some changes in the ECN are made accordingly. Calculations show that the 6-in.-slab is capable of supporting the pipe supports, and that the building foundation, air compressor and dryer anchorage, and electric rack are adequate structurally. Analysis also shows that the instrument air piping and pipe supports for the compressed air system meet the applicable code requirements and are acceptable. The building is for the U-Farm instrument air systems.

  9. Hydraulic accumulator-compressor for geopressured enhanced oil recovery

    DOE Patents [OSTI]

    Goldsberry, Fred L. (Spring, TX)

    1988-01-01

    A hydraulic accumulator-compressor vessel using geothermal brine under pressure as a piston to compress waste (CO.sub.2 rich) gas is used in a system having a plurality of gas separators in tandem to recover pipeline quality gas from geothermal brine. A first high pressure separator feeds gas to a membrance separator which separates low pressure waste gas from high pressure quality gas. A second separator produces low pressure waste gas. Waste gas from both separators is combined and fed into the vessel through a port at the top as the vessel is drained for another compression cycle. High pressure brine is then admitted into the vessel through a port at the bottom of the vessel. Check valves control the flow of low pressure waste gas into the vessel and high pressure waste gas out of the vessel.

  10. Stretchers and compressors for ultra-high power laser systems

    SciTech Connect (OSTI)

    Yakovlev, I V [Institute of Applied Physics, Russian Academy of Sciences, Nizhnii Novgorod (Russian Federation)

    2014-05-30

    This review is concerned with pulse stretchers and compressors as key components of ultra-high power laser facilities that take advantage of chirped-pulse amplification. The potentialities, characteristics, configurations and methods for the matching and alignment of these devices are examined, with particular attention to the history of the optics of ultra-short, ultra-intense pulses before and after 1985, when the chirped-pulse amplification method was proposed, which drastically changed the view of the feasibility of creating ultra-high power laser sources. The review is intended primarily for young scientists and experts who begin to address the amplification and compression of chirped pulses, experts in laser optics and all who are interested in scientific achievements in the field of ultra-high power laser systems. (review)

  11. EA-1117: Management of Spent Nuclear Fuel on the Oak Ridge Reservation, Oak Ridge, Tennessee

    Broader source: Energy.gov [DOE]

    This EA evaluates the environmental impacts of the proposal for the management of spent nuclear fuel on the U.S. Department of Energy's Oak Ridge Reservation to implement the preferred alternative...

  12. Introduction to the Oak Ridge Reservation 1-1 1. Introduction to the Oak Ridge Reservation

    E-Print Network [OSTI]

    Pennycook, Steve

    /remedial investigation reports, waste management characterization sampling data, and environmental permit compliance data sector business/industrial park; the Oak Ridge Institute for Science and Education (ORISE) South Campus

  13. Forging of compressor blades: Temperature and ram velocity effects

    SciTech Connect (OSTI)

    Saigal, A.; Zhen, K.; Chan, T.S.

    1995-07-01

    Forging is one of the most widely used manufacturing process for making high-strength, structurally integrated, impact and creep-resistant Ti-6Al-4V compressor blades for jet engines. In addition, in modern metal forming technology, finite element analysis method and computer modeling are being extensively employed for initial evaluation and optimization of various processes, including forging. In this study, DEFORM, a rigid viscoplastic two-dimensional finite element code was used to study the effects of initial die temperature and initial ram velocity on the forging process. For a given billet, die temperature and ram velocity influence the strain rate, temperature distribution,and thus the flow stress of the material. The die temperature and the ram velocity were varied over the range 300 to 700 F and 15--25 in./sec, respectively, to estimate the maximum forging load and the total energy required to forge compressor blades. The ram velocity was assumed to vary linearly as a function of stroke. Based on the analysis,it was found the increasing the die temperature from 300 to 700 F decreases the forging loads by 19.9 percent and increases the average temperature of the workpiece by 43 F. Similarly, increasing the initial ram velocity from 15 to 25 in./sec decreases the forging loads by 25.2 percent and increases the average temperature of the workpiece by 36 F. The nodal temperature distribution is bimodal in each case. The forging energy required to forge the blades is approximately 18 kips *in./in.

  14. Oak Ridge reservation land-use plan

    SciTech Connect (OSTI)

    Bibb, W. R.; Hardin, T. H.; Hawkins, C. C.; Johnson, W. A.; Peitzsch, F. C.; Scott, T. H.; Theisen, M. R.; Tuck, S. C.

    1980-03-01

    This study establishes a basis for long-range land-use planning to accommodate both present and projected DOE program requirements in Oak Ridge. In addition to technological requirements, this land-use plan incorporates in-depth ecological concepts that recognize multiple uses of land as a viable option. Neither environmental research nor technological operations need to be mutually exclusive in all instances. Unique biological areas, as well as rare and endangered species, need to be protected, and human and environmental health and safety must be maintained. The plan is based on the concept that the primary use of DOE land resources must be to implement the overall DOE mission in Oak Ridge. This document, along with the base map and overlay maps, provides a reasonably detailed description of the DOE Oak Ridge land resources and of the current and potential uses of the land. A description of the land characteristics, including geomorphology, agricultural productivity and soils, water courses, vegetation, and terrestrial and aquatic animal habitats, is presented to serve as a resource document. Essentially all DOE land in the Oak Ridge area is being fully used for ongoing DOE programs or has been set aside as protected areas.

  15. Oak Ridge Reservation Waste Management Plan

    SciTech Connect (OSTI)

    Turner, J.W. [ed.

    1995-02-01

    This report presents the waste management plan for the Oak Ridge Reservation facilities. The primary purpose is to convey what facilities are being used to manage wastes, what forces are acting to change current waste management systems, and what plans are in store for the coming fiscal year.

  16. Motor Gasoline Assessment, Spring 1997

    Reports and Publications (EIA)

    1997-01-01

    Analyzes the factors causing the run up of motor gasoline prices during spring 1996 and the different market conditions during spring 1997 that caused prices to decline.

  17. Effects of rotor tip blade loading variation on compressor stage performance

    E-Print Network [OSTI]

    Tiralap, Aniwat

    2015-01-01

    Changes in loss generation associated with altering the rotor tip loading of an embedded compressor stage is assessed. Steady and unsteady three-dimensional computations, complemented by control volume analyses, for varying ...

  18. Optimal Design and Tolerancing of Compressor Blades Subject to Manufacturing Variability

    E-Print Network [OSTI]

    Wang, Qiqi

    This paper presents a computational approach for optimal robust design and tolerancing of turbomachinery compressor blades that are subject to geometric variability. This approach simultaneously determines the optimal blade ...

  19. Adjustable Speed- A Tool for Saving Energy Losses in Pumps, Fans, Fans, Blowers and Compressors 

    E-Print Network [OSTI]

    Hickok, H. N.

    1985-01-01

    Petroleum and chemical plants of today are effectively cutting energy losses in their plants thermally, electrically, and mechanically in their process equipment. In rotating process equipment such as pumps, fans, compressors, and blowers, much...

  20. Forced response of a centrifugal compressor stage due to the impeller-diffuser interaction

    E-Print Network [OSTI]

    Walton, Edward James

    2014-01-01

    The unsteady pressure field experienced by a centrifugal compressor stage can be dominated by of the impeller-diffuser interaction. The energy of the unsteady field, under certain aerodynamic and structural conditions, is ...

  1. Effects of upstream wake phasing on the performance of transonic compressors

    E-Print Network [OSTI]

    Nolan, Sean Patrick Rock

    2009-01-01

    The effect of the upstream wake phase on the work input (i.e., rise in stagnation enthalpy across the blade row) of a transonic rotor is examined computationally and analytically. It is found that the compressor work depends ...

  2. Impact of unsteady flow processes on the performance of a high speed axial flow compressor

    E-Print Network [OSTI]

    Botros, Barbara Brenda

    2008-01-01

    This thesis examines the unsteady interactions between blade rows in a high Mach number, highly-loaded compressor stage. Two straight vane/rotor configurations with different axial spacing between vane and rotor are ...

  3. Discharge characteristics and dynamics of compressive plasma streams generated by a compact magnetoplasma compressor

    SciTech Connect (OSTI)

    Garkusha, I. E.; Tereshin, V. I.; Chebotarev, V. V.; Solyakov, D. G.; Petrov, Yu. V.; Ladygina, M. S.; Marchenko, A. K.; Staltsov, V. V.; Yelisyeyev, D. V. [National Academy of Sciences of Ukraine, Institute of Plasma Physics, National Science Center 'Kharkiv Institute of Physics and Technology,' (Ukraine)

    2011-11-15

    Results from experimental studies of a compact magnetoplasma compressor designed for operation with heavy gases are presented. The integral characteristics of the discharge and the energy contents and other parameters of the generated xenon plasma streams are determined.

  4. Effect of circumferential groove casing treatment parameters on axial compressor flow range

    E-Print Network [OSTI]

    Hanley, Brian K. (Brian Kyle)

    2010-01-01

    The impact on compressor flow range of circumferential casing grooves of varying groove depth, groove axial location, and groove axial extent is assessed against that of a smooth casing wall using computational experiments. ...

  5. Development of a transonic front stage of an axial flow compressor for industrial gas turbines

    SciTech Connect (OSTI)

    Katoh, Y.; Ishii, H.; Tsuda, Y.; Yanagida, M. . Mechanical Engineering Research Lab.); Kashiwabara, Y. . Dept. of Mechanical Systems Engineering)

    1994-10-01

    This paper describes the aerodynamic blade design of a highly loaded three-stage compressor, which is a model compressor for the front stage of an industrial gas turbine. Test results are presented that confirm design performance. Some surge and rotating stall measurement results are also discussed. The first stator blade in this test compressor operates in the high subsonic range at the inlet. To reduce the pressure loss due to blade surface shock waves, a shock-free airfoil is designed to replace the first stator blade in an NACA-65 airfoil in a three-stage compressor. Comparison of the performance of both blades shows that the shock-free airfoil blade reduces pressure loss. This paper also presents some experimental results for MCA (multicircular arc) airfoils, which are used for first rotor blades.

  6. Measurement of the three-dimensional tip region flow field in an axial compressor

    SciTech Connect (OSTI)

    Stauter, R.C. )

    1993-07-01

    A two-color, five-beam LDV system has been configured to make simultaneous three-component velocity measurements of the flow field in a two-stage axial compressor model. The system has been used to make time-resolved measurements both between compressor blade rows and within the rotating blade passages in an axial compressor. The data show the nature and behavior of the complex, three-dimensional flow phenomena present in the tip region of a compressor as the convect downstream. In particular, the nature of the tip leakage vortex is apparent, being manifested by high blockage as well as the expected vortical motion. The data indicate that the radial flows associated with the tip leakage vortex begin to decrease while within the rotor passage, and that they temporarily increase aft of the passage.

  7. Effects of rotor tip clearance on an embedded compressor stage performance

    E-Print Network [OSTI]

    Sakulkaew, Sitanun

    2012-01-01

    Compressor efficiency variation with rotor tip gap is assessed using numerical simulations on an embedded stage representative of that in a large industrial gas turbine with Reynolds number being approximately 2 x 106 to ...

  8. An improved blade passage model for estimating off-design axial compressor performance

    E-Print Network [OSTI]

    Brand, Maximilian Lewis

    2013-01-01

    Accurate estimates of multistage axial compressor performance at off-design operating conditions are essential to the determination of key performance metrics of aircraft gas turbine engines, such as fuel burn, thrust ...

  9. A novel design methodology for enhanced compressor performance based on a dynamic stability metric

    E-Print Network [OSTI]

    Castiella Ruiz de Velasco, Juan Carlos, 1978-

    2005-01-01

    (cont.) compressor design optimization framework allows a versatile definition of the objective function such that any combination of pressure ratio, efficiency and dynamic stability can be prescribed at various operating ...

  10. Three-dimensional rotating stall inception and effects of rotating tip clearance asymmetry in axial compressors

    E-Print Network [OSTI]

    Gordon, Kenneth A. (Kenneth Andrew), 1970-

    1999-01-01

    The effects of two types of flow nonuniformity on stall inception behavior were assessed with linearized stability analyses of two compressor flow models. Response to rotating tip clearance asymmetries induced by a whirling ...

  11. Characterization of the flow field response to vaneless space reduction in centrifugal compressors

    E-Print Network [OSTI]

    Villanueva V., Alfonso D. (Villanueva Villarreal)

    2006-01-01

    The unsteady three-dimensional flow field for two centrifugal compressors of nearly identical design (one with a marginally smaller impeller-diffuser gap) is interrogated to assess the difference in the time averaged ...

  12. Characterization of unsteady loading due to impeller-diffuser interaction in centrifugal compressors

    E-Print Network [OSTI]

    Lusardi, Christopher (Christopher Dean)

    2012-01-01

    Time dependent simulations are used to characterize the unsteady impeller blade loading due to imipeller-diffuser interaction in centrifugal compressor stages. The capability of simulations are assessed by comparing results ...

  13. Using Outside Air for Flooded Oil Screw Compressors at an Industrial Facility 

    E-Print Network [OSTI]

    Hunt, D. G.; Terry, S.

    2014-01-01

    A study has been performed to determine if inlet air temperature provides an increase in compressor efficiency, seen through reduced power for some specified mass flow. A theoretical analysis suggests that power is not a function of volumetric flow...

  14. Three-dimensional hybrid grid generator and unstructured flow solver for compressors and turbines 

    E-Print Network [OSTI]

    Kim, Kyusup

    2005-02-17

    . The Menter?s k ?? model is implemented to simulate the turbulence e?ects. The ?ow solver is validated against the analytical and experimental results. A parametric study is performed for a high speed centrifugal compressor....

  15. Stage effects on stalling and recovery of a high-speed 10-stage axial-flow compressor

    SciTech Connect (OSTI)

    Copenhaver, W.W.

    1988-01-01

    Results of a high-speed 10-stage axial-flow compressor test involving overall compressor and individual stage performance while stalling and operating in quasi-steady rotating stall are described. Test procedures and data-acquisition methods used to obtain the dynamic stalling and quasi-steady in-stall data are explained. Unstalled and in-stall time-averaged data obtained from the compressor operating at five different shaft speeds and one off-schedule variable vane condition are presented. Effects of compressor speed and variable geometry on overall compressor in-stall pressure rise and hysteresis extent are illustrated through the use of quasi-steady-stage temperature rise and pressure-rise characteristics. Results indicate that individual stage performance during overall compressor rotating stall operation varies considerably throughout the length of the compressor. The measured high-speed 10-stage test compressor individual stage pressure and temperature characteristics were input into a stage-by-stage dynamic compressor performance model. Comparison of the model results and measured pressures provided the additional validation necessary to demonstrate the model's ability to predict high-speed multistage compressor stalling and in-stall performance.

  16. Development of Versatile Compressor Modeling using Approximation Techniques for Alternative Refrigerants Evaluation

    SciTech Connect (OSTI)

    Abdelaziz, Omar; Shrestha, Som S

    2014-01-01

    Refrigerants are the life-blood of vapor compression systems that are widely used in Heating, Ventilation, Air-Conditioning, and Refrigeration (HVAC&R) applications. The HVAC&R community is currently transitioning from main-stream refrigerants that have high Global Warming Potential (GWP) to alternative lower-GWP refrigerants. During this transition, it is important to account for the life cycle climate performance of alternative refrigerants since their performance will be different than that of higher-GWP refrigerants. This requires the evaluation of the system performance with the new refrigerants. Unfortunately, it is extremely difficult to predict the realistic performance of new alternative refrigerants without experimental validation. One of the main challenges in this regard is modeling the compressor performance with high fidelity due to the complex interaction of operating parameters, geometry, boundary conditions, and fluid properties. High fidelity compressor models are computationally expensive and require significant pre-processing to evaluate the performance of alternative refrigerants. This paper presents a new approach to modeling compressor performance when alternative refrigerants are used. The new modeling concept relies on using existing compressor performance to create an approximate model that captures the dependence of compressor performance on key operating parameters and fluid properties. The model can be built using a myriad of approximation techniques. This paper focuses on Kriging-based techniques to develop higher fidelity approximate compressor models. Baseline and at least one alternative refrigerant performance data are used to build the model. The model accuracy was evaluated by comparing the model results with compressor performance data using other refrigerants. Preliminary results show that the approximate model can predict the compressor mass flow rate and power consumption within 5%.

  17. Tip clearance flows in axial compressors: stall inception and stability enhancement

    E-Print Network [OSTI]

    Weichert, Stephanie April

    2012-02-07

    and 91 figures. Part of this dissertation has been presented in the following publication: Weichert, S., Day, I. & Freeman, C. (2011) Self-Regulating Casing Treat- ment for Axial Compressor Stability Enhancement. Proceedings of ASME Turbo Expo 2011, June... -span if unspecified W Rotor Relative Flow Velocity, mid-span if unspecified xii Superscripts and Subscripts 0 Stagnation condition 1 Rotor inlet conditions 2 Rotor exit, stator inlet conditions 3 Stator exit conditions a1 Deverson compressor bellmouth inlet d2...

  18. Refrigeration system with a compressor-pump unit and a liquid-injection desuperheating line

    DOE Patents [OSTI]

    Gaul, Christopher J. (Thornton, CO)

    2001-01-01

    The refrigeration system includes a compressor-pump unit and/or a liquid-injection assembly. The refrigeration system is a vapor-compression refrigeration system that includes an expansion device, an evaporator, a compressor, a condenser, and a liquid pump between the condenser and the expansion device. The liquid pump improves efficiency of the refrigeration system by increasing the pressure of, thus subcooling, the liquid refrigerant delivered from the condenser to the expansion device. The liquid pump and the compressor are driven by a single driving device and, in this regard, are coupled to a single shaft of a driving device, such as a belt-drive, an engine, or an electric motor. While the driving device may be separately contained, in a preferred embodiment, the liquid pump, the compressor, and the driving device (i.e., an electric motor) are contained within a single sealable housing having pump and driving device cooling paths to subcool liquid refrigerant discharged from the liquid pump and to control the operating temperature of the driving device. In another aspect of the present invention, a liquid injection assembly is included in a refrigeration system to divert liquid refrigerant from the discharge of a liquid pressure amplification pump to a compressor discharge pathway within a compressor housing to desuperheat refrigerant vapor to the saturation point within the compressor housing. The liquid injection assembly includes a liquid injection pipe with a control valve to meter the volume of diverted liquid refrigerant. The liquid injection assembly may also include a feedback controller with a microprocessor responsive to a pressure sensor and a temperature sensor both positioned between the compressor to operate the control valve to maintain the refrigerant at or near saturation.

  19. Approaches Toward Achieving Optimum Efficiency in Rerates of Large Centrifugal Compressors 

    E-Print Network [OSTI]

    Rudisel, D. A.

    1996-01-01

    outcome. Figure 7 Case 3 Compressor Schematic Once the boundaries were established, and feasible methods of working within those constraints identified, the expected installed cost for the machine replacement was determined, and the project found... in the 10,000 to 50,000 horsepower range. When new, the machines are aerodynamically and mechanically designed and built to the state of the art as it exists at that time. However, these compressor casings are commonly rerated in later years when...

  20. Development of a dry linear compressor for GM and pulse tube cryocoolers

    E-Print Network [OSTI]

    Höhne, Jens

    2015-01-01

    Pressure Wave Systems GmbH has developed a dry compressor for GM and pulse tube cryocoolers. The concept is based on hydraulically driven metal bellows in which the Helium working gas is compressed. The system is operated in the region of 1 kW of electrical input power and has been successfully tested with a SHI RDK-101D GM cryocooler cold head. Set-up, performance and reliability of the compressor system will be discussed.

  1. Active stabilization of rotating stall in a three-stage axial compressor

    SciTech Connect (OSTI)

    Haynes, J.M.; Hendricks, G.J.; Epstein, A.H. . Gas Turbine Lab.)

    1994-04-01

    A three-stage, low-speed axial research compressor has been actively stabilized by damping low-amplitude circumferentially traveling waves, which can grow into rotating stall. Using a circumferential array of hot-wire sensors, and an array of high-speed individually positioned control vanes as the actuator, the first and second spatial harmonics of the compressor were stabilized down to a characteristic slope of 0.9, yielding an 8 percent increase in operating flow range. Stabilization of the third spatial harmonic did not alter the stalling flow coefficient. The actuators were also used open loop to determine the forced response behavior of the compressor. A system identification procedure applied to the forced response data then yielded the compressor transfer function. The Moore-Greitzer two-dimensional stability model was modified as suggested by the measurements to include the effect of blade row time lags on the compressor dynamics. This modified Moore-Greitzer model was then used to predict both the open and closed-loop dynamic response of the compressor. The model predictions agreed closely with the experimental results. In particular, the model predicted both the mass flow at stall without control and the design parameters needed by, and the range extension realized from, active control.

  2. Apparatus and methods for cooling and sealing rotary helical screw compressors

    DOE Patents [OSTI]

    Fresco, Anthony N. (P.O. Box 734, Upton, NY 11973)

    1997-01-01

    In a compression system which incorporates a rotary helical screw compressor, and for any type of gas or refrigerant, the working liquid oil is atomized through nozzles suspended in, and parallel to, the suction gas flow, or alternatively the nozzles are mounted on the suction piping. In either case, the aim is to create positively a homogeneous mixture of oil droplets to maximize the effectiveness of the working liquid oil in improving the isothermal and volumetric efficiencies. The oil stream to be atomized may first be degassed at compressor discharge pressure by heating within a pressure vessel and recovering the energy added by using the outgoing oil stream to heat the incoming oil stream. The stripped gas is typically returned to the compressor discharge flow. In the preferred case, the compressor rotors both contain a hollow cavity through which working liquid oil is injected into channels along the edges of the rotors, thereby forming a continuous and positive seal between the rotor edges and the compressor casing. In the alternative method, working liquid oil is injected either in the same direction as the rotor rotation or counter to rotor rotation through channels in the compressor casing which are tangential to the rotor edges and parallel to the rotor centerlines or alternatively the channel paths coincide with the helical path of the rotor edges.

  3. Apparatus and methods for cooling and sealing rotary helical screw compressors

    DOE Patents [OSTI]

    Fresco, A.N.

    1997-08-05

    In a compression system which incorporates a rotary helical screw compressor, and for any type of gas or refrigerant, the working liquid oil is atomized through nozzles suspended in, and parallel to, the suction gas flow, or alternatively the nozzles are mounted on the suction piping. In either case, the aim is to create positively a homogeneous mixture of oil droplets to maximize the effectiveness of the working liquid oil in improving the isothermal and volumetric efficiencies. The oil stream to be atomized may first be degassed at compressor discharge pressure by heating within a pressure vessel and recovering the energy added by using the outgoing oil stream to heat the incoming oil stream. The stripped gas is typically returned to the compressor discharge flow. In the preferred case, the compressor rotors both contain a hollow cavity through which working liquid oil is injected into channels along the edges of the rotors, thereby forming a continuous and positive seal between the rotor edges and the compressor casing. In the alternative method, working liquid oil is injected either in the same direction as the rotor rotation or counter to rotor rotation through channels in the compressor casing which are tangential to the rotor edges and parallel to the rotor center lines or alternatively the channel paths coincide with the helical path of the rotor edges. 14 figs.

  4. Hydrologic data summary for the White Oak Watershed at Oak Ridge National Laboratory, Oak Ridge, Tennessee, October 1990--December 1991

    SciTech Connect (OSTI)

    Borders, D.M.; Gregory, S.M.; Clapp, R.B.; Frederick, B.J.; Watts, J.A.

    1992-06-01

    This report summarizes for the 15-month period of October 1990-- December 1991 the available dynamic hydrologic data collected, primarily on the White Oak Creek (WOC) watershed, along with information collected on the surface flow systems that affect the quality or quantity of surface water. The collection of hydrologic data is one component of numerous, ongoing Oak Ridge National Laboratory (ORNL) environmental studies and monitoring programs and is intended to: (1) characterize the quantity and quality of water in the flow systems; (2) assist with the planning and assessment of remedial action activities; and, (3) provide long-term availability of data and quality assurance. Characterization of the hydrology of the WOC watershed is critical for understanding the processes that drive contaminant transport in the watershed. Identification of spatial and temporal trends in hydrologic parameters and mechanisms that affect the movement of contaminants supports the development of interim corrective measures and remedial restoration alternatives. In addition, hydrologic monitoring supports long-term assessment of the effectiveness of remedial actions in limiting the transport of contaminants across Waste Area Grouping (WAG) boundaries and ultimately to the off-site environment. For these reasons, it is of paramount importance to the Environmental Restoration Program (ERP) to collect and report hydrologic data activities that contribute to the Site Investigations component of the ERP. (White Oak Creek is also referred to as ``Whiteoak`` Creek).

  5. Hydrologic data summary for the White Oak Watershed at Oak Ridge National Laboratory, Oak Ridge, Tennessee, October 1990--December 1991

    SciTech Connect (OSTI)

    Borders, D.M.; Gregory, S.M.; Clapp, R.B.; Frederick, B.J.; Watts, J.A.

    1992-06-01

    This report summarizes for the 15-month period of October 1990-- December 1991 the available dynamic hydrologic data collected, primarily on the White Oak Creek (WOC) watershed, along with information collected on the surface flow systems that affect the quality or quantity of surface water. The collection of hydrologic data is one component of numerous, ongoing Oak Ridge National Laboratory (ORNL) environmental studies and monitoring programs and is intended to: (1) characterize the quantity and quality of water in the flow systems; (2) assist with the planning and assessment of remedial action activities; and, (3) provide long-term availability of data and quality assurance. Characterization of the hydrology of the WOC watershed is critical for understanding the processes that drive contaminant transport in the watershed. Identification of spatial and temporal trends in hydrologic parameters and mechanisms that affect the movement of contaminants supports the development of interim corrective measures and remedial restoration alternatives. In addition, hydrologic monitoring supports long-term assessment of the effectiveness of remedial actions in limiting the transport of contaminants across Waste Area Grouping (WAG) boundaries and ultimately to the off-site environment. For these reasons, it is of paramount importance to the Environmental Restoration Program (ERP) to collect and report hydrologic data activities that contribute to the Site Investigations component of the ERP. (White Oak Creek is also referred to as Whiteoak'' Creek).

  6. ORNL (Oak Ridge National Laboratory) 89

    SciTech Connect (OSTI)

    Anderson, T.D.; Appleton, B.R.; Jefferson, J.W.; Merriman, J.R.; Mynatt, F.R.; Richmond, C.R.; Rosenthal, M.W.

    1989-01-01

    This is the inaugural issues of an annual publication about the Oak Ridge National Laboratory. Here you will find a brief overview of ORNL, a sampling of our recent research achievements, and a glimpse of the directions we want to take over the next 15 years. A major purpose of ornl 89 is to provide the staff with a sketch of the character and dynamics of the Laboratory.

  7. Spring 2014 Pedal power

    E-Print Network [OSTI]

    rights art project 17 Aero girl unveiled 20 In memoriam Peter Smith 22 University news At the chalk face Wylie ­ and former aero girl exploring the potential of digital games spring watch on campus Cover photo

  8. Willows in the Spring

    E-Print Network [OSTI]

    Hill, DaMaris B.

    2012-05-31

    gestational period of adolescence. It fictionalizes the oppressions and opportunities that emerged as a result of the Women's Suffrage Movement in the United States. Inspired by the glorious achievements of women in Kansas' history, Willows in the Spring is a...

  9. AESP Spring Conference

    Broader source: Energy.gov [DOE]

    The Association of Energy Services Professionals (AESP) is hosting its annual Spring Conference in Portland, Oregon, where attendees can hear from experts on the critical role technology and effective implementation play in energy efficiency programs.

  10. Compressor Calorimeter Test of R-404A Alternatives ARM-31a, D2Y-65, L-40, and R32 + R-134a Mixture using a Scroll Compressor

    SciTech Connect (OSTI)

    Shrestha, Som S [ORNL; Sharma, Vishaldeep [ORNL; Abdelaziz, Omar [ORNL

    2013-08-01

    As a contribution to the AHRI Low-GWP Alternative Refrigerants Evaluation Program (AREP), this study compares the performance of four lower-GWP alternative refrigerants, ARM-31a, D2Y-65, L-40, and R-32 + R-134a mixture, to that of refrigerant R-404A (baseline) in a scroll compressor designed for medium temperature refrigeration applications. These comparisons were carried out via compressor calorimeter tests performed on a compressor designed for refrigerant R-404A and having a nominal rated capacity of 23,500 Btu/hr. Tests were conducted over a suction dew point temperature range of -10 F to 35 F in 5 F increments and a discharge dew point temperature range of 70 F to 140 F in 10 F increments. All the tests were performed with 20 F superheat, 40 F superheat, and 65 F suction temperature. A liquid subcooling level of 10 F to 15 F was maintained for all the test conditions. However, the cooling capacities reported in this study are normalized for 0 F subcooling. The tests showed that the compressor energy efficiency ratio (EER) and cooling capacity with all four alternative refrigerants tested are higher at higher saturation suction and saturation discharge temperature and lower at lower saturation suction and saturation discharge temperature, compared to that of R-404A. Discharge temperatures of all the alternative refrigerants were higher than that of R-404A at all test conditions.

  11. Spring 2013 National Transportation Stakeholders Forum Meeting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Stakeholders Forum Spring 2013 National Transportation Stakeholders Forum Meeting, New York Spring 2013 National Transportation Stakeholders Forum Meeting, New York Spring...

  12. Transuranic Waste Processing Center Oak Ridge Site Specific...

    Office of Environmental Management (EM)

    Transuranic Waste Processing Update Oak Ridge Site Specific Advisory Board May 14, 2014 Laura Wilkerson, Portfolio Federal Project Director Karen Deacon, Deputy Federal Project...

  13. Recommendation 169: Establishment of an Oak Ridge Oral History Program

    Broader source: Energy.gov [DOE]

    The ORSSAB recommends DOE-ORO fully endorse the establishment of an Oak Ridge Oral History Program and provide necessary assistance.

  14. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    Deiterding, Ralf

    Laboratory Oak Ridge, Tennessee SIAM Conference on Computational Science and Engineering Costa Mesa version with extended higher-order capabilities and large number of Riemann solvers - Hydrid WENO

  15. Independent Oversight Review, Oak Ridge Transuranic Waste Processing...

    Energy Savers [EERE]

    results of an independent oversight review of the management of safety significant structures, systems, and components at the Oak Ridge Transuranic Waste Processing Center...

  16. Oak Ridge Removes Laboratory's Greatest Source of Groundwater...

    Energy Savers [EERE]

    Removes Laboratory's Greatest Source of Groundwater Contamination Oak Ridge Removes Laboratory's Greatest Source of Groundwater Contamination May 1, 2012 - 12:00pm Addthis Workers...

  17. Oak Ridge Reservation Compliance Order, September 26, 1995 Summary

    Office of Environmental Management (EM)

    Oak Ridge Reservation Compliance Order, September 26, 1995 State Tennessee Agreement Type Compliance Order Legal Driver(s) FFCAct Scope Summary Enforce the Plan and ensure that the...

  18. Welcome - Energy Storage Research at Oak Ridge National Laboratory...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Physical Sciences Directorate ORNL Energy Storage Research at Oak Ridge National Laboratory Home Research Areas R&D Capabilities Partners & Sponsors Selected Publications & Patents...

  19. Oak Ridge Environmental Management Program Completes Work at...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (DOE) Oak Ridge Environmental Management (EM) program recently completed upgrades and soil remediation work at the Bethel Valley Burial Grounds, using approximately 17.5 million...

  20. Oak Ridge to acquire next generation supercomputer | ornl.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    McCorkle Communications and Media Relations (865) 574-7308 Oak Ridge to acquire next generation supercomputer Supercomputer simulations enable researchers to address the most...

  1. Food and Drug Administration White Oak Campus Environmental Stewardshi...

    Energy Savers [EERE]

    Stewardship and Cost Savings FEMP ESPC Success Story on water conservation and green energy at the Food and Drug Administration (FDA) White Oak Campus. PDF icon...

  2. Oak Ridge National Laboratory's Waste Diversion Efforts, OAS...

    Broader source: Energy.gov (indexed) [DOE]

    via the Pollution Prevention Tracking and Reporting System. The Oak Ridge National Laboratory (ORNL) Pollution Prevention Program (Program) plays a vital role in the Department's...

  3. DOE Issues Final Request for Proposal for Oak Ridge Transuranic...

    Broader source: Energy.gov (indexed) [DOE]

    from the Oak Ridge National Laboratory; and processing Nuclear Fuel Services soils. Similar services are currently being performed with Wastren Advantage, Inc. The...

  4. ORIGINAL PAPER Environmental change in Garry oak (Quercus garryana)

    E-Print Network [OSTI]

    Gedalof, Ze'ev

    . In this paper we take a multidisciplinary approach (bio- geography, paleoecology, dendrochronology Indigenous people land practices Á Paleoecology Introduction Understanding the complex nature of Garry oak

  5. Energy Department's Oak Ridge National Laboratory Unveils New...

    Office of Environmental Management (EM)

    website. Administered by the Department's Oak Ridge National Laboratory (ORNL), the new site, buildings.ideascale.com, will help technology innovators collect, share and...

  6. ORO Verification of Employment Tracking System(VETS) PIA, Oak...

    Energy Savers [EERE]

    System and Visitor Control System PIA, Oak Ridge Operations Office Occupational Medicine - Assistant PIA, Idaho National Laboratory Freedom of Information and Privacy Act...

  7. Oak Ridge National Laboratory Carbon Fiber Technology Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oak Ridge National Laboratory Carbon Fiber Technology Facility Low-Cost Carbon Fiber | Proposal Guidelines Proposal Guidelines Proposals should be no more than 5 single spaced...

  8. Oak Ridge National Laboratory Analysis of Waste Isolation Pilot...

    Office of Environmental Management (EM)

    event. This document corresponds to Appendix C: Analysis Integrated Summary Report of the Technical Assessment Team Report. Oak Ridge National Laboratory Analysis of Waste...

  9. Former Oak Ridge Bechtel Jacobs Employee Charged with Violating...

    Energy Savers [EERE]

    Atomic Energy Act Former Oak Ridge Bechtel Jacobs Employee Charged with Violating Atomic Energy Act Department of Justice press release announcing that a federal grand jury in the...

  10. ORIS: the Oak Ridge Imaging System program listings. [Nuclear...

    Office of Scientific and Technical Information (OSTI)

    program listings. Nuclear medicine imaging with rectilinear scanner and gamma camera Citation Details In-Document Search Title: ORIS: the Oak Ridge Imaging System program...

  11. Blue oak stump sprouting evaluated after firewood harvest in northern Sacramento Valley

    E-Print Network [OSTI]

    Standiford, Richard B.; McCreary, Douglas D.; Barry, Sheila J; Forero, Larry C.

    2011-01-01

    TABLE 4. Inventory data for blue oak thinning project in8. Standiford RB. 1997. Growth of blue oak on California’s2008. Stump sprouting of blue oaks 19 years after harvest.

  12. PRESOLICITATION Category: A. Owner: Department of Energy, Oak Ridge National Laboratory -UT Battelle LLC (DOE Contractor), Oak Ridge National Laboratory, Bethel

    E-Print Network [OSTI]

    Hively, Lee M.

    PRESOLICITATION Category: A. Owner: Department of Energy, Oak Ridge National Laboratory - UT Battelle LLC (DOE Contractor), Oak Ridge National Laboratory, Bethel Valley Road P.O. Box 2008, Oak Ridge-Battelle), the management and operating contractor for the United States Department of Energy's Oak Ridge National

  13. INCREASED FLEXIBILITY OF TURBO-COMPRESSORS IN NATURAL GAS TRANSMISSION THROUGH DIRECT SURGE CONTROL

    SciTech Connect (OSTI)

    Robert J. Mckee; Danny M. Deffenbaugh

    2003-12-01

    This annual progress report describes the second year's technical progress in a three-year program. This report summarizes what is known about internal flows as surge precursors in centrifugal compressors and focuses on accessing factors that affect pre-surge detection. An attempt is made in this analysis to identify and quantify factors concerning compressor design and operations that affect the detection of pre-surge conditions. This progress report presents results from recent laboratory tests conducted during the course of this second year. This project is co-funded by the Gas Machinery Research Council (GMRC) and by Siemens Energy and Automation (Siemens). The most recently available measured pre-surge internal flow data is parameterized to help identify factors that affect the indications that a compressor is approaching surge. Theoretical arguments are applied to access the factors that influence surge precursors and surge initiation in different centrifugal compressors. This work is considered a step in accessing the factors that affect the success or limitations of pre-surge detection in natural gas pipeline compressors.

  14. INCREASED FLEXIBILITY OF TURBO-COMPRESSORS IN NATURAL GAS TRANSMISSION THROUGH DIRECT SURGE CONTROL

    SciTech Connect (OSTI)

    Robert J. McKee; Shane P. Siebenaler; Danny M. Deffenbaugh

    2005-02-25

    The objective of this Direct Surge Control project was to develop a new internal method to avoid surge of pipeline compressors. This method will safely expand the range and flexibility of compressor operations, while minimizing wasteful recycle flow at the lower end of the operating envelope. The approach is to sense the onset of surge with a probe that directly measures re-circulation at the impeller inlet. The signals from the probe are used by a controller to allow operation at low flow conditions without resorting to a predictive method requiring excessive margin to activate a recycle valve. The sensor developed and demonstrated during this project was a simple, rugged, and sensitive drag probe. Experiments conducted in a laboratory compressor clearly showed the effectiveness of the technique. Subsequent field demonstrations indicated that the increase in range without the need to recycle flow was on the order of 19% to 25%. The cost benefit of applying the direct surge control technology appears to be as much as $120 per hour per compressor for operation without the current level of recycle flow. This could amount to approximately $85 million per year for the U.S. Natural Gas Transmission industry, if direct surge control systems are applied to most pipeline centrifugal compressors.

  15. A study of spike and modal stall phenomena in a low-speed axial compressor

    SciTech Connect (OSTI)

    Camp, T.R.; Day, I.J.

    1998-07-01

    This paper presents a study of stall inception mechanisms in a low-speed axial compressor. Previous work has identified two common flow breakdown sequences, the first associated with a short length-scale disturbance known as a spike, and the second with a longer length-scale disturbance known as a modal oscillation. In this paper the physical differences between these two mechanisms are illustrated with detailed measurements. Experimental results are also presented that relate the occurrence of the two stalling mechanisms to the operating conditions of the compressor. It is shown that the stability criteria for the two disturbances are different: Long length-scale disturbances are related to a two-dimensional instability of the whole compression system, while short length-scale disturbances indicate a three-dimensional breakdown of the flow-field associated with high rotor incidence angles. Based on the experimental measurements, a simple model is proposed that explains the type of stall inception pattern observed in a particular compressor. Measurements from a single-stage low-speed compressor and from a multistage high-speed compressor are presented in support of the model.

  16. Dynamic control of rotating stall in axial flow compressors using aeromechanical feedback

    SciTech Connect (OSTI)

    Gysling, D.L.; Greitzer, E.M.

    1995-07-01

    Dynamic control of rotating stall in an axial flow compressor has been implemented using aeromechanical feedback. The control strategy developed used an array of wall jets, upstream of a single-stage compressor, which were regulated by locally reacting reed valves. These reed valves responded to the small-amplitude flow-field pressure perturbations that precede rotating stall. The valve design was such that the combined system, compressor plus reed valve controller, was stable under operating conditions that had been unstable without feedback. A 10 percent decrease in the stalling flow coefficient was obtained using the control strategy, and the extension of stall flow range was achieved with no measurable change in the steady-state performance of the compression system. The experiments demonstrate the first use of aeromechanical feedback to extend the stable operating range of an axial flow compressor, and the first use of local feedback and dynamic compensation techniques to suppress rotating stall. The design of the experiment was based on a two-dimensional stall inception model, which incorporated the effect of the aeromechanical feedback. The physical mechanism for rotating stall in axial flow compressors was examined with focus on the role of dynamic feedback in stabilizing compression system instability. As predicted and experimentally demonstrated, the effectiveness of the aeromechanical control strategy depends on a set of nondimensional control parameters that determine the interaction of the control strategy and the rotating stall dynamics.

  17. Oak Ridge Reservation Compliance Summary 2-1 2. Oak Ridge Reservation Compliance Summary

    E-Print Network [OSTI]

    Pennycook, Steve

    .3.5 The Clean Water Act (CWA) seeks to improve surface water quality by establishing standards and a system disposal sites The Oak Ridge Reservation (ORR) has been on the U.S. Environmental Protection Agency (EPA pollutants through permits and air quality limits. Emissions of radionuclides are regulated by EPA via

  18. Development of a Hybrid Compressor/Expander Module for Automotive Fuel Cell Applications

    SciTech Connect (OSTI)

    McTaggart, Paul

    2004-12-31

    In this program TIAX LLC conducted the development of an advanced technology compressor/expander for supplying compressed air to Proton Exchange Membrane (PEM) fuel cells in transportation applications. The overall objective of this program was to develop a hybrid compressor/expander module, based on both scroll and high-speed turbomachinery technologies, which will combine the strengths of each technology to create a concept with superior performance at minimal size and cost. The resulting system was expected to have efficiency and pressure delivery capability comparable to that of a scroll-only machine, at significantly reduced system size and weight when compared to scroll-only designs. Based on the results of detailed designs and analyses of the critical system elements, the Hybrid Compressor/Expander Module concept was projected to deliver significant improvements in weight, volume and manufacturing cost relative to previous generation systems.

  19. A Five-Leg Inverter for Driving a Traction Motor and a Compressor Motor

    SciTech Connect (OSTI)

    Su, Gui-Jia; Hsu, John S

    2006-01-01

    This paper presents an integrated inverter for speed control of a traction motor and a compressor motor to reduce the compressor drive cost in EV/HEV applications. The inverter comprises five phase-legs; three of which are for control of a three-phase traction motor and the remaining two for a two-phase compressor motor with three terminals. The common terminal of the two-phase motor is tied to the neutral point of the three-phase traction motor to eliminate the requirement of a third phase leg. Further cost savings are made possible by sharing the switching devices, dc bus filter capacitors, gate drive power supplies, and control circuit. Simulation and experimental results are included to verify that speed control of the two motors is independent from each other.

  20. Flow Integrating Section for a Gas Turbine Engine in Which Turbine Blades are Cooled by Full Compressor Flow

    SciTech Connect (OSTI)

    Steward, W. Gene

    1999-11-14

    Routing of full compressor flow through hollow turbine blades achieves unusually effective blade cooling and allows a significant increase in turbine inlet gas temperature and, hence, engine efficiency. The invention, ''flow integrating section'' alleviates the turbine dissipation of kinetic energy of air jets leaving the hollow blades as they enter the compressor diffuser.

  1. Improving performance and rotordynamic characteristics of injection compressors via much longer balance-piston and division-wall seals 

    E-Print Network [OSTI]

    Rodrigues Rodrigues, Margarita

    2009-05-15

    Predictions are presented for a selected compressor using longer hole-pattern seals with L/D ratios from 0.5 to 2.5. Results were obtained for back-to-back and in-line compressors with the seal located at mid-span and at ...

  2. Oak Ridge, Tennessee, Warehouses Site Fact Sheet

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield Municipal Gas &SCE-SessionsSouth DakotaRobbins and700 GJO-2003-411-TAC GJO-PIN~$ .,2,Oak Ridge,

  3. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite Specific

  4. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite Specific January 12,

  5. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite Specific January 12,

  6. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite Specific January 12,9,

  7. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite Specific January

  8. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite Specific January3

  9. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite Specific

  10. Oak Ridge Site Specific Advisory Board

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak ofSite

  11. Operating Oak Ridge's "Calutrons"

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass mapSpeeding access toOctober 1996Technologies /JuneOperating Oak Ridge's

  12. Oak Ridge Office of Environmental Management

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on DeliciousMathematicsEnergyInterested Parties -DepartmentAvailable forSite |n t787ORDER NO.ORSSABOUOOak Oak Ridge

  13. ORISE: Oak Ridge Sitewide Institutional Review Board

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEY UNIVERSE TheForensic ScienceHowNews ReleasesdiseaseOak Ridge

  14. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    development of new materials #12;OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY HistoricalOAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY Fusion Materials Research Steve Zinkle U. S. DEPARTMENT OF ENERGY Outline · Effects of neutron bombardment on structural materials - "Five

  15. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    McDonald, Kirk

    LABORATORY U. S. DEPARTMENT OF ENERGY Possible Alternative · Hg jet & magnet axis in vertical plane · MagnetOAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY Tilt Option Discussion Issues Van Graves Phone Conference Sept 22, 2004 #12;2 OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

  16. NUCLEAR SCIENCE AND TECHNOLOGY DIVISION OAK RIDGE NATIONAL LABORATORY

    E-Print Network [OSTI]

    McDonald, Kirk

    NUCLEAR SCIENCE AND TECHNOLOGY DIVISION OAK RIDGE NATIONAL LABORATORY U.S. DEPARTMENT OF ENERGY Upton, NY #12;2 NUCLEAR SCIENCE AND TECHNOLOGY DIVISION OAK RIDGE NATIONAL LABORATORY U.S. DEPARTMENT OF ENERGY Outline · Properties, Safety Limits · Background - SNS Target Test Facility · Installing Hg & New

  17. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    Pennycook, Steve

    -Supercritical Steam Service - Turbines Phil Maziasz Materials Science and Technology Division Oak Ridge National considered for A-USC steam turbine application Alloy Ni Cr Co Mo Nb Ti Al Mn Si C NI 105 bal 14.85 20.0 5 #12;OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY Increasing Steam Temperature and Pressure

  18. Oak Ridge National Laboratory Policy on Research Integrity

    E-Print Network [OSTI]

    Oak Ridge National Laboratory Policy on Research Integrity All researchers performing research for the Oak Ridge National Laboratory (ORNL) must conform to the highest standards scientific integrity includes avoidance of personal conflicts of interest (PCOI), and the appearance of PCOIs, arising from

  19. Oaks and Environmental Education1 Kay Antunez de Mayolo2

    E-Print Network [OSTI]

    may examine how the human use of a natural resource effects the integrity of a natural system management and conservation of our state's natural resources. 1 Presented at the Symposium on Oak Woodlands. These programs could serve as models for groups involving youth in oak education and resource enhancement

  20. Sudden Oak Death: Recent Developments on Trees in Europe1

    E-Print Network [OSTI]

    on rhododendron stock in Germany and the Netherlands in 1993 and the new Phytophthora believed to be the cause in Germany and the Netherlands led to surveys for the pathogen in nursery material, initially in the United on European beech. However, stems of mature Q. cerris (Turkey oak), Q. petraea (sessile oak), Nothofagus

  1. Stability analysis and testing of a train of centrifugal compressors for high pressure gas injection

    SciTech Connect (OSTI)

    Memmott, E.A. [Dresser-Rand Co., Olean, NY (United States)

    1999-07-01

    This paper describes the rotor dynamic stability analysis and the PTC-10 Class 1 test of a three body centrifugal compressor train for high pressure natural gas injection services. This train had a full load full pressure string test on hydrocarbon gases to a final discharge pressure of 500 BAR (7250 PSIA). Each compressor is of the back to back configuration, and is equipped with tilting pad seals, damper bearings, and a honeycomb labyrinth at the division wall with shunt holes. The driver is a gas turbine.

  2. High efficiency, low frequency linear compressor proposed for Gifford-McMahon and pulse tube cryocoolers

    SciTech Connect (OSTI)

    Höhne, Jens

    2014-01-29

    In order to reduce the amount of greenhouse gas emissions, which are most likely the cause of substantial global warming, a reduction of overall energy consumption is crucial. Low frequency Gifford-McMahon and pulse tube cryocoolers are usually powered by a scroll compressor together with a rotary valve. It has been theoretically shown that the efficiency losses within the rotary valve can be close to 50%{sup 1}. In order to eliminate these losses we propose to use a low frequency linear compressor, which directly generates the pressure wave without using a rotary valve. First results of this development will be presented.

  3. System for lubrication of a brake air compressor associated with a turbocharged internal combustion engine

    SciTech Connect (OSTI)

    Spencer, J.C.

    1992-10-13

    This patent describes a system for use with a vehicle which includes a turbocharged internal combustion engine having a lubricating system wherein lubricating oil from an engine oil reservoir is circulated within the engine and also to and from an associated brake system air compressor which supplies compressed air for operation of the vehicle air braking system. This patent describes improvement in passing supercharged air to an oil crankcase of the air compressor to cause lubricating oil to drain therefrom and return to the engine oil reservoir.

  4. EA-1779: Proposed Changes to the Sanitary Biosolids Land Application Program on the Oak Ridge Reservation, Oak Ridge, Tennessee

    Broader source: Energy.gov [DOE]

    This EA evaluates the environmental impacts of a proposal to amend (e.g., by changing setback requirements from surface water features and potential channels to groundwater) the Sanitary Biosolids Land Application Program at the Oak Ridge Reservation in Oak Ridge, Tennessee.

  5. White Oak Dam stability analysis. Volume I

    SciTech Connect (OSTI)

    Ahmed, S.B.

    1994-01-01

    A parametric study was conducted to evaluate the stability of the White Oak Dam (WOD) embankment and foundation. Slope stability analyses were performed for the upper and lower bound soil properties at three sections of the dam using the PCSTABL4 computer program. Minimum safety factors were calculated for the applicable seismic and static loading conditions. Liquefaction potential of the dam embankment and foundation solid during the seismic event was assessed by using simplified procedures. The WOD is classified as a low hazard facility and the Evaluation Basis Earthquake (EBE) is defined as an earthquake with a magnitude of m{sub b} = 5.6 and a Peak Ground Accelerator (PGA) of 0.13 g. This event is approximately equivalent to a Modified Mercalli Intensity of VI-VIII. The EBE is used to perform the seismic evaluation for slope stability and liquefaction potential. Results of the stability analyses and the liquefaction assessment lead to the conclusion that the White Oak Dam is safe and stable for the static and the seismic events defined in this study. Ogden Environmental, at the request of MMES, has checked and verified the calculations for the critical loading conditions and performed a peer review of this report. Ogden has determined that the WOD is stable under the defined static and seismic loading conditions and the embankment materials are in general not susceptible to liquefaction.

  6. ENERGY CONVERSION Spring 2011

    E-Print Network [OSTI]

    Bahrami, Majid

    , 5th Edition Michael J. Moran and Howard N. Shapiro, John Wiley and Sons Inc., New York, NY, 2004, John Willey 2010. 3) Alternative Energy Systems and Applications, by B.K. Hodge, John Willey 2010. 41 ENSC 461 ENERGY CONVERSION Spring 2011 Instructor: Dr. Majid Bahrami 4372 Email

  7. Air Pollution Spring 2010

    E-Print Network [OSTI]

    Pierce, Jeffrey

    ATS 555 Air Pollution Spring 2010 T Th 11:00 ­ 12:15, NESB 101 Instructor: Prof. Sonia Kreidenweis an understanding of types and sources of air pollution. 2. Examine concentrations of air pollutants and their effects on health and welfare. Review regulations governing air pollution. 3. Examine the meteorological

  8. Biochemistry 482 Spring 2009

    E-Print Network [OSTI]

    Vonessen, Nikolaus

    1 Biochemistry 482 Spring 2009 Instructor: Dr. Stephen Lodmell Class time/place: MWF 10:10-11:00am, to be arranged Phone: 243-6393 email: stephen.lodmell@umontana.edu Text: Garrett and Grisham Biochemistry, 3rd ed. (updated) Overview: The second semester of biochemistry builds on the foundation laid by BIOC481

  9. SPRING 2007 METRICSMECHANICAL ENGINEERING

    E-Print Network [OSTI]

    Li, Teng

    OF ENGINEERING, UNIVERSITY OF MARYLAND. Department Works Globally to Share Knowledge & Expertise IN THIS ISSUE: 2SPRING 2007 METRICSMECHANICAL ENGINEERING A. JAMES CLARK SCHOOL of ENGINEERING www.enme.umd.edu A NEWSLETTER FOR ALUMNI AND FRIENDS OF THE DEPARTMENT OF MECHANICAL ENGINEERING AT THE A. JAMES CLARK SCHOOL

  10. Spring 2015 Thermodynamics -2

    E-Print Network [OSTI]

    Virginia Tech

    Spring 2015 Thermodynamics - 2 As indicated in the adjacent figure, a steady- flow cogeneration: recirculating hot water and electricity. Steam flows at 200 kg/s into the cogeneration plant at 5 bar to the factory. b. [30 pts] Determine the rate of entropy production within the cogeneration plant. The plant

  11. Spring 2014 Thermodynamics -1

    E-Print Network [OSTI]

    Battaglia, Francine

    Spring 2014 Thermodynamics - 1 Consider an insulated (adiabatic) piston and cylinder arrangement. Confirm this statement using the second law of thermodynamics. (b) (20) She now wants to calculate the work done by the air on the piston by using the first law of thermodynamics. Do this. Draw a T

  12. Energy Matters - Spring 2002

    SciTech Connect (OSTI)

    2002-03-01

    Quarterly newsletter from DOE's Industrial Technologies Program to promote the use of energy-efficient industrial systems. The focus of the Spring 2002 Issue of Energy Matters focuses on premium energy efficiency systems, with articles on new gas technologies, steam efficiency, the Augusta Newsprint Showcase, and more.

  13. Weather Forecasting Spring 2014

    E-Print Network [OSTI]

    Hennon, Christopher C.

    ATMS 350 Weather Forecasting Spring 2014 Professor : Dr. Chris Hennon Office : RRO 236C Phone : 232 of atmospheric physics and the ability to include this understanding into modern numerical weather prediction agencies, forecast tools, numerical weather prediction models, model output statistics, ensemble

  14. Technical background information for the environmental and safety report, Volume 4: White Oak Lake and Dam

    SciTech Connect (OSTI)

    Oakes, T.W.; Kelly, B.A.; Ohnesorge, W.F.; Eldridge, J.S.; Bird, J.C.; Shank, K.E.; Tsakeres, F.S.

    1982-03-01

    This report has been prepared to provide background information on White Oak Lake for the Oak Ridge National Laboratory Environmental and Safety Report. The paper presents the history of White Oak Dam and Lake and describes the hydrological conditions of the White Oak Creek watershed. Past and present sediment and water data are included; pathway analyses are described in detail.

  15. Source document for waste area groupings at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Osborne, P.L.; Kuhaida, A.J., Jr.

    1996-09-01

    This document serves as a source document for Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and other types of documents developed for and pertaining to Environmental Restoration (ER) Program activities at Oak Ridge National Laboratory (ORNL). It contains descriptions of the (1) regulatory requirements for the ORR ER Program, (2) Oak Ridge Reservation (ORR) ER Program, (3) ORNL site history and characterization, and (4) history and characterization of Waste Area Groupings (WAGS) 1-20. This document was created to save time, effort, and money for persons and organizations drafting documents for the ER Program and to improve consistency in the documents prepared for the program. By eliminating the repetitious use of selected information about the program, this document will help reduce the time and costs associated with producing program documents. By serving as a benchmark for selected information about the ER Program, this reference will help ensure that information presented in future documents is accurate and complete.

  16. NOISE CONTROL METHODS FOR A RECIPROCATING AIR COMPRESSOR USED IN FUEL CELL AUXILIARY POWER UNIT (APU)

    E-Print Network [OSTI]

    Carver, Jeffrey C.

    NOISE CONTROL METHODS FOR A RECIPROCATING AIR COMPRESSOR USED IN FUEL CELL AUXILIARY POWER UNIT What is Fuel Cell APU? Why use APU? To reduce overall noise levels in a fuel cell auxiliary power unit (APU) Main Components Foundation Power source Microphones Spectrum analyzer Stack of fuel cells

  17. Bond Graph Modeling of Centrifugal Compressor System Nur Uddin and Jan Tommy Gravdahl

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    . A model of a compression system with recycle flow is derived in this work. 1. INTRODUCTION Compressors are widely applied in industries, for exam- ples in pipeline natural gas transportation system, extraction in oil fields, and process chemical and petrochemical plants [1]. A model of a compression system

  18. Two results on compressor surge control with disturbance rejection Jan Tommy Gravdahl and Olav Egeland

    E-Print Network [OSTI]

    Gravdahl, Jan Tommy

    ] that the surge model of 7], which was derived for an axial compression system and is going to be usedTwo results on compressor surge control with disturbance rejection Jan Tommy Gravdahl and Olav- bilities. First, constant disturbances are included in the Greitzer model, and adaptive backstepping is em

  19. Natural Gas Compressor Stations on the Interstate Pipeline Network: Developments Since 1996

    Reports and Publications (EIA)

    2007-01-01

    This special report looks at the use of natural gas pipeline compressor stations on the interstate natural gas pipeline network that serves the lower 48 states. It examines the compression facilities added over the past 10 years and how the expansions have supported pipeline capacity growth intended to meet the increasing demand for natural gas.

  20. Evolution of pulse shapes during compressor scans in a CPA system and control of electron

    E-Print Network [OSTI]

    Geddes, Cameron Guy Robinson

    Evolution of pulse shapes during compressor scans in a CPA system and control of electron Ti:sapphire laser pulses has been controlled by appropriate choice of the higher order spectral phase The delicate details of the envelope function of ultrashort light pulses (`pulse shape') play an important role

  1. OPTIMAL CONTROL EXPERIMENTATION OF COMPRESSION TRAJECTORIES FOR A LIQUID PISTON AIR COMPRESSOR

    E-Print Network [OSTI]

    Li, Perry Y.

    compressor is the critical part of a Compressed Air En- ergy Storage (CAES) system. Efficient and fast Storage (CAES) system for offshore wind turbine that has recently been proposed in [1,2]. In the proposed CAES system, high pressure (20-30MPa) compressed air is stored in a dual chamber storage vessel

  2. STUDY OF WORKING FLUID MIXTURES AND HIGH TEMPERATURE WORKING FLUIDS FOR COMPRESSOR DRIVEN SYSTEMS

    E-Print Network [OSTI]

    Oak Ridge National Laboratory

    Discussion 17 Heat transfer in condensation 19 References 20 3. SYSTEM ASPECTS OF HEAT PUMPS WITH NONAZEOTROPIC MIXTURES 23 Conclusions 32 4. RECENT DEVELOPMENTS IN THE FIELD OF HIGH TEMPERATURE HEAT PUMPS 33 study with finite heat exchanger areas and realistic compressor efficiencies 50 Industrial case 51 Space

  3. Reducing Air Compressor Work by Using Inlet Air Cooling and Dehumidification 

    E-Print Network [OSTI]

    Hardy, Mark James

    2011-02-22

    both vapor compression and absorption cycle chillers to cool and dehumidify the inlet air. The results show that the performance increases as much as 8 percent for the compressor system with absorption inlet cooling and as much as 5 percent when using...

  4. Site descriptions of environmental restoration units at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Kuhaida, A.J. Jr.; Parker, A.F.

    1997-02-01

    This report provides summary information on Oak Ridge National Laboratory (ORNL) Environmental Restoration (ER) sites as listed in the Oak Ridge Reservation Federal Facility Agreement (FFA), dated January 1, 1992, Appendix C. The Oak Ridge National Laboratory was built in 1943 as part of the World War II Manhattan Project. The original mission of ORNL was to produce and chemically separate the first gram-quantities of plutonium as part of the national effort to produce the atomic bomb. The current mission of ORNL is to provide applied research and development in support of the U.S. Department of Energy (DOE) programs in nuclear fusion and fission, energy conservation, fossil fuels, and other energy technologies and to perform basic scientific research in selected areas of the physical, life, and environmental sciences. ER is also tasked with clean up or mitigation of environmental impacts resulting from past waste management practices on portions of the approximately 37,000 acres within the Oak Ridge Reservation (ORR). Other installations located within the ORR are the Gaseous Diffusion Plant (K-25) and the Y-12 plant. The remedial action strategy currently integrates state and federal regulations for efficient compliance and approaches for both investigations and remediation efforts on a Waste Area Grouping (WAG) basis. As defined in the ORR FFA Quarterly Report July - September 1995, a WAG is a grouping of potentially contaminated sites based on drainage area and similar waste characteristics. These contaminated sites are further divided into four categories based on existing information concerning whether the data are generated for scoping or remedial investigation (RI) purposes. These areas are as follows: (1) Operable Units (OU); (2) Characterization Areas (CA); (3) Remedial Site Evaluation (RSE) Areas; and (4) Removal Site Evaluation (RmSE) Areas.

  5. Site descriptions of environmental restoration units at the Oak Ridge K-25 Site, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Goddard, P.L.; Legeay, A.J.; Pesce, D.S.; Stanley, A.M.

    1995-11-01

    This report, Site Descriptions of Environmental Restoration Units at the Oak Ridge K-25 Site, Oak Ridge, Tennessee, is being prepared to assimilate information on sites included in the Environmental Restoration (ER) Program of the K-25 Site, one of three major installations on the Oak Ridge Reservation (ORR) built during World War III as part of the Manhattan Project. The information included in this report will be used to establish program priorities so that resources allotted to the K-25 ER Program can be best used to decrease any risk to humans or the environment, and to determine the sequence in which any remedial activities should be conducted. This document will be updated periodically in both paper and Internet versions. Units within this report are described in individual data sheets arranged alphanumerically. Each data sheet includes entries on project status, unit location, dimensions and capacity, dates operated, present function, lifecycle operation, waste characteristics, site status, media of concern, comments, and references. Each data sheet is accompanied by a photograph of the unit, and each unit is located on one of 13 area maps. These areas, along with the sub-area, unit, and sub-unit breakdowns within them, are outlined in Appendix A. Appendix B is a summary of information on remote aerial sensing and its applicability to the ER program.

  6. Comprehensive Integrated Planning Process for the Oak Ridge Operations Sites

    SciTech Connect (OSTI)

    Bechtel Jacobs Company LLC; Lockheed Martin Energy Research Corporation; Lockheed Martin Energy Systems, Inc.

    1999-09-01

    This plan is intended to assist the U.S. Department of Energy (DOE) and contractor personnel in implementing a comprehensive integrated planning process consistent with DOE Order 430.1A, "Life Cycle Asset Management," and Oak Ridge Operations (ORO) Order 430 on sites under the jurisdiction of DOE-ORO. Those sites are the Oak Ridge Reservation, in Oak Ridge, Tennessee; the Paducah Gaseous Diffusion Plant, in Paducah, Kentucky; and the Portsmouth Gaseous Diffusion Plant, in Piketon, Ohio. DOE contractors at these sites are charged with developing and producing this plan, which is referred to as simply the Comprehensive Integrated Plan.

  7. Oak Ridge Reservation Environmental report for 1990

    SciTech Connect (OSTI)

    Wilson, A.R.

    1991-09-01

    The first two volumes of this report are devoted to a presentation of environmental data and supporting narratives for the US Department of Energy's (DOE's) Oak Ridge Reservation (ORR) and surrounding environs during 1990. Volume 1 includes all narrative descriptions, summaries, and conclusions and is intended to be a stand-alone'' report for the ORR for the reader who does not want to review in detail all of the 1990 data. Volume 2 includes the detailed data summarized in a format to ensure that all environmental data are represented in the tables. Narratives are not included in Vol. 2. The tables in Vol. 2 are addressed in Vol. 1. For this reason, Vol. 2 cannot be considered a stand-alone report but is intended to be used in conjunction with Vol. 1.

  8. Oak Ridge Reservation environmental report for 1989

    SciTech Connect (OSTI)

    Jacobs, V.A.; Wilson, A.R.

    1990-10-01

    The first two volumes of this report are devoted to a presentation of environmental data and supporting narratives for the US Department of Energy's (DOE's) Oak Ridge Reservation (ORR) and surrounding environs during 1989. Volume 1 includes all narrative descriptions, summaries, and conclusions and is intended to be a stand-alone'' report for the ORR for the reader who does not want to review in detail all of the 1989 data. Volume 2 includes the detailed data summarized in a format to ensure that all environmental data are represented in the tables. Narratives are not included in Vol. 2. The tables in Vol. 2 are addressed in Vol. 1. For this reason, Vol. 2 cannot be considered a stand-alone report but is intended to be used in conjunction with Vol. 1. 16 figs., 194 tabs.

  9. Effects of nonaxisymmetric tip clearance on axial compressor performance and stability

    SciTech Connect (OSTI)

    Graf, M.B.; Wong, T.S.; Greitzer, E.M.; Marble, F.E.; Tan, C.S.; Shin, H.W.; Wisler, D.C.

    1998-10-01

    The effects of circumferentially nonuniform tip clearance on axial compressor performance and stability have been investigated experimentally and analytically. A theoretical model for compressor behavior with nonaxisymmetric tip clearance has been developed and used to design a series of first-of-a-kind experiments on a four-stage, low-speed compressor. The experiments and computational results together show clearly the central physical features and controlling parameters of compressor response to nonaxisymmetric tip clearance. It was found that the loss in stall margin was more severe than that estimated based on average clearance. The stall point was, in fact, closer to that obtained with uniform clearance at the maximum clearance level. The circumferential length scale of the tip clearance (and accompanying flow asymmetry) was an important factor in determining the stall margin reduction. For the same average clearance, the loss in peak pressure rise was 50 percent higher for an asymmetry with fundamental wavelength equal to the compressor circumference than with wavelength equal to one-half the circumference. The clearance asymmetry had much less of an effect on peak efficiency; the measured maximum efficiency decrease obtained was less than 0.4 percent compared to the 8 percent decrease in peak pressure rise due to the asymmetric clearance. The efficiency penalty due to nonaxisymmetric tip clearance was thus close to that obtained with a uniform clearance at the circumferentially averaged level. The theoretical model accurately captured the decreases in both steady-state pressure rise and stable operating range which are associated with clearance asymmetry.

  10. A study of spring rates of dynamically loaded helical springs 

    E-Print Network [OSTI]

    Whitwell, Franklin Carroll

    1965-01-01

    . 4 28 30 33 6. Test Results for Spring No. 5 . 35 7. Test Results for Spring No. 6 38 8. Test Results for Spring No. 7 40 9. Dimensionless Values 41 10. Galvanometer Damping 42 LIST OF FIGURES Figure Page Overall View of Experimental... Apparatus 8 3. Recording Equipment and Potentiometer Type Calibrator . . 9 Loading Mechanism and Variable Speed Drive . . . . . . . . 10 4 ~ Rear View of Variable Speed Drive and Loading Mechanism Showing Arrangement of Pulleys, Belt, and Shaft...

  11. Oak Ridge National Laboratory: Recent Accomplishments and Challenges...

    Office of Environmental Management (EM)

    (ORNL) ETTP ORNL Y-12 City of Oak Ridge www.energy.govEM ORNL Scope MV: MSRE Salt Drain Tanks * Bethel Valley D&D and RA scope - 160 facilities - Isotope processing...

  12. OAK RIDGE NATIONAL LABORATORY U.S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    · ASME Standards and Technologies, LLC · Chemical Composite Coatings Intl · Columbia Gas · Hatch Moss Mac: Perform financial analyses and incorporate knowledge into codes and standards #12;6 OAK RIDGE NATIONAL

  13. DOE Awards Contract for Oak Ridge Transuranic Waste Processing...

    Energy Savers [EERE]

    - The U.S. Department of Energy (DOE) today announced the award of a contract to North Wind Solutions, LLC for waste processing services at the Oak Ridge Transuranic Waste...

  14. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY 1 Applied R&D of 1st and 2nd Generation 40 K and 80 K ­ A 1-Tesla HTS coil will be made with YBCO conductor, instrumented and tested

  15. Science and Technology at Oak Ridge National Laboratory

    SciTech Connect (OSTI)

    Mason, Thomas

    2012-11-01

    ORNL Director Thom Mason explains the groundbreaking work in neutron sciences, supercomputing, clean energy, advanced materials, nuclear research, and global security taking place at the Department of Energy's Office of Science laboratory in Oak Ridge, Tenn.

  16. Science and Technology at Oak Ridge National Laboratory

    ScienceCinema (OSTI)

    Mason, Thomas

    2013-02-25

    ORNL Director Thom Mason explains the groundbreaking work in neutron sciences, supercomputing, clean energy, advanced materials, nuclear research, and global security taking place at the Department of Energy's Office of Science laboratory in Oak Ridge, Tenn.

  17. 60 years of great science [Oak Ridge National Laboratory

    SciTech Connect (OSTI)

    None

    2003-01-01

    This issue highlights Oak Ridge National Laboratory's contributions in more than 30 areas of research and related activities during the past 60 years and provides glimpses of current activities that are carrying on this heritage.

  18. SURESH K.S. VANNAN Oak Ridge National Laboratory (ORNL)

    E-Print Network [OSTI]

    Post, Wilfred M.

    - Present Oak Ridge, TN, USA Job Functions · Manage tasks, staffing, finance, and reporting for NASA funded scientific activities (e.g. deforestation studies in Africa, environmental impact of oil exploration in Gabon

  19. Oak Ridge Site Specific Advisory Board Annual Meeting

    Office of Environmental Management (EM)

    by board). (EMS & B&P) Suggested by DOE. 5. Established an ORSSAB website on the new Internet platform that the Oak Ridge Environmental Management Program is now using. The new...

  20. Oak Ridge Site Specific Advisory Board * P.O...

    Office of Environmental Management (EM)

    TN 37831 Phone: 865-241-4583, 865-241-4584, 1-800-382-6938 * Fax: 865-574-3521 * Internet: www.oakridge.doe.govemssab Many Voices Working for the Community Oak Ridge Site...

  1. DOE/ORO/2119 Oak Ridge Reservation Annual Site

    E-Print Network [OSTI]

    Pennycook, Steve

    Laboratory East Tennessee Technology Park Electronic publisher Coordinating editor Graphic artist Sandi and by East Tennessee Technology Park P.O. Box 4699, Oak Ridge, TN 37831-4699 Managed by Bechtel Jacobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.3 CLIMATE

  2. The Oak Ridge Reservation Annual Site Environmental Report Summary, 2007

    SciTech Connect (OSTI)

    None, None

    2009-02-28

    The Oak Ridge Reservation Annual Site Environmental Report is prepared and published each year to inform the public of the environmental activities that take place on the reservation and in the surrounding areas. It is written to comply with DOE Order 231.1A, Environment, Safety, and Health Reporting. This document has been prepared to present the highlights of the Oak Ridge Reservation Annual Site Environmental Report 2007 in an easy-to-read, summary format.

  3. Proceedings of the 4th Fire in Eastern Oak Forests Conference 207GTR-NRS-P-102 GENESIS OF AN OAK-FIRE SCIENCE CONSORTIUM

    E-Print Network [OSTI]

    Proceedings of the 4th Fire in Eastern Oak Forests Conference 207GTR-NRS-P-102 GENESIS OF AN OAK-FIRE and to identify fire information needs of oak-dominated communities such as woodlands, forests, savannas through the Forest Service's Northern Research Station. Smaller groups such as the Fire Learning Network

  4. RCRA Facility Investigation report for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Wilson, R. C.; Lewis, K. K.

    1991-09-01

    This report presents data and information related to remedial investigation studies for Oak Ridge National Laboratory (ORNL). Information is included on a soil gas survey, surface radiological investigations of waste areas, and well installation for ground water monitoring. (CBS)

  5. OAK RIDGE NATIONAL LABORATORY RESULTS OF RADIOLOGICAL

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield Municipal Gas &SCE-SessionsSouthReport for the Weldon Spring,7=cr5rnP 7694 i+lJNew York,' ,92 7% d

  6. Oak Ridge Field O%ce

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield Municipal Gas &SCE-SessionsSouthReport for the Weldon Spring,7=cr5rnP 7694 i+lJNewS e TAugustDOC F

  7. Oak Ridge Operations PO. Box E

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield Municipal Gas &SCE-SessionsSouthReport for the Weldon Spring,7=cr5rnP 7694 i+lJNewS e TAugustDOC

  8. MA 154 Schedule, Spring 2004

    E-Print Network [OSTI]

    math

    2015-02-11

    MA 15400 MWF and Online Sections, Spring 2015. Click on Lesson ---PP to watch a recorded lesson in YouTube. Some lessons are divided into two parts, ...

  9. INDEPENDENT VERIFICATION OF THE CENTRAL CAMPUS AND SOUTHEAST LABORATORY COMPLEX BUILDING SLABS AT OAK RIDGE NATIONAL LABORATORY, OAK RIDGE, TENNESSEE

    SciTech Connect (OSTI)

    Weaver, Phyllis C.

    2012-07-24

    Oak Ridge Associated Universities/Oak Ridge Institute for Science and Education (ORAU/ORISE) has completed the independent verification survey of the Central Campus and Southeast Lab Complex Building Slabs. The results of this effort are provided. The objective of this verification survey was to provide independent review and field assessment of remediation actions conducted by SEC, and to independently assess whether the final radiological condition of the slabs met the release guidelines.

  10. Freezing Spring Temperatures Damage Knobcone Pine

    E-Print Network [OSTI]

    Freezing Spring Temperatures Damage Knobcone Pine Stanley L. Krugman U. S. FOREST SERVICE RESEARCH, Stanley L. 1966. Freezing spring temperatures damage knobcone pine conelets. Berkeley, Calif.. Pacific pine, conelets, freezing temperature) Krugman, Stanley L. 1966. Freezing spring temperatures damage

  11. Data Sharing Report Characterization of Isotope Row Facilities Oak Ridge National Laboratory Oak Ridge TN

    SciTech Connect (OSTI)

    Weaver, Phyllis C

    2013-12-12

    The U.S. Department of Energy (DOE) Oak Ridge Office of Environmental Management (EM-OR) requested that Oak Ridge Associated Universities (ORAU), working under the Oak Ridge Institute for Science and Education (ORISE) contract, provide technical and independent waste management planning support using funds provided by the American Recovery and Reinvestment Act (ARRA). Specifically, DOE EM-OR requested ORAU to plan and implement a survey approach, focused on characterizing the Isotope Row Facilities located at the Oak Ridge National Laboratory (ORNL) for future determination of an appropriate disposition pathway for building debris and systems, should the buildings be demolished. The characterization effort was designed to identify and quantify radiological and chemical contamination associated with building structures and process systems. The Isotope Row Facilities discussed in this report include Bldgs. 3030, 3031, 3032, 3033, 3033A, 3034, 3036, 3093, and 3118, and are located in the northeast quadrant of the main ORNL campus area, between Hillside and Central Avenues. Construction of the isotope production facilities was initiated in the late 1940s, with the exception of Bldgs. 3033A and 3118, which were enclosed in the early 1960s. The Isotope Row facilities were intended for the purpose of light industrial use for the processing, assemblage, and storage of radionuclides used for a variety of applications (ORNL 1952 and ORAU 2013). The Isotope Row Facilities provided laboratory and support services as part of the Isotopes Production and Distribution Program until 1989 when DOE mandated their shutdown (ORNL 1990). These facilities performed diverse research and developmental experiments in support of isotopes production. As a result of the many years of operations, various projects, and final cessation of operations, production was followed by inclusion into the surveillance and maintenance (S&M) project for eventual decontamination and decommissioning (D&D). The process for D&D and final dismantlement of facilities requires that the known contaminants of concern (COCs) be evaluated and quantified and to identify and quantify any additional contaminants in order to satisfy the waste acceptance criteria requirements for the desired disposal pathway. Known facility contaminants include, but are not limited to, asbestos-containing material (ACM), radiological contaminants, and chemical contaminants including polychlorinated biphenyls (PCBs) and metals.

  12. Brush Control and Range Improvement: In the Post Oak-Blackjack Oak Area of Texas. 

    E-Print Network [OSTI]

    Darrow, Robert A.; McCully, Wayne G.

    1959-01-01

    plant treatments with herbi. cides include basal trunk spray, stump spray, frill spray, trunk injection and soil injection. Oil solutions of 2,4,5-T ester are effective for all individual plant treatments. Water suspen- sions of monuron or fenuron... plant or broadcast treat- merits for control sf .woody plants. Rasnl Trunk Spray Rasal spray applications of oil solutions contain- ing 2,4,5-T ester or water suspensions of monuron polvtler are recommended for co~itrol of post and blackjack oaks...

  13. Japanese and American competition in the development of scroll compressors and its impact on the American air conditioning industry

    SciTech Connect (OSTI)

    Ushimaru, Kenji )

    1990-02-01

    This report examines the technological development of scroll compressors and its impact on the air conditioning equipment industry. Scroll compressors, although considered to be the compressors of the future for energy-efficient residential heat pumps and possibly for many other applications, are difficult to manufacture on a volume-production base. The manufacturing process requires computer-aided, numerically controlled tools for high-precision fabrication of major parts. Japan implemented a global strategy for dominating the technological world market in the 1970s, and scroll compressor technology benefited from the advent of new-generation machine tools. As a result, if American manufacturers of scroll compressors purchase or are essentially forced to purchase numerically controlled tools from Japan in the future, they will then become dependent on their own competitors because the same Japanese conglomerates that make numerically controlled tools also make scroll compressors. This study illustrates the importance of the basic machine tool industry to the health of the US economy. Without a strong machine tool industry, it is difficult for American manufacturers to put innovations, whether patented or not, into production. As we experience transformation in the air conditioning and refrigeration market, it will be critical to establish a consistent national policy to provide healthy competition among producers, to promote innovation within the industry, to enhance assimilation of new technology, and to eliminate practices that are incompatible with these goals. 72 refs., 8 figs., 1 tab.

  14. Analysis of instability inception in high-speed multistage axial-flow compressors

    SciTech Connect (OSTI)

    Hendricks, G.J.; Sabnis, J.S.; Feulner, M.R.

    1997-10-01

    A nonlinear, two-dimensional, compressible dynamic model has been developed to study rotating stall/surge inception and development in high-speed, multistage, axial flow compressors. The flow dynamics are represented by the unsteady Euler equations, solved in each interblade row gap and inlet and exit ducts as two-dimensional domains, and in each blade passage as a one-dimensional domain. The resulting equations are solved on a computational grid. The boundary conditions between domains are represented by ideal turning coupled with empirical loss and deviation correlations. Results are presented comparing model simulations to instability inception data of an eleven stage, high-pressure-ratio compressor operating at both part and full power, and the results analyzed in the context of a linear modal analysis.

  15. Spring 2015 National Transportation Stakeholders Forum Meeting...

    Broader source: Energy.gov (indexed) [DOE]

    Spring 2015 National Transportation Stakeholders Forum Meeting, New Mexico The Spring 2015 meeting of the National Transportation Stakeholders Forum will be held on May 12-14, 2015...

  16. Spring Valley Public Utilities - Residential Energy Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    LED Lighting Program Info Sector Name Utility Administrator Spring Valley Public Utilities Website http:www.SaveEnergyInSpringValley.com State Minnesota Program Type Rebate...

  17. Spring 2015 Virtual Toolkit | Department of Energy

    Energy Savers [EERE]

    Virtual Toolkit Spring 2015 Virtual Toolkit Virtual Toolkit for the Spring 2015 BioenergizeME Infographic Challenge. bioenergizemetoolkit2015.pdf More Documents & Publications...

  18. Oak Ridge Reservation environmental report for 1990

    SciTech Connect (OSTI)

    Wilson, A.R.

    1991-09-01

    The purpose of this report is to provide information to the public about the impact of the US Department of Energy's (DOE's) facilities located on the Oak Ridge Reservation (ORR) on the public and the environment. It describes the environmental surveillance and monitoring activities conducted at and around the DOE facilities operated by Martin Marietta Energy Systems, Inc. Preparation and publication of this report is in accordance with DOE Order 5400.1. The order specifies a publication deadline of June of the following year for each calendar year of data. The primary objective of this report is to summarize all information collected for the previous calendar year regarding effluent monitoring, environmental surveillance, and estimates of radiation and chemical dose to the surrounding population. When multiple years of information are available for a program, trends are also evaluated. The first seven sections of Volume 1 of this report address this objective. The last three sections of Volume 1 provide information on solid waste management, special environmental studies, and quality assurance programs.

  19. SPRING ISD CATEE 2014 

    E-Print Network [OSTI]

    Windsor, J.

    2014-01-01

    stream_source_info ESL-KT-14-11-05.pdf.txt stream_content_type text/plain stream_size 3705 Content-Encoding UTF-8 stream_name ESL-KT-14-11-05.pdf.txt Content-Type text/plain; charset=UTF-8 SPRING ISD CATEE 2014 ESL...-KT-14-11-05 CATEE 2014: Clean Air Through Efficiency Conference, Dallas, Texas Nov. 18-20 Benchmarking results ESL-KT-14-11-05 CATEE 2014: Clean Air Through Efficiency Conference, Dallas, Texas Nov. 18-20 Annual energy cost by facility ESL-KT-14...

  20. VRF on-site Measurement by Compressor Curve Method of VRF and the applications-APCBC 

    E-Print Network [OSTI]

    Kan,Y.; Shiochi,S.

    2014-01-01

    by Compressor Curve Method and Its Application Sumio Shiochi (Daikin Industries,ltd.) Yurino Kan* (Daikin Industries,ltd.) APCBC presentation in ICEBO (Asia Pacific Conference on Building Commissioning) Sept. 2014, Beijing, China ESL-IC-14...-09-34 Proceedings of the 14th International Conference for Enhanced Building Operations, Beijing, China, September 14-17, 2014 ICEBO 2014 Beijing + APCBC Meeting 2014.9.15-16 1. Background and Purpose of This Study ?Background? Stereotype of VRF from Architectural...

  1. Modeling for control of rotating stall in high-speed multistage axial compressors

    SciTech Connect (OSTI)

    Feulner, M.R.; Hendricks, G.J.; Paduano, J.D.

    1996-01-01

    Using a two-dimensional compressible flow representation of axial compressor dynamics, a control-theoretic input-output model is derived, which is of general utility in rotating stall/surge active control studies. The derivation presented here begins with a review of the fluid dynamic model, which is a two-dimensional stage stacking technique that accounts for blade row pressure rise, loss, and deviation as well as blade row and interblade row compressible flow. This model is extended to include the effects of the upstream and downstream geometry and boundary conditions, and then manipulated into a transfer function form that dynamically relates actuator motion to sensor measurements. Key relationships in this input-output form are then approximated using rational polynomials. Further manipulation yields an approximate model in standard form for studying active control of rotating stall and surge. As an example of high current relevance, the transfer function from an array of jet actuators to an array of static pressure sensors is derived. Numerical examples are also presented, including a demonstration of the importance of proper choice of sensor and actuator locations, as well as a comparison between sensor types. Under a variety of conditions, it was found that sensor locations near the front of the compressor or in the downstream gap are consistently the best choices, based on a quadratic optimization criterion and a specific three-stage compressor model. The modeling and evaluation procedures presented here are a first step toward a rigorous approach to the design of active control systems for high-speed axial compressors.

  2. Compressor Calorimeter Test of R-410A Alternatives R-32, DR-5, and L-41a

    SciTech Connect (OSTI)

    Shrestha, Som S [ORNL; Mahderekal, Isaac [ORNL; Sharma, Vishaldeep [ORNL; Abdelaziz, Omar [ORNL

    2013-02-01

    As a contribution to the AHRI Low-GWP Alternative Refrigerants Evaluation Program (AREP), this study compares performance of alternative refrigerants R32, DR-5, and L-41A to that of refrigerant R-410A (baseline) in a scroll compressor designed for air-conditioning and heat pump applications. Compressor calorimeter tests were performed to evaluate the performance of the lower-GWP alternative refrigerants in place of the common refrigerant R-410A in a 36,000 Btu/hr compressor calorimeter using a compressor having a nominal rated capacity of 21,300 Btu/hr. Tests were conducted over a suction dew point temperature range of 10 F to 55 F in 5 F increments and a discharge dew point temperature range of 70 F to 140 F in 10 F increments. All the tests were performed with 20 F superheat, 40 F superheat and 65 F suction temperature. A liquid subcooling level of 15 F was maintained for all the test conditions. The tests showed that performance of these three lower-GWP alternative refrigerants is comparable to that of R-410A. For the 20 F superheat and 15 F subcooling test conditions, EERs of R32, DR-5, and L-41A were 90% to 99%, 96% to 99%, and 94% to 101%, respectively, compared to that of R-410A. Similarly, cooling capacities of R32, DR-5, and L-41A were 98% to 103%, 92% to 96%, and 84% to 92%, respectively, compared to that of R-410A.

  3. A modified post damping ring bunch compressor beamline for the TESLA linear collider

    SciTech Connect (OSTI)

    Philippe R.-G. Piot; Winfried Decking

    2004-03-23

    We propose a modified bunch compressor beamline, downstream of the damping ring, for the TESLA linear collider. This modified beamline uses a third harmonic radio-frequency section based on the 3.9 GHz superconducting cavity under development at Fermilab. In our design the beam deceleration is about {approx}50 MeV instead of {approx}450 MeV in the original design proposed.

  4. Practical exergy analysis of centrifugal compressor performance using ASME-PTC-10 data

    SciTech Connect (OSTI)

    Carranti, F.J. [Hoffman Air and Filtration Systems, Syracuse, NY (United States)

    1997-07-01

    It has been shown that measures of performance currently in use for industrial and process compressors do not give a true measure of energy utilization, and that the required assumptions of isentropic or adiabatic behavior are now always valid. A better indication of machine or process performance can be achieved using exergetic (second law) efficiencies and by employing the second law of thermodynamics to indicate the nature of irreversibilities and entropy generation in the compression process. In this type of analysis, performance is related to an environmental equilibrium condition, or dead state. Often, the differences between avoidable and unavoidable irreversibilities ca be interpreted from these results. A general overview of the techniques involved in exergy analysis as applied to compressors and blowers is presented. A practical method to allow the calculation of exergetic efficiencies by manufacturers and end users is demonstrated using data from ASME Power Test Code input. These data are often readily available from compressor manufacturers for both design and off-design conditions, or can sometimes be obtained from field measurements. The calculations involved are simple and straightforward, and can demonstrate the energy usage situation for a variety of conditions. Here off-design is taken to mean at different rates of flow, as well as at different environmental states. The techniques presented are also applicable to many other equipment and process types.

  5. Bifurcation analysis of surge and rotating stall in axial flow compressors

    SciTech Connect (OSTI)

    Abed, E.H. ); Houpt, P.K. . Corporate Research and Development Center); Hosny, W.M. . Engine Operability Div.)

    1993-10-01

    The surge and rotating stall post-instability behaviors of axial flow compressors are investigated from a bifurcation-theoretic perspective, using a model and system data presented by Greitzer (1976a). For this model, a sequence of local and global bifurcations of the nonlinear system dynamics is uncovered. This includes a global bifurcation of a pair of large-amplitude periodic solutions. Resulting from this bifurcation are a stable oscillation (surge) and an unstable oscillation (antisurge). The latter oscillation is found to have a deciding significance regarding the particular post-instability behavior experienced by the compressor. These results are used to reconstruct Greitzer's (1976b) findings regarding the manner in which post-instability behavior depends on system parameters. Although the model does not directly reflect non axisymmetric dynamics, use of a steady-state compressor characteristic approximating the measured characteristic of Greitzer (1976a) is found to result in conclusions that compare well with observation. Thus, the paper gives a convenient and simple explanation of the boundary between surge and rotating stall behaviors, without the use of more intricate models and analyses including non axisymmetric flow dynamics.

  6. Rotating stall control of an axial flow compressor using pulsed air injection

    SciTech Connect (OSTI)

    D`Andrea, R.; Behnken, R.L.

    1997-10-01

    This paper presents the use of pulsed air injection to control rotating stall in a low-speed, axial flow compressor. In the first part of the paper, the injection of air is modeled as an unsteady shift of the compressor characteristic, and incorporated into a low dimensional model of the compressor. By observing the change in the bifurcation behavior of this model subject to nonlinear feedback, the viability of various air injection orientations is established. An orientation consistent with this analysis is then used for feedback control. By measuring the unsteady pressures near the rotor face, a control algorithm determines the magnitude and phase of the first mode of rotating stall and controls the injection of air in the front of the rotor face. Experimental results show that this technique eliminates the hysteresis loop normally associated with rotating stall. A parametric study is used to determine the optimal control parameters for suppression of stall. The resulting control strategy is also shown to suppress surge when a plenum is present. Using a high-fidelity model, the main features of the experimental results are duplicated via simulations.

  7. Characterization plan for the Oak Ridge National Laboratory Area-Wide Groundwater Program, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1994-08-01

    This characterization plan has been developed as part of the U.S. Department of Energy`s (DOE`s) investigation of the Groundwater Operable Unit (GWOU) at Oak Ridge National Laboratory (ORNL) located near Oak Ridge, Tennessee. The first iteration of the characterization plan is intended to serve as a strategy document to guide subsequent GWOU remedial investigations. The plan provides a rationale and organization for groundwater data acquisition, monitoring, and remedial actions to be performed during implementation of environmental restoration activities associated with the ORNL GWOU. It is important to note that the characterization plan for the ORNL GWOU is not a prototypical work plan. As such, remedial investigations will be conducted using annual work plans to manage the work activities, and task reports will be used to document the results of the investigations. Sampling and analysis results will be compiled and reported annually with a review of data relative to risk (screening level risk assessment review) for groundwater. This characterization plan outlines the overall strategy for the remedial investigations and defines tasks that are to be conducted during the initial phase of investigation. This plan is presented with the understanding that more specific addenda to the plan will follow.

  8. Quality assurance plan for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1994-01-01

    This Quality Assurance Plan (QAP) is concerned with design and construction (Sect. 2) and characterization and monitoring (Sect. 3). The basis for Sect. 2 is the Quality Assurance Plan for the Design and Construction of Waste Area Grouping 6 Closure at Oak Ridge National Laboratory, Oak Ridge, Tennessee, and the basis for Sect. 3 is the Environmental Restoration Quality Program Plan. Combining the two areas into one plan gives a single, overall document that explains the requirements and from which the individual QAPs and quality assurance project plans can be written. The Waste Area Grouping (WAG) 6 QAP establishes the procedures and requirements to be implemented for control of quality-related activities for the WAG 6 project. Quality Assurance (QA) activities are subject to requirements detailed in the Martin Marietta Energy Systems, Inc. (Energy Systems), QA Program and the Environmental Restoration (ER) QA Program, as well as to other quality requirements. These activities may be performed by Energy Systems organizations, subcontractors to Energy Systems, and architect-engineer (A-E) under prime contract to the US Department of Energy (DOE), or a construction manager under prime contract to DOE. This plan specifies the overall Energy Systems quality requirements for the project. The WAG 6 QAP will be supplemented by subproject QAPs that will identify additional requirements pertaining to each subproject.

  9. White Oak Creek Watershed: Melton Valley Area Remedial Investigation Report, Oak Ridge National Laboratory, Oak Ridge, Tennessee: Volume 3 Appendix C

    SciTech Connect (OSTI)

    1996-11-01

    This report provides details on the baseline ecological risk assessment conducted in support of the Remedial Investigation (RI) Report for the Melton Valley areas of the White Oak Creek watershed (WOCW). The RI presents an analysis meant to enable the US Department of Energy (DOE) to pursue a series of remedial actions resulting in site cleanup and stabilization. The ecological risk assessment builds off of the WOCW screening ecological risk assessment. All information available for contaminated sites under the jurisdiction of the US Department of Energy`s Comprehensive Environmental Response, Compensation, and Liability Act Federal Facilities Agreement within the White Oak Creek (WOC) RI area has been used to identify areas of potential concern with respect to the presence of contamination posing a potential risk to ecological receptors within the Melton Valley area of the White Oak Creek watershed. The risk assessment report evaluates the potential risks to receptors within each subbasin of the watershed as well as at a watershed-wide scale. The WOC system has been exposed to contaminant releases from Oak Ridge National Laboratory and associated operations since 1943 and continues to receive contaminants from adjacent waste area groupings.

  10. Effect of Warming and Precipitation Distribution on Soil Respiration and Mycorrhizal Abundance in Post Oak Savannah 

    E-Print Network [OSTI]

    Cartmill, Andrew David

    2012-07-16

    , and precipitation distribution on soil CO2 efflux, its underlying components, and mycorrhizal abundance in southern post oak savannah. Post oak savannah in the south-central US are dominated by three contrasting plant functional types: Schizachyrium scoparium (Michx...

  11. SpringFall Summ SpringFall Summ SpringFall Summ SpringFall Summ Year #1 Year #2 Year #3 Year #4

    E-Print Network [OSTI]

    Suzuki, Masatsugu

    . (if needed) Events During Defense-Semester ECE PhD Time-LinePost-MS 3rd Week Week N - 7 Week N - 1SpringFall Summ SpringFall Summ SpringFall Summ SpringFall Summ Year #1 Year #2 Year #3 Year #4

  12. The Oak Ridge Reservation Annual Site Environmental Report, 2007

    SciTech Connect (OSTI)

    Hughes, Joan; Thompson, Sharon; Page, David

    2008-09-30

    The Oak Ridge Reservation (ORR) consists of three major government-owned, contractor-operated facilities: the Y-12 National Security Complex, Oak Ridge National Laboratory, and East Tennessee Technology Park. The ORR was established in the early 1940s as part of the Manhattan Project, a secret undertaking that produced materials for the first atomic bombs. The reservation’s role has evolved over the years, and it continues to adapt to meet the changing defense, energy, and research needs of the United States. Both the work carried out for the war effort and subsequent research, development, and production activities have involved, and continue to involve, the use of radiological and hazardous materials. The Oak Ridge Reservation Annual Site Environmental Report and supporting data are available at Http://www.ornl.gov/sci/env_rpt or from the project director.

  13. Level 3 Baseline Risk Assessment for Building 3515 at Oak Ridge National Lab., Oak Ridge, TN

    SciTech Connect (OSTI)

    Wollert, D.A.; Cretella, F.M.; Golden, K.M.

    1995-08-01

    The baseline risk assessment for the Fission Product Pilot Plant (Building 3515) at the Oak Ridge National laboratory (ORNL) provides the Decontamination and Decommissioning (D&D) Program at ORNL and Building 3515 project managers with information concerning the results of the Level 3 baseline risk assessment performed for this building. The document was prepared under Work Breakdown Structure 1.4.12.6.2.01 (Activity Data Sheet 3701, Facilities D&D) and includes information on the potential long-term impacts to human health and the environment if no action is taken to remediate Building 3515. Information provided in this document forms the basis for the development of remedial alternatives and the no-action risk portion of the Engineering Evaluation/Cost Analysis report.

  14. Final Independent External Peer Review Report for the White Oak Bayou Federal Flood Damage

    E-Print Network [OSTI]

    US Army Corps of Engineers

    Final Independent External Peer Review Report for the White Oak Bayou Federal Flood Damage Independent External Peer Review Report for the White Oak Bayou Federal Flood Damage Reduction Plan PEER REVIEW REPORT for the White Oak Bayou Federal Flood Damage Reduction Plan EXECUTIVE SUMMARY White

  15. NEWS RELEASE GOLDSPOTTED OAK BORER INTERAGENCY WORKING GROUP OF SAN DIEGO

    E-Print Network [OSTI]

    Ishida, Yuko

    NEWS RELEASE GOLDSPOTTED OAK BORER INTERAGENCY WORKING GROUP OF SAN DIEGO COUNTY CONTACT: Anabele Cornejo, Forest Service, 858-674-2985 Tammy Glenn, County of San Diego, 619-595-4627 Nick Schuler, CAL FIRE, 619-590-3100 DON'T MOVE OAK WOOD IN SAN DIEGO COUNTY! Dead, Dying, and Diseased Oaks

  16. Blue Oak Canopy Effect On Seasonal Forage Production and Quality1

    E-Print Network [OSTI]

    Blue Oak Canopy Effect On Seasonal Forage Production and Quality1 William E. Frost Neil K. Mc the canopy of blue oak (Quercus douglasii) and in open grassland at the San Joaquin Experimental Range blue oak compared to open grassland. At most sampling dates, the protein content was greater

  17. Oak Ridge National Laboratory Evaluation for Drum Characterization and

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergyTher i nAand DOEDepartmentNew2008Group,OAK RIDGE, Tenn.Use |Oak Ridge NationalSource

  18. Oak Ridge Office of Environmental Management P.O

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirley Ann Jackson About1996How to ApplytheExecutive71.1 OMB ControlOak of EnvironmentalY-12OakO .

  19. Survey of protected vascular plants on the Oak Ridge Reservation, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Awl, D.J.; Pounds, L.R.; Rosensteel, B.A.; King, A.L.; Hamlett, P.A.

    1996-06-01

    Vascular plant surveys were initiated during fiscal year 1992 by the environmentally sensitive areas program to determine the baseline condition of threatened and endangered (T&E) vascular plant species on the Oak Ridge Reservation (ORR). T&E species receive protection under federal and state regulations. In addition, the National Environmental Policy Act (NEPA) requires that federally-funded projects avoid or mitigate impacts to listed species. T&E plant species found on or near the U.S. Department of Energy`s (DOE) Oak Ridge Reservation (ORR) are identified. Twenty-eight species identified on the ORR are listed by the Tennessee Department of Environment and Conservation as either endangered, threatened, or of special concern. Four of these have been under review by the U.S. Fish and Wildlife Service for possible listing (listed in the formerly-used C2 candidate category). Additional species listed by the state occur near and may be present on the ORR. A range of habitats support the rare taxa on the ORR: river bluffs, sinkholes, calcareous barrens, wetlands, utility corridors, and forests. The list of T&E plant species and their locations on the ORR should be considered provisional because the entire ORR has not been surveyed, and state and federal status of all species continues to be updated. The purpose of this document is to present information on the listed T&E plant species currently known to occur on the ORR as well as listed species potentially occurring on the ORR based on geographic range and habitat availability. For the purpose of this report, {open_quotes}T&E species{close_quotes} include all federal- and state-listed species, including candidates for listing, and species of special concern. Consideration of T&E plant habitats is an important component of resource management and land-use planning; protection of rare species in their natural habitat is the best method of ensuring their long-term survival.

  20. MA 154 Schedule, Spring 2004

    E-Print Network [OSTI]

    math

    2015-01-05

    MA 13800 Calendar Spring 2015. Exam 1: Monday, February 9, 2015 at 8:00 in MATH 175. Exam 2: Monday, March 9, 2015 at 6:30 in MATH 175. Exam 3: ...

  1. MA 154 Schedule, Spring 2004

    E-Print Network [OSTI]

    math

    2013-03-20

    MA 15400 Online Lessons Links. Spring 2013. PP = PowerPoint. Boiler Cast Link = A recording of that days class. (this link will take you to all of the recordings).

  2. Genetic variation in post-epidemic and pre-epidemic live oak populations subject to oak wilt 

    E-Print Network [OSTI]

    Bellamy, Brenda Kay

    1992-01-01

    GENETIC VARIATION IN POST-EPIDEMIC AND PRE-EPIDEMIC LIVE OAK POPULATIONS SUBJECT TO OAR WILT A Thesis by BRENDA KAY BELLAMY Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE May 1992 Major Subject: Plant Pathology GENETIC VARIATION XN POST-EPIDEMIC AND PRE-EPXDENIC LIVE OAK POPULATXONS SUBJECT TO OAE WILT A Thesis by BRENDA KAY BELLAMY Approved as to style and content by: David N. Ap...

  3. Bear Creek Valley Floodplain Hot Spot Removal Action Project Plan, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    NONE

    1998-01-01

    The Bear Creek Valley Floodplain Hot Spot Removal Action Project Plan, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee (Y/ER-301) was prepared (1) to safely, cost-effectively, and efficiently evaluate the environmental impact of solid material in the two debris areas in the context of industrial land uses (as defined in the Bear Creek Valley Feasibility Study) to support the Engineering Evaluation/Cost Assessment and (2) to evaluate, define, and implement the actions to mitigate these impacts. This work was performed under Work Breakdown Structure 1.x.01.20.01.08.

  4. Hydrologic data summary for the White Oak Creek watershed at Oak Ridge National Laboratory, Oak Ridge, Tennessee, January--December 1994

    SciTech Connect (OSTI)

    Borders, D.M.; Ziegler, K.S.; Reece, D.K.; Watts, J.A.; Frederick, B.J.; McCalla, W.L.; Pridmore, D.J.

    1995-08-01

    This report summarizes, for the 12-month period January through December 1994, the available dynamic hydrologic data collected on the White Oak Creek (WOC) watershed as well as information collected on surface flow systems in the surrounding vicinity that may affect the quality or quantity of surface water in the watershed. The collection of hydrologic data is one component of numerous, ongoing Oak Ridge National Laboratory (ORNL) environmental studies and monitoring programs and is intended to characterize the quantity and quality of water in the surface flow system, assist with the planning and assessment of remedial action activities, provide long-term availability of data and quality assurance of these data, and support long-term measures of contaminant fluxes at a spatial scale to provide a comprehensive picture of watershed performance that is commensurate with future remedial actions.

  5. Internally-cooled centrifugal compressor with cooling jacket formed in the diaphragm

    DOE Patents [OSTI]

    Moore, James J.; Lerche, Andrew H.; Moreland, Brian S.

    2014-08-26

    An internally-cooled centrifugal compressor having a shaped casing and a diaphragm disposed within the shaped casing having a gas side and a coolant side so that heat from a gas flowing though the gas side is extracted via the coolant side. An impeller disposed within the diaphragm has a stage inlet on one side and a stage outlet for delivering a pressurized gas to a downstream connection. The coolant side of the diaphragm includes at least one passageway for directing a coolant in a substantially counter-flow direction from the flow of gas through the gas side.

  6. Natural Gas Compressor Stations on the Interstate Pipeline Network: Developments Since 1996

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustments (Billion Cubic Feet) Wyoming963Residential2, 2014ProvedYear Jan FebYear Jan Feb Mar Apr MayCompressor

  7. Technology Solutions Case Study: Foundation Heat Exchanger, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    2014-03-01

    The foundation heat exchanger, developed by Oak Ridge National Laboratory, is a new concept for a cost-effective horizontal ground heat exchanger that can be connected to water-to-water or water-to-air heat pump systems for space conditioning as well as domestic water heating.

  8. Oak Ridge Reservation. Physical Characteristics and National Resources

    SciTech Connect (OSTI)

    Parr, Patricia Dreyer; Joan, F. Hughes

    2006-10-09

    The topology, geology, hydrology, vegetation, and wildlife of the Oak Ridge Reservation (ORR) provide a complex and intricate array of resources that directly impact land stewardship and use decisions. The purpose of this document is to consolidate general information regarding the natural resources and physical characteristics of the ORR.

  9. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    U. S. DEPARTMENT OF ENERGY The boon vs. bust polarity applies especially to trees and forests Boon1 OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY AAAS Symposium CO2 Fertilization: Boon or Bust? Dynamic Responses of Forest Trees to CO2 Fertilization: Will the Stimulation Persist? Richard J

  10. CRAD, Management- Oak Ridge National Laboratory High Flux Isotope Reactor

    Broader source: Energy.gov [DOE]

    A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a February 2007 assessment of the Management in preparation for restart of the Oak Ridge National Laboratory High Flux Isotope Reactor.

  11. CRAD, Management- Oak Ridge National Laboratory TRU ALPHA LLWT Project

    Broader source: Energy.gov [DOE]

    A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a November 2003 assessment of the Management Program portion of an Operational Readiness Review of the Oak Ridge National Laboratory TRU ALPHA LLWT Project.

  12. CRAD, Training- Oak Ridge National Laboratory TRU ALPHA LLWT Project

    Broader source: Energy.gov [DOE]

    A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a November 2003 assessment of the Training Program portion of an Operational Readiness Review of the Oak Ridge National Laboratory TRU ALPHA LLWT Project.

  13. Osmotic adjustment in sessile oak seedlings in response to drought

    E-Print Network [OSTI]

    Boyer, Edmond

    Note Osmotic adjustment in sessile oak seedlings in response to drought C Collet JM Guehl 1 Équipe of drought development, respectively, and leaf osmotic potential at full tur- gor reached values of -2.0 and -1.5 MPa, for the same treatments. For both treatments, leaf water poten- tial and leaf osmotic

  14. CRAD, Engineering- Oak Ridge National Laboratory High Flux Isotope Reactor

    Broader source: Energy.gov [DOE]

    A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a February 2007 assessment of the Engineering Program in preparation for restart of the Oak Ridge National Laboratory High Flux Isotope Reactor.

  15. CRAD, Training- Oak Ridge National Laboratory High Flux Isotope Reactor

    Broader source: Energy.gov [DOE]

    A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a February 2007 assessment of the Training Program in preparation for restart of the Oak Ridge National Laboratory High Flux Isotope Reactor.

  16. Utilization Implications for Hardwoods Susceptible to Sudden Oak Death1

    E-Print Network [OSTI]

    Utilization Implications for Hardwoods Susceptible to Sudden Oak Death1 John R. Shelly2 The number (Lithocarpus densiflorus) utilization, one of the SOD susceptible species, provide valuable insight into the potential for utilizing SOD infected material. Tanoak was found to have very good woodworking properties

  17. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY Diversity of Microbial Genes Involved affect microbial communities either directly or indirectly through changes in temperature or plant communities. Soil microbial communities that drive processes such as those involved in nitrogen and methane

  18. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    Pennycook, Steve

    -Supercritical Steam Service - Turbines Phil Maziasz Materials Science and Technology Division Oak Ridge National LABORATORY U. S. DEPARTMENT OF ENERGY 4 DOE/EIO/EPRI ­ A-USC Steam Turbine Materials Consortium · Project · Steam Turbine Consortium Project (Phase I) included General Electric, Alstom and Siemens; Phase II

  19. Oak Ridge National Laboratory Institutional Plan, FY 1995--FY 2000

    SciTech Connect (OSTI)

    Not Available

    1994-11-01

    This report discusses the institutional plan for Oak Ridge National Laboratory for the next five years (1995-2000). Included in this report are the: laboratory director`s statement; laboratory mission, vision, and core competencies; laboratory plan; major laboratory initiatives; scientific and technical programs; critical success factors; summaries of other plans; and resource projections.

  20. SNS Experimental Facilities Oak Ridge1 SNS Project Overview

    E-Print Network [OSTI]

    McDonald, Kirk

    Site #12;SNS Experimental Facilities Oak Ridge5 The Accelerator Configuration will include a SuperConducting RF System The Accelerator Configuration has been established and the high-energy end of the Linac spots of Hg caused by recirculation around flow baffles · Demonstration of key systems: ­ Mercury loop

  1. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    Deiterding, Ralf

    -Battelle, LLC under Contract No. DE-AC05-00OR22725. Part of this work was also performed at the California No. B341492 of DOE contract W-7405-ENG-48. #12;3 OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT-order unstructured scheme · Appropriate level-set-based refinement criteria are available to cure deficiencies #12

  2. Oak Ridge Reservation Annual Site environmental report for 1994

    SciTech Connect (OSTI)

    Koncinski, W.S.

    1995-10-01

    This report presents the details of the environmental monitoring and management plan for the Oak Ridge Reservation. Topics include: site and operations overview; environmental compliance strategies; environmental management program; effluent monitoring; environmental surveillance; radiation doses; chemical doses; ground water; and quality assurance.

  3. Oak Ridge Reservation, annual site environmental report for 1993

    SciTech Connect (OSTI)

    Not Available

    1994-11-01

    The US DOE currently oversees activities on the Oak Ridge Reservation, a government-owned, contractor-operated facility. Three sites compose the reservation; Y-12, Oak Ridge National Laboratory, and K-25. This document contains a summary of environmental monitoring activities on the Oak Ridge Reservation (ORR) and its surroundings. The results summarized in this report are based on the data collected during calendar year (CY) 1993 and compiled in; Environmental Monitoring in the Oak Ridge Reservation: CY 1993 Results. Annual environmental monitoring on the ORR consists of two major activities: effluent monitoring and environmental surveillance. Effluent monitoring is the collection and analysis of samples or measurements of liquid, gaseous, or airborne effluents for the purpose of characterizing and quantifying contaminants and process stream characteristics, assessing radiation and chemical exposures to members of the public, and demonstrating compliance with applicable standards. Environmental surveillance is the collection and analysis of samples of air, water, soil, foodstuffs, biota, and other media from DOE sites and their environs and the measurement of external radiation for purposes of demonstrating compliance with applicable standards, assessing radiation and chemical exposures to members of the public, and assessing effects, if any, on the local environment.

  4. CRAD, Maintenance- Oak Ridge National Laboratory High Flux Isotope Reactor

    Broader source: Energy.gov [DOE]

    A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a February 2007 assessment of the Maintenance Program in preparation for restart of the Oak Ridge National Laboratory High Flux Isotope Reactor.

  5. Environmental Compliance and Protection Program Description Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Bechtel Jacobs

    2009-02-26

    The objective of the Environmental Compliance and Protection (EC and P) Program Description (PD) is to establish minimum environmental compliance requirements and natural resources protection goals for the Bechtel Jacobs Company LLC (BJC) Oak Ridge Environmental Management Cleanup Contract (EMCC) Contract Number DE-AC05-98OR22700-M198. This PD establishes the work practices necessary to ensure protection of the environment during the performance of EMCC work activities on the US Department of Energy's (DOE's) Oak Ridge Reservation (ORR) in Oak Ridge, Tennessee, by BJC employees and subcontractor personnel. Both BJC and subcontractor personnel are required to implement this PD. A majority of the decontamination and demolition (D and D) activities and media (e.g., soil and groundwater) remediation response actions at DOE sites on the ORR are conducted under the authority of the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). CERCLA activities are governed by individual CERCLA decision documents (e.g., Record of Decision [ROD] or Action Memorandum) and according to requirements stated in the Federal Facility Agreement for the Oak Ridge Reservation (DOE 1992). Applicable or relevant and appropriate requirements (ARARs) for the selected remedy are the requirements for environmental remediation responses (e.g., removal actions and remedial actions) conducted under CERCLA.

  6. Climate Change Science Institute at Oak Ridge National Laboratory

    E-Print Network [OSTI]

    Climate Change Science Institute at Oak Ridge National Laboratory A multidisciplinary research the consequences of climate change, and evaluate and inform policy responses to climate change Highlights of CCSI research include · Participation in the Intergovernmental Panel on Climate Change Fifth Assessment Report

  7. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY

    E-Print Network [OSTI]

    1/11/2007 OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY Apr 1999Aug 1999Dec 1999Apr 2000 estimates of carbon dioxide emissions from fossil-fuel consumption in Brazil during the late 1990s and early to other countries where the underlying energy statistical data base is not as robust as that in the U

  8. Oak Ridge Y-12 Plant groundwater protection program management plan

    SciTech Connect (OSTI)

    NONE

    1996-06-01

    The Oak Ridge Y- 1 2 Plant (Y-12 Plant) is owned by the United States Department of Energy (DOE) and managed by Lockheed Martin Energy Systems, Inc. (Energy Systems) under contract No. DE-AC05-84OR21400. The Y-12 Plant Groundwater Protection Program (GWPP), which was initiated in 1975, provides for the protection of groundwater resources consistent with Federal, State, and local regulations, and in accordance with DOE orders and Energy Systems policies and procedures. The Y-12 Plant is located in Anderson County, Tennessee, and is within the corporate limits of the City of Oak Ridge. The Y-12 Plant is one of three major DOE complexes that comprise the 37,000-acre Oak Ridge Reservation (ORR) located in Anderson and Roane counties. The Y-12 Plant is located in Bear Creek Valley at an elevation of about 950 feet (ft) above sea level. Bear Creek Valley is bounded on the northwest and southeast, and is isolated from populated areas of Oak Ridge, by parallel ridges that rise about 300 ft above the valley floor. The Y-12 Plant and its fenced buffer area are about 0.6 mile wide by 3.2 miles long and cover approximately 4,900 acres. The main industrialized section encompasses approximately 800 acres.

  9. Original article Is site preparation necessary for bur oak receiving

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    (glyphosate herbicide or black plastic mulching) in 120 cm strips over the seedling rows of bur oak (Quercus were larger in the plastic mulch treatment than in the glyphosate treatment. Results support plastic mulch / Quercus macrocarpa Résumé - La préparation du site est-elle nécessaire lorsqu

  10. 1Oak Ridge National Laboratory Science & Technology Highlights

    E-Print Network [OSTI]

    Pennycook, Steve

    - bility data · Joining technologies for composites and dissimilar materials · Cost-effective recycling1Oak Ridge National Laboratory Science & Technology Highlights Published by ORNL's Energy less than and costs about the same as a steel body. Focal Project 3 (FP3), a part of DOE's Freedom

  11. DOE/ORO/2218 Oak Ridge Reservation Annual Site

    E-Print Network [OSTI]

    Pennycook, Steve

    Laboratory East Tennessee Technology Park Electronic publisher Coordinating editor Graphic artists Brenda of Energy under Contract No. DE-AC05-00OR22800 and by East Tennessee Technology Park P.O. Box 4699, Oak ................................................................................................... 1-1 1.3 Climate

  12. ACEEE Summer Study on Energy in Industry, West Point, NY, July 19-22. 1 Modeling and Simulation of Air Compressor Energy Use

    E-Print Network [OSTI]

    Kissock, Kelly

    of Air Compressor Energy Use Chris Schmidt, Energy & Resource Solutions, Inc. Kelly Kissock, Department compressor energy use to estimate energy savings in compressed air systems from air use reduction and other of this method to estimate energy savings from changing control modes and reducing air use is described

  13. 65USDA Forest Service Gen. Tech. Rep. PSW-GTR-160. 1997. Soil Characteristics of Blue Oak and

    E-Print Network [OSTI]

    65USDA Forest Service Gen. Tech. Rep. PSW-GTR-160. 1997. Soil Characteristics of Blue Oak and Coast, California, soils associated with blue oaks (Quercus douglasii) are slightly more acidic, have finer textures are richer in organic matter than those associated with blue oaks. Blue oaks seem to grow more frequently

  14. Soil Management Plan for the Oak Ridge Y-12 National Security Complex Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    2005-03-02

    This Soil Management Plan applies to all activities conducted under the auspices of the National Nuclear Security Administration (NNSA) Oak Ridge Y-12 National Security Complex (Y-12) that involve soil disturbance and potential management of waste soil. The plan was prepared under the direction of the Y-12 Environmental Compliance Department of the Environment, Safety, and Health Division. Soil disturbances related to maintenance activities, utility and building construction projects, or demolition projects fall within the purview of the plan. This Soil Management Plan represents an integrated, visually oriented, planning and information resource tool for decision making involving excavation or disturbance of soil at Y-12. This Soil Management Plan addresses three primary elements. (1) Regulatory and programmatic requirements for management of soil based on the location of a soil disturbance project and/or the regulatory classification of any contaminants that may be present (Chap. 2). Five general regulatory or programmatic classifications of soil are recognized to be potentially present at Y-12; soil may fall under one or more these classifications: (a) Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) pursuant to the Oak Ridge Reservation (ORR) Federal Facilities Agreement; (b) Resource Conservation and Recovery Act (RCRA); (c) RCRA 3004(u) solid waste managements units pursuant to the RCRA Hazardous and Solid Waste Amendments Act of 1984 permit for the ORR; (d) Toxic Substances and Control Act-regulated soil containing polychlorinated biphenyls; and (e) Radiologically contaminated soil regulated under the Atomic Energy Act review process. (2) Information for project planners on current and future planned remedial actions (RAs), as prescribed by CERCLA decision documents (including the scope of the actions and remedial goals), land use controls implemented to support or maintain RAs, RCRA post-closure regulatory requirements for former waste management units, legacy contamination source areas and distribution of contamination in soils, and environmental infrastructure (e.g., caps, monitoring systems, etc.) that is in place or planned in association with RAs. (3) Regulatory considerations and processes for management and disposition of waste soil upon generation, including regulatory drivers, best management practices (BMPs), waste determination protocols, waste acceptance criteria, and existing waste management procedures and BMPs for Y-12. This Soil Management Plan provides information to project planners to better coordinate their activities with other organizations and programs with a vested interest in soil disturbance activities at Y-12. The information allows project managers and maintenance personnel to evaluate and anticipate potential contaminant levels that may be present at a proposed soil disturbance site prior to commencement of activities and allows a more accurate assessment of potential waste management requirements.

  15. Site characterization plan for groundwater in Waste Area Grouping 1 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Lee, R.R.; Curtis, A.H.; Houlberg, L.M.; Purucker, S.T.; Singer, M.L.; Tardiff, M.F.; Wolf, D.A.

    1994-07-01

    The Waste Area Grouping (WAG) 1 Groundwater Operable Unit (OU) at Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee, is undergoing a site characterization to identify environmental contamination that may be present. This document, Site Characterization Report for Groundwater in Waste Area Grouping I at Oak Ridge National Laboratory, Oak Ridge, Tennessee, identifies areas of concern with respect to WAG 1 groundwater and presents the rationale, justification, and objectives for conducting this continuing site characterization. This report summarizes the operations that have taken place at each of the areas of concern in WAG 1, summarizes previous characterization studies that have been performed, presents interpretations of previously collected data and information, identifies contaminants of concern, and presents an action plan for further site investigations and early actions that will lead to identification of contaminant sources, their major groundwater pathways, and reduced off-site migration of contaminated groundwater to surface water. Site characterization Activities performed to date at WAG I have indicated that groundwater contamination, principally radiological contamination, is widespread. An extensive network of underground pipelines and utilities have contributed to the dispersal of contaminants to an unknown extent. The general absence of radiological contamination in surface water at the perimeter of WAG 1 is attributed to the presence of pipelines and underground waste storage tank sumps and dry wells distributed throughout WAG 1 which remove more than about 40 million gal of contaminated groundwater per year.

  16. Oak Ridge National Laboratory Biological Monitoring and Abatement Program for White Oak Creek Watershed and the Clinch River

    SciTech Connect (OSTI)

    Loar, J.M.; Adams, S.M.; Allison, L.J.; Blaylock, B.G.; Boston, H.L.; Huston, M.A.; Kimmel, B.L.; Smith, J.G.; Southworth, G.R.; Stewart, A.J.; Walton, B.T.; Kitchings, J.T.; Olsen, C.R.

    1991-09-01

    On April 1, 1986, a National Pollutant Discharge Elimination System (NPDES) permit was issued for the Oak Ridge National Laboratory (ORNL) (EPA 1986). As specified in Part 3: Special Conditions (Item H) of the permit, a plan for biological monitoring of the Clinch River, White Oak Creek (WOC), Northwest Tributary (NWT) of WOC, Melton Branch (MB), Fifth Creek, and First Creek shall be submitted for approval to the US Environmental Protection Agency (EPA) and the Tennessee Department of Health and Environment (TDHE) within 90 days of the effective date of the permit. The plan, which is referred to in Part 3 (H) of the permit as the Biological Monitoring Plan and Abatement Program (BMPAP), describes characterization monitoring studies to be conducted for the duration of the permit (5 years). In order to be consistent with the terminology used for the Biological Monitoring and Abatement Programs for the Oak Ridge Y-12 Plan and the Oak Ridge K-25 Plant, BMPAP will subsequently be referred to as the Biological Monitoring and Abatement Program (BMAP). The proposed BMAP outlined in this document is based on preliminary discussions held on December 9, 1985, between staff of Martin Marietta Energy Systems, Inc. (ORNL and Central Management), the US Department of Energy (DOE), EPA, and TDHE. 232 refs., 11 figs., 7 tabs.

  17. FINAL DESIGN OF ILC RTML EXTRACTION LINE FOR SINGLE STAGE BUNCH COMPRESSOR

    SciTech Connect (OSTI)

    Seletskiy, S.; Solyak, N.

    2011-03-28

    The use of single stage bunch compressor (BC) in the International Linear Collider (ILC) Damping Ring to the Main Linac beamline (RTML) requires new design for the extraction line (EL). The EL located downstream of the BC will be used for both an emergency abort dumping of the beam and the tune-up continuous train-by-train extraction. It must accept both compressed and uncompressed beam with energy spread of 3.54% and 0.15% respectively. In this paper we report the final design that allowed minimizing the length of such extraction line while offsetting the beam dumps from the main line by 5m distance required for acceptable radiation level in the service tunnel. Proposed extraction line can accommodate beams with different energy spreads at the same time providing the beam size suitable for the aluminum ball dump window. We described the final design of the ILC RTML extraction line located downstream of the new single-stage bunch compressor. The extraction line is only 24m long and is capable of accepting and transmitting 220kW of beam power. The EL can be used for both fast intra-train and continual extraction, and is capable of accepting both 0.15% and 3.54% energy spread beams at 5MeV and 4.37MeV respectively.

  18. Viscous throughflow modeling of axial compressor bladerows using a tangential blade force hypothesis

    SciTech Connect (OSTI)

    Gallimore, S.J.

    1998-10-01

    This paper describes the modeling of axial compressor blade rows in an axisymmetric viscous throughflow method. The basic method, which has been reported previously, includes the effects of spanwise mixing, using a turbulent diffusion model, and endwall shear within the throughflow calculation. The blades are modeled using a combination of existing two-dimensional blade performance predictions for loss and deviation away from the annulus walls and a novel approach using tangential blade forces in the endwall regions. Relatively simple assumptions about the behavior of the tangential static pressure force imposed by the blades allow the secondary deviations produced by tip clearance flows and the boundary layer flows at fixed blade ends to be calculated in the axisymmetric model. Additional losses are assigned in these regions based on the calculated deviations. The resulting method gives realistic radial distributions of loss and deviation across the whole span at both design and off-design operating conditions, providing a quick method of estimating the magnitudes of these effects in the preliminary design process. Results from the method are compared to measured data in low and high-speed compressors and multistage three-dimensional viscous CFD predictions.

  19. Numerical simulation of the compressor coil of the plasma dynamic accelerator

    SciTech Connect (OSTI)

    Thomas, P.

    1997-01-01

    The plasma dynamic accelerator accelerates a plasma to very high velocities in a coaxial accelerator and then compresses it in a compressor coil, achieving high densities. The axial component of the current distribution, extending from the tip of the coaxial accelerator`s center electrode to the coil turns, causes compressing forces, the radial component yields accelerating forces. The rapid change of the coil current induces azimuthal eddy currents in the plasma that interact with the coil`s magnetic field, again yielding Lorentz forces. Aerodynamic compression may also be an important effect. A new two-dimensional magnetohydrodynamics code is used to investigate which of these effects are really important for the compression. The code allows one to simulate all effects mentioned separately and in combination. In a first step only aerodynamic compression is considered. Then each electromagnetic effect is imposed on the system. Finally, a complete simulation of the compressor coil is performed. The analysis of the results provides new insights in the way the coil operates. This paper presents important aspects of the mathematical model and of the numerical implementation and reports results.

  20. Phase I remedial investigation report of Waste Area Grouping 2 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Miller, D.E. [ed.

    1995-07-01

    This report presents the activities and findings of the first phase of a three-phase remedial investigation (RI) of Waste Area Grouping (WAG) 2 at Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee, and updates the scope and strategy for WAG-2-related efforts. WAG 2 contains White Oak Creek (WOC) and its tributaries downstream of the ORNL main plant area, White Oak Lake, White Oak Creek Embayment on the Clinch River, and the associated floodplain and subsurface environment. Water, sediment, soil, and biota in WAG 2 are contaminated and continue to receive contaminants from upgradient WAGs. This report includes field activities completed through October 1992. The remediation of WAG 2 is scheduled to follow the cessation of contaminant input from hydrologically upgradient WAGs. While upgradient areas are being remediated, the strategy for WAG 2 is to conduct a long-term monitoring and investigation program that takes full advantage of WAG 2`s role as an integrator of contaminant fluxes from other ORNL WAGs and focuses on four key goals: (1) Implement, in concert with other programs, long-term, multimedia environmental monitoring and tracking of contaminants leaving other WAGs, entering WAG 2, and being transported off-site. (2) Provide a conceptual framework to integrate and develop information at the watershed-level for pathways and processes that are key to contaminant movement, and so support remedial efforts at ORNL. (3) Provide periodic updates of estimates of potential risk (both human health and ecological) associated with contaminants accumulating in and moving through WAG 2 to off-site areas. (4) Support the ORNL Environmental Restoration Program efforts to prioritize, remediate, and verify remedial effectiveness for contaminated sites at ORNL, through long-term monitoring and continually updated risk assessments.

  1. Environmental Monitoring Plan for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1993-09-01

    This document presents the Environmental Monitoring Plan (EMP) for Waste Area Grouping (WAG) 6 at the Oak Ridge National Laboratory (ORNL). Based on the results of the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) and on subsequent discussions with regulators, a decision was made to defer implementing source control remedial measures at the WAG. The alternative selected to address the risks associated with WAG 6 involves maintenance of site access controls prevent public exposure to on-site contaminants, continued monitoring of contaminant releases determine if source control measures are required, and development of technologies that could support the final remediation of WAG 6. Although active source control measures are not being implemented at WAG 6, environmental monitoring is necessary to ensure that any potential changes in contaminant release from the WAG are identified early enough to take appropriate action. Two types of environmental monitoring will be conducted: baseline monitoring and annual routine monitoring. The baseline monitoring will be conducted to establish the baseline contaminant release conditions at the WAG, confirm the site-related chemicals of concern (COCs), and gather data to confirm the site hydrologic model. The baseline monitoring is expected to begin in 1994 and last for 12--18 months. The annual routine monitoring will consist of continued sampling and analyses of COCs to determine off-WAG contaminant flux and risk, identify mills in releases, and confirm the primary contributors to risk. The annual routine monitoring will continue for {approximately} 4 years after completion of the baseline monitoring.

  2. Environmental monitoring plan for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    1995-09-01

    This document presents an Environmental Monitoring Plan (EMP) for Waste Area Grouping (WAG 6) at Oak Ridge National Laboratory (ORNL). This document updates a draft monitoring plan developed in 1993. The draft plan was never finalized awaiting resolution of the mechanisms for addressing RCRA concerns at a site where the CERCLA process resulted in a decision to defer action, i.e., postpone closure indefinitely. Over the past two years the Tennessee Department of Environment and Conservation (TDEC), US Department of Energy (DOE), and US Environmental Protection Agency (EPA) Region IV, have agreed that RCRA authority at the site will be maintained through a post- closure permit; ``closure`` in this case referring to deferred action. Both a Revised Closure Plan (DOE 1995a) and a Post-Closure Permit Application (DOE 1995b) have been developed to document this agreement; relevant portions of the EMP will be included in the RCRA Post-Closure Permit Application. As the RCRA issues were being negotiated, DOE initiated monitoring at WAG 6. The purpose of the monitoring activities was to (1) continue to comply with RCRA groundwater quality assessment requirements, (2) install new monitoring equipment, and (3) establish the baseline conditions at WAG 6 against which changes in contaminant releases could be measured. Baseline monitoring is scheduled to end September 30, 1995. Activities that have taken place over the past two years are summarized in this document.

  3. Environmental Survey preliminary report, Oak Ridge Gaseous Diffusion Plant, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1989-02-01

    This report presents the preliminary findings from the first phase of the Environmental Survey of the US Department of Energy's (DOE) Oak Ridge Gaseous Diffusion Plant (ORGDP) conducted March 14 through 25, 1988. The Survey is being conducted by an interdisciplinary team of environmental specialists, led and managed by the Office of Environment, Safety and Health's Office of Environmental Audit. Individual team components are being supplied by a private contractor. The objective of the Survey is to identify environmental risk associated with ORGDP. The Survey covers all environmental media and all areas of environmental regulation. It is being performed in accordance with the DOE Environmental Survey Manual. This phase of the Survey involves the review of existing site environmental data, observations of the operations carried on at ORGDP, and interviews with site personnel. The Survey team developed a Sampling and Analysis Plan to assist in further assessing certain of the environmental problems identified during is on-site activities. The Sampling and Analysis Plan will be executed by Idaho National Engineering Laboratory (INEL). When completed, the results will be incorporated into the ORGDP Survey findings for in inclusion into the Environmental Survey Summary Report. 120 refs., 41 figs., 74 tabs.

  4. Underground storage tank management plan, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    1997-09-01

    The Underground Storage Tank (UST) Program at the Oak Ridge Y-12 Plant was established to locate UST systems at the facility and to ensure that all operating UST systems are free of leaks. UST systems have been removed or upgraded in accordance with Tennessee Department of Environment and Conservation (TDEC) regulations and guidance. With the closure of a significant portion of the USTs, the continuing mission of the UST Management Program is to manage the remaining active UST systems and continue corrective actions in a safe regulatory compliant manner. This Program outlines the compliance issues that must be addressed, reviews the current UST inventory and compliance approach, and presents the status and planned activities associated with each UST system. The UST Program provides guidance for implementing TDEC regulations and guidelines for petroleum UST systems. The plan is divided into three major sections: (1) regulatory requirements, (2) active UST sites, and (3) out-of-service UST sites. These sections describe in detail the applicable regulatory drivers, the UST sites addressed under the Program, and the procedures and guidance for compliance.

  5. Environmental Survey preliminary report, Oak Ridge National Laboratory (X-10), Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1988-07-01

    This report presents the preliminary findings from the first phase of the Environmental Survey of the US Department of Energy (DOE) Oak Ridge National Laboratory (ORNL), X-10 site, conducted August 17 through September 4, 1987. The Survey is being conducted by an interdisciplinary team of environmental specialists, led and managed by the Office of Environment, Safety and Health's Office of Environmental Audit. Individual team specialists are outside experts supplied by a private contractor. The objective of the Survey is to identify environmental problems and areas of environmental risk associated with ORNL. The Survey covers all environmental media and all areas of environmental regulation. It is being performed in accordance with the DOE Environmental Survey Manual. The on-site phase of the Survey involves the review of existing site environmental data, observations of the operations carried on at ORNL, and interviews with site personnel. The Survey team developed a Sampling and Analysis Plan to assist in further assessing certain of the environmental problems identified during its on-site activities. The Sampling and Analysis Plan will be executed by a DOE National Laboratory or a support contractor. When completed, the results will be incorporated into the Environmental Survey Interim Report for ORNL. The Interim Report will reflect the final determinations of the ORNL Survey. 120 refs., 68 figs., 71 tabs.

  6. Removal site evaluation report for the Isotope Facilities at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    1996-07-01

    This removal site evaluation (RmSE) report of the Isotope Facilities at Oak Ridge National Laboratory (ORNL) was prepared to provide the Environmental Restoration Program with information necessary to evaluate whether hazardous and/or radiological contaminants in and around the Isotopes Facility pose a substantial risk to human health or the environment and if remedial site evaluations (RSEs) or removal actions are required. The scope of the project included: (1) a review of historical evidence regarding operations and use of the facility; (2) interviews with facility personnel concerning current and past operating practices; (3) a site inspection; and (4) identification of hazard areas requiring maintenance, removal, or remedial actions. The results of RmSE indicate that no substantial risks exist from contaminants present in the Isotope Facilities because adequate controls and practices exist to protect human health and the environment. The recommended correction from the RmSE are being conducted as maintenance actions; accordingly, this RmSE is considered complete and terminated.

  7. Mechanical energy storage in carbon nanotube springs

    E-Print Network [OSTI]

    Hill, Frances Ann

    2011-01-01

    Energy storage in mechanical springs made of carbon nanotubes is a promising new technology. Springs made of dense, ordered arrays of carbon nanotubes have the potential to surpass both the energy density of electrochemical ...

  8. Motor gasoline assessment, Spring 1997

    SciTech Connect (OSTI)

    NONE

    1997-07-01

    The springs of 1996 and 1997 provide an excellent example of contrasting gasoline market dynamics. In spring 1996, tightening crude oil markets pushed up gasoline prices sharply, adding to the normal seasonal gasoline price increases; however, in spring 1997, crude oil markets loosened and crude oil prices fell, bringing gasoline prices down. This pattern was followed throughout the country except in California. As a result of its unique reformulated gasoline, California prices began to vary significantly from the rest of the country in 1996 and continued to exhibit distinct variations in 1997. In addition to the price contrasts between 1996 and 1997, changes occurred in the way in which gasoline markets were supplied. Low stocks, high refinery utilizations, and high imports persisted through 1996 into summer 1997, but these factors seem to have had little impact on gasoline price spreads relative to average spread.

  9. Dr. Campbell's Bio111 Exam #3 Spring 2007 Spring 2007 Biology 111 Take Home Exam #3 BioEnergetics

    E-Print Network [OSTI]

    Campbell, A. Malcolm

    Dr. Campbell's Bio111 Exam #3 ­ Spring 2007 1 Spring 2007 Biology 111 Take Home Exam #3 ­ BioEnergetics

  10. Dr. Campbell's Bio111 Exam #3 Spring 2008 Spring 2008 Biology 111 Take Home Exam #3 BioEnergetics

    E-Print Network [OSTI]

    Campbell, A. Malcolm

    Dr. Campbell's Bio111 Exam #3 ­ Spring 2008 1 Spring 2008 Biology 111 Take Home Exam #3 ­ BioEnergetics

  11. National School on Neutron and X-ray Scattering Oak Ridge National Laboratory June 12-26, 2010 Oak Ridge, Tennessee

    E-Print Network [OSTI]

    Pennycook, Steve

    National School on Neutron and X-ray Scattering Oak Ridge National Laboratory June 12-26, 2010 Oak:30 Lecture Inelastic Neutron Scattering B. D. Gaulin McMaster University Lecture Magnetic Scattering B. D Break Break Break Break 9:45 - 10:45 Lecture Continued Inelastic Neutron Scattering B. D. Gaulin Mc

  12. Spring 10 Spring 11 Spring 12 Spring 13 Overall 20,402 21,091 21,354 20,642

    E-Print Network [OSTI]

    Memphis, University of

    -time Freshmen Cohorts Female Male Average online 16% on-ground 84% Spring 2013 Credit Hour Generation 0 500 1

  13. Spring 2014 Composite Data Products: Backup Power

    SciTech Connect (OSTI)

    Kurtz, J.; Sprik, S.; Saur, G.

    2014-06-01

    This report includes 30 composite data products (CDPs) produced in Spring 2014 for fuel cell backup power systems.

  14. Experimental Study of Heat Transfer Enhancement in a Liquid Piston Compressor/Expander Using Porous Media Inserts

    E-Print Network [OSTI]

    Li, Perry Y.

    or a compressor for compressed natural gas (CNG). Highlights · Porous medias role to improve compres- sor is the predominant contribution to im- provements Keywords: Liquid piston, porous media, gas compression / expansion combined with natural gas in a gas turbine to boost9 combustion e ciency. As a storage device, its e -10

  15. Abstract--For a Compressed Air Energy Storage (CAES) approach to be viable, the air compressor/expander must be

    E-Print Network [OSTI]

    Li, Perry Y.

    Abstract-- For a Compressed Air Energy Storage (CAES) approach to be viable, the air compressor (CAES) system for offshore wind turbine has been proposed in [1, 2] (Fig. 1). It uses the open Storage (CAES) System for Offshore Wind Turbine Although the heat transfer models above are reasonable

  16. Cold Spring Harbor Laboratory Cold Spring Harbor Laboratory

    E-Print Network [OSTI]

    and educational institution founded 1890 980 staff members Seven divisions ·Research (cancer, neuroscience, plant, located at Cold Spring Harbor, Plymouth (UK), Tuebingen (Germany) and San Diego. Over 200 books in print ·Finding appropriate authors/editors for new books ·Preparing a proposal for the book ·Outline / Table

  17. Oak Ridge K-25 Site Technology Logic Diagram

    SciTech Connect (OSTI)

    Fellows, R.L. (ed.)

    1993-02-26

    The Oak Ridge K-25 Technology Logic Diagram (TLD), a decision support tool for the K-25 Site, was developed to provide a planning document that relates environmental restoration and waste management problems at the Oak Ridge K-25 Site to potential technologies that can remediate these problems. The TLD technique identifies the research necessary to develop these technologies to a state that allows for technology transfer and application to waste management, remedial action, and decontamination and decommissioning activities. The TLD consists of four separate volumes-Vol. 1, Vol. 2, Vol. 3A, and Vol. 3B. Volume 1 provides introductory and overview information about the TLD. Volume 2 contains logic diagrams. Volume 3 has been divided into two separate volumes to facilitate handling and use. This report is part A of Volume 3 concerning characterization, decontamination, and dismantlement.

  18. Oak Ridge Environmental Information System (OREIS) Enhancements - 13109

    SciTech Connect (OSTI)

    Halsey, Patricia J. [U.S. Department of Energy, Office of Environmental Management, Oak Ridge, TN 37830 (United States)] [U.S. Department of Energy, Office of Environmental Management, Oak Ridge, TN 37830 (United States); Salpas, Peter A. [Salpas Consulting, Inc., 106 Claymore Ln, Oak Ridge, TN 37830 (United States)] [Salpas Consulting, Inc., 106 Claymore Ln, Oak Ridge, TN 37830 (United States); Clark, Phillip A.; Lewis, Larry [Restoration Services, Inc., P.O. Box 5177, Oak Ridge, TN 37831 (United States)] [Restoration Services, Inc., P.O. Box 5177, Oak Ridge, TN 37831 (United States); Tharpe, Deidre

    2013-07-01

    Significant cleanup has been accomplished on the Oak Ridge (OR) site since it was placed on the National Priorities List (NPL) in 1989, and a final evaluation of Zone 1 at the East Tennessee Technology Park (ETTP) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1988 (CERCLA) has been initiated. The Oak Ridge Environmental Information System (OREIS) is the database for storing OR site environmental characterization and monitoring data. Consideration of a final decision under CERCLA prompted several enhancements to OREIS that were designed to provide future users a clear picture of remediation progression across the OR site. The enhancements to OREIS are ongoing and fall into four categories: Geographic Information System Interface; Document Association; Remediation Status; Geo-spatial Data (authors)

  19. A study of shin oak (Quercus havardi) poisoning in cattle 

    E-Print Network [OSTI]

    Dollahite, James Walton

    1961-01-01

    Dried 3-5 days 6 Lost, 6 Died g days later TABLE 2. Feeding Shin Oak oo Sheep. Wt, ~lbs. ) Stage of' growth Amount Days of oak fed(lbs, . ) fed Result- Fresh blossoms, buds? leaves 20 Lost 19$ 301 Fresh blossoms, buds, leaves 39 21 Lost 23k... Enteritis Died No visible lesions !Bi)ie 5 tw nt '. *I)Bio) AII1IBB t 'no?j km o Bn t Days Ded (, gms, ) Ded I', eso11B !I)50 JU . 0 20 ' Bl l!' i' ve . ?Bast):)en I 61 1 I i lve. Bild k' 'I . 'i;. ')' dit'K?ga i:ve dar k) gBB. ?":. , nt. e. Live...

  20. Native Grass Community Management Plan for the Oak Ridge Reservation

    SciTech Connect (OSTI)

    Ryon, Michael G [ORNL; Parr, Patricia Dreyer [ORNL; Cohen, Kari [ORNL

    2007-06-01

    Land managers at the Department of Energy's Oak Ridge National Laboratory in East Tennessee are restoring native warm-season grasses and wildflowers to various sites across the Oak Ridge Reservation (ORR). Some of the numerous benefits to planting native grasses and forbs include improved habitat quality for wildlife, improved aesthetic values, lower long-term maintenance costs, and compliance with Executive Order 13112 (Clinton 1999). Challenges to restoring native plants on the ORR include the need to gain experience in establishing and maintaining these communities and the potentially greater up-front costs of getting native grasses established. The goals of the native grass program are generally outlined on a fiscal-year basis. An overview of some of the issues associated with the successful and cost-effective establishment and maintenance of native grass and wildflower stands on the ORR is presented in this report.

  1. Status report: A hydrologic framework for the Oak Ridge Reservation

    SciTech Connect (OSTI)

    Solomon, D.K.; Toran, L.E.; Dreier, R.B.; Moore, G.K.; McMaster, W.M.

    1992-05-01

    This first status report on the Hydrologic Studies Task of the Oak Ridge Reservation Hydrology and Geology Study (ORRHAGS) revises earlier concepts of subsurface hydrology and hydrogeochemistry of the ORR. A new classification of hydrogeologic units is given, as well as new interpretations of the gydrogeologic properties and processes that influence contaminant migration. The conceptual hydrologic framework introduced in this report is based primarily on reinterpretations of data acquired during earlier hydrologic investigations of waste areas at and near the three US Department of Energy Oak Ridge (DOE-OR) plant facilities. In addition to describing and interpreting the properties and processes of the groundwater systems as they are presently understood, this report describes surface water-subsurface water relations, influences on contaminant migration,and implications to environmental restoration, environmental monitoring, and waste management.

  2. Environmental Monitoring Plan for the Oak Ridge Reservation, 2012

    SciTech Connect (OSTI)

    Thompson, Sharon D.

    2012-10-01

    The purpose of Oak Ridge Reservation (ORR) environmental surveillance is to characterize radiological and nonradiological conditions of the off-site environs and estimate public doses related to these conditions, confirm estimations of public dose based on effluent monitoring data, and, where appropriate, provide supplemental data to support compliance monitoring for applicable environmental regulations. This environmental monitoring plan (EMP) is intended to document the rationale, frequency, parameters, and analytical methods for the ORR environmental surveillance program and provides information on ORR site characteristics, environmental pathways, dose assessment methods, and quality management. ORR-wide environmental monitoring activities include a variety of media including air, surface water, vegetation, biota, and wildlife. In addition to these activities, site-specific effluent, groundwater, and best management monitoring programs are conducted at the Oak Ridge National Laboratory (ORNL), the Y-12 National Security Complex (Y-12), and the East Tennessee Technology Park (ETTP). This is revision 5.

  3. Oak Ridge K-25 Site Technology Logic Diagram

    SciTech Connect (OSTI)

    Fellows, R.L.

    1993-02-26

    The Oak Ridge K-25 Technology Logic Diagram (TLD), a decision support tool for the K-25 Site, was developed to provide a planning document that relates envirorunental restoration and waste management problems at the Oak Ridge K-25 Site to potential technologies that can remediate these problems. The TLD technique identifies the research necessary to develop these technologies to a state that allows for technology transfer and application to waste management, remedial action, and decontamination and decommissioning activities. The TLD consists of four separate volumes-Vol. 1, Vol. 2, Vol. 3A, and Vol. 3B. Volume 1 provides introductory and overview information about the TLD. This volume, Volume 2, contains logic diagrams with an index. Volume 3 has been divided into two separate volumes to facilitate handling and use.

  4. Design and development of a four-cell sorption compressor based J-T cooler using R134a as working fluid

    SciTech Connect (OSTI)

    Mehta, R. N.; Bapat, S. L.; Atrey, M. D.

    2014-01-29

    The need of a cooler with no electromagnetic interference and practically zero vibration has led to sorption compressor based Joule-Thomson (J-T) coolers. These are useful for sophisticated electronic, ground based and space borne systems. In a Sorption compressor, adsorbed gases are desorbed into a confined volume by raising temperature of the sorption bed resulting in an increase in pressure of the liberated gas. In order to have the system (compressor) functioning on a continuous basis, with almost a constant gas flow rate, multiple cells are used with the adaptation of Temperature Swing Adsorption (TSA) process. As the mass of the desorbed gas dictates the compressor throughput, a combination of sorbent material with high adsorption capacity for a chosen gas or gas mixture has to be selected for efficient operation of the compressor. Commercially available (coconut-shell base) activated carbon has been selected for the present application. The characterization study for variation of discharge pressure is used to design the Four-cell sorption compressor based cryocooler with a desired output. Apart from compressor, the system includes a) After cooler b) Return gas heat exchanger c) capillary tube as the J-T expansion device and d) Evaporator.

  5. Technology study of Gunite tank sludge mobilization at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    DeVore, J.R.; Herrick, T.J.; Lott, K.E.

    1994-12-01

    The Oak Ridge National Laboratory (ORNL) Gunite Tank Sludge Mobilization Technology Study was initiated to support the Gunite Tank Treatability Study effort. The technology study surveyed the methods and technologies available for tank cleaning and sludge mobilization in a radioactive environment. Technologies were identified and considered for applicability to the Gunite and Associated Tanks (GAAT) problems. These were then either accepted for further study or rejected as not applicable. Technologies deemed applicable to the GAAT sludge removal project were grouped for evaluation according to (1) deployment method, (2) types of remotely operated end effector equipment applicable to removal of sludge, (3) methods for removing wastes from the tanks, and (4) methods for concrete removal. There were three major groups of deployment technologies: ``past practice`` technologies, mechanical arm-based technologies, and vehicle-based technologies. The different technologies were then combined into logical sequences of deployment platform, problem, end effector, conveyance, post-removal treatment required (if any), and disposition of the waste. Many waste removal options are available, but the best technology in one set of circumstances at one site might not be the best type to use at a different site. No single technology is capable of treating the entire spectrum of wastes that will be encountered in GAAT. None of the systems used in other industries appears to be suitable, primarily because of the nature of the sludges in the GAAT Operable Unit (OU), their radiation levels, and tank geometries. Other commercial technologies were investigated but rejected because the authors did not believe them to be applicable.

  6. Oak Ridge Reservation annual site environmental report for 2008

    SciTech Connect (OSTI)

    none,

    2009-09-01

    The Oak Ridge Reservation (ORR) consists of three major government-owned, contractor-operated facilities: the Y-12 National Security Complex, Oak Ridge National Laboratory, and East Tennessee Technology Park. The ORR was established in the early 1940s as part of the Manhattan Project, a secret undertaking that produced materials for the first atomic bombs. The reservation’s role has evolved over the years, and it continues to adapt to meet the changing defense, energy, and research needs of the United States. Both the work carried out for the war effort and subsequent research, development, and production activities have involved, and continue to involve, the use of radiological and hazardous materials. The Oak Ridge Reservation Annual Site Environmental Report and supporting data are available at http://www.ornl.gov/sci/env_rpt or from the project director. This document is prepared annually to summarize environmental activities, primarily environmental monitoring activities, on the Oak Ridge Reservation (ORR) and within the ORR surroundings. The document fulfills the requirement of Department of Energy (DOE) Order 231.1A, Environment, Safety and Health Reporting, for an annual summary of environmental data to characterize environmental performance. The environmental monitoring criteria are described in DOE Order 450.1A, Environmental Protection Program. The results summarized in this report are based on data collected prior to and through 2008. This report is not intended to provide the results of all sampling on the ORR. Additional data collected for other site and regulatory purposes, such as environmental restoration/remedial investigation reports, waste management characterization sampling data, and environmental permit compliance data, are presented in other documents that have been prepared in accordance with applicable DOE guidance and/or laws and are referenced herein as appropriate. Corrections to the report for the previous year are found in Appendix A. Appendix B contains a glossary of technical terms that may be useful for clarifying some of the language used in this document.

  7. SNS Experimental Facilities Oak Ridge SNS Mercury Target Issues and

    E-Print Network [OSTI]

    McDonald, Kirk

    Factory Hg Target w/ 2 MW Proton Beam (time-averaged) Volumetric Heating Rate (MW/m 3 ) 10-2 10-1 1 10 103 Inventory 1.4 m 3 (20 tons) · Pump Power 56 kW (75 HP) #12;SNS Experimental Facilities Oak Ridge9 Hg Process Loop Collection Tank Pump Storage Tank Heat Exchanger Target Water Delay Tank Gas Liquid Separator

  8. Oak Ridge National Laboratory Review. Volume 25, No. 1, 1992

    SciTech Connect (OSTI)

    Krause, C.; Pearce, J.; Zucker, A.

    1992-10-01

    This report presents brief descriptions of the following programs at Oak Ridge National Laboratory: The effects of pollution and climate change on forests; automation to improve the safety and efficiency of rearming battle tanks; new technologies for DNA sequencing; ORNL probes the human genome; ORNL as a supercomputer research center; paving the way to superconcrete made with polystyrene; a new look at supercritical water used in waste treatment; and small mammals as environmental monitors.

  9. Shrub Oak, New York: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page| Open Energy Information Serbia-Enhancing Capacity for LowInformationShoshone County, Idaho:Shreveport,Shrub Oak,

  10. Oak Ridge Site Specific Advisory Board Committees | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankADVANCED MANUFACTURINGEnergy Bills and ReduceNovember 2014Marketing2014) |D DOak RidgeCommittees Oak

  11. EM's Oak Ridge Office Launches New Website | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:FinancingPetroleum Based|DepartmentStatementof EnergyQuality'Lean' System |Oak Ridge Office

  12. Highlights of Spring 2011 Environmental

    E-Print Network [OSTI]

    Niebur, Ernst

    Highlights of Spring 2011 Environmental Politics and Policy Political and International Relations Theory Spotlight: The Middle East Beltway Politics and American Ideals Issues in International Our Planet Emma Huvos Political Science Class of 2013 The American Dream: One Size Fits All Maxi

  13. DEAN'S LIST Spring Semester 2010

    E-Print Network [OSTI]

    Wong, Pak Kin

    DEAN'S LIST Spring Semester 2010 Chai, Jun Christopher, Joseph Thomas Chu, Clayton N. Chu, Wesley D. Cook, Nathan I. Cordon, Michael J. Danford, Forest L. Davenport, Andrew Edward Davis, Amanda Kathryn. Bloom, John Tyler Bond-Choquette, Claire Marie Bradford, Jonathan W. Brown, Thomas C. Bruns, Jared M

  14. Mesoscale Dynamics Spring Semester 2014

    E-Print Network [OSTI]

    Collett Jr., Jeffrey L.

    ATS 735 Mesoscale Dynamics (3 cr) Spring Semester 2014 Instructor: Richard H. Johnson, Room ATS 305: There are no required texts. The recent book Mesoscale Meteorology in Midlatitudes by Markowski and Richardson covers with mesoscale-related research. A set of notes will be made available for the course, although we will not cover

  15. Mesoscale Modeling Spring Semester 2014

    E-Print Network [OSTI]

    van den Heever, Susan C.

    ATS730 Mesoscale Modeling Spring Semester 2014 Meeting Times: T/TH: 9-10:15am Room: ATS 101 is to present the development of the basic equations used in mesoscale models, as well as the various methods than on actual simulations of mesoscale phenomena or the evaluation of specific mesoscale models

  16. Spring 2015 Biochemistry Department Courses

    E-Print Network [OSTI]

    Vaccaro, Joe

    Spring 2015 Biochemistry Department Courses Course Number CRN Title Instructor Credits Days Time:00-10:50 5150 Elective Required GBCH-7520 24367 Human Medical Metabolic Biochemistry Franklin 5 T Th 3:30 - 5 GBCH-6110 26581 Basic Medical Biochemistry Landry 3 MWF 3:00-3:50 6065 Elective Master's Research

  17. Spring 2014 Organization Development & Training

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Spring 2014 Organization Development & Training Catalog University of Central Florida Office of Organization Development & Training 3280 Progress Drive Orlando, FL 32826-2912 (407) 823-0440 February 7, 2014 Volume 2, Number 3 The current Catalog is published at http://www.hr.ucf.edu/web/training

  18. RESEARCH IN ACCOUNTING SPRING 2015

    E-Print Network [OSTI]

    1 RESEARCH IN ACCOUNTING SPRING 2015 Bikki Jaggi 848-445-3539 E-Mail: Jaggi financial accounting issues and to acquaint them with various research methodologies used in empirical financial accounting research. A number of financial accounting topics are selected for presentation

  19. Chemistry Department Colloquium: Spring, 2012

    E-Print Network [OSTI]

    Sheridan, Jennifer

    Chemistry Department Colloquium: Spring, 2012 Friday, March 16; 3:30 Seminar Hall (room 1315 Chemistry) Lost in Translation: How Regulators Use Science and How Scientists Can Help Bridge Gaps Stephanie to combine her Chemistry background with a legal education to improve the use of science in environmental

  20. GG455 --Hydrogeology Spring 2014

    E-Print Network [OSTI]

    conditions · Pore pressure & tension · Aquifers Groundwater Flow · Darcy's law · Hydraulic head & fluid flow Groundwater Flow Applications · Analytic solutions to simple flow problems · Radial flow to wells on availability) 1. Well drilling site 2. Springs 3. Board of Water Supply (BWS) Beretania pump station and Halawa

  1. Spring 2014 Heat Transfer -1

    E-Print Network [OSTI]

    Virginia Tech

    Spring 2014 1 Heat Transfer - 1 Consider a cylindrical nuclear fuel rod of length L and diameter df and the tube at a rate m , and the outer surface of the tube is well insulated. Heat generation occurs within. The specific heat of water pc , and the thermal conductivity of the fuel rod fk are constants. The system

  2. Mesoscale Dynamics Spring Semester 2012

    E-Print Network [OSTI]

    Birner, Thomas

    ATS 735 Mesoscale Dynamics (3 cr) Spring Semester 2012 Instructor: Richard H. Johnson, Room ATS 305: There are no required texts. The recent book Mesoscale Meteorology in Midlatitudes by Markowski and Richardson covers with mesoscale-related research. A set of notes will be made available for the course, although we will not cover

  3. Remedial investigation report on Waste Area Group 5 at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Volume 1: Technical summary

    SciTech Connect (OSTI)

    1995-03-01

    A remedial investigation (RI) was performed to support environmental restoration activities for Waste Area Grouping (WAG) 5 at the Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee. The WAG 5 RI made use of the observational approach, which concentrates on collecting only information needed to assess site risks and support future cleanup work. This information was interpreted and is presented using the framework of the site conceptual model, which relates contaminant sources and release mechanisms to migration pathways and exposure points that are keyed to current and future environmental risks for both human and ecological receptors. The site conceptual model forms the basis of the WAG 5 remedial action strategy and remedial action objectives. The RI provided the data necessary to verify this model and allows recommendations to be made to accomplish those objectives.

  4. Self-latching eccentric cam for dual stroke compressor or pump

    DOE Patents [OSTI]

    Sisk, Francis J. (San Mateo, CA)

    1985-01-01

    For a dual capacity refrigerant compressor of the type which has an eccentric cam rotatable on a crankpin between two opposite positions which changes the total eccentricity of the crankpin and cam so as to obtain two different stroke lengths, the rotation of the cam on the crankpin being effected by a reversal of motor operation, the cam moves through an angle of about 270.degree. around the crankpin so that a centrifugal force torque tending to hold the cam in place is available at least in the reduced stroke length position of the cam, and by providing lightening cavities and eccentric weightings, the center of mass 74 of the cam can be shifted to obtain the centrifugal torque in the proper direction at both the maximum and reduced stroke positions.

  5. Cryogenic Viscous Compressor Development and Modeling for the ITER Vacuum System

    SciTech Connect (OSTI)

    Baylor, Larry R [ORNL; Meitner, Steven J [ORNL; Barbier, Charlotte N [ORNL; Combs, Stephen Kirk [ORNL; Duckworth, Robert C [ORNL; Edgemon, Timothy D [ORNL; Rasmussen, David A [ORNL; Hechler, Michael P [ORNL; Kersevan, R. [ITER Organization, Cadarache, France; Dremel, M. [General Atomics, San Diego; Pearce, R.J.H. [General Atomics, San Diego; Boissin, Jean Claude [Consultant

    2011-01-01

    The ITER vacuum system requires a roughing pump system that can pump the exhaust gas from the torus cryopumps to the tritium exhaust processing plant. The gas will have a high tritium content and therefore conventional vacuum pumps are not suitable. A pump called a cryogenic viscous compressor (CVC) is being designed for the roughing system to pump from ~500 Pa to 10 Pa at flow rates of 200 Pa-m3/ s. A unique feature of this pump is that is allows any helium in the gas to flow through the pump where it is sent to the detritiation system before exhausting to atmosphere. A small scale prototype of the CVC is being tested for heat transfer characteristics and compared to modeling results to ensure reliable operation of the full scale CVC. Keywords- ITER; vacuum; fuel cycle

  6. Dynamics of Longitudinal Phase-Space Modulations in an rf Compressor for Electron Beams

    SciTech Connect (OSTI)

    Venturini, M.; Migliorati, M.; Ronsivalle, C.; Ferrario, M.; Vaccarezza, C.

    2010-05-21

    Free Electron Lasers (FELs) operating in the UV or x-ray radiation spectrum require peak beam currents that are generally higher than those obtainable by present electron sources, thus making bunch compression necessary. Compression, however, may heighten the effects of collective forces and degrade the beam quality. In this paper they provide a framework for investigating some of these effects in rf compressors by focusing on the longitudinal dynamics of small-amplitude density perturbations, which have the potential to cause the disruptive appearance of the so-called microbunching instability. They develop a linear theory valid for low-to-moderate compression factors under the assumption of a 1D impedance model of longitudinal space charge and provide validation against macroparticle simulations.

  7. High-Power Plasma Switch for 11.4 GHz Microwave Pulse Compressor

    SciTech Connect (OSTI)

    Jay L. Hirshfield

    2010-03-04

    Results obtained in several experiments on active RF pulse compression at X-band using a magnicon as the high-power RF source are presented. In these experiments, microwave energy was stored in high-Q TE01 and TE02 modes of two parallel-fed resonators, and then discharged using switches activated with rapidly fired plasma discharge tubes. Designs and high-power tests of several versions of the compressor are described. In these experiments, coherent pulse superposition was demonstrated at a 5–9 MW level of incident power. The compressed pulses observed had powers of 50–70 MW and durations of 40–70 ns. Peak power gains were measured to be in the range of 7:1–11:1 with efficiency in the range of 50–63%.

  8. Measurement and computation of heat transfer in high-pressure compressor drum geometries with axial throughflow

    SciTech Connect (OSTI)

    Long, C.A.; Morse, A.P.; Tucker, P.G.

    1997-01-01

    This paper makes comparisons between CFD computations and experimental measurements of heat transfer for the axial throughflow of cooling air in a high-pressure compressor spool rig and a plane cavity rig. The heat transfer measurements are produced using fluxmeters and by the conduction solution method from surface temperature measurements. Numerical predictions are made by solving the Navier-Stokes equations in a full three-dimensional, time-dependent form using the finite-volume method. Convergence is accelerated using a multigrid algorithm and turbulence modeled using a simple mixing length formulation. Notwithstanding systematic differences between the measurements and the computations, the level of agreement can be regarded as promising in view of the acknowledged uncertainties in the experimental data, the limitations of the turbulence model and, perhaps more importantly, the modest grid densities used for the computations.

  9. Heat pump employing optimal refrigerant compressor for low pressure ratio applications

    DOE Patents [OSTI]

    Ecker, Amir L. (Dallas, TX)

    1982-01-01

    What is disclosed is a heat pump apparatus for conditioning a fluid characterized by a fluid handler for circulating the fluid in heat exchange relationship with a refrigerant fluid; two refrigerant heat exchangers; one for effecting the heat exchange with the fluid and a second refrigerant-heat exchange fluid heat exchanger for effecting a low pressure ratio of compression of the refrigerant; a rotary compressor for compressing the refrigerant with low power consumption at the low pressure ratio; at least one throttling valve connecting at the inlet side of heat exchanger in which liquid refrigerant is vaporized; a refrigerant circuit serially connecting the above elements; refrigerant in the circuit; a source of heat exchange fluid; heat exchange fluid circulating device and heat exchange fluid circuit for circulating the heat exchange fluid in heat exchange relationship with the refrigerant.

  10. Self-latching eccentric cam for dual stroke compressor or pump

    DOE Patents [OSTI]

    Sisk, F.J.

    1985-01-22

    For a dual capacity refrigerant compressor of the type which has an eccentric cam rotatable on a crankpin between two opposite positions which changes the total eccentricity of the crankpin and cam so as to obtain two different stroke lengths, the rotation of the cam on the crankpin being effected by a reversal of motor operation, the cam moves through an angle of about 270[degree] around the crankpin so that a centrifugal force torque tending to hold the cam in place is available at least in the reduced stroke length position of the cam, and by providing lightening cavities and eccentric weightings, the center of mass of the cam can be shifted to obtain the centrifugal torque in the proper direction at both the maximum and reduced stroke positions. 7 figs.

  11. RCRA Facility Investigation report for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1991-09-01

    This report presents compiled information concerning a facility investigation of waste area group 6(WAG-6), of the solid waste management units (SWMU's) at Oak Ridge National Laboratory (ORNL). The WAG is a shallow ground disposal area for low-level radioactive wastes and chemical wastes. The report contains information on hydrogeological data, contaminant characterization, radionuclide concentrations, risk assessment and baseline human health evaluation including a toxicity assessment, and a baseline environmental evaluation.

  12. Phase 2 confirmatory sampling data report, Lower East Fork Poplar Creek, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    1998-01-01

    A Remedial Investigation of East Fork Poplar Creek (EFPC) concluded that mercury is the principal contaminant of concern in the EFPC floodplain. The highest concentrations of mercury were found to be in a visually distinct black layer of soil that typically lies 15 to 30 cm (6 to 12 in.) below the surface. Mercury contamination was found to be situated in distinct areas along the floodplain, and generally at depths > 20 cm (8 in.) below the surface. In accordance with Comprehensive, Environmental Response, Compensation, and Liability Act (CERCLA), a feasibility study was prepared to assess alternatives for remediation, and a proposed plan was issued to the public in which a preferred alternative was identified. In response to public input, the plan was modified and US Department of Energy (DOE) issued a Record of Decision in 1995 committing to excavating all soil in the EFPC floodplain exceeding a concentration of 400 parts per million (ppm) of mercury. The Lower East Fork Poplar Creek (LEFPC) remedial action (RA) focuses on the stretch of EFPC flowing from Lake Reality at the Y-12 Plant, through the city of Oak Ridge, to Poplar Creek on the Oak Ridge Reservation (ORR) and its associated floodplain. Specific areas were identified that required remediation at the National Oceanographic and Atmospheric Administration (NOAA) Site along Illinois Avenue and at the Bruner Site along the Oak Ridge Turnpike. The RA was conducted in two separate phases. Phase 2, conducted from February to October 1997, completed the remediation efforts at the NOAA facility and fully remediated the Bruner Site. During both phases, data were collected to show that the remedial efforts performed at the NOAA and Bruner sites were successful in implementing the Record of Decision and had no adverse impact on the creek water quality or the city of Oak Ridge publicly owned treatment works.

  13. RCRA Facility Investigation report for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1991-09-01

    This report presents compiled information concerning a facility investigation of waste area group 6(WAG-6), of the solid waste management units (SWMU'S) at Oak Ridge National Laboratory (ORNL). The WAG is a shallow ground disposal area for low-level radioactive wastes and chemical wastes. The report contains information on hydrogeological data, contaminant characterization, radionuclide concentrations, risk assessment from doses to humans and animals and associated cancer risks, exposure via food chains, and historical data. (CBS)

  14. EIS-0110: Central Waste Disposal Facility for Low-Level Radioactive Waste, Oak Ridge Reservation, Oak Ridge, Tennessee

    Broader source: Energy.gov [DOE]

    This EIS assessed the environmental impacts of alternatives for the disposal of low-level waste and by-product materials generated by the three major plants on the Oak Ridge Reservation (ORR). In addition to the no-action alternative, two classes of alternatives were evaluated: facility design alternatives and siting alternatives. This project was cancelled after the Draft Environmental Impact Statement was issued.

  15. Results of 1995 characterization of Gunite and Associated Tanks at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    NONE

    1996-02-01

    This technical memorandum (TM) documents the 1995 characterization of eight underground radioactive waste tanks at Oak Ridge National Laboratory (ORNL). These tanks belong to the Gunite and Associated Tanks (GAAT) operable unit, and the characterization is part of the ongoing GAAT remedial investigation/feasibility study (RI/FS) process. This TM reports both field observations and analytical results; analytical results are also available from the Oak Ridge Environmental Information System (OREIS) data base under the project name GAAT (PROJ-NAME = GAAT). This characterization effort (Phase II) was a follow-up to the {open_quotes}Phase I{close_quotes} sampling campaign reported in Results of Fall 1994 Sampling of Gunite and Associated Tanks at the Oak Ridge National Laboratory, Oak Ridge, Tennessee, ORNL/ER/Sub/87-99053/74, June 1995. The information contained here should be used in conjunction with that in the previous TM. The sampling plan is documented in ORNL Inactive Waste Tanks Sampling and Analysis Plan, ORNL/RAP/LTR-88/24, dated April 1988, as amended by Addendum 1, Revision 2: ORNL Inactive Tanks Sampling and Analysis Plan, DOE/OR/02-1354&D2, dated February 1995. Field team instructions are found in ORNL RI/FS Project Field Work Guides 01-WG-20, Field Work Guide for Sampling of Gunite and Associated Tanks, and 01-WG-21, Field Work Guide for Tank Characterization System Operations at ORNL. The field effort was conducted under the programmatic and procedural umbrella of the ORNL RI/FS Program, and the analysis was in accordance with ORNL Chemical and Analytical Sciences Division (CASD) procedures. The characterization campaign is intended to provide data for criticality safety, engineering design, and waste management as they apply to the GAAT treatability study and remediation. The Department of Energy (DOE) Carlsbad office was interested in results of this sampling campaign and provided funding for certain additional sample collection and analysis.

  16. Work plan for the High Ranking Facilities Deactivation Project at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    1996-03-01

    The High Ranking Facilities Deactivation Project (HRFDP), commissioned by the US Department of Energy Nuclear Materials and Facility Stabilization Program, is to place four primary high-risk surplus facilities with 28 associated ancillary facilities at Oak Ridge National Laboratory in a safe, stable, and environmentally sound condition as rapidly and economically as possible. The facilities will be deactivated and left in a condition suitable for an extended period of minimized surveillance and maintenance (S and M) prior to decontaminating and decommissioning (D and D). These four facilities include two reactor facilities containing spent fuel. One of these reactor facilities also contains 55 tons of sodium with approximately 34 tons containing activated sodium-22, 2.5 tons of lithium hydride, approximately 100 tons of potentially contaminated lead, and several other hazardous materials as well as bulk quantities of contaminated scrap metals. The other two facilities to be transferred include a facility with a bank of hot cells containing high levels of transferable contamination and also a facility containing significant quantities of uranyl nitrate and quantities of transferable contamination. This work plan documents the objectives, technical requirements, and detailed work plans--including preliminary schedules, milestones, and conceptual FY 1996 cost estimates--for the Oak Ridge National Laboratory (ORNL). This plan has been developed by the Environmental Restoration (ER) Program of Lockheed Martin Energy Systems (Energy Systems) for the US Department of Energy (DOE) Oak Ridge Operations Office (ORO).

  17. Annual Report for the OAK Fund, Academic Year 2013-2014 

    E-Print Network [OSTI]

    Herbert, Bruce E.

    2015-02-17

    Annual report (year 1) for the OAK Fund, the funding to support publication fees for open access articles written by Texas A&M faculty....

  18. Thomas Mason Oak Ridge National Lab July 10 2012 SB Summit

    Energy Savers [EERE]

    National Laboratory Presented to the DOENNSA Regional Small Business Summit Thomas E. Mason Director, Oak Ridge National Laboratory Knoxville, Tennessee July 10, 2012 2 Managed...

  19. Observed and modeled ecosystem isoprene fluxes from an oak-dominated...

    Office of Scientific and Technical Information (OSTI)

    isoprene fluxes from an oak-dominated temperate forest and the influence of drought stress Citation Details In-Document Search Title: Observed and modeled ecosystem isoprene...

  20. Geological Hazards Labs Spring 2010

    E-Print Network [OSTI]

    Chen, Po

    Geological Hazards Labs Spring 2010 TA: En-Jui Lee (http://www.gg.uwyo.edu/ggstudent/elee8/site - An Indispensible Tool in Hazard Planning 3 26/1; 27/1 Lab 2: Geologic Maps - Mapping the Hazards 4 2/2; 3/2 Lab 3: Population - People at Risk 5 9/2; 10/2 Lab 4: Plate Tectonics - Locating Geologic Hazards 6 16/2; 17/2 Lab 5