Powered by Deep Web Technologies
Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Gravitational Instability of Yang-Mills Cosmologies  

E-Print Network [OSTI]

The gravitational instability of Yang-Mills cosmologies is numerically studied with the hamiltonian formulation of the spherically symmetric Einstein-Yang-Mills equations with SU(2) gauge group. On the short term, the expansion dilutes the energy densities of the Yang-Mills fluctuations due to their conformal invariance. In this early regime, the gauge potentials appear oscillating quietly in an interaction potential quite similar to the one of the homogeneous case. However, on the long term, the expansion finally becomes significantly inhomogeneous and no more mimics a conformal transformation of the metric. Thereafter, the Yang-Mills fluctuations enter a complex non-linear regime, accompanied by diffusion, while their associated energy contrasts grow.

A. Fuzfa

2003-10-06T23:59:59.000Z

2

Uranium Mill Tailings Management  

SciTech Connect (OSTI)

This book presents the papers given at the Fifth Symposium on Uranium Mill Tailings Management. Advances made with regard to uranium mill tailings management, environmental effects, regulations, and reclamation are reviewed. Topics considered include tailings management and design (e.g., the Uranium Mill Tailings Remedial Action Project, environmental standards for uranium mill tailings disposal), surface stabilization (e.g., the long-term stability of tailings, long-term rock durability), radiological aspects (e.g. the radioactive composition of airborne particulates), contaminant migration (e.g., chemical transport beneath a uranium mill tailings pile, the interaction of acidic leachate with soils), radon control and covers (e.g., radon emanation characteristics, designing surface covers for inactive uranium mill tailings), and seepage and liners (e.g., hydrologic observations, liner requirements).

Nelson, J.D.

1982-01-01T23:59:59.000Z

3

Biological Kraft Chemical Recycle for Augmentation of Recovery Furnace Capacity  

SciTech Connect (OSTI)

The chemicals used in pulping of wood by the kraft process are recycled in the mill in the recovery furnace, which oxidizes organics while simultaneously reducing sulfate to sulfide. The recovery furnace is central to the economical operation of kraft pulp mills, but it also causes problems. The total pulp production of many mills is limited by the recovery furnace capacity, which cannot easily be increased. The furnace is one of the largest sources of air pollution (as reduced sulfur compounds) in the kraft pulp mill.

Stuart E. Strand

2001-12-06T23:59:59.000Z

4

Refinery Capacity Report  

Gasoline and Diesel Fuel Update (EIA)

Refinery Capacity Report Released: June 15, 2006 Refinery Capacity Report --- Full report in PDF (1 MB) XLS --- Refinery Capacity Data by individual refinery as of January 1, 2006...

5

Capacity Markets for Electricity  

E-Print Network [OSTI]

ternative Approaches for Power Capacity Markets”, Papers andprof id=pjoskow. Capacity Markets for Electricity [13]Utility Commission- Capacity Market Questions”, available at

Creti, Anna; Fabra, Natalia

2004-01-01T23:59:59.000Z

6

Investment-Grade Compressed Air System Audit, Analysis, and Upgrade in a Pulp and Paper Mill  

E-Print Network [OSTI]

INVESTMENT-GRADE COMPRESSED AIR SYSTEM AUDIT, ANALYSIS, AND UPGRADE IN A PULP & PAPER MILL Paresh S. Parekh, P.E. Principal ABSTRACT An investment-grade compressed air audit, analysis, design, and upgrade in an industrial facility requires a..., West Tacoma Division, located in Washington State, had production capability of 540 tons per day of recycle newsprint manufactured from TMP and recycled paper. Over the years, as mill capacity increased, various sizes and types of air compressor...

Parekh, P. S.

7

Monitoring Infrastructure Capacity Monitoring Infrastructure Capacity  

E-Print Network [OSTI]

Levinson, D. (2000) Monitoring Infrastructure Capacity p. 165-181 in Land Market Monitoring for Smart Urban) task. Monitoring infrastructure capacity is at least as complex as monitoring urban land markets Levinson, D. (2000) Monitoring Infrastructure Capacity p. 165-181 in Land Market Monitoring for Smart Urban

Levinson, David M.

8

Two Milling Stone Inventories from Northern San Diego County, California  

E-Print Network [OSTI]

1982). Two Milling Stone Inventories from Northern San DiegoRincon 301. MILLING STONE INVENTORIES FROM SAN DIEGO COUNTYRincon 301. MILLING STONE INVENTORIES FROM SAN DIEGO COUNTY

True, D. L; Beemer, Eleanor

1982-01-01T23:59:59.000Z

9

Gas fluidized-bed stirred media mill  

DOE Patents [OSTI]

A gas fluidized-bed stirred media mill is provided for comminuting solid ticles. The mill includes a housing enclosing a porous fluidizing gas diffuser plate, a baffled rotor and stator, a hollow drive shaft with lateral vents, and baffled gas exhaust exit ports. In operation, fluidizing gas is forced through the mill, fluidizing the raw material and milling media. The rotating rotor, stator and milling media comminute the raw material to be ground. Small entrained particles may be carried from the mill by the gas through the exit ports when the particles reach a very fine size.

Sadler, III, Leon Y. (Tuscaloosa, AL)

1997-01-01T23:59:59.000Z

10

Design of a human powered maize mill  

E-Print Network [OSTI]

The process of milling corn into flour in many rural communities of East Africa has remained a traditional mortar and pestle process for centuries. Milling machines have failed in these communities largely due to poor ...

Salinas, Melvin Gustavo

2014-01-01T23:59:59.000Z

11

Standard Operating Procedure (SOP) -Milling Machine  

E-Print Network [OSTI]

Standard Operating Procedure (SOP) - Milling Machine · Keep all guards in place while operating the machine. · While operating the milling machine allow no one else to touch it. · Keep hands away from moving cutting tools. · Do not make measurements of the stock while the milling machine is powered. · Do

Veiga, Pedro Manuel Barbosa

12

Clean Air Act Requirements: Uranium Mill Tailings  

E-Print Network [OSTI]

EPA'S Clean Air Act Requirements: Uranium Mill Tailings Radon Emissions Rulemaking Reid J. Rosnick requirements for operating uranium mill tailings (Subpart W) Status update on Subpart W activities Outreach/Communications #12;3 EPA Regulatory Requirements for Operating Uranium Mill Tailings (Clean Air Act) · 40 CFR 61

13

URANIUM MILL TAILINGS RADON FLUX CALCULATIONS  

E-Print Network [OSTI]

URANIUM MILL TAILINGS RADON FLUX CALCULATIONS PIÃ?ON RIDGE PROJECT MONTROSE COUNTY, COLORADO Inc. (Golder) was commissioned by EFRC to evaluate the operations of the uranium mill tailings storage in this report were conducted using the WISE Uranium Mill Tailings Radon Flux Calculator, as updated on November

14

Welcome to Mills Memorial Library  

E-Print Network [OSTI]

-monthly) ­ online only #12;Journals defined · Journals are often "academic" or "scholarly" because the articles Books & Articles: Scholarly Information at Your Fingertips! Peggy Findlay Liaison Librarian Mills books 2. Databases: finding articles Questions? Any time during the session! #12;Before you start

Haykin, Simon

15

Mill Designed Bio bleaching Technologies  

SciTech Connect (OSTI)

A key finding of this research program was that Laccase Mediator Systems (LMS) treatments on high-kappa kraft could be successfully accomplished providing substantial delignification (i.e., > 50%) without detrimental impact on viscosity and significantly improved yield properties. The efficiency of the LMS was evident since most of the lignin from the pulp was removed in less than one hour at 45 degrees C. Of the mediators investigated, violuric acid was the most effective vis-a-vis delignification. A comparative study between oxygen delignification and violuric acid revealed that under relatively mild conditions, a single or a double LMS{sub VA} treatment is comparable to a single or a double O stage. Of great notability was the retention of end viscosity of LMS{sub VA} treated pulps with respect to the end viscosity of oxygen treated pulps. These pulps could then be bleached to full brightness values employing conventional ECF bleaching technologies and the final pulp physical properties were equal and/or better than those bleached in a conventional ECF manner employing an aggressively O or OO stage initially. Spectral analyses of residual lignins isolated after LMS treated high-kappa kraft pulps revealed that similar to HBT, VA and NHA preferentially attack phenolic lignin moieties. In addition, a substantial decrease in aliphatic hydroxyl groups was also noted, suggesting side chain oxidation. In all cases, an increase in carboxylic acid was observed. Of notable importance was the different selectivity of NHA, VA and HBT towards lignin functional groups, despite the common N-OH moiety. C-5 condensed phenolic lignin groups were overall resistant to an LMS{sub NHA, HBT} treatments but to a lesser extent to an LMS{sub VA}. The inactiveness of these condensed lignin moieties was not observed when low-kappa kraft pulps were biobleached, suggesting that the LMS chemistry is influenced by the extent of delignification. We have also demonstrated that the current generation of laccase has a broad spectrum of operating parameters. Nonetheless, the development of future genetically engineered laccases with enhanced temperature, pH and redox potentials will dramatically improve the overall process. A second challenge for LMS bleaching technologies is the need to develop effective, catalytic mediators. From the literature we already know this is feasible since ABTS and some inorganic mediators are catalytic. Unfortunately, the mediators that exhibit catalytic properties do not exhibit significant delignification properties and this is a challenge for future research studies. Potential short-term mill application of laccase has been recently reported by Felby132 and Chandra133 as they have demonstrated that the physical properties of linerboard can be improved when exposed to laccase without a chemical mediator. In addition, xxx has shown that the addition of laccase to the whitewater of the paper machine has several benefits for the removal of colloidal materials. Finally, this research program has presented important features on the delignification chemistry of LMS{sub NHA} and LMS{sub VA} that, in the opinion of the author, are momentous contributions to the overall LMS chemistry/biochemistry knowledge base which will continue to have future benefits.

Institute of Paper Science Technology

2004-01-30T23:59:59.000Z

16

LLaannggeerrhhaannss LLaabb PPrroottooccoollss Handling of Dead Fish at Yates Mill Facility  

E-Print Network [OSTI]

LLaannggeerrhhaannss LLaabb PPrroottooccoollss Handling of Dead Fish at Yates Mill Facility If a study fish is found dead, preserve it and return it to the lab for DRILL recording. If you are going to DCL shortly after finding the fish: 1. Put it in a plastic bag and bring it to DCL. 2. Put

Langerhans, Brian

17

World nuclear capacity and fuel cycle requirements, November 1993  

SciTech Connect (OSTI)

This analysis report presents the current status and projections of nuclear capacity, generation, and fuel cycle requirements for all countries in the world using nuclear power to generate electricity for commercial use. Long-term projections of US nuclear capacity, generation, fuel cycle requirements, and spent fuel discharges for three different scenarios through 2030 are provided in support of the Department of Energy`s activities pertaining to the Nuclear Waste Policy Act of 1982 (as amended in 1987). The projections of uranium requirements also support the Energy Information Administration`s annual report, Domestic Uranium Mining and Milling Industry: Viability Assessment.

Not Available

1993-11-30T23:59:59.000Z

18

ORISE: Capacity Building  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Capacity Building Because public health agencies must maintain the resources to respond to public health challenges, critical situations and emergencies, the Oak Ridge Institute...

19

Online SAG Mill Pluse Measurement and Optimization  

SciTech Connect (OSTI)

The grinding efficiency of semi autogenous milling or ball milling depends on the tumbling motion of the total charge within the mill. Utilization of this tumbling motion for efficient breakage of particles depends on the conditions inside the mill. However, any kind of monitoring device to measure the conditions inside the mill shell during operation is virtually impossible due to the severe environment presented by the tumbling charge. An instrumented grinding ball, which is capable of surviving a few hours and transmitting the impacts it experiences, is proposed here. The spectrum of impacts collected over 100 revolutions of the mills presents the signature of the grinding environment inside mill. This signature could be effectively used to optimize the milling performance by investigating this signature's relation to mill product size, mill throughput, make-up ball size, mill speed, liner profile and ball addition rates. At the same time, it can also be used to design balls and liner systems that can survive longer in the mill. The technological advances made in electronics and communication makes this leap in instrumentation certainly viable. Hence, the instrumented grinding ball offers the ability to qualitatively observe and optimize the milling environment. An instrumented load cell package that can measure the force of impacts inside the grinding chamber of a mill is developed here. The signal from the instrumented load cell package is interpreted in terms of a histogram termed as an impact spectrum which is a plot of the number of impacts at a specific energy level against the energy. It reflects on the average force regime of the mill. The instrumented load cell package was calibrated against the ultra fast load cell which has been unanimously accepted as a standard to measure single breakage events. The load cell package was successfully used to produce impact spectra in an 8.5 inch lab scale mill. The mill speed and the ball size were varied to study their effect on the impact spectra. A good correlation was found between the process variables and the impact spectra. The load cell package was then used in a 16 inch pilot scale mill. The mill speed, ball size, and mill filling were varied here and a consistent trend between these variables and impact spectra was observed. With a better understanding developed from the initial tests, the design of the load cell package was significantly changed to eliminate noise. With the new design, the impact spectra were re-determined in the 16 inch pilot mill varying the process variables - ball size, mill speed, and mill filling. Finally, it is successfully shown that a change in the operating variables of a mill can be seen in the impact spectra and that this concept can be successfully developed to monitor the grinding operation of industrial mills. To adapt it to industrial level it is mandatory to make the load cell package wireless. A design of a wireless circuit that is capable of transferring data at the required speed of 1000 kbps was also developed and tested at Cortez Gold Mines (CGM), Nevada.

Raj Rajamani; Jose Delgadillo; Vishal Duriseti

2007-06-30T23:59:59.000Z

20

Shaped Offset QPSK Capacity  

E-Print Network [OSTI]

In this work we compute the capacities and the pragmatic capacities of military-standard shaped-offset quadrature phase-shift keying (SOQPSK-MIL) and aeronautical telemetry SOQPSK (SOQPSK-TG). In the pragmatic approach, SOQPSK is treated as a...

Sahin, Cenk

2012-08-31T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Liquid heat capacity lasers  

DOE Patents [OSTI]

The heat capacity laser concept is extended to systems in which the heat capacity lasing media is a liquid. The laser active liquid is circulated from a reservoir (where the bulk of the media and hence waste heat resides) through a channel so configured for both optical pumping of the media for gain and for light amplification from the resulting gain.

Comaskey, Brian J. (Walnut Creek, CA); Scheibner, Karl F. (Tracy, CA); Ault, Earl R. (Livermore, CA)

2007-05-01T23:59:59.000Z

22

The Misplaced Role of “Utilitarianism” in John Stuart Mill’s Utilitarianism  

E-Print Network [OSTI]

This thesis aims to provide the appropriate historical context for interpreting John Stuart Mill's Utilitarianism. The central question considered here concerns two views of Mill's intentions for Utilitarianism, and whether the work should be read...

Wright, David

2012-10-19T23:59:59.000Z

23

The Bowersock Mills and Power Company 1874  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Incremental Hydroelectric Energy The Bowersock Mills and Power Co., Lawrence, KS Hydroelectric Energy Potential for U.S. BMPC Plant At Forefront of Development Curve "In our...

24

Welcome to Cotton Mills At Cotton Mills, we believe your accommodation should help you make the most of your  

E-Print Network [OSTI]

Welcome to Cotton Mills At Cotton Mills, we believe your accommodation should help you make to an amazing £1,200 per annum. Cotton Mills is fully certificated by: Cotton Mills is fully certificated. Cotton Mills is conveniently located on Radford Boulevard, right next to Norton Court (NTU accommodation

Evans, Paul

25

Virtual cutter path display for dental milling machine  

E-Print Network [OSTI]

This paper presents the prototype of a mixed reality system using the computer controlled dental milling machine, which is called MRD Mill. First, overview of the core dental milling machine developed in this study is ...

Ito, Teruaki

26

Forward capacity market CONEfusion  

SciTech Connect (OSTI)

In ISO New England and PJM it was assumed that sponsors of new capacity projects would offer them into the newly established forward centralized capacity markets at prices based on their levelized net cost of new entry, or ''Net CONE.'' But the FCCMs have not operated in the way their proponents had expected. To clear up the CONEfusion, FCCM designs should be reconsidered to adapt them to the changing circumstances and to be grounded in realistic expectations of market conduct. (author)

Wilson, James F.

2010-11-15T23:59:59.000Z

27

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity

28

Radiological health aspects of uranium milling  

SciTech Connect (OSTI)

This report describes the operation of conventional and unconventional uranium milling processes, the potential for occupational exposure to ionizing radiation at the mill, methods for radiological safety, methods of evaluating occupational radiation exposures, and current government regulations for protecting workers and ensuring that standards for radiation protection are adhered to. In addition, a survey of current radiological health practices is summarized.

Fisher, D.R.; Stoetzel, G.A.

1983-05-01T23:59:59.000Z

29

Mill Town, Factory Town, Cultural Economic Engine  

E-Print Network [OSTI]

Mill Town, Factory Town, Cultural Economic Engine: North Adams in Context Kay Oehler Stephen of a contemporary art museum, while a seemingly improbable choice at the time for an `economic engine', has in fact Sheppard Blair Benjamin C3 D Report NA1.2006 Copyright 2006 #12;Mill Town, Factory Town, Cultural Economic

Stoiciu, Mihai

30

short-wood and is also character-ized by large payloads and long  

E-Print Network [OSTI]

short-wood and is also character- ized by large payloads and long distances. However, due to our- mately 90% of wood arrives at mills by truck, with 10% arriving through a combination of water and rail. Of the roundwood deliv- ery, approximately 93% is in long- wood form, with the small remain- der being short-wood

Bolding, M. Chad

31

Dual capacity reciprocating compressor  

DOE Patents [OSTI]

A multi-cylinder compressor particularly useful in connection with northern climate heat pumps and in which different capacities are available in accordance with reversing motor rotation is provided with an eccentric cam on a crank pin under a fraction of the connecting rods, and arranged for rotation upon the crank pin between opposite positions 180[degree] apart so that with cam rotation on the crank pin such that the crank throw is at its normal maximum value all pistons pump at full capacity, and with rotation of the crank shaft in the opposite direction the cam moves to a circumferential position on the crank pin such that the overall crank throw is zero. Pistons whose connecting rods ride on a crank pin without a cam pump their normal rate with either crank rotational direction. Thus a small clearance volume is provided for any piston that moves when in either capacity mode of operation. 6 figs.

Wolfe, R.W.

1984-10-30T23:59:59.000Z

32

Dual capacity reciprocating compressor  

DOE Patents [OSTI]

A multi-cylinder compressor 10 particularly useful in connection with northern climate heat pumps and in which different capacities are available in accordance with reversing motor 16 rotation is provided with an eccentric cam 38 on a crank pin 34 under a fraction of the connecting rods, and arranged for rotation upon the crank pin between opposite positions 180.degree. apart so that with cam rotation on the crank pin such that the crank throw is at its normal maximum value all pistons pump at full capacity, and with rotation of the crank shaft in the opposite direction the cam moves to a circumferential position on the crank pin such that the overall crank throw is zero. Pistons 24 whose connecting rods 30 ride on a crank pin 36 without a cam pump their normal rate with either crank rotational direction. Thus a small clearance volume is provided for any piston that moves when in either capacity mode of operation.

Wolfe, Robert W. (Wilkinsburg, PA)

1984-01-01T23:59:59.000Z

33

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity Report June 2014

34

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity Report June

35

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity Report

36

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity Report Operable

37

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity Report

38

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity Reportof Last

39

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity Reportof

40

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1Capacity ReportofVacuum

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1CapacityCORPORATION /

42

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1CapacityCORPORATION

43

Remediation of inactive mining and milling sites  

SciTech Connect (OSTI)

The presentation introduces relevant environment remediation standards and describes some measures of engineering remedied for inactive mines and mills. Since 1990, the remediation of decommissioned nuclear facilities has obtained fixed financial aid from state government, part of which is offered to inactive mines and mills. Considering the environmental characteristics of Chinese uranium mines and mills, the major task of decommissioning is to prevent radon release, and keep surface water and underground water from contamination. In order to control the rate of radon release effectively, the authors` research institutes conducted a series of experiments on the covers of tailings with two kinds of different material, clay and concrete.

Mao, H.; Pan, Y.; Li, R.

1993-12-31T23:59:59.000Z

44

Control of the Accumulation of Non-Process Elements in Pulp Mills with Bleach Filtrate Reuse: A Chemical Equilibrium Approach to Predicting the Partitioning of Metals in Pulp Mill and Bleach Plant Streams  

SciTech Connect (OSTI)

The overall goal of this project was to develop fundamental, experimentally based methods for predicting the solubility or organic and inorganic matter and their interactions in recycled effluent from kraft pulp mills and bleach plants. This included: characterizing the capacity of wood pulp and dissolved organic matter to bind metal ions, developing a thermodynamic database of properties needed to describe the solubility of inorganic matter in pulp mill streams, incorporation of the database into equilibrium calculation software for predicting the solubility of the metals of interest, and evaluating its capability to predict the distribution of the metals between pulp fibers, inorganic precipitates, and solution.

Frederick, W.J. Jr.; Rudie, A.W.; Schmidl, G.W.; Sinquefield, S.A.; Rorrer, G.L.; Laver, M.L.; Yantasee, W.; Ming, D.

2000-08-01T23:59:59.000Z

45

Capacity Value of Solar Power  

SciTech Connect (OSTI)

Evaluating the capacity value of renewable energy sources can pose significant challenges due to their variable and uncertain nature. In this paper the capacity value of solar power is investigated. Solar capacity value metrics and their associated calculation methodologies are reviewed and several solar capacity studies are summarized. The differences between wind and solar power are examined, the economic importance of solar capacity value is discussed and other assessments and recommendations are presented.

Duignan, Roisin; Dent, Chris; Mills, Andrew; Samaan, Nader A.; Milligan, Michael; Keane, Andrew; O'Malley, Mark

2012-11-10T23:59:59.000Z

46

Advanced Oxidation Technology for Pulp Mill Effluent  

E-Print Network [OSTI]

ADVANCED OXIDATION TECHNOLOGY FOR PULP MILL EFFLUENT J. ROBERT HART, MANAGER, EPRI PULP & PAPER OFFICE, ATLANTA, GA ABSTRACT The composition of effluent from various pulping processes can exhibit a wide range of physical and chemical... in Integrated Pulp and Paper Mill Effluents", 1992 169 ESL-IE-92-04-30 Proceedings from the 14th National Industrial Energy Technology Conference, Houston, TX, April 22-23, 1992 ...

Hart, J. R.

47

China ups ethylene capacity  

SciTech Connect (OSTI)

China is continuing with plans to build up its petrochemical sector. Following government approval the Dongying petrochemical complex in Shandong province is expected to get under way early next year. It will be based on a 140,000-m.t./year ethylene plant and will be the second-largest petrochemical complex in the province, after Qilu, about 50 km away. In addition, there are plans to expand capacities of existing ethylene plants. The Dongying complex will be owned by Shengli Oil Field (50%). Shandong province (35%), and the Dongying municipality (15%). Downstream capacities will comprise 80,000 m.t./year of linear low-density polyethylene (LLDPE) and 20,000 m.t./year of high-density PE. Butene-1 to be used as comonomer for LLDPE will be shipped from Qilu.

Alperowicz, N.; Wood, A.

1992-12-23T23:59:59.000Z

48

ORISE: Capacity Building  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas Conchas recoveryLaboratory |CHEMPACK Mapping Application ORISE developsRelatedCapacity

49

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on theThousand7.End1

50

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on

51

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on Cokers Catalytic Crackers Hydrocrackers

52

Refinery Capacity Report  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in NonproducingAdditions to Capacity on Cokers Catalytic Crackers

53

Final environmental statement related to the Western Nuclear, Inc. , Split Rock Uranium Mill (Fremont County, Wyoming)  

SciTech Connect (OSTI)

The proposed action is the renewal of Source Material License SUA-56 (with amendments) issued to Western Nuclear, Inc. (WNI), for the operation of the Split Rock Uranium Mill near Jeffrey City and the Green Mountain Ion-Exchange Facility, both in Fremont County, Wyoming. The license also permits possession of material from past operations at four ancillary facilities in the Gas Hills mining area - the Bullrush, Day-Loma, Frazier-Lamac, and Rox sites (Docket No. 40-1162). However, although heap leaching operations were previously authorized at Frazier-Lamac, there has never been any processing of material at this site. The Split Rock mill is an acid-leach, ion-exchange and solvent-extraction uranium-ore processing mill with a design capacity of 1540 MT (1700 tons) of ore per day. WNI has proposed by license amendment request to increase the storage capacity of the tailings ponds in order to permit the continuation of present production rates of U/sub 3/O/sub 8/ through 1996 using lower-grade ores.

Not Available

1980-02-01T23:59:59.000Z

54

WINDExchange: Wind Potential Capacity  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLasDelivered energy consumption byAbout Printable Version Bookmark and Wind Potential Capacity

55

Radionuclides in the terrestrial ecosystem near a Canadian uranium mill -- Part 1: Distribution and doses  

SciTech Connect (OSTI)

Soils, vegetation, small mammals, and birds were measured for uranium series radionuclides at three sites near the operating Key Lake uranium mill in northern Saskatchewan. Sites, impacted by windblown tailings and mill dust, had significantly higher concentrations of uranium, {sup 226}Ra, {sup 210}Pb, and {sup 210}Po in soils, litter, vegetation, tree needles and twigs, small mammals, and birds, compared to a control site. Samples were collected from both upland jackpine and black spruce bog habitats in triplicate at each site. Both habitats were similar in radionuclide accumulation. Absorbed doses averaged 0.92, 8.4, and 4.9 mGy y{sup {minus}1} to small mammals and 2.0, 5.8, and 2.8 mGy y{sup {minus}1} to Lincoln's sparrows at the control, tailings, and mill sites, respectively. These doses do not include doses from short-lived radon progeny. The majority of the dose increment at the tailings and mill sites was due to {sup 226}Ra, whereas it was {sup 210}Po at the control site. Thus, use of a radiation weighting factor of 20 for alpha radiation raised equivalent doses (in mSv y{sup {minus}1}) by nearly a factor of 20.

Thomas, P.A.

2000-06-01T23:59:59.000Z

56

Transportation of the MOAB Uranium Mill Tailings to White Mesa Mill by Slurry Pipeline  

SciTech Connect (OSTI)

The Moab uranium mill tailings pile, located at the former Atlas Minerals Corporation site approximately three miles north of Moab, Utah, is now under the control of the US Department of Energy (''DOE''). The location of the tailings pile adjacent to the Colorado River, and the ongoing contamination of groundwater and seepage of pollutants into the river, have lead to the investigation, as part of the final site remediation program, of alternatives to relocate the tailings to a qualified permanent disposal site. This paper will describe the approach being taken by the team formed between International Uranium (USA) Corporation (''IUC'') and Washington Group International (''WGINT'') to develop an innovative technical proposal to relocate the Moab tailings to IUC's White Mesa Mill south of Blanding, Utah. The proposed approach for relocating the tailings involves using a slurry pipeline to transport the tailings to the White Mesa Mill. The White Mesa Mill is a fully licensed, active uranium mill site that is uniquely suited for permanent disposal of the Moab tailings. The tailings slurry would be dewatered at the White Mesa Mill, the slurry water would be recycled to the Moab site for reuse in slurry makeup, and the ''dry'' tailings would be permanently disposed of in an approved below grade cell at the mill site.

Hochstein, R. F.; Warner, R.; Wetz, T. V.

2003-02-26T23:59:59.000Z

57

Milling Machine Replacement Project (4587), 5/11/2012  

Broader source: Energy.gov (indexed) [DOE]

by E-mail The proposed action is to replace two large milling machines with two new medium sized CNC milling machines. The new machines will be connected to the digital...

58

MANAGING SHORT-LIFECYCLE TECHNOLOGY PRODUCTS FOR AGERE S. David Wu  

E-Print Network [OSTI]

characterization tools for capacity planning and capacity negotiation with their global supply partners with correlation values ranging from 0.51 to 0.95. These findings have significant implications to capacity classification: 1. An Overview of Short-Lifecycle Technology Markets In the mid to late 1990's, high- tech

Wu, David

59

Original article Impact of spreading olive mill wastewater on soil  

E-Print Network [OSTI]

Original article Impact of spreading olive mill wastewater on soil characteristics: laboratory 2001) Abstract ­ A dynamic of soil pollution with olive mill wastewater (OMW) was investigated process forms an olive mill wastewater (OMW). The amount of this waste depends on the process used for oil

Paris-Sud XI, Université de

60

The effect of conditioning rice during the laboratory milling process on the quality of the milled sample  

E-Print Network [OSTI]

THE EFFECT OF CONDITIONING RICE DURING THE LABORATORY MILLING PROCESS ON THE QUALITY OF THE MILLED SAMPLE A Thesis by ROY EUGENE CHILDERS, JR. Submitted to the Graduate College of Texas A8M University in partial fulfillment... of the requirement for the degree of MASTER OF SCIENCE August 1972 Major Subject: Agricultural Engineering THE EFFECT OF CONDITIONING RICE DURING THE LABORATORY MILLING PROCESS ON THE I1UALITY OF THE MILLED SAMPLE A Thesis by ROY EUGENE CHILDERS, JR...

Childers, Roy Eugene

1972-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Kieffer Paper Mill's Recycled Fiber Mill and PSI Energy's High Efficiency Motors Plan  

E-Print Network [OSTI]

efficiency would yield significant energy savings. PSI Energy was able to help Kieffer examine the economics of high efficiency motors, and through the PSI Energy High Efficiency Motors Plan encouraged Kieffer Paper Mills to purchase energy efficient motors...

Myers, J. A.

62

Loop expansion in Yang-Mills thermodynamics  

E-Print Network [OSTI]

We argue that a selfconsistent spatial coarse-graining, which involves interacting (anti)calorons of unit topological charge modulus, implies that real-time loop expansions of thermodynamical quantities in the deconfining phase of SU(2) and SU(3) Yang-Mills thermodynamics are, modulo 1PI resummations, determined by a finite number of connected bubble diagrams.

Ralf Hofmann

2009-11-05T23:59:59.000Z

63

Wind Mill Pattern Optimization using Evolutionary Algorithms  

E-Print Network [OSTI]

Wind Mill Pattern Optimization using Evolutionary Algorithms Charlie Vanaret ENAC , IRIT 7 av Ed 31062 Toulouse Cedex 9, France jean-marc.alliot@irit.fr ABSTRACT When designing a wind farm layout, we a grid, we can gain up to 3% of energy output on simple exam- ples of wind farms dealing with many

64

Short Communication Bioreduction and precipitation of uranium in ionic liquid aqueous  

E-Print Network [OSTI]

with uranium from mining and milling operations, radioactive wastes, and from nuclear accidents is a majorShort Communication Bioreduction and precipitation of uranium in ionic liquid aqueous solution t s Uranium forms various complexes with ionic liquids. Uranium bioreduction was affected by the type

Ohta, Shigemi

65

Beneficial uses of paper mill residuals for New York State`s recycled-paper mills. Final report  

SciTech Connect (OSTI)

This report evaluates the New York paper mill industry in terms of the productive management and treatment of solid wastes. It identifies current efforts by recycling mills to beneficially use paper mill residuals (often called sludge) and suggests additional options that should be considered by the industry in general and individual mills in particular. It also examines the regulations and economics affecting the mills and suggests actions that could improve the industry`s ability to convert wastes to value-added products. The report recommends that the mills should continue measures to reduce fiber and filler clay losses, promote the transfer of usable fiber and clay to mills able to use them, upgrade sludge dewatering capabilities, and take a more regional approach to solid waste disposal problems. State agencies are urged to support these efforts, encourage the development and commercialization of new beneficial use technologies, and reduce regulatory barriers whenever possible.

NONE

1995-09-01T23:59:59.000Z

66

On the amorphization behavior and hydrogenation performance of high-energy ball-milled Mg{sub 2}Ni alloys  

SciTech Connect (OSTI)

Amorphous Mg{sub 2}Ni alloy was prepared by high energy ball-milling starting with polycrystalline Mg{sub 2}Ni which was prepared with the help of a metallurgy method by using a SPEX 8000D mill. The microstructural and phase structure characterization of the prepared materials was performed via scanning electron microscopy, transition electron microscope and X-ray diffraction. The thermal stabilities were investigated by differential scanning calorimetry. The apparent activation energies were determined by means of the Kissinger method. The first and second crystallization reactions take place at ? 255 °C and ? 410 °C, and the corresponding activation energy of crystallization is E{sub a1} = 276.9 and E{sub a2} = 382.4 kJ/mol, respectively. At 3 MPa hydrogen pressure and 250 °C, the hydrogen absorption capacities of crystalline, partially and fully amorphous Mg{sub 2}Ni alloy are 2.0 wt.%, 3.2 wt.% and 3.5 wt.% within 30 min, respectively. - Graphical Abstract: We mainly focus on the amorphization behavior of crystalline Mg{sub 2}Ni alloy in the high energy ball-milling process and the crystallization behavior of the amorphous Mg{sub 2}Ni alloy in a follow-up heating process. The relationship of milling, microstructure and hydrogenation properties is established and explained by models. - Highlights: • Amorphous Mg{sub 2}Ni has been obtained by high energy ball milling the as-cast alloy. • The amorphization behavior of polycrystalline Mg{sub 2}Ni is presented. • The crystallization behavior of the amorphous Mg{sub 2}Ni alloy is illustrated. • Establish the relationship of milling, microstructure and hydrogenation properties.

Kou, Hongchao; Hou, Xiaojiang; Zhang, Tiebang, E-mail: tiebangzhang@nwpu.edu.cn; Hu, Rui; Li, Jinshan; Xue, Xiangyi

2013-06-15T23:59:59.000Z

67

Geothermal Mill Redevelopment Project in Massachusetts  

SciTech Connect (OSTI)

Anwelt Heritage Apartments, LLC redeveloped a 120-year old mill complex into a mixed-use development in a lower-income neighborhood in Fitchburg, Massachusetts. Construction included 84 residential apartments rented as affordable housing to persons aged 62 and older. The Department of Energy (“DOE”) award was used as an essential component of financing the project to include the design and installation of a 200 ton geothermal system for space heating and cooling.

Vale, A.Q.

2009-03-17T23:59:59.000Z

68

Mills, Wyoming: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 -Energieprojekte GmbH JumpSprings, Vermont:isMillersport,Mills County,

69

Environmental assessment of remedial action at the Gunnison Uranium Mill Tailings Site, Gunnison, Colorado. [UMTRA Project  

SciTech Connect (OSTI)

This document assesses and compares the environmental impacts of various alternatives for remedial action at the Gunnison uranium of mill tailings site located 0.5 miles south of Gunnison, Colorado. The site covers 56 acres and contains 35 acres of tailings, 2 of the original mill buildings and a water tower. The Uranium Mill Tailings Radiation Control of Act of 1978 (UMTRCA), Public Law 95-604, authorizes the US Department of Energy to clean up the site to reduce the potential health impacts associated with the residual radioactive materials remaining at the site and at associated (vicinity) properties off the site. The US Environmental Protection Agency promulgated standards for the remedial actions (40 CFR 192). Remedial actions must be performed in accordance with these standards and with the occurrence of the Nuclear Regulatory Commission. Four alternatives have been addressed in this document. The first alternative is to consolidate the tailings and associated contaminated soils into a recontoured pile on the southern portion of the existing site. A radon barrier of silty clay would be constructed over the pile and various erosion control measures would be taken to assure the long-term integrity of the pile. Two other alternatives which involve moving the tailings to new locations are assessed in this document. These alternatives generally involve greater short-term impacts and are more costly but would result in the tailings being stabilized in a location farther from the city of Gunnison. The no action alternative is also assessed.

Bachrach, A.; Hoopes, J.; Morycz, D. (Jacobs Engineering Group, Inc., Pasadena, CA (USA)); Bone, M.; Cox, S.; Jones, D.; Lechel, D.; Meyer, C.; Nelson, M.; Peel, R.; Portillo, R.; Rogers, L.; Taber, B.; Zelle, P. (Weston (Roy F.), Inc., Washington, DC (USA)); Rice, G. (Sergent, Hauskins and Beckwith (USA))

1984-12-01T23:59:59.000Z

70

HIGH-CAPACITY POLYANION CATHODES  

Broader source: Energy.gov (indexed) [DOE]

FY12 - 280K * Funding for FY13 - 280K *Funding for FY14 - 280K Barriers * Barriers - Cost - Cycle life - Energy and power densities * Targets - High-capacity and high-voltage...

71

John Stuart Mill's Sanction Utilitarianism: A Philosophical and Historical Interpretation  

E-Print Network [OSTI]

..................................................................................................... 271 1 CHAPTER I INTRODUCTION This dissertation will argue that John Stuart Mill (hereafter Mill) is best interpreted as a sanction utilitarian. To support this claim, I will provide arguments that that are both philosophical... Utilitarianism. Third, I will outline the dissertation as a whole in order to describe how each chapter supports the claim that Mill is best interpreted as a sanction utilitarian. Basic terminology and the varieties of utilitarianism As is common...

Wright, David

2014-04-24T23:59:59.000Z

72

attritor mill fy06: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

International Zernicka-Goetz, Magdalena 46 Clean Air Act Requirements: Uranium Mill Tailings Environmental Sciences and Ecology Websites Summary: :www.epa.govradiation...

73

americana mill var: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

International Zernicka-Goetz, Magdalena 110 Clean Air Act Requirements: Uranium Mill Tailings Environmental Sciences and Ecology Websites Summary: :www.epa.govradiation...

74

americana mill sobre: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

International Zernicka-Goetz, Magdalena 64 Clean Air Act Requirements: Uranium Mill Tailings Environmental Sciences and Ecology Websites Summary: :www.epa.govradiation...

75

Exterior Differential Systems for Yang-Mills Theories  

E-Print Network [OSTI]

Exterior differential systems are given, and their Cartan characters calculated, for Maxwell and SU(2)-Yang-Mills equations in dimensions from three to six.

Frank B. Estabrook

2008-12-05T23:59:59.000Z

76

Investment Timing and Capacity Choice for Small-Scale Wind PowerUnder Uncertainty  

SciTech Connect (OSTI)

This paper presents a method for evaluation of investments in small-scale wind power under uncertainty. It is assumed that the price of electricity is uncertain and that an owner of a property with wind resources has a deferrable opportunity to invest in one wind power turbine within a capacity range. The model evaluates investment in a set of projects with different capacity. It is assumed that the owner substitutes own electricity load with electricity from the wind mill and sells excess electricity back to the grid on an hourly basis. The problem for the owner is to find the price levels at which it is optimal to invest, and in which capacity to invest. The results suggests it is optimal to wait for significantly higher prices than the net present value break-even. Optimal scale and timing depend on the expected price growth rate and the uncertainty in the future prices.

Fleten, Stein-Erik; Maribu, Karl Magnus

2004-11-28T23:59:59.000Z

77

Engineering assessment of inactive uranium mill tailings  

SciTech Connect (OSTI)

The Grand Junction site has been reevaluated in order to revise the October 1977 engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Grand Junction, Colorado. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the 1.9 million tons of tailings at the Grand Junction site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The eight alternative actions presented herein range from millsite and off-site decontamination with the addition of 3 m of stabilization cover material (Option I), to removal of the tailings to remote disposal sites and decontamination of the tailings site (Options II through VIII). Cost estimates for the eight options range from about $10,200,000 for stabilization in-place to about $39,500,000 for disposal in the DeBeque area, at a distance of about 35 mi, using transportation by rail. If transportation to DeBeque were by truck, the cost estimated to be about $41,900,000. Three principal alternatives for the reprocessing of the Grand Junction tailings were examined: (a) heap leaching; (b) treatment at an existing mill; and (c) reprocessing at a new conventional mill constructed for tailings reprocessing. The cost of the uranium recovered would be about $200/lb by heap leach and $150/lb by conventional plant processes. The spot market price for uranium was $25/lb early in 1981. Therefore, reprocessing the tailings for uranium recovery appears not to be economically attractive.

Not Available

1981-07-01T23:59:59.000Z

78

Colony Mills Limited | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin:EnergyWisconsin: Energy,(EC-LEDS) | Open EnergyColony Mills Limited Jump to:

79

Computing Three-Point Functions for Short Operators  

E-Print Network [OSTI]

We compute the three-point structure constants for short primary operators of N=4 super Yang-Mills theory to leading order in the inverse coupling by mapping the problem to a flat-space string theory calculation. We check the validity of our procedure by comparing to known results for three chiral primaries. We then compute the three-point functions for any combination of chiral and non-chiral primaries, with the non-chiral primaries all dual to string states at the first massive level. Along the way we find many cancellations that leave us with simple expressions, suggesting that integrability is playing an important role.

Till Bargheer; Joseph A. Minahan; Raul Pereira

2014-04-14T23:59:59.000Z

80

Hybrid Zero-capacity Channels  

E-Print Network [OSTI]

There are only two known kinds of zero-capacity channels. The first kind produces entangled states that have positive partial transpose, and the second one - states that are cloneable. We consider the family of 'hybrid' quantum channels, which lies in the intersection of the above classes of channels and investigate its properties. It gives rise to the first explicit examples of the channels, which create bound entangled states that have the property of being cloneable to the arbitrary finite number of parties. Hybrid channels provide the first example of highly cloneable binding entanglement channels, for which known superactivation protocols must fail - superactivation is the effect where two channels each with zero quantum capacity having positive capacity when used together. We give two methods to construct a hybrid channel from any binding entanglement channel. We also find the low-dimensional counterparts of hybrid states - bipartite qubit states which are extendible and possess two-way key.

Sergii Strelchuk; Jonathan Oppenheim

2012-07-04T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Capture and Sequestration of CO2 at the Boise White Paper Mill  

SciTech Connect (OSTI)

This report documents the efforts taken to develop a preliminary design for the first commercial-scale CO2 capture and sequestration (CCS) project associated with biomass power integrated into a pulp and paper operation. The Boise Wallula paper mill is located near the township of Wallula in Southeastern Washington State. Infrastructure at the paper mill will be upgraded such that current steam needs and a significant portion of the current mill electric power are supplied from a 100% biomass power source. A new biomass power system will be constructed with an integrated amine-based CO2 capture plant to capture approximately 550,000 tons of CO2 per year for geologic sequestration. A customized version of Fluor Corporation’s Econamine Plus™ carbon capture technology will be designed to accommodate the specific chemical composition of exhaust gases from the biomass boiler. Due to the use of biomass for fuel, employing CCS technology represents a unique opportunity to generate a net negative carbon emissions footprint, which on an equivalent emissions reduction basis is 1.8X greater than from equivalent fossil fuel sources (SPATH and MANN, 2004). Furthermore, the proposed project will offset a significant amount of current natural gas use at the mill, equating to an additional 200,000 tons of avoided CO2 emissions. Hence, the total net emissions avoided through this project equates to 1,100,000 tons of CO2 per year. Successful execution of this project will provide a clear path forward for similar kinds of emissions reduction that can be replicated at other energy-intensive industrial facilities where the geology is suitable for sequestration. This project also represents a first opportunity for commercial development of geologic storage of CO2 in deep flood basalt formations. The Boise paper mill site is host to a Phase II pilot study being carried out under DOE’s Regional Carbon Partnership Program. Lessons learned from this pilot study and other separately funded projects studying CO2 sequestration in basalts will be heavily leveraged in developing a suitable site characterization program and system design for permanent sequestration of captured CO2. The areal extent, very large thickness, high permeability in portions of the flows, and presence of multiple very low permeability flow interior seals combine to produce a robust sequestration target. Moreover, basalt formations are quite reactive with water-rich supercritical CO2 and formation water that contains dissolved CO2 to generate carbonate minerals, providing for long-term assurance of permanent sequestration. Sub-basalt sediments also exist at the site providing alternative or supplemental storage capacity.

B.P. McGrail; C.J. Freeman; G.H. Beeman; E.C. Sullivan; S.K. Wurstner; C.F. Brown; R.D. Garber; D. Tobin E.J. Steffensen; S. Reddy; J.P. Gilmartin

2010-06-16T23:59:59.000Z

82

Rapid nutrient determination of sugarcane milling by-products using near infrared spectroscopy.  

E-Print Network [OSTI]

??This thesis investigates the use of near infrared (NIR) spectroscopic methods for rapid measurement of nutrient elements in mill mud and mill ash. Adoption of… (more)

Keeffe, Eloise Caitlin

2013-01-01T23:59:59.000Z

83

Grinding media oscillation: effect on torsional vibrations in tumble mills  

E-Print Network [OSTI]

of oscillation of grinding media on torsional vibrations of the mill. A theoretical model was developed to determine the oscillating frequency of the grinding media. A 12" (0.3 m) diameter tumble mill test rig was built with a 0.5 hp DC motor. The rig is tested...

Toram, Kiran Kumar

2005-11-01T23:59:59.000Z

84

Uranium Mill Tailings Remedial Action Project surface project management plan  

SciTech Connect (OSTI)

This Project Management Plan describes the planning, systems, and organization that shall be used to manage the Uranium Mill Tailings Remedial Action Project (UMTRA). US DOE is authorized to stabilize and control surface tailings and ground water contamination at 24 inactive uranium processing sites and associated vicinity properties containing uranium mill tailings and related residual radioactive materials.

Not Available

1994-09-01T23:59:59.000Z

85

Tons of Heavy Metals in Mill Creek Sediments Heather Freeman  

E-Print Network [OSTI]

objectives for this summer research were to: 1.) determine how much heavy metal pollution has accumulatedTons of Heavy Metals in Mill Creek Sediments Heather Freeman 8/30/99 Geology Department Advisors: Dr. Kees DeJong Dr. Barry Manyard Dr. David Nash #12;Tons of heavy metals in Mill Creek sediments

Maynard, J. Barry

86

An analysis of mobile feed milling operations in Texas  

E-Print Network [OSTI]

or lf it is inoperative due to repairs. We operator who owned twc mobilss vas considering the pxacticality of removing one of the rills frvz its truck chasis and operating it as a stationary mill at his feed store, Another operator operates his mill...

Cunningham, William Carroll

1962-01-01T23:59:59.000Z

87

Kampung Capacity Local Solutions for  

E-Print Network [OSTI]

Kampung Capacity Local Solutions for Sustainable Rural Energy in the Baram River Basin, Sarawak with a large-scale hydropower plan for the river basin. Keywords: South East Asia, Malaysia, Rural Energy In this study we explore the potential for rural renewable energy supply through a focus on villages

Kammen, Daniel M.

88

Capacity Allocation with Competitive Retailers Masabumi Furuhata  

E-Print Network [OSTI]

to uncertainty of market demands, costly capacity construction and time consuming capacity expansion. This makes the market to be unstable and malfunc- tioning. Such a problem is known as the capacity allocation investigate the properties of capacity allocation mechanisms for the markets where a sin- gle supplier

Zhang, Dongmo

89

A thick homogeneous vegetated cover design proves cost - and schedule-effective for the reclamation of uranium mills sites near Spokane, Washington  

SciTech Connect (OSTI)

The Washington State Department of Health (WDOH) has licensed two medium sized uranium mills with tailings impoundments covering 28 and 40 hectares (70 and 100 acres), respectively, The uranium mill licensees have submitted closure and reclamation plans to the state, and site-specific conditions have determined the closure design features, Conventional uranium mill cover designs usually incorporate an overall cap of one to three meters, which includes a low-permeability clay barrier layer. A technical evaluation of several uranium mill facilities that used this design was published in the fall of 1994 and reported that unexpected vegetation root damage had occurred in the low-permeability clay (or bentonite amended) barrier layers. The technical report suggested that the low-permeability design feature at some sites could be compromised within a very short time and the regulatory goal of 1,000 years performance might not be achieved. In October 1994, WDOH sponsored a technical forum meeting to consider design alternatives to address these reliability concerns. Representatives from the federal government, nuclear industry, licensees, engineering firms, and state regulatory agencies attended the workshop. Risk factors considered in the evaluation of the uranium mill reclamation plans include: (1) radon gas emanation through the cover (the air pathway), and (2) migration of hazardous and/or radioactive constituents (the groundwater pathway). Additional design considerations include site structural stability, longevity of 1,000 years, and no active (ongoing) maintenance. 9 refs.

Blacklaw, J.; Robertson, G.; Stoffel, D.; Ahmad, J.; Fordham, E. [Washington State Dept. of Health, Olympia, WA (United States)] [and others

1997-08-01T23:59:59.000Z

90

High capacity immobilized amine sorbents  

DOE Patents [OSTI]

A method is provided for making low-cost CO.sub.2 sorbents that can be used in large-scale gas-solid processes. The improved method entails treating an amine to increase the number of secondary amine groups and impregnating the amine in a porous solid support. The method increases the CO.sub.2 capture capacity and decreases the cost of utilizing an amine-enriched solid sorbent in CO.sub.2 capture systems.

Gray, McMahan L. (Pittsburgh, PA); Champagne, Kenneth J. (Fredericktown, PA); Soong, Yee (Monroeville, PA); Filburn, Thomas (Granby, CT)

2007-10-30T23:59:59.000Z

91

Controlling a Steel Mill with BOXES Michael McGarity, Claude Sammut and David Clements  

E-Print Network [OSTI]

Controlling a Steel Mill with BOXES Michael McGarity, Claude Sammut and David Clements and Chambers (1968) to a large-scale, real-world problem, namely, learning to control a steel mill. By applying BOXES to a model of a skinpass mill (a type of steel mill), we find that the BOXES algorithm can be made

Sammut, Claude

92

Short wavelength laser  

DOE Patents [OSTI]

A short wavelength laser is provided that is driven by conventional-laser pulses. A multiplicity of panels, mounted on substrates, are supported in two separated and alternately staggered facing and parallel arrays disposed along an approximately linear path. When the panels are illuminated by the conventional-laser pulses, single pass EUV or soft x-ray laser pulses are produced.

Hagelstein, P.L.

1984-06-25T23:59:59.000Z

93

Determination of aerosol size distributions at uranium mill tailings remedial action project sites  

SciTech Connect (OSTI)

The U.S. Department of Energy (DOE) has an ongoing program, the Uranium Mill Tailings Remedial Action (UMTRA) Project, to stabilize piles of uranium mill tailings in order to reduce the potential radiological hazards to the public. Protection of workers and the general public against airborne radioactivity during remedial action is a top priority at the UMTRA Project. The primary occupational radionuclides of concern are {sup 230}Th, {sup 226}Ra, {sup 210}Pb, {sup 210}Po, and the short-lived decay products of {sup 222}Rn with {sup 230}Th causing the majority of the committed effective dose equivalent (CEDE) from inhaling uranium mill tailings. Prior to this study, a default particle size of 1.0 {mu}m activity median aerodynamic diameter (AMAD) was assumed for airborne radioactive tailings dust. Because of recent changes in DOE requirements, all DOE operations are now required to use the CEDE methodology, instead of the annual effective dose equivalent (AEDE) methodology, to evaluate internal radiation exposures. Under the transition from AEDE to CEDE, with a 1.0 {mu}m AMAD particle size, lower bioassay action levels would be required for the UMTRA Project. This translates into an expanded internal dosimetry program where significantly more bioassay monitoring would be required at the UMTRA Project sites. However, for situations where the particle size distribution is known to differ significantly from 1.0 {mu}m AMAD, the DOE allows for corrections to be made to both the estimated dose to workers and the derived air concentration (DAC) values. For particle sizes larger than 1.0 {mu}m AMAD, the calculated CEDE from inhaling tailings would be relatively lower.

Newton, G.J.; Reif, R.H. [CWM Federal Environmental Services, Inc., Albuquerque, NM (United States); Hoover, M.D.

1994-11-01T23:59:59.000Z

94

A Power Control System for a Paper Mill  

E-Print Network [OSTI]

This paper describes the Power Demand Control System installed at the Lufkin Mill of Southland Division, St. Regis Paper Company. The system is based around a microprocessor unit that automatically changes the output of the generators to maintain a...

Richter, G. H.; Keenon, D.

1979-01-01T23:59:59.000Z

95

alstom bowl mill: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

21 22 23 24 25 Next Page Last Page Topic Index 141 Clean Air Act Requirements: Uranium Mill Tailings Environmental Sciences and Ecology Websites Summary: :www.epa.govradiation...

96

aspen pulp mill: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

21 22 23 24 25 Next Page Last Page Topic Index 161 Clean Air Act Requirements: Uranium Mill Tailings Environmental Sciences and Ecology Websites Summary: :www.epa.govradiation...

97

Parametric Study of End Milling Glass Fibre Reinforced Composites  

SciTech Connect (OSTI)

This paper discusses the application of Taguchi 'Design of Experiment' method to investigate the effects of end milling parameters on machinability characteristics of unidirectional E-glass fibre reinforced polymer (GFRP) composites. A series of milling experiments were conducted using tungsten carbide end milling cutters at various spindle speeds, feed rates and depths of cut. Taguchi analysis was carried out and the signal to noise (S/N) ratio with analysis of variance (ANOVA) was employed to analyse the effects of those parameters on GFRP machinability. Overall, the results of the current investigations present some desirable combinations of the machining parameters that can further enhance the end milling machinability characteristics to suit the final requirements of the finished GFRP products.

Azmi, Azwan I.; Lin, Richard J. T.; Bhattacharyya, Debes [Centre for Advanced Composite Materials (CACM), Department of Mechanical Engineering, University of Auckland, Private Bag 92019, Auckland Mail Centre 1142, Auckland (New Zealand)

2011-01-17T23:59:59.000Z

98

Yang-Mills coupling and cosmological duality of extended objects  

E-Print Network [OSTI]

YANG ? MILLS COUPLING AND COSMOLOGICAL DUALITY OF EXTENDED OB JECTS A Thesis by JAN CHRISTOPH PLEFKA Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER... OF SCIENCE December 1992 Major Subject: Physics YANG ? MILLS COUPLING AND COSMOLOGICAL DUALITY OF EXTENDED OBJECTS A Thesis by JAN CHRISTOPH PLEFKA Approved as to style and content by: Micha, el J. D (Chair of Committee) tephen A. Fulling (Member...

Plefka, Jan Christoph

1992-01-01T23:59:59.000Z

99

The rhetoric of economic inquiry in Smith, Whately, and Mill  

E-Print Network [OSTI]

THE RHETORIC OF ECONOMIC INQUIRY IN SMITH, WHATELY, AND MILL A Dissertation by DAVID CHARLES GORE Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of DOCTOR OF PHILOSOPHY May 2005 Major Subject: Speech Communication THE RHETORIC OF ECONOMIC INQUIRY IN SMITH, WHATELY, AND MILL A Dissertation by DAVID CHARLES GORE Submitted to Texas...

Gore, David Charles

2005-08-29T23:59:59.000Z

100

Dust size distribution and concentrations with cottonseed oil mills  

E-Print Network [OSTI]

DUST SIZE DISTRIBUTION AND CONCENTRATIONS WITHIN COTTONSEED OIL MILLS A Thesis by LEE ROY WIEDERHOLD, JR. / I Submitted to the Graduate College of Texas ARM University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE August 1976 Major Subject: Aqricultural Engineering DUST SIZE DISTRIBUTION AND CONCENTRATIONS WITHIN COTTONSEED OIL MILLS A Thesis by LEE ROY WIEDERHOLD, JR. Approved as to style and content by: Chairman of Committee ~Hd fdp t Member ber...

Wiederhold, Lee Roy

1976-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

[working paper] Regional Economic Capacity, Economic Shocks,  

E-Print Network [OSTI]

1 [working paper] Regional Economic Capacity, Economic Shocks, and Economic that makes them more likely to resist economic shocks or to recover quickly from of resilience capacity developed by Foster (2012) is related to economic resilience

Sekhon, Jasjeet S.

102

Fair capacity sharing of multiple aperiodic servers  

E-Print Network [OSTI]

For handling multiple aperiodic tasks with different temporal requirements, multiple aperiodic servers are used. Since capacity is partitioned statically among the multiple servers, they suffer from heavy capacity exhaustions. Bernat and Burns...

Melapudi, Vinod Reddy

2002-01-01T23:59:59.000Z

103

Replacing chemicals in recycle mills with mechanical alternatives  

SciTech Connect (OSTI)

A high-intensity spark fired underwater decomposes a small amount of the water into hydroxyl radicals, which are strong oxidants. These are able to oxidize contaminants such as glue and wood pitch that enter paper recycling mills as a part of the incoming furnish and cost the industry several hundred million dollars. The sparking technique is safe, inexpensive, and is capable of treating large volumes of water, which makes it attractive for mill applications. Several mill trials were run. Sparking caused a decrease in the tack of the deposits in one case. Lower bleach use occurred in two other mills; sparking reduced the degree of ink reattachment to fiber. The payback for either application is attractive. Sparking induced deposition of contaminants in another mill, which is a positive development--if it can be controlled. The technique is also able to degas water and to oxidize odor-causing sulfur compounds. Although one unit has been purchased by a mill, second-order effects caused by the technology needs to be defined further before the technology can be broadly applied.

Institute of Paper Science Technology

2002-07-01T23:59:59.000Z

104

Short wavelength laser  

DOE Patents [OSTI]

A short wavelength laser (28) is provided that is driven by conventional-laser pulses (30, 31). A multiplicity of panels (32), mounted on substrates (34), are supported in two separated and alternately staggered facing and parallel arrays disposed along an approximately linear path (42). When the panels (32) are illuminated by the conventional-laser pulses (30, 31), single pass EUV or soft x-ray laser pulses (44, 46) are produced.

Hagelstein, Peter L. (Livermore, CA)

1986-01-01T23:59:59.000Z

105

> REPLACE THIS LINE WITH YOUR PAPER IDENTIFICATION NUMBER (DOUBLE-CLICK HERE TO EDIT) < 1 An Analytical Framework for Short-Term Resource  

E-Print Network [OSTI]

markets, strategic behavior, capacity gaming. I. INTRODUCTION HE electric system is said to be reliable markets, is capacity. Since sellers need not offer all their capacity to serve the demand, they may engage An Analytical Framework for Short-Term Resource Adequacy in Competitive Electricity Markets Pablo A. Ruiz

106

Can Science and Technology Capacity be Measured?  

E-Print Network [OSTI]

The ability of a nation to participate in the global knowledge economy depends to some extent on its capacities in science and technology. In an effort to assess the capacity of different countries in science and technology, this article updates a classification scheme developed by RAND to measure science and technology capacity for 150 countries of the world.

Wagner, Caroline S; Dutta, Arindum

2015-01-01T23:59:59.000Z

107

Internal Markets for Supply Chain Capacity Allocation  

E-Print Network [OSTI]

Internal Markets for Supply Chain Capacity Allocation David McAdams and Thomas W. Malone Sloan David McAdams & Thomas Malone #12;Internal Markets for Supply Chain Capacity Allocation David Mc ("internal markets") to help allocate manufacturing capacity and determine the prices, delivery dates

108

Iran outlines oil productive capacity  

SciTech Connect (OSTI)

National Iranian Oil Co. (NIOC) tested production limits last month to prove a claim of 4 million bd capacity made at September's meeting of the organization of Petroleum Exporting Countries. Onshore fields account for 3.6 million bd of the total, with offshore fields providing the rest. NIOC plans to expand total capacity to 4.5 million bd by April 1993, consisting of 4 million b/d onshore and 500,000 b/d offshore. Middle East Economic Survey says questions remain about completion dates for gas injection, drilling, and offshore projects, but expansion targets are attainable within the scheduled time. NIOC said some slippage may be unavoidable, but it is confident the objective will be reached by third quarter 1993 at the latest. More than 60 rigs are working or about to be taken under contract to boost development drilling in onshore fields and provide gas injection in some. NIOC has spent $3.2 billion in foreign exchange on the drilling program in the last 2 1/2 years.

Not Available

1992-11-09T23:59:59.000Z

109

Measurements of uranium mill tailings consolidation characteristics  

SciTech Connect (OSTI)

A series of experiments were conducted on uranium mill tailings from the tailings pile in Grand Junction, Colorado, to determine their consolidation characteristics. Three materials (sand, sand/slimes mix, slimes) were loaded under saturated conditions to determine their saturated consolidated behavior. During a separate experiment, samples of the slimes material were kept under a constant load while the pore pressure was increased to determine the partially saturated consolidation behavior. Results of the saturated tests compared well with published data. Sand consolidated the least, while slimes consolidated the most. As each material consolidated, the measured hydraulic conductivity decreased in a linear fashion with respect to the void ratio. Partially saturated experiments with the slimes indicated that there was little consolidation as the pore pressure was increased progressively above 7 kPa. The small amount of consolidation that did occur was only a fraction of the amount of saturated consolidation. Preliminary measurements between pore pressures of 0 and 7 kPa indicated that measurable consolidation could occur in this range of pore pressure, but only if there was no load. 13 references, 13 figures.

Fayer, M J

1985-02-01T23:59:59.000Z

110

Environmental assessment of remedial action at the Shiprock uranium mill tailings site, Shiprock, New Mexico: Volume 1, Text  

SciTech Connect (OSTI)

This document assesses and compares the environmental impacts of various alternatives for remedial action at the shiprock uranium mill tailings site located on the Navajo Indian Reservation, one mile south of Shiprock, New Mexico. The site contains 72 acres of tailings and four of the original mill buildings. The Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA), Public Law 95-604, authorizes the US Department of Energy to clean up the site to reduce the potential health impacts associated with the residual radioactive materials remaining at the site and at associated properties off the site. The US Environmental Protection Agency promulgated standards for the remedial actions (40 CFR 192). Remedial actions must be performed in accordance with these standards and with the concurrence of the Nuclear Regulatory Commission. The proposed action is to stabilize the tailings at their present location by consolidating the tailings and associated contaminated soils into a recontoured pile. A seven-foot-thick radon barrier would be constructed over the pile and various erosion control measures would be taken to assure the long-term integrity of the pile. Three other alternatives which involve moving the tailings to new locations are assessed in this document. These alternatives which involve moving the tailings to new locations are assessed in this document. These alternatives generally involve greater short-term impacts and are more costly but would result in the tailings being stabilized in a more remote location. The no action alternative is also assessed. 99 refs., 40 figs., 58 tabs.

Not Available

1984-05-01T23:59:59.000Z

111

Environmental Assessment of remedial action at the Ambrosia Lake uranium mill tailings site, Ambrosia Lake, New Mexico  

SciTech Connect (OSTI)

This document assesses and compares the environmental impacts of various alternatives for remedial action at the Ambrosia Lake uranium mill tailings site located near Ambrosia Lake, New Mexico. The designated site covers 196 acres and contains 111 acres of tailings and some of the original mill structures. The Uranium Mill Tailings Radiation Control Act (UMTRCA), Public Law 95-604, authorizes the US Department of Energy to clean up the site to reduce the potential health impacts associated with the residual radioactive materials remaining at the site and at associated properties off the site. The US Environmental Protection Agency promulgated standards for th remedial action (40 CFR Part 192). Remedial action must be performed in accordance with these standards and with the concurrence of the Nuclear Regulatory Commission. The proposed action is to stabilize the tailings at their present location by consolidating the tailings and associated contaminated materials into a recontoured pile. A radon barrier would be constructed over the pile and various erosion protection measures would be taken to assure the long-term stability of the pile. Another alternative which would involve moving the tailings to a new location is also assessed in this document. This alternative would generally involve greater short-term impacts and costs but would result in stabilization of the tailings at an undeveloped location. The no action alternative is also assessed in this document.

Not Available

1987-06-01T23:59:59.000Z

112

Capacity Value of Concentrating Solar Power Plants  

SciTech Connect (OSTI)

This study estimates the capacity value of a concentrating solar power (CSP) plant at a variety of locations within the western United States. This is done by optimizing the operation of the CSP plant and by using the effective load carrying capability (ELCC) metric, which is a standard reliability-based capacity value estimation technique. Although the ELCC metric is the most accurate estimation technique, we show that a simpler capacity-factor-based approximation method can closely estimate the ELCC value. Without storage, the capacity value of CSP plants varies widely depending on the year and solar multiple. The average capacity value of plants evaluated ranged from 45%?90% with a solar multiple range of 1.0-1.5. When introducing thermal energy storage (TES), the capacity value of the CSP plant is more difficult to estimate since one must account for energy in storage. We apply a capacity-factor-based technique under two different market settings: an energy-only market and an energy and capacity market. Our results show that adding TES to a CSP plant can increase its capacity value significantly at all of the locations. Adding a single hour of TES significantly increases the capacity value above the no-TES case, and with four hours of storage or more, the average capacity value at all locations exceeds 90%.

Madaeni, S. H.; Sioshansi, R.; Denholm, P.

2011-06-01T23:59:59.000Z

113

Capacity fade of Sony 18650 cells cycled at elevated temperatures Part II. Capacity fade analysis  

E-Print Network [OSTI]

Capacity fade of Sony 18650 cells cycled at elevated temperatures Part II. Capacity fade analysis P August 2002 Abstract A complete capacity fade analysis was carried out for Sony 18650 cells cycled the other losses. # 2002 Elsevier Science B.V. All rights reserved. Keywords: Capacity fade; Sony 18650

Popov, Branko N.

114

NUCLEAR ISOTOPIC DILUTION OF HIGHLY ENRICHED URANIUM BY DRY BLENDING VIA THE RM-2 MILL TECHNOLOGY  

SciTech Connect (OSTI)

DOE has initiated numerous activities to focus on identifying material management strategies to disposition various excess fissile materials. In particular the INEEL has stored 1,700 Kg of offspec HEU at INTEC in CPP-651 vault facility. Currently, the proposed strategies for dispositioning are (a) aqueous dissolution and down blending to LEU via facilities at SRS followed by shipment of the liquid LEU to NFS for fabrication into LWR fuel for the TVA reactors and (b) dilution of the HEU to 0.9% for discard as a waste stream that would no longer have a criticality or proliferation risk without being processed through some type of enrichment system. Dispositioning this inventory as a waste stream via aqueous processing at SRS has been determined to be too costly. Thus, dry blending is the only proposed disposal process for the uranium oxide materials in the CPP-651 vault. Isotopic dilution of HEU to typically less than 20% by dry blending is the key to solving the dispositioning issue (i.e., proliferation) posed by HEU stored at INEEL. RM-2 mill is a technology developed and successfully tested for producing ultra-fine particles by dry grinding. Grinding action in RM-2 mill produces a two million-fold increase in the number of particles being blended in a centrifugal field. In a previous study, the concept of achieving complete and adequate blending and mixing (i.e., no methods were identified to easily separate and concentrate one titanium compound from the other) in remarkably short processing times was successfully tested with surrogate materials (titanium dioxide and titanium mono-oxide) with different particle sizes, hardness and densities. In the current project, the RM-2 milling technology was thoroughly tested with mixtures of natural uranium oxide (NU) and depleted uranium oxide (DU) stock to prove its performance. The effects of mill operating and design variables on the blending of NU/DU oxides were evaluated. First, NU and DU both made of the same oxide, UO{sub 3}, was used in the testing. Next, NU made up of UO{sub 3} and DU made up of UO{sub 2} was used in the test work. In every test, the blend achieved was characterized by spatial sampling of the ground product and analyzing for {sup 235}U concentration. The test work proved that these uranium oxide materials can be blended successfully. The spatial concentration was found to be uniform. Next, sintered thorium oxide pellets were used as surrogate for light water breeder reactor pellets (LWBR). To simulate LWBR pellet dispositioning, the thorium oxide pellets were first ground to a powder form and then the powder was blended with NU. In these tests also the concentration of {sup 235}U and {sup 232}Th in blended products fell within established limits proving the success of RM-2 milling technology. RM-2 milling technology is applicable to any dry radioactive waste, especially brittle solids that can be ground up and mixed with the non-radioactive stock.

Raj K. Rajamani; Sanjeeva Latchireddi; Vikas Devrani; Harappan Sethi; Roger Henry; Nate Chipman

2003-08-01T23:59:59.000Z

115

Uranium Mill Tailings Remedial Action 1993 Roadmap  

SciTech Connect (OSTI)

The 1993 Roadmap for the Uranium Mill Tailings Remedial Action (UMTRA) Project office is a tool to assess and resolve issues. The US Department of Energy (DOE) UMTRA Project Office uses the nine-step roadmapping process as a basis for Surface and Groundwater Project planning. This is the second year the Roadmap document has been used to identify key issues and assumptions, develop logic diagrams, and outline milestones. This document is a key element of the DOE planning process. A multi-interest group used the nine-step process to focus on issues, root cause analysis and resolutions. This core group updated and incorporated comments on the basic assumptions, then used these assumptions to identify issues. The list of assumptions was categorized into the following areas: institutional, regulatory compliance, project management, human resource requirements, and other site-specific assumptions. The group identified 10 issues in the analysis phase. All of the issues are ranked according to importance. The number one issue from the 1992 Roadmap, ``Lack of sufficient human resources,`` remained the number one issue in 1993. The issues and their ranking are as follows: Lack of sufficient human resources; increasing regulatory requirements; unresolved groundwater issues; extension of UMTRCA through September 30, 1998; lack of post-UMTRA and post-cell closure policies; unpredictable amounts and timing of Federal funding; lack of regulatory compliance agreements; problem with states providing their share of remedial action costs; different interests and priorities among participants; and technology development/transfer. The issues are outlined and analyzed in detail in Section 8.0, with a schedule for resolution of these issues in Section 9.0.

Not Available

1993-10-18T23:59:59.000Z

116

Mechanical alloying of Si and Ge in a planetary ball mill: Milling parameters and microscopic evolution of alloy formation  

SciTech Connect (OSTI)

The external parameters geometry and frequency of a planetary ball mill were adjusted in order to minimize the duration of mechanically induced Si-Ge alloy formation. Experimental results were compared with theoretical calculations on impact energies and milling power. It was found that a planetary ball mill with a ratio of the planetary to the system wheel`s frequency of {minus}3 delivers the best milling performance for vial sizes between 0.2 and 0.33 that of the system wheel size. Microstructural investigations on powder compacts revealed that a solid state diffusion mechanism of Ge into the harder Si seems to be the responsible process for realizing a homogeneous Si-Ge alloy. Crystallite sizes of the processed powders were 30 nm. The knowledge of the influence of external milling parameters on the comminution and alloying behavior of substances and the resulting internal structure of the processed ingots may help in a future correlation between thermoelectrical properties and microstructure. {copyright} {ital 1995} {ital American} {ital Institute} {ital of} {ital Physics}.

Schilz, J.; Pixius, K.; Amend, W. [Institute of Materials Research, German Aerospace Research Establishment (DLR), Linder Hoehe, 51147 Koehn (Germany); Plate, M.; Meyer, H. [Retsch Co., Rheinische Str. 36, 42781 Haan (Germany)

1994-08-10T23:59:59.000Z

117

Stabilization and restoration of an uranium mill site in Spain  

SciTech Connect (OSTI)

In the south of Spain on the outskirts of the town of Andujar an inactive uranium mill tailings site has been remediated in place. Mill equipment, buildings and process facilities have been dismantled and demolished and 06q the resulting metal wastes and debris have been placed in the tailings pile. The tailings mass has been reshaped by flattening the sideslopes to improve stability and a cover system has been placed over the pile. Remedial action works started in February 1991 and were completed by April 1994. This paper describes the remediation works for the closure of the Andujar mill site and in particular discusses the approaches used for the dismantling and demolition of the processing facilities and the stabilization of the tailings pile.

Santiago, J.L.; Estevez, C.P. [ENRESA, Madrid (Spain)

1995-12-31T23:59:59.000Z

118

Design of Refractory Linings for Balanced Energy Efficiency, Uptime, and Capacity in Lime Kilns  

SciTech Connect (OSTI)

The rotary kilns used by the pulp and paper industry to regenerate lime in the Kraft process are very energy intensive. Throughout the 90 s, in response to increasing fuel prices, the industry used back up insulation in conjunction with the high alumina brick used to line the burning zones of their kilns. While this improved energy efficiency, the practice of installing insulating brick behind the working lining increased the inner wall temperatures. In the worst case, due to the increased temperatures, rapid brick failures occurred causing unscheduled outages and expensive repairs. Despite these issues, for the most part, the industry continued to use insulating refractory linings in that the energy savings were large enough to offset any increase in the cost of maintaining the refractory lining. Due to the dramatic decline in the price of natural gas in some areas combined with mounting pressures to increasing production of existing assets, over the last decade, many mills are focusing more on increasing the uptime of their kilns as opposed to energy savings. To this end, a growing number of mills are using basic (magnesia based) brick instead of high alumina brick to line the burning zone of the kiln since the lime mud does not react with these bricks at the operating temperatures of the burning zone of the kiln. In the extreme case, a few mills have chosen to install basic brick in the front end of the kiln running a length equivalent to 10 diameters. While the use of basic brick can increase the uptime of the kiln and reduce the cost to maintain the refractory lining, it does dramatically increase the heat losses resulting from the increased operating temperatures of the shell. Also, over long periods of time operating at these high temperatures, damage can occur in the shell. There are tradeoffs between energy efficiency, capacity and uptime. When fuel prices are very high, it makes sense to insulate the lining. When fuel prices are lower, trading some thermal efficiency for increased uptime and capacity seems reasonable. This paper considers a number of refractory linings in an effort to develop optimized operating strategies that balance these factors. In addition to considering a range of refractory materials, the paper examines other factors such as the chain area, discharge dams and other operating variables that impact the service life of the refractory lining. The paper provides recommendations that will help mill personnel develop a strategy to select a refractory lining that is optimized for their specific situation.

Gorog, John Peter [ORNL; Hemrick, James Gordon [ORNL; Walker, Harold [Refratechnik North America, Inc.; Leary, William R [ORNL; Ellis, Murray [Australian Paper, Co.

2014-01-01T23:59:59.000Z

119

Generation capacity expansion in restructured energy markets.  

E-Print Network [OSTI]

??With a significant number of states in the U.S. and countries around the world trading electricity in restructured markets, a sizeable proportion of capacity expansion… (more)

Nanduri, Vishnuteja

2009-01-01T23:59:59.000Z

120

Increasing water holding capacity for irrigation  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Increasing water holding capacity for irrigation Reseachers recommend solutions for sediment trapping in irrigation system LANL and SNL leveraged technical expertise to determine...

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Quantum Capacities of Channels with small Environment  

E-Print Network [OSTI]

We investigate the quantum capacity of noisy quantum channels which can be represented by coupling a system to an effectively small environment. A capacity formula is derived for all cases where both system and environment are two-dimensional--including all extremal qubit channels. Similarly, for channels acting on higher dimensional systems we show that the capacity can be determined if the channel arises from a sufficiently small coupling to a qubit environment. Extensions to instances of channels with larger environment are provided and it is shown that bounds on the capacity with unconstrained environment can be obtained from decompositions into channels with small environment.

Michael M. Wolf; David Perez-Garcia

2006-07-11T23:59:59.000Z

122

Worldwide Energy Efficiency Action through Capacity Building...  

Open Energy Info (EERE)

and Training (WEACT) Jump to: navigation, search Logo: Worldwide Energy Efficiency Action through Capacity Building and Training (WEACT) Name Worldwide Energy Efficiency Action...

123

Solar Energy and Capacity Value (Fact Sheet)  

SciTech Connect (OSTI)

This is a one-page, two-sided fact sheet on the capacity of solar power to provide value to utilities and power system operators.

Not Available

2013-09-01T23:59:59.000Z

124

Baseline risk assessment of ground water contamination at the Uranium Mill Tailings Site in Lakeview, Oregon  

SciTech Connect (OSTI)

This Baseline Risk Assessment of Ground Water Contamination at the Uranium Mill Tailings Site in Lake view, Oregon evaluates potential impacts to public health or the environment resulting from ground water contamination at the former uranium mill processing site.

Not Available

1994-10-01T23:59:59.000Z

125

Solution of symmetry equation and hierarchy of self dual Yang-Mills systems  

E-Print Network [OSTI]

The solution of symmetry equation of Yang-Mills self dual system is found in explicit form of its raising Hamiltonian operator. Thus explicit form of equations of self dual Yang Mills hierarchy is constructed.

A. N. Leznov

2008-02-11T23:59:59.000Z

126

Advanced Powerhouse Controls Save Pulp Mill $500 in Purchased Energy in First Month  

E-Print Network [OSTI]

This case study describes the application of advanced regulatory and supervisory controls to powerhouse operations at a large pulp mill in central British Columbia. Substantial reductions in mill operating costs were achieved by actively managing...

Morrison, R.; Hilder, S.

2004-01-01T23:59:59.000Z

127

A model of light interception and carbon balance for a sweet chestnut coppice (Castanea sativa Mill.)  

E-Print Network [OSTI]

A model of light interception and carbon balance for a sweet chestnut coppice (Castanea sativa Mill photosynthesis, wood respiration and aerial growth in a sweet chestnut (Castanea sativa Mill.) coppice

Paris-Sud XI, Université de

128

Uranium Mill Tailings Radiation Control Act of 1978  

SciTech Connect (OSTI)

The long-term environmental effects of the Uranium Mill Tailings Radiation Control Act of 1978 address the public health hazards of radioactive wastes and recognize the significance of this issue to public acceptance of nuclear energy. Title I of the Act deals with stabilizing and controlling mill tailings at inactive sites and classifies the sites by priority. It represents a major Federal commitment. Title II changes and strengthens Nuclear Regulatory Commission authority, but it will have little overall impact. It is not possible to assess the Act's effect because there is no way to know if current technology will be adequate for the length of time required. 76 references. (DCK)

Magee, J.

1980-01-01T23:59:59.000Z

129

Advanced Modeling and Materials in Kraft Pulp Mills  

SciTech Connect (OSTI)

This CRADA provided technical support to the Weyerhaeuser Company on a number of issues related to the performance and/or selection of materials at a number of locations in a pulp and paper mill. The studies related primarily to components for black liquor recovery boilers, but some effort was directed toward black liquor gasifiers and rolls for paper machines. The purpose of this CRADA was to assist Weyerhaeuser in the evaluation of materials exposed in various paper mill environments and to provide direction in the selection of alternate materials, when appropriate.

Keiser, J.R.; Gorog, J.P.

2002-05-15T23:59:59.000Z

130

Equivariance on Discrete Space and Yang-Mills-Higgs Model  

E-Print Network [OSTI]

We introduce the basic equivariant quantity $Q$ in the gauge theory on the noncommutative descrete $Z_{2}$ space, which plays an important role for the equivariant dimensional reduction. If the gauge configuration of the ground state on the extra dimensional space is described by the equivariant $Q$, then the extra dimensional space is invisible. Especially, using the equivariance principle, we show that the Yang-Mills theory on $R^{2}\\times Z_{2}$ space is equivalent to the Yang-Mills-Higgs model on $R^{2}$ space. It can be said that this model is the simplest model of this type.

Ikemori, Hitoshi; Matsui, Yoshimitsu; Otsu, Hideharu; Sato, Toshiro

2015-01-01T23:59:59.000Z

131

Equivariance on Discrete Space and Yang-Mills-Higgs Model  

E-Print Network [OSTI]

We introduce the basic equivariant quantity $Q$ in the gauge theory on the noncommutative descrete $Z_{2}$ space, which plays an important role for the equivariant dimensional reduction. If the gauge configuration of the ground state on the extra dimensional space is described by the equivariant $Q$, then the extra dimensional space is invisible. Especially, using the equivariance principle, we show that the Yang-Mills theory on $R^{2}\\times Z_{2}$ space is equivalent to the Yang-Mills-Higgs model on $R^{2}$ space. It can be said that this model is the simplest model of this type.

Hitoshi Ikemori; Shinsaku Kitakado; Yoshimitsu Matsui; Hideharu Otsu; Toshiro Sato

2015-04-07T23:59:59.000Z

132

Fermentation and chemical treatment of pulp and paper mill sludge  

DOE Patents [OSTI]

A method of chemically treating partially de-ashed pulp and/or paper mill sludge to obtain products of value comprising taking a sample of primary sludge from a Kraft paper mill process, partially de-ashing the primary sludge by physical means, and further treating the primary sludge to obtain the products of value, including further treating the resulting sludge and using the resulting sludge as a substrate to produce cellulase in an efficient manner using the resulting sludge as the only carbon source and mixtures of inorganic salts as the primary nitrogen source, and including further treating the resulting sludge and using the resulting sludge to produce ethanol.

Lee, Yoon Y; Wang, Wei; Kang, Li

2014-12-02T23:59:59.000Z

133

Reclamation and groundwater restoration in the uranium milling industry: An assessment of UMTRCA, title II  

SciTech Connect (OSTI)

In 1978, Congress passed the Uranium Mill Tailings Radiation Control Act (UMTRCA) to regulate the disposal and reclamation of uranium mill tailings.This article examines the implementation of this legislation through eight cases of uranium mills in New Mexico, Wyoming, and Utah now being reclaimed. The eight cases examined here make up an important part of the total reclamation picture in the uranium milling industry.

Collins, J.D.

1996-12-31T23:59:59.000Z

134

Earthquake hazards in the Intermountain U.S.: Issues relevant to uranium mill tailings disposal  

E-Print Network [OSTI]

. Consequently, the seismic safety of U.S. uranium mill tailings sites, which are located almost exclusively in

Ivan G. Wong; Susan S. Olig; Bruce W. Hassinger; Richard E. Blubaugh

135

Life in Challenge Mills, Yuba County, California, 18751915 Andrew Martin Leach  

E-Print Network [OSTI]

Mills, Yuba County, California, 1875­1915 steam engine and boiler, production increased to 40,000 board

Standiford, Richard B.

136

The effect of temperature and time on the mechanical properties of lightly milled rice  

E-Print Network [OSTI]

MATERIALS AND EQUIPMENT Test Apparatus Dynamic Relative Humidity System PROCEDURE Milling and Equilibrating the R1ce Grain Compression Experiments Tension Experiments 10 10 12 14 15 16 Determination of Strength during Noisture Adsorption... TENSION LOADING OF BLUEBELLE LIGHTLY MILLED RICE 2 RESULTS FROM COMPRESSION LOADING OF BLUEBELLE LIGHTLY MILLED RICE 3 RESULTS FROM LOADING OF BLUEBELLE LIGHTLY MILLED RICE IN DIFFERENT POSITIONS 27 28 47 LIST OF FIGURES Figure Page Arrangement...

Maa, Tsorng-Jong

1974-01-01T23:59:59.000Z

137

Managing nuclear predominant generating capacity  

SciTech Connect (OSTI)

The most common belief, associated with nuclear power plant, leads to the conclusion that it can only operate, as a base load plant. This observation can be reversed, by just looking at large generating capacity, using an important nuclear generation mix. Nuclear plants may certainly load follow and contribute to the grid frequency control. The French example illustrates these possibilities. The reactor control of French units has been customized to accommodate the grid requests. Managing such a large nuclear plant fleet requires various actions be taken, ranging from a daily to a multi-annual perspective. The paper describes the various contributions leading to safe, reliable, well accepted and cost competitive nuclear plants in France. The combination of all aspects related to operations, maintenance scheduling, nuclear safety management, are presented. The use of PWR units carries considerable weight in economic terms, with several hundred million francs tied in with outage scheduling every year. This necessitates a global view of the entire generating system which can be mobilized to meet demand. There is considerable interaction between units as, on the one hand, they are competing to satisfy the same need, and, on the other hand, reducing maintenance costs means sharing the necessary resources, and thus a coordinated staggering of outages. In addition, nuclear fuel is an energy reserve which remains in the reactor for 3 or 4 years, with some of the fuel renewed each year. Due to the memory effect, the fuel retains a memory of past use, so that today's choices impact upon the future. A medium-term view of fuel management is also necessary.

Bouget, Y.H.; Herbin, H.C.; Carbonnier, D.

1998-07-01T23:59:59.000Z

138

North Dakota Refining Capacity Study  

SciTech Connect (OSTI)

According to a 2008 report issued by the United States Geological Survey, North Dakota and Montana have an estimated 3.0 to 4.3 billion barrels of undiscovered, technically recoverable oil in an area known as the Bakken Formation. With the size and remoteness of the discovery, the question became 'can a business case be made for increasing refining capacity in North Dakota?' And, if so what is the impact to existing players in the region. To answer the question, a study committee comprised of leaders in the region's petroleum industry were brought together to define the scope of the study, hire a consulting firm and oversee the study. The study committee met frequently to provide input on the findings and modify the course of the study, as needed. The study concluded that the Petroleum Area Defense District II (PADD II) has an oversupply of gasoline. With that in mind, a niche market, naphtha, was identified. Naphtha is used as a diluent used for pipelining the bitumen (heavy crude) from Canada to crude markets. The study predicted there will continue to be an increase in the demand for naphtha through 2030. The study estimated the optimal configuration for the refinery at 34,000 barrels per day (BPD) producing 15,000 BPD of naphtha and a 52 percent refinery charge for jet and diesel yield. The financial modeling assumed the sponsor of a refinery would invest its own capital to pay for construction costs. With this assumption, the internal rate of return is 9.2 percent which is not sufficient to attract traditional investment given the risk factor of the project. With that in mind, those interested in pursuing this niche market will need to identify incentives to improve the rate of return.

Dennis Hill; Kurt Swenson; Carl Tuura; Jim Simon; Robert Vermette; Gilberto Marcha; Steve Kelly; David Wells; Ed Palmer; Kuo Yu; Tram Nguyen; Juliam Migliavacca

2011-01-05T23:59:59.000Z

139

Short-term Wind Power Prediction for Offshore Wind Farms -Evaluation of Fuzzy-Neural Network Based Models  

E-Print Network [OSTI]

Short-term Wind Power Prediction for Offshore Wind Farms - Evaluation of Fuzzy-Neural Network Based of wind power capacities are likely to take place offshore. As for onshore wind parks, short-term wind of offshore farms and their secure integration to the grid. Modeling the behavior of large wind farms

Paris-Sud XI, Université de

140

Electrodeless short pulse laser  

SciTech Connect (OSTI)

A system is described for the generation of coherent beams of radiation, which consists of: a tube defining a resonant cavity containing a discharge plasma capable of producing coherent radiation, the tube having an elongated shape along an optical axis along the longitudinal axis of the tube, the tube having end portions and an elongated constricted portion connecting the end portions, and the tube having laser windows sealing the end portions to form a closed envelope containing the discharge plasma, a mirror on the optical axis near at least one end of the tube, first and second external electrode means on the outside surfaces of the tube adjacent the opposite ends of the tube, the external electrode means being capacitively coupled to the discharge plasma, and means for providing a source of short pulses electrically to the first external electrode means and means for coupling the second external electrode means to a point of reference potential, further characterized by first and second internal electrode means respectively adjacent the first and second external electrode means and capacitively coupled thereto, the tube having end portions sealed to form a closed envelope containing the discharge plasma and the internal electrode means.

Proud, J.M.; Baird, D.H.; Kramer, J.M.; Lester, J.E.

1986-06-03T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Low Temperature Milling of the LiNH2 + LiH Hydrogen Storage System...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Milling of the LiNH2 + LiH Hydrogen Storage System. Low Temperature Milling of the LiNH2 + LiH Hydrogen Storage System. Abstract: Ball milling of the LiNH2 + LiH storage system was...

142

Reconnaissance Soil Geochemistry at the Riverton Uranium Mill Tailings Remedial Action Site, Fremont  

E-Print Network [OSTI]

Reconnaissance Soil Geochemistry at the Riverton Uranium Mill Tailings Remedial Action Site, Reconnaissance soil geochemistry at the Riverton Uranium Mill Tailings Remedial Action Site, Fremont County.....................................................................................................................................................link Figures Figure 1. Location of 19 soil samples collected from the Riverton Uranium Mill Tailings Remedial

Fleskes, Joe

143

EPA Review of Standards for Uranium and Thorium Milling Facilities @ 40 CFR Parts 61 and 192.  

E-Print Network [OSTI]

EPA Review of Standards for Uranium and Thorium Milling Facilities @ 40 CFR Parts 61 of EPA standards for Uranium and Thorium Milling Facilities @ 40 CFR Parts 61 and 192. I have been scientific perspectives related to the adequacy of existing public exposure standards for uranium mills

144

Solving Steel Mill Slab Problems with Constraint-Based Techniques: CP, LNS, and  

E-Print Network [OSTI]

Solving Steel Mill Slab Problems with Constraint-Based Techniques: CP, LNS, and CBLS Pierre Schaus, 2010 Abstract The Steel Mill Slab Problem is an optimization benchmark that has been studied for a long approaches. In a second part of the paper, we present a variation of the Steel Mill Slab Problem whose aim

Deville, Yves

145

Optimizing the Utility System of a Tissue Paper Mill Using Pinch Technology  

E-Print Network [OSTI]

A tissue paper mill in southern California had existing utility demands of 7.1 MW for the tissue mill (13 MW for the whole site), and 55 MM Btu/hr of fuel gas for the steam boiler. Total utility costs were $12 MM per year. The mill was seriously...

Kumana, J. D.; Sung, R. D.

146

BIOMASS AND BLACK LIQUOR GASIFIER/GAS TURBINE COGENERATION AT PULP AND PAPER MILLS  

E-Print Network [OSTI]

BIOMASS AND BLACK LIQUOR GASIFIER/GAS TURBINE COGENERATION AT PULP AND PAPER MILLS ERIC D. LARSON modeling of gasifier/gas turbine pulp-mill cogeneration systemsusing gasifier designs under commercial gasification. The use of biomass fuels with gas turbines could transform a typical pulp mill from a net

147

Short term generation scheduling in photovoltaic-utility grid with battery storage  

SciTech Connect (OSTI)

This paper presents an efficient approach to short term resource scheduling for an integrated thermal and photovoltaic-battery generation. The proposed model incorporated battery storage for peak load shaving. Several constraints including battery capacity, minimum up/down time and ramp rates for thermal units, as well as natural photovoltaic (PV) capacity are considered in the proposed model. A case study composed of 26 thermal units and a PV-battery plant is presented to test the efficiency of the method.

Marwali, M.K.C.; Ma, H.; Shahidehpour, S.M. [Illinois Inst. of Tech., Chicago, IL (United States). Dept. of Electrical and Computer Engineering] [Illinois Inst. of Tech., Chicago, IL (United States). Dept. of Electrical and Computer Engineering; Abdul-Rahman, K.H. [Siemens Energy and Automation, Brooklyn Park, MN (United States)] [Siemens Energy and Automation, Brooklyn Park, MN (United States)

1998-08-01T23:59:59.000Z

148

REDUCTION CAPACITY OF SALTSTONE AND SALTSTONE COMPONENTS  

SciTech Connect (OSTI)

The duration that saltstone retains its ability to immobilize some key radionuclides, such as technetium (Tc), plutonium (Pu), and neptunium (Np), depends on its capacity to maintain a low redox status (or low oxidation state). The reduction capacity is a measure of the mass of reductants present in the saltstone; the reductants are the active ingredients that immobilize Tc, Pu, and Np. Once reductants are exhausted, the saltstone loses its ability to immobilize these radionuclides. The reduction capacity values reported here are based on the Ce(IV)/Fe(II) system. The Portland cement (198 {micro}eq/g) and especially the fly ash (299 {micro}eq/g) had a measurable amount of reduction capacity, but the blast furnace slag (820 {micro}eq/g) not surprisingly accounted for most of the reduction capacity. The blast furnace slag contains ferrous iron and sulfides which are strong reducing and precipitating species for a large number of solids. Three saltstone samples containing 45% slag or one sample containing 90% slag had essentially the same reduction capacity as pure slag. There appears to be some critical concentration between 10% and 45% slag in the Saltstone formulation that is needed to create the maximum reduction capacity. Values from this work supported those previously reported, namely that the reduction capacity of SRS saltstone is about 820 {micro}eq/g; this value is recommended for estimating the longevity that the Saltstone Disposal Facility will retain its ability to immobilize radionuclides.

Roberts, K.; Kaplan, D.

2009-11-30T23:59:59.000Z

149

Uranium Mill Tailings Remedial Action (UMTRA) Project. [UMTRA project  

SciTech Connect (OSTI)

The mission of the Uranium Mill Tailings Remedial Action (UMTRA) Project is explicitly stated and directed in the Uranium Mill Tailings Radiation Control Act of 1978, hereinafter referred to as the Act.'' Title I of the Act authorizes the Department of Energy (DOE) to undertake remedial action at designated inactive uranium processing sites (Attachment 1 and 2) and associated vicinity properties containing uranium mill tailings and other residual radioactive materials derived from the processing site. The purpose of the remedial actions is to stabilize and control such uranium mill tailings and other residual radioactive materials in a safe and environmentally sound manner to minimize radiation health hazards to the public. The principal health hazards and environmental concerns are: the inhalation of air particulates contaminated as a result of the emanation of radon from the tailings piles and the subsequent decay of radon daughters; and the contamination of surface and groundwaters with radionuclides or other chemically toxic materials. This UMTRA Project Plan identifies the mission and objectives of the project, outlines the technical and managerial approach for achieving them, and summarizes the performance, cost, and schedule baselines which have been established to guide operational activity. Estimated cost increases by 15 percent, or if the schedule slips by six months. 4 refs.

Not Available

1989-09-01T23:59:59.000Z

150

The inheritance of fruit colour in apple (Malus pumila Mill.)  

E-Print Network [OSTI]

The inheritance of fruit colour in apple (Malus pumila Mill.) Allan G. WHITE Yves LESPINASSE that red fruit colour was determined by two dominant complementary genes. Blush and red colour did key words : Skin colour, hybridization. R�SUM� Hérédité de la couleur du fruit chez le pommier (Malus

Paris-Sud XI, Université de

151

INTRODUCTION TO MACHINING 1.2 MILLING MACHINE  

E-Print Network [OSTI]

and rotates inside the quill (which can be moved vertically). Spindle speed selector: typically a wheel which in either the x or y direction into the workpiece (peripheral cutting). -Ball nose end mill: Ball nose end advanced, sculpted surfaces. Figure 1.2.3: Endmills Figure1. 2.4: Ball Nose Endmill 19 #12;INTRODUCTION

Sun, Yu

152

Detection of instabilities and transition in milling operation using wavelets  

E-Print Network [OSTI]

and undesirable due to their detrimental effects. Chatter is one such type of instability and is characterized by the violent relative vibration between the workpiece and tool. The objective of this research is to detect the onset of instabilities in milling...

Khurjekar, Parag Padmakar

2000-01-01T23:59:59.000Z

153

Boise Inc. St. Helens Paper Mill Achieves Significant Fuel Savings  

SciTech Connect (OSTI)

This case study describes how the Boise Inc. paper mill in St. Helens, Oregon, achieved annual savings of approximately 154,000 MMBtu and more than $1 million after receiving a DOE Save Energy Now energy assessment and implementing recommendations to improve the efficiency of its steam system.

Not Available

2008-05-01T23:59:59.000Z

154

Current issues (and problems) in uranium mine and mill site remediation  

SciTech Connect (OSTI)

The environmental impact of the mining and milling of uranium ores is similar to that of traditional metal mining with the added factor of the characteristic radioactivity in uranium ores. Residues of these ores therefore generate specific potential hazards requiring special precautions on a site specific basis, as well as special regulatory procedures and controls to ensure protection of public health and safety in the long term. There are strong indications that on a global scale U-mining tailings management and remediation-activities are steadily becoming governed by the ultimate goal of sustainable stabilization and re-establishment of a healthy environment, rather than by immediate or short term needs. In Central Europe rehabilitation of uranium mining and milling districts has only started. Some problems are listed as follows: (1) Limitation, long term control and prediction of aquatic and atmospheric dispersal of contaminants from tailings impoundments, waste rock dumps and abandoned underground mines, (2) Dewatering of tailings (large volumes), (3) Design of cover systems and inhibition of microbian process, (4) Controlled flooding of extensive underground mine workings and related prognosis and control of containment dispersion, (5) Reduction of Rn-exhalation during the flooding process and after mine abandonment, in particular in areas close to densely populated regions, (6) Determination of long term radiological impacts on residents near sources of contamination and identification of natural background levels, (7) Identification of critical containment pathways that remain active, (8) Conception and implementation of a comprehensive monitoring system for all pathways which would operate on a long term basis, (9) Limitation of mine water drainage to be treated and decontaminated and of resulting sludges (in considerable quantities) to be disposed of and which would have to be classified as hazardous waste in the future due to their radionuclide content.

Quarch, H. [DSR GmbH, Saarbruecken (Germany); Kuhlmann, J.; Zettwoog, P. [CERTAC, Auffargis (France)

1994-12-31T23:59:59.000Z

155

Photovoltaics effective capacity: Interim final report 2  

SciTech Connect (OSTI)

The authors provide solid evidence, based on more than 8 million data points, that regional photovoltaic (PV) effective capacity is largely unrelated to the region`s solar resource. They confirm, however, that effective capacity is strongly related to load-shape characteristics. The load-shape effective-capacity relationship appears to be valid for end-use loads as small as 100 kW, except possibly in the case of electrically heated buildings. This relationship was used as a tool to produce a US map of PV`s effective capacity. The regions of highest effective capacities include (1) the central US from the northern Great Plains to the metropolitan areas of Chicago and Detroit, down to the lower Mississippi Valley, (2) California and western Arizona, and (3) the northeast metropolitan corridor. The features of this map are considerably different from the traditional solar resource maps. They tend to reflect the socio-economic and climatic factors that indirectly drive PV`s effective capacity: e.g., commercial air-conditioning, little use of electric heat, and strong summer heat waves. The map provides a new and significant insight to a comprehensive valuation of the PV resource. The authors assembled preliminary evidence showing that end-use load type may be related to PV`s effective capacity. Highest effective capacities were found for (nonelectrically heated) office buildings, followed by hospitals. Lowest capacities were found for airports and residences. Many more data points are needed, however, to ascertain and characterize these preliminary findings.

Perez, R.; Seals, R. [State Univ. of New York, Albany, NY (United States). Atmospheric Sciences Research Center

1997-11-01T23:59:59.000Z

156

Representation of the Solar Capacity Value in the ReEDS Capacity Expansion Model: Preprint  

SciTech Connect (OSTI)

An important emerging issue is the estimation of renewables' contributions to reliably meeting system demand, or their capacity value. While the capacity value of thermal generation can be estimated easily, assessment of wind and solar requires a more nuanced approach due to resource variability. Reliability-based methods, particularly, effective load-carrying capacity (ELCC), are considered to be the most robust techniques for addressing this resource variability. The Regional Energy Deployment System (ReEDS) capacity expansion model and other long-term electricity capacity planning models require an approach to estimating CV for generalized PV and system configurations with low computational and data requirements. In this paper we validate treatment of solar photovoltaic (PV) capacity value by ReEDS capacity expansion model by comparing model results to literature for a range of energy penetration levels. Results from the ReEDS model are found to compare well with both comparisons--despite not being resolved at an hourly scale.

Sigrin, B.; Sullivan, P.; Ibanez, E.; Margolis, R.

2014-08-01T23:59:59.000Z

157

California: Conducting Polymer Binder Boosts Storage Capacity...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

- 10:17am Addthis Working with Nextval, Inc., Lawrence Berkeley National Laboratory (LBNL) developed a Conducting Polymer Binder for high-capacity lithium-ion batteries. With a...

158

Internal Markets for Supply Chain Capacity Allocation  

E-Print Network [OSTI]

This paper explores the possibility of solving supply chain capacity allocation problems using internal markets among employees of the same company. Unlike earlier forms of transfer pricing, IT now makes it easier for such ...

McAdams, David

2005-07-08T23:59:59.000Z

159

Capacity Building Project with Howard University  

Broader source: Energy.gov [DOE]

The purpose of this initiative is to build community capacity for public participation in environmental and energy decision making. The target communities are those impacted by U.S. Department of...

160

Expandability, reversibility, and optimal capacity choice  

E-Print Network [OSTI]

We develop continuous-time models of capacity choice when demand fluctuates stochastically, and the firm's opportunities to expand or contract are limited. Specifically, we consider costs of investing or disinvesting that ...

Dixit, Avinash K.

1997-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Feedback Capacity of the Compound Channel  

E-Print Network [OSTI]

In this work, we find the capacity of a compound finite-state channel (FSC) with time-invariant deterministic feedback. We consider the use of fixed length block codes over the compound channel. Our achievability result ...

Shrader, Brooke E.

162

Inventories and capacity utilization in general equilibrium  

E-Print Network [OSTI]

The primary goal of this dissertation is to gain a better understanding, in thecontext of a dynamic stochastic general equilibrium framework, of the role of inventories and capacity utilization (of both capital and labor) and, in particular...

Trupkin, Danilo Rogelio

2009-05-15T23:59:59.000Z

163

Measuring the capacity impacts of demand response  

SciTech Connect (OSTI)

Critical peak pricing and peak time rebate programs offer benefits by increasing system reliability, and therefore, reducing capacity needs of the electric power system. These benefits, however, decrease substantially as the size of the programs grows relative to the system size. More flexible schemes for deployment of demand response can help address the decreasing returns to scale in capacity value, but more flexible demand response has decreasing returns to scale as well. (author)

Earle, Robert; Kahn, Edward P.; Macan, Edo

2009-07-15T23:59:59.000Z

164

Wind Resource Assessment Report: Mille Lacs Indian Reservation, Minnesota  

SciTech Connect (OSTI)

The U.S. Environmental Protection Agency (EPA) launched the RE-Powering America's Land initiative to encourage development of renewable energy on potentially contaminated land and mine sites. EPA collaborated with the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL) and the Mille Lacs Band of Chippewa Indians to evaluate the wind resource and examine the feasibility of a wind project at a contaminated site located on the Mille Lacs Indian Reservation in Minnesota. The wind monitoring effort involved the installation of a 60-m met tower and the collection of 18 months of wind data at multiple heights above the ground. This report focuses on the wind resource assessment, the estimated energy production of wind turbines, and an assessment of the economic feasibility of a potential wind project sited this site.

Jimenez, A. C.

2013-12-01T23:59:59.000Z

165

Short courses in Composite Materials  

E-Print Network [OSTI]

Short courses in Composite Materials Overview The ability to tailor the material properties used. Combining the adaptability of composites with clear weight savings, whilst tailoring materials properties Airbus and Glyndr University, the Advanced Composites Training and Development Centre educates current

Davies, John N.

166

Short-Term Energy Outlook  

U.S. Energy Information Administration (EIA) Indexed Site

Chart Gallery for April 2015 Short-Term Energy Outlook U.S. Energy Information Administration Independent Statistics & Analysis 0 20 40 60 80 100 120 140 160 180 200 220 Jan 2014...

167

Short-Term Energy Outlook  

Gasoline and Diesel Fuel Update (EIA)

day Forecast -1.0 2012 2013 2014 OPEC countries North America Russia and Caspian Sea Latin America North Sea Other Non-OPEC Source: Short-Term Energy Outlook, November 2013 -1 0...

168

Remedial action plan and site design for stabilization of the inactive uranium mill tailings site at Tuba City, Arizona. [Uranium Mill Tailings Remedial Action (UMTRA) Project  

SciTech Connect (OSTI)

This appendix assesses the present conditions and data for the inactive uranium mill site near Tuba City, Arizona. It consolidates available engineering, radiological, geotechnical, hydrological, meterological, and other information pertinent to the design of the Remedial Action Plan (RAP). The data characterize conditions at the mill and tailings site so that the Remedial Action Contractor (RAC) may complete final designs of the remedial actions.

Not Available

1987-05-01T23:59:59.000Z

169

Uranium mill tailings remedial action project real estate management plan  

SciTech Connect (OSTI)

This plan summarizes the real estate requirements of the US Department of Energy`s (DOE) Uranium Mill Tailings Action (UMTRA) Project, identifies the roles and responsibilities of project participants involved in real estate activities, and describes the approaches used for completing these requirements. This document is intended to serve as a practical guide for all project participants. It is intended to be consistent with all formal agreements, but if a conflict is identified, the formal agreements will take precedence.

Not Available

1994-09-01T23:59:59.000Z

170

From: Mills, Pamela To: Congestion Study Comments Cc: Strack, Jan  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Electrical Resistivityconnie0:59 PMWednesday, DecemberMills,

171

Mills County, Texas: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 -Energieprojekte GmbH JumpSprings, Vermont:isMillersport,Mills County, Texas: Energy

172

Mills River, North Carolina: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 -Energieprojekte GmbH JumpSprings, Vermont:isMillersport,Mills County, Texas:

173

Gates Mills, Ohio: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to: navigation, search Equivalent6894093° Loading69.County, North Carolina: EnergyMills

174

Magnet Coil Shorted Turn Detector  

SciTech Connect (OSTI)

The Magnet Coil Shorted Turn Detector has been developed to facilitate the location of shorted turns in magnet coils. Finding these shorted turns is necessary to determine failure modes that are a necessary step in developing future production techniques. Up to this point, coils with shorted turns had the insulation burned off without the fault having been located. This disassembly process destroyed any chance of being able to find the fault. In order to maintain a flux balance in a coupled system such as a magnet coil, the current in a shorted turn must be opposed to the incident current. If the direction of the current in each conductor can be measured relative to the incident current, then the exact location of the short can be determined. In this device, an AC voltage is applied to the magnet under test. A small hand held B-dot pickup coil monitors the magnetic field produced by current in the individual magnet conductors. The relative phase of this pickup coil voltage is compared to a reference signal derived from the input current to detect a current reversal as the B-dot pickup coil is swept over the conductors of the coil under test. This technique however, is limited to only those conductors that are accessible to the hand held probe.

Dinkel, J.A.; Biggs, J.E.

1994-03-01T23:59:59.000Z

175

Uranium Mill Tailings Remedial Action Project (UMTRAP) Public Participation Plan  

SciTech Connect (OSTI)

The purpose of this Public Participation Plan is to explain the Department of Energy`s plan for involving the public in the decision-making process related to the Uranium Mill Tailings Remedial Action (UMTRA) Project. This project was authorized by Congress in the Uranium Mill Tailings Radiation Control Act of 1978. The Act provides for a cooperative effort with affected states and Indian tribes for the eventual cleanup of abandoned or inactive uranium mill tailings sites, which are located in nine western states and in Pennsylvania. Section 111 of the Act states, ``in carrying out the provisions of this title, including the designation of processing sites, establishing priorities for such sites, the selection of remedial actions and the execution of cooperative agreements, the Secretary (of Energy), the Administrator (of the Environmental Protection Agency), and the (Nuclear Regulatory) Commission shall encourage public participation and, where appropriate, the Secretary shall hold public hearings relative to such matters in the States where processing sites and disposal sites are located.`` The objective of this document is to show when, where, and how the public will be involved in this project.

NONE

1981-05-01T23:59:59.000Z

176

The role of short-rotation woody crops in sustainable development  

SciTech Connect (OSTI)

One answer to increase wood production is by increasing management intensity on existing timberland, especially in plantation forests. Another is to convert land currently in agriculture to timberland. Short-rotation woody crops can be used in both cases. But, what are the environmental consequences? Short-rotation woody crops can provide a net improvement in environmental quality at both local and global scales. Conversion of agricultural land to short-rotation woody crops can provide the most environmental quality enhancement by reducing erosion, improving soil quality, decreasing runoff, improving groundwater quality, and providing better wildlife habitat. Forest products companies can use increased production from intensively managed short-rotation woody crop systems to offset decreased yield from the portion of their timberland that is managed less intensively, e.g. streamside management zones and other ecologically sensitive or unique areas. At the global scale, use of short-rotation woody crops for bioenergy is part of the solution to reduce greenhouse gases produced by burning fossil fuels. Incorporating short-rotation woody crops into the agricultural landscape also increases storage of carbon in the soil, thus reducing atmospheric concentrations. In addition, use of wood instead of alternatives such as steel, concrete, and plastics generally consumes less energy and produces less greenhouse gases. Cooperative research can be used to achieve energy, fiber, and environmental goals. This paper will highlight several examples of ongoing cooperative research projects that seek to enhance the environmental aspects of short-rotation woody crop systems. Government, industry, and academia are conducting research to study soil quality, use of mill residuals, nutrients in runoff and groundwater, and wildlife use of short-rotation woody crop systems in order to assure the role of short-rotation crops as a sustainable way of meeting society`s needs.

Shepard, J.P. [National Council of the Paper Industry for Air and Stream Improvement, Medford, MA (United States); Tolbert, V.R. [Oak Ridge National Lab., TN (United States)

1996-12-31T23:59:59.000Z

177

DECENTRALIZING SEMICONDUCTOR CAPACITY PLANNING VIA INTERNAL MARKET COORDINATION  

E-Print Network [OSTI]

1 DECENTRALIZING SEMICONDUCTOR CAPACITY PLANNING VIA INTERNAL MARKET COORDINATION SULEYMAN KARABUK semiconductor manufacturer: marketing managers reserve capacity from manufacturing based on product demands, while attempting to maximize profit; manufacturing managers allocate capacity to competing marketing

Wu, David

178

Short-term energy outlook, quarterly projections, second quarter 1998  

SciTech Connect (OSTI)

The Energy Information Administration (EIA) prepares quarterly short-term energy supply, demand, and price projections. The details of these projections, as well as monthly updates, are available on the Internet at: www.eia.doe.gov/emeu/steo/pub/contents.html. The paper discusses outlook assumptions; US energy prices; world oil supply and the oil production cutback agreement of March 1998; international oil demand and supply; world oil stocks, capacity, and net trade; US oil demand and supply; US natural gas demand and supply; US coal demand and supply; US electricity demand and supply; US renewable energy demand; and US energy demand and supply sensitivities. 29 figs., 19 tabs.

NONE

1998-04-01T23:59:59.000Z

179

Abstract--This paper addresses the problem of interaction between short run and long run locational signals and the coordination between generation investments and lumpy transmission  

E-Print Network [OSTI]

. The short run locational signals we evaluate are sent by nodal pricing and the long run ones are sent-known marginal pricing to expand both generation and transmission capacity (Crew et al., 1995; Stoft, 2006). One the marginal transmission capacity cost with marginal congestion cost. Nodal pricing as market-based pricing

Paris-Sud XI, Université de

180

Representation of Solar Capacity Value in the ReEDS Capacity Expansion Model  

SciTech Connect (OSTI)

An important issue for electricity system operators is the estimation of renewables' capacity contributions to reliably meeting system demand, or their capacity value. While the capacity value of thermal generation can be estimated easily, assessment of wind and solar requires a more nuanced approach due to the resource variability. Reliability-based methods, particularly assessment of the Effective Load-Carrying Capacity, are considered to be the most robust and widely-accepted techniques for addressing this resource variability. This report compares estimates of solar PV capacity value by the Regional Energy Deployment System (ReEDS) capacity expansion model against two sources. The first comparison is against values published by utilities or other entities for known electrical systems at existing solar penetration levels. The second comparison is against a time-series ELCC simulation tool for high renewable penetration scenarios in the Western Interconnection. Results from the ReEDS model are found to compare well with both comparisons, despite being resolved at a super-hourly temporal resolution. Two results are relevant for other capacity-based models that use a super-hourly resolution to model solar capacity value. First, solar capacity value should not be parameterized as a static value, but must decay with increasing penetration. This is because -- for an afternoon-peaking system -- as solar penetration increases, the system's peak net load shifts to later in the day -- when solar output is lower. Second, long-term planning models should determine system adequacy requirements in each time period in order to approximate LOLP calculations. Within the ReEDS model we resolve these issues by using a capacity value estimate that varies by time-slice. Within each time period the net load and shadow price on ReEDS's planning reserve constraint signals the relative importance of additional firm capacity.

Sigrin, B.; Sullivan, P.; Ibanez, E.; Margolis, R.

2014-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Serbia-Enhancing Capacity for Low Emission Development Strategies...  

Open Energy Info (EERE)

Serbia-Enhancing Capacity for Low Emission Development Strategies (EC-LEDS) Jump to: navigation, search Name Serbia-Enhancing Capacity for Low Emission Development Strategies...

182

Guatemala-Enhancing Capacity for Low Emission Development Strategies...  

Open Energy Info (EERE)

Guatemala-Enhancing Capacity for Low Emission Development Strategies (EC-LEDS) Jump to: navigation, search Name Guatemala-Enhancing Capacity for Low Emission Development Strategies...

183

HT Combinatorial Screening of Novel Materials for High Capacity...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

HT Combinatorial Screening of Novel Materials for High Capacity Hydrogen Storage HT Combinatorial Screening of Novel Materials for High Capacity Hydrogen Storage Presentation for...

184

Expansion of Novolyte Capacity for Lithium Ion Electrolyte Production...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

15eswise2012p.pdf More Documents & Publications Expansion of Novolyte Capacity for Lithium Ion Electrolyte Production Expansion of Novolyte Capacity for Lithium Ion Electrolyte...

185

Expansion of Novolyte Capacity for Lithium Ion Electrolyte Production...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

15eswise2011p.pdf More Documents & Publications Expansion of Novolyte Capacity for Lithium Ion Electrolyte Production Expansion of Novolyte Capacity for Lithium Ion Electrolyte...

186

Solid-State Hydrogen Storage: Storage Capacity,Thermodynamics...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Hydrogen Storage: Storage Capacity,Thermodynamics and Kinetics. Solid-State Hydrogen Storage: Storage Capacity,Thermodynamics and Kinetics. Abstract: Solid-state reversible...

187

Design and Evaluation of Novel High Capacity Cathode Materials...  

Broader source: Energy.gov (indexed) [DOE]

Design and Evaluation of Novel High Capacity Cathode Materials Design and Evaluation of Novel High Capacity Cathode Materials 2009 DOE Hydrogen Program and Vehicle Technologies...

188

Design and Evaluation of Novel High Capacity Cathode Materials...  

Broader source: Energy.gov (indexed) [DOE]

and Evaluation of Novel High Capacity Cathode Materials Design and Evaluation of Novel High Capacity Cathode Materials 2012 DOE Hydrogen and Fuel Cells Program and Vehicle...

189

Study Finds 54 Gigawatts of Offshore Wind Capacity Technically...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Study Finds 54 Gigawatts of Offshore Wind Capacity Technically Possible by 2030 Study Finds 54 Gigawatts of Offshore Wind Capacity Technically Possible by 2030 September 11, 2014 -...

190

National CHP Roadmap: Doubling Combined Heat and Power Capacity...  

Broader source: Energy.gov (indexed) [DOE]

National CHP Roadmap: Doubling Combined Heat and Power Capacity in the United States by 2010, March 2001 National CHP Roadmap: Doubling Combined Heat and Power Capacity in the...

191

India-Vulnerability Assessment and Enhancing Adaptive Capacities...  

Open Energy Info (EERE)

Adaptive Capacities to Climate Change Jump to: navigation, search Name India-Vulnerability Assessment and Enhancing Adaptive Capacities to Climate Change AgencyCompany...

192

"Assessment of the Adequacy of Natural Gas Pipeline Capacity...  

Broader source: Energy.gov (indexed) [DOE]

"Assessment of the Adequacy of Natural Gas Pipeline Capacity in the Northeast United States" Report Now Available "Assessment of the Adequacy of Natural Gas Pipeline Capacity in...

193

Assessment of the Adequacy of Natural Gas Pipeline Capacity in...  

Broader source: Energy.gov (indexed) [DOE]

Assessment of the Adequacy of Natural Gas Pipeline Capacity in the Northeast United States - November 2013 Assessment of the Adequacy of Natural Gas Pipeline Capacity in the...

194

RULES FOR CONGESTION MANAGEMENT EVALUATION OF AVAILABILITY OF CAPACITY AND  

E-Print Network [OSTI]

RULES FOR CONGESTION MANAGEMENT EVALUATION OF AVAILABILITY OF CAPACITY AND POSSIBILITIES................................................................16 5.6 Socio-economic cost of guaranteed capacity

195

Heat capacity at the glass transition  

E-Print Network [OSTI]

A fundamental problem of glass transition is to explain the jump of heat capacity at the glass transition temperature $T_g$ without asserting the existence of a distinct solid glass phase. This problem is also common to other disordered systems, including spin glasses. We propose that if $T_g$ is defined as the temperature at which the liquid stops relaxing at the experimental time scale, the jump of heat capacity at $T_g$ follows as a necessary consequence due to the change of system's elastic, vibrational and thermal properties. In this picture, we discuss time-dependent effects of glass transition, and identify three distinct regimes of relaxation. Our approach explains widely observed logarithmic increase of $T_g$ with the quench rate and the correlation of heat capacity jump with liquid fragility.

Kostya Trachenko; Vadim Brazhkin

2010-07-13T23:59:59.000Z

196

Assessing leadership capacities in societal systems  

E-Print Network [OSTI]

As a society we are overwhelmed with metrics that drive a specific type of behavior: Short-term improvements in externally observable phenomena, such as wealth, sales and costs. This applies at all levels of society, from ...

Jaenicke, Allan (Allan H.)

2011-01-01T23:59:59.000Z

197

Low energy milling method, low crystallinity alloy, and negative electrode composition  

DOE Patents [OSTI]

A method of making nanostructured alloy particles includes milling a millbase in a pebble mill containing milling media. The millbase comprises: (i) silicon, and (ii) at least one of carbon or a transition metal, and wherein the nanostructured alloy particles are substantially free of crystalline domains greater than 50 nanometers in size. A method of making a negative electrode composition for a lithium ion battery including the nanostructured alloy particles is also disclosed.

Le, Dihn B; Obrovac, Mark N; Kube, Robert Y; Landucci, James R

2012-10-16T23:59:59.000Z

198

Energy Analysis of a Kraft Pulp Mill: Potential for Energy Efficiency and Advanced Biomass Cogeneration  

E-Print Network [OSTI]

to be energy self-sufficent (with excess energy as a potentially important by-product for export) requires , Permanent address: Departmenl of Environmental and Energy Systems Studies, Lund University, Lund, Sweden. " To whom all correspondence should... identified significant savings potentials. For example, one mill in Sweden uses 13-14 MMBtu per ADST of steam and has a process (;onfiguration similar to the mill studied here (23). Despite the already low steam consumption at the Swedish mill, a pin...

Subbiah, A.; Nilsson, L. J.; Larson, E. D.

199

Protocol for GL spin columns p10, 200ug capacity. p200, 600ug capacity.  

E-Print Network [OSTI]

Protocol for GL spin columns p10, 200ug capacity. p200, 600ug capacity. Glscienceinc.com product tips (exact protocol from GL Sciences): 1. Bring samples up in 65 uL of Buffer A. 2. Condition a. Add

Richardson, David

200

A study of freeway capacity in Texas  

E-Print Network [OSTI]

studies have been undertaken to determine the value of capacity. A study by Hurdle and Datta in 1983 concluded that the value of 2, 000 pcphpl was still a good estimate of capacity (5). In contrast, a study by Agyemang-Duah (6) concluded...). Many other studies have attempted to measure the flows in both conditions and have produced varying results. Another related issue is the requirement for the existence of sufficient demand which is highlighted by McShane and Roess (13). Agyemang-Duah...

Ringert, John Franklin

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

IMPROVING ENERGY EFFICIENCY VIA OPTIMIZED CHARGE MOTION AND SLURRY FLOW IN PLANT SCALE SAG MILLS  

SciTech Connect (OSTI)

The U.S. mining industry operates approximately 80 semi-autogenesis grinding mills (SAG) throughout the United States. Depending on the mill size the SAG mills draws between 2 MW and 17 MW. The product from the SAG mill is further reduced in size using pebble crushers and ball mills. Hence, typical gold or copper ore requires between 2.0 and 7.5 kWh per ton of energy to reduce the particle size. Considering a typical mining operation processes 10,000 to 100,000 tons per day the energy expenditure in grinding is 50 percent of the cost of production of the metal. A research team from the University of Utah is working to make inroads into saving energy in these SAG mills. In 2003, Industries of the Future Program of the Department of Energy tasked the University of Utah team to build a partnership between the University and the mining industry for the specific purpose of reducing energy consumption in SAG mills. A partnership was formed with Cortez Gold Mines, Kennecott Utah Copper Corporation, Process Engineering Resources Inc. and others. In the current project, Cortez Gold Mines played a key role in facilitating the 26-ft SAG mill at Cortez as a test mill for this study. According to plant personnel, there were a number of unscheduled shut downs to repair broken liners and the mill throughput fluctuated depending on ore type. The University team had two softwares, Millsoft and FlowMod to tackle the problem. Millsoft is capable of simulating the motion of charge in the mill. FlowMod calculates the slurry flow through the grate and pulp lifters. Based on this data the two models were fine-tuned to fit the Cortez SAG will. In the summer of 2004 a new design of shell lifters were presented to Cortez and in September 2004 these lifters were installed in the SAG mill. By December 2004 Cortez Mines realized that the SAG mill is drawing approximately 236-kW less power than before while maintaining the same level of production. In the first month there was extreme cycling and operators had to learn more. Now the power consumption is 0.3-1.3 kWh/ton lower than before. The actual SAG mill power draw is 230-370 kW lower. Mill runs 1 rpm lesser in speed on the average. The re-circulation to the cone crusher is reduced by 1-10%, which means more efficient grinding of critical size material is taking place in the mill. All of the savings have resulted in reduction of operating cost be about $0.023-$0.048/ ton.

Raj K. Rajamani; Sanjeeva Latchireddi; Sravan K. Prathy; Trilokyanath Patra

2005-12-01T23:59:59.000Z

202

Phase evolution in carbide dispersion strengthened nanostructured copper composite by high energy ball milling  

SciTech Connect (OSTI)

In this study, high-energy ball milling was applied to synthesis in situ nanostructured copper based composite reinforced with metal carbides. Cu, M (M=W or Ti) and graphite powder mixture were mechanically alloyed for various milling time in a planetary ball mill with composition of Cu-20vol%WC and Cu-20vol%TiC. Then the as-milled powder were compacted at 200 to 400 MPa and sintered in a vacuum furnace at 900 Degree-Sign C. The results of X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy analysis showed that formation of tungsten carbides (W{sub 2}C and WC phases) was observed after sintering of Cu-W-C mixture while TiC precipitated in as-milled powder of Cu-Ti-C composite after 5 h and become amorphous with longer milling. Mechanism of MA explained the cold welding and fracturing event during milling. Cu-W-C system shows fracturing event is more dominant at early stage of milling and W particle still existed after milling up to 60 h. While in Cu-Ti-C system, cold welding is more dominant and all Ti particles dissolved into Cu matrix.

Hussain, Zuhailawati; Nur Hawadah, M. S. [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia)

2012-09-06T23:59:59.000Z

203

E-Print Network 3.0 - assisted mechanical milling Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

nanotubes in effecting catalytic action... of Nanoporous Carbon Powders Produced by High Energy Ball Milling and Formation of Carbon Nanotubes During... DECMSRMP F-91191 Gif sur...

204

amorphous ball-milled powders: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

, and thermal properties of Nafion powders prepared by high-energy ball milling of pellets is given. Nafion powders prepared in this manner exhibit thermal behavior similar...

205

E-Print Network 3.0 - armoring uranium-mill tailings Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Donahue R, Hendry MJ, Landine P (2000b) Geochemistry of arsenic and nickel in uranium mill tailings... , Mahoney J, MacDonald A, Rowson J (1999) ... Source: Pichler,...

206

Longest-Serving Active Paper Mill in the Western United States...  

Broader source: Energy.gov (indexed) [DOE]

MMBtu and 379,000 annually after receiving a DOE energy assessment and implementing steam system improvement recommendations. Longest-Serving Active Paper Mill in the Western...

207

Robust capacity expansion solutions for telecommunication ...  

E-Print Network [OSTI]

networksX the ™osts of investment —nd the qu—lity of servi™e @ oƒA ...... Robust solutions with 1 ? ? for capacity constraints. Deterministic. Protection ...... tions networks under dem—nd un™ert—intyD in Proceedings of the 6th International.

2010-08-03T23:59:59.000Z

208

Building Environmental Health Capacity in Allegheny County  

E-Print Network [OSTI]

Building Environmental Health Capacity in Allegheny County: Environmental Indicators Outcomes standard Air Quality Computer Systems Days exceeding ozone standard Air Quality Computer Systems Attainment of the annual PM-2.5 standard (Fine particulates) Air Quality Computer Systems Annual PM-2.5 level Air Quality

209

PROJECT REPORT HVAC EQUIPMENT DEMOGRAPHICS AND CAPACITY  

E-Print Network [OSTI]

PROJECT REPORT HVAC EQUIPMENT DEMOGRAPHICS AND CAPACITY ANALYSIS TOOLS APPLICABLE TO MULTI Commercial HVAC Design Process 12 5.0 Conclusion 18 6.0 References 19 TABLE OF CONTENTS SECTIONS #12;MULTI performance by collectively improving the enve- lope, lighting and HVAC systems. The primary goals of the UC

California at Davis, University of

210

CSEM WP 124 Capacity Markets for Electricity  

E-Print Network [OSTI]

CSEM WP 124 Capacity Markets for Electricity Anna Creti, LEEERNA, University of Toulouse for Electricity Anna Creti LEEERNA, University of Toulouse Natalia Fabra Universidad Carlos III de Madrid February 2004 Abstract The creation of electricity markets has raised the fundamental question as to whether

California at Berkeley. University of

211

Multivariable controller increased MTBE complex capacity  

SciTech Connect (OSTI)

Capacity increased by more than 4.6% when one dynamic matrix multivariable controller began operating in Valero Refining Company`s MTBE production complex in Corpus Christi, Texas. This was on a plant that was already running well above design capacity due to previously made process changes. A single controller was developed to cover an isobutane dehydrogenation (ID) unit and an MTBE reaction and fractionation plant with the intermediate isobutylene surge drum. The overall benefit is realized by a comprehensive constrained multivariable predictive controller that properly handles all sets of limits experienced by the complex, whether limited by the front-end ID or back-end MTBE units. The controller has 20 manipulated, 6 disturbance and 44 controlled variables, and covers widely varying dynamics with settling times ranging from twenty minutes to six hours. The controller executes each minute with a six hour time horizon. A unique achievement is intelligent surge drum level handling by the controller for higher average daily complex capacity as a whole. The ID unit often operates at simultaneous limits on reactor effluent compressor capacity, cold box temperature and hydrogen/hydrocarbon ratio, and the MTBE unit at impurity in butene column overhead as well as impurity in MTBE product. The paper discusses ether production, isobutane dehydrogenation, maximizing production, controller design, and controller performance.

Robertson, D.; Peterson, T.J.; O`Connor, D. [DMC Corp., Houston, TX (United States); Payne, D.; Adams, V. [Valero Refining Co., Corpus Christi, TX (United States)

1997-03-01T23:59:59.000Z

212

Information Capacity of Energy Harvesting Sensor Nodes  

E-Print Network [OSTI]

Information Capacity of Energy Harvesting Sensor Nodes R Rajesh CABS, DRDO Bangalore, India Email: rajesh81r@gmail.com Vinod Sharma Dept. of ECE Indian Institute of Science Bangalore, India Email: vinod Email: pramodv@uiuc.edu Abstract--Sensor nodes with energy harvesting sources are gaining popularity due

Sharma, Vinod

213

Partial energies fluctuations and negative heat capacities  

E-Print Network [OSTI]

We proceed to a critical examination of the method used in nuclear fragmentation to exhibit signals of negative heat capacity. We show that this method leads to unsatisfactory results when applied to a simple and well controlled model. Discrepancies are due to incomplete evaluation of potential energies.

Xavier Campi; H. Krivine; E. Plagnol; N. Sator

2004-08-03T23:59:59.000Z

214

Kampung Capacity Local Solutions for Sustainable  

E-Print Network [OSTI]

Kampung Capacity Local Solutions for Sustainable Rural Energy in the Baram River Basin, Sarawak for the river basin. Keywords: South East Asia, Malaysia, Rural Energy Access, Local Solutions #12;RAEL Report, Malaysia Rebekah Shirley Daniel Kammen University of California ­ Berkeley Renewable and Appropriate Energy

Kammen, Daniel M.

215

Capacity Building in Wind Energy for PICs  

E-Print Network [OSTI]

indicates that significant wind energy potential exists. · A monitoring project showed that in Rarotonga system. · About 30 other islands could have potential for grid connected wind turbines in the 100-1000 k1 Capacity Building in Wind Energy for PICs Presentation of the project Regional Workshop Suva

216

Constrained capacity of MIMO Rayleigh fading channels  

E-Print Network [OSTI]

In this thesis channel capacity of a special type of multiple-input multiple-output (MIMO) Rayleigh fading channels is studied, where the transmitters are subject to a finite phase-shift keying (PSK) input alphabet. The constraint on the input...

He, Wenyan

2011-08-08T23:59:59.000Z

217

Uranium mine and mill tailings - Liabilities in the European Union  

SciTech Connect (OSTI)

Available in abstract form only. Full text of publication follows: Uranium mining and milling has taken place on large scale in the Member States of the European Union (EU) for some 60 years. Although, compared to mining, milling activities are normally concentrated in fewer locations, this can still result in a relatively large number of disposal sites for the tailings, compared to other radioactive wastes. In addition these sites are also quite large, in terms of both volume and surface area. Coupled with the residual uranium in the tailings together with other radionuclides, heavy metals, chemicals etc this results in an environmental legacy continuing far into the future. Often during production no or little provision has been made for the closure, remediation and future supervision of such sites. In 1996 the European Commission funded an inventory of uranium mining and milling liabilities in nine Central and Eastern European Countries. Additionally, pilot projects were funded to carry out remediation activities at several sites. Almost ten years later the Commission has identified the need to address the situation of these large liabilities in all EU Member States and to assess the progress made in remediation of the sites, especially in view of the closure of almost all mining activities in Europe. The Commission study has identified the current tailings liabilities in Europe, their status, the future plans for these sites and the hazards that continue to be associated with them. It is clear that although considerable progress has been made in recent years, much work remains to be carried out in the areas of remediation, and ensuring the long-term safety of many of the identified objects. The paper presents the main findings of the study, as well as the challenges identified to ensure long-term safety of these wastes. (authors)

Hilden, Wolfgang; Murphy, Simon [European Commission, Maison de l'Europe, L-2920 (Luxembourg); Vrijen, Jan [KARUWEEG BV, Leliendaalsedreef 9, 4333 JZ Middelburg (Netherlands)

2007-07-01T23:59:59.000Z

218

Monticello Mill Tailings Site environmental report for calendar year 1992  

SciTech Connect (OSTI)

This report contains information pertaining to environmental activities conducted during calendar year 1992 at and near the inactive uranium millsite in Monticello, Utah. Environmental activities conducted at the Monticello Mill Tailings Site (MMTS) during 1992 included those associated with remedial action and compliance monitoring. Compliance monitoring consisted of both radiological and nonradiological monitoring of air, surface water, and ground water. Radiological and nonradiological air monitoring at the MMTS included measurements of atmospheric radon, particulate matter, and gamma radiation. Air particulate monitoring for radiological and nonradiological constituents was conducted at one location on and two locations off the millsite with high-volume particulate samplers. The maximum airborne concentrations of radium-226, thorium-230, and total uranium at all locations were several orders of magnitude below the regulatory limits specified by DOE Order 5400.5. Surface water monitoring included water quality measurements within Montezuma Creek. During 1992, maximum levels of selenium; gross alpha, gross beta, total dissolved solids, and iron exceeded their respective state standards in one or more samples collected from upstream, on-site, and downstream locations. Ground-water monitoring was conducted for two aquifers underlying the millsite. The shallow aquifer is contaminated by leached products of uranium mill tailings. During 1992, Uranium Mill Tailings Radiation Control Act and state of Utah ground-water standards for arsenic, barium, nitrate, chromium, lead, selenium, molybdenum, uranium-234 and -238, gross alpha particle activity, and radium-226 and -228 were exceeded in one or more alluvial wells. This well will continue to be sampled to determine if the presence of these constituents was anomalous or if the measurements represented contamination in the aquifer.

Not Available

1993-05-01T23:59:59.000Z

219

Wireless Network Capacity Management: A Real Options Approach  

E-Print Network [OSTI]

capacity, market price of risk, investment timing option 1 Introduction Wireless networks are now regarded

Forsyth, Peter A.

220

TURKEY'S CIVILIAN CAPACITY IN POST-CONFLICT RECONSTRUCTION  

E-Print Network [OSTI]

TURKEY'S CIVILIAN CAPACITY IN POST-CONFLICT RECONSTRUCTION 1 TURKEY'S CIVILIAN CAPACITY IN POST-CONFLICT RECONSTRUCTION by Teri Murphy & Onur Sazak #12;Turkey's Civilian Capacity in post-Conflict Reconstruction By Teri-checking was indispensable for the realization of this project. #12;TURKEY'S CIVILIAN CAPACITY IN POST

Yanikoglu, Berrin

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

SHORT REVIEW Butterfly genomics eclosing  

E-Print Network [OSTI]

SHORT REVIEW Butterfly genomics eclosing P Beldade1 , WO McMillan2 and A Papanicolaou3 1 Section to an explosion of genomic data and the emergence of new research avenues. Evolutionary and ecological functional genomics, with its focus on the genes that affect ecological success and adaptation in natural populations

Beldade, Patrícia

222

Electromagnetic neutrino: a short review  

E-Print Network [OSTI]

A short review on selected issues related to the problem of neutrino electromagnetic properties is given. After a flash look at the theoretical basis of neutrino electromagnetic form factors, constraints on neutrino magnetic moments and electric millicharge from terrestrial experiments and astrophysical observations are discussed. We also focus on some recent studies of the problem and on perspectives.

Alexander I. Studenikin

2014-11-09T23:59:59.000Z

223

University Policy Process Short Version  

E-Print Network [OSTI]

Rev. 5/09 University Policy Process Short Version Conduct Analysis Draft Documents Get Approvals. Identify policy owner 3. Assemble team 4. Engage Stakeholders 5. Draft policy 6. Submit proposed policy approves (or not) Do we need a policy? 11. Plan communication & training 12. UPO posts approved policy

Mohanty, Saraju P.

224

Uranium Mill Tailings Remedial Action Project Environmental Protection Implementation Plan  

SciTech Connect (OSTI)

The Uranium Mill Tallings Remedial Action (UMTRA) Project Environmental Protection Implementation Plan (EPIP) has been prepared in accordance with the requirements of the US Department of Energy (DOE) Order 5400.1 (Chapter 3, paragraph 2). The UMTRA EPIP covers the time period of November 9, 1992, through November 8, 1993. It will be updated annually. Its purpose is to provide management direction to ensure that the UMTRA Project is operated and managed in a manner that will protect, maintain, and where necessary, restore environmental quality, minimize potential threats to public health and the environment, and comply with environmental regulations and DOE policies.

Not Available

1992-10-01T23:59:59.000Z

225

Uranium Mill Tailings Remedial Action Project environmental protection implementation plan  

SciTech Connect (OSTI)

The Uranium Mill Tailings Remedial Action (UMTRA) Project Environmental Protection Implementation Plan (EPIP) has been prepared in accordance with the requirements of the U.S. Department of Energy (DOE) Order 5400.1. The UMTRA EPIP is updated annually. This version covers the time period of 9 November 1994, through 8 November 1995. Its purpose is to provide management direction to ensure that the UMTRA Project is operated and managed in a manner that will protect, maintain, and where necessary, restore environmental quality, minimize potential threats to public health and the environment, and comply with environmental regulations and DOE policies.

Not Available

1994-10-01T23:59:59.000Z

226

Uranium Mill Tailings Remedial Action Project. 1995 Environmental Report  

SciTech Connect (OSTI)

In accordance with U.S. Department of Energy (DOE) Order 23 1. 1, Environment, Safety and Health Reporting, the DOE prepares an annual report to document the activities of the Uranium Mill Tailings Remedial Action (UMTRA) Project environmental monitoring program. This monitoring must comply with appropriate laws, regulations, and standards, and it must identify apparent and meaningful trends in monitoring results. The results of all monitoring activities must be communicated to the public. The UMTRA Project has prepared annual environmental reports to the public since 1989.

NONE

1996-06-01T23:59:59.000Z

227

Classical paths for Yang-Mills field with fixed energy  

E-Print Network [OSTI]

A new classical solution for the SU(2) Yang-Mills theory, in which the Euclidean energy plays a role of a parameter is found. A correspondence between this solution and the known selfdual multi-instanton configuration, which has the topological charge N, is discussed, the number of parameters governing the new solution is found to be 8N+1. For negative energies the new solution is periodic in Euclidean time, for positive energies it exhibits the effect of localization, which states that the solution is completely described within a finite interval of time, for zero energy the found solution is reduced to a selfdual one.

Michael Kuchiev

2009-04-19T23:59:59.000Z

228

Neumann domination for the Yang-Mills heat equation  

E-Print Network [OSTI]

Long time existence and uniqueness of solutions to the Yang-Mills heat equation have been proven over a compact 3-manifold with boundary for initial data of finite energy. In the present paper we improve on previous estimates by using a Neumann domination technique that allows us to get much better pointwise bounds on the magnetic field. As in the earlier work, we focus on Dirichlet, Neumann and Marini boundary conditions. In addition, we show that the Wilson Loop functions, gauge invariantly regularized, converge as the parabolic time goes to infinity.

Nelia Charalambous; Leonard Gross

2014-05-30T23:59:59.000Z

229

East Millinocket Mill Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump37. It is classified asThis article isMcKeesport is a boroughMillinocket Mill

230

Dry milling properties of selected sorghum grain varieties  

E-Print Network [OSTI]

abrasive grinding, sifting and air flotation techniques. Milling was accomplished with a Strong ? Scott laboratory barley peatier which was modified by sub- stitut?ng a wire brush for the carborundum wheel. T??e wire brush was 6 inches in diameter and 2... seconds in the Strong-Scott barley pearler equipped wi. th a carborundum wheel. The hardness value was the per- cent of sample retained on a U. S. No. 12 Sieve. Test weight of all varieties was determined using standard equipment and procedures (24...

Krishnaprasad, Mittur Nanjappa

1970-01-01T23:59:59.000Z

231

Mill Valley, California: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 -Energieprojekte GmbH JumpSprings, Vermont:is a town inInformationMililaniMill

232

Mille Lacs County, Minnesota: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 -Energieprojekte GmbH JumpSprings, Vermont:is a townMillard County,Millbury isMille

233

DOE - Office of Legacy Management -- Loma Mill - CO 03  

Office of Legacy Management (LM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment ofDepartment ofof EnergyYou are here HomeGunnison- NYLelandLoma Mill - CO 03

234

DOE - Office of Legacy Management -- Lowman Mill Site - ID 01  

Office of Legacy Management (LM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment ofDepartment ofof EnergyYou are here HomeGunnison- NYLelandLoma Mill

235

Kemp Mill, Maryland: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429 Throttled (botOpen6 ClimateKamas,Kelsey North Geothermal ProjectKemp Mill,

236

Spring Mills, Pennsylvania: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov Pty Ltd JumpGTZHolland, Illinois:5717551°FarmsSESLogMills is a census-designated

237

MEASUREMENT OF SPECIFIC HEAT CAPACITY OF SALTSTONE  

SciTech Connect (OSTI)

One of the goals of the Saltstone variability study is to identify (and quantify the impact of) the operational and compositional variables that control or influence the important processing and performance properties of Saltstone grout mixtures. The heat capacity of the Saltstone waste form is one of the important properties of Saltstone mixes that was last measured at SRNL in 1997. It is therefore important to develop a core competency for rapid and accurate analysis of the specific heat capacity of the Saltstone mixes in order to quantify the impact of compositional and operational variations on this property as part of the variability study. The heat capacity, coupled with the heat of hydration data obtained from isothermal calorimetry for a given Saltstone mix, can be used to predict the maximum temperature increase in the cells within the vaults of the Saltstone Disposal Facility (SDF). The temperature increase controls the processing rate and the pour schedule. The maximum temperature is also important to the performance properties of the Saltstone. For example, in mass pours of concrete or grout of which Saltstone is an example, the maximum temperature increase and the maximum temperature difference (between the surface and the hottest location) are controlled to ensure durability of the product and prevent or limit the cracking caused by the thermal gradients produced during curing. This report details the development and implementation of a method for the measurement of the heat capacities of Saltstone mixes as well as the heat capacities of the cementitious materials of the premix and the simulated salt solutions used to batch the mixes. The developed method utilizes the TAM Air isothermal calorimeter and takes advantage of the sophisticated heat flow measurement capabilities of the instrument. Standards and reference materials were identified and used to validate the procedure and ensure accuracy of testing. Heat capacities of Saltstone mixes were {approx} 55% higher than the previous measurement of specific heat capacity on a reference Saltstone mix in 1997. Values of mixes prepared using Deliquification, Dissolution and Adjustment (DDA), Modular Caustic Side Solvent Extraction Unit (MCU) and Salt Waste Processing Facility (SWPF) simulants and premix at 0.60 w/cm ratio were {approx} 1.95 J/g/{sup o}C and were equivalent within experimental error. The simple law of mixtures was used to predict the heat capacities of the Saltstone and the results were in excellent agreement with experimental data. This simple law of mixtures can therefore be used to predict the heat capacities of Saltstone mixes in those cases where measurements have not been made. The time dependence of the heat capacity is important as an input to the modeling of temperature increase in Saltstone vaults. The heat capacity of a mix of MCU and premix at 0.60 w/cm ratio was measured immediately after initial mixing and then periodically up to times greater than 100 days. Within experimental error, the heat capacity did not change with time. Therefore, the modeling is not complicated by requiring a time dependent function for specific heat capacity. The water to cementitious material (w/cm) ratio plays a key role in determining the value of the heat capacity. Both experimental and predictive values for SWPF mixes as function of the w/cm ratio were obtained and presented in this report. Predictions of the maximum temperatures of the Saltstone mixes were made using the heat of hydration data from previous isothermal measurements and the newly measured heat capacities for DDA, MCU and SWPF mixes. The maximum temperature increase ranged from 37 to 48 C for these mixes. The presence of aluminate at 0.33 M produced a temperature increase of 68 C which is close to the adiabatic temperature rise of 74 C observed by Steimke and Fowler in 1997 for a mix containing 0.35 M aluminate. Aluminum dissolution of the sludge will increase the aluminate in the DSS which in turn will result in a larger temperature increase in the Saltstone vaults during the curing p

Harbour, J; Vickie Williams, V

2008-09-29T23:59:59.000Z

238

Setting in the Modern Short Story  

E-Print Network [OSTI]

. Thompson , D~'I G. The Ph1losophY ot Fiation. Lo on" l8~. Wh1tcomb , S. L. st of th Novei . Boston, 1 ·5. II. II. L short-starl: AI 'bright, ].'velyn 1La.Y . Tltle Short story. N. Y., 1 O? Barrett , Chas. P. Short story Writing . N. ., 188. Canby... . III. Matthews, Brander . The Short - st ory. N. :x.., 1 07 . Patton, Wm. International Short-stori e , 2 vols • • Y., 1 ~lO. Short-stor y Classios--Amerlcan , 5 vols ., N. Y. t 1':;)05 . , , Short-story Clas8~cs--Foreign , 5 vole . N. ¥ . ! II...

Hodgson, Elizabeth

1913-06-05T23:59:59.000Z

239

Experimental and computational investigation of end-milling and development of a simulation model describing the machining process  

E-Print Network [OSTI]

1 Experimental and computational investigation of end-milling and development of a simulation model simulation model, which allows the selection of optimum cutting conditions in end-milling processes, taking

Aristomenis, Antoniadis

240

Timber Mills Closures and Procurement Zones Characteristics: Is there a Link?  

E-Print Network [OSTI]

.S. Forest Products Economic Importance China, Russia, 10% Brazil, 6% World's Major Industrial Roundwood Sustainable Timber Supply to existing Mills · Procurement zone characteristics ­ Landownership1, 2, 9 ­ Level, 2, 10 ­ Distance to mills8, 13 · Increased demand products & services ­ New industry (biofuels)4

Gray, Matthew

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Prediction of the tool displacement for robot milling applications using coupled models of an industrial  

E-Print Network [OSTI]

. INTRODUCTION The major fields of machining applications for industrial robots are automated pre- machining an industrial robot for milling applications inaccuracies of the serial robot kinematic, the low structuralPrediction of the tool displacement for robot milling applications using coupled models

Stryk, Oskar von

242

Sociologically imagined: the decentering of C. Wright Mills, the postmodern cowboy  

E-Print Network [OSTI]

SOCIOLOGICALLY IMAGINED: THE DECENTERING OF C. WRIGHT MILLS, THE POSTMODERN COWBOY A Dissertation by KEITH KERR Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of DOCTOR OF PHILOSOPHY May 2007 Major Subject: Sociology SOCIOLOGICALLY IMAGINED: THE DECENTERING OF C. WRIGHT MILLS, THE POSTMODERN COWBOY A Dissertation by KEITH KERR Submitted...

Kerr, Keith Thomas

2009-05-15T23:59:59.000Z

243

Fine root growth in a sweet chestnut (Castanea sativa Mill.) coppice  

E-Print Network [OSTI]

Fine root growth in a sweet chestnut (Castanea sativa Mill.) coppice P. Montpied Laboratoire d of a sweet chestnut (Castanea sativa Mill.) coppice. The aim of this study was to examine fine root phenology of a chestnut coppice with an emphasis on the influence of coppicing. Materials and Methods This study took

Paris-Sud XI, Université de

244

Energy Efficiency Opportunities for Small to Medium Sized Paper and Paperboard Mills  

E-Print Network [OSTI]

supply and some from on site wells. The machine i driven by a steam engine, and a backpressure turbi e generates power dedicated to a group of electric driven machines. Mill F. A newsprint paper mill in the urban southwest. AII furnish derived from...

Zacuto, P. J.

245

Radon attenuation handbook for uranium mill tailings cover design  

SciTech Connect (OSTI)

This handbook has been prepared to facilitate the design of earthen covers to control radon emission from uranium mill tailings. Radon emissions from bare and covered uranium mill tailings can be estimated from equations based on diffusion theory. Basic equations are presented for calculating surface radon fluxes from covered tailings, or alternately, the cover thicknesses required to satisfy a given radon flux criterion. Also described is a computer code, RAECOM, for calculating cover thicknesses and surface fluxes. Methods are also described for measuring diffusion coefficients for radon, or for estimating them from empirical correlations. Since long-term soil moisture content is a critical parameter in determining the value of the diffusion coefficient, methods are given for estimating the long-term moisture contents of soils. The effects of cover defects or advection are also discussed and guidelines are given for determining if they are significant. For most practical cases, advection and cover defect effects on radon flux can be neglected. Several examples are given to demonstrate cover design calculations, and an extensive list of references is included. 63 references, 18 figures, 6 tables.

Rogers, V.C.; Nielson, K.K.; Kalkwarf, D.R.

1984-04-01T23:59:59.000Z

246

UMTRA -- The US Uranium Mill Tailings Remedial Action Project  

SciTech Connect (OSTI)

In the late 1970s, the United States (US) established the first comprehensive regulatory structure for the management, disposal, and long-term care of wastes produced from its domestic uranium processing industry. This regulatory framework was established through the passage of the Uranium Mill Tailings Radiation Control Act of 1978, often referred to as UMTRCA. This legislation created the Uranium Mill Tailings Remedial Action (UMTRA) Project and assigned the US Department of Energy (DOE) the lead in conducting the required remedial action at 24 designated inactive uranium ore processing sites. With the majority of these 22 sites complete, the DOE`s UMTRA Project has established a distinguished reputation for safely and effectively remediating these low-level waste sites in a complex regulatory and socioeconomic environment. This paper describes the past accomplishments and current status of the UMTRA Project and discusses the DOE`s plans for addressing ground water contamination associated with these sites and its commitment to continuing the long-term care and management of these disposal cells.

Lightner, R. [Dept. of Energy, Washington, DC (United States); Cormier, C. [Department of Energy, Albuquerque, NM (United States); Bierley, D. [Roy F. Weston, Inc., Albuquerque, NM (United States)

1995-12-31T23:59:59.000Z

247

UMTRA (Uranium Mill Tailings Remedial Action) Project site management manual  

SciTech Connect (OSTI)

The purpose of this manual is to summarize the organizational interfaces and the technical approach used to manage the planning, design development, National Environmental Policy Act (NEPA) compliance, engineering, and remedial action required to stabilize and control the designated Uranium Mill Tailings Remedial Action (UMTRA) Project sites. This manual describes the Project's objective, participants' roles and responsibilities, technical approach for accomplishing the objective, and planning and managerial controls to be used in performing the site work. The narrative follows the flow of activities depicted in Figure 1.1, which provides the typical sequence of key Project activities. A list of acronyms used is presented at the end of the manual. The comparable manual for UMTRA Project vicinity properties is the Vicinity Properties Management and Implementation Manual'' (VPMIM) (UMTRA-DOE/AL-050601). Together, the two manuals cover the remedial action activities associated with UMTRA Project sites. The UMTRA Project's objective is to stabilize and control the uranium mill tailings, vicinity property materials, and other residual radioactive materials at the designated sites (Figure 1.2) in a safe and environmentally sound manner in order to minimize radiation health hazards to the public. 26 figs., 6 tabs.

Not Available

1990-10-01T23:59:59.000Z

248

Yang-Mills correlators at finite temperature: A perturbative perspective  

E-Print Network [OSTI]

We consider the two-point correlators of Yang-Mills theories at finite temperature in the Landau gauge. We employ a model for the corresponding Yang-Mills correlators based on the inclusion of an effective mass term for gluons. The latter is expected to have its origin in the existence of Gribov copies. One-loop calculations at zero temperature have been shown to agree remarkably well with the corresponding lattice data. We extend on this and perform a one-loop calculation of the Matsubara gluon and ghost two-point correlators at finite temperature. We show that, as in the vacuum, an effective gluon mass accurately captures the dominant infrared physics for the magnetic gluon and ghost propagators. It also reproduces the gross qualitative features of the electric gluon propagator. In particular, we find a slight nonmonotonous behavior of the Debye mass as a function of temperature, however not as pronounced as in existing lattice results. A more quantitative description of the electric sector near the deconfinement phase transition certainly requires another physical ingredient sensitive to the order parameter of the transition.

U. Reinosa; J. Serreau; M. Tissier; N. Wschebor

2014-05-12T23:59:59.000Z

249

Kuwait pressing toward preinvasion oil production capacity  

SciTech Connect (OSTI)

Oil field reconstruction is shifting focus in Kuwait as the country races toward prewar production capacity of 2 million b/d. Oil flow last month reached 1.7 million b/d, thanks largely to a massive workover program that has accomplished about as much as it can. By midyear, most of the 19 rigs in Kuwait will be drilling rather than working over wells vandalized by retreating Iraqi troops in February 1991. Seventeen gathering centers are at work, with capacities totaling 2.4 million b/d, according to state-owned Kuwait Oil Co. (KOC). This article describes current work, the production infrastructure, facilities strategy, oil recovery, well repairs, a horizontal pilot project, the drilling program, the constant reminders of war, and heightened tensions.

Tippee, B.

1993-03-15T23:59:59.000Z

250

Regulatory impact analysis of final environmental standards for uranium mill tailings at active sites  

SciTech Connect (OSTI)

The Environmental Protection Agency was directed by Congress, under PL 95-604, the Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA), to set standards of general application that provide protection from the hazards associated with uranium mill tailings. Title II of the Act requires standards covering the processing and disposal of byproduct materials at mills which are currently licensed by the appropriate regulatory authorities. This Regulatory Impact Analysis (RIA) addresses the standards promulgated under Title II. There are two major parts of the standards for active mills: standards for control of releases from tailings during processing operations and prior to final disposal, and standards for protection of the public health and environment after the disposal of tailings. This report presents a detailed analysis of standards for disposal only, since the analysis required for the standards during mill operations is very limited.

Not Available

1983-09-01T23:59:59.000Z

251

Calculations of Heat-Capacities of Adsorbates  

E-Print Network [OSTI]

PHYSICAL REVIEW B VOLUME 14, NUMBER 7 1 OCTOBER 1976 Calculations of heat capacities of adsorbates W. R. Lawrence and R. E. Allen Department of Physics, Texas A& M University, College Station, Texas 77843 (Received 2 September 1975) The phonon... the substrate has a perfect (100) surface and the adsorbate goes down as a solid monolayer in registry with the substrate. The quasiharmonic approximation was used, and the results for Ne adsorbates were considerably different from those obtained...

LAWRENCE, WR; Allen, Roland E.

1976-01-01T23:59:59.000Z

252

Property:MeanCapacity | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating Solar Powerstories onFocusOskiPhilipspresentsGeothermalAreaMeanCapacity Jump to:

253

A kinematic wave theory of capacity drop  

E-Print Network [OSTI]

Capacity drop at active bottlenecks is one of the most puzzling traffic phenomena, but a thorough understanding is practically important for designing variable speed limit and ramp metering strategies. In this study, we attempt to develop a simple model of capacity drop within the framework of kinematic wave theory based on the observation that capacity drop occurs when an upstream queue forms at an active bottleneck. In addition, we assume that the fundamental diagrams are continuous in steady states. This assumption is consistent with observations and can avoid unrealistic infinite characteristic wave speeds in discontinuous fundamental diagrams. A core component of the new model is an entropy condition defined by a discontinuous boundary flux function. For a lane-drop area, we demonstrate that the model is well-defined, and its Riemann problem can be uniquely solved. We theoretically discuss traffic stability with this model subject to perturbations in density, upstream demand, and downstream supply. We clarify that discontinuous flow-density relations, or so-called "discontinuous" fundamental diagrams, are caused by incomplete observations of traffic states. Theoretical results are consistent with observations in the literature and are verified by numerical simulations and empirical observations. We finally discuss potential applications and future studies.

Wen-Long Jin; Qi-Jian Gan; Jean-Patrick Lebacque

2013-10-09T23:59:59.000Z

254

Systematic evaluation of satellite remote sensing for identifying uranium mines and mills.  

SciTech Connect (OSTI)

In this report, we systematically evaluate the ability of current-generation, satellite-based spectroscopic sensors to distinguish uranium mines and mills from other mineral mining and milling operations. We perform this systematic evaluation by (1) outlining the remote, spectroscopic signal generation process, (2) documenting the capabilities of current commercial satellite systems, (3) systematically comparing the uranium mining and milling process to other mineral mining and milling operations, and (4) identifying the most promising observables associated with uranium mining and milling that can be identified using satellite remote sensing. The Ranger uranium mine and mill in Australia serves as a case study where we apply and test the techniques developed in this systematic analysis. Based on literature research of mineral mining and milling practices, we develop a decision tree which utilizes the information contained in one or more observables to determine whether uranium is possibly being mined and/or milled at a given site. Promising observables associated with uranium mining and milling at the Ranger site included in the decision tree are uranium ore, sulfur, the uranium pregnant leach liquor, ammonia, and uranyl compounds and sulfate ion disposed of in the tailings pond. Based on the size, concentration, and spectral characteristics of these promising observables, we then determine whether these observables can be identified using current commercial satellite systems, namely Hyperion, ASTER, and Quickbird. We conclude that the only promising observables at Ranger that can be uniquely identified using a current commercial satellite system (notably Hyperion) are magnesium chlorite in the open pit mine and the sulfur stockpile. Based on the identified magnesium chlorite and sulfur observables, the decision tree narrows the possible mineral candidates at Ranger to uranium, copper, zinc, manganese, vanadium, the rare earths, and phosphorus, all of which are milled using sulfuric acid leaching.

Blair, Dianna Sue; Stork, Christopher Lyle; Smartt, Heidi Anne; Smith, Jody Lynn

2006-01-01T23:59:59.000Z

255

Theory of SEI Formation in Rechargeable Batteries: Capacity Fade, Accelerated Aging and Lifetime Prediction  

E-Print Network [OSTI]

Cycle life is critically important in applications of rechargeable batteries, but lifetime prediction is mostly based on empirical trends, rather than mathematical models. In practical lithium-ion batteries, capacity fade occurs over thousands of cycles, limited by slow electrochemical processes, such as the formation of a solid-electrolyte interphase (SEI) in the negative electrode, which compete with reversible lithium intercalation. Focusing on SEI growth as the canonical degradation mechanism, we show that a simple single-particle model can accurately explain experimentally observed capacity fade in commercial cells with graphite anodes, and predict future fade based on limited accelerated aging data for short times and elevated temperatures. The theory is extended to porous electrodes, predicting that SEI growth is essentially homogeneous throughout the electrode, even at high rates. The lifetime distribution for a sample of batteries is found to be consistent with Gaussian statistics, as predicted by th...

Pinson, Matthew B

2012-01-01T23:59:59.000Z

256

DESIGN, PERFORMANCE, AND SUSTAINABILITY OF ENGINEERED COVERS FOR URANIUM MILL TAILINGS  

SciTech Connect (OSTI)

Final remedies at most uranium mill tailings sites include engineered covers designed to contain metals and radionuclides in the subsurface for hundreds of years. Early cover designs rely on compacted soil layers to limit water infiltration and release of radon, but some of these covers inadvertently created habitats for deep-rooted plants. Root intrusion and soil development increased the saturated hydraulic conductivity several orders of magnitude above design targets. These covers may require high levels of maintenance to sustain long-term performance. Relatively low precipitation, high potential evapotranspiration, and thick unsaturated soils favor long-term hydrologic isolation of buried waste at arid and semiarid sites. Later covers were designed to mimic this natural soil-water balance with the goal of sustaining performance with little or no maintenance. For example, the cover for the Monticello, Utah, Superfund site relies on a thick soil-sponge layer overlying a sand-and-gravel capillary barrier to store precipitation while plants are dormant and on native vegetation to dry the soil sponge during the growing season. Measurements of both off-site caisson lysimeters and a large 3-ha lysimeter built into the final cover show that drainage has been well below a U.S. Environmental Protection Agency target of less than 3.0 mm/yr. Our stewardship strategy combines monitoring precursors to failure, probabilistic riskbased modeling, and characterization of natural analogs to project performance of covers for a range of possible future environmental scenarios. Natural analogs are needed to understand how ecological processes will influence cover performance, processes that cannot be predicted with short-term monitoring and existing numerical models.

Waugh, W. Jody

2004-04-21T23:59:59.000Z

257

Uranium Mill Tailings Remedial Action Project Environmental Protection Implementation Plan  

SciTech Connect (OSTI)

The Uranium Mill Tailings Remedial Action (UMTRA) Project Environmental Protection Implementation Plan (EPIP) has been prepared in accordance with the requirements of the US Department of Energy (DOE) Order 5400.1. The UMTRA EPIP covers the time period of November 9, 1993, through November 8, 1994. It will be updated annually. Its purpose is to provide management direction to ensure that the UMTRA Project is operated and managed in a manner that will protect, maintain, and where necessary, restore environmental quality, minimize potential threats to public health and the environment, and comply with environmental regulations and DOE policies. Contents of this report are: (1) general description of the UMTRA project environmental protection program; (2) notifications; (3) planning and reporting; (4) special programs; (5) environmental monitoring programs; (6) quality assurance and data verification; and (7) references.

Vollmer, A.T.

1993-10-01T23:59:59.000Z

258

Uranium Mill Tailings Remedial Action Project 1993 Environmental Report  

SciTech Connect (OSTI)

This annual report documents the Uranium Mill Tailing Remedial Action (UMTRA) Project environmental monitoring and protection program. The UMTRA Project routinely monitors radiation, radioactive residual materials, and hazardous constituents at associated former uranium tailings processing sites and disposal sites. At the end of 1993, surface remedial action was complete at 10 of the 24 designated UMTRA Project processing sites. In 1993 the UMTRA Project office revised the UMTRA Project Environmental Protection Implementation Plan, as required by the US DOE. Because the UMTRA Project sites are in different stages of remedial action, the breadth of the UMTRA environmental protection program differs from site to site. In general, sites actively undergoing surface remedial action have the most comprehensive environmental programs for sampling media. At sites where surface remedial action is complete and at sites where remedial action has not yet begun, the environmental program consists primarily of surface water and ground water monitoring to support site characterization, baseline risk assessments, or disposal site performance assessments.

Not Available

1994-10-01T23:59:59.000Z

259

Dual superconductivity and vacuum properties in Yang--Mills theories  

E-Print Network [OSTI]

We address, within the dual superconductivity model for color confinement, the question whether the Yang-Mills vacuum behaves as a superconductor of type I or type II. In order to do that we compare, for the theory with gauge group SU(2), the determination of the field penetration depth $\\lambda$ with that of the superconductor correlation length $\\xi$. The latter is obtained by measuring the temporal correlator of a disorder parameter developed by the Pisa group to detect dual superconductivity. The comparison places the vacuum close to the border between type I and type II and marginally on the type II side. We also check our results against the study of directly measurable effects such as the interaction between two parallel flux tubes, obtaining consistent indications for a weak repulsive behaviour. Future strategies to improve our investigation are discussed.

A. D'Alessandro; M. D'Elia; L. Tagliacozzo

2007-05-03T23:59:59.000Z

260

Protect and Restore Mill Creek Watershed : Annual Report CY 2005.  

SciTech Connect (OSTI)

The Nez Perce Tribe Department of Fisheries Resource Management, Watershed Division approaches watershed restoration with a ridge-top to ridge-top approach. The Nez Perce Tribe and the Nez Perce National Forest (NPNF) have formed a partnership in completing watershed restoration activities, and through this partnership, more work is accomplished by sharing funding and resources in our effort. The Nez Perce Tribe began watershed restoration projects within the Mill Creek watershed of the South Fork Clearwater River in 2000. Progress has been made in restoring the watershed through excluding cattle from critical riparian areas through fencing. Starting in FY 2002, continuing into 2004, trees were planted in riparian areas in the meadow of the upper watershed. In addition, a complete inventory of culverts at road-stream crossings was completed. Culverts have been prioritized for replacement to accommodate fish passage throughout the watershed, and one high priority culvert was replaced in 2004. Maintenance to the previously built fence was also completed.

McRoberts, Heidi

2006-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Ultra-short pulse generator  

DOE Patents [OSTI]

An inexpensive pulse generating circuit is disclosed that generates ultra-short, 200 picosecond, and high voltage 100 kW, pulses suitable for wideband radar and other wideband applications. The circuit implements a nonlinear transmission line with series inductors and variable capacitors coupled to ground made from reverse biased diodes to sharpen and increase the amplitude of a high-voltage power MOSFET driver input pulse until it causes non-destructive transit time breakdown in a final avalanche shock wave diode, which increases and sharpens the pulse even more. 5 figures.

McEwan, T.E.

1993-12-28T23:59:59.000Z

262

Short-Term Energy Outlook  

Gasoline and Diesel Fuel Update (EIA)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelines About U.S. Natural GasquestionnairesquestionnairesGasA.San3 1 Short-Term Energy33

263

Short-Term Energy Outlook  

Gasoline and Diesel Fuel Update (EIA)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelines About U.S. Natural GasquestionnairesquestionnairesGasA.San3 1 Short-Term

264

Short-Term Energy Outlook  

Gasoline and Diesel Fuel Update (EIA)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelines About U.S. Natural GasquestionnairesquestionnairesGasA.San3 1 Short-Term(STEO)

265

Gasoline prices decrease (Short version)  

Gasoline and Diesel Fuel Update (EIA)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"Click worksheet9,1,50022,3,,,,6,1,,781 2,328 2,683DieselValues shown for(long24, 2014GasolineShort

266

Characterization of prealloyed copper powders treated in high energy ball mill  

SciTech Connect (OSTI)

The inert gas atomised prealloyed copper powders containing 3.5 wt.% Al were milled up to 20 h in the planetary ball mill in order to oxidize aluminium in situ with oxygen from the air. In the next procedure compacts from milled powder were synthesized by hot-pressing in argon atmosphere. Compacts from as-received Cu-3.5 wt.% Al powder and electrolytic copper powder were also prepared under the same conditions. Microstructural and morphological changes of high energy milled powder as well as changes of thermal stability and electrical conductivity of compacts were studied as a function of milling time and high temperature exposure at 800 deg. C. Optical, scanning electron microscopy (SEM) and X-ray diffraction analysis were performed for microstructural characterization, whereas thermal stability and electrical conductivity were evaluated by microhardness measurements and conductometer Sigmatest, respectively. The prealloyed 5 h-milled and compacted powder showed a significant increase in microhardness reaching the value of 2600 MPa, about 4 times greater than that of compacts synthesized from as-received electrolytic copper powder (670 MPa). The electrical conductivity of compacts from 5 h-milled powder was 52% IACS. The results were discussed in terms of the effect of small grain size and finely distributed alumina dispersoids on hardening and thermal stability of compacts.

Rajkovic, Viseslava [Institute of Nuclear Sciences 'Vinca', P.O. Box 522, 11001 Belgrade (Serbia and Montenegro)]. E-mail: visnja@vin.bg.ac.yu; Bozic, Dusan [Institute of Nuclear Sciences 'Vinca', P.O. Box 522, 11001 Belgrade (Serbia and Montenegro); Jovanovic, Milan T. [Institute of Nuclear Sciences 'Vinca', P.O. Box 522, 11001 Belgrade (Serbia and Montenegro)

2006-08-15T23:59:59.000Z

267

Petrochem industry expands North American MTBE capacity  

SciTech Connect (OSTI)

This paper reports that petrochemical manufacturers continue to increase methyl tertiary butyl ether (MTBE) capacity in North America. The action reflects refiners' reformulation of gasoline to help reduce auto emissions. Demand for gasoline blending oxygenates such as MTBE is expected to increase as U.S. refiners reconfigure processing trains to produce fuels meeting requirements of the Clean Air Act amendments of 1990. Recent progress includes plans to build an MTBE plant in Mexico and start-ups of plants on the U.S. Gulf Coast and in Canada.

Not Available

1992-10-05T23:59:59.000Z

268

Installed Geothermal Capacity | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place: Eden Prairie,InfieldInstalled Geothermal Capacity Jump to:

269

ISO New England Forward Capacity Market (Rhode Island)  

Broader source: Energy.gov [DOE]

Under the Forward Capacity Market (FCM), ISO New England projects the capacity needs of the region’s power system three years in advance and then holds an annual auction to purchase the power...

270

Storage and capacity rights markets in the natural gas industry  

E-Print Network [OSTI]

This dissertation presents a different approach at looking at market power in capacity rights markets that goes beyond the functional aspects of capacity rights markets as access to transportation services. In particular, ...

Paz-Galindo, Luis A.

1999-01-01T23:59:59.000Z

271

The economics of shutting and restarting primary aluminium smelting capacity  

SciTech Connect (OSTI)

In recent years the aluminum industry in the Western world has been operating well below capacity, with cutbacks in production due largely to the depressed aluminum market conditions of 1992 and 1993. Since mid-1995, however, aluminum producers have begun restarting idled capacity. Extensive efforts and preparation are required both to close capacity in an orderly manner and to restart idled capacity. This paper presents a comprehensive analysis of the costs of shutting capacity, maintaining idled capacity, and restarting potlines. Costs have been calculated for a smelter which may be considered representative of the industry as a whole. Technical aspects and commercial data are outlined for the representative smelter, with costs presented under a variety of shutdown and restart conditions. Additionally, the time required to bring capacity back on-line is examined for several scenarios, and the economic impact of idled capacity is discussed.

Driscoll, K.J. [CRU International, Ltd., London (United Kingdom)

1996-10-01T23:59:59.000Z

272

A reduction theorem for capacity of positive maps  

E-Print Network [OSTI]

We prove a reduction theorem for capacity of positive maps of finite dimensional C*-algebras, thus reducing the computation of capacity to the case when the image of a nonscalar projection is never a projection.

Erling Stormer

2005-10-06T23:59:59.000Z

273

Author's personal copy Ramp metering and freeway bottleneck capacity  

E-Print Network [OSTI]

; Hall and Agyemang-Duah, 1991; Banks, 1991a,b). The two-capacity hypothesis argues that metering can

Levinson, David M.

274

SHORT-TUBE SUBCRITICAL FLOW Enerag Division  

E-Print Network [OSTI]

#12;SHORT-TUBE SUBCRITICAL FLOW Y. C. Mei Enerag Division Oak Ridge National Laboratory Oak Ridge-tube subcritical flow. For short tubes used as refrigerant expansion devices, the orifice model is found inadequate-TUBE SUBCRITICAL FLOW INTRODUCTION Much theoretical and experimental work regarding short tube fluid flow has

Oak Ridge National Laboratory

275

Uranium Mill Tailings Remedial Action Project, Surface Project Management Plan. Revision 1  

SciTech Connect (OSTI)

Title I of the Uranium Mill Tailings Radiation Control Act (UMTRCA) authorizes the US Department of Energy (DOE) to undertake remedial action at 24 designated inactive uranium processing sites and associated vicinity properties (VP) containing uranium mill tailings and related residual radioactive materials. The purpose of the Uranium Mill Tailings Remedial Action (UMTRA) Surface Project is to minimize or eliminate radiation health hazards to the public and the environment at the 24 sites and related VPs. This document describes the management organization, system, and methods used to manage the design, construction, and other activities required to clean up the designated sites and associated VPs, in accordance with the UMTRCA.

Not Available

1994-12-01T23:59:59.000Z

276

Evaluation of in vitro dissolution rates of throum in uranium mill tailings  

SciTech Connect (OSTI)

Dissolution rates of thorium from the uranium mill tailings piles at two Department of Energy Uranium Mill Tailings Remedial Action Project (UMTRAP) sites have been evaluated. The thorium dissolution rates were evaluated in vitro using simulated lung fluid. The former uranium mills at the UMTRAP sites employed different chemical processes (acid leach and alkaline pressure leach) to extract the uranium from the ore, and the thorium dissolution rates at these sites were found to be markedly different. A site specific annual limit on intake (ALI) value for {sup 230}Th was calculated for the UMTRAP Site that was associated with a multiple component dissolution curve.

Reif, R.G. [Department of Energy, Albuquerque, NM (United States)

1996-06-01T23:59:59.000Z

277

Evaluation of in vitro dissolution rates of thorium in uranium mill tailings  

SciTech Connect (OSTI)

Dissolution rates of thorium from the uranium mill tailings piles at two Department of Energy Uranium Mill Tailings Remedial Action Project (UMTRAP) sites have been evaluated. The thorium dissolution rates were evaluated in vitro using simulated lung fluid. The former uranium mills at the UMTRAP sites employee different chemical processes (acid leach and alkaline pressure leach) to extract the uranium from the ore, and the thorium dissolution rates at these sites were found to be markedly different. A site specific annual limit on intake (ALI) value for {sup 230}Th was calculated for the UMTRAP site that was associated with a multiple component dissolution curve. 9 refs., 1 fig., 3 tabs.

Reif, R.H. [RUST Federal Services, Albuquerque, NM (United States)

1994-11-01T23:59:59.000Z

278

Decommissioning and waste disposal methods for an uranium mill facility in Spain  

SciTech Connect (OSTI)

In the south of Spain on the outskirts of the town of Andujar an inactive uranium mill tailings pile is being stabilized in place. Mill equipment, buildings and process facilities have been dismantled and demolished and the resulting metal wastes and debris will be placed in the pile. The tailings mass is being reshaped by flattening the sideslopes and a cover system will be placed over the pile. This paper describes the technical procedures used for the remediation and closure of the Andujar mill site and in particular discusses the approaches used for the dismantling and demolition of the processing facilities and the disposal of the metal wastes and demolition debris.

Santiago, J.L. [ENRESA, Madrid (Spain); Sanchez, M. [INITEC, Madrid (Spain)

1993-12-31T23:59:59.000Z

279

Titania Prepared by Ball Milling: Its Characterization and Application as Liquefied Petroleum Gas Sensor  

E-Print Network [OSTI]

Present paper reports the LPG sensing of TiO2 obtained through ball milling. The milled powder was characterized by XRD, TEM and UV-visible spectroscopy. Further the ball milled powder was compressed in to pellet using hydraulic press. This pellet was investigated with the exposure of LPG. Variations in resistance with exposure of LPG to the sensing pellet were recorded. The sensitivity of the sensor was ~ 11 for 5 vol.% of LPG. Response and recovery times of the sensor were ~ 100 and 250 sec. The sensor was quite sensitive to LPG and results were found reproducible within 91%.

Yadav, B C; Singh, Satyendra; Yadav, T P

2012-01-01T23:59:59.000Z

280

Theory of Molecular Machines. I. Channel Capacity of Molecular Machines  

E-Print Network [OSTI]

Theory of Molecular Machines. I. Channel Capacity of Molecular Machines running title: Channel Capacity of Molecular Machines Thomas D. Schneider version = 5.76 of ccmm.tex 2004 Feb 3 Version 5.67 was submitted 1990 December 5 Schneider, T. D. (1991). Theory of molecular machines. I. Channel capacity

Schneider, Thomas D.

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Competitive Acquisition of Prioritizable Capacity-Based Ancillary Services  

E-Print Network [OSTI]

the competitive procurement of capacity-based ancillary services (AS) in unbundled markets by the Independent Grid1 Competitive Acquisition of Prioritizable Capacity-Based Ancillary Services Gianfranco Chicco Operator (IGO). The capacity-based AS are prioritized in order of ascending response times. Prioritization

282

TOWARDS REACHING CONSENSUS IN THE DETERMINATION OF PHOTOVOLTAICS CAPACITY CREDIT  

E-Print Network [OSTI]

, 251 Fuller Rd Albany, NY, 12203 Perez@asrc.cestm.albany,edu Mike Taylor Solar Electric Power effort to reach consensus on the notion of capacity credit for solar power electrical generation capacity or capacity credit of a power plant quantifies the output of a power plant that effectively

Perez, Richard R.

283

Information storage capacity of discrete spin systems  

SciTech Connect (OSTI)

Understanding the limits imposed on information storage capacity of physical systems is a problem of fundamental and practical importance which bridges physics and information science. There is a well-known upper bound on the amount of information that can be stored reliably in a given volume of discrete spin systems which are supported by gapped local Hamiltonians. However, all the previously known systems were far below this theoretical bound, and it remained open whether there exists a gapped spin system that saturates this bound. Here, we present a construction of spin systems which saturate this theoretical limit asymptotically by borrowing an idea from fractal properties arising in the Sierpinski triangle. Our construction provides not only the best classical error-correcting code which is physically realizable as the energy ground space of gapped frustration-free Hamiltonians, but also a new research avenue for correlated spin phases with fractal spin configurations. -- Highlights: •We propose a spin model with fractal ground states and study its coding properties. •We show that the model asymptotically saturates a theoretical limit on information storage capacity. •We discuss its relations to various theoretical physics problems.

Yoshida, Beni, E-mail: rouge@caltech.edu

2013-11-15T23:59:59.000Z

284

Multi-region capacity planning model with contracts of varying duration under uncertainty : a satellite capacity acquisition case study  

E-Print Network [OSTI]

This paper highlights the issues associated with and presents a modeling framework for long-term capacity planning problems constrained in a similar fashion to satellite capacity acquisition. Although ambiguities exist, ...

Lydiard, John M., IV

2014-01-01T23:59:59.000Z

285

Complex Hydride Compounds with Enhanced Hydrogen Storage Capacity  

SciTech Connect (OSTI)

The United Technologies Research Center (UTRC), in collaboration with major partners Albemarle Corporation (Albemarle) and the Savannah River National Laboratory (SRNL), conducted research to discover new hydride materials for the storage of hydrogen having on-board reversibility and a target gravimetric capacity of ? 7.5 weight percent (wt %). When integrated into a system with a reasonable efficiency of 60% (mass of hydride / total mass), this target material would produce a system gravimetric capacity of ? 4.5 wt %, consistent with the DOE 2007 target. The approach established for the project combined first principles modeling (FPM - UTRC) with multiple synthesis methods: Solid State Processing (SSP - UTRC), Solution Based Processing (SBP - Albemarle) and Molten State Processing (MSP - SRNL). In the search for novel compounds, each of these methods has advantages and disadvantages; by combining them, the potential for success was increased. During the project, UTRC refined its FPM framework which includes ground state (0 Kelvin) structural determinations, elevated temperature thermodynamic predictions and thermodynamic / phase diagram calculations. This modeling was used both to precede synthesis in a virtual search for new compounds and after initial synthesis to examine reaction details and options for modifications including co-reactant additions. The SSP synthesis method involved high energy ball milling which was simple, efficient for small batches and has proven effective for other storage material compositions. The SBP method produced very homogeneous chemical reactions, some of which cannot be performed via solid state routes, and would be the preferred approach for large scale production. The MSP technique is similar to the SSP method, but involves higher temperature and hydrogen pressure conditions to achieve greater species mobility. During the initial phases of the project, the focus was on higher order alanate complexes in the phase space between alkaline metal hydrides (AmH), Alkaline earth metal hydrides (AeH2), alane (AlH3), transition metal (Tm) hydrides (TmHz, where z=1-3) and molecular hydrogen (H2). The effort started first with variations of known alanates and subsequently extended the search to unknown compounds. In this stage, the FPM techniques were developed and validated on known alanate materials such as NaAlH4 and Na2LiAlH6. The coupled predictive methodologies were used to survey over 200 proposed phases in six quaternary spaces, formed from various combinations of Na, Li Mg and/or Ti with Al and H. A wide range of alanate compounds was examined using SSP having additions of Ti, Cr, Co, Ni and Fe. A number of compositions and reaction paths were identified having H weight fractions up to 5.6 wt %, but none meeting the 7.5 wt%H reversible goal. Similarly, MSP of alanates produced a number of interesting compounds and general conclusions regarding reaction behavior of mixtures during processing, but no alanate based candidates meeting the 7.5 wt% goal. A novel alanate, LiMg(AlH4)3, was synthesized using SBP that demonstrated a 7.0 wt% capacity with a desorption temperature of 150°C. The deuteride form was synthesized and characterized by the Institute for Energy (IFE) in Norway to determine its crystalline structure for related FPM studies. However, the reaction exhibited exothermicity and therefore was not reversible under acceptable hydrogen gas pressures for on-board recharging. After the extensive studies of alanates, the material class of emphasis was shifted to borohydrides. Through SBP, several ligand-stabilized Mg(BH4)2 complexes were synthesized. The Mg(BH4)2*2NH3 complex was found to change behavior with slightly different synthesis conditions and/or aging. One of the two mechanisms was an amine-borane (NH3BH3) like dissociation reaction which released up to 16 wt %H and more conservatively 9 wt%H when not including H2 released from the NH3. From FPM, the stability of the Mg(BH4)2*2NH3 compound was found to increase with the inclusion of NH3 groups in the inner-Mg coordination

Mosher, Daniel A.; Opalka, Susanne M.; Tang, Xia; Laube, Bruce L.; Brown, Ronald J.; Vanderspurt, Thomas H.; Arsenault, Sarah; Wu, Robert; Strickler, Jamie; Anton, Donald L.; Zidan, Ragaiy; Berseth, Polly

2008-02-18T23:59:59.000Z

286

Long vs. short-term energy storage:sensitivity analysis.  

SciTech Connect (OSTI)

This report extends earlier work to characterize long-duration and short-duration energy storage technologies, primarily on the basis of life-cycle cost, and to investigate sensitivities to various input assumptions. Another technology--asymmetric lead-carbon capacitors--has also been added. Energy storage technologies are examined for three application categories--bulk energy storage, distributed generation, and power quality--with significant variations in discharge time and storage capacity. Sensitivity analyses include cost of electricity and natural gas, and system life, which impacts replacement costs and capital carrying charges. Results are presented in terms of annual cost, $/kW-yr. A major variable affecting system cost is hours of storage available for discharge.

Schoenung, Susan M. (Longitude 122 West, Inc., Menlo Park, CA); Hassenzahl, William V. (,Advanced Energy Analysis, Piedmont, CA)

2007-07-01T23:59:59.000Z

287

Drop short control of electrode gap  

DOE Patents [OSTI]

During vacuum consumable arc remelting the electrode gap between a consumable electrode and a pool of molten metal is difficult to control. The present invention monitors drop shorts by detecting a decrease in the voltage between the consumable electrode and molten pool. The drop shorts and their associated voltage reductions occur as repetitive pulses which are closely correlated to the electrode gap. Thus, the method and apparatus of the present invention controls electrode gap based upon drop shorts detected from the monitored anode-cathode voltage. The number of drop shorts are accumulated, and each time the number of drop shorts reach a predetermined number, the average period between drop shorts is calculated from this predetermined number and the time in which this number is accumulated. This average drop short period is used in a drop short period electrode gap model which determines the actual electrode gap from the drop short. The actual electrode gap is then compared with a desired electrode gap which is selected to produce optimum operating conditions and the velocity of the consumable error is varied based upon the gap error. The consumable electrode is driven according to any prior art system at this velocity. In the preferred embodiment, a microprocessor system is utilized to perform the necessary calculations and further to monitor the duration of each drop short. If any drop short exceeds a preset duration period, the consumable electrode is rapidly retracted a predetermined distance to prevent bonding of the consumable electrode to the molten remelt.

Fisher, Robert W. (Albuquerque, NM); Maroone, James P. (Albuquerque, NM); Tipping, Donald W. (Albuquerque, NM); Zanner, Frank J. (Sandia Park, NM)

1986-01-01T23:59:59.000Z

288

Atmospheric Crude Oil Distillation Operable Capacity  

Gasoline and Diesel Fuel Update (EIA)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"Click worksheet9,1,50022,3,,,,6,1,,781Title: Telephone:shortOil and Natural8U.S.NA (Barrels per Calendar

289

INVESTING IN NEW BASE LOAD GENERATING CAPACITY  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelines AboutDecember 2005 (Thousand9,0, 1997Environment >7,992000 Short-TermSeptember»I L

290

Leica-Inverted-2 -1-Short instructions Short instructions for the Leica-Inverted-2  

E-Print Network [OSTI]

Leica-Inverted-2 -1- Short instructions Short instructions for the Leica-Inverted-2 Version 230307 off the system Page 8 8. Trouble shooting Page 10 #12;Leica-Inverted-2 -2- Short instructions 1. Laser;Leica-Inverted-2 -3- Short instructions 2. General guidelines 1. Lab rules: This room is a S2 laboratory

Manstein, Dietmar J.

291

Rogue waves for a long wave-short wave resonance model with multiple short waves  

E-Print Network [OSTI]

1 Rogue waves for a long wave-short wave resonance model with multiple short waves Hiu Ning Chan (1 waves; Long-short resonance PACS Classification: 02.30.Jr; 05.45.Yv; 47.35.Fg #12;2 ABSTRACT A resonance between long and short waves will occur if the phase velocity of the long wave matches the group velocity

292

Conformally flat Einstein-Yang-Mills-Higgs solutions with spherical symmetry  

SciTech Connect (OSTI)

We solve the Einstein-Yang-Mills-Higgs equations in a conformally flat metric with spherical symmetry. Two solutions are obtained corresponding to magnetic monopoles in the Higgs vacuum and outside of it.

Mondaini, R.P.; Santos, N.O.

1983-10-15T23:59:59.000Z

293

Regulatory impact analysis of environmental standards for uranium mill tailings at active sites. Final report  

SciTech Connect (OSTI)

The Environmental Protection Agency was directed by Congress, under PL 95-604, the Uranium Mill Tailings Radiation Control Act of 1978, to set standards of general application that provide protection from the hazards associated with uranium mill tailings. Title I of the Act pertains to tailings at inactive sites for which the Agency has developed standards as part of a separate rulemaking. Title II of the Act requires standards covering the processing and disposal of byproduct materials at mills which are currently licensed by the appropriate regulatory authorities. This Regulatory Impact Analysis (RIA) addresses the standards developed under Title II. There are two major parts of the standards for active mills: standards for control of releases from tailings during processing operations and prior to final disposal, and standards for protection of the public after the disposal of tailings. This report presents a detailed analysis of standards for disposal only, since the analysis required for the operations standards is very limited.

Not Available

1983-03-01T23:59:59.000Z

294

Bioremediation of ground water contaminants at a uranium mill tailings site  

SciTech Connect (OSTI)

Ground water contaminated with uranium from milling operations must be remediated to reduce the migration of soluble toxic compounds. At the mill tailings site near Tuba City, Arizona (USA) the approach is to employ bioremediation for in situ immobilization of uranium by bacterial reduction of uranyl, U(VI), compounds to uraninite, U(IV). In this initial phase of remediation, details are provided to indicate the magnitude of the contamination problem and to present preliminary evidence supporting the proposition that bacterial immobilization of uranium is possible. Additionally, consideration is given to contaminating cations and anions that may be at toxic levels in ground water at this uranium mill tailing site and detoxification strategies using bacteria are addressed. A model concept is employed so that results obtained at the Tuba City site could contribute to bioremediation of ground water at other uranium mill tailings sites.

Barton, L.L.; Nuttall, H.E.; Thomson, B.M.; Lutze, W. [Univ. of New Mexico, Albuquerque, NM (United States)

1995-12-31T23:59:59.000Z

295

EA-1155: Ground-water Compliance Activities at the Uranium Mill Tailings Site, Spook, Wyoming  

Broader source: Energy.gov [DOE]

This EA evaluates the environmental impacts for the proposal to comply with the Environmental Protection Agency's ground-water standards set forth in 40 CFR 192 at the Spook, Wyoming Uranium Mill...

296

Radiation of a circulating quark in strongly coupled N = 4 super Yang-Mills theory  

E-Print Network [OSTI]

The energy density and angular distribution of power radiated by a quark undergoing circular motion in strongly coupled N? = ?4 supersymmetric Yang?Mills (SYM) theory is computed using gauge?gravity duality. The results ...

Athanasiou, Christiana

297

Case Study of Optimal Byproduct Gas Distribution in Integrated Steel Mill Using Multi-Period Optimization  

E-Print Network [OSTI]

? ? ? Case Study of Optimal Byproduct Gas Distribution in Integrated Steel Mill Using Multi-Period Optimization KIMMO M?KINEN BUSINESS MANAGER TONI KYM?L?INEN PRODUCT MANAGER JAAKKO JUNTTILA SALES MANAGER ABB OY HELSINKI FINLAND...

Makinen, K.; Kymalainen, T.; Junttila, J.

2012-01-01T23:59:59.000Z

298

Optimal handling of Highly Active Pharmaceutical Ingredients during milling and blending operations  

E-Print Network [OSTI]

This thesis investigates best practices for Highly Active Pharmaceutical Ingredient (HAPI) milling and blending. We utilize a qualitative analysis centering on a benchmarking study and quantitative analyses using a ...

Setty, Prashant (Prashant Neelappanavara)

2013-01-01T23:59:59.000Z

299

Moab Uranium Mill Tailings Cleanup Project Steps into Spotlight at International Meeting in Vienna  

Broader source: Energy.gov [DOE]

VIENNA – The Moab Uranium Mill Tailings Remedial Action (UMTRA) Project has kept the United States at the forefront of characterization, remediation, and end-state reuse of uranium millsites around the world.

300

Energy Efficiency Improvements and Cost Saving Opportunities in the Corn Wet Milling Industry  

E-Print Network [OSTI]

Corn wet milling is the most energy intensive industry in the food and kindred products group (SIC 20). Plants typically spend approximately $15 to 25 million per year on energy, one of its largest operating costs, making energy efficiency...

Galitsky, C.; Worrell, E.

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

The FreeD - A Handheld Digital Milling Device for Craft and Fabrication  

E-Print Network [OSTI]

We present an approach to combine digital fabrication and craft that is focused on a new fabrication experience. The FreeD is a hand-held, digitally controlled, milling device. It is guided and monitored by a computer while ...

Paradiso, Joseph

302

Moab Project Disposes 2 Million Tons of Uranium Mill Tailings with Recovery Act Funds  

Broader source: Energy.gov [DOE]

The Moab Uranium Mill Tailings Remedial Action Project reached its primary American Recovery and Reinvestment Act milestone ahead of schedule on Wednesday with the disposal of 2 million tons of...

303

Adsorption -capacity data for 283 organic compounds  

SciTech Connect (OSTI)

Adsorption on activated carbon is a widely used method for removing volatile organic compounds (VOCs) from gases and other exhaust streams. This article presents a compilation of adsorption-capacity data as a function of the VOC concentration in the gas. The results are useful in engineering and environmental studies, and in the design of carbon-based adsorption systems to remove unwanted organic pollutants from gases. For vapor control, carbon-based systems typically combine a carbon-adsorption unit with a secondary control method to reclaim or destroy the vapors desorbed during carbon-bed regeneration. To remove organics dissolved in wastewater, air stripping is typically used to transfer the organics to a vapor stream. Carbon adsorption is then used to separate the organics from the stripper exhaust. Collected vapors can be recovered for reuse or destroyed, depending on their value.

Yaws, C.L.; Bu, L.; Nijhawan, S. [Lamar Univ., Beaumont, TX (United States)

1995-05-01T23:59:59.000Z

304

Korean oxygenates rule sparks MTBE capacity plans  

SciTech Connect (OSTI)

The Korean government`s strict standard for gasoline sold domestically is expected to have a significant impact on the methyl tert-butyl ether (MTBE) market. The mandate-requiring gasoline oxygen content of 0.5% this year, 0.75% by 1996, and 1.0% by 1998-has sparked a rush by Korean refineries to build new MTBE plants. If expansion plans are carried out, Korea`s MTBE capacity will increase from 280,000 m.t./year to 650,000 m.t./year by 1996, far surpassing predicted demand. Honam Oil, part of the Lucky Group, plans startup of a 100,000-m.t./year unit at Yeochon by early 1996. In addition, by the end of 1996 Ssangyong Oil will bring a 100,000-m.t./year unit onstream.

Kim, Hyung-Jin

1994-06-15T23:59:59.000Z

305

The NASA CSTI High Capacity Power Program  

SciTech Connect (OSTI)

The SP-100 program was established in 1983 by DOD, DOE, and NASA as a joint program to develop the technology necessary for space nuclear power systems for military and civil applications. During 1986 and 1987, the NASA Advanced Technology Program was responsible for maintaining the momentum of promising technology advancement efforts started during Phase I of SP-100 and to strengthen, in key areas, the chances for successful development and growth capability of space nuclear reactor power systems for future space applications. In 1988, the NASA Advanced Technology Program was incorporated into NASA`s new Civil Space Technology Initiative (CSTI). The CSTI program was established to provide the foundation for technology development in automation and robotics, information, propulsion, and power. The CSTI High Capacity Power Program builds on the technology efforts of the SP-100 program, incorporates the previous NASA advanced technology project, and provides a bridge to the NASA exploration technology programs. The elements of CSTI high capacity power development include conversion systems - Stirling and thermoelectric, thermal management, power management, system diagnostics, and environmental interactions. Technology advancement in all areas, including materials, is required to provide the growth capability, high reliability and 7 to 10 years lifetime demanded for future space nuclear power systems. The overall program will develop and demonstrate the technology base required to provide a wide range of modular power systems while minimizing the impact of day/night operation as well as attitudes and distance from the Sun. Significant accomplishments in all of the program elements will be discussed, along with revised goals and project timelines recently developed.

Winter, J.M.

1994-09-01T23:59:59.000Z

306

XAFS of Synthetic Iron(III)-Arsenate Co-Precipitates and Uranium Mill Neutralized Raffinate  

SciTech Connect (OSTI)

XAFS studies were carried out for chemical speciation of arsenic species in uranium mill neutralized raffinate solids. To aid the structural characterization, synthetic iron(III)-arsenate co-precipitates were prepared to mimic the actual uranium mill tailings neutralization products. The principle components analysis method was used to validate the synthetic amorphous scorodite as a primary model compound for arsenate species in the raffinate samples under the specific precipitation conditions.

Chen, N. [Canadian Light Source, University of Saskatchewan, Saskatoon, SK S7N 0X4 (Canada); Department of Geological Sciences, University of Saskatchewan, Saskatoon, SK (Canada); Jiang, D. T. [Canadian Light Source, University of Saskatchewan, Saskatoon, SK S7N 0X4 (Canada); COGEMA Resources Inc., Saskatoon, SK S7K 3X5 (Canada); Department of Physics, University of Guelph, Guelph, ON N1G 2W1 (Canada); Cutler, J. [Canadian Light Source, University of Saskatchewan, Saskatoon, SK S7N 0X4 (Canada); Demopoulos, G. P. [Department of Geological Sciences, University of Saskatchewan, Saskatoon, SK (Canada); Rowson, J. W. [Department of Materials Engineering, McGill University, Montreal, QC H3A 2B2 (Canada)

2007-02-02T23:59:59.000Z

307

Accepting Mixed Waste as Alternate Feed Material for Processing and Disposal at a Licensed Uranium Mill  

SciTech Connect (OSTI)

Certain categories of mixed wastes that contain recoverable amounts of natural uranium can be processed for the recovery of valuable uranium, alone or together with other metals, at licensed uranium mills, and the resulting tailings permanently disposed of as 11e.(2) byproduct material in the mill's tailings impoundment, as an alternative to treatment and/or direct disposal at a mixed waste disposal facility. This paper discusses the regulatory background applicable to hazardous wastes, mixed wastes and uranium mills and, in particular, NRC's Alternate Feed Guidance under which alternate feed materials that contain certain types of mixed wastes may be processed and disposed of at uranium mills. The paper discusses the way in which the Alternate Feed Guidance has been interpreted in the past with respect to processing mixed wastes and the significance of recent changes in NRC's interpretation of the Alternate Feed Guidance that sets the stage for a broader range of mixed waste materials to be processed as alternate feed materials. The paper also reviews the le gal rationale and policy reasons why materials that would otherwise have to be treated and/or disposed of as mixed waste, at a mixed waste disposal facility, are exempt from RCRA when reprocessed as alternate feed material at a uranium mill and become subject to the sole jurisdiction of NRC, and some of the reasons why processing mixed wastes as alternate feed materials at uranium mills is preferable to direct disposal. Finally, the paper concludes with a discussion of the specific acceptance, characterization and certification requirements applicable to alternate feed materials and mixed wastes at International Uranium (USA) Corporation's White Mesa Mill, which has been the most active uranium mill in the processing of alternate feed materials under the Alternate Feed Guidance.

Frydenland, D. C.; Hochstein, R. F.; Thompson, A. J.

2002-02-26T23:59:59.000Z

308

Water-cooled ion-milled diffraction gratings for the synchrotron radiation community  

SciTech Connect (OSTI)

Key technical and strategic choices are reviewed, leading to the fabrication method of ion-milled grating grooves for the monochromators at the Advanced Light Source (ALS) at Lawrence Berkeley Laboratory (LBL), and for other synchrotrons. Several laboratories and their industrial partners have joined to manufacture gratings with essentially theoretical performance. Metrology -data and theoretical comparisons are given for square wave profile grating samples ion-milled into electroless nickel surfaces. The extensive capabilities of Hughes Aircraft in grating manufacture are reviewed.

McKinney, W.R.; Shannon, C.L.; Shults, E.N.

1993-08-01T23:59:59.000Z

309

Static Cosmological Solutions of the Einstein-Yang-Mills-Higgs Equations  

E-Print Network [OSTI]

Numerical evidence is presented for the existence of a new family of static, globally regular `cosmological' solutions of the spherically symmetric Einstein-Yang-Mills-Higgs equations. These solutions are characterized by two natural numbers ($m\\geq 1$, $n\\geq 0$), the number of nodes of the Yang-Mills and Higgs field respectively. The corresponding spacetimes are static with spatially compact sections with 3-sphere topology.

P. Breitenlohner; P. Forgács; D. Maison

2000-06-13T23:59:59.000Z

310

Effect of high temperature on fruit set of selected genotypes of Lycopersicon esculentum mill.  

E-Print Network [OSTI]

EFFECT OF HIGH TEMPERATURE ON FRUIT SET OF SELECTED GENOTYPES OF LYCOPERSICON ESCULENTUM MILL. A Thesis by ROBERT KEVAN BARRINGER Submitted to the Graduate College of Texas A&M University in partial fullfillment of the requirements... for the degree of MASTER OF SCIENCE December 1982 Major Subject: Horticulture EFFECT OF HIGH TEMPERATURE ON FRUIT SET OF SELECTED GENOTYPES OF LYCOPERSICON ESCULENTUM MILL. A Thes(s by ROBERT KEVAN BARRINGER Approved as to style and content by: Chalrma...

Barringer, Robert Kevan

1982-01-01T23:59:59.000Z

311

Uranium Mill Tailings Remedial Action fiscal year 1992 roadmap  

SciTech Connect (OSTI)

The Uranium Mill Tailings Remedial Action (UMTRA) Project is funded and managed as two separate projects: Surface remediation (UMTRA-S) and Groundwater compliance (UMTRA-G). Surface remediation is a Major System Acquisition and has been completed at 10 sites, 7 sites are under construction, and 7 sites are in the planning stage. The planning stages of the UMTRA-G Project, a major project, began in April 1991. A programmatic environmental impact statement (PEIS) has been started. Site characterization work and baseline risk assessment will begin FY 1993. Thus, the UMTRA-S Project is a mature and ongoing program with the roles of various organizations well defined, while the UMTRA-G Project is still being formulated and the interfaces between the DOE, states and tribes, and the EPA are being established. The Office of Environmental Restoration and Waste Management (EM) directed that all projects under its authority develop roadmaps for their activities. The UMTRA Project Roadmap was developed by the UMTRA Project Office with input from the TAC, RAC, the GJPO, and assistance from SAIC. A single roadmap has been prepared for both the UMTRA-S and UMTRA-G Projects. This was deemed appropriate due to the close relationship between the projects and to the fact that the same Government and contractor personnel are preparing the roadmaps. Roadmap development is a planning process that focuses on issue identification, root-cause analysis, and issues resolution. The methodology is divided into three phases: assessment, analysis, and issues resolution.

Not Available

1993-02-01T23:59:59.000Z

312

Uranium Mill Tailings Remedial Action Project 1994 environmental report  

SciTech Connect (OSTI)

This annual report documents the Uranium Mill Tailings Remedial Action (UMTRA) Project environmental monitoring and protection program. The UMTRA Project routinely monitors radiation, radioactive residual materials, and hazardous constituents at associated former uranium tailings processing sites and disposal sites. At the end of 1994, surface remedial action was complete at 14 of the 24 designated UMTRA Project processing sites: Canonsburg, Pennsylvania; Durango, Colorado; Grand Junction, Colorado; Green River Utah, Lakeview, Oregon; Lowman, Idaho; Mexican Hat, Utah; Riverton, Wyoming; Salt Lake City, Utah; Falls City, Texas; Shiprock, New Mexico; Spook, Wyoming, Tuba City, Arizona; and Monument Valley, Arizona. Surface remedial action was ongoing at 5 sites: Ambrosia Lake, New Mexico; Naturita, Colorado; Gunnison, Colorado; and Rifle, Colorado (2 sites). Remedial action has not begun at the 5 remaining UMTRA Project sites that are in the planning stage. Belfield and Bowman, North Dakota; Maybell, Colorado; and Slick Rock, Colorado (2 sites). The ground water compliance phase of the UMTRA Project started in 1991. Because the UMTRA Project sites are.` different stages of remedial action, the breadth of the UMTRA environmental protection program differs from site to site. In general, sites actively undergoing surface remedial action have the most comprehensive environmental programs for sampling media. At sites where surface remedial action is complete and at sites where remedial action has not yet begun, the environmental program consists primarily of surface water and ground water monitoring to support site characterization, baseline risk assessments, or disposal site performance assessments.

NONE

1995-08-01T23:59:59.000Z

313

E-Print Network 3.0 - affecting energy capacity Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

reserves provided by the block with capacity... , which, in turn, impacts the capacity markets, be they energy or ancillary services markets, is adequacy... capacity ofsellers'...

314

Environmental analysis and data report prepared for the environmental assessment of remedial action at the Lowman uranium mill tailings site near Lowman, Idaho. [Urnanium Mill Tailings Remedial Action (UMTRA) Project  

SciTech Connect (OSTI)

This document contains information and data gathered in support of the preparation of the environmental assessment (EA) of the proposed remedial action at the Uranium Mill Tailings Remedial Action (UMTRA) Project site near Lowman, Idaho. The Lowman EA was prepared pursuant to the National Environmental Policy Act (NEPA), which requires Federal agencies to assess the effects of their actions on the environment. It examines the short-term and the long-term effects of the US Department of Energy's (DOE) proposed remedial action for the Lowman site as well as the no action alternative. The DOE will use the information and analyses presented in the EA to determine whether the proposed action would have a significant impact on the environment. If the impacts are determined to be significant, an environmental impact statement will be prepared. If the impacts are not judged to be significant, the DOE may issue a Finding of No Significant Impact and implement the proposed action. The information and data presented in this environmental analyses and data report are for background purposes only and are not required as part of the NEPA decision-making process.

Not Available

1991-01-01T23:59:59.000Z

315

Surface and bulk modified high capacity layered oxide cathodes with low irreversible capacity loss  

DOE Patents [OSTI]

The present invention includes compositions, surface and bulk modifications, and methods of making of (1-x)Li[Li.sub.1/3Mn.sub.2/3]O.sub.2.xLi[Mn.sub.0.5-yNi.sub.0.5-yCo.sub.2- y]O.sub.2 cathode materials having an O3 crystal structure with a x value between 0 and 1 and y value between 0 and 0.5, reducing the irreversible capacity loss in the first cycle by surface modification with oxides and bulk modification with cationic and anionic substitutions, and increasing the reversible capacity to close to the theoretical value of insertion/extraction of one lithium per transition metal ion (250-300 mAh/g).

Manthiram, Arumugam (Austin, TX); Wu, Yan (Austin, TX)

2010-03-16T23:59:59.000Z

316

Short-Rotation Woody Biomass Sustainability  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Review Short-Rotation Woody Biomass Sustainability Natalie A. Griffiths, Oak Ridge National Laboratory C. Rhett Jackson, University of Georgia Kellie Vache, Oregon State University...

317

SHORT COMMUNICATION: LARGER CLIQUES FOR A DIMACS ...  

E-Print Network [OSTI]

SHORT COMMUNICATION: LARGER CLIQUES FOR A. DIMACS TEST. A. GROSSO, M. LOCATELLI, W. J. PULLAN. 1. The new cliques. DIMACS benchmarks ...

318

Short-Term Energy Outlook September 2013  

U.S. Energy Information Administration (EIA) Indexed Site

September 2013 1 September 2013 Short-Term Energy Outlook (STEO) Highlights Monthly average crude oil prices increased for the fourth consecutive month in August 2013, as...

319

Modulation compression for short wavelength harmonic generation  

E-Print Network [OSTI]

Wavelength Harmonic Generation Ji Qiang Lawrence Berkeleyform a basis for fourth generation light source. Currently,e?ciency was proposed for generation of short wavelength

Qiang, J.

2010-01-01T23:59:59.000Z

320

Remedial action plan and site design for stabilization of the inactive uranium mill tailings site at Tuba City, Arizona: Phase 2, Construction, Subcontract documents: Appendix E, final report. [Uranium Mill Tailings Remedial Action (UMTRA) Project  

SciTech Connect (OSTI)

This appendix discusses Phase II construction and subcontract documents uranium mill site near Tuba City, Arizona. It contains the bid schedule, special conditions, specifications, and subcontract drawings.

Not Available

1989-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

The NASA CSTI High Capacity Power Project  

SciTech Connect (OSTI)

The SP-100 Space Nuclear Power Program was established in 1983 by DOD, DOE, and NASA as a joint program to develop technology for military and civil applications. Starting in 1986, NASA has funded a technology program to maintain the momentum of promising aerospace technology advancement started during Phase I of SP-100 and to strengthen, in key areas, the changes for successful development and growth capability of space nuclear reactor power systems for a wide range of future space applications. The elements of the CSTI High Capacity Power Project include Systems Analysis, Stirling Power Conversion, Thermoelectric Power Conversion, Thermal Management, Power Management, Systems Diagnostics, Environmental Interactions, and Material/Structural Development. Technology advancement in all elements is required to provide the growth capability, high reliability and 7 to 10 year lifetime demanded for future space nuclear power systems. The overall project with develop and demonstrate the technology base required to provide a wide range of modular power systems compatible with the SP-100 reactor which facilitates operation during lunar and planetary day/night cycles as well as allowing spacecraft operation at any attitude or distance from the sun. Significant accomplishments in all of the project elements will be presented, along with revised goals and project timelines recently developed.

Winter, J.; Dudenhoefer, J.; Juhasz, A.; Schwarze, G.; Patterson, R.; Ferguson, D.; Titran, R. [National Aeronautics and Space Administration, Cleveland, OH (United States). Lewis Research Center; Schmitz, P. [Sverdrup Technology, Inc., Brook Park, OH (United States). Lewis Research Center Group; Vandersande, J. [Jet Propulsion Lab., Pasadena, CA (United States)

1994-09-01T23:59:59.000Z

322

Refiners boost crude capacity; Petrochemical production up  

SciTech Connect (OSTI)

Continuing demand strength in refined products and petrochemical markets caused refiners to boost crude-charging capacity slightly again last year, and petrochemical producers to increase production worldwide. Product demand strength is, in large part, due to stable product prices resulting from a stabilization of crude oil prices. Crude prices strengthened somewhat in 1987. That, coupled with fierce product competition, unfortunately drove refining margins negative in many regions of the U.S. during the last half of 1987. But with continued strong demand for gasoline, and an increased demand for higher octane gasoline, margins could turn positive by 1989 and remain so for a few years. U.S. refiners also had to have facilities in place to meet the final requirements of the U.S. Environmental Protection Agency's lead phase-down rules on Jan. 1, 1988. In petrochemicals, plastics demand dept basic petrochemical plants at good utilization levels worldwide. U.S. production of basics such as ethylene and propylene showed solid increases. Many of the derivatives of the basic petrochemical products also showed good production gains. Increased petrochemical production and high plant utilization rates didn't spur plant construction projects, however. Worldwide petrochemical plant projects declined slightly from 1986 figures.

Corbett, R.A.

1988-03-21T23:59:59.000Z

323

North American Short Line and Regional Railroads Industry Report  

Broader source: Energy.gov (indexed) [DOE]

45G Short Line Tax Credit 45G Short Line Tax Credit government owned short lines government owned short lines State grants State grants D.O.E. investment D.O.E. investment...

324

Bangladesh-Enhancing Capacity for Low Emission Development Strategies...  

Open Energy Info (EERE)

Bangladesh-Enhancing Capacity for Low Emission Development Strategies (EC-LEDS) AgencyCompany Organization United States Agency for International Development, United States...

325

Thailand-Enhancing Capacity for Low Emission Development Strategies...  

Open Energy Info (EERE)

Enhancing Capacity for Low Emission Development Strategies (EC-LEDS) AgencyCompany Organization United States Agency for International Development, United States Environmental...

326

Design and Evaluation of Novel High Capacity Cathode Materials...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

49thackeray2011o.pdf More Documents & Publications Cathodes Design and Evaluation of Novel High Capacity Cathode Materials Stabilization of Layered Metal Oxides...

327

Design and Evaluation of Novel High Capacity Cathode Materials  

Broader source: Energy.gov (indexed) [DOE]

Design and Evaluation of Novel High Capacity Cathode Materials Christopher Johnson and Michael Thackeray Chemical Sciences and Engineering Division, Argonne Annual Merit Review DOE...

328

Philippines-Strengthening Planning Capacity for Low Carbon Growth...  

Open Energy Info (EERE)

building capacity based on research focusing on economic aspects, and raising public awareness about climate change challenges and opportunities. Objectives The objectives of the...

329

Open versus closed loop capacity equilibria in electricity markets ...  

E-Print Network [OSTI]

May 7, 2012 ... Abstract: We consider two game-theoretic models of the generation capacity expansion problem in liberalized electricity markets. The first is an ...

S. Wogrin

2012-05-07T23:59:59.000Z

330

John S. Wright Forestry Center Room Sizes, Capacities, and Rates  

E-Print Network [OSTI]

Appendix 1 John S. Wright Forestry Center Room Sizes, Capacities, and Rates Room College the Wright Center contact: Marlene Mann, Administrative Assistant Forestry and Natural Resources Voice: 765

331

CLEAN-Capacity Building and Training for Low Emissions Development...  

Open Energy Info (EERE)

Development Planning Jump to: navigation, search Tool Summary Name: CLEAN-Capacity Building and Training for Low Emissions Development Planning AgencyCompany Organization:...

332

Optimization of Flexural capacity Of Reinforced fibrous concrete ...  

E-Print Network [OSTI]

Dec 22, 2005 ... Optimization of Flexural capacity Of Reinforced fibrous concrete Beams Using Genetic Algorithm. D Suji (suji_mohan2002 ***at*** yahoo.com)

D Suji

2005-12-22T23:59:59.000Z

333

Optimization of Flexural capacity of Reinforced fibrous Concrete ...  

E-Print Network [OSTI]

Optimizing the flexural capacity of steel fiber reinforced concrete beams, with random ... standard test procedures to be adopted for testing and evaluation of the ...

step1

2005-05-24T23:59:59.000Z

334

DOE Receives Responses on the Implementation of Large-Capacity...  

Broader source: Energy.gov (indexed) [DOE]

Enforcement Guidance on Large-Capacity Clothes Washer Waivers and the Waiver Process Electrolux Gibson Air Conditioner and Equator Clothes Washer Fail DOE Energy Star Testing...

335

assessing nuclear capacity: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

who are familiar Langendoen, Koen 5 Assessing the Control Systems Capacity for Demand Response in Energy Storage, Conversion and Utilization Websites Summary: LBNL-5319E...

336

Selective enrichment of a methanol-utilizing consortium using pulp & paper mill waste streams  

SciTech Connect (OSTI)

Efficient utilization of carbon inputs is critical to the economic viability of the current forest products sector. Input carbon losses occur in various locations within a pulp mill, including losses as volatile organics and wastewater . Opportunities exist to capture this carbon in the form of value-added products such as biodegradable polymers. Waste activated sludge from a pulp mill wastewater facility was enriched for 80 days for a methanol-utilizing consortium with the goal of using this consortium to produce biopolymers from methanol-rich pulp mill waste streams. Five enrichment conditions were utilized: three high-methanol streams from the kraft mill foul condensate system, one methanol-amended stream from the mill wastewater plant, and one methanol-only enrichment. Enrichment reactors were operated aerobically in sequencing batch mode at neutral pH and 25°C with a hydraulic residence time and a solids retention time of four days. Non-enriched waste activated sludge did not consume methanol or reduce chemical oxygen demand. With enrichment, however, the chemical oxygen demand reduction over 24 hour feed/decant cycles ranged from 79 to 89 %, and methanol concentrations dropped below method detection limits. Neither the non-enriched waste activated sludge nor any of the enrichment cultures accumulated polyhydroxyalkanoates (PHAs) under conditions of nitrogen sufficiency. Similarly, the non-enriched waste activated sludge did not accumulate PHAs under nitrogen limited conditions. By contrast, enriched cultures accumulated PHAs to nearly 14% on a dry weight basis under nitrogen limited conditions. This indicates that selectively-enriched pulp mill waste activated sludge can serve as an inoculum for PHA production from methanol-rich pulp mill effluents.

Gregory R. Mockos; William A. Smith; Frank J. Loge; David N. Thompson

2007-04-01T23:59:59.000Z

337

Predicting arsenic concentrations in porewaters of buried uranium mill tailings  

SciTech Connect (OSTI)

The proposed JEB Tailings Management Facility (TMF) to be emplaced below the groundwater table in northern Saskatchewan, Canada, will contain uranium mill tailings from McClean Lake, Midwest and Cigar Lake ore bodies, which are high in arsenic (up to 10%) and nickel (up to 5%). A serious concern is the possibility that high arsenic and nickel concentrations may be released from the buried tailings, contaminating adjacent groundwaters and a nearby lake. Laboratory tests and geochemical modeling were performed to examine ways to reduce the arsenic and nickel concentrations in TMF porewaters so as to minimize such contamination from tailings buried for 50 years and longer. The tests were designed to mimic conditions in the mill neutralization circuit (3 hr tests at 25 C), and in the TMF after burial (5--49 day aging tests). The aging tests were run at 50, 25 and 4 C (the temperature in the TMF). In order to optimize the removal of arsenic by adsorption and precipitation, ferric sulfate was added to tailings raffinates having Fe/As ratios of less than 3--5. The acid raffinates were then neutralized by addition of slaked lime to nominal pH values of 7, 8, or 9. Analysis and modeling of the test results showed that with slaked lime addition to acid tailings raffinates, relatively amorphous scorodite (ferric arsenate) precipitates near pH 1, and is the dominant form of arsenate in slake limed tailings solids except those high in Ni and As and low in Fe, in which cabrerite-annabergite (Ni, Mg, Fe(II) arsenate) may also precipitate near pH 5--6. In addition to the arsenate precipitates, smaller amounts of arsenate are also adsorbed onto tailings solids. The aging tests showed that after burial of the tailings, arsenic concentrations may increase with time from the breakdown of the arsenate phases (chiefly scorodite). However, the tests indicate that the rate of change decreases and approaches zero after 72 hrs at 25 C, and may equal zero at all times in the TMF at 4 C. Consistent with a kinetic model that describes the rate of breakdown of scorodite to form hydrous ferric oxide, the rate of release of dissolved arsenate to tailings porewaters from slake limed tailings: (1) is proportional to pH above pH 6--7; (2) decreases exponentially as the total molar Fe/As ratio of tailings raffinates is increased from 1/1 to greater than 5/1; and (3) is proportional to temperature with an average Arrhenius activation energy of 13.4 {+-} 4.2 kcal/mol. Study results suggest that if ferric sulfate and slaked lime are added in the tailings neutralization circuit to give a raffinate Fe/As molar ratio of at least 3--5 and a nominal (initial) pH of 8 (final pH of 7--8), arsenic and nickel concentrations of 2 mg/L or less, are probable in porewaters of individual tailings in the TMF for 50 to 10,000 yrs after tailings disposal. However, the tailings will be mixed in the TMF, which will contain about 35% tailings with Fe/As = 3.0, and 65% tailings with Fe/As = 5.0--7.7. Thus, it seems likely that average arsenic pore water concentrations in the TMF may not exceed 1 mg/L.

Langmuir, D.; Mahoney, J.; MacDonald, A.; Rowson, J.

1999-10-01T23:59:59.000Z

338

QIP Short Term Course Application of Renewable  

E-Print Network [OSTI]

QIP Short Term Course on Application of Renewable Energy sources (December 11-17, 2013) Course mitigation and credit · PV modules/arrays · Batteries · Hybrid systems (wind, hydro etc.) · Life cycle cost:gntiwari@ces.iitd.ernet.in Application Form QIP Short-Term Course on Applications of Renewable Energy Sources (December 11-17, 2013) Name

Kumar, M. Jagadesh

339

Short stay visa for the Netherlands  

E-Print Network [OSTI]

Short stay visa for the Netherlands #12;1. Why this publication? 2. Who is this publication. Application procedure 7. What should you do on arriving in the Netherlands? 8. Costs 9. Exceptional 15 Contents Immigration and Naturalisation Service | Short stay visa for the Netherlands 2 #12;This

van Suijlekom, Walter

340

Annual status report on the Uranium Mill Tailings Remedial Action Program  

SciTech Connect (OSTI)

This fourteenth annual status report for the Uranium Mill Tailings Remedial Action (UMTRA) Project Office summarizes activities of the Uranium Mill Tailings Remedial Action Surface (UMTRA-Surface) and Uranium Mill Tailings Remedial Action Groundwater (UMTRA-Groundwater) Projects undertaken during fiscal year (FY) 1992 by the US Department of Energy (DOE) and other agencies. Project goals for FY 1993 are also presented. An annual report of this type was a statutory requirement through January 1, 1986, pursuant to the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law (PL) 95-604. The DOE will continue to submit annual reports to DOE-Headquarters, the states, tribes, and local representatives through Project completion in order to inform the public of the yearly Project status. The purpose of the remedial action is to stabilize and control the tailings and other residual radioactive material (RRM) located on the inactive uranium processing sites in a safe and environmentally sound manner, and to minimize or eliminate potential health hazards. Commercial and residential properties near designated processing sites that are contaminated with material from the sites, herein referred to as ``vicinity properties (VP),`` are also eligible for remedial action. Included in the UMTRA Project are 24 inactive uranium processing sites and associated VPs located in 10 states, and the VPs associated with the Edgemont, South Dakota, uranium mill currently owned by the Tennessee Valley Authority (TVA) (Figure A.1, Appendix A).

Not Available

1992-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Towards Optimal Capacity Segmentation with Hybrid Cloud Pricing  

E-Print Network [OSTI]

and EC2 spot market. Furthermore, we formulate the optimal capacity segmentation strategy as a MarkovTowards Optimal Capacity Segmentation with Hybrid Cloud Pricing Wei Wang, Baochun Li, and Ben Liang markets with different service guarantees. For example, Amazon EC2 prices virtual instances under three

Li, Baochun

342

Towards Optimal Capacity Segmentation with Hybrid Cloud Pricing  

E-Print Network [OSTI]

between periodic auctions and EC2 spot market. Furthermore, we formulate the optimal capacity segmentationTowards Optimal Capacity Segmentation with Hybrid Cloud Pricing Wei Wang, Baochun Li, and Ben Liang priced in multiple markets with different service guarantees. For example, Amazon EC2 prices virtual

Li, Baochun

343

Mechanism Design for Capacity Allocation with Price Competition  

E-Print Network [OSTI]

. This paper examines the problem of mechanism design for capacity allocation in two connected markets whereMechanism Design for Capacity Allocation with Price Competition Masabumi Furuhata Intelligent-users in price competition. We consider the problems of how allocation mechanisms in the upstream market de

Zhang, Dongmo

344

Complexity, Capacity, and Capture Nolan McCarty  

E-Print Network [OSTI]

financial markets and products are so complex that outgunned agencies lack the capacity to detect systemicComplexity, Capacity, and Capture Nolan McCarty July 13, 2011 Susan Dod Brown Professor: nmccarty@princeton.edu #12;1 Introduction In the debates on financial market reform that followed

345

Prediction methods for capacity of drag anchors in clayey soils  

E-Print Network [OSTI]

A drag anchor is a marine foundation element, which is penetrated into the seabed by dragging in order to generate a required capacity. The holding capacity of a drag anchor in a particular soil condition is developed by soil resistance acting...

Yoon, Yeo Hoon

2002-01-01T23:59:59.000Z

346

THE MAXIMUM CAPACITY OF A LINE PLAN IS INAPPROXIMABLE  

E-Print Network [OSTI]

THE MAXIMUM CAPACITY OF A LINE PLAN IS INAPPROXIMABLE CHRISTINA PUHL AND SEBASTIAN STILLER Abstract a network, upper arc-capacities and a line pool. E-mail: puhl@math.tu-berlin.de, stiller of the European Commission under contract no. FP6-021235-2. 1 #12;2 CHRISTINA PUHL AND SEBASTIAN STILLER We

Nabben, Reinhard

347

Adaptive Online Battery Parameters/SOC/Capacity Co-estimation  

E-Print Network [OSTI]

and even storage ageing of the battery. Following our previous publications in which we developed an onlineAdaptive Online Battery Parameters/SOC/Capacity Co-estimation Habiballah Rahimi-Eichi and Mo parameters to characterize the performance and application of a battery. Although the nominal capacity

Chow, Mo-Yuen

348

Energy-Efficient Capacity Optimization in Wireless Networks  

E-Print Network [OSTI]

Energy-Efficient Capacity Optimization in Wireless Networks Lu Liu, Xianghui Cao, Yu Cheng, Lili Du capacity in the most energy-efficient manner over a general large-scale wireless network, say, a multi numerical results demonstrate the energy efficiency improvement by the proposed energy-efficient

Wang, Yu

349

Figure 4: Case study network Maximising Renewable Capacity  

E-Print Network [OSTI]

. A variety of techniques have been used for distribution system optimisations. Here, Optimal Power Flow (OPF at several combinations of locations (DG at 0.9 lagging power factor). 3.5 MW of capacity is foundW is allocated at A. Without network reinforcement connection of the full 3.5 MW of mini-hydro capacity

Harrison, Gareth

350

MASTERS REPORT ANALYSIS AND MODELING OF ACID NEUTRALIZING CAPACITY  

E-Print Network [OSTI]

itself against acidification and is used to monitor the effect of acid rain on watersheds. From 1993MASTERS REPORT ANALYSIS AND MODELING OF ACID NEUTRALIZING CAPACITY IN THE MID-ATLANTIC HIGHLANDS UNIVERSITY #12;ABSTRACT Acid Neutralizing Capacity (ANC) is a measure of a solution's ability to buffer

351

Building Partnership Capacity and Sustainability in Financially Challenging Times  

E-Print Network [OSTI]

Building Partnership Capacity and Sustainability in Financially Challenging Times Introduction educational inequality. Partnership Question From the outset, the core objective was to design a sustainable that by focusing on capacity building and sustainability from the beginning, it is possible to build a partnership

352

Calculation of the number of cancer deaths prevented by the Uranium Mill Tailings Remedial Action Project  

SciTech Connect (OSTI)

The Uranium Mill Tailings Remedial Action Project has completed remedial action at 22 uranium mill tailings sites and about 5,000 properties (vicinity properties) where tailings were used in construction, at a total cost of $1.45 billion. This paper uses existing data from Environmental Impact Statements and Environmental Assessments, and vicinity property calculations, to determine the total number of cancer deaths averted by the Uranium Mill Tailings Remedial Action Project. The cost-effectiveness of remediating each site, the vicinity properties, and the entire project is calculated. The cost per cancer death averted was four orders of magnitude higher at the least cost-effective site than at the most cost-effective site.

Miller, M.L.; Pomatto, C.B. (Roy F. Weston, Inc., Albuquerque, NM (United States)); Cornish, R.E. (Dept. of Energy, Albuquerque, NM (United States). Albuquerque Operations Office)

1999-05-01T23:59:59.000Z

353

Cleanup of inactive Uranium Mill Tailings Sites in the Navajo Nation  

SciTech Connect (OSTI)

The U.S. Congress passed the Uranium Mill Tailings Radiation Control Act (UMTRCA) in 1978 to address potential and significant radiation health hazards to the public from active and inactive mill operations. Title I to the UMTRCA identified sites to be designated for remedial action. These include four uranium mill tailings remedial action (UMTRA) sites in the Navajo Nation. These sites are located in Shiprock, New Mexico; Tuba City, Arizona; Cane Valley, Arizona; and Halchita, Utah. The U.S. Department of Energy (DOE) was directed to select and execute a plan of remedial action that provides long-term stabilization and control of radioactive materials and satisfies the U.S. Environmental Protection Agency standards and other applicable laws and regulations.

Martin, B.

1994-12-31T23:59:59.000Z

354

Decommissioning of facilities and encapsulation of wastes for an uranium mill site in Spain  

SciTech Connect (OSTI)

In the south of Spain on the outskirts of the town of Andujar an inactive uranium mill tailings site is being remediated in place. Mill equipment, buildings and process facilities have been dismantled and demolished and the resulting metal wastes and debris have been placed in the tailings pile. The tailings mass has been reshaped by flattening the sideslopes to improve stability and a cover system has been placed over the pile. Remedial action works started in February 1991 and will be completed by March 1994. This paper describes the progress of the remediation works for the closure of the Andujar mill site and in particular discusses the approaches used for the dismantling and demolition of the processing facilities and the stabilization of the tailings pile.

Santiago, J.L. [Enresa, Madrid (Spain); Sanchez, M. [Initec, Madrid (Spain)

1994-12-31T23:59:59.000Z

355

Scientific basis for risk assessment and management of uranium mill tailings  

SciTech Connect (OSTI)

A National Research Council study panel, convened by the Board on Radioactive Waste Management, has examined the scientific basis for risk assessment and management of uranium mill tailings and issued this final report containing a number of recommendations. Chapter 1 provides a brief introduction to the problem. Chapter 2 examines the processes of uranium extraction and the mechanisms by which radionuclides and toxic chemicals contained in the ore can enter the environment. Chapter 3 is devoted to a review of the evidence on health risks associated with radon and its decay products. Chapter 4 provides a consideration of conventional and possible new technical alternatives for tailings management. Chapter 5 explores a number of issues of comparative risk, provides a brief history of uranium mill tailings regulation, and concludes with a discussion of choices that must be made in mill tailing risk management. 211 refs., 30 figs., 27 tabs.

Not Available

1986-01-01T23:59:59.000Z

356

Assessment of the radiological impact of the inactive uranium-mill tailings at Mexican Hat, Utah  

SciTech Connect (OSTI)

High surface soil concentrations of /sup 226/Ra and high above-ground measurements of gamma-ray intensity in the vicinity of the inactive uranium-mill tailings at Mexican Hat show both wind and water erosion of the tailings. The former mill area, occupied by a trade school at the time of this survey, shows a comparatively high level of contamination, probably from unprocessed ore on the surface of the ore storage area near the location of the former mill buildings. However, the estimated health effect of exposure to gamma rays during a 2000-hr work year in the area represents an increase of 0.1% in the risk of death from cancer. Exposure of less than 600 persons within 1.6 km of the tailings to radon daughters results in an estimated 0.2%/year increase in risk of lung cancer.

Haywood, F.F.; Goldsmith, W.A.; Ellis, B.S.; Hubbard, H.M. Jr.; Fox, W.F.; Shinpaugh, W.H.

1980-03-01T23:59:59.000Z

357

Radiological survey of the inactive uranium-mill tailings at Rifle, Colorado  

SciTech Connect (OSTI)

Results of radiological surveys of two inactive uranium-mill sites near Rifle, Colorado, in May 1976 are presented. These sites are referred to as Old Rifle and New Rifle. The calculated /sup 226/Ra inventory of the latter site is much higher than at the older mill location. Data on above-ground measurements of gamma exposure rates, surface and near-surface concentration of /sup 226/Ra in soil and sediment samples, concentration of /sup 226/Ra in water, calculated subsurface distribution of /sup 226/Ra, and particulate radionuclide concentrations in air samples are given. The data serve to define the extent of contamination in the vicinity of the mill sites and their immediate surrounding areas with tailings particles. Results of these measurements were utilized as technical input for an engineering assessment of these two sites.

Haywood, F.F.; Jacobs, D.J.; Ellis, B.S.; Hubbard, H.M. Jr.; Shinpaugh, W.H.

1980-06-01T23:59:59.000Z

358

Social Logics in Development of Institutional Capacity The Case of Capacity Development for the Clean Development Mechanism in Uganda  

E-Print Network [OSTI]

for the Clean Development Mechanism in Uganda Karen Holm Olsen International Development Studies Department in Uganda 2002-2006. The study finds that the politics of institutional change processes are largely ignored of Institutional Capacity The case of Capacity Development for the CDM in Uganda The 15th International Climate

359

Plant foliar disease suppression mediated by composted forms of paper mill residuals exhibits molecular features of induced resistance  

E-Print Network [OSTI]

Plant foliar disease suppression mediated by composted forms of paper mill residuals exhibits Arabidopsis thaliana grown in soil from field plots amended with composted forms of paper mill residuals (PMR with plants grown in soil from field plots amended with a non-composted PMR or non-amended soils. Similar

Goodman, Robert M.

360

Improvement effect of small scale recycled milled carbon fibre in DGEBA epoxy resin creating an improved matrix  

E-Print Network [OSTI]

energy [4, 5]. Also, till the last decade fibre reinforced composite materials were regarded as non, 10]. The reinforced material used in this paper is recycled milled carbon fibre (MCF). Addition1 Improvement effect of small scale recycled milled carbon fibre in DGEBA epoxy resin creating

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Bayesian models for elevated disease risk due to exposure to uranium mine and mill waste on the Navajo Nation  

E-Print Network [OSTI]

ForReview Only Bayesian models for elevated disease risk due to exposure to uranium mine and mill of Pharmacy, Community Environmental Health Program Keywords: abandoned uranium mines, conditionally specified to ex- posure to uranium mine and mill waste on the Navajo Nation Glenn A. Stark University of New

Huerta, Gabriel

362

2004-2005 Texas Water Resources Institute Mills Scholarship Application Water Management, Soil Salinity and Landscape Ecology in Laguna  

E-Print Network [OSTI]

: Bruce Herbert (O) 979-845-2405 herbert@geo.tamu.edu #12;Heather R. Miller 2004-05 TWRI Mills 2 Water2004-2005 Texas Water Resources Institute Mills Scholarship Application Water Management, Soil Salinity and Landscape Ecology in Laguna Atascosa National Wildlife Refuge Heather R. Miller Department

Herbert, Bruce

363

Extended Kalman Filter Based Neural Networks Controller For Hot Strip Rolling mill  

SciTech Connect (OSTI)

The present paper deals with the application of an Extended Kalman filter based adaptive Neural-Network control scheme to improve the performance of a hot strip rolling mill. The suggested Neural Network model was implemented using Bayesian Evidence based training algorithm. The control input was estimated iteratively by an on-line extended Kalman filter updating scheme basing on the inversion of the learned neural networks model. The performance of the controller is evaluated using an accurate model estimated from real rolling mill input/output data, and the usefulness of the suggested method is proved.

Moussaoui, A. K. [Electrical Engineering Laboratory of Guelma (LGEG), BP.401, University of Guelma, 24000 (Algeria); Abbassi, H. A.; Bouazza, S. [Universite Badji Mokhtar BP 12--23000-Annaba Algerie (Algeria)

2008-06-12T23:59:59.000Z

364

Uranium Mill Tailings Remedial Action (UMTRA) Surface Project: Project plan. Revision 1  

SciTech Connect (OSTI)

The Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA) [Public Law (PL) 95-604, 42 United States Code (USC) 7901], hereinafter referred to as the ``Act,`` authorizes the US Department of Energy (DOE) to stabilize and control surface tailings and ground water contamination. To fulfill this mission, the DOE has established two projects under the Uranium Mill Tailings Remedial Action (UMTRA) Project Office. The Ground Water Project was established in April 1991 as a major project and a separate project plan will be prepared for that portion of the mission. This project plan covers the UMTRA Surface Project, a major system acquisition (MSA).

Not Available

1993-08-11T23:59:59.000Z

365

Environmental assessment of remedial action at the Spook uranium mill tailings site, Converse County, Wyoming  

SciTech Connect (OSTI)

This document assesses a joint remedial action proposed by the US Department of Energy Uranium Mill Tailings Remedial Action Project and the State of Wyoming Abandoned Mine Lands Program. The proposed action would consist of stabilizing uranium mill tailings and other associated contaminated materials within an inactive open pit mine on the site; backfilling the open pit with overburden materials that would act as a radon barrier and cover; and recontouring and seeding all disturbed areas to premining conditions. The impacts of no action at this site are addressed as the alternative to the proposed action. 74 refs., 12 figs., 19 tabs.

Not Available

1989-04-01T23:59:59.000Z

366

Direct-write milling of diamond by a focused oxygen ion beam  

E-Print Network [OSTI]

Recent advances in focused ion beam technology have enabled high-resolution, direct-write nanofabrication using light ions. Studies with light ions to date have, however, focused on milling of materials where sub-surface ion beam damage does not inhibit device performance. Here we report on direct-write milling of single crystal diamond using a focused beam of oxygen ions. Material quality is assessed by Raman and luminescence analysis, and reveals that the damage layer generated by oxygen ions can be removed by nonintrusive post-processing methods such as localised electron beam induced chemical etching.

Martin, Aiden A; Botman, Aurelien; Toth, Milos; Aharonovich, Igor

2015-01-01T23:59:59.000Z

367

Compilation techniques for short-vector instructions  

E-Print Network [OSTI]

Multimedia extensions are nearly ubiquitous in today's general-purpose processors. These extensions consist primarily of a set of short-vector instructions that apply the same opcode to a vector of operands. This design ...

Larsen, Samuel (Samuel Barton), 1975-

2006-01-01T23:59:59.000Z

368

Gravitational waves and short gamma ray bursts.  

E-Print Network [OSTI]

??Short hard gamma-ray bursts (GRB) are believed to be produced by compact binary coalescences (CBC) { either double neutron stars or neutron star{black hole binaries.… (more)

Predoi, Valeriu

2012-01-01T23:59:59.000Z

369

8 Short life stories: Dorti Peterson  

E-Print Network [OSTI]

last updated on Monday, 4 April 2011 Accession Form for Individual Recordings: Collection / Collector Name Stephen Leonard Tape No. / Track / Item No. 8 Length of track 33 minutes Title of track Short life stories: Dorti Peterson Translation...

Leonard, Stephen Pax

370

Monitoring the Performance of an Alternative Landfill Cover at the Monticello, Utah, Uranium Mill Tailings Disposal Site  

SciTech Connect (OSTI)

The U.S. Department of Energy Office of Legacy Management (DOE) and the U.S. Environmental Protection Agency (EPA) collaborated on the design and monitoring of an alternative cover for the Monticello uranium mill tailings disposal cell, a Superfund site in southeastern Utah. Ground-water recharge is naturally limited at sites like Monticello where thick, fine-textured soils store precipitation until evaporation and plant transpiration seasonally return it to the atmosphere. The cover at Monticello uses local soils and a native plant community to mimic the natural soil water balance. The cover is fundamentally an evapotranspiration (ET) design with a capillary barrier. A 3-hectare drainage lysimeter was embedded in the cover during construction of the disposal cell in 2000. The lysimeter consists of a geo-membrane liner below the capillary barrier that directs percolation water to a monitoring system. Soil water storage is determined by integration of point water content measurements. Meteorological parameters are measured nearby. Plant cover, shrub density, and leaf area index (LAI) are monitored annually. The cover performed well over the 7-year monitoring period (2000-2007). The cumulative percolation was 4.2 mm (0.6 mm yr{sup -1}), satisfying an EPA goal of an average percolation of <3.0 mm yr{sup -1}. Almost all percolation can be attributed to the exceptionally wet winter and spring of 2004-2005 when soil water content slightly exceeded the water storage capacity of the cover. The diversity, percent cover, and LAI of vegetation increased over the monitoring period, although the density of native shrubs that extract water from deeper in the cover has remained less than revegetation targets. DOE and EPA are applying the monitoring results to plan for long-term surveillance and maintenance and to evaluate alternative cover designs for other waste disposal sites. (authors)

Waugh, W.J.; Kastens, M.K.; Sheader, L.R.L. [Environmental Sciences Laboratory, Grand Junction, CO (United States); Benson, C.H. [University of Wisconsin, Madison, WI (United States); Albright, W.H. [Desert Research Institute, Reno, NV (United States); Mushovic, P.S. [U.S. Environmental Protection Agency, Denver, CO (United States)

2008-07-01T23:59:59.000Z

371

Heat capacity of liquids: an approach from the solid phase  

E-Print Network [OSTI]

We calculate the energy and heat capacity of a liquid on the basis of its elastic properties and vibrational states. The experimental decrease of liquid heat capacity with temperature is attributed to the increasing loss of two transverse modes with frequency $\\omegaliquid relaxation time. In a simple model, liquid heat capacity is related to viscosity and is compared with the experimental data of mercury. We also calculate the vibrational energy of a quantum liquid, and show that transverse phonons can not be excited in the low-temperature limit. Finally, we discuss the implications of the proposed approach to liquids for the problem of glass transition.

Kostya Trachenko

2008-08-20T23:59:59.000Z

372

European Wind Energy Conference & Exhibition EWEC 2003, Madrid, Spain. State-of-the-Art on Methods and Software Tools for Short-Term  

E-Print Network [OSTI]

European Wind Energy Conference & Exhibition EWEC 2003, Madrid, Spain. State-of-the-Art on Methods and Software Tools for Short-Term Prediction of Wind Energy Production G. Giebel*, L. Landberg, Risoe National Roskilde, Denmark Abstract: The installed wind energy capacity in Europe today is 20 GW, while

Paris-Sud XI, Université de

373

Effect Of Oxidation On Chromium Leaching And Redox Capacity Of Slag-Containing Waste Forms  

SciTech Connect (OSTI)

The rate of oxidation is important to the long-term performance of reducing salt waste forms because the solubility of some contaminants, e.g., technetium, is a function of oxidation state. TcO{sub 4}{sup ?} in the salt solution is reduced to Tc(IV) and has been shown to react with ingredients in the waste form to precipitate low solubility sulfide and/or oxide phases [Shuh, et al., 1994, Shuh, et al., 2000, Shuh, et al., 2003]. Upon exposure to oxygen, the compounds containing Tc(IV) oxidize to the pertechnetate ion, Tc(VII)O{sub 4}{sup ?}, which is very soluble. Consequently the rate of technetium oxidation front advancement into a monolith and the technetium leaching profile as a function of depth from an exposed surface are important to waste form performance and ground water concentration predictions. An approach for measuring contaminant oxidation rate (effective contaminant specific oxidation rate) based on leaching of select contaminants of concern is described in this report. In addition, the relationship between reduction capacity and contaminant oxidation is addressed. Chromate was used as a non-radioactive surrogate for pertechnetate in simulated waste form samples. Depth discrete subsamples were cut from material exposed to Savannah River Site (SRS) ''field cured'' conditions. The subsamples were prepared and analyzed for both reduction capacity and chromium leachability. Results from field-cured samples indicate that the depth at which leachable chromium was detected advanced further into the sample exposed for 302 days compared to the sample exposed to air for 118 days (at least 50 mm compared to at least 20 mm). Data for only two exposure time intervals is currently available. Data for additional exposure times are required to develop an equation for the oxidation front progression. Reduction capacity measurements (per the Angus-Glasser method, which is a measurement of the ability of a material to chemically reduce Ce(IV) to Ce(III) in solution) performed on depth discrete samples could not be correlated with the amount of chromium leached from the depth discrete subsamples or with the oxidation front inferred from soluble chromium (i.e., effective Cr oxidation front). Exposure to oxygen (air or oxygen dissolved in water) results in the release of chromium through oxidation of Cr(III) to highly soluble chromate, Cr(VI). Residual reduction capacity in the oxidized region of the test samples indicates that the remaining reduction capacity is not effective in re-reducing Cr(VI) in the presence of oxygen. Consequently, this method for determining reduction capacity may not be a good indicator of the effective contaminant oxidation rate in a relatively porous solid (40 to 60 volume percent porosity). The chromium extracted in depth discrete samples ranged from a maximum of about 5.8 % at about 5 mm (118 day exposure) to about 4 % at about 10 mm (302 day exposure). The use of reduction capacity as an indicator of long-term performance requires further investigation. The carbonation front was also estimated to have advanced to at least 28 mm in 302 days based on visual observation of gas evolution during acid addition during the reduction capacity measurements. Depth discrete sampling of materials exposed to realistic conditions in combination with short term leaching of crushed samples has potential for advancing the understanding of factors influencing performance and will support conceptual model development.

Almond, P. M.; Stefanko, D. B.; Langton, C. A.

2013-03-01T23:59:59.000Z

374

Evaluation and capacity building to improve precollege science and mathematics achievement in the US: 10 CFR, Part 605  

SciTech Connect (OSTI)

The National Center for Improving Science Education has undertaken activities to achieve evaluation goals for DOE's Precollege programs: develop means to determine program quality; develop means for determining the contribution of DOE precollege programs to both teacher enhancement and student achievement; provide evaluation designs and instruments and reports of program quality and impact; and strengthen both DOE's and the Labs' capacity to do both short- and long-term planning as well as deliver effective programs and evaluation. Appendices include evaluation/technical assistance report, profiling teacher research participation and teacher development programs, teacher surveys, impact assessment design, and teacher research participation programs anecdotes for 8 labs.

Not Available

1992-01-01T23:59:59.000Z

375

Developing A New High Capacity Anode With Long Cycle Life  

Broader source: Energy.gov (indexed) [DOE]

more than 1000 mAhg with poor cyleability. * The formation of Sn x Co y C z and MO composite could lead to the increase in the capacity, reduce the amount of cobalt in the...

376

Fail Safe Design for Large Capacity Lithium-ion Batteries  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Fail Safe Design for Large Capacity Lithium-ion Batteries NREL Commercialization & Tech Transfer Webinar March 27, 2011 Gi-Heon Kim gi-heon.kim@nrel.gov John Ireland, Kyu-Jin Lee,...

377

MIMO capacity convergence in frequency-selective channels  

E-Print Network [OSTI]

The dependence of multi-antenna capacity on bandwidth is characterized empirically for narrowband, wideband and ultrawideband indoor channels using spatial and polar arrays. It is shown that both the mean and the outage ...

Malik, Wasim Q.

378

Creative agencies : a model for building community capacity  

E-Print Network [OSTI]

This research investigates how existing initiatives based in artistic and non-artistic disciplines build indigenous capacity for leadership in disenfranchised communities through the application of the creative process. ...

Ramaccia, Elizabeth M. (Elizabeth Marie)

2011-01-01T23:59:59.000Z

379

Capacity Requirements to Support Inter-Balancing Area Wind Delivery  

SciTech Connect (OSTI)

Paper examines the capacity requirements that arise as wind generation is integrated into the power system and how those requirements change depending on where the wind energy is delivered.

Kirby, B.; Milligan, M.

2009-07-01T23:59:59.000Z

380

Comparing capacities and delays at major European and American airports  

E-Print Network [OSTI]

Successful air transport systems must satisfy the demand for flights while maintaining a high level of service and safety. For airports, which have limited capacities, policy-makers must compromise between maximizing the ...

Morisset, Thomas (Thomas Marc)

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Real options approach to capacity planning under uncertainty  

E-Print Network [OSTI]

This thesis highlights the effectiveness of Real Options Analysis (ROA) in capacity planning decisions for engineering projects subject to uncertainty. This is in contrast to the irreversible decision-making proposed by ...

Mittal, Geetanjali, 1979-

2004-01-01T23:59:59.000Z

382

Development of operations based long range network capacity planning models  

E-Print Network [OSTI]

Planning for vaccines manufacturing capacity is both a complex task requiring many inputs and an important function of manufacturers to ensure the supply of vaccines that prevent life-threatening illnesses. This thesis ...

Wilson, Cynthia M. (Cynthia Marie)

2011-01-01T23:59:59.000Z

383

Capacity planning and change management in an aerospace overhaul cell  

E-Print Network [OSTI]

Purpose - This thesis analyzes the transformation of the Small Components Cell in Pratt & Whitney's aftermarket division through lean manufacturing techniques. The thesis focuses on use of a labor capacity planning model, ...

Walker, David, M.B.A. Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

384

High capacity stabilized complex hydrides for hydrogen storage  

DOE Patents [OSTI]

Complex hydrides based on Al(BH.sub.4).sub.3 are stabilized by the presence of one or more additional metal elements or organic adducts to provide high capacity hydrogen storage material.

Zidan, Ragaiy; Mohtadi, Rana F; Fewox, Christopher; Sivasubramanian, Premkumar

2014-11-11T23:59:59.000Z

385

Nitrogen expander cycles for large capacity liquefaction of natural gas  

SciTech Connect (OSTI)

Thermodynamic study is performed on nitrogen expander cycles for large capacity liquefaction of natural gas. In order to substantially increase the capacity, a Brayton refrigeration cycle with nitrogen expander was recently added to the cold end of the reputable propane pre-cooled mixed-refrigerant (C3-MR) process. Similar modifications with a nitrogen expander cycle are extensively investigated on a variety of cycle configurations. The existing and modified cycles are simulated with commercial process software (Aspen HYSYS) based on selected specifications. The results are compared in terms of thermodynamic efficiency, liquefaction capacity, and estimated size of heat exchangers. The combination of C3-MR with partial regeneration and pre-cooling of nitrogen expander cycle is recommended to have a great potential for high efficiency and large capacity.

Chang, Ho-Myung; Park, Jae Hoon; Gwak, Kyung Hyun [Hong Ik University, Department of Mechanical Engineering, Seoul, 121-791 (Korea, Republic of); Choe, Kun Hyung [Korea Gas Corporation, Incheon, 406-130 (Korea, Republic of)

2014-01-29T23:59:59.000Z

386

Why Are We Talking About Capacity Markets? (Presentation)  

SciTech Connect (OSTI)

Capacity markets represent a new and novel way to achieve greater economic use of variable generation assets such as wind and solar, and this concept is discussed in this presentation.

Milligan, M.

2011-06-01T23:59:59.000Z

387

Strategies for Sharing Bottleneck Capacity among Buses and Cars  

E-Print Network [OSTI]

at first, since bus-car sharing strategies for facilities ofsharing the middle link’s median lane between cars andfor Sharing Bottleneck Capacity among Buses and Cars by

Guler, Sukran Ilgin

2012-01-01T23:59:59.000Z

388

Design and Evaluation of Novel High Capacity Cathode Materials...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

17johnson2011p.pdf More Documents & Publications Design and Evaluation of Novel High Capacity Cathode Materials Lithium Source For High Performance Li-ion Cells Lithium Source...

389

,"New York Natural Gas Underground Storage Capacity (MMcf)"  

U.S. Energy Information Administration (EIA) Indexed Site

,,"(202) 586-8800",,,"2262015 9:17:17 AM" "Back to Contents","Data 1: New York Natural Gas Underground Storage Capacity (MMcf)" "Sourcekey","N5290NY2"...

390

Capacity planning and admission control policies for intensive care units  

E-Print Network [OSTI]

Poor management of the patient flow in intensive care units (ICUs) causes service rejections and presents significant challenges from the standpoint of capacity planning and management in ICUs. This thesis reports on the ...

Chaiwanon, Wongsakorn

2010-01-01T23:59:59.000Z

391

Increasing Freeway Merge Capacity Through On-Ramp Metering  

E-Print Network [OSTI]

Hall, F. L. and Agywmang-Duah, K. (1991), Freeway capacity1990; Hall and Agyemang-Duah, 1991). As explained below,Later, Hall and Agyemang- Duah (1991) studied a freeway

Rudjanakanoknad, Jittichai

2005-01-01T23:59:59.000Z

392

Genetic Regulation of Intrinsic Endurance Exercise Capacity in Mice  

E-Print Network [OSTI]

been reported across cross-section, twin, and family studies. This variation is evidence of a genetic component to the phenotype of endurance exercise capacity: however, the genetic factors responsible for explaining this variation are undefined...

Courtney, Sean M.

2013-07-26T23:59:59.000Z

393

Creative capacity building in post-conflict Uganda  

E-Print Network [OSTI]

Creative Capacity Building (CCB) is a methodology that emphasizes the ability of people living in poverty to create livelihood technologies, i.e., machines and tools that increase income, improve health and safety, decrease ...

Taha, Kofi A. (Kofi Abdul Malik)

2011-01-01T23:59:59.000Z

394

Tri-Laboratory Linux Capacity Cluster 2007 SOW  

SciTech Connect (OSTI)

The Advanced Simulation and Computing (ASC) Program (formerly know as Accelerated Strategic Computing Initiative, ASCI) has led the world in capability computing for the last ten years. Capability computing is defined as a world-class platform (in the Top10 of the Top500.org list) with scientific simulations running at scale on the platform. Example systems are ASCI Red, Blue-Pacific, Blue-Mountain, White, Q, RedStorm, and Purple. ASC applications have scaled to multiple thousands of CPUs and accomplished a long list of mission milestones on these ASC capability platforms. However, the computing demands of the ASC and Stockpile Stewardship programs also include a vast number of smaller scale runs for day-to-day simulations. Indeed, every 'hero' capability run requires many hundreds to thousands of much smaller runs in preparation and post processing activities. In addition, there are many aspects of the Stockpile Stewardship Program (SSP) that can be directly accomplished with these so-called 'capacity' calculations. The need for capacity is now so great within the program that it is increasingly difficult to allocate the computer resources required by the larger capability runs. To rectify the current 'capacity' computing resource shortfall, the ASC program has allocated a large portion of the overall ASC platforms budget to 'capacity' systems. In addition, within the next five to ten years the Life Extension Programs (LEPs) for major nuclear weapons systems must be accomplished. These LEPs and other SSP programmatic elements will further drive the need for capacity calculations and hence 'capacity' systems as well as future ASC capability calculations on 'capability' systems. To respond to this new workload analysis, the ASC program will be making a large sustained strategic investment in these capacity systems over the next ten years, starting with the United States Government Fiscal Year 2007 (GFY07). However, given the growing need for 'capability' systems as well, the budget demands are extreme and new, more cost effective ways of fielding these systems must be developed. This Tri-Laboratory Linux Capacity Cluster (TLCC) procurement represents the ASC first investment vehicle in these capacity systems. It also represents a new strategy for quickly building, fielding and integrating many Linux clusters of various sizes into classified and unclassified production service through a concept of Scalable Units (SU). The programmatic objective is to dramatically reduce the overall Total Cost of Ownership (TCO) of these 'capacity' systems relative to the best practices in Linux Cluster deployments today. This objective only makes sense in the context of these systems quickly becoming very robust and useful production clusters under the crushing load that will be inflicted on them by the ASC and SSP scientific simulation capacity workload.

Seager, M

2007-03-22T23:59:59.000Z

395

Timber Products' Mississippi mill earns formaldehyde certification Tuesday, February 10, 2009 -Modern Woodworking  

E-Print Network [OSTI]

., have been certified to meet the California Air Resources Board (CARB) requirements. Timber Products of the California Air Resources Board (CARB). Corinth's designation means that all Timber Products hardwood plywoodTimber Products' Mississippi mill earns formaldehyde certification Tuesday, February 10, 2009

396

Elemental composition of airborne particulates in uranium mining and milling operations  

SciTech Connect (OSTI)

Airborne particulates were collected through filters in occupational areas of the uranium mining and milling complex located in Pocos de Caldas, Brazil. The filters were analyzed by microPIXE (particle induced x-ray emission) combined with Rutherford Backscattering (RBS) of the incident protons. The results are discussed in the paper. 4 references, 6 figures, 1 table.

Paschoa, A.S.; Wrenn, M.E.; Jones, K.W.; Cholewa, M.; Carvalho, S.M.

1984-01-01T23:59:59.000Z

397

Mobile water treatment plant special study. Uranium Mill Tailings Remedial Action Project  

SciTech Connect (OSTI)

Characterization of the level and extent of groundwater contamination in the vicinity of Title I mill sites began during the surface remedial action stage (Phase 1) of the Uranium Mill Tailings Remedial Action (UMTRA) Project. Some of the contamination in the aquifer(s) at the abandoned sites is attributable to milling activities during the years the mills were in operation. To begin implementation of Phase 11 groundwater remediation, the US Department of Energy (DOE) requested that (1) the Technical Assistance Contractor (TAC) conduct a study to provide for the design of a mobile water treatment plant to treat groundwater extracted during site characterization studies at completed Phase I UMTRA sites, and (2) the results of the TAC investigations be documented in a special study report. This special study develops the design criteria for a water treatment plant that can be readily transported from one UMTRA site to another and operated as a complete treatment system. The 1991 study provides the basis for selecting a mobile water treatment system to meet the operating requirements recommended in this special study. The scope of work includes the following: Determining contaminants, flows, and loadings. Setting effluent quality criteria. Sizing water treatment unit(s). Evaluating non-monetary aspects of alternate treatment processes. Comparing costs of alternate treatment processes. Recommending the mobile water treatment plant design criteria.

Not Available

1992-12-01T23:59:59.000Z

398

Selection of water treatment processes special study. [Uranium Mill Tailings Remedial Action (UMTRA) Project  

SciTech Connect (OSTI)

Characterization of the level and extent of groundwater contamination in the vicinity of Title I mill sites began during the surface remedial action stage (Phase 1) of the Uranium Mill Tailings Remedial Action (UMTRA) Project. Some of the contamination in the aquifer(s) at the abandoned sites is attributable to milling activities during the years the mills were in operation. The restoration of contaminated aquifers is to be undertaken in Phase II of the UMTRA Project. To begin implementation of Phase II, DOE requested that groundwater restoration methods and technologies be investigated by the Technical Assistance Contractor (TAC). and that the results of the TAC investigations be documented in special study reports. Many active and passive methods are available to clean up contaminated groundwater. Passive groundwater treatment includes natural flushing, geochemical barriers, and gradient manipulation by stream diversion or slurry walls. Active groundwater.cleanup techniques include gradient manipulation by well extraction or injection. in-situ biological or chemical reclamation, and extraction and treatment. Although some or all of the methods listed above may play a role in the groundwater cleanup phase of the UMTRA Project, the extraction and treatment (pump and treat) option is the only restoration alternative discussed in this report. Hence, all sections of this report relate either directly or indirectly to the technical discipline of process engineering.

Not Available

1991-11-01T23:59:59.000Z

399

Environmental assessment of remedial action at the Slick Rock uranium mill tailings sites, Slick Rock, Colorado  

SciTech Connect (OSTI)

The Uranium Mill Tailings Radiation Control Act of 1978, hereafter referred to as the UMTRCA, authorized the US Department of Energy (DOE) to clean up two uranium mill tailings processing sites near Slick Rock, Colorado, in San Miguel County. The purpose of the cleanup is to reduce the potential health effects associated with the radioactive materials remaining on the processing sites and on vicinity properties (VPs) associated with the sites. The US Environmental Protection Agency (EPA) promulgated standards for the UMTRCA that contained measures to control the contaminated materials and to protect the ground water from further degradation. The sites contain concrete foundations of mill buildings, tailings piles, and areas contaminated by windblown and waterborne radioactive tailings materials. The proposed action is to remediate the UC and NC sites by removing all contaminated materials within the designated site boundaries or otherwise associated with the sites, and relocating them to, and stabilizing them at, a location approximately 5 road mi (8 km) northeast of the processing sites on land administered by the US Bureau of Land Management (BLM). Remediation would be performed by the DOE`s Uranium Mill Tailings Remedial Action (UMTRA) Project.

NONE

1995-01-01T23:59:59.000Z

400

BismuthCeramic Nanocomposites with Unusual Thermal Stability via High-Energy Ball Milling**  

E-Print Network [OSTI]

Bismuth±Ceramic Nanocomposites with Unusual Thermal Stability via High-Energy Ball Milling, nanostructured bismuth±ceramic nanocomposites with unusual thermal stabil- ity. These materials contain a high. Important for electrical and thermoelectric applications, the ceramic phase is electrically and thermally

Braun, Paul

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Gravity as the square of Yang-Mills: implications for N=8 Supergravity  

E-Print Network [OSTI]

The pure gravity Lagrangian can be written as the "square" of the pure Yang-Mills Lagrangian to second order in coupling constants. This paper uses this form of the gravity Lagrangian as a starting point to arrive at a compact light-cone superspace Lagrangian for N=8 Supergravity to order $\\kappa$^2.

Sudarshan Ananth

2009-02-18T23:59:59.000Z

402

Fine-grained Energy Consumption Characterization and Modeling Catherine Mills Olschanowsky, Tajana Rosing, and  

E-Print Network [OSTI]

Fine-grained Energy Consumption Characterization and Modeling Catherine Mills Olschanowsky, Tajana of the applications in the workload affect the energy consumption of the resource. Our experiments confirm that data the performance and energy-efficiency of candidate resources. Predicting the energy consumption of an HPC resource

Simunic, Tajana

403

Designing fecal pellet surveys for snowshoe hares K.E. Hodges *, L.S. Mills  

E-Print Network [OSTI]

Designing fecal pellet surveys for snowshoe hares K.E. Hodges *, L.S. Mills Wildlife Biology, 2003), some popular indices, like counts of fecal pellets, have been used to answer basic ecological pellets to examine long-term population dynamics at individual sites (Malloy, 2000; Krebs et al., 2001

Mills, L. Scott

404

Recycling of water in bleached kraft pulp mills by using electrodialysis.  

SciTech Connect (OSTI)

Conservation of water in bleached kraft pulp mills by recycling the bleach plant effluent directly without treatment will cause accumulation of inorganic ''non-process elements'' (NPEs) and serious operational problems. In this work, an electrodialysis process is being developed for recycling the acidic bleach plant effluent of bleached kraft pulp mills. In this process, electrodialysis functions as a selective kidney to remove inorganic NPEs from bleach plant effluents, before they reach the recovery cycle. Acidic bleach plant effluents from several mills using bleaching sequences based on chlorine dioxide were characterized. The total dissolved solids were mostly inorganic NPEs. Sodium was the predominant cation and chloride was present at significant levels in all these effluents. In laboratory electrodialysis experiments, selective removal of chloride and potentially harmful cations, such as potassium, calcium, and magnesium, were removed efficiently. Rejection of organic compounds was up to 98%. Electrodialysis was shown to be resistant to membrane fouling and scaling, in a 100-hour laboratory experiment. Based on a model mill with 1,000 ton/day pulp production, the economic analysis suggests that the energy cost of electrodialysis is less than $200/day, and the capital cost of the stack is about $500,000.

Fracaro, A. T.; Henry, M. P.; Pfromm, P.; Tsai, S.-P.

1999-01-15T23:59:59.000Z

405

Environmental control technology for mining and milling low-grade uranium resources  

SciTech Connect (OSTI)

This study examined the type and level of wastes that would be generated in the mining and milling of U/sub 3/O/sub 8/ from four potential domestic sources of uranium. The estimated costs of the technology to control these wastes to different degrees of stringency are presented.

Weakley, S.A.; Blahnik, D.E.; Long, L.W.; Bloomster, C.H.

1981-04-01T23:59:59.000Z

406

Radiological survey of the inactive uranium-mill tailings at Green River, Utah  

SciTech Connect (OSTI)

The uranium-mill tailings at Green River, Utah, are relatively low in /sup 226/Ra content and concentration (20 Ci and 140 pCi/g, respectively) because the mill was used to upgrade the uranium ore by separating the sand and slime fractions; most of the radium was transported along with the slimes to another mill site. Spread of tailings was observed in all directions, but near-background gamma exposure rates were reached at distances of 40 to 90 m from the edge of the pile. Water erosion of the tailings is evident and, since a significant fraction of the tailings pile lies in Brown's Wash, the potential exists for repetition of the loss of a large quantity of tailings such as occurred during a flood in 1959. In general, the level of surface contamination was low at this site, but some areas in the mill site, which were being used for nonuranium work, have gamma-ray exposure rates up to 143 ..mu..R/hr.

Haywood, F.F.; Christian, D.J.; Ellis, B.S.; Hubbard, H.M. Jr.; Lorenzo, D.; Shinpaugh, W.H.

1980-03-01T23:59:59.000Z

407

MIL-L-87177 and CLT:X-10 Lubricants Improve Electrical Connector Fretting Corrosion Behavior  

SciTech Connect (OSTI)

We have conducted a fretting research project using MIL-L-87177 and CLT: X-10 lubricants on Nano-miniature connectors. When they were fretted without lubricant, individual connectors first exceeded our 0.5 ohm failure criteria from 2,341 to 45,238 fretting cycles. With additional fretting, their contact resistance increased to more than 100,000 ohms. Unmodified MIL-L-87177 lubricant delayed the onset of first failure to between 430,000 and over 20,000,000 fretting cycles. MIL-L-87177 modified by addition of Teflon powder delayed first failure to beyond 5 million fretting cycles. Best results were obtained when Teflon was used and also when both the straight and modified lubricants were poured into and then out of the connector. CLT: X-10 lubricant delayed the onset of first failure to beyond 55 million cycles in one test where a failure was actually observed and to beyond 20 million cycles in another that was terminated without failure. CLT: X-10 recovered an unlubricated connector driven deeply into failure, with six failed pins recovering immediately and four more recovering during an additional 420 thousand fretting cycles. MIL-L-87177 was not able to recover a connector under similar conditions.

AUKLAND,NEIL R.; HANLON,JAMES T.

1999-10-12T23:59:59.000Z

408

2PI Effective Action and Evolution Equations of N = 4 super Yang-Mills  

E-Print Network [OSTI]

We employ nPI effective action techniques to study N = 4 super Yang-Mills, and write down the 2PI effective action of the theory. We also supply the evolution equations of two-point correlators within the theory.

Jelena Smolic; Milena Smolic

2012-12-07T23:59:59.000Z

409

Carbonation of alkaline paper mill waste to reduce CO2 greenhouse gas emissions into the atmosphere  

E-Print Network [OSTI]

Carbonation of alkaline paper mill waste to reduce CO2 greenhouse gas emissions into the atmosphere of anthropogenic emission of greenhouse gases into the atmosphere such as CO2, CH4, N2O and CFCs. The CO2 emissions to reflect, adsorb and emit the solar energy. However, the continuous emissions of CO2 into the atmosphere

Montes-Hernandez, German

410

Determination of HEat Capacity of Yucca Mountain Strtigraphic Layers  

SciTech Connect (OSTI)

The heat generated from the radioactive waste to be placed in the proposed geologic repository at Yucca Mountain, Nevada, will affect the thermal-hydrology of the Yucca Mountain stratigraphic layers. In order to assess the effect of the movement of repository heat into the fractured rocks accurate determination of thermodynamic and hydraulic properties is important. Heat capacity is one of the properties that are required to evaluate energy storage in the fractured rock. Rock-grain heat capacity, the subject of this study, is the heat capacity of the solid part of the rock. Yucca Mountain consists of alternating lithostratigraphic units of welded and non-welded ash-flow tuff, mainly rhyolitic in composition and displaying varying degrees of vitrification and alteration. A number of methods exist that can be used to evaluate heat capacity of the stratigraphic layers that consist of different compositions. In this study, the mineral summation method has been used to quantify the heat capacity of the stratigraphic layers based on Kopp's rule. The mineral summation method is an addition of the weighted heat capacity of each mineral found in a specific layer. For this study the weighting was done based on the mass percentage of each mineral in the layer. The method utilized a mineralogic map of the rocks at the Yucca Mountain repository site. The Calico Hills formation and adjacent bedded tuff layers display a bimodal mineral distribution of vitric and zeolitic zones with differing mineralogies. Based on this bimodal distribution in zeolite abundance, the boundary between the vitric and zeolitic zones was selected to be 15% zeolitic abundance. Thus, based on the zeolite abundance, subdivisions have been introduced to these layers into ''vitric'' and ''zeolitic'' zones. Heat capacity values have been calculated for these layers both as ''layer average'' and ''zone average''. The heat capacity determination method presented in this report did not account for spatial variability in the horizontal direction within each layer.

T. Hadgu; C. Lum; J.E. Bean

2006-06-20T23:59:59.000Z

411

GASCAP: Wellhead Gas Productive Capacity Model documentation, June 1993  

SciTech Connect (OSTI)

The Wellhead Gas Productive Capacity Model (GASCAP) has been developed by EIA to provide a historical analysis of the monthly productive capacity of natural gas at the wellhead and a projection of monthly capacity for 2 years into the future. The impact of drilling, oil and gas price assumptions, and demand on gas productive capacity are examined. Both gas-well gas and oil-well gas are included. Oil-well gas productive capacity is estimated separately and then combined with the gas-well gas productive capacity. This documentation report provides a general overview of the GASCAP Model, describes the underlying data base, provides technical descriptions of the component models, diagrams the system and subsystem flow, describes the equations, and provides definitions and sources of all variables used in the system. This documentation report is provided to enable users of EIA projections generated by GASCAP to understand the underlying procedures used and to replicate the models and solutions. This report should be of particular interest to those in the Congress, Federal and State agencies, industry, and the academic community, who are concerned with the future availability of natural gas.

Not Available

1993-07-01T23:59:59.000Z

412

Energy Efficiency Feasibility Study and Resulting Plan for the Bay Mills Indian Community  

SciTech Connect (OSTI)

In 2011 the Inter-Tribal Council of Michigan, Inc. was awarded an Energy Efficiency Development and Deployment in Indian Country grant from the U.S. Department of Energy’s Tribal Energy Program. This grant aimed to study select Bay Mills Indian Community community/government buildings to determine what is required to reduce each building’s energy consumption by 30%. The Bay Mills Indian Community (BMIC) buildings with the largest expected energy use were selected for this study and included the Bay Mills Ellen Marshall Health Center building, Bay Mills Indian Community Administration Building, Bay Mills Community College main campus, Bay Mills Charter School and the Waishkey Community Center buildings. These five sites are the largest energy consuming Community buildings and comprised the study area of this project titled “Energy Efficiency Feasibility Study and Resulting Plan for the Bay Mills Indian Community”. The end objective of this study, plan and the Tribe is to reduce the energy consumption at the Community’s most energy intensive buildings that will, in turn, reduce emissions at the source of energy production, reduce energy expenditures, create long lasting energy conscious practices and positively affect the quality of the natural environment. This project’s feasibility study and resulting plan is intended to act as a guide to the Community’s first step towards planned energy management within its buildings/facilities. It aims to reduce energy consumption by 30% or greater within the subject facilities with an emphasis on energy conservation and efficiency. The energy audits and related power consumption analyses conducted for this study revealed numerous significant energy conservation and efficiency opportunities for all of the subject sites/buildings. In addition, many of the energy conservation measures require no cost and serve to help balance other measures requiring capital investment. Reoccurring deficiencies relating to heating, cooling, thermostat setting inefficiencies, powering computers, lighting, items linked to weatherization and numerous other items were encountered that can be mitigated with the energy conservation measures developed and specified during the course of this project.

Kushman, Chris

2014-02-03T23:59:59.000Z

413

Means for limiting and ameliorating electrode shorting  

SciTech Connect (OSTI)

A fuse and filter arrangement for limiting and ameliorating electrode shorting in capacitive deionization water purification systems utilizing carbon aerogel, for example. This arrangement limits and ameliorates the effects of conducting particles or debonded carbon aerogel in shorting the electrodes of a system such as a capacitive deionization water purification system. This is important because of the small interelectrode spacing and the finite possibility of debonding or fragmentation of carbon aerogel in a large system. The fuse and filter arrangement electrically protect the entire system from shutting down if a single pair of electrodes is shorted and mechanically prevents a conducting particle from migrating through the electrode stack, shorting a series of electrode pairs in sequence. It also limits the amount of energy released in a shorting event. The arrangement consists of a set of circuit breakers or fuses with one fuse or breaker in the power line connected to one electrode of each electrode pair and a set of screens of filters in the water flow channels between each set of electrode pairs.

Van Konynenburg, Richard A. (Livermore, CA); Farmer, Joseph C. (Tracy, CA)

1999-01-01T23:59:59.000Z

414

Means for limiting and ameliorating electrode shorting  

SciTech Connect (OSTI)

A fuse and filter arrangement is described for limiting and ameliorating electrode shorting in capacitive deionization water purification systems utilizing carbon aerogel, for example. This arrangement limits and ameliorates the effects of conducting particles or debonded carbon aerogel in shorting the electrodes of a system such as a capacitive deionization water purification system. This is important because of the small interelectrode spacing and the finite possibility of debonding or fragmentation of carbon aerogel in a large system. The fuse and filter arrangement electrically protect the entire system from shutting down if a single pair of electrodes is shorted and mechanically prevents a conducting particle from migrating through the electrode stack, shorting a series of electrode pairs in sequence. It also limits the amount of energy released in a shorting event. The arrangement consists of a set of circuit breakers or fuses with one fuse or breaker in the power line connected to one electrode of each electrode pair and a set of screens of filters in the water flow channels between each set of electrode pairs.

Konynenburg, R.A. van; Farmer, J.C.

1999-11-09T23:59:59.000Z

415

Electricity storage for short term power system service (Smart...  

Open Energy Info (EERE)

Electricity storage for short term power system service (Smart Grid Project) Jump to: navigation, search Project Name Electricity storage for short term power system service...

416

Short Gamma-Ray Bursts Are Different  

E-Print Network [OSTI]

We analyze BATSE time-tagged event (TTE) data for short gamma-ray bursts (T90 duration burst. Performing the cross-correlation between two energy bands, we measure an average lag ~ 20-40 x shorter than for long bursts, and a lag distribution close to symmetric about zero - unlike long bursts. Using a "Bayesian Block" method to identify significantly distinct pulse peaks, we find an order of magnitude fewer pulses than found in studies of long bursts. The disparity in lag magnitude is discontinuous across the ~ 2-s valley between long and short bursts. Thus, short bursts do not appear to be representable as a continuation of long bursts' temporal characteristics.

J. P. Norris; J. D. Scargle; J. T. Bonnell

2001-05-07T23:59:59.000Z

417

Catalysts for synthesizing various short chain hydrocarbons  

DOE Patents [OSTI]

Method and apparatus (10), including novel photocatalysts, are disclosed for the synthesis of various short chain hydrocarbons. Light-transparent SiO.sub.2 aerogels doped with photochemically active uranyl ions (18) are fluidized in a fluidized-bed reactor (12) having a transparent window (16), by hydrogen and CO, C.sub.2 H.sub.4 or C.sub.2 H.sub.6 gas mixtures (20), and exposed to radiation (34) from a light source (32) external to the reactor (12), to produce the short chain hydrocarbons (36).

Colmenares, Carlos (Alamo, CA)

1991-01-01T23:59:59.000Z

418

Gasoline prices up this week (short version)  

Gasoline and Diesel Fuel Update (EIA)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"Click worksheet9,1,50022,3,,,,6,1,,781 2,328 2,683DieselValues shownshort version)short version)short

419

Evaluating point and process fugitive emission sources of particulate matter from feed mills associated with cattle feed yards  

E-Print Network [OSTI]

. 843 kg/m' (0. 0526 lb/ft') and 2688 m/min (8820 fpm), respectively. Since the dimensions of the rectangular exhaust duct were 27. 9x35. 6 cendmeters (I lx14 inches), the volume rate of flow of air handled by this cyclone was determined to be 267 m.... Emission factors for feed mills (Shannon et al. , 1974) Table 2. 1988 AP-42 emission factors for feed mills Table 3. Intemn AP-42 emission actors for grain elevators 12 Table 4. Proposed emission factors for feed mills 14 Table 5. Source sampling...

Demny, Michael Alan

2012-06-07T23:59:59.000Z

420

Determining the Capacity Value of Wind: An Updated Survey of Methods and Implementation; Preprint  

SciTech Connect (OSTI)

This paper summarizes state and regional studies examining the capacity value of wind energy, how different regions define and implement capacity reserve requirements, and how wind energy is defined as a capacity resource in those regions.

Milligan, M.; Porter, K.

2008-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Pipeline capacity trading could be more efficient if{hor_ellipsis}  

SciTech Connect (OSTI)

This paper discusses the efficiency of pipeline capacity trading. The characteristics of efficient markets, southwest U.S. capacity market, and a solution to excess capacity burden are discussed. It is concluded that capacity trading could be more efficient if the following were to occur: parity of capacity sales was achieved; timely reporting of EBBs of price, volume, and path was mandatory; rate caps on released capacity were removed; and market based rates are established for pipelines.

Roth, R.

1995-12-31T23:59:59.000Z

422

Cycle cover with short cycles Nicole Immorlica  

E-Print Network [OSTI]

Introduction Given a graph and a subset of marked elements (nodes, edges, or some combination thereof), a cycleCycle cover with short cycles Nicole Immorlica£ Mohammad Mahdian£ Vahab S. Mirrokni£ Abstract Cycle for variants of cycle covering problems which bound the size and/or length of the covering cycles

Immorlica, Nicole

423

Nucleon - Nucleon Interactions at Short Distances  

E-Print Network [OSTI]

Despite the progress made in understanding the NN interactions at long distances based on effective field theories, the understanding of the dynamics of short range NN interactions remains as elusive as ever. One of the most fascinating properties of short range interaction is its repulsive nature which is responsible for the stability of strongly interacting matter. The relevant distances, $\\le 0.5$ fm, in this case are such that one expects the onset of quark-gluon degrees of freedom with interaction being dominated by QCD dynamics. We review the current status of the understanding of the QCD dynamics of NN interactions at short distances, highlight outstanding questions and outline the theoretical foundation of QCD description of hard NN processes. We present examples of how the study of the hard elastic NN interaction can reveal the symmetry structure of valence quark component of the nucleon wave function and how the onset of pQCD regime is correlated with the onset of color transparency phenomena in hard $pp$ scattering in the nuclear medium. The discussions show how the new experimental facilities can help to advance the knowledge about the QCD nature of nuclear forces at short distances.

Misak M Sargsian

2014-03-04T23:59:59.000Z

424

SHORT REVIEW Ecological genomics: understanding gene and  

E-Print Network [OSTI]

SHORT REVIEW Ecological genomics: understanding gene and genome function in the natural environment MC Ungerer, LC Johnson and MA Herman Division of Biology, Ecological Genomics Institute, Kansas State University, Manhattan, KS, USA The field of ecological genomics seeks to understand the genetic mechanisms

Kaufman, Glennis A.

425

Short communication Sediment budget possibilities and improbabilities  

E-Print Network [OSTI]

Short communication Sediment budget possibilities and improbabilities Todd L. Walton Jr. a algebra Matrix algebra Sand Sediment bypassing Sediment budget Sediment management Waves Problems of constructing a sediment budget for an inlet is often a challenge due to constraints on data collection, quality

US Army Corps of Engineers

426

LE JOURNAL DE PHYSIQUE Short Communication  

E-Print Network [OSTI]

2307 LE JOURNAL DE PHYSIQUE Short Communication Cold fusion in a dense electron gas R. Balian, J in metallic palladiun are required in order to bring the cold fusion rate to an observable value. 'Ibme 50 N are known to yield observable rates for "cold fusion" in ddp-molecules [1-3]. One may also notice

Boyer, Edmond

427

SHORT CONTRIBUTION J. Choi S. Y. Lee  

E-Print Network [OSTI]

(3HB/V), several addi- tional factors need to be examined during process analysis and economic and methods Process analysis and economic evaluation of P(3HB/V) production and recovery were carried outSHORT CONTRIBUTION J. Choi á S. Y. Lee Economic considerations in the production of poly(3

428

Video Production For Short Educational Videos  

E-Print Network [OSTI]

Video Production Handbook For Short Educational Videos Jennifer Cook Small Acreage Management page 6 Introduction page 3 Prepare for Video Shoot page 8 Video Shoot page 9 Editing Page 11 Draft Review page 12 Final Video page 13 Table of Contents Video Production Process #12;3 Equipment

429

Short Specialist Review Gene structure prediction  

E-Print Network [OSTI]

Short Specialist Review Gene structure prediction in plant genomes Volker Brendel Iowa State) within most genes makes the problem of computational gene structure prediction distinct from (and harder prediction in vertebrates. The second reason is pragmatic. Expressed Sequence Tag (EST) sequencing and whole

Brendel, Volker

430

Student Groups Student Group Description Short Description  

E-Print Network [OSTI]

Student Groups Student Group Description Short Description AHR Scholar-Architecture Scholar ART Honors - Architecture Honors H04 Honors - Allied Medical Prof Honors H05 Honors - Arts & Sciences Honors H14 Honors - Envir&Natural Resources Honors H15 Honors - Food, Agr, & Envir Sci Honors H16 Honors

431

SHORT-RUN MONEY DEMAND Laurence Ball  

E-Print Network [OSTI]

SHORT-RUN MONEY DEMAND Laurence Ball Johns Hopkins University August 2002 I am grateful with Goldfeld's partial adjustment model. A key innovation is the choice of the interest rate in the money on "near monies" -- close substitutes for M1 such as savings accounts and money market mutual funds

Niebur, Ernst

432

Electricity and short wavelength radiation generator  

DOE Patents [OSTI]

Methods and associated apparati for use of collisions of high energy atoms and ions of He, Ne, or Ar with themselves or with high energy neutrons to produce short wavelength radiation (lambda approx. = 840-1300 A) that may be utilized to produce cathode-anode currents or photovoltaic currents.

George, E.V.

1985-08-26T23:59:59.000Z

433

E-Print Network 3.0 - aerobic exercise capacity Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

to the aerobic capacity of skeletal muscles (21, 25, 50). Histori- cally, a denser capillary... from animals adapted for high aerobic capacity, ... Source: Garland Jr.,...

434

E-Print Network 3.0 - airport capacity Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

; Energy Storage, Conversion and Utilization 2 AIRPORT TROUGHPUT CAPACITY LIMITS FOR DEMAND MANAGEMENT Vivek Kumar, Lance Sherry Summary: AIRPORT TROUGHPUT CAPACITY LIMITS FOR...

435

Nano-scale Composite Hetero-structures: Novel High Capacity Reversible...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Nano-scale Composite Hetero-structures: Novel High Capacity Reversible Anodes for Lithium-ion Batteries Nano-scale Composite Hetero-structures: Novel High Capacity Reversible...

436

HETEROGENEITY IN SHORT GAMMA-RAY BURSTS  

SciTech Connect (OSTI)

We analyze the Swift/BAT sample of short gamma-ray bursts, using an objective Bayesian Block procedure to extract temporal descriptors of the bursts' initial pulse complexes (IPCs). The sample is comprised of 12 and 41 bursts with and without extended emission (EE) components, respectively. IPCs of non-EE bursts are dominated by single pulse structures, while EE bursts tend to have two or more pulse structures. The medians of characteristic timescales-durations, pulse structure widths, and peak intervals-for EE bursts are factors of {approx}2-3 longer than for non-EE bursts. A trend previously reported by Hakkila and colleagues unifying long and short bursts-the anti-correlation of pulse intensity and width-continues in the two short burst groups, with non-EE bursts extending to more intense, narrower pulses. In addition, we find that preceding and succeeding pulse intensities are anti-correlated with pulse interval. We also examine the short burst X-ray afterglows as observed by the Swift/X-Ray Telescope (XRT). The median flux of the initial XRT detections for EE bursts ({approx}6x10{sup -10} erg cm{sup -2} s{sup -1}) is {approx}>20x brighter than for non-EE bursts, and the median X-ray afterglow duration for EE bursts ({approx}60,000 s) is {approx}30x longer than for non-EE bursts. The tendency for EE bursts toward longer prompt-emission timescales and higher initial X-ray afterglow fluxes implies larger energy injections powering the afterglows. The longer-lasting X-ray afterglows of EE bursts may suggest that a significant fraction explode into denser environments than non-EE bursts, or that the sometimes-dominant EE component efficiently powers the afterglow. Combined, these results favor different progenitors for EE and non-EE short bursts.

Norris, Jay P. [Physics and Astronomy Department, University of Denver, Denver, CO 80208 (United States); Gehrels, Neil [Astroparticle Physics Laboratory, NASA/Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Scargle, Jeffrey D. [Space Science and Astrobiology Division, NASA/Ames Research Center, Moffett Field, CA 94035-1000 (United States)

2011-07-01T23:59:59.000Z

437

Plug and Process Loads Capacity and Power Requirements Analysis  

SciTech Connect (OSTI)

This report addresses gaps in actionable knowledge that would help reduce the plug load capacities designed into buildings. Prospective building occupants and real estate brokers lack accurate references for plug and process load (PPL) capacity requirements, so they often request 5-10 W/ft2 in their lease agreements. Limited initial data, however, suggest that actual PPL densities in leased buildings are substantially lower. Overestimating PPL capacity leads designers to oversize electrical infrastructure and cooling systems. Better guidance will enable improved sizing and design of these systems, decrease upfront capital costs, and allow systems to operate more energy efficiently. The main focus of this report is to provide industry with reliable, objective third-party guidance to address the information gap in typical PPL densities for commercial building tenants. This could drive changes in negotiations about PPL energy demands.

Sheppy, M.; Gentile-Polese, L.

2014-09-01T23:59:59.000Z

438

A stochastic multiscale model for electricity generation capacity ...  

E-Print Network [OSTI]

mand response requires a coupling of both the long and short term dynamics. ... Division, Massachusetts Institute of Technology, 77 Massachusetts Ave, Building ... or demand elasticity (a major objective of demand response programs).

2011-04-21T23:59:59.000Z

439

Advanced Mitigating Measures for the Cell Internal Short Risk (Presentation)  

SciTech Connect (OSTI)

This presentation describes mitigation measures for internal short circuits in lithium-ion battery cells.

Darcy, E.; Smith, K.

2010-04-01T23:59:59.000Z

440

Undecidability of the Spectral Gap (short version)  

E-Print Network [OSTI]

The spectral gap -- the difference in energy between the ground state and the first excited state -- is one of the most important properties of a quantum many-body system. Quantum phase transitions occur when the spectral gap vanishes and the system becomes critical. Much of physics is concerned with understanding the phase diagrams of quantum systems, and some of the most challenging and long-standing open problems in theoretical physics concern the spectral gap, such as the Haldane conjecture that the Heisenberg chain is gapped for integer spin, proving existence of a gapped topological spin liquid phase, or the Yang-Mills gap conjecture (one of the Millennium Prize problems). These problems are all particular cases of the general spectral gap problem: Given a quantum many-body Hamiltonian, is the system it describes gapped or gapless? Here we show that this problem is undecidable, in the same sense as the Halting Problem was proven to be undecidable by Turing. A consequence of this is that the spectral gap...

Cubitt, Toby; Wolf, Michael M

2015-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Undecidability of the Spectral Gap (short version)  

E-Print Network [OSTI]

The spectral gap -- the difference in energy between the ground state and the first excited state -- is one of the most important properties of a quantum many-body system. Quantum phase transitions occur when the spectral gap vanishes and the system becomes critical. Much of physics is concerned with understanding the phase diagrams of quantum systems, and some of the most challenging and long-standing open problems in theoretical physics concern the spectral gap, such as the Haldane conjecture that the Heisenberg chain is gapped for integer spin, proving existence of a gapped topological spin liquid phase, or the Yang-Mills gap conjecture (one of the Millennium Prize problems). These problems are all particular cases of the general spectral gap problem: Given a quantum many-body Hamiltonian, is the system it describes gapped or gapless? Here we show that this problem is undecidable, in the same sense as the Halting Problem was proven to be undecidable by Turing. A consequence of this is that the spectral gap of certain quantum many-body Hamiltonians is not determined by the axioms of mathematics, much as Goedels incompleteness theorem implies that certain theorems are mathematically unprovable. We extend these results to prove undecidability of other low temperature properties, such as correlation functions. The proof hinges on simple quantum many-body models that exhibit highly unusual physics in the thermodynamic limit.

Toby Cubitt; David Perez-Garcia; Michael M. Wolf

2015-02-13T23:59:59.000Z

442

Proceedings of NAMRI/SME, Vol. 40, 2012 PVD Coated Mill Rolls for Cold Rolling of Stainless Steel  

E-Print Network [OSTI]

Proceedings of NAMRI/SME, Vol. 40, 2012 PVD Coated Mill Rolls for Cold Rolling of Stainless Steel : United States (2012)" #12;Proceedings of NAMRI/SME, Vol. 40, 2012 again affecting both friction

Paris-Sud XI, Université de

443

Radionuclides in the terrestrial ecosystem near a Canadian uranium mill -- Part 2: Small mammal food chains and bioavailability  

SciTech Connect (OSTI)

Food chain transfer through the soil-vegetation-small mammal food chain was measured by concentration ratios (CRs) for uranium, {sup 226}Ra, {sup 210}Pb, and {sup 210}Po at three sites near the Key Lake uranium mill in northern Saskatchewan. Plant/soil CRs, animal carcass/GI tract CRs, and animal/soil CRs were depressed at sites impacted by mill and tailings dusts relative to a nearby control site. Thus, radionuclides associated with large particulates in tailings and/or ore dusts may be less bioavailable to terrestrial plants and animals than natural sources of radioactive dust. These results show that reliance on default food chain transfer parameters, obtained from uncontaminated terrestrial ecosystems, may overpredict impacts at uranium mine and mill sites. Given the omnivorous diet of small mammals and birds, animal/soil CRs are recommended as the most cost-effective and robust means of predicting animal concentrations from environmental monitoring data at uranium mill facilities.

Thomas, P.A.

2000-06-01T23:59:59.000Z

444

Method of increasing the sulfation capacity of alkaline earth sorbents  

DOE Patents [OSTI]

A system and method for increasing the sulfation capacity of alkaline earth carbonates to scrub sulfur dioxide produced during the fluidized bed combustion of coal in which partially sulfated alkaline earth carbonates are hydrated in a fluidized bed to crack the sulfate coating and convert the alkaline earth oxide to the hydroxide. Subsequent dehydration of the sulfate-hydroxide to a sulfate-oxide particle produces particles having larger pore size, increased porosity, decreased grain size and additional sulfation capacity. A continuous process is disclosed.

Shearer, J.A.; Turner, C.B.; Johnson, I.

1980-03-13T23:59:59.000Z

445

On the Capacity of a Class of MIMO Cognitive Radios  

E-Print Network [OSTI]

Cognitive radios have been studied recently as a means to utilize spectrum in a more efficient manner. This paper focuses on the fundamental limits of operation of a MIMO cognitive radio network with a single licensed user and a single cognitive user. The channel setting is equivalent to an interference channel with degraded message sets (with the cognitive user having access to the licensed user's message). An achievable region and an outer bound is derived for such a network setting. It is shown that the achievable region is optimal for a portion of the capacity region that includes sum capacity.

Sridharan, Sriram

2007-01-01T23:59:59.000Z

446

Baseline risk assessment of ground water contamination at the Uranium Mill Tailings Site near Green River, Utah  

SciTech Connect (OSTI)

This document evaluates potential impacts to public health and the environment resulting from ground water contamination at the former uranium mill processing site. The tailings and other contaminated material at this site were placed in a disposal cell on the site in 1989 by the US DOE`s Uranium Mill Tailings Remedial Action (UMTRA) Project. Currently, UMTRA Project is evaluating ground water contamination in this risk assessment.

Not Available

1994-09-01T23:59:59.000Z

447

Remedial action plan and site design for stabilization of the inactive uranium mill tailings sites at Rifle, Colorado  

SciTech Connect (OSTI)

This appendix assesses the present conditions and data gathered about the two inactive uranium mill tailings sites near Rifle, Colorado, and the designated disposal site six miles north of Rifle in the area of Estes Gulch. It consolidates available engineering, radiological, geotechnical, hydrological, meteorological, and other information pertinent to the design of the Remedial Action Plan (RAP). The data characterize conditions at the mill, tailings, and disposal site so that the Remedial Action Contractor (RAC) may complete final designs for the remedial actions.

Not Available

1992-02-01T23:59:59.000Z

448

Asphalt emulsion radon barrier systems for uranium mill tailings: an overview of the technology  

SciTech Connect (OSTI)

Pacific Northwest Laboratory (PNL), under contract to the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project (UMTRAP) office, has developed an asphalt emulsion cover system to reduce the release of radon from uranium mill tailings. The system has been field tested at Grand Junction, Colorado. Results from laboratory and field tests indicate that this system is effective in reducing radon release to near-background levels (<2.5 pCi m/sup -2/s/sup -1/) and has the properties required for long-term effectiveness and stability. Engineering specifications have been developed, and analysis indicates that asphalt emulsion covers are cost-competitive with other cover systems. This report summarizes the technology for asphalt emulsion radon barrier systems. 59 references, 45 figures, 36 tables.

Baker, E.G.; Hartley, J.N.; Freeman, H.D.; Gates, T.E.; Nelson, D.A.; Dunning, R.L.

1984-03-01T23:59:59.000Z

449

Study of Yang–Mills–Chern–Simons theory in presence of the Gribov horizon  

SciTech Connect (OSTI)

The two-point gauge correlation function in Yang–Mills–Chern–Simons theory in three dimensional Euclidean space is analysed by taking into account the non-perturbative effects of the Gribov horizon. In this way, we are able to describe the confinement and de-confinement regimes, which naturally depend on the topological mass and on the gauge coupling constant of the theory. -- Highlights: •We implement the Gribov quantization to the Topologically massive Yang–Mills theory. •We find a modified propagator at strong coupling by the Gribov horizon. •The gauge propagator depends on the topological mass and the coupling constant. •By studying the gauge propagator we describe the confined–deconfined regimes.

Canfora, Fabrizio, E-mail: canfora@cecs.cl [Centro de Estudios Cientificos (CECs), Valdivia (Chile); Universidad Andres Bello, Av. Republica 440, Santiago (Chile); Gomez, Arturo, E-mail: arturo.gomez@proyectos.uai.cl [Departamento de Ciencias, Facultad de Artes Liberales y Facultad de Ingeniería y Ciencias, Universidad Adolfo Ibáñez, Viña del Mar. (Chile); Sorella, Silvio Paolo, E-mail: sorella@uerj.br [UERJ, Universidade do Estado do Rio de Janeiro (UERJ), Instituto de Física Teórica, Rua São Francisco Xavier 524, 20550-013, Maracaná, Rio de Janeiro (Brazil); Vercauteren, David, E-mail: vercauteren.uerj@gmail.com [UERJ, Universidade do Estado do Rio de Janeiro (UERJ), Instituto de Física Teórica, Rua São Francisco Xavier 524, 20550-013, Maracaná, Rio de Janeiro (Brazil)

2014-06-15T23:59:59.000Z

450

Estimated dose to man from uranium milling via the terrestrial food-chain pathway  

SciTech Connect (OSTI)

One of the major pathways of radiological exposure to man from uranium milling operations is through the terrestrial food chain. Studies by various investigators have shown the extent of uptake and distribution of U-238, U-234, Th-230, Ra-226, Pb-210, and Po-210 in plants and animals. These long-lived natural radioisotopes, all nuclides of the uranium decay series, are found in concentrated amounts in uranium mill tailings. Data from these investigations are used to estimate the dose to man from consumption of beef and milk contaminated by the tailings. This dose estimate from this technologically enhanced source is compared with that from average normal dietary intake of these radionuclides from natural sources.

Rayno, D.R.

1982-01-01T23:59:59.000Z

451

EIS-0355: Remediation of the Moab Uranium Mill Tailings, Grand and San Juan Counties, Utah  

Broader source: Energy.gov [DOE]

The Remediation of the Moab Uranium Mill Tailings, Grand and San Juan Counties, Utah, Environmental Impact Statement and associated supplements and amendments provides information on the environmental impacts of the U.S. Department of Energy’s (DOE’s) proposal to (1) remediate approximately 11.9 million tons of contaminated materials located on the Moab site and approximately 39,700 tons located on nearby vicinity properties and (2) develop and implement a ground water compliance strategy for the Moab site using the framework of the Programmatic Environmental Impact Statement for the Uranium Mill Tailings Remedial Action Ground Water Project (DOE/EIS-0198, October 1996). The surface remediation alternatives analyzed in the EIS include on-site disposal of the contaminated materials and off-site disposal at one of three alternative locations in Utah using one or more transportation options: truck, rail, or slurry pipeline.

452

Finding of No Significant Impact, proposed remediation of the Maybell Uranium Mill Processing Site, Maybell, Colorado  

SciTech Connect (OSTI)

The U.S. Department of Energy (DOE) has prepared an environmental assessment (EA) (DOE/EA-0347) on the proposed surface remediation of the Maybell uranium mill processing site in Moffat County, Colorado. The mill site contains radioactively contaminated materials from processing uranium ore that would be stabilized in place at the existing tailings pile location. Based on the analysis in the EA, DOE has determined that the proposed action does not constitute a major federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969, Public Law 91-190 (42 U.S.C. {section}4321 et seq.), as amended. Therefore, preparation of an environmental impact statement is not required and DOE is issuing this Finding of No Significant Impact (FONSI).

Not Available

1995-12-31T23:59:59.000Z

453

Baseline risk assessment of ground water contamination at the Uranium Mill Tailings Site near Riverton, Wyoming  

SciTech Connect (OSTI)

This Risk Assessment evaluated potential impacts to public health or the environment caused by ground water contamination at the former uranium mill processing site. In the first phase of the U.S. Department of Energy`s Uranium Mill Tailings Remedial Action (UMTRA) Project, the tailing and other contaminated material at this site were placed in a disposal cell near the Gas Hills Plant in 1990. The second phase of the UMTRA Project is to evaluate ground water contamination. This risk assessment is the first site-specific document to evaluate potential health and environmental risks for the Riverton site under the Ground Water Project; it will help determine whether remedial actions are needed for contaminated ground water at the site.

Not Available

1994-09-01T23:59:59.000Z

454

Uranium mining and milling sites remediation by COGEMA impact on the environment  

SciTech Connect (OSTI)

Mining and milling of any metal have a common impact on the environment. Because of radioactivity uranium ores and their residues generate specific potential hazards. First we quote the french regulation as regards to radioactive impact through the different pathways. Then we overview the different types of uranium mining wastes and the type of storage for milling residues; Objectives being set for the remediation we describe basic principles of the methodology and give a few examples from France and the US Monitoring goes on all through the active period of the site and is fitted to it after its remediation. To date, according to the measurements done in the environment, the added radiological impact is equivalent to the natural background.

Daroussin, J.L.; Pfiffelmann, J.P. [COGEMA, Velizy (France)

1994-12-31T23:59:59.000Z

455

Revegetation and rock cover for stabilization of inactive uranium mill tailings disposal sites. Final report  

SciTech Connect (OSTI)

Guidelines for using vegetation and rock to protect inactive uranium mill tailings from erosion were developed by Pacific Northwest Laboratory as part of the Department of Energy's Uranium Mill Tailings Remedial Action Project (UMTRAP) Technology Development program. Information on soils, climate, and vegetation were collected for 20 inactive tailings sites in the western United States. Sites were grouped according to similarities in climate and vegetation. Soil loss for those sites was characterized using the Universal Soil Loss Equation. Test plots were used to evaluate (1) the interaction between vegetation and sealant barrier systems and (2) the effects of surface rock on soil water and vegetation. Lysimeter and simulation studies were used to direct and support field experiments. 49 references, 17 figures, 16 tables.

Beedlow, P.A.

1984-05-01T23:59:59.000Z

456

Magnetic monopole and confinement/deconfinement phase transition in SU(3) Yang-Mills theory  

E-Print Network [OSTI]

We have proposed the non-Abelian dual superconductivity in SU(3) Yang-Mills theory for the mechanism of quark confinement,and we presented the numerical evidences in preceding lattice conferences by using the proposed gauge link decomposition to extract magnetic monopole in the gauge invariant way. In this talk, we focus on the dual Meissner effects in view of the magnetic monopole in SU(3) Yang-Mills theory. We measure the chromoelectric and chromomagnetic flux due to a pair of quark and antiquark source at finite temperature. Then, we measure the correlation function of Polyakov loops and Polyakov loop average at various temperatures, and investigate chromomagnetic monopole current induced by chromo-magnetic flux in both confinement and deconfinement phase. We will discuss the role of the chromoelectric monopole in confinement/deconfinement phase transition.

Akihiro Shibata; Kei-Ichi Kondo; Seikou Kato; Toru Shinohara

2015-01-26T23:59:59.000Z

457

Effective Polyakov-loop theory for pure Yang-Mills from strong coupling expansion  

E-Print Network [OSTI]

Lattice Yang-Mills theories at finite temperature can be mapped onto effective 3d spin systems, thus facilitating their numerical investigation. Using strong-coupling expansions we derive effective actions for Polyakov loops in the $SU(2)$ and $SU(3)$ cases and investigate the effect of higher order corrections. Once a formulation is obtained which allows for Monte Carlo analysis, the nature of the phase transition in both classes of models is investigated numerically, and the results are then used to predict -- with an accuracy within a few percent -- the deconfinement point in the original 4d Yang-Mills pure gauge theories, for a series of values of $N_\\tau$ at once.

Jens Langelage; Stefano Lottini; Owe Philipsen

2010-10-30T23:59:59.000Z

458

Dual Superconductor Picture for Strongly-coupled SU(2) Yang-Mills Theory  

E-Print Network [OSTI]

A new framework that fulfills the dual superconductor picture is proposed for the strongly-coupled Yang-Mills theory. This framework is based on the idea that at the classic level the strong-coupling limit of the theory vacuum behaves as a back hole with regard to colors in the sense of the effective field theory, and the theory variables undergo an ultraviolet/infrared scale separation. We show that at the quantum level the strong-coupled theory vacuum is made up of a Bose-condensed many-body system of magnetic charges. We further check this framework by reproducing the dual Abelian-Higgs model from the Yang-Mills theory and the predicting the vacuum type of the theory which is very near to the border between type-I and type-II superconductors and remarkably consistent with the recent simulations.

Duoje Jia; Yi-shi Duan

2006-05-18T23:59:59.000Z

459

The infrared fixed point of Landau gauge Yang-Mills theory: A renormalization group analysis  

E-Print Network [OSTI]

The infrared behavior of gluon and ghost propagators in Landau gauge Yang-Mills theory has been at the center of an intense debate over the last decade. Different solutions of the Dyson-Schwinger equations show a different behavior of the propagators in the infrared: in the so-called scaling solutions both propagators follow a power law, while in the decoupling solutions the gluon propagator shows a massive behavior. The latest lattice results favor the decoupling solutions. In this contribution, after giving a brief overview of the present status of analytical and semi-analytical approaches to the infrared regime of Landau gauge Yang-Mills theory, we will show how Callan-Symanzik renormalization group equations in an epsilon expansion reproduce both types of solutions and single out the decoupling solutions as the infrared-stable ones for space-time dimensions greater than two, in agreement with the lattice calculations.

Axel Weber

2012-05-02T23:59:59.000Z

460

Infrared Behavior of 3-Point Functions in Landau Gauge Yang-Mills Theory  

E-Print Network [OSTI]

The three-gluon and ghost-gluon vertices of Landau gauge Yang-Mills theory are investigated in the low momentum regime. Due to ghost dominance in the infrared we can use the known power law behavior for the propagators to determine analytically the complete momentum dependence of the dressing functions. Besides a uniform, i. e. all momenta going to zero, divergence, we find additional singularities, if one momentum alone goes to zero, while the other two remain constant. At these asymmetric points we can extract additional infrared exponents, which corroborate previous results and expand the known fixed point solution of Landau gauge Yang-Mills theory, where the uniform infrared exponents for all vertex functions are known. Calculations in two and three dimensions yield qualitatively similar results.

Markus Q. Huber; Reinhard Alkofer; Kai Schwenzer

2008-12-23T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Infrared Behaviour of Landau Gauge Yang-Mills Theory with a Fundamentally Charged Scalar Field  

E-Print Network [OSTI]

The infrared behaviour of the n-point functions of a Yang-Mills theory with a charged scalar field in the fundamental representation of SU(N) is studied in the formalism of Dyson-Schwinger equations. Assuming a stable skeleton expansion solutions in form of power laws for the Green functions are obtained. For a massless scalar field the uniform limit is sufficient to describe the infrared scaling behaviour of vertices. Not taking into account a possible Higgs-phase it turns out that kinematic singularities play an important role for the scaling solutions of massive scalars. On a qualitative level scalar Yang-Mills theory yields similar scaling solutions as recently obtained for QCD.

Leonard Fister

2010-02-08T23:59:59.000Z

462

Manifestations of magnetic vortices in equation of state of Yang-Mills plasma  

E-Print Network [OSTI]

The vacuum of Yang-Mills theory contains singular stringlike objects identified with center (magnetic) vortices. Percolation of magnetic vortices is known to be responsible for the color confinement in the low-temperature phase of the theory. In our work we study properties of the vortices at finite temperature using lattice simulations of SU(2) gauge theory. We show that magnetic vortices provide a numerically large contribution to thermodynamic quantities of the gluon plasma in Yang-Mills theory. In particular, we observe that in the deconfinement phase at temperatures T_c energy-momentum tensor. In the confinement phase the vortex contribution is positive. The thermodynamical significance of the magnetic objects allows us to suggest that the quark-gluon plasma may contain a developed network of magnetic flux tubes. The existence of the vortex network may lead to observable effects in the quark-gluon plasma because the chromomagnetic field of the vortices should scatter and drag quarks.

M. N. Chernodub; Atsushi Nakamura; V. I. Zakharov

2008-07-31T23:59:59.000Z

463

Manifestations of magnetic vortices in equation of state of Yang-Mills plasma  

E-Print Network [OSTI]

The vacuum of Yang-Mills theory contains singular stringlike objects identified with center (magnetic) vortices. The percolation of the magnetic vortices is known to be responsible for the color confinement in the low-temperature phase of the theory. In our work we study properties of the vortices at finite temperature using lattice simulations of SU(2) gauge theory. We show that magnetic vortices provide numerically large contribution to thermodynamic quantities of gluon plasma in Yang-Mills theory. In particular, we observe that in the deconfinement phase at temperatures Tc energy-momentum tensor. In the confinement phase the vortex contribution is positive. The thermodynamical significance of the magnetic objects allows us to suggest that the quark gluon plasma may contain a developed network of the magnetic flux tubes. The existence of the vortex network may lead to observable eff...

Chernodub, M N; Zakharov, V I

2008-01-01T23:59:59.000Z

464

Remedial Action Plan and site design for stabilization of the inactive uranium mill tailings site at Falls City, Texas. [Uranium Mill Tailings Remedial Action (UMTRA) Project  

SciTech Connect (OSTI)

The uranium processing site near Falls City, Texas, was one of 24 inactive uranium mill sites designated to be remediated by the US Department of Energy (DOE) under Title I of the Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA). The UMTRCA requires that the US Nuclear Regulatory Commission (NRC) concur with the DOE's remedial action plan (RAP) and certify that the remedial action conducted at the site complies with the standards promulgated by the US Environmental Protection Agency (EPA). The RAP, which includes this summary remedial action selection report (RAS), serves a two-fold purpose. First, it describes the activities proposed by the DOE to accomplish long-term stabilization and control of the residual radioactive materials at the inactive uranium processing site near Falls City, Texas. Second, this document and the remainder of the RAP, upon concurrence and execution by the DOE, the State of Texas, and the NRC, becomes Appendix B of the Cooperative Agreement between the DOE and the State of Texas.

Chernoff, A.R. (USDOE Albuquerque Field Office, NM (United States). Uranium Mill Tailings Remedial Action Project Office); Lacker, D.K. (Texas State Dept. of Health, Austin, TX (United States). Bureau of Radiation Control)

1992-09-01T23:59:59.000Z

465

Effects Of Milling On Surface Integrity Of Low-Carbon Steel  

SciTech Connect (OSTI)

This work measured the effect of milling parameters on the surface integrity of low-carbon alloy steel. The Variance Analysis showed that only depth of cut did not influence on the workpiece roughness and the Pearson's Coefficient indicated that cutting speed was more influent than tool feed. All cutting parameters introduced tensile residual stress in workpiece surface. The chip formation mechanism depended specially on cutting speed and influenced on the roughness and residual stress of workpiece.

Rodrigues, Alessandro Roger; Matsumoto, Hidekasu; Yamakami, Wyser Jose; Tokimatsu, Ruis Camargo; Menezes, Miguel Angelo; Suyama, Daniel Iwao; Norcino, Adriana Bruno; Vendrame, Saimon [UNESP-Univ Estatual Paulista, Engineering Faculty of Ilha Solteira, Av. Brasil Centro, 56-Zip Code 15.385-000-Ilha Solteira, Sao Paulo (Brazil)

2011-01-17T23:59:59.000Z

466

Uranium Mill Tailings remedial action project waste minimization and pollution prevention awareness program plan  

SciTech Connect (OSTI)

The purpose of this plan is to establish a waste minimization and pollution prevention awareness (WM/PPA) program for the U.S. Department of Energy`s (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. The program satisfies DOE requirements mandated by DOE Order 5400.1. This plan establishes planning objectives and strategies for conserving resources and reducing the quantity and toxicity of wastes and other environmental releases.

Not Available

1994-07-01T23:59:59.000Z

467

Environmental assessment of ground-water compliance activities at the Uranium Mill Tailings Site, Spook, Wyoming  

SciTech Connect (OSTI)

This report assesses the environmental impacts of the Uranium Mill Tailings Site at Spook, Wyoming on ground water. DOE previously characterized the site and monitoring data were collected during the surface remediation. The ground water compliance strategy is to perform no further remediation at the site since the ground water in the aquifer is neither a current nor potential source of drinking water. Under the no-action alternative, certain regulatory requirements would not be met.

NONE

1997-02-01T23:59:59.000Z

468

Topologically massive Yang-Mills: A Hamilton-Jacobi constraint analysis  

SciTech Connect (OSTI)

We analyse the constraint structure of the topologically massive Yang-Mills theory in instant-form and null-plane dynamics via the Hamilton-Jacobi formalism. The complete set of hamiltonians that generates the dynamics of the system is obtained from the Frobenius’ integrability conditions, as well as its characteristic equations. As generators of canonical transformations, the hamiltonians are naturally linked to the generator of Lagrangian gauge transformations.

Bertin, M. C., E-mail: mcbertin@gmail.com [Instituto de Física, Universidade Federal da Bahia. Campus Universitário de Ondina, CEP 40210-340, Salvador, BA (Brazil); Pimentel, B. M., E-mail: pimentel@ift.unesp.br [Instituto de Física Teórica, UNESP - São Paulo State University. Caixa Postal 70532-2, 01156-970, São Paulo, SP (Brazil); Valcárcel, C. E., E-mail: carlos.valcarcel@ufabc.edu.br [CMCC, Universidade Federal do ABC. Rua Santa Adélia, 166, Santo André, SP (Brazil); Zambrano, G. E. R., E-mail: gramos@udenar.edu.co [Departamento de Física, Universidad de Nariño. Calle 18 Cra 50, San Juan de Pasto, Nariño (Colombia)] [Departamento de Física, Universidad de Nariño. Calle 18 Cra 50, San Juan de Pasto, Nariño (Colombia)

2014-04-15T23:59:59.000Z

469

Infrared Safe Observables in ${\\cal N}=4$ Super Yang-Mills Theory  

E-Print Network [OSTI]

The infrared structure of MHV gluon amplitudes in ${\\cal N}=4$ super Yang-Mills theory is considered in the next-to-leading order of PT. Explicit cancelation of the infrared divergencies in properly defined cross-sections is demonstrated. The remaining finite parts for some inclusive differential cross-sections are calculated analytically. In general, contrary to the virtual corrections, they do not reveal any simple structure.

L. V. Bork; D. I. Kazakov; G. S. Vartanov; A. V. Zhiboedov

2009-10-27T23:59:59.000Z

470

A covariant variational approach to Yang-Mills Theory at finite temperatures  

E-Print Network [OSTI]

We extend the covariant variational approach for SU(N) Yang-Mills theory in Landau gauge to non-zero temperatures. The renormalization of the zero-temperature case is revisited and it is shown that the same counterterms are sufficient to render the low-order Green's function finite at non-zero temperature. We compute the ghost and gluon propagator numerically and show that it agrees in all qualitative respects with the results of high-precision lattice calculations.

Markus Quandt; Hugo Reinhardt

2015-03-24T23:59:59.000Z

471

Scattering Equations and Matrices: From Einstein To Yang-Mills, DBI and NLSM  

E-Print Network [OSTI]

The tree-level S-matrix of Einstein's theory is known to have a representation as an integral over the moduli space of punctured spheres localized to the solutions of the scattering equations. In this paper we introduce three operations that can be applied on the integrand in order to produce other theories. Starting in $d+M$ dimensions we use dimensional reduction to construct Einstein-Maxwell with gauge group $U(1)^M$. The second operation turns gravitons into gluons and we call it "squeezing". This gives rise to a formula for all multi-trace mixed amplitudes in Einstein-Yang-Mills. Dimensionally reducing Yang-Mills we find the S-matrix of a special Yang-Mills-Scalar (YMS) theory, and by the squeezing operation we find that of a YMS theory with an additional cubic scalar vertex. A corollary of the YMS formula gives one for a single massless scalar with a $\\phi^4$ interaction. Starting again from Einstein's theory but in $d+d$ dimensions we introduce a "generalized dimensional reduction" that produces the Born-Infeld theory or a special Galileon theory in $d$ dimensions depending on how it is applied. An extension of Born-Infeld formula leads to one for the Dirac-Born-Infeld (DBI) theory. By applying the same operation to Yang-Mills we obtain the $U(N)$ non-linear sigma model (NLSM). Finally, we show how the Kawai-Lewellen-Tye relations naturally follow from our formulation and provide additional connections among these theories. One such relation constructs DBI from YMS and NLSM.

Freddy Cachazo; Song He; Ellis Ye Yuan

2015-01-25T23:59:59.000Z

472

The impact of sheared vs. sawn timber in the typical southern pine plywood mill  

E-Print Network [OSTI]

THE IMPACT OF SHEARED VS' SAWN TIMBER IN THE TYPICAL SOUTHERN PINE PLYWOOD MILL A Thesis by RUSSELL GARRETT SWINNEY Submitted to the Office of Graduate Studies of Texas ASM University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE December 1989 Major Subject: Forestry THE IMPACT OP SHEARED VS. SAWN T1MBER IN THE TYPICAL SOUTHERN PINE PLYWOOD MILI A Thesis by RUSSELL GARRETT SWINNEY Approved as to style and content by: Jease ( hair of mmi Jy...

Swinney, Russell Garrett

1989-01-01T23:59:59.000Z

473

Subcritical solution of the Yang-Mills Schroedinger equation in the Coulomb gauge  

E-Print Network [OSTI]

In the Hamiltonian approach to Coulomb gauge Yang-Mills theory, the functional Schroedinger equation is solved variationally resulting in a set of coupled Dyson-Schwinger equations. These equations are solved self-consistently in the subcritical regime defined by infrared finite form factors. It is shown that the Dyson-Schwinger equation for the Coulomb form factor fails to have a solution in the critical regime where all form factors have infrared divergent power laws.

D. Epple; H. Reinhardt; W. Schleifenbaum; A. P. Szczepaniak

2007-12-21T23:59:59.000Z

474

Subcritical solution of the Yang-Mills Schroedinger equation in the Coulomb gauge  

SciTech Connect (OSTI)

In the Hamiltonian approach to Coulomb gauge Yang-Mills theory, the functional Schroedinger equation is solved variationally resulting in a set of coupled Dyson-Schwinger equations. These equations are solved self-consistently in the subcritical regime defined by infrared-finite form factors. It is shown that the Dyson-Schwinger equation for the Coulomb form factor fails to have a solution in the critical regime where all form factors have infrared divergent power laws.

Epple, D.; Reinhardt, H.; Schleifenbaum, W.; Szczepaniak, A. P. [Institut fuer Theoretische Physik, Tuebingen University, Auf der Morgenstelle 14 D-72076 Tuebingen (Germany); Physics Department and Nuclear Theory Center Indiana University, Bloomington, Indiana 47405 (United States)

2008-04-15T23:59:59.000Z

475

A study of the effect of variable speed machining on regenerative chatter in end milling  

E-Print Network [OSTI]

and format of the ASME Journal of Manufacturing Science and Engineering. However it has been observed that the increase in MRR is not usually limited by the power of the machine tool but by the onset of severe vibrations, namely chatter (Taylor, 1907...), Sridar (1968), Fu (1984), Minis (1990), Altintas (1995), and others. These investigators have attributed the source of this self-excited vibration to the regeneration of waviness on the workpiece. Figure 3 illustrates the regeneration effect m milling...

Dhayalan, Arun Kumar

2000-01-01T23:59:59.000Z

476

Radiation in Yang-Mills formulation of gravity and a generalized pp-wave metric  

E-Print Network [OSTI]

The variational methods implemented on a quadratic Yang-Mills type Lagrangian yield two sets of equations interpreted as the field equations and the energy-momentum tensor for the gravitational field. A covariant condition is imposed on the energy-momentum tensor to represent the radiation field. A generalized pp-wave metric is found to simultaneously satisfy both the field equations and the radiation condition. The result is compared with that of Lichn\\'{e}rowicz.

S. Baskal

1997-12-23T23:59:59.000Z

477

Soil-site relationships for natural stands of longleaf pine (Pinus palustris Mill.) in east Texas  

E-Print Network [OSTI]

. Sites were characterized by so11 physical properties and physiographic factors. Correlation of longleaf site index and height growth with site factors was evaluated by regression techniques. S1te index curves for longleaf pine were developed...SOIL-SITE RELATIONSHIPS FOR NATURAL STANDS OF LONGLEAF PINE (PINUS PALUSTRIS MILL. ) IN EAST TEXAS A Thesis by ERIC HAYS LARSON Submitted to the Graduate College of Texas A8M University in partial fulfillment of the requirement...

Larson, Eric Hays

1971-01-01T23:59:59.000Z

478

Environmental factors affecting long-term stabilization of radon suppression covers for uranium mill tailings  

SciTech Connect (OSTI)

Pacific Northwest Laboratory is investigating the use of a rock armoring blanket (riprap) to mitigate wind and water erosion of an earthen radon suppression cover applied to uranium mill tailings. To help determine design stresses for the tailings piles, environmental parameters are characterized for the five active uranium-producing regions on a site-specific basis. Only conventional uranium mills that are currently operating or that are scheduled to open in the mid 1980s are considered. Available data indicate that flooding has the most potential for disrupting a tailings pile. The arid regions of the Wyoming Basins and the Colorado Plateau are subject to brief storms of high intensity. The Texas Gulf Coast has the highest potential for extreme precipitation from hurricane-related storms. Wind data indicate average wind speeds from 3 to 6 m/sec for the sites, but extremes of 40 m/sec can be expected. Tornado risks range from low to moderate. The Colorado Plateau has the highest seismic potential, with maximum acceleration caused by earthquakes ranging from 0.2 to 0.4 g. Any direct effect from volcanic eruption is negligible, as all mills are located 90 km or more from an igneous or hydrothermal system.

Young, J.K.; Long, L.W.; Reis, J.W.

1982-04-01T23:59:59.000Z

479

[Uranium Mill Tailings Remedial Action Project Office Quality Assurance Program Plan]. Revision 4  

SciTech Connect (OSTI)

The Uranium Mill Tailings Remedial Action (UMTRA) Project was established to accomplish remedial actions at inactive uranium mill tailings sites in accordance with Public Law 95-604, the Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA). The UMTRA Project`s mission is to stabilize and control the residual radioactive materials at designated sites in a safe and environmentally sound manner so as to minimize or eliminate radiation health hazards to the public. The US Department of Energy (DOE) UMTRA Project Office (UMTRA PO) directs the overall project. Since these efforts may involve possible risks to public health and safety, a quality assurance (QA) program that conforms to the applicable criteria (set forth in the reference documents) has been established to control the quality of the work. This document, the Quality Assurance Program Plan (QAPP), brings into one document the essential criteria to be applied on a selective basis, depending upon the nature of the activity being conducted, and describes how those criteria shall be applied to the UMTRA Project. The UMTRA PO shall require each Project contractor to prepare and submit for approval a more detailed QAPP that is based on the applicable criteria of this QAPP and the referenced documents. All QAPPs on the UMTRA Project shall fit within the framework of this plan.

Not Available

1992-06-01T23:59:59.000Z

480

[Uranium Mill Tailings Remedial Action Project Office Quality Assurance Program Plan  

SciTech Connect (OSTI)

The Uranium Mill Tailings Remedial Action (UMTRA) Project was established to accomplish remedial actions at inactive uranium mill tailings sites in accordance with Public Law 95-604, the Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA). The UMTRA Project's mission is to stabilize and control the residual radioactive materials at designated sites in a safe and environmentally sound manner so as to minimize or eliminate radiation health hazards to the public. The US Department of Energy (DOE) UMTRA Project Office (UMTRA PO) directs the overall project. Since these efforts may involve possible risks to public health and safety, a quality assurance (QA) program that conforms to the applicable criteria (set forth in the reference documents) has been established to control the quality of the work. This document, the Quality Assurance Program Plan (QAPP), brings into one document the essential criteria to be applied on a selective basis, depending upon the nature of the activity being conducted, and describes how those criteria shall be applied to the UMTRA Project. The UMTRA PO shall require each Project contractor to prepare and submit for approval a more detailed QAPP that is based on the applicable criteria of this QAPP and the referenced documents. All QAPPs on the UMTRA Project shall fit within the framework of this plan.

Not Available

1992-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "milling capacity short" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Paleoclimatic data applications: Long-term performance of uranium mill tailings repositories  

SciTech Connect (OSTI)

Abandoned uranium mill tailings sites in the Four Corners region are a lasting legacy of the Cold War. The U.S. Department of Energy (DOE) is designing landfill repositories that will isolate hazardous constituents of tailings from biological intrusion, erosion, and the underlying aquifer for up to 1,000 years. With evidence of relatively rapid past climate change, and model predictions of global climatic variation exceeding the historical record, DOE recognizes a need to incorporate possible ranges of future climatic and ecological change in the repository design process. In the Four Corners region, the center of uranium mining and milling activities in the United States, proxy paleoclimatic records may be useful not only as a window on the past, but also as analogs of possible local responses to future global change. We reconstructed past climate change using available proxy data from tree rings, packrat middens, lake sediment pollen, and archaeological records. Interpretation of proxy paleoclimatic records was based on present-day relationships between plant distribution, precipitation, and temperature along a generalized elevational gradient for the region. For the Monticello, Utah, uranium mill tailings site, this first approximation yielded mean annual temperature and precipitation ranges of 2 to 10{degrees} C, and 38 to 80 cm, respectively, corresponding to late glacial and Altithermal periods. These data are considered to be reasonable ranges of future climatic conditions that can be input to evaluations of groundwater recharge, radon-gas escape, erosion, frost penetration, and biointrusion in engineered earthen barriers designed to isolate tailings.

Waugh, W.J. [Environmental Sciences Lab., Grand Junction, CO (United States); Petersen, K.L. [Washington State Univ., Richland, WA (United States)

1995-09-01T23:59:59.000Z

482

The U.S. regulatory framework for long-term management of uranium mill tailings  

SciTech Connect (OSTI)

The US established the regulatory structure for the management, disposal, and long-term care of uranium mill tailings in 1978 with the passage of the Uranium Mill Tailings Radiation Control Act (UMTRCA) (Pub. L. 95-604). This legislation has governed the cleanup and disposal of uranium tailings at both inactive and active sites. The passage of the UMTRCA established a federal regulatory program for the cleanup and disposal of uranium mill tailings in the US. This program involves the DOE, the NRC, the EPA, various states and tribal governments, private licensees, and the general public. The DOE has completed surface remediation at 14 sites, with the remaining sites either under construction or in planning. The DOE`s UMTRA Project has been very successful in dealing with public and agency demands, particularly regarding disposal site selection and transportation issues. The active sites are also being cleaned up, but at a slower pace than the inactive sites, with the first site tentatively scheduled for completion in 1996.

Smythe, C. [Dept. of Energy, Albuquerque, NM (United States); Bierley, D.; Bradshaw, M. [Roy F. Weston, Inc., Albuquerque, NM (United States)

1995-03-01T23:59:59.000Z

483

Annual status report on the Uranium Mill Tailings Remedial Action Program  

SciTech Connect (OSTI)

This eleventh annual status report summarizes activities of the Uranium Mill Tailings Remedial Action (UMTRA) Project undertaken during Fiscal Year (FY) 1989 by the US Department of Energy (DOE) and other agencies. Project goals for FY 1990 are also presented. An annual report of this type was a statutory requirement through January 1, 1986, pursuant to the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law (PL) 95--604. The DOE will continue to submit an annual report through project completion in order to inform the public of yearly project status. Title I of the UMTRCA authorizes the DOE, in cooperation with affected states and Indian tribes within whose boundaries designated uranium processing sites are located, to provide a program of assessment and remedial action at such sites. The purpose of the remedial action is to stabilize and control the tailings and other residual radioactive materials located on the inactive uranium processing sites in a safe and environmentally sound manner and to minimize or eliminate potential radiation health hazards. Commercial and residential properties in the vicinity of designated processing sites that are contaminated with material from the sites, herein referred to as vicinity properties,'' are also eligible for remedial action. Included in the UMTRA Project are 24 inactive uranium processing sites and associated vicinity properties located in 10 states, and the vicinity properties associated with Edgemont, South Dakota, an inactive uranium mill currently owned by the Tennessee Valley Authority (TVA).

Not Available

1989-12-01T23:59:59.000Z

484

Combined biomass and black liquor gasifier/gas turbine cogeneration at pulp and paper mills  

SciTech Connect (OSTI)

Kraft pulp and paper mills generate large quantities of black liquor and byproduct biomass suitable for gasification. These fuels are used today for onsite cogeneration of heat and power in boiler/steam turbine systems. Gasification technologies under development would enable these fuels to be used in gas turbines. This paper reports results of detailed full-load performance modeling of pulp-mill cogeneration systems based on gasifier/gas turbine technologies. Pressurized, oxygen-blown black liquor gasification, the most advanced of proposed commercial black liquor gasifier designs, is considered, together with three alternative biomass gasifier designs under commercial development (high-pressure air-blown, low-pressure air-blown, and low-pressure indirectly-heated). Heavy-duty industrial gas turbines of the 70-MW{sub e} and 25-MW {sub e} class are included in the analysis. Results indicate that gasification-based cogeneration with biomass-derived fuels would transform a typical pulp mill into significant power exporter and would also offer possibilities for net reductions in emissions of carbon dioxide relative to present practice.

Larson, E.D.; Kreutz, T.G. [Princeton Univ., NJ (United States). Center for Energy and Environmental Studies; Consonni, S. [Politecnico di Milano, Milan (Italy). Dipt. di Energetica

1999-07-01T23:59:59.000Z

485

Baseline risk assessment of groundwater contamination at the Uranium Mill Tailings Site near Gunnison, Colorado  

SciTech Connect (OSTI)

This Baseline Risk Assessment of Groundwater Contamination at the Uranium Mill Tailings Site Near Gunnison, Colorado evaluates potential impacts to public health or the environment resulting from groundwater contamination at the former uranium mill processing site. The tailings and other contaminated material at this site are being placed in an off-site disposal cell by the US Department of Energy`s (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. Currently, the UMTRA Project is evaluating groundwater contamination. This is the second risk assessment of groundwater contamination at this site. The first risk assessment was performed primarily to evaluate existing domestic wells. This risk assessment evaluates the most contaminated monitor wells at the processing site. It will be used to assist in determining what remedial action is needed for contaminated groundwater at the site after the tailings are relocated. This risk assessment follows an approach outlined by the US Environmental Protection Agency (EPA). The first step is to evaluate groundwater data collected from monitor wells at the site. Evaluation of these data showed that the main contaminants in the groundwater are cadmium, cobalt, iron, manganese, sulfate, uranium, and some of the products of radioactive decay of uranium.

Not Available

1993-12-01T23:59:59.000Z

486

Short communication Dynamics of microbubble oscillators with delay coupling  

E-Print Network [OSTI]

of systems of coupled microbubbles in- volves taking into account the speed of sound in the liquid, which to travel from one bubble to another through the liquid medium that surrounds them. Using techniques from; coupled laser systems, high-speed milling, popu- lation dynamics and gene expression are some examples

Rand, Richard H.

487

Short-Range Nucleon-Nucleon Correlations  

SciTech Connect (OSTI)

Valence-shell nucleon knock-out experiments, such as 12C(e,e'p)11B, measure less strength then is predicted by independent particle shell model calculations. The theoretical solution to this problem is to include the correlations between the nucleons in the nucleus in the calculations. Motivated by these results, many electron scattering experiments have tried to directly observe these correlations in order to gain new insight into the short-range part of the nucleon-nucleon potential. Unfortunately, many competing mechanisms can cause the same observable final-state as an initial-state correlation, making truly isolating the signal extremely challenging. This paper reviews the recent experimental evidence for short-range correlations, as well as explores the possibility that such correlations are responsible for the EMC effect in the 0.3 < xB < 0.7 deep inelastic scattering ratios.

Douglas Higinbotham

2011-10-01T23:59:59.000Z

488

Short-Range Nucleon-Nucleon Correlations  

SciTech Connect (OSTI)

Valence-shell nucleon knock-out experiments, such as {sup 12}C(e,e'p){sup 11}B, measure less strength then is predicted by independent particle shell model calculations. The theoretical solution to this problem is to include the correlations between the nucleons in the nucleus in the calculations. Motivated by these results, many electron scattering experiments have tried to isolate the signal from these correlations in order to gain new insight into the short-range part of the nucleon-nucleon potential. Unfortunately, many competing mechanisms can cause the same observable final-state as an initial-state correlation, making truly isolating the signal extremely challenging. This paper reviews the recent experimental evidence for short-range correlations, as well as explores the possibility that such correlations are responsible for the EMC effect in the 0.3

Higinbotham, Douglas W. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23601 (United States)

2011-10-24T23:59:59.000Z

489

Predicting Operator Capacity for Supervisory Control of Multiple UAVs  

E-Print Network [OSTI]

Predicting Operator Capacity for Supervisory Control of Multiple UAVs M.L. Cummings, C. E. Nehme, J, uninhabited (also known as unmanned) ae- rial vehicles (UAVs) have become indispensable assets to militarized forces. UAVs require human guidance to varying degrees and often through several operators. However

Cummings, Mary "Missy"

490

Solar Photovoltaic Capacity F t P f d P li  

E-Print Network [OSTI]

6/19/2013 1 Solar Photovoltaic ­ Capacity F t P f d P li Generating Resources Advisory Committee Advisor Model (SAM), version 2013.1.15 Technology: Solar PV (PVWatts system model)Technology: Solar PV (MWh) (First year output, each year thereafter degrades 0.5%) 6 #12;6/19/2013 4 Shape of PNW Solar PV

491

CAPACITY DECISIONS WITH DEMAND FLUCTUATIONS AND CARBON LEAKAGE  

E-Print Network [OSTI]

Palaiseau, France April 2013 Abstract For carbon-intensive, internationally-traded industrial goods, a uni be partly oset by the increase of emissions in the rest of the world. The literature on carbon leakage hasCAPACITY DECISIONS WITH DEMAND FLUCTUATIONS AND CARBON LEAKAGE Guy MEUNIER Jean-Pierre PONSSARD

Paris-Sud XI, Université de

492

CAPACITY DECISIONS WITH DEMAND FLUCTUATIONS AND CARBON LEAKAGE  

E-Print Network [OSTI]

For carbon-intensive, internationally-traded industrial goods, a unilat- eral increase in the domestic CO2 be partly oset by the increase of emissions in the rest of the world. The literature on carbon leakage hasCAPACITY DECISIONS WITH DEMAND FLUCTUATIONS AND CARBON LEAKAGE Guy MEUNIER Jean-Pierre PONSSARD

Paris-Sud XI, Université de

493

Wind Farm Portfolio Optimization under Network Capacity Constraints  

E-Print Network [OSTI]

1 Wind Farm Portfolio Optimization under Network Capacity Constraints H´el`ene Le Cadre, Anthony of wind farms in a Market Coupling organization, for two Market Designs (exogenous prices and endogenous of efficient wind farm portfolios, is derived theoretically as a function of the number of wind farms

Paris-Sud XI, Université de

494

Linear Codes, Target Function Classes, and Network Computing Capacity  

E-Print Network [OSTI]

Linear Codes, Target Function Classes, and Network Computing Capacity Rathinakumar Appuswamy Submitted: May 6, 2011 Abstract We study the use of linear codes for network computing in single in network coding are applicable to network computing as well. Network computing problems arise in various

Franceschetti, Massimo

495

POSITIVITY CASES, ESTIMATES AND ASYMPTOTIC EXPANSIONS FOR CONDENSER CAPACITIES.  

E-Print Network [OSTI]

POSITIVITY CASES, ESTIMATES AND ASYMPTOTIC EXPANSIONS FOR CONDENSER CAPACITIES. ALAIN BONNAF´E Abstract. We study positivity cases, estimates and asymptotic expansions of condenser p the internal part of the condenser has a non-empty interior. The study of the point and its approximation

Boyer, Edmond

496

The Capacity Loss of Dense Constellations Tobias Koch  

E-Print Network [OSTI]

high SNR, our results recover the power loss of 1.53dB for square signal constellations without-noise channels for suitably high signal- to-noise ratio. Our expression for the capacity loss recovers the power loss of 1.53dB for square signal constellations. I. INTRODUCTION As it is well known, the channel

497

TRENDS IN ELECTRICITY CONSUMPTION, PEAK DEMAND, AND GENERATING CAPACITY IN  

E-Print Network [OSTI]

PWP-085 TRENDS IN ELECTRICITY CONSUMPTION, PEAK DEMAND, AND GENERATING CAPACITY IN CALIFORNIA, California 94720-5180 www.ucei.org #12;TRENDS IN ELECTRICITY CONSUMPTION, PEAK DEMAND, AND GENERATING** Abstract This study analyzes state and regional electricity supply and demand trends for the eleven states

California at Berkeley. University of

498

Dynamic Energy-Aware Capacity Provisioning for Cloud Computing Environments  

E-Print Network [OSTI]

reduction in energy cost, while maintaining an acceptable average scheduling delay for individual tasksDynamic Energy-Aware Capacity Provisioning for Cloud Computing Environments Qi Zhang University by amortizing initial capital investment over large number of machines, they also incur tremendous energy cost

Boutaba, Raouf

499

A CAUTIONARY NOTE REGARDING THE DATA INTEGRITY CAPACITY  

E-Print Network [OSTI]

assurance components, as well as the integrity of data read from high assurance repositories and displayedA CAUTIONARY NOTE REGARDING THE DATA INTEGRITY CAPACITY OF CERTAIN SECURE SYSTEMS Cynthia E. Irvine of architecture. We discuss the general integrity property that systems can only be trusted to manage modi able

Irvine, Cynthia E.

500

Sizing Storage and Wind Generation Capacities in Remote Power Systems  

E-Print Network [OSTI]

Sizing Storage and Wind Generation Capacities in Remote Power Systems by Andy Gassner B capital investment costs of renewable energy technologies. Specifically, wind power represents the most and small power systems. However, the variability due to the stochastic nature of the wind resource

Victoria, University of