Powered by Deep Web Technologies
Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Municipal Solid Waste:  

U.S. Energy Information Administration (EIA) Indexed Site

Methodology for Allocating Municipal Solid Waste Methodology for Allocating Municipal Solid Waste to Biogenic and Non-Biogenic Energy May 2007 Energy Information Administration Office of Coal, Nuclear, Electric and Alternate Fuels U.S. Department of Energy Washington, DC 20585 This report was prepared by the Energy Information Administration, the independent statistical and analytical agency within the U.S. Department of Energy. The information contained herein should be attributed to the Energy Information Administration and should not be construed as advocating or reflecting any policy of the Department of Energy or any other organization. Contact This report was prepared by staff of the Renewable Information Team, Coal, Nuclear, and Renewables Division, Office of Coal, Nuclear, Electric and Alternate Fuels.

2

Municipal Solid Waste | Open Energy Information  

Open Energy Info (EERE)

Waste Jump to: navigation, search TODO: Add description List of Municipal Solid Waste Incentives Retrieved from "http:en.openei.orgwindex.php?titleMunicipalSolidWaste&oldid...

3

Municipal Solid Waste Resources and Technologies  

Energy.gov (U.S. Department of Energy (DOE))

This page provides a brief overview of municipal solid waste energy resources and technologies supplemented by specific information to apply waste to energy within the Federal sector.

4

Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume...  

Office of Environmental Management (EM)

1: Availability of Feedstock and Technology Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume 1: Availability of Feedstock and Technology Municipal solid waste (MSW) is...

5

Experimental analysis of municipal solid waste samples  

E-Print Network (OSTI)

In the analysis of municipal solid waste consolidation, large-scale devices are usually used to measure the compression and hydraulic conductivity parameters. The use of those devices is justified due to difficulties in probing undisturbed samples...

Mendoza Sanchez, Itza

2012-06-07T23:59:59.000Z

6

Municipal Solid WasteMunicipal Solid Waste Landfills In CitiesLandfills In Cities  

E-Print Network (OSTI)

Municipal Solid WasteMunicipal Solid Waste Landfills In CitiesLandfills In Cities ArunArun PurandarePurandare Eco Designs India Pvt. Ltd.Eco Designs India Pvt. Ltd. #12;What is a Landfill? A sanitary landfill refers to an engineered facility for the disposal of MSW designed and operated

Columbia University

7

Aluminum Waste Reaction Indicators in a Municipal Solid Waste Landfill  

E-Print Network (OSTI)

Aluminum Waste Reaction Indicators in a Municipal Solid Waste Landfill Timothy D. Stark, F.ASCE1 landfills may contain aluminum from residential and commercial solid waste, industrial waste, and aluminum, may react with liquid in a landfill and cause uncontrolled temperature increases, significant changes

8

Municipal Solid Waste Resources and Technologies | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Municipal Solid Waste Resources and Technologies Municipal Solid Waste Resources and Technologies Municipal Solid Waste Resources and Technologies October 7, 2013 - 9:28am Addthis Black and white photo of a bulldozer pushing a large mound of trash in a landfill. The National Renewable Energy Laboratory's high-solids digester converts wastes to biogas and compost for energy production. This page provides a brief overview of municipal solid waste energy resources and technologies supplemented by specific information to apply waste to energy within the Federal sector. Overview Municipal solid waste, also known as waste to energy, generates electricity by burning solid waste as fuel. This generates renewable electricity while also incinerating landfill and other municipal waste products such as trash, yard clippings and debris, furniture, food scraps, and other

9

Municipal Solid Waste Resources and Technologies | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Municipal Solid Waste Resources and Technologies Municipal Solid Waste Resources and Technologies Municipal Solid Waste Resources and Technologies October 7, 2013 - 9:28am Addthis Black and white photo of a bulldozer pushing a large mound of trash in a landfill. The National Renewable Energy Laboratory's high-solids digester converts wastes to biogas and compost for energy production. This page provides a brief overview of municipal solid waste energy resources and technologies supplemented by specific information to apply waste to energy within the Federal sector. Overview Municipal solid waste, also known as waste to energy, generates electricity by burning solid waste as fuel. This generates renewable electricity while also incinerating landfill and other municipal waste products such as trash, yard clippings and debris, furniture, food scraps, and other

10

Municipal solid waste disposal in Portugal  

SciTech Connect

In recent years municipal solid waste (MSW) disposal has been one of the most important environmental problems for all of the Portuguese regions. The basic principles of MSW management in Portugal are: (1) prevention or reduction, (2) reuse, (3) recovery (e.g., recycling, incineration with heat recovery), and (4) polluter-pay principle. A brief history of legislative trends in waste management is provided herein as background for current waste management and recycling activities. The paper also presents and discusses the municipal solid waste management in Portugal and is based primarily on a national inquiry carried out in 2003 and directed to the MSW management entities. Additionally, the MSW responsibility and management structure in Portugal is presented, together with the present situation of production, collection, recycling, treatment and elimination of MSW. Results showed that 96% of MSW was collected mixed (4% was separately collected) and that 68% was disposed of in landfill, 21% was incinerated at waste-to-energy plants, 8% was treated at organic waste recovery plants and 3% was delivered to sorting. The average generation rate of MSW was 1.32 kg/capita/day.

Magrinho, Alexandre [Mechanical Engineering Department, Escola Superior de Tecnologia de Setubal, Campus IPS, Estefanilha, Setubal (Portugal); Didelet, Filipe [Mechanical Engineering Department, Escola Superior de Tecnologia de Setubal, Campus IPS, Estefanilha, Setubal (Portugal); Semiao, Viriato [Mechanical Engineering Department, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisbon (Portugal)]. E-mail: ViriatoSemiao@ist.utl.pt

2006-07-01T23:59:59.000Z

11

Nonlinear Model Predictive Control of Municipal Solid Waste Combustion Plants  

E-Print Network (OSTI)

. Also, the energy that results from waste combustion is often used to produce heat and/or electricityNonlinear Model Predictive Control of Municipal Solid Waste Combustion Plants M. Leskens , R.h.Bosgra@tudelft.nl, p.m.j.vandenhof@tudelft.nl Keywords : nonlinear model predictive control, municipal solid waste

Van den Hof, Paul

12

Municipal solid waste effective stress analysis  

SciTech Connect

The mechanical behavior of municipal solid waste (MSW) has attracted the attention of many researchers in the field of geo-environmental engineering in recent years and several aspects of waste mechanical response under loading have been elucidated. However, the mechanical response of MSW materials under undrained conditions has not been described in detail to date. The knowledge of this aspect of the MSW mechanical response is very important in cases involving MSW with high water contents, seismic ground motion and in regions where landfills are built with poor operation conditions. This paper presents the results obtained from 26 large triaxial tests performed both in drained and undrained conditions. The results were analyzed taking into account the waste particles compressibility and the deformation anisotropy of the waste samples. The waste particles compressibility was used to modify the Terzaghi effective stress equation, using the Skempton (1961) proposition. It is shown that the use of the modified effective stress equation led to much more compatible shear strength values when comparing Consolidated-Drained (CD) and Consolidated-Undrained (CU), results, explaining the high shear strength values obtained in CU triaxial tests, even when the pore pressure is almost equal to the confining stress.

Shariatmadari, Nader, E-mail: shariatmadari@iust.ac.i [Dept. of Civil Engineering, Iran University of Science and Technology, Narmak, 16846-13114 Teharn (Iran, Islamic Republic of); Machado, Sandro Lemos, E-mail: smachado@ufba.b [Dept. of Materials Science and Technology, Federal University of Bahia, 02 Aristides Novis St., 40210-630 Salvador-BA (Brazil); Noorzad, Ali, E-mail: noorzad@pwut.ac.i [Faculty of Water Engineering, Power and Water University of Technology, Tehranpars, 1719-16765 Tehran (Iran, Islamic Republic of); Karimpour-Fard, Mehran, E-mail: karimpour_mehran@iust.ac.i [Dept. of Civil Engineering, Iran University of Science and Technology, Narmak, 16846-13114 Teharn (Iran, Islamic Republic of)

2009-12-15T23:59:59.000Z

13

Aluminum Reactions and Problems in Municipal Solid Waste Landfills  

E-Print Network (OSTI)

Aluminum Reactions and Problems in Municipal Solid Waste Landfills G. Vincent Calder, Ph.D.1 ; and Timothy D. Stark, Ph.D., P.E., F.ASCE2 Abstract: Aluminum enters municipal solid waste MSW landfills from problematic for landfill operations by generating undesirable heat, liquid leachate, and gases

14

List of Municipal Solid Waste Incentives | Open Energy Information  

Open Energy Info (EERE)

Waste Incentives Waste Incentives Jump to: navigation, search The following contains the list of 172 Municipal Solid Waste Incentives. CSV (rows 1 - 172) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active Advanced Clean Energy Project Grants (Texas) State Grant Program Texas Commercial Industrial Utility Biomass Municipal Solid Waste No Advanced Energy Fund (Ohio) Public Benefits Fund Ohio Commercial Industrial Institutional Residential Utility Biomass CHP/Cogeneration Fuel Cells Fuel Cells using Renewable Fuels Geothermal Electric Hydroelectric energy Landfill Gas Microturbines Municipal Solid Waste Photovoltaics Solar Space Heat Solar Thermal Electric Solar Water Heat Wind energy Yes Alternative Energy Law (AEL) (Iowa) Renewables Portfolio Standard Iowa Investor-Owned Utility Anaerobic Digestion

15

Aqueous alteration of municipal solid waste ash  

SciTech Connect

Municipal solid waste (MSW) ash is composed largely of amorphous oxides and approximately 20% minerals including halite, magnetite, hematite, quartz, gypsum, calcite, and rutile. It is also enriched in toxic trace metals by up to three orders of magnitude over average soil. The thermodynamic stabilities and rates of dissolution of the minerals and glasses in MSW ash will determine whether the ash is an environmental problem. The authors have used batch reactors at 20, 40, and 60 C over time periods up to 60 days to simulate longer reaction times for ash under cooler landfill conditions. Soluble salts are most quickly dissolved, giving solutions dominated by Ca[sup 2+], Na[sup +], K[sup +], SO[sub 2][sup 2[minus

Kirby, C.S.; Rimstidt, J.D. (Virginia Polytechnic Institute and State Univ., Blacksburg, VA (United States))

1992-01-01T23:59:59.000Z

16

Conversion of municipal solid waste to hydrogen  

SciTech Connect

LLNL and Texaco are cooperatively developing a physical and chemical treatment method for the conversion of municipal solid waste (MSW) to hydrogen via the steps of hydrothermal pretreatment, gasification and purification. LLNL`s focus has been on hydrothermal pretreatment of MSW in order to prepare a slurry of suitable viscosity and heating value to allow efficient and economical gasification and hydrogen production. The project has evolved along 3 parallel paths: laboratory scale experiments, pilot scale processing, and process modeling. Initial laboratory-scale MSW treatment results (e.g., viscosity, slurry solids content) over a range of temperatures and times with newspaper and plastics will be presented. Viscosity measurements have been correlated with results obtained at MRL. A hydrothermal treatment pilot facility has been rented from Texaco and is being reconfigured at LLNL; the status of that facility and plans for initial runs will be described. Several different operational scenarios have been modeled. Steady state processes have been modeled with ASPEN PLUS; consideration of steam injection in a batch mode was handled using continuous process modules. A transient model derived from a general purpose packed bed model is being developed which can examine the aspects of steam heating inside the hydrothermal reactor vessel. These models have been applied to pilot and commercial scale scenarios as a function of MSW input parameters and have been used to outline initial overall economic trends. Part of the modeling, an overview of the MSW gasification process and the modeling of the MSW as a process material, was completed by a DOE SERS (Science and Engineering Research Semester) student. The ultimate programmatic goal is the technical demonstration of the gasification of MSW to hydrogen at the laboratory and pilot scale and the economic analysis of the commercial feasibility of such a process.

Richardson, J.H.; Rogers, R.S.; Thorsness, C.B. [and others

1995-04-01T23:59:59.000Z

17

Mercury emissions from municipal solid waste combustors  

SciTech Connect

This report examines emissions of mercury (Hg) from municipal solid waste (MSW) combustion in the United States (US). It is projected that total annual nationwide MSW combustor emissions of mercury could decrease from about 97 tonnes (1989 baseline uncontrolled emissions) to less than about 4 tonnes in the year 2000. This represents approximately a 95 percent reduction in the amount of mercury emitted from combusted MSW compared to the 1989 mercury emissions baseline. The likelihood that routinely achievable mercury emissions removal efficiencies of about 80 percent or more can be assured; it is estimated that MSW combustors in the US could prove to be a comparatively minor source of mercury emissions after about 1995. This forecast assumes that diligent measures to control mercury emissions, such as via use of supplemental control technologies (e.g., carbon adsorption), are generally employed at that time. However, no present consensus was found that such emissions control measures can be implemented industry-wide in the US within this time frame. Although the availability of technology is apparently not a limiting factor, practical implementation of necessary control technology may be limited by administrative constraints and other considerations (e.g., planning, budgeting, regulatory compliance requirements, etc.). These projections assume that: (a) about 80 percent mercury emissions reduction control efficiency is achieved with air pollution control equipment likely to be employed by that time; (b) most cylinder-shaped mercury-zinc (CSMZ) batteries used in hospital applications can be prevented from being disposed into the MSW stream or are replaced with alternative batteries that do not contain mercury; and (c) either the amount of mercury used in fluorescent lamps is decreased to an industry-wide average of about 27 milligrams of mercury per lamp or extensive diversion from the MSW stream of fluorescent lamps that contain mercury is accomplished.

Not Available

1993-05-01T23:59:59.000Z

18

Comprehensive Municipal Solid Waste Management, Resource Recovery, and Conservation Act (Texas)  

Energy.gov (U.S. Department of Energy (DOE))

This Act encourages the establishment of regional waste management facilities and the cooperation of local waste management entities in order to streamline the management of municipal solid waste...

19

A legislator`s guide to municipal solid waste management  

SciTech Connect

The purpose of this guide is to allow individual state legislators to gain a better understanding of municipal solid waste (MSW) management issues in general, and examine the applicability of these concerns to their state. This guide incorporates a discussion of MSW management issues and a comprehensive overview of the components of an integrated solid waste management system. Major MSW topics discussed include current management issues affecting states, federal activities, and state laws and local activities. Solid waste characteristics and management approaches are also detailed.

Starkey, D.; Hill, K.

1996-08-01T23:59:59.000Z

20

Municipal solid waste characteristics and management in Allahabad, India  

E-Print Network (OSTI)

by political, legal, socio-cultural, environmental and economic factors, as well as available resources on a suitable management plan (Shimura et al., 2001). More than 90% of MSW in India is directly disposedMunicipal solid waste characteristics and management in Allahabad, India Mufeed Sharholy a , Kafeel

Columbia University

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Data summary of municipal solid waste management alternatives  

SciTech Connect

This appendix contains the numerically indexed bibliography for the complete group of reports on municipal solid waste management alternatives. The list references information on the following topics: mass burn technologies, RDF technologies, fluidized bed combustion, pyrolysis and gasification of MSW, materials recovery- recycling technologies, sanitary landfills, composting and anaerobic digestion of MSW.

Not Available

1992-10-01T23:59:59.000Z

22

Seismic Response Analysis of Municipal Solid Waste Landfill  

Science Journals Connector (OSTI)

According to the engineering practice of municipal solid waste landfill, the dynamic response of landfill based on the finite element method is implemented. The equivalent linearization method is used to consider the non-linear dynamic response characteristics. ... Keywords: Dynamic response, Ground motion input, Finite element method

Zhang Guodong; Li Yong; Jin Xing; Li Rongbin; Chen Fei

2009-10-01T23:59:59.000Z

23

Data summary of municipal solid waste management alternatives  

SciTech Connect

This appendix contains background information, technical descriptions, economic data, mass and energy balances, and information on environmental releases for the refuse derived fuels (RDF) option in municipal solid waste management alternatives. Demonstration programs at St. Louis, Missouri; Franklin, Ohio; and Delaware are discussed. Information on pellet production and cofiring with coal is also presented.

Not Available

1992-10-01T23:59:59.000Z

24

The Municipal Solid Waste Landfill as a Source of Montreal Protocol-restricted Halocarbons in the  

E-Print Network (OSTI)

The Municipal Solid Waste Landfill as a Source of Montreal Protocol-restricted Halocarbons of Geophysics #12;2 #12;The Municipal Solid Waste Landfill as a Source of Montreal Protocol municipal solid waste (MSW) landfills. With several hundred MSW landfills in both the US and UK, estimating

25

Effects of biodrying process on municipal solid waste properties  

Science Journals Connector (OSTI)

In this paper, the effect of biodrying process on municipal solid waste (MSW) properties was studied. The results obtained indicated that after 14 d, biodrying reduced the water content of waste, allowing the production of biodried waste with a net heating value (NHV) of 16,779 ± 2,074 kJ kg?1 wet weight, i.e. 41% higher than that of untreated waste. The low moisture content of the biodried material reduced, also, the potential impacts of the waste, i.e. potential self-ignition and potential odors production. Low waste impacts suggest to landfill the biodried material obtaining energy via biogas production by waste re-moistening, i.e. bioreactor. Nevertheless, results of this work indicate that biodrying process because of the partial degradation of the organic fraction contained in the waste (losses of 290 g kg?1 VS), reduced of about 28% the total producible biogas.

F. Tambone; B. Scaglia; S. Scotti; F. Adani

2011-01-01T23:59:59.000Z

26

Gaseous emissions during concurrent combustion of biomass and non-recyclable municipal solid waste  

Science Journals Connector (OSTI)

Biomass and municipal solid waste offer sustainable sources ... form of combined cooling, heat and power. Combustion of biomass has a lesser impact than solid fossil ... an integrated, sustainable waste managemen...

René Laryea-Goldsmith; John Oakey; Nigel J Simms

2011-02-01T23:59:59.000Z

27

Data summary of municipal solid waste management alternatives  

SciTech Connect

This appendix provides information on fluidized-bed combustion (FBC) technology as it has been applied to municipal waste combustion (MWC). A review of the literature was conducted to determine: (1) to what extent FBC technology has been applied to MWC, in terms of number and size of units was well as technology configuration; (2) the operating history of facilities employing FBC technology; and (3) the cost of these facilities as compared to conventional MSW installations. Where available in the literature, data on operating and performance characteristics are presented. Tabular comparisons of facility operating/cost data and emissions data have been complied and are presented. The literature review shows that FBC technology shows considerable promise in terms of providing improvements over conventional technology in areas such as NOx and acid gas control, and ash leachability. In addition, the most likely configuration to be applied to the first large scale FBC dedicated to municipal solid waste (MSW) will employ circulating bed (CFB) technology. Projected capital costs for the Robbins, Illinois 1600 ton per day CFB-based waste-to-energy facility are competitive with conventional systems, in the range of $125,000 per ton per day of MSW receiving capacity.

Not Available

1992-10-01T23:59:59.000Z

28

Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume 1: Availability of Feedstock and Technology  

Energy.gov (U.S. Department of Energy (DOE))

Municipal solid waste (MSW) is a domestic energy resource with the potential to provide a significant amount of energy to meet US liquid fuel requirements. MSW is defined as household waste, commercial solid waste, nonhazardous sludge, conditionally exempt, small quantity hazardous waste, and industrial solid waste. It includes food waste, residential rubbish, commercial and industrial wastes, and construction and demolition debris. It has an average higher heating value (HHV) of approximately 5100 btu/lb (as arrived basis).

29

Sepiolite as an Alternative Liner Material in Municipal Solid Waste Landfills  

E-Print Network (OSTI)

Sepiolite as an Alternative Liner Material in Municipal Solid Waste Landfills Yucel Guney1 ; Savas in municipal solid waste landfills. However, natural clays may not always provide good contaminant sorption necessitates addition of kaolinite before being used as a landfill material. The valence of the salt solutions

Aydilek, Ahmet

30

Composition of Municipal Solid Waste-Need for Thermal Treatment in the present Indian context  

E-Print Network (OSTI)

Composition of Municipal Solid Waste- Need for Thermal Treatment in the present Indian context of estimating heat value of municipal wastes, from the view point of assessing the waste's amenability for thermal treatment in the Indian context at the present juncture. The paper also seeks to reason out

Columbia University

31

Process modeling of hydrogen production from municipal solid waste  

SciTech Connect

The ASPEN PLUS commercial simulation software has been used to develop a process model for a conceptual process to convert municipal solid waste (MSW) to hydrogen. The process consists of hydrothermal treatment of the MSW in water to create a slurry suitable as feedstock for an oxygen blown Texaco gasifier. A method of reducing the complicated MSW feed material to a manageable set of components is outlined along with a framework for modeling the stoichiometric changes associated with the hydrothermal treatment process. Model results indicate that 0.672 kmol/s of hydrogen can be produced from the processing of 30 kg/s (2600 tonne/day) of raw MSW. A number of variations on the basic processing parameters are explored and indicate that there is a clear incentive to reduce the inert fraction in the processed slurry feed and that cofeeding a low value heavy oil may be economically attractive.

Thorsness, C.B.

1995-01-01T23:59:59.000Z

32

Long-term behavior of municipal solid waste landfills  

Science Journals Connector (OSTI)

A method is presented to predict the long-term behavior of element concentrations (non-metals and metals) in the leachate of a municipal solid waste (MSW) landfill. It is based on water flux and concentration measurements in leachates over one year, analysis of drilled cores from MSW landfills and leaching experiments with these samples. A mathematical model is developed to predict the further evolution of annual flux-weighted mean element concentrations in leachates after the “intensive reactor phase”, i.e. after the gas production has dropped to a very low level. The results show that the organic components are the most important substances to control until the leachate is compatible with the environment. This state of low emissions, the so-called “final storage quality”, will take many centuries to be achieved in a moderate climate.

H. Belevi; P. Baccini

1989-01-01T23:59:59.000Z

33

Integrated municipal solid waste scenario model using advanced pretreatment and waste to energy processes  

Science Journals Connector (OSTI)

Abstract In this paper an Integrated Municipal Solid Waste scenario model (IMSW-SM) with a potential practical application in the waste management sector is analyzed. The model takes into account quantification and characterization of Municipal Solid Waste (MSW) streams from different sources, selective collection (SC), advanced mechanical sorting, material recovery and advanced thermal treatment. The paper provides a unique chain of advanced waste pretreatment stages of fully commingled waste streams, leading to an original set of suggestions and future contributions to a sustainable IMSWS, taking into account real data and EU principles. The selection of the input data was made on MSW management real case studies from two European regions. Four scenarios were developed varying mainly SC strategies and thermal treatment options. The results offer useful directions for decision makers in order to calibrate modern strategies in different realities.

Gabriela Ionescu; Elena Cristina Rada; Marco Ragazzi; Cosmin M?rculescu; Adrian Badea; Tiberiu Apostol

2013-01-01T23:59:59.000Z

34

Hydrogen production by gasification of municipal solid waste  

SciTech Connect

As fossil fuel reserves run lower and lower, and as their continued widespread use leads toward numerous environmental problems, the need for clean and sustainable energy alternatives becomes ever clearer. Hydrogen fuel holds promise as such as energy source, as it burns cleanly and can be extracted from a number of renewable materials such as municipal solid waste (MSW), which can be considered largely renewable because of its high content of paper and biomass-derived products. A computer model is being developed using ASPEN Plus flow sheeting software to simulate a process which produces hydrogen gas from MSW; the model will later be used in studying the economics of this process and is based on an actual Texaco coal gasification plant design. This paper gives an overview of the complete MSW gasification process, and describes in detail the way in which MSW is modeled by the computer as a process material. In addition, details of the gasifier unit model are described; in this unit modified MSW reacts under pressure with oxygen and steam to form a mixture of gases which include hydrogen.

Rogers, R. III

1994-05-20T23:59:59.000Z

35

Data summary of municipal solid waste management alternatives  

SciTech Connect

This appendix contains the alphabetically indexed bibliography for the complete group of reports on municipal waste management alternatives. The references are listed for each of the following topics: mass burn technologies, RDF technologies, fluidized-bed combustion, pyrolysis and gasification of MSW, materials recovery- recycling technologies, sanitary landfills, composting, and anaerobic digestion of MSW.

Not Available

1992-10-01T23:59:59.000Z

36

Pyrolysis of Municipal Solid Waste for Syngas Production by Microwave Irradiation  

Science Journals Connector (OSTI)

In the present study, we discuss the application of microwave-irradiated pyrolysis of municipal solid waste (MSW) for total recovery of useful gases and energy. The MSW pyrolysis under microwave irradiation hi...

Vidyadhar V. Gedam; Iyyaswami Regupathi

2012-03-01T23:59:59.000Z

37

Integrated facility for municipal solid waste disposal, electrical generation, and desalination. Master`s thesis  

SciTech Connect

A preliminary design was completed for a facility that uses municipal solid waste as fuel for generating electricity and cogeneration steam for a seawater desalination unit. An average city of 100,000 population is the basis of the design. The design showed that heat from the combustion of municipal solid waste will provide nearly 2% of per capita electrical power needs and 7% of fresh water requirements. This thesis proposes a new arrangement of known technologies for use in Public Works.

Hanby, G.F.

1995-12-31T23:59:59.000Z

38

Characterization of Landfill Gas Composition at the Fresh Kills Municipal Solid-Waste Landfill  

Science Journals Connector (OSTI)

Characterization of Landfill Gas Composition at the Fresh Kills Municipal Solid-Waste Landfill ... The most common disposal method in the United States for municipal solid waste (MSW) is burial in landfills. ... Under the New Source Performance Standards and Emission Guidelines for MSW landfills, MSW operators are required to determine the nonmethane organic gas generation rate of their landfill through modeling and/or measurements. ...

Bart Eklund; Eric P. Anderson; Barry L. Walker; Don B. Burrows

1998-06-18T23:59:59.000Z

39

A new technique to monitor ground-water quality at municipal solid waste landfills  

E-Print Network (OSTI)

A NEW TECHNIQUE TO MONITOR GROUND-WATER EQUALITY AT MUNICIPAL SOLID WASTE LANDFILLS A Thesis by STEVEN CHARLES HART Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE May 1989 Major Subject: Geology A NEW TECHNIIIUE TO MONITOR GROUND-WATER IIUALITY AT MUNICIPAL SOLID WASTE LANDFILLS A Thesis by STEVEN CHARLES HART Approved as to style and content by: Christo her C. Mathewson (Chair...

Hart, Steven Charles

2012-06-07T23:59:59.000Z

40

Solid waste disposal options: an optimum disposal model for the management of municipal solid waste  

E-Print Network (OSTI)

and compostable material was generally burned in backyards. In 1970, the Clean Air Act was passed restricting the burning of leaves and other yard waste. ' These wastes were then disposed in landfills. As landfills reached capacity, commu- nities composted... separation pro- grams because of their "throw-away" mentality. " ~ln in r ttgtt Incineration is the controlled burning of the combustible fraction of solid waste. The first electrical generating station in the United States that was fueled by solid waste...

Haney, Brenda Ann

2012-06-07T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Reconsidering Municipal Solid Waste as a Renewable Energy Feedstock For many years, opposition to the use of municipal solid waste (MSW) as an energy resource has been nearly universal among  

E-Print Network (OSTI)

Reconsidering Municipal Solid Waste as a Renewable Energy Feedstock July 2009 For many years, opposition to the use of municipal solid waste (MSW) as an energy resource has been nearly universal among of technologies can be used to create energy from MSW: · Landfill Gas Capture -- Waste in landfills naturally

Columbia University

42

Generation!and!Disposition!of!Municipal!Solid!Waste! (MSW)!in!the!United!States!A!National!Survey!  

E-Print Network (OSTI)

! 1! ! Generation!and!Disposition!of!Municipal!Solid!Waste! (MSW on Municipal Solid Waste (MSW) Generation and Disposition in the U.S., in collaboration with Ms. Nora Goldstein was not carried out in 2012 and in 2013 EEC and BioCycle agreed that the 2013 Survey of Waste Generation

Columbia University

43

'Incineration: A burning issue or a load of rubbish?’ Examining public attitudes to municipal solid waste incineration.  

E-Print Network (OSTI)

??The author set out to investigate public attitudes to municipal solid waste (MSW) incineration. The area chosen for the study was Carlow town, a regional… (more)

Dillon, Rachel

2006-01-01T23:59:59.000Z

44

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics  

Science Journals Connector (OSTI)

Abstract Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in higher heating value. Analysis of the post-processing water uptake and compressive strength showed a correlation between density and stability to both mechanical stress and humid environment. Proximate analysis indicated heating values comparable to coal. The results showed that mechanical and moisture uptake stability were improved when the moisture and air contents were optimized. Moreover, the briquette sample composition was similar to biomass fuels but had significant advantages due to addition of waste plastics that have high energy content compared to other waste types. Addition of PP and HDPE presented better benefits than addition of PET due to lower softening temperature and lower oxygen content. It should be noted that while harmful emissions such as dioxins, furans and mercury can result from burning plastics, WTE facilities have been able to control these emissions to meet US EPA standards. This research provides a drop-in coal replacement that reduces demand on landfill space and replaces a significant fraction of fossil-derived fuel with a renewable alternative.

JeongIn Gug; David Cacciola; Margaret J. Sobkowicz

2014-01-01T23:59:59.000Z

45

The potential of GHG emission savings for programmatic CDM by municipal solid waste composting in the Western Province - Sri Lanka  

Science Journals Connector (OSTI)

The Western Province (WP) of Sri Lanka, as the most populated province in the country is burdened with a high level of municipal solid waste generation. Out of the 48 administrative local authorities within the WP, only 16 local authorities are practicing municipal solid waste composting. All other local authorities are practicing the most common method of MSW disposal; open dumping. The study was aimed at finding the potential of green house gas emission savings by municipal solid waste composting according to Programmatic Clean Development Mechanism in 32 local authorities of the WP which are not currently practicing MSW composting in order to quantify the certified emission reduction. The daily collection rate of municipal solid waste in the entire WP is around 2,000 tons per day. Biodegradable portion dominates the bulk of municipal solid waste in WP as about 76.30%. There is potential of claiming 231 certified emission reductions annually with regard to MSW composting within the WP.

V.K.D.H. Kariyakarawana; N.J.G.J. Bandara; S. Leelarathne

2014-01-01T23:59:59.000Z

46

Process and technological aspects of municipal solid waste gasification. A review  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Critical assessment of the main commercially available MSW gasifiers. Black-Right-Pointing-Pointer Detailed discussion of the basic features of gasification process. Black-Right-Pointing-Pointer Description of configurations of gasification-based waste-to-energy units. Black-Right-Pointing-Pointer Environmental performance analysis, on the basis of independent sources data. - Abstract: The paper proposes a critical assessment of municipal solid waste gasification today, starting from basic aspects of the process (process types and steps, operating and performance parameters) and arriving to a comparative analysis of the reactors (fixed bed, fluidized bed, entrained bed, vertical shaft, moving grate furnace, rotary kiln, plasma reactor) as well as of the possible plant configurations (heat gasifier and power gasifier) and the environmental performances of the main commercially available gasifiers for municipal solid wastes. The analysis indicates that gasification is a technically viable option for the solid waste conversion, including residual waste from separate collection of municipal solid waste. It is able to meet existing emission limits and can have a remarkable effect on reduction of landfill disposal option.

Arena, Umberto, E-mail: umberto.arena@unina2.it [Department of Environmental Sciences, Second University of Naples, Via A. Vivaldi, 43, 81100 Caserta (Italy)

2012-04-15T23:59:59.000Z

47

Combustion of municipal solid wastes with oil shale in a circulating fluidized bed. Final report  

SciTech Connect

The problem addressed by our invention is that of municipal solid waste utilization. The dimensions of the problem can be visualized by the common comparison that the average individual in America creates in five years time an amount of solid waste equivalent in weight to the Statue of Liberty. The combustible portion of the more than 11 billion tons of solid waste (including municipal solid waste) produced in the United States each year, if converted into useful energy, could provide 32 quads per year of badly needed domestic energy, or more than one-third of our annual energy consumption. Conversion efficiency and many other factors make such a production level unrealistic, but it is clear that we are dealing with a very significant potential resource. This report describes research pertaining to the co-combustion of oil shale with solid municipal wastes in a circulating fluidized bed. The oil shale adds significant fuel content and also constituents that can possible produce a useful cementitious ash.

NONE

1996-06-30T23:59:59.000Z

48

Data summary of municipal solid waste management alternatives. Volume 12, Numerically indexed bibliography  

SciTech Connect

This appendix contains the numerically indexed bibliography for the complete group of reports on municipal solid waste management alternatives. The list references information on the following topics: mass burn technologies, RDF technologies, fluidized bed combustion, pyrolysis and gasification of MSW, materials recovery- recycling technologies, sanitary landfills, composting and anaerobic digestion of MSW.

none,

1992-10-01T23:59:59.000Z

49

2014 ENERGY AND ECONOMIC VALUE OF MUNICIPAL SOLID WASTE (MSW), INCLUDING NON-RECYCLED PLASTICS (NRP),  

E-Print Network (OSTI)

-to-energy (WTE) plants, 0.27 million tons (0.7%) were used as alternative fuel in cement production, and 32 Earth Engineering Center (EEC) Report to the American Chemistry Council (ACC) which was based on U.S. 2008 data and quantified the energy and economic value of municipal solid wastes (MSW) and non

Columbia University

50

Data summary of municipal solid waste management alternatives. Volume 4, Appendix B: RDF technologies  

SciTech Connect

This appendix contains background information, technical descriptions, economic data, mass and energy balances, and information on environmental releases for the refuse derived fuels (RDF) option in municipal solid waste management alternatives. Demonstration programs at St. Louis, Missouri; Franklin, Ohio; and Delaware are discussed. Information on pellet production and cofiring with coal is also presented.

none,

1992-10-01T23:59:59.000Z

51

Patterns in Trash: Factors that Drive Municipal Solid Waste Recycling.  

E-Print Network (OSTI)

??Municipal recycling is driven by a variety of factors. Yet how these factors change over time is not well understood. I analyze a suite of… (more)

Starr, Jared

2014-01-01T23:59:59.000Z

52

A Study of Gasification of Municipal Solid Waste Using a Double Inverse Diffusion Flame Burner  

Science Journals Connector (OSTI)

A Study of Gasification of Municipal Solid Waste Using a Double Inverse Diffusion Flame Burner ... Furthermore, the experiences of the waste incineration industry driven in the past by regulatory as well as technical issues may facilitate their commercial potentials outside the common market, especially in highly populated developing countries such as Korea with scarce landfill sites. ... Recently, several new technologies that involve gasification or combinations of pyrolysis, combustion, and gasification processes are currently being brought into the market for energy-efficient, environmentally friendly and economically sound methods of thermal processing of wastes. ...

Tae-Heon Kwak; Seungmoon Lee; Sanjeev Maken; Ho-Chul Shin; Jin-Won Park; Young Done Yoo

2005-08-24T23:59:59.000Z

53

Seasonal characterization of municipal solid waste (MSW) in the city of Chihuahua, Mexico  

Science Journals Connector (OSTI)

Management of municipal solid waste (MSW) has become a significant environmental problem, especially in fast-growing cities. The amount of waste generated increases each year and this makes it difficult to create solutions which due to the increase in waste generation year after year and having to identify a solution that will have minimum impact on the environment. To determine the most sustainable waste management strategy for Chihuahua, it is first necessary to identify the nature and composition of the city’s urban waste. The MSW composition varied considerably depending on many factors, the time of year is one of them. Therefore, as part of our attempt to implement an integral waste management system in the city of Chihuahua, we conducted a study of the characteristics of MSW composition for the different seasons. This paper analyzes and compares the findings of the study of the characterization and the generation of solid waste from households at three different socio-economic levels in the city over three periods (April and August, 2006 and January, 2007). The average weight of waste generated in Chihuahua, taking into account all three seasons, was 0.592 kg capita?1 day?1. Our results show that the lowest income groups generated the least amount of waste. We also found that less waste was generated during the winter season. The breakdown for the composition of the waste shows that organic waste accounts for the largest proportion (45%), followed by paper (17%) and others (16%).

Guadalupe Gómez; Montserrat Meneses; Lourdes Ballinas; Francesc Castells

2009-01-01T23:59:59.000Z

54

Seasonal characterization of municipal solid waste (MSW) in the city of Chihuahua, Mexico  

SciTech Connect

Management of municipal solid waste (MSW) has become a significant environmental problem, especially in fast-growing cities. The amount of waste generated increases each year and this makes it difficult to create solutions which due to the increase in waste generation year after year and having to identify a solution that will have minimum impact on the environment. To determine the most sustainable waste management strategy for Chihuahua, it is first necessary to identify the nature and composition of the city's urban waste. The MSW composition varied considerably depending on many factors, the time of year is one of them. Therefore, as part of our attempt to implement an integral waste management system in the city of Chihuahua, we conducted a study of the characteristics of MSW composition for the different seasons. This paper analyzes and compares the findings of the study of the characterization and the generation of solid waste from households at three different socio-economic levels in the city over three periods (April and August, 2006 and January, 2007). The average weight of waste generated in Chihuahua, taking into account all three seasons, was 0.592 kg capita{sup -1} day{sup -1}. Our results show that the lowest income groups generated the least amount of waste. We also found that less waste was generated during the winter season. The breakdown for the composition of the waste shows that organic waste accounts for the largest proportion (45%), followed by paper (17%) and others (16%)

Gomez, Guadalupe [Departament d'Enginyeria Quimica, Universitat Rovira i Virgili, 43007 Tarragona (Spain); Facultad de Ciencias Quimicas, Universidad Autonoma de Chihuahua, 31310 (Mexico); Meneses, Montserrat [Departament d'Enginyeria Quimica, Universitat Rovira i Virgili, 43007 Tarragona (Spain); Ballinas, Lourdes [Facultad de Ciencias Quimicas, Universidad Autonoma de Chihuahua, 31310 (Mexico); Castells, Francesc [Departament d'Enginyeria Quimica, Universitat Rovira i Virgili, 43007 Tarragona (Spain)], E-mail: francesc.castells@urv.cat

2009-07-15T23:59:59.000Z

55

Haraldrud Municipal Solid Waste Combustion Plant in Oslo.  

E-Print Network (OSTI)

??This thesis has studied Haraldrud MSW combustion process. Haraldrud is a realcombustion plant burning waste for citizens of Oslo. A thoroughly description ofthe combustion process… (more)

Gudim, Simen Johan

2011-01-01T23:59:59.000Z

56

Cellulosic materials recovered from steam classified municipal solid wastes as feedstocks for conversion to fuels and chemicals  

Science Journals Connector (OSTI)

A process has been developed for the treatment of municipal solid waste to separate and recover the cellulosic biomass from the nonbiomass components. ... highly suitable as a feedstock for conversion to fuel, fe...

Michael H. Eley; Gerald R. Guinn; Joyita Bagchi

1995-09-01T23:59:59.000Z

57

Municipal solid waste degradation and landfill gas resources characteristics in self-recirculating sequencing batch bioreactor landfill  

Science Journals Connector (OSTI)

Based on the degradation characteristics of municipal solid waste (MSW) in China, the traditional anaerobic sequencing batch bioreactor landfill (ASBRL) was optimized, and an improved anaerobic sequencing batch b...

Xiao-zhi Zhou ???; Shu-xun Sang ???; Li-wen Cao ???

2012-12-01T23:59:59.000Z

58

Data summary of municipal solid waste management alternatives. Volume 3, Appendix A: Mass burn technologies  

SciTech Connect

This appendix on Mass Burn Technologies is the first in a series designed to identify, describe and assess the suitability of several currently or potentially available generic technologies for the management of municipal solid waste (MSW). These appendices, which cover eight core thermoconversion, bioconversion and recycling technologies, reflect public domain information gathered from many sources. Representative sources include: professional journal articles, conference proceedings, selected municipality solid waste management plans and subscription technology data bases. The information presented is intended to serve as background information that will facilitate the preparation of the technoeconomic and life cycle mass, energy and environmental analyses that are being developed for each of the technologies. Mass burn has been and continues to be the predominant technology in Europe for the management of MSW. In the United States, the majority of the existing waste-to-energy projects utilize this technology and nearly 90 percent of all currently planned facilities have selected mass burn systems. Mass burning generally refers to the direct feeding and combustion of municipal solid waste in a furnace without any significant waste preprocessing. The only materials typically removed from the waste stream prior to combustion are large bulky objects and potentially hazardous or undesirable wastes. The technology has evolved over the last 100 or so years from simple incineration to the most highly developed and commercially proven process available for both reducing the volume of MSW and for recovering energy in the forms of steam and electricity. In general, mass burn plants are considered to operate reliably with high availability.

none,

1992-10-01T23:59:59.000Z

59

Generation!and!Disposition!of!Municipal!Solid!Waste! (MSW)!in!the!United!States!A!National!Survey!  

E-Print Network (OSTI)

! 1! ! Generation!and!Disposition!of!Municipal!Solid!Waste! (MSW Waste (MSW) Generation and Disposition in the U.S., in collaboration with Ms. Nora Goldstein of Bio in 2012 and in 2013 EEC and BioCycle agreed that the 2013 Survey of Waste Generation and Disposition

60

Plasmatron gasification of biomass lignocellulosic waste materials derived from municipal solid waste  

Science Journals Connector (OSTI)

Abstract The aim of this work is to study the feasibility and operational performance of plasmatron (plasma torch) gasification of municipal solid waste mixed with raw wood (MSW/RW) derived from the pretreatment of Steam Mechanical Heat Treatment (SMHT), as the target material (MRM). A 10 kW plasmatron reactor is used for gasification of the MRM. The production of syngas (CO and H2) is the major component, and almost 90% of the gaseous products appear in 2 min of reaction time, with relatively high reaction rates. The syngas yield is between 88.59 and 91.84 vol%, and the recovery mass ratio of syngas from MRM is 45.19 down to 27.18 wt% with and without steam with the energy yields of 59.07–111.89%. The concentrations of gaseous products from the continuous feeding of 200 g/h are stable and higher than the average concentrations of the batch feeding of 10 g. The residue from the plasmatron gasification with steam is between 0 and 4.52 wt%, with the inorganic components converted into non-leachable vitrified lava, which is non-hazardous. The steam methane reforming reaction, hydrogasification reaction and Boudouard reaction all contribute to the increase in the syngas yield. It is proved that MSW can be completely converted into bioenergy using SMHT, followed by plasmatron gasification.

Je-Lueng Shie; Li-Xun Chen; Kae-Long Lin; Ching-Yuan Chang

2014-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Recovery of solid fuel from municipal solid waste by hydrothermal treatment using subcritical water  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Hydrothermal treatment using subcritical water was studied to recover solid fuel from MSW. Black-Right-Pointing-Pointer More than 75% of carbon in MSW was recovered as char. Black-Right-Pointing-Pointer Heating value of char was comparable to that of brown coal and lignite. Black-Right-Pointing-Pointer Polyvinyl chloride was decomposed at 295 Degree-Sign C and 8 MPa and was removed by washing. - Abstract: Hydrothermal treatments using subcritical water (HTSW) such as that at 234 Degree-Sign C and 3 MPa (LT condition) and 295 Degree-Sign C and 8 MPa (HT condition) were investigated to recover solid fuel from municipal solid waste (MSW). Printing paper, dog food (DF), wooden chopsticks, and mixed plastic film and sheets of polyethylene, polypropylene, and polystyrene were prepared as model MSW components, in which polyvinylchloride (PVC) powder and sodium chloride were used to simulate Cl sources. While more than 75% of carbon in paper, DF, and wood was recovered as char under both LT and HT conditions, plastics did not degrade under either LT or HT conditions. The heating value (HV) of obtained char was 13,886-27,544 kJ/kg and was comparable to that of brown coal and lignite. Higher formation of fixed carbon and greater oxygen dissociation during HTSW were thought to improve the HV of char. Cl atoms added as PVC powder and sodium chloride to raw material remained in char after HTSW. However, most Cl originating from PVC was found to converse into soluble Cl compounds during HTSW under the HT condition and could be removed by washing. From these results, the merit of HTSW as a method of recovering solid fuel from MSW is considered to produce char with minimal carbon loss without a drying process prior to HTSW. In addition, Cl originating from PVC decomposes into soluble Cl compound under the HT condition. The combination of HTSW under the HT condition and char washing might improve the quality of char as alternative fuel.

Hwang, In-Hee, E-mail: hwang@eng.hokudai.ac.jp [Laboratory of Solid Waste Disposal Engineering, Faculty of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060 8628 (Japan); Aoyama, Hiroya; Matsuto, Toshihiko; Nakagishi, Tatsuhiro; Matsuo, Takayuki [Laboratory of Solid Waste Disposal Engineering, Faculty of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060 8628 (Japan)

2012-03-15T23:59:59.000Z

62

Municipal solid waste energy conversion study on Guam and American Samoa  

SciTech Connect

In the Pacific Islands of Guam and Tutuila in American Samoa, conversion of municipal solid waste to useable energy forms - principally electricity but possibly steam - may hold promise for reducing economic dependence on imported petroleum. A secondary benefit may be derived from reduction of solid waste landfill requirements. At the preliminary planning stage, waste-to-energy facilities producing electricity appear technically and environmentally feasible. Economically, the projects appear marginal but could be viable under specific conditions related to capital costs, revenue from garbage collection and revenue from the sale of the energy generated. Grant funding for the projects would considerably enhance the economic viability of the proposed facilities. The projects appear sufficiently viable to proceed to the detailed planning stage. Such projects are not viable for the islands now emerging from the US Trust Territory of the Pacific Islands.

Not Available

1984-03-31T23:59:59.000Z

63

Multiple regression analysis for the estimation of energy content of municipal solid waste  

Science Journals Connector (OSTI)

A regression equation is proposed to predict the Higher Heating Value (HHV) of Municipal Solid Waste (MSW) from the waste data of 86 cities of 35 countries. A mathematical model is developed, by using Statistical Package for Social Sciences (SPSS-10.0), to correlate the energy content of waste with the variables derived from its physical composition. Performance of the proposed multiple regression model is superior to available models. For validation, the proposed model is applied to the waste data of Jaipur City (India), nine cities of EEC countries and also to the MSW of USA. Energy content values obtained by proposed regression model and Modified Dulong's Equation (MDE) are closer to the measured mean energy content values for EEC countries compared to the values obtained by Khan's method. Objective of the paper is to propose a simple model, which can replace the lengthy MDE and which has universal applicability for the predication of HHVs.

G.D. Agrawal; A.P.S. Rathore; A.B. Gupta

2007-01-01T23:59:59.000Z

64

Stabilisation of biodried municipal solid waste fine fraction in landfill bioreactor  

Science Journals Connector (OSTI)

The biodrying process of solid waste is a pre-treatment for the bio-stabilisation of the municipal solid waste. This study aims to investigate the fate of the municipal solid waste fine fraction (MSWFF) resulting from a biodrying treatment when disposed in landfills that are operated as bioreactors. Biodried MSWFF was apparently stable due to its low moisture content that slows down the microbial activity. The lab-scale anaerobic bioreactors demonstrated that a proper moisture content leads to a complete biodegradation of the organic matter contained in the biodried MSWFF. Using a pilot-scale landfill bioreactor (LBR), MSWFF stabilisation was achieved, suggesting that the leachate recirculation could be an effective approach to accomplish the anaerobic biodegradation and biostabilisation of biodried MSWFF after landfilling. The biostabilisation of the material resulting from the LBR treatment was confirmed using anaerobic and aerobic stability indices. All anaerobic and aerobic indices showed a stability increase of approximately 80% of the MSWFF after treatment in the LBR. The similar values of OD7 and BMP stability indices well agree with the relationship between the aerobic and anaerobic indices reported in literature.

Selene Grilli; Andrea Giordano; Alessandro Spagni

2012-01-01T23:59:59.000Z

65

Emissions of unintentional persistent organic pollutants from open burning of municipal solid waste from developing countries  

Science Journals Connector (OSTI)

Open burning of waste is the most significant source of polychlorinated dibenzo-para-dioxins and dibenzofurans (PCDD/PCDF) in many national inventories prepared pursuant to the Stockholm Convention on Persistent Organic Pollutants. This is particularly true for developing countries. Emission factors for \\{POPs\\} such as PCDD/PCDF, dioxin-like polychlorinated biphenyls (dl-PCB) and penta- and hexachlorobenzenes (PeCBz/HCB) from open burning of municipal solid waste in China and Mexico are reported herein. Six different waste sources were studied varying from urban-industrial to semi-urban to rural. For PCDD/PCDF, the emission factors to air ranged from 3.0 to 650 ng TEQ kg?1 waste and for dl-PCB from 0.092 to 54 ng TEQ kg?1 waste. Emission factors for PeCBz (17–1200 ng kg?1 waste) and HCB (24–1300 ng kg?1 waste) spanned a wide but similar range. Within the datasets there is no indication of significant waste composition effect on emission factor with the exception of significantly higher Mexico rural samples.

Tingting Zhang; Heidelore Fiedler; Gang Yu; Gustavo Solorzano Ochoa; William F. Carroll Jr.; Brian K. Gullett; Stellan Marklund; Abderrahmane Touati

2011-01-01T23:59:59.000Z

66

Strategies for continuous monitoring of hydrogen chloride emissions from municipal solid-waste incinerators  

SciTech Connect

The paper presents a discussion of sampling and analytical techniques for continuous monitoring of hydrogen chloride (HCl) emissions from incineration sources. The discussion focuses on commercially available systems for sample conditioning and measurement. Six HCl continuous-emission monitors were evaluated at a municipal facility for solid-waste incineration. Field-test results indicate that several techniques for continuous monitoring of HCl concentrations are available. Most of the analyzers tested, regardless of the detection or calibration techniques, indicated the same trend in the effluent HCl concentrations and produced data that was in good agreement with wet-chemistry results.

Jernigan, J.R.; Shanklin, S.; Rollins, R.; Logan, T.J.; Midgett, M.R.

1988-04-01T23:59:59.000Z

67

Evaluation of a sequential aerobicâ??anaerobic treatment of municipal solid waste in a bioreactor landfill  

Science Journals Connector (OSTI)

A sequential aerobic-anaerobic bioreactor landfill was operated and monitored over a period of 184 days. The bioreactor was filled with 120 kg of organic fraction of Municipal Solid Waste. Leachate recirculation was applied. The results showed rapid degradation of organic matter with rapid settlement during the aerobic period. The initial COD and BOD5 were reduced from 46,500 and 41,500 mg/L to 9000 and 6000 mg/L, respectively, within one month. The SO42? concentration, during the anaerobic period, was decreased from 1500 mg/L to 250 mg/L. The sequential treatment had positive effects on nitrification and denitrification efficiencies.

Aris Nikolaou; Apostolos Giannis; Evangelos Gidarakos

2011-01-01T23:59:59.000Z

68

Effects of residues from municipal solid waste landfill on corn yield and heavy metal content  

SciTech Connect

The effects of residues from municipal solid waste landfill, Khon Kaen Municipality, Thailand, on corn (Zea mays L.) yield and heavy metal content were studied. Field experiments with randomized complete block design with five treatments (0, 20, 40, 60 and 80% v/v of residues and soil) and four replications were carried out. Corn yield and heavy metal contents in corn grain were analyzed. Corn yield increased by 50, 72, 85 and 71% at 20, 40, 60 and 80% treatments as compared to the control, respectively. All heavy metals content, except cadmium, nickel and zinc, in corn grain were not significantly different from the control. Arsenic, cadmium and zinc in corn grain were strongly positively correlated with concentrations in soil. The heavy metal content in corn grain was within regulated limits for human consumption.

Prabpai, S. [Suphan Buri Campus Establishment Project, Kasetsart University, 50 U Floor, Administrative Building, Paholyothin Road, Jatujak, Bangkok 10900 (Thailand)], E-mail: s.prabpai@hotmail.com; Charerntanyarak, L. [Department of Epidemiology, Faculty of Public Health, Khon Kaen University, Khon Kaen 40002 (Thailand)], E-mail: lertchai@kku.ac.th; Siri, B. [Department of Agronomy, Faculty of Agriculture, Khon Kaen University, Khon Kaen 40002 (Thailand)], E-mail: boonmee@kku.ac.th; Moore, M.R. [The University of Queensland, The National Research Center for Environmental Toxicology, 39 Kessels Road, Coopers Plans, Brisbane, Queensland 4108 (Australia)], E-mail: m.moore@uq.edu.au; Noller, Barry N. [The University of Queensland, Centre for Mined Land Rehabilitation, Brisbane, Queensland 4072 (Australia)], E-mail: b.noller@uq.edu.au

2009-08-15T23:59:59.000Z

69

Integration of the informal sector into municipal solid waste management in the Philippines - What does it need?  

SciTech Connect

The integration of the informal sector into municipal solid waste management is a challenge many developing countries face. In Iloilo City, Philippines around 220 tons of municipal solid waste are collected every day and disposed at a 10 ha large dumpsite. In order to improve the local waste management system the Local Government decided to develop a new Waste Management Center with integrated landfill. However, the proposed area is adjacent to the presently used dumpsite where more than 300 waste pickers dwell and depend on waste picking as their source of livelihood. The Local Government recognized the hidden threat imposed by the waste picker's presence for this development project and proposed various measures to integrate the informal sector into the municipal solid waste management (MSWM) program. As a key intervention a Waste Workers Association, called USWAG Calahunan Livelihood Association Inc. (UCLA) was initiated and registered as a formal business enterprise in May 2009. Up to date, UCLA counts 240 members who commit to follow certain rules and to work within a team that jointly recovers wasted materials. As a cooperative they are empowered to explore new livelihood options such as the recovery of Alternative Fuels for commercial (cement industry) and household use, production of compost and making of handicrafts out of used packages. These activities do not only provide alternative livelihood for them but also lessen the generation of leachate and Greenhouse Gases (GHG) emissions from waste disposal, whereby the life time of the proposed new sanitary landfill can be extended likewise.

Paul, Johannes G., E-mail: jp.aht.p3@gmail.com [GIZ-AHT Project Office SWM4LGUs, c/o DENR, Iloilo City (Philippines); Arce-Jaque, Joan [GIZ-AHT Project Office SWM4LGUs, c/o DENR, Iloilo City (Philippines); Ravena, Neil; Villamor, Salome P. [General Service Office, City Government, Iloilo City (Philippines)

2012-11-15T23:59:59.000Z

70

A study of the pyrolysis behaviors of pelletized recovered municipal solid waste fuels  

Science Journals Connector (OSTI)

Pelletized recovered solid waste fuel is often applied in gasification systems to provide feedstock with a stabilized quality and high heating value and to avoid the bridging behavior caused by high moisture content, low particle density, and irregular particle size. However, the swelling properties and the sticky material generated from pyrolysis of the plastic group components also tend to trigger bridging in the retorting zone. It is well known that the plastic group materials, which occupy a considerable proportion of municipal solid waste, can melt together easily even under low temperature. This study investigates the pyrolysis behaviors of typical recovered solid waste pellets, including the devolatilization rate, heat transfer properties, char properties, and swelling/shrinkage properties, in a small fixed-bed facility over a wide temperature range, from 900 °C to 450 °C. The results are also compared with those from wheat straw pellets, a typical cellulosic fuel. Moreover, the SEM images and BET analysis of the char structure are further analyzed to provide additional explanation for the mechanisms of swelling/shrinkage phenomena observed during heating.

Chunguang Zhou; Qinglin Zhang; Leonie Arnold; Weihong Yang; Wlodzimierz Blasiak

2013-01-01T23:59:59.000Z

71

Data Summary of Municipal Solid Waste Management Alternatives. Volume VIII: Appendix F - Landfills  

SciTech Connect

While the preceding appendices have focused on the thermochemical approaches to managing municipal solid waste (MSW), this appendix and those that follow on composting and anaerobic digestion address more of the bioconversion process technologies. Landfilling is the historical baseline MSW management option central to every community's solid waste management plan. It generally encompasses shredfills, balefills, landfill gas recovery, and landfill mining. While landfilling is virtually universal in use, it continues to undergo intense scrutiny by the public and regulators alike. Most recently, the US Environmental Protection Agency (EPA) issued its final rule on criteria for designing, operating, monitoring, and closing municipal solid waste landfills. While the Federal government has established nationwide standards and will assist the States in planning and developing their own practices, the States and local governments will carry out the actual planning and direct implementation. The States will also be authorized to devise programs to deal with their specific conditions and needs. While the main body of this appendix and corresponding research was originally prepared in July of 1991, references to the new RCRA Subtitle D, Part 258 EPA regulations have been included in this resubmission (908). By virtue of timing, this appendix is, necessarily, a transition'' document, combining basic landfill design and operation information as well as reference to new regulatory requirements. Given the speed with which landfill practices are and will be changing, the reader is encouraged to refer to Part 258 for additional details. As States set additional requirements and schedules and owners and operators of MSW landfills seek to comply, additional guidance and technical information, including case studies, will likely become available in the literature.

None

1992-10-01T23:59:59.000Z

72

Data summary of municipal solid waste management alternatives. Volume 8, Appendix F, Landfills  

SciTech Connect

While the preceding appendices have focused on the thermochemical approaches to managing municipal solid waste (MSW), this appendix and those that follow on composting and anaerobic digestion address more of the bioconversion process technologies. Landfilling is the historical baseline MSW management option central to every community`s solid waste management plan. It generally encompasses shredfills, balefills, landfill gas recovery, and landfill mining. While landfilling is virtually universal in use, it continues to undergo intense scrutiny by the public and regulators alike. Most recently, the US Environmental Protection Agency (EPA) issued its final rule on criteria for designing, operating, monitoring, and closing municipal solid waste landfills. While the Federal government has established nationwide standards and will assist the States in planning and developing their own practices, the States and local governments will carry out the actual planning and direct implementation. The States will also be authorized to devise programs to deal with their specific conditions and needs. While the main body of this appendix and corresponding research was originally prepared in July of 1991, references to the new RCRA Subtitle D, Part 258 EPA regulations have been included in this resubmission (908). By virtue of timing, this appendix is, necessarily, a ``transition`` document, combining basic landfill design and operation information as well as reference to new regulatory requirements. Given the speed with which landfill practices are and will be changing, the reader is encouraged to refer to Part 258 for additional details. As States set additional requirements and schedules and owners and operators of MSW landfills seek to comply, additional guidance and technical information, including case studies, will likely become available in the literature.

none,

1992-10-01T23:59:59.000Z

73

Micro-scale anaerobic digestion of point source components of organic fraction of municipal solid waste  

SciTech Connect

The fermentation characteristics of six specific types of the organic fraction of municipal solid waste (OFMSW) were examined, with an emphasis on properties that are needed when designing plug-flow type anaerobic bioreactors. More specifically, the decomposition patterns of a vegetable (cabbage), fruits (banana and citrus peels), fresh leaf litter of bamboo and teak leaves, and paper (newsprint) waste streams as feedstocks were studied. Individual OFMSW components were placed into nylon mesh bags and subjected to various fermentation periods (solids retention time, SRT) within the inlet of a functioning plug-flow biogas fermentor. These were removed at periodic intervals, and their composition was analyzed to monitor decomposition rates and changes in chemical composition. Components like cabbage waste, banana peels, and orange peels fermented rapidly both in a plug-flow biogas reactor (PFBR) as well as under a biological methane potential (BMP) assay, while other OFMSW components (leaf litter from bamboo and teak leaves and newsprint) fermented slowly with poor process stability and moderate biodegradation. For fruit and vegetable wastes (FVW), a rapid and efficient removal of pectins is the main cause of rapid disintegration of these feedstocks, which left behind very little compost forming residues (2-5%). Teak and bamboo leaves and newsprint decomposed only to 25-50% in 30 d. These results confirm the potential for volatile fatty acids accumulation in a PFBR's inlet and suggest a modification of the inlet zone or operation of a PFBR with the above feedstocks.

Chanakya, H.N. [Centre for Sustainable Technologies, (formerly ASTRA), Indian Institute of Science, Bangalore 560 012 (India)], E-mail: chanakya@astra.iisc.ernet.in; Sharma, Isha [Centre for Sustainable Technologies, (formerly ASTRA), Indian Institute of Science, Bangalore 560 012 (India); Ramachandra, T.V. [Centre for Sustainable Technologies, (formerly ASTRA), Indian Institute of Science, Bangalore 560 012 (India); Centre for Ecological Sciences, Indian Institute of Science, Bangalore 560 012 (India)

2009-04-15T23:59:59.000Z

74

Simulation of Syngas Production from Municipal Solid Waste Gasification in a Bubbling Fluidized Bed Using Aspen Plus  

Science Journals Connector (OSTI)

Simulation of Syngas Production from Municipal Solid Waste Gasification in a Bubbling Fluidized Bed Using Aspen Plus ... When the reaction kinetics is not known, a rigorous reactor and multiphase equilibrium based on the minimization of the total Gibbs free energy of the product mixture (an RGibbs block) is preferred to predict the equilibrium composition of the produced syngas. ... Catalytic steam gasification of municipal solid waste (MSW) to produce hydrogen-rich gas or syngas (H2 + CO) with calcined dolomite as a catalyst in a bench-scale downstream fixed bed reactor was investigated. ...

Miaomiao Niu; Yaji Huang; Baosheng Jin; Xinye Wang

2013-09-06T23:59:59.000Z

75

A direct steam heat option for hydrothermal treatment of municipal solid waste  

SciTech Connect

A conceptual process for producing a gasifiable slurry from raw municipal solid waste (MSW) using direct steam heating is outlined. The process is based on the hydrothermal decomposition of the organic matter in the MSW, which requires the MSW to be heated to 300-350{degrees}C in the presence of water. A process model is developed and it is shown, based on preliminary estimates of the hydrothermal reaction stoichiometry, that a process using multiple pressure vessels, which allows recovery of waste heat, results in a process capable of producing a product slurry having a 40 wt % solids content with no waste water emissions. Results for a variety of process options and process parameters are presented. It is shown that the addition of auxiliary feedstock to the gasifier, along with the MSW derived slurry, results in more efficient gasification. It is estimated that 2.6 kmol/s of hydrogen can be produced from 30 kg/s (2600 tonne/day) of MSW and 16 kg/s of heavy oil. Without the additional feedstock, heavy oil in this case, only 0.49 kmol/s of hydrogen would be produced.

Thorsness, C.B.

1995-04-12T23:59:59.000Z

76

Combined Municipal Solid Waste and biomass system optimization for district energy applications  

SciTech Connect

Highlights: • Combined energy conversion of MSW and agricultural residue biomass is examined. • The model optimizes the financial yield of the investment. • Several system specifications are optimally defined by the optimization model. • The application to a case study in Greece shows positive financial yield. • The investment is mostly sensitive on the interest rate, the investment cost and the heating oil price. - Abstract: Municipal Solid Waste (MSW) disposal has been a controversial issue in many countries over the past years, due to disagreement among the various stakeholders on the waste management policies and technologies to be adopted. One of the ways of treating/disposing MSW is energy recovery, as waste is considered to contain a considerable amount of bio-waste and therefore can lead to renewable energy production. The overall efficiency can be very high in the cases of co-generation or tri-generation. In this paper a model is presented, aiming to support decision makers in issues relating to Municipal Solid Waste energy recovery. The idea of using more fuel sources, including MSW and agricultural residue biomass that may exist in a rural area, is explored. The model aims at optimizing the system specifications, such as the capacity of the base-load Waste-to-Energy facility, the capacity of the peak-load biomass boiler and the location of the facility. Furthermore, it defines the quantity of each potential fuel source that should be used annually, in order to maximize the financial yield of the investment. The results of an energy tri-generation case study application at a rural area of Greece, using mixed MSW and biomass, indicate positive financial yield of investment. In addition, a sensitivity analysis is performed on the effect of the most important parameters of the model on the optimum solution, pinpointing the parameters of interest rate, investment cost and heating oil price, as those requiring the attention of the decision makers. Finally, the sensitivity analysis is enhanced by a stochastic analysis to determine the effect of the volatility of parameters on the robustness of the model and the solution obtained.

Rentizelas, Athanasios A., E-mail: arent@central.ntua.gr; Tolis, Athanasios I., E-mail: atol@central.ntua.gr; Tatsiopoulos, Ilias P., E-mail: itat@central.ntua.gr

2014-01-15T23:59:59.000Z

77

Evaluation of gasification and novel thermal processes for the treatment of municipal solid waste  

SciTech Connect

This report identifies seven developers whose gasification technologies can be used to treat the organic constituents of municipal solid waste: Energy Products of Idaho; TPS Termiska Processor AB; Proler International Corporation; Thermoselect Inc.; Battelle; Pedco Incorporated; and ThermoChem, Incorporated. Their processes recover heat directly, produce a fuel product, or produce a feedstock for chemical processes. The technologies are on the brink of commercial availability. This report evaluates, for each technology, several kinds of issues. Technical considerations were material balance, energy balance, plant thermal efficiency, and effect of feedstock contaminants. Environmental considerations were the regulatory context, and such things as composition, mass rate, and treatability of pollutants. Business issues were related to likelihood of commercialization. Finally, cost and economic issues such as capital and operating costs, and the refuse-derived fuel preparation and energy conversion costs, were considered. The final section of the report reviews and summarizes the information gathered during the study.

Niessen, W.R.; Marks, C.H.; Sommerlad, R.E. [Camp Dresser and McKee, Inc., Cambridge, MA (United States)] [Camp Dresser and McKee, Inc., Cambridge, MA (United States)

1996-08-01T23:59:59.000Z

78

Risk assessment of gaseous emissions from municipal solid waste landfill: case study Rafah landfill, Palestine  

Science Journals Connector (OSTI)

This article describes the risk assessment of gaseous emissions from the municipal solid waste at Rafah landfill, Palestine. In this study, Gas-Sim model was used to quantify the gaseous emissions from the landfill and the Land-Gem model was used to verify the results. Risk assessment of both carcinogens and non-carcinogens were performed. Two scenarios were conducted namely with plant uptake and without plant uptake. The scenario with plant uptake revealed that the risk to residents is acceptable for non-carcinogens (risk value 0.45 > 1.0), while the risk to residents is not acceptable for carcinogens (risk value 2.69 × 10?6 risk to residents is acceptable for non-carcinogens (risk value 0.42 > 1.0), while the risk to residents is acceptable for carcinogens (risk value 2.855 × 10?7 > 10?6).

Ahmad A. Foul; Mazen Abualtayef; Basel Qrenawi

2014-01-01T23:59:59.000Z

79

Municipal Solid Waste Landfills The following Oklahoma landfills currently accept dead livestock. As each facility has different guidelines and  

E-Print Network (OSTI)

Municipal Solid Waste Landfills The following Oklahoma landfills currently accept dead livestock Adair Cherokee Nation Landfill 918-696-5342 Canadian OEMA Landfill 405-262-0161 Call ahead Carter Southern Okla. Regional Disposal Landfill 580-226-1276 Comanche City of Lawton Landfill 580

Balasundaram, Balabhaskar "Baski"

80

Municipal Waste Combustion (New Mexico)  

Energy.gov (U.S. Department of Energy (DOE))

This rule establishes requirements for emissions from, and design and operation of, municipal waste combustion units. "Municipal waste" means all materials and substances discarded from residential...

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Co-gasification of municipal solid waste and material recovery in a large-scale gasification and melting system  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer This study evaluates the effects of co-gasification of MSW with MSW bottom ash. Black-Right-Pointing-Pointer No significant difference between MSW treatment with and without MSW bottom ash. Black-Right-Pointing-Pointer PCDD/DFs yields are significantly low because of the high carbon conversion ratio. Black-Right-Pointing-Pointer Slag quality is significantly stable and slag contains few hazardous heavy metals. Black-Right-Pointing-Pointer The final landfill amount is reduced and materials are recovered by DMS process. - Abstract: This study evaluates the effects of co-gasification of municipal solid waste with and without the municipal solid waste bottom ash using two large-scale commercial operation plants. From the viewpoint of operation data, there is no significant difference between municipal solid waste treatment with and without the bottom ash. The carbon conversion ratios are as high as 91.7% and 95.3%, respectively and this leads to significantly low PCDD/DFs yields via complete syngas combustion. The gross power generation efficiencies are 18.9% with the bottom ash and 23.0% without municipal solid waste bottom ash, respectively. The effects of the equivalence ratio are also evaluated. With the equivalence ratio increasing, carbon monoxide concentration is decreased, and carbon dioxide and the syngas temperature (top gas temperature) are increased. The carbon conversion ratio is also increased. These tendencies are seen in both modes. Co-gasification using the gasification and melting system (Direct Melting System) has a possibility to recover materials effectively. More than 90% of chlorine is distributed in fly ash. Low-boiling-point heavy metals, such as lead and zinc, are distributed in fly ash at rates of 95.2% and 92.0%, respectively. Most of high-boiling-point heavy metals, such as iron and copper, are distributed in metal. It is also clarified that slag is stable and contains few harmful heavy metals such as lead. Compared with the conventional waste management framework, 85% of the final landfill amount reduction is achieved by co-gasification of municipal solid waste with bottom ash and incombustible residues. These results indicate that the combined production of slag with co-gasification of municipal solid waste with the bottom ash constitutes an ideal approach to environmental conservation and resource recycling.

Tanigaki, Nobuhiro, E-mail: tanigaki.nobuhiro@nsc-eng.co.jp [Nippon Steel Engineering Co., Ltd. (Head Office), Osaki Center Building 1-5-1, Osaki, Shinagawa-ku, Tokyo 141-8604 (Japan); Manako, Kazutaka [Nippon Steel Engineering Co., Ltd., 46-59, Nakabaru, Tobata-ku, Kitakyushu, Fukuoka 804-8505 (Japan); Osada, Morihiro [Nippon Steel Engineering Co., Ltd. (Head Office), Osaki Center Building 1-5-1, Osaki, Shinagawa-ku, Tokyo 141-8604 (Japan)

2012-04-15T23:59:59.000Z

82

Methane Production Quantification and Energy Estimation for Bangalore Municipal Solid Waste  

Science Journals Connector (OSTI)

Landfills are considered as cornerstone of solid waste management. Landfill gas (LFG) and leachate are principal outputs ... from landfills. Methane, occupying significant volume of landfill gas, has considerable...

A. Kumar; R. Dand; P. Lakshmikanthan…

2014-01-01T23:59:59.000Z

83

Modeling and comparative assessment of municipal solid waste gasification for energy production  

SciTech Connect

Highlights: • Study developed a methodology for the evaluation of gasification for MSW treatment. • Study was conducted comparatively for USA, UAE, and Thailand. • Study applies a thermodynamic model (Gibbs free energy minimization) using the Gasify software. • The energy efficiency of the process and the compatibility with different waste streams was studied. - Abstract: Gasification is the thermochemical conversion of organic feedstocks mainly into combustible syngas (CO and H{sub 2}) along with other constituents. It has been widely used to convert coal into gaseous energy carriers but only has been recently looked at as a process for producing energy from biomass. This study explores the potential of gasification for energy production and treatment of municipal solid waste (MSW). It relies on adapting the theory governing the chemistry and kinetics of the gasification process to the use of MSW as a feedstock to the process. It also relies on an equilibrium kinetics and thermodynamics solver tool (Gasify®) in the process of modeling gasification of MSW. The effect of process temperature variation on gasifying MSW was explored and the results were compared to incineration as an alternative to gasification of MSW. Also, the assessment was performed comparatively for gasification of MSW in the United Arab Emirates, USA, and Thailand, presenting a spectrum of socioeconomic settings with varying MSW compositions in order to explore the effect of MSW composition variance on the products of gasification. All in all, this study provides an insight into the potential of gasification for the treatment of MSW and as a waste to energy alternative to incineration.

Arafat, Hassan A., E-mail: harafat@masdar.ac.ae; Jijakli, Kenan

2013-08-15T23:59:59.000Z

84

Data summary of municipal solid waste management alternatives. Volume 11, Alphabetically indexed bibliography  

SciTech Connect

This appendix contains the alphabetically indexed bibliography for the complete group of reports on municipal waste management alternatives. The references are listed for each of the following topics: mass burn technologies, RDF technologies, fluidized-bed combustion, pyrolysis and gasification of MSW, materials recovery- recycling technologies, sanitary landfills, composting, and anaerobic digestion of MSW.

none,

1992-10-01T23:59:59.000Z

85

An integrated appraisal of energy recovery options in the United Kingdom using solid recovered fuel derived from municipal solid waste  

SciTech Connect

This paper reports an integrated appraisal of options for utilising solid recovered fuels (SRF) (derived from municipal solid waste, MSW) in energy intensive industries within the United Kingdom (UK). Four potential co-combustion scenarios have been identified following discussions with industry stakeholders. These scenarios have been evaluated using (a) an existing energy and mass flow framework model, (b) a semi-quantitative risk analysis, (c) an environmental assessment and (d) a financial assessment. A summary of results from these evaluations for the four different scenarios is presented. For the given ranges of assumptions; SRF co-combustion with coal in cement kilns was found to be the optimal scenario followed by co-combustion of SRF in coal-fired power plants. The biogenic fraction in SRF (ca. 70%) reduces greenhouse gas (GHG) emissions significantly ({approx}2500 g CO{sub 2} eqvt./kg DS SRF in co-fired cement kilns and {approx}1500 g CO{sub 2} eqvt./kg DS SRF in co-fired power plants). Potential reductions in electricity or heat production occurred through using a lower calorific value (CV) fuel. This could be compensated for by savings in fuel costs (from SRF having a gate fee) and grants aimed at reducing GHG emission to encourage the use of fuels with high biomass fractions. Total revenues generated from coal-fired power plants appear to be the highest ( Pounds 95/t SRF) from the four scenarios. However overall, cement kilns appear to be the best option due to the low technological risks, environmental emissions and fuel cost. Additionally, cement kiln operators have good experience of handling waste derived fuels. The scenarios involving co-combustion of SRF with MSW and biomass were less favourable due to higher environmental risks and technical issues.

Garg, A.; Smith, R. [Sustainable Systems Department, School of Applied Sciences, Cranfield University, Cranfield, Bedfordshire, MK43 0AL (United Kingdom); Hill, D. [DPH Environment and Energy Ltd., c/o Sustainable Systems Department, School of Applied Sciences, Cranfield University, Cranfield, Bedfordshire, MK43 0AL (United Kingdom); Longhurst, P.J.; Pollard, S.J.T. [Sustainable Systems Department, School of Applied Sciences, Cranfield University, Cranfield, Bedfordshire, MK43 0AL (United Kingdom); Simms, N.J. [Sustainable Systems Department, School of Applied Sciences, Cranfield University, Cranfield, Bedfordshire, MK43 0AL (United Kingdom)], E-mail: n.j.simms@cranfield.ac.uk

2009-08-15T23:59:59.000Z

86

Energy recovery from municipal solid waste and sewage sludge using multi-solid fluidized bed combustion technology  

SciTech Connect

This study was initiated to investigate the recovery of energy from municipal solid waste (MSW) and domestic sewage sludge (DSS) simultaneously by using Battelle's multi-solid fluidized-bed combustion (MS-FBC) technology. The concept was to recover energy as high and low pressure steam, simultaneously. High pressure steam would be generated from flue gas using a conventional tubular boiler. Low pressure steam would be generated by direct contact drying of DSS (as 4% solids) with hot sand in a fluidized bed that is an integral part of the MS-FBC process. It was proposed that high pressure steam could be used for district heating or electricity generation. The low pressure steam could be used for close proximity building heat. Alternatively, low pressure steam could be used to heat wastewater in a sewage treatment plant to enhance sedimentation and biological activity that would provide a captive market for this part of the recovered energy. The direct contact drying or tubeless steam generation eliminates fouling problems that are common during heat exchange with DSS. The MS-FBC process was originally developed for coal and was chosen for this investigation because its combustion rate is about three times that of conventional fluidized beds and it was projected to have the flexibility needed for accomplishing tubeless steam generation. The results of the investigation show that the MS-FBC process concept for the co-utilization of MSW and DSS is technically feasible and that the thermal efficiency of the process is 76 to 82% based on experiments conducted in a 70 to 85 lb/h pilot plant and calculations on three conceptual cases.

Not Available

1981-07-01T23:59:59.000Z

87

Short mechanical biological treatment of municipal solid waste allows landfill impact reduction saving waste energy content  

Science Journals Connector (OSTI)

Abstract The aim of this work was to evaluate the effects of full scale MBT process (28 d) in removing inhibition condition for successive biogas (ABP) production in landfill and in reducing total waste impact. For this purpose the organic fraction of MSW was treated in a full-scale MBT plant and successively incubated vs. untreated waste, in simulated landfills for one year. Results showed that untreated landfilled-waste gave a total ABP reduction that was null. On the contrary MBT process reduced ABP of 44%, but successive incubation for one year in landfill gave a total ABP reduction of 86%. This ABP reduction corresponded to a MBT process of 22 weeks length, according to the predictive regression developed for ABP reduction vs. MBT-time. Therefore short MBT allowed reducing landfill impact, preserving energy content (ABP) to be produced successively by bioreactor technology since pre-treatment avoided process inhibition because of partial waste biostabilization.

Barbara Scaglia; Silvia Salati; Alessandra Di Gregorio; Alberto Carrera; Fulvia Tambone; Fabrizio Adani

2013-01-01T23:59:59.000Z

88

The composition, heating value and renewable share of the energy content of mixed municipal solid waste in Finland  

Science Journals Connector (OSTI)

Abstract For the estimation of greenhouse gas emissions from waste incineration it is essential to know the share of the renewable energy content of the combusted waste. The composition and heating value information is generally available, but the renewable energy share or heating values of different fractions of waste have rarely been determined. In this study, data from Finnish studies concerning the composition and energy content of mixed MSW were collected, new experimental data on the compositions, heating values and renewable share of energy were presented and the results were compared to the estimations concluded from earlier international studies. In the town of Lappeenranta in south-eastern Finland, the share of renewable energy ranged between 25% and 34% in the energy content tests implemented for two sample trucks. The heating values of the waste and fractions of plastic waste were high in the samples compared to the earlier studies in Finland. These high values were caused by good source separation and led to a low share of renewable energy content in the waste. The results showed that in mixed municipal solid waste the renewable share of the energy content can be significantly lower than the general assumptions (50–60%) when the source separation of organic waste, paper and cardboard is carried out successfully. The number of samples was however small for making extensive conclusions on the results concerning the heating values and renewable share of energy and additional research is needed for this purpose.

M. Horttanainen; N. Teirasvuo; V. Kapustina; M. Hupponen; M. Luoranen

2013-01-01T23:59:59.000Z

89

Combustion of municipal solid wastes with oil shale in a circulating fluidized bed. Quarterly report, quarter ending December 31, 1995  

SciTech Connect

The objective of this project is to demonstrate that cocombustion of municipal solid waste and oil shale can reduce emissions of gaseous pollutants (SO{sub 2} and HCl) to acceptable levels. Tests in 6- and 15-inch units showed that the oil shale absorbs acid gas pollutants and produces an ash which could be, at the least, disposed of in a normal landfill. Further analysis of the results are underway to estimate scale-up to commercial size. Additional work will be done to evaluate the cementitious properties of oil shale ash.

NONE

1996-01-01T23:59:59.000Z

90

Solid Waste Management Plan. Revision 4  

SciTech Connect

The waste types discussed in this Solid Waste Management Plan are Municipal Solid Waste, Hazardous Waste, Low-Level Mixed Waste, Low-Level Radioactive Waste, and Transuranic Waste. The plan describes for each type of solid waste, the existing waste management facilities, the issues, and the assumptions used to develop the current management plan.

NONE

1995-04-26T23:59:59.000Z

91

Prompt gamma ray neutron activation analysis of cadmium in municipal solid waste  

E-Print Network (OSTI)

EXPERIMENTAL. . 26 PGNAA Assembly. Detection System Background Determination of Detector Shielding. Self-Shielding. Optimal Bag Size and Orientation. . . . . . . . . . . . . . . Detection Limit and Sensitivity. . . . . . . . . . . . . . . . Neutron Flux... solid waste. This study modified a previous setup that was in a shadow- shield arrangement using Pu-Be neutron sources by: more elaborate detector shielding to reduce background levels; and, irradiating the target bilaterally. The system background...

Dendahl, Katherine Hoge

2012-06-07T23:59:59.000Z

92

Data summary of municipal solid waste management alternatives. Volume 7, Appendix E -- Material recovery/material recycling technologies  

SciTech Connect

The enthusiasm for and commitment to recycling of municipal solid wastes is based on several intuitive benefits: Conservation of landfill capacity; Conservation of non-renewable natural resources and energy sources; Minimization of the perceived potential environmental impacts of MSW combustion and landfilling; Minimization of disposal costs, both directly and through material resale credits. In this discussion, ``recycling`` refers to materials recovered from the waste stream. It excludes scrap materials that are recovered and reused during industrial manufacturing processes and prompt industrial scrap. Materials recycling is an integral part of several solid waste management options. For example, in the preparation of refuse-derived fuel (RDF), ferrous metals are typically removed from the waste stream both before and after shredding. Similarly, composting facilities, often include processes for recovering inert recyclable materials such as ferrous and nonferrous metals, glass, Plastics, and paper. While these two technologies have as their primary objectives the production of RDF and compost, respectively, the demonstrated recovery of recyclables emphasizes the inherent compatibility of recycling with these MSW management strategies. This appendix discusses several technology options with regard to separating recyclables at the source of generation, the methods available for collecting and transporting these materials to a MRF, the market requirements for post-consumer recycled materials, and the process unit operations. Mixed waste MRFs associated with mass bum plants are also presented.

none,

1992-10-01T23:59:59.000Z

93

Environmental impacts of residual Municipal Solid Waste incineration: A comparison of 110 French incinerators using a life cycle approach  

SciTech Connect

Highlights: • 110 French incinerators are compared with LCA based on plant-specific data. • Environmental impacts vary as a function of plants energy recovery and NO{sub x} emissions. • E.g. climate change impact ranges from ?58 to 408 kg CO{sub 2}-eq/tonne of residual MSW. • Implications for LCA of waste management in a decision-making process are detailed. - Abstract: Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e. 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of ?58 kg CO{sub 2}-eq to a relatively large burden of 408 kg CO{sub 2}-eq, with 294 kg CO{sub 2}-eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NO{sub x} process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available.

Beylot, Antoine, E-mail: a.beylot@brgm.fr; Villeneuve, Jacques

2013-12-15T23:59:59.000Z

94

The estimation of N{sub 2}O emissions from municipal solid waste incineration facilities: The Korea case  

SciTech Connect

The greenhouse gases (GHGs) generated in municipal solid waste (MSW) incineration are carbon dioxide (CO{sub 2}), methane (CH{sub 4}), and nitrous oxide (N{sub 2}O). In South Korea case, the total of GHGs from the waste incineration facilities has been increasing at an annual rate 10%. In these view, waste incineration facilities should consider to reduce GHG emissions. This study is designed to estimate the N{sub 2}O emission factors from MSW incineration plants, and calculate the N{sub 2}O emissions based on these factors. The three MSW incinerators examined in this study were either stoker or both stoker and rotary kiln facilities. The N{sub 2}O concentrations from the MSW incinerators were measured using gas chromatography-electron capture detection (GC-ECD) equipment. The average of the N{sub 2}O emission factors for the M01 plant, M02 plant, and M03 plant are 71, 75, and 153 g-N{sub 2}O/ton-waste, respectively. These results showed a significant difference from the default values of the intergovernmental panel on climate change (IPCC), while approaching those values derived in Japan and Germany. Furthermore, comparing the results of this study to the Korea Energy Economics Institute (KEEI) (2007) data on waste incineration, N{sub 2}O emissions from MSW incineration comprised 19% of the total N{sub 2}O emissions.

Park, Sangwon; Choi, Jun-Ho [Department of Chemical and Biomolecular Engineering, Yonsei University, 262 Seongsanno, Seodaemun-gu, Seoul 120-749 (Korea, Republic of); Park, Jinwon, E-mail: jwpark@yonsei.ac.kr [Department of Chemical and Biomolecular Engineering, Yonsei University, 262 Seongsanno, Seodaemun-gu, Seoul 120-749 (Korea, Republic of)

2011-08-15T23:59:59.000Z

95

Quality Services: Solid Wastes, Part 360: Solid Waste Management Facilities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0: Solid Waste Management 0: Solid Waste Management Facilities (New York) Quality Services: Solid Wastes, Part 360: Solid Waste Management Facilities (New York) < Back Eligibility Agricultural Commercial Fuel Distributor Industrial Institutional Investor-Owned Utility Multi-Family Residential Municipal/Public Utility Rural Electric Cooperative Transportation Utility Program Info State New York Program Type Environmental Regulations Provider NY Department of Environmental Conservation These regulations apply to all solid wastes with the exception of hazardous or radioactive waste. Proposed solid waste processing facilities are required to obtain permits prior to construction, and the regulations provide details about permitting, construction, registration, and operation requirements. The regulations contain specific guidance for land

96

Combustion of municipal solid wastes with oil shale in a circulating fluidized bed. Quarterly report, quarter ending 31 December 1994  

SciTech Connect

The test plan is designed to demonstrate that oil shale co-combusted with municipal solid waste (MSW) can reduce gaseous pollutants (SO{sub 2}, CO) to acceptable levels (90%+ reduction) and produce a cementitious ash which will, at a minimum, be acceptable in normal land fills. The small-scale combustion testing will be accomplished in a 6-in. circulating fluid bed combustor (CFBC) at Hazen Research Laboratories. This work will be patterned after the study the authors conducted in 1988 when coal and oil shale were co-combusted in a program sponsored by the Electric Power Research Institute. The specific purpose of the test program will be to: determine the required ratio of oil shale to MSW by determining the ratio of absorbent to pollutant (A/P); determine the effect of temperature and resident time in the reactor; and determine if kinetic model developed for coal/oil shale mixture is applicable.

Not Available

1995-01-01T23:59:59.000Z

97

Emissions of PCDD/Fs from municipal solid waste incinerators in China Yuwen Ni, Haijun Zhang, Su Fan, Xueping Zhang, Qing Zhang, Jiping Chen *  

E-Print Network (OSTI)

Emissions of PCDD/Fs from municipal solid waste incinerators in China Yuwen Ni, Haijun Zhang, Su February 2009 Available online 21 March 2009 Keywords: MSWIs PCDD/Fs Congener patterns Emission factor a b s t r a c t Gas emission of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD

Columbia University

98

Fuel-Slurry Integrated Gasifier/Gas Turbine (FSIG/GT) Alternative for Power Generation Applied to Municipal Solid Waste (MSW)  

Science Journals Connector (OSTI)

The gas is cleaned to bring the particle content and size as well alkaline concentration within the acceptable limits for injections into standard gas turbines. ... The proper disposal and use of Municipal Solid Wastes (MSW) for power generation remains among the most pressing problems of medium to large cities. ... Bubble sizes and raising velocities through the gasifier bed (Configuration A). ...

Marcio L. de Souza-Santos; Kevin B. Ceribeli

2013-11-22T23:59:59.000Z

99

Leaching behavior and possible resource recovery from air pollution control residues of fluidized bed combustion of municipal solid waste  

SciTech Connect

Ash residues are generated at several points during combustion of municipal solid waste (MSW), i.e., in cyclones, electrostatic precipitators and fabric filters. Such residues are of a complex physical and chemical nature and are often enriched in soluble salts and heavy metals such as Pb, Cd and Zn. Fluidized bed combustion (FBC) of MSW is a relatively new technique and very little information is available about the leaching behavior of its residues. In this study, the total elemental composition, mineralogy and leaching behavior of cyclone and bag-house filter ashes from a bubbling fluidized bed (BFB) boiler fired with municipal solid waste have been investigated. In addition, the possibilities of recovery heavy metals from these ashes were studied. The long-term leaching behavior of the ash constituents was evaluated using a two-step batch leaching test known as the CEN-test, whereas short and medium term leaching behavior was evaluated using a Column test. The extraction of elements from cyclone and filter ashes with various acidic solutions was also investigated. The leaching behavior of acid washed ashes was evaluated using the CEN test. The cyclone ash was mainly composed of aluminosilicate minerals, whereas the filter ash consisted of chlorides and hydroxides of alkali and alkaline earth metals. The concentration of heavy metals such as Zn, Cu, Cd and Pb was higher in the filter ash than in the cyclone ash. The leached amounts of sulfates and Pb from the cyclone ash decreased with leaching test contact time, indicating the formation of secondary mineral phases. Large amounts of chlorides, sulfates, Ca, Cu and Pb were leached from the filter ash. Acid extraction removed large amounts ({gt}50%) of Zn, Pb and Cu from the filter ash and approximately 56% of the total amount of Zn present in the cyclone ash. An efficient removal of heavy metal species from these types of ashes can probably be achieved by application of a recycling or multi-step process.

Abbas, Z.; Andersson, B.A.; Steenari, B.M.

1999-07-01T23:59:59.000Z

100

E-Print Network 3.0 - art municipal waste Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Combustion of Municipal Solid Waste," Second Conference... on Municipal, Hazardous and Coal ... Source: Columbia University, Department of Earth and Environmental Engineering,...

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Thermal conversion of municipal solid waste via hydrothermal carbonization: Comparison of carbonization products to products from current waste management techniques  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Hydrothermal carbonization (HTC) is a novel thermal conversion process. Black-Right-Pointing-Pointer HTC converts wastes into value-added resources. Black-Right-Pointing-Pointer Carbonization integrates majority of carbon into solid-phase. Black-Right-Pointing-Pointer Carbonization results in a hydrochar with high energy density. Black-Right-Pointing-Pointer Using hydrochar as an energy source may be beneficial. - Abstract: Hydrothermal carbonization (HTC) is a novel thermal conversion process that may be a viable means for managing solid waste streams while minimizing greenhouse gas production and producing residual material with intrinsic value. HTC is a wet, relatively low temperature (180-350 Degree-Sign C) thermal conversion process that has been shown to convert biomass to a carbonaceous residue referred to as hydrochar. Results from batch experiments indicate HTC of representative waste materials is feasible, and results in the majority of carbon (45-75% of the initially present carbon) remaining within the hydrochar. Gas production during the batch experiments suggests that longer reaction periods may be desirable to maximize the production of energy-favorable products. If using the hydrochar for applications in which the carbon will remain stored, results suggest that the gaseous products from HTC result in fewer g CO{sub 2}-equivalent emissions than the gases associated with landfilling, composting, and incineration. When considering the use of hydrochar as a solid fuel, more energy can be derived from the hydrochar than from the gases resulting from waste degradation during landfilling and anaerobic digestion, and from incineration of food waste. Carbon emissions resulting from the use of the hydrochar as a fuel source are smaller than those associated with incineration, suggesting HTC may serve as an environmentally beneficial alternative to incineration. The type and extent of environmental benefits derived from HTC will be dependent on hydrochar use/the purpose for HTC (e.g., energy generation or carbon storage).

Lu Xiaowei; Jordan, Beth [Department of Civil and Environmental Engineering, University of South Carolina, 300 Main Street, Columbia, SC 29208 (United States); Berge, Nicole D., E-mail: berge@cec.sc.edu [Department of Civil and Environmental Engineering, University of South Carolina, 300 Main Street, Columbia, SC 29208 (United States)

2012-07-15T23:59:59.000Z

102

Clean energy from municipal solid waste. ERIP technical progress report {number_sign}6  

SciTech Connect

The ground carbonized RDF slurry from the grinding trials at IKA Works at approximately 50 wt.% solids was sealed in drums and shipped to the Energy and Environmental Research Corporation (EER) for the dioxin/furan and trace heavy metal combustion tests. In addition, a fuel characterization and trace component analysis was completed for this final carbonized RDF slurry fuel. This final fuel was a blend of several fuels from the pilot scale slurry carbonization experiments. As can be seen from the data, the final carbonized RDF has an exceptional heating value and volatile matter content. In addition, trace components are significantly lower than the raw RDF pellets. The report summarizes results from combustion tests and air pollution monitoring of these tests. For the upcoming time period 10/96--01/97, it is anticipated that the analysis of the dioxin/furan and trace heavy metal combustion test will be completed. This analysis includes rheology and particle size distribution analysis of the carbonized RDF slurry fuel, carbon content and TCLP of the combustion ash, trace heavy metal balances around combustor, and dioxin/furan emissions. Finally, the slurry carbonization computer model and computer simulations will be completed in the next reporting period (including the waste water treatment subsystem). Based upon this computer model, initial economic estimates and optimizations of the slurry carbonization process will be completed in the next reporting period.

NONE

1996-10-08T23:59:59.000Z

103

Eco-efficiency for greenhouse gas emissions mitigation of municipal solid waste management: A case study of Tianjin, China  

SciTech Connect

The issue of municipal solid waste (MSW) management has been highlighted in China due to the continually increasing MSW volumes being generated and the limited capacity of waste treatment facilities. This article presents a quantitative eco-efficiency (E/E) analysis on MSW management in terms of greenhouse gas (GHG) mitigation. A methodology for E/E analysis has been proposed, with an emphasis on the consistent integration of life cycle assessment (LCA) and life cycle costing (LCC). The environmental and economic impacts derived from LCA and LCC have been normalized and defined as a quantitative E/E indicator. The proposed method was applied in a case study of Tianjin, China. The study assessed the current MSW management system, as well as a set of alternative scenarios, to investigate trade-offs between economy and GHG emissions mitigation. Additionally, contribution analysis was conducted on both LCA and LCC to identify key issues driving environmental and economic impacts. The results show that the current Tianjin's MSW management system emits the highest GHG and costs the least, whereas the situation reverses in the integrated scenario. The key issues identified by the contribution analysis show no linear relationship between the global warming impact and the cost impact in MSW management system. The landfill gas utilization scenario is indicated as a potential optimum scenario by the proposed E/E analysis, given the characteristics of MSW, technology levels, and chosen methodologies. The E/E analysis provides an attractive direction towards sustainable waste management, though some questions with respect to uncertainty need to be discussed further.

Zhao Wei, E-mail: zhaowei.tju@gmail.com [College of Civil Engineering and Architecture, Liaoning University of Technology, 121000 Jinzhou (China); Institute of Environmental Sciences (CML), Leiden University, P.O. Box 9518, 2300RA Leiden (Netherlands); Huppes, Gjalt, E-mail: huppes@cml.leidenuniv.nl [Institute of Environmental Sciences (CML), Leiden University, P.O. Box 9518, 2300RA Leiden (Netherlands); Voet, Ester van der, E-mail: Voet@cml.leidenuniv.nl [Institute of Environmental Sciences (CML), Leiden University, P.O. Box 9518, 2300RA Leiden (Netherlands)

2011-06-15T23:59:59.000Z

104

Effect of air flow rate and fuel moisture on the burning behaviours of biomass and simulated municipal solid wastes in packed beds  

Science Journals Connector (OSTI)

Combustion of biomass and municipal solid wastes is one of the key areas in the global cleaner energy strategy. But there is still a lack of detailed and systematically theoretical study on the packed bed burning of biomass and municipal solid wastes. The advantage of theoretical study lies in its ability to reveal features of the detailed structure of the burning process inside a solid bed, such as reaction zone thickness, combustion staging, rates of individual sub-processes, gas emission and char burning characteristics. These characteristics are hard to measure by conventional experimental techniques. In this paper, mathematical simulations as well as experiments have been carried out for the combustion of wood chips and the incineration of simulated municipal solid wastes in a bench-top stationary bed and the effects of primary air flow rate and moisture level in the fuel have been assessed over wide ranges. It is found that volatile release as well as char burning intensifies with an increase in the primary air flow until a critical point is reached where a further increase in the primary air results in slowing down of the combustion process; a higher primary airflow also reduces the char fraction burned in the final char-burning-only stage, shifts combustion in the bed to a more fuel-lean environment and reduces CO emission at the bed top; an increase in the moisture level in the fuel produces a higher flame front temperature in the bed at low primary air flow rates.

Y.B Yang; V.N Sharifi; J Swithenbank

2004-01-01T23:59:59.000Z

105

Municipal solid waste management in the Southern Province of Sri Lanka: Problems, issues and challenges  

SciTech Connect

This paper describes the problems, issues and challenges faced by Sri Lanka based on the outcome of a recent study conducted in the country's Southern Province. The study consists of a public survey, discussions with local authority staff involved in waste management, discussions with Provincial Council and Government officials, dialogue with local politicians, review of documents and field observations. The study revealed that only 24% of the households have access to waste collection and that in rural areas it was less than 2%. A substantial number of households in areas without waste collection expect local authorities to collect their waste. The study also showed that most sites in the province are under capacity to handle any increased demand. Urgent and immediate improvement of the waste disposal sites is necessary to meet the current demand for improved waste collection. The study also revealed that there is a high willingness of people for home composting.

Vidanaarachchi, Chandana K. [Department of Civil and Environmental Engineering, University of Melbourne, Parkville, Vic. 3010 (Australia)]. E-mail: c.vidanaarachchi@civenv.unimelb.edu.au; Yuen, Samuel T.S. [Department of Civil and Environmental Engineering, University of Melbourne, Parkville, Vic. 3010 (Australia); Pilapitiya, Sumith [World Bank (Colombo Office), P.O. Box 1761, Colombo 3 (Sri Lanka)

2006-07-01T23:59:59.000Z

106

Critical review of size-reduction and separation equipment used on municipal solid waste  

E-Print Network (OSTI)

municipal refuse for further processing as incineration, pyrolysis or biodegradation. Combinations of separation and size-reduction steps often are referred to as "front-end" systems because this is the first step in the overall con- version process... refuse for further processing by incineration, pyrolysis or biodegradation methods in the conversion and recovery of energy products and resources. Because of this first position in the overall conversion system, such com- binations of separation...

Chin, Billy Show-Ming

1975-01-01T23:59:59.000Z

107

Production of methane gas from organic fraction municipal solid waste (OFMSW) via anaerobic process: application methodology for the Malaysian condition  

Science Journals Connector (OSTI)

Solid waste management in Malaysia is confronted with many problems, including low collection coverage, irregular collection services, inadequate equipment used for waste collection, crude open dumping and burning without air and water pollution control systems, inadequate legal provisions and resource constraints. These problems have various effects on the development of the solid waste management system in Malaysia. Anaerobic digestion has been suggested as an alternative method for removing high concentrations of organic waste. In this study, two types of anaerobic digesters which are Simulated Landfill Bioreactor (SLBR) and Anaerobic Solid-Liquid (ASL) reactor were proposed. The reactors were operated at a temperature 60°C, analysed for biogas production and volatile fatty acid.

Irnis Azura Zakarya; Ismail Abustan; Norli Ismail; Mohd Suffian Yusoff

2013-01-01T23:59:59.000Z

108

Mercury in Municipal Solid Waste in China and Its Control: A Review  

Science Journals Connector (OSTI)

Regulation on mercury content limitation for batteries; China Light Industry Association: Beijing, China, 1997. ... The 2015 scheme 2 assumes mercury use by the battery industry is reduced to 26 Mg,(95) and mercury use by the lighting industry increases to 90 Mg (due to market growth), while the production and disposal patterns of mercury-containing medical devices are the same as the base case. ... Mercury-bearing material has been placed in municipal landfills from a wide array of sources including fluorescent lights, batteries, elec. ...

Hefa Cheng; Yuanan Hu

2011-12-02T23:59:59.000Z

109

Environmental impact of APC residues from municipal solid waste incineration: Reuse assessment based on soil and surface water protection criteria  

SciTech Connect

Highlights: > The Dutch Building Material Decree (BMD) was used to APC residues from MSWI. > BMD is a straightforward tool to calculate expectable loads to the environment of common pollutants. > Chloride load to the environment lead to classification of building material not allowed. > At least a pre-treatment (e.g. washing) is required in order to remove soluble salts. > The stabilization with phosphates or silicates eliminate the problem of heavy metals. - Abstract: Waste management and environmental protection are mandatory requirements of modern society. In our study, air pollution control (APC) residues from municipal solid waste incinerators (MSWI) were considered as a mixture of fly ash and fine particulate solids collected in scrubbers and fabric filters. These are hazardous wastes and require treatment before landfill. Although there are a number of treatment options, it is highly recommended to find practical applications rather than just dump them in landfill sites. In general, for using a construction material, beyond technical specifications also soil and surface water criteria may be used to ensure environmental protection. The Dutch Building Materials Decree (BMD) is a valuable tool in this respect and it was used to investigate which properties do not meet the threshold criteria so that APC residues can be further used as secondary building material. To this end, some scenarios were evaluated by considering release of inorganic species from unmoulded and moulded applications. The main conclusion is that the high amount of soluble salts makes the APC residues a building material prohibited in any of the conditions tested. In case of moulding materials, the limits of heavy metals are complied, and their use in Category 1 would be allowed. However, also in this case, the soluble salts lead to the classification of 'building material not allowed'. The treatments with phosphates or silicates are able to solve the problem of heavy metals, but difficulties with the soluble salts are still observed. This analysis suggests that for APC residues to comply with soil and surface water protection criteria to be further used as building material at least a pre-treating for removing soluble salts is absolutely required.

Quina, Margarida J., E-mail: guida@eq.uc.pt [Research Centre on Chemical Processes Engineering and Forest Products, Department of Chemical Engineering, University of Coimbra, Rua Silvio Lima, 3030-790 Coimbra (Portugal); Bordado, Joao C.M. [Department of Chemical and Biological Engineering, IBB, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Quinta-Ferreira, Rosa M. [Research Centre on Chemical Processes Engineering and Forest Products, Department of Chemical Engineering, University of Coimbra, Rua Silvio Lima, 3030-790 Coimbra (Portugal)

2011-09-15T23:59:59.000Z

110

THERMODYNAMIC STUDY OF HEAVY METALS BEHAVIOUR DURING MUNICIPAL WASTE INCINERATION  

E-Print Network (OSTI)

, heat and mass transfer, drying, pyrolysis, combustion of pyrolysis gases, combustion and gasificationTHERMODYNAMIC STUDY OF HEAVY METALS BEHAVIOUR DURING MUNICIPAL WASTE INCINERATION Y. ME´ NARD, A Me´tallurgie (LSG2M) Nancy, France T he incineration of municipal solid waste (MSW) contributes

Boyer, Edmond

111

Solute transport under steady and transient conditions in biodegraded municipal solid waste  

E-Print Network (OSTI)

for water movement, presented in a previous paper, and a strict convective solute flux law. The waste medium is conceptualized as a three-domain system consisting of a mobile domain (channels), an immobile fast domain, and an immobile slow domain. The mobile...

Bendz, David; Singh, Vijay P.

112

The feasibility of source segregation as the first step for a municipal solid waste disposal scheme  

E-Print Network (OSTI)

Analysis Incineration. Pyrolysis Composting. Anaerobic Digestion. Material Recovery. . 28 . 28 . 29 . 30 ~ 30 . 49 . 53 . 61 CHAPTER V APPLICATION AND IMPLEMENTATION. Waste Stream Balance. . . Collection Equipment Implementation of Source... Factor A. . 71 Materials Value Versus Compost Valu Factor B. . 74 LIST OF PLATES Plate Page Water-wall Incinerator Schematic. ~ ~ 33 Nodular Incinerator Schematic. . . 34 RDF Process Flowchart ~ ~ 35 Pyrolysis Process Schematic. 50 Pyrolysis...

Fiedler, Charles Walter

1982-01-01T23:59:59.000Z

113

Resource recovery potential from secondary components of segregated municipal solid wastes  

E-Print Network (OSTI)

(MSW) such as fruit and vegetable wastes (FVW), leaf litter, paddy straw, cane bagasse, cane trash for decentralized biogas plants to be operated in the vicinity. We characterized the fermen- tation potential of six of the above MSW fractions for their suitability to be converted to biogas and anaerobic compost using

Columbia University

114

Generation, storage, collection and transportation of municipal solid waste - A case study in the city of Kathmandu, capital of Nepal  

SciTech Connect

Solid waste management (SWM) services have consistently failed to keep up with the vast amount of solid waste produced in urban areas. There is not currently an efficient system in place for the management, storage, collection, and transportation of solid waste. Kathmandu City, an important urban center of South Asia, is no exception. In Kathmandu Metropolitan City, solid waste generation is predicted to be 1091 m{sup 3}/d (245 tons/day) and 1155 m{sup 3}/d (260 tons/day) for the years 2005 and 2006, respectively. The majority (89%) of households in Kathmandu Metropolitan City are willing to segregate the organic and non-organic portions of their waste. Overall collection efficiency was 94% in 2003. An increase in waste collection occurred due to private sector involvement, the shutdown of the second transfer station near the airport due to local protest, a lack of funding to maintain trucks/equipment, a huge increase in plastic waste, and the willingness of people to separate their waste into separate bins. Despite a substantial increase in total expenditure, no additional investments were made to the existing development plan to introduce a modern disposal system due to insufficient funding. Due to the lack of a proper lining, raw solid waste from the existing dumping site comes in contact with river water directly, causing severe river contamination and deteriorating the quality of the water.

Alam, R. [Shahjalal University of Science and Technology, Department of Civil and Environmental Engineering, Sylhet 3114 (Bangladesh)], E-mail: rakib_env@yahoo.com; Chowdhury, M.A.I.; Hasan, G.M.J.; Karanjit, B.; Shrestha, L.R. [Shahjalal University of Science and Technology, Department of Civil and Environmental Engineering, Sylhet 3114 (Bangladesh)

2008-07-01T23:59:59.000Z

115

Ranking municipal solid waste treatment alternatives considering sustainability criteria using the analytical hierarchical process tool  

Science Journals Connector (OSTI)

Abstract The establishment of an integrated rational waste management system is a complex issue, which has to be clearly investigated and a widespread variety of environmental, social and economic criteria should be taken into consideration. Each different waste treatment alternative provides a specific environmental, social and economic performance. Therefore, the crucial environmental, social and economic criteria need to be identified, estimated and thoroughly examined. In this manuscript, mechanical biological aerobic treatment without RDF energy recovery, mechanical biological anaerobic treatment and incineration with energy recovery are compared and finally ranked according to their environmental, social and economic performance. Analytical hierarchical process was used to rank the performance in three examined pillars in the capacity range of 70–90 kt. Incineration with energy recovery provides best performance due to the high amount of generated energy, whereas the other two options provide less capital costs. However, the performance of each treatment alternative is strongly dependent on the selection and weight of criteria.

I.-S. Antonopoulos; G. Perkoulidis; D. Logothetis; C. Karkanias

2014-01-01T23:59:59.000Z

116

Preliminary characterization of deposits formed on super heater surfaces in an FBC-boiler fired with municipal solid waste  

SciTech Connect

A preliminary study of the chemical and mineralogical composition of deposits formed on super heater tubes in a CFB fired with 100% sorted municipal solid waste has been carried out. Samples of deposits formed on both the windward and leeward side of the tubes were analyzed with the aim to identify the ash species involved in fouling and to get information about chemical interaction between the tube alloys and the deposits. The metal temperatures in the super heater region were in the range 460--540 C during the sampling period. The identified deposit constituents show the importance of alkali metal chlorides in the deposit forming process. Alkali metal chlorides (NaCl and KCl) were found both on the windward side deposits and on the leeward side. Other components were CaSO{sub 4}m MgO and some oxide and phosphate compounds. Some of these components have probably been formed through reaction between the alloy and the deposit but more work will be done in co-operation with the Competence Centre for High Temperature Corrosion, Sweden in order to elucidate such interactions and the influence of deposits on the corrosion rates. The presence of chlorides on an alloyed steel at the temperatures used here may cause a rapid deterioration of the protective oxide scale on the alloy. First, a layer of molten chlorides may dissolve species from the protective oxide layer on the steel tube. Secondly, corrosion may occur according to a mechanism called active oxidation, which involves diffusion of chlorine to the metal/oxide interface and breakdown of the scale due to formation of new products.

Steenari, B.M.; Lindqvist, O.; Andersson, B.A.

1999-07-01T23:59:59.000Z

117

Municipal solid waste combustion: Waste-to-energy technologies, regulations, and modern facilities in USEPA Region V  

SciTech Connect

Table of Contents: Incinerator operations (Waste preprocessing, combustion, emissions characterization and emission control, process monitoring, heat recovery, and residual ash management); Waste-to-energy regulations (Permitting requirements and operating regulations on both state and Federal levels); Case studies of EPA Region V waste-to-energy facilities (Polk County, Minnesota; Jackson County, Michigan; La Crosse, Wisconsin; Kent County, Michigan; Elk River, Minnesota; Indianapolis, Indiana); Evaluation; and Conclusions.

Sullivan, P.M.; Hallenbeck, W.H.; Brenniman, G.R.

1993-08-01T23:59:59.000Z

118

Clean energy from municipal solid waste. Technical progress report number 3  

SciTech Connect

Development of the computer models for slurry carbonization have begun and were based upon the collected data (mass balances, yield, temperatures, and pressures) from the previous pilot plant campaigns. All computer models are being developed with Aspen`s SpeedUp{trademark} software. The primary flow sheet with major alternatives has been developed and the majority of equipment descriptions and models, cost algorithms, and baseline parameters have been input to SpeedUp. The remaining modeling parameters will be input in the next reporting period and the initial flow sheet skeleton and model will be completed. The computer models will focus on optimizing capital and operating costs, and evaluating alternative waste water recycling technologies. The weaknesses of the previous pilot plant data and the data required for design of the commercial demonstration facility were identified. The identified weaknesses of the existing data included mass balance precision and accuracy, reactor residence time control (i.e. reactor level control), reactor temperature variations, and air entrainment in the feed RDF slurry. To improve mass balance precision and accuracy, an alternative carbonization gas flow meter will be designed and installed on the pilot plant. EnerTech`s carbonization gas flow meter design has been submitted to the EERC for final approval. In addition, an appropriate number of feed RDF samples will be characterized for moisture content just prior to the next pilot plant run to estimate incoming moisture variation. A pumping test also will be performed with the feed RDF slurry to determine the amount of air entrainment with the feed slurry.

Klosky, M.

1996-01-05T23:59:59.000Z

119

Managing America`s solid waste  

SciTech Connect

This report presents an historical overview of the federal role in municipal solid waste management from 1965 to approximately 1995. Attention is focuses on the federal role in safeguarding public health, protecting the environment, and wisely using material and energy resources. It is hoped that this report will provide important background for future municipal solid waste research and development initiatives.

Not Available

1998-03-02T23:59:59.000Z

120

Solid Waste Management (Indiana) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Solid Waste Management (Indiana) Solid Waste Management (Indiana) Solid Waste Management (Indiana) < Back Eligibility Agricultural Commercial Industrial Investor-Owned Utility Local Government Municipal/Public Utility Rural Electric Cooperative State/Provincial Govt Utility Program Info State Indiana Program Type Environmental Regulations Provider Association of Indiana Solid Wastes Districts Inc. The state supports the implementation of source reduction, recycling, and other alternative solid waste management practices over incineration and land disposal. The Indiana Department of Environmental Management and the Indiana Solid Waste Management Board are tasked with planning and adopting rules and regulations governing solid waste management practices. Provisions pertaining to landfill management and expansion, permitting,

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Oxygen demand for the stabilization of the organic fraction of municipal solid waste in passively aerated bioreactors  

SciTech Connect

Highlights: • The use of an passively aerated reactor enables effective stabilization of OFMSW. • Convective air flow does not inhibit the aerobic stabilization of waste. • The use of an passively aerated reactor reduces the heat loss due to convection. • The volume of supplied air exceeds 1.7–2.88 times the microorganisms demand. - Abstract: Conventional aerobic waste treatment technologies require the use of aeration devices that actively transport air through the stabilized waste mass, which greatly increases operating costs. In addition, improperly operated active aeration systems, may have the adverse effect of cooling the stabilized biomass. Because active aeration can be a limiting factor for the stabilization process, passive aeration can be equally effective and less expensive. Unfortunately, there are few reports documenting the use of passive aeration systems in municipal waste stabilization. There have been doubts raised as to whether a passive aeration system provides enough oxygen to the organic matter mineralization processes. In this paper, the effectiveness of aeration during aerobic stabilization of four different organic fractions of municipal waste in a reactor with an integrated passive ventilation system and leachate recirculation was analyzed. For the study, four fractions separated by a rotary screen were chosen. Despite the high temperatures in the reactor, the air flow rate was below 0.016 m{sup 3}/h. Using Darcy’s equation, theoretical values of the air flow rate were estimated, depending on the intensity of microbial metabolism and the amount of oxygen required for the oxidation of organic compounds. Calculations showed that the volume of supplied air exceeded the microorganisms demand for oxidation and endogenous activity by 1.7–2.88-fold.

Kasinski, Slawomir, E-mail: slawomir.kasinski@uwm.edu.pl; Wojnowska-Baryla, Irena

2014-02-15T23:59:59.000Z

122

Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume 2: A Techno-economic Evaluation of the Production of Mixed Alcohols  

Energy.gov (U.S. Department of Energy (DOE))

Biomass is a renewable energy resource that can be converted into liquid fuel suitable for transportation applications and thus help meet the Energy Independence and Security Act renewable energy goals (U.S. Congress 2007). However, biomass is not always available in sufficient quantity at a price compatible with fuels production. Municipal solid waste (MSW) on the other hand is readily available in large quantities in some communities and is considered a partially renewable feedstock. Furthermore, MSW may be available for little or no cost.

123

The mathematical modelling of biomethane production and the growth of methanogenic bacteria in batch reactor systems fed with organic municipal solid waste  

Science Journals Connector (OSTI)

A mathematical model was developed and validated for an anaerobic digestion system of the Organic Fraction of Municipal Solid Wastes (OFMSWs) by using a laboratory-scale system of two Packed Bed Reactors (PBRs). The equations were obtained by the mass balances of methanogenic bacteria of affluent and effluent lixiviated, as well as the interior in each reactor. The methane rate was obtained by multiplying the methanogenic activity. A differential equation was fitted with experimental results to obtain the parameters that best describe methanogenic behaviour. These kinetic parameters were used with the modified logistic equation with the special case n = 1.

Liliana Alzate-Gaviria; Antonino Perez-Hernandez; Hector M. Poggi-Varaldo; P.J. Sebastian

2009-01-01T23:59:59.000Z

124

Solid Waste Regulation No. 8 - Solid Waste Composting Facilities (Rhode  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Regulation No. 8 - Solid Waste Composting Facilities Regulation No. 8 - Solid Waste Composting Facilities (Rhode Island) Solid Waste Regulation No. 8 - Solid Waste Composting Facilities (Rhode Island) < Back Eligibility Commercial Industrial Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Rhode Island Program Type Environmental Regulations Provider Department of Environmental Management Facilities which compost putrescible waste and/or leaf and yard waste are subject to these regulations. The regulations establish permitting, registration, and operational requirements for composting facilities. Operational requirements for putrescible waste facilities include siting, distance, and buffer requirements, as well as standards for avoiding harm to endangered species and contamination of air and water sources. Specific

125

E-Print Network 3.0 - asme solid waste Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Summary: -21, 2008, Philadelphia, Pennsylvania, USA NAWTEC16-1901 PLASMA ARC GASIFICATION FOR SOLID WASTE DISPOSAL... in municipal solid waste destruction since 1999 in...

126

Municipal Waste Planning, Recycling and Waste Reduction Act (Pennsylvania)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Municipal Waste Planning, Recycling and Waste Reduction Act Municipal Waste Planning, Recycling and Waste Reduction Act (Pennsylvania) Municipal Waste Planning, Recycling and Waste Reduction Act (Pennsylvania) < Back Eligibility Agricultural Commercial Construction Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Pennsylvania Program Type Environmental Regulations

127

Chemical pollution and toxicity of water samples from stream receiving leachate from controlled municipal solid waste (MSW) landfill  

Science Journals Connector (OSTI)

Abstract The present study was aimed to determine the impact of municipal waste landfill on the pollution level of surface waters, and to investigate whether the choice and number of physical and chemical parameters monitored are sufficient for determining the actual risk related to bioavailability and mobility of contaminants. In 2007–2012, water samples were collected from the stream flowing through the site at two sampling locations, i.e. before the stream?s entry to the landfill, and at the stream outlet from the landfill. The impact of leachate on the quality of stream water was observed in all samples. In 2007–2010, high values of TOC and conductivity in samples collected down the stream from the landfill were observed; the toxicity of these samples was much greater than that of samples collected up the stream from the landfill. In 2010–2012, a significant decrease of conductivity and TOC was observed, which may be related to the modernization of the landfill. Three tests were used to evaluate the toxicity of sampled water. As a novelty the application of Phytotoxkit F™ for determining water toxicity should be considered. Microtox® showed the lowest sensitivity of evaluating the toxicity of water samples, while Phytotoxkit F™ showed the highest. High mortality rates of Thamnocephalus platyurus in Thamnotoxkit F™ test can be caused by high conductivity, high concentration of TOC or the presence of compounds which are not accounted for in the water quality monitoring program.

A. Melnyk; K. Kukli?ska; L. Wolska; J. Namie?nik

2014-01-01T23:59:59.000Z

128

Anaerobic digestion of organic solid waste for energy production.  

E-Print Network (OSTI)

??This study was carried out in order to evaluate the performance of anaerobic reactors treating OFMSW (organic fraction of municipal solid waste), especially in terms… (more)

Nayono, Satoto Endar

2009-01-01T23:59:59.000Z

129

Overburden effects on waste compaction and leachate generation in municipal landfills  

E-Print Network (OSTI)

This thesis presents a model to predict the effects of overburden pressure on the formation of leachate within municipal solid waste landfills. In addition, it estimates the compaction and subsequent settlement that the waste will undergo due...

Mehevec, Adam Wade

2012-06-07T23:59:59.000Z

130

Solid-State Lighting: 2010 Municipal Consortium Southwest Region Workshop  

NLE Websites -- All DOE Office Websites (Extended Search)

0 Municipal Consortium 0 Municipal Consortium Southwest Region Workshop Materials to someone by E-mail Share Solid-State Lighting: 2010 Municipal Consortium Southwest Region Workshop Materials on Facebook Tweet about Solid-State Lighting: 2010 Municipal Consortium Southwest Region Workshop Materials on Twitter Bookmark Solid-State Lighting: 2010 Municipal Consortium Southwest Region Workshop Materials on Google Bookmark Solid-State Lighting: 2010 Municipal Consortium Southwest Region Workshop Materials on Delicious Rank Solid-State Lighting: 2010 Municipal Consortium Southwest Region Workshop Materials on Digg Find More places to share Solid-State Lighting: 2010 Municipal Consortium Southwest Region Workshop Materials on AddThis.com... Conferences & Meetings Presentations Publications

131

Solid-State Lighting: 2011 Municipal Consortium Southeast Region Workshop  

NLE Websites -- All DOE Office Websites (Extended Search)

1 Municipal Consortium 1 Municipal Consortium Southeast Region Workshop Materials to someone by E-mail Share Solid-State Lighting: 2011 Municipal Consortium Southeast Region Workshop Materials on Facebook Tweet about Solid-State Lighting: 2011 Municipal Consortium Southeast Region Workshop Materials on Twitter Bookmark Solid-State Lighting: 2011 Municipal Consortium Southeast Region Workshop Materials on Google Bookmark Solid-State Lighting: 2011 Municipal Consortium Southeast Region Workshop Materials on Delicious Rank Solid-State Lighting: 2011 Municipal Consortium Southeast Region Workshop Materials on Digg Find More places to share Solid-State Lighting: 2011 Municipal Consortium Southeast Region Workshop Materials on AddThis.com... Conferences & Meetings Presentations Publications

132

Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume 2: A Techno-economic Evaluation of the Production of Mixed Alcohols  

SciTech Connect

Biomass is a renewable energy resource that can be converted into liquid fuel suitable for transportation applications and thus help meet the Energy Independence and Security Act renewable energy goals (U.S. Congress 2007). However, biomass is not always available in sufficient quantity at a price compatible with fuels production. Municipal solid waste (MSW) on the other hand is readily available in large quantities in some communities and is considered a partially renewable feedstock. Furthermore, MSW may be available for little or no cost. This report provides a techno-economic analysis of the production of mixed alcohols from MSW and compares it to the costs for a wood based plant. In this analysis, MSW is processed into refuse derived fuel (RDF) and then gasified in a plant co-located with a landfill. The resulting syngas is then catalytically converted to mixed alcohols. At a scale of 2000 metric tons per day of RDF, and using current technology, the minimum ethanol selling price at a 10% rate of return is approximately $1.85/gallon ethanol (early 2008 $). However, favorable economics are dependent upon the toxicity characteristics of the waste streams and that a market exists for the by-product scrap metal recovered from the RDF process.

Jones, Susanne B.; Zhu, Yunhua; Valkenburt, Corinne

2009-05-01T23:59:59.000Z

133

Solid Waste Management (Kansas) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Solid Waste Management (Kansas) Solid Waste Management (Kansas) Solid Waste Management (Kansas) < Back Eligibility Commercial Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Kansas Program Type Environmental Regulations Provider Health and Environment This act aims to establish and maintain a cooperative state and local program of planning and technical and financial assistance for comprehensive solid waste management. No person shall construct, alter or operate a solid waste processing facility or a solid waste disposal area of a solid waste management system, except for clean rubble disposal sites, without first obtaining a permit from the secretary. Every person desiring to obtain a permit shall make application for such a permit on forms

134

Management of Solid Waste (Oklahoma) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Management of Solid Waste (Oklahoma) Management of Solid Waste (Oklahoma) Management of Solid Waste (Oklahoma) < Back Eligibility Utility Agricultural Investor-Owned Utility Industrial Municipal/Public Utility Rural Electric Cooperative Program Info State Oklahoma Program Type Environmental Regulations Provider Oklahoma Department of Environmental Quality The Solid Waste Management Division of the Department of Environmental Quality regulates solid waste disposal or any person who generates, collects, transports, processes, and/or disposes of solid waste and/or waste tires. The following solid waste disposal facilities require a solid waste permit prior to construction and/or operation: land disposal facilities; solid waste processing facilities, including: transfer stations; solid waste incinerators receiving waste from off-site sources; regulated medical waste

135

Parameters affecting the stability of the digestate from a two-stage anaerobic process treating the organic fraction of municipal solid waste  

SciTech Connect

This paper focused on the factors affecting the respiration rate of the digestate taken from a continuous anaerobic two-stage process treating the organic fraction of municipal solid waste (OFMSW). The process involved a hydrolytic reactor (HR) that produced a leachate fed to a submerged anaerobic membrane bioreactor (SAMBR). It was found that a volatile solids (VS) removal in the range 40-75% and an operating temperature in the HR between 21 and 35 {sup o}C resulted in digestates with similar respiration rates, with all digestates requiring 17 days of aeration before satisfying the British Standard Institution stability threshold of 16 mg CO{sub 2} g VS{sup -1} day{sup -1}. Sanitization of the digestate at 65 {sup o}C for 7 days allowed a mature digestate to be obtained. At 4 g VS L{sup -1} d{sup -1} and Solid Retention Times (SRT) greater than 70 days, all the digestates emitted CO{sub 2} at a rate lower than 25 mg CO{sub 2} g VS{sup -1} d{sup -1} after 3 days of aeration, while at SRT lower than 20 days all the digestates displayed a respiration rate greater than 25 mg CO{sub 2} g VS{sup -1} d{sup -1}. The compliance criteria for Class I digestate set by the European Commission (EC) and British Standard Institution (BSI) could not be met because of nickel and chromium contamination, which was probably due to attrition of the stainless steel stirrer in the HR.

Trzcinski, Antoine P., E-mail: a.trzcinski05@ic.ac.uk [Department of Chemical Engineering, Imperial College of Science and Technology and Medicine, Prince Consort Road, London SW7 2AZ (United Kingdom); Stuckey, David C., E-mail: d.stuckey@ic.ac.uk [Department of Chemical Engineering, Imperial College of Science and Technology and Medicine, Prince Consort Road, London SW7 2AZ (United Kingdom)

2011-07-15T23:59:59.000Z

136

Biomonitoring of the genotoxic potential of aqueous extracts of soils and bottom ash resulting from municipal solid waste  

E-Print Network (OSTI)

wastes and contaminated sites is an important economic and environmental problem. The regula- tions, France Abstract The management of contaminated soils and wastes is a matter of considerable human concern (Xenopus laevis). Soil A was contaminated by residues of solvents and metals and Soil B by polycyclic

Mailhes, Corinne

137

Solid Waste and Infectious Waste Regulations (Ohio) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Infectious Waste Regulations (Ohio) and Infectious Waste Regulations (Ohio) Solid Waste and Infectious Waste Regulations (Ohio) < Back Eligibility Utility Agricultural Investor-Owned Utility Industrial Municipal/Public Utility Local Government Rural Electric Cooperative Program Info State Ohio Program Type Environmental Regulations Provider Ohio Environmental Protection Agency This chapter of the law that establishes the Ohio Environmental Protection Agency establishes the rules and regulations regarding solid waste. The chapter establishes specific regulations for biomass facilities, which includes permitting, siting, operation, safety guidelines, and closing requirements. Siting regulations include setbacks from waste handling areas for state facilities (1000 feet from jails, schools), requirements for not siting

138

Guide to Clean Development Mechanism Projects Related to Municipal Solid  

Open Energy Info (EERE)

Guide to Clean Development Mechanism Projects Related to Municipal Solid Guide to Clean Development Mechanism Projects Related to Municipal Solid Waste Management Jump to: navigation, search Tool Summary Name: A Guide to Clean Development Mechanism Projects Related to Municipal Solid Waste Management Agency/Company /Organization: United Nations Economic and Social Commission for Asia and the Pacific Sector: Energy, Land Focus Area: - Landfill Gas, - Waste to Energy Topics: Implementation, Co-benefits assessment Resource Type: Guide/manual, Lessons learned/best practices Website: www.unescap.org/esd/environment/publications/cdm/Guide.pdf UN Region: Central Asia, Eastern Asia, South-Eastern Asia, "Pacific" is not in the list of possible values (Eastern Africa, Middle Africa, Northern Africa, Southern Africa, Western Africa, Caribbean, Central America, South America, Northern America, Central Asia, Eastern Asia, Southern Asia, South-Eastern Asia, Western Asia, Eastern Europe, Northern Europe, Southern Europe, Western Europe, Australia and New Zealand, Melanesia, Micronesia, Polynesia, Latin America and the Caribbean) for this property.

139

Mercury emissions from municipal solid waste combustors. An assessment of the current situation in the United States and forecast of future emissions  

SciTech Connect

This report examines emissions of mercury (Hg) from municipal solid waste (MSW) combustion in the United States (US). It is projected that total annual nationwide MSW combustor emissions of mercury could decrease from about 97 tonnes (1989 baseline uncontrolled emissions) to less than about 4 tonnes in the year 2000. This represents approximately a 95 percent reduction in the amount of mercury emitted from combusted MSW compared to the 1989 mercury emissions baseline. The likelihood that routinely achievable mercury emissions removal efficiencies of about 80 percent or more can be assured; it is estimated that MSW combustors in the US could prove to be a comparatively minor source of mercury emissions after about 1995. This forecast assumes that diligent measures to control mercury emissions, such as via use of supplemental control technologies (e.g., carbon adsorption), are generally employed at that time. However, no present consensus was found that such emissions control measures can be implemented industry-wide in the US within this time frame. Although the availability of technology is apparently not a limiting factor, practical implementation of necessary control technology may be limited by administrative constraints and other considerations (e.g., planning, budgeting, regulatory compliance requirements, etc.). These projections assume that: (a) about 80 percent mercury emissions reduction control efficiency is achieved with air pollution control equipment likely to be employed by that time; (b) most cylinder-shaped mercury-zinc (CSMZ) batteries used in hospital applications can be prevented from being disposed into the MSW stream or are replaced with alternative batteries that do not contain mercury; and (c) either the amount of mercury used in fluorescent lamps is decreased to an industry-wide average of about 27 milligrams of mercury per lamp or extensive diversion from the MSW stream of fluorescent lamps that contain mercury is accomplished.

none,

1993-05-01T23:59:59.000Z

140

Design Case Summary: Production of Mixed Alcohols from Municipal...  

Office of Environmental Management (EM)

Design Case Summary: Production of Mixed Alcohols from Municipal Solid Waste via Gasification Design Case Summary: Production of Mixed Alcohols from Municipal Solid Waste via...

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Capacity-to-Act in India's Solid Waste Management and Waste-to-  

E-Print Network (OSTI)

, for example, Oppili, P., "Waste Burning, A Health Hazard at Pallikaranai," The Hindu, Sept. 9, 2003; "MPPCB1 Capacity-to-Act in India's Solid Waste Management and Waste-to- Energy Industries Perinaz Bhada and disposal of garbage, or municipal solid waste, compounded by increasing consumption levels. Another serious

Columbia University

142

Louisiana Solid Waste Management and Resource Recovery Law (Louisiana) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Louisiana Solid Waste Management and Resource Recovery Law Louisiana Solid Waste Management and Resource Recovery Law (Louisiana) Louisiana Solid Waste Management and Resource Recovery Law (Louisiana) < Back Eligibility Agricultural Construction Developer Industrial Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Louisiana Program Type Environmental Regulations Provider Louisiana Department of Environmental Quality The Louisiana Department of Environmental Quality manages solid waste for the state of Louisiana under the authority of the Solid Waste Management and Resource Recover Law. The Department makes rules and regulations that establish standards governing the storage, collection, processing, recovery and reuse, and disposal of solid waste; implement a management program that

143

Status report on energy recovery from municipal solid waste: technologies, lessons and issues. Information bulletin of the energy task force of the urban consortium  

SciTech Connect

A review is presented of the lessons learned and issues raised regarding the recovery of energy from solid wastes. The review focuses on technologies and issues significant to currently operating energy recovery systems in the US - waterwall incineration, modular incineration, refuse derived fuels systems, landfill gas recovery systems. Chapters are: Energy Recovery and Solid Waste Disposal; Energy Recovery Systems; Lessons in Energy Recovery; Issues in Energy Recovery. Some basic conclusions are presented concerning the state of the art of energy from waste. Plants in shakedown or under construction, along with technologies in the development stages, are briefly described. Sources of additional information and a bibliography are included. (MCW)

None

1980-01-01T23:59:59.000Z

144

Solid Waste Policies (Iowa) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Policies (Iowa) Policies (Iowa) Solid Waste Policies (Iowa) < Back Eligibility Agricultural Commercial Fuel Distributor Industrial Investor-Owned Utility Local Government Municipal/Public Utility Rural Electric Cooperative Tribal Government Utility Program Info State Iowa Program Type Environmental Regulations Provider Iowa Department of Natural Resources This statute establishes the support of the state for alternative waste management practices that reduce the reliance upon land disposal and incorporate resource recovery. Cities and counties are required to establish and operate a comprehensive solid waste reduction program. These regulations discuss land application of processed wastes as well as requirements for sanitary landfills and for groundwater monitoring near land disposal sites

145

Solid-State Lighting: 2011 Municipal Consortium North Central Region  

NLE Websites -- All DOE Office Websites (Extended Search)

2011 Municipal Consortium North 2011 Municipal Consortium North Central Region Workshop Materials to someone by E-mail Share Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Facebook Tweet about Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Twitter Bookmark Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Google Bookmark Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Delicious Rank Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Digg Find More places to share Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on AddThis.com... Conferences & Meetings

146

A Full-scale Study on the Partitioning of Trace Elements in Municipal Solid Waste Incineration—Effects of Firing Different Waste Types  

Science Journals Connector (OSTI)

The changes in waste composition were applied by adding (one-by-one): dedicated waste fractions, comprising road salt (NaCl), household batteries, automotive shredder waste, CCA (copper?chromate?arsenate)-impregnated wood, PVC, and, shoes, to a base-load waste. ... What is left after removing recyclables from vehicles is shredded. ... Automotive shredder waste (residues) is then the light shredder fraction from the airflow separator that separates it from the heavier metallic fraction, which is fully recyclable as a secondary raw material. ...

Anne J. Pedersen; Flemming J. Frandsen; Christian Riber; Thomas Astrup; Sřren N. Thomsen; Kasper Lundtorp; Leif F. Mortensen

2009-03-23T23:59:59.000Z

147

Solid-State Lighting: Text-Alternative Version: Municipal Solid-State  

NLE Websites -- All DOE Office Websites (Extended Search)

Municipal Solid-State Street Lighting Consortium Kickoff to someone by Municipal Solid-State Street Lighting Consortium Kickoff to someone by E-mail Share Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Kickoff on Facebook Tweet about Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Kickoff on Twitter Bookmark Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Kickoff on Google Bookmark Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Kickoff on Delicious Rank Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Kickoff on Digg Find More places to share Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Kickoff on

148

Solid-State Lighting: Municipal Solid-State Street Lighting Consortium  

NLE Websites -- All DOE Office Websites (Extended Search)

Municipal Solid-State Street Municipal Solid-State Street Lighting Consortium Kickoff Webcast to someone by E-mail Share Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Facebook Tweet about Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Twitter Bookmark Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Google Bookmark Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Delicious Rank Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Digg Find More places to share Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on AddThis.com... Conferences & Meetings

149

Solid Waste Rules (New Hampshire)  

Energy.gov (U.S. Department of Energy (DOE))

The solid waste statute applies to construction and demolition debris, appliances, recyclables, and the facilities that collect, process, and dispose of solid waste. DES oversees the management of...

150

Solid Waste Management (North Carolina)  

Energy.gov (U.S. Department of Energy (DOE))

The Solid Waste Program regulates safe management of solid waste through guidance, technical assistance, regulations, permitting, environmental monitoring, compliance evaluation and enforcement....

151

Municipal Waste Planning, Recycling and Waste Reduction Act (Pennsylvania)  

Open Energy Info (EERE)

Waste Planning, Recycling and Waste Reduction Act (Pennsylvania) Waste Planning, Recycling and Waste Reduction Act (Pennsylvania) No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Last modified on February 13, 2013. EZFeed Policy Place Pennsylvania Name Municipal Waste Planning, Recycling and Waste Reduction Act (Pennsylvania) Policy Category Other Policy Policy Type Environmental Regulations Affected Technologies Biomass/Biogas, Coal with CCS, Concentrating Solar Power, Energy Storage, Fuel Cells, Geothermal Electric, Hydroelectric, Hydroelectric (Small), Natural Gas, Nuclear, Solar Photovoltaics, Wind energy Active Policy Yes Implementing Sector State/Province Program Administrator Pennsylvania Department of Environmental Protection

152

Chapter 47 Solid Waste Facilities (Kentucky) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Chapter 47 Solid Waste Facilities (Kentucky) Chapter 47 Solid Waste Facilities (Kentucky) Chapter 47 Solid Waste Facilities (Kentucky) < Back Eligibility Agricultural Commercial Construction Developer Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Program Info State Kentucky Program Type Environmental Regulations Fees Siting and Permitting Provider Kentucky Division of Waste Management This chapter establishes the permitting standards for solid waste sites or facilities, the standards applicable to all solid waste sites or

153

The effect of changing waste compositions on the incineration process of Municipal Solid Wastes in packed-bed systems: a CFD approach  

Science Journals Connector (OSTI)

With the recent changes in waste management policy across many EU countries, more and more efforts are now being made on wastes recycling and minimisation. In this paper, the effects of the changing compositions of wastes on the operation of incineration plants are addressed. CFD technique is used to simulate the incineration processes in grate systems and advanced mathematical models are employed. The incineration characteristics have been expressed as functions of the percentage of combustible materials in wastes taken away for recycling. To offset the deteriorated performance of incineration in some cases, alternative operation modes have been suggested and simulated.

Yao Bin Yang; Vida N. Sharifi; Jim Swithenbank

2007-01-01T23:59:59.000Z

154

Solid Waste Disposal, Hazardous Waste Management Act, Underground Storage  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Disposal, Hazardous Waste Management Act, Underground Disposal, Hazardous Waste Management Act, Underground Storage Act (Tennessee) Solid Waste Disposal, Hazardous Waste Management Act, Underground Storage Act (Tennessee) < Back Eligibility Agricultural Commercial Construction Developer Fuel Distributor Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Municipal/Public Utility Nonprofit Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Tribal Government Utility Program Info State Tennessee Program Type Environmental Regulations Siting and Permitting Provider Tennessee Department Of Environment and Conservation The Solid Waste Disposal Laws and Regulations are found in Tenn. Code 68-211. These rules are enforced and subject to change by the Public Waste Board (PWB), which is established by the Division of Solid and Hazardous

155

Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium  

NLE Websites -- All DOE Office Websites (Extended Search)

Market-Based Programs Printable Version Share this resource Send a link to Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium to someone by E-mail Share Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Facebook Tweet about Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Twitter Bookmark Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Google Bookmark Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Delicious Rank Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Digg Find More places to share Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on AddThis.com... LED Lighting Facts

156

Energy utilization: municipal waste incineration. Final report  

SciTech Connect

An assessment is made of the technical and economical feasibility of converting municipal waste into useful and useable energy. The concept presented involves retrofitting an existing municipal incinerator with the systems and equipment necessary to produce process steam and electric power. The concept is economically attractive since the cost of necessary waste heat recovery equipment is usually a comparatively small percentage of the cost of the original incinerator installation. Technical data obtained from presently operating incinerators designed specifically for generating energy, documents the technical feasibility and stipulates certain design constraints. The investigation includes a cost summary; description of process and facilities; conceptual design; economic analysis; derivation of costs; itemized estimated costs; design and construction schedule; and some drawings.

LaBeck, M.F.

1981-03-27T23:59:59.000Z

157

Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting  

NLE Websites -- All DOE Office Websites (Extended Search)

Webcast: Municipal Solid-State Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool to someone by E-mail Share Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Facebook Tweet about Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Twitter Bookmark Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Google Bookmark Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Delicious Rank Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Digg

158

Solid-State Lighting: 2011 Municipal Consortium North Central Region  

NLE Websites -- All DOE Office Websites (Extended Search)

Consortium North Consortium North Central Region Workshop Materials to someone by E-mail Share Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Facebook Tweet about Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Twitter Bookmark Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Google Bookmark Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Delicious Rank Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on Digg Find More places to share Solid-State Lighting: 2011 Municipal Consortium North Central Region Workshop Materials on AddThis.com... LED Lighting Facts CALiPER Program

159

Solid-State Lighting: 2011 Municipal Consortium Northeast Region Workshop  

NLE Websites -- All DOE Office Websites (Extended Search)

Northeast Region Workshop Materials to someone by E-mail Northeast Region Workshop Materials to someone by E-mail Share Solid-State Lighting: 2011 Municipal Consortium Northeast Region Workshop Materials on Facebook Tweet about Solid-State Lighting: 2011 Municipal Consortium Northeast Region Workshop Materials on Twitter Bookmark Solid-State Lighting: 2011 Municipal Consortium Northeast Region Workshop Materials on Google Bookmark Solid-State Lighting: 2011 Municipal Consortium Northeast Region Workshop Materials on Delicious Rank Solid-State Lighting: 2011 Municipal Consortium Northeast Region Workshop Materials on Digg Find More places to share Solid-State Lighting: 2011 Municipal Consortium Northeast Region Workshop Materials on AddThis.com... LED Lighting Facts CALiPER Program Standards Development Technical Information Network

160

Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop  

NLE Websites -- All DOE Office Websites (Extended Search)

Los Angeles, CA to someone Los Angeles, CA to someone by E-mail Share Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Facebook Tweet about Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Twitter Bookmark Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Google Bookmark Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Delicious Rank Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Digg Find More places to share Solid-State Lighting: Municipal Consortium

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Solid-State Lighting: Municipal Consortium Annual Meeting Presentations and  

NLE Websites -- All DOE Office Websites (Extended Search)

Information Information Resources Printable Version Share this resource Send a link to Solid-State Lighting: Municipal Consortium Annual Meeting Presentations and Materials-Phoenix, AZ to someone by E-mail Share Solid-State Lighting: Municipal Consortium Annual Meeting Presentations and Materials-Phoenix, AZ on Facebook Tweet about Solid-State Lighting: Municipal Consortium Annual Meeting Presentations and Materials-Phoenix, AZ on Twitter Bookmark Solid-State Lighting: Municipal Consortium Annual Meeting Presentations and Materials-Phoenix, AZ on Google Bookmark Solid-State Lighting: Municipal Consortium Annual Meeting Presentations and Materials-Phoenix, AZ on Delicious Rank Solid-State Lighting: Municipal Consortium Annual Meeting Presentations and Materials-Phoenix, AZ on Digg

162

Solid-State Lighting: 2011 Municipal Consortium Northwest Region Workshop  

NLE Websites -- All DOE Office Websites (Extended Search)

Northwest Region Workshop Materials to someone by E-mail Northwest Region Workshop Materials to someone by E-mail Share Solid-State Lighting: 2011 Municipal Consortium Northwest Region Workshop Materials on Facebook Tweet about Solid-State Lighting: 2011 Municipal Consortium Northwest Region Workshop Materials on Twitter Bookmark Solid-State Lighting: 2011 Municipal Consortium Northwest Region Workshop Materials on Google Bookmark Solid-State Lighting: 2011 Municipal Consortium Northwest Region Workshop Materials on Delicious Rank Solid-State Lighting: 2011 Municipal Consortium Northwest Region Workshop Materials on Digg Find More places to share Solid-State Lighting: 2011 Municipal Consortium Northwest Region Workshop Materials on AddThis.com... LED Lighting Facts CALiPER Program Standards Development Technical Information Network

163

Report No. PA 14 of 2008 Compliance to rules governing municipal solid, bio-medical and plastic  

E-Print Network (OSTI)

-medical and plastic waste Objective 5: Whether effective compliance to rules/laws regulating municipal solid waste, bio-medical waste and plastic waste was taking place in the state. The United Nations Conference of 2008 54 · The Recycled Plastics Manufacture and Usage Rules were notified in 1999 with an amendment

Columbia University

164

Integrated solid waste management of Minneapolis, Minnesota  

SciTech Connect

The subject document reports the results of an in-depth investigation of the fiscal year 1992 cost of the City of Minneapolis, Minnesota (Hennepin County) integrated municipal solid waste management (IMSWM) system, the energy consumed to operate the system, and the environmental performance requirements for each of the system`s waste-processing and disposal facilities. Actual data from records kept by participants is reported in this document. Every effort was made to minimize the use of assumptions, and no attempt is made to interpret the data reported. Analytical approaches are documented so that interested analysts may perform manipulation or further analysis of the data. As such, the report is a reference document for municipal solid waste (MSW) management professionals who are interested in the actual costs and energy consumption for a one-year period, of an operating IMSWM system.

NONE

1995-11-01T23:59:59.000Z

165

Solid Waste Facilities Regulations (Massachusetts) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Solid Waste Facilities Regulations (Massachusetts) Solid Waste Facilities Regulations (Massachusetts) Solid Waste Facilities Regulations (Massachusetts) < Back Eligibility Agricultural Commercial Construction Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Program Info State Massachusetts Program Type Environmental Regulations Provider Department of Environmental Protection This chapter of the Massachusetts General Laws governs the operation of solid waste facilities. It seeks to encourage sustainable waste management

166

E-Print Network 3.0 - antimony sbfrom municipal Sample Search...  

NLE Websites -- All DOE Office Websites (Extended Search)

municipal... solid waste in a municipal waste combustor (MWC). In an attempt to "turn the tide", officials from Polk Source: Columbia University - Waste-to-Energy Research and...

167

Solid Waste Management (Michigan) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Michigan) Michigan) Solid Waste Management (Michigan) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Program Info State Michigan Program Type Siting and Permitting Provider Department of Environmental Quality This Act encourages the Department of Environmental Quality and Health Department representatives to develop and encourage methods for disposing solid waste that are environmentally sound, that maximize the utilization

168

Solid Waste Management (Connecticut) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Connecticut) Connecticut) Solid Waste Management (Connecticut) < Back Eligibility Agricultural Commercial Construction Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Program Info State Connecticut Program Type Siting and Permitting Provider Department of Energy and Environmental Protection Solid waste facilities operating in Connecticut must abide by these regulations, which describe requirements and procedures for issuing construction and operating permits; environmental considerations;

169

On the effect of demographic characteristics on the formulation of solid waste charging policy  

E-Print Network (OSTI)

On the effect of demographic characteristics on the formulation of solid waste charging policy A. Karagiannidis *, A. Xirogiannopoulou, N. Moussiopoulos Laboratory of Heat Transfer and Environmental Engineering of municipal charges in Greece, as the fees paid by municipal waste producers to the municipal authorities

Columbia University

170

Delaware Solid Waste Authority (Delaware)  

Energy.gov (U.S. Department of Energy (DOE))

The Delaware Solid Waste Authority (DSWA) runs three landfills, all of which recover methane and generate electricity with a total capacity of 24 MWs. The DSWA Solid Waste Plan includes goals,...

171

Solid-State Lighting: Text-Alternative Version: Municipal Solid-State  

NLE Websites -- All DOE Office Websites (Extended Search)

Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool Webcast to someone by E-mail Share Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool Webcast on Facebook Tweet about Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool Webcast on Twitter Bookmark Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool Webcast on Google Bookmark Solid-State Lighting: Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool Webcast on Delicious Rank Solid-State Lighting: Text-Alternative Version: Municipal

172

Solid Waste Management Act (Oklahoma) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here You are here Home » Solid Waste Management Act (Oklahoma) Solid Waste Management Act (Oklahoma) < Back Eligibility Agricultural Commercial Construction Industrial Installer/Contractor Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Oklahoma Program Type Environmental Regulations Provider Oklahoma Department of Environmental Quality This Act establishes rules for the permitting, posting of security, construction, operation, closure, maintenance and remediation of solid waste disposal sites; disposal of solid waste in ways that are environmentally safe and sanitary, as well as economically feasible; submission of laboratory reports or analyses performed by certified laboratories for the purposes of compliance monitoring and testing and for

173

Solid Waste Disposal Facilities (Massachusetts) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Solid Waste Disposal Facilities (Massachusetts) Solid Waste Disposal Facilities (Massachusetts) Solid Waste Disposal Facilities (Massachusetts) < Back Eligibility Agricultural Commercial Construction Fed. Government Fuel Distributor Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Municipal/Public Utility Rural Electric Cooperative State/Provincial Govt Transportation Tribal Government Utility Program Info State Massachusetts Program Type Siting and Permitting Provider Department of Environmental Protection These sections articulate rules for the maintenance and operation of solid waste disposal facilities, as well as site assignment procedures. Applications for site assignment will be reviewed by the Massachusetts Department of Environmental Protection as well as the Department of Public

174

Best Practices for Siting Solar Photovoltaics on Municipal Solid Waste Landfills. A Study Prepared in Partnership with the Environmental Protection Agency for the RE-Powering America's Land Initiative: Siting Renewable Energy on Potentially Contaminated Land and Mine Sites  

SciTech Connect

The Environmental Protection Agency and the National Renewable Energy Laboratory developed this best practices document to address common technical challenges for siting solar photovoltaics (PV) on municipal solid waste (MSW) landfills. The purpose of this document is to promote the use of MSW landfills for solar energy systems. Closed landfills and portions of active landfills with closed cells represent thousands of acres of property that may be suitable for siting solar photovoltaics (PV). These closed landfills may be suitable for near-term construction, making these sites strong candidate to take advantage of the 30% Federal Business Energy Investment Tax Credit. It was prepared in response to the increasing interest in siting renewable energy on landfills from solar developers; landfill owners; and federal, state, and local governments. It contains examples of solar PV projects on landfills and technical considerations and best practices that were gathered from examining the implementation of several of these projects.

Kiatreungwattana, K.; Mosey, G.; Jones-Johnson, S.; Dufficy, C.; Bourg, J.; Conroy, A.; Keenan, M.; Michaud, W.; Brown, K.

2013-04-01T23:59:59.000Z

175

Gaines County Solid Waste Management Act (Texas) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Gaines County Solid Waste Management Act (Texas) Gaines County Solid Waste Management Act (Texas) Gaines County Solid Waste Management Act (Texas) < Back Eligibility Commercial Construction Industrial Investor-Owned Utility Local Government Municipal/Public Utility Rural Electric Cooperative Tribal Government Utility Program Info State Texas Program Type Environmental Regulations Provider Gaines County Solid Waste Management District This Act establishes the Gaines County Solid Waste Management District, a governmental body to develop and carry out a regional water quality protection program through solid waste management and regulation of waste disposal. The District has the power to prepare, adopt plans for, purchase, obtain permits for, construct, acquire, own, operate, maintain, repair, improve, and extend inside and outside the boundaries of the district any works,

176

International Best Practices for Pre-Processing and Co-Processing Municipal Solid Waste and Sewage Sludge in the Cement Industry  

E-Print Network (OSTI)

two trails of using solid recovered fuel and received theand briquettes. Densified recovered solid fuel can have net

Hasanbeigi, Ali

2013-01-01T23:59:59.000Z

177

International Best Practices for Pre-Processing and Co-Processing Municipal Solid Waste and Sewage Sludge in the Cement Industry  

E-Print Network (OSTI)

least two seconds. ” The waste heat from the co-processingis drawn from the waste heat of the associated cementSewage sludge drying using waste heat from cement plant flue

Hasanbeigi, Ali

2013-01-01T23:59:59.000Z

178

Industrial Solid Waste Landfill Facilities (Ohio) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Industrial Solid Waste Landfill Facilities (Ohio) Industrial Solid Waste Landfill Facilities (Ohio) Industrial Solid Waste Landfill Facilities (Ohio) < Back Eligibility Agricultural Industrial Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative State/Provincial Govt Utility Program Info State Ohio Program Type Environmental Regulations Provider Ohio Environmental Protection Agency This chapter of the law establishes that the Ohio Environmental Protection Agency provides rules and guidelines for landfills, including those that treat waste to generate electricity. The law provides information for permitting, installing, maintaining, monitoring, and closing landfills. There are no special provisions or exemptions for landfills used to generate electricity. However, the law does apply to landfills that do

179

Municipal Solid-State Street Lighting Consortium Kickoff Webcast  

Energy.gov (U.S. Department of Energy (DOE))

This May 6, 2010 webcast served as the first official meeting of the new DOE Municipal Solid-State Street Lighting Consortium. Ed Smalley of Seattle City Light and Bruce Kinzey of Pacific Northwest...

180

Frequently Asked Questions About the Municipal Solid-State Street Lighting Consortium  

Energy.gov (U.S. Department of Energy (DOE))

This page addresses many of the questions about the Municipal Solid-State Street Lighting Consortium.

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Quality Services: Solid Wastes, Part 361: Siting of Industrial Hazardous  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1: Siting of Industrial 1: Siting of Industrial Hazardous Waste Facilities (New York) Quality Services: Solid Wastes, Part 361: Siting of Industrial Hazardous Waste Facilities (New York) < Back Eligibility Commercial Fed. Government Industrial Investor-Owned Utility Local Government Municipal/Public Utility State/Provincial Govt Tribal Government Utility Program Info State New York Program Type Siting and Permitting Provider NY Department of Environmental Conservation These regulations describe the siting of new industrial hazardous waste facilities located wholly or partially within the State. Industrial hazardous waste facilities are defined as facilities used for the purpose of treating, storing, compacting, recycling, exchanging or disposing of industrial hazardous waste materials, including treatment, compacting,

182

Nonhazardous Solid Waste Management Regulations and Criteria (Mississippi)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Nonhazardous Solid Waste Management Regulations and Criteria Nonhazardous Solid Waste Management Regulations and Criteria (Mississippi) Nonhazardous Solid Waste Management Regulations and Criteria (Mississippi) < Back Eligibility Agricultural Commercial Construction Developer Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Mississippi Program Type Environmental Regulations

183

Solid Waste Management Act (West Virginia) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Act (West Virginia) Act (West Virginia) Solid Waste Management Act (West Virginia) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Program Info State West Virginia Program Type Siting and Permitting Provider Department of Environmental Protection In addition to establishing a comprehensive program of controlling all phases of solid waste management and assigning responsibilities for solid waste management to the Secretary of Department of Environmental

184

Hazardous and Nonhazardous Solid Waste Applicant Disclosure Regulations  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hazardous and Nonhazardous Solid Waste Applicant Disclosure Hazardous and Nonhazardous Solid Waste Applicant Disclosure Regulations (Mississippi) Hazardous and Nonhazardous Solid Waste Applicant Disclosure Regulations (Mississippi) < Back Eligibility Agricultural Commercial Construction Developer Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Mississippi Program Type

185

International Best Practices for Pre-Processing and Co-Processing Municipal Solid Waste and Sewage Sludge in the Cement Industry  

E-Print Network (OSTI)

composition is 6-percent coal/petcoke/animal meal mix, 16-sawdust Coal, plastic, and tires Tires Petcoke, plastic, andwaste oil Petcoke, sunflower shells, and waste oil Tire

Hasanbeigi, Ali

2013-01-01T23:59:59.000Z

186

Impact of Municipal Solid Waste (MSW) Quality on the Behavior of Alkali Metals and Trace Elements during Combustion: A Thermodynamic Equilibrium Analysis  

Science Journals Connector (OSTI)

Light, thermal- and bacterial-resistant, and inexpensive leathers, especially in the footwear industry, are obtained by the Cr tanning method. ... The selected waste items are representing the major combustible fractions found in MSW, i.e. paper, plastic, textile, and biogenic materials (both food and biomass), but also the other waste fraction (a mixed and poorly defined fraction). ... Pedersen et al.(6) studies six different waste fractions separately under different operational conditions in a full-scale incinerator: NaCl (road salt), household batteries, automotive shredder waste (rubber and plastics), Cu?Cr?As (CCA)-impregnated wood, PVC, and shoes (leather mainly). ...

Michae?l Becidan; Lars Sřrum; Daniel Lindberg

2010-05-21T23:59:59.000Z

187

Biohazardous Waste Disposal Guidelines Sharps Waste Solid Lab Waste Liquid Waste Animals Pathological Waste  

E-Print Network (OSTI)

waste (i.e, mixture of biohazardous and chemical or radioactive waste), call Environment, Health2/2009 Biohazardous Waste Disposal Guidelines Sharps Waste Solid Lab Waste Liquid Waste Animals Pathological Waste Description Biohazard symbol Address: UCSD 200 West Arbor Dr. San Diego, CA 92103 (619

Tsien, Roger Y.

188

Integrated Solid Waste Management Act (Nebraska) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here You are here Home » Integrated Solid Waste Management Act (Nebraska) Integrated Solid Waste Management Act (Nebraska) < Back Eligibility Agricultural Commercial Construction Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Program Info State Nebraska Program Type Siting and Permitting Provider Environmental Quality This act affirms the state's support for alternative waste management practices, including waste reduction and resource recovery. Each county and

189

Fluid-bed combustion of solid wastes  

SciTech Connect

For over ten years combustion Power Company has been conducting experimental programs and developing fluid bed systems for agencies of the federal government and for private industry and institutions. Many of these activities have involved systems for the combustion of solid waste materials. Discussed here will be three categories of programs, development of Municipal Solid Waste (MSW) fired fluid beds, development of wood waste fired fluid beds, and industrial installations. Research and development work on wood wastes has led to the design and construction of two large industrial fluid bed combustors. In one of these, a fluid bed is used for the generation of steam with a fuel that was previously suited only for landfill. Rocks and inerts are continuously removed from this combustor using a patented system. The second FBC is designed to use a variety of fuels as the source of energy to dry hog fuel for use in a high performance power boiler. Here the FBC burns green hog fuel, log yard debris, fly ash (char) from the boiler, and dried wood fines to produce a hot gas system for the wood dryer. A significant advantage of the fluidized bed reactor over conventional incinerators is its ability to reduce noxious gas emission and, finally, the fluidized bed is unique in its ability to efficiently consume low quality fuels. The relatively high inerts and moisture content of solid wastes pose no serious problem and require no associated additional devices for their removal.

Vander Molen, R.H.

1980-01-01T23:59:59.000Z

190

Georgia Comprehensive Solid Waste Management Act of 1990 (Georgia) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Georgia Comprehensive Solid Waste Management Act of 1990 (Georgia) Georgia Comprehensive Solid Waste Management Act of 1990 (Georgia) Georgia Comprehensive Solid Waste Management Act of 1990 (Georgia) < Back Eligibility Agricultural Commercial Construction Developer Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Program Info State Georgia Program Type Environmental Regulations Siting and Permitting Provider Georgia Department of Natural Resources The Georgia Comprehensive Solid Waste Management Act (SWMA) of 1990 was implemented in order to improve solid waste management procedures,

191

Solid Waste Assessment Fee Exemptions (West Virginia) | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Solid Waste Assessment Fee Exemptions (West Virginia) Solid Waste Assessment Fee Exemptions (West Virginia) Solid Waste Assessment Fee Exemptions (West Virginia) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Program Info State West Virginia Program Type Rebate Program A person who owns, operates, or leases an approved solid waste disposal facility is exempt from the payment of solid waste assessment fees, upon the receipt of a Certificate of Exemption from the director, if that

192

Information Resources: Webcast: Municipal Solid-State Street Lighting  

NLE Websites -- All DOE Office Websites (Extended Search)

Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool This April 3, 2012 webcast presented information about the Retrofit Financial Analysis Tool developed by DOE"s Municipal Solid-State Street Lighting Consortium. Doug Elliott of Pacific Northwest National Laboratory provided a guided walk-through of what the tool can do and how to use it to evaluate costs and benefits associated with converting to LED street and roadway lighting. The webcast showed how city and other government agencies, utilities, finance and budget offices, and energy efficiency organizations can use the tool to compute annualized energy-cost savings, maintenance savings, greenhouse gas reductions, net present value, and simple payback, which can be helpful when putting together construction and conservation grant applications, as well as for preparing budgets and comparing incumbent costs to new costs.

193

Application of Geographical Information System (GIS) in optimisation of waste collection for Alandur Municipality in South Chennai, India  

Science Journals Connector (OSTI)

The population outburst in urban areas had resulted in a substantial increase in the generation of Municipal Solid Waste (MSW) and challenged with waste management. Issam et al. (2007) pointed out that most of the cities which is burning the waste in open dumps lacks in proper health and safety requirements. Alandur which is under Alandur Municipal Corporation (AMC) generate nearly 80 MT MSW every day. Due to improper institutional mechanism for collection and conveyance of waste, an engineered design for storage, collection and conveyance using GIS incorporating route optimisation had been discussed in this paper.

T.E. Kanchanabhan; Srinivasan Selvaraj; V. Lenin Kalyana Sundaram; J. Abbas Mohaideen

2011-01-01T23:59:59.000Z

194

Integrated solid waste management of Springfield, Massachusetts  

SciTech Connect

The subject document reports the results of an in-depth investigation of the fiscal year 1993 cost of the city of Springfield, Massachusetts, integrated municipal solid waste management (IMSWM) system, the energy consumed to operate the system, and the environmental performance requirements for each of the system`s waste-processing and disposal facilities. The document reports actual data from records kept by participants. Every effort was made to minimize the use of assumptions, and no attempt is made to interpret the data reported. Analytical approaches are documented so that interested analysts may perform manipulation or further analysis of the data. As such, the report is a reference document for Municipal Solid Waste management professionals who are interested in the actual costs and energy consumption, for a 1-year period, of an operating IMSWM system. The report is organized into two main parts. The first part is the executive summary and case study portion of the report. The executive summary provides a basic description of the study area and selected economic and energy information. Within the case study are detailed descriptions of each component operating during the study period; the quantities of solid waste collected, processed, and marketed within the study boundaries; the cost of managing MSW in Springfield; an energy usage analysis; a review of federal, state, and local environmental requirement compliance; a reference section; and a glossary of terms. The second part of the report focuses on a more detailed discourse on the above topics. In addition, the methodology used to determine the economic costs and energy consumption of the system components is found in the second portion of this report. The methodology created for this project will be helpful for those professionals who wish to break out the costs of their own integrated systems.

NONE

1995-11-01T23:59:59.000Z

195

Solid Waste Planning and Recycling Act (Illinois)  

Energy.gov (U.S. Department of Energy (DOE))

It is the purpose of this Act to provide incentives for decreased generation of municipal waste, to require certain counties to develop comprehensive waste management plans that place substantial...

196

Solid Waste Management Rules (Vermont)  

Energy.gov (U.S. Department of Energy (DOE))

These rules establish procedures and standards to protect public health and the environment by ensuring the safe, proper, and sustainable management of solid waste in Vermont. The rules apply to...

197

Nuclear waste solids  

Science Journals Connector (OSTI)

Glass and polycrystalline materials for high-level radioactive waste immobilization are discussed. Borosilicate glass has been selected as the waste form for defence high-level radwaste in the US. Since releas...

L. L. Hench; D. E. Clark; A. B. Harker

1986-05-01T23:59:59.000Z

198

Solid Waste Management (South Dakota) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

South Dakota) South Dakota) Solid Waste Management (South Dakota) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Program Info State South Dakota Program Type Siting and Permitting Provider South Dakota Department of Environment and Natural Resources This statute contains provisions for solid waste management systems, groundwater monitoring, liability for pollution, permitting, inspections, and provisions for waste reduction and recycling programs

199

Integrated solid waste management of Seattle, Washington  

SciTech Connect

The subject document reports the results of an in-depth investigation of the fiscal year 1992 cost of the City of Seattle, Washington, integrated municipal solid waste management (IMSWM) system, the energy consumed to operate the system, and the environmental performance requirements for each of the system`s waste-processing and disposal facilities. Actual data from records kept by participants is reported in this document. Every effort was made to minimize the use of assumptions, and no attempt is made to interpret the data reported. Analytical approaches are documented so that interested analysts may perform manipulation or further analysis of the data. As such, the report is a reference document for MSW management professionals who are interested in the actual costs and energy consumption for a one-year period, of an operating IMSWM systems.

NONE

1995-11-01T23:59:59.000Z

200

Electric power generation using a phosphoric acid cell on a municipal solid waste landfill gas stream. Technology verification report, November 1997--July 1998  

SciTech Connect

The report gives results of tests to verify the performance of a landfill gas pretreatment unit (GPU) and a phosphoric acid fuel cell system. The complete system removes contaminants from landfill gas and produces electricity for on-site use or connection to an electric grid. Performance data were collected at two sites determined to be representative of the U.S. landfill market. The Penrose facility, in Los Angeles, CA, was the first test site. The landfill gas at this site represented waste gas recovery from four nearby landfills, consisting primarily of industrial waste material. It produced approximately 3000 scf of gas/minute, and had a higher heating value of 446 Btu/scf at about 44% methane concentration. The second test site, in Groton, CT, was a relatively small landfill, but with greater heat content gas (methane levels were about 57% and the average heating value was 585 Btu/scf). The verification test addressed contaminant removal efficiency, flare destruction efficiency, and the operational capability of the cleanup system, and the power production capability of the fuel cell system.

Masemore, S.; Piccot, S.

1998-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Solid Waste Management Policy and Programs (Minnesota) | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Policy and Programs (Minnesota) Policy and Programs (Minnesota) Solid Waste Management Policy and Programs (Minnesota) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Program Info State Minnesota Program Type Siting and Permitting These statutes encourage the State and local governments to develop waste management strategies to achieve the maximum possible reduction in waste generation, eliminate or reduce adverse environmental impacts, encourage

202

Clean energy from municipal solid waste  

SciTech Connect

This progress report describes a slurry grinding trial where a carbonized refuse derived fuel was dispersed in water. The RDF slurry produced in this study is to subjected to dioxin combustion tests.

Klosky, M.

1996-07-02T23:59:59.000Z

203

SYNERGIA Forum Integrated Municipal Solid Waste Management  

E-Print Network (OSTI)

ERT Germany "Biogas utilization: Comparison between sanitary landfills and anaerobic digestionERT Germany, WTE Plants in Germany" Michael Jakuttis, Dipl.Ing. Wt

Columbia University

204

Tapping Resources in Municipal Solid Waste  

Science Journals Connector (OSTI)

...operation: ferrous losses in the light fraction resulting from air classifica-tion...by air classifica-tion into light and heavy fractions, and the 20 FEBRUARY 1976 MINOR...screening after fracture in a shredder. It lends itself well to gravity...

S. L. Blum

1976-02-20T23:59:59.000Z

205

Waste utilization as an energy source: Municipal wastes. (Latest citations from the NTIS bibliographic database). Published Search  

SciTech Connect

The bibliography contains citations concerning the utilization of municipal wastes as an energy source. Articles discuss energy derived from incineration/combustion, refuse-derived fuels, co-firing municipal waste and standard fuels, landfill gas production, sewage combustion, and other waste-to-energy technologies. Citations address economics and efficiencies of various schemes to utilize municipal waste products as energy sources. (Contains a minimum of 130 citations and includes a subject term index and title list.)

Not Available

1994-05-01T23:59:59.000Z

206

Energy and solid/hazardous waste  

SciTech Connect

This report addresses the past and potential future solid and hazardous waste impacts from energy development, and summarizes the major environmental, legislation applicable to solid and hazardous waste generation and disposal. A glossary of terms and acronyms used to describe and measure solid waste impacts of energy development is included. (PSB)

None

1981-12-01T23:59:59.000Z

207

1993 Solid Waste Reference Forecast Summary  

SciTech Connect

This report, which updates WHC-EP-0567, 1992 Solid Waste Reference Forecast Summary, (WHC 1992) forecasts the volumes of solid wastes to be generated or received at the US Department of Energy Hanford Site during the 30-year period from FY 1993 through FY 2022. The data used in this document were collected from Westinghouse Hanford Company forecasts as well as from surveys of waste generators at other US Department of Energy sites who are now shipping or plan to ship solid wastes to the Hanford Site for disposal. These wastes include low-level and low-level mixed waste, transuranic and transuranic mixed waste, and nonradioactive hazardous waste.

Valero, O.J.; Blackburn, C.L. [Westinghouse Hanford Co., Richland, WA (United States); Kaae, P.S.; Armacost, L.L.; Garrett, S.M.K. [Pacific Northwest Lab., Richland, WA (United States)

1993-08-01T23:59:59.000Z

208

Household solid waste characteristics and management in Chittagong, Bangladesh  

SciTech Connect

Solid waste management (SWM) is a multidimensional challenge faced by urban authorities, especially in developing countries like Bangladesh. We investigated per capita waste generation by residents, its composition, and the households' attitudes towards waste management at Rahman Nagar Residential Area, Chittagong, Bangladesh. The study involved a structured questionnaire and encompassed 75 households from five different socioeconomic groups (SEGs): low (LSEG), lower middle (LMSEG), middle (MSEG), upper middle (UMSEG) and high (HSEG). Wastes, collected from all of the groups of households, were segregated and weighed. Waste generation was 1.3 kg/household/day and 0.25 kg/person/day. Household solid waste (HSW) was comprised of nine categories of wastes with vegetable/food waste being the largest component (62%). Vegetable/food waste generation increased from the HSEG (47%) to the LSEG (88%). By weight, 66% of the waste was compostable in nature. The generation of HSW was positively correlated with family size (r{sub xy} = 0.236, p < 0.05), education level (r{sub xy} = 0.244, p < 0.05) and monthly income (r{sub xy} = 0.671, p < 0.01) of the households. Municipal authorities are usually the responsible agencies for solid waste collection and disposal, but the magnitude of the problem is well beyond the ability of any municipal government to tackle. Hence dwellers were found to take the service from the local waste management initiative. Of the respondents, an impressive 44% were willing to pay US$0.3 to US$0.4 per month to waste collectors and it is recommended that service charge be based on the volume of waste generated by households. Almost a quarter (22.7%) of the respondents preferred 12-1 pm as the time period for their waste to be collected. This study adequately shows that household solid waste can be converted from burden to resource through segregation at the source, since people are aware of their role in this direction provided a mechanism to assist them in this pursuit exists and the burden is distributed according to the amount of waste generated.

Sujauddin, Mohammad [Institute of Forestry and Environmental Sciences, Chittagong University, Chittagong-4331 (Bangladesh)], E-mail: mohammad.sujauddin@gmail.com; Huda, S.M.S. [Institute of Forestry and Environmental Sciences, Chittagong University, Chittagong-4331 (Bangladesh); Hoque, A.T.M. Rafiqul [Institute of Forestry and Environmental Sciences, Chittagong University, Chittagong-4331 (Bangladesh); Laboratory of Ecology and Systematics (Plant Ecophysiology Section), Faculty of Science, Biology Division, University of the Ryukyus, Okinawa 903-0213 (Japan)

2008-07-01T23:59:59.000Z

209

Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Kickoff  

Energy.gov (U.S. Department of Energy (DOE))

Below is the text-alternative version of the Municipal Solid-State Street Lighting Consortium Kickoff webcast, held May 6, 2010.

210

Text-Alternative Version: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool Webcast  

Energy.gov (U.S. Department of Energy (DOE))

Below is the text-alternative version of the "Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool" webcast, held April 3, 2012.

211

WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Doubles Solid Waste Reduction Rate in Fiscal Year 2013 Doubles Solid Waste Reduction Rate in Fiscal Year 2013 WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 December 5, 2013 - 12:00pm Addthis WIPP environmental and operations personnel gather next to pallets that will be provided to the local community as part of WIPP’s wood waste diversion program. WIPP environmental and operations personnel gather next to pallets that will be provided to the local community as part of WIPP's wood waste diversion program. CARLSBAD, N.M. - EM's Waste Isolation Pilot Plant (WIPP) almost doubled its solid waste reduction rate from 15.5 percent in fiscal year 2012 to 33 percent in fiscal year 2013 through programs that diverted WIPP's wood waste from the municipal landfill by reusing, repurposing or recycling.

212

WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 December 5, 2013 - 12:00pm Addthis WIPP environmental and operations personnel gather next to pallets that will be provided to the local community as part of WIPP’s wood waste diversion program. WIPP environmental and operations personnel gather next to pallets that will be provided to the local community as part of WIPP's wood waste diversion program. CARLSBAD, N.M. - EM's Waste Isolation Pilot Plant (WIPP) almost doubled its solid waste reduction rate from 15.5 percent in fiscal year 2012 to 33 percent in fiscal year 2013 through programs that diverted WIPP's wood waste from the municipal landfill by reusing, repurposing or recycling.

213

Quality Services: Solid Wastes, Parts 370-376: Hazardous Waste Management  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Parts 370-376: Hazardous Waste Parts 370-376: Hazardous Waste Management System (New York) Quality Services: Solid Wastes, Parts 370-376: Hazardous Waste Management System (New York) < Back Eligibility Commercial Fed. Government Industrial Investor-Owned Utility Local Government Municipal/Public Utility Rural Electric Cooperative Schools State/Provincial Govt Tribal Government Utility Program Info State New York Program Type Safety and Operational Guidelines Provider NY Department of Environmental Conservation These regulations prescribe the management of hazardous waste facilities in New York State. They identify and list different types of hazardous wastes and describe standards for generators, transporters, as well as treatment, storage and disposal facilities. The regulations also define specific types

214

Solid Waste Management and Land Protection (North Dakota) | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Land Protection (North Dakota) and Land Protection (North Dakota) Solid Waste Management and Land Protection (North Dakota) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Program Info State North Dakota Program Type Siting and Permitting The policy of the State of North Dakota is to encourage and provide for environmentally acceptable and economical solid waste management practices, and the Department of Health may promulgate regulations related to waste

215

The multiple market-exposure of waste management companies: A case study of two Swedish municipally owned companies  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Swedish municipally owned waste management companies are active on political, material, technical, and commercial markets. Black-Right-Pointing-Pointer These markets differ in kind and their demands follow different logics. Black-Right-Pointing-Pointer These markets affect the public service, processing, and marketing of Swedish waste management. Black-Right-Pointing-Pointer Articulating these markets is a strategic challenge for Swedish municipally owned waste management. - Abstract: This paper describes how the business model of two leading Swedish municipally owned solid waste management companies exposes them to four different but related markets: a political market in which their legitimacy as an organization is determined; a waste-as-material market that determines their access to waste as a process input; a technical market in which these companies choose what waste processing technique to use; and a commercial market in which they market their products. Each of these markets has a logic of its own. Managing these logics and articulating the interrelationships between these markets is a key strategic challenge for these companies.

Corvellec, Herve, E-mail: herve.corvellec@ism.lu.se [Department of Service Management, Lund University, Campus Helsingborg, PO Box 882, SE-251 08 Helsingborg (Sweden); Bramryd, Torleif [Department of Environmental Strategy, Lund University, Campus Helsingborg, PO Box 882, SE-251 08 Helsingborg (Sweden)

2012-09-15T23:59:59.000Z

216

Solid Waste Program Website | Open Energy Information  

Open Energy Info (EERE)

Program Website Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Solid Waste Program Website Author Alaska Division of Environmental Health Published...

217

Idaho Solid Waste Webpage | Open Energy Information  

Open Energy Info (EERE)

Webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Idaho Solid Waste Webpage Abstract This webpage provides an overview of regulation of solid...

218

DOE Municipal Solid-State Street Lighting Consortium  

Energy.gov (U.S. Department of Energy (DOE))

The DOE Municipal Solid-State Street Lighting Consortium shares technical information and experiences related to LED street and area lighting demonstrations and serves as an objective resource for evaluating new products on the market intended for those applications. Cities, power providers, and others who invest in street and area lighting are invited to join the Consortium and share their experiences. The goal is to build a repository of valuable field experience and data that will significantly accelerate the learning curve for buying and implementing high-quality, energy-efficient LED lighting. Consortium members are part of an international knowledge base and peer group, receive updates on Consortium tools and resources, receive the Consortium E-Newsletter, and help steer the work of the Consortium by participating on a committee. Learn more about the Consortium.

219

A New ACS Audio Course to help you understand and solve industrial and municipal waste-water problems ....  

Science Journals Connector (OSTI)

A New ACS Audio Course to help you understand and solve industrial and municipal waste-water problems .... ...

1982-08-01T23:59:59.000Z

220

Solid waste management: a public policy study  

E-Print Network (OSTI)

not be discharged into surface water in violation of the National Pollutant Discharge Elimination System of the Clean Water Act; and no facility may contaminate an underground drinking waste source beyond the plant boundary. 2. Air: No open burning... of residential, commercial, institutional, or industrial solid waste may take place. Certain periodic burning activities are exempt. 3. Farmland: No solid waste facility border may lie within one meter (three feet) of land used for crop. If polychlorinated...

Jayawant, Mandar Prabhatkumar

2012-06-07T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Control of air pollution emissions from municipal waste combustors  

SciTech Connect

The November 1990 Clear Air Act Amendments (CAAAs) directed EPA to establish municipal waste combustor (MWC) emissions limits for particulate matter, opacity, hydrogen chloride, sulfur dioxide, nitrogen oxides, carbon monoxide, dioxins, dibenzofurans, cadmium, lead, and mercury. Revised MWC air pollution regulations were subsequently proposed by EPA on September 20, 1994, and promulgated on December 19, 1995. The MWC emission limits were based on the application of maximum achievable control technology (MACT). This paper provides a brief overview of MWC technologies, a summary of EPA`s revised air pollution rules for MWCs, a review of current knowledge concerning formation and control of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans, and a discussion of the behavior and control of mercury in MWC flue gases. 56 refs., 11 figs., 3 tabs.

Kolgroe, J.D. [Environmental Protection Agency, Research Triangle Park, NC (United States). National Risk Management Research Lab.; Licata, A. [Licata Energy and Environmental Consultants, Inc., Yonkers, NY (United States)

1996-09-01T23:59:59.000Z

222

Hawaii Permit Application for Solid Waste Management Facility...  

Open Energy Info (EERE)

to receive a permit for a solid waste management facility. Form Type CertificateForm of Completion Form Topic Permit Application for Solid Waste Management Facility Organization...

223

Biosolids are the solids produced during municipal wastewater treatment. Composts are made from a variety of organic materials, including both urban and agriculture  

E-Print Network (OSTI)

ISSUE Biosolids are the solids produced during municipal wastewater treatment. Composts are made resources, restoring soils, and combating climate change. Biosolids are still viewed as harmful wastes County and a number of smaller treatment plants is applied to dryland wheat in Douglas County. More than

Collins, Gary S.

224

Solid Waste Management Rule (West Virginia) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Rule (West Virginia) Rule (West Virginia) Solid Waste Management Rule (West Virginia) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Construction Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Retail Supplier Institutional Multi-Family Residential Systems Integrator Fuel Distributor Nonprofit General Public/Consumer Transportation Program Info State West Virginia Program Type Siting and Permitting This rule establishes requirements for the siting, financial assurance, installation, establishment, construction, design, groundwater monitoring, modification, operation, permitting, closure and post-closure care of any

225

Solid Waste Program (Alabama) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Program (Alabama) Program (Alabama) Solid Waste Program (Alabama) < Back Eligibility Commercial Construction Developer General Public/Consumer Industrial Residential Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Alabama Program Type Environmental Regulations This article states the authority of the department, regulations for the control of unauthorized dumping, disposal fees, violations and penalties. Solid waste refers to any garbage, rubbish, construction or demolition debris, ash, or sludge from a waste treatment facility, water supply plant, or air pollution control facility, and any other discarded materials, including solid, liquid, semisolid, or contained gaseous material resulting

226

Hanford Site Solid Waste Acceptance Criteria  

SciTech Connect

This manual defines the Hanford Site radioactive, hazardous, and sanitary solid waste acceptance criteria. Criteria in the manual represent a guide for meeting state and federal regulations; DOE Orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to acceptance of radioactive and hazardous solid waste at the Hanford Site. It is not the intent of this manual to be all inclusive of the regulations; rather, it is intended that the manual provide the waste generator with only the requirements that waste must meet in order to be accepted at Hanford Site TSD facilities.

Not Available

1993-11-17T23:59:59.000Z

227

Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool  

Energy.gov (U.S. Department of Energy (DOE))

This April 3, 2012 webcast presented information about the Retrofit Financial Analysis Tool developed by DOE"s Municipal Solid-State Street Lighting Consortium. Doug Elliott of Pacific Northwest...

228

Geothermal Direct-Use — Minimizing Solid Waste  

Energy.gov (U.S. Department of Energy (DOE))

Aquaculture and horticulture businesses, and other industries that use geothermal direct-use systems typically don't generate any more solid waste than those that use other energy resources.

229

County Solid Waste Control Act (Texas)  

Energy.gov (U.S. Department of Energy (DOE))

The purpose of this chapter is to authorize a cooperative effort by counties, public agencies, and other persons for the safe and economical collection, transportation, and disposal of solid waste...

230

Phase 2, Solid waste retrieval strategy  

SciTech Connect

Solid TRU retrieval, Phase 1 is scheduled to commence operation in 1998 at 218W-4C-T01 and complete recovery of the waste containers in 2001. Phase 2 Retrieval will recover the remaining buried TRU waste to be retrieved and provide the preliminary characterization by non-destructive means to allow interim storage until processing for disposal. This document reports on researching the characterization documents to determine the types of wastes to be retrieved and where located, waste configurations, conditions, and required methods for retrieval. Also included are discussions of wastes encompassed by Phase 2 for which there are valid reasons to not retrieve.

Johnson, D.M.

1994-09-29T23:59:59.000Z

231

Energy implications of the thermal recovery of biodegradable municipal waste materials in the United Kingdom  

SciTech Connect

Highlights: > Energy balances were calculated for the thermal treatment of biodegradable wastes. > For wood and RDF, combustion in dedicated facilities was the best option. > For paper, garden and food wastes and mixed waste incineration was the best option. > For low moisture paper, gasification provided the optimum solution. - Abstract: Waste management policies and legislation in many developed countries call for a reduction in the quantity of biodegradable waste landfilled. Anaerobic digestion, combustion and gasification are options for managing biodegradable waste while generating renewable energy. However, very little research has been carried to establish the overall energy balance of the collection, preparation and energy recovery processes for different types of wastes. Without this information, it is impossible to determine the optimum method for managing a particular waste to recover renewable energy. In this study, energy balances were carried out for the thermal processing of food waste, garden waste, wood, waste paper and the non-recyclable fraction of municipal waste. For all of these wastes, combustion in dedicated facilities or incineration with the municipal waste stream was the most energy-advantageous option. However, we identified a lack of reliable information on the energy consumed in collecting individual wastes and preparing the wastes for thermal processing. There was also little reliable information on the performance and efficiency of anaerobic digestion and gasification facilities for waste.

Burnley, Stephen, E-mail: s.j.burnley@open.ac.uk [Open University, Walton Hall, Milton Keynes MK7 6AA (United Kingdom); Phillips, Rhiannon, E-mail: rhiannon.jones@environment-agency.gov.uk [Strategy Unit, Welsh Assembly Government, Ty Cambria, 29 Newport Road, Cardiff CF24 0TP (United Kingdom); Coleman, Terry, E-mail: terry.coleman@erm.com [Environmental Resources Management Ltd, Eaton House, Wallbrook Court, North Hinksey Lane, Oxford OX2 0QS (United Kingdom); Rampling, Terence, E-mail: twa.rampling@hotmail.com [7 Thurlow Close, Old Town Stevenage, Herts SG1 4SD (United Kingdom)

2011-09-15T23:59:59.000Z

232

Energy aspects of solid waste management: Proceedings  

SciTech Connect

The Eighteenth Annual Illinois Energy Conference entitled ``Energy Aspects of Solid Waste Management`` was held in Chicago, Illinois on October 29--30, 1990. The conference program was developed by a planning committee that drew upon Illinois energy and environmental specialists from the major sectors including energy industries, environmental organizations, research universities, utility companies, federal, state and local government agencies, and public interest groups. Within this framework, the committee identified a number of key topic areas surrounding solid waste management in Illinois which were the focus of the conference. These issues included: review of the main components of the solid waste cycle in the Midwest and what the relative impact of waste reduction, recycling, incineration and land disposal might be on Illinois` and the Midwest`s solid waste management program. Investigation of special programs in the Midwest dealing with sewage sludge, combustion residuals and medical/infectious wastes. Review of the status of existing landfills in Illinois and the Midwest and an examination of the current plans for siting of new land disposal systems. Review of the status of incinerators and waste-to-energy systems in Illinois and the Midwest, as well as an update on activities to maximize methane production from landfills in the Midwest.

Not Available

1990-12-31T23:59:59.000Z

233

If current capacity were to be expanded so that all of the non-recycled municipal solid waste that is currently sent to U.S. landfills each year could instead be converted to energy, we could generate enough electricity  

E-Print Network (OSTI)

so that we could convert our non-recycled waste to alternative energy instead of landfilling it, we-recycled waste into energy instead of landfilling it, we could reduce greenhouse gas (GHG) emissions by nearly our roads. The Power of Waste GARBAGE ENERGY REDUCES 123M TONS CO2 = 23M LESS CARS PLASTICS 5.7B

234

One?dimensional Seismic Analysis of a Solid?Waste Landfill  

Science Journals Connector (OSTI)

Analysis of the seismic performance of solid waste landfill follows generally the same procedures for the design of embankment dams even if the methods and safety requirements should be different. The characterization of waste properties for seismic design is difficult due the heterogeneity of the material requiring the procurement of large samples. The dynamic characteristics of solid waste materials play an important role on the seismic response of landfill and it also is important to assess the dynamic shear strengths of liner materials due the effect of inertial forces in the refuse mass. In the paper the numerical results of a dynamic analysis are reported and analysed to determine the reliability of the common practice of using 1D analysis to evaluate the seismic response of a municipal solid?waste landfill. Numerical results indicate that the seismic response of a landfill can vary significantly due to reasonable variations of waste properties fill heights site conditions and design rock motions.

Francesco Castelli; Valentina Lentini; Michele Maugeri

2008-01-01T23:59:59.000Z

235

An approach for sampling solid heterogeneous waste at the Hanford Site waste receiving and processing and solid waste projects  

SciTech Connect

This paper addresses the problem of obtaining meaningful data from samples of solid heterogeneous waste while maintaining sample rates as low as practical. The Waste Receiving and Processing Facility, Module 1, at the Hanford Site in south-central Washington State will process mostly heterogeneous solid wastes. The presence of hazardous materials is documented for some packages and unknown for others. Waste characterization is needed to segregate the waste, meet waste acceptance and shipping requirements, and meet facility permitting requirements. Sampling and analysis are expensive, and no amount of sampling will produce absolute certainty of waste contents. A sampling strategy is proposed that provides acceptable confidence with achievable sampling rates.

Sexton, R.A.

1993-03-01T23:59:59.000Z

236

1993 baseline solid waste management system description  

SciTech Connect

Pacific Northwest Laboratory has prepared this report under the direction of Westinghouse Hanford Company. The report provides an integrated description of the system planned for managing Hanford`s solid low-level waste, low-level mixed waste, transuranic waste, and transuranic mixed waste. The primary purpose of this document is to illustrate a collective view of the key functions planned at the Hanford Site to handle existing waste inventories, as well as solid wastes that will be generated in the future. By viewing this system as a whole rather than as individual projects, key facility interactions and requirements are identified and a better understanding of the overall system may be gained. The system is described so as to form a basis for modeling the system at various levels of detail. Model results provide insight into issues such as facility capacity requirements, alternative system operating strategies, and impacts of system changes (ie., startup dates). This description of the planned Hanford solid waste processing system: defines a baseline system configuration; identifies the entering waste streams to be managed within the system; identifies basic system functions and waste flows; and highlights system constraints. This system description will evolve and be revised as issues are resolved, planning decisions are made, additional data are collected, and assumptions are tested and changed. Out of necessity, this document will also be revised and updated so that a documented system description, which reflects current system planning, is always available for use by engineers and managers. It does not provide any results generated from the many alternatives that will be modeled in the course of analyzing solid waste disposal options; such results will be provided in separate documents.

Armacost, L.L.; Fowler, R.A.; Konynenbelt, H.S.

1994-02-01T23:59:59.000Z

237

MidAmerican Energy (Electric) - Municipal Solid-State Lighting Grant  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MidAmerican Energy (Electric) - Municipal Solid-State Lighting MidAmerican Energy (Electric) - Municipal Solid-State Lighting Grant Program MidAmerican Energy (Electric) - Municipal Solid-State Lighting Grant Program < Back Eligibility Local Government Savings Category Appliances & Electronics Commercial Lighting Lighting Maximum Rebate Minimum project size for the full $5,000 grant is 20 fixtures; smaller projects will receive a $250 per-fixture grant. Program Info State Iowa Program Type Utility Grant Program Rebate Amount Up to $5,000 Provider MidAmerican Energy Company MidAmerican Energy offers grants to munipalities which implement solid-state roadway street lighting upgrades. Grants of up to $5,000 are available to participating entities who install eligible roadway lighting fixtures. Participants must be an Iowa electric governmental customer of

238

Constructed Wetlands and Waste Stabilization Ponds for municipal wastewater treatment in France: comparison of  

E-Print Network (OSTI)

13 Constructed Wetlands and Waste Stabilization Ponds for municipal wastewater treatment in France In France, vertical flow constructed wetlands and waste stabilisation ponds are both extensive treatment processes well adapted to small rural communities mainly because they are easy to operate

Paris-Sud XI, Université de

239

EIS-0286: Hanford Solid (Radioactive and Hazardous) Waste Program  

Energy.gov (U.S. Department of Energy (DOE))

The Hanford Site Solid (Radioactive and Hazardous) Waste Program Environmental Impact Statement (HSW EIS) analyzes the proposed waste management practices at the Hanford Site.

240

South Carolina Solid Waste Policy and Management Act (South Carolina)  

Energy.gov (U.S. Department of Energy (DOE))

The state of South Carolina supports a regional approach to solid waste management and encourages the development and implementation of alternative waste management practices and resource recovery....

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Processing and utilizing high heat value, low ash alternative fuels from urban solid waste  

SciTech Connect

The history of technologies in the US that recover energy from urban solid waste is relatively short. Most of the technology as we know it evolved over the past 25 years. This evolution led to the development of about 100 modern mass burn and RDF type waste-to-energy plants and numerous small modular combustion systems, which collectively are handling about 20%, or about 40 million tons per year, of the nations municipal solid waste. Technologies also evolved during this period to co-fire urban waste materials with other fuels or selectively burn specific waste streams as primary fuels. A growing number of second or third generation urban waste fuels projects are being developed. This presentation discusses new direction in the power generating industry aimed at recovery and utilization of clean, high heat value, low ash alternative fuels from municipal and industrial solid waste. It reviews a spectrum of alternative fuels for feasible recovery and reuse, with new opportunities emerging for urban fuels processors providing fuels in the 6,000--15,000 BTU/LB range for off premises use.

Smith, M.L. [M.L. Smith Environmental and Associates, Tinley Park, IL (United States)

1995-10-01T23:59:59.000Z

242

MidAmerican Energy (Electric) - Municipal Solid-State Lighting Grant  

Open Energy Info (EERE)

MidAmerican Energy (Electric) - Municipal Solid-State Lighting Grant MidAmerican Energy (Electric) - Municipal Solid-State Lighting Grant Program (Iowa) No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Summary Last modified on November 9, 2012. Financial Incentive Program Place Iowa Additional Place applies to MidAmerican Energy Name MidAmerican Energy (Electric) - Municipal Solid-State Lighting Grant Program Incentive Type Utility Grant Program Applicable Sector Local Government Eligible Technologies Lighting, Lighting Controls/Sensors, Induction Lighitng, LED Lighting Active Incentive Yes Implementing Sector Utility Energy Category Energy Efficiency Incentive Programs Amount Up to $5,000 Equipment Requirements Fixtures must have an efficiency rating equal to or greater than 66 lumens per watt as tested under Illuminating Engineering Society of North America LM-79-08 testing to qualify for a grant.

243

Solid waste recycling programs at Rocky Flats  

SciTech Connect

The Rocky Flats (RFP) recycling programs for solid waste materials have been in place for over ten years. Within the last three years, the programs were centralized under the direction of the Rocky Flats Waste Minimization department, with the assistance of various plant organizations (e.g., Trucking, Building Services, Regulated Waste Operations, property Utilization and Disposal and Security). Waste Minimization designs collection and transportation systems for recyclable materials and evaluates recycling markets for opportunities to add new commodities to the existing programs. The Waste Minimization department also promotes employee participation in the Rocky Flats Recycling Programs, and collects all recycling data for publication. A description of the program status as of January 1994 is given.

Millette, R.L.; Blackman, T.E.; Shepard, M.D. [EG and G Rocky Flats, Inc., Golden, CO (United States)

1994-12-31T23:59:59.000Z

244

Acceptability of Bettis Laboratories waste shipment to WHC solid waste  

SciTech Connect

The purpose of this document is to evaluate a potential discrepancy between the Solid Waste Management (SWM) Criticality Prevention Specifications and a proposed waste receipt from Bettis Laboratories. This analysis resolves an apparent discrepancy between two different requirements of the Central Waste Complex and 200 Area Low-Level Burial Grounds Criticality Prevention Specifications (CPS-SW-149-00002 and CPS-SW-149-00003 respectively). The analysis is being performed to enable Solid Waste Management to accept a specific package from Bettis Laboratories. This package meets the requirements of section 2.1.1 in that the total fissile content of the drum is less than 200g and the waste occupies greater than 20% of the container volume. The package may not appear, however, to meet the requirements of section 2.1.5 for maximum enrichment of uranium bearing waste, as will be described below. Based on this analysis for this specific package, the waste is shown to be critically safe under all conditions for which the 55-gallon drums (17C, 17H, or UN1A2) specification applies. This package can be accepted under the 55-gallon drum limitations on fissile quantity. No change to the CPS is required.

McDonald, K.M.

1995-04-20T23:59:59.000Z

245

Geothermal Power Plants — Minimizing Solid Waste and Recovering Minerals  

Energy.gov (U.S. Department of Energy (DOE))

Although many geothermal power plants generate no appreciable solid waste, the unique characteristics of some geothermal fluids require special attention to handle entrained solid byproducts.

246

Acute and Genetic Toxicity of Municipal Landfill Leachate  

E-Print Network (OSTI)

Municipal solid waste (MSW) landfills have been found to contain many of the same hazardous constituents as found in hazardous waste landfills. Because of the large number of MSW landfills, these sites pose a serious environmental threat...

Brown, K.W.; Schrab, G.E.; Donnelly, K.C.

247

Solid Waste Reduction, Recovery, and Recycling | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reduction, Recovery, and Recycling Reduction, Recovery, and Recycling Solid Waste Reduction, Recovery, and Recycling < Back Eligibility Investor-Owned Utility Rural Electric Cooperative Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Wisconsin Program Type Environmental Regulations Provider Department of Natural Resources This statute expresses the strong support of the State of Wisconsin for the reduction of the amount of solid waste generated, the reuse, recycling and composting of solid waste, and resource recovery from solid waste. The statute also notes that research, development and innovation in the design, management and operation of solid waste reduction, reuse, recycling,

248

System for chemically digesting low level radioactive, solid waste material  

DOE Patents (OSTI)

An improved method and system for chemically digesting low level radioactive, solid waste material having a high through-put. The solid waste material is added to an annular vessel (10) substantially filled with concentrated sulfuric acid. Concentrated nitric acid or nitrogen dioxide is added to the sulfuric acid within the annular vessel while the sulfuric acid is reacting with the solid waste. The solid waste is mixed within the sulfuric acid so that the solid waste is substantilly fully immersed during the reaction. The off gas from the reaction and the products slurry residue is removed from the vessel during the reaction.

Cowan, Richard G. (Kennewick, WA); Blasewitz, Albert G. (Richland, WA)

1982-01-01T23:59:59.000Z

249

Microsoft Word - Solid Waste at Hanford  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Use of American Recovery and Use of American Recovery and Reinvestment Act of 2009 Funds on Solid Waste Project Activities at the Department of Energy's Hanford Site OAS-RA-L-11-08 May 2011 DOE F 1325.8 (08-93) United States Government Department of Energy Memorandum DATE: May19, 2011 Audit Report Number: OAS-RA-L-11-08 REPLY TO ATTN OF: IG-34 (A10RA041) SUBJECT: Report on "Use of American Recovery and Reinvestment Act of 2009 Funds on Solid Waste Project Activities at the Department of Energy's Hanford Site" TO: Assistant Secretary for Environmental Management INTRODUCTION AND OBJECTIVE The Department of Energy's (Department), Richland Operations Office (Richland), awarded a contract, effective October 1, 2008, to CH2M HILL Plateau Remediation Company (CHPRC) to

250

Assessment of LANL solid low-level waste management documentation  

SciTech Connect

DOE Order 5820.2A requires that a system performance assessment be conducted to assure efficient and compliant management of all radioactive waste. The objective of this report is to determine the present status of the Radioactive Waste Operations Section's capabilities regarding preparation and maintenance of appropriate criteria, plans and procedures and identify particular areas where these documents are not presently in existence or being fully implemented. DOE Order 5820.2A, Radioactive Waste Management, Chapter III sets forth the requirements and guidelines for preparation and implementation of criteria, plans and procedures to be utilized in the management of solid low-level waste. The documents being assessed in this report are: Solid Low-Level Waste Acceptance Criteria, Solid Low-Level Waste Characterization Plan, Solid Low-Level Waste Certification Plan, Solid Low-Level Waste Acceptance Procedures, Solid Low-Level Waste Characterization Procedures, Solid Low-Level Waste Certification Procedures, Solid Low-Level Waste Training Procedures, and Solid Low-Level Waste Recordkeeping Procedures. Suggested outlines for these documents are presented as Appendix A.

Klein, R.B.; Jennrich, E.A.; Lund, D.M.; Danna, J.G. (Rogers and Associates Engineering Corp., Salt Lake City, UT (United States)); Davis, K.D.; Rutz, A.C. (Wastren, Inc., Idaho Falls, ID (United States))

1991-04-01T23:59:59.000Z

251

Assessment of LANL solid low-level waste management documentation  

SciTech Connect

DOE Order 5820.2A requires that a system performance assessment be conducted to assure efficient and compliant management of all radioactive waste. The objective of this report is to determine the present status of the Radioactive Waste Operations Section`s capabilities regarding preparation and maintenance of appropriate criteria, plans and procedures and identify particular areas where these documents are not presently in existence or being fully implemented. DOE Order 5820.2A, Radioactive Waste Management, Chapter III sets forth the requirements and guidelines for preparation and implementation of criteria, plans and procedures to be utilized in the management of solid low-level waste. The documents being assessed in this report are: Solid Low-Level Waste Acceptance Criteria, Solid Low-Level Waste Characterization Plan, Solid Low-Level Waste Certification Plan, Solid Low-Level Waste Acceptance Procedures, Solid Low-Level Waste Characterization Procedures, Solid Low-Level Waste Certification Procedures, Solid Low-Level Waste Training Procedures, and Solid Low-Level Waste Recordkeeping Procedures. Suggested outlines for these documents are presented as Appendix A.

Klein, R.B.; Jennrich, E.A.; Lund, D.M.; Danna, J.G. [Rogers and Associates Engineering Corp., Salt Lake City, UT (United States); Davis, K.D.; Rutz, A.C. [Wastren, Inc., Idaho Falls, ID (United States)

1991-04-01T23:59:59.000Z

252

E-Print Network 3.0 - aluminium dross waste Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Copyright 2008 by ASME Proceedings of NAWTEC16 16th Annual North American Waste... analysis of the mass streams and the properties of residual Municipal Solid Waste (MSW)....

253

Management approaches to integrated solid waste in industrialized zones in Jordan: A case of Zarqa City  

SciTech Connect

There is a need to recognize the difficulties experienced in managing waste and to understand the reasons for those difficulties, especially in developing countries such as Jordan. Zarqa is a Governorate located in central Jordan, which has 2874 registered industries, making up more than 52% of the total industries in the country. Zarqa Governorate suffers from serious solid waste problems. These problems arise from an absence of adequate policies, facilitating legislation, and an environmentally enthused public, which therefore have a negative impact on the environment and health. Solid waste generation in Zarqa Governorate has increased exponentially and has polluted natural resources and the environment. A significant change in municipal solid waste generation was evident between the years 1994 and 2000. The Zarqa Governorate generated 482 tons/day in 2002 with a per capita rate of 0.44 kg/cap-day [Consulting Engineers, 2002, Feasibility study for the treatment of industrial wastewater in Zarqa Governorate. A project funded by METAP and Zarqa Chamber of Industry. Unpublished report]. This manuscript assesses the current operational and management practices of solid waste in the Zarqa Governorate; and evaluates the associated issues of solid waste collection, storage, transport, disposal and recycling in developing countries. The lack of techniques, financial funds and awareness among public and private sectors form an obstacle for achieving a successful environmental program. Several options are proposed to address management goals. Although Jordan became the first country in the Middle East to adopt a national environmental strategy; waste disposal is still largely uncontrolled and large quantities of waste go uncollected. Ensuring proper management of solid wastes, enforcing regulations, and implementing proper environmental awareness programs that will enhance the public understanding and achieve greater efficiency, are the findings of this study.

Mrayyan, Bassam [Faculty of Natural Resources and Environment, Hashemite University, P.O. Box 150459, 13115 Zarqa (Jordan); Hamdi, Moshrik R. [Faculty of Natural Resources and Environment, Hashemite University, P.O. Box 150459, 13115 Zarqa (Jordan)]. E-mail: moshrik@hu.edu.jo

2006-07-01T23:59:59.000Z

254

Illinois Solid Waste Management Act (Illinois) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Illinois Solid Waste Management Act (Illinois) Illinois Solid Waste Management Act (Illinois) Illinois Solid Waste Management Act (Illinois) < Back Eligibility Agricultural Commercial Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Program Info State Illinois Program Type Environmental Regulations Provider Illinois EPA It is the purpose of this Act to reduce reliance on land disposal of solid waste, to encourage and promote alternative means of managing solid waste, and to assist local governments with solid waste planning and management. In furtherance of those aims, while recognizing that landfills will continue to be necessary, this Act establishes the following waste management hierarchy, in descending order of preference, as State policy: volume reduction at the source; recycling and reuse; combustion

255

Waste-to-Energy using Refuse-Derived Fuel  

Science Journals Connector (OSTI)

At a mass-burn incinerator, Municipal Solid Waste (MSW) is ... vehicles or waste collection vehicles into a deep pit. There is no processing of the waste. Waste is removed from the pit by overhead crane and fed i...

Floyd Hasselriis MME; Dr. Patrick F. Mahoney

2012-01-01T23:59:59.000Z

256

Waste-to-Energy using Refuse-Derived Fuel  

Science Journals Connector (OSTI)

At a mass-burn incinerator, Municipal Solid Waste (MSW) is ... vehicles or waste collection vehicles into a deep pit. There is no processing of the waste. Waste is removed from the pit by overhead crane and fed i...

Floyd Hasselriis MME; Dr. Patrick F. Mahoney

2013-01-01T23:59:59.000Z

257

Evaluation of HC1 measurement techniques at municipal and hazardous-waste incinerators  

SciTech Connect

Hydrogen chloride (HC1) emissions from hazardous waste incinerators are regulated by the EPA, and the Agency is considering HC1 regulations for municipal waste combustors. Until recently, techniques to adequately quantify these emissions using either instrumentation or wet-chemistry sampling methods have not been evaluated. The EPA has sponsored several field tests to assess the performance of commercially-available HC1 continuous emission monitoring systems (CEMS's) and a proposed manual sampling and analysis methodology for use at municipal and hazardous waste incinerators. Tests were performed (1) to determine the capability of HC1 CEMS's to provide valid measurement data, (2) to develop HC1 CEMS performance specifications, and (3) to develop a suitable performance test method.

Shanklin, S.A.; Steinsberger, S.C.; Logan, T.J.; Rollins, R.

1990-01-01T23:59:59.000Z

258

Feasibility Study on Solid Waste to Energy Technological Aspects  

E-Print Network (OSTI)

Feasibility Study on Solid Waste to Energy Technological Aspects Yuzhong Tan College of Engineering://www.funginstitute.berkeley.edu/sites/default/ les/SolidWasteToEnergy.pdf April 15, 2013 130 Blum Hall #5580 Berkeley, CA 94720-5580 | (510) 664 seeks to compare and evaluate each technology by reviewing waste to energy reports and seeking

Sekhon, Jasjeet S.

259

Clean solid biofuel production from high moisture content waste biomass employing hydrothermal treatment  

Science Journals Connector (OSTI)

Abstract Our society currently faces three challenges, including resource depletion, waste accumulation and environmental degradation, leading to rapidly escalating raw material costs and increasingly expensive and restrictive waste disposal legislation. This work aims to produce clean solid biofuel from high moisture content waste biomass (bio-waste) with high nitrogen (N)/chlorine (Cl) content by mild hydrothermal (HT) conversion processes. The newest results are summarized and discussed in terms of the mechanical dewatering and upgrading, dechlorination, denitrification and coalification resulting from the HT pretreatment. Moreover, both the mono-combustion and co-combustion characteristics of the solid fuel are reviewed by concentrating on the pollutants emission control, especially the NO emission properties. In addition, the feasibility of this HT solid biofuel production process is also discussed in terms of “Energy Balance and economic viability”. As an alternative to dry combustion/dry pyrolysis/co-combustion, the HT process, combining the dehydration and decarboxylation of a biomass to raise its carbon content aiming to achieve a higher calorific value, opens up the field of potential feedstock for lignite-like solid biofuel production from a wide range of nontraditional renewable and plentiful wet agricultural residues, sludge and municipal wastes. It would contribute to a wider application of HT pretreatment bio-wastes for safe disposal and energy recycling.

Peitao Zhao; Yafei Shen; Shifu Ge; Zhenqian Chen; Kunio Yoshikawa

2014-01-01T23:59:59.000Z

260

Identification of solid wastes in geothermal operations  

SciTech Connect

Regulations governing the disposal of hazardous wastes led to an assessment for geothermal solid wastes for potentially hazardous characteristics. Samples were collected from three active geothermal sites in the western United States: The Geysers, Imperial Valley, and northwestern Nevada. Approximately 20 samples were analyzed for corrosivity, EP toxicity, radioactivity, and bioaccumulation potential. The samples were further characterized by analysis for cations, anions, moisture content, priority pollutants, and additional trace metals in the leachate. In addition, an aqueous extraction was conducted at ambient pH. None of the samples collected at The Geysers or northwestern Nevada could be classified as hazardous as defined by the RCRA regulations published May 19, 1980 in the Federal Register. However, several samples from the Imperial Valley could be classified as hazardous. These hazardous characteristics appear to be related to the high salinity of geothermal fluids in that order. This study characterized samples from a limited geographical area and results cannot be extrapolated to other geothermal resource areas.

Hagmann, E.L.; Minicucci, D.D.; Wolbach, C.D.

1981-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

E-Print Network 3.0 - assessment waste characterization Sample...  

NLE Websites -- All DOE Office Websites (Extended Search)

5 > >> 41 Composition of Municipal Solid Waste-Need for Thermal Treatment in the present Indian context Summary: of estimating heat value of municipal wastes, from the view point...

262

The effect of developing nations' municipal waste composition on PCDD/PCDF emissions from open burning  

Science Journals Connector (OSTI)

Abstract Open burning tests of municipal waste from two countries, Mexico and China, showed composition-related differences in emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDDs/PCDFs). Twenty-six burn tests were conducted, comparing results from two laboratory combustion facilities. Waste was shredded to isolate composition-specific effects from those due to random waste orientation. Emissions ranged from 5 to 780 ng toxic equivalent/kg carbon burned (ng TEQ (kg Cb)?1) with an average of 140 ng TEQ (kg Cb)?1 (stdev = 170). The waste from Mexico (17 ng TEQ (kg Cb)?1) had a statistically lower average emission factor than waste from China (240 ng TEQ (kg Cb)?1. This difference was attributed primarily to waste composition differences, although one time-integrated combustion quality measure, ?CO/?CO2, showed statistical significance between laboratories. However, waste composition differences were far more determinant than which laboratory conducted the tests, illustrated using both statistical techniques and comparison of cross-over samples (wastes tested at both facilities). Comparison of emissions from previous waste combustion tests in Sweden and the U.S.A, showed emission factors within the range of those determined for Mexico and China waste. For laboratory-scale combustion, existing emission factors and test methodologies are generally applicable to both developed and developing countries.

Lisa Lundin; Brian Gullett; William F. Carroll Jr.; Abderrahmane Touati; Stellan Marklund; Heidelore Fiedler

2013-01-01T23:59:59.000Z

263

Hanford Site Solid Waste Acceptance Program - Hanford Site  

NLE Websites -- All DOE Office Websites (Extended Search)

About Us > Hanford Site Wide Programs > Hanford Site Solid Waste Acceptance Program About Us Hanford Overview and History Hanford Cleanup Hanford Site Wide Programs Hanford Site...

264

Wilders Grove Solid Waste Services Center | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Grove Solid Waste Services Center Project objective: Provide demonstration of Geothermal Heat Pumps viability on energy usage for future Service Centers planned by the City of...

265

Energy Secretary Bodman Statement on Hanford Solid Waste Settlement...  

Energy Savers (EERE)

will lead to a final order and the dismissal of the challenge to Hanford's Solid Waste Environmental Impact Statement (EIS) in the lawsuit Washington v. Bodman. DOE, with...

266

Characterization of urban solid waste in Chihuahua, Mexico  

Science Journals Connector (OSTI)

The characterization of urban solid waste generation is fundamental for adequate decision making in the management strategy of urban solid waste in a city. The objective of this study is to characterize the waste generated in the households of Chihuahua city, and to compare the results obtained in areas of the city with three different socioeconomic levels. In order to identify the different socioeconomic trends in waste generation and characterization, 560 samples of solid waste were collected during 1 week from 80 households in Chihuahua and were hand sorted and classified into 15 weighted fractions. The average waste generation in Chihuahua calculated in this study was 0.676 kg per capita per day in April 2006. The main fractions were: organic (48%), paper (16%) and plastic (12%). Results show an increased waste generation associated with the socioeconomic level. The characterization in amount and composition of urban waste is the first step needed for the successful implementation of an integral waste management system.

Guadalupe Gomez; Montserrat Meneses; Lourdes Ballinas; Francesc Castells

2008-01-01T23:59:59.000Z

267

Title 18 Alaska Administrative Code Chapter 60 Solid Waste Management...  

Open Energy Info (EERE)

Solid Waste Management Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: Title 18 Alaska Administrative Code Chapter 60 Solid...

268

Boiler tube failures in municipal waste-to-energy plants  

SciTech Connect

Waste-to-energy plants experienced increased boiler tube failures when the design changed from waste-heat boilers to radiant furnace waterwalls using superheat. Fireside attack by chlorine and sulfur compounds in refuse combustion products caused many forced outages in early European plants operating at high steam temperatures and pressures. Despite conservative steam conditions in the first US plants, failures occurred. As steam temperatures increased, corrosion problems multiplied. The problems have been alleviated by covering the waterwalls with either refractory or weld overlays of nickel-based alloys and using high nickel-chromium alloys for superheater tubes. Changes in furnace design to provide uniform combustion and avoid reducing conditions in the waterwall zone and to lower the gas temperature in the superheater also have helped minimize corrosion.

Krause, H.H.; Wright, I.G. [Battelle, Columbus, OH (United States)

1996-01-01T23:59:59.000Z

269

Ammonia fiber explosion (AFEX) pretreatment of municipal solid waste components  

E-Print Network (OSTI)

as follows: Combine 50 mL pH 4. 6 1. 0 M citrate buffer 500 mL distilled H, O 1. 8939 g Genencor 300P cellulase or Cytolase 300 5. 695 mL NOVOZYM Beta-glucosidase 03 g sodium azide Complete to 1 L with HrO Adjust pH to 4. 8 with 1. 0 M Na... is found in Appendix 8. 2. Novozym 188 cellobiose with an activity of 250 CBU/mL was added giving a loading of 285 CBU/g dry substrate. Both enzymes contain some sugars that must be subtracted from the sugar yields. A complete procedure is given...

Lundeen, Joseph Eric

2012-06-07T23:59:59.000Z

270

Clean energy from municipal solid waste. Final report  

SciTech Connect

The aim of the project was to demonstrate the environmental and combustion performance advantages of a carbonized refuse derived fuel (RDF) slurry, produced from EnerTech`s slurry carbonization process, using continuous pilot scale equipment and its suitability as an alternative fuel for utility and industrial boilers.

Klosky, M.

1997-01-01T23:59:59.000Z

271

Gaseous missions rduction from arobic MBT of municipal solid waste  

E-Print Network (OSTI)

recovery (by collecting biogas generated during anaerobic digestion) and/or return of organic matter the composting process, and the sec- ond one focused on the biogas génération from the associated landfill surface fluxes and biogas composition. ineris-00973342,version1-4Apr2014 Author manuscript, published

Boyer, Edmond

272

Kinematic wave model for water movement in municipal solid waste  

E-Print Network (OSTI)

conductivity and capillary potential suggested by Clapp and Hornberger [1978] have been employed. However, as pointed out by Bendz et at. (1997), the process assumptions on which the Richards equation and the ensuing CDE rely for their applicability have... and Environ- mental Impact, edited by T. H. Christensen, R. Cossu, and R. Steg- mann, pp. 29-49, Academic, San Diego, Calif., 1989. Clapp, R. B., and G. M. Hornberger, Empirical equations for some soil hydraulic properties, Water Resour. Res., 14, 601...

Bendz, David; Singh, Vijay P.; Rosqvist, H??kan; Bengtsson, Lars

273

Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume...  

Energy Savers (EERE)

Synthesis, Volume 2: A Techno-economic Evaluation of the Production of Mixed Alcohols Biomass is a renewable energy resource that can be converted into liquid fuel suitable for...

274

The Economics of Resource Recovery from Municipal Solid Waste  

Science Journals Connector (OSTI)

...Eq. 2 when the unrecovered fraction is disposed of by incineration...worth of resource recovery in light of other demands such as those...Utilization of the Organic Fraction Figure 4 shows that 47 percent...that the value of the organic fraction as a fuel exactly offsets the...

James G. Abert; Harvey Alter; J. Frank Bernheisel

1974-03-15T23:59:59.000Z

275

Integrated Plant for the Municipal Solid Waste of Madrid  

E-Print Network (OSTI)

such as steam- boiler water treatment, compressed-air, control and instrumentation, etc. The incinerator of the project was to recover the energy content of RDF generated by the recycling plant of the city of Madrid and Composting Plant The MSW is brought by the collecting trucks which unload in the storage area with a two

Columbia University

276

Modeling of leachate generation in municipal solid waste landfills  

E-Print Network (OSTI)

parameters specified by the user. Ultimately, this model will strive to replace the time the user requires to generate and fill a given landfill geometry with time spent running and evaluating trials to yield the best design....

Beck, James Bryan

2012-06-07T23:59:59.000Z

277

EA-1707: Closure of Nonradioactive Dangerous Waste Landfill and Solid Waste  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

07: Closure of Nonradioactive Dangerous Waste Landfill and 07: Closure of Nonradioactive Dangerous Waste Landfill and Solid Waste Landfill, Hanford Site, Richland, Washington EA-1707: Closure of Nonradioactive Dangerous Waste Landfill and Solid Waste Landfill, Hanford Site, Richland, Washington Summary This EA evaluates the potential environmental impacts of closing the Nonradioactive Dangerous Waste Landfill and the Solid Waste Landfill. The Washington State Department of Ecology is a cooperating agency in preparing this EA. Public Comment Opportunities None available at this time. Documents Available for Download August 26, 2011 EA-1707: Revised Draft Environmental Assessment Closure of Nonradioactive Dangerous Waste Landfill and Solid Waste Landfill, Hanford Site, Richland, Washington May 13, 2010 EA-1707: Draft Environmental Assessment

278

Vitrified municipal waste as a host form for high-level nuclear waste  

Science Journals Connector (OSTI)

Using glass as a safe and long term hosting matrix for hazardous wastes and for the immobilization of heavy metals and nuclear wastes has become an attractive method [3]. The most known glasses used as nuclear waste

N. A. El-Alaily; E. M. Abou-Hussein…

2014-01-01T23:59:59.000Z

279

Solid Waste at Williams College A Luce Foundation Report  

E-Print Network (OSTI)

's environmental sustainability. As a step toward understanding Williams College's environmental impact, I spentSolid Waste at Williams College A Luce Foundation Report Katherine S. White September 2007 Inside a Williams trash can SUMMARY Solid waste at Williams College can be separated into three general categories

Aalberts, Daniel P.

280

IGES GHG Calculator For Solid Waste | Open Energy Information  

Open Energy Info (EERE)

IGES GHG Calculator For Solid Waste IGES GHG Calculator For Solid Waste Jump to: navigation, search LEDSGP green logo.png FIND MORE DIA TOOLS This tool is part of the Development Impacts Assessment (DIA) Toolkit from the LEDS Global Partnership. Tool Summary Name: IGES GHG Calculator For Solid Waste Agency/Company /Organization: Institute for Global Environmental Strategies (IGES) Sector: Climate, Energy Complexity/Ease of Use: Simple Cost: Free Related Tools Energy Development Index (EDI) Harmonized Emissions Analysis Tool (HEAT) Electricity Markets Analysis (EMA) Model ... further results A simple spreadsheet model for calculating greenhouse gas emissions from existing waste management practices (transportation, composting, anaerobic digestion, mechanical biological treatment, recycling, landfilling) in

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Delivery system for molten salt oxidation of solid waste  

DOE Patents (OSTI)

The present invention is a delivery system for safety injecting solid waste particles, including mixed wastes, into a molten salt bath for destruction by the process of molten salt oxidation. The delivery system includes a feeder system and an injector that allow the solid waste stream to be accurately metered, evenly dispersed in the oxidant gas, and maintained at a temperature below incineration temperature while entering the molten salt reactor.

Brummond, William A. (Livermore, CA); Squire, Dwight V. (Livermore, CA); Robinson, Jeffrey A. (Manteca, CA); House, Palmer A. (Walnut Creek, CA)

2002-01-01T23:59:59.000Z

282

EA-1707: Closure of Nonradioactive Dangerous Waste Landfill and Solid Waste Landfill, Hanford Site, Richland, Washington  

Energy.gov (U.S. Department of Energy (DOE))

This EA evaluates the potential environmental impacts of closing the Nonradioactive Dangerous Waste Landfill and the Solid Waste Landfill. The Washington State Department of Ecology is a cooperating agency in preparing this EA.

283

Advanced thermal processing alternatives for solid waste management  

SciTech Connect

The 1990`s have seen a resurgence of interest in the development of new thermal processing alternatives for municipal solid waste (MSW). Sparked by increasingly stringent environmental regulations, much of this creative energy has been applied to technologies for the gasification of MSW: converting the solid, hard to handle material into a clean, medium to high-Btu fuel gas. Other developers have focussed on full combustion technology but with a {open_quotes}twist{close_quotes} that lowers emissions or reduces cost. A comprehensive study of these new technologies was recently completed under the sponsorship of the National Renewable Energy Laboratory of the U.S. Department of Energy. The study characterized the state-of-the-art among emerging MSW thermal processing technologies that have reached the point of `incipient commercialization.` More than 45 technologies now under development were screened to develop a short list of seven processes that have passed through the idea stage, laboratory and benchscale testing, and have been prototyped at an MSW feed rate of at least several tons per hour. In-depth review of these seven included inspections of operating pilot or prototype units and a detailed analysis of technical, environmental and economic feasibility issues. No attempt was made to select `the best` technology since best can only be defined in the context of the constraints, aspirations and circumstances of a specific, local situation. The basic flowsheet, heat and material balances and available environmental data were summarized to help the reader grasp the underlying technical concepts and their embodiment in hardware. Remaining development needs, as seen by the study team are presented. Economic analysis shows the general balance of capital and operating costs.

Niessen, W.R. [Camp Dresser & McKee Inc., Cambridge, MA (United States)

1997-12-01T23:59:59.000Z

284

Solid waste retrieval. Phase 1, Operational basis  

SciTech Connect

This Document describes the operational requirements, procedures, and options for execution of the retrieval of the waste containers placed in buried storage in Burial Ground 218W-4C, Trench 04 as TRU waste or suspect TRU waste under the activity levels defining this waste in effect at the time of placement. Trench 04 in Burial Ground 218W-4C is totally dedicated to storage of retrievable TRU waste containers or retrievable suspect TRU waste containers and has not been used for any other purpose.

Johnson, D.M.

1994-09-30T23:59:59.000Z

285

Energy Secretary Bodman Statement on Hanford Solid Waste Settlement  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Secretary Bodman Statement on Hanford Solid Waste Settlement Energy Secretary Bodman Statement on Hanford Solid Waste Settlement Agreement Energy Secretary Bodman Statement on Hanford Solid Waste Settlement Agreement January 9, 2006 - 9:43am Addthis Richland, WA - U.S. Secretary of Energy Samuel Bodman today announced that the Department of Energy (DOE) and the State of Washington have entered into a settlement agreement that will lead to a final order and the dismissal of the challenge to Hanford's Solid Waste Environmental Impact Statement (EIS) in the lawsuit Washington v. Bodman. DOE, with Washington State as a cooperating agency, will prepare a new EIS that will include updated, site-wide groundwater analysis. "With this agreement, both parties will be able to shift their focus and resources away from litigation and toward partnership and our shared

286

Energy Secretary Bodman Statement on Hanford Solid Waste Settlement  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Statement on Hanford Solid Waste Settlement Statement on Hanford Solid Waste Settlement Agreement Energy Secretary Bodman Statement on Hanford Solid Waste Settlement Agreement January 9, 2006 - 9:43am Addthis Richland, WA - U.S. Secretary of Energy Samuel Bodman today announced that the Department of Energy (DOE) and the State of Washington have entered into a settlement agreement that will lead to a final order and the dismissal of the challenge to Hanford's Solid Waste Environmental Impact Statement (EIS) in the lawsuit Washington v. Bodman. DOE, with Washington State as a cooperating agency, will prepare a new EIS that will include updated, site-wide groundwater analysis. "With this agreement, both parties will be able to shift their focus and resources away from litigation and toward partnership and our shared

287

Proof of Proper Solid Waste Disposal (West Virginia)  

Energy.gov (U.S. Department of Energy (DOE))

This rule provides guidance to persons occupying a residence or operating a business establishment in this state regarding the approved method of providing proof of proper solid waste disposal to...

288

State Solid Waste Management and Resource Recovery Plan (Montana)  

Energy.gov (U.S. Department of Energy (DOE))

The State supports the "good management of solid waste and the conservation of natural resources through the promotion or development of systems to collect, separate, reclaim, recycle, and dispose...

289

Hawaii DOH Solid Waste Section Webpage | Open Energy Information  

Open Energy Info (EERE)

Section Webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Hawaii DOH Solid Waste Section Webpage Abstract This webpage provides an overview of...

290

Pilot-scale anaerobic co-digestion of municipal biomass waste and waste activated sludge in China: Effect of organic loading rate  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Co-digestion of municipal biomass waste (MBW) and waste activated sludge (WAS) was examined on a pilot-scale reactor. Black-Right-Pointing-Pointer System performance and stability under OLR of 1.2, 2.4, 3.6, 4.8, 6.0 and 8.0 kg VS (m{sup 3} d){sup -1} were analyzed. Black-Right-Pointing-Pointer A maximum methane production rate of 2.94 m{sup 3} (m{sup 3} d){sup -1} was achieved at OLR of 8.0 kg VS (m{sup 3} d){sup -1} and HRT of 15d. Black-Right-Pointing-Pointer With the increasing OLRs, pH values, VS removal rate and methane concentration decreased and VFA increased. Black-Right-Pointing-Pointer The changing of biogas production rate can be a practical approach to monitor and control anaerobic digestion system. - Abstract: The effects of organic loading rate on the performance and stability of anaerobic co-digestion of municipal biomass waste (MBW) and waste activated sludge (WAS) were investigated on a pilot-scale reactor. The results showed that stable operation was achieved with organic loading rates (OLR) of 1.2-8.0 kg volatile solid (VS) (m{sup 3} d){sup -1}, with VS reduction rates of 61.7-69.9%, and volumetric biogas production of 0.89-5.28 m{sup 3} (m{sup 3} d){sup -1}. A maximum methane production rate of 2.94 m{sup 3} (m{sup 3} d){sup -1} was achieved at OLR of 8.0 kg VS (m{sup 3} d){sup -1} and hydraulic retention time of 15 days. With increasing OLRs, the anaerobic reactor showed a decrease in VS removal rate, average pH value and methane concentration, and a increase of volatile fatty acid concentration. By monitoring the biogas production rate (BPR), the anaerobic digestion system has a higher acidification risk under an OLR of 8.0 kg VS (m{sup 3} d){sup -1}. This result remarks the possibility of relating bioreactor performance with BPR in order to better understand and monitor anaerobic digestion process.

Liu Xiao, E-mail: liuxiao07@mails.tsinghua.edu.cn [School of Environment, Tsinghua University, Beijing 100084 (China); Wang Wei; Shi Yunchun; Zheng Lei [School of Environment, Tsinghua University, Beijing 100084 (China); Gao Xingbao [Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); Qiao Wei [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Zhou Yingjun [Department of Urban and Environmental Engineering, Graduate School of Engineering, Kyoto University, Katsura, Nisikyo-ku, Kyoto 615-8540 (Japan)

2012-11-15T23:59:59.000Z

291

Hanford Site solid waste acceptance criteria  

SciTech Connect

Order 5820.2A requires that each treatment, storage, and/or disposal facility (referred to in this document as TSD unit) that manages low-level or transuranic waste (including mixed waste and TSCA PCB waste) maintain waste acceptance criteria. These criteria must address the various requirements to operate the TSD unit in compliance with applicable safety and environmental requirements. This document sets forth the baseline criteria for acceptance of radioactive waste at TSD units operated by WMH. The criteria for each TSD unit have been established to ensure that waste accepted can be managed in a manner that is within the operating requirements of the unit, including environmental regulations, DOE Orders, permits, technical safety requirements, waste analysis plans, performance assessments, and other applicable requirements. Acceptance criteria apply to the following TSD units: the Low-Level Burial Grounds (LLBG) including both the nonregulated portions of the LLBG and trenches 31 and 34 of the 218-W-5 Burial Ground for mixed waste disposal; Central Waste Complex (CWC); Waste Receiving and Processing Facility (WRAP); and T Plant Complex. Waste from all generators, both from the Hanford Site and from offsite facilities, must comply with these criteria. Exceptions can be granted as provided in Section 1.6. Specific waste streams could have additional requirements based on the 1901 identified TSD pathway. These requirements are communicated in the Waste Specification Records (WSRds). The Hanford Site manages nonradioactive waste through direct shipments to offsite contractors. The waste acceptance requirements of the offsite TSD facility must be met for these nonradioactive wastes. This document does not address the acceptance requirements of these offsite facilities.

Ellefson, M.D.

1998-07-01T23:59:59.000Z

292

Solid Recovered Fuel: Influence of Waste Stream Composition and Processing on Chlorine Content and Fuel Quality  

Science Journals Connector (OSTI)

Solid recovered fuel (SRF) produced by mechanical–biological treatment (MBT) of municipal waste can replace fossil fuels, being a CO2-neutral, affordable, and alternative energy source. ... (4) The concentration of chlorine in SRF is key to fuel quality due to concern that elevated concentrations could exacerbate ash deposition in the convective part of boilers;(8) cause high-temperature corrosion (>500 °C) of boiler steel due to alkali chlorides and lower temperature melt deposits (300–400 °C) in the presence of zinc and lead;(9) generate high acid gases emissions (hydrogen chloride (HCl));(10) and contribute to the formation of polychlorinated dibenzodioxins (PCDDs) (for [Cl] above 0.3% w/wd)(11) during thermal recovery. ... The overall moisture content MT, reported as % w/wd (d: dry solids), was measured in two steps. ...

Costas Velis; Stuart Wagland; Phil Longhurst; Bryce Robson; Keith Sinfield; Stephen Wise; Simon Pollard

2011-12-21T23:59:59.000Z

293

Event:World Solid Waste Congress 2012 | Open Energy Information  

Open Energy Info (EERE)

Solid Waste Congress 2012 Solid Waste Congress 2012 Jump to: navigation, search Calendar.png World Solid Waste Congress 2012: on 2012/09/17 During the three days of this Congress you can meet academics presenting cutting edge research; scientists, government administrators and decision makers, representatives of the world's largest companies in the waste sector, and many other practitioners too from small and medium enterprises. Florence 2012: where else in the world can you network with these people in such a short time The Congress location is at the Palazzo dei Congressi adjacent to the Santa Maria Novella mainline railway station in the City center. ATIA-ISWA ITALIA is also organising a series of events in Italy leading to the main Congress this year. This beautiful city will also host

294

Solid waste education in children's museums  

E-Print Network (OSTI)

before it is generated. The concept behind this strategy is that if we can eliminate the waste, we can decrease disposal problems, Similarly, recycling and composting are solutions to extending the life of resources by reusing them instead of throwing... waste management. This strategy involves a hierarchy of solutions, with source reduction as the best solution, followed by recycling, to include composting, as the second best option, and waste combustion and landfllling as the last two means...

King, Jennifer Campbell

1997-01-01T23:59:59.000Z

295

Solid Waste Regulations (Nova Scotia, Canada)  

Energy.gov (U.S. Department of Energy (DOE))

Nova Scotia Environment administers waste management for the province. Regulations include specific rules and standards for landfills, establish a Resource Recovery Fund, and guidelines for...

296

Heating and cooling of municipal buildings with waste heat from ground water  

SciTech Connect

The feasibility of using waste heat from municipal water wells to replace natural gas for heating of the City Hall, Fire Station, and Community Hall in Wilmer, Texas was studied. At present, the 120/sup 0/F well water is cooled by dissipating the excess heat through evaporative cooling towers before entering the distribution system. The objective of the study was to determine the pumping cycle of the well and determine the amount of available heat from the water for a specified period. This data were correlated with the heating and cooling demand of the City's buildings, and a conceptual heat recovery system will be prepared. The system will use part or all of the excess heat from the water to heat the buildings, thereby eliminating the use of natural gas. The proposed geothermal retrofit of the existing natural gas heating system is not economical because the savings in natural gas does not offset the capital cost of the new equipment and the annual operating and maintenance costs. The fuel savings and power costs are a virtual trade-off over the 25-year period. The installation and operation of the system was estimated to cost $105,000 for 25 years which is an unamortized expense. In conclusion, retrofitting the City of Wilmer's municipal buildings is not feasible based on the economic analysis and fiscal projections as presented.

Morgan, D.S.; Hochgraf, J.

1980-10-01T23:59:59.000Z

297

International Solid Waste Association (ISWA) | Open Energy Information  

Open Energy Info (EERE)

Waste Association (ISWA) Waste Association (ISWA) Jump to: navigation, search Name International Solid Waste Association (ISWA) Address ISWA - International Solid Waste Association General Secretariat Auerspergstrasse 15, Top 41 1080 Vienna Austria Place Vienna Austria Website http://www.iswa.org/ Coordinates 48.2088365°, 16.3546602° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":48.2088365,"lon":16.3546602,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

298

CSER 95-007 Acceptability of Bettis Lab Waste Shipment to WHC Solid Waste  

SciTech Connect

The purpose of this document is to evaluate a potential discrepancy between the Solid Waste Management (SWM) criticality prevention specifications and a proposed receipt from Bettis Laboratories. The analysis has been performed to determine the acceptability of the Bettis Laboratories waste container with respect to SWM criticality requirements.

MILLER, E.M.

1999-12-03T23:59:59.000Z

299

NEW SOLID FUELS FROM COAL AND BIOMASS WASTE  

SciTech Connect

Under DOE sponsorship, McDermott Technology, Inc. (MTI), Babcock and Wilcox Company (B and W), and Minergy Corporation developed and evaluated a sludge derived fuel (SDF) made from sewage sludge. Our approach is to dry and agglomerate the sludge, combine it with a fluxing agent, if necessary, and co-fire the resulting fuel with coal in a cyclone boiler to recover the energy and to vitrify mineral matter into a non-leachable product. This product can then be used in the construction industry. A literature search showed that there is significant variability of the sludge fuel properties from a given wastewater plant (seasonal and/or day-to-day changes) or from different wastewater plants. A large sewage sludge sample (30 tons) from a municipal wastewater treatment facility was collected, dried, pelletized and successfully co-fired with coal in a cyclone-equipped pilot. Several sludge particle size distributions were tested. Finer sludge particle size distributions, similar to the standard B and W size distribution for sub-bituminous coal, showed the best combustion and slagging performance. Up to 74.6% and 78.9% sludge was successfully co-fired with pulverized coal and with natural gas, respectively. An economic evaluation on a 25-MW power plant showed the viability of co-firing the optimum SDF in a power generation application. The return on equity was 22 to 31%, adequate to attract investors and allow a full-scale project to proceed. Additional market research and engineering will be required to verify the economic assumptions. Areas to focus on are: plant detail design and detail capital cost estimates, market research into possible project locations, sludge availability at the proposed project locations, market research into electric energy sales and renewable energy sales opportunities at the proposed project location. As a result of this program, wastes that are currently not being used and considered an environmental problem will be processed into a renewable fuel. These fuels will be converted to energy while reducing CO{sub 2} emissions from power generating boilers and mitigating global warming concerns. This report describes the sludge analysis, solid fuel preparation and production, combustion performance, environmental emissions and required equipment.

Hamid Farzan

2001-09-24T23:59:59.000Z

300

Solid waste drum array fire performance  

SciTech Connect

Fire hazards associated with drum storage of radioactively contaminated waste are a major concern in DOE waste storage facilities. This report is the second of two reports on fire testing designed to provide data relative to the propagation of a fire among storage drum arrays. The first report covers testing of individual drums subjected to an initiating fire and the development of the analytical methodology to predict fire propagation among storage drum arrays. This report is the second report, which documents the results of drum array fire tests. The purpose of the array tests was to confirm the analytical methodology developed by Phase I fire testing. These tests provide conclusive evidence that fire will not propagate from drum to drum unless an continuous fuel source other than drum contents is provided.

Louie, R.L. [Westinghouse Hanford Co., Richland, WA (United States); Haecker, C.F. [Los Alamos Technical Associates, Inc., Kennewick, WA (United States); Beitel, J.J.; Gottuck, D.T.; Rhodes, B.T.; Bayier, C.L. [Hughes Associates, Inc., Baltimore, MD (United States)

1995-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Recycling Realities: ASU's Quest for Zero Solid Waste  

E-Print Network (OSTI)

Recycling Realities: ASU's Quest for Zero Solid Waste Dawn RatcliffePast Recycling Coordinator Alana LevineRecycling Program Manager For the last 16 years, Dawn Ratcliffe has worked and volunteered in the sustainability and animal-advocacy fields. She has organized several Earth Day events, recycling events

Zhang, Junshan

302

IDAPA 58.01.06 - Solid Waste Management Rules and Standards ...  

Open Energy Info (EERE)

Solid Waste Management Rules and Standards Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: IDAPA 58.01.06 - Solid Waste...

303

LOW ACTIVITY WASTE FEED SOLIDS CARACTERIZATION AND FILTERABILITY TESTS  

SciTech Connect

The primary treatment of the tank waste at the DOE Hanford site will be done in the Waste Treatment and Immobilization Plant (WTP) that is currently under construction. The baseline plan for the WTP Pretreatment facility is to treat the waste, splitting it into High Level Waste (HLW) feed and Low Activity Waste (LAW) feed. Both waste streams are then separately vitrified as glass and sealed in canisters. The LAW glass will be disposed onsite in the Integrated Disposal Facility (IDF). There are currently no plans to treat the waste to remove technetium in the WTP Pretreatment facility, so its disposition path is the LAW glass. Options are being explored to immobilize the LAW portion of the tank waste, i.e., the LAW feed from the WTP Pretreatment facility. Removal of {sup 99}Tc from the LAW Feed, followed by off-site disposal of the {sup 99}Tc, would eliminate a key risk contributor for the IDF Performance Assessment (PA) for supplemental waste forms, and has potential to reduce treatment and disposal costs. Washington River Protection Solutions (WRPS) is developing some conceptual flow sheets for LAW treatment and disposal that could benefit from technetium removal. One of these flowsheets will specifically examine removing {sup 99}Tc from the LAW feed stream to supplemental immobilization. The conceptual flow sheet of the {sup 99}Tc removal process includes a filter to remove insoluble solids prior to processing the stream in an ion exchange column, but the characteristics and behavior of the liquid and solid phases has not previously been investigated. This report contains results of testing of a simulant that represents the projected composition of the feed to the Supplemental LAW process. This feed composition is not identical to the aqueous tank waste fed to the Waste Treatment Plant because it has been processed through WTP Pretreatment facility and therefore contains internal changes and recycle streams that will be generated within the WTP process. Although a Supplemental LAW feed simulant has previously been prepared, this feed composition differs from that simulant because those tests examined only the fully soluble aqueous solution at room temperature, not the composition formed after evaporation, including the insoluble solids that precipitate after it cools. The conceptual flow sheet for Supplemental LAW immobilization has an option for removal of {sup 99}Tc from the feed stream, if needed. Elutable ion exchange has been selected for that process. If implemented, the stream would need filtration to remove the insoluble solids prior to processing in an ion exchange column. The characteristics, chemical speciation, physical properties, and filterability of the solids are important to judge the feasibility of the concept, and to estimate the size and cost of a facility. The insoluble solids formed during these tests were primarily natrophosphate, natroxalate, and a sodium aluminosilicate compound. At the elevated temperature and 8 M [Na+], appreciable insoluble solids (1.39 wt%) were present. Cooling to room temperature and dilution of the slurry from 8 M to 5 M [Na+] resulted in a slurry containing 0.8 wt% insoluble solids. The solids (natrophosphate, natroxalate, sodium aluminum silicate, and a hydrated sodium phosphate) were relatively stable and settled quickly. Filtration rates were in the range of those observed with iron-based simulated Hanford tank sludge simulants, e.g., 6 M [Na+] Hanford tank 241-AN-102, even though their chemical speciation is considerably different. Chemical cleaning of the crossflow filter was readily accomplished with acid. As this simulant formulation was based on an average composition of a wide range of feeds using an integrated computer model, this exact composition may never be observed. But the test conditions were selected to enable comparison to the model to enable improving its chemical prediction capability.

McCabe, D.; Crawford, C.; Duignan, M.; Williams, M.; Burket, P.

2014-04-03T23:59:59.000Z

304

Solid waste energy recovery for brackish water desalination  

SciTech Connect

Introduced is the concept of combining solid-waste energy recovery with brackish water desalination for water supply improvement. The history of such plants is briefly detailed, and performance and operating cost data of several existing desalination plants is given. It is concluded that the combination of solid waste energy recovery utilizing modular combustion units and brackish water desalination using the reverse osmosis process can cancel out the energy-related negative aspects of both technologies. Furthermore, with innovative planning and adequate political, financial and technical leadership, communities that meet criteria outlined in the report can convert a waste disposal problem into a resource for the betterment of the community and its surrounding neighbors.

Bailie, R.E.

1982-07-01T23:59:59.000Z

305

Method of draining water through a solid waste site without leaching  

DOE Patents (OSTI)

The present invention is a method of preventing water from leaching solid waste sites by preventing atmospheric precipitation from contacting waste as the water flows through a solid waste site. The method comprises placing at least one drain hole through the solid waste site. The drain hole is seated to prevent waste material from entering the drain hole, and the solid waste site cover material is layered and graded to direct water to flow toward the drain hole and to soil beneath the waste site.

Treat, R.L.; Gee, G.W.; Whyatt, G.A.

1993-02-02T23:59:59.000Z

306

Solid Waste as an Energy Source  

E-Print Network (OSTI)

. PROCESS The solLd waste energy conversion system bullt by Kelley Company consists of a combustion unit and an energy recovery boLler. The combustion unit uses a two stage process; the refuse is fLrst converted to gases by a pyrolysis process... wlll be conslderably lower than the temperature that woulq be achleved If stoichiometrlc air to fuel ratlo was malntained. The resulting temperatures In the pyrolysis chamber ranges from 1200 0 to 1500 o P. The low a lr lnput, as compared wlth...

Erlandsson, K. I.

1979-01-01T23:59:59.000Z

307

Quantification of greenhouse gas emissions from waste management processes for municipalities - A comparative review focusing on Africa  

SciTech Connect

The amount of greenhouse gases (GHG) emitted due to waste management in the cities of developing countries is predicted to rise considerably in the near future; however, these countries have a series of problems in accounting and reporting these gases. Some of these problems are related to the status quo of waste management in the developing world and some to the lack of a coherent framework for accounting and reporting of greenhouse gases from waste at municipal level. This review summarizes and compares GHG emissions from individual waste management processes which make up a municipal waste management system, with an emphasis on developing countries and, in particular, Africa. It should be seen as a first step towards developing a more holistic GHG accounting model for municipalities. The comparison between these emissions from developed and developing countries at process level, reveals that there is agreement on the magnitude of the emissions expected from each process (generation of waste, collection and transport, disposal and recycling). The highest GHG savings are achieved through recycling, and these savings would be even higher in developing countries which rely on coal for energy production (e.g. South Africa, India and China) and where non-motorized collection and transport is used. The highest emissions are due to the methane released by dumpsites and landfills, and these emissions are predicted to increase significantly, unless more of the methane is captured and either flared or used for energy generation. The clean development mechanism (CDM) projects implemented in the developing world have made some progress in this field; however, African countries lag behind.

Friedrich, Elena, E-mail: Friedriche@ukzn.ac.za [CRECHE Centre for Research in Environmental, Coastal and Hydrological Engineering, School of Civil Engineering, Surveying and Construction, University of KwaZulu-Natal, Howard College Campus, Durban (South Africa); Trois, Cristina [CRECHE Centre for Research in Environmental, Coastal and Hydrological Engineering, School of Civil Engineering, Surveying and Construction, University of KwaZulu-Natal, Howard College Campus, Durban (South Africa)

2011-07-15T23:59:59.000Z

308

Field study of disposed solid wastes from advanced coal processes  

SciTech Connect

Radian Corporation and the North Dakota Energy and Environmental Research Center (EERC) are funded to develop information to be used by private industry and government agencies for managing solid waste produced by advanced coal processes. This information will be developed by conducting several field studies on disposed wastes from these processes. Data will be collected to characterize these wastes and their interactions with the environments in which they are disposed. Three sites have been selected for the field studies: Colorado Ute's fluidized bed combustion (FBC) unit in Nucla, Colorado; Ohio Edison's limestone injection multistage burner (LIMB) retrofit in Lorain, Ohio; and Freeman United's site using waste from Midwest Grain's FBC unit in central Illinois. A fourth site is under consideration at the Dakota Gasification Company in North Dakota. The first two tasks of this project involved the development of test plans and obtaining site access.

Not Available

1990-01-01T23:59:59.000Z

309

Development of thermoelectric power generation system utilizing heat of combustible solid waste  

SciTech Connect

The paper presents the development of thermoelectric power generation system utilizing heat of municipal solid waste. The systematic classification and design guideline are proposed in consideration of the characteristics of solid waste processing system. The conceptual design of thermoelectric power generation system is carried out for a typical middle scale incinerator system (200 ton/day) by the local model. Totally the recovered electricity is 926.5 kWe by 445 units (569,600 couples). In order to achieve detailed design, one dimensional steady state model taking account of temperature dependency of the heat transfer performance and thermoelectric properties is developed. Moreover, small scale on-site experiment on 60 W class module installed in the real incinerator is carried out to extract various levels of technological problems. In parallel with the system development, high temperature thermoelectric elements such as Mn-Si and so on are developed aiming the optimization of ternary compound and high performance due to controlled fine-grain boundary effect. The manganese silicide made by shrinking-rate controlled sintering method performs 5 ({mu}W/cm K{cflx 2}) in power factor at 800 K. {copyright} {ital 1995} {ital American} {ital Institute} {ital of} {ital Physics}.

Kajikawa, T.; Ito, M.; Katsube, I. [Shonan Institute of Technology, Fujisawa, Kanagawa, 251 (Japan); Shibuya, E. [NKK Corporation, Yokohama, Kanagawa, 230 (Japan)

1994-08-10T23:59:59.000Z

310

Economic impact analysis for proposed emission standards and guidelines for municipal waste combustors: A description of the basis for, and impacts of, proposed revisions to air pollutant emission regulations for new and existing municipal waste combustors under Clean Air Act Sections 111(b), 111(d), and 129. Final report  

SciTech Connect

EPA is proposing revised and expanded air pollutant emission standards for new, and guidelines for existing, municipal waste combustors (MWCs), pursuant to Sections 111(b), 111(d), and 129 of the Clean Air Act of 1990. The regulations will replace or supplement those promulgated by EPA on February 11, 1991. The standards and guidelines will apply to MWCs with a capacity to combust 35 or more Mg of municipal solid waste per day. The pollutants to be regulated are particulate matter (total and fine), opacity, sulfur dioxide, hydrogen chloride, oxides of nitrogen, carbon monoxide, lead, cadmium mercury, and dibenzofurans and dioxins. The report describes the standards and guidelines, their potential economic impacts, and related matters. EPA estimates the national annual cost of the standards in 1994 will be $44 million, plus the cost of the 1991 standards, $157 million, for a total of $201 million. EPA estimates the equivalent cost of the guidelines at $280 million plus $168 million for a total of $448 million.

Jellicorse, B.L.; Dempsey, J.L.

1994-03-01T23:59:59.000Z

311

Summary of radioactive solid waste received in the 200 Areas during calendar year 1992  

SciTech Connect

Westinghouse Hanford Company manages and operates the Hanford Site 200 Area radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Field Office, under contract DE-AC06-87RL10930. These facilities include radioactive solid waste disposal sites and radioactive solid waste storage areas. This document summarizes the amount of radioactive materials that have been buried and stored in the 200 Area radioactive solid waste storage and disposal facilities since startup in 1944 through calendar year 1991. This report does not include solid radioactive wastes in storage or disposed of in other areas or facilities such as the underground tank farms, or backlog wastes. Unless packaged within the scope of WHC-EP-0063, Hanford Site Solid Waste Acceptance Criteria, (WHC 1988), liquid waste data are not included in this document.

Anderson, J.D.; Hagel, D.L.

1992-05-01T23:59:59.000Z

312

Summary of radioactive solid waste received in the 200 Areas during calendar year 1994  

SciTech Connect

Westinghouse Hanford Company manages and operates the Hanford Site 200 Area radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Field Office, under contract DE-AC06-87RL10930. These facilities include radioactive solid waste disposal sites and radioactive solid waste storage areas. This document summarizes the amount of radioactive material that has been buried and stored in the 200 Area radioactive solid waste storage and disposal facilities from startup in 1944 through calendar year 1994. This report does not include backlog waste: solid radioactive wastes in storage or disposed of in other areas or facilities such as the underground tank farms. Unless packaged within the scope of WHC-EP-0063, Hanford Site Solid Waste Acceptance Criteria (WHC 1988), liquid waste data are not included in this document.

Anderson, J.D.; Hagel, D.L.

1995-08-01T23:59:59.000Z

313

Summary of radioactive solid waste received in the 200 Areas during calendar year 1993  

SciTech Connect

Westinghouse Hanford Company manages and operates the Hanford Site 200 Areas radioactive solid waste storage and disposal facilities for the US Department of Energy, Richland Operations Office. These facilities include radioactive solid waste disposal sites and radioactive solid waste storage areas. This document summarizes the amount of radioactive materials that have been buried and stored in the 200 Areas radioactive solid waste storage and disposal facilities since startup in 1944 through calendar year 1993. This report does not include backlog waste, solid radioactive waste in storage or disposed of in other areas, or facilities such as the underground tank farms. Unless packaged within the scope of WHC-EP-0063, ``Hanford Site Solid Waste Acceptance Criteria,`` (WHC 1988), liquid waste data are not included in this document.

Anderson, J.D.; Hagel, D.L.

1994-09-01T23:59:59.000Z

314

Soil stabilization using oil-shale solid waste  

SciTech Connect

Oil-shale solid wastes are evaluated for use as soil stabilizers. A laboratory study consisted of the following tests on compacted samples of soil treated with water and spent oil shale: unconfined compressive strength, moisture-density relationships, wet-dry and freeze-thaw durability, and resilient modulus. Significant increases in strength, durability, and resilient modulus were obtained by treating a silty sand with combusted western oil shale. Moderate increases in durability and resilient modulus were obtained by treating a highly plastic clay with combusted western oil shale. Solid waste from eastern oil shale appears to be feasible for soil stabilization only if limestone is added during combustion. Testing methods, results, and recommendations for mix design of spent shale-stabilized pavement subgrades are presented and the mechanisms of spent-shale cementation are discussed.

Turner, J.P. (Univ. of Wyoming, Laramie, WY (United States). Dept. of Civil and Archeological Engineering)

1994-04-01T23:59:59.000Z

315

Gamma monitor for assay of radioactive solid-waste shipments  

SciTech Connect

A gamma waste monitor has been developed and evaluated at the Savannah River Plant (SRP). The purpose of the monitor is to improve estimates of the radionuclides in solid wastes arriving at the plant's burial ground. This monitor, a computer-based spectrometer, quantitatively measures many radionuclides in SRP waste, including waste in heavily shielded shipping casks. Radionuclides emitting gamma rays of sufficient energy to penetrate the shipping container walls can be measured directly. Other radionuclides that are beta emitters or which emit gamma photons too weak to penetrate the walls of the waste containers can often be estimated by their association with measurable gamma photons. Development of the monitor was initiated to find a more accurate method of estimating the quantities of radioactive materials accumulated in the burial ground and to ensure compliance with burial limits imposed by SRP technical standards. Another benefit from the monitor is that it provides specific radionuclide data which are essential to environmental impact evaluations and decommissioning planning. The gamma waste monitor is described. (WHK)

Crawford, J H

1982-06-01T23:59:59.000Z

316

Supplemental design requirements document solid waste operations complex  

SciTech Connect

This document provides additional and supplemental information to the WHC-SD-W112-FDC-001, WHC-SD-W113-FDC-001, and WHC-SD-W100-FDC-001. It provides additional requirements for the design and summarizes Westinghouse Hanford Company key design guidance and establishes the technical baseline agreements to be used for definitive design common to the Solid Waste Operations Complex (SWOC) Facilities (Project W-112, Project W-113, and WRAP 2A).

Ocampo, V.P.; Boothe, G.F.; Broz, D.R.; Eaton, H.E.; Greager, T.M.; Huckfeldt, R.A.; Kooiker, S.L.; Lamberd, D.L.; Lang, L.L.; Myers, J.B. [and others

1994-11-01T23:59:59.000Z

317

In-line ultrasonic monitoring of waste slurry suspended solids  

SciTech Connect

During the transport of tank waste, it is very important to quantitatively measure the percent solids concentration (PSC) of the waste, which indicates the flow conditions and the extent of solids settling. At Argonne National Laboratory, an in-line, real-time, a nonintrusive ultrasonic monitoring system has been developed to measure the PSC and flow density of tank waste by measuring sound velocity and attenuation in the flow. This system consists of a pair of longitudinal transducers bonded to waveguides on the opposite sides of the pipe and operating at IMHz simultaneously in pulse-and-echo and pitch-and-catch modes. The PSC measurement is provided by attenuation, while the density measurement is calculated by impedance and sound velocity. A thermocouple is attached to one of the waveguides for automatic temperature correction of the measurements. This system was one of four evaluated for in-line measurement of slurry at Oak Ridge National Laboratory in 1998. The results indicate that the measurements are in good agreement with a Coriolis meter and that the system can be used to monitor PSC up to 40 wt.%. However, the system is greatly affected by entrained air bubbles within the solid flow during Puisair mixing. A different mixing mechanism will solve this problem.

Chien, H.-T.; Sheen, S.-H.; Raptis, A. C.

2000-05-25T23:59:59.000Z

318

Revaluing waste in New York City : planning for small-scale compost  

E-Print Network (OSTI)

One-third of the municipal solid waste stream is organic material that, when processed in landfills, produces methane, a highly potent greenhouse gas. Composting is a proven strategy for organic waste management, which ...

Neilson, Sarah (Sarah Jane)

2009-01-01T23:59:59.000Z

319

Fuel Gas Production from Organic Wastes by Low Capital Cost Batch Digestion  

Science Journals Connector (OSTI)

The technical background is reviewed on energy recovery from biomass--i.e., all organic wastes, especially municipal solid wastes, but also including agricultural residues and crops grown specifically for ener...

Donald L. Wise; Alfred P. Leuschner…

1986-01-01T23:59:59.000Z

320

Processing of solid mixed waste containing radioactive and hazardous materials  

DOE Patents (OSTI)

Apparatus for the continuous heating and melting of a solid mixed waste bearing radioactive and hazardous materials to form separate metallic, slag and gaseous phases for producing compact forms of the waste material to facilitate disposal includes a copper split water-cooled (cold) crucible as a reaction vessel for receiving the waste material. The waste material is heated by means of the combination of a plasma torch directed into the open upper portion of the cold crucible and an electromagnetic flux produced by induction coils disposed about the crucible which is transparent to electromagnetic fields. A metallic phase of the waste material is formed in a lower portion of the crucible and is removed in the form of a compact ingot suitable for recycling and further processing. A glass-like, non-metallic slag phase containing radioactive elements is also formed in the crucible and flows out of the open upper portion of the crucible into a slag ingot mold for disposal. The decomposition products of the organic and toxic materials are incinerated and converted to environmentally safe gases in the melter. 6 figs.

Gotovchikov, V.T.; Ivanov, A.V.; Filippov, E.A.

1998-05-12T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Solid Waste Program Fiscal Year 1996 Multi-Year Program Plan WBS 1.2.1, Revision 1  

SciTech Connect

This document contains the Fiscal Year 1996 Multi-Year Program Plan for the Solid Waste Program at the Hanford Reservation in Richland, Washington. The Solid Waste Program treats, stores, and disposes of a wide variety of solid wastes consisting of radioactive, nonradioactive and hazardous material types. Solid waste types are typically classified as transuranic waste, low-level radioactive waste, low-level mixed waste, and non-radioactive hazardous waste. This report describes the mission, goals and program strategies for the Solid Waste Program for fiscal year 1996 and beyond.

NONE

1995-09-01T23:59:59.000Z

322

Field study of disposed solid wastes from advanced coal processes  

SciTech Connect

Radian Corporation and the North Dakota Energy and Environmental Research Center (EERC) are funded to develop information to be used by private industry and government agencies for managing solid wastes produced by advanced coal combustion processes. This information will be developed by conducting several field studies on disposed wastes from these processes. Data will be collected to characterize these wastes and their interactions with the environments in which they are disposed. Three sites were selected for the field studies: Colorado Ute's fluidized bed combustion (FBC) unit in Nucla, Colorado; Ohio Edison's limestone injection multistage burner (LIMB) retrofit in Lorain, Ohio; and Freeman United's mine site in central Illinois with wastes supplied by the nearby Midwest Grain FBC unit. During the past year, field monitoring and sampling of the four landfill test cases constructed in 1989 and 1991 has continued. Option 1 of the contract was approved last year to add financing for the fifth test case at the Freeman United site. The construction of the Test Case 5 cells is scheduled to begin in November, 1992. Work during this past year has focused on obtaining data on the physical and chemical properties of the landfilled wastes, and on developing a conceptual framework for interpreting this information. Results to date indicate that hydration reactions within the landfilled wastes have had a major impact on the physical and chemical properties of the materials but these reactions largely ceased after the first year, and physical properties have changed little since then. Conditions in Colorado remained dry and no porewater samples were collected. In Ohio, hydration reactions and increases in the moisture content of the waste tied up much of the water initially infiltrating the test cells.

Not Available

1992-01-01T23:59:59.000Z

323

PRODUCTION OF NEW BIOMASS/WASTE-CONTAINING SOLID FUELS  

SciTech Connect

CQ Inc. and its team members (ALSTOM Power Inc., Bliss Industries, McFadden Machine Company, and industry advisors from coal-burning utilities, equipment manufacturers, and the pellet fuels industry) addressed the objectives of the Department of Energy and industry to produce economical, new solid fuels from coal, biomass, and waste materials that reduce emissions from coal-fired boilers. This project builds on the team's commercial experience in composite fuels for energy production. The electric utility industry is interested in the use of biomass and wastes as fuel to reduce both emissions and fuel costs. In addition to these benefits, utilities also recognize the business advantage of consuming the waste byproducts of customers both to retain customers and to improve the public image of the industry. Unfortunately, biomass and waste byproducts can be troublesome fuels because of low bulk density, high moisture content, variable composition, handling and feeding problems, and inadequate information about combustion and emissions characteristics. Current methods of co-firing biomass and wastes either use a separate fuel receiving, storage, and boiler feed system, or mass burn the biomass by simply mixing it with coal on the storage pile. For biomass or biomass-containing composite fuels to be extensively used in the U.S., especially in the steam market, a lower cost method of producing these fuels must be developed that includes both moisture reduction and pelletization or agglomeration for necessary fuel density and ease of handling. Further, this method of fuel production must be applicable to a variety of combinations of biomass, wastes, and coal; economically competitive with current fuels; and provide environmental benefits compared with coal. Notable accomplishments from the work performed in Phase I of this project include the development of three standard fuel formulations from mixtures of coal fines, biomass, and waste materials that can be used in existing boilers, evaluation of these composite fuels to determine their applicability to the major combustor types, development of preliminary designs and economic projections for commercial facilities producing up to 200,000 tons per year of biomass/waste-containing fuels, and the development of dewatering technologies to reduce the moisture content of high-moisture biomass and waste materials during the pelletization process.

David J. Akers; Glenn A. Shirey; Zalman Zitron; Charles Q. Maney

2001-04-20T23:59:59.000Z

324

Cleanup Verification Package for the 118-C-1, 105-C Solid Waste Burial Ground  

SciTech Connect

This cleanup verification package documents completion of remedial action for the 118-C-1, 105-C Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-C Reactor and received process tubes, aluminum fuel spacers, control rods, reactor hardware, spent nuclear fuel and soft wastes.

M. J. Appel and J. M. Capron

2007-07-25T23:59:59.000Z

325

WIPP Facility Work Plan for Solid Waste Management Units  

SciTech Connect

This 2001 Facility Work Plan (FWP) has been prepared as required by Module VII, Section VII.M.1 of the Waste Isolation Pilot Plant (WIPP) Hazardous Waste Facility Permit, NM4890139088-TSDF (the Permit); (NMED, 1999a), and incorporates comments from the New Mexico Environment Department (NMED) received on December 6, 2000 (NMED, 2000a). This February 2001 FWP describes the programmatic facility-wide approach to future investigations at Solid Waste Management Units (SWMUs) and Areas of Concern (AOCs) specified in the Permit. The permittees are evaluating data from previous investigations of the SWMUs and AOCs against the newest guidance proposed by the NMED. Based on these data, the permittees expect that no further sampling will be required and that a request for No Further Action (NFA) at the SWMUs and AOCs will be submitted to the NMED. This FWP addresses the current Permit requirements. It uses the results of previous investigations performed at WIPP and expands the investigations as required by the Permit. As an alternative to the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) specified in Module VII of the Permit, current NMED guidance identifies an Accelerated Corrective Action Approach (ACAA) that may be used for any SWMU or AOC (NMED, 1998). This accelerated approach is used to replace the standard RFI Work Plan and Report sequence with a more flexible decision-making approach. The ACAA process allows a Facility to exit the schedule of compliance contained in the Facility’s Hazardous and Solid Waste Amendments (HSWA) permit module and proceed on an accelerated time frame. Thus, the ACAA process can be entered either before or after an RFI Work Plan. According to the NMED's guidance, a facility can prepare an RFI Work Plan or Sampling and Analysis Plan (SAP) for any SWMU or AOC (NMED, 1998). Based on this guidance, a SAP constitutes an acceptable alternative to the RFI Work Plan specified in the Permit.

Washington TRU Solutions LLC

2001-02-25T23:59:59.000Z

326

An overview of the sustainability of solid waste management at military installations  

E-Print Network (OSTI)

Arc Gasification. Sustainability of Solid Waste Management.and gasification technologies for energy efficient and environmentally sound MSW disposal." Wastewaste to energy (Provence 2008). Plasma Arc Gasification

Borglin, S.

2010-01-01T23:59:59.000Z

327

DOE/LX/07-0175&D1 Secondary Document DMSA OS-10 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-10 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 221 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

328

DOE/LX/07-0170&D1 Secondary Document DMSA OS-02 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-02 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 213 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

329

DOE/LX/07-0172&D1 Secondary Document DMSA OS-05 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-05 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 216 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

330

DOE/LX/07-0177&D1 Secondary Document DMSA OS-12 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-12 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 223 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

331

DOE/LX/07-0300&D1 Secondary Document DMSA OS-09 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-09 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 220 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 70202, 030105,...

332

DOE/LX/07-0063&D1 Secondary Document DMSA-333-11 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA-333-11 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 266 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 031509 REGULATORY...

333

DOE/LX/07-0178&D1 Secondary Document DMSA OS-13 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-13 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 224 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

334

DOE/LX/07-0302&D1 Secondary Document DMSA OS-15 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-15 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 226 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 011511 REGULATORY...

335

DOE/LX/07-0079&D1 Secondary Document DMSA OS-07 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-07 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 218 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 032404; 030105;...

336

DOE/LX/07-0061&D1 Secondary Document DMSA-333-19 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA-333-19 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 275 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 112502; 031509...

337

DOE/LX/07-0062&D1 Secondary Document DMSA-331-24 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA-331-24 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 255 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 031509 REGULATORY...

338

DOE/LX/07-0299&D1 Secondary Document DMSA OS-06 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-06 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 217 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 100703, 011511...

339

DOE/LX/07-0095 Secondary Document DMSA C-337-44 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-44 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 347 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 33106; 031509...

340

DOE/LX/07-0176&D1 Secondary Document DMSA OS-11 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-11 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 222 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 070202, 030105,...

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

DOE/LX/07-0301&D1 Secondary Document DMSA OS-14 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-14 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 225 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 011511...

342

DOE/LX/07-0298&D1 Secondary Document DMSA OS-04 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-04 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 215 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 011511 REGULATORY...

343

C-340 ST-90 Boxes Solid Waste Management Unit (SWMU) Assessment...  

NLE Websites -- All DOE Office Websites (Extended Search)

40 ST-90 Boxes Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 568 DATE OF ORIGINAL SAR: 112210 DATE OF SAR REVISIONS: NA REGULATORY STATUS: SWMU LOCATION:...

344

DOE/LX/07-0183&D1 Secondary Document DMSA OS-18 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-18 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 229 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 52803, 031509...

345

DOE/LX/07-0181&D1 Secondary Document DMSA OS-16 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-16 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 227 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 022704, 030205,...

346

DOE/LX/07-0182&D1 Secondary Document DMSA OS-17 Solid Waste Management...  

NLE Websites -- All DOE Office Websites (Extended Search)

Secondary Document DMSA OS-17 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 228 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

347

DOE/LX/07-0295 Secondary Document Rubble Area KY-19 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document Rubble Area KY-19 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 565 DATE OF ORIGINAL SAR: 091309 DATE OF SAR REVISIONS: NA REGULATORY STATUS:...

348

PPPO-02-225-07 Revised Solid Waste Management Unit Assessment...  

NLE Websites -- All DOE Office Websites (Extended Search)

Nitrogen Generating Facilities Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 483 DATE OF ORIGINAL SAR: 061501 DATE OF SAR REVISION: 061807 REGULATORY...

349

PPPO-02-340-07 Revised Solid Waste Management Unit Assessment...  

NLE Websites -- All DOE Office Websites (Extended Search)

Yard and C-748-B Burial Area Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 4 DATE OF ORIGINAL SAR: 8241987 DATE OF SAR REVISION: 06182007 REGULATORY...

350

Use of thermal analysis techniques (TG-DSC) for the characterization of diverse organic municipal waste streams to predict biological stability prior to land application  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Thermal analysis was used to assess stability and composition of organic matter in three diverse municipal waste streams. Black-Right-Pointing-Pointer Results were compared with C mineralization during 90-day incubation, FTIR and {sup 13}C NMR. Black-Right-Pointing-Pointer Thermal analysis reflected the differences between the organic wastes before and after the incubation. Black-Right-Pointing-Pointer The calculated energy density showed a strong correlation with cumulative respiration. Black-Right-Pointing-Pointer Conventional and thermal methods provide complimentary means of characterizing organic wastes. - Abstract: The use of organic municipal wastes as soil amendments is an increasing practice that can divert significant amounts of waste from landfill, and provides a potential source of nutrients and organic matter to ameliorate degraded soils. Due to the high heterogeneity of organic municipal waste streams, it is difficult to rapidly and cost-effectively establish their suitability as soil amendments using a single method. Thermal analysis has been proposed as an evolving technique to assess the stability and composition of the organic matter present in these wastes. In this study, three different organic municipal waste streams (i.e., a municipal waste compost (MC), a composted sewage sludge (CS) and a thermally dried sewage sludge (TS)) were characterized using conventional and thermal methods. The conventional methods used to test organic matter stability included laboratory incubation with measurement of respired C, and spectroscopic methods to characterize chemical composition. Carbon mineralization was measured during a 90-day incubation, and samples before and after incubation were analyzed by chemical (elemental analysis) and spectroscopic (infrared and nuclear magnetic resonance) methods. Results were compared with those obtained by thermogravimetry (TG) and differential scanning calorimetry (DSC) techniques. Total amounts of CO{sub 2} respired indicated that the organic matter in the TS was the least stable, while that in the CS was the most stable. This was confirmed by changes detected with the spectroscopic methods in the composition of the organic wastes due to C mineralization. Differences were especially pronounced for TS, which showed a remarkable loss of aliphatic and proteinaceous compounds during the incubation process. TG, and especially DSC analysis, clearly reflected these differences between the three organic wastes before and after the incubation. Furthermore, the calculated energy density, which represents the energy available per unit of organic matter, showed a strong correlation with cumulative respiration. Results obtained support the hypothesis of a potential link between the thermal and biological stability of the studied organic materials, and consequently the ability of thermal analysis to characterize the maturity of municipal organic wastes and composts.

Fernandez, Jose M., E-mail: joseman@sas.upenn.edu [Department of Earth and Environmental Science, University of Pennsylvania, Philadelphia, PA 19104-6316 (United States); Plaza, Cesar; Polo, Alfredo [Instituto de Ciencias Agrarias, Consejo Superior de Investigaciones Cientificas, Serrano 115 dpdo., 28006 Madrid (Spain); Plante, Alain F. [Department of Earth and Environmental Science, University of Pennsylvania, Philadelphia, PA 19104-6316 (United States)

2012-01-15T23:59:59.000Z

351

Solid Waste Processing Center Primary Opening Cells Systems, Equipment and Tools  

SciTech Connect

This document addresses the remote systems and design integration aspects of the development of the Solid Waste Processing Center (SWPC), a facility to remotely open, sort, size reduce, and repackage mixed low-level waste (MLLW) and transuranic (TRU)/TRU mixed waste that is either contact-handled (CH) waste in large containers or remote-handled (RH) waste in various-sized packages.

Bailey, Sharon A.; Baker, Carl P.; Mullen, O Dennis; Valdez, Patrick LJ

2006-04-17T23:59:59.000Z

352

Potential for Materials and Energy RecoveryPotential for Materials and Energy Recovery the Municipal Solid Wastes (the Municipal Solid Wastes (MSWMSW) of Beograd) of Beograd  

E-Print Network (OSTI)

Potential for Materials and Energy RecoveryPotential for Materials and Energy Recovery fromfrom;26.2World total 1.30.255.2Developing world 0.380.550.7 EU, Japan, Canada, Australia 0.331.10.3U.S.A. Tons MSW generated, billions Tons MSW per capita Population, billion Global generation of MSW Estimated SCG

Columbia University

353

Energy recovery from solid waste fuels using advanced gasification technology  

SciTech Connect

Since the mid-1980s, TPS Termiska Processer AB has been working on the development of an atmospheric-pressure gasification process. A major aim at the start of this work was the generation of fuel gas from indigenous fuels to Sweden (i.e. biomass). As the economic climate changed and awareness of the damage to the environment caused by the use of fossil fuels in power generation equipment increased, the aim of the development work at TPS was changed to applying the process to heat and power generation from feedstocks such as biomass and solid wastes. Compared with modern waste incineration with heat recovery, the gasification process will permit an increase in electricity output of up to 50%. The gasification process being developed is based on an atmospheric-pressure circulating fluidized bed gasifier coupled to a tar-cracking vessel. The gas produced from this process is then cooled and cleaned in conventional equipment. The energy-rich gas produced is clean enough to be fired in a gas boiler without requiring extensive flue gas cleaning, as is normally required in conventional waste incineration plants. Producing clean fuel gas in this manner, which facilitates the use of efficient gas-fired boilers, means that overall plant electrical efficiencies of close to 30% can be achieved. TPS has performed a considerable amount of pilot plant testing on waste fuels in their gasification/gas cleaning pilot plant in Sweden. Two gasifiers of TPS design have been in operation in Greve-in-Chianti, italy since 1992. This plant processes 200 tonnes of RDF (refuse-derived fuel) per day.

Morris, M.; Waldheim, L. [TPS Termiska Processer AB, Nykoeping (Sweden)] [TPS Termiska Processer AB, Nykoeping (Sweden)

1998-12-31T23:59:59.000Z

354

WIPP Facility Work Plan for Solid Waste Management Units  

SciTech Connect

This 2002 Facility Work Plan (FWP) has been prepared as required by Module VII, Permit Condition VII.U.3 of the Waste Isolation Pilot Plant (WIPP) Hazardous Waste Facility Permit, NM4890139088-TSDF (the Permit) (New Mexico Environment Department [NMED], 1999a), and incorporates comments from the NMED received on December 6, 2000 (NMED, 2000a). This February 2002 FWP describes the programmatic facility-wide approach to future investigations at Solid Waste Management Units (SWMU) and Areas of Concern (AOC) specified in the Permit. The Permittees are evaluating data from previous investigations of the SWMUs and AOCs against the most recent guidance proposed by the NMED. Based on these data, and completion of the August 2001 sampling requested by the NMED, the Permittees expect that no further sampling will be required and that a request for No Further Action (NFA) at the SWMUs and AOCs will be submitted to the NMED. This FWP addresses the current Permit requirements. It uses the results of previous investigations performed at WIPP and expands the investigations as required by the Permit. As an alternative to the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) specified in Module VII of the Permit, current NMED guidance identifies an Accelerated Corrective Action Approach (ACAA) that may be used for any SWMU or AOC (NMED, 1998). This accelerated approach is used to replace the standard RFI Work Plan and Report sequence with a more flexible decision-making approach. The ACAA process allows a facility to exit the schedule of compliance contained in the facility's Hazardous and Solid Waste Amendments (HSWA) permit module and proceed on an accelerated time frame. Thus, the ACAA processcan be entered either before or after an RFI Work Plan. According to the NMED's guidance, a facility can prepare an RFI Work Plan or Sampling and Analysis Plan (SAP) for any SWMU or AOC (NMED, 1998). Based on this guidance, a SAP constitutes an acceptable alternative to the RFI Work Plan specified in the Permit. The NMED accepted that the Permittees are using the ACAA in a letter dated April 20, 2000.

Washington TRU Solutions LLC

2002-02-14T23:59:59.000Z

355

WIPP Facility Work Plan for Solid Waste Management Units  

SciTech Connect

This Facility Work Plan (FWP) has been prepared as required by Module VII,Section VII.M.1 of the Waste Isolation Pilot Plant (WIPP) Hazardous Waste Permit, NM4890139088-TSDF (the Permit); (NMED, 1999a). This work plan describes the programmatic facility-wide approach to future investigations at Solid Waste Management Units (SWMUs) and Areas of Concern (AOCs) specified in the Permit. This FWP addresses the current Permit requirements. It uses the results of previous investigations performed at WIPP and expands the investigations as required by the Permit. As an alternative to the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) specified in Module VII of the Permit, current New Mexico Environment Department (NMED) guidance identifies an Accelerated Corrective Action Approach (ACAA) that may be used for any SWMU or AOC (NMED, 1998). This accelerated approach is used to replace the standard RFI Work Plan and Report sequence with a more flexible decision-making approach. The ACAA process allows a Facility to exit the schedule of compliance contained in the Facility’s Hazardous and Solid Waste Amendments (HSWA) permit module and proceed on an accelerated time frame. Thus, the ACAA process can be entered either before or after an RFI Work Plan. According to NMED’s guidance, a facility can prepare an RFI Work Plan or Sampling and Analysis Plan (SAP) for any SWMU or AOC (NMED, 1998). Based on this guidance, a SAP constitutes an acceptable alternative to the RFI Work Plan specified in the Permit. The scope of work for the RFI Work Plan or SAP is being developed by the Permittees. The final content of the RFI Work Plan or SAP will be coordinated with the NMED for submittal on May 24, 2000. Specific project-related planning information will be included in the RFI Work Plan or SAP. The SWMU program at WIPP began in 1994 under U.S. Environmental Protection Agency (EPA) regulatory authority. NMED subsequently received regulatory authority from EPA. A Phase I RFI was completed at WIPP as part of a Voluntary Release Assessment (VRA). The risk-based decision criteria recommended by EPA for the VRA were contained in a proposed Corrective Action rule for SWMUs (EPA, 1990). EPA Region VI has issued new risk-based screening criteria applicable to the WIPP SWMUs and AOCs.

Washington TRU Solutions LLC

2000-02-25T23:59:59.000Z

356

GRR/Section 18-ID-d - Solid Waste Management Facilities | Open Energy  

Open Energy Info (EERE)

8-ID-d - Solid Waste Management Facilities 8-ID-d - Solid Waste Management Facilities < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 18-ID-d - Solid Waste Management Facilities 18IDDSolidWasteManagementFacilities (2).pdf Click to View Fullscreen Contact Agencies Idaho Department of Environmental Quality Regulations & Policies IDAPA 58.01.06 Triggers None specified Click "Edit With Form" above to add content 18IDDSolidWasteManagementFacilities (2).pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative Idaho considers transfer stations, composting operations, incinerators and landfills solid waste management facilities. The state does not require a

357

EA-0767: Construction and Experiment of an Industrial Solid Waste Landfill  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

767: Construction and Experiment of an Industrial Solid Waste 767: Construction and Experiment of an Industrial Solid Waste Landfill at Portsmouth Gaseous Diffusion Plant, Piketon, Ohio EA-0767: Construction and Experiment of an Industrial Solid Waste Landfill at Portsmouth Gaseous Diffusion Plant, Piketon, Ohio SUMMARY This EA evaluates the environmental impacts of a proposal to construct and operate a solid waste landfill within the boundary at the U.S. Department of Energy's Portsmouth Gaseous Diffusion plant in Piketon, Ohio. PUBLIC COMMENT OPPORTUNITIES None available at this time. DOCUMENTS AVAILABLE FOR DOWNLOAD October 25, 1995 EA-0767: Finding of No Significant Impact Construction and Experiment of an Industrial Solid Waste Landfill at Portsmouth Gaseous Diffusion Plant October 25, 1995 EA-0767: Final Environmental Assessment

358

Evaluation of Technologies to Remove Suspended Solids from Waste Water  

SciTech Connect

The Effluent Treatment Facility (ETF) at the Savannah River Site utilizes pH adjustment, submicron filtration, Hg removal resin, activated carbon, reverse osmosis, cationic exchange, and evaporation to remove contaminants from radioactive waste water. After startup, the ETF had difficulty achieving design capacity. The primary problem was fouling of the ceramic microfilters. Typical filter flow rates were only 20 percent of design capacity.A research program was conducted to identify and evaluate technologies for improving suspended solids removal from radioactive wastewater at the Savannah River Site. Technolgies investigated were a ceramic microfilter, a tubular polymeric ultrafilter, two porous metal filters, a polymeric centrifugal ultrafilter, a deep bed filter, a backwashable cartridge filter, a fabric filter, and a centriguge.

Poirier, M.R.

1999-03-15T23:59:59.000Z

359

Production of New Biomass/Waste-Containing Solid Fuels  

SciTech Connect

CQ Inc. and its industry partners--PBS Coals, Inc. (Friedens, Pennsylvania), American Fiber Resources (Fairmont, West Virginia), Allegheny Energy Supply (Williamsport, Maryland), and the Heritage Research Group (Indianapolis, Indiana)--addressed the objectives of the Department of Energy and industry to produce economical, new solid fuels from coal, biomass, and waste materials that reduce emissions from coal-fired boilers. This project builds on the team's commercial experience in composite fuels for energy production. The electric utility industry is interested in the use of biomass and wastes as fuel to reduce both emissions and fuel costs. In addition to these benefits, utilities also recognize the business advantage of consuming the waste byproducts of customers both to retain customers and to improve the public image of the industry. Unfortunately, biomass and waste byproducts can be troublesome fuels because of low bulk density, high moisture content, variable composition, handling and feeding problems, and inadequate information about combustion and emissions characteristics. Current methods of co-firing biomass and wastes either use a separate fuel receiving, storage, and boiler feed system, or mass burn the biomass by simply mixing it with coal on the storage pile. For biomass or biomass-containing composite fuels to be extensively used in the U.S., especially in the steam market, a lower cost method of producing these fuels must be developed that is applicable to a variety of combinations of biomass, wastes, and coal; economically competitive with current fuels; and provides environmental benefits compared with coal. During Phase I of this project (January 1999 to July 2000), several biomass/waste materials were evaluated for potential use in a composite fuel. As a result of that work and the team's commercial experience in composite fuels for energy production, paper mill sludge and coal were selected for further evaluation and demonstration in Phase II. In Phase II (June 2001 to December 2004), the project team demonstrated the GranuFlow technology as part of a process to combine paper sludge and coal to produce a composite fuel with combustion and handling characteristics acceptable to existing boilers and fuel handling systems. Bench-scale studies were performed at DOE-NETL, followed by full-scale commercial demonstrations to produce the composite fuel in a 400-tph coal cleaning plant and combustion tests at a 90-MW power plant boiler to evaluate impacts on fuel handling, boiler operations and performance, and emissions. A circuit was successfully installed to re-pulp and inject paper sludge into the fine coal dewatering circuit of a commercial coal-cleaning plant to produce 5,000 tons of a ''composite'' fuel containing about 5% paper sludge. Subsequent combustion tests showed that boiler efficiency and stability were not compromised when the composite fuel was blended with the boiler's normal coal supply. Firing of the composite fuel blend did not have any significant impact on emissions as compared to the normal coal supply, and it did not cause any excursions beyond Title V regulatory limits; all emissions were well within regulatory limits. SO{sub 2} emissions decreased during the composite fuel blend tests as a result of its higher heat content and slightly lower sulfur content as compared to the normal coal supply. The composite fuel contained an extremely high proportion of fines because the parent coal (feedstock to the coal-cleaning plant) is a ''soft'' coal (HGI > 90) and contained a high proportion of fines. The composite fuel was produced and combustion-tested under record wet conditions for the local area. In spite of these conditions, full load was obtained by the boiler when firing the composite fuel blend, and testing was completed without any handling or combustion problems beyond those typically associated with wet coal. Fuel handling and pulverizer performance (mill capacity and outlet temperatures) could become greater concerns when firing composite fuels which contain higher percent

Glenn A. Shirey; David J. Akers

2005-09-23T23:59:59.000Z

360

FY 1996 solid waste integrated life-cycle forecast characteristics summary. Volumes 1 and 2  

SciTech Connect

For the past six years, a waste volume forecast has been collected annually from onsite and offsite generators that currently ship or are planning to ship solid waste to the Westinghouse Hanford Company`s Central Waste Complex (CWC). This document provides a description of the physical waste forms, hazardous waste constituents, and radionuclides of the waste expected to be shipped to the CWC from 1996 through the remaining life cycle of the Hanford Site (assumed to extend to 2070). In previous years, forecast data has been reported for a 30-year time period; however, the life-cycle approach was adopted this year to maintain consistency with FY 1996 Multi-Year Program Plans. This document is a companion report to two previous reports: the more detailed report on waste volumes, WHC-EP-0900, FY1996 Solid Waste Integrated Life-Cycle Forecast Volume Summary and the report on expected containers, WHC-EP-0903, FY1996 Solid Waste Integrated Life-Cycle Forecast Container Summary. All three documents are based on data gathered during the FY 1995 data call and verified as of January, 1996. These documents are intended to be used in conjunction with other solid waste planning documents as references for short and long-term planning of the WHC Solid Waste Disposal Division`s treatment, storage, and disposal activities over the next several decades. This document focuses on two main characteristics: the physical waste forms and hazardous waste constituents of low-level mixed waste (LLMW) and transuranic waste (both non-mixed and mixed) (TRU(M)). The major generators for each waste category and waste characteristic are also discussed. The characteristics of low-level waste (LLW) are described in Appendix A. In addition, information on radionuclides present in the waste is provided in Appendix B. The FY 1996 forecast data indicate that about 100,900 cubic meters of LLMW and TRU(M) waste is expected to be received at the CWC over the remaining life cycle of the site. Based on ranges provided by the waste generators, this baseline volume could fluctuate between a minimum of about 59,720 cubic meters and a maximum of about 152,170 cubic meters. The range is primarily due to uncertainties associated with the Tank Waste Remediation System (TWRS) program, including uncertainties regarding retrieval of long-length equipment, scheduling, and tank retrieval technologies.

Templeton, K.J.

1996-05-23T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Solid waste integrated forecast technical (SWIFT) report: FY1997 to FY 2070, Revision 1  

SciTech Connect

This web site provides an up-to-date report on the radioactive solid waste expected to be managed by Hanford's Waste Management (WM) Project from onsite and offsite generators. It includes: an overview of Hanford-wide solid waste to be managed by the WM Project; program-level and waste class-specific estimates; background information on waste sources; and comparisons with previous forecasts and with other national data sources. This web site does not include: liquid waste (current or future generation); waste to be managed by the Environmental Restoration (EM-40) contractor (i.e., waste that will be disposed of at the Environmental Restoration Disposal Facility (ERDF)); or waste that has been received by the WM Project to date (i.e., inventory waste). The focus of this web site is on low-level mixed waste (LLMW), and transuranic waste (both non-mixed and mixed) (TRU(M)). Some details on low-level waste and hazardous waste are also provided. Currently, this web site is reporting data th at was requested on 10/14/96 and submitted on 10/25/96. The data represent a life cycle forecast covering all reported activities from FY97 through the end of each program's life cycle. Therefore, these data represent revisions from the previous FY97.0 Data Version, due primarily to revised estimates from PNNL. There is some useful information about the structure of this report in the SWIFT Report Web Site Overview.

Valero, O.J.; Templeton, K.J.; Morgan, J.

1997-01-07T23:59:59.000Z

362

Supercritical/Solid Catalyst (SSC)  

ScienceCinema (OSTI)

INL's patented, continuous-flow Supercritical/Solid Catalyst (SSC) produces the highest ASTM-quality B-100 biodiesel from waste fats, oils, and greases at the site of waste generation. SSC delivers low-cost transportation fuel, avoids significant landfill costs for municipalities, and reduces potent methane and other emissions produced in landfills from these wastes. You can learn more about INL's energy research programs at http://www.facebook.com/idahonationallaboratory.

None

2013-05-28T23:59:59.000Z

363

Systems approaches to integrated solid waste management in developing countries  

Science Journals Connector (OSTI)

Solid waste management (SWM) has become an issue of increasing global concern as urban populations continue to rise and consumption patterns change. The health and environmental implications associated with SWM are mounting in urgency, particularly in the context of developing countries. While systems analyses largely targeting well-defined, engineered systems have been used to help SWM agencies in industrialized countries since the 1960s, collection and removal dominate the SWM sector in developing countries. This review contrasts the history and current paradigms of SWM practices and policies in industrialized countries with the current challenges and complexities faced in developing country SWM. In industrialized countries, public health, environment, resource scarcity, climate change, and public awareness and participation have acted as SWM drivers towards the current paradigm of integrated SWM. However, urbanization, inequality, and economic growth; cultural and socio-economic aspects; policy, governance, and institutional issues; and international influences have complicated SWM in developing countries. This has limited the applicability of approaches that were successful along the SWM development trajectories of industrialized countries. This review demonstrates the importance of founding new SWM approaches for developing country contexts in post-normal science and complex, adaptive systems thinking.

Rachael E. Marshall; Khosrow Farahbakhsh

2013-01-01T23:59:59.000Z

364

Composite analysis for solid waste storage area 6  

SciTech Connect

The composite analysis (CA) provides an estimate of the potential cumulative impacts to a hypothetical future member of the public from the Solid Waste Storage Area 6 (SWSA 6) disposal operations and all of the other sources of radioactive material in the ground on the ORR that may interact with contamination originating in SWSA 6.The projected annual dose to hypothetical future member of the public from all contributing sources is compared to the primary dose limit of 100 mrem per year and a dose constraint of 30 mrem per year. Consistent with the CA guidance, dose estimates for the first 1000 years after disposal are emphasized for comparison with the primary dose limit and dose constraint.The current land use plan for the ORR is being revised, and may include a reduction in the land currently controlled by DOE on the ORR. The possibility of changes in the land use boundary is considered in the CA as part of the sensitivity and uncertainty analysis of the results, the interpretation of results, and the conclusions.

Lee, D.W.

1997-09-01T23:59:59.000Z

365

Methods of reducing emissions of nitrogen oxides at thermal power plants burning solid domestic waste  

Science Journals Connector (OSTI)

Essentially all the major methods of reducing the emissions of nitrogen oxides from flue gases employed in power generation have been tested on plants in Moscow which burn solid domestic waste for production of h...

A. N. Tugov; V. F. Moskvichev

2009-01-01T23:59:59.000Z

366

EA-1097: Solid waste Disposal- Nevada Test Site, Nye County, Nevada  

Energy.gov (U.S. Department of Energy (DOE))

This EA evaluates the environmental impacts of the proposal to continue the on-site disposal of solid waste at the Area 9 and Area 23 landfills at the U.S. Department of Energy Nevada Test Site...

367

After the flood : crisis, voice and innovation in Maputo's solid waste management sector  

E-Print Network (OSTI)

This thesis explores responses to the problem of solid waste management (SWM) in two neighborhoods of Maputo, Mozambique in the wake of catastrophic flooding in 2000. In these neighborhoods, small-scale service providers ...

Kruks-Wisner, Gabrielle (Gabrielle K.)

2006-01-01T23:59:59.000Z

368

DOE/LX/07-0125&D1 Secondary Document DMSA-337-24 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

shipping the drums to Envirocare in Utah for disposal. As source material within the meaning of the Atomic Energy Act, UF 4 is not a solid waste; however, during the processing...

369

DOE/LX/07-0127&D1 Secondary Document DMSA-337-28 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

shipping the drums to Envirocare in Utah for disposal. As source material within the meaning of the Atomic Energy Act, UF 4 is not a solid waste; however, during the processing...

370

DOE/LX/07-0126&D1 Secondary Document DMSA-337-26 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

shipping the drums to Envirocare in Utah for disposal. As source material within the meaning of the Atomic Energy Act, UF 4 is not a solid waste; however, during the processing...

371

DOE/LX/07-0124&D1 Secondary Document DMSA-337-22 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

shipping the drums to Envirocare in Utah for disposal. As source material within the meaning of the Atomic Energy Act, UF 4 is not a solid waste; however, during the processing...

372

Thermal treatment of historical radioactive solid and liquid waste into the CILVA incinerator  

SciTech Connect

Since the very beginning of the nuclear activities in Belgium, the incineration of radioactive waste was chosen as a suitable technique for achieving an optimal volume reduction of the produced waste quantities. Based on the 35 years experience gained by the operation of the old incinerator, a new industrial incineration plant started nuclear operation in May 1995, as a part of the Belgian Centralized Treatment/Conditioning Facility named CILVA. Up to the end of 2006, the CILVA incinerator has burnt 1660 tonne of solid waste and 419 tonne of liquid waste. This paper describes the type and allowable radioactivity of the waste, the incineration process, heat recovery and the air pollution control devices. Special attention is given to the treatment of several hundreds of tonne historical waste from former reprocessing activities such as alpha suspected solid waste, aqueous and organic liquid waste and spent ion exchange resins. The capacity, volume reduction, chemical and radiological emissions are also evaluated. BELGOPROCESS, a company set up in 1984 at Dessel (Belgium) where a number of nuclear facilities were already installed is specialized in the processing of radioactive waste. It is a subsidiary of ONDRAF/NIRAS, the Belgian Nuclear Waste Management Agency. According to its mission statement, the activities of BELGOPROCESS focus on three areas: treatment, conditioning and interim storage of radioactive waste; decommissioning of shut-down nuclear facilities and cleaning of contaminated buildings and land; operating of storage sites for conditioned radioactive waste. (authors)

Deckers, Jan; Mols, Ludo [Belgoprocess NV, Operations Department, Gravenstraat 73, B-2480 Dessel (Belgium)

2007-07-01T23:59:59.000Z

373

Boiler tube failures in municipal waste-to-energy plants: Case histories  

SciTech Connect

Waste-to-energy plants experienced boiler tube failures when the design changed from waste-heat boilers to radiant furnace waterwalls with superheat, adopted from coal-firing technology. The fireside attack by chlorine and sulfur compounds in the refuse combustion products caused many forced outages in early European plants with high steam temperatures and pressures. In spite of conservative steam conditions in the first US plants, some failures occurred. As steam temperatures increased in later US plants, corrosion problems multiplied. Over the years these problems have been alleviated by covering the waterwalls with either refractories or weld overlays of nickel-base alloys and using high nickel-chromium alloys for superheater tubes. Various changes in furnace design to provide uniform combustion and avoid reducing conditions in the waterwall zone and to lower the gas temperature in the superheater also have helped to minimize corrosion.

Krause, H.H.; Wright, I.G. [Battelle, Columbus, OH (United States)

1995-12-01T23:59:59.000Z

374

Stabilization of high and low solids Consolidated Incinerator Facility (CIF) waste with super cement  

SciTech Connect

This report details solidification activities using selected Mixed Waste Focus Area technologies with the High and Low Solid waste streams. Ceramicrete and Super Cement technologies were chosen as the best possible replacement solidification candidates for the waste streams generated by the SRS incinerator from a list of several suggested Mixed Waste Focus Area technologies. These technologies were tested, evaluated, and compared to the current Portland cement technology being employed. Recommendation of a technology for replacement depends on waste form performance, process flexibility, process complexity, and cost of equipment and/or raw materials.

Walker, B.W.

2000-01-11T23:59:59.000Z

375

Ground-water monitoring compliance plan for the Hanford Site Solid Waste Landfill  

SciTech Connect

Washington state regulations required that solid waste landfill facilities have ground-water monitoring programs in place by May 27, 1987. This document describes the well locations, installation, characterization studies and sampling and analysis plan to be followed in implementing the ground-water monitoring program at the Hanford Site Solid Waste Landfill (SWL). It is based on Washington Administrative Code WAC 173-304-490. 11 refs., 19 figs., 4 tabs.

Fruland, R.M.

1986-10-01T23:59:59.000Z

376

SORPTION OF URANIUM, PLUTONIUM AND NEPTUNIUM ONTO SOLIDS PRESENT IN HIGH CAUSTIC NUCLEAR WASTE STORAGE TANKS  

SciTech Connect

Solids such as granular activated carbon, hematite and sodium phosphates, if present as sludge components in nuclear waste storage tanks, have been found to be capable of precipitating/sorbing actinides like plutonium, neptunium and uranium from nuclear waste storage tank supernatant liqueur. Thus, the potential may exists for the accumulation of fissile materials in such nuclear waste storage tanks during lengthy nuclear waste storage and processing. To evaluate the nuclear criticality safety in a typical nuclear waste storage tank, a study was initiated to measure the affinity of granular activated carbon, hematite and anhydrous sodium phosphate to sorb plutonium, neptunium and uranium from alkaline salt solutions. Tests with simulated and actual nuclear waste solutions established the affinity of the solids for plutonium, neptunium and uranium upon contact of the solutions with each of the solids. The removal of plutonium and neptunium from the synthetic salt solution by nuclear waste storage tank solids may be due largely to the presence of the granular activated carbon and transition metal oxides in these storage tank solids or sludge. Granular activated carbon and hematite also showed measurable affinity for both plutonium and neptunium. Sodium phosphate, used here as a reference sorbent for uranium, as expected, exhibited high affinity for uranium and neptunium, but did not show any measurable affinity for plutonium.

Oji, L; Bill Wilmarth, B; David Hobbs, D

2008-05-30T23:59:59.000Z

377

Energy from waste via coal/waste co-firing  

SciTech Connect

The paper reviews the feasibility of waste-to-energy plants using the cocombustion of coal with refuse-derived fuels. The paper discusses the types of wastes available: municipal solid wastes, plastics, tires, biomass, and specialized industrial wastes, such as waste oils, post-consumer carpet, auto shredder residues, and petroleum coke. The five most common combustion systems used in co-firing are briefly described. They are the stoker boiler, suspension-fired boilers, cyclone furnaces, fluidized bed boilers, and cement kilns. The paper also discusses the economic incentives for generating electricity from waste.

Winslow, J.; Ekmann, J.; Smouse, S. [Dept. of Energy, Pittsburgh, PA (United States). Pittsburgh Energy Technology Center; Ramezan, M. [Burns and Roe Services Corp., Pittsburgh, PA (United States); Harding, S.

1996-12-31T23:59:59.000Z

378

Fire protection guide for solid waste metal drum storage  

SciTech Connect

This guide provides a method to assess potential fire development in drum storage facilities. The mechanism of fire propagation/spread through stored drum arrays is a complex process. It involves flame heat transfer, transient conduction,convection, and radiation between drums (stored in an array configuration). There are several phenomena which may occur when drums are exposed to fire. The most dramatic is violent lid failure which results in total lid removal. When a drum loses its lid due to fire exposure, some or all of the contents may be ejected from the drum, and both the ejected combustible material and the combustible contents remaining within the container will burn. The scope of this guide is limited to storage arrays of steel drums containing combustible (primarily Class A) and noncombustible contents. Class B combustibles may be included in small amounts as free liquid within the solid waste contents.Storage arrays, which are anticipated in this guide, include single or multi-tier palletized (steel or wood pallets) drums,high rack storage of drums, and stacked arrays of drums where plywood sheets are used between tiers. The purpose of this guide is to describe a simple methodology that estimates the consequences of a fire in drum storage arrays. The extent of fire development and the resulting heat release rates can be estimated. Release fractions applicable to this type of storage are not addressed, and the transport of contaminants away from the source is not addressed. However, such assessments require the amount of combustible material consumed and the surface area of this burning material. The methods included in this guide do provide this information.

Bucci, H.M.

1996-09-16T23:59:59.000Z

379

A new theory of the creation of biomethane from aluminium-containing inorganic wastes  

Science Journals Connector (OSTI)

Energy by-products from the co-combustion of municipal solid waste with coal or biomass are monitored only in terms of oxides; the amount of metallic aluminium is not determined. When these energy by-products are...

Petr Buryan; Tomas Hlincik

2014-10-01T23:59:59.000Z

380

The Potential of Cellulosic Ethanol Production from Municipal Solid Waste: A Technical and Economic Evaluation  

E-Print Network (OSTI)

key to unlocking low-cost cellulosic ethanol. 2(1):26-40.1995 19941216. Commercial ethanol production process.facility and commercial ethanol production process.

Shi, Jian; Ebrik, Mirvat; Yang, Bin; Wyman, Charles E.

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

The Potential of Cellulosic Ethanol Production from Municipal Solid Waste: A Technical and Economic Evaluation  

E-Print Network (OSTI)

e.g. corn stover, wheat straw), herbaceous energy crops (for Corn Stover. Golden, Colorado: National Renewable Energy

Shi, Jian; Ebrik, Mirvat; Yang, Bin; Wyman, Charles E.

2009-01-01T23:59:59.000Z

382

Performance of a municipal solid waste (MSW) incinerator predicted with a computational fluid dynamics (CFD) code  

SciTech Connect

The purpose of this paper is to investigate by the means of numerical simulation the performance of the MSW incinerator with of Vercelli (Italy). FLUENT, a finite-volumes commercial code for Fluid Dynamics has been used to predict the 3-D reacting flows (gaseous phase) within the incinerator geometry, in order to estimate if the three conditions settled by the Italian law (P.D. 915 / 82) are respected: (a) Flue gas temperature at the input of the secondary combustion chamber must exceed 950 C. (b) Oxygen concentration in the same section must exceed 6 %. (c) Residence time for the flue gas in the secondary combustion chamber must exceed 2 seconds. The model of the incinerator has been created using the software pre-processing facilities (wall, input, outlet and live cells), together with the set-up of boundary conditions. There are also imposed the combustion constants (stoichiometry, heat of combustion, air excess). The solving procedure transforms at the level of each live cell the partial derivative equations in algebraic equations, computing the velocities field, the temperatures, gases concentration, etc. These predicted values were compared with the design properties, and the conclusion was that the conditions (a), (b), (c), are respected in normal operation. The powerful graphic interface helps the user to visualize the magnitude of the computed parameters. These results may be successfully used for the design and operation improvements for MSW incinerators. This fact will substantially increase the efficiency, reduce pollutant emissions and optimize the plant overall performance.

Anglesio, P.; Negreanu, G.P.

1998-07-01T23:59:59.000Z

383

Clean energy from municipal solid waste. ERIP Technical progress report No. 2  

SciTech Connect

Progress for the period July 1995 -- October 1995 for the slurry carbonization plant is described. Topics addressed include analytical results of carbonization of RDF, regression analysis of reactor temperature versus heating value of RDF fuel, and progress on reducing chlorine content of the fuels.

Klosky, M.

1995-10-02T23:59:59.000Z

384

Clean energy from municipal solid waste. Technical progress report No. 4  

SciTech Connect

This report documents progress made for the time period of January to April, 1996 in developing and testing a slurry carbonization plant at the Energy and Environment Research Center (EERC) in North Dakota. Various combinations of paper and plastics were carbonized` Performance parameters were assessed and the resulting refuse derived fuel pellets were analyzed for chemical composition and caloric values. Difficulties with performance and reliability of the equipment are discussed.

Klosky, M.

1996-04-08T23:59:59.000Z

385

Clean energy from municipal solid waste. ERIP technical progress report No. 1.  

SciTech Connect

Just prior to this award and reporting period but as part of this program, EnerTech initiated preliminary pilot scale slurry carbonization experiments with Refuse Derived Fuel (RDF) and preliminary pilot scale combustion experiments with the carbonized RDF slurry fuel. For this award and the time period April 1995--July 1995, several modifications to the pilot plant facilities were completed to improve operational reliability, system performance, and characteristics of the carbonized slurry fuel, based upon the previous plant experiments.

Klosky, M.

1995-07-14T23:59:59.000Z

386

Development of a Segregated Municipal Solid Waste Gasification System for Electrical Power Generation  

E-Print Network (OSTI)

. The overall engine-generator efficiency at 7.5 kW electrical power load was lower at 19.81% for gasoline fueled engine compared to 35.27% for synthesis gas. The pressure swing adsorption (PSA) system increased the net heating value of the product gas...

Maglinao, Amado Latayan

2013-04-11T23:59:59.000Z

387

Behavior of PCDD/Fs during open burning of municipal solid waste in open dumping sites  

Science Journals Connector (OSTI)

Open dumping sites in Surabaya and Palembang, Indonesia, have been studied to investigate emissions of polychlorinated dibenzo-para...-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls...

Lawin Bastian; Junya Yano; Yasuhiro Hirai…

2013-04-01T23:59:59.000Z

388

Evaluation of serum dioxin congeners among residents near continuously burning municipal solid waste incinerators in Korea  

Science Journals Connector (OSTI)

The objective of this study was to evaluate the congeners of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in Korean serum samples as biological markers. Serum samples from 1...

Chan-Seok Moon; Yoon-Seok Chang…

2005-04-01T23:59:59.000Z

389

Design Case Summary: Production of Mixed Alcohols from Municipal Solid Waste via Gasification  

Energy.gov (U.S. Department of Energy (DOE))

The Bioenergy Technologies Office develops design cases to understand the current state of conversion technologies and to determine where improvements need to take place in the future. This design case establishes cost targets for converting MSW to ethanol and other mixed alcohols via gasification.

390

Potential for Absorption Cooling Generated from Municipal Solid Waste in Bangkok.  

E-Print Network (OSTI)

?? This master’s thesis has been performed in Bangkok, Thailand at the company Eco Design Consultant Co., Ltd. The aim is to investigate the possibilities… (more)

Hedberg, Erika

2010-01-01T23:59:59.000Z

391

EVALUATION OF POSSIBLE GASIFIER-ENGINE APPLICATIONS WITH MUNICIPAL SOLID WASTE (A CASE STUDY OF KAMPALA).  

E-Print Network (OSTI)

?? Gasification of biomass for electricity power generation has been a proven technology in a number of countries in the world. MSW consists of biomass,… (more)

BERNARD, KIVUMBI

2011-01-01T23:59:59.000Z

392

Geochemical Modeling of Weathering Reactions in Municipal Solid Waste Incinerator Bottom Ash  

Science Journals Connector (OSTI)

The stability constants for ettringite (log Ksp = ?56.7; ... Additionally, ettringite (Ca6Al2(SO4)3(OH)12·26H2O) was identified in samples QUE1 and 6WK. ... Abbreviations:? por, portlandite; gyp, gypsum; ett, ettringite; cal, calcite; Ala, am-Al(OH)3; Alc, gibbsite; Fe1, ferrihydrite; Fe2, ferrihydrite (GS5 with fixed EH); Fe3, ferrihydrite (6WK with fixed EH); Fe4, ferrihydrite (QUE1 with fixed EH); SiO2, am-SiO2; wai, wairakite; ill, illite (12YR); bru, brucite; sep, sepiolite. ...

Jeannet A. Meima; Rob N. J. Comans

1997-04-29T23:59:59.000Z

393

The Potential of Cellulosic Ethanol Production from Municipal Solid Waste: A Technical and Economic Evaluation  

E-Print Network (OSTI)

to fuel ethanol because it not only contains cellulose andCellulose conversion, % Co-Fermentation Glucose-ethanolamount of cellulose, can be used as fuel ethanol feedstocks

Shi, Jian; Ebrik, Mirvat; Yang, Bin; Wyman, Charles E.

2009-01-01T23:59:59.000Z

394

An overview of renewable energy utilization from municipal solid waste (MSW) incineration in Taiwan  

E-Print Network (OSTI)

summarized in the paper. Finally, we present the regulatory system including Air Pollution Control Act . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495 4. Air pollution control regulations on MSW-to-energy . . . . . . . . . . . . . . . . . . . . . . . . . . . 497 4.1. MSW incinerator air pollutants emission standards

Columbia University

395

Report of the Review of the Hanford Solid Waste Environmental Impact  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of the Review of the Hanford Solid Waste Environmental of the Review of the Hanford Solid Waste Environmental Impact Statement regarding Data Quality Control and Management Issues Report of the Review of the Hanford Solid Waste Environmental Impact Statement regarding Data Quality Control and Management Issues As part of the litigation involving receipt of offsite waste and the HSW EIS, the Court allowed the State of Washington a limited amount of discovery pertaining to iodine-129, technetium-99, and groundwater analyses. While compiling information to respond to the State discovery request, Battelle discovered three data quality issues within the data sets used for the cumulative groundwater impact analysis: As a result of these data quality issues, a team was commissioned to review the HSW EIS for additional data quality issues as well as any programmatic problems which

396

Operating limit study for the proposed solid waste landfill at Paducah Gaseous Diffusion Plant  

SciTech Connect

A proposed solid waste landfill at Paducah Gaseous Diffusion Plant (PGDP) would accept wastes generated during normal operations that are identified as non-radioactive. These wastes may include small amounts of radioactive material from incidental contamination during plant operations. A site-specific analysis of the new solid waste landfill is presented to determine a proposed operating limit that will allow for waste disposal operations to occur such that protection of public health and the environment from the presence of incidentally contaminated waste materials can be assured. Performance objectives for disposal were defined from existing regulatory guidance to establish reasonable dose limits for protection of public health and the environment. Waste concentration limits were determined consistent with these performance objectives for the protection of off-site individuals and inadvertent intruders who might be directly exposed to disposed wastes. Exposures of off-site individuals were estimated using a conservative, site-specific model of the groundwater transport of contamination from the wastes. Direct intrusion was analyzed using an agricultural homesteader scenario. The most limiting concentrations from direct intrusion or groundwater transport were used to establish the concentration limits for radionuclides likely to be present in PGDP wastes.

Lee, D.W.; Wang, J.C.; Kocher, D.C.

1995-06-01T23:59:59.000Z

397

Scalable, Efficient Solid Waste Burner System - Energy Innovation...  

NLE Websites -- All DOE Office Websites (Extended Search)

combustion experts at CSU, the device is superior to other systems and achieves improved gasification and combustion of biomass and waste through novel chassis design and process....

398

Westinghouse Cementation Facility of Solid Waste Treatment System - 13503  

SciTech Connect

During NPP operation, several waste streams are generated, caused by different technical and physical processes. Besides others, liquid waste represents one of the major types of waste. Depending on national regulation for storage and disposal of radioactive waste, solidification can be one specific requirement. To accommodate the global request for waste treatment systems Westinghouse developed several specific treatment processes for the different types of waste. In the period of 2006 to 2008 Westinghouse awarded several contracts for the design and delivery of waste treatment systems related to the latest CPR-1000 nuclear power plants. One of these contracts contains the delivery of four Cementation Facilities for waste treatment, s.c. 'Follow on Cementations' dedicated to three locations, HongYanHe, NingDe and YangJiang, of new CPR-1000 nuclear power stations in the People's Republic of China. Previously, Westinghouse delivered a similar cementation facility to the CPR-1000 plant LingAo II, in Daya Bay, PR China. This plant already passed the hot functioning tests successfully in June 2012 and is now ready and released for regular operation. The 'Follow on plants' are designed to package three 'typical' kind of radioactive waste: evaporator concentrates, spent resins and filter cartridges. The purpose of this paper is to provide an overview on the Westinghouse experience to design and execution of cementation facilities. (authors)

Jacobs, Torsten; Aign, Joerg [Westinghouse Electric Germany GmbH, Global Waste Management, Tarpenring 6, D- 22419 Hamburg (Germany)] [Westinghouse Electric Germany GmbH, Global Waste Management, Tarpenring 6, D- 22419 Hamburg (Germany)

2013-07-01T23:59:59.000Z

399

FY 1996 solid waste integrated life-cycle forecast container summary volume 1 and 2  

SciTech Connect

For the past six years, a waste volume forecast has been collected annually from onsite and offsite generators that currently ship or are planning to ship solid waste to the Westinghouse Hanford Company`s Central Waste Complex (CWC). This document provides a description of the containers expected to be used for these waste shipments from 1996 through the remaining life cycle of the Hanford Site. In previous years, forecast data have been reported for a 30-year time period; however, the life-cycle approach was adopted this year to maintain consistency with FY 1996 Multi-Year Program Plans. This document is a companion report to the more detailed report on waste volumes: WHC-EP0900, FY 1996 Solid Waste Integrated Life-Cycle Forecast Volume Summary. Both of these documents are based on data gathered during the FY 1995 data call and verified as of January, 1996. These documents are intended to be used in conjunction with other solid waste planning documents as references for short and long-term planning of the WHC Solid Waste Disposal Division`s treatment, storage, and disposal activities over the next several decades. This document focuses on the types of containers that will be used for packaging low-level mixed waste (LLMW) and transuranic waste (both non-mixed and mixed) (TRU(M)). The major waste generators for each waste category and container type are also discussed. Containers used for low-level waste (LLW) are described in Appendix A, since LLW requires minimal treatment and storage prior to onsite disposal in the LLW burial grounds. The FY 1996 forecast data indicate that about 100,900 cubic meters of LLMW and TRU(M) waste are expected to be received at the CWC over the remaining life cycle of the site. Based on ranges provided by the waste generators, this baseline volume could fluctuate between a minimum of about 59,720 cubic meters and a maximum of about 152,170 cubic meters.

Valero, O.J.

1996-04-23T23:59:59.000Z

400

DOE/LX/07-0324&D1 Secondary Document DMSA C-333-35 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-35 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 289 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

DOE/LX/07-0149&D1 Secondary Document DMSA C-337-08 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-08 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 315 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031909 REGULATORY...

402

DOE/LX/07-0315&D1 Secondary Document DMSA C-333-14 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

4 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 269 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110 REGULATORY STATUS: SWMU...

403

DOE/LX/07-0289&D1 Secondary Document DMSA C-335-05 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-335-05 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 301 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 122107; 061410...

404

DOE/LX/07-0264&D1 Secondary Document DMSA C-337-03 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-03 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 310 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 061410 REGULATORY...

405

DOE/LX/07-0276&D1 Secondary Document DMSA C-333-09 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-09 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 264 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 061410 REGULATORY...

406

DOE/LX/07-0281&D1 Secondary Document DMSA C-333-28 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-28 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 284 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 061410 REGULATORY...

407

DOE/LX/07-0313&D1 Secondary Document DMSA C-333-07 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-07 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 262 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

408

DOE/LX/07-0087&D1 Secondary Document DMSA C-333-41 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-41 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 294 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 033106; 031509...

409

DOE/LX/07-0090&D1 Secondary Document DMSA C-335-03 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-335-03 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 299 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 33106; 031509...

410

DOE/LX/07-0191&D1 Secondary Document DMSA C-331-14 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-14 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 248 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 072502, 031509...

411

DOE/LX/07-0309&D1 Secondary Document DMSA C-333-03 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-03 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 258 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

412

DOE/LX/07-0213&D1 Secondary Document DMSA C-337-06 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-06 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 313 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030109 REGULATORY...

413

DOE/LX/07-0045&D1 Secondary Document DMSA C-331-01 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-01 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 235 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 031509 REGULATORY...

414

DOE/LX/07-0314&D1 Secondary Document DMSA C-333-12 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-12 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 267 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

415

DOE/LX/07-0056&D1 Secondary Document DMSA C-331-15 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-15 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 249 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 121101; 7202; 3...

416

DOE/LX/07-0058&D1 Secondary Document DMSA C-331-19 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-19 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 251 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 32103; 031509...

417

DOE/LX/07-0084&D1 Secondary Document DMSA C-331-12 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-12 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 246 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 012403; 030904;...

418

DOE/LX/07-0315&D1 Secondary Document DMSA C-333-13 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

3 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 268 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 82102, 031509, 030110 REGULATORY STATUS:...

419

DOE/LX/07-0154&D1 Secondary Document DMSA C-337-17 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-17 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 324 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031909 REGULATORY...

420

DOE/LX/07-0322&D1 Secondary Document DMSA C-333-30 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-30 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 286 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030110 REGULATORY...

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

DOE/LX/07-0211&D1 Secondary Document DMSA C-337-02 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-02 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 309 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

422

DOE/LX/07-0280&D1 Secondary Document DMSA C-333-25 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-25 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 281 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 061410 REGULATORY...

423

DOE/LX/07-0088&D1 Secondary Document DMSA C-333-43 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-43 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 296 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 32103, 30904, 02...

424

DOE/LX/07-0236&D1 Secondary Document DMSA C-337-12 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-12 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 319 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030110 REGULATORY...

425

DOE/LX/07-0342&D1 Secondary Document DMSA C-333-34 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-34 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 288 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 061410...

426

DOE/LX/07-0153&D1 Secondary Document DMSA C-337-15 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-15 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 322 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031909 REGULATORY...

427

DOE/LX/07-0151&D1 Secondary Document DMSA C-337-10 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-10 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 317 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031909 REGULATORY...

428

DOE/LX/07-0274&D1 Secondary Document DMSA C-335-08 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-335-08 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 304 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 122107, 061410...

429

DOE/LX/07-0319&D1 Secondary Document DMSA C-333-24 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-24 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 280 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

430

DOE/LX/07-0326&D1 Secondary Document DMSA C-337-04 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-04 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 311 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030110 REGULATORY...

431

DOE/LX/07-0189&D1 Secondary Document DMSA C-310-03 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-310-03 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 232 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

432

DOE/LX/07-0308&D1 Secondary Document DMSA C-333-02 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-02 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 257 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

433

DOE/LX/07-0085&D1 Secondary Document DMSA C-331-16 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-16 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 250 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030303; 033106;...

434

DOE/LX/07-0080&D1 Secondary Document DMSA C-331-04 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-04 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 238 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

435

DOE/LX/07-0067&D1 Secondary Document DMSA C-333-40 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-40 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 293 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 031509 REGULATORY...

436

DOE/LX/07-0288&D1 Secondary Document DMSA C-310-02 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-310-02 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 231 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 011003; 122107;...

437

DOE/LX/07-0148&D1 Secondary Document DMSA C-337-07 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-07 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 314 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

438

DOE/LX/07-0209&D1 Secondary Document DMSA C-335-06 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-335-06 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 302 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

439

DOE/LX/07-0066&D1 Secondary Document DMSA C-333-39 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-39 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 292 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 031509 REGULATORY...

440

DOE/LX/07-0152&D1 Secondary Document DMSA C-337-14 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-14 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 321 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031909 REGULATORY...

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

DOE/LX/07-0044&D1 Secondary Document DMSA C-310-05 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-310-05 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 234 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 031509 REGULATORY...

442

DOE/LX/07-0065&D1 Secondary Document DMSA C-333-37 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-37 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 290 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

443

DOE/LX/07-0190&D1 Secondary Document DMSA C-331-11 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-11 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 245 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

444

DOE/LX/07-0048&D1 Secondary Document DMSA C-331-03 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-331-03 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 237 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 031509 REGULATORY...

445

DOE/LX/07-0311&D1 Secondary Document DMSA C-333-05 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-05 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 260 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 30110...

446

DOE/LX/07-0068&D1 Secondary Document DMSA C-335-01 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-335-01 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 297 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 031509 REGULATORY...

447

DOE/LX/07-0327&D1 Secondary Document DMSA C-337-13 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-13 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 320 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030110 REGULATORY...

448

DOE/LX/07-0310&D1 Secondary Document DMSA C-333-04 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-04 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 259 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

449

DOE/LX/07-0155&D1 Secondary Document DMSA C-337-18 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-18 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 325 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031909 REGULATORY...

450

DOE/LX/07-0216&D1 Secondary Document DMSA C-337-16 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-16 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 323 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

451

DOE/LX/07-0321&D1 Secondary Document DMSA C-333-29 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-29 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 285 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030110 REGULATORY...

452

DOE/LX/07-0320&D1 Secondary Document DMSA C-333-27 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-27 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 283 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

453

DOE/LX/07-0208&D1 Secondary Document DMSA C-335-02 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-335-02 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 298 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

454

DOE/LX/07-0150&D1 Secondary Document DMSA C-337-09 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-09 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 316 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031909 REGULATORY...

455

DOE/LX/07-0210&D1 Secondary Document DMSA C-337-01 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-01 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 308 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

456

DOE/LX/07-0312&D1 Secondary Document DMSA C-333-06 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-06 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 261 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509, 030110...

457

DOE/LX/07-0091&D1 Secondary Document DMSA C-335-12 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-335-12 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 307 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 11105; 031509...

458

DOE/LX/07-0214&D1 Secondary Document DMSA C-337-11 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-11 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 318 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030109 REGULATORY...

459

DOE/LX/07-0283&D1 Secondary Document DMSA C-337-20 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-20 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 327 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 061410 REGULATORY...

460

DOE/LX/07-0089&D1 Secondary Document DMSA C-333-01 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-333-01 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 256 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 033106; 031509...

Note: This page contains sample records for the topic "municipal solid waste" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

DOE/LX/07-0158&D1 Secondary Document DMSA C-337-32 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-32 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 335 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 52908, 031509...

462

DOE/LX/07-0164&D1 Secondary Document DMSA C-337-39 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-39 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 342 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 020205, 031509...

463

DOE/LX/07-0094&D1 Secondary Document DMSA C-337-43 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-43 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 346 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISION: 33106; 031509...

464

DOE/LX/07-0284&D1 Secondary Document DMSA C-337-36 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-36 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 339 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 061410 REGULATORY...

465

DOE/LX/07-0331&D1 Secondary Document DMSA C-409-02 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-409-02 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 355 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 083002, 122107,...

466

DOE/LX/07-0328&D1 Secondary Document DMSA C-337-19 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-19 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 326 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030110 REGULATORY...

467

DOE/LX/07-0167&D1 Secondary Document DMSA C-720-02 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-720-02 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 357 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

468

DOE/LX/07-0157&D1 Secondary Document DMSA C-337-30 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-30 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 333 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

469

DOE/LX/07-0238&D1 Secondary Document DMSA C-337-21 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-21 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 328 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 030110 REGULATORY...

470

DOE/LX/07-0285&D1 Secondary Document DMSA C-337-37 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-37 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 340 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 012403; 061410...

471

DOE/LX/07-0159&D1 Secondary Document DMSA C-337-33 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-33 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 336 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

472

DOE/LX/07-0242&D1 Secondary Document DMSA C-400-05 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-400-05 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 351 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 080502, 122002,...

473

DOE/LX/07-0218&D1 Secondary Document DMSA C-337-31 Solid Waste...  

NLE Websites -- All DOE Office Websites (Extended Search)

Document DMSA C-337-31 Solid Waste Management Unit (SWMU) Assessment Report SWMUAOC NUMBER: 334 DATE OF ORIGINAL SAR: 120100 DATE OF SAR REVISIONS: 031509 REGULATORY...

474

Solid Waste Operations Complex (SWOC) Facilities Sprinkler System Hydraulic Calculations  

SciTech Connect

The attached calculations demonstrate sprinkler system operational water requirements as determined by hydraulic analysis. Hydraulic calculations for the waste storage buildings of the Central Waste Complex (CWC), T Plant, and Waste Receiving and Packaging (WRAP) facility are based upon flow testing performed by Fire Protection Engineers from the Hanford Fire Marshal's office. The calculations received peer review and approval prior to release. The hydraulic analysis program HASS Computer Program' (under license number 1609051210) is used to perform all analyses contained in this document. Hydraulic calculations demonstrate sprinkler system operability based upon each individual system design and available water supply under the most restrictive conditions.

KERSTEN, J.K.

2003-07-11T23:59:59.000Z

475

Proceedings of NAWTEC16 16th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

require pre-processing of the MSW, combust the resulting syngas to generate steam, and produce a vitrified used globally for energy recovery from municipal solid wastes is combustion of "as received" MSW combustion of solid wastes. In China, there have been some mass-burn new plants and also over forty

Columbia University

476

Power estimation and reliability evaluation of municipal waste water and self-excited induction generator-based micro hydropower generation system  

Science Journals Connector (OSTI)

This paper presents power estimation and reliability evaluation of the micro hydro power generation system based on municipal waste water. Self-excited induction generator was used in the developed power plant, situated at IIT (BHU) campus, Varanasi, India. The hydro potential of the waste water flowing through sewage system of the Banaras Hindu University has been determined for annual flow duration and daily flow duration curves by ordering the recorded waste water from maximum to minimum flows. This paper estimates output power and determines reliability indices like: failure rate, repair rate, MTTF, MTTR and MTBF of the MWW-based developed generation plant. Design parameters of the SEIG with suitable values of the capacitor have been used and recommended for improvement of the power generation quality and reliability of the system.

Lokesh Varshney; R.K. Saket; Saeid Eslamian

2013-01-01T23:59:59.000Z

477

Solid low-level radioactive waste radiation stability studies  

E-Print Network (OSTI)

properties and condition; on the other, on the specific features of thermal and radiation influences on it (Spitsyn et al. 1983). For the average composition of the fission products going to wastes repositories, the mean energy of irradiation may vary from... to the container determines, in part, the life of the container. Cormsion studies of containers by solidified wastes has indicated no problem areas in limited measurements to date; however very long-term effects have not been evaluated. The useful life...

Williams, Arnold Andre?

1989-01-01T23:59:59.000Z

478

Daily Gazette, Schenectady NY Letters to the Editor for Thursday, July 10, 2008 Nothing to fear, and much to gain, from waste-to-energy  

E-Print Network (OSTI)

, and much to gain, from waste-to-energy Schenectady is one of those misguided cities that sends its municipal solid wastes to distant landfills, costing much money, wasting valuable energy and increasing global warming and pollution of our environment. Waste-to-energy (WTE) is safe. I advised the Israel

Columbia University

479

Application of different levels of simulation to solid waste management systems  

SciTech Connect

Simulation techniques can be effectively applied to solid waste management systems, as an aid to understanding and analyzing existing systems or as part of the planning and design of new systems. Analysis of these systems using simulations can proceed at various levels of detail, depending on particular needs of the analysis (i.e., the questions for which answers are sought). This paper discusses the major system dimension variables for simulation of solid waste management systems, and how they can be related to each other to plan or understand a solid waste management system. Examples of the simulations at different levels of detail are included. In addition, the selection of appropriate simulation tools is addressed.

Holter, G.M.; Shaver, S.R.; Armacost, L.L.; Ross, T.L.

1993-11-01T23:59:59.000Z

480

Experimental Methods to Estimate Accumulated Solids in Nuclear Waste Tanks - 13313  

SciTech Connect

The Department of Energy has a large number of nuclear waste tanks. It is important to know if fissionable materials can concentrate when waste is transferred from staging tanks prior to feeding waste treatment plants. Specifically, there is a concern that large, dense particles, e.g., plutonium containing, could accumulate in poorly mixed regions of a blend tank heel for tanks that employ mixing jet pumps. At the request of the DOE Hanford Tank Operations Contractor, Washington River Protection Solutions, the Engineering Development Laboratory of the Savannah River National Laboratory performed a scouting study in a 1/22-scale model of a waste tank to investigate this concern and to develop measurement techniques that could be applied in a more extensive study at a larger scale. Simulated waste tank solids and supernatant were charged to the test tank and rotating liquid jets were used to remove most of the solids. Then the volume and shape of the residual solids and the spatial concentration profiles for the surrogate for plutonium were measured. This paper discusses the overall test results, which indicated heavy solids only accumulate during the first few transfer cycles, along with the techniques and equipment designed and employed in the test. Those techniques include: - Magnetic particle separator to remove stainless steel solids, the plutonium surrogate from a flowing stream. - Magnetic wand used to manually remove stainless steel solids from samples and the tank heel. - Photographs were used to determine the volume and shape of the solids mounds by developing a composite of topographical areas. - Laser range finders to determine the volume and shape of the solids mounds. - Core sampler to determine the stainless steel solids distribution within the solids mounds. - Computer driven positioner that placed the laser range finders and the core sampler over solids mounds that accumulated on the bottom of a scaled staging tank in locations where jet velocities were low. These devices and techniques were very effective to estimate the movement, location, and concentrations of the solids representing plutonium and are expected to perform well at a larger scale. The operation of the techniques and their measurement accuracies will be discussed as well as the overall results of the accumulated solids test. (authors)

Duignan, Mark R.; Steeper, Timothy J.; Steimke, John L. [Savannah River Nuclear Solutions, Savannah River National Laboratory, Aiken, SC 29808 (United States)] [Savannah River Nuclear Solutions, Savannah River National Laboratory, Aiken, SC 29808 (United States)

2013-07-01T23:59:59.000Z