National Library of Energy BETA

Sample records for mit joint program

  1. Jointly Sponsored Research Program

    SciTech Connect (OSTI)

    Everett A. Sondreal; John G. Hendrikson; Thomas A. Erickson

    2009-03-31

    U.S. Department of Energy (DOE) Cooperative Agreement DE-FC26-98FT40321 funded through the Office of Fossil Energy and administered at the National Energy Technology Laboratory (NETL) supported the performance of a Jointly Sponsored Research Program (JSRP) at the Energy & Environmental Research Center (EERC) with a minimum 50% nonfederal cost share to assist industry in commercializing and effectively applying highly efficient, nonpolluting energy systems that meet the nation's requirements for clean fuels, chemicals, and electricity in the 21st century. The EERC in partnership with its nonfederal partners jointly performed 131 JSRP projects for which the total DOE cost share was $22,716,634 (38%) and the nonfederal share was $36,776,573 (62%). Summaries of these projects are presented in this report for six program areas: (1) resource characterization and waste management, (2) air quality assessment and control, (3) advanced power systems, (4) advanced fuel forms, (5) value-added coproducts, and (6) advanced materials. The work performed under this agreement addressed DOE goals for reductions in CO{sub 2} emissions through efficiency, capture, and sequestration; near-zero emissions from highly efficient coal-fired power plants; environmental control capabilities for SO{sub 2}, NO{sub x}, fine respirable particulate (PM{sub 2.5}), and mercury; alternative transportation fuels including liquid synfuels and hydrogen; and synergistic integration of fossil and renewable resources.

  2. 2013 Progress Report -- DOE Joint Genome Institute (Program Document...

    Office of Scientific and Technical Information (OSTI)

    Program Document: 2013 Progress Report -- DOE Joint Genome Institute Citation Details In-Document Search Title: 2013 Progress Report -- DOE Joint Genome Institute In October 2012, ...

  3. Jointly Sponsored Research Program Energy Related Research

    SciTech Connect (OSTI)

    Western Research Institute

    2009-03-31

    Cooperative Agreement, DE-FC26-98FT40323, Jointly Sponsored Research (JSR) Program at Western Research Institute (WRI) began in 1998. Over the course of the Program, a total of seventy-seven tasks were proposed utilizing a total of $23,202,579 in USDOE funds. Against this funding, cosponsors committed $26,557,649 in private funds to produce a program valued at $49,760,228. The goal of the Jointly Sponsored Research Program was to develop or assist in the development of innovative technology solutions that will: (1) Increase the production of United States energy resources - coal, natural gas, oil, and renewable energy resources; (2) Enhance the competitiveness of United States energy technologies in international markets and assist in technology transfer; (3) Reduce the nation's dependence on foreign energy supplies and strengthen both the United States and regional economies; and (4) Minimize environmental impacts of energy production and utilization. Under the JSR Program, energy-related tasks emphasized enhanced oil recovery, heavy oil upgrading and characterization, coal beneficiation and upgrading, coal combustion systems development including oxy-combustion, emissions monitoring and abatement, coal gasification technologies including gas clean-up and conditioning, hydrogen and liquid fuels production, coal-bed methane recovery, and the development of technologies for the utilization of renewable energy resources. Environmental-related activities emphasized cleaning contaminated soils and waters, processing of oily wastes, mitigating acid mine drainage, and demonstrating uses for solid waste from clean coal technologies, and other advanced coal-based systems. Technology enhancement activities included resource characterization studies, development of improved methods, monitors and sensors. In general the goals of the tasks proposed were to enhance competitiveness of U.S. technology, increase production of domestic resources, and reduce environmental impacts associated with energy production and utilization. This report summarizes the accomplishments of the JSR Program.

  4. Russian Health Studies Program - Joint Coordinating Committee for Radiation

    Energy Savers [EERE]

    Effects Research (JCCRER) | Department of Energy Joint Coordinating Committee for Radiation Effects Research (JCCRER) Russian Health Studies Program - Joint Coordinating Committee for Radiation Effects Research (JCCRER) Joint Coordinating Committee for Radiation Effects Research (JCCRER) All About the Joint Coordinating Committee for Radiation Effects Research What is the JCCRER? Why is it important? DOE's Russian Health Studies Program Principal Areas of Cooperation Under the JCCRER

  5. DOE-EERC jointly sponsored research program

    SciTech Connect (OSTI)

    Hendrikson, J.G.; Sondreal, E.A.

    1999-09-01

    U.S. Department of Energy (DOE) Cooperative Agreement DE-FC21-93MC30098 funded through the Office of Fossil Energy and administered at the Federal Energy Technology Center (FETC) supported the performance of a Jointly Sponsored Research Program (JSRP) at the Energy and Environmental Research Center (EERC) with a minimum 50% nonfederal cost share to assist industry in commercializing and effectively applying efficient, nonpolluting energy technologies that can compete effectively in meeting market demands for clean fuels, chemical feedstocks, and electricity in the 21st century. The objective of the JSRP was to advance the deployment of advanced technologies for improving energy efficiency and environmental performance through jointly sponsored research on topics that would not be adequately addressed by the private sector alone. Examples of such topics include the barriers to hot-gas cleaning impeding the deployment of high-efficiency power systems and the search for practical means for sequestering CO{sub 2} generated by fossil fuel combustion. The selection of particular research projects was guided by a combination of DOE priorities and market needs, as provided by the requirement for joint venture funding approved both by DOE and the private sector sponsor. The research addressed many different energy resource and related environmental problems, with emphasis directed toward the EERC's historic lead mission in low-rank coals (LRCs), which represent approximately half of the U.S. coal resources in the conterminous states, much larger potential resources in Alaska, and a major part of the energy base in the former U.S.S.R., East Central Europe, and the Pacific Rim. The Base and JSRP agreements were tailored to the growing awareness of critical environmental issues, including water supply and quality, air toxics (e.g., mercury), fine respirable particulate matter (PM{sub 2.5}), and the goal of zero net CO{sub 2} emissions.

  6. The Utility-Scale Joint-Venture Program

    SciTech Connect (OSTI)

    Gallup, D.R.; Mancini, T.R.

    1994-06-01

    The Department of Energy`s Utility-Scale Joint-Venture (USJV) Program was developed to help industry commercialize dish/engine electric systems. Sandia National Laboratories developed this program and has placed two contracts, one with Science Applications International Corporation`s Energy Projects Division and one with the Cummins Power Generation Company. In this paper we present the designs for the two dish/Stirling systems that are being developed through the USJV Program.

  7. Massachusetts Beryllium Screening Program for Former Workers of Wyman-Gordon, Norton Abrasives, and MIT/Nuclear Metals

    SciTech Connect (OSTI)

    Pepper, L.D.

    2008-05-21

    The overall objective of this project was to provide medical screening to former workers of Wyman-Gordon Company, Norton Abrasives, and MIT/Nuclear Metals (NMI) in order to prevent and minimize the health impact of diseases caused by site related workplace exposures to beryllium. The program was developed in response to a request by the U.S. Department of Energy (DOE) that had been authorized by Congress in Section 3162 of the 1993 Defense Authorization Act, urging the DOE to ??carry out a program for the identification and ongoing evaluation of current and former DOE employees who are subjected to significant health risks during such employment." This program, funded by the DOE, was an amendment to the medical surveillance program for former DOE workers at the Nevada Test Site (NTS). This program??s scope included workers who had worked for organizations that provided beryllium products or materials to the DOE as part of their nuclear weapons program. These organizations have been identified as Beryllium Vendors.

  8. LWRS Program and EPRI Long-Term Operations Program - Joint R&D Plan |

    Energy Savers [EERE]

    Department of Energy LWRS Program and EPRI Long-Term Operations Program - Joint R&D Plan LWRS Program and EPRI Long-Term Operations Program - Joint R&D Plan To address the challenges associated with pursuing commercial nuclear power plant operations beyond 60 years, the U.S. Department of Energy's (DOE) Office of Nuclear Energy (NE) and the Electric Power Research Institute (EPRI) have established separate but complementary research and development programs: DOE-NE's Light Water

  9. LWRS Program and EPRI Long-Term Operations Program - Joint R&D Plan |

    Office of Environmental Management (EM)

    Department of Energy LWRS Program and EPRI Long-Term Operations Program - Joint R&D Plan LWRS Program and EPRI Long-Term Operations Program - Joint R&D Plan To address the challenges associated with pursuing commercial nuclear power plant operations beyond 60 years, the U.S. Department of Energy's (DOE) Office of Nuclear Energy (NE) and the Electric Power Research Institute (EPRI) have established separate but complementary research and development programs: DOE-NE's Light Water

  10. DOE-NE Light Water Reactor Sustainability Program and EPRI Long Term Operations Program Joint Research and Development

    Broader source: Energy.gov [DOE]

    Description of Joint DOE and EPRI research and development programs related to reactor sustainability INL/EXT-12-24562

  11. Technical status of the Dish/Stirling Joint Venture Program

    SciTech Connect (OSTI)

    Bean, J.R.; Diver, R.B.

    1995-06-01

    Initiated in 1991; the Dish/Stirling Joint Venture Program (DSJVP) is a 5-year, $17.2 million joint venture which is funded by Cummins Power Generation, Inc. (CPG) of Columbus, Indiana and the United States Department of Energy`s (DOE) Solar Thermal and Biomass Power Division. Sandia National Laboratories administers and provides technical management for this contract on the DOE`s behalf. In January, 1995; CPG advanced to Phase 3 of this three-phase contract. The objective of the DSJVP is to develop and commercialize a 7-kW. Dish/Stirling System for remote power markets by 1997. In this paper, the technical status of the major subsystems which comprise the CPG 7-kW{sub e} Dish/Stirling System is presented. These subsystems include the solar concentrator, heat pipe receiver, engine/alternator, power conditioning, and automatic controls.

  12. DOE, USDA, and NSF Launch Joint Climate Change Prediction Research Program

    Energy Savers [EERE]

    | Department of Energy DOE, USDA, and NSF Launch Joint Climate Change Prediction Research Program DOE, USDA, and NSF Launch Joint Climate Change Prediction Research Program March 22, 2010 - 12:00am Addthis Washington, DC - The U.S. Departments of Energy and Agriculture and the National Science Foundation (NSF) announced the launch of a joint research program to produce high-resolution models for predicting climate change and its resulting impacts. Called Decadal and Regional Climate

  13. DOD Instruction 3030.3 - Joint Land Use Study Program | Open...

    Open Energy Info (EERE)

    ProgramPermittingRegulatory GuidanceInstructions Abstract This instruction implements policies, assigns responsibilities, and prescribes procedures for executing the Joint Land...

  14. Michael Demkowicz: MIT

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Michael Demkowicz: MIT Alumni Link: Opportunities, News and Resources for Former Employees Latest Issue:September 2015 all issues All Issues » submit Michael Demkowicz: MIT Former postdoc now an Associate Professor at MIT September 3, 2014 Michael Demkowicz Michael Demkowicz Contact Linda Anderman Email Michael Demkowicz Demkowicz now at MIT Michael Demkowicz worked at the Lab from 2005 to 2008 with the Materials Science and Technology division, first as a postdoc and then as a technical staff

  15. Joint Outreach Task Group Former Workers Screening Program

    Broader source: Energy.gov [DOE]

    The Joint Outreach Task Group (JOTG) includes representatives from DOE, Department of Labor (DOL), the National Institute for Occupational Safety and Health (NIOSH), the Offices of the Ombudsman for DOL and NIOSH, and the DOE-funded FWP projects.

  16. Jointly Sponsored Research Program on Energy Related Research

    SciTech Connect (OSTI)

    No, author

    2013-12-31

    Cooperative Agreements, DE-FC26-08NT43293, DOE-WRI Cooperative Research and Development Program for Fossil Energy-Related Resources began in June 2009. The goal of the Program was to develop, commercialize, and deploy technologies of value to the nation’s fossil and renewable energy industries. To ensure relevancy and early commercialization, the involvement of an industrial partner was encouraged. In that regard, the Program stipulated that a minimum of 20% cost share be achieved in a fiscal year. This allowed WRI to carry a diverse portfolio of technologies and projects at various development technology readiness levels. Depending upon the maturity of the research concept and technology, cost share for a given task ranged from none to as high as 67% (two-thirds). Over the course of the Program, a total of twenty six tasks were proposed for DOE approval. Over the period of performance of the Cooperative agreement, WRI has put in place projects utilizing a total of $7,089,581 in USDOE funds. Against this funding, cosponsors have committed $7,398,476 in private funds to produce a program valued at $14,488,057. Tables 1 and 2 presented at the end of this section is a compilation of the funding for all the tasks conducted under the program. The goal of the Cooperative Research and Development Program for Fossil Energy-Related Resources was to through collaborative research with the industry, develop or assist in the development of innovative technology solutions that will: • Increase the production of United States energy resources – coal, natural gas, oil, and renewable energy resources; • Enhance the competitiveness of United States energy technologies in international markets and assist in technology transfer; • Reduce the nation's dependence on foreign energy supplies and strengthen both the United States and regional economies; and • Minimize environmental impacts of energy production and utilization. Success of the Program can be measured by several criteria. Using the deployment of the federal funding with industrial participation as a performance criterion, over the course of the program, the copsonsors contributed more dollars than the federal funds. As stated earlier, a little more than half of the funding for the Program was derived from industrial partners. The industrial partners also enthusiastically supported the research and development activities with cash contribution of $4,710,372.67, nearly 65% of the required cost share. Work on all of the tasks proposed under the Cooperative Agreement has been completed. This report summarizes and highlights the results from the Program. Under the Cooperative Agreement Program, energy-related tasks emphasized petroleum processing, upgrading and characterization, coal and biomass beneficiation and upgrading, coal combustion systems development including oxy-combustion, emissions monitoring and abatement, coal gasification technologies including gas clean-up and conditioning, hydrogen and liquid fuels production, and the development of technologies for the utilization of renewable energy resources. Environmental-related activities emphasized cleaning contaminated soils using microbial fuel cells, development of processes and sorbents for emissions reduction and recovery of water from power plant flue gas, and biological carbon capture and reuse. Technology enhancement activities included resource characterization studies, development of improved methods, monitors and sensors. In general the goals of the tasks proposed were to enhance competitiveness of U.S. technology, increase production of domestic resources, and reduce environmental impacts associated with energy production and utilization. Technologies being brought to commercialization as a result of the funds provided by the Cooperative Agreement contribute to the overall goals of the USDOE and the nation. Each has broad applicability both within the United States and abroad, thereby helping to enhance the competitiveness of U.S. energy technologies in international markets and assisting in technology transfer. Under the Cooperative Agreement Program, WRI has furthered the development of two different coal upgrading technologies. River Basin Energy technology was scaled-up and demonstrated at a nominal 40 tpd size. Similarly, WRI’s patented mercury removal technology further developed into WRITE Coal technology which was then integrated into oxy-combustion and gasification systems for IGCC and fuels production. Integrated systems with WRITE Coal technology applied at the front end represent substantial environmental and efficiency gains. A variation of the RBE coal upgrading technology is being commercialized as a torrefaction technology for woody biomass. WRI worked with EPRI and NIST to develop and improve mercury calibration standards for emissions monitoring. Working with Chart Energy and Chemicals, WRI scaled-up compact reactor technology for the synthesis of fuels and chemicals from syngas. Compact reactor technology represents a five-fold increase in productivity over conventional reactors making smaller-scale distributed synthesis plants an economical viability. Similarly, WRI's patented mixed alcohol synthesis catalyst production is being scaled-up in collaboration with a commercial catalyst manufacturer.

  17. Thomas Moore creates joint invention with MIT

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    split water into hydrogen and oxygen - a potential pathway to sustainable energy production. ... led Moore to suggest that a type of solar cell he was developing could serve as a ...

  18. DOE-NE Light Water Reactor Sustainability Program and EPRI Long Term Operation Program … Joint Research & Development Plan

    Office of Environmental Management (EM)

    2-24562 Revision 4 DOE-NE Light Water Reactor Sustainability Program and EPRI Long Term Operations Program - Joint Research and Development Plan April 2015 U.S. Department of Energy Office of Nuclear Energy DISCLAIMER This information was prepared as an account of work sponsored by an agency of the U.S. Government. Neither the U.S. Government nor any agency thereof, nor any of their employees, makes any warranty, expressed or implied, or assumes any legal liability or responsibility for the

  19. Final Technical Report for the MIT Annular Fuel Research Project

    SciTech Connect (OSTI)

    Mujid S. Kazimi; Pavel Hejzlar

    2008-01-31

    MIT-NFC-PR-082 (January 2006) Abstract This summary provides an overview of the results of the U.S. DOE funded NERI (Nuclear Research ENergy Initiative) program on development of the internally and externally cooled annular fuel for high power density PWRs. This new fuel was proposed by MIT to allow a substantial increase in poer density (on the order of 30% or higher) while maintaining or improving safety margins. A comprehensive study was performed by a team consisting of MIT (lead organization), Westinghuse Electric Corporation, Gamma Engineering Corporation, Framatome ANP(formerly Duke Engineering) and Atomic Energy of Canada Limited.

  20. MIT- Earth Resources Laboratory | Open Energy Information

    Open Energy Info (EERE)

    Name: MIT- Earth Resources Laboratory Address: 77 Massachusetts Avenue Place: Cambridge, Massachusetts Zip: 02139 Region: Greater Boston Area Website: eaps.mit.eduerl...

  1. MIT- Electrochemical Energy Laboratory | Open Energy Information

    Open Energy Info (EERE)

    Name: MIT- Electrochemical Energy Laboratory Address: 77 Massachusetts Avenue Place: Cambridge, Massachusetts Zip: 02139 Region: Greater Boston Area Website: web.mit.edueel...

  2. R and D Programs and Policy within the CEA-AREVA Joint Vitrification Lab (LCV) - 13592

    SciTech Connect (OSTI)

    Piroux, Jean Christophe [AREVA NC Marcoule LCV (France)] [AREVA NC Marcoule LCV (France); Paradis, Luc; Ladirat, Christian [CEA Marcoule LCV (France)] [CEA Marcoule LCV (France); Brueziere, Jerome; Chauvin, Eric [AREVA NC Paris La Defense (France)] [AREVA NC Paris La Defense (France)

    2013-07-01

    Waste management is a key issue for the reprocessing industry; furthermore, vitrification is considered as the reference for nuclear waste management. In order to further improve and strengthen their historical cooperation in high temperature waste management, the CEA, R and D organization, and AREVA, Industrial Operator, decided, in September 2010, to create a Joint Vitrification Laboratory within the framework of a strategic partnership. The main objectives of the CEA-AREVA Joint Vitrification Laboratory (LCV) are (i) support AREVA's activities, notably in its La Hague plants and for new projects, (ii) strengthen the CEA's lead as a reference laboratory in the field of waste conditioning. The LCV is mandated to provide strong, innovative solutions through the performance of R and D on processes and materials for vitrification, fusion and incineration, for high, intermediate and low level waste. The activities carried out in the LCV include academic research on containment matrices (formulation, long-term behaviour), and the improvement of current technologies/development of new ones in lab-scale to full-scale pilot facilities, in non-radioactive and radioactive conditions, including modelling and experimental tools. This paper focuses on the programs and policy managed within the LCV, as well as the means employed by the CEA and AREVA to meet common short-,mid- and long-term challenges, from a scientific and industrial point of view. Among other things, we discuss the technical support provided for the La Hague vitrification facilities on hot melter and CCIM technologies, the start-up of new processes (decommissioning effluents, UMo FP) with CCIM, the preparation of future processes by means of an assessment of new technologies and containment matrices (improved glasses, ceramics, etc.), as well as incineration/vitrification for organic and metallic mixed waste or metallic fusion. The close relationship between the R and D teams and industrial operators enables the LCV to propose attractive waste management solutions, with appropriate schedules and optimized development costs, making allowance for R and D constraints, engineering requirements and the industrial environment. (authors)

  3. Multifunction Instrument Tree (MIT) Neutron and Gamma Probe Acceptance for Beneficial Use (ABU)

    SciTech Connect (OSTI)

    CANNON, N.S.

    1999-08-08

    The multifunction instrument tree (MIT) probe program has been developed to modify existing Liquid Observation Well (LOW) neutron and gamma probes for use in the validation shafts of the two MITs installed in Tank 241-SY-101. One of the program objectives is that the modified MIT probes be completely compatible with the existing LOW van instrumentation and procedures. The major program objective is to produce neutron and gamma scans from Tank 241-SY-101 that would assist in evaluating waste feature structure and elevation. The MIT probe program is described in greater detail in the engineering task plan (HNF-3322). In accordance with the engineering task plan, a test plan (HNF-3595) was written, reduced diameter (allowing insertion into the MIT validation tube) neutron and gamma probes were acquired, an acceptance and operational test procedure (HNF-3838) was written, acceptance and operational testing of the MIT probes was performed, and a report of these test results (HNF-4369) has been issued. A number of neutron and gamma probe scans have been obtained from the Tank 241-SY-101 MITs, starting on February 8, 1999, in cooperation with Operations. Now that the MIT probes are fully demonstrated, this document transfers ownership of these probes to Operations, utilizing the final acceptance for beneficial use (ABU) form that follows in Section 3.0.

  4. MIT-CTP/4229 Effective Field Theory

    Office of Scientific and Technical Information (OSTI)

    Field Theory of Fractional Quantized Hall Nematics Michael Mulligan, 1 Chetan Nayak, 2 and Shamit Kachru 3 1 Center for Theoretical Physics, MIT, Cambridge, MA 02139, USA 2...

  5. Alumni: Alexia Schulz, MIT Lincoln Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2015 all issues All Issues submit Alumni: Alexia Schulz, MIT Lincoln Laboratory Big data helps solve big problems September 1, 2015 Alexia Schulz Alexia Schulz Contact...

  6. Reaching Underground Sources (from MIT Energy Initiative's Energy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reaching Underground Sources (from MIT Energy Initiative's Energy Futures, Spring 2012) American Fusion News Category: Massachusetts Institute of Technology (MIT) Link: Reaching ...

  7. MIT- Center for Transportation and Logistics | Open Energy Information

    Open Energy Info (EERE)

    MIT- Center for Transportation and Logistics Address: 77 Massachusetts Avenue Place: Cambridge, Massachusetts Zip: 02139 Region: Greater Boston Area Website: ctl.mit.edu...

  8. MIT- Center for 21st Century Energy | Open Energy Information

    Open Energy Info (EERE)

    Name: MIT- Center for 21st Century Energy Address: 77 Massachusetts Avenue Place: Cambridge, Massachusetts Zip: 02139 Region: Greater Boston Area Website: web.mit.educ21ce...

  9. MIT - Center for Advanced Nuclear Energy Systems | Open Energy...

    Open Energy Info (EERE)

    - Center for Advanced Nuclear Energy Systems Jump to: navigation, search Logo: MIT - Center for Advanced Nuclear Energy Systems Name: MIT - Center for Advanced Nuclear Energy...

  10. MIT- Energy Science and Engineering Laboratory | Open Energy...

    Open Energy Info (EERE)

    Science and Engineering Laboratory Jump to: navigation, search Logo: MIT- Energy Science and Engineering Laboratory Name: MIT- Energy Science and Engineering Laboratory Address: 77...

  11. DOE-NE Light Water Reactor Sustainability Program and EPRI Long-Term Operations Program. Joint Research and Development Plan

    SciTech Connect (OSTI)

    Williams, Don

    2014-04-01

    Nuclear power has contributed almost 20% of the total amount of electricity generated in the United States over the past two decades. High capacity factors and low operating costs make nuclear power plants (NPPs) some of the most economical power generators available. Further, nuclear power remains the single largest contributor (nearly 70%) of non-greenhouse gas-emitting electric power generation in the United States. Even when major refurbishments are performed to extend operating life, these plants continue to represent cost-effective, low-carbon assets to the nation’s electrical generation capability. By the end of 2014, about one-third of the existing domestic fleet will have passed their 40th anniversary of power operations, and about one-half of the fleet will reach the same 40-year mark within this decade. Recognizing the challenges associated with pursuing extended service life of commercial nuclear power plants, the U.S. Department of Energy’s (DOE) Office of Nuclear Energy (NE) and the Electric Power Research Institute (EPRI) have established separate but complementary research and development programs (DOE-NE’s Light Water Reactor Sustainability [LWRS] Program and EPRI’s Long-Term Operations [LTO] Program) to address these challenges. To ensure that a proper linkage is maintained between the programs, DOE-NE and EPRI executed a memorandum of understanding in late 2010 to “establish guiding principles under which research activities (between LWRS and LTO) could be coordinated to the benefit of both parties.” This document represents the third annual revision to the initial version (March 2011) of the plan as called for in the memorandum of understanding.

  12. U.S. Department of Energy and the MIT Energy Initiative Announce a Women in

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Energy Program for United States | Department of Energy the MIT Energy Initiative Announce a Women in Clean Energy Program for United States U.S. Department of Energy and the MIT Energy Initiative Announce a Women in Clean Energy Program for United States April 26, 2012 - 10:00am Addthis LONDON -- At the Third Clean Energy Ministerial in London today, the U.S. Department of Energy announced a three-part plan to help implement the Clean Energy Education and Empowerment initiative or

  13. The role of the U.S. Clean Coal Technology Program in implementing the objectives of the joint Canada-U.S. acid rain mitigation initiative

    SciTech Connect (OSTI)

    Baldwin, A.L.; Smith, D.N.; Mann, A.W.; McIlvried, H.G.; Russell, D.L. Sr.

    1997-12-31

    The Clean Coal Technology (CCT) Program was initiated by the US Department of Energy (DOE) in part as a response to the 1986 Joint Report of the US and Canadian Special Envoys on Acid Rain, with a particular focus on coal-burning electric power plants. The fist three solicitations of the CCT Program were aimed primarily at mitigating the potential impacts of acid rain. Subsequently, the Clean Air Act Amendments of 1990 established emission reduction targets for SO{sub 2} and No{sub x}, which influenced the goals of the last two CCT Program. This paper provides an overview of the CCT Program and reports the significant results, with emphasis on emissions reduction as well as their impact on ozone formation.

  14. MIT's Plasma Science Fusion Center: Tokamak Experiments Come Clean about

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Impurity Transport | Princeton Plasma Physics Lab Tokamak Experiments Come Clean about Impurity Transport American Fusion News Category: Massachusetts Institute of Technology (MIT) Link: MIT's Plasma Science Fusion Center: Tokamak Experiments Come Clean about Impurity Transport

  15. Massachusetts Institute of Technology (MIT) | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Massachusetts Institute of Technology (MIT) Subscribe to RSS - Massachusetts Institute of Technology (MIT) Massachusetts Institute of Technology (MIT) Image: Massachusetts Institute of Technology (MIT) Applying physics, teamwork to fusion energy science Read more about Applying physics, teamwork to fusion energy science A Tour of Plasma Physics in Downtown Cambridge Read more about A Tour of Plasma Physics in Downtown Cambridge Placing Fusion Power on a Pedestal Read more about Placing Fusion

  16. Ed Jascevsky Safety Division ChIcago Operations Office MIT CONTFACT INFCE"ATION

    Office of Legacy Management (LM)

    ;/:4,4 (; . 1.; e octo: ' J : 18, 1976 Ed Jascevsky Safety Division ChIcago Operations Office MIT CONTFACT INFCE"ATION During the discussions on October 8, 1976, you iquired about information relative to work done by MIT as background infomation for survey planning. The enclosed information is parephrased frorc an unpublished history of program work carried out by the Process Eevclopncnt Group of the Dl.ti,si.on of Raw Katerids, I believe this work was done under contract nuder AT(30-1)956.

  17. Ceramic joints

    DOE Patents [OSTI]

    Miller, Bradley J. (Worcester, MA); Patten, Jr., Donald O. (Sterling, MA)

    1991-01-01

    Butt joints between materials having different coefficients of thermal expansion are prepared having a reduced probability of failure of stress facture. This is accomplished by narrowing/tapering the material having the lower coefficient of thermal expansion in a direction away from the joint interface and not joining the narrow-tapered surface to the material having the higher coefficient of thermal expansion.

  18. Joint environmental assessment 1997--2001 of the California Department of Food and Agriculture Curly Top Virus Control Program for Bureau of Land Management and Department of Energy

    SciTech Connect (OSTI)

    1997-03-01

    The DOE, Naval Petroleum reserves in California (NPRC), proposes to sign an Amendment to the Cooperative Agreement and Supplement with the California Department of Food and Agriculture (CDFA) to extend the term of the Curly Top Virus Control Program (CTVCP) in California. This program involves Malathion spraying on NPRC lands to control the beet leafhopper, over a five year period from 1997 through 2001. It is expected that approximately 330 acres on Naval Petroleum Reserve Number 1 (NPR-1) and approximately 9,603 acres on Naval Petroleum Reserve Number 2 (NPR-2) will be treated with Malathion annually by CDFA during the course of this program. The actual acreage subject to treatment can vary from year to year. Pursuant to the requirements of the National Environmental Policy Act of 1969 (NEPA), as amended, the potential impacts of the proposed action were analyzed in a Joint Environmental Assessment (DOE/EA-1011) with the US Department of Interior, Bureau of Land Management (BLM) acting as lead agency, in consultation with the CDFA, and the DOE acting as a cooperating agency. Based on the analysis in the EA, DOE has determined that the conduct of the Curly Top Virus Control Program in California is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the NEPA. Therefore, the preparation of an Environmental Impact Statement is not required and DOE is consequently issuing a FONSI.

  19. What's Next for Nuclear Energy? MIT Students Discuss Path Forward

    Broader source: Energy.gov [DOE]

    Students at Massachusetts Institute of Technology (MIT) gathered Friday to have a casual discussion with the U.S. government’s foremost expert on nuclear energy

  20. MIT-Alliance for Global Sustainability | Open Energy Information

    Open Energy Info (EERE)

    Name: MIT-Alliance for Global Sustainability Address: 77 Massachusetts Avenue Place: Cambridge, Massachusetts Zip: 02139 Region: Greater Boston Area Website: globalsustainability....

  1. Massachusetts Institute of Technology MIT | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search Name: Massachusetts Institute of Technology (MIT) Place: Cambridge, Massachusetts Zip: 02139 4307 Product: Private research university located in...

  2. MIT- Deshpande Center for Technological Innovation | Open Energy...

    Open Energy Info (EERE)

    Deshpande Center for Technological Innovation Address: 77 Massachusetts Avenue Place: Cambridge, Massachusetts Zip: 02139 Region: Greater Boston Area Website: web.mit.edu...

  3. MIT Emissions Prediction and Policy Analysis (EPPA) Model | Open...

    Open Energy Info (EERE)

    Website: dspace.mit.eduhandle1721.129790 Cost: Free Related Tools Global Atmospheric Pollution Forum Air Pollutant Emission Inventory ClearPath Global Relationship Assessment...

  4. Joint Announcement

    Broader source: Energy.gov (indexed) [DOE]

    institution or organization are encouraged to do so, or to check their institution's web site for information, and then contact their agency program officer, or agency contacts...

  5. The US DOE/MIT Innovation Acceleration Competition

    SciTech Connect (OSTI)

    2009-06-30

    The Competition asked student teams from several US Universities to propose business models, technological systems, and policy framework to accelerate the penetration of new vehicle and fuel technologies into the markets. In May 2009 the final selection of teams was announced and four of five finalist teams flew to Washington DC to present to the US Department of Energy. The five finalist teams were 1. Filter Sensing Technologies (FST) (MIT), 2. Flex Cathode Technology for Electric Vehicle Batteries, 3. Green Guidance (RPI), 4. Levant Power (MIT), and 5. Wind-Driven Paddlewheel Cylinder for Energy Storage in Freighter Trucks (Villanova). The five finalists?? entries are described.

  6. Joint Implementation Network (JIN) | Open Energy Information

    Open Energy Info (EERE)

    2.2 JIN Programs 3 References About Joint Implementation Network (JIN) was established in 1995 as knowledge centre for climate change policy issues in general and the concept of...

  7. Joint Environmental Management System (EMS) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Environmental Management System (EMS) Joint Environmental Management System (EMS) Joint Environmental Management System (EMS) The environmental management system (EMS) has two areas of focus: environmental compliance and environmental sustainability. The environmental compliance aspect of the EMS consists of regulatory compliance and monitoring programs that implement federal, state, local, and tribal requirements; agreements; and permits under the Legacy Management contract. The

  8. Large displacement spherical joint

    DOE Patents [OSTI]

    Bieg, Lothar F. (Albuquerque, NM); Benavides, Gilbert L. (Albuquerque, NM)

    2002-01-01

    A new class of spherical joints has a very large accessible full cone angle, a property which is beneficial for a wide range of applications. Despite the large cone angles, these joints move freely without singularities.

  9. 2014 Joint Action Workshop

    Broader source: Energy.gov [DOE]

    The Joint Action Workshop is an annual event for joint action agencies and their members to meet informally and discuss emerging policy, regulatory, and power supply issues, and other topics...

  10. Joint DOE-Rosatom Statement

    Office of Environmental Management (EM)

    Joint Statement on the U.S. - Russian Excess Weapon-grade Plutonium Disposition Program The U.S. Department of Energy (DOE) and the Federal Atomic Energy Agency, Russian Federation (Rosatom), as the Executive Agents for the implementation of the 2000 Plutonium Management and Disposition Agreement, hereby reaffirm their commitment to implementing the 2000 Agreement and effective and transparent disposition of 34 metric tons each of weapon- grade plutonium designated as no longer required for

  11. Research investigations in oil shale, tar sand, coal research, advanced exploratory process technology, and advanced fuels research: Volume 2 -- Jointly sponsored research program. Final report, October 1986--September 1993

    SciTech Connect (OSTI)

    Smith, V.E.

    1994-09-01

    Numerous studies have been conducted in five principal areas: oil shale, tar sand, underground coal gasification, advanced process technology, and advanced fuels research. In subsequent years, underground coal gasification was broadened to be coal research, under which several research activities were conducted that related to coal processing. The most significant change occurred in 1989 when the agreement was redefined as a Base Program and a Jointly Sponsored Research Program (JSRP). Investigations were conducted under the Base Program to determine the physical and chemical properties of materials suitable for conversion to liquid and gaseous fuels, to test and evaluate processes and innovative concepts for such conversions, to monitor and determine environmental impacts related to development of commercial-sized operations, and to evaluate methods for mitigation of potential environmental impacts. This report is divided into two volumes: Volume 1 consists of 28 summaries that describe the principal research efforts conducted under the Base Program in five topic areas. Volume 2 describes tasks performed within the JSRP. Research conducted under this agreement has resulted in technology transfer of a variety of energy-related research information. A listing of related publications and presentations is given at the end of each research topic summary. More specific and detailed information is provided in the topical reports referenced in the related publications listings.

  12. National Clean Energy Business Plan Competition: Unified Solar Wins at MIT

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Energy Prize | Department of Energy Unified Solar Wins at MIT Clean Energy Prize National Clean Energy Business Plan Competition: Unified Solar Wins at MIT Clean Energy Prize May 2, 2014 - 11:01am Addthis Unified Solar's integrated circuit solution helps reduce energy loss for solar panels. The student team from Massachusetts Institute of Technology won the MIT Clean Energy Prize earlier this week. | Photo courtesy of Unified Solar Unified Solar's integrated circuit solution helps

  13. President Obama Visits MIT EFRC | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    President Obama Visits MIT EFRC Energy Frontier Research Centers (EFRCs) EFRCs Home Centers Research Science Highlights News & Events EFRC News EFRC Events DOE Announcements Publications History Contact BES Home 10.23.09 President Obama Visits MIT EFRC Print Text Size: A A A Subscribe FeedbackShare Page Oct 23, 2009 :: President Obama spoke with Marc Baldo, director of the Center for Excitonics, and EFRC member Vladimir Bulovic about their clean energy research during his visit to MIT

  14. INTRODUCTION TO SCINTILLATION LIGHT IN LIQUID ARGON Ben Jones, MIT

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TO SCINTILLATION LIGHT IN LIQUID ARGON Ben Jones, MIT The Basics: Light yield ~ few 10,000's of photons per MeV (dependences on E field, particle type and purity) Wavelength of emission is 128nm Light with two characteristic time constants: - fast component, 6 ns - slow component,1500 ns Argon is highly transparent to its own scintillation light. J Chem Phys vol 91 (1989) 1469 E Morikawa et al Mechanisms of Scintillation in LAr In liquid argon, there are two important scintillation mechanisms:

  15. DOEs Effort to Reduce Truck Aerodynamic Drag through Joint...

    Energy Savers [EERE]

    to Reduce Truck Aerodynamic Drag through Joint Experiments and Computations 2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and...

  16. WIPP - Joint Information Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Joint Information Center is located at 4021 National Parks Highway in Carlsbad, N.M. Joint Information Center In the unlikely event of an emergency, the WIPP Joint Information Center (JIC) serves as a central control point to coordinate multi-agency efforts to issue timely and accurate information to the public, news media and project employees. Emergency contact information: The public If the JIC is activated, members of the general public, including family members, may call (575) 234-7380

  17. Laboratory program helps small businesses

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lab helps small businesses Laboratory program helps small businesses The free program, run jointly by Los Alamos and Sandia National Laboratories, leverages the laboratories'...

  18. MIT's Plasma Science Fusion Center: I-Mode Powers Up on Alcator C-Mod

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tokamak | Princeton Plasma Physics Lab I-Mode Powers Up on Alcator C-Mod Tokamak American Fusion News Category: Massachusetts Institute of Technology (MIT) Link: MIT's Plasma Science Fusion Center: I-Mode Powers Up on Alcator C-Mod Tokamak

  19. Joint Center for Artificial Photosynthesis

    ScienceCinema (OSTI)

    Koval, Carl; Lee, Kenny; Houle, Frances; Lewis, Nate

    2013-12-19

    The Joint Center for Artificial Photosynthesis (JCAP) is the nation's largest research program dedicated to the development of an artificial solar-fuel generation technology. Established in 2010 as a U.S. Department of Energy (DOE) Energy Innovation Hub, JCAP aims to find a cost-effective method to produce fuels using only sunlight, water, and carbon dioxide as inputs. JCAP brings together more than 140 top scientists and researchers from the California Institute of Technology and its lead partner, Berkeley Lab, along with collaborators from the SLAC National Accelerator Laboratory, and the University of California campuses at Irvine and San Diego.

  20. Don-Hyung Ha > Postdoc - MIT (Shao-Horn Group) > Center Alumni > The Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Materials Center at Cornell Don-Hyung Ha Postdoc - MIT (Shao-Horn Group) dhha@mit.edu Formerly a graduate student with the Robinson Group, he received his PhD in September 2014. He continues his research as a member of the Electrochemical Energy Lab at MIT under the leadership for Professor Yang Shao-Horn

  1. Programming

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Programming Programming Compiling and linking programs on Euclid. Compiling Codes How to compile and link MPI codes on Euclid. Read More » Using the ACML Math Library How to compile and link a code with the ACML library and include the $ACML environment variable. Read More » Process Limits The hard and soft process limits are listed. Read More » Last edited: 2016-02-01 08:07:27

  2. Programming

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    This page provides examples of compilation and running scripts when mixing CC++ with Fortran codes. Read More Programming Tuning Options Tips for tuning performance on the...

  3. Joint Facilities User Forum

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    User Forum on Data-Intensive Computing Panel: 20 Minutes Into Our Future Near-term technology panel discussion between facility operations, applications developer, and users 2 Joint Facilities User Forum Guiding Thoughts of this Panel * Talking to the Compute, Store, Analyze cycle - Users - Developers - Operators/integrators * What problems have we solved? * What problems have we found? * How do we inspire interesting dinner conversation for participants? 3 Joint Facilities User Forum Format *

  4. High pressure ceramic joint

    DOE Patents [OSTI]

    Ward, Michael E. (Poway, CA); Harkins, Bruce D. (San Diego, CA)

    1993-01-01

    Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present joint when used with recuperators increases the use of ceramic components which do not react to highly corrosive gases. Thus, the present joint used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present joint is comprised of a first ceramic member, a second ceramic member, a mechanical locking device having a groove defined in one of the first ceramic member and the second ceramic member. The joint and the mechanical locking device is further comprised of a refractory material disposed in the groove and contacting the first ceramic member and the second ceramic member. The present joint mechanically provides a high strength load bearing joint having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

  5. High pressure ceramic joint

    DOE Patents [OSTI]

    Ward, M.E.; Harkins, B.D.

    1993-11-30

    Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present joint when used with recuperators increases the use of ceramic components which do not react to highly corrosive gases. Thus, the present joint used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present joint is comprised of a first ceramic member, a second ceramic member, a mechanical locking device having a groove defined in one of the first ceramic member and the second ceramic member. The joint and the mechanical locking device is further comprised of a refractory material disposed in the groove and contacting the first ceramic member and the second ceramic member. The present joint mechanically provides a high strength load bearing joint having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures. 4 figures.

  6. GE Scientists Source Best Ideas at hackMIT | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Scientists Source Best Ideas at hackMIT Click to email this to a friend (Opens in new window) Share on Facebook (Opens in new window) Click to share (Opens in new window) Click to share on LinkedIn (Opens in new window) Click to share on Tumblr (Opens in new window) GE Scientists Source Best Ideas at hackMIT Joseph Salvo 2013.10.03 At MIT they're serious about "hacking" together ideas for innovation, invention, and new businesses. This weekend a team from GE Global Research and GE

  7. Programming

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    using MPI and OpenMP on NERSC systems, the same does not always exist for other supported parallel programming models such as UPC or Chapel. At the same time, we know that these...

  8. Programming

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    provided on the Cray systems at NERSC. The Programming Environment is managed by a meta-module named similar to "PrgEnv-gnu4.6". The "gnu" indicates that it is providing the...

  9. Programming

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Programming Programming Compiling Codes There are three compiler suites available on Carver: Portland Group (PGI), Intel, and GCC. The PGI compilers are the default, to provide compatibility with other NERSC platforms. Read More » Using MKL Intel's Math Kernel Library (MKL) is a library of highly optimized, extensively threaded math routines optimized for Intel processors. Core math functions include BLAS, LAPACK, ScaLAPACK, Sparse Solvers, Fast Fourier Transforms, Vector Math, and more. It is

  10. Statement from Secretary Moniz on Adoption Day for the Joint...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in nature. Today, as the Joint Comprehensive Plan of Action (JCPOA) comes into effect, Iran will begin taking substantial and verifiable steps to roll back its nuclear program and...

  11. Russian Health Studies Program - Joint Coordinating Committee...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Which institutions in Russia are currently participating in JCCRER activities? Southern Urals Biophysics Institute (SUBI), Ozersk Mayak Production Association, Ozersk Urals ...

  12. Dish-Stirling Joint Venture Program

    SciTech Connect (OSTI)

    1993-12-31

    A brief report about DOE/Sandia National Laboratories/Cummins Engine Company dish-Stirling solar electric engine system being perfected.

  13. Program

    Office of Scientific and Technical Information (OSTI)

    Extremophiles 2004 5th International Conference on Extremophiles SEPTEMBER 19 -23, 2004 CAMBRIDGE, MARYLAND Extremophiles 2004 5th International Conference on Extremophiles © 2004, American Society for Microbiology 1752 N Street, N.W. Washington, DC 20036-2904 Phone: 202-737-3600 World Wide Web: www.asm.org All Rights Reserved Printed in the United States of America ISBN: 1-55581 324-0 TABLE OF CONTENTS General Information Scientific Program Abstracts for Oral Sessions Abstracts for Poster

  14. MIT Plasma Science & Fusion Center: research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research Program Information Publications & News Meetings & Seminars Contact Information Physics Research Fusion Technology & Engineering Plasma Technology Waves & Beams Useful...

  15. MIT Plasma Science & Fusion Center: research, alcator, publications...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research Program Information Publications & News Meetings & Seminars Contact Information Physics Research High-Energy- Density Physics Waves & Beams Technology & Engineering...

  16. Vehicle Technologies Office Merit Review 2015: Joint Development and Coordination of Emissions Control Data and Models

    Broader source: Energy.gov [DOE]

    Presentation given by Oak Ridge National Laboratory at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about joint...

  17. Business Energy Conservation Loan Program | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    vermo... State Vermont Program Type Loan Program Summary The Vermont Business Energy Conservation Loan Program is a joint-effort between Efficiency Vermont and the...

  18. Gamesa Santana Joint Venture | Open Energy Information

    Open Energy Info (EERE)

    Gamesa Santana Joint Venture Place: Spain Sector: Wind energy Product: Wind turbine manufacturing joint venture in Spain. References: Gamesa Santana Joint Venture1 This article...

  19. Double slotted socket spherical joint

    DOE Patents [OSTI]

    Bieg, Lothar F.; Benavides, Gilbert L.

    2001-05-22

    A new class of spherical joints is disclosed. These spherical joints are capable of extremely large angular displacements (full cone angles in excess of 270.degree.), while exhibiting no singularities or dead spots in their range of motion. These joints can improve or simplify a wide range of mechanical devices.

  20. Safety Monitor Joint Working Group (JWG) Tour

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 th Meeting of the Joint Working Group of the U.S.-Japan Coordinating Committee of Fusion Energy on Safety in Inter-Institutional Collaborations (U.S.-Japan Safety Monitoring Program) Meeting in Japan, July 29-August 2, 2013 Submitted: October 16, 2013 Respectfully submitted to: Barry Sullivan Program Manager - ES&H U.S. DOE - Office of Fusion Energy Sciences Professor Kiyohiko Nishimura Head of Division for Health and Safety Management National Institute for Fusion Science Prepared by: Lee

  1. Stochastic Joint Inversion for Integrated Data Interpretation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Stochastic Joint Inversion for Integrated Data Interpretation in Geothermal Exploration Stochastic Joint Inversion for Integrated Data Interpretation in Geothermal Exploration ...

  2. Joint Actinide Shock Physics Experimental Research | National...

    National Nuclear Security Administration (NNSA)

    Actinide Shock Physics Experimental Research | National Nuclear Security Administration ... Facilities Joint Actinide Shock Physics Experimental Research Joint Actinide ...

  3. Meeting the Next Generation of Energy Entrepreneurs at MIT Showcase...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    May 6, 2011 - 12:50pm Addthis David Moore Presidential Management Fellow, Office of Energy ... David Moore is an Energy Technology Program Specialist in the Office of Energy Efficiency ...

  4. National Clean Energy Business Plan Competition: OptiBit Wins MIT Clean

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Prize | Department of Energy OptiBit Wins MIT Clean Energy Prize National Clean Energy Business Plan Competition: OptiBit Wins MIT Clean Energy Prize May 14, 2015 - 9:53am Addthis OptiBit’s product brings the high bandwidth and energy efficiency of fiber optics to computer chips, helping data centers keep up with ballooning volumes of electronic information while saving energy. | <em>Photo courtesy of OptiBit</em> OptiBit's product brings the high bandwidth and energy

  5. Operation Ivy. Joint Task Force 132, 1952. Final report

    SciTech Connect (OSTI)

    Not Available

    1985-09-01

    This report covers the activities of the Joint Task Force 132 in Operation Ivy, in 1952 at Eniwetok Atoll. Shots Mike and King were detonated in conjunction with eleven experimental programs. This report describes the device, weapon, and experimental programs, giving as many preliminary conclusions as can be drawn from early analysis of the data.

  6. Integrated Global System Modeling Framework | Open Energy Information

    Open Energy Info (EERE)

    System Modeling Framework AgencyCompany Organization: MIT Joint Program on the Science and Policy of Global Change Sector: Climate, Energy Focus Area: Renewable Energy...

  7. Metal to ceramic sealed joint

    DOE Patents [OSTI]

    Lasecki, J.V.; Novak, R.F.; McBride, J.R.

    1991-08-27

    A metal to ceramic sealed joint which can withstand wide variations in temperature and maintain a good seal is provided for use in a device adapted to withstand thermal cycling from about 20 to about 1000 degrees C. The sealed joint includes a metal member, a ceramic member having an end portion, and an active metal braze forming a joint to seal the metal member to the ceramic member. The joint is positioned remote from the end portion of the ceramic member to avoid stresses at the ends or edges of the ceramic member. The sealed joint is particularly suited for use to form sealed metal to ceramic joints in a thermoelectric generator such as a sodium heat engine where a solid ceramic electrolyte is joined to metal parts in the system. 11 figures.

  8. Metal to ceramic sealed joint

    DOE Patents [OSTI]

    Lasecki, John V. (Livonia, MI); Novak, Robert F. (Farmington Hills, MI); McBride, James R. (Ypsilanti, MI)

    1991-01-01

    A metal to ceramic sealed joint which can withstand wide variations in temperature and maintain a good seal is provided for use in a device adapted to withstand thermal cycling from about 20 to about 1000 degrees C. The sealed joint includes a metal member, a ceramic member having an end portion, and an active metal braze forming a joint to seal the metal member to the ceramic member. The joint is positioned remote from the end portion of the ceramic member to avoid stresses at the ends or edges of the ceramic member. The sealed joint is particularly suited for use to form sealed metal to ceramic joints in a thermoelectric generator such as a sodium heat engine where a solid ceramic electrolyte is joined to metal parts in the system.

  9. PNNL: About PNNL - Joint Appointments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Joint Appointments Thom Dunning Thom Dunning co-leads the Northwest Institute for Advanced Computing, a partnership of PNNL and the University of Washington. We value joint appointments with American universities and with colleagues who are leaders in their fields. Joint appointments increase both parties' access to new funding sources, graduate students, training opportunities, and unique instrumentation and facilities. They provide scientists with greater opportunities for multidisciplinary

  10. Adhesive joint and composites modeling in SIERRA.

    SciTech Connect (OSTI)

    Ohashi, Yuki; Brown, Arthur A.; Hammerand, Daniel Carl; Adolf, Douglas Brian; Chambers, Robert S.; Foulk, James W., III

    2005-11-01

    Polymers and fiber-reinforced polymer matrix composites play an important role in many Defense Program applications. Recently an advanced nonlinear viscoelastic model for polymers has been developed and incorporated into ADAGIO, Sandia's SIERRA-based quasi-static analysis code. Standard linear elastic shell and continuum models for fiber-reinforced polymer-matrix composites have also been added to ADAGIO. This report details the use of these models for advanced adhesive joint and composites simulations carried out as part of an Advanced Simulation and Computing Advanced Deployment (ASC AD) project. More specifically, the thermo-mechanical response of an adhesive joint when loaded during repeated thermal cycling is simulated, the response of some composite rings under internal pressurization is calculated, and the performance of a composite container subjected to internal pressurization, thermal loading, and distributed mechanical loading is determined. Finally, general comparisons between the continuum and shell element approaches for modeling composites using ADAGIO are given.

  11. Joint Outreach Task Group Video Series | Department of Energy

    Energy Savers [EERE]

    Video Series Joint Outreach Task Group Video Series The purpose of this video series is to provide an overview of the roles and responsibilities of the federal government offices and entities involved in the Energy Employees Occupational Illness Compensation Program Act (EEOIOCPA) and the Former Worker Medical Screening Program (FWP), two programs that serve eligible workers from the Department of Energy (DOE). In the interest of combining resources, since both the EEOICPA and FWP serve a

  12. Sustainable Agriculture Loan Program

    Broader source: Energy.gov [DOE]

    Loans are available in amounts of up to $40,000 per farm family, with up to $160,000 ($40,000 per farmer) available for joint projects. The program currently offers a fixed interest rate of 3%...

  13. Method of forming a joint

    DOE Patents [OSTI]

    Butt, Darryl Paul; Cutler, Raymond Ashton; Rynders, Steven Walton; Carolan, Michael Francis

    2006-08-22

    A method of joining at least two sintered bodies to form a composite structure, including providing a first multicomponent metallic oxide having a perovskitic or fluorite crystal structure; providing a second sintered body including a second multicomponent metallic oxide having a crystal structure of the same type as the first; and providing at an interface a joint material containing at least one metal oxide containing at least one metal identically contained in at least one of the first and second multicomponent metallic oxides. The joint material is free of cations of Si, Ge, Sn, Pb, P and Te and has a melting point below the sintering temperatures of both sintered bodies. The joint material is heated to a temperature above the melting point of the metal oxide(s) and below the sintering temperatures of the sintered bodies to form the joint. Structures containing such joints are also disclosed.

  14. Shock transmissibility of threaded joints

    SciTech Connect (OSTI)

    Hansen, N.R.; Bateman, V.I.; Brown, F.A.

    1996-12-31

    Sandia National Laboratories (SNL) designs mechanical systems with threaded joints that must survive high shock environments. These mechanical systems include penetrators that must survive soil and rock penetration; drilling pipe strings that must survive rock-cutting, shock environments; and laydown weapons that must survive delivery impact shock. This paper summarizes an analytical study and an experimental evaluation of compressive, one-dimensional, shock transmission through a threaded joint in a split Hopkinson bar configuration. Thread geometries were scaled to simulate large diameter threaded joints with loadings parallel to the axis of the threads. Both strain and acceleration were evaluated with experimental measurements and analysis. Analytical results confirm the experimental conclusions that in this split Hopkinson bar configuration, the change in the one-dimensional shock wave by the threaded joint is localized to a length equal to a few diameters` length beyond the threaded joint.

  15. Commercialization Programs | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Commercialization Programs Through our commercialization programs, the Innovation and Entrepreneurship Center (IEC) helps accelerate the transfer of renewable energy and energy efficiency technologies into the marketplace. Colorado Center for Renewable Energy Economic Development Formerly the Colorado Cleantech Initiative program, the Colorado Center for Renewable Energy Economic Development (CREED) is a joint effort between NREL, the State of Colorado, and affiliated stakeholders to provide

  16. Forces in bolted joints: analysis methods and test results utilized for

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    nuclear core applications (LWBR Development Program) (Technical Report) | SciTech Connect Forces in bolted joints: analysis methods and test results utilized for nuclear core applications (LWBR Development Program) Citation Details In-Document Search Title: Forces in bolted joints: analysis methods and test results utilized for nuclear core applications (LWBR Development Program) × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of

  17. Italy Joint Statement | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Italy Joint Statement Italy Joint Statement " U.S.-Italy Joint Statement prepared as part of the International Partnership for a Hydrogen Economy " PDF icon italy_joint_statement.pdf More Documents & Publications Joint Statement by Energy Ministers of G8, The People's Republic of China, India and The Republic of Korea (June 2008) Joint Statement by Energy Ministers of G8, The People's Republic of China, India and The Republic of Korea (Energy Efficiency)

  18. Microsoft Word - DOE-ID-13-008 MIT EC B2-5.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 SECTION A. Project Title: Infrastructure Upgrade (Minor) to the MITR Research Reactor in Support of Operational Safety - Massachusetts Institute of Technology - Nuclear Reactor Lab SECTION B. Project Description The objective of this proposal is to improve the MIT Research Reactor safety by (1) procuring and installing a gaseous tritium detector that will monitor for airborne releases from both the reactor's heavy water reflector and from in-core experiments involving potential salt reactor

  19. Nuclear Resonance Fluorescence at MIT | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    Resonance Fluorescence at MIT Nuclear Physics (NP) NP Home About Research Facilities Science Highlights Benefits of NP Applications of Nuclear Science Applications of Nuclear Science Archives Small Business Innovation / Technology Transfer Funding Opportunities Nuclear Science Advisory Committee (NSAC) Community Resources Contact Information Nuclear Physics U.S. Department of Energy SC-26/Germantown Building 1000 Independence Ave., SW Washington, DC 20585 P: (301) 903-3613 F: (301) 903-3833 E:

  20. Climate Leaders Joint Venture | Open Energy Information

    Open Energy Info (EERE)

    Leaders Joint Venture Jump to: navigation, search Name: Climate Leaders' Joint Venture Place: Dallas, Texas Product: Tudor Investment and Camco International have partnered to...

  1. Malibu Joint Venture | Open Energy Information

    Open Energy Info (EERE)

    Malibu Joint Venture Jump to: navigation, search Name: Malibu Joint Venture Place: Germany Sector: Solar Product: String representation "German utility ... e of next year." is too...

  2. Energy Employees Occupational Illness Compensation Program |...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Contact Information: U. S. Department of Energy Office of ... Avenue, SW Washington, D. C. 20585 Contact Program Manager Gregory Lewis Video Series Joint Outreach ...

  3. Joint Cray XT Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New User (@NUG 2014) BerkeleyGW2013 Edison Performance New User Training HPC Using GPUs Getting Started at NERSC Training -- Edison Getting Started at NERSC NERSC Training at SC12 Effective Use of Compilers Chemistry and Material Sciences Applications Object-Oriented Programming in Fortran 2003 Software Carpentry Bootcamp JGI Compute User Training Series NUG Training 2012 NERSC Training at SC11 Using Hadoop for HPC Applications Getting Started at NERSC NERSC Intro for Environmental Energy

  4. DOE Joint Genome Institute | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    DOE Joint Genome Institute Biological and Environmental Research (BER) BER Home About Research Biological Systems Science Division (BSSD) Genomic Science DOE Bioenergy Research Centers Bioimaging Technology DOE Joint Genome Institute Structural Biology Radiochemistry & Imaging Instrumentation Radiobiology: Low Dose Radiation Research DOE Human Subjects Protection Program Climate and Environmental Sciences Division (CESD) Research Abstracts Searchable Archive of BER Highlights External link

  5. Statement from Secretary Moniz on Implementation Day for the Joint

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Comprehensive Plan of Action | Department of Energy Statement from Secretary Moniz on Implementation Day for the Joint Comprehensive Plan of Action Statement from Secretary Moniz on Implementation Day for the Joint Comprehensive Plan of Action January 16, 2016 - 5:07pm Addthis News Media Contact (202) 586-4940 DOENews@hq.doe.gov Implementation Day is a milestone in the effort to ensure that Iran's nuclear program is exclusively peaceful in nature by blocking potential pathways to a bomb. As

  6. Statement from Energy Secretary Ernest Moniz on the Joint Comprehensive

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Plan of Action | Department of Energy Energy Secretary Ernest Moniz on the Joint Comprehensive Plan of Action Statement from Energy Secretary Ernest Moniz on the Joint Comprehensive Plan of Action July 14, 2015 - 7:27am Addthis NEWS MEDIA CONTACT (202) 586-4940 "Today's announcement between the P5+1 and Iran is a historic accomplishment. Building on the Lausanne framework, it will ensure that Iran's nuclear program is - and will remain - a peaceful one, or that the international

  7. Non-Destructive Inspection of Adhesive Bonds in Metal-Metal Joints |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Inspection of Adhesive Bonds in Metal-Metal Joints Non-Destructive Inspection of Adhesive Bonds in Metal-Metal Joints 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. PDF icon lm_15_moore.pdf More Documents & Publications FY 2008 Progress Report for Lightweighting Materials - 10. Nondestructive Evaluation FY 2009 Progress Report for Lightweighting Materials - 10.

  8. CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy 1 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation PDF icon ace022_daw_2011_o.pdf More Documents & Publications CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR CLEERS Coordination & Development of Catalyst Process Kinetic Data CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR

  9. Hydrogen & Fuel Cells Program Overview | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    & Fuel Cells Program Overview Hydrogen & Fuel Cells Program Overview 2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Joint Plenary PDF icon pl003_satyapal_joint_plenary_2011_o.pdf More Documents & Publications Hydrogen and Fuel Cells Program Overview: Hydrogen and Fuel Cells 2011 International Conference Fuel Cell Technologies Program - DOD-DOE Workshop: Shipboard APUs Overview EERE Fuel Cell Technologies Program

  10. Joint BioEnergy Institute

    SciTech Connect (OSTI)

    Keasling, Jay; Simmons, Blake; Tartaglino, Virginia; Baidoo, Edward; Kothari, Ankita

    2015-06-15

    The Joint BioEnergy Institute (JBEI) is a U.S. Department of Energy (DOE) Bioenergy Research Center dedicated to developing advanced biofuelsliquid fuels derived from the solar energy stored in plant biomass that can replace gasoline, diesel and jet fuels.

  11. Sustainable Electric Utility (SEU)- SREC Purchase Program

    Broader source: Energy.gov [DOE]

    SREC purchase program is a joint incentive of Delaware Division of Energy and Climate (DNREC) and the state’s Sustainable Energy Utility (SEU). The program offers a standard onetime payment of $450...

  12. United States and France Sign Joint Statement on Civil Liability...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and France Sign Joint Statement on Civil Liability for Nuclear Damage United States and France Sign Joint Statement on Civil Liability for Nuclear Damage PDF icon Joint Statement ...

  13. Digital Sofcell Digital Ultracap joint venture | Open Energy...

    Open Energy Info (EERE)

    Ultracap joint venture Jump to: navigation, search Name: Digital Sofcell - Digital Ultracap joint venture Product: Digital Sofcell will joint venture with Digital Ultracap to...

  14. CLEERS Coordination & Joint Development of Benchmark Kinetics...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR CLEERS Coordination & Development of Catalyst Process Kinetic...

  15. Research and development joint ventures

    SciTech Connect (OSTI)

    Not Available

    1984-01-01

    Three panels made up of members of Congress and representatives of research and high technology industries testified at a hearing held to consider H.R. 1952 and H.R. 3393, both bills dealing with joint venture policies that diminish US competitiveness. The bills are designed to eliminate disincentives stemming from antitrust concerns about joint research and development (R and D) activities and to encourage private investment in R and D. The witnesses were asked to evaluate and compare the potential of these bills to overcome institutional barriers and to stimulate capital formation. Three appendices with statements from the National Association of Manufacturers, the Semiconductor Industry Association, and the Institute of Electrical and Electronics Engineers submitted for the record follow the testimony of the eight witnesses. (DCK)

  16. Intermetallic Layers in Soldered Joints

    Energy Science and Technology Software Center (OSTI)

    1998-12-10

    ILAG solves the one-dimensional partial differential equations describing the multiphase, multicomponent, solid-state diffusion-controlled growth of intermetallic layers in soldered joints. This software provides an analysis capability for materials researchers to examine intermetallic growth mechanisms in a wide variety of defense and commercial applications involving both traditional and advanced materials. ILAG calculates the interface positions of the layers, as well as the spatial distribution of constituent mass fractions, and outputs the results at user-prescribed simulation times.

  17. Metal-ceramic joint assembly

    DOE Patents [OSTI]

    Li, Jian (New Milford, CT)

    2002-01-01

    A metal-ceramic joint assembly in which a brazing alloy is situated between metallic and ceramic members. The metallic member is either an aluminum-containing stainless steel, a high chromium-content ferritic stainless steel or an iron nickel alloy with a corrosion protection coating. The brazing alloy, in turn, is either an Au-based or Ni-based alloy with a brazing temperature in the range of 9500 to 1200.degree. C.

  18. DOC-DOE Joint China Mission Statement | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint China Mission Statement DOC-DOE Joint China Mission Statement DOC-DOE Joint China Mission Statement PDF icon DOC-DOE Joint China Mission Statement More Documents &...

  19. Joint Institute for Nanoscience Annual Report 2004

    SciTech Connect (OSTI)

    Baer, Donald R.; Campbell, Charles

    2005-02-01

    Due to the inherently interdisciplinary nature of nanoscience and nanotechnology, research in this arena is often significantly enhanced through creative cooperative activities. The Joint Institute for Nanoscience (JIN) is a venture of the University of Washington (UW) and Pacific Northwest National Laboratory (PNNL) to encourage and enhance high impact and high quality nanoscience and nanotechnology research that leverages the strengths and capabilities of both institutions, and to facilitate education in these areas. This report summarizes JIN award activities that took place during fiscal year 2004 and provides a historical list of JIN awardees, their resulting publications, and JIN-related meetings. Major portions of the JIN efforts and resources are dedicated to funding graduate students and postdoctoral research associates to perform research in collaborations jointly directed by PNNL staff scientists and UW professors. JIN fellowships are awarded on the basis of applications that include research proposals. They have been very successful in expanding collaborations between PNNL and UW, which have led to many excellent joint publications and presentations and enhanced the competitiveness of both institutions for external grant funding. JIN-based interactions are playing a significant role in creating new research directions and reshaping existing research programs at both the UW and PNNL. The JIN also co-sponsors workshops on Nanoscale Science and Technology, four of which have been held in Seattle and one in Richland. In addition to involving PNNL staff in various UW nanoscience courses and seminars, a National Science Foundation grant, Development of UW-PNL Collaborative Curriculums in Nano-Science and Technology, has allowed the development of three intensive short courses that are taught by UW faculty, PNNL staff, and faculty from other institutions, including Washington State University, the University of Idaho, Stanford University, and the University of Alaska. The JIN agreement recognizes that cooperation beyond UW and PNNL is highly valuable. Starting in early 2003, efforts were initiated to form a regional communication link called the Northwest Nanoscience and Nanotechnology Network (N4). In concept, N4 is a tool to encourage communication and help identify regional resources and nanoscience and technology activities.

  20. Joint Environmental Management System (EMS) Declaration of Conformance...

    Energy Savers [EERE]

    Services Environmental Management System Joint Environmental Management System (EMS) Declaration of Conformance Joint Environmental Management System (EMS) Declaration of...

  1. DOE-NE Light Water Reactor Sustainability Program and EPRI Long-Term

    Office of Environmental Management (EM)

    Operations Program - Joint Research and Development Plan | Department of Energy DOE-NE Light Water Reactor Sustainability Program and EPRI Long-Term Operations Program - Joint Research and Development Plan DOE-NE Light Water Reactor Sustainability Program and EPRI Long-Term Operations Program - Joint Research and Development Plan Nuclear power has contributed almost 20% of the total amount of electricity generated in the United States over the past two decades. High capacity factors and low

  2. Statement from Secretary Moniz on Adoption Day for the Joint Comprehensive

    Energy Savers [EERE]

    Plan of Action | Department of Energy Secretary Moniz on Adoption Day for the Joint Comprehensive Plan of Action Statement from Secretary Moniz on Adoption Day for the Joint Comprehensive Plan of Action October 18, 2015 - 1:34pm Addthis NEWS MEDIA CONTACT (202) 586-4940 "Adoption Day marks an important milestone in ensuring that Iran's nuclear program is exclusively peaceful in nature. Today, as the Joint Comprehensive Plan of Action (JCPOA) comes into effect, Iran will begin taking

  3. Vehicle Technologies Office Merit Review 2014: Joint Development and Coordination of Emissions Control Data and Models (CLEERS Analysis and Coordination)

    Broader source: Energy.gov [DOE]

    Presentation given by Oak Ridge National Laboratory at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about the joint...

  4. Joint DOE-Rosatom Statement

    Energy Savers [EERE]

    for the performance of technical analysis that will contribute to both governments' decision making on cooperation regarding Russia's program to implement the 2000 Agreement....

  5. Joint Outreach Task Group Calendar: September 2013

    Broader source: Energy.gov [DOE]

    Joint Outreach Task Group (JOTG)has created a monthly calendar of community events to facilitate interagency and community involvement in these events. September 2013

  6. Joint Convention | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Joint Convention U.S. Leads Fifth International Review Meeting on the Safety of Spent Fuel and Radioactive Waste Management at the IAEA VIENNA, AUSTRIA - Today, representatives...

  7. CLEERS Coordination & Joint Development of Benchmark Kinetics...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR Emissions Control for Lean Gasoline Engines NH3 generation...

  8. CLEERS Coordination & Joint Development of Benchmark Kinetics...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Catalyst Process Kinetic Data CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR Functionality of Commercial NOx Storage-Reduction Catalysts...

  9. High-temperature brazed ceramic joints

    DOE Patents [OSTI]

    Jarvinen, Philip O.

    1986-01-01

    High-temperature joints formed from metallized ceramics are disclosed wherein the metal coatings on the ceramics are vacuum sputtered thereon.

  10. Report on the 1ST Meeting of the Joint Working Group on

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Report on the 2 nd Meeting of the Joint Working Group on Safety for the U.S.-PRC Coordinating Committee of Fusion Energy (U.S.-PRC Safety Monitoring Program) Meeting in USA, November 4-17, 2010 A. PURPOSE The purpose of the 2nd meeting of the U.S.-China Joint Working Group on Safety was to informally evaluate the programmatic aspects of environmental, health and safety (ESH) programs in US fusion research facilities by touring laboratory areas and meeting with researchers and safety

  11. High temperature ceramic/metal joint structure

    DOE Patents [OSTI]

    Boyd, Gary L. (Tempe, AZ)

    1991-01-01

    A high temperature turbine engine includes a hybrid ceramic/metallic rotor member having ceramic/metal joint structure. The disclosed joint is able to endure higher temperatures than previously possible, and aids in controlling heat transfer in the rotor member.

  12. Savannah River Ecology Laboratory - Outreach Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program

  13. Savannah River Ecology Laboratory - Outreach Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program

  14. MODELING UNDERGROUND STRUCTURE VULNERABILITY IN JOINTED ROCK

    SciTech Connect (OSTI)

    R. SWIFT; D. STEEDMAN

    2001-02-01

    The vulnerability of underground structures and openings in deep jointed rock to ground shock attack is of chief concern to military planning and security. Damage and/or loss of stability to a structure in jointed rock, often manifested as brittle failure and accompanied with block movement, can depend significantly on jointed properties, such as spacing, orientation, strength, and block character. We apply a hybrid Discrete Element Method combined with the Smooth Particle Hydrodynamics approach to simulate the MIGHTY NORTH event, a definitive high-explosive test performed on an aluminum lined cylindrical opening in jointed Salem limestone. Representing limestone with discrete elements having elastic-equivalence and explicit brittle tensile behavior and the liner as an elastic-plastic continuum provides good agreement with the experiment and damage obtained with finite-element simulations. Extending the approach to parameter variations shows damage is substantially altered by differences in joint geometry and liner properties.

  15. U.S. Department of Energy Vehicle Technologies Program Overview |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 1 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Joint Plenary PDF icon pl004_davis_joint_plenary_2011_o.pdf More Documents & Publications Vehicle Technologies Office: 2014 DEER Overview of the U.S. DOE Vehicle Technologies Program U.S. Department of Energy Vehicle Technologies Program Overview

  16. U.S.-Brazil Strategic Energy Dialogue Joint Report | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dialogue Joint Report U.S.-Brazil Strategic Energy Dialogue Joint Report PDF icon First Joint Report to Presidents on U.S.-Brazil Strategic Energy Dialogue.pdf More Documents &...

  17. Scanned_Joint_Declaration_(English).pdf | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    English).pdf ScannedJointDeclaration(English).pdf PDF icon ScannedJointDeclaration(English).pdf More Documents & Publications Joint Statement by Energy Ministers of G8, The ...

  18. U.S.-Japan Joint Statement | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -Japan Joint Statement U.S.-Japan Joint Statement U.S.-Japan Joint Statement prepared as part of the International Partnership for a Hydrogen Economy PDF icon usjapanstatementre...

  19. Sealed joint structure for electrochemical device

    DOE Patents [OSTI]

    Tucker, Michael C; Jacobson, Craig P; De Jonghe, Lutgard C; Visco, Steven J

    2013-05-21

    Several members make up a joint in a high-temperature electrochemical device, wherein the various members perform different functions. The joint is useful for joining multiple cells (generally tubular modules) of an electrochemical device to produce a multi-cell segment-in-series stack for a solid oxide fuel cell, for instance. The joint includes sections that bond the joining members to each other; one or more seal sections that provide gas-tightness, and sections providing electrical connection and/or electrical insulation between the various joining members. A suitable joint configuration for an electrochemical device has a metal joint housing, a first porous electrode, a second porous electrode, separated from the first porous electrode by a solid electrolyte, and an insulating member disposed between the metal joint housing and the electrolyte and second electrode. One or more brazes structurally and electrically connects the first electrode to the metal joint housing and forms a gas tight seal between the first electrode and the second electrode.

  20. Inspection of Fusion Joints in Plastic Pipe

    SciTech Connect (OSTI)

    Connie Reichert

    2005-09-01

    The standard method of joining plastic pipe in the field is the butt fusion process. As in any pipeline application, joint quality greatly affects overall operational safety of the system. Currently no simple, reliable, cost-effective method exists for assessing the quality of fusion joints in the field. Visual examination and pressure testing are current nondestructive approaches, which do not provide any assurance about the long-term pipeline performance. This project developed, demonstrated, and validated an in-situ nondestructive inspection method for butt fusion joints in gas distribution plastic pipelines. The inspection system includes a laser-based image-recognition system that automatically generates and interprets digital images of pipe joints and assigns them a pass/fail rating, which eliminates operator bias in evaluating joint quality. An EWI-patented process, the Weld Zone Inspection Method (WZIM) was developed in which local heat is applied to the joint region to relax the residual stresses formed by the original joining operation, which reveals the surface condition of the joint. In cases where the joint is not formed under optimal conditions, and the intermolecular forces between contacting surfaces are not strong enough, the relaxation of macromolecules in the surface layer causes the material to pull back, revealing a fusion line. If the joint is sound, the bond line image does not develop. To establish initial feasibility of the approach, welds were performed under standard and nonstandard conditions. These welds were subjected to the WZIM and two destructive forms of testing: short-term tensile testing and long-term creep rupture testing. There appears to be a direct correlation between the WZIM and the destructive testing results. Although WZIM appears to be more sensitive than destructive testing can verify, the approach appears valid.

  1. United States and Czech Republic Establish a Joint Civil Nuclear...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Czech Republic Establish a Joint Civil Nuclear Cooperation Center in Prague United States and Czech Republic Establish a Joint Civil Nuclear Cooperation Center in Prague June 12, ...

  2. New Report Describes Joint Opportunities for Natural Gas and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Report Describes Joint Opportunities for Natural Gas and Hydrogen Fuel Cell Vehicle Markets New Report Describes Joint Opportunities for Natural Gas and Hydrogen Fuel Cell Vehicle...

  3. Ryazan Metal Ceramics Instrumentation Plant Joint Stock Co RMCIP...

    Open Energy Info (EERE)

    Ryazan Metal Ceramics Instrumentation Plant Joint Stock Co RMCIP JSC Jump to: navigation, search Name: Ryazan Metal Ceramics Instrumentation Plant Joint Stock Co (RMCIP JSC) Place:...

  4. Tianjin Lishen Battery Joint stock Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    Lishen Battery Joint stock Co Ltd Jump to: navigation, search Name: Tianjin Lishen Battery Joint-stock Co Ltd Place: Tianjin, Tianjin Municipality, China Zip: 300384 Product:...

  5. Joint inversion of electrical and seismic data for Fracture char...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint inversion of electrical and seismic data for Fracture char. and Imaging of Fluid Flow in Geothermal Systems Joint inversion of electrical and seismic data for Fracture char. ...

  6. Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attendees List Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting Attendees List Attendee list from the Joint Meeting on Hydrogen Delivery Modeling and Analysis, May...

  7. Joint Venture Established Between Russian Weapons Plant And the...

    National Nuclear Security Administration (NNSA)

    Jobs Apply for Our Jobs Our Jobs Working at NNSA Blog Home Library Press Releases Joint Venture Established Between Russian Weapons Plant ... Joint Venture Established...

  8. International Power Girasolar joint company | Open Energy Information

    Open Energy Info (EERE)

    search Name: International Power Girasolar joint company Sector: Solar Product: Joint venture announced between US IPWG and Netherlands-headquartered Girasolar, to...

  9. Comparison of Joint Modeling Approaches Including Eulerian Sliding...

    Office of Scientific and Technical Information (OSTI)

    In all cases the sliding interfaces are tracked explicitly without homogenization or blending the joint and block response into an average response. In general, rock joints will ...

  10. Joint Global Change Research Institute | Open Energy Information

    Open Energy Info (EERE)

    solutions. Joint Institute staff bring decades of experience and expertise to bear in science, technology, economics, and policy. "The Joint Global Change Research Institute...

  11. DOE Joint Solid-State Lighting Roundtables on Science Challenges...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Joint Solid-State Lighting Roundtables on Science Challenges DOE Joint Solid-State Lighting Roundtables on Science Challenges PDF icon 2014BES-EEREroundtables...

  12. Joint Statement of Intent Concerning the Arak Heavy Water Reactor...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Intent Concerning the Arak Heavy Water Reactor Research Reactor Modernization Project under the Joint Comprehensive Plan of Action Joint Statement of Intent Concerning the Arak ...

  13. National Report Joint Convention on the Safety of Spent Fuel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management National Report Joint Convention on the Safety of Spent Fuel Management...

  14. United States -Japan Joint Nuclear Energy Action Plan | Department...

    Office of Environmental Management (EM)

    -Japan Joint Nuclear Energy Action Plan United States -Japan Joint Nuclear Energy Action Plan President Bush of the United States and Prime Minister Koizumi of Japan have both...

  15. Joint Actinide Shock Physics Experimental Research - JASPER

    ScienceCinema (OSTI)

    None

    2015-01-09

    Commonly known as JASPER the Joint Actinide Shock Physics Experimental Research facility is a two stage light gas gun used to study the behavior of plutonium and other materials under high pressures, temperatures, and strain rates.

  16. Joint Actinide Shock Physics Experimental Research - JASPER

    SciTech Connect (OSTI)

    2014-10-31

    Commonly known as JASPER the Joint Actinide Shock Physics Experimental Research facility is a two stage light gas gun used to study the behavior of plutonium and other materials under high pressures, temperatures, and strain rates.

  17. Joint Genome Institute's Automation Approach and History

    SciTech Connect (OSTI)

    Roberts, Simon

    2006-07-05

    Department of Energy/Joint Genome Institute (DOE/JGI) collaborates with DOE national laboratories and community users, to advance genome science in support of the DOE missions of clean bio-energy, carbon cycling, and bioremediation.

  18. Safety Monitor Joint Working Group (JWG) Tour

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 th Meeting of the Joint Working Group of the U.S.-Japan Coordinating Committee of Fusion Energy on Safety in Inter-Institutional Collaborations (U.S.-Japan Safety Monitoring...

  19. Joint USDA/DOE meeting

    SciTech Connect (OSTI)

    Not Available

    1994-07-01

    This documents contains the details from the USDA/USDOE meeting on April 11--12, 1994. Topics discussed include: genetic research, environmental research, renewable energy sources, food supply, improved fertilizers, new pesticides, research programs combining the efforts of the two agencies to develop new products for use in the agriculture industry, environmentally safe products, getting more with less money, and various other subjects dealing with how cooperation among these agencies can improve the agriculture industry.

  20. Joint BioEnergy Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear Energy Nuclear

  1. DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Computations | Department of Energy 0 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. PDF icon vss006_salari_2010_o.pdf More Documents & Publications DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments and Computations

  2. CHARACTERIZATION OF DAMPING IN BOLTED LAP JOINTS

    SciTech Connect (OSTI)

    C. MALONEY; D. PEAIRS; ET AL

    2000-08-01

    The dynamic response of a jointed beam was measured in laboratory experiments. The data were analyzed and the system was mathematically modeled to establish plausible representations of joint damping behavior. Damping is examined in an approximate, local linear framework using log decrement and half power bandwidth approaches. in addition, damping is modeled in a nonlinear framework using a hybrid surface irregularities model that employs a bristles-construct. Experimental and analytical results are presented.

  3. DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Computations | Department of Energy 2 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting PDF icon vss006_salari_2012_o.pdf More Documents & Publications DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments and Computations Vehicle Technologies Office Merit Review 2014: DOE's Effort to Improve Heavy Vehicle Fuel Efficiency through Improved Aerodynamics Vehicle Technologies Office Merit Review 2015:

  4. DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Computations | Department of Energy 09 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. PDF icon vss_14_salari.pdf More Documents & Publications DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments and Computations Vehicle Technologies Office Merit Review 2014: DOE's Effort to Improve Heavy Vehicle Fuel Efficiency through Improved Aerodynamics

  5. CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy 2 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting PDF icon ace022_daw_2012_o.pdf More Documents & Publications CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR Emissions Control for Lean Gasoline Engines NH3 generation over commercial Three-Way Catalysts and Lean-NOx Traps

  6. DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments

    Office of Environmental Management (EM)

    and Computations | Department of Energy 1 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation PDF icon vss006_salari_2011_o.pdf More Documents & Publications Vehicle Technologies Office Merit Review 2014: DOE's Effort to Improve Heavy Vehicle Fuel Efficiency through Improved Aerodynamics DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments and Computations DOEs Effort to Reduce Truck Aerodynamic Drag through

  7. DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments

    Office of Environmental Management (EM)

    and Computations | Department of Energy 3 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting PDF icon vss006_salari_2013_o.pdf More Documents & Publications Vehicle Technologies Office Merit Review 2014: DOE's Effort to Improve Heavy Vehicle Fuel Efficiency through Improved Aerodynamics DOEs Effort to Reduce Truck Aerodynamic Drag through Joint Experiments and Computations Vehicle Technologies Office Merit Review 2015:

  8. 2012 U.S. Department of Energy: Joint Genome Institute: Progress Report

    SciTech Connect (OSTI)

    Gilbert, David

    2013-01-01

    The mission of the U.S. Department of Energy Joint Genome Institute (DOE JGI) is to serve the diverse scientific community as a user facility, enabling the application of large-scale genomics and analysis of plants, microbes, and communities of microbes to address the DOE mission goals in bioenergy and the environment. The DOE JGI's sequencing efforts fall under the Eukaryote Super Program, which includes the Plant and Fungal Genomics Programs; and the Prokaryote Super Program, which includes the Microbial Genomics and Metagenomics Programs. In 2012, several projects made news for their contributions to energy and environment research.

  9. 2010_Nuclear_Security_Joint_Statement.pdf | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    _Nuclear_Security_Joint_Statement.pdf 2010_Nuclear_Security_Joint_Statement.pdf PDF icon 2010_Nuclear_Security_Joint_Statement.pdf More Documents & Publications United States and France Sign Joint Statement on Civil Liability for Nuclear Damage US-Japan_NuclearEnergyActionPlan.pdf Before the Senate Armed Services Committee

  10. Residual Stress of Bimetallic Joints and Characterization

    Broader source: Energy.gov [DOE]

    2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  11. Handbook on dynamics of jointed structures.

    SciTech Connect (OSTI)

    Ames, Nicoli M.; Lauffer, James P.; Jew, Michael D.; Segalman, Daniel Joseph; Gregory, Danny Lynn; Starr, Michael James; Resor, Brian Ray

    2009-07-01

    The problem of understanding and modeling the complicated physics underlying the action and response of the interfaces in typical structures under dynamic loading conditions has occupied researchers for many decades. This handbook presents an integrated approach to the goal of dynamic modeling of typical jointed structures, beginning with a mathematical assessment of experimental or simulation data, development of constitutive models to account for load histories to deformation, establishment of kinematic models coupling to the continuum models, and application of finite element analysis leading to dynamic structural simulation. In addition, formulations are discussed to mitigate the very short simulation time steps that appear to be required in numerical simulation for problems such as this. This handbook satisfies the commitment to DOE that Sandia will develop the technical content and write a Joints Handbook. The content will include: (1) Methods for characterizing the nonlinear stiffness and energy dissipation for typical joints used in mechanical systems and components. (2) The methodology will include practical guidance on experiments, and reduced order models that can be used to characterize joint behavior. (3) Examples for typical bolted and screw joints will be provided.

  12. DOE Joint Genome Institute 2008 Progress Report

    SciTech Connect (OSTI)

    Gilbert, David

    2009-03-12

    While initially a virtual institute, the driving force behind the creation of the DOE Joint Genome Institute in Walnut Creek, California in the Fall of 1999 was the Department of Energy's commitment to sequencing the human genome. With the publication in 2004 of a trio of manuscripts describing the finished 'DOE Human Chromosomes', the Institute successfully completed its human genome mission. In the time between the creation of the Department of Energy Joint Genome Institute (DOE JGI) and completion of the Human Genome Project, sequencing and its role in biology spread to fields extending far beyond what could be imagined when the Human Genome Project first began. Accordingly, the targets of the DOE JGI's sequencing activities changed, moving from a single human genome to the genomes of large numbers of microbes, plants, and other organisms, and the community of users of DOE JGI data similarly expanded and diversified. Transitioning into operating as a user facility, the DOE JGI modeled itself after other DOE user facilities, such as synchrotron light sources and supercomputer facilities, empowering the science of large numbers of investigators working in areas of relevance to energy and the environment. The JGI's approach to being a user facility is based on the concept that by focusing state-of-the-art sequencing and analysis capabilities on the best peer-reviewed ideas drawn from a broad community of scientists, the DOE JGI will effectively encourage creative approaches to DOE mission areas and produce important science. This clearly has occurred, only partially reflected in the fact that the DOE JGI has played a major role in more than 45 papers published in just the past three years alone in Nature and Science. The involvement of a large and engaged community of users working on important problems has helped maximize the impact of JGI science. A seismic technological change is presently underway at the JGI. The Sanger capillary-based sequencing process that dominated how sequencing was done in the last decade is being replaced by a variety of new processes and sequencing instruments. The JGI, with an increasing number of next-generation sequencers, whose throughput is 100- to 1,000-fold greater than the Sanger capillary-based sequencers, is increasingly focused in new directions on projects of scale and complexity not previously attempted. These new directions for the JGI come, in part, from the 2008 National Research Council report on the goals of the National Plant Genome Initiative as well as the 2007 National Research Council report on the New Science of Metagenomics. Both reports outline a crucial need for systematic large-scale surveys of the plant and microbial components of the biosphere as well as an increasing need for large-scale analysis capabilities to meet the challenge of converting sequence data into knowledge. The JGI is extensively discussed in both reports as vital to progress in these fields of major national interest. JGI's future plan for plants and microbes includes a systematic approach for investigation of these organisms at a scale requiring the special capabilities of the JGI to generate, manage, and analyze the datasets. JGI will generate and provide not only community access to these plant and microbial datasets, but also the tools for analyzing them. These activities will produce essential knowledge that will be needed if we are to be able to respond to the world's energy and environmental challenges. As the JGI Plant and Microbial programs advance, the JGI as a user facility is also evolving. The Institute has been highly successful in bending its technical and analytical skills to help users solve large complex problems of major importance, and that effort will continue unabated. The JGI will increasingly move from a central focus on 'one-off' user projects coming from small user communities to much larger scale projects driven by systematic and problem-focused approaches to selection of sequencing targets. Entire communities of scientists working in a particular field, such as feedstock improvement or biomass degradation, will be users of this information. Despite this new emphasis, an investigator-initiated user program will remain. This program in the future will replace small projects that increasingly can be accomplished without the involvement of JGI, with imaginative large-scale 'Grand Challenge' projects of foundational relevance to energy and the environment that require a new scale of sequencing and analysis capabilities. Close interactions with the DOE Bioenergy Research Centers, and with other DOE institutions that may follow, will also play a major role in shaping aspects of how the JGI operates as a user facility. Based on increased availability of high-throughput sequencing, the JGI will increasingly provide to users, in addition to DNA sequencing, an array of both pre- and post-sequencing value-added capabilities to accelerate their science.

  13. Qualification of the Joints for the ITER Central Solenoid

    SciTech Connect (OSTI)

    Martovetsky, N; Berryhill, A; Kenney, S

    2011-09-01

    The ITER Central Solenoid has 36 interpancake joints, 12 bus joints, and 12 feeder joints in the magnet. The joints are required to have resistance below 4 nOhm at 45 kA at 4.5 K. The US ITER Project Office developed two different types of interpancake joints with some variations in details in order to find a better design, qualify the joints, and establish a fabrication process. We built and tested four samples of the sintered joints and two samples with butt-bonded joints (a total of eight joints). Both designs met the specifications. Results of the joint development, test results, and selection of the baseline design are presented and discussed in the paper. The ITER Central Solenoid (CS) consists of six modules. Each module is composed of six wound hexapancakes and one quadrapancake. The multipancakes are connected electrically and hydraulically by in-line interpancake joints. The joints are located at the outside diameter (OD) of the module. Cable in conduit conductor (CICC) high-current joints are critical elements in the CICC magnets. In addition to low resistivity, the CS joints must fit a space envelope equivalent to the regular conductor cross section and must have low hydraulic impedance and enough structural strength to withstand the hoop and compressive forces during operation, including cycling. This paper is the continuation of the work reported on the intermodule joints.

  14. EERE Day at MIT Inspires Next Generation of Clean Energy Leaders

    Broader source: Energy.gov [DOE]

    It’s easy to break down our research and development investments into the programs we support, the partnerships we’ve built, and the cutting edge clean energy technologies our partners deploy. But...

  15. ESnet, CENIC ESnet Announce Joint Cybersecurity Initiative

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ESnet, CENIC Announce Joint Cybersecurity Initiative News & Publications ESnet News Media & Press Publications and Presentations Galleries ESnet Awards and Honors Contact Us Media Jon Bashor, jbashor@lbl.gov, +1 510 486 5849 or Media@es.net Technical Assistance: 1 800-33-ESnet (Inside the US) 1 800-333-7638 (Inside the US) 1 510-486-7600 (Globally) 1 510-486-7607 (Globally) Report Network Problems: trouble@es.net Provide Web Site Feedback: info@es.net ESnet, CENIC Announce Joint

  16. Electric thermal storage demonstration program

    SciTech Connect (OSTI)

    Not Available

    1992-02-01

    In early 1989, MMWEC, a joint action agency comprised of 30 municipal light departments in Massachusetts and one affiliate in Rhode Island, responded to a Department of Energy request to proposal for the Least Cost Utility Planning program. The MMWEC submission was for the development of a program, focused on small rural electric utilities, to promote the use of electric thermal storage heating systems in residential applications. In this progress report, cost savings at Bolyston light department is discussed. (JL)

  17. Electric thermal storage demonstration program

    SciTech Connect (OSTI)

    Not Available

    1992-01-01

    In early 1989, MMWEC, a joint action agency comprised of 30 municipal light departments in Massachusetts and one affiliate in Rhode Island, responded to a Department of Energy request to proposal for the Least Cost Utility Planning program. The MMWEC submission was for the development of a program, focused on small rural electric utilities, to promote the use of electric thermal storage heating systems in residential applications. In this progress report, cost savings at Bolyston light department is discussed. (JL)

  18. Environmental Programs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Los Alamos County Fire Department provides wildfire suppression support. The New Mexico Joint Powers Agreement, between the state Forestry Division, DOE, the Department of...

  19. Introduction to Metagenomics at DOE JGI: Program Overview and Program Informatics (Metagenomics Informatics Challenges Workshop: 10K Genomes at a Time)

    ScienceCinema (OSTI)

    Tringe, Susannah [DOE JGI

    2013-01-22

    Susannah Tringe of the DOE Joint Genome Institute talks about the Program Overview and Program Informatics at the Metagenomics Informatics Challenges Workshop held at the DOE JGI on October 12-13, 2011

  20. SEALING LARGE-DIAMETER CAST-IRON PIPE JOINTS UNDER LIVE CONDITIONS

    SciTech Connect (OSTI)

    Kiran M. Kothari; Gerard T. Pittard

    2005-07-01

    Utilities in the U.S. operate over 75,000 km (47,000 miles) of old cast-iron pipes for gas distribution. Bell-and-spigot joints that connect pipe sections together tend to leak as these pipes age. Current repair practices are costly and highly disruptive. The objective of this program is to design, test and commercialize a robotic system capable of sealing multiple castiron bell and spigot joints from a single pipe entry point. The proposed system will perform repairs with the pipe in service by traveling through the pipe, cleaning each joint surface, and installing a stainless-steel sleeve lined with an epoxy-impregnated felt across the joint. This approach will save considerable time and labor, minimize excavation, avoid traffic disruption, and eliminate any requirement to interrupt service to customers (which would result in enormous expense to utilities). Technical challenges include: (1) repair sleeves must compensate for diametric variation and eccentricity of old cast-iron pipes; (2) the assembly must travel long distances through pipes containing debris; (3) the pipe wall must be effectively cleaned in the immediate area of the joint to assure good bonding of the sleeve; and (4) an innovative bolt-on entry fitting is required to conduct safe repair operations on live mains.

  1. Wide temperature range seal for demountable joints

    DOE Patents [OSTI]

    Sixsmith, H.; Valenzuela, J.A.; Nutt, W.E.

    1991-07-23

    The present invention is directed to a seal for demountable joints operating over a wide temperature range down to liquid helium temperatures. The seal has anti-extrusion guards which prevent extrusion of the soft ductile sealant material, which may be indium or an alloy thereof. 6 figures.

  2. Wide temperature range seal for demountable joints

    DOE Patents [OSTI]

    Sixsmith, Herbert (Norwich, VT); Valenzuela, Javier A. (Grantham, NH); Nutt, William E. (Enfield, NH)

    1991-07-23

    The present invention is directed to a seal for demountable joints operating over a wide temperature range down to liquid helium temperatures. The seal has anti-extrusion guards which prevent extrusion of the soft ductile sealant material, which may be indium or an alloy thereof.

  3. Joint with application in electrochemical devices

    DOE Patents [OSTI]

    Weil, K Scott [Richland, WA; Hardy, John S [Richland, WA

    2010-09-14

    A joint for use in electrochemical devices, such as solid oxide fuel cells (SOFCs), oxygen separators, and hydrogen separators, that will maintain a hermetic seal at operating temperatures of greater than 600.degree. C., despite repeated thermal cycling excess of 600.degree. C. in a hostile operating environment where one side of the joint is continuously exposed to an oxidizing atmosphere and the other side is continuously exposed to a wet reducing gas. The joint is formed of a metal part, a ceramic part, and a flexible gasket. The flexible gasket is metal, but is thinner and more flexible than the metal part. As the joint is heated and cooled, the flexible gasket is configured to flex in response to changes in the relative size of the metal part and the ceramic part brought about by differences in the coefficient of thermal expansion of the metal part and the ceramic part, such that substantially all of the tension created by the differences in the expansion and contraction of the ceramic and metal parts is absorbed and dissipated by flexing the flexible gasket.

  4. United States and France Sign Joint Statement on Civil Liability...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    France Sign Joint Statement on Civil Liability for Nuclear Damage United States and France Sign Joint Statement on Civil Liability for Nuclear Damage August 29, 2013 - 1:36pm ...

  5. Introduction to Using NERSC for the Joint Genome Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NERSC Introduction to Using NERSC for the Joint Genome Institute May 2, 2011 jgi logo sm NERSC Training Event 1:00-5:00 p.m. PDT May 2, 2011 Joint Genome Institute, 2800 Mitchell...

  6. Tianjin B M Science Technology Joint Stock Ltd | Open Energy...

    Open Energy Info (EERE)

    Science Technology Joint Stock Ltd Jump to: navigation, search Name: Tianjin B&M Science & Technology Joint Stock, Ltd Place: China Product: China-based maker of cathode material...

  7. Fourth National Report for the Joint Convention on the Safety...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management Fourth National Report for the Joint Convention on the Safety of Spent...

  8. Second National Report for the Joint Convention on the Safety...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management Second National Report for the Joint Convention on the Safety of Spent...

  9. Third National Report for the Joint Convention on the Safety...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management Third National Report for the Joint Convention on the Safety of Spent...

  10. Fifth National Report for the Joint Convention on the Safety...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the Joint Convention on the Safety of Spent Fuel Management and the Safety of Radioactive Waste Management Fifth National Report for the Joint Convention on the Safety of Spent...

  11. Program Evaluation: Program Logic

    Broader source: Energy.gov [DOE]

    Logic modeling is a thought process program evaluators have found to be useful for at least forty years and has become increasingly popular with program managers during the last decade. A logic model presents a plausible and sensible model of how the program will work under certain environmental conditions to solve identified problems. The logic model can be the basis for a convincing story of the program's expected performance – telling stakeholders and others the problem the program focuses on and how it is uniquely qualified to address it. The elements of the logic model are resources, activities, outputs, short, intermediate and longer-term outcomes. Some add the customers reached, as well as the relevant external contextual influences, present before a program begins or appearing as the program is implemented.

  12. Microbial Genomics Data from the DOE Joint Genome Institute (JGI)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    As of March 2008, The Joint Genome Institute has released 296 Prokaryotic microbial sites, with 216 in finished status.

  13. Seismic Capacity of Threaded, Brazed, and Grooved Pipe Joints

    Office of Environmental Management (EM)

    SEISMIC CAPACITY OF THREADED, BRAZED AND GROOVED PIPE JOINTS Brent Gutierrez, PhD, PE George Antaki, PE, F.ASME DOE NPH Conference October 25-26, 2011 Motivation * Understand the behavior and failure mode of common joints under extreme lateral loads * Static and shake table tests conducted of pressurized - Threaded, - Brazed, - Mechanical joints Static Testing o Pressurized spool to 150 psi o Steady downward force applied while recording deflections o Grooved clamped mech. joints * 16 tests

  14. Comparison of Joint Modeling Approaches Including Eulerian Sliding

    Office of Scientific and Technical Information (OSTI)

    Interfaces (Technical Report) | SciTech Connect Comparison of Joint Modeling Approaches Including Eulerian Sliding Interfaces Citation Details In-Document Search Title: Comparison of Joint Modeling Approaches Including Eulerian Sliding Interfaces Accurate representation of discontinuities such as joints and faults is a key ingredient for high fidelity modeling of shock propagation in geologic media. The following study was done to improve treatment of discontinuities (joints) in the Eulerian

  15. Equivalent Continuum Modeling for Shock Wave Propagation in Jointed Media

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Equivalent Continuum Modeling for Shock Wave Propagation in Jointed Media Citation Details In-Document Search Title: Equivalent Continuum Modeling for Shock Wave Propagation in Jointed Media This study presents discrete and continuum simulations of shock wave propagating through jointed media. The simulations were performed using the Lagrangian hydrocode GEODYN-L with joints treated explicitly using an advanced contact algorithm. They studied both

  16. Comments of the Joint Center for Political and Economic Studies |

    Office of Environmental Management (EM)

    Department of Energy Joint Center for Political and Economic Studies Comments of the Joint Center for Political and Economic Studies The Media and Technology Institute and the Climate Change Initiative at the Joint Center for Political and Economic Studies ("Joint Center")1 respectfully submit these comments in response to the United States Department of Energy's ("DoE") Request for Information regarding its implementation of the Smart Grid provisions of Federal

  17. EISA 2007: Focus on Renewable Fuels Standard Program

    Broader source: Energy.gov [DOE]

    At the November 6, 2008 joint Web conference of DOE's Biomass and Clean Cities programs, Paul Argyropoulos (U.S. Environmental Protection Agency, Office of Transportation and Air Quality) explained the EISA 2007, Renewable Fuel Standards.

  18. Compact Ignition Tokamak Program: status of FEDC studies

    SciTech Connect (OSTI)

    Flanagan, C.A.

    1985-01-01

    Viewgraphs on the Compact Ignition Tokamak Program comprise the report. The technical areas discussed are the mechanical configuration status, magnet analysis, stress analysis, cooling between burns, TF coil joint, and facility/device layout options. (WRF)

  19. Joint Working Group for Fusion Safety | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Business Operations Careers/ Human Resources Directory Environment, Safety & Health Environmental Management System Joint Working Group for Fusion Safety Furth Plasma Physics Library Lab Leadership Organization Chart Technology Transfer Contact Us Business Operations Careers/ Human Resources Directory Environment, Safety & Health Environmental Management System Joint Working Group for Fusion Safety Furth Plasma Physics Library Lab Leadership Organization Chart Technology Transfer Joint

  20. U.S.-European Union Joint Statement | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -European Union Joint Statement U.S.-European Union Joint Statement U.S.-European Union Joint Statement prepared as part of the International Partnership for a Hydrogen Economy PDF icon us_eu_hydrogen_summit_statement.pdf More Documents & Publications Microsoft Word - Document1 International Partnerships for the Hydrogen Economy Fact Sheet International Partnerships for the Hydrogen Economy Fact Sheet

  1. LDRD joint computational/experimental project

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LDRD joint computational/experimental project - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste

  2. Joint NSRC Workshop 2015: Big, Deep, and Smart Data Analytics in Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Imaging NSRC Workshop 2015 Joint NSRC Workshop 2015: Big, Deep, and Smart Data Analytics in Materials Imaging Home Announcement Meeting REGISTRATION Call for Abstracts Abstract Submission Venue & Access Important Dates Travel & Lodging Invited Speakers Agenda Program Committee Contact Us CNMS Home Welcome NSRC Workshop: Big, Deep, and Smart Data Analytics in Materials Imaging Contact: Conference Contact, Amanda Zetans, 865-241-1182 [ Website | ORNL | DOE | Privacy | Accessibility ]

  3. CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy 0 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. PDF icon ace022_daw_2010_o.pdf More Documents & Publications CLEERS Coordination & Development of Catalyst Process Kinetic Data CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR Functionality of Commercial NOx Storage-Reduction Catalysts and the Development of a Representative Model

  4. Vice Chairman of the Joint Chiefs of Staff Visits Los Alamos National

    National Nuclear Security Administration (NNSA)

    Laboratory | National Nuclear Security Administration Vice Chairman of the Joint Chiefs of Staff Visits Los Alamos National Laboratory | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios

  5. Final report. U.S. Department of Energy University Reactor Sharing Program

    SciTech Connect (OSTI)

    Bernard, John A.

    2003-01-21

    Activities supported at the MIT Nuclear Reactor Laboratory under the U.S. DOE University Reactor Sharing Program are reported for Grant DE FG02-95NE38121 (September 16, 1995 through May 31, 2002). These activities fell under four subcategories: support for research at thesis and post-doctoral levels, support for college-level laboratory exercises, support for reactor tours/lectures on nuclear energy, and support for science fair participants.

  6. Scientific program and abstracts

    SciTech Connect (OSTI)

    Gerich, C.

    1983-01-01

    The Fifth International Conference on High-Power Particle Beams is organized jointly by the Lawrence Livermore National Laboratory and Physics International Company. As in the previous conferences in this series, the program includes the following topics: high-power, electron- and ion-beam acceleration and transport; diode physics; high-power particle beam interaction with plasmas and dense targets; particle beam fusion (inertial confinement); collective ion acceleration; particle beam heating of magnetically confined plasmas; and generation of microwave/free-electron lasers.

  7. Bo Zhen | Solid State Solar Thermal Energy Conversion

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Bo Zhen Researchers Bo Zhen Postdoctoral Researcher, MIT Phone: (617) 258-6286 Email: bozhen@MIT.EDU Web: Bo Zhen Website Bio: Bo Zhen received a B.S. in 2008 from Tsinghua University (Academic talent program, Mathematics & Physics), and a PhD in 2014 from MIT Physics. Since then, he has been working as a joint postdoctoral associate with Marin Soljačić at MIT and Mordechai Segev at Technion, Israel. His major research interest is in designing and demonstrating novel nanophotonic devices

  8. Joint Center for Energy Storage Research

    SciTech Connect (OSTI)

    Eric Isaacs

    2012-11-30

    The Joint Center for Energy Storage Research (JCESR) is a major public-private research partnership that integrates U.S. Department of Energy national laboratories, major research universities and leading industrial companies to overcome critical scientific challenges and technical barriers, leading to the creation of breakthrough energy storage technologies. JCESR, centered at Argonne National Laboratory, outside of Chicago, consolidates decades of basic research experience that forms the foundation of innovative advanced battery technologies. The partnership has access to some of the world's leading battery researchers as well as scientific research facilities that are needed to develop energy storage materials that will revolutionize the way the United States and the world use energy.

  9. Drill Program Ensures Emergency Preparedness

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Joint Information Center practice responding to a mock event during a drill held on November 12. WIPP UPDATE: November 13, 2014 Drill Program Ensures Emergency Preparedness As part of its Corrective Action Plans in response to the Accident Investigation Board reports for the February fire and radiological events, the WIPP Emergency Response Organization (ERO) has undergone extensive change over the past eight months. In addition to adding new personnel, there have been major revisions to

  10. Joint statement of the European Commission's Joint Research Centre and the

    National Nuclear Security Administration (NNSA)

    United States Department of Energy's National Nuclear Security Administration regarding the reduction of excess nuclear material | National Nuclear Security Administration statement of the European Commission's Joint Research Centre and the United States Department of Energy's National Nuclear Security Administration regarding the reduction of excess nuclear material | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile

  11. FY15 LLNL OMEGA Experimental Programs

    SciTech Connect (OSTI)

    Heeter, R. F.; Baker, K. L.; Barrios, M. A.; Beckwith, M. A.; Casey, D. T.; Celliers, P. M.; Chen, H.; Coppari, F.; Fournier, K. B.; Fratanduono, D. E.; Frenje, J.; Huntington, C. M.; Kraus, R. G.; Lazicki, A. E.; Martinez, D. A.; McNaney, J. M.; Millot, M. A.; Pak, A. E.; Park, H. S.; Ping, Y.; Pollock, B. B.; Smith, R. F.; Wehrenberg, C. E.; Widmann, K.; Collins, G. W.; Landen, O. L.; Wan, A.; Hsing, W.

    2015-12-04

    In FY15, LLNLs High-Energy-Density Physics (HED) and Indirect Drive Inertial Confinement Fusion (ICF-ID) programs conducted several campaigns on the OMEGA laser system and on the EP laser system, as well as campaigns that used the OMEGA and EP beams jointly. Overall these LLNL programs led 468 target shots in FY15, with 315 shots using just the OMEGA laser system, 145 shots using just the EP laser system, and 8 Joint shots using Omega and EP together. Approximately 25% of the total number of shots (56 OMEGA shots and 67 EP shots, including the 8 Joint shots) supported the Indirect Drive Inertial Confinement Fusion Campaign (ICF-ID). The remaining 75% (267 OMEGA shots and 86 EP shots) were dedicated to experiments for High-Energy-Density Physics (HED). Highlights of the various HED and ICF campaigns are summarized in the following reports.

  12. Weatherization Program

    Broader source: Energy.gov [DOE]

    Residences participating in the Home Energy Rebate or New Home Rebate Program may not also participate in the Weatherization Program.

  13. Program Analysis

    Broader source: Energy.gov [DOE]

    2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Vehicle Technologies Plenary

  14. Joint Fuel Cell Technologies and Advanced Manufacturing Webinar |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Fuel Cell Technologies and Advanced Manufacturing Webinar Joint Fuel Cell Technologies and Advanced Manufacturing Webinar Download the presentation slides from the "Joint Fuel Cell Technologies Office and Advanced Manufacturing Office Webinar" held November 20, 2012. PDF icon Joint Fuel Cell Technologies Office and Advanced Manufacturing Office Webinar Slides More Documents & Publications Hydrogen and Fuel Cell Technologies FY 2014 Budget Request Rollout to

  15. Science On Tap - From Trinity to Artificial Joints

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Science On Tap - From Trinity to Artificial Joints Science On Tap - From Trinity to Artificial Joints WHEN: Jul 16, 2015 5:30 PM - 7:00 PM WHERE: UnQuarked Wine Room 145 Central Park Square, Los Alamos, New Mexico 87544, USA SPEAKER: Nathaniel Morgan, Los Alamos National Laboratory CONTACT: Jessica Privette 505 667-0375 CATEGORY: Bradbury INTERNAL: Calendar Login Science on Tap series Event Description From Trinity to artificial joints: How computational mathematics has transformed our world.

  16. Development of the bus joint for the ITER Central Solenoid

    SciTech Connect (OSTI)

    Martovetsky, Nicolai N; Irick, David Kim; Kenney, Steven J

    2013-01-01

    The terminations of the Central Solenoid (CS) modules are connected to the bus extensions by joints located outside the CS in the gap between the CS and Torodial Field (TF) assemblies. These joints have very strict space limitations. Low resistance is a common requirement for all ITER joints. In addition, the CS bus joints will experience and must be designed to withstand significant variation in the magnetic field of several tenths of a Tesla per second during initiation of plasma. The joint resistance is specified to be less than 4 nOhm. The joints also have to be soldered in the field and designed with the possibility to be installed and dismantled in order to allow cold testing in the cold test facility. We have developed coaxial joints that meet these requirements and have demonstrated the feasibility to fabricate and assemble them in the vertical configuration. We introduced a coupling cylinder with superconducting strands soldered to the surface of the cable that can be installed in the ITER assembly hall and at the Cold Test Facility. This cylinder serves as a transition area between the CS module and the bus extension. We made two racetrack samples and tested four bus joints in our Joint Test Apparatus. Resistance of the bus joints was measured by a decay method and by a microvoltmeter; the value of the current was measured by the Hall probes. This measurement method was verified in the previous tests. The resistance of the joints varied insignificantly from 1.5 to 2 nOhm. One of the challenges associated with a soldered joint is the inability to use corrosive chemicals that are difficult to clean. This paper describes our development work on cable preparation, chrome removal, compaction, soldering, and final assembly and presents the test results.

  17. Secretary Bodman, Director Rumyantsev Issue Joint Statement on Bratislava

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Nuclear Security Initiatives | Department of Energy Bodman, Director Rumyantsev Issue Joint Statement on Bratislava Nuclear Security Initiatives Secretary Bodman, Director Rumyantsev Issue Joint Statement on Bratislava Nuclear Security Initiatives November 9, 2005 - 2:20pm Addthis WASHINGTON, DC - U.S. Secretary of Energy Samuel Bodman and Russian Federal Atomic Energy Agency Director, Aleksandr Rumyantsev today released a joint statement on the status of the Bratislava Nuclear Security

  18. Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting Agenda |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Agenda Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting Agenda Agenda for the Joint Meeting on Hydrogen Delivery Modeling and Analysis, May 8-9, 2007 PDF icon deliv_analysis_agenda.pdf More Documents & Publications Hydrogen Delivery Analysis Models Hydrogen Delivery Analysis Plus Meeting: DTT, STT, HPTT, Other Analysts, Invited Guests Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting Attendees List

  19. Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting Attendees

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    List | Department of Energy Attendees List Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting Attendees List Attendee list from the Joint Meeting on Hydrogen Delivery Modeling and Analysis, May 8-9, 2007 PDF icon deliv_analysis_attendees.pdf More Documents & Publications DOE and FreedomCAR and Fuel Partnership Analysis Workshop Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting Agenda DOE and FreedomCAR and Fuel Partnership Analysis Workshop

  20. OMB and CEQ Joint Memorandum on Environmental Collaboration and Conflict

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Resolution | Department of Energy OMB and CEQ Joint Memorandum on Environmental Collaboration and Conflict Resolution OMB and CEQ Joint Memorandum on Environmental Collaboration and Conflict Resolution This Office of Management and Budget (OMB) and Council on Environmental Quality (CEQ) joint memorandum expands and builds on the November 28, 2005, Environmental Conflict Resolution (ECR) Memorandum, directing departments and agencies to increase the appropriate and effective use of

  1. Electrical Detector for Liquid Lithium Leaks Around Demountable Pipe Joints

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    | Princeton Plasma Physics Lab Electrical Detector for Liquid Lithium Leaks Around Demountable Pipe Joints This system is designed to detect leaks of liquid lithium from around demountable pipe joints. Demountable pipe joints such as vacuum fittings are likely spots for a leak in any system transporting fluids. Since liquid lithium reacts with air, water, concrete and other common materials, it is important to quickly detect a leak. The system will partially contain the leak and is designed

  2. Stochastic Joint Inversion for Integrated Data Interpretation in Geothermal

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Exploration | Department of Energy Stochastic Joint Inversion for Integrated Data Interpretation in Geothermal Exploration Stochastic Joint Inversion for Integrated Data Interpretation in Geothermal Exploration Stochastic Joint Inversion for Integrated Data Interpretation in Geothermal Exploration presentation at the April 2013 peer review meeting held in Denver, Colorado. PDF icon mellors_peer2013.pdf More Documents & Publications track 2: hydrothermal | geothermal 2015 peer review

  3. Joint Trade Mission to China | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Trade Mission to China Joint Trade Mission to China Trade Mission Begins Trade Mission Begins The joint trade mission began in Beijing, and will also make stops in Shanghai and Guangzhou. Read more Green Buildings Green Buildings How American Businesses are leading the way in green building technology in Shanghai and around the world. Read more Top 3 Things Top 3 Things Deputy Secretary Sherwood-Randall spoke at Microsoft's Beijing Campus. These were the top 3 things from her speech. Read

  4. Joint Meeting on Hydrogen Delivery Modeling and Analysis Meeting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Documents & Publications Hydrogen Delivery Analysis Models Hydrogen Delivery Analysis Plus Meeting: DTT, STT, HPTT, Other Analysts, Invited Guests Joint Meeting on Hydrogen...

  5. ORISE: Providing Support to the DOE Joint Information Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Joint Information Center (JIC) ORISE supports DOE's Oak Ridge Office by managing crisis communication facility for drills, exercises and emergencies In the event of an emergency,...

  6. Joint Genome Institute Progress Report 2002-2005

    SciTech Connect (OSTI)

    Gilbert, David

    2005-10-03

    Progress report covering activities at the DOE-Joint Genome Institute in Walnut Creek, California for the period 2002-2005.

  7. El Salvador-Joint Programme on Resource Efficient and Cleaner...

    Open Energy Info (EERE)

    (RECP) in Developing and Transition Countries Jump to: navigation, search Name El Salvador-Joint Programme on Resource Efficient and Cleaner Production (RECP) in Developing and...

  8. SEISMIC CAPACITY OF THREADED, BRAZED AND GROOVED PIPE JOINTS | Department

    Office of Environmental Management (EM)

    of Energy SEISMIC CAPACITY OF THREADED, BRAZED AND GROOVED PIPE JOINTS SEISMIC CAPACITY OF THREADED, BRAZED AND GROOVED PIPE JOINTS Seismic Capacity of Threaded, Brazed and Grooved Pipe Joints Brent Gutierrez, PhD, PE George Antaki, PE, F.ASME DOE NPH Conference October 25-26, 2011 PDF icon Seismic Capacity of Threaded, Brazed and Grooved Pipe Joints More Documents & Publications FY2015 Status Report: CIRFT Testing of High-Burnup Used Nuclear Fuel Rods from Pressurized Water Reactor and

  9. Equivalent Continuum Modeling for Shock Wave Propagation in Jointed...

    Office of Scientific and Technical Information (OSTI)

    Equivalent Continuum Modeling for Shock Wave Propagation in Jointed Media Citation Details In-Document Search Title: Equivalent Continuum Modeling for Shock Wave Propagation in...

  10. Equivalent Continuum Modeling for Shock Wave Propagation in Jointed...

    Office of Scientific and Technical Information (OSTI)

    combined with the properties of the intact rock to develop an equivalent continuum model ... Two appraoches are suggested for modeling the rock mass. In one approach, jointed are ...

  11. Joint transmission system projects to improve system reliability

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    County PUD, 425-783-8444 Joint transmission system projects to improve system reliability First major regional electric grid improvements in decades prepare the area for the...

  12. Science On Tap - From Trinity to Artificial Joints

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    artificial human joints, and biological implants, using MRI scanning software, radiation therapy and even creating cartoons is all done using computational mathematics. The world...

  13. Montana Joint Application for Proposed Work in Montana's Streams...

    Open Energy Info (EERE)

    Notice Form Topic JOINT APPLICATION FOR PROPOSED WORK IN MONTANA'S STREAMS, WETLANDS, FLOODPLAINS, AND OTHER WATER BODIES Organization Montana Department of Natural...

  14. Hydrogen and Fuel Cell Transit Bus Evaluations: Joint Evaluation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Administration Hydrogen and Fuel Cell Transit Bus Evaluations: Joint Evaluation Plan for the U.S. Department of Energy and the Federal Transit Administration This document...

  15. Hydrogen and Fuel Cell Transit Bus Evaluations: Joint Evaluation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Administration; Appendix Hydrogen and Fuel Cell Transit Bus Evaluations: Joint Evaluation Plan for the U.S. Department of Energy and the Federal Transit Administration; Appendix...

  16. Berkeley India Joint Leadership on Energy and Environment | Open...

    Open Energy Info (EERE)

    of pathways and approaches for reducing the emissions of greenhouse gases while pursuing sustainable economic development. The Berkeley India Joint Leadership on Energy and...

  17. Joint Meeting on Hydrogen Delivery Modeling and Analysis, May...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Analysis, May 8-9, 2007, Discussion Session Highlights, Comments, and Action Items Joint Meeting on Hydrogen Delivery Modeling and Analysis, May 8-9, 2007, Discussion...

  18. Comparison of Joint Modeling Approaches Including Eulerian Sliding...

    Office of Scientific and Technical Information (OSTI)

    faults is a key ingredient for high fidelity modeling of shock propagation in geologic media. The following study was done to improve treatment of discontinuities (joints) in the...

  19. Program Evaluation: Program Life Cycle

    Broader source: Energy.gov [DOE]

    In general, different types of evaluation are carried out over different parts of a program's life cycle (e.g., Creating a program, Program is underway, or Closing out or end of program)....

  20. Joint Institute for Nanoscience Annual Report 2003

    SciTech Connect (OSTI)

    Baer, Donald R.; Campbell, Charles

    2004-02-01

    The Joint Institute for Nanoscience (JIN) is a cooperative venture of the University of Washington and Pacific Northwest National Laboratory to encourage and enhance high-impact and high-quality nanoscience and nanotechnology of all types. This first annual report for the JIN summarizes activities beginning in 2001 and ending at the close of fiscal year 2003 and therefore represents somewhat less than two years of activities. Major portions of the JIN resources are dedicated to funding graduate students and postdoctoral research associates to perform research in collaborations jointly directed by Pacific Northwest National Laboratory (PNNL) staff scientists and University of Washington (UW) professors. These fellowships were awarded on the basis of applications that included research proposals. JIN co-sponsors an annual Nanoscale Science and Technology Workshop held in Seattle. In addition to involving PNNL staff in various UW nanoscience courses and seminars, a National Science Foundation grant Development of UW-PNL Collaborative Curriculums in Nano-Science and Technology has allowed the development of three intensive short courses that are taught by UW faculty, PNNL staff, and faculty from other institutions, including Washington State University, the University of Idaho, Stanford University, and the University of Alaska. The initial JIN agreement recognized that expansion of cooperation beyond UW and PNNL would be highly valuable. Starting in early 2003, efforts were initiated to form a regional communication link called the Northwest Nanoscience and Nanotechnology Network (N?). In concept, N? is a tool to encourage communication and help identify regional resources and nanoscience and technology activities.

  1. OE Power Systems Engineering Research & Development Program Partnerships |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Mission » Power Systems Engineering Research and Development » OE Power Systems Engineering Research & Development Program Partnerships OE Power Systems Engineering Research & Development Program Partnerships The OE Power Systems Research and Development Program engages a broad group of stakeholders in program planning, identification of high-priority technology gap areas, and joint participation in research, development, demonstration, and deployment

  2. State Energy Program Success Stories | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    State Energy Program » State Energy Program Success Stories State Energy Program Success Stories RSS Read State Energy Program success stories. August 12, 2015 Paul Thomsen, Director of the Nevada Governor's Office of Energy, announces the new Nevada Electric Highway Joint Initiative in Carson City, Nevada. He was joined at the event by Carson City Mayor Bob Crowell, left, NV Energy CEO Paul Caudill, and Nevada Governor Brian Sandoval. The Initiative received financial support from the Energy

  3. Small Business Programs At-A-Glance

    Energy Savers [EERE]

    z SMALL BUSINESS PROGRAMS AT-A-GLANCE PROGRAM TYPE PROGRAM BENEFITS GENERAL ELIGIBILITY REQUIREMENTS SIZE REQUIREMENTS ADDITIONAL REQUIREMENTS CERTIFICATION PROCESS RECERTIFICATION/MAINTENANCE RELEVANT REGULATIONS 8(a)  Access to sole-source contracts, up to $4M for goods/services and $6.5M for manufacturing.  Access to 8(a) set-asides through "Rule of Two"*.  Participation in 8(a) Mentor-Protégé Program.  Ability to create 8(a) joint ventures.  Eligible for assistance

  4. EM's Acting Assistant Secretary Selected to Lead Joint Convention

    Broader source: Energy.gov [DOE]

    The Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management (Joint Convention) selected David Huizenga, Acting Assistant Secretary for the Office of Environmental Management, as the President for the Fifth Review Meeting of the Parties.

  5. Joint Fuel Cell Bus Workshop Summary Report | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Cell Bus Workshop Summary Report Joint Fuel Cell Bus Workshop Summary Report Presentation at DOE & DOT Joint Fuel Cell Bus Workshop, June 7, 2010 PDF icon buswksp10_summary.pdf More Documents & Publications Fuel Cell Bus Workshop HybriDrive Propulsion System Fuel Cell Buses in U.S. Transit Fleets: Summary of Experiences and Current Status

  6. Majorana Demonstrator Bolted Joint Mechanical and Thermal Analysis

    SciTech Connect (OSTI)

    Aguayo Navarrete, Estanislao; Reid, Douglas J.; Fast, James E.

    2012-06-01

    The MAJORANA DEMONSTRATOR is designed to probe for neutrinoless double-beta decay, an extremely rare process with a half-life in the order of 1026 years. The experiment uses an ultra-low background, high-purity germanium detector array. The germanium crystals are both the source and the detector in this experiment. Operating these crystals as ionizing radiation detectors requires having them under cryogenic conditions (below 90 K). A liquid nitrogen thermosyphon is used to extract the heat from the detectors. The detector channels are arranged in strings and thermally coupled to the thermosyphon through a cold plate. The cold plate is joined to the thermosyphon by a bolted joint. This circular plate is housed inside the cryostat can. This document provides a detailed study of the bolted joint that connects the cold plate and the thermosyphon. An analysis of the mechanical and thermal properties of this bolted joint is presented. The force applied to the joint is derived from the torque applied to each one of the six bolts that form the joint. The thermal conductivity of the joint is measured as a function of applied force. The required heat conductivity for a successful experiment is the combination of the thermal conductivity of the detector string and this joint. The thermal behavior of the joint is experimentally implemented and analyzed in this study.

  7. Scanned_Joint_Declaration_(Italian).pdf | Department of Energy

    Energy Savers [EERE]

    Italian).pdf Scanned_Joint_Declaration_(Italian).pdf PDF icon Scanned_Joint_Declaration_(Italian).pdf More Documents & Publications FTCP Face to Face Meeting - March 30, 2010 Introducción al Conocimiento de Energía Energy Education Resources in Spanish Get Current: Switch on Clean Energy Coloring Book

  8. Science Programs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Programs /science-innovation/_assets/images/icon-science.jpg Science Programs The focal point for basic and applied R&D programs with a primary focus on energy but also encompassing medical, biotechnology, high-energy physics, and advanced scientific computing programs. Applied Energy Programs» Civilian Nuclear Programs» Laboratory Directed Research & Development» Office of Science»

  9. Joint Statement of the U.S.-Iraq Joint Coordinating Committee...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of the ongoing energy capacity building programs conducted by the U.S. Department of Commerce Commercial Law Development Program and the U.S. Agency for International Development. ...

  10. SCIENCE Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program early science program Early at the Argonne Leadership Computing Facility CONTACT Argonne Leadership Computing Facility | www.alcf.anl.gov | (877) 737-8615...

  11. Program Administration

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1997-08-21

    This volume describes program administration that establishes and maintains effective organizational management and control of the emergency management program. Canceled by DOE G 151.1-3.

  12. Breaking the Biological Barriers to Cellulosic Ethanol: A Joint Research Agenda

    SciTech Connect (OSTI)

    Houghton, John; Weatherwax, Sharlene; Ferrell, John

    2006-06-07

    The Biomass to Biofuels Workshop, held December 79, 2005, was convened by the Department of Energys Office of Biological and Environmental Research in the Office of Science; and the Office of the Biomass Program in the Office of Energy Efficiency and Renewable Energy. The purpose was to define barriers and challenges to a rapid expansion of cellulosic-ethanol production and determine ways to speed solutions through concerted application of modern biology tools as part of a joint research agenda. Although the focus was ethanol, the science applies to additional fuels that include biodiesel and other bioproducts or coproducts having critical roles in any deployment scheme.

  13. Remote controlled vacuum joint closure mechanism

    DOE Patents [OSTI]

    Doll, David W. (San Diego, CA); Hager, E. Randolph (La Jolla, CA)

    1986-01-01

    A remotely operable and maintainable vacuum joint closure mechanism for a noncircular aperture is disclosed. The closure mechanism includes an extendible bellows coupled at one end to a noncircular duct and at its other end to a flange assembly having sealed grooves for establishing a high vacuum seal with the abutting surface of a facing flange which includes an aperture forming part of the system to be evacuated. A plurality of generally linear arrangements of pivotally coupled linkages and piston combinations are mounted around the outer surface of the duct and aligned along the length thereof. Each of the piston/linkage assemblies is adapted to engage the flange assembly by means of a respective piston and is further coupled to a remote controlled piston drive shaft to permit each of the linkages positioned on a respective flat outer surface of the duct to simultaneously and uniformly displace a corresponding piston and the flange assembly with which it is in contact along the length of the duct in extending the bellows to provide a high vacuum seal between the movable flange and the facing flange. A plurality of latch mechanisms are also pivotally mounted on the outside of the duct. A first end of each of the latch mechanisms is coupled to a remotely controlled latch control shaft for displacing the latch mechanism about its pivot point. In response to the pivoting displacement of the latch mechanism, a second end thereof is displaced so as to securely engage the facing flange.

  14. The institutional needs of joint implementation projects

    SciTech Connect (OSTI)

    Watt, E.; Sathaye, J.; Buen, O. de; Masera, O.; Gelil, I.A.; Ravindranath, N.H.; Zhou, D.; Li, J.; Intarapravich, D.

    1995-10-21

    In this paper, the authors discuss options for developing institutions for joint implementation (JI) projects. They focus on the tasks which are unique to JI projects or require additional institutional needs--accepting the project by the host and investor countries and assessing the project`s greenhouse gas (GHG) emission reduction or sequestration--and they suggest the types of institutions that would enhance their performance. The evaluation is based on four sets of governmental and international criteria for JI projects, the experiences of ten pilot JI projects, and the perspectives of seven collaborating authors from China, Egypt, India, Mexico, and Thailand, who interviewed relevant government and non-government staff involved in JI issue assessment in their countries. After examining the roles for potential JI institutions, they present early findings arguing for a decentralized national JI structure, which includes: (1) national governmental panels providing host country acceptance of proposed JI projects; (2) project parties providing the assessment data on the GHG reduction or sequestration for the projects; (3) technical experts calculating these GHG flows; (4) certified verification teams checking the GHG calculations; and (5) members of an international JI Secretariat training and certifying the assessors, as well as resolving challenges to the verifications. 86 refs.

  15. Visiting Faculty Program Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Visiting Faculty Program Program Description The Visiting Faculty Program seeks to increase the research competitiveness of faculty members and their students at institutions historically underrepresented in the research community in order to expand the workforce vital to Department of Energy mission areas. As part of the program, selected university/college faculty members collaborate with DOE laboratory research staff on a research project of mutual interest. Program Objective The program is

  16. Proceedings of the Third International Workshop on Jointed Structures.

    SciTech Connect (OSTI)

    Starr, Michael James; Brake, Matthew Robert; Segalman, Daniel Joseph; Bergman, Lawrence A.; Ewins, David J.

    2013-08-01

    The Third International Workshop on Jointed Structures was held from August 16th to 17th, 2012, in Chicago Illinois, following the ASME 2012 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. Thirty two researchers from both the United States and international locations convened to discuss the recent progress of mechanical joints related research and associated efforts in addition to developing a roadmap for the challenges to be addressed over the next five to ten years. These proceedings from the workshop include the minutes of the discussions and follow up from the 2009 workshop [1], presentations, and outcomes of the workshop. Specifically, twelve challenges were formulated from the discussions at the workshop, which focus on developing a better understanding of uncertainty and variability in jointed structures, incorporating high fidelity models of joints in simulations that are tractable/efficient, motivating a new generation of researchers and funding agents as to the importance of joint mechanics research, and developing new insights into the physical phenomena that give rise to energy dissipation in jointed structures. The ultimate goal of these research efforts is to develop a predictive model of joint mechanics.

  17. Visiting Faculty Program Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    covers stipend and travel reimbursement for the 10-week program. Teacherfaculty participants: 1 Program Coordinator: Scott Robbins Email: srobbins@lanl.gov Phone number: 663-5621...

  18. SEALING LARGE-DIAMETER CAST-IRON PIPE JOINTS UNDER LIVE CONDITIONS

    SciTech Connect (OSTI)

    Kiran M. Kothari; Gerard T. Pittard

    2003-01-01

    Utilities in the U.S. operate over 75,000 km (47,000 miles) of old cast-iron pipes for gas distribution. The bell-and-spigot joints tend to leak as these pipes age. Current repair practices are costly and highly disruptive. The objective of this program is to design, test and commercialize a robotic system capable of sealing multiple cast-iron bell and spigot joints from a single pipe entry point. The proposed system will perform repairs while the pipe remains in service by traveling through the pipe, cleaning each joint surface, and attaching a stainless-steel sleeve lined with an epoxy-impregnated felt across the joint. This approach will save considerable time and labor, avoid traffic disruption, and eliminate any requirement to interrupt service (which results in enormous expense to utilities). Technical challenges include: (1) repair sleeves must compensate for diametric variation and eccentricity of cast-iron pipes; (2) the assembly must travel long distances through pipes containing debris; (3) the pipe wall must be effectively cleaned in the immediate area of the joint to assure good bonding of the sleeve; and (4) an innovative bolt-on entry fitting is required to conduct repair operations on live mains. The development effort is divided into eleven tasks. Task 1--Program Management was previously completed. Two reports, one describing the program management plan and the other consisting of the technology assessment, were submitted to the DOE COR in the first quarter. Task 2--Establishment of Detailed Design Specifications and Task 3--Design and Fabricate Ratcheting Stainless-Steel Repair Sleeves are now well underway. First-quarter activities included conducting detailed analyses to determine the capabilities of coiled-tubing locomotion for entering and repairing gas mains and the first design iteration of the joint-sealing sleeve. The maximum horizontal reach of coiled tubing inside a pipeline before buckling prevents further access was calculated for a wide range of coiled-tubing string designs and pipe environments. Work conducted in the second quarter consisted of: (1) selecting a preferred pan/zoom/tilt camera; (2) initiating design of the digital control electronics and switching power supply for the control and operation of the in-pipe robotic modules; (3) continuing design of the repair sleeve and (4) initial testing of the wall-cleaning device. Most recently, activities in the third quarter included: (1) development of the system's pan/zoom/tilt camera control electronics and operating software, and implementing these in the surface and downhole modules and (2) further testing of the wall-cleaning elements used to clean the inside of the bell and spigot joints. Details of these activities are described in the body of the report along with a summary of events scheduled for the fourth quarter.

  19. SEALING LARGE-DIAMETER CAST-IRON PIPE JOINTS UNDER LIVE CONDITIONS

    SciTech Connect (OSTI)

    Kiran M. Kothari; Gerard T. Pittard

    2003-06-01

    Utilities in the U.S. operate over 75,000 km (47,000 miles) of old cast-iron pipes for gas distribution. The bell-and-spigot joints tend to leak as these pipes age. Current repair practices are costly and highly disruptive. The objective of this program is to design, test and commercialize a robotic system capable of sealing multiple cast-iron bell and spigot joints from a single pipe entry point. The proposed system will perform repairs while the pipe remains in service by traveling through the pipe, cleaning each joint surface, and attaching a stainless-steel sleeve lined with an epoxy-impregnated felt across the joint. This approach will save considerable time and labor, avoid traffic disruption, and eliminate any requirement to interrupt service (which results in enormous expense to utilities). Technical challenges include: (1) repair sleeves must compensate for diametric variation and eccentricity of cast-iron pipes; (2) the assembly must travel long distances through pipes containing debris; (3) the pipe wall must be effectively cleaned in the immediate area of the joint to assure good bonding of the sleeve; and (4) an innovative bolt-on entry fitting is required to conduct repair operations on live mains. The development effort is divided into eleven tasks. Task 1-Program Management was previously completed. Two reports, one describing the program management plan and the other consisting of the technology assessment, were submitted to the DOE COR in the first quarter. Task 2-Establishment of Detailed Design Specifications and Task 3-Design and Fabricate Ratcheting Stainless-Steel Repair Sleeves are now well underway. First-quarter activities included conducting detailed analyses to determine the capabilities of coiled-tubing locomotion for entering and repairing gas mains and the first design iteration of the joint-sealing sleeve. The maximum horizontal reach of coiled tubing inside a pipeline before buckling prevents further access was calculated for a wide range of coiled-tubing string designs and pipe environments. Work conducted in the second quarter consisted of: (1) selecting a preferred pan/zoom/tilt camera; (2) initiating design of the digital control electronics and switching power supply for the control and operation of the in-pipe robotic modules; (3) continuing design of the repair sleeve and (4) initial testing of the wall-cleaning device. Activities in the third quarter included: (1) development of the system's pan/zoom/tilt camera control electronics and operating software, and implementing these in the surface and downhole modules and (2) further testing of the wall-cleaning elements used to clean the inside of the bell and spigot joints. Most recently, fourth quarter developments were centered on designing and testing the pipe-wall cleaning device including the selection of the drive motor and its control electronics. In addition, efforts were also focused on the design of the repair sleeve. Details of these activities are described in the body of the report along with a summary of events scheduled for the next quarter.

  20. Community Programs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Community Programs Community Berkeley Global Campus Environmental Documents Tours Community Programs Friends of Berkeley Lab ⇒ Navigate Section Community Berkeley Global Campus Environmental Documents Tours Community Programs Friends of Berkeley Lab Community Education Programs Workforce Development & Education As part of the Lab's education mission to inspire and prepare the next generation of scientists and engineers, the Workforce Development & Education runs numerous education

  1. US, Russian Federation Sign Joint Statement on Reactor Conversion |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy US, Russian Federation Sign Joint Statement on Reactor Conversion US, Russian Federation Sign Joint Statement on Reactor Conversion June 26, 2012 - 12:00pm Addthis News Media Contact (202) 586-4940 This release is cross-posted from NNSA.energy.gov. MOSCOW - The U.S. and Russian Federation jointly announced today that the first stage of work defined in the Implementing Agreement between the Russian State Corporation for Atomic Energy (Rosatom) and the Department of Energy

  2. Ultrasonic inspection of polyethylene butt-fussion joints

    SciTech Connect (OSTI)

    House, L.J.; Day, R.A.

    1982-01-01

    Researchers investigated nondestructive pulse-echo, pitch-catch, and spectroscopic ultrasonic methods for determining voids and inclusions, lack of bond, and inadequate fusion in heat-fused polyethylene butt joints in 4-in. gas distribution pipe. The pulse-echo method, using a 2.25-MHz, cylindrically focused transducer, provided the best sensitivity to the joint defects, detecting flaws as small as 0.014 in. in diameter. No correlation was established between the ultrasonic spectroscopy results and the cohesive strength of incompletely fused joints in the 1.2-3.2 MHz frequency range.

  3. Introduction to Using NERSC for the Joint Genome Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NERSC Introduction to Using NERSC for the Joint Genome Institute May 2, 2011 jgi logo sm NERSC Training Event 1:00-5:00 p.m. PDT May 2, 2011 Joint Genome Institute, 2800 Mitchell Drive, Walnut Creek, CA Introduction to Using NERSC Richard Gerber, NERSC User Services Group Shane Canon, NERSC Technology Integration Group This half-day training will enable new users from the Joint Genome Institute to get connected and running jobs at NERSC. We will cover NERSC computational and storage systems,

  4. Joint NERSC/OLCF/NICS Cray XT5 Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Events » Joint NERSC/OLCF/NICS Cray XT5 Workshop Joint NERSC/OLCF/NICS Cray XT5 Workshop February 1, 2010 February 1-3, 2010 Berkeley, CA The Joint Cray XT5 Workshop is designed to provide an in-depth introduction to using the world's newest and largest Cray XT5 systems. Representatives and staff from the National Energy Research Scientific Computing Center, the Oak Ridge Leadership Computing Facility, the National Institute for Computational Science, Cray, and AMD will explain how to use XT5

  5. Smart Power Infrastructure Demonstration for Energy Reliability and Security (SPIDERS) Joint Capability Technology Demonstration (JCTD) Phase III

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Capability Technology Demonstration (JCTD) Industry Day Mr. Tarek Abdallah OSD JCTD Technical Manager Aug 27, 2015 SPIDERS Overview and Objectives Program Objectives: - Energy Security (measured by off-grid mission endurance)* - Increase Renewable Energy Contribution during contingency - Reduce Environmental Impact of Facility Operations - Increase Cyber Security of Facility Operations * Remember, in DoD its "Mission, Mission, Mission!" Where We Are Today CAMP SMITH ENERGY ISLAND

  6. Final Joint Statement from G-7 Energy Ministers Meeting in Rome...

    Broader source: Energy.gov (indexed) [DOE]

    Final Joint Statement from G-7 Energy Ministers Meeting in Rome More Documents & Publications Final Joint Statement from G-7 Energy Ministers Meeting in Rome Before the Senate...

  7. Time-lapse Joint Inversion of Geophysical Data and its Applications...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Time-lapse Joint Inversion of Geophysical Data and its Applications to Geothermal Prospecting Time-lapse Joint Inversion of Geophysical Data and its Applications to Geothermal ...

  8. Remote controlled vacuum joint closure mechanism

    DOE Patents [OSTI]

    Doll, D.W.; Hager, E.R.

    1984-02-22

    A remotely operable and maintainable vacuum joint closure mechanism for a noncircular aperture is disclosed. The closure mechanism includes an extendible bellows coupled at one end to a noncircular duct and at its other end to a flange assembly having sealed grooves for establishing a high vacuum seal with the abutting surface of a facing flange which includes an aperture forming part of the system to be evacuated. A plurality of generally linear arrangements of pivotally coupled linkages and piston combinations are mounted around the outer surface of the duct and aligned along the length thereof. Each of the piston/linkage assemblies is adapted to engage the flange assembly by means of a respective piston and is further coupled to a remote controlled piston drive shaft to permit each of the linkages positioned on a respective flat outer surface of the duct to simultaneously and uniformly displace a corresponding piston and the flange assembly with which it is in contact along the length of the duct in extending the bellows to provide a high vacuum seal between the movable flange and the facing flange. A plurality of latch mechanisms are also pivotally mounted on the outside of the duct. A first end of each of the latch mechanisms is coupled to a remotely controlled latch control shaft for displacing the latch mechanism about its pivot point. In response to the pivoting displacement of the latch mechanism, a second end thereof is displaced so as to securely engage the facing flange and maintain the high vacuum seal established by the displacement of the flange assembly and extension of the bellows without displacing the entire duct.

  9. US - Brazil Binational Energy Working Group Joint Action Plan | Department

    Broader source: Energy.gov (indexed) [DOE]

    of Energy PDF icon brazil_actionplan_7202010.pdf More Documents & Publications U.S.-Brazil Binational Joint Action Plan Webtrends Archives by Fiscal Year - International Activities EIS-0309: Record of Decision

  10. Gas turbine igniter with ball-joint support

    SciTech Connect (OSTI)

    Steber, C.E.; Travis, R.J.; Rizzo, J.A.

    1990-02-27

    This patent describes a support for an igniter for a combustor of a gas turbine, the combustor being of a type including a casing and a liner within the casing. It comprises: a ball joint; means for supporting the ball joint disposed a substantial distance outward from the casing; a body section of the igniter affixed in the ball joint; means for permitting the ball joint, and the body section to rotate through a substantial range; an igniter tip on the body section; and a hole in the liner. The igniter tip entering through the hole and into an interior of the liner. The hole being a tight fit to the igniter tip, whereby leakage past the igniter tip through the hole is limited. The substantial range being sufficient to permit fitting the igniter tip in the hole in the presence of manufacturing tolerances, and to permit the igniter tip to track the hole in the presence of differential thermal expansion during operation.

  11. Method of forming a ceramic to ceramic joint

    DOE Patents [OSTI]

    Cutler, Raymond Ashton; Hutchings, Kent Neal; Kleinlein, Brian Paul; Carolan, Michael Francis

    2010-04-13

    A method of joining at least two sintered bodies to form a composite structure, includes: providing a joint material between joining surfaces of first and second sintered bodies; applying pressure from 1 kP to less than 5 MPa to provide an assembly; heating the assembly to a conforming temperature sufficient to allow the joint material to conform to the joining surfaces; and further heating the assembly to a joining temperature below a minimum sintering temperature of the first and second sintered bodies. The joint material includes organic component(s) and ceramic particles. The ceramic particles constitute 40-75 vol. % of the joint material, and include at least one element of the first and/or second sintered bodies. Composite structures produced by the method are also disclosed.

  12. Mechanical properties of dissimilar metal joints composed of...

    Office of Scientific and Technical Information (OSTI)

    of dissimilar metal joints composed of DP 980 Steel and AA 7075-T6 A solid-state joining process, called friction bit joining (FBJ), was used to spot weld aluminum alloy 7075-T6...

  13. Joint comments of consumers energy company and the detriot edison...

    Office of Environmental Management (EM)

    the Northeast Power Coordinating Council FE Docket No. 99-1 Joint Motion to Intervene of Northern States Power Company (Minnesota) et al. on the Proposed Open Access Requirements...

  14. United States -- Mexican joint ventures: A case history approach

    SciTech Connect (OSTI)

    Moore, N.L.; Chidester, R.J.; Hughes, K.R.; Fowler, R.A.

    1993-03-01

    Because the Mexican government has encouraged investment in Mexico by increasing the percentage of ownership of a Mexican business that a US company can hold, joint ventures are more attractive now than they had been in the past. This study provides preliminary information for US renewable energy companies who are interested in forming a joint venture with a Mexican company. This report is not intended to be a complete reference but does identifies a number of important factors that should be observed when forming a Mexican joint venture: (1)Successful joint ventures achieve the goals of each partner. (2)It is essential that all parties agree to the allocation of responsibilities. (3)Put everything in writing. (4)Research in depth the country or countries in which you are considering doing business.

  15. Montana Joint Application for Proposed Work in Streams, Lakes...

    Open Energy Info (EERE)

    Streams, Lakes and Wetlands Webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Montana Joint Application for Proposed Work in Streams, Lakes and...

  16. Y-12 presented with joint resolution honoring 70th anniversary...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Posted: September 24, 2015 - 11:17am Ray Smith (left) accepts a copy of a joint resolution ... The resolution was presented to Y-12 historian Ray Smith at an Aug. 29 event in Oak Ridge. ...

  17. Seismic Capacity of Threaded, Brazed, and Grooved Pipe Joints

    Office of Environmental Management (EM)

    joints * 4 tests o Brazed (copper) * 4 tests Grooved Couplings o Catalog items o ASTM A106 Grade B piping o ASTM A 536 couplings o Lateral deflections imposed well above...

  18. DOE Joint BioEnergy Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear Energy Nuclear

  19. Joint Final Environmental Impact Statement Montanore Project

    Office of Environmental Management (EM)

    2 Chapter 3: Affected Environment and Environmental Consequences Section 3.7, Cultural Resources through Section 3.24, Wilderness, Roadless Areas, and Wild and Scenic Rivers United States Department of Agriculture Forest Service Northern Region Kootenai National Forest Montana Department of Environmental Quality The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age, disability, and where applicable,

  20. Joint Final Environmental Impact Statement Montanore Project

    Office of Environmental Management (EM)

    3 Chapter 3: Affected Environment and Environmental Consequences Section 3.25, Wildlife through Section 3.26, Other Required Disclosures Chapter 4, Consultation and Coordination through Chapter 8, References United States Department of Agriculture Forest Service Northern Region Kootenai National Forest Montana Department of Environmental Quality The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age,

  1. Joint Coordinating Committee | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Coordinating Committee | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios Congressional Testimony Fact Sheets Newsletters Press Releases Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at

  2. Climate Models from the Joint Global Change Research Institute

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Staff at the Joint Institute develop and use models to simulate the economic and physical impacts of global change policy options. The GCAM, for example, gives analysts insight into how regional and national economies might respond to climate change mitigation policies including carbon taxes, carbon trading, and accelerated deployment of energy technology. Three available models are Phoenix, GCAM, and EPIC. Phoenix is a global, dynamic recursive, computable general equilibrium model that is solved in five-year time steps from 2005 through 2100 and divides the world into twenty-four regions. Each region includes twenty-six industrial sectors. Particular attention is paid to energy production in Phoenix. There are nine electricity-generating technologies (coal, natural gas, oil, biomass, nuclear, hydro, wind, solar, and geothermal) and four additional energy commodities: crude oil, refined oil products, coal, and natural gas. Phoenix is designed to answer economic questions related to international climate and energy policy and international trade. Phoenix replaces the Second Generation Model (SGM) that was formerly used for general equilibrium analysis at JGCRI. GCAM is the Global Change Assessment Model, a partial equilibrium model of the world with 14 regions. GCAM operates in 5 year time steps from 1990 to 2095 and is designed to examine long-term changes in the coupled energy, agriculture/land-use, and climate system. GCAM includes a 151-region agriculture land-use module and a reduced form carbon cycle and climate module in addition to its incorporation of demographics, resources, energy production and consumption. The model has been used extensively in a number of assessment and modeling activities such as the Energy Modeling Forum (EMF), the U.S. Climate Change Technology Program, and the U.S. Climate Change Science Program and IPCC assessment reports. GCAM is now freely available as a community model. The Environmental Policy Integrated Climate (EPIC) Model is a process-based agricultural systems model composed of simulation components for weather, hydrology, nutrient cycling, pesticide fate, tillage, crop growth, soil erosion, crop and soil management and economics. Staff at PNNL have been involved in the development of this model by integrating new sub-models for soil carbon dynamics and nitrogen cycling.

  3. Accreditation Management of Superior Energy Performance Program to

    Office of Environmental Management (EM)

    Transition Solely to ANAB in 2016 | Department of Energy Accreditation Management of Superior Energy Performance Program to Transition Solely to ANAB in 2016 Accreditation Management of Superior Energy Performance Program to Transition Solely to ANAB in 2016 February 2, 2016 - 10:24am Addthis Since its inception, Superior Energy Performance (SEP) program accreditation has been jointly managed by both the American National Standards Institute (ANSI) and the ANSI-ASQ National Accreditation

  4. Senior International Energy Officials Issue Joint Statement in Support of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the Global Nuclear Energy Partnership | Department of Energy International Energy Officials Issue Joint Statement in Support of the Global Nuclear Energy Partnership Senior International Energy Officials Issue Joint Statement in Support of the Global Nuclear Energy Partnership May 21, 2007 - 12:55pm Addthis WASHINGTON, DC - U.S. Secretary of Energy Samuel W. Bodman today announced that the U.S. Department of Energy (DOE) and senior energy officials from some of the world's leading economies

  5. U.S. - Pakistan Joint Press Statement | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    - Pakistan Joint Press Statement U.S. - Pakistan Joint Press Statement March 13, 2006 - 11:50am Addthis ISLAMABAD, PAKISTAN - As agreed during President Bush's visit to Pakistan on 3-4 March 2006, U.S. Secretary of Energy Samuel Bodman visited Islamabad today to discuss a wide range of issues related to Pakistan's growing energy needs. Secretary Bodman's visit symbolizes the strengthened and expanded relationship between the United States and Pakistan over the last five years. Closer

  6. ORISE: Providing Support to the DOE Joint Information Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Joint Information Center (JIC) ORISE supports DOE's Oak Ridge Office by managing crisis communication facility for drills, exercises and emergencies In the event of an emergency, the U.S. Department of Energy (DOE) Oak Ridge Office (ORO) Joint information Center (JIC) may be activated. The Oak Ridge Institute for Science and Education (ORISE) supports the DOE ORO JIC with training, management of the JIC facility, and onsite advisory capabilities. How ORISE is Making a Difference Specifically,

  7. Computing and Computational Sciences Directorate - Joint Institute for

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Computational Sciences Joint Institute for Computational Sciences To help realize the full potential of new-generation computers for advancing scientific discovery, the University of Tennessee (UT) and Oak Ridge National Laboratory (ORNL) have created the Joint Institute for Computational Sciences (JICS). JICS combines the experience and expertise in theoretical and computational science and engineering, computer science, and mathematics in these two institutions and focuses these skills on

  8. Rooted in Wonder: Joint Genome Institute Study Reveals Amazing World

    Energy Savers [EERE]

    Underfoot | Department of Energy Rooted in Wonder: Joint Genome Institute Study Reveals Amazing World Underfoot Rooted in Wonder: Joint Genome Institute Study Reveals Amazing World Underfoot August 13, 2012 - 2:33pm Addthis By developing a better understanding of the microbes that affect the growth of other plants (crops like corn or wheat) researchers may be able to improve their growth -- or provide better care for them in times of drought. By developing a better understanding of the

  9. Oil shale, tar sand, coal research advanced exploratory process technology, jointly sponsored research

    SciTech Connect (OSTI)

    Speight, J.G.

    1992-01-01

    Accomplishments for the past quarter are presented for the following five tasks: oil shale; tar sand; coal; advanced exploratory process technology; and jointly sponsored research. Oil shale research covers oil shale process studies. Tar sand research is on process development of Recycle Oil Pyrolysis and Extraction (ROPE) Process. Coal research covers: coal combustion; integrated coal processing concepts; and solid waste management. Advanced exploratory process technology includes: advanced process concepts;advanced mitigation concepts; and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; CROW field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; PGI demonstration project; operation and evaluation of the CO[sub 2] HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesaverde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced oil recovery techniques; surface process study for oil recovery using a thermal extraction process; NMR analysis of samples from the ocean drilling program; in situ treatment of manufactured gas plant contaminated soils demonstration program; and solid state NMR analysis of naturally and artificially matured kerogens.

  10. Iron aluminide alloy coatings and joints, and methods of forming

    DOE Patents [OSTI]

    Wright, R.N.; Wright, J.K.; Moore, G.A.

    1994-09-27

    Disclosed is a method of joining two bodies together, at least one of the bodies being predominantly composed of metal, the two bodies each having a respective joint surface for joining with the joint surface of the other body, the two bodies having a respective melting point, includes the following steps: (a) providing aluminum metal and iron metal on at least one of the joint surfaces of the two bodies; (b) after providing the aluminum metal and iron metal on the one joint surface, positioning the joint surfaces of the two bodies in juxtaposition against one another with the aluminum and iron positioned therebetween; (c) heating the aluminum and iron on the juxtaposed bodies to a temperature from greater than or equal to 600 C to less than the melting point of the lower melting point body; (d) applying pressure on the juxtaposed surfaces; and (e) maintaining the pressure and the temperature for a time period effective to form the aluminum and iron into an iron aluminide alloy joint which bonds the juxtaposed surfaces and correspondingly the two bodies together. The method can also effectively be used to coat a body with an iron aluminide coating.

  11. Iron aluminide alloy coatings and joints, and methods of forming

    DOE Patents [OSTI]

    Wright, Richard N. (Idaho Falls, ID); Wright, Julie K. (Idaho Falls, ID); Moore, Glenn A. (Idaho Falls, ID)

    1994-01-01

    A method of joining two bodies together, at least one of the bodies being predominantly composed of metal, the two bodies each having a respective joint surface for joining with the joint surface of the other body, the two bodies having a respective melting point, includes the following steps: a) providing aluminum metal and iron metal on at least one of the joint surfaces of the two bodies; b) after providing the aluminum metal and iron metal on the one joint surface, positioning the joint surfaces of the two bodies in juxtaposition against one another with the aluminum and iron positioned therebetween; c) heating the aluminum and iron on the juxtaposed bodies to a temperature from greater than or equal to 600.degree. C. to less than the melting point of the lower melting point body; d) applying pressure on the juxtaposed surfaces; and e) maintaining the pressure and the temperature for a time period effective to form the aluminum and iron into an iron aluminide alloy joint which bonds the juxtaposed surfaces and correspondingly the two bodies together. The method can also effectively be used to coat a body with an iron aluminide coating.

  12. Program Automation

    Broader source: Energy.gov [DOE]

    Better Buildings Residential Network Data and Evaluation Peer Exchange Call Series: Program Automation, Call Slides and Discussion Summary, November 21, 2013. This data and evaluation peer exchange call discussed program automation.

  13. Retiree Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Library Services » Retiree Program Retiree Program The Research Library offers a 1 year library card to retired LANL employees that allows usage of Library materials. This service is only available to retired LANL employees. Who is eligible? Any Laboratory retiree, not participating in any other program (ie, Guest Scientist, Affiliate). Upon completion of your application, you will be notified of your acceptance into the program. This does not include past students. What is the term of the

  14. HVAC Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Commercial Program Development Commercial Current Promotions Industrial Federal Agriculture Heating Ventilation and Air Conditioning Energy efficient Heating Ventilation and...

  15. Laboratory for Nuclear Science. High Energy Physics Program

    SciTech Connect (OSTI)

    Milner, Richard

    2014-07-30

    High energy and nuclear physics research at MIT is conducted within the Laboratory for Nuclear Science (LNS). Almost half of the faculty in the MIT Physics Department carry out research in LNS at the theoretical and experimental frontiers of subatomic physics. Since 2004, the U.S. Department of Energy has funded the high energy physics research program through grant DE-FG02-05ER41360 (other grants and cooperative agreements provided decades of support prior to 2004). The Director of LNS serves as PI. The grant supports the research of four groups within LNS as tasks within the umbrella grant. Brief descriptions of each group are given here. A more detailed report from each task follows in later sections. Although grant DE-FG02-05ER41360 has ended, DOE continues to fund LNS high energy physics research through five separate grants (a research grant for each of the four groups, as well as a grant for AMS Operations). We are pleased to continue this longstanding partnership.

  16. CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR

    Broader source: Energy.gov [DOE]

    2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  17. SPR Process Simulation, Analyses, & Development for Mg Joints

    Broader source: Energy.gov [DOE]

    2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  18. Framing the Energy Technology Menu

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Future of Coal and Nuclear Power Ernest J. Moniz Cecil and Ida Green Professor of Physics and Engineering Systems Director, MIT Energy Initiative EIA April 2008 2 NAE Engineering Achievement of the Twentieth Century l Electrification l Reflects both the technological challenge of this continent- scale system and the ubiquitous contribution to quality of life 3 Annual Per Capita Electricity Use (kWh) 4 MIT Joint Program on the Science and Policy of Global Change H. Jacoby and R. Prinn,

  19. Joint Statement of Intent Concerning the Arak Heavy Water Reactor Research Reactor Modernization Project under the Joint Comprehensive Plan of Action

    Broader source: Energy.gov [DOE]

    Joint statement on future steps of the modernization of the Arak reactor as contemplated in the Joint Comprehensive Plan of Action of July 14, 2015 (JCPOA) and United Nations Security Council Resolution 2231.

  20. Fact Sheet: United States-Japan Joint Nuclear Energy Action Plan |

    Office of Environmental Management (EM)

    Department of Energy United States-Japan Joint Nuclear Energy Action Plan Fact Sheet: United States-Japan Joint Nuclear Energy Action Plan PDF icon Fact Sheet: United States-Japan Joint Nuclear Energy Action Plan More Documents & Publications United States -Japan Joint Nuclear Energy Action Plan US-Japan_NuclearEnergyActionPlan.pdf United States-Japan Joint Nuclear Energy Action Plan

  1. Sandia National Laboratories: Careers: Special Programs: Nonlinear

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mechanics and Dynamics Research Institute Research Institute Wounded Warrior Career Development Program Careers Nonlinear Mechanics and Dynamics Research Institute FEA modeling simulation A test specimen for measuring dissipation across a lap joint under different loading environments (top), and Finite Element Analysis (FEA) predictions for the same system (bottom). When offered The six-week institute will begin on June 20, 2016, and will end on July 29, 2016. Afterwards, participants will

  2. La Vida Robot - High School Engineering Program Combats Engineering Brain Drain

    ScienceCinema (OSTI)

    Cameron, Allan; Fredi, Lajvardi

    2009-09-01

    Carl Hayden High School has built an impressive reputation with its robotics club. At a time when interest in science, math and engineering is declining, the Falcon Robotics club has young people fired up about engineering. Their program in underwater robots (MATE) and FIRST robotics is becoming a national model, not for building robots, but for building engineers. Teachers Fredi Lajvardi and Allan Cameron will present their story (How kids 'from the mean streets of Phoenix took on the best from M.I.T. in the national underwater bot championship' - Wired Magazine, April 2005) and how every student needs the opportunity to 'do real engineering.'

  3. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Description Inspiring girls to recognize their potential and pursue opportunities in science, technology, engineering and mathematics. Through Expanding Your Horizon (EYH) Network programs, we provide STEM role models and hands-on activities for middle and high school girls. Our ultimate goal is to motivate girls to become innovative and creative thinkers ready to meet 21st century challenges. The EYH Network's programs are based on the following assumptions: 1. In order to increase the

  4. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Description SAGE, the Summer of Applied Geophysical Experience, is a unique educational program designed to introduce students in geophysics and related fields to "hands on" geophysical exploration and research. The program emphasizes both teaching of field methods and research related to basic science and a variety of applied problems. SAGE is hosted by the National Security Education Center and the Earth and Environmental Sciences Division of the Los Alamos National

  5. exercise program

    National Nuclear Security Administration (NNSA)

    and dispose of many different hazardous substances, including radioactive materials, toxic chemicals, and biological agents and toxins.

    There are a few programs NNSA uses...

  6. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Applied Geophysical Experience, is a unique educational program designed to introduce students in geophysics and related fields to "hands on" geophysical exploration and research....

  7. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    their potential and pursue opportunities in science, technology, engineering and mathematics. Through Expanding Your Horizon (EYH) Network programs, we provide STEM role models...

  8. Counterintelligence Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1992-09-04

    To establish the policies, procedures, and specific responsibilities for the Department of Energy (DOE) Counterintelligence (CI) Program. This directive does not cancel any other directive.

  9. Programming Stage

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1997-05-21

    This chapter addresses plans for the acquisition and installation of operating environment hardware and software and design of a training program.

  10. Special Programs

    Office of Energy Efficiency and Renewable Energy (EERE)

    Headquarters Human Resources Operations promotes a variety of hiring flexibilities for managers to attract a diverse workforce, from Student Internship Program opportunities (Pathways), Veteran...

  11. Volunteer Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    National VolunteerMatch Retired and Senior Volunteer Program United Way of Northern New Mexico United Way of Santa Fe County Giving Employee Giving Campaign Holiday Food Drive...

  12. Program Summaries

    Office of Science (SC) Website

    Program Summaries Basic Energy Sciences (BES) BES Home About Research Facilities Science Highlights Benefits of BES Funding Opportunities Basic Energy Sciences Advisory Committee ...

  13. Counterintelligence Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2004-12-10

    The Order establishes Counterintelligence Program requirements and responsibilities for the Department of Energy, including the National Nuclear Security Administration. Supersedes DOE 5670.3.

  14. IMPACTS: Industrial Technologies Program, Summary of Program...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    IMPACTS: Industrial Technologies Program, Summary of Program Results for CY2009 IMPACTS: Industrial Technologies Program, Summary of Program Results for CY2009 PDF icon ...

  15. Addressing the Need for Alternative Transportation Fuels: The Joint

    Office of Scientific and Technical Information (OSTI)

    BioEnergy Institute (Journal Article) | SciTech Connect Addressing the Need for Alternative Transportation Fuels: The Joint BioEnergy Institute Citation Details In-Document Search Title: Addressing the Need for Alternative Transportation Fuels: The Joint BioEnergy Institute Today, carbon-rich fossil fuels, primarily oil, coal, and natural gas, provide 85% of the energy consumed in the U.S. As world demand increases, oil reserves may become rapidly depleted. Fossil fuel use increases CO{sub

  16. Joint Facilities User Forum on Data-Intensive Computing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Computing Joint Facilities User Forum on Data-Intensive Computing All logos June 16-18, 2014 Oakland City Center Conference Center 500 12th Street, Suite 105 Oakland, CA Directions and Site Brochure Held in conjunction with DOE HPC Operational Review (HPCOR) June 17-19, 2014 The Joint Facilities User Forum on Data-Intensive Computing will bring together users and HPC center staff to discuss successes, failures, lessons learned, and the future of data-driven scientific discovery. There will also

  17. Fundamentals of Delayed Coking Joint Industry Project

    SciTech Connect (OSTI)

    Michael Volk; Keith Wisecarver

    2003-09-26

    Delayed coking evolved steadily over the early to mid 1900s to enable refiners to convert high boiling, residual petroleum fractions to light products such as gasoline. Pound for pound, coking is the most energy intensive of any operation in a modern refinery. Large amounts of energy are required to heat the thick, poor-quality petroleum residuum to the 900 to 950 degrees F required to crack the heavy hydrocarbon molecules into lighter, more valuable products. One common misconception of delayed coking is that the product coke is a disadvantage. Although coke is a low valued (near zero economic value) byproduct, compared to transportation fuels, there is a significant worldwide trade and demand for coke as it is an economical fuel. Coke production has increased steadily over the last ten years, with further increases forecast for the foreseeable future. Current domestic production is near 111,000 tons per day. A major driving force behind this increase is the steady decline in crude quality available to refiners. Crude slates are expected to grow heavier with higher sulfur contents while environmental restrictions are expected to significantly reduce the demand for high-sulfur residual fuel oil. Light sweet crudes will continue to be available and in even greater demand than they are today. Refiners will be faced with the choice of purchasing light sweet crudes at a premium price, or adding bottom of the barrel upgrading capability, through additional new investments, to reduce the production of high-sulfur residual fuel oil and increase the production of low-sulfur distillate fuels. A second disadvantage is that liquid products from cokers frequently are unstable, i.e., they rapidly form gum and sediments. Because of intermediate investment and operating costs, delayed coking has increased in popularity among refiners worldwide. Based on the 2000 Worldwide Refining Survey published in the Oil and Gas, the delayed coking capacity for 101 refineries around the world is 2,937,439 barrels/calendar day. These cokers produce 154,607 tons of coke per day and delayed coking accounts for 88% of the world capacity. The delayed coking charge capacity in the United States is 1,787,860 b/cd. Despite its wide commercial use, only relatively few contractors and refiners are truly knowledgeable in delayed-coking design, so that this process carries with it a ''black art'' connotation. Until recently, the expected yield from cokers was determined by a simple laboratory test on the feedstock. As a result of Tulsa University's prior related research, a process model was developed that with additional work could be used to optimize existing delayed cokers over a wide range of potential feedstocks and operating conditions. The objectives of this research program are to: utilize the current micro, batch and pilot unit facilities at The University of Tulsa to enhance the understanding of the coking process; conduct additional micro and pilot unit tests with new and in-house resids and recycles to make current optimization models more robust; conduct focused kinetic experiments to enhance the furnace tube model and to enhance liquid production while minimizing sulfur in the products; conduct detailed foaming studies to optimize the process and minimize process upsets; quantify the parameters that affect coke morphology; and to utilize the knowledge gained from the experimental and modeling studies to enhance the computer programs developed in the previous JIP for optimization of the coking process. These refined computer models will then be tested against refinery data provided by the member companies. Novel concepts will also be explored for hydrogen sulfide removal of furnace gases as well as gas injection studies to reduce over-cracking.

  18. Fundamentals of Delayed Coking Joint Industry Project

    SciTech Connect (OSTI)

    Michael Volk; Keith Wisecarver

    2004-09-26

    Delayed coking evolved steadily over the early to mid 1900s to enable refiners to convert high boiling, residual petroleum fractions to light products such as gasoline. Pound for pound, coking is the most energy intensive of any operation in a modern refinery. Large amounts of energy are required to heat the thick, poor-quality petroleum residuum to the 900 to 950 degrees F required to crack the heavy hydrocarbon molecules into lighter, more valuable products. One common misconception of delayed coking is that the product coke is a disadvantage. Although coke is a low valued (near zero economic value) byproduct, compared to transportation fuels, there is a significant worldwide trade and demand for coke as it is an economical fuel. Coke production has increased steadily over the last ten years, with further increases forecast for the foreseeable future. Current domestic production is near 111,000 tons per day. A major driving force behind this increase is the steady decline in crude quality available to refiners. Crude slates are expected to grow heavier with higher sulfur contents while environmental restrictions are expected to significantly reduce the demand for high-sulfur residual fuel oil. Light sweet crudes will continue to be available and in even greater demand than they are today. Refiners will be faced with the choice of purchasing light sweet crudes at a premium price, or adding bottom of the barrel upgrading capability, through additional new investments, to reduce the production of high-sulfur residual fuel oil and increase the production of low-sulfur distillate fuels. A second disadvantage is that liquid products from cokers frequently are unstable, i.e., they rapidly form gum and sediments. Because of intermediate investment and operating costs, delayed coking has increased in popularity among refiners worldwide. Based on the 2000 Worldwide Refining Survey published in the Oil and Gas, the delayed coking capacity for 101 refineries around the world is 2,937,439 barrels/calendar day. These cokers produce 154,607 tons of coke per day and delayed coking accounts for 88% of the world capacity. The delayed coking charge capacity in the United States is 1,787,860 b/cd. Despite its wide commercial use, only relatively few contractors and refiners are truly knowledgeable in delayed-coking design, so that this process carries with it a ''black art'' connotation. Until recently, the expected yield from cokers was determined by a simple laboratory test on the feedstock. As a result of Tulsa University's prior related research, a process model was developed that with additional work could be used to optimize existing delayed cokers over a wide range of potential feedstocks and operating conditions. The objectives of this research program are to: utilize the current micro, batch and pilot unit facilities at The University of Tulsa to enhance the understanding of the coking process; conduct additional micro and pilot unit tests with new and in-house resids and recycles to make current optimization models more robust; conduct focused kinetic experiments to enhance the furnace tube model and to enhance liquid production while minimizing sulfur in the products; conduct detailed foaming studies to optimize the process and minimize process upsets; quantify the parameters that affect coke morphology; and to utilize the knowledge gained from the experimental and modeling studies to enhance the computer programs developed in the previous JIP for optimization of the coking process. These refined computer models will then be tested against refinery data provided by the member companies. Novel concepts will also be explored for hydrogen sulfide removal of furnace gases as well as gas injection studies to reduce over-cracking.

  19. AISI Direct Steelmaking Program. Annual technical report for year ending November 30, 1991

    SciTech Connect (OSTI)

    Aukrust, A.

    1992-01-01

    The Direct Steelmaking Program has completed the third year of research and development since cost-share funding was provided by the Department of Energy. The physical chemistry programs conducted by Carnegie Mellon University (CMU) and the Massachusetts Institute of Technology (MIT) have been completed. A pilot plant has been constructed and successfully operated at Universal, Pennsylvania, and construction of a new, two-zone vessel pilot plant has been completed and trial operation is underway. The success of the pilot plant operation coupled with the development of process models involving reaction rates, heat-transfer and fluid-flow rates, and mass and energy balances has led to a basic study of a 350,000 tonne per year demonstration plant that gives promise of being a low capital and operating cost alternative for ironmaking as compared to the coke oven, blast furnace process. It has the further advantages of ease of startup and shutdown, lower energy consumption, and modularity so that capacity can be adapted to need. The physical chemistry programs at CMU and MIT studied fundamental reactions among ore, coal, flux, slag, metal droplets, and the liquid metal bath. Work at CMU centered on slag foaming studies, coal devolatilization, dissolution of hematite and wustite pellets in bath smelting slags, reduction of FeO in slag by char, extent of reverse or depostcombustion reactions in postcombustion gases, and developing an overall smelting model.

  20. Student Internship Programs Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Student Internship Programs Program Description The objective of the Laboratory's student internship programs is to provide students with opportunities for meaningful hands- on experience supporting educational progress in their selected scientific or professional fields. The most significant impact of these internship experiences is observed in the intellectual growth experienced by the participants. Student interns are able to appreciate the practical value of their education efforts in their

  1. DOE-NE Light Water Reactor Sustainability Program and EPRI Long-Term Operations Program Joint Research and Development Plan

    SciTech Connect (OSTI)

    Don Williams

    2012-04-01

    Nuclear power has contributed almost 20% of the total amount of electricity generated in the United States over the past two decades. High capacity factors and low operating costs make nuclear power plants (NPPs) some of the most economical power generators available. Further, nuclear power remains the single largest contributor (nearly 70%) of non-greenhouse gas-emitting electric power generation in the United States. Even when major refurbishments are performed to extend operating life, these plants continue to represent cost-effective, low-carbon assets to the nation's electrical generation capability.

  2. Fundamentals of Delayed Coking Joint Industry Project

    SciTech Connect (OSTI)

    Michael Volk Jr; Keith Wisecarver

    2005-10-01

    Delayed coking evolved steadily over the early to mid 1900s to enable refiners to convert high boiling, residual petroleum fractions to light products such as gasoline. Pound for pound, coking is the most energy intensive of any operation in a modern refinery. Large amounts of energy are required to heat the thick, poor-quality petroleum residuum to the 900 to 950 degrees F required to crack the heavy hydrocarbon molecules into lighter, more valuable products. One common misconception of delayed coking is that the product coke is a disadvantage. Although coke is a low valued (near zero economic value) byproduct, compared to transportation fuels, there is a significant worldwide trade and demand for coke as it is an economical fuel. Coke production has increased steadily over the last ten years, with further increases forecast for the foreseeable future. Current domestic production is near 111,000 tons per day. A major driving force behind this increase is the steady decline in crude quality available to refiners. Crude slates are expected to grow heavier with higher sulfur contents while environmental restrictions are expected to significantly reduce the demand for high-sulfur residual fuel oil. Light sweet crudes will continue to be available and in even greater demand than they are today. Refiners will be faced with the choice of purchasing light sweet crudes at a premium price, or adding bottom of the barrel upgrading capability, through additional new investments, to reduce the production of high-sulfur residual fuel oil and increase the production of low-sulfur distillate fuels. A second disadvantage is that liquid products from cokers frequently are unstable, i.e., they rapidly form gum and sediments. Because of intermediate investment and operating costs, delayed coking has increased in popularity among refiners worldwide. Based on the 2000 Worldwide Refining Survey published in the Oil and Gas, the delayed coking capacity for 101 refineries around the world is 2,937,439 barrels/calendar day. These cokers produce 154,607 tons of coke per day and delayed coking accounts for 88% of the world capacity. The delayed coking charge capacity in the United States is 1,787,860 b/cd. Despite its wide commercial use, only relatively few contractors and refiners are truly knowledgeable in delayed-coking design, so that this process carries with it a ''black art'' connotation. Until recently, the expected yield from cokers was determined by a simple laboratory test on the feedstock. As a result of Tulsa University's prior related research, a process model was developed that with additional work could be used to optimize existing delayed cokers over a wide range of potential feedstocks and operating conditions. The objectives of this research program are to: utilize the current micro, batch and pilot unit facilities at The University of Tulsa to enhance the understanding of the coking process; conduct additional micro and pilot unit tests with new and in-house resids and recycles to make current optimization models more robust; conduct focused kinetic experiments to enhance the furnace tube model and to enhance liquid production while minimizing sulfur in the products; conduct detailed foaming studies to optimize the process and minimize process upsets; quantify the parameters that affect coke morphology; and to utilize the knowledge gained from the experimental and modeling studies to enhance the computer programs developed in the previous JIP for optimization of the coking process. These refined computer models will then be tested against refinery data provided by the member companies. Novel concepts will also be explored for hydrogen sulfide removal of furnace gases as well as gas injection studies to reduce over-cracking. The following deliverables are scheduled from the two projects of the three-year JIP: (1) A novel method for enhancing liquid yields from delayed cokers and data that provide insight as to the optimum temperature to remove hydrogen sulfide from furnace gases. (2) An understanding of what causes foaming in c

  3. Measurement of joint kinematics using a conventional clinical single-perspective flat-panel radiography system

    SciTech Connect (OSTI)

    Seslija, Petar; Teeter, Matthew G.; Yuan Xunhua; Naudie, Douglas D. R.; Bourne, Robert B.; MacDonald, Steven J.; Peters, Terry M.; Holdsworth, David W.

    2012-10-15

    Purpose: The ability to accurately measure joint kinematics is an important tool in studying both normal joint function and pathologies associated with injury and disease. The purpose of this study is to evaluate the efficacy, accuracy, precision, and clinical safety of measuring 3D joint motion using a conventional flat-panel radiography system prior to its application in an in vivo study. Methods: An automated, image-based tracking algorithm was implemented to measure the three-dimensional pose of a sparse object from a two-dimensional radiographic projection. The algorithm was tested to determine its efficiency and failure rate, defined as the number of image frames where automated tracking failed, or required user intervention. The accuracy and precision of measuring three-dimensional motion were assessed using a robotic controlled, tibiofemoral knee phantom programmed to mimic a subject with a total knee replacement performing a stair ascent activity. Accuracy was assessed by comparing the measurements of the single-plane radiographic tracking technique to those of an optical tracking system, and quantified by the measurement discrepancy between the two systems using the Bland-Altman technique. Precision was assessed through a series of repeated measurements of the tibiofemoral kinematics, and was quantified using the across-trial deviations of the repeated kinematic measurements. The safety of the imaging procedure was assessed by measuring the effective dose of ionizing radiation associated with the x-ray exposures, and analyzing its relative risk to a human subject. Results: The automated tracking algorithm displayed a failure rate of 2% and achieved an average computational throughput of 8 image frames/s. Mean differences between the radiographic and optical measurements for translations and rotations were less than 0.08 mm and 0.07 Degree-Sign in-plane, and 0.24 mm and 0.6 Degree-Sign out-of-plane. The repeatability of kinematics measurements performed using the radiographic tracking technique was better than {+-}0.09 mm and 0.12 Degree-Sign in-plane, and {+-}0.70 mm and {+-}0.07 Degree-Sign out-of-plane. The effective dose associated with the imaging protocol used was 15 {mu}Sv for 10 s of radiographic cine acquisition. Conclusions: This study demonstrates the ability to accurately measure knee-joint kinematics using a single-plane radiographic measurement technique. The measurement technique can be easily implemented at most clinical centers equipped with a modern-day radiographic x-ray system. The dose of ionizing radiation associated with the image acquisition represents a minimal risk to any subjects undergoing the examination.

  4. Thermoacoustic method for relaxation of residual stresses in welded joints

    SciTech Connect (OSTI)

    Koshovyi, V.V.; Pakhn`o, M.I.; Tsykhan, O.I.

    1995-01-01

    We propose a thermoacoustic method for the relaxation of residual stresses in welded joints, present a block diagram of a generator of local thermoacoustic pulses designed for implementation of this method, and describe our experiment aimed at relaxation of residual tensile stresses.

  5. 2nd Annual National Joint Tribal Emergency Management Conference

    Broader source: Energy.gov [DOE]

    Hosted by the Kalispel Indian Tribe, this three-day workshop is a joint collaboration between the National Congress of American Indians, United South and Eastern Tribes, Affiliated Tribes of the Northwest Indians, and more. The event will feature several speaker sessions and networking opportunities.

  6. Radiological approaches in the evaluation of joint disease in children

    SciTech Connect (OSTI)

    Poznanski, A.K.; Conway, J.J.; Shkolnik, A.; Pachman, L.M.

    1987-04-01

    In summary, the newer technologies in radiology have allowed us to visualize more clearly the manifestation of joint disease in children. The presence of small erosions and cartilage damage can be seen much better with magnetic resonance imaging than with any other modality short of arthrography, a much more invasive examination. Joint effusion, although sometimes visualized with conventional radiography, is probably best recognized with ultrasound or magnetic resonance imaging, although it can be detected with computed tomography as well. For the evaluation of avascular necrosis that can be associated with steroid use in joint disease, bone scintigraphy is a simple, sensitive method. Magnetic resonance may be as or more sensitive and gives additional information as well. In the detection of change with time, conventional radiography probably will remain the standard as it is still the simplest, least expensive examination; however, it has many limitations in specific cases. Bone scintigraphy may be of value in selected cases. Although we have still not had enough experience with magnetic resonance imaging to use it as a way of evaluating progress of joint disease, it promises to be the most sensitive radiologic measure of evaluating progress as small anatomical changes can be detected within the cartilage, which cannot be done easily with other means. 27 references.

  7. Danny Lloyd Supply Purchasing Manager & Jlab Small Business Program Manager

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Danny Lloyd Supply Purchasing Manager & Jlab Small Business Program Manager JSA Mentor-Protégé Program Thomas Jefferson National Accelerator Facility Newport, News, Virginia Danny Lloyd Supply Purchasing Manager JLab Small Business Program Manager JSA Mentor-Protégé Program * Jefferson Lab is managed and operated by Jefferson Science Associates, LLC, a joint venture between Southeastern Universities Research Association, Inc., and Computer Sciences Corporation Applied Technologies, LLC,

  8. Ombuds Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ombuds Program Ombuds Program Committed to fair and equitable treatment of all employees, contractors, and persons doing business with the Laboratory. Contact Ombuds Office Appointments (505) 665-2837 Email Helpline (505) 667-9370 Fax (505) 667-3119 Map & Hours Hours: 8:00 a.m. - 5:00 p.m. The Ombuds Office is a safe haven. We provide a resource for people to call first when faced with conflict or disputes. Ombuds program is an independent, neutral, impartial, confidential, and informal

  9. 2011 DOE Hydrogen Program and Vehicle Technologies Office Annual Merit

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Review and Peer Evaluation Meeting | Department of Energy Hydrogen Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting 2011 DOE Hydrogen Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting May 9-13, 2011 Washington, D.C. Monday, May 9, 2011 Joint Plenary Session Plenary Session Poster Presentations Tuesday, May 10, 2010 Oral Presentations Poster Presentions Wednesday, May 11, 2011 Oral Presentations Poster Presentions

  10. Integrated Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Review (IPR) Quarterly Business Review (QBR) Access to Capital Debt Management July 2013 Aug. 2013 Sept. 2013 Oct. 2013 Nov. 2013 Dec. 2013 Jan. 2014 Feb. 2014 March...

  11. Deconvolution Program

    Energy Science and Technology Software Center (OSTI)

    1999-02-18

    The program is suitable for a lot of applications in applied mathematics, experimental physics, signal analytical system and some engineering applications range i.e. deconvolution spectrum, signal analysis and system property analysis etc.

  12. Program Overview

    Broader source: Energy.gov [DOE]

    The culture of the DOE community will be based on standards. Technical standards will formally integrate part of all DOE facility, program and project activities. The DOE will be recognized as a...

  13. Educational Programs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Educational Programs Educational Programs A collaboration between Los Alamos National Laboratory and the University of California at San Diego (UCSD) Jacobs School of Engineering Contact Institute Director Charles Farrar (505) 663-5330 Email UCSD EI Director Michael Todd (858) 534-5951 Professional Staff Assistant Ellie Vigil (505) 667-2818 Email Administrative Assistant Rebecca Duran (505) 665-8899 Email There are two educational components to the Engineering Institute. The Los Alamos Dynamic

  14. Assessment Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear Energy

  15. Program Leadership

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Leadership - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced

  16. Volunteer Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Community » Volunteer Program Volunteer Program Our good neighbor pledge includes active employee engagement in our communities through volunteering. More than 3,000 current and retired Lab employees have logged more than 1.8 million volunteer hours since 2007. August 19, 2015 LANL employee volunteers with Mountain Canine Corps Lab employee Debbi Miller volunteers for the Mountain Canine Corps with her search and rescue dogs. She also volunteers with another search and rescue organization: the

  17. Russian Health Studies Program- Program History

    Broader source: Energy.gov [DOE]

    U.S./Russian cooperation was initiated in 1994 under a bi-national agreement. The work is conducted under the management of the Joint Coordinating Committee for Radiation Effects Research (JCCRER)

  18. Experimental plan for investigating building-earth heat transfer at the Joint Institute for Heavy Ion Research Building

    SciTech Connect (OSTI)

    Childs, K.W.

    1980-11-01

    An experimental plan is presented for investigating heat transfer between below-grade portions of building envelopes and the surrounding soil. Included is a detailing of data to be collected at an earth-sheltered structure (Joint Institute for Heavy Ion Research Building) to be constructed at Oak Ridge National Laboratory. The attributes of the required data collection instrumentation are defined and a program to assure the accuracy of the collected data is discussed. The experimental plan is intended to be used as a guide to selection, installation, and maintenance of instrumentation as well as in data collection and verification.

  19. Joint Solar Silicon GmbH Co KG JSSI | Open Energy Information

    Open Energy Info (EERE)

    Name: Joint Solar Silicon GmbH & Co KG (JSSI) Place: Germany Sector: Solar Product: Joint venture between Degussa and SolarWorld for the production of solar-grade silicon on...

  20. Digital Sofcell Shanghai ShenLi Goeta solid oxide fuel cell joint...

    Open Energy Info (EERE)

    ShenLi Goeta solid oxide fuel cell joint venture Jump to: navigation, search Name: Digital Sofcell - Shanghai ShenLi - Goeta solid oxide fuel cell joint venture Place: China...

  1. DOE Announces Funding for U.S.-India Joint Clean Energy Research...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    for U.S.-India Joint Clean Energy Research and Development Center DOE Announces Funding for U.S.-India Joint Clean Energy Research and Development Center May 16, 2011 - 12:00am ...

  2. JOINT STATEMENT OF THE CO-CHAIRS OF THE NUCLEAR ENERGY AND NUCLEAR...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    JOINT STATEMENT OF THE CO-CHAIRS OF THE NUCLEAR ENERGY AND NUCLEAR SECURITY WORKING GROUP OF THE BILATERAL U.S. - RUSSIA PRESIDENTIAL COMMISSION JOINT STATEMENT OF THE CO-CHAIRS OF ...

  3. File:07-CA-e - BLM-CEC Joint Siting Process.pdf | Open Energy...

    Open Energy Info (EERE)

    07-CA-e - BLM-CEC Joint Siting Process.pdf Jump to: navigation, search File File history File usage Metadata File:07-CA-e - BLM-CEC Joint Siting Process.pdf Size of this preview:...

  4. Student Internship Programs Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for a summer high school student to 75,000 for a Ph.D. student working full-time for a year. Program Coordinator: Scott Robbins Email: srobbins@lanl.gov Phone number: 663-5621...

  5. PP-82-3 The Joint Owners of the Highgate Interconnection Facilities |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 3 The Joint Owners of the Highgate Interconnection Facilities PP-82-3 The Joint Owners of the Highgate Interconnection Facilities Presidential Permit authorizing The Joint Owners of the Highgate Interconnection Facilities to construct, operate, and maintain electric transmission facilities at the U.S. - Canada Border. PDF icon PP-82-3 The Joint Owners of the Highgate Interconnection Facilities More Documents & Publications PP-76 The Vermont Electric Transmission

  6. Application for Presidential Permit OE Docket No. PP-82-4 Joint Owners of

    Energy Savers [EERE]

    the Highgate Project | Department of Energy Joint Owners of the Highgate Project Application for Presidential Permit OE Docket No. PP-82-4 Joint Owners of the Highgate Project Amended application from Vermont Electric Power Company, Inc. (VELCO), operating-and-management agent for the Joint Owners of the Highgate Project requesting to remove certain operating conditions in the Permit that are no longer necessary. PDF icon PP-82-4 Joint Owners Amended App.pdf More Documents & Publications

  7. United States-Japan Joint Nuclear Energy Action Plan | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    An outline on the United States and Japan's joint nuclear energy action plan. PDF icon United States-Japan Joint Nuclear Energy Action Plan More Documents & Publications Fact Sheet: United States-Japan Joint Nuclear Energy Action Plan United States

  8. Transcript of March 4, 2011 Joint Public Meeting | Department of Energy

    Energy Savers [EERE]

    Transcript of March 4, 2011 Joint Public Meeting Transcript of March 4, 2011 Joint Public Meeting Official Transcript of Proceedings - Nuclear Regulatory Commission PDF icon Transcript of March 4, 2011 Joint Public Meeting More Documents & Publications CERTIFICATE OF AUTHENTICITY Office of Information Resources U.S. Offshore Wind Advanced Technology Demonstration Projects Public Meeting Transcript for Offshore Wind Demonstrations

  9. Postdoctoral Program Program Description The Postdoctoral (Postdoc...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Postdoctoral Program Program Description The Postdoctoral (Postdoc) Research program offers the opportunity for appointees to perform research in a robust scientific R&D...

  10. Sintered silver joints via controlled topography of electronic packaging subcomponents

    DOE Patents [OSTI]

    Wereszczak, Andrew A.

    2014-09-02

    Disclosed are sintered silver bonded electronic package subcomponents and methods for making the same. Embodiments of the sintered silver bonded EPSs include topography modification of one or more metal surfaces of semiconductor devices bonded together by the sintered silver joint. The sintered silver bonded EPSs include a first semiconductor device having a first metal surface, the first metal surface having a modified topography that has been chemically etched, grit blasted, uniaxial ground and/or grid sliced connected to a second semiconductor device which may also include a first metal surface with a modified topography, a silver plating layer on the first metal surface of the first semiconductor device and a silver plating layer on the first metal surface of the second semiconductor device and a sintered silver joint between the silver plating layers of the first and second semiconductor devices which bonds the first semiconductor device to the second semiconductor device.

  11. Interlanguage Programming

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Interlanguage Programming Interlanguage Programming This page provides examples of compilation and running scripts when mixing C/C++ with Fortran codes. C/MPI Main Calling Fortran Subroutine Here is a full example of a parallel C code using MPI which calls a Fortran subroutine. The Fortran subroutine sets a number of data values based on the MPI task ID. The code is compiled and run using the batch system. C Source Code % cat cmainmpi.c #include "mpi.h" int main(int argc, char* argv[])

  12. New Report Describes Joint Opportunities for Natural Gas and Hydrogen

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fuel-Cell Vehicle Markets Describes Joint Opportunities for Natural Gas and Hydrogen Fuel-Cell Vehicle Markets - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid

  13. DOE - NNSA/NFO -- News & Views Emergency Joint Exercise

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Emergency Response Personnel Conduct Joint Exercise Photo - Emergancy Response Exercise Approximately 650 people from the Department of Defense and Department of Energy took part in a 1981 weapons accident training exercise, in Area 25 of the Nevada Test Site. The purpose of the exercise was to put into action a planned response to a nuclear accident. The scenario involved a simulated crash of an Army helicopter transporting nuclear weapons to a storage site. The helicopter crashed near the

  14. Joint DOE-MSA News Release Media Contacts:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    March 19, 2015 Joint DOE-MSA News Release Media Contacts: Cameron Hardy, DOE, (509) 376-5365, Cameron.Hardy@rl.doe.gov Rae Weil, Mission Support Alliance, (509) 376-6522, Rae_S_Weil@rl.gov DOE-NNSA, Washington to take part in regional exercise in Benton and Franklin Counties Training designed to enable responders to work together effectively during radiological emergencies Richland, Wash. - The U.S. Department of Energy's (DOE) National Nuclear Security Administration's (NNSA) Radiological

  15. DOE Joint Solid State Lighting Roundtables on Science Challenges

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joint Solid State Lighting Roundtables on Science Challenges Basic Energy Sciences/Energy Efficiency and Renewable Energy October 7, 2014 Washington, D.C. Prepared For: Basic Energy Sciences Office of Science U.S. Department of Energy Prepared By: LED Lighting Advisors Navigant Consulting, Inc. SB Consulting SSLS, Inc. December 8, 2014 i DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government, nor any

  16. Porosity in collapsible Ball Grid Array solder joints

    SciTech Connect (OSTI)

    Gonzalez, C.A. |

    1998-05-01

    Ball Grid Array (BGA) technology has taken off in recent years due to the increased need for high interconnect density. Opposite to all the advantages BGA packages offer, porosity in collapsible BGA solder joints is often a major concern in the reliability of such packages. The effect of pores on the strength of collapsible BGA solder-joints was studied by manufacturing samples with different degrees of porosity and testing them under a shear load. It was found that the shear strength of the solder joints decreased in a linear fashion with increasing porosity. Failure occurred by internal necking of the interpore matrix. It was confirmed that entrapment of flux residues leads to porosity by manufacturing fluxless samples in a specially made furnace, and comparing them with samples assembled using flux. Also, contamination of Au electrodeposits (in substrate metallization) was determined to cause significant porosity. It was found that hard-Au (Co hardened Au) electrodeposits produce high degrees of porosity even in the absence of flux. Finally, increasing the time the solder spends in the molten state was proven to successfully decrease porosity.

  17. Expansion joint for guideway for magnetic levitation transportation system

    DOE Patents [OSTI]

    Rossing, Thomas D. (DeKalb, IL)

    1993-01-01

    An expansion joint that allows a guideway of a magnetic levitation transportation system to expand and contract while minimizing transients occurring in the magnetic lift and drag forces acting on a magnetic levitation vehicle traveling over the joint includes an upper cut or recess extending downwardly from the upper surface of the guideway and a non-intersecting lower cut or recess that extends upwardly from the lower surface of the guideway. The sidewalls of the cuts can be parallel to each other and the vertical axis of the guideway; the depth of the lower cut can be greater than the depth of the upper cut; and the overall combined lengths of the cuts can be greater than the thickness of the guideway from the upper to lower surface so that the cuts will overlap, but be spaced apart from each other. The distance between the cuts can be determined on the basis of the force transients and the mechanical behavior of the guideway. A second pair of similarly configured upper and lower cuts may be disposed in the guideway; the expansion joint may consist of two upper cuts and one lower cut; or the cuts may have non-parallel, diverging sidewalls so that the cuts have a substantially dove-tail shape.

  18. Expansion joint for guideway for magnetic levitation transportation system

    DOE Patents [OSTI]

    Rossing, T.D.

    1993-02-09

    An expansion joint that allows a guideway of a magnetic levitation transportation system to expand and contract while minimizing transients occurring in the magnetic lift and drag forces acting on a magnetic levitation vehicle traveling over the joint includes an upper cut or recess extending downwardly from the upper surface of the guideway and a non-intersecting lower cut or recess that extends upwardly from the lower surface of the guideway. The side walls of the cuts can be parallel to each other and the vertical axis of the guideway; the depth of the lower cut can be greater than the depth of the upper cut; and the overall combined lengths of the cuts can be greater than the thickness of the guideway from the upper to lower surface so that the cuts will overlap, but be spaced apart from each other. The distance between the cuts can be determined on the basis of the force transients and the mechanical behavior of the guideway. A second pair of similarly configured upper and lower cuts may be disposed in the guideway; the expansion joint may consist of two upper cuts and one lower cut; or the cuts may have non-parallel, diverging side walls so that the cuts have a substantially dove-tail shape.

  19. Program Year 2008 State Energy Program Formula

    Broader source: Energy.gov [DOE]

    U.S. Department of Energy (DOE) State Energy Program (SEP), SEP Program Guidance Fiscal Year 2008, Program Year 2008, energy efficiency and renewable energy programs in the states, DOE Office of Energy Efficiency and Renewable Energy

  20. U.S.-Brazil Binational Joint Action Plan | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -Brazil Binational Joint Action Plan U.S.-Brazil Binational Joint Action Plan U.S.-Brazil Binational Energy Working Group, formed on July 20, 2010, when DOE and the Brazilian Ministry of Mines and Energy signed a Joint Action Plan PDF icon brazil_actionplan_7202010.pdf More Documents & Publications US - Brazil Binational Energy Working Group Joint Action Plan U.S.-Brazil Strategic Energy Dialogue Joint Report Summary of the meeting between the the United States of America and the Federative

  1. Final Joint Statement from G-7 Energy Ministers Meeting in Rome |

    Office of Environmental Management (EM)

    Department of Energy Final Joint Statement from G-7 Energy Ministers Meeting in Rome Final Joint Statement from G-7 Energy Ministers Meeting in Rome PDF icon Final Joint Statement from G-7 Energy Ministers Meeting in Rome More Documents & Publications Final Joint Statement from G-7 Energy Ministers Meeting in Rome Before the Senate Committee on Energy and Natural Resources Joint Statement by Energy Ministers of G8, The People's Republic of China, India and The Republic of Korea (June

  2. Advanced Emissions Control Development Program

    SciTech Connect (OSTI)

    A.P.Evans; K.E. Redinger; M.J. Holmes

    1998-04-01

    The objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of air toxics from coal-fired boilers. Ideally, the project aim is to effectively control air toxic emissions through the use of conventional flue gas cleanup equipment such as electrostatic precipitators (ESPS), fabric filters (baghouse), and wet flue gas desulfurization. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate and hydrogen chloride. Following the construction and evaluation of a representative air toxics test facility in Phase I, Phase II focused on the evaluation of mercury and several other air toxics emissions. The AECDP is jointly funded by the United States Department of Energy's Federal Energy Technology Center (DOE), the Ohio Coal Development Office within the Ohio Department of Development (oCDO), and Babcock& Wilcox-a McDermott company (B&W).

  3. IMPACTS: Industrial Technologies Program, Summary of Program...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    77 DOE Industrial Technologies Program Appendix 4: Method of Calculating Results for the IAC Program u IAC Table......

  4. Mechanisms of degradation in adhesive joint strength: Glassy polymer thermoset bond in a humid environment

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kropka, Jamie Michael; Adolf, Douglas Brian; Spangler, Scott Wilmer; Austin, Kevin N.; Chambers, Robert S.

    2015-08-06

    The degradation in the strength of napkin-ring (NR) joints bonded with an epoxy thermoset is evaluated in a humid environment. While adherend composition (stainless steel and aluminum) and surface preparation (polished, grit blasted, primed, coupling agent coated) do not affect virgin (time=0) joint strength, they can significantly affect the role of moisture on the strength of the joint. Adherend surface abrasion and corrosion processes are found to be key factors in determining the reliability of joint strength in humid environments. In cases where surface specific joint strength degradation processes are not active, decreases in joint strength can be accounted formore » by the glass transition temperature, Tg, depression of the adhesive associated with water sorption. Under these conditions, joint strength can be rejuvenated to virgin strength by drying. In addition, the decrease in joint strength associated with water sorption can be predicted by the Simplified Potential Energy Clock (SPEC) model by shifting the adhesive reference temperature, Tref, by the same amount as the Tg depression. When surface specific degradation mechanisms are active, they can reduce joint strength below that associated with adhesive Tg depression, and joint strength is not recoverable by drying. Furthermore, a critical relative humidity (or, potentially, critical water sorption concentration), below which the surface specific degradation does not occur, appears to exist for the polished stainless steel joints.« less

  5. Mechanisms of degradation in adhesive joint strength: Glassy polymer thermoset bond in a humid environment

    SciTech Connect (OSTI)

    Kropka, Jamie Michael; Adolf, Douglas Brian; Spangler, Scott Wilmer; Austin, Kevin N.; Chambers, Robert S.

    2015-08-06

    The degradation in the strength of napkin-ring (NR) joints bonded with an epoxy thermoset is evaluated in a humid environment. While adherend composition (stainless steel and aluminum) and surface preparation (polished, grit blasted, primed, coupling agent coated) do not affect virgin (time=0) joint strength, they can significantly affect the role of moisture on the strength of the joint. Adherend surface abrasion and corrosion processes are found to be key factors in determining the reliability of joint strength in humid environments. In cases where surface specific joint strength degradation processes are not active, decreases in joint strength can be accounted for by the glass transition temperature, Tg, depression of the adhesive associated with water sorption. Under these conditions, joint strength can be rejuvenated to virgin strength by drying. In addition, the decrease in joint strength associated with water sorption can be predicted by the Simplified Potential Energy Clock (SPEC) model by shifting the adhesive reference temperature, Tref, by the same amount as the Tg depression. When surface specific degradation mechanisms are active, they can reduce joint strength below that associated with adhesive Tg depression, and joint strength is not recoverable by drying. Furthermore, a critical relative humidity (or, potentially, critical water sorption concentration), below which the surface specific degradation does not occur, appears to exist for the polished stainless steel joints.

  6. Mechanisms of degradation in adhesive joint strength: Glassy thermoset polymer bond in a humid environment

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kropka, Jamie Michael; Adolf, Douglas Brian; Spangler, Scott Wilmer; Austin, Kevin N.; Chambers, Robert S.

    2015-08-06

    The degradation in the strength of napkin-ring (NR) joints bonded with an epoxy thermoset is evaluated in a humid environment. While adherend composition (stainless steel and aluminum) and surface preparation (polished, grit blasted, primed, coupling agent coated) do not affect virgin (time=0) joint strength, they can significantly affect the role of moisture on the strength of the joint. Adherend surface abrasion and corrosion processes are found to be key factors in determining the reliability of joint strength in humid environments. In cases where surface specific joint strength degradation processes are not active, decreases in joint strength can be accounted formoreby the glass transition temperature, Tg, depression of the adhesive associated with water sorption. Under these conditions, joint strength can be rejuvenated to virgin strength by drying. In addition, the decrease in joint strength associated with water sorption can be predicted by the Simplified Potential Energy Clock (SPEC) model by shifting the adhesive reference temperature, Tref, by the same amount as the Tg depression. When surface specific degradation mechanisms are active, they can reduce joint strength below that associated with adhesive Tg depression, and joint strength is not recoverable by drying. Furthermore, a critical relative humidity (or, potentially, critical water sorption concentration), below which the surface specific degradation does not occur, appears to exist for the polished stainless steel joints.less

  7. Solder Joints of Power Electronics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    09 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. PDF icon pmp_06_govindarajan

  8. Oil shale, tar sand, coal research, advanced exploratory process technology, jointly sponsored research

    SciTech Connect (OSTI)

    Not Available

    1992-01-01

    Progress made in five research programs is described. The subtasks in oil shale study include oil shale process studies and unconventional applications and markets for western oil shale.The tar sand study is on recycle oil pyrolysis and extraction (ROPE) process. Four tasks are described in coal research: underground coal gasification; coal combustion; integrated coal processing concepts; and sold waste management. Advanced exploratory process technology includes: advanced process concepts; advanced mitigation concepts; and oil and gas technology. Jointly sponsored research covers: organic and inorganic hazardous waste stabilization; CROW field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; PGI demonstration project; operation and evaluation of the CO[sub 2] HUFF-N-PUFF process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesaverde group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; shallow oil production using horizontal wells with enhanced oil recovery techniques; NMR analysis of sample from the ocean drilling program; and menu driven access to the WDEQ hydrologic data management system.

  9. University/NETL Student Partnership Program

    SciTech Connect (OSTI)

    Gerald Holder; Jonathan Mathews; Thomas Wilson; Steven Chuang; Cristina Amon; Turgay Ertekin; Karl Johnson; Goodarz Ahmadi; David Sholl

    2006-10-31

    The University/National Energy Technology Laboratory (NETL) Student Partnership Program stimulated basic and applied research in Energy and Environmental Science areas through NETL's Office of Science and Technology (OST). This Partnership Program supported the education of graduate students in Energy and Environmental Sciences, while fostering increased scientific interaction between NETL and the participating universities, by providing graduate student support for research at a NETL facility under the joint supervision of NETL and university faculty. Projects were intended to enhance a previously established scientific or engineering relationship or to create a new relationship. Major areas of research under the Partnership Program included CO{sub 2} sequestration, granular solids flow, multi-phase flow in porous solids, gas hydrates, nanotubes, acid-mine flow identification and remediation, water-gas shift reaction, circulating fluidized beds, slurry bubble column, fuel desulphurization, carbon fibers, and fuel cells.

  10. Program Development

    SciTech Connect (OSTI)

    Atencio, Julian J.

    2014-05-01

    This presentation covers how to go about developing a human reliability program. In particular, it touches on conceptual thinking, raising awareness in an organization, the actions that go into developing a plan. It emphasizes evaluating all positions, eliminating positions from the pool due to mitigating factors, and keeping the process transparent. It lists components of the process and objectives in process development. It also touches on the role of leadership and the necessity for audit.

  11. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Description Discover E (Engineering) is an evening of interesting, interactive and fun engineering, science, math, and technology demonstrations for K-12 students and their parents or guardians. It is held in conjunction with National Engineers Week which is celebrated at the time of George Washington's birthday, our nation's first President, who was a military engineer and land surveyor. Activities include 30-50 interactive demonstrations of basic engineering, science, technology and

  12. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MATHCOUNTS is a national enrichment, coaching and competition program that promotes middle school mathematic achievement. The mission of MATHCOUNTS is to increase enthusiasm for and enhance achievement in middle school mathematics throughout the United States. MATHCOUNTS is supported by the National Society of Professional Engineers (NSPE), The National Council of Teachers of Mathematics and the National Aeronautics and Space Administration, to name a few. . With the generous support of all

  13. Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    bowl Program Description The Science Bowl® is a nationwide academic competition that tests students' knowledge in all areas of science and mathematics. Middle and high school student teams from diverse backgrounds are comprised of four students, one alternate, and a teacher who serves as an advisor and coach. These teams face-off in a fast-paced question-and-answer format, being tested on a range of science disciplines including biology, chemistry, Earth science, physics, energy, and math. The

  14. Quality Program

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    QP001 Revision 0 Effective October 15, 2001 QUALITY PROGRAM Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Jude M. Clark Approved by: _______________________________________________ Date: ______________ Donald B. Karner Procedure ETA-QP001 Revision 0 2 2001 Electric Transportation Applications All Rights Reserved TABLE OF CONTENTS 1.0 Objectives 3 2.0 Scope 3 3.0 Documentation 3 4.0 Prerequisites 4 5.0 Exclusions 5 6.0 Quality

  15. Environmental Programs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Los Alamos National Laboratory | Environmental Programs Material Disposal Areas and the Threat of Wildfire Fact Sheet Established in 1943, Los Alamos National Laboratory now consists of 1,280 buildings in 47 technical areas spread out over 37 square miles. The complex includes 11 nuclear facilities and more than 10,000 workers. Los Alamos and Wildfires In the past, large wildfires in the area, including the La Mesa Fire (1977), the Dome Fire (1996), the Oso Fire (1998), the Cerro Grande Fire

  16. Environmental Programs

    Office of Environmental Management (EM)

    Alamos National Laboratory | Environmental Programs Material Disposal Areas and the Threat of Wildfire Fact Sheet Established in 1943, Los Alamos National Laboratory now consists of 1,280 buildings in 47 technical areas spread out over 37 square miles. The complex includes 11 nuclear facilities and more than 10,000 workers. Los Alamos and Wildfires In the past, large wildfires in the area, including the La Mesa Fire (1977), the Dome Fire (1996), the Oso Fire (1998), the Cerro Grande Fire (2000)

  17. STEP Program Benchmark Report

    Broader source: Energy.gov [DOE]

    STEP Program Benchmark Report, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  18. Residential Buildings Integration Program

    Broader source: Energy.gov [DOE]

    Residential Buildings Integration Program Presentation for the 2013 Building Technologies Office's Program Peer Review

  19. Maryland Efficiency Program Options

    Broader source: Energy.gov [DOE]

    Maryland Efficiency Program Options, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  20. Transcript of March 4, 2011 Joint Public Meeting

    Office of Environmental Management (EM)

    Official Transcript of Proceedings NUCLEAR REGULATORY COMMISSION Title: Disposal of Low-Level Nuclear Waste Joint NRC/DOE Workshop Docket Number: (n/a) Location: Phoenix, Arizona Date: Friday, March 4, 2011 Work Order No.: NRC-753 Pages 1-267 NEAL R. GROSS AND CO., INC. Court Reporters and Transcribers 1323 Rhode Island Avenue, N.W. Washington, D.C. 20005 (202) 234-4433 NEAL R. GROSS COURT REPORTERS AND TRANSCRIBERS 1323 RHODE ISLAND AVE., N.W. (202) 234-4433 WASHINGTON, D.C. 20005-3701

  1. United States -Japan Joint Nuclear Energy Action Plan

    Broader source: Energy.gov (indexed) [DOE]

    -Japan Joint Nuclear Energy Action Plan 1. Introduction 1.1 Background and Objective President Bush of the U n i t e d States and Prime Minister Koizumi of Japan have both stated their strong support for the contribution of nuclear power to energy security and the global environment. Japan w a s the first nation to endorse President Bush's Global Nuclear Energy Partnership. During the June 29,2006 meeting between President Bush and Prime Minister Koizumi, "We discussed research and

  2. WTP Safety Culture Advice Joint Topic (HSEP/TWC)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    January 2012 v1 Page 1 of 2 Note: The views expressed in committee meetings should not be considered a substitute for full HAB consensus on any particular issue. WTP Safety Culture Advice Joint Topic (HSEP/TWC) Framing questions for discussion regarding DOE's recently released Implementation Plan: Re: Secretary Chu's response to the DNFSB with the Implementation Plan for Recommendation 2011-1 (December 27, 2011) Note: The ORP coordinator for the DOE Response to DNFSB 2011-1 is Steve Pfaff. o

  3. Joint DOE-MSA News Release Media Contacts:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    October 22, 2014 Joint DOE-MSA News Release Media Contacts: Cameron Hardy, DOE, (509) 376-5365, Cameron.Hardy@rl.doe.gov Rae Weil, Mission Support Alliance, (509) 376-6522, Rae_S_Weil@rl.gov Workers Enter Cocooned F Reactor for Scheduled Inspection Inspection by DOE ensures reactors are safe, secure RICHLAND, Wash. - Workers from Mission Support Alliance, LLC., removed the welds around the steel door of the F Reactor last week before stepping inside the reactor to complete its periodic

  4. Joint Facilities User Forum on Data Intensive Computing Lessons Learned

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    User Forum on Data Intensive Computing Lessons Learned - NERSC/JGI Partnership Kjiersten Fagnan, NERSC User Services/JGI --- 1 --- June 1 7, 2 013 Outline * Overview o f N ERSC/JGI P artnership - DOE J GI b ackground - Team o verview - Compute r esources * CompuBng S trategic P lan - JGI G oals - NERSC G oals * Lessons Learned --- 2 --- DOE Joint Genome Institute 3 DOE JGI, Serving as a genomic user facility in support of the DOE missions: * Walnut Creek, CA facility opened in 1999 * 250

  5. EA-2006: Columbia Estuary Ecosystem Restoration Program

    Broader source: Energy.gov [DOE]

    Bonneville Power Administration and the U.S. Army Corps of Engineers are jointly preparing a programmatic EA for actions recommended by the Northwest Power and Conservation Council to help restore ecological structure, function, and biodiversity within the Columbia River estuary. Activities under this program could include full reconnection of tidal influence through breaching dikes and levees; partial reconnection of tidal influence through culverts, bridges, and tidegates; enhancement of the quantity and quality of tidal channels; removal of invasive species; and restoration of riparian habitat conditions, such as planting native vegetation.

  6. Intergovernmental Programs | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs Intergovernmental Programs The Office of Environmental Management supports, by means of grants and cooperative agreements, a number of

  7. Programming Libraries

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Math Libraries Programming Tools List Performance and Debugging Tools Grid Software and Services NERSC Software Downloads Policies User Surveys NERSC Users Group User Announcements Help Staff Blogs Request Repository Mailing List Operations for: Passwords & Off-Hours Status 1-800-66-NERSC, option 1 or 510-486-6821 Account Support https://nim.nersc.gov accounts@nersc.gov 1-800-66-NERSC, option 2 or 510-486-8612 Consulting http://help.nersc.gov consult@nersc.gov 1-800-66-NERSC, option 3 or

  8. Program Update

    Energy Savers [EERE]

    April-June 2014 issue of the U.S. Department of Energy (DOE) Offce of Legacy Management (LM) Program Update. This publication is designed to provide a status of activities within LM. Please direct all comments and inquiries to lm@hq.doe.gov. April-June 2014 Visit us at http://energy.gov/lm/ Goal 4 Optimizing the Use of Federal Lands Through Disposition The foundation of the U.S. Department of Energy (DOE) Offce of Legacy Manage- ment's (LM) Goal 4, "Optimize the use of land and

  9. stockpile stewardship program

    National Nuclear Security Administration (NNSA)

    NIF, in particular the first Pu experiment on NIF, the return to operations of the TA-55 gas gun, a successful series of plutonium experiments on Joint Actinide Shock Physics...

  10. Independent wheel suspension system using constant velocity universal joints in combination with a single prop shaft joint and mounted differentials

    SciTech Connect (OSTI)

    Krude, W.

    1986-06-24

    An independent wheel suspension system is described for a vehicle having a chassis, vehicle support means for resiliently supporting the chassis for displacement with respect to a driving surface, a wheel assembly with a wheel rotatable about a wheel axis, and an engine adapted to provide driving torque about an engine output axis at an engine output, the independent wheel suspension system consists of: control arm means having a wheel end pivotably connected to the wheel assembly and a pair of frame ends pivotably connected to a respective pair of pivot bearings carried by the vehicle support means to define a swing axis therethrough; differential means comprising a differential housing, differential input means and differential output means within the differential housing establishing a respective differential input axis and a differential output axis substantially perpendicular thereto; transverse pivot means coupling the differential means and the vehicle support means for allowing the differential means to pivot relative to the vehicle support means about a transverse pivot axis substantially parallel to the differential output axis; and prop shaft means having a prop shaft axis and first and second prop shaft coupling means coupling, respectively, to the engine output and the differential input, the first prop shaft coupling means being a constant velocity universal joint, the second prop shaft coupling means being one of an axially splined joint or a fixed joint; whereby, as the first prop shaft coupling means undergoes articulation with respect to the prop shaft means as the chassis undergoes the displacement, the transverse pivot means allows the differential means to pivot relative to the vehicle support means about the transverse pivot axis to accommodate the articulation without articulation between the differential means and the prop shaft means.

  11. Performance of bolted closure joint elastomers under cask aging conditions

    SciTech Connect (OSTI)

    Verst, C.; Sindelar, R.; Skidmore, E.; Daugherty, W.

    2015-07-23

    The bolted closure joint of a bare spent fuel cask is susceptible to age-related degradation and potential loss of confinement function under long-term storage conditions. Elastomeric seals, a component of the joint typically used to facilitate leak testing of the primary seal that includes the metallic seal and bolting, is susceptible to degradation over time by several mechanisms, principally via thermo-oxidation, stress-relaxation, and radiolytic degradation under time and temperature condition. Irradiation and thermal exposure testing and evaluation of an ethylene-propylene diene monomer (EPDM) elastomeric seal material similar to that used in the CASTOR® V/21 cask for a matrix of temperature and radiation exposure conditions relevant to the cask extended storage conditions, and development of semiempirical predictive models for loss of sealing force is in progress. A special insert was developed to allow Compressive Stress Relaxation (CSR) measurements before and after the irradiation and/or thermal exposure without unloading the elastomer. A condition of the loss of sealing force for the onset of leakage was suggested. The experimentation and modeling being performed could enable acquisition of extensive coupled aging data as well as an estimation of the timeframe when loss of sealing function under aging (temperature/radiation) conditions may occur.

  12. Biomass Program 2007 Program Peer Review - Program Summary Section

    SciTech Connect (OSTI)

    none,

    2009-10-27

    This document summarizes the comments provided by the peer reviewers at the U.S. Department of Energy (DOE) Biomass Programs Peer Review meeting, held on November 14-15, 2007 in Baltimore, MD and Platform Reviews conducted over the summer of 2007. The Platform Reviews provide evaluations of the Programs projects in applied research, development, and demonstration.

  13. Geothermal Technologies Program Overview - Peer Review Program

    SciTech Connect (OSTI)

    Milliken, JoAnn

    2011-06-06

    This Geothermal Technologies Program presentation was delivered on June 6, 2011 at a Program Peer Review meeting. It contains annual budget, Recovery Act, funding opportunities, upcoming program activities, and more.

  14. Beryllium Program - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program About Us About Hanford Cleanup Hanford History Hanford Site Wide Programs Beryllium Program Beryllium Program Points of Contact Beryllium Facilities & Areas Beryllium Program Information Hanford CBDPP Committee Beryllium FAQs Beryllium Related Links Hanford Beryllium Awareness Group (BAG) Program Performance Assessments Beryllium Program Feedback Beryllium Health Advocates Primary Contractors/Employers Medical Testing and Surveillance Facilities General Resources Contact Us Beryllium

  15. International DSM and DSM program evaluation: An INDEEP assessment

    SciTech Connect (OSTI)

    Vine, E.

    1995-04-01

    This paper discusses the current level of demand-side management (DSM) occurring in selected European countries and reviews the availability of information on DSM programs and program evaluation. Next, thirteen European DSM programs are compared by examining such factors as: motivations for program implementation, marketing methods, participation rates, total energy savings, and program costs. The transfer of DSM program results and experiences found in these case studies is also discussed, as well as the lessons learned during the design, implementation, and evaluation of these programs. This paper represents a preliminary assessment of the state of DSM and DSM program evaluation in Europe. The findings from this work also represent the first steps in a joint international effort to compile and analyze the measured results of energy efficiency programs in a consistent and comprehensive fashion. The authors find that these programs represent cost-effective resources: the cost of energy saved by the programs ranged from a low of 0.0005 ECUs/kWh (0.01 {cents}/kWh) to a high of 0.077 ECUs/kWh (9.7 {cents}/kWh), with an average cost of 0.027 ECUs/kWh (3.3 {cents}/kWh). Weighted by energy savings, the average cost of energy saved by the programs was 0.014 ECUs/kWh (1.8 {cents}/kWh).

  16. TRU Waste Management Program. Cost/schedule optimization analysis

    SciTech Connect (OSTI)

    Detamore, J.A.; Raudenbush, M.H.; Wolaver, R.W.; Hastings, G.A.

    1985-10-01

    This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office Rockwell International (JIO/RI) during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance development, task monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of reports for DOE detailing program status. Program Analysis is performed by the JIO/RI to support identification and assessment of alternatives, and development of long-term TRU waste program capabilities. These analyses include short-term analyses in response to DOE information requests, along with performing an RH Cost/Schedule Optimization report. Systems models will be developed, updated, and upgraded as needed to enhance JIO/RI's capability to evaluate the adequacy of program efforts in various fields. A TRU program data base will be maintained and updated to provide DOE with timely responses to inventory related questions.

  17. Clean Coal Technology Programs: Program Update 2007

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FE-0514 Clean Coal Technology Programs: Program Update 2007 Includes Clean Coal Technology Demonstration Program (CCTDP), Power Plant Improvement Initiative (PPII), and Clean Coal Power Initiative (CCPI) Projects As of September 2007 U.S. Department of Energy Assistant Secretary for Fossil Energy Washington, DC 20585 January 2008 T E C H N O L O G Y DOE/FE-0514 Clean Coal Technology Programs: Program Update 2007 Includes Clean Coal Technology Demonstration Program (CCTDP), Power Plant

  18. Second National Report for the Joint Convention on the Safety of Spent Fuel

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Management and on the Safety of Radioactive Waste Management | Department of Energy Second National Report for the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management Second National Report for the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management This second National Report updates the first National Report published on May 3, 2003, under the terms of the Joint Convention on the

  19. Joint Maintenance Status Report of Potomac Electric Power Company amd PJM

    Energy Savers [EERE]

    Interconnection, LLC | Department of Energy Joint Maintenance Status Report of Potomac Electric Power Company amd PJM Interconnection, LLC Joint Maintenance Status Report of Potomac Electric Power Company amd PJM Interconnection, LLC Docket No. EO-05-01: Potomac Electric Power Company ("Pepco") and PJM Interconnection, L.L.C. ("PJM") hereby jointly submit this Maintenance Report to advise you of the work completed and findings made during the maintenance outages for

  20. Fourth National Report for the Joint Convention on the Safety of Spent Fuel

    Broader source: Energy.gov (indexed) [DOE]

    Management and on the Safety of Radioactive Waste Management | Department of Energy This Fourth United States of America (U.S.) National Report updates the Third Report published in October 2008, under the terms of the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management (Joint Convention). This report reflects developments in the U.S. through June 2011. This report satisfies the requirements of the Joint Convention for reporting on the

  1. National Report Joint Convention on the Safety of Spent Fuel Management and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    on the Safety of Radioactive Waste Management | Department of Energy National Report Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management National Report Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management This is the first National Report prepared under the terms of the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Managementi hereafter

  2. Third National Report for the Joint Convention on the Safety of Spent Fuel

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Management and on the Safety of Radioactive Waste Management | Department of Energy Third National Report for the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management Third National Report for the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management This Third United States National Report updates the second National Report published in October 2005, under the terms of the Joint

  3. United States-Russia Joint Statement on the Results of the Nuclear Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Nuclear Security Working Group Meeting | Department of Energy States-Russia Joint Statement on the Results of the Nuclear Energy and Nuclear Security Working Group Meeting United States-Russia Joint Statement on the Results of the Nuclear Energy and Nuclear Security Working Group Meeting December 10, 2010 - 12:00am Addthis Moscow - Earlier this week, Deputy Secretary of Energy Daniel Poneman, representing the United States government, signed a joint statement with Russia's Director

  4. United States and France Sign Joint Statement on Civil Liability for

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Nuclear Damage | Department of Energy and France Sign Joint Statement on Civil Liability for Nuclear Damage United States and France Sign Joint Statement on Civil Liability for Nuclear Damage PDF icon Joint Statement Signed.pdf More Documents & Publications Open Government Plan 1.0 Fiscal Year 2010 Agency Financial Report Secretary Chu's Remarks to the 2011 IAEA General Conference (As Prepared for Delivery)

  5. EA-1945: Northern Mid-Columbia Joint Project; Grant, Douglas, and Chelan

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Counties, Washington | Department of Energy EA-1945: Northern Mid-Columbia Joint Project; Grant, Douglas, and Chelan Counties, Washington EA-1945: Northern Mid-Columbia Joint Project; Grant, Douglas, and Chelan Counties, Washington SUMMARY Bonneville Power Administration (BPA) is preparing an EA to assess the potential environmental impacts of the Northern Mid-Columbia Joint Project, a 230-kilvolt transmission line proposed by BPA and the Public Utility Districts of Grant, Chelan, and

  6. Wave Propagation in Jointed Geologic Media (Technical Report) | SciTech

    Office of Scientific and Technical Information (OSTI)

    Connect Wave Propagation in Jointed Geologic Media Citation Details In-Document Search Title: Wave Propagation in Jointed Geologic Media Predictive modeling capabilities for wave propagation in a jointed geologic media remain a modern day scientific frontier. In part this is due to a lack of comprehensive understanding of the complex physical processes associated with the transient response of geologic material, and in part it is due to numerical challenges that prohibit accurate

  7. Application for Presidential Permit OE Docket No. PP-82-4 The Joint Owners

    Energy Savers [EERE]

    of the Highgate Project: Federal Register Notice, Volume 80, No. 241 - December 16, 2015 | Department of Energy The Joint Owners of the Highgate Project: Federal Register Notice, Volume 80, No. 241 - December 16, 2015 Application for Presidential Permit OE Docket No. PP-82-4 The Joint Owners of the Highgate Project: Federal Register Notice, Volume 80, No. 241 - December 16, 2015 Amended application from Vermont Electric Power Company, Inc. as agent for the Joint Owners of the Highgate

  8. Machinist Pipeline/Apprentice Program Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    cost effective than previous time-based programs Moves apprentices to journeyworker status more quickly Program Coordinator: Heidi Hahn Email: hahn@lanl.gov Phone number:...

  9. Existing Facilities Rebate Program

    Broader source: Energy.gov [DOE]

    The NYSERDA Existing Facilities program merges the former Peak Load Reduction and Enhanced Commercial and Industrial Performance programs. The new program offers a broad array of different...

  10. Graduate Research Assistant Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in intellectual vitality and opportunities for growth. Contact Program Manager Scott Robbins Student Programs (505) 667-3639 Email Program Coordinator Emily Robinson Student...

  11. Undergraduate Student Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    while they are pursuing an undergraduate degree. Contact Program Manager Scott Robbins Student Programs (505) 667-3639 Email Program Coordinator Emily Robinson Student...

  12. Exit chimney joint and method of forming the joint for closed circuit steam cooled gas turbine nozzles

    DOE Patents [OSTI]

    Burdgick, Steven Sebastian (Schenectady, NY); Burns, James Lee (Schenectady, NY)

    2002-01-01

    A nozzle segment for a gas turbine includes inner and outer band portions and a vane extending between the band portions. The inner and outer band portions are each divided into first and second plenums separated by an impingement plate. Cooling steam is supplied to the first cavity for flow through the apertures to cool the outer nozzle wall. The steam flows through a leading edge cavity in the vane into the first cavity of the inner band portion for flow through apertures of the impingement plate to cool the inner nozzle wall. Spent cooling steam flows through a plurality of cavities in the vane, exiting through an exit chimney in the outer band. The exit chimney is secured at its inner end directly to the nozzle vane wall surrounding the exit cavities, to the margin of the impingement plate at a location intermediate the ends of the exit chimney and to margins of an opening through the cover whereby each joint is externally accessible for joint formation and for subsequent inspection.

  13. Modular multimorphic kinematic arm structure and pitch and yaw joint for same

    DOE Patents [OSTI]

    Martin, H. Lee (Knoxville, TN); Williams, Daniel M. (Oliver Springs, TN); Holt, W. Eugene (Knoxville, TN)

    1989-01-01

    A multimorphic kinematic manipulator arm is provided with seven degrees of freedom and modular kinematic redundancy through identical pitch/yaw, shoulder, elbow and wrist joints and a wrist roll device at the wrist joint, which further provides to the manipulator arm an obstacle avoidance capability. The modular pitch/yaw joints are traction drive devices which provide backlash free operation with smooth torque transmission and enhanced rigidity. A dual input drive arrangement is provided for each joint resulting in a reduction of the load required to be assumed by each drive and providing selective pitch and yaw motions by control of the relative rotational directions of the input drive.

  14. OMB and CEQ Joint Memorandum on Environmental Collaboration and Conflict Resolution (CEQ, 2012)

    Broader source: Energy.gov [DOE]

    This Office of Management and Budget (OMB) and Council on Environmental Quality (CEQ) joint memorandum expands and builds on the November 28, 2005, Environmental Conflict Resolution (ECR)...

  15. NREL and CSEM Jointly Set New Efficiency Record with Dual-Junction...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL and CSEM Jointly Set New Efficiency Record with Dual-Junction Solar Cell January 5, 2016 Scientists at the Energy Department's National Renewable Energy Laboratory (NREL) and...

  16. Sandia Energy - Joint Sandia-DOE-HMRC Testing of a Floating Oscillatin...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oscillating Water Column Wave Energy Converter Device Home Renewable Energy Energy Water Power Partnership News News & Events Joint Sandia-DOE-HMRC Testing of a Floating...

  17. EPRI-DOE Joint Report on Fossil Fleet Transition with Fuel Changes...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Large Scale Variable Renewable Integration Now Available EPRI-DOE Joint Report on Fossil Fleet Transition with Fuel Changes and Large Scale Variable Renewable Integration ...

  18. EPRI-DOE Joint Report Focuses on Fossil Fleet Transition with...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Changes and Large Scale Variable Renewable Integration EPRI-DOE Joint Report Focuses on Fossil Fleet Transition with Fuel Changes and Large Scale Variable Renewable Integration ...

  19. Time-lapse Joint Inversion of Geophysical Data and its Applications to Geothermal Prospecting

    Broader source: Energy.gov [DOE]

    Time-lapse Joint Inversion of Geophysical Data and its Applications to Geothermal Prospecting presentation at the April 2013 peer review meeting held in Denver, Colorado.

  20. Joint DOE/NRCan Study of North American Transportation Energy Futures: Phase 2 Results

    SciTech Connect (OSTI)

    None

    2009-01-18

    Joint DOE/NRCan Study of North American Transportation Energy Futures: Discussion of the Study, Presentation of Phase 2 Results - April 30, 2003

  1. Activities implemented jointly: First report to the Secretariat of the United Nations Framework Convention on Climate Change. Accomplishments and descriptions of projects accepted under the U.S. Initiative on Joint Implementation

    SciTech Connect (OSTI)

    1996-07-01

    More than 150 countries are now Party to the United Nations Framework Convention on Climate Change (FCCC), which seeks, as its ultimate objective, to stabilize atmospheric concentrations of greenhouse gases at a level that would prevent dangerous human interference with the climate system. As a step toward this goal, all Parties are to take measures to mitigate climate change and to promote and cooperate in the development and diffusion of technologies and practices that control or reduce emissions and enhance sinks of greenhouse gases. In the US view, efforts between countries or entities within them to reduce net greenhouse gas emissions undertaken cooperatively--called joint implementation (JI)--holds significant potential both for combating the threat of global warming and for promoting sustainable development. To develop and operationalize the JI concept, the US launched its Initiative on Joint Implementation (USIJI) in October 1993, and designed the program to attract private sector resources and to encourage the diffusion of innovative technologies to mitigate climate change. The USIJI provides a mechanism for investments by US entities in projects to reduce greenhouse gas emissions worldwide and has developed a set of criteria for evaluating proposed projects for their potential to reduce net GHG emissions.

  2. Better Buildings Neighborhood Program Business Models Guide: Program Administrator Description

    Broader source: Energy.gov [DOE]

    Better Buildings Neighborhood Program Business Models Guide: Program Administrator Business Models, Program Administrator Description.

  3. Vehicle Technologies Program Overview

    SciTech Connect (OSTI)

    none,

    2006-09-05

    Overview of the Vehicle Technologies Program including external assessment and market view; internal assessment, program history and progress; program justification and federal role; program vision, mission, approach, strategic goals, outputs, and outcomes; and performance goals.

  4. Human Reliability Program Overview

    SciTech Connect (OSTI)

    Bodin, Michael

    2012-09-25

    This presentation covers the high points of the Human Reliability Program, including certification/decertification, critical positions, due process, organizational structure, program components, personnel security, an overview of the US DOE reliability program, retirees and academia, and security program integration.

  5. Joint EM-NE-International Study of Glass Behavior over Geologic Time Scales

    SciTech Connect (OSTI)

    Ryan, Joseph V.; Ebert, W. L.; Icenhower, Jonathan P.; Schreiber, Daniel K.; Strachan, Denis M.; Vienna, John D.

    2012-03-30

    Vitrification has been chosen as the best demonstrated available technology for waste immobilization worldwide. To date, the contributions of physical and chemical processes controlling the long-term glass dissolution rate in geologic disposal remain uncertain; leading to a lack of international consensus on a glass corrosion rate law. Existing rate laws have overcome the uncertainty through conservatism, but a thorough mechanistic understanding of waste form durability in geologic environments would improve public and regulator confidence, as well as lead to cost savings if it is possible to take credit for the true durability of the waste form itself in system evaluations. To this end, six nations have joined together to formulate a joint plan for collaborative research into the mechanisms controlling the long-term corrosion of glass. This report highlights the technical program plan behind the US portion of this effort, with an emphasis on the current understanding (and limitations) of several mechanistic theories for glass corrosion. Some recent results are presented to provide an example of the ongoing research.

  6. Joint Urban 2003: Study Overview And Instrument Locations

    SciTech Connect (OSTI)

    Allwine, K Jerry; Flaherty, Julia E.

    2006-08-16

    Quality-assured meteorological and tracer data sets are vital for establishing confidence that indoor and outdoor dispersion models used to simulate dispersal of potential toxic agents in urban atmospheres are giving trustworthy results. The U.S. Department of Defense-Defense Threat Reduction Agency and the U.S. Department of Homeland Security joined together to conduct the Joint Urban 2003 atmospheric dispersion study to provide this critically-needed high-resolution dispersion data. This major urban study was conducted from June 28 through July 31, 2003, in Oklahoma City, Oklahoma, with the participation of over 150 scientists and engineers from over 20 U.S. and foreign institutions. The Joint Urban 2003 lead scientist was Jerry Allwine (Pacific Northwest National Laboratory) who oversaw study design, logistical arrangements and field operations with the help of Joe Shinn (Lawrence Livermore National Laboratory), Marty Leach (Lawrence Livermore National Laboratory), Ray Hosker (Atmospheric Turbulence and Diffusion Division), Leo Stockham (Northrop Grumman Information Technology) and Jim Bowers (Dugway Proving Grounds). This report gives a brief overview of the field campaign, describing the scientific objectives, the dates of the intensive observation periods, and the instruments deployed. The data from this field study is available to the scientific community through an on-line database that is managed by Dugway Proving Ground. This report will be included in the database to provide its users with some general information about the field study, and specific information about the instrument coordinates. Appendix A of this document provides the definitive record of the instrument locations during this field campaign, and Appendix B lists all the study principal investigators and participants.

  7. AMS/NRCan Joint Survey Report: Aerial Campaign

    SciTech Connect (OSTI)

    Wasiolek, Piotr; Stampahar, Jez; Malchow, Rusty; Stampahar, Tom; Lukens, Mike; Seywerd, Henry; Fortin, Richard; Harvey, Brad; Sinclair, Laurel

    2014-12-31

    In January 2014 the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA) Aerial Measuring System (AMS) and the Natural Resources Canada (NRCan) Nuclear Emergency Response project conducted a series of joint surveys at a number of locations in Nevada including the Nevada National Security Site (NNSS). The goal of this project was to compare the responses of the two agencies aerial radiation detection systems and data analysis techniques. This test included varied radioactive surface contamination levels and isotopic composition experienced at the NNSS and the differing data processing techniques utilized by the respective teams. Because both teams used the commercial aerial radiation detection systems from Radiation Solutions, Inc., the main focus of the campaign was to investigate the data acquisition techniques, data analysis, and ground-truth verification. The NRCan system consisted of four 4" 4" 16" NaI(Tl) scintillator crystals of which two were externally mounted in a modified commercial cargo basket certified for the Eurocopter AS350; the NNSA AMS system consisted of twelve 2" 4" 16" NaI(Tl) crystals in externally mounted dedicated pods. For NRCan, the joint survey provided an opportunity to characterize their systems response to extended sources of various fission products at the NNSS. Since both systems play an important role in their respective countries national framework of radiological emergency response and are subject to multiple mutual cooperation agreements, it was important for each country to obtain more thorough knowledge of how they would employ these important assets and define the roles that they would each play in an actual response.

  8. Hawaii Energy Strategy program. Annual report 1993

    SciTech Connect (OSTI)

    Not Available

    1993-12-31

    This is the second annual report on the Hawaii Energy Strategy (HES) program which began on March 2, 1992, under a Cooperative Agreement (FCO3-92F19l68) with the United States Department of Energy (USDOE). The HES program is scheduled for completion by December 31, 1994. As outlined in the Statement of Joint Objectives. The purpose of the study is to develop an integrated State of Hawaii energy strategy, including an assessment of the State`s fossil fuel reserve requirements and the most effective way to meet those needs, the availability and practicality of increasing the use of native energy resources, potential alternative fossil energy technologies such as coal gasification and potential energy efficiency measures which could lead to demand reduction. This work contributes to the (US)DOE mission, will reduce the State`s vulnerability to energy supply disruptions and contributes to the public good.

  9. Diagnostic development for determining the joint temperature/soot statistics in hydrocarbon-fueled pool fires : LDRD final report.

    SciTech Connect (OSTI)

    Casteneda, Jaime N.; Frederickson, Kraig; Grasser, Thomas W.; Hewson, John C.; Kearney, Sean Patrick; Luketa, Anay Josephine

    2009-09-01

    A joint temperature/soot laser-based optical diagnostic was developed for the determination of the joint temperature/soot probability density function (PDF) for hydrocarbon-fueled meter-scale turbulent pool fires. This Laboratory Directed Research and Development (LDRD) effort was in support of the Advanced Simulation and Computing (ASC) program which seeks to produce computational models for the simulation of fire environments for risk assessment and analysis. The development of this laser-based optical diagnostic is motivated by the need for highly-resolved spatio-temporal information for which traditional diagnostic probes, such as thermocouples, are ill-suited. The in-flame gas temperature is determined from the shape of the nitrogen Coherent Anti-Stokes Raman Scattering (CARS) signature and the soot volume fraction is extracted from the intensity of the Laser-Induced Incandescence (LII) image of the CARS probed region. The current state of the diagnostic will be discussed including the uncertainty and physical limits of the measurements as well as the future applications of this probe.

  10. Utility Partnerships Program Overview

    SciTech Connect (OSTI)

    2014-10-03

    Document describes the Utility Partnerships Program within the U.S. Department of Energy's Federal Energy Management Program.

  11. Mentoring Program | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mentoring Program Mentoring Program Mentee Questionnaire Mentor Questionnaire Ideas for Mentoring Program Activities

  12. Machinist Pipeline/Apprentice Program Program Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Machinist Pipeline/Apprentice Program Program Description The Machinist Pipeline Program was created by the Prototype Fabrication Division to fill a critical need for skilled journeyworker machinists. It is based on a program developed by the National Institute for Metalworking Skills (NIMS) in conjunction with metalworking trade associations to develop and maintain a globally competitive U.S. workforce. The goal is to develop and implement apprenticeship programs that are aligned with

  13. Solder Joints of Power Electronics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    10 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. PDF icon pm015_muralidharan_2010_p

  14. Optical Fiber Sensors For Monitoring Joint Articulation And Chest Expansion Of A Human Body

    DOE Patents [OSTI]

    Muhs, Jeffrey D. (Lenoir City, TN); Allison, Stephen W. (Knoxville, TN)

    1997-12-23

    Fiber-optic sensors employing optical fibers of elastomeric material are incorporated in devices adapted to be worn by human beings in joint and chest regions for the purpose of monitoring and measuring the extent of joint articulation and chest expansion especially with respect to time.

  15. Joint Genome Institute (JGI) | U.S. DOE Office of Science (SC)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Joint Genome Institute (JGI) Biological and Environmental Research (BER) BER Home About Research Facilities User Facilities Atmospheric Radiation Measurement Climate Research Facility (ARM) Environmental Molecular Sciences Laboratory (EMSL) Joint Genome Institute (JGI) Science Highlights Benefits of BER Funding Opportunities Biological & Environmental Research Advisory Committee (BERAC) Community Resources Contact Information Biological and Environmental Research U.S. Department of Energy

  16. A Complexity Science-Based Framework for Global Joint Operations Analysis to Support Force Projection: LDRD Final Report.

    SciTech Connect (OSTI)

    Lawton, Craig R.

    2015-01-01

    The military is undergoing a significant transformation as it modernizes for the information age and adapts to address an emerging asymmetric threat beyond traditional cold war era adversaries. Techniques such as traditional large-scale, joint services war gaming analysis are no longer adequate to support program evaluation activities and mission planning analysis at the enterprise level because the operating environment is evolving too quickly. New analytical capabilities are necessary to address modernization of the Department of Defense (DoD) enterprise. This presents significant opportunity to Sandia in supporting the nation at this transformational enterprise scale. Although Sandia has significant experience with engineering system of systems (SoS) and Complex Adaptive System of Systems (CASoS), significant fundamental research is required to develop modeling, simulation and analysis capabilities at the enterprise scale. This report documents an enterprise modeling framework which will enable senior level decision makers to better understand their enterprise and required future investments.

  17. COMPARISON OF SHEAR STRENGTH OF CERAMIC JOINTS DETERMINED BY VARIOUS TEST METHODS WITH SMALL SPECIMENS

    SciTech Connect (OSTI)

    Katoh, Yutai; Kiggans Jr, James O; Khalifa, Hesham; Back, Christina A.; Hinoki, Tatsuya; Ferraris, Monica

    2015-01-01

    Four different shear test methods i.e. doubled notched shear test, asymmetrical four point bend test, Iosipescu test, and torsion test, were investigated for their ability to evaluate one standard SiC to SiC ceramic brittle joint while using small size specimens. Double notched shear test showed higher stress concentration at the notch base and a lower nominal shear strength. Both asymmetrical four point bend test and Iosipescu test utilized epoxy jointed metal extensors, which failed during test and caused misalignment and tensile type of failure. Torsion test can deliver true shear loading. However, base material failure was observed for the torsion joint samples in this study. None of the tests can successfully induce true shear failure of the joint because the joint is stronger and tougher than the SiC substrate. Torsion test appears to be promising because of the pure shear loading, less stress concentration, and easy alignment.

  18. Prototype integration of the joint munitions assessment and planning model with the OSD threat methodology

    SciTech Connect (OSTI)

    Lynn, R.Y.S.; Bolmarcich, J.J.

    1994-06-01

    The purpose of this Memorandum is to propose a prototype procedure which the Office of Munitions might employ to exercise, in a supportive joint fashion, two of its High Level Conventional Munitions Models, namely, the OSD Threat Methodology and the Joint Munitions Assessment and Planning (JMAP) model. The joint application of JMAP and the OSD Threat Methodology provides a tool to optimize munitions stockpiles. The remainder of this Memorandum comprises five parts. The first is a description of the structure and use of the OSD Threat Methodology. The second is a description of JMAP and its use. The third discusses the concept of the joint application of JMAP and OSD Threat Methodology. The fourth displays sample output of the joint application. The fifth is a summary and epilogue. Finally, three appendices contain details of the formulation, data, and computer code.

  19. U.S. Department of Energy Biomass Program: Overview of U.S. Energy Policies

    Broader source: Energy.gov [DOE]

    At the February 13, 2008 joint quarterly Web conference for DOE's Biomass and Clean Cities programs, Jim Spaeth (DOEs Golden Field Office) discussed Federal energy policy, including the Energy Independence and Security Act of 2007 and key provisions of the pending Farm Bill.

  20. Electrical detection of liquid lithium leaks from pipe joints

    SciTech Connect (OSTI)

    Schwartz, J. A. Jaworski, M. A.; Mehl, J.; Kaita, R.; Mozulay, R.

    2014-11-15

    A test stand for flowing liquid lithium is under construction at Princeton Plasma Physics Laboratory. As liquid lithium reacts with atmospheric gases and water, an electrical interlock system for detecting leaks and safely shutting down the apparatus has been constructed. A defense in depth strategy is taken to minimize the risk and impact of potential leaks. Each demountable joint is diagnosed with a cylindrical copper shell electrically isolated from the loop. By monitoring the electrical resistance between the pipe and the copper shell, a leak of (conductive) liquid lithium can be detected. Any resistance of less than 2 k? trips a relay, shutting off power to the heaters and pump. The system has been successfully tested with liquid gallium as a surrogate liquid metal. The circuit features an extensible number of channels to allow for future expansion of the loop. To ease diagnosis of faults, the status of each channel is shown with an analog front panel LED, and monitored and logged digitally by LabVIEW.

  1. Utilizing the sequential probability ratio test for building joint monitoring

    SciTech Connect (OSTI)

    Allen, D. W.; Sohn, H.; Worden, K.; Farrar, C. R.

    2002-01-01

    In this application of the statistical pattern recognition paradigm, a prediction model of a chosen feature is developed from the time domain response of a baseline structure. After the model is developed, subsequent feature sets are tested against the model to determine if a change in the feature has occurred. In the proposed statistical inference for damage identification there are two basic hypotheses; (1) the model can predict the feature, in which case the structure is undamaged or (2) the model can not accurately predict the feature, suggesting that the structure is damaged. The Sequential Probability Ratio Test (SPRT) develops a statistical method that quickly arrives at a decision between these two hypotheses and is applicable to continuous monitoring. In the original formulation of the SPRT algorithm, the feature is assumed to be Gaussian and thresholds are set accordingly. It is likely, however, that the feature used for damage identification is sensitive to the tails of the distribution and that the tails may not necessarily be governed by Gaussian characteristics. By modeling the tails using the technique of Extreme Value Statistics, the hypothesis decision thresholds for the SPRT algorithm may be set avoiding the normality assumption. The SPRT algorithm is utilized to decide if the test structure is undamaged or damaged and which joint is exhibiting the change.

  2. IMPACTS: Industrial Technologies Program, Summary of Program...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    91 DOE Industrial Technologies Program Appendix 7: Methodology for Technology Tracking and Assessment of Benefits u Technology Tracking......

  3. Development of extruded and molded straight joint for ultra high-voltage XLPE cable

    SciTech Connect (OSTI)

    Shimomura, T.; Ando, K.; Asahi, K.; Sugiyama, K.

    1986-01-01

    In Japan, 154-kV crosslinked polyethylene-insulated cables (XLPE) are already in use for long-distance tranmission lines, but 275-kV XLPE cables are used only for short-distance lines (without joints) on the premises of power-generation plants and substations. 275-kV XLPE cable is expected to be used for long-distance transmission lines in the near future because of its overall cost advantage. To respond to this need, a straight-through joint with the same reliability as the cable should be developed. Reliable joints should be formed and molded with the same curable PE compounds as the cable insulation. At present, 154-kV XLPE cables for long-distance transmission lines are usually constructed with the joint comprising XLPE insulation wrapped with curable PE tape and molded by heating. However, this taped molded joint has the disadvantages of troublesome tape handling. On the other hand, extruded molded joints are constructed by injecting curable melted PE into a mold with an extruder, eliminating contamination. The report describes the characteristics of the extruded and molded joint developed for 154, 275 and 500 kV class XLPE cables.

  4. Caterpillar Light Truck Clean Diesel Program

    SciTech Connect (OSTI)

    Robert L. Miller; Kevin P. Duffy; Michael A. Flinn; Steve A. Faulkner; Mike A. Graham

    1999-04-26

    In 1998, light trucks accounted for over 48% of new vehicle sales in the U.S. and well over half the new Light Duty vehicle fuel consumption. The Light Truck Clean Diesel (LTCD) program seeks to introduce large numbers of advanced technology diesel engines in light-duty trucks that would improve their fuel economy (mpg) by at least 50% and reduce our nation's dependence on foreign oil. Incorporating diesel engines in this application represents a high-risk technical and economic challenge. To meet the challenge, a government-industry partnership (Department of Energy, diesel engine manufacturers, and the automotive original equipment manufacturers) is applying joint resources to meet specific goals that will provide benefits to the nation. [1] Caterpillar initially teamed with Ford Motor Company on a 5 year program (1997-2002) to develop prototype vehicles that demonstrate a 50% fuel economy improvement over the current 1997 gasoline powered light truck vehicle in this class while complying with EPA's Tier II emissions regulations. The light truck vehicle selected for the demonstration is a 1999 Ford F150 SuperCab. To meet the goals of the program, the 4.6 L V-8 gasoline engine in this vehicle will be replaced by an advanced compression ignition direct injection (CIDI) engine. Key elements of the Caterpillar LTCD program plan to develop the advanced CIDI engine are presented in this paper.

  5. Y-12 Apprentice Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Apprentice Program Over the years Y-12 has produced numerous training programs. Many of them have been developed at Y-12 to meet special needs. The training programs have ranged...

  6. Joint Actinide Shock Physics Experimental Research | National Nuclear

    National Nuclear Security Administration (NNSA)

    Security Administration Actinide Shock Physics Experimental Research | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios Congressional Testimony Fact Sheets Newsletters Press Releases Photo

  7. DOE Announces Funding for U.S.-India Joint Clean Energy Research and

    Energy Savers [EERE]

    Development Center | Department of Energy for U.S.-India Joint Clean Energy Research and Development Center DOE Announces Funding for U.S.-India Joint Clean Energy Research and Development Center May 16, 2011 - 12:00am Addthis Washington, D.C. - As part of the Partnership to Advance Clean Energy announced by President Obama and Prime Minister Singh of India last November, the Department of Energy has committed $25 million over the next five years to support the U.S.-India Joint Clean Energy

  8. Energy Department Announces Selections for U.S.-India Joint Clean Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research and Development Center | Department of Energy Selections for U.S.-India Joint Clean Energy Research and Development Center Energy Department Announces Selections for U.S.-India Joint Clean Energy Research and Development Center April 13, 2012 - 12:01pm Addthis WASHINGTON, DC - The U.S. Department of Energy today announced the selections for three consortia that will make up the $125 million U.S.-India Joint Clean Energy Research and Development Center (JCERDC). These consortia - led

  9. Joint Summer School on "Atomic-level Response of Materials to Irradiation"

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    | U.S. DOE Office of Science (SC) Joint Summer School on "Atomic-level Response of Materials to Irradiation" Energy Frontier Research Centers (EFRCs) EFRCs Home Centers Research Science Highlights News & Events EFRC News EFRC Events DOE Announcements Publications History Contact BES Home 04.09.10 Joint Summer School on "Atomic-level Response of Materials to Irradiation" Print Text Size: A A A Subscribe FeedbackShare Page June 20 - 25, 2010 :: Joint Summer School on

  10. Developments in precision casing joint and radioactive bullet measurements for compaction monitoring

    SciTech Connect (OSTI)

    Allen, D.R.

    1981-01-01

    A method has been developed in Wilmington Field, California, for measuring oil zone compaction and expansion by the deformation in well casing. Possible formation compaction is also directly investigated by locating radioactive bullets previously placed in the formation. Random joint lengths, under field conditions, have been repeatedly measured and remeasured with a standard deviation of .0159 ft. (4.8 mm). An alternate system, developed by R.A. Ruedrich et al utilized multiple collar locators and specially milled casing joints. Both systems can be applied to field situations where random joint lengths are found; however, the odometer system should be more reliable under these conditions. 5 refs.

  11. 11th Annual Energy Department Joint Genome Institute Genomics of Energy &

    Energy Savers [EERE]

    Environment Meeting | Department of Energy 11th Annual Energy Department Joint Genome Institute Genomics of Energy & Environment Meeting 11th Annual Energy Department Joint Genome Institute Genomics of Energy & Environment Meeting March 21, 2016 9:00AM PDT to March 25, 2016 4:00PM PDT Marriott Hotel 2355 North Main Street Walnut Creek, California 94596 The 11th Annual Energy Department (DOE) Joint Genome Institute Genomics of Energy & Environment Meeting will be held March 21-25,

  12. Volunteer Program FAQs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Volunteer Program FAQs FAQs About Volunteer Program Your questions about volunteering answered. . . General info about LANL volunteering 2016 FAQs (pdf) Vecinos Volunteer Program What is the LANL Vecinos Volunteer Program? The LANL Vecinos Volunteer Program connects great employee and retiree volunteers with local nonprofit organizations needing assistance. What does the word 'Vecinos' mean? Vecinos, the name of the LANL Volunteer Program, means "neighbors" in Spanish. Our employee and

  13. Programming on Franklin

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Programming Programming on Franklin Compiling Codes on Franklin Cray provides a convenient set of wrapper commands which should be used in almost all cases for compiling and...

  14. Weapons Program Associate Directors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    integration we have achieved between the various components of the program," said Bret Knapp, Principal Associate Director for Weapons Programs. "They have both done an...

  15. Voluntary Separation Programs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... time limits of the program, the ages and job titles of everyone eligible for the ... Separation Program. The separation package has been explained to my satisfaction. ...

  16. TECHNOLOGY PROGRAM PLAN

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... The Department of Energy's (DOE) Advanced Combustion Systems program is conducted under the Clean Coal Research Program (CCRP). DOE's overarching mission is to increase the energy ...

  17. Hydropower Program Technology Overview

    SciTech Connect (OSTI)

    Not Available

    2001-10-01

    New fact sheets for the DOE Office of Power Technologies (OPT) that provide technology overviews, description of DOE programs, and market potential for each OPT program area.

  18. Energy Smart Grocer Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Commercial Program Development Commercial Current Promotions Industrial Federal Agriculture EnergySmart Grocer Program Close-out BPA and CLEAResult have concluded negotiations...

  19. STEM Education Program Inventory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    box to the right.)* Workforce Development Student Programs Public Engagement in Life Long Learning TeacherFaculty Prefessional Development Other Type of Program (Other) To select...

  20. ARM - Program Fact Sheets

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MaterialsProgram Fact Sheets Publications Journal Articles Conference Documents Program Documents Technical Reports Publications Database Public Information Materials Image Library...

  1. SEP Program Transition Tables

    Broader source: Energy.gov [DOE]

    The Program Transition Tables provide information concerning the level of effort required to move from a traditional, industrial incentive program to Strategic Energy Management, ISO 50001, or SEP.

  2. Assistance Program, State Energy Program, Energy Efficiency and...

    Energy Savers [EERE]

    Assistance Program, State Energy Program, Energy Efficiency and Conservation Block Grants Assistance Program, State Energy Program, Energy Efficiency and Conservation Block Grants ...

  3. State Energy-Efficient Appliance Rebate Program: Volume 1 - Program...

    Energy Savers [EERE]

    State Energy-Efficient Appliance Rebate Program: Volume 1 - Program Design Lessons Learned State Energy-Efficient Appliance Rebate Program: Volume 1 - Program Design Lessons...

  4. Joint Statement by Energy Ministers of G8, The People's Republic...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    People's Republic of China, India and The Republic of Korea (June 2008) Joint Statement by Energy Ministers of G8, The People's Republic of China, India and The Republic of Korea ...

  5. Joint Statement by Energy Ministers of G8, The People's Republic...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The People's Republic of China, India and The Republic of Korea Joint Statement by Energy Ministers of G8, The People's Republic of China, India and The Republic of Korea A ...

  6. U.S.-India Joint Clean Energy Research and Development Center...

    Broader source: Energy.gov (indexed) [DOE]

    123.1) - U.S. Applicants Only 5. Budget Application Form - Indian Applicants Only 6. U.S.-India Joint Clean Energy Research and Development Center Agreement 7. S&T Agreement 8....

  7. 2014 SAME Mid-Atlantic Regional Joint Engineer Training Symposium (JETS)

    Broader source: Energy.gov [DOE]

    The Society of American Military Engineers (SAME) presents its Mid-Atlantic Regional Joint Engineer Training Symposium (JETS) with the topic Navigating the New Normal: Partnerships for the Future.

  8. United States and France Sign Joint Statement on Civil Liability for Nuclear Damage

    Broader source: Energy.gov [DOE]

    The United States and France today issued the Joint Statement on Civil Liability for Nuclear Damage that sets forth the common views of the United States and France on civil nuclear liability

  9. Grinding assembly, grinding apparatus, weld joint defect repair system, and methods

    DOE Patents [OSTI]

    Larsen, Eric D.; Watkins, Arthur D.; Bitsoi, Rodney J.; Pace, David P.

    2005-09-27

    A grinding assembly for grinding a weld joint of a workpiece includes a grinder apparatus, a grinder apparatus includes a grinding wheel configured to grind the weld joint, a member configured to receive the grinding wheel, the member being configured to be removably attached to the grinder apparatus, and a sensor assembly configured to detect a contact between the grinding wheel and the workpiece. The grinding assembly also includes a processing circuitry in communication with the grinder apparatus and configured to control operations of the grinder apparatus, the processing circuitry configured to receive weld defect information of the weld joint from an inspection assembly to create a contour grinding profile to grind the weld joint in a predetermined shape based on the received weld defect information, and a manipulator having an end configured to carry the grinder apparatus, the manipulator further configured to operate in multiple dimensions.

  10. Modular multimorphic kinematic arm structure and pitch and yaw joint for same

    DOE Patents [OSTI]

    Martin, H.L.; Williams, D.M.; Holt, W.E.

    1987-04-21

    A multimorphic kinematic manipulator arm is provided with seven degrees of freedom and modular kinematic redundancy through identical pitch/yaw, shoulder, elbow and wrist joints and a wrist roll device at the wrist joint, which further provides to the manipulator arm an obstacle avoidance capability. The modular pitch/yaw joints are traction drive devices which provide backlash free operation with smooth torque transmission and enhanced rigidity. A dual input drive arrangement is provided for each joint resulting in a reduction of the load required to be assumed by each drive means and providing selective pitch and yaw motions by control of the relative rotational directions of the input drive means. 12 figs.

  11. Report on the 1ST Meeting of the Joint Working Group on

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in USA, November 4-17, 2010 A. PURPOSE The purpose of the 2nd meeting of the U.S.-China Joint Working Group on Safety was to informally evaluate the programmatic aspects of...

  12. United States-Russia Joint Statement on the Results of the Nuclear...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    U.S. and Russia on civil nuclear energy and nuclear security. Read the joint statement (PDF - 412 kb) signed by Deputy Secretary Poneman and Director Kirienko. Media contact(s):...

  13. Joint Technical Operations Team | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Technical Operations Team | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios Congressional Testimony Fact Sheets Newsletters Press Releases Photo Gallery Jobs Apply for Our Jobs Our Jobs Working

  14. Joint Venture Established Between Russian Weapons Plant And the Largest

    National Nuclear Security Administration (NNSA)

    Dialysis Provider in the U.S. | National Nuclear Security Administration Venture Established Between Russian Weapons Plant And the Largest Dialysis Provider in the U.S. | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget

  15. Fact Sheet: United States-Japan Joint Nuclear Energy Action Plan

    Broader source: Energy.gov (indexed) [DOE]

    Sheet: United States-Japan Joint Nuclear Energy Action Plan The United States-Japan Joint Nuclear Energy Action Plan is intended to provide a framework for bilateral collaboration in nuclear energy. This Action Plan builds upon our significant, longstanding civilian nuclear cooperation, and will contribute to increasing energy security and managing nuclear waste, addressing nuclear nonproliferation and climate change, advancing goals put forth in President Bush's Global Nuclear Energy

  16. DOE-EERE/NIST Joint Workshop on Combinatorial Materials Science for

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Applications in Energy | Department of Energy EERE/NIST Joint Workshop on Combinatorial Materials Science for Applications in Energy DOE-EERE/NIST Joint Workshop on Combinatorial Materials Science for Applications in Energy The Hydrogen Storage Subprogram of the U.S. Department of Energy co-hosted with the NIST (National Institute of Standards and Technology) Combinatorial Methods Center (NCMC) a workshop titled "High-Throughput/Combinatorial Material Science for Applications in

  17. Integrated, proportionally controlled, and naturally compliant universal joint actuator with controllable stiffness

    DOE Patents [OSTI]

    Borenstein, Johann; Granosik, Grzegorz

    2005-03-22

    An apparatus for traversing obstacles having an elongated, round, flexible body that includes a plurality of segments interconnected by an integrated joint actuator assembly. The integrated joint actuator assembly includes a plurality of bellows-type actuators individually coupling adjacent segments to permit pivotal actuation of the apparatus therebetween. A controller is employed to maintain proper positional control and stiffness control while minimize air flow.

  18. 11th Annual DOE Joint Genome Institute Genomics of Energy & Environment Meeting

    Broader source: Energy.gov [DOE]

    The 11th Annual DOE Joint Genome Institute Genomics of Energy & Environment Meeting will be held March 21–25, 2016 in Walnut Creek, California. The meeting will gather together experts and researchers working in energy and environmental genomics and synthetic biology, and it will have a special focus on the work done at the DOE Joint Genome Institute. Bioenergy Technologies Office Technology Manager Daniel Fishman will be in attendance.

  19. JOINT EPA/DOE STATEMENT: Radiation Monitors Confirm That No Radiation

    Energy Savers [EERE]

    Levels of Concern Have Reached the United States | Department of Energy JOINT EPA/DOE STATEMENT: Radiation Monitors Confirm That No Radiation Levels of Concern Have Reached the United States JOINT EPA/DOE STATEMENT: Radiation Monitors Confirm That No Radiation Levels of Concern Have Reached the United States March 18, 2011 - 12:00am Addthis WASHINGTON - The United States Government has an extensive network of radiation monitors around the country and no radiation levels of concern have been

  20. EPRI-DOE Joint Report on Fossil Fleet Transition with Fuel Changes and

    Energy Savers [EERE]

    Large Scale Variable Renewable Integration Now Available | Department of Energy EPRI-DOE Joint Report on Fossil Fleet Transition with Fuel Changes and Large Scale Variable Renewable Integration Now Available EPRI-DOE Joint Report on Fossil Fleet Transition with Fuel Changes and Large Scale Variable Renewable Integration Now Available October 15, 2015 - 3:31pm Addthis A new report "Fossil Fleet Transition with Fuel Changes and Large Scale Variable Renewable Integration" from the

  1. DOE, BOEMRE and NOAA Announce Nearly $5 Million for Joint Environmental

    Energy Savers [EERE]

    Research Projects to Advance Ocean Renewable Energy | Department of Energy DOE, BOEMRE and NOAA Announce Nearly $5 Million for Joint Environmental Research Projects to Advance Ocean Renewable Energy DOE, BOEMRE and NOAA Announce Nearly $5 Million for Joint Environmental Research Projects to Advance Ocean Renewable Energy October 26, 2010 - 12:00am Addthis WASHINGTON, DC - The Department of Energy (DOE), Bureau of Ocean Energy Management, Regulation and Enforcement (BOEMRE), and the

  2. United States and Japan Sign Joint Nuclear Energy Action Plan to Promote

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Nuclear Energy Cooperation | Department of Energy Japan Sign Joint Nuclear Energy Action Plan to Promote Nuclear Energy Cooperation United States and Japan Sign Joint Nuclear Energy Action Plan to Promote Nuclear Energy Cooperation April 25, 2007 - 12:36pm Addthis WASHINGTON, DC - United States Department of Energy Secretary Samuel W. Bodman and Japan's Ministers Akira Amari, Bunmei Ibuki, and Taro Aso, this week presented to U.S. President George W. Bush and Japanese Prime Minister Shinzo

  3. Accommodations for Joint Facilities User Forum on Data-Intensive Computing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    & HPCOR Accommodations Accommodations for Joint Facilities User Forum on Data-Intensive Computing & HPCOR Both the Joint Facilities User Forum on Data-Intensive Computing and the DOE HPCOR meetings are being held in downtown Oakland, CA. We have reserved room blocks at two locations in Berkeley, CA. We recommend making your reservations as soon as possible because hotel rooms in the San Francisco Bay Area are in great demand. Hotel Shattuck Plaza Reservation cutoff date is May 23,

  4. Joint Motion to Intervene of Northern States Power Company (Minnesota) et

    Office of Environmental Management (EM)

    al. on the Proposed Open Access Requirements | Department of Energy Motion to Intervene of Northern States Power Company (Minnesota) et al. on the Proposed Open Access Requirements Joint Motion to Intervene of Northern States Power Company (Minnesota) et al. on the Proposed Open Access Requirements Joint motion to intervene of the Northern States Power Company (Minnesota), the Northern States Power Company (Wisconsin), and NRG Energy, Incl on the Proposed Open Access Requirements for

  5. Joint Statement on Future U.S.-Russia Nuclear Energy and Nonproliferation

    Office of Environmental Management (EM)

    Collaboration Following Russian Delegation Visit to the United States | Department of Energy Joint Statement on Future U.S.-Russia Nuclear Energy and Nonproliferation Collaboration Following Russian Delegation Visit to the United States Joint Statement on Future U.S.-Russia Nuclear Energy and Nonproliferation Collaboration Following Russian Delegation Visit to the United States December 10, 2013 - 2:30pm Addthis News Media Contact (202) 586-4940 U.S. Secretary of Energy Ernest Moniz and

  6. EPRI-DOE Joint Report Focuses on Fossil Fleet Transition with Fuel Changes

    Office of Environmental Management (EM)

    and Large Scale Variable Renewable Integration | Department of Energy EPRI-DOE Joint Report Focuses on Fossil Fleet Transition with Fuel Changes and Large Scale Variable Renewable Integration EPRI-DOE Joint Report Focuses on Fossil Fleet Transition with Fuel Changes and Large Scale Variable Renewable Integration October 15, 2015 - 8:58am Addthis A new report, "Fossil Fleet Transition with Fuel Changes and Large Scale Variable Renewable Integration" from the Electric Power Research

  7. Savannah River Ecology Laboratory - Outreach Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Coyote's webpage

  8. Savannah River Ecology Laboratory - Outreach Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Program Field Guide PDF

  9. Internship Programs Calendar | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Internship Programs Calendar

  10. Beryllium Program Feedback - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hanford Site Wide Programs Beryllium Program Beryllium Program Feedback About Us Beryllium Program Beryllium Program Points of Contact Beryllium Facilities & Areas Beryllium Program Information Hanford CBDPP Committee Beryllium FAQs Beryllium Related Links Hanford Beryllium Awareness Group (BAG) Program Performance Assessments Beryllium Program Feedback Beryllium Health Advocates Primary Contractors/Employers Medical Testing and Surveillance Facilities General Resources Beryllium Program

  11. Biomass Program Overview

    SciTech Connect (OSTI)

    2010-01-01

    This document provides an overview of the Biomass Program's mission, strategic goals, and research approach.

  12. Better Buildings Neighborhood Program

    Broader source: Energy.gov [DOE]

    U.S. Department of Energy Better Buildings Neighborhood Program: Business Models Guide, October 27, 2011.

  13. Home Energy Score Program

    Broader source: Energy.gov [DOE]

    Residential Buildings Integration Project for the 2013 Building Technologies Office's Program Peer Review

  14. Laser Programs Highlights 1998

    SciTech Connect (OSTI)

    Lowdermilk, H.; Cassady, C.

    1999-12-01

    This report covers the following topics: Commentary; Laser Programs; Inertial Confinement Fusion/National Ignition Facility (ICF/NIF); Atomic Vapor Laser Isotope Separation (AVLIS); Laser Science and Technology (LS&T); Information Science and Technology Program (IS&T); Strategic Materials Applications Program (SMAP); Medical Technology Program (MTP) and Awards.

  15. Oil shale, tar sand, coal research advanced exploratory process technology, jointly sponsored research. Quarterly technical progress report, October--December 1992

    SciTech Connect (OSTI)

    Speight, J.G.

    1992-12-31

    Accomplishments for the past quarter are presented for the following five tasks: oil shale; tar sand; coal; advanced exploratory process technology; and jointly sponsored research. Oil shale research covers oil shale process studies. Tar sand research is on process development of Recycle Oil Pyrolysis and Extraction (ROPE) Process. Coal research covers: coal combustion; integrated coal processing concepts; and solid waste management. Advanced exploratory process technology includes: advanced process concepts;advanced mitigation concepts; and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; CROW field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; PGI demonstration project; operation and evaluation of the CO{sub 2} HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesaverde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced oil recovery techniques; surface process study for oil recovery using a thermal extraction process; NMR analysis of samples from the ocean drilling program; in situ treatment of manufactured gas plant contaminated soils demonstration program; and solid state NMR analysis of naturally and artificially matured kerogens.

  16. SEP Program Planning Template ("Program Planning Template") ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    File Program Planning Template More Documents & Publications Commute Mode Switching Impact Tool Energy Intensity Indicators Data Refrigerator-Freezers (multiple defrost waiver)...

  17. State Energy Program & Weatherization Assistance Program: Update

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Area 2 - Stimulating Energy Efficiency Action * Policy and program frameworks to support investment in cost-effective energy efficiency; establish or increase a statewide energy ...

  18. IMPACTS: Industrial Technologies Program, Summary of Program...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    181 DOE Industrial Technologies Program Appendix 5: Method of Calculating Results for the Save Energy Now Initiative u Large Plant Assessments ......

  19. Diffusion of trichloroethylene through the threaded joints of PVC (polyvinylchloride) pipe

    SciTech Connect (OSTI)

    Jerome, K.M. . Dept. of Civil Engineering)

    1990-12-01

    The data engineers and scientists use to determine if the groundwater supply is contaminated are derived from analysis of samples taken largely from monitoring wells. For these data to be reliable several factors must be considered. One factor is the integrity of the monitoring well. In this project, emphasis has been placed on the potential impact on water quality caused by diffusion across the threaded joints of PVC pipe. In this study, the diffusion of trichloroethylene across several common types of threaded joints (i.e., square flush, modified ACME, modified ACME stub, and ACME) has been measured. Samples were obtained from the water inside the pipe sections and analyzed for trichloroethylene by gas chromatography. Breakthrough occurs within days of the samples being placed in the baths. The softened PVC joints of the pipes in the pure trichloroethylene split before the first sample interval of 1.5 weeks. The data show great variability in casting joints from the same manufacturer, and indicate a need for increased precision in the manufacturing of the PVC pipe joints. A one-dimensional diffusion model is used to determine an equivalent gap size through which the diffusion occurs. Flow rates through the threaded joints are calculated by using the equivalent gap width and a formula for flow through a rectangular duct running full. Comparison of the results of the gap size calculations and of the flow rates is presented. 20 refs., 13 figs. 11 tabs.

  20. Multipacting in a grooved choke joint at SRF gun for BNL ERL prototype

    SciTech Connect (OSTI)

    Xu, W.; Ben-Zvi, I.; Belomestnykh, S.; Burrill, A.; Holmes, D.; Kayran, D.; McIntyre, G.; Sheehy, B.

    2011-03-28

    The 703 MHz superconducting gun for BNL ERL prototype was tested at JLab with and without choke-joint and cathode stalk. Without choke-joint and cathode stalk, the gradient reached was 25 MV/m with Q{sup 0} {approx} 6E9. The gun cathode insertion port is equipped with a grooved choke joint for multipacting suppression. We carried out tests with choke-joint and cathode stalk. The test results show that there are at least two barriers at about 3.5 MV/m and 5 MV/m. We considered several possibilities and finally found that fine details of the grooved shape are important for multipacting suppression. A triangular groove with round crest may cause strong multipacting in the choke-joint at 3.5 MV/m, 5 MV/m and 10 MV/m. This paper presents the primary test results of the gun and discusses the multipacting analysis in the choke-joint. It also suggests possible solutions for the gun and multipacting suppressing for a similar structure.