National Library of Energy BETA

Sample records for noted process pad

  1. Notes for Greenbook Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes Notes for Greenbook Process W. Kramer's Flip Charts - Input from the attendees on the Greenbook NUG Meeting February 22-23, 2001 The following are notes transcribed from the flip charts Bill filled in with attendee comments. Topic: The Last Greenbook CONS * 1 Person wrote it * Difficult to extract requirements * Needed to be "more even" tech edited * Latex is not immediately compatible with web-based text * Too complex for non-involved * Target audience not clear PROS * Person

  2. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes Notes ERSUG Meeting Summary Notes, November 15, 1999 Here are some highlights from the discussions (excepting the items contributed by ERSUG Chair, Bas Bramms below): During the state of NERSC presentation by Jim Craw a primary topic of discussion was the issue of the processing capabilities of the PVP cluster. Since the upgrade of the batch system processors to SV1s, some concern has been expressed about the relatively poorer processing capabilities of the J90SE processors on the

  3. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes Notes Why the June 1995 ERSUG Meeting is Important Bill McCurdy describes below a competitive process through which a decision will be made by MICS Division (formerly the OSC) in the June, 1995 timeframe to: (1) possibly move NERSC to Lawrence Berkeley National Laboratory, and (2) redefine to some extent the mission of the Center. All of this would be effected within a significantly reduced cost envelope. The LLNL proposal to keep NERSC where it is and the LBL proposal may soon be

  4. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes Notes Accomodations at Argonne The Argonne contact person for the NUG Meeting is Mike Minkoff of the Mathematics and Computer Science Division. His phone number is (630) 252-7234. Last edited: 2011-04-01 11:41

  5. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes Notes Live Media Streaming via RealPlayer Media streaming of these lectures will be provided via RealPlayer. Users of Windows- or Macintosh-based computers will be able to see and hear the presentation by way of the following procedures. 1. Download and open the slide files onto your computer. 2. Make certain you have the current version of RealPlayer installed. These are available at the Real Free Player Download web site 3. Start the RealPlayer application, and then enter the following

  6. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    PAD District Imports by Country of Origin Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for

  7. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Receipts by Pipeline, Tanker, and Barge Between PAD Districts Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The

  8. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Rail between PAD Districts

  9. Some notes on the application of discrete wavelet transform in image processing

    SciTech Connect (OSTI)

    Caria, Egydio C. S.; Costa A, Trajano A. de; Rebello, Joao Marcos A.

    2011-06-23

    Mathematical transforms are used in signal processing in order to extract what is known as 'hidden' information. One of these mathematical tools is the Discrete Wavelet Transform (DWT), which has been increasingly employed in non-destructive testing and, more specifically, in image processing. The main concern in the present work is to employ DWT to suppress noise without losing relevant image features. However, some aspects must be taken into consideration when applying DWT in image processing, mainly in the case of weld radiographs, in order to achieve consistent results. Three topics were selected as representative of these difficulties, as follows: 1) How can image matrix be filled to fit the 2{sup n} lines and 2{sup n} rows requirement? 2) How can the most suitable decomposition level of the DWT function and the correct choice of their coefficient suppression be selected? 3) Is there any influence of the scanning direction and the weld radiograph image, e.g., longitudinal or transversal, on the final processing image? It is known that some artifacts may be present in weld radiograph images. Indeed, the weld surface is frequently rough and rippled, what can be seen as gray level variation on the radiograph, being sometimes mistaken as defective areas. Depending on the position of these artifacts, longitudinal or transversal to the weld bead, they may have different influences on the image processing procedure. This influence is clearly seen in the distribution of the DWT Function coefficients. In the present work, examples of two weld radiographs of quite different image quality were given in order to exemplify it.

  10. OTS NOTE

    Office of Legacy Management (LM)

    c3 Alexander Williams FROM: Ed Mitchellcm SUBJECT: Babcock and Wilcox Elimination Recommendation The purpose of this note is to provide you with certain inf regarding the ...

  11. OTS NOTE

    Office of Legacy Management (LM)

    941 OTS NOTE DATE: July 2, 1990 TO: W. Alexander Williams FROM : Don Mackenzie d%? SUBJECT: Elimination of 3 Facilities from NSRAP . + 9 Enclosed are elimination recommendations...

  12. Blue Note

    ScienceCinema (OSTI)

    Murray Gibson

    2010-01-08

    Argonne's Murray Gibson is a physicist whose life's work includes finding patterns among atoms. The love of distinguishing patterns also drives Gibson as a musician and Blues enthusiast."Blue" notes are very harmonic notes that are missing from the equal temperament scale.The techniques of piano blues and jazz represent the melding of African and Western music into something totally new and exciting.

  13. Blue Note

    SciTech Connect (OSTI)

    Murray Gibson

    2007-04-27

    Argonne's Murray Gibson is a physicist whose life's work includes finding patterns among atoms. The love of distinguishing patterns also drives Gibson as a musician and Blues enthusiast."Blue" notes are very harmonic notes that are missing from the equal temperament scale.The techniques of piano blues and jazz represent the melding of African and Western music into something totally new and exciting.

  14. Pad polishing for rapid production of large flats

    SciTech Connect (OSTI)

    Berggren, R.R.; Schmell, R.A.

    1997-11-01

    Pad polishing is an efficient technique for polishing-out a ground surface and reaching a figure better than one wave, ready for completion with less than an hour on a planetary polisher. For the 350 mm square piece of BK-7, removal was one micrometer every 10 minutes. Polishing-out from a 5 micrometer grind took less than 3 hours, to a surface smoothness of one nm rms. Other tests verified that the pad leaves no unusual subsurface damage. Following completion on a pitch planetary polisher, surface finish is the same as obtained for conventional processing. Unlike pitch, the pad retains its surface figure, producing a uniform result when used on a production basis. Coupled with the speed of production and low capital cost of overarm machines, it provides a cost-effective approach.

  15. Pad printer for electronics. Final report

    SciTech Connect (OSTI)

    1998-05-01

    This is the Final report on DARPA-sponsored development Program Pad Printer for Electronics DE-FC04-95AL87486 which was initiated in February, 1995 and intended to run 24 months to February 1997. The Program has significant value to the Thick Film processing industry, an electronic manufacturing alternative for producing functional modules integrated at the multichip level. The result is highly reliable, high volumetric efficiency, subassemblies for military applications and for commercial applications in severe environments, such as automotive, portable communications, and bio-implantable devices. The program progressed quite satisfactorily through 19 months, when it encountered severe, non-technical, difficulties. Resolving these difficulties resulted in several months of delay in completing the Program, but resulted in only a trivial increase in total program cost and no increase in cost to the sponsor. The principle Objective of the Program was the development of a printing system -- machine and appropriate inks -- compatible with existing thick-film processing but offering a 5x improvement in line density. This objective has been met. The Pad Printer is capable of printing suitable inks in traces 25 g wide on 50g centers to a fired thickness of 3 {mu}; each of these parameters is roughly 1/5 the value of the current alternative, silk-screen printing. The available inks represent an assortment of conductor, dielectric, and insulator formulations and the knowledge developed permits extending this family of inks to new and diverse functional materials. An important secondary objective was maximum compatibility with existing Thick Film processing; the printer and ink systems may be substituted directly for the silk screen printers in existing processes. The Program reached or exceeded its other Technical Objectives in almost every case and, in those few instances where the objective was only partially met, work continues under private funding.

  16. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    Type, PAD District, and Selected States 224 Energy Information Administration Petroleum Marketing Annual 1997 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  17. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    Type, PAD District, and Selected States 224 Energy Information Administration Petroleum Marketing Annual 1996 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  18. Special Analysis: Naval Reactor Waste Disposal Pad

    SciTech Connect (OSTI)

    Cook, J.R.

    2003-03-31

    This report presents the results of a special study of the Naval Reactor Waste Disposal Pad located within the boundary of the E-Area Low-Level Waste Facility at the Savannah River Site.

  19. Next Generation Non-particulate Dry Nonwoven Pad for Chemical Warfare Agent Decontamination

    SciTech Connect (OSTI)

    Ramkumar, S S; Love, A; Sata, U R; Koester, C J; Smith, W J; Keating, G A; Hobbs, L; Cox, S B; Lagna, W M; Kendall, R J

    2008-05-01

    New, non-particulate decontamination materials promise to reduce both military and civilian casualties by enabling individuals to decontaminate themselves and their equipment within minutes of exposure to chemical warfare agents or other toxic materials. One of the most promising new materials has been developed using a needlepunching nonwoven process to construct a novel and non-particulate composite fabric of multiple layers, including an inner layer of activated carbon fabric, which is well-suited for the decontamination of both personnel and equipment. This paper describes the development of a composite nonwoven pad and compares efficacy test results for this pad with results from testing other decontamination systems. The efficacy of the dry nonwoven fabric pad was demonstrated specifically for decontamination of the chemical warfare blister agent bis(2-chloroethyl)sulfide (H or sulfur mustard). GC/MS results indicate that the composite fabric was capable of significantly reducing the vapor hazard from mustard liquid absorbed into the nonwoven dry fabric pad. The mustard adsorption efficiency of the nonwoven pad was significantly higher than particulate activated carbon (p=0.041) and was similar to the currently fielded US military M291 kit (p=0.952). The nonwoven pad has several advantages over other materials, especially its non-particulate, yet flexible, construction. This composite fabric was also shown to be chemically compatible with potential toxic and hazardous liquids, which span a range of hydrophilic and hydrophobic chemicals, including a concentrated acid, an organic solvent and a mild oxidant, bleach.

  20. FC-PAD Organization and Activities | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    FC-PAD Organization and Activities FC-PAD Organization and Activities This document provides an in-depth description of the organization of the Fuel Cell Consortium for Performance and Durability (FC-PAD), including its scientific activities and six different thrust areas. FC-PAD Organization and Activities (4.08 MB) More Documents & Publications FCTO Consortia Overview (HyMARC and FC-PAD) Webinar FCTO Consortia Overview (HyMARC and FC-PAD) Webinar DOE Fuel Cell Pre-Solicitation Workshop -

  1. Verde iPad app | Open Energy Information

    Open Energy Info (EERE)

    iPad app An energy audit tool for the iPad the recommends the best places to upgrade to energy star products, as well as how much money and carbon you will save by doing so....

  2. Calibration Pad Assignments for Spectral Gamma (November 1985) | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Pad Assignments for Spectral Gamma (November 1985) Calibration Pad Assignments for Spectral Gamma (November 1985) Calibration Pad Assignments for Spectral Gamma (November 1985) Calibration Pad Assignments for Spectral Gamma (November 1985) (5.3 MB) More Documents & Publications Parameter Assignments for Spectral Gamma-Ray Borehole Calibration Models (April 1984) Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and Potassium (October 2013) Grade

  3. Research Notes and Information References

    Energy Science and Technology Software Center (OSTI)

    1994-12-01

    The RNS (Research Notes System) is a set of programs and databases designed to aid the research worker in gathering, maintaining, and using notes taken from the literature. The sources for the notes can be books, journal articles, reports, private conversations, conference papers, audiovisuals, etc. The system ties the databases together in a relational structure, thus eliminating data redundancy while providing full access to all the information. The programs provide the means for access andmore » data entry in a way that reduces the key-entry burden for the user. Each note has several data fields. Included are the text of the note, the subject classification (for retrieval), and the reference identification data. These data are divided into four databases: Document data - title, author, publisher, etc., fields to identify the article within the document; Note data - text and page of the note; Sublect data - subject categories to ensure uniform spelling for searches. Additionally, there are subsidiary files used by the system, including database index and temporary work files. The system provides multiple access routes to the notes, both structurally (access method) and topically (through cross-indexing). Output may be directed to a printer or saved as a file for input to word processing software.« less

  4. L-connect routing of die surface pads to the die edge for stacking in a 3D array

    DOE Patents [OSTI]

    Petersen, Robert W.

    2000-01-01

    Integrated circuit chips and method of routing the interface pads from the face of the chip or die to one or more sidewall surfaces of the die. The interconnection is routed from the face of the die to one or more edges of the die, then routed over the edge of the die and onto the side surface. A new pad is then formed on the sidewall surface, which allows multiple die or chips to be stacked in a three-dimensional array, while enabling follow-on signal routing from the sidewall pads. The routing of the interconnects and formation of the sidewall pads can be carried out in an L-connect or L-shaped routing configuration, using a metalization process such as laser pantography.

  5. Notes for Visualization Requirememnts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes for Vis Requirements Notes for Visualization Requirememnts Notes from June 5, 2002, Visualization Requirements for DOE-Sponsored Computational Science and Engineering Applications A DOE Workshop to Be Held 
at Lawrence Berkeley National Laboratory,
Berkeley, California, June 5, 2002 Workshop Co-organizers: Bernd Hamann 
University of California-Davis Lawrence Berkeley National Lab. E. Wes Bethel 
Lawrence Berkeley National Lab. Horst D. Simon
Lawrence Berkeley National Lab.

  6. Meeting Summary Notes

    Office of Environmental Management (EM)

    records check list: Information that should be requested by SOMD of receiving facility Medical records: Problem list: list of all past and current medical diagnosis and surgical procedures. Medication list Physical exam notes Lab and diagnostic testing results Pertinent HRP notes. (temporary removals, medical and psychological issues) Psychiatric records: A summary or actual note of the psychiatric or psychological evaluation

    Medical Records Checklist - September 14, 2010 Medical Records

  7. Calculation note review

    SciTech Connect (OSTI)

    Ramble, A.L.

    1996-09-30

    This document contains a review of the calculation notes which were prepared for the Tank Waste Remediation System Basis for Interim Operation.

  8. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    Type, PAD District, and Selected States Energy Information Administration Petroleum Marketing Annual 1996 233 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  9. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    Type, PAD District, and Selected States Energy Information Administration Petroleum Marketing Annual 1997 233 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  10. Notes and Action Items

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes and Action Items Notes and Action Items Report on the NUGEX business meeting of June 6, 2000, in Oak Ridge Minute notes by Bas Braams First of all, many thanks to the organizers of the preceding NUG meeting: Roberta Boucher, David Dean, Brian Hingerty, Bill Kramer, Donald Spong and Malcolm Stocks. Likewise thanks to Brian Hingerty and Mike Minkoff for organizing the Users Helping Users events, and to Tom DeBoni, Osni Marques, Jeffrey Squyres and David Turner for the NERSC training classes.

  11. Meeting Notes and Presentations

    Office of Environmental Management (EM)

    Corporate Board Notes and Slides Notes from EM Corporate QA Board Tele-Conference - February 22, 2010 1 of 2 General: Attendance of voting board members was documented. All members were present or had a representative present on the call. Previous 5 Focus Areas: Dave Tuttel presented the proposed closeout of the previous 5 focus areas for the EM Corporate Board. * Focus Area 1 (Requirements Flow Down) - Board voted to close the focus area (unanimous) * Focus Area 2 (Adequate NQA-1 Suppliers) -

  12. Table 4. Estimation Results for PAD District Regions

    U.S. Energy Information Administration (EIA) Indexed Site

    Estimation Results for PAD District Regions Dependent Variable: D(RETPAD1) Dependent Variable: D(RETPAD2) Dependent Variable: D(RETPAD3) Dependent Variable: D(RETPAD4) Dependent...

  13. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    78.5 48.8 See footnotes at end of table. 182 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  14. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    76.6 45.7 See footnotes at end of table. 182 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  15. Prices by Sales Type, PAD District, and Selected States

    U.S. Energy Information Administration (EIA) Indexed Site

    52.1 See footnotes at end of table. 224 Energy Information Administration Petroleum Marketing Annual 1995 Table 39. No. 2 Distillate a Prices by Sales Type, PAD District, and...

  16. SEP Success Story: "Green Launching Pad" Supports Clean Energy...

    Broader source: Energy.gov (indexed) [DOE]

    John Lynch, and UNH President Mark Huddleston held at EnerTrac, Inc., in Hudson, NH. | Courtesy of University of New Hampshire Photographic Services Green Launching Pad 2.0 awards ...

  17. Notes and Action Items

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Notes and Action Items Notes and Action Items ERSUG Action Items from June 1996 meeting at Germantown, MD Get DOE staff on mailers for broadcast of ERSUG issues Responsibility: Kendall and Kitchens Review and comment on ERSUG Proposal to SAC Responsibility: All of ERSUG Comments to Rick Kendall by July 17th email: ra_kendall@pnl.gov Fax : (509) 375-6631 Review and comment on Requirements Document "Greenbook" Responsibility: All of ERSUG Comments to Rick Kendall by August 7th email:

  18. VOL2NOTE.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    B Explanatory Notes The following Explanatory Notes are provided to assist in understanding and interpreting the data presented in this publication. * Note 1. Petroleum Supply Reporting System * Note 2. Monthly Petroleum Supply Reporting System * Note 3. Technical Notes for Detailed Statistics Tables * Note 4. Domestic Crude Oil Production * Note 5. Export Data * Note 6. Quality Control and Data Revision * Note 7. Frames Maintenance * Note 8. Descriptive Monthly Statistics * Note 9. Practical

  19. Template:Note | Open Energy Information

    Open Energy Info (EERE)

    search Note Note: Usage Method 1 The following displays the note icon and the word 'Note:'. You can follow this with whatever textimagesmarkup you like, and it works...

  20. Exposure-rate calibration using large-area calibration pads

    SciTech Connect (OSTI)

    Novak, E.F.

    1988-09-01

    The US Department of Energy (DOE) Office of Remedial Action and Waste Technology established the Technical Measurements Center (TMC) at the DOE Grand Junction Projects Office (GJPO) in Grand Junction, Colorado, to standardize, calibrate, and compare measurements made in support of DOE remedial action programs. A set of large-area, radioelement-enriched concrete pads was constructed by the DOE in 1978 at the Walker Field Airport in Grand Junction for use as calibration standards for airborne gamma-ray spectrometer systems. The use of these pads was investigated by the TMC as potential calibration standards for portable scintillometers employed in measuring gamma-ray exposure rates at Uranium Mill Tailings Remedial Action (UMTRA) project sites. Data acquired on the pads using a pressurized ionization chamber (PIC) and three scintillometers are presented as an illustration of an instrumental calibration. Conclusions and recommended calibration procedures are discussed, based on the results of these data.

  1. Notes and Definitions

    Weekly Natural Gas Storage Report (EIA)

    Notes and Definitions This report tracks U.S. natural gas inventories held in underground storage facilities. The weekly stocks generally are the volumes of working gas as of the report date. The "net change" in reported stock levels reflects all events affecting working gas in storage, including injections, withdrawals, and reclassifications between base and working gas. The "implied flow" estimate represents movements of working natural gas into or out of underground

  2. V-141: HP ElitePad 900 Secure Boot Bug Lets Local Users Boot...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1: HP ElitePad 900 Secure Boot Bug Lets Local Users Boot to Other Operating Systems V-141: HP ElitePad 900 Secure Boot Bug Lets Local Users Boot to Other Operating Systems April...

  3. FCTO Consortia Overview (HyMARC and FC-PAD) Webinar | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Consortia Overview (HyMARC and FC-PAD) Webinar FCTO Consortia Overview (HyMARC and FC-PAD) Webinar Access the recording and download the presentation slides from the Fuel Cell Technologies Office webinar "FCTO Consortia Overview (HyMARC and FC-PAD)" held on January 7, 2016. FCTO Consortia Overview (HyMARC and FC-PAD) Webinar Slides (7.43 MB) More Documents & Publications FC-PAD Organization and Activities Hydrogen Storage Lab PI Workshop: HyMARC and NREL-Led Characterization Effort

  4. PIC Transcribed Flip Chart Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    "Workshop" versus "meeting" Could provide someone to take verbal comments Page 5 PIC Transcribed Flip Chart Notes Wednesday, October 31, 2012 300 Area Public Involvement...

  5. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Products Supplied Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels per

  6. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Exports Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels per short ton.

  7. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Exports by Destination Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels

  8. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Area of Entry Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels per short

  9. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    U.S. Imports by Country of Origin Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is

  10. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Imports by Destination Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels

  11. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Pipeline, Tanker, and Barge Between PADDs Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for

  12. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Tanker and Barge Between PADDs Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5

  13. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Shell Storage Capacity at Operable Refineries Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for

  14. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Working Storage Capacity at Operable Refineries Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor

  15. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Yield Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels per short ton.

  16. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Production Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels per short

  17. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    & Blender Net Production Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5

  18. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Refinery Stocks Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels per

  19. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Supply and Disposition Balance Definitions Key Terms Definition Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5

  20. Table 42. Residual Fuel Oil Prices by PAD District and State

    Gasoline and Diesel Fuel Update (EIA)

    Information Administration Petroleum Marketing Annual 1995 245 Table 42. Residual Fuel Oil Prices by PAD District and State (Cents per Gallon Excluding Taxes) - Continued...

  1. Table 42. Residual Fuel Oil Prices by PAD District and State

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Information AdministrationPetroleum Marketing Annual 1998 203 Table 42. Residual Fuel Oil Prices by PAD District and State (Cents per Gallon Excluding Taxes) - Continued...

  2. "Green Launching Pad" Supports Clean Energy Small Businesses | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy "Green Launching Pad" Supports Clean Energy Small Businesses "Green Launching Pad" Supports Clean Energy Small Businesses May 24, 2012 - 2:01pm Addthis Green Launching Pad 2.0 awards ceremony with Secretary Chu, Gov. John Lynch, and UNH President Mark Huddleston held at EnerTrac, Inc., in Hudson, NH. | Courtesy of University of New Hampshire Photographic Services Green Launching Pad 2.0 awards ceremony with Secretary Chu, Gov. John Lynch, and UNH President Mark

  3. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information Administration Petroleum Marketing Annual 1995 Table A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District and State, 1984-Present (Cents per Gallon...

  4. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    table. 56 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  5. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    table. 56 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  6. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    U.S. Energy Information Administration (EIA) Indexed Site

    AdministrationPetroleum Marketing Annual 1999 401 Table A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District and State, 1984-Present (Cents per Gallon...

  7. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    table. 56 Energy Information Administration Petroleum Marketing Annual 1995 Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  8. OpenEI Community - notes

    Open Energy Info (EERE)

    more

    http:en.openei.orgcommunityblognotes-callcomments notes Linked Open Data Workshop in Washington, D.C. Fri, 28 Sep 2012 00:57:30 +0000 Jweers 521 at...

  9. GETEM Manuals and Revision Notes

    Broader source: Energy.gov [DOE]

    Please refer to these manuals and revision notes prior to downloading and running the Geothermal Electricity Technology Evaluation Model (GETEM). Because this is a beta version, you are urged to...

  10. Thermal Neutron Detectors with Discrete Anode Pad Readout

    SciTech Connect (OSTI)

    Yu,B.; Schaknowski, N.A., Smith, G.C., DeGeronimo, G., Vernon, E.O.

    2008-10-19

    A new two-dimensional thermal neutron detector concept that is capable of very high rates is being developed. It is based on neutron conversion in {sup 3}He in an ionization chamber (unity gas gain) that uses only a cathode and anode plane; there is no additional electrode such as a Frisch grid. The cathode is simply the entrance window, and the anode plane is composed of discrete pads, each with their own readout electronics implemented via application specific integrated circuits. The aim is to provide a new generation of detectors with key characteristics that are superior to existing techniques, such as higher count rate capability, better stability, lower sensitivity to background radiation, and more flexible geometries. Such capabilities will improve the performance of neutron scattering instruments at major neutron user facilities. In this paper, we report on progress with the development of a prototype device that has 48 x 48 anode pads and a sensitive area of 24cm x 24cm.

  11. EIA-906 & EIA-920, and EIA-923 Database Notes

    U.S. Energy Information Administration (EIA) Indexed Site

    EIA-906 & EIA-920, and EIA-923 Database Notes" ,"Date","Subject","Notes" ,38086,"Excel File Documentation","The documentation included with the Excel file has been updated to include the year to date columns at the end (far right) of the file. In addition, the documentation now clearly notes that the total consumption numbers include fuel consumed at combined heat and power plants for the purpose of producing process steam."

  12. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    these lectures will be provided via RealPlayer. Users of Windows- or Macintosh-based computers will be able to see and hear the presentation by way of the following procedures. 1....

  13. Topic A Note: Includes STEPS Subtopic

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Topic A Note: Includes STEPS Subtopic 33 Total Projects Developing and Enhancing Workforce Training Programs

  14. Historical Material Analysis of DC745U Pressure Pads

    SciTech Connect (OSTI)

    Ortiz-Acosta, Denisse

    2012-07-30

    As part of the Enhance Surveillance mission, it is the goal to provide suitable lifetime assessment of stockpile materials. This report is an accumulation of historical publication on the DC745U material and their findings. It is the intention that the B61 LEP program uses this collection of data to further develop their understanding and potential areas of study. DC745U is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and methyl-vinyl siloxane repeat units. Originally, this material was manufactured by Dow Corning as Silastic{reg_sign} DC745U at their manufacturing facility in Kendallville, IN. Recently, Dow Corning shifted this material to the Xiameter{reg_sign} brand product line. Currently, DC745U is available through Xiameter{reg_sign} or Dow Corning's distributor R. D. Abbott Company. DC745U is cured using 0.5 wt% vinyl-specific peroxide curing agent known as Luperox 101 or Varox DBPH-50. This silicone elastomer is used in numerous parts, including two major components (outer pressure pads and aft cap support) in the W80 and as pressure pads on the B61. DC745U is a proprietary formulation, thus Dow Corning provides limited information on its composition and properties. Based on past experience with Dow Corning, DC745U is at risk of formulation changes without notification to the costumer. A formulation change for DC745U may have a significant impact because the network structure is a key variable in determining material properties. The purpose of this report is to provide an overview of historical DC745U studies and identify gaps that need to be addressed in future work. Some of the previous studies include the following: 1. Spectroscopic characterization of raw gum stock. 2. Spectroscopic, thermal, and mechanical studies on cured DC745U. 3. Nuclear Magnetic Resonance (NMR) and solvent swelling studies on DC745U with different crosslink densities. 4. NMR, solvent swelling, thermal, and mechanical studies on thermally aged

  15. SEP Success Story: Green Launching Pad Taps Six More Companies for Take-off

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy Green Launching Pad Taps Six More Companies for Take-off SEP Success Story: Green Launching Pad Taps Six More Companies for Take-off April 29, 2011 - 9:58am Addthis Yesterday, U.S. Secretary of Energy Steven Chu joined New Hampshire Governor John Lynch and University of New Hampshire (UNH) President Mark W. Huddleston in announcing the six businesses selected to participate in the second round of the Green Launching Pad. Learn more. Addthis Related Articles Green

  16. Construction and characterization of the TL/TH thorium calibration pads

    SciTech Connect (OSTI)

    Steele, W.D.

    1987-09-01

    The Technical Measurements Center (TMC) was established and was tasked with developing and/or recommending measurement methods for use in support of remedial action programs. Since one aspect of this technical support is the provision of calibration facilities for standardization of field measurements, four sets of thorium-232 enriched pads (two pads per set) were constructed for use by remedial action contractors in calibrating portable field instruments that are used to make direct, in-situ measurements of radium-226, thorium-232, and potassium-40. This report presents the design, construction, and characterization data of the eight calibration pads. 17 refs., 8 figs., 15 tabs.

  17. FC-PAD: Fuel Cell Consortium for Performance and Durability | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy FC-PAD: Fuel Cell Consortium for Performance and Durability FC-PAD: Fuel Cell Consortium for Performance and Durability Illustration of the research consortia model showing a 'National Laboratory Core Team' as the central role with three sub-groups of University & Non-Profit, Industry, and National Lab contributing to the core. The Fuel Cell Consortium for Performance and Durability (FC-PAD) will aid in the understanding of-and lead to significant improvements in-fuel cell

  18. Webinar January 7: FCTO Consortia Overview Webinar (FC-PAD and HyMARC) |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy January 7: FCTO Consortia Overview Webinar (FC-PAD and HyMARC) Webinar January 7: FCTO Consortia Overview Webinar (FC-PAD and HyMARC) January 5, 2016 - 1:39pm Addthis The Fuel Cell Technologies Office will present a live webinar titled "FCTO Consortia Overview Webinar (FC-PAD and HyMARC)" on Thursday, January 7, from 2 to 3 p.m. Eastern Standard Time (EST). To accelerate the rate of progress in developing technologies to improve the performance and durability

  19. Refinery Capacity Report - Explanatory Notes

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Information Administration/Refinery Capacity Report 1 Explanatory Notes Survey Methodology Description of Survey Form The Form EIA-820, "Annual Refinery Report," is the primary source of data in the "Refinery Capacity Report" tables. The form collects data on the consumption of purchased steam, electricity, coal, and natural gas; refinery receipts of crude oil by method of transportation; operable capacity for atmospheric crude oil distillation units and downstream

  20. Radiological Survey Tool Set for ArcGIS 8.3 and ArcPad 6.0

    SciTech Connect (OSTI)

    ROGER, COTTRELL

    2004-11-30

    The Radiological Control Operations (RCO) group at the Savannah River Site (SRS) is tasked with conducting routine surveys for the detection of radiological contaminants in the environment. The Radiological Survey Tool Set (RSTS) was developed by the Environmental & Geographic Information Systems (EGIS) group of SRS to assist RCO personnel in this survey process. The tool set consists of two major components. The first component is a custom extension for ArcGIS 8.3 that allows the user to interactively create a sampling plan prior to entering the field. Additionally, the extension allows the user to upload field-collected data to the GIS with post-processing functionality. The second component is a custom ArcPad 6.0 applet. This applet provides the user with navigational capabilities to a selected origin point with the help of Global Positioning Systems (GPS) technology, and the recording of the sample data results into a hand-held field computer via ArcPad 6.0 software.

  1. Table 3. Estimation Results for National and Sub-PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    Estimation Results for National and Sub-PAD District Regions Dependent Variable: D(RETUS) Dependent Variable: D(RETPAD1X) Dependent Variable: D(RETPAD1Y) Dependent Variable:...

  2. Webinar: FCTO Consortia Overview Webinar (FC-PAD and HyMARC)

    Broader source: Energy.gov [DOE]

    The Fuel Cell Technologies Office will present a live webinar titled “FCTO Consortia Overview Webinar (FC-PAD and HyMARC)” on Thursday, January 7, from 2 to 3 p.m. EST.

  3. Table 42. Residual Fuel Oil Prices by PAD District and State

    Gasoline and Diesel Fuel Update (EIA)

    55.1 47.1 W W 55.1 46.2 See footnotes at end of table. 42. Residual Fuel Oil Prices by PAD District and State Energy Information Administration Petroleum...

  4. Table 42. Residual Fuel Oil Prices by PAD District and State

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    45.5 49.2 W W 44.5 45.4 See footnotes at end of table. 42. Residual Fuel Oil Prices by PAD District and State Energy Information Administration Petroleum...

  5. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    62.4 65.5 51.3 See footnotes at end of table. Energy Information AdministrationPetroleum Marketing Annual 1999 191 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  6. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    64.6 54.0 See footnotes at end of table. Energy Information Administration Petroleum Marketing Annual 1995 233 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  7. Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    60.4 60.0 45.2 See footnotes at end of table. Energy Information AdministrationPetroleum Marketing Annual 1998 191 Table 40. No. 2 Diesel Fuel Prices by Sales Type, PAD District,...

  8. SEP Success Story: "Green Launching Pad" Supports Clean Energy Small Businesses

    Broader source: Energy.gov [DOE]

    A commercialization partnership funded by the State Energy Program – known as the Green Launching Pad program -- is a joint effort by the New Hampshire Office of Energy and Planning and the University of New Hampshire. Learn more.

  9. Lecture notes for criticality safety

    SciTech Connect (OSTI)

    Fullwood, R.

    1992-03-01

    These lecture notes for criticality safety are prepared for the training of Department of Energy supervisory, project management, and administrative staff. Technical training and basic mathematics are assumed. The notes are designed for a two-day course, taught by two lecturers. Video tapes may be used at the options of the instructors. The notes provide all the materials that are necessary but outside reading will assist in the fullest understanding. The course begins with a nuclear physics overview. The reader is led from the macroscopic world into the microscopic world of atoms and the elementary particles that constitute atoms. The particles, their masses and sizes and properties associated with radioactive decay and fission are introduced along with Einstein's mass-energy equivalence. Radioactive decay, nuclear reactions, radiation penetration, shielding and health-effects are discussed to understand protection in case of a criticality accident. Fission, the fission products, particles and energy released are presented to appreciate the dangers of criticality. Nuclear cross sections are introduced to understand the effectiveness of slow neutrons to produce fission. Chain reactors are presented as an economy; effective use of the neutrons from fission leads to more fission resulting in a power reactor or a criticality excursion. The six-factor formula is presented for managing the neutron budget. This leads to concepts of material and geometric buckling which are used in simple calculations to assure safety from criticality. Experimental measurements and computer code calculations of criticality are discussed. To emphasize the reality, historical criticality accidents are presented in a table with major ones discussed to provide lessons-learned. Finally, standards, NRC guides and regulations, and DOE orders relating to criticality protection are presented.

  10. AIRMaster+ Release Notes | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AIRMaster+ (Version 1.2.7) Release Notes Release Notes (Version 1.2.7) (296.45 KB) More Documents & Publications AIRMaster+ Software Tool Brochure AIRMaster+ User Manual AIRMaster+ ...

  11. Manhattan Project: A Note on Sources

    Office of Scientific and Technical Information (OSTI)

    A NOTE ON SOURCES Resources > Note on Sources The text for this web site is a combination of original material and adaptations from previous publications of the Department of ...

  12. Manhattan Project: A Note on Sources

    Office of Scientific and Technical Information (OSTI)

    A NOTE ON SOURCES Resources > Note on Sources The text for this web site is a combination ... To the best of our knowledge, all text and images on this web site are in the public ...

  13. Meeting Summary Notes | Department of Energy

    Office of Environmental Management (EM)

    Department of Energy Notes re NOI for Convention on Supplementary Compensation Meeting Notes re NOI for Convention on Supplementary Compensation notes from meeting on Convention on Supplementary Compensation Meeting Notes re NOI for Convention on Supplementary Compensation (45.83 KB) More Documents & Publications Convention on Supplementary Compensation for Nuclear Damage Contingent Cost Allocation Public comment re Convention on Supplementary Compensation on Nuclear Damage Contingent

  14. EM QA Working Group September 2011 Notes

    Broader source: Energy.gov [DOE]

    Meeting minutes and notes from the EM QA Working Group video conference meeting held in September 2011.

  15. Engineering evaluation/cost analysis for the proposed removal of contaminated materials from pad 1 at the Elza Gate site, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Not Available

    1990-09-01

    This engineering evaluation/cost analysis (EE/CA) has been prepared in support of the proposed removal action for cleanup of radioactively contaminated concrete and soil beneath a building on privately owned commercial property in Oak Ridge, Tennessee. The property, known as the Elza Gate site, became contaminated with uranium-238, radium-226, thorium-232, thorium-230, and decay products as a result of the Manhattan Engineer District storing uranium ore and ore processing residues at the site in the early 1940s. The US Department of Energy (DOE) has responsibility for cleanup of the property under its Formerly Utilized Sites Remedial Action Program (FUSRAP). The DOE plans to remove the cracked and worn concrete pad and contaminated subsoil beneath the pad, after which the property owner/tenant will provide clean backfill and new concrete. Portions of the pad and subsoil are contaminated and, if stored or disposed of improperly, may represent a potential threat to public health or welfare and the environment. The EE/CA report is the appropriate documentation for the proposed removal action, as identified in guidance from the US Environmental Protection Agency. The objective of the EE/CA report, in addition to identifying the planned removal action, is to document the selection of response activities that will mitigate the potential for release of contaminants from the property into the environment and minimize the related threats to public health or welfare and the environment. 7 refs., 2 figs., 3 tabs.

  16. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Residual Fuel Imports by State Definitions Key Terms Definition Barrel A unit of volume equal to 42 U.S. gallons. Imports Receipts of crude oil and petroleum products into the 50 States and the District of Columbia from foreign countries, Puerto Rico, the Virgin Islands, and other U.S. possessions and territories. Petroleum Administration for Defense (PAD) Districts Geographic aggregations of the 50 States and the District of Columbia into five districts by the Petroleum Administration for

  17. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Natural Gas Used as Feedstock for Hydrogen Production Definitions Key Terms Definition Hydrogen The lightest of all gases, occurring chiefly in combination with oxygen in water; exists also in acids, bases, alcohols, petroleum, and other hydrocarbons. Natural Gas A gaseous mixture of hydrocarbon compounds, the primary one being methane. Petroleum Administration for Defense (PAD) Districts Geographic aggregations of the 50 States and the District of Columbia into five districts by the Petroleum

  18. Property:ExplorationNotes | Open Energy Information

    Open Energy Info (EERE)

    the property "ExplorationNotes" Showing 1 page using this property. R RAPIDOverviewGeothermalExplorationCalifornia + The Geothermal Resources Prospecting Permit (PRC...

  19. EM QA Working Group September 2011 Notes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    suspectcounterfeit items, software QA, and corrective actions? Bob also noted that we need to be diligent in the understanding and use of the metrics to avoid potential issues ...

  20. Construction and characterization of the RH/RL radium calibration pads

    SciTech Connect (OSTI)

    Steele, W.D.; Marutzky, S.J.; Dickerson, J.W.

    1989-01-01

    The US Department of Energy (DOE) Office of Remedial Action and Waste Technology has as one of its goals the standardization of field measurements made by its remedial action contractors throughout the country. In support of this goal, the Technical Measurements Center (TMC) was established at the DOE Grand Junction Projects Office (GJPO) Facility, and was tasked with developing and/or recommending measurement methods for use in support of remedial action programs. One aspect of this technical support is the provision of calibration facilities for standardization of field measurements. The report presents the results of the design, construction, and characterization of 14 calibration pads enriched in radium-226. The 14 pads comprise 7 sets with a high and low activity pad in each set. The pads are concrete cylinders, approximately 5 feet in diameter by 2 feet in height. They are intended for use in calibrating portable field instruments that are used by remedial action contractors to make direct, in situ measurements of radium-226, thorium-232, and potassium-40. 23 refs., 6 figs., 14 tabs.

  1. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    82.4 77.1 68.9 62.6 71.6 92.3 89.9 82.6 72.7 - 78.2 See footnotes at end of table. 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State 56 Energy Information...

  2. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    U.S. Energy Information Administration (EIA) Indexed Site

    71.6 92.3 78.2 101.8 83.6 87.5 74.7 See footnotes at end of table. A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District, and State, 1984-Present 452 Energy Information...

  3. Table 31. Motor Gasoline Prices by Grade, Sales Type, PAD District...

    U.S. Energy Information Administration (EIA) Indexed Site

    82.5 75.1 68.6 62.0 70.7 92.7 90.7 81.5 72.8 - 78.0 See footnotes at end of table. 31. Motor Gasoline Prices by Grade, Sales Type, PAD District, and State 56 Energy Information...

  4. Net Movements of Crude Oil and Petroleum Products by Pipeline, Tanker, Barge, and Rail Between PAD Districts, January 2014

    U.S. Energy Information Administration (EIA) Indexed Site

    January 2014 (Thousand Barrels) Commodity PAD District 1 PAD District 2 PAD District 3 Receipts Shipments Net Receipts Receipts Shipments Net Receipts Receipts Shipments Net Receipts Crude Oil 1 ................................................................ 11,209 1,213 9,996 35,554 35,363 190 23,680 28,598 -4,918 Petroleum Products 2 .............................................. 106,990 8,669 107,347 29,831 18,055 -6,599 16,594 124,991 -103,885 Pentanes Plus

  5. PIA - Savannah River Operations Office Lotus Domino/Notes System...

    Broader source: Energy.gov (indexed) [DOE]

    Lotus DominoNotes System PDF icon PIA - Savannah River Operations Office Lotus DominoNotes System More Documents & Publications PIA - DOE Savannah River Operations Office PRISM ...

  6. Note: On the wavelength dependence of the intensity calibration...

    Office of Scientific and Technical Information (OSTI)

    Note: On the wavelength dependence of the intensity calibration factor of extreme ... Title: Note: On the wavelength dependence of the intensity calibration factor of extreme ...

  7. Notes on Newton-Krylov based Incompressible Flow Projection Solver...

    Office of Scientific and Technical Information (OSTI)

    Notes on Newton-Krylov based Incompressible Flow Projection Solver Citation Details In-Document Search Title: Notes on Newton-Krylov based Incompressible Flow Projection Solver The ...

  8. Notes on Newton-Krylov based Incompressible Flow Projection Solver...

    Office of Scientific and Technical Information (OSTI)

    Notes on Newton-Krylov based Incompressible Flow Projection Solver Citation Details In-Document Search Title: Notes on Newton-Krylov based Incompressible Flow Projection Solver ...

  9. Note: Coherent resonances observed in the dissociative electron...

    Office of Scientific and Technical Information (OSTI)

    Note: Coherent resonances observed in the dissociative electron attachment to carbon monoxide Citation Details In-Document Search Title: Note: Coherent resonances observed in the ...

  10. Xyce parallel electronic simulator release notes.

    SciTech Connect (OSTI)

    Keiter, Eric Richard; Hoekstra, Robert John; Mei, Ting; Russo, Thomas V.; Schiek, Richard Louis; Thornquist, Heidi K.; Rankin, Eric Lamont; Coffey, Todd Stirling; Pawlowski, Roger Patrick; Santarelli, Keith R.

    2010-05-01

    The Xyce Parallel Electronic Simulator has been written to support, in a rigorous manner, the simulation needs of the Sandia National Laboratories electrical designers. Specific requirements include, among others, the ability to solve extremely large circuit problems by supporting large-scale parallel computing platforms, improved numerical performance and object-oriented code design and implementation. The Xyce release notes describe: Hardware and software requirements New features and enhancements Any defects fixed since the last release Current known defects and defect workarounds For up-to-date information not available at the time these notes were produced, please visit the Xyce web page at http://www.cs.sandia.gov/xyce.

  11. RAP Meeting Transcribed Flip Chart Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Flip Chart Notes February 15, 2012 Site-wide Permit Workshop May 3 1. Have "post-workshop" session to discuss HAB next steps 2. Recommend Ecology sponsors & facilitates Workshop - Ecology captures notes, but HAB members track issues of concern, too. 3. Web-ex for public when it fits 4. Pre-workshop meeting with HAB issue leaders (potential speakers) Page 1 300 Area HAB next steps... IM & Pam 1. Issue managers meet to review potential issues for HAB/committees 2. Bring back to

  12. Application Note: Power Grid Modeling With Xyce.

    SciTech Connect (OSTI)

    Sholander, Peter E.

    2015-06-01

    This application note describes how to model steady-state power flows and transient events in electric power grids with the SPICE-compatible Xyce TM Parallel Electronic Simulator developed at Sandia National Labs. This application notes provides a brief tutorial on the basic devices (branches, bus shunts, transformers and generators) found in power grids. The focus is on the features supported and assumptions made by the Xyce models for power grid elements. It then provides a detailed explanation, including working Xyce netlists, for simulating some simple power grid examples such as the IEEE 14-bus test case.

  13. Crude Oil Movements of Crude of by Rail between PAD Districts

    U.S. Energy Information Administration (EIA) Indexed Site

    Product: Crude Oil Fuel Ethanol Biodiesel Period-Unit: Monthly-Thousand Barrels Annual-Thousand Barrels Download Series History Download Series History Definitions, Sources & Notes ...

  14. Notes on beam dynamics in linear accelerators

    SciTech Connect (OSTI)

    Gluckstern, R.L.

    1980-09-01

    A collection of notes, on various aspects of beam dynamics in linear accelerators, which were produced by the author during five years (1975 to 1980) of consultation for the LASL Accelerator Technology (AT) Division and Medium-Energy Physics (MP) Division is presented.

  15. LLW notes. Volume 11, No.8

    SciTech Connect (OSTI)

    1996-12-01

    `LLW Notes` is distributed by Afton Associates, Inc. to Low-Level Radioactive Waste Forum Participants and other state, and compact officials identified by those Participants to receive `LLW Notes`. The Low-Level Radioactive Waste Forum (LLW Forum) is an association of state and compact representatives, appointed by governors and compact commissions, established to facilitate state and compact implementation of the Low-Level Radioactive Waste Policy Act of 1980 and the Low-Level Radioactive Waste Policy Amendments Act of 1985 and to promote the objectives of low-level radioactive waste regional compacts. The LLW Forum provides an opportunity for state and compact officials to share information with one another and to exchange views with officials of federal agencies and other interested parties.

  16. LLW notes, Vol. 11, No. 2

    SciTech Connect (OSTI)

    1996-03-01

    `LLW Notes` is distributed by Afton Associates, Inc. to Low-Level Radioactive Waste Forum Participants and other state, and compact officials identified by those Participants to receive LLW Notes. The Low-Level Radioactive Waste Forum (LLW Forum) is an association of state and compact representatives, appointed by governors and compact commissions, established to facilitate state and compact implementation of the Low-Level Radioactive Waste Policy Act of 1980 and the Low-Level Radioactive Waste Policy amendments Act of 1985 and to promote the objectives of low-level radioactive waste regional compacts. The LLW Forum provides an opportunity for state and compact officials to share information with one another and to exchange views with officials of federal agencies and other interested parties.

  17. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Shale Gas Production Definitions Key Terms Definition Shale Gas Natural gas produced from organic (black) shale formations. For definitions of related energy terms, refer to the EIA Energy Glossary. Sources Energy Information Administration, Office of Oil and Gas Explanatory Notes Shale Gas production data collected in conjunction with proved reserves data on Form EIA-23 are unofficial. Official Shale Gas production data from Form EIA-895 can be found in Natural Gas Gross Withdrawals and

  18. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Other Products Definitions Key Terms Definition Aviation Gasoline A complex mixture of relatively volatile hydrocarbons with or without small quantities of additives, blended to form a fuel suitable for use in aviation reciprocating engines. Fuel specifications are provided in ASTM Specification D 910 and Military Specification MIL-G-5572. Note: Data on blending components are not counted in data on finished aviation gasoline. Gas Plant Operator Any firm, including a gas plant owner, which

  19. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Petroleum Product Prices by Sales Type Definitions Key Terms Definition Aviation Gasoline (Finished) A complex mixture of relatively volatile hydrocarbons with or without small quantities of additives, blended to form a fuel suitable for use in aviation reciprocating engines. Fuel specifications are provided in ASTM Specification D 910 and Military Specification MIL-G-5572. Note: Data on blending components are not counted in data on finished aviation gasoline. Gas Plant Operator Any firm,

  20. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Prices, Sales Volumes & Stocks by State Definitions Key Terms Definition Aviation Gasoline (Finished) A complex mixture of relatively volatile hydrocarbons with or without small quantities of additives, blended to form a fuel suitable for use in aviation reciprocating engines. Fuel specifications are provided in ASTM Specification D 910 and Military Specification MIL-G-5572. Note: Data on blending components are not counted in data on finished aviation gasoline. Gas Plant Operator Any firm,

  1. HSEP Committee Meeting - Transcribed Flipchart Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Flipchart Notes August 8, 2013 Safety Culture Next Steps 1. Continue to get periodic briefings from SCIPT - progress on action items, contractor engagement, etc. 2. Get update on HSS review Page 1 DS Tanks/Flammable Gas - Next Steps 1. Update after DOE report on tank flow rate monitoring is available (Jan/Feb) 2. Tom w/follow up with concerns about pressurization alarms Page 2 Emergency Preparedness/Response: Input - Strategies for Awareness 1. Use real examples when trying to increase

  2. labNotes | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LabNotes NETL Validates Innovative Spectrometry Technique libs-PIC.JPG Graphic representation of in situ measurements of calcium carbonate dissolution under rising CO2 pressure using underwater laser-induced breakdown spectroscopy. Image used as the front cover for the Journal of Analytical Atomic Spectrometry's July 2016 issue. An article highlighting NETL's research into the use of laser spectrometry to collect data vital to ensuring the efficacy and safety of geologic carbon storage sites was

  3. eNews Note of Appreciation

    National Nuclear Security Administration (NNSA)

    3 Issue 25 ASC eNews Quarterly Newsletter September 2013 A Note of Appreciation Reeta Garber The ASC Program would like to recognize Reeta Garber for her leadership in designing and developing programmatic communications tools and activities and to wish her the very best as she retires (again) to begin a new phase in her life. Since 1998 Reeta has supported the ASC Program as an important member of the core team responsible for spreading the word about DOE/NNSA laboratory and Federal efforts in

  4. MICROBOONE-NOTE-1006-PUB Study Towards

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6-PUB Study Towards an Event Selection for Neutral Current Inclusive Single π 0 Production in MicroBooNE The MicroBooNE Collaboration May 3, 2016 Abstract This note describes a Monte Carlo study towards an event selection for the neutrino induced Neutral Current (NC) single π 0 cross section using the MicroBooNE detector. The NC single π 0 channel is especially important in neutrino oscillation experiments as it is one of the main backgrounds in any ν e or ν e appearance search. This

  5. Closure Report for Corrective Action Unit 224: Decon Pad and Septic Systems, Nevada Test Site, Nevada

    SciTech Connect (OSTI)

    NSTec Environmental Restoration

    2007-10-01

    Corrective Action Unit (CAU) 224 is located in Areas 02, 03, 05, 06, 11, and 23 of the Nevada Test Site, which is situated approximately 65 miles northwest of Las Vegas, Nevada. CAU 224 is listed in the Federal Facility Agreement and Consent Order (FFACO) of 1996 as Decon Pad and Septic Systems and is comprised of the following nine Corrective Action Sites (CASs): CAS 02-04-01, Septic Tank (Buried); CAS 03-05-01, Leachfield; CAS 05-04-01, Septic Tanks (4)/Discharge Area; CAS 06-03-01, Sewage Lagoons (3); CAS 06-05-01, Leachfield; CAS 06-17-04, Decon Pad and Wastewater Catch; CAS 06-23-01, Decon Pad Discharge Piping; CAS 11-04-01, Sewage Lagoon; and CAS 23-05-02, Leachfield. The Nevada Division of Environmental Protection (NDEP)-approved corrective action alternative for CASs 02-04-01, 03-05-01, 06-03-01, 11-04-01, and 23-05-02 is no further action. As a best management practice, the septic tanks and distribution box were removed from CASs 02-04-01 and 11-04-01 and disposed of as hydrocarbon waste. The NDEP-approved correction action alternative for CASs 05-04-01, 06-05-01, 06-17-04, and 06-23-01 is clean closure. Closure activities for these CASs included removing and disposing of radiologically and pesticide-impacted soil and debris. CAU 224 was closed in accordance with the NDEP-approved CAU 224 Corrective Action Plan (CAP). The closure activities specified in the CAP were based on the recommendations presented in the CAU 224 Corrective Action Decision Document (U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, 2005). This Closure Report documents CAU 224 closure activities. During closure activities, approximately 60 cubic yards (yd3) of mixed waste in the form of soil and debris; approximately 70 yd{sup 3} of sanitary waste in the form of soil, liquid from septic tanks, and concrete debris; approximately 10 yd{sup 3} of hazardous waste in the form of pesticide-impacted soil; approximately 0.5 yd{sup 3} of universal waste in

  6. Meeting Notes re NOI for Convention on Supplementary Compensation |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Notes re NOI for Convention on Supplementary Compensation Meeting Notes re NOI for Convention on Supplementary Compensation notes from meeting on Convention on Supplementary Compensation Meeting Notes re NOI for Convention on Supplementary Compensation (45.83 KB) More Documents & Publications Convention on Supplementary Compensation for Nuclear Damage Contingent Cost Allocation NOPR NEI CIGNLCommentsDOECSCRulemaking11-30-10.doc

  7. DOE Durability Working Group October 2011 Meeting Notes | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy 1 Meeting Notes DOE Durability Working Group October 2011 Meeting Notes Meeting notes from the Fall 2011 Durability Working Group (DWG) Meeting sponsored by the U.S. Department of Energy (DOE) Fuel Cell Technologies Program. Notes also include a summary of progress on action items from the Spring 2011 DWG meeting. durability_working_group_minutes_oct_2011.pdf (54.58 KB) More Documents & Publications DOE Durability Working Group October 2010 Meeting Minutes DOE Durability Working

  8. Thermal neutron detection using a silicon pad detector and {sup 6}LiF removable converters

    SciTech Connect (OSTI)

    Barbagallo, Massimo; Cosentino, Luigi; Marchetta, Carmelo; Pappalardo, Alfio; Scire, Carlotta; Scire, Sergio; Schillaci, Maria; Vecchio, Gianfranco; Finocchiaro, Paolo; Forcina, Vittorio; Peerani, Paolo; Vaccaro, Stefano

    2013-03-15

    A semiconductor detector coupled with a neutron converter is a good candidate for neutron detection, especially for its compactness and reliability if compared with other devices, such as {sup 3}He tubes, even though its intrinsic efficiency is rather lower. In this paper we show a neutron detector design consisting of a 3 cm Multiplication-Sign 3 cm silicon pad detector coupled with one or two external {sup 6}LiF layers, enriched in {sup 6}Li at 95%, placed in contact with the Si active surfaces. This prototype, first characterized and tested at INFN Laboratori Nazionali del Sud and then at JRC Ispra, was successfully shown to detect thermal neutrons with the expected efficiency and an outstanding gamma rejection capability.

  9. The MicroBooNE Experiment - Public Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Public Notes Page Back to the Publications Page 7/4/16 MICROBOONE-NOTE-1019-PUB Convolutional Neural Networks Applied to Neutrino Events in a Liquid Argon Time Projection Chamber 7/4/16 MICROBOONE-NOTE-1017-PUB A Method to Extract the Charge Distribution Arriving at the TPC Wire Planes in MicroBooNE 7/4/16 MICROBOONE-NOTE-1016-PUB Noise Characterization and Filtering in the MicroBooNE TPC 7/4/16 MICROBOONE-NOTE-1015-PUB The Pandora multi-algorithm approach to automated pattern recognition in LAr

  10. Process for 3D chip stacking

    DOE Patents [OSTI]

    Malba, Vincent

    1998-01-01

    A manufacturable process for fabricating electrical interconnects which extend from a top surface of an integrated circuit chip to a sidewall of the chip using laser pantography to pattern three dimensional interconnects. The electrical interconnects may be of an L-connect or L-shaped type. The process implements three dimensional (3D) stacking by moving the conventional bond or interface pads on a chip to the sidewall of the chip. Implementation of the process includes: 1) holding individual chips for batch processing, 2) depositing a dielectric passivation layer on the top and sidewalls of the chips, 3) opening vias in the dielectric, 4) forming the interconnects by laser pantography, and 5) removing the chips from the holding means. The process enables low cost manufacturing of chips with bond pads on the sidewalls, which enables stacking for increased performance, reduced space, and higher functional per unit volume.

  11. Process for 3D chip stacking

    DOE Patents [OSTI]

    Malba, V.

    1998-11-10

    A manufacturable process for fabricating electrical interconnects which extend from a top surface of an integrated circuit chip to a sidewall of the chip using laser pantography to pattern three dimensional interconnects. The electrical interconnects may be of an L-connect or L-shaped type. The process implements three dimensional (3D) stacking by moving the conventional bond or interface pads on a chip to the sidewall of the chip. Implementation of the process includes: (1) holding individual chips for batch processing, (2) depositing a dielectric passivation layer on the top and sidewalls of the chips, (3) opening vias in the dielectric, (4) forming the interconnects by laser pantography, and (5) removing the chips from the holding means. The process enables low cost manufacturing of chips with bond pads on the sidewalls, which enables stacking for increased performance, reduced space, and higher functional per unit volume. 3 figs.

  12. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Plant Processing Definitions Key Terms Definition Extraction Loss The reduction in volume of natural gas due to the removal of natural gas liquid constituents such as ethane, propane, and butane at natural gas processing plants. Natural Gas Processed Natural gas that has gone through a processing plant. Natural Gas Processing Plant A facility designed to recover natural gas liquids from a stream of natural gas which may or may not have passed through lease separators and/or field separation

  13. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Processing of Fresh Feed Input Definitions Key Terms Definition Barrel A unit of volume equal to 42 U.S. gallons. Catalytic Cracking The refining process of breaking down the larger, heavier, and more complex hydrocarbon molecules into simpler and lighter molecules. Catalytic cracking is accomplished by the use of a catalytic agent and is an effective process for increasing the yield of gasoline from crude oil. Catalytic cracking processes fresh feeds and recycled feeds. Catalytic Hydrocracking

  14. BNL ALARA Center: ALARA Notes, No. 9

    SciTech Connect (OSTI)

    Khan, T.A.; Xie, J.W.; Beckman, M.C.

    1994-02-01

    This issue of the Brookhaven National Laboratory`s Alara Notes includes the agenda for the Third International Workshop on ALARA and specific instructions on the use of the on-line fax-on-demand service provided by BNL. Other topics included in this issue are: (1) A discussion of low-level discharges from Canadian nuclear plants, (2) Safety issues at French nuclear plants, (3) Acoustic emission as a means of leak detection, (4) Replacement of steam generators at Doel-3, Beaznau, and North Anna-1, (5) Remote handling equipment at Bruce, (6) EPRI`s low level waste program, (7) Radiation protection during concrete repairs at Savannah River, (8) Reactor vessel stud removal/repair at Comanche Peak-1, (9) Rework of reactor coolant pump motors, (10) Restoration of service water at North Anna-1 and -2, (11) Steam generator tubing problems at Mihama-1, (12) Full system decontamination at Indian Point-2, (13) Chemical decontamination at Browns Ferry-2, and (14) Inspection methodolody in France and Japan.

  15. Consortium for Energy Efficiency (CEE) Notes_ Clothes Dryer Test Procedure

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy Consortium for Energy Efficiency (CEE) Notes_ Clothes Dryer Test Procedure Consortium for Energy Efficiency (CEE) Notes_ Clothes Dryer Test Procedure CEE and DOE staff discussed the importance of relying on the DOE test method as the sole metric for efficiency and energy use reporting. CEE_Notes_ClothesDryerTestProcedure_25Apr2016 (352.34 KB) More Documents & Publications 2015-03-23 Issuance: Energy Conservation Standards for Residential Clothes Dryers; Request for

  16. Sample Memorandum to Reactivate a Directive Placed on Hold (NOTE...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sample Memorandum to Reactivate a Directive Placed on Hold (NOTE: Per Office of Executive Secretariat procedures, please use Calibri, 12 point font for this memorandum.) (Effective...

  17. Workshop Notes from ""Compressed Natural Gas and Hydrogen Fuels...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hydrogen Fuels: Lessons Learned for the Safe Deployment of Vehicles"" Workshop, December 10-11, 2009 Workshop Notes from ""Compressed Natural Gas and Hydrogen Fuels: Lessons ...

  18. West Flank Coso FORGE: well photos and notes

    SciTech Connect (OSTI)

    Doug Blankenship

    2015-12-21

    Photos and detailed down-hole lithology notes for wells CGEH-1 and 74-2 at the West Flank Coso, Ca FORGE location.

  19. COLLOQUIUM - PLEASE NOTE SPECIAL DATE/TIME: The Magnetospheric...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    COLLOQUIUM - PLEASE NOTE SPECIAL DATETIME: The Magnetospheric MultiScale Mission Investigation of Magnetic Reconnection Professor Roy Torbert University of New Hampshire ...

  20. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    as sulfur and various metals; Drip gases, and liquid hydrocarbons produced from tar sands, gilsonite, and oil shale. Liquids produced at natural gas processing plants are excluded. ...

  1. MEMS packaging with etching and thinning of lid wafer to form lids and expose device wafer bond pads

    SciTech Connect (OSTI)

    Chanchani, Rajen; Nordquist, Christopher; Olsson, Roy H; Peterson, Tracy C; Shul, Randy J; Ahlers, Catalina; Plut, Thomas A; Patrizi, Gary A

    2013-12-03

    In wafer-level packaging of microelectromechanical (MEMS) devices a lid wafer is bonded to a MEMS wafer in a predermined aligned relationship. Portions of the lid wafer are removed to separate the lid wafer into lid portions that respectively correspond in alignment with MEMS devices on the MEMS wafer, and to expose areas of the MEMS wafer that respectively contain sets of bond pads respectively coupled to the MEMS devices.

  2. Acquisition Guide Chapters 4.1- Procurement and Assistance Data System (PADS) and 4.3- Requirements for the Industry Interactive Procurement System (IIPS)

    Broader source: Energy.gov [DOE]

    With the implementation of Strategic Integrated Procurement Enterprise System (STRIPES), Acquisition Guide Chapters 4.1 - Procurement and Assistance Data System (PADS) and 4.3 - Requirements for the Industry Interactive Procurement System (IIPS) are hereby rescinded.

  3. Natural Gas Processing Plants in the United States: 2010 Update...

    Gasoline and Diesel Fuel Update (EIA)

    3. Natural Gas Processing Plants Utilization Rates Based on 2008 Flows Figure 3. Natural Gas Processing Plants Utilization Rates Based on 2008 Flows Note: Average utilization rates...

  4. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Plant Liquids Proved Reserves Definitions Key Terms Definition Natural Gas Liquids Those hydrocarbons in natural gas which are separated from the gas through the processes of absorption, condensation, adsorption, or other methods in gas processing or cycling plants. Generally such liquids consist of propane and heavier hydrocarbons and are commonly referred to as condensate, natural gasoline, or liquefied petroleum gases. Where hydrocarbon components lighter than propane are recovered as

  5. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Natural Gas Plant Liquids Production Definitions Key Terms Definition Natural Gas Liquids Those hydrocarbons in natural gas which are separated from the gas through the processes of absorption, condensation, adsorption, or other methods in gas processing or cycling plants. Generally such liquids consist of propane and heavier hydrocarbons and are commonly referred to as condensate, natural gasoline, or liquefied petroleum gases. Where hydrocarbon components lighter than propane are recovered as

  6. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Wellhead Value & Marketed Production Definitions Key Terms Definition Marketed Production Gross withdrawals less gas used for repressuring, quantities vented and flared, and nonhydrocarbon gases removed in treating or processing operations. Includes all quantities of gas used in field and processing plant operations. Production The volume of natural gas withdrawn from reservoirs less (1) the volume returned to such reservoirs in cycling, repressuring of oil reservoirs, and conservation

  7. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Utilization and Capacity Definitions Key Terms Definition Atmospheric Crude Oil Distillation The refining process of separating crude oil components at atmospheric pressure by heating to temperatures of about 600º to 750º F (depending on the nature of the crude oil and desired products) and subsequent condensing of the fractions by cooling. Barrel A unit of volume equal to 42 U.S. gallons. Barrels Per Calendar Day The amount of input that a distillation facility can process under usual

  8. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Plant Field Production Definitions Key Terms Definition Barrel A unit of volume equal to 42 U.S. gallons. Butylene (C4H8) An olefinic hydrocarbon recovered from refinery processes. Ethane (C2H6) A normally gaseous straight-chain hydrocarbon. It is a colorless paraffinic gas that boils at a temperature of -127.48º F. It is extracted from natural gas and refinery gas streams. Field Production Represents crude oil production on leases, natural gas liquids production at natural gas processing

  9. MICROBOONE-NOTE-1016-PUB Noise Characterization

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6-PUB Noise Characterization and Filtering in the MicroBooNE TPC The MicroBooNE Collaboration (Dated: July 5, 2016) In large liquid argon time projection chambers (LArTPCs), TPC signal processing, which recovers the number of ionized electrons arriving at the anode plane from the raw digitized wire signals, is a crucial step towards automated event reconstruction. The first stage of signal processing is the identification and removal of any excess TPC noise with minimal impact on the true

  10. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Lease Condensate Production Definitions Key Terms Definition Lease Condensate A mixture consisting primarily of pentanes and heavier hydrocarbons which is recovered as a liquid from natural gas in lease separation facilities. This category excludes natural gas plant liquids, such as butane and propane, which are recovered at downstream natural gas processing plants or facilities. Production, Lease Condensate The volume of lease condensate produced during the report year. Lease condensate volumes

  11. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Gross Withdrawals and Production Definitions Key Terms Definition Coalbed Methane Methane is generated during coal formation and is contained in the coal microstructure. Typical recovery entails pumping water out of the coal to allow the gas to escape. Methane is the principal component of natural gas. Coalbed methane can be added to natural gas pipelines without any special treatment. Dry Natural Gas Production The process of producing consumer-grade natural gas. Natural gas withdrawn from

  12. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Processing Area Definitions Key Terms Definition Aviation Gasoline Blending Components Naphthas which will be used for blending or compounding into finished aviation gasoline (e.g., straight-run gasoline, alkylate, reformate, benzene, toluene, and xylene). Excludes oxygenates (alcohols, ethers), butane, and pentanes plus. Oxygenates are reported as other hydrocarbons, hydrogen, and oxygenates. Barrel A unit of volume equal to 42 U.S. gallons. Conventional Blendstock for Oxygenate Blending (CBOB)

  13. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Number and Capacity of Petroleum Refineries Definitions Key Terms Definition Atmospheric Crude Oil Distillation Capacity The refining process of separating crude oil components at atmospheric pressure by heating to temperatures of about 600º to 750º F (depending on the nature of the crude oil and desired products) and subsequent condensing of the fractions by cooling. Barrel A unit of volume equal to 42 U.S. gallons. Barrels Per Calendar Day The amount of input that a distillation facility can

  14. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Charge Capacity of Operable Petroleum Refineries Definitions Key Terms Definition Atmospheric Crude Oil Distillation Capacity The refining process of separating crude oil components at atmospheric pressure by heating to temperatures of about 600º to 750º F (depending on the nature of the crude oil and desired products) and subsequent condensing of the fractions by cooling. Barrel A unit of volume equal to 42 U.S. gallons. Barrels Per Calendar Day The amount of input that a distillation

  15. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Stocks by Type Definitions Key Terms Definition Alaskan in Transit Alaskan crude oil stocks in transit by water between Alaska and the other States, the District of Columbia, Puerto Rico, and the Virgin Islands. Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of

  16. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Natural Gas Plant Net Stocks Definitions Key Terms Definition Barrel A unit of volume equal to 42 U.S. gallons. Butylene (C4H8) An olefinic hydrocarbon recovered from refinery processes. Ethane (C2H6) A normally gaseous straight-chain hydrocarbon. It is a colorless paraffinic gas that boils at a temperature of -127.48º F. It is extracted from natural gas and refinery gas streams. Isobutane (C4H10) A normally gaseous branch-chain hydrocarbon. It is a colorless paraffinic gas that boils at a

  17. Workshop Notes from "Compressed Natural Gas and Hydrogen Fuels...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    exchange information among experts from China, India, and the U.S. on compressed natural ... It should be noted that in 2008, there were about 490,000 CNG vehicles in China. China ...

  18. Federal Utility Partnership Working Group Meeting Notes | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Federal Utility Partnership Working Group Meeting Notes Spring 2013 Meeting Report (510.93 KB) Fall 2012 Meeting Report (606.19 KB) Spring 2012 Meeting Report (307.53 KB) Fall 2011 ...

  19. PLEASE NOTE THURSDAY DATE - COLLOQUIUM: Professor Ralph Roskies...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    May 23, 2013, 4:15pm to 5:30pm Colloquia MBG Auditorium PLEASE NOTE THURSDAY DATE - COLLOQUIUM: Professor Ralph Roskies - "Big Data at the Pittsburgh Supercomputing Center" ...

  20. Repairable chip bonding/interconnect process

    DOE Patents [OSTI]

    Bernhardt, A.F.; Contolini, R.J.; Malba, V.; Riddle, R.A.

    1997-08-05

    A repairable, chip-to-board interconnect process which addresses cost and testability issues in the multi-chip modules is disclosed. This process can be carried out using a chip-on-sacrificial-substrate technique, involving laser processing. This process avoids the curing/solvent evolution problems encountered in prior approaches, as well is resolving prior plating problems and the requirements for fillets. For repairable high speed chip-to-board connection, transmission lines can be formed on the sides of the chip from chip bond pads, ending in a gull wing at the bottom of the chip for subsequent solder. 10 figs.

  1. Repairable chip bonding/interconnect process

    DOE Patents [OSTI]

    Bernhardt, Anthony F.; Contolini, Robert J.; Malba, Vincent; Riddle, Robert A.

    1997-01-01

    A repairable, chip-to-board interconnect process which addresses cost and testability issues in the multi-chip modules. This process can be carried out using a chip-on-sacrificial-substrate technique, involving laser processing. This process avoids the curing/solvent evolution problems encountered in prior approaches, as well is resolving prior plating problems and the requirements for fillets. For repairable high speed chip-to-board connection, transmission lines can be formed on the sides of the chip from chip bond pads, ending in a gull wing at the bottom of the chip for subsequent solder.

  2. LLW Notes, Volume 12, Number 2

    SciTech Connect (OSTI)

    Norris, C.; Brown, H.; Colsant, J.; Lovinger, T.; Scheele, L.; Shaker, M.A.

    1997-02-01

    Contents include the following articles: National Environmental Justice Advisory Council considers Ward Valley resolution; NGA urges Congressional and Presidential support for low-level radioactive waste compacts and transfer of federal land in Ward Valley; RFP issued for SEIS on Ward Valley land transfer; Illinois siting criteria finalized; Consideration of tribal concerns during Ward Valley siting process; State legislators` LLRW working group meets in D.C.; Upcoming state and compact events; Court calendar; Texas compact legislation introduced in Congress; Superfund reform is a priority for 105th Congress; High-level waste bill gets off to an early start; Fort Mojave petition NEJAC for Ward Valley resolution; EPA withdraws cleanup rule from OMB; Board ruling raises doubts about proposed Louisiana enrichment facility; DOE recommends external regulation by NRC; and Supplement--Background on environmental justice.

  3. U.S. Department of Energy Onboard Storage Tank Workshop Notes...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Onboard Storage Tank Workshop Notes U.S. Department of Energy Onboard Storage Tank Workshop Notes These notes and action items were derived from the Onboard Storage Tank Workshop ...

  4. ,"Total Crude Oil and Petroleum Products Net Receipts by Pipeline, Tanker, Barge and Rail between PAD Districts"

    U.S. Energy Information Administration (EIA) Indexed Site

    Net Receipts by Pipeline, Tanker, Barge and Rail between PAD Districts" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","Total Crude Oil and Petroleum Products Net Receipts by Pipeline, Tanker, Barge and Rail between PAD Districts",5,"Monthly","6/2016","1/15/1981" ,"Release

  5. High School Co-op Program Selection Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    student will be scheduled for the new hire orientation. Please note: Students should not report to their worksite until they have gone through the hiring and orientation process....

  6. A note on entropic force and brane cosmology

    SciTech Connect (OSTI)

    Ling, Yi; Wu, Jian-Pin E-mail: jianpinwu@yahoo.com.cn

    2010-08-01

    Recently Verlinde proposed that gravity is an entropic force caused by information changes when a material body moves away from the holographic screen. In this note we apply this argument to brane cosmology, and show that the cosmological equation can be derived from this holographic scenario.

  7. Tribal Consultation and Stakeholder Outreach Meeting Notes and Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Strategy on the Arctic Region (NSAR) - Ten Year Renewable Energy Strategy Tribal Consultation and Stakeholder Outreach Meeting Notes and Analysis Prepared by Denali Daniels and Associates, Inc. Fall 2014 Office of Indian Energy Table o f C ontents Executive S ummary .............................................................................................................................................. 2 --- 6 Background

  8. LLW Notes, Volume 9, Number 6. October 1994

    SciTech Connect (OSTI)

    1994-10-01

    LLW Notes is distributed to Low-Level Radioactive Waste Forum Participants and other state and compact officials identified by those Participants to receive LLW Notes. The Low-Level Radioactive Waste Forum is an association of state and compact representatives appointed by governors and compact commissions, established to facilitate state and compact commission implementation of the Low- Level Radioactive Waste Policy Act of 1980 and the Low-Level Radioactive Waste Policy Amendments Act of 1985 and to promote the objectives of low-level radioactive waste regional compacts. The Forum provides an opportunity for states and compacts to share information with one another and to exchange views with officials of federal agencies and other interested parties.

  9. Application note : using open source schematic capture tools with Xyce.

    SciTech Connect (OSTI)

    Russo, Thomas V.

    2013-08-01

    The development of the XyceTM Parallel Electronic Simulator has focused entirely on the creation of a fast, scalable simulation tool, and has not included any schematic capture or data visualization tools. This application note will describe how to use the open source schematic capture tool gschem and its associated netlist creation tool gnetlist to create basic circuit designs for Xyce, and how to access advanced features of Xyce that are not directly supported by either gschem or gnetlist.

  10. State Energy Data System 2014 Price and Expenditure Technical Notes

    Gasoline and Diesel Fuel Update (EIA)

    Price and Expenditure Technical Notes U.S. Energy Information Administration | State Energy Data 2014: Prices and Expenditures 3 Purpose The State Energy Data System (SEDS) was developed and is maintained and operated by the U.S. Energy Information Administration (EIA). The goal in maintaining SEDS is to create historical time series of energy production, consumption, prices, and expenditures by state that are defined as consistently as possible over time and across sectors. SEDS exists for two

  11. - Resilient Electric Distribution Grid R&D Workshop Notes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    th - Resilient Electric Distribution Grid R&D Workshop Notes Breakout session: Identification of R&D areas for Design, preparedness, and planning for a resilient electric distribution grid Moderator: Russell Bent, Los Alamos National Laboratory  Segmentation and recombination were considered as the first main area. o One of participants stated it could be in the form of a microgrid  Data sharing and operation is also important especially in real-time o GIS was suggested

  12. June 2016 LabNotes | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    June 2016 LabNotes Intern Publishes Paper on the Effects of Hydraulic Fracturing Fluid on Marcellus Shale For the last two and a half years, NETL ORISE intern Matt Dieterich has been working closely with NETL researchers, Barbara Kutchko and Angela Goodman, learning to use some of the cutting-edge analytical equipment at NETL. Recently, their research efforts have culminated in the publication of Dieterich's first peer-reviewed paper. The article, "Characterization of Marcellus Shale and

  13. POST CLOSURE INSPECTION REPORT FOR CORRECTIVE ACTION UNIT 92: AREA 6 DECON PAD FACILITY, NEVADA TEST SITE NEVADA, FOR THE PERIOD JANUARY 2004 - DECEMBER 2004

    SciTech Connect (OSTI)

    BECHTEL NEVADA

    2005-03-01

    This Post-Closure Inspection Report provides an analysis and summary of inspections for Corrective Action Unit (CAU) 92, Area 6 Decon Pond Facility, Nevada Test Site, Nevada. CAU 92 was closed in accordance with the Resource Conservation and Recovery Act (RCRA) Part B Operational Permit (Nevada Division of Environmental Protection, 1995) and the Federal Facility Agreement and Consent Order of 1996 on May 11, 1999. CAU 92 consists of two Corrective Action Sites (CASs): CAS 06-04-01, Decon Pad oil/Water Separator; and CAS 06-05-02, Decontamination Pond (RCRA). Both CASs have use restrictions; however, only CAS 06-05-02, Decontamination Pond (RCRA), requires post-closure inspections. CAS 06-04-01, Decon Pad Oil/Water Separator, is located inside the fence at the Building 6-605 compound. This report covers the annual period January 2004 through December 2004.

  14. Notes from Financial and Physical Oil Market Linkages

    Gasoline and Diesel Fuel Update (EIA)

    Notes from Financial and Physical Oil Market Linkages August 24, 2011 Session 1: 9:30 a.m. - 11:00 a.m. Paper Title: Does 'Paper Oil' Matter? Presenter: Michel Robe, American University Discussant: James Smith, Southern Methodist University Paper Abstract We construct a uniquely detailed, comprehensive dataset of trader positions in U.S. energy futures markets. We find considerable changes in the make-up of the open interest between 2000 and 2010 and show that these changes impact asset pricing.

  15. MICROBOONE-NOTE-1008-PUB Michel Electron Reconstruction Using

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8-PUB Michel Electron Reconstruction Using the MicroBooNE LArTPC Cosmic Data The MicroBooNE Collaboration August 25, 2016 Abstract MicroBooNE is a Liquid Argon Time Projection Chamber (LArTPC) neutrino detector located in the Booster Neutrino Beamline at Fermilab which began collecting neutrino data in October 2015. MicroBooNE aims to explore the low-energy excess in the ν e spectrum reported by MiniBooNE as well as perform ν-Ar cross-section measurements. In this note, we present the current

  16. DOE-EERE Durability Working Group Meeting Notes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE-EERE Durability Working Group (DWG) Meeting Thursday, October 13, 2011 Boston, MA Meeting Notes D. Myers and R. Borup Meeting Agenda 6:30 pm Welcome and introductory comments Debbie Myers (Argonne) and Rod Borup (Los Alamos) - co-chairs 6:40-7:45 pm Descriptions and summaries of results of modeling efforts in durability projects Dane Morgan, University of Wisconsin-Madison Srikanth Arisetty, ANL Adam Weber, LBNL Shanna Knights, Ballard Sergei Burlatsky, UTC Power Jean St-Pierre, University

  17. COLLOQUIUM: NOTE SPECIAL DATE - THURSDAY: Unique Vulnerability of the New

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    York/New Jersey Metro Region to Hurricane Destruction - A New Perspective Based on Recent Research on Irene 2011 and Sandy 2012 | Princeton Plasma Physics Lab February 28, 2013, 4:15pm to 5:30pm Colloquia MBG Auditorium COLLOQUIUM: NOTE SPECIAL DATE - THURSDAY: Unique Vulnerability of the New York/New Jersey Metro Region to Hurricane Destruction - A New Perspective Based on Recent Research on Irene 2011 and Sandy 2012 Professor Nicholas K. Coch Queens College CUNY In the last two years. the

  18. V-147: IBM Lotus Notes Mail Client Lets Remote Users Execute...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    7: IBM Lotus Notes Mail Client Lets Remote Users Execute Java Applets V-147: IBM Lotus Notes Mail Client Lets Remote Users Execute Java Applets May 2, 2013 - 6:00am Addthis...

  19. ARM - VAP Process - aerinf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsaerinf Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : AERI Noise Filtered (AERINF) Instrument Categories Radiometric The ARM Facility is in the process of improving the temporal resolution of the AERI to collect a sky spectrum every 15-30 seconds. The increased temporal resolution results in less averaging

  20. ARM - VAP Process - beflux

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsbeflux Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Best-Estimate Radiative Flux (BEFLUX) Instrument Categories Radiometric The Best-Estimate Surface Radiative Flux (BEFLUX) VAP processes data from three Southern Great Plains Central Facility radiometer systems when all are available. Before 2001, this VAP used

  1. Evaluation of impact tests of solid steel billet onto concrete pads, and application to generic ISFSI storage cask for tipover and side drop

    SciTech Connect (OSTI)

    Witte, M.C.; Chen, T.F.; Murty, S.S.; Tang, D.T.; Mok, G.C.; Fischer, L.E.; Carlson, R.W.

    1997-05-01

    Twelve tests were performed at LLNL to assess loading conditions on a spent fuel casts for side drops, end drops and tipover events. The tests were performed with a 1/3-scale model concrete pad to benchmark the structural analysis code DYNA3D. The side drop and tipover test results are discussed in this report. The billet and test pad were modified with DYNA3D using material properties and techniques used in earlier tests. The peak or maximum deceleration test results were compared to the simulated analytical results. It was concluded that an analytical model based on DYNA3D code and has been adequately benchmarked for this type of application. A generic or represented cask was modified with the DYNA3D code and evaluated for ISFSI side drop and tipover events. The analytical method can be applied to similar casks to estimate impact loads on storage casks resulting from low-velocity side or tip impacts onto concrete storage pads.

  2. PVMRW2013 Discussion notes. Tues. Feb. 26, 5:30 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    notes. Tues. Feb. 26, 5:30 PVMRW2013 Discussion notes. Tues. Feb. 26, 5:30 We do see some bad diodes going into the field... discussionnotes_tues_530.pdf (93.95 KB) More Documents & Publications PVMRW2013 Discussion notes: Tues. Feb. 26: 10:45 PVMRW2013 Discussion notes Tues. Feb. 26 2013, 2:30 US & Japan TG 4 Activities of QA Forum

  3. PVMRW2013 Wed., Feb. 27, 10:00 Discussion notes: | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0:00 Discussion notes: PVMRW2013 Wed., Feb. 27, 10:00 Discussion notes: We hear that the dampl heat test causes failures that are not representative of field failure... discussionnotes_weds_1000.pdf (103.24 KB) More Documents & Publications PVMRW2013 Discussion notes: Tues. Feb. 26: 10:45 PVMRW2013 Wed., Feb. 27, 1:45 Discussion notes PVMRW2013 Wed., Feb. 27, 3:00 Final Discussion

  4. PVMRW2013 Discussion notes Tues. Feb. 26 2013, 2:30 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    notes Tues. Feb. 26 2013, 2:30 PVMRW2013 Discussion notes Tues. Feb. 26 2013, 2:30 Some participants felt that modules should not be walked on... discussionnotes_tues_230.pdf (103.99 KB) More Documents & Publications PVMRW2013 Discussion notes: Tues. Feb. 26: 10:45

  5. PVMRW2013 Discussion notes: Tues. Feb. 26: 10:45 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    notes: Tues. Feb. 26: 10:45 PVMRW2013 Discussion notes: Tues. Feb. 26: 10:45 If the mechanical properties of the parts of the module... discussionnotes_tues_1045.pdf (109.89 KB) More Documents & Publications PVMRW2013 Discussion notes Tues. Feb. 26 2013, 2:30

  6. V-211: IBM iNotes Multiple Vulnerabilities | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1: IBM iNotes Multiple Vulnerabilities V-211: IBM iNotes Multiple Vulnerabilities August 5, 2013 - 6:00am Addthis PROBLEM: Multiple vulnerabilities have been reported in IBM Lotus iNotes PLATFORM: IBM iNotes 9.x ABSTRACT: IBM iNotes has two cross-site scripting vulnerabilities and an ActiveX Integer overflow vulnerability REFERENCE LINKS: Secunia Advisory SA54436 IBM Security Bulletin 1645503 CVE-2013-3027 CVE-2013-3032 CVE-2013-3990 IMPACT ASSESSMENT: High DISCUSSION: 1) Certain input related

  7. V-229: IBM Lotus iNotes Input Validation Flaws Permit Cross-Site Scripting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attacks | Department of Energy 9: IBM Lotus iNotes Input Validation Flaws Permit Cross-Site Scripting Attacks V-229: IBM Lotus iNotes Input Validation Flaws Permit Cross-Site Scripting Attacks August 28, 2013 - 6:00am Addthis PROBLEM: Several vulnerabilities were reported in IBM Lotus iNotes PLATFORM: IBM Lotus iNotes 8.5.x ABSTRACT: IBM Lotus iNotes 8.5.x contains four cross-site scripting vulnerabilities REFERENCE LINKS: Security Tracker Alert ID 1028954 IBM Security Bulletin 1647740

  8. Remaining Sites Verification Package for the 600-243 Petroleum-Contaminated Soil Bioremediation Pad, Waste Site Reclassification Form 2007-033

    SciTech Connect (OSTI)

    J. M. Capron

    2008-11-07

    The 600-243 waste site consisted of a bioremediation pad for petroleum-contaminated soils resulting from the 1100 Area Underground Storage Tank (UST) upgrades in 1994. In accordance with this evaluation, the verification sampling results support a reclassification of this site to Interim Closed Out. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

  9. Class 1 Permit Modification Notification Addition of Structures within Technical Area 54, Area G, Pad 11, Dome 375 Los Alamos National Laboratory Hazardous Waste Facility Permit, July 2012

    SciTech Connect (OSTI)

    Vigil-Holterman, Luciana R.; Lechel, Robert A.

    2012-08-31

    The purpose of this letter is to notify the New Mexico Environment Department-Hazardous Waste Bureau (NMED-HWB) of a Class 1 Permit Modification to the Los Alamos National Laboratory (LANL) Hazardous Waste Facility Permit issued to the Department of Energy (DOE) and Los Alamos National Security, LLC (LANS) in November 2010. The modification adds structures to the container storage unit at Technical Area (TA) 54 Area G, Pad 11. Permit Section 3.1(3) requires that changes to the location of a structure that does not manage hazardous waste shall be changed within the Permit as a Class 1 modification without prior approval in accordance with Code of Federal Regulations, Title 40 (40 CFR), {section}270.42(a)(1). Structures have been added within Dome 375 located at TA-54, Area G, Pad 11 that will be used in support of waste management operations within Dome 375 and the modular panel containment structure located within Dome 375, but will not be used as waste management structures. The Class 1 Permit Modification revises Figure 36 in Attachment N, Figures; and Figure G.12-1 in Attachment G.12, Technical Area 54, Area G, Pad 11 Outdoor Container Storage Unit Closure Plan. Descriptions of the structures have also been added to Section A.4.2.9 in Attachment A, TA - Unit Descriptions; and Section 2.0 in Attachment G.12, Technical Area 54, Area G, Pad 11 Outdoor Container Storage Unit Closure Plan. Full description of the permit modification and the necessary changes are included in Enclosure 1. The modification has been prepared in accordance with 40 CFR {section}270.42(a)(l). This package includes this letter and an enclosure containing a description of the permit modification, text edits of the Permit sections, and the revised figures (collectively LA-UR-12-22808). Accordingly, a signed certification page is also enclosed. Three hard copies and one electronic copy of this submittal will be delivered to the NMED-HWB.

  10. PVMRW2013 Wed., Feb. 27, 1:45 Discussion notes | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1:45 Discussion notes PVMRW2013 Wed., Feb. 27, 1:45 Discussion notes It could be useful to mix UVA and UVB and test the effects of both at the same time... discussionnotes_weds_145.pdf (118.88 KB) More Documents & Publications PVMRW2013 Wed., Feb. 27, 10:00 Discussion notes: PVMRW2013 Wed., Feb. 27, 3:00 Final Discussion

  11. CEM_Metrics_and_Technical_Note_7_14_10.pdf | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CEM_Metrics_and_Technical_Note_7_14_10.pdf CEM_Metrics_and_Technical_Note_7_14_10.pdf (129.47 KB) More Documents & Publications SEAD-Fact-Sheet.pdf Schematics of a heat pump clothes dryer<br /> Credit: Oak Ridge National Lab Heat Pump Clothes Dryer CEM_Metrics_and_Technical_Note_7_14_10.pdf Wind Vision: A New Era for Wind Power in the United States

  12. Engineering work plan for implementing the Process Condensate Recycle Project at the 242-A evaporator

    SciTech Connect (OSTI)

    Haring, D.S.

    1995-02-02

    The 242-A Evaporator facility is used to reduce the volume of waste stored in the Hanford double shell tanks. This facility uses filtered raw water for cooling, de-entrainment pad sprays, pump seal water, and chemical tank make-up. Some of these uses result in the introduction of filtered raw water into the process, thus increasing the volume of waste requiring evaporation and subsequent treatment by the 200 East Effluent Treatment Facility. The pump seal water and the de-entrainment pad spray systems were identified as candidates for a waste minimization upgrade. This work plan describes the activities associated with the design, installation, testing and initial operation of the process condensate recycle system. Implementation of the process condensate recycle system will permit the use of process condensate in place of raw water for the de-entrainment pad sprays and pump seals. This will reduce the amount of low-level liquid waste and generated during facility operation through source reduction and recycling.

  13. EnPI V4.0 Release Notes and Known Issues | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    notes and known issues for the Energy Performance Indicator (EnPI) Tool v4.0. EnPI Release Notes and Known Issues (101.66 KB) More Documents & Publications EnPI V4.0 User Manual

  14. Process for fabricating device structures for real-time process control of silicon doping

    DOE Patents [OSTI]

    Weiner, Kurt H.

    2001-01-01

    Silicon device structures designed to allow measurement of important doping process parameters immediately after the doping step has occurred. The test structures are processed through contact formation using standard semiconductor fabrication techniques. After the contacts have been formed, the structures are covered by an oxide layer and an aluminum layer. The aluminum layer is then patterned to expose the contact pads and selected regions of the silicon to be doped. Doping is then performed, and the whole structure is annealed with a pulsed excimer laser. But laser annealing, unlike standard annealing techniques, does not effect the aluminum contacts because the laser light is reflected by the aluminum. Once the annealing process is complete, the structures can be probed, using standard techniques, to ascertain data about the doping step. Analysis of the data can be used to determine probable yield reductions due to improper execution of the doping step and thus provide real-time feedback during integrated circuit fabrication.

  15. Corrective Action Decision Document/Closure Report for Corrective Action Unit 559: T Tunnel Compressor/Blower Pad, Nevada Test Site

    SciTech Connect (OSTI)

    NSTec Environmental Restoration

    2010-03-15

    This Corrective Action Decision Document (CADD)/Closure Report (CR) was prepared by the Defense Threat Reduction Agency (DTRA) for Corrective Action Unit (CAU) 559, T-Tunnel Compressor/Blower Pad. This CADD/CR is consistent with the requirements of the Federal Facility Agreement and Consent Order (FFACO) agreed to by the State of Nevada, the U.S. Department of Energy, and the U.S. Department of Defense. Corrective Action Unit 559 is comprised of one Corrective Action Site (CAS): • 12-25-13, Oil Stained Soil and Concrete The purpose of this CADD/CR is to provide justification and documentation supporting the recommendation for closure in place with use restrictions for CAU 559.

  16. Risk assessment of the retrieval of transuranic waste: Pads 1, 2, and 4, Technical Area-54, Area G, Los Alamos National Laboratory

    SciTech Connect (OSTI)

    Wilbert, K.A.; Lyon, B.F.; Hutchison, J.; Holmes, J.A.; Legg, J.L.; Simek, M.P.; Travis, C.C.; Wollert, D.A.

    1995-05-01

    The Risk Assessment for the Retrieval of Transuranic Waste is a comparative risk assessment of the potential adverse human health effects resulting from exposure to contaminants during retrieval and post-retrieval aboveground storage operations of post-1970 earthen-covered transuranic waste. Two alternatives are compared: (1) Immediate Retrieval and (2) Delayed Retrieval. Under the Immediate Retrieval Alternative, retrieval of the waste is assumed to begin immediately, Under the Delayed Retrieval Alternative, retrieval is delayed 10 years. The current risk assessment is on Pads 1, 2, and 4, at Technical Area-54, Area-G, Los Alamos National Laboratory (LANL). Risks are assessed independently for three scenarios: (1) incident-free retrieval operations, (2) incident-free storage operations, and (3) a drum failure analysis. The drum failure analysis evaluates container integrity under both alternatives and assesses the impacts of potential drum failures during retrieval operations. Risks associated with a series of drum failures are potentially severe for workers, off-site receptors, and general on-site employees if retrieval is delayed 10 years and administrative and engineering controls remain constant. Under the Delayed Retrieval Alternative, an average of 300 drums out of 16,647 are estimated to fail during retrieval operations due to general corrosion, while minimal drums are predicted to fail under the Immediate Retrieval Alternative. The results of the current study suggest that, based on risk, remediation of Pads 1, 2, and 4 at LANL should not be delayed. Although risks from incident-free operations in the Delayed Retrieval Alternative are low, risks due to corrosion and drum failures are potentially severe.

  17. Soft Pion Processes

    DOE R&D Accomplishments [OSTI]

    Nambu, Y.

    1968-01-01

    My talk is concerned with a review, not necessarily of the latest theoretical developments, but rather of an old idea which has contributed to recent theoretical activities. By soft pion processes I mean processes in which low energy pions are emitted or absorbed or scattered, just as we use the word soft photon in a similar context. Speaking more quantitatively, we may call a pion soft if its energy is small compared to a natural scale in the reaction. This scale is determined by the particular dynamics of pion interaction, and one may roughly say that a pion is soft if its energy is small compared to the energies of the other individual particles that participate in the reaction. It is important to note at this point that pion is by far the lightest member of all the hadrons, and much of the success of the soft pion formulas depends on this fact.

  18. Calculation notes that support accident scenario and consequence determination of a waste tank criticality

    SciTech Connect (OSTI)

    Crowe, R.D., Westinghouse Hanford

    1996-08-02

    The purpose of this calculation note is to provide the basis forcriticality consequences for the Tank Farm Safety Analysis Report(FSAR). Criticality scenario is developed and details and description of the analysis methods are provided.

  19. Calculation notes that support accident scenario and consequence of the evaporator dump

    SciTech Connect (OSTI)

    Crowe, R.D., Westinghouse Hanford

    1996-09-09

    The purpose of this calculation note is to provide the basis for evaporator dump consequence for the Tank Farm Safety Analysis Report (FSAR). Evaporator Dump scenario is developed and details and description of the analysis methods are provided.

  20. Calculation notes that support accident scenario and consequence of the evaporator dump

    SciTech Connect (OSTI)

    Crowe, R.D.

    1996-09-27

    The purpose of this calculation note is to provide the basis for evaporator dump consequence for the Tank Farm Safety Analysis Report (FSAR). Evaporator Dump scenario is developed and details and description of the analysis methods are provided.

  1. Calculation notes that support accident scenario and consequence determination of a waste tank criticality

    SciTech Connect (OSTI)

    Crowe, R.D.

    1996-09-27

    The purpose of this calculation note is to provide the basis for criticality consequences for the Tank Farm Safety Analysis Report (FSAR). Criticality scenario is developed and details and description of the analysis methods are provided.

  2. Publisher's Note: New mechanism for the top-bottom mass hierarchy...

    Office of Scientific and Technical Information (OSTI)

    New mechanism for the top-bottom mass hierarchy Phys. Rev. D 70, 055006 (2004) Citation Details In-Document Search Title: Publisher's Note: New mechanism for the top-bottom mass ...

  3. Geothermal Industry Ends 2012 on a High Note | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Ends 2012 on a High Note Geothermal Industry Ends 2012 on a High Note December 18, 2012 - 12:14pm Addthis Year-end highlights include new domestic projects, international development and policy benchmarks Washington, D.C. - The past 12 months saw continued economic challenges for many American industries, including those in the renewable energy field, but the country's geothermal community witnessed a year of growth, both domestically and abroad. The Geothermal Energy Association (GEA) today

  4. The art and science of magnet design: Selected notes of Klaus Halbach. Volume 2

    SciTech Connect (OSTI)

    1995-02-01

    This volume contains a compilation of 57 notes written by Dr. Klaus Halbach selected from his collection of over 1650 such documents. It provides an historic snapshot of the evolution of magnet technology and related fields as the notes range from as early as 1965 to the present, and is intended to show the breadth of Dr. Halbach`s interest and ability that have long been an inspiration to his many friends and colleagues. As Halbach is an experimental physicist whose scientific interests span many areas, and who does his most innovative work with pencil and paper rather than at the workbench or with a computer, the vast majority of the notes in this volume were handwritten and their content varies greatly--some reflect original work or work for a specific project, while others are mere clarifications of mathematical calculations or design specifications. As the authors converted the notes to electronic form, some were superficially edited and corrected, while others were extensively re-written to reflect current knowledge and notation. The notes are organized under five categories which reflect their primary content: Beam Position Monitors, (bpm), Current Sheet Electron Magnets (csem), Magnet Theory, (thry), Undulators and Wigglers (u-w), and Miscellaneous (misc). Within the category, they are presented chronologically starting from the most recent note and working backwards in time.

  5. Fluidized-bed combustion of scrap tires: Technical note

    SciTech Connect (OSTI)

    Shang, J.Y.; Mei, J.S.; Notestein, J.E.

    1981-10-01

    An introduction to fluidized-bed combustion (FBC) is presented in Section 2.0. Based on this discussion of its technical development, FBC is then presented as a means of scrap tire disposal. In Section 3.0, scrap tire disposal is reviewed in the categories of (1) physical applications, (2) chemical applications, (3) pyrolysis, and (4) incineration for thermal energy recovery. Scrap tire disposal is reviewed on the basis of (1) environmental acceptability, (2) conservation of resources, (3) impact on existing industries, (4) operational feasibility, and (5) special features. The focus of this report is the fluidized-bed incineration of scrap tires for thermal energy recovery. The factors that affect scrap tire combustion are discussed in Section 4.0. These factors are (1) agitation, (2) temperature, (3) excess air, (4) residence time, (5) feed uniformity, (6) solid waste handling, and (7) pollutants emission control. In reviewing these incineration processes, (1) fuel flexibility, (2) environmental acceptability, (3) combustion efficiency, and (4) operational reliability are discussed. The results from a tire incineration experiment conducted at the Morgantown Energy Technology Center are presented in Section 5.0, and a conceptual fluidized-bed combustor is discussed in Section 6.0. Future considerations in the FBC of scrap tires are discussed in Section 7.0. 8 refs., 6 figs., 6 tabs.

  6. NREL: Process Development and Integration Laboratory - Webmaster

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Webmaster Please enter your name and e-mail address in the boxes provided, then type your message below. When you are finished, click "Send Message." NOTE: If you enter your e-mail address incorrectly, we will be unable to reply. Your name: Your email address: Your message: Send Message Printable Version Process Development & Integration Laboratory Home About the Process Development & Integration Laboratory Capabilities

  7. L3: RTM.MCH.P6.02 Technical Note RNSD-00-

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RTM.MCH.P6.02 Technical Note RNSD-00- 000: Evaluating the Denovo SPN Discretization, Rev 1 Tom Evans Oak Ridge National Laboratory April 5, 2013 CASL-U-2014-0083-000 Technical Note Reactor and Nuclear Systems Division Radiation Transport Group From: Tom Evans, Steven Hamilton Number: RNSD-00-000 Date: April 5, 2013 Subject: Evaluating the Denovo SP N Discretization (Rev. 1) Executive Summary This document describes a preliminary assessment of the SP N discretization in Denovo. Comparison to

  8. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Crude Oil Supply, Disposition, and Ending Stocks by PAD District, 2014 (Thousand Barrels, Except Where Noted) Process PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Supply Field Production .................................................... 19,144 617,116 1,900,521 241,254 404,548 3,182,583 8,719 Alaskan ............................................................. - - - - - - - - - 181,425 497 Lower 48 States ................................................ - - - - - 3,001,158 8,222

  9. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    3.PDF Table 13. Crude Oil Supply, Disposition, and Ending Stocks by PAD District, January 2014 (Thousand Barrels, Except Where Noted) Process PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Supply Field Production .................................................... 1,408 47,406 146,833 17,773 35,538 248,959 8,031 Alaskan ............................................................. - - - - - - - - - 16,799 542 Lower 48 States ................................................ - - - - -

  10. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    0 June 2016 Table 25. Crude Oil Supply, Disposition, and Ending Stocks by PAD District, June 2016 (Thousand Barrels, Except Where Noted) Process PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Supply Field Production .................................................... 1,348 50,177 160,724 19,300 29,479 261,028 8,701 Alaskan ............................................................. - - - - - - - - - 14,103 470 Lower 48 States ................................................ - - - - -

  11. OTS NOTE

    Office of Legacy Management (LM)

    FUSRAP NJ.18 Exxon Research and Engineering Company The Former Standard Oil Development Company Linden, New Jersey Site Function In the spring of 1942, Standard Oil Development ...

  12. OTS NOTE

    Office of Legacy Management (LM)

    2, 1990 TO: W. Alexander Williams FROM: Don Mackenzie &d> SUBJECT: Elimination of 3 Facilities from FUSRAP Enclosed are elimination recommendations for Vitro Chemical Co.,...

  13. OTS NOTE

    Office of Legacy Management (LM)

    January 15, 1991 TO: Alexander Williams FROM: Dan Stout@ SUBJECT: Gruen Watch Company Consideration Recommendation Attached for your review is a consideration recommendation for...

  14. Explanatory Notes

    U.S. Energy Information Administration (EIA) Indexed Site

    data at a State level on 14 petroleum products for various retail and wholesale marketing categories. The Form EIA-782B collects resellerretailer monthly price and volume...

  15. TECHNICAL NOTE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The resulting system bandwidth is slightly less than 80 nm (see Fig. 2 for a sample spectrum). Use of the fiber-optic coupler and microchannel plate does not seriously...

  16. OTS NOTE

    Office of Legacy Management (LM)

    ... Coal ash as : iightly elevated levels of naturally occurring uranium , radium , and thorium which ZXK voted during coal combustion. Nevertheless, several auger samples (Al5 through ...

  17. EDITORS NOTE:

    Office of Environmental Management (EM)

    ... in both alternative fuels and energy ... in biofuels, fuel blends, plug-in hybrids, and more effcient vehicle technologies could ... Social and Economic Trends Perhaps the ...

  18. Explanatory Notes

    U.S. Energy Information Administration (EIA) Indexed Site

    complete enumera- tion has the same nonsampling errors as the sample survey. The sampling error, or standard error of the estimate, is a measure of the variability among the...

  19. OTS NOTE

    Office of Legacy Management (LM)

    ... It is proposed that the Commission pay 4. 50 per pound of contained uranium oxide (U3C31, such pay- .ment to be in addition to a price, f. o. b. Chattanooga, TZM. , of 4. 25 per ...

  20. OTS NOTE

    Office of Legacy Management (LM)

    A telephone interview was conducted with a former Baker-Perkins employee who joined the company in the mid-1970's (see attached Contact Report). The person interviewed was not ...

  1. OTS NOTE

    Office of Legacy Management (LM)

    ...u; a&d de& o* CITY: de54 LPv ---...w-e-- STATE: CIA ------ OWNER(S) Current: 3 H bwd, ---... Owner contacted 0 yes PO; ...

  2. OTS NOTE

    Office of Legacy Management (LM)

    Source Material q Residue 0 Natural Radioactive Material from Non-Nuclear Activities 0 Man-Made 0 Other--- Comment ---...

  3. Regular oscillations and random motion of glass microspheres levitated by a single optical beam in air: Publisher’s note

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Moore, Jeremy; Martin, Leopoldo L.; Maayani, Shai; Kim, Kyu Hyun; Chandrahalim, Hengky; Eichenfield, Matt; Martin, Inocencio R.; Carmon, Tal

    2016-02-19

    The publisher’s note amends a recent publication [Opt. Express 24(3), 2850–2857 (2016)] to include Acknowledgments.

  4. Microsoft PowerPoint - DOE O 413 3B Brief v9 with key points in notes

    Office of Environmental Management (EM)

    [Read-Only] | Department of Energy DOE O 413 3B Brief v9 with key points in notes [Read-Only] Microsoft PowerPoint - DOE O 413 3B Brief v9 with key points in notes [Read-Only] Microsoft PowerPoint - DOE O 413 3B Brief v9 with key points in notes [Read-Only] (2.08 MB) More Documents & Publications Example BCP Template Microsoft PowerPoint - DOE O 413 3B Brief v9 with key points in notes [Read-Only] CD-2, Approve Performance Baseline External Independent Review (EIR) Standard Operating

  5. Workshop Notes from ""Compressed Natural Gas and Hydrogen Fuels: Lessons Learned for the Safe Deployment of Vehicles"" Workshop, December 10-11, 2009

    Broader source: Energy.gov [DOE]

    These notes provide information about the Compressed Natural Gas and Hydrogen Fuels workshop in December 2009.

  6. Catalytic Reforming Downstream Processing of Fresh Feed Input

    U.S. Energy Information Administration (EIA) Indexed Site

    Process: Catalytic Reforming Catalytic Cracking Catalytic Hydrocracking Delayed and Fluid Coking Period-Unit: Monthly-Thousand Barrels per Day Annual-Thousand Barrels per Day Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Process Area Jan-16 Feb-16 Mar-16 Apr-16 May-16 Jun-16 View History U.S. 2,668 2,629 2,824 2,727 2,894 2,994 2010-2016 PADD 1 192 183 180 188 193 195 2010-2016 East Coast 175 167 164 174 176 177

  7. EPICS release 3.11.6 specific documentation -- Release notes for EPICS 3.11.6

    SciTech Connect (OSTI)

    1994-06-07

    These notes cover the following: (1) directions for switching to production APS release R3.11.6; (2) unbundling of channel access clients; (3) access security; (4) channel access additions; synchronous time support; and (5) description of major differences between R3.11.3 and R3.11.6 Also included is a list of new and/or updated documentation for the program.

  8. LLW (Low-Level Waste) Notes, Volume 13, Number 1, February 1998

    SciTech Connect (OSTI)

    1998-02-01

    LLW Notes is a newsletter distributed to Low-Level Radioactive Waste Forum Participants and other state and compact officials. The LLW Forum provides an opportunity for state and compact officials to share information with one another and to exchange views with officials of federal agencies and other interested parties. This issue focuses on the following topics: DOI approves Ward Valley permit application; Project evidentiary hearings begin in Texas; and Summary judgment motions in California breach of contract action.

  9. U.S. Department of Energy Onboard Storage Tank Workshop Notes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    U.S. Department of Energy Onboard Storage Tank Workshop Workshop Notes April 29, 2010 Sandia National Laboratories - Livermore, CA 2 Report from the Onboard Storage Tank Workshop Livermore, CA April 29 th , 2010 The Onboard Storage Tank Workshop was held on April 29 th , 2010, at Sandia National Laboratories (SNL) in Livermore, CA. The Workshop was co-hosted by SNL and the United States Department of Energy (DOE). The purpose of the Workshop was to identify key issues including research and

  10. COLLOQUIUM - NOTE SPECIAL TIME OF 3:15PM: Savannah River National

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Laboratory: Underpinning Critical National Missions | Princeton Plasma Physics Lab May 15, 2013, 3:15pm to 5:30pm Colloquia MBG Auditorium COLLOQUIUM - NOTE SPECIAL TIME OF 3:15PM: Savannah River National Laboratory: Underpinning Critical National Missions Dr. Jeff Griffin Savannah River National Laboratory The Cold War mission of the Savannah River Site in South Carolina was to produce nuclear materials for the national defense. Since the Cold War ended, SRS has continued to ensure United

  11. COLLOQUIUM - PLEASE NOTE SPECIAL DATE/TIME: The Magnetospheric MultiScale

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mission Investigation of Magnetic Reconnection | Princeton Plasma Physics Lab February 21, 2013, 10:30am to 12:00pm Colloquia MBG Auditorium COLLOQUIUM - PLEASE NOTE SPECIAL DATE/TIME: The Magnetospheric MultiScale Mission Investigation of Magnetic Reconnection Professor Roy Torbert University of New Hampshire Presentation: File TC21FEB2013_RBTorbert_COMPRESSED.pptx In late fall 2014, NASA will launch the Magnetospheric Multiscale (MMS) mission to study the kinetic physics of magnetic

  12. L4:PHI.REL.P8.01 VERA Release Notes ID: 2013 VERA RSICC Release

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    L4:PHI.REL.P8.01 VERA Release Notes ID: 2013 VERA RSICC Release (VERA 3.2) Matt Sieger Oak Ridge National Laboratory November 16, 2013 CASL-U-2014-0172-000 DRAFT VERA Release Notes Document VERA Release Notes (DRAFT) Release ID 2013 VERA RSICC Release (VERA 3.2) Release Date Sept. 30, 2013 Support Information Email questions or comments to the VERA development team at casl-support@CASL.gov 1. Introduction VERA, a "Virtual Environment for Reactor Applications", is a collection of

  13. Note: Design principles of a linear array multi-channel effusive metal-vapor atom source

    SciTech Connect (OSTI)

    Jana, B.; Majumder, A.; Thakur, K. B.; Das, A. K.

    2013-10-15

    Atomic beams can easily be produced by allowing atoms to effuse through a channel. In an earlier investigation [A. Majumder et al., Vacuum 83, 989 (2009)], we had designed, fabricated, and characterized an effusive metal-vapor source using collinear-array of multi-channel. In this note, we describe the theoretical basis of designing the source. Atom density in atomic beam has been estimated using a set of analytical expressions for long-channel operated in transparent mode. Parametric studies on aspect ratio of channel, inter-channel separation, beam width, and vertical distance from the source are carried out. They are useful in providing physical picture and optimizing design parameters.

  14. MicroBooNE Detector Stability MICROBOONE-NOTE-1013-PUB The MicroBooNE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MicroBooNE Detector Stability MICROBOONE-NOTE-1013-PUB The MicroBooNE Collaboration June 30, 2016 Abstract The Micro Booster Neutrino Experiment (MicroBooNE) is designed to explore the low- energy excess in the ν e event spectrum reported by the MiniBooNE experiment [1] and to measure ν-Ar cross sections in the 1 GeV energy range. The detector is a liquid argon time projection chamber with wire readout, supplemented with a light detection system based on photo-multiplier tubes (PMTs). The

  15. Hanford Advisory Board FY2014 Work Plan - "A" List - Facilitator notes o

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facilitator notes on midyear status for RAP-lead topics (updated 4/30/14) These are the priority topics that the Board is expected to take action on in FY2014, as agreed to by the TPA and the Board. The timing of these topics drives the need for committee meetings. Their status may change to "topics of interest" if they are delayed or deferred, and if there is agreement to do so among the EIC and Agency Liaisons. Adopted by Consensus, September 6, 2013 Page 1 of 12 Priority Topics -

  16. Summary Notes from 5 March 2008 Generic Technical Issue Discussion on Long-Term Grout Performance

    Office of Environmental Management (EM)

    6, 2008 Page 1 of 6 Summary Notes from 5 March 2008 Generic Technical Issue Discussion on Long-Term Grout Performance Attendees: Representatives from Department of Energy-Headquarters (DOE-HQ) and the U.S. Nuclear Regulatory Commission staff (NRC) met at the DOE offices in Germantown, Maryland on 5 March 2008. Representatives from Department of Energy- Savannah River (DOE-SR), Department of Energy-Idaho (DOE-ID), Department of Energy-Richland (DOE-RL), Department of Energy-River Protection

  17. TEC Tribal Issues Topic Group Conference Call Notes December 15, 1998 11

    Office of Environmental Management (EM)

    Notes December 15, 1998 11 a.m.-Noon EST Participants: Audrey Adamson (UETC), Pamela DeRensis (DOE/EM-22), Margaret Hodge (DOE/AL) Robert Holden (NCAI), Judith Holm (DOE/NTPA), Jerry Pardilla (NTEC), Wilda Portner (SAIC), Elissa Turner (DOE/RW), Heather Westra (Prairie Island Indian Community) and Catherine Volk (DOE/EM). This conference call addressed a number of issues and upcoming events. Discussed: expanding Tribal participation in the Group; upcoming TEC/WG meeting in Jacksonville, Florida;

  18. Attachment 1 - PIC Transcribed Flip Chart Notes Final Meeting Summary Page 12

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - PIC Transcribed Flip Chart Notes Final Meeting Summary Page 12 Public Involvement Committee September 4, 2013 Strategic Planning: Quarters by month * Q1: Oct. - Dec. * Q2: Jan - March * Q3: April - June * Q4: July - Sept. Page 1 Strategic Planning: 2014 Topics (Interactive activity) * = priority topic for discussion at meeting; �= priority for future discussion | Quarter prioritized for discussion (Q1, Q2, Q3, Q4) * 100-F Proposed Plan | *** Q2 * 100 D-H Proposed Plan * Draft Land

  19. Neutron Physics. A Revision of I. Halpern's notes on E. Fermi's lectures in 1945

    DOE R&D Accomplishments [OSTI]

    Beckerley, J.G.

    1951-10-16

    In the Fall of 1945 a course in Neutron Physics was given by Professor Fermi as part of the program of the Los Alamos University. The course consisted of thirty lectures most of which were given by Fermi. In his absence R.F. Christy and E. Segre gave several lectures. The present revision is based upon class notes prepared by I. Halpern with some assistance by B.T. Feld and issued first as document LADC 255 and later with wider circulation as MDDC 320.

  20. Note: Rapid reduction of graphene oxide paper by glow discharge plasma

    SciTech Connect (OSTI)

    Bo, Zheng; Qian, Jiajing; Duan, Liangping; Qiu, Kunzan Yan, Jianhua; Cen, Kefa; Han, Zhao Jun; Ostrikov, Kostya

    2015-05-15

    This note reports on a novel method for the rapid reduction of graphene oxide (GO) paper using a glow discharge plasma reactor. Glow discharge is produced and sustained between two parallel-plate graphite electrodes at a pressure of 240 mTorr. By exposing GO paper at the junction of negative-glow and Faraday-dark area for 4 min, the oxygen-containing groups can be effectively removed (C/O ratio increases from 2.6 to 7.9), while the material integrality and flexibility are kept well. Electrochemical measurements demonstrate that the as-obtained reduced GO paper can be potentially used for supercapacitor application.

  1. Proposal Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proposal Process Network R&D Software-Defined Networking (SDN) Experimental Network Testbeds 100G SDN Testbed Testbed Description Proposal Process Terms and Conditions Dark Fiber Testbed Test Circuit Service Testbed Results Current Testbed Research Previous Testbed Research Performance (perfSONAR) Software & Tools Development Data for Researchers Partnerships Publications Workshops Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1 800-333-7638 (Inside US) 1 510-486-7600

  2. Selection Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Selection Process Selection Process Fellowships will be awarded based on academic excellence, relevance of candidate's research to the laboratory mission in fundamental nuclear science and relevance to Global Security or Science of Campaign missions. Contacts Director Albert Migliori Deputy Franz Freibert 505 667-6879 Email Professional Staff Assistant Susan Ramsay 505 665 0858 Email The Seaborg internal advisory committee will judge applications based on academic excellence, relevance of the

  3. ARM - VAP Process - wpdngps

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Comments? We would love to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Wind Profiler Demonstration Network GPS (WPDNGPS) Instrument Categories ...

  4. ARM - VAP Process - suomigps

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    you Send us a note below or call us at 1-888-ARM-DATA. Send VAP : SuomiNet Global Positioning System (SUOMIGPS) Instrument Categories Atmospheric Profiling General Overview...

  5. ARM - VAP Process - dlprof

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    love to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Doppler Lidar Profiles (DLPROF) Instrument Categories Atmospheric Profiling The ARM...

  6. ARM - VAP Process - rwptemp

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    hear from you Send us a note below or call us at 1-888-ARM-DATA. Send VAP : RWP-Based Virtual Temperature Profile (RWPTEMP) Instrument Categories Derived Quantities and Models...

  7. Notes on the Langevin model for turbulent diffusion of ``marked`` particles

    SciTech Connect (OSTI)

    Rodean, H.C.

    1994-01-26

    Three models for scalar diffusion in turbulent flow (eddy diffusivity, random displacement, and on the Langevin equation) are briefly described. These models random velocity increment based Fokker-Planck equation is introduced as are then examined in more detail in the reverse order. The Fokker-Planck equation is the Eulerian equivalent of the Lagrangian Langevin equation, and the derivation of e outlined. The procedure for obtaining the deterministic and stochastic components of the Langevin equation from Kolmogorov`s 1941 inertial range theory and the Fokker-Planck equation is described. it is noted that a unique form of the Langevin equation can be determined for diffusion in one dimension but not in two or three. The Langevin equation for vertical diffusion in the non-Gaussian convective boundary layer is presented and successively simplified for Gaussian inhomogeneous turbulence and Gaussian homogeneous turbulence in turn. The Langevin equation for Gaussian inhomogeneous turbulence is mathematically transformed into the random displacement model. It is shown how the Fokker-Planck equation for the random displacement model is identical in form to the partial differential equation for the eddy diffusivity model. It is noted that the Langevin model is applicable in two cases in which the other two are not valid: (1) very close in time and distance to the point of scalar release and (2) the non-Gaussian convective boundary layer. The two- and three-dimensional cases are considered in Part III.

  8. ARM - VAP Process - bsrncalc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsbsrncalc Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Baseline Solar Radiation Network (BSRN): calculated solar irradiances (BSRNCALC) Note:bsrncalc is currently inactive and/or retired. Active Dates 1993.10.09 - 1994.08.13 Instrument Categories Radiometric Output Products bsrncalc : Baseline Solar Radiation Network (BSRN):

  9. ARM - VAP Process - sirosopdepth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productssirosopdepth Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Optical Depth from SIROS instruments (SIROSOPDEPTH) Note:sirosopdepth is currently inactive and/or retired. Active Dates 2015.01.09 - 2015.02.12 Instrument Categories Radiometric Output Products sirosopdepth : Solar and Infrared Radiation Observing Station (SIROS): optical

  10. ARM - VAP Process - wsicloud

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productswsicloud Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Whole Sky Imager Cloud Products (WSICLOUD) Note:wsicloud is currently inactive and/or retired. Active Dates 1995.09.20 - 1999.07.15 Instrument Categories Cloud Properties Output Products wsicloud : WSI: derived, cloud numbers, area, perimeter, & more wsicloudden : WSI:

  11. FLUORINATION PROCESS

    DOE Patents [OSTI]

    McMillan, T.S.

    1957-10-29

    A process for the fluorination of uranium metal is described. It is known that uranium will react with liquid chlorine trifluoride but the reaction proceeds at a slow rate. However, a mixture of a halogen trifluoride together with hydrogen fluoride reacts with uranium at a significantly faster rate than does a halogen trifluoride alone. Bromine trifluoride is suitable for use in the process, but chlorine trifluoride is preferred. Particularly suitable is a mixture of ClF/sub 3/ and HF having a mole ratio (moles

  12. Table 5.17 Strategic Petroleum Reserve, 1977-2011 (Thousand Barrels, Except as Noted)

    U.S. Energy Information Administration (EIA) Indexed Site

    7 Strategic Petroleum Reserve, 1977-2011 (Thousand Barrels, Except as Noted) Year Foreign Crude Oil Receipts Domestic Crude Oil Receipts Withdrawals End-of-Year Stocks Days of Petroleum Net Imports 4 Imported by SPR Imported by Others 1,2 Purchases Exchanges 2 Sales Exchanges Quantity Percent of Crude Oil 3 Stocks Percent of Total Petroleum Stocks 1977 7,540 0 370 [5] 0 0 0 7,455 2.1 0.6 1 1978 58,798 0 0 0 0 0 66,860 17.8 5.2 8 1979 24,434 0 4 0 0 0 91,191 21.2 6.8 11 1980 16,067 0 1,296 0 0 0

  13. A Note on the Fisher Ideal Index Decomposition for Structural Change in Energy Intensity

    SciTech Connect (OSTI)

    Boyd, Gale A.; Roop, Joseph M.

    2004-01-01

    By direct appeal to the theory underlying price index numbers used by the energy decomposition literature, this note proposed the chain weighted Fisher Ideal Index as a formula that solves the ''residual problem;'' i.e., the decomposition is not complete in the sense that the components do not add to the whole. The connection to index number theory also allows us to illustrate that the measures of activity used to define energy intensity need not be additive across the sectors that are involved in the decomposition. We give an empirical example using recent U. S. manufacturing data of the Fisher Ideal Index, compared to the Tornquist Divisia Index, a popular index in the energy literature.

  14. Non-Linear Transmission Line (NLTL) Microwave Source Lecture Notes the United States Particle Accelerator School

    SciTech Connect (OSTI)

    Russell, Steven J.; Carlsten, Bruce E.

    2012-06-26

    We will quickly go through the history of the non-linear transmission lines (NLTLs). We will describe how they work, how they are modeled and how they are designed. Note that the field of high power, NLTL microwave sources is still under development, so this is just a snap shot of their current state. Topics discussed are: (1) Introduction to solitons and the KdV equation; (2) The lumped element non-linear transmission line; (3) Solution of the KdV equation; (4) Non-linear transmission lines at microwave frequencies; (5) Numerical methods for NLTL analysis; (6) Unipolar versus bipolar input; (7) High power NLTL pioneers; (8) Resistive versus reactive load; (9) Non-lineaer dielectrics; and (10) Effect of losses.

  15. EPICS release 3.11 specific documentation -- EPICS release notes for 3.11

    SciTech Connect (OSTI)

    1994-01-19

    EPICS release 3.11 is now ready for user testing. A person who wants to set up a simplified application environment to boot an IOC and create databases using R3.11 should follow the directions in Appendix B, page 27, of the EPICS Source/Release Control Manual, Sept. 20, 1993. The R3.11 EPICS path at ANL/APS is /net/phebos/epics/R3.11 so the command to get the new release is /net/phebos/epics/R3.11/Unix/share/bin/getrel /net/phebos/epics/R3.11. An existing R3.8 short form report can be copied to this new directory and used to create a database. ANL/APS is currently testing an Application Developers Source/Release control system. It is not yet ready for general distribution. Attached are the EPICS R3.11 release notes.

  16. Meeting notes of the High Flux Isotope Reactor (HFIR) futures group

    SciTech Connect (OSTI)

    Houser, M.M.

    1995-08-01

    This report is a compilation of the notes from the ten meetings. The group charter is: (1) to identify and characterize the range of possibilities and necessities for keeping the HFIR operating for at least the next 15 years; (2) to identify and characterize the range of possibilities for enhancing the scientific and technical utility of the HFIR; (3) to evaluate the benefits or impacts of these possibilities on the various scientific fields that use the HFIR or its products; (4) to evaluate the benefits or impacts on the operation and maintenance of the HFIR facility and the regulatory requirements; (5) to estimate the costs, including operating costs, and the schedules, including downtime, for these various possibilities; and one possible impact of proposed changes may be to stimulate increased pressure for a reduced enrichment fuel for HFIR.

  17. Process Monitor

    Energy Science and Technology Software Center (OSTI)

    2003-12-01

    This library is used to get process information (eg memory and timing). By setting an environment variable, the runtime system loads libprocmon.so while loading your executable. This library causes the SIGPROF signal to be triggered at time intervals. The procmon signal handler calls various system routines (eg clock_gettime, malinfo, getrusage, and ioctl {accessing the /proc filesystem}) to gather information about the process. The information is then printed to a file which can be viewed graphicallymore » via procmon_plot.pl. This information is obtained via a sampling approach. As with any sampling approach, the information it gathers will not be completely accurate. For example, if you are looking at memory high-water mark the memory allocation and freeing could have occurred between samples and thus would not be "seen" by this program. See "Usage" below for environment variables that affect this monitor (eg time between sampling).« less

  18. Process Limits

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Records Management » Procedures and Instructions Procedures and Instructions keyboard-886462_960_720.jpg Records Management Processes Procedure for Conducting a Records Inventory (PDF) Procedure for Preparing a Records Inventory and Disposition Schedule (RIDS) (PDF) Instructions/Brochures Managing Social Media Records (PDF) Procedures for Departing Employees (PDF) Reminder for Senior Officials (PDF) Your Records Responsibility Pamphlet (PDF) Vital Records Pamphlet (PDF) Records Management

  19. Hydropyrolysis process

    DOE Patents [OSTI]

    Ullman, Alan Z.; Silverman, Jacob; Friedman, Joseph

    1986-01-01

    An improved process for producing a methane-enriched gas wherein a hydrogen-deficient carbonaceous material is treated with a hydrogen-containing pyrolysis gas at an elevated temperature and pressure to produce a product gas mixture including methane, carbon monoxide and hydrogen. The improvement comprises passing the product gas mixture sequentially through a water-gas shift reaction zone and a gas separation zone to provide separate gas streams of methane and of a recycle gas comprising hydrogen, carbon monoxide and methane for recycle to the process. A controlled amount of steam also is provided which when combined with the recycle gas provides a pyrolysis gas for treatment of additional hydrogen-deficient carbonaceous material. The amount of steam used and the conditions within the water-gas shift reaction zone and gas separation zone are controlled to obtain a steady-state composition of pyrolysis gas which will comprise hydrogen as the principal constituent and a minor amount of carbon monoxide, steam and methane so that no external source of hydrogen is needed to supply the hydrogen requirements of the process. In accordance with a particularly preferred embodiment, conditions are controlled such that there also is produced a significant quantity of benzene as a valuable coproduct.

  20. Preliminary evaluation of alternative waste form solidification processes. Volume I. Identification of the processes.

    SciTech Connect (OSTI)

    Treat, R.L.; Nesbitt, J.F.; Blair, H.T.; Carter, J.G.; Gorton, P.S.; Partain, W.L.; Timmerman, C.L.

    1980-04-01

    This document contains preconceptual design data on 11 processes for the solidification and isolation of nuclear high-level liquid wastes (HLLW). The processes are: in-can glass melting (ICGM) process, joule-heated glass melting (JHGM) process, glass-ceramic (GC) process, marbles-in-lead (MIL) matrix process, supercalcine pellets-in-metal (SCPIM) matrix process, pyrolytic-carbon coated pellets-in-metal (PCCPIM) matrix process, supercalcine hot-isostatic-pressing (SCHIP) process, SYNROC hot-isostatic-pressing (SYNROC HIP) process, titanate process, concrete process, and cermet process. For the purposes of this study, it was assumed that each of the solidification processes is capable of handling similar amounts of HLLW generated in a production-sized fuel reprocessing plant. It was also assumed that each of the processes would be enclosed in a shielded canyon or cells within a waste facility located at the fuel reprocessing plant. Finally, it was assumed that all of the processes would be subject to the same set of regulations, codes and standards. Each of the solidification processes converts waste into forms that may be acceptable for geological disposal. Each process begins with the receipt of HLLW from the fuel reprocessing plant. In this study, it was assumed that the original composition of the HLLW would be the same for each process. The process ends when the different waste forms are enclosed in canisters or containers that are acceptable for interim storage. Overviews of each of the 11 processes and the bases used for their identification are presented in the first part of this report. Each process, including its equipment and its requirements, is covered in more detail in Appendices A through K. Pertinent information on the current state of the art and the research and development required for the implementation of each process are also noted in the appendices.

  1. Ceramic Processing

    SciTech Connect (OSTI)

    EWSUK,KEVIN G.

    1999-11-24

    Ceramics represent a unique class of materials that are distinguished from common metals and plastics by their: (1) high hardness, stiffness, and good wear properties (i.e., abrasion resistance); (2) ability to withstand high temperatures (i.e., refractoriness); (3) chemical durability; and (4) electrical properties that allow them to be electrical insulators, semiconductors, or ionic conductors. Ceramics can be broken down into two general categories, traditional and advanced ceramics. Traditional ceramics include common household products such as clay pots, tiles, pipe, and bricks, porcelain china, sinks, and electrical insulators, and thermally insulating refractory bricks for ovens and fireplaces. Advanced ceramics, also referred to as ''high-tech'' ceramics, include products such as spark plug bodies, piston rings, catalyst supports, and water pump seals for automobiles, thermally insulating tiles for the space shuttle, sodium vapor lamp tubes in streetlights, and the capacitors, resistors, transducers, and varistors in the solid-state electronics we use daily. The major differences between traditional and advanced ceramics are in the processing tolerances and cost. Traditional ceramics are manufactured with inexpensive raw materials, are relatively tolerant of minor process deviations, and are relatively inexpensive. Advanced ceramics are typically made with more refined raw materials and processing to optimize a given property or combination of properties (e.g., mechanical, electrical, dielectric, optical, thermal, physical, and/or magnetic) for a given application. Advanced ceramics generally have improved performance and reliability over traditional ceramics, but are typically more expensive. Additionally, advanced ceramics are typically more sensitive to the chemical and physical defects present in the starting raw materials, or those that are introduced during manufacturing.

  2. Oligomerization process

    DOE Patents [OSTI]

    Smith, Jr., Lawrence A. (Bellaire, TX); hearn, Dennis (Houston, TX); Jones, Jr., Edward M. (Friendswood, TX)

    1991-01-01

    A liquid phase process for oligomerization of C.sub.4 and C.sub.5 isoolefins or the etherification thereof with C.sub.1 to C.sub.6 alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300.degree. F. wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled.

  3. Etherification process

    DOE Patents [OSTI]

    Smith, Jr., Lawrence A. (Houston, TX); Hearn, Dennis (Houston, TX); Jones, Jr., Edward M. (Friendswood, TX)

    1990-01-01

    A liquid phase process for oligomerization of C.sub.4 and C.sub.5 isoolefins or the etherification thereof with C.sub.1 to C.sub.6 alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120.degree. to 300.degree. F. wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled.

  4. Crystallization process

    SciTech Connect (OSTI)

    Adler, Robert J.; Brown, William R.; Auyang, Lun; Liu, Yin-Chang; Cook, W. Jeffrey

    1986-01-01

    An improved crystallization process is disclosed for separating a crystallizable material and an excluded material which is at least partially excluded from the solid phase of the crystallizable material obtained upon freezing a liquid phase of the materials. The solid phase is more dense than the liquid phase, and it is separated therefrom by relative movement with the formation of a packed bed of solid phase. The packed bed is continuously formed adjacent its lower end and passed from the liquid phase into a countercurrent flow of backwash liquid. The packed bed extends through the level of the backwash liquid to provide a drained bed of solid phase adjacent its upper end which is melted by a condensing vapor.

  5. WELDING PROCESS

    DOE Patents [OSTI]

    Zambrow, J.; Hausner, H.

    1957-09-24

    A method of joining metal parts for the preparation of relatively long, thin fuel element cores of uranium or alloys thereof for nuclear reactors is described. The process includes the steps of cleaning the surfaces to be jointed, placing the sunfaces together, and providing between and in contact with them, a layer of a compound in finely divided form that is decomposable to metal by heat. The fuel element members are then heated at the contact zone and maintained under pressure during the heating to decompose the compound to metal and sinter the members and reduced metal together producing a weld. The preferred class of decomposable compounds are the metal hydrides such as uranium hydride, which release hydrogen thus providing a reducing atmosphere in the vicinity of the welding operation.

  6. Etherification process

    DOE Patents [OSTI]

    Smith, L.A. Jr.; Hearn, D.; Jones, E.M. Jr.

    1990-08-21

    A liquid phase process is described for oligomerization of C[sub 4] and C[sub 5] isoolefins or the etherification thereof with C[sub 1] to C[sub 6] alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300 F wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled. 2 figs.

  7. Oligomerization process

    DOE Patents [OSTI]

    Smith, L.A. Jr.; Hearn, D.; Jones, E.M. Jr.

    1991-03-26

    A liquid phase process is described for oligomerization of C[sub 4] and C[sub 5] isoolefins or the etherification thereof with C[sub 1] to C[sub 6] alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300 F wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled. 2 figures.

  8. D-Zero Central Calorimeter Pressure Vessel and Vacuum Vessel Safety Notes

    SciTech Connect (OSTI)

    Rucinski, R.; Luther, R.; /Fermilab

    1990-10-25

    The relief valve and relief piping capacity was calculated to be 908 sefm air. This exceeds all relieving conditions. The vessel also has a rupture disc with a 2640 scfm air stamped capacity. In order to significantly decrease the amount of time required to fill the cryostats, it is desired to raise the setpoint of the 'operating' relief valve on the argon storage dewar to 20 psig from its existing 16 psig setting. This additional pressure increases the flow to the cryostats and will overwhelm the relief capacity if the temperature of the modules within these vessels is warm enough. Using some conservative assumptions and simple calculations within this note, the maximum average temperature that the modules within each cryostat can be at prior to filling from the storage dewar with liquid argon is at least 290 K. The average temperature of the module mass for any of the three cryostats can be as high as 290 K prior to filling that particular cryostat. This should not be confused with the average temperature of a single type or location which is useful in protecting the modules-not necessarily the vessel itself. A few modules of each type and at different elevations should be used in an average which would account for the different weights of each module. Note that at 290 K, the actual flow of argon through the relief valve and the rupture disk was under the maximum theoretical flows for each relief device. This means that the bulk temperature could actually have been raised to flow argon through the reliefs at their maximum capacity. Therefore, the temperature of 290 K is a conservative value for the calculated flow rate of 12.3 gpm. Safeguards in addition to and used in conjunction with operating procedures shall be implemented in such a way so that the above temperature limitation is not exceeded and such that it is exclusive of the programmable logic controller (PLC). One suggestion is using a toggle switch for each cryostat mounted in the PLC I/O box which

  9. ARM - VAP Process - qmemwrcol

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsqmemwrcol Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Comparison of Water in the Column from MWR vs. Instrument Model (QMEMWRCOL) Note:qmemwrcol is currently inactive and/or retired. Active Dates 1993.10.11 - 2004.06.22 Instrument Categories Derived Quantities and Models, Radiometric The first Quality Measurement Experiment

  10. ARM - VAP Process - sondecalc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productssondecalc Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Balloon-borne sounding system (BBSS): recalculated wind/pressure/temp/RH (SONDECALC) Note:sondecalc is currently inactive and/or retired. Active Dates 1994.04.07 - 1994.05.31 Instrument Categories Atmospheric Profiling Output Products sondenogcptucalc : Balloon-borne Sounding

  11. ARM - VAP Process - toacess

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productstoacess Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Top of atmosphere (TOA): radiative flux data, after R. Cess (TOACESS) Note:toacess is currently inactive and/or retired. Active Dates 1994.08.08 - 1994.12.11 Instrument Categories Other Output Products 1toacess : Top of atmosphere (TOA): radiative flux data, 1-min, after R.

  12. Corrective Measures Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Corrective Measures Process Corrective Measures Process We follow a stringent corrective measures process for legacy cleanup. August 1, 2013 Corrective measures process Corrective measures process

  13. Technical Note: Modeling a complex micro-multileaf collimator using the standard BEAMnrc distribution

    SciTech Connect (OSTI)

    Kairn, T.; Kenny, J.; Crowe, S. B.; Fielding, A. L.; Franich, R. D.; Johnston, P. N.; Knight, R. T.; Langton, C. M.; Schlect, D.; Trapp, J. V.

    2010-04-15

    Purpose: The component modules in the standard BEAMnrc distribution may appear to be insufficient to model micro-multileaf collimators that have trifaceted leaf ends and complex leaf profiles. This note indicates, however, that accurate Monte Carlo simulations of radiotherapy beams defined by a complex collimation device can be completed using BEAMnrc's standard VARMLC component module. Methods: That this simple collimator model can produce spatially and dosimetrically accurate microcollimated fields is illustrated using comparisons with ion chamber and film measurements of the dose deposited by square and irregular fields incident on planar, homogeneous water phantoms. Results: Monte Carlo dose calculations for on-axis and off-axis fields are shown to produce good agreement with experimental values, even on close examination of the penumbrae. Conclusions: The use of a VARMLC model of the micro-multileaf collimator, along with a commissioned model of the associated linear accelerator, is therefore recommended as an alternative to the development or use of in-house or third-party component modules for simulating stereotactic radiotherapy and radiosurgery treatments. Simulation parameters for the VARMLC model are provided which should allow other researchers to adapt and use this model to study clinical stereotactic radiotherapy treatments.

  14. Calculation notes that support accident scenario and consequence of the in-tank fuel fire/deflageration

    SciTech Connect (OSTI)

    Crowe, R.D., Westinghouse Hanford

    1996-09-09

    The purpose of this calculation note is to provide the basis for In-Tank Fuel fire/Deflageration consequence for the Tank Farm Safety Analysis Report (FSAR). Tank Fuel Fire/Deflageration scenario is developed and details and description of the analysis methods are provided.

  15. Calculation notes that support accident scenario and consequence of the in-tank fuel fire/deflagration

    SciTech Connect (OSTI)

    Crowe, R.D.

    1996-09-27

    The purpose of this calculation note is to provide the basis for In-Tank Fuel Fire/Deflageration consequence for the Tank Farm Safety Analysis Report (FSAR). Tank Fuel Fire/Deflageration scenario is developed and details and description of the analysis methods are provided.

  16. COLLOQUIUM - NOTE SPECIAL TIME OF 3:15PM: Savannah River National...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OF 3:15PM: Savannah River National Laboratory: Underpinning Critical National Missions Dr. ... Laboratory has developed the processes to successfully accomplish the site's missions. ...

  17. DME-to-oxygenates process studies

    SciTech Connect (OSTI)

    Tartamella, T.L.; Sardesai, A.; Lee, S.; Kulik, C.J.

    1994-12-31

    The feasibility of the production of hydrocarbons from dimethyl ether (DNM) has been illustrated in a fixed bed micro-reactor as well as a bench scale fluidized bed reactor by the University of Akron/EPRI DME-to-Hydrocarbon (DTG) Process. The DTG process has distinct advantages over its methanol based counterpart. Specifically, the DTG process excels in the area of higher productivity, higher per-pass conversion, and lower heat duties than the MTG process. Also of special importance is the production of oxygenates -- including MTBE, ETBE, and TAME. DME may be reacted with isobutylene to produce a mixture of MTBE and ETBE. The properties of ETBE excel over MTBE in the areas of lower RVP and higher RON. According to industrial reports, MTBE is the fastest growing chemical (1992 US capacity 135,350 BPD, with expected growth of 34%/year to 1997). Also, recent renewed interest as an octane-enhancer and as a source of oxygen has spurred a growing interest in nonrefinery synthesis routes to ETBE. TAME, with its lower RVP and higher RON has proven useful as a gasoline blending agent and octane enhancer and may also be produced directly from DME. DME, therefore, serves as a valuable feedstock in the conversion of may oxygenates with wide-scale industrial importance. It should be also noted that the interest in the utilization of DME as process feedstock is based on the favorable process economics of EPRI/UA`s liquid phase DME process.

  18. Corrective Measures Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Corrective Measures Process Corrective Measures Process We follow a stringent corrective measures process for legacy cleanup. August 1, 2013 Corrective measures process Corrective...

  19. U.S. Downstream Charge Capacity of Operable Petroleum Refineries

    U.S. Energy Information Administration (EIA) Indexed Site

    Day, Except Where Noted) Area: U.S. PAD District 1 Delaware Florida Georgia Maryland New Jersey New York North Carolina Pennsylvania Virginia West Virginia PAD District 2 Illinois Indiana Kansas Kentucky Michigan Minnesota Missouri Nebraska North Dakota Ohio Oklahoma Tennessee Wisconsin PAD District 3 Alabama Arkansas Louisiana Mississippi New Mexico Texas PAD District 4 Colorado Montana Utah Wyoming PAD District 5 Alaska Arizona California Hawaii Nevada Oregon Washington Guam Puerto Rico Virgin

  20. U.S. Production Capacity of Operable Petroleum Refineries

    U.S. Energy Information Administration (EIA) Indexed Site

    Day, Except Where Noted) Area: U.S. PAD District 1 Delaware Florida Georgia Maryland New Jersey New York North Carolina Pennsylvania Virginia West Virginia PAD District 2 Illinois Indiana Kansas Kentucky Michigan Minnesota Missouri Nebraska North Dakota Ohio Oklahoma Tennessee Wisconsin PAD District 3 Alabama Arkansas Louisiana Mississippi New Mexico Texas PAD District 4 Colorado Montana Utah Wyoming PAD District 5 Alaska Arizona California Hawaii Nevada Oregon Washington Guam Puerto Rico Virgin

  1. Sample Memorandum to Reactivate a Directive Placed on Hold (NOTE: Per Office of Executive Secretariat procedures, please use

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sample Memorandum to Reactivate a Directive Placed on Hold (NOTE: Per Office of Executive Secretariat procedures, please use Calibri, 12 point font for this memorandum.) (Effective April 2014) MEMORANDUM FOR: XXXXXXXXXXXXXXXX ASSOCIATE ADMINISTRATOR FOR MANAGEMENT AND BUDGET THROUGH: INGRID KOLB DIRECTOR, OFFICE OF MANAGEMENT FROM: XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX SUBJECT: Request to Reactivate Directive Currently on Hold PURPOSE: The purpose of this memorandum is to request the Directives

  2. Some notes on the calculation of energy-angle correlated distributions with TNG and their representation in File 6 formats

    SciTech Connect (OSTI)

    Larson, D.C.; Fu, C.Y.; Hetrick, D.M.

    1987-01-01

    The model code TNG has been extensively used in evaluation work of structural materials for ENDF/B-VI performed at Oak Ridge National Laboratory. A new aspect of ENDF/B-VI is the use of File 6 formats for energy-angle correlated data. Such data are generally calculated, anchored by experimental data. In this informal note we outline how the TNG results are calculated and entered in the File 6 formats. 4 refs.

  3. Summary Notes from 22 July 2008 Generic Technical Issue Discussion on Long-Term Engineered Cap Performance

    Office of Environmental Management (EM)

    6 Summary Notes from 22 July 2008 Generic Technical Issue Discussion on Long-Term Engineered Cap Performance Attendees: Representatives from the U.S. Department of Energy (DOE)-Headquarters and the U.S. Nuclear Regulatory Commission (NRC) staff met at the DOE offices in Germantown, Maryland on 22 July 2008. Representatives from South Carolina Department of Health and Environmental Control, DOE-Savannah River, and DOE- Office of River Protection participated in the meeting via a teleconference

  4. Natural Gas Processed

    U.S. Energy Information Administration (EIA) Indexed Site

    Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Data Series Area 2009 2010 2011 2012 2013 2014 View History U.S. 15,904,517 16,267,757 16,566,883 17,538,026 17,884,427 19,754,802 1967-2014 Alabama 248,232 242,444 230,546 87,269 89,258 80,590 1969-2014 Alabama Onshore-Alabama 100,491 33,921 35,487 31,116 2011-2014 Alabama Offshore-Alabama 53,348 53,771 49,474 2012-2014 Alaska 2,830,034 2,731,803 2,721,396

  5. ARM - VAP Process - abrfc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsabrfc Documentation & Plots abrfc : XDC documentation Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Arkansas-Red Basin River Forecast Center (ABRFC) Instrument Categories Surface Meteorology General Overview Every hour a gridded (4 km x 4 km) precipitation field is created. This field is a combination of both WSR-88D Nexrad radar precipitation

  6. ARM - VAP Process - aeriprof

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsaeriprof Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : AERI Profiles of Water Vapor and Temperature (AERIPROF) Instrument Categories Derived Quantities and Models, Radiometric AERI profiles of water vapor and temperature are retrieved about every 8 minutes and supplement other methods of determining the structure

  7. ARM - VAP Process - aerosolbe

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsaerosolbe Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Aerosol Best Estimate (AEROSOLBE) Instrument Categories Aerosols Quicklook plots of monthly time series are generated for column AOD, vertical profiles up to 4 km of SSA and g, and for the corresponding RH profile. The optical properties are shown for the

  8. ARM - VAP Process - aip

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsaip Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Aerosol Intensive Properties (AIP) Instrument Categories Aerosols The aip1ogren value-added product (VAP) computes several aerosol intensive properties. It requires as input calibrated, corrected, aerosol extensive properties from the Aerosol Observing Station (AOS). Aerosol

  9. ARM - VAP Process - aod

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsaod Documentation & Plots Technical Report (1) Technical Report (2) Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Aerosol Optical Depth, derived from atmospheric extinction of solar irradiance (AOD) Instrument Categories Derived Quantities and Models, Aerosols The core purpose of the ARM Facility is to reduce uncertainties in climate model predictions.

  10. ARM - VAP Process - aosccnavg

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsaosccnavg Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Aerosol Observing System (AOS): cloud condensation nuclei data, averaged (AOSCCNAVG) Instrument Categories Aerosols This value-added product was developed to consolidate the relevant cloud condensation nuclei (CCN) parameters into a single file and averaged

  11. ARM - VAP Process - armbe

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsarmbe Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : ARM Best Estimate Data Products (ARMBE) Instrument Categories Surface/Subsurface Properties, Satellite Observations, Radiometric, Atmospheric Profiling, Cloud Properties The ARM Best Estimate data products are ARM datastreams specifically tailored to climate modelers for use in

  12. ARM - VAP Process - armbestns

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsarmbestns Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Station-based Surface Products (ARMBESTNS) Instrument Categories Radiometric, Cloud Properties, Surface Meteorology Surface pressure is shown in hPa from different SGP surface meteorological sites (color-coded) from ARMBESTNS data set for the Midlatitude

  13. ARM - VAP Process - baebbr

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsbaebbr Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Best-Estimate Fluxes From EBBR Measurements and Bulk Aerodynamics Calculations (BAEBBR) Instrument Categories Derived Quantities and Models The BAEBBR VAP calculates the bulk aerodynamic latent and sensible heat fluxes from Energy Balance Bowen Ratio (EBBR) Station

  14. ARM - VAP Process - ccnprof

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsccnprof Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Cloud Condensation Nuclei Profile (CCNPROF) Instrument Categories Derived Quantities and Models, Aerosols The cloud condensation nuclei (CCN) concentration at cloud base is the most relevant measure of the aerosol that influences droplet formation in clouds.

  15. ARM - VAP Process - diffcor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsdiffcor Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Correction of Diffuse Shortwave Measurements (DIFFCOR) Instrument Categories Derived Quantities and Models The DIFFCORR1DUTT VAP uses two techniques to correct shortwave (SW) data during daytime hours, using information from a collocated pyrgeometer. First, the

  16. ARM - VAP Process - goeswater

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsgoeswater Documentation & Plots goeswater : XDC documentation Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Water Profiles from GOES Satellite Data (GOESWATER) Instrument Categories Satellite Observations, Atmospheric Profiling General Overview These data are soundings of dew point and temperature over the Southern Great Plains site derived from

  17. ARM - VAP Process - gvrpwv

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsgvrpwv Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : G-Band Vapor Radiometer Precipitable Water Vapor (GVRPWV) Instrument Categories Radiometric The G-Band Vapor Radiometer Precipitable Water Vapor (GVRPWV) value-added product (VAP) computes precipitable water vapor using neural network techniques from data

  18. ARM - VAP Process - interpsonde

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsinterpsonde Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Interpolated Sonde (INTERPSONDE) Instrument Categories Atmospheric Profiling, Derived Quantities and Models Plot for Merged Sounding VAP The INTERPSONDE value-added product (VAP) is a modification of the MERGESONDE VAP that produces a daily file of

  19. ARM - VAP Process - kazrcor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productskazrcor Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : KAZR Corrected Data (KAZRCOR) Instrument Categories Cloud Properties Output Products kazrcorge : Ka ARM Zenith Radar (KAZR): general mode Corrected kazrcorhi : Ka ARM Zenith Radar (KAZR): highest sensitivity mode Corrected kazrcormd : Ka ARM Zenith Radar (KAZR): moderate

  20. ARM - VAP Process - lssonde

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productslssonde Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Microwave Radiometer-Scaled Sonde Profiles (LSSONDE) Instrument Categories Derived Quantities and Models During the Quality Measurement Experiment, a detailed analysis of the output from the AERI Line-by-Line Radiative Transfer Model (LBLRTM) indicated that the error between

  1. ARM - VAP Process - mergesonde

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsmergesonde Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Merged Sounding (MERGESONDE) Instrument Categories Atmospheric Profiling Plot for Merged Sounding VAP The Merged Sounding value-added product uses a combination of observations from radiosonde soundings, microwave radiometers, surface meteorological

  2. ARM - VAP Process - mfrsrcldod

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsmfrsrcldod Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Cloud Optical Properties from MFRSR Using Min Algorithm (MFRSRCLDOD) Instrument Categories Aerosols, Radiometric The mfrsrcldod1min value-added product produces cloud optical depth for overcast liquid clouds using narrowband irradiance measurements from the

  3. ARM - VAP Process - mplavg

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsmplavg Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : MPL: data averaged to fixed 30 second interval, e.g. for polarized data (MPLAVG) Instrument Categories Cloud Properties Output Products mplpolavg : Micropulse Lidar polarized (MPLPOL) data averaged to fixed 30 second interval Primary Measurements The following measurements are

  4. ARM - VAP Process - mplcbh

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsmplcbh Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Cloud Base Height from MPL Using Scott-Spinhirne Algorithm (MPLCBH) Instrument Categories Cloud Properties Output Products mplcbh1scott : MPL: cloud base heights using the Scott/Spinhirne algorithm Primary Measurements The following measurements are those considered

  5. ARM - VAP Process - mplcmask

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsmplcmask Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Cloud mask from Micropulse Lidar (MPLCMASK) Instrument Categories Cloud Properties Sample plot generated by MPLCMASK. Click to enlarge the image. Sample plot generated by MPLCMASK. Click to enlarge the image. An operational cloud boundary algorithm has been

  6. ARM - VAP Process - mplnor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsmplnor Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Normalized Backscatter Profiles from the Micropulse Lidar (MPLNOR) Instrument Categories Cloud Properties This VAP has two primary purposes: to apply the appropriate corrections to create normalized backscatter profiles from the MPL, and to detect all significant cloud

  7. ARM - VAP Process - oacomp

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsoacomp Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Organic Aerosol Component (OACOMP) Instrument Categories Aerosols Both the aerosol mass spectrometer (AMS) and aerosol chemical speciation monitor (ACSM) routinely report the concentrations of inorganic species and total organic matter. Significantly improved

  8. ARM - VAP Process - pblht

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productspblht Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Planetary Boundary Layer Height (PBLHT) Instrument Categories Atmospheric Profiling Quicklook plot showing all PBL height estimates produced by the PBLHT VAP for the 05:30 UTC, April 10, 2004, radiosonde at the Southern Great Plains (SGP) site. Quicklook plot

  9. ARM - VAP Process - qcecor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsqcecor Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Quality Controlled Eddy Correlation Flux Measurement (QCECOR) Instrument Categories Surface/Subsurface Properties Eddy correlation flux measurement systems (ECOR) are used by ARM to provide surface turbulence flux measurements. With the help of the Recovery Act, ARM has

  10. ARM - VAP Process - qmeaerilbl

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsqmeaerilbl Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Comparison of Statistics or Clouds data from AERI vs. LBLRTM Model runs (QMEAERILBL) Instrument Categories Radiometric, Derived Quantities and Models \'typical\' channel 1 observed - calculated residuals \'typical\' channel 1 observed - calculated residuals The observed

  11. ARM - VAP Process - qmelwflux

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsqmelwflux Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Comparison of Longwave Flux Data from AERI and LBLRTM vs. pyrgeometer (QMELWFLUX) Instrument Categories Derived Quantities and Models, Radiometric Output Products qmelwflux : QME: longwave Flux, between AERI, LBLRTM, RRTM, and the pyrgeometer Locations Southern Great Plains

  12. ARM - VAP Process - rap

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsrap Documentation & Plots rap : XDC documentation Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Rapid Refresh Model Data (RAP) Instrument Categories Derived Quantities and Models Primary Measurements The following measurements are those considered scientifically relevant. Atmospheric moisture Atmospheric pressure Atmospheric temperature Cloud base

  13. ARM - VAP Process - ripbe

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsripbe Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Radiatively Important Parameters Best Estimate (RIPBE) Instrument Categories Radiometric, Aerosols, Cloud Properties Quicklook plot showing RIPBE liquid cloud effective radius (top) and quality control flags (bottom). For the first half of the day, no cloud data

  14. ARM - VAP Process - rlprof

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsrlprof Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Raman LIDAR Vertical Profiles (RLPROF) Instrument Categories Atmospheric Profiling, Aerosols, Derived Quantities and Models Rlprof data flow diagram Data flowchart for the RLPROF family. (Larger image available.) The Raman lidar automatically attempts to

  15. ARM - VAP Process - sashelangley

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productssashelangley Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Solar Array Spectrometer (Hemispheric) Langley Regressions (SASHELANGLEY) Instrument Categories Radiometric Contact(s) Brian Ermold Pacific Northwest National Laboratory Developer (509) 375-2277 brian.ermold@pnnl.gov Connor Flynn Pacific Northwest National Laboratory

  16. ARM - VAP Process - sfccldgrid

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productssfccldgrid Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Surface Cloud Grid (SFCCLDGRID) Instrument Categories Cloud Properties, Derived Quantities and Models The Surface Cloud Grid VAP uses as input the 15-minute output from the Shortwave Flux Analysis VAP (Long, 2001; Long and Ackerman, 2000; Long et al., 1999)

  17. ARM - VAP Process - sondeadjust

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productssondeadjust Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Sonde Adjust (SONDEADJUST) Instrument Categories Atmospheric Profiling The sonde-adjust VAP produces data that corrects documented biases in radiosonde humidity measurements. Unique fields contained within this datastream include smoothed original relative

  18. ARM - VAP Process - ssmi

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsssmi Documentation & Plots ssmi : XDC documentation Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Special Sensor Microwave/Imager (SSMI) Instrument Categories Satellite Observations Output Products ssmi10 : Special Sensor Microwave/Imager (SSM/I): Satellite 10 ssmi11 : Special Sensor Microwave/Imager (SSM/I): Satellite 11 ssmi13 : Special Sensor

  19. ARM - VAP Process - surfspecalb

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productssurfspecalb Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Surface Spectral Albedo (SURFSPECALB) Instrument Categories Surface/Subsurface Properties Example quicklook from the SURFSPECALB VAP. The plot shows the estimated spectral albedo at SGP for the 10-m and 25-m towers on September 11, 2004. On this day, the

  20. ARM - VAP Process - swfluxanal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsswfluxanal Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Shortwave Flux Analysis (SWFLUXANAL) Instrument Categories Radiometric, Cloud Properties The SW (shortwave) Flux Analysis VAP applies a clear-sky detection and fitting technique (Long and Ackerman 2000) to data from broadband SW radiometers located at the

  1. ARM - VAP Process - tdmadap

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productstdmadap Documentation & Plots tdmadap : XDC documentation Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Aerosol Properties derived from TDMA Measurements (TDMADAP) Instrument Categories Aerosols Output Products tdmaccncoll : Tandem Differential Mobility Analyzer: Cloud Condensation Nuclei -- D. Collins Primary Measurements The following measurements

  2. Well Placement Decision Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Well Placement Decision Process Well Placement Decision Process Determining where to place a well is a multi-step process. August 1, 2013 Investigation process for determining where to place a sentinel well Investigation process for determining where

  3. ARM - Field Campaign - 2007 Cumulus Humilis Aerosol Process Study (CHAPS)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 Cumulus Humilis Aerosol Process Study (CHAPS) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : 2007 Cumulus Humilis Aerosol Process Study (CHAPS) 2007.06.04 - 2007.06.25 Lead Scientist : Carl Berkowitz For data sets, see below. Abstract The primary goal of this campaign was to characterize and contrast freshly emitted aerosols above, within and below fields of cumulus humilis (or fair-weather cumulus,

  4. ARM - Field Campaign - IPHEX/Orographic Precipitation Processes Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    govCampaignsIPHEX/Orographic Precipitation Processes Study Campaign Links Field Campaign Report IPHEX Web Page ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : IPHEX/Orographic Precipitation Processes Study 2013.12.01 - 2014.12.31 Lead Scientist : Ana Barros For data sets, see below. Abstract IPHEX - Integrated Precipitation and Hydrology Experiment (IPHEX Science Plan, 2013) is a field campaign led by

  5. Extensible packet processing architecture

    DOE Patents [OSTI]

    Robertson, Perry J.; Hamlet, Jason R.; Pierson, Lyndon G.; Olsberg, Ronald R.; Chun, Guy D.

    2013-08-20

    A technique for distributed packet processing includes sequentially passing packets associated with packet flows between a plurality of processing engines along a flow through data bus linking the plurality of processing engines in series. At least one packet within a given packet flow is marked by a given processing engine to signify by the given processing engine to the other processing engines that the given processing engine has claimed the given packet flow for processing. A processing function is applied to each of the packet flows within the processing engines and the processed packets are output on a time-shared, arbitered data bus coupled to the plurality of processing engines.

  6. Upgrading liquid products: Notes from the workshop at the international conference research in thermochemical biomass conversion

    SciTech Connect (OSTI)

    Elliott, D.C.

    1988-07-01

    A workshop was held at the International Energy Agency conference, Research in Thermochemical Biomass Conversion, on the subject of upgrading liquid products. The workshop discussion focused on the two prominent methods of liquids upgrading, catalytic hydroprocessing and catalytic cracking. Catalytic hydroprocessing as applied to biomass liquids relies heavily on petroleum developed technology; similar catalysts and operating conditions are used, although lower space velocities are typical. The need for stabilization of the pyrolytic products prior to hydroprocessing was also discussed. Catalytic cracking of biomass liquids also relies heavily on petroleum processing technology. Zeolite catalyst development has focused on the ZSM-5 of Mobil and its application to pyrolysis products. Significant olefinic gas yields are obtained in the zeolitic processing of biomass pyrolyzates and the conversion of these to liquid fuels is a primary research goal. Aromatic gasoline is the primary product in both catalytic processes. A general conclusion of the workshop participants was that the cost of liquid fuels for internal combustion engines would be higher in the foreseeable future. Due to the high cost of initial biomass liquefaction plants (including upgrading) a more likely near-term product would be aromatic chemicals produced under constrained economic circumstances. 16 refs.

  7. Summary Notes from 28 May 2008 Generic Technical Issue Discussion on Estimating Waste Inventory and Waste Tank Characterization

    Office of Environmental Management (EM)

    8, 2008 Page 1 of 8 Summary Notes from 28 May 2008 Generic Technical Issue Discussion on Estimating Waste Inventory and Waste Tank Characterization Attendees: Representatives from Department of Energy-Headquarters (DOE-HQ) and the U.S. Nuclear Regulatory Commission staff (NRC) met at the DOE offices in Germantown, Maryland on 28 May 2008. Representatives from Department of Energy- Savannah River (DOE-SR), Department of Energy-Richland (DOE-RL), and Department of Energy-River Protection (DOE-ORP)

  8. Note: On-line weak signal detection via adaptive stochastic resonance

    SciTech Connect (OSTI)

    Lu, Siliang; He, Qingbo Kong, Fanrang

    2014-06-15

    We design an instrument with a novel embedded adaptive stochastic resonance (SR) algorithm that consists of a SR module and a digital zero crossing detection module for on-line weak signal detection in digital signal processing applications. The two modules are responsible for noise filtering and adaptive parameter configuration, respectively. The on-line weak signal detection can be stably achieved in seconds. The prototype instrument exhibits an advance of 20 dB averaged signal-to-noise ratio and 5 times averaged adjust R-square as compared to the input noisy signal, in considering different driving frequencies and noise levels.

  9. Note: Electrical detection and quantification of spin rectification effect enabled by shorted microstrip transmission line technique

    SciTech Connect (OSTI)

    Soh, Wee Tee; Ong, C. K.; Peng, Bin; Chai, Guozhi

    2014-02-15

    We describe a shorted microstrip method for the sensitive quantification of Spin Rectification Effect (SRE). SRE for a Permalloy (Ni{sub 80}Fe{sub 20}) thin film strip sputtered onto SiO{sub 2} substrate is demonstrated. Our method obviates the need for simultaneous lithographic patterning of the sample and transmission line, therefore greatly simplifying the SRE measurement process. Such a shorted microstrip method can allow different contributions to SRE (anisotropic magnetoresistance, Hall effect, and anomalous Hall effect) to be simultaneously determined. Furthermore, SRE signals from unpatterned 50 nm thick Permalloy films of area dimensions 5 mm × 10 mm can even be detected.

  10. EEO Complaint Process EEO Complaint Process INFORMAL PROCESS-COUNSELING

    National Nuclear Security Administration (NNSA)

    EEO Complaint Process EEO Complaint Process INFORMAL PROCESS-COUNSELING National Nuclear Security Administration Office of Civil Rights Equal Employment Opportunity: Collaborating For Mission Success EEO POLICY The Department of Energy (DOE) does not discriminate on the basis of age, color, race, disability (physical or mental), national origin, reprisal, religion, sex (including sexual harassment), sexual orientation, genetic information or any other non-merit factor. DOE is committed to equal

  11. Coal liquefaction process with enhanced process solvent

    DOE Patents [OSTI]

    Givens, Edwin N.; Kang, Dohee

    1984-01-01

    In an improved coal liquefaction process, including a critical solvent deashing stage, high value product recovery is improved and enhanced process-derived solvent is provided by recycling second separator underflow in the critical solvent deashing stage to the coal slurry mix, for inclusion in the process solvent pool.

  12. Chapter 6: Innovating Clean Energy Technologies in Advanced Manufacturing | Process Heating Technology Assessment

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Process Heating Chapter 6: Technology Assessments NOTE: This technology assessment is available as an appendix to the 2015 Quadrennial Technology Review (QTR). Process Heating is one of fourteen manufacturing-focused technology assessments prepared in support of Chapter 6: Innovating Clean Energy Technologies in Advanced Manufacturing. For context within the 2015 QTR, key connections between this technology assessment, other QTR technology chapters, and other Chapter 6 technology assessments are

  13. Chapter 6: Innovating Clean Energy Technologies in Advanced Manufacturing | Process Intensification Technology Assessment

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Process Intensification Chapter 6: Technology Assessments NOTE: This technology assessment is available as an appendix to the 2015 Quadrennial Technology Review (QTR). Process Intensification is one of fourteen manufacturing-focused technology assessments prepared in support of Chapter 6: Innovating Clean Energy Technologies in Advanced Manufacturing. For context within the 2015 QTR, key connections between this technology assessment, other QTR technology chapters, and other Chapter 6 technology

  14. Chapter 6: Innovating Clean Energy Technologies in Advanced Manufacturing | Roll-to-Roll Processing Technology Assessment

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Roll to Roll Processing Chapter 6: Technology Assessments NOTE: This technology assessment is available as an appendix to the 2015 Quadrennial Technology Review (QTR). Roll-to-Roll Processing is one of fourteen manufacturing-focused technology assessments prepared in support of Chapter 6: Innovating Clean Energy Technologies in Advanced Manufacturing. For context within the 2015 QTR, key connections between this technology assessment, other QTR technology chapters, and other Chapter 6 technology

  15. ARM - VAP Process - lbl

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productslbl Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Line-By-Line Radiative Transfer Model (LBL) Instrument Categories Radiometric, Atmospheric Profiling The Line-by-Line Radiative Transfer Model (LBLRTM) is a product of Atmospheric and Environmental Research, Incorporated (AER). The LBLRTM is based on the FASCODE line-by-line model,

  16. ARM - VAP Process - mwravg

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsmwravg Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Microwave Radiometer Averages in 1- and 5-Minute Increments (MWRAVG) Instrument Categories Derived Quantities and Models This VAP averages the principal fields from the MWR ( 23.8 GHz sky brightness temperature, 31.4 GHz sky brightness temperature, Total water vapor along LOS

  17. ARM - VAP Process - qcrad

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsqcrad Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Data Quality Assessment for ARM Radiation Data (QCRAD) Instrument Categories Radiometric Data plot of upwelling LW testing versus air temperature. Green and red represent the 1st and 2nd level maximum, while light and dark blue represent the 1st and 2nd level

  18. ARM - VAP Process - radfluxanal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productsradfluxanal Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Radiative Flux Analysis (RADFLUXANAL) Instrument Categories Derived Quantities and Models, Surface Meteorology, Radiometric sgpradflux1longC1.c2_OpPlot1.20140509.000000[1] The Radiative Flux Analysis VAP estimates clear-sky shortwave (SW) and longwave (LW) surface fluxes.

  19. ARM - VAP Process - twrmr

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productstwrmr Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : Tower Water-Vapor Mixing Ratio (TWRMR) Instrument Categories Atmospheric Profiling The primary purpose of this algorithm is to calculate water-vapor mixing ratio at the 25- and 60-m levels of the tower at the Southern Great Plains (SGP) Central Facility. Since

  20. ARM - VAP Process - wacrarscl

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Productswacrarscl Documentation & Plots Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : W-band Cloud Radar Active Remote Sensing of Cloud (WACRARSCL) Instrument Categories Cloud Properties Observations from the 95 GHz W-band ARM Cloud Radar (WACR), Micropulse Lidar, and ceilometer have been combined using the new WACR Active Remote Sensing of Clouds (WACR-ARSCL)

  1. Note: An improved calibration system with phase correction for electronic transformers with digital output

    SciTech Connect (OSTI)

    Cheng, Han-miao Li, Hong-bin

    2015-08-15

    The existing electronic transformer calibration systems employing data acquisition cards cannot satisfy some practical applications, because the calibration systems have phase measurement errors when they work in the mode of receiving external synchronization signals. This paper proposes an improved calibration system scheme with phase correction to improve the phase measurement accuracy. We employ NI PCI-4474 to design a calibration system, and the system has the potential to receive external synchronization signals and reach extremely high accuracy classes. Accuracy verification has been carried out in the China Electric Power Research Institute, and results demonstrate that the system surpasses the accuracy class 0.05. Furthermore, this system has been used to test the harmonics measurement accuracy of all-fiber optical current transformers. In the same process, we have used an existing calibration system, and a comparison of the test results is presented. The system after improvement is suitable for the intended applications.

  2. Disposing of High-Level Radioactive Waste in Germany - A Note from the Licensing Authority - 12530

    SciTech Connect (OSTI)

    Pick, Thomas Stefan; Bluth, Joachim; Lauenstein, Christof; Markhoefer, Joerg

    2012-07-01

    Following the national German consensus on the termination of utilisation of nuclear energy in the summer of 2011, the Federal and Laender Governments have declared their intention to work together on a national consensus on the disposal of radioactive waste as well. Projected in the early 1970's the Federal Government had started exploring the possibility to establish a repository for HLW at the Gorleben site in 1977. However, there is still no repository available in Germany today. The delay results mainly from the national conflict over the suitability of the designated Gorleben site, considerably disrupting German society along the crevice that runs between supporters and opponents of nuclear energy. The Gorleben salt dome is situated in Lower Saxony, the German state that also hosts the infamous Asse mine repository for LLW and ILW and the Konrad repository project designated to receive LLW and ILW as well. With the fourth German project, the Morsleben L/ILW repository only 20 km away across the state border, the state of Lower Saxony carries the main load for the disposal of radioactive waste in Germany. After more than 25 years of exploration and a 10 year moratorium the Gorleben project has now reached a cross-road. Current plans for setting up a new site selection procedure in Germany call for the selection and exploration of up to four alternative sites, depending only on suitable geology. In the meantime the discussion is still open on whether the Gorleben project should be terminated in order to pacify the societal conflict or being kept in the selection process on account of its promising geology. The Lower Saxony Ministry for Environment and Climate Protection proposes to follow a twelve-step-program for finding the appropriate site, including the Gorleben site in the process. With its long history of exploration the site is the benchmark that alternative sites will have to compare with. Following the national consensus of 2011 on the termination of

  3. CNTA_Well_Pad_restoration_ltr.pdf

    Office of Legacy Management (LM)

  4. FC-PAD Organization and Activities

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... electron microscopy (STEM) Atomic resolution imaging Electron Energy ... using electrochemical techniques X-ray absorption spectroscopy for catalyst ...

  5. TABLE27.CHP:Corel VENTURA

    Gasoline and Diesel Fuel Update (EIA)

    Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining Note: Refer to Appendix A for Refining District descriptions. Source: Energy Information...

  6. Technical Note: Measurement of bow tie profiles in CT scanners using radiochromic film

    SciTech Connect (OSTI)

    Whiting, Bruce R.; Dohatcu, Andreea C.; Evans, Joshua D.; Williamson, Jeffrey F.; Politte, David G.

    2015-06-15

    Purpose: To provide a noninvasive technique to measure the intensity profile of the fan beam in a computed tomography (CT) scanner that is cost effective and easily implemented without the need to access proprietary scanner information or service modes. Methods: The fabrication of an inexpensive aperture is described, which is used to expose radiochromic film in a rotating CT gantry. A series of exposures is made, each of which is digitized on a personal computer document scanner, and the resulting data set is analyzed to produce a self-consistent calibration of relative radiation exposure. The bow tie profiles were analyzed to determine the precision of the process and were compared to two other measurement techniques, direct measurements from CT gantry detectors and a dynamic dosimeter. Results: The radiochromic film method presented here can measure radiation exposures with a precision of ∼6% root-mean-square relative error. The intensity profiles have a maximum 25% root-mean-square relative error compared with existing techniques. Conclusions: The proposed radiochromic film method for measuring bow tie profiles is an inexpensive (∼$100 USD + film costs), noninvasive method to measure the fan beam intensity profile in CT scanners.

  7. ADIFOR: Fortran source translation for efficient derivatives. ADIFOR Working Note No. 4

    SciTech Connect (OSTI)

    Bischof, C.; Corliss, G.; Griewank, A.; Hovland, P.; Carle, A.

    1992-07-01

    The numerical methods employed in the solution of many scientific computing problems require the computation of derivatives of a function f: R{sup n} {yields} R{sup m}. Both the accuracy and the computational requirements of the derivative computation are usually of critical importance for the robustness and speed of the numerical method. ADIFOR (Automatic Differentiation In FORtran) is a source translation tool implemented using the data abstractions and program analysis capabilities of the ParaScope Parallel Programming Environment. ADIFOR accepts arbitrary Fortran-77 code defining the computation of a function and writes portable Fortran-77 code for the computation of its derivatives. In contrast to previous approaches, ADIFOR views automatic differentiation as a process of source translation that exploits computational context to reduce the cost of derivative computations. Experimental results show that ADIFOR can handle real-life codes, providing exact derivatives with a running time that is competitive with the standard divided-difference approximations of derivatives and which may perform orders of magnitude faster than divided-differences in cases. The computational scientist using ADIFOR is freed from worrying about the accurate and efficient computation of derivatives, even for complicated ``functions,`` and hence, is able to concentrate on the more important issues of algorithm design or system modeling. 35 refs.

  8. Special parallel processing workshop

    SciTech Connect (OSTI)

    1994-12-01

    This report contains viewgraphs from the Special Parallel Processing Workshop. These viewgraphs deal with topics such as parallel processing performance, message passing, queue structure, and other basic concept detailing with parallel processing.

  9. Desalination processes and performance

    SciTech Connect (OSTI)

    Summers, L. J.

    1995-06-01

    Different desalination processes are evaluated for feed, capacity, performance, energy requirements, and cost. These include distillation, reverse osmosis, or electrodialysis. Detailed information is given on distillation processes and membrane processes.

  10. A rookie's guide to Booster operations. Booster technical note no. 231

    SciTech Connect (OSTI)

    Zeno, K.

    1998-09-29

    The purpose of the Booster is to act as an injector for the AGS. It accelerates both protons and other ions. Proton acceleration is distinguished from the acceleration of other ions for several reasons. First, the experimental physics associated with protons, called High Energy Physics is different than that associated with other Ions, called Heavy Ion Physics. From the machine perspective, the process of injection of so called Heavy Ions (ions which are not protons), is distinctly different, from that of protons. A different preinjector, or injector for the Booster, is used for each case. For Protons, a 200 MeV Linear accelerator (The Linac) serves as a preinjector; for Heavy Ions, the Tandem Van De Graaf (The Tandem) is the preinjector. An attribute of the circulating beam which determines to a large degree what problems and what type of machine setup is involved is the beam intensity. The author's focus in this guide is on trying to convey the knowledge and experience involved in the operation of the Booster. Many of the problems encountered can be traced back to equipment failures, often power supplies. Although diagnostics are used, there can also be issues with the controls system itself. Problems with the controls system and prevent fixing or even finding a problem with a machine. The issue of improving a machines' performance can often involve trial and error and observations. The hard part is finding the relationships between things in the day to day operation of the machine. Abstractions about physics, information about controls and instrumentation, and purely empirical observations of how the machine behaves are all part of it.

  11. Woody Biomass Harvesting and Processing Tax Credit (Corporate)

    Broader source: Energy.gov [DOE]

    Note: The application period for this program is closed, check the program website for future openings.

  12. Next Generation Manufacturing Processes

    Broader source: Energy.gov [DOE]

    New process technologies can rejuvenate U.S. manufacturing. Novel processing concepts can open pathways to double net energy productivity, enabling rapid manufacture of energy-efficient, high...

  13. Hydropower Process Improvements

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Process Improvements William J. Palmer Hydropower Program Manager South Atlantic Division 2 April 2015 BUILDING STRONG Focus Areas For Process Improvements InspectionsCondition ...

  14. Salt Waste Processing Initiatives

    Office of Environmental Management (EM)

    Patricia Suggs Salt Processing Team Lead Assistant Manager for Waste Disposition Project Office of Environmental Management Savannah River Site Salt Waste Processing Initiatives 2 ...

  15. Thermochemical Processes | Bioenergy | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Processes NREL is developing gasification and pyrolysis processes for the cost effective thermochemical conversion of biomass to biofuels and biofuel intermediaries. In our ...

  16. Biochemical Processes | Bioenergy | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Biochemical Processes NREL is developing biochemical conversion processes to generate sugars and sugars-derived intermediates for upgrading to biofuels and bioproducts. We develop ...

  17. Calculation notes in support of TWRS FSAR spray leak accident analysis

    SciTech Connect (OSTI)

    Hall, B.W.

    1996-09-25

    This document contains the detailed calculations that support the spray leak accident analysis in the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR). The consequence analyses in this document form the basis for the selection of controls to mitigate or prevent spray leaks throughout TWRS. Pressurized spray leaks can occur due to a breach in containment barriers along transfer routes, during waste transfers. Spray leaks are of particular safety concern because, depending on leak dimensions, and waste pressure, they can be relatively efficient generators of dispersible sized aerosols that can transport downwind to onsite and offsite receptors. Waste is transferred between storage tanks and between processing facilities and storage tanks in TWRS through a system of buried transfer lines. Pumps for transferring waste and jumpers and valves for rerouting waste are located inside below grade pits and structures that are normally covered. Pressurized spray leaks can emanate to the atmosphere due to breaches in waste transfer associated equipment inside these structures should the structures be uncovered at the time of the leak. Pressurized spray leaks can develop through holes or cracks in transfer piping, valve bodies or pump casings caused by such mechanisms as corrosion, erosion, thermal stress, or water hammer. Leaks through degraded valve packing, jumper gaskets, or pump seals can also result in pressurized spray releases. Mechanisms that can degrade seals, packing and gaskets include aging, radiation hardening, thermal stress, etc. An1782other common cause for spray leaks inside transfer enclosures are misaligned jumpers caused by human error. A spray leak inside a DST valve pit during a transfer of aging waste was selected as the bounding, representative accident for detailed analysis. Sections 2 through 5 below develop this representative accident using the DOE- STD-3009 format. Sections 2 describes the unmitigated and mitigated accident

  18. Idaho Chemical Processing Plant Process Efficiency improvements

    SciTech Connect (OSTI)

    Griebenow, B.

    1996-03-01

    In response to decreasing funding levels available to support activities at the Idaho Chemical Processing Plant (ICPP) and a desire to be cost competitive, the Department of Energy Idaho Operations Office (DOE-ID) and Lockheed Idaho Technologies Company have increased their emphasis on cost-saving measures. The ICPP Effectiveness Improvement Initiative involves many activities to improve cost effectiveness and competitiveness. This report documents the methodology and results of one of those cost cutting measures, the Process Efficiency Improvement Activity. The Process Efficiency Improvement Activity performed a systematic review of major work processes at the ICPP to increase productivity and to identify nonvalue-added requirements. A two-phase approach was selected for the activity to allow for near-term implementation of relatively easy process modifications in the first phase while obtaining long-term continuous improvement in the second phase and beyond. Phase I of the initiative included a concentrated review of processes that had a high potential for cost savings with the intent of realizing savings in Fiscal Year 1996 (FY-96.) Phase II consists of implementing long-term strategies too complex for Phase I implementation and evaluation of processes not targeted for Phase I review. The Phase II effort is targeted for realizing cost savings in FY-97 and beyond.

  19. ARM - Process Configuration Manager

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FormsProcess Configuration Manager Ingest Ingest Workflow Graphic Supporting Workflow Documentation Supporting Tools and Forms Process Configuration Manager (PCM) Metadata Management Tool (MMT) ARM Data Integrator (ADI) Ingest Readiness Form Associated Status Reports Contacts Engineering Processes Engineering Home Workflow Graphic Engineering Workflow Document Tools for Workflow ECR ECO BCR Ingests Value-Added Products Reprocessing Instruments Data System Elements Field Campaign Startup Process

  20. Working testing process

    SciTech Connect (OSTI)

    Sparkman, D.

    1997-11-01

    This report contains viewgraphs on the process of testing security and intrusion detection software.

  1. U.S. Natural Gas Plant Processing

    Gasoline and Diesel Fuel Update (EIA)

    Area: U.S. Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Data Series Area Jan-16 Feb-16 Mar-16 Apr-16 May-16 Jun-16 View History NGPL Production, Gaseous Equivalent (Million Cubic Feet) 148,450 139,621 157,047 151,450 160,290 156,305 1973-2016

    Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By:

  2. Advanced Multi-Product Coal Utilization By-Product Processing Plant

    SciTech Connect (OSTI)

    Thomas Robl; John Groppo

    2005-09-01

    The objective of the project is to build a multi-product ash beneficiation plant at Kentucky Utilities 2,200-MW Ghent Generating Station, located in Carroll County, Kentucky. This part of the study includes the examination of the feedstocks for the beneficiation plant. The ash, as produced by the plant, and that stored in the lower pond were examined. A mobile demonstration unit has been designed and constructed for field demonstration. The demonstration unit was hauled to the test site on trailers that were place on a test pad located adjacent to the ash pond and re-assembled. The continuous test unit will be operated at the Ghent site and will evaluate three processing configurations while producing sufficient products to facilitate thorough product testing. The test unit incorporates all of the unit processes that will be used in the commercial design and is self sufficient with respect to water, electricity and processing capabilities. Representative feed ash for the operation of the filed testing unit was excavated from a location within the lower ash pond determined from coring activities. Approximately 150 tons of ash was excavated and pre-screened to remove +3/8 inch material that could cause plugging problems during operation of the demonstration unit.

  3. Image processing applied to laser cladding process

    SciTech Connect (OSTI)

    Meriaudeau, F.; Truchetet, F.

    1996-12-31

    The laser cladding process, which consists of adding a melt powder to a substrate in order to improve or change the behavior of the material against corrosion, fatigue and so on, involves a lot of parameters. In order to perform good tracks some parameters need to be controlled during the process. The authors present here a low cost performance system using two CCD matrix cameras. One camera provides surface temperature measurements while the other gives information relative to the powder distribution or geometric characteristics of the tracks. The surface temperature (thanks to Beer Lambert`s law) enables one to detect variations in the mass feed rate. Using such a system the authors are able to detect fluctuation of 2 to 3g/min in the mass flow rate. The other camera gives them information related to the powder distribution, a simple algorithm applied to the data acquired from the CCD matrix camera allows them to see very weak fluctuations within both gaz flux (carriage or protection gaz). During the process, this camera is also used to perform geometric measurements. The height and the width of the track are obtained in real time and enable the operator to find information related to the process parameters such as the speed processing, the mass flow rate. The authors display the result provided by their system in order to enhance the efficiency of the laser cladding process. The conclusion is dedicated to a summary of the presented works and the expectations for the future.

  4. Waste processing air cleaning

    SciTech Connect (OSTI)

    Kriskovich, J.R.

    1998-07-27

    Waste processing and preparing waste to support waste processing relies heavily on ventilation. Ventilation is used at the Hanford Site on the waste storage tanks to provide confinement, cooling, and removal of flammable gases.

  5. Risk Management Process Overview

    Broader source: Energy.gov [DOE]

    The cybersecurity risk management process explained in the Electricity Sector Cybersecurity Risk Management Process (RMP) Guideline has two primary components: the risk management model and the the risk management cycle.

  6. Gas-separation process

    DOE Patents [OSTI]

    Toy, Lora G.; Pinnau, Ingo; Baker, Richard W.

    1994-01-01

    A process for separating condensable organic components from gas streams. The process makes use of a membrane made from a polymer material that is glassy and that has an unusually high free volume within the polymer material.

  7. Corrective Actions Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Community, Environment » Environmental Stewardship » Environmental Cleanup » Corrective Actions Corrective Actions Process The general process for evaluating and remediating potential release sites is called the corrective action process. Contact Environmental Communication & Public Involvement P.O. Box 1663 MS M996 Los Alamos, NM 87545 (505) 667-0216 Email Corrective actions The Laboratory's corrective actions process refers to the way in which the Laboratory investigates, stabilizes,

  8. Fuel gas conditioning process

    DOE Patents [OSTI]

    Lokhandwala, Kaaeid A.

    2000-01-01

    A process for conditioning natural gas containing C.sub.3+ hydrocarbons and/or acid gas, so that it can be used as combustion fuel to run gas-powered equipment, including compressors, in the gas field or the gas processing plant. Compared with prior art processes, the invention creates lesser quantities of low-pressure gas per unit volume of fuel gas produced. Optionally, the process can also produce an NGL product.

  9. Direct process for explosives

    DOE Patents [OSTI]

    Akst, I.B.; Stinecipher, M.M.

    1982-10-12

    A direct process of making ethylenediamine dinitrate through the reaction of ethylenediamine and ammonium nitrate is described.

  10. Semisolid Metal Processing Consortium

    SciTech Connect (OSTI)

    Apelian,Diran

    2002-01-10

    Mathematical modeling and simulations of semisolid filling processes remains a critical issue in understanding and optimizing the process. Semisolid slurries are non-Newtonian materials that exhibit complex rheological behavior. There the way these slurries flow in cavities is very different from the way liquid in classical casting fills cavities. Actually filling in semisolid processing is often counter intuitive

  11. Innovative Process Technologies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovative Process Technologies Research Team Members Key Contacts Innovative Process Technologies Innovative Process Technologies is concerned with the development of innovative costeffective technologies that promote efficiency, environmental performance, availability of advanced energy systems, and the development of computational tools that shorten development timelines of advanced energy systems. NETL, working with members of the NETL-Regional University Alliance (NETL-RUA), will focus on

  12. Note on gravitational baryogenesis

    SciTech Connect (OSTI)

    Sadjadi, H. Mohseni

    2007-12-15

    The coupling between Ricci scalar curvature and the baryon number current dynamically breaks CPT in an expanding universe and leads to baryon asymmetry. We study the effect of time dependence of the equation of state parameter of the Friedmann-Robertson-Walker universe on this asymmetry.

  13. ALARA notes, Number 8

    SciTech Connect (OSTI)

    Khan, T.A.; Baum, J.W.; Beckman, M.C.

    1993-10-01

    This document contains information dealing with the lessons learned from the experience of nuclear plants. In this issue the authors tried to avoid the `tyranny` of numbers and concentrated on the main lessons learned. Topics include: filtration devices for air pollution abatement, crack repair and inspection, and remote handling equipment.

  14. Meeting Notes and Presentations

    Office of Environmental Management (EM)

    Tele-Conference - February 22, 2010 2 of 2 Approach for Remaining Focus Areas: Robert Murray presented a proposed approach to divide the remaining focus areas into three...

  15. Appendix A Explanatory Notes

    U.S. Energy Information Administration (EIA) Indexed Site

    August 2016 98 U.S. Energy Information Administration | Natural Gas Monthly Dakota, Ohio, Pennsylvania, Utah, and West Virginia) were added to the EIA-914 data collection and are reported individually. The remaining states/areas (Alabama, Arizona, Federal Offshore Pacific, Florida, Illinois, Indiana, Kentucky, Maryland, Michigan, Mississippi, Missouri, Nebraska, Nevada, New York, Oregon, South Dakota, Tennessee, and Virginia) are grouped in the "Other States" category. The sum of

  16. Appendix A Explanatory Notes

    U.S. Energy Information Administration (EIA) Indexed Site

  17. Manhattan Project: Potsdam Note

    Office of Scientific and Technical Information (OSTI)

    Potsdam, July 19, 1945 (Truman wrote the above on the back of this). Click on a link below to return to: Espionage and the Manhattan Project, 1940-1945 Library Potsdam and the ...

  18. Notes and Definitions

    Weekly Natural Gas Storage Report (EIA)

    Oklahoma, and Texas Mountain Region Arizona, Colorado, Idaho, Montana, Nebraska, New Mexico, Nevada, North Dakota, South Dakota, Utah, and Wyoming Pacific Region California,...

  19. ARM - Field Notes Article

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... I truly enjoyed writing about the daily field activities, participants' roles, their instruments, and the scientific issues related to the effects of air pollution on climate ...

  20. Table 2.4 Household Energy Consumption by Census Region, Selected Years, 1978-2009 (Quadrillion Btu, Except as Noted)

    U.S. Energy Information Administration (EIA) Indexed Site

    Household 1 Energy Consumption by Census Region, Selected Years, 1978-2009 (Quadrillion Btu, Except as Noted) Census Region 2 1978 1979 1980 1981 1982 1984 1987 1990 1993 1997 2001 2005 2009 United States Total (does not include wood) 10.56 9.74 9.32 9.29 8.58 9.04 9.13 9.22 10.01 10.25 9.86 10.55 10.18 Natural Gas 5.58 5.31 4.97 5.27 4.74 4.98 4.83 4.86 5.27 5.28 4.84 4.79 4.69 Electricity 3 2.47 2.42 2.48 2.42 2.35 2.48 2.76 3.03 3.28 3.54 3.89 4.35 4.39 Distillate Fuel Oil and Kerosene 2.19

  1. Evaluation of steelmaking processes

    SciTech Connect (OSTI)

    Fruehan, R.J.

    1994-01-01

    Objective of the AISI Direct Steelmaking Program is to develop a process for producing steel directly from ore and coal; the process should be less capital intensive, consume less energy, and have higher productivity. A task force was formed to examine available processes: trough, posthearth, IRSID, Electric Arc Furnace, energy optimizing furnace. It is concluded that there is insufficient incentive to replace a working BOF with any of these processes to refine hot metal; however, if new steelmaking capacity is required, IRSID and EOF should be considered. A fully continuous process should not be considered until direct ironmaking and continuous refining are perfected.

  2. Biomass process handbook

    SciTech Connect (OSTI)

    Not Available

    1983-01-01

    Descriptions are given of 42 processes which use biomass to produce chemical products. Marketing and economic background, process description, flow sheets, costs, major equipment, and availability of technology are given for each of the 42 processes. Some of the chemicals discussed are: ethanol, ethylene, acetaldehyde, butanol, butadiene, acetone, citric acid, gluconates, itaconic acid, lactic acid, xanthan gum, sorbitol, starch polymers, fatty acids, fatty alcohols, glycerol, soap, azelaic acid, perlargonic acid, nylon-11, jojoba oil, furfural, furfural alcohol, tetrahydrofuran, cellulose polymers, products from pulping wastes, and methane. Processes include acid hydrolysis, enzymatic hydrolysis, fermentation, distillation, Purox process, and anaerobic digestion.

  3. Ironmaking Process Alternative Screening Study, Volume 1

    SciTech Connect (OSTI)

    Lockwood Greene, . .

    2005-01-06

    charge and those producing Hot Metal for charge to the EAF. (2) A pronounced sensitivity to Steel Scrap Cost was felt less by the Hot Metal Processes and the Fine Ore Processes that typically do not utilize much purchased scrap. (3) In terms of evolving processes, the Tecnored Process (and in particular, the lower-operating cost process with integral co-generation of electrical power) was in the most favorable groupings at all scrap cost sensitivities. (4) It should be noted also that the Conventional Blast Furnace process utilizing Non-Recovery coke (from a continuous coking process with integral co-generation of electrical power) and the lower-capital cost Mini Blast Furnace also showed favorable Relative Economics for the low and median Scrap Cost sensitivities. (5) The lower-cost, more efficient MauMee Rotary Hearth Process that uses a Briquetted Iron Unit Feed (instead of a dried or indurated iron ore pellet) also was in the most favorable process groupings. Those processes with lower-cost raw materials (i.e. fine ore and/or nonmetallurgical coal as the reductant) had favorable combined economics. In addition, the hot metal processes (in part due to the sensible heat impacts in the EAF and due to their inherently lower costs) also had favorable combined economics.

  4. Source: U.S. Energy Information Administration, Form EIA-63B, 'Annual Photovoltaic Cell/Module Shipments Report' Note: Dollars are not

    U.S. Energy Information Administration (EIA) Indexed Site

    Modules $5,425,417 Total Modules $0.87 Table 2. Value and average value of photovoltaic module shipments, 2014 Module value, total shipments (thousand dollars) Module average value (dollars per peak watt) Source: U.S. Energy Information Administration, Form EIA-63B, 'Annual Photovoltaic Cell/Module Shipments Report' Note: Dollars are not adjusted for inflation.

  5. Microsoft PowerPoint - Final_IIP NOPR PubWorkshop Presentation_NoNotes_3-22-2016

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Interagency Pre-Application (IIP) Process Notice of Proposed Rulemaking Public Workshop Meghan Conklin, Julie Smith, and Lynn Alexander March 22, 2016 2 Agenda * Introduction * Background of Integrated Interagency Pre- application (IIP) Process * Description of Proposed Rule and IIP Process * Next Steps * Questions and Comments on Proposed Rule 3 How to Participate * Chat Panel - Send a message to all panelists * Include your full name and organization * Q&A Panel - Submit your question

  6. Method and apparatus for monitoring plasma processing operations

    DOE Patents [OSTI]

    Smith, Jr., Michael Lane; Stevenson, Joel O'Don; Ward, Pamela Peardon Denise

    2001-01-01

    The invention generally relates to various aspects of a plasma process, and more specifically the monitoring of such plasma processes. One aspect relates in at least some manner to calibrating or initializing a plasma monitoring assembly. This type of calibration may be used to address wavelength shifts, intensity shifts, or both associated with optical emissions data obtained on a plasma process. A calibration light may be directed at a window through which optical emissions data is being obtained to determine the effect, if any, that the inner surface of the window is having on the optical emissions data being obtained therethrough, the operation of the optical emissions data gathering device, or both. Another aspect relates in at least some manner to various types of evaluations which may be undertaken of a plasma process which was run, and more typically one which is currently being run, within the processing chamber. Plasma health evaluations and process identification through optical emissions analysis are included in this aspect. Yet another aspect associated with the present invention relates in at least some manner to the endpoint of a plasma process (e.g., plasma recipe, plasma clean, conditioning wafer operation) or discrete/discernible portion thereof (e.g., a plasma step of a multiple step plasma recipe). A final aspect associated with the present invention relates to how one or more of the above-noted aspects may be implemented into a semiconductor fabrication facility, such as the distribution of wafers to a wafer production system.

  7. Method and apparatus for monitoring plasma processing operations

    DOE Patents [OSTI]

    Smith, Jr., Michael Lane; Stevenson, Joel O'Don; Ward, Pamela Peardon Denise

    2002-07-16

    The invention generally relates to various aspects of a plasma process, and more specifically the monitoring of such plasma processes. One aspect relates in at least some manner to calibrating or initializing a plasma monitoring assembly. This type of calibration may be used to address wavelength shifts, intensity shifts, or both associated with optical emissions data obtained on a plasma process. A calibration light may be directed at a window through which optical emissions data is being obtained to determine the effect, if any, that the inner surface of the window is having on the optical emissions data being obtained therethrough, the operation of the optical emissions data gathering device, or both. Another aspect relates in at least some manner to various types of evaluations which may be undertaken of a plasma process which was run, and more typically one which is currently being run, within the processing chamber. Plasma health evaluations and process identification through optical emissions analysis are included in this aspect. Yet another aspect associated with the present invention relates in at least some manner to the endpoint of a plasma process (e.g., plasma recipe, plasma clean, conditioning wafer operation) or discrete/discernible portion thereof (e.g., a plasma step of a multiple step plasma recipe). A final aspect associated with the present invention relates to how one or more of the above-noted aspects may be implemented into a semiconductor fabrication facility, such as the distribution of wafers to a wafer production system.

  8. Method and apparatus for monitoring plasma processing operations

    DOE Patents [OSTI]

    Smith, Jr., Michael Lane; Stevenson, Joel O'Don; Ward, Pamela Peardon Denise

    2000-01-01

    The invention generally relates to various aspects of a plasma process, and more specifically the monitoring of such plasma processes. One aspect relates in at least some manner to calibrating or initializing a plasma monitoring assembly. This type of calibration may be used to address wavelength shifts, intensity shifts, or both associated with optical emissions data obtained on a plasma process. A calibration light may be directed at a window through which optical emissions data is being obtained to determine the effect, if any, that the inner surface of the window is having on the optical emissions data being obtained therethrough, the operation of the optical emissions data gathering device, or both. Another aspect relates in at least some manner to various types of evaluations which may be undertaken of a plasma process which was run, and more typically one which is currently being run, within the processing chamber. Plasma health evaluations and process identification through optical emissions analysis are included in this aspect. Yet another aspect associated with the present invention relates in at least some manner to the endpoint of a plasma process (e.g., plasma recipe, plasma clean, conditioning wafer operation) or discrete/discernible portion thereof (e.g., a plasma step of a multiple step plasma recipe). A final aspect associated with the present invention relates to how one or more of the above-noted aspects may be implemented into a semiconductor fabrication facility, such as the distribution of wafers to a wafer production system.

  9. Method and apparatus for monitoring plasma processing operations

    DOE Patents [OSTI]

    Smith, Jr., Michael Lane; Stevenson, Joel O'Don; Ward, Pamela Peardon Denise

    2001-01-01

    The invention generally relates to various aspects of a plasma process, and more specifically the monitoring of such plasma processes. One aspect relates in at least some manner to calibrating or initializing a plasma monitoring assembly. This type of calibration may be used to address wavelength shifts, intensity shifts, or both associated with optical emissions data obtained on a plasma process. A calibration light may be directed at a window through which optical emissions data is being obtained to determine the effect, if any, that the inner surface of the window is having on the optical emissions data being obtained therethrough, the operation of the optical emissions data gathering device, or both. Another aspect relates in at least some manner to various types of evaluations which may be undertaken of a plasma process which was run, and more typically one which is currently being run, within the processing chamber. Plasma health evaluations and process identification through optical emissions analysis are included in this aspect. Yet another aspect associated with the present invention relates in at least some manner to the endpoint of a plasma process (e.g., plasma recipe, plasma clean, conditioning wafer operation) or discrete/discemible portion thereof (e.g., a plasma step of a multiple step plasma recipe). A final aspect associated with the present invention relates to how one or more of the above-noted aspects may be implemented into a semiconductor fabrication facility, such as the distribution of wafers to a wafer production system.

  10. Future Steelmaking Processes

    SciTech Connect (OSTI)

    Prof. R. J. Fruehan

    2004-09-20

    There is an increasing demand for an ironmaking process with lower capital cost, energy consumption and emissions than a blast furnace. It is the hypothesis of the present work that an optimized combination of two reasonable proven technologies will greatly enhance the overall process. An example is a rotary hearth furnace (RHF) linked to a smelter (e.g., AISI, HIsmelt). The objective of this research is to select promising process combinations, develop energy, materials balance and productivity models for the individual processes, conduct a limited amount of basic research on the processes and evaluate the process combinations. Three process combinations were selected with input from the industrial partners. The energy-materials and productivity models for the RHF, smelter, submerged arc furnace and CIRCOFER were developed. Since utilization of volatiles in coal is critical for energy and CO{sub 2} emission reduction, basic research on this topic was also conducted. The process models developed are a major product developed in this research. These models can be used for process evaluation by the industry. The process combinations of an RHF-Smelter and a simplified CIRCOFER-Smelter appear to be promising. Energy consumption is reduced and productivity increased. Work on this project is continuing using funds from other sources.

  11. Petroleum processing handbook

    SciTech Connect (OSTI)

    McKetta, J.J. )

    1992-01-01

    It is time that many of the petroleum processes currently in use be presented in a well-organized, easy-to-read and understandable manner. This handbook fulfills this need by covering up-to-date processing operations. Each chapter is written by a world expert in that particular area, in such a manner that it is easily understood and applied. The handbook is conveniently divided into four sections: products, refining, manufacturing processes, and treating processes. Each of the processing chapters contain information on plant design as well as significant chemical reactions. Wherever possible, shortcut methods of calculations are included along with nomographic methods of solution. In the front of the book are two convenient sections that will be very helpful to the reader. These are (1) conversion to and from SI units, and (2) cost indexes that will enable the reader to update any cost information. Sections have been processed separately for inclusion on the data base.

  12. Graduate Program Selection Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Selection Process Graduate Program Selection Process Point your career towards Los Alamos Lab: work with the best minds on the planet in an inclusive environment that is rich in intellectual vitality and opportunities for growth. Contact Student Programs (505) 665-0987 Email The student hiring process Thank you for your interest in Los Alamos National Laboratory's Student Programs. Once an application is submitted online, it is available for all interested Laboratory hiring officials to view.

  13. Process for LPG recovery

    SciTech Connect (OSTI)

    Khan, Sh. A.; Haliburton, J.

    1985-03-26

    An improved process is described for the separation and recovery of substantially all the propane and heavier hydrocarbon components in a hydrocarbon gaseous feedstream. In this process, the vapor stream from a deethanizer is cooled to liquefaction and contacted with a vapor phase from the hydrocarbon gaseous feedstream. The contact takes place within a direct heat exchanger, and the resulting vapor fraction, which is essentially ethane and methane, is the gaseous product of the process.

  14. Colorado, Processing Sites

    Office of Legacy Management (LM)

    Old and New Rifle, Colorado, Processing Sites September 2014 LMS/RFO-RFN/S11940 This page intentionally left blank LMS/RFO-RFN/S11940 2014 Verification Monitoring Report for the Old and New Rifle, Colorado, Processing Sites September 2014 This page intentionally left blank U.S. Department of Energy 2014 Verification Monitoring Report for the Old and New Rifle, Colorado, Processing Sites September 2014 Doc. No. S11940 Page i Contents Abbreviations

  15. Undergraduate Program Selection Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Selection Process Undergraduate Program Selection Process Point your career towards Los Alamos Lab: work with the best minds on the planet in an inclusive environment that is rich in intellectual vitality and opportunities for growth. Contact Student Programs (505) 665-0987 Email Student hiring process Once an application is submitted online, it is made available for all interested Laboratory hiring officials to view. Hiring officials are Laboratory employees who have the funding and work

  16. TEP process flow diagram

    SciTech Connect (OSTI)

    Wilms, R Scott; Carlson, Bryan; Coons, James; Kubic, William

    2008-01-01

    This presentation describes the development of the proposed Process Flow Diagram (PFD) for the Tokamak Exhaust Processing System (TEP) of ITER. A brief review of design efforts leading up to the PFD is followed by a description of the hydrogen-like, air-like, and waterlike processes. Two new design values are described; the mostcommon and most-demanding design values. The proposed PFD is shown to meet specifications under the most-common and mostdemanding design values.

  17. Earth System Processes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    earth system processes Earth System Processes Cosmogenic isotopes are rare isotopes created when a high-energy cosmic ray interacts with the nucleus of an atom, causing cosmic ray spallation. These isotopes are produced within earth materials such as rocks or soil, in Earth's atmosphere, and in extraterrestrial items such as meteorites. By measuring cosmogenic isotopes, scientists are able to gain insight into a range of geological and astronomical processes. Cosmogenic nuclides can provide a

  18. Industrial process surveillance system

    DOE Patents [OSTI]

    Gross, K.C.; Wegerich, S.W.; Singer, R.M.; Mott, J.E.

    1998-06-09

    A system and method are disclosed for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy. 96 figs.

  19. ARM - Engineering Processes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Processes Workflow Graphic Engineering Workflow Document Tools for Workflow ECR ECO BCR Ingests Value-Added Products Reprocessing Instruments Data System Elements Field...

  20. Graduate Program Selection Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and opportunities for growth. Contact Student Programs (505) 665-8899 Email The student hiring process Thank you for your interest in Los Alamos National Laboratory's Student...

  1. Abstract Submission Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Abstract Submission Process Focusing on methods and computational tools used to help sequence, assemble, and finish genomes, including new sequencing technologies. Contact Shannon...

  2. Industrial Process Surveillance System

    DOE Patents [OSTI]

    Gross, Kenneth C.; Wegerich, Stephan W; Singer, Ralph M.; Mott, Jack E.

    2001-01-30

    A system and method for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy.

  3. Industrial process surveillance system

    DOE Patents [OSTI]

    Gross, Kenneth C.; Wegerich, Stephan W.; Singer, Ralph M.; Mott, Jack E.

    1998-01-01

    A system and method for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy.

  4. Methods and Process Stewardship

    Broader source: Energy.gov [DOE]

    The Project Management Coordination Office (PMCO) leads the development of policies, processes and reporting for project and risk management, including Funding Opportunity Announcement (FOA) and...

  5. Energy Process Innovation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    advanced multiphase reactor concepts and designs and performing validation studies. Research includes the areas of hydrodynamics and kinetics as well as reactor and process ...

  6. Living olefin polymerization processes

    DOE Patents [OSTI]

    Schrock, Richard R.; Bauman, Robert

    2006-11-14

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  7. Living olefin polymerization processes

    DOE Patents [OSTI]

    Schrock, Richard R.; Baumann, Robert

    2003-08-26

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  8. Living olefin polymerization processes

    DOE Patents [OSTI]

    Schrock, Richard R. (Winchester, MA); Baumann, Robert (Cambridge, MA)

    1999-01-01

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  9. Undergraduate Program Selection Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for growth. Contact Student Programs (505) 665-8899 Email Student hiring process Once an application is submitted online, it is made available for all interested Laboratory...

  10. Silica Scaling Removal Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Scaling Removal Process Scientists at Los Alamos National Laboratory have developed a novel technology to remove both dissolved and colloidal silica using small gel particles....

  11. Unit Process Library

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... from the combustion of stemwood burned in slash piles DS DF LNG Liquefaction, Construction - 6132013 This process encompasses the construction of a LNG liquefaction facility. ...

  12. Living olefin polymerization processes

    DOE Patents [OSTI]

    Schrock, R.R.; Baumann, R.

    1999-03-30

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  13. NNMCAB Processes and Procedures

    Broader source: Energy.gov [DOE]

    At the January 8, 2014 Committee meeting NNMCAB Staff, Covered the Procedures and Processes that are used in Running the Board.

  14. Chemical process hazards analysis

    SciTech Connect (OSTI)

    1996-02-01

    The Office of Worker Health and Safety (EH-5) under the Assistant Secretary for the Environment, Safety and Health of the US Department (DOE) has published two handbooks for use by DOE contractors managing facilities and processes covered by the Occupational Safety and Health Administration (OSHA) Rule for Process Safety Management of Highly Hazardous Chemicals (29 CFR 1910.119), herein referred to as the PSM Rule. The PSM Rule contains an integrated set of chemical process safety management elements designed to prevent chemical releases that can lead to catastrophic fires, explosions, or toxic exposures. The purpose of the two handbooks, ``Process Safety Management for Highly Hazardous Chemicals`` and ``Chemical Process Hazards Analysis,`` is to facilitate implementation of the provisions of the PSM Rule within the DOE. The purpose of this handbook ``Chemical Process Hazards Analysis,`` is to facilitate, within the DOE, the performance of chemical process hazards analyses (PrHAs) as required under the PSM Rule. It provides basic information for the performance of PrHAs, and should not be considered a complete resource on PrHA methods. Likewise, to determine if a facility is covered by the PSM rule, the reader should refer to the handbook, ``Process Safety Management for Highly Hazardous Chemicals`` (DOE- HDBK-1101-96). Promulgation of the PSM Rule has heightened the awareness of chemical safety management issues within the DOE. This handbook is intended for use by DOE facilities and processes covered by the PSM rule to facilitate contractor implementation of the PrHA element of the PSM Rule. However, contractors whose facilities and processes not covered by the PSM Rule may also use this handbook as a basis for conducting process hazards analyses as part of their good management practices. This handbook explains the minimum requirements for PrHAs outlined in the PSM Rule. Nowhere have requirements been added beyond what is specifically required by the rule.

  15. Process for preparing radiopharmaceuticals

    DOE Patents [OSTI]

    Barak, Morton; Winchell, Harry S.

    1977-01-04

    A process for the preparation of technetium-99m labeled pharmaceuticals is disclosed. The process comprises initially isolating technetium-99m pertechnetate by adsorption upon an adsorbent packing in a chromatographic column. The technetium-99m is then eluted from the packing with a biological compound to form a radiopharmaceutical.

  16. Associative list processing unit

    DOE Patents [OSTI]

    Hemmert, Karl Scott; Underwood, Keith D.

    2013-01-29

    An associative list processing unit and method comprising employing a plurality of prioritized cell blocks and permitting inserts to occur in a single clock cycle if all of the cell blocks are not full. Also, an associative list processing unit and method comprising employing a plurality of prioritized cell blocks and using a tree of prioritized multiplexers descending from the plurality of cell blocks.

  17. Hepa filter dissolution process

    DOE Patents [OSTI]

    Brewer, Ken N. (Arco, ID); Murphy, James A. (Idaho Falls, ID)

    1994-01-01

    A process for dissolution of spent high efficiency particulate air (HEPA) filters and then combining the complexed filter solution with other radioactive wastes prior to calcining the mixed and blended waste feed. The process is an alternate to a prior method of acid leaching the spent filters which is an inefficient method of treating spent HEPA filters for disposal.

  18. Gas-separation process

    DOE Patents [OSTI]

    Toy, L.G.; Pinnau, I.; Baker, R.W.

    1994-01-25

    A process is described for separating condensable organic components from gas streams. The process makes use of a membrane made from a polymer material that is glassy and that has an unusually high free volume within the polymer material. 6 figures.

  19. Novel wastewater treatment processes

    SciTech Connect (OSTI)

    Saber, D.L.

    1996-12-31

    Few fermentation processes are as versatile as anaerobic digestion in terms of utility, application and capability to handle feeds of varied chemical complexity and physical characteristics. The anaerobic digestion process has served the pollution control industry in the US for over 100 years in stabilizing organic sludges and wastewaters; treatment of these high-moisture-content and high-strength aqueous wastes by alternative thermal or aerobic biological processes requires much higher energy inputs than that needed to conduct anaerobic digestion. The anaerobic digestion process has taken on new importance and emphasis in recent years because of its potential application for energy and chemical production from various types of renewable-carbon resources, and because it can be coupled with certain electrochemical, thermochemical and biochemical processes to generate electric power, hydrocarbons, methanol and other high-value products. A number of initiatives have been taken to improve the anaerobic digestion process in keeping with the increasing appreciation for its utility and versatility of application in municipal, industrial and rural settings. Using processes based upon the anaerobic digestion of organic wastes, the Institute of Gas Technology has developed technologies applicable for the treatment of a wide variety of organic wastes. Increased methane gas production and enhanced waste reduction can be achieved through the ACIMET, SOLCON and HIMET Processes, depending upon concentration and characteristics of the incoming organic waste stream. These proprietary IGT waste treatment systems are described.

  20. Microsystem process networks

    DOE Patents [OSTI]

    Wegeng, Robert S [Richland, WA; TeGrotenhuis, Ward E [Kennewick, WA; Whyatt, Greg A [West Richland, WA

    2010-01-26

    Various aspects and applications or microsystem process networks are described. The design of many types of microsystems can be improved by ortho-cascading mass, heat, or other unit process operations. Microsystems having energetically efficient microchannel heat exchangers are also described. Detailed descriptions of numerous design features in microcomponent systems are also provided.

  1. Microsystem process networks

    DOE Patents [OSTI]

    Wegeng, Robert S.; TeGrotenhuis, Ward E.; Whyatt, Greg A.

    2006-10-24

    Various aspects and applications of microsystem process networks are described. The design of many types of microsystems can be improved by ortho-cascading mass, heat, or other unit process operations. Microsystems having exergetically efficient microchannel heat exchangers are also described. Detailed descriptions of numerous design features in microcomponent systems are also provided.

  2. Microsystem process networks

    DOE Patents [OSTI]

    Wegeng, Robert S.; TeGrotenhuis, Ward E.; Whyatt, Greg A.

    2007-09-18

    Various aspects and applications of microsystem process networks are described. The design of many types of Microsystems can be improved by ortho-cascading mass, heat, or other unit process operations. Microsystems having energetically efficient microchannel heat exchangers are also described. Detailed descriptions of numerous design features in microcomponent systems are also provided.

  3. HEPA filter dissolution process

    DOE Patents [OSTI]

    Brewer, K.N.; Murphy, J.A.

    1994-02-22

    A process is described for dissolution of spent high efficiency particulate air (HEPA) filters and then combining the complexed filter solution with other radioactive wastes prior to calcining the mixed and blended waste feed. The process is an alternate to a prior method of acid leaching the spent filters which is an inefficient method of treating spent HEPA filters for disposal. 4 figures.

  4. METAL PLATING PROCESS

    DOE Patents [OSTI]

    Walker, D.E.; Noland, R.A.

    1958-08-12

    A process ts described for obtaining a closely bonded coating of steel or iron on uranium. The process consists of providing, between the steel and uramium. a layer of silver. amd then pressure rolling tbe assembly at about 600 deg C until a reduction of from l0 to 50% has been obtained.

  5. Formed HIP Can Processing

    SciTech Connect (OSTI)

    Clarke, Kester Diederik

    2015-07-27

    The intent of this report is to document a procedure used at LANL for HIP bonding aluminum cladding to U-10Mo fuel foils using a formed HIP can for the Domestic Reactor Conversion program in the NNSA Office of Material, Management and Minimization, and provide some details that may not have been published elsewhere. The HIP process is based on the procedures that have been used to develop the formed HIP can process, including the baseline process developed at Idaho National Laboratory (INL). The HIP bonding cladding process development is summarized in the listed references. Further iterations with Babcock & Wilcox (B&W) to refine the process to meet production and facility requirements is expected.

  6. Elemental sulfur recovery process

    DOE Patents [OSTI]

    Flytzani-Stephanopoulos, M.; Zhicheng Hu.

    1993-09-07

    An improved catalytic reduction process for the direct recovery of elemental sulfur from various SO[sub 2]-containing industrial gas streams. The catalytic process provides combined high activity and selectivity for the reduction of SO[sub 2] to elemental sulfur product with carbon monoxide or other reducing gases. The reaction of sulfur dioxide and reducing gas takes place over certain catalyst formulations based on cerium oxide. The process is a single-stage, catalytic sulfur recovery process in conjunction with regenerators, such as those used in dry, regenerative flue gas desulfurization or other processes, involving direct reduction of the SO[sub 2] in the regenerator off gas stream to elemental sulfur in the presence of a catalyst. 4 figures.

  7. Shale oil dearsenation process

    SciTech Connect (OSTI)

    Brickman, F.E.; Degnan, T.F.; Weiss, C.S.

    1984-10-29

    This invention relates to processing shale oil and in particular to processing shale oil to reduce the arsenic content. Specifically, the invention relates to treating shale oil by a combination of processes - coking and water washing. Many shale oils produced by conventional retorting processes contain inorganic materials, such as arsenic, which interfere with subsequent refining or catalytic hydroprocessing operations. Examples of these hydroprocessing operations are hydrogenation, denitrogenation, and desulfurization. From an environmental standpoint, removal of such contaminants may be desirable even if the shale oil is to be used directly as a fuel. Hence, it is desirable that contaminants such as arsenic be removed, or reduced to low levels, prior to further processing of the shale oil or prior to its use as a fuel.

  8. Elemental sulfur recovery process

    DOE Patents [OSTI]

    Flytzani-Stephanopoulos, Maria; Hu, Zhicheng

    1993-01-01

    An improved catalytic reduction process for the direct recovery of elemental sulfur from various SO.sub.2 -containing industrial gas streams. The catalytic process provides combined high activity and selectivity for the reduction of SO.sub.2 to elemental sulfur product with carbon monoxide or other reducing gases. The reaction of sulfur dioxide and reducing gas takes place over certain catalyst formulations based on cerium oxide. The process is a single-stage, catalytic sulfur recovery process in conjunction with regenerators, such as those used in dry, regenerative flue gas desulfurization or other processes, involving direct reduction of the SO.sub.2 in the regenerator off gas stream to elemental sulfur in the presence of a catalyst.

  9. A Prescription for List-Mode Data Processing Conventions

    SciTech Connect (OSTI)

    Beddingfield, David H.; Swinhoe, Martyn Thomas; Huszti, Jozsef; Newell, Matthew R.

    2015-10-08

    There are a variety of algorithmic approaches available to process list-mode pulse streams to produce multiplicity histograms for subsequent analysis. In the development of the INCC v6.0 code to include the processing of this data format, we have noted inconsistencies in the “processed time” between the various approaches. The processed time, tp, is the time interval over which the recorded pulses are analyzed to construct multiplicity histograms. This is the time interval that is used to convert measured counts into count rates. The observed inconsistencies in tp impact the reported count rate information and the determination of the error-values associated with the derived singles, doubles, and triples counting rates. This issue is particularly important in low count-rate environments. In this report we will present a prescription for the processing of list-mode counting data that produces values that are both correct and consistent with traditional shift-register technologies. It is our objective to define conventions for list mode data processing to ensure that the results are physically valid and numerically aligned with the results from shift-register electronics.

  10. Advanced Hydrogen Liquefaction Process

    SciTech Connect (OSTI)

    Schwartz, Joseph; Kromer, Brian; Neu, Ben; Jankowiak, Jerome; Barrett, Philip; Drnevich, Raymond

    2011-09-28

    The project identified and quantified ways to reduce the cost of hydrogen liquefaction, and reduce the cost of hydrogen distribution. The goal was to reduce the power consumption by 20% and then to reduce the capital cost. Optimizing the process, improving process equipment, and improving ortho-para conversion significantly reduced the power consumption of liquefaction, but by less than 20%. Because the efficiency improvement was less than the target, the program was stopped before the capital cost was addressed. These efficiency improvements could provide a benefit to the public to improve the design of future hydrogen liquefiers. The project increased the understanding of hydrogen liquefaction by modeling different processes and thoroughly examining ortho-para separation and conversion. The process modeling provided a benefit to the public because the project incorporated para hydrogen into the process modeling software, so liquefaction processes can be modeled more accurately than using only normal hydrogen. Adding catalyst to the first heat exchanger, a simple method to reduce liquefaction power, was identified, analyzed, and quantified. The demonstrated performance of ortho-para separation is sufficient for at least one identified process concept to show reduced power cost when compared to hydrogen liquefaction processes using conventional ortho-para conversion. The impact of improved ortho-para conversion can be significant because ortho para conversion uses about 20-25% of the total liquefaction power, but performance improvement is necessary to realize a substantial benefit. Most of the energy used in liquefaction is for gas compression. Improvements in hydrogen compression will have a significant impact on overall liquefier efficiency. Improvements to turbines, heat exchangers, and other process equipment will have less impact.

  11. Femtosecond laser processing of fuel injectors - a materials processing evaluation

    SciTech Connect (OSTI)

    Stuart, B C; Wynne, A

    2000-12-16

    Lawrence Livermore National Laboratory (LLNL) has developed a new laser-based machining technology that utilizes ultrashort-pulse (0.1-1.0 picosecond) lasers to cut materials with negligible generation of heat or shock. The ultrashort pulse laser, developed for the Department of Energy (Defense Programs) has numerous applications in operations requiring high precision machining. Due to the extremely short duration of the laser pulse, material removal occurs by a different physical mechanism than in conventional machining. As a result, any material (e.g., hardened steel, ceramics, diamond, silicon, etc.) can be machined with minimal heat-affected zone or damage to the remaining material. As a result of the threshold nature of the process, shaped holes, cuts, and textures can be achieved with simple beam shaping. Conventional laser tools used for cutting or high-precision machining (e.g., sculpting, drilling) use long laser pulses (10{sup -8} to over 1 sec) to remove material by heating it to the melting or boiling point (Figure 1.1a). This often results in significant damage to the remaining material and produces considerable slag (Figure 1.2a). With ultrashort laser pulses, material is removed by ionizing the material (Figure 1.1b). The ionized plasma expands away from the surface too quickly for significant energy transfer to the remaining material. This distinct mechanism produces extremely precise and clean-edged holes without melting or degrading the remaining material (Figures 1.2 and 1.3). Since only a very small amount of material ({approx} <0.5 microns) is removed per laser pulse, extremely precise machining can be achieved. High machining speed is achieved by operating the lasers at repetition rates up to 10,000 pulses per second. As a diagnostic, the character of the short-pulse laser produced plasma enables determination of the material being machined between pulses. This feature allows the machining of multilayer materials, metal on metal or metal on

  12. Municipal waste processing apparatus

    DOE Patents [OSTI]

    Mayberry, J.L.

    1988-04-13

    This invention relates to apparatus for processing municipal waste, and more particularly to vibrating mesh screen conveyor systems for removing grit, glass, and other noncombustible materials from dry municipal waste. Municipal waste must be properly processed and disposed of so that it does not create health risks to the community. Generally, municipal waste, which may be collected in garbage trucks, dumpsters, or the like, is deposited in processing areas such as landfills. Land and environmental controls imposed on landfill operators by governmental bodies have increased in recent years, however, making landfill disposal of solid waste materials more expensive. 6 figs.

  13. Ultrasonic Processing of Materials

    SciTech Connect (OSTI)

    Meek, Thomas T.; Han, Qingyou; Jian, Xiaogang; Xu, Hanbing

    2005-06-30

    The purpose of this project was to determine the impact of a new breakthrough technology, ultrasonic processing, on various industries, including steel, aluminum, metal casting, and forging. The specific goals of the project were to evaluate core principles and establish quantitative bases for the ultrasonc processing of materials, and to demonstrate key applications in the areas of grain refinement of alloys during solidification and degassing of alloy melts. This study focussed on two classes of materials - aluminum alloys and steels - and demonstrated the application of ultrasonic processing during ingot casting.

  14. Measuring Process Safety Management

    SciTech Connect (OSTI)

    Sweeney, J.C. (ARCO Chemical Co., Newtown Square, PA (United States))

    1992-04-01

    Many companies are developing and implementing Process Safety Management (PSM) systems. Various PSM models, including those by the Center for Chemical Process Safety (CCPS), the American Petroleum Institute (API), the Chemical Manufacturers Association (CMA) and OSHA have emerged to guide the design, development and installation of these systems. These models represent distillations of the practices, methods and procedures successfully used by those who believed that a strong correlation exists between sound PSM practices and achieving reductions in the frequency and severity of process incidents. This paper describes the progress of CCPS research toward developing a PSM performance measurement model. It also provides a vision for future CCPS research to define effectiveness indices.

  15. Coal liquefaction quenching process

    DOE Patents [OSTI]

    Thorogood, Robert M.; Yeh, Chung-Liang; Donath, Ernest E.

    1983-01-01

    There is described an improved coal liquefaction quenching process which prevents the formation of coke with a minimum reduction of thermal efficiency of the coal liquefaction process. In the process, the rapid cooling of the liquid/solid products of the coal liquefaction reaction is performed without the cooling of the associated vapor stream to thereby prevent formation of coke and the occurrence of retrograde reactions. The rapid cooling is achieved by recycling a subcooled portion of the liquid/solid mixture to the lower section of a phase separator that separates the vapor from the liquid/solid products leaving the coal reactor.

  16. ITP Energy Intensive Processes: Energy-Intensive Processes Portfolio...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy-Intensive Processes Portfolio: Addressing Key Energy Challenges Across U.S. Industry ITP Energy Intensive Processes: Energy-Intensive Processes Portfolio: Addressing Key ...

  17. Direct coal liquefaction process

    DOE Patents [OSTI]

    Rindt, J.R.; Hetland, M.D.

    1993-10-26

    An improved multistep liquefaction process for organic carbonaceous mater which produces a virtually completely solvent-soluble carbonaceous liquid product. The solubilized product may be more amenable to further processing than liquid products produced by current methods. In the initial processing step, the finely divided organic carbonaceous material is treated with a hydrocarbonaceous pasting solvent containing from 10% and 100% by weight process-derived phenolic species at a temperature within the range of 300 C to 400 C for typically from 2 minutes to 120 minutes in the presence of a carbon monoxide reductant and an optional hydrogen sulfide reaction promoter in an amount ranging from 0 to 10% by weight of the moisture- and ash-free organic carbonaceous material fed to the system. As a result, hydrogen is generated via the water/gas shift reaction at a rate necessary to prevent condensation reactions. In a second step, the reaction product of the first step is hydrogenated.

  18. Associative list processing unit

    DOE Patents [OSTI]

    Hemmert, Karl Scott; Underwood, Keith D

    2014-04-01

    An associative list processing unit and method comprising employing a plurality of prioritized cell blocks and permitting inserts to occur in a single clock cycle if all of the cell blocks are not full.

  19. Continuous sulfur removal process

    DOE Patents [OSTI]

    Jalan, V.; Ryu, J.

    1994-04-26

    A continuous process for the removal of hydrogen sulfide from a gas stream using a membrane comprising a metal oxide deposited on a porous support is disclosed. 4 figures.

  20. Phenol removal pretreatment process

    DOE Patents [OSTI]

    Hames, Bonnie R.

    2004-04-13

    A process for removing phenols from an aqueous solution is provided, which comprises the steps of contacting a mixture comprising the solution and a metal oxide, forming a phenol metal oxide complex, and removing the complex from the mixture.

  1. Direct coal liquefaction process

    DOE Patents [OSTI]

    Rindt, John R.; Hetland, Melanie D.

    1993-01-01

    An improved multistep liquefaction process for organic carbonaceous mater which produces a virtually completely solvent-soluble carbonaceous liquid product. The solubilized product may be more amenable to further processing than liquid products produced by current methods. In the initial processing step, the finely divided organic carbonaceous material is treated with a hydrocarbonaceous pasting solvent containing from 10% and 100% by weight process-derived phenolic species at a temperature within the range of 300.degree. C. to 400.degree. C. for typically from 2 minutes to 120 minutes in the presence of a carbon monoxide reductant and an optional hydrogen sulfide reaction promoter in an amount ranging from 0 to 10% by weight of the moisture- and ash-free organic carbonaceous material fed to the system. As a result, hydrogen is generated via the water/gas shift reaction at a rate necessary to prevent condensation reactions. In a second step, the reaction product of the first step is hydrogenated.

  2. Materials processing with light

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Materials processing with light, plasmas and other sources of energy At the ARC various processing technologies are used to create materials, struc- tures, and devices that play an increasingly important role in high value-added manufacturing of computer and communications equipment, physical and chemical sensors, biomedical instruments and treatments, semiconductors, thin films, photovoltaics, electronic components and optical components. For example, making coatings, including paint, chrome,

  3. Postdoc Application Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program » Application Process Postdoc Application Process Point your career towards LANL: work with the best minds on the planet in an inclusive environment that is rich in intellectual vitality and opportunities for growth. Submit general application or apply for specific posted position For initial consideration, you can submit a general application to the Postdoctoral Research program and/or for a specific posted position. Access the general application or view specific posted postdoc

  4. Hydrogen recovery process

    DOE Patents [OSTI]

    Baker, Richard W.; Lokhandwala, Kaaeid A.; He, Zhenjie; Pinnau, Ingo

    2000-01-01

    A treatment process for a hydrogen-containing off-gas stream from a refinery, petrochemical plant or the like. The process includes three separation steps: condensation, membrane separation and hydrocarbon fraction separation. The membrane separation step is characterized in that it is carried out under conditions at which the membrane exhibits a selectivity in favor of methane over hydrogen of at least about 2.5.

  5. Advanced Polymer Processing Facility

    SciTech Connect (OSTI)

    Muenchausen, Ross E.

    2012-07-25

    Some conclusions of this presentation are: (1) Radiation-assisted nanotechnology applications will continue to grow; (2) The APPF will provide a unique focus for radiolytic processing of nanomaterials in support of DOE-DP, other DOE and advanced manufacturing initiatives; (3) {gamma}, X-ray, e-beam and ion beam processing will increasingly be applied for 'green' manufacturing of nanomaterials and nanocomposites; and (4) Biomedical science and engineering may ultimately be the biggest application area for radiation-assisted nanotechnology development.

  6. Retrofitting heavy oil processes

    SciTech Connect (OSTI)

    Hamilton, G.L.; Fitzgerald, M.; D'Amico, V.

    1986-01-01

    Refiners, faced with the need to process the bottom end of the heavy high sulfur crude oil barrel in today's uncertain economic environment, are reluctant to commit large amounts of money to expensive upgrading processes. In order to conserve scarce capital while improving operating margins, additional valuable products can be produced by retrofits such as conversion of an idle crude unit to visbreaking, delayed coking or deasphalting service, or conversion of hydrodesulfurizers to mild hydrocracking.

  7. Licensing Process | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Licensing Process Through licensing of its intellectual property rights, NREL provides industry with an opportunity to commercialize NREL-developed energy technologies and products. Our licensing opportunities are available to both small and large businesses-from start-ups to Fortune 500 companies. Step-by-Step Process 1. Identify and Qualify Opportunity To identify a licensing opportunity, a company can browse the Energy Innovation Portal. From the Portal, the company can review publically

  8. Coal liquefaction process

    DOE Patents [OSTI]

    Karr, Jr., Clarence

    1977-04-19

    An improved coal liquefaction process is provided which enables conversion of a coal-oil slurry to a synthetic crude refinable to produce larger yields of gasoline and diesel oil. The process is characterized by a two-step operation applied to the slurry prior to catalytic desulfurization and hydrogenation in which the slurry undergoes partial hydrogenation to crack and hydrogenate asphaltenes and the partially hydrogenated slurry is filtered to remove minerals prior to subsequent catalytic hydrogenation.

  9. Application Process and Eligibility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program » Application Process and Eligibility Application Process and Eligibility Both US and non-US citizens are eligible to apply, but US citizenship may be required for some research. Contacts Director Albert Migliori Deputy Franz Freibert 505 667-6879 Email Professional Staff Assistant Susan Ramsay 505 665 0858 Email Applications for the program shall consist of a clearly defined research proposal of up to 300 words, written by the sponsor, describing the candidate's proposed research in

  10. American Process - Alpena Biorefinery

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Sugar is the New Crude® 1 American Process - Alpena Biorefinery Lessons Learned: Theodora Retsina CEO American Process Company History * Conducted over 400 projects, in USA, Canada, Brazil, Europe, Australia * In more than 150 forest industry plants * Performed O&M services 1995 - 2010 * Designed EPC and operated power cogeneration facilities "across the fence" * Designed projects for mill shutdown installations 1999 - 2010 * Invested in biorefinery R&D - Over 48 patents

  11. Appraisal Process Protocols

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    INDEPENDENT OVERSIGHT PROGRAM APPRAISAL PROCESS PROTOCOLS December 2015 Office of Enterprise Assessments U.S. Department of Energy Independent Oversight Program Appraisal Process Protocols Preface December 2015 i Preface The U.S. Department of Energy's (DOE) Office of Enterprise Assessments (EA) is responsible for implementing an Independent Oversight Program for safety and security within the Department in accordance with DOE Policy 226.1B, Department of Energy Oversight Policy, and DOE Orders

  12. Spherical nitroguanidine process

    DOE Patents [OSTI]

    Sanchez, John A.; Roemer, Edward L.; Stretz, Lawrence A.

    1990-01-01

    A process of preparing spherical high bulk density nitroguanidine by dissing low bulk density nitroguanidine in N-methyl pyrrolidone at elevated temperatures and then cooling the solution to lower temperatures as a liquid characterized as a nonsolvent for the nitroguanidine is provided. The process is enhanced by inclusion in the solution of from about 1 ppm up to about 250 ppm of a metal salt such as nickel nitrate, zinc nitrate or chromium nitrate, preferably from about 20 to about 50 ppm.

  13. Coal liquefaction process

    DOE Patents [OSTI]

    Skinner, Ronald W.; Tao, John C.; Znaimer, Samuel

    1985-01-01

    This invention relates to an improved process for the production of liquid carbonaceous fuels and solvents from carbonaceous solid fuels, especially coal. The claimed improved process includes the hydrocracking of the light SRC mixed with a suitable hydrocracker solvent. The recycle of the resulting hydrocracked product, after separation and distillation, is used to produce a solvent for the hydrocracking of the light solvent refined coal.

  14. Helium process cycle

    DOE Patents [OSTI]

    Ganni, Venkatarao

    2008-08-12

    A unique process cycle and apparatus design separates the consumer (cryogenic) load return flow from most of the recycle return flow of a refrigerator and/or liquefier process cycle. The refrigerator and/or liquefier process recycle return flow is recompressed by a multi-stage compressor set and the consumer load return flow is recompressed by an independent consumer load compressor set that maintains a desirable constant suction pressure using a consumer load bypass control valve and the consumer load return pressure control valve that controls the consumer load compressor's suction pressure. The discharge pressure of this consumer load compressor is thereby allowed to float at the intermediate pressure in between the first and second stage recycle compressor sets. Utilizing the unique gas management valve regulation, the unique process cycle and apparatus design in which the consumer load return flow is separate from the recycle return flow, the pressure ratios of each recycle compressor stage and all main pressures associated with the recycle return flow are allowed to vary naturally, thus providing a naturally regulated and balanced floating pressure process cycle that maintains optimal efficiency at design and off-design process cycle capacity and conditions automatically.

  15. Helium process cycle

    DOE Patents [OSTI]

    Ganni, Venkatarao

    2007-10-09

    A unique process cycle and apparatus design separates the consumer (cryogenic) load return flow from most of the recycle return flow of a refrigerator and/or liquefier process cycle. The refrigerator and/or liquefier process recycle return flow is recompressed by a multi-stage compressor set and the consumer load return flow is recompressed by an independent consumer load compressor set that maintains a desirable constant suction pressure using a consumer load bypass control valve and the consumer load return pressure control valve that controls the consumer load compressor's suction pressure. The discharge pressure of this consumer load compressor is thereby allowed to float at the intermediate pressure in between the first and second stage recycle compressor sets. Utilizing the unique gas management valve regulation, the unique process cycle and apparatus design in which the consumer load return flow is separate from the recycle return flow, the pressure ratios of each recycle compressor stage and all main pressures associated with the recycle return flow are allowed to vary naturally, thus providing a naturally regulated and balanced floating pressure process cycle that maintains optimal efficiency at design and off-design process cycle capacity and conditions automatically.

  16. Polycrystalline semiconductor processing

    DOE Patents [OSTI]

    Glaeser, Andreas M. (Scituate, MA); Haggerty, John S. (Lincoln, MA); Danforth, Stephen C. (Winchester, MA)

    1983-01-01

    A process for forming large-grain polycrystalline films from amorphous films for use as photovoltaic devices. The process operates on the amorphous film and uses the driving force inherent to the transition from the amorphous state to the crystalline state as the force which drives the grain growth process. The resultant polycrystalline film is characterized by a grain size that is greater than the thickness of the film. A thin amorphous film is deposited on a substrate. The formation of a plurality of crystalline embryos is induced in the amorphous film at predetermined spaced apart locations and nucleation is inhibited elsewhere in the film. The crystalline embryos are caused to grow in the amorphous film, without further nucleation occurring in the film, until the growth of the embryos is halted by imgingement on adjacently growing embryos. The process is applicable to both batch and continuous processing techniques. In either type of process, the thin amorphous film is sequentially doped with p and n type dopants. Doping is effected either before or after the formation and growth of the crystalline embryos in the amorphous film, or during a continuously proceeding crystallization step.

  17. Studsvik Processing Facility Update

    SciTech Connect (OSTI)

    Mason, J. B.; Oliver, T. W.; Hill, G. M.; Davin, P. F.; Ping, M. R.

    2003-02-25

    Studsvik has completed over four years of operation at its Erwin, TN facility. During this time period Studsvik processed over 3.3 million pounds (1.5 million kgs) of radioactive ion exchange bead resin, powdered filter media, and activated carbon, which comprised a cumulative total activity of 18,852.5 Ci (6.98E+08 MBq). To date, the highest radiation level for an incoming resin container has been 395 R/hr (3.95 Sv/h). The Studsvik Processing Facility (SPF) has the capability to safely and efficiently receive and process a wide variety of solid and liquid Low Level Radioactive Waste (LLRW) streams including: Ion Exchange Resins (IER), activated carbon (charcoal), graphite, oils, solvents, and cleaning solutions with contact radiation levels of up to 400 R/hr (4.0 Sv/h). The licensed and heavily shielded SPF can receive and process liquid and solid LLRWs with high water and/or organic content. This paper provides an overview of the last four years of commercial operations processing radioactive LLRW from commercial nuclear power plants. Process improvements and lessons learned will be discussed.

  18. Polycrystalline semiconductor processing

    DOE Patents [OSTI]

    Glaeser, A.M.; Haggerty, J.S.; Danforth, S.C.

    1983-04-05

    A process is described for forming large-grain polycrystalline films from amorphous films for use as photovoltaic devices. The process operates on the amorphous film and uses the driving force inherent to the transition from the amorphous state to the crystalline state as the force which drives the grain growth process. The resultant polycrystalline film is characterized by a grain size that is greater than the thickness of the film. A thin amorphous film is deposited on a substrate. The formation of a plurality of crystalline embryos is induced in the amorphous film at predetermined spaced apart locations and nucleation is inhibited elsewhere in the film. The crystalline embryos are caused to grow in the amorphous film, without further nucleation occurring in the film, until the growth of the embryos is halted by impingement on adjacently growing embryos. The process is applicable to both batch and continuous processing techniques. In either type of process, the thin amorphous film is sequentially doped with p and n type dopants. Doping is effected either before or after the formation and growth of the crystalline embryos in the amorphous film, or during a continuously proceeding crystallization step. 10 figs.

  19. THE COLD AND DARK PROCESS AT THE SAVANNAH RIVER SITE

    SciTech Connect (OSTI)

    Gilmour, J; William Austin, W; Cathy Sizemore, C

    2007-01-31

    The deactivation and decommissioning (D&D) of a facility exposes D&D workers to numerous hazards. One of the more serious hazards is coming into contact to hazardous energy sources (e.g. electrical, pressurized steam). At the Savannah River Site (SRS) a formal process for identifying and eliminating sources of hazardous energy was developed and is called ''Cold & Dark''. Several ''near miss'' events involving cutting of energized conductors during D&D work in buildings thought to be isolated identified the need to have a formal process to identify and isolate these potentially hazardous systems. This process was developed using lessons learned from D&D activities at the Rocky Flats Environmental Technology Site (Rocky Flats) in Colorado. The Cold & Dark process defines an isolation boundary (usually a building perimeter) and then systematically identifies all of the penetrations through this boundary. All penetrations that involve hazardous energy sources are then physically air-gapped. The final product is a documented declaration of isolation performed by a team involving operations, engineering, and project management. Once the Cold & Dark declaration is made for a building work can proceed without the usual controls used in an operational facility (e.g. lockout/tagout, arc flash PPE). It is important to note that the Cold & Dark process does not remove all hazards from a facility. Work planning and controls still need to address hazards that can be present from such things as chemicals, radiological contamination, residual liquids, etc., as well as standard industrial hazards.

  20. Uranium Processing Facility | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Uranium Processing Facility

  1. Sandia National Laboratories: Careers: Hiring Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Alternatively, you can submit a separate application for each job. Note: You will only be considered for jobs that you apply to. Saving your application for later Save your ...

  2. Registration Process for Coaches | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    login page to enter your username and password. Please note that there are tools on this page to help you recover your username and password: "Forgot Username" and "Reset Password." ...

  3. NREL: Process Development and Integration Laboratory - Processing in the

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Atmospheric Processing Platform Processing in the Atmospheric Processing Platform This page provides details on processing in the Atmospheric Processing platform. Photo of a window of a glove box, showing four rubber gloves extending outward. Sample preparation glove box in the Atmospheric Processing platform. Sample Preparation Box The sample preparation box allows samples to be loaded into platens and prepared for further processing. Large-Area Rapid Thermal Processing This rapid thermal

  4. U.S. Natural Gas Plant Processing

    U.S. Energy Information Administration (EIA) Indexed Site

    Area: U.S. Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Data Series Area Jan-16 Feb-16 Mar-16 Apr-16 May-16 Jun-16 View History NGPL Production, Gaseous Equivalent (Million Cubic Feet) 148,450 139,621 157,047 151,450 160,290 156,305 1973-2016

  5. U.S. Natural Gas Plant Processing

    U.S. Energy Information Administration (EIA) Indexed Site

    Federal Offshore Gulf of Mexico Alabama Alaska Arkansas California Colorado Florida Illinois Indiana Kansas Kentucky Louisiana Michigan Mississippi Montana Nebraska New Mexico North Dakota Ohio Oklahoma Pennsylvania South Dakota Tennessee Texas Utah West Virginia Wyoming Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Data Series Area 2008 2009 2010 2011 2012 2013 View History Natural Gas

  6. NEPTUNIUM OXIDE PROCESSING

    SciTech Connect (OSTI)

    Jordan, J; Watkins, R; Hensel, S

    2009-05-27

    The Savannah River Site's HB-Line Facility completed a campaign in which fifty nine cans of neptunium oxide were produced and shipped to the Idaho National Laboratory in the 9975 shipping container. The neptunium campaign was divided into two parts: Part 1 which consisted of oxide made from H-Canyon neptunium solution which did not require any processing prior to conversion into an oxide, and Part 2 which consisted of oxide made from additional H-Canyon neptunium solutions which required processing to purify the solution prior to conversion into an oxide. The neptunium was received as a nitrate solution and converted to oxide through ion-exchange column extraction, precipitation, and calcination. Numerous processing challenges were encountered in order make a final neptunium oxide product that could be shipped in a 9975 shipping container. Among the challenges overcome was the issue of scale: translating lab scale production into full facility production. The balance between processing efficiency and product quality assurance was addressed during this campaign. Lessons learned from these challenges are applicable to other processing projects.

  7. Mediation Process | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mediation Process Mediation Process This document generally discusses the DOE HQ mediation process. OCPR-HQ-003 Final - Mediation Process.pdf (106.11 KB) More Documents & Publications Employee Reminders Management Reminders Agreement to Mediate

  8. PROCESSING OF RADIOACTIVE WASTE

    DOE Patents [OSTI]

    Allemann, R.T.; Johnson, B.M. Jr.

    1961-10-31

    A process for concentrating fission-product-containing waste solutions from fuel element processing is described. The process comprises the addition of sugar to the solution, preferably after it is made alkaline; spraying the solution into a heated space whereby a dry powder is formed; heating the powder to at least 220 deg C in the presence of oxygen whereby the powder ignites, the sugar is converted to carbon, and the salts are decomposed by the carbon; melting the powder at between 800 and 900 deg C; and cooling the melt. (AEC) antidiuretic hormone from the blood by the liver. Data are summarized from the following: tracer studies on cardiovascular functions; the determination of serum protein-bound iodine; urinary estrogen excretion in patients with arvanced metastatic mammary carcinoma; the relationship between alheroclerosis aad lipoproteins; the physical chemistry of lipoproteins; and factors that modify the effects of densely ionizing radia

  9. Cantilever epitaxial process

    DOE Patents [OSTI]

    Ashby, Carol I.; Follstaedt, David M.; Mitchell, Christine C.; Han, Jung

    2003-07-29

    A process of growing a material on a substrate, particularly growing a Group II-VI or Group III-V material, by a vapor-phase growth technique where the growth process eliminates the need for utilization of a mask or removal of the substrate from the reactor at any time during the processing. A nucleation layer is first grown upon which a middle layer is grown to provide surfaces for subsequent lateral cantilever growth. The lateral growth rate is controlled by altering the reactor temperature, pressure, reactant concentrations or reactant flow rates. Semiconductor materials, such as GaN, can be produced with dislocation densities less than 10.sup.7 /cm.sup.2.

  10. A lube hydrodearomatization process

    SciTech Connect (OSTI)

    Ramos, R.Z. )

    1988-06-01

    The current worldwide demand of lubricating oils has increased the research for new technologies to obtain products with better quality, using processes less complicated than the current ones and at the same time decrease the process costs. The most familiar general process to obtain lubricating oils is by means of aromatic extraction with solvent. However, this stage represents elevated cost by raw materials consumptions; for that reason, it has increased the study of new catalytic technologies to substitute this step. In this work we are showing the last advances obtained by IMP developments about the application of the catalytic hydrogenation of aromatic compounds in lubricating oils, using a catalyst containing molybdenum as active metal and nickel and/or phosporous as promoters, - supported on gamma alumina with different concentration of metals. These catalysts have been evaluated in a pilot plant unit using several feeds of lubricating oils at different operating conditions, obtaining products with better quality than those produced by solvent extraction.

  11. Quartz resonator processing system

    DOE Patents [OSTI]

    Peters, Roswell D. M.

    1983-01-01

    Disclosed is a single chamber ultra-high vacuum processing system for the oduction of hermetically sealed quartz resonators wherein electrode metallization and sealing are carried out along with cleaning and bake-out without any air exposure between the processing steps. The system includes a common vacuum chamber in which is located a rotatable wheel-like member which is adapted to move a plurality of individual component sets of a flat pack resonator unit past discretely located processing stations in said chamber whereupon electrode deposition takes place followed by the placement of ceramic covers over a frame containing a resonator element and then to a sealing stage where a pair of hydraulic rams including heating elements effect a metallized bonding of the covers to the frame.

  12. Powder treatment process

    DOE Patents [OSTI]

    Weyand, J.D.

    1988-02-09

    Disclosed are: (1) a process comprising spray drying a powder-containing slurry, the slurry containing a powder constituent susceptible of oxidizing under the temperature conditions of the spray drying, while reducing the tendency for oxidation of the constituent by including as a liquid constituent of the slurry an organic liquid; (2) a process comprising spray drying a powder-containing slurry, the powder having been pretreated to reduce content of a powder constituent susceptible of oxidizing under the temperature conditions of the spray drying, the pretreating comprising heating the powder to react the constituent; and (3) a process comprising reacting ceramic powder, grinding the reacted powder, slurrying the ground powder, spray drying the slurried powder, and blending the dried powder with metal powder. 2 figs.

  13. Powder treatment process

    DOE Patents [OSTI]

    Weyand, John D. (Greensburg, PA)

    1988-01-01

    (1) A process comprising spray drying a powder-containing slurry, the slurry containing a powder constituent susceptible of oxidizing under the temperature conditions of the spray drying, while reducing the tendency for oxidation of the constituent by including as a liquid constituent of the slurry an organic liquid; (2) a process comprising spray drying a powder-containing slurry, the powder having been pretreated to reduce content of a powder constituent susceptible of oxidizing under the temperature conditions of the spray drying, the pretreating comprising heating the powder to react the constituent; and (3) a process comprising reacting ceramic powder, grinding the reacted powder, slurrying the ground powder, spray drying the slurried powder, and blending the dried powder with metal powder.

  14. URANIUM PRECIPITATION PROCESS

    DOE Patents [OSTI]

    Thunaes, A.; Brown, E.A.; Smith, H.W.; Simard, R.

    1957-12-01

    A method for the recovery of uranium from sulfuric acid solutions is described. In the present process, sulfuric acid is added to the uranium bearing solution to bring the pH to between 1 and 1.8, preferably to about 1.4, and aluminum metal is then used as a reducing agent to convert hexavalent uranium to the tetravalent state. As the reaction proceeds, the pH rises amd a selective precipitation of uranium occurs resulting in a high grade precipitate. This process is an improvement over the process using metallic iron, in that metallic aluminum reacts less readily than metallic iron with sulfuric acid, thus avoiding consumption of the reducing agent and a raising of the pH without accomplishing the desired reduction of the hexavalent uranium in the solution. Another disadvantage to the use of iron is that positive ferric ions will precipitate with negative phosphate and arsenate ions at the pH range employed.

  15. URANIUM RECOVERY PROCESS

    DOE Patents [OSTI]

    Yeager, J.H.

    1958-08-12

    In the prior art processing of uranium ores, the ore is flrst digested with nitric acid and filtered, and the uranium values are then extracted tom the filtrate by contacting with an organic solvent. The insoluble residue has been processed separately in order to recover any uranium which it might contain. The improvement consists in contacting a slurry, composed of both solution and residue, with the organic solvent prior to filtration. Tbe result is that uranium values contained in the residue are extracted along with the uranium values contained th the solution in one step.

  16. Enforcement Process Overview Changes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SAFETY AND SECURITY ENFORCEMENT PROCESS OVERVIEW CHANGES JULY 2016  The excerpts below show the changes made, in redline/strikeout, from the April 2015 version to the July 2016 version of the Enforcement Process Overview.  The page numbers below refer to page numbers of the July 2016 version of the document.  In the July 2016 version of the document on this website, the areas where these changes have been made are marked by a vertical line in the left margin. Page 25 Interview

  17. Coking and gasification process

    DOE Patents [OSTI]

    Billimoria, Rustom M.; Tao, Frank F.

    1986-01-01

    An improved coking process for normally solid carbonaceous materials wherein the yield of liquid product from the coker is increased by adding ammonia or an ammonia precursor to the coker. The invention is particularly useful in a process wherein coal liquefaction bottoms are coked to produce both a liquid and a gaseous product. Broadly, ammonia or an ammonia precursor is added to the coker ranging from about 1 to about 60 weight percent based on normally solid carbonaceous material and is preferably added in an amount from about 2 to about 15 weight percent.

  18. Biomass Processing Photolibrary

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Research related to bioenergy is a major focus in the U.S. as science agencies, universities, and commercial labs seek to create new energy-efficient fuels. The Biomass Processing Project is one of the funded projects of the joint USDA-DOE Biomass Research and Development Initiative. The Biomass Processing Photolibrary has numerous images, but there are no accompanying abstracts to explain what you are seeing. The project website, however, makes available the full text of presentations and publications and also includes an exhaustive biomass glossary that is being developed into an ASAE Standard.

  19. PROCESS OF RECOVERING URANIUM

    DOE Patents [OSTI]

    Carter, J.M.; Larson, C.E.

    1958-10-01

    A process is presented for recovering uranium values from calutron deposits. The process consists in treating such deposits to produce an oxidlzed acidic solution containing uranium together with the following imparities: Cu, Fe, Cr, Ni, Mn, Zn. The uranium is recovered from such an impurity-bearing solution by adjusting the pH of the solution to the range 1.5 to 3.0 and then treating the solution with hydrogen peroxide. This results in the precipitation of uranium peroxide which is substantially free of the metal impurities in the solution. The peroxide precipitate is then separated from the solution, washed, and calcined to produce uranium trioxide.

  20. Actinide metal processing

    DOE Patents [OSTI]

    Sauer, N.N.; Watkin, J.G.

    1992-03-24

    A process for converting an actinide metal such as thorium, uranium, or plutonium to an actinide oxide material by admixing the actinide metal in an aqueous medium with a hypochlorite as an oxidizing agent for sufficient time to form the actinide oxide material and recovering the actinide oxide material is described together with a low temperature process for preparing an actinide oxide nitrate such as uranyl nitrate. Additionally, a composition of matter comprising the reaction product of uranium metal and sodium hypochlorite is provided, the reaction product being an essentially insoluble uranium oxide material suitable for disposal or long term storage.

  1. Solar industrial process heat

    SciTech Connect (OSTI)

    Lumsdaine, E.

    1981-04-01

    The aim of the assessment reported is to candidly examine the contribution that solar industrial process heat (SIPH) is realistically able to make in the near and long-term energy futures of the United States. The performance history of government and privately funded SIPH demonstration programs, 15 of which are briefly summarized, and the present status of SIPH technology are discussed. The technical and performance characteristics of solar industrial process heat plants and equipment are reviewed, as well as evaluating how the operating experience of over a dozen SIPH demonstration projects is influencing institutional acceptance and economoc projections. Implications for domestic energy policy and international implications are briefly discussed. (LEW)

  2. Cyclic membrane separation process

    DOE Patents [OSTI]

    Bowser, John

    2004-04-13

    A cyclic process for controlling environmental emissions of volatile organic compounds (VOC) from vapor recovery in storage and dispensing operations of liquids maintains a vacuum in the storage tank ullage. In one of a two-part cyclic process ullage vapor is discharged through a vapor recovery system in which VOC are stripped from vented gas with a selectively gas permeable membrane. In the other part, the membrane is inoperative while gas pressure rises in the ullage. Ambient air is charged to the membrane separation unit during the latter part of the cycle.

  3. Cyclic membrane separation process

    DOE Patents [OSTI]

    Nemser, Stuart M.

    2005-05-03

    A cyclic process for controlling environmental emissions of volatile organic compounds (VOC) from vapor recovery in storage and dispensing operations of liquids maintains a vacuum in the storage tank ullage. In the first part of a two-part cyclic process ullage vapor is discharged through a vapor recovery system in which VOC are stripped from vented gas with a selectively gas permeable membrane. In the second part, the membrane is inoperative while gas pressure rises in the ullage. In one aspect of this invention, a vacuum is drawn in the membrane separation unit thus reducing overall VOC emissions.

  4. Plasma Processing Of Hydrocarbon

    SciTech Connect (OSTI)

    Grandy, Jon D; Peter C. Kong; Brent A. Detering; Larry D. Zuck

    2007-05-01

    The Idaho National Laboratory (INL) developed several patented plasma technologies for hydrocarbon processing. The INL patents include nonthermal and thermal plasma technologies for direct natural gas to liquid conversion, upgrading low value heavy oil to synthetic light crude, and to convert refinery bottom heavy streams directly to transportation fuel products. Proof of concepts has been demonstrated with bench scale plasma processes and systems to convert heavy and light hydrocarbons to higher market value products. This paper provides an overview of three selected INL patented plasma technologies for hydrocarbon conversion or upgrade.

  5. Sequential elution process

    DOE Patents [OSTI]

    Kingsley, I.S.

    1987-01-06

    A process and apparatus are disclosed for the separation of complex mixtures of carbonaceous material by sequential elution with successively stronger solvents. In the process, a column containing glass beads is maintained in a fluidized state by a rapidly flowing stream of a weak solvent, and the sample is injected into this flowing stream such that a portion of the sample is dissolved therein and the remainder of the sample is precipitated therein and collected as a uniform deposit on the glass beads. Successively stronger solvents are then passed through the column to sequentially elute less soluble materials. 1 fig.

  6. Allocation Year Rollover process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Allocatio Year Rollover process Allocation Year Rollover process December 23, 2013 by Francesca Verdier Allocation Year 2013 (AY13) ends at 23:59:59 on Monday, January 13, 2014. AY14 runs from Tuesday, January 14, 2014 through Monday, January 12, 2015. The major features of the rollover are: charging acroess the AY boundary: All batch jobs will continue running during the rollover. Time accrued before midnight will be charged to AY13 repos; time accrued after midnight will be charged to AY14

  7. Lasers in materials processing

    SciTech Connect (OSTI)

    Davis, J.I.; Rockower, E.B.

    1981-01-01

    A status report on the uranium Laser Isotope Separation (LIS) Program at the Lawrence Livermore National Laboratory is presented. Prior to this status report, process economic analysis is presented so as to understand how the unique properties of laser photons can be best utilized in the production of materials and components despite the high cost of laser energy. The characteristics of potential applications that are necessary for success are identified, and those factors that have up to now frustrated attempts to find commercially viable laser induced chemical and physical process for the production of new or existing materials are pointed out.

  8. Actinide metal processing

    DOE Patents [OSTI]

    Sauer, Nancy N.; Watkin, John G.

    1992-01-01

    A process of converting an actinide metal such as thorium, uranium, or plnium to an actinide oxide material by admixing the actinide metal in an aqueous medium with a hypochlorite as an oxidizing agent for sufficient time to form the actinide oxide material and recovering the actinide oxide material is provided together with a low temperature process of preparing an actinide oxide nitrate such as uranyl nitrte. Additionally, a composition of matter comprising the reaction product of uranium metal and sodium hypochlorite is provided, the reaction product being an essentially insoluble uranium oxide material suitable for disposal or long term storage.

  9. Reversible brazing process

    DOE Patents [OSTI]

    Pierce, Jim D.; Stephens, John J.; Walker, Charles A.

    1999-01-01

    A method of reversibly brazing surfaces together. An interface is affixed to each surface. The interfaces can be affixed by processes such as mechanical joining, welding, or brazing. The two interfaces are then brazed together using a brazing process that does not defeat the surface to interface joint. Interfaces of materials such as Ni-200 can be affixed to metallic surfaces by welding or by brazing with a first braze alloy. The Ni-200 interfaces can then be brazed together using a second braze alloy. The second braze alloy can be chosen so that it minimally alters the properties of the interfaces to allow multiple braze, heat and disassemble, rebraze cycles.

  10. Waste Processing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Processing Waste Processing Workers process and repackage waste at the Transuranic Waste Processing Center’s Cask Processing Enclosure. Workers process and repackage waste at the Transuranic Waste Processing Center's Cask Processing Enclosure. Transuranic waste, or TRU, is one of several types of waste handled by Oak Ridge's EM program. This waste contains manmade elements heavier than uranium, hence the name "trans" or "beyond" uranium. Transuranic waste material

  11. Examinations of the new direct smelting processes for iron and steelmaking. [ELRED process, INRED process, SKF Plasmasmelt process, McDowell-Wellman process, the direct converter smelting process

    SciTech Connect (OSTI)

    Moore, J.T.

    1982-06-01

    This paper discusses the need for a radical technological change in the production of iron and steel and suggests the salient features that should be addressed. Five new direct smelting steelmaking systems have been compared with blast furnace/basic oxygen furnace route. These are the ELRED process the INRED process, the SKF Plasmasmelt process, the McDowell-Wellman process, and a converter smelting process. 20 refs.

  12. Catalytic coal hydroliquefaction process

    DOE Patents [OSTI]

    Garg, Diwakar (Macungie, PA)

    1984-01-01

    A process is described for the liquefaction of coal in a hydrogen donor solvent in the presence of hydrogen and a co-catalyst combination of iron and a Group VI or Group VIII non-ferrous metal or compounds of the catalysts.

  13. Catalytic coal liquefaction process

    DOE Patents [OSTI]

    Garg, Diwakar (Macungie, PA); Sunder, Swaminathan (Allentown, PA)

    1986-01-01

    An improved process for catalytic solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a solvent comprises using as catalyst a mixture of a 1,2- or 1,4-quinone and an alkaline compound, selected from ammonium, alkali metal, and alkaline earth metal oxides, hydroxides or salts of weak acids.

  14. Actinide recovery process

    DOE Patents [OSTI]

    Muscatello, Anthony C. (Arvada, CO); Navratil, James D. (Arvada, CO); Saba, Mark T. (Arvada, CO)

    1987-07-28

    Process for the removal of plutonium polymer and ionic actinides from aqueous solutions by absorption onto a solid extractant loaded on a solid inert support such as polystyrenedivinylbenzene. The absorbed actinides can then be recovered by incineration, by stripping with organic solvents, or by acid digestion. Preferred solid extractants are trioctylphosphine oxide and octylphenyl-N,N-diisobutylcarbamoylmethylphosphine oxide and the like.

  15. Process for functionalizing alkanes

    DOE Patents [OSTI]

    Bergman, R.G.; Janowicz, A.H.; Periana, R.A.

    1988-05-24

    Process for functionalizing saturated hydrocarbons comprises: (a) reacting said saturated hydrocarbons of the formula: R[sub 1]H wherein H represents a hydrogen atom; and R[sub 1] represents a saturated hydrocarbon radical, with a metal complex of the formula: CpRh[P(R[sub 2])[sub 3

  16. Catalytic cracking process

    DOE Patents [OSTI]

    Lokhandwala, Kaaeid A.; Baker, Richard W.

    2001-01-01

    Processes and apparatus for providing improved catalytic cracking, specifically improved recovery of olefins, LPG or hydrogen from catalytic crackers. The improvement is achieved by passing part of the wet gas stream across membranes selective in favor of light hydrocarbons over hydrogen.

  17. Catalytic oxidative dehydrogenation process

    DOE Patents [OSTI]

    Schmidt, Lanny D.; Huff, Marylin

    2002-01-01

    A process for the production of a mono-olefin from a gaseous paraffinic hydrocarbon having at least two carbon atoms or mixtures thereof comprising reacting said hydrocarbons and molecular oxygen in the presence of a platinum catalyst. The catalyst consist essentially of platinum supported on alumina or zirconia monolith, preferably zirconia and more preferably in the absence of palladium, rhodium and gold.

  18. Biochemical Platform Processing Integration

    SciTech Connect (OSTI)

    2006-06-01

    The objective of this project is to facilitate deployment of enzyme-based biomass conversion technology. The immediate goal is to explore integration issues that impact process performance and to demonstrate improved performance of the lower-cost enzymes being developed by Genencor and Novozymes.

  19. Catalytic coal liquefaction process

    DOE Patents [OSTI]

    Garg, D.; Sunder, S.

    1986-12-02

    An improved process for catalytic solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a solvent comprises using as catalyst a mixture of a 1,2- or 1,4-quinone and an alkaline compound, selected from ammonium, alkali metal, and alkaline earth metal oxides, hydroxides or salts of weak acids. 1 fig.

  20. Sulfur recovery process

    SciTech Connect (OSTI)

    Hise, R.E.; Cook, W.J.

    1991-06-04

    This paper describes a method for recovering sulfur from a process feed stream mixture of gases comprising sulfur-containing compounds including hydrogen sulfide using the Claus reaction to convert sulfur-containing compounds to elemental sulfur and crystallization to separate sulfur-containing compounds from a tail gas of the Claus reaction for further processing as a recycle stream. It comprises: providing a Claus feed stream containing a stoichiometric excess of hydrogen sulfide, the Claus feed stream including the process feed stream and the recycles stream; introducing the Claus feed stream and an oxidizing agent into a sulfur recovery unit for converting sulfur-containing compounds in the Claus feed stream to elemental sulfur; withdrawing the tail gas from the sulfur recovery unit; separating water from the tail gas to producing a dehydrated tail gas; separating sulfur-containing compounds including carbonyl sulfide from the dehydrated tail gas as an excluded material by crystallization and withdrawing an excluded material-enriched output from the crystallization to produce the recycle stream; and combining the recycle stream with the process feed stream to produce the Claus feed stream.