Powered by Deep Web Technologies
Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

An Analysis of the Residential Energy Savings from the Implementation of the 2001 IECC and 2006 NAECA Appliance Standards in the State of Texas  

E-Print Network (OSTI)

This paper presents results of an analysis of the annual electricity and natural gas savings from implementation of the 2001 International Energy Conservation Code (IECC) specifications with updated 2006 specifications for mechanical systems to new single-family residential construction, using a code traceable DOE-2 simulation for two locations in Texas. In this analysis a sensitivity analysis was performed which included the impact of changing the Seasonal Energy Efficiency Ratio (SEER) and Heating Seasonal Performance Factor (HSPF) values in code-compliant construction (i.e., SEER 13, HSPF 7.7) as required by National Appliance Energy Conservation Act (NAECA, 2006). The results show that the annual energy consumption for a typical single-family residence decreased by 18.8% when comparing a pre-code house with natural gas heating, where the SEER for the air-conditioner was increased from 10 to 13, to a code-compliant house incorporating the 2006 NAECA standards in Houston , and by 16.0% for a similar house in Dallas/Fort Worth area. In a house employing a heat pump as a source of heating, where the SEER for the air-conditioner was increased from 10 to 13 and the HSPF was increased from 6.6 to 7.7, the annual energy consumption decreased by 18.2% for a house in Houston and by 16.6% for a similar house in Dallas/Fort Worth.

Mukhopadhyay, J.; Liu, Z.; Malhotra, M.; Haberl, J.; Gilman, D.; Montgomery, C.; Culp, C.; Yazdani, B.

2008-12-01T23:59:59.000Z

2

A Comparative Analysis of Residential Energy Use for 2009 IECC Code Compliance and 2001 IECC Compliance with 2006 NAECA Appliance Standards for Selected Climate Zones in Texas  

E-Print Network (OSTI)

This paper presents results of a comparative analysis of the electricity and natural gas savings from the implementation of 2009 International Energy Conservation Code (IECC) when compared with the 2001 IECC1 specifications with 2006 NAECA for a new single-family residential construction. The analysis uses a DOE-2 simulation for five locations in Texas (Houston, Brownsville, Dallas/Fort Worth, El Paso and Amarillo). The analysis shows that a code compliant house built to the specifications of the 2009 IECC uses 10% 16% less site energy annually than a house meeting the specifications of the 2001 IECC, for an air-conditioned house with a natural gas furnace. The results also show that an air conditioned 2009 code - compliant house with a heat pump uses 10% - 14% less site energy annually.

Mukhopadhyay, J.; Baltazar, J. C.; Liu, Z.; Haberl, J.; Culp, C.; Yazdani, B.

2010-08-01T23:59:59.000Z

3

Water Quality Standards Implementation (Oklahoma) | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementation (Oklahoma) Water Quality Standards Implementation (Oklahoma) Eligibility Agricultural Construction Fuel Distributor Industrial InstallerContractor Investor-Owned...

4

Development and implementation of energy efficiency standards...  

NLE Websites -- All DOE Office Websites (Extended Search)

Development and implementation of energy efficiency standards and labeling programs in China: Progress and challenges Title Development and implementation of energy efficiency...

5

Implementation Report: Energy Conservation Standards Activities  

NLE Websites -- All DOE Office Websites (Extended Search)

Implementation Report: Implementation Report: Energy Conservation Standards Activities Submitted Pursuant to Section 141 of the Energy Policy Act of 2005 U.S. Department of Energy August 2006 Table of Contents List of Acronyms .............................................................................................................. 3 1 Introduction .............................................................................................................. 4 2 Multi-Year Schedule and Implementation Update............................................. 6 2.1 Multi-Year Schedule........................................................................................... 6 2.2 Implementation Update ......................................................................................

6

Implementation Report: Energy Conservation Standards Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementation Report: Implementation Report: Energy Conservation Standards Activities Submitted Pursuant to Section 141 of the Energy Policy Act of 2005 U.S. Department of Energy August 2006 Table of Contents List of Acronyms .............................................................................................................. 3 1 Introduction .............................................................................................................. 4 2 Multi-Year Schedule and Implementation Update............................................. 6 2.1 Multi-Year Schedule........................................................................................... 6 2.2 Implementation Update ......................................................................................

7

Implementation of Sustainable Manufacturing Standards  

Science Conference Proceedings (OSTI)

... Manufacturing Standards Kathi Futornick, LEED AP Global Sustainability Practice URS Corporation NIST Workshop October 13-15, 2009 ...

2009-10-20T23:59:59.000Z

8

State Appliance Standards (released in AEO2009)  

Reports and Publications (EIA)

State appliance standards have existed for decades, starting with Californias enforcement of minimum efficiency requirements for refrigerators and several other products in 1979. In 1987, recognizing that different efficiency standards for the same products in different States could create problems for manufacturers, Congress enacted the National Appliance Energy Conservation Act (NAECA), which initially covered 12 products. The Energy Policy Act of 1992 (EPACT92), EPACT2005, and EISA2007 added additional residential and commercial products to the 12 products originally specified under NAECA.

Information Center

2009-03-31T23:59:59.000Z

9

Implementation Report: Energy Conservation Standards Activities  

NLE Websites -- All DOE Office Websites (Extended Search)

Implementation Report: Implementation Report: Energy Conservation Standards Activities Submitted Pursuant to: Section 141 of the Energy Policy Act of 2005 & Section 305 of the Energy Independence and Security Act of 2007 U.S. Department of Energy August 2009 U.S. Department of Energy 2 Table of Contents List of Acronyms ...................................................................................................................................... 3 Introduction .............................................................................................................................................. 4

10

Implementation Report: Energy Conservation Standards Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementation Report: Implementation Report: Energy Conservation Standards Activities Submitted Pursuant to: Section 141 of the Energy Policy Act of 2005 & Section 305 of the Energy Independence and Security Act of 2007 U.S. Department of Energy August 2009 U.S. Department of Energy 2 Table of Contents List of Acronyms ...................................................................................................................................... 3 Introduction .............................................................................................................................................. 4

11

Reference Manual and Procedures for Implementation of PURPA Standards...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PURPA Standards in EISA 2007 REPORT TO CONGRESS ON COMPETITION IN WHOLESALE AND RETAIL MARKETS FOR ELECTRIC ENERGY Re: DOE Request for Information - Implementing the National...

12

Implementation Report: Energy Conservation Standards Activities  

NLE Websites -- All DOE Office Websites (Extended Search)

to: to: Section 141 of the Energy Policy Act of 2005 & Section 305 of the Energy Independence and Security Act of 2007 U.S. Department of Energy February 2008 Table of Contents List of Acronyms .............................................................................................................. 3 Introduction ...................................................................................................................... 4 Section 1: Backlog and EPACT 2005.............................................................................. 5 State of New York, et al. v. Bodman; and NRDC, Inc. et al. v. Bodman ...................... 5 Multi-Year Schedule and Implementation Update................................................. 7 Multi-Year Schedule ................................................................................................ 7

13

Implementation Report: Energy Conservation Standards Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

to: to: Section 141 of the Energy Policy Act of 2005 & Section 305 of the Energy Independence and Security Act of 2007 U.S. Department of Energy February 2008 Table of Contents List of Acronyms .............................................................................................................. 3 Introduction ...................................................................................................................... 4 Section 1: Backlog and EPACT 2005.............................................................................. 5 State of New York, et al. v. Bodman; and NRDC, Inc. et al. v. Bodman ...................... 5 Multi-Year Schedule and Implementation Update................................................. 7 Multi-Year Schedule ................................................................................................ 7

14

Reference Manual and Procedures for Implementation of PURPA Standards in  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EISA 2007 EISA 2007 Reference Manual and Procedures for Implementation of PURPA Standards in EISA 2007 This reference manual is intended to be used as an aid to state commissions and utilities as they consider the new federal standards that are part of the Energy Independence and Security Act of 2007 (or EISA, sections 374, 531, 532, and 1307). It summarizes state commission and unregulated utility requirements, covers implementation procedures and issues to be considered, and defines and discusses the new standards. Manual for Implementation of PURPA Standards in EISA 2007 (August 2008).pdf More Documents & Publications Reference Manual and Procedures for Implementation of PURPA Standards in EPACT 2005 (March 2006) Demand Response and Smart Metering Policy Actions Since the Energy Policy

15

Reference Manual and Procedures for Implementation of PURPA Standards in  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EPACT 2005 (March 2006) EPACT 2005 (March 2006) Reference Manual and Procedures for Implementation of PURPA Standards in EPACT 2005 (March 2006) This reference manual is intended to be used as an aid to state commissions and utilities as they consider the new federal standards that are part of the Energy Policy Act of 2005 (Subtitle E, "Amendments to PURPA," sections 1251, 1252, and 1254). It summarizes state commission and unregulated utility requirements and covers implementation procedures and issues to be considered. Manual for Implementation of PURPA Standards in EPACT 2005 (March 2006).pdf More Documents & Publications Reference Manual and Procedures for Implementation of PURPA Standards in EISA 2007 REPORT TO CONGRESS ON COMPETITION IN WHOLESALE AND RETAIL MARKETS FOR

16

2007 Implementation Report to Congress on Energy Conservation Standards Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Conservation Standards Activities Submitted Pursuant to Section 141 of the Energy Policy Act of 2005 U.S. Department of Energy August 2007 Table of Contents List of Acronyms .............................................................................................................. 3 Introduction ...................................................................................................................... 4 State of New York, et al. v. Bodman; and NRDC, Inc. et al v. Bodman ............................ 5 Multi-Year Schedule and Implementation Update..................................................... 6 Multi-Year Schedule....................................................................................................... 6 Implementation Update .................................................................................................. 9

17

Establishment, Implementation and Enforcement of Building Codes and Standards  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Establishment, Implementation and Enforcement Establishment, Implementation and Enforcement of Building Codes and Standards Nanette Lockwood Global Director Government Affairs Solutia Inc. 2 Crystex ® Solutia Inc. Advanced Interlayers Performance Films Technical Specialties 2010 Revenue $1.9 billion USD Facilities 50+ Employees 3,300 U.S. Building Codes and Standards * Developed, updated and published on regular intervals at the national level for use locally * Adopted by federal agencies, state and local governments * Typically enforced by local building departments * Applies to new construction, additions and major renovations for nearly all buildings Model Building Codes * National development committees - Architects, engineers, builders, scientists, insurers, government researchers, agencies and building officials

18

FASTBUS standard routines implementation for Fermilab embedded processor boards  

SciTech Connect

In collaboration with CEBAF, Fermilab has produced a new C implementation of the IEEE FASTBUS Standard Routines. This implementation runs under the V[sub x] Works operating system and has been ported to the PC-4 revision of the FASTBUS Smart Crate Controller (FSCC) and the FASTBUS Readout Controller (FRC). Both of these boards are used in fixed target and collider HEP experiments. Features of this implementation include: optional generation of high-speed in-line code, built-in RPC (remote procedure call) support, and a TCL (tool command language) command line interpreter interface. The authors describe this software with recent extensions to support RPC.

Votava, M.; Kent, S.; Oleynik, G.; Pordes, R.; Pangburn, J.; Patrick, J. (Fermi National Accelerator Lab., Batavia, IL (United States)); Heyes, G.; Watson, W.A. III (CEBAF, Newport News, VA (United States))

1994-02-01T23:59:59.000Z

19

Energy standards and model codes development, adoption, implementation, and enforcement  

Science Conference Proceedings (OSTI)

This report provides an overview of the energy standards and model codes process for the voluntary sector within the United States. The report was prepared by Pacific Northwest Laboratory (PNL) for the Building Energy Standards Program and is intended to be used as a primer or reference on this process. Building standards and model codes that address energy have been developed by organizations in the voluntary sector since the early 1970s. These standards and model codes provide minimum energy-efficient design and construction requirements for new buildings and, in some instances, existing buildings. The first step in the process is developing new or revising existing standards or codes. There are two overall differences between standards and codes. Energy standards are developed by a consensus process and are revised as needed. Model codes are revised on a regular annual cycle through a public hearing process. In addition to these overall differences, the specific steps in developing/revising energy standards differ from model codes. These energy standards or model codes are then available for adoption by states and local governments. Typically, energy standards are adopted by or adopted into model codes. Model codes are in turn adopted by states through either legislation or regulation. Enforcement is essential to the implementation of energy standards and model codes. Low-rise residential construction is generally evaluated for compliance at the local level, whereas state agencies tend to be more involved with other types of buildings. Low-rise residential buildings also may be more easily evaluated for compliance because the governing requirements tend to be less complex than for commercial buildings.

Conover, D.R.

1994-08-01T23:59:59.000Z

20

Implementation Report: Energy Conservation Standards Activities August 2008  

NLE Websites -- All DOE Office Websites (Extended Search)

Implementation Report: Energy Conservation Standards Activities Submitted Pursuant to: Section 141 of the Energy Policy Act of 2005 & Section 305 of the Energy Independence and Security Act of 2007 U.S. Department of Energy August 2008 Table of Contents List of Acronyms ...................................................................................................................................... 3 � Introduction .............................................................................................................................................. 4 � Backlog and EPACT 2005 ....................................................................................................................... 5 � State of New York, et al. v. Bodman; and NRDC, Inc. et al. v. Bodman ...............................................5

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Implementation Report: Energy Conservation Standards Activities August 2008  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementation Report: Energy Conservation Standards Activities Submitted Pursuant to: Section 141 of the Energy Policy Act of 2005 & Section 305 of the Energy Independence and Security Act of 2007 U.S. Department of Energy August 2008 Table of Contents List of Acronyms ...................................................................................................................................... 3 � Introduction .............................................................................................................................................. 4 � Backlog and EPACT 2005 ....................................................................................................................... 5 � State of New York, et al. v. Bodman; and NRDC, Inc. et al. v. Bodman ...............................................5

22

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network (OSTI)

Dryers NAECA 1987 Dishwashers + NAECA 1987 Refrigerators andstudy vary in how b Dishwashers, residential boilers andon clothes washers and dishwashers). g The annual savings of

Meyers, Stephen

2013-01-01T23:59:59.000Z

23

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network (OSTI)

2015/2018) Residential dishwashers ( 2013) ASHRAE products (Dryers NAECA 1987 Dishwashers NAECA 1987 Refrigerators andagainst which c Dishwashers, residential boilers and

Meyers, Stephen

2013-01-01T23:59:59.000Z

24

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network (OSTI)

Dryers NAECA 1987 Dishwashers + NAECA 1987 Refrigerators andextensively reviewed. a Dishwashers, residential boilers andon clothes washers and dishwashers). e The annual savings d

Meyers, Stephen

2013-01-01T23:59:59.000Z

25

Renewable portfolio standard: an analysis of design and implementation issues.  

E-Print Network (OSTI)

??The Renewable Portfolio Standard (RPS) is a policy tool that requires a certain percentage of renewable energy to be included in the portfolio of electricity (more)

Parvanyan, Tigran

2005-01-01T23:59:59.000Z

26

February 2009 Implementation Report: Energy Conservation Standards Activities  

NLE Websites -- All DOE Office Websites (Extended Search)

09 09 Table of Contents List of Acronyms ...................................................................................................................................... 3 Introduction .............................................................................................................................................. 4 Backlog and EPACT 2005 ....................................................................................................................... 5 State of New York, et al. v. Bodman; and NRDC, Inc. et al. v. Bodman ...............................................5 Energy Independence and Security Act of 2007.................................................................................. 7 Multi-Year Schedule and Implementation Update............................................................................. 8

27

February 2009 Implementation Report: Energy Conservation Standards Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

09 09 Table of Contents List of Acronyms ...................................................................................................................................... 3 Introduction .............................................................................................................................................. 4 Backlog and EPACT 2005 ....................................................................................................................... 5 State of New York, et al. v. Bodman; and NRDC, Inc. et al. v. Bodman ...............................................5 Energy Independence and Security Act of 2007.................................................................................. 7 Multi-Year Schedule and Implementation Update............................................................................. 8

28

Implementing device UI in standards-based markup  

Science Conference Proceedings (OSTI)

In this case study, we present initial implementations for NFDM, a technology for leveraging the mobile web browser for user interface. This study focuses on using NFDM for the idle screen application. We describe NFDM technology and present both user ... Keywords: DOM, ECMAScript, HTML, browser, markup, user interface

Daniel F. Zucker; Elizabeth Dykstra-Erickson; Michimasa Uematsu; Tomy Kamada

2006-09-01T23:59:59.000Z

29

Plant Engineering: EPRI Standardized Task Evaluation Program Implementation Guide  

Science Conference Proceedings (OSTI)

The nuclear power industry uses supplemental workers to support outages and other work activities. It is important to provide assurances that these workers are knowledgeable and skilled in the performance of the specific tasks to which they will be assigned as independent workers. The end result must be objective, credible evidence to show that the independent workers have been evaluated to meet station standards. One method of determining whether a worker is proficient ...

2012-11-14T23:59:59.000Z

30

The Second US-China Energy Efficiency Forum: Energy Management Standards and Implementation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards Standards and Implementation James Quinn U.S. Department of Energy 1 DOE's Industrial Technologies Programivers Solutions Help plants save energy today by assessing opportunities and facilitating adoption of best energy management practices Develop advanced technologies addressing the top energy savings opportunities across industry Research & Development Technical Assistance Improve national energy security, climate, environment, and economic competitiveness by transforming the way U.S. industry uses energy. 2 * Time and again, industrial energy efficiency has been demonstrated to be cost effective while having a positive effect on productivity * Despite this, energy efficiency improvements with very favorable payback periods often do not get implemented

31

Experience implementing energy standards for commercial buildings and its lessons for the Philippines  

SciTech Connect

Energy efficiency standards for buildings have been adopted in over forty countries. This policy mechanism is pursued by governments as a means of increasing energy efficiency in the buildings sector, which typically accounts for about a third of most nations' energy consumption and half of their electricity consumption. This study reports on experience with implementation of energy standards for commercial buildings in a number of countries and U.S. states. It is conducted from the perspective of providing useful input to the Government of the Philippines' (GOP) current effort at implementing their building energy standard. While the impetus for this work is technical assistance to the Philippines, the intent is to shed light on the broader issues attending implementation of building energy standards that would be applicable there and elsewhere. The background on the GOP building energy standard is presented, followed by the objectives for the study, the approach used to collect and analyze information about other jurisdictions' implementation experience, results, and conclusions and recommendations.

Busch, John; Deringer, Joseph

1998-10-01T23:59:59.000Z

32

International Review of the Development and Implementation of Energy Efficiency Standards and Labeling Programs  

SciTech Connect

Appliance energy efficiency standards and labeling (S&L) programs have been important policy tools for regulating the efficiency of energy-using products for over 40 years and continue to expand in terms of geographic and product coverage. The most common S&L programs include mandatory minimum energy performance standards (MEPS) that seek to push the market for efficient products, and energy information and endorsement labels that seek to pull the market. This study seeks to review and compare some of the earliest and most well-developed S&L programs in three countries and one region: the U.S. MEPS and ENERGY STAR, Australia MEPS and Energy Label, European Union MEPS and Ecodesign requirements and Energy Label and Japanese Top Runner programs. For each program, key elements of S&L programs are evaluated and comparative analyses across the programs undertaken to identify best practice examples of individual elements as well as cross-cutting factors for success and lessons learned in international S&L program development and implementation. The international review and comparative analysis identified several overarching themes and highlighted some common factors behind successful program elements. First, standard-setting and programmatic implementation can benefit significantly from a legal framework that stipulates a specific timeline or schedule for standard-setting and revision, product coverage and legal sanctions for non-compliance. Second, the different MEPS programs revealed similarities in targeting efficiency gains that are technically feasible and economically justified as the principle for choosing a standard level, in many cases at a level that no product on the current market could reach. Third, detailed survey data such as the U.S. Residential Energy Consumption Survey (RECS) and rigorous analyses provide a strong foundation for standard-setting while incorporating the participation of different groups of stakeholders further strengthen the process. Fourth, sufficient program resources for program implementation and evaluation are critical to the effectiveness of standards and labeling programs and cost-sharing between national and local governments can help ensure adequate resources and uniform implementation. Lastly, check-testing and punitive measures are important forms of enforcement while the cancellation of registration or product sales-based fines have also proven effective in reducing non-compliance. The international comparative analysis also revealed the differing degree to which the level of government decentralization has influenced S&L programs and while no single country has best practices in all elements of standards and labeling development and implementation, national examples of best practices for specific elements do exist. For example, the U.S. has exemplified the use of rigorous analyses for standard-setting and robust data source with the RECS database while Japan?s Top Runner standard-setting principle has motivated manufacturers to exceed targets. In terms of standards implementation and enforcement, Australia has demonstrated success with enforcement given its long history of check-testing and enforcement initiatives while mandatory information-sharing between EU jurisdictions on compliance results is another important enforcement mechanism. These examples show that it is important to evaluate not only the drivers of different paths of standards and labeling development, but also the country-specific context for best practice examples in order to understand how and why certain elements of specific S&L programs have been effective.

Zhou, Nan; Zheng, Nina; Fridley, David

2012-02-28T23:59:59.000Z

33

Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience  

NLE Websites -- All DOE Office Websites (Extended Search)

Including Alternative Resources Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience Jenny Heeter and Lori Bird Technical Report NREL/TP-6A20-55979 November 2012 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 15013 Denver West Parkway Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience Jenny Heeter and Lori Bird Prepared under Task No. SAO9.3110

34

Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience  

SciTech Connect

Currently, 29 states, the District of Columbia, and Puerto Rico have instituted a renewable portfolio standard (RPS). An RPS sets a minimum threshold for how much renewable energy must be generated in a given year. Each state policy is unique, varying in percentage targets, timetables, and eligible resources. This paper examines state experience with implementing renewable portfolio standards that include energy efficiency, thermal resources, and non-renewable energy and explores compliance experience, costs, and how states evaluate, measure, and verify energy efficiency and convert thermal energy. It aims to gain insights from the experience of states for possible federal clean energy policy as well as to share experience and lessons for state RPS implementation.

Heeter, J.; Bird, L.

2012-11-01T23:59:59.000Z

35

Interim implementation structure for development of performance criteria and test standards for photovoltaic systems  

DOE Green Energy (OSTI)

This document presents an implementation structure for the near-term development of performance criteria and test methods for photovoltaic (PV) materials, components, subsystems, and systems. The approach is designed to be responsive to the Photovoltaic Research, Development and Demonstration Act of 1978 (PL-95-590). The project is organized into four tasks: (1) establishment of performance criteria and the development of test methods; (2) development of laboratory accreditation/product certification guidelines; (3) development of validation methodologies; and (4) coordination of the quality assurance effort with consensus standards and code organizations. A schedule and milestones are presented for each task. The appendices provide a brief overview of standards and the standards development process. The philosophy behind this project is to develop industry- and user-established performance criteria, test methods, and accreditation procedures which may then be referred to independent consensus standards organizations for the preparation of consensus standards. The emphasis in execution of this approach will be to develop uniform, fair performance criteria and tests and to avoid rigid, prescriptive criteria. Photovoltaics is an emerging technology; criteria written now must be able to accommodate devices and techniques not yet developed.

Not Available

1979-11-15T23:59:59.000Z

36

Renewable Portfolio Standards in the States: Balancing Goals and Implementation Strategies  

SciTech Connect

This paper reports on renewable portfolio standards (RPS) and how the RPS rules vary from state to state. This variation presents important challenges to successful implementation. Key issues are discussed in terms of resource availability, solar-specific provisions, and political and regulatory consistency, and their impacts on the ability to finance new renewable energy projects. This report emphasizes the fact that a successful RPS policy must balance a state's goals for fuel diversity, economic development, price effects, and environmental benefits.

Cory, K. S.; Swezey, B. G.

2007-12-01T23:59:59.000Z

37

Implementing an integrated standards-based management system to ensure compliance at Los Alamos National Laboratory  

SciTech Connect

Los Alamos National Laboratory (LANL or the Laboratory) is developing and implementing a comprehensive, Integrated Standards-Based Management System (ISBMS) to enhance environmental, safety, and health (ESH) compliance efforts and streamline management of ESH throughout the Laboratory. The Laboratory recognizes that to be competitive in today`s business environment and attractive to potential Partnerships, Laboratory operations must be efficient and cost-effective. The Laboratory also realizes potential growth opportunities for developing ESH as a strength in providing new or improved services to its customers. Overall, the Laboratory desires to establish and build upon an ESH management system which ensures continuous improvement in protecting public health and safety and the environment and which fosters a working relationship with stakeholders. A team of process experts from the LANL Environmental Management (EM) Program Office, worked with management system consultants, and the Department of Energy (DOE) to develop an ESH management systems process to compare current LANL ESH management Systems and programs against leading industry standards. The process enabled the Laboratory to gauge its performance in each of the following areas: Planning and Policy Setting; Systems and Procedures; Implementation and Education; and Monitoring and Reporting. The information gathered on ESH management systems enabled LANL to pinpoint and prioritize opportunities for improvement in the provision of ESH services throughout the Laboratory and ultimately overall ESH compliance.

Hjeresen, D.; Roybal, S.; Bertino, P.; Gherman, C.; Hosteny, B.

1995-03-01T23:59:59.000Z

38

standards  

Science Conference Proceedings (OSTI)

... About Circular A-119About Us. Standards. Definition of Standards. Finding Standards. Information on Biometrics Standards.

2012-12-13T23:59:59.000Z

39

Implementation of ITU-T V.90 standard PCM modem in TMS320C6201 digital signal processor  

E-Print Network (OSTI)

In this thesis work, the basic functionality of a ITU-T Standard V.90 modem is implemented in a TMS320C6201 Digital Signal Processor (DSP). The encoder, equalizer and decoder functions of a V.90 modem are programmed in the DSP using C language. The program has been written to analyze the performance of the modem functions using standard algorithms. The standard V.90 modulus encoder and an easy but effective constellation selection technique have been implemented. In the receiver side, two different equalization techniques are implemented and their performance in the DSP is compared. The cycle timing of the functions has been benchmarked. The pseudo real-time implementation for the equalizers shows significant functional aspects of the equalizer. The real-time observation technique showed that the RLS equalization algorithm performance was much better than the simple LMS approach.

Molla, Shahedolla Mohammed

2001-01-01T23:59:59.000Z

40

International Review of the Development and Implementation of Energy Efficiency Standards and Labeling Programs  

E-Print Network (OSTI)

at the Asian Energy Efficiency Standards and Labeling Forum.Efficiency Labels and Standards: A Guidebook for Appliances,Labeling and Appliance Standards Program (CLASP). Wilkenfeld

Zhou, Nan

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Regulatory Perspective on Implementation of a Dose Standard for a One-Million Year Compliance Period  

Science Conference Proceedings (OSTI)

The disposal of high-level radioactive wastes in a potential geologic repository at Yucca Mountain, Nevada is governed by the U.S. Environmental Protection Agency (EPA) standards and U.S. Nuclear Regulatory Commission (NRC) regulations. The EPA has the responsibility for setting public health and safety and environmental standards for radioactive waste disposal at Yucca Mountain and it is the NRC's responsibility to implement those standards in its regulations to ensure public health and safety and the environment are protected. The U.S. Department of Energy (DOE), as the developer of the potential repository, must submit a license application to the NRC to seek approval to construct the repository. DOE must comply with NRC's regulations for NRC to authorize construction and license operation of a potential repository at Yucca Mountain. In 2005, EPA issued proposed revised standards and NRC issued proposed revised regulations for conducting performance assessment beyond 10,000 years up to 1 million years. The challenge for the EPA and NRC is to develop standards and regulations that provide an appropriate method for evaluating the safety of the potential repository given the unprecedented time period to be analyzed and the inherent uncertainties in estimating the future evolution of the Yucca Mountain site and the containment of the waste in the waste packages. A fundamental aspect of the proposed EPA standard is the specified approach for limiting undue speculation on future behavior of the site by constraining the features, events, and processes that need to be considered in the performance assessment. EPA proposed to limit the assessment of specific features, events, and processes in the period after 10,000 years to effects on the repository system that are most relevant (i.e., ignoring lesser or secondary effects that may add to speculation and uncertainties but would not be expected to have a significant effect on peak dose over a 1 million year period). For example, DOE's performance assessment may (1) limit the analysis of seismic activity to the effects caused by damage to the drifts and the waste package; (2) limit analysis of igneous activity to effects on the waste package that result in release of radionuclides to the atmosphere or ground water; (3) require DOE to include general corrosion in its analysis of engineered barrier performance, and (4) limit the effect of climate variation to those resulting from increased water flowing to the repository. NRC has been reviewing its performance assessment models and techniques to assure they are consistent with EPA's proposed requirements for the period after 10,000 years and adequate to assist the review of a potential license application from the DOE. Currently, only slight modifications to the models and approaches used in the performance assessment for the initial 10,000 years are expected to be needed to accommodate calculations for longer times (e.g., modifications to implement a steady-state value to represent the proposed climate change). NRC staff will be able to use the modified performance assessment to identify additional sensitivities associated with estimating doses over very long time periods and improve its understanding of the performance of a potential repository at Yucca Mountain. (author)

McCartin, Timothy [HLW Repository Safety, U.S. Nuclear Reg. Commission, Two White Flint North, 11545 Rockville Pike, Rockville, MD, 20852 - 2738 (United States)

2007-07-01T23:59:59.000Z

42

Fourteenth Semi-Annual Report to Congress on Appliance Energy Efficiency Rulemakings … Implementation Report: Energy Conservation Standards Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Washington, DC 20585 Message from the Assistant Secretary I am pleased to provide you with the semi-annual Implementation Report on Energy Conservation Standards Activities of the U.S. Department of Energy (DOE). This report meets the requirements of Section 141 of the Energy Policy Act of 2005 (EPACT 2005) and Section 305 of the Energy Independence and Security Act of 2007 (EISA 2007). Because the reporting intervals and requirements are similar for the EPACT 2005 and EISA 2007 reports, DOE provides a consolidated report. DOE is required by EPACT 2005 and EISA 2007 to provide semi-annual implementation reports pertaining to the DOE's deadlines for issuance of new or amended energy conservation standards. The implementation reports include a summary of DOE's progress relative to an

43

A status report on the design and implementation of state renewable portfolio standards and system benefits charge policies  

DOE Green Energy (OSTI)

At last year's Windpower conference, we reported on state policies to foster renewable energy as part of efforts to restructure state electric power markets. The primary policies states are pursuing for renewables are system benefits charges (SBC) and renewable portfolio standards (RPS). Renewable portfolio standard policies began taking effect this year, while other states are continuing to work on the design of their RPS implementation strategies. In addition, states have begun distributing proceeds from their SBC funds. As a result, some renewable energy projects are beginning to materialize. This paper provides an update on state efforts with these two policies and examines some of the implementation issues and difficulties that states have faced thus far.

Porter, K.; Wiser, R.

2000-05-01T23:59:59.000Z

44

Guidelines for Implementing Substation Automation Using IEC61850, the International Power System Information Modeling Standard  

Science Conference Proceedings (OSTI)

This report provides guidelines for substation planners, project managers, substation engineers, information technologists, and substation integrators on informational issues related to substation automation (SA) when IEC61850 standards are used.

2004-12-22T23:59:59.000Z

45

National Energy Efficiency Evaluation, Measurement and Verification (EM&V) Standard: Scoping Study of Issues and Implementation Requirements  

Science Conference Proceedings (OSTI)

This report is a scoping study that identifies issues associated with developing a national evaluation, measurement and verification (EM&V) standard for end-use, non-transportation, energy efficiency activities. The objectives of this study are to identify the scope of such a standard and define EM&V requirements and issues that will need to be addressed in a standard. To explore these issues, we provide and discuss: (1) a set of definitions applicable to an EM&V standard; (2) a literature review of existing guidelines, standards, and 'initiatives' relating to EM&V standards as well as a review of 'bottom-up' versus 'top-down' evaluation approaches; (3) a summary of EM&V related provisions of two recent federal legislative proposals (Congressman Waxman's and Markey's American Clean Energy and Security Act of 2009 and Senator Bingaman's American Clean Energy Leadership Act of 2009) that include national efficiency resource requirements; (4) an annotated list of issues that that are likely to be central to, and need to be considered when, developing a national EM&V standard; and (5) a discussion of the implications of such issues. There are three primary reasons for developing a national efficiency EM&V standard. First, some policy makers, regulators and practitioners believe that a national standard would streamline EM&V implementation, reduce costs and complexity, and improve comparability of results across jurisdictions; although there are benefits associated with each jurisdiction setting its own EM&V requirements based on their specific portfolio and evaluation budgets and objectives. Secondly, if energy efficiency is determined by the US Environmental Protection Agency to be a Best Available Control Technology (BACT) for avoiding criteria pollutant and/or greenhouse gas emissions, then a standard can be required for documenting the emission reductions resulting from efficiency actions. The third reason for a national EM&V standard is that such a standard is likely to be required as a result of future federal energy legislation that includes end-use energy efficiency, either as a stand-alone energy-efficiency resource standard (EERS) or as part of a clean energy or renewable energy standard. This study is focused primarily on this third reason and thus explores issues associated with a national EM&V standard if energy efficiency is a qualifying resource in federal clean energy legislation. Developing a national EM&V standard is likely to be a lengthy process; this study focuses on the critical first step of identifying the issues that must be addressed in a future standard. Perhaps the most fundamental of these issues is 'how good is good enough?' This has always been the fundamental issue of EM&V for energy efficiency and is a result of the counter-factual nature of efficiency. Counter-factual in that savings are not measured, but estimated to varying degrees of accuracy by comparing energy consumption after a project (program) is implemented with what is assumed to have been the consumption of energy in the absence of the project (program). Therefore, the how good is good enough question is a short version of asking how certain does one have to be of the energy savings estimate that results from EM&V activities and is that level of certainty properly balanced against the amount of effort (resources, time, money) that is utilized to obtain that level of certainty. The implication is that not only should energy efficiency investments be cost-effective, but EM&V investments should consider risk management principles and thus also balance the costs and value of information derived from EM&V (EM&V should also be cost-effective).

Schiller Consulting, Inc.; Schiller, Steven R.; Goldman, Charles A.; Galawish, Elsia

2011-02-04T23:59:59.000Z

46

TrAgLor, an implementation of IEEE LOM draft standard in agriculture and life sciences  

Science Conference Proceedings (OSTI)

The Turkish Agricultural Learning Objects Repository (TrAgLor) is a multilingual IEEE LOM Draft Standard compatible Learning Objects (LO) repository. It has been developed as a test-bed to enable the storage, search and retrieval ... Keywords: LOM, Turkey, agricultural metadata, agriculture, e-learning, electronic learning, environmental sciences, food sciences, interoperability, learning object metadata, learning objects, learning repositories, online learning, searching, veterinary sciences

Zeynel Cebeci; Yoldas Erdogan; Murat Kara

2009-05-01T23:59:59.000Z

47

13th Semi-annual Implementation Report on Energy Conservation Standards Activities of the U.S. Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Activities Report to Congress February 2013 United States Department of Energy Washington, DC 20585 Message from the Assistant Secretary I am pleased to provide you with the semi-annual Implementation Report on Energy Conservation Standards Activities of the U.S. Department of Energy (DOE). This report meets the requirements of Section 141 of the Energy Policy Act of 2005 (EPACT 2005) and Section 305 of the Energy Independence and Security Act of 2007 (EISA 2007). Because the reporting intervals and requirements are similar for the EPACT 2005 and EISA 2007 reports, DOE provides a consolidated report. DOE is required by EPACT 2005 and EISA 2007 to provide semi-annual implementation reports pertaining to the DOE's deadlines for issuance of new or amended energy conservation

48

13th Semi-annual Implementation Report on Energy Conservation Standards Activities of the U.S. Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Activities Report to Congress February 2013 United States Department of Energy Washington, DC 20585 Message from the Assistant Secretary I am pleased to provide you with the semi-annual Implementation Report on Energy Conservation Standards Activities of the U.S. Department of Energy (DOE). This report meets the requirements of Section 141 of the Energy Policy Act of 2005 (EPACT 2005) and Section 305 of the Energy Independence and Security Act of 2007 (EISA 2007). Because the reporting intervals and requirements are similar for the EPACT 2005 and EISA 2007 reports, DOE provides a consolidated report. DOE is required by EPACT 2005 and EISA 2007 to provide semi-annual implementation reports pertaining to the DOE's deadlines for issuance of new or amended energy conservation

49

Standard  

NLE Websites -- All DOE Office Websites (Extended Search)

Standard Standard rock For at least two generations, the depth of underground muon experiments has been reduced to depth in "standard rock." This is by definition the overburden of the Cayuga Rock Salt Mine near Ithaca, New York, where K. Greisen and collaborators made seminal observations of muons at substantial depths[1]. Ref. 1 says only "Most of the ground consists of shales of various types, with average density 2.65 g/cm 2 and average atomic number 11." Menon and Murthy later extended the definition: Z 2 /A = 5.5, Z/A = 0.5, and and ρ = 2.65 g/cm 2 [2]. It was thus not-quite-sodium. Lohmann[3] further assumed the mean excitation energy and density effect parameters were those of calcium carbonate, with no adjustments for the slight density difference. We use their definition for this most important material. (Extracted from D.E. Groom, N.V. Mokhov, and S.I. Striganov,

50

National Energy Efficiency Evaluation, Measurement and Verification (EM&V) Standard: Scoping Study of Issues and Implementation Requirements  

E-Print Network (OSTI)

Actuarial Pricing Of Energy Efficiency Projects: Lessonsand Effectiveness of Energy Efficiency Programs, LBNL-ACEEE 2010. State Energy Efficiency Resource Standard (

Schiller, Steven R.

2011-01-01T23:59:59.000Z

51

Creating and Implementing a Regularized Monitoring and Enforcement System for China's Mandatory Standards and Energy Information Label for Appliances  

E-Print Network (OSTI)

Information Label for Appliances Author: Jiang Lin MarchBasic Structure of Chinas Appliance Standards and Labelingbasic infrastructure for appliance performance testing is in

Lin, Jiang

2008-01-01T23:59:59.000Z

52

A test and validation approach for the standard-based implementation of intelligent electronic devices in smart grids  

Science Conference Proceedings (OSTI)

Availability and functionality of reliable and efficient electric energy systems are pre-requisites for economic and social welfare. The continuous growth of electric energy consumption as well as the upcoming large-scale integration of distributed and ... Keywords: IEC 61499, IEC 61850, controller-hardware-in-the-Loop (CHIL), distributed intelligent control, intelligent electronic device (IED), simulation, smart grids, standards

Thomas Strasser; Filip Andren; Matthias Stifter

2011-08-01T23:59:59.000Z

53

Creating and Implementing a Regularized Monitoring and EnforcementSystem for China's Mandatory Standards and Energy Information Label forAppliances  

SciTech Connect

China has developed a comprehensive program of energy efficiency standards and labels for household appliances. In 1989, China first launched its minimum energy performance standards (MEPS), which are now applied to an extensive list of products. In 1998, China launched a voluntary energy endorsement label, which has grown to cover both energy-saving and water-saving products. And, in 2005, China launched a mandatory energy information label that initially covered two products. CLASP has assisted China in developing 11 minimum energy performance standards (MEPS) for 9 products and endorsement labels for 11 products including: refrigerators; air conditioners; televisions; printers; computers; monitors; fax machines; copiers; DVD/VCD players; external power supplies; and set-top boxes. CLASP has also assisted China in the development of the mandatory energy information label. Increasingly, attention is being placed on maximum energy savings from China's standards and labeling (S&L) efforts in order to meet the recently announced goal of reducing China's energy intensity by 20 percent by 2010 with an interim objective of 4 percent in 2006. China's mandatory standards system is heavily focused on the technical requirements for efficiency performance, but historically, it has lacked administrative and personnel capacity to undertake monitoring and enforcement of these legally binding standards. Similarly, resources for monitoring and enforcement have been quite limited. As a consequence, compliance to both the mandatory standards and the mandatory energy information label is uneven with the potential and likely result of lost energy savings. Thus, a major area for improvement, which could significantly increase overall energy savings, is the creation and implementation of a regularized monitoring system for tracking the compliance to, and enforcement of, mandatory standards and the energy information label in China. CLASP has been working with the China National Institute of Standardization (CNIS), the China Administration for Quality, Supervision, Inspection and Quarantine (AQSIQ) and relevant stakeholders in the industry to develop a stronger system of monitoring and enforcement. In November 2005, CNIS and LBNL (a CLASP implementing partner) with funding from the Energy Foundation jointly organized an international workshop to present the international best practices in S&L monitoring and enforcement. Currently, CNIS is developing a guideline for monitoring and enforcement for appliance standards. With support from METI, CLASP has been able to expand the on-going collaboration with CNIS to include enforcement needs for the mandatory energy information label and to accelerate the progress of the project to develop a more robust monitoring and enforcement for S&L programs in China. This expanded effort has included: (1) Holding an enforcement and monitoring roadmap planning workshop with key S&L stakeholders; (2) Interviews with S&L stakeholders on the need and scope of national compliance tests; (3) Research on past enforcement activities; (4) An analysis of compliance data from the mandatory energy information labeling program; (5) Interviews with stakeholders on the need and scope of testing infrastructure; and (6) Development of a roadmap for future activities. This report summarizes the findings of these activities and identifies the progress that China is making, and can make, toward developing a stronger system of monitoring and enforcement (M&E). In sum, it outlines a vision of moving forward with more vigorous M&E in China.

Lin, Jiang

2007-03-01T23:59:59.000Z

54

DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Act (NAECA), prescribes energy conservation standards for certain major household appliances, and requires the Department of Energy (DOE) to administer an energy...

55

Wireless System Considerations When Implementing NERC Critical...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wireless System Considerations When Implementing NERC Critical Infrastructure Protection Standards Wireless System Considerations When Implementing NERC Critical Infrastructure...

56

Realized and Projected Impacts of U.S. Energy Efficiency Standards for Residential and Commercial Appliances  

SciTech Connect

This study estimated energy, environmental and consumer economic impacts of U.S. Federal residential energy efficiency standards that became effective in the 1988-2006 period, and of energy efficiency standards for fluorescent lamp ballasts and distribution transformers. These standards have been the subject of in-depth analyses conducted as part of DOE's standards rulemaking process. This study drew on those analyses, but updated certain data and developed a common framework and assumptions for all of the products in order to estimate realized impacts and to update projected impacts. It also performed new analysis for the first (1990) fluorescent ballast standards, which had been introduced in the NAECA legislation without a rulemaking. We estimate that the considered standards will reduce residential/ commercial primary energy consumption and carbon dioxide emissions in 2030 by 4percent compared to the levels expected without any standards. The reduction for the residential sector is larger, at 8percent. The estimated cumulative energy savings from the standards amount to 39 quads by 2020, and 63 quads by 2030. The standards will also reduce emissions of carbon dioxide by considerable amounts.The estimated cumulative net present value of consumer benefit amounts to $241 billion by 2030, and grows to $269 billion by 2045. The overall ratio of consumer benefits to costs (in present value terms) in the 1987-2050 period is 2.7 to 1. Although the estimates made in this study are subject to a fair degree of uncertainty, we believe they provide a reasonable approximation of the national benefits resulting from Federal appliance efficiency standards.

Meyers, Stephen P.; McMahon, James; Atkinson, Barbara

2008-05-08T23:59:59.000Z

57

Realized and Projected Impacts of U.S. Energy Efficiency Standards for Residential and Commercial Appliances  

SciTech Connect

This study estimated energy, environmental and consumer economic impacts of U.S. Federal residential energy efficiency standards that became effective in the 1988-2006 period, and of energy efficiency standards for fluorescent lamp ballasts and distribution transformers. These standards have been the subject of in-depth analyses conducted as part of DOE's standards rulemaking process. This study drew on those analyses, but updated certain data and developed a common framework and assumptions for all of the products in order to estimate realized impacts and to update projected impacts. It also performed new analysis for the first (1990) fluorescent ballast standards, which had been introduced in the NAECA legislation without a rulemaking. We estimate that the considered standards will reduce residential/ commercial primary energy consumption and carbon dioxide emissions in 2030 by 4percent compared to the levels expected without any standards. The reduction for the residential sector is larger, at 8percent. The estimated cumulative energy savings from the standards amount to 39 quads by 2020, and 63 quads by 2030. The standards will also reduce emissions of carbon dioxide by considerable amounts.The estimated cumulative net present value of consumer benefit amounts to $241 billion by 2030, and grows to $269 billion by 2045. The overall ratio of consumer benefits to costs (in present value terms) in the 1987-2050 period is 2.7 to 1. Although the estimates made in this study are subject to a fair degree of uncertainty, we believe they provide a reasonable approximation of the national benefits resulting from Federal appliance efficiency standards.

Meyers, Stephen P.; McMahon, James; Atkinson, Barbara

2008-05-08T23:59:59.000Z

58

National Emission Standards for Hazardous Air Pollutants for Major Sources: Industrial, Commercial, and Institutional Boilers; Guidance for Calculating Efficiency Credits Resulting from Implementation of Energy Conservation Measures  

Science Conference Proceedings (OSTI)

The purpose of this document is to provide guidance for developing a consistent approach to documenting efficiency credits generated from energy conservation measures in the Implementation Plan for boilers covered by the Boiler MACT rule (i.e., subpart DDDDD of CFR part 63). This document divides Boiler System conservation opportunities into four functional areas: 1) the boiler itself, 2) the condensate recovery system, 3) the distribution system, and 4) the end uses of the steam. This document provides technical information for documenting emissions credits proposed in the Implementation Plan for functional areas 2) though 4). This document does not include efficiency improvements related to the Boiler tune-ups.

Cox, Daryl [ORNL; Papar, Riyaz [Hudson Technologies; Wright, Dr. Anthony [ALW Consulting

2013-02-01T23:59:59.000Z

59

National Emission Standards for Hazardous Air Pollutants for Major Sources: Industrial, Commercial, and Institutional Boilers; Guidance for Calculating Emission Credits Resulting from Implementation of Energy Conservation Measures  

Science Conference Proceedings (OSTI)

The purpose of this document is to provide guidance for developing a consistent approach to documenting efficiency credits generated from energy conservation measures in the Implementation Plan for boilers covered by the Boiler MACT rule (i.e., subpart DDDDD of CFR part 63). This document divides Boiler System conservation opportunities into four functional areas: 1) the boiler itself, 2) the condensate recovery system, 3) the distribution system, and 4) the end uses of the steam. This document provides technical information for documenting emissions credits proposed in the Implementation Plan for functional areas 2) though 4). This document does not include efficiency improvements related to the Boiler tune-ups.

Cox, Daryl [ORNL; Papar, Riyaz [Hudson Technologies; Wright, Dr. Anthony [ALW Consulting

2012-07-01T23:59:59.000Z

60

analysis model for selection of consensus standards  

Science Conference Proceedings (OSTI)

... different vendors? Implementations? Legal considerations. Are there any patent assertions made to this standard? Are there ...

2013-03-28T23:59:59.000Z

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Alabama Compliance Implementation  

NLE Websites -- All DOE Office Websites (Extended Search)

Alabama Alabama Compliance Implementation and Evaluation (CIE) Guide BUILDING TECHNOLOGIES PROGRAM COMPLIANCE IMPLEMENTATION AND EVALUATION (CIE) GUIDE 2 This Guide is designed to assist state and local code jurisdictions in achieving statewide compliance with the 2009 International Energy Conservation Code (IECC) for residential buildings and ANSI/ASHRAE/IESNA Standard 90.1-2007 for commercial buildings. COMPLIANCE IMPLEMENTATION AND EVALUATION (CIE) GUIDE 3 Alabama WHAT'S INSIDE CIE Guide Overview-Flow Diagram ........................................................................................................................... 5 PART 1: Guide Overview .................................................................................................................................................

62

Building Technologies Office: Implementation, Certification and Enforcement  

NLE Websites -- All DOE Office Websites (Extended Search)

Implementation, Implementation, Certification and Enforcement to someone by E-mail Share Building Technologies Office: Implementation, Certification and Enforcement on Facebook Tweet about Building Technologies Office: Implementation, Certification and Enforcement on Twitter Bookmark Building Technologies Office: Implementation, Certification and Enforcement on Google Bookmark Building Technologies Office: Implementation, Certification and Enforcement on Delicious Rank Building Technologies Office: Implementation, Certification and Enforcement on Digg Find More places to share Building Technologies Office: Implementation, Certification and Enforcement on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement Standardized Templates for Reporting Test Results

63

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

that are used for space conditioning of commercial and industrial buildings. The standards implemented in 2010 for small and large, air-cooled commercial package air...

64

CPRA Implementation  

U.S. Energy Information Administration (EIA)

CPRA IMPLEMENTATION. Since the 1930s Louisiana has lost over 1,829 square miles of land. Between 1990 and 2001 wetland loss was approximately 13 ...

65

Building Technologies Program: About Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

About Standards to About Standards to someone by E-mail Share Building Technologies Program: About Standards on Facebook Tweet about Building Technologies Program: About Standards on Twitter Bookmark Building Technologies Program: About Standards on Google Bookmark Building Technologies Program: About Standards on Delicious Rank Building Technologies Program: About Standards on Digg Find More places to share Building Technologies Program: About Standards on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement Rulemakings & Notices Further Guidance ENERGY STAR® Popular Links Success Stories Previous Next Lighten Energy Loads with System Design. Learn More. Warming Up to Pump Heat. Learn More. Cut Refrigerator Energy Use to Save Money. Learn More.

66

Environmental protection implementation plan  

SciTech Connect

This Environmental Protection Implementation Plan is intended to ensure that the environmental program objectives of Department of Energy Order 5400.1 are achieved at SNL/California. This document states SNL/California`s commitment to conduct its operations in an environmentally safe and responsible manner. The Environmental Protection Implementation Plan helps management and staff comply with applicable environmental responsibilities. SNL is committed to operating in full compliance with the letter and spirit of applicable environmental laws, regulations, and standards. Furthermore, SNL/California strives to go beyond compliance with legal requirements by making every effort practical to reduce impacts to the environment to levels as low as reasonably achievable.

Holland, R.C.

1998-03-01T23:59:59.000Z

67

Wireless System Considerations When Implementing NERC Critical  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wireless System Considerations When Implementing NERC Critical Wireless System Considerations When Implementing NERC Critical Infrastructure Protection Standards Wireless System Considerations When Implementing NERC Critical Infrastructure Protection Standards Energy asset owners are facing a monumental challenge as they address compliance with the North American Electric Reliability Corporation (NERC) Critical Infrastructure Protection (CIP) Standards (CIP-002 through CIP-009). The increased use of wireless technologies and their introduction into control center networks and field devices compound this challenge, as ambiguity exists regarding the applicability of the CIP requirements to wireless networking technologies. Wireless System Considerations When Implementing NERC Critical Infrastructure Protection Standards More Documents & Publications

68

Fusion Implementation  

SciTech Connect

If a fusion DEMO reactor can be brought into operation during the first half of this century, fusion power production can have a significant impact on carbon dioxide production during the latter half of the century. An assessment of fusion implementation scenarios shows that the resource demands and waste production associated with these scenarios are manageable factors. If fusion is implemented during the latter half of this century it will be one element of a portfolio of (hopefully) carbon dioxide limiting sources of electrical power. It is time to assess the regional implications of fusion power implementation. An important attribute of fusion power is the wide range of possible regions of the country, or countries in the world, where power plants can be located. Unlike most renewable energy options, fusion energy will function within a local distribution system and not require costly, and difficult, long distance transmission systems. For example, the East Coast of the United States is a prime candidate for fusion power deployment by virtue of its distance from renewable energy sources. As fossil fuels become less and less available as an energy option, the transmission of energy across bodies of water will become very expensive. On a global scale, fusion power will be particularly attractive for regions separated from sources of renewable energy by oceans.

J.A. Schmidt

2002-02-20T23:59:59.000Z

69

Standards for ICCP API  

Science Conference Proceedings (OSTI)

The Inter-Control Center Communication Protocol (ICCP) was developed as an EPRI project for the exchange of power system information between control centers, or between a control center and a generation control system or substation. ICCP is now an international standard, IEC 60870-6 known as Telecontrol Application Service Element 2 (TASE.2). However, the application program interface (API) was not a part of that standard and was left as a "local implementation issue" for each ICCP vendor to define. The ...

1999-12-10T23:59:59.000Z

70

Standards, Ethics  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards, Ethics Ombuds Standards and Ethics Committed to the fair and equitable treatment of all employees, contractors, and persons doing business with the Laboratory. Contact...

71

Find Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

may not be available from IHS: AHRI standards - from the Air Conditioning, Heating, and Refrigeration Institute AISC standards - from the American Institute of Steel Construction...

72

The Standards Forum, February 1996  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards Forum Volume 4, Number 2 - September 1996 The Standards News on the DOE Technical Standards Program Forum Volume 4. Number 2 - September 1996 Implementation of the National Technology Transfer and Advancement Act of 1995 (Public Law 104-113) Work continues within the Technical Standards Program Office (TSPO) supporting the implementation of Public Law (PL) 104-113. Activities in progress include the following: 1. The TSPO is developing revisions to the Technical Standards Program Procedures (TSPPs) to reference PL 104-113 and strengthen the project screening process (TSPP-2) to promote development of volun- tary standards in lieu of DOE technical standards. The proposed TSPP revisions will be submitted to the Technical Standards Managers' Committee (TSMC) for

73

Strategic Standardization  

Science Conference Proceedings (OSTI)

... Program Strategic Standardization Curriculum (CMGT 564 - 2010) ... com. Curriculum ks eport, 1992), Grading (Research paper, ...

2012-12-03T23:59:59.000Z

74

Hardness Standardization  

Science Conference Proceedings (OSTI)

... metallic products. NIST produces a variety of hardness Standard Reference Materials (SRMs) for industry. The NIST ...

2013-08-20T23:59:59.000Z

75

An energy standard for residential buildings in south China  

E-Print Network (OSTI)

Abstract: residential, buildings, energy standard, energyspiraling demand for building energy use, Chinas Ministryand implementing building energy standards, starting with a

Huang, Yu Joe; Lang, Siwei; Hogan, John; Lin, Haiyan

2003-01-01T23:59:59.000Z

76

EIA - AEO2010 - CAFE standards  

Annual Energy Outlook 2012 (EIA)

economy requirement of 34.1 mpg by 2016. Because the CO2-equivalent standards cover all vehicle emissions related to GHGs, manufacturers who do not implement technologies that...

77

Earthjustice, Appliance Standards Awareness Project, Natural...  

NLE Websites -- All DOE Office Websites (Extended Search)

Earthjustice, Appliance Standards Awareness Project, Natural Resources Defense Council - Comments in response to DOE solicitation of views on the implementation of test procedure...

78

Appliance Efficiency Standards (Massachusetts) | Open Energy...  

Open Energy Info (EERE)

standards Implementing Agency MA Department of Energy Resources Review Biannual report Test Methods Massachusetts plumbing code or U.S. Department of Energy approved test methods...

79

March-April 2009 Standards Forum and Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

March/April 2009 U.S. Department of Energy Technical Standards Program (http://www.hss.energy.gov/nuclearsafety/ns/techstds/) The Standards Forum And Standards Actions Technical Standards Program Manager's Note Welcome to the March/April 2009 edition of the Technical Standards Forum and Standards Actions. The Department of Energy (DOE) Technical Standards Program (TSP) continues to provide timely and efficient standards development services to the Department and its contractors. Recently, the TSP acquired the ability to perform title and abstract searches on Non-Government Standards (NGS) available in the private sector. This tool enables the TSP and its customers to identify available NGS that could support implementation of DOE requirements. Office of Management and Budget Circular No.

80

A MIPS R2000 implementation  

Science Conference Proceedings (OSTI)

Thirty-four undergraduates implemented a MIPS R2000 processor for an introductory CMOS VLSI design course. This included designing a microarchitecture in Verilog, developing custom PLA generation and ad-hoc random testing tools, creating a standard cell ... Keywords: MIPS, RISC

Nathaniel Pinckney; Thomas Barr; Michael Dayringer; Matthew McKnett; Nan Jiang; Carl Nygaard; David Money Harris; Joel Stanley; Braden Phillips

2008-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Building Technologies Office: Standards and Test Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards and Test Standards and Test Procedures to someone by E-mail Share Building Technologies Office: Standards and Test Procedures on Facebook Tweet about Building Technologies Office: Standards and Test Procedures on Twitter Bookmark Building Technologies Office: Standards and Test Procedures on Google Bookmark Building Technologies Office: Standards and Test Procedures on Delicious Rank Building Technologies Office: Standards and Test Procedures on Digg Find More places to share Building Technologies Office: Standards and Test Procedures on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement Rulemakings & Notices Further Guidance ENERGY STAR® Popular Links Success Stories Previous Next Lighten Energy Loads with System Design. Learn More.

82

WELDING STANDARDS  

SciTech Connect

Hanford Atomic Production Operation specification guides and standards for welding and brazing are presented. Details of this manual are given in TID- 4100 (Suppl.). (N.W.R.)

1963-01-01T23:59:59.000Z

83

Parabolic cylinder functions implemented in Matlab  

E-Print Network (OSTI)

Routines for computation of Weber's parabolic cylinder functions and their derivatives are implemented in Matlab for both moderate and great values of the argument. Standard, real solutions are considered. Tables of values are included.

E. Cojocaru

2009-01-15T23:59:59.000Z

84

Does It Have To Be This Hard? Implementing the Nation's Most...  

NLE Websites -- All DOE Office Websites (Extended Search)

Have To Be This Hard? Implementing the Nation's Most Aggressive Renewables Portfolio Standard in California Title Does It Have To Be This Hard? Implementing the Nation's Most...

85

BUILDING TECHNOLOGIES PROGRAM Iowa Compliance Implementation  

NLE Websites -- All DOE Office Websites (Extended Search)

Iowa Iowa Compliance Implementation and Evaluation (CIE) Guide COMPLIANCE IMPLEMENTATION AND EVALUATION (CIE) GUIDE 2 This Guide is designed to assist state and local code jurisdictions in achieving statewide compliance with the 2009 International Energy Conservation Code (IECC) for residential buildings and ANSI/ASHRAE/IESNA Standard 90.1-2007 for commercial buildings. COMPLIANCE IMPLEMENTATION AND EVALUATION (CIE) GUIDE 3 Iowa WHAT'S INSIDE CIE Guide Overview-Flow Diagram ........................................................................................................................... 5 PART 1: Guide Overview .................................................................................................................................................

86

Implementing for Implementing Executive Order 13423  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

IMPLEMENTING EXECUTIVE IMPLEMENTING EXECUTIVE ORDER 13423 "Strengthening Federal Environmental, Energy, and Transportation Management" March 29, 2007 0 Contents I. Introduction ......................................................................................................................1 A. Purpose..................................................................................................................1 B. Authority ...............................................................................................................1 C. Organization and Oversight ..................................................................................1 D. Overarching Policy and Directives .......................................................................4

87

ORISE: Implementing Improvements to Benefit the Scientific Peer...  

NLE Websites -- All DOE Office Websites (Extended Search)

Application The Oak Ridge Institute for Science and Education (ORISE) sets the standard for automated scientific peer reviews by continuously implementing process...

88

EOS standards  

SciTech Connect

An approach to creating accurate EOS for pressure standards is described. Applications to Cu, Au, and Ta are shown. Extension of the method to high compressions using DFT is illustrated. Comparisons with modern functionals show promise.

Greeff, Carl W [Los Alamos National Laboratory

2011-01-12T23:59:59.000Z

89

(Terminology standardization)  

SciTech Connect

Terminological requirements in information management was but one of the principal themes of the 2nd Congress on Terminology and Knowledge Engineering. The traveler represented the American Society for Testing and Materials' Committee on Terminology, of which he is the Chair. The traveler's invited workshop emphasized terminology standardization requirements in databases of material properties as well as practical terminology standardizing methods. The congress included six workshops in addition to approximately 82 lectures and papers from terminologists, artificial intelligence practitioners, and subject specialists from 18 countries. There were approximately 292 registrants from 33 countries who participated in the congress. The congress topics were broad. Examples were the increasing use of International Standards Organization (ISO) Standards in legislated systems such as the USSR Automated Data Bank of Standardized Terminology, the enhanced Physics Training Program based on terminology standardization in Physics in the Chinese province of Inner Mongolia, and the technical concept dictionary being developed at the Japan Electronic Dictionary Research Institute, which is considered to be the key to advanced artificial intelligence applications. The more usual roles of terminology work in the areas of machine translation. indexing protocols, knowledge theory, and data transfer in several subject specialties were also addressed, along with numerous special language terminology areas.

Strehlow, R.A.

1990-10-19T23:59:59.000Z

90

Mode-Stirred Method Implementation for HIRF Susceptibility Testing and Results Comparison with Anechoic Method  

Science Conference Proceedings (OSTI)

This paper describes the implementation of mode-stirred method for susceptibility testing according to the current DO-160D standard. Test results on an Engine Data Processor using the implemented procedure and the comparisons with the standard anechoic ...

Nguyen Truong X.; Ely Jay J.; Koppen Sandra V.

2001-07-01T23:59:59.000Z

91

Standards Coordination Office Homepage  

Science Conference Proceedings (OSTI)

Standards Coordination Office. ... About the Standards Coordination Office (SCO). The Standards Coordination Office of the ...

2013-07-31T23:59:59.000Z

92

Standard Modeling  

NLE Websites -- All DOE Office Websites (Extended Search)

Standard no es suficiente Standard no es suficiente Avanzar Volver Principal ESTOY PERDIDO!!! Si bien el Modelo Standard proporciona una descripción muy buena de los fenómenos observados en los experimentos, todavía es una teoría incompleta. El problema es que el Modelo Standard no puede explicar la causa por la que existen algunas partículas, del modo en que lo hacen. Por ejemplo, aún cuando los físicos conocían las masas de todos los quarks, a excepción de la del quark top desde hace muchos años, no podían simplemente predecir en forma exacta la masa del top, sin utilizar evidencia experimental, dado que el Modelo Standard carece de un modelo matemático para calcular el patrón que siguen los valores de las masas de las partículas. Otra cuestión está relacionada con el hecho que existen tres pares de

93

Synchrophasor Standards  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Development & Support Development & Support Kenneth Martin martin@electricpowergroup.com June 27-28, 2013 Washington, DC DOE/OE Transmission Reliability Program 2 Introduction  Synchrophasor measurement systems widely deployed  Enable a new generation of power system monitor & control capability - Improved power system analysis & system models - Wide area, high-resolution visibility - Basis for a new generation of controls  Research challenge - standards to enable interoperability - Measurement performance - Communications  Research focus - facilitate development, testing, and validation of standards to promote interoperability Basic phasor concept well known . A phasor is the complex form of the AC waveform √2 A cos (2 π ω 0 t + φ) A e

94

The Standards Forum, June 2001  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

By Rick Serbu, Manager, Technical Standards Program, U.S. Department of Energy By Rick Serbu, Manager, Technical Standards Program, U.S. Department of Energy T his article provides some discussion and information on incorpo- rating DOE Orders in contracts in general, and DOE O 252.1 (Technical Standards Program) in particular. This information may be of use in making a realistic assessment, from both a business and a contractual per- spective, of whether or not a DOE site "needs" an Order. Much of this information is covered in DOE G 252.1-1 (Technical Standards Program Guide). In essence, the Technical Standards Program (TSP) provides the means for DOE (and its contractors) to comply with Federal law and policy, and it establishes the infrastructure for DOE to conduct standards-related business and implement commitments made by DOE in re-

95

Safety Standards  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

US DOE Workshop US DOE Workshop September 19-20, 2012 International perspective on Fukushima accident Miroslav Lipár Head, Operational Safety Section M.Lipar@iaea.org +43 1 2600 22691 2 Content * The IAEA before Fukushima -Severe accidents management * The IAEA actions after Fukushima * The IAEA Action plan on nuclear safety * Measures to improve operational safety * Conclusions THE IAEA BEFORE FUKUSHIMA 4 IAEA Safety Standards IAEA Safety Standards F undamental S afety Principles Safety Fundamentals f o r p ro te c ti n g p e o p l e a n d t h e e n v i ro n m e n t IAEA Safety Standards Regulations for the Safe Transport of Radioactive Material 2005 E dit ion Safety Requirements No. T S-R-1 f o r p ro te c ti n g p e o p l e a n d t h e e n v i ro n m e n t IAEA Safety Standards Design of the Reactor Core for Nuclear Power Plants

96

STANDARD REFERENCE  

E-Print Network (OSTI)

The profession is strongly urged to use the standard reference on the financial framework in the EU, concerning endorsed IFRS in order to give a clear message to the market and to users of financial statements in and outside the EU.

unknown authors

2005-01-01T23:59:59.000Z

97

QSG - Categorize Implementation  

Science Conference Proceedings (OSTI)

... IMPLEMENT A DECOMMISSIONING STRATEGY When an information system is removed from operation, the information ...

2009-05-13T23:59:59.000Z

98

Climate, Community and Biodiversity Project Design Standards | Open Energy  

Open Energy Info (EERE)

Climate, Community and Biodiversity Project Design Standards Climate, Community and Biodiversity Project Design Standards Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Climate Community and Biodiversity Project Design Standards Agency/Company /Organization: The Climate Community and Biodiversity Alliance Sector: Land Topics: Implementation, Co-benefits assessment, Pathways analysis Resource Type: Guide/manual Website: www.climate-standards.org/standards/pdf/ccb_standards_second_edition_d Climate Community and Biodiversity Project Design Standards Screenshot References: Biodiversity Standards[1] "The CCB Standards have become the most widely used and respected international standard for the multiple-benefits of land-based carbon projects." References ↑ "Biodiversity Standards"

99

Stakeholder Engagement and Outreach: State Implementation Plans  

Wind Powering America (EERE)

State Implementation Plans State Implementation Plans State Implementation Plans are a policy vehicle that allow states and municipalities to receive emission reduction credit for wind power purchases. Under guidance issued by the U.S. Environmental Protection Agency in August 2004, States and municipalities can receive emission reduction credit in their State Implementation Plans for wind power purchases that reduce air emissions and help achieve attainment of the National Ambient Air Quality Standard for ozone. The National Renewable Energy Laboratory has developed model State Implementation Plan documentation to assist states in achieving this objective. For more information on State Implementation Plans, please see the following publications. Improving Regional Air Quality with Wind Power: Presentation

100

Energy Standard  

Gasoline and Diesel Fuel Update (EIA)

Hall Hall October 2011 Analysis of Impacts of a Clean www.eia.gov U.S. Department of Energy Washington, DC 20585 This report was prepared by the U.S. Energy Information Administration (EIA), the statistical and analytical agency within the U.S. Department of Energy. By law, EIA's data, analyses, and forecasts are independent of approval by any other officer or employee of the United States Government. The views in this report therefore should not be construed as representing those of the U.S. Department of Energy or other Federal agencies. U.S. Energy Information Administration | Analysis of Impacts of a Clean Energy Standard as requested by Chairman Hall i Contacts This report, Analysis of Impacts of a Clean Energy Standard as requested by Chairman Hall, was prepared under the

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Energy Standard  

Gasoline and Diesel Fuel Update (EIA)

Bingaman Bingaman November 2011 Analysis of Impacts of a Clean www.eia.gov U.S. Department of Energy Washington, DC 20585 This report was prepared by the U.S. Energy Information Administration (EIA), the statistical and analytical agency within the U.S. Department of Energy. By law, EIA's data, analyses, and forecasts are independent of approval by any other officer or employee of the United States Government. The views in this report therefore should not be construed as representing those of the U.S. Department of Energy or other Federal agencies. U.S. Energy Information Administration | Analysis of Impacts of a Clean Energy Standard as requested by Chairman Bingaman i Contacts This report, Analysis of Impacts of a Clean Energy Standard, as requested by Chairman Bingaman, was prepared

102

Standard Elements  

Science Conference Proceedings (OSTI)

Table 1   ASTM standards applicable to element-level testing of composites...Composite Plates Subjected to a Distributed Load Plate flexure D 6484 Open-Hole Compression Strength of Polymer Matrix Composites Open-hole compression strength Z 5370Z Compression After Impact Strength of Fiber-Resin Composites Compression after impact Z 7225Z Mixed Mode I-Mode II...

103

December 2007 Standards Forum and Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The Standards Forum & Standards Actions Page 1 December 2007 The Standards Forum & Standards Actions Page 1 December 2007 Continued on next page Technical Standards Program Manager's Note 1 Teaching Standards Development- Inspiring the Next Generation 2 The EPA Radiation Standard for Spent-Fuel Storage in a Geological Repository 3 Expanded Access to Hydrogen Codes and Standards 4 Really Following the Building Code 6 Technical Standards Manager Spotlight 7

104

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Commercial Fed. Government Industrial Local Government Nonprofit Residential Schools State Government Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Wind Energy Sources Solar Program Info State Minnesota Program Type Interconnection Provider Minnesota Public Utilities Commission Minnesota's net-metering law, enacted in 1983, applies to all investor-owned utilities, municipal utilities and rural electric cooperatives. Qualifying facilities of less than 1,000 kilowatts (kW) are eligible for net metering. However, uniform interconnection regulations were not implemented when net metering was established.

105

Implementation, Certification and Enforcement | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementation, Certification Implementation, Certification and Enforcement Implementation, Certification and Enforcement The U.S. Department of Energy (DOE) is authorized by the Energy Policy and Conservation Act of 1975 (as amended) to enforce compliance with the energy and water conservation standards established for certain consumer products and commercial and industrial equipment. To ensure the implementation of the current standards for covered appliances and equipment, DOE has published certification, compliance, and enforcement regulations for these products and equipment in the Code of Federal Regulations (CFR) at 10 CFR part 429. Please note that the previous link is to the Electronic Code of Federal Regulations (e-CFR), which is a version of the CFR updated daily. It is not an official legal edition of

106

May 2007 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technical Technical Standards in Revision 1 DOE Technical Standards Posted in RevCom for TSP 1 DOE Technical Standards in Reaffirmation 1 DOE Technical Standards Change Notices 1 DOE Technical Standards Published 1 Non-Government Standards Actions 2

107

Seminar on building codes and standards  

SciTech Connect

A seminar was conducted for state building code officials and state energy officials to discuss the following: status of the states regulatory activities for energy conservation standards for buildings; the development, administration, and enforcement processes for energy conservation standards affecting new construction; lighting and thermal standards for existing buildings; status of the development and implementation of the Title III Program, Building Energy Performance Standards (BEPS); and current status of the State Energy Conservation Program. The welcoming address was given by John Wenning and the keynote address was delivered by John Millhone. Four papers presented were: Building Energy Performance Standards Development, James Binkley; Lighting Standards in Existing Buildings, Dorothy Cronheim; Implementation of BEPS, Archie Twitchell; Sanctions for Building Energy Performance Standards, Sue Sicherman.

Not Available

1980-01-01T23:59:59.000Z

108

Implementation of International Electrotechnical Commission (IEC) 61850  

Science Conference Proceedings (OSTI)

The IEC 61850 standard for next-generation substation automation allows the integration of systems built from multivendor intelligent electronic devices (IEDs) to perform protection, monitoring, automation, metering, and control functions. This report outlines what utilities need to know about implementing the standardits benefits and costs, issues, lessons learned, and strategies for successful migration. Implementation will require utilities to migrate from traditional grid components and legacy commun...

2010-12-17T23:59:59.000Z

109

A Middle School Standards-based Science Curriculum Handbook.  

E-Print Network (OSTI)

??As teachers implement the National Science Education Standards (1996) many must change the instructional methods they have used throughout their careers. This handbook will assist (more)

Hess, Eleanor B.

2005-01-01T23:59:59.000Z

110

Catalog of Standards  

Science Conference Proceedings (OSTI)

... Catalog of Standards. ... As of May 2013, the number of standards or standards components added to the Catalog of Standards stands at 56. ...

2013-07-31T23:59:59.000Z

111

IEEE 1588 Products & Implementations  

Science Conference Proceedings (OSTI)

... Facsimile. 100 Bureau Drive, M/S 8220 Gaithersburg, MD 20899-8220. IEEE 1588 Products & Implementations. This page ...

2012-11-06T23:59:59.000Z

112

DOE standard: Radiological control  

Science Conference Proceedings (OSTI)

The Department of Energy (DOE) has developed this Standard to assist line managers in meeting their responsibilities for implementing occupational radiological control programs. DOE has established regulatory requirements for occupational radiation protection in Title 10 of the Code of Federal Regulations, Part 835 (10 CFR 835), ``Occupational Radiation Protection``. Failure to comply with these requirements may lead to appropriate enforcement actions as authorized under the Price Anderson Act Amendments (PAAA). While this Standard does not establish requirements, it does restate, paraphrase, or cite many (but not all) of the requirements of 10 CFR 835 and related documents (e.g., occupational safety and health, hazardous materials transportation, and environmental protection standards). Because of the wide range of activities undertaken by DOE and the varying requirements affecting these activities, DOE does not believe that it would be practical or useful to identify and reproduce the entire range of health and safety requirements in this Standard and therefore has not done so. In all cases, DOE cautions the user to review any underlying regulatory and contractual requirements and the primary guidance documents in their original context to ensure that the site program is adequate to ensure continuing compliance with the applicable requirements. To assist its operating entities in achieving and maintaining compliance with the requirements of 10 CFR 835, DOE has established its primary regulatory guidance in the DOE G 441.1 series of Guides. This Standard supplements the DOE G 441.1 series of Guides and serves as a secondary source of guidance for achieving compliance with 10 CFR 835.

Not Available

1999-07-01T23:59:59.000Z

113

Environmental Protection Implementation Plan  

SciTech Connect

This Environmental Protection Implementation Plan is intended to ensure that the environmental program objectives of Department of Energy Order 5400.1 are achieved at SNL/California. The Environmental Protection Implementation Plan serves as an aid to management and staff to implement new environmental programs in a timely manner.

Brekke, D.D.

1994-01-01T23:59:59.000Z

114

Reading Lists in Cambridge: A Standard System?  

E-Print Network (OSTI)

of lists. Some of the main benefits of the adoption of a standard system would be: Consistent user experience Ease of access to resources Ease of list discovery Streamlining of workflows (functionality, list maintenance, stock management... with pedagogic support. Implementation The key organisations for implementation are: University Library (UL) CARET Management Information Services Division (MISD) A successful implementation will rely on engaging key users, particularly academics...

Jones, Huw

115

Establishment, Implementation and Enforcement of Building Codes and Standards  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

筑规范和标准的建立,执行和监管 筑规范和标准的建立,执行和监管 Nanette Lockwood 政府事务全球总监 Solutia公司 第二届中美能效论坛 2011年5月5-6日|劳伦斯伯克利国家实验室,伯克利市,加州 2 Crystex ® Solutia 公司简介 先进建筑材料 高性能薄膜材料 技术专长 2010年利润 $19 亿美元 办公场所 50个以上 雇员 3,300人 第二届中美能效论坛 2011年5月5-6日|劳伦斯伯克利国家实验室,伯克利市,加州 美国建筑规范和标准 * 定期开发、更新,并且在国家 层面上发布面向当地应用的建 筑规范和标准。 * 能够被国家、州(省)和地方

116

ANSI/NIST-ITL Standard Profiles and Implementations  

Science Conference Proceedings (OSTI)

... Member states are Alaska, Idaho, Montana, Nevada, Oregon, Utah, Washington and Wyoming, with California as an Interface member. ...

2012-08-13T23:59:59.000Z

117

Implementation of Pure Fluid and Natural Gas Standards ...  

Science Conference Proceedings (OSTI)

... EW, Diky, V. , Smith, BL, and Bruno, TJ, Chemically Authentic Surrogate Mixture Model for the Thermophysical Properties of a Coal-Derived-Liquid ...

2013-04-11T23:59:59.000Z

118

Implementation of the Renewable Fuel Standard (RFS) in the ...  

U.S. Energy Information Administration (EIA)

Biomass-based diesel In the LFMM linear program, RFS requirements are modeled as system-wide constraints, with the possibility of waiver purchases

119

2010 Report to Congresss -- Implementation Report: Energy Conservation Standard Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

10 10 U.S. Department of Energy 2 Table of Contents List of Acronyms ...................................................................................................................................... 3 Introduction .............................................................................................................................................. 4 Backlog and EPACT 2005 ....................................................................................................................... 5 State of New York, et al. v. Bodman; and NRDC, Inc. et al. v. Bodman ...............................................5 Energy Independence and Security Act of 2007 .................................................................................. 6

120

1998 federal technical standards workshop: Proceedings  

Science Conference Proceedings (OSTI)

The theme for the 1998 workshop was Standards Management -- A World of Change and Opportunities. The workshop`s goal was to further the implementation of the National Technology Transfer and Advancement Act of 1995 (Public Law 104-113) through the sharing of standards management success stories, lessons learned, and emerging initiatives within the Executive Branch of the Federal Government. The target audience for this workshop included agency/department and contractor personnel and representatives of standards developing organizations that either used technical standards in their work for the Federal Government of participated in standards writing/management activities in support of the missions and programs of Federal agencies/departments. As with previous standards workshops sponsored by the DOE, views on the technical subject areas under the workshop theme were solicited from and provided by agency Standards Executives and standards program managers, voluntary standards organizations, and the private sector. This report includes vugraphs of the presentations.

NONE

1998-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Federal Information Processing Standards  

Science Conference Proceedings (OSTI)

... Federal Information Processing Standards Publications (FIPS PUBS). ... Replacement Standards for Withdrawn FIPS on Geographic Codes.

2013-07-30T23:59:59.000Z

122

March 2007 Standards Forum and Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

March 2007 March 2007 Continued on next page TSP Manager's Notes 1 Domestic Programs (American National Standards) Overview 2 Aerospace Industry Advocates Standards Selection Based on Technical Merit, Not Semantics 3 Report Recommends Withdrawal of OMB Risk Assessment Bulletin 4 Technical Standards Manager Spotlight 5 Topical Committee Developments 6 Welcome Aboard the TSMC! 7 Standards Actions 8 DOE Standards Actions 8

123

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Residential Refrigerators and Freezers Residential Refrigerators and Freezers Sign up for e-mail updates on regulations for this and other products Manufacturers have been required to comply with the Department of Energy's (DOE) energy conservation standards for residential refrigerators and freezers since 1990. Residential refrigerators and freezers include refrigerators, refrigerator-freezers, and freezers, such as standard-size residential units as well as compact units used in offices and dormitory rooms. Known collectively as "refrigeration products," these appliances chill and preserve food and beverages, provide ice and chilled water, and freeze food. The standard implemented in 1990 will save approximately 5.6 quads of energy and result in approximately $61.7 billion in energy bill savings for products shipped from 1990-2019. The standard will avoid about 312.4 million metric tons of carbon dioxide emissions, equivalent to the annual greenhouse gas emissions of about 61.3 million automobiles.

124

Appliances and Commercial Equipment Standards: Guidance  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office Office HOME ABOUT ENERGY EFFICIENT TECHNOLOGIES RESIDENTIAL BUILDINGS COMMERCIAL BUILDINGS APPLIANCE & EQUIPMENT STANDARDS BUILDING ENERGY CODES EERE » Building Technologies Office » Appliances & Equipment Standards About Standards & Test Procedures Implementation, Certification & Enforcement Rulemakings & Notices Further Guidance ENERGY STAR® Guidance and Frequently Asked Questions This webpage is designed to provide guidance and answer Frequently Asked Questions (FAQs) on the U.S. Department of Energy's appliance standards program. Guidance types span all covered products and covered equipment and cover such topics as: definitions, scope of coverage, conservation standards, test procedures, certification, Compliance and Certification Management System (CCMS), and enforcement. This website offers users an

125

National Agenda for Hydrogen Codes and Standards  

SciTech Connect

This paper provides an overview of hydrogen codes and standards with an emphasis on the national effort supported and managed by the U.S. Department of Energy (DOE). With the help and cooperation of standards and model code development organizations, industry, and other interested parties, DOE has established a coordinated national agenda for hydrogen and fuel cell codes and standards. With the adoption of the Research, Development, and Demonstration Roadmap and with its implementation through the Codes and Standards Technical Team, DOE helps strengthen the scientific basis for requirements incorporated in codes and standards that, in turn, will facilitate international market receptivity for hydrogen and fuel cell technologies.

Blake, C.

2010-05-01T23:59:59.000Z

126

ISA Approves Standard for Wireless Automation in Process Control  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ISA Approves Standard for Wireless Automation in Process Control ISA Approves Standard for Wireless Automation in Process Control Applications ISA Approves Standard for Wireless Automation in Process Control Applications On September 9, the Standards and Practices Board of the International Society for Automation (ISA) approved the ISA-100.11a wireless standard, "Wireless Systems for Industrial Automation: Process Control and Related Applications," making it an official ISA standard. ISA Approves Standard for Wireless Automation in Process Control Applications More Documents & Publications DOE/OE National SCADA Test Bed Fiscal Year 2009 Work Plan Wireless System Considerations When Implementing NERC Critical Infrastructure Protection Standards Control Systems Security Standards: Accomplishments And Impacts

127

Building Technologies Office: Standardized Templates for Reporting Test  

NLE Websites -- All DOE Office Websites (Extended Search)

Standardized Templates Standardized Templates for Reporting Test Results to someone by E-mail Share Building Technologies Office: Standardized Templates for Reporting Test Results on Facebook Tweet about Building Technologies Office: Standardized Templates for Reporting Test Results on Twitter Bookmark Building Technologies Office: Standardized Templates for Reporting Test Results on Google Bookmark Building Technologies Office: Standardized Templates for Reporting Test Results on Delicious Rank Building Technologies Office: Standardized Templates for Reporting Test Results on Digg Find More places to share Building Technologies Office: Standardized Templates for Reporting Test Results on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement

128

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Residential Dishwashers Residential Dishwashers Sign up for e-mail updates on regulations for this and other products Manufacturers have been required to comply with the Department of Energy's (DOE) energy conservation standards for residential dishwashers since 1988. Residential dishwashers use water and detergent to wash and rinse dishware, glassware, eating utensils, and most cooking utensils. Some dishwashers also dry dishes. Standards implemented in 1994 will save approximately 1.6 quads of energy and result in approximately $19.8 billion in energy bill savings for products shipped from 1994-2023. The standard will avoid about 50.3 million metric tons of carbon dioxide emissions, equivalent to the annual greenhouse gas emissions of about 9.7 million automobiles. Standards implemented in 2010 will save approximately 0.6 quads of energy and result in approximately $10.3 billion in energy bill savings for products shipped from 2010-2034. The standard will avoid about 32.5 million metric tons of carbon dioxide emissions, equivalent to the annual greenhouse gas emissions of about 6.4 million automobiles.

129

Design and Implementation  

Science Conference Proceedings (OSTI)

... The application for database administration and the web interface for generating reports are implemented using the Tcl/Tk[OUST] scripting ...

130

May 2006 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards Actions 1 Standards Actions 1 New Projects and Technical Standards in Revision 1 DOE Technical Standards Posted in RevCom for TSP 1 DOE Technical Standards in Reaffirmation 1 DOE Technical Standards Change Notices 1 DOE Technical Standards Published 1 Non-Government Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2

131

Environmental Restoration Quality Program Implementation Plan  

SciTech Connect

The Environmental Restoration (ER) Program requirements for implementation of DOE Order 5700.6C are identified in the Environmental Restoration Quality Program Plan, (QPP). Management systems necessary to implement the ER QPP consist of the necessary standards and procedures required to be developed to adequately control ER processes. To the extent possible, Martin Marietta Energy Systems, Inc., standards and procedures will be utilized at the ER Program level, and requirements will not be repeated. The quality management systems identified for enhancement or development are identified in the section on Procedure Development Strategy and directly relate to unique ER Program activities. Procedures and standards that currently exist in the ER Program will be validated for compliance with ER QPP requirements.

1992-08-01T23:59:59.000Z

132

Appliance Energy Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Stove, washer, dryer, refrigerator, Energy Star Label Appliance Energy Standards Energy Efficiency Standard The Energy Efficiency Standards Group analyzes technical, economic, and...

133

ISO Standards Documents  

Science Conference Proceedings (OSTI)

ISO/TC 34: Food products and TC 34/SC 17: Management systems for food safety ISO Standards Documents iso3rss ISO Standards Development ISO Standards Development

134

September 2006 Standards Forum/Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

September 2006 September 2006 TSP Manager's Notes 1 TEN YEARS AFTER THE NTTAA: 1996-2006 2 Committee on Nuclear Fuel Cycle Approves Two New Standards 4 Renewable Portfolio Standards Help Wind Industry to Sail 5 Technical Standards Manager Spotlight 5 World Standards Day 2006 in

135

Department of Energy Requests Fast Track Rulemaking for Implementing...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementing Energy Efficiency Standards February 26, 2007 - 10:28am Addthis WASHINGTON, DC - U.S. Department of Energy (DOE) Secretary Samuel W. Bodman today sent legislation to...

136

Building Technologies Program: History of Federal Appliance Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

History of Federal History of Federal Appliance Standards to someone by E-mail Share Building Technologies Program: History of Federal Appliance Standards on Facebook Tweet about Building Technologies Program: History of Federal Appliance Standards on Twitter Bookmark Building Technologies Program: History of Federal Appliance Standards on Google Bookmark Building Technologies Program: History of Federal Appliance Standards on Delicious Rank Building Technologies Program: History of Federal Appliance Standards on Digg Find More places to share Building Technologies Program: History of Federal Appliance Standards on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement Rulemakings & Notices Further Guidance ENERGY STAR® Popular Links

137

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Small, Large, and Very Large Commercial Package Air Conditioners and Heat Pumps Small, Large, and Very Large Commercial Package Air Conditioners and Heat Pumps Sign up for e-mail updates on regulations for this and other products The Department of Energy (DOE) regulates the energy efficiency of small, large, and very large commercial package air conditioners and heat pumps. Commercial air conditioners and heat pumps are air-cooled, water-cooled, evaporatively-cooled, or water source unitary air conditioners or heat pumps that are used for space conditioning of commercial and industrial buildings. The standards implemented in 2010 for small and large, air-cooled commercial package air conditioners and heat pumps, and SPVUs, will save approximately 1.7 quads of energy and result in approximately $28.9 billion in energy bill savings for products shipped from 2010-2034. These standards will avoid about 90.3 million metric tons of carbon dioxide emissions, equivalent to the annual greenhouse gas emissions of 31.1 million automobiles. The standard implemented in 2010 for very large, air-cooled commercial package air conditioners and heat pumps will save approximately 0.43 quads of energy and result in approximately $4.3 billion in energy bill savings for products shipped from 2010-2034. The standard will avoid about 22.6 million metric tons of carbon dioxide emissions, equivalent to the annual greenhouse gas emissions of 4.4 million automobiles.

138

April 2006 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 New Projects and Technical Standards in Revision 1 DOE Technical Standards Posted in RevCom for TSP 1 DOE Technical Standards in Reaffirmation 1 DOE Technical Standards Change Notices 1 DOE Technical Standards Published 1 Non-Government Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 DOE Technical Standards Program Document Status

139

Standard-Related Links  

Science Conference Proceedings (OSTI)

... Standard-Related Links. ... Association for Clinical Chemistry ACS - American Chemical Society ANSI - American National Standards Institute AOAC ...

2013-06-28T23:59:59.000Z

140

Standard Reference Materials  

Science Conference Proceedings (OSTI)

... Inn, KGW, Liggett, WS, and Hutchinson, JMR (1984), "The National Bureau of Standards Rocky Flats Soil Standard Reference Material," Nuclear ...

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Federal Technical Standards Workshop  

Science Conference Proceedings (OSTI)

... missions, authorities, priorities, and budget resources.". ... of developing a strategic standards management plan. ... Director of NIST's Office of Standards ...

2010-10-05T23:59:59.000Z

142

Process Control System Cyber Security Standards - An Overview  

Science Conference Proceedings (OSTI)

The use of cyber security standards can greatly assist in the protection of process control systems by providing guidelines and requirements for the implementation of computer-controlled systems. These standards are most effective when the engineers and operators, using the standards, understand what each standard addresses. This paper provides an overview of several standards that deal with the cyber security of process measurements and control systems.

Robert P. Evans

2006-05-01T23:59:59.000Z

143

Implementation Proposal for  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementation Proposal for Implementation Proposal for The National Action Plan on Demand Response Report to Congress Prepared by staff of the Federal Energy Regulatory Commission and the U.S. Department of Energy The opinions and views expressed in this staff report do not necessarily represent those of the Federal Energy Regulatory Commission, its Chairman, or individual Commissioners, and are not binding on the Commission. Implementation Proposal for The National Action Plan on Demand Response July 2011 TABLE OF CONTENTS Executive Summary ............................................................................................... iii I. Introduction ......................................................................................................1

144

Status of European appliance standards  

SciTech Connect

The European Community (EC) recently commissioned a study of the impact of potential appliance standards on electricity consumption in the twelve EC nations. This study looks at refrigerators, freezers, dishwashers, clothes washers, and clothes dryers. The impact of minimum efficiency standards on electricity use over the time period from 1995--2010 is estimated. The results of this study were presented to the EC in September of 1991. Revisions were made to the draft report and final copies sent to all interested parties. The member nations of the EC will soon consider whether they wish to implement uniform energy efficiency standards that would take effect in 1995. The results of the study described above will be presented and the political considerations will be discussed. In addition, data describing the appliance market in Europe will be presented.

Turiel, I. (Lawrence Berkeley Lab., CA (United States)); Lebot, B. (Agence de L'Environnement et de la Maitrise de L'Energie, Valbonne (France))

1992-05-01T23:59:59.000Z

145

Thread-safety in an MPI implementation: Requirements and analysis  

Science Conference Proceedings (OSTI)

The MPI-2 Standard has carefully specified the interaction between MPI and user-created threads. The goal of this specification is to allow users to write multithreaded MPI programs while also allowing MPI implementations to deliver high performance. ... Keywords: MPI implementation, Message-passing interface (MPI), Multithreaded programming, Thread-safety

William Gropp; Rajeev Thakur

2007-09-01T23:59:59.000Z

146

Unveiling the Implementation Guide  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oak Ridge National Laboratory www.ornl.gov Oak Ridge National Laboratory www.ornl.gov Unveiling the Implementation Guide October 11, 2011 Michaela Martin Program Manager Residential, Commercial, and Industrial Energy Efficiency Oak Ridge National Laboratory 2 | Oak Ridge National Laboratory www.ornl.gov Guiding Principles for Successfully Implementing Industrial Energy Assessment Recommendations * New resource for industry * Identifies key principles and actions that lead to successful implementation of energy assessment recommendations * Connects readers with a variety of trusted resources * Simple tools for supporting energy management programs and continuous energy performance improvement efforts * Available in hard copy and on the web Implementation Guide Overview 3 | Oak Ridge National Laboratory www.ornl.gov

147

INSTRUCTIONS FOR IMPLEMENTING EXECUTIVE  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

March 29, 2007 INSTRUCTIONS FOR IMPLEMENTING EXECUTIVE ORDER 13423 "Strengthening Federal Environmental, Energy, and Transportation Management" i Contents I. Introduction ......................................................................................................................1 A. Purpose..................................................................................................................1 B. Authority ...............................................................................................................1 C. Organization and Oversight ..................................................................................1 D. Overarching Policy and Directives .......................................................................4

148

Environmental protection Implementation Plan  

SciTech Connect

This ``Environmental Protection Implementation Plan'' is intended to ensure that the environmental program objectives of Department of Energy Order 5400.1 are achieved at SNL/California. This document states SNL/California's commitment to conduct its operations in an environmentally safe and responsible manner. The ``Environmental Protection Implementation Plan'' helps management and staff comply with applicable environmental responsibilities.

R. C. Holland

1999-12-01T23:59:59.000Z

149

October 2005 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards Actions 1 Standards Actions 1 New Projects and DOE Technical Standards in Revision 1 DOE Technical Standards Posted in RevCom for TSP 1 DOE Technical Standards in Reaffirmation 1 DOE Technical Standards Change Notices 1 DOE Technical Standards Recently Published 1 Non-Government Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 DOE Technical Standards Program

150

DOE Directives, Regulations, and Standards Portal - Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Globe Image Department of Energy (DOE) Technical Standards Program Home Search Approved Standards Recently Approved RevCom Logo RevCom for TSP Drafts for Review Registered Projects...

151

April 2007 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

New Projects and Technical Standards in Revision 1 DOE Technical Standards Posted in RevCom for TSP 1 DOE Technical Standards in Reaffirmation 1 DOE Technical Standards Change Notices 1 Technical Standards Published 2 Non-Government Standards Actions 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 DOE Technical

152

November 2005 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE Technical DOE Technical Standards in Revision 1 DOE Technical Standards Posted in RevCom for TSP 1 DOE Technical Standards in Reaffirmation 1 DOE Technical Standards Change Notices 1 DOE Technical Standards Revisions 1 Non-Government Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association

153

NIST Global Standards Information Global Standards News  

Science Conference Proceedings (OSTI)

... 2010 The National Institute of Standards and Technology (NIST) has advised the Federal Energy Regulatory Commission ... DGI), Austin, Texas, were ...

154

NIST Global Standards Information Standards Education  

Science Conference Proceedings (OSTI)

... Grants supporting the development of new learning resources and course modules integrating standards into the formal curriculum in Business and ...

155

September 2005 Standards Forum and Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Page September 2005 Page September 2005 TSP Manager's Notes 1 The Halo Effect: American National Standards and the rest 2 Standards Development for Report- ing of Declarable Substances 5 Technical Standards Manager Spotlight 8 DOE Revises "Integration of Environment, Safety, and Health

156

December 2006 Standards Forum and Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

December 2006 December 2006 TSP Manager's Notes 1 Meeting In The Middle 2 Plain Talk for a New Generation 3 Licensing New Nuclear Power Plants 4 ANSI Government Affairs Overview 5 Technical Standards Manager Spotlight 7 Topical Committee Developments 8 Welcome Aboard the TSMC! 8 Standards Actions 9 DOE Standards Actions 9

157

Alternative implementation of the Higgs boson  

E-Print Network (OSTI)

We discuss an alternative implementation of the Higgs boson within the Standard Model which is possible if the renormalizability condition is relaxed. Namely, at energy scale $\\Lambda$ the Higgs boson interacts at tree-level only with matter fermions, while the full gauge invariance is still maintained. The interactions with the electroweak gauge bosons are induced at low energies through the radiative corrections. In this scenario the Higgs boson can be arbitrarily heavy, interacting with the Standard Model fields arbitrarily weakly. No violation of unitarity in the scattering of longitudinal electroweak bosons occurs, since they become unphysical degrees of freedom at energies $\\Lambda \\sim \\mathrm{TeV}$.

Robert Foot; Archil Kobakhidze

2009-04-22T23:59:59.000Z

158

Standards Actions, July 2002  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards Program Document Status 07-01-2002 Activity Summary In Conversion - 4 In Preparation - 46 Out for Comment - 14 Published this Month - 2 5-year Review Status Revision in Progress - 11 Reaffirmation in Progress - 12 Cancellation Pending - 7 Cancellation in Progress - 1 No Current Action - 19 Inside this issue: DOE Technical Standards Projects Initiated 1 DOE Technical Standards Re- cently Sent for Coordination 1 DOE Technical Standards Re- cently Published 1 American National Standards Institute 2 American Society for Testing and Materials International 4 Visit the Technical Standards Program Web Site at http://tis.eh.doe.gov/techstds/. Standards Actions- July 2002 Standards Actions DOE Technical Standards Projects Initiated

159

Standards Actions, May 2001  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

30-2001 30-2001 Activity Summary In Conversion - 4 In Preparation - 39 Out for Comment - 19 Published this Month - 0 5-year Review Status Revision in Progress - 4 Reaffirmation in Progress - 23 Cancellation Pending - 9 Cancellation in Progress - 18 No Current Action - 12 Inside this issue: DOE Technical Standards Projects Initiated 1 DOE Technical Standards Proposed for Reaffirmation 1 Proposed Cancellation of DOE Technical Standards 2 Published DOE Technical Standards 3 American National Standards Institute 3 American National Standards 6 American Society for Testing and Materials 6 Visit the Technical Standards Program Web Site at http://tis.eh.doe.gov/techstds/. May 2001 Standards Actions DOE Technical Standards Projects Initiated

160

DOE Technical Standards Program Standards Actions Newsletter  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

* * New DOE Standard, Communicating Waste Characterization and DOT Hazard Classification Requirements * Workshops and Events * The Annual Energy Facility Contractors Group Safety Analysis Workshop * 2012 Chemical Safety and Life Cycle Management Workshop * Nuclear Safety- Related Standards Activity INSIDE THIS ISSUE April 2012 Standards Actions Technical Standards Program Newsletter www.hss.energy.gov/nuclearsafety/ns/techstds/ New DOE Standard, Communicating Waste Characterization and DOT Hazard Classification Requirements The Department of Energy (DOE) Office of Environmental Management (EM) has a challenging mission to solve many problems posed by the legacy of the Cold War, including the transportation of unprecedented amounts of contaminated waste,

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

May 2005 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Notices 1 DOE Technical Standards Revisions 1 DOE Technical Standards Projects Initiated 1 Non-Government Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 DOE Technical Standards Program Document Status 04-27-2005 Activity Summary In Conversion - 4 In Preparation - 25

162

AEDG Implementation Recommendations: Ventilation | Building Energy Codes  

NLE Websites -- All DOE Office Websites (Extended Search)

Ventilation Ventilation The Advanced Energy Design Guide (AEDG) for Small Office Buildings, 30% series, seeks to achieve 30% savings over ASHRAE Standard 90.1-1999. This guide focuses on improvements to small office buildings, less than 20,000ft2. The recommendations in this article are adapted from the implementation section of the guide and focus on ventilation air; exhaust air; control strategies; carbon dioxide sensors; economizers. Publication Date: Wednesday, May 13, 2009 air_ventilation.pdf Document Details Affiliation: DOE BECP Focus: Compliance Building Type: Commercial Code Referenced: ASHRAE Standard 90.1-1999 Document type: AEDG Implementation Recommendations Target Audience: Architect/Designer Builder Contractor Engineer State: All States Contacts Web Site Policies

163

AEDG Implementation Recommendations: Testing and Balancing | Building  

NLE Websites -- All DOE Office Websites (Extended Search)

Testing and Balancing Testing and Balancing The Advanced Energy Design Guide (AEDG) for Small Office Buildings, 30% series, seeks to achieve 30% savings over ASHRAE Standard 90.1-1999. This guide focuses on improvements to small office buildings, less than 20,000ft2. The recommendations in this article are adapted from the implementation section of the guide and focus on testing, adjusting, and balancing; heating sources; filters. Publication Date: Sunday, April 13, 2008 air_testing_and_balancing.pdf Document Details Affiliation: DOE BECP Focus: Compliance Building Type: Commercial Code Referenced: ASHRAE Standard 90.1-1999 Document type: AEDG Implementation Recommendations Target Audience: Architect/Designer Builder Contractor Engineer State: All States Contacts Web Site Policies U.S. Department of Energy

164

AEDG Implementation Recommendations: Daylighting Controls | Building Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Controls Controls The Advanced Energy Design Guide (AEDG) for Small Office Buildings, 30% series, seeks to achieve 30% savings over ASHRAE Standard 90.1-1999. This guide focuses on improvements to small office buildings, less than 20,000ft2. The recommendations in this article are adapted from the implementation section of the guide and focus on expanded recommendations for daylighting controls; photo sensor placement; calibration and commissioning; daylight levels. Publication Date: Wednesday, May 13, 2009 air_daylighting_controls.pdf Document Details Affiliation: DOE BECP Focus: Compliance Building Type: Commercial Code Referenced: ASHRAE Standard 90.1-1999 Document type: AEDG Implementation Recommendations Target Audience: Architect/Designer Builder Contractor Engineer

165

DOE Approved Technical Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE Technical Standards Program » DOE DOE Technical Standards Program » DOE Approved Technical Standards DOE Approved Technical Standards Document ID Filter Document ID sort ascending Title Date DOE-STD-7501-99 The DOE Corporate Lessons Learned Programs Superseding DOE-STD-7501-95 Including Change Notice No. 1 (September 1997) This technical standard provides management expectations and a framework for the DOE Corporate Lessons Learned Program. The framework is intended to support development and implementation of a DOE-wide lessons learned infrastructure 01/20/2000 DOE-STD-6005-01 Industrial Hygiene Practices This standard recommends industrial hygiene practices to support components of the Worker Protection Program required by Department of Energy (DOE) Order 440.1A, “Worker Protection Management for DOE Federal and Contractor Employees. 04/30/2001

166

Implementing the National Broadband  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Type text] Type text] Response to Request for Information from the Department of Energy: Implementing the National Broadband Plan by Empowering Consumers and the Smart Grid: Data Access, Third Party Use, and Privacy [FR Doc. 2010-11127] July 12, 2010 EnerNOC Page 2 of 8 EnerNOC, Inc. ("EnerNOC") is pleased to provide these comments to the Department of Energy in response to the Request for Information "Implementing the National Broadband Plan by Empowering Consumers and the Smart Grid: Data Access, Third Party Use, and Privacy." EnerNOC is a provider of demand response and energy efficiency solutions to utilities, Independent

167

Permanent Markers Implementation Plan  

NLE Websites -- All DOE Office Websites (Extended Search)

WIPP 04-3302 WIPP 04-3302 Permanent Markers Implementation Plan August 19, 2004 United States Department of Energy Waste Isolation Pilot Plant Carlsbad Field Office Carlsbad, New Mexico DOE/WIPP 04-3302 ii Permanent Markers Implementation Plan Waste Isolation Pilot Plant Carlsbad, New Mexico August 19, 2004 Prepared for: Washington Regulatory and Environmental Services an affiliate of Washington TRU Solutions, LLC P.O. Box 2078 Carlsbad, New Mexico 88221 Prepared by: John Hart and Associates, P.A. 2815 Candelaria Road, N.W. Albuquerque, New Mexico 87107 (505) 344-7868 DOE/WIPP 04-3302 iii Table of Contents Table of Contents.................................................................................................

168

Environmental Protection Implementation Plan  

SciTech Connect

This Environmental Protection Implementation Plan is intended to ensure that the environmental program objectives of Department of Energy Order 5400.1 are achieved at SNL/California. This document states SNL/California`s commitment to conduct its operations in an environmentally safe and responsible manner. The Environmental Protection Implementation Plan helps management and staff comply with applicable environmental responsibilities. This report focuses on the following: notification of environmental occurrences; general planning and reporting; special programs and plans; environmental monitoring program; and quality assurance and data verification.

Brekke, D.D.

1995-11-01T23:59:59.000Z

169

PICs Implementation Plan  

NLE Websites -- All DOE Office Websites (Extended Search)

WIPP 04-2301 WIPP 04-2301 Passive Institutional Controls Implementation Plan August 19, 2004 United States Department of Energy Waste Isolation Pilot Plant Carlsbad Field Office Carlsbad, New Mexico DOE/WIPP 04-2301 Passive Institutional Controls Implementation Plan Waste Isolation Pilot Plant Carlsbad, New Mexico August 19, 2004 Prepared for: Washington Regulatory and Environmental Services an affiliate of Washington TRU Solutions, LLC P.O. Box 2078 Carlsbad, New Mexico 88221 Prepared by: John Hart and Associates, P.A. 2815 Candelaria Road, N.W. Albuquerque, New Mexico 87107 (505) 344-7868 DOE/WIPP 04-2301 i Table of Contents List of Tables .....................................................................................................................ii

170

IEC 61850 Implementation  

Science Conference Proceedings (OSTI)

The International Electrotechnical Commission (IEC) standard 61850, Substation Automation, is designed to enable more advanced levels of automation in electric power systems. Realizing the potential of the smart grid will not be possible without these standards because legacy systems cannot support the advanced functions required to manage increased automation and system complexity. IEC 61850 offers numerous benefits, as well as challenges.Due to the breadth of IEC 61850, ...

2012-11-16T23:59:59.000Z

171

NETL: Publication Standards Manual  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards Manual Publications Publication Standards Manual Click on the logo to access the NETL Publication Standards Manual 2003 APEX Logo Click on the logo or on the link below...

172

Thick Buildings [Standards  

E-Print Network (OSTI)

STANDARDS The idea of tracts of windowless indoor space hassider U.S. practices and standards? building with four sidesAs these codes and standards change future generations may

Coffin, Christie Johnson

1995-01-01T23:59:59.000Z

173

Questioning Copyright in Standards  

E-Print Network (OSTI)

adoption and use of privately drafted industry standards).arising from abuses of standard-setting processes are well-at 7. Compliance with standards has often implicated patent

Samuelson, Pam

2006-01-01T23:59:59.000Z

174

February 2007 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE Technical Standards Posted in RevCom for TSP 1 DOE Technical Standards in Reaffirmation 1 DOE Technical Standards Change Notices 1 DOE Technical Standards Published1 Non-Government Standards Actions 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 Publication Staff Roster 2

175

New initiative on runtime compatibility for MPI implementations | Argonne  

NLE Websites -- All DOE Office Websites (Extended Search)

initiative on runtime compatibility for MPI implementations initiative on runtime compatibility for MPI implementations December 3, 2013 Tweet EmailPrint Researchers at Argonne National Laboratory have established an initiative to tackle the problem of maintaining runtime compatibility between message passing interface (MPI) implementations on high-performance computer architectures. The project, called the MPICH ABI Compatibility Initiative, involves the producers of several notable MPICH-derived message-passing implementations. MPICH is a high-performance, portable implementation of the MPI-1, MPI-2, and MPI-3 community standards for the message-passing model of parallel computation. Developed by an Argonne team of computer scientists, MPICH has become the de facto standard for scientific research on parallel computers

176

April 2011 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3009 3009 Revision * DOE Standard 1066 Revision * New DOE Standards Projects * Incidents of Security Concern Technical Standard * Explosives Safety * Operations Assessment Field Handbook * Reporting of Radioactive Sealed Sources Program * Occurrence Reporting Causal Analysis Guide * Nuclear Safety-Related Standards Activity INSIDE THIS ISSUE April 2011 Standards Actions Technical Standards Program Newsletter www.hss.energy.gov/nuclearsafety/ns/techstds/ DOE Standard 3009 Revision The Office of Nuclear Safety Policy and Assistance (HS-21), within the Office of Health, Safety and Security (HSS), conducted workshops in January and March to support a major revision of Department of Energy (DOE) Standard 3009, Preparation Guide for U.S. Department of Energy Nonreactor

177

Automated Voltage Standard Ready  

Science Conference Proceedings (OSTI)

... We wanted a standard that was ... as envisioned, then within our lifetimes there will no longer be a need for voltage transfer standards that have to be ...

2013-04-08T23:59:59.000Z

178

complex dimensional standards  

Science Conference Proceedings (OSTI)

... Mailing Address: National Institute of Standards and Technology 100 Bureau Drive ... of CMS Software: NIST-generated data sets, standard level (per ...

2013-06-27T23:59:59.000Z

179

Surrogate protein particle standards  

Science Conference Proceedings (OSTI)

... The large particles may be useful as a standard for the counting of ... drugs require visual inspection, at present there are no standards available for ...

2013-09-10T23:59:59.000Z

180

Appliance Efficiency Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Appliance Efficiency Standards Part 1 of 2 In the National Energy Policy Conservation Act (1978), Congress required DOE to set energy-efficiency standards for 13 residential...

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Cryptographic Standards Statement  

Science Conference Proceedings (OSTI)

... standard. We will continue in our mission to work with the cryptographic community to create the strongest possible encryption standards for the US ...

2013-09-10T23:59:59.000Z

182

Cytomegalovirus Standard Reference Material  

Science Conference Proceedings (OSTI)

... and reagent manufacturers in production of their own calibrants and standards. ... control materials which would be traceable to a NIST standard. ...

2013-03-15T23:59:59.000Z

183

Sustainability Standards Portal  

Science Conference Proceedings (OSTI)

... links to the original standard/ directive developer website ... for harmonizing standards and directives (future work ... for information only; it does not imply ...

184

Battery Standard Scenario  

Science Conference Proceedings (OSTI)

Scenario: Fast Tracking a Battery Standard. ... with developing a new standard specifying quality controls for the development of batteries used in ...

185

Past DOE Technical Standards Program Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Past DOE Technical Standards Program Procedures Past DOE Technical Standards Program Procedures Past DOE Technical Standards Program Procedures TSPP July 2009 September 26, 2009 DOE-TSPP-0, Technical Standards Program Procedures - July 1, 2009 This document is the summary page for all of the DOE Technical Standards Program Procedures. August 26, 2009 DOE-TSPP-1, Technical Standards Program Responsibilities - July 1, 2009 This procedure describes the responsibilities of persons who are charged with implementing the DOE Technical Standards Program. August 26, 2009 DOE-TSPP-2, Establishing the Need for a Technical Standard - July 1, 2009 This procedure provides guidance for the routine maintenance of DOE Technical Standards. August 26, 2009 DOE-TSPP-3, Use of Non-Government Standards and Interaction with Non-Government Standards Bodies - July 1, 2009

186

May 2009 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

May 2009 May 2009 U.S. Department of Energy Technical Standards Program (http://www.hss.energy.gov/nuclearsafety/ns/techstds/) Standards Actions 1.0 DOE STANDARDS ACTIONS The Department of Energy (DOE) Technical Standards Program (TSP) publishes Standards Actions on a monthly basis to provide DOE headquarters and field elements with current information on DOE and select non-government standards activities. The complete list of all DOE Technical Standards projects and their status is available on the TSP web page at: http://www.hss.energy.gov/nuclearsafety/ns/techstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose Projects, Approved Standards, Recently Approved Standards, or Drafts for Review, as

187

February 2009 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

February 2009 February 2009 U.S. Department of Energy Technical Standards Program (http://www.hss.energy.gov/nuclearsafety/ns/techstds/) Standards Actions 1.0 DOE STANDARDS ACTIONS The Department of Energy (DOE) Technical Standards Program (TSP) publishes Standards Actions on a monthly basis to provide DOE headquarters and field elements with current information on DOE and select non-government standards activities. The complete list of all DOE Technical Standards projects and their status is available on the TSP web page at: http://www.hss.energy.gov/nuclearsafety/ns/techstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose Projects, Approved Standards, Recently Approved Standards, or Drafts for Review, as

188

July 2009 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

July 2009 U.S. Department of Energy Technical Standards Program (http://www.hss.energy.gov/nuclearsafety/ns/techstds/) Standards Actions 1.0 DOE STANDARDS ACTIONS The Department of Energy (DOE) Technical Standards Program (TSP) publishes Standards Actions on a monthly basis to provide DOE headquarters and field elements with current information on DOE and select non-government standards activities. The complete list of all DOE Technical Standards projects and their status is available on the TSP web page at: http://www.hss.energy.gov/nuclearsafety/ns/techstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose Projects, Approved Standards, Recently Approved Standards, or Drafts for Review, as

189

May 2010 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

May 2010 U.S. Department of Energy Technical Standards Program (http://www.hss.energy.gov/nuclearsafety/ns/techstds/) Standards Actions 1.0 DOE STANDARDS ACTIONS The Department of Energy (DOE) Technical Standards Program (TSP) publishes Standards Actions on a monthly basis to provide DOE headquarters and field elements with current information on DOE and select non-government standards activities. The complete list of all DOE Technical Standards projects and their status is available on the TSP web page at: http://www.hss.energy.gov/nuclearsafety/ns/techstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose Projects, Approved Standards, Recently Approved Standards, or Drafts for Review, as

190

An Ontology For Standards  

E-Print Network (OSTI)

The paper continues the exploration of standards that the authors initiated in [1] and continued in [2] and [3]. It provides an ontology for standards---a specification of the things and relationships relevant to the topic of standards. The ontology is presented using the ISO standard graphical language, EXPRESS-G. It uses concepts from mathematical logic to clarify the content, meaning, and use of standards. Characteristics and elements of standards that are independent of any particular usage of the standard are defined. The subject matter of standardization is classified and a taxo nomy is presented. Instances of earliest use of each part of the taxonomy are described. The means of establis hing standards is discussed, together with the question of voluntary versus mandatory compliance. The paper closes with a set of conclusions regarding management process standards. The paper concentrates on those aspects of standards of importance to systems engineering, and includes numerous illustrative exa mples.

J. R. Velman; E. R. Widmann

2000-01-01T23:59:59.000Z

191

The Standards Forum, June 1998  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 – June 1998 1 – June 1998 The Standards News on the DOE Technical Standards Program Forum Volume 6 – Number 1 – June 1998 UN I T E D S T A T ES O F A M E R I C A D E P A R T M E N T O F E N E R G Y A Note From the Manager ............. 2 NUREG/CR-6410 ..................... 2 INSIDE THIS ISSUE Avoid Environmental Embarrassments By Suzan L. Jackson and Glen Mondani, Excel Partnership Inc. Reprinted by permission from “Power Engineer- ing,” Vol. 102, No. 1, January 1998. Suzan L. Jackson is business manager of environmental services for Excel Partnership Inc., of Sandy Hook, Connecti- cut. She is the author of “The ISO 14001 Implementation Guide: Creating an Integrated Management System.” Glen Mondani, senior environmental consultant for Excel, was formerly a site environmental manager for Florida Power and Light Co.

192

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Room Air Conditioners Room Air Conditioners Sign up for e-mail updates on regulations for this and other products The Department of Energy (DOE) has regulated the energy efficiency level of residential room air conditioners since 1987. Residential room air conditioners are mounted in windows or through walls and deliver conditioned air to enclosed spaces. Room air conditioners typically extract heat from the room and vent it outdoors. These products are offered in a broad range of sizes and configurations. They are used in homes, apartments, and commercial settings. The standard implemented in 1990 will save approximately 0.7 quads of energy and result in approximately $8 billion in energy bill savings for products shipped from 1990-2019. The standard will avoid about 41.4 million metric tons of carbon dioxide emissions, equivalent to the annual greenhouse gas emissions of about 8.1 million automobiles.

193

NIST Global Standards Information Global Standards News  

Science Conference Proceedings (OSTI)

... (EPRI) to help it develop an interim "roadmap" for determining the architecture and initial key standards for an electric power "Smart Grid". ...

194

Environmental Compliance Functional Area Qualification Standard  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

56-2011 56-2011 June 2011 DOE STANDARD ENVIRONMENTAL COMPLIANCE FUNCTIONAL AREA QUALIFICATION STANDARD DOE Defense Nuclear Facilities Technical Personnel U.S. Department of Energy AREA TRNG Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; further dissemination unlimited. (Unclassified Unlimited) DOE-STD-1156-2011 ii This document is available on the Department of Energy Technical Standards Program Web Site at http://www.hss.energy.gov/nuclearsafety/ns/techstds/ DOE-STD-1156-2011 iv TABLE OF CONTENTS ACKNOWLEDGMENT v PURPOSE 1 APPLICABILITY 1 IMPLEMENTATION 2 EVALUATION REQUIREMENTS 3 INITIAL QUALIFICATION AND TRAINING 5

195

Executive Order 13423 Implementing Instructions  

Energy.gov (U.S. Department of Energy (DOE))

INSTRUCTIONS FOR IMPLEMENTING EXECUTIVE ORDER 13423Strengthening Federal Environmental, Energy, and Transportation Management

196

Standards and Certification  

Science Conference Proceedings (OSTI)

... Standards and Certification. Voluntary Voting System Guidelines (VVSG). The Help America Vote Act instructed the Election ...

2013-09-17T23:59:59.000Z

197

FMOC Standards Program  

NLE Websites -- All DOE Office Websites (Extended Search)

spacer Facilities Management and Operations Center (FMOC) Standards Program (removed) Sandia Home...

198

Standards Development Organization Overview  

Science Conference Proceedings (OSTI)

... Standards Organizations NFPA (National Fire Protection Association) ... Fire News Annual directory NFPA Buyer's Guide ... Headquarters ...

2010-04-28T23:59:59.000Z

199

December 2005 Standards Forum  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Page December 2005 Page December 2005 TSP Manager's Notes 1 Overview of the U.S. Standardization System 2 A Call for Greater Collaboration 5 Technical Standards Manager Spotlight 6 Topical Committee Developments 7 Welcome Aboard the TSMC! 8 DOE Standards Actions 9 Non-Government Standards

200

Blackout Final Implementation Report  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Report Report on the Implementation of the Task Force Recommendations U.S.-Canada Power System Outage Task Force Natural Resources Canada U.S. Department of Energy September 2006 Final Report on the Implementation of the Task Force Recommendations U.S.-Canada Power System Outage Task Force September 2006 Natural Resources Canada U.S. Department of Energy Acknowledgments This document was prepared by staff of Natural Resources Canada and the U.S. Department of Energy. The principal contributors are listed in Annex 1. The staff wish to acknowledge the contributions of the U.S. Federal Energy Regulatory Commission and the Ontario Ministry of Energy. The staff also wish to acknowl- edge the support and cooperation of the North American Electric Reliability Council and, in particular, of Mr. David Nevius, Senior Vice President and Direc- tor of Reliability Assessment & Performance

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

March 2006 Standards Forum and Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 March 2006 1 March 2006 TSP Manager's Notes 1 New ISO Policy Provides International Solutions to Market Needs 2 Plain Talk for a New Generation 5 The Use of Voluntary Consensus Standards within the Department of Energy 7 Two Change Notices for DOE Standard 1104 8

202

February 2013 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 Standards Actions Technical Standards Program Newsletter U . S . D E PA R T M E N T O F O ffi ce O f nuclear SaFety ENERGY inSide thiS iSSue * Featured DOE Technical Standards Activities * DOE Technical Standards Cost- Savings and Access Improvement Initiative * Domestic and International Nuclear Energy Voluntary Consensus Standards Needs * Nuclear Safety- Related Standards Activity Featured dOe technical StandardS activitieS DOE Technical Standards Cost-Savings and Access Improvement Initiative By Helen Todosow, Brookhaven National Laboratory The Department of Energy (DOE) Technical Standards Managers (TSM) are actively exploring ways to save the government and tax payers' money while at the same time significantly improving efficiencies in access and use of voluntary consensus

203

NETL Publication Standards Manual  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards NETL Publication Standards Manual Publication Standards Manual Click on topic below to view Click "Contents" in the bookmarks panel at the left of your screen to return to this page Introduction * Overview * About This Manual - Point of Contact - Download Files - Permission - Signage - Special Applications Publication Standards * Design Elements * Fact Sheets * Font (Typeface) * Full-Size Brochures * Logo * Presentations * Report Covers NETL Publication Standards Manual Overview For over 60 years, we have been at the forefront

204

Puerto Rico - Renewable Energy Portfolio Standard | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Puerto Rico - Renewable Energy Portfolio Standard Puerto Rico - Renewable Energy Portfolio Standard Puerto Rico - Renewable Energy Portfolio Standard < Back Eligibility Utility Savings Category Bioenergy Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Solar Home Weatherization Wind Program Info Program Type Renewables Portfolio Standard Provider Energy Affairs Administration Note: Compliance for this standard does not begin until 2015. Additional rules and regulations are needed to implement this law; this record will be updated periodically as the rules are developed. In July 2010, Puerto Rico enacted the island's first Renewable Energy Portfolio Standard in an effort to spur renewable energy development as well as reduce Puerto Rico's dependence on imported foreign oil (Puerto

205

Renewable Portfolio Standard | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Portfolio Standard Portfolio Standard Renewable Portfolio Standard < Back Eligibility Investor-Owned Utility Savings Category Bioenergy Biofuels Alternative Fuel Vehicles Commercial Heating & Cooling Manufacturing Buying & Making Electricity Hydrogen & Fuel Cells Water Solar Heating & Cooling Water Heating Wind Program Info State New York Program Type Renewables Portfolio Standard Provider New York State Energy Research and Development Authority The New York Public Service Commission (PSC) adopted a renewable portfolio standard (RPS) in September 2004 and issued implementation rules in April 2005. As originally designed, New York's RPS had a renewables target of 25% of state electricity consumption by 2013, but was expanded in January 2010 to 30% by 2015 by order of the PSC. Of this 30%, approximately 20.7% of the

206

CONVERSION OF DOE TECHNICAL STANDARDS TO NON-GOVERNMENT STANDARDS...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CONVERSION OF DOE TECHNICAL STANDARDS TO NON-GOVERNMENT STANDARDS CONVERSION OF DOE TECHNICAL STANDARDS TO NON-GOVERNMENT STANDARDS Purpose This procedure provides guidance on the...

207

Standardized Templates for Reporting Test Results | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appliance & Equipment Standards » Implementation, Certification, & Appliance & Equipment Standards » Implementation, Certification, & Enforcement » Standardized Templates for Reporting Test Results Standardized Templates for Reporting Test Results The Department of Energy (DOE) develops standardized data templates for reporting the results of tests conducted in accordance with current DOE test procedures. Templates may be used by third-party laboratories under contract with DOE that conduct testing in support of ENERGY STAR® verification, DOE rulemakings, and enforcement of the federal energy conservation standards. Standardized DOE Testing Templates Residential Product Templates Automatic Commercial Ice Makers - September 17, 2012 Battery Chargers - June 13, 2011 Beverage Vending Machines - October 25, 2012 Central Air Conditioners and Central Air Conditioning Heat Pumps -

208

August 2001 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7-31-2001 7-31-2001 Activity Summary In Conversion-4 In Preparation-43 Out for Comment-17 Published this Month-0 5-year Review Status Revision in Progress-6 Reaffirmation in Progress-23 Cancellation Pending-4 Cancellation in Progress-12 Proposed for Cancellation-13 No Current Action-11 Inside this issue: DOE Technical Standards Project Initiated 1 DOE Technical Standards Recently Sent for Coordination 1 DOE Technical Standard Recently Reaffirmed 1 DOE Technical Standards Recently Published 2 American National Standards Institute 2 American National Standards 4 American Society for Testing and Materials 5 Visit the Technical Standards Program Web Site at http://tis.eh.doe.gov/techstds/. Standards Actions- August 2001 Standards

209

November 2000 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

November 2000 November 2000 Standards Technical Standards Program Document Status Visit the Technical Standards Program Web Site: http://tis.eh.doe.gov/techstds/ DOE Technical Standards Projects Initiated If you have any questions or are interested in participating in the development of these standards, please contact the representatives listed below. Complete listings of all DOE Technical Standards projects and their status are given on the Technical Standards Pro- gram (TSP) Web Site referenced at the bottom of this page. To access these lists from the home page, click on “DOE Technical Standards,” then click on “Projects” in the left- hand frame to show the links to the project lists. The following DOE Technical Standards projects were recently initiated: • Radiological Control Programs for Special Tritium Compounds, Project Number OCSH-

210

Standards Actions, February 2004  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 DOE Technical Standards Recently Sent for Coordination 1 DOE Technical Standards Recently Published 1 Non-Government Standards 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 5 American Society for Testing and Materials (ASTM) 6 American Nuclear Society (ANS) 11 National Fire Protection Association (NFPA) 12 DOE Technical Standards Program Document Status 01-23-2004 Activity Summary In Conversion - 4 In Preparation - 36 Out for Comment - 23 Published in January - 3 5-year Review Status Revision in Progress - 13 Reaffirmation in Progress - 26 Cancellation Pending - 1 Cancellation in Progress - 3 No Current Action - 0 Inside This Visit the Technical Standards Program

211

July 2005 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE Technical Standards in Reaffirmation 1 DOE Technical Standards Change Notices 1 DOE Technical Standards Recently Published 1 Non-Government Standards Actions 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 DOE Technical Standards Program Document Status 06-28-2005 Activity Summary In Conversion - 4 In Preparation - 21 Out for Comment - 10 Published in June - 2 5-year Review Status Proposed for Revision-6 Revision in Progress-3

212

Nucleic Acid Standards - Standard Ref. Frame  

NLE Websites -- All DOE Office Websites (Extended Search)

Standard Reference Standard Reference Standard Reference Frame Supplemental Information Ideal Geometries X-PLOR Parameters Valence Geometries RNA Ontology Consortium mmCIF Resources PDBML Resources A Standard Reference Frame for the Description of Nucleic Acid Base-pair Geometry A common point of reference is needed to describe the three-dimensional arrangements of bases and base pairs in nucleic acid structures. [1]. For example, parts of a structure, which appear "normal" according to one computational scheme, may be highly unusual according to another and vice versa. It is thus difficult to carry out comprehensive comparisons of nucleic acid structures and to pinpoint unique conformational features in individual structures. In order to resolve these issues, a group of

213

February 2005 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technical Technical Standards Program Document Status 1-18-2005 Activity Summary In Conversion - 4 In Preparation - 25 Out for Comment - 10 Published in January - 3 5-year Review Status Proposed for Revision-6 Revision in Progress-4 Proposed for Reaffirmation-3 Reaffirmation in Progress-21 Cancellation Pending-16 Cancellation in Progress-0 Visit the Technical Standards Program Web Site at http://tis.eh.doe.gov/techstds/ February 2005 Standards Actions 1.0 DOE Standards Actions The complete list of all DOE Technical Standards projects and their status is available on the Technical Standards Program (TSP) web page at http://tis.eh.doe.gov/techstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose Projects,

214

July 2006 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE Technical DOE Technical Standards Program Document Status 06-28-2006 Activity Summary In Conversion - 4 In Preparation - 23 Out for Comment - 14 Published in June - 0 5-year Review Status Proposed for Revision-5 Revision in Progress-6 Proposed for Reaffirmation-1 Reaffirmation in Progress-21 Cancellation Pending-9 Cancellation in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at http://www.eh.doe.gov/ techstds/ July 2006 Standards Actions 1.0 DOE Standards Actions The complete list of all DOE Technical Standards projects and their status is available on the Technical Standards Program (TSP) web page at http://www.eh.doe.gov/techstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose Projects,

215

January 2012 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

* DOE Conduct of Operations Standards Revisions * New DOE Standards Projects * DOE Handbook of Operational Safety and Analysis Techniques * Nuclear Safety- Related Standards Activity INSIDE THIS ISSUE January 2012 Standards Actions Technical Standards Program Newsletter www.hss.energy.gov/nuclearsafety/ns/techstds/ DOE Conduct of Operations Standards Revisions In the early 1990s, the Department of Energy (DOE) developed 17 technical standards to support DOE Order 5480.19, Conduct of Operations Requirements for DOE Facilities. The standards (STDs), listed below, provided examples, good practices, and expanded explanations of the topics in each chapter of the Order. In June 2010, the Order was revised and issued as DOE Order 422.1, Conduct of Operations. The

216

Standard Seawater Comparisons Updated  

Science Conference Proceedings (OSTI)

Salinity adjustments that may reconcile differences in results from different expeditions are presented. These corrections are based upon batch-to-batch differences in Standard Seawater (SSW) after comparison with KC1-derived standards.

Arnold W. Mantyla

1987-04-01T23:59:59.000Z

217

Standard Model Summary  

NLE Websites -- All DOE Office Websites (Extended Search)

resumen del Modelo Standard Avanzar Volver Principal ESTOY PERDIDO Lo que hace que el Modelo Standard sea tan amplio es el hecho que todas las partculas observadas pueden ser...

218

AOCS: supporting international standards  

Science Conference Proceedings (OSTI)

Trade standards improve efficiency of production and ease international commerce. They can also affect profitability. AOCS: supporting international standards inform Magazine algae algal AOCS biomass business chemistry cottonseed date detergents f

219

Standards Actions, July 2001  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6-27-2001 6-27-2001 Activity Summary In Conversion - 4 In Preparation - 42 Out for Comment - 15 Published this Month - 1 5-year Review Status Revision in Progress - 4 Reaffirmation in Progress - 2 Supersedure in Progress - 6 Cancellation Pending - 8 Cancellation in Progress - 2 No Current Action - 35 Inside this issue: DOE Technical Standards Project Initiated 1 DOE Technical Standard Recently Sent for Coordination 1 DOE Technical Standard Recently Published 1 American National Standards Institute 2 American National Standards 3 American Society for Testing and Materials 4 Visit the Technical Standards Program Web Site at http://tis.eh.doe.gov/techstds/. July 2001 Standards Actions DOE Technical Standards Projects Initiated

220

Standards Actions - April 2002  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3-28-2002 3-28-2002 Activity Summary In Conversion - 4 In Preparation - 44 Out for Comment - 13 Published this Month - 2 5-year Review Status Revision in Progress - 4 Reaffirmation in Progress - 2 Supersedure in Progress - 6 Cancellation Pending - 8 Cancellation in Progress - 2 No Current Action - 35 Inside this issue: DOE Technical Standards Project Canceled 1 DOE Technical Standard Recently Sent for Coordination 1 DOE Technical Standards Re- cently Published 2 American National Standards Institute 2 American Society for Testing and Materials International 4 Visit the Technical Standards Program Web Site at http://tis.eh.doe.gov/techstds/. Standards Actions- April 2002 Standards Actions DOE Technical Standards Project Canceled

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

November 2006 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Notices 1 DOE Technical Standards Published 1 Non-Government Standards Actions 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 Publication Staff Roster 2 DOE Technical Standards Program Document Status 10-25-2006 Activity Summary In Conversion - 4 In Preparation - 23 Out for Comment - 16 Published in September - 0 5-year Review Status Proposed for Revision-5 Revision in Progress-6

222

Standard Reference Data  

Science Conference Proceedings (OSTI)

... The National Standard Reference Data System (NSRDS-NBS) provides access to the quantitative data of physical sciences, critically evaluated ...

2013-09-19T23:59:59.000Z

223

Law Enforcement Standards Office  

Science Conference Proceedings (OSTI)

... Talking Police OLES supports the SAFECOM and COPS programs through standards leadership. News. Expanded CSI Guide Now Available. ...

2013-09-20T23:59:59.000Z

224

Related Metrology Standards  

Science Conference Proceedings (OSTI)

... Dynamic measurement -- Proving systems for volumetric meters -- Part 2: Pipe provers. ... Manual of Petroleum Measurement Standards. Contact. ...

2011-10-03T23:59:59.000Z

225

Appendix: Industry Standards  

Science Conference Proceedings (OSTI)

Table 13   Commonly used standards and references for downstream (refining) materials...Practices for the Control

226

Appliance Efficiency Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Appliance Efficiency Standards and Price Discrimination C. Anna Spurlock Energy Analysis & Environmental Impact Department Environmental Energy Technologies Division Lawrence...

227

Challenges in Implementing Methodologies for Nonproliferation Assessments  

Science Conference Proceedings (OSTI)

A handful of models for explaining and predicting States development of nuclear weapons programs have been proposed since the 1970s. Despite the array of techno-social variables and computational concepts employed in these models, no model has yet been established as an agreed-upon standard. Likewise, the International Atomic Energy Agency (IAEA)one of the main institutions evaluating social, political, and technological information for assessments of States current nuclear capabilitiesuses only a qualitative framework by which to evaluate such information to assess the correctness and completeness of a States declaration. In this paper, analysts familiar with both the development of techno-social modelling and the IAEAs implementation of a safeguards system that is information driven discuss the challenges faced in the development, implementation, and evaluation of models and methodologies for nonproliferation assessments, based on experiences at Pacific Northwest National Laboratory (PNNL) and the IAEA.

Gastelum, Zoe N.; Dalton, Angela C.; Coles, Garill A.

2011-07-17T23:59:59.000Z

228

Radiological Control Technician: Standardized technician Qualification Standard  

Science Conference Proceedings (OSTI)

The Qualification Standard states and defines the knowledge and skill requirements necessary for successful completion of the Radiological Control Technician Training Program. The standard is divided into three phases: Phase I concerns RCT Academic training. There are 13 lessons associated with the core academics program and 19 lessons associated with the site academics program. The staff member should sign the appropriate blocks upon successful completion of the examination for that lesson or group of lessons. In addition, facility specific lesson plans may be added to meet the knowledge requirements in the Job Performance Measures (JPM) of the practical program. Phase II concerns RCT core/site practical (JPMs) training. There are thirteen generic tasks associated with the core practical program. Both the trainer/evaluator and student should sign the appropriate block upon successful completion of the JPM. In addition, facility specific tasks may be added or generic tasks deleted based on the results of the facility job evaluation. Phase III concerns the oral examination board successful completion of the oral examination board is documented by the signature of the chairperson of the board. Upon completion of all of the standardized technician qualification requirements, final qualification is verified by the student and the manager of the Radiological Control Department and acknowledged by signatures on the qualification standard. The completed Qualification Standard shall be maintained as an official training record.

Not Available

1992-10-01T23:59:59.000Z

229

Implementing the National Broadband  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Before the Before the Department of Energy Washington, D.C. 20585 In the Matter of Implementing the National Broadband Plan by Studying the Communications Requirements of Electric Utilities To Inform Federal Smart Grid Policy NBP RFI: Communications Requirements COMMENTS OF BALTIMORE GAS & ELECTRIC COMPANY I. Introduction BGE is the nation's oldest and most experienced utility company. It has met the energy needs of central Maryland for nearly 200 years. Today, it serves more than 1.2 million business and residential electric customers, and approximately 650,000 gas customers in an economically diverse, 2,300-square-mile area encompassing Baltimore City and all or part of ten central Maryland counties.

230

Implementing the National Broadband  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DAKOTA ELECTRIC ASSOCIATION DAKOTA ELECTRIC ASSOCIATION I. Introduction a. Identification/description of our company Dakota Electric Association (DEA) is an Incorporated Cooperative Association which distributes electricity to more than 100,000 members in Dakota County and surrounding areas. DEA is the second largest electric cooperative in the state of Minnesota, and is a member cooperative of Great River Energy (GRE). II. Executive Summary DEA has deployed a fully integrated IP network to 26 substation sites. An IP based network transports data information for Supervisory Control and Data Acquisition (SCADA) and Load Management systems. A private Wide Area Network (WAN) was implemented by DEA in 2001 due to lack of comprehensive coverage by major carriers. In addition to the WAN, DEA relies on commercial services to communicate with load

231

Environmental Implementation Plan  

SciTech Connect

The purpose of the Environmental Implementation Plan (EIP) is to show the current and future (five years) environmental plans from individual site organizations and divisions, as well as site environmental programs and initiatives which are designed to protect the environment and meet or exceed changing environmental/regulatory requirements. Communicating with site organizations, departments, and committees is essential in making the site's environmental-planning process work. The EIP gives the site the what, when, how, and why for environmental requirements. Through teamwork and proactive planning, a partnership for environmental excellence is formed to achieve the site vision for SRS to become the recognized model for Environmental Excellence in the Department of Energy's Nuclear Weapons Complex.

Not Available

1993-03-15T23:59:59.000Z

232

Environmental Implementation Plan  

SciTech Connect

The purpose of the Environmental Implementation Plan (EIP) is to show the current and future (five years) environmental plans from individual site organizations and divisions, as well as site environmental programs and initiatives which are designed to protect the environment and meet or exceed changing environmental/regulatory requirements. Communicating with site organizations, departments, and committees is essential in making the site`s environmental-planning process work. The EIP gives the site the what, when, how, and why for environmental requirements. Through teamwork and proactive planning, a partnership for environmental excellence is formed to achieve the site vision for SRS to become the recognized model for Environmental Excellence in the Department of Energy`s Nuclear Weapons Complex.

1993-03-15T23:59:59.000Z

233

Environmental Implementation Plan  

SciTech Connect

The purpose of the Environmental Implementation Plan (EIP) is to show the current and future (five years) environmental plans from individual site organizations and divisions, as well as site environmental programs and initiatives which are designed to protect the environment and meet or exceed changing environmental/regulatory requirements. Communicating with site organizations, departments, and committees is essential in making the site's environmental-planning process work. The EIP gives the site the what, when, how, and why for environmental requirements. Through teamwork and proactive planning, a partnership for environmental excellence is formed to achieve the site vision for SRS to become the recognized model for Environmental Excellence in the Department of Energy's Nuclear Weapons Complex.

1993-03-15T23:59:59.000Z

234

TOWARDS STANDARDIZATION OF CSP YIELD ASSESSMENTS Richard Meyer  

E-Print Network (OSTI)

TOWARDS STANDARDIZATION OF CSP YIELD ASSESSMENTS Richard Meyer 1 , Hans Georg Beyer 2 , Jörg. In the field of concentrating solar power (CSP) standardized procedures for the assessment of energy yields funding for CSP. Other technologies such as wind energy or photovoltaics have already implemented many

Heinemann, Detlev

235

April 2004 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 DOE Technical Standards recently sent for coordination 1 DOE Technical Standards Recently Published 1 Non-Government Standards 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 7 American Society for Testing and Materials (ASTM) 8 American Nuclear Society (ANS) 12 National Fire Protection Association 12 ry DOE Technical Standards Program Document Status 03-26-2004 Activity Summary In Conversion - 4 In Preparation - 37 Out for Comment - 21 Published in March - 2 5-Year Review Status Revision in Progress - 13 Reaffirmation inProgress - 26 Cancellation Pending - 1

236

Standards Actions - August 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards Standards Technical Standards Program Document Status (2000-07-31) (2000-07-31) (2000-07-31) (2000-07-31) (2000-07-31) Activity Summary In Conversion – 4 In Preparation – 32 Out for Comment – 15 Published this Month – 1 5-year Reviews Revisions in Progress – 3 Reaffirmations in Progress – 0 Supersedures in Progress – 6 Cancellations Pending – 8 Cancellations in Progress – 2 No Current Action – 35 Visit the Technical Standards Program Web Site: http://tis.eh.doe.gov/techstds/ DOE Technical Standards Project Initiated If you have any questions or are interested in participating in the development of this standard, please contact the person listed below. Complete listings of all DOE Technical Standards projects and their status are given in the Web Site referenced at the bottom of this page. To access these

237

April 2008 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3-27-2008 3-27-2008 Activity Summary In Conversion - 4 In Preparation - 24 Out for Comment - 26 Published in March - 0 Five Year Review status Proposed for Revision-4 Revision in Progress-3 Proposed for Reaffirmation-0 Reaffirmation in Progress-20 Cancellations Pending-6 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at http://www.hss.energy.gov/nuclear safety/techstds/ April 2008 Standards Actions 1.0 DOE Standards Actions The complete list of all DOE Technical Standards projects and their status is available on the Technical Standards Program (TSP) web page at http://hss.energy.gov/nuclear safetytechstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose

238

IHS Standards Expert  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards » Standards » IHS IHS Standards Expert1354608000000IHS Standards ExpertLANL researchers can access IHS Standards from offsite via Remote Access./No/Question? 667-5809library@lanl.gov IHS Standards Expert LANL researchers can access IHS Standards from offsite via Remote Access. Login For each collection (society), one person may access pdfs at a time, per the Library's subscription license. Please free up the collection for another user when finished: download or print your pdf, then Log Out. FAQs How do I use IHS? IHS Basic Tutorial (pdf) - see more on the "Training & Support" tab within IHS Contact IHS Customer support, 800-447-3352 (our Customer Support ID Number is 5926584) Contact the Research Library at 7-5809 or library@lanl.gov What if full-text is not available?

239

OSHA: Standards and Recordkeeping  

NLE Websites -- All DOE Office Websites (Extended Search)

OSHA: Standards & OSHA: Standards & Record keeping Frances E. Humphrey, CRNP, COHN-5/CM DOE Headquarters January 17, 2002 .. DOL Organizational Chart History of OSHA +11/14n8: Lead Standard Published * 5/23/80: Medical & Exposure Records Standard Finalized * 7/2/82: Voluntary Protection Programs (VPP) Created +11/25/83: HazCom Standard Promulgated * 9/1/89: Lockout/Tagout Standard Issued OSHA Mission Statement * "The mission of the Occupational Safety and Health Administration is to save lives, prevent injuries and protect the health of America's workers" {OSHA, 2001) History of OSHA +12/29nO: President Nixon signed Occupational Safety and Health Act of 1970 * 5129n1: First Standards Adopted * 1/17n2: OSHA Training Institute Established * Nov-Dec 1972: First State Plans Approved

240

Derived Concentration Technical Standard  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

196-2011 196-2011 April 2011 DOE STANDARD DERIVED CONCENTRATION TECHNICAL STANDARD U.S. Department of Energy AREA ENVR Washington, D.C. 20585 Not Measurement Sensitive This document is available on the Department of Energy Technical Standards Program Web Site at http://www.hss.doe.gov/nuclearsafety/ns/techstds/standard/standard.html DOE-STD-1196-2011 ACKNOWLEDGEMENTS This Derived Concentration Technical Standard was a collaborative effort sponsored by the DOE Office of Environmental Policy and Assistance, with support from Department subject matter experts (SMEs) in the field of radiation protection. This standard, which complements DOE Order (O) 458.1, Radiation Protection of the Public and the Environment, was developed taking

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Standards Actions, May 2002  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4-29-2002 4-29-2002 Activity Summary In Conversion - 4 In Preparation - 47 Out for Comment - 12 Published this Month - 6 5-year Review Status Revision in Progress - 10 Reaffirmation in Progress - 12 Supersedure in Progress - 0 Cancellation Pending - 7 Cancellation in Progress - 1 No Current Action - 20 Inside this issue: DOE Technical Standards Proposed for Reaffirmation 1 DOE Technical Standards Re- cently Published 1 American National Standards Institute 2 American Society for Testing and Materials International 4 Visit the Technical Standards Program Web Site at http://tis.eh.doe.gov/techstds/. Standards Actions- May 2002 Standards Actions DOE Technical Standards Proposed for Reaffirmation The following documents are currently being reevaluated under the 5-year

242

May 2008 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4-25-2008 4-25-2008 Activity Summary In Conversion - 4 In Preparation - 24 Out for Comment - 26 Published in April - 2 Five Year Review status Proposed for Revision-4 Revision in Progress-3 Proposed for Reaffirmation-0 Reaffirmation in Progress-20 Cancellations Pending-6 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at http://www.hss.energy.gov/nuclear safety/techstds/ May 2008 Standards Actions 1.0 DOE Standards Actions The complete list of all DOE Technical Standards projects and their status is available on the Technical Standards Program (TSP) web page at http://hss.energy.gov/nuclear safetytechstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose

243

Appliance Efficiency Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

6 6 Appliance Efficiency Standards Part 2 of 2: Policy process and consumer gains Part 1 of this article (CBS News, Spring 1995) discussed LBNL's role in setting federal appliance efficiency standards and presented an overview of the net national benefits of standards. Here, we examine the broader policy context for appliance standards and consumer benefits. Policy Context Appliance efficiency standards provide a minimum requirement for energy efficiency at the point of manufacture (or import). These standards seek to overcome market failures-including price distortions and transaction costs-that have historically given rise to a gap between observed and attainable product efficiencies. In this way, appliance standards complement information programs, utility DSM and other incentive programs,

244

July 2007 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6-27-2007 6-27-2007 Activity Summary In Conversion - 4 In Preparation - 27 Out for Comment - 24 Published in June - 0 5-year Review status Proposed for Revision-5 Revision in Progress-6 Proposed forReaffirmation-1 Reaffirmation in Progress-21 Cancellations Pending-9 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at http://hss.energy.gov/nuclear safetytechstds/ July 2007 Standards Actions 1.0 DOE Standards Actions The complete list of all DOE Technical Standards projects and their status is available on the Technical Standards Program (TSP) web page at http://hss.energy.gov/nuclear safetytechstds/. To access these standards, go to our web page, click on "DOE Technical Standards," then choose

245

Standards Actions - August 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards Standards Technical Standards Program Document Status (2000-07-31) (2000-07-31) (2000-07-31) (2000-07-31) (2000-07-31) Activity Summary In Conversion – 4 In Preparation – 32 Out for Comment – 15 Published this Month – 1 5-year Reviews Revisions in Progress – 3 Reaffirmations in Progress – 0 Supersedures in Progress – 6 Cancellations Pending – 8 Cancellations in Progress – 2 No Current Action – 35 Visit the Technical Standards Program Web Site: http://tis.eh.doe.gov/techstds/ DOE Technical Standards Project Initiated If you have any questions or are interested in participating in the development of this standard, please contact the person listed below. Complete listings of all DOE Technical Standards projects and their status are given in the Web Site referenced at the bottom of this page. To access these

246

Fuel Cell Technologies Office: Plans, Implementation, and Results  

NLE Websites -- All DOE Office Websites (Extended Search)

About About Key Activities Plans, Implementation, & Results Budget Accomplishments Organization Chart & Contacts Quick Links Hydrogen Production Hydrogen Delivery Hydrogen Storage Fuel Cells Technology Validation Codes & Standards Education Systems Analysis Plans, Implementation, and Results The Fuel Cell Technologies Office carries out technology research, development, and deployment through an ongoing process of planning and analysis, implementation, and review. This Web page includes links to documents that support and document the program management process, and the results and public benefits that derive from it. Overview Learn more about this EERE Office. Plans Discover the plans, budgets, and analyses that set the direction of office priorities and activities.

247

Implementing Systems Engineering on a CERCLA Project  

SciTech Connect

The Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), enacted in 1980, provides a regulatory and legal mechanism to reduce risks from prior disposal of hazardous and toxic chemicals. Regulations, Standards, and Guidelines have been published to further define the CERCLA Process. The OU 7-10 Staged Interim Action Project at the Idaho National Engineering and Environmental Laboratory (INEEL) is a CERCLA project working to remediate the pre-1970 disposal pit in which transuranic materials have been disposed. This paper analyzes the CERCLA process from a systems engineering perspective and describes how systems engineering is implemented on this project.

Beitel, George Alois

1999-06-01T23:59:59.000Z

248

Renewables Portfolio Standard | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Renewables Portfolio Standard Renewables Portfolio Standard Renewables Portfolio Standard < Back Eligibility Investor-Owned Utility Retail Supplier Savings Category Bioenergy Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Solar Wind Program Info State New Jersey Program Type Renewables Portfolio Standard Provider New Jersey Board of Public Utilities Note: In July 2012 New Jersey enacted S.B. 1925 substantially revising its solar carve-out. The summary below incorporates information on the changes made to the solar carve-out as well as the qualification of certain hydropower projects under the RPS. While it contains information on many of the most important changes made by the law, it is not exhaustive and lacks some details. Extensive rule making activity will be necessary to implement

249

Alternative Energy Portfolio Standard | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Alternative Energy Portfolio Standard Alternative Energy Portfolio Standard Alternative Energy Portfolio Standard < Back Eligibility Investor-Owned Utility Retail Supplier Savings Category Commercial Heating & Cooling Manufacturing Buying & Making Electricity Bioenergy Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Wind Solar Program Info State Ohio Program Type Renewables Portfolio Standard Provider Ohio Public Utilities Commission '''''Note: Legislation passed in 2012 (S.B. 289 and S.B. 315) added certain new technologies to the list of eligible Renewable Energy Resources and Advanced Energy Resources. In July 2012, The PUCO opened [http://dis.puc.state.oh.us/CaseRecord.aspx?CaseNo=12-2156 Docket 12-2156-EL-ORD] in order to implement the changes. PUCO is accepting comments on the proposed rules, and comments reviewing OAC 4901:1-10, until

250

Energy Efficiency Standard | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Efficiency Standard Energy Efficiency Standard Energy Efficiency Standard < Back Eligibility Investor-Owned Utility Retail Supplier Savings Category Other Program Info State Illinois Program Type Energy Efficiency Resource Standard The 2007 Illinois Power Agency Act (IPAA) requires both electric and natural gas utilities establish annual energy-savings goals and reduce energy delivered and peak demand. Utilities are required to file an energy efficiency and demand-response plan with the Illinois Commerce Commission (ICC) every three years, beginning in 2007. Electric Utility Compliance Electricity Sales Reduction The electricity reduction goals apply to utilities that had 100,000 or more customers on December 31, 2005. In February 2008, the ICC approved utility implementation plans for these requirements, available in Dockets

251

Renewable Energy Standard | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Renewable Energy Standard Renewable Energy Standard Renewable Energy Standard < Back Eligibility Investor-Owned Utility Municipal Utility Retail Supplier Rural Electric Cooperative Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Water Solar Wind Program Info State Michigan Program Type Renewables Portfolio Standard Provider Michigan Public Service Commission '''''Note: The Michigan Public Service Commission (MPSC) created a temporary order ([http://www.dleg.state.mi.us/mpsc/orders/electric/2008/u-15800_12-04-2008... U-15800]) in December of 2008 to address implementation issues for renewable energy and energy optimization plans arising from the passage of PA 295. In March of 2010 the MPSC was granted informal approval of its RPS governing rules by the Michigan State Office of Administrative Hearings and

252

Foreign Obligations Implementation Status Presentation  

National Nuclear Security Administration (NNSA)

January 13, 2004 Crowne Plaza Ravinia Atlanta, January 13, 2004 Crowne Plaza Ravinia Atlanta, January 13, 2004 Crowne Plaza Ravinia Atlanta, Georgia Georgia Obligations Accounting Implementation Workshop Obligations Accounting Implementation Workshop Foreign Obligations Implementation Status Brian G. Horn U.S. Nuclear Regulatory Commission January 13, 2004 Obligations Accounting Implementation Workshop January 13, 2 Obligations Accounting Implementation Workshop January 13, 2004 Crowne Plaza Ravinia Atlanta, GA 004 Crowne Plaza Ravinia Atlanta, GA Overview of Meeting Overview of Meeting * Review how the Obligation Tracking System is working * Presentations: - Review of Government notification procedures - Establishment of the beginning Obligation Balances for sites

253

Process Control System Cyber Security Standards - An Overview  

Science Conference Proceedings (OSTI)

The use of cyber security standards can greatly assist in the protection of critical infrastructure by providing guidelines and requisite imperatives in the implementation of computer-controlled systems. These standards are most effective when the engineers and operators using the standards understand what each of the standards addresses and does not address. This paper provides a review and comparison of ten documents dealing with control system cyber security. It is not meant to be a complete treatment of all applicable standards; rather, this is an exemplary analysis showing the benefits of comparing and contrasting differing documents.

Robert P. Evans; V Stanley Scown; Rolf Carlson; Shabbir Shamsuddin; George Shaw; Jeff Dagle; Paul W Oman; Jeannine Schmidt

2005-10-01T23:59:59.000Z

254

Cost-effectiveness of ASHRAE Standard 90.1-2010 Compared to ASHRAE Standard 90.1-2007  

SciTech Connect

Pacific Northwest National Laboratory (PNNL) completed this project for the U.S. Department of Energys (DOEs) Building Energy Codes Program (BECP). DOEs BECP supports upgrading building energy codes and standards, and the states adoption, implementation, and enforcement of upgraded codes and standards. Building energy codes and standards set minimum requirements for energy-efficient design and construction for new and renovated buildings, and impact energy use and greenhouse gas emissions for the life of buildings. Continuous improvement of building energy efficiency is achieved by periodically upgrading energy codes and standards. Ensuring that changes in the code that may alter costs (for building components, initial purchase and installation, replacement, maintenance and energy) are cost-effective encourages their acceptance and implementation. ANSI/ASHRAE/IESNA Standard 90.1 is the energy standard for commercial and multi-family residential buildings over three floors.

Thornton, Brian A.; Halverson, Mark A.; Myer, Michael; Cho, Hee Jin; Loper, Susan A.; Richman, Eric E.; Elliott, Douglas B.; Mendon, Vrushali V.; Rosenberg, Michael I.

2013-06-18T23:59:59.000Z

255

National Cost-effectiveness of ASHRAE Standard 90.1-2010 Compared to ASHRAE Standard 90.1-2007  

SciTech Connect

Pacific Northwest National Laboratory (PNNL) completed this project for the U.S. Department of Energys (DOEs) Building Energy Codes Program (BECP). DOEs BECP supports upgrading building energy codes and standards, and the states adoption, implementation, and enforcement of upgraded codes and standards. Building energy codes and standards set minimum requirements for energy-efficient design and construction for new and renovated buildings, and impact energy use and greenhouse gas emissions for the life of buildings. Continuous improvement of building energy efficiency is achieved by periodically upgrading energy codes and standards. Ensuring that changes in the code that may alter costs (for building components, initial purchase and installation, replacement, maintenance and energy) are cost-effective encourages their acceptance and implementation. ANSI/ASHRAE/IESNA Standard 90.1 is the energy standard for commercial and multi-family residential buildings over three floors.

Thornton, Brian; Halverson, Mark A.; Myer, Michael; Loper, Susan A.; Richman, Eric E.; Elliott, Douglas B.; Mendon, Vrushali V.; Rosenberg, Michael I.

2013-11-30T23:59:59.000Z

256

Information Technology Standards Choices and Industry Structure Outcomes: The Case of the U.S. Home Mortgage Industry  

Science Conference Proceedings (OSTI)

Vertical IS standards prescribe data structures and definitions, document formats, and business processes for particular industries, in contrast to generic information technology (IT) standards, which concern IT characteristics applicable to many industries. ... Keywords: Adoption, Effects Of Standards, Implementation, Industry Structure, Industry-Level Effects, Is Standards, It Choices, Vertical Standards

Rolf T. Wigand; Charles W. Steinfield

2005-11-01T23:59:59.000Z

257

Environmental Implementation Plan  

SciTech Connect

The Environmental Implementation Plan (EIP) is a dynamic long-range environmental-protection plan for SRS. The EIP communicates the current and future (five year) environmental plans from individual organizations and divisions as well as site environmental initiatives which are designed to protect the environment and meet or exceed compliance with changing environmental/ regulatory requirements. Communication with all site organizations is essential for making the site environmental planning process work. Demonstrating environmental excellence is a high priority embodied in DOE and WSRC policy. Because of your support and participation in the three EIP initiatives; Reflections, Sectional Revision, and Integrated Planning, improvements are being made to the EIP and SRS environmental protection programs. I appreciate the ``Partnership in Environmental Excellence`` formed by the environmental coordinators and professionals who work daily toward our goal of compliance and environmental excellence. I look forward to seeing continued success and improvement in our environmental protection programs through combined efforts of all site organizations to protect our employees, the public health, and the environment. Together, we will achieve our site vision for SRS to be the recognized model for Environmental Excellence in the DOE Nuclear Weapons Complex.

1994-02-01T23:59:59.000Z

258

Standards Actions, October 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Project Initiated Project Initiated If you have any questions or are interested in participating in the development of this standard, please contact the representatives listed below. Complete listings of all DOE Technical Standards projects and their status are given in the Technical Standards Pro- gram (TSP) Web Site referenced at the bottom of this page. To access these lists from the home page, click on “DOE Technical Standards,” then click on “Projects” in the left- hand frame to show the links to the project lists. The following DOE Technical Standards project was recently initiated: • Hoisting and Rigging Standard, Project Number SAFT-0077. This project is being pre- pared by the Hoisting and Rigging Technical Advisory Committee (HRTAC). If you de- sire to participate in this project, please contact your site representative to the HRTAC

259

October 2006 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Publication Staff Roster 2 Publication Staff Roster 2 DOE Technical Standards Program Document Status 09-26-2006 Activity Summary In Conversion - 4 In Preparation - 24 Out for Comment - 16 Published in September - 1 5-year Review Status Proposed for Revision-5 Revision in Progress-6 Proposed for reaffirmation-1 Reaffirmation in Progress-21 Cancellation Pending-9 Cancellation in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at http://www.eh.doe.gov/ techstds/ October 2006 Standards Actions 1.0 DOE Standards Actions The complete list of all DOE Technical Standards projects and their status is available on the Technical Standards Program (TSP) web page at http://www.eh.doe.gov/techstds/. To access

260

Jenseits des Standard Modells  

NLE Websites -- All DOE Office Websites (Extended Search)

The Standard Model The Standard Model Unngelöste Rätsel Jenseits des Standard Modells Das Standard Modell gibt auf viele Fragen, über Struktur und Stabilität der Materie eine Antwort. Dazu braucht es nur die sechs Sorten von Quarks und Leptonen und die vier fundamentalen Kräfte. Aber das Standard Modell ist nicht vollständig; es gibt noch viele unbeantwortete Fragen. Eigentlich sollten wir aus Gründen der Symmetrie im Weltraum gleichviel Materie wie Antimaterie beobachten. Wir finden aber praktisch nur normale Materie! Warum? Woraus besteht die "Dunkle Materie", die wir nicht sehen können, die aber im Universum sichtbare Gravitationswirkungen zeigt? Warum kann das Standard Modell die Massen der Teilchen nicht vorhersagen? Sind Quarks and Leptonen wirklich fundamentae Teilchen, oder sind sie aus noch elementareren Partikeln aufgebaut?

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

February 2001 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards Technical Standards Program Document Status Visit the Technical Standards Program Web Site: http://tis.eh.doe.gov/techstds/ Activity Summary In Conversion - 4 In Preparation - 35 Out for Comment - 18 Published this Month - 1 FY 2001 5-year Reviews Revisions in Progress - 2 Reaffirmations in Progress - 2 Supersedures in Progress - 6 Cancellations Pending - 11 Cancellations in Progress - 33 No Current Action - 16 DOE Technical Standards Project Canceled If you have any questions about this action, please contact the person listed be- low. The following DOE Technical Standards project was recently canceled: * EM Facility Hazard Categorization, Project Number SAFT-0029; EM Technical Standards Manager, John Serocki, 301-903-7999, John.Serocki@em.doe.gov, or Tom Wright, 301-903-3661, Tom.Wright@em.doe.gov. The need for this

262

Technical Standards, 2004 Annual Report - July 29, 2004 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technical Standards, 2004 Annual Report - July 29, 2004 Technical Standards, 2004 Annual Report - July 29, 2004 Technical Standards, 2004 Annual Report - July 29, 2004 July 29, 2004 Fiscal Year 2004, Annual Report to the Office of Management and Budget, Standards use and Participation The Department of Energy (DOE) implements the federal guidance and requirements of OMB Circular A-119 (OMB A-119) and the statutory requirements of Public Law (PL) 104-113 (15 USC 272) regarding the use of voluntary consensus standards (VCSs) through specific Departmental directives (policies, orders, requirements, guides, and technical standards) and supporting programs and management systems. Technical Standards, 2004 Annual Report More Documents & Publications Technical Standards, Office of Management and Budget Report for FY-2012 -

263

Department of Energy Technical Standards Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department Department of Energy Technical Standards Procedures Department of Energy Technical Standards Procedures The following procedures should be used to write, revise, or maintain a DOE technical standard. They are also used to convert a DOE technical standard to a non-government standard or to form a topical committee. TSPP September 2013 September 16, 2013 DOE-TSPP-1-2013, Program Overview and Responsibilities This procedure describes the responsibilities of persons who are charged with implementing the Department of Energy (DOE) Technical Standards Program (TSP). September 16, 2013 DOE-TSPP-2-2013, Initiating DOE Technical Standards This procedure provides guidance on how to establish and justify the need for a Department of Energy (DOE) Technical Standard and register a DOE

264

Appliance and Equipment Standards Result in Large Energy, Economic, and  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appliance and Equipment Standards Result in Large Energy, Economic, Appliance and Equipment Standards Result in Large Energy, Economic, and Environmental Benefits Appliance and Equipment Standards Result in Large Energy, Economic, and Environmental Benefits Saving Consumers and Businesses Energy and Money by Setting Efficiency Standards Saving Consumers and Businesses Energy and Money by Setting Efficiency Standards The Building Technologies Office (BTO) implements minimum energy conservation standards for more than 50 categories of appliances and equipment. As a result of these standards, energy users saved about $40 billion on their utility bills in 2010. Since 2009, 18 new or updated standards have been issued, which will help increase annual savings by more than 50 percent over the next decade. By 2030, cumulative operating cost

265

Energy Efficiency Design Standards for New Federal Commercial and  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Design Standards for New Federal Commercial and Design Standards for New Federal Commercial and Multi-Family High-Rise Residential Buildings Energy Efficiency Design Standards for New Federal Commercial and Multi-Family High-Rise Residential Buildings October 8, 2013 - 1:56pm Addthis Current Standard The U.S. Department of Energy (DOE) has published final rule 10 CFR 433: Energy Efficiency Design Standards for New Federal Commercial and Multi-Family High-Rise Residential Buildings (July 9, 2013) to implement provisions in the Energy Conservation and Production Act (ECPA) that require DOE to update the baseline federal energy efficiency performance standards for the construction of new federal commercial and multi-family high-rise residential buildings. This rule updates the baseline federal commercial standard to ASHRAE Standard 90.1-2010, effective September 9,

266

Appliance Standards and Rulemaking Federal Advisory Committee | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appliance & Equipment Standards » Rulemakings & Notices » Appliance & Equipment Standards » Rulemakings & Notices » Appliance Standards and Rulemaking Federal Advisory Committee Appliance Standards and Rulemaking Federal Advisory Committee The Appliance and Equipment Standards Program established the Appliance Standards and Rulemaking Federal Advisory Committee (ASRAC) in an effort to further improve the Department of Energy's (DOE) process of establishing energy efficiency standards for certain appliances and commercial equipment. ASRAC will allow DOE to use negotiated rulemaking as a means to engage all interested parties, gather data, and attempt to reach consensus on establishing energy efficiency standards. Rules drafted by negotiation may be more pragmatic and implemented at earlier dates than under a more

267

Approved DOE Technical Standards  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

approved-doe-technical-standards Forrestal Building approved-doe-technical-standards Forrestal Building 1000 Independence Avenue, SW Washington, DC 205851.800.dial.DOE en DOE-STD-1150-2013 http://energy.gov/hss/downloads/doe-std-1150-2013 DOE-STD-1150-2013

268

August 2007 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Non-Government Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 Publication Staff Roster 2 DOE Technical Standards Program Document Status 07-27-2007 Activity Summary In Conversion - 4 In Preparation - 27 Out for Comment - 24 Published in June - 0 5-year Review status Proposed for Revision-5 Revision in Progress-6 Proposed for Reaffirmation-1 Reaffirmation in Progress-21 Cancellations Pending-9 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at

269

October 2007 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Non-Government Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 Publication Staff Roster 2 DOE Technical Standards Program Document Status 09-27-2007 Activity Summary In Conversion - 4 In Preparation - 26 Out for Comment - 27 Published in September - 0 5-year Review status Proposed for Revision-5 Revision in Progress-6 Proposed for Reaffirmation-1 Reaffirmation in Progress-21 Cancellations Pending-9 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at

270

April 2005 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Notices 1 Non-Government Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 1 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 DOE Technical Standards Program Document Status 3-28-2005 Activity Summary In Conversion - 4 In Preparation - 25 Out for Comment - 11 Published in March - 0 5-year Review Status Proposed for Revision-6 Revisions in Progress-4 Proposed for Reaffirmation-3 Reaffirmations in Progress-24 Cancellations Pending-11 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards

271

August 2006 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Notices 1 DOE Technical Standards Published 1 Non-Government Standards Actions 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 DOE Technical Standards Program Document Status 07-26-2006 Activity Summary In Conversion - 4 In Preparation - 22 Out for Comment - 16 Published in July - 2 5-year Review Status Proposed for Revision-5 Revision in Progress-6 Proposed for reaffirmation-1 Reaffirmation in Progress-21 Cancellation Pending-9 Cancellation in Progress-0

272

primary frequency standards  

Science Conference Proceedings (OSTI)

NIST-F1 Cesium Fountain Atomic Clock The Primary Time and Frequency Standard for the United States. NIST-F1, the nation's ...

2013-02-04T23:59:59.000Z

273

Particulate Matter Standards (Ohio)  

Energy.gov (U.S. Department of Energy (DOE))

This chapter of the law that establishes the Ohio Environmental Protection Agency sets the standards for particulate emissions from a variety of sources, including facilities that generate power. ...

274

Columbia- Renewables Portfolio Standard  

Energy.gov (U.S. Department of Energy (DOE))

In November 2004, voters in Columbia, Missouri approved a proposal to adopt a local renewables portfolio standard (RPS).* The initiative requires the city's municipal utility, Columbia Water &...

275

Standards for Document Encasement  

Science Conference Proceedings (OSTI)

... time. We want the preservation community to be able to have a common set of standards to develop its own capabilities.. ...

2013-07-02T23:59:59.000Z

276

Vacuum Comparison Standard  

Science Conference Proceedings (OSTI)

... Manometers (UIMs), which are primary standards with the lowest stated uncertainty in the world, but require significant time and money to operate. ...

2012-11-16T23:59:59.000Z

277

Sustainability Standards Portal (SSP)  

Science Conference Proceedings (OSTI)

... A framework for analysis of standards from different perspectives. ... Dr. Jaehyun Lee Dr. Anantha Narayanan Dr. Paul Witherell Dr. Ram D. Sriram Ms ...

2010-11-15T23:59:59.000Z

278

ORISE: Standards development  

NLE Websites -- All DOE Office Websites (Extended Search)

of industry standards that provide guidance and support to decontamination and decommissioning projects across the United States. Because of our extensive experience...

279

Standard Administrative Procedures  

Science Conference Proceedings (OSTI)

... Standards surveillance and instrument monitoring projects. ... are normally stored in a LEVEL 1 security area must never be left unattended when they ...

2010-07-27T23:59:59.000Z

280

USING STANDARD SYSTE  

Science Conference Proceedings (OSTI)

... two-phase region for a symmetric blend ... density mismatch of fluid components and segregation ... Standards and Technology in the flow visualization. ...

2001-07-27T23:59:59.000Z

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Alternative Energy Portfolio Standard  

Energy.gov (U.S. Department of Energy (DOE))

Pennsylvania's Alternative Energy Portfolio Standard (AEPS), created by S.B. 1030 on November 30, 2004, requires each electric distribution company (EDC) and electric generation supplier (EGS) to...

282

Site Lead TQP Standard  

NLE Websites -- All DOE Office Websites (Extended Search)

Qualification Standard for the Office of Safety and Emergency Management Evaluations Site Lead Program May 2011 Office of Enforcement and Oversight Office of Health, Safety and...

283

AND TIME STANDARDS  

Science Conference Proceedings (OSTI)

... mu- tual coupling between the units and to heater thermostat operations. ... resistance-bridge thermostats is planned for use in several new standard ...

2003-01-30T23:59:59.000Z

284

Large Standard Model Chart  

NLE Websites -- All DOE Office Websites (Extended Search)

Standard (tamao mediano) Principal ESTOY PERDIDO Ud puede solicitar una copia REAL de esta hermosa lmina Vea ampliaciones de componentes de la tabla y el texto que...

285

Large Standard Model Chart  

NLE Websites -- All DOE Office Websites (Extended Search)

Tabla del Modelo Standard (tamao mximo) Principal ESTOY PERDIDO Ud puede solicitar una copia REAL de esta hermosa lmina Vea ampliaciones de componentes de la tabla y el...

286

Standard Model Chart  

NLE Websites -- All DOE Office Websites (Extended Search)

Standard Volver Principal ESTOY PERDIDO Usted realmente no necesita memorizar todos los nombres de las partculas, ni cmo interactan, ni sus masas, etc. Sin embargo, a...

287

Fragen zum Standard Modell  

NLE Websites -- All DOE Office Websites (Extended Search)

Quiz What is Fundamental? Fragen zum Standard Modell Frage: Aus wievielen elementaren Teilchen sind die mehr als hundert bekannten Teilchen aufgebaut? Antwort 6 Quarks, 6 Leptonen,...

288

Standard Model Quiz  

NLE Websites -- All DOE Office Websites (Extended Search)

los cientos de partculas conocidas? RESPUESTA: S, 6 quarks, 6 leptones, 6 antiquarks 6 antileptones, y los portadores de fuerza. Regreso a la ruta del Modelo Standard......

289

FEDERAL INFORMATION PROCESSING STANDARDS ...  

Science Conference Proceedings (OSTI)

... This Standard specifies use of a symmetric-key encryption ... definition of "escrow", the key component holders provide the components of a ...

2012-12-20T23:59:59.000Z

290

Standard Reference Materials:  

Science Conference Proceedings (OSTI)

... Statistical analyses of the physical properties from the ... Summary statistics: mean = 118.7 kgm3, standard ... were acquired in 1980 and 1981 for the ...

2012-04-26T23:59:59.000Z

291

SERAPH implementation plans  

DOE Green Energy (OSTI)

The Solar Energy Research Institute (SERI) devotes a significant research effort to the application of solar technology in the industrial sector. It is well known that US industries consume a significant amount of energy, a large portion of which is required in a temperature range in which concentrating solar collectors work effectively. The SERAPH facility (Solar Energy Research and Applications in Process Heat) will provide at SERI the capability of addressing many of the technical issues that currently hamper industrial solar thermal energy system implementation. The primary building blocks of SERAPH are the solar delivery subsystem, control, and data acquisition subsystem (including sequencing and emergency supervision), energy distribution subsystem and two physical areas set aside for storage development and the introduction of load devices. Emphasis has been placed on creating a versatile test facility within which the solar industry can work with SERI in the development of solar systems that will be attractive to potential industrial users. SERAPH will have an initial capability of producing steam at a rate of 900 lb/h (410 kg/h) which corresponds to an energy delivery rate of 1.5 million Btu/h (1.6 x 10/sup 6/ kJ/h) at 430/sup 0/F (220/sup 0/C) with expansion capability to approximately 600/sup 0/F (315/sup 0/C). The initial system controls will be analog with supervisory and direct digital control to follow. The issues to be addressed at SERAPH will be computer predictive model validation and refinement, control strategy development, solar equipment evaluation, and the accumulation of operating and maintenance experience. A consistent theme throughout the planning and operation of SERAPH is the need to develop and follow practices that are consistent with conventional industrial operating procedures.

Castle, J.; Su, W.; Dougherty, D.A.; Wright, J.D.

1979-05-01T23:59:59.000Z

292

10 CFR 850 Implementation of Requirements  

Science Conference Proceedings (OSTI)

10 CFR 850 defines a contractor as any entity, including affiliated entities, such as a parent corporation, under contract with DOE, including a subcontractor at any tier, with responsibility for performing work at a DOE site in furtherance of a DOE mission. The Chronic Beryllium Disease Prevention Program (CBDPP) applies to beryllium-related activities that are performed at the Lawrence Livermore National Laboratory (LLNL). The CBDPP or Beryllium Safety Program is integrated into the LLNL Worker Safety and Health Program and, thus, implementation documents and responsibilities are integrated in various documents and organizational structures. Program development and management of the CBDPP is delegated to the Environment, Safety and Health (ES&H) Directorate, Worker Safety and Health Functional Area. As per 10 CFR 850, Lawrence Livermore National Security, LLC (LLNS) periodically submits a CBDPP to the National Nuclear Security Administration/Livermore Site Office (NNSA/LSO). The requirements of this plan are communicated to LLNS workers through ES&H Manual Document 14.4, 'Working Safely with Beryllium.' 10 CFR 850 is implemented by the LLNL CBDPP, which integrates the safety and health standards required by the regulation, components of the LLNL Integrated Safety Management System (ISMS), and incorporates other components of the LLNL ES&H Program. As described in the regulation, and to fully comply with the regulation, specific portions of existing programs and additional requirements are identified in the CBDPP. The CBDPP is implemented by documents that interface with the workers, principally through ES&H Manual Document 14.4. This document contains information on how the management practices prescribed by the LLNL ISMS are implemented, how beryllium hazards that are associated with LLNL work activities are controlled, and who is responsible for implementing the controls. Adherence to the requirements and processes described in the ES&H Manual ensures that ES&H practices across LLNL are developed in a consistent manner. Other implementing documents, such as the ES&H Manual, are integral in effectively implementing 10 CFR 850.

Lee, S

2012-01-05T23:59:59.000Z

293

FPGA Implementations of the Round Two SHA-3 Candidates  

Science Conference Proceedings (OSTI)

The second round of the NIST-run public competition is underway to find a new hash algorithm(s) for inclusion in the NIST Secure Hash Standard (SHA-3). This paper presents the full implementations of all of the second round candidates in hardware with ... Keywords: SHA-3, HASH, FPGA

Brian Baldwin; Andrew Byrne; Liang Lu; Mark Hamilton; Neil Hanley; Maire O'Neill; William P. Marnane

2010-08-01T23:59:59.000Z

294

Identifying incompatible service implementations using pooled decision trees  

Science Conference Proceedings (OSTI)

We study fault localization techniques for identification of incompatible configurations and implementations in service-based applications (SBAs). Practice has shown that standardized interfaces alone do not guarantee compatibility of services originating ... Keywords: dependability, fault localization, pooled decision trees, service-oriented architecture

Christian Inzinger; Waldemar Hummer; Benjamin Satzger; Philipp Leitner; Schahram Dustdar

2013-03-01T23:59:59.000Z

295

Applying Grounded Theory to Understand Software Process Improvement Implementation  

Science Conference Proceedings (OSTI)

Recent studies show that many organizations struggle to implement Software Process Improvement (SPI) based on process models and standards mainly because of incapacity to overcome critical barriers, such as lack of motivation and higher management support. ... Keywords: Grounded Theory, Software Process Improvement (SPI)

Mariano Angel Montoni; Ana Regina Rocha

2010-09-01T23:59:59.000Z

296

Design, implementation and testing of extended and mixed precision BLAS  

Science Conference Proceedings (OSTI)

This article describes the design rationale, a C implementation, and conformance testing of a subset of the new Standard for the BLAS (Basic Linear Algebra Subroutines): Extended and Mixed Precision BLAS. Permitting higher internal precision and mixed ... Keywords: BLAS, double-double arithmetic, extended and mixed precision

Xiaoye S. Li; James W. Demmel; David H. Bailey; Greg Henry; Yozo Hida; Jimmy Iskandar; William Kahan; Suh Y. Kang; Anil Kapur; Michael C. Martin; Brandon J. Thompson; Teresa Tung; Daniel J. Yoo

2002-06-01T23:59:59.000Z

297

Journeys Beyond the Standard Model  

E-Print Network (OSTI)

Chapter 1 Introduction The Standard Model (SM) of Particleresults of searches for the standard model Higgs boson in ppunderstand new physics. The Standard Model is incom- plete;

Elor, Gilly

2013-01-01T23:59:59.000Z

298

Understanding Service Systems Through Standards  

E-Print Network (OSTI)

T. 2004. Economics of Standards in Information Networks.Kindleberger, C. P. 1983. Standards as Public, Collectivethe nature of today's standards. Presented at the

Mathew, Ashwin J.

2008-01-01T23:59:59.000Z

299

Nucleic Acid Standards - Standard Ref. Frame  

NLE Websites -- All DOE Office Websites (Extended Search)

A Standard Reference Frame for the Description A Standard Reference Frame for the Description of Nucleic Acid Base-pair Geometry Supplementary Material The report is available at Journal of Molecular Biology (2001) 313: 229 - 237 and The Nucleic Acid Cartesian coordinates for A, C, G, T, and U in the optimized reference frame Adenine, Cytosine, Guanine, Thymine, Uracil Standard chemical structures taken from Clowney et al. (1996), J. Am. Chem. Soc., 118, 509-518). These data do not include C1' atoms, which are placed here in the least-squares plane of the base atoms, with the purine C1'-N9 bond length and C1'-N9-C4 valence angle set respectively to 1.46 Å and 126.5° and the pyrimidine C1'-N1 bond and C1-N1-C2 angle to 1.47 Å and 118.1°. These distances and angles are based on the average glycosyl

300

Former Worker Medical Screening Program Implementation | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Former Worker Medical Screening Program Implementation Former Worker Medical Screening Program Implementation Program implementation focuses on four specific activities, which are:...

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Electricity Policy Coordination and Implementation | Department...  

NLE Websites -- All DOE Office Websites (Extended Search)

Implementation Electricity Policy Coordination and Implementation OE is laying the framework for a modern electricity system by contributing to the development and implementation...

302

NEPA Implementation | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementation Implementation NEPA Implementation Selected documents providing guidance on the implementation of NEPA. September 7, 2012 OMB and CEQ Joint Memorandum on Environmental Collaboration and Conflict Resolution This Office of Management and Budget (OMB) and Council on Environmental Quality (CEQ) joint memorandum expands and builds on the November 28, 2005, Environmental Conflict Resolution (ECR) Memorandum, directing departments and agencies to increase the appropriate and effective use of third-party assisted environmental collaboration as well as environmental conflict resolution to resolve problems and conflicts that arise in the context of environmental, public lands, or natural resources issues, including matters related to energy, transportation, and water and land management.

303

Educational Technology| Leadership and Implementation.  

E-Print Network (OSTI)

?? The purpose of this study was to evaluate two important aspects of educational technology: leadership and implementation. The research conducted in this study aimed (more)

Galla, Anthony J.

2011-01-01T23:59:59.000Z

304

NMR implementations of Gauss sums  

E-Print Network (OSTI)

I describe the use of NMR experiments which implement Gauss sums as a method for factoring numbers and discuss whether this approach can be computationally useful.

Jonathan A. Jones

2008-07-10T23:59:59.000Z

305

IMPLEMENTATION GUIDANCE | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

detailed operational procedures used to implement the Department of Energy (DOE) Procedural Rules for the Assessment of Civil Penalties for Classified Information Security...

306

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Residential Furnaces and Boilers Residential Furnaces and Boilers Sign up for e-mail updates on regulations for this and other products The Department of Energy (DOE) has regulated the energy efficiency level of residential furnaces and boilers since 1987. Residential furnaces and boilers include gas, electric, and oil-fired furnaces and boilers that are used to provide central heating to residential dwellings. Furnaces heat air and distribute the heated air through the house using ducts. Boilers heat water, providing either hot water or steam for heating. Steam is distributed via pipes to steam radiators, and hot water can either be distributed via baseboard radiators, radiant floor systems, or can heat air via a coil. The standards for residential furnaces and boilers implemented in 1992 will save approximately 3.9 quads of energy and result in approximately $46.2 billion in energy bill savings for products shipped from 1992-2021. The standard will avoid about 206 million metric tons of carbon dioxide emissions, equivalent to the annual greenhouse gas emissions of about 40.4 million automobiles.

307

June 2006 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Page 1 June 2006 Page 1 June 2006 Technical Standards Program Manager's Note 1 Safety for Electrical Workers 2 Significant Federal Laws and Policies 3 Clearance of Solid Materials from Nuclear Facilities 5 Technical Standards Manager Spotlight 6 Topical Committee Developments 7 From the ANSI Web site 8 Don't Get "Board" With

308

C# Annotated Standard  

Science Conference Proceedings (OSTI)

Standards, while being definitive, do not usually serve as the best reference to the use of a programming language. Books on languages usually are able to explain usage better, but lack the definitive precision of a standard. This book combines the two; ... Keywords: C#, Computer Science, Programming, Programming Languages

Jon Jagger; Nigel Perry; Peter Sestoft

2007-07-01T23:59:59.000Z

309

Standards Development as Hybridization  

Science Conference Proceedings (OSTI)

While users in the rest of the World have been offered 3G mobile phones based on either the CDMA2000 or W-CDMA standards, users in China have the additional option of using phones based on the TD-SCDMA standard. As a technology largely developed by Chinese ... Keywords: Global, Hybridization, Indigenous, Innovation, Mobile Phones, National, Technology

Xiaobai Shen, Ian Graham, James Stewart, Robin Williams

2013-07-01T23:59:59.000Z

310

Global residential appliance standards  

SciTech Connect

In most countries, residential electricity consumption typically ranges from 20% to 40% of total electricity consumption. This energy is used for heating, cooling, refrigeration and other end-uses. Significant energy savings are possible if new appliance purchases are for models with higher efficiency than that of existing models. There are several ways to ensure or encourage such an outcome, for example, appliance rebates, innovative procurement, and minimum efficiency standards. This paper focuses on the latter approach. At the present time, the US is the only country with comprehensive appliance energy efficiency standards. However, many other countries, such as Australia, Canada, the European Community (EC), Japan and Korea, are considering enacting standards. The greatest potential impact of minimum efficiency standards for appliances is in the developing countries (e.g., China and India), where saturations of household appliances are relatively low but growing rapidly. This paper discusses the potential savings that could be achieved from global appliance efficiency standards for refrigerators and freezers. It also could be achieved from global appliance efficiency standards for refrigerators and freezers. It also discusses the impediments to establishing common standards for certain appliance types, such as differing test procedures, characteristics, and fuel prices. A methodology for establishing global efficiency standards for refrigerators and freezers is described.

Turiel, I.; McMahon, J.E. [Lawrence Berkeley Lab., CA (US); Lebot, B. [Agence Francaise pour la Maitrise de l`Energie, Valbonne (FR)

1993-03-01T23:59:59.000Z

311

Universal software safety standard  

Science Conference Proceedings (OSTI)

This paper identifies the minimum subset required for a truly universal safety-critical software standard. This universal software standard could be used in but is not limited to the following application domains: commercial, military and space ... Keywords: software safety, system safety, validation, verification

P. V. Bhansali

2005-09-01T23:59:59.000Z

312

MODEL CONSERVATION STANDARD INTRODUCTION  

E-Print Network (OSTI)

standards and surcharge methodology. 2 The term "system cost" means an estimate of all direct costs and transmission to the consumer and, among other factors, waste disposal costs, end-of-cycle costs, and fuel costs. SURCHARGE RECOMMENDATION The Council does not recommend that the model conservation standards be subject

313

Hydrogen Codes and Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Codes and Standards Codes and Standards James Ohi National Renewable Energy Laboratory 1617 Cole Blvd. Golden, CO 80401 Background The development and promulgation of codes and standards are essential if hydrogen is to become a significant energy carrier and fuel because codes and standards are critical to establishing a market-receptive environment for commercializing hydrogen-based products and systems. The Hydrogen, Fuel Cells, and Infrastructure Technologies Program of the U.S. Department of Energy (DOE) and the National Renewable Energy Laboratory (NREL), with the help of the National Hydrogen Association (NHA) and other key stakeholders, are coordinating a collaborative national effort by government and industry to prepare, review, and promulgate hydrogen codes and standards needed to expedite hydrogen infrastructure development. The

314

The Standards Forum and Standards Actions - June 2001 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The Standards Forum and Standards Actions - June 2001 The Standards Forum and Standards Actions - June 2001 The Standards Forum and Standards Actions - June 2001 The Standards Forum and Standards Actions - June 2001 Inside this issue: Should DOE Organizations Include DOE O 252.1 in their Contracts?....................................................... 1 Metrology/Accreditation Personnel and Nuclear Weapons Complex Managers Take Action Addressing Current Issues at Joint Annual Meeting........................................................................ 1 A Note from the Manager........................................................................................................................ 2 Welcome Aboard the TSMC!..................................................................................................................

315

Environmental Restoration Quality Program Implementation Plan. Environmental Restoration Program  

SciTech Connect

The Environmental Restoration (ER) Program requirements for implementation of DOE Order 5700.6C are identified in the Environmental Restoration Quality Program Plan, (QPP). Management systems necessary to implement the ER QPP consist of the necessary standards and procedures required to be developed to adequately control ER processes. To the extent possible, Martin Marietta Energy Systems, Inc., standards and procedures will be utilized at the ER Program level, and requirements will not be repeated. The quality management systems identified for enhancement or development are identified in the section on Procedure Development Strategy and directly relate to unique ER Program activities. Procedures and standards that currently exist in the ER Program will be validated for compliance with ER QPP requirements.

1992-08-01T23:59:59.000Z

316

1997 DOE technical standards program workshop: Proceedings  

Science Conference Proceedings (OSTI)

The Department of Energy held its annual Technical Standards Program Workshop on July 8--10, 1997, at the Loews L`Enfant Plaza Hotel in Washington, DC. The workshop focused on aspects of implementation of the National Technology Transfer and Advancement Act of 1995 [Public Law (PL) 104-113] and the related revision (still pending) to OMB Circular A119 (OMB A119), Federal Participation in the Development and Use of Voluntary Standards. It also addressed DOE`s efforts in transitioning to a standards-based operating culture, and, through this transition, to change from a developer of internal technical standards to a customer of external technical standards. The workshop was designed to provide a forum to better understand how the new law is affecting Department activities. Panel topics such as ``Public Law 104-113 and Its Influence on Federal Agency Standards Activities`` and ``Update on Global Standards Issues`` provided insight on both the internal and external effects of the new law. Keynote speaker Richard Meier of Meadowbrook International (and formerly the Deputy Assistant US Trade Representative) addressed the subject of international trade balance statistics. He pointed out that increases in US export figures do not necessarily indicate increases in employment. Rather, increased employment results from product growth. Mr Meier also discussed issues such as the US migration to the sue of the metric system, the impact of budget limitations on Government participation in voluntary standards organizations, international standards ISO 9000 and ISO 14000, and DOE`s role in the worldwide transition from weapons production to cleanup.

NONE

1997-10-01T23:59:59.000Z

317

Implementation Report: Energy Conservation Activities  

NLE Websites -- All DOE Office Websites (Extended Search)

to Section 141 of the to Section 141 of the Energy Policy Act of 2005 U.S. Department of Energy February 2007 Table of Contents List of Acronyms .............................................................................................................. 3 Introduction ...................................................................................................................... 4 State of New York, et al. v. Bodman; and NRDC, Inc. et al v. Bodman ............................ 5 Multi-Year Schedule and Implementation Update..................................................... 6 Multi-Year Schedule....................................................................................................... 6 Implementation Update .................................................................................................. 9

318

Implementation Report: Energy Conservation Activities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

to Section 141 of the to Section 141 of the Energy Policy Act of 2005 U.S. Department of Energy February 2007 Table of Contents List of Acronyms .............................................................................................................. 3 Introduction ...................................................................................................................... 4 State of New York, et al. v. Bodman; and NRDC, Inc. et al v. Bodman ............................ 5 Multi-Year Schedule and Implementation Update..................................................... 6 Multi-Year Schedule....................................................................................................... 6 Implementation Update .................................................................................................. 9

319

Biofuel and Bioenergy implementation scenarios  

E-Print Network (OSTI)

Biofuel and Bioenergy implementation scenarios Final report of VIEWLS WP5, modelling studies #12;Biofuel and Bioenergy implementation scenarios Final report of VIEWLS WP5, modelling studies By André of this project are to provide structured and clear data on the availability and performance of biofuels

320

Molecular Implementation of Combinatory Computing  

E-Print Network (OSTI)

Molecular Implementation of Combinatory Computing for Nanostructure Synthesis and Control: Progress Molecular combinatory computing makes use of a small set of chemical re- actions that together have by several simulated nano-assembly applications, and discuss a possible molecular implementation in terms

MacLennan, Bruce

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Implementing an Operator Excellence Program  

Science Conference Proceedings (OSTI)

This document is designed to offer power plant operations staff the essential elements that EPRI believes are necessary to effectively implement a successful Operator Excellence Program (OEP). The elements consist of the following: Creation of an OEP implementation team Project management considerations Blended training program considerations Qualification and certification considerations An effective quality assurance program

2002-12-29T23:59:59.000Z

322

NIST: Neutron Cross Section Standards  

Science Conference Proceedings (OSTI)

... standards. Description: Measurements have been completed at Ohio University of the important hydrogen scattering angular distribution standard ...

2013-07-30T23:59:59.000Z

323

Materials Standards for Additive Manufacturing  

Science Conference Proceedings (OSTI)

... ASTM F2924 Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion) except for standards ...

2013-06-04T23:59:59.000Z

324

Calibration Procedures: Standard Operating Procedures  

Science Conference Proceedings (OSTI)

... 18, Calibration of Graduated Neck-Type Metal Volumetric Field Standards, Volumetric Transfer Method Revision ... 20, Standard Deviation and Range ...

2013-09-03T23:59:59.000Z

325

DNA Profiling Standard Reference Materials  

Science Conference Proceedings (OSTI)

... agreement with the NIST Office of Law Enforcement Standards. ... Related Programs and Projects: SRM 2372 - Human DNA Quantitation Standard. ...

2013-03-15T23:59:59.000Z

326

Medical Devices Metrology and Standards  

Science Conference Proceedings (OSTI)

... Medical Devices Metrology and Standards Needs (Download the flyer in pdf ... Standard and Metrology Needs for Surgical Robotics, presented by ...

2013-07-18T23:59:59.000Z

327

Radioactivity Standard Reference Material Program  

Science Conference Proceedings (OSTI)

... Summary: The Standard Reference Materials Program of the National Institute of Standards and Technology (NIST) provides science, industry, and ...

2013-03-27T23:59:59.000Z

328

Examples of Smart Grid Standards  

Science Conference Proceedings (OSTI)

... Examples of Smart Grid Standards. Hundreds of standards will be required for an efficient and effective smart grid. Historically ...

2013-05-09T23:59:59.000Z

329

January 2008 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 Publication Staff Roster 2 DOE Technical Standards Program Document Status 12-27-2007 Activity Summary In Conversion - 4 In Preparation - 22 Out for Comment - 26 Published in December - 4 5-year Review status Proposed for Revision-5 Revision in Progress-6 Proposed for Reaffirmation-1 Reaffirmation in Progress-21 Cancellations Pending-9 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at http://www.hss.energy.gov/nuclear safety/techstds/

330

November 2007 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 Publication Staff Roster 2 DOE Technical Standards Program Document Status 10-29-2007 Activity Summary In Conversion - 4 In Preparation - 24 Out for Comment - 30 Published in October - 0 5-year Review status Proposed for Revision-5 Revision in Progress-6 Proposed for Reaffirmation-1 Reaffirmation in Progress-21 Cancellations Pending-9 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at http://hss.energy.gov/nuclear safetytechstds/

331

Mechanical Systems Qualification Standard  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

61-2008 61-2008 June 2008 DOE STANDARD MECHANICAL SYSTEMS QUALIFICATION STANDARD DOE Defense Nuclear Facilities Technical Personnel U.S. Department of Energy AREA TRNG Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. DOE-STD-1161-2008 ii This document is available on the Department of Energy Technical Standards Program Web Site at http://www.hss.energy.gov/nuclearsafety/techstds/ DOE-STD-1161-2008 iv INTENTIONALLY BLANK DOE-STD-1161-2008 v TABLE OF CONTENTS ACKNOWLEDGMENT................................................................................................................ vii PURPOSE ....................................................................................................................................1

332

February 2008 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society (ANS) 2 National Fire Protection Association (NFPA) 2 Publication Staff Roster 2 DOE Technical Standards Program Document Status 01-28-2008 Activity Summary In Conversion - 4 In Preparation - 22 Out for Comment - 24 Published in January - 3 5-year Review status Proposed for Revision-5 Revision in Progress-6 Proposed for Reaffirmation-1 Reaffirmation in Progress-21 Cancellations Pending-9 Cancellations in Progress-0 Inside This Issue Visit the Technical Standards Program Web Site at http://www.hss.energy.gov/nuclear safety/techstds/

333

Standard for solar collectors  

SciTech Connect

The purpose of this standard is to estabish for solar collectors: definitions; requirements for testing and rating; specifications, literature and advertising requirements; requirements for marking; requirements for safety; and conformance conditions. This standard is intended for the guidance of the industry including manufacturers, engineers, distributors, installers, contractors, and consumers. This standard applies to factory-made solar collectors using either air or a liquid as the heat transfer fluid for one or more of the following purposes: a) heating service water or other fluids and b) heating or cooling of buildings.

1977-01-01T23:59:59.000Z

334

Sonication standard laboratory module  

DOE Patents (OSTI)

A standard laboratory module for automatically producing a solution of cominants from a soil sample. A sonication tip agitates a solution containing the soil sample in a beaker while a stepper motor rotates the sample. An aspirator tube, connected to a vacuum, draws the upper layer of solution from the beaker through a filter and into another beaker. This beaker can thereafter be removed for analysis of the solution. The standard laboratory module encloses an embedded controller providing process control, status feedback information and maintenance procedures for the equipment and operations within the standard laboratory module.

Beugelsdijk, Tony (Los Alamos, NM); Hollen, Robert M. (Los Alamos, NM); Erkkila, Tracy H. (Los Alamos, NM); Bronisz, Lawrence E. (Los Alamos, NM); Roybal, Jeffrey E. (Santa Fe, NM); Clark, Michael Leon (Menan, ID)

1999-01-01T23:59:59.000Z

335

DOE technical standards list. Department of Energy standards index  

Science Conference Proceedings (OSTI)

This document was prepared for use by personnel involved in the selection and use of DOE technical standards and other Government and non-Government standards. This TSL provides listing of current DOE technical standards, non-Government standards that have been adopted by DOE, other Government documents in which DOE has a recorded interest, and canceled DOE technical standards. Information on new DOE technical standards projects, technical standards released for coordination, recently published DOE technical standards, and activities of non-Government standards bodies that may be of interest to DOE is published monthly in Standards Actions.

NONE

1995-08-01T23:59:59.000Z

336

CRAD, Chemical Management Implementation - June 30, 2011 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Chemical Management Implementation - June 30, 2011 Chemical Management Implementation - June 30, 2011 CRAD, Chemical Management Implementation - June 30, 2011 June 30, 2011 Chemical Management Implementation Inspection Criteria, Approach, and Lines of Inquiry (HSS CRAD 45-31, Rev. 1) This document provides an overview of the Criteria, Activities, and Lines of Inquiry that will be used to collect information to evaluate the chemical management against DOE policy, regulatory requirements. Primary attention will be given to activities governed by the Occupational Safety and Health Administration's Hazard Communication Standards (29 CFR 1910.1200 and 29 CFR 1926.59) and Occupational Exposure to Chemicals in Laboratories (29 CFR 1910.1450). However, review of any activities for managing, storing, or using hazardous chemicals, pesticides, and toxic

337

CRAD, Chemical Management Implementation - June 30, 2011 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Chemical Management Implementation - June 30, 2011 Chemical Management Implementation - June 30, 2011 CRAD, Chemical Management Implementation - June 30, 2011 June 30, 2011 Chemical Management Implementation Inspection Criteria, Approach, and Lines of Inquiry (HSS CRAD 45-31, Rev. 1) This document provides an overview of the Criteria, Activities, and Lines of Inquiry that will be used to collect information to evaluate the chemical management against DOE policy, regulatory requirements. Primary attention will be given to activities governed by the Occupational Safety and Health Administration's Hazard Communication Standards (29 CFR 1910.1200 and 29 CFR 1926.59) and Occupational Exposure to Chemicals in Laboratories (29 CFR 1910.1450). However, review of any activities for managing, storing, or using hazardous chemicals, pesticides, and toxic

338

The Standards Forum, Volume 8 - Number 1 - June 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 – June 2000 1 – June 2000 PAGE 1 The Standards News on the DOE Technical Standards Program A Note From the Manager ............. 2 Seven Years of Service .................. 2 INSIDE THIS ISSUE TSM Spotlight ................................ 3 Lessons Learned ............................ 5 Standards Training Opportunities ... 5 Standards Actions .......................... 6 Topical Committees ....................... 10 RevCom ........................................ 12 News Briefs ................................... 13 New TSM, FAQs ........................... 15 Upcoming Meetings ....................... 16 Volume 8 – Number 1 – June 2000 On March 15, 2000, representatives from four Federal agen- cies testified on the implementation and coordination of Section 12 of the National Technology Transfer and Advancement Act

339

USE OF VOLUNTARY CONSENSUS STANDARDS AND INTERACTION WITH STANDARDS  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

USE OF VOLUNTARY CONSENSUS STANDARDS AND INTERACTION WITH STANDARDS USE OF VOLUNTARY CONSENSUS STANDARDS AND INTERACTION WITH STANDARDS DEVELOPMENT ORGANIZATIONS USE OF VOLUNTARY CONSENSUS STANDARDS AND INTERACTION WITH STANDARDS DEVELOPMENT ORGANIZATIONS Purpose This procedure identifies the process by which DOE adopts Voluntary Consensus Standards (VCSs) and provides guidance for the interaction of DOE and contractor employees with Standards Development Organizations (SDOs). Use of Voluntary Consensus Standards and Interaction with Standards Development Organizations (TSPP-03) More Documents & Publications DOE-TSPP-3, Use of Voluntary Consensus Standards and Interaction with Standards Development Organizations - August 1, 2000 DOE-TSPP-3, Use of Non-Government Standards and Interaction with Non-Government Standards Bodies - July 1, 2009

340

DOE technical standards list: Department of Energy standards index  

Science Conference Proceedings (OSTI)

This Department of Energy (DOE) technical standards list (TSL) has been prepared by the Office of Nuclear Safety Policy and Standards (EH-31) on the basis of currently available technical information. Periodic updates of this TSL will be issued as additional information is received on standardization documents being issued, adopted, or canceled by DOE. This document was prepared for use by personnel involved in the selection and use of DOE technical standards and other Government and non-Government standards. This TSL provides listings of current DOE technical standards, non-Government standards that have been adopted by DOE, other standards-related documents in which DOE has a recorded interest, and canceled DOE technical standards. Information on new DOE technical standards projects, technical standards released for coordination, recently published DOE technical standards, and activities of non-Government standards bodies that may be of interest to DOE is published monthly in Standards Actions.

NONE

1999-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

EP&R Standards Project Report: Technical Review of National Incident Management Standards  

SciTech Connect

The importance and necessity for a fully developed and implemented National Incident Management System (NIMS) has been demonstrated in recent years by the impact of national events such as Hurricane Katrina in 2005. Throughout the history of emergency response to major disasters, especially when multiple response organizations are involved, there have been systemic problems in the consistency and uniformity of response operations. Identifying national standards that support the development and implementation of NIMS is key to helping solve these systemic problems. The NIMS seeks to provide uniformity and consistency for incident management by using common terminology and protocols that will enable responders to coordinate their efforts to ensure an efficient response.

Stenner, Robert D.

2007-04-24T23:59:59.000Z

342

Title Standards 2001  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards 2001 Standards 2001 A guide for the preparation of title evidence in land acquisitions by the United States of America. Quick links to Contents: Table of Contents / Why Title Standards 2001, and who uses it? / Evidence of title / Abstract of Title Supplemental and Supporting Title Evidence / Title Insurance Policies and Certificates of Title / Final Title Evidence Title Evidence for Condemnations / The Deed to the United States / Special Standards for Texas / Sample Forms U.S. Department of Justice Environment and Natural Resources Division Land Acquisition Section Washington, D.C. 20530 December 29, 2000 (reprint March 23, 2001) [Editor's Note: The reprint of March 23, 2001, added page numbers to the table of contents; added a new item "3" to part B of Form # 1 of the Certificate of Inspection and Possession,

343

Standards-Developing Organizations  

Science Conference Proceedings (OSTI)

Table 1   Source of codes and standards related to brazing...749 01 11 Web site: www.iso.ch National Board of Boiler and Pressure Vessel

344

Roundness calibration standard  

DOE Patents (OSTI)

A roundness calibration standard is provided with a first arc constituting the major portion of a circle and a second arc lying between the remainder of the circle and the chord extending between the ends of said first arc.

Burrus, B.M.

1982-01-29T23:59:59.000Z

345

Roundness calibration standard  

DOE Patents (OSTI)

A roundness calibration standard is provided with a first arc constituting the major portion of a circle and a second arc lying between the remainder of the circle and the chord extending between the ends of said first arc.

Burrus, Brice M. (6620 Wachese La., Knoxville, TN 37912)

1984-01-01T23:59:59.000Z

346

FREIGHT CONTAINER LIFTING STANDARD  

Science Conference Proceedings (OSTI)

This standard details the correct methods of lifting and handling Series 1 freight containers following ISO-3874 and ISO-1496. The changes within RPP-40736 will allow better reading comprehension, as well as correcting editorial errors.

POWERS DJ; SCOTT MA; MACKEY TC

2010-01-13T23:59:59.000Z

347

EPCglobal : a universal standard  

E-Print Network (OSTI)

This thesis evaluates the likelihood of EPCglobal becoming the universal RFID standard by presenting a framework of ten factors used to analyze and determine if EPCglobal is moving in the right direction. The ten factors ...

Aguirre, Juan Ignacio

2007-01-01T23:59:59.000Z

348

Quality Standards for Abstracts  

Science Conference Proceedings (OSTI)

QUALITY STANDARDS FOR ABSTRACTS American Oil Chemists Society (AOCS) An abstract allows you to concisely convey to the scientific community the value and importance of your research. Its restricted length allows the reader to quickly eva

349

Drinking Water Standards  

E-Print Network (OSTI)

This publication explains the federal safety standards for drinking water provided by public water supply systems. It discusses the legal requirements for public water supplies, the maximum level allowed for contaminants in the water, and the potential health effects of each contaminant regulated. People who use water from private sources such as wells can also use these standards as a guide in checking whether their water is safe.

Dozier, Monty; McFarland, Mark L.

2006-04-26T23:59:59.000Z

350

SAE Standards Support  

Science Conference Proceedings (OSTI)

This report summarizes PNNL activities in FY 2012 in support of the following two vehicle communication standards activities: Technical support to SAE, ANSI and NIST technical working groups. PNNL actively contributed to the use case development, harmonization, and evaluation of the SAE standards activities for vehicle to grid communication Tested and validated a set of potential technologies for meeting SAE communication requirements and provided recommendations for technology choices.

Gowri, Krishnan

2012-11-01T23:59:59.000Z

351

DOE standard: Integration of environment, safety, and health into facility disposition activities. Volume 1: Technical standard  

Science Conference Proceedings (OSTI)

This Department of Energy (DOE) technical standard (referred to as the Standard) provides guidance for integrating and enhancing worker, public, and environmental protection during facility disposition activities. It provides environment, safety, and health (ES and H) guidance to supplement the project management requirements and associated guidelines contained within DOE O 430.1A, Life-Cycle Asset Management (LCAM), and amplified within the corresponding implementation guides. In addition, the Standard is designed to support an Integrated Safety Management System (ISMS), consistent with the guiding principles and core functions contained in DOE P 450.4, Safety Management System Policy, and discussed in DOE G 450.4-1, Integrated Safety Management System Guide. The ISMS guiding principles represent the fundamental policies that guide the safe accomplishment of work and include: (1) line management responsibility for safety; (2) clear roles and responsibilities; (3) competence commensurate with responsibilities; (4) balanced priorities; (5) identification of safety standards and requirements; (6) hazard controls tailored to work being performed; and (7) operations authorization. This Standard specifically addresses the implementation of the above ISMS principles four through seven, as applied to facility disposition activities.

NONE

1998-05-01T23:59:59.000Z

352

Hunting for the Treasure at the End of theRainbow: Standardizing corporate IT Infrastructure  

Science Conference Proceedings (OSTI)

This paper tells the story of the definition and implementation of a corporate information infrastructure standard within Norsk Hydro. Standards are widely considered as the most basic features of information infrastructures public as well ... Keywords: actor network theory, global information systems, information infrastructure, standardization

Ole Hanseth; Kristin Braa

2001-12-01T23:59:59.000Z

353

Westinghouse Hanford Company (WHC) standards/requirements identification document (S/RID)  

Science Conference Proceedings (OSTI)

This Standards/Requirements Identification Document (S/RID) set forth the Environmental Safety and Health (ES&H) standards/requirements for Westinghouse Hanford Company Level Programs, where implementation and compliance is the responsibility of these organizations. These standards/requirements are adequate to ensure the protection of the health and safety of workers, the public, and the environment.

Bennett, G.L.

1996-03-15T23:59:59.000Z

354

Symmetric extension for lifted filter banks and obstructions to reversible implementation  

Science Conference Proceedings (OSTI)

Symmetric pre-extension is a standard approach to boundary handling for finite-length input vectors with linear phase filter banks. It works with both conventional linear implementations and the so-called reversible, or integer-to-integer, implementations ... Keywords: Filter bank, JPEG 2000, Lifting, Reversible, Symmetric extension

Brendt Wohlberg; Christopher M. Brislawn

2008-01-01T23:59:59.000Z

355

Implementing controlled languages in GF  

Science Conference Proceedings (OSTI)

This paper introduces GF, Grammatical Framework, as a tool for implementing controlled languages. GF provides a high-level grammar formalism and a resource grammar library that make it easy to write grammars that cover similar fragments in several natural ...

Krasimir Angelov; Aarne Ranta

2009-06-01T23:59:59.000Z

356

Oracle Essbase 9 Implementation Guide  

Science Conference Proceedings (OSTI)

Develop high-performance multidimensional analytic OLAP solutions with Oracle Essbase Build multidimensional Essbase database cubes and develop analytical Essbase applicationsStep-by-step instructions with expert tips from installation to implementationCan ...

Joseph Sydney Gomez; Sarma Anantapantula

2009-06-01T23:59:59.000Z

357

Migrating Interface Implementation to Aspects  

Science Conference Proceedings (OSTI)

Separation of concerns and modularization are the cornerstones of software engineering. However, when a system is decomposed into units, functionalities often emerge which cannot be assigned to a single element of the decomposition. The implementation ...

Paolo Tonella; Mariano Ceccato

2004-09-01T23:59:59.000Z

358

ARM - Expectations for Campaign Implementation  

NLE Websites -- All DOE Office Websites (Extended Search)

govField CampaignsExpectations for Campaign Implementation Schedule and Availability Preproposals now open for AMF and AAF Preproposals due 01 Feb Invited full proposals due 01 May...

359

An Emulated Digital CNN Implementation  

Science Conference Proceedings (OSTI)

A new emulated digital CNN Universal Machine chip architecture is introduced and the main steps of the design process are shown in this paper. One core processor can be implemented on 2 2 mm^2 silicon ...

Pter Keresztes; kos Zarndy; Tams Roska; Pter Szolgay; Tams Bezk; Timt Hidvgi; Pter Jns; Attila Katona

1999-11-01T23:59:59.000Z

360

Beyond the Standard Model  

NLE Websites -- All DOE Office Websites (Extended Search)

allá del Modelo Standard allá del Modelo Standard Avanzar Volver Principal ESTOY PERDIDO!!! El modelo standard explica muchas de las preguntas acerca de la estructura y la estabilidad de la materia, con sus seis tipos de quarks, sus seis tipos de leptones, y sus cuatro fuerzas fundamentales. Sin embargo, el modelo standard es una teoría incompleta porque todavía no puede explicar la naturaleza del mundo en forma completa. ¿Por qué hay tres generaciones de quarks y leptones? ¿Los quarks y leptones son realmente fundamentales, o están constituidos a su vez por partículas aún más fundamentales? ¿Por qué no puede el modelo standard predecir la masa de una partícula? De acuerdo con nuestros experimentos, las cantidades de materia y antimateria en el universo deberían ser iguales; pero, ¿por qué hemos

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

IEC 61850 Implementation and Transition  

Science Conference Proceedings (OSTI)

This IEC 61850 Implementation and Transition survey report summarizes results of an EPRI survey designed to understand adoption and usage of IEC 61850 within utilities as of 2011. Implementing IEC 61850 within a utility is not necessarily easy or straightforward. While transitioning electromechanical relays to microprocessors is a relatively straightforward process, taking advantage of the entire suite of benefits enabled by IEC-61850-enabled devices is another matter altogether. Utilities have to consid...

2011-12-06T23:59:59.000Z

362

Enterprise Service Bus Implementation Profile  

Science Conference Proceedings (OSTI)

The purpose of this report is to define an implementation profile for International Electrotechnical Commission (IEC) 61968 using technologies commonly found on an Enterprise Service Bus (ESB). More specifically, this document describes how message payloads defined by parts 3 through 9 of IEC 61968 are conveyed using Web Services and the Java Message Service (JMS). The goal is to provide details that are sufficient to enable implementations of IEC 61968 to be interoperable.

2009-04-30T23:59:59.000Z

363

FCT Safety, Codes and Standards: DOE Safety, Codes, and Standards...  

NLE Websites -- All DOE Office Websites (Extended Search)

Safety, Codes, and Standards Activities to someone by E-mail Share FCT Safety, Codes and Standards: DOE Safety, Codes, and Standards Activities on Facebook Tweet about FCT Safety,...

364

Converting DOE Technical Standards to Voluntary Consensus Standards...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE-TSPP-8-2013 DOE TECHNICAL STANDARDS September 2013 PROGRAM PROCEDURES CONVERTING DOE TECHNICAL STANDARDS TO VOLUNTARY CONSENSUS STANDARDS U.S. Department of Energy Office of...

365

Standards Actions, October 1999  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

projects were recently ini- projects were recently ini- tiated. If you have any questions or are interested in participating in the development of these standards, please contact the per- sons listed below. • Work Smart Standards Users Handbook, Project Number MGMT-0002; Maggie Sturdivant, EH-31; 301-903-0077, FAX 301- 903-0557, Maggie.Sturdivant @eh.doe.gov. • Criteria for Preparing and Pack- aging Plutonium Metals and Oxides for Long-term Storage, Project Number PACK-0013 (re- vision of DOE-STD-3013-96); Ray Cooperstein, 301-903- 5353, 301-903-7065, Raymond .Cooperstein@dp.doe.gov. • Industrial Hygiene Functional Area Qualifications, Project Number TRNG-0012; M. Norman Schwartz, EH-31; 301- 903-2996, FAX 301-903-4594, Norm.Schwartz@eh.doe.gov. DOE Technical Standards Recently Sent for Coordination

366

Site Lead TQP Standard  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Qualification Standard for the Qualification Standard for the Office of Safety and Emergency Management Evaluations Site Lead Program May 2011 Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy 1 Qualification Standard for the Office of Safety and Emergency Management Evaluations Site Lead Program A Site Lead is an individual, normally at a senior General Schedule (GS) level or Excepted Service, who is assigned the responsibility to assess and evaluate management systems, safety and health programs, and technical activities associated with U.S. Department of Energy (DOE) nuclear and non-nuclear facilities. Typically, a Site Lead has previously qualified as a Nuclear Safety Specialist or a Senior Technical Safety Manager. For exceptionally qualified individuals,

367

Standards Actions - May 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Project Canceled Project Canceled The following DOE Technical Standards project was recently canceled. If you have any questions about this action, please contact the person listed below. • Equipment Qualification Program for DOE-Owned Nuclear Facilities and Operations, Project Number FACR-0012; Samuel Rosenbloom, EH-31; 301-903-5749, Fax 301-903- 8693, Samuel.Rosenbloom@eh.doe.gov. The need for this document no longer ex- ists. DOE Technical Standards Recently Published The following DOE Technical Standard has recently been published: • DOE-STD-1063-2000, Facility Representatives, March 2000. This document updates and supersedes DOE-STD-1063-97, October 1997. DOE employees and DOE contractors may obtain copies from the ES&H Technical Infor- mation Services, U.S. Department of Energy; 1-800-473-4375, Fax 301-903-9823.

368

August 1999 Standards Actions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

this document is available on the this document is available on the Technical Standards Program (TSP) Internet Site at the URL shown at the bottom of this page. If you wish to comment on this document, please notify your TSM. * Design Criteria Standard for Electronic Records Manage- ment Software, Project Number INFT-0001; Carol Blackston, MA-42; 301-903-4294, FAX 301- 903-4101; Carol.Blackston @hq.doe.gov. Comments are due August 30, 1999. This stan- dard was adapted from the De- partment of Defense standard 5015.2 and tailored for specific DOE use. DOE Documents Recently Published The following DOE document has recently been published: * DOE-HDBK-3027-99, Integrated Safety Management Systems (ISMS) Verification - Team Leader's Handbook, June 1999. DOE employees and DOE contractors may obtain copies from the

369

Standard Report Templates  

NLE Websites -- All DOE Office Websites (Extended Search)

ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü Metrics Included in Every Report "How To" Series Standard Report Templates EPA's Portfolio Manager offers you eight standard reports with key metrics and information you can use to easily assess your portfolio's performance and progress, and thereby make informed business decisions. This document lists the metrics included in each of the eight reports so you can see what each report offers. Standard Reports Performance Highlights Energy Performance Emissions Performance Water Performance Fuel Performance ENERGY STAR Certification Status

370

Standard Review Plan Overview  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technical Framework for EM Projects Critical Decision (CD) Technical Framework for EM Projects Critical Decision (CD) Milestones Review & Approval Standard Review Plan (SRP) E n v i r o n m e n t a l M a n a g e m e n t DOE - EM - SRP - 2010 2nd Edition Overview March 2010 This page intentionally left blank. Standard Review Plan, 2 nd Edition, March 2010 1 Standard Review Plan Overview Technical Framework for EM Projects Critical Decision Milestones Review and Approval The Office of Environmental Management (EM) is responsible for managing the design, construction, operation, and eventual disposition of mission-critical projects/facilities. Coupled with this ongoing mission is the added responsibility for EM to diligently leverage and apply American Recovery and Reinvestment Act (ARRA) funds to accelerate the completion of its

371

Standards Actions - January 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Projects Initiated Projects Initiated The following DOE Technical Standards projects were recently initiated. If you have any questions or are interested in participating in the development of these stan- dards, please contact the per- sons listed below. • Establishing and Maintaining a Facility Representative Pro- gram at DOE Facilities , Project Number MGMT-0003 (revision of DOE-STD-1063-97); David Compton, S-3.1, 202-586-1034, Fax 202-586-3472, David .Compton@hq.doe.gov. • Nuclear Explosive Safety Study Process, Project Number SAFT- 0074 (Revision of DOE-STD- 3015-97); Helmut Filacchione, DP-21, 301-903-7519, Fax 301- 903-8628, Helmut.Filacchione @hq.doe.gov. DOE Technical Standards Project Canceled The following DOE Technical Standards project was recently can- celed. If you have any questions about this action, please contact

372

ORISE: Work Smart Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Work Smart Standards Work Smart Standards ORISE Work Smart Standards Set for Environment, Safety, and Health Revision #1, March 21, 2000 Revision #2, Sept. 29, 2000 Revision #3, June 28, 2001 Revision #4, Nov. 9, 2001 Revision #5, Nov. 30, 2001 Revision #6, Jan. 31, 2002 Revision #7, June 28, 2002 Revision #8, Oct. 17, 2002 Revision #9, Nov. 21, 2002 Revision #10, Feb. 28, 2003 Revision #11, May 23, 2003 Revision #12, May 30, 2003 Revision #13, Oct. 30, 2003 Revision #14, Jan. 21, 2004 Revision #15, May 24, 2004 Revision #16, Aug. 17, 2004 Revision #17, Aug. 27, 2004 Revision #18, Oct. 14, 2004 Revision #19, March 28, 2005 Revision #20, May 31, 2005 Revision #21, Aug. 24, 2005 Revision #22, Feb. 17, 2006 Revision #23, March 22, 2006 Revision #24, May 19, 2006 Revision #25, July 26, 2006 Revision #26, Nov. 28, 2006

373

CID Standard Reports  

Office of Environmental Management (EM)

CID Reports > Standard CID Reports > Standard Reports Central Internet Database CID Photo Banner Standard Reports Radioactive Waste WIMS-1: WASTE STREAM DISPOSITION FORECAST REPORT Adobe PDF Document Detailed waste stream disposition report by reporting site and disposition site that provides forecasted waste disposition volumes. Go directly to WIMS Exit CID Website to generate custom reports. Although WIMS Exit CID Website is a public site you will need to register and provide contact information the first time you enter WIMS Exit CID Website . Contaminated Groundwater GW-1: CONTAMINATED GROUNDWATER REPORTS A link to the DOE Groundwater Database web site. This site provides detailed information about groundwater plumes at DOE sites. Information includes contaminants, hydrogeology, and cleanup technologies.

374

Hydrogen Purity Standard  

NLE Websites -- All DOE Office Websites (Extended Search)

Compressed Gas Association Compressed Gas Association Roger A. Smith Technical Director April 26, 2004 Hydrogen Purity Standard Compressed Gas Association 2 Compressed Gas Association ‹ 150 Members „ Industrial Gas Companies „ Equipment Manufacturers „ Other Gas Industry Associations „ Other SDOs ‹ Manufacturers, Fillers, Distributors, and Transporters of Industrial and Medical Gases Compressed Gas Association 3 Hydrogen Activities ‹ Committees „ Hydrogen Fuel Technology „ Bulk Distribution Equipment „ Hazardous Materials Codes „ Gas Specifications „ Cylinders, Valves & PRD's ‹ International „ Europe (EIGA) „ Japan (JIGA) „ Asia (AIGA) „ United Nations Compressed Gas Association 4 Hydrogen Purity Standard ‹ Draft hydrogen purity standard for stationary fuel cells and ICE's in 10 months

375

Standard Model Holdout INSIDE  

NLE Websites -- All DOE Office Websites (Extended Search)

May 2, 1997 May 2, 1997 Number 9 f Searching for the Standard Model Holdout INSIDE 2 University Close-Up: Pisa 5 Facilities Managers' Meeting 6 Birth of a Bison Photo by Reidar Hahn An international collaboration at Fermilab sets out to observe the elusive tau neutrino. by Donald Sena, Office of Public Affairs When two collaborations announced the discovery of the top quark at Fermi National Accelerator Laboratory in 1995, many news outlets erroneously reported that the last remaining piece of the current theory of matter and energy, known as the Standard Model, had been found. What reporters and even a few physicists forgot is that the elusive tau neutrino, while firmly entrenched in the Standard Model, has never been directly observed. In the early 1980s, there was one minor attempt to find the tau neutrino

376

Department of Energy Standards Index  

Science Conference Proceedings (OSTI)

This TSL, intended for use in selecting and using DOE technical standards and other Government and non-Government standards, provides listing of current and inactive DOE technical standards, non-Government standards adopted by DOE, other Government documents in which DOE has a recorded interest, and cancelled DOE technical standards.

NONE

1995-08-01T23:59:59.000Z

377

Standards for ICCP API  

Science Conference Proceedings (OSTI)

This report reflects an update to the original 12/99 EPRI Report TE-114613 and the current status of the standard as of 6/30/00. The Inter-Control Center Communication Protocol (ICCP) was developed as an EPRI project for the exchange of power system information between control centers, or between a control center and a generation control system or substation. ICCP is now an international standard IEC 60870-6 known as Telecontrol Application Service Element 2 (TASE.2) (See Reference 1-3). However, the App...

2000-08-03T23:59:59.000Z

378

Curriculum Implementation: a Study of the Effect of a Specialized Curriculum on Sixth Grade Mathematics Summative Test Scores in a Rural Middle School.  

E-Print Network (OSTI)

??The purpose of this study was to examine curriculum implementation in sixth grade mathematics as it related to standardized testing in a rural district. The (more)

Bicknell, Libby Plath

2009-01-01T23:59:59.000Z

379

DOE technical standards list: Department of Energy standards index  

Science Conference Proceedings (OSTI)

This technical standards list (TSL) was prepared for use by personnel involved in the selection and use of US DOE technical standards and other government and non-government standards. This TSL provides listings of current DOE technical standards, non-government standards that have been adopted by DOE, other government documents in which DOE has a recorded interest, and cancelled DOE technical standards. Standards are indexed by type in the appendices to this document. Definitions of and general guidance for the use of standards are also provided.

NONE

1997-06-01T23:59:59.000Z

380

WHC natural phenomena hazards mitigation implementation plan  

SciTech Connect

Natural phenomena hazards (NPH) are unexpected acts of nature which pose a threat or danger to workers, the public or to the environment. Earthquakes, extreme winds (hurricane and tornado),snow, flooding, volcanic ashfall, and lightning strike are examples of NPH at Hanford. It is the policy of U.S. Department of Energy (DOE) to design, construct and operate DOE facilitiesso that workers, the public and the environment are protected from NPH and other hazards. During 1993 DOE, Richland Operations Office (RL) transmitted DOE Order 5480.28, ``Natural Phenomena Hazards Mitigation,`` to Westinghouse Hanford COmpany (WHC) for compliance. The Order includes rigorous new NPH criteria for the design of new DOE facilities as well as for the evaluation and upgrade of existing DOE facilities. In 1995 DOE issued Order 420.1, ``Facility Safety`` which contains the same NPH requirements and invokes the same applicable standards as Order 5480.28. It will supersede Order 5480.28 when an in-force date for Order 420.1 is established through contract revision. Activities will be planned and accomplished in four phases: Mobilization; Prioritization; Evaluation; and Upgrade. The basis for the graded approach is the designation of facilities/structures into one of five performance categories based upon safety function, mission and cost. This Implementation Plan develops the program for the Prioritization Phase, as well as an overall strategy for the implemention of DOE Order 5480.2B.

Conrads, T.J.

1996-09-11T23:59:59.000Z

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Technical Standards, 2004 Annual Report - July 29, 2004 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2004 Annual Report - July 29, 2004 2004 Annual Report - July 29, 2004 Technical Standards, 2004 Annual Report - July 29, 2004 July 29, 2004 Fiscal Year 2004, Annual Report to the Office of Management and Budget, Standards use and Participation The Department of Energy (DOE) implements the federal guidance and requirements of OMB Circular A-119 (OMB A-119) and the statutory requirements of Public Law (PL) 104-113 (15 USC 272) regarding the use of voluntary consensus standards (VCSs) through specific Departmental directives (policies, orders, requirements, guides, and technical standards) and supporting programs and management systems. Technical Standards, 2004 Annual Report More Documents & Publications Technical Standards, Office of Management and Budget Report for FY-2012 - December 19, 2012

382

Technical Standards, GENII- Gap Analsis - May 3, 2004 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technical Standards, GENII- Gap Analsis - May 3, 2004 Technical Standards, GENII- Gap Analsis - May 3, 2004 Technical Standards, GENII- Gap Analsis - May 3, 2004 May 3, 2004 Software Quality Assurance Improvement Plan: GENII Gap Analysis The GENII software, for radiological dispersion and consequence analysis, is one of the codes designated for the toolbox. To determine the actions needed to bring the GENII code into compliance with the SQA qualification criteria, and develop an estimate of the resources required to perform the upgrade, the Implementation Plan has committed to sponsoring a code-specific gap analysis document. Technical Standards, GENII- Gap Analsis More Documents & Publications Guidance on GENII computer code - July 6, 2004 Technical Standards, ALOHA-Gap Analysis - May 3, 2004 Technical Standards, MELCOR - Gap Analysis - May 3

383

DOE Technical Standards Program: Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Department of Energy Technical Standards Procedures Department of Energy Technical Standards Procedures Office of Nuclear Safety The following procedures should be used to write, revise, or maintain a DOE technical standard. They are also used to convert a DOE technical standard to a non-government standard or to form a topical committee. Table of Contents (TSPP-00) Program Overview and Responsibilities (TSPP-01) Initiating DOE Technical Standards (TSPP-02) Use of Voluntary Consensus Standards and Interaction with Standards Development Organizations (TSPP-03) Developing DOE Technical Standard (TSPP-04) Coordination of Technical Standards (TSPP-05) - Draft In Concurrence Resolution - TSPP-06-2009 is the currently approved TSPP that addresses coordination of DOE Technical Standards. Approving and Issuing DOE Technical Standards (TSPP-06)

384

Das Standard Modell  

NLE Websites -- All DOE Office Websites (Extended Search)

Model Model Was ist fundamental? Das Standard Modell Physiker haben eine Theorie - Das Standard Modell - entwickelt, welche erklärt, woraus die Welt besteht und was sie zusammenhält. Es ist eine einfache und überzeugende Theorie, welche hunderte von Teilchen und ihre gegenseitigen Wechselwirkungen erklärt. Dazu braucht sie nur wenige elementare Teilchen : 6 Quarks. 6 Leptonen. Das bekannteste Lepton ist das Elektron. Wir reden gleich von Leptonen. Kraft-Träger Teilchen, wie z.B. das Photon. Wir werden später über diese Teilchen reden. Alle bekannten materiellenTeilchen sind aus Quarks und Leptonen zusammengesetzt und sie wechselwirken untereinander durch den Austausch von Kraft-Träger Teilchen. Das Standard Modell ist eine gute Theorie. Eine grosse Zahl von Experimenten haben ihre Voraussagen mit unglaublicher Präzision bestätigt und alle Teilchen, welche die Theorie bis heute vorausgesagt hat, wurden auch gefunden. Aber die Theorie kann nicht alles erklären. Die Schwerkraft zum Beispiel ist nicht im Standard Modell eingeschlossen.

385

Standard Model Summary  

NLE Websites -- All DOE Office Websites (Extended Search)

del Modelo Standard del Modelo Standard Volver Principal ESTOY PERDIDO!!! Ahora que usted ha visto las distintas partes que forman la teoría del Modelo Standard, es el momento de una explicación más completa, sobre las partículas fundamentales y sus interacciones. Para resumir, los físicos creen que pueden explicar todos los tipos de materia observados utilizando seis tipos de quarks y seis tipos de leptones. Atribuyen todas las fuerzas observadas a cuatro fuerzas fundamentales, cada una de las cuales tiene asociada su partícula mediadora. El Modelo Standard también incluye la teoría cuántica de las interacciones fuertes (Quantum chromodynamics, o QCD), y la de las interacciones electro-débiles unificadas (débiles y electromagnéticas, QED). Todavía no se sabe cómo hacer una teoría cuántica de la

386

Laser Propulsion Standardization Issues  

SciTech Connect

It is a relevant issue in the research on laser propulsion that experimental results are treated seriously and that meaningful scientific comparison is possible between groups using different equipment and measurement techniques. However, critical aspects of experimental measurements are sparsely addressed in the literature. In addition, few studies so far have the benefit of independent confirmation by other laser propulsion groups. In this paper, we recommend several approaches towards standardization of published laser propulsion experiments. Such standards are particularly important for the measurement of laser ablation pulse energy, laser spot area, imparted impulse or thrust, and mass removal during ablation. Related examples are presented from experiences of an actual scientific cooperation between NU and DLR. On the basis of a given standardization, researchers may better understand and contribute their findings more clearly in the future, and compare those findings confidently with those already published in the laser propulsion literature. Relevant ISO standards are analyzed, and revised formats are recommended for application to laser propulsion studies.

Scharring, Stefan; Eckel, Hans-Albert [Institute of Technical Physics, German Aerospace Center (DLR), D-70569 Stuttgart, Pfaffenwaldring 38-40 (Germany); Roeser, Hans-Peter [Institute of Space Systems, University of Stuttgart, D-70569 Stuttgart, Pfaffenwaldring 31 (Germany); Sinko, John E. [Micro-Nano Global Center of Excellence, Nagoya University (Niue), Nagoya, Aichi, 464-8603 (Japan); Sasoh, Akihiro [Department of Aerospace Engineering, Nagoya University, Nagoya, Aichi, 464-8603 (Japan)

2010-10-08T23:59:59.000Z

387

Universal metadata standard  

Science Conference Proceedings (OSTI)

Consciousness is based on the association of notions or a neural network. Similarly, the creation of the next-generation Internet (semantic web) is impossible without attributes that allow the semantic association of documents and their integration into ... Keywords: association, classification, document, documentography, identification, metabase, metadata, metagraphy, standard

A. V. Poleev

2011-04-01T23:59:59.000Z

388

ARCHITECTURAL AND CIVIL STANDARDS  

SciTech Connect

Hanford Atomic Production Operation specification guides and standards for architectural and civil engineering are presented. Information includes construction of roads, railroads, roofs, signs, buildings, building equipment, sewers, fences, safety systems, and drainage systems. Details of this manual are given in TID-4100 (Suppl.). (N.W.R.)

1963-01-01T23:59:59.000Z

389

SAFETY-MECHANICAL STANDARDS  

SciTech Connect

Hanford Atomic Production Operation specification guides and standards for plumbing, chemical ngineering, mechanical engineering, sanitary engineering, exhaust systems, steam engineering, stainless steel, dry boxes, thermal insulation, filtration, and materials testing are presented. Details of this manual are given in TID-4100 (Suppl.). (N.W.R.)

1964-10-31T23:59:59.000Z

390

Extending WS-Security to Implement Security Protocols for Web Services  

E-Print Network (OSTI)

Web services use tokens provided by the WS-Security standard to implement security protocols. We propose several extensions to the WS-Security standard, including name types, key and random number extensions. The extensions are used to implement existing protocols such as ISO9798, Kerberos or BAN-Lowe. The advantages of using these implementations rather than the existing, binary ones, are inherited from the advantages of using Web service technologies, such as extensibility and end-to-end security across multiple environments that do not support a connection-based communication.

Bela, Genge

2009-01-01T23:59:59.000Z

391

Acquisitions of Products and Services for Implementation of HSPD-12  

NLE Websites -- All DOE Office Websites (Extended Search)

GSA Federal Supply Service GSA Federal Supply Service August 10, 2005 MEMORANDUM FOR CHIEF FINANCIAL OFFICERS CHIEF INFORMATION OFFICERS CHIEF ACQUISITION OFFICERS FROM: BARBARA L. SHELTON ACTING COMMISSIONER FEDERAL ACQUISITION SERVICE SUBJECT: Acquisitions of Products and Services for Implementation of HSPD-12 Homeland Security Presidential Directive-12 (HSPD-12), "Policy for a Common Identification Standard for Federal Employees and Contractors" requires agencies to use only information technology products and services that meet this standard. The Office of Management and Budget (OMB) has designated the

392

Federal Agency NEPA Implementing Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Agency NEPA Implementing Procedures Agency NEPA Implementing Procedures Note: Some Departments' agencies have their own NEPA implementing procedures. To access Department-wide NEPA implementing procedures, click on the name of the Federal Department. To access NEPA implementing procedures for Department's agencies, click on the provided links. Department/ Agency: Division: Link: Department of Agriculture Agricultural Research Service http://www.ecfr.gov/cgi- in/text- idx?c=ecfr&SID=47c103e07fd64e933c7f74c 4b3c4ac9a&rgn=div5&view=text&node=7:6. 1 2 1 8&id 7 Animal and Plant Health Inspection Service http://www.ecfr.gov/cgi-bin/text- idx?c=ecfr&SID=47c103e07fd64e933c7f74c 4b3c4ac9a&rgn=div5&view=text&node=7:5. 1.1.1.21&idno=7 Farm Service Agency http://www.ecfr.gov/cgi-bin/text-

393

Interconnection Standards | Open Energy Information  

Open Energy Info (EERE)

Interconnection Standards Interconnection Standards Jump to: navigation, search Interconnection standards govern the technical and procedural process by which an electric customer connects an electric-generating system to the grid. Interconnection standards specify the technical, contractual, metering, and rate rules that system owners and utilities must abide by. Standards for systems interconnected at the distribution level are typically adopted by state public utility commissions, while the Federal Energy Regulatory Commission (FERC) has adopted standards for systems interconnected at the transmission level. Not all states have adopted interconnection standards, and some states’ standards apply only to investor-owned utilities – not to municipal utilities and electric cooperatives. [1]

394

DOE Technical Standards Program: Overview  

NLE Websites -- All DOE Office Websites (Extended Search)

Office of Nuclear Safety Vision The culture of the DOE community will be based on standards. Technical standards will formally integrate part of all DOE facility, program and...

395

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

energy and water savings for urinals during any future standard rulemaking. The Standards and Test Procedures for this product are related to Rulemaking for Plumbing Products...

396

NIST Standard Reference Simulation Website  

Science Conference Proceedings (OSTI)

... simulations, that can be treated similar to "standard reference data ... techniques and compiled by NIST under the Standards Reference Data Program. ...

2013-08-27T23:59:59.000Z

397

ANSI/NIST-ITL Standard  

Science Conference Proceedings (OSTI)

ANSI/NIST-ITL STANDARD HOMEPAGE. The 2013 Update to the ANSI/NIST-ITL standard is now being voted upon !. It is available here. ...

2013-09-17T23:59:59.000Z

398

Biomagnetic Imaging Standards and Microsystems  

Science Conference Proceedings (OSTI)

... Resonance in Medicine (ISMRM), EEEL is developing a standard "phantom" for ... by EEEL and the ISMRM. Committee on Standards for Quantitative. ...

2013-05-13T23:59:59.000Z

399

DOE Technical Standards Program: Archive  

NLE Websites -- All DOE Office Websites (Extended Search)

Department of Energy Technical Standards Archives Office of Nuclear Safety Number Title Status TSPP-00 Technical Standards Program Topical Committees (TSPP-00) PDF TSPP-00 TSPP-01...

400

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Conservation Standard Sign up for e-mail updates on regulations for this and other products The Department of Energy (DOE) is has established energy conservation standards...

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Appliance and Equipment Efficiency Standards  

Energy.gov (U.S. Department of Energy (DOE))

'' Note: The federal government has imposed and updated appliance efficiency standards through several legislative acts,* and now has standards in place or under development for 30 classes of...

402

NREL: Photovoltaics Research - Standards Development  

NLE Websites -- All DOE Office Websites (Extended Search)

NREL's Photovoltaic (PV) Engineering group supports the development of national and international standards for PV engineering. Current standards lack specifics on how to...

403

AEDG Implementation Recommendations: Floors | Building Energy Codes Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Floors Floors The Advanced Energy Design Guide (AEDG) for Small Office Buildings, 30% series, seeks to achieve 30% savings over ASHRAE Standard 90.1-1999. This guide focuses on improvements to small office buildings, less than 20,000ft2. The recommendations in this article are adapted from the implementation section of the guide and focus on mass floors; steel joist or wood frame floors; slab-on-grade floors. Publication Date: Wednesday, May 13, 2009 air_floors.pdf Document Details Affiliation: DOE BECP Focus: Compliance Building Type: Commercial Code Referenced: ASHRAE Standard 90.1-1999 Document type: AEDG Implementation Recommendations Target Audience: Architect/Designer Builder Contractor Engineer State: All States Contacts Web Site Policies U.S. Department of Energy

404

Launch implementation | Open Energy Information  

Open Energy Info (EERE)

Launch implementation Launch implementation Jump to: navigation, search Stage 4 LEDS Home Introduction to Framework Assess current country plans, policies, practices, and capacities Develop_BAU Stage 4: Prioritizing and Planning for Actions Begin execution of implementation plans 1.0. Organizing the LEDS Process 1.1. Institutional Structure for LEDS 1.2. Workplan to Develop the LEDS 1.3. Roles and responsibilities to develop LEDS 2.1. Assess current country plans, policies, practices, and capacities 2.2. Compile lessons learned and good practices from ongoing and previous sustainable development efforts in the country 2.3. Assess public and private sector capacity to support initiatives 2.4. Assess and improve the national GHG inventory and other economic and resource data as needed for LEDS development

405

Implementation Trafton et al. Implementation Science 2010, 5:26  

E-Print Network (OSTI)

previously [25]. This study was approved and overseen by the Stanford University Human Research Protection and Implement Decision Support Systems' from the VA Health Service Research and Develop- ment (HSR&D) Program://www.implementationscience.com/content/5/1/26 Open AccessRESEARCH ARTICLE BioMed Central © 2010 Trafton et al; licensee BioMed Central Ltd

Peleg, Mor

406

Implementation Standing Technical Committee Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Implementation Standing Technical Committee (I-STC) Meeting Deane Evans (NJIT) and Stacy Hunt (Confluence), co-chairs March 1, 2012 What is the I-STC? * Focused on identifying and documenting key barriers and opportunities in implementation of Building America (BA) research results How Does the I-STC Work? * Fosters discussion and prioritization of key research activities * Documents these for DOE/NREL planning purposes 2012 Focus * Clarify key priorities and ensure proper prioritization * Research and track activities that address these priorities inside and outside of BA * Try to knock some of these priorities off the list by documenting existing solutions * Identify critical tasks for 2013 and beyond

407

Conservation Standards Enforcement | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

November 20, 2012 November 20, 2012 Teddico: Noncompliance Determination (2012-SE-5409) DOE issued a Notice of Noncompliance Determination to The Electrical Design, Development and Implementation Company d/b/a Teddico finding that a variety of basic models of magnetic probe-start metal halide lamp fixtures do not comport with the energy conservation standards. November 19, 2012 Hydac: Noncompliance Determination (2012-SE-4107) DOE issued a Notice of Noncompliance Determination to Hydac Technology Corporation finding that a variety of electric motor basic models do not comport with the energy conservation standards. November 7, 2012 YMGI: Order (2011-SCE-1605) DOE ordered YMGI Group LLC to pay a $31,400 civil penalty after finding (1) YMGI had failed to certify that certain models of residential central air

408

Nuclear Criticality Safety Requirements Implementation Matrix for Tank Farms  

SciTech Connect

This document provides a detailed matrix of specific Tank Farms nuclear criticality safety program elements indexed to primary requirements documents. These requirements are collected at a higher level in HNF-SO-MP-SRID-001, ''Tank Waste Remediation System Standards/Requirements Identification Document.'' The intended use of this document is to provide a roadmap for implementing procedures and assessments.

WEISS, E.V.

2000-05-17T23:59:59.000Z

409

CA/CPS: A Communications ZEBRA implementation using CPS  

Science Conference Proceedings (OSTI)

CZ/CPS is an implementation of the Communications ZEBRA distributed computing environment utilizing the CPS communications protocol. CZ/CPS is intended for parallelization of high energy physics application programs using the CERN Program Library memory and data structure management features. CZ/CPS provides transparent communication of ZEBRA data structures among cooperative processes using standard interfaces for ZEBRA I/O. Examples of usage in a CPS HBOOK4 and GEANT3 application are provided.

Roberts, L.A.

1991-05-01T23:59:59.000Z

410

The Standard Model  

NLE Websites -- All DOE Office Websites (Extended Search)

Avanzar Volver Principal ESTOY PERDIDO!!! Avanzar Volver Principal ESTOY PERDIDO!!! Los físicos han desarrollado una teoría llamada el Modelo Standard, que intenta describir toda la materia y todas las fuerzas existentes en el universo (excepto la gravedad). Su elegancia radica en la capacidad de justificar la existencia de cientos de partículas e interacciones complejas, sobre la base de sólo unas pocas partículas e interacciones fundamentales. Partículas portadoras de fuerza: Cada tipo de fuerza fundamental es "transportada" por una partícula portadora de fuerza (el fotón es un ejemplo). Partículas materiales: El Modelo Standard establece que la mayoría de las partículas de las cuales tenemos conocimiento están compuestas en realidad de partículas más fundamentales llamadas quarks. Hay otra clase

411

Standards Actions, April 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Canceled Canceled The following DOE Technical Standards projects were recently canceled. If you have any questions about this action, please contact the persons listed below. • Accelerated Learning - A Systematic Approach, Project Number 6910-0061; Eula Baldwin, EH-31; 208-526-9472, egb@inel.gov. The need for this document no longer exists. • Environmental Safety and Health Configuration Guide, Project Number FACR-0013; Chan- dra S. Majumdar, EM-23; 301-903-7904, Fax 301-903-4423, Chandra.Majumdar @em.doe.gov. The need for a DOE Technical Standard on this matter no longer exists. • Occupational Safety and Health Handbook, Project Number HFAC-0011; Terry Krietz, EH-51; 301-903-6456, Fax 301-903-2239, Terry.Krietz@hq.doe.gov. The need for this document no longer exists.

412

Active DOE Technical Standards  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Active DOE Technical Standards Active DOE Technical Standards Document Number Document Title Responsible SLM DOE-HDBK-1001-96 DOE-HDBK-1002-96 DOE-HDBK-1003-96 DOE-HDBK-1010-92 DOE-HDBK-1011/1-92 DOE-HDBK-1011/2-92 DOE-HDBK-1011/3-92 DOE-HDBK-1011/4-92 DOE-HDBK-1012/1-92 DOE-HDBK-1012/2-92 DOE-HDBK-1012/3-92 DOE-HDBK-1013/1-92 DOE-HDBK-1013/2-92 DOE-HDBK-1014/1-92 DOE-HDBK-1014/2-92 DOE-HDBK-1015/1-93

413

Standards Actions - February 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Initiated Initiated The following DOE Technical Standards projects were recently initiated. If you have any questions or are interested in participating in the development of these stan- dards, please contact the persons listed below. Complete listings of all DOE Technical Stan- dards projects and their status are given in the Web Site referenced at the bottom of this page. To access these lists from the home page, click on “DOE Technical Standards,” then click on “Projects” in the left-hand frame to show the links to the project lists. • Preparation Guide for U.S. Department of Energy Non-Reactor Nuclear Facility Safety Analysis Reports, Project Number SAFT-0075 (5-year review/update of DOE-STD-3009-94); Richard W. Englehart, EH-31, 301-903-3718, Fax 301-903-1182, Richard.Englehart@hq.doe.gov. This

414

Standardized radiological dose evaluations  

SciTech Connect

Following the end of the Cold War, the mission of Rocky Flats Environmental Technology Site changed from production of nuclear weapons to cleanup. Authorization baseis documents for the facilities, primarily the Final Safety Analysis Reports, are being replaced with new ones in which accident scenarios are sorted into coarse bins of consequence and frequency, similar to the approach of DOE-STD-3011-94. Because this binning does not require high precision, a standardized approach for radiological dose evaluations is taken for all the facilities at the site. This is done through a standard calculation ``template`` for use by all safety analysts preparing the new documents. This report describes this template and its use.

Peterson, V.L.; Stahlnecker, E.

1996-05-01T23:59:59.000Z

415

Universe Adventure Web Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Universe Universe Adventure Web Standards for the Smart Physics Student Author: Patrick Lii - plii@ugastro.berkeley.edu Date: August 3, 2007 ABSTRACT You may be wondering: why are the Universe Adventure web standards so impor- tant? And why do I have to read this stupid document about them? The old versions of our site were plagued with messy (and faulty) coding: the pages were littered with broken links, missing images, broken flash files, and all sorts of other problems which made the site highly inaccessible. When we tried to fix these errors, we found that the coding was so incredibly messy that a simple edit like changing some of the words in a paragraph or adding an image took hours rather than minutes. In fact, the coding was so horrific that we simply constructed an entirely new site rather than making the laborious attempt to fix the old one. In order to make sure that future students working

416

TECHNIQUE, REFERENCE STANDARD, EQUIPMENT  

E-Print Network (OSTI)

has met the requirements of the IAS Accreditation Criteria for Calibration Laboratories (AC204), has demonstrated compliance with the ANS/ISO/IEC Standard 17025:2005, General requirements for the competence of testing and calibration laboratories, and has been accredited commencing July 10, 2012, for the calibration discipline(s) listed in the approved scope of accreditation. The laboratory meets IAS program requirements in the field of calibration.

Teknik Malzeme; Is Merkezi; Yenisehir Izmir; Patrick V. Mccullen; C. P. Ramani; Teknik Malzeme Merkezi; M Meatest; Multifunction Calibrator

2012-01-01T23:59:59.000Z

417

Standard interface file handbook  

SciTech Connect

This handbook documents many of the standard interface file formats that have been adopted by the US Department of Energy to facilitate communications between and portability of, various large reactor physics and radiation transport software packages. The emphasis is on those files needed for use of the VENTURE/PC diffusion-depletion code system. File structures, contents and some practical advice on use of the various files are provided.

Shapiro, A.; Huria, H.C. (Cincinnati Univ., OH (United States))

1992-10-01T23:59:59.000Z

418

STANDARD SOLAR NEUTRINOS  

E-Print Network (OSTI)

The predictions of an improved standard solar model are compared with the observations of the four solar neutrino experiments. The improved model includes premain sequence evolution, element diffusion, partial ionization effects, and all the possible nuclear reactions between the main elements. It uses updated values for the initial solar element abundances, the solar age, the solar luminosity, the nuclear reaction rates and the radiative opacities. Neither nuclear equilibrium, nor complete ionization are assumed. The calculated 8 B solar neutrino flux is consistent, within the theoretical and experimental uncertainties, with the solar neutrino flux measured by Kamiokande. The results from the 37 Cl and 71 Ga radiochemical experiments seem to suggest that the terrestrial 7 Be solar neutrino flux is much smaller than that predicted. However, the present terrestrial defecit of 7 Be solar neutrinos may be due to the use of inaccurate theoretical neutrino absorption cross sections near threshold for extracting solar neutrino fluxes from production rates. Conclusive evidence for a real deficit of 7 Be solar neutrinos will require experiments such as BOREXINO or HELLAZ. A real defecit of 7 Be solar neutrinos can be due to either astrophysical reasons or neutrino properties beyond the standard electroweak model. Only future neutrino experiments, such as SNO, Superkamiokande, BOREXINO and HELLAZ, will be able to provide conclusive evidence that the solar neutrino problem is a consequence of neutrino properties beyond the standard electroweak model. Earlier indications may be provided by long baseline neutrino oscillation experiments. 1

Arnon Dar

2008-01-01T23:59:59.000Z

419

Federal Energy Management Program: Plans, Implementation, and...  

NLE Websites -- All DOE Office Websites (Extended Search)

Plans, Implementation, and Results to someone by E-mail Share Federal Energy Management Program: Plans, Implementation, and Results on Facebook Tweet about Federal Energy...

420

Solar Schools Assessment and Implementation Project: Financing...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Solar Schools Assessment and Implementation Project: Financing Options on Solar Installations on K-12 Schools Solar Schools Assessment and Implementation Project: Financing Options...

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

IMPLEMENTATION OF INTEGRATED BUSINESS INFORMATION SYSTEMS WITHIN...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

IMPLEMENTATION OF INTEGRATED BUSINESS INFORMATION SYSTEMS WITHIN THE DEPARTMENT OF ENERGY, DOEIG-0466 IMPLEMENTATION OF INTEGRATED BUSINESS INFORMATION SYSTEMS WITHIN THE...

422

Blackout 2003: Blackout Final Implementation Report | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Blackout Final Implementation Report Blackout 2003: Blackout Final Implementation Report Final Report on the August 14, 2003 Blackout in the United States and Canada: Causes and...

423

Standards for CLINICAL RESEARCH WITHIN THE NIH INTRAMURAL  

E-Print Network (OSTI)

The Standards for Clinical Research set forth some essential principles and processes for the conduct of clinical research in the intramural research programs of the National Institutes of Health. To achieve patient safety, efficient protocol implementation, and effective quality assurance and improvement requires adequate training of clinical investigators and sufficient infrastructure to support their endeavors. Consequently, the Standards should assist both new and experienced investigators as they apply good clinical practice in their research to achieve high-quality results. The Standards were developed in January 2000 by the Clinical Center Medical Executive Committee, on which all the NIH institutes are represented by their clinical directors. They were endorsed by the scientific directors

unknown authors

2009-01-01T23:59:59.000Z

424

Hospital laundry standards and energy conservation: a program plan  

SciTech Connect

A program plan describing required research and experimental plans for establishing a proposed revision of hospital laundry standards is presented. An extension of the literature search done by Hittman and Associates was done to see whether the quality of the finished laundry could be maintained under revised standards. Consideration was given to stain removal, whiteness, and sanitation. An extensive review of published literature on standards is included. There is room for energy conservation measures in the hospital laundry, but it is noted that energy conservation measures must be accompanied by care and practicality in their implementation.

Battles, D.R.; Vesley, D.; Banks, R.S.

1980-01-01T23:59:59.000Z

425

New No-Cost ANTFARM Tool Maps Control System Networks to Help Implement  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

New No-Cost ANTFARM Tool Maps Control System Networks to Help New No-Cost ANTFARM Tool Maps Control System Networks to Help Implement Cyber Security Standards New No-Cost ANTFARM Tool Maps Control System Networks to Help Implement Cyber Security Standards Funded under the Department of Energy's National SCADA Test Bed Program, Sandia National Laboratories recently released a new software tool that will aid energy utility owners in mapping and visualizing their control system networks-a critical first step in meeting the North American Electric Reliability Corporation's Critical Infrastructure Protection (NERC CIP) standards. New No-Cost ANTFARM Tool Maps Control System Networks to Help Implement Cyber Security Standards More Documents & Publications Advanced Network Toolkit for Assessments and Remote Mapping (ANTFARM)

426

1994 Building energy codes and standards workshops: Summary and documentation  

SciTech Connect

During the spring of 1994, Pacific Northwest Laboratory (PNL), on behalf of the U.S. Department of Energy (DOE) Office of Codes and Standards, conducted five two-day Regional Building Energy Codes and Standards workshops across the United States. Workshops were held in Chicago, Philadelphia, Atlanta, Dallas, and Denver. The workshops were designed to benefit state-level officials including staff of building code commissions, energy offices, public utility commissions, and others involved with adopting/updating, implementing, and enforcing state building codes in their states. The workshops provided an opportunity for state and other officials to learn more about the Energy Policy Act of 1992 (EPAct) requirements for residential and commercial building energy codes, the Climate Change Action Plan, the role of the U.S. Department of Energy and the Building Energy Standards Program at Pacific Northwest Laboratory, the commercial and residential codes and standards, the Home Energy Rating Systems (HERS), Energy Efficient Mortgages (EEM), training issues, and other topics related to the development, adoption, implementation, and enforcement of building energy codes. In addition to receiving information on the above topics, workshop participants were also encouraged to inform DOE of their needs, particularly with regard to implementing building energy codes, enhancing current implementation efforts, and building on training efforts already in place. This paper documents the workshop findings and workshop planning and follow-up processes.

Sandahl, L.J.; Shankle, D.L.

1994-09-01T23:59:59.000Z

427

Police Body Armor Standards and Testing,  

E-Print Network (OSTI)

For two decades, the number of police officers shot to death each year has been declining while the number of officers shot has been increasing. The decrease in the lethality of shootings is partly attributable to the increase in wearing of bullet-resistant body armor, especially soft, inconspicuous armor designed to be worn full-time. A prospective purchaser can see how much of the body an armor garment covers but cannot see whether it will stop a particular kind of bullet at a particular velocity and protect the wearer from the impact. To provide benchmarks for protection, the National Institute of Justice issued NIJ Standard 0101.03 in 1987. It specifies standard procedures for testing samples of armor. If samples of a model pass, the NIJ or the manufacturer may certify that the model has the type of ballistic resistance for which it was tested. The standard has been controversial since it was issued. This Report describes the origin of the standard, the rationale for particular provisions, and the main points of controversy, which concern acceptable risks, the validity and discrumination of the test, and the reproducibility of results. OTA finds that resolving these controversies will require specifying acceptable risks quantitatively, performing additional research to test validity, and implementing

Vol I

1992-01-01T23:59:59.000Z

428

SCIENCE AND IMPLEMENTATION PLAN Introduction  

E-Print Network (OSTI)

SCIENCE AND IMPLEMENTATION PLAN Introduction The cross-cutting review of science and research undertaken by the Government in 2000 identified e-Science as one of three priority research areas, allocating the new industries of the future. The Science Budget defines e-Science as 'science increasingly done

Brierley, Andrew

429

Predictive Maintenance Program Implementation Experience  

Science Conference Proceedings (OSTI)

Predictive maintenance (PDM) is a process of collecting data, assessing machinery condition, and deciding when to perform maintenance. PDM saves money and improves machinery reliability as compared to preventive or corrective maintenance. This report describes the implementation of PDM programs at Commonwealth Edison's (ComEd's) fossil power plants.

1998-12-29T23:59:59.000Z

430

Dynamic Vnodes - design and implementation  

Science Conference Proceedings (OSTI)

Dynamic vnodes make the UNIX kernel responsive to a varying demand for vnodes, without a need to rebuild the kernel. It also optimizes the usage of memory by deallocating excess vnodes. This paper describes the design and implementation of dynamic vnodes ...

Aju John

1995-01-01T23:59:59.000Z

431

implementing bioenergy applied research & development  

E-Print Network (OSTI)

1 A Northern Centre for Renewable Energy implementing bioenergy applied research & development plant measures to become carbon neutral and operate on renewable energy. UNBC is uniquely positioned for Climate Solutions, and UNBC. The Green University Centre will be a model of energy efficiency

Northern British Columbia, University of

432

IPv6 Advanced Protocols Implementation  

Science Conference Proceedings (OSTI)

This book is the second installment of a two-volume series on IPv6 and the KAME implementation. This book discusses those protocols that are found in more capable IPv6 devices, are commonly deployed in more complex IPv6 network environments, or are not ...

Qing Li; Jinmei Tatuya; Keiichi Shima

2007-04-01T23:59:59.000Z

433

The Standards Forum, February 1995  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Volume 3, Number 2 - September 1995 The Standards News on the DOE Technical Standards Program Forum ISO 14000 - An Update Article contributed by Mary McKiel, U.S. Environmental Protection Agency The International Organization for Standardization (ISO) is developing Environmental Management Stan- dards through ISO Technical Commit- tee (TC) 207. The standards are known as the "ISO 14000" series. 1 The standards will cover a broad array of environmental topics including environmental management systems, eco-labeling, life cycle assessment, environment performance evaluation indicators, and environmental aspects in product standards. The standards are management based, not performance based, and are intended to be applicable to virtually all sectors from manufacturing

434

The Standards Forum, April 1996  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 - March 1997 4 - March 1997 The Standards News on the DOE Technical Standards Program Meetings ........................................ 11 Standardization = Improvements .. 12 The OSTI Corner ........................... 12 From the Manager ......................... 2 TSM Spotlight ................................ 3/4 Standards Actions ......................... 5 News Briefs ................................... 10 INSIDE THIS ISSUE (Continued on Page 9) Update on Topical Committees In the June 1996 edition of The Standards Forum, Rick Serbu, DOE Technical Standards Program (TSP) Manager, announced a new program initiative to identify emerging or existing technical working groups of DOE/contractor subject matter experts as DOE "topical" standards committees. Working in cooperation with the TSP, these

435

DOE Technical Standards Program Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 Revision: 4 Date: August 1, 2000 CONVERSION OF DOE TECHNICAL STANDARDS TO NON-GOVERNMENT STANDARDS U.S. Department of Energy Office of Nuclear Safety Policy and Standards Washington, D.C. 20585 DOE-TSPP-10 Conversion Revision: 4 Date: August 1, 2000 DOE Technical Standards Program i CONTENTS Paragraph Page 1. SCOPE........................................................................................................................................... 1 1.1 Purpose ................................................................................................................... 1 1.2 Applicability.............................................................................................................. 1 2. CONVERSION OF DOE TECHNICAL STANDARDS.................................................................... 1

436

Maintenance of DOE Technical Standards  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TECHNICAL STANDARDS TECHNICAL STANDARDS PROGRAM PROCEDURES DOE-TSPP-9 Revision: 5 Date: August 1, 2000 MAINTENANCE OF DOE TECHNICAL STANDARDS U.S. Department of Energy Office of Nuclear Safety Policy and Standards Washington, D.C. 20585 DOE-TSPP-9 Maintenance Revision: 5 Date: August 1, 2000 DOE Technical Standards Program i CONTENTS Paragraph Page 1. SCOPE........................................................................................................................................... 1 1.1 Purpose ................................................................................................................... 1 1.2 Applicability.............................................................................................................. 1

437

DOE Standard 1020 - Natural Phenomena Hazard analysis and Design Criteria  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE Standard 1020 - Natural Phenomena Hazard analysis and Design DOE Standard 1020 - Natural Phenomena Hazard analysis and Design Criteria for DOE Facilities DOE Standard 1020 - Natural Phenomena Hazard analysis and Design Criteria for DOE Facilities Department of Energy (DOE) Standard (STD)-1020-2012, Natural Phenomena Hazards Analysis and Design Criteria for DOE Facilities, provides criteria and guidance for the analysis and design of facility structures, systems, and components (SSCs) that are necessary to implement the requirements of DOE Order (O) 420.1C, Facility Safety, and to ensure that the SSCs will be able to effectively perform their intended safety functions under the effects of natural phenomena hazards (NPHs). This Standard also provides criteria and guidance for the use of industry building codes and voluntary

438

Renewables Portfolio Standard Overview  

DOE Green Energy (OSTI)

A Renewables Portfolio Standard (RPS) is a requirement on electric utilities and other electric suppliers to supply a minimum percentage or amount of their load with eligible sources of renewable energy. The RPS has become increasingly popular because of its benefits and the public benefits of renewable energy. A well-designed state RPS can effectively deliver a renewable energy supply and associated benefits, at a low cost or even with consumer savings. This fact sheet provides an overview of an effective RPS design.

Not Available

2005-02-01T23:59:59.000Z

439

High Availability Electronics Standards  

Science Conference Proceedings (OSTI)

Availability modeling of the proposed International Linear Collider (ILC) predicts unacceptably low uptime with current electronics systems designs. High Availability (HA) analysis is being used as a guideline for all major machine systems including sources, utilities, cryogenics, magnets, power supplies, instrumentation and controls. R&D teams are seeking to achieve total machine high availability with nominal impact on system cost. The focus of this paper is the investigation of commercial standard HA architectures and packaging for Accelerator Controls and Instrumentation. Application of HA design principles to power systems and detector instrumentation are also discussed.

Larsen, R.S.; /SLAC

2006-12-13T23:59:59.000Z

440

STANDARD OPERATING PROTOCOLS FOR DECOMMISSIONING  

SciTech Connect

Decommissioning projects at Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) sites are conducted under project-specific decision documents, which involve extensive preparation time, public comment periods, and regulatory approvals. Often, the decision documents must be initiated at least one year before commencing the decommissioning project, and they are expensive and time consuming to prepare. The Rocky Flats Environmental Technology Site (RFETS) is a former nuclear weapons production plant at which hazardous substances and wastes were released or disposed during operations. As a result of the releases, RFETS was placed on the National Priorities List in 1989, and is conducting cleanup activities under a federal facilities compliance agreement. Working closely with interested stakeholders and state and federal regulatory agencies, RFETS has developed and implemented an improved process for obtaining the approvals. The key to streamlining the approval process has been the development of sitewide decision documents called Rocky Flats Cleanup Agreement Standard Operating Protocols or ''RSOPs.'' RSOPs have broad applicability, and could be used instead of project-specific documents. Although no two decommissioning projects are exactly the same and they may vary widely in contamination and other hazards, the basic steps taken for cleanup are usually similar. Because of this, using RSOPs is more efficient than preparing a separate project-specific decision documents for each cleanup action. Over the Rocky Flats cleanup life cycle, using RSOPs has the potential to: (1) Save over 5 million dollars and 6 months on the site closure schedule; (2) Eliminate preparing one hundred and twenty project-specific decision documents; and (3) Eliminate writing seventy-five closure description documents for hazardous waste unit closure and corrective actions.

Foss, D. L.; Stevens, J. L.; Gerdeman, F. W.

2002-02-25T23:59:59.000Z

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

AEDG Implementation Recommendations: Cooling and Heating Loads | Building  

NLE Websites -- All DOE Office Websites (Extended Search)

Cooling and Heating Loads Cooling and Heating Loads The Advanced Energy Design Guide (AEDG) for Small Office Buildings, 30% series, seeks to achieve 30% savings over ASHRAE Standard 90.1-1999. This guide focuses on improvements to small office buildings, less than 20,000ft2. The recommendations in this article are adapted from the implementation section of the guide and focus on heating and cooling system design loads for the purpose of sizing systems and equipment should be calculated in accordance with generally accepted engineering standards and handbooks such as ASHRAE Handbook--Fundamentals. Publication Date: Wednesday, May 13, 2009 air_cooling_and_heating_loads.pdf Document Details Affiliation: DOE BECP Focus: Compliance Building Type: Commercial Code Referenced: ASHRAE Standard 90.1-1999

442

Glossary | Building Energy Codes Program  

NLE Websites -- All DOE Office Websites (Extended Search)

NAECA NAECA The National Appliance Energy Conservation Act of 1987, 42 USC 6291 et seq., as amended, Public Law 100-12. NAGDM National Association of Garage Door Manufacturers. NCSBCS The National Conference of States on Building Codes and Standards. NEEA Northwest Energy Efficiency Alliance. NEEP Northeast Energy Efficiency Partnerships. Net Wall Area The net wall area includes the opaque wall area of all above-grade walls enclosing conditioned spaces, the opaque area of conditioned basement walls less than 50% below grade (including the below-grade portions), and peripheral edges of floors. The net wall area does not include windows, doors, or other such openings, because they are treated separately. NFPA National Fire Protection Association. NFRC National Fenestration Rating Council.

443

Self-assessment program implementation plan. Revision A  

Science Conference Proceedings (OSTI)

This implementation plan identifies and describes the tasks that must be completed in order to successfully implement a Self-Assessment (SA) Program. The purpose of the Self-Assessment Program is to comply with applicable Department of Energy (DOE) directives and orders, Federal, State, and local regulations, operate the Pinellas Plant according to best management practices, and achieve excellence in all operating areas. The Self-Assessment Program will be applied to the Pinellas Plant facility which includes buildings, grounds, equipment, operations, and activities under the control of line management. Furthermore, all applicable disciplines under environmental protection, safety, health and management will be covered by the program. The Self-Assessment Program has been designed to accomplish the following tasks: define the scope of the Self-Assessment Program; assign organizational roles and responsibilities; address EH and S functional elements and management issues; develop a Self-Assessment program charter and policy; identify all applicable EH and S codes, regulations and standards; develop self-assessment procedures and instructions; generate a Self-Assessment Manual; develop a master schedule for facility appraisals and audits; design checklists and report formats for recording appraisal data; implement an assessment tracking and reporting system; implement a root cause analysis and corrective action system; implement a trend analysis and lessons learned system; and establish a formal training program.

Quets, A.L.

1991-10-23T23:59:59.000Z

444

The Standards Forum, December 1999  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 – December 1999 3 – December 1999 PAGE 1 The Standards News on the DOE Technical Standards Program (Continued on Page 15) 8 Volume 7 – Number 3 – December 1999 B ackground— Congressional Action On March 7, 1996, a major change in how Federal agencies use voluntary standards was made when the President signed the National Technology Transfer and Advance- ment Act (PL 104-113) 1 into law. This Law directs Federal agencies to use technical standards developed by voluntary consen- sus standards bodies, to the extent practicable, to achieve greater reliance on voluntary standards and conformity assess- ment bodies with decreased dependence on government-unique standards. The Law also tasks the Na- tional Institute of Standards and Technology (NIST) with coordinating Federal, state and local standards and confor-

445

(RPP_standards.ps)  

NLE Websites -- All DOE Office Websites (Extended Search)

7 7 10 20 30 40 50 70 100 0.001 0.002 0.005 0.010 0.020 0.050 0.100 0.200 0.500 1.000 Confidence level CL for fits α for confidence intervals 3 4 2 6 8 10 15 20 25 30 40 50 n = 1 χ 2 DEG's Macintosh: Adobe Illus Files/RPP_standards.ps Graphics symbols: 4.25 inches (Sports section) 2.60 inches 3.36 inches (m 1 +m 3 ) 2 10 pt captions 10 pt labels set font basic; set mode vector=off set window x 2 6.5 y 2 5.5 set labels size 1.2 set title size 1.29 set tics size 0.05 4.50 inches (Minireviews) TOPDRAWER template: PARTICLE DATA GROUP NOTES PDG-93-05 10 November 1993 Standards for Adobe Illustrator figures in the Review of Particle Properties

446

Exceptional Supersymmetric Standard Model  

E-Print Network (OSTI)

We discuss some phenomenological aspects of an $E_6$ inspired supersymmetric standard model with an extra $U(1)_{N}$ gauge symmetry under which right-handed neutrinos have zero charge, allowing a conventional see-saw mechanism. The $\\mu$ problem is solved in a similar way to the NMSSM, but without the accompanying problems of singlet tadpoles or domain walls. The above exceptional supersymmetric standard model (ESSM) involves the low energy matter content of three 27 representations of $E_6$, which is broken at the GUT scale, and allows gauge coupling unification due to an additional pair of Higgs-like doublets. The ESSM predicts a $Z'$ boson and exotic quarks which, if light enough, will provide spectacular new physics signals at the LHC. We study the LHC phenomenology of the $Z'$ and extra quarks, including their production and decay signatures particular to the ESSM. We also discuss the two-loop upper bound on the mass of the lightest CP-even Higgs boson, and show that it can be significantly heavier than in either the MSSM or the NMSSM.

S. F. King; S. Moretti; R. Nevzorov

2005-11-22T23:59:59.000Z

447

LANL PDMLink Product Structure Implementation  

Science Conference Proceedings (OSTI)

Over the past 2 and a half years LANL has done both functionality exploration as well as production implementations of PDMLink Product Structure to control the configuration of many of the LANL Design Agency Products. Based on this experience LANL has been recommending for over a year that future product structure implementation in PDMLink do not use the two digit suffix in the number field of enterprise parts (or WTParts). The suffix will be part of one of the attributes for Part Number. Per the TBP's the two digit suffix represents a change in form, fit, or function in a part or a change in the production agency or a number of other conditions. It also denotes backward compatibility with earlier suffixed parts (see TBP 402 section 3.1).

Scully, Christopher J. [Los Alamos National Laboratory

2012-08-29T23:59:59.000Z

448

Status of conversion of NE standards to national consensus standards  

SciTech Connect

This report is a summary of the activities that have evolved to effect conversion of nuclear energy standards to national consensus standards, and the status of current conversion activities.

Hudson, R.C.; McKee, R.O.

1989-03-01T23:59:59.000Z

449

State options in lighting: efficiency standards for existing public buildings  

SciTech Connect

This report discusses requirements and options for state lighting-efficiency standards for existing public buildings under the Energy Policy and Conservation Act. EPCA, as implemented under present regulations, is found to allow great flexibility to the states in what they adopt, so long as they do adopt some standard. A wide variety of substantive standards is described, and it is recommended that states adopt a standard based on a maximum-lighting power budget with cost-effectiveness criteria. Several options for adoption and enforcement of standards are discussed. It is recommended that states adopt a requirement that owners of all public buildings submit reports of lighting energy audits and estimates of energy savings from modifications to comply with substantive standards. It is further recommended that while filing of reports should be mandatory, substantive compliance, at least initially, need not be; if it turns out that voluntary compliance is not great enought to achieve a state's desired energy savings, compliance could then be made mandatory. It is recommended that exemptions from the standards be limited to small buildings and that variances under a mandatory standard be available only when an applicant can show insufficient capital to make required modifications, even though they would soon pay for themselves in reduced operating costs. It is suggested that a lighting standard of the kind recommended could substantially reduce wasted energy in lighting, be simple enough to be easily understood and applied, be technically and economically reasonable, and allow for needed exemptions without loopholes.

Meeker, F.

1979-07-01T23:59:59.000Z

450

Quantum computers: Definition and implementations  

Science Conference Proceedings (OSTI)

The DiVincenzo criteria for implementing a quantum computer have been seminal in focusing both experimental and theoretical research in quantum-information processing. These criteria were formulated specifically for the circuit model of quantum computing. However, several new models for quantum computing (paradigms) have been proposed that do not seem to fit the criteria well. Therefore, the question is what are the general criteria for implementing quantum computers. To this end, a formal operational definition of a quantum computer is introduced. It is then shown that, according to this definition, a device is a quantum computer if it obeys the following criteria: Any quantum computer must consist of a quantum memory, with an additional structure that (1) facilitates a controlled quantum evolution of the quantum memory; (2) includes a method for information theoretic cooling of the memory; and (3) provides a readout mechanism for subsets of the quantum memory. The criteria are met when the device is scalable and operates fault tolerantly. We discuss various existing quantum computing paradigms and how they fit within this framework. Finally, we present a decision tree for selecting an avenue toward building a quantum computer. This is intended to help experimentalists determine the most natural paradigm given a particular physical implementation.

Perez-Delgado, Carlos A.; Kok, Pieter [Department of Physics and Astronomy, University of Sheffield, Hicks Building, Hounsfield Road, Sheffield, S3 7RH (United Kingdom)

2011-01-15T23:59:59.000Z

451

Labor Standards Interview Form | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards Interview Form Labor Standards Interview Form SF 1445.pdf More Documents & Publications Labor Standards for Construction Chapter 22 - Labor Standards for Construction CRB...

452

Past DOE Technical Standards Program Procedures | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Information Center DOE Technical Standards Program DOE Technical Standards Procedures Past DOE Technical Standards Program Procedures Past DOE Technical Standards Program...

453

Labor Standards for Construction | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Labor Standards for Construction Labor Standards for Construction Labor Standards for Construction More Documents & Publications Chapter 22 - Labor Standards for Construction Labor...

454

Approved DOE Technical Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE Technical Standards Approved DOE Technical Standards DOE Technical Standards Program August 16, 2013 Technical Standards, DOE-HDBK-1108-2002 Change Notice 2 (July 2013)...

455

DOE Technical Standards Program Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 Revision: 4 Date: August 1, 2000 USE OF VOLUNTARY CONSENSUS STANDARDS AND INTERACTION WITH STANDARDS DEVELOPMENT ORGANIZATIONS U.S. Department of Energy Office of Nuclear Safety Policy and Standards Washington, D.C. 20585 Standards Use / Participation DOE-TSPP-3 Revision: 4 Date: August 1, 2000 i PAGE INTENTIONALLY BLANK DOE-TSPP-3 Standards Use / Participation Revision: 4 Date: August 1, 2000 DOE Technical Standards Program ii CONTENTS Paragraph Page 1. SCOPE.............................................................................................................................................1 1.1 Purpose ................................................................................................................... 1 1.2 Applicability.............................................................................................................. 1

456

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Commercial Fed. Government Industrial Local Government Nonprofit Residential Schools State Government Savings Category Bioenergy Buying & Making Electricity Solar Wind Program Info State Nevada Program Type Interconnection Provider Public Utilities Commission of Nevada In December 2003, the Nevada Public Utilities Commission (PUC) adopted interconnection standards for customers of NV Energy (formerly Nevada Power and Sierra Pacific Power) with on-site generation up to 20 megawatts (MW) in capacity. These standards are largely consistent with IEEE 1547 standards, California's interconnection rule (California Rule 21) and the model interconnection agreement developed by the National Association of

457

Facility Representative Program: Qualification Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Training & Qualification Information Training & Qualification Information Qualification Standards DOE Order Self-Study Modules DOE Fundamentals Handbooks Nuclear Safety Basis Self-Study Guide Energy Online Courses Available Link to National Training Center Basic Courses for Facility Representative Qualification Recommended Courses to Expand Facility Representative's Knowledge Base Qualification Standards General Technical Base Qualification Standard, Qualification Card & Reference Guide -- GTB Qualification Standard (DOE-STD-1146-2007), December 2007 [PDF] -- GTB Qualification Card, December 2007 [DOC] -- GTB "Gap" Qualification Card, December 2007 [DOC] -- GTB Qualification Standard Reference Guide, May 2008 [PDF] Facility Representative Qualification Standard, Qualification Card & Reference Guide

458

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Ceiling Fans Energy Conservation Standards Ceiling Fans Energy Conservation Standards Sign up for e-mail updates on regulations for this and other products The Department of Energy (DOE) is considering establishing energy conservation standards for residential ceiling fans. There are currently federal design standards and test procedures for ceiling fans, but no energy conservation standards. Recent Updates | Public Meeting Information | Submitting Public Comments | Milestones and Documents | Related Rulemakings | Statutory Authority | Contact Information Recent Updates DOE published a request for information regarding energy conservation standards for ceiling fans. 78 FR 62494 (October 22, 2013). Public Meeting Information No public meeting is scheduled at this time. Submitting Public Comments

459

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Agricultural Commercial Fed. Government Industrial Institutional Local Government Nonprofit Residential Schools State Government Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Energy Sources Solar Home Weatherization Wind Program Info State Pennsylvania Program Type Interconnection Provider Pennsylvania Public Utility Commission The Pennsylvania Public Utilities Commission was required to adopt interconnection standards and net-metering rules by the Alternative Energy Portfolio Standards Act of 2004.The PUC subsequently adopted interconnection standards for net-metered distributed generation (DG)

460

The Standards Forum, December 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 – December 2000 3 – December 2000 PAGE 1 The Standards News on the DOE Technical Standards Program A Note From the Manager ............. 2 TSM Spotlight ................................ 5 INSIDE THIS ISSUE Quality Problems? .......................... 6 Welcome New TSMs ..................... 6 New DAS ....................................... 7 Continuous Improvement ............... 7 Standards Actions .......................... 8 Topical Committees ....................... 12 OMB A-119 Report ......................... 13 News Briefs ................................... 14 Upcoming Meetings ....................... 17 Volume 8 – Number 3 – December 2000 By Rick Serbu, Manager, DOE Technical Standards Program The American National Standards Institute (ANSI) approved a National Standards Strategy (NSS) for the United States on

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Agricultural Commercial Fed. Government Industrial Institutional Local Government Nonprofit Residential Schools State Government Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Wind Energy Sources Solar Home Weatherization Water Program Info State North Carolina Program Type Interconnection Provider North Carolina Utilities Commission The North Carolina Utilities Commission (NCUC) adopted comprehensive interconnection standards for distributed generation in June 2008. The NCUC standards, which are similar to the Federal Energy Regulatory Commission's (FERC) interconnection standards for small generators,

462

STANDARD FORM NO. 64  

Office of Legacy Management (LM)

/qz-5 /qz-5 STANDARD FORM NO. 64 rl . . .' . , G Ojice Memoawl crl LA STATES GOVER pi,+ ip; ; / (' , TO : F. M . Belmore, M remtor, Produution Division DATE: Deomnber FROM : R. F. Van Wy TV Mvision of Teohnioal Advisers SUBJECT: R?IQUEST FOR&m SYMBOL: TA:RFV:rle For use under ooxrkraot AT-300l=Gen-72 at Columibia University, m request 6 pieoes Of A toleranoe of plus ordinary uranium out to the sizes listed below. or llliZlU8 l/16" i8 sati8faotory. P x 1u x 1" 1" x 1 !k x 1" tixl x1" 3P 4 x 12 x 1" ororr-se&ion of l;% x 1" are reque8ted, rq~are to 2" square are aomptable. Please 1. 1. Havena, Pupin Phy8ioe Laboratory, Columbia University, New York City. 2 pieoerr 2 piece8 2 pieoea 2 pieces Although pieces with a

463

Better Standards, less Ambiguity  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

iT Helps with Plant Security iT Helps with Plant Security engineers ensure Plant Uptime engineers Building Models Better Standards, less Ambiguity Department of energy on Cyber Security exclusive interview Special Pullout Section Packaging Automation review June 2008 FIFTH ANNIVERSARY ISSUE Among the many initiatives aimed at providing cyber security for the nation's critical infrastructure, the effort that led to a January 2006 document known as the "Roadmap to Secure Control Systems in the Energy Sector" stands out as one involving significant public/private sector collaboration. The Roadmap, which lays out a 10-year vision, has been recommended by the Na- tional Infrastructure Advisory Council as a model for other industries to follow in developing their own sector-specific

464

Microfabricated ion frequency standard  

DOE Patents (OSTI)

A microfabricated ion frequency standard (i.e. an ion clock) is disclosed with a permanently-sealed vacuum package containing a source of ytterbium (Yb) ions and an octupole ion trap. The source of Yb ions is a micro-hotplate which generates Yb atoms which are then ionized by a ultraviolet light-emitting diode or a field-emission electron source. The octupole ion trap, which confines the Yb ions, is formed from suspended electrodes on a number of stacked-up substrates. A microwave source excites a ground-state transition frequency of the Yb ions, with a frequency-doubled vertical-external-cavity laser (VECSEL) then exciting the Yb ions up to an excited state to produce fluorescent light which is used to tune the microwave source to the ground-state transition frequency, with the microwave source providing a precise frequency output for the ion clock.

Schwindt, Peter (Albuquerque, NM); Biedermann, Grant (Albuquerque, NM); Blain, Matthew G. (Albuquerque, NM); Stick, Daniel L. (Albuquerque, NM); Serkland, Darwin K. (Albuquerque, NM); Olsson, III, Roy H. (Albuquerque, NM)

2010-12-28T23:59:59.000Z

465

The Standards Actions, January 1996  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Actions Actions Resistance of HVAC Air Ducts and Fittings (new standard); comments due February 6, 1996. * ISO/ASQC A3534-1, Statis- tics - Vocabulary and Sym- bols - Probability and Gen- eral Statistical Terms (new standard); comments due January 26, 1996. * ISO/ASTM/ASQC/NSF 14004, Environmental management systems - General guidelines on principles, systems and Technical Standards Program Document Status as of 12/31/95 Documents Recently Published The Technical Standards Program is sponsoring a project at OSTI to place all DOE technical standards (i.e., standards and handbooks) on the Internet. To date, 57 DOE technical standards have been placed on the Internet at the following address: http://apollo.osti.gov/ html/techstds/ techstds.html The following DOE technical standards have recently

466

Standards and Related Texts Reference  

E-Print Network (OSTI)

A list of existing Codex standards and related texts whose revocation is recommended is presented below. The Commission is invited to confirm the revocation of existing Codex standards and related texts, as recommended by Codex Committees.

Th Session

2011-01-01T23:59:59.000Z

467

DOE Technical Standards Program Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

A TECHNICAL STANDARD U.S. Department of Energy Office of Nuclear Safety Policy and Standards Washington, D.C. 20585 DOE-TSPP-2 Need Revision: 4 Date: August 1, 2000 DOE...

468

Journeys Beyond the Standard Model  

E-Print Network (OSTI)

for the standard model Higgs boson in pp collisions at s = 7for ? the Standard Model Higgs boson using up to 4.9 fb oftwo component fields of Eq. higgs boson is then a linear

Elor, Gilly

2013-01-01T23:59:59.000Z

469

Brochure HI Standards Subscription Options  

Energy.gov (U.S. Department of Energy (DOE))

HIs Web-based Standards packages will provide you with all of the Standards appropriate for a specific pump technology. Select the package that is right for your business and the number of...

470

Appliance Standards and Building Codes  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Program Manager Presentation Program Manager Presentation Appliance Standards and Building Codes John Cymbalsky U.S Department of Energy - Building Technologies Office john.cymbalsky@ee.doe.gov 202.287.1692 2 | Building Technologies Office eere.energy.gov Appliance Standards and Building Codes Program Goals Appliance Standards Program Goals Provide cost-effective energy savings through national appliance and equipment standards: Issue 23 final rules by end of FY2015 Deliver at least 1 qBtu of savings annually by

471

MEMS Measurement Science and Standards  

Science Conference Proceedings (OSTI)

MEMS Measurement Science and Standards. Summary: Our goal is to provide technical leadership in R&D for the MEMS ...

2013-05-09T23:59:59.000Z

472

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

efficient signal modules can result in significant energy savings. Recent Updates | Standards | Test Procedures | Waiver, Exception, and Exemption Information | Statutory...

473

Chemistry Standard Reference Materials News  

Science Conference Proceedings (OSTI)

... Researchers from the National Institute of Standards and Technology (NIST) and the US Army Dugway (Utah) Proving Ground have developed ...

2010-08-19T23:59:59.000Z

474

Chemistry Standard Reference Data News  

Science Conference Proceedings (OSTI)

... Researchers from the National Institute of Standards and Technology (NIST) and the US Army Dugway (Utah) Proving Ground have developed ...

2010-08-25T23:59:59.000Z

475

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Submitting Public Comments The comment period is closed. Milestones and Documents The residential dehumidifiers energy conservation standards rulemaking docket...

476

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Submitting Public Comments The comment period is closed. Milestones and Documents The residential water heaters energy conservation standards rulemaking docket...

477

LLL calibration and standards facility  

SciTech Connect

The capabilities of Lawrence Livermore Laboratory's Calibration and Standards Facility are delineated. The facility's ability to provide radiation fields and measurements for a variety of radiation safety applications and the available radiation measurement equipment are described. The need for national laboratory calibration labs to maintain traceability to a national standard are discussed as well as the areas where improved standards and standardization techniques are needed.

Campbell, G.W.; Elliott, J.H.

1980-04-15T23:59:59.000Z

478

NIST Global Standards Information Events  

Science Conference Proceedings (OSTI)

... MENA Quality Infrastructure Stakeholders Meeting Jun 21-22, 2010 ( Amman, JORDAN ) Event Organizer: NIST & Jordan Institution of Standards & ...

479

NIST Global Standards Information Jordan  

Science Conference Proceedings (OSTI)

... Regions >; Middle East/North Africa >; Jordan >. World Guide to Standards Resources: JORDAN. ... Export Resource: US Commercial Service Jordan. ...

480

NIST Global Standards Information Pakistan  

Science Conference Proceedings (OSTI)

... Regions >; Central & South Asia >; Pakistan >. World Guide to Standards Resources: PAKISTAN. ... Export Resource: US Commercial Service Pakistan ...

Note: This page contains sample records for the topic "naeca standards implemented" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

NIST Global Standards Information Pakistan  

Science Conference Proceedings (OSTI)

... Workshop for the Middle East, North Africa and Pakistan on Standards, Codes, and Conformity Assessment for Life Safety and Building. ...

482

DOE Technical Standards Program Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 Revision: 4 Date: August 1, 2000 APPROVING AND ISSUING DOE TECHNICAL STANDARDS U.S. Department of Energy Office of Nuclear Safety Policy and Standards Washington, D.C. 20585 DOE-TSPP-8 Approval Revision: 4 Date: August 1, 2000 DOE Technical Standards Program i CONTENTS Paragraph Page 1. SCOPE........................................................................................................................................... 1 1.1 Purpose ................................................................................................................... 1 1.2 Applicability.............................................................................................................. 1 2. APPROVING AND ISSUING DOE TECHNICAL STANDARDS .................................................... 1

483

DOE Technical Standards Program Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Revision: 4 Date: August 1, 2000 TECHNICAL STANDARDS PROGRAM RESPONSIBILITIES U.S. Department of Energy Office of Nuclear Safety Policy and Standards Washington, D.C. 20585 DOE-TSPP-1 Responsibilities Revision: 4 Date: August 1, 2000 DOE Technical Standards Program i CONTENTS Paragraph Page 1. SCOPE........................................................................................................................................... 1 1.1 Purpose ................................................................................................................... 1 1.2 Applicability.............................................................................................................. 1 2. PROGRAM RESPONSIBILITIES ................................................................................................... 1

484

Implementing enterprise resource planning systems: organizational performance and the duration of the implementation  

Science Conference Proceedings (OSTI)

This paper examines the impact of the duration of ERP implementation on firm performance both during and after implementation. Organizations choose either an accelerated implementation approach or a traditional (longer) implementation approach. The former ... Keywords: Enterprise resource planning, Firm performance, IT implementation

Mark Anderson; Rajiv D. Banker; Nirup M. Menon; Jorge A. Romero

2011-09-01T23:59:59.000Z

485

An Effective Implementation of Operational Inventory Management  

E-Print Network (OSTI)

This Record of Study describes the Doctor of Engineering (DE) internship experience at the Supply Chain Systems Laboratory (SCSL) at Texas A&M University. The objective of the internship was to design and develop automation tools to streamline lab operations related to inventory management projects and during that process adapt and/or extend theoretical inventory models according to real-world business complexity and data integrity problems. A holistic approach to automation was taken to satisfy both short-term and long-term needs subject to organizational constraints. A comprehensive software productivity tool was designed and developed that considerably reduced time and effort spent on non-value adding activities. This resulted in standardizing and streamlining data analysis related activities. Real-world factors that significantly influence the data analysis process were identified and incorporated into model specifications. This helped develop an operational inventory management model that accounted for business complexity and data integrity issues commonly encountered during implementation. Many organizational issues including new business strategies, human resources, administration, and project management were also addressed during the course of the internship.

Sellamuthu, Sivakumar

2009-05-01T23:59:59.000Z

486

Accelerating the Adoption of Second-Tier Reach Standards forApplicable Appliance Products in China  

Science Conference Proceedings (OSTI)

The minimum energy efficiency standards program for household appliances in China was initiated in 1989. Since 1996, CLASP and its implementing partner, LBNL, have assisted China in developing 11 minimum energy performance standards (MEPS) for 9 products and endorsement labels for 11 products including: refrigerators; air conditioners; clothes washers; televisions; printers; computers; monitors; fax machines; copiers; DVD/VCD players; external power supplies; and set-top boxes (under development). Before 2003, China's traditional approach to standards development involved small increases in efficiency requirements for implementation within 6 months of a standard's approval. Since 2003, China has adopted a new approach in setting MEPS. This new approach involves the development of two tiers of standards--one for initial implementation and a second tier at a more aggressive level of energy efficiency for implementation three to five years later. The second-tier standard is also referred to as a 'reach standard'. Reach standards have now been developed in China for: color TVs; refrigerators; air conditioners; and external power supplies. This report is presented in five sections. After the introduction in Section 1, Section 2 analyzes the distribution of the efficiency of refrigerators and air-conditioners in China based on data collected by the China Energy Label Center for the mandatory energy information label program. The results provide an assessment of the adoption of reach standards for these two products. Section 3 summarizes on-going collaborations with Shanghai related to early local adoption of reach standards, and presents both the impact and an analysis of barriers to the local adoption of reach standard for air-conditioners. Section 4 offers suggestions for local governments on how to move forward in adopting reach standards in their localities and concludes with a summary of the results and a plan for developing local capacity in order to achieve success in adopting reach standards.

Lin, Jiang; Fridley, David

2007-03-01T23:59:59.000Z

487

HW/SW for an intelligent transducer network based on IEEE 1451 standard  

Science Conference Proceedings (OSTI)

This work describes a hardware/software co-design system development, named IEEE 1451 platform, to be used in process automation. This platform intends to make easier the implementation of IEEE standards 1451.0, 1451.1, 1451.2 and 1451.5. The hardware ... Keywords: FPGA, IEEE 1451 standard, Intelligent transducers, NIOS II processor

E. A. Batista; L. Gonda; A. C. R. da Silva; S. R. Rossi; M. C. Pereira; A. A. de Carvalho; C. E. Cugnasca

2012-01-01T23:59:59.000Z

488

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Commercial Fed. Government Industrial Institutional Local Government Nonprofit Residential Schools State Government Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Wind Energy Sources Solar Home Weatherization Program Info State Michigan Program Type Interconnection Provider Michigan Public Service Commission The Michigan Public Service Commission (PSC) first adopted interconnection standards for distributed generation (DG) in September 2003. The original standards provided for 5 levels of interconnection with cutoffs at 30 kilowatts (kW), 150 kW, 750 kW, and 2 megawatts (MW), but left many details

489

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Agricultural Commercial Fed. Government Industrial Institutional Local Government Nonprofit Residential Schools State Government Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Solar Wind Program Info State Oregon Program Type Interconnection Provider Oregon Public Utility Commission Oregon has three separate interconnection standards: one for net-metered systems, one for small generator facilities (non-net metered systems) and one for large generator facilities (non-net metered systems). Oregon has also established separate net metering requirements and interconnection standards for the state's primary investor-owned utilities (PGE and

490

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Agricultural Commercial Fed. Government Industrial Institutional Local Government Multi-Family Residential Nonprofit Residential Schools State Government Savings Category Bioenergy Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Solar Water Wind Program Info State New Jersey Program Type Interconnection Provider New Jersey Board of Public Utilities New Jersey's interconnection standards apply statewide to all electric distribution utilities, but not to the small number of municipal utilities and electric cooperatives in the state. The rules, first adopted in 2001, have been revised several times since their inception, most recently in May 2012. The current standards include the following basic provisions:

491

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Agricultural Commercial Fed. Government Industrial Institutional Local Government Nonprofit Residential Schools State Government Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Wind Energy Sources Solar Home Weatherization Program Info State District of Columbia Program Type Interconnection Provider Washington Utilities and Transportation Commission In September 2007, the Washington Utilities and Transportation Commission (UTC) adopted interconnection standards for distributed generation (DG) systems up to 20 megawatts (MW) in capacity. The revised standards provide for two separate levels of interconnection based on system capacity. The

492

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Agricultural Commercial Industrial Institutional Nonprofit Residential Schools Utility Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Wind Energy Sources Solar Program Info State Colorado Program Type Interconnection Provider Colorado Public Utilities Commission In December 2005, the Colorado Public Utilities Commission (PUC) adopted standards for net metering and interconnection, as required by Amendment 37, a renewable-energy ballot initiative approved by Colorado voters in November 2004. The PUC standards generally apply to utilities with 40,000 or more customers and all cooperative utilities.*

493

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Commercial Fed. Government Industrial Institutional Local Government Low-Income Residential Multi-Family Residential Nonprofit Residential Schools State Government Savings Category Bioenergy Biofuels Alternative Fuel Vehicles Commercial Heating & Cooling Manufacturing Buying & Making Electricity Hydrogen & Fuel Cells Water Wind Energy Sources Solar Home Weatherization Program Info State Wisconsin Program Type Interconnection Provider Public Service Commission of Wisconsin In February 2004, the Wisconsin Public Service Commission adopted interconnection standards for distributed generation (DG) systems up to 15 megawatts (MW) in capacity. All investor-owned utilities (IOUs) and municipal utilities are required to abide by the standard provisions.

494

The Standards Forum - March, 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 – March 2000 4 – March 2000 PAGE 1 The Standards News on the DOE Technical Standards Program A Note From the Manager ............. 2 Are You A Player? .................. 2 INSIDE THIS ISSUE TSM Welcome ............................... 3 TSM Spotlight ................................ 4 Saving Through Sharing ................. 5 Upcoming Meetings ....................... 6 Standards Actions .......................... 7 Topical Committees ....................... 12 News Briefs ................................... 14 Volume 7 – Number 4 – March 2000 (Continued on Page 15) 8 Introduction The National Technology Transfer and Ad- vancement Act (NTTAA) provides impetus for NIST’s standards activities. This law di- rects NIST to provide public sector leadership for voluntary standards

495

The Standards Forum, September 1999  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 – September 1999 2 – September 1999 PAGE 1 The Standards News on the DOE Technical Standards Program A Note From the Manager ............. 2 TSM Spotlight ........................... 3 TSM Spotlight ................................ 4 Topical Committees ....................... 5 Standards Actions .......................... 7 News Briefs ................................... 11 FAQs ............................................. 14 Upcoming Meetings ....................... 15 TSMC Telecons ............................. 16 Volume 7 – Number 2 – September 1999 Savannah River Targets Cost Savings Through Standards Reduction By Art Blanchard, Savannah River Site In 1995, the Savannah River Site (SRS) initi- ated a cost-effective task to have the site’s standards system mandate usage of national codes and stan-

496

Interconnection Standards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interconnection Standards Interconnection Standards Interconnection Standards < Back Eligibility Agricultural Commercial Fed. Government Industrial Institutional Local Government Nonprofit Residential Schools State Government Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Wind Energy Sources Solar Program Info State New York Program Type Interconnection Provider New York State Department of Public Service New York first adopted uniform interconnection standards in 1999 (see history below). The Standard Interconnection Requirements (SIR) have subsequently been amended several times since, most recently with the adoption of far reaching revisions in February 2009. Several more minor

497

NIST: Marie Curie and the NBS Radium Standards - Present ...  

Science Conference Proceedings (OSTI)

... Hnigschmid mass standards. The three original standards, Secondary Standard No. 6 from 1913 and Standards Nos. ...

2013-03-21T23:59:59.000Z

498

Standards application and development plan for solar thermal technologies  

DOE Green Energy (OSTI)

The Solar Energy Research Institute, at the request of DOE, is developing a Quality Assurance and Standards (QA and S) Plan for solar thermal technologies. Unlike the legislative directives concerning standards for the Photovoltaic (PV) and Solar Heating and Cooling of Buildings (SHAC) programs, which required prior development of criteria, relevant legal requirements for ST involved developing sound commercial practices. Since standards development and implementation of PV and SHAC technologies were begun earlier, a lessons-learned approach is used to develop a QA and S plan for ST. Thus, the keystone of the plan is a series of functional and standards matrices, contained in this report, developed from input from ST users and from the industry that will be continually reviewed and updated as commercial aspects develop. The matrices highlight codes, standards, test methods, functions and definitions that need to be developed. They will be submitted through ANSI for development by national consensus bodies. A contingency action is proposed for standards development if specific input is lacking at the committee level or if early development of a standard would hasten commercialization or gain needed jurisdictional acceptance. Agency funding will be sought before consensus review to support development of draft standards by specialists, laboratories, and consultants where qualifying requirements apply.

Cobb, H.R.W.

1981-07-01T23:59:59.000Z

499

An energy standard for residential buildings in south China  

SciTech Connect

To curb the spiraling demand for building energy use, China's Ministry of Construction has worked at developing and implementing building energy standards, starting with a standard for heated residential buildings in the Cold regions in 1986, followed by a standard for residential buildings in the Hot Summer Cold Winter Region in central China in 2001. In July 2001, a similar effort was started to develop a standard for residential buildings in the Hot Summer Warm Winter Region, comprising of the entirety or large portions of Guangdong, Guangxi, Hainan and Fujian. The target for the standard is to improve the thermal efficiency of buildings by 50 percent compared to current construction, which are typically uninsulated and have single-pane windows. Because of the importance of controlling window solar gain, the standard developed tables specifying the required window thermal transmittance and shading coefficient for differing window-to-wall ratios. The intent of such trade-off table is to permit flexibility in the location and size of windows, as long as their thermal performances meet the requirements of the standard. For further flexibility, the standard provides three methods of compliance: (1) a simple set of prescriptive requirements, (2) a simplified performance calculation, and (3) a detailed computer-based performance calculation using a Custom Budget approach.

Huang, Yu Joe; Lang, Siwei; Hogan, John; Lin, Haiyan

2003-07-01T23:59:59.000Z

500

Announcing the Standard for Personal Identity Verification ...  

Science Conference Proceedings (OSTI)

... security technology advances, the need ... Standardization (ISO)/International Electrotechnical Commission ... to utilize Advanced Encryption Standard ...

2013-09-05T23:59:59.000Z