National Library of Energy BETA

Sample records for metric ton inclusive

  1. Energy Department Sponsored Project Captures One Millionth Metric Ton of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CO2 | Department of Energy Sponsored Project Captures One Millionth Metric Ton of CO2 Energy Department Sponsored Project Captures One Millionth Metric Ton of CO2 June 27, 2014 - 11:09am Addthis An aerial view of Air Products’ steam methane reforming facility at Port Arthur, Texas. | Photo courtesy of Air Products and Chemicals Inc. An aerial view of Air Products' steam methane reforming facility at Port Arthur, Texas. | Photo courtesy of Air Products and Chemicals Inc. Allison Lantero

  2. "(Million Metric Tons Carbon Dioxide)"

    U.S. Energy Information Administration (EIA) Indexed Site

    Source: International Energy Outlook 2010" "Report #: DOE/EIA-0484(2010)" "application/vnd.ms-excel" "U.S. history values from this report" "U.S. projections from AEO2011, early release" "Table 4. World energy-related carbon dioxide emissions and shares by region, 1990-2035",,,,,,,,,,,,,,"Additional data for analysis" "(Million Metric Tons Carbon Dioxide)"

  3. U.S. Removes Nine Metric Tons of Plutonium From Nuclear Weapons Stockpile |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Removes Nine Metric Tons of Plutonium From Nuclear Weapons Stockpile U.S. Removes Nine Metric Tons of Plutonium From Nuclear Weapons Stockpile September 17, 2007 - 2:41pm Addthis Declaration Reinforces U.S. Commitment to Nonproliferation VIENNA, AUSTRIA - Secretary of Energy Samuel W. Bodman today announced that the Department of Energy's National Nuclear Security Administration (NNSA) will remove nine metric tons of plutonium from further use as fissile material in U.S.

  4. DOE Will Dispose of 34 Metric Tons of Plutonium by Turning it into Fuel for

    National Nuclear Security Administration (NNSA)

    Civilian Reactors | National Nuclear Security Administration Will Dispose of 34 Metric Tons of Plutonium by Turning it into Fuel for Civilian Reactors DOE Will Dispose of 34 Metric Tons of Plutonium by Turning it into Fuel for Civi Washington, DC Secretary Abraham announced that DOE will dispose of 34 metric tons of surplus weapons grade plutonium by turning the material into mixed oxide fuel (MOX) for use in nuclear reactors. The decision follows an exhaustive Administration review of

  5. Energy Department Project Captures and Stores One Million Metric Tons of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Carbon | Department of Energy One Million Metric Tons of Carbon Energy Department Project Captures and Stores One Million Metric Tons of Carbon January 8, 2015 - 11:18am Addthis News Media Contact 202-586-4940 Energy Department Project Captures and Stores One Million Metric Tons of Carbon Project Achieves Major Milestone by Successfully Injecting Carbon into Saline Formation WASHINGTON - As part of President Obama's all-of-the-above energy strategy, the Department of Energy announced today

  6. Taking the One-Metric-Ton Challenge | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Taking the One-Metric-Ton ... Taking the One-Metric-Ton Challenge Posted: January 13, 2016 - 4:46pm NNSA Uranium Program Manager Tim Driscoll speaks with the One-Metric-Ton Challenge team in Building 9212. The team has undertaken an extensive dedicated maintenance effort to improve metal production equipment reliability and reduce unexpected down time, with an end goal of significantly increasing purified metal production by fiscal year 2017. Last year, NNSA Uranium Program Manager Tim Driscoll

  7. 11,202,720 Metric Tons of CO2 Injected as of October 14, 2015

    Office of Energy Efficiency and Renewable Energy (EERE)

    This carbon dioxide (CO2) has been injected in the United States as part of DOEs Clean Coal Research, Development, and Demonstration Programs. One million metric tons of CO2 is equivalent to the...

  8. 11,202,720 Metric Tons of CO2 Injected as of October 14, 2015...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    This carbon dioxide (CO2) has been injected in the United States as part of DOE's Clean Coal Research, Development, and Demonstration Programs. One million metric tons of CO2 is ...

  9. DOE to Remove 200 Metric Tons of Highly Enriched Uranium from U.S. Nuclear

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Weapons Stockpile | Department of Energy to Remove 200 Metric Tons of Highly Enriched Uranium from U.S. Nuclear Weapons Stockpile DOE to Remove 200 Metric Tons of Highly Enriched Uranium from U.S. Nuclear Weapons Stockpile November 7, 2005 - 12:38pm Addthis Will Be Redirected to Naval Reactors, Down-blended or Used for Space Programs WASHINGTON, DC - Secretary of Energy Samuel W. Bodman today announced that the Department of Energy's (DOE) National Nuclear Security Administration (NNSA) will

  10. Table 11.4 Nitrous Oxide Emissions, 1980-2009 (Thousand Metric Tons of Nitrous Oxide)

    U.S. Energy Information Administration (EIA) Indexed Site

    Nitrous Oxide Emissions, 1980-2009 (Thousand Metric Tons of Nitrous Oxide) Year Energy Sources Waste Management Agricultural Sources Industrial Processes 3 Total Mobile Combustion 1 Stationary Combustion 2 Total Waste Combustion Human Sewage in Wastewater Total Nitrogen Fertilization of Soils Crop Residue Burning Solid Waste of Domesticated Animals Total 1980 60 44 104 1 10 11 364 1 75 440 88 642 1981 63 44 106 1 10 11 364 2 74 440 84 641 1982 67 42 108 1 10 11 339 2 74 414 80 614 1983 71 43 114

  11. Table 11.3 Methane Emissions, 1980-2009 (Million Metric Tons of Methane)

    U.S. Energy Information Administration (EIA) Indexed Site

    Methane Emissions, 1980-2009 (Million Metric Tons of Methane) Year Energy Sources Waste Management Agricultural Sources Industrial Processes 9 Total 5 Coal Mining Natural Gas Systems 1 Petroleum Systems 2 Mobile Com- bustion 3 Stationary Com- bustion 4 Total 5 Landfills Waste- water Treatment 6 Total 5 Enteric Fermen- tation 7 Animal Waste 8 Rice Cultivation Crop Residue Burning Total 5 1980 3.06 4.42 NA 0.28 0.45 8.20 10.52 0.52 11.04 5.47 2.87 0.48 0.04 8.86 0.17 28.27 1981 2.81 5.02 NA .27

  12. In Milestone, Energy Department Projects Safely and Permanently Store 10 Million Metric Tons of Carbon Dioxide

    Broader source: Energy.gov [DOE]

    Carbon Capture and Storage projects supported by the Department reached a milestone of 10 million tons of carbon dioxide.

  13. Table 11.1 Carbon Dioxide Emissions From Energy Consumption by Source, 1949-2011 (Million Metric Tons of Carbon Dioxide )

    U.S. Energy Information Administration (EIA) Indexed Site

    Carbon Dioxide Emissions From Energy Consumption by Source, 1949-2011 (Million Metric Tons of Carbon Dioxide 1) Year Coal 3 Natural Gas 4 Petroleum Total 2,9 Biomass 2 Aviation Gasoline Distillate Fuel Oil 5 Jet Fuel Kero- sene LPG 6 Lubri- cants Motor Gasoline 7 Petroleum Coke Residual Fuel Oil Other 8 Total Wood 10 Waste 11 Fuel Ethanol 12 Bio- diesel Total 1949 1,118 270 12 140 NA 42 13 7 329 8 244 25 820 2,207 145 NA NA NA 145 1950 1,152 313 14 168 NA 48 16 9 357 8 273 26 918 2,382 147 NA NA

  14. Table 11.2a Carbon Dioxide Emissions From Energy Consumption: Residential Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide )

    U.S. Energy Information Administration (EIA) Indexed Site

    a Carbon Dioxide Emissions From Energy Consumption: Residential Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide 1) Year Coal Natural Gas 3 Petroleum Retail Electricity 5 Total 2 Biomass 2 Distillate Fuel Oil 4 Kerosene Liquefied Petroleum Gases Total Wood 6 Total 6 1949 121 55 51 21 7 80 66 321 99 99 1950 120 66 61 25 9 95 69 350 94 94 1951 111 81 68 27 10 105 78 374 90 90 1952 103 89 70 27 10 108 85 385 84 84 1953 92 93 71 26 11 108 94 387 78 78 1954 82 104 79 27 12 118 99 404 75 75

  15. Table 11.2c Carbon Dioxide Emissions From Energy Consumption: Industrial Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide )

    U.S. Energy Information Administration (EIA) Indexed Site

    c Carbon Dioxide Emissions From Energy Consumption: Industrial Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide 1) Year Coal Coal Coke Net Imports Natural Gas 3 Petroleum Retail Elec- tricity 8 Total 2 Biomass 2 Distillate Fuel Oil 4 Kero- sene LPG 5 Lubri- cants Motor Gasoline 6 Petroleum Coke Residual Fuel Oil Other 7 Total Wood 9 Waste 10 Fuel Ethanol 11 Total 1949 500 -1 166 41 18 3 3 16 8 95 25 209 120 995 44 NA NA 44 1950 531 (s) 184 51 20 4 3 18 8 110 26 239 140 1,095 50 NA NA 50

  16. Table 11.2d Carbon Dioxide Emissions From Energy Consumption: Transportation Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide )

    U.S. Energy Information Administration (EIA) Indexed Site

    d Carbon Dioxide Emissions From Energy Consumption: Transportation Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide 1) Year Coal Natural Gas 3 Petroleum Retail Elec- tricity 7 Total 2 Biomass 2 Aviation Gasoline Distillate Fuel Oil 4 Jet Fuel LPG 5 Lubricants Motor Gasoline 6 Residual Fuel Oil Total Fuel Ethanol 8 Biodiesel Total 1949 161 NA 12 30 NA (s) 4 306 91 443 6 611 NA NA NA 1950 146 7 14 35 NA (s) 5 332 95 481 6 640 NA NA NA 1951 129 11 18 42 NA (s) 6 360 102 529 7 675 NA NA NA

  17. Table 11.2b Carbon Dioxide Emissions From Energy Consumption: Commercial Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide )

    U.S. Energy Information Administration (EIA) Indexed Site

    b Carbon Dioxide Emissions From Energy Consumption: Commercial Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide 1) Year Coal Natural Gas 3 Petroleum Retail Electricity 7 Total 2 Biomass 2 Distillate Fuel Oil 4 Kerosene LPG 5 Motor Gasoline 6 Petroleum Coke Residual Fuel Oil Total Wood 8 Waste 9 Fuel Ethanol 10 Total 1949 148 19 16 3 2 7 NA 28 55 58 280 2 NA NA 2 1950 147 21 19 3 2 7 NA 33 66 63 297 2 NA NA 2 1951 125 25 21 4 3 8 NA 34 70 69 289 2 NA NA 2 1952 112 28 22 4 3 8 NA 35 71 73

  18. Table 11.2e Carbon Dioxide Emissions From Energy Consumption: Electric Power Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide )

    U.S. Energy Information Administration (EIA) Indexed Site

    e Carbon Dioxide Emissions From Energy Consumption: Electric Power Sector, 1949-2011 (Million Metric Tons of Carbon Dioxide 1) Year Coal Natural Gas 3 Petroleum Geo- thermal Non- Biomass Waste 5 Total 2 Biomass 2 Distillate Fuel Oil 4 Petroleum Coke Residual Fuel Oil Total Wood 6 Waste 7 Total 1949 187 30 2 NA 30 33 NA NA 250 1 NA 1 1950 206 35 2 NA 35 37 NA NA 278 1 NA 1 1951 235 42 2 NA 29 31 NA NA 308 1 NA 1 1952 240 50 2 NA 31 33 NA NA 323 1 NA 1 1953 260 57 3 NA 38 40 NA NA 358 (s) NA (s)

  19. Metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Metrics Metrics Los Alamos expands its innovation network by engaging in sponsored research and licensing across technical disciplines. These agreements are the basis of a working relationship with industry and other research institutions and highlight the diversity of our collaborations. Los Alamos has a remarkable 70-year legacy of creating entirely new technologies that have revolutionized the country's understanding of science and engineering. Collaborations Data from Fiscal Year 2014. FY14

  20. Table 11.5a Emissions From Energy Consumption for Electricity Generation and Useful Thermal Output: Total (All Sectors), 1989-2010 (Sum of Tables 11.5b and 11.5c; Metric Tons of Gas)

    U.S. Energy Information Administration (EIA) Indexed Site

    a Emissions From Energy Consumption for Electricity Generation and Useful Thermal Output: Total (All Sectors), 1989-2010 (Sum of Tables 11.5b and 11.5c; Metric Tons of Gas) Year Carbon Dioxide 1 Sulfur Dioxide Nitrogen Oxides Coal 2 Natural Gas 3 Petroleum 4 Geo- thermal 5 Non- Biomass Waste 6 Total Coal 2 Natural Gas 3 Petroleum 4 Other 7 Total Coal 2 Natural Gas 3 Petroleum 4 Other 7 Total 1989 1,573,566,415 218,383,703 145,398,976 363,247 5,590,014 1,943,302,355 14,468,564 1,059 984,406

  1. Table 11.5b Emissions From Energy Consumption for Electricity Generation and Useful Thermal Output: Electric Power Sector, 1989-2010 (Subset of Table 11.5a; Metric Tons of Gas)

    U.S. Energy Information Administration (EIA) Indexed Site

    b Emissions From Energy Consumption for Electricity Generation and Useful Thermal Output: Electric Power Sector, 1989-2010 (Subset of Table 11.5a; Metric Tons of Gas) Year Carbon Dioxide 1 Sulfur Dioxide Nitrogen Oxides Coal 2 Natural Gas 3 Petroleum 4 Geo- thermal 5 Non- Biomass Waste 6 Total Coal 2 Natural Gas 3 Petroleum 4 Other 7 Total Coal 2 Natural Gas 3 Petroleum 4 Other 7 Total 1989 1,520,229,870 169,653,294 133,545,718 363,247 4,365,768 1,828,157,897 13,815,263 832 809,873 6,874

  2. Table 11.5c Emissions From Energy Consumption for Electricity Generation and Useful Thermal Output: Commercial and Industrial Sectors, 1989-2010 (Subset of Table 11.5a; Metric Tons of Gas)

    U.S. Energy Information Administration (EIA) Indexed Site

    c Emissions From Energy Consumption for Electricity Generation and Useful Thermal Output: Commercial and Industrial Sectors, 1989-2010 (Subset of Table 11.5a; Metric Tons of Gas) Year Carbon Dioxide 1 Sulfur Dioxide Nitrogen Oxides Coal 2 Natural Gas 3 Petroleum 4 Geo- thermal 5 Non- Biomass Waste 6 Total Coal 2 Natural Gas 3 Petroleum 4 Other 7 Total Coal 2 Natural Gas 3 Petroleum 4 Other 7 Total Commercial Sector 8<//td> 1989 2,319,630 1,542,083 637,423 [ –] 803,754 5,302,890 37,398 4

  3. DOE Partner Begins Injecting 50,000 Tons of CO2 in Michigan Basin

    Broader source: Energy.gov [DOE]

    Building on an initial injection project of 10,000 metric tons of carbon dioxide into a Michigan geologic formation, a U.S. Department of Energy team of regional partners has begun injecting 50,000 additional tons into the formation, which is believed capable of storing hundreds of years worth of CO2, a greenhouse gas that contributes to climate change.

  4. Transportation system benefits of early deployment of a 75-ton multipurpose canister system

    SciTech Connect (OSTI)

    Wankerl, M.W.; Schmid, S.P.

    1995-12-31

    In 1993 the US Civilian Radioactive Waste Management System (CRWMS) began developing two multipurpose canister (MPC) systems to provide a standardized method for interim storage and transportation of spent nuclear fuel (SNF) at commercial nuclear power plants. One is a 75-ton concept with an estimated payload of about 6 metric tons (t) of SNF, and the other is a 125-ton concept with an estimated payload of nearly 11 t of SNF. These payloads are two to three times the payloads of the largest currently certified US rail transport casks, the IF-300. Although is it recognized that a fully developed 125-ton MPC system is likely to provide a greater cost benefit, and radiation exposure benefit than the lower-capacity 75-ton MPC, the authors of this paper suggest that development and deployment of the 75-ton MPC prior to developing and deploying a 125-ton MPC is a desirable strategy. Reasons that support this are discussed in this paper.

  5. STAR METRICS

    Broader source: Energy.gov [DOE]

    Energy continues to define Phase II of the STAR METRICS program, a collaborative initiative to track Research and Development expenditures and their outcomes. Visit the STAR METRICS website for...

  6. E TON Solar Tech | Open Energy Information

    Open Energy Info (EERE)

    Solar Tech Jump to: navigation, search Name: E-TON Solar Tech Place: Tainan, Taiwan Zip: 709 Product: Taiwan-based manufacturer of PV cells. Coordinates: 22.99721, 120.180862...

  7. Bioenergy Impacts … Billion Dry Tons

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    by 2030 at least one billion dry tons of non-food biomass resources, yielding up to 60 billion gallons of biofuels, as well as bio- based chemicals, products, and electricity. ...

  8. Diversity, Inclusion

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Workplace Diversity, Inclusion Diversity, Inclusion Explore the multiple dimensions of a career at Los Alamos Lab: work with the best minds on the planet in an inclusive...

  9. Metric Presentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MODERN GRID S T R A T E G Y Smart Grid Metrics Monitoring our Progress Smart Grid Implementation Workshop Joe Miller - Modern Grid Team June 19, 2008 1 Conducted by the National Energy Technology Laboratory Funded by the U.S. Department of Energy, Office of Electricity Delivery and Energy Reliability 2 Office of Electricity Delivery and Energy Reliability MODERN GRID S T R A T E G Y Many are working on the Smart Grid FERC DOE-OE Grid 2030 GridWise Alliance EEI NERC (FM) DOE/NETL Modern Grid

  10. Billion Ton Study-A Historical Perspective | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Billion Ton Study-A Historical Perspective Billion Ton Study-A Historical Perspective Breakout Session 1A: Biomass Feedstocks for the Bioeconomy Billion Ton Study-A Historical Perspective Bryce Stokes, Senior Advisor, CNJV PDF icon stokes_bioenergy_2015.pdf More Documents & Publications Biomass Econ 101: Measuring the Technological Improvements on Feedstocks Costs WEBINAR: A CHANGING MARKET FOR BIOFUELS AND BIOPRODUCTS U.S. Billion-Ton Update: Biomass Supply for a Bioenergy and Bioproducts

  11. 10,651,176 Metric Tons of CO2 Injected as of September 16, 2015...

    Broader source: Energy.gov (indexed) [DOE]

    Products has successfully retrofitted its two Port Arthur SMRs with a vacuum swing adsorption system to separate the CO2 from the process gas stream, followed by compression and...

  12. NNSA Eliminates 100 Metric Tons Of Weapons-Grade Nuclear Material...

    National Nuclear Security Administration (NNSA)

    secure and less expensive nuclear weapons complex. ... sale of LEU for safe use in power and research reactors around the world. ... NNSA maintains and enhances the safety, security, ...

  13. DOE to Remove 200 Metric Tons of Highly Enriched Uranium from...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Will Be Redirected to Naval Reactors, Down-blended or Used for Space Programs WASHINGTON, ... Approximately 20 MT will be reserved for space and research reactors that currently use ...

  14. DOE Will Dispose of 34 Metric Tons of Plutonium by Turning it...

    National Nuclear Security Administration (NNSA)

    Administration review of non-proliferation programs, including alternative technologies to dispose of surplus plutonium to meet the non-proliferation goals agreed to by the United ...

  15. 11,970,363 Metric Tons of CO2 Injected as of February 23, 2016...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Air Products has successfully retrofitted its two Port Arthur SMRs with a vacuum swing adsorption system to separate the CO2 from the process gas stream, followed by compression ...

  16. 10,422,136 Metric Tons of CO2 Injected as of August 21, 2015...

    Broader source: Energy.gov (indexed) [DOE]

    The projects currently injecting CO2 within DOE's Regional Carbon Sequestration Partnership Program and the Major Demonstration Program are detailed below. Regional Carbon...

  17. 11,970,363 Metric Tons of CO2 Injected as of February 23, 2016...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The network of seven RCSPs are currently conducting field tests which involve integrated system testing and validation of geologic storage, simulation and risk assessment, and ...

  18. Energy Department Project Captures and Stores more than One Million Metric

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tons of CO2 | Department of Energy more than One Million Metric Tons of CO2 Energy Department Project Captures and Stores more than One Million Metric Tons of CO2 June 26, 2014 - 11:30am Addthis Aerial view of Air Products’ existing steam methane reforming facility at Port Arthur, Texas, with new carbon-capture units and central co-gen and CO2 product compressor. | Photo courtesy of Air Products and Chemicals Inc. Aerial view of Air Products' existing steam methane reforming facility at

  19. ARM - 2008 Performance Metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 Performance Metrics Science Research Themes Research Highlights Journal Articles Collaborations Atmospheric System Research (ASR) Earth System Modeling Regional & Global Climate...

  20. ARM - 2006 Performance Metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 Performance Metrics Science Research Themes Research Highlights Journal Articles Collaborations Atmospheric System Research (ASR) Earth System Modeling Regional & Global Climate...

  1. ARM - 2009 Performance Metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9 Performance Metrics Science Research Themes Research Highlights Journal Articles Collaborations Atmospheric System Research (ASR) Earth System Modeling Regional & Global Climate...

  2. Webinar: Building the Billion Ton Bioeconomy | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Building the Billion Ton Bioeconomy Webinar: Building the Billion Ton Bioeconomy May 5, 2016 2:00PM to 4:00PM EDT Online Join the Biomass Research and Development (R&D) Board Operations Committee at a bioeconomy listening session on Thursday, May 5, 2 p.m.-4 p.m. Eastern Time. During the listening session, titled "Building a Billion Ton Bioeconomy in the United States," we encourage attendees to provide their thoughts and comments and to ask questions about the potential to grow

  3. Picture of the Week: The 100-Ton Test

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 The 100-Ton Test Before the historic Trinity test on July 16th, 1945, Los Alamos scientists conducted a host of other experiments designed to ensure that they would be ready to...

  4. Surveillance metrics sensitivity study.

    SciTech Connect (OSTI)

    Hamada, Michael S.; Bierbaum, Rene Lynn; Robertson, Alix A.

    2011-09-01

    In September of 2009, a Tri-Lab team was formed to develop a set of metrics relating to the NNSA nuclear weapon surveillance program. The purpose of the metrics was to develop a more quantitative and/or qualitative metric(s) describing the results of realized or non-realized surveillance activities on our confidence in reporting reliability and assessing the stockpile. As a part of this effort, a statistical sub-team investigated various techniques and developed a complementary set of statistical metrics that could serve as a foundation for characterizing aspects of meeting the surveillance program objectives. The metrics are a combination of tolerance limit calculations and power calculations, intending to answer level-of-confidence type questions with respect to the ability to detect certain undesirable behaviors (catastrophic defects, margin insufficiency defects, and deviations from a model). Note that the metrics are not intended to gauge product performance but instead the adequacy of surveillance. This report gives a short description of four metrics types that were explored and the results of a sensitivity study conducted to investigate their behavior for various inputs. The results of the sensitivity study can be used to set the risk parameters that specify the level of stockpile problem that the surveillance program should be addressing.

  5. Metric Construction | Open Energy Information

    Open Energy Info (EERE)

    Metric Construction Jump to: navigation, search Name: Metric Construction Place: Boston, MA Information About Partnership with NREL Partnership with NREL Yes Partnership Type Test...

  6. Cyber threat metrics.

    SciTech Connect (OSTI)

    Frye, Jason Neal; Veitch, Cynthia K.; Mateski, Mark Elliot; Michalski, John T.; Harris, James Mark; Trevino, Cassandra M.; Maruoka, Scott

    2012-03-01

    Threats are generally much easier to list than to describe, and much easier to describe than to measure. As a result, many organizations list threats. Fewer describe them in useful terms, and still fewer measure them in meaningful ways. This is particularly true in the dynamic and nebulous domain of cyber threats - a domain that tends to resist easy measurement and, in some cases, appears to defy any measurement. We believe the problem is tractable. In this report we describe threat metrics and models for characterizing threats consistently and unambiguously. The purpose of this report is to support the Operational Threat Assessment (OTA) phase of risk and vulnerability assessment. To this end, we focus on the task of characterizing cyber threats using consistent threat metrics and models. In particular, we address threat metrics and models for describing malicious cyber threats to US FCEB agencies and systems.

  7. Defining a Standard Metric for Electricity Savings

    SciTech Connect (OSTI)

    Brown, Marilyn; Akbari, Hashem; Blumstein, Carl; Koomey, Jonathan; Brown, Richard; Calwell, Chris; Carter, Sheryl; Cavanagh, Ralph; Chang, Audrey; Claridge, David; Craig, Paul; Diamond, Rick; Eto, Joseph H.; Fulkerson, William; Gadgil, Ashok; Geller, Howard; Goldemberg, Jose; Goldman, Chuck; Goldstein, David B.; Greenberg, Steve; Hafemeister, David; Harris, Jeff; Harvey, Hal; Heitz, Eric; Hirst, Eric; Hummel, Holmes; Kammen, Dan; Kelly, Henry; Laitner, Skip; Levine, Mark; Lovins, Amory; Masters, Gil; McMahon, James E.; Meier, Alan; Messenger, Michael; Millhone, John; Mills, Evan; Nadel, Steve; Nordman, Bruce; Price, Lynn; Romm, Joe; Ross, Marc; Rufo, Michael; Sathaye, Jayant; Schipper, Lee; Schneider, Stephen H; Sweeney, James L; Verdict, Malcolm; Vorsatz, Diana; Wang, Devra; Weinberg, Carl; Wilk, Richard; Wilson, John; Worrell, Ernst

    2009-03-01

    The growing investment by governments and electric utilities in energy efficiency programs highlights the need for simple tools to help assess and explain the size of the potential resource. One technique that is commonly used in this effort is to characterize electricity savings in terms of avoided power plants, because it is easier for people to visualize a power plant than it is to understand an abstraction such as billions of kilowatt-hours. Unfortunately, there is no standardization around the characteristics of such power plants. In this letter we define parameters for a standard avoided power plant that have physical meaning and intuitive plausibility, for use in back-of-the-envelope calculations. For the prototypical plant this article settles on a 500 MW existing coal plant operating at a 70percent capacity factor with 7percent T&D losses. Displacing such a plant for one year would save 3 billion kW h per year at the meter and reduce emissions by 3 million metric tons of CO2 per year. The proposed name for this metric is the Rosenfeld, in keeping with the tradition among scientists of naming units in honor of the person most responsible for the discovery and widespread adoption of the underlying scientific principle in question--Dr. Arthur H. Rosenfeld.

  8. THERMAL MODELING ANALYSIS OF SRS 70 TON CASK

    SciTech Connect (OSTI)

    Lee, S.; Jordan, J.; Hensel, S.

    2011-03-08

    The primary objective of this work was to perform the thermal calculations to evaluate the Material Test Reactor (MTR) fuel assembly temperatures inside the SRS 70-Ton Cask loaded with various bundle powers. MTR fuel consists of HFBR, MURR, MIT, and NIST. The MURR fuel was used to develop a bounding case since it is the fuel with the highest heat load. The results will be provided for technical input for the SRS 70 Ton Cask Onsite Safety Assessment. The calculation results show that for the SRS 70 ton dry cask with 2750 watts total heat source with a maximum bundle heat of 670 watts and 9 bundles of MURR bounding fuel, the highest fuel assembly temperatures are below about 263 C. Maximum top surface temperature of the plastic cover is about 112 C, much lower than its melting temperature 260 C. For 12 bundles of MURR bounding fuel with 2750 watts total heat and a maximum fuel bundle of 482 watts, the highest fuel assembly temperatures are bounded by the 9 bundle case. The component temperatures of the cask were calculated by a three-dimensional computational fluid dynamics approach. The modeling calculations were performed by considering daily-averaged solar heat flux.

  9. Metrics for Energy Resilience

    SciTech Connect (OSTI)

    Paul E. Roege; Zachary A. Collier; James Mancillas; John A. McDonagh; Igor Linkov

    2014-09-01

    Energy lies at the backbone of any advanced society and constitutes an essential prerequisite for economic growth, social order and national defense. However there is an Achilles heel to today?s energy and technology relationship; namely a precarious intimacy between energy and the fiscal, social, and technical systems it supports. Recently, widespread and persistent disruptions in energy systems have highlighted the extent of this dependence and the vulnerability of increasingly optimized systems to changing conditions. Resilience is an emerging concept that offers to reconcile considerations of performance under dynamic environments and across multiple time frames by supplementing traditionally static system performance measures to consider behaviors under changing conditions and complex interactions among physical, information and human domains. This paper identifies metrics useful to implement guidance for energy-related planning, design, investment, and operation. Recommendations are presented using a matrix format to provide a structured and comprehensive framework of metrics relevant to a system?s energy resilience. The study synthesizes previously proposed metrics and emergent resilience literature to provide a multi-dimensional model intended for use by leaders and practitioners as they transform our energy posture from one of stasis and reaction to one that is proactive and which fosters sustainable growth.

  10. Sheet1 Water Availability Metric (Acre-Feet/Yr) Water Cost Metric ($/Acre-Foot)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sheet1 Water Availability Metric (Acre-Feet/Yr) Water Cost Metric ($/Acre-Foot) Current Water Use (Acre-Feet/Yr) Projected Use in 2030 (Acre-Feet/Yr) HUC_8 STATE BASIN SUBBASIN UNAPPROPRIATED SURFACE WATER METRIC UNAPPROPRIATED GROUNDWATER METRIC APPROPRIATED WATER METRIC BRACKISH GROUNDWATER METRIC WASTEWATER METRIC UNAPPROPRIATED GROUNDWATER COST METRIC APPROPRIATED WATER COST METRIC BRACKISH GROUNDWATER COST METRIC WASTEWATER COST METRIC M&I_2012 AG_2012 ENVIRONMENT 2012 THERMOELECTIC

  11. Module 6 - Metrics, Performance Measurements and Forecasting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    6 - Metrics, Performance Measurements and Forecasting Module 6 - Metrics, Performance Measurements and Forecasting This module focuses on the metrics and performance measurement ...

  12. Ames Laboratory Metrics | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Metrics Document Number: NA Effective Date: 01/2016 File (public): PDF icon ameslab_metrics_01-14-16

  13. U.S. Manufacturers Save $1 Billion, 11 Million Tons of CO2 through...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    U.S. Manufacturers Save 1 Billion, 11 Million Tons of CO2 through Energy Efficiency Investments U.S. Manufacturers Save 1 Billion, 11 Million Tons of CO2 through Energy...

  14. Neutrino physics with multi-ton scale liquid xenon detectors

    SciTech Connect (OSTI)

    Baudis, L.; Ferella, A.; Kish, A.; Manalaysay, A.; Undagoitia, T. Marrodn; Schumann, M., E-mail: laura.baudis@physik.uzh.ch, E-mail: alfredo.ferella@lngs.infn.it, E-mail: alexkish@physik.uzh.ch, E-mail: aaronm@ucdavis.edu, E-mail: marrodan@mpi-hd.mpg.de, E-mail: marc.schumann@lhep.unibe.ch [Physik Institut, University of Zrich, Winterthurerstrasse 190, Zrich, CH-8057 (Switzerland)

    2014-01-01

    We study the sensitivity of large-scale xenon detectors to low-energy solar neutrinos, to coherent neutrino-nucleus scattering and to neutrinoless double beta decay. As a concrete example, we consider the xenon part of the proposed DARWIN (Dark Matter WIMP Search with Noble Liquids) experiment. We perform detailed Monte Carlo simulations of the expected backgrounds, considering realistic energy resolutions and thresholds in the detector. In a low-energy window of 230 keV, where the sensitivity to solar pp and {sup 7}Be-neutrinos is highest, an integrated pp-neutrino rate of 5900 events can be reached in a fiducial mass of 14 tons of natural xenon, after 5 years of data. The pp-neutrino flux could thus be measured with a statistical uncertainty around 1%, reaching the precision of solar model predictions. These low-energy solar neutrinos will be the limiting background to the dark matter search channel for WIMP-nucleon cross sections below ? 2 10{sup ?48} cm{sup 2} and WIMP masses around 50 GeV?c{sup ?2}, for an assumed 99.5% rejection of electronic recoils due to elastic neutrino-electron scatters. Nuclear recoils from coherent scattering of solar neutrinos will limit the sensitivity to WIMP masses below ? 6 GeV?c{sup ?2} to cross sections above ? 4 10{sup ?45}cm{sup 2}. DARWIN could reach a competitive half-life sensitivity of 5.6 10{sup 26} y to the neutrinoless double beta decay of {sup 136}Xe after 5 years of data, using 6 tons of natural xenon in the central detector region.

  15. Daylight metrics and energy savings

    SciTech Connect (OSTI)

    Mardaljevic, John; Heschong, Lisa; Lee, Eleanor

    2009-12-31

    The drive towards sustainable, low-energy buildings has increased the need for simple, yet accurate methods to evaluate whether a daylit building meets minimum standards for energy and human comfort performance. Current metrics do not account for the temporal and spatial aspects of daylight, nor of occupants comfort or interventions. This paper reviews the historical basis of current compliance methods for achieving daylit buildings, proposes a technical basis for development of better metrics, and provides two case study examples to stimulate dialogue on how metrics can be applied in a practical, real-world context.

  16. Energy Cost Calculator for Commercial Heat Pumps (5.4 >=< 20 Tons) |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Heat Pumps (5.4 >=< 20 Tons) Energy Cost Calculator for Commercial Heat Pumps (5.4 >=< 20 Tons) Vary equipment size, energy cost, hours of operation, and /or efficiency level. INPUT SECTION Input the following data (if any parameter is missing, calculator will set to default value). Defaults Project Type New Installation Replacement New Installation Condenser Type Air Source Water Source Air Source Existing Capacity * ton - Existing Cooling Efficiency * EER -

  17. Fluid Inclusion Gas Analysis

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Dilley, Lorie

    Fluid inclusion gas analysis for wells in various geothermal areas. Analyses used in developing fluid inclusion stratigraphy for wells and defining fluids across the geothermal fields. Each sample has mass spectrum counts for 180 chemical species.

  18. Fluid Inclusion Gas Analysis

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Dilley, Lorie

    2013-01-01

    Fluid inclusion gas analysis for wells in various geothermal areas. Analyses used in developing fluid inclusion stratigraphy for wells and defining fluids across the geothermal fields. Each sample has mass spectrum counts for 180 chemical species.

  19. U.S. Billion-Ton Update. Biomass Supply for a Bioenergy and Bioproducts Industry

    SciTech Connect (OSTI)

    none,

    2011-08-01

    This report is an update to the 2005 Billion-Ton Study that addresses shotcomings and questions that arose from the original report..

  20. Disposal Facility Reaches 15-Million-Ton Milestone | Department of Energy

    Office of Environmental Management (EM)

    Disposal Facility Reaches 15-Million-Ton Milestone Disposal Facility Reaches 15-Million-Ton Milestone July 30, 2013 - 12:00pm Addthis Matt McCormick, manager of the Richland Operations Office, commends a large group of Hanford workers for the 15-million-ton milestone at a public event at the Environmental Restoration Disposal Facility. Matt McCormick, manager of the Richland Operations Office, commends a large group of Hanford workers for the 15-million-ton milestone at a public event at the

  1. U.S. Billion-Ton Update: Biomass Supply for a Bioenergy and Bioproducts Industry

    Broader source: Energy.gov [DOE]

    An update to the 2005 report, "Biomass as a Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply"

  2. Removal of 1,082-Ton Reactor Among Richland Operations Office...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    from groundwater across the site ahead of schedule and pumped a record volume of water through treatment facilities to remove contamination, with more than 130 tons of...

  3. DOE-Sponsored Mississippi Project Hits 1-Million-Ton Milestone for Injected CO2

    Broader source: Energy.gov [DOE]

    A large-scale carbon dioxide storage project in Mississippi has become the fifth worldwide to reach the important milestone of more than 1 million tons injected.

  4. List of SEP Reporting Metrics

    Broader source: Energy.gov [DOE]

    DOE State Energy Program List of Reporting Metrics, which was produced by the Office of Energy Efficiency and Renewable Energy Weatherization and Intergovernmental Program for SEP and the Energy Efficiency and Conservation Block Grants (EECBG) programs.

  5. Common Carbon Metric | Open Energy Information

    Open Energy Info (EERE)

    Common Carbon Metric Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Common Carbon Metric AgencyCompany Organization: United Nations Environment Programme, World...

  6. Performance Metrics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Metrics Performance Metrics RCA & CAP Documents RCA/CAP Closure Report 2011 - This RCA/CAP Closure Report presents a status of the Department's initiatives to address the most significant issues and their corresponding root causes and officially closes out most of the issues and root causes Root Cause Analysis Report (RCA) 2008 - The Root Cause Analysis report identifies the key elements necessary to make the meaningful changes required to consistently deliver projects within cost and

  7. Buildings Performance Metrics Terminology | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Performance Metrics Terminology Buildings Performance Metrics Terminology This document provides the terms and definitions used in the Department of Energys Performance Metrics Research Project. PDF icon metrics_terminology_20090203.pdf More Documents & Publications Procuring Architectural and Engineering Services for Energy Efficiency and Sustainability Transmittal Letter for the Statewide Benchmarking Process Evaluation Guide for Benchmarking Residential Energy Efficiency Program

  8. Diversity and Inclusion

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Inclusion Diversity and Inclusion At Los Alamos, you will work with the best minds on the planet in an inclusive environment rich in intellectual vitality and opportunity for growth. African-American Partner Program African-American Partner Program African-American graduate interns help solve national challenges in their science, technology, engineering, or math disciplines. READ MORE Michael Torrez Employee Spotlight: Michael Torrez Research technologist enjoys spending his free time tracing

  9. Diversity and Inclusion Guidance

    Broader source: Energy.gov [DOE]

    All DOE diversity and inclusion policies, practices and programs must comply with Federal Equal Employment Opportunity laws, Merit Systems Principles, the foundation of the Civil Service, and not...

  10. Criticality safety review of 2 1/2 -, 10-, and 14-ton UF sub 6 cylinders

    SciTech Connect (OSTI)

    Broadhead, B.L.

    1991-01-01

    The US regulations governing the packaging and transportation of UF{sub 6} cylinders are contained in the publication 10CFR71. Under the current 10CFR71 regulations, packages are classified according to Fissile Class I, II, or III and a corresponding transport index (TI). UF{sub 6} cylinders designed to contain 2{1/2}-tons of UF{sub 6} are classified as Fissile Class II packages with a TI of 5 for the purpose of transportation. The 10-ton UF{sub 6} cylinders are classified as Fissile Class I with no TI assigned for transportation. The 14-ton cylinders are not certified for transport with enrichments greater than 1 wt % since they have no approved overpack. This work reviews the suitability of 2{1/2}-ton UF{sub 6} packages for reclassification as Fissile Class I with a maximum {sup 235}U enrichment of 5 wt %. Additionally, the 10- and 14-ton cylinders are reviewed to address a change in maximum {sup 235}U enrichment from 4.5 to 5 wt %. Based on this evaluation, the 2{1/2}-ton UF{sub 6} cylinders meet the 10CFR71 criteria for Fissile Class I packages, and no TI is needed for criticality safety purposes. Similarly, the 10- and 14-ton UF{sub 6} packages appear suitable for a maximum enrichment rating change to 5 wt % {sup 235}U. 6 refs., 4 figs., 1 tab.

  11. Why did they blow up 100 tons of TNT before the Trinity Test?

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Why did they blow up 100 tons of TNT before the Trinity Test? At the Bradbury Latest Issue:May 2016 all issues All Issues » submit Why did they blow up 100 tons of TNT before the Trinity Test? Science question of the month May 1, 2016 Sometimes people ask us a question and we try to answer them How do you calibrate instruments for a test that's never been done before? Great question. The 100-ton test was performed before the Trinity test to calibrate instruments prepared to explore the expected

  12. Photo of the Week: Smashing Atoms with 80-ton Magnets | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Smashing Atoms with 80-ton Magnets Photo of the Week: Smashing Atoms with 80-ton Magnets April 11, 2014 - 1:32pm Addthis The cyclotron, invented by Ernest Lawrence in the 1930s, is a unique circular particle accelerator, which Lawrence himself referred to as a "proton merry-go-round." In reality, the cyclotron specialized in smashing atoms. Part of this atom-smashing process requires very large, very heavy magnets -- sometimes weighing up to 220 tons. In this photo, workers

  13. Billion-Ton Update: Home-Grown Energy Resources Across the Nation |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Billion-Ton Update: Home-Grown Energy Resources Across the Nation Billion-Ton Update: Home-Grown Energy Resources Across the Nation August 11, 2011 - 3:59pm Addthis Total potential biomass resources by county in the contiguous U.S. from the baseline scenario of the Update (Figure 6.4, page 159) | Map from Billion-Ton Update Total potential biomass resources by county in the contiguous U.S. from the baseline scenario of the Update (Figure 6.4, page 159) | Map from

  14. Moab Project Disposes 2 Million Tons of Uranium Mill Tailings with Recovery Act Funds

    Broader source: Energy.gov [DOE]

    The Moab Uranium Mill Tailings Remedial Action Project reached its primary American Recovery and Reinvestment Act milestone ahead of schedule on Wednesday with the disposal of 2 million tons of...

  15. Hanford Landfill Reaches 15 Million Tons Disposed- Waste Disposal Mark Shows Success Cleaning Up River Corridor

    Broader source: Energy.gov [DOE]

    RICHLAND, Wash. – The U.S. Department of Energy (DOE) and its contractors have disposed of 15 million tons of contaminated material at the Environmental Restoration Disposal Facility (ERDF) since the facility began operations in 1996.

  16. DOE Moab Project Safely Removes 7 Million Tons of Mill Tailings

    Broader source: Energy.gov [DOE]

    (Grand Junction, CO) ― The U.S. Department of Energy (DOE) has safely moved another million tons of uranium mill tailings from the Moab site in Utah under the Uranium Mill Tailings Remedial Action Project.

  17. Long-term Decline of Aggregate Fuel Use per Cargo-ton-mile of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Long-term Decline of Aggregate Fuel Use per Cargo-ton-mile of Commercial Trucking; A Key Enabler of Expanded U.S. Trade and Economic Growth Poster presentation at the 2007 Diesel ...

  18. DOE Announces Webinars on Building a Billion Ton Bioeconomy and an

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Opportunity in Innovative Sensors | Department of Energy Building a Billion Ton Bioeconomy and an Opportunity in Innovative Sensors DOE Announces Webinars on Building a Billion Ton Bioeconomy and an Opportunity in Innovative Sensors May 5, 2016 - 9:06am Addthis EERE offers webinars to the public on a range of subjects, from adopting the latest energy efficiency and renewable energy technologies, to training for the clean energy workforce. Webinars are free; however, advanced registration is

  19. U.S. Manufacturers Save $1 Billion, 11 Million Tons of CO2 through Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Investments | Department of Energy Manufacturers Save $1 Billion, 11 Million Tons of CO2 through Energy Efficiency Investments U.S. Manufacturers Save $1 Billion, 11 Million Tons of CO2 through Energy Efficiency Investments September 25, 2013 - 12:00pm Addthis News Media Contact (202) 586-4940 WASHINGTON - Underscoring the Obama Administration's efforts to double energy productivity by 2030 and help businesses save money and energy, the Energy Department today recognized more than

  20. 1,153-ton Waste Vault Removed from 300 Area - Vault held waste tanks with

    Energy Savers [EERE]

    contamination from Hanford's former laboratory facilities | Department of Energy 1,153-ton Waste Vault Removed from 300 Area - Vault held waste tanks with contamination from Hanford's former laboratory facilities 1,153-ton Waste Vault Removed from 300 Area - Vault held waste tanks with contamination from Hanford's former laboratory facilities February 14, 2014 - 12:00pm Addthis Media Contacts Cameron Hardy, DOE 509-376-5365, Cameron.Hardy@rl.doe.gov Mark McKenna, Washington Closure

  1. Moab Mill Tailings Removal Project Reaches 5 Million Tons Disposed: Project

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Accomplishes Milestone While Doing it Safely | Department of Energy Moab Mill Tailings Removal Project Reaches 5 Million Tons Disposed: Project Accomplishes Milestone While Doing it Safely Moab Mill Tailings Removal Project Reaches 5 Million Tons Disposed: Project Accomplishes Milestone While Doing it Safely February 27, 2012 - 12:00pm Addthis Media Contacts Donald Metzler, Moab Federal Project Director, (970) 257-2115 Wendee Ryan, S&K Aerospace Public Affairs Manager, (970) 257-2145

  2. SO2907, A Putative TonB-dependent Receptor, Is Involved in Dissimilatory

    Office of Scientific and Technical Information (OSTI)

    Iron Reduction by Shewanella oneidensis Strain MR-1 (Journal Article) | SciTech Connect Journal Article: SO2907, A Putative TonB-dependent Receptor, Is Involved in Dissimilatory Iron Reduction by Shewanella oneidensis Strain MR-1 Citation Details In-Document Search Title: SO2907, A Putative TonB-dependent Receptor, Is Involved in Dissimilatory Iron Reduction by Shewanella oneidensis Strain MR-1 Shewanella oneidensis strain MR-1 utilizes soluble and insoluble ferric ions as terminal electron

  3. Definition of GPRA08 benefits metrics

    SciTech Connect (OSTI)

    None, None

    2009-01-18

    Background information for the FY 2007 GPRA methodology review on the definitions of GPRA08 benefits metrics.

  4. Module 6- Metrics, Performance Measurements and Forecasting

    Broader source: Energy.gov [DOE]

    This module reviews metrics such as cost and schedule variance along with cost and schedule performance indices.

  5. EECBG SEP Attachment 1 - Process metric list

    Energy Savers [EERE]

    EECBG 10-07B/SEP 10-006A Attachment 1: Process Metrics List Metric Area Metric Primary or Optional Metric Item(s) to Report On 1. Building Retrofits 1a. Buildings retrofitted, by sector Number of buildings retrofitted Square footage of buildings retrofitted 1b. Energy management systems installed, by sector Number of energy management systems installed Square footage of buildings under management 1c. Building roofs retrofitted, by sector Number of building roofs retrofitted Square footage of

  6. Multi-Metric Sustainability Analysis

    SciTech Connect (OSTI)

    Cowlin, S.; Heimiller, D.; Macknick, J.; Mann, M.; Pless, J.; Munoz, D.

    2014-12-01

    A readily accessible framework that allows for evaluating impacts and comparing tradeoffs among factors in energy policy, expansion planning, and investment decision making is lacking. Recognizing this, the Joint Institute for Strategic Energy Analysis (JISEA) funded an exploration of multi-metric sustainability analysis (MMSA) to provide energy decision makers with a means to make more comprehensive comparisons of energy technologies. The resulting MMSA tool lets decision makers simultaneously compare technologies and potential deployment locations.

  7. Western Resource Adequacy: Challenges - Approaches - Metrics | Department

    Energy Savers [EERE]

    of Energy Resource Adequacy: Challenges - Approaches - Metrics Western Resource Adequacy: Challenges - Approaches - Metrics West-Wide Resource Assessment Team. Committee on Regional Electric Power Cooperation. March 25, 2004 San Francisco, California PDF icon Western Resource Adequacy: Challenges - Approaches - Metrics More Documents & Publications Eastern Wind Integration and Transmission Study (EWITS) (Revised) Estimating the Benefits and Costs of Distributed Energy Technologies

  8. Diversity and Inclusion Related Documents

    Broader source: Energy.gov [DOE]

    The Office of Diversity and Inclusion fosters a diverse and inclusive work environment that ensures equality of opportunity for applicants and employees through Departmental diversity policy...

  9. Instructions for EM Corporate Performance Metrics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Instructions for EM Corporate Performance Metrics Instructions for EM Corporate Performance Metrics Quality Program Criteria PDF icon Instructions for EM Corporate Performance Metrics More Documents & Publications EM Corporate QA Performance Metrics CPMS Tables QA Corporate Board Meeting - July 2008

  10. Comparing Resource Adequacy Metrics: Preprint

    SciTech Connect (OSTI)

    Ibanez, E.; Milligan, M.

    2014-09-01

    As the penetration of variable generation (wind and solar) increases around the world, there is an accompanying growing interest and importance in accurately assessing the contribution that these resources can make toward planning reserve. This contribution, also known as the capacity credit or capacity value of the resource, is best quantified by using a probabilistic measure of overall resource adequacy. In recognizing the variable nature of these renewable resources, there has been interest in exploring the use of reliability metrics other than loss of load expectation. In this paper, we undertake some comparisons using data from the Western Electricity Coordinating Council in the western United States.

  11. Y-12's rough roads smoothed over with 23,000 tons of recycled asphalt |

    National Nuclear Security Administration (NNSA)

    National Nuclear Security Administration Home / Blog Y-12's rough roads smoothed over with 23,000 tons of recycled asphalt Tuesday, December 29, 2015 - 12:00am NNSA Blog Some 23,000 tons of asphalt removed during this summer's UPF site work have been put to use throughout the site. Potholes and gravel roads are now "paved" with the recycled asphalt that has been ground into a material called base course. Unlike gravel, the material tends to rebind into a solid form as it is packed

  12. Technical Workshop: Resilience Metrics for Energy Transmission...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon Henry H. Willis Presentation: Resilience Metrics for Energy Systems PDF icon Ross Guttromson Presentation: Energy Infrastructure Resilience: Framework and ...

  13. Efficient Synchronization Stability Metrics for Fault Clearing...

    Office of Scientific and Technical Information (OSTI)

    Title: Efficient Synchronization Stability Metrics for Fault Clearing Authors: Backhaus, Scott N. 1 ; Chertkov, Michael 1 ; Bent, Russell Whitford 1 ; Bienstock, Daniel 2...

  14. Microsoft Word - QER Resilience Metrics - Technical Workshp ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... of metrics for use in quantitative and qualitative analyses of transmission, distribution, ... leverage its efforts and resources to enable existing research to inform QER analysis. ...

  15. Microsoft Word - QER Resilience Metrics - Technical Workshp ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... New Energy Resilience Metrics - Ross Guttromson, Electric Power Systems ... Events of concern are relatively low probability but with potentially high consequences. ...

  16. Planning for the 400,000 tons/year AISI ironmaking demonstration plant

    SciTech Connect (OSTI)

    Aukrust, E. . AISI Direct Steelmaking Program)

    1993-01-01

    The American Iron and Steel Institute (AISI) has formulated a four-year program to design, construct, and operate a 400,000 net ton per year ironmaking demonstration plant. The plant will employ the coal-based ironmaking process developed under a 1989 cooperative agreement with DOE. AISI will manage the design and construction to be completed in the first two years and operate the plant for the second two years with a variety or ores, coals, and fluxes. Campaigns of increasing length are planned to optimize operations. After successful operation, the plant will be taken over by the host company. Results of studies to date indicate that, on a commercial scale, the AISI process will use 27% less energy and have variable operating costs $10 per ton lower and capital costs of $160 per annual ton, compared to the $250 per annual ton rebuild cost for the coke oven-blast furnace process it will replace. The process will enable the domestic steel industry to become more competitive by reducing its capital and operating cost. Furthermore, by eliminating the pollution problems associated with coke production and by completely enclosing the smelting reactions, this process represents a major step towards an environmentally friendly steel industry.

  17. FY 2014 Q3 Metric Summary | Department of Energy

    Energy Savers [EERE]

    4 Q3 Metric Summary FY 2014 Q3 Metric Summary FY 2014 Q3 Metric Summary PDF icon FY 2014 Q3 Metric Summary.pdf More Documents & Publications FY 2014 Overall Contract and Project Management Improvement Performance Metrics and Targets FY 2015 Overall Contract and Project Management Improvement Performance Metrics and Targets FY 2016 Overall Contract and Project Management Improvement Performance Metrics and Targets

  18. Smart Grid Status and Metrics Report Appendices

    SciTech Connect (OSTI)

    Balducci, Patrick J.; Antonopoulos, Chrissi A.; Clements, Samuel L.; Gorrissen, Willy J.; Kirkham, Harold; Ruiz, Kathleen A.; Smith, David L.; Weimar, Mark R.; Gardner, Chris; Varney, Jeff

    2014-07-01

    A smart grid uses digital power control and communication technology to improve the reliability, security, flexibility, and efficiency of the electric system, from large generation through the delivery systems to electricity consumers and a growing number of distributed generation and storage resources. To convey progress made in achieving the vision of a smart grid, this report uses a set of six characteristics derived from the National Energy Technology Laboratory Modern Grid Strategy. The Smart Grid Status and Metrics Report defines and examines 21 metrics that collectively provide insight into the grid’s capacity to embody these characteristics. This appendix presents papers covering each of the 21 metrics identified in Section 2.1 of the Smart Grid Status and Metrics Report. These metric papers were prepared in advance of the main body of the report and collectively form its informational backbone.

  19. How well will ton-scale dark matter direct detection experiments constrain minimal supersymmetry?

    SciTech Connect (OSTI)

    Akrami, Yashar; Savage, Christopher; Scott, Pat; Conrad, Jan; Edsj, Joakim E-mail: savage@fysik.su.se E-mail: conrad@fysik.su.se

    2011-04-01

    Weakly interacting massive particles (WIMPs) are amongst the most interesting dark matter (DM) candidates. Many DM candidates naturally arise in theories beyond the standard model (SM) of particle physics, like weak-scale supersymmetry (SUSY). Experiments aim to detect WIMPs by scattering, annihilation or direct production, and thereby determine the underlying theory to which they belong, along with its parameters. Here we examine the prospects for further constraining the Constrained Minimal Supersymmetric Standard Model (CMSSM) with future ton-scale direct detection experiments. We consider ton-scale extrapolations of three current experiments: CDMS, XENON and COUPP, with 1000 kg-years of raw exposure each. We assume energy resolutions, energy ranges and efficiencies similar to the current versions of the experiments, and include backgrounds at target levels. Our analysis is based on full likelihood constructions for the experiments. We also take into account present uncertainties on hadronic matrix elements for neutralino-quark couplings, and on halo model parameters. We generate synthetic data based on four benchmark points and scan over the CMSSM parameter space using nested sampling. We construct both Bayesian posterior PDFs and frequentist profile likelihoods for the model parameters, as well as the mass and various cross-sections of the lightest neutralino. Future ton-scale experiments will help substantially in constraining supersymmetry, especially when results of experiments primarily targeting spin-dependent nuclear scattering are combined with those directed more toward spin-independent interactions.

  20. Inclusive and Exclusive |Vub|

    SciTech Connect (OSTI)

    Petrella, Antonio; /Ferrara U. /INFN, Ferrara

    2011-11-17

    The current status of the determinations of CKM matrix element |V{sub ub}| via exclusive and inclusive charmless semileptonic B decays is reviewed. The large datasets collected at the B-Factories, and the increased precision of theoretical calculations have allowed an improvement in the determination of |V{sub ub}|. However, there are still significant uncertainties. In the exclusive approach, the most precise measurement of the pion channel branching ratio is obtained by an untagged analysis. This very good precision can be reached by tagged analyses with more data. The problem with exclusive decays is that the strong hadron dynamics can not be calculated from first principles and the determination of the form factor has to rely on light-cone sum rules or lattice QCD calculations. The current data samples allow a comparison of different FF models with data distributions. With further developments on lattice calculations, the theoretical error should shrink to reach the experimental one. The inclusive approach still provides the most precise |V{sub ub}| determinations. With new theoretical calculations, the mild (2.5{sigma}) discrepancy with respect to the |V{sub ub}| value determined from the global UT fit has been reduced. As in the exclusive approach, theoretical uncertainties represent the limiting factor to the precision of the measurement. Reducing the theoretical uncertainties to a level comparable with the statistical error is challenging. New measurements in semileptonic decays of charm mesons could increase the confidence in theoretical calculations and related uncertainties.

  1. Clean Cities Annual Metrics Report 2009 (Revised)

    SciTech Connect (OSTI)

    Johnson, C.

    2011-08-01

    Document provides Clean Cities coalition metrics about the use of alternative fuels; the deployment of alternative fuel vehicles, hybrid electric vehicles (HEVs), and idle reduction initiatives; fuel economy activities; and programs to reduce vehicle miles driven.

  2. Label-invariant Mesh Quality Metrics. (Conference) | SciTech...

    Office of Scientific and Technical Information (OSTI)

    Label-invariant Mesh Quality Metrics. Citation Details In-Document Search Title: Label-invariant Mesh Quality Metrics. Abstract not provided. Authors: Knupp, Patrick Publication ...

  3. Measuring solar reflectance Part I: Defining a metric that accurately...

    Office of Scientific and Technical Information (OSTI)

    I: Defining a metric that accurately predicts solar heat gain Citation Details In-Document Search Title: Measuring solar reflectance Part I: Defining a metric that accurately ...

  4. Business Metrics for High-Performance Homes: A Colorado Springs...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Business Metrics for High-Performance Homes: A Colorado Springs Case Study Citation Details In-Document Search Title: Business Metrics for High-Performance Homes: ...

  5. Methodologies for Reservoir Characterization Using Fluid Inclusion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Methodologies for Reservoir Characterization Using Fluid Inclusion Gas Chemistry Methodologies for Reservoir Characterization Using Fluid Inclusion Gas Chemistry Methodologies for ...

  6. Criticality Safety Review of 2 1/2-, 10-, and 14-Ton UF(Sub 6) Cylinders

    SciTech Connect (OSTI)

    Broadhead, B.L.

    1991-01-01

    Currently, UF{sub 6} cylinders designed to contain 2 1/2 tons of UF{sub 6} are classified as Fissile Class II packages with a transport index (TI) of 5 for the purpose of transportation. The 10-ton UF{sub 6} cylinders are classified as Fissile Class I with no TI assigned for transportation. The 14-ton cylinders, although not certified for transport with enrichments greater than 1 wt % because they have no approved overpack, can be used in on-site operations for enrichments greater than 1 wt %. The maximum 235U enrichments for these cylinders are 5.0 wt % for the 2 1/2-ton cylinder and 4.5 wt % for the 10- and 14-ton cylinders. This work reviews the suitability for reclassification of the 2 1/2-ton UF{sub 6} packages as Fissile Class I with a maximum {sup 235}U enrichment of 5 wt %. Additionally, the 10- and 14-ton cylinders are reviewed to address a change in maximum {sup 235}U enrichment from 4.5 to 5 wt %. Based on this evaluation, the 2 1/2-ton UF{sub 6} cylinders meet the 10 CFR.71 criteria for Fissile Class I packages, and no TI is needed for criticality safety purposes; however, a TI may be required based on radiation from the packages. Similarly, the 10- and 14-ton UF{sub 6} packages appear acceptable for a maximum enrichment rating change to 5 wt % {sup 235}U.

  7. Diversity & Inclusion | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8, 2015 Employee Spotlight: Muge Acik November 17, 2015 Employee Spotlight: Peter Friedman September 25, 2015 Diversity & Inclusion Argonne is home to a vibrant, diverse...

  8. U.S. Billion-Ton Update: Biomass Supply for a Bioenergy and Bioproducts Industry

    SciTech Connect (OSTI)

    Downing, Mark; Eaton, Laurence M; Graham, Robin Lambert; Langholtz, Matthew H; Perlack, Robert D; Turhollow Jr, Anthony F; Stokes, Bryce; Brandt, Craig C

    2011-08-01

    The report, Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply (generally referred to as the Billion-Ton Study or 2005 BTS), was an estimate of 'potential' biomass based on numerous assumptions about current and future inventory, production capacity, availability, and technology. The analysis was made to determine if conterminous U.S. agriculture and forestry resources had the capability to produce at least one billion dry tons of sustainable biomass annually to displace 30% or more of the nation's present petroleum consumption. An effort was made to use conservative estimates to assure confidence in having sufficient supply to reach the goal. The potential biomass was projected to be reasonably available around mid-century when large-scale biorefineries are likely to exist. The study emphasized primary sources of forest- and agriculture-derived biomass, such as logging residues, fuel treatment thinnings, crop residues, and perennially grown grasses and trees. These primary sources have the greatest potential to supply large, reliable, and sustainable quantities of biomass. While the primary sources were emphasized, estimates of secondary residue and tertiary waste resources of biomass were also provided. The original Billion-Ton Resource Assessment, published in 2005, was divided into two parts-forest-derived resources and agriculture-derived resources. The forest resources included residues produced during the harvesting of merchantable timber, forest residues, and small-diameter trees that could become available through initiatives to reduce fire hazards and improve forest health; forest residues from land conversion; fuelwood extracted from forests; residues generated at primary forest product processing mills; and urban wood wastes, municipal solid wastes (MSW), and construction and demolition (C&D) debris. For these forest resources, only residues, wastes, and small-diameter trees were considered. The 2005 BTS did not attempt to include any wood that would normally be used for higher-valued products (e.g., pulpwood) that could potentially shift to bioenergy applications. This would have required a separate economic analysis, which was not part of the 2005 BTS. The agriculture resources in the 2005 BTS included grains used for biofuels production; crop residues derived primarily from corn, wheat, and small grains; and animal manures and other residues. The cropland resource analysis also included estimates of perennial energy crops (e.g., herbaceous grasses, such as switchgrass, woody crops like hybrid poplar, as well as willow grown under short rotations and more intensive management than conventional plantation forests). Woody crops were included under cropland resources because it was assumed that they would be grown on a combination of cropland and pasture rather than forestland. In the 2005 BTS, current resource availability was estimated at 278 million dry tons annually from forestlands and slightly more than 194 million dry tons annually from croplands. These annual quantities increase to about 370 million dry tons from forestlands and to nearly 1 billion dry tons from croplands under scenario conditions of high-yield growth and large-scale plantings of perennial grasses and woody tree crops. This high-yield scenario reflects a mid-century timescale ({approx}2040-2050). Under conditions of lower-yield growth, estimated resource potential was projected to be about 320 and 580 million dry tons for forest and cropland biomass, respectively. As noted earlier, the 2005 BTS emphasized the primary resources (agricultural and forestry residues and energy crops) because they represent nearly 80% of the long-term resource potential. Since publication of the BTS in April 2005, there have been some rather dramatic changes in energy markets. In fact, just prior to the actual publication of the BTS, world oil prices started to increase as a result of a burgeoning worldwide demand and concerns about long-term supplies. By the end of the summer, oil prices topped $70 per barrel (bbl) and catastrophic hurricanes in the Gulf Coast shut down a significant fraction of U.S. refinery capacity. The following year, oil approached $80 per bbl due to supply concerns, as well as continued political tensions in the Middle East. The Energy Independence and Security Act of 2007 (EISA) was enacted in December of that year. By the end of December 2007, oil prices surpassed $100 per bbl for the first time, and by mid-summer 2008, prices approached $150 per bbl because of supply concerns, speculation, and weakness of the U.S. dollar. As fast as they skyrocketed, oil prices fell, and by the end of 2008, oil prices dropped below $50 per bbl, falling even more a month later due to the global economic recession. In 2009 and 2010, oil prices began to increase again as a result of a weak U.S. dollar and the rebounding of world economies.

  9. Occidental Chemical's Energy From Waste facility: 3,000,000 tons later

    SciTech Connect (OSTI)

    Blasins, G.F. )

    1988-01-01

    Occidental Chemical's Energy From Waste's cogeneration facility continues to be one of the most successful RDF plants in the U.S. The facility began operation in 1980 and was an operational success after a lengthy 2-1/2 year start-up and redesign, utilizing the air classification technology to produce RDF. In 1984, the plant was converted to a simplified shred and burn concept, significantly improving overall economics and viability of the operation. After processing 3.0 million tons the facility is a mature operation with a well developed experience base in long range operation and maintenance of the equipment utilized for processing and incinerating municipal solid waste.

  10. An ounce of prevention, a ton of cure | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    An ounce of prevention, a ... An ounce of prevention, a ton of cure Posted: June 24, 2015 - 3:11pm Aaron Spoon of Power Operations performs maintenance on 13.8 kV transformers 145 and 145A. Photo by Scott Fraker Y-12 recently saved time, taxpayer dollars, effort and potential injuries by taking a 72-hour planned simultaneous outage of power, steam and air systems. The weekend outage allowed a small army of Y-12 infrastructure, facilities and utilities workers to make repairs and perform

  11. Metrics for Evaluating the Accuracy of Solar Power Forecasting (Presentation)

    SciTech Connect (OSTI)

    Zhang, J.; Hodge, B.; Florita, A.; Lu, S.; Hamann, H.; Banunarayanan, V.

    2013-10-01

    This presentation proposes a suite of metrics for evaluating the performance of solar power forecasting.

  12. Enhanced Accident Tolerant LWR Fuels: Metrics Development

    SciTech Connect (OSTI)

    Shannon Bragg-Sitton; Lori Braase; Rose Montgomery; Chris Stanek; Robert Montgomery; Lance Snead; Larry Ott; Mike Billone

    2013-09-01

    The Department of Energy (DOE) Fuel Cycle Research and Development (FCRD) Advanced Fuels Campaign (AFC) is conducting research and development on enhanced Accident Tolerant Fuels (ATF) for light water reactors (LWRs). This mission emphasizes the development of novel fuel and cladding concepts to replace the current zirconium alloy-uranium dioxide (UO2) fuel system. The overall mission of the ATF research is to develop advanced fuels/cladding with improved performance, reliability and safety characteristics during normal operations and accident conditions, while minimizing waste generation. The initial effort will focus on implementation in operating reactors or reactors with design certifications. To initiate the development of quantitative metrics for ATR, a LWR Enhanced Accident Tolerant Fuels Metrics Development Workshop was held in October 2012 in Germantown, MD. This paper summarizes the outcome of that workshop and the current status of metrics development for LWR ATF.

  13. Metrics for comparison of crystallographic maps

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Urzhumtsev, Alexandre; Afonine, Pavel V.; Lunin, Vladimir Y.; Terwilliger, Thomas C.; Adams, Paul D.

    2014-10-01

    Numerical comparison of crystallographic contour maps is used extensively in structure solution and model refinement, analysis and validation. However, traditional metrics such as the map correlation coefficient (map CC, real-space CC or RSCC) sometimes contradict the results of visual assessment of the corresponding maps. This article explains such apparent contradictions and suggests new metrics and tools to compare crystallographic contour maps. The key to the new methods is rank scaling of the Fourier syntheses. The new metrics are complementary to the usual map CC and can be more helpful in map comparison, in particular when only some of their aspects,more » such as regions of high density, are of interest.« less

  14. EECBG SEP Attachment 1 - Process metric list | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SEP Attachment 1 - Process metric list EECBG SEP Attachment 1 - Process metric list Reporting Guidance Process Metric List PDF icon eecbg_10_07b_sep__10_006a_attachment1_process_metric_list.pdf More Documents & Publications EECBG 10-07C/SEP 10-006B Attachment 1: Process Metrics List EECBG Program Notice 10-07A DOE Recovery Act Reporting Requirements for the State Energy Program

  15. Table 4.8 Coal Demonstrated Reserve Base, January 1, 2011 (Billion Short Tons)

    U.S. Energy Information Administration (EIA) Indexed Site

    8 Coal Demonstrated Reserve Base, January 1, 2011 (Billion Short Tons) Region and State Anthracite Bituminous Coal Subbituminous Coal Lignite Total Underground Surface Underground Surface Underground Surface Surface 1 Underground Surface Total Appalachian 4.0 3.3 68.2 21.9 0.0 0.0 1.1 72.1 26.3 98.4 Alabama .0 .0 .9 2.1 .0 .0 1.1 .9 3.1 4.0 Kentucky, Eastern .0 .0 .8 9.1 .0 .0 .0 .8 9.1 9.8 Ohio .0 .0 17.4 5.7 .0 .0 .0 17.4 5.7 23.1 Pennsylvania 3.8 3.3 18.9 .8 .0 .0 .0 22.7 4.2 26.9 Virginia .1

  16. Table 7.2 Coal Production, 1949-2011 (Short Tons)

    U.S. Energy Information Administration (EIA) Indexed Site

    Coal Production, 1949-2011 (Short Tons) Year Rank Mining Method Location Total 1 Bituminous Coal 1 Subbituminous Coal Lignite Anthracite 1 Underground Surface 1 East of the Mississippi 1 West of the Mississippi 1 1949 437,868,000 [2] [2] 42,702,000 358,854,000 121,716,000 444,199,000 36,371,000 480,570,000 1950 516,311,000 [2] [2] 44,077,000 421,000,000 139,388,000 524,374,000 36,014,000 560,388,000 1951 533,665,000 [2] [2] 42,670,000 442,184,000 134,151,000 541,703,000 34,632,000 576,335,000

  17. Table 7.4 Coal Imports by Country of Origin, 2000-2011 (Short Tons)

    U.S. Energy Information Administration (EIA) Indexed Site

    Coal Imports by Country of Origin, 2000-2011 (Short Tons) Year Australia New Zealand Canada Mexico Colombia Venezuela China India Indonesia Europe South Africa Other Total Norway Poland Russia Ukraine United Kingdom Other Total 2000 167,595 0 1,923,434 6,671 7,636,614 2,038,774 19,646 205 718,149 0 0 1,212 0 238 0 1,450 0 85 12,512,623 2001 315,870 24,178 2,571,415 8,325 11,176,191 3,335,258 109,877 1,169 882,455 15,933 514,166 219,077 0 75,704 12 824,892 440,408 97,261 19,787,299 2002 821,280 0

  18. Table 7.5 Coal Exports by Country of Destination, 1960-2011 (Thousand Short Tons)

    U.S. Energy Information Administration (EIA) Indexed Site

    Coal Exports by Country of Destination, 1960-2011 (Thousand Short Tons) Year Canada Brazil Europe Japan Other 3 Total Belgium 1 Denmark France Germany 2 Italy Nether- lands Spain Turkey United Kingdom Other 3 Total 1960 12,843 1,067 1,116 130 794 4,566 4,899 2,837 331 NA – 2,440 17,113 5,617 1,341 37,981 1961 12,135 994 971 80 708 4,326 4,797 2,552 228 NA – 2,026 15,688 6,614 974 36,405 1962 12,302 1,327 1,289 38 851 5,056 5,978 3,320 766 NA 2 1,848 19,148 6,465 973 40,215 1963 14,557 1,161

  19. Table 7.7 Coal Mining Productivity, 1949-2011 (Short Tons per Employee Hour )

    U.S. Energy Information Administration (EIA) Indexed Site

    Coal Mining Productivity, 1949-2011 (Short Tons per Employee Hour 1) Year Mining Method Location Total 2 Underground Surface 2 East of the Mississippi West of the Mississippi Underground Surface 2 Total 2 Underground Surface 2 Total 2 1949 0.68 [3] 1.92 [3] NA NA NA NA NA NA 0.72 1950 .72 [3] 1.96 [3] NA NA NA NA NA NA .76 1951 .76 [3] 2.00 [3] NA NA NA NA NA NA .80 1952 .80 [3] 2.10 [3] NA NA NA NA NA NA .84 1953 .88 [3] 2.22 [3] NA NA NA NA NA NA .93 1954 1.00 [3] 2.48 [3] NA NA NA NA NA NA

  20. Table 7.8 Coke Overview, 1949-2011 (Thousand Short Tons)

    U.S. Energy Information Administration (EIA) Indexed Site

    Coke Overview, 1949-2011 (Thousand Short Tons) Year Production Trade Stock Change 2 Consumption 3 Imports Exports Net Imports 1 1949 63,637 279 548 -269 176 63,192 1950 72,718 438 398 40 -659 73,417 1951 79,331 162 1,027 -865 372 78,094 1952 68,254 313 792 -479 419 67,356 1953 78,837 157 520 -363 778 77,696 1954 59,662 116 388 -272 269 59,121 1955 75,302 126 531 -405 -1,248 76,145 1956 74,483 131 656 -525 634 73,324 1957 75,951 118 822 -704 814 74,433 1958 53,604 122 393 -271 675 52,658 1959

  1. Table 7.9 Coal Prices, 1949-2011 (Dollars per Short Ton)

    U.S. Energy Information Administration (EIA) Indexed Site

    Coal Prices, 1949-2011 (Dollars per Short Ton) Year Bituminous Coal Subbituminous Coal Lignite 1 Anthracite Total Nominal 2 Real 3 Nominal 2 Real 3 Nominal 2 Real 3 Nominal 2 Real 3 Nominal 2 Real 3 1949 4.90 [4] 33.80 [4,R] [4] [4] 2.37 16.35 [R] 8.90 61.38 [R] 5.24 36.14 [R] 1950 4.86 [4] 33.16 [4,R] [4] [4] 2.41 16.44 [R] 9.34 63.73 [R] 5.19 35.41 [R] 1951 4.94 [4] 31.44 [4,R] [4] [4] 2.44 15.53 [R] 9.94 63.26 [R] 5.29 33.67 [R] 1952 4.92 [4] 30.78 [4,R] [4] [4] 2.39 14.95 [R] 9.58 59.94 [R]

  2. Cracked lifting lug welds on ten-ton UF{sub 6} cylinders

    SciTech Connect (OSTI)

    Dorning, R.E.

    1991-12-31

    Ten-ton, Type 48X, UF{sub 6} cylinders are used at the Portsmouth Gaseous Diffusion Plant to withdraw enriched uranium hexafluoride from the cascade, transfer enriched uranium hexafluoride to customer cylinders, and feed enriched product to the cascade. To accomplish these activities, the cylinders are lifted by cranes and straddle carriers which engage the cylinder lifting lugs. In August of 1988, weld cracks on two lifting lugs were discovered during preparation to lift a cylinder. The cylinder was rejected and tagged out, and an investigating committee formed to determine the cause of cracking and recommend remedial actions. Further investigation revealed the problem may be general to this class of cylinder in this use cycle. This paper discusses the actions taken at the Portsmouth site to deal with the cracked lifting lug weld problem. The actions include inspection activities, interim corrective actions, metallurgical evaluation of cracked welds, weld repairs, and current monitoring/inspection program.

  3. Dynamic performance testing of prototype 3 ton air-cooled carrier absorption chiller

    SciTech Connect (OSTI)

    Borst, R.R.; Wood, B.D.

    1985-05-01

    The performance of a prototype 3 ton cooling capacity air-cooled lithium bromide/water absorption chiller was tested using an absorption chiller test facility which was modified to expand its testing capabilities to include air-cooled chillers in addition to water-cooled chillers. Temperatures of the three externally supplied fluid loops: hot water, chilled water, and cooling air, were varied in order to determine the effects this would have on the two principal measures of chiller performance: cooling capacity and thermal coefficient of performance (COP). A number of interrelated factors were identified as contributing to less than expected performance. For comparison, experimental correlations of other investigators for this and other similar absorption chillers are presented. These have been plotted as both contour and three-dimensional performance maps in order to more clearly show the functional dependence of the chiller performance on the fluid loop temperatures.

  4. Clean Cities 2011 Annual Metrics Report

    SciTech Connect (OSTI)

    Johnson, C.

    2012-12-01

    This report details the petroleum savings and vehicle emissions reductions achieved by the U.S. Department of Energy's Clean Cities program in 2011. The report also details other performance metrics, including the number of stakeholders in Clean Cities coalitions, outreach activities by coalitions and national laboratories, and alternative fuel vehicles deployed.

  5. Clean Cities 2010 Annual Metrics Report

    SciTech Connect (OSTI)

    Johnson, C.

    2012-10-01

    This report details the petroleum savings and vehicle emissions reductions achieved by the U.S. Department of Energy's Clean Cities program in 2010. The report also details other performance metrics, including the number of stakeholders in Clean Cities coalitions, outreach activities by coalitions and national laboratories, and alternative fuel vehicles deployed.

  6. Performance Metrics Research Project - Final Report

    SciTech Connect (OSTI)

    Deru, M.; Torcellini, P.

    2005-10-01

    NREL began work for DOE on this project to standardize the measurement and characterization of building energy performance. NREL's primary research objectives were to determine which performance metrics have greatest value for determining energy performance and to develop standard definitions and methods of measuring and reporting that performance.

  7. Diversity and Inclusion | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Inclusion Diversity and Inclusion Diversity and Inclusion The Office of Diversity and Inclusion fosters a diverse and inclusive work environment that ensures equality of opportunity for applicants and employees through Departmental diversity policy development, workforce analysis, outreach, retention, and education. We seek to capitalize on the diverse attributes of the nation today to build an inclusive Energy Department for tomorrow. The Energy Department strives to be the Federal government's

  8. Diversity and Inclusion | Careers | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Diversity and Inclusion NREL's world-class staff bring knowledge and expertise from across the globe. Our diverse backgrounds enable the laboratory to create clean energy solutions built upon a wide range of experiences and ideas. At NREL, we believe that fostering an inclusive work environment maximizes the unique talents of every NREL employee-regardless of race, sex, gender, religion, or nationality. Today's energy challenges are dynamic and far-reaching, and they demand greater integration

  9. Widget:CrazyEggMetrics | Open Energy Information

    Open Energy Info (EERE)

    CrazyEggMetrics Jump to: navigation, search This widget runs javascript code for the Crazy Egg user experience metrics. This should not be on all pages, but on select pages...

  10. Performance Metrics and Budget Division (HC-51) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Performance Metrics and Budget Division (HC-51) Performance Metrics and Budget Division (HC-51) MISSION: The mission of the Performance Metrics and Budget Division (HC-51) is to support the effective and efficient implementation of the Department of Energy's human capital initiatives and functions through the strategic integration of corporate human capital performance metrics and the budget of the Office of the Chief Human Capital Officer (HC). FUNCTIONS: Human capital performance measurement

  11. Financial Metrics Data Collection Protocol, Version 1.0

    SciTech Connect (OSTI)

    Fowler, Kimberly M.; Gorrissen, Willy J.; Wang, Na

    2010-04-30

    Brief description of data collection process and plan that will be used to collect financial metrics associated with sustainable design.

  12. Smart Grid Status and Metrics Report

    SciTech Connect (OSTI)

    Balducci, Patrick J.; Weimar, Mark R.; Kirkham, Harold

    2014-07-01

    To convey progress made in achieving the vision of a smart grid, this report uses a set of six characteristics derived from the National Energy Technology Laboratory Modern Grid Strategy. It measures 21 metrics to provide insight into the grid’s capacity to embody these characteristics. This report looks across a spectrum of smart grid concerns to measure the status of smart grid deployment and impacts.

  13. Performance and results of the LBNE 35 ton membrane cryostat prototype

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Montanari, David; Adamowski, Mark; Hahn, Alan; Norris, Barry; Reichenbacher, Juergen; Rucinski, Russell; Stewart, Jim; Tope, Terry

    2015-07-15

    We report on the performance and commissioning of the first membrane cryostat to be used for scientific application. The Long Baseline Neutrino Experiment (LBNE) has designed and fabricated a membrane cryostat prototype in collaboration with Ishikawajima-Harima Heavy Industries Co., Ltd. (IHI). LBNE has designed and fabricated the supporting cryogenic system infrastructure and successfully commissioned and operated the first membrane cryostat. Original goals of the prototype are: to demonstrate the membrane cryostat technology in terms of thermal performance, feasibility for liquid argon and leak tightness; to demonstrate that we can remove all the impurities from the vessel and achieve the puritymore » requirements in a membrane cryostat without evacuation; to demonstrate that we can achieve and maintain the purity requirements of the liquid argon using mol sieve and copper filters. The purity requirements of a large liquid argon detector such as LBNE are contaminants below 200 parts per trillion (ppt) oxygen equivalent. LBNE is planning the design and construction of a large liquid argon detector. This presentation will present requirements, design and construction of the LBNE 35 ton membrane cryostat prototype, and detail the commissioning and performance. The experience and results of this prototype are extremely important for the development of the LBNE detector.« less

  14. High temperature experiments on a 4 tons UF6 container TENERIFE program

    SciTech Connect (OSTI)

    Casselman, C.; Duret, B.; Seiler, J.M.; Ringot, C.; Warniez, P.

    1991-12-31

    The paper presents an experimental program (called TENERIFE) whose aim is to investigate the behaviour of a cylinder containing UF{sub 6} when exposed to a high temperature fire for model validation. Taking into account the experiments performed in the past, the modelization needs further information in order to be able to predict the behaviour of a real size cylinder when engulfed in a 800{degrees}C fire, as specified in the regulation. The main unknowns are related to (1) the UF{sub 6} behaviour beyond the critical point, (2) the relationship between temperature field and internal pressure and (3) the equivalent conductivity of the solid UF{sub 6}. In order to investigate these phenomena in a representative way it is foreseen to perform experiments with a cylinder of real diameter, but reduced length, containing 4 tons of UF{sub 6}. This cylinder will be placed in an electrically heated furnace. A confinement vessel prevents any dispersion of UF{sub 6}. The heat flux delivered by the furnace will be calibrated by specific tests. The cylinder will be changed for each test.

  15. 1000–ton testing machine for cyclic fatigue tests of materials at liquid nitrogen temperatures

    SciTech Connect (OSTI)

    Khitruk, A. A.; Klimchenko, Yu. A.; Kovalchuk, O. A.; Marushin, E. L.; Mednikov, A. A.; Nasluzov, S. N.; Privalova, E. K.; Rodin, I. Yu.; Stepanov, D. B.; Sukhanova, M. V.

    2014-01-29

    One of the main tasks of superconductive magnets R and D is to determine the mechanical and fatigue properties of structural materials and the critical design elements in the cryogenic temperature range. This paper describes a new facility built based on the industrial 1000-ton (10 MN) testing machine Schenk PC10.0S. Special equipment was developed to provide the mechanical and cyclic tensile fatigue tests of large-scale samples at the liquid nitrogen temperature and in a given load range. The main feature of the developed testing machine is the cryostat, in which the device converting a standard compression force of the testing machine to the tensile force affected at the test object is placed. The control system provides the remote control of the test and obtaining, processing and presentation of test data. As an example of the testing machine operation the test program and test results of the cyclic tensile fatigue tests of fullscale helium inlet sample of the PF1 coil ITER are presented.

  16. Performance and results of the LBNE 35 ton membrane cryostat prototype

    SciTech Connect (OSTI)

    Montanari, David; Adamowski, Mark; Hahn, Alan; Norris, Barry; Reichenbacher, Juergen; Rucinski, Russell; Stewart, Jim; Tope, Terry

    2015-07-15

    We report on the performance and commissioning of the first membrane cryostat to be used for scientific application. The Long Baseline Neutrino Experiment (LBNE) has designed and fabricated a membrane cryostat prototype in collaboration with Ishikawajima-Harima Heavy Industries Co., Ltd. (IHI). LBNE has designed and fabricated the supporting cryogenic system infrastructure and successfully commissioned and operated the first membrane cryostat. Original goals of the prototype are: to demonstrate the membrane cryostat technology in terms of thermal performance, feasibility for liquid argon and leak tightness; to demonstrate that we can remove all the impurities from the vessel and achieve the purity requirements in a membrane cryostat without evacuation; to demonstrate that we can achieve and maintain the purity requirements of the liquid argon using mol sieve and copper filters. The purity requirements of a large liquid argon detector such as LBNE are contaminants below 200 parts per trillion (ppt) oxygen equivalent. LBNE is planning the design and construction of a large liquid argon detector. This presentation will present requirements, design and construction of the LBNE 35 ton membrane cryostat prototype, and detail the commissioning and performance. The experience and results of this prototype are extremely important for the development of the LBNE detector.

  17. A Proposal for a Ton Scale Bubble Chamber for Dark Matter Detection

    SciTech Connect (OSTI)

    Collar, Juan; Dahl, C.Eric; Fustin, Drew; Robinson, Alan; Behnke, Ed; Behnke, Joshua; Breznau, William; Connor, Austin; Kuehnemund, Emily Grace; Levine, Ilan; Moan, Timothy; /Indiana U., South Bend /Fermilab

    2010-10-07

    The nature of non-baryonic dark matter is one of the most intriguing questions for particle physics at the start of the 21st century. There is ample evidence for its existence, but almost nothing is known of its properties. WIMPs are a very appealing candidate particle and several experimental campaigns are underway around the world to search for these particles via the nuclear recoils that they should induce. The COUPP series of bubble chambers has played a significant role in the WIMP search. Through a sequence of detectors of increasing size, a number of R&D issues have arisen and been solved, and the technology has now been advanced to the point where the construction of large chambers requires a modest research effort, some development, but mostly just engineering. It is within this context that we propose to build the next COUPP detector - COUPP-500, a ton scale device to be built over the next three years at Fermilab and then deployed deep underground at SNOLAB. The primary advantages of the COUPP approach over other technologies are: (1) The ability to reject electron and gamma backgrounds by arranging the chamber thermodynamics such that these particles do not even trigger the detector. (2) The ability to suppress neutron backgrounds by having the radioactively impure detection elements far from the active volume and by using the self-shielding of a large device and the high granularity to identify multiple bubbles. (3) The ability to build large chambers cheaply and with a choice of target fluids. (4) The ability to increase the size of the chambers without changing the size or complexity of the data acquisition. (5) Sensitivity to spin-dependent and spin-independent WIMP couplings. These key advantages should enable the goal of one background event in a ton-year of exposure to be achieved. The conceptual design of COUPP-500 is scaled from the preceding devices. In many cases all that is needed is a simple scaling up of components previously used. Calibration and R&D are still needed on some aspects of the system. We know we have the ability to distinguish alpha-induced events from nuclear recoils, but we do not yet know whether the combination of material purity and rejection are good enough to run for a year with no alpha background. We also need to have more detailed measurements of the detector threshold and a better understanding of its high gamma rejection. In addition, there are important checks to make on the longevity of the detector components in the hydraulic fluid and on the chemistry of the active fluid. The 2009 PASAG report explicitly supported the construction of the COUPP-500 device in all funding scenarios. The NSF has shown similar enthusiasm. It awarded one of its DUSEL S4 grants to assist in the engineering needed to build COUPP-500. The currently estimated cost of COUPP-500 is $8M, about half the $15M-$20M price tag expected by the PASAG report for a next generation dark matter search experiment. The COUPP-500 device will have a spin independent WIMP-nucleus cross-section sensitivity of 6 x 10{sup -47} cm{sup 2} after a background-free year of running. This device should then provide the benchmark against which all other WIMP searches are measured.

  18. Metrics For Comparing Plasma Mass Filters

    SciTech Connect (OSTI)

    Abraham J. Fetterman and Nathaniel J. Fisch

    2012-08-15

    High-throughput mass separation of nuclear waste may be useful for optimal storage, disposal, or environmental remediation. The most dangerous part of nuclear waste is the fission product, which produces most of the heat and medium-term radiation. Plasmas are well-suited to separating nuclear waste because they can separate many different species in a single step. A number of plasma devices have been designed for such mass separation, but there has been no standardized comparison between these devices. We define a standard metric, the separative power per unit volume, and derive it for three different plasma mass filters: the plasma centrifuge, Ohkawa filter, and the magnetic centrifugal mass filter. __________________________________________________

  19. Metrics for comparing plasma mass filters

    SciTech Connect (OSTI)

    Fetterman, Abraham J.; Fisch, Nathaniel J.

    2011-10-15

    High-throughput mass separation of nuclear waste may be useful for optimal storage, disposal, or environmental remediation. The most dangerous part of nuclear waste is the fission product, which produces most of the heat and medium-term radiation. Plasmas are well-suited to separating nuclear waste because they can separate many different species in a single step. A number of plasma devices have been designed for such mass separation, but there has been no standardized comparison between these devices. We define a standard metric, the separative power per unit volume, and derive it for three different plasma mass filters: the plasma centrifuge, Ohkawa filter, and the magnetic centrifugal mass filter.

  20. Metric redefinitions in Einstein-Aether theory

    SciTech Connect (OSTI)

    Foster, Brendan Z.

    2005-08-15

    'Einstein-Aether' theory, in which gravity couples to a dynamical, timelike, unit-norm vector field, provides a means for studying Lorentz violation in a generally covariant setting. Demonstrated here is the effect of a redefinition of the metric and 'aether' fields in terms of the original fields and two free parameters. The net effect is a change of the coupling constants appearing in the action. Using such a redefinition, one of the coupling constants can be set to zero, simplifying studies of solutions of the theory.

  1. Clean Cities 2013 Annual Metrics Report

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    3 Annual Metrics Report Caley Johnson and Mark Singer National Renewable Energy Laboratory Technical Report NREL/TP-5400-62838 October 2014 NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Operated by the Alliance for Sustainable Energy, LLC This report is available at no cost from the National Renewable Energy Laboratory (NREL) at www.nrel.gov/publications. Contract No. DE-AC36-08GO28308 National Renewable Energy Laboratory 15013

  2. Clean Cities 2014 Annual Metrics Report

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    4 Annual Metrics Report Caley Johnson and Mark Singer National Renewable Energy Laboratory Technical Report NREL/TP-5400-65265 December 2015 NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Operated by the Alliance for Sustainable Energy, LLC This report is available at no cost from the National Renewable Energy Laboratory (NREL) at www.nrel.gov/publications. Contract No. DE-AC36-08GO28308 National Renewable Energy Laboratory 15013

  3. Diversity and Inclusion redux | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Diversity and Inclusion redux Diversity and Inclusion redux February 11, 2015 You will recall that in the fall of 2015, I wrote a Montage about the intent to develop an Integrated Diversity and Inclusion program. The Diversity and Inclusion Council, under Chairpersons Mary Logue and Rolf Ent, has been working in collaboration with the Public Affairs office on several initiatives, which will soon go public. One of the very interesting but pernicious effects which, to a greater or lesser degree,

  4. Metrics for Measuring Progress Toward Implementation of the Smart Grid

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (June 2008) | Department of Energy Metrics for Measuring Progress Toward Implementation of the Smart Grid (June 2008) Metrics for Measuring Progress Toward Implementation of the Smart Grid (June 2008) Results of the breakout session discussions at the Smart Grid Implementation Workshop, June 19-20, 2008 PDF icon Metrics for Measuring Progress Toward Implementation of the Smart Grid More Documents & Publications 5th Annual CHP Roadmap Workshop Breakout Group Results, September 2004

  5. Integration of the EM Corporate QA Performance Metrics With Performance

    Energy Savers [EERE]

    Analysis Process | Department of Energy the EM Corporate QA Performance Metrics With Performance Analysis Process Integration of the EM Corporate QA Performance Metrics With Performance Analysis Process August 2009 Presenter: Robert Hinds, Savannah River Remediation, LLC Track 9-12 Topics Covered: Implementing CPMS for QA Corporate QA Performance Metrics Contractor Performance Analysis Contractor Assessment Programs Assessment Program Structure CPMS Integration with P/A Process Validating

  6. Technical Workshop: Resilience Metrics for Energy Transmission and

    Energy Savers [EERE]

    Distribution Infrastructure | Department of Energy Technical Workshop: Resilience Metrics for Energy Transmission and Distribution Infrastructure Technical Workshop: Resilience Metrics for Energy Transmission and Distribution Infrastructure During this workshop, EPSA invited technical experts from industry, national laboratories, academia, and NGOs to discuss the state of play of and need for resilience metrics and how they vary by natural gas, liquid fuels and electric grid infrastructures.

  7. EM Corporate QA Performance Metrics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    QA Corporate Board Meeting - November 2008 Instructions for EM Corporate Performance Metrics FY 2015 SENIOR EXECUTIVE SERVICE (SES) AND SENIOR PROFESSIONAL (SP) PERFORMANCE ...

  8. Conceptual Framework for Developing Resilience Metrics for the...

    Office of Environmental Management (EM)

    Metrics for the Electricity, Oil, and Gas Sectors in the United States (September ... Reliability to support the Office of Energy Policy and Systems Analysis in their writing ...

  9. Exploration Cost and Time Metric | Open Energy Information

    Open Energy Info (EERE)

    lt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":"" Hide Map Language: English Exploration Cost and Time Metric Screenshot References: Conference Paper1...

  10. Integration of the EM Corporate QA Performance Metrics With Performanc...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Integration of the EM Corporate QA Performance Metrics With Performance Analysis Process ... Assessment Program Structure CPMS Integration with PA Process Validating The Process ...

  11. DOE Announces Webinars on Solar Forecasting Metrics, the DOE...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Announces Webinars on Solar Forecasting Metrics, the DOE ... from adopting the latest energy efficiency and renewable ... to liquids technology, advantages of using natural gas, ...

  12. Wave Energy Converter System Requirements and Performance Metrics

    Broader source: Energy.gov [DOE]

    The Energy Department and Wave Energy Scotland are holding a joint workshop on wave energy converter (WEC) system requirements and performance metrics on Friday, February 26.

  13. Metrics correlation and analysis service (MCAS)

    SciTech Connect (OSTI)

    Baranovski, Andrew; Dykstra, Dave; Garzoglio, Gabriele; Hesselroth, Ted; Mhashilkar, Parag; Levshina, Tanya; /Fermilab

    2009-05-01

    The complexity of Grid workflow activities and their associated software stacks inevitably involves multiple organizations, ownership, and deployment domains. In this setting, important and common tasks such as the correlation and display of metrics and debugging information (fundamental ingredients of troubleshooting) are challenged by the informational entropy inherent to independently maintained and operated software components. Because such an information 'pond' is disorganized, it a difficult environment for business intelligence analysis i.e. troubleshooting, incident investigation and trend spotting. The mission of the MCAS project is to deliver a software solution to help with adaptation, retrieval, correlation, and display of workflow-driven data and of type-agnostic events, generated by disjoint middleware.

  14. Clean Cities 2014 Annual Metrics Report

    SciTech Connect (OSTI)

    Johnson, Caley; Singer, Mark

    2015-12-22

    Each year, the U.S. Department of Energy asks its Clean Cities program coordinators to submit annual reports of their activities and accomplishments for the previous calendar year. Data and information are submitted via an online database that is maintained as part of the Alternative Fuels Data Center (AFDC) at the National Renewable Energy Laboratory (NREL). Coordinators submit a range of data that characterize the membership, funding, projects, and activities of their coalitions. They also submit data about sales of alternative fuels, deployment of alternative fuel vehicles (AFVs) and hybrid electric vehicles (HEVs), idle-reduction (IR) initiatives, fuel economy activities, and programs to reduce vehicle miles traveled (VMT). NREL analyzes the data and translates them into petroleum-use reduction impacts, which are summarized in this 2014 Annual Metrics Report.

  15. Clean Cities 2013 Annual Metrics Report

    SciTech Connect (OSTI)

    Johnson, C.; Singer, M.

    2014-10-01

    Each year, the U.S. Department of Energy asks its Clean Cities program coordinators to submit annual reports of their activities and accomplishments for the previous calendar year. Data and information are submitted via an online database that is maintained as part of the Alternative Fuels Data Center (AFDC) at the National Renewable Energy Laboratory (NREL). Coordinators submit a range of data that characterize the membership, funding, projects, and activities of their coalitions. They also submit data about sales of alternative fuels, deployment of alternative fuel vehicles (AFVs) and hybrid electric vehicles (HEVs), idle-reduction (IR) initiatives, fuel economy activities, and programs to reduce vehicle miles traveled (VMT). NREL analyzes the data and translates them into petroleum-use reduction impacts, which are summarized in this 2013 Annual Metrics Report.

  16. Metrics for Evaluating Conventional and Renewable Energy Technologies (Presentation)

    SciTech Connect (OSTI)

    Mann, M. K.

    2013-01-01

    With numerous options for the future of natural gas, how do we know we're going down the right path? How do we designate a metric to measure and demonstrate change and progress, and how does that metric incorporate all stakeholders and scenarios?

  17. Practical Diagnostics for Evaluating Residential Commissioning Metrics

    SciTech Connect (OSTI)

    Wray, Craig; Walker, Iain; Siegel, Jeff; Sherman, Max

    2002-06-11

    In this report, we identify and describe 24 practical diagnostics that are ready now to evaluate residential commissioning metrics, and that we expect to include in the commissioning guide. Our discussion in the main body of this report is limited to existing diagnostics in areas of particular concern with significant interactions: envelope and HVAC systems. These areas include insulation quality, windows, airtightness, envelope moisture, fan and duct system airflows, duct leakage, cooling equipment charge, and combustion appliance backdrafting with spillage. Appendix C describes the 83 other diagnostics that we have examined in the course of this project, but that are not ready or are inappropriate for residential commissioning. Combined with Appendix B, Table 1 in the main body of the report summarizes the advantages and disadvantages of all 107 diagnostics. We first describe what residential commissioning is, its characteristic elements, and how one might structure its process. Our intent in this discussion is to formulate and clarify these issues, but is largely preliminary because such a practice does not yet exist. Subsequent sections of the report describe metrics one can use in residential commissioning, along with the consolidated set of 24 practical diagnostics that the building industry can use now to evaluate them. Where possible, we also discuss the accuracy and usability of diagnostics, based on recent laboratory work and field studies by LBNL staff and others in more than 100 houses. These studies concentrate on evaluating diagnostics in the following four areas: the DeltaQ duct leakage test, air-handler airflow tests, supply and return grille airflow tests, and refrigerant charge tests. Appendix A describes those efforts in detail. In addition, where possible, we identify the costs to purchase diagnostic equipment and the amount of time required to conduct the diagnostics. Table 1 summarizes these data. Individual equipment costs for the 24 practical diagnostics range from a few hundred dollars to many thousands of dollars. The higher costs are associated with infrared thermography and state-of-the-art automated diagnostic systems. Most tests can be performed in one hour or less, using equipment priced toward the lower end of the cost spectrum.

  18. Self-benchmarking Guide for Data Centers: Metrics, Benchmarks, Actions

    SciTech Connect (OSTI)

    Mathew, Paul; Ganguly, Srirupa; Greenberg, Steve; Sartor, Dale

    2009-07-13

    This guide describes energy efficiency metrics and benchmarks that can be used to track the performance of and identify potential opportunities to reduce energy use in data centers. This guide is primarily intended for personnel who have responsibility for managing energy use in existing data centers - including facilities managers, energy managers, and their engineering consultants. Additionally, data center designers may also use the metrics and benchmarks described in this guide for goal-setting in new construction or major renovation. This guide provides the following information: (1) A step-by-step outline of the benchmarking process. (2) A set of performance metrics for the whole building as well as individual systems. For each metric, the guide provides a definition, performance benchmarks, and potential actions that can be inferred from evaluating this metric. (3) A list and descriptions of the data required for computing the metrics. This guide is complemented by spreadsheet templates for data collection and for computing the benchmarking metrics. This guide builds on prior data center benchmarking studies supported by the California Energy Commission. Much of the benchmarking data are drawn from the LBNL data center benchmarking database that was developed from these studies. Additional benchmark data were obtained from engineering experts including facility designers and energy managers. This guide also builds on recent research supported by the U.S. Department of Energy's Save Energy Now program.

  19. Self-benchmarking Guide for Cleanrooms: Metrics, Benchmarks, Actions

    SciTech Connect (OSTI)

    Mathew, Paul; Sartor, Dale; Tschudi, William

    2009-07-13

    This guide describes energy efficiency metrics and benchmarks that can be used to track the performance of and identify potential opportunities to reduce energy use in laboratory buildings. This guide is primarily intended for personnel who have responsibility for managing energy use in existing laboratory facilities - including facilities managers, energy managers, and their engineering consultants. Additionally, laboratory planners and designers may also use the metrics and benchmarks described in this guide for goal-setting in new construction or major renovation. This guide provides the following information: (1) A step-by-step outline of the benchmarking process. (2) A set of performance metrics for the whole building as well as individual systems. For each metric, the guide provides a definition, performance benchmarks, and potential actions that can be inferred from evaluating this metric. (3) A list and descriptions of the data required for computing the metrics. This guide is complemented by spreadsheet templates for data collection and for computing the benchmarking metrics. This guide builds on prior research supported by the national Laboratories for the 21st Century (Labs21) program, supported by the U.S. Department of Energy and the U.S. Environmental Protection Agency. Much of the benchmarking data are drawn from the Labs21 benchmarking database and technical guides. Additional benchmark data were obtained from engineering experts including laboratory designers and energy managers.

  20. Self-benchmarking Guide for Laboratory Buildings: Metrics, Benchmarks, Actions

    SciTech Connect (OSTI)

    Mathew, Paul; Greenberg, Steve; Sartor, Dale

    2009-07-13

    This guide describes energy efficiency metrics and benchmarks that can be used to track the performance of and identify potential opportunities to reduce energy use in laboratory buildings. This guide is primarily intended for personnel who have responsibility for managing energy use in existing laboratory facilities - including facilities managers, energy managers, and their engineering consultants. Additionally, laboratory planners and designers may also use the metrics and benchmarks described in this guide for goal-setting in new construction or major renovation. This guide provides the following information: (1) A step-by-step outline of the benchmarking process. (2) A set of performance metrics for the whole building as well as individual systems. For each metric, the guide provides a definition, performance benchmarks, and potential actions that can be inferred from evaluating this metric. (3) A list and descriptions of the data required for computing the metrics. This guide is complemented by spreadsheet templates for data collection and for computing the benchmarking metrics. This guide builds on prior research supported by the national Laboratories for the 21st Century (Labs21) program, supported by the U.S. Department of Energy and the U.S. Environmental Protection Agency. Much of the benchmarking data are drawn from the Labs21 benchmarking database and technical guides. Additional benchmark data were obtained from engineering experts including laboratory designers and energy managers.

  1. NMR Spectroscopic Investigation of Inclusion Complexes between...

    Office of Scientific and Technical Information (OSTI)

    NMR Spectroscopic Investigation of Inclusion Complexes between Cyclodextrins and the Neurotoxin Tetramethylenedisulfotetramine (TETS) Citation Details In-Document Search Title: NMR ...

  2. DISPLAYING AND INTERPRETING FLUID INCLUSION STRATIGRAPHY ANALYSES...

    Open Energy Info (EERE)

    DISPLAYING AND INTERPRETING FLUID INCLUSION STRATIGRAPHY ANALYSES ON MUDLOG GRAPHS Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Proceedings:...

  3. ARM - Evaluation Product - AERI Data Quality Metric (AERI-QC...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send Evaluation Product : AERI Data Quality Metric (AERI-QC) Ancillary NetCDF file to be used with the...

  4. Microsoft Word - followup to Fin Risk Metrics workshop.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    March 21, 2008 PurposeSubject: Follow-up to Financial Risk Metrics Workshop Page 1 of 1 Differences in Cash Flow between Net Billing and Direct Pay for Energy Northwest Attached...

  5. A Graph Analytic Metric for Mitigating Advanced Persistent Threat

    SciTech Connect (OSTI)

    Johnson, John R.; Hogan, Emilie A.

    2013-06-04

    This paper introduces a novel graph analytic metric that can be used to measure the potential vulnerability of a cyber network to specific types of attacks that use lateral movement and privilege escalation such as the well known Pass The Hash, (PTH). The metric is computed from an oriented subgraph of the underlying cyber network induced by selecting only those edges for which a given property holds between the two vertices of the edge. The metric with respect to a select node on the subgraph is defined as the likelihood that the select node is reachable from another arbitrary node in the graph. This metric can be calculated dynamically from the authorization and auditing layers during the network security authorization phase and will potentially enable predictive deterrence against attacks such as PTH.

  6. ARM - Evaluation Product - Barrow Radiation Data (2009 metric...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    from you Send us a note below or call us at 1-888-ARM-DATA. Send Evaluation Product : Barrow Radiation Data (2009 metric) Observations from a suite of radiometers including...

  7. Integration of Sustainability Metrics into Design Cases and State...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bioenergy Technologies Office (BETO) 2015 Project Peer Review Integration of Sustainability Metrics into Design Cases and State of Technology Assessments 2.1.0.1002.1.0.302 NREL ...

  8. Resilient Control Systems Practical Metrics Basis for Defining Mission Impact

    SciTech Connect (OSTI)

    Craig G. Rieger

    2014-08-01

    "Resilience” describes how systems operate at an acceptable level of normalcy despite disturbances or threats. In this paper we first consider the cognitive, cyber-physical interdependencies inherent in critical infrastructure systems and how resilience differs from reliability to mitigate these risks. Terminology and metrics basis are provided to integrate the cognitive, cyber-physical aspects that should be considered when defining solutions for resilience. A practical approach is taken to roll this metrics basis up to system integrity and business case metrics that establish “proper operation” and “impact.” A notional chemical processing plant is the use case for demonstrating how the system integrity metrics can be applied to establish performance, and

  9. Measuring solar reflectance Part I: Defining a metric that accurately...

    Office of Scientific and Technical Information (OSTI)

    A widely used solar reflectance metric based on the ASTM Standard E891 beam-normal solar spectral irradiance underestimates the solar heat gain of a spectrally selective 'cool ...

  10. EVMS Training Snippet: 3.2 Schedule Health Metrics

    Broader source: Energy.gov [DOE]

    This EVMS Training Snippet sponsored by the Office of Project Management (PM) focuses on ‘what’ the metrics are, ‘why’ they are important, and what they tell us about the schedule health. This...

  11. Analysis of Solar Cell Quality Using Voltage Metrics: Preprint

    SciTech Connect (OSTI)

    Toberer, E. S.; Tamboli, A. C.; Steiner, M.; Kurtz, S.

    2012-06-01

    The highest efficiency solar cells provide both excellent voltage and current. Of these, the open-circuit voltage (Voc) is more frequently viewed as an indicator of the material quality. However, since the Voc also depends on the band gap of the material, the difference between the band gap and the Voc is a better metric for comparing material quality of unlike materials. To take this one step further, since Voc also depends on the shape of the absorption edge, we propose to use the ultimate metric: the difference between the measured Voc and the Voc calculated from the external quantum efficiency using a detailed balance approach. This metric is less sensitive to changes in cell design and definition of band gap. The paper defines how to implement this metric and demonstrates how it can be useful in tracking improvements in Voc, especially as Voc approaches its theoretical maximum.

  12. NMR Spectroscopic Investigation of Inclusion Complexes between

    Office of Scientific and Technical Information (OSTI)

    Cyclodextrins and the Neurotoxin Tetramethylenedisulfotetramine (TETS) (Journal Article) | SciTech Connect Journal Article: NMR Spectroscopic Investigation of Inclusion Complexes between Cyclodextrins and the Neurotoxin Tetramethylenedisulfotetramine (TETS) Citation Details In-Document Search Title: NMR Spectroscopic Investigation of Inclusion Complexes between Cyclodextrins and the Neurotoxin Tetramethylenedisulfotetramine (TETS) Authors: Mayer, B P ; Albo, R F ; Hok, S ; Valdez, C A

  13. Conceptual Framework for Developing Resilience Metrics for the Electricity,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Oil, and Gas Sectors in the United States (September 2015) | Department of Energy Conceptual Framework for Developing Resilience Metrics for the Electricity, Oil, and Gas Sectors in the United States (September 2015) Conceptual Framework for Developing Resilience Metrics for the Electricity, Oil, and Gas Sectors in the United States (September 2015) This report has been written for the Department of Energy's Office of Electricity Delivery and Energy Reliability to support the Office of

  14. New IEC Specifications Help Define Wind Plant Performance Reporting Metrics

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy IEC Specifications Help Define Wind Plant Performance Reporting Metrics New IEC Specifications Help Define Wind Plant Performance Reporting Metrics January 6, 2014 - 10:00am Addthis This is an excerpt from the Fourth Quarter 2013 edition of the Wind Program R&D Newsletter. The U.S. Department of Energy Wind Program and Sandia National Laboratories have been working with the International Electrotechnical Commission (IEC) Committee on wind turbine availability to

  15. Weatherization Assistance Program Goals and Metrics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Goals and Metrics Weatherization Assistance Program Goals and Metrics UT - Bettelle - Oak Ridge National Laboratory Logo The U.S. Department of Energy (DOE) Weatherization Assistance Program (WAP) regularly reviews the work of states and grant recipients for effectiveness and for meeting program goals. DOE's Oak Ridge National Laboratory provides technical support to the program and conducts the evaluations. Goals The overall goal of WAP is to reduce the burden of energy prices on the

  16. Taking out 1 billion tons of CO2: The magic of China's 11th Five-Year Plan?

    SciTech Connect (OSTI)

    Zhou, Nan; Lin, Jiang; Zhou, Nan; Levine, Mark; Fridley, David

    2007-07-01

    China's 11th Five-Year Plan (FYP) sets an ambitious target for energy-efficiency improvement: energy intensity of the country's gross domestic product (GDP) should be reduced by 20% from 2005 to 2010 (NDRC, 2006). This is the first time that a quantitative and binding target has been set for energy efficiency, and signals a major shift in China's strategic thinking about its long-term economic and energy development. The 20% energy intensity target also translates into an annual reduction of over 1.5 billion tons of CO2 by 2010, making the Chinese effort one of most significant carbon mitigation effort in the world today. While it is still too early to tell whether China will achieve this target, this paper attempts to understand the trend in energy intensity in China and to explore a variety of options toward meeting the 20% target using a detailed end-use energy model.

  17. Methods and results for stress analyses on 14-ton, thin-wall depleted UF{sub 6} cylinders

    SciTech Connect (OSTI)

    Kirkpatrick, J.R.; Chung, C.K.; Frazier, J.L.; Kelley, D.K.

    1996-10-01

    Uranium enrichment operations at the three US gaseous diffusion plants produce depleted uranium hexafluoride (DUF{sub 6}) as a residential product. At the present time, the inventory of DUF{sub 6} in this country is more than half a million tons. The inventory of DUF{sub 6} is contained in metal storage cylinders, most of which are located at the gaseous diffusion plants. The principal objective of the project is to ensure the integrity of the cylinders to prevent causing an environmental hazard by releasing the contents of the cylinders into the atmosphere. Another objective is to maintain the cylinders in such a manner that the DUF{sub 6} may eventually be converted to a less hazardous material for final disposition. An important task in the DUF{sub 6} cylinders management project is determining how much corrosion of the walls can be tolerated before the cylinders are in danger of being damaged during routine handling and shipping operations. Another task is determining how to handle cylinders that have already been damaged in a manner that will minimize the chance that a breach will occur or that the size of an existing breach will be significantly increased. A number of finite element stress analysis (FESA) calculations have been done to analyze the stresses for three conditions: (1) while the cylinder is being lifted, (2) when a cylinder is resting on two cylinders under it in the customary two-tier stacking array, and (3) when a cylinder is resting on tis chocks on the ground. Various documents describe some of the results and discuss some of the methods whereby they have been obtained. The objective of the present report is to document as many of the FESA cases done at Oak Ridge for 14-ton thin-wall cylinders as possible, giving results and a description of the calculations in some detail.

  18. Diversity & Inclusion at Argonne | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Diversity & Inclusion at Argonne Share Duration 2:50 Topic Operations Human Resources Diversity Argonne Diversity & Inclusion Advisory Council members discuss the value and importance of a diverse and inclusive workplace

  19. Metrics Evolution in an Energy Research & Development Program

    SciTech Connect (OSTI)

    Brent Dixon

    2011-08-01

    All technology programs progress through three phases: Discovery, Definition, and Deployment. The form and application of program metrics needs to evolve with each phase. During the discovery phase, the program determines what is achievable. A set of tools is needed to define program goals, to analyze credible technical options, and to ensure that the options are compatible and meet the program objectives. A metrics system that scores the potential performance of technical options is part of this system of tools, supporting screening of concepts and aiding in the overall definition of objectives. During the definition phase, the program defines what specifically is wanted. What is achievable is translated into specific systems and specific technical options are selected and optimized. A metrics system can help with the identification of options for optimization and the selection of the option for deployment. During the deployment phase, the program shows that the selected system works. Demonstration projects are established and classical systems engineering is employed. During this phase, the metrics communicate system performance. This paper discusses an approach to metrics evolution within the Department of Energy's Nuclear Fuel Cycle R&D Program, which is working to improve the sustainability of nuclear energy.

  20. Diversity and Inclusion | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Diversity and Inclusion Argonne is home to a vibrant, diverse community. When we bring together groups of people whose cultural and intellectual backgrounds equip them to look at a...

  1. Integrated Diversity and Inclusion Management! | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Integrated Diversity and Inclusion Management! Integrated Diversity and Inclusion Management! September 8, 2015 Those of us who are moderately long in the tooth remember the bad old days of (un)safety. One occasion that I recall involved siphoning liquid scintillator with a rubber tube and a mouth, mine. Another was the inappropriate use of magnetic tools in a magnetic field. All that has changed; we are now proud of a safety record and performance, which limits the accidents that do damage to

  2. Diversity & Inclusion FAQs | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FAQs Q. How does diversity and inclusion fit with Argonne's values? A. Argonne values excellence in science and engineering, and it values the contributions that individuals make. The lab strongly encourages collaboration for the simple reason that scientific innovation is more likely to occur when individuals with diverse viewpoints, approaches, methodologies and backgrounds work together to solve a problem. In this, our collective diversity and an inclusive culture add value to scientific

  3. Government-Wide Diversity and Inclusion Strategic Plan (2011...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Government-Wide Diversity and Inclusion Strategic Plan (2011), Office of Personnel Management Government-Wide Diversity and Inclusion Strategic Plan (2011), Office of Personnel ...

  4. Metrics for Evaluating the Accuracy of Solar Power Forecasting: Preprint

    SciTech Connect (OSTI)

    Zhang, J.; Hodge, B. M.; Florita, A.; Lu, S.; Hamann, H. F.; Banunarayanan, V.

    2013-10-01

    Forecasting solar energy generation is a challenging task due to the variety of solar power systems and weather regimes encountered. Forecast inaccuracies can result in substantial economic losses and power system reliability issues. This paper presents a suite of generally applicable and value-based metrics for solar forecasting for a comprehensive set of scenarios (i.e., different time horizons, geographic locations, applications, etc.). In addition, a comprehensive framework is developed to analyze the sensitivity of the proposed metrics to three types of solar forecasting improvements using a design of experiments methodology, in conjunction with response surface and sensitivity analysis methods. The results show that the developed metrics can efficiently evaluate the quality of solar forecasts, and assess the economic and reliability impact of improved solar forecasting.

  5. Non-minimal derivative couplings of the composite metric

    SciTech Connect (OSTI)

    Heisenberg, Lavinia

    2015-11-04

    In the context of massive gravity, bi-gravity and multi-gravity non-minimal matter couplings via a specific composite effective metric were investigated recently. Even if these couplings generically reintroduce the Boulware-Deser ghost, this composite metric is unique in the sense that the ghost reemerges only beyond the decoupling limit and the matter quantum loop corrections do not detune the potential interactions. We consider non-minimal derivative couplings of the composite metric to matter fields for a specific subclass of Horndeski scalar-tensor interactions. We first explore these couplings in the mini-superspace and investigate in which scenario the ghost remains absent. We further study these non-minimal derivative couplings in the decoupling-limit of the theory and show that the equation of motion for the helicity-0 mode remains second order in derivatives. Finally, we discuss preliminary implications for cosmology.

  6. Calabi-Yau metrics for quotients and complete intersections

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Braun, Volker; Brelidze, Tamaz; Douglas, Michael R.; Ovrut, Burt A.

    2008-05-22

    We extend previous computations of Calabi-Yau metrics on projective hypersurfaces to free quotients, complete intersections, and free quotients of complete intersections. In particular, we construct these metrics on generic quintics, four-generation quotients of the quintic, Schoen Calabi-Yau complete intersections and the quotient of a Schoen manifold with Z₃ x Z₃ fundamental group that was previously used to construct a heterotic standard model. Various numerical investigations into the dependence of Donaldson's algorithm on the integration scheme, as well as on the Kähler and complex structure moduli, are also performed.

  7. Primer Control System Cyber Security Framework and Technical Metrics

    SciTech Connect (OSTI)

    Wayne F. Boyer; Miles A. McQueen

    2008-05-01

    The Department of Homeland Security National Cyber Security Division supported development of a control system cyber security framework and a set of technical metrics to aid owner-operators in tracking control systems security. The framework defines seven relevant cyber security dimensions and provides the foundation for thinking about control system security. Based on the developed security framework, a set of ten technical metrics are recommended that allow control systems owner-operators to track improvements or degradations in their individual control systems security posture.

  8. Culture, and a Metrics Methodology for Biological Countermeasure Scenarios

    SciTech Connect (OSTI)

    Simpson, Mary J.

    2007-03-15

    Outcome Metrics Methodology defines a way to evaluate outcome metrics associated with scenario analyses related to biological countermeasures. Previous work developed a schema to allow evaluation of common elements of impacts across a wide range of potential threats and scenarios. Classes of metrics were identified that could be used by decision makers to differentiate the common bases among disparate scenarios. Typical impact metrics used in risk calculations include the anticipated number of deaths, casualties, and the direct economic costs should a given event occur. There are less obvious metrics that are often as important and require more intensive initial work to be incorporated. This study defines a methodology for quantifying, evaluating, and ranking metrics other than direct health and economic impacts. As has been observed with the consequences of Hurricane Katrina, impacts to the culture of specific sectors of society are less obvious on an immediate basis but equally important over the ensuing and long term. Culture is used as the example class of metrics within which • requirements for a methodology are explored • likely methodologies are examined • underlying assumptions for the respective methodologies are discussed • the basis for recommending a specific methodology is demonstrated. Culture, as a class of metrics, is shown to consist of political, sociological, and psychological elements that are highly valued by decision makers. In addition, cultural practices, dimensions, and kinds of knowledge offer complementary sets of information that contribute to the context within which experts can provide input. The quantification and evaluation of sociopolitical, socio-economic, and sociotechnical impacts depend predominantly on subjective, expert judgment. Epidemiological data is limited, resulting in samples with statistical limits. Dose response assessments and curves depend on the quality of data and its relevance to human modes of exposure. With uncertain data and limited common units, the aggregation of results is not inherently obvious. Candidate methodologies discussed include statistical, analytical, and expert-based numerical approaches. Most statistical methods require large amounts of data with a random distribution of values for validity. Analytical methods predominate wherein structured data or patterns are evident and randomness is low. The analytical hierarchy process is shown to satisfy all requirements and provide a detailed method for measurement that depends on expert judgment by decision makers.

  9. Chemical reactions of UF{sub 6} with water on ingress to damaged model 48X 10 ton cylinder

    SciTech Connect (OSTI)

    Rothman, A.B.

    1996-02-01

    Chemistry studies of the effects of water flooding in Model 48X 10-ton UF{sub 6} storage cylinders, as a result of impact fractures, were conducted to support the Safety Analysis Report for Packaging (SARP) review of the Paducah Tiger Overpack for transportation of those cylinders. The objectives of the study were to determine the maximum amount of water that could be admitted to the interior of such a damaged cylinder, the resulting geometries and chemical compositions from reactions of water with the UF{sub 6} contents of the cylinder, and the end-state water moderated and reflected configurations for input to nuclear criticality safety analyses. The case identified for analysis was the flooding of the inside of a cylinder, submerged horizontally in 3 ft of water. The flooding was driven by an initial pressure drop of 13 psig, through an assumed fracture (1/32 in. wide {times} 1/2 in. deep {times} 18 in. long) in the barrel of the cylinder. During the initial addition of water, transient back pressures occur from the effects of the heats of reaction and solution at the water/UF{sub 6} interface, with some chugging as more water is added to alternately coot the reaction surface and then heat it again as the added water reacts with more UF{sub 6}.

  10. Deep Energy Retrofit Performance Metric Comparison: Eight California Case Studies

    SciTech Connect (OSTI)

    Walker, Iain; Fisher, Jeremy; Less, Brennan

    2014-06-01

    In this paper we will present the results of monitored annual energy use data from eight residential Deep Energy Retrofit (DER) case studies using a variety of performance metrics. For each home, the details of the retrofits were analyzed, diagnostic tests to characterize the home were performed and the homes were monitored for total and individual end-use energy consumption for approximately one year. Annual performance in site and source energy, as well as carbon dioxide equivalent (CO{sub 2}e) emissions were determined on a per house, per person and per square foot basis to examine the sensitivity to these different metrics. All eight DERs showed consistent success in achieving substantial site energy and CO{sub 2}e reductions, but some projects achieved very little, if any source energy reduction. This problem emerged in those homes that switched from natural gas to electricity for heating and hot water, resulting in energy consumption dominated by electricity use. This demonstrates the crucial importance of selecting an appropriate metric to be used in guiding retrofit decisions. Also, due to the dynamic nature of DERs, with changes in occupancy, size, layout, and comfort, several performance metrics might be necessary to understand a project’s success.

  11. EERE Portfolio. Primary Benefits Metrics for FY09

    SciTech Connect (OSTI)

    none,

    2011-11-01

    This collection of data tables shows the benefits metrics related to energy security, environmental impacts, and economic impacts for both the entire EERE portfolio of renewable energy technologies as well as the individual technologies. Data are presented for the years 2015, 2020, 2030, and 2050, for both the NEMS and MARKAL models.

  12. Review of corrosion in 10- and 14-ton mild steel depleted UF{sub 6} storage cylinders

    SciTech Connect (OSTI)

    Lykins, M.L.

    1995-08-01

    A literature review was conducted to determine the type, extent and severity of corrosion found in the 10- and 14-ton mild steel depleted UF{sub 6} storage cylinders. Also discussed in this review is corrosion found in the valves and plugs used in the cylinders. Corrosion of the cylinders is a gradual process which occurs slowly over time. Understanding corrosion of the cylinders is an important concern for long term storage of the UF{sub 6} in the cylinder yards, as well as the final disposition of the depleted UF{sub 6} tails inventory in the future. The following conclusions are made from the literature review: (1) The general external corrosion rate of the cylinders is about 1 to 2 mils per year (1 mil = 0.001{double_prime}). The highest general external corrosion rate was over 5 mpy on the 48G type cylinders. (2) General internal corrosion from the depleted UF{sub 6} is negligible under normal storage conditions. Crevice corrosion can occur at the cylinder/saddle interface from the retention of water in this area. Crevice corrosion can occur at the cylinder/skirt interface on the older skirted cylinders due to the lack of water drainage in this area. Crevice corrosion can occur on cylinders that have been in ground contact. Crevice corrosion and galvanic corrosion can occur where the stainless steel I.D. nameplates are attached to the cylinder. The packing nuts on the bronze one-inch valves used in the cylinders are susceptible to stress corrosion cracking (SCC). Mechanical damage from routine handling can lead to a breach in a cylinder with subsequent accelerated corrosion of the mild steel due to attack from HF and other UF{sub 6} hydrolysis by-products.

  13. Modified Anti-de-Sitter Metric, Light-Front Quantized QCD, and...

    Office of Scientific and Technical Information (OSTI)

    Modified Anti-de-Sitter Metric, Light-Front Quantized QCD, and Conformal Quantum Mechanics Citation Details In-Document Search Title: Modified Anti-de-Sitter Metric, Light-Front...

  14. On the existence of certain axisymmetric interior metrics

    SciTech Connect (OSTI)

    Angulo Santacruz, C.; Batic, D.; Nowakowski, M.

    2010-08-15

    One of the effects of noncommutative coordinate operators is that the delta function connected to the quantum mechanical amplitude between states sharp to the position operator gets smeared by a Gaussian distribution. Although this is not the full account of the effects of noncommutativity, this effect is, in particular, important as it removes the point singularities of Schwarzschild and Reissner-Nordstroem solutions. In this context, it seems to be of some importance to probe also into ringlike singularities which appear in the Kerr case. In particular, starting with an anisotropic energy-momentum tensor and a general axisymmetric ansatz of the metric together with an arbitrary mass distribution (e.g., Gaussian), we derive the full set of Einstein equations that the noncommutative geometry inspired Kerr solution should satisfy. Using these equations we prove two theorems regarding the existence of certain Kerr metrics inspired by noncommutative geometry.

  15. Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasability of a Billion-Ton Annual Supply

    SciTech Connect (OSTI)

    Perlack, R.D.

    2005-12-15

    The U.S. Department of Energy (DOE) and the U.S. Department of Agriculture (USDA) are both strongly committed to expanding the role of biomass as an energy source. In particular, they support biomass fuels and products as a way to reduce the need for oil and gas imports; to support the growth of agriculture, forestry, and rural economies; and to foster major new domestic industries--biorefineries--making a variety of fuels, chemicals, and other products. As part of this effort, the Biomass R&D Technical Advisory Committee, a panel established by the Congress to guide the future direction of federally funded biomass R&D, envisioned a 30 percent replacement of the current U.S. petroleum consumption with biofuels by 2030. Biomass--all plant and plant-derived materials including animal manure, not just starch, sugar, oil crops already used for food and energy--has great potential to provide renewable energy for America's future. Biomass recently surpassed hydropower as the largest domestic source of renewable energy and currently provides over 3 percent of the total energy consumption in the United States. In addition to the many benefits common to renewable energy, biomass is particularly attractive because it is the only current renewable source of liquid transportation fuel. This, of course, makes it invaluable in reducing oil imports--one of our most pressing energy needs. A key question, however, is how large a role could biomass play in responding to the nation's energy demands. Assuming that economic and financial policies and advances in conversion technologies make biomass fuels and products more economically viable, could the biorefinery industry be large enough to have a significant impact on energy supply and oil imports? Any and all contributions are certainly needed, but would the biomass potential be sufficiently large to justify the necessary capital replacements in the fuels and automobile sectors? The purpose of this report is to determine whether the land resources of the United States are capable of producing a sustainable supply of biomass sufficient to displace 30 percent or more of the country's present petroleum consumption--the goal set by the Advisory Committee in their vision for biomass technologies. Accomplishing this goal would require approximately 1 billion dry tons of biomass feedstock per year.

  16. FY 2013 Overall Contract and Project Management Improvement Performance Metrics and Targets

    Broader source: Energy.gov [DOE]

    Overall Contract and Project Management Performance Metrics and Targets for FY 2013, first quarter through fourth quarter.

  17. Guidebook for ARRA Smart Grid Program Metrics and Benefits | Department of

    Energy Savers [EERE]

    Energy Guidebook for ARRA Smart Grid Program Metrics and Benefits Guidebook for ARRA Smart Grid Program Metrics and Benefits The Guidebook for American Recovery and Reinvestment Act (ARRA) Smart Grid Program Metrics and Benefits describes the type of information to be collected from each of the Project Teams and how it will be used by the Department of Energy to communicate overall conclusions to the public. PDF icon Guidebook for ARRA Smart Grid Program Metrics and Benefits More Documents

  18. Office of HC Strategy Budget and Performance Metrics (HC-50) | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Strategy Budget and Performance Metrics (HC-50) Office of HC Strategy Budget and Performance Metrics (HC-50) Mission Statement and Function Statement The Office of Human Capital Strategy, Budget, and Performance Metrics provides strategic direction and advice to its stakeholders through the integration of budget analysis, workforce projections, and performance metrics in support of the goals and missions of the Department of Energy. Functions: Promotes business partnerships with

  19. Optimal recovery of linear operators in non-Euclidean metrics

    SciTech Connect (OSTI)

    Osipenko, K Yu

    2014-10-31

    The paper looks at problems concerning the recovery of operators from noisy information in non-Euclidean metrics. Anumber of general theorems are proved and applied to recovery problems for functions and their derivatives from the noisy Fourier transform. In some cases, afamily of optimal methods is found, from which the methods requiring the least amount of original information are singled out. Bibliography: 25 titles.

  20. Development of Technology Readiness Level (TRL) Metrics and Risk Measures

    SciTech Connect (OSTI)

    Engel, David W.; Dalton, Angela C.; Anderson, K. K.; Sivaramakrishnan, Chandrika; Lansing, Carina

    2012-10-01

    This is an internal project milestone report to document the CCSI Element 7 team's progress on developing Technology Readiness Level (TRL) metrics and risk measures. In this report, we provide a brief overview of the current technology readiness assessment research, document the development of technology readiness levels (TRLs) specific to carbon capture technologies, describe the risk measures and uncertainty quantification approaches used in our research, and conclude by discussing the next steps that the CCSI Task 7 team aims to accomplish.

  1. Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply, April 2005

    SciTech Connect (OSTI)

    2005-04-01

    The purpose of this report is to determine whether the land resources of the United States are capable of producing a sustainable supply of biomass sufficient to displace 30 percent or more of the country’s present petroleum consumption – the goal set by the Biomass R&D Technical Advisory Committee in their vision for biomass technologies. Accomplishing this goal would require approximately 1 billion dry tons of biomass feedstock per year.

  2. A Fluid-Inclusion Investigation Of The Tongonan Geothermal Field...

    Open Energy Info (EERE)

    Fluid-Inclusion Investigation Of The Tongonan Geothermal Field, Philippines Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: A Fluid-Inclusion...

  3. Office of Personnel Management (OPM) Guidance on Diversity and Inclusion |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Office of Personnel Management (OPM) Guidance on Diversity and Inclusion Office of Personnel Management (OPM) Guidance on Diversity and Inclusion The following documents are from the Office of Personnel Management (OMP)'s Office of Diversity and Inclusion, which is responsible for reviewing and evaluating plans, reports, and programs for conformance with various laws, regulations, and directives relating to diversity and inclusion. Governement-Wide Diversity and

  4. Metrics for the National SCADA Test Bed Program

    SciTech Connect (OSTI)

    Craig, Philip A.; Mortensen, J.; Dagle, Jeffery E.

    2008-12-05

    The U.S. Department of Energy Office of Electricity Delivery and Energy Reliability (DOE-OE) National SCADA Test Bed (NSTB) Program is providing valuable inputs into the electric industry by performing topical research and development (R&D) to secure next generation and legacy control systems. In addition, the program conducts vulnerability and risk analysis, develops tools, and performs industry liaison, outreach and awareness activities. These activities will enhance the secure and reliable delivery of energy for the United States. This report will describe metrics that could be utilized to provide feedback to help enhance the effectiveness of the NSTB Program.

  5. User's Guide to the Energy Charting and Metrics Tool (ECAM)

    SciTech Connect (OSTI)

    Taasevigen, Danny J.; Koran, William

    2012-02-28

    The intent of this user guide is to provide a brief description of the functionality of the Energy Charting and Metrics (ECAM) tool, including the expanded building re-tuning functionality developed for Pacific Northwest National laboratory (PNNL). This document describes the tool's general functions and features, and offers detailed instructions for PNNL building re-tuning charts, a feature in ECAM intended to help building owners and operators look at trend data (recommended 15-minute time intervals) in a series of charts (both time series and scatter) to analyze air-handler, zone, and central plant information gathered from a building automation system (BAS).

  6. Assessment of Reusing 14-ton, Thin-Wall, Depleted UF{sub 6} Cylinders as LLW Disposal Containers

    SciTech Connect (OSTI)

    O'Connor, D.G.

    2000-11-30

    Approximately 700,000 MT of DUF{sub 6} is stored, or will be produced under a current agreement with the USEC, at the Paducah site in Kentucky, Portsmouth site in Ohio, and ETTP site in Tennessee. On July 21, 1998, the 105th Congress approved Public Law 105-204 (Ref; 1), which directed that facilities be built at the Kentucky and Ohio sites to convert DUF{sub 6} to a stable form for disposition. On July 6, 1999, the Department of Energy (DOE) issued the ''Final Plan for the Conversion of Depleted Uranium Hexafluoride as Required by Public Law 105-204 (Ref. 2), in which DOE committed to develop a Depleted Uranium Hexafluoride Materials Use Roadmap''. On September 1, 2000, DOE issued the Draft Depleted Uranium Hexafluoride Materials Use Roadmap (Ref. 3) (Roadmap), which provides alternate paths for the long-term storage, beneficial use, and eventual disposition of each product form and material that will result from the DUF{sub 6} conversion activity. One of the paths being considered for DUF{sub 6} cylinders is to reuse the empty cylinders as containers to transport and dispose of LLW, including the converted DU. The Roadmap provides results of the many alternate uses and disposal paths for conversion products and the empty DUF{sub 6} storage cylinders. As a part of the Roadmap, evaluations were conducted of cost savings, technical maturity, barriers to implementation, and other impacts. Results of these evaluations indicate that using the DUF{sub 6} storage cylinders as LLW disposal containers could provide moderate cost savings due to the avoided cost of purchasing LLW packages and the avoided cost of disposing of the cylinders. No significant technical or institutional issues were identified that would make using cylinders as LLW packages less effective than other disposition paths. Over 58,000 cylinders have been used, or will be used, to store DUF{sub 6}. Over 51,000 of those cylinders are 14TTW cylinders with a nominal wall thickness of 5/16-m (0.79 cm). These- 14TTW cylinders, which have a nominal diameter of 48 inches and nominally contain 14 tons (12.7 MT) of DUF{sub 6}, were originally designed and fabricated for temporary storage of DUF{sub 6}. They were fabricated from pressure-vessel-grade steels according to the provisions of the ASME Boiler and Pressure Vessel Code (Ref. 4). Cylinders are stored in open yards at the three sites and, due to historical storage techniques, were subject to corrosion. Roughly 10,000 of the 14TTW cylinders are considered substandard (Ref. 5) due to corrosion and other structural anomalies caused by mishandling. This means that approximately 40,000 14TTW cylinders could be made available as containers for LLW disposal In order to demonstrate the use of 14TTW cylinders as LLW disposal containers, several qualifying tasks need to be performed. Two demonstrations are being considered using 14TTW cylinders--one demonstration using contaminated soil and one demonstration using U{sub 3}O{sub 8}. The objective of this report are to determine how much information is known that could be used to support the demonstrations, and how much additional work will need to be done in order to conduct the demonstrations. Information associated with the following four qualifying tasks are evaluated in this report. (1) Perform a review of structural assessments that have been conducted for 14TTW. (2) Develop a procedure for filling 14TTW cylinders with LLW that have been previously washed. (3) Evaluate the transportation requirements for shipping 14TTW cylinders containing LLW. (4) Evaluate the WAC that will be imposed by the NTS. Two assumptions are made to facilitate this evaluation of using DUF{sub 6} cylinders as LLW disposal containers. (1) Only 14TTW cylinders will be considered for use as LLW containers, and (2) The NTS will be the LLW disposal site.

  7. Semiconducting glasses with flux pinning inclusions

    DOE Patents [OSTI]

    Johnson, William L.; Poon, Siu-Joe; Duwez, Pol E.

    1981-01-01

    A series of amorphous superconducting glassy alloys containing 1% to 10% by volume of flux pinning crystalline inclusions have been found to have potentially useful properties as high field superconducting magnet materials. The alloys are prepared by splat cooling by the piston and anvil technique. The alloys have the composition (TM).sub.90-70 (M).sub.10-30 where TM is a transition metal selected from at least one metal of Groups IVB, VB, VIB, VIIB or VIIIB of the Periodic Table such as Nb, Mo, Ru, Zr, Ta, W or Re and M is at least one metalloid such as B, P, C, N, Si, Ge or Al.

  8. A nuclear criticality safety assessment of the loss of moderation control in 2 1/2 and 10-ton cylinders containing enriched UF{sub 6}

    SciTech Connect (OSTI)

    Newvahner, R.L.; Pryor, W.A.

    1991-12-31

    Moderation control for maintaining nuclear criticality safety in 2 {1/2}-ton, 10-ton, and 14-ton cylinders containing enriched uranium hexafluoride (UF{sub 6}) has been used safely within the nuclear industry for over thirty years, and is dependent on cylinder integrity and containment. This assessment evaluates the loss of moderation control by the breaching of containment and entry of water into the cylinders. The first objective of this study was to estimate the required amounts of water entering these large UF{sub 6} cylinders to react with, and to moderate the uranium compounds sufficiently to cause criticality. Hypothetical accident situations were modeled as a uranyl fluoride (UO{sub 2}F{sub 2}) slab above a UF{sub 6} hemicylinder, and a UO{sub 2}F{sub 2} sphere centered within a UF{sub 6} hemicylinder. These situations were investigated by computational analyses utilizing the KENO V.a Monte Carlo Computer Code. The results were used to estimate both the masses of water required for criticality, and the limiting masses of water that could be considered safe. The second objective of the assessment was to calculate the time available for emergency control actions before a criticality would occur, i.e., a {open_quotes}safetime{close_quotes}, for various sources of water and different size openings in a breached cylinder. In the situations considered, except the case for a fire hose, the safetime appears adequate for emergency control actions. The assessment shows that current practices for handling moderation controlled cylinders of low enriched UF{sub 6}, along with the continuation of established personnel training programs, ensure nuclear criticality safety for routine and emergency operations.

  9. Conceptual Soundness, Metric Development, Benchmarking, and Targeting for PATH Subprogram Evaluation

    SciTech Connect (OSTI)

    Mosey. G.; Doris, E.; Coggeshall, C.; Antes, M.; Ruch, J.; Mortensen, J.

    2009-01-01

    The objective of this study is to evaluate the conceptual soundness of the U.S. Department of Housing and Urban Development (HUD) Partnership for Advancing Technology in Housing (PATH) program's revised goals and establish and apply a framework to identify and recommend metrics that are the most useful for measuring PATH's progress. This report provides an evaluative review of PATH's revised goals, outlines a structured method for identifying and selecting metrics, proposes metrics and benchmarks for a sampling of individual PATH programs, and discusses other metrics that potentially could be developed that may add value to the evaluation process. The framework and individual program metrics can be used for ongoing management improvement efforts and to inform broader program-level metrics for government reporting requirements.

  10. EECBG 10-07C/SEP 10-006B Attachment 1: Process Metrics List |

    Energy Savers [EERE]

    Department of Energy 10-07C/SEP 10-006B Attachment 1: Process Metrics List EECBG 10-07C/SEP 10-006B Attachment 1: Process Metrics List PDF icon eecbg_sep_reporting_guidance_attachment_06242011.pdf More Documents & Publications EECBG SEP Attachment 1 - Process metric list EECBG Program Notice 10-07A DOE Recovery Act Reporting Requirements for the State Energy Program

  11. Microsoft PowerPoint - Snippet 3.2 Schedule Health Metrics 20140713...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... available software. These metrics can be quickly reviewed each month to identify any schedule health risks on your project, whether you are the contractor or the customer. ...

  12. New Selection Metric for Design of Thin-Film Solar Cell Absorber...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Selection Metric for Design of Thin-Film Solar Cell Absorber Materials Research Details * SLME account s for the physics of absorption, emission, and recombination by directly ...

  13. GPRA 2003 quality metrics methodology and results: Office of Industrial Technologies

    SciTech Connect (OSTI)

    None, None

    2002-04-19

    This report describes the results, calculations, and assumptions underlying the GPRA 2003 Quality Metrics results for all Planning Units withing the Office of Industrial Technologies.

  14. Building Cost and Performance Metrics: Data Collection Protocol, Revision 1.0

    SciTech Connect (OSTI)

    Fowler, Kimberly M.; Solana, Amy E.; Spees, Kathleen L.

    2005-09-29

    This technical report describes the process for selecting and applying the building cost and performance metrics for measuring sustainably designed buildings in comparison to traditionally designed buildings.

  15. Variable-metric diffraction crystals for x-ray optics

    SciTech Connect (OSTI)

    Smither, R.K.; Fernandez, P.B. )

    1992-02-01

    A variable-metric (VM) crystal is one in which the spacing between the crystalline planes changes with position in the crystal. This variation can be either parallel to the crystalline planes or perpendicular to the crystalline planes of interest and can be produced by either introducing a thermal gradient in the crystal or by growing a crystal made of two or more elements and changing the relative percentages of the two elements as the crystal is grown. A series of experiments were performed in the laboratory to demonstrate the principle of the variable-metric crystal and its potential use in synchrotron beam lines. One of the most useful applications of the VM crystal is to increase the number of photons per unit bandwidth in a diffracted beam without losing any of the overall intensity. In a normal synchrotron beam line that uses a two-crystal monochromator, the bandwidth of the diffracted photon beam is determined by the vertical opening angle of the beam which is typically 0.10--0.30 mrad or 20--60 arcsec. When the VM crystal approach is applied, the bandwidth of the beam can be made as narrow as the rocking curve of the diffracting crystal, which is typically 0.005--0.050 mrad or 1--10 arcsec. Thus a very large increase of photons per unit bandwidth (or per unit energy) can be achieved through the use of VM crystals. When the VM principle is used with bent crystals, new kinds of x-ray optical elements can be generated that can focus and defocus x-ray beams much like simple lenses where the focal length of the lens can be changed to match its application. Thus both large magnifications and large demagnifications can be achieved as well as parallel beams with narrow bandwidths.

  16. Metrics for Assessment of Smart Grid Data Integrity Attacks

    SciTech Connect (OSTI)

    Annarita Giani; Miles McQueen; Russell Bent; Kameshwar Poolla; Mark Hinrichs

    2012-07-01

    There is an emerging consensus that the nation’s electricity grid is vulnerable to cyber attacks. This vulnerability arises from the increasing reliance on using remote measurements, transmitting them over legacy data networks to system operators who make critical decisions based on available data. Data integrity attacks are a class of cyber attacks that involve a compromise of information that is processed by the grid operator. This information can include meter readings of injected power at remote generators, power flows on transmission lines, and relay states. These data integrity attacks have consequences only when the system operator responds to compromised data by redispatching generation under normal or contingency protocols. These consequences include (a) financial losses from sub-optimal economic dispatch to service loads, (b) robustness/resiliency losses from placing the grid at operating points that are at greater risk from contingencies, and (c) systemic losses resulting from cascading failures induced by poor operational choices. This paper is focused on understanding the connections between grid operational procedures and cyber attacks. We first offer two examples to illustrate how data integrity attacks can cause economic and physical damage by misleading operators into taking inappropriate decisions. We then focus on unobservable data integrity attacks involving power meter data. These are coordinated attacks where the compromised data are consistent with the physics of power flow, and are therefore passed by any bad data detection algorithm. We develop metrics to assess the economic impact of these attacks under re-dispatch decisions using optimal power flow methods. These metrics can be use to prioritize the adoption of appropriate countermeasures including PMU placement, encryption, hardware upgrades, and advance attack detection algorithms.

  17. Inclusive radiative {psi}(2S) decays

    SciTech Connect (OSTI)

    Libby, J.; Martin, L.; Powell, A.; Thomas, C.; Wilkinson, G.; Mendez, H.; Ge, J. Y.; Miller, D. H.; Shipsey, I. P. J.; Xin, B.; Adams, G. S.; Hu, D.; Moziak, B.; Napolitano, J.; Ecklund, K. M.; He, Q.; Insler, J.; Muramatsu, H.; Park, C. S.; Thorndike, E. H.

    2009-10-01

    Using e{sup +}e{sup -} collision data taken with the CLEO-c detector at the Cornell Electron Storage Ring, we have investigated the direct photon spectrum in the decay {psi}(2S){yields}{gamma}gg. We determine the ratio of the inclusive direct photon decay rate to that of the dominant three-gluon decay rate {psi}(2S){yields}ggg (R{sub {gamma}}{identical_to}{gamma}({gamma}gg)/{gamma}(ggg)) to be R{sub {gamma}}(z{sub {gamma}}>0.4)=0.070{+-}0.002{+-}0.019{+-}0.011, with z{sub {gamma}} defined as the scaled photon energy relative to the beam energy. The errors shown are statistical, systematic, and that due to the uncertainty in the input branching fractions used to extract the ratio, respectively.

  18. Inclusive Inelastic Electron Scattering from Nuclei

    SciTech Connect (OSTI)

    Fomin, Nadia

    2007-10-26

    Inclusive electron scattering from nuclei at large x and Q{sup 2} is the result of a reaction mechanism that includes both quasi-elastic scattering from nucleons and deep inelastic scattering from the quark consitituents of the nucleons. Data in this regime can be used to study a wide variety of topics, including the extraction of nuclear momentum distributions, the infiuence of final state interactions and the approach to y-scaling, the strength of nucleon-nucleon correlations, and the approach to x-scaling, to name a few. Selected results from the recent experiment E02-019 at the Thomas Jefferson National Accelerator Facility will be shown and their relevance discussed.

  19. SECTION C

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... tons (2,100 metric tons) of spent nuclear fuel, 11.5 tons (10.5 metric tons) of ... and treat Hanford's tank waste and close the Tank Farms to protect the Columbia River. ...

  20. Diversity and Inclusion Strategic Plan 2012 - 2015 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Strategic Plan 2012 - 2015 Diversity and Inclusion Strategic Plan 2012 - 2015 Our Diversity and Inclusion Strategic Plan is designed to create a culture which values trust and human dignity and provides the opportunity for personal development and self- fulfillment in the attainment of DOE's mission and goals. The 2012- 2015 strategic plan has three essential pillars - mission focus, accountability, and continual learning. It also: Creates a universal definition of diversity and inclusion.

  1. Diversity and Inclusion Town Hall Program Book | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Town Hall Program Book Diversity and Inclusion Town Hall Program Book As part of a larger effort to create a culture that values diversity, we have been conducting focus groups to engage in a dialog and hear feedback on how diversity can be improved. At the Town Hall, DOE employees will hear the results of these discussions. View the program booklet from the Diversity and Inclusion Town Hall below. For more information about the Department's diversity and inclusion programs, visit

  2. Enhanced Inclusion Removal from Steel in the Tundish

    SciTech Connect (OSTI)

    R. C. Bradt; M.A.R. Sharif

    2009-09-25

    The objective of this project was to develop an effective chemical filtering system for significantly reducing the content of inclusion particles in the steel melts exiting the tundish for continuous casting. This project combined a multi-process approach that aimed to make significant progress towards an "inclusion free" steel by incorporating several interdependent concepts to reduce the content of inclusions in the molten steel exiting the tundish for the caster. The goal is to produce "cleaner" steel.

  3. Fluid Inclusion Stratigraphy Interpretation of New Wells in the...

    Open Energy Info (EERE)

    Stratigraphy Interpretation of New Wells in the Coso Geothermal Field Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Fluid Inclusion...

  4. Fluid Inclusion Analysis At Geysers Geothermal Area (1990) |...

    Open Energy Info (EERE)

    Geothermal Area (1990) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Geysers Geothermal Area (1990) Exploration...

  5. Fluid Inclusion Analysis At Coso Geothermal Area (2002) | Open...

    Open Energy Info (EERE)

    2) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Coso Geothermal Area (2002) Exploration Activity Details Location...

  6. Fluid Inclusion Analysis At Chena Geothermal Area (Kolker, 2008...

    Open Energy Info (EERE)

    Chena Geothermal Area (Kolker, 2008) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Chena Geothermal Area (Kolker,...

  7. 36 CFR 63: Determinations of Eligibility for Inclusion in the...

    Open Energy Info (EERE)

    63: Determinations of Eligibility for Inclusion in the National Register of Historic Places Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document-...

  8. Fluid Inclusion Analysis At Salton Sea Geothermal Area (1990...

    Open Energy Info (EERE)

    Salton Sea Geothermal Area (1990) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Salton Sea Geothermal Area (1990)...

  9. Fluid Inclusion Analysis At Yellowstone Region (Sturchio, Et...

    Open Energy Info (EERE)

    Yellowstone Region (Sturchio, Et Al., 1990) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Yellowstone Region...

  10. Fluid Inclusion Analysis At Coso Geothermal Area (1990) | Open...

    Open Energy Info (EERE)

    0) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Coso Geothermal Area (1990) Exploration Activity Details Location...

  11. Fluid Inclusion Analysis At Valles Caldera - Redondo Geothermal...

    Open Energy Info (EERE)

    Redondo Geothermal Area (Sasada, 1988) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Valles Caldera - Redondo...

  12. Fluid Inclusion Analysis At Valles Caldera Geothermal Region...

    Open Energy Info (EERE)

    Geothermal Region (1990) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Valles Caldera Geothermal Region (1990)...

  13. Fluid-inclusion evidence for past temperature fluctuations in...

    Open Energy Info (EERE)

    of the inclusion fluids range from dilute meteoric water to highly modified sea water concentrated by boiling. Comparison of measured drill-hole temperatures with...

  14. Fluid Inclusion Analysis At Raft River Geothermal Area (2011...

    Open Energy Info (EERE)

    Raft River Geothermal Area (2011) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Raft River Geothermal Area (2011)...

  15. Fluid Inclusion Analysis At Lightning Dock Area (Norman & Moore...

    Open Energy Info (EERE)

    Lightning Dock Area (Norman & Moore, 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Lightning Dock Area...

  16. Fluid Inclusion Analysis At Coso Geothermal Area (1996) | Open...

    Open Energy Info (EERE)

    that the interior of the system is still undergoing heating. References Lutz, S. J.; Moore, J. N.; Copp, J. F. (24 January 1996) Integrated mineralogical and fluid inclusion...

  17. Fluid Inclusion Analysis At Geysers Area (Moore, Et Al., 2001...

    Open Energy Info (EERE)

    Area (Moore, Et Al., 2001) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Geysers Area (Moore, Et Al., 2001)...

  18. Fluid Inclusion Analysis At Valles Caldera - Sulphur Springs...

    Open Energy Info (EERE)

    Sulphur Springs Geothermal Area (Sasada & Goff, 1995) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Fluid Inclusion Analysis At Valles Caldera...

  19. Integrated mineralogical and fluid inclusion study of the Coso...

    Open Energy Info (EERE)

    inclusion homogenization temperatures and salinities demonstrate that cool, low salinity ground waters were present when the thermal plume was emplaced. Dilution of the thermal...

  20. Methodologies for Reservoir Characterization Using Fluid Inclusion Gas Chemistry

    Broader source: Energy.gov [DOE]

    Methodologies for Reservoir Characterization Using Fluid Inclusion Gas Chemistry presentation at the April 2013 peer review meeting held in Denver, Colorado.

  1. Enhanced Accident Tolerant LWR Fuels National Metrics Workshop Report

    SciTech Connect (OSTI)

    Lori Braase

    2013-01-01

    The U.S. Department of Energy Office of Nuclear Energy (DOE-NE), in collaboration with the nuclear industry, has been conducting research and development (R&D) activities on advanced Light Water Reactor (LWR) fuels for the last few years. The emphasis for these activities was on improving the fuel performance in terms of increased burnup for waste minimization and increased power density for power upgrades, as well as collaborating with industry on fuel reliability. After the events at the Fukushima Nuclear Power Plant in Japan in March 2011, enhancing the accident tolerance of LWRs became a topic of serious discussion. In the Consolidated Appropriations Act, 2012, Conference Report 112-75, the U.S. Congress directed DOE-NE to: • Give “priority to developing enhanced fuels and cladding for light water reactors to improve safety in the event of accidents in the reactor or spent fuel pools.” • Give “special technical emphasis and funding priority…to activities aimed at the development and near-term qualification of meltdown-resistant, accident-tolerant nuclear fuels that would enhance the safety of present and future generations of light water reactors.” • Report “to the Committee, within 90 days of enactment of this act, on its plan for development of meltdown-resistant fuels leading to reactor testing and utilization by 2020.” Fuels with enhanced accident tolerance are those that, in comparison with the standard UO2-zirconium alloy system currently used by the nuclear industry, can tolerate loss of active cooling in the reactor core for a considerably longer time period (depending on the LWR system and accident scenario) while maintaining or improving the fuel performance during normal operations, and operational transients, as well as design-basis and beyond design-basis events. The overall draft strategy for development and demonstration is comprised of three phases: Feasibility Assessment and Down-selection; Development and Qualification; and Commercialization. The activities performed during the feasibility assessment phase include laboratory scale experiments; fuel performance code updates; and analytical assessment of economic, operational, safety, fuel cycle, and environmental impacts of the new concepts. The development and qualification stage will consist of fuel fabrication and large scale irradiation and safety basis testing, leading to qualification and ultimate NRC licensing of the new fuel. The commercialization phase initiates technology transfer to industry for implementation. Attributes for fuels with enhanced accident tolerance include improved reaction kinetics with steam and slower hydrogen generation rate, while maintaining acceptable cladding thermo-mechanical properties; fuel thermo-mechanical properties; fuel-clad interactions; and fission-product behavior. These attributes provide a qualitative guidance for parameters that must be considered in the development of fuels and cladding with enhanced accident tolerance. However, quantitative metrics must be developed for these attributes. To initiate the quantitative metrics development, a Light Water Reactor Enhanced Accident Tolerant Fuels Metrics Development Workshop was held October 10-11, 2012, in Germantown, Maryland. This document summarizes the structure and outcome of the two-day workshop. Questions regarding the content can be directed to Lori Braase, 208-526-7763, lori.braase@inl.gov.

  2. Description of the Sandia National Laboratories science, technology & engineering metrics process.

    SciTech Connect (OSTI)

    Jordan, Gretchen B.; Watkins, Randall D.; Trucano, Timothy Guy; Burns, Alan Richard; Oelschlaeger, Peter

    2010-04-01

    There has been a concerted effort since 2007 to establish a dashboard of metrics for the Science, Technology, and Engineering (ST&E) work at Sandia National Laboratories. These metrics are to provide a self assessment mechanism for the ST&E Strategic Management Unit (SMU) to complement external expert review and advice and various internal self assessment processes. The data and analysis will help ST&E Managers plan, implement, and track strategies and work in order to support the critical success factors of nurturing core science and enabling laboratory missions. The purpose of this SAND report is to provide a guide for those who want to understand the ST&E SMU metrics process. This report provides an overview of why the ST&E SMU wants a dashboard of metrics, some background on metrics for ST&E programs from existing literature and past Sandia metrics efforts, a summary of work completed to date, specifics on the portfolio of metrics that have been chosen and the implementation process that has been followed, and plans for the coming year to improve the ST&E SMU metrics process.

  3. Impact of Different Economic Performance Metrics on the Perceived Value of Solar Photovoltaics

    SciTech Connect (OSTI)

    Drury, E.; Denholm, P.; Margolis, R.

    2011-10-01

    Photovoltaic (PV) systems are installed by several types of market participants, ranging from residential customers to large-scale project developers and utilities. Each type of market participant frequently uses a different economic performance metric to characterize PV value because they are looking for different types of returns from a PV investment. This report finds that different economic performance metrics frequently show different price thresholds for when a PV investment becomes profitable or attractive. Several project parameters, such as financing terms, can have a significant impact on some metrics [e.g., internal rate of return (IRR), net present value (NPV), and benefit-to-cost (B/C) ratio] while having a minimal impact on other metrics (e.g., simple payback time). As such, the choice of economic performance metric by different customer types can significantly shape each customer's perception of PV investment value and ultimately their adoption decision.

  4. Scale-up of mild gasification to be a process development unit mildgas 24 ton/day PDU design report. Final report, November 1991--July 1996

    SciTech Connect (OSTI)

    1996-03-01

    From November 1991 to April 1996, Kerr McGee Coal Corporation (K-M Coal) led a project to develop the Institute of Gas Technology (IGT) Mild Gasification (MILDGAS) process for near-term commercialization. The specific objectives of the program were to: design, construct, and operate a 24-tons/day adiabatic process development unit (PDU) to obtain process performance data suitable for further design scale-up; obtain large batches of coal-derived co-products for industrial evaluation; prepare a detailed design of a demonstration unit; and develop technical and economic plans for commercialization of the MILDGAS process. The project team for the PDU development program consisted of: K-M Coal, IGT, Bechtel Corporation, Southern Illinois University at Carbondale (SIUC), General Motors (GM), Pellet Technology Corporation (PTC), LTV Steel, Armco Steel, Reilly Industries, and Auto Research.

  5. Sensitivity of Multi-gas Climate Policy to Emission Metrics

    SciTech Connect (OSTI)

    Smith, Steven J.; Karas, Joseph F.; Edmonds, James A.; Eom, Jiyong; Mizrahi, Andrew H.

    2013-04-01

    Multi-gas greenhouse emission targets require that different emissions be combined into an aggregate total. The Global Warming Potential (GWP) index is currently used for this purpose, despite various criticisms of the underlying concept. It is not possible to uniquely define a single metric that perfectly captures the different impacts of emissions of substances with widely disparate atmospheric lifetimes, which leads to a wide range of possible index values. We examine the sensitivity of emissions and climate outcomes to the value of the index used to aggregate methane emissions using a technologically detailed integrated assessment model. We find that the sensitivity to index value is of order 4-14% in terms of methane emissions and 2% in terms of total radiative forcing, using index values between 4 and 70 for methane, with larger regional differences in some cases. The sensitivity to index value is much higher in economic terms, with total 2-gas mitigation cost decreasing 4-5% for a lower index and increasing 10-13% for a larger index, with even larger changes if the emissions reduction targets are small. The sensitivity to index value also depends on the assumed maximum amount of mitigation available in each sector. Evaluation of the maximum mitigation potential for major sources of non-CO2 greenhouse gases would greatly aid analysis

  6. Inclusive radiative J/{psi} decays

    SciTech Connect (OSTI)

    Besson, D.; Pedlar, T. K.; Cronin-Hennessy, D.; Gao, K. Y.; Hietala, J.; Kubota, Y.; Klein, T.; Lang, B. W.; Poling, R.; Scott, A. W.; Zweber, P.; Dobbs, S.; Metreveli, Z.; Seth, K. K.; Tomaradze, A.; Libby, J.; Powell, A.; Wilkinson, G.; Ecklund, K. M.; Love, W.

    2008-08-01

    Using data taken with the CLEO-c detector at the Cornell Electron Storage Ring, we have investigated the direct-photon momentum spectrum in the decay J/{psi}(1S){yields}{gamma}gg, via the ''tagged'' process: e{sup +}e{sup -}{yields}{psi}(2S); {psi}(2S){yields}J/{psi}{pi}{sup +}{pi}{sup -}; J/{psi}{yields}{gamma}+X. Including contributions from two-body radiative decay processes, we find the ratio of the inclusive direct-photon branching fraction to that of the dominant three-gluon branching fraction [R{sub {gamma}}=B(gg{gamma})/B(ggg)] to be R{sub {gamma}}=0.137{+-}0.001{+-}0.016{+-}0.004, where the errors shown are statistical, systematic, and the model-dependent uncertainty related to the extrapolation to zero photon energy. The shape of the scaled photon energy spectrum in J/{psi}{yields}gg{gamma} is observed to be very similar to that of {upsilon}{yields}gg{gamma}. The R{sub {gamma}} value obtained is roughly consistent with that expected by a simple quark-charge scaling [R{sub {gamma}}{approx}(q{sub c}/q{sub b}){sup 2}] of the value determined at the {upsilon}(1S), but somewhat higher than the value expected from the running of the strong coupling constant.

  7. Method for locating metallic nitride inclusions in metallic alloy ingots

    DOE Patents [OSTI]

    White, Jack C.; Traut, Davis E.; Oden, Laurance L.; Schmitt, Roman A.

    1992-01-01

    A method of determining the location and history of metallic nitride and/or oxynitride inclusions in metallic melts. The method includes the steps of labeling metallic nitride and/or oxynitride inclusions by making a coreduced metallic-hafnium sponge from a mixture of hafnium chloride and the chloride of a metal, reducing the mixed chlorides with magnesium, nitriding the hafnium-labeled metallic-hafnium sponge, and seeding the sponge to be melted with hafnium-labeled nitride inclusions. The ingots are neutron activated and the hafnium is located by radiometric means. Hafnium possesses exactly the proper metallurgical and radiochemical properties for this use.

  8. Enclosure - FY 2016 Q1 Metrics Report 2016-02-11.xlsx

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ContractProject Management Performance Metrics FY 2016 Target No. 2 3 4 5 6 7 Comment FY 2016 Forecast Certified Contracting Staff: By the end of FY 2011, 85% of the 1102 ...

  9. Modified Anti-de-Sitter Metric, Light-Front Quantized QCD, and...

    Office of Scientific and Technical Information (OSTI)

    Modified Anti-de-Sitter Metric, Light-Front Quantized QCD, and Conformal Quantum Mechanics Dosch, Hans Gunter; U. Heidelberg, ITP; Brodsky, Stanley J.; SLAC; de Teramond, Guy F.;...

  10. EAC Presentation: Metrics and Benefits Analysis for the ARRA Smart Grid Programs- March 10, 2011

    Broader source: Energy.gov [DOE]

    PowerPoint presentation by Joe Paladino from the Office of Electricity Delivery and Energy Reliability before the Electricity Advisory Committee (EAC) on metrics and benefits analysis for the...

  11. Metrics for Developing an Endorsed Set of Radiographic Threat Surrogates for JINII/CAARS

    SciTech Connect (OSTI)

    Wurtz, R; Walston, S; Dietrich, D; Martz, H

    2009-02-11

    CAARS (Cargo Advanced Automated Radiography System) is developing x-ray dual energy and x-ray backscatter methods to automatically detect materials that are greater than Z=72 (hafnium). This works well for simple geometry materials, where most of the radiographic path is through one material. However, this is usually not the case. Instead, the radiographic path includes many materials of different lengths. Single energy can be used to compute {mu}y{sub l} which is related to areal density (mass per unit area) while dual energy yields more information. This report describes a set of metrics suitable and sufficient for characterizing the appearance of assemblies as detected by x-ray radiographic imaging systems, such as those being tested by Joint Integrated Non-Intrusive Inspection (JINII) or developed under CAARS. These metrics will be simulated both for threat assemblies and surrogate threat assemblies (such as are found in Roney et al. 2007) using geometrical and compositional information of the assemblies. The imaging systems are intended to distinguish assemblies containing high-Z material from those containing low-Z material, regardless of thickness, density, or compounds and mixtures. The systems in question operate on the principle of comparing images obtained by using two different x-ray end-point energies--so-called 'dual energy' imaging systems. At the direction of the DHS JINII sponsor, this report does not cover metrics that implement scattering, in the form of either forward-scattered radiation or high-Z detection systems operating on the principle of backscatter detection. Such methods and effects will be covered in a later report. The metrics described here are to be used to compare assemblies and not x-ray radiography systems. We intend to use these metrics to determine whether two assemblies do or do not look the same. We are tasked to develop a set of assemblies whose appearance using this class of detection systems is indistinguishable from the real threats. To check such an indistinguishability, we must define metrics that are broad enough to cover systems of different source spectra and detector spectral response; in other words, the best metrics should capture physical properties of the assemblies and not the source and detectors employed. In fact, one requirement for the metrics is that, as the detection circumstances change, the similarity or difference of the metrics of two assemblies should be maintained. This report describes the set of two simple 'dual energy' metrics that we have selected. A second report (Wurtz, et al. 2009) goes on to demonstrate several characteristics of the metrics, including how sensitive they are (or are not) to changes in the detection systems, shielding, etc.

  12. Fluid Inclusion Analysis At Coso Geothermal Area (2004-2005)...

    Open Energy Info (EERE)

    and much fine scale detail when the logs are analyzed in detail. References Dilley, L. M.; Norman, D.I.; Berard, B. (1 January 2004) FLUID INCLUSION STRATIGRAPHY: NEW METHOD...

  13. Inclusive Rates and Spectra of the Lambda, Cascade, and Omega...

    Office of Scientific and Technical Information (OSTI)

    ThesisDissertation: Inclusive Rates and Spectra of the Lambda, Cascade, and Omega ... DOE Contract Number: AC02-76SF00515 Resource Type: ThesisDissertation Research Org: ...

  14. Fluid Inclusion Analysis At Coso Geothermal Area (2004) | Open...

    Open Energy Info (EERE)

    DOE-funding Unknown Exploration Basis 1) To determine if analyses of fluid propene and propane species in fluid inclusions can be used to interpret fluid type, history, or process....

  15. Fluid Inclusion Analysis At Coso Geothermal Area (Norman & Moore...

    Open Energy Info (EERE)

    done by our CFS (crushfast-scan) method (Norman 1996) show that chips have a high density of homogeneous fluid inclusions. Analyses were averaged and plotted verses depth, and...

  16. Corrosion of aluminum clad spent nuclear fuel in the 70 ton cask during transfer from L area to H-canyon

    SciTech Connect (OSTI)

    Mickalonis, J. I.

    2015-08-01

    Aluminum-clad spent nuclear fuel will be transported for processing in the 70-ton nuclear fuel element cask from L Basin to H-canyon. During transport these fuels would be expected to experience high temperature aqueous corrosion from the residual L Basin water that will be present in the cask. Cladding corrosion losses during transport were calculated for material test reactor (MTR) and high flux isotope reactors (HFIR) fuels using literature and site information on aqueous corrosion at a range of time/temperature conditions. Calculations of the cladding corrosion loss were based on Arrhenius relationships developed for aluminum alloys typical of cladding material with the primary assumption that an adherent passive film does not form to retard the initial corrosion rate. For MTR fuels a cladding thickness loss of 33% was found after 1 year in the cask with a maximum temperature of 263 °C. HFIR fuels showed a thickness loss of only 6% after 1 year at a maximum temperature of 180 °C. These losses are not expected to impact the overall confinement function of the aluminum cladding.

  17. CORROSION OF ALUMINUM CLAD SPENT NUCLEAR FUEL IN THE 70 TON CASK DURING TRANSFER FROM L AREA TO H-CANYON

    SciTech Connect (OSTI)

    Mickalonis, J.

    2014-06-01

    Aluminum-clad spent nuclear fuel will be transported for processing in the 70-ton nuclear fuel element cask from L Basin to H-canyon. During transport these fuels would be expected to experience high temperature aqueous corrosion from the residual L Basin water that will be present in the cask. Cladding corrosion losses during transport were calculated for material test reactor (MTR) and high flux isotope reactors (HFIR) fuels using literature and site information on aqueous corrosion at a range of time/temperature conditions. Calculations of the cladding corrosion loss were based on Arrhenius relationships developed for aluminum alloys typical of cladding material with the primary assumption that an adherent passive film does not form to retard the initial corrosion rate. For MTR fuels a cladding thickness loss of 33 % was found after 1 year in the cask with a maximum temperature of 260 {degrees}C. HFIR fuels showed a thickness loss of only 6% after 1 year at a maximum temperature of 180 {degrees}C. These losses are not expected to impact the overall confinement function of the aluminum cladding.

  18. Corrosion of aluminum clad spent nuclear fuel in the 70 ton cask during transfer from L area to H-canyon

    SciTech Connect (OSTI)

    Mickalonis, J. I.

    2015-08-31

    Aluminum-clad spent nuclear fuel will be transported for processing in the 70-ton nuclear fuel element cask from L Basin to H-canyon. During transport these fuels would be expected to experience high temperature aqueous corrosion from the residual L Basin water that will be present in the cask. Cladding corrosion losses during transport were calculated for material test reactor (MTR) and high flux isotope reactors (HFIR) fuels using literature and site information on aqueous corrosion at a range of time/temperature conditions. Calculations of the cladding corrosion loss were based on Arrhenius relationships developed for aluminum alloys typical of cladding material with the primary assumption that an adherent passive film does not form to retard the initial corrosion rate. For MTR fuels a cladding thickness loss of 33 % was found after 1 year in the cask with a maximum temperature of 263 °C. HFIR fuels showed a thickness loss of only 6% after 1 year at a maximum temperature of 180 °C. These losses are not expected to impact the overall confinement function of the aluminum cladding.

  19. Bibliographic survey of medium energy inclusive reaction data

    SciTech Connect (OSTI)

    Arthur, E.D.; Madland, D.G.; McClellan, D.M.

    1986-04-01

    A bibliographic survey of inclusive reaction data (experimental and theoretical) for several projectile types having energies between 50 and 1000 MeV has been completed. Approximately one thousand references selected from this survey describe the current state of knowledge for particle-induced inclusive reaction data. The search covered data for the following projectiles: p, d, t, /sup 3/He, /sup 4/He, and lithium ions.

  20. Mary Ann Fresco receives OPM award for creating, fostering inclusive

    National Nuclear Security Administration (NNSA)

    diversity | National Nuclear Security Administration Mary Ann Fresco receives OPM award for creating, fostering inclusive diversity Thursday, February 5, 2015 - 3:16pm Mary Ann Fresco, Senior Advisor to NNSA's Management and Business Office (NA-MB), was recently recognized by the Office of Personnel Management (OPM) for her contributions to creating and fostering inclusive diversity in the federal government. She recently participated in an interagency detail to OPM where she led change and

  1. Implementing the Data Center Energy Productivity Metric in a High Performance Computing Data Center

    SciTech Connect (OSTI)

    Sego, Landon H.; Marquez, Andres; Rawson, Andrew; Cader, Tahir; Fox, Kevin M.; Gustafson, William I.; Mundy, Christopher J.

    2013-06-30

    As data centers proliferate in size and number, the improvement of their energy efficiency and productivity has become an economic and environmental imperative. Making these improvements requires metrics that are robust, interpretable, and practical. We discuss the properties of a number of the proposed metrics of energy efficiency and productivity. In particular, we focus on the Data Center Energy Productivity (DCeP) metric, which is the ratio of useful work produced by the data center to the energy consumed performing that work. We describe our approach for using DCeP as the principal outcome of a designed experiment using a highly instrumented, high-performance computing data center. We found that DCeP was successful in clearly distinguishing different operational states in the data center, thereby validating its utility as a metric for identifying configurations of hardware and software that would improve energy productivity. We also discuss some of the challenges and benefits associated with implementing the DCeP metric, and we examine the efficacy of the metric in making comparisons within a data center and between data centers.

  2. Inclusive decays of {ital B} mesons to charmonium

    SciTech Connect (OSTI)

    Balest, R.; Cho, K.; Ford, W.T.; Johnson, D.R.; Lingel, K.; Lohner, M.; Rankin, P.; Smith, J.G.; Alexander, J.P.; Bebek, C.; Berkelman, K.; Bloom, K.; Browder, T.E.; Cassel, D.G.; Cho, H.A.; Coffman, D.M.; Crowcroft, D.S.; Drell, P.S.; Dumas, D.J.; Ehrlich, R.; Gaidarev, P.; Garcia-Sciveres, M.; Geiser, B.; Gittelman, B.; Gray, S.W.; Hartill, D.L.; Heltsley, B.K.; Henderson, S.; Jones, C.D.; Jones, S.L.; Kandaswamy, J.; Katayama, N.; Kim, P.C.; Kreinick, D.L.; Ludwig, G.S.; Masui, J.; Mevissen, J.; Mistry, N.B.; Ng, C.R.; Nordberg, E.; Patterson, J.R.; Peterson, D.; Riley, D.; Salman, S.; Sapper, M.; Wuerthwein, F.; Avery, P.; Freyberger, A.; Rodriguez, J.; Yang, S.; Yelton, J.; Cinabro, D.; Liu, T.; Saulnier, M.; Wilson, R.; Yamamoto, H.; Bergfeld, T.; Eisenstein, B.I.; Gollin, G.; Ong, B.; Palmer, M.; Selen, M.; Thaler, J.J.; Edwards, K.W.; Ogg, M.; Bellerive, A.; Britton, D.I.; Hyatt, E.R.F.; MacFarlane, D.B.; Patel, P.M.; Spaan, B.; Sadoff, A.J.; Ammar, R.; Baringer, P.; Bean, A.; Besson, D.; Coppage, D.; Copty, N.; Davis, R.; Hancock, N.; Kelly, M.; Kotov, S.; Kravchenko, I.; Kwak, N.; Lam, H.; Kubota, Y.; Lattery, M.; Momayezi, M.; Nelson, J.K.; Patton, S.; Poling, R.; Savinov, V.; Schrenk, S.; Wang, R.; Alam, M.S.; Kim, I.J.; Ling, Z.; Mahmood, A.H.; O`Neill, J.J.; Severini, H.; Sun, C.R.; Wappler, F.; Crawford, G.; Daubenmier, C.M.; Fulton, R.; Fujino, D.; Gan, K.K.; Honscheid, K.; Kagan, H.; Kass, R.; Lee, J.; Sung, M.; White, C.; Wolf, A.; Zoeller, M.M.; Butler, F.; Fu, X.; Nemati, B.; Ross, W.R.; Skubic, P.; Wood, M.; Bishai, M.; Fast, J.; Gerndt, E.; Hinson, J.W.; McIlwain, R.L.; Miao, T.; Miller, D.H.; Modesitt, M.; Payne, D.; Shibata, E.I.; Shipsey, I.P.J.; Wang, P.N.; Battle, M.; Ernst, J.; Gibbons, L.; Kwon, Y.; Roberts, S.; Thorndike, E.H.; Wang, C.H.; Dominick, J.; Lambrecht, M.; Sanghera, S.; Shelkov, V.; Skwarnicki, T.; Stroynowski, R.; Volobouev, I.; Wei, G.; Artuso, M.; Gao, M.; Goldberg, M.; He, D.; Horwitz, N.; Moneti, G.C.; (CLEO Collabor..

    1995-09-01

    We have used the CLEO-II detector at the Cornell Electron Storage Ringe (CESR) to study the inclusive production of charmonium mesons in a sample of 2.15 million {ital B{bar B}} events. We find inclusive branching fractions of (1.12{plus_minus}0.04{plus_minus}0.06)% for {ital B}{r_arrow}{ital J}/{psi}{ital X}, (0.34{plus_minus}0.04{plus_minus}0.03)% for {ital B}{r_arrow}{psi}{prime}{ital X}, and (0.40{plus_minus}0.06{plus_minus}0.04)% for {ital B}{r_arrow}{chi}{sub {ital c}1}{ital X}. We also find some evidence for the inclusive production of {chi}{sub {ital c}2}, and set an upper limit for the branching fraction of the inclusive decay {ital B}{r_arrow}{eta}{sub {ital c}}{ital X} of 0.9% at 90% confidence level. Momentum spectra for inclusive {ital J}/{psi}, {psi}{prime}, and {chi}{sub {ital c}1} production are presented. These measurements are compared to theoretical calculations.

  3. Inclusion in the Workplace - Text Version | Careers | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Inclusion in the Workplace - Text Version This is the text version for the Inclusion in the Workplace video. Manajit Sengupta: I work at NREL because of primarily the challenges, the excitement of the work, and the people I work with. Suzy Belmont: When people feel safe and they feel accepted, they're able to bring the best parts of themselves forward, and they're able to bring exciting new ideas forward because they feel like they can fail, they feel like they can try out new things. Bobi

  4. Diversity and Inclusion Events Calendar | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Diversity and Inclusion Events Calendar Diversity and Inclusion Events Calendar Training, networking, and career-building conferences like the ones below are valuable ways to engage in diversity issues. Learn about upcoming events on the calendar below, and contact us at diversity@hq.doe.gov to let us know about other upcoming events. To learn more about the Department's diversity initiatives, visit this page. May 2016 < prev next > Sun Mon Tue Wed Thu Fri Sat 1 2 3 4 5 6 7 8 9 10 11 12 13

  5. Methodologies for Reservoir Characterization Using Fluid Inclusion Gas Chemistry

    SciTech Connect (OSTI)

    Dilley, Lorie M.

    2015-04-13

    The purpose of this project was to: 1) evaluate the relationship between geothermal fluid processes and the compositions of the fluid inclusion gases trapped in the reservoir rocks; and 2) develop methodologies for interpreting fluid inclusion gas data in terms of the chemical, thermal and hydrological properties of geothermal reservoirs. Phase 1 of this project was designed to conduct the following: 1) model the effects of boiling, condensation, conductive cooling and mixing on selected gaseous species; using fluid compositions obtained from geothermal wells, 2) evaluate, using quantitative analyses provided by New Mexico Tech (NMT), how these processes are recorded by fluid inclusions trapped in individual crystals; and 3) determine if the results obtained on individual crystals can be applied to the bulk fluid inclusion analyses determined by Fluid Inclusion Technology (FIT). Our initial studies however, suggested that numerical modeling of the data would be premature. We observed that the gas compositions, determined on bulk and individual samples were not the same as those discharged by the geothermal wells. Gases discharged from geothermal wells are CO2-rich and contain low concentrations of light gases (i.e. H2, He, N, Ar, CH4). In contrast many of our samples displayed enrichments in these light gases. Efforts were initiated to evaluate the reasons for the observed gas distributions. As a first step, we examined the potential importance of different reservoir processes using a variety of commonly employed gas ratios (e.g. Giggenbach plots). The second technical target was the development of interpretational methodologies. We have develop methodologies for the interpretation of fluid inclusion gas data, based on the results of Phase 1, geologic interpretation of fluid inclusion data, and integration of the data. These methodologies can be used in conjunction with the relevant geological and hydrological information on the system to create fluid models for the system. The hope is that the methodologies developed will allow bulk fluid inclusion gas analysis to be a useful tool for estimating relative temperatures, identifying the sources and origins of the geothermal fluids, and developing conceptual models that can be used to help target areas of enhanced permeability.

  6. Microsoft Word - 2014-1-1 RCA Qtr 1 Metrics Attachment_R1

    Energy Savers [EERE]

    4 First Quarter Overall Root Cause Analysis (RCA)/Corrective Action Plan (CAP) Performance Metrics 1 Contract/Project Management Performance Metric FY 2014 Target FY 2014 Projected FY 2014 Pre- & Post-CAP* Projected Comment Capital Asset Project Success: Complete 90% of capital asset projects at original scope and within 110% of CD-2 TPC. 90% 75% Construction 81% Cleanup 67% 67% Pre-CAP 75% Post-CAP Based on 3-year rolling period (FY12 to FY14) TPC is Total Project Cost. Contract/Project

  7. Microsoft Word - 2014-5-27 RCA Qtr 2 Metrics Attachment_R1

    Energy Savers [EERE]

    Second Quarter Overall Root Cause Analysis (RCA)/Corrective Action Plan (CAP) Performance Metrics 1 Contract/Project Management Performance Metric FY 2014 Target FY 2014 Projected FY 2014 Pre- & Post-CAP* Projected Comment Capital Asset Project Success: Complete 90% of capital asset projects at original scope and within 110% of CD-2 TPC. 90% 75% Construction 81% Cleanup 67% 67% Pre-CAP 75% Post-CAP Based on 3-year rolling period (FY12 to FY14) TPC is Total Project Cost. Contract/Project

  8. FY 2014 Q3 RCA CAP Performance Metrics Report 2014-09-05.xlsx

    Energy Savers [EERE]

    Third Quarter Overall Root Cause Analysis (RCA)/Corrective Action Plan (CAP) Performance Metrics No. Contract/Project Management Performance Metrics FY 2014 Target FY 2014 Pre- & Post- CAP* Projected Comment 1 Capital Asset Project Success: Complete 90% of capital asset projects at original scope and within 110% of CD-2 TPC. 90% 67% Pre-CAP 75% Post-CAP Based on 3-year rolling period (FY12 to FY14). TPC is Total Project Cost. No. FY 2014 Target FY 2014 3rd Qtr Actual 2 95% 92% 3 95% 90% 4

  9. FY 2014 Q4 Metrics Report 2014-11-06.xlsx

    Energy Savers [EERE]

    Fourth Quarter Overall Root Cause Analysis (RCA)/Corrective Action Plan (CAP) Performance Metrics No. Contract/Project Management Performance Metrics FY 2014 Target FY 2014 Pre- & Post- CAP* Actual Comment 1 Capital Asset Project Success: Complete 90% of capital asset projects at original scope and within 110% of CD-2 TPC. 90% 67% Pre-CAP 76% Post-CAP Based on 3-year rolling period (FY12 to FY14). TPC is Total Project Cost. No. FY 2014 Target FY 2014 4th Qtr Actual 2 95% 89% 3 95% 94% 4 90%

  10. Enclosure - FY 2015 Q4 Metrics Report 2015-11-02.xlsx

    Energy Savers [EERE]

    Fourth Quarter Overall Root Cause Analysis (RCA)/Corrective Action Plan (CAP) Performance Metrics No. Contract/Project Management Performance Metrics FY 2015 Target Comment No. 2 3 4 5 6 7 1 Capital Asset Project Success: Complete 90% of capital asset projects at original scope and within 110% of CD-2 TPC. 90% FY13-FY15: 40 completions through 4th Qtr. CD-4: Critical Decision-4, Approve Start of Operations/Project Completion. FY13-FY15: 4 completions through 4th Qtr. Based on 3-year rolling

  11. Furnace Standard Analysis Discussion Document

    Office of Environmental Management (EM)

    heating systems could have on overall energy usage, cost, and carbon emissions outcomes. ... Tons 4.5 Metric Tons 3.5 Metric Tons Annual Cost 1,119 1,029 1,806 714 544 ...

  12. Multidimensional metrics for estimating phage abundance, distribution, gene density, and sequence coverage in metagenomes

    SciTech Connect (OSTI)

    Aziz, Ramy K.; Dwivedi, Bhakti; Akhter, Sajia; Breitbart, Mya; Edwards, Robert A.

    2015-05-08

    Phages are the most abundant biological entities on Earth and play major ecological roles, yet the current sequenced phage genomes do not adequately represent their diversity, and little is known about the abundance and distribution of these sequenced genomes in nature. Although the study of phage ecology has benefited tremendously from the emergence of metagenomic sequencing, a systematic survey of phage genes and genomes in various ecosystems is still lacking, and fundamental questions about phage biology, lifestyle, and ecology remain unanswered. To address these questions and improve comparative analysis of phages in different metagenomes, we screened a core set of publicly available metagenomic samples for sequences related to completely sequenced phages using the web tool, Phage Eco-Locator. We then adopted and deployed an array of mathematical and statistical metrics for a multidimensional estimation of the abundance and distribution of phage genes and genomes in various ecosystems. Experiments using those metrics individually showed their usefulness in emphasizing the pervasive, yet uneven, distribution of known phage sequences in environmental metagenomes. Using these metrics in combination allowed us to resolve phage genomes into clusters that correlated with their genotypes and taxonomic classes as well as their ecological properties. By adding this set of metrics to current metaviromic analysis pipelines, where they can provide insight regarding phage mosaicism, habitat specificity, and evolution.

  13. Multidimensional metrics for estimating phage abundance, distribution, gene density, and sequence coverage in metagenomes

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aziz, Ramy K.; Dwivedi, Bhakti; Akhter, Sajia; Breitbart, Mya; Edwards, Robert A.

    2015-05-08

    Phages are the most abundant biological entities on Earth and play major ecological roles, yet the current sequenced phage genomes do not adequately represent their diversity, and little is known about the abundance and distribution of these sequenced genomes in nature. Although the study of phage ecology has benefited tremendously from the emergence of metagenomic sequencing, a systematic survey of phage genes and genomes in various ecosystems is still lacking, and fundamental questions about phage biology, lifestyle, and ecology remain unanswered. To address these questions and improve comparative analysis of phages in different metagenomes, we screened a core set ofmore » publicly available metagenomic samples for sequences related to completely sequenced phages using the web tool, Phage Eco-Locator. We then adopted and deployed an array of mathematical and statistical metrics for a multidimensional estimation of the abundance and distribution of phage genes and genomes in various ecosystems. Experiments using those metrics individually showed their usefulness in emphasizing the pervasive, yet uneven, distribution of known phage sequences in environmental metagenomes. Using these metrics in combination allowed us to resolve phage genomes into clusters that correlated with their genotypes and taxonomic classes as well as their ecological properties. By adding this set of metrics to current metaviromic analysis pipelines, where they can provide insight regarding phage mosaicism, habitat specificity, and evolution.« less

  14. Metrics of closed world of Friedmann, agitated by electric charge (towards a theory electromagnetic Friedmanns)

    SciTech Connect (OSTI)

    Markov, M.A.; Frolov, V.P.

    1986-06-10

    The generalization is considered of the well-known Tolman problem to the case of electrically charged dust-like matter of the central symmetrical system. The first integrals of the correspondent system of the Einstein-Maxwell equations are found. The problem is specificated in such a way that with the full charge of the system going to zero, the metrics of the closed Friedman world arises. Such a system is considered at the initial moment, that of maximal enlargement. With any nonvanishing but no-matter-how-small value of the electric charge, the metrics is unclosed. The metrics of the almost-Friedmanian part of the world allows the continuation through the narrow manhole (at the small charge) as the Nordstroem Reissner metrics with the parameters m/sub O/ sq rt (chi) = e/sub o/. The expression for the electric potential in the manhole phi/sub h/ = c-squared/sq rt chi does not depend upon the value of the electric charge. The radius of the manhole r/sub h/ = e/sub O/ sq. rt (chi)/ c-squared increases with the increase of the charge. The state of the manhole as given by the classical description appears as essentially unstable from the quantum-physics viewpoint. The production of various pairs in the enormous electric fields of the manhole gives rise to the polarisation of the latter up to effective charge Z < 137e irrespective of the initial (no matter how great) charge of the system.

  15. Development of new VOC exposure metrics and their relationship to ''Sick Building Syndrome'' symptoms

    SciTech Connect (OSTI)

    Ten Brinke, JoAnn

    1995-08-01

    Volatile organic compounds (VOCs) are suspected to contribute significantly to ''Sick Building Syndrome'' (SBS), a complex of subchronic symptoms that occurs during and in general decreases away from occupancy of the building in question. A new approach takes into account individual VOC potencies, as well as the highly correlated nature of the complex VOC mixtures found indoors. The new VOC metrics are statistically significant predictors of symptom outcomes from the California Healthy Buildings Study data. Multivariate logistic regression analyses were used to test the hypothesis that a summary measure of the VOC mixture, other risk factors, and covariates for each worker will lead to better prediction of symptom outcome. VOC metrics based on animal irritancy measures and principal component analysis had the most influence in the prediction of eye, dermal, and nasal symptoms. After adjustment, a water-based paints and solvents source was found to be associated with dermal and eye irritation. The more typical VOC exposure metrics used in prior analyses were not useful in symptom prediction in the adjusted model (total VOC (TVOC), or sum of individually identified VOCs ({Sigma}VOC{sub i})). Also not useful were three other VOC metrics that took into account potency, but did not adjust for the highly correlated nature of the data set, or the presence of VOCs that were not measured. High TVOC values (2--7 mg m{sup {minus}3}) due to the presence of liquid-process photocopiers observed in several study spaces significantly influenced symptoms. Analyses without the high TVOC values reduced, but did not eliminate the ability of the VOC exposure metric based on irritancy and principal component analysis to explain symptom outcome.

  16. Quantitative metrics for assessment of chemical image quality and spatial resolution

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kertesz, Vilmos; Cahill, John F.; Van Berkel, Gary J.

    2016-02-28

    Rationale: Currently objective/quantitative descriptions of the quality and spatial resolution of mass spectrometry derived chemical images are not standardized. Development of these standardized metrics is required to objectively describe chemical imaging capabilities of existing and/or new mass spectrometry imaging technologies. Such metrics would allow unbiased judgment of intra-laboratory advancement and/or inter-laboratory comparison for these technologies if used together with standardized surfaces. Methods: We developed two image metrics, viz., chemical image contrast (ChemIC) based on signal-to-noise related statistical measures on chemical image pixels and corrected resolving power factor (cRPF) constructed from statistical analysis of mass-to-charge chronograms across features of interest inmore » an image. These metrics, quantifying chemical image quality and spatial resolution, respectively, were used to evaluate chemical images of a model photoresist patterned surface collected using a laser ablation/liquid vortex capture mass spectrometry imaging system under different instrument operational parameters. Results: The calculated ChemIC and cRPF metrics determined in an unbiased fashion the relative ranking of chemical image quality obtained with the laser ablation/liquid vortex capture mass spectrometry imaging system. These rankings were used to show that both chemical image contrast and spatial resolution deteriorated with increasing surface scan speed, increased lane spacing and decreasing size of surface features. Conclusions: ChemIC and cRPF, respectively, were developed and successfully applied for the objective description of chemical image quality and spatial resolution of chemical images collected from model surfaces using a laser ablation/liquid vortex capture mass spectrometry imaging system.« less

  17. Microsoft Word - DOE 2012-2015 Diversityand inclusion Strategic Plan

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0 1 2 - 2 0 1 5 D e p a r t me n t o f E n e r g y D i v e r s i t y & I n c l u s i o n S t r a t e g i c P l a n Department of Energy's Diversity and Inclusion Strategic Plan: 2012 -2015 i Message from the March 23, 2012 Secretary of Energy The Department of Energy (DOE) is pleased to provide its 2012-2015 Diversity and Inclusion Strategic Plan. Achieving the Department of Energy's mission and goals will involve creating a culture which values the contributions of all DOE employees and

  18. Elimination of platinum inclusions in phosphate laser glasses

    SciTech Connect (OSTI)

    Campbell, J.H.; Wallerstein, E.P. ); Hayden, J.S.; Sapak, D.L.; Warrington, D.E.; Marker, A.J. III ); Toratani, H.; Meissner, H.; Nakajima, S.; Izumitani, T. )

    1989-05-26

    Results from small-scale glass melting experiments aimed at reducing the density of platinum particles in phosphate laser glasses are discussed. The platinum particles originate from the crucibles used to melt the laser glass and can cause optical damage in glasses used in high-peak-power lasers; this problem was particularly acute in the LLNL 120 kJ, 100 TW Nova laser. The melting experiments examine the effects of (i) N{sub 2}, O{sub 2}, and Cl{sub 2} gas atmospheres; (ii) temperature and temperature gradients; (iii) processing time; and (iv) platinum alloys on the formation and dissolution of platinum inclusions in LHG-8 and LG-750 phosphate laser glasses. Results show that most platinum inclusions originate early in the melt cycle, with thermal gradients within the melter being one of the major causes. By using oxidizing gas conditions (O{sub 2}, Cl{sub 2}, or O{sub 2} + Cl{sub 2}), the platinum inclusions can be dissolved into the glass during the course of the melt cycle. The dissolution rate of platinum under oxidizing conditions has been measured, and a model is used to quantify the description of the dissolution process. The effect of ionic platinum on the transmission spectra of the laser glasses produced under various oxidizing conditions has also been measured. Results from the above laboratory-scale melting experiments have been incorporated into proprietary laser-glass melting processes. The laser glasses prepared under these conditions have an average of less than 0.1 platinum inclusions/liter, which represents a 1000-fold reduction over the previously available phosphate laser glasses. 52 refs., 56 figs., 15 tabs.

  19. Inclusive jet cross-section measurement at CDF

    SciTech Connect (OSTI)

    Norniella, Olga; /Barcelona, IFAE

    2007-05-01

    The CDF Collaboration has measured the inclusive jet cross section using 1992-93 collider data at 1.8 TeV. The CDF measurement is in very good agreement with NLO QCD predictions for transverse energies (E{sub T}) below 200 GeV. However, it is systematically higher than NLO QCD predictions for E{sub T} above 200 GeV.

  20. Black Warrior: Sub-soil gas and fluid inclusion exploration and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Black Warrior: Sub-soil gas and fluid inclusion exploration and slim well drilling Black Warrior: Sub-soil gas and fluid inclusion exploration and slim well drilling DOE Geothermal ...

  1. Momentum space dipole amplitude for DIS and inclusive hadron production

    SciTech Connect (OSTI)

    Basso, E. A.; Gay Ducati, M. B.; De Oliveira, E. G.

    2013-03-25

    We show how the AGBS model, originally developed for deep inelastic scattering applied to HERA data on the proton structure function, can also describe the RHIC data on single inclusive hadron yield for d+Au and p+p collisions through a new simultaneous fit. The single inclusive hadron production is modeled through the color glass condensate, which uses the quark(and gluon) condensate amplitudes in momentum space. The AGBS model is also a momentum space model based on the asymptotic solutions of the BK equation, although a different definition of the Fourier transform is used. This description entirely in transverse momentum of both processes arises for the first time. The small difference between the simultaneous fit and the one for HERA data alone suggests that the AGBS model describes very well both kind of processes and thus emerges as a good tool to investigate the inclusive hadron production data. We use this model for predictions at LHC energies, which agree quite well with available experimental data.

  2. Advanced Nuclear Technology: Advanced Light Water Reactors Utility Requirements Document Small Modular Reactors Inclusion Summary

    Broader source: Energy.gov [DOE]

    Advanced Nuclear Technology: Advanced Light Water Reactors Utility Requirements Document Small Modular Reactors Inclusion Summary November 2014

  3. Corrosion of Metal Inclusions In Bulk Vitrification Waste Packages

    SciTech Connect (OSTI)

    Bacon, Diana H.; Pierce, Eric M.; Wellman, Dawn M.; Strachan, Denis M.; Josephson, Gary B.

    2006-07-31

    The primary purpose of the work reported here is to analyze the potential effect of the release of technetium (Tc) from metal inclusions in bulk vitrification waste packages once they are placed in the Integrated Disposal Facility (IDF). As part of the strategy for immobilizing waste from the underground tanks at Hanford, selected wastes will be immobilized using bulk vitrification. During analyses of the glass produced in engineering-scale tests, metal inclusions were found in the glass product. This report contains the results from experiments designed to quantify the corrosion rates of metal inclusions found in the glass product from AMEC Test ES-32B and simulations designed to compare the rate of Tc release from the metal inclusions to the release of Tc from glass produced with the bulk vitrification process. In the simulations, the Tc in the metal inclusions was assumed to be released congruently during metal corrosion as soluble TcO4-. The experimental results and modeling calculations show that the metal corrosion rate will, under all conceivable conditions at the IDF, be dominated by the presence of the passivating layer and corrosion products on the metal particles. As a result, the release of Tc from the metal particles at the surfaces of fractures in the glass releases at a rate similar to the Tc present as a soluble salt. The release of the remaining Tc in the metal is controlled by the dissolution of the glass matrix. To summarize, the release of 99Tc from the BV glass within precipitated Fe is directly proportional to the diameter of the Fe particles and to the amount of precipitated Fe. However, the main contribution to the Tc release from the iron particles is over the same time period as the release of the soluble Tc salt. For the base case used in this study (0.48 mass% of 0.5 mm diameter metal particles homogeneously distributed in the BV glass), the release of 99Tc from the metal is approximately the same as the release from 0.3 mass% soluble Tc salt in the castable refractory block and it is released over the same time period as the salt. Therefore, to limit the impact of precipitated Fe on the release of 99Tc, both the amount of precipitated Fe in the BV glass and the diameter of these particles should be minimized.

  4. The International Safeguards Technology Base: How is the Patient Doing? An Exploration of Effective Metrics

    SciTech Connect (OSTI)

    Schanfein, Mark J; Gouveia, Fernando S

    2010-07-01

    The term “Technology Base” is commonly used but what does it mean? Is there a common understanding of the components that comprise a technology base? Does a formal process exist to assess the health of a given technology base? These are important questions the relevance of which is even more pressing given the USDOE/NNSA initiatives to strengthen the safeguards technology base through investments in research & development and human capital development. Accordingly, the authors will establish a high-level framework to define and understand what comprises a technology base. Potential goal-driven metrics to assess the health of a technology base will also be explored, such as linear demographics and resource availability, in the hope that they can be used to better understand and improve the health of the U.S. safeguards technology base. Finally, through the identification of such metrics, the authors will offer suggestions and highlight choices for addressing potential shortfalls.

  5. Microsoft Word - McIntyre-Metrics Report SAND draft9-14.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2070P Unlimited Release September 2007 Security Metrics for Process Control Systems Annie McIntyre, Blair Becker, Ron Halbgewachs Prepared by Sandia National Laboratories Albuquerque, New Mexico 87185 and Livermore, California 94550 Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000. Approved for public release; further dissemination

  6. Microsoft Word - McIntyre-Metrics Report SAND draft9-14.doc

    Energy Savers [EERE]

    2070P Unlimited Release September 2007 Security Metrics for Process Control Systems Annie McIntyre, Blair Becker, Ron Halbgewachs Prepared by Sandia National Laboratories Albuquerque, New Mexico 87185 and Livermore, California 94550 Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000. Approved for public release; further dissemination

  7. Resilience Metrics

    Broader source: Energy.gov (indexed) [DOE]

    ... resilience picture - Developed first dependency dashboards - Used IAC developed ... discussions with stakeholders - Dependency curves - Report that synthesizes ...

  8. Metric Presentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Funded by the U.S. Department of Energy, Office of Electricity Delivery and Energy Reliability 2 Office of Electricity Delivery and Energy Reliability MODERN GRID S T R A T E G Y ...

  9. performance metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    people Our People NNSA has the best science, technology and engineering in the world, and we are fortunate to have dedicated professionals who are truly leaders in their fields working every day to promote our nuclear security mission. The people who make up the nuclear security enterprise are on the front lines... Working at NNSA A wide variety of career paths can help you find the type of job that suits your professional goals and lay the groundwork for personal development and career

  10. Performance metrics and life-cycle information management for building performance assurance

    SciTech Connect (OSTI)

    Hitchcock, R.J.; Piette, M.A.; Selkowitz, S.E.

    1998-06-01

    Commercial buildings account for over $85 billion per year in energy costs, which is far more energy than technically necessary. One of the primary reasons buildings do not perform as well as intended is that critical information is lost, through ineffective documentation and communication, leading to building systems that are often improperly installed and operated. A life-cycle perspective on the management of building information provides a framework for improving commercial building energy performance. This paper describes a project to develop strategies and techniques to provide decision-makers with information needed to assure the desired building performance across the complete life cycle of a building project. A key element in this effort is the development of explicit performance metrics that quantitatively represent performance objectives of interest to various building stakeholders. The paper begins with a discussion of key problems identified in current building industry practice, and ongoing work to address these problems. The paper then focuses on the concept of performance metrics and their use in improving building performance during design, commissioning, and on-going operations. The design of a Building Life-cycle Information System (BLISS) is presented. BLISS is intended to provide an information infrastructure capable of integrating a variety of building information technologies that support performance assurance. The use of performance metrics in case study building projects is explored to illustrate current best practice. The application of integrated information technology for improving current practice is discussed.

  11. Specification and implementation of IFC based performance metrics to support building life cycle assessment of hybrid energy systems

    SciTech Connect (OSTI)

    Morrissey, Elmer; O'Donnell, James; Keane, Marcus; Bazjanac, Vladimir

    2004-03-29

    Minimizing building life cycle energy consumption is becoming of paramount importance. Performance metrics tracking offers a clear and concise manner of relating design intent in a quantitative form. A methodology is discussed for storage and utilization of these performance metrics through an Industry Foundation Classes (IFC) instantiated Building Information Model (BIM). The paper focuses on storage of three sets of performance data from three distinct sources. An example of a performance metrics programming hierarchy is displayed for a heat pump and a solar array. Utilizing the sets of performance data, two discrete performance effectiveness ratios may be computed, thus offering an accurate method of quantitatively assessing building performance.

  12. Development and evaluation of aperture-based complexity metrics using film and EPID measurements of static MLC openings

    SciTech Connect (OSTI)

    Götstedt, Julia; Karlsson Hauer, Anna; Bäck, Anna

    2015-07-15

    Purpose: Complexity metrics have been suggested as a complement to measurement-based quality assurance for intensity modulated radiation therapy (IMRT) and volumetric modulated arc therapy (VMAT). However, these metrics have not yet been sufficiently validated. This study develops and evaluates new aperture-based complexity metrics in the context of static multileaf collimator (MLC) openings and compares them to previously published metrics. Methods: This study develops the converted aperture metric and the edge area metric. The converted aperture metric is based on small and irregular parts within the MLC opening that are quantified as measured distances between MLC leaves. The edge area metric is based on the relative size of the region around the edges defined by the MLC. Another metric suggested in this study is the circumference/area ratio. Earlier defined aperture-based complexity metrics—the modulation complexity score, the edge metric, the ratio monitor units (MU)/Gy, the aperture area, and the aperture irregularity—are compared to the newly proposed metrics. A set of small and irregular static MLC openings are created which simulate individual IMRT/VMAT control points of various complexities. These are measured with both an amorphous silicon electronic portal imaging device and EBT3 film. The differences between calculated and measured dose distributions are evaluated using a pixel-by-pixel comparison with two global dose difference criteria of 3% and 5%. The extent of the dose differences, expressed in terms of pass rate, is used as a measure of the complexity of the MLC openings and used for the evaluation of the metrics compared in this study. The different complexity scores are calculated for each created static MLC opening. The correlation between the calculated complexity scores and the extent of the dose differences (pass rate) are analyzed in scatter plots and using Pearson’s r-values. Results: The complexity scores calculated by the edge area metric, converted aperture metric, circumference/area ratio, edge metric, and MU/Gy ratio show good linear correlation to the complexity of the MLC openings, expressed as the 5% dose difference pass rate, with Pearson’s r-values of −0.94, −0.88, −0.84, −0.89, and −0.82, respectively. The overall trends for the 3% and 5% dose difference evaluations are similar. Conclusions: New complexity metrics are developed. The calculated scores correlate to the complexity of the created static MLC openings. The complexity of the MLC opening is dependent on the penumbra region relative to the area of the opening. The aperture-based complexity metrics that combined either the distances between the MLC leaves or the MLC opening circumference with the aperture area show the best correlation with the complexity of the static MLC openings.

  13. Light Water Reactor Sustainability Program Operator Performance Metrics for Control Room Modernization: A Practical Guide for Early Design Evaluation

    SciTech Connect (OSTI)

    Ronald Boring; Roger Lew; Thomas Ulrich; Jeffrey Joe

    2014-03-01

    As control rooms are modernized with new digital systems at nuclear power plants, it is necessary to evaluate the operator performance using these systems as part of a verification and validation process. There are no standard, predefined metrics available for assessing what is satisfactory operator interaction with new systems, especially during the early design stages of a new system. This report identifies the process and metrics for evaluating human system interfaces as part of control room modernization. The report includes background information on design and evaluation, a thorough discussion of human performance measures, and a practical example of how the process and metrics have been used as part of a turbine control system upgrade during the formative stages of design. The process and metrics are geared toward generalizability to other applications and serve as a template for utilities undertaking their own control room modernization activities.

  14. Genome Assembly Forensics: Metrics for Assessing Assembly Correctness (Metagenomics Informatics Challenges Workshop: 10K Genomes at a Time)

    ScienceCinema (OSTI)

    Pop, Mihai [University of Maryland

    2013-01-22

    University of Maryland's Mihai Pop on "Genome Assembly Forensics: Metrics for Assessing Assembly Correctness" at the Metagenomics Informatics Challenges Workshop held at the DOE JGI on October 12-13, 2011.

  15. Einstein-aether theory, violation of Lorentz invariance, and metric-affine gravity

    SciTech Connect (OSTI)

    Heinicke, Christian; Baekler, Peter; Hehl, Friedrich W.

    2005-07-15

    We show that the Einstein-aether theory of Jacobson and Mattingly (J and M) can be understood in the framework of the metric-affine (gauge theory of) gravity (MAG). We achieve this by relating the aether vector field of J and M to certain post-Riemannian nonmetricity pieces contained in an independent linear connection of spacetime. Then, for the aether, a corresponding geometrical curvature-square Lagrangian with a massive piece can be formulated straightforwardly. We find an exact spherically symmetric solution of our model.

  16. Comparing Resource Adequacy Metrics and Their Influence on Capacity Value: Preprint

    SciTech Connect (OSTI)

    Ibanez, E.; Milligan, M.

    2014-04-01

    Traditional probabilistic methods have been used to evaluate resource adequacy. The increasing presence of variable renewable generation in power systems presents a challenge to these methods because, unlike thermal units, variable renewable generation levels change over time because they are driven by meteorological events. Thus, capacity value calculations for these resources are often performed to simple rules of thumb. This paper follows the recommendations of the North American Electric Reliability Corporation?s Integration of Variable Generation Task Force to include variable generation in the calculation of resource adequacy and compares different reliability metrics. Examples are provided using the Western Interconnection footprint under different variable generation penetrations.

  17. Perfect fluid and scalar field in the Reissner-Nordstroem metric

    SciTech Connect (OSTI)

    Babichev, E. O.; Dokuchaev, V. I. Eroshenko, Yu. N.

    2011-05-15

    We describe the spherically symmetric steady-state accretion of perfect fluid in the Reissner-Nordstroem metric. We present analytic solutions for accretion of a fluid with linear equations of state and of the Chaplygin gas. We also show that under reasonable physical conditions, there is no steady-state accretion of a perfect fluid onto a Reissner-Nordstroem naked singularity. Instead, a static atmosphere of fluid is formed. We discuss a possibility of violation of the third law of black hole thermodynamics for a phantom fluid accretion.

  18. Ultrahard fluid and scalar field in the Kerr-Newman metric

    SciTech Connect (OSTI)

    Babichev, E.; Chernov, S.; Dokuchaev, V.; Eroshenko, Yu.

    2008-11-15

    An analytic solution for the accretion of ultrahard perfect fluid onto a moving Kerr-Newman black hole is found. This solution is a generalization of the previously known solution by Petrich, Shapiro, and Teukolsky for a Kerr black hole. We show that the found solution is applicable for the case of a nonextreme black hole, however it cannot describe the accretion onto an extreme black hole due to violation of the test fluid approximation. We also present a stationary solution for a massless scalar field in the metric of a Kerr-Newman naked singularity.

  19. Executive Order 13583, Establishing a Coordinated Government-Wide Initiative to Promote Diversity and Inclusion in the Federal Workforce

    Broader source: Energy.gov [DOE]

    Establishes a "coordinated government-wide initiative to promote diversity and inclusion in the federal workforce".

  20. Semi-inclusive charged-current neutrino-nucleus reactions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Moreno, O.; Donnelly, T. W.; Van Orden, J. W.; Ford, W. P.

    2014-07-17

    The general, universal formalism for semi-inclusive charged-current (anti)neutrino-nucleus reactions is given for studies of any hadronic system, namely, either nuclei or the nucleon itself. The detailed developments are presented with the former in mind and are further specialized to cases where the final-state charged lepton and an ejected nucleon are presumed to be detected. General kinematics for such processes are summarized and then explicit expressions are developed for the leptonic and hadronic tensors involved and for the corresponding responses according to the usual charge, longitudinal and transverse projections, keeping finite the masses of all particles involved. In the case ofmore » the hadronic responses, general symmetry principles are invoked to determine which contributions can occur. As a result, the general leptonic-hadronic tensor contraction is given as well as the cross section for the process.« less

  1. Semi-inclusive charged-current neutrino-nucleus reactions

    SciTech Connect (OSTI)

    Moreno, O.; Donnelly, T. W.; Van Orden, J. W.; Ford, W. P.

    2014-07-17

    The general, universal formalism for semi-inclusive charged-current (anti)neutrino-nucleus reactions is given for studies of any hadronic system, namely, either nuclei or the nucleon itself. The detailed developments are presented with the former in mind and are further specialized to cases where the final-state charged lepton and an ejected nucleon are presumed to be detected. General kinematics for such processes are summarized and then explicit expressions are developed for the leptonic and hadronic tensors involved and for the corresponding responses according to the usual charge, longitudinal and transverse projections, keeping finite the masses of all particles involved. In the case of the hadronic responses, general symmetry principles are invoked to determine which contributions can occur. As a result, the general leptonic-hadronic tensor contraction is given as well as the cross section for the process.

  2. Numerical method for shear bands in ductile metal with inclusions

    SciTech Connect (OSTI)

    Plohr, Jee Yeon N [Los Alamos National Laboratory; Plohr, Bradley J [Los Alamos National Laboratory

    2010-01-01

    A numerical method for mesoscale simulation of high strain-rate loading of ductile metal containing inclusions is described. Because of small-scale inhomogeneities, such a composite material is prone to localized shear deformation (adiabatic shear bands). The modeling framework is the Generalized Method of Cells of Paley and Aboudi [Mech. Materials, vol. 14, pp. /27-139, 1992], which ensures that the micromechanical response of the material is reflected in the behavior of the composite at the mesoscale. To calculate the effective plastic strain rate when shear bands are present, the analytic and numerical analysis of shear bands by Glimm, Plohr, and Sharp [Mech. Materials, vol. 24, pp. 31-41, 1996] is adapted and extended.

  3. Government-Wide Diversity and Inclusion Strategic Plan (2011), Office of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Personnel Management | Department of Energy Government-Wide Diversity and Inclusion Strategic Plan (2011), Office of Personnel Management Government-Wide Diversity and Inclusion Strategic Plan (2011), Office of Personnel Management This document, required by Executive Order 13583, provides a shared direction, encourages commitment, and creates alignment so agencies can approach their workplace diversity and inclusion efforts in a coordinated, collaborative, and integrated manner. Three key

  4. Derivation of a Levelized Cost of Coating (LCOC) metric for evaluation of solar selective absorber materials

    SciTech Connect (OSTI)

    Ho, C. K.; Pacheco, J. E.

    2015-06-05

    A new metric, the Levelized Cost of Coating (LCOC), is derived in this paper to evaluate and compare alternative solar selective absorber coatings against a baseline coating (Pyromark 2500). In contrast to previous metrics that focused only on the optical performance of the coating, the LCOC includes costs, durability, and optical performance for more comprehensive comparisons among candidate materials. The LCOC is defined as the annualized marginal cost of the coating to produce a baseline annual thermal energy production. Costs include the cost of materials and labor for initial application and reapplication of the coating, as well as the cost of additional or fewer heliostats to yield the same annual thermal energy production as the baseline coating. Results show that important factors impacting the LCOC include the initial solar absorptance, thermal emittance, reapplication interval, degradation rate, reapplication cost, and downtime during reapplication. The LCOC can also be used to determine the optimal reapplication interval to minimize the levelized cost of energy production. As a result, similar methods can be applied more generally to determine the levelized cost of component for other applications and systems.

  5. Derivation of a Levelized Cost of Coating (LCOC) metric for evaluation of solar selective absorber materials

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ho, C. K.; Pacheco, J. E.

    2015-06-05

    A new metric, the Levelized Cost of Coating (LCOC), is derived in this paper to evaluate and compare alternative solar selective absorber coatings against a baseline coating (Pyromark 2500). In contrast to previous metrics that focused only on the optical performance of the coating, the LCOC includes costs, durability, and optical performance for more comprehensive comparisons among candidate materials. The LCOC is defined as the annualized marginal cost of the coating to produce a baseline annual thermal energy production. Costs include the cost of materials and labor for initial application and reapplication of the coating, as well as the costmore » of additional or fewer heliostats to yield the same annual thermal energy production as the baseline coating. Results show that important factors impacting the LCOC include the initial solar absorptance, thermal emittance, reapplication interval, degradation rate, reapplication cost, and downtime during reapplication. The LCOC can also be used to determine the optimal reapplication interval to minimize the levelized cost of energy production. As a result, similar methods can be applied more generally to determine the levelized cost of component for other applications and systems.« less

  6. Methodology, Methods, and Metrics for Testing and Evaluating Augmented Cognition Systems

    SciTech Connect (OSTI)

    Greitzer, Frank L.

    2008-09-15

    The augmented cognition research community seeks cognitive neuroscience-based solutions to improve warfighter performance by applying and managing mitigation strategies to reduce workload and improve the throughput and quality of decisions. The focus of augmented cognition mitigation research is to define, demonstrate, and exploit neuroscience and behavioral measures that support inferences about the warfighters cognitive state that prescribe the nature and timing of mitigation. A research challenge is to develop valid evaluation methodologies, metrics and measures to assess the impact of augmented cognition mitigations. Two considerations are external validity, which is the extent to which the results apply to operational contexts; and internal validity, which reflects the reliability of performance measures and the conclusions based on analysis of results. The scientific rigor of the research methodology employed in conducting empirical investigations largely affects the validity of the findings. External validity requirements also compel us to demonstrate operational significance of mitigations. Thus it is important to demonstrate effectiveness of mitigations under specific conditions. This chapter reviews some cognitive science and methodological considerations in designing augmented cognition research studies and associated human performance metrics and analysis methods to assess the impact of augmented cognition mitigations.

  7. Assessing the Effects of Data Compression in Simulations Using Physically Motivated Metrics

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Laney, Daniel; Langer, Steven; Weber, Christopher; Lindstrom, Peter; Wegener, Al

    2014-01-01

    This paper examines whether lossy compression can be used effectively in physics simulations as a possible strategy to combat the expected data-movement bottleneck in future high performance computing architectures. We show that, for the codes and simulations we tested, compression levels of 3–5X can be applied without causing significant changes to important physical quantities. Rather than applying signal processing error metrics, we utilize physics-based metrics appropriate for each code to assess the impact of compression. We evaluate three different simulation codes: a Lagrangian shock-hydrodynamics code, an Eulerian higher-order hydrodynamics turbulence modeling code, and an Eulerian coupled laser-plasma interaction code. Wemore » compress relevant quantities after each time-step to approximate the effects of tightly coupled compression and study the compression rates to estimate memory and disk-bandwidth reduction. We find that the error characteristics of compression algorithms must be carefully considered in the context of the underlying physics being modeled.« less

  8. Chemical Signatures of and Precursors to Fractures Using Fluid Inclusion Stratigraphy

    Broader source: Energy.gov [DOE]

    The purpose of this research is to develop a method to identify fracture systems in wells using fluid inclusion gas analysis of drill chips.

  9. One-pot refolding of core histones from bacterial inclusion bodies...

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Search Results Journal Article: One-pot refolding of core histones from bacterial inclusion bodies allows rapid reconstitution of histone octamer Citation Details ...

  10. SU-E-T-359: Measurement of Various Metrics to Determine Changes in Megavoltage Photon Beam Energy

    SciTech Connect (OSTI)

    Gao, S; Balter, P; Rose, M; Simon, W

    2014-06-01

    Purpose: To examine the relationship between photon beam energy and various metrics for energy on the flattened and flattening filter free (FFF) beams generated by the Varian TrueBeam. Methods: Energy changes were accomplished by adjusting the bending magnet current 10% from the nominal value for the 4, 6, 8, and 10 MV flattened and 6 and 10 MV FFF beams. Profiles were measured for a 3030 cm{sup 2} field using a 2D ionization chamber array and a 3D water Scanner which was also used to measure PDDs. For flattened beams we compared several energy metrics; PDD at 10 cm depth in water (PDD(10)); the variation over the central 80% of the field (Flat); and the average of the highest reading along each diagonal divided by the CAX value, diagonal normalized flatness (FDN). For FFF beams we examined PDD(10), FDN, and the width of a chosen isodose level in a 3030 cm{sup 2} field (W(d%)). Results: Changes in PDD(10) were nearly linear with changes in energy for both flattened and FFF beams as were changes in FDN. Changes in W(d%) were also nearly linear with energy for the FFF beams. PDD(10) was not as sensitive to changes in energy compared to the other metrics for either flattened or FFF beams. Flat was not as sensitive to changes in energy compared to FDN for flattened beams and its behavior depends on depth. FDN was the metric that had the highest sensitivity to the changes in energy for flattened beams while W(d%) was the metric that had highest sensitivity to the changes in energy for FFF beams. Conclusions: The metric FDN was found to be most sensitive to energy changes for flattened beams, while the W(d%) was most sensitive to energy changes for FFF beams.

  11. MULTI-SCALE MORPHOLOGICAL ANALYSIS OF SDSS DR5 SURVEY USING THE METRIC SPACE TECHNIQUE

    SciTech Connect (OSTI)

    Wu Yongfeng; Batuski, David J.; Khalil, Andre

    2009-12-20

    Following the novel development and adaptation of the Metric Space Technique (MST), a multi-scale morphological analysis of the Sloan Digital Sky Survey (SDSS) Data Release 5 (DR5) was performed. The technique was adapted to perform a space-scale morphological analysis by filtering the galaxy point distributions with a smoothing Gaussian function, thus giving quantitative structural information on all size scales between 5 and 250 Mpc. The analysis was performed on a dozen slices of a volume of space containing many newly measured galaxies from the SDSS DR5 survey. Using the MST, observational data were compared to galaxy samples taken from N-body simulations with current best estimates of cosmological parameters and from random catalogs. By using the maximal ranking method among MST output functions, we also develop a way to quantify the overall similarity of the observed samples with the simulated samples.

  12. Anomaly metrics to differentiate threat sources from benign sources in primary vehicle screening.

    SciTech Connect (OSTI)

    Cohen, Israel Dov; Mengesha, Wondwosen

    2011-09-01

    Discrimination of benign sources from threat sources at Port of Entries (POE) is of a great importance in efficient screening of cargo and vehicles using Radiation Portal Monitors (RPM). Currently RPM's ability to distinguish these radiological sources is seriously hampered by the energy resolution of the deployed RPMs. As naturally occurring radioactive materials (NORM) are ubiquitous in commerce, false alarms are problematic as they require additional resources in secondary inspection in addition to impacts on commerce. To increase the sensitivity of such detection systems without increasing false alarm rates, alarm metrics need to incorporate the ability to distinguish benign and threat sources. Principal component analysis (PCA) and clustering technique were implemented in the present study. Such techniques were investigated for their potential to lower false alarm rates and/or increase sensitivity to weaker threat sources without loss of specificity. Results of the investigation demonstrated improved sensitivity and specificity in discriminating benign sources from threat sources.

  13. Quantifying Availability in SCADA Environments Using the Cyber Security Metric MFC

    SciTech Connect (OSTI)

    Aissa, Anis Ben; Rabai, Latifa Ben Arfa; Abercrombie, Robert K; Sheldon, Frederick T; Mili, Ali

    2014-01-01

    Supervisory Control and Data Acquisition (SCADA) systems are distributed networks dispersed over large geographic areas that aim to monitor and control industrial processes from remote areas and/or a centralized location. They are used in the management of critical infrastructures such as electric power generation, transmission and distribution, water and sewage, manufacturing/industrial manufacturing as well as oil and gas production. The availability of SCADA systems is tantamount to assuring safety, security and profitability. SCADA systems are the backbone of the national cyber-physical critical infrastructure. Herein, we explore the definition and quantification of an econometric measure of availability, as it applies to SCADA systems; our metric is a specialization of the generic measure of mean failure cost.

  14. Method and system for assigning a confidence metric for automated determination of optic disc location

    DOE Patents [OSTI]

    Karnowski, Thomas P.; Tobin, Jr., Kenneth W.; Muthusamy Govindasamy, Vijaya Priya; Chaum, Edward

    2012-07-10

    A method for assigning a confidence metric for automated determination of optic disc location that includes analyzing a retinal image and determining at least two sets of coordinates locating an optic disc in the retinal image. The sets of coordinates can be determined using first and second image analysis techniques that are different from one another. An accuracy parameter can be calculated and compared to a primary risk cut-off value. A high confidence level can be assigned to the retinal image if the accuracy parameter is less than the primary risk cut-off value and a low confidence level can be assigned to the retinal image if the accuracy parameter is greater than the primary risk cut-off value. The primary risk cut-off value being selected to represent an acceptable risk of misdiagnosis of a disease having retinal manifestations by the automated technique.

  15. Interval Data Analysis with the Energy Charting and Metrics Tool (ECAM)

    SciTech Connect (OSTI)

    Taasevigen, Danny J.; Katipamula, Srinivas; Koran, William

    2011-07-07

    Analyzing whole building interval data is an inexpensive but effective way to identify and improve building operations, and ultimately save money. Utilizing the Energy Charting and Metrics Tool (ECAM) add-in for Microsoft Excel, building operators and managers can begin implementing changes to their Building Automation System (BAS) after trending the interval data. The two data components needed for full analyses are whole building electricity consumption (kW or kWh) and outdoor air temperature (OAT). Using these two pieces of information, a series of plots and charts and be created in ECAM to monitor the buildings performance over time, gain knowledge of how the building is operating, and make adjustments to the BAS to improve efficiency and start saving money.

  16. Conceptual Framework for Developing Resilience Metrics for the Electricity, Oil, and Gas Sectors in the United States

    SciTech Connect (OSTI)

    Watson, Jean-Paul; Guttromson, Ross; Silva-Monroy, Cesar; Jeffers, Robert; Jones, Katherine; Ellison, James; Rath, Charles; Gearhart, Jared; Jones, Dean; Corbet, Tom; Hanley, Charles; Walker, La Tonya

    2014-09-01

    This report has been written for the Department of Energy’s Energy Policy and Systems Analysis Office to inform their writing of the Quadrennial Energy Review in the area of energy resilience. The topics of measuring and increasing energy resilience are addressed, including definitions, means of measuring, and analytic methodologies that can be used to make decisions for policy, infrastructure planning, and operations. A risk-based framework is presented which provides a standard definition of a resilience metric. Additionally, a process is identified which explains how the metrics can be applied. Research and development is articulated that will further accelerate the resilience of energy infrastructures.

  17. Study of thermal-gradient-induced migration of brine inclusions in salt. Final report

    SciTech Connect (OSTI)

    Olander, D.R.

    1984-08-01

    Natural salt deposits, which are being considered for high-level waste disposal, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine (the all-liquid inclusions) migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms, which is undesirable. Therefore it is important to consider the migration of brine inclusions in salt under imposed temperature gradients to properly evaluate the performance of a future salt repository for nuclear wastes. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is nonlinear. At high axial loads, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, helium, air and argon were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large-ange grain boundaries was observed.

  18. Implementation Guide - Performance Indicators (Metrics ) for Use with DOE O 440.2B, Aviation Management and Safety

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2005-09-19

    The Guide provides information regarding specific provisions of DOE O 440.2B and is intended to be useful in understanding and implementing performance indicators (metrics) required by the Order. Cancels DOE G 440.2B-1. Canceled by DOE N 251.98.

  19. Implementation Guide - Aviation Program Performance Indicators (Metrics) for use with DOE O 440.2B, Aviation Management And Safety

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2002-12-10

    The Guide provides information regarding Departmental expectations on provisions of DOE 440.2B, identifies acceptable methods of implementing Aviation Program Performance Indicators (Metrics) requirements in the Order, and identifies relevant principles and practices by referencing Government and non-Government standards. Canceled by DOE G 440.2B-1A.

  20. Recommendations for mass spectrometry data quality metrics for open access data(corollary to the Amsterdam principles)

    SciTech Connect (OSTI)

    Kingsinger, Christopher R.; Apffel, James; Baker, Mark S.; Bian, Xiaopeng; Borchers, Christoph H.; Bradshaw, Ralph A.; Brusniak, Mi-Youn; Chan, Daniel W.; Deutsch, Eric W.; Domon, Bruno; Gorman, Jeff; Grimm, Rudolf; Hancock, William S.; Hermjakob, Henning; Horn, David; Hunter, Christie; Kolar, Patrik; Kraus, Hans-Joachim; Langen, Hanno; Linding, Rune; Moritz, Robert L.; Omenn, Gilbert S.; Orlando, Ron; Pandey, Akhilesh; Ping, Peipei; Rahbar, Amir; Rivers, Robert; Seymour, Sean L.; Simpson, Richard J.; Slotta, Douglas; Smith, Richard D.; Stein, Stephen E.; Tabb, David L.; Tagle, Danilo; Yates, John R.; Rodriguez, Henry

    2011-12-01

    Policies supporting the rapid and open sharing of proteomic data are being implemented by the leading journals in the field. The proteomics community is taking steps to ensure that data are made publicly accessible and are of high quality, a challenging task that requires the development and deployment of methods for measuring and documenting data quality metrics. On September 18, 2010, the U.S. National Cancer Institute (NCI) convened the 'International Workshop on Proteomic Data Quality Metrics' in Sydney, Australia, to identify and address issues facing the development and use of such methods for open access proteomics data. The stakeholders at the workshop enumerated the key principles underlying a framework for data quality assessment in mass spectrometry data that will meet the needs of the search community, journals, funding agencies, and data repositories. Attendees discussed and agreed upon two primary needs for the wide use of quality metrics: (i)an evolving list of comprehensive quality metrics and (ii)standards accompanied by software analytics. Attendees stressed the importance of increased education and training programs to promote reliable protocols in proteomics. This workshop report explores the historic precedents, key discussions, and necessary next steps to enhance the quality of open access data. By agreement, this article is published simultaneously in Proteomics, Proteomics Clinical Applications, Journal of Proteome Research, and Molecular and Cellular Proteomics, as a public service to the research community.The peer review process was a coordinated effort conducted by a panel of referees selected by the journals.

  1. Use of Frequency Response Metrics to Assess the Planning and Operating Requirements for Reliable Integration of Variable Renewable Generation

    SciTech Connect (OSTI)

    Eto, Joseph H.; Undrill, John; Mackin, Peter; Daschmans, Ron; Williams, Ben; Haney, Brian; Hunt, Randall; Ellis, Jeff; Illian, Howard; Martinez, Carlos; O'Malley, Mark; Coughlin, Katie; LaCommare, Kristina Hamachi

    2010-12-20

    An interconnected electric power system is a complex system that must be operated within a safe frequency range in order to reliably maintain the instantaneous balance between generation and load. This is accomplished by ensuring that adequate resources are available to respond to expected and unexpected imbalances and restoring frequency to its scheduled value in order to ensure uninterrupted electric service to customers. Electrical systems must be flexible enough to reliably operate under a variety of"change" scenarios. System planners and operators must understand how other parts of the system change in response to the initial change, and need tools to manage such changes to ensure reliable operation within the scheduled frequency range. This report presents a systematic approach to identifying metrics that are useful for operating and planning a reliable system with increased amounts of variable renewable generation which builds on existing industry practices for frequency control after unexpected loss of a large amount of generation. The report introduces a set of metrics or tools for measuring the adequacy of frequency response within an interconnection. Based on the concept of the frequency nadir, these metrics take advantage of new information gathering and processing capabilities that system operators are developing for wide-area situational awareness. Primary frequency response is the leading metric that will be used by this report to assess the adequacy of primary frequency control reserves necessary to ensure reliable operation. It measures what is needed to arrest frequency decline (i.e., to establish frequency nadir) at a frequency higher than the highest set point for under-frequency load shedding within an interconnection. These metrics can be used to guide the reliable operation of an interconnection under changing circumstances.

  2. Inclusive hadron distributions in p+p collisions from saturation models of HERA DIS data.

    SciTech Connect (OSTI)

    Tribedy, P.; Venugopalan, R.

    2010-12-06

    Dipole models based on various saturation scenarios provide reasonable fits to small-x DIS inclusive, diffractive and exclusive data from HERA. Proton un-integrated gluon distributions extracted from such fits are employed in a k{sub {perpendicular}}-factorization framework to calculate inclusive gluon distributions at various energies. The n-particle multiplicity distribution predicted in the Glasma flux tube approach shows good agreement with data over a wide range of energies. Hadron inclusive transverse momentum distributions expressed in terms of the saturation scale demonstrate universal behavior over a wider kinematic range systematically with increasing center of mass energies.

  3. Inclusive charm production in {upsilon}(nS) decay (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Inclusive charm production in {upsilon}(nS) decay Citation Details In-Document Search Title: Inclusive charm production in {upsilon}(nS) decay Based on the nonrelativistic QCD (NRQCD) factorization formalism, we calculate the inclusive charm production rate in {upsilon}(nS) decay at leading order in the strong coupling constant {alpha}{sub s} and the relative velocity v of the b quark in the quarkonium rest frame. The branching fractions for {upsilon}(nS) to charm for n=1, 2,

  4. Single transverse-spin asymmetry for D-meson production in semi-inclusive

    Office of Scientific and Technical Information (OSTI)

    deep inelastic scattering (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: Single transverse-spin asymmetry for D-meson production in semi-inclusive deep inelastic scattering Citation Details In-Document Search Title: Single transverse-spin asymmetry for D-meson production in semi-inclusive deep inelastic scattering We study the single transverse-spin asymmetry for open charm production in the semi-inclusive lepton-hadron deep inelastic scattering. We

  5. An FTIR Study of Hydrogen in Anorthosite and Associated Melt Inclusions

    SciTech Connect (OSTI)

    Seaman,S.; Dyar, M.; Marinkovic, N.; Dunbar, N.

    2006-01-01

    High-resolution Fourier transform infrared (FTIR) spectroscopy has been used to document the presence of hydrogen, to estimate its concentration, and to document its oxygen speciation in anorthoclase crystals and associated melt inclusions from Mount Erebus, Antarctica. Synchrotron-generated infrared radiation, 100 to 1000 times brighter than globar-generated infrared radiation, permits rapid collection of maps that depict relative intensities of a chosen FTIR band across the mapped area. Spectra and/or compositional maps showing variations in water concentration were collected from anorthoclase megacrysts and melt inclusions in the megacrysts. Studies of anorthoclase megacrysts involved collection of spectra from three mutually perpendicular sections cut from the crystals. FTIR spectra of anorthoclase crystals are characterized by a broad absorption band at approximately 3200 cm{sup -1} in the mid-IR range. The universal mass absorption coefficient for mid-IR range feldspar spectra, established by Johnson and Rossman (2003), was used for quantitative estimates of water concentrations in the feldspar crystals based on integrated area under the 3200 cm{sup -1} band. Water concentration in the anorthoclase sample was approximately 126 ppm, with an overall error of approximately {+-}30%. FTIR spectra of melt inclusions are characterized by a broad asymmetric absorption band at {approx}3550 cm{sup -1} that was used to calculate total water concentration. The absence of a band at 1630 cm{sup -1} suggests that water in the melt inclusions occurs as OH{sup -} rather than as molecular H{sub 2}O. Absorption coefficients established by Mandeville et al. (2002) for H species in glass were used to calculate water concentrations in the melt inclusions. Melt inclusions in the Mt. Erebus anorthoclase have water concentrations ranging from 0.12 to 0.39 wt%, with an overall error of approximately {+-}15%. The ratio of water in anorthoclase crystals to water in the melt from which the crystals formed, based on this study, and at these low melt water concentrations, is approximately 1:10. However, water concentration varies significantly from one melt inclusion to another, possibly suggesting initial melt water heterogeneity. Maps of water concentration show that variations in water concentration within melt inclusions are associated with fractures that cut the melt inclusions and in some cases do not extend out into surrounding crystals or into crystal inclusions. Thin ({approx}50 {micro}m thick) zones of elevated water concentrations on the boundaries of the crystals in contact with melt inclusions suggest that water has diffused into the crystals from the melt inclusions.

  6. DOE Ups the Ante for Diversity and Inclusion at the Department of Energy |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy DOE Ups the Ante for Diversity and Inclusion at the Department of Energy DOE Ups the Ante for Diversity and Inclusion at the Department of Energy April 17, 2012 - 8:25am Addthis DOE Ups the Ante for Diversity and Inclusion at the Department of Energy Bill Valdez Bill Valdez Director of Workforce Management "We will treat our people as our greatest asset." This phrase is not only one of DOE's management principles, but it is also the rock behind our new

  7. Evaluation of metrics and baselines for tracking greenhouse gas emissions trends: Recommendations for the California climate action registry

    SciTech Connect (OSTI)

    Price, Lynn; Murtishaw, Scott; Worrell, Ernst

    2003-06-01

    Executive Summary: The California Climate Action Registry, which was initially established in 2000 and began operation in Fall 2002, is a voluntary registry for recording annual greenhouse gas (GHG) emissions. The purpose of the Registry is to assist California businesses and organizations in their efforts to inventory and document emissions in order to establish a baseline and to document early actions to increase energy efficiency and decrease GHG emissions. The State of California has committed to use its ''best efforts'' to ensure that entities that establish GHG emissions baselines and register their emissions will receive ''appropriate consideration under any future international, federal, or state regulatory scheme relating to greenhouse gas emissions.'' Reporting of GHG emissions involves documentation of both ''direct'' emissions from sources that are under the entity's control and indirect emissions controlled by others. Electricity generated by an off-site power source is consider ed to be an indirect GHG emission and is required to be included in the entity's report. Registry participants include businesses, non-profit organizations, municipalities, state agencies, and other entities. Participants are required to register the GHG emissions of all operations in California, and are encouraged to report nationwide. For the first three years of participation, the Registry only requires the reporting of carbon dioxide (CO2) emissions, although participants are encouraged to report the remaining five Kyoto Protocol GHGs (CH4, N2O, HFCs, PFCs, and SF6). After three years, reporting of all six Kyoto GHG emissions is required. The enabling legislation for the Registry (SB 527) requires total GHG emissions to be registered and requires reporting of ''industry-specific metrics'' once such metrics have been adopted by the Registry. The Ernest Orlando Lawrence Berkeley National Laboratory (Berkeley Lab) was asked to provide technical assistance to the California Energy Commission (Energy Commission) related to the Registry in three areas: (1) assessing the availability and usefulness of industry-specific metrics, (2) evaluating various methods for establishing baselines for calculating GHG emissions reductions related to specific actions taken by Registry participants, and (3) establishing methods for calculating electricity CO2 emission factors. The third area of research was completed in 2002 and is documented in Estimating Carbon Dioxide Emissions Factors for the California Electric Power Sector (Marnay et al., 2002). This report documents our findings related to the first areas of research. For the first area of research, the overall objective was to evaluate the metrics, such as emissions per economic unit or emissions per unit of production that can be used to report GHG emissions trends for potential Registry participants. This research began with an effort to identify methodologies, benchmarking programs, inventories, protocols, and registries that u se industry-specific metrics to track trends in energy use or GHG emissions in order to determine what types of metrics have already been developed. The next step in developing industry-specific metrics was to assess the availability of data needed to determine metric development priorities. Berkeley Lab also determined the relative importance of different potential Registry participant categories in order to asses s the availability of sectoral or industry-specific metrics and then identified industry-specific metrics in use around the world. While a plethora of metrics was identified, no one metric that adequately tracks trends in GHG emissions while maintaining confidentiality of data was identified. As a result of this review, Berkeley Lab recommends the development of a GHG intensity index as a new metric for reporting and tracking GHG emissions trends.Such an index could provide an industry-specific metric for reporting and tracking GHG emissions trends to accurately reflect year to year changes while protecting proprietary data. This GHG intensity index changes while protecting proprietary data. This GHG intensity index would provide Registry participants with a means for demonstrating improvements in their energy and GHG emissions per unit of production without divulging specific values. For the second research area, Berkeley Lab evaluated various methods used to calculate baselines for documentation of energy consumption or GHG emissions reductions, noting those that use industry-specific metrics. Accounting for actions to reduce GHGs can be done on a project-by-project basis or on an entity basis. Establishing project-related baselines for mitigation efforts has been widely discussed in the context of two of the so-called ''flexible mechanisms'' of the Kyoto Protocol to the United Nations Framework Convention on Climate Change (Kyoto Protocol) Joint Implementation (JI) and the Clean Development Mechanism (CDM).

  8. New risk metrics and mathematical tools for risk analysis: Current and future challenges

    SciTech Connect (OSTI)

    Skandamis, Panagiotis N. Andritsos, Nikolaos Psomas, Antonios Paramythiotis, Spyridon

    2015-01-22

    The current status of the food safety supply world wide, has led Food and Agriculture Organization (FAO) and World Health Organization (WHO) to establishing Risk Analysis as the single framework for building food safety control programs. A series of guidelines and reports that detail out the various steps in Risk Analysis, namely Risk Management, Risk Assessment and Risk Communication is available. The Risk Analysis approach enables integration between operational food management systems, such as Hazard Analysis Critical Control Points, public health and governmental decisions. To do that, a series of new Risk Metrics has been established as follows: i) the Appropriate Level of Protection (ALOP), which indicates the maximum numbers of illnesses in a population per annum, defined by quantitative risk assessments, and used to establish; ii) Food Safety Objective (FSO), which sets the maximum frequency and/or concentration of a hazard in a food at the time of consumption that provides or contributes to the ALOP. Given that ALOP is rather a metric of the public health tolerable burden (it addresses the total failure that may be handled at a national level), it is difficult to be interpreted into control measures applied at the manufacturing level. Thus, a series of specific objectives and criteria for performance of individual processes and products have been established, all of them assisting in the achievement of FSO and hence, ALOP. In order to achieve FSO, tools quantifying the effect of processes and intrinsic properties of foods on survival and growth of pathogens are essential. In this context, predictive microbiology and risk assessment have offered an important assistance to Food Safety Management. Predictive modelling is the basis of exposure assessment and the development of stochastic and kinetic models, which are also available in the form of Web-based applications, e.g., COMBASE and Microbial Responses Viewer), or introduced into user-friendly softwares, (e.g., Seafood Spoilage Predictor) have evolved the use of information systems in the food safety management. Such tools are updateable with new food-pathogen specific models containing cardinal parameters and multiple dependent variables, including plate counts, concentration of metabolic products, or even expression levels of certain genes. Then, these tools may further serve as decision-support tools which may assist in product logistics, based on their scientifically-based and momentary expressed spoilage and safety level.

  9. Methodological Framework for Analysis of Buildings-Related Programs: The GPRA Metrics Effort

    SciTech Connect (OSTI)

    Elliott, Douglas B.; Anderson, Dave M.; Belzer, David B.; Cort, Katherine A.; Dirks, James A.; Hostick, Donna J.

    2004-06-18

    The requirements of the Government Performance and Results Act (GPRA) of 1993 mandate the reporting of outcomes expected to result from programs of the Federal government. The U.S. Department of Energy’s (DOE’s) Office of Energy Efficiency and Renewable Energy (EERE) develops official metrics for its 11 major programs using its Office of Planning, Budget Formulation, and Analysis (OPBFA). OPBFA conducts an annual integrated modeling analysis to produce estimates of the energy, environmental, and financial benefits expected from EERE’s budget request. Two of EERE’s major programs include the Building Technologies Program (BT) and Office of Weatherization and Intergovernmental Program (WIP). Pacific Northwest National Laboratory (PNNL) supports the OPBFA effort by developing the program characterizations and other market information affecting these programs that is necessary to provide input to the EERE integrated modeling analysis. Throughout the report we refer to these programs as “buildings-related” programs, because the approach is not limited in application to BT or WIP. To adequately support OPBFA in the development of official GPRA metrics, PNNL communicates with the various activities and projects in BT and WIP to determine how best to characterize their activities planned for the upcoming budget request. PNNL then analyzes these projects to determine what the results of the characterizations would imply for energy markets, technology markets, and consumer behavior. This is accomplished by developing nonintegrated estimates of energy, environmental, and financial benefits (i.e., outcomes) of the technologies and practices expected to result from the budget request. These characterizations and nonintegrated modeling results are provided to OPBFA as inputs to the official benefits estimates developed for the Federal Budget. This report documents the approach and methodology used to estimate future energy, environmental, and financial benefits produced by technologies and practices supported by BT and by WIP. However, the approach is general enough for analysis of buildings-related technologies, independent of any specific program. An overview describes the GPRA process and the models used to estimate energy savings. The body of the document describes the algorithms used and the diffusion curve estimates.

  10. The International Safeguards Technology Base: How is the Patient Doing? An Exploration of Effective Metrics

    SciTech Connect (OSTI)

    Schanfein, Mark; Gouveia, Fernando; Crawford, Cary E.; Pickett, Chris J.; Jay, Jeffrey

    2010-07-15

    The term “Technology Base” is commonly used but what does it mean? Is there a common understanding of the components that comprise a technology base? Does a formal process exist to assess the health of a given technology base? These are important questions the relevance of which is even more pressing given the USDOE/NNSA initiatives to strengthen the safeguards technology base through investments in research & development and human capital development. Accordingly, the authors will establish a high-level framework to define and understand what comprises a technology base. Potential goal-driven metrics to assess the health of a technology base will also be explored, such as linear demographics and resource availability, in the hope that they can be used to better understand and improve the health of the U.S. safeguards technology base. Finally, through the identification of such metrics, the authors will offer suggestions and highlight choices for addressing potential shortfalls. Introduction The U.S. safeguards technology base got its start almost half a century ago in the nuclear weapons program of the U.S. Department of Energy/National Nuclear Security Administration (DOE/NNSA) and their predecessors: AEC & ERDA. Due to nuclear materials’ strategic importance and value, and the risk associated with the public’s and worker’s health and the potential for theft, significant investments were made to develop techniques to measure nuclear materials using both destructive assay (DA) and non-destructive assay (NDA). Major investment within the U.S. DOE Domestic Safeguards Program continued over the next three decades, resulting in continuous improvements in the state-of-the-art of these techniques. This was particularly true in the area of NDA with its ability to use gamma rays, neutrons, and heat to identify and quantify nuclear materials without the need to take direct samples of the material. Most of these techniques were commercialized and transferred to industry, opening their applications to the nuclear industry worldwide and to the International Atomic Energy Agency (IAEA).

  11. Fermilab Today

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    shows the volume taken up by one metric ton of carbon dioxide. In 2013, the United States emitted the equivalent of 6.7 billion metric tons. By tracking how much greenhouse...

  12. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",101093,13 " Nitrogen oxide (short tons)",23993,32 " Carbon dioxide (thousand metric tons)",24037,33 " Sulfur dioxide (lbsMWh)",3.7,5 " Nitrogen oxide (lbsMWh)",0.9,37 ...

  13. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",332396,3 " Nitrogen oxide (short tons)",133412,3 " Carbon dioxide (thousand metric tons)",103391,3 " Sulfur dioxide (lbsMWh)",5.8,1 " Nitrogen oxide (lbsMWh)",2.3,8 ...

  14. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",31550,29 " Nitrogen oxide (short tons)",29014,29 " Carbon dioxide (thousand metric tons)",31794,29 " Sulfur dioxide (lbsMWh)",1.3,29 " Nitrogen oxide (lbs...

  15. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",14426,34 " Nitrogen oxide (short tons)",20538,36 " Carbon dioxide (thousand metric tons)",17678,36 " Sulfur dioxide (lbsMWh)",1,34 " Nitrogen oxide (lbsMWh)",1.4,21 ...

  16. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",10990,38 " Nitrogen oxide (short tons)",8622,46 " Carbon dioxide (thousand metric tons)",3298,46 " Sulfur dioxide (lbsMWh)",1.7,25 " Nitrogen oxide (lbsMWh)",1.3,23 ...

  17. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",3842005 " Nitrogen oxide (short tons)",2400375 " Carbon dioxide (thousand metric tons)",2160342 " Sulfur dioxide (lbsMWh)",1.9 " Nitrogen oxide (lbsMWh)",1.2 " ...

  18. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",22597,32 " Nitrogen oxide (short tons)",56726,17 " Carbon dioxide (thousand metric tons)",53684,16 " Sulfur dioxide (lbsMWh)",0.4,41 " Nitrogen oxide (lbsMWh)",1,33 ...

  19. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",28453,30 " Nitrogen oxide (short tons)",44349,24 " Carbon dioxide (thousand metric tons)",38474,22 " Sulfur dioxide (lbsMWh)",1.1,32 " Nitrogen oxide (lbs...

  20. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",31878,28 " Nitrogen oxide (short tons)",46971,21 " Carbon dioxide (thousand metric tons)",33240,26 " Sulfur dioxide (lbsMWh)",0.5,39 " Nitrogen oxide (lbs...

  1. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",10229,40 " Nitrogen oxide (short tons)",18606,39 " Carbon dioxide (thousand metric tons)",16222,37 " Sulfur dioxide (lbsMWh)",0.6,38 " Nitrogen oxide (lbsMWh)",1,32 ...

  2. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",23646,31 " Nitrogen oxide (short tons)",57944,16 " Carbon dioxide (thousand metric tons)",35179,24 " Sulfur dioxide (lbsMWh)",1.1,31 " Nitrogen oxide (lbsMWh)",2.6,7 ...

  3. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",824,48 " Nitrogen oxide (short tons)",2836,48 " Carbon dioxide (thousand metric tons)",4276,43 " Sulfur dioxide (lbsMWh)",0.2,45 " Nitrogen oxide (lbsMWh)",0.7,40 ...

  4. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",173521,7 " Nitrogen oxide (short tons)",77950,9 " Carbon dioxide (thousand metric tons)",64062,11 " Sulfur dioxide (lbsMWh)",3.2,7 " Nitrogen oxide (lbsMWh)",1.5,19 ...

  5. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",5777,42 " Nitrogen oxide (short tons)",20301,37 " Carbon dioxide (thousand metric tons)",1492,49 " Sulfur dioxide (lbsMWh)",0.8,36 " Nitrogen oxide (lbsMWh)",2.7,5 ...

  6. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",204873,5 " Nitrogen oxide (short tons)",89253,7 " Carbon dioxide (thousand metric tons)",85795,7 " Sulfur dioxide (lbsMWh)",4.5,3 " Nitrogen oxide (lbsMWh)",2,10 " ...

  7. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",96240,14 " Nitrogen oxide (short tons)",83112,8 " Carbon dioxide (thousand metric tons)",57137,15 " Sulfur dioxide (lbsMWh)",1.8,21 " Nitrogen oxide (lbsMWh)",1.6,15 ...

  8. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",63994,22 " Nitrogen oxide (short tons)",27045,30 " Carbon dioxide (thousand metric tons)",26348,31 " Sulfur dioxide (lbsMWh)",3.2,8 " Nitrogen oxide (lbsMWh)",1.4,20 ...

  9. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",74422,19 " Nitrogen oxide (short tons)",41793,25 " Carbon dioxide (thousand metric tons)",39312,21 " Sulfur dioxide (lbsMWh)",2.6,13 " Nitrogen oxide (lbs...

  10. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",41370,26 " Nitrogen oxide (short tons)",20626,35 " Carbon dioxide (thousand metric tons)",20414,34 " Sulfur dioxide (lbsMWh)",2.2,18 " Nitrogen oxide (lbs...

  11. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",355108,1 " Nitrogen oxide (short tons)",105688,4 " Carbon dioxide (thousand metric tons)",98650,5 " Sulfur dioxide (lbsMWh)",5.3,2 " Nitrogen oxide (lbsMWh)",1.6,16 ...

  12. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",6748,41 " Nitrogen oxide (short tons)",13831,43 " Carbon dioxide (thousand metric tons)",12231,39 " Sulfur dioxide (lbsMWh)",0.4,40 " Nitrogen oxide (lbs...

  13. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",21670,33 " Nitrogen oxide (short tons)",26928,31 " Carbon dioxide (thousand metric tons)",7313,42 " Sulfur dioxide (lbsMWh)",4.2,4 " Nitrogen oxide (lbsMWh)",5.3,2 ...

  14. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",297598,4 " Nitrogen oxide (short tons)",141486,2 " Carbon dioxide (thousand metric tons)",101361,4 " Sulfur dioxide (lbsMWh)",2.7,11 " Nitrogen oxide (lbs...

  15. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",10595,39 " Nitrogen oxide (short tons)",14313,42 " Carbon dioxide (thousand metric tons)",8334,40 " Sulfur dioxide (lbsMWh)",0.4,42 " Nitrogen oxide (lbsMWh)",0.5,45 ...

  16. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",349245,2 " Nitrogen oxide (short tons)",229580,1 " Carbon dioxide (thousand metric tons)",254488,1 " Sulfur dioxide (lbsMWh)",1.6,26 " Nitrogen oxide (lbsMWh)",1,31 ...

  17. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",149842,9 " Nitrogen oxide (short tons)",77749,10 " Carbon dioxide (thousand metric tons)",75735,8 " Sulfur dioxide (lbsMWh)",3.4,6 " Nitrogen oxide (lbsMWh)",1.8,13 ...

  18. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",89357,16 " Nitrogen oxide (short tons)",23913,33 " Carbon dioxide (thousand metric tons)",41405,20 " Sulfur dioxide (lbsMWh)",2.2,16 " Nitrogen oxide (lbs...

  19. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",0,51 " Nitrogen oxide (short tons)",147,51 " Carbon dioxide (thousand metric tons)",48,50 " Sulfur dioxide (lbsMWh)",0,51 " Nitrogen oxide (lbsMWh)",4.3,3 " ...

  20. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",52716,23 " Nitrogen oxide (short tons)",48711,19 " Carbon dioxide (thousand metric tons)",30420,30 " Sulfur dioxide (lbsMWh)",2.9,10 " Nitrogen oxide (lbsMWh)",2.7,6 ...

  1. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",100,49 " Nitrogen oxide (short tons)",1224,49 " Carbon dioxide (thousand metric tons)",2566,48 " Sulfur dioxide (lbsMWh)",0,48 " Nitrogen oxide (lbsMWh)",0.4,49 ...

  2. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",64168,21 " Nitrogen oxide (short tons)",67534,12 " Carbon dioxide (thousand metric tons)",58578,13 " Sulfur dioxide (lbsMWh)",1,33 " Nitrogen oxide (lbsMWh)",1.1,30 ...

  3. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",126600,10 " Nitrogen oxide (short tons)",91356,6 " Carbon dioxide (thousand metric tons)",111549,2 " Sulfur dioxide (lbsMWh)",1.1,30 " Nitrogen oxide (lbsMWh)",0.8,39 ...

  4. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    (short tons)",3102,46 " Nitrogen oxide (short tons)",98348,5 " Carbon dioxide (thousand metric tons)",57223,14 " Sulfur dioxide (lbsMWh)",0,49 " Nitrogen oxide (lbsMWh)",1,34 " ...

  5. "Sources: U.S. Energy Information Administration, Form EIA-860...

    U.S. Energy Information Administration (EIA) Indexed Site

    tons)",105998,11 " Nitrogen oxide (short tons)",58144,14 " Carbon dioxide (thousand metric tons)",62516,12 " Sulfur dioxide (lbsMWh)",1.7,24 " Nitrogen oxide (lbs...

  6. Advanced Fuels Campaign Light Water Reactor Accident Tolerant Fuel Performance Metrics Executive Summary

    SciTech Connect (OSTI)

    Shannon Bragg-Sitton

    2014-02-01

    Research and development (R&D) activities on advanced, higher performance Light Water Reactor (LWR) fuels have been ongoing for the last few years. Following the unfortunate March 2011 events at the Fukushima Nuclear Power Plant in Japan, the R&D shifted toward enhancing the accident tolerance of LWRs. Qualitative attributes for fuels with enhanced accident tolerance, such as improved reaction kinetics with steam resulting in slower hydrogen generation rate, provide guidance for the design and development of fuels and cladding with enhanced accident tolerance. A common set of technical metrics should be established to aid in the optimization and down selection of candidate designs on a more quantitative basis. “Metrics” describe a set of technical bases by which multiple concepts can be fairly evaluated against a common baseline and against one another. This report describes a proposed technical evaluation methodology that can be applied to evaluate the ability of each concept to meet performance and safety goals relative to the current UO2 – zirconium alloy system and relative to one another. The resultant ranked evaluation can then inform concept down-selection, such that the most promising accident tolerant fuel design option(s) can continue to be developed toward qualification.

  7. ZFS on RBODs - Leveraging RAID Controllers for Metrics and Enclosure Management

    SciTech Connect (OSTI)

    Stearman, D. M.

    2015-03-30

    Traditionally, the Lustre file system has relied on the ldiskfs file system with reliable RAID (Redundant Array of Independent Disks) storage underneath. As of Lustre 2.4, ZFS was added as a backend file system, with built-in software RAID, thereby removing the need of expensive RAID controllers. ZFS was designed to work with JBOD (Just a Bunch Of Disks) storage enclosures under the Solaris Operating System, which provided a rich device management system. Long time users of the Lustre file system have relied on the RAID controllers to provide metrics and enclosure monitoring and management services, with rich APIs and command line interfaces. This paper will study a hybrid approach using an advanced full featured RAID enclosure which is presented to the host as a JBOD, This RBOD (RAIDed Bunch Of Disks) allows ZFS to do the RAID protection and error correction, while the RAID controller handles management of the disks and monitors the enclosure. It was hoped that the value of the RAID controller features would offset the additional cost, and that performance would not suffer in this mode. The test results revealed that the hybrid RBOD approach did suffer reduced performance.

  8. Application Of Fluid Inclusion And Rock-Gas Analysis In Mineral...

    Open Energy Info (EERE)

    to analyze these gases in fluid inclusions in jasperoid around the Pueblo Viejo gold-silver deposit, in vein minerals from the Creede silver-lead-zinc deposit, and from...

  9. U.S. Office of Personnel Management, Office of Diversity and Inclusion

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Government-Wide Diversity and Inclusion Strategic Plan 2011 Our Nation derives strength from the diversity of its population and from its commitment to equal opportunity for all. We are at our best when we draw on the talents of all parts of our society, and our greatest accomplishments are achieved when diverse perspectives are brought to bear to overcome our greatest challenges. - President Obama, Executive Order 13583 U.S. Office of Personnel Management Office of Diversity and Inclusion 2

  10. Distorted spin dependent spectral function of {sup 3}He and semi-inclusive

    Office of Scientific and Technical Information (OSTI)

    deep inelastic scattering processes (Journal Article) | SciTech Connect Distorted spin dependent spectral function of {sup 3}He and semi-inclusive deep inelastic scattering processes Citation Details In-Document Search Title: Distorted spin dependent spectral function of {sup 3}He and semi-inclusive deep inelastic scattering processes The spin dependent spectral function, relevant to describe polarized electron scattering off polarized {sup 3}He, is studied, within the Plane Wave Impulse

  11. One-pot refolding of core histones from bacterial inclusion bodies allows

    Office of Scientific and Technical Information (OSTI)

    rapid reconstitution of histone octamer (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: One-pot refolding of core histones from bacterial inclusion bodies allows rapid reconstitution of histone octamer Citation Details In-Document Search Title: One-pot refolding of core histones from bacterial inclusion bodies allows rapid reconstitution of histone octamer Authors: Lee, Young-Tae ; Gibbons, Garrett ; Lee, Shirley Y. ; Nikolovska-Coleska, Zaneta ; Dou, Yali

  12. Energy Department Finalizes $1.2 Billion Loan Guarantee to Support California Solar Generation

    Broader source: Energy.gov [DOE]

    Project funds more than 350 jobs and avoids more than 425,000 metric tons of carbon dioxide annually

  13. Simulation information regarding Sandia National Laboratories%3CU%2B2019%3E trinity capability improvement metric.

    SciTech Connect (OSTI)

    Agelastos, Anthony Michael; Lin, Paul T.

    2013-10-01

    Sandia National Laboratories, Los Alamos National Laboratory, and Lawrence Livermore National Laboratory each selected a representative simulation code to be used as a performance benchmark for the Trinity Capability Improvement Metric. Sandia selected SIERRA Low Mach Module: Nalu, which is a uid dynamics code that solves many variable-density, acoustically incompressible problems of interest spanning from laminar to turbulent ow regimes, since it is fairly representative of implicit codes that have been developed under ASC. The simulations for this metric were performed on the Cielo Cray XE6 platform during dedicated application time and the chosen case utilized 131,072 Cielo cores to perform a canonical turbulent open jet simulation within an approximately 9-billion-elementunstructured- hexahedral computational mesh. This report will document some of the results from these simulations as well as provide instructions to perform these simulations for comparison.

  14. Effective detective quantum efficiency for two mammography systems: Measurement and comparison against established metrics

    SciTech Connect (OSTI)

    Salvagnini, Elena; Bosmans, Hilde; Marshall, Nicholas W.; Struelens, Lara

    2013-10-15

    Purpose: The aim of this paper was to illustrate the value of the new metric effective detective quantum efficiency (eDQE) in relation to more established measures in the optimization process of two digital mammography systems. The following metrics were included for comparison against eDQE: detective quantum efficiency (DQE) of the detector, signal difference to noise ratio (SdNR), and detectability index (d′) calculated using a standard nonprewhitened observer with eye filter.Methods: The two systems investigated were the Siemens MAMMOMAT Inspiration and the Hologic Selenia Dimensions. The presampling modulation transfer function (MTF) required for the eDQE was measured using two geometries: a geometry containing scattered radiation and a low scatter geometry. The eDQE, SdNR, and d′ were measured for poly(methyl methacrylate) (PMMA) thicknesses of 20, 40, 60, and 70 mm, with and without the antiscatter grid and for a selection of clinically relevant target/filter (T/F) combinations. Figures of merit (FOMs) were then formed from SdNR and d′ using the mean glandular dose as the factor to express detriment. Detector DQE was measured at energies covering the range of typical clinically used spectra.Results: The MTF measured in the presence of scattered radiation showed a large drop at low spatial frequency compared to the low scatter method and led to a corresponding reduction in eDQE. The eDQE for the Siemens system at 1 mm{sup −1} ranged between 0.15 and 0.27, depending on T/F and grid setting. For the Hologic system, eDQE at 1 mm{sup −1} varied from 0.15 to 0.32, again depending on T/F and grid setting. The eDQE results for both systems showed that the grid increased the system efficiency for PMMA thicknesses of 40 mm and above but showed only small sensitivity to T/F setting. While results of the SdNR and d′ based FOMs confirmed the eDQE grid position results, they were also more specific in terms of T/F selection. For the Siemens system at 20 mm PMMA, the FOMs indicated Mo/Mo (grid out) as optimal while W/Rh (grid in) was the optimal configuration at 40, 60, and 70 mm PMMA. For the Hologic, the FOMs pointed to W/Rh (grid in) at 20 and 40 mm of PMMA while W/Ag (grid in) gave the highest FOM at 60 and 70 mm PMMA. Finally, DQE at 1 mm{sup −1} averaged for the four beam qualities studied was 0.44 ± 0.02 and 0.55 ± 0.03 for the Siemens and Hologic detectors, respectively, indicating only a small influence of energy on detector DQE.Conclusions: Both the DQE and eDQE data showed only a small sensitivity to T/F setting for these two systems. The eDQE showed clear preferences in terms of scatter reduction, being highest for the grid-in geometry for PMMA thicknesses of 40 mm and above. The SdNR and d′ based figures of merit, which contain additional weighting for contrast and dose, pointed to specific T/F settings for both systems.

  15. Advanced Fuels Campaign Light Water Reactor Accident Tolerant Fuel Performance Metrics

    SciTech Connect (OSTI)

    Brad Merrill; Melissa Teague; Robert Youngblood; Larry Ott; Kevin Robb; Michael Todosow; Chris Stanek; Mitchell Farmer; Michael Billone; Robert Montgomery; Nicholas Brown; Shannon Bragg-Sitton

    2014-02-01

    The safe, reliable and economic operation of the nation’s nuclear power reactor fleet has always been a top priority for the United States’ nuclear industry. As a result, continual improvement of technology, including advanced materials and nuclear fuels, remains central to industry’s success. Decades of research combined with continual operation have produced steady advancements in technology and yielded an extensive base of data, experience, and knowledge on light water reactor (LWR) fuel performance under both normal and accident conditions. In 2011, following the Great East Japan Earthquake, resulting tsunami, and subsequent damage to the Fukushima Daiichi nuclear power plant complex, enhancing the accident tolerance of LWRs became a topic of serious discussion. As a result of direction from the U.S. Congress, the U.S. Department of Energy Office of Nuclear Energy (DOE-NE) initiated an Accident Tolerant Fuel (ATF) Development program. The complex multiphysics behavior of LWR nuclear fuel makes defining specific material or design improvements difficult; as such, establishing qualitative attributes is critical to guide the design and development of fuels and cladding with enhanced accident tolerance. This report summarizes a common set of technical evaluation metrics to aid in the optimization and down selection of candidate designs. As used herein, “metrics” describe a set of technical bases by which multiple concepts can be fairly evaluated against a common baseline and against one another. Furthermore, this report describes a proposed technical evaluation methodology that can be applied to assess the ability of each concept to meet performance and safety goals relative to the current UO2 – zirconium alloy system and relative to one another. The resultant ranked evaluation can then inform concept down-selection, such that the most promising accident tolerant fuel design option(s) can continue to be developed for lead test rod or lead test assembly insertion into a commercial reactor within the desired timeframe (by 2022).

  16. Performance Evaluation of a 4.5 kW (1.3 Refrigeration Tons) Air-Cooled Lithium Bromide/Water Solar Powered (Hot-Water-Fired) Absorption Unit

    SciTech Connect (OSTI)

    Zaltash, Abdolreza; Petrov, Andrei Y; Linkous, Randall Lee; Vineyard, Edward Allan

    2007-01-01

    During the summer months, air-conditioning (cooling) is the single largest use of electricity in both residential and commercial buildings with the major impact on peak electric demand. Improved air-conditioning technology has by far the greatest potential impact on the electric industry compared to any other technology that uses electricity. Thermally activated absorption air-conditioning (absorption chillers) can provide overall peak load reduction and electric grid relief for summer peak demand. This innovative absorption technology is based on integrated rotating heat exchangers to enhance heat and mass transfer resulting in a potential reduction of size, cost, and weight of the "next generation" absorption units. Rotartica Absorption Chiller (RAC) is a 4.5 kW (1.3 refrigeration tons or RT) air-cooled lithium bromide (LiBr)/water unit powered by hot water generated using the solar energy and/or waste heat. Typically LiBr/water absorption chillers are water-cooled units which use a cooling tower to reject heat. Cooling towers require a large amount of space, increase start-up and maintenance costs. However, RAC is an air-cooled absorption chiller (no cooling tower). The purpose of this evaluation is to verify RAC performance by comparing the Coefficient of Performance (COP or ratio of cooling capacity to energy input) and the cooling capacity results with those of the manufacturer. The performance of the RAC was tested at Oak Ridge National Laboratory (ORNL) in a controlled environment at various hot and chilled water flow rates, air handler flow rates, and ambient temperatures. Temperature probes, mass flow meters, rotational speed measuring device, pressure transducers, and a web camera mounted inside the unit were used to monitor the RAC via a web control-based data acquisition system using Automated Logic Controller (ALC). Results showed a COP and cooling capacity of approximately 0.58 and 3.7 kW respectively at 35 C (95 F) design condition for ambient temperature with 40 C (104 F) cooling water temperature. This is in close agreement with the manufacturer data of 0.60 for COP and 3.9 kW for cooling capacity. This study resulted in a complete performance map of RAC which will be used to evaluate the potential benefits of rotating heat exchangers in making the "next-generation" absorption chillers more compact and cost effective without any significant degradation in the performance. In addition, the feasibility of using rotating heat exchangers in other applications will be evaluated.

  17. A model experiment to assess the effects of inclusions on wave propagation in soil media

    SciTech Connect (OSTI)

    Houston, Thomas W; Ray, Richard P

    2009-01-01

    A data acquisition system has been assembled using Micro-Electro-Mechanical Systems (MEMS) technology which provides a flexible data gathering capability to support recording accelerations at various locations within a sand filled 5 meter square test pit that has a depth extending into underlying gravelly soils. Dual-axis accelerometers weighing less than 1 gram each, made possible by advances in MEMS technology, are connected to up to 5 data acquisition (PXI modules) boards, each capable of controlling and recording data from 16 separate dual axis accelerometers. This data acquisition system is used to measure and record acceleration data from wave propagations that are generated by the impact of a hammer on a striker plate and are modified by an inclusion or occlusion buried in the soil media. Thirty-four two-axis accelerometers were placed at surface and embedded locations on either side of various inclusions buried in the test pit. This large number of accelerometers permits experimentally obtaining high quality spatial and temporal data that can describe the character of the generated wave-forms and the modification of those wave-forms caused by the inclusion. A number of differing materials and geometric forms are used to create inclusions in order to provide sufficient data to permit ascertaining the ability of the measurements to describe the character of the inclusion. Continuous Wavelet Transforms are used to remove background noise and to aid interpretation of the character of the generated wave-form.

  18. Noncentrosymmetric salt inclusion oxides: Role of salt lattices and counter ions in bulk polarity

    SciTech Connect (OSTI)

    West, J. Palmer; Hwu, Shiou-Jyh

    2012-11-15

    The synthesis and structural features of a newly emerged class of salt-inclusion solids (SISs) are reviewed. The descriptive chemistry with respect to the role of ionic salt and its correlation with bulk noncentrosymmetricity and polarity of the covalent oxide lattice in question is discussed by means of structure analysis. These unprecedented discoveries have opened doors to novel materials synthesis via the utilities of salt-inclusion chemistry (SIC) that are otherwise known as the molten-salt approach. The result of these investigations prove that the bulk acentricity, or cancellation of which, can be accounted for from the perspective of ionic and/or salt lattices. Highlights: Black-Right-Pointing-Pointer Synthesis and structure of newly emerged salt-inclusion solids are reviewed. Black-Right-Pointing-Pointer Salt lattice and its symmetry correlation with polar framework are discussed. Black-Right-Pointing-Pointer Preservation of acentricity is accounted for from the perspective of ionic and salt lattices.

  19. Inclusive Rates and Spectra of the Lambda, Cascade, and Omega Hyperons

    Office of Scientific and Technical Information (OSTI)

    atBaBar (Thesis/Dissertation) | SciTech Connect Thesis/Dissertation: Inclusive Rates and Spectra of the Lambda, Cascade, and Omega Hyperons atBaBar Citation Details In-Document Search Title: Inclusive Rates and Spectra of the Lambda, Cascade, and Omega Hyperons atBaBar We employ Runs 1-4 off-peak data sample (about 21.5 fb{sup -1}) to produce the current world-best spectra and production rates measurements for three strangely-flavored baryons: the {Lambda} hyperon, the cascade hyperon, and

  20. Hadron mass corrections in semi-inclusive deep-inelastic scattering

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Guerrero Teran, Juan Vicente; Ethier, James J.; Accardi, Alberto; Casper, Steven W.; Melnitchouk, Wally

    2015-09-24

    We found that the spin-dependent cross sections for semi-inclusive lepton-nucleon scattering are derived in the framework of collinear factorization, including the effects of masses of the target and produced hadron at finite Q2. At leading order the cross sections factorize into products of parton distribution and fragmentation functions evaluated in terms of new, mass-dependent scaling variables. Furthermore, the size of the hadron mass corrections is estimated at kinematics relevant for current and future experiments, and the implications for the extraction of parton distributions from semi-inclusive measurements are discussed.

  1. Inclusive electron scattering at high Q/sup 2/ in the region 1 < x < 3

    SciTech Connect (OSTI)

    Day, D.

    1987-01-01

    New inclusive electron scattering data at high Q/sup 2/ from nuclei taken in the x range unavailable to the free nucleon are presented. The ratios of cross section per nucleon, (4/56)d sigma/sup Fe//d sigma/sup He/, show a plateau for 1.3 < x < 2.0 which has been suggested as a signature of quark clusters in nuclei. The subtraction of the quasielastic cross section from the inclusive spectra reveals that the data scale in x at low momentum transfer. A proposal for a new experiment is discussed. 16 refs., 6 figs.

  2. New Pathways and Metrics for Enhanced, Reversible Hydrogen Storage in Boron-Doped Carbon Nanospaces

    SciTech Connect (OSTI)

    Pfeifer, Peter; Wexler, Carlos; Hawthorne, M. Frederick; Lee, Mark W.; Jalistegi, Satish S.

    2014-08-14

    This project, since its start in 2007—entitled “Networks of boron-doped carbon nanopores for low-pressure reversible hydrogen storage” (2007-10) and “New pathways and metrics for enhanced, reversible hydrogen storage in boron-doped carbon nanospaces” (2010-13)—is in support of the DOE's National Hydrogen Storage Project, as part of the DOE Hydrogen and Fuel Cells Program’s comprehensive efforts to enable the widespread commercialization of hydrogen and fuel cell technologies in diverse sectors of the economy. Hydrogen storage is widely recognized as a critical enabling technology for the successful commercialization and market acceptance of hydrogen powered vehicles. Storing sufficient hydrogen on board a wide range of vehicle platforms, at energy densities comparable to gasoline, without compromising passenger or cargo space, remains an outstanding technical challenge. Of the main three thrust areas in 2007—metal hydrides, chemical hydrogen storage, and sorption-based hydrogen storage—sorption-based storage, i.e., storage of molecular hydrogen by adsorption on high-surface-area materials (carbons, metal-organic frameworks, and other porous organic networks), has emerged as the most promising path toward achieving the 2017 DOE storage targets of 0.055 kg H2/kg system (“5.5 wt%”) and 0.040 kg H2/liter system. The objective of the project is to develop high-surface-area carbon materials that are boron-doped by incorporation of boron into the carbon lattice at the outset, i.e., during the synthesis of the material. The rationale for boron-doping is the prediction that boron atoms in carbon will raise the binding energy of hydro- gen from 4-5 kJ/mol on the undoped surface to 10-14 kJ/mol on a doped surface, and accordingly the hydro- gen storage capacity of the material. The mechanism for the increase in binding energy is electron donation from H2 to electron-deficient B atoms, in the form of sp2 boron-carbon bonds. Our team is proud to have demonstrated the predicted increase in binding energy experimentally, currently at ~10 kJ/mol. The synthetic route for incorporation of boron at the outset is to create appropriately designed copoly- mers, with a boron-free and a boron-carrying monomer, followed by pyrolysis of the polymer, yielding a bo- ron-substituted carbon scaffold in which boron atoms are bonded to carbon atoms by synthesis. This is in contrast to a second route (funded by DE-FG36-08GO18142) in which first high-surface area carbon is cre- ated and doped by surface vapor deposition of boron, with incorporation of the boron into the lattice the final step of the fabrication. The challenge in the first route is to create high surface areas without compromising sp2 boron-carbon bonds. The challenge in the second route is to create sp2 boron-carbon bonds without com- promising high surface areas.

  3. Evolution of the Geysers (US) - Data From Fluid-Inclusion Microthermometry and Gas Geochemistry

    SciTech Connect (OSTI)

    Moore, J.N.; Hulen, J.B.; Norman, D.I.

    1995-01-01

    The Geysers, California, is the site of an active hydrothermal system that initially developed between about 1.5 and 2 Ma in response to intrusion of a hypabyssal granitic pluton. Mineralogic and fluid-inclusion data demonstrate that the present vapor-dominated regime evolved from an earlier and more extensive, liquid-dominated hydrothermal system. Circulation of these early fluids produced veins characterized by tourmaline and/or biotite {+-} actinolite {+-} clinopyroxene within the pluton and adjacent biotite-rich hornfels, actinolite {+-} ferroaxinite {+-} epidote, and epidote {+-} chlorite {+-} wairakite within the intermediate parts of the thermal system, and calcite in the outer parts. Potassium feldspar and quartz are present in all assemblages. Maximum pressure-corrected homogenization temperatures and apparent salinities of fluid-inclusions in these veins range from 440 C and 44 weight percent NaCl equivalent within the hornfels (<600 m from the pluton) to 325 C and 5 weight percent NaCl equivalent at approximately 1500 m from the intrusion. We suggest that the shallow, moderate-salinity fluids are crustal waters modified by water-rock interactions and that the high-salinity fluids are magmatic brines. The formation of vapor-dominated conditions is reflected in the abrupt appearance of low salinity (0.0 to 0.4 weight percent NaCl equivalent) fluid inclusions with homogenization temperatures near 265 C. These inclusion fluids are thought to represent steam condensate formed as the liquid-dominated system boiled off.

  4. Development of Metric for Measuring the Impact of RD&D Funding on GTO's Geothermal Exploration Goals (Presentation)

    SciTech Connect (OSTI)

    Jenne, S.; Young, K. R.; Thorsteinsson, H.

    2013-04-01

    The Department of Energy's Geothermal Technologies Office (GTO) provides RD&D funding for geothermal exploration technologies with the goal of lowering the risks and costs of geothermal development and exploration. In 2012, NREL was tasked with developing a metric to measure the impacts of this RD&D funding on the cost and time required for exploration activities. The development of this metric included collecting cost and time data for exploration techniques, creating a baseline suite of exploration techniques to which future exploration and cost and time improvements could be compared, and developing an online tool for graphically showing potential project impacts (all available at http://en.openei.org/wiki/Gateway:Geothermal). The conference paper describes the methodology used to define the baseline exploration suite of techniques (baseline), as well as the approach that was used to create the cost and time data set that populates the baseline. The resulting product, an online tool for measuring impact, and the aggregated cost and time data are available on the Open EI website for public access (http://en.openei.org).

  5. User's Guide to Pre-Processing Data in Universal Translator 2 for the Energy Charting and Metrics Tool (ECAM)

    SciTech Connect (OSTI)

    Taasevigen, Danny J.

    2011-11-30

    This document is a user's guide for the Energy Charting and Metrics Tool to facilitate the examination of energy information from buildings, reducing the time spent analyzing trend and utility meter data. This user guide was generated to help pre-process data with the intention of utilizing the Energy Charting and Metrics (ECAM) tool to improve building operational efficiency. There are numerous occasions when the metered data that is received from the building automation system (BAS) isn't in the right format acceptable for ECAM. This includes, but isn't limited to, cases such as inconsistent time-stamps for the trends (e.g., each trend has its own time-stamp), data with holes (e.g., some time-stamps have data and others are missing data), each point in the BAS is trended and exported into an individual .csv or .txt file, the time-stamp is unrecognizable by ECAM, etc. After reading through this user guide, the user should be able to pre-process all data files and be ready to use this data in ECAM to improve their building operational efficiency.

  6. Knowledge-based prediction of plan quality metrics in intracranial stereotactic radiosurgery

    SciTech Connect (OSTI)

    Shiraishi, Satomi; Moore, Kevin L.; Tan, Jun; Olsen, Lindsey A.

    2015-02-15

    Purpose: The objective of this work was to develop a comprehensive knowledge-based methodology for predicting achievable dose–volume histograms (DVHs) and highly precise DVH-based quality metrics (QMs) in stereotactic radiosurgery/radiotherapy (SRS/SRT) plans. Accurate QM estimation can identify suboptimal treatment plans and provide target optimization objectives to standardize and improve treatment planning. Methods: Correlating observed dose as it relates to the geometric relationship of organs-at-risk (OARs) to planning target volumes (PTVs) yields mathematical models to predict achievable DVHs. In SRS, DVH-based QMs such as brain V{sub 10Gy} (volume receiving 10 Gy or more), gradient measure (GM), and conformity index (CI) are used to evaluate plan quality. This study encompasses 223 linear accelerator-based SRS/SRT treatment plans (SRS plans) using volumetric-modulated arc therapy (VMAT), representing 95% of the institution’s VMAT radiosurgery load from the past four and a half years. Unfiltered models that use all available plans for the model training were built for each category with a stratification scheme based on target and OAR characteristics determined emergently through initial modeling process. Model predictive accuracy is measured by the mean and standard deviation of the difference between clinical and predicted QMs, δQM = QM{sub clin} − QM{sub pred}, and a coefficient of determination, R{sup 2}. For categories with a large number of plans, refined models are constructed by automatic elimination of suspected suboptimal plans from the training set. Using the refined model as a presumed achievable standard, potentially suboptimal plans are identified. Predictions of QM improvement are validated via standardized replanning of 20 suspected suboptimal plans based on dosimetric predictions. The significance of the QM improvement is evaluated using the Wilcoxon signed rank test. Results: The most accurate predictions are obtained when plans are stratified based on proximity to OARs and their PTV volume sizes. Volumes are categorized into small (V{sub PTV} < 2 cm{sup 3}), medium (2 cm{sup 3} < V{sub PTV} < 25 cm{sup 3}), and large (25 cm{sup 3} < V{sub PTV}). The unfiltered models demonstrate the ability to predict GMs to ∼1 mm and fractional brain V{sub 10Gy} to ∼25% for plans with large V{sub PTV} and critical OAR involvements. Increased accuracy and precision of QM predictions are obtained when high quality plans are selected for the model training. For the small and medium V{sub PTV} plans without critical OAR involvement, predictive ability was evaluated using the refined model. For training plans, the model predicted GM to an accuracy of 0.2 ± 0.3 mm and fractional brain V{sub 10Gy} to 0.04 ± 0.12, suggesting highly accurate predictive ability. For excluded plans, the average δGM was 1.1 mm and fractional brain V{sub 10Gy} was 0.20. These δQM are significantly greater than those of the model training plans (p < 0.001). For CI, predictions are close to clinical values and no significant difference was observed between the training and excluded plans (p = 0.19). Twenty outliers with δGM > 1.35 mm were identified as potentially suboptimal, and replanning these cases using predicted target objectives demonstrates significant improvements on QMs: on average, 1.1 mm reduction in GM (p < 0.001) and 23% reduction in brain V{sub 10Gy} (p < 0.001). After replanning, the difference of δGM distribution between the 20 replans and the refined model training plans was marginal. Conclusions: The results demonstrate the ability to predict SRS QMs precisely and to identify suboptimal plans. Furthermore, the knowledge-based DVH predictions were directly used as target optimization objectives and allowed a standardized planning process that bettered the clinically approved plans. Full clinical application of this methodology can improve consistency of SRS plan quality in a wide range of PTV volume and proximity to OARs and facilitate automated treatment planning for this critical treatment site.

  7. A Refractory Inclusion Returned by Stardust from Comet 81P/Wild 2

    SciTech Connect (OSTI)

    Simon, S B; Joswiak, D J; Ishii, H A; Bradley, J P; Chi, M; Grossman, L; Al?on, J; Brownlee, D E; Fallon, S; Hutcheon, I D; Matrajt, G; McKeegan, K D

    2008-05-20

    Among the samples returned from comet 81P/Wild 2 by the Stardust spacecraft is a suite of particles from one impact track (Track 25) that are Ca-, Al-rich and FeO-free. We studied three particles from this track that range in size from 5.3 x 3.2 {micro}m to 15 x 10 {micro}m. Scanning and transmission electron microscopy show that they consist of very fine-grained (from {approx}0.5 to {approx}2 {micro}m) Al-rich, Ti-bearing and Ti-free clinopyroxene, Mg-Al spinel, anorthite, perovskite, and osbornite (TiN). In addition to these phases, the terminal particle, named 'Inti', also contains melilite. All of these phases, with the exception of osbornite, are common in refractory inclusions and are predicted to condense at high temperature from a gas of solar composition. Osbornite, though very rare, has also been found in meteoritic refractory inclusions, and could have formed in a region of the nebula where carbon became enriched relative to oxygen compared to solar composition. Compositions of Ti-pyroxene in Inti are similar, but not identical, to those of fassaite from Allende inclusions. Electron energy loss spectroscopy shows that Ti-rich pyroxene in Inti has Ti{sup 3+}/Ti{sup 4+} within the range of typical meteoritic fassaite, consistent with formation under reducing conditions comparable to those of a system of solar composition. Inti is {sup 16}O-rich, with {delta}{sup 18}O {approx} {delta}{sup 17}O {approx} 40{per_thousand}, like unaltered phases in refractory inclusions and refractory IDPs. With grain sizes, mineralogy, mineral chemistry, and an oxygen isotopic composition like those of refractory inclusions, we conclude that Inti is a refractory inclusion that formed in the inner solar nebula. Identification of a particle that formed in the inner Solar System among the comet samples demonstrates that there was transport of materials from the inner to the outer nebula, probably either in a bipolar outflow or by turbulence.

  8. Double spin asymmetries of inclusive hadron electroproductions from a transversely polarized ³He target

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhao, Yuxiang X.

    2015-07-14

    We report the measurement of beam-target double-spin asymmetries ALT in the inclusive production of identified hadrons, e +³He↑ → h + X, using a longitudinally polarized 5.9 GeV electron beam and a transversely polarized ³He target. Hadrons (π±, K± and proton) were detected at 16° with an average momentum h>=2.35 GeV/c and a transverse momentum (pT) coverage from 0.60 to 0.68 GeV/c. Asymmetries from the ³He target were observed to be non-zero for π± production when the target was polarized transversely in the horizontal plane. The π⁺ and π⁻ asymmetries have opposite signs, analogous to the behavior of ALT inmore » semi-inclusive deep-inelastic scattering.« less

  9. Cupric oxide inclusions in cuprous oxide crystals grown by the floating zone method

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Frazer, Laszlo; Chang, Kelvin B.; Poeppelmeier, Kenneth R.; Ketterson, John B.

    2015-05-08

    Phase-pure cuprous oxide (Cu2O) crystals are difficult to grow since cupric oxide can form within the crystal as the crystal is cooled to ambient conditions. Vacancies are the solute which causes precipitation of macroscopic defects. Therefore, even when a mostly phase-pure single crystal is used as a feed rod, cupric oxide inclusions persist in the recrystallized solid. Control of the thermal profile during crystal growth, however, can improve phase-purity; a slow counter-rotation rate of the feed and seed rods results in fewer inclusions. Cupric oxide can be removed by annealing, which produces a factor of 540 ± 70 increase inmore » phase-purity.« less

  10. A Study of the Optical Properties of Ice Crystals with Black Carbon Inclusions

    SciTech Connect (OSTI)

    Arienti, Marco; Yang, Xiaoyuan; Kopacz, Adrian M; Geier, Manfred

    2015-09-01

    The report focu ses on the modification of the optical properties of ice crystals due to atmospheric black car bon (BC) contamination : the objective is to advance the predictive capabilities of climate models through an improved understanding of the radiative properties of compound particles . The shape of the ice crystal (as commonly found in cirrus clouds and cont rails) , the volume fraction of the BC inclusion , and its location inside the crystal are the three factors examined in this study. In the multiscale description of this problem, where a small absorbing inclusion modifies the optical properties of a much la rger non - absorbing particle, state - of - the - art discretization techniques are combined to provide the best compromise of flexibility and accuracy over a broad range of sizes .

  11. CC-inclusive cross section measured with the T2K near detector

    SciTech Connect (OSTI)

    Weber, Alfons

    2015-05-15

    T2K has performed the first measurement of muon neutrino inclusive charged current interactions on carbon at neutrino energies of ?1 GeV where the measurement is reported as a flux-averaged double differential cross section in muon momentum and angle. The flux is predicted by the beam Monte Carlo and external data, including the results from the NA61/SHINE experiment. The data used for this measurement were taken in 2010 and 2011, with a total of 1.08*10{sup 20} protons-on-target. The analysis is performed on 4485 inclusive charged current interaction candidates selected in the most upstream fine-grained scintillator detector of the near detector. The flux-averaged total cross section is = (6.910.13(stat)0.84(syst)) 10{sup ?39} cm{sup 2}/nucleon for a mean neutrino energy of 0.85 GeV.

  12. Cupric oxide inclusions in cuprous oxide crystals grown by the floating zone method

    SciTech Connect (OSTI)

    Frazer, Laszlo; Chang, Kelvin B.; Poeppelmeier, Kenneth R.; Ketterson, John B.

    2015-05-08

    Phase-pure cuprous oxide (Cu2O) crystals are difficult to grow since cupric oxide can form within the crystal as the crystal is cooled to ambient conditions. Vacancies are the solute which causes precipitation of macroscopic defects. Therefore, even when a mostly phase-pure single crystal is used as a feed rod, cupric oxide inclusions persist in the recrystallized solid. Control of the thermal profile during crystal growth, however, can improve phase-purity; a slow counter-rotation rate of the feed and seed rods results in fewer inclusions. Cupric oxide can be removed by annealing, which produces a factor of 540 ± 70 increase in phase-purity.

  13. Inclusive Production of {rho}{+-}(770) Meson in Hadronic Decays of Z0 Boson

    SciTech Connect (OSTI)

    Beddall, A.; Beddall, A.; Binguel, A.

    2007-04-23

    The inclusive production of the charged vector meson {rho}{+-}(770) in hadronic Z decays is measured with the ALEPH detector at the LEP collider. Decays of {rho}{+-} {yields} {pi}0 + {pi}{+-} are reconstructed for x > 0.05 where x = E{rho}/Ebeam. The results are compared with Monte Carlo model predictions and OPAL measurements. Bose-Einstein effects are found to be important in extracting {rho}{+-}(770) from two pion invariant mass spectra.

  14. Measurements of transverse momentum in semi-inclusive deep-inelastic scattering at CLAS

    SciTech Connect (OSTI)

    K.A. Griffioen

    2012-12-01

    With mounting experimental evidence that only a small fraction of the proton's spin comes from the spins of its quarks and gluons, the quest for orbital angular momentum has begun. The parton distributions relevant to this depend on transverse quark momenta. Recent CLAS semi-inclusive deep-inelastic scattering measurements probe these new transverse-momentum-dependent parton distributions using longitudinally polarized beams and targets and detecting {pi}{sup +},{pi}{sup -} and {pi}{sup 0} in the final state.

  15. On use of CO{sub 2} chemiluminescence for combustion metrics in natural gas fired reciprocating engines.

    SciTech Connect (OSTI)

    Gupta, S. B.; Bihari, B.; Biruduganti, M.; Sekar, R.; Zigan, J.

    2011-01-01

    Flame chemiluminescence is widely acknowledged to be an indicator of heat release rate in premixed turbulent flames that are representative of gas turbine combustion. Though heat release rate is an important metric for evaluating combustion strategies in reciprocating engine systems, its correlation with flame chemiluminescence is not well studied. To address this gap an experimental study was carried out in a single-cylinder natural gas fired reciprocating engine that could simulate turbocharged conditions with exhaust gas recirculation. Crank angle resolved spectra (266-795 nm) of flame luminosity were measured for various operational conditions by varying the ignition timing for MBT conditions and by holding the speed at 1800 rpm and Brake Mean effective Pressure (BMEP) at 12 bar. The effect of dilution on CO*{sub 2}chemiluminescence intensities was studied, by varying the global equivalence ratio (0.6-1.0) and by varying the exhaust gas recirculation rate. It was attempted to relate the measured chemiluminescence intensities to thermodynamic metrics of importance to engine research -- in-cylinder bulk gas temperature and heat release rate (HRR) calculated from measured cylinder pressure signals. The peak of the measured CO*{sub 2} chemiluminescence intensities coincided with peak pressures within {+-}2 CAD for all test conditions. For each combustion cycle, the peaks of heat release rate, spectral intensity and temperature occurred in that sequence, well separated temporally. The peak heat release rates preceded the peak chemiluminescent emissions by 3.8-9.5 CAD, whereas the peak temperatures trailed by 5.8-15.6 CAD. Such a temporal separation precludes correlations on a crank-angle resolved basis. However, the peak cycle heat release rates and to a lesser extent the peak cycle temperatures correlated well with the chemiluminescent emission from CO*{sub 2}. Such observations point towards the potential use of flame chemiluminescence to monitor peak bulk gas temperatures as well as peak heat release rates in natural gas fired reciprocating engines.

  16. FRACTIONAL CRYSTALLIZATION LABORATORY TESTING FOR INCLUSION & COPRECIPITATION WITH ACTUAL TANK WASTE

    SciTech Connect (OSTI)

    WARRANT, R.W.

    2006-12-11

    Fractional crystallization is being considered as a pretreatment method to support supplemental treatment of retrieved single-shell tank (SST) saltcake waste at the Hanford Site. The goal of the fractional crystallization process is to optimize the separation of the radioactivity (radionuclides) from the saltcake waste and send it to the Waste Treatment and Immobilization Plant and send the bulk of the saltcake to the supplemental treatment plant (bulk vitrification). The primary factors that influence the separation efficiency are (1) solid/liquid separation efficiency, (2) contaminant inclusions, and (3) co-precipitation. This is a report of testing for factors (2) and (3) with actual tank waste samples. For the purposes of this report, contaminant inclusions are defined as the inclusion of supernatant, containing contaminating radionuclides, in a pocket within the precipitating saltcake crystals. Co-precipitation is defined as the simultaneous precipitation of a saltcake crystal with a contaminating radionuclide. These two factors were tested for various potential fractional crystallization product salts by spiking the composite tank waste samples (SST Early or SST Late, external letter CH2M-0600248, ''Preparation of Composite Tank Waste Samples for ME-21 Project'') with the desired target salt and then evaporating to precipitate that salt. SST Early represents the typical composition of dissolved saltcake early in the retrieval process, and SST Late represents the typical composition during the later stages of retrieval.

  17. Chemical Signatures of and Precursors to Fractures Using Fluid Inclusion Stratigraphy

    SciTech Connect (OSTI)

    Lorie M. Dilley

    2011-03-30

    Enhanced Geothermal Systems (EGS) are designed to recover heat from the subsurface by mechanically creating fractures in subsurface rocks. Open or recently closed fractures would be more susceptible to enhancing the permeability of the system. Identifying dense fracture areas as well as large open fractures from small fracture systems will assist in fracture stimulation site selection. Geothermal systems are constantly generating fractures (Moore, Morrow et al. 1987), and fluids and gases passing through rocks in these systems leave small fluid and gas samples trapped in healed microfractures. These fluid inclusions are faithful records of pore fluid chemistry. Fluid inclusions trapped in minerals as the fractures heal are characteristic of the fluids that formed them, and this signature can be seen in fluid inclusion gas analysis. This report presents the results of the project to determine fracture locations by the chemical signatures from gas analysis of fluid inclusions. With this project we hope to test our assumptions that gas chemistry can distinguish if the fractures are open and bearing production fluids or represent prior active fractures and whether there are chemical signs of open fracture systems in the wall rock above the fracture. Fluid Inclusion Stratigraphy (FIS) is a method developed for the geothermal industry which applies the mass quantification of fluid inclusion gas data from drill cuttings and applying known gas ratios and compositions to determine depth profiles of fluid barriers in a modern geothermal system (Dilley, 2009; Dilley et al., 2005; Norman et al., 2005). Identifying key gas signatures associated with fractures for isolating geothermal fluid production is the latest advancement in the application of FIS to geothermal systems (Dilley and Norman, 2005; Dilley and Norman, 2007). Our hypothesis is that peaks in FIS data are related to location of fractures. Previous work (DOE Grant DE-FG36-06GO16057) has indicated differences in the chemical signature of fluid inclusions between open and closed fractures as well as differences in the chemical signature of open fractures between geothermal systems. Our hypothesis is that open fracture systems can be identified by their FIS chemical signature; that there are differences based on the mineral assemblages and geology of the system; and that there are chemical precursors in the wall rock above open, large fractures. Specific goals for this project are: (1) To build on the preliminary results which indicate that there are differences in the FIS signatures between open and closed fractures by identifying which chemical species indicate open fractures in both active geothermal systems and in hot, dry rock; (2) To evaluate the FIS signatures based on the geology of the fields; (3) To evaluate the FIS signatures based on the mineral assemblages in the fracture; and (4) To determine if there are specific chemical signatures in the wall rock above open, large fractures. This method promises to lower the cost of geothermal energy production in several ways. Knowledge of productive fractures in the boreholes will allow engineers to optimize well production. This information can aid in well testing decisions, well completion strategies, and in resource calculations. It will assist in determining the areas for future fracture enhancement. This will develop into one of the techniques in the 'tool bag' for creating and managing Enhanced Geothermal Systems.

  18. DOE JGI Quality Metrics; Approaches to Scaling and Improving Metagenome Assembly (Metagenomics Informatics Challenges Workshop: 10K Genomes at a Time)

    ScienceCinema (OSTI)

    Copeland, Alex [DOE JGI]; Brown, C Titus [Michigan State University

    2013-01-22

    DOE JGI's Alex Copeland on "DOE JGI Quality Metrics" and Michigan State University's C. Titus Brown on "Approaches to Scaling and Improving Metagenome Assembly" at the Metagenomics Informatics Challenges Workshop held at the DOE JGI on October 12-13, 2011.

  19. On the role of the Sivers effect in A{sub N} for inclusive particle production in pp collisions

    SciTech Connect (OSTI)

    Anselmino, Mauro; Boglione, Mariaelena; D'Alesio, Umberto; Melis, Stefano; Murgia, Francesco; Prokudin, Alexei

    2014-01-01

    Single spin asymmetries, A{sub N} , for inclusive particle production in pp collisions are considered within a generalized parton model with inclusion of spin and tranverse momentum effects. We consider the potential role of the Sivers effect in A{sub N} , as extracted from a careful analysis of azimuthal asymmetries in SIDIS, and discuss its phenomenological consequences in connection with a recently updated study of the Collins effect.

  20. Short Narrative About Promising Practices The National Nuclear Security Administration's (NNSA) Diversity and Inclusion Implementation Plan was

    National Nuclear Security Administration (NNSA)

    2 Short Narrative About Promising Practices The National Nuclear Security Administration's (NNSA) Diversity and Inclusion Implementation Plan was approved and submitted to the Department on April 13, 2013. NNSA's Office of Human Capital Management participated on a regular basis with the Department of Energy's (DOE) Diversity and Inclusion (D&I) Council in FY 2013. NNSA continues to establish a partnership with the DOE Office of Diversity Programs (ODP) to share information, collaborate and

  1. SU-E-T-379: Concave Approximations of Target Volume Dose Metrics for Intensity- Modulated Radiotherapy Treatment Planning

    SciTech Connect (OSTI)

    Xie, Y; Chen, Y; Wickerhauser, M; Deasy, J

    2014-06-01

    Purpose: The widely used treatment plan metric Dx (mimimum dose to the hottest x% by volume of the target volume) is simple to interpret and use, but is computationally poorly behaved (non-convex), this impedes its use in computationally efficient intensity-modulated radiotherapy (IMRT) treatment planning algorithms. We therefore searched for surrogate metrics that are concave, computationally efficient, and accurately correlated to Dx values in IMRT treatment plans. Methods: To find concave surrogates of D95and more generally, Dx values with variable x valueswe tested equations containing one or two generalized equivalent uniform dose (gEUD) functions. Fits were obtained by varying gEUD a parameter values, as well as the linear equation coefficients. Fitting was performed using a dataset of dose-volume histograms from 498 de-identified head and neck IMRT treatment plans. Fit characteristics were tested using a crossvalidation process. Reported root-mean-square error values were averaged over the cross-validation shuffles. Results: As expected, the two-gEUD formula provided a superior fit, compared to the single-gEUD formula. The best approximation uses two gEUD terms: 16.25 x gEUD[a=0.45] 15.30 x gEUD[a=1.75] 0.69. The average root-mean-square error on repeated (70/30) cross validation was 0.94 Gy. In addition, a formula was found that reasonably approximates Dx for x between 80% and 96%. Conclusion: A simple concave function using two gEUD terms was found that correlates well with PTV D95s for these head and neck treatment plans. More generally, a formula was found that represents well the Dx for x values from 80% to 96%, thus providing a computationally efficient formula for use in treatment planning optimization. The formula may need to be adjusted for other institutions with different treatment planning protocols. We conclude that the strategy of replacing Dx values with gEUD-based formulas is promising.

  2. Partonic Transverse Motion in Unpolarized Semi-Inclusive Deep Inelastic Scattering Processes

    SciTech Connect (OSTI)

    M. Boglione, S. Melis, A. Prokudin

    2011-08-01

    We analyse the role of partonic transverse motion in unpolarized Semi-Inclusive Deep Inelastic Scattering (SIDIS) processes. Imposing appropriate kinematical conditions, we find some constraints which fix an upper limit to the range of allowed k_perp values. We show that, applying these additional requirements on the partonic kinematics, we obtain different results with respect to the usual phenomenological approach based on the Gaussian smearing with analytical integration over an unlimited range of k_perp values. These variations are particularly interesting for some observables, like the < cos phi_h > azimuthal modulation of the unpolarized SIDIS cross section or the average transverse momentum of the final, detected hadron.

  3. Measurement of the inclusive B sup * cross section above the. Upsilon. (4 S )

    SciTech Connect (OSTI)

    Akerib, D.S.; Barish, B.; Cowen, D.F.; Eigen, G.; Stroynowski, R.; Urheim, J.; Weinstein, A.J.; Morrison, R.; Schmidt, D.; Procario, M.; Johnson, D.R.; Lingel, K.; Rankin, P.; Smith, J.G.; Alexander, J.; Bebek, C.; Berkelman, K.; Besson, D.; Browder, T.E.; Cassel, D.G.; Cheu, E.; Coffman, D.M.; Drell, P.S.; Ehrlich, R.; Galik, R.S.; Garcia-Sciveres, M.; Geiser, B.; Gittelman, B.; Gray, S.W.; Hartill, D.L.; Heltsley, B.K.; Honscheid, K.; Kandaswamy, J.; Katayama, N.; Kreinick, D.L.; Lewis, J.D.; Ludwig, G.S.; Masui, J.; Mevissen, J.; Mistry, N.B.; Nandi, S.; Ng, C.R.; Nordberg, E.; O'Grady, C.; Patterson, J.R.; Peterson, D.; Pisharody, M.; Riley, D.; Sapper, M.; Selen, M.; Worden, H.; Worris, M.; Avery, P.; Freyberger, A.; Rodriguez, J.; Yelton, J.; Kinoshita, K.; Pipkin, F.; Wilson, R.; Wolinski, J.; Xiao, D.; Sadoff, A.J.; Ammar, R.; Baringer, P.; Coppage, D.; Davis, R.; Haas, P.; Kelly, M.; Kwak, N.; Lam, H.; Ro, S.; Kubota, Y.; Nelson, J.K.; Perticone, D.; Poling, R.; Schrenk, S.; A

    1991-09-23

    Using the CLEO II detector at the Cornell Electron Storage Ring, we have determined the inclusive {ital B}{sup *} cross section above the {Upsilon}(4{ital S}) resonance in the energy range from 10.61 to 10.70 GeV. We also report a new measurement of the energy of the {ital B}{sup *}{r arrow}{ital B}{gamma} transition photon of 46.2{plus minus}0.3{plus minus}0.8 MeV.

  4. Black Warrior: Sub-soil gas and fluid inclusion exploration and slim well drilling

    Broader source: Energy.gov [DOE]

    DOE Geothermal Peer Review 2010 - Presentation. Project Objectives: Discover a blind, low-moderate temperature resource: Apply a combination of detailed sub-soil gas, hydrocarbon, and isotope data to define possible upflow areas; Calibrate the sub-soil chemistry with down-hole fluid inclusion stratigraphy and fluid analyses to define a follow-up exploration drilling target; Create short term jobs and long term employment through resource exploration, development and power plant operation; Extend and adapt the DOE sub-soil 2 meter probe technology to gas sampling.

  5. Precise Measurements of Beam Spin Asymmetries in Semi-Inclusive π0 production

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aghasyan, M.; Avakian, H.; Rossi, P.; De Sanctis, E.; Hasch, D.; Mirazita, M.; Adikaram, D.; Amaryan, M. J.; Anghinolfi, M.; Baghdasaryan, H.; et al

    2011-10-01

    We present studies of single-spin asymmetries for neutral pion electroproduction in semi-inclusive deep-inelastic scattering of 5.776 GeV polarized electrons from an unpolarized hydrogen target, using the CEBAF Large Acceptance Spectrometer (CLAS) at the Thomas Jefferson National Accelerator Facility. A substantial sin Φh amplitude has been measured in the distribution of the cross section asymmetry as a function of the azimuthal angle Φh of the produced neutral pion. The dependence of this amplitude on Bjorken x and on the pion transverse momentum is extracted with significantly higher precision than previous data and is compared to model calculations.

  6. AN in inclusive lepton-proton collisions: TMD and twist-3 approaches

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Prokudin, Alexei

    2015-01-23

    We consider the inclusive production of hadrons in lepton-nucleon scattering. For a transversely polarized nucleon this reaction shows a left-right azimuthal asymmetry, which we compute this asymmetry in both TMD and in twist-3 collinear factorization formalisms. All non-perturbative parton correlators of the calculation are fixed through information from other hard processes. Our results for the left-right asymmetry agree in sign with recent data for charged pion production from the HERMES Collaboration and from Jefferson Lab. As a result, we discuss similarities and differences of two formalisms.

  7. How Does Your Data Center Measure Up? Energy Efficiency Metrics and Benchmarks for Data Center Infrastructure Systems

    SciTech Connect (OSTI)

    Mathew, Paul; Greenberg, Steve; Ganguly, Srirupa; Sartor, Dale; Tschudi, William

    2009-04-01

    Data centers are among the most energy intensive types of facilities, and they are growing dramatically in terms of size and intensity [EPA 2007]. As a result, in the last few years there has been increasing interest from stakeholders - ranging from data center managers to policy makers - to improve the energy efficiency of data centers, and there are several industry and government organizations that have developed tools, guidelines, and training programs. There are many opportunities to reduce energy use in data centers and benchmarking studies reveal a wide range of efficiency practices. Data center operators may not be aware of how efficient their facility may be relative to their peers, even for the same levels of service. Benchmarking is an effective way to compare one facility to another, and also to track the performance of a given facility over time. Toward that end, this article presents the key metrics that facility managers can use to assess, track, and manage the efficiency of the infrastructure systems in data centers, and thereby identify potential efficiency actions. Most of the benchmarking data presented in this article are drawn from the data center benchmarking database at Lawrence Berkeley National Laboratory (LBNL). The database was developed from studies commissioned by the California Energy Commission, Pacific Gas and Electric Co., the U.S. Department of Energy and the New York State Energy Research and Development Authority.

  8. Comparative hazard analysis and toxicological modeling of diverse nanomaterials using the embryonic zebrafish (EZ) metric of toxicity

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Harper, Bryan; Thomas, Dennis G.; Chikkagoudar, Satish; Baker, Nathan A.; Tang, Kaizhi; Heredia-Langner, Alejandro; Lins, Roberto D.; Harper, Stacey

    2015-06-04

    The integration of rapid assays, large data sets, informatics and modeling can overcome current barriers in understanding nanomaterial structure-toxicity relationships by providing a weight-of-the-evidence mechanism to generate hazard rankings for nanomaterials. Here we present the use of a rapid, low-cost assay to perform screening-level toxicity evaluations of nanomaterials in vivo. Calculated EZ Metric scores, a combined measure of morbidity and mortality, were established at realistic exposure levels and used to develop a predictive model of nanomaterial toxicity. Hazard ranking and clustering analysis of 68 diverse nanomaterials revealed distinct patterns of toxicity related to both core composition and outermost surface chemistrymore » of nanomaterials. The resulting clusters guided the development of a predictive model of gold nanoparticle toxicity to embryonic zebrafish. In addition, our findings suggest that risk assessments based on the size and core composition of nanomaterials alone may be wholly inappropriate, especially when considering complex engineered nanomaterials. These findings reveal the need to expeditiously increase the availability of quantitative measures of nanomaterial hazard and broaden the sharing of that data and knowledge to support predictive modeling. In addition, research should continue to focus on methodologies for developing predictive models of nanomaterial hazard based on sub-lethal responses to low dose exposures.« less

  9. Comparative hazard analysis and toxicological modeling of diverse nanomaterials using the embryonic zebrafish (EZ) metric of toxicity

    SciTech Connect (OSTI)

    Harper, Bryan; Thomas, Dennis G.; Chikkagoudar, Satish; Baker, Nathan A.; Tang, Kaizhi; Heredia-Langner, Alejandro; Lins, Roberto D.; Harper, Stacey

    2015-06-04

    The integration of rapid assays, large data sets, informatics and modeling can overcome current barriers in understanding nanomaterial structure-toxicity relationships by providing a weight-of-the-evidence mechanism to generate hazard rankings for nanomaterials. Here we present the use of a rapid, low-cost assay to perform screening-level toxicity evaluations of nanomaterials in vivo. Calculated EZ Metric scores, a combined measure of morbidity and mortality, were established at realistic exposure levels and used to develop a predictive model of nanomaterial toxicity. Hazard ranking and clustering analysis of 68 diverse nanomaterials revealed distinct patterns of toxicity related to both core composition and outermost surface chemistry of nanomaterials. The resulting clusters guided the development of a predictive model of gold nanoparticle toxicity to embryonic zebrafish. In addition, our findings suggest that risk assessments based on the size and core composition of nanomaterials alone may be wholly inappropriate, especially when considering complex engineered nanomaterials. These findings reveal the need to expeditiously increase the availability of quantitative measures of nanomaterial hazard and broaden the sharing of that data and knowledge to support predictive modeling. In addition, research should continue to focus on methodologies for developing predictive models of nanomaterial hazard based on sub-lethal responses to low dose exposures.

  10. Investigation of platinum alloys for melting of inclusion free laser glass: Final report

    SciTech Connect (OSTI)

    Izumitani, T.; Toratani, H.; Meissner, H.E.

    1986-02-28

    The objective of this work is to evaluate the suitability of Pt alloys as crucible materials for melting LHG-8 phosphate laser glass. The tendency of forming metallic inclusions and ionic dissolution of alloy components in the glass is to be compared with that of pure Pt. Ionic Pt is introduced into the glass melt by direct dissolution of Pt at the crucible-melt interface and by vapor phase transport. It was felt that a Pt-alloy may behave sufficiently differently from Pt that a number of alloys should be studied. Pt inclusions may originate from Pt which reprecipitates from the glass melt on cooling or change in redox-conditions; from volatilized Pt which deposits in colder zones of the melting environment as crystallites which may drop back into the glass melt; and/or from Pt particles which are mechanically removed from the crucible and drop into the glass melt. Besides pure Pt, the following alloys have been tested: Pt//sup 10/Ir, Pt//sup 10/Rh, Pt//sup 5/Au, Pt-ZGS, Pt//sup 5/Au-ZGS, Pt//sup 10/Rh-ZGS.

  11. Final-state interactions in inclusive deep-inelastic scattering from the deuteron

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Cosyn, Wim; Melnitchouk, Wally; Sargsian, Misak M.

    2014-01-16

    We explore the role of final-state interactions (FSI) in inclusive deep-inelastic scattering from the deuteron. Relating the inclusive cross section to the deuteron forward virtual Compton scattering amplitude, a general formula for the FSI contribution is derived in the generalized eikonal approximation, utilizing the diffractive nature of the effective hadron-nucleon interaction. The calculation uses a factorized model with a basis of three resonances with mass W~<2 GeV and a continuum contribution for larger W as the relevant set of effective hadron states entering the final-state interaction amplitude. The results show sizeable on-shell FSI contributions for Bjorken x ~> 0.6 andmore » Q2 < 10 GeV2 increasing in magnitude for lower Q2, but vanishing in the high-Q2 limit due to phase space constraints. The off-shell rescattering contributes at x ~> 0.8 and is taken as an uncertainty on the on-shell result.« less

  12. Influence of germanium nano-inclusions on the thermoelectric power factor of bulk bismuth telluride alloy

    SciTech Connect (OSTI)

    Satyala, Nikhil; Zamanipour, Zahra; Norouzzadeh, Payam; Krasinski, Jerzy S.; Vashaee, Daryoosh; Tahmasbi Rad, Armin; Tayebi, Lobat

    2014-05-28

    Nanocomposite thermoelectric compound of bismuth telluride (Bi{sub 2}Te{sub 3}) with 5 at. % germanium nano-inclusions was prepared via mechanically alloying and sintering techniques. The influence of Ge nano-inclusions and long duration annealing on the thermoelectric properties of nanostructured Bi{sub 2}Te{sub 3} were investigated. It was found that annealing has significant effect on the carrier concentration, Seebeck coefficient, and the power factor of the thermoelectric compound. The systematic heat treatment also reduced the density of donor type defects thereby decreasing the electron concentration. While the as-pressed nanocomposite materials showed n-type properties, it was observed that with the increase of annealing time, the nanocomposite gradually transformed to an abundantly hole-dominated (p-type) sample. The long duration annealing (∼500 h) resulted in a significantly enhanced electrical conductivity pertaining to the augmentation in the density and the structural properties of the sample. Therefore, a simultaneous enhancement in both electrical and Seebeck coefficient characteristics resulted in a remarkable increase in the thermoelectric power factor.

  13. Double spin asymmetries of inclusive hadron electroproductions from a transversely polarized ³He target

    SciTech Connect (OSTI)

    Zhao, Yuxiang X.

    2015-07-14

    We report the measurement of beam-target double-spin asymmetries ALT in the inclusive production of identified hadrons, e +³He → h + X, using a longitudinally polarized 5.9 GeV electron beam and a transversely polarized ³He target. Hadrons (π±, K± and proton) were detected at 16° with an average momentum h>=2.35 GeV/c and a transverse momentum (pT) coverage from 0.60 to 0.68 GeV/c. Asymmetries from the ³He target were observed to be non-zero for π± production when the target was polarized transversely in the horizontal plane. The π⁺ and π⁻ asymmetries have opposite signs, analogous to the behavior of ALT in semi-inclusive deep-inelastic scattering.

  14. Inclusive b-jet production in pp collisions at sqrt(s)=7 TeV

    SciTech Connect (OSTI)

    Chatrchyan, Serguei; et al.

    2012-04-01

    The inclusive b-jet production cross section in pp collisions at a center-of-mass energy of 7 TeV is measured using data collected by the CMS experiment at the LHC. The cross section is presented as a function of the jet transverse momentum in the range 18 < pT < 200 GeV for several rapidity intervals. The results are also given as the ratio of the b-jet production cross section to the inclusive jet production cross section. The measurement is performed with two different analyses, which differ in their trigger selection and b-jet identification: a jet analysis that selects events with a b jet using a sample corresponding to an integrated luminosity of 34 inverse picobarns, and a muon analysis requiring a b jet with a muon based on an integrated luminosity of 3 inverse picobarns. In both approaches the b jets are identified by requiring a secondary vertex. The results from the two methods are in agreement with each other and with next-to-leading order calculations, as well as with predictions based on the PYTHIA event generator.

  15. Microsoft Word - Summary.doc

    National Nuclear Security Administration (NNSA)

    ... of the NTS Air Quality Operating Permit, which was issued by the Nevada Bureau of Air Pollution Control in June 2004. During that year, an estimated 3.32 metric tons (3.66 tons) ...

  16. EIS-0283-S2: Final Supplemental Environmental Impact Statement...

    Broader source: Energy.gov (indexed) [DOE]

    Statement This Final SEIS evaluates the potential environmental impacts of alternatives for disposition of 13.1 metric tons (14.4 tons) of surplus plutonium for which a disposition...

  17. Sandia National Laboratories: Z Pulsed Power Facility: How Does...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lines. Connected to the vacuum side of the electrode rings of the interface are five nesting stainless-steel cones (total weight about 10 tons (9 metric tons)) that are...

  18. ARM - 2007 Performance Metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 (CAM3). Document and evaluate ice water content simulated by CAM3 using ARM and NASA Aura satellite data. Product DocumentationDeliverables - The implementation of the cloud...

  19. Fire Protection Program Metrics

    Broader source: Energy.gov [DOE]

    Presenter: Perry E. D ’Antonio, P.E., Acting Sr. Manager, Fire Protection - Sandia National Laboratories

  20. Oil Security Metrics Model

    SciTech Connect (OSTI)

    Greene, David L.; Leiby, Paul N.

    2005-03-06

    A presentation to the IWG GPRA USDOE, March 6, 2005, Washington, DC. OSMM estimates oil security benefits of changes in the U.S. oil market.

  1. FY 2015 METRIC SUMMARY

    Broader source: Energy.gov [DOE]

    The Root Cause Analysis report identifies the key elements necessary to make the meaningful changes required to consistently deliver projects within cost and schedule performance parameters.

  2. NIF Target Shot Metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Exp Cap - Experimental Capability Natl Sec Appl - National Security Applications DS - Discovery Science ICF - Inertial Confinement Fusion HED - High Energy Density For internal ...

  3. ASR - 2011 Performance Metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    climate modeling within BER CESD. The goal of the climate modeling program is the development of climate models that include natural and human systems, which will project...

  4. Recent Results of Semi-inclusive DIS Experiments at Jefferson Lab

    SciTech Connect (OSTI)

    Allada, Kalyan

    2015-09-01

    Semi-inclusive deep inelastic scattering (SIDIS) is a powerful tool to explore the 3-d structure of nucleon in momentum space. Through a combination of polarized or unpolarized lepton beam and nucleon target one can study various transverse-momentum dependent parton distribution functions (TMDs) that appear in the SIDIS cross-section. TMDs provide a description of nucleon structure in terms of parton’s transverse momentum and its transverse spin, which enables us to study the quark orbital angular momentum effects in the nucleon. Several SIDIS experiments were performed in three experimental halls at JLab with 6 GeV electron beam using both polarized or upolarized beam and target combinations. The kinematic range was mainly focued on valence quark region. In this proceeding we will discuss some of the recent results from JLab 6 GeV run.

  5. Inclusive J/{psi} Production in {Upsilon} Decay Via Color-Singlet Mechanism

    SciTech Connect (OSTI)

    He Zhiguo; Wang Jianxiong

    2011-05-23

    We report the recent works about the inclusive J/{psi} production in {Upsilon} decay. Our results show that until now the color-singlet (CS) contribution which includes leading order ({alpha}{sub s}{sup 5}){Upsilon}{yields}J/{psi}+cc-barg process and {alpha}{sub s}{sup 6} order {Upsilon}{yields}J/{psi}+gg(4g) process as well as {alpha}{sub s}{sup 2{alpha}2} order {Upsilon}{yields}J/{psi}+cc-bar and {Upsilon}{yields}J/{psi}+gg processes can not explain the experimental data yet. A preliminary CS prediction of R{sub cc} (B({Upsilon}{yields}J/{psi}+cc-bar+X)/B({Upsilon}{yields}J/{psi}+X)) 0.39{sub -0.20}{sup +0.21}, which is much larger than color-octet (CO) prediction, is also given as a good quantity to discriminate the CS and color-octet mechanism.

  6. Exclusive and inclusive decays of B mesons into D sub s mesons

    SciTech Connect (OSTI)

    Bortoletto, D.; Goldberg, M.; Horwitz, N.; Jain, V.; Mestayer, M.D.; Moneti, G.C.; Sharma, V.; Shipsey, I.P.J.; Skwarnicki, T.; Thulasidas, M.; Csorna, S.E.; Letson, T.; Alexander, J.; Artuso, M.; Bebek, C.; Berkelman, K.; Cassel, D.G.; Cheu, E.; Coffman, D.M.; Crawford, G.; DeWire, J.W.; Drell, P.S.; Ehrlich, R.; Galik, R.S.; Gittelman, B.; Gray, S.W.; Halling, A.M.; Hartill, D.L.; Heltsley, B.K.; Kandaswamy, J.; Katayama, N.; Kreinick, D.L.; Lewis, J.D.; Mistry, N.B.; Mueller, J.; Namjoshi, R.; Nandi, S.; Nordberg, E.; O'Grady, C.; Peterson, D.; Pisharody, M.; Riley, D.; Sapper, M.; Silverman, A.; Stone, S.; Worden, H.; Worris, M.; Sadoff, A.J.; Avery, P.; Besson, D.; Garren, L.; Yelton, J.; Bowcock, T.; Kinoshita, K.; Pipkin, F.M.; Procario, M.; Wilson, R.; Wolinski, J.; Xiao, D.; Ammar, R.; Baringer, P.; Coppage, D.; Haas, P.; Lam, H.; Jawahery, A.; Park, C.H.; Kubota, Y.; Nelson, J.K.; Perticone, D.; Poling, R.; Fulton, R.; Hempstead, M.; Jensen, T.; Johnson, D.R.; Kagan, H.; Kass

    1990-04-30

    We have studied the production of {ital D}{sub {ital s}} mesons in the decays of {ital B} mesons at the {Upsilon}(4{ital S}) resonance. We report on the first observation of exclusive {ital B}-meson decays {ital B}{r arrow}{ital D}{sub {ital s}}{sup {minus}}{ital D*}{sup +}, {ital B}{r arrow}{ital D}{sub {ital s}}{sup {minus}}{ital D}{sup +}, and {ital B}{r arrow}{ital D}{sub {ital s}}{sup {minus}}{ital D}{sup 0}. We also present a new measurement of the branching ratio and the momentum spectrum for the inclusive decay {ital B}{r arrow}{ital D}{sub {ital s}X}.

  7. Inclusion free cadmium zinc tellurium and cadmium tellurium crystals and associated growth method

    DOE Patents [OSTI]

    Bolotnikov, Aleskey E.; James, Ralph B.

    2010-07-20

    The present disclosure provides systems and methods for crystal growth of cadmium zinc tellurium (CZT) and cadmium tellurium (CdTe) crystals with an inverted growth reactor chamber. The inverted growth reactor chamber enables growth of single, large, high purity CZT and CdTe crystals that can be used, for example, in X-ray and gamma detection, substrates for infrared detectors, or the like. The inverted growth reactor chamber enables reductions in the presence of Te inclusions, which are recognized as an important limiting factor in using CZT or CdTe as radiation detectors. The inverted growth reactor chamber can be utilized with existing crystal growth techniques such as the Bridgman crystal growth mechanism and the like. In an exemplary embodiment, the inverted growth reactor chamber is a U-shaped ampoule.

  8. EIS-0283: Amended Record of Decision | Department of Energy

    Office of Environmental Management (EM)

    of Energy Draft Supplemental Environmental Impact Statement EIS-0283-S2: Draft Supplemental Environmental Impact Statement Surplus Plutonium Disposition This Draft SEIS evaluates the potential environmental impacts of alternatives for disposition of 13.1 metric tons (14.4 tons) of surplus plutonium for which DOE has not made a disposition decision, including 7.1 metric tons (7.8 tons) of plutonium from pits that were declared excess to national defense needs after publication of the 2007

  9. Evaluating IMRT and VMAT dose accuracy: Practical examples of failure to detect systematic errors when applying a commonly used metric and action levels

    SciTech Connect (OSTI)

    Nelms, Benjamin E.; Chan, Maria F.; Jarry, Genevive; Lemire, Matthieu; Lowden, John; Hampton, Carnell

    2013-11-15

    Purpose: This study (1) examines a variety of real-world cases where systematic errors were not detected by widely accepted methods for IMRT/VMAT dosimetric accuracy evaluation, and (2) drills-down to identify failure modes and their corresponding means for detection, diagnosis, and mitigation. The primary goal of detailing these case studies is to explore different, more sensitive methods and metrics that could be used more effectively for evaluating accuracy of dose algorithms, delivery systems, and QA devices.Methods: The authors present seven real-world case studies representing a variety of combinations of the treatment planning system (TPS), linac, delivery modality, and systematic error type. These case studies are typical to what might be used as part of an IMRT or VMAT commissioning test suite, varying in complexity. Each case study is analyzed according to TG-119 instructions for gamma passing rates and action levels for per-beam and/or composite plan dosimetric QA. Then, each case study is analyzed in-depth with advanced diagnostic methods (dose profile examination, EPID-based measurements, dose difference pattern analysis, 3D measurement-guided dose reconstruction, and dose grid inspection) and more sensitive metrics (2% local normalization/2 mm DTA and estimated DVH comparisons).Results: For these case studies, the conventional 3%/3 mm gamma passing rates exceeded 99% for IMRT per-beam analyses and ranged from 93.9% to 100% for composite plan dose analysis, well above the TG-119 action levels of 90% and 88%, respectively. However, all cases had systematic errors that were detected only by using advanced diagnostic techniques and more sensitive metrics. The systematic errors caused variable but noteworthy impact, including estimated target dose coverage loss of up to 5.5% and local dose deviations up to 31.5%. Types of errors included TPS model settings, algorithm limitations, and modeling and alignment of QA phantoms in the TPS. Most of the errors were correctable after detection and diagnosis, and the uncorrectable errors provided useful information about system limitations, which is another key element of system commissioning.Conclusions: Many forms of relevant systematic errors can go undetected when the currently prevalent metrics for IMRT/VMAT commissioning are used. If alternative methods and metrics are used instead of (or in addition to) the conventional metrics, these errors are more likely to be detected, and only once they are detected can they be properly diagnosed and rooted out of the system. Removing systematic errors should be a goal not only of commissioning by the end users but also product validation by the manufacturers. For any systematic errors that cannot be removed, detecting and quantifying them is important as it will help the physicist understand the limits of the system and work with the manufacturer on improvements. In summary, IMRT and VMAT commissioning, along with product validation, would benefit from the retirement of the 3%/3 mm passing rates as a primary metric of performance, and the adoption instead of tighter tolerances, more diligent diagnostics, and more thorough analysis.

  10. U.S. Representatives Newhouse, Heck Tour Hanford Site Projects, Facilities

    Energy Savers [EERE]

    Department of Energy Removes Nine Metric Tons of Plutonium From Nuclear Weapons Stockpile U.S. Removes Nine Metric Tons of Plutonium From Nuclear Weapons Stockpile September 17, 2007 - 2:41pm Addthis Declaration Reinforces U.S. Commitment to Nonproliferation VIENNA, AUSTRIA - Secretary of Energy Samuel W. Bodman today announced that the Department of Energy's National Nuclear Security Administration (NNSA) will remove nine metric tons of plutonium from further use as fissile material in U.S.

  11. FY 2009 Annual Report of Joule Software Metric SC GG 3.1/2.5.2, Improve Computational Science Capabilities

    SciTech Connect (OSTI)

    Kothe, Douglas B; Roche, Kenneth J; Kendall, Ricky A

    2010-01-01

    The Joule Software Metric for Computational Effectiveness is established by Public Authorizations PL 95-91, Department of Energy Organization Act, and PL 103-62, Government Performance and Results Act. The U.S. Office of Management and Budget (OMB) oversees the preparation and administration of the President s budget; evaluates the effectiveness of agency programs, policies, and procedures; assesses competing funding demands across agencies; and sets the funding priorities for the federal government. The OMB has the power of audit and exercises this right annually for each federal agency. According to the Government Performance and Results Act of 1993 (GPRA), federal agencies are required to develop three planning and performance documents: 1.Strategic Plan: a broad, 3 year outlook; 2.Annual Performance Plan: a focused, 1 year outlook of annual goals and objectives that is reflected in the annual budget request (What results can the agency deliver as part of its public funding?); and 3.Performance and Accountability Report: an annual report that details the previous fiscal year performance (What results did the agency produce in return for its public funding?). OMB uses its Performance Assessment Rating Tool (PART) to perform evaluations. PART has seven worksheets for seven types of agency functions. The function of Research and Development (R&D) programs is included. R&D programs are assessed on the following criteria: Does the R&D program perform a clear role? Has the program set valid long term and annual goals? Is the program well managed? Is the program achieving the results set forth in its GPRA documents? In Fiscal Year (FY) 2003, the Department of Energy Office of Science (DOE SC-1) worked directly with OMB to come to a consensus on an appropriate set of performance measures consistent with PART requirements. The scientific performance expectations of these requirements reach the scope of work conducted at the DOE national laboratories. The Joule system emerged from this interaction. Joule enables the chief financial officer and senior DOE management to track annual performance on a quarterly basis. Joule scores are reported as success, goal met (green light in PART), mixed results, goal partially met (yellow light in PART), and unsatisfactory, goal not met (red light in PART). Joule links the DOE strategic plan to the underlying base program targets.

  12. Unpolarised TMD Distribution and Fragmentation Functions from recent HERMES and COMPASS Semi-inclusive Deep Inelastic Scattering Multiplicities

    SciTech Connect (OSTI)

    Prokudin, Alexey; Anselmino, Mauro; Boglione, Mariaelena; Melis, Stefano; Gonzalez, J. O.

    2014-10-01

    The unpolarised transverse momentum dependent distribution and fragmentation functions (TMDs) are extracted from HERMES and COMPASS experimental measurements of semi- inclusive deep inelastic scattering multiplicities for charged hadron production. A simple factorised functional form of the TMDs is adopted, with a Gaussian dependence on the intrinsic transverse momentum, which turns out to be quite adequate in shape.

  13. Measurement of pretzelosity asymmetry of charged pion production in semi-inclusive deep inelastic scattering on a polarized He target

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhang, Y.; Qian, X.; Allada, K.; Dutta, C.

    2014-11-01

    An experiment to measure single-spin asymmetries in semi-inclusive production of charged pions in deep-inelastic scattering on a transversely polarized He target was performed at Jefferson Lab in the kinematic region of 0.16 on He3 and on neutron pretzelosity asymmetries are consistent with zero within experimental uncertainties.

  14. President Obama Announces Commitments and Executive Actions to...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    create jobs and cut carbon pollution by advancing solar deployment and energy efficiency. ... smarter appliances that will cut carbon pollution by more than 380 million metric tons - ...

  15. Categorical Exclusion B5.13 Supporting Information for DOE Notice...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Amt Injection metric tonnes (short tons) Injection Scheduled ... Feasibilitysafety of coal seam sequestration ... 8 MGSC Oil-bearing Well Conversion Employ advanced MVA ...

  16. Microsoft Word - Cover.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... CO 2 metric tons Sector-Specific Industrial ... Emissions From Purchased Energy for Emission Reductions (Not included in emissions ... Generating Efficiency** % J Electrical ...

  17. About

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    science, people, technologies close Raising the bar on carbon capture In the United States, industry produces more than 3 billion metric tons of carbon dioxide each year, around...

  18. Albany, OR * Anchorage, AK * Morgantown, WV * Pittsburgh, PA...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Simon saline formation. The CO 2 pipeline will originate at the Meredosia power plant site and transport approximately 1 million metric tons (MMT) per year of compressed and ...

  19. DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Metric Tons of U.S. CO2 Storage Resource | Department of Energy Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion Metric Tons of U.S. CO2 Storage Resource DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion Metric Tons of U.S. CO2 Storage Resource December 19, 2012 - 12:00pm Addthis Washington, DC - The United States has at least 2,400 billion metric tons of possible carbon dioxide (CO2) storage resource in saline formations, oil and gas

  20. SAS Output

    U.S. Energy Information Administration (EIA) Indexed Site

    1. Emissions from Energy Consumption at Conventional Power Plants and Combined-Heat-and-Power Plants 2004 through 2014 (Thousand Metric Tons) Year Carbon Dioxide (CO2) Sulfur ...

  1. EIS-0276: Rocky Flats Plutonium Storage, Golden, Colorado

    Broader source: Energy.gov [DOE]

    This EIS analyzes DOE's proposed action to provide safe interim storage of approximately 10 metric tons of plutonium at the Rocky Flats Environmental Technology Site (RFETS).

  2. GREET Life-Cycle Analysis of Biofuels

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... and data to Billion Ton Study Sustainability Chapter in collaboration with other ... and academia use to assess life-cycle energy and environmental metrics of biofuels. ...

  3. National Renewable Energy Laboratory Environmental Performance...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    apparatus, product, or process ...yr Million metrics tons of carbon per year NEPA National Environmental Policy Act NESHAPs ... 30 4.4 Sustainability and the ...

  4. Energy Markets

    U.S. Energy Information Administration (EIA) Indexed Site

    will show a lower growth trajectory Source: EIA, International Energy Outlook 2013 carbon dioxide emissions billion metric tons 6 CSIS | Energy Markets Outlook November 16,...

  5. Table 5. Per capita energy-related carbon dioxide emissions by...

    U.S. Energy Information Administration (EIA) Indexed Site

    Per capita energy-related carbon dioxide emissions by State (2000-2011)" "metric tons of carbon dioxide per person" ,,,"Change" ,,,"2000 to 2011"...

  6. Table 2. 2011 State energy-related carbon dioxide emissions by...

    U.S. Energy Information Administration (EIA) Indexed Site

    2011 State energy-related carbon dioxide emissions by fuel " ,"million metric tons of carbon dioxide",,,,,"shares" "State","Coal","Petroleum","Natural Gas ","Total",,"Coal","Petrol...

  7. Table 3. 2011 State energy-related carbon dioxide emissions by...

    U.S. Energy Information Administration (EIA) Indexed Site

    2011 State energy-related carbon dioxide emissions by sector " "million metric tons of carbon dioxide" "State","Commercial","Electric Power","Residential","Industrial","Transportat...

  8. Table 1. State energy-related carbon dioxide emissions by year...

    U.S. Energy Information Administration (EIA) Indexed Site

    State energy-related carbon dioxide emissions by year (2000-2011)" "million metric tons of carbon dioxide" ,,,"Change" ,,,"2000 to 2011" "State",2000,2001,2002,...

  9. Mr. John E. Kieling, Chief Hazardous Waste Bureau

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    cartridges * Electrical Ballasts * Used oi l and oil filters * Electronics * Wood pallets, spools, * Lamps timbers. and waste * Metals In FY 20 14, 185 .36 metric tons of...

  10. WIPP WASTE MINIMIZATION PROGRAM DESCRIPTION

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    salt * Paper * Plastic * Tires * Toner cartridges * Used oil and oil filters * Wood pallets * Wood waste (spools, timbers, and crating materials) In FY 2015, 170 metric tons of...

  11. New Energy Efficiency Standards for Furnace Fans to Reduce Carbon...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    by 340 million metric tons through 2030," said Energy Secretary Ernest Moniz. "These standards help Americans save money by saving energy while also protecting the environment. ...

  12. Building Technologies Office | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    furnaces will save businesses 167 billion on their utility bills and reduce carbon pollution by 885 million metric tons. Read more DOE Releases Funding Opportunity for Emerging...

  13. City of Painesville, Ohio Vanadium Redox Battery Demonstration...

    Office of Environmental Management (EM)

    with an additional 212 created by 2016 Energy costs will be reduced Power quality will be improved Carbon emissions will be reduced by 24,000 metric tons ...

  14. Two Colorado-Based Electric Cooperatives Selected as 2014 Wind...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    jobs across the country, provides cost- competitive energy, and eliminates more than 115 electric metric tons of carbon dioxide emissions which is equal to removing 20 million...

  15. Appendix A: Reference case

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Information Administration Annual Energy Outlook 2014 Table A18. Energy-related carbon dioxide emissions by sector and source (million metric tons, unless otherwise noted)...

  16. Table 8. Carbon intensity of the economy by State (2000-2011

    U.S. Energy Information Administration (EIA) Indexed Site

    Carbon intensity of the economy by State (2000-2011)" "metric tons energy-related carbon dioxide per million dollars of GDP" ,,,"Change" ,,,"2000 to 2011"...

  17. IVANPAH | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    year and prevent 500,000 metric tons of carbon dioxide emissions annually. PROJECT STATISTICS: IVANPAH PROJECT SUMMARY OWNERS BrightSource Energy, NRG Energy & Google ...

  18. GRANITE RELIABLE | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    It will prevent 130,000 metric tons of carbon dioxide emissions annually. PROJECT STATISTICS: GRANITE RELIABLE PROJECT SUMMARY OWNERS BAIF Granite Holdings & Freshet Wind ...

  19. SHEPHERDS FLAT | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    It is expected to prevent 1,000,000 metric tons of carbon dioxide emissions annually. PROJECT STATISTICS: SHEPHERDS FLAT PROJECT SUMMARY OWNER Caithness Energy, LLC LOCATIONS ...

  20. Moab Project Disposes 2 Million Tons of Uranium Mill Tailings...

    Office of Environmental Management (EM)

    The Moab Uranium Mill Tailings Remedial Action Project reached its primary American ... our first 2 years of moving tailings," Moab Federal Project Director Donald Metzler said. ...

  1. Moab Marks 6-Million-Ton Cleanup Milestone

    Broader source: Energy.gov [DOE]

    MOAB, Utah – 6,000,000 is a big number, and it marks a significant cleanup milestone in the Beehive State.

  2. Hanford Landfill Reaches 15 Million Tons Disposed - Waste Disposal...

    Broader source: Energy.gov (indexed) [DOE]

    from reaching the groundwater and the Columbia River. ERDF receives contaminated soil, demolition debris, and solid waste from cleanup operations across the...

  3. Department of Energy Releases New 'Billion-Ton' Study Highlighting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    impacting other vital U.S. farm and forest products, such as food, feed, and fiber crops. ... in-depth analyses of land-use changes and competition among food, feed, and energy crops. ...

  4. KCP relocates 18-ton machine | National Nuclear Security Administratio...

    National Nuclear Security Administration (NNSA)

    relocations. It took nearly three days to disassemble the machine and prepare it for transport. The machine was partially disassembled, removing auxiliary pieces from the main...

  5. Energy Department Employee Recognized for Eliminating One Million Tons of

    Broader source: Energy.gov (indexed) [DOE]

    Development | Department of Energy The Energy Department today issued a Geothermal Regulatory Roadmap that will help developers navigate regulatory requirements at every level of government to deploy geothermal energy projects. In partnership with the Bureau of Land Management, U.S. Fish and Wildlife Service, and U.S. Forest Service, the Energy Department enlisted the National Renewable Energy Laboratory to convene key federal, state, and local permitting officials, along with industry

  6. 14,700 tons of silver at Y-12

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    calutron magnets was because of a shortage of copper during the war. As you will recall, Gen. Groves sent Col. Nichols to arrange for the purchase of as much uranium ore as could...

  7. THE POSSIBLE ROLE OF CORONAL STREAMERS AS MAGNETICALLY CLOSED STRUCTURES IN SHOCK-INDUCED ENERGETIC ELECTRONS AND METRIC TYPE II RADIO BURSTS

    SciTech Connect (OSTI)

    Kong, Xiangliang; Chen, Yao; Feng, Shiwei; Wang, Bing; Du, Guohui; Guo, Fan; Li, Gang

    2015-01-10

    Two solar typeII radio bursts, separated by ?24 hr in time, are examined together. Both events are associated with coronal mass ejections (CMEs) erupting from the same active region (NOAA 11176) beneath a well-observed helmet streamer. We find that the typeII emissions in both events ended once the CME/shock fronts passed the white-light streamer tip, which is presumably the magnetic cusp of the streamer. This leads us to conjecture that the closed magnetic arcades of the streamer may play a role in electron acceleration and typeII excitation at coronal shocks. To examine such a conjecture, we conduct a test-particle simulation for electron dynamics within a large-scale partially closed streamer magnetic configuration swept by a coronal shock. We find that the closed field lines play the role of an electron trap via which the electrons are sent back to the shock front multiple times and therefore accelerated to high energies by the shock. Electrons with an initial energy of 300 eV can be accelerated to tens of keV concentrating at the loop apex close to the shock front with a counter-streaming distribution at most locations. These electrons are energetic enough to excite Langmuir waves and radio bursts. Considering the fact that most solar eruptions originate from closed field regions, we suggest that the scenario may be important for the generation of more metric typeIIs. This study also provides an explanation of the general ending frequencies of metric typeIIs at or above 20-30 MHz and the disconnection issue between metric and interplanetary typeIIs.

  8. Two (2) 175 Ton (350 Tons total) Chiller Geothermal Heat Pumps for recently commissioned LEED Platinum Building

    Broader source: Energy.gov [DOE]

    This project will operate; collect data; and market the energy savings and capital costs of a recently commissioned chiller geothermal heat pump project to promote the wide-spread adoption of this mature technology.

  9. Semi-inclusive studies of semileptonic B-s decays at Belle

    SciTech Connect (OSTI)

    Oswald, Christian; Urquijo, P.; Dingfelder, J.; Abdesselam, A.; Adachi, I.; Aihara, H.; Al Said, S.; Asner, David M.; Aushev, T.; Ayad, R.; Babu, V.; Badhrees, I.; Bakich, A. M.; Bhardwaj, V.; Bobrov, A.; Bonvicini, Giovanni; Bozek, A.; Bracko, Marko; Browder, Thomas E.; Cervenkov, D.; Chang, M-C; Chekelian, V.; Chen, A.; Cheon, B. G.; Chilikin, K.; Cho, K.; Chobanova, V.; Choi, Y.; Cinabro, David A.; Dalseno, J.; Dolezal, Z.; Drasal, Z.; Drutskoy, A.; Dutta, D.; Eidelman, S.; Farhat, H.; Fast, James E.; Ferber, T.; Frost, O.; Fulsom, Bryan G.; Gaur, Vipin; Gabyshev, N.; Ganguly, Sudeshna; Garmash, A.; Getzkow, D.; Gillard, R.; Glattaur, R.; Goh, Y. M.; Goldenzweig, P.; Golob, B.; Grzymkowska, O.; Hara, Takanori; Hasenbusch, J.; Hayasaka, K.; Hayashii, H.; He, X. H.; Hou, W. S.; Huschle, Matthias J.; Hyun, H. J.; Iijima, T.; Ishikawa, A.; Itoh, R.; Iwasaki, Y.; Jaegle, Igal; Julius, T.; Kang, K. H.; Kapusta, P.; Kato, E.; Kawasaki, T.; Kiesling, C.; Kim, D. Y.; Kim, J. B.; Kim, J. H.; Kim, K. T.; Kim, M. J.; Kim, S. H.; Kim, Y. J.; Kinoshita, Kay; Ko, Byeong Rok; Kodys, P.; Korpar, S.; Krizan, P.; Krokovny, Pavel; Kuhr, T.; Kumita, T.; Kwon, Y. J.; Lange, J. S.; Lee, D. H.; Lee, I. S.; Li, Y.; Gioi, LL; Libby, J.; Liventsev, D.; Lukin, P.; Matvienko, D.; Miyata, H.; Mizuk, R.; Mohanty, G. B.; Moll, A.; Moon, H K.; Nakano, E.; Nakao, M.; Nakazawa, H.; Nanut, T.; Natkaniec, Z.; Nayak, Minakshi; Nishida, S.; Nozaki, T.; Okuno, S.; Pakhlov, P.; Pakhlova, G.; Park, C. W.; Park, H.; Pedlar, Todd; Pesantez, L.; Pestotnik, R.; Petric, M.; Piilonen, Leo E.; Pulvermacher, C.; Ribezl, Eva; Ritter, M.; Rostomyan, A.; Rozanska, M.; Ryu, S.; Sakai, Y.; Sandilya, Saurabh; Santelj, L.; Sanuki, T.; Sato, Y.; Savinov, Vladimir; Schneider, O.; Schnell, G.; Schwanda, C.; Semmler, D.; Senyo, K.; Seon, O.; Sevior, ME; Shapkin, M.; Shebalin, V.; Shen, CP; Shibata, TA; Shiu, Jing-Ge; Sibidanov, A.; Simon, F.; Sohn, Y. S.; Solovieva, E.; Stanic, S.; Staric, M.; Stypula, J.; Sumihama, M.; Sumiyoshi, T.; Tamponi, Umberto; Teramoto, Y.; Trabelsi, K.; Uchida, M.; Unno, Y.; Uno, S.; Usov, Y.; Van Hulse, C.; Vanhoefer, P.; Varner, G.; Vinokurova, A.; Vorobyev, V.; Vossen, Anslem G.; Wagner, M. N.; Wang, C. H.; Wang, M. Z.; Wang, P.; Wang, Xiaolong; Watanabe, Y.; Williams, K. M.; Won, E.; Yamamoto, H.; Yashchenko, S.; Yook, Youngmin; Zhang, Z. P.; Zhilich, V.; Zhulanov, V.; Zupanc, A.

    2015-10-22

    We present an analysis of the semi-inclusive decays B-s -> D(s)(-)Xl(+)nu and B-s -> D-s*(-)Xl(+)nu, where X denotes a final state that may consist of additional hadrons or photons and l is an electron or muon. The studied Bs decays are contained in the 121.4 fb(-1) Upsilon(5S) data sample collected by the Belle detector at the KEKB asymmetric-energy e(+)e(-) collider. The branching fractions of the decays are measured to be B(B-s -> D(s)(-)Xl(+)nu) = [8.2 +/- 0.2(stat) +/- 0.6(syst) +/- 1.4(ext)] % and B(B-s -> D-s*(-)Xl(+)nu) = [5.4 +/- 0.4(stat) +/- 0.4(syst) +/- 0.9(ext)] %, where the first two uncertainties are statistical and systematic and the last is due to external parameters. The measurement also provides an estimate of the B-s(()*())(B) over bar (()(s)*()) production cross section, sigma(e(+)e(-) -> B-s(()*())(B) over bar (()(s)*())) = 53.8 +/- 1.4(stat) +/- 4.0(syst) +/- 3.4(ext)] pb, at the center-of-mass energy root s = 10.86 GeV.

  10. Inclusive J/{psi} production in {Upsilon} decay via color-singlet mechanism

    SciTech Connect (OSTI)

    He Zhiguo; Wang Jianxiong

    2010-03-01

    In this work, we have calculated the tree level color-singlet contribution to the inclusive J/{psi} production in {Upsilon} decay of the {alpha}{sub s}{sup 5} order QCD process {Upsilon}{yields}J/{psi}+ccg and {alpha}{sup 2{alpha}}{sub s}{sup 2} order QED processes {Upsilon}{yields}{gamma}*{yields}J/{psi}+cc and {Upsilon}{yields}J/{psi}+gg. It is found that the contribution of the QED processes is comparable with that of the QCD process and the numerical results of the QCD process alone are about an order of magnitude smaller than the previous theoretical predictions. Our prediction in total is 4.2x10{sup -5} which is about an order of magnitude smaller than the recent CLEO measurement on the branching fraction B({Upsilon}{yields}J/{psi}+X). It indicates that the J/{psi} production mechanism in {Upsilon} decay is not well understood and further theoretical work and experimental analysis are still necessary.

  11. Noniterative Inclusion of the Triply and Quadruply Excited Clusters: The Locally Renormalized Perspective

    SciTech Connect (OSTI)

    Kowalski, Karol; De Jong, Wibe A.

    2006-08-31

    Noniterative inclusion of the higher=order clusters has been a subject of intensive studies aimed at developing a well balanced description of individual many-body contributions for entire ground-state potential energy surfaces. In traditional approaches, the connected quadruples are estimated directly based on perturbative arguments, which leads to excellent agreement with full CI results near the equilibrium geometry and increasingly worse energies for larger internuclear stretches. As a possible improvement to this situation, two techniques are considered as especially promising: perturbative approaches based on the similarity transformed Hamiltonians and renormalization schemes both in global and local formulation. Following the latter strategy we adopted the recently introduced Numerator-Denominator Connected expansion (NDC) [ K. Kowalski, P. Piecuch, J. Chem. Phys. 122 (2005) [074107] as an effective tool for designing new forms of noniterative corrections accounting for the joint effect of triples and quadruples. The performance of the ensuing locally renormalized CCSD(TQ) approaches (LR-CCSD(TQ) is illustrated on several examples that require either going beyond the triples approximation or describing very subtle effects encountered in Van der Waals complexes. Comparisons with other noniterative approaches are also made and some issues regarding the size-extensivity of the locally renormalized methods are addressed.

  12. Dilaton field minimally coupled to 2+1 gravity; uniqueness of the static Chan-Mann black hole and new dilaton stationary metrics

    SciTech Connect (OSTI)

    García-Diaz, Alberto A.

    2014-01-14

    Using the Schwarzschild coordinate frame for a static cyclic symmetric metric in 2+1 gravity coupled minimally to a dilaton logarithmically depending on the radial coordinate in the presence of an exponential potential, by solving first order linear Einstein equations, the general solution is derived and it is identified with the Chan–Mann dilaton solution. In these coordinates, a new stationary dilaton solution is obtained; it does not allow for a de Sitter–Anti-de Sitter limit at spatial infinity, where its structural functions increase indefinitely. On the other hand, it is horizonless and allows for a naked singularity at the origin of coordinates; moreover, one can identify at a large radial coordinate a (quasi-local) mass parameter and in the whole space a constant angular momentum. Via a general SL(2,R)–transformation, applied on the static cyclic symmetric metric, a family of stationary dilaton solutions has been generated. A particular SL(2,R)–transformation is identified, which gives rise to the rotating Chan–Mann dilaton solution. All the exhibited solutions have been characterized by their quasi-local energy, mass, and momentum through their series expansions at spatial infinity. The algebraic structure of the Ricci–energy-momentum, and Cotton tensors is given explicitly.

  13. CT head-scan dosimetry in an anthropomorphic phantom and associated measurement of ACR accreditation-phantom imaging metrics under clinically representative scan conditions

    SciTech Connect (OSTI)

    Brunner, Claudia C.; Stern, Stanley H.; Chakrabarti, Kish; Minniti, Ronaldo; Parry, Marie I.; Skopec, Marlene

    2013-08-15

    Purpose: To measure radiation absorbed dose and its distribution in an anthropomorphic head phantom under clinically representative scan conditions in three widely used computed tomography (CT) scanners, and to relate those dose values to metrics such as high-contrast resolution, noise, and contrast-to-noise ratio (CNR) in the American College of Radiology CT accreditation phantom.Methods: By inserting optically stimulated luminescence dosimeters (OSLDs) in the head of an anthropomorphic phantom specially developed for CT dosimetry (University of Florida, Gainesville), we measured dose with three commonly used scanners (GE Discovery CT750 HD, Siemens Definition, Philips Brilliance 64) at two different clinical sites (Walter Reed National Military Medical Center, National Institutes of Health). The scanners were set to operate with the same data-acquisition and image-reconstruction protocols as used clinically for typical head scans, respective of the practices of each facility for each scanner. We also analyzed images of the ACR CT accreditation phantom with the corresponding protocols. While the Siemens Definition and the Philips Brilliance protocols utilized only conventional, filtered back-projection (FBP) image-reconstruction methods, the GE Discovery also employed its particular version of an adaptive statistical iterative reconstruction (ASIR) algorithm that can be blended in desired proportions with the FBP algorithm. We did an objective image-metrics analysis evaluating the modulation transfer function (MTF), noise power spectrum (NPS), and CNR for images reconstructed with FBP. For images reconstructed with ASIR, we only analyzed the CNR, since MTF and NPS results are expected to depend on the object for iterative reconstruction algorithms.Results: The OSLD measurements showed that the Siemens Definition and the Philips Brilliance scanners (located at two different clinical facilities) yield average absorbed doses in tissue of 42.6 and 43.1 mGy, respectively. The GE Discovery delivers about the same amount of dose (43.7 mGy) when run under similar operating and image-reconstruction conditions, i.e., without tube current modulation and ASIR. The image-metrics analysis likewise showed that the MTF, NPS, and CNR associated with the reconstructed images are mutually comparable when the three scanners are run with similar settings, and differences can be attributed to different edge-enhancement properties of the applied reconstruction filters. Moreover, when the GE scanner was operated with the facility's scanner settings for routine head exams, which apply 50% ASIR and use only approximately half of the 100%-FBP dose, the CNR of the images showed no significant change. Even though the CNR alone is not sufficient to characterize the image quality and justify any dose reduction claims, it can be useful as a constancy test metric.Conclusions: This work presents a straightforward method to connect direct measurements of CT dose with objective image metrics such as high-contrast resolution, noise, and CNR. It demonstrates that OSLD measurements in an anthropomorphic head phantom allow a realistic and locally precise estimation of magnitude and spatial distribution of dose in tissue delivered during a typical CT head scan. Additional objective analysis of the images of the ACR accreditation phantom can be used to relate the measured doses to high contrast resolution, noise, and CNR.

  14. Measurement of pretzelosity asymmetry of charged pion production in semi-inclusive deep inelastic scattering on a polarized He target

    SciTech Connect (OSTI)

    Zhang, Y.; Qian, X.; Allada, K.; Dutta, C.

    2014-11-01

    An experiment to measure single-spin asymmetries in semi-inclusive production of charged pions in deep-inelastic scattering on a transversely polarized He target was performed at Jefferson Lab in the kinematic region of 0.16 < x < 0.35 and 1.4 < Q < 2.7 GeV. Our results show that both ? on He3 and on neutron pretzelosity asymmetries are consistent with zero within experimental uncertainties.

  15. Magnetic properties of MnSb inclusions formed in GaSb matrix directly during molecular beam epitaxial growth

    SciTech Connect (OSTI)

    Lawniczak-Jablonska, Krystyna; Wolska, Anna; Klepka, Marcin T.; Kret, Slawomir; Kurowska, Boguslawa; Kowalski, Bogdan J.; Twardowski, Andrzej; Wasik, Dariusz; Kwiatkowski, Adam; Sadowski, Janusz

    2011-04-01

    Despite of intensive search for the proper semiconductor base materials for spintronic devices working at room temperature no appropriate material based on ferromagnetic semiconductors has been found so far. We demonstrate that the phase segregated system with MnSb hexagonal inclusions inside the GaSb matrix, formed directly during the molecular beam epitaxial growth reveals the ferromagnetic properties at room temperature and is a good candidate for exploitation in spintronics. Furthermore, the MnSb inclusions with only one crystalline structure were identified in this GaMn:MnSb granular material. The SQUID magnetometry confirmed that this material exhibits ferromagnetic like behavior starting from helium up to room temperature. Moreover, the magnetic anisotropy was found which was present also at room temperature, and it was proved that by choosing a proper substrate it is possible to control the direction of easy axis of inclusions' magnetization moment between in-plane and out-of-plane; the latter is important in view of potential applications in spintronic devices.

  16. Diamonds in the rough: a strong case for the inclusion of weak-intensity X-ray diffraction data

    SciTech Connect (OSTI)

    Wang, Jimin; Wing, Richard A.

    2014-05-01

    Here, new evidence is provided to show that the inclusion of weak-intensity, high-resolution X-ray diffraction data helps to improve the quality of experimental phases by imposing proper constraints on electron-density models during noncrystallographic symmetry averaging. Overwhelming evidence exists to show that the inclusion of weak-intensity, high-resolution X-ray diffraction data helps improve the refinement of atomic models by imposing strong constraints on individual and overall temperature B factors and thus the quality of crystal structures. Some researchers consider these data to be of little value and opt to discard them during data processing, particularly at medium and low resolution, at which individual B factors of atomic models cannot be refined. Here, new evidence is provided to show that the inclusion of these data helps to improve the quality of experimental phases by imposing proper constraints on electron-density models during noncrystallographic symmetry (NCS) averaging. Using electron-density correlation coefficients as criteria, the resolution of data has successfully been extended from 3.1 to 2.5 Å resolution with redundancy-independent merging R factors from below 100% to about 310%. It is further demonstrated that phase information can be fully extracted from observed amplitudes through de novo NCS averaging. Averaging starts with uniform density inside double-shelled spherical masks and NCS matrices that are derived from bound heavy-atom clusters at the vertices of cuboctahedrally symmetric protein particles.

  17. Precision measurement of the longitudinal double-spin asymmetry for inclusive jet production in polarized proton collisions at √s = 200 GeV

    SciTech Connect (OSTI)

    Adamczyk, L.

    2015-08-26

    We report a new measurement of the midrapidity inclusive jet longitudinal double-spin asymmetry, ALL, in polarized pp collisions at center-of-mass energy √s = 200 GeV. The STAR data place stringent constraints on polarized parton distribution functions extracted at next-to-leading order from global analyses of inclusive deep-inelastic scattering (DIS), semi-inclusive DIS, and RHIC pp data. Lastly, the measured asymmetries provide evidence at the 3σ level for positive gluon polarization in the Bjorken-x region x > 0.05 .

  18. Precision measurement of the longitudinal double-spin asymmetry for inclusive jet production in polarized proton collisions at √s = 200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.

    2015-08-26

    We report a new measurement of the midrapidity inclusive jet longitudinal double-spin asymmetry, ALL, in polarized pp collisions at center-of-mass energy √s = 200 GeV. The STAR data place stringent constraints on polarized parton distribution functions extracted at next-to-leading order from global analyses of inclusive deep-inelastic scattering (DIS), semi-inclusive DIS, and RHIC pp data. Lastly, the measured asymmetries provide evidence at the 3σ level for positive gluon polarization in the Bjorken-x region x > 0.05 .

  19. Precision Measurement of the Longitudinal Double-Spin Asymmetry for Inclusive Jet Production in Polarized Proton Collisions at ?s=200GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.

    2015-08-26

    We report a new measurement of the midrapidity inclusive jet longitudinal double-spin asymmetry, A LL , in polarized pp collisions at center-of-mass energy ?s =200 GeV . The STAR data place stringent constraints on polarized parton distribution functions extracted at next-to-leading order from global analyses of inclusive deep-inelastic scattering (DIS), semi-inclusive DIS, and RHIC pp data. The measured asymmetries provide evidence at the 3? level for positive gluon polarization in the Bjorken-x region x>0.05 .

  20. Branching Fraction and CP Asymmetry Measurements in Inclusive B ? Xs ???? and B ? Xs? Decays from BABAR

    SciTech Connect (OSTI)

    Eigen, G.

    2015-04-29

    We present an update on total and partial branching fractions and on CP asymmetries in the semi-inclusive decay B ? Xs???-. Further, we summarize our results on branching fractions and CP asymmetries for semi-inclusive and fully-inclusive B ? Xs? decays. We present the first result on the CP asymmetry diff erence of charged and neutral B ? Xs? decays yielding the first constraint on the ratio of Wilson coeffi cients Im(C8eff/C7eff).

  1. Word Pro - Untitled1

    U.S. Energy Information Administration (EIA) Indexed Site

    Source: Table 11.4. 1980 1985 1990 1995 2000 2005 0.0 0.3 0.6 0.9 Million Metric Tons of Nitrous Oxide 1980 1985 1990 1995 2000 2005 0 50 100 150 200 Thousand Metric Tons of ...

  2. Measurement of the Inclusive Jet Cross Section in pp Collisions at √s=7 TeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Chatrchyan, S.; Khachatryan, V.; Sirunyan, A. M.; Tumasyan, A.; Adam, W.; Bergauer, T.; Dragicevic, M.; Erö, J.; Fabjan, C.; Friedl, M.; et al

    2011-09-19

    The inclusive jet cross section is measured in pp collisions with a center-of-mass energy of 7 TeV at the Large Hadron Collider using the CMS experiment. The data sample corresponds to an integrated luminosity of 34 pb⁻¹. The measurement is made for jet transverse momenta in the range 18–1100 GeV and for absolute values of rapidity less than 3. The measured cross section extends to the highest values of jet pT ever observed and, within the experimental and theoretical uncertainties, is generally in agreement with next-to-leading-order perturbative QCD predictions.

  3. Measurement of the inclusive semileptonic branching fraction B(B⁰s→X-l+νl) at Belle

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Oswald, C.; Urquijo, P.; Dingfelder, J.; Adachi, I.; Aihara, H.; Arinstein, K.; Asner, D. M.; Aushev, T.; Bakich, A. M.; Belous, K.; et al

    2013-04-30

    We report a measurement of the inclusive semileptonic B0s branching fraction in a 121 fb⁻¹ data sample collected near the Υ(5S) resonance with the Belle detector at the KEKB asymmetric energy e⁺e⁻ collider. Events containing B⁰(*)sB¯¯¯⁰(*)s pairs are selected by reconstructing a tag side D⁺s and identifying a signal side lepton l⁺ (l=e, μ) that is required to have the same-sign charge to ensure that both originate from different B⁰s mesons. The B⁰s→X⁻l⁺νl branching fraction is extracted from the ratio of the measured yields of D⁺s mesons and D⁺sl⁺ pairs and the known production and branching fractions. The inclusive semileptonicmore » branching fraction is measured to be [10.6±0.5(stat)±0.7(syst)]%.« less

  4. Measurement of the inclusive semileptonic branching fraction B(B⁰s→X-l+νl) at Belle

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Oswald, C.; Urquijo, P.; Dingfelder, J.; Adachi, I.; Aihara, H.; Arinstein, K.; Asner, D. M.; Aushev, T.; Bakich, A. M.; Belous, K.; et al

    2013-04-30

    We report a measurement of the inclusive semileptonic B0s branching fraction in a 121 fb⁻¹ data sample collected near the Υ(5S) resonance with the Belle detector at the KEKB asymmetric energy e⁺e⁻ collider. Events containing B⁰(*)sB¯¯¯⁰(*)s pairs are selected by reconstructing a tag side D⁺s and identifying a signal side lepton l⁺ (l=e, μ) that is required to have the same-sign charge to ensure that both originate from different B⁰s mesons. The B⁰s→X⁻l⁺νl branching fraction is extracted from the ratio of the measured yields of D⁺s mesons and D⁺sl⁺ pairs and the known production and branching fractions. The inclusive semileptonicmore »branching fraction is measured to be [10.6±0.5(stat)±0.7(syst)]%.« less

  5. The Oil Security Metrics Model: A Tool for Evaluating the Prospective Oil Security Benefits of DOE's Energy Efficiency and Renewable Energy R&D Programs

    SciTech Connect (OSTI)

    Greene, David L; Leiby, Paul Newsome

    2006-05-01

    Energy technology R&D is a cornerstone of U.S. energy policy. Understanding the potential for energy technology R&D to solve the nation's energy problems is critical to formulating a successful R&D program. In light of this, the U.S. Congress requested the National Research Council (NRC) to undertake both retrospective and prospective assessments of the Department of Energy's (DOE's) Energy Efficiency and Fossil Energy Research programs (NRC, 2001; NRC, 2005). ("The Congress continued to express its interest in R&D benefits assessment by providing funds for the NRC to build on the retrospective methodology to develop a methodology for assessing prospective benefits." NRC, 2005, p. ES-2) In 2004, the NRC Committee on Prospective Benefits of DOE's Energy Efficiency and Fossil Energy R&D Programs published a report recommending a new framework and principles for prospective benefits assessment. The Committee explicitly deferred the issue of estimating security benefits to future work. Recognizing the need for a rigorous framework for assessing the energy security benefits of its R&D programs, the DOE's Office of Energy Efficiency and Renewable Energy (EERE) developed a framework and approach for defining energy security metrics for R&D programs to use in gauging the energy security benefits of their programs (Lee, 2005). This report describes methods for estimating the prospective oil security benefits of EERE's R&D programs that are consistent with the methodologies of the NRC (2005) Committee and that build on Lee's (2005) framework. Its objective is to define and implement a method that makes use of the NRC's typology of prospective benefits and methodological framework, satisfies the NRC's criteria for prospective benefits evaluation, and permits measurement of that portion of the prospective energy security benefits of EERE's R&D portfolio related to oil. While the Oil Security Metrics (OSM) methodology described in this report has been specifically developed to estimate the prospective oil security benefits of DOE's R&D programs, it is also applicable to other strategies and policies aimed at changing U.S. petroleum demand.

  6. Commercial Building Energy Baseline Modeling Software: Performance Metrics and Method Testing with Open Source Models and Implications for Proprietary Software Testing

    SciTech Connect (OSTI)

    Price, Phillip N.; Granderson, Jessica; Sohn, Michael; Addy, Nathan; Jump, David

    2013-09-01

    The overarching goal of this work is to advance the capabilities of technology evaluators in evaluating the building-level baseline modeling capabilities of Energy Management and Information System (EMIS) software. Through their customer engagement platforms and products, EMIS software products have the potential to produce whole-building energy savings through multiple strategies: building system operation improvements, equipment efficiency upgrades and replacements, and inducement of behavioral change among the occupants and operations personnel. Some offerings may also automate the quantification of whole-building energy savings, relative to a baseline period, using empirical models that relate energy consumption to key influencing parameters, such as ambient weather conditions and building operation schedule. These automated baseline models can be used to streamline the whole-building measurement and verification (M&V) process, and therefore are of critical importance in the context of multi-measure whole-building focused utility efficiency programs. This report documents the findings of a study that was conducted to begin answering critical questions regarding quantification of savings at the whole-building level, and the use of automated and commercial software tools. To evaluate the modeling capabilities of EMIS software particular to the use case of whole-building savings estimation, four research questions were addressed: 1. What is a general methodology that can be used to evaluate baseline model performance, both in terms of a) overall robustness, and b) relative to other models? 2. How can that general methodology be applied to evaluate proprietary models that are embedded in commercial EMIS tools? How might one handle practical issues associated with data security, intellectual property, appropriate testing ‘blinds’, and large data sets? 3. How can buildings be pre-screened to identify those that are the most model-predictable, and therefore those whose savings can be calculated with least error? 4. What is the state of public domain models, that is, how well do they perform, and what are the associated implications for whole-building measurement and verification (M&V)? Additional project objectives that were addressed as part of this study include: (1) clarification of the use cases and conditions for baseline modeling performance metrics, benchmarks and evaluation criteria, (2) providing guidance for determining customer suitability for baseline modeling, (3) describing the portfolio level effects of baseline model estimation errors, (4) informing PG&E’s development of EMIS technology product specifications, and (5) providing the analytical foundation for future studies about baseline modeling and saving effects of EMIS technologies. A final objective of this project was to demonstrate the application of the methodology, performance metrics, and test protocols with participating EMIS product vendors.

  7. Assessment of thermal evolution stages and oil-gas migration of carbonate source rocks of early tertiary in eastern Sichuan, China, by organic inclusion analysis

    SciTech Connect (OSTI)

    Shi Jixi; Li Benchao; Fu Jiamo

    1989-03-01

    The Jialinjiang Formation of early Tertiary in Sichuan, China, is a series of limestone and dolomite sediments deposited in a platform shoal environment. The diagenetic sequence and organic inclusions trapped in minerals of 95 samples from 20 drillings have been studied. At the late diagenetic stage, pale yellow organic inclusions consisted of liquid hydrocarbons disseminated in pore-infiltrating dolomite, and the homogeneous temperature of contemporaneous saline liquid inclusions possessing a low gas-liquid ratio was 86/degree/C. This indicates the evolution of the organic matter had gone over the oil generating threshold and oil formation had initiated. In the limestone formed at the late diagenetic stage, more brown-yellow organic inclusions were scattered and/or developed along with fissures, comprising 60-70% liquid hydrocarbons and 30-40% gaseous hydrocarbons. Contemporaneous saline liquid inclusions with gas-liquid ratios of 5-10% had homogeneous temperatures of 90/degree/-130/degree/C. These findings show that the organic material had entered a high evolution stage and oil migration had taken place on a large scale.

  8. Inclusive b-hadron production cross section with muons in pp collisions at sqrt(s) = 7 TeV

    SciTech Connect (OSTI)

    Khachatryan, Vardan; et al.

    2011-03-01

    A measurement of the b-hadron production cross section in proton-proton collisions at sqrt(s)=7 TeV is presented. The dataset, corresponding to 85 inverse nanobarns, was recorded with the CMS experiment at the LHC using a low-threshold single-muon trigger. Events are selected by the presence of a muon with transverse momentum greater than 6 GeV with respect to the beam direction and pseudorapidity less than 2.1. The transverse momentum of the muon with respect to the closest jet discriminates events containing b hadrons from background. The inclusive b-hadron production cross section is presented as a function of muon transverse momentum and pseudorapidity. The measured total cross section in the kinematic acceptance is sigma(pp to b+X to mu + X') =1.32 +/- 0.01 (stat) +/- 0.30 (syst) +/- 0.15 (lumi) microbarns.

  9. Single Spin Asymmetries of Inclusive Hadrons Produced in Electron Scattering from a Transversely Polarized 3He Target

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Allada, Kalyan; Zhao, Yongxiang; Aniol, Konrad; Annand, John; Averett, Todd; Benmokhtar, Fatiha; Bertozzi, William; Bradshaw, Peter; Bosted, Peter; Camsonne, Alexandre; et al

    2014-04-01

    We report the first measurement of target single-spin asymmetries (AN) in the inclusive hadron production reaction, e + 3He??h+X, using a transversely polarized 3 He target. The experiment was conducted at Jefferson Lab in Hall A using a 5.9-GeV electron beam. Three types of hadrons (?, K and proton) were detected in the transverse hadron momentum range 0.54 T F for pions was -0.29 FF+ and K+. Amorenegative asymmetry is observed for ?. The magnitudes of the asymmetries follow |A? |? +|K +|. The K and proton asymmetries are consistent with zero within the experimental uncertainties. The ?+ and ? asymmetries measured for the 3He target and extracted for neutrons are opposite in sign with a small increase observed as a function of pT.less

  10. A File System Utilization Metric

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in order to ensure resources are adequately provisioned. Although it is relatively straightforward to- day to measure the total amount of IO to and from a file system, and the...

  11. DOE Project Management Update (Metrics)

    Office of Energy Efficiency and Renewable Energy (EERE)

    Michael Peek, Deputy Director, Office of Project Management Oversight and Assessments March 22, 2016

  12. Single spin asymmetries in charged kaon production from semi-inclusive deep inelastic scattering on a transversely polarized 3He target

    SciTech Connect (OSTI)

    Zhao, Y X; Wang, Y; Allada, K; Aniol, K; Annand, J R; Averett, T; Benmokhtar, F; Bertozzi, W; Bradshaw, P C; Bosted, P; Camsonne, A; Canan, M; Cates, G D; Chen, C; Chen, J -P; Chen, W; Chirapatpimol, K; Chudakov, E; Cisbani, E; Cornejo, J C; Cusanno, F; Dalton, M M; Deconinck, W; de Jager, C W; De Leo, R; Deng, X; Deur, A; Ding, H; Dolph, P A; Dutta, C; Dutta, D; El Fassi, L; Frullani, S; Gao, H; Garibaldi, F; Gaskell, D; Gilad, S; Gilman, R; Glamazdin, O; Golge, S; Guo, L; Hamilton, D; Hansen, O; Higinbotham, D W; Holmstrom, T; Huang, J; Huang, M; Ibrahim, H F; Iodice, M; Jiang, X; Jin, G; Jones, M K; Katich, J; Kelleher, A; Kim, W; Kolarkar, A; Korsch, W; LeRose, J J; Li, X; Li, Y; Lindgren, R; Liyanage, N; Long, E; Lu, H -J; Margaziotis, D J; Markowitz, P; Marrone, S; McNulty, D; Meziani, Z -E; Michaels, R; Moffit, B; Munoz Camacho, C; Nanda, S; Narayan, A; Nelyubin, V; Norum, B; Oh, Y; Osipenko, M; Parno, D; Peng, J -C; Phillips, S K; Posik, M; Puckett, A J; Qian, X; Qiang, Y; Rakhman, A; Ransome, R; Riordan, S; Saha, A; Sawatzky, B; Schulte, E; Shahinyan, A; Shabestari, M H; Sirca, S; Stepanyan, S; Subedi, R; Sulkosky, V; Tang, L -G; Tobias, A; Urciuoli, G M; Vilardi, I; Wang, K; Wojtsekhowski, B; Yan, X; Yao, H; Ye, Y; Ye, Z; Yuan, L; Zhan, X; Zhang, Y; Zhang, Y -W; Zhao, B; Zheng, X; Zhu, L; Zhu, X; Zong, X

    2014-11-01

    We report the first measurement of target single spin asymmetries of charged kaons produced in semi-inclusive deep inelastic scattering of electrons off a transversely polarized 3He target. Both the Collins and Sivers moments, which are related to the nucleon transversity and Sivers distributions, respectively, are extracted over the kinematic range of 0.1

  13. Single spin asymmetries in charged kaon production from semi-inclusive deep inelastic scattering on a transversely polarized 3He target

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhao, Y X; Wang, Y; Allada, K; Aniol, K; Annand, J R; Averett, T; Benmokhtar, F; Bertozzi, W; Bradshaw, P C; Bosted, P; et al

    2014-11-01

    We report the first measurement of target single spin asymmetries of charged kaons produced in semi-inclusive deep inelastic scattering of electrons off a transversely polarized 3He target. Both the Collins and Sivers moments, which are related to the nucleon transversity and Sivers distributions, respectively, are extracted over the kinematic range of 0.1

  14. Measurement and Interpretation of Moments of the Combined Hadronic Mass and Energy Spectrum in Inclusive Semileptonic B-Meson Decays

    SciTech Connect (OSTI)

    Klose, Verena; /Dresden, Tech. U.

    2011-08-12

    This thesis presents first measurements of moments of the hadronic n{sub X}{sup 2} distribution measured in inclusive semileptonic decays of B mesons to final states containing a charm quark, B {yields} X{sub c}{ell}{nu}. The variable n{sub X}{sup 2} is a combination of the invariant mass of the charmed meson m{sub X}, its energy in the B-meson rest-frame E{sub X;BRF}, and a constant {tilde {Lambda}} = 0.65 GeV, n{sub X}{sup 2} = m{sub X}{sup 2}c{sup 4}-2{tilde {Lambda}}E{sub X,BRF} + {tilde {Lambda}}{sup 2}. The moments with k = 2,4,6 are measured as proposed by theory to constrain assumptions made in the theoretical description of inclusive observables in semileptonic B-meson decays. This description uses Heavy Quark Expansion (HQE), an effective QCD combined with an Operator Product Expansion. The measurement is based on a sample of 231.6 million e{sup +}e{sup -} {yields} {Upsilon}(4S) {yields} B{bar B} events recorded with the BABAR experiment at the PEP-II e{sup +}e{sup -}-storage rings at SLAC. We reconstruct the semileptonic decay by identifying a charged lepton in events tagged by a fully reconstructed hadronic decay of the second B meson. Correction procedures are derived from Monte Carlo simulations to ensure an unbiased measurement of the moments of the n{sub X}{sup 2} distribution. All moments are measured requiring minimum lepton momenta between 0.8 GeV/c and 1.9 GeV/c in the rest frame of the B meson. Performing a simultaneous fit to the measured moments up to order k = 6 combined with other measurements of moments of the lepton-energy spectrum in decays B {yields} X{sub c}{ell}{nu} and moments of the photon-energy spectrum in decays B {yields} X{sub s}{gamma}, we determine the quark-mixing parameter |V{sub cb}|, the bottom and charm quark masses, the semileptonic branching fraction {Beta}(B {yields} X{sub c}{ell}{nu}), and four non-perturbative heavy quark parameters. Using HQE calculations in the kinetic scheme up to order 1/m{sub b}{sup 3} we find |V{sub cb}| = (41.65 {+-} 0.43 {+-} 0.40 {+-} 0.58) {center_dot} 10{sup -3} and m{sub b} = (4.570 {+-} 0.033 {+-} 0.043) GeV/c{sup 2}, where the first uncertainty refers to experimental contributions, the second to uncertainties in the HQE, and the third to theoretical uncertainties in the calculations of the semileptonic decay rate {Lambda}(B {yields} X{sub c}{ell}{nu}). All obtained results are consistent with previous determinations. The inclusion of the moments decreases the uncertainty on the HQE parameters {mu}{sub {pi}}{sup 2} and {rho}{sub D}{sup 3}. Furthermore, the theoretical treatment of higher order corrections in the HQE used for the moments has been verified with these new measurements.

  15. Inclusion property of Cs, Sr, and Ba impurities in LiCl crystal formed by layer-melt crystallization

    SciTech Connect (OSTI)

    Choi, Jung-Hoon; Cho, Yung-Zun; Lee, Tae-Kyo; Eun, Hee-Chul; Kim, Jun-Hong; Park, Hwan-Seo; Kim, In-Tae; Park, Geun-Il

    2013-07-01

    Pyroprocessing is one of the promising technologies enabling the recycling of spent nuclear fuels from a commercial light water reactor (LWR). In general, pyroprocessing uses dry molten salts as electrolytes. In particular, LiCl waste salt after pyroprocessing contains highly radioactive I/II group fission products mainly composed of Cs, Sr, and Ba impurities. Therefore, it is beneficial to reuse LiCl salt in the pyroprocessing as an electrolyte for economic and environmental issues. Herein, to understand the inclusion property of impurities within LiCl crystal, the physical properties such as lattice parameter change, bulk modulus, and substitution enthalpy of a LiCl crystal having 0-6 at% Cs{sup +} or Ba{sup 2+} impurities under existence of 1 at% Sr{sup 2+} impurity were calculated via the first-principles density functional theory. The substitution enthalpy of LiCl crystals having 1 at% Sr{sup 2+} showed slightly decreased value than those without Sr{sup 2+} impurity. Therefore, through the substitution enthalpy calculation, it is expected that impurities will be incorporated within LiCl crystal as co-existed form rather than as a single component form. (authors)

  16. Single spin asymmetries of inclusive hadrons produced in electron scattering from a transversely polarized 3 He target

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Allada, K.; Zhao, Y. X.; Aniol, K.; Annand, J. R. M.; Averett, T.; Benmokhtar, F.; Bertozzi, W.; Bradshaw, P. C.; Bosted, P.; Camsonne, A.; et al

    2014-04-07

    We report the first measurement of target single-spin asymmetries (AN) in the inclusive hadron production reaction, e + 3He↑→h+X, using a transversely polarized 3 He target. This experiment was conducted at Jefferson Lab in Hall A using a 5.9-GeV electron beam. Three types of hadrons (π±, K± and proton) were detected in the transverse hadron momentum range 0.54 < pT < 0.74 GeV/c. The range of xF for pions was -0.29 < xF< -0.23 and for kaons -0.25 < xF<-0.18. The observed asymmetry strongly depends on the type of hadron. A positive asymmetry is observed for π+ and K+. Amore » negative asymmetry is observed for π–. The magnitudes of the asymmetries follow |Aπ –|<|Aπ +|<|AK +|. The K– and proton asymmetries are consistent with zero within the experimental uncertainties. The π+ and π– asymmetries measured for the 3He target and extracted for neutrons are opposite in sign with a small increase observed as a function of pT.« less

  17. Measurements of inclusive W and Z cross sections in pp collisions at sqrt(s)=7 TeV

    SciTech Connect (OSTI)

    Khachatryan, V.; et al.,

    2011-01-01

    Measurements of inclusive W and Z boson production cross sections in pp collisions at sqrt(s)=7 TeV are presented, based on 2.9 inverse picobarns of data recorded by the CMS detector at the LHC. The measurements, performed in the electron and muon decay channels, are combined to give sigma(pp to WX) times B(W to muon or electron + neutrino) = 9.95 \\pm 0.07(stat.) \\pm 0.28(syst.) \\pm 1.09(lumi.) nb and sigma(pp to ZX) times B(Z to oppositely charged muon or electron pairs) = 0.931 \\pm 0.026(stat.) \\pm 0.023(syst.) \\pm 0.102(lumi.) nb. Theoretical predictions, calculated at the next-to-next-to-leading order in QCD using recent parton distribution functions, are in agreement with the measured cross sections. Ratios of cross sections, which incur an experimental systematic uncertainty of less than 4%, are also reported.

  18. Measurement of the parity-violating asymmetry in inclusive electroproduction of π- near the Delta0 resonance

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Androic, D.; Armstrong, D. S.; Bailey, S. L.; Beck, D. H.; Beise, E. J.; Benesch, J.; Benmokhtar, F.; Bimbot, L.; Birchall, J.; Bosted, P.; et al

    2012-03-20

    The parity-violating (PV) asymmetry of inclusive π- production in electron scattering from a liquid deuterium target was measured at backward angles. The measurement was conducted as a part of the G0 experiment, at a beam energy of 360 MeV. The physics process dominating pion production for these kinematics is quasi-free photoproduction off the neutron via the Δ0 resonance. In the context of heavy-baryon chiral perturbation theory (HBχPT), this asymmetry is related to a low energy constant dΔ- that characterizes the parity-violating γNΔ coupling. Zhu et al. calculated dΔ- in a model benchmarked by the large asymmetries seen in hyperon weakmore » radiative decays, and predicted potentially large asymmetries for this process, ranging from Aγ- = -5.2 to +5.2 ppm. The measurement performed in this work leads to Aγ- = -0.36 ± 1.06 ± 0.37 ± 0.03 ppm (where sources of statistical, systematic and theoretical uncertainties are included), which would disfavor enchancements considered by Zhu et al. proportional to Vud/Vus. The measurement is part of a program of inelastic scattering measurements that were conducted by the G0 experiment, seeking to determine the N-Δ axial transition form-factors using PV electron scattering.« less

  19. Jet mass and substructure of inclusive jets in root s=7 TeV pp collisions with the ATLAS experiment

    SciTech Connect (OSTI)

    Aad G.; Abbott, B.; Abdallah, J.; Khalek, S. Abdel; Abdelalim, A. A.; Abdesselam, A.; Abdinov, O.; Abi, B.; Abolins, M.; AbouZeid, O. S.; Abramowicz, H.; Abreu, H.; Acerbi, E.; Acharya, B. S.; Adamezyk, L.; Adams, D. L.; Addy, T. N.; Adelman, J.; Aderholz, M.; et al.

    2012-05-01

    Recent studies have highlighted the potential of jet substructure techniques to identify the hadronic decays of boosted heavy particles. These studies all rely upon the assumption that the internal substructure of jets generated by QCD radiation is well understood. In this article, this assumption is tested on an inclusive sample of jets recorded with the ATLAS detector in 2010, which corresponds to 35 pb{sup -1} of pp collisions delivered by the LHC at {radical}s = 7 TeV. In a subsample of events with single pp collisions, measurements corrected for detector efficiency and resolution are presented with full systematic uncertainties. Jet invariant mass, k{sub t} splitting scales and N-subjettiness variables are presented for anti-k{sub t} R = 1.0 jets and Cambridge-Aachen R = 1.2 jets. Jet invariant-mass spectra for Cambridge-Aachen R = 1.2 jets after a splitting and filtering procedure are also presented. Leading-order parton-shower Monte Carlo predictions for these variables are found to be broadly in agreement with data. The dependence of mean jet mass on additional pp interactions is also explored.

  20. On the Inclusion of Energy-Shifting Demand Response in Production Cost Models: Methodology and a Case Study

    SciTech Connect (OSTI)

    O'Connell, Niamh; Hale, Elaine; Doebber, Ian; Jorgenson, Jennie

    2015-07-20

    In the context of future power system requirements for additional flexibility, demand response (DR) is an attractive potential resource. Its proponents widely laud its prospective benefits, which include enabling higher penetrations of variable renewable generation at lower cost than alternative storage technologies, and improving economic efficiency. In practice, DR from the commercial and residential sectors is largely an emerging, not a mature, resource, and its actual costs and benefits need to be studied to determine promising combinations of physical DR resource, enabling controls and communications, power system characteristics, regulatory environments, market structures, and business models. The work described in this report focuses on the enablement of such analysis from the production cost modeling perspective. In particular, we contribute a bottom-up methodology for modeling load-shifting DR in production cost models. The resulting model is sufficiently detailed to reflect the physical characteristics and constraints of the underlying flexible load, and includes the possibility of capturing diurnal and seasonal variations in the resource. Nonetheless, the model is of low complexity and thus suitable for inclusion in conventional unit commitment and market clearing algorithms. The ability to simulate DR as an operational resource on a power system over a year facilitates an assessment of its time-varying value to the power system.