Powered by Deep Web Technologies
Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Characterization of Multicrystalline Silicon Modules with System Bias Voltage Applied in Damp Heat  

DOE Green Energy (OSTI)

As it is considered economically favorable to serially connect modules to build arrays with high system voltage, it is necessary to explore potential long-term degradation mechanisms the modules may incur under such electrical potential. We performed accelerated lifetime testing of multicrystalline silicon PV modules in 85 degrees C/ 85% relative humidity and 45 degrees C/ 30% relative humidity while placing the active layer in either positive or negative 600 V bias with respect to the grounded module frame. Negative bias applied to the active layer in some cases leads to more rapid and catastrophic module power degradation. This is associated with significant shunting of individual cells as indicated by electroluminescence, thermal imaging, and I-V curves. Mass spectroscopy results support ion migration as one of the causes. Electrolytic corrosion is seen occurring with the silicon nitride antireflective coating and silver gridlines, and there is ionic transport of metallization at the encapsulant interface observed with damp heat and applied bias. Leakage current and module degradation is found to be highly dependent upon the module construction, with factors such as encapsulant and front glass resistivity affecting performance. Measured leakage currents range from about the same seen in published reports of modules deployed in Florida (USA) and is accelerated to up to 100 times higher in the environmental chamber testing.

Hacke, P.; Kempe, M.; Terwilliger, K.; Glick, S.; Call, N.; Johnston, S.; Kurtz, S.

2011-07-01T23:59:59.000Z

2

Material and process screening as applied to a reinforced plastic parabolic trough concentrator module  

DOE Green Energy (OSTI)

Existing parabolic trough solar collectors are basically sheet metal designs utilizing aluminum or steel as the major structural materials. The relatively high labor content associated with these sheet metal designs has generated an interest in investigating the cost effectiveness of using reinforced plastics as a major structural material for trough solar collectors. This interest is bolstered by a growing desire on the part of industry to identify new material-process combinations which save weight, use less energy, and require less capital equipment and assembly costs. The use of reinforced plastics as the basic material for a line-focus parabolic trough concentrator module is studied. This module constitutes a basic building block with which longer trough rows can be built. The basic part analysis is described including the quantification of key material and part-function relationships. In addition candidate materials and processes are reviewed and, the costs associated with the most attractive combinations defined. Finally, the major conclusions and recommendations are summarized.

Hodge, R. (ed.)

1980-08-01T23:59:59.000Z

3

Applied Science  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Science Applied Science Correlation of predicted and measured iron oxidation states in mixed iron oxides H. D. Rosenfeld and W. L. Holstein Development of a quantitative measurement of a diesel spray core using synchrotron x-rays C.F. Powell, Y. Yue, S. Gupta, A. McPherson, R. Poola, and J. Wang Localized phase transformations by x-ray-induced heating R.A. Rosenberg, Q. Ma, W. Farrell, E.D. Crozier, G.J. Soerensen, R.A. Gordon, and D.-T. Jiang Resonant x-ray scattering at the Se edge in ferroelectric liquid crystal materials L. Matkin, H. Gleeson, R. Pindak, P. Mach, C. Huang, G. Srajer, and J. Pollmann Synchrotron-radiation-induced anisotropic wet etching of GaAs Q. Ma, D.C. Mancini, and R.A. Rosenberg Synchrotron-radiation-induced, selective-area deposition of gold on

4

PDSF Modules  

NLE Websites -- All DOE Office Websites (Extended Search)

Modules Modules Modules Modules Approach to Managing The Environment Modules is a system which you can use to specify what software you want to use. If you want to use a particular software package loading its module will take care of the details of modifying your environment as necessary. The advantage of the modules approach is that the you are not required to explicitly specify paths for different executable versions and try to keep their related man paths and environment variables coordinated. Instead you simply "load" and "unload" specific modules to control your environment. Getting Started with Modules If you're using the standard startup files on PDSF then you're already setup for using modules. If the "module" command is not available, please

5

Applying Innovation System Concept in Agricultural Research for  

Open Energy Info (EERE)

Applying Innovation System Concept in Agricultural Research for Applying Innovation System Concept in Agricultural Research for Development: A learning module Jump to: navigation, search Tool Summary Name: Applying Innovation System Concept in Agricultural Research for Development: A learning module Agency/Company /Organization: International Livestock Research Institute Sector: Land Focus Area: Agriculture Topics: Policies/deployment programs Resource Type: Training materials Website: mahider.ilri.org/bitstream/10568/167/1/Innovation_System_Agric_LM.pdf Applying Innovation System Concept in Agricultural Research for Development: A learning module Screenshot References: Applying Innovation System Concept in Agricultural Research for Development: A learning module[1] Preface "Sustained agricultural growth requires, among others, increased

6

Module Configuration  

SciTech Connect

A stand alone battery module including: (a) a mechanical configuration; (b) a thermal management configuration; (c) an electrical connection configuration; and (d) an electronics configuration. Such a module is fully interchangeable in a battery pack assembly, mechanically, from the thermal management point of view, and electrically. With the same hardware, the module can accommodate different cell sizes and, therefore, can easily have different capacities. The module structure is designed to accommodate the electronics monitoring, protection, and printed wiring assembly boards (PWAs), as well as to allow airflow through the module. A plurality of modules may easily be connected together to form a battery pack. The parts of the module are designed to facilitate their manufacture and assembly.

Oweis, Salah (Ellicott City, MD); D' Ussel, Louis (Bordeaux, FR); Chagnon, Guy (Cockeysville, MD); Zuhowski, Michael (Annapolis, MD); Sack, Tim (Cockeysville, MD); Laucournet, Gaullume (Paris, FR); Jackson, Edward J. (Taneytown, MD)

2002-06-04T23:59:59.000Z

7

CX-010574: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Applied Materials - Kerf-less Crystaline-Silicon Photovoltaic: Gas to Modules CX(s) Applied: B3.6 Date: 05162013 Location(s): California,...

8

Apparatus for encapsulating a photovoltaic module  

DOE Patents (OSTI)

The subject inventions concern various photovoltaic module designs to protect the module from horizontal and vertical impacts and degradation of solar cell efficiency caused by moisture. In one design, a plurality of panel supports that are positioned adjacent to the upper panel in a photovoltaic module absorb vertical forces exerted along an axis perpendicular to the upper panel. Other designs employ layers of glass and tempered glass, respectively, to protect the module from vertical impacts. A plurality of button-shaped channels is used around the edges of the photovoltaic module to absorb forces applied to the module along an axis parallel to the module and direct moisture away from the module that could otherwise penetrate the module and adversely affect the cells within the module. A spacer is employed between the upper and lower panels that has a coefficient of thermal expansion substantially equivalent to the coefficient of thermal expansion of at least one of the panels.

Albright, Scot P. (El Paso, TX); Dugan, Larry M. (Boulder, CO)

1995-10-24T23:59:59.000Z

9

Module Handbook Specialisation Photovoltaics  

E-Print Network (OSTI)

#12;Specialisation Photovoltaics, University of Northumbria Module 1/Photovoltaics: PHOTOVOLTAIC CELL AND MODULE TECHNOLOGY Module name: PHOTOVOLTAIC CELL AND MODULE TECHNOLOGY Section EUREC · Chemistry · Physics Target learning outcomes The module Photovoltaic Cell and Module Technology teaches

Habel, Annegret

10

Tandem resonator reflectance modulator  

DOE Patents (OSTI)

A wide band optical modulator is grown on a substrate as tandem Fabry-Perot resonators including three mirrors spaced by two cavities. The absorption of one cavity is changed relative to the absorption of the other cavity by an applied electric field, to cause a change in total reflected light, as light reflecting from the outer mirrors is in phase and light reflecting from the inner mirror is out of phase with light from the outer mirrors. 8 figs.

Fritz, I.J.; Wendt, J.R.

1994-09-06T23:59:59.000Z

11

Tandem resonator reflectance modulator  

DOE Patents (OSTI)

A wide band optical modulator is grown on a substrate as tandem Fabry-Perot resonators including three mirrors spaced by two cavities. The absorption of one cavity is changed relative to the absorption of the other cavity by an applied electric field, to cause a change in total reflected light, as light reflecting from the outer mirrors is in phase and light reflecting from the inner mirror is out of phase with light from the outer mirrors.

Fritz, Ian J. (Albuquerque, NM); Wendt, Joel R. (Albuquerque, NM)

1994-01-01T23:59:59.000Z

12

Applied Quantum Information Science  

Science Conference Proceedings (OSTI)

Applied Quantum Information Science. Summary: Theory is being developed and used to devise methods for preserving ...

2012-05-30T23:59:59.000Z

13

Thermionic modules  

DOE Patents (OSTI)

Modules of assembled microminiature thermionic converters (MTCs) having high energy-conversion efficiencies and variable operating temperatures manufactured using MEMS manufacturing techniques including chemical vapor deposition. The MTCs incorporate cathode to anode spacing of about 1 micron or less and use cathode and anode materials having work functions ranging from about 1 eV to about 3 eV. The MTCs also exhibit maximum efficiencies of just under 30%, and thousands of the devices and modules can be fabricated at modest costs.

King, Donald B. (Albuquerque, NM); Sadwick, Laurence P. (Salt Lake City, UT); Wernsman, Bernard R. (Clairton, PA)

2002-06-18T23:59:59.000Z

14

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Download CX-004008: Categorical Exclusion Determination Commercialization of Silicon Carbide Power Modules for High Performance Energy Applications CX(s) Applied: B3.6,...

15

CX-005464: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Joining Technology for the Improved Solar Cell Module Manufacturing CX(s) Applied: B3.6 Date: 03142011 Location(s): Lansdale,...

16

CX-005465: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Joining Technology for the Improved Solar Cell Module Manufacturing CX(s) Applied: B3.6 Date: 03142011 Location(s): West Chester,...

17

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CX-002718: Categorical Exclusion Determination Advanced Low Temperature Heat Recovery Absorption Chiller Research, Development, and Demonstration (RD&D) Module CX(s) Applied:...

18

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CX-002713: Categorical Exclusion Determination Advanced Low Temperature Heat Recovery Absorption Chiller Research, Development, and Demonstration (RD&D) Module CX(s) Applied:...

19

CX-005646: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination CX-005646: Categorical Exclusion Determination Quantum Dot Light Emitting Diode Module CX(s) Applied: A9, B3.6 Date: 04252011 Location(s): Pittsburgh,...

20

CX-003536: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CX-003536: Categorical Exclusion Determination High-Bandwidth Modulation of HydrogenSyngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08262010...

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

CX-003537: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CX-003537: Categorical Exclusion Determination High-Bandwidth Modulation of HydrogenSyngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08262010...

22

CX-002713: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Advanced Low Temperature Heat Recovery Absorption Chiller Research, Development, and Demonstration (RD&D) Module CX(s) Applied: A1, A9 Date:...

23

North Carolina | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Advanced Low Temperature Heat Recovery Absorption Chiller Research, Development, and Demonstration (RD&D) Module CX(s) Applied: A1, A9 Date:...

24

CX-002716: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Advanced Low Temperature Heat Recovery Absorption Chiller Research, Development, and Demonstration (RD&D) Module CX(s) Applied: A1, A9 Date:...

25

Categorical Exclusion Determinations: American Recovery and Reinvestme...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Transphorm, Inc. -High Performance Gallium Nitride High Electron Mobility Transistor Modules for Agile Power Electronics CX(s) Applied: B3.6 Date:...

26

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Transphorm, Inc. -High Performance Gallium Nitride High Electron Mobility Transistor Modules for Agile Power Electronics CX(s) Applied: B3.6 Date:...

27

SOUTHVIEWDR Center for Applied  

E-Print Network (OSTI)

/Geology Chemistry Biological Sciences Geology Lab Bookstore Reed Milledge Payne Memorial Hall SANFORD DR Center CAES Activity Center Visitors Center (Four Towers) Greenhouses Center for Applied Isotope Study

Hall, Daniel

28

Photovoltaic module and module arrays  

DOE Patents (OSTI)

A photovoltaic (PV) module including a PV device and a frame. The PV device has a PV laminate defining a perimeter and a major plane. The frame is assembled to and encases the laminate perimeter, and includes leading, trailing, and side frame members, and an arm that forms a support face opposite the laminate. The support face is adapted for placement against a horizontal installation surface, to support and orient the laminate in a non-parallel or tilted arrangement. Upon final assembly, the laminate and the frame combine to define a unitary structure. The frame can orient the laminate at an angle in the range of 3.degree.-7.degree. from horizontal, and can be entirely formed of a polymeric material. Optionally, the arm incorporates integral feature(s) that facilitate interconnection with corresponding features of a second, identically formed PV module.

Botkin, Jonathan (El Cerrito, CA); Graves, Simon (Berkeley, CA); Lenox, Carl J. S. (Oakland, CA); Culligan, Matthew (Berkeley, CA); Danning, Matt (Oakland, CA)

2012-07-17T23:59:59.000Z

29

HP MSR30/50 Routers with Encryption Accelerator Modules  

Science Conference Proceedings (OSTI)

... 1 The RS-232/485 interfaces is reserved and not supported at present. ... Officer shall clean the module of any grease, dirt, or oil before applying the ...

2013-10-21T23:59:59.000Z

30

Applied Energy Programs  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Energy Programs Applied Energy Programs Applied Energy Programs Los Alamos is using its world-class scientific capabilities to enhance national energy security by developing energy sources with limited environmental impact and by improving the efficiency and reliability of the energy infrastructure. CONTACT US Acting Program Director Melissa Fox (505) 663-5538 Email Applied Energy Program Office serves as the hub connecting the Laboratory's scientific and technical resources to DOE sponsors, DoD programs, and to industry. The Applied Energy Program Office manages Los Alamos National Laboratory programs funded by the Department of Energy's (DOE's) Offices of Energy Efficiency/Renewable Energy, Electricity Delivery and Energy Reliability, and Fossil Energy. With energy use increasing across the nation and the

31

Light modulating device  

DOE Patents (OSTI)

In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity are disclosed. 1 fig.

Rauh, R.D.; Goldner, R.B.

1989-12-26T23:59:59.000Z

32

Essays in applied microeconomics  

E-Print Network (OSTI)

This dissertation consists of three chapters on topics in applied microeconomics. In the first chapter. I investigate whether voters are more likely to support additional spending on local public services when they perceive ...

Aron-Dine, Aviva

2012-01-01T23:59:59.000Z

33

Solid State Marx Modulators for Emerging Applications  

Science Conference Proceedings (OSTI)

Emerging linear accelerator applications increasingly push the boundaries of RF system performance and economics. The power modulator is an integral part of RF systems whose characteristics play a key role in the determining parameters such as efficiency, footprint, cost, stability, and availability. Particularly within the past decade, solid-state switch based modulators have become the standard in high-performance, high power modulators. One topology, the Marx modulator, has characteristics which make it particularly attractive for several emerging applications. This paper is an overview of the Marx topology, some recent developments, and a case study of how this architecture can be applied to a few proposed linear accelerators.

Kemp, M.A.; /SLAC

2012-09-14T23:59:59.000Z

34

TOB Module Assembly  

NLE Websites -- All DOE Office Websites (Extended Search)

SiTracker Home Page Participating Institutions and Principal Contacts Useful Links Notes Images TOB Module Assembly and Testing Project TOB Integration Data Tracker Offline DQM LHC Fluence Calculator Total US Modules Tested Graph Total US Modules Tested Graph Total US Modules Tested Total US Modules Tested US Modules Tested Graph US Modules Tested Graph US Modules Tested US Modules Tested Rod Assembly TOB Modules on a Rod TOB Rod Insertion Installation of a TOB Rod Completed TOB Completed Tracker Outer Barrel TOB Module Assembly and Testing Project All 5208 modules of the CMS Tracker Outer Barrel were assembled and tested at two production sites in the US: the Fermi National Accelerator Laboratory and the University of California at Santa Barbara. The modules were delivered to CERN in the form of rods, with the last shipment taking

35

Applied Science/Techniques  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Science/Techniques Applied Science/Techniques Applied Science/Techniques Print The ALS is an excellent incubator of new scientific techniques and instrumentation. Many of the technical advances that make the ALS a world-class soft x-ray facility are developed at the ALS itself. The optical components in use at the ALS-mirrors and lenses optimized for x-ray wavelengths-require incredibly high-precision surfaces and patterns (often formed through extreme ultraviolet lithography at the ALS) and must undergo rigorous calibration and testing provided by beamlines and equipment from the ALS's Optical Metrology Lab and Berkeley Lab's Center for X-Ray Optics. New and/or continuously improved experimental techniques are also a crucial element of a thriving scientific facility. At the ALS, examples of such "technique" highlights include developments in lensless imaging, soft x-ray tomography, high-throughput protein analysis, and high-power coherent terahertz radiation.

36

Applied Mathematics | Argonne National Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Mathematics Applied Mathematics Our work in applied mathematics ranges from algorithm design, to development of software tools and technology, to advanced simulations in...

37

Applied Science/Techniques  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Science/Techniques Print Applied Science/Techniques Print The ALS is an excellent incubator of new scientific techniques and instrumentation. Many of the technical advances that make the ALS a world-class soft x-ray facility are developed at the ALS itself. The optical components in use at the ALS-mirrors and lenses optimized for x-ray wavelengths-require incredibly high-precision surfaces and patterns (often formed through extreme ultraviolet lithography at the ALS) and must undergo rigorous calibration and testing provided by beamlines and equipment from the ALS's Optical Metrology Lab and Berkeley Lab's Center for X-Ray Optics. New and/or continuously improved experimental techniques are also a crucial element of a thriving scientific facility. At the ALS, examples of such "technique" highlights include developments in lensless imaging, soft x-ray tomography, high-throughput protein analysis, and high-power coherent terahertz radiation.

38

Ballasted photovoltaic module and module arrays  

DOE Patents (OSTI)

A photovoltaic (PV) module assembly including a PV module and a ballast tray. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes an arm. The ballast tray is adapted for containing ballast and is removably associated with the PV module in a ballasting state where the tray is vertically under the PV laminate and vertically over the arm to impede overt displacement of the PV module. The PV module assembly can be installed to a flat commercial rooftop, with the PV module and the ballast tray both resting upon the rooftop. In some embodiments, the ballasting state includes corresponding surfaces of the arm and the tray being spaced from one another under normal (low or no wind) conditions, such that the frame is not continuously subjected to a weight of the tray.

Botkin, Jonathan (El Cerrito, CA); Graves, Simon (Berkeley, CA); Danning, Matt (Oakland, CA)

2011-11-29T23:59:59.000Z

39

NERSC Modules Software Environment  

NLE Websites -- All DOE Office Websites (Extended Search)

Environment » Modules Environment Environment » Modules Environment Modules Software Environment NERSC uses the module utility to manage nearly all software. There are two huge advantages of the module approach: NERSC can provide many different versions and/or installations of a single software package on a given machine, including a default version as well as several older and newer versions; and Users can easily switch to different versions or installations without having to explicitly specify different paths. With modules, the MANPATH and related environment variables are automatically managed. Users simply ``load'' and ``unload'' modules to control their environment. The module utility consists of two parts: the module command itself and the modulefiles on which it operates. Module Command

40

Process of making solar cell module  

DOE Patents (OSTI)

A process is presented for the manufacture of solar cell modules. A solution comprising a highly plasticized polyvinyl butyral is applied to a solar cell array. The coated array is dried and sandwiched between at last two sheets of polyvinyl butyral and at least two sheets of a rigid transparent member. The sandwich is laminated by the application of heat and pressure to cause fusion and bonding of the solar cell array with the rigid transparent members to produce a solar cell module.

Packer, M.; Coyle, P.J.

1981-03-09T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Applied antineutrino physics workshop.  

Science Conference Proceedings (OSTI)

This workshop is the fourth one of a series that includes the Neutrino Geophysics Conference at Honolulu, Hawaii, which I attended in 2005. This workshop was organized by the Astro-Particle and Cosmology laboratory in the recently opened Condoret building of the University of Paris. More information, including copies of the presentations, on the workshop is available on the website: www.apc.univ-paris7.fr/AAP2007/. The workshop aims at opening neutrino physics to various fields such that it can be applied in geosciences, nuclear industry (reactor and spent fuel monitoring) and non-proliferation. The workshop was attended by over 60 people from Europe, USA, Asia and Brazil. The meeting was also attended by representatives of the Comprehensive nuclear-Test Ban Treaty (CTBT) and the International Atomic Energy Agency (IAEA). The workshop also included a workshop dinner on board of a river boat sailing the Seine river.

Lund, James C.

2008-01-01T23:59:59.000Z

42

Amplitude modulation of wind turbine noise  

E-Print Network (OSTI)

Due to swish and thump amplitude modulation, the noise of wind turbines cause more annoyance than other environmental noise of the same average level. The wind shear accounts for the thump modulation (van den Berg effect). Making use of the wind speed measurements at the hub height, as well as at the top and the bottom of the rotor disc (Fig.1), the non-standard wind profile is applied. It causes variations in the A-weighted sound pressure level, LpA. The difference between the maximum and minimum of LpA characterizes thump modulation (Fig.2).

Makarewicz, Rufin

2013-01-01T23:59:59.000Z

43

Advanced silicon photonic modulators  

E-Print Network (OSTI)

Various electrical and optical schemes used in Mach-Zehnder (MZ) silicon plasma dispersion effect modulators are explored. A rib waveguide reverse biased silicon diode modulator is designed, tested and found to operate at ...

Sorace, Cheryl M

2010-01-01T23:59:59.000Z

44

Applied and Computational Mathematics Division  

Science Conference Proceedings (OSTI)

Applied and Computational Mathematics Division. Topic Areas. Mathematics; Scientific Computing; Visualization; Quantum Computing. ...

2013-05-09T23:59:59.000Z

45

Modulating lignin in plants  

DOE Patents (OSTI)

Materials and methods for modulating (e.g., increasing or decreasing) lignin content in plants are disclosed. For example, nucleic acids encoding lignin-modulating polypeptides are disclosed as well as methods for using such nucleic acids to generate transgenic plants having a modulated lignin content.

Apuya, Nestor; Bobzin, Steven Craig; Okamuro, Jack; Zhang, Ke

2013-01-29T23:59:59.000Z

46

Photovoltaic module electrical termination design requirement study  

DOE Green Energy (OSTI)

Motorola Inc., in conjunction with ITT Cannon, has conducted a study to develop information to facilitate the selection of existing, commercial, electrical termination hardware for photovoltaic modules and arrays. This volume of the report contains the executive summary. Module and array design parameters were investigated and recommendations were developed for use in surveying, evaluating, and comparing electrical termination hardware. Electrical termination selection criteria factors were developed and applied to nine generic termination types in each of the four application sectors: remote, residential, intermediate and industrial. Existing terminations best suited for photovoltaic modules and arrays were identified. Cost information was developed to identify cost drivers and/or requirements which might lead to cost reductions. The general conclusion is that there is no single generic termination that is best suited for photovoltaic application, but that the appropriate termination is strongly dependent upon the module construction and its support structure as well as the specific application sector.

Mosna, F.J. Jr.; Donlinger, J.

1980-07-01T23:59:59.000Z

47

Ultrasonic beamforming with Delta-Sigma modulators  

Science Conference Proceedings (OSTI)

Delta - Sigma (??) modulation allows delay resolution in ultrasound beamformers to be achieved by simple clock cycle delays applied to the undecimated bitstream, greatly reducing the complexity of the signal processing and the number of bits ... Keywords: beamformer, delay, delta-sigma, ultrasound

Ioan Lie; Mihail Eugen Tanase; Dan Lascu; Mihaela Lascu

2006-07-01T23:59:59.000Z

48

Applied Optoelectronics | Open Energy Information  

Open Energy Info (EERE)

optical semiconductor devices, packaged optical components, optical subsystems, laser transmitters, and fiber optic transceivers. References Applied Optoelectronics1...

49

NFRC Procedures for Applied Films  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Films Applied Films Last update: 12/10/2013 07:29 PM NFRC now has a procedure for adding applied films to substrates in Optics5 and importing those applied film constructions into WINDOW5 to be used in a whole product calculation. The information presented below is provided to help simulators with this process. Feel free to contact us at WINDOWHelp@lbl.gov with questions or comments. NFRC Applied Film Procedure Applied Film Procedures (approved by NFRC) (PDF file) Approved Applied Film List (IGDB 33.0) (PDF file) NFRC Laminate Procedure Training Powerpoint with Examples (This Powerpoint presentation was used in the NFRC web based training sessions in December 2006 and January 2007) PowerPoint Presentation (PPT file) PowerPoint Presentation (PDF file) Help and Troubleshooting

50

Electricity Market Module  

U.S. Energy Information Administration (EIA) Indexed Site

Market Module Market Module This page inTenTionally lefT blank 101 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2013 Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules-electricity capacity planning, electricity fuel dispatching, electricity load and demand, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2013, DOE/EIA-M068(2013). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most

51

FY 1990 Applied Sciences Branch annual report  

DOE Green Energy (OSTI)

The Applied Sciences Branch actively supports the advancement of DOE/SERI goals for the development and implementation of the solar photovoltaic technology. The primary focus of the laboratories is to provide state-of-the-art analytical capabilities for materials and device characterization and fabrication. The branch houses a comprehensive facility which is capable of providing information on the full range of photovoltaic components. A major objective of the branch is to aggressively pursue collaborative research with other government laboratories, universities, and industrial firms for the advancement of photovoltaic technologies. Members of the branch disseminate research findings to the technical community in publications and presentations. This report contains information on surface and interface analysis, materials characterization, development, electro-optical characterization module testing and performance, surface interactions and FTIR spectroscopy.

Keyes, B.M.; Dippo, P.C. (eds.)

1991-11-01T23:59:59.000Z

52

Cyber Security Module  

NLE Websites -- All DOE Office Websites (Extended Search)

Cyber Security Module Cyber security training is required for all facility users and must be submitted before or upon arrival at the GUV Center. System Requirements and Information...

53

Detailed Course Module Description  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Course Module Description Course Module Description Module/Learning Objectives Level of Detail in Module by Audience Consumers Gen Ed/ Community College Trades 1. Energy Issues and Building Solutions High High High Learning Objectives: * Define terms of building science, ecological systems, economics of consumption * Relate building science perspective, ecology, social science * Explain historical energy and environmental issues related to buildings * Compare Site and source energy * Examine the health, safety and comfort issues in buildings * Examine the general context for building solutions (zero energy green home with durability as the goal) * Explain a basic overview of alternative energy (total solar flux) - do we have enough energy * Examine cash flow to homeowners

54

Macroeconomic Activity Module  

Annual Energy Outlook 2012 (EIA)

d022412A. U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 18 Macroeconomic Activity Module To reflect uncertainty in the projection of...

55

International Energy Module  

Reports and Publications (EIA)

Summarizes the overall structure of the International Energy Model and its interface with other NEMS modules, mathematical specifications of behavioral relationships, and data sources and estimation methods.

Adrian Geagla

2012-11-05T23:59:59.000Z

56

International Energy Module  

Reports and Publications (EIA)

Summarizes the overall structure of the International Energy Model and its interface with other NEMS modules, mathematical specifications of behavioral relationships, and data sources and estimation methods.

Adrian Geagla

2013-10-22T23:59:59.000Z

57

Digital intermediate frequency QAM modulator using parallel processing  

DOE Patents (OSTI)

The digital Intermediate Frequency (IF) modulator applies to various modulation types and offers a simple and low cost method to implement a high-speed digital IF modulator using field programmable gate arrays (FPGAs). The architecture eliminates multipliers and sequential processing by storing the pre-computed modulated cosine and sine carriers in ROM look-up-tables (LUTs). The high-speed input data stream is parallel processed using the corresponding LUTs, which reduces the main processing speed, allowing the use of low cost FPGAs.

Pao, Hsueh-Yuan (Livermore, CA); Tran, Binh-Nien (San Ramon, CA)

2008-05-27T23:59:59.000Z

58

Working with Modules within Python  

NLE Websites -- All DOE Office Websites (Extended Search)

Working with Modules within Perl and Python Working with Modules within Perl and Python Working with Modules within Perl and Python It can often be convenient to work with the modules system from within perl or python scripts. You can do this! Using Modules within Python The EnvironmentModules python package gives access to the module system from within python. The EnvironmentModules python package has a single function: module. Using this function you can provide the same arguments you would to "module" on the command line. The module() function accepts a list of arguments, like ['load','']; or ['unload','']. >>> import EnvironmentModules as EnvMod >>> EnvMod.module(['load','blast+']) It is important to understand that this is most effective for scripts

59

Macroeconomic Activity Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Macroeconomic Activity Module (MAM) used to develop the Annual Energy Outlook for 2013 (AEO2013). The report catalogues and describes the module assumptions, computations, methodology, parameter estimation techniques, and mainframe source code

2013-04-10T23:59:59.000Z

60

Membrane module assembly  

DOE Patents (OSTI)

A membrane module assembly is described which is adapted to provide a flow path for the incoming feed stream that forces it into prolonged heat-exchanging contact with a heating or cooling mechanism. Membrane separation processes employing the module assembly are also disclosed. The assembly is particularly useful for gas separation or pervaporation. 2 figures.

Kaschemekat, J.

1994-03-15T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Module Safety Issues (Presentation)  

SciTech Connect

Description of how to make PV modules so that they are less likely to turn into safety hazards. Making modules inherently safer with minimum additional cost is the preferred approach for PV. Safety starts with module design to ensure redundancy within the electrical circuitry to minimize open circuits and proper mounting instructions to prevent installation related ground faults. Module manufacturers must control the raw materials and processes to ensure that that every module is built like those qualified through the safety tests. This is the reason behind the QA task force effort to develop a 'Guideline for PV Module Manufacturing QA'. Periodic accelerated stress testing of production products is critical to validate the safety of the product. Combining safer PV modules with better systems designs is the ultimate goal. This should be especially true for PV arrays on buildings. Use of lower voltage dc circuits - AC modules, DC-DC converters. Use of arc detectors and interrupters to detect arcs and open the circuits to extinguish the arcs.

Wohlgemuth, J.

2012-02-01T23:59:59.000Z

62

International Energy Module  

Gasoline and Diesel Fuel Update (EIA)

he International Energy Module determines changes in the world oil price and the supply prices of crude he International Energy Module determines changes in the world oil price and the supply prices of crude oils and petroleum products for import to the United States in response to changes in U.S. import requirements. A market clearing method is used to determine the price at which worldwide demand for oil is equal to the worldwide supply. The module determines new values for oil production and demand for regions outside the United States, along with a new world oil price that balances supply and demand in the international oil market. A detailed description of the International Energy Module is provided in the EIA publication, Model Documentation Report: The International Energy Module of the National Energy Modeling System, DOE/EIA-M071(06), (Washington, DC, February 2006).

63

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 51 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Industrial Demand Module The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 15 manufacturing and 6 non-manufacturing industries. The manufacturing industries are further subdivided into the energy- intensive manufacturing industries and nonenergy-intensive manufacturing industries (Table 6.1). The manufacturing industries are modeled through the use of a detailed process-flow or end-use accounting procedure, whereas the non- manufacturing industries are modeled with substantially less detail. The petroleum refining industry is not included in the Industrial Module, as it is simulated separately in the Petroleum Market Module of NEMS. The Industrial Module calculates

64

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 Industrial Demand Module The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 15 manufacturing and 6 non-manufacturing industries. The manufacturing industries are further subdivided into the energy- intensive manufacturing industries and non-energy-intensive manufacturing industries (Table 6.1). The manufacturing industries are modeled through the use of a detailed process-flow or end-use accounting procedure, whereas the non- manufacturing industries are modeled with substantially less detail. The petroleum refining industry is not included in the Industrial Demand Module, as it is simulated separately in the Petroleum Market Module of NEMS. The Industrial Demand Module calculates energy consumption for the four Census Regions (see Figure 5) and disaggregates the energy consumption

65

Commercial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 Commercial Demand Module The NEMS Commercial Sector Demand Module generates projections of commercial sector energy demand through 2035. The definition of the commercial sector is consistent with EIA's State Energy Data System (SEDS). That is, the commercial sector includes business establishments that are not engaged in transportation or in manufacturing or other types of industrial activity (e.g., agriculture, mining or construction). The bulk of commercial sector energy is consumed within buildings; however, street lights, pumps, bridges, and public services are also included if the establishment operating them is considered commercial. Since most of commercial energy consumption occurs in buildings, the commercial module relies on the data from the EIA

66

Sonication standard laboratory module  

DOE Patents (OSTI)

A standard laboratory module for automatically producing a solution of cominants from a soil sample. A sonication tip agitates a solution containing the soil sample in a beaker while a stepper motor rotates the sample. An aspirator tube, connected to a vacuum, draws the upper layer of solution from the beaker through a filter and into another beaker. This beaker can thereafter be removed for analysis of the solution. The standard laboratory module encloses an embedded controller providing process control, status feedback information and maintenance procedures for the equipment and operations within the standard laboratory module.

Beugelsdijk, Tony (Los Alamos, NM); Hollen, Robert M. (Los Alamos, NM); Erkkila, Tracy H. (Los Alamos, NM); Bronisz, Lawrence E. (Los Alamos, NM); Roybal, Jeffrey E. (Santa Fe, NM); Clark, Michael Leon (Menan, ID)

1999-01-01T23:59:59.000Z

67

Water heater control module  

DOE Patents (OSTI)

An advanced electric water heater control system that interfaces with a high temperature cut-off thermostat and an upper regulating thermostat. The system includes a control module that is electrically connected to the high-temperature cut-off thermostat and the upper regulating thermostat. The control module includes a switch to open or close the high-temperature cut-off thermostat and the upper regulating thermostat. The control module further includes circuitry configured to control said switch in response to a signal selected from the group of an autonomous signal, a communicated signal, and combinations thereof.

Hammerstrom, Donald J

2013-11-26T23:59:59.000Z

68

Enhanced heat transfer for thermionic power modules  

DOE Green Energy (OSTI)

The thermionic power module is capable of operating at very high heat fluxes, which in turn serve to reduce capital costs. The most efficient operation also requires uniform heat fluxes. The development of enhanced heat transfer systems is required to meet the demand for high heat fluxes (>20 w/cm/sup 2/) at high temperatures (>1500K) which advanced thermionic power modules place upon combustion systems. Energy transfer from the hot combustion gases may take place by convection, radiation, or a combination of radiation and convection. Enhanced convective heat transfer with a jet impingement system has been demonstrated in a thermionic converter. The recently-developed cellular ceramic radiative heat transfer system has also been applied to a thermionic converter. By comparing the jet impingement and cellular ceramic radiative heat transfer systems, an appropriate system may be selected for utilization in advanced thermionic power modules. Results are reported.

Johnson, D.C.

1981-07-01T23:59:59.000Z

69

Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 95 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules-electricity capacity planning, electricity fuel dispatching, electricity load and demand, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2011, DOE/EIA-M068(2011). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most

70

CIM - compact intensity modulation.  

SciTech Connect

Compact intensity modulation (CIM), a new method to modulate the intensity of a neutron beam is demonstrated. CIM allows the production of arbitrary signals where the focus point can be chosen and changed without any constraints. A novel feature in this technique compared to spin echo techniques is that the neutron polarization is kept parallel or anti-parallel to the static fields during the passage through the magnetic fields and the beating pattern at the detector is produced by an amplitude modulation (AM) of the adiabatic RF-spin flippers rather than Larmor precession like in neutron spin echo (NSE) instruments; thus, the achievable contrast is very high and the instrument resolution can be changed very quickly. This gives the fascinating possibility at pulsed neutron sources to sweep the modulation frequency of the flippers in order to increase dynamic resolution range during the same neutron pulse.

Bleuel, M.; Lang, E.; Gahler, G.; Lal, J.; Intense Pulsed Neutron Source; Inst. Lau Langevin

2008-07-21T23:59:59.000Z

71

Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

This page inTenTionally lefT blank 91 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules-electricity capacity planning, electricity fuel dispatching, electricity load and demand, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2012, DOE/EIA-M068(2012). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most

72

Liquid Fuels Market Module  

U.S. Energy Information Administration (EIA) Indexed Site

Liquid Fuels Market Module Liquid Fuels Market Module This page inTenTionally lefT blank 145 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2013 Liquid Fuels Market Module The NEMS Liquid Fuels Market Module (LFMM) projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, unfinished oil imports, other refinery inputs (including alcohols, ethers, esters, corn, biomass, and coal), natural gas plant liquids production, and refinery processing gain. In addition, the LFMM projects capacity expansion and fuel consumption at domestic refineries. The LFMM contains a linear programming (LP) representation of U.S. petroleum refining

73

Residential Demand Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 Residential Demand Module The NEMS Residential Demand Module projects future residential sector energy requirements based on projections of the number of households and the stock, efficiency, and intensity of energy-consuming equipment. The Residential Demand Module projections begin with a base year estimate of the housing stock, the types and numbers of energy-consuming appliances servicing the stock, and the "unit energy consumption" (UEC) by appliance (in million Btu per household per year). The projection process adds new housing units to the stock, determines the equipment installed in new units, retires existing housing units, and retires and replaces appliances. The primary exogenous drivers for the module are housing starts by type

74

Digital optical conversion module  

DOE Patents (OSTI)

A digital optical conversion module used to convert an analog signal to a computer compatible digital signal including a voltage-to-frequency converter, frequency offset response circuitry, and an electrical-to-optical converter. Also used in conjunction with the digital optical conversion module is an optical link and an interface at the computer for converting the optical signal back to an electrical signal. Suitable for use in hostile environments having high levels of electromagnetic interference, the conversion module retains high resolution of the analog signal while eliminating the potential for errors due to noise and interference. The module can be used to link analog output scientific equipment such as an electrometer used with a mass spectrometer to a computer.

Kotter, Dale K. (North Shelley, ID); Rankin, Richard A. (Ammon, ID)

1991-02-26T23:59:59.000Z

75

Flywheel Energy Storage Module  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

kWh100 kW Flywheel Energy Storage Module * 100KWh - 18 cost KWh vs. current State of the Art * Bonded Magnetic Bearings on Rim ID * No Shaft Hub (which limits surface speed)...

76

Digital optical conversion module  

DOE Patents (OSTI)

A digital optical conversion module used to convert an analog signal to a computer compatible digital signal including a voltage-to-frequency converter, frequency offset response circuitry, and an electrical-to-optical converter. Also used in conjunction with the digital optical conversion module is an optical link and an interface at the computer for converting the optical signal back to an electrical signal. Suitable for use in hostile environments having high levels of electromagnetic interference, the conversion module retains high resolution of the analog signal while eliminating the potential for errors due to noise and interference. The module can be used to link analog output scientific equipment such as an electrometer used with a mass spectrometer to a computer. 2 figs.

Kotter, D.K.; Rankin, R.A.

1988-07-19T23:59:59.000Z

77

Residential Sector Demand Module  

Reports and Publications (EIA)

Model Documentation - Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

Owen Comstock

2012-12-19T23:59:59.000Z

78

Industrial Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Module. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code.

Kelly Perl

2013-05-14T23:59:59.000Z

79

Industrial Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Module. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code.

Kelly Perl

2013-09-30T23:59:59.000Z

80

Residential Sector Demand Module  

Reports and Publications (EIA)

Model Documentation - Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

Owen Comstock

2013-11-05T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Renewable Fuels Module  

Reports and Publications (EIA)

This report documents the objectives, analytical approach, and design of the National Energy Modeling System (NEMS) Renewable Fuels Module (RFM) as it relates to the production of the Annual Energy Outlook forecasts.

Chris Namovicz

2013-07-03T23:59:59.000Z

82

Renewable Fuels Module This  

U.S. Energy Information Administration (EIA) Indexed Site

Fuels Module Fuels Module This page inTenTionally lefT blank 175 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2013 Renewable Fuels Module The NEMS Renewable Fuels Module (RFM) provides natural resources supply and technology input information for projections of new central-station U.S. electricity generating capacity using renewable energy resources. The RFM has seven submodules representing various renewable energy sources: biomass, geothermal, conventional hydroelectricity, landfill gas, solar thermal, solar photovoltaics, and wind [1]. Some renewables, such as landfill gas (LFG) from municipal solid waste (MSW) and other biomass materials, are fuels in the conventional sense of the word, while others, such as water, wind, and solar radiation, are energy sources that do not involve

83

Programmable synchronous communications module  

SciTech Connect

The functional characteristics of a programmable, synchronous serial communications CAMAC module with buffering in block format are described. Both bit and byte oriented protocols can be handled in full duplex depending on the program implemented. The main elements of the module are a Signetics 2652 Multi-Protocol Communications Controller, a Zilog Z-808 8 bit microprocessor with PROM and RAM, and FIFOs for buffering. (FS)

Horelick, D.

1979-10-01T23:59:59.000Z

84

Electricity Market Module  

Reports and Publications (EIA)

Documents the Electricity Market Module as it was used for the Annual Energy Outlook 2013. The Electricity Market Module (EMM) is the electricity supply component of the National Energy Modeling System (NEMS). The EMM represents the generation, transmission, and pricing of electricity. It consists of four submodules: the Electricity Capacity Planning (ECP) Submodule, the Electricity Fuel Dispatch (EFD) Submodule, the Electricity Finance and Pricing (EFP) Submodule, and the Electricity Load and Demand (ELD) Submodule.

Jeff Jones

2013-07-24T23:59:59.000Z

85

Photovoltaic module reliability workshop  

DOE Green Energy (OSTI)

The paper and presentations compiled in this volume form the Proceedings of the fourth in a series of Workshops sponsored by Solar Energy Research Institute (SERI/DOE) under the general theme of photovoltaic module reliability during the period 1986--1990. The reliability Photo Voltaic (PV) modules/systems is exceedingly important along with the initial cost and efficiency of modules if the PV technology has to make a major impact in the power generation market, and for it to compete with the conventional electricity producing technologies. The reliability of photovoltaic modules has progressed significantly in the last few years as evidenced by warranties available on commercial modules of as long as 12 years. However, there is still need for substantial research and testing required to improve module field reliability to levels of 30 years or more. Several small groups of researchers are involved in this research, development, and monitoring activity around the world. In the US, PV manufacturers, DOE laboratories, electric utilities and others are engaged in the photovoltaic reliability research and testing. This group of researchers and others interested in this field were brought together under SERI/DOE sponsorship to exchange the technical knowledge and field experience as related to current information in this important field. The papers presented here reflect this effort.

Mrig, L. (ed.)

1990-01-01T23:59:59.000Z

86

BNL | Accelerators for Applied Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Accelerators for Applied Research Accelerators for Applied Research Brookhaven National Lab operates several accelerator facilities dedicated to applied research. These facilities directly address questions and concerns on a tremendous range of fields, including medical imaging, cancer therapy, computation, and space exploration. Leading scientists lend their expertise to these accelerators and offer crucial assistant to collaborating researchers, pushing the limits of science and technology. Interested in gaining access to these facilities for research? See the contact number listed for each facility. RHIC tunnel Brookhaven Linac Isotope Producer The Brookhaven Linac Isoptope Producer (BLIP)-positioned at the forefront of research into radioisotopes used in cancer treatment and diagnosis-produces commercially unavailable radioisotopes for use by the

87

Gradient Combinatorial Libraries via Modulated Light ...  

Science Conference Proceedings (OSTI)

... Libraries via Modulated Light Exposure. Bookmark and Share Gradient Combinatorial Libraries via Modulated Light Exposure. ...

88

CRC handbook of applied thermodynamics  

Science Conference Proceedings (OSTI)

The emphasis of this book is on applied thermodynamics, featuring the stage of development of a process rather than the logical development of thermodynamic principles. It is organized according to the types of problems encountered in industry, such as probing research, process assessment, and process development. The applied principles presented can be used in most areas of industry including oil and gas production and processing, chemical processing, power generation, polymer production, food processing, synthetic fuels production, specialty chemicals and pharmaceuticals production, bioengineered processes, etc.

Palmer, D.A. (Amoco Chemical Corp., Naperville, IL (USA). Research and Development Dept.)

1987-01-01T23:59:59.000Z

89

California Energy Commission Apply Today!  

E-Print Network (OSTI)

photovoltaic project in the future. Peak Demand Savings: 95 kW Energy Savings: 1,510,849 kWh Annual Energy CostCalifornia Energy Commission Apply Today! "The College implemented all of the recommended projects Programs Office (916) 654-4147 pubprog@energy.state.ca.us "CEC financing allowed us to install many

90

implementing bioenergy applied research & development  

E-Print Network (OSTI)

1 A Northern Centre for Renewable Energy implementing bioenergy applied research & development plant measures to become carbon neutral and operate on renewable energy. UNBC is uniquely positioned for Climate Solutions, and UNBC. The Green University Centre will be a model of energy efficiency

Northern British Columbia, University of

91

Vehicle Technologies Office: Applied Battery Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Battery Research to someone by E-mail Share Vehicle Technologies Office: Applied Battery Research on Facebook Tweet about Vehicle Technologies Office: Applied Battery...

92

Selective chemical detection by energy modulation of sensors  

DOE Patents (OSTI)

A portable instrument for use in the field in detecting, identifying, and quantifying a component of a sampled fluid includes a sensor which chemically reacts with the component of interest or a derivative thereof, an electrical heating filament for heating the sample before it is applied to the sensor, and modulating means for continuously varying the temperature of the filament (and hence the reaction rate) between two values sufficient to produce the chemical reaction. In response to this thermal modulation, the sensor produces a modulated output signal, the modulation of which is a function of the activation energy of the chemical reaction, which activation energy is specific to the particular component of interest and its concentration. Microprocessor means compares the modulated output signal with standard responses for a plurality of components to identify and quantify the particular component of interest. 4 figs.

Stetter, J.R.; Otagawa, T.

1985-05-20T23:59:59.000Z

93

CX-007739: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination University of Colorado - Boulder - Wafer-Level Sub-Module Integrated DCDC Converter CX(s) Applied: A9, B3.6 Date: 11302011 Location(s): Colorado,...

94

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Scalable Light Module for Low-Cost, High-Efficiency Light Emitting Diode Luminaires CX(s) Applied: B3.6 Date: 06112013 Location(s): Georgia...

95

Categorical Exclusion Determinations: B3.6 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Scalable Light Module for Low-Cost, High-Efficiency Light Emitting Diode Luminaires CX(s) Applied: B3.6 Date: 06112013 Location(s): Georgia...

96

CX-010461: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Scalable Light Module for Low-Cost, High-Efficiency Light Emitting Diode Luminaires CX(s) Applied: B3.6 Date: 06112013 Location(s): Georgia...

97

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Angeles - Solid State Cooling: Compact Micro Electro Mechanical Systems Electrocaloric Cooling Module CX(s) Applied: B3.6 Date: 08042010 Location(s): California Office(s):...

98

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CX-003536: Categorical Exclusion Determination High-Bandwidth Modulation of HydrogenSyngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08262010 Location(s):...

99

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

-High Performance Gallium Nitride High Electron Mobility Transistor Modules for Agile Power Electronics CX(s) Applied: B3.6 Date: 08052010 Location(s): California Office(s):...

100

Coal Market Module  

Gasoline and Diesel Fuel Update (EIA)

page intentionally left blank page intentionally left blank 153 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Coal Market Module The NEMS Coal Market Module (CMM) provides projections of U.S. coal production, consumption, exports, imports, distribution, and prices. The CMM comprises three functional areas: coal production, coal distribution, and coal exports. A detailed description of the CMM is provided in the EIA publication, Coal Market Module of the National Energy Modeling System 2011, DOE/EIA-M060(2011) (Washington, DC, 2011). Key assumptions Coal production The coal production submodule of the CMM generates a different set of supply curves for the CMM for each year of the projection. Forty-one separate supply curves are developed for each of 14 supply regions, nine coal types (unique combinations

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Commercial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

4 4 The commercial module forecasts consumption by fuel 15 at the Census division level using prices from the NEMS energy supply modules, and macroeconomic variables from the NEMS Macroeconomic Activity Module (MAM), as well as external data sources (technology characterizations, for example). Energy demands are forecast for ten end-use services 16 for eleven building categories 17 in each of the nine Census divisions (see Figure 5). The model begins by developing forecasts of floorspace for the 99 building category and Census division combinations. Next, the ten end-use service demands required for the projected floorspace are developed. The electricity generation and water and space heating supplied by distributed generation and combined heat and power technologies are projected. Technologies are then

102

Macroeconomic Activity Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 19 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook2011 Macroeconomic Activity Module The Macroeconomic Activity Module (MAM) represents the interaction between the U.S. economy as a whole and energy markets. The rate of growth of the economy, measured by the growth in gross domestic product (GDP) is a key determinant of the growth in demand for energy. Associated economic factors, such as interest rates and disposable income, strongly influence various elements of the supply and demand for energy. At the same time, reactions to energy markets by the aggregate economy, such as a slowdown in economic growth resulting from increasing energy prices, are also reflected in this module.

103

Coal Market Module This  

Gasoline and Diesel Fuel Update (EIA)

51 51 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Coal Market Module The NEMS Coal Market Module (CMM) provides projections of U.S. coal production, consumption, exports, imports, distribution, and prices. The CMM comprises three functional areas: coal production, coal distribution, and coal exports. A detailed description of the CMM is provided in the EIA publication, Coal Market Module of the National Energy Modeling System 2012, DOE/EIA-M060(2012) (Washington, DC, 2012). Key assumptions Coal production The coal production submodule of the CMM generates a different set of supply curves for the CMM for each year of the projection. Forty-one separate supply curves are developed for each of 14 supply regions, nine coal types (unique combinations

104

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 12 manufacturing and 6 nonmanufacturing industries. The manufacturing industries are further subdivided into the energy-intensive manufacturing industries and nonenergy-intensive manufacturing industries. The manufacturing industries are modeled through the use of a detailed process flow or end use accounting procedure, whereas the nonmanufacturing industries are modeled with substantially less detail (Table 17). The Industrial Demand Module forecasts energy consumption at the four Census region level (see Figure 5); energy consumption at the Census Division level is estimated by allocating the Census region forecast using the SEDS 27 data.

105

1 Modules and exactness  

E-Print Network (OSTI)

Suppose that R is an associative ring with 1. In most commutative cases, R is either the integers Z or some field k. Example: Suppose that k is a field and G is a group. The group-algebra k(G) over k is the direct sum k(G) = ? k, g?G with elements written as finite sums ? g?G ?g g, with ?g ? k and all but finitely many ?g = 0. The rule (?g g)(?h h) = (?g?h) (gh) defines the algebra structure on k(G), with multiplicative identity 1 = 1 e, where e is the identity element of G. A k(G)-module M is a k-vector space M, with bilinear map ? : k(G) M ? M with (r, m) ? ? r?m, such that r?(s?m) = (rs)? m and 1 ? m = m, or equivalently M is a k-vector 1 space equipped with a group homomorphism G ? Autk(M). k(G)-modules are often called G-modules for that reason. Not even that is the most enlightened way to describe a k(G)-module. A group G can be thought of as a category (actually a groupoid) with one object ? and a morphism ? g ? ? ? for every g ? G. Then a k(G)-module is a functor M: G ? k ? Mod which takes values in the category of k-vector spaces. NB: Ive only based these notions on fields k and their vector spaces to make them seem real. The object k could be a ring; then k(G) is a k-algebra still and a k(G)-module is a k-module M equipped with a group homomorphism G ? Autk(M). Now we recall some basic definitions and facts about R-modules. Suppose that f: M ? N is an R-module homomorphism. Then the kernel ker(f) of f is defined by ker(f) = {all x ? M such that f(x) = 0}. ker(f) is plainly a submodule of M. The image 2 im(f) of f is the submodule of N consisting of all y ? N such that y = f(x) for some x ? M. The cokernel of f cok(f) is defined to be the quotient A sequence cok(f) = N / im(f). M f ? ? M ? g ? ? M of R-module homomorphisms is said to be exact if ker(g) = im(f). Equivalently, the sequence is exact if g f = 0 and for all y ? M ? with g(y) = 0 there is an x ? M such that f(x) = y. A sequence M1 ? M2 ? ? Mn of R-module homomorphisms is said to be exact if ker = im everywhere. Example 1.1. The sequence 0 ? ker(f) ? M f ? ? N ? cok(f) ? 0 is exact for all R-module homomorphisms f. Note that 0 ? M f ? ? N is exact if and only if f is a monomorphism (injective), and that

unknown authors

2009-01-01T23:59:59.000Z

106

Power module assembly  

SciTech Connect

A power module assembly of the type suitable for deployment in a vehicular power inverter, wherein the power inverter has a grounded chassis, is provided. The power module assembly comprises a conductive base layer electrically coupled to the chassis, an insulating layer disposed on the conductive base layer, a first conductive node disposed on the insulating layer, a second conductive node disposed on the insulating layer, wherein the first and second conductive nodes are electrically isolated from each other. The power module assembly also comprises a first capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the first conductive node, and further comprises a second capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the second conductive node.

Campbell, Jeremy B. (Torrance, CA); Newson, Steve (Redondo Beach, CA)

2011-11-15T23:59:59.000Z

107

Remote Gas Well Monitoring Technology Applied to Marcellus Shale Site |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Remote Gas Well Monitoring Technology Applied to Marcellus Shale Remote Gas Well Monitoring Technology Applied to Marcellus Shale Site Remote Gas Well Monitoring Technology Applied to Marcellus Shale Site February 10, 2012 - 12:00pm Addthis Washington, DC - A technology to remotely monitor conditions at energy-rich Marcellus Shale gas wells to help insure compliance with environmental requirements has been developed through a research partnership funded by the U.S. Department of Energy (DOE). NETL-RUA researcher Dr. Michael McCawley hasdeveloped a technology to remotely monitor theenvironment around energy-rich Marcellus Shale gas wells. Photo courtesy of West Virginia University.The technology - which involves three wireless monitoring modules to measure volatile organic compounds, dust, light and sound - is currently being tested at a Marcellus

108

Photovoltaic module and interlocked stack of photovoltaic modules  

DOE Patents (OSTI)

One embodiment relates to an arrangement of photovoltaic modules configured for transportation. The arrangement includes a plurality of photovoltaic modules, each photovoltaic module including a frame having at least a top member and a bottom member. A plurality of alignment features are included on the top member of each frame, and a plurality of alignment features are included on the bottom member of each frame. Adjacent photovoltaic modules are interlocked by the alignment features on the top member of a lower module fitting together with the alignment features on the bottom member of an upper module. Other embodiments, features and aspects are also disclosed.

Wares, Brian S.

2012-09-04T23:59:59.000Z

109

Test-to-Failure of Crystalline Silicon Modules: Preprint  

DOE Green Energy (OSTI)

Accelerated lifetime testing of five crystalline silicon module designs was carried out according to the Terrestrial Photovoltaic Module Accelerated Test-to-Failure Protocol. This protocol compares the reliability of various module constructions on a quantitative basis. The modules under test are subdivided into three accelerated lifetime testing paths: 85..deg..C/85% relative humidity with system bias, thermal cycling between ?40..deg..C and 85..deg..C, and a path that alternates between damp heat and thermal cycling. The most severe stressor is damp heat with system bias applied to simulate the voltages that modules experience when connected in an array. Positive 600 V applied to the active layer with respect to the grounded module frame accelerates corrosion of the silver grid fingers and degrades the silicon nitride antireflective coating on the cells. Dark I-V curve fitting indicates increased series resistance and saturation current around the maximum power point; however, an improvement in junction recombination characteristics is obtained. Shunt paths and cell-metallization interface failures are seen developing in the silicon cells as determined by electroluminescence, thermal imaging, and I-V curves in the case of negative 600 V bias applied to the active layer. Ability to withstand electrolytic corrosion, moisture ingress, and ion drift under system voltage bias are differentiated.

Hacke, P.; Terwilliger, K.; Glick, S.; Trudell, D.; Bosco, N.; Johnston, S.; Kurtz, S. R.

2010-10-01T23:59:59.000Z

110

Method of monolithic module assembly  

DOE Patents (OSTI)

Methods for "monolithic module assembly" which translate many of the advantages of monolithic module construction of thin-film PV modules to wafered c-Si PV modules. Methods employ using back-contact solar cells positioned atop electrically conductive circuit elements affixed to a planar support so that a circuit capable of generating electric power is created. The modules are encapsulated using encapsulant materials such as EVA which are commonly used in photovoltaic module manufacture. The methods of the invention allow multiple cells to be electrically connected in a single encapsulation step rather than by sequential soldering which characterizes the currently used commercial practices.

Gee, James M. (Albuquerque, NM); Garrett, Stephen E. (Albuquerque, NM); Morgan, William P. (Albuquerque, NM); Worobey, Walter (Albuquerque, NM)

1999-01-01T23:59:59.000Z

111

Commercial Sector Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Commercial Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated through the synthesis and scenario development based on these components.

Kevin Jarzomski

2012-11-15T23:59:59.000Z

112

Coal Market Module  

Reports and Publications (EIA)

Documents the objectives and the conceptual and methodological approach used in the development of the National Energy Modeling System's (NEMS) Coal Market Module (CMM) used to develop the Annual Energy Outlook 2013 (AEO2013). This report catalogues and describes the assumptions, methodology, estimation techniques, and source code of CMM's two submodules. These are the Coal Production Submodule (CPS) and the Coal Distribution Submodule (CDS).

Michael Mellish

2013-07-17T23:59:59.000Z

113

Commercial Sector Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Commercial Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated through the synthesis and scenario development based on these components.

Kevin Jarzomski

2013-10-10T23:59:59.000Z

114

Pulse width modulation inverter with battery charger  

SciTech Connect

An inverter is connected between a source of DC power and a three-phase AC induction motor, and a microprocessor-based circuit controls the inverter using pulse width modulation techniques. In the disclosed method of pulse width modulation, both edges of each pulse of a carrier pulse train are equally modulated by a time proportional to sin [theta], where [theta] is the angular displacement of the pulse center at the motor stator frequency from a fixed reference point on the carrier waveform. The carrier waveform frequency is a multiple of the motor stator frequency. The modulated pulse train is then applied to each of the motor phase inputs with respective phase shifts of 120[degree] at the stator frequency. Switching control commands for electronic switches in the inverter are stored in a random access memory (RAM) and the locations of the RAM are successively read out in a cyclic manner, each bit of a given RAM location controlling a respective phase input of the motor. The DC power source preferably comprises rechargeable batteries and all but one of the electronic switches in the inverter can be disabled, the remaining electronic switch being part of a flyback'' DC-DC converter circuit for recharging the battery. 11 figs.

Slicker, J.M.

1985-01-01T23:59:59.000Z

115

Pulse width modulation inverter with battery charger  

SciTech Connect

An inverter is connected between a source of DC power and a three-phase AC induction motor, and a microprocessor-based circuit controls the inverter using pulse width modulation techniques. In the disclosed method of pulse width modulation, both edges of each pulse of a carrier pulse train are equally modulated by a time proportional to sin .theta., where .theta. is the angular displacement of the pulse center at the motor stator frequency from a fixed reference point on the carrier waveform. The carrier waveform frequency is a multiple of the motor stator frequency. The modulated pulse train is then applied to each of the motor phase inputs with respective phase shifts of 120.degree. at the stator frequency. Switching control commands for electronic switches in the inverter are stored in a random access memory (RAM) and the locations of the RAM are successively read out in a cyclic manner, each bit of a given RAM location controlling a respective phase input of the motor. The DC power source preferably comprises rechargeable batteries and all but one of the electronic switches in the inverter can be disabled, the remaining electronic switch being part of a "flyback" DC-DC converter circuit for recharging the battery.

Slicker, James M. (Union Lake, MI)

1985-01-01T23:59:59.000Z

116

THREE ESSAYS ON APPLIED ECONOMICS  

E-Print Network (OSTI)

In this dissertation three essays were presented. In the first two essays we measure the consumer welfare changes caused by U.S. meat price changes. In the third essay the dynamic structure of international gasoline prices using the time series methodology is investigated. In chapter II, we investigate the U.S. consumer behavior on meat consumption depending on a linear expenditure system (LES), and then we simulate the welfare effects of a set of price changes on the U.S. meat consumption. The simulation results show that the amount of consumer welfare change for each meat is not same across the meats under the same percentage change of price. The simulation results also show that when all the prices are doubled the total amount of CV reaches almost the same amount of current total quarterly expenditures for the three meats. In chapter III, we apply the compensating variation (CV) approach for the measurement of consumer welfare losses associated with beef price changes. We applied the long-run cointegrating relationship in vector error correction model (VECM) to estimate the Marshallian demand function. Apparently, the use of long-run cointegration in VECM in deriving the direct Marshallian demand function to measure the consumer welfare change is the first attempt in the literature. This is one of the contributions of the study. The simulation results show that the amount of consumer welfare change for beef is compatible with the one derived from LES methodology. In chapter IV, an empirical framework to summarize the interdependence of four international gasoline markets (New York, U.S. Gulf Coast, Rotterdam and Singapore) is presented. For that purpose, we employ a structural VECM and directed acyclic graphs (DAGs). To solve the identification problem in structural VECM, we apply DAGs derived from contemporaneous VECM innovations. The impulse response functions show that the time period in which a shock in a market affects the other market is very short. Forecast error variance decompositions (FEVD) shows that in all markets, except the U.S. Gulf Coast market, current and past shocks in their own market explained the most of the volatility in their own market in the Short-run.

Shin, Sang-Cheol

2008-08-01T23:59:59.000Z

117

Module Utilization Committee. Final report  

DOE Green Energy (OSTI)

Photovoltaic collector modules were declared surplus to the needs of the US Department of Energy. The Module Utilization Committee was formed to make appropriate disposition of the surplus modules. The final report of that committee accounts for that disposition. The membership and activities of the committee are set forth and the results of its activities are reported.

None

1984-03-01T23:59:59.000Z

118

Applied Materials | Open Energy Information  

Open Energy Info (EERE)

Materials Materials Jump to: navigation, search Name Applied Materials Address 3050 Bowers Avenue Place Santa Clara, California Zip 95054 Sector Solar Stock Symbol AMAT Website http://www.appliedmaterials.co Coordinates 37.3775749°, -121.9794416° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.3775749,"lon":-121.9794416,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

119

International Energy Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 International Energy Module The NEMS International Energy Module (IEM) simulates the interaction between U.S. and global petroleum markets. It uses assumptions of economic growth and expectations of future U.S. and world crude-like liquids production and consumption to estimate the effects of changes in U.S. liquid fuels markets on the international petroleum market. For each year of the forecast, the NEMS IEM computes oil prices, provides a supply curve of world crude-like liquids, generates a worldwide oil supply- demand balance with regional detail, and computes quantities of crude oil and light and heavy petroleum products imported into the United States by export region. Changes in the oil price (WTI), which is defined as the price of light, low-sulfur crude oil delivered to Cushing, Oklahoma in

120

International Energy Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 23 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 International Energy Module The NEMS International Energy Module (IEM) simulates the interaction between U.S. and global petroleum markets. It uses assumptions of economic growth and expectations of future U.S. and world crude-like liquids production and consumption to estimate the effects of changes in U.S. liquid fuels markets on the international petroleum market. For each year of the forecast, the NEMS IEM computes world oil prices, provides a supply curve of world crude-like liquids, generates a worldwide oil supply- demand balance with regional detail, and computes quantities of crude oil and light and heavy petroleum products imported into

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Commercial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 39 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Commercial Demand Module The NEMS Commercial Sector Demand Module generates projections of commercial sector energy demand through 2035. The definition of the commercial sector is consistent with EIA's State Energy Data System (SEDS). That is, the commercial sector includes business establishments that are not engaged in transportation or in manufacturing or other types of industrial activity (e.g., agriculture, mining or construction). The bulk of commercial sector energy is consumed within buildings; however, street lights, pumps, bridges, and public services are also included if the establishment operating them is considered commercial.

122

Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 137 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Petroleum Market Module The NEMS Petroleum Market Module (PMM) projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, unfinished oil imports, other refinery inputs (including alcohols, ethers, bioesters, corn, biomass, and coal), natural gas plant liquids production, and refinery processing gain. In addition, the PMM projects capacity expansion and fuel consumption at domestic refineries. The PMM contains a linear programming (LP) representation of U.S. refining activities in the five Petroleum Administration for

123

Renewable Fuels Module  

Gasoline and Diesel Fuel Update (EIA)

page intentionally left blank page intentionally left blank 167 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Renewable Fuels Module The NEMS Renewable Fuels Module (RFM) provides natural resources supply and technology input information for projections of new central-station U.S. electricity generating capacity using renewable energy resources. The RFM has seven submodules representing various renewable energy sources: biomass, geothermal, conventional hydroelectricity, landfill gas, solar thermal, solar photovoltaics, and wind [1]. Some renewables, such as landfill gas (LFG) from municipal solid waste (MSW) and other biomass materials, are fuels in the conventional sense of the word, while others, such as water, wind, and solar radiation, are energy sources that do not involve the

124

Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

This page inTenTionally lefT blank 135 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Petroleum Market Module The NEMS Petroleum Market Module (PMM) projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, unfinished oil imports, other refinery inputs (including alcohols, ethers, esters, corn, biomass, and coal), natural gas plant liquids production, and refinery processing gain. In addition, the PMM projects capacity expansion and fuel consumption at domestic refineries. The PMM contains a linear programming (LP) representation of U.S. refining activities in the five Petroleum Administration for

125

Flywheel Energy Storage Module  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

kWh/100 kW kWh/100 kW Flywheel Energy Storage Module * 100KWh - 1/8 cost / KWh vs. current State of the Art * Bonded Magnetic Bearings on Rim ID * No Shaft / Hub (which limits surface speed) * Flexible Motor Magnets on Rim ID * Develop Touch-down System for Earthquake Flying Rim Eliminate Shaft and Hub Levitate on Passive Magnetic Bearings Increase Rim Tip Speed Larger Diameter Thinner Rim Stores More Energy 4 X increase in Stored Energy with only 60% Increase in Weight Development of a 100 kWh/100 kW Flywheel Energy Storage Module High Speed, Low Cost, Composite Ring with Bore-Mounted Magnetics Current State of the Art Flywheel Limitations of Existing Flywheel * 15 Minutes of storage * Limited to Frequency Regulation Application * Rim Speed (Stored Energy) Limited by Hub Strain and Shaft Dynamics

126

EERE Postdoctoral Research Awards: How to Apply  

NLE Websites -- All DOE Office Websites (Extended Search)

How to Apply to someone by E-mail Share EERE Postdoctoral Research Awards: How to Apply on Facebook Tweet about EERE Postdoctoral Research Awards: How to Apply on Twitter Bookmark...

127

ETTM-HE (Heat Exchanger)CBT Module, Version 1.0  

Science Conference Proceedings (OSTI)

The Heat Exchangers Computer-Based Training/Engineering Technical Training Modules Course (HE CBT/ETTM) version 1.0 is a web-based training module that provides graphics and interactive features to enhance learning and theory of operation for a variety of heat exchangers. This application introduces the basic heat transfer principles of heat exchangers and how these principles apply to typical nuclear plant exchanger applications. This computer-based training (CBT) module is intended for use by new engi...

2006-10-31T23:59:59.000Z

128

Weatherization and Intergovernmental Program: Apply for Weatherization  

NLE Websites -- All DOE Office Websites (Extended Search)

Apply Apply for Weatherization Assistance to someone by E-mail Share Weatherization and Intergovernmental Program: Apply for Weatherization Assistance on Facebook Tweet about Weatherization and Intergovernmental Program: Apply for Weatherization Assistance on Twitter Bookmark Weatherization and Intergovernmental Program: Apply for Weatherization Assistance on Google Bookmark Weatherization and Intergovernmental Program: Apply for Weatherization Assistance on Delicious Rank Weatherization and Intergovernmental Program: Apply for Weatherization Assistance on Digg Find More places to share Weatherization and Intergovernmental Program: Apply for Weatherization Assistance on AddThis.com... Plans, Implementation, & Results Weatherization Assistance Program Weatherization Services

129

Vehicle Technologies Office: Applied Battery Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Battery Research Applied battery research addresses the barriers facing the lithium-ion systems that are closest to meeting the technical energy and power requirements for...

130

Photovoltaic module electrical termination design requirement study. Final report  

DOE Green Energy (OSTI)

Motorola Inc., in conjunction with ITT Cannon, has conducted a study to develop information to facilitate the selection of existing, commercial, electrical termination hardware for photovoltaic modules and arrays. Details of the study are presented in this volume. Module and array design parameters were investigated and recommendations were developed for use in surveying, evaluating, and comparing electrical termination hardware. Electrical termination selection criteria factors were developed and applied to nine generic termination types in each of the four application sectors. Remote, residential, intermediate and industrial. Existing terminations best suited for photovoltaic modules and arrays were identified. Cost information was developed to identify cost drivers and/or requirements which might lead to cost reductions. The general conclusion is that there is no single generic termination that is best suited for photovoltaic application, but that the appropriate termination is strongly dependent upon the module construction and its support structure as well as the specific application sector.

Mosna, F.J. Jr.; Donlinger, J.

1980-07-01T23:59:59.000Z

131

DARPA Learning Applied to Ground Robots (LAGR)  

Science Conference Proceedings (OSTI)

DARPA Learning Applied to Ground Robots (LAGR) Project (Concluded). Summary: The National Institute of Standards ...

2012-01-04T23:59:59.000Z

132

Engineering Technical Training Module Water and Steam Properties (ETTM: WSP) Version 1.0  

Science Conference Proceedings (OSTI)

The purpose of this training module is to provide a foundational understanding on the engineering principals and properties of water and steam and how they apply in nuclear power plant applications. The topics that are included are steam tables, specific heat, the energy equation and how it applies to different plant systems, and example problems for analyzing different plant equipment to understand their water/steam properties. This computer-based training (CBT) module is intended for use by new engine...

2011-09-16T23:59:59.000Z

133

Photovoltaic concentrator module improvements study  

DOE Green Energy (OSTI)

This report presents results of a project to design and fabricate an improved photovoltaic concentrator module. Using previous work as a baseline, this study conducted analyses and testing to select major module components and design features. The lens parquet and concentrator solar cell were selected from the highest performing, available components. A single 185X point-focus module was fabricated by the project team and tested at Sandia. Major module characteristics include a 6 by 4 compression-molded acrylic lens parquet (0.737 m{sup 2} area), twenty-four 0.2 ohms-cm, FZ, p-Si solar cells (1.56 cm{sup 2} area) soldered to ceramic substrates and copper heat spreaders, and an aluminized steel housing with corrugated bottom. This project marked the first attempt to use prismatic covers on solar cells in a high-concentration, point-focus application. Cells with 15 percent metallization were obtained, but problems with the fabrication and placement of prismatic covers on these cells lead to the decision not to use covers in the prototype module. Cell assembly fabrication, module fabrication, and module optical design activities are presented here. Test results are also presented for bare cells, cell assemblies, and module. At operating conditions of 981 watts/m{sup 2} DNI and an estimated cell temperature of 65{degrees}C, the module demonstrated an efficiency of 13.9 percent prior to stressed environmental exposure. 12 refs., 56 figs., 7 tabs.

Levy, S.L.; Kerschen, K.A. (Black and Veatch, Kansas City, MO (United States)); Hutchison, G. (Solar Kinetics, Inc., Dallas, TX (United States)); Nowlan, M.J. (Spire Corp., Bedford, MA (United States))

1991-08-01T23:59:59.000Z

134

Flat-Plate Photovoltaic Modules  

Energy.gov (U.S. Department of Energy (DOE))

Flat-plate photovoltaic (PV) modules are made of several components, including the front surface materials, encapsulant, rear surface, and frame.

135

WSRC Nuclear Materials Cost Module  

National Nuclear Security Administration (NNSA)

Office (GAO) WSRC NM Cost Module Generates WSRC monthly and fiscal year to date Inventory and Manufacturing Statement for government owned accountable nuclear materials....

136

Adjustable extender for instrument module  

DOE Patents (OSTI)

A blank extender module used to mount an instrument module in front of its console for repair or test purposes has been equipped with a rotatable mount and means for locking the mount at various angles of rotation for easy accessibility. The rotatable mount includes a horizontal conduit supported by bearings within the blank module. The conduit is spring-biased in a retracted position within the blank module and in this position a small gear mounted on the conduit periphery is locked by a fixed pawl. The conduit and instrument mount can be pulled into an extended position with the gear clearing the pawl to permit rotation and adjustment of the instrument.

Sevec, J.B.; Stein, A.D.

1975-11-01T23:59:59.000Z

137

Taught Masters Module Guide  

E-Print Network (OSTI)

Pests, parasites and pathogens II:: rabies, foot-and-mouth and nematode worms KW KW KW KW KW KW KW KW KW KW Practical/ workshop Title Lecturer 1 2 3 4 5 Collecting population data: small mammal trapping in applied population ecology; poster presentation and workshop KW KW KW KW KW Learning outcomes

Meju, Max

138

Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

other refinery inputs including alcohols, ethers, bioesters, other refinery inputs including alcohols, ethers, bioesters, natural gas plant liquids production, and refinery processing gain. In addition, the PMM estimates capacity expansion and fuel consumption of domestic refineries. The PMM contains a linear programming representation of U.S. refining activities in the five Petroleum Area Defense Districts (PADDs) (Figure 9). The model is created by aggregating individual refineries into one linear programmming representation for each PADD. This representation provides the marginal costs of production for a number of conventional and new petroleum products. In order to interact with other NEMS modules with different regional representations, certain PMM inputs and outputs are converted from PADD regions to other regional structures and vice versa. The linear programming results are used to determine

139

Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

6, DOE/EIA- 6, DOE/EIA- M068(2006). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most economical way to supply electricity, within environmental and operational constraints. There are assumptions about the operations of the electricity sector and the costs of various options in each of the EMM submodules. This section describes the model parameters and assumptions used in EMM. It includes a discussion of legislation and regulations that are incorporated in EMM as well as information about the climate change action plan. The various electricity and technology cases are also described. EMM Regions The supply regions used in EMM are based on the North American Electric Reliability Council regions and

140

Photovoltaic module mounting system  

SciTech Connect

A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

Miros, Robert H. J. (Fairfax, CA); Mittan, Margaret Birmingham (Oakland, CA); Seery, Martin N. (San Rafael, CA); Holland, Rodney H. (Novato, CA)

2012-04-17T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Photovoltaic module mounting system  

SciTech Connect

A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

Miros, Robert H. J.; Mittan, Margaret Birmingham; Seery, Martin N; Holland, Rodney H

2012-09-18T23:59:59.000Z

142

Selective chemical detection by energy modulation of sensors  

DOE Patents (OSTI)

A portable instrument for use in the field in detecting, identifying, and quantifying a component of a sampled fluid includes a sensor which chemically reacts with the component of interest or a derivative thereof, an electrical heating filament for heating the sample before it is applied to the sensor, and modulator for continuously varying the temperature of the filament (and hence the reaction rate) between two values sufficient to produce the chemical reaction. In response to this thermal modulation, the sensor produces a modulated output signal, the modulation of which is a function of the activation energy of the chemical reaction, which activation energy is specific to the particular component of interest and its concentration. Microprocessor which compares the modulated output signal with standard responses for a plurality of components to identify and quantify the particular component of interest. In particular, the concentration of the component of interest is proportional to the amplitude of the modulated output signal, while the identifying activation output energy of the chemical interaction indicative of that component is proportional to a normalized parameter equal to the peak-to-peak amplitude divided by the height of the upper peaks above a base line signal level. 5 figures.

Stetter, J.R.; Otagawa, T.

1991-09-10T23:59:59.000Z

143

PRINCIPLE OF GLOBAL DECOUPLING WITH COUPLING ANGLE MODULATION.  

Science Conference Proceedings (OSTI)

The global betatron decoupling on the ramp is an important issue for the operation of the Relativistic Heavy Ion Collider (RHIC). A new scheme, coupling angle modulation, was found. By modulating two orthogonal skew quadrupole families, an extra rotating coupling is introduced into the coupled machine. The skew quadrupole modulation frequency is about 0.2Hz for the RHIC ramp, and 0.5Hz at injection and store. The eigentune changes are tracked with a high resolution phase lock loop (PLL) tune measurement system. The global coupling correction strengths are determined by the modulation skew quadrupole strengths at the minimum eigentune split multiplied by a factor k. k is determined by the uncoupled eigentune split and the maximum and the minimum tune split during the skew quadrupole modulation. This decoupling scheme is fast and robust. It had been verified at the RHIC and has been applied for the RHIC global decoupling on the ramp. In this article, the principle of the coupling angle modulation is presented in detail. Simulation results are also shown.

LUO, Y.; PILAT, F.; PEGGS, S.; TRBOJEVIC, D.; ROSER, T.

2005-05-16T23:59:59.000Z

144

Models of Photovoltaic Module Performance  

Science Conference Proceedings (OSTI)

An analysis of data collected over a three-year period at Pacific Gas and Electric Company's Photovoltaic Test Facility has enabled the prediction of photovoltaic (PV) module performance under conditions different from the test environment. The equations developed by PG&E provide a basis for rating photovoltaic modules and systems more accurately than in the past.

1988-09-01T23:59:59.000Z

145

Oxidation Kinetics Modeling Applying Phase Field Approach  

Science Conference Proceedings (OSTI)

Presentation Title, Oxidation Kinetics Modeling Applying Phase Field Approach ... chemical reaction rates will increase exponentially and environmental attack...

146

Applied Chemicals and Materials Staff Directory  

Science Conference Proceedings (OSTI)

Applied Chemicals and Materials Staff Directory. ... accept either a name, organizational name, or ... MML Organization. Contact. Material Measurement ...

2012-10-12T23:59:59.000Z

147

Researcher, Los Alamos National Laboratory - Applied Physics...  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Physics Division | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response...

148

Oil and Gas Supply Module  

U.S. Energy Information Administration (EIA) Indexed Site

Oil and Gas Supply Module Oil and Gas Supply Module This page inTenTionally lefT blank 119 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2013 Oil and Gas Supply Module The NEMS Oil and Gas Supply Module (OGSM) constitutes a comprehensive framework with which to analyze crude oil and natural gas exploration and development on a regional basis (Figure 8). The OGSM is organized into 4 submodules: Onshore Lower 48 Oil and Gas Supply Submodule, Offshore Oil and Gas Supply Submodule, Oil Shale Supply Submodule[1], and Alaska Oil and Gas Supply Submodule. A detailed description of the OGSM is provided in the EIA publication, Model Documentation Report: The Oil and Gas Supply Module (OGSM), DOE/EIA-M063(2011), (Washington, DC, 2011). The OGSM provides

149

CHEMICAL ENGINEERING SCHOOL OF ENGINEERING & APPLIED SCIENCE  

E-Print Network (OSTI)

30 CHEMICAL ENGINEERING SCHOOL OF ENGINEERING & APPLIED SCIENCE MIAMI UNIVERSITY 2005-2006 The program leads to the degree, Bachelor of Science in Applied Science, with a major in Chemical Engineering The chemical engineering students learn to apply the concepts of chemistry, biochemistry and biological science

Dollar, Anna

150

Force Modulator System  

SciTech Connect

Many metal parts manufacturers use large metal presses to shape sheet metal into finished products like car body parts, jet wing and fuselage surfaces, etc. These metal presses take sheet metal and - with enormous force - reshape the metal into a fully formed part in a manner of seconds. Although highly efficient, the forces involved in forming metal parts also damage the press itself, limit the metals used in part production, slow press operations and, when not properly controlled, cause the manufacture of large volumes of defective metal parts. To date, the metal-forming industry has not been able to develop a metal-holding technology that allows full control of press forces during the part forming process. This is of particular importance in the automotive lightweighting efforts under way in the US automotive manufacturing marketplace. Metalforming Controls Technology Inc. (MC2) has developed a patented press control system called the Force Modulator that has the ability to control these press forces, allowing a breakthrough in stamping process control. The technology includes a series of hydraulic cylinders that provide controlled tonnage at all points in the forming process. At the same time, the unique cylinder design allows for the generation of very high levels of clamping forces (very high tonnages) in very small spaces; a requirement for forming medium and large panels out of HSS and AHSS. Successful production application of these systems testing at multiple stamping operations - including Ford and Chrysler - has validated the capabilities and economic benefits of the system. Although this technology has been adopted in a number of stamping operations, one of the primary barriers to faster adoption and application of this technology in HSS projects is system cost. The cost issue has surfaced because the systems currently in use are built for each individual die as a custom application, thus driving higher tooling costs. This project proposed to better marry the die-specific Force Modulator technology with stamping presses in the form of a press cushion. This system would be designed to operate the binder ring for multiple parts, thus cutting the per-die cost of the technology. This study reports the results of technology field application. This project produced the following conclusions: (1) The Force Modulator system is capable of operating at very high tempos in the stamping environment; (2) The company can generate substantial, controlled holding tonnage (binder ring pressure) necessary to hold high strength steel parts for proper formation during draw operations; (3) A single system can be designed to operate with a family of parts, thus significantly reducing the per-die cost of a FM system; (4) High strength steel parts made with these systems appear to show significant quality improvements; (5) The amounts of steel required to make these parts is typically less than the amounts required with traditional blank-holding technologies; and (6) This technology will aid in the use of higher strength steels in auto and truck production, thus reducing weight and improving fuel efficiency.

Redmond Clark

2009-04-30T23:59:59.000Z

151

Photovoltaic solar concentrator module  

DOE Patents (OSTI)

This invention consists of a planar photovoltaic concentrator module for producing an electrical signal from incident solar radiation which includes an electrically insulating housing having a front wall, an opposing back wall and a hollow interior. A solar cell having electrical terminals is positioned within the interior of the housing. A planar conductor is connected with a terminal of the solar cell of the same polarity. A lens forming the front wall of the housing is operable to direct solar radiation incident to the lens into the interior of the housing. A refractive optical element in contact with the solar cell and facing the lens receives the solar radiation directed into the interior of the housing by the lens and directs the solar radiation to the solar cell to cause the solar cell to generate an electrical signal. An electrically conductive planar member is positioned in the housing to rest on the housing back wall in supporting relation with the solar cell terminal of opposite polarity. The planar member is operable to dissipate heat radiated by the solar cell as the solar cell generates an electrical signal and further forms a solar cell conductor connected with the solar cell terminal to permit the electrical signal generated by the solar cell to be measured between the planar member and the conductor.

Chiang, C.J.

1991-05-16T23:59:59.000Z

152

Living Systems Energy Module  

DOE Green Energy (OSTI)

The Living Systems Energy Module, renamed Voyage from the Sun, is a twenty-lesson curriculum designed to introduce students to the major ways in which energy is important in living systems. Voyage from the Sun tells the story of energy, describing its solar origins, how it is incorporated into living terrestrial systems through photosynthesis, how it flows from plants to herbivorous animals, and from herbivores to carnivores. A significant part of the unit is devoted to examining how humans use energy, and how human impact on natural habitats affects ecosystems. As students proceed through the unit, they read chapters of Voyage from the Sun, a comic book that describes the flow of energy in story form (Appendix A). During the course of the unit, an ``Energy Pyramid`` is erected in the classroom. This three-dimensional structure serves as a classroom exhibit, reminding students daily of the importance of energy and of the fragile nature of our living planet. Interactive activities teach students about adaptations that allow plants and animals to acquire, to use and to conserve energy. A complete list of curricular materials and copies of all activity sheets appear in Appendix B.

NONE

1995-09-26T23:59:59.000Z

153

Photovoltaic module with adhesion promoter  

SciTech Connect

Photovoltaic modules with adhesion promoters and methods for fabricating photovoltaic modules with adhesion promoters are described. A photovoltaic module includes a solar cell including a first surface and a second surface, the second surface including a plurality of interspaced back-side contacts. A first glass layer is coupled to the first surface by a first encapsulating layer. A second glass layer is coupled to the second surface by a second encapsulating layer. At least a portion of the second encapsulating layer is bonded directly to the plurality of interspaced back-side contacts by an adhesion promoter.

2013-10-08T23:59:59.000Z

154

Photovoltaic Cz Silicon Module Improvements  

DOE Green Energy (OSTI)

Work focused on reducing the cost per watt of Cz silicon photovoltaic modules under Phase II of Siemens Solar Industries' DOE/NREL PVMaT 4A subcontract is described in this report. New module designs were deployed in this phase of the contract, improvements in yield of over 10% were realized, and further implementation of Statistical Process Control was achieved during this phase. Module configurations representing a 12% cost reduction per watt were implemented in small scale production under Phase II of this contract. Yield improvements are described in detail, yield sensitivity to wafer thickness is quantified, and the deployment of SPC in critical process steps is reported here.

Jester, T. L.

1998-09-01T23:59:59.000Z

155

Residential Sector Demand Module 1995, Model Documentation  

Reports and Publications (EIA)

This updated version of the NEMS Residential Module Documentation includes changesmade to the residential module for the production of the Annual Energy Outlook 1995.

John H. Cymbalsky

1995-03-01T23:59:59.000Z

156

Biomass Energy Technology Module | Open Energy Information  

Open Energy Info (EERE)

Biomass Energy Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Biomass Energy Technology Module AgencyCompany Organization: World Bank Sector: Energy...

157

Module Encapsulation Materials, Processing and Testing (Presentation)  

DOE Green Energy (OSTI)

Study of PV module encapsulation materials, processing, and testing shows that overall module reliability is determined by all component materials and processing factors.

Pern, J.

2008-12-01T23:59:59.000Z

158

Optical modulation in a resonant tunneling relaxation oscillator  

E-Print Network (OSTI)

We report high speed optical modulation in a resonant tunneling relaxation oscillator consisting of a resonant tunneling diode (RTD) integrated with a unipolar optical waveguide and incorporated in a package with a coplanar waveguide transmission line. When appropriately biased, the RTD can provide wide-bandwidth electrical gain. For wavelengths near the material band-edge, small changes of the applied voltage give rise to large, high-speed electro-absorption modulation of the light. We have observed optical modulation at frequencies up to 14 GHz, associated with sub harmonic injection locking of the RTD oscillation at the fundamental mode of the coplanar transmission line, as well as generation of 33 ps optical pulses due to relaxation oscillation.

Figueiredo, J M L; Boyd, A R; Ironside, C N

1999-01-01T23:59:59.000Z

159

Oil and Gas Supply Module  

Gasoline and Diesel Fuel Update (EIA)

1 1 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Oil and Gas Supply Module The NEMS Oil and Gas Supply Module (OGSM) constitutes a comprehensive framework with which to analyze crude oil and natural gas exploration and development on a regional basis (Figure 8). The OGSM is organized into 4 submodules: Onshore Lower 48 Oil and Gas Supply Submodule, Offshore Oil and Gas Supply Submodule, Oil Shale Supply Submodule[1], and Alaska Oil and Gas Supply Submodule. A detailed description of the OGSM is provided in the EIA publication, Model Documentation Report: The Oil and Gas Supply Module (OGSM), DOE/EIA-M063(2011), (Washington, DC, 2011). The OGSM provides crude oil and natural gas short-term supply parameters to both the Natural Gas Transmission and Distribution Module and the Petroleum

160

Module Handbook Specialisation Biomass Energy  

E-Print Network (OSTI)

Target learning outcomes The module of Introduction and Basic concepts establishes the fundamental) Efficiency determination (I) Biofuels Management: prevention and protection against explosions Efficiency thermochemistry processes · Mass and energy balances · Efficiency calculation Target learning outcomes

Damm, Werner

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Multiple Layer Graphene Optical Modulator  

Scientists at Berkeley Lab have developed a tiny optical modulator based on graphene, potentially leading to significantly improved data transmission speeds in digital communications. The extremely strong interaction between light and relativistic ...

162

Module Handbook Specialisation Wind Energy  

E-Print Network (OSTI)

of wind energy External costs Future price trends 3. Environmental Issues Environmental benefits of WT and Externalities Clculation methods Current plant costs Wind energy prices The value Module Handbook Specialisation Wind Energy 2nd Semester for the Master Programme

Habel, Annegret

163

Fundamental & Applied Bioenergy | Clean Energy | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

a new generation of efficient bioenergy strategies that will reduce U.S. dependence on foreign oil and help curb carbon emissions. Fundamental and applied bioenergy research at...

164

Applied Control Strategies at a Cogeneration Plant.  

E-Print Network (OSTI)

?? The purpose of this paper is to demonstrate the effectiveness of classical strategies for dynamic control on authentic cogeneration processes. These strategies are applied (more)

Burns, Joseph William

2011-01-01T23:59:59.000Z

165

Applied Quantum Technology AQT | Open Energy Information  

Open Energy Info (EERE)

AQT Jump to: navigation, search Name Applied Quantum Technology (AQT) Place Santa Clara, California Zip 95054 Product California-based manufacturer of CIGS (copper indium gallium...

166

Solar cell module lamination process  

DOE Patents (OSTI)

A solar cell module lamination process using fluoropolymers to provide protection from adverse environmental conditions and thus enable more extended use of solar cells, particularly in space applications. A laminate of fluoropolymer material provides a hermetically sealed solar cell module structure that is flexible and very durable. The laminate is virtually chemically inert, highly transmissive in the visible spectrum, dimensionally stable at temperatures up to about 200.degree. C. highly abrasion resistant, and exhibits very little ultra-violet degradation.

Carey, Paul G. (Mountain View, CA); Thompson, Jesse B. (Brentwood, CA); Aceves, Randy C. (Tracy, CA)

2002-01-01T23:59:59.000Z

167

Compact magnetic energy storage module  

DOE Patents (OSTI)

A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module. 4 figures.

Prueitt, M.L.

1994-12-20T23:59:59.000Z

168

Compact magnetic energy storage module  

DOE Patents (OSTI)

A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module.

Prueitt, Melvin L. (Los Alamos, NM)

1994-01-01T23:59:59.000Z

169

Applied technology section. Monthly report, March 1994  

Science Conference Proceedings (OSTI)

This is a monthly report giving the details on research currently being conducted at the Savannah River Technology Center. The following are areas of the research, engineering modeling and simulation, applied statistics, applied physics,experimental thermal hydraulics,and packaging and transportation.

Buckner, M.R.

1994-04-20T23:59:59.000Z

170

DRAFT GUIDANCE Applying for Other Uses of  

E-Print Network (OSTI)

DRAFT GUIDANCE Applying for Other Uses of Phosphogypsum: Submitting a Complete Petition 40 CFR 61 Assignment 0-2 #12;Applying for Other Uses of Phosphogypsum: Submitting a Complete Petition Table of Contents phosphogypsum in stacks? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.4. What

171

Applied Materials Inc AMAT | Open Energy Information  

Open Energy Info (EERE)

Inc AMAT Inc AMAT Jump to: navigation, search Name Applied Materials Inc (AMAT) Place Santa Clara, California Zip 95052-8039 Sector Solar Product US-based manufacturer of equipment used in solar (silicon, thin-film, BIPV), semiconductor, and LCD markets. References Applied Materials Inc (AMAT)[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Applied Materials Inc (AMAT) is a company located in Santa Clara, California . References ↑ "Applied Materials Inc (AMAT)" Retrieved from "http://en.openei.org/w/index.php?title=Applied_Materials_Inc_AMAT&oldid=342244" Categories: Clean Energy Organizations Companies Organizations Stubs What links here Related changes

172

Applied Materials Wind Turbine | Open Energy Information  

Open Energy Info (EERE)

Wind Turbine Wind Turbine Jump to: navigation, search Name Applied Materials Wind Turbine Facility Applied Materials Sector Wind energy Facility Type Community Wind Facility Status In Service Owner Applied Materials Developer Applied Materials Energy Purchaser Applied Materials Location Gloucester MA Coordinates 42.62895426°, -70.65153122° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.62895426,"lon":-70.65153122,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

173

Modular Systems Biology applied to TGFbeta and DNA Damage Response Signaling following Low Dose Radiation  

NLE Websites -- All DOE Office Websites (Extended Search)

Modular Systems Biology applied to TGFbeta and DNA Damage Response Signaling following Modular Systems Biology applied to TGFbeta and DNA Damage Response Signaling following Low Dose Radiation Francis A. Cucinotta 1 , Yongfeng Li 2 , Minli Wang 2 , Claudio Carra 2 , Janice Pluth 3 , and Peter O'Neill 4 1 NASA Johnson Space Center, Houston, TX 2 U.S.R.A. Division of Life Sciences, Houston TX 3 Lawrence Berkeley National Laboratory, Berkeley CA 4 Oxford University, Oxford UK Abstract: Modular systems biology (MSB) describes the complexity of biological systems using well defined modules that represent distinct biological response pathways or sub-systems within pathways. We review mathematical concepts from control theory that can be used to identify and construct well defined modules for describing complex biological processes. The DNA damage response and TGFbeta/Smad signaling are two important response pathways following

174

Education of Risk Professionals Module 1  

Science Conference Proceedings (OSTI)

This report provides documentation for Module 1 in the Electric Power Research Institute EPRI) Education of Risk Professionals Probabilistic Risk Assessment PRA) training program. Module 1 is the first of six training modules in the Education of Risk Professionals series. Each module is one week in length, and the entire training program is typically scheduled over 10 months. Accompanying this report are the Microsoft PowerPoint slide presentations for Module 1, which contain speaker notes that offer de...

2009-12-23T23:59:59.000Z

175

Education of Risk Professionals Module 2  

Science Conference Proceedings (OSTI)

This report provides documentation for Module 2 in the Electric Power Research Institute (EPRI) Education of Risk Professionals Probabilistic Risk Assessment (PRA) training program. Module 2 is comprised of PRA 102, Systems Analysis and PRA 102A, Basic PRA Software. Module 2 is the second of six training modules in the Education of Risk Professionals series. Each module is typically one week in length. The entire training program is typically scheduled over the course of 10 months. The PowerPoint slide ...

2010-12-01T23:59:59.000Z

176

NEMS integrating module documentation report  

Science Conference Proceedings (OSTI)

The National Energy Modeling System (NEMS) is a computer modeling system that produces a general equilibrium solution for energy supply and demand in the US energy markets. The model achieves a supply and demand balance in the end-use demand regions, defined as the nine Census Divisions, by solving for the prices of each energy type such that the quantities producers are willing to supply equal the quantities consumers wish to consume. The system reflects market economics, industry structure, and energy policies and regulations that influence market behavior. The NEMS Integrating Module is the central integrating component of a complex modeling system. As such, a thorough understanding of its role in the modeling process can only be achieved by placing it in the proper context with respect to the other modules. To that end, this document provides an overview of the complete NEMS model, and includes brief descriptions of the modules with which the Integrating Module interacts. The emphasis and focus, however, is on the structure and function of the Integrating Module of NEMS.

Not Available

1993-12-14T23:59:59.000Z

177

Method and device for generating microwaves using a split cavity modulator  

DOE Patents (OSTI)

This invention consists of a compact device called the split cavity modulator whose self-generated oscillating electromagnetic field converts a steady particle beam into a modulated particle beam. The particle beam experiences both signs of the oscillating electric field during the transit through the split cavity modulator. The modulated particle beam can then be used to generate microwaves as that frequency and through a series of sequential extractors, high efficiency extraction of microwave power is enabled. The modulated beam and the microwave frequency can be varied by the placement of resistive wires at nodes of oscillation within the cavity. The short beam travel length through the cavity permit higher currents because both space charge and pinching limitations are reduced. The need for an applied magnetic field to control the beam has been eliminated.

Clark, M.C.; Coleman, P.D.; Marder, B.M.

1990-01-01T23:59:59.000Z

178

Method and split cavity oscillator/modulator to generate pulsed particle beams and electromagnetic fields  

DOE Patents (OSTI)

A compact device called the split cavity modulator whose self-generated oscillating electromagnetic field converts a steady particle beam into a modulated particle beam. The particle beam experiences both signs of the oscillating electric field during the transit through the split cavity modulator. The modulated particle beam can then be used to generate microwaves at that frequency and through the use of extractors, high efficiency extraction of microwave power is enabled. The modulated beam and the microwave frequency can be varied by the placement of resistive wires at nodes of oscillation within the cavity. The short beam travel length through the cavity permit higher currents because both space charge and pinching limitations are reduced. The need for an applied magnetic field to control the beam has been eliminated.

Clark, M.C.; Coleman, P.D.; Marder, B.M.

1993-08-10T23:59:59.000Z

179

Method and device for generating microwaves using a split cavity modulator  

DOE Patents (OSTI)

This invention consists of a compact device called the split cavity modulator whose self-generated oscillating electromagnetic field converts a steady particle beam into a modulated particle beam. The particle beam experiences both signs of the oscillating electric field during the transit through the split cavity modulator. The modulated particle beam can then be used to generate microwaves as that frequency and through a series of sequential extractors, high efficiency extraction of microwave power is enabled. The modulated beam and the microwave frequency can be varied by the placement of resistive wires at nodes of oscillation within the cavity. The short beam travel length through the cavity permit higher currents because both space charge and pinching limitations are reduced. The need for an applied magnetic field to control the beam has been eliminated.

Clark, M.C.; Coleman, P.D.; Marder, B.M.

1990-12-31T23:59:59.000Z

180

Method and split cavity oscillator/modulator to generate pulsed particle beams and electromagnetic fields  

DOE Patents (OSTI)

A compact device called the split cavity modulator whose self-generated oscillating electromagnetic field converts a steady particle beam into a modulated particle beam. The particle beam experiences both signs of the oscillating electric field during the transit through the split cavity modulator. The modulated particle beam can then be used to generate microwaves at that frequency and through the use of extractors, high efficiency extraction of microwave power is enabled. The modulated beam and the microwave frequency can be varied by the placement of resistive wires at nodes of oscillation within the cavity. The short beam travel length through the cavity permit higher currents because both space charge and pinching limitations are reduced. The need for an applied magnetic field to control the beam has been eliminated.

Clark, M. Collins (Albuquerque, NM); Coleman, P. Dale (Albuquerque, NM); Marder, Barry M. (Albuquerque, NM)

1993-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Applying System Engineering to Pharmaceutical Safety  

E-Print Network (OSTI)

While engineering techniques are used in the development of medical devices and have been applied to individual healthcare processes, such as the use of checklists in surgery and ICUs, the application of system engineering ...

Couturier, Matthieu

182

Applied Information Security, 1st edition  

Science Conference Proceedings (OSTI)

Applied Information Security guides readers through the installation and basic operation of IT Security software used in the industry today. Dos Commands; Password Auditors; Data Recovery & Secure Deletion; Packet Sniffer; Port Scanners; Vulnerability ...

Randy Boyle

2009-07-01T23:59:59.000Z

183

Baldrige FAQs: Applying for the Award  

Science Conference Proceedings (OSTI)

... often use their feedback reports in their strategic planning processes to focus ... How long does it take to apply for the ... How long will it take to do a self ...

2013-05-21T23:59:59.000Z

184

Applied Field Research Initiative Deep Vadose Zone  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Applied Field Research Initiative Applied Field Research Initiative Deep Vadose Zone Located on the Hanford Site in Richland, Washington, the Deep Vadose Zone Applied Field Research Initiative (DVZ AFRI) was established to protect water resources by addressing the challenge of preventing contamination in the deep vadose zone from reaching groundwater. Led by the Pacific Northwest National Laboratory, the Initiative is a collaborative effort that leverages Department of Energy (DOE) investments in basic science and applied research and the work of site contractors to address the complex deep vadose zone contamination challenges. Challenge Many vadose zone environments within the DOE complex consist of complex stratified layers of unconsolidated and water-unsaturated sediments that are, in many places, con-

185

Applied Virtual Intelligence in Oil & Gas Industry;  

E-Print Network (OSTI)

1 Applied Virtual Intelligence in Oil & Gas Industry; Past, Present, & Future Shahab D. Mohaghegh on a daily basis by almost everyone. Credit Card Fraud Detection Bank Loan Approval Bomb Sniffing Devices

Mohaghegh, Shahab

186

Computer Based Training: Engineering Technical Training Module - Centrifugal Pump Vibration 1.0  

Science Conference Proceedings (OSTI)

The Centrifugal Pump Vibration is a computer based training module that allows users to access training when desired and review it at their own pace. It provides graphics and limited interactive features to enhance learning. This module reviews the basic engineering principles used to calculate heat transfer and how to apply these principles to typical nuclear plant applications. The calculation of heat transfer in plant systems is an important element of many engineering calculations. Students should re...

2010-08-12T23:59:59.000Z

187

Programmable Multi-Chip Module  

DOE Patents (OSTI)

A multi-chip module comprising a low-temperature co-fired ceramic substrate having a first side on which are mounted active components and a second side on which are mounted passive components, wherein this segregation of components allows for hermetically sealing the active components with a cover while leaving accessible the passive components, and wherein the passive components are secured using a reflow soldering technique and are removable and replaceable so as to make the multi-chip module substantially programmable with regard to the passive components.

Kautz, David (Lenexa, KS); Morgenstern, Howard (Lee' s Summit, MO); Blazek, Roy J. (Overland Park, KS)

2004-11-16T23:59:59.000Z

188

Programmable Multi-Chip Module  

DOE Patents (OSTI)

A multi-chip module comprising a low-temperature co-fired ceramic substrate having a first side on which are mounted active components and a second side on which are mounted passive components, wherein this segregation of components allows for hermetically sealing the active components with a cover while leaving accessible the passive components, and wherein the passive components are secured using a reflow soldering technique and are removable and replaceable so as to make the multi-chip module substantially programmable with regard to the passive components.

Kautz, David (Lenexa, KS); Morgenstern, Howard (Lee' s Summit, MO); Blazek, Roy J. (Overland Park, KS)

2005-05-24T23:59:59.000Z

189

REGULATIONS ON PHOTOVOLTAIC MODULE DISPOSAL AND RECYCLING.  

Science Conference Proceedings (OSTI)

Environmental regulations can have a significant impact on product use, disposal, and recycling. This report summarizes the basic aspects of current federal, state and international regulations which apply to end-of-life photovoltaic (PV) modules and PV manufacturing scrap destined for disposal or recycling. It also discusses proposed regulations for electronics that may set the ground of what is to be expected in this area in the near future. In the US, several states have started programs to support the recycling of electronic equipment, and materials destined for recycling often are excepted from solid waste regulations during the collection, transfer, storage and processing stages. California regulations are described separately because they are different from those of most other states. International agreements on the movement of waste between different countries may pose barriers to cross-border shipments. Currently waste moves freely among country members of the Organization of Economic Cooperation and Development (OECD), and between the US and the four countries with which the US has bilateral agreements. However, it is expected, that the US will adopt the rules of the Basel Convention (an agreement which currently applies to 128 countries but not the US) and that the Convection's waste classification system will influence the current OECD waste-handling system. Some countries adopting the Basel Convention consider end-of-life electronics to be hazardous waste, whereas the OECD countries consider them to be non-hazardous. Also, waste management regulations potentially affecting electronics in Germany and Japan are mentioned in this report.

FTHENAKIS,V.

2001-01-29T23:59:59.000Z

190

Block IV solar cell module design and test specification for residential applications  

SciTech Connect

This specification provides near-term design, qualification and acceptance requirements for terrestrial solar cell modules suitable for incorporation in photovoltaic power sources (2 kW to 10 kW) applied to single family residential installations. Requirement levels and recommended design limits for selected performance criteria have been specified for modules intended principally for rooftop installations. Modules satisfying the requirements of this specification fall into one of two categories, residential panel or residential shingle, both meeting general performance requirements plus additional category peculiar constraints.

1978-11-01T23:59:59.000Z

191

Standard Test Methods for Electrical Performance of Nonconcentrator Terrestrial Photovoltaic Modules and Arrays Using Reference Cells  

E-Print Network (OSTI)

1.1 These test methods cover the electrical performance of photovoltaic modules and arrays under natural or simulated sunlight using a calibrated reference cell. 1.1.1 These test methods allow a reference module to be used instead of a reference cell provided the reference module has been calibrated using these test methods against a calibrated reference cell. 1.2 Measurements under a variety of conditions are allowed; results are reported under a select set of reporting conditions (RC) to facilitate comparison of results. 1.3 These test methods apply only to nonconcentrator terrestrial modules and arrays. 1.4 The performance parameters determined by these test methods apply only at the time of the test, and imply no past or future performance level. 1.5 These test methods apply to photovoltaic modules and arrays that do not contain series-connected photovoltaic multijunction devices; such module and arrays should be tested according to Test Methods E 2236. 1.6 The values stated in SI units are to be re...

American Society for Testing and Materials. Philadelphia

2008-01-01T23:59:59.000Z

192

Critical infrastructure security curriculum modules  

Science Conference Proceedings (OSTI)

Critical infrastructures have succumbed to the demands of greater connectivity. Although the scheme of connecting these critical equipment and devices to cyberspace has brought us tremendous convenience, it also enabled certain unimaginable risks and ... Keywords: SCADA, control systems, course modules, critical infrastructures, cybersecurity, programmable logic controllers, security, vulnerability

Guillermo A. Francia, III

2011-09-01T23:59:59.000Z

193

Shift register neutron coincidence module  

SciTech Connect

A neutron coincidence module was designed using multistage shift registers to produce the coincidence gates and a crystal controlled oscillator with variable clock outputs to change the gate lengths. The advantage of this system over the conventional, thermal-neutron coincidence gates is a decrease in deadtime by more than an order of magnitude. (auth)

Stephens, M.M.; Swansen, J.E.; East, L.V.

1975-11-01T23:59:59.000Z

194

Modulation Optimization under Energy Constraints  

E-Print Network (OSTI)

We consider radio applications where the nodes operate on batteries so that energy consumption must be minimized while satisfying given throughput and delay requirements. In this context, we analyze the best modulation strategy to minimize the total energy consumption required to send a given number of bits. The total energy consumption includes both the transmission energy and the circuit energy consumption. We show that for both MQAM and MFSK the transmission energy decreases with the product while the circuit energy consumption increases with , where is the modulation bandwidth and the transmission time. Thus, in short-range applications where the circuit energy consumption is nonnegligible compared with the transmission energy, the total energy consumption is minimized by using the maximum system bandwidth along with an optimized transmission time . We derive this optimal for MQAM and MFSK modulation in both AWGN channels and Rayleigh fading channels. Our optimization considers both delay and peak-power constraints. Numerical examples are given, where we exhibit up to 2 energy savings over modulation strategies that minimize the transmission energy alone.

Shuguang Cui Andrea; Andrea J. Goldsmith; Ahmad Bahai

2003-01-01T23:59:59.000Z

195

How to Apply | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How to Apply How to Apply How to Apply Awards are made through a formal process that has changed dramatically since 2011. So let us walk you through it step by step. "Innovation pays." - John Kao, Innovation Nation Submit a Letter of Intent On October 28, 2013, the U.S. Department of Energy (DOE) announced on the DOE SBIR website a preview version of the technical topics for which it will later accept funding applications. These topics will be found on the DOE's Funding Opportunity Announcements page. The EE SBIR page lists those topics that are cleantech (specific to EERE). We also recommend that you sign up for the EE-SBIR and DOE-SBIR mailing lists. The EE SBIR mailing list signup is at https://public.govdelivery.com/accounts/USEERE/subscriber/new?topic_id=USEERE_442.

196

Applied Field Research Initiative Attenuation Based Remedies  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PA00133 - March 2011 PA00133 - March 2011 Applied Field Research Initiative Attenuation Based Remedies in the Subsurface Located at the Savannah River Site in Aiken, South Carolina, the Attenuation-Based Remedies in the Subsurface Applied Field Research Initiative (ABRS AFRI) was established to develop the tools, approaches and technologies that will be required to address the technical challenges associated characteriza- tion, remediation and long-term monitoring of recalcitrant compounds in the subsurface at Department of Energy (DOE) Environmental Management (EM) sites. The ABRS AFRI site provides a unique setting for researchers in both applied and basic science fields. A wealth of subsurface data is available to support research activities and remedial decision making.

197

Applied Process Engineering Laboratory | Open Energy Information  

Open Energy Info (EERE)

Applied Process Engineering Laboratory Applied Process Engineering Laboratory Name Applied Process Engineering Laboratory Address 350 Hills Street, Suite #101 Place Richland, Washington Zip 99354 Region Pacific Northwest Area Coordinates 46.3389754°, -119.2716263° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":46.3389754,"lon":-119.2716263,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

198

Modeling International Relationships in Applied General Equilibrium  

Open Energy Info (EERE)

Modeling International Relationships in Applied General Equilibrium Modeling International Relationships in Applied General Equilibrium (MIRAGE) Jump to: navigation, search LEDSGP green logo.png FIND MORE DIA TOOLS This tool is part of the Development Impacts Assessment (DIA) Toolkit from the LEDS Global Partnership. Tool Summary LAUNCH TOOL Name: Modeling International Relationships in Applied General Equilibrium (MIRAGE) Agency/Company /Organization: International Food Policy Research Institute, Centre d'Etudes Prospectives et d'Informations Internationales (CEPII) Focus Area: Economic Development Topics: Co-benefits assessment, - Macroeconomic Resource Type: Software/modeling tools User Interface: Desktop Application Complexity/Ease of Use: Moderate Website: www.ifpri.org/book-5076/ourwork/program/mirage-model RelatedTo: Global Trade Analysis Project (GTAP) Data Base

199

Applied Ventures LLC | Open Energy Information  

Open Energy Info (EERE)

Applied Ventures LLC Applied Ventures LLC Name Applied Ventures LLC Address 3050 Bowers Avenue Place Santa Clara, California Zip 95054 Region Southern CA Area Product Venture capital. Number of employees 1-10 Phone number (408) 727-5555 Website http://www.appliedventures.com Coordinates 37.37751°, -121.978721° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.37751,"lon":-121.978721,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

200

Categorical Exclusion Determinations: Golden Field Office | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

14, 2011 14, 2011 CX-007422: Categorical Exclusion Determination Module-Integrated Power Converters Based on Universal Dock CX(s) Applied: A9, B3.6 Date: 12/14/2011 Location(s): Texas Offices(s): Golden Field Office December 14, 2011 CX-007413: Categorical Exclusion Determination Transforming Photovoltaic Installations Toward Discpatchable, Schedulable Energy Solutions CX(s) Applied: A9, B3.6 Date: 12/14/2011 Location(s): Oregon Offices(s): Golden Field Office December 13, 2011 CX-007418: Categorical Exclusion Determination Sidewalks to School CX(s) Applied: B1.13 Date: 12/13/2011 Location(s): South Carolina Offices(s): Golden Field Office December 13, 2011 CX-007426: Categorical Exclusion Determination Sharyland Independent School District CX(s) Applied: B5.16 Date: 12/13/2011

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

NREL Determines Better Testing Methods for Photovoltaic Module Durability (Fact Sheet), NREL Highlights, Research & Development  

DOE Green Energy (OSTI)

NREL discoveries will enable manufacturers to produce more robust photovoltaic modules. Over the past decade, some photovoltaic (PV) modules have experienced power losses because of the system voltage stress that modules experience in fielded arrays. This is partly because qualification tests and standards do not adequately evaluate the durability of modules that undergo the long-term effects of high voltage. Scientists at the National Renewable Energy Laboratory (NREL) tried various testing methods and stress levels to demonstrate module durability to system voltage potential-induced degradation (PID) mechanisms. The results of these accelerated tests, along with outdoor testing, were used to estimate the acceleration factors needed to more accurately evaluate the durability of modules to system voltage stress. NREL was able to determine stress factors, levels, and methods for testing based on the stresses experienced by modules in the field. These results, in combination with those in the literature, suggest that constant stress with humidity and system voltage is more damaging than stress applied intermittently or with periods of recovery comprising hot and dry conditions or alternating bias in between. NREL has determined some module constructions to be extremely durable to PID. These findings will help the manufacturers of PV materials and components produce more durable products that better satisfy their customers. NREL determined that there is rapid degradation of some PV modules under system voltage stress and evaluated degradation rates in the field to develop more accurate accelerated testing methods. PV module manufacturers will be better able to choose robust materials and durable designs and guarantee sturdier, longer-lasting products. As PV modules become more durable, and thus more efficient over the long term, the risks and the cost of PV power will be reduced.

Not Available

2011-11-01T23:59:59.000Z

202

Power System Equipment Module Test Project  

DOE Green Energy (OSTI)

The technology of electric power generation when applying the binary process to hydrothermal resources had not yet been demonstrated in the United States. Accordingly, on November 10, 1977, the Electric Power Research Institute and the Department of Energy, acting through the Lawrence Berkeley Laboratory, agreed to cofund the Power System Equipment Module Test Project. The Power System Equipment Module Test Project consisted of a field test program to accomplish the objectives listed below while heating hydrocarbon fluids to above their critical points, expanding these fluids, and subsequently, condensing them below their critical points: (1) Verify the performance of state-of-the-art heat exchangers in geothermal service; (2) Verify the heat exchangers' performance heating either selected pure light hydrocarbons or selected mixtures of light hydrocarbons in the vicinity of their respective critical pressures and temperatures; (3) Establish overall heat transfer coefficients that might be used for design of commercial-size geothermal power plants using the same geothermal brine and light hydrocarbon working fluids; (4) Perform and investigate the above under representative fluid operating conditions during which the production wells would be pumped. The project was accomplished by diverting approximately 200 gpm of the flow from one of Magma Power Company's geothermal wells in the East Mesa Geothermal Field. After the heat was removed from the geothermal brine flow, the cooled flow was returned to Magma Power Company and recombined with the main brine stream for disposal by reinjection. Approximately five thermal megawatts was transferred from geothermal brine to hydrocarbon working fluids in a closed system. This heat was removed from the working fluids in a condenser and subsequently rejected to the environment by a wet cooling tower. The thermodynamic performance of both the working fluids and the system components was measured during the test program to achieve the project's objectives.

Schilling, J.R.

1980-12-01T23:59:59.000Z

203

Overview of the PV Module Model in PVWatts (Presentation)  

DOE Green Energy (OSTI)

Overview of the PV module model. PVWatts module power estimates were compared with those using the Sandia model for three modules and data sets.

Marion, B.

2010-09-22T23:59:59.000Z

204

Mounting support for a photovoltaic module  

DOE Patents (OSTI)

A mounting support for a photovoltaic module is described. The mounting support includes a foundation having an integrated wire-way ledge portion. A photovoltaic module support mechanism is coupled with the foundation.

Brandt, Gregory Michael; Barsun, Stephan K.; Coleman, Nathaniel T.; Zhou, Yin

2013-03-26T23:59:59.000Z

205

Reliability Issues for Photovoltaic Modules (Presentation)  

DOE Green Energy (OSTI)

Si modules good in field; new designs need reliability testing. CdTe & CIGS modules sensitive to moisture; carefully seal. CPV in product development stage; benefits from expertise in other industries.

Kurtz, S.

2009-10-01T23:59:59.000Z

206

Energy Basics: Flat-Plate Photovoltaic Modules  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

PV module must have a high transmission in the wavelengths that can be used by the solar cells in the module. For example, for silicon solar cells, the top surface must have...

207

Applying Adaptive Evolutionary Algorithms to Hard Problems  

E-Print Network (OSTI)

Applying Adaptive Evolutionary Algorithms to Hard Problems J.I. van Hemert1 jvhemert into two distinct parts. The main theme is adaptive evolutionary algorithms. The rst part covers. The second part mainly consists of the development of a library. Its use is aimed at evolutionary algorithms

Emmerich, Michael

208

Uniform insulation applied-B ion diode  

DOE Patents (OSTI)

An applied-B field extraction ion diode has uniform insulation over an anode surface for increased efficiency. When the uniform insulation is accomplished with anode coils, and a charge-exchange foil is properly placed, and ions may be focused at a point on the z axis.

Seidel, D.B.; Slutz, S.A.

1986-04-11T23:59:59.000Z

209

Uniform insulation applied-B ion diode  

DOE Patents (OSTI)

An applied-B field extraction ion diode has uniform insulation over an anode surface for increased efficiency. When the uniform insulation is accomplished with anode coils, and a charge-exchange foil is properly placed, the ions may be focused at a point on the z axis.

Seidel, David B. (Albuquerque, NM); Slutz, Stephen A. (Albuquerque, NM)

1988-01-01T23:59:59.000Z

210

Interface module for transverse energy input to dye laser modules  

SciTech Connect

An interface module (10) for transverse energy input to dye laser modules is provided particularly for the purpose of delivering enhancing transverse energy beams (36) in the form of illumination bar (54) to the lasing zone (18) of a dye laser device, in particular to a dye laser amplifier (12). The preferred interface module (10) includes an optical fiber array (30) having a plurality of optical fibers (38) arrayed in a co-planar fashion with their distal ends (44) receiving coherent laser energy from an enhancing laser source (46), and their proximal ends (4) delivered into a relay structure (3). The proximal ends (42) of the optical fibers (38) are arrayed so as to be coplanar and to be aimed generally at a common point. The transverse energy beam array (36) delivered from the optical fiber array (30) is acted upon by an optical element array (34) to produce an illumination bar (54) which has a cross section in the form of a elongated rectangle at the position of the lasing window (18). The illumination bar (54) is selected to have substantially uniform intensity throughout.

English, Jr., Ronald E. (Tracy, CA); Johnson, Steve A. (Tracy, CA)

1994-01-01T23:59:59.000Z

211

Interface module for transverse energy input to dye laser modules  

DOE Patents (OSTI)

An interface module for transverse energy input to dye laser modules is provided particularly for the purpose of delivering enhancing transverse energy beams in the form of illumination bar to the lasing zone of a dye laser device, in particular to a dye laser amplifier. The preferred interface module includes an optical fiber array having a plurality of optical fibers arrayed in a co-planar fashion with their distal ends receiving coherent laser energy from an enhancing laser source, and their proximal ends delivered into a relay structure. The proximal ends of the optical fibers are arrayed so as to be coplanar and to be aimed generally at a common point. The transverse energy beam array delivered from the optical fiber array is acted upon by an optical element array to produce an illumination bar which has a cross section in the form of a elongated rectangle at the position of the lasing window. The illumination bar is selected to have substantially uniform intensity throughout. 5 figs.

English, R.E. Jr.; Johnson, S.A.

1994-10-11T23:59:59.000Z

212

Model Documentation Report: Macroeconomic Activity Module (MAM ...  

U.S. Energy Information Administration (EIA)

Model Documentation Report: Macroeconomic Activity Module (MAM) of the National Energy Modeling System April 2013 Independent Statistics & ...

213

High Frequency Power Modulation - TRIMET Smelters Provide ...  

Science Conference Proceedings (OSTI)

Presentation Title, High Frequency Power Modulation - TRIMET Smelters Provide Primary Control Power for Stabilizing the Frequency in the Electricity Grid.

214

Multisensor fusion-based gas detection module  

Science Conference Proceedings (OSTI)

This article develops a gas detection module for the intelligent home. The module uses eight gas sensors to detect the environment of the home and building. The gas sensors of the module have an NH3 sensor, an air pollution sensor, an alcohol ... Keywords: Intelligent home, Logical filter method, Multisensor fusion algorithms

Jr-Hung Guo; I. -Chao Chien; Kuo-Lan Su; Chia-Ju Wu

2011-06-01T23:59:59.000Z

215

Emittance growth from electron beam modulation  

SciTech Connect

In linac ring colliders like MeRHIC and eRHIC a modulation of the electron bunch can lead to a modulation of the beam beam tune shift and steering errors. These modulations can lead to emittance growth. This note presents simple formulas to estimate these effects which generalize some previous results.

Blaskiewicz, M.

2009-12-01T23:59:59.000Z

216

Automatic Layout Design for Power Module  

SciTech Connect

The layout of power modules is one of the key points in power module design, especially for high power densities, where couplings are increased. In this paper, along with the design example, an automatic design processes by using a genetic algorithm are presented. Some practical considerations and implementations are introduced in the optimization of module layout design.

Ning, Puqi [ORNL; Wang, Fei [ORNL; Ngo, Khai [Virginia Polytechnic Institute and State University (Virginia Tech)

2013-01-01T23:59:59.000Z

217

A Stability of LCLS Linac Modulators  

SciTech Connect

Information concerning to a stability of LCLS RF linac modulators is allocated in this paper. In general a 'pulse-to-pulse' modulator stability (and RF phase as well) is acceptable for the LCLS commission and FEL programs. Further modulator stability improvements are possible and approaches are discussed based on our experimental results.

Decker, F.-J.; Krasnykh, A.; Morris, B.; Nguyen, M.; /SLAC

2012-06-13T23:59:59.000Z

218

SiC Power Module  

NLE Websites -- All DOE Office Websites (Extended Search)

R&D 100 Entry R&D 100 Entry SiC Power Module 2 R&D 100 Entry SiC Power Module Submitting OrganizatiOn Sandia National Laboratories PO Box 5800, MS 1033 Albuquerque, NM 87185-1033 USA Stanley Atcitty Phone: 505-284-2701 Fax: 505-844-2890 satcitt@sandia.gov AFFIRMATION: I affirm that all information submitted as a part of, or supplemental to, this entry is a fair and accurate representation of this product. _____________________________________ Stanley Atcitty JOint Entry Arkansas Power Electronics International, Inc.; University of Arkansas; Rohm Co., LTD.; and the Department of Energy/ Energy Storage Program. 1. 1. Arkansas Power Electronics International, Inc. 535 W. Research Center Blvd. Fayetteville, AR 72701 USA Alexander B. Lostetter, President & CEO Phone: 479-443-5759

219

Module Encapsulant Diagnostic and Modeling  

DOE Green Energy (OSTI)

Encapsulant materials are used in photovoltaic devices for mechanical support, electrical isolation, and protection against corrosion. The ability of an encapsulant to protect against surface corrosion is related to its adhesional strength. The adhesion of candidate encapsulants under accelerated environmental stress was examined to determine what materials have the best hydrolytic stability and are more likely to reduce corrosion rates. Under environmental exposure, the ingress of water has been correlated with increased corrosion rates. The diffusivity of different encapsulants has been measured to determine how long it takes for water to enter a module. The high diffusivity of ethylene vinyl acetate indicates that, even with the use of an impermeable back-sheet, moisture from the sides will diffuse throughout the entire module. To significantly reduce moisture ingress requires a true hermetic seal, the use of an encapsulant loaded with desiccant, or the use of a very low diffusivity encapsulant.

Kempe, M.

2005-01-01T23:59:59.000Z

220

Gas separation membrane module assembly  

SciTech Connect

A gas-separation membrane module assembly and a gas-separation process using the assembly. The assembly includes a set of tubes, each containing gas-separation membranes, arranged within a housing. The housing contains a tube sheet that divides the space within the housing into two gas-tight spaces. A permeate collection system within the housing gathers permeate gas from the tubes for discharge from the housing.

Wynn, Nicholas P (Palo Alto, CA); Fulton, Donald A. (Fairfield, CA)

2009-03-31T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Title Page Applied and Environmental Microbiology 1  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied and Environmental Microbiology 1 Applied and Environmental Microbiology 1 2 Title Natural Competence in Thermoanaerobacter and Thermoanaerobacterium Species 3 Running Title Thermonanerobacter Natural Competence 4 5 Authors and Affiliations 6 A. Joe Shaw 1,2 , David A. Hogsett 1 , Lee R. Lynd 1,2,3 * 7 1 Mascoma Corporation, Lebanon, NH 03766 8 2 Thayer School of Engineering, Dartmouth College, Hanover, NH 03755 9 3 Department of Biological Sciences, Dartmouth College, Hanover, NH 03755 10 11 Corresponding Author 12 Lee R. Lynd 13 Thayer School of Engineering, Dartmouth College, Hanover, NH 03755 14 Phone: 603.646.2231 15 Email: lee.lynd@dartmouth.edu 16 17 18 19 20 21 22 23 Copyright © 2010, American Society for Microbiology and/or the Listed Authors/Institutions. All Rights Reserved.

222

Fundamental & Applied Bioenergy | Clean Energy | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Bioenergy Bioenergy SHARE Fundamental and Applied Bioenergy Steven Brown (left) and Shihui Yang have developed a microbial strain with an improved ability to convert wood products to biofuel as part of research within the DOE BioEnergy Science Center.Source: ORNL News article ORNL researchers are investigating the biological mechanisms underlying production of biofuels so that those mechanisms can be improved and used to develop a new generation of efficient bioenergy strategies that will reduce U.S. dependence on foreign oil and help curb carbon emissions. Fundamental and applied bioenergy research at ORNL includes studies conducted within the BioEnergy Science Center and the following research areas: Bioconversion Science and Technology Plant-Microbe Interfaces

223

Apply for Beam Time | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Apply for Beam Time Apply for Beam Time NEXT PROPOSAL DEADLINE: March 7, 2014 @ 11:59 PM (Chicago time) Submit Proposal » SEE ALSO: Calendar: deadlines, run & review dates Help Page: frequently asked questions, tips for success, common errors, blank forms, instructions Review Criteria Sectors Directory: check CAT websites for info about managed beam time The Run 2014-2 proposal submission deadline is 11:59 p.m. (Chicago time) March 7, 2014. The system will open to accept proposals beginning December 20, 2013. NEW USERS: to avoid delays and to make the most of your time on site, read Become a User. You must register as a user and receive a badge number before submitting a proposal. About the Beam Time Request Process All beam time at the APS must be requested each cycle through the web-based

224

Applying DSM evaluation results to utility planning  

SciTech Connect

This paper describes the results of a study to assess the application of DSM evaluation results to utility forecasting and planning. The paper has three objectives: (1) identify forecasting and planning applications of evaluation studies, (2) identify major obstacles and problems associated with applying evaluation results to forecasting and planning, and (3) suggest approaches to address the major problems. The paper summarizes results from interviews with utilities, regulators, and consultants to determine how the utility industry currently applies evaluation results in forecasting and planning. The paper also includes results from a detailed case study of Sacramento Municipal Utility District (SMUD) and Southern California Edison Company (SCE), two utilities with large DSM programs and active evaluation efforts.

Baxter, L.W.

1995-07-01T23:59:59.000Z

225

Method and system using power modulation and velocity modulation producing sputtered thin films with sub-angstrom thickness uniformity or custom thickness gradients  

DOE Patents (OSTI)

A method and system for determining a source flux modulation recipe for achieving a selected thickness profile of a film to be deposited (e.g., with highly uniform or highly accurate custom graded thickness) over a flat or curved substrate (such as concave or convex optics) by exposing the substrate to a vapor deposition source operated with time-varying flux distribution as a function of time. Preferably, the source is operated with time-varying power applied thereto during each sweep of the substrate to achieve the time-varying flux distribution as a function of time. Preferably, the method includes the steps of measuring the source flux distribution (using a test piece held stationary while exposed to the source with the source operated at each of a number of different applied power levels), calculating a set of predicted film thickness profiles, each film thickness profile assuming the measured flux distribution and a different one of a set of source flux modulation recipes, and determining from the predicted film thickness profiles a source flux modulation recipe which is adequate to achieve a predetermined thickness profile. Aspects of the invention include a computer-implemented method employing a graphical user interface to facilitate convenient selection of an optimal or nearly optimal source flux modulation recipe to achieve a desired thickness profile on a substrate. The method enables precise modulation of the deposition flux to which a substrate is exposed to provide a desired coating thickness distribution.

Montcalm, Claude (Livermore, CA); Folta, James Allen (Livermore, CA); Walton, Christopher Charles (Berkeley, CA)

2003-12-23T23:59:59.000Z

226

System Voltage Potential-Induced Degradation Mechanisms in PV Modules and Methods for Test: Preprint  

DOE Green Energy (OSTI)

Over the past decade, degradation and power loss have been observed in PV modules resulting from the stress exerted by system voltage bias. This is due in part to qualification tests and standards that do not adequately evaluate for the durability of modules to the long-term effects of high voltage bias experienced in fielded arrays. High voltage can lead to module degradation by multiple mechanisms. The extent of the voltage bias degradation is linked to the leakage current or coulombs passed from the silicon active layer through the encapsulant and glass to the grounded module frame, which can be experimentally determined; however, competing processes make the effect non-linear and history-dependent. Appropriate testing methods and stress levels are described that demonstrate module durability to system voltage potential-induced degradation (PID) mechanisms. This information, along with outdoor testing that is in progress, is used to estimate the acceleration factors needed to evaluate the durability of modules to system voltage stress. Na-rich precipitates are observed on the cell surface after stressing the module to induce PID in damp heat with negative bias applied to the active layer.

Hacke, P.; Terwilliger, K.; Smith, R.; Glick, S.; Pankow, J.; Kempe, M.; Kurtz, S.; Bennett, I.; Kloos, M.

2011-07-01T23:59:59.000Z

227

Applied Environmental Microbiology | VIMSS - Virtual Institute for  

NLE Websites -- All DOE Office Websites (Extended Search)

Collection of Soil Samples Collection of Soil Samples Identification of Natural Stressors Profiling of Microbial Population Field and Simulated Conceptual Model Facilities The Applied Environmental Microbiology (AEM) Core is the source of environmental data and samples that determine the stressors that will be studied, pro-vides the environments for growing the organisms to be tested, simulates stressed environments, and verifies the conceptual models to determine how these stress regulatory pathways control the biogeochemistry of contaminated sites. The specific goals of the AEM Core are to: Survey and map DOE sites contaminated by metals and radionuclides using chemical and molecular/ microbiological parameters to determine major microbial populations and potential stressors for Desulfovibrio vulgaris,

228

Statistical Uncertainty Analysis Applied to Criticality Calculation  

Science Conference Proceedings (OSTI)

In this paper, we present an uncertainty methodology based on a statistical approach, for assessing uncertainties in criticality prediction using monte carlo method due to uncertainties in the isotopic composition of the fuel. The methodology has been applied to criticality calculations with MCNP5 with additional stochastic input of the isotopic fuel composition. The stochastic input were generated using the latin hypercube sampling method based one the probability density function of each nuclide composition. The automatic passing of the stochastic input to the MCNP and the repeated criticality calculation is made possible by using a python script to link the MCNP and our latin hypercube sampling code.

Hartini, Entin; Andiwijayakusuma, Dinan; Susmikanti, Mike; Nursinta, A. W. [Centre for Nuclear Informatics Development, National Nuclear Energy Agency of Indonesia (Indonesia)

2010-06-22T23:59:59.000Z

229

LETTER doi:10.1038/nature10067 A graphene-based broadband optical modulator  

E-Print Network (OSTI)

of graphene is determined by the position of the Fermi level. By applying a drive voltage between the graphene/2. In reality, this transition was broadened owing to defects in the graphene, and shifted to higher voltage to a high-speed photodetector. Shown in Fig. 3 are the VD-dependent r.f. responses of the graphene modulator

Zhang, Xiang

230

Electric Modulation of Conduction and Optical Characteristics in Ca-doped BiFeO3 Films for Memory Device Applications  

E-Print Network (OSTI)

in Figure A.4, when an electric field is applied parallel toFigure A.4a). For anti-parallel electric field, the materialElectric Modulation of Conduction and Optical

Kim, Sang-Yong

2011-01-01T23:59:59.000Z

231

Analysis and Design of Smart PV Module  

E-Print Network (OSTI)

This thesis explores the design of a smart photovoltaic (PV) module- a PV module in which PV cells in close proximity are electrically grouped to form a pixel and are connected to dc-dc converter blocks which reside embedded in the back pane of the module. An auto-connected flyback converter topology processing less than full power is used to provide high gain and perform maximum power point tracking (MPPT). These dc-dc converters interface with cascaded H-bridge inverter modules operating on feed forward control for dc-link voltage ripple rejection. By means of feed forward control, a significant reduction in dc link capacitance is achieved by enduring higher dc link ripple voltages. The dc link electrolytic capacitors are replaced with film capacitors thus offering an improvement in the reliability of the smart PV module. The proposed configuration is capable of producing 120V/ 240V AC voltage. The PV module now becomes a smart AC module by virtue of embedded intelligence to selectively actuate the individual dc-dc converters and control the output AC voltages directly, thus becoming a true plug and power energy system. Such a concept is ideal for curved surfaces such as building integrated PV (BIPV) system applications where gradients of insolation and temperature cause not only variations from PV module-to-PV module but from group-to-group of cells within the module itself. A detailed analysis along with simulation and experimental results confirm the feasibility of the proposed system.

Mazumdar, Poornima

2012-12-01T23:59:59.000Z

232

The Applied Mathematics for Power Systems (AMPS)  

SciTech Connect

Increased deployment of new technologies, e.g., renewable generation and electric vehicles, is rapidly transforming electrical power networks by crossing previously distinct spatiotemporal scales and invalidating many traditional approaches for designing, analyzing, and operating power grids. This trend is expected to accelerate over the coming years, bringing the disruptive challenge of complexity, but also opportunities to deliver unprecedented efficiency and reliability. Our Applied Mathematics for Power Systems (AMPS) Center will discover, enable, and solve emerging mathematics challenges arising in power systems and, more generally, in complex engineered networks. We will develop foundational applied mathematics resulting in rigorous algorithms and simulation toolboxes for modern and future engineered networks. The AMPS Center deconstruction/reconstruction approach 'deconstructs' complex networks into sub-problems within non-separable spatiotemporal scales, a missing step in 20th century modeling of engineered networks. These sub-problems are addressed within the appropriate AMPS foundational pillar - complex systems, control theory, and optimization theory - and merged or 'reconstructed' at their boundaries into more general mathematical descriptions of complex engineered networks where important new questions are formulated and attacked. These two steps, iterated multiple times, will bridge the growing chasm between the legacy power grid and its future as a complex engineered network.

Chertkov, Michael [Los Alamos National Laboratory

2012-07-24T23:59:59.000Z

233

EG G Mound Applied Technologies payroll system  

SciTech Connect

EG G Mound Applied Technologies, Inc., manages and operates the Mound Facility, Miamisburg, Ohio, under a cost-plus-award-fee contract administered by the Department of Energy's Albuquerque Field Office. The contractor's Payroll Department is responsible for prompt payment in the proper amount to all persons entitled to be paid, in compliance with applicable laws, regulations, and legal decisions. The objective was to determine whether controls were in place to avoid erroneous payroll payments. EG G Mound Applied Technologies, Inc., did not have all the internal controls required by General Accounting Office Title 6, Pay, Leave, and Allowances.'' Specifically, they did not have computerized edits, separation of duties and responsibilities, and restricted access to payroll data files. This condition occurred because its managers were not aware of Title 6 requirements. As a result, the contractor could not assure the Department of Energy that payroll costs were processes accurately; and fraud, waste, or abuse of Department of Energy funds could go undetected. Our sample of 212 payroll transactions from a population of 66,000 in FY 1991 disclosed only two minor processing errors and no instances of fraud, waste or abuse.

Not Available

1992-02-07T23:59:59.000Z

234

Electrostatically actuatable light modulating device  

DOE Patents (OSTI)

The electrostatically actuatable light modulator utilizes an opaque substrate plate patterned with an array of aperture cells, the cells comprised of physically positionable dielectric shutters and electrostatic actuators. With incorporation of a light source and a viewing screen, a projection display system is effected. Inclusion of a color filter array aligned with the aperture cells accomplishes a color display. The system is realized in terms of a silicon based manufacturing technology allowing fabrication of a high resolution capability in a physically small device which with the utilization of included magnification optics allows both large and small projection displays.

Koehler, Dale R. (1332 Wagontrain Dr., Albuquerque, NM 87123)

1991-01-01T23:59:59.000Z

235

A Case Study of the Applied Learning Academy: Reconceptualized Quantum Design of Applied Learning  

E-Print Network (OSTI)

The purpose of this qualitative study was to examine the Applied Learning Academy (ALA) and allow the lessons learned from this public school to emerge from the narrative stories of past students, parents, teachers, administrators, and local business associates who have been directly involved and influenced by the applied learning teaching method. Accountability is critical for all public and charter schools. Districts have been trying to raise the standards with new programs and strategies in an effort to make learning experiences relevant to students? daily lives. Revisiting John Dewey?s philosophy from the progressive movement, project-based, service learning, community partnerships, and portfolio assessment helped to create the applied learning method. In the present study, a qualitative case study approach was utilized to identify successful factors, benefits, and drawbacks of applied learning in order to describe the transition of portfolio assessment, project-based learning, and community-based partnerships within the classroom and to understand the impact and misconceptions of applied learning as experienced through the Recognized Campus, ALA, a 6-8th public middle school within a large urban school district. Participant interviews, field observations, and historical records were collected which indicated that student centered project-based curriculum, small school size creating family relationships, community involvement with partnerships, service learning projects, and metacognitive development from portfolio assessments were the major factors that supported academic rigor and relevance because of the real educational applications in this applied learning middle school. Briefly defined, applied learning is when a problem is seen within the surrounding community, and the solution is generated by the students. This progressive 15-year impact of applied learning ultimately leads to the development of four applied learning schools despite the misconception that applied learning was a remedial or gifted program. Redefining applied learning for a better understanding developed a reconceptualized diagram borrowed from the quantum mechanics model. Reconceptualization expands the interpretation by increasing the intellectual flexibility. As the student becomes energized from the acquired knowledge of learning applicable skills through service learning, project-based curriculum, and portfolio assessment, the student?s academic growth should increase to a higher, educational ?energy level? supported by the critical, situated-learning, and feminist theories.

Gordon, Denise

2009-12-01T23:59:59.000Z

236

Binary module test. Final report  

DOE Green Energy (OSTI)

The objective of this project was to design and test a binary loop module representative of and scaleable to commercial size units. The design was based on state-of-the-art heat exchanger technology, and the purpose of the tests was to confirm performance of a supercritical boiling cycle using isobutane and a mixture of isobutane and isopentane as the secondary working fluid. The module was designed as one percent of a 50 MW unit. It was installed at Magma Power's East Mesa geothermal field and tested over a period of approximately 4 months. Most of the test runs were with isobutane but some data were collected for hydrocarbon mixtures. The results of the field tests are reported. In general these results indicate reasonably good heat balances and agreement with overall heat transfer coefficients calculated by current stream analysis methods and available fluid property data; however, measured pressure drops across the heat exchangers were 20 percent higher than estimated. System operation was stable under all conditions tested.

Schilling, J.R.; Colley, T.C.; Pundyk, J.

1980-12-01T23:59:59.000Z

237

Smart Fan Modules And System  

DOE Patents (OSTI)

A fan module including: two or more individual fans, each fan having an air movement means and a motor engaged with the air movement means for accelerating air entering each of the two or more individual fans; a temperature sensor for sensing a temperature associated with the two or more fans and for outputting a first signal corresponding to the temperature; rotational speed sensor for outputting a second signal corresponding to a rotational speed of each of the two or more fans; and a processor for receiving the first and second signals and controlling the two or more individual fans based on the first and second signals. A fan module including: two or more individual fans, each fan having an air movement means and a motor engaged with the air movement means for accelerating air entering each of the two or more individual fans; a temperature sensor for sensing a temperature associated with the two or more fans and for outputting a first signal corresponding to the temperature; rotational speed sensor for outputting a second signal corresponding to a rotational speed of each of the two or more fans; and a processor for receiving the first and second signals and controlling the two or more individual fans based on the first and second signals.

Cipolla, Thomas M. (Katonah, NY); Kaufman, Richard I. (Somers, NY); Mok, Lawrence S. (Brewster, NY)

2003-07-15T23:59:59.000Z

238

In-Line Thermoelectric Module  

DOE Patents (OSTI)

A thermoelectric module with a plurality of electricity generating units each having a first end and a second end, the units being arranged first end to second end along an-in-line axis. Each unit includes first and second elements each made of a thermoelectric material, an electrically conductive hot member arranged to heat one side of the first element, and an electrically conductive cold member arranged to cool another side of the first element and to cool one side of the second element. The hot member, the first element, the cold member and the second element are supported in a fixture, are electrically connected respectively to provide an electricity generating unit, and are arranged respectively in positions along the in-line axis. The individual components of each generating unit and the respective generating units are clamped in their in-line positions by a loading bolt at one end of the fixture and a stop wall at the other end of the fixture. The hot members may have a T-shape and the cold members an hourglass shape to facilitate heat transfer. The direction of heat transfer through the hot members may be perpendicular to the direction of heat transfer through the cold members, and both of these heat transfer directions maybe perpendicular to the direction-of current flow through the module.

Pento, Robert; Marks, James E.; Staffanson, Clifford D.

1998-07-28T23:59:59.000Z

239

In-line thermoelectric module  

DOE Patents (OSTI)

A thermoelectric module with a plurality of electricity generating units each having a first end and a second end, the units being arranged first end to second end along an in-line axis. Each unit includes first and second elements each made of a thermoelectric material, an electrically conductive hot member arranged to heat one side of the first element, and an electrically conductive cold member arranged to cool another side of the first element and to cool one side of the second element. The hot member, the first element, the cold member and the second element are supported in a fixture, are electrically connected respectively to provide an electricity generating unit, and are arranged respectively in positions along the in-line axis. The individual components of each generating unit and the respective generating units are clamped in their in-line positions by a loading bolt at one end of the fixture and a stop wall at the other end of the fixture. The hot members may have a T-shape and the cold members an hourglass shape to facilitate heat transfer. The direction of heat transfer through the hot members may be perpendicular to the direction of heat transfer through the cold members, and both of these heat transfer directions may be perpendicular to the direction of current flow through the module.

Pento, Robert (Algonquin, IL); Marks, James E. (Glenville, NY); Staffanson, Clifford D. (S. Glens Falls, NY)

2000-01-01T23:59:59.000Z

240

Definition: PV module | Open Energy Information  

Open Energy Info (EERE)

Definition Definition Edit with form History Facebook icon Twitter icon » Definition: PV module Jump to: navigation, search Dictionary.png PV module A unit comprised of several PV cells, and the principal unit of a PV array; it is intended to generate direct current power under un-concentrated sunlight.[1][2] View on Wikipedia Wikipedia Definition A solar panel is a set of solar photovoltaic modules electrically connected and mounted on a supporting structure. A photovoltaic module is a packaged, connected assembly of photovoltaic cells. The solar module can be used as a component of a larger photovoltaic system to generate and supply electricity in commercial and residential applications. Each module is rated by its DC output power under standard test conditions (STC), and

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Power module assemblies with staggered coolant channels  

DOE Patents (OSTI)

A manifold is provided for supporting a power module assembly with a plurality of power modules. The manifold includes a first manifold section. The first face of the first manifold section is configured to receive the first power module, and the second face of the first manifold section defines a first cavity with a first baseplate thermally coupled to the first power module. The first face of the second manifold section is configured to receive the second power module, and the second face of the second manifold section defines a second cavity with a second baseplate thermally coupled to the second power module. The second face of the first manifold section and the second face of the second manifold section are coupled together such that the first cavity and the second cavity form a coolant channel. The first cavity is at least partially staggered with respect to second cavity.

Herron, Nicholas Hayden; Mann, Brooks S; Korich, Mark D

2013-07-16T23:59:59.000Z

242

Applied Energy Management | Open Energy Information  

Open Energy Info (EERE)

Management Management Jump to: navigation, search Name Applied Energy Management Place Huntersville, North Carolina Zip 28078 Sector Efficiency, Renewable Energy Product North Carolina-based, energy efficiency and renewable energy service and construction company. Coordinates 35.409853°, -80.842716° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":35.409853,"lon":-80.842716,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

243

How to Apply for ENERGY STAR® Certification  

NLE Websites -- All DOE Office Websites (Extended Search)

ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü "How To" Series How to Apply for ENERGY STAR ® Certification Commercial buildings that earn EPA's ENERGY STAR certification perform in the top 25 percent of similar buildings nationwide, as verified by a Licensed Professional (a Professional Engineer or a Registered Architect). ENERGY STAR certified buildings use an average of 35 percent less energy and are responsible for 35 percent fewer greenhouse gas emissions than average buildings. To qualify for the ENERGY STAR, a property must achieve an ENERGY STAR score of 75 or higher on EPA's 1 - 100 scale, which compares a property's energy performance to

244

Navigating without vision: Basic and applied research  

E-Print Network (OSTI)

ABSTRACT: We describe some of the results of our program of basic and applied research on navigating without vision. One basic research topic that we have studied extensively is path integration, a form of navigation in which perceived self-motion is integrated over time to obtain an estimate of current posilion and orientation. In experiments on pathway completion, one test of path integration ability, we have found that subjects who are passively guided over the outbound path without vision exhibit significant errors when attempting to return to the origin but are nevertheless sensitive to turns and segment lengths in the stimulus path. We have also found no major differences in path inlegration ability among blirid and sighted populations. A model we havc developed that attributes errors in path integration to errors in encoding the stimulus path is a good beginning toward understanding path integration performance. In otber research on path integration, in which optic flow information was manipulated in addition to the proprioceptive and vestibular information of nonvisual locomotion, we havc found that optic flow is a weak input to the path integration process. In other basic research, our studies of auditory distance perception in outdoor environments show systematic underestimation oC sound source distance. Our applied research has been concerned with developing and evaluating a navigation system for the visually impaired that uses three recent technologies: the Global Positioning System, Geographic Information Systems, and virtual acouslics. Our work shows that there is considerable promise of these three technologies in allowing visually impaired individuals to navigate and learn about unfamiliar environments without the assistance of human guides. (Optoni Vis Sci 2001;78:282-289)

Jack M. Loomis; Roberta L. Klatzky; Reginald G. Golledge

2001-01-01T23:59:59.000Z

245

Enhancing the Electrooptic Effect Using Modulation Instability  

E-Print Network (OSTI)

As electronic operating frequencies increase toward the terahertz regime, new electrooptic modulators capable of low-voltage high-frequency operation must be developed to provide the necessary optical interconnects. This letter presents a new concept that exploits modulation instability to enhance the intrinsically weak electrooptic effect, \\chi^(2). Simulations demonstrate more than 50 times enhancement of electrooptic effect at millimeter wave frequencies leading to a substantial reduction in the required modulation voltage.

DeVore, Peter T S; Jalali, Bahram

2013-01-01T23:59:59.000Z

246

Residential Sector Demand Module 1998, Model Documentation  

Reports and Publications (EIA)

This is the fourth edition of the Model Documentation Report: Residential Sector DemandModule of the National Energy Modeling System (NEMS). It reflects changes made to themodule over the past year for the Annual Energy Outlook 1998. Since last year, severalnew end-use services were added to the module, including: Clothes washers,dishwashers, furnace fans, color televisions, and personal computers. Also, as with allNEMS modules, the forecast horizon has been extended to the year 2020.

John H. Cymbalsky

1998-01-01T23:59:59.000Z

247

Photovoltaic Energy Technology Module | Open Energy Information  

Open Energy Info (EERE)

Photovoltaic Energy Technology Module Photovoltaic Energy Technology Module Jump to: navigation, search Tool Summary Name: Photovoltaic Energy Technology Module Agency/Company /Organization: World Bank Sector: Energy Focus Area: Renewable Energy, Solar Topics: Technology characterizations Website: web.worldbank.org/WBSITE/EXTERNAL/TOPICS/EXTENERGY2/EXTRENENERGYTK/0,, References: Photovoltaic Energy Technology Module[1] Resources Portable Solar Photovoltaic Lanterns: Performance and Certification Specification, and Type Approval, ESMAP TECHNICAL PAPER 078 Testing of Storage Batteries used in Stand Alone Photovoltaic Power Systems, Test procedures and examples of test results Technical Specifications for Solar Home Systems (SHS), Rural Electrification and Renewable Energy Development (PV Component) Project

248

Optical sensing based on wavelength modulation spectroscopy  

DOE Patents (OSTI)

Techniques, apparatus and systems for using Wavelength Modulation Spectroscopy measurements to optically monitor gas media such as gases in gas combustion chambers.

Buckley, Steven G. (Redmond, WA); Gharavi, Mohammadreza (Tehran, IR); Borchers; Marco (Berlin, DE)

2011-06-28T23:59:59.000Z

249

Stably free modules over smooth affine threefolds.  

E-Print Network (OSTI)

We prove that the stably free modules over a smooth affine threefold over an algebraically closed field of characteristic different from 2 are free.

Jean Fasel.; no 1; 33--49

250

Stably free modules over smooth affine threefolds  

E-Print Network (OSTI)

We prove that the stably free modules over a smooth affine threefold over an algebraically closed field of characteristic different from 2 are free.

Fasel, Jean

2009-01-01T23:59:59.000Z

251

Petroleum Market Module - Energy Information Administration  

U.S. Energy Information Administration (EIA)

U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 137 Petroleum Market Module Table 11.2. Year-round gasoline ...

252

Reflective Coherent Spatial Light Modulator (RCSLM)  

Reflective Coherent Spatial Light Modulator (RCSLM) Note: The technology described above is an early stage opportunity. Licensing rights to this intellectual property may

253

Figure F2. Electricity market module regions  

U.S. Energy Information Administration (EIA)

U.S. Energy Information Administration Annual Energy Outlook 2013 227 Regional maps Figure F2. Electricity market module regions Source: U.S. Energy Information ...

254

Stably Free Modules Over the Klein Bottle.  

E-Print Network (OSTI)

??This paper is concerned with constructing countably many, non-free stably free modules for the Klein bottle group. The work is based on the papers Stably (more)

Misseldine, Andrew

2010-01-01T23:59:59.000Z

255

THE EFFECT OF ACOUSTIC MODULATION ON SPRAY ...  

Science Conference Proceedings (OSTI)

... that at full load in liquid injection systems, extra energy or perturbation is ... The acoustic modulation is generated by a piezoelectric crystal driven by a ...

256

Village Hydro Technology Module | Open Energy Information  

Open Energy Info (EERE)

Module AgencyCompany Organization: World Bank Sector: Energy Focus Area: Renewable Energy, Hydro Topics: Technology characterizations Website: web.worldbank.orgWBSITE...

257

Innovative Approaches to Low Cost Module Manufacturing of String Ribbon Si PV Modules: First Annual Report, 27 September 2002--31 March 2003  

DOE Green Energy (OSTI)

This report describes Evergreen Solar, Inc., String Ribbon Si PV technology resulting in an advanced generation of crystalline silicon PV module manufacturing technology applied to a virtually continuous, fully integrated manufacturing line. General objectives for this first year (or Phase I) are listed here, followed by the principal accomplishments for each of these objectives: (1) scale-up of a production-worthy method for doping feedstock; (2) development of a multiple-ribbon growth system (Project Gemini); (3) development of wrap-around contacts for making monolithic modules; (4) accelerated testing of small-size (25 W) monolithic modules; (5) development of an in-line production machine to form solar cell contacts using Evergreen's unique contact printing technology.

Hanoka, J. I.

2004-05-01T23:59:59.000Z

258

PRA Fundamentals Computer Based Training Module 2.1  

Science Conference Proceedings (OSTI)

This product is a computer based training (CBT) module on Probabilistic Risk Assessment (Module 2 PRA Fundamentals). This product is a computer based training module on Probabilistic Risk Assessment (PRA CBT Module 2 - PRA Fundamentals). The PRA CBT is the second module and it titled PRA Fundamentals. This module is designed to provide a high level intriduction to the fundamentals of PRAs for nuclear power plants. It is the second module in the series. WindowsXP/Vista/Windows 7.

2010-11-30T23:59:59.000Z

259

201/span>3 Short Course Applied Fundamentals in Interfacial Phenomena  

Science Conference Proceedings (OSTI)

Applied Fundamentals in Interfacial Phenomena Short Course held at the 104th AOCS Annual Meeting and Expo. 201/span>3 Short Course Applied Fundamentals in Interfacial Phenomena Applied Fundamentals in Interfacial Phenomena Saturday

260

SRTC criticality safety technical review: Nuclear criticality safety evaluation 94-02, uranium solidification facility pencil tank module spacing  

SciTech Connect

Review of NMP-NCS-94-0087, ``Nuclear Criticality Safety Evaluation 94-02: Uranium Solidification Facility Pencil Tank Module Spacing (U), April 18, 1994,`` was requested of the SRTC Applied Physics Group. The NCSE is a criticality assessment to show that the USF process module spacing, as given in Non-Conformance Report SHM-0045, remains safe for operation. The NCSE under review concludes that the module spacing as given in Non-Conformance Report SHM-0045 remains in a critically safe configuration for all normal and single credible abnormal conditions. After a thorough review of the NCSE, this reviewer agrees with that conclusion.

Rathbun, R. [Westinghouse Savannah River Co., Aiken, SC (United States)

1994-04-26T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Remediation of Mercury and Industrial Contaminants Applied Field...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Remediation of Mercury and Industrial Contaminants Applied Field Research Initiative (RoMIC-AFRI) Remediation of Mercury and Industrial Contaminants Applied Field Research...

262

Computational Advances in Applied Energy | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Advances in Applied Energy Computational Advances in Applied Energy Friedmann-LLNL-SEAB.10.11.pdf More Documents & Publications Director's Perspective by George Miller...

263

Attenuation-Based Remedies in the Subsurface Applied Field Research...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Subsurface Applied Field Research Initiative (ABRS AFRI) Located at the Savannah River Site in Aiken, South Carolina, the Attenuation-Based Remedies in the Subsurface Applied...

264

Applying Climate Information for Adaptation Decision-Making:...  

Open Energy Info (EERE)

Applying Climate Information for Adaptation Decision-Making: A Guidance and Resource Document Jump to: navigation, search Tool Summary Name: Applying Climate Information for...

265

Applying physics, teamwork to fusion energy science | Princeton...  

NLE Websites -- All DOE Office Websites (Extended Search)

Applying physics, teamwork to fusion energy science American Fusion News Category: Massachusetts Institute of Technology (MIT) Link: Applying physics, teamwork to fusion energy...

266

Standard Test Method for Electrical Performance of Concentrator Terrestrial Photovoltaic Modules and Systems Under Natural Sunlight  

E-Print Network (OSTI)

1.1 This test method covers the determination of the electrical performance of photovoltaic concentrator modules and systems under natural sunlight using a normal incidence pyrheliometer. 1.2 The test method is limited to module assemblies and systems where the geometric concentration ratio specified by the manufacturer is greater than 5. 1.3 This test method applies to concentrators that use passive cooling where the cell temperature is related to the air temperature. 1.4 Measurements under a variety of conditions are allowed; results are reported under a select set of concentrator reporting conditions to facilitate comparison of results. 1.5 This test method applies only to concentrator terrestrial modules and systems. 1.6 This test method assumes that the module or system electrical performance characteristics do not change during the period of test. 1.7 The performance rating determined by this test method applies only at the period of the test, and implies no past or future performance level. 1.8...

American Society for Testing and Materials. Philadelphia

2009-01-01T23:59:59.000Z

267

CONDITIONING AND PROTECTION CIRCUITRY FOR EXTERNAL MODULATION OF A PREPROGRAMMED GYROTRON CATHODE VOLTAGE COMMAND WAVEFORM  

Science Conference Proceedings (OSTI)

OAK-B135 The modulating voltages applied to the DIII-D gyrotrons are controlled by reference signals which are synthesized by arbitrary waveform generators.These generators allow ECH operators to pre-program reference waveforms consisting of ramps, flat tops, and various modulation shapes. This capability is independent of the DIII-D central timing and waveform facilities, which provides the ECH operators operational flexibility. The waveform generators include an amplitude modulation input, providing a means to control the pre-programmed waveform externally. This input is being used to allow the DIII-D plasma control system (PCS) to control gyrotron power in response top selected feedback signals. As the PCS control signal could potentially modulate the gyrotrons beyond operational limits or otherwise in a manner leading to recalcitrant rf generation, the control signal is conditioned so that its effect upon the ECH pre-programmed reference waveform is limited by conditions set by the ECH operators. The design of the circuitry which restricts the range over which the PCS control signal may modulate the reference waveform will be discussed. Test and DIII-D experimental results demonstrating the utility and effectiveness of gyrotron power modulated by the PCS will be presented.

PONCE,D; FERRON,J.R; LEGG,R.A

2003-10-01T23:59:59.000Z

268

Development Status of The ILC Marx Modulator  

SciTech Connect

The ILC Marx Modulator is under development as a lower cost alternative to the 'Baseline Conceptual Design' (BCD) klystron modulator. Construction of a prototype Marx is complete and testing is underway at SLAC. The Marx employs solid state elements, IGBTs and diodes, to control the charge, discharge and isolation of the modules. The prototype is based on a stack of sixteen modules, each initially charged to {approx}11 kV, which are arranged in a Marx topology. Initially, eleven modules combine to produce the 120 kV output pulse. The remaining modules are switched in after appropriate delays to compensate for the voltage droop that results from the discharge of the energy storage capacitors. Additional elements will further regulate the output voltage to {+-}0.5%. The Marx presents several advantages over the conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at these parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. This paper outlines the current developmental status of the prototype Marx. It presents a detailed electrical and mechanical description of the modulator and operational test results. It will discuss electrical efficiency measurements, fault testing, and output voltage regulation.

Nguyen, M; Beukers, T.; Burkhart, C.; Larsen, R.; Olsen, J.; Tang, T.; /SLAC

2010-06-07T23:59:59.000Z

269

Testing Protocol for Module Encapsulant Creep (Presentation)  

DOE Green Energy (OSTI)

Recently there has been an interest in the use of thermoplastic encapsulant materials in photovoltaic modules to replace chemically crosslinked materials, e.g., ethylene-vinyl acetate. The related motivations include the desire to: reduce lamination time or temperature; use less moisture-permeable materials; or use materials with better corrosion characteristics. However, the use of any thermoplastic material in a high-temperature environment raises safety and performance concerns, as the standardized tests currently do not expose the modules to temperatures in excess of 85C, yet modules may experience temperatures above 100C in operation. Here we constructed eight pairs of crystalline-silicon modules and eight pairs of glass/encapsulation/glass mock modules using different encapsulation materials of which only two were designed to chemically crosslink. One module set was exposed outdoors with insulation on the back side in Arizona in the summer, and an identical set was exposed in environmental chambers. High precision creep measurements and performance measurements indicate that despite many of these polymeric materials being in the melt state at some of the highest outdoor temperatures achievable, very little creep was seen because of their high viscosity, temperature heterogeneity across the modules, and in the case of the crystalline-silicon modules, the physical restraint of the backsheet. These findings have very important implications for the development of IEC and UL qualification and safety standards, and in regards to the necessary level of cure during the processing of crosslinking encapsulants.

Kempe, M. D.; Miller, D. C.; Wohlgemuth, J. H.; Kurtz, S. R.; Moseley, J. M.; Shah, Q.; Tamizhmani, G.; Sakurai, K.; Inoue, M.; Doi, T.; Masuda, A.

2012-02-01T23:59:59.000Z

270

Module Handbook Core Univ. of Oldenburg  

E-Print Network (OSTI)

, DMS (strain gauge?) Test bridge, Fatigue Extrapolation · Wind Diesel Systeme in kleinen Inselnetzen/EUREC Course 2008/2009 #12;EUREC Core Courses at University of Oldenburg, 1st Semester Wind Energy Module Module Description: Wind Energy Field: Core Oldenburg Courses: Wind Energy Wind Energy

Habel, Annegret

271

Modulation instability in RF MEMS devices  

Science Conference Proceedings (OSTI)

Modulation instability generated by mechanical frequencies in RF MEMS switches is predicted and its potential contribution to the RF signal degradation is discussed. In particular, evaluations have been performed for double clamped configurations in ... Keywords: Modulation instability, Nonlinear Schrodinger equation, Power handling, RF MEMS

Romolo Marcelli; Giancarlo Bartolucci; Giorgio Angelis; Andrea Lucibello; Emanuela Proietti

2012-04-01T23:59:59.000Z

272

Development Status of the ILC Marx Modulator  

DOE Green Energy (OSTI)

The ILC Marx Modulator is under development as a lower cost alternative to the 'Baseline Conceptual Design' (BCD) klystron modulator. Construction of a prototype Marx is complete and testing is underway at SLAC. The Marx employs solid state elements, IGBTs and diodes, to control the charge, discharge and isolation of the modules. The prototype is based on a stack of sixteen modules, each initially charged to {approx}11 kV, which are arranged in a Marx topology. Initially, eleven modules combine to produce the 120 kV output pulse. The remaining modules are switched in after appropriate delays to compensate for the voltage droop that results from the discharge of the energy storage capacitors. Additional elements will further regulate the output voltage to {+-} 0.5%. The Marx presents several advantages over the conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at these parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. This paper outlines the current developmental status of the prototype Marx. It presents a detailed electrical and mechanical description of the modulator and operational test results. It will discuss electrical efficiency measurements, fault testing, and output voltage regulation.

Nguyen, M.; Beukers, T.; Burkhart, C.; Larsen, R.; Olsen, J.; Tang, T.; /SLAC

2008-06-16T23:59:59.000Z

273

A type system for recursive modules  

Science Conference Proceedings (OSTI)

There has been much work in recent years on extending ML with recursive modules. One of the most difficult problems in the development of such an extension is the double vision problem, which concerns the interaction of recursion and data abstraction. ... Keywords: abstract data types, modules, recursion, type systems

Derek Dreyer

2007-10-01T23:59:59.000Z

274

Identification coding schemes for modulated reflectance systems  

DOE Patents (OSTI)

An identifying coding apparatus employing modulated reflectance technology involving a base station emitting a RF signal, with a tag, located remotely from the base station, and containing at least one antenna and predetermined other passive circuit components, receiving the RF signal and reflecting back to the base station a modulated signal indicative of characteristics related to the tag.

Coates, Don M. (Santa Fe, NM); Briles, Scott D. (Los Alamos, NM); Neagley, Daniel L. (Albuquerque, NM); Platts, David (Santa Fe, NM); Clark, David D. (Santa Fe, NM)

2006-08-22T23:59:59.000Z

275

Transportation Sector Module 1997, Model Documentation  

Reports and Publications (EIA)

Over the past year, several modifications have been made to the NEMS Transportation Model,incorporating greater levels of detail and analysis in modules previously represented in the aggregate or under a profusion of simplifying assumptions. This document is intended to amend those sections of the Model Documentation Report (MDR) which describe these superseded modules.

John Maples

1997-02-01T23:59:59.000Z

276

Analysis of FPGA/FPIC switch modules  

Science Conference Proceedings (OSTI)

Switch modules are the most important component of the routing resources in FPGAs/FPICs. Previous works have shown that switch modules with higher routability result in better area performance for practical applications. We consider in this paper an ... Keywords: Computer-aided design of VLSI, FPGA, FPIC, layout, synthesis

Yao-Wen Chang; Kai Zhu; Guang-Ming Wu; D. F. Wong; C. K. Wong

2003-01-01T23:59:59.000Z

277

Semidualizing modules Sean Sather-Wagstaff  

E-Print Network (OSTI)

, (R, m) is a Cohen-Macaulay local ring with canonical module = R. Definition. A finitely generated R-module C is semidualizing if (a) The natural homothety homomorphism R C : R HomR(C, C) is an isomorphism, and (b) Exti R(C, C) = 0 for each i = 0. Notation. S0(R) is the set of isomorphism classes

Sather-Wagstaff, Sean

278

Advanced Indoor Module Light-Soaking Facility  

DOE Green Energy (OSTI)

An overview of the accelerated, indoor light-soaking test station is presented in this paper, along with data obtained for six modules that underwent exposure. The station comprises a climate-controlled chamber equipped with a solar simulator that allows 1-sun light intensity exposure. Concurrently, we monitor the electrical characteristics of multiple PV modules and exercise active control over their electrical bias using programmable electronic loads, interfaced to a data acquisition system that acquires power-tracking and current-voltage data. This capability allows us to the test different bias conditions and to cyclically alternate between them. Additionally, we can vary the light intensity and module temperatures to garner realistic temperature coefficients of module performance. Data obtained on cadmium telluride (CdTe) and amorphous silicon (a-Si) modules are presented.

del Cueto, J. A.; Osterwald, C.; Pruett, J.

2005-01-01T23:59:59.000Z

279

Ion transport membrane module and vessel system  

DOE Patents (OSTI)

An ion transport membrane system comprising (a) a pressure vessel having an interior, an exterior, an inlet, and an outlet; (b) a plurality of planar ion transport membrane modules disposed in the interior of the pressure vessel and arranged in series, each membrane module comprising mixed metal oxide ceramic material and having an interior region and an exterior region, wherein any inlet and any outlet of the pressure vessel are in flow communication with exterior regions of the membrane modules; and (c) one or more gas manifolds in flow communication with interior regions of the membrane modules and with the exterior of the pressure vessel. The ion transport membrane system may be utilized in a gas separation device to recover oxygen from an oxygen-containing gas or as an oxidation reactor to oxidize compounds in a feed gas stream by oxygen permeated through the mixed metal oxide ceramic material of the membrane modules.

Stein, VanEric Edward (Allentown, PA); Carolan, Michael Francis (Allentown, PA); Chen, Christopher M. (Allentown, PA); Armstrong, Phillip Andrew (Orefield, PA); Wahle, Harold W. (North Canton, OH); Ohrn, Theodore R. (Alliance, OH); Kneidel, Kurt E. (Alliance, OH); Rackers, Keith Gerard (Louisville, OH); Blake, James Erik (Uniontown, OH); Nataraj, Shankar (Allentown, PA); Van Doorn, Rene Hendrik Elias (Obersulm-Willsbach, DE); Wilson, Merrill Anderson (West Jordan, UT)

2012-02-14T23:59:59.000Z

280

Ion transport membrane module and vessel system  

DOE Patents (OSTI)

An ion transport membrane system comprising (a) a pressure vessel having an interior, an exterior, an inlet, and an outlet; (b) a plurality of planar ion transport membrane modules disposed in the interior of the pressure vessel and arranged in series, each membrane module comprising mixed metal oxide ceramic material and having an interior region and an exterior region, wherein any inlet and any outlet of the pressure vessel are in flow communication with exterior regions of the membrane modules; and (c) one or more gas manifolds in flow communication with interior regions of the membrane modules and with the exterior of the pressure vessel.The ion transport membrane system may be utilized in a gas separation device to recover oxygen from an oxygen-containing gas or as an oxidation reactor to oxidize compounds in a feed gas stream by oxygen permeated through the mixed metal oxide ceramic material of the membrane modules.

Stein, VanEric Edward (Allentown, PA); Carolan, Michael Francis (Allentown, PA); Chen, Christopher M. (Allentown, PA); Armstrong, Phillip Andrew (Orefield, PA); Wahle, Harold W. (North Canton, OH); Ohrn, Theodore R. (Alliance, OH); Kneidel, Kurt E. (Alliance, OH); Rackers, Keith Gerard (Louisville, OH); Blake, James Erik (Uniontown, OH); Nataraj, Shankar (Allentown, PA); van Doorn, Rene Hendrik Elias (Obersulm-Willsbach, DE); Wilson, Merrill Anderson (West Jordan, UT)

2008-02-26T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Flat-Plate Photovoltaic Modules | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Modules Flat-Plate Photovoltaic Modules August 20, 2013 - 4:25pm Addthis Flat-plate photovoltaic (PV) modules are made of several components, including the front surface materials,...

282

PSCAD Modules Representing PV Generator  

SciTech Connect

Photovoltaic power plants (PVPs) have been growing in size, and the installation time is very short. With the cost of photovoltaic (PV) panels dropping in recent years, it can be predicted that in the next 10 years the contribution of PVPs to the total number of renewable energy power plants will grow significantly. In this project, the National Renewable Energy Laboratory (NREL) developed a dynamic modeling of the modules to be used as building blocks to develop simulation models of single PV arrays, expanded to include Maximum Power Point Tracker (MPPT), expanded to include PV inverter, or expanded to cover an entire PVP. The focus of the investigation and complexity of the simulation determines the components that must be included in the simulation. The development of the PV inverter was covered in detail, including the control diagrams. Both the current-regulated voltage source inverter and the current-regulated current source inverter were developed in PSCAD. Various operations of the PV inverters were simulated under normal and abnormal conditions. Symmetrical and unsymmetrical faults were simulated, presented, and discussed. Both the three-phase analysis and the symmetrical component analysis were included to clarify the understanding of unsymmetrical faults. The dynamic model validation was based on the testing data provided by SCE. Testing was conducted at SCE with the focus on the grid interface behavior of the PV inverter under different faults and disturbances. The dynamic model validation covers both the symmetrical and unsymmetrical faults.

Muljadi, E.; Singh, M.; Gevorgian, V.

2013-08-01T23:59:59.000Z

283

Planar photovoltaic solar concentrator module  

DOE Patents (OSTI)

A planar photovoltaic concentrator module for producing an electrical signal from incident solar radiation includes an electrically insulating housing having a front wall, an opposing back wall and a hollow interior. A solar cell having electrical terminals is positioned within the interior of the housing. A planar conductor is connected with a terminal of the solar cell of the same polarity. A lens forming the front wall of the housing is operable to direct solar radiation incident to the lens into the interior of the housing. A refractive optical element in contact with the solar cell and facing the lens receives the solar radiation directed into the interior of the housing by the lens and directs the solar radiation to the solar cell to cause the solar cell to generate an electrical signal. An electrically conductive planar member is positioned in the housing to rest on the housing back wall in supporting relation with the solar cell terminal of opposite polarity. The planar member is operable to dissipate heat radiated by the solar cell as the solar cell generates an electrical signal and further forms a solar cell conductor connected with the solar cell terminal to permit the electrical signal generated by the solar cell to be measured between the planar member and the conductor. 5 figs.

Chiang, C.J.

1992-12-01T23:59:59.000Z

284

Planar photovoltaic solar concentrator module  

DOE Patents (OSTI)

A planar photovoltaic concentrator module for producing an electrical signal from incident solar radiation includes an electrically insulating housing having a front wall, an opposing back wall and a hollow interior. A solar cell having electrical terminals is positioned within the interior of the housing. A planar conductor is connected with a terminal of the solar cell of the same polarity. A lens forming the front wall of the housing is operable to direct solar radiation incident to the lens into the interior of the housing. A refractive optical element in contact with the solar cell and facing the lens receives the solar radiation directed into the interior of the housing by the lens and directs the solar radiation to the solar cell to cause the solar cell to generate an electrical signal. An electrically conductive planar member is positioned in the housing to rest on the housing back wall in supporting relation with the solar cell terminal of opposite polarity. The planar member is operable to dissipate heat radiated by the solar cell as the solar cell generates an electrical signal and further forms a solar cell conductor connected with the solar cell terminal to permit the electrical signal generated by the solar cell to be measured between the planar member and the conductor.

Chiang, Clement J. (New Brunswick, NJ)

1992-01-01T23:59:59.000Z

285

Skew chicane based betatron eigenmode exchange module  

DOE Patents (OSTI)

A skewed chicane eigenmode exchange module (SCEEM) that combines in a single beamline segment the separate functionalities of a skew quad eigenmode exchange module and a magnetic chicane. This module allows the exchange of independent betatron eigenmodes, alters electron beam orbit geometry, and provides longitudinal parameter control with dispersion management in a single beamline segment with stable betatron behavior. It thus reduces the spatial requirements for multiple beam dynamic functions, reduces required component counts and thus reduces costs, and allows the use of more compact accelerator configurations than prior art design methods.

Douglas, David (Yorktown, VA)

2010-12-28T23:59:59.000Z

286

Units: Cool Modules for HOT Languages  

E-Print Network (OSTI)

A module system ought to enable assembly-line programming using separate compilation and an expressive linking language. Separate compilation allows programmers to develop parts of a program independently. A linking language gives programmers precise control over the assembly of parts into a whole. This paper presents models of program units, MzScheme's module language for assembly-line programming. Units support separate compilation, independent module reuse, cyclic dependencies, hierarchical structuring, and dynamic linking. The models explain how to integrate units with untyped and typed languages such as Scheme and ML.

Matthew Flatt; Matthias Felleisen

1998-01-01T23:59:59.000Z

287

Ensuring Quality of PV Modules: Preprint  

SciTech Connect

Photovoltaic (PV) customers need to have confidence in the PV modules they purchase. Currently, no test can quantify a module's lifetime with confidence, but stress tests are routinely used to differentiate PV product designs. We suggest that the industry would be strengthened by using the wisdom of the community to develop a single set of tests that will help customers quantify confidence in PV products. This paper evaluates the need for quality assurance (QA) standards and suggests a path for creating these. Two types of standards are needed: 1) QA of the module design and 2) QA of the manufacturing process.

Kurtz, S.; Wohlgemuth, J.; Hacke, P.; Kempe, M.; Sample, T.; Yamamichi, M.; Kondo, M.; Doi, T.; Otani, K.; Amano, J.

2011-07-01T23:59:59.000Z

288

Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESSTutorial_MAINTAIN...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MAINTAINPROJECTHISTORY.doc Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS TutorialMAINTAINPROJECTHISTORY.doc Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS...

289

Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESSTutorial_ROTATION...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS TutorialROTATIONWITHINDUSTRY.doc Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS TutorialROTATIONWITHINDUSTRY.doc...

290

EIA Renewable Energy- Shipments of Photovoltaic Cells and Modules ...  

U.S. Energy Information Administration (EIA)

Renewables and Alternate Fuels > Solar Photovoltaic Cell/Module Annual Report > Annual Shipments of Photovoltaic Cells and Modules by Source: Shipments of ...

291

TEMPERATURE COEFFICIENTS FOR PV MODULES AND ARRAYS: MEASUREMENT METHODS, DIFFICULTIES, AND RESULTS  

Office of Scientific and Technical Information (OSTI)

TEMPERATURE COEFFICIENTS FOR PV MODULES AND ARRAYS: TEMPERATURE COEFFICIENTS FOR PV MODULES AND ARRAYS: MEASUREMENT METHODS, DIFFICULTIES, AND RESULTS David L. King, Jay A. Kratochvil, and William E. Boyson Sandia National Laboratories, Albuquerque, NM 0 ABSTRACT The term "temperature coefficient" has been applied to several different photovoltaic performance parameters, including voltage, current, and power. The procedures for measuring the coefficient(s) for modules and arrays are not yet standardized, and systematic influences are common in the test methods used to measure them. There are also misconceptions regarding their application. Yet, temperature coefficients, however obtained, play an important role in PV system design and sizing, where often the worst case operating condition dictates the array

292

PVSIM{copyright}: A simulation program for photovoltaic cells, modules, and arrays  

DOE Green Energy (OSTI)

An electrical simulation model for photovoltaic cells, modules, and arrays has been developed that will be useful to a wide range of analysts in the photovoltaic industry. The Microsoft{reg_sign} Windows{trademark} based program can be used to analyze individual cells, to analyze the effects of cell mismatch or reverse bias(`hot spot`) heating in modules and to analyze the performance of large arrays of modules including bypass and blocking diodes. User defined statistical variance can be applied to the fundamental parameters used to simulate the cells and diodes. The model is most appropriate for cells that can be accurately modeled using a two-diode equivalent circuit. This paper describes the simulation program and illustrates its versatility with examples.

King, D.L.; Dudley, J.K.; Boyson, W.E.

1996-06-01T23:59:59.000Z

293

Temperature coefficients for PV modules and arrays: Measurement methods, difficulties, and results  

DOE Green Energy (OSTI)

The term temperature coefficient has been applied to several different photovoltaic performance parameters, including voltage, current, and power. The procedures for measuring the coefficient(s) for modules and arrays are not yet standardized, and systematic influences are common in the test methods used to measure them. There are also misconceptions regarding their application. Yet, temperature coefficients, however obtained, play an important role in PV system design and sizing, where often the worst case operating condition dictates the array size. This paper describes effective methods for determining temperature coefficients for cells, modules, and arrays; identifies sources of systematic errors in measurements; gives typical measured values for modules; and provides guidance for their application in system engineering.

King, D.L.; Kratochvil, J.A.; Boyson, W.E.

1997-11-01T23:59:59.000Z

294

Creep in Photovoltaic Modules: Examining the Stability of Polymeric Materials and Components  

DOE Green Energy (OSTI)

Interest in renewable energy has motivated the implementation of new polymeric materials in photovoltaic modules. Some of these are non-cross-linked thermoplastics, in which there is a potential for new behaviors to occur, including phase transformation and visco-elastic flow. Differential scanning calorimetry and rheometry data were obtained and then combined with existing site-specific time-temperature information in a theoretical analysis to estimate the displacement expected to occur during module service life. The analysis identified that, depending on the installation location, module configuration and/or mounting configuration, some of the thermoplastics are expected to undergo unacceptable physical displacement. While the examples here focus on encapsulation materials, the concerns apply equally to the frame, junction-box, and mounting-adhesive technologies.

Miller, D. C.; Kempe, M. D.; Glick, S. H.; Kurtz, S. R.

2011-02-01T23:59:59.000Z

295

Stacked vapor fed amtec modules  

DOE Patents (OSTI)

The present invention pertains to a stacked AMTEC module. The invention includes a tubular member which has an interior. The member is comprised of a ion conductor that substantially conducts ions relative to electrons, preferably a beta"-alumina solid electrolyte, positioned about the interior. A porous electrode for conducting electrons and allowing sodium ions to pass therethrough, and wherein electrons and sodium ions recombine to form sodium is positioned about the beta"-alumina solid electrolyte. The electrode is operated at a temperature and a pressure that allows the recombined sodium to vaporize. Additionally, an outer current collector grid for distributing electrons throughout the porous electrode is positioned about and contacts the porous electrode. Also included in the invention is transporting means for transporting liquid sodium to the beta"-alumina solid electrolyte of the tubular member. A transition piece is positioned about the interior of the member and contacts the transporting means. The transition piece divides the member into a first cell and a second cell such that each first and second cell has a beta"-alumina solid electrolyte, a first and second porous electrode and a grid. The transition piece conducts electrons from the interior of the tubular member. There is supply means for supplying sodium to the transporting means. Preferably the supply means is a shell which surrounds the tubular member and is operated at a temperature such that the vaporized sodium condenses thereon. Returning means for returning the condensed sodium from the shell to the transporting means provides a continuous supply of liquid sodium to the transporting means. Also, there are first conducting means for conducting electric current from the transition piece which extends through the shell, and second conducting means for conducting electric current to the grid of the first cell which extends through the shell.

Sievers, Robert K. (North Huntingdon, PA)

1989-01-01T23:59:59.000Z

296

Design Review of the D0 Central Calorimeter Module Assembly to Fermi National Accelerator Laboratory  

Science Conference Proceedings (OSTI)

The D-Zero Central Calorimeter Module Assembly is a segmented ring structure consisting of an assemblage of trapezoidal modules. It is housed inside a vessel containing liquid argon. The modules contain specialized equipment for use in particle physics experiments. The design review of the D-Zero Central Calorimeter Module Assembly evaluated all major structural elements for adequacy for their design loads. They were evaluated in accordance with applicable specifications from Reference 1. The allowable stresses of the Specifications provide an approximate safety factor of 2.0 or more on failure and 1.67 on serviceability of the structure. This margin is typical of buildings, bridges, and other large structures executed in steel. To the extent that calculated stresses are less than the allowable stresses, the margin is proportionately greater. For additional conservatism to account for inherent uncertainties in estimating design loads, an arbitrary load factor of 1.25 was also applied. Design loads were calculated for deadwe1ghted plus thermal expansion, neglecting the effects of friction, and for deadweight only, considering postulated effects of friction. All of the major structural elements were found to be provisionally acceptable for their intended service and the predicted design loads. The provisions are as follows: (1) That the connect pins be fabricated of Inconel 718 or functional equivalent, instead of the originally specified Type 304 stainless steel; and (2) That conditions on bearing surfaces be modified to effectively reduce the potential coefficient of friction. The affected bearing interfaces include those between the CH, FH, and EM rings, and between the CH ring and its support members. The D-Zero Central Calorimeter Module Assembly is a segmented ring structure consisting of an assemblage of trapezoidal modules. It is housed inside a vessel containing liquid argon. The modules contain specialized equipment for use in particle physics experiments. The assembly design was reviewed to verify structural integrity and adequacy for service. Components that were evaluated were the main support beams, main support straps, module endplate brackets, module endplates, endplate connection pins, and transition pieces. Loading conditions considered were deadweight and differential thermal expansion due to specified temperature gradients. The American Institute of Steel Construction Specifications for The Design Fabrication and Erection of Structural Steel for Buildings Eighth Edition, referred to hereinafter as the AISC Specifications, were the primary acceptance criteria, where applicable. Other guidelines and engineering judgment were applied as appropriate.

Rosenfeld, M.; /Fermilab

1987-11-01T23:59:59.000Z

297

Run manager module for CORAL laboratory management  

E-Print Network (OSTI)

This thesis describes a new module, the Run Manager (RM), for Stanford Nanofabrication Facility's Common Object Representation for Advanced Laboratories (CORAL). CORAL is the lab manager with which MIT's Microsystems ...

Klann, Jeffrey G

2004-01-01T23:59:59.000Z

298

SHARP Physics Modules Updated | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Physics Modules Updated Physics Modules Updated SHARP Physics Modules Updated January 29, 2013 - 12:37pm Addthis PROTEUS Development The SHARP neutronics module, PROTEUS, includes neutron and gamma transport solvers, cross-section processing tools, and tools for depletion and fuel cycle analysis. Efforts in the second quarter focused on three major priorities: multi-physics integration, intermediate-fidelity tool development, and demonstrations of applicability. Integration of the second-order, discrete ordinates (Sn method) solver of PROTEUS with the latest version of the MOAB framework (which represents and evaluates mesh data) was initiated to enable its use for multi-physics analysis. With these updates, PROTEUS can obtain the mesh specification from the MOAB framework and store its data on the MOAB mesh representation so that MOAB

299

Rack assembly for mounting solar modules  

SciTech Connect

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures to be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Plaisted, Joshua Reed; West, Brian

2012-09-04T23:59:59.000Z

300

Rack assembly for mounting solar modules  

SciTech Connect

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Plaisted, Joshua Reed (Oakland, CA); West, Brian (San Francisco, CA)

2010-12-28T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Acceleration Modules in Linear Induction Accelerators  

E-Print Network (OSTI)

Linear Induction Accelerator (LIA) is a unique type of accelerator, which is capable to accelerate kiloAmpere charged particle current to tens of MeV energy. The present development of LIA in MHz busting mode and successful application into synchrotron broaden LIAs usage scope. Although transformer model is widely used to explain the acceleration mechanism of LIAs, it is not appropriate to consider the induction electric field as the field which accelerates charged particles for many modern LIAs. Authors examined the transition of the magnetic cores functions during LIA acceleration modules evolution, distinguished transformer type and transmission line type LIA acceleration modules, and reconsidered several related issues based on transmission line type LIA acceleration module. The clarified understanding should be helpful in the further development and design of the LIA acceleration modules.

Wang, Shaoheng

2013-01-01T23:59:59.000Z

302

Electronic spectra of strongly modulated aperiodic structures  

Science Conference Proceedings (OSTI)

We consider the tight-binding Hamiltonian on strongly modulated aperiodic chains (e.g., quasiperiodic, self-similar, random). The site energies are distributed according to a given binary sequence ([ital V][sub [ital n

Barache, D. (Laboratoire de Physique Theorique et Mathematique, Universite Paris 7, Denis Diderot, 2 place Jussieu, 75251 Paris Cedex 05 (France)); Luck, J.M. (Service de Physique Theorique, Centre d'Etudes de Saclay, 91191 Gif-sur-Yvette Cedex (France))

1994-06-01T23:59:59.000Z

303

On families of phi, Gamma-modules  

E-Print Network (OSTI)

Berger and Colmez (2008) formulated a theory of families of overconvergent tale (?,?)-modules associated to families of p-adic Galois representations over p-adic Banach algebras. In contrast with the classical theory of ...

Kedlaya, Kiran S.

304

Photovoltaic module with removable wind deflector  

DOE Patents (OSTI)

A photovoltaic (PV) module assembly including a PV module, a deflector, and a clip. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes a support arm forming a seat. The deflector defines a front face and a rear face, with the clip extending from either the trailing frame member or the rear face of the deflector. In a mounted state, the deflector is nested within the seat and is releasably mounted to the trailing frame member via the clip. In some embodiments, the support arm forms a second seat, with the PV module assembly providing a second mounted state in which the deflector is in a differing orientation/slope, nested within the second seat and releasably mounted to the trailing frame member via the clip.

Botkin, Jonathan (El Cerrito, CA); Graves, Simon (Berkeley, CA); Danning, Matt (Oakland, CA); Culligan, Matthew (Berkeley, CA)

2012-08-07T23:59:59.000Z

305

Photovoltaic module with removable wind deflector  

DOE Patents (OSTI)

A photovoltaic (PV) module assembly including a PV module, a deflector, and a clip. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes a support arm forming a seat. The deflector defines a front face and a rear face, with the clip extending from either the trailing frame member or the rear face of the deflector. In a mounted state, the deflector is nested within the seat and is releasably mounted to the trailing frame member via the clip. In some embodiments, the support arm forms a second seat, with the PV module assembly providing a second mounted state in which the deflector is in a differing orientation/slope, nested within the second seat and releasably mounted to the trailing frame member via the clip.

Botkin, Jonathan; Graves, Simon; Danning, Matt; Culligan, Matthew

2013-05-28T23:59:59.000Z

306

Radiative Measurements of Pressure Modulator Operation  

Science Conference Proceedings (OSTI)

The pressure modulator is extensively used in atmospheric measurements but is not well characterized in terms of its spectroscopic operation. A series of measurements on a carbon monoxide radiometer is described and comparisons are made with ...

J. R. Drummond; A. Ashton

1990-02-01T23:59:59.000Z

307

PV Module Reliability Research (Fact Sheet)  

DOE Green Energy (OSTI)

This National Center for Photovoltaics sheet describes the capabilities of its PV module reliability research. The scope and core competencies and capabilities are discussed and recent publications are listed.

Not Available

2013-06-01T23:59:59.000Z

308

Residential Sector Demand Module 2000, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

1999-12-01T23:59:59.000Z

309

Residential Sector Demand Module 2004, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2004-02-01T23:59:59.000Z

310

Residential Sector Demand Module 2001, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2000-12-01T23:59:59.000Z

311

Residential Sector Demand Module 2002, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2001-12-01T23:59:59.000Z

312

Residential Sector Demand Module 2005, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2005-04-01T23:59:59.000Z

313

Residential Sector Demand Module 2003, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2003-01-01T23:59:59.000Z

314

Residential Sector Demand Module 2008, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2008-10-10T23:59:59.000Z

315

Residential Sector Demand Module 2006, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2006-03-01T23:59:59.000Z

316

Residential Sector Demand Module 2009, Model Documentation  

Reports and Publications (EIA)

Model Documentation - Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2009-05-01T23:59:59.000Z

317

Residential Sector Demand Module 1999, Model Documentation  

Reports and Publications (EIA)

This is the fifth edition of the Model Documentation Report: Residential Sector DemandModule of the National Energy Modeling System (NEMS). It reflects changes made to themodule over the past year for the Annual Energy Outlook 1999.

John H. Cymbalsky

1998-12-01T23:59:59.000Z

318

Residential Sector Demand Module 2007, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2007-04-26T23:59:59.000Z

319

Modulation of Electrical Transport and Photosensitivity of ...  

Science Conference Proceedings (OSTI)

Modulation of channel carrier mobility and dielectric layer characteristics will be ... Crystal Growth and Characterization of YAG Crystals for Scintillator ... Effect of F Impurity Concentration upon Electronic and Electrical Features of SnO2.

320

Nondestructive Performance Characterization Techniques for Module Reliability  

DOE Green Energy (OSTI)

This paper describes nondestructive characterization techniques for module reliability. These techniques include light and dark current versus voltage and related analysis such as resistance, diode quality factor, and dark current. The use of the NREL laser scanner at zero volts and forward bias is also described as a technique to uncover cracks, shunts, and open-circuit regions in a module. Quantum-efficiency measurements of isolated cells or regions in a module are also possible. The interpretation of laser-scanning data is enhanced by hot-spot testing with an infrared camera or thermographic paper. Specialized nondestructive techniques have also been developed to determine the shunt resistance of individual cells in a module by selective shading of cells under sunlight. Ultraviolet fluorescence and reflectivity measurements at NREL have proven useful in evaluating encapsulant stability.

Emery, K.

2003-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Project Execution Plan Review Module (RM)  

Energy.gov (U.S. Department of Energy (DOE))

The Project Execution Plan (PEP) Review Module (RM) is a tool that assists DOE federal project review teams in evaluating the adequacy of the PEP development and maintenance for projects of any...

322

Education of Risk Professionals Module 3  

Science Conference Proceedings (OSTI)

The recent expansion of risk-informed initiatives in the nuclear power industry, combined with increasing mobility and retirement of trained personnel, underscores the need for professionals trained in risk methods. To address this need, EPRI developed the Education of Risk Professionals program. This is a formal training program designed to accelerate utility qualification of new risk professionals. The program consists of the following six modules; each module is taught over a 1-week period in a manner...

2011-12-23T23:59:59.000Z

323

WRAP Module 1 waste analysis plan  

Science Conference Proceedings (OSTI)

The purpose of this waste analysis plan is to document the necessary characterization, sampling, screening, analysis, and waste acceptance criteria for waste received at the WRAP Module 1. Waste expected to be received at WRAP Module 1 includes newly generated and retrieved waste. The newly generated waste will undergo verification prior to treatment, storage, or disposal. Retrieved waste from the burial grounds or above ground storage will undergo further characterization (as needed), treatment, supercompaction, and repackaging

Mayancsik, B.A.

1995-09-22T23:59:59.000Z

324

AN AB INITIO MODEL FOR COSMIC-RAY MODULATION  

SciTech Connect

A proper understanding of the effects of turbulence on the diffusion and drift of cosmic rays (CRs) is of vital importance for a better understanding of CR modulation in the heliosphere. This study presents an ab initio model for CR modulation, incorporating for the first time the results yielded by a two-component turbulence transport model. This model is solved for solar minimum heliospheric conditions, utilizing boundary values chosen so that model results are in reasonable agreement with spacecraft observations of turbulence quantities in the solar ecliptic plane and along the out-of-ecliptic trajectory of the Ulysses spacecraft. These results are employed as inputs for modeled slab and two-dimensional (2D) turbulence energy spectra. The modeled 2D spectrum is chosen based on physical considerations, with a drop-off at the very lowest wavenumbers. There currently exist no models or observations for the wavenumber where this drop-off occurs, and it is considered to be the only free parameter in this study. The modeled spectra are used as inputs for parallel mean free path expressions based on those derived from quasi-linear theory and perpendicular mean free paths from extended nonlinear guiding center theory. Furthermore, the effects of turbulence on CR drifts are modeled in a self-consistent way, also employing a recently developed model for wavy current sheet drift. The resulting diffusion and drift coefficients are applied to the study of galactic CR protons and antiprotons using a 3D, steady-state CR modulation code, and sample solutions in fair to good agreement with multiple spacecraft observations are presented.

Engelbrecht, N. E.; Burger, R. A. [Center for Space Research, North-West University, Potchefstroom 2520 (South Africa)

2013-07-20T23:59:59.000Z

325

Applied Science and Technology Task Order Fiscal Year 2009 Year...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

09 Year-End Summary Report Applied Science and Technology Task Order Fiscal Year 2009 Year-End Summary Report Applied Science and Technology Task Order Fiscal Year 2009 Year-End...

326

Applied Science and Technology Task Order Fiscal Year 2010 Year...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 Year-End Summary Report Applied Science and Technology Task Order Fiscal Year 2010 Year-End Summary Report Applied Science and Technology Task Order Fiscal Year 2010 Year-End...

327

Applied Science and Technology Task Order Fiscal Year 2011 Year...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 Year-End Summary Report Applied Science and Technology Task Order Fiscal Year 2011 Year-End Summary Report Applied Science and Technology Task Order Fiscal Year 2011 Year-End...

328

Applied Science and Technology Task Order Fiscal Year 2008 Year...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 Year-End Summary Report Applied Science and Technology Task Order Fiscal Year 2008 Year-End Summary Report Applied Science and Technology Task Order Fiscal Year 2008 Year-End...

329

Proceedings of the 2011 ACM Symposium on Applied Computing  

Science Conference Proceedings (OSTI)

Welcome to the 26th International Symposium on Applied Computing (SAC 2011). For the past 25 years, SAC has become a major international venue for computing researchers and applied practitioners to convene and share ideas on recent developments in a ...

William Chu; W. Eric Wong; Mathew J. Palakal; Chih-Cheng Hung

2011-03-01T23:59:59.000Z

330

Proceedings of the 2010 ACM Symposium on Applied Computing  

Science Conference Proceedings (OSTI)

Welcome to the 25th International Symposium on Applied Computing (SAC 2010). For the past 24 years, SAC has become a major international venue for computing researchers and applied practitioners to convene and share ideas on recent developments in a ...

Sung Y. Shin; Sascha Ossowski; Michael Schumacher; Mathew J. Palakal; Chih-Cheng Hung

2010-03-01T23:59:59.000Z

331

DOE - Office of Legacy Management -- Case School of Applied Science...  

Office of Legacy Management (LM)

Case School of Applied Science Ohio State University - OH 0-01 FUSRAP Considered Sites Site: Case School of Applied Science, Ohio State University (OH.0-01 ) Eliminated from...

332

Roadmap: Applied Engineering Manufacturing Systems Bachelor of Science  

E-Print Network (OSTI)

Roadmap: Applied Engineering ­ Manufacturing Systems ­ Bachelor of Science [AT 15000 Introduction to Human Communication 3 Fulfills Kent Core Additional Kent Core Requirement 3 See #12;Roadmap: Applied Engineering ­ Manufacturing Systems ­ Bachelor of Science [AT

Sheridan, Scott

333

Open Solicitations and How to Apply: the Loan Guarantee Program...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Open Solicitations and How to Apply: the Loan Guarantee Program Invites You to a Free Webinar Open Solicitations and How to Apply: the Loan Guarantee Program Invites You to a Free...

334

Robust optimization of intensity modulated proton therapy  

SciTech Connect

Purpose: Intensity modulated proton therapy (IMPT) is highly sensitive to range uncertainties and uncertainties caused by setup variation. The conventional inverse treatment planning of IMPT optimized based on the planning target volume (PTV) is not often sufficient to ensure robustness of treatment plans. In this paper, a method that takes the uncertainties into account during plan optimization is used to mitigate the influence of uncertainties in IMPT. Methods: The authors use the so-called ''worst-case robust optimization'' to render IMPT plans robust in the face of uncertainties. For each iteration, nine different dose distributions are computed--one each for {+-} setup uncertainties along anteroposterior (A-P), lateral (R-L) and superior-inferior (S-I) directions, for {+-} range uncertainty, and the nominal dose distribution. The worst-case dose distribution is obtained by assigning the lowest dose among the nine doses to each voxel in the clinical target volume (CTV) and the highest dose to each voxel outside the CTV. Conceptually, the use of worst-case dose distribution is similar to the dose distribution achieved based on the use of PTV in traditional planning. The objective function value for a given iteration is computed using this worst-case dose distribution. The objective function used has been extended to further constrain the target dose inhomogeneity. Results: The worst-case robust optimization method is applied to a lung case, a skull base case, and a prostate case. Compared with IMPT plans optimized using conventional methods based on the PTV, our method yields plans that are considerably less sensitive to range and setup uncertainties. An interesting finding of the work presented here is that, in addition to reducing sensitivity to uncertainties, robust optimization also leads to improved optimality of treatment plans compared to the PTV-based optimization. This is reflected in reduction in plan scores and in the lower normal tissue doses for the same coverage of the target volume when subjected to uncertainties. Conclusions: The authors find that the worst-case robust optimization provides robust target coverage without sacrificing, and possibly even improving, the sparing of normal tissues. Our results demonstrate the importance of robust optimization. The authors assert that all IMPT plans should be robustly optimized.

Liu Wei; Zhang Xiaodong; Li Yupeng; Mohan, Radhe [Department of Radiation Physics, University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States)

2012-02-15T23:59:59.000Z

335

PLZT NANO PRE URSORS FOR HIGH ENERGY DENSITY APPLI ATIONS  

APPLI ATIONS & INDUSTRIES ENEFITS Pulsed Power Oil Exploration Capacitors Refer to SD # 12119 Thermistors Transducers Military & Defense Automotive

336

Dixson and Fu Receive NIST Applied Research Award  

Science Conference Proceedings (OSTI)

Dixson and Fu Receive NIST Applied Research Award. For Immediate Release: December 1, 1999. *. Bookmark and Share. ...

2013-07-19T23:59:59.000Z

337

Materials Research Applied to National Needs (MARANN) in Honor ...  

Science Conference Proceedings (OSTI)

Jul 31, 2012 ... About this Symposium. Meeting, 2013 TMS Annual Meeting & Exhibition. Symposium, Materials Research Applied to National Needs...

338

PHOTOGRAMMETRIC ENGINEERING & REMOTE SENSING 1 ADVISER: Immersive Scientific Visualization Applied  

E-Print Network (OSTI)

be applied to the terrain (Figure 2b). A custom pixel shader was integrated with ROAM to render the dynamic

Head III, James William

339

Application of the NREL Test-to-Failure Protocol for PV Modules  

DOE Green Energy (OSTI)

Initial results of application of the NREL Test-to-Failure Protocol are presented and discussed. Six commercially available multicrystalline Si-cell flat-plate modules were subjected to the protocol with controls. The samples were divided among three test sequences, (1) 1000 hours of 85C/85% relative humidity with positive or negative 600 V bias to the active layers with respect to the grounded frame, (2) -40/85C thermal cycling with electrical load at the rated module power, and (3) an alternating sequence between tests (1) and (2). Application of the protocol manifested in the acceleration of degradation mechanisms seen in the field including backsheet delamination, corrosion, bubble formation within the laminate, discoloration of the antireflective coating, and localized heating with degradation of the backsheet as a result of moisture ingress, corrosion, and concentrated current flow. Significant differences in performance after one round of the protocol are seen in damp heat depending on the polarity of the bias applied to the active layer (the short-circuited power leads of the module). The protocol is found to successfully accelerate module degradation mechanisms that have been observed in the field and will help to differentiate the performance and reliability of various module technologies.

Hacke, P.; Osterwald, C.; Trudell, D.; Terwilliger, K.; Bosco, N.; Oelak, E.; Kurtz, S.

2011-02-01T23:59:59.000Z

340

Discrete pulse modulation strategies for high-frequency inverter systems  

SciTech Connect

High-performance high-frequency inverter systems for UPS applications represent a demanding application that cannot be easily realized using conventional hard-switched PWM inverter topologies. Adoption of typical soft-switched inverters such as the resonant dc link inverter require the use of discrete pulse modulation strategies. New controller structures are necessary to cope with stringent voltage regulation and distortion constraints in the presence of unbalanced and nonlinear loads. This paper presents a controller that utilizes load current feed-forward strategy with a cost function current regulator to achieve excellent transient performance characteristics. Voltage regulation is ensured using a synchronous frame regulator. Detailed simulation and experimental results verifying the concepts are presented. Although this paper focuses on soft-switching inverters, the control concepts can be applied to conventional hard-switching inverters as well.

Venkataramanan, G. (Montana State Univ., Bozeman, MT (United States). Dept. of Electrical Engineering); Divan, D.M. (Univ. of Wisconsin, Madison, WI (United States). Dept. of Electrical and Computer Engineering); Jahns, T.M. (General Electric Co., Schenectady, NY (United States))

1993-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Application of nonlinear wave modulation spectroscopy to discern material damage  

SciTech Connect

Materials containing structural damage have a far greater nonlinear elastic response than materials with no structural damage. This is the basis for nonlinear wave diagnostics of damage, methods which are remarkably sensitive to the detection and progression of damage in materials. Here the authors describe one nonlinear method, the application of harmonics and sum and difference frequency to discern damage in materials. The method is termed Nonlinear Wave Modulation Spectroscopy (NWMS). It consists of exciting a sample with continuous waves of two separate frequencies simultaneously, and inspecting the harmonics of the two waves, and their sum and difference frequencies (sidebands). Undamaged materials are essentially linear in their response to the two waves, while the same material, when damaged, becomes highly nonlinear, manifested by harmonics and sideband generation. The authors illustrate the method by experiments on uncracked and cracked plexiglass and sandstone samples, and by applying it to intact and damaged engine components.

Johnson, P.A. [Los Alamos National Lab., NM (United States); Sutin, A. [Stevens Inst. of Tech., Hoboken, NJ (United States); Abeele, K.E.A. van den [Catholic Univ. Leuven (Belgium). Dept. of Building Physics

1999-04-01T23:59:59.000Z

342

Testing and Analysis for Lifetime Prediction of Crystalline Silicon PV Modules Undergoing Degradation by System Voltage Stress: Preprint  

DOE Green Energy (OSTI)

Acceleration factors are calculated for crystalline silicon PV modules under system voltage stress by comparing the module power during degradation outdoors to that in accelerated testing at three temperatures and 85% relative humidity. A lognormal analysis is applied to the accelerated lifetime test data considering failure at 80% of the initial module power. Activation energy of 0.73 eV for the rate of failure is determined, and the probability of module failure at an arbitrary temperature is predicted. To obtain statistical data for multiple modules over the course of degradation in-situ of the test chamber, dark I-V measurements are obtained and transformed using superposition, which is found well suited for rapid and quantitative evaluation of potential-induced degradation. It is determined that shunt resistance measurements alone do not represent the extent of power degradation. This is explained with a two-diode model analysis that shows an increasing second diode recombination current and ideality factor as the degradation in module power progresses. Failure modes of the modules stressed outdoors are examined and compared to those stressed in accelerated tests.

Hacke, P.; Smith, R.; Terwiliger, K.; Glick, S.; Jordan, D.; Johnston, S.; Kempe, M.; Kurtz, S.

2012-07-01T23:59:59.000Z

343

ISHED1: Applying the LEM Methodology to Heat Exchanger Design  

E-Print Network (OSTI)

ISHED1: Applying the LEM Methodology to Heat Exchanger Design Kenneth A. Kaufman Ryszard S. Michalski MLI 00-2 #12;2 ISHED1: APPLYING THE LEM METHODOLOGY TO HEAT EXCHANGER DESIGN Kenneth A. Kaufman-2 January 2000 #12;ISHED1: APPLYING THE LEM METHODOLOGY TO HEAT EXCHANGER DESIGN Abstract Evolutionary

Michalski, Ryszard S.

344

Injection-locked composite lasers for mm-wave modulation : LDRD 117819 final report.  

Science Conference Proceedings (OSTI)

This report summarizes a 3-year LDRD program at Sandia National Laboratories exploring mutual injection locking of composite-cavity lasers for enhanced modulation responses. The program focused on developing a fundamental understanding of the frequency enhancement previously demonstrated for optically injection locked lasers. This was then applied to the development of a theoretical description of strongly coupled laser microsystems. This understanding was validated experimentally with a novel 'photonic lab bench on a chip'.

Wendt, Joel Robert; Vawter, Gregory Allen; Raring, James; Tauke-Pedretti, Anna; Alford, Charles Fred (Sandia Staffing Alliance, LLC, Albuquerque, NM); Skogen, Erik J.; Chow, Weng Wah; Cajas, Florante G. (LMATA Government Services, LLC, Albuquerque, NM); Overberg, Mark E.; Torres, David L. (LMATA Government Services, LLC, Albuquerque, NM); Peake, Gregory Merwin

2010-09-01T23:59:59.000Z

345

Nonlinear modal interaction in HVDC/AC power systems with dc power modulation  

Science Conference Proceedings (OSTI)

In this paper investigation of nonlinear modal interaction using the normal form of vector fields technique is extended to HVDC/AC power systems with dc power modulation. The ac-dc interface equations are solved to form a state space model with second order approximation. Using the normal form technique, the system`s nonlinear dynamic characteristics are obtained. The proposed approach is applied to a 4-generator HVDC/AC test power system, and compare with the time domain solution.

Ni, Y.X. [Tsinghua Univ., Beijing (China); Vittal, V.; Kliemann, W.; Fouad, A.A. [Iowa State Univ., Ames, IA (United States)

1996-11-01T23:59:59.000Z

346

Bit-Interleaved Coded Modulation in the Wideband Regime  

Science Conference Proceedings (OSTI)

The wideband regime of bit-interleaved coded modulation (BICM) in Gaussian channels is studied. The Taylor expansion of the coded modulation capacity for generic signal constellations at low signal-to-noise ratio (SNR) is derived and used to determine ... Keywords: Additive white Gaussian noise (AWGN) channel, Rayleigh fading channel, bit-interleaved coded modulation, coded modulation, wideband regime

A. Martinez; A. Guillen i Fabregas; G. Caire; F. Willems

2008-12-01T23:59:59.000Z

347

Development of a commercial photovoltaic concentrator module  

DOE Green Energy (OSTI)

The ojective of this work was to develop the design and prototype of a commercial high-concentration photovoltaic (PV) module. The design is for a 282-sun point-focus concentrating module. Most of the components, subassemblies, and design features incorporate simplifications and ease of manufacturing. The Solar Kinetics, Inc. (SKI) module is designed to incorporate high-efficiency, single-crystal silicon PV cells. The housing is made with aluminum laminated for voltage stand-off and simultaneously providing high thermal conductivity. The Fresnel lens injection molded by American Optical (AO) as singles. The cell assembly consists of a copper heat spreader, a photovoltaic cell soldered, a top and bottom contact, and a reflective secondary optical element (SOE). The cell assemblies passed all of the initial electrical characterization and high-potential tests. Under environmental cycling, the only bond that failed was the PV cell-to-heat spreader interface. The other components (top contact, bottom contact, SOE) passed all the environmental cycling tests. The cell assemblies were designed to be mounted onto the receiver section with a thermally conductive RTV. This geometry was subjected to environmental testing. There was no delamination of this bond nor was there electrical breakdown when the assemblies were subjected to the hi-pot test. A mock module was fabricated for environmental evaluation. This module was subjected to the humidity/freeze cycling to assess the performance of the lens mounting design. This module was also subjected to the rain test after the humidity/freeze cycling and checked for water leaks. The lens showed small displacement from its original position after the environmental cycling. One tablespoon of water did collect inside the module.

Saifee, S.T.; Hutchison, G. [Solar Kinetics, Inc., Dallas, TX (United States)

1992-09-01T23:59:59.000Z

348

Vehicle Technologies Office: Lightweight Materials Long-Term Applied  

NLE Websites -- All DOE Office Websites (Extended Search)

Long-Term Applied Research: Magnesium and Carbon Fiber to someone by E-mail Long-Term Applied Research: Magnesium and Carbon Fiber to someone by E-mail Share Vehicle Technologies Office: Lightweight Materials Long-Term Applied Research: Magnesium and Carbon Fiber on Facebook Tweet about Vehicle Technologies Office: Lightweight Materials Long-Term Applied Research: Magnesium and Carbon Fiber on Twitter Bookmark Vehicle Technologies Office: Lightweight Materials Long-Term Applied Research: Magnesium and Carbon Fiber on Google Bookmark Vehicle Technologies Office: Lightweight Materials Long-Term Applied Research: Magnesium and Carbon Fiber on Delicious Rank Vehicle Technologies Office: Lightweight Materials Long-Term Applied Research: Magnesium and Carbon Fiber on Digg Find More places to share Vehicle Technologies Office: Lightweight

349

Microsoft PowerPoint - FinalModule3.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3: Project Scheduling 3: Project Scheduling Prepared by: Module 3 - Project Scheduling 1 Prepared by: Booz Allen Hamilton Module 3: Project Scheduling Welcome to Module 3. The objective of this module is to introduce you to Project Scheduling. The Topics that will be addressed in this Module include: * Define Planning vs. Scheduling * Define and Illustrate Basic Scheduling Concepts * Define Logic Relationships and Critical Path * Define and Illustrate Different Schedule Formats Module 3 - Project Scheduling 2 Prepared by: Booz Allen Hamilton Review of Previous Modules Let's quickly review what has been covered in the previous modules. * In Module 1 we introduced you to earned value and the requirements for properly implementing an earned value management system (EVMS). * In Module 2 we discussed

350

Microsoft PowerPoint - FinalModule8.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8: Reporting 8: Reporting Prepared by: Module 8 - Reporting 1 Prepared by: Booz Allen Hamilton Module 8: Government Required Reports Welcome to Module 8. The objective of this module is to introduce you to Government required reports. The Topics that will be addressed in this Module include: * Define Cost Performance Report (CPR) * Define Cost/Schedule Status Report (C/SSR) Module 8 - Reporting 2 Prepared by: Booz Allen Hamilton Review of Previous Modules In the previous seven modules, we discussed the framework needed to perform Earned Value and develop an Earned Value Management System (EVMS). * In Module 1 we introduced you to earned value and the requirements for properly implementing an earned value management system (EVMS) * In Module 2 we discussed the development of the work breakdown structure

351

ESP-The Electrical submersible pump. Part 7. Applying variable frequency drives to ESPs  

SciTech Connect

To keep pace with technology, the oil industry has begun using variable frequency drives on electrical submersible pumps. Applying variable frequency drives on ESPs began seriously in 1977. In March 1983, there were approximately 350 variable frequency drives successfully operating on electrical submersible pumps throughout the world. Three types of variable frequency drives available today are the current source inverter, the pulse width modulation, and the variable voltage source inverter. As all three types have good points and bad, a short discussion of each type is essential to understand why the variable voltage inverter is used most often in oil field applications and why it has been a success. A current source inverter typically uses a phasecontrolled rectifier to generate variable DC current. The phase-controlled rectifier produces the required current which is subsequently filtered by a DC link reactor. The inverter then produces the desired variable frequency current and the motor voltage varies with load.

Watson, A.J.

1983-11-15T23:59:59.000Z

352

Module/array interface study. Final report  

SciTech Connect

Bechtel National, Inc. has conducted a study of alternate module, panel, and array designs for use in large scale applications such as central station photovoltaic power plants. The objective of the study is to identify design features that will lead to minimum plant costs. Several aspects of module design are evaluated, including glass superstrate and metal substrate module configurations, the potential for hail damage, light absorption in glass superstrates, the economics of glass selection, and electrical design. Also, three alternate glass superstrate module configurations are evaluated by means of finite element computer analyses. Two panel sizes, 1.2 by 2.4 m (4 by 8 ft) and 2.4 by 4.8 m (8 by 16 ft), are used to support three module sizes, 0.6 by 1.2 m (2 by 4 ft), 1.2 by 1.2 m (4 by 4 ft), and 1.2 by 2.4 m (4 by 8 ft), for design loadings of +- 1.7 kPa (35 psf), +- 2.4 kPa (50 psf), and +- 3.6 kPa (75 psf). Designs and cost estimates are presented for twenty panel types and nine array configurations at each of the three design loadings. Structural cost sensitivities of combined array configurations and panel cases are presented.

1978-08-01T23:59:59.000Z

353

Three dimensional, multi-chip module  

DOE Patents (OSTI)

The present invention relates to integrated circuit packaging technology, and particularly to three dimensional packages involving high density stacks of integrated circuits. A plurality of multi-chip modules are stacked and bonded around the perimeter by sold-bump bonds to adjacent modules on, for instance, three sides of the perimeter. The fourth side can be used for coolant distribution, for more interconnect structures, or other features, depending on particular design considerations of the chip set. The multi-chip modules comprise a circuit board, having a planarized interconnect structure formed on a first major surface, and integrated circuit chips bonded to the planarized interconnect surface. Around the periphery of each circuit board, long, narrow ``dummy chips`` are bonded to the finished circuit board to form a perimeter wall. The wall is higher than any of the chips on the circuit board, so that the flat back surface of the board above will only touch the perimeter wall. Module-to-module interconnect is laser-patterned on the sides of the boards and over the perimeter wall in the same way and at the same time that chip to board interconnect may be laser-patterned.

Bernhardt, A.F.; Petersen, R.W.

1992-12-31T23:59:59.000Z

354

Single, stretched membrane, structural module experiments  

DOE Green Energy (OSTI)

This report describes tests done on stretched-membrane heliostats used to reflect solar radiation onto a central receiver. The tests were used to validate prior analysis and mathematical models developed to describe module performance. The modules tested were three meters in diameter and had reflective polymer film laminated to the membrane. The frames were supported at three points equally spaced around the ring. Three modules were pneumatically attached with their weight suspended at the bottom support, two were pneumatically attached with their weight suspended from the upper mounts, and one was rigidly attached with its weight suspended at the bottom mount. By varying the membrane tension we could simulate a uniform wind loading normal to the mirror's surface. A video camera 15+ meters away from the mirror recorded the virtual image of a target grid as reflected by the mirrors' surface. The image was digitized and stored on a microcomputer. Using the law of reflection and analytic geometry, we computed the surface slopes of a sampling of points on the surface. The dominant module response was consistent with prior SERI analyses. The simple analytical model is quite adequate for designing and sizing single-membrane modules if the initial imperfections and their amplification are appropriately controlled. To avoid potential problems resulting from the fundamentally n = 2 deformation phenomena, we advise using either relatively stiffer ring frames or more than three support points.

Wood, R.L.

1986-02-01T23:59:59.000Z

355

electricity market module region | OpenEI  

Open Energy Info (EERE)

342 342 Varnish cache server Browse Upload data GDR 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142281342 Varnish cache server electricity market module region Dataset Summary Description This dataset comes from the Energy Information Administration (EIA), and is part of the 2011 Annual Energy Outlook Report (AEO2011). Source EIA Date Released April 26th, 2011 (3 years ago) Date Updated Unknown Keywords AEO Electricity electricity market module region generation capacity Data application/vnd.ms-excel icon AEO2011: Electricity Generation Capacity by Electricity Market Module Region and Source- Reference Case (xls, 10.6 KiB) Quality Metrics Level of Review Peer Reviewed Comment Temporal and Spatial Coverage Frequency Annually

356

Scannerless loss modulated flash color range imaging  

SciTech Connect

Scannerless loss modulated flash color range imaging methods and apparatus are disclosed for producing three dimensional (3D) images of a target within a scene. Apparatus and methods according to the present invention comprise a light source providing at least three wavelengths (passbands) of illumination that are each loss modulated, phase delayed and simultaneously directed to illuminate the target. Phase delayed light backscattered from the target is spectrally filtered, demodulated and imaged by a planar detector array. Images of the intensity distributions for the selected wavelengths are obtained under modulated and unmodulated (dc) illumination of the target, and the information contained in the images combined to produce a 3D image of the target.

Sandusky, John V. (Albuquerque, NM); Pitts, Todd Alan (Rio Rancho, NM)

2009-02-24T23:59:59.000Z

357

Scannerless loss modulated flash color range imaging  

SciTech Connect

Scannerless loss modulated flash color range imaging methods and apparatus are disclosed for producing three dimensional (3D) images of a target within a scene. Apparatus and methods according to the present invention comprise a light source providing at least three wavelengths (passbands) of illumination that are each loss modulated, phase delayed and simultaneously directed to illuminate the target. Phase delayed light backscattered from the target is spectrally filtered, demodulated and imaged by a planar detector array. Images of the intensity distributions for the selected wavelengths are obtained under modulated and unmodulated (dc) illumination of the target, and the information contained in the images combined to produce a 3D image of the target.

Sandusky, John V. (Albuquerque, NM); Pitts, Todd Alan (Rio Rancho, NM)

2008-09-02T23:59:59.000Z

358

ILC Marx Modulator Development Program Status  

DOE Green Energy (OSTI)

Development of a first generation prototype (P1) Marx-topology klystron modulator for the International Linear Collider is nearing completion at the Stanford Linear Accelerator Center. It is envisioned as a smaller, lower cost, and higher reliability alternative to the present, bouncer-topology, 'Baseline Conceptual Design'. The Marx presents several advantages over conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at ILC parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. The P1-Marx employs all solid state elements; IGBTs and diodes, to control the charge, discharge and isolation of the cells. A general overview of the modulator design and the program status are presented.

Burkhart, C.; Beukers, T.; Larsen, R.; Macken, K.; Nguyen, M.; Olsen, J.; Tang, T.; /SLAC

2009-03-04T23:59:59.000Z

359

Development of Fuel Shuffling Module for PHISICS  

SciTech Connect

PHISICS (Parallel and Highly Innovative Simulation for the INL Code System) [4] code toolkit has been in development at the Idaho National Laboratory. This package is intended to provide a modern analysis tool for reactor physics investigation. It is designed with the mindset to maximize accuracy for a given availability of computational resources and to give state of the art tools to the modern nuclear engineer. This is obtained by implementing several different algorithms and meshing approaches among which the user will be able to choose, in order to optimize his computational resources and accuracy needs. The software is completely modular in order to simplify the independent development of modules by different teams and future maintenance. The package is coupled with the thermo-hydraulic code RELAP5-3D [3]. In the following the structure of the different PHISICS modules is briefly recalled, focusing on the new shuffling module (SHUFFLE), object of this paper.

Allan Mabe; Andrea Alfonsi; Cristian Rabiti; Aaron Epiney; Michael Lineberry

2013-06-01T23:59:59.000Z

360

Module level solutions to solar cell polarization  

Science Conference Proceedings (OSTI)

A solar cell module includes interconnected solar cells, a transparent cover over the front sides of the solar cells, and a backsheet on the backsides of the solar cells. The solar cell module includes an electrical insulator between the transparent cover and the front sides of the solar cells. An encapsulant protectively packages the solar cells. To prevent polarization, the insulator has resistance suitable to prevent charge from leaking from the front sides of the solar cells to other portions of the solar cell module by way of the transparent cover. The insulator may be attached (e.g., by coating) directly on an underside of the transparent cover or be a separate layer formed between layers of the encapsulant. The solar cells may be back junction solar cells.

Xavier, Grace (Fremont, CA), Li; Bo (San Jose, CA)

2012-05-29T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Control of Moisture Ingress into Photovoltaic Modules  

DOE Green Energy (OSTI)

During long-term exposure of photovoltaic modules to environmental stress, the ingress of water into the module is correlated with decreased performance. By using diffusivity measurements for water through encapsulants such as ethylene vinyl acetate (EVA), we have modeled moisture ingress using a finite-element analysis with atmospheric data from various locations such as Miami, Florida. This analysis shows that because of the high diffusivity of EVA, even an impermeable glass back-sheet alone is incapable of preventing significant moisture ingress from the edges for a 20-year lifecycle. This result has led us to investigate ways to protect modules from moisture through the use of different encapsulating chemistries and materials.

Kempe, M. D.

2005-02-01T23:59:59.000Z

362

Siemens SOFC Test Article and Module Design  

SciTech Connect

Preliminary design studies of the 95 kWe-class SOFC test article continue resulting in a stack architecture of that is 1/3 of 250 kWe-class SOFC advanced module. The 95 kWeclass test article is envisioned to house 20 bundles (eight cells per bundle) of Delta8 cells with an active length of 100 cm. Significant progress was made in the conceptual design of the internal recirculation loop. Flow analyses were initiated in order to optimize the bundle row length for the 250 kWeclass advanced module. A preferred stack configuration based on acceptable flow and thermal distributions was identified. Potential module design and analysis issues associated with pressurized operation were identified.

None

2011-03-31T23:59:59.000Z

363

Low thermal resistance power module assembly  

DOE Patents (OSTI)

A power module assembly with low thermal resistance and enhanced heat dissipation to a cooling medium. The assembly includes a heat sink or spreader plate with passageways or openings for coolant that extend through the plate from a lower surface to an upper surface. A circuit substrate is provided and positioned on the spreader plate to cover the coolant passageways. The circuit substrate includes a bonding layer configured to extend about the periphery of each of the coolant passageways and is made up of a substantially nonporous material. The bonding layer may be solder material which bonds to the upper surface of the plate to provide a continuous seal around the upper edge of each opening in the plate. The assembly includes power modules mounted on the circuit substrate on a surface opposite the bonding layer. The power modules are positioned over or proximal to the coolant passageways.

Hassani, Vahab (Denver, CO); Vlahinos, Andreas (Castle Rock, CO); Bharathan, Desikan (Arvada, CO)

2007-03-13T23:59:59.000Z

364

How to Apply for an SES Position | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How to Apply for an SES Position How to Apply for an SES Position How to Apply for an SES Position The Senior Executive Service (SES) is an elite group of men and women meeting the highest professional standards who administer public programs at the top levels of the Federal government. SES employees' salaries are linked directly to individual performance. The U.S. Office of Personnel Management's (OPM) SES web page contains a host of information that may be benefical to you. To apply for current SES positions within the Federal Government, including the Department of Energy please visit the Office of Personnel Management's USAJOBS site. From this site, you may view, download and apply for vacancies of interest to you. DOE does not accept unsolicited resumes. You must apply to a specific

365

Apply for Our Jobs | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Apply for Our Jobs | National Nuclear Security Administration Apply for Our Jobs | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog The National Nuclear Security Administration Apply for Our Jobs Home > Federal Employment > Apply for Our Jobs Apply for Our Jobs Whether you're a student seeking to learn more about a future career, just starting out, at mid-career or an experienced executive, NNSA may have the

366

Apply for Our Jobs | National Nuclear Security Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

Apply for Our Jobs | National Nuclear Security Administration Apply for Our Jobs | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog The National Nuclear Security Administration Apply for Our Jobs Home > Federal Employment > Apply for Our Jobs Apply for Our Jobs Whether you're a student seeking to learn more about a future career, just starting out, at mid-career or an experienced executive, NNSA may have the

367

Analyses of Klystron Modulator Approaches for NLC  

SciTech Connect

Major changes to the Next Linear Collider (NLC) design were facilitated by the experimental testing of the 75 MW X-band klystron at a 3.0 {micro}sec pulse width and new component development allowing the delay line distribution system (DLDS) to operate with eight bins instead of four. This change has a direct effect on the design of the klystron modulator. The general approaches, which are being studied intensively, are: the conventional base line modulator with two klystrons, a Hybrid version of the baseline with a solid-state on/off switch, a solid-state induction type modulator that drives eight klystrons, and a solid-state direct switch modulator. Some form of pulse transformer is the matching element between the klystron beam and the energy store in the all of these approaches except the direct switch. The volume and cost of the transformer is proportional to the peak pulse power and the output pulse width. The recent change in the NLC design requires double the transformer effective core area, and increase both the size and cost of modulator. In the direct switch model there is no pulse transformer. The klystron beam potential is practically equal to the potential of the energy storage element. Here the solid-state switch blocks the 500 kV DC voltage of the storage element. In this paper transformerless modulator approaches are presented based upon a Marx method of voltage multiplication using on/off Insulated Gate Bipolar Transistors (IGBT's) instead of on switches. DC voltage power supply system is much simpler as compared to the power system of the direct switch approach.

Krasnykh, Anatoly

2000-08-24T23:59:59.000Z

368

Challenges in Applying Diamond Coatings to Carbide Twist Drills  

Science Conference Proceedings (OSTI)

Despite of the attractive advantage of applying diamond coating to drills, ... Investigation of a Hybrid Cutting Tool Design for Shearing Operations of Sheet Metals.

369

NREL: Technology Transfer - Apply Now for Energy-Efficient Housing ...  

Apply Now for Energy-Efficient Housing ... and NREL's Residential Buildings Research Web site to learn about systems integration and energy analysis ...

370

1 SCRA Applied Research & Development offers the following ...  

Science Conference Proceedings (OSTI)

... and the rapid transition of results into US ... the Way (PLTW); National Science Foundation initiatives ... 6 SCRA Applied R&D 5300 International Blvd N ...

2012-10-26T23:59:59.000Z

371

Applied Process Engineering Laborotory APEL | Open Energy Information  

Open Energy Info (EERE)

Engineering Laborotory APEL Jump to: navigation, search Name Applied Process Engineering Laborotory (APEL) Place United States Sector Services Product General Financial & Legal...

372

Applied Mathematics and Plasma Physics, T-5: Theoretical, T:...  

NLE Websites -- All DOE Office Websites (Extended Search)

Pieter Swart Deputy Group Leader Kim Rasmussen Administration Charlotte Lehman Office Location TA-3, Bldg 508, Rm 204 Applied Mathematics and Plasma Physics, T-5 The group...

373

Mark Linne Dept. Applied Mechanics, Chalmers University, Gothenburg...  

NLE Websites -- All DOE Office Websites (Extended Search)

Optical and X-ray Measurements for Fuel Sprays Mark Linne Dept. Applied Mechanics, Chalmers University, Gothenburg, 41296, Sweden This talk will describe measurement needs across...

374

An improved Benders decomposition applied to a multi-layer ...  

E-Print Network (OSTI)

GLOBECOM 2007, Washington DC, USA, December 2007. [8] A. M. Costa, A survey on benders decomposition applied to fixed-charge network design...

375

Infrared Imagery Applied to A Large Buoyant Plume  

Science Conference Proceedings (OSTI)

The possibility of applying infrared imagery to the study of a large, hot plume materialized by carbon particles resulting from the incomplete combustion of fuel oil is investigated.

J-M. Brustet; B. Benech; P. Waldteufel

1981-05-01T23:59:59.000Z

376

Steel Research Applied to National Needs - A Company Perspective  

Science Conference Proceedings (OSTI)

Symposium, Materials Research Applied to National Needs (MARANN) in Honor of ... food packaging, transportation (auto, rail, and air), etc, to name just a few.

377

Geothermal: Sponsored by OSTI -- Extracting and Applying SV-SV...  

Office of Scientific and Technical Information (OSTI)

Extracting and Applying SV-SV Shear Modes from Vertical Vibrator Data Across Geothermal Prospects Final Report Geothermal Technologies Legacy Collection HelpFAQ | Site Map |...

378

Lagrangean Duality Applied on Vehicle Routing with Time Windows  

E-Print Network (OSTI)

Nov 6, 2001 ... Lagrangean Duality Applied on Vehicle Routing with Time Windows ... with the Vehicle Routing Problem with Time Windows (VRPTW).

379

Los Alamos Lab: International and Applied Technology Division...  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Electromagnetics, IAT-2 IAT-2 is a broad spectrum electromagnetics applications organization whose research and development activities address the Global Security...

380

How to Apply for NIST, Department of Commerce, and Other ...  

Science Conference Proceedings (OSTI)

... Search for Job Vacancies: Vacancy announcements contain important information that applicants need to know to apply for a specific job opening ...

2013-08-09T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Modular Systems Biology applied to TGFbeta and DNA Damage Response...  

NLE Websites -- All DOE Office Websites (Extended Search)

Modular Systems Biology applied to TGFbeta and DNA Damage Response Signaling following Low Dose Radiation Francis Cucinotta NASA Johnson Space Center Abstract Modular systems...

382

Microsoft PowerPoint - FinalModule5.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5: EVMS Concepts and Methods 5: EVMS Concepts and Methods Prepared by: Module 5 - EVMS Concepts and Methods 1 Prepared by: Booz Allen Hamilton Module 5: EVMS Concepts and Methods Welcome to Module 5. The objective of this module is to introduce you to Basic Earned Value concepts and methods. The Topics that will be addressed in this Module include: * Earned Valve Management System (EVMS) Criteria * The definitions and illustrations of the basic EVMS terminology * The definition and illustrations of the EV methods Module 5 - EVMS Concepts and Methods 2 Prepared by: Booz Allen Hamilton Review of Previous Modules In the previous four modules, we discussed the framework needed to perform Earned Value and develop an Earned Value Management System (EVMS). * In Module 1 we introduced you to earned value and the requirements for

383

VME Data Acquisition Modules for MINERvA Experiment  

SciTech Connect

This document describes two VME modules developed for MINERvA experiment at Fermilab. The Chain ReadOut Controller (CROC) module has four serial data channels and can interface with up to 48 front-ends using standard CAT5e networking cable. The data transmission rate of each channel is 160 Mbit/s. The maximum data transmission rate via VME bus is {approx}18 MB/s. The Chain Readout Interface Module (CRIM) is designed to provide various interface functions for the CROC module. It is compatible with MINOS MTM timing module and can be used to distribute timing signals to four CROC modules. The CRIM module also has a data port compatible with the CROC serial data interface. The data port can be used for diagnostic purpose and can generate triggers from front-end events. The CRIM module is a standard D08(O) interrupter module.

Baldin, B.; /fermilab

2010-01-01T23:59:59.000Z

384

Categorical Exclusion Determinations: North Carolina | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

April 9, 2010 April 9, 2010 CX-001794: Categorical Exclusion Determination Commercial Renewable Energy Systems - Charlotte Mecklenburg School Solar Thermal CX(s) Applied: B5.1 Date: 04/09/2010 Location(s): Cornelius, North Carolina Office(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory April 8, 2010 CX-001635: Categorical Exclusion Determination Solar American Institute Incubator - Semprius - Massively Parallel Microcell-Based Module Array CX(s) Applied: B3.6 Date: 04/08/2010 Location(s): Durham, North Carolina Office(s): Energy Efficiency and Renewable Energy, Golden Field Office April 7, 2010 CX-001432: Categorical Exclusion Determination Commercial Renewable Energy Systems - Gaston County Solid Waste Biogas Project CX(s) Applied: B1.15, A9, A11, B5.1

385

Categorical Exclusion (CX) Determinations By Date | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

25, 2010 25, 2010 CX-004445: Categorical Exclusion Determination Waste Treatment Plant Secondary Waste Radioactive Fluidized Bed Steam Reforming (Module A) CX(s) Applied: B3.6 Date: 10/25/2010 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office October 25, 2010 CX-004349: Categorical Exclusion Determination Near Zero Carbon Footprint Energy Creation through Thermal Oxidation CX(s) Applied: A9, B3.6 Date: 10/25/2010 Location(s): Allentown, Pennsylvania Office(s): Energy Efficiency and Renewable Energy, Golden Field Office October 25, 2010 CX-004332: Categorical Exclusion Determination Geothermal Incentive Program - Old Lyme High School Geothermal CX(s) Applied: A9, B5.1 Date: 10/25/2010 Location(s): Old Lyme, Connecticut Office(s): Energy Efficiency and Renewable Energy, National Energy

386

Categorical Exclusion Determinations: Environmental Management | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

September 23, 2010 September 23, 2010 CX-004179: Categorical Exclusion Determination Bench Scale Testing on the Cesium Nitric Acid Recovery Evaporator (CNP) CX(s) Applied: B3.6 Date: 09/23/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office September 23, 2010 CX-004177: Categorical Exclusion Determination Waste Treatment Plant Secondary Waste Radioactive Bench-Scale Steam Reformer (Module A) CX(s) Applied: B3.6 Date: 09/23/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office September 23, 2010 CX-004176: Categorical Exclusion Determination Making Nepheline (NaAlSiO4), Phase Pure Standards CX(s) Applied: B3.6 Date: 09/23/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office

387

Categorical Exclusion Determinations: Office of Energy Efficiency and  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0, 2010 0, 2010 CX-001718: Categorical Exclusion Determination Purchase and Installation of a Geothermal Power Plant Module, Heat Exchanger and Cooling Tower System to Generate Electricity Using Geothermal Water Resources CX(s) Applied: A9, B5.1, B5.2 Date: 04/20/2010 Location(s): Klamath Falls, Oregon Office(s): Energy Efficiency and Renewable Energy, Golden Field Office April 20, 2010 CX-001848: Categorical Exclusion Determination Michigan-Tribe-Nottawaseppi Huron Band of the Potawatomi CX(s) Applied: A9, B5.1 Date: 04/20/2010 Location(s): Michigan Office(s): Energy Efficiency and Renewable Energy April 20, 2010 CX-001748: Categorical Exclusion Determination Alaska-Tribe-Cook Inlet Region, Incorporated CX(s) Applied: A9, A11, B2.5, B5.1 Date: 04/20/2010 Location(s): Alaska

388

Categorical Exclusion (CX) Determinations By Date | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5, 2010 5, 2010 CX-002776: Categorical Exclusion Determination California-City-Elk Grove CX(s) Applied: B2.5, A9, A11, B5.1 Date: 06/15/2010 Location(s): Elk Grove, California Office(s): Energy Efficiency and Renewable Energy June 15, 2010 CX-002757: Categorical Exclusion Determination Drill One Exploratory Borehole on Lease Tract 15A by Golden Eagle Uranium CX(s) Applied: B3.1, B1.3 Date: 06/15/2010 Location(s): San Miguel County, Colorado Office(s): Legacy Management June 15, 2010 CX-002775: Categorical Exclusion Determination Bridgeport Indian Colony of California CX(s) Applied: B2.5, B5.1 Date: 06/15/2010 Location(s): California Office(s): Energy Efficiency and Renewable Energy June 15, 2010 CX-002697: Categorical Exclusion Determination High Fidelity Multi-Phase Radiation Module for Modern Coal Combustion

389

Categorical Exclusion Determinations: Savannah River Operations Office |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

October 25, 2010 October 25, 2010 CX-004445: Categorical Exclusion Determination Waste Treatment Plant Secondary Waste Radioactive Fluidized Bed Steam Reforming (Module A) CX(s) Applied: B3.6 Date: 10/25/2010 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office October 15, 2010 CX-004450: Categorical Exclusion Determination Plutonium Glass Sectioning CX(s) Applied: B3.6 Date: 10/15/2010 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office October 15, 2010 CX-004449: Categorical Exclusion Determination Bench Scale Testing to Provide Data on Precipitation Control in the Cesium Nitric Acid Recovery Process CX(s) Applied: B3.6 Date: 10/15/2010 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office October 15, 2010

390

Categorical Exclusion Determinations: Ohio | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

August 26, 2010 August 26, 2010 CX-003536: Categorical Exclusion Determination High-Bandwidth Modulation of Hydrogen/Syngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08/26/2010 Location(s): Mentor, Ohio Office(s): Fossil Energy, National Energy Technology Laboratory August 26, 2010 CX-003530: Categorical Exclusion Determination Zero Carbon Impact Vehicle and Photovoltaic Array CX(s) Applied: A1, A9, B1.3, B5.1 Date: 08/26/2010 Location(s): Lorain County, Ohio Office(s): Electricity Delivery and Energy Reliability, National Energy Technology Laboratory August 26, 2010 CX-003529: Categorical Exclusion Determination Substation Preventive Maintenance Program CX(s) Applied: A1, A9, B1.3, B5.1 Date: 08/26/2010 Location(s): Ottawa, Ohio Office(s): Electricity Delivery and Energy Reliability, National Energy

391

General Renewable Energy Technology Module | Open Energy Information  

Open Energy Info (EERE)

General Renewable Energy Technology Module General Renewable Energy Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: General Renewable Energy Technology Module Agency/Company /Organization: World Bank Sector: Energy Focus Area: Renewable Energy Topics: Technology characterizations Website: web.worldbank.org/WBSITE/EXTERNAL/TOPICS/EXTENERGY2/EXTRENENERGYTK/0,, References: General Renewable Energy Technology Module[1] Resource Generation and Transmission Interconnection Process Overview, PJM Manual, Transmission and Interconnection Planning Department, System Planning Division, PJM Interconnection, LLC References ↑ "General Renewable Energy Technology Module" Retrieved from "http://en.openei.org/w/index.php?title=General_Renewable_Energy_Technology_Module&oldid=328701

392

urbino worldwide campus applied computer scienceComputer Architecture  

E-Print Network (OSTI)

urbino worldwide campus applied computer scienceComputer Architecture alessandro bogliolo isti information science and technology institute 1/16 05.03 Pipeline hazards 05 CPU 05.03 Pipeline hazards;urbino worldwide campus applied computer scienceComputer Architecture alessandro bogliolo isti

Bogliolo, Alessandro

393

Applying to EPA for Approval of Other Uses of Phosphogypsum  

E-Print Network (OSTI)

Applying to EPA for Approval of Other Uses of Phosphogypsum: Preparing and Submitting a Complete. EP-D-04-007, Work Assignment 0-2 December 2005 #12;ii Applying for Other Uses of Phosphogypsum phosphogypsum in stacks? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.4. What

394

Drilling Waste Management Technology Identification Module  

NLE Websites -- All DOE Office Websites (Extended Search)

you are in this section Technology Identification you are in this section Technology Identification Home » Technology Identification Drilling Waste Management Technology Identification Module The Technology Identification Module is an interactive tool for identifying appropriate drilling waste management strategies for a given well location and circumstances. The Technology Identification Module follows the philosophy of a waste management hierarchy. Waste management options with the lowest environmental impacts are encouraged ahead of those with more significant environmental impacts. The Technology Identification Module helps identify waste management options, but users should also consider their own site-specific costs and waste volumes. How it Works Users will be asked to answer a series of questions about the location of the well site, physical features of the site that may allow or inhibit the use of various options, whether the regulatory agency with jurisdiction allows or prohibits particular options, and whether cost or the user's company policy would preclude any options. Nearly all questions are set up for only "yes" or "no" responses. Depending on how the initial questions are answered, users will face from 15 to 35 total questions. Some of these can be answered immediately, while others may require some additional investigation of other portions of this web site or external information. Suitable options will be identified as users complete the questions, and users will be able to print out a summary of suitable options when the process is completed.

395

Module Allocation for Dynamically Reconfigurable Systems  

Science Conference Proceedings (OSTI)

The synthesis of dynamically reconfigurable systems poses some new challenges for high-level synthesis tools. In this paper, we deal with the task of module allocation as this step has a direct influence on the performance of the dynamically reconfigudreasbiglne. ...

Xue-Jie Zhang; Kam-Wing Ng

2000-05-01T23:59:59.000Z

396

Biotech Nano Name School Email Address Module  

E-Print Network (OSTI)

Biotech Nano Name School Email Address Module Ajlouni, Leen Y American Community School Amman leen_ajlouni@hotmail.com Biotech Nano Jordan ajlouniyas@gmail.com Anupindi, Arusha Academy for Science & Design aaofnda@gmail.com Biotech Nano greet_hello@yahoo.com hellosmartboy@gmail.com Bourque, Mary Bangor High School maryebourque

397

Light modulated switches and radio frequency emitters  

DOE Patents (OSTI)

The disclosure relates to a light modulated electron beam driven radiofrequency emitter. Pulses of light impinge on a photoemissive device which generates an electron beam having the pulse characteristics of the light. The electron beam is accelerated through a radiofrequency resonator which produces radiofrequency emission in accordance with the electron, hence, the light pulses.

Wilson, Mahlon T. (Los Alamos, NM); Tallerico, Paul J. (Los Alamos, NM)

1982-01-01T23:59:59.000Z

398

Light modulated electron beam driven radiofrequency emitter  

DOE Patents (OSTI)

The disclosure relates to a light modulated electron beam-driven radiofrequency emitter. Pulses of light impinge on a photoemissive device which generates an electron beam having the pulse characteristics of the light. The electron beam is accelerated through a radiofrequency resonator which produces radiofrequency emission in accordance with the electron, hence, the light pulses.

Wilson, M.T.; Tallerico, P.J.

1979-10-10T23:59:59.000Z

399

Heat Shock Response Modulators as Therapeutic  

E-Print Network (OSTI)

Heat Shock Response Modulators as Therapeutic Tools for Diseases of Protein Conformation* Published shock tran- scription factor 1 (HSF1), the master stress-inducible regulator, and our current understanding of pharmacologically active small molecule regu- lators of the heat shock response

Morimoto, Richard

400

Final PV module degradation-analysis report  

DOE Green Energy (OSTI)

Visual and electrical degradation analyses were performed on 47 modules from: the Natural Bridges National Monument (NBNM) in Utah; Massachusetts Institute of Technology (MIT) in Cambridge, Massachusetts; and the University of Nebraska at Mead, Nebraska. Such problems as discoloration, cracking, scratches, and electrical degradation were detected. (LEW)

Themelis, M P

1982-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Module Technology: Current Practice and Issues (Presentation)  

DOE Green Energy (OSTI)

PV modules must provide mechanical support for the cells, protect the world from the voltages inside, protect the cells, diodes and interconnects from the weather outside, couple as much light as possible into the PV cells and minimize the temperature increase of the cells. The package must continue to serve these functions for at least 25 years as that is the typical module warranty period today. Furthermore the package must do all this for as low a cost as possible since the key to large scale PV growth is a reduction in cost while retaining excellent module reliability and durability. This paper will review current module construction practices for both crystalline silicon and thin film PV with emphasis on explaining why the present designs and materials have been selected. Possible long term issues with today's designs and materials will be discussed. Several proposed solutions to these issues will be presented, highlighting the research efforts that will be necessary in order to verify that they can cost effectively solve the identified issues.

Wohlgemuth, J.

2010-10-05T23:59:59.000Z

402

Applied Mathematics | U.S. DOE Office of Science (SC)  

Office of Science (SC) Website

Applied Applied Mathematics Advanced Scientific Computing Research (ASCR) ASCR Home About Research Applied Mathematics Applied Mathematics Conferences And Workshops Computer Science Next Generation Networking Scientific Discovery through Advanced Computing (SciDAC) Computational Science Graduate Fellowship (CSGF) ASCR SBIR-STTR Facilities Science Highlights Benefits of ASCR Funding Opportunities Advanced Scientific Computing Advisory Committee (ASCAC) News & Resources Contact Information Advanced Scientific Computing Research U.S. Department of Energy SC-21/Germantown Building 1000 Independence Ave., SW Washington, DC 20585 P: (301) 903-7486 F: (301) 903-4846 E: sc.ascr@science.doe.gov More Information » Research Applied Mathematics Print Text Size: A A A RSS Feeds FeedbackShare Page

403

Remediation of Mercury and Industrial Contaminants Applied Field Research  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Remediation of Mercury and Industrial Contaminants Applied Field Remediation of Mercury and Industrial Contaminants Applied Field Research Initiative (RoMIC-AFRI) Remediation of Mercury and Industrial Contaminants Applied Field Research Initiative (RoMIC-AFRI) Remediation of Mercury and Industrial Contaminants Applied Field Research Initiative (RoMIC-AFRI) Located on the Oak Ridge Reservation (ORR) in Oak Ridge, Tennessee, the RoMIC-AFRI was established to protect water resources by addressing the challenge of preventing contamination. The initiative at Oak Ridge is a collaborative effort that leverages DOE investments in basic science and applied research and the work of site contractors to address the complex challenges in the remediation of legacy waste at the Oak Ridge Reservation. The mission of the Remediation of Mercury and Industrial Contaminants

404

Applied Materials Switzerland SA Formerly HCT Shaping Systems SA | Open  

Open Energy Info (EERE)

Switzerland SA Formerly HCT Shaping Systems SA Switzerland SA Formerly HCT Shaping Systems SA Jump to: navigation, search Name Applied Materials Switzerland SA (Formerly HCT Shaping Systems SA) Place Chezeaux, Switzerland Zip 1033 Product Manufacturer of wire saws for the semiconductor and photovoltaic wafer slicing industries. References Applied Materials Switzerland SA (Formerly HCT Shaping Systems SA)[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Applied Materials Switzerland SA (Formerly HCT Shaping Systems SA) is a company located in Chezeaux, Switzerland . References ↑ "[ Applied Materials Switzerland SA (Formerly HCT Shaping Systems SA)]" Retrieved from "http://en.openei.org/w/index.php?title=Applied_Materials_Switzerland_SA_Formerly_HCT_Shaping_Systems_SA&oldid=342245"

405

Research on high-efficiency, large-area, CuInSe{sub 2}-based thin- film modules. Annual subcontract report, 1 May 1992--15 Aug 1993  

DOE Green Energy (OSTI)

This report describes work to demonstrate 12.5% aperture efficient, large-area (3900-cm{sup 2}) encapsulated thin-film CuInSe{sub 2} (CIS) photovoltaic modules. Module design consists of 53 series-connected ZnO/CdS/CIS/Mo/glass cells fabricated on a 4141-cm{sup 2} (128.6 {times} 32.2 cm) glass substrate with a nominal aperture area of 3895 cm{sup 2} (127.3 {times} 30.6 cm). Four CIS modules were shipped to NREL under the terms of the subcontract. Phase 2 consisted of fabricating large-area (3900-cm{sup 2}) modules for high-performance module processing. The large-area parts proved to be cumbersome, and we decided to use smaller substrates (100 cm{sup 2}) to accelerate the progress in solving the types of technical challenges that were discovered in processing large-area parts, and then to apply these solutions to larger areas to meet the objectives of the investigation. Most critical issues determining module yield losses can be grouped into three major categories: (1) Uniformity and reproducibility of the absorber formation process dominates the fundamental performance of the material over a large area, (2) interaction of the substrate with the Mm requires appropriate selection criterial and preparation techniques for minimizing defects that lead to shunting and areas of poor photoresponse, and (3) performance losses near interconnects reduce module performance and can cause inadequate performance through module durability testing.

Knapp, K.E.; Gay, R.R. [Siemens Solar Industries, Camarillo, CA (United States)

1994-01-01T23:59:59.000Z

406

Klystron Modulator Design for the Los Alamos Neutron Science Center Accelerator  

SciTech Connect

This paper will describe the design of the 44 modulator systems that will be installed to upgrade the Los Alamos Neutron Science Center (LANSCE) accelerator RF system. The klystrons can operate up to 86 kV with a nominal 32 Amp beam current with a 120 Hz repetition rate and 15% duty cycle. The klystrons are a mod-anode design. The modulator is designed with analog feedback control to ensure the klystron beam current is flat-top regulated. To achieve fast switching while maintaining linear feedback control, a grid-clamp, totem-pole modulator configuration is used with an 'on' deck and an 'off' deck. The on and off deck modulators are of identical design and utilize a cascode connected planar triode, cathode driven with a high speed MOSFET. The derived feedback is connected to the planar triode grid to enable the flat-top control. Although modern design approaches suggest solid state designs may be considered, the planar triode (Eimac Y-847B) is very cost effective, is easy to integrate with the existing hardware, and provides a simplified linear feedback control mechanism. The design is very compact and fault tolerant. This paper will review the complete electrical design, operational performance, and system characterization as applied to the LANSCE installation.

Reass, William A. [Los Alamos National Laboratory; Baca, David M. [Los Alamos National Laboratory; Partridge, Edward R. [retired; Rees, Daniel E. [Los Alamos National Laboratory

2012-06-22T23:59:59.000Z

407

Standard Test Methods for Insulation Integrity and Ground Path Continuity of Photovoltaic Modules  

E-Print Network (OSTI)

1.1 These test methods cover procedures for (1) testing for current leakage between the electrical circuit of a photovoltaic module and its external components while a user-specified voltage is applied and (2) for testing for possible module insulation breakdown (dielectric voltage withstand test). 1.2 A procedure is described for measuring the insulation resistance between the electrical circuit of a photovoltaic module and its external components (insulation resistance test). 1.3 A procedure is provided for verifying that electrical continuity exists between the exposed external conductive surfaces of the module, such as the frame, structural members, or edge closures, and its grounding point (ground path continuity test). 1.4 This test method does not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of this test method. 1.5 There is no similar or equivalent ISO standard. This standard does not purport to address all of the safety concerns, if a...

American Society for Testing and Materials. Philadelphia

2000-01-01T23:59:59.000Z

408

Method and apparatus for pulse width modulation control of an AC induction motor  

SciTech Connect

An inverter is connected between a source of DC power and a three-phase AC induction motor, and a micro-processor-based circuit controls the inverter using pulse width modulation techniques. In the disclosed method of pulse width modulation, both edges of each pulse of a carrier pulse train are equally modulated by a time proportional to sin .THETA., where .THETA. is the angular displacement of the pulse center at the motor stator frequency from a fixed reference point on the carrier waveform. The carrier waveform frequency is a multiple of the motor stator frequency. The modulated pulse train is then applied to each of the motor phase inputs with respective phase shifts of 120.degree. at the stator frequency. Switching control commands of electronic switches in the inverter are stored in a random access memory (RAM) and the locations of the RAM are successively read out in a cyclic manner, each bit of a given RAM location controlling a respective phase input of the motor. The DC power source preferably comprises rechargeable batteries and all but one of the electronic switches in the inverter can be disabled, the remaining electronic switch being part of a "flyback" DC-DC converter circuit for recharging the battery.

Geppert, Steven (Bloomfield Hills, MI); Slicker, James M. (Union Lake, MI)

1984-01-01T23:59:59.000Z

409

Microsoft PowerPoint - FinalModule6.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6: Metrics, Performance 6: Metrics, Performance Measurements and Forecasting Prepared by: Module 6 - Metrics, Performance Measures and Forecasting 2 Prepared by: Booz Allen Hamilton Module 6: Metrics, Performance Measurements and Forecasting Welcome to Module 6. The objective of this module is to introduce you to the Metrics and Performance Measurement tools used, along with Forecasting, in Earned Value Management. The Topics that will be addressed in this Module include: * Define Cost and Schedule Variances * Define Cost and Schedule Performance Indices * Define Estimate to Complete (ETC) * Define Estimate at Completion (EAC) and Latest Revised Estimate (LRE) Module 6 - Metrics, Performance Measures and Forecasting 3 Prepared by: Booz Allen Hamilton Review of Previous Modules Let's quickly review what has been covered in the previous modules.

410

Microsoft PowerPoint - FinalModule7.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7: Integrated Baseline Review 7: Integrated Baseline Review and Change Control Prepared by: Module 7 - Integrated Baseline Review and Change Control 1 Prepared by: Booz Allen Hamilton Module 7: Integrated Baseline Review and Change Control Welcome to Module 7. The objective of this module is to introduce you to the concepts of the Integrated Baseline Review Process and requirements for Change Control. The Topics that will be addressed in this Module include: * Definition of an Integrated Baseline Review (IBR) * Integrated Baseline Review Objectives and Responsibilities * Change Control Process Module 7 - Integrated Baseline Review and Change Control 2 Prepared by: Booz Allen Hamilton Review of Previous Modules To review some critical terminology and define the framework within which IBRs are conducted, let's look back at the previous six modules.

411

A PRECISION PROGRAMMABLE BIPOLAR V/f INSTRUMENTATION MODULE  

E-Print Network (OSTI)

O R M A L BIPOLAR V/f INSTRUMENTATION MODULE* R G A M B E W.PROGRAMMABLE BIPOLAR V / f INSTRUMENTATION MODULE W.E. H e a

Hearn, W.E.

2010-01-01T23:59:59.000Z

412

Renewable Fuels Module, Appendix - Model Performance, Model Documentation  

Reports and Publications (EIA)

This appendix discusses performance aspects of the Renewable Fuels Module (RFM). It is intended to present the pattern of response of the RFM to typical changes in its major inputs from other NEMS modules.

Perry M. Lindstrom

1995-06-01T23:59:59.000Z

413

Polycrystalline thin-film module and system performance  

DOE Green Energy (OSTI)

The Module and System Performance and Engineering Project at the National Renewable Energy Laboratory (NREL) conducts in-situ technical evaluations of photovoltaic (PV) modules and systems (arrays). These evaluations on module/array performance and stability are conducted at the NREL Photovoltaic Outdoor Test Facility (OTF) in Golden, CO. The modules and arrays are located at 39.7{degree}N latitude, 105.2{degree}W longitude, and at 1,782 meters elevation. Currently, two polycrystalline thin-film technologies are the focus of the research presented here. The module structures are copper indium diselenide (CIS) from Siemens Solar Industries and cadmium telluride (CdTe) from Solar Cells, Inc. The research team is attempting to correlate individual module performance with array performance for these two polycrystalline thin-film technologies. This is done by looking at module and array performance over time. Also, temperature coefficients are determined at both the module and array level. Results are discussed.

Strand, T.; Kroposki, B.; Hansen, R.; Mrig, L.

1995-11-01T23:59:59.000Z

414

Viscoelastic properties of seed cotton and their effect on module shape and density  

E-Print Network (OSTI)

Modules for cotton storage and transport should be constructed with a shape that will resist collecting water to maintain the quality of seed cotton during storage. Meeting this specification requires knowledge of the relationship between the applied compressive force, deformation, and time for seed cotton. Several factors were tested to determine their effects on the height and density of seed cotton during compression, creep loading, and recovery. Models were used to describe these processes. These results were used to develop an algorithm capable of providing information on module shape to the module builder operator. The initial loading density did not affect the compressed density, but a slight effect was observed in the recovered density, due to the weight of the seed cotton. Picker harvested cotton was compressed to a greater density than stripper harvested cotton, but expanded more during recovery, resulting in similar final densities. Multiple compressions increased the density, but this increase was not physically significant after the third compression. Higher moisture content increased the density seed cotton could be compressed to slightly. Viscoelastic behavior was observed; however, the effect on density was small. Both the compression and creep curves were described using mathematical models. A compression model using an asymptotic true strain measure yielded high R2 values; however, some aspect of this process remained unexplained and the equation was limited in its predictive ability. Creep behavior was described using a modified Burgers model. This model was more accurate than the creep model, although a definite trend existed in the creep model residuals. A feedback algorithm was developed based on the observation that the compressed density was primarily dependent on the mass of seed cotton and not the initial density. By measuring the compressed depth of cotton in a module and the hydraulic pressure of the tramper foot cylinder, the resulting shape of the module can be predicted. Improved loading of the module builder is necessary to produce a desirably shaped module. More seed cotton needs to be placed in the center of the module, resulting in a surface that slopes down towards the outer edges.

Hardin, Robert Glen

2004-08-01T23:59:59.000Z

415

Residential Demand Module of the National Energy Modeling ...  

U.S. Energy Information Administration (EIA)

Residential Demand Module of the National Energy Modeling System: Model Documentation 2013 November 2013 Independent Statistics & Analysis ...

416

Integrating Module of the National Energy Modeling System ...  

U.S. Energy Information Administration (EIA)

Chapter 3 describes the NEMS global data structure, used for inter-module communication, ... technologies, representations of renewable energy technologies, ...

417

Industrial Demand Module (IDM) - 2002 EIA Models Directory  

U.S. Energy Information Administration (EIA)

The Industrial Demand Module incorporates three components: buildings; process and assembly; and boiler, steam, and cogeneration. Last Model Update:

418

SLAC 16-channel differential TTL output module (Engineering Materials)  

SciTech Connect

The drawings listed on the Drawing List provide the data and specifications for constructing a SLAC 16-channel differential TTL output module as used in the SLAC PEP storage ring instrumentation and control system. It is a CAMAC module used as an output interface module from CAMAC signals.

Not Available

1983-04-05T23:59:59.000Z

419

Integrating Module of the National Energy Modeling System  

Reports and Publications (EIA)

Provides an overview of the complete National Energy Modeling System (NEMS) model, and includes brief descriptions of the modules with which the Integrating Module interacts. The emphasis and focus, however, is on the structure and function of the Integrating Module of NEMS.

Dan Skelly

2010-06-01T23:59:59.000Z

420

World Energy Projection System Plus (WEPS+): Global Activity Module  

Reports and Publications (EIA)

World Energy Projection System Plus Model Documentation: Global Activity Module Documents the objectives, analytical approach, and development of the World Energy Projection Plus (WEPS+) Global Activity Module (GAM) used to develop the International Energy Outlook for 2013 (IEO2013). The report catalogues and describes the module assumptions, computations, methodology, parameter estimation techniques, and mainframe source code

Vipin Arora

2013-10-23T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Solitary Alfven wave envelopes and the modulational instability  

SciTech Connect

The derivative nonlinear Schroedinger equation describes the modulational instability of circularly polarized dispersive Alfven wave envelopes. It also may be used to determine the properties of finite amplitude localized stationary wave envelopes. Such envelope solitons exist only in conditions of modulational stability. This leaves open the question of whether, and if so, how, the modulational instability produces envelope solitons. 12 refs.

Kennel, C.F.

1987-06-01T23:59:59.000Z

422

Tree image growth analysis using instantaneous phase modulation  

Science Conference Proceedings (OSTI)

We propose the use of Amplitude-Modulation Frequency-Modulation (AM-FM) methods for tree growth analysis. Tree growth is modeled using phase modulation. For adapting AM-FM methods to different images, we introduce the use of fast filterbank filter coefficient ...

Janakiramanan Ramachandran; Marios S. Pattichis; Louis A. Scuderi; Justin S. Baba

2011-01-01T23:59:59.000Z

423

How to Apply for Senior Executive positions | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How to Apply for Senior Executive positions How to Apply for Senior Executive positions How to Apply for Senior Executive positions To apply vacancies for SENIOR EXECUTIVE SERVICE (SES) , SENIOR LEVEL (SL), SCIENTIFIC AND PROFESSIONAL (ST) positions within the Department of Energy please visit OPM's website: http://www.usajobs.gov. From this site, you may download announcements for vacancies of interest to you. SENIOR EXECUTIVE SERVICE (SES) The Guide to Senior Executive Service Qualifications provides detailed information about executive qualifications and tips for writing effective qualification statements. What Are Executive Core Qualifications (ECQs) The Executive Core Qualifications (ECQs) define the competencies needed to build a federal corporate culture that drives for results, serves customers, and builds successful teams and coalitions within and outside

424

Energy Efficiency in Buildings in Switzerland - Applied Research...  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Efficiency in Buildings in Switzerland - Applied Research on Vacuum Insulation, Passive Houses etc. Speaker(s): Armin Binz Date: January 21, 2003 - 12:00pm Location: Bldg....

425

Electrical capacitance volume tomography (ECVT) applied to bubbling fluid beds  

SciTech Connect

These presentation visuals illustrate the apparatus and method for applying Electrical Capacitance Volume Tomography (ECVT) to bubbling fluid beds to their solid fraction and bubble properties. Results are compared to estimated values.

Weber, J., Mei, J.

2012-01-01T23:59:59.000Z

426

A Stereo Photogrammetric Technique Applied to Orographic Convection  

Science Conference Proceedings (OSTI)

This paper describes a technique for photogrammetric analysis of stereo pairs of images that is applied to the study of orographic convection. The technique is designed for use with digital images and assumes detailed knowledge of the camera ...

Joseph A. Zehnder; Jiuxiang Hu; Anshuman Razdan

2007-06-01T23:59:59.000Z

427

Proceedings of the 2008 ACM symposium on Applied computing  

Science Conference Proceedings (OSTI)

Welcome to the 23rd Annual ACM Symposium on Applied Computing (SAC 2008). This international event is dedicated to computer scientists, engineers, and practitioners seeking innovative ideas in various areas of computer applications. This year, the conference ...

Roger L. Wainwright; Hisham M. Haddad

2008-03-01T23:59:59.000Z

428

DOE Solar Decathlon: How to Apply for the Solar Decathlon  

NLE Websites -- All DOE Office Websites (Extended Search)

Photos Videos Education Sponsors Volunteers History FAQs Contacts How To Apply for the Solar Decathlon Is your school interested in participating in the next U.S. Department of...

429

NEW MOTOR DESIGN CONCEPT FOR ENERGY SAVING APPLIED TO  

E-Print Network (OSTI)

SHARK, NEW MOTOR DESIGN CONCEPT FOR ENERGY SAVING APPLIED TO SWITCHED RELUCTANCE MOTOR by Ana of the cylindrical and Shark air gap Switched Reluctance Motors and their assistance during the experimental work with other motor technologies such

430

Los Alamos Lab: International and Applied Technology Division...  

NLE Websites -- All DOE Office Websites (Extended Search)

International Research and Analysis, IAT-1 IAT-1 has one of the most diverse work forces in the division. By applying its scientific and engineering skills to designated problems,...

431

Proceedings of the 2009 ACM symposium on Applied Computing  

Science Conference Proceedings (OSTI)

On behalf of the Organizing Committee, we welcome you to the 24th Annual ACM Symposium on Applied Computing (SAC 2009) hosted by Chaminade University in Hawaii. This international forum has been dedicated to computer scientists, engineers and practitioners ...

Sung Y. Shin; Sascha Ossowski

2009-03-01T23:59:59.000Z

432

Microsoft Word - CPARS Web Based Training Modules  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

March 2010 1 March 2010 1 There are 5 web based training modules for Contractor Performance Assessment Reporting System (CPARS), Architect-Engineer Contract Administration Support Systems (ACASS), and Construction Contractor Appraisal Support System (CCASS). This on-line web based training is an interactive online classroom for the delivery of live training. There is no investment in software required. Web based training classes and the schedule for CPARS, ACASS, and CCASS classes are at http://www.cpars.csd.disa.mil/allapps/cpartrng/webtrain/webtrain_all.htm. The modules are as follows: 1 - ACASS/CCASS Overview (2 hours) (1 Continuous Learning Point) This training will give the student an overview of the policies and regulations governing ACASS/CCASS, the ACASS/CCASS Workflow, and ACASS/CCASS Application

433

Allosteric Modulation of DNA by Small Molecules  

NLE Websites -- All DOE Office Websites (Extended Search)

Allosteric Modulation of DNA by Small Allosteric Modulation of DNA by Small Molecules Signals originating at the cell surface are conveyed by a complex system of interconnected signaling pathways to the nucleus. They converge at transcription factors, which in turn regulate the transcription of sets of genes that result in the gene expression. Many human diseases are caused by dysregulated gene expression and the oversupply of transcription factors may be required for the growth and metastatic behavior of human cancers. Cell permeable small molecules that can be programmed to disrupt transcription factor-DNA interfaces could silence aberrant gene expression pathways. Pyrrole-imidazole polyamides are DNA minor groove binding small molecules that are programmable for a large repertoire of DNA motifs.

434

Strongly Coupled Striped Superconductor with Large Modulation  

E-Print Network (OSTI)

We analytically calculate properties of a strongly coupled striped superconductor, with the charge density wave sourced by a modulated chemical potential, in the large modulation wavenumber Q limit. In the absence of a homogeneous term in the chemical potential, we show that the critical temperature scales as a negative power of Q for scaling dimensions \\Delta 3/2, there is no phase transition above a certain critical value of Q. The condensate is found to scale as a positive power of Q such that the gap is proportional to Q. We discuss how these results change if a homogeneous term is added to the chemical potential. We compare our analytic results with numerical calculations whenever the latter are available and find good agreement.

Jimmy A. Hutasoit; Suman Ganguli; George Siopsis; Jason Therrien

2011-10-20T23:59:59.000Z

435

Natural Gas Transmission and Distribution Module  

Gasoline and Diesel Fuel Update (EIA)

page intentionally left blank page intentionally left blank 129 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Natural Gas Transmission and Distribution Module The NEMS Natural Gas Transmission and Distribution Module (NGTDM) derives domestic natural gas production, wellhead and border prices, end-use prices, and flows of natural gas through the regional interstate network, for both a peak (December through March) and off peak period during each projection year. These are derived by solving for the market equilibrium across the three main components of the natural gas market: the supply component, the demand component, and the transmission and distribution network that links them. Natural gas flow patterns are a function of the pattern in the previous year, coupled

436

Natural Gas Transmission and Distribution Module This  

Gasoline and Diesel Fuel Update (EIA)

This This page inTenTionally lefT blank 127 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Natural Gas Transmission and Distribution Module The NEMS Natural Gas Transmission and Distribution Module (NGTDM) derives domestic natural gas production, wellhead and border prices, end-use prices, and flows of natural gas through a regional interstate representative pipeline network, for both a peak (December through March) and off-peak period during each projection year. These are derived by solving for the market equilibrium across the three main components of the natural gas market: the supply component, the demand component, and the transmission and distribution network that links them. Natural gas flow patterns are a function of the

437

Materials Testing for PV Module Encapsulation  

DOE Green Energy (OSTI)

Important physical properties of materials used in PV module packaging are presented. High-moisture-barrier, high-resistivity, adhesion-promoting coatings on polyethyl-ene terephthalate (PET) films have been fabricated and characterized for use in PV module application and com-pared to standard polymer backsheet materials. Ethylene vinyl acetate (EVA) and an encapsulant replacement for EVA are studied for their water vapor transmission rate (WVTR) and adhesion properties. WVTR, at test conditions up to 85C/100% relative humidity (RH), and adhesion val-ues are measured before and after filtered xenon arc lamp ultraviolet (UV) exposure and damp heat exposure at 85C/85% RH. Water ingress is quantified by weight gain and embedded humidity sensors.

Jorgensen, G.; Terwilliger, K.; Glick, S.; Pern, J.; McMahon, T.

2003-05-01T23:59:59.000Z

438

Spin precession modulation in a magnetic bilayer  

Science Conference Proceedings (OSTI)

We report on modulation of the spin precession in a Co/garnet bilayer by femtosecond laser excitation using time-resolved magneto-optical tools. Damped oscillations in the Faraday rotation transients representing precessional motion of the magnetization vector are observed in both the 2 nm Co layer and 1.8 {mu}m garnet of the bilayer with distinct frequencies differing by about a factor of two. The excitation efficiency of these precessions strongly depends on the out-of-plane magnetic field. The modulation effect with the coupling in a magnetic bilayer can be useful for non-thermally controlling the magnetization of nanomagnets and ultrafast switching in magnetic nanodevices.

Stupakiewicz, A.; Maziewski, A. [Laboratory of Magnetism, Faculty of Physics, University of Bialystok, Lipowa 41, Bialystok (Poland); Pashkevich, M. [Laboratory of Magnetism, Faculty of Physics, University of Bialystok, Lipowa 41, Bialystok (Poland); Scientific-Practical Materials Research Centre of the NASB, P. Brovki 19, Minsk (Belarus); Stognij, A.; Novitskii, N. [Scientific-Practical Materials Research Centre of the NASB, P. Brovki 19, Minsk (Belarus)

2012-12-24T23:59:59.000Z

439

Modular Chemical Descriptor Language (MCDL): Stereochemical modules  

Science Conference Proceedings (OSTI)

In our previous papers we introduced the Modular Chemical Descriptor Language (MCDL) for providing a linear representation of chemical information. A subsequent development was the MCDL Java Chemical Structure Editor which is capable of drawing chemical structures from linear representations and generating MCDL descriptors from structures. In this paper we present MCDL modules and accompanying software that incorporate unique representation of molecular stereochemistry based on Cahn-Ingold-Prelog and Fischer ideas in constructing stereoisomer descriptors. The paper also contains additional discussions regarding canonical representation of stereochemical isomers, and brief algorithm descriptions of the open source LINDES, Java applet, and Open Babel MCDL processing module software packages. Testing of the upgraded MCDL Java Chemical Structure Editor on compounds taken from several large and diverse chemical databases demonstrated satisfactory performance for storage and processing of stereochemical information in MCDL format.

Gakh, Andrei A [ORNL; Burnett, Michael N [ORNL; Trepalin, Sergei V. [Institute Physiologically Active Compouds, Russian Academy of Sciences, Moscow; Yarkov, Alexander V [Institute Physiologically Active Compouds, Russian Academy of Sciences, Moscow

2011-01-01T23:59:59.000Z

440

Photovoltaic module with light reflecting backskin  

DOE Patents (OSTI)

A photovoltaic module comprises electrically interconnected and mutually spaced photovoltaic cells that are encapsulated by a light-transmitting encapsulant between a light-transparent front cover and a back cover, with the back cover sheet being an ionomer/nylon alloy embossed with V-shaped grooves running in at least two directions and coated with a light reflecting medium so as to provide light-reflecting facets that are aligned with the spaces between adjacent cells and oriented so as to reflect light falling in those spaces back toward said transparent front cover for further internal reflection onto the solar cells, whereby substantially all of the reflected light will be internally reflected from said cover sheet back to the photovoltaic cells, thereby increasing the current output of the module. The internal reflector improves power output by as much as 67%.

Gonsiorawski, Ronald C. (Danvers, MA)

2007-07-03T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Development of an Outdoor Concentrating Photovoltaic Module Testbed, Module Handling and Testing Procedures, and Initial Energy Production Results  

DOE Green Energy (OSTI)

This report addresses the various aspects of setting up a CPV testbed and procedures for handling and testing CPV modules.

Muller, M.

2009-09-01T23:59:59.000Z

442

18.337J / 6.338J Applied Parallel Computing (SMA 5505), Spring 2005  

E-Print Network (OSTI)

Applied Parallel Computing is an advanced interdisciplinary introduction to applied parallel computing on modern supercomputers.

Edelman, Alan

443

Solar Cell Modules With Improved Backskin  

SciTech Connect

A laminated solar cell module comprises a front light transmitting support, a plurality of interconnected solar cells encapsulated by a light-transmitting encapsulant material, and an improved backskin formed of an ionomer/nylon alloy. The improved backskin has a toughness and melting point temperature sufficiently great to avoid any likelihood of it being pierced by any of the components that interconnect the solar cells.

Gonsiorawski, Ronald C. (Danvers, MA)

2003-12-09T23:59:59.000Z

444

Positive modulator of bone morphogenic protein-2  

DOE Patents (OSTI)

Compounds of the present invention of formula I and formula II are disclosed in the specification and wherein the compounds are modulators of Bone Morphogenic Protein activity. Compounds are synthetic peptides having a non-growth factor heparin binding region, a linker, and sequences that bind specifically to a receptor for Bone Morphogenic Protein. Uses of compounds of the present invention in the treatment of bone lesions, degenerative joint disease and to enhance bone formation are disclosed.

Zamora, Paul O. (Gaithersburg, MD); Pena, Louis A. (Poquott, NY); Lin, Xinhua (Plainview, NY); Takahashi, Kazuyuki (Germantown, MD)

2009-01-27T23:59:59.000Z

445

Downhole drilling network using burst modulation techniques  

DOE Patents (OSTI)

A downhole drilling system is disclosed in one aspect of the present invention as including a drill string and a transmission line integrated into the drill string. Multiple network nodes are installed at selected intervals along the drill string and are adapted to communicate with one another through the transmission line. In order to efficiently allocate the available bandwidth, the network nodes are configured to use any of numerous burst modulation techniques to transmit data.

Hall; David R. (Provo, UT), Fox; Joe (Spanish Fork, UT)

2007-04-03T23:59:59.000Z

446

Square Butte HVDC modulation system field tests  

SciTech Connect

The authors describe field tests conducted at the Square Butte dc system to validate transfer functions of the digital model for dc current and voltage modulation control design. The field tests and digital model results confirm a dominant interarea mode of oscillation of 0.8 hz. Field tests also established spurious responses in rectifier and inverter frequency measurements which appear to be attributable to transducer distortion.

Grund, C.E. (General Electric Co., Schenectady, NY (USA)); Hauer, J.F. (BPA, Portland, OR (US)); Crane, L.P.; Carlson, D.L. (Minnesota Power and Light Co., Duluth, MN (USA)); Wright, S.E. (EPRI, Palo Alto, CA (US))

1990-01-01T23:59:59.000Z

447

Dust removal in radio-frequency plasmas by a traveling potential modulation  

Science Conference Proceedings (OSTI)

The dust contamination in plasma deposition processes plays a crucial role in the quality and the yield of the products. To improve the quality and the yield of plasma processing, a favorable way is to remove the dust particles actively from the plasma reactors.Our recent experiments in the striped electrode device show that a traveling plasma modulation allows for a systematic particle removal independent of the reactor size. Besides the rf powered electrode, the striped electrode device includes a segmented electrode that consists of 100 electrically insulated narrow stripes. A traveling potential profile is produced by the modulation of the voltage signals applied on the stripes. The dust particles are trapped in the potential wells and transported with the traveling of the potential profile.The particle-in-cell (PIC) simulation on the potential above the segmented electrode indicates that the traveling potential profile can be realized either by applying low-frequency (0.1-10 Hz) voltage signals with a fixed phase shift between adjacent stripes or high-frequency (10 kHz a circumflex AS 100 MHz) signals with the amplitudes modulated by a low-frequency envelope. The transportation of the dust particles is simulated with a two-dimensional molecular dynamics (MD) code with the potential profile obtained from the PIC simulation. The MD results reproduce the experimental observations successfully.This technology allows for an active removal of the contaminating particles in processing plasmas and it is independent of the reactor size. The removal velocity is controllable by adjusting the parameters for the modulation.

Li Yangfang; Jiang Ke; Thomas, Hubertus M.; Morfill, Gregor E. [Max-Planck-Institute for Extraterrestrial Physics, 85748 Garching (Germany)

2010-06-16T23:59:59.000Z

448

Wind Energy Technology Module | Open Energy Information  

Open Energy Info (EERE)

Wind Energy Technology Module Wind Energy Technology Module Jump to: navigation, search Tool Summary Name: Wind Energy Technology Module Agency/Company /Organization: World Bank Sector: Energy Focus Area: Renewable Energy, Wind Topics: Background analysis, Technology characterizations Website: web.worldbank.org/WBSITE/EXTERNAL/TOPICS/EXTENERGY2/EXTRENENERGYTK/0,, Country: Russia, China Eastern Europe, Eastern Asia Coordinates: 54.5283298°, 112.9648819° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":54.5283298,"lon":112.9648819,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

449

Low thermal resistance power module assembly  

DOE Patents (OSTI)

A power module assembly (400) with low thermal resistance and enhanced heat dissipation to a cooling medium. The assembly includes a heat sink or spreader plate (410) with passageways or openings (414) for coolant that extend through the plate from a lower surface (411) to an upper surface (412). A circuit substrate (420) is provided and positioned on the spreader plate (410) to cover the coolant passageways. The circuit substrate (420) includes a bonding layer (422) configured to extend about the periphery of each of the coolant passageways and is made up of a substantially nonporous material. The bonding layer (422) may be solder material which bonds to the upper surface (412) of the plate to provide a continuous seal around the upper edge of each opening (414) in the plate. The assembly includes power modules (430) mounted on the circuit substrate (420) on a surface opposite the bonding layer (422). The power modules (430) are positioned over or proximal to the coolant passageways.

Hassani, Vahab (Denver, CO); Vlahinos, Andreas (Castle Rock, CO); Bharathan, Desikan (Arvada, CO)

2010-12-28T23:59:59.000Z

450

Solar module having reflector between cells  

DOE Patents (OSTI)

A photovoltaic module comprising an array of electrically interconnected photovoltaic cells disposed in a planar and mutually spaced relationship between a light-transparent front cover member in sheet form and a back sheet structure is provided with a novel light-reflecting means disposed between adjacent cells for reflecting light falling in the areas between cells back toward said transparent cover member for further internal reflection onto the solar cells. The light-reflecting comprises a flexible plastic film that has been embossed so as to have a plurality of small V-shaped grooves in its front surface, and a thin light-reflecting coating on said front surface, the portions of said coating along the sides of said grooves forming light-reflecting facets, said grooves being formed so that said facets will reflect light impinging thereon back into said transparent cover sheet with an angle of incidence greater than the critical angle, whereby substantially all of the reflected light will be internally reflected from said cover sheet back to said solar modules, thereby increasing the current output of the module.

Kardauskas, Michael J. (Billerica, MA)

1999-01-01T23:59:59.000Z

451

SNS LINAC MODULATOR OPERATIONAL HISTORY AND PERFOMANCE  

Science Conference Proceedings (OSTI)

Fourteen High Voltage Converter Modulators (HVCM) were initially installed at the Spallation Neutron Source Linear Accelerator (SNS Linac) at the Oak Ridge National Laboratory in 2005. A fifteenth HVCM was added in 2009. Each modulator provides a pulse of up to 140 kV at a maximum width of 1.35 msec. Peak power level is 11 MW with an 8% duty factor. The HVCM system must be available for neutron production (NP) 24/7 with the exception being two, 6-week maintenance periods per year. HVCM reliability is one of the most important factors to maximize Linac availability and achieve SNS performance goals. During the last few years several modifications have been implemented to improve the overall system reliability. This paper presents operational history of the HVCM systems and examines failure mode statistical data since the modulators began operating at 60 Hz. System enhancements and upgrades aimed at providing long term reliable operation with minimal down time are also discussed in the paper.

Peplov, Vladimir V [ORNL; Anderson, David E [ORNL; Cutler, Roy I [ORNL; Hicks, Jim [ORNL; Saethre, Robert B [ORNL; Wezensky, Mark W [ORNL

2011-01-01T23:59:59.000Z

452

Lower Cost CPV 3-Sun Mirror Modules  

SciTech Connect

In a series of patent applications filed between 2002 and 2005, JX Crystals Inc described a evolutionary lower-cost low-concentration planar solar photovoltaic module that uses multiple linear rows of silicon cells and standard one-sun circuit laminations incorporating glass and EVA weather proofing encapsulations. The three novel features that we described are interdependent and integrated together to yield lower cost PV modules. These 3 novel features are: (1) The use of rows of linear mirrors or linear Fresnel lenses aligned with the cell rows and concentrating the sunlight onto the cell rows. (2) The addition of a thin aluminum sheet heat spreader on the back of the circuit lamination to spread the heat away from the cell rows so that the cell operating temperature remains acceptably low. (3) The incorporation of slots in the back of the aluminum sheet heat spreader to accommodate the differences in thermal expansion between the silicon cells, the glass, and the aluminum so that the circuit interconnectivity is maintained over time. Various embodiments of this planar linear concentrator panel are shown in figures 1 to 5. Figures 1 and 2 show the original planar linear concentrator module concept from July of 2002 with either mirrors (figure 1) or linear Fresnel lenses (figure 2). The idea was expanded in 2003 with the idea of an aluminum sheet heat spreader added to the back of a standard PV circuit lamination as shown in figure 3. In 2003, we also transitioned from half cells to third cells using SunPower cells as shown in figure 4. JX Crystals Inc then received funding for the 3-sun PV mirror module concept from the Shanghai Science and Technology Commission in 2003 and from the Shanghai Flower Port and the Shanghai Import and Export Trading Company in 2005. This funding led to a 800 panel pilot production run of our JX Crystals designed 3-sun module in 2006. 672 of these panels were installed in a 100 kW demonstration and an additional 24 panels were installed in a second 4 kW demonstration both at the Flower Port in Shanghai. Both of these systems were completed in 2006. Our 3-sun PV Panel concept has been described previously (see references 1, 2, & 3 available at www.jxcrystals.com under publication tab). We are now interested in bringing this potentially lower cost 3-sun technology back to the US. For any new technology, three issues need to be addressed. They are performance, durability, and cost. These topics are addressed in the next 3 sections.

Fraas, Dr. Lewis [JX Crystals, Inc.; Avery, James E. [JX Crystals, Inc.; Minkin, Leonid M [ORNL; Huang, H, [JX Crystals, Inc.; Gehl, Anthony C [ORNL; Maxey, L Curt [ORNL

2007-01-01T23:59:59.000Z

453

scriptEnv - loading modules before starting a script  

NLE Websites -- All DOE Office Websites (Extended Search)

scriptEnv - loading modules before starting a script scriptEnv - loading modules before starting a script scriptEnv - loading modules before starting a script In some cases a script needs to load modules before the script can be executed, but it can often be inconvenient or impossible to provide wrapper scripts which load the needed modules. CGI scripts on the gpweb resources or in the NERSC portal environment which require the genepool-specific python/perl/R or databases configuration modules are a strong example of this. NERSC provides the scriptEnv as a custom drop-in replacement for /usr/bin/env. scriptEnv loads your selected modules to allow your scripts to run easily and reproducibly. After constructing your scriptEnv, you only need replace the shebang line of your script to use your custom scriptEnv

454

Microsoft PowerPoint - FinalModule1.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1: Introduction to Earned Value 1: Introduction to Earned Value Management Prepared by: Module 1 - Introduction 1 Prepared by: Booz Allen Hamilton Module1: Introduction to Earned Value Welcome to Module 1. The objective of this module is to introduce you to Earned Value and lay the blueprint for the succeeding modules. This module will include the following topics: * Earned Value Management defined * The differences between Traditional Management and Earned Value Management * How Earned Value Management fits into a Program and Project environment * The framework necessary for proper Earned Value implementation Module 1 - Introduction 2 Prepared by: Booz Allen Hamilton What is Earned Value Management? Earned Value Management (EVM) is a systematic approach to the integration and measurement of cost, schedule, and technical (scope) accomplishments

455

T-674: Drupal Secure Password Hashes Module Security Bypass Vulnerability |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

74: Drupal Secure Password Hashes Module Security Bypass 74: Drupal Secure Password Hashes Module Security Bypass Vulnerability T-674: Drupal Secure Password Hashes Module Security Bypass Vulnerability July 22, 2011 - 3:00pm Addthis PROBLEM: Drupal Secure Password Hashes Module Security Bypass Vulnerability PLATFORM: Drupal Secure Password Hashes 6.X-1.0 Drupal Secure Password Hashes 5.X-1.4 ABSTRACT: The Secure Password Hashes module for Drupal is prone to a security-bypass vulnerability. reference LINKS: Drupal Homepage SA-CONTRIB-2011-026 - Secure Password Hashes (phpass) - Multiple Vulnerabilities IMPACT ASSESSMENT: Medium Discussion: This module uses the PHPass hashing library to try to store users hashed passwords securely. The module sets a fixed string for the 'pass' column in the {users} database column but does not replace the pass attribute of the account

456

Microsoft PowerPoint - FinalModule4.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4: Budgeting 4: Budgeting Prepared by: Prepared by: Booz Allen Hamilton Module 4 - Budgeting 1 Module 4: Budgeting Welcome to Module 4. The objective of this module is to introduce you to Budgeting Concepts and Definitions. The Topics that will be addressed in this Module include: * Cost/Schedule Baselines * WBS Levels: Control Accounts, Work Packages, Planning Packages * Elements of an Earned Value Contract Baseline * Proposed Cost and the Contract Budget Baseline * Control Account Manager Roles and Responsibilities * Review Prepared by: Booz Allen Hamilton Module 4 - Budgeting 2 The Budgeting Process In the previous module, we defined Planning as making decisions with the following objectives: * Define what will be performed (Statement of Work) * Determine how the work will be structured and tracked (Work Breakdown

457

In-Situ Measurement of Crystalline Silicon Modules Undergoing Potential-Induced Degradation in Damp Heat Stress Testing for Estimation of Low-Light Power Performance  

DOE Green Energy (OSTI)

The extent of potential-induced degradation of crystalline silicon modules in an environmental chamber is estimated using in-situ dark I-V measurements and applying superposition analysis. The dark I-V curves are shown to correctly give the module power performance at 200, 600 and 1,000 W/m2 irradiance conditions, as verified with a solar simulator. The onset of degradation measured in low light in relation to that under one sun irradiance can be clearly seen in the module design examined; the time to 5% relative degradation measured in low light (200 W/m2) was 28% less than that of full sun (1,000 W/m2 irradiance). The power of modules undergoing potential-induced degradation can therefore be characterized in the chamber, facilitating statistical analyses and lifetime forecasting.

Hacke, P.; Terwilliger, K.; Kurtz, S.

2013-08-01T23:59:59.000Z

458

How to Apply the ENERGY STAR Certified Building Decal  

NLE Websites -- All DOE Office Websites (Extended Search)

How to Apply the ENERGY STAR How to Apply the ENERGY STAR Certified Building Decal Page Cyan-and-White Decal Instructions Application Instructions 2 How to Make a Glass Plaque 4 Cyan-and-White Paper Templates 5 "Etched-Look" Decal Instructions Application Instructions 7 How to Make a Glass Plaque 9 "Etched-Look" Paper Templates 10 How to Apply the ENERGY STAR Cyan and White Certified Building Decal What's in this package: Two sets of: ENERGY STAR logo decal 1. "Certified Building" lettering decal, with thick white paper on 2. one side and thin, semi-translucent paper on the other side. Paper templates of logo and lettering What you'll need: Level 1. Masking tape 2. Rubbing alcohol and a clean, soft cloth 3. Drivers license, credit card, or other rigid

459

How to Apply for Weatherization Assistance | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How to Apply for Weatherization Assistance How to Apply for Weatherization Assistance How to Apply for Weatherization Assistance March 24, 2009 - 12:45pm Addthis Elizabeth Spencer Communicator, National Renewable Energy Laboratory A few weeks ago, the U.S. Department of Energy announced that it was investing $8 billion into weatherization and state energy grants-$5 billion of which is going directly to the Weatherization Assistance Program. And why is that interesting? Well, the Weatherization Assistance Program provides low-income families with free-of-charge, energy efficient upgrades to their homes. A more efficient home means that you pay less every month on your energy bills-and while that's the kind of upgrade anyone can benefit from, this program helps those who need those extra dollars the

460

Modular Applied General Equilibrium Tool (MAGNET) | Open Energy Information  

Open Energy Info (EERE)

Modular Applied General Equilibrium Tool (MAGNET) Modular Applied General Equilibrium Tool (MAGNET) Jump to: navigation, search Tool Summary Name: Modular Applied General Equilibrium Tool (MAGNET) Agency/Company /Organization: LEI Wageningen UR, the Netherlands Complexity/Ease of Use: Moderate Related Tools Ex Ante Appraisal Carbon-Balance Tool (EX-ACT) Climate Rapid Overview and Decision Support (C-ROADS) Simulator Partnership for Economic Policy Modeling and Policy Impact Analysis (MPIA) ... further results Find Another Tool FIND DEVELOPMENT IMPACTS ASSESSMENT TOOLS A modular global computable general equilibrium model that covers the whole economy and has been used extensively in agricultural, environmental, and trade policy analysis; builds on the GTAP model, and is the successor of LEITAP. Approach MAGNET is based on the Global Trade Analysis Project (GTAP) model and

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Overview Of Electromagnetic Methods Applied In Active Volcanic Areas Of  

Open Energy Info (EERE)

Of Electromagnetic Methods Applied In Active Volcanic Areas Of Of Electromagnetic Methods Applied In Active Volcanic Areas Of Western United States Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Overview Of Electromagnetic Methods Applied In Active Volcanic Areas Of Western United States Details Activities (7) Areas (2) Regions (0) Abstract: A better understanding of active volcanic areas in the United States through electromagnetic geophysical studies received foundation from the many surveys done for geothermal exploration in the 1970's. Investigations by governmental, industrial, and academic agencies include (but are not limited to) mapping of the Cascades. Long Valley/Mono area, the Jemez volcanic field, Yellowstone Park, and an area in Colorado. For one example - Mt. Konocti in the Mayacamas Mountains, California - gravity,

462

Geobotanical Remote Sensing Applied To Targeting New Geothermal Resource  

Open Energy Info (EERE)

Geobotanical Remote Sensing Applied To Targeting New Geothermal Resource Geobotanical Remote Sensing Applied To Targeting New Geothermal Resource Locations In The Us Basin And Range With A Focus On Dixie Meadows, Nv Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Geobotanical Remote Sensing Applied To Targeting New Geothermal Resource Locations In The Us Basin And Range With A Focus On Dixie Meadows, Nv Details Activities (1) Areas (1) Regions (0) Abstract: This paper presents an overview of the work our collaboration is doing to increase the detailed mapped resource base for geothermal exploration in the Western US. We are imaging several large areas in the western US with high resolution airborne hyperspectral and satellite multispectral sensors. We have now entered the phase where the remote sensing techniques and tools we are developing are mature enough to be

463

Guidance for Federal Departments and Agencies on Establishing, Applying,  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Guidance for Federal Departments and Agencies on Establishing, Guidance for Federal Departments and Agencies on Establishing, Applying, and Revising Categorical Exclusions Under the National Environmental Policy Act Guidance for Federal Departments and Agencies on Establishing, Applying, and Revising Categorical Exclusions Under the National Environmental Policy Act This guidance from the Council on Environmental Quality provides methods for substantiating categorical exclusions, clarifies the process for establishing categorical exclusions, outlines how agencies should engage the public when establishing and using categorical exclusions, describes how agencies can document the use of categorical exclusions, and recommends periodic agency review of existing categorical exclusions. Final Guidance for Federal Departments and Agencies on Establishing,

464

Guidance for Federal Departments and Agencies on Establishing, Applying,  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

for Federal Departments and Agencies on Establishing, for Federal Departments and Agencies on Establishing, Applying, and Revising Categorical Exclusions Under the National Environmental Policy Act Guidance for Federal Departments and Agencies on Establishing, Applying, and Revising Categorical Exclusions Under the National Environmental Policy Act This guidance from the Council on Environmental Quality provides methods for substantiating categorical exclusions, clarifies the process for establishing categorical exclusions, outlines how agencies should engage the public when establishing and using categorical exclusions, describes how agencies can document the use of categorical exclusions, and recommends periodic agency review of existing categorical exclusions. Final Guidance for Federal Departments and Agencies on Establishing,

465

Process for applying control variables having fractal structures  

DOE Patents (OSTI)

A process and apparatus for the application of a control variable having a fractal structure to a body or process. The process of the present invention comprises the steps of generating a control variable having a fractal structure and applying the control variable to a body or process reacting in accordance with the control variable. The process is applicable to electroforming where first, second and successive pulsed-currents are applied to cause the deposition of material onto a substrate, such that the first pulsed-current, the second pulsed-current, and successive pulsed currents form a fractal pulsed-current waveform.

Bullock, IV, Jonathan S. (Oak Ridge, TN); Lawson, Roger L. (Oliver Springs, TN)

1996-01-01T23:59:59.000Z

466

C: Applying the Toyota Production System to a Hospital Pharmacy  

E-Print Network (OSTI)

This paper presents the early results of an action research project to apply the principles of the Toyota Production System to a hospital pharmacy. We demonstrate that work systems can be improved through Bowen and Spears [3] Rules-in-Use: defining activities better, making simpler and more direct connections, and/or smoothing pathways. We also extend this work by introducing a problem-solving tool to facilitate process improvement. The paper will describe the interventions attempted, the results, and implications for applying the Rules-in-Use to health care environments.

Durward K. Sobek; Cindy Jimmerson

2003-01-01T23:59:59.000Z

467

Residential Sector Demand Module 1997, Model Documentation  

Reports and Publications (EIA)

This is the third edition of the Model Documentation Report: Residential Sector DemandModule of the National Energy Modeling System. It reflects changes made to the moduleover the past year for the Annual Energy Outlook 1997. Since last year, a subroutinewas added to the model which allows technology and fuel switching when space heaters,heat pump air conditioners, water heaters, stoves, and clothes dryers are retired in bothpre-1994 and post-1993 single-family homes. Also, a time-dependant function forcomputing the installed capital cost of equipment in new construction and the retail costof replacement equipment in existing housing was added.

John H. Cymbalsky

1997-01-01T23:59:59.000Z

468

Electricity market module: Electricity fuel dispatch submodule  

Science Conference Proceedings (OSTI)

In previous Annual Energy Outlooks (AEO), international electricity trade was represented in the National Energy Modeling System (NEMS) Electricity Market Module (EMM) modeling framework as an exogenous input. The exception to this exogenous treatment was for firm power projections, i.e., new Canadian hydroelectric model builds. The AEO95 implementation of EMM allowed Canadian hydroelectric projects to be selected in the Electricity Capacity Planning (ECP) submodule on an annual basis and otherwise addressed as any other purchased power commitments. This technical memorandum addresses modifications to the Electricity Fuel Dispatch Submodule implemented in AEO96 to enhance the treatment of international electricity trade through the representation of economy imports from Canada.

NONE

1996-06-01T23:59:59.000Z

469

Bio 3A -Applying to Health Professional Schools Dental Schools  

E-Print Network (OSTI)

Bio 3A - Applying to Health Professional Schools Dental Schools Admission Requirements and Helpful Requirements: Biology (w/lab) 1 to 1 1/2 years (At UCI Bio 93, 94, 97, 98, 99, *100 minimum). Many schools will require 3 labs. *BioSci 100 is a prerequisite for taking Bio labs at UCI. Some schools will require

Barrett, Jeffrey A.

470

Bio 3A -Applying to Health Professional Schools Pharmacy Schools  

E-Print Network (OSTI)

Bio 3A - Applying to Health Professional Schools Pharmacy Schools Admission Requirements individual web sites. Pharmacy School Admission Requirements: Biology (w/lab) Bio 93, 94*, 97, 98, 99, 100, E not be an interpersonal communication course) ­ not offered at UCI *Bio 94 is the prerequisite of Bio 97, but not required

Barrett, Jeffrey A.

471

A Test Calculus Framework applied to network security policies  

E-Print Network (OSTI)

A Test Calculus Framework applied to network security policies Yli`es Falcone1 , Jean'H`eres, France Abstract. We propose a syntax-driven test generation technique to au- tomaticaly derive abstract test cases from a set of requirements expressed in a linear temporal logic. Assuming that an elementary

Paris-Sud XI, Université de

472

Applying Bayesian Network Techniques to Prioritize Lean Six Sigma Efforts  

Science Conference Proceedings (OSTI)

In order to retain competitive advantages, many manufacturing organizations have applied Lean Six Sigma techniques to improve production processes. The general approach for implementing Lean Six Sigma is to perform various projects to tackle specific ... Keywords: Bayesian Network, Cause-and-Effect Relationships, Events of Interest, Lean, Probabilistic Inference, Six Sigma

Yanzhen Li, Rapinder S. Sawhne, Joseph H. Wilck

2013-04-01T23:59:59.000Z

473

Proceedings of the 2005 ACM symposium on Applied computing  

Science Conference Proceedings (OSTI)

Welcome to the 20th Annual ACM Symposium on Applied Computing (SAC 2005) hosted by the New Mexico Institute of Mining and Technology, Socorro, New Mexico, USA. As the Conference Chair and on behalf of the organizing committee, thank you for participating ...

Hisham M. Haddad; Andrea Omicini; Roger L. Wainwright; Lorie M. Liebrock

2005-03-01T23:59:59.000Z

474

Applying High Performance Computing to Analyzing by Probabilistic Model Checking  

E-Print Network (OSTI)

Applying High Performance Computing to Analyzing by Probabilistic Model Checking Mobile Cellular on the use of high performance computing in order to analyze with the proba- bilistic model checker PRISM. The Figure Generation Script 22 2 #12;1. Introduction We report in this paper on the use of high performance

Schneider, Carsten

475

Book review Carbon Nanotube Science: Synthesis, Properties and Appli-  

E-Print Network (OSTI)

Book review Carbon Nanotube Science: Synthesis, Properties and Appli- cations, Peter J.F. Harris in the nanotube discovery is dis- cussed in the first chapter of this book), a few years after ful- lerenes were of the nanotechnology era ­ you'll find their pictures on book covers, in newspaper articles and magazine centerfolds

Harris, Peter J F

476

Applying General Access Structure to Metering Ventzislav Nikov  

E-Print Network (OSTI)

Applying General Access Structure to Metering Schemes Ventzislav Nikov Department of Mathematics.vandewalle@esat.kuleuven.ac.be Abstract In order to decide on advertisement fees for web servers, Naor and Pinkas introduced metering number of clients. Several researchers have generalized the idea of Naor and Pinkas: #12;rst metering

International Association for Cryptologic Research (IACR)

477

Applying General Access Structure to Metering Ventzislav Nikov  

E-Print Network (OSTI)

Applying General Access Structure to Metering Schemes Ventzislav Nikov Department of Mathematics.vandewalle@esat.kuleuven.ac.be Abstract In order to decide on advertisement fees for web servers, Naor and Pinkas introduced metering number of clients. Several researchers have generalized the idea of Naor and Pinkas: first metering

International Association for Cryptologic Research (IACR)

478

Modeling and simulation applied in modernization of energy production plants  

Science Conference Proceedings (OSTI)

The present work presents a methodology that has been developed and successfully applied to support the information requirements of engineers in charge of the operation, modernization, and/or maintenance of energy production plants (power, oil and gas). ... Keywords: CAD software, energy production, engineering design and data management, industrial plant, operation and maintenance support

Jess Vzquez Bustos; Benjamn Eddie Zayas Prez

2011-06-01T23:59:59.000Z

479

A companion modelling approach applied to forest management planning  

Science Conference Proceedings (OSTI)

To assist the Societe Civile des Terres du Larzac (SCTL) in its effort to develop alternative forest management plans, a group of researchers and extension officers proposed applying a companion modelling approach. The objective was to support forest ... Keywords: Companion modelling, Forest management, Livestock farming, Multi-agent system, Participatory modelling

C. Simon; M. Etienne

2010-11-01T23:59:59.000Z

480

Neutron activation analysis applied to energy and environment  

SciTech Connect

Neutron activation analysis was applied to a number of problems concerned with energy production and the environment. Burning of fossil fuel, the search for new sources of uranium, possible presence of toxic elements in food and water, and the relationship of trace elements to cardiovascular disease are some of the problems in which neutron activation was used. (auth)

Lyon, W.S.

1975-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "module cxs applied" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Cryogenic Silicon Microstrip Detector Modules for LHC  

E-Print Network (OSTI)

CERN is presently constructing the LHC, which will produce collisions of 7 TeV protons in 4 interaction points at a design luminosity of 1034 cm-2 s-1. The radiation dose resulting from the operation at high luminosity will cause a serious deterioration of the silicon tracker performance. The state-of-art silicon microstrip detectors can tolerate a fluence of about 3 1014 cm-2 of hadrons or charged leptons. This is insufficient, however, for long-term operation in the central parts of the LHC trackers, in particular after the possible luminosity upgrade of the LHC. By operating the detectors at cryogenic temperatures the radiation hardness can be improved by a factor 10. This work proposes a cryogenic microstrip detector module concept which has the features required for the microstrip trackers of the upgraded LHC experiments at CERN. The module can hold an edgeless sensor, being a good candidate for improved luminosity and total cross-section measurements in the ATLAS, CMS and TOTEM experiments. The design o...

Perea-Solano, B

2004-01-01T23:59:59.000Z

482

Flat-Plate Photovoltaic Module Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Module Basics Module Basics Flat-Plate Photovoltaic Module Basics August 20, 2013 - 4:25pm Addthis Flat-plate photovoltaic (PV) modules are made of several components, including the front surface materials, encapsulant, rear surface, and frame. Front Surface Materials The front surface of a flat-plate PV module must have a high transmission in the wavelengths that can be used by the solar cells in the module. For example, for silicon solar cells, the top surface must have high transmission of light with wavelengths from 350 to 1200 nm. Also, reflection from the front surface should be minimal. An antireflection coating added to the top surface can greatly reduce the reflection of sunlight, and texturing of the surface can cause light that strikes the surface to stay within the cells. Unfortunately, these textured

483

Integrated Modules for Bioassay (IMBA) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Integrated Modules for Bioassay (IMBA) Integrated Modules for Bioassay (IMBA) Integrated Modules for Bioassay (IMBA) Current Central Registry Toolbox Version(s): IMBA ExpertTM USDOE Edition version 4.0.28 Code Owner: UK Health Protection Agency (HPA) Description: IMBA ExpertTM (IX) software suite comprises a series of independent modules (referred to as sub-modules) that implement the International Commission on Radiological Protection (ICRP) Publication 66, Human Respiratory Tract Model (HRTM) and the ICRP Publications 30 (series), 67, 68, 69, and 71 biokinetic models. In 2001, the United Kingdom (UK) National Radiological Protection Board (NRPB), whose functions were absorbed later into the UK Health Protection Agency (HPA), and ACJ & Associates Inc., began development of an interface (referred to as a shell) for the IMBA modules. This effort was funded in

484

Residential photovoltaic module and array requirements study. Final report  

SciTech Connect

Burt Hill Kosar Rittelmann Associates has conducted a study to identify design requirements for photovoltaic modules and arrays used in residential applications. Building codes and referenced standards were reviewed for their applicability to residential photovoltaic array installations. Four installation types were identified - integral (replaces roofing), direct (mounted on top of roofing), stand-off (mounted away from roofing), and rack (for flat or low slope roofs, or ground mounted). Installation costs were developed for these mounting types as a function of panel/module size. cost drivers were identified. Studies were performed to identify optimum module shapes and sizes and operating voltage cost drivers. The general conclusion is that there are no perceived major obstacles to the use of photovoltaic modules in residential arrays. However, there is no applicable building code category for residential photovolttaic modules and arrays and early additional work is needed with standards writing organizations to develop residential module and array requirements.

1979-06-01T23:59:59.000Z

485

A solar module fabrication process for HALE solar electric UAVs  

DOE Green Energy (OSTI)

We describe a fabrication process used to manufacture high power-to-weight-ratio flexible solar array modules for use on high-altitude-long-endurance (HALE) solar-electric unmanned air vehicles (UAVs). These modules have achieved power-to-weight ratios of 315 and 396 W/kg for 150{mu}m-thick monofacial and 110{mu}m-thick bifacial silicon solar cells, respectively. These calculations reflect average module efficiencies of 15.3% (150{mu}m) and 14.7% (110{mu}m) obtained from electrical tests performed by Spectrolab, Inc. under AMO global conditions at 25{degrees}C, and include weight contributions from all module components (solar cells, lamination material, bypass diodes, interconnect wires, and adhesive tape used to attach the modules to the wing). The fabrication, testing, and performance of 32 m{sup 2} of these modules will be described.

Carey, P.G.; Aceves, R.C.; Colella, N.J.; Williams, K.A. [Lawrence Livermore National Lab., CA (United States); Sinton, R.A. [Private Consultant, San Jose, CA (United States); Glenn, G.S. [Spectrolab, Inc., Sylmar, CA (United States)

1994-12-12T23:59:59.000Z

486

Microsoft PowerPoint - FinalModule2.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2: Work Breakdown Structure 2: Work Breakdown Structure Prepared by: Module 2 - Work Breakdown Structure 1 Prepared by: Booz Allen Hamilton Module 2: Work Breakdown Structure Welcome to Module 2. The objective of this module is to introduce you to Work Breakdown Structure (WBS) and other supporting documents. This module will include defining and illustrating the following topics: * Work Breakdown Structure * WBS dictionary * Organizational Breakdown Structure (OBS) * Responsibility Assignment Matrix (RAM) Module 2 - Work Breakdown Structure 2 Prepared by: Booz Allen Hamilton What is a Work Breakdown Structure? Planning a project using earned value management is no different than the initial planning necessary to implement any given project. There are basic items that you need to know and understand as a project manager:

487

BEP project for Applied Mathematics/Applied Physics double degree Numerical solution of a three-dimensional electromagnetic  

E-Print Network (OSTI)

-dimensional electromagnetic force field Imagine a quadratic piece of metal, which is subject to a static current flux at its top boundary and insulated at the bottom. Assuming the current flux to be of Gaussian shape and applying suitable boundary conditions, we can derive equations to describe the current flux in the metal

Vuik, Kees

488

A Quick Guide for Applying at Mason Applying online is as easy as 1-2-3!  

E-Print Network (OSTI)

Jobs" from the quick links.. You can search jobs in the following ways: · Keywords - enter your own search terms · Posted Within - a drop-down list will appear ­ select from day, week, or month Innovation Is Tradition Page 1 of 6 11/15/2012 #12;A Quick Guide for Applying at Mason Step 1: Search

489

Final Design of the SLAC P2 Marx Klystron Modulator  

Science Conference Proceedings (OSTI)

The SLAC P2 Marx has been under development for two years, and follows on the P1 Marx as an alternative to the baseline klystron modulator for the International Linear Collider. The P2 Marx utilizes a redundant architecture, air-insulation, a control system with abundant diagnostic access, and a novel nested droop correction scheme. This paper is an overview of the design of this modulator. There are several points of emphasis for the P2 Marx design. First, the modulator must be compatible with the ILC two-tunnel design. In this scheme, the modulator and klystron are located within a service tunnel with limited access and available footprint for a modulator. Access to the modulator is only practical from one side. Second, the modulator must have high availability. Robust components are not sufficient alone to achieve availability much higher than 99%. Therefore, redundant architectures are necessary. Third, the modulator must be relatively low cost. Because of the large number of stations in the ILC, the investment needed for the modulator components is significant. High-volume construction techniques which take advantage of an economy of scale must be utilized. Fourth, the modulator must be simple and efficient to maintain. If a modulator does become inoperable, the MTTR must be small. Fifth, even though the present application for the modulator is for the ILC, future accelerators can also take advantage of this development effort. The hardware, software, and concepts developed in this project should be designed such that further development time necessary for other applications is minimal.

Kemp, M.A.; Benwell, A.; Burkhart, C.; Larsen, R.; MacNair, D.; Nguyen, M.; Olsen, J.; /SLAC

2011-11-08T23:59:59.000Z

490

Assembly of opto-electronic module with improved heat sink  

DOE Patents (OSTI)

A heat sink for a transceiver optoelectronic module including dual direct heat paths and a structure which encloses a number of chips having a central web which electrically isolates transmitter and receiver chips from each other. A retainer for an optical coupler having a port into which epoxy is poured. An overmolded base for an optoelectronic module having epoxy flow controller members built thereon. Assembly methods for an optoelectronic module including gap setting and variation of a TAB bonding process.

Chan, Benson (Vestal, NY); Fortier, Paul Francis (Richelieu, CA); Freitag, Ladd William (Rochester, MN); Galli, Gary T. (Binghampton, NY); Guindon, Francois (Stukely-sud, CA); Johnson, Glen Walden (Yorktown Heights, NY); Letourneau, Martial (Granby, CA); Sherman, John H. (Lisle, NY); Tetreault, Real (Granby, CA)

2004-11-23T23:59:59.000Z

491

Engineering Technical Training Modules - Throttle Valves 1.0  

Science Conference Proceedings (OSTI)

The purpose of this training module is to provide an understanding of specifying throttle valves in a nuclear power plant. The module provides the student with an understanding of the different types of throttle valves, how to select a throttle valve, understand the flow characteristics of different throttle valves, and understanding negative characteristics that can occur when the wrong valve is chosen for different applications. Prior to using this module, the student should understand the fundamental...

2011-06-29T23:59:59.000Z

492

Engineering Technical Training Modules - Flow Measurement Version 1.0  

Science Conference Proceedings (OSTI)

The purpose of this training module is to provide an understanding of calculating flow and the various types of flow measurement devices. The module also provides information related to device selection, installation, failure modes, calibration, and instrument error. This computer-based training (CBT) module is intended for use by new engineers as well as engineers changing jobs where basic knowledge of this subject is a new requirement. This training is intended to help individuals acquire basic knowled...

2011-10-21T23:59:59.000Z

493

High Power Modulator/regulators for neutral beam sources  

SciTech Connect

PPPL has recently completed two new Modulator/Regulators for neutral injection sources used on the ATC machine and is constructing four new ones for use with sources on the PLT machine. The ATC modulator uses the well proven 4CX35,000C tetrode as the main switch tube, while the PLT modulators will be using the new but significantly higher powered X-2170 tetrodes. Some interesting circuit and manufacturing techniques are discussed. (MOW)

Lawson, J.Q.; Deitz, A.

1975-01-01T23:59:59.000Z

494

International Institute for Applied Systems Analysis | Open Energy  

Open Energy Info (EERE)

Analysis Analysis Jump to: navigation, search Logo: International Institute for Applied Systems Analysis Name International Institute for Applied Systems Analysis Address Schlossplatz 1, A-2361 Place Laxenburg, Austria Number of employees 201-500 Year founded 1972 Phone number (+43 2236) 807 0 Coordinates 48.0682549°, 16.358201° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":48.0682549,"lon":16.358201,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

495

Argonne applied mathematicians use INCITE awards to attack energy problems  

NLE Websites -- All DOE Office Websites (Extended Search)

Argonne applied mathematicians use INCITE awards to attack energy problems Argonne applied mathematicians use INCITE awards to attack energy problems March 27, 2013 Tweet EmailPrint What is the best possible power grid configuration for our nation? How can we balance the increasing demands for power while minimizing costs and avoiding waste of resources? Last year, Mihai Anitescu, a computational mathematician in Argonne's Mathematics and Computer Science Division. received DOE funding to establish the Multifaceted Mathematics for Complex Energy Systems (M2ACS) to tackle these questions. As part of the M2ACS research, Anitescu and his colleagues at Argonne are focusing on ways to optimize the effects of randomly changing variables, say, in wind or resource demand. Such variables can number into the billions. And to be useful for energy systems planning, any calculations

496

Generative Design Systems Applied to Low-Energy Buildings  

NLE Websites -- All DOE Office Websites (Extended Search)

Generative Design Systems Applied to Low-Energy Buildings Generative Design Systems Applied to Low-Energy Buildings Speaker(s): Maria Luisa de Oliveira Gama Caldas Date: March 15, 2012 - 12:00pm Location: 90-3122 Seminar Host/Point of Contact: Paul Mathew Generative Design Systems (GDS) represent a step beyond parametric models, integrating design goals, building simulations and shape generation. In this seminar, present and future research projects on the application of different GDS to low-energy buildings are discussed. The software GENE_ARCH integrates energy simulations with multicriteria search methods such as pareto genetic algorithms, to locate acceptable alternatives that move the current design towards performance goals set by the user. DIVA, a system that integrates parametric geometrical modeling with Radiance, Daysim and

497

Environmental Impact and Sustainability Applied General Equilibrium Model  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » Environmental Impact and Sustainability Applied General Equilibrium Model (ENVISAGE) Jump to: navigation, search LEDSGP green logo.png FIND MORE DIA TOOLS This tool is part of the Development Impacts Assessment (DIA) Toolkit from the LEDS Global Partnership. Tool Summary LAUNCH TOOL Name: Environmental Impact and Sustainability Applied General Equilibrium Model (ENVISAGE) Agency/Company /Organization: World Bank Sector: Climate Topics: Analysis Tools Complexity/Ease of Use: Advanced Website: go.worldbank.org/ZC77UJYJ50 Related Tools TransportToolkit Prototype Threshold 21 Model General Equilibrium Modeling Package (GEMPACK) ... further results Designed to analyze a variety of issues related to the economics of climate

498

Applied Super Conductor Group, Oxide Molecular Beam Epitaxy Group,  

NLE Websites -- All DOE Office Websites (Extended Search)

AEMG Homepage AEMG Homepage Site Details Homepage Research Publications Presentations Facilities How to Contact Us Other Information Basic Energy Sciences Directorate Links BNL Site Index Can't View PDFs? Advanced Energy Materials Group Applied Superconductivity The applied superconductivity research (past funded by DOE Office of Electricity Delivery and Energy Reliability) is related to modernization of the U.S. power grid. One direction of the modernization is replacement of normal metal (copper, aluminum) transmission lines with High Temperature Superconducting (HTS) cables. Our group concentrates its effort on studying fundamental thermodynamics of nucleation and texture development of thick YBCO layers. High-performance YBCO layer is a critical element of modern second generation (2G) HTS wire.

499

Fifth SIAM conference on applied linear algebra. Final report  

SciTech Connect

The SIAM Conferences on Applied Linear Algebra are the centerpiece of activities for the SIAG on Linear Algebra. They are held every three years and bring together a diverse group of applied linear algebraists, representing industry, government and academics in both matrix theory and matrix computations. This sequence of conferences has two related goals: (1) to be useful and interesting to linear algebraists of every area of specialization, and, (2) to develop and expose connections among problems in different areas. Many aspects of the 1994 conference were carefully chosen to enhance interchange between the various groups and yet still provide a solid focus on specialities. The organizing committee adopted a new meeting structure to resolve the conflict between these two goals at earlier meetings in the series. We have prepared this report for others who may wish to consider our structure as an alternative to more traditional arrangements.

Lewis, J.G.; Gilbert, J.R.; Parlett, B.N.

1994-11-16T23:59:59.000Z

500

Applied Science Division annual report, Environmental Research Program FY 1983  

Science Conference Proceedings (OSTI)

The primary concern of the Environmental Research Program is the understanding of pollutant formation, transport, and transformation and the impacts of pollutants on the environment. These impacts include global, regional, and local effects on the atmosphere and hydrosphere, and on certain aspects of human health. This multidisciplinary research program includes fundamental and applied research in physics, chemistry, engineering, and biology, as well as research on the development of advanced methods of measurement and analysis. During FY 1983, research concentrated on atmospheric physics and chemistry, applied physics and laser spectroscopy, combustion theory and phenomena, environmental effects of oil shale processing, freshwater ecology and acid precipitation, trace element analysis for the investigation of present and historical environmental impacts, and a continuing survey of instrumentation for environmental monitoring.

Cairns, E.J.; Novakov, T.

1984-05-01T23:59:59.000Z