National Library of Energy BETA

Sample records for methanol ethanol compressed

  1. Conversion of Methanol, Ethanol and Propanol over Zeolites

    SciTech Connect (OSTI)

    Ramasamy, Karthikeyan K.; Wang, Yong

    2013-06-04

    Renewable fuel from lignocellulosic biomass has recently attracted more attention due to its environmental and the potential economic benefits over the crude oil [1]. In particular the production of fuel range hydrocarbon (HC) from alcohol generated lots of interest since the alcohol can be produced from biomass via thermochemical [2] (mixed alcohol from gasification derived synthesis gas) as well as the biochemical routes [3] (alcohol fermentation). Along with the development of ZSM5 synthesis and the discovery of methanol-to-gasoline (MTG) process by Mobil in 1970’s triggered lots of interest in research and development arena to understand the reaction mechanisms of alcohols over zeolites in particular ZSM5 [4]. More detailed research on methanol conversion was extensively reported [5] and in recent times the research work can be found on ethanol [6] and other alcohols as well but comprehensive comparison of catalyst activity and the deactivation mechanism of the conversion of various alcohols over zeolites has not been reported. The experiments were conducted on smaller alcohols such as methanol, ethanol and 1-propanol over HZSM5. The experimental results on the catalyst activity and the catalyst deactivation mechanism will be discussed.

  2. Desorption Kinetics of Methanol, Ethanol, and Water from Graphene

    SciTech Connect (OSTI)

    Smith, R. Scott; Matthiesen, Jesper; Kay, Bruce D.

    2014-09-18

    The desorption kinetics of methanol, ethanol, and water from graphene covered Pt(111) are investigated. The temperature programmed desorption (TPD) spectra for both methanol and ethanol have well-resolved first, second, third, and multilayer layer desorption peaks. The alignment of the leading edges is consistent with zero-order desorption kinetics from all layers. In contrast, for water the first and second layers are not resolved. At low water coverages (< 1 ML) the initial desorption leading edges are aligned but then fall out of alignment at higher temperatures. For thicker water layers (10 to 100 ML), the desorption leading edges are in alignment throughout the desorption of the film. The coverage dependence of the desorption behavoir suggests that at low water coverages the non-alignment of the desorption leading edges is due to water dewetting from the graphene substrate. Kinetic simulations reveal that the experimental results are consistent with zero-order desorption. The simulations also show that fractional order desorption kinetics would be readily apparent in the experimental TPD spectra.

  3. Prediction of the Size Distributions of Methanol-Ethanol Clusters Detected in VUV Laser/Time-of-Flight Mass Spectrometry

    E-Print Network [OSTI]

    Goddard III, William A.

    Prediction of the Size Distributions of Methanol-Ethanol Clusters Detected in VUV Laser distributions and geometries of vapor clusters equilibrated with methanol-ethanol (Me-Et) liquid mixtures were distributions of vapor clusters equilibrated with liquids, ranging from neat alcohols1,2 to methanol-ethanol (Me

  4. THE JOURNAL OF CHEMICAL PHYSICS 142, 212408 (2015) Dynamics of water, methanol, and ethanol in a room temperature

    E-Print Network [OSTI]

    Fayer, Michael D.

    2015-01-01

    THE JOURNAL OF CHEMICAL PHYSICS 142, 212408 (2015) Dynamics of water, methanol, and ethanol with increasing alkyl chain length: water, methanol, and ethanol, diluted to low concentration in the room is increased: 23 ps for water, 28 ps for methanol, and 34 ps for ethanol. Although in each case, only a single

  5. Microbial Community Changes in Response to Ethanol or Methanol Amendments for U(VI) Reduction

    SciTech Connect (OSTI)

    Vishnivetskaya, Tatiana A [ORNL; Brandt, Craig C [ORNL; Madden, Andrew [University of Oklahoma, Norman; Drake, Meghan M [ORNL; Kostka, Joel [Florida State University; Akob, Denise M. [Florida State University; Kusel, Kirsten [Friedrich Schiller University Jena, Jena Germany; Palumbo, Anthony Vito [ORNL

    2010-01-01

    Microbial community responses to ethanol, methanol and methanol + humics amendments in relationship to uranium bioremediation were studied in laboratory microcosm experiments using sediments and ground water from a uranium-contaminated site in Oak Ridge, Tennessee. Ethanol addition always resulted in uranium reduction at rate of 0.8-1.0 mol l-1 d-1 while methanol addition did so occasionally at rate 0.95 mol l-1 d-1. The type of carbon source added, the duration of incubation, and the sampling site influenced the bacterial community structure upon incubation. Analysis of 16S rRNA gene clone libraries indicated (1) bacterial communities found in ethanol- and methanol-amended samples with U(VI) reduction were similar due to presence of -Proteobacteria, and -Proteobacteria (members of the families Burkholderiaceae, Comamonadaceae, Oxalobacteraceae, and Rhodocyclaceae); (2) methanol-amended samples without U(VI) reduction exhibited the lowest diversity and the bacterial community contained 69.2-92.8% of the family Methylophilaceae; and (3) the addition of humics resulted in an increase of phylogenetic diversity of -Proteobacteria (Rodoferax, Polaromonas, Janthinobacterium, Methylophilales, unclassified) and Firmicutes (Desulfosporosinus, Clostridium).

  6. Technoeconomic Comparison of Biofuels: Ethanol, Methanol, and Gasoline from Gasification of Woody Residues (Presentation)

    SciTech Connect (OSTI)

    Tarud, J.; Phillips, S.

    2011-08-01

    This presentation provides a technoeconomic comparison of three biofuels - ethanol, methanol, and gasoline - produced by gasification of woody biomass residues. The presentation includes a brief discussion of the three fuels evaluated; discussion of equivalent feedstock and front end processes; discussion of back end processes for each fuel; process comparisons of efficiencies, yields, and water usage; and economic assumptions and results, including a plant gate price (PGP) for each fuel.

  7. A comparative experimental and computational study of methanol, ethanol, and n-butanol flames

    SciTech Connect (OSTI)

    Veloo, Peter S.; Wang, Yang L.; Egolfopoulos, Fokion N.; Westbrook, Charles K.

    2010-10-15

    Laminar flame speeds and extinction strain rates of premixed methanol, ethanol, and n-butanol flames were determined experimentally in the counterflow configuration at atmospheric pressure and elevated unburned mixture temperatures. Additional measurements were conducted also to determine the laminar flame speeds of their n-alkane/air counterparts, namely methane, ethane, and n-butane in order to compare the effect of alkane and alcohol molecular structures on high-temperature flame kinetics. For both propagation and extinction experiments the flow velocities were determined using the digital particle image velocimetry method. Laminar flame speeds were derived through a non-linear extrapolation approach based on direct numerical simulations of the experiments. Two recently developed detailed kinetics models of n-butanol oxidation were used to simulate the experiments. The experimental results revealed that laminar flame speeds of ethanol/air and n-butanol/air flames are similar to those of their n-alkane/air counterparts, and that methane/air flames have consistently lower laminar flame speeds than methanol/air flames. The laminar flame speeds of methanol/air flames are considerably higher compared to both ethanol/air and n-butanol/air flames under fuel-rich conditions. Numerical simulations of n-butanol/air freely propagating flames, revealed discrepancies between the two kinetic models regarding the consumption pathways of n-butanol and its intermediates. (author)

  8. Improvement of performance and emissions of a compression ignition methanol engine with dimethyl ether

    SciTech Connect (OSTI)

    Guo, J.; Chikahisa, Takemi; Murayama, Tadashi; Miyano, Masaharu

    1994-10-01

    Dimethyl ether (DME) has very good compression ignition characteristics and can be converted from methanol using a {gamma}-alumina catalyst. In this study a torch ignition chamber (TIC) head with TIC close to the center of the main combustion chamber was designed for the TIC method. The possibility of improvements in reducing the quantities of DME and emission were investigated by optimizing the TIC position, methanol injection timing, DME injection timing, and intake and exhaust throttling. It was found that the necessary amount of DME was greatly reduced when optimizing methanol and DME injection timings. 2 refs., 16 figs., 1 tab.

  9. Mixing it up - Measuring diffusion in supercooled liquid solutions of methanol and ethanol at temperatures near the glass transition

    SciTech Connect (OSTI)

    Matthiesen, Jesper; Smith, R. Scott; Kay, Bruce D.

    2011-03-17

    Do liquid mixtures, cooled to temperatures below their freezing point, behave as normal liquids? We address this question using nanoscale films of methanol and ethanol supercooled liquid solutions of varying composition (7 -93% methanol) at temperatures near their glass transition,Tg. The permeation of Kr through these films is used to determine the diffusivities of the supercooled liquid mixtures. We find that the temperature dependent diffusivities of the mixtures are well-fit by a Vogel-Fulcher-Tamman equation indicating that the mixtures exhibit fragile behavior at temperatures just above their Tg. Further, for a given temperature, the composition dependent diffusivity is well-fit by a Vignes-type equation, i.e. the diffusivity of any mixture can be predicted using an exponential weighting of the diffusion of the pure methanol and ethanol diffusivities. These results show that deeply supercooled liquid mixtures can be used to provide valuable insight into the properties of normal liquid mixtures.

  10. Methanol with dimethyl ether ignition promotor as fuel for compression ignition engines

    SciTech Connect (OSTI)

    Brook, D.L.; Cipolat, D.; Rallis, C.J.

    1984-08-01

    Reduction of the world dependence upon crude oil necessitates the use of long term alternative fuels for internal combustion engines. Alcohols appear to offer a solution as in the short term they can be manufactured from natural gas and coal, while ultimately they may be produced from agricultural products. A fair measure of success has been achieved in using alcohols in spark ignition engines. However the more widely used compression ignition engines cannot utilize unmodified pure alcohols. The current techniques for using alcohol fuels in compression ignition engines all have a number of shortcomings. This paper describes a novel technique where an ignition promotor, dimethyl ether (DME), is used to increase the cetane rating of methanol. The systems particular advantage is that the DME can be catalyzed from the methanol base fuel, in situ. This fuel system matches the performance characteristics of diesel oil fuel.

  11. Methanol/ethanol/gasoline blend-fuels demonstration with stratified-charge-engine vehicles: Consultant report. Final report

    SciTech Connect (OSTI)

    Pefley, R.; Adelman, H.; Suga, T.

    1980-03-01

    Four 1978 Honda CVCC vehicles have been in regular use by California Energy Commission staff in Sacramento for 12 months. Three of the unmodified vehicles were fueled with alcohol/gasoline blends (5% methanol, 10% methanol, and 10% ethanol) with the fourth remaining on gasoline as a control. The operators did not know which fuels were in the vehicles. At 90-day intervals the cars were returned to the Univerity of Santa Clara for servicing and for emissions and fuel economy testing in accordance with the Federal Test Procedures. The demonstration and testing have established the following: (1) the tested blends cause no significant degradation in exhaust emissions, fuel economy, and driveability; (2) the tested blends cause significant increases in evaporative emissions; (3) analysis of periodic oil samples shows no evidence of accelerated metal wear; and (4) higher than 10% alcohols will require substantial modification to most existing California motor vehicles for acceptable emissions, performance, and fuel economy. Many aspects of using methanol and ethanol fuels, both straight and in blends, in various engine technologies are discussed.

  12. Direct Use of Wet Ethanol in a Homogeneous Charge Compression Ignition (HCCI) Engine: Experimental and Numerical Results

    E-Print Network [OSTI]

    Mack, John Hunter; Flowers, Daniel L; Aceves, Salvador M; Dibble, Robert W

    2007-01-01

    The energy balance of corn ethanol revisited, Transaction offor autoignition. The wet ethanol modeling study [REF] usedengine running on wet ethanol. Fuel mixtures studied range

  13. Characterization of Dual-Fuel Reactivity Controlled Compression Ignition (RCCI) Using Hydrated Ethanol and Diesel Fuel

    Broader source: Energy.gov [DOE]

    This study uses numerical simulations to explore the use of wet ethanol as the low-reactivity fuel and diesel as the high-reactivity fuel for RCCI operation in a heavy-duty diesel engine.

  14. Process for producing ethanol from syngas

    DOE Patents [OSTI]

    Krause, Theodore R; Rathke, Jerome W; Chen, Michael J

    2013-05-14

    The invention provides a method for producing ethanol, the method comprising establishing an atmosphere containing methanol forming catalyst and ethanol forming catalyst; injecting syngas into the atmosphere at a temperature and for a time sufficient to produce methanol; and contacting the produced methanol with additional syngas at a temperature and for a time sufficient to produce ethanol. The invention also provides an integrated system for producing methanol and ethanol from syngas, the system comprising an atmosphere isolated from the ambient environment; a first catalyst to produce methanol from syngas wherein the first catalyst resides in the atmosphere; a second catalyst to product ethanol from methanol and syngas, wherein the second catalyst resides in the atmosphere; a conduit for introducing syngas to the atmosphere; and a device for removing ethanol from the atmosphere. The exothermicity of the method and system obviates the need for input of additional heat from outside the atmosphere.

  15. Methanol production method and system

    DOE Patents [OSTI]

    Chen, Michael J. (Darien, IL); Rathke, Jerome W. (Bolingbrook, IL)

    1984-01-01

    Ethanol is selectively produced from the reaction of methanol with carbon monoxide and hydrogen in the presence of a transition metal carbonyl catalyst. Methanol serves as a solvent and may be accompanied by a less volatile co-solvent. The solution includes the transition metal carbonyl catalysts and a basic metal salt such as an alkali metal or alkaline earth metal formate, carbonate or bicarbonate. A gas containing a high carbon monoxide to hydrogen ratio, as is present in a typical gasifer product, is contacted with the solution for the preferential production of ethanol with minimal water as a byproduct. Fractionation of the reaction solution provides substantially pure ethanol product and allows return of the catalysts for reuse.

  16. Characterization of Dual-Fuel Reactivity Controlled Compression...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dual-Fuel Reactivity Controlled Compression Ignition (RCCI) Using Hydrated Ethanol and Diesel Fuel Characterization of Dual-Fuel Reactivity Controlled Compression Ignition (RCCI)...

  17. Method for making methanol

    DOE Patents [OSTI]

    Mednick, R. Lawrence (Roslyn Heights, NY); Blum, David B. (Wayne, NJ)

    1986-01-01

    Methanol is made in a liquid-phase methanol reactor by entraining a methanol-forming catalyst in an inert liquid and contacting said entrained catalyst with a synthesis gas comprising hydrogen and carbon monoxide.

  18. Method for making methanol

    DOE Patents [OSTI]

    Mednick, R. Lawrence (Roslyn Heights, NY); Blum, David B. (Wayne, NJ)

    1987-01-01

    Methanol is made in a liquid-phase methanol reactor by entraining a methanol-forming catalyst in an inert liquid and contacting said entrained catalyst with a synthesis gas comprising hydrogen and carbon monoxide.

  19. Ethanol production method and system

    DOE Patents [OSTI]

    Chen, M.J.; Rathke, J.W.

    1983-05-26

    Ethanol is selectively produced from the reaction of methanol with carbon monoxide and hydrogen in the presence of a transition metal carbonyl catalyst. Methanol serves as a solvent and may be accompanied by a less volatile co-solvent. The solution includes the transition metal carbonyl catalysts and a basic metal salt such as an alkali metal or alkaline earth metal formate, carbonate or bicarbonate. A gas containing a high carbon monoxide to hydrogen ratio, as is present in a typical gasifer product, is contacted with the solution for the preferential production of ethanol with minimal water as a byproduct. Fractionation of the reaction solution provides substantially pure ethanol product and allows return of the catalysts for reuse.

  20. Method and system for ethanol production

    DOE Patents [OSTI]

    Feder, H.M.; Chen, M.J.

    1980-05-21

    A transition metal carbonyl and a tertiary amine are employed as a homogeneous catalytic system in methanol or a less volatile solvent to react methanol with carbon monoxide and hydrogen gas producing ethanol and carbon dioxide. The gas contains a high carbon monoxide to hydrogen ratio as is present in a typical gasifier product. The reaction has potential for anhydrous ethanol production as carbon dioxide rather than water is produced. The only other significant by-product is methane. Selected transition metal carbonyls include those of iron, ruthenium and possibly manganese and osmium. Selected amines include trimethylamine, N-Methylpyrrolidine, 24-diazabicyclooctane, dimethyneopentylamine and 2-pryidinol.

  1. Method and system for ethanol production

    DOE Patents [OSTI]

    Feder, Harold M. (Darien, IL); Chen, Michael J. (Darien, IL)

    1981-01-01

    A transition metal carbonyl and a tertiary amine are employed as a homogeneous catalytic system in methanol or a less volatile solvent to react methanol with carbon monoxide and hydrogen gas producing ethanol and carbon dioxide. The gas contains a high carbon monoxide to hydrogen ratio as is present in a typical gasifier product. The reaction has potential for anhydrous ethanol production as carbon dioxide rather than water is produced. The only other significant by product is methane. Selected transition metal carbonyls include those of iron, ruthenium and possibly manganese and osmium. Selected amines include trimethylamine, N-Methylpyrrolidine, 24-diazabicyclooctane, dimethyneopentylamine and 2-pryidinol.

  2. Method and system for ethanol production

    DOE Patents [OSTI]

    Feder, Harold M. (Darien, IL); Chen, Michael J. (Darien, IL)

    1983-01-01

    A transition metal carbonyl and a tertiary amine are employed as a homogeneous catalytic system in methanol or a less volatile solvent to react methanol with carbon monoxide and hydrogen gas producing ethanol and carbon dioxide. The gas contains a high carbon monoxide to hydrogen ratio as is present in a typical gasifier product. The reaction has potential for anhydrous ethanol production as carbon dioxide rather than water is produced. Selected transition metal carbonyls include those of iron, rhodium ruthenium, manganese in combination with iron and possibly osmium. Selected amines include trimethylamine, N-Methylpyrrolidine, 2,4-diazabicyclooctane, dimethylneopentylamine, N-methylpiperidine and derivatives of N-methylpiperidine.

  3. Method and system for ethanol production

    DOE Patents [OSTI]

    Feder, H.M.; Chen, M.J.

    1981-09-24

    A transition metal carbonyl and a tertiary amine are employed as a homogeneous catalytic system in methanol or a less volatile solvent to react methanol with carbon monoxide and hydrogen gas producing ethanol and carbon dioxide. The gas contains a high carbon monoxide to hydrogen ratio as is present in a typical gasifier product. The reaction has potential for anhydrous ethanol production as carbon dioxide rather than water is produced. Selected transition metal carbonyls include those of iron, rhodium, ruthenium, manganese in combination with iron and possibly osmium. Selected amines include trimethylamine, N-Methylpyrrolidine, 2,4-diazabicyclooctane, dimethylneopentylamine, N-methylpiperidine and derivatives of N-methylpiperidine.

  4. Natural Gas Ethanol Flex-Fuel

    E-Print Network [OSTI]

    Natural Gas Propane Electric Ethanol Flex-Fuel Biodiesel Vehicle Buyer's Guide Clean Cities 2012 . . . . . . . . . . . . . . . . . . . . . . . . 4 About This Guide . . . . . . . . . . . . . . . . . . . 5 Compressed Natural Gas and emissions. Alternative fueling infrastructure is expanding in many regions, making natural gas, propane

  5. Heavy Alcohols as a Fuel Blending Agent for Compression Ignition...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Downsized SI Engines Using Alcohol DI for Knock Avoidance Characterization of Dual-Fuel Reactivity Controlled Compression Ignition (RCCI) Using Hydrated Ethanol and...

  6. Methanol partial oxidation reformer

    DOE Patents [OSTI]

    Ahmed, Shabbir (Bolingbrook, IL); Kumar, Romesh (Naperville, IL); Krumpelt, Michael (Naperville, IL)

    1999-01-01

    A partial oxidation reformer comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell.

  7. Methanol partial oxidation reformer

    DOE Patents [OSTI]

    Ahmed, Shabbir (Bolingbrook, IL); Kumar, Romesh (Naperville, IL); Krumpelt, Michael (Naperville, IL)

    2001-01-01

    A partial oxidation reformer comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell.

  8. Methanol adsorption on graphene

    E-Print Network [OSTI]

    Schroder, Elsebeth

    2013-01-01

    The adsorption energies and orientation of methanol on graphene are determined from first-principles density functional calculations. We employ the well-tested vdW-DF method that seamlessly includes dispersion interactions with all of the more close-ranged interactions that result in bonds like the covalent and hydrogen bonds. The adsorption of a single methanol molecule and small methanol clusters on graphene are studied at various coverages. Adsorption in clusters or at high coverages (less than a monolayer) is found to be preferable, with the methanol C-O axis approximately parallel to the plane of graphene. The adsorption energies calculated with vdW-DF are compared with previous DFT-D and MP2-based calculations for single methanol adsorption on flakes of graphene (polycyclic aromatic hydrocarbons). For the high coverage adsorption energies we also find reasonably good agreement with previous desorption measurements.

  9. Methanol partial oxidation reformer

    DOE Patents [OSTI]

    Ahmed, S.; Kumar, R.; Krumpelt, M.

    1999-08-24

    A partial oxidation reformer is described comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell. 7 figs.

  10. Methanol partial oxidation reformer

    DOE Patents [OSTI]

    Ahmed, S.; Kumar, R.; Krumpelt, M.

    1999-08-17

    A partial oxidation reformer is described comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell. 7 figs.

  11. THE FURNACE COMBUSTION AND RADIATION CHARACTERISTICS OF METHANOL AND A METHANOL/COAL SLURRY

    E-Print Network [OSTI]

    Grosshandler, W.L.

    2010-01-01

    vol. ) in Methanol Furnace , 2 , . . . . . . . . , . , .Velocity Profiles in Methanol Furnace Temperature Profiles:to Pure Methanol . . . . . . . . . . . . , . . . . C02

  12. Vacuum-Ultraviolet (VUV) Photoionization of Small Methanol and Methanol-Water Clusters

    E-Print Network [OSTI]

    Kostko, Oleg

    2008-01-01

    methanol and methanol-water clusters evaluated frommethanol molecules and a water monomer connected via threeof small methanol and methanol-water clusters Oleg Kostko,

  13. Combustion characteristics of indolene-methanol blends in a CFR spark ignition engine

    SciTech Connect (OSTI)

    Patel, K.S.

    1984-01-01

    A study of the combustion characteristics of indolene, methanol and indolene-methanol blends has been completed. The investigation included theoretical and experimental parts. In the theoretical part, turbulent burning velocity, laminar burning velocity, and mass burning velocity are computed. The experimental part was completed on a CFR spark ignition engine using indolene, methanol, and indolene-methanol blends. Methanol concentration was varied from 0 to 100 vol.%. For each blend, compression ratio was varied from 5.0 to KLCR (Knock Limited Compression Ratio). The results of theoretical analysis showed that the laminar burning velocity increased as the vol.% of methanol increased. The experimental results indicated that adding methanol to indolene, MBT (Minimum advanced for Best Torque) spark advance, volumetric efficiency, brake mean effective pressure are decreased while break specific fuel consumption, brake thermal efficiency an KLCR are increased. The theoretical and experimental results showed that adding methanol to indolene, apparent flame speed, turbulent burning velocity and the ratio of turbulent to laminar burning velocity increased. Pure methanol produced the highest turbulent burning velocity. It is concluded that methanol has considerable effect on the combustion characteristics of spark ignition engine.

  14. DOI: 10.1002/chem.200700579 Selective Catalytic Oxidation of Ethanol to Acetic Acid on Dispersed

    E-Print Network [OSTI]

    Iglesia, Enrique

    DOI: 10.1002/chem.200700579 Selective Catalytic Oxidation of Ethanol to Acetic Acid on Dispersed Mo, such as acetaldehyde and acetic acid, currently produced from ethane, ethene, or methanol. Pd-based catalysts convert ethanol­O2 reactants to acetic acid, but with low reaction rates and modest selectivities (433 K, 70

  15. Advances in Energy Reduction in Methanol Plant Design 

    E-Print Network [OSTI]

    Huggins, P. J.; Griffiths, G. W.

    1982-01-01

    Waste heat in the flue gas from the refOrmi~g furnace is recovered by raising and superhe ting steam and for preheating combustion air use by the reforming furnace burners. ' Similarly waste heat in the synthesis gas, lhiCh is suitable for methane... synthesis without f rther process i ng, is recovered by ra ising steam, re heating boiler feedwater and preheating dea rator feedwater. j i Compression: After final cooling the ~ynthesis gas is compressed in a centrifugal compress~r to the methanol...

  16. List of Methanol Incentives | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsource History ViewInformationWindsCompressed airGeothermalList of Methanol

  17. 4, 125164, 2007 Methanol exchange

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    BGD 4, 125­164, 2007 Methanol exchange between grassland and the atmosphere A. Brunner et al. Title Discussions Biogeosciences Discussions is the access reviewed discussion forum of Biogeosciences Methanol (albrecht.neftel@art.admin.ch) 125 #12;BGD 4, 125­164, 2007 Methanol exchange between grassland

  18. The Development of Methanol Industry and Methanol Fuel in China

    SciTech Connect (OSTI)

    Li, W.Y.; Li, Z.; Xie, K.C.

    2009-07-01

    In 2007, China firmly established itself as the driver of the global methanol industry. The country became the world's largest methanol producer and consumer. The development of the methanol industry and methanol fuel in China is reviewed in this article. China is rich in coal but is short on oil and natural gas; unfortunately, transportation development will need more and more oil to provide the fuel. Methanol is becoming a dominant alternative fuel. China is showing the rest of the world how cleaner transportation fuels can be made from coal.

  19. Intercooling effects of methanol on turbocharged diesel engine performance and exhaust emissions

    SciTech Connect (OSTI)

    Saito, T.; Daisho, Y.; Aoki, Y.; Kawase, N.

    1984-01-01

    From the viewpoint of utilizing methanol fuel in an automotive turbocharged direct-injection diesel engine, an intercooling system supplying liquid methanol has been devised and its effects on engine performance and exhaust gas emissions have been investigated. With an electronically controlled injector in this system, methanol as a supplementary fuel to diesel fuel can be injected into the intake pipe in order to intercool a hot air charge compressed by the turbocharger. It has been confirmed that especially at heavy load conditions, methanol-intercooling can yield a higher thermal efficiency, and lower nox and smoke emissions simultaneously, compared with three other cases without using methanol: natural aspiration and the cases with and without an ordinary intercooler. However, methanol fueling must be avoided at lower loads since sacrifices in efficiency and hydrocarbon emissions are involved.

  20. Desorption Kinetics of Methanol, Ethanol, and Water from Graphene (Journal

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefieldSulfate Reducing BacteriaConnectlaser-solid interactionCrystalDesigning aDesigns for a

  1. Improved Flow-Field Structures for Direct Methanol Fuel Cells

    SciTech Connect (OSTI)

    Gurau, Bogdan

    2013-05-31

    The direct methanol fuel cell (DMFC) is ideal if high energy-density liquid fuels are required. Liquid fuels have advantages over compressed hydrogen including higher energy density and ease of handling. Although state-of-the-art DMFCs exhibit manageable degradation rates, excessive fuel crossover diminishes system energy and power density. Although use of dilute methanol mitigates crossover, the concomitant lowering of the gross fuel energy density (GFED) demands a complex balance-of-plant (BOP) that includes higher flow rates, external exhaust recirculation, etc. An alternative approach is redesign of the fuel delivery system to accommodate concentrated methanol. NuVant Systems Inc. (NuVant) will maximize the GFED by design and assembly of a DMFC that uses near neat methanol. The approach is to tune the diffusion of highly concentrated methanol (to the anode catalytic layer) to the back-diffusion of water formed at the cathode (i.e. in situ generation of dilute methanol at the anode layer). Crossover will be minimized without compromising the GFED by innovative integration of the anode flow-field and the diffusion layer. The integrated flow-field-diffusion-layers (IFDLs) will widen the current and potential DMFC operating ranges and enable the use of cathodes optimized for hydrogen-air fuel cells.

  2. Methanol production with elemental phosphorus byproduct gas: technical and economic feasibility

    SciTech Connect (OSTI)

    Lyke, S.E.; Moore, R.H.

    1981-01-01

    The technical and economic feasibility of using a typical, elemental, phosphorus byproduct gas stream in methanol production is assessed. The purpose of the study is to explore the potential of a substitute for natural gas. The first part of the study establishes economic tradeoffs between several alternative methods of supplying the hydrogen which is needed in the methanol synthesis process to react with CO from the off gas. The preferred alternative is the Battelle Process, which uses natural gas in combination with the off gas in an economically sized methanol plant. The second part of the study presents a preliminary basic design of a plant to (1) clean and compress the off gas, (2) return recovered phosphorus to the phosphorus plant, and (3) produce methanol by the Battelle Process. Use of elemental phosphorus byproduct gas in methanol production appears to be technically feasible. The Battelle Process shows a definite but relatively small economic advantage over conventional methanol manufacture based on natural gas alone. The process would be economically feasible only where natural gas supply and methanol market conditions at a phosphorus plant are not significantly less favorable than at competing methanol plants. If off-gas streams from two or more phosphorus plants could be combined, production of methanol using only offgas might also be economically feasible. The North American methanol market, however, does not seem likely to require another new methanol project until after 1990. The off-gas cleanup, compression, and phosphorus-recovery system could be used to produce a CO-rich stream that could be economically attractive for production of several other chemicals besides methanol.

  3. Compressed Postscript

    E-Print Network [OSTI]

    camshape, methanol, polygon, and rocket. Also, many minor iterations were required. on catmix, elec, and robot with SNOPT as its subproblem solver.

  4. Vacuum-Ultraviolet (VUV) Photoionization of Small Methanol and Methanol-Water Clusters

    E-Print Network [OSTI]

    Kostko, Oleg

    2008-01-01

    Table 1 Appearance energies for pure and protonated methanoland methanol-water clusters evaluated from photoionizationVUV) photoionization of small methanol and methanol-water

  5. Vacuum-ultraviolet (VUV) photoionization of small methanol and methanol-water clusters

    E-Print Network [OSTI]

    Ahmed, Musahid

    2008-01-01

    methanol molecules and a water monomer connected via threemethanol and methanol-water clusters evaluated frommethanol and methanol-water clusters Journal: Manuscript ID:

  6. The Methanol Economy Project

    SciTech Connect (OSTI)

    Olah, George; Prakash, G.K.

    2013-12-31

    The Methanol Economy Project is based on the concept of replacing fossil fuels with methanol generated either from renewable resources or abundant natural (shale) gas. The full methanol cycle was investigated in this project, from production of methanol through bromination of methane, bireforming of methane to syngas, CO{sub 2} capture using supported amines, co-electrolysis of CO{sub 2} and water to formate and syngas, decomposition of formate to CO{sub 2} and H{sub 2}, and use of formic acid in a direct formic acid fuel cell. Each of these projects achieved milestones and provided new insights into their respective fields. ? Direct electrophilic bromination of methane to methyl bromide followed by hydrolysis to yield methanol was investigated on a wide variety of catalyst systems, but hydrolysis proved impractical for large-scale industrial application. ? Bireforming the correct ratio of methane, CO{sub 2}, and water on a NiO / MgO catalyst yielded the right proportion of H{sub 2}:CO (2:1) and proved to be stable for at least 250 hours of operation at 400 psi (28 atm). ? CO{sub 2} capture utilizing supported polyethyleneimines yielded a system capable of adsorbing CO{sub 2} from the air and release at nominal temperatures with negligible amine leaching. ? CO{sub 2} electrolysis to formate and syngas showed considerable increases in rate and selectivity by performing the reaction in a high pressure flow electrolyzer. ? Formic acid was shown to decompose selectively to CO{sub 2} and H{sub 2} using either Ru or Ir based homogeneous catalysts. ? Direct formic acid fuel cells were also investigated and showed higher than 40% voltage efficiency using reduced loadings of precious metals. A technoeconomic analysis was conducted to assess the viability of taking each of these processes to the industrial scale by applying the data gathered during the experiments to approximations based on currently used industrial processes. Several of these processes show significant promise for industrial scale up and use towards improving our nation’s energy independence.

  7. Societal lifetime cost of hydrogen fuel cell vehicles

    E-Print Network [OSTI]

    Sun, Yongling; Ogden, J; Delucchi, Mark

    2010-01-01

    Compressed Natural Gas (CNG), synthetic diesel, methanol,FCX Fuels Gasoline, Diesel, CNG, FT diesel, methanol, H2,H2, electricity Gasoline, diesel, CNG, biogas, LPG, ethanol,

  8. Methanol | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo, Maryland: Energy ResourcesDec 2005 WindPRO is developed by EMDPower Inc Jump to:Methanol

  9. High compression ratio turbo gasoline engine operation using alcohol enhancement

    E-Print Network [OSTI]

    Lewis, Raymond (Raymond A.)

    2013-01-01

    Gasoline - ethanol blends were explored as a strategy to mitigate engine knock, a phenomena in spark ignition engine combustion when a portion of the end gas is compressed to the point of spontaneous auto-ignition. This ...

  10. Ethanol Basics (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2015-01-01

    Ethanol is a widely-used, domestically-produced renewable fuel made from corn and other plant materials. More than 96% of gasoline sold in the United States contains ethanol. Learn more about this alternative fuel in the Ethanol Basics Fact Sheet, produced by the U.S. Department of Energy's Clean Cities program.

  11. amine methanol, ether . Amine amine CO2

    E-Print Network [OSTI]

    Hong, Deog Ki

    IP [2012] 7 C O 2 (CO2) . CO2 amine methanol, ether . Amine amine CO2 CO2 .Amine CO2 (functional group) amine amine+ +promoter .Amine CO2 CO2 . . , methanol ether methanol, ether promoter CO2 CO2 H2S, COS CO2 . Methanol rectisol process, di-methylene ether polypropylene glycol selexol (-30oC) . CO2

  12. Deactivation of methanol synthesis catalysts

    SciTech Connect (OSTI)

    Roberts, G.W.; Brown, D.M.; Hsiung, T.H.; Lewnard, J.J. (Air Products and Chemicals, Inc., Allentown, PA (United States))

    1993-08-01

    A novel methanol synthesis process, the liquid-phase methanol (LPMEOH) process, has been developed and scaled up to a nominal 380 kg/h (10 ton/day) pilot plant. The process is based on a gas-sparged slurry reactor instead of a conventional, fixed-bed reactor. The use of slurry reactors, which are essentially gradientless, greatly facilitated the interpretation and quantification of catalyst deactivation phenomena. With a poison-free, CO-rich feedstream, the rate of deactivation of the Cu/ZnO catalyst increased rapidly with temperature. At constant temperature, in the absence of poisons, the decline with time in the rate constant for methanol synthesis correlated with the loss of BET surface area. Iron carbonyl, nickel carbonyl, and carbonyl sulfide are severe and highly specific poisons for methanol-synthesis catalyst. There was a linear relationship between the catalyst activity loss and the concentration of metal or sulfur on the catalyst.

  13. Analysis of Mass Transport of Methanol at the Anode of a Direct Methanol Fuel Cell

    E-Print Network [OSTI]

    Zhao, Tianshou

    Analysis of Mass Transport of Methanol at the Anode of a Direct Methanol Fuel Cell C. Xu,a Y. L. He transport of methanol at the anode of a direct methanol fuel cell DMFC and show that the overall mass current density of an in-house-fabricated DMFC with different flow fields for various methanol

  14. Compression embedding

    DOE Patents [OSTI]

    Sandford, M.T. II; Handel, T.G.; Bradley, J.N.

    1998-07-07

    A method and apparatus for embedding auxiliary information into the digital representation of host data created by a lossy compression technique and a method and apparatus for constructing auxiliary data from the correspondence between values in a digital key-pair table with integer index values existing in a representation of host data created by a lossy compression technique are disclosed. The methods apply to data compressed with algorithms based on series expansion, quantization to a finite number of symbols, and entropy coding. Lossy compression methods represent the original data as ordered sequences of blocks containing integer indices having redundancy and uncertainty of value by one unit, allowing indices which are adjacent in value to be manipulated to encode auxiliary data. Also included is a method to improve the efficiency of lossy compression algorithms by embedding white noise into the integer indices. Lossy compression methods use loss-less compression to reduce to the final size the intermediate representation as indices. The efficiency of the loss-less compression, known also as entropy coding compression, is increased by manipulating the indices at the intermediate stage. Manipulation of the intermediate representation improves lossy compression performance by 1 to 10%. 21 figs.

  15. Compression embedding

    DOE Patents [OSTI]

    Sandford, II, Maxwell T. (Los Alamos, NM); Handel, Theodore G. (Los Alamos, NM); Bradley, Jonathan N. (Los Alamos, NM)

    1998-01-01

    A method and apparatus for embedding auxiliary information into the digital representation of host data created by a lossy compression technique and a method and apparatus for constructing auxiliary data from the correspondence between values in a digital key-pair table with integer index values existing in a representation of host data created by a lossy compression technique. The methods apply to data compressed with algorithms based on series expansion, quantization to a finite number of symbols, and entropy coding. Lossy compression methods represent the original data as ordered sequences of blocks containing integer indices having redundancy and uncertainty of value by one unit, allowing indices which are adjacent in value to be manipulated to encode auxiliary data. Also included is a method to improve the efficiency of lossy compression algorithms by embedding white noise into the integer indices. Lossy compression methods use loss-less compression to reduce to the final size the intermediate representation as indices. The efficiency of the loss-less compression, known also as entropy coding compression, is increased by manipulating the indices at the intermediate stage. Manipulation of the intermediate representation improves lossy compression performance by 1 to 10%.

  16. Compression embedding

    DOE Patents [OSTI]

    Sandford, M.T. II; Handel, T.G.; Bradley, J.N.

    1998-03-10

    A method of embedding auxiliary information into the digital representation of host data created by a lossy compression technique is disclosed. The method applies to data compressed with lossy algorithms based on series expansion, quantization to a finite number of symbols, and entropy coding. Lossy compression methods represent the original data as integer indices having redundancy and uncertainty in value by one unit. Indices which are adjacent in value are manipulated to encode auxiliary data. By a substantially reverse process, the embedded auxiliary data can be retrieved easily by an authorized user. Lossy compression methods use loss-less compressions known also as entropy coding, to reduce to the final size the intermediate representation as indices. The efficiency of the compression entropy coding, known also as entropy coding is increased by manipulating the indices at the intermediate stage in the manner taught by the method. 11 figs.

  17. Compression embedding

    DOE Patents [OSTI]

    Sandford, II, Maxwell T. (Los Alamos, NM); Handel, Theodore G. (Los Alamos, NM); Bradley, Jonathan N. (Los Alamos, NM)

    1998-01-01

    A method of embedding auxiliary information into the digital representation of host data created by a lossy compression technique. The method applies to data compressed with lossy algorithms based on series expansion, quantization to a finite number of symbols, and entropy coding. Lossy compression methods represent the original data as integer indices having redundancy and uncertainty in value by one unit. Indices which are adjacent in value are manipulated to encode auxiliary data. By a substantially reverse process, the embedded auxiliary data can be retrieved easily by an authorized user. Lossy compression methods use loss-less compressions known also as entropy coding, to reduce to the final size the intermediate representation as indices. The efficiency of the compression entropy coding, known also as entropy coding is increased by manipulating the indices at the intermediate stage in the manner taught by the method.

  18. THE FURNACE COMBUSTION AND RADIATION CHARACTERISTICS OF METHANOL AND A METHANOL/COAL SLURRY

    E-Print Network [OSTI]

    Grosshandler, W.L.

    2010-01-01

    Spectral Intensity With 5% Coal (x ::: 86.9 cm) CalculatedPredictions B. Methanol/Coal Slurry as the Fuel TemperatureMethanol as the Fuel B. Methanol/Coal Slurry as the Fuel C.

  19. Fermentation method producing ethanol

    DOE Patents [OSTI]

    Wang, Daniel I. C. (Belmont, MA); Dalal, Rajen (Chicago, IL)

    1986-01-01

    Ethanol is the major end product of an anaerobic, thermophilic fermentation process using a mutant strain of bacterium Clostridium thermosaccharolyticum. This organism is capable of converting hexose and pentose carbohydrates to ethanol, acetic and lactic acids. Mutants of Clostridium thermosaccharolyticum are capable of converting these substrates to ethanol in exceptionally high yield and with increased productivity. Both the mutant organism and the technique for its isolation are provided.

  20. Rapid starting methanol reactor system

    DOE Patents [OSTI]

    Chludzinski, Paul J. (38 Berkshire St., Swampscott, MA 01907); Dantowitz, Philip (39 Nancy Ave., Peabody, MA 01960); McElroy, James F. (12 Old Cart Rd., Hamilton, MA 01936)

    1984-01-01

    The invention relates to a methanol-to-hydrogen cracking reactor for use with a fuel cell vehicular power plant. The system is particularly designed for rapid start-up of the catalytic methanol cracking reactor after an extended shut-down period, i.e., after the vehicular fuel cell power plant has been inoperative overnight. Rapid system start-up is accomplished by a combination of direct and indirect heating of the cracking catalyst. Initially, liquid methanol is burned with a stoichiometric or slightly lean air mixture in the combustion chamber of the reactor assembly. The hot combustion gas travels down a flue gas chamber in heat exchange relationship with the catalytic cracking chamber transferring heat across the catalyst chamber wall to heat the catalyst indirectly. The combustion gas is then diverted back through the catalyst bed to heat the catalyst pellets directly. When the cracking reactor temperature reaches operating temperature, methanol combustion is stopped and a hot gas valve is switched to route the flue gas overboard, with methanol being fed directly to the catalytic cracking reactor. Thereafter, the burner operates on excess hydrogen from the fuel cells.

  1. THE FURNACE COMBUSTION AND RADIATION CHARACTERISTICS OF METHANOL AND A METHANOL/COAL SLURRY

    E-Print Network [OSTI]

    Grosshandler, W.L.

    2010-01-01

    vol. ) in IVlethano'J Furnace II 1-2. III-3. III-4. III-5.vol. ) in Methanol Furnace , 2 , . . . . . . . . , . , .Velocity Profiles in Methanol Furnace Temperature Profiles:

  2. Vacuum-ultraviolet (VUV) photoionization of small methanol and methanol-water clusters

    E-Print Network [OSTI]

    Ahmed, Musahid

    2008-01-01

    cyclic trimer containing two methanol molecules and a waterTable 1 Appearance energies for pure and protonated methanoland methanol-water clusters evaluated from photoionization

  3. Methanol detection in M82

    E-Print Network [OSTI]

    S. Martín; J. Martín-Pintado; R. Mauersberger

    2006-03-07

    We present a multilevel study of the emission of methanol, detected for the first time in this galaxy, and discuss the origin of its emission. The high observed methanol abundance of a few 10^-9 can only be explained if injection of methanol from dust grains is taken into account. While the overall [CH3OH]/[NH3] ratio is much larger than observed towards other starbursts, the dense high excitation component shows a similar value to that found in NGC 253 and Maffei 2. Our observations suggest the molecular material in M 82 to be formed by dense warm cores, shielded from the UV radiation and similar to the molecular clouds in other starbursts, surrounded by a less dense photodissociated halo. The dense warm cores are likely the location of recent and future star formation within M 82.

  4. Distances to Galactic methanol masers

    E-Print Network [OSTI]

    K. L. J. Rygl; A. Brunthaler; K. M. Menten; M. J. Reid; H. J. van Langevelde

    2008-12-09

    We present the first EVN parallax measurements of 6.7 GHz methanol masers in star forming regions of the Galaxy. The 6.7 GHz methanol maser transition is a very valuable astrometric tool, for its large stability and confined velocity spread, which makes it ideal to measure proper motions and parallaxes. Eight well-studied massive star forming regions have been observed during five EVN sessions of 24 hours duration each and we present here preliminary results for five of them. We achieve accuracies of up to 51 $\\mu$as, which still have the potential to be proved by more ideal observational circumstances.

  5. Air Breathing Direct Methanol Fuel Cell

    DOE Patents [OSTI]

    Ren; Xiaoming (Los Alamos, NM)

    2003-07-22

    A method for activating a membrane electrode assembly for a direct methanol fuel cell is disclosed. The method comprises operating the fuel cell with humidified hydrogen as the fuel followed by running the fuel cell with methanol as the fuel.

  6. A flow field enabling operating direct methanol fuel cells with highly concentrated methanol

    E-Print Network [OSTI]

    Zhao, Tianshou

    the cathode potential, but also leads to a waste of fuel, lowering the overall efficiency of fuel cell [5A flow field enabling operating direct methanol fuel cells with highly concentrated methanol Q. Xu Available online 8 October 2010 Keywords: Fuel cells Direct methanol fuel cells Concentrated methanol Flow

  7. Low Crossover of Methanol and Water Through Thin Membranes in Direct Methanol Fuel Cells

    E-Print Network [OSTI]

    Low Crossover of Methanol and Water Through Thin Membranes in Direct Methanol Fuel Cells Fuqiang State University, University Park, Pennsylvania 16802, USA Low crossover of both methanol and water through a polymer membrane in a direct methanol fuel cell DMFC is essential for using high concentration

  8. Time-resolved photoelectron imaging of large anionic methanol clusters: ,,Methanol...n

    E-Print Network [OSTI]

    Neumark, Daniel M.

    Time-resolved photoelectron imaging of large anionic methanol clusters: ,,Methanol...n - ,,nČ145; published online 27 June 2007 The dynamics of an excess electron in size-selected methanol clusters electron6­11 and its cluster counterparts,12­18 water n - . The solvated electron in liquid methanol has

  9. A sandwich structured membrane for direct methanol fuel cells operating with neat methanol

    E-Print Network [OSTI]

    Zhao, Tianshou

    A sandwich structured membrane for direct methanol fuel cells operating with neat methanol Q.X. Wu i g h t s " A sandwich structured membrane for DMFCs operating with neat methanol is proposed. " The membrane offers better water management for DMFCs operating with neat methanol. " The sandwich structured

  10. 6, 39453963, 2006 Methanol inside aged

    E-Print Network [OSTI]

    ACPD 6, 3945­3963, 2006 Methanol inside aged tropical biomass burning plumes G. Dufour et al. Title Chemistry and Physics Discussions First space-borne measurements of methanol inside aged tropical biomass. Dufour (gaelle.dufour@lmd.polytechnique.fr) 3945 #12;ACPD 6, 3945­3963, 2006 Methanol inside aged

  11. Methanol and hydrogen from biomass for transportation

    E-Print Network [OSTI]

    Methanol and hydrogen from biomass for transportation [1] Robert H. Williams, Eric D. Larson, Ryan and Applied Science, Princeton University, Princeton, New Jersey 08544, USA Methanol and hydrogen produced-derived methanol and hydrogen would be roughly competitive with these fuels produced on a much larger scale (to

  12. Air breathing direct methanol fuel cell

    DOE Patents [OSTI]

    Ren, Xiaoming (Los Alamos, NM)

    2002-01-01

    An air breathing direct methanol fuel cell is provided with a membrane electrode assembly, a conductive anode assembly that is permeable to air and directly open to atmospheric air, and a conductive cathode assembly that is permeable to methanol and directly contacting a liquid methanol source.

  13. Micro Fuel Cells Direct Methanol Fuel Cells

    E-Print Network [OSTI]

    Micro Fuel Cells TM Direct Methanol Fuel Cells for Portable Power A Fuel Cell System Developer-17, 2002 Phoenix, Arizona #12;Micro Fuel Cells Direct Methanol Fuel Cells for Portable Power Outline (1 Energy Content (Wh) Volume(cm^3) Li-Ion Battery DMFC #12;Direct Methanol Fuel Cell Technology

  14. Methanol Masers and Star Formation

    E-Print Network [OSTI]

    A. M. Sobolev; A. B. Ostrovskii; M. S. Kirsanova; O. V. Shelemei; M. A. Voronkov; A. V. Malyshev

    2006-01-12

    Methanol masers which are traditionally divided into two classes provide possibility to study important parts of the star forming regions: Class~II masers trace vicinities of the massive YSOs while class~I masers are likely to trace more distant parts of the outflows where newer stars can form. There are many methanol transitions which produce observed masers. This allows to use pumping analysis for estimation of the physical parameters in the maser formation regions and its environment, for the study of their evolution. Extensive surveys in different masing transitions allow to conclude on the values of the temperatures, densities, dust properties, etc. in the bulk of masing regions. Variability of the brightest masers is monitored during several years. In some cases it is probably caused by the changes of the dust temperature which follow variations in the brightness of the central YSO reflecting the character of the accretion process. A unified catalogue of the class II methanol masers consisting of more than 500 objects is compiled. Analysis of the data shows that: physical conditions within the usual maser source vary considerably; maser brightness is determined by parameters of some distinguished part of the object - maser formation region; class II methanol masers are formed not within the outflows but in the regions affected by their propagation. It is shown that the "near" solutions for the kinematic distances to the sources can be used for statistical analysis. The luminosity function of the 6.7 GHz methanol masers is constructed. It is shown that improvement of the sensitivity of surveys can increase number of detected maser sources considerably.

  15. Ethanol Myths: Under the Microscope

    E-Print Network [OSTI]

    Pawlowski, Wojtek

    , transport to facility, convert to ethanol, and distribute Future biomass feedstocks will come primarily from

  16. Techno-economic Analysis for the Thermochemical Conversion of Lignocellulosic Biomass to Ethanol via Acetic Acid Synthesis

    SciTech Connect (OSTI)

    Zhu, Yunhua; Jones, Susanne B.

    2009-04-01

    Biomass is a renewable energy resource that can be converted into liquid fuel suitable for transportation applications. As a widely available biomass form, lignocellulosic biomass can have a major impact on domestic transportation fuel supplies and thus help meet the Energy Independence and Security Act renewable energy goals (U.S. Congress 2007). This study performs a techno-economic analysis of the thermo chemical conversion of biomass to ethanol, through methanol and acetic acid, followed by hydrogenation of acetic acid to ethanol. The conversion of syngas to methanol and methanol to acetic acid are well-proven technologies with high conversions and yields. This study was undertaken to determine if this highly selective route to ethanol could provide an already established economically attractive route to ethanol. The feedstock was assumed to be wood chips at 2000 metric ton/day (dry basis). Two types of gasification technologies were evaluated: an indirectly-heated gasifier and a directly-heated oxygen-blown gasifier. Process models were developed and a cost analysis was performed. The carbon monoxide used for acetic acid synthesis from methanol and the hydrogen used for hydrogenation were assumed to be purchased and not derived from the gasifier. Analysis results show that ethanol selling prices are estimated to be $2.79/gallon and $2.81/gallon for the indirectly-heated gasifier and the directly-heated gasifier systems, respectively (1stQ 2008$, 10% ROI). These costs are above the ethanol market price for during the same time period ($1.50 - $2.50/gal). The co-production of acetic acid greatly improves the process economics as shown in the figure below. Here, 20% of the acetic acid is diverted from ethanol production and assumed to be sold as a co-product at the prevailing market prices ($0.40 - $0.60/lb acetic acid), resulting in competitive ethanol production costs.

  17. Enhanced methanol utilization in direct methanol fuel cell

    DOE Patents [OSTI]

    Ren, Xiaoming (Los Alamos, NM); Gottesfeld, Shimshon (Los Alamos, NM)

    2001-10-02

    The fuel utilization of a direct methanol fuel cell is enhanced for improved cell efficiency. Distribution plates at the anode and cathode of the fuel cell are configured to distribute reactants vertically and laterally uniformly over a catalyzed membrane surface of the fuel cell. A conductive sheet between the anode distribution plate and the anodic membrane surface forms a mass transport barrier to the methanol fuel that is large relative to a mass transport barrier for a gaseous hydrogen fuel cell. In a preferred embodiment, the distribution plate is a perforated corrugated sheet. The mass transport barrier may be conveniently increased by increasing the thickness of an anode conductive sheet adjacent the membrane surface of the fuel cell.

  18. Ethanol production from lignocellulose

    DOE Patents [OSTI]

    Ingram, Lonnie O. (Gainesville, FL); Wood, Brent E. (Gainesville, FL)

    2001-01-01

    This invention presents a method of improving enzymatic degradation of lignocellulose, as in the production of ethanol from lignocellulosic material, through the use of ultrasonic treatment. The invention shows that ultrasonic treatment reduces cellulase requirements by 1/3 to 1/2. With the cost of enzymes being a major problem in the cost-effective production of ethanol from lignocellulosic material, this invention presents a significant improvement over presently available methods.

  19. Emissions from two methanol-powered buses

    SciTech Connect (OSTI)

    Ullman, T.L.; Hare, C.T.; Baines, T.M.

    1986-01-01

    Emissions from the two methanol-powered buses used in the California Methanol Bus Demonstration have been characterized. The M.A.N. SU 240 bus is powered by M.A.N.'s D2566 FMUH methanol engine, and utilizes catalytic exhaust aftertreatment. The GMC RTS II 04 bus is powered by a first-generation DDAD 6V-92TA methanol engine without exhaust aftertreatment. Emissions of HC, CO, NO/subX/, unburned methanol, aldehydes, total particulates, and the soluble fraction of particulate were determined for both buses over steady-state and transient chassis dynamometer test cycles. Emission levels from the M.A.N. bus were considerably lower than those from the GMC bus, with the exception of NO/subX/. Comparison of emission levels from methanol-and diesel-powered buses indicates that substantial reductions in emissions are possible with careful implementation of methanol fueling.

  20. Direct methanol fuel cell and system

    DOE Patents [OSTI]

    Wilson, Mahlon S. (Los Alamos, NM)

    2004-10-26

    A fuel cell having an anode and a cathode and a polymer electrolyte membrane located between anode and cathode gas diffusion backings uses a methanol vapor fuel supply. A permeable polymer electrolyte membrane having a permeability effective to sustain a carbon dioxide flux equivalent to at least 10 mA/cm.sup.2 provides for removal of carbon dioxide produced at the anode by reaction of methanol with water. Another aspect of the present invention includes a superabsorpent polymer material placed in proximity to the anode gas diffusion backing to hold liquid methanol or liquid methanol solution without wetting the anode gas diffusion backing so that methanol vapor from the liquid methanol or liquid methanol-water solution is supplied to the membrane.

  1. Methanol in the L1551 Circumbinary Torus

    E-Print Network [OSTI]

    Glenn J. White; C. W. M. Fridlund; P. Bergman; A. Beardsmore; Rene Liseau; R. R. Phillips

    2006-09-25

    We report observations of gaseous methanol in an edge-on torus surrounding the young stellar object L1551 IRS5. The peaks in the torus are separated by ~ 10,000 AU from L1551 IRS5, and contain ~ 0.03 earth masses of cold methanol. We infer that the methanol abundance increases in the outer part of the torus, probably as a result of methanol evaporation from dust grain surfaces heated by the shock luminosity associated with the shocks associated with the jets of an externally located x-ray source. Any methanol released in such a cold environment will rapidly freeze again, spreading methanol throughout the circumbinary torus to nascent dust grains, planitesimals, and primitive bodies. These observations probe the initial chemical conditions of matter infalling onto the disk.

  2. Methods of conditioning direct methanol fuel cells

    DOE Patents [OSTI]

    Rice, Cynthia (Newington, CT); Ren, Xiaoming (Menands, NY); Gottesfeld, Shimshon (Niskayuna, NY)

    2005-11-08

    Methods for conditioning the membrane electrode assembly of a direct methanol fuel cell ("DMFC") are disclosed. In a first method, an electrical current of polarity opposite to that used in a functioning direct methanol fuel cell is passed through the anode surface of the membrane electrode assembly. In a second method, methanol is supplied to an anode surface of the membrane electrode assembly, allowed to cross over the polymer electrolyte membrane of the membrane electrode assembly to a cathode surface of the membrane electrode assembly, and an electrical current of polarity opposite to that in a functioning direct methanol fuel cell is drawn through the membrane electrode assembly, wherein methanol is oxidized at the cathode surface of the membrane electrode assembly while the catalyst on the anode surface is reduced. Surface oxides on the direct methanol fuel cell anode catalyst of the membrane electrode assembly are thereby reduced.

  3. Air breathing direct methanol fuel cell

    DOE Patents [OSTI]

    Ren, Xiaoming (Los Alamos, NM); Gottesfeld, Shimshon (Los Alamos, NM)

    2002-01-01

    An air breathing direct methanol fuel cell is provided with a membrane electrode assembly, a conductive anode assembly that is permeable to air and directly open to atmospheric air, and a conductive cathode assembly that is permeable to methanol and directly contacting a liquid methanol source. Water loss from the cell is minimized by making the conductive cathode assembly hydrophobic and the conductive anode assembly hydrophilic.

  4. Method of steam reforming methanol to hydrogen

    DOE Patents [OSTI]

    Beshty, Bahjat S. (Lower Makefield, PA)

    1990-01-01

    The production of hydrogen by the catalyzed steam reforming of methanol is accomplished using a reformer of greatly reduced size and cost wherein a mixture of water and methanol is superheated to the gaseous state at temperatures of about 800.degree. to about 1,100.degree. F. and then fed to a reformer in direct contact with the catalyst bed contained therein, whereby the heat for the endothermic steam reforming reaction is derived directly from the superheated steam/methanol mixture.

  5. THE FURNACE COMBUSTION AND RADIATION CHARACTERISTICS OF METHANOL AND A METHANOL/COAL SLURRY

    E-Print Network [OSTI]

    Grosshandler, W.L.

    2010-01-01

    difference in optical properties of the coal. more rigorousProperties The fuels used are methanol and a methanol/coalcoal, They discuss , temperature of parti e per- type of viscosity TABLE II-2, Properties

  6. The use of dimethyl ether as a starting aid for methanol-fueled SI engines at low temperatures

    SciTech Connect (OSTI)

    Kozole, K.H.; Wallace, J.S

    1988-01-01

    Methanol-fueled SI engines have proven to be difficult to start at ambient temperatures below approximately 10/sup 0/C. The use of dimethyl ether (DME) is proposed to improve the cold starting performance of methanol-fueled SI engines. Tests to evaluate this idea were carried out with a modified single-cylinder CFR research engine having a compression ratio of 12:1. The engine was fueled with combinations of gaseous dimethyl ether and liquid methanol having DME mass fractions of 30%, 40%, 60% and 70%. For comparison, tests were also carried out with 100% methanol and with winter grade premium unleaded gasoline. Overall stoichiometric mixtures were used in all tests.

  7. Ethanol Myths Fact Sheet

    SciTech Connect (OSTI)

    None

    2009-10-27

    Ethanol is a clean, renewable fuel that is helping to reduce our nation’s dependence on oil and can offer additional economic and environmental benefits in the future. This fact sheet is intended to address some common misconceptions about this important alternative fuel.

  8. Sorghum to Ethanol Research

    SciTech Connect (OSTI)

    Dahlberg, Jeff; Wolfrum, Ed

    2010-06-30

    The development of a robust source of renewable transportation fuel will require a large amount of biomass feedstocks. It is generally accepted that in addition to agricultural and forestry residues, we will need crops grown specifically for subsequent conversion into fuels. There has been a lot of research on several of these so-called �dedicated bioenergy crops� including switchgrass, miscanthus, sugarcane, and poplar. It is likely that all of these crops will end up playing a role as feedstocks, depending on local environmental and market conditions. Many different types of sorghum have been grown to produce syrup, grain, and animal feed for many years. It has several features that may make it as compelling as other crops mentioned above as a renewable, sustainable biomass feedstock; however, very little work has been done to investigate sorghum as a dedicated bioenergy crop. The goal of this project was to investigate the feasibility of using sorghum biomass to produce ethanol. The work performed included a detailed examination of the agronomics and composition of a large number of sorghum varieties, laboratory experiments to convert sorghum to ethanol, and economic and life-cycle analyses of the sorghum-to-ethanol process. This work showed that sorghum has a very wide range of composition, which depended on the specific sorghum cultivar as well as the growing conditions. The results of laboratory- and pilot-scale experiments indicated that a typical high-biomass sorghum variety performed very similarly to corn stover during the multi-step process required to convert biomass feedstocks to ethanol; yields of ethanol for sorghum were very similar to the corn stover used as a control in these experiments. Based on multi-year agronomic data and theoretical ethanol production, sorghum can achieve more than 1,300 gallons of ethanol per acre given the correct genetics and environment. In summary, sorghum may be a compelling dedicated bioenergy crop that could help provide a major portion of the feedstocks required to produce renewable domestic transportation fuels.

  9. Sorghum to Ethanol Research

    SciTech Connect (OSTI)

    Jeff Dahlberg, Ph D; Ed Wolfrum, Ph D

    2010-06-30

    The development of a robust source of renewable transportation fuel will require a large amount of biomass feedstocks. It is generally accepted that in addition to agricultural and forestry residues, we will need crops grown specifically for subsequent conversion into fuels. There has been a lot of research on several of these so-called "dedicated bioenergy crops" including switchgrass, miscanthus, sugarcane, and poplar. It is likely that all of these crops will end up playing a role as feedstocks, depending on local environmental and market conditions. Many different types of sorghum have been grown to produce syrup, grain, and animal feed for many years. It has several features that may make it as compelling as other crops mentioned above as a renewable, sustainable biomass feedstock; however, very little work has been done to investigate sorghum as a dedicated bioenergy crop. The goal of this project was to investigate the feasibility of using sorghum biomass to produce ethanol. The work performed included a detailed examination of the agronomics and composition of a large number of sorghum varieties, laboratory experiments to convert sorghum to ethanol, and economic and life-cycle analyses of the sorghum-to-ethanol process. This work showed that sorghum has a very wide range of composition, which depended on the specific sorghum cultivar as well as the growing conditions. The results of laboratory- and pilot-scale experiments indicated that a typical high-biomass sorghum variety performed very similarly to corn stover during the multi-step process required to convert biomass feedstocks to ethanol; yields of ethanol for sorghum were very similar to the corn stover used as a control in these experiments. Based on multi-year agronomic data and theoretical ethanol production, sorghum can achieve more than 1,300 gallons of ethanol per acre given the correct genetics and environment. In summary, sorghum may be a compelling dedicated bioenergy crop that could help provide a major portion of the feedstocks required to produce renewable domestic transportation fuels.

  10. Ternary Pt/Rh/SnO2 Electrocatalysts for Oxidizing Ethanol to CO2

    SciTech Connect (OSTI)

    Kowal, A.; Li, M; Shao, M; Sasaki, K; Vukmirovic, M; Zhang, J; Marinkovic, N; Liu, P; Frenkel, A; Adzic, R

    2009-01-01

    Ethanol, with its high energy density, likely production from renewable sources and ease of storage and transportation, is almost the ideal combustible for fuel cells wherein its chemical energy can be converted directly into electrical energy. However, commercialization of direct ethanol fuel cells has been impeded by ethanol's slow, inefficient oxidation even at the best electrocatalysts1, 2. We synthesized a ternary PtRhSnO2/C electrocatalyst by depositing platinum and rhodium atoms on carbon-supported tin dioxide nanoparticles that is capable of oxidizing ethanol with high efficiency and holds great promise for resolving the impediments to developing practical direct ethanol fuel cells. This electrocatalyst effectively splits the C-C bond in ethanol at room temperature in acid solutions, facilitating its oxidation at low potentials to CO2, which has not been achieved with existing catalysts. Our experiments and density functional theory calculations indicate that the electrocatalyst's activity is due to the specific property of each of its constituents, induced by their interactions. These findings help explain the high activity of Pt-Ru for methanol oxidation and the lack of it for ethanol oxidation, and point to the way to accomplishing the C-C bond splitting in other catalytic processes.

  11. Ternary Pt/Rh/SnO2 Electrocatalysts for Oxidizing Ethanol to CO2

    SciTech Connect (OSTI)

    Adzic, R.R.; Kowal, A.; Li, M.; Shao, M.; Sasaki, K.; Vukmirovic, M.B.; Zhang, J.; Marinkovic, N.S. Liu, P.; Frenkel, A.I.

    2009-04-01

    Ethanol, with its high energy density, likely production from renewable sources and ease of storage and transportation, is almost the ideal combustible for fuel cells wherein its chemical energy can be converted directly into electrical energy. However, commercialization of direct ethanol fuel cells has been impeded by ethanol's slow, inefficient oxidation even at the best electrocatalysts. We synthesized a ternary PtRhSnO{sub 2}/C electrocatalyst by depositing platinum and rhodium atoms on carbon-supported tin dioxide nanoparticles that is capable of oxidizing ethanol with high efficiency and holds great promise for resolving the impediments to developing practical direct ethanol fuel cells. This electrocatalyst effectively splits the C-C bond in ethanol at room temperature in acid solutions, facilitating its oxidation at low potentials to CO{sub 2}, which has not been achieved with existing catalysts. Our experiments and density functional theory calculations indicate that the electrocatalyst's activity is due to the specific property of each of its constituents, induced by their interactions. These findings help explain the high activity of Pt-Ru for methanol oxidation and the lack of it for ethanol oxidation, and point to the way to accomplishing the C-C bond splitting in other catalytic processes.

  12. Gasoline from Wood via Integrated Gasification, Synthesis, and Methanol-to-Gasoline Technologies

    SciTech Connect (OSTI)

    Phillips, S. D.; Tarud, J. K.; Biddy, M. J.; Dutta, A.

    2011-01-01

    This report documents the National Renewable Energy Laboratory's (NREL's) assessment of the feasibility of making gasoline via the methanol-to-gasoline route using syngas from a 2,000 dry metric tonne/day (2,205 U.S. ton/day) biomass-fed facility. A new technoeconomic model was developed in Aspen Plus for this study, based on the model developed for NREL's thermochemical ethanol design report (Phillips et al. 2007). The necessary process changes were incorporated into a biomass-to-gasoline model using a methanol synthesis operation followed by conversion, upgrading, and finishing to gasoline. Using a methodology similar to that used in previous NREL design reports and a feedstock cost of $50.70/dry ton ($55.89/dry metric tonne), the estimated plant gate price is $16.60/MMBtu ($15.73/GJ) (U.S. $2007) for gasoline and liquefied petroleum gas (LPG) produced from biomass via gasification of wood, methanol synthesis, and the methanol-to-gasoline process. The corresponding unit prices for gasoline and LPG are $1.95/gallon ($0.52/liter) and $1.53/gallon ($0.40/liter) with yields of 55.1 and 9.3 gallons per U.S. ton of dry biomass (229.9 and 38.8 liters per metric tonne of dry biomass), respectively.

  13. Polyvinylidene Fluoride-Based Membranes for Direct Methanol Fuel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Polyvinylidene Fluoride-Based Membranes for Direct Methanol Fuel Cell Applications Polyvinylidene Fluoride-Based Membranes for Direct Methanol Fuel Cell Applications Download the...

  14. Transport diffusion of liquid water and methanol through membranes...

    Office of Scientific and Technical Information (OSTI)

    Transport diffusion of liquid water and methanol through membranes Citation Details In-Document Search Title: Transport diffusion of liquid water and methanol through membranes The...

  15. Novel Materials for High Efficiency Direct Methanol Fuel Cells...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Materials for High Efficiency Direct Methanol Fuel Cells Novel Materials for High Efficiency Direct Methanol Fuel Cells Presented at the Department of Energy Fuel Cell Projects...

  16. Novel Approach to Advanced Direct Methanol Fuel Cell Anode Catalysts...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Approach to Advanced Direct Methanol Fuel Cell Anode Catalysts Novel Approach to Advanced Direct Methanol Fuel Cell Anode Catalysts Presented at the Department of Energy Fuel Cell...

  17. Advancing Cellulosic Ethanol for Large Scale Sustainable Transportation

    E-Print Network [OSTI]

    Wyman, C

    2007-01-01

    Advancing Cellulosic Ethanol for Large Scale SustainableHydrogen Batteries Nuclear By Lee Lynd, Dartmouth EthanolEthanol, ethyl alcohol, fermentation ethanol, or just “

  18. Reducing Greenhouse Emissions and Fuel Consumption

    E-Print Network [OSTI]

    Shaheen, Susan; Lipman, Timothy

    2007-01-01

    engine (typically Otto, Diesel, or Atkinson- cycle) vehicles running on gasoline, diesel, bio-diesel, ethanol, methanol, compressed natural gas, liquefied propane

  19. Fuel-Cycle Energy and Emissions Analysis with the GREET Model

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    petroleum gas * Gaseous and liquid hydrogen * Methanol and ethanol Compression-Ignition Direct-Injection Hybrid Electric Vehicles: Grid-Independent and Connected * Conventional...

  20. Ethanol Consumption by Rat Dams During Gestation,

    E-Print Network [OSTI]

    Galef Jr., Bennett G.

    Ethanol Consumption by Rat Dams During Gestation, Lactation and Weaning Increases Ethanol examined effects of ethanol consumption in rat dams during gestation, lactation, and weaning on voluntary ethanol consumption by their adolescent young. We found that exposure to an ethanol-ingesting dam

  1. Ethanol production by Zymomonas mobilis

    SciTech Connect (OSTI)

    Strandberg, G.W.; Scott, C.D.; Donaldson, T.L.; Worden, R.M.

    1983-01-01

    Research progress is described on the development of laboratory-scale columnar bioreactors utilizing the flocculent bacterium, X. mobilis, for ethanol production. X. mobilis forms stable, ball-like aggregates which maintain structural integrity even when subjected to the high shear forces generated in the active 3-phase fluidized-bed reactors. Cell retention and ethanol production were studied using 3 bioreactor configurations. Ethanol productivity appeared to be primarily affected by glucose feed concentration. In addition, it was found that in the absence of nutrients, the level of ethanol productivity can be maintained for at least 1 h before a severe drop occurred. Ethanol inhibition is considered to be a limiting factor in ethanol production. (DMC)

  2. Communication China's growing methanol economy and its implications for energy

    E-Print Network [OSTI]

    Jackson, Robert B.

    , 2011). The rapid expansion of methanol and DME as fuels in China appears to fit Nobel Laureate George petroleum-based fuels and chemicals with methanol and methanol-derivatives ­ as a path to sustainable quickly built an industry of coal-based methanol and dimethyl ether (DME) that is competitive in price

  3. Homogeneous catalyst formulations for methanol production

    DOE Patents [OSTI]

    Mahajan, Devinder (Port Jefferson, NY); Sapienza, Richard S. (Shoreham, NY); Slegeir, William A. (Hampton Bays, NY); O'Hare, Thomas E. (Huntington Station, NY)

    1991-02-12

    There is disclosed synthesis of CH.sub.3 OH from carbon monoxide and hydrogen using an extremely active homogeneous catalyst for methanol synthesis directly from synthesis gas. The catalyst operates preferably between 100.degree.-150.degree. C. and preferably at 100-150 psia synthesis gas to produce methanol. Use can be made of syngas mixtures which contain considerable quantities of other gases, such as nitrogen, methane or excess hydrogen. The catalyst is composed of two components: (a) a transition metal carbonyl complex and (b) an alkoxide component. In the simplest formulation, component (a) is a complex of nickel tetracarbonyl and component (b) is methoxide (CH.sub.3 O.sup.-), both being dissolved in a methanol solvent system. The presence of a co-solvent such as p-dioxane, THF, polyalcohols, ethers, hydrocarbons, and crown ethers accelerates the methanol synthesis reaction.

  4. Methanol Maser Polarization in W3(OH)

    E-Print Network [OSTI]

    W. H. T. Vlemmings; L. Harvey-Smith; R. J. Cohen

    2006-06-13

    We present the first 6.7 GHz methanol maser linear polarization map of the extended filamentary maser structure around the compact HII region W3(OH). The methanol masers show linear polarization up to 8 per cent and the polarization angles indicate a magnetic field direction along the North-South maser structure. The polarization angles are consistent with those measured for the OH masers, taking into account external Faraday rotation toward W3(OH), and confirm that the OH and methanol masers are found in similar physical conditions. Additionally we discuss the Zeeman splitting of the 6.7 GHz methanol transition and present an upper limit of ~22 mG for the magnetic field strength in the maser region. The upper limit is fully consistent with the field strengths derived from OH maser Zeeman splitting.

  5. Homogeneous catalyst formulations for methanol production

    DOE Patents [OSTI]

    Mahajan, Devinder (Port Jefferson, NY); Sapienza, Richard S. (Shoreham, NY); Slegeir, William A. (Hampton Bays, NY); O'Hare, Thomas E. (Huntington Station, NY)

    1990-01-01

    There is disclosed synthesis of CH.sub.3 OH from carbon monoxide and hydrogen using an extremely active homogeneous catalyst for methanol synthesis directly from synthesis gas. The catalyst operates preferably between 100.degree.-150.degree. C. and preferably at 100-150 psia synthesis gas to produce methanol. Use can be made of syngas mixtures which contain considerable quantities of other gases, such as nitrogen, methane or excess hydrogen. The catalyst is composed of two components: (a) a transition metal carbonyl complex and (b) an alkoxide component. In the simplest formulation, component (a) is a complex of nickel tetracarbonyl and component (b) is methoxide (CH.sub.3 O.sup.13 ), both being dissolved in a methanol solvent system. The presence of a co-solvent such as p-dioxane, THF, polyalcohols, ethers, hydrocarbons, and crown ethers accelerates the methanol synthesis reaction.

  6. Methanol-tolerant cathode catalyst composite for direct methanol fuel cells

    DOE Patents [OSTI]

    Zhu, Yimin (Los Alamos, NM); Zelenay, Piotr (Los Alamos, NM)

    2006-09-05

    A direct methanol fuel cell (DMFC) having a methanol fuel supply, oxidant supply, and its membrane electrode assembly (MEA) formed of an anode electrode and a cathode electrode with a membrane therebetween, a methanol oxidation catalyst adjacent the anode electrode and the membrane, an oxidant reduction catalyst adjacent the cathode electrode and the membrane, comprises an oxidant reduction catalyst layer of Pt.sub.3Cr/C so that oxidation at the cathode of methanol that crosses from the anode through the membrane to the cathode is reduced with a concomitant increase of net electrical potential at the cathode electrode.

  7. Vacuum-ultraviolet (VUV) photoionization of small methanol and methanol-water clusters

    SciTech Connect (OSTI)

    Ahmed, Musahid; Ahmed, Musahid; Wilson, Kevin R.; Belau, Leonid; Kostko, Oleg

    2008-05-12

    In this work we report on thevacuum-ultraviolet (VUV) photoionization of small methanol and methanol-water clusters. Clusters of methanol with water are generated via co-expansion of the gas phase constituents in a continuous supersonic jet expansion of methanol and water seeded in Ar. The resulting clusters are investigated by single photon ionization with tunable vacuumultraviolet synchrotron radiation and mass analyzed using reflectron mass spectrometry. Protonated methanol clusters of the form (CH3OH)nH + (n=1-12) dominate the mass spectrum below the ionization energy of the methanol monomer. With an increase in water concentration, small amounts of mixed clusters of the form (CH3OH)n(H2O)H + (n=2-11) are detected. The only unprotonated species observed in this work are the methanol monomer and dimer. Appearance energies are obtained from the photoionization efficiency (PIE) curves for CH3OH +, (CH 3OH)2 +, (CH3OH)nH + (n=1-9), and (CH 3OH)n(H2O)H + (n=2-9 ) as a function of photon energy. With an increase in the water content in the molecular beam, there is an enhancement of photoionization intensity for methanol dimer and protonated methanol monomer at threshold. These results are compared and contrasted to previous experimental observations.

  8. Methanol-Tolerant Cathode Catalyst Composite For Direct Methanol Fuel Cells

    DOE Patents [OSTI]

    Zhu, Yimin (Los Alamos, NM); Zelenay, Piotr (Los Alamos, NM)

    2006-03-21

    A direct methanol fuel cell (DMFC) having a methanol fuel supply, oxidant supply, and its membrane electrode assembly (MEA) formed of an anode electrode and a cathode electrode with a membrane therebetween, a methanol oxidation catalyst adjacent the anode electrode and the membrane, an oxidant reduction catalyst adjacent the cathode electrode and the membrane, comprises an oxidant reduction catalyst layer of a platinum-chromium alloy so that oxidation at the cathode of methanol that crosses from the anode through the membrane to the cathode is reduced with a concomitant increase of net electrical potential at the cathode electrode.

  9. Vacuum-Ultraviolet (VUV) Photoionization of Small Methanol and Methanol-Water Clusters

    SciTech Connect (OSTI)

    Kostko, Oleg; Belau, Leonid; Wilson, Kevin R.; Ahmed, Musahid

    2008-04-24

    In this work, we report on the vacuum-ultraviolet (VUV) photoionization of small methanol and methanol-water clusters. Clusters of methanol with water are generated via co-expansion of the gas phase constituents in a continuous supersonic jet expansion of methanol and water seeded in Ar. The resulting clusters are investigated by single photon ionization with tunable vacuum-ultraviolet synchrotron radiation and mass analyzed using reflectron mass spectrometry. Protonated methanol clusters of the form (CH3OH)nH+(n = 1-12) dominate the mass spectrum below the ionization energy of the methanol monomer. With an increase in water concentration, small amounts of mixed clusters of the form (CH3OH n(H2O)H+ (n = 2-11) are detected. The only unprotonated species observed in this work are the methanol monomer and dimer. Appearance energies are obtained from the photoionization efficiency (PIE) curves for CH3OH+, (CH3OH)2+, (CH3OH)nH+ (n = 1-9), and (CH3OH)n(H2O)H+ (n = 2-9) as a function of photon energy. With an increasein the water content in the molecular beam, there is an enhancement of photoionization intensity for the methanol dimer and protonated methanol monomer at threshold. These results are compared and contrasted to previous experimental observations.

  10. Federal Methanol Fleet Project final report

    SciTech Connect (OSTI)

    West, B.H.; McGill, R.N.; Hillis, S.L.; Hodgson, J.W.

    1993-03-01

    The Federal Methanol Fleet Project concluded with the termination of data collection from the three fleet sites in February 1991. The Lawrence Berkeley Laboratory (LBL) completed five years of operation, Argonne National Laboratory (ANL) completed its fourth year in the project, and Oak Ridge National Laboratory (ORNL) completed its third. Twenty of the thirty-nine vehicles in the fleet were powered by fuel methanol (typically M85, 85 % methanol, 15 % unleaded gasoline, although the LBL fleet used M88), and the remaining control vehicles were comparable gasoline vehicles. Over 2.2 million km (1.4 million miles) were accumulated on the fleet vehicles in routine government service. Data collected over the years have included vehicle mileage and fuel economy, engine oil analysis, emissions, vehicle maintenance, and driver acceptance. Fuel economies (on an energy basis) of the methanol and gasoline vehicles of the same type were comparable throughout the fleet testing. Engine oil analysis has revealed higher accumulation rates of iron and other metals in the oil of the methanol vehicles, although no significant engine damage has been attributed to the higher metal content. Vehicles of both fuel types have experienced degradation in their emission control systems, however, the methanol vehicles seem to have degraded their catalytic converters at a higher rate. The methanol vehicles have required more maintenance than their gasoline counterparts, in most cases, although the higher levels of maintenance cannot be attributed to ``fuel-related`` repairs. According to the daily driver logs and results from several surveys, drivers of the fleet vehicles at all three sites were generally satisfied with the methanol vehicles.

  11. Federal Methanol Fleet Project final report

    SciTech Connect (OSTI)

    West, B.H.; McGill, R.N. ); Hillis, S.L.; Hodgson, J.W. )

    1993-03-01

    The Federal Methanol Fleet Project concluded with the termination of data collection from the three fleet sites in February 1991. The Lawrence Berkeley Laboratory (LBL) completed five years of operation, Argonne National Laboratory (ANL) completed its fourth year in the project, and Oak Ridge National Laboratory (ORNL) completed its third. Twenty of the thirty-nine vehicles in the fleet were powered by fuel methanol (typically M85, 85 % methanol, 15 % unleaded gasoline, although the LBL fleet used M88), and the remaining control vehicles were comparable gasoline vehicles. Over 2.2 million km (1.4 million miles) were accumulated on the fleet vehicles in routine government service. Data collected over the years have included vehicle mileage and fuel economy, engine oil analysis, emissions, vehicle maintenance, and driver acceptance. Fuel economies (on an energy basis) of the methanol and gasoline vehicles of the same type were comparable throughout the fleet testing. Engine oil analysis has revealed higher accumulation rates of iron and other metals in the oil of the methanol vehicles, although no significant engine damage has been attributed to the higher metal content. Vehicles of both fuel types have experienced degradation in their emission control systems, however, the methanol vehicles seem to have degraded their catalytic converters at a higher rate. The methanol vehicles have required more maintenance than their gasoline counterparts, in most cases, although the higher levels of maintenance cannot be attributed to fuel-related'' repairs. According to the daily driver logs and results from several surveys, drivers of the fleet vehicles at all three sites were generally satisfied with the methanol vehicles.

  12. Vehicle Technologies Office: Intermediate Ethanol Blends

    Broader source: Energy.gov [DOE]

    Ethanol can be combined with gasoline in blends ranging from E10 (10% or less ethanol, 90% gasoline) up to E85 (up to 85% ethanol, 15% gasoline). The Renewable Fuels Standard (under the Energy...

  13. Algenol Announces Commercial Algal Ethanol Fuel Partnership ...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Algenol Announces Commercial Algal Ethanol Fuel Partnership Algenol Announces Commercial Algal Ethanol Fuel Partnership October 21, 2015 - 10:35am Addthis An error occurred. Try...

  14. Louisiana: Verenium Cellulosic Ethanol Demonstration Facility...

    Office of Environmental Management (EM)

    Louisiana: Verenium Cellulosic Ethanol Demonstration Facility Louisiana: Verenium Cellulosic Ethanol Demonstration Facility April 9, 2013 - 12:00am Addthis In 2010, Verenium...

  15. Algenol Announces Commercial Algal Ethanol Fuel Partnership ...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Algenol Announces Commercial Algal Ethanol Fuel Partnership Algenol Announces Commercial Algal Ethanol Fuel Partnership October 2, 2015 - 11:28am Addthis An error occurred. Try...

  16. Ethanol production in non-recombinant hosts

    DOE Patents [OSTI]

    Kim, Youngnyun; Shanmugam, Keelnatham; Ingram, Lonnie O.

    2013-06-18

    Non-recombinant bacteria that produce ethanol as the primary fermentation product, associated nucleic acids and polypeptides, methods for producing ethanol using the bacteria, and kits are disclosed.

  17. Electronic Effect in Methanol Dehydrogenation on Pt Surfaces: Potential Control during Methanol Electrooxidation

    E-Print Network [OSTI]

    Park, Byungwoo

    advanced insight into the design of an optimal catalyst as the anode for direct methanol fuel cells. SECTION: Energy Conversion and Storage; Energy and Charge Transport Fuel cells are promising alternative energy conversion. Polymer electrolyte membrane fuel cells (PEMFCs) and direct methanol fuel cells (DMFCs

  18. Effect of the cathode gas diffusion layer on the water transport behavior and the performance of passive direct methanol fuel cells operating with neat methanol

    E-Print Network [OSTI]

    Zhao, Tianshou

    of passive direct methanol fuel cells operating with neat methanol Q.X. Wu, T.S. Zhao , W.W. Yang Department Direct methanol fuel cell Passive operation Neat methanol operation a b s t r a c t The passive operation of a direct methanol fuel cell with neat methanol requires the water that is pro- duced at the cathode

  19. Comparison of Methanol Exposure Routes Reported to Texas Poison Control Centers

    E-Print Network [OSTI]

    Givens, Melissa; Kalbfleisch, Kristine; Bryson, Scott

    2008-01-01

    guidelines on the treatment of methanol poisoning, J ToxicolHantson PE, Acute methanol intoxication: physiopathology,The toxicity of inhaled methanol vapors, Crit Rev Toxicol.

  20. Methanol sensor operated in a passive mode

    DOE Patents [OSTI]

    Ren, Xiaoming (Los Alamos, NM); Gottesfeld, Shimshon (Los Alamos, NM)

    2002-01-01

    A sensor outputs a signal related to a concentration of methanol in an aqueous solution adjacent the sensor. A membrane electrode assembly (MEA) is included with an anode side and a cathode side. An anode current collector supports the anode side of the MEA and has a flow channel therethrough for flowing a stream of the aqueous solution and forms a physical barrier to control access of the methanol to the anode side of the MEA. A cathode current collector supports the cathode side of the MEA and is configured for air access to the cathode side of the MEA. A current sensor is connected to measure the current in a short circuit across the sensor electrodes to provide an output signal functionally related to the concentration of methanol in the aqueous solution.

  1. Thermally integrated staged methanol reformer and method

    DOE Patents [OSTI]

    Skala, Glenn William (Churchville, NY); Hart-Predmore, David James (Rochester, NY); Pettit, William Henry (Rochester, NY); Borup, Rodney Lynn (East Rochester, NY)

    2001-01-01

    A thermally integrated two-stage methanol reformer including a heat exchanger and first and second reactors colocated in a common housing in which a gaseous heat transfer medium circulates to carry heat from the heat exchanger into the reactors. The heat transfer medium comprises principally hydrogen, carbon dioxide, methanol vapor and water vapor formed in a first stage reforming reaction. A small portion of the circulating heat transfer medium is drawn off and reacted in a second stage reforming reaction which substantially completes the reaction of the methanol and water remaining in the drawn-off portion. Preferably, a PrOx reactor will be included in the housing upstream of the heat exchanger to supplement the heat provided by the heat exchanger.

  2. Corn Ethanol -April 2006 11 Cover Story

    E-Print Network [OSTI]

    Patzek, Tadeusz W.

    Corn Ethanol - April 2006 11 Cover Story orn ethanol is the fuel du jour. It's domestic. It's not oil. Ethanol's going to help promote "energy independence." Magazines trumpet it as the motor vehicle Midwest fields, waiting to rot or be processed into ethanol. Interestingly, the National Corn Growers

  3. 37 GHz METHANOL MASERS : HORSEMEN OF THE APOCALYPSE FOR THE CLASS II METHANOL MASER PHASE?

    SciTech Connect (OSTI)

    Ellingsen, S. P.; Breen, S. L. [School of Mathematics and Physics, University of Tasmania, Private Bag 37, Hobart, TAS 7001 (Australia); Sobolev, A. M. [Astronomical Observatory, Ural Federal University, Lenin avenue 51, 620000 Ekaterinburg (Russian Federation); Voronkov, M. A.; Caswell, J. L. [CSIRO Astronomy and Space Science, Australia Telescope National Facility, P.O. Box 76, Epping, NSW 1710 (Australia); Lo, N., E-mail: Simon.Ellingsen@utas.edu.au [Departamento de Astronomia, Universidad de Chile, Camino El Observatorio 1515, Las Condes, Santiago, Casilla 36-D (Chile)

    2011-12-01

    We report the results of a search for class II methanol masers at 37.7, 38.3, and 38.5 GHz toward a sample of 70 high-mass star formation regions. We primarily searched toward regions known to show emission either from the 107 GHz class II methanol maser transition, or from the 6.035 GHz excited OH transition. We detected maser emission from 13 sources in the 37.7 GHz transition, eight of these being new detections. We detected maser emission from three sources in the 38 GHz transitions, one of which is a new detection. We find that 37.7 GHz methanol masers are only associated with the most luminous 6.7 and 12.2 GHz methanol maser sources, which in turn are hypothesized to be the oldest class II methanol sources. We suggest that the 37.7 GHz methanol masers are associated with a brief evolutionary phase (of 1000-4000 years) prior to the cessation of class II methanol maser activity in the associated high-mass star formation region.

  4. Liquid phase methanol reactor staging process for the production of methanol

    DOE Patents [OSTI]

    Bonnell, Leo W. (Macungie, PA); Perka, Alan T. (Macungie, PA); Roberts, George W. (Emmaus, PA)

    1988-01-01

    The present invention is a process for the production of methanol from a syngas feed containing carbon monoxide, carbon dioxide and hydrogen. Basically, the process is the combination of two liquid phase methanol reactors into a staging process, such that each reactor is operated to favor a particular reaction mechanism. In the first reactor, the operation is controlled to favor the hydrogenation of carbon monoxide, and in the second reactor, the operation is controlled so as to favor the hydrogenation of carbon dioxide. This staging process results in substantial increases in methanol yield.

  5. Ethanol Waivers: Needed or Irrelevant? 

    E-Print Network [OSTI]

    Griffin, James M.; Dahl, Rachel

    2012-01-01

    Because of the magnitude of the existing corn harvest shortfall coupled with the large ethanol mandates, policymakers face extreme uncertainties looking into the future with potentially large economic ramifications. Precisely, because neither...

  6. Photoelectron imaging of large anionic methanol clusters: ,,n70460...

    E-Print Network [OSTI]

    Neumark, Daniel M.

    been described elsewhere.9 Methanol cluster anions were produced by passing argon through a reservoir of methanol and expanding the gas mixture through a piezoelectrically actuated valve with a pulsed electron

  7. A stochastic feasibility study of Texas ethanol production: analysis of Texas Legislature ethanol subsidy proposal 

    E-Print Network [OSTI]

    Gill, Robert Chope

    2002-01-01

    The recent resurgence of interest in ethanol production has prompted the Texas State Legislature to investigate the feasibility of ethanol production in Texas. The reasons for the increased interest in ethanol production ...

  8. Methanol production from Eucalyptus wood chips. Final report

    SciTech Connect (OSTI)

    Fishkind, H.H.

    1982-06-01

    This feasibility study includes all phases of methanol production from seedling to delivery of finished methanol. The study examines: production of 55 million, high quality, Eucalyptus seedlings through tissue culture; establishment of a Eucalyptus energy plantation on approximately 70,000 acres; engineering for a 100 million gallon-per-day methanol production facility; potential environmental impacts of the whole project; safety and health aspects of producing and using methanol; and development of site specific cost estimates.

  9. Methanol emission from low mass protostars

    E-Print Network [OSTI]

    S. Maret; C. Ceccarelli; A. G. G. M. Tielens; E. Caux; B. Lefloch; A. Faure; A. Castets; D. R. Flower

    2005-07-15

    We present observations of methanol lines in a sample of Class 0 low mass protostars. Using a 1-D radiative transfer model, we derive the abundances in the envelopes. In two sources of the sample, the observations can only be reproduced by the model if the methanol abundance is enhanced by about two order of magnitude in the inner hot region of the envelope. Two other sources show similar jumps, although at a lower confidence level. The observations for the other three sources are well reproduced with a constant abundance, but the presence of a jump cannot be ruled out. The observed methanol abundances in the warm gas around low mass protostars are orders of magnitude higher than gas phase chemistry models predict. Hence, in agreement with other evidences, this suggest that the high methanol abundance reflects recent evaporation of ices due to the heating by the newly formed star. The observed abundance ratios of CH3 OH, H2 CO, and CO are in good agreement with grain surface chemistry models. However, the absolute abundances are more difficult to reproduce and may point towards the presence of multiple ice components in these regions.

  10. Methanol Steam Reformer on a Silicon Wafer

    SciTech Connect (OSTI)

    Park, H; Malen, J; Piggott, T; Morse, J; Sopchak, D; Greif, R; Grigoropoulos, C; Havstad, M; Upadhye, R

    2004-04-15

    A study of the reforming rates, heat transfer and flow through a methanol reforming catalytic microreactor fabricated on a silicon wafer are presented. Comparison of computed and measured conversion efficiencies are shown to be favorable. Concepts for insulating the reactor while maintaining small overall size and starting operation from ambient temperature are analyzed.

  11. Methanol Masers as Tracers of Circumstellar Disks

    E-Print Network [OSTI]

    R. P. Norris; S. E. Byleveld; P. J. Diamond; S. P. Ellingsen; R. H. Ferris; R. G. Gough; M. J. Kesteven; P. M. McCulloch; C. J. Phillips; J. E. Reynolds; A. K. Tzioumis; Y. Takahashi; E. R. Troup; K. J. Wellington

    1998-06-25

    We show that in many methanol maser sources the masers are located in lines, with a velocity gradient along them which suggests that the masers are situated in edge-on circumstellar, or protoplanetary, disks. We present VLBI observations of the methanol maser source G309.92+0.48, in the 12.2 GHz transition, which confirm previous observations that the masers in this source lie along a line. We show that such sources are not only linear in space but, in many cases, also have a linear velocity gradient. We then model these and other data in both the 6.7 GHz and the 12.2 GHz transition from a number of star formation regions, and show that the observed spatial and velocity distribution of methanol masers, and the derived Keplerian masses, are consistent with a circumstellar disk rotating around an OB star. We consider this and other hypotheses, and conclude that about half of these methanol masers are probably located in edge-on circumstellar disks around young stars. This is of particular significance for studies of circumstellar disks because of the detailed velocity information available from the masers.

  12. The Impact of Low Octane Hydrocarbon Blending Streams on Ethanol Engine Optimization

    SciTech Connect (OSTI)

    Szybist, James P; West, Brian H

    2013-01-01

    Ethanol is a very attractive fuel from an end-use perspective because it has a high chemical octane number and a high latent heat of vaporization. When an engine is optimized to take advantage of these fuel properties, both efficiency and power can be increased through higher compression ratio, direct fuel injection, higher levels of boost, and a reduced need for enrichment to mitigate knock or protect the engine and aftertreatment system from overheating. The ASTM D5798 specification for high level ethanol blends, commonly called E85, underwent a major revision in 2011. The minimum ethanol content was revised downward from 68 vol% to 51 vol%, which combined with the use of low octane blending streams such as natural gasoline introduces the possibility of a lower octane E85 fuel. While this fuel is suitable for current ethanol tolerant flex fuel vehicles, this study experimentally examines whether engines can still be aggressively optimized for the resultant fuel from the revised ASTM D5798 specification. The performance of six ethanol fuel blends, ranging from 51-85% ethanol, is compared to a premium-grade certification gasoline (UTG-96) in a single-cylinder direct-injection (DI) engine with a compression ratio of 12.9:1 at knock-prone engine conditions. UTG-96 (RON = 96.1), light straight run gasoline (RON = 63.6), and n-heptane (RON = 0) are used as the hydrocarbon blending streams for the ethanol-containing fuels in an effort to establish a broad range of knock resistance for high ethanol fuels. Results show that nearly all ethanol-containing fuels are more resistant to engine knock than UTG-96 (the only exception being the ethanol blend with 49% n-heptane). This knock resistance allows ethanol blends made with 33 and 49% light straight run gasoline, and 33% n-heptane to be operated at significantly more advanced combustion phasing for higher efficiency, as well as at higher engine loads. While experimental results show that the octane number of the hydrocarbon blend stock does impact engine performance, there remains a significant opportunity for engine optimization when considering even the lowest octane fuels that are in compliance with the current revision of ASTM D5798 compared to premium-grade gasoline.

  13. Vapor-liquid equilibria for the methanol-benzene and methanol-thiophene systems

    SciTech Connect (OSTI)

    Toghiani, H.; Toghiani, R.K.; Viswanath, D.S. (Univ. of Missouri, Columbia, MO (United States). Dept. of Chemical Engineering)

    1994-01-01

    The equilibrium still of Rogalski and Malanowski was modified to collect data for the methanol-benzene and methanol-thiophene systems. Two isothermal sets (318.15 and 323.15 K) and one isobaric set (60.03 kPa) of data are presented for the system containing thiophene. For this system, data have not been reported in the literature for the 323.15 K isotherm nor for any isobar. In addition, isothermal data at 318.15 K and isobaric data at 69.52 kPa are presented for the methanol-benzene system. The data presented for methanol-benzene agree with available literature data. However, data for approximately twice as many compositions in the dilute composition region as are available in the literature have been measured in this work. Data in this region are useful for extracting infinite dilution values for the activity coefficients.

  14. THE FURNACE COMBUSTION AND RADIATION CHARACTERISTICS OF METHANOL AND A METHANOL/COAL SLURRY

    E-Print Network [OSTI]

    Grosshandler, W.L.

    2010-01-01

    the structure and radiation heat transfer in a pure methanolHowell, Thermal Radiation Heat Transfer, McGraw-Hill Bookof in- creased radiation heat transfer from the flame zone

  15. Compressed gas manifold

    DOE Patents [OSTI]

    Hildebrand, Richard J. (Edgemere, MD); Wozniak, John J. (Columbia, MD)

    2001-01-01

    A compressed gas storage cell interconnecting manifold including a thermally activated pressure relief device, a manual safety shut-off valve, and a port for connecting the compressed gas storage cells to a motor vehicle power source and to a refueling adapter. The manifold is mechanically and pneumatically connected to a compressed gas storage cell by a bolt including a gas passage therein.

  16. Bimetallic Cluster Provides a Higher Activity Electrocatalyst for Methanol Oxidation*

    E-Print Network [OSTI]

    Weidner, John W.

    Bimetallic Cluster Provides a Higher Activity Electrocatalyst for Methanol Oxidation* Brenda L:Ru nanoparticles on carbon (PtRu/C) for use as an electrocatalyst for methanol oxidation. This bimetallic carbonyl support particles. Cyclic voltammo- grams of methanol oxidation from the two catalysts showed

  17. Fuel Cells Bulletin February 2005 Effect of methanol

    E-Print Network [OSTI]

    Zhao, Tianshou

    FEATURE Fuel Cells Bulletin February 2005 12 Effect of methanol concentration on passive DMFC performance The direct methanol fuel cell (DMFC) has attracted extensive interest from scientists energy density of methanol (6100 W h/kg at 25°C) is much higher than that of gaseous fuels.[1­6] Recently

  18. Dissociative recombination of protonated methanol W. D. Geppert,*a

    E-Print Network [OSTI]

    Millar, Tom

    Dissociative recombination of protonated methanol W. D. Geppert,*a M. Hamberg,a R. D. Thomas,a F. O located in Stockholm, Sweden. Analysis of the data yielded the result that formation of methanol or deuterated methanol accounted for only 3 and 6% of the total rate in CH3OH2 + and CD3OD2 + , respectively

  19. Effects of Methanol on the Retinal Function of Juvenile Rats

    E-Print Network [OSTI]

    Casanova, Christian

    Effects of Methanol on the Retinal Function of Juvenile Rats C. Plaziac1 , P. Lachapelle2 , C Received 18 April 2002; accepted 22 July 2002 Abstract We have investigated the effect of methanol exposure recorded prior to and up to 72 h after the administration of methanol. Data were compared to a control

  20. First satellite observations of lower tropospheric ammonia and methanol

    E-Print Network [OSTI]

    First satellite observations of lower tropospheric ammonia and methanol Reinhard Beer,1 Mark W) and methanol (CH3OH), well above the normal background levels. This is the first time that these molecules have. Citation: Beer, R., et al. (2008), First satellite observations of lower tropospheric ammonia and methanol

  1. Adsorption of intact methanol on Ru,,0001... Pawel Gazdzicki,1

    E-Print Network [OSTI]

    Adsorption of intact methanol on Ru,,0001... Pawel Gazdzicki,1 Per Uvdal,2 and Peter Jakob1,a 1 the adsorption of methanol on the clean Ru 0001 surface at T 80 K. Thereby, clear evidence for intact adsorption upon adsorption of methanol on Ru 0001 , even at low temperatures, as well as partial recombinative

  2. Homogeneous Catalysis Selective Oxidation of Methane to Methanol

    E-Print Network [OSTI]

    Goddard III, William A.

    Homogeneous Catalysis Selective Oxidation of Methane to Methanol Catalyzed, with CŔH Activation (generated by dissolution[6] of Au2O3) react with methane at 1808C to selectively generate methanol (as a mixture of the ester and methanol) in high yield (Table 1, entries 1 and 2). As expected, the irreversible

  3. Methanol maser survey using the EVN Anna Bartkiewicz

    E-Print Network [OSTI]

    van Langevelde, Huib Jan

    Methanol maser survey using the EVN Anna Bartkiewicz Centre for Astronomy, Nicolaus Copernicus-mail: langevelde@jive.nl We present the results of a five year campaign observing 6.7 GHz methanol masers towards a new type of masers. We discuss the origin of elliptically shaped methanol masers in massive star

  4. Competition between vitrification and crystallization of methanol at high pressure

    E-Print Network [OSTI]

    Vos, Willem L.

    Competition between vitrification and crystallization of methanol at high pressure Marco J. P methanol at high pressure up to 33 GPa at room temperature with x-ray diffraction, optical polarization and vitrification is observed when methanol is superpressed beyond the freezing pressure of 3.5 GPa: between 5

  5. Molecular Dynamics of Methanol Monocation (CH3OH+ ) in Strong

    E-Print Network [OSTI]

    Schlegel, H. Bernhard

    Molecular Dynamics of Methanol Monocation (CH3OH+ ) in Strong Laser Fields Bishnu Thapa and H surfaces of methanol neutral, monocation, and singlet and triplet dication were explored using the CBS in the presence of a 2.9 × 1014 W/cm2 800 nm laser field for methanol monocation on the ground state potential

  6. Structure of crystalline methanol at high pressure David R. Allan

    E-Print Network [OSTI]

    Vos, Willem L.

    Structure of crystalline methanol at high pressure David R. Allan Department of Physics structure, including all atomic positions, of methanol at high pressure and room temperature pressure of methanol is 3.5 GPa. In practice however, it is very easy to superpress the liquid phase

  7. Simultaneous observation of water and class I methanol masers toward class II methanol maser sources

    E-Print Network [OSTI]

    Kang, Hyunwoo; Byun, Do-Young; Lee, Seokho; Park, Yong-Sun

    2015-01-01

    We present a simultaneous single-dish survey of 22 GHz water maser and 44 GHz and 95 GHz class I methanol masers toward 77 6.7 GHz class II methanol maser sources, which were selected from the Arecibo methanol maser Galactic plane survey (AMGPS) catalog.Water maser emission is detected in 39 (51%) sources, of which 15 are new detections. Methanol maser emission at 44 GHz and 95 GHz is found in 25 (32%) and 19 (25%) sources, of which 21 and 13 sources are newly detected, respectively. We find 4 high-velocity (> 30 km/s) water maser sources, including 3 dominant blue- or redshifted outflows.The 95 GHz masers always appear with the 44 GHz maser emission. They are strongly correlated with 44 GHz masers in velocity, flux density, and luminosity, while they are not correlated with either water or 6.7 GHz class II methanol masers. The average peak flux density ratio of 95 GHz to 44 GHz masers is close to unity, which is two times higher than previous estimates. The flux densities of class I methanol masers are more ...

  8. Surface Studies of Aqueous Methanol Solutions by Vibrational Broad Bandwidth Sum Frequency Generation Spectroscopy

    E-Print Network [OSTI]

    Surface Studies of Aqueous Methanol Solutions by Vibrational Broad Bandwidth Sum Frequency methanol (CH3OH) and aqueous methanol solutions were investigated using broad bandwidth sum frequency of methanol molecules at the air-liquid interfaces of neat methanol and aqueous methanol solutions. However

  9. Formulation of stable mixtures of diesel fuels with methanol

    SciTech Connect (OSTI)

    Azev, V.S.; Gerasimova, G.N.; Luneva, V.V.

    1986-07-01

    This paper presents an investigation of the possibility of formulating stable blends of diesel fuel and methanol. Two commercial products (diesel fuel L-0.5 and methanol) were used. In studying the influence of hydrocarbon composition on the solubility of methanol, certain individual aromatic hydrocarbons were used: toluene, cumene, and a-methylnaphthalene. It is shown that the most stable formulations are 5% methanol and 0.5% water; 5% methanol, 0.5% water, and 0.25% surfactant. Higher alcohols, particularly butanol, can be used to stabilize blends of methanol with diesel fuel. The butanol/methanol ratio should be no lower than 2/1, and this cannot be justified economically.

  10. Ethanol Demand in United States Gasoline Production

    SciTech Connect (OSTI)

    Hadder, G.R.

    1998-11-24

    The Oak Ridge National Laboratory (OWL) Refinery Yield Model (RYM) has been used to estimate the demand for ethanol in U.S. gasoline production in year 2010. Study cases examine ethanol demand with variations in world oil price, cost of competing oxygenate, ethanol value, and gasoline specifications. For combined-regions outside California summer ethanol demand is dominated by conventional gasoline (CG) because the premised share of reformulated gasoline (RFG) production is relatively low and because CG offers greater flexibility for blending high vapor pressure components like ethanol. Vapor pressure advantages disappear for winter CG, but total ethanol used in winter RFG remains low because of the low RFG production share. In California, relatively less ethanol is used in CG because the RFG production share is very high. During the winter in California, there is a significant increase in use of ethanol in RFG, as ethanol displaces lower-vapor-pressure ethers. Estimated U.S. ethanol demand is a function of the refiner value of ethanol. For example, ethanol demand for reference conditions in year 2010 is 2 billion gallons per year (BGY) at a refiner value of $1.00 per gallon (1996 dollars), and 9 BGY at a refiner value of $0.60 per gallon. Ethanol demand could be increased with higher oil prices, or by changes in gasoline specifications for oxygen content, sulfur content, emissions of volatile organic compounds (VOCS), and octane numbers.

  11. ORIGINAL ARTICLE Utilization of diets containing graded levels of ethanol

    E-Print Network [OSTI]

    ORIGINAL ARTICLE Utilization of diets containing graded levels of ethanol production co to manufacture fuel ethanol (Rosentrater and Muthukumarappan, 2006). In 2008, 174 operating ethanol plants.1 billion liters (RFA, 2009). With this exponential growth in ethanol production, significant quantities

  12. Solubilities of butane, vapor pressures, and densities for benzene + cyclohexane, benzene + methanol, and methanol + cyclohexane solutions at 298 K

    SciTech Connect (OSTI)

    Miyano, Yoshimori (Okayama Univ. of Science (Japan)); Hayduk, W. (Univ. of Ottawa, Ontario (Canada))

    1993-04-01

    In this paper the solubilities of butane at a pressure of 101.3 kPa and a temperature of 298.15 K are presented for three mixed solvent solutions: benzene + methanol, cyclohexane + methanol, and benzene + cyclohexane. The densities and vapor pressures are also reported for these solutions at the same conditions. Whereas the benzene + methanol and cyclohexane + methanol mixtures form azeotropic solutions, they are mutually soluble for all compositions of the two solvents. On the other hand, mixtures of cyclohexane and methanol are not mutually soluble but form two immiscible liquid phases for a significant portion of the composition range, but at a higher temperature also form an azeotropic solution.

  13. Biofuel alternatives to ethanol: pumping the microbial well

    E-Print Network [OSTI]

    Fortman, J.L.

    2011-01-01

    Biofuel alternatives to ethanol: pumping the microbialtechnologies that enable biofuel production. Decades of workstrategy for producing biofuel. Although ethanol currently

  14. Transportation risk assessment for ethanol transport 

    E-Print Network [OSTI]

    Shelton Davis, Anecia Delaine

    2008-10-10

    This research is aimed at assessing the quantitative risks involved with an ethanol pipeline. Pipelines that run from the Midwest, where the vast majority of ethanol is produced, to the target areas where reformulated gasoline is required...

  15. Ethanol Fuel Basics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    have estimated that ethanol and other biofuels could replace 30% or more of U.S. gasoline demand by 2030. More than 95% of U.S. gasoline contains ethanol in a low-level blend to...

  16. Transportation risk assessment for ethanol transport 

    E-Print Network [OSTI]

    Shelton Davis, Anecia Delaine

    2009-05-15

    This research is aimed at assessing the quantitative risks involved with an ethanol pipeline. Pipelines that run from the Midwest, where the vast majority of ethanol is produced, to the target areas where reformulated gasoline is required...

  17. METHANOL AS A TRACER OF FUNDAMENTAL CONSTANTS

    SciTech Connect (OSTI)

    Levshakov, S. A. [A. F. Ioffe Physical-Technical Institute, Saint Petersburg 194021 (Russian Federation); Kozlov, M. G. [Petersburg Nuclear Physics Institute, Gatchina 188300 (Russian Federation); Reimers, D., E-mail: lev@astro.ioffe.rssi.ru, E-mail: mgk@mf1309.spb.edu, E-mail: st2e101@hs.uni-hamburg.de [Hamburger Sternwarte, Universitaet Hamburg, Gojenbergsweg 112, D-21029 Hamburg (Germany)

    2011-09-01

    The methanol molecule CH{sub 3}OH has a complex microwave spectrum with a large number of very strong lines. This spectrum includes purely rotational transitions as well as transitions with contributions of the internal degree of freedom associated with the hindered rotation of the OH group. The latter takes place due to the tunneling of hydrogen through the potential barriers between three equivalent potential minima. Such transitions are highly sensitive to changes in the electron-to-proton mass ratio, {mu} = m{sub e}/m{sub p}, and have different responses to {mu}-variations. The highest sensitivity is found for the mixed rotation-tunneling transitions at low frequencies. Observing methanol lines provides more stringent limits on the hypothetical variation of {mu} than ammonia observation with the same velocity resolution. We show that the best-quality radio astronomical data on methanol maser lines constrain the variability of {mu} in the Milky Way at the level of |{Delta}{mu}/{mu}| < 28 x 10{sup -9} (1{sigma}) which is in line with the previously obtained ammonia result, |{Delta}{mu}/{mu}| < 29 x 10{sup -9} (1{sigma}). This estimate can be further improved if the rest frequencies of the CH{sub 3}OH microwave lines will be measured more accurately.

  18. Conversion of methanol to hydrocarbons III. Methylation, ethylation, and propylation of benzene with methanol

    SciTech Connect (OSTI)

    Kaeding, W.W. (Mobil Chemical Company, Princeton, NJ (USA))

    1988-12-01

    Methanol is converted to hydrocarbons (and water) over HZSM-5 zeolite catalyst in the presence of 1-8M excesses of benzene. Methanol products are primarily aliphatic hydrocarbon gases and C{sub 1} to C{sub 4} aliphatic substituents on the aromatic ring. Methylation of benzene to produce toluene increases as the feed ratio of methanol/benzene decreases. Mild conditions minimize aromatic ring production from methanol. Molar distribution of the methylene group (-CH{sub 2}-) in the product, is tabulated according to carbon number. Methane plus methyl substituents on the aromatic ring measure C{sub 1}; ethane, ethylene, and ethyl ring substituents measure C{sub 2}, etc. At temperatures up to 325 C, methylene distribution in the product is methyl = ethyl > propyl {much gt} butyl. Above 350 C, methyl {much gt} ethyl > propyl. This distribution of the methylene group, under mild conditions, may be a measure of the early production of light olefins, from methanol, within the zeolite pores.

  19. Ethanol's Effect on Grain Supply and Prices

    SciTech Connect (OSTI)

    2008-01-01

    This document provides graphical information about ethanol's effect on grain supply and prices, uses of corn, and grain price trends.

  20. Re-engineering bacteria for ethanol production

    DOE Patents [OSTI]

    Yomano, Lorraine P; York, Sean W; Zhou, Shengde; Shanmugam, Keelnatham; Ingram, Lonnie O

    2014-05-06

    The invention provides recombinant bacteria, which comprise a full complement of heterologous ethanol production genes. Expression of the full complement of heterologous ethanol production genes causes the recombinant bacteria to produce ethanol as the primary fermentation product when grown in mineral salts medium, without the addition of complex nutrients. Methods for producing the recombinant bacteria and methods for producing ethanol using the recombinant bacteria are also disclosed.

  1. U.S. Ethanol Policy: The Unintended

    E-Print Network [OSTI]

    Meagher, Mary

    petroleum and to cut greenhouse gas emissions. A new blend of ethanol and conventional gasoline was to cost- tive, the current blend of E10 (or 10% ethanol) gasoline offers pros and cons. The btu efficiency of a gallon of ethanol is about 40% less than a gallon of conventional gasoline. So, an E10 blend requires 4

  2. Effects of ethanol preservation on otolith microchemistry

    E-Print Network [OSTI]

    Effects of ethanol preservation on otolith microchemistry K. J. HEDGES*, S. A. LUDSIN*§ AND B. J coupled plasma-mass spectrometry was used to examine the effects of exposure time to ethanol (0, 1, 3, 9, 27 and 81 days) and ethanol quality (ACS- v. HPLC- grade) on strontium (Sr) and barium (Ba

  3. Compressed Gas Cylinder Policy

    E-Print Network [OSTI]

    of pressure from a compressed gas cylinder and pose a serious threat to life and property. To minimize risk cylinders to and from a designated work are

  4. Laser Compression of Tantalum /

    E-Print Network [OSTI]

    Lu, Chia-Hui

    2013-01-01

    of this container was filled with aerogel, which acts as aafter laser compression. Aerogel was designed to deceleratein this geometry. The aerogel did not introduce any

  5. Ethanol production by recombinant hosts

    DOE Patents [OSTI]

    Fowler, David E. (Gainesville, FL); Horton, Philip G. (Gainesville, FL); Ben-Bassat, Arie (Gainesville, FL)

    1996-01-01

    Novel plasmids comprising genes which code for the alcohol dehydrogenase and pyruvate decarboxylase are described. Also described are recombinant hosts which have been transformed with genes coding for alcohol dehydrogenase and pyruvate. By virtue of their transformation with these genes, the recombinant hosts are capable of producing significant amounts of ethanol as a fermentation product. Also disclosed are methods for increasing the growth of recombinant hosts and methods for reducing the accumulation of undesirable metabolic products in the growth medium of these hosts. Also disclosed are recombinant host capable of producing significant amounts of ethanol as a fermentation product of oligosaccharides and plasmids comprising genes encoding polysaccharases, in addition to the genes described above which code for the alcohol dehydrogenase and pyruvate decarboxylase. Further, methods are described for producing ethanol from oligomeric feedstock using the recombinant hosts described above. Also provided is a method for enhancing the production of functional proteins in a recombinant host comprising overexpressing an adhB gene in the host. Further provided are process designs for fermenting oligosaccharide-containing biomass to ethanol.

  6. Ethanol production by recombinant hosts

    DOE Patents [OSTI]

    Ingram, Lonnie O. (Gainesville, FL); Beall, David S. (Gainesville, FL); Burchhardt, Gerhard F. H. (Gainesville, FL); Guimaraes, Walter V. (Vicosa, BR); Ohta, Kazuyoshi (Miyazaki, JP); Wood, Brent E. (Gainesville, FL); Shanmugam, Keelnatham T. (Gainesville, FL)

    1995-01-01

    Novel plasmids comprising genes which code for the alcohol dehydrogenase and pyruvate decarboxylase are described. Also described are recombinant hosts which have been transformed with genes coding for alcohol dehydrogenase and pyruvate. By virtue of their transformation with these genes, the recombinant hosts are capable of producing significant amounts of ethanol as a fermentation product. Also disclosed are methods for increasing the growth of recombinant hosts and methods for reducing the accumulation of undesirable metabolic products in the growth medium of these hosts. Also disclosed are recombinant host capable of producing significant amounts of ethanol as a fermentation product of oligosaccharides and plasmids comprising genes encoding polysaccharases, in addition to the genes described above which code for the alcohol dehydrogenase and pyruvate decarboxylase. Further, methods are described for producing ethanol from oligomeric feedstock using the recombinant hosts described above. Also provided is a method for enhancing the production of functional proteins in a recombinant host comprising overexpressing an adhB gene in the host. Further provided are process designs for fermenting oligosaccharide-containing biomass to ethanol.

  7. Ethanol production in recombinant hosts

    DOE Patents [OSTI]

    Ingram, Lonnie O'Neal; Barbosa-Alleyne, Maria D.

    2005-02-01

    The subject invention concerns the transformation of Gram-positive bacteria with heterologous genes which confer upon these microbes the ability to produce ethanol as a fermentation product. Specifically exemplified is the transformation of bacteria with genes, obtainable from Zymomonas mobilis, which encode pyruvate decarboxylase and alcohol dehydrogenase.

  8. LAPPED TRANSFORMS COMPRESSION

    E-Print Network [OSTI]

    de Queiroz, Ricardo L.

    Chapter 6 LAPPED TRANSFORMS FOR IMAGE COMPRESSION Ricardo L. de Queiroz Digital Imaging Technology aspects of lapped transforms and their applications to image compression. It is a subject that has been extensively studied mainly because lapped transforms are closely related to filter banks, wavelets, and time

  9. Activation of catalysts for synthesizing methanol from synthesis gas

    DOE Patents [OSTI]

    Blum, David B. (108 Tall Oaks Dr., Wayne, NJ 07470); Gelbein, Abraham P. (45 Headley Rd., Morristown, NJ 07960)

    1985-01-01

    A method for activating a methanol synthesis catalyst is disclosed. In this method, the catalyst is slurried in an inert liquid and is activated by a reducing gas stream. The activation step occurs in-situ. That is, it is conducted in the same reactor as is the subsequent step of synthesizing methanol from a methanol gas stream catalyzed by the activated catalyst still dispersed in a slurry.

  10. Scalable Communication Trace Compression

    SciTech Connect (OSTI)

    Krishnamoorthy, Sriram; Agarwal, Khushbu

    2010-05-17

    Characterizing the communication behavior of parallel programs through tracing can help understand an application’s characteristics, model its performance, and predict behavior on future systems. However, lossless communication traces can get prohibitively large, causing programmers to resort to variety of other techniques. In this paper, we present a novel approach to lossless communication trace compression. We augment the sequitur compression algorithm to employ it in communication trace compression of parallel programs. We present optimizations to reduce the memory overhead, reduce size of the trace files generated, and enable compression across multiple processes in a parallel program. The evaluation shows improved compression and reduced overhead over other approaches, with up to 3 orders of magnitude improvement for the NAS MG benchmark. We also observe that, unlike existing schemes, the trace files sizes and the memory overhead incurred are less sensitive to, if not independent of, the problem size for the NAS benchmarks.

  11. Fundamentals of Compressed Air Systems

    Office of Energy Efficiency and Renewable Energy (EERE)

    Find out how a compressed air system works and the benefits of optimal compressed air system performance. This initial class demonstrates how to compute the current cost of your plant's compressed...

  12. From CO2 to Methanol via Novel Nanocatalysts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    From CO2 to Methanol via Novel Nanocatalysts Print Researchers have found novel nanocatalysts that lower the barrier to converting carbon dioxide (CO2)-an abundant greenhouse...

  13. Improved Direct Methanol Fuel Cell Stack

    DOE Patents [OSTI]

    Wilson, Mahlon S. (Los Alamos, NM); Ramsey, John C. (Los Alamos, NM)

    2005-03-08

    A stack of direct methanol fuel cells exhibiting a circular footprint. A cathode and anode manifold, tie-bolt penetrations and tie-bolts are located within the circular footprint. Each fuel cell uses two graphite-based plates. One plate includes a cathode active area that is defined by serpentine channels connecting the inlet and outlet cathode manifold. The other plate includes an anode active area defined by serpentine channels connecting the inlet and outlet of the anode manifold, where the serpentine channels of the anode are orthogonal to the serpentine channels of the cathode. Located between the two plates is the fuel cell active region.

  14. Methanol production from eucalyptus wood chips. Attachment IV. Health and safety aspects of the eucalypt biomass to methanol energy system

    SciTech Connect (OSTI)

    Fishkind, H.H.

    1982-06-01

    The basic eucalyptus-to-methanol energy process is described and possible health and safety risks are identified at all steps of the process. The toxicology and treatment for exposure to these substances are described and mitigating measures are proposed. The health and safety impacts and risks of the wood gasification/methanol synthesis system are compared to those of the coal liquefaction and conversion system. The scope of this report includes the health and safety risks of workers (1) in the laboratory and greenhouse, where eucalyptus seedlings are developed, (2) at the biomass plantation, where these seedlings are planted and mature trees harvested, (3) transporting these logs and chips to the refinery, (4) in the hammermill, where the logs and chips will be reduced to small particles, (5) in the methanol synthesis plant, where the wood particles will be converted to methanol, and (6) transporting and dispensing the methanol. Finally, the health and safety risks of consumers using methanol is discussed.

  15. Methanol Observation of IRAS 19312+1950: A Possible New Type of Class I Methanol Masers

    E-Print Network [OSTI]

    Nakashima, Jun-ichi; Salii, Svetlana V; Zhang, Yong; Yung, Bosco H K; Deguchi, Shuji

    2015-01-01

    We report the result of a systematic methanol observation toward IRAS 19312+1950. The properties of the SiO, H2O and OH masers of this object are consistent with those of mass-losing evolved stars, but some other properties are difficult to explain in the standard scheme of stellar evolution in its late stage. Interestingly, a tentative detection of radio methanol lines was suggested toward this object by a previous observation. To date, there are no confirmed detections of methanol emission towards evolved stars, so investigation of this possible detection is important to better understand the circumstellar physical/chemical environment of IRAS 19312+1950. In this study, we systematically observed multiple methanol lines of IRAS 19312+1950 in the lambda=3mm, 7mm, and 13mm bands, and detected 6 lines including 4 thermal lines and 2 class I maser lines. We derived basic physical parameters including kinetic temperature and relative abundances by fitting a radiative transfer model. According to the derived exci...

  16. Structural dynamics of hydrogen bonded methanol oligomers: Vibrational transient hole burning studies of spectral diffusion

    E-Print Network [OSTI]

    Fayer, Michael D.

    Structural dynamics of hydrogen bonded methanol oligomers: Vibrational transient hole burning resolved pump-probe experiments have been conducted on the deuterated hydroxyl stretch of methanol-d in a solution containing 0.8% methanol-d/23% methanol-h in carbon tetrachloride. Methanol-d molecules that both

  17. Ethanol annual report FY 1990

    SciTech Connect (OSTI)

    Texeira, R.H.; Goodman, B.J.

    1991-01-01

    This report summarizes the research progress and accomplishments of the US Department of Energy (DOE) Ethanol from Biomass Program, field managed by the Solar Energy Research Institute, during FY 1990. The report includes an overview of the entire program and summaries of individual research projects. These projects are grouped into the following subject areas: technoeconomic analysis; pretreatment; cellulose conversion; xylose fermentation; and lignin conversion. Individual papers have been indexed separately for inclusion on the data base.

  18. Bioenergy Impacts Â… Cellulosic Ethanol

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:FinancingPetroleum Based Fuels Researchof Energy|Make Fuels andfor its cellulosic ethanol

  19. Alternative Fuels Data Center: Ethanol

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels Data Center Home Page on Digg Find More places toEthanol Printable Version Share

  20. Volume$3, number 3 CHEMICAL. PHYSICS LETTERS 1 Februrf 1978 INTERACTION OF METHANOL WITH RUTHENIUM

    E-Print Network [OSTI]

    Goodman, Wayne

    Volume$3, number 3 CHEMICAL. PHYSICS LETTERS 1 Februrf 1978 INTERACTION OF METHANOL WITH RUTHENIUM of methanol with a clean methods. Methanol dissociates upon adsorption at 300 K and yields Ha(g) and chemisorbed CO as the domiwt

  1. EFFECTS OF METAL-SUPPORT INTERACTIONS ON THE SYNTHESIS OF METHANOL OVER PALLADIUM

    E-Print Network [OSTI]

    Ryndin, Yu A.

    2013-01-01

    on the Synthesis of Methanol over Palladium by Yu. A.ABSTRACT The synthesis of methanol and other products fromThe specific activity for methanol synthesis decreased in

  2. Understanding the effect of modifying elements in supported vanadia bilayered catalysts for methanol oxidation to formaldehyde

    E-Print Network [OSTI]

    Vining, William Collins

    2011-01-01

    Si Figure 1.1. Schematic of methanol oxidation over isolatedSiO 2 catalysts for methanol oxidation, 163-171, Copyright (rate constant at 550 K for methanol oxidation plotted versus

  3. The Arecibo Methanol Maser Galactic Plane Survey--I: Data

    E-Print Network [OSTI]

    Jagadheep D. Pandian; Paul F. Goldsmith; Avinash A. Deshpande

    2007-02-06

    We present the results of an unbiased survey for 6.7 GHz methanol masers in the Galactic plane carried out using the 305 m Arecibo radio telescope. A total of 18.2 square degrees was surveyed with uniform sampling at 35.2 deg methanol masers are clustered, reflecting the formation of massive stars in clusters.

  4. Food for fuel: The price of ethanol

    E-Print Network [OSTI]

    Albino, Dominic K; Bar-Yam, Yaneer

    2012-01-01

    Conversion of corn to ethanol in the US since 2005 has been a major cause of global food price increases during that time and has been shown to be ineffective in achieving US energy independence and reducing environmental impact. We make three key statements to enhance understanding and communication about ethanol production's impact on the food and fuel markets: (1) The amount of corn used to produce the ethanol in a gallon of regular gas would feed a person for a day, (2) The production of ethanol is so energy intensive that it uses only 20% less fossil fuel than gasoline, and (3) The cost of gas made with ethanol is actually higher per mile because ethanol reduces gasoline's energy per gallon.

  5. The Role of Cellulosic Ethanol in Transportation

    SciTech Connect (OSTI)

    Robert M. Neilson, Jr.

    2007-10-01

    Petroleum provides essentially all of the energy used today in the transportation sector. To reduce this dependence on fossil energy, other fuels are beginning to be used, notably ethanol and biodiesel. Almost all fuel ethanol is produced by the conversion of corn grain to starch with subsequent fermentation to ethanol. In 2006, almost 5 billion gallons of fuel ethanol were produced, which used 17% of domestic corn production. The DOE has a goal to displace 30% of motor gasoline demand or 60 billion gallons per year by 2030. To achieve this goal, production of ethanol from lignocellulosic sources (e.g., agricultural residues, forest residues, and dedicated energy crops) is needed. This paper will describe the production of cellulosic ethanol as well as the issues and benefits associated with its production.

  6. Methanol supply and demand issues from a California perspective

    SciTech Connect (OSTI)

    Koyama, K.; Darling, L. (California Energy Commission, Sacramento, CA (US))

    1988-01-01

    This paper reports that despite state policies aimed at reducing high levels of petroleum dependency and air pollution, California relies primarily on petroleum fuels for transportation. As an alternative to petroleum-based fuels, methanol has become increasingly important because of its potential for improving energy security and air quality. A growing body of evidence also suggests that methanol could serve as a toxic substance control by displacing benzene in gasoline. In light of these findings, recent governmental and private-sector activities have been focused on methanol, creating a momentum that has substantially improved the prospects of this fuel for use in the transportation sector. Because this momentum could lead to greater demand for methanol fuel, questions of methanol supply demand, and availability must be addressed.

  7. Image compression technique

    DOE Patents [OSTI]

    Fu, C.Y.; Petrich, L.I.

    1997-03-25

    An image is compressed by identifying edge pixels of the image; creating a filled edge array of pixels each of the pixels in the filled edge array which corresponds to an edge pixel having a value equal to the value of a pixel of the image array selected in response to the edge pixel, and each of the pixels in the filled edge array which does not correspond to an edge pixel having a value which is a weighted average of the values of surrounding pixels in the filled edge array which do correspond to edge pixels; and subtracting the filled edge array from the image array to create a difference array. The edge file and the difference array are then separately compressed and transmitted or stored. The original image is later reconstructed by creating a preliminary array in response to the received edge file, and adding the preliminary array to the received difference array. Filling is accomplished by solving Laplace`s equation using a multi-grid technique. Contour and difference file coding techniques also are described. The techniques can be used in a method for processing a plurality of images by selecting a respective compression approach for each image, compressing each of the images according to the compression approach selected, and transmitting each of the images as compressed, in correspondence with an indication of the approach selected for the image. 16 figs.

  8. Image compression technique

    DOE Patents [OSTI]

    Fu, Chi-Yung (San Francisco, CA); Petrich, Loren I. (Livermore, CA)

    1997-01-01

    An image is compressed by identifying edge pixels of the image; creating a filled edge array of pixels each of the pixels in the filled edge array which corresponds to an edge pixel having a value equal to the value of a pixel of the image array selected in response to the edge pixel, and each of the pixels in the filled edge array which does not correspond to an edge pixel having a value which is a weighted average of the values of surrounding pixels in the filled edge array which do correspond to edge pixels; and subtracting the filled edge array from the image array to create a difference array. The edge file and the difference array are then separately compressed and transmitted or stored. The original image is later reconstructed by creating a preliminary array in response to the received edge file, and adding the preliminary array to the received difference array. Filling is accomplished by solving Laplace's equation using a multi-grid technique. Contour and difference file coding techniques also are described. The techniques can be used in a method for processing a plurality of images by selecting a respective compression approach for each image, compressing each of the images according to the compression approach selected, and transmitting each of the images as compressed, in correspondence with an indication of the approach selected for the image.

  9. Innovative Breakthrough Demonstrated for Biological Ethanol Production...

    Broader source: Energy.gov (indexed) [DOE]

    nearly doubled bio-ethanol productivity, increased conversion yields, and minimized microbial contaminants. The process showed increased productivity and efficiency, therefore...

  10. High ethanol producing derivatives of Thermoanaerobacter ethanolicus

    DOE Patents [OSTI]

    Ljungdahl, Lars G. (Athens, GA); Carriera, Laura H. (Athens, GA)

    1983-01-01

    Derivatives of the newly discovered microorganism Thermoanaerobacter ethanolicus which under anaerobic and thermophilic conditions continuously ferment substrates such as starch, cellobiose, glucose, xylose and other sugars to produce recoverable amounts of ethanol solving the problem of fermentations yielding low concentrations of ethanol using the parent strain of the microorganism Thermoanaerobacter ethanolicus are disclosed. These new derivatives are ethanol tolerant up to 10% (v/v) ethanol during fermentation. The process includes the use of an aqueous fermentation medium, containing the substrate at a substrate concentration greater than 1% (w/v).

  11. High ethanol producing derivatives of Thermoanaerobacter ethanolicus

    DOE Patents [OSTI]

    Ljungdahl, L.G.; Carriera, L.H.

    1983-05-24

    Derivatives of the newly discovered microorganism Thermoanaerobacter ethanolicus which under anaerobic and thermophilic conditions continuously ferment substrates such as starch, cellobiose, glucose, xylose and other sugars to produce recoverable amounts of ethanol solving the problem of fermentations yielding low concentrations of ethanol using the parent strain of the microorganism Thermoanaerobacter ethanolicus are disclosed. These new derivatives are ethanol tolerant up to 10% (v/v) ethanol during fermentation. The process includes the use of an aqueous fermentation medium, containing the substrate at a substrate concentration greater than 1% (w/v).

  12. Emissions from ethanol and LPG fueled vehicles

    SciTech Connect (OSTI)

    Pitstick, M.E.

    1992-12-31

    This paper addresses the environmental concerns of using neat ethanol and liquified petroleum gas (LPG) as transportation fuels in the US Low-level blends of ethanol (10%) with gasoline have been used as fuels in the US for more than a decade, but neat ethanol (85% or more) has only been used extensively in Brazil. LPG, which consists mostly of propane, is already used extensively as a vehicle fuel in the US, but its use has been limited primarily to converted fleet vehicles. Increasing US interest in alternative fuels has raised the possibility of introducing neat ethanol vehicles into the market and expanding the number of LPG vehicles. Use of such vehicles and increased production and consumption of fuel ethanol and LPG will undoubtedly have environmental impacts. If the impacts are determined to be severe, they could act as barriers to the introduction of neat ethanol and LPG vehicles. Environmental concerns include exhaust and evaporative emissions and their impact on ozone formation and global warming, toxic emissions from fuel combustion and evaporation, and agricultural emissions from production of ethanol. The paper is not intended to be judgmental regarding the overall attractiveness of ethanol or LPG compared to other transportation fuels. The environmental concerns are reviewed and summarized, but the only conclusion reached is that there is no single concern that is likely to prevent the introduction of neat ethanol fueled vehicles or the increase in LPG fueled vehicles.

  13. Emissions from ethanol and LPG fueled vehicles

    SciTech Connect (OSTI)

    Pitstick, M.E.

    1992-01-01

    This paper addresses the environmental concerns of using neat ethanol and liquified petroleum gas (LPG) as transportation fuels in the US Low-level blends of ethanol (10%) with gasoline have been used as fuels in the US for more than a decade, but neat ethanol (85% or more) has only been used extensively in Brazil. LPG, which consists mostly of propane, is already used extensively as a vehicle fuel in the US, but its use has been limited primarily to converted fleet vehicles. Increasing US interest in alternative fuels has raised the possibility of introducing neat ethanol vehicles into the market and expanding the number of LPG vehicles. Use of such vehicles and increased production and consumption of fuel ethanol and LPG will undoubtedly have environmental impacts. If the impacts are determined to be severe, they could act as barriers to the introduction of neat ethanol and LPG vehicles. Environmental concerns include exhaust and evaporative emissions and their impact on ozone formation and global warming, toxic emissions from fuel combustion and evaporation, and agricultural emissions from production of ethanol. The paper is not intended to be judgmental regarding the overall attractiveness of ethanol or LPG compared to other transportation fuels. The environmental concerns are reviewed and summarized, but the only conclusion reached is that there is no single concern that is likely to prevent the introduction of neat ethanol fueled vehicles or the increase in LPG fueled vehicles.

  14. Ethanol: Producting Food, Feed, and Fuel

    Broader source: Energy.gov [DOE]

    At the August 7, 2008 joint quarterly Web conference of DOE's Biomass and Clean Cities programs, Todd Sneller (Nebraska Ethanol Board) discussed the food versus fuel issue.

  15. Natural and Anthropogenic Ethanol Sources in North America and Potential Atmospheric Impacts of Ethanol

    E-Print Network [OSTI]

    Mlllet, Dylan B.

    S1 Natural and Anthropogenic Ethanol Sources in North America and Potential Atmospheric Impacts of Ethanol Fuel Use Dylan B. Millet*,1 , Eric Apel2 , Daven K. Henze3 , Jason Hill1 , Julian D. Marshall1 INFORMATION Supporting Information contains a total of 12 pages, 1 table, and 7 figures. 1. AIRBORNE ETHANOL

  16. Natural and Anthropogenic Ethanol Sources in North America and Potential Atmospheric Impacts of Ethanol Fuel Use

    E-Print Network [OSTI]

    Mlllet, Dylan B.

    Natural and Anthropogenic Ethanol Sources in North America and Potential Atmospheric Impacts of Ethanol Fuel Use Dylan B. Millet,*, Eric Apel, Daven K. Henze,§ Jason Hill, Julian D. Marshall, Hanwant B-Chem chemical transport model to constrain present-day North American ethanol sources, and gauge potential long

  17. Low temperature catalyst system for methanol production

    DOE Patents [OSTI]

    Sapienza, R.S.; Slegeir, W.A.; O'Hare, T.E.

    1984-04-20

    This patent discloses a catalyst and process useful at low temperatures (150/sup 0/C) and preferably in the range 80 to 120/sup 0/C used in the production of methanol from carbon monoxide and hydrogen. The catalyst components are used in slurry form and comprise (1) a complex reducing agent derived from the component structure NaH-ROH-M(OAc)/sub 2/ where M is selected from the group consisting of Ni, Pd, and Co and R is a lower alkyl group containing 1 to 6 carbon atoms and (2) a metal carbonyl of a group VI (Mo, Cr, W) metal. For the first component, Nic is preferred (where M = Ni and R = tertiary amyl). For the second component, Mo(CO)/sub 6/ is preferred. The mixture is subjected to a conditioning or activating step under temperature and pressure, similar to the parameters given above, to afford the active catalyst.

  18. Low temperature catalysts for methanol production

    DOE Patents [OSTI]

    Sapienza, R.S.; Slegeir, W.A.; O'Hare, T.E.; Mahajan, D.

    1986-09-30

    A catalyst and process useful at low temperatures (below about 160 C) and preferably in the range 80--120 C used in the production of methanol from carbon monoxide and hydrogen are disclosed. The catalyst is used in slurry form and comprises a complex reducing agent derived from the component structure NaH--RONa-M(OAc)[sub 2] where M is selected from the group consisting of Ni, Pd, and Co and R is a lower alkyl group containing 1--6 carbon atoms. This catalyst is preferably used alone but is also effective in combination with a metal carbonyl of a group VI (Mo, Cr, W) metal. The preferred catalyst precursor is Nic (where M = Ni and R = tertiary amyl). Mo(CO)[sub 6] is the preferred metal carbonyl if such component is used. The catalyst is subjected to a conditioning or activating step under temperature and pressure, similar to the parameters given above, to afford the active catalyst.

  19. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite for methanol synthesis

    DOE Patents [OSTI]

    Tierney, John W. (Pittsburgh, PA); Wender, Irving (Pittsburgh, PA); Palekar, Vishwesh M. (Pittsburgh, PA)

    1993-01-01

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  20. Observational constraints on the global atmospheric budget of ethanol

    E-Print Network [OSTI]

    2010-01-01

    global atmospheric budget of ethanol V. Naik 1,2,* , A. M.nitrate formation from ethanol-fueled ve- hicular emissions,A. : Ambient concentrations of ethanol and methyl tert-butyl

  1. Effects of ethanol and reactive species on Hepatitis C virus

    E-Print Network [OSTI]

    Seronello, Scott E.

    2010-01-01

    Barlow, M. ; Choi, J. (2010) Ethanol and both endogenous andT. , and Choi, J. (2010) Ethanol enhances hepatitis C virusthe levels of NADH like ethanol but generates acetone

  2. Catalytic Process for the Conversion of Coal-derived Syngas to Ethanol

    SciTech Connect (OSTI)

    James Spivery; Doug Harrison; John Earle; James Goodwin; David Bruce; Xunhau Mo; Walter Torres; Joe Allison Vis Viswanathan; Rick Sadok; Steve Overbury; Viviana Schwartz

    2011-07-29

    The catalytic conversion of coal-derived syngas to C{sub 2+} alcohols and oxygenates has attracted great attention due to their potential as chemical intermediates and fuel components. This is particularly true of ethanol, which can serve as a transportation fuel blending agent, as well as a hydrogen carrier. A thermodynamic analysis of CO hydrogenation to ethanol that does not allow for byproducts such as methane or methanol shows that the reaction: 2 CO + 4 H{sub 2} {yields} C{sub 2}H{sub 5}OH + H{sub 2}O is thermodynamically favorable at conditions of practical interest (e.g,30 bar, {approx}< 250 C). However, when methane is included in the equilibrium analysis, no ethanol is formed at any conditions even approximating those that would be industrially practical. This means that undesired products (primarily methane and/or CO{sub 2}) must be kinetically limited. This is the job of a catalyst. The mechanism of CO hydrogenation leading to ethanol is complex. The key step is the formation of the initial C-C bond. Catalysts that are selective for EtOH can be divided into four classes: (a) Rh-based catalysts, (b) promoted Cu catalysts, (c) modified Fischer-Tropsch catalysts, or (d) Mo-sulfides and phosphides. This project focuses on Rh- and Cu-based catalysts. The logic was that (a) Rh-based catalysts are clearly the most selective for EtOH (but these catalysts can be costly), and (b) Cu-based catalysts appear to be the most selective of the non-Rh catalysts (and are less costly). In addition, Pd-based catalysts were studied since Pd is known for catalyzing CO hydrogenation to produce methanol, similar to copper. Approach. The overall approach of this project was based on (a) computational catalysis to identify optimum surfaces for the selective conversion of syngas to ethanol; (b) synthesis of surfaces approaching these ideal atomic structures, (c) specialized characterization to determine the extent to which the actual catalyst has these structures, and (d) testing at realistic conditions (e.g., elevated pressures) and differential conversions (to measure true kinetics, to avoid deactivation, and to avoid condensable concentrations of products in the outlet gas).

  3. Diversified Ethanol | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTIONRobertsdale, Alabama (UtilityInstrumentsArea (DOE GTP)DisplacementTudorOpen EnergyPage EditEthanol

  4. Orion Ethanol | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to:Newberg, Oregon:OGEProjects/DefinitionsOrchidx AmericaOrion Ethanol

  5. Ethanol Ventures | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX E LISTStar2-0057-EA Jump to:ofEnia SpA Jump to:EnergyEthanol Ventures Place: London,

  6. Dakota Ethanol | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTIONRobertsdale, Alabama (UtilityInstruments Inc Jump to:67-2006-12DabbrookAssociation Jump to:Ethanol

  7. Alternative Fuel Tool Kit How to Implement: Ethanol (E85)

    E-Print Network [OSTI]

    is a renewable alternative transportation fuel blend of gasoline and ethanol. Ethanol (C2H5OH, a.k.a. ethyl, and Dispensing E85 and Other Ethanol-Gasoline Blends" by the US Department of Energy ( US DOE).1,2 The dominant ethanol/gasoline blends in the United States are up to 10% ethanol (E10) and up to 83% ethanol (E85). More

  8. Vehicle Certification Test Fuel and Ethanol Flex Fuel Quality...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Vehicle Certification Test Fuel and Ethanol Flex Fuel Quality Vehicle Certification Test Fuel and Ethanol Flex Fuel Quality Breakout Session 2: Frontiers and Horizons Session 2-B:...

  9. Infrastructure Requirements for an Expanded Fuel Ethanol Industry

    SciTech Connect (OSTI)

    Reynolds, Robert E.

    2002-01-15

    This report provides technical information specifically related to ethanol transportation, distribution, and marketing issues. This report required analysis of the infrastructure requirements for an expanded ethanol industry.

  10. Review of Recent Pilot Scale Cellulosic Ethanol Demonstration...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Review of Recent Pilot Scale Cellulosic Ethanol Demonstration Review of Recent Pilot Scale Cellulosic Ethanol Demonstration Opening Plenary Session: Celebrating Successes-The...

  11. Effects of Intermediate Ethanol Blends on Legacy Vehicles and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Effects of Intermediate Ethanol Blends on Legacy Vehicles and Small Non-Road Engines, Report 1 Updated Feb 2009 Effects of Intermediate Ethanol Blends on Legacy Vehicles and...

  12. Novel Vertimass Catalyst for Conversion of Ethanol and Other...

    Office of Environmental Management (EM)

    Novel Vertimass Catalyst for Conversion of Ethanol and Other Alcohols into Fungible Gasoline, Jet, and Diesel Fuel Blend Stocks Novel Vertimass Catalyst for Conversion of Ethanol...

  13. Thermochemical Ethanol via Indirect Gasification and Mixed Alcohol...

    Office of Environmental Management (EM)

    Ethanol via Indirect Gasification and Mixed Alcohol Synthesis of Lignocellulosic Biomass Thermochemical Ethanol via Indirect Gasification and Mixed Alcohol Synthesis of...

  14. Reaction Rates and Catalysts in Ethanol Production (1 Activity...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reaction Rates and Catalysts in Ethanol Production (1 Activity) Reaction Rates and Catalysts in Ethanol Production (1 Activity) Below is information about the student activity...

  15. Report to Congress: Dedicated Ethanol Pipeline Feasability Study...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Report to Congress: Dedicated Ethanol Pipeline Feasability Study - Energy Independence and Security Act of 2007 Section 243 Report to Congress: Dedicated Ethanol Pipeline...

  16. Dispensing Equipment Testing With Mid-Level Ethanol/Gasoline...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dispensing Equipment Testing With Mid-Level EthanolGasoline Test Fluid Dispensing Equipment Testing With Mid-Level EthanolGasoline Test Fluid The National Renewable Energy...

  17. Systems biology analysis of Zymomonas mobilis ZM4 ethanol stress...

    Office of Scientific and Technical Information (OSTI)

    Systems biology analysis of Zymomonas mobilis ZM4 ethanol stress responses Citation Details In-Document Search Title: Systems biology analysis of Zymomonas mobilis ZM4 ethanol...

  18. Biofuel alternatives to ethanol: pumping the microbial well

    E-Print Network [OSTI]

    Fortman, J. L.

    2010-01-01

    2007) Cellulosic ethanol: biofuel researchers prepare toBiofuel alternatives to ethanol: pumping the microbial welltechnologies that enable biofuel production. Decades of work

  19. Impact of Ethanol Blending on U.S. Gasoline Prices

    SciTech Connect (OSTI)

    Not Available

    2008-11-01

    This study assesses the impact of ethanol blending on gasoline prices in the US today and the potential impact of ethanol on gasoline prices at higher blending concentrations.

  20. Market penetration of biodiesel and ethanol 

    E-Print Network [OSTI]

    Szulczyk, Kenneth Ray

    2007-09-17

    that for the ranges studied, gasoline prices have a major impact on aggregate ethanol production but only at low prices. At higher prices, one runs into a capacity constraint that limits expansion on the capacity of ethanol production. Aggregate biodiesel production...

  1. Ethanol Production: Energy, Economic, and Environmental Losses

    E-Print Network [OSTI]

    Patzek, Tadeusz W.

    of biomass convert solar energy into plant material, but this conversion requires suitable soil, nutrients.1% of the solar energy. Two early studies by the U.S. Department of Energy (USDOE) con- cerning ethanol productionEthanol Production: Energy, Economic, and Environmental Losses David Pimentel, Tad Patzek

  2. Ethanol production using engineered mutant E. coli

    DOE Patents [OSTI]

    Ingram, Lonnie O. (Gainesville, FL); Clark, David P. (Carbondale, IL)

    1991-01-01

    The subject invention concerns novel means and materials for producing ethanol as a fermentation product. Mutant E. coli are transformed with a gene coding for pyruvate decarboxylase activity. The resulting system is capable of producing relatively large amounts of ethanol from a variety of biomass sources.

  3. Outlook for Biomass Ethanol Production and Demand

    Reports and Publications (EIA)

    2000-01-01

    This paper presents a midterm forecast for biomass ethanol production under three different technology cases for the period 2000 to 2020, based on projections developed from the Energy Information Administration's National Energy Modeling System. An overview of cellulose conversion technology and various feedstock options and a brief history of ethanol usage in the United States are also presented.

  4. Coadsorption of toluene and methanol on HZSM-5 zeolites

    SciTech Connect (OSTI)

    Mirth, G.; Lercher, J.A. (Technische Univ. Wien (Austria))

    1991-05-02

    Coadsorption of toluene and methanol on HZSM-5 at 308 and 473 K was studied to investigate adsorption complexes formed in the zeolite pores prior to alkylation reactions. Methanol is adsorbed in the form of methoxonium ions at the Si-O{sup {minus}}-Al groups of the zeolite, and toluene is hydrogen bonded to these methoxonium ions. The thermal stability of the coadsorption complex, however, is low, as concluded from temperature-programmed desorption (TPD) measurements. Toluene desorbs prior to methanol, dimethyl ether in minor amounts is the only reaction product detected in the gas phase during TPD.

  5. Novel Materials for High Efficiency Direct Methanol Fuel Cells

    SciTech Connect (OSTI)

    Carson, Stephen; Mountz, David; He, Wensheng; Zhang, Tao

    2013-12-31

    Direct methanol fuel cell membranes were developed using blends of different polyelectrolytes with PVDF. The membranes showed complex relationships between polyelectrolyte chemistry, morphology, and processing. Although the PVDF grade was found to have little effect on the membrane permselectivity, it does impact membrane conductivity and methanol permeation values. Other factors, such as varying the polyelectrolyte polarity, using varying crosslinking agents, and adjusting the equivalent weight of the membranes impacted methanol permeation, permselectivity, and areal resistance. We now understand, within the scope of the project work completed, how these inter-related performance properties can be tailored to achieve a balance of performance.

  6. Isentropic Compression of Argon

    SciTech Connect (OSTI)

    H. Oona; J.C. Solem; L.R. Veeser, C.A. Ekdahl; P.J. Rodriquez; S.M. Younger; W. Lewis; W.D. Turley

    1997-08-01

    We are studying the transition of argon from an insulator to a conductor by compressing the frozen gas isentropically to pressures at which neighboring atomic orbitals overlap sufficiently to allow some electron motion between atoms. Argon and the other rare gases have closed electron shells and therefore remain montomic, even when they solidify. Their simple structure makes it likely that any measured change in conductivity is due to changes in the atomic structure, not in molecular configuration. As the crystal is compressed the band gap closes, allowing increased conductivity. We have begun research to determine the conductivity at high pressures, and it is our intention to determine the compression at which the crystal becomes a metal.

  7. Dual-fueling turbocharged diesels with ethanol

    SciTech Connect (OSTI)

    Cruz, J.M.; Rotz, C.A.; Watson, D.H.

    1982-09-01

    Spray addition and carburetion methods were tested for dual-fueling a turbocharged, 65 kW diesel tractor. Approximately 30 percent of the fuel energy for the tractor was supplied by spraying ethanol into the intake air and about 46 percent by carburetion with little affect on the engine thermal efficiency. Further substitution of diesel fuel with ethanol was limited by knock. As the amount of ethanol fed into the engine was increased, ignition apparently changed from the steady burning process which normally occurs in a diesel engine to a rapid explosion which caused knock. The best fuel for the spray approach was a 50 percent ethanol/water solution and with the carburetor it was an 80 percent ethanol/water solution.

  8. Dual-fueling turbocharged diesels with ethanol

    SciTech Connect (OSTI)

    Cruz, J.M.; Rotz, C.A.; Watson, D.H.

    1982-09-01

    Spray addition and carburetion methods were tested for dual-fueling a turbocharged, 65 kW diesel tractor. Approximately 30 percent of the fuel energy for the tractor was supplied by spraying ethanol into the intake air and about 46 percent by carburetion with little affect on the engine thermal efficiency. Further substitution of diesel fuel with ethanol was limited by knock. As the amount of ethanol fed into the engine was increased, ignition apparently changed from the steady burning process which normally occurs in a diesel engine to a rapid explosion which caused knock. The best fuel for the spray approach was a 50 percent ethanol/water solution and with the carburetor it was an 80 percent ethanol/water solution. (Refs. 6).

  9. Commercial-Scale Demonstration of the Liquid Phase Methanol (LOMEOH(TM)) Process

    SciTech Connect (OSTI)

    1996-03-31

    The Liquid Phase Methanol (LPMEOEP") Demonstration Project at K.ingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L, P. (the Partnership). The LPMEOHY Process Demonstration Unit is being built at a site located at the Eastman Chemical Company (Eastman) complex in Kingsport. On 4 October 1994, Air Products and Chemicals, Inc. (Air Products) and signed the agreements that would form the Partnership, secure the demonstration site, and provide the financial commitment and overall project management for the project. These partnership agreements became effective on 15 March 1995, when DOE authorized the commencement of Budget Period No. 2 (Mod. AO08 to the Cooperative Agreement). The Partnership has subcontracted with Air Products to provide the overall management of the project, and to act as the primary interface with DOE. As subcontractor to the Partnership, Air Products will also provide the engineering design, procurement, construction, and commissioning of the LPMEOHTM Process Demonstration Unit, and will provide the technical and engineering supervision needed to conduct the operational testing program required as part of the project. As subcontractor to Air Products, Eastman will be responsible for operation of the LPMEOHTM Process Demonstration Unit, and for the interconnection and supply of synthesis gas, utilities, product storage, and other needed sewices. The project involves the construction of an 80,000 gallons per day (260 tons-per-day (TPD)) methanol unit utilizing coal-derived synthesis gas fi-om Eastman's integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOHTM process is ideally suited for directly processing gases produced by modern day coal gasifiers. Originally tested at a small 3,200 gallons per day, DOE-owned experimental unit in LaPorte, Texas, the technology provides several improvements essential for the economic coproduction of methanol and electricity directly from gasified coal. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface, protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates.

  10. Mechanistic Studies of Methanol Oxidation to Formaldehyde on Isolated Vanadate Sites Supported on MCM-48

    E-Print Network [OSTI]

    Bell, Alexis T.

    Mechanistic Studies of Methanol Oxidation to Formaldehyde on Isolated Vanadate Sites Supported-1462 ReceiVed: August 16, 2006; In Final Form: October 10, 2006 The mechanism of methanol oxidation. Methanol reacts reversibly, at a ratio of approximately 1 methanol per V, with one V-O-Si to produce both V

  11. Theoretical characterization of the hydrogen-bond interaction of diacetamide with water and methanol

    E-Print Network [OSTI]

    Nguyen, Minh Tho

    and methanol Minh Tho Nguyen, Natalie Leroux and The re` se Zeegers-Huyskens* Department of Chemistry formed from interaction of diacetamide with water and methanol. In both water and methanol complexes/6-31G** level being [44 kJ mol~1 for the water complex and [48 kJ mol~1 for the methanol complex

  12. Author's personal copy Modeling of a passive DMFC operating with neat methanol

    E-Print Network [OSTI]

    Zhao, Tianshou

    Author's personal copy Modeling of a passive DMFC operating with neat methanol W.W. Yang, T.S. Zhao 2011 Keywords: Fuel cells Direct methanol fuel cells Neat methanol Mass transport Model a b s t r a c t A mathematical model is developed to simulate the fundamental transport phenomena in a passive direct methanol

  13. 6.7 GHZ METHANOL MASERS: PROPERTIES, ASSOCIATIONS AND TRACERS OF GALACTIC

    E-Print Network [OSTI]

    Richardson Jr., James E.

    6.7 GHZ METHANOL MASERS: PROPERTIES, ASSOCIATIONS AND TRACERS OF GALACTIC STRUCTURE A Dissertation Jagadheep Dhanasekara Pandian ALL RIGHTS RESERVED #12;6.7 GHZ METHANOL MASERS: PROPERTIES, ASSOCIATIONS transition of methanol is the strongest of methanol masers, and is the second strongest maser transition ever

  14. Ultrafast Carrier Dynamics in Exfoliated and Functionalized Calcium Niobate Nanosheets in Water and Methanol

    E-Print Network [OSTI]

    Osterloh, Frank

    and Methanol Elizabeth C. Carroll, Owen C. Compton, Dorte Madsen, Frank E. Osterloh, and Delmar S. Larsen-order kinetics on a sub-nanosecond time scale that depended on the nanosheet size. Methanol was used and methanol solutions. Methanol is known as an efficient sacrificial electron donor for layered metal oxide

  15. THE METHANOL MASER EMISSION IN W51 C.J. PHILLIPS1

    E-Print Network [OSTI]

    van Langevelde, Huib Jan

    THE METHANOL MASER EMISSION IN W51 C.J. PHILLIPS1 and H.J. VAN LANGEVELDE2 1 CSIRO; E-mail: chris.7-GHz methanol maser emission towards W51. In the W51 Main region, the bulk of the methanol is offset from an UCHII region. This probably indicates the methanol emission arises at the interface

  16. Is Methanol the Transportation Fuel of the Future?

    E-Print Network [OSTI]

    Sperling, Daniel; DeLuchi, Mark A.

    1989-01-01

    in the U.S. were coal, oil shale, and biomass. Natural gas (produced from coal and oil shale, methanol produced frommethanol was rated below oil shale and other coal-liquid

  17. Is Methanol the Transportation Fuel of the Future?

    E-Print Network [OSTI]

    Sperling, Daniel; DeLuchi, Mark A.

    1989-01-01

    Gasoline and diesel fuel distributors would lose control of fuel marketing if natural gas, currently distributed by a network of pipeline-transmission companies,gasoline a far more promising alternative than methanol. They argued that oil companies

  18. Low temperature catalysts for methanol production

    DOE Patents [OSTI]

    Sapienza, Richard S. (1 Miller Ave., Shoreham, NY 11786); Slegeir, William A. (7 Florence Rd., Hampton Bays, NY 11946); O'Hare, Thomas E. (11 Geiger Pl., Huntington Station, NY 11746); Mahajan, Devinder (14 Locust Ct., Selden, NY 11784)

    1986-01-01

    A catalyst and process useful at low temperatures (below about 160.degree. C.) and preferably in the range 80.degree.-120.degree. C. used in the production of methanol from carbon monoxide and hydrogen is disclosed. The catalyst is used in slurry form and comprises a complex reducing agent derived from the component structure NaH--RONa--M(OAc).sub.2 where M is selected from the group consisting of Ni, Pd, and Co and R is a lower alkyl group containing 1-6 carbon atoms. This catalyst is preferably used alone but is also effective in combination with a metal carbonyl of a group VI (Mo, Cr, W) metal. The preferred catalyst precursor is Nic (where M=Ni and R=tertiary amyl). Mo(CO).sub.6 is the preferred metal carbonyl if such component is used. The catalyst is subjected to a conditioning or activating step under temperature and pressure, similar to the parameters given above, to afford the active catalyst.

  19. Low temperature catalysts for methanol production

    DOE Patents [OSTI]

    Sapienza, R.S.; Slegeir, W.A.; O'Hare, T.E.; Mahajan, D.

    1985-03-12

    A catalyst and process useful at low temperatures (below about 160/sup 0/C) and preferably in the range 80 to 120/sup 0/C used in the production of methanol from carbon monoxide and hydrogen is disclosed. The catalyst is used in slurry form and comprises a complex reducing agent derived from the component structure NaH-RONa-M(OAc)/sub 2/ where M is selected from the group consisting of Ni, Pd, and Co and R is a lower alkyl group containing 1 to 6 carbon atoms. This catalyst is preferably used alone but is also effective in combination with a metal carbonyl of a group VI (Mo, Cr, W) metal. The preferred catalyst precursor is Nic (where M = Ni and R = tertiary amyl). Mo(CO)/sub 6/ is the preferred metal carbonyl if such component is used. The catalyst is subjected to a conditioning or activating step under temperature and pressure, similar to the parameters given above, to afford the active catalyst.

  20. Low temperature catalysts for methanol production

    DOE Patents [OSTI]

    Sapienza, R.S.; Slegeir, W.A.; O'Hare, T.E.; Mahajan, D.

    1986-10-28

    A catalyst and process useful at low temperatures (below about 160 C) and preferably in the range 80--120 C used in the production of methanol from carbon monoxide and hydrogen are disclosed. The catalyst is used in slurry form and comprises a complex reducing agent derived from the component structure NaH--RONa-M(OAc)[sub 2] where M is selected from the group consisting of Ni, Pd, and Co and R is a lower alkyl group containing 1-6 carbon atoms. This catalyst is preferably used alone but is also effective in combination with a metal carbonyl of a group VI (Mo, Cr, W) metal. The preferred catalyst precursor is NiC (where M = Ni and R = tertiary amyl). Mo(CO)[sub 6] is the preferred metal carbonyl if such component is used. The catalyst is subjected to a conditioning or activating step under temperature and pressure, similar to the parameters given above, to afford the active catalyst.

  1. Commercial-scale demonstration of the Liquid Phase Methanol process. Technical progress report number 8, April 1--June 30, 1996

    SciTech Connect (OSTI)

    1996-12-31

    The project involves the construction of an 80,000 gallon per day (260 tons per day (TPD)) methanol unit utilizing coal-derived synthesis gas from Eastman`s integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} process is ideally suited for directly processing gases produced by modern-day coal gasifiers. Originally tested at a small (10 TPD), DOE-owned experimental unit in LaPorte, Texas, the technology provides several improvements essential for the economic coproduction of methanol and electricity directly from gasified coal. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface, protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates. At the Eastman complex, the technology is being integrated with existing coal-gasifiers. A carefully developed test plan will allow operations at Eastman to simulate electricity demand load-following in coal-based IGCC facilities. The operations will also demonstrate the enhanced stability and heat dissipation of the conversion process, its reliable on/off operation, and its ability to produce methanol as a clean liquid fuel without additional upgrading.

  2. Ethanol Production, Distribution, and Use: Discussions on Key Issues (Presentation)

    SciTech Connect (OSTI)

    Harrow, G.

    2008-05-14

    From production to the environment, presentation discusses issues surrounding ethanol as a transportation fuel.

  3. Ethanol Pathways in the 2050 North American Transportation Futures Study

    SciTech Connect (OSTI)

    2009-01-18

    A paper discussing the various ethanol pathways in the 2050 North American Transportation Futures Study

  4. Ethanol Tolerance Caused by slowpoke Induction in Drosophila

    E-Print Network [OSTI]

    Atkinson, Nigel

    Ethanol Tolerance Caused by slowpoke Induction in Drosophila Roshani B. Cowmeadow, Harish R in the ethanol response. Caenorhabditis elegans carrying mutations in this gene have altered ethanol sensitivity and Drosophila mutant for this gene are unable to acquire rapid tolerance to ethanol or anesthetics

  5. Photochemical reduction of carbon dioxide to methanol using ZnS microcrystallite as a photocatalyst in the presence of methanol dehydrogenase

    SciTech Connect (OSTI)

    Kuwabata, Susumu; Nishida, Kazufumi; Tsuda, Ryo; Inoue, Hiroshi; Yoneyama, Hiroshi (Osaka Univ. (Japan). Dept. of Applied Chemistry)

    1994-06-01

    Photoinduced reduction of formate to methanol has been achieved using ZnS microcrystalline colloid which contained formate, methanol dehydrogenase (MDH), pyrroloquinoline quinone (PQQ) as an electron mediator for MDH, and 2-propanol. This reaction was combined with photoreduction of carbon dioxide to formate on the ZnS microcrystallite which had already been reported to provide a new photosynthetic route for production of methanol from carbon dioxide. The production of methanol showed a saturation tendency when it was accumulated to 0.25 mmol dm[sup [minus]3], probably due to oxidation of the produced methanol at MDH or on the ZnS photocatalyst or both. The concentration of PQQ influenced the amount of formate production but not the methanol production. The quantum efficiency obtained at 280 nm for the reduction of carbon dioxide to methanol was 5.9%, which is the highest value that has ever been reported for the photochemical reduction of carbon dioxide to methanol.

  6. Environmental analysis of biomass-ethanol facilities

    SciTech Connect (OSTI)

    Corbus, D.; Putsche, V.

    1995-12-01

    This report analyzes the environmental regulatory requirements for several process configurations of a biomass-to-ethanol facility. It also evaluates the impact of two feedstocks (municipal solid waste [MSW] and agricultural residues) and three facility sizes (1000, 2000, and 3000 dry tons per day [dtpd]) on the environmental requirements. The basic biomass ethanol process has five major steps: (1) Milling, (2) Pretreatment, (3) Cofermentation, (4) Enzyme production, (5) Product recovery. Each step could have environmental impacts and thus be subject to regulation. Facilities that process 2000 dtpd of MSW or agricultural residues would produce 69 and 79 million gallons of ethanol, respectively.

  7. Efficiency Considerations of Diesel Premixed Charge Compression...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Considerations of Diesel Premixed Charge Compression Ignition Combustion Efficiency Considerations of Diesel Premixed Charge Compression Ignition Combustion Poster...

  8. The feasibility of ethanol production in Texas 

    E-Print Network [OSTI]

    Herbst, Brian Keith

    2003-01-01

    been done in Texas. Previous studies are typically for a generic location and only looked at ethanol production from corn. This study looks at four different plant sizes in three different regions using corn and grain sorghum. This study incorporates...

  9. QER- Comment of ND Ethanol Council

    Broader source: Energy.gov [DOE]

    To whom it may concern, Attached please find comments from the North Dakota Ethanol Council regarding infrastructure constraints in preparation for the OER Public Meeting, which will be held in Bismarck, N.D., on August 8. Sincerely, Deana Wies

  10. Treatment of biomass to obtain ethanol

    DOE Patents [OSTI]

    Dunson, Jr., James B. (Newark, DE); Elander, Richard T. (Evergreen, CO); Tucker, III, Melvin P. (Lakewood, CO); Hennessey, Susan Marie (Avondale, PA)

    2011-08-16

    Ethanol was produced using biocatalysts that are able to ferment sugars derived from treated biomass. Sugars were obtained by pretreating biomass under conditions of high solids and low ammonia concentration, followed by saccharification.

  11. Random Operator Compressions

    E-Print Network [OSTI]

    Stephen Ng; Meg Walters

    2014-09-19

    Let $A$ be a Hermitian operator of order $n$. We show that for $k\\leq n$ sufficiently large, the eigenvalues of a compression of $A$ to a $k$-dimensional subspace are almost the same for all subspaces. We prove this result using the methods introduced in a paper by Chatterjee and Ledoux on eigenvalues of principle submatrices. We show that by choosing an appropriate Markov chain, the methods of Chatterjee and Ledoux can be applied to give a more general result on operator compressions. As an additional application of this method, we prove concentration of measure of the length of the longest increasing subsequence of a random walk distributed under the invariant measure for the asymmetric exclusion process.

  12. Compression Technology and Needs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:FinancingPetroleum Based Fuels|ProgramsLake Paiute Reservation | Department ofCompressed Hydrogen®

  13. Energy Utilization in Fermentation Ethanol Production 

    E-Print Network [OSTI]

    Easley, C. E.

    1987-01-01

    valid consideration when high grade fuel such as petroleum or natural gas is the energy source for the ethanol plant. But for plants running on coal or other solid fuels, ethanol production can be considered to be a form of "coal liquefaction.... The three main steps are cooking, which opens the starch bundles (called gelatinization) making them accessible for enzymatic action; liquefaction, in which large starch molecules are cut into smaller segments by enzymes, thus making the starch...

  14. High Speed/ Low Effluent Process for Ethanol

    SciTech Connect (OSTI)

    M. Clark Dale

    2006-10-30

    n this project, BPI demonstrated a new ethanol fermentation technology, termed the High Speed/ Low Effluent (HS/LE) process on both lab and large pilot scale as it would apply to wet mill and/or dry mill corn ethanol production. The HS/LE process allows very rapid fermentations, with 18 to 22% sugar syrups converted to 9 to 11% ethanol ‘beers’ in 6 to 12 hours using either a ‘consecutive batch’ or ‘continuous cascade’ implementation. This represents a 5 to 8X increase in fermentation speeds over conventional 72 hour batch fermentations which are the norm in the fuel ethanol industry today. The ‘consecutive batch’ technology was demonstrated on a large pilot scale (4,800 L) in a dry mill corn ethanol plant near Cedar Rapids, IA (Xethanol Biofuels). The pilot demonstrated that 12 hour fermentations can be accomplished on an industrial scale in a non-sterile industrial environment. Other objectives met in this project included development of a Low Energy (LE) Distillation process which reduces the energy requirements for distillation from about 14,000 BTU/gal steam ($0.126/gal with natural gas @ $9.00 MCF) to as low as 0.40 KW/gal electrical requirements ($0.022/gal with electricity @ $0.055/KWH). BPI also worked on the development of processes that would allow application of the HS/LE fermentation process to dry mill ethanol plants. A High-Value Corn ethanol plant concept was developed to produce 1) corn germ/oil, 2) corn bran, 3) ethanol, 4) zein protein, and 5) nutritional protein, giving multiple higher value products from the incoming corn stream.

  15. Role of water activity in ethanol fermentations

    SciTech Connect (OSTI)

    Jones, R.P.; Greenfield, P.F.

    1986-01-01

    A separate role for water activity in the conversion of sugars to ethanol by two strains of yeast is identified. During fermentation of both single and mixed sugar substrates, the water activity was shown to remain constant during the logarithmic growth phase. This is despite the changes in concentration of substrates and production, the constancy reflecting the fact that the greater influence of ethanol on the solution activity is counterbalanced, in the early stages of the fermentation, by its low yield. The end of the log phase of growth coincides with the start of a period of gradually decreasing water activity. For the more ethanol-tolerant strain UQM66Y, growth was found to cease at a constant value of water activity while that for the less tolerant strain UQM70Y depended on both ethanol concentration and water activity. It is argued that water activity is a more appropriate variable than ethanol concentration for describing some of the nonspecific inhibitory effects apparent in ethanol fermentations. A straightforward method for the calculation of water activity during such fermentations based on the use of solution osmolarity is presented.

  16. Methanol fuel vehicle demonstration: Exhaust emission testing. Final report

    SciTech Connect (OSTI)

    Hyde, J.D. [New York State Dept. of Environmental Conservation, Albany, NY (US). Automotive Emissions Lab.

    1993-07-01

    Ford Motor Company converted four stock 1986 Ford Crown Victoria sedans to methanol flexible fuel vehicles (FFVs). During 143,108 operational miles from 1987 to 1990, the FFVs underwent more than 300 dynamometer driving tests to measure exhaust emissions, catalytic activity, fuel economy, acceleration, and driveability with gasoline and methanol blend fuels. Dynamometer driving tests included the Federal Test Procedure (FTP), the Highway Fuel Economy Test, and the New York City Cycle. Exhaust emission measurements included carbon dioxide, carbon monoxide (CO), nitrogen oxides (NO{sub x}), non- oxygenated hydrocarbons, organic material hydrocarbon equivalent (OMHCE), formaldehyde, and methanol. Catalytic activity was based on exhaust emissions data from active and inactive catalysts. OMHCE, CO, and NO{sub x} were usually lower with M85 (85% methanol, 15% gasoline) than with gasoline for both active and inactive catalysts when initial engine and catalyst temperatures were at or near normal operating temperatures. CO was higher with M85 than with gasoline when initial engine and catalyst temperatures were at or near ambient temperature. Formaldehyde and methanol were higher with M85. Active catalyst FTP OMHCE, CO, and NO{sub x} increased as vehicle mileage increased, but increased less with M85 than with gasoline. Energy based fuel economy remained almost constant with changes in fuel composition and vehicle mileage.

  17. Bifunctional Anode Catalysts for Direct Methanol Fuel Cells

    SciTech Connect (OSTI)

    Rossmeisl, Jan; Ferrin, Peter A.; Tritsaris, Georgios A.; Nilekar, Anand U.; Koh, Shirlaine; Bae, Sang Eun; Brankovic, Stanko R.; Strasser, Peter; Mavrikakis, Manos

    2012-06-13

    Using the binding energy of OH* and CO* on close-packed surfaces as reactivity descriptors, we screen bulk and surface alloy catalysts for methanol electro-oxidation activity. Using these two descriptors, we illustrate that a good methanol electro-oxidation catalyst must have three key properties: (1) the ability to activate methanol, (2) the ability to activate water, and (3) the ability to react off surface intermediates (such as CO* and OH*). Based on this analysis, an alloy catalyst made up of Cu and Pt should have a synergistic effect facilitating the activity towards methanol electro-oxidation. Using these two reactivity descriptors, a surface PtCu3 alloy is proposed to have the best catalytic properties of the Pt–Cu model catalysts tested, similar to those of a Pt–Ru bulk alloy. To validate the model, experiments on a Pt(111) surface modified with different amounts of Cu adatoms are performed. Adding Cu to a Pt(111) surface increases the methanol oxidation current by more than a factor of three, supporting our theoretical predictions for improved electrocatalysts.

  18. Sulfur removal from diesel fuel-contaminated methanol.

    SciTech Connect (OSTI)

    Lee, S. H. D.; Kumar, R.; Krumpelt, M.; Chemical Engineering

    2002-03-01

    Methanol is considered to be a potential on-board fuel for fuel cell-powered vehicles. In current distribution systems for liquid fuels used in the transportation sector, commodity methanol can occasionally become contaminated with the sulfur in diesel fuel or gasoline. This sulfur would poison the catalytic materials used in fuel reformers for fuel cells. We tested the removal of this sulfur by means of ten activated carbons (AC) that are commercially available. Tests were conducted with methanol doped with 1 vol.% grade D-2 diesel fuel containing 0.29% sulfur, which was present essentially as 33-35 wt.% benzothiophenes (BTs) and 65-67 wt.% dibenzothiophenes (DBT). In general, coconut shell-based carbons activated by high-temperature steam were more effective at sulfur removal than coal-based carbons. Equilibrium sorption data showed linear increase in sulfur capture with the increase of sulfur concentration in methanol. Both types of carbons had similar breakthrough characteristics, with the dynamic sorption capacity of each being about one-third of its equilibrium sorption capacity. Results of this study suggest that a fixed-bed sorber of granular AC can be used, such as in refueling stations, for the removal of sulfur in diesel fuel-contaminated methanol.

  19. HD Applications of Significantly Downsized SI Engines Using Alcohol DI for Knock Avoidance

    Broader source: Energy.gov [DOE]

    Direct injection of a second fuel (ethanol or methanol) is explored as a means of avoiding knock in turbocharged, high-compression ratio spark-ignited engines that could replace diesels in certain vocational applications.

  20. Clustering Dynamics in Water/Methanol Mixtures: A Nuclear Magnetic Resonance Study at 205 K < T < 295 K

    E-Print Network [OSTI]

    Stanley, H. Eugene

    Clustering Dynamics in Water/Methanol Mixtures: A Nuclear Magnetic Resonance Study at 205 K functional groups in water/methanol mixtures at different methanol molar fractions (XMeOH ) 0, 0.04, 0.1, 0 in the mixtures, at all the methanol molar fractions, are faster than those of pure water and methanol because

  1. PROCESS DEVELOPMENT STUDIES ON THE BIOCONVERSION OF CELLULOSE AND PRODUCTION OF ETHANOL

    E-Print Network [OSTI]

    Wilke, Charles R.

    2011-01-01

    60,700 ETHANOL RECOVERY Dist. Column CondenserF2 Steam Exchanger Ethanol Absorber 10 ft. diameter. 38Cellulose and Production of Ethanol," Progress Report, LBL-

  2. Length of Stay Following Trauma is not Affected by Ethnicity When Controlled for Ethanol Intoxication

    E-Print Network [OSTI]

    Mangum, Craig; LoVecchio, Frank; Mathieson, Kathleen

    2007-01-01

    When Controlled for Ethanol Intoxication Craig Mangum, MD;properly controlled for ethanol and drug intoxication. Wepatients, controlling for ethanol intoxication. Methods:

  3. Brain reward deficits accompany withdrawal (hangover) from acute ethanol in rats

    E-Print Network [OSTI]

    Schulteis, Gery; Liu, Jian

    2006-01-01

    stimulation reward: effects of ethanol. Alcohol Clin Exp Resstimulus produced by ethanol withdrawal. J Pharmacol Expthe "anxiogenic" response to ethanol withdrawal in the rat.

  4. PILOT PLANT STUDIES OF THE BIOCONVERSION OF CELLULOSE AND PRODUCTION OF ETHANOL

    E-Print Network [OSTI]

    Wilke, C.R.

    2010-01-01

    5 EthanolBazua, D.C. and C.R. Wilke, "Ethanol Effects on the Kineticsto the Production of Ethanol, LBL-5963. (Submitted to

  5. PROCESS DEVELOPMENT STUDIES ON THE BIOCONVERSION OF CELLULOSE AND PRODUCTION OF ETHANOL

    E-Print Network [OSTI]

    Wilke, C.R.

    2011-01-01

    BIOCONVERSION TO SUGARS AND ETHANOL BERKELEY PROGRAM--JulyXylose Fermentation to Ethanol (a) (b) Fusarium oxysporum (OF CELLULOSE AND PRODUCTION OF ETHANOL under auspices of

  6. PROCESS DEVELOPMENT STUDIES ON THE BIOCONVERSION OF CELLULOSE AND PRODUCTION OF ETHANOL

    E-Print Network [OSTI]

    Wilke, Charles R.

    2012-01-01

    13 Javier Perez I II. ETHANOL FERMENTATION STUDIES A. B.Development Studies of Ethanol Production--------------- 19of Cellulose and Production of Ethanol." (June 1979) and (b)

  7. PROCESS DEVELOPMENT STUDIES ON THE BIOCONVERSION OF CELLULOSE AND PRODUCTION OF ETHANOL

    E-Print Network [OSTI]

    Wilke, C.R.

    2011-01-01

    EthanolOf Cellulose And Production Of Ethanol I Charles R. WilkeCELLULOSE AND PRODUCTION OF ETHANOL under auspices of U.S.

  8. Process of concentrating ethanol from dilute aqueous solutions thereof

    DOE Patents [OSTI]

    Oulman, Charles S. [Ames, IA; Chriswell, Colin D. [Slater, IA

    1981-07-07

    Relatively dilute aqueous solutions of ethanol are concentrated by passage through a bed of a crystalline silica polymorph, such as silicalite, to adsorb the ethanol with residual dilute feed in contact with the bed, which is displaced by passing concentrated aqueous ethanol through the bed without displacing the adsorbed ethanol. A product concentrate is then obtained by removing the adsorbed ethanol from the bed together with at least a portion of the concentrated aqueous ethanol used as the displacer liquid. This process permits ethanol to be concentrated from dilute fermentation beers, which may contain from 6 to 10% ethanol, to obtain a concentrate product at very low energy cost having an ethanol concentration in excess of 95%, such as a concentration of from 98 to 99.5%.

  9. Perovskite anode electrocatalysis for direct methanol fuel cells

    SciTech Connect (OSTI)

    White, J.H.; Sammells, A.F. (Eltron Research, Inc., Boulder, CO (United States))

    1993-08-01

    This investigation explores direct methanol fuel cells incorporating perovskite anode electrocatalysts. Preliminary electrochemical performance was addressed following incorporation of electrocatalysts into polymer electrolyte (Nafion 417) fuel cells. Perovskite electrocatalysts demonstrating activity towards direct methanol oxidation during cyclic voltammetry measurements included, respectively, SrRu[sub 0.5]Pt[sub 0.5]O[sub 3], SrRu[sub 0.5]Pd[sub 0.5]O[sub 3], SrPdO[sub 3], SmCoO[sub 3], SrRuO[sub 3], La[sub 0.8]Ce[sub 0.2]CoC[sub 3],SrCo[sub 0.5]Ti[sub 0.5]O[sub 3], and La[sub 0.8]Sr[sub 0.2]CoO[sub 3] where SrRu[sub 0.5]Pt[sub 0.5]P[sub 3] gave methanol oxidation currents up to 28 mA/cm[sup 2] at 0.45 V vs. SCE. Correlations were found between electrocatalyst solid-state and thermodynamic parameters corresponding to, respectively, molecular electronic polarizability, the optical dielectric constant, the perovskite spin-only magnetic moment, the number of d-electrons in perovskite A and B lattice sites, and the average metal-oxygen binding energy for the perovskite lattice, and corresponding fuel cell performance. This may have future merit for the prediction of new electrocatalyst family members for promoting direct methanol oxidation. Methanol diffusion from anode to cathode compartments appears to be a major obstacle to the development of polymer electrolyte methanol fuel cells.

  10. Avalanches in wood compression

    E-Print Network [OSTI]

    Tero Mäkinen; Amandine Miksic; Markus Ovaska; Mikko J. Alava

    2015-06-15

    Wood is a multi-scale material exhibiting a complex viscoplastic response. We study avalanches in small wood samples in compression. "Woodquakes" measured by acoustic emission are surprisingly similar to earthquakes and crackling noise in rocks and laboratory tests on brittle materials. Both the distributions of event energies and of waiting (silent) times follow power-laws. The stress- strain response exhibits clear signatures of localization of deformation to "weak spots" or softwood layers, as identified using Digital Image Correlation. Even though material structure-dependent localization takes place, the avalanche behavior remains scale-free.

  11. Injector spray characterization of methanol in reciprocating engines

    SciTech Connect (OSTI)

    Dodge, L.; Naegeli, D.

    1994-06-01

    This report covers a study that addressed cold-starting problems in alcohol-fueled, spark-ignition engines by using fine-spray port-fuel injectors to inject fuel directly into the cylinder. This task included development and characterization of some very fine-spray, port-fuel injectors for a methanol-fueled spark-ignition engine. After determining the spray characteristics, a computational study was performed to estimate the evaporation rate of the methanol fuel spray under cold-starting and steady-state conditions.

  12. Environmental information volume: Liquid Phase Methanol (LPMEOH{trademark}) project

    SciTech Connect (OSTI)

    1996-05-01

    The purpose of this project is to demonstrate the commercial viability of the Liquid Phase Methanol Process using coal-derived synthesis gas, a mixture of hydrogen and carbon monoxide. This report describes the proposed actions, alternative to the proposed action, the existing environment at the coal gasification plant at Kingsport, Tennessee, environmental impacts, regulatory requirements, offsite fuel testing, and DME addition to methanol production. Appendices include the air permit application, solid waste permits, water permit, existing air permits, agency correspondence, and Eastman and Air Products literature.

  13. An Indirect Route for Ethanol Production

    SciTech Connect (OSTI)

    Eggeman, T.; Verser, D.; Weber, E.

    2005-04-29

    The ZeaChem indirect method is a radically new approach to producing fuel ethanol from renewable resources. Sugar and syngas processing platforms are combined in a novel way that allows all fractions of biomass feedstocks (e.g. carbohydrates, lignins, etc.) to contribute their energy directly into the ethanol product via fermentation and hydrogen based chemical process technologies. The goals of this project were: (1) Collect engineering data necessary for scale-up of the indirect route for ethanol production, and (2) Produce process and economic models to guide the development effort. Both goals were successfully accomplished. The projected economics of the Base Case developed in this work are comparable to today's corn based ethanol technology. Sensitivity analysis shows that significant improvements in economics for the indirect route would result if a biomass feedstock rather that starch hydrolyzate were used as the carbohydrate source. The energy ratio, defined as the ratio of green energy produced divided by the amount of fossil energy consumed, is projected to be 3.11 to 12.32 for the indirect route depending upon the details of implementation. Conventional technology has an energy ratio of 1.34, thus the indirect route will have a significant environmental advantage over today's technology. Energy savings of 7.48 trillion Btu/yr will result when 100 MMgal/yr (neat) of ethanol capacity via the indirect route is placed on-line by the year 2010.

  14. Effects of Age on Pavlovian Autoshaping of Ethanol Drinking in Non-Deprived Rats

    E-Print Network [OSTI]

    Tomie, Arthur; Mohamed, Walaa M.; Pohorecky, Larissa A.

    2005-01-01

    Differential effects of ethanol on motor coordination into the motor-impairing effects of ethanol (Silveri & Spear,the present study. Ethanol’s effects on motor impairment are

  15. Development of a bench scale test to evaluate lubricants for use with methanol-fueled engines

    SciTech Connect (OSTI)

    Shah, R.; Klaus, E.; Duda, J.L.

    1996-10-01

    In methanol-fueled diesel engines, the crankcase lubricant is used to lubricate both the engine and the fuel injector system. Crankcase lubricants including some designed for methanol-fueled engines are not completely compatible with the methanol fuel. In order to test the effect of methanol extraction on diesel engine lubricant performance, two extraction protocols were developed: one to simulate the fuel injector (1000 parts of methanol to one part of lubricant) and the other to simulate an extreme case of methanol contamination in the crank-case (one part of methanol to five parts of lubricant). The extracted samples of the lubricant were stripped to remove the methanol. The samples were then evaluated for changes in oxidative stability and lubricity. 12 refs., 3 figs., 8 tabs.

  16. Supplementary Information for Methanol as a sensitive probe for spatial and temporal variations of the

    E-Print Network [OSTI]

    Supplementary Information for Methanol as a sensitive probe for spatial and temporal variations.757 0.68(5) Table I. Methanol (12 CH16 3 OH) maser transitions and accurate rest frequencies taken from

  17. An Investigation of Different Methods of Fabricating Membrane Electrode Assemblies for Methanol Fuel Cells

    E-Print Network [OSTI]

    Hall, Kwame (Kwame J.)

    2009-01-01

    Methanol fuel cells are electrochemical conversion devices that produce electricity from methanol fuel. The current process of fabricating membrane electrode assemblies (MEAs) is tedious and if it is not sufficiently ...

  18. R&D Strategies for Compressed, Cryo-Compressed and Cryo-Sorbent...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    R&D Strategies for Compressed, Cryo-Compressed and Cryo-Sorbent Hydrogen Storage Technologies Workshops R&D Strategies for Compressed, Cryo-Compressed and Cryo-Sorbent Hydrogen...

  19. Ethanol from biomass: A status report

    SciTech Connect (OSTI)

    Walker, R.

    1996-12-31

    Programmatic and technical activities of SWAN Biomass, a company formed by Amoco Corporation and Stone & Webster, to convert non-grain biomass material to ethanol, are highlighted in this presentation. The potential ethanol markets identified are: (1) fuel oxygenate and octane additive, and (2) waste reduction in the agricultural and forestry industries and in municipal waste streams. Differences in the SWAN process from that used in corn-based ethanol facilities include more intense pretreatment of lignocellulosic biomass, different enzymes, hydrolysis and fermentation of sugar polymers is performed in the same vessel, and a typical solid residue of lignin. The major market and technical risks have been assessed as being manageable. 8 figs., 8 tabs.

  20. Novel Approach to Advanced Direct Methanol Fuel Cell Anode Catalysts (Presentation)

    SciTech Connect (OSTI)

    Dinh, H.; Gennett, T.

    2010-06-11

    This presentation is a summary of a Novel Approach to Advanced Direct Methanol Fuel Cell Anode Catalysts.

  1. Fuel-Cycle energy and emission impacts of ethanol-diesel blends in urban buses and farming tractors.

    SciTech Connect (OSTI)

    Wang, M.; Saricks, C.; Lee, H.

    2003-09-11

    About 2.1 billion gallons of fuel ethanol was used in the United States in 2002, mainly in the form of gasoline blends containing up to 10% ethanol (E10). Ethanol use has the potential to increase in the U.S. blended gasoline market because methyl tertiary butyl ether (MTBE), formerly the most popular oxygenate blendstock, may be phased out owing to concerns about MTBE contamination of the water supply. Ethanol would remain the only viable near-term option as an oxygenate in reformulated gasoline production and to meet a potential federal renewable fuels standard (RFS) for transportation fuels. Ethanol may also be blended with additives (co-solvents) into diesel fuels for applications in which oxygenation may improve diesel engine emission performance. Numerous studies have been conducted to evaluate the fuel-cycle energy and greenhouse gas (GHG) emission effects of ethanol-gasoline blends relative to those of gasoline for applications in spark-ignition engine vehicles (see Wang et al. 1997; Wang et al. 1999; Levelton Engineering et al. 1999; Shapouri et al. 2002; Graboski 2002). Those studies did not address the energy and emission effects of ethanol-diesel (E-diesel or ED) blends relative to those of petroleum diesel fuel in diesel engine vehicles. The energy and emission effects of E-diesel could be very different from those of ethanol-gasoline blends because (1) the energy use and emissions generated during diesel production (so-called ''upstream'' effects) are different from those generated during gasoline production; and (2) the energy and emission performance of E-diesel and petroleum diesel fuel in diesel compression-ignition engines differs from that of ethanol-gasoline blends in spark-ignition (Otto-cycle-type) engine vehicles. The Illinois Department of Commerce and Community Affairs (DCCA) commissioned Argonne National Laboratory to conduct a full fuel-cycle analysis of the energy and emission effects of E-diesel blends relative to those of petroleum diesel when used in the types of diesel engines that will likely be targeted first in the marketplace. This report documents the results of our study. The draft report was delivered to DCCA in January 2003. This final report incorporates revisions by the sponsor and by Argonne.

  2. Direct Methanol Fuel Cell Experimental and Model Validation Study

    E-Print Network [OSTI]

    Wang, Chao-Yang

    Direct Methanol Fuel Cell Experimental and Model Validation Study M. Mench, J. Scott, S. Thynell boundary Fuel cell performance Current density distribution measurements Conclusions #12;3 Method, flow rate, species inlet and fuel cell temperature, and humidity. Transparent polycarbonate windows

  3. Discovery of two new methanol masers in NGC 7538

    E-Print Network [OSTI]

    M. Pestalozzi; V. Minier; F. Motte; J. Conway

    2006-01-20

    Context: NGC7538 is known to host a 6.7 and 12.2GHz methanol maser cospatial with a Ultra Compact (UC) HII region, IRS1. Aims: We report on the serendipitous discovery of two additional 6.7GHz methanol masers in the same region, not associated with IRS1. Methods: Interferometry maser positions are compared with recent single-dish and interferometry continuum observations. Results: The positions of the masers agree to high accuracy with the 1.2mm continuum peak emission in NGC7538 IRS9 and NGC7538 S. This clear association is also confirmed by the positional agreement of the masers with existing high resolution continuum observations at cm and/or mm wavelengths. Conclusions: Making use of the established strong relation between methanol masers and high-mass star formation, we claim that we have accurately positioned the high-mass protostars within the regions where they are detected. The variety of objects hosting a 6.7GHz methanol maser in NGC7538 shows that this emission probably traces different evolutionary stages within the protostellar phase.

  4. Romania program targets methanol and Fischer-Tropsch research

    SciTech Connect (OSTI)

    Not Available

    1987-03-01

    Currently, the chemical organic industry, the petrochemical and engine fuels industry in Romania are entirely based on hydrocarbons from oil. To reduce the oil dependence of this sector and to ensure the stipulated growth rate of 8-9%, research and development programs have been set up with a view to the diversification of raw materials. In research on hydrocarbons from alcohol conversion, three process variants are known, i.e. olefins from methanol, gasolines from methanol and a combined gasolines and aromatic hydrocarbons from methanol. The Romanian process of methanol conversion to hydrocarbons is very flexible, with all the variants mentioned being carried out in the same plant by modifying the catalysts. In research on hydrocarbons from synthesis gas a modern process is being developed for gasification of brown coal in a fluidized bed, under pressure, in the presence of oxygen and water vapors. In the field of carbon oxide hydrogenation, studies have been carried out on selective Fischer-Tropsch processes in which the reaction products are high value hydrocarbon fractions.

  5. Complete Quantitative online Analysis of Methanol Electrooxidation Prod-ucts via Electron Impact and Electrospray Ionization Mass Spectrometry

    E-Print Network [OSTI]

    Pfeifer, Holger

    1 Complete Quantitative online Analysis of Methanol Electrooxidation Prod- ucts via Electron Impact for application in energy re- lated electrocatalysis is demonstrated using continuous methanol oxidation over

  6. State-level workshops on ethanol for transportaton

    SciTech Connect (OSTI)

    Graf, Angela

    2004-01-01

    The Ethanol Workshop Series (EWS) was intended to provide a forum for interest groups to gather and discuss what needs to be accomplished to facilitate ethanol production in-state using local biomass resources.

  7. U.S. Ethanol Policy: The Unintended Consequences 

    E-Print Network [OSTI]

    Griffin, James M.; Soto, Maricio Cifuentes

    2012-01-01

    The Energy Independence and Security Act of 2007 (EISA) mandated a steep rise in domestic ethanol production. The goals were to ease dependency on imported petroleum and to cut greenhouse gas emissions. A new blend of ethanol and conventional...

  8. Investigation of the Photocatalytic Degradation of Ethanol and Acetone 

    E-Print Network [OSTI]

    Liu, Y.; Ding, B.; Dong, S.

    2006-01-01

    In-situ transmission Fourier-transform infrared spectroscopy has been used to study the photocatalytic oxidation of acetone, ethanol and the interaction between acetone and ethanol. Compared with the degradation of acetone alone, it cannot...

  9. Advancing Cellulosic Ethanol for Large Scale Sustainable Transportation

    E-Print Network [OSTI]

    Wyman, C

    2007-01-01

    all but one energy source: petroleum – We use more petroleumMetrics for Ethanol Petroleum in/Energy out Fossil energyMetrics for Ethanol Petroleum in/Energy out Fossil energy

  10. A role for glutathione, independent of oxidative stress, in the developmental toxicity of methanol

    SciTech Connect (OSTI)

    Siu, Michelle T.; Shapiro, Aaron M.; Wiley, Michael J.; Wells, Peter G.

    2013-12-15

    Oxidative stress and reactive oxygen species (ROS) have been implicated in the teratogenicity of methanol (MeOH) in rodents, both in vivo and in embryo culture. We explored the ROS hypothesis further in vivo in pregnant C57BL/6J mice. Following maternal treatment with a teratogenic dose of MeOH, 4 g/kg via intraperitoneal (ip) injection on gestational day (GD) 12, there was no increase 6 h later in embryonic ROS formation, measured by 2?,7?-dichlorodihydrofluorescin diacetate (DCFH-DA) fluorescence, despite an increase observed with the positive control ethanol (EtOH), nor was there an increase in embryonic oxidatively damaged DNA, quantified as 8-oxo-2?-deoxyguanosine (8-oxodG) formation. MeOH teratogenicity (primarily ophthalmic anomalies, cleft palate) also was not altered by pre- and post-treatment with varying doses of the free radical spin trapping agent alpha-phenyl-N-tert-butylnitrone (PBN). In contrast, pretreatment with L-buthionine-(S,R)-sulfoximine (BSO), an inhibitor of glutathione (GSH) synthesis, depleted maternal hepatic and embryonic GSH, and enhanced some new anomalies (micrognathia, agnathia, short snout, fused digits, cleft lip, low set ears), but not the most common teratogenic effects of MeOH (ophthalmic anomalies, cleft palate) in this strain. These results suggest that ROS did not contribute to the teratogenic effects of MeOH in this in vivo mouse model, in contrast to results in embryo culture from our laboratory, and that the protective effect of GSH in this model may arise from its role as a cofactor for formaldehyde dehydrogenase in the detoxification of formaldehyde. - Highlights: • In vivo, a free radical scavenger did not block methanol (MeOH) teratogenesis. • MeOH did not increase embryonic reactive oxygen species formation or DNA oxidation. • MeOH teratogenesis was enhanced by glutathione (GSH) depletion. • GSH may protect as the cofactor for formaldehyde dehydrogenase (ADH3). • Formaldehyde may be a ROS-independent proximate teratogenic species in vivo.

  11. Alternative Fuels Data Center: Ethanol Vehicle Emissions

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels Data Center Home Page on Digg FindPortsas aEthanol Benefits andFuelingEthanol

  12. Three-Dimensional Simulations of Liquid Feed Direct Methanol Wenpeng Liu*,a

    E-Print Network [OSTI]

    Three-Dimensional Simulations of Liquid Feed Direct Methanol Fuel Cells Wenpeng Liu*,a and Chao that performance and design of a liquid feed direct methanol fuel cell DMFC is controlled not only by electrochemical kinetics and methanol crossover but also by water transport and by their complex interactions

  13. Molecular Hydrogen from Methanol Maser Sources { Out ow from the Earliest Stage of Star Formation?

    E-Print Network [OSTI]

    Burton, Michael

    Molecular Hydrogen from Methanol Maser Sources { Out ow from the Earliest Stage of Star Formation in its natal molecular cloud. The strong methanol maser transition 5 1 { 6 0 A + at 6.7 GHz has also been that methanol maser emission usually occurs in massive star forming regions but away from the UCHII regions

  14. PoS(IXEVNSymposium)036 Mapping the Milky Way structure with methanol and

    E-Print Network [OSTI]

    Brunthaler, Andreas

    PoS(IXEVNSymposium)036 Mapping the Milky Way structure with methanol and water masers Luca VLBA and VERA results in measuring trigonometric parallaxes of methanol and water maser sourcesS(IXEVNSymposium)036 Mapping the Milky Way structure with methanol and water masers Luca Moscadelli 1. Introduction

  15. PoS(IXEVNSymposium)039 EVN observations of the methanol masers in Cep A

    E-Print Network [OSTI]

    van Langevelde, Huib Jan

    PoS(IXEVNSymposium)039 EVN observations of the methanol masers in Cep A Karl Torstensson Leiden observations of the 6.7 GHz methanol maser in the high mass star-forming re- gion Cepheus A. The maser emission field of the methanol masers shows an infall sig- nature rather than a rotation signature. We present

  16. Discovery of molecular hydrogen line emission associated with methanol maser emission

    E-Print Network [OSTI]

    Ashley, Michael C. B.

    Discovery of molecular hydrogen line emission associated with methanol maser emission J.-K. Lee March 9 A B S T R AC T We report the discovery of H2 line emission associated with 6.67-GHz methanol emission was found associated with an ultracompact H II region IRAS 14567­5846 and isolated methanol maser

  17. Performance modeling and cell design for high concentration methanol fuel cells

    E-Print Network [OSTI]

    Chapter 50 Performance modeling and cell design for high concentration methanol fuel cells C. E The direct methanol fuel cell (DMFC) has become a lead- ing contender to replace the lithium-ion (Li density of liquid methanol (CH3OH) fuel is 4800 Wh l-1 , whereas the theoretical energy density of Li

  18. Mechanism of O2 Activation and Methanol Production by (Di(2-pyridyl)methanesulfonate)PtII

    E-Print Network [OSTI]

    Goddard III, William A.

    Mechanism of O2 Activation and Methanol Production by (Di(2- pyridyl)methanesulfonate)PtII Me observed for the SN2 functionalization to form methanol by two isomeric (dpms)PtIV Me(OH)2 complexes, one conversion of methane to methanol at low temper- ature is crucial for transportation of shale gas produced

  19. Department of Energy and Mineral Engineering Spring 2012 BP Methanol Separation

    E-Print Network [OSTI]

    Demirel, Melik C.

    PENNSTATE Department of Energy and Mineral Engineering Spring 2012 BP ­ Methanol Separation issues in the well heads. To counteract this problem, methanol is injected into the produced water stream at the well site. Methanol, however, is toxic to humans, animals, and plants, and must be removed before

  20. Electronic spectroscopy of intermediates involved in the conversion of methane to methanol by FeO

    E-Print Network [OSTI]

    Metz, Ricardo B.

    Electronic spectroscopy of intermediates involved in the conversion of methane to methanol by Fe.1063/1.1448489 I. INTRODUCTION The direct oxidation of methane to an easily transport- able liquid such as methanol process and as the simplest model for alkane oxidation.1,2 Although no direct, efficient methane­methanol

  1. A New Reference Correlation for the Viscosity of Methanol Hong Wei Xiang,a...

    E-Print Network [OSTI]

    Magee, Joseph W.

    A New Reference Correlation for the Viscosity of Methanol Hong Wei Xiang,a... Arno Laesecke for the viscosity of methanol is presented that is valid over the entire fluid region, including vapor, liquid coefficient is developed from experimental data and applied to methanol. The high-density contribution

  2. Quantifying global terrestrial methanol emissions using1 observations from the TES satellite sensor2

    E-Print Network [OSTI]

    Meskhidze, Nicholas

    1 Quantifying global terrestrial methanol emissions using1 observations from the TES Figure S1. December-January-Febuary (DJF, top) and June-July-August (JJA, bottom) biogenic3 methanol 1 Figure S4. Regions employed for quantifying terrestrial methanol fluxes (red) and for2

  3. Electrochimica Acta 52 (2007) 43174324 Porous current collectors for passive direct methanol fuel cells

    E-Print Network [OSTI]

    Zhao, Tianshou

    2007-01-01

    Electrochimica Acta 52 (2007) 4317­4324 Porous current collectors for passive direct methanol fuel methanol fuel cell (DMFC) with its cathode current collector made of porous metal foam was investigated did the cell having the conventional perforated-plate current collector with high methanol

  4. Molecular Dynamics of Methylamine, Methanol, and Methyl Fluoride Cations in Intense 7 Micron Laser Fields

    E-Print Network [OSTI]

    Schlegel, H. Bernhard

    Molecular Dynamics of Methylamine, Methanol, and Methyl Fluoride Cations in Intense 7 Micron Laser of methylamine (CH3NH2 + ), methanol (CH3OH+ ), and methyl fluoride (CH3F+ ) cations by short, intense laser 7 m laser pulses. This work is motivated by recent studies of methanol cations by Yamanouchi and co

  5. The effect of methanol concentration on the performance of a passive DMFC

    E-Print Network [OSTI]

    Zhao, Tianshou

    The effect of methanol concentration on the performance of a passive DMFC J.G. Liu, T.S. Zhao *, R-breathing liquid feed direct methanol fuel cell (DMFC), with no external pumps or other auxiliary devices, was designed, fabricated and tested with different methanol concentrations. It was found that the cell

  6. Design of Extraction Column Methanol Recovery System for the TAME Reactive Distillation Process

    E-Print Network [OSTI]

    Al-Arfaj, Muhammad A.

    Design of Extraction Column Methanol Recovery System for the TAME Reactive Distillation Process, Dhahran, 31261, Saudi Arabia Abstract This paper studies the synthesis and the design of methanol recovery that methanol could be recovered completely from the hydrocarbon when 5 equilibrium trays in the extraction

  7. Global budget of methanol: Constraints from atmospheric observations Daniel J. Jacob,1

    E-Print Network [OSTI]

    Li, Qinbin

    Global budget of methanol: Constraints from atmospheric observations Daniel J. Jacob,1 Brendan D of atmospheric methanol to examine the consistency between observed atmospheric concentrations and current of methanol in the model is 7 days; gas-phase oxidation by OH accounts for 63% of the global sink, dry

  8. Development of high-power electrodes for a liquid-feed direct methanol fuel cell

    E-Print Network [OSTI]

    Development of high-power electrodes for a liquid-feed direct methanol fuel cell C. Lim, C.Y. Wang for a liquid-feed direct methanol fuel cell (DMFC) were fabricated by using a novel method of modi®ed Na.V. All rights reserved. Keywords: Direct methanol fuel cells; Membrane-electrode assembly (MEA); Polymer

  9. Methanol adsorbates on the DMFC cathode and their effect on the cell performance

    E-Print Network [OSTI]

    Zhao, Tianshou

    Methanol adsorbates on the DMFC cathode and their effect on the cell performance J. Prabhuram, T in the performance of a direct methanol fuel cell (DMFC) occurred after the cell had been operated at a higher temperature with higher methanol concentrations as compared with the polarization data collected under

  10. Structure of liquid and glassy methanol confined in cylindrical pores Denis Morineau1,2

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Structure of liquid and glassy methanol confined in cylindrical pores Denis Morineau1,2 , Régis scattering analysis of the density and the static structure factor of confined methanol at various and D=35 Ĺ. A change of the thermal expansivity of confined methanol at low temperature is the signature

  11. Partial oxidation of methanol over highly dispersed vanadia supported on silica SBA-15

    E-Print Network [OSTI]

    Bell, Alexis T.

    Partial oxidation of methanol over highly dispersed vanadia supported on silica SBA-15 C. Hessa 2005; accepted 6 August 2005 The partial oxidation of methanol to formaldehyde (FA) was studied over vanadia partly agglomerates into vanadia crystallites during methanol oxidation. KEY WORDS: supported

  12. Journal of Power Sources 167 (2007) 265271 Simultaneous oxygen-reduction and methanol-oxidation reactions

    E-Print Network [OSTI]

    Zhao, Tianshou

    2007-01-01

    Journal of Power Sources 167 (2007) 265­271 Simultaneous oxygen-reduction and methanol-reduction reaction (ORR) and methanol- oxidation reaction (MOR) at the cathode of a DMFC. Good agreements between a significant poisoning effect on the ORR by the presence of methanol at the cathode. The results also indicated

  13. Tropospheric methanol observations from space: retrieval1 evaluation and constraints on the seasonality of biogenic2

    E-Print Network [OSTI]

    Meskhidze, Nicholas

    1 Tropospheric methanol observations from space: retrieval1 evaluation and constraints Information1 2 3 #12; 3 1 FigureS1.Comparison of TES, IASI and airborne methanol measurements using GEOS-Chem as2 an intercomparison platform. Methanol abundance as modeled by GEOS-Chem (base-case3 simulation

  14. Correlating Catalytic Methanol Oxidation with the Structure and Oxidation State of Size-Selected Pt Nanoparticles

    E-Print Network [OSTI]

    Kik, Pieter

    Correlating Catalytic Methanol Oxidation with the Structure and Oxidation State of Size-Selected Pt nanoparticles (NPs) prepared by micelle encapsulation and supported on -Al2O3 during the oxidation of methanol the pretreatment. KEYWORDS: platinum, methanol oxidation, operando, XAFS, EXAFS, XANES, alumina, nanoparticle, size

  15. Exergetic analysis of fuel cell micropowerplants fed by methanol Nico Hotz a

    E-Print Network [OSTI]

    Daraio, Chiara

    Exergetic analysis of fuel cell micropowerplants fed by methanol Nico Hotz a , Ming-Tsang Lee polymer electrolyte fuel cell (PEFC) micropowerplant in combination with a steam reformer fed by methanol and a direct methanol fuel cell (DMFC) micropowerplant are analyzed numerically regarding their exergetic

  16. Data Compression with Prime Numbers

    E-Print Network [OSTI]

    Gordon Chalmers

    2005-11-16

    A compression algorithm is presented that uses the set of prime numbers. Sequences of numbers are correlated with the prime numbers, and labeled with the integers. The algorithm can be iterated on data sets, generating factors of doubles on the compression.

  17. Ethanol Vehicle and Infrastructure Codes and Standards Citations (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2010-07-01

    This document lists codes and standards typically used for U.S. ethanol vehicle and infrastructure projects.

  18. Clean Cities: Ethanol Basics, Fact Sheet, October 2008

    SciTech Connect (OSTI)

    Not Available

    2008-10-01

    Document answers frequently asked questions about ethanol as a transportation fuel, including those on production, environmental effects, and vehicles.

  19. Renewable Fuels Association’s National Ethanol Conference

    Broader source: Energy.gov [DOE]

    Mark Elless, a BETO technology manager, will be representing BETO at the 20th anniversary of the National Ethanol Conference.

  20. Understanding the Basics of Compressed Air Systems 

    E-Print Network [OSTI]

    Herron, D. J.

    1997-01-01

    Compressed air can be a manufacturing facilities' most expensive utility. Estimates and actual measurements of compressed air systems indicate ten to thirty-five percent of all compressed air generated is lost to leakage or improper use. Proper...

  1. EA-1694: Department of Energy Loan Guarantee to Highlands Ethanol, LLC, for the Cellulosic Ethanol Facility in Highlands County, Florida

    Broader source: Energy.gov [DOE]

    This EA will evaluate the environmental impacts of a proposal to issue a Federal loan guarantee to Highlands Ethanol, LLC, for a cellulosic ethanol facility in Highlands County, Florida. This EA is on hold.

  2. Ethanol Production and Gasoline Prices: A Spurious Correlation

    E-Print Network [OSTI]

    Rothman, Daniel

    Ethanol Production and Gasoline Prices: A Spurious Correlation Christopher R. Knittel and Aaron proponents of ethanol have argued that ethanol production greatly lowers gasoline prices, with one industry group claiming it reduced gasoline prices by 89 cents in 2010 and $1.09 in 2011. The estimates have been

  3. Ethanol Can Contribute to Energy and Environmental Goals

    E-Print Network [OSTI]

    Ethanol Can Contribute to Energy and Environmental Goals Alexander E. Farrell,1 * Richard J. Plevin the potential effects of increased biofuel use, we evaluated six representative analyses of fuel ethanol studies indicated that current corn ethanol technologies are much less petroleum-intensive than gasoline

  4. RESEARCH Open Access Simultaneous cell growth and ethanol production

    E-Print Network [OSTI]

    Chen, Wilfred

    RESEARCH Open Access Simultaneous cell growth and ethanol production from cellulose steps to their practical usage for ethanol production. Ideally, a recombinant microorganism, possessing the capability to utilize cellulose for simultaneous growth and ethanol production, is of great interest. We have

  5. What is (and is not) vital to advancing cellulosic ethanol

    E-Print Network [OSTI]

    California at Riverside, University of

    What is (and is not) vital to advancing cellulosic ethanol Charles E. Wyman Chemical of Engineering, University of California, Riverside, CA 92506, USA Ethanol made biologically from cellulosic ethanol; however, government policies are needed to overcome the per- ceived risk of first applications

  6. ORIGINAL INVESTIGATION Inhibition of phosphodiesterase-4 decreases ethanol intake

    E-Print Network [OSTI]

    ORIGINAL INVESTIGATION Inhibition of phosphodiesterase-4 decreases ethanol intake in mice Wei Hu Rationale Cyclic AMP (cAMP)­protein kinase A signal- ing has been implicated in the regulation of ethanol intracellular cAMP levels in the brain. However, the role of PDE4 in ethanol consumption remains unknown

  7. The Real Corn-Ethanol Transportation Tad W. Patzek

    E-Print Network [OSTI]

    Patzek, Tadeusz W.

    The Real Corn-Ethanol Transportation System Tad W. Patzek Department of Civil and Environmental of ethanol in the US is essentially equal to the unleaded gasoline prices in Europe research, mass transit systems, highway upgrades, etc. Corn and ethanol subsidies in the US channel money

  8. Biofuel derived from Microalgae Corn-based Ethanol

    E-Print Network [OSTI]

    Blouin-Demers, Gabriel

    · E10 vs. E85 choice · Examined of corn-based ethanol fuel systems on the following: - environmentalBiofuel derived from Microalgae Corn-based Ethanol #12;Outline · Production processes for each;Definitions Biofuel: clean fuel made from animal and plant fats and tissues (Hollebone, 2008) Ethanol

  9. An ecosystem-scale perspective of the net land methanol flux. Synthesis of micrometeorological flux measurements

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wohlfahrt, G.; Amelynck, C.; Ammann, C.; Arneth, A.; Bamberger, I.; Goldstein, A. H.; Gu, L.; Guenther, A.; Hansel, A.; Heinesch, B.; et al

    2015-07-09

    Methanol is the second most abundant volatile organic compound in the troposphere and plays a significant role in atmospheric chemistry. While there is consensus about the dominant role of living plants as the major source and the reaction with OH as the major sink of methanol, global methanol budgets diverge considerably in terms of source/sink estimates, reflecting uncertainties in the approaches used to model and the empirical data used to separately constrain these terms. Here we compiled micrometeorological methanol flux data from eight different study sites and reviewed the corresponding literature in order to provide a first cross-site synthesis ofmore »the terrestrial ecosystem-scale methanol exchange and present an independent data-driven view of the land–atmosphere methanol exchange. Our study shows that the controls of plant growth on production, and thus the methanol emission magnitude, as well as stomatal conductance on the hourly methanol emission variability, established at the leaf level, hold across sites at the ecosystem level. Unequivocal evidence for bi-directional methanol exchange at the ecosystem scale is presented. Deposition, which at some sites even exceeds methanol emissions, represents an emerging feature of ecosystem-scale measurements and is likely related to environmental factors favouring the formation of surface wetness. Methanol may adsorb to or dissolve in this surface water and eventually be chemically or biologically removed from it. Management activities in agriculture and forestry are shown to increase local methanol emission by orders of magnitude; however, they are neglected at present in global budgets. While contemporary net land methanol budgets are overall consistent with the grand mean of the micrometeorological methanol flux measurements, we caution that the present approach of simulating methanol emission and deposition separately is prone to opposing systematic errors and does not allow for full advantage to be taken of the rich information content of micrometeorological flux measurements.« less

  10. Compressed Air Storage Strategies; Industrial Technologies Program...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Industrial Technologies Program Suggested Actions * Review the plant's compressed air demand patterns to determine whether storage would be beneficial. * Examine the compressed...

  11. Ethanol production in Gram-positive microbes

    DOE Patents [OSTI]

    Ingram, L.O.; Barbosa-Alleyne, M.D.F.

    1996-01-09

    The subject invention concerns the transformation of Gram-positive bacteria with heterologous genes which confer upon these microbes the ability to produce ethanol as a fermentation product. Specifically exemplified is the transformation of bacteria with genes, obtainable from Zymomonas mobilis, which encode pyruvate decarboxylase and alcohol dehydrogenase. 2 figs.

  12. NOx Aftertreatment Using Ethanol as Reductant

    Broader source: Energy.gov [DOE]

    The hydrocarbon-SCR that was developed using ethanol and E85 as the reductant showed high NOx reduction, no need for thawing, use of existing infrastructure, and reduced system cost making it a viable alternative to urea-based SCR

  13. Ethanol production in Gram-positive microbes

    DOE Patents [OSTI]

    Ingram, L.O.; Barbosa-Alleyne, M.D.F.

    1999-06-29

    The subject invention concerns the transformation of Gram-positive bacteria with heterologous genes which confer upon these microbes the ability to produce ethanol as a fermentation product. Specifically exemplified is the transformation of bacteria with genes, obtainable from Zymomonas mobilis, which encode pyruvate decarboxylase and alcohol dehydrogenase. 2 figs.

  14. Ethanol production in Gram-positive microbes

    DOE Patents [OSTI]

    Ingram, Lonnie O'Neal (Gainesville, FL); Barbosa-Alleyne, Maria D. F. (Gainesville, FL)

    1996-01-01

    The subject invention concerns the transformation of Gram-positive bacteria with heterologous genes which confer upon these microbes the ability to produce ethanol as a fermentation product. Specifically exemplified is the transformation of bacteria with genes, obtainable from Zymomonas mobilis, which encode pyruvate decarboxylase and alcohol dehydrogenase.

  15. Ethanol production in gram-positive microbes

    DOE Patents [OSTI]

    Ingram, Lonnie O'Neal (Gainesville, FL); Barbosa-Alleyne, Maria D. F. (Gainesville, FL)

    1999-01-01

    The subject invention concerns the transformation of Gram-positive bacteria with heterologous genes which confer upon these microbes the ability to produce ethanol as a fermentation product. Specifically exemplified is the transformation of bacteria with genes, obtainable from Zymomonas mobilis, which encode pyruvate decarboxylase and alcohol dehydrogenase.

  16. Biotech Breakthrough Produces Ethanol from Waste Glycerin

    E-Print Network [OSTI]

    Stuart, Steven J.

    , it actually assists with waste processing, vitamin K production and food absorption. The same principleBiotech Breakthrough Produces Ethanol from Waste Glycerin Doing something about global warming that this process creates large quantities of waste glycerin, that was so far impossible to put to good use

  17. Modeling the natural attenuation of benzene in groundwater impacted by ethanol-blended fuels: Effect of ethanol content

    E-Print Network [OSTI]

    Alvarez, Pedro J.

    Modeling the natural attenuation of benzene in groundwater impacted by ethanol-blended fuels: Effect of ethanol content on the lifespan and maximum length of benzene plumes Diego E. Gomez1 and Pedro 10 March 2009. [1] A numerical model was used to evaluate how the concentration of ethanol

  18. Nucleic acid molecules conferring enhanced ethanol tolerance and microorganisms having enhanced tolerance to ethanol

    DOE Patents [OSTI]

    Brown, Steven; Guss, Adam; Yang, Shihui; Karpinets, Tatiana; Lynd, Lee; Shao, Xiongjun

    2014-01-14

    The present invention provides isolated nucleic acid molecules which encode a mutant acetaldehyde-CoA/alcohol dehydrogenase or mutant alcohol dehydrogenase and confer enhanced tolerance to ethanol. The invention also provides related expression vectors, genetically engineered microorganisms having enhanced tolerance to ethanol, as well as methods of making and using such genetically modified microorganisms for production of biofuels based on fermentation of biomass materials.

  19. Methanol production from eucalyptus wood chips. Attachment V. The Florida eucalyptus energy farm: environmental impacts

    SciTech Connect (OSTI)

    Fishkind, H.H.

    1982-06-01

    The overall environmental impact of the eucalyptus to methanol energy system in Florida is assessed. The environmental impacts associated with the following steps of the process are considered: (1) the greenhouse and laboratory; (2) the eucalyptus plantation; (3) transporting the mature logs; (4) the hammermill; and (5) the methanol synthesis plant. Next, the environmental effects of methanol as an undiluted motor fuel, methanol as a gasoline blend, and gasoline as motor fuels are compared. Finally, the environmental effects of the eucalypt gasification/methanol synthesis system are compared to the coal liquefaction and conversion system.

  20. Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) process. Technical progress report number 5, July 1--September 30, 1995

    SciTech Connect (OSTI)

    1995-12-31

    The project involves the construction of an 80,000 gallons per day (260 TPD) methanol unit utilizing coal-derived synthesis gas from Eastman`s integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} process is ideally suited for directly processing gases produced by modern-day coal gasifiers. Originally tested at a small, DOE-owned experimental unit in LaPorte, Texas, the technology provides several improvements essential for the economic coproduction of methanol and electricity directly from gasified coal. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface, protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates.

  1. Advances in compressible turbulent mixing

    SciTech Connect (OSTI)

    Dannevik, W.P.; Buckingham, A.C.; Leith, C.E.

    1992-01-01

    This volume includes some recent additions to original material prepared for the Princeton International Workshop on the Physics of Compressible Turbulent Mixing, held in 1988. Workshop participants were asked to emphasize the physics of the compressible mixing process rather than measurement techniques or computational methods. Actual experimental results and their meaning were given precedence over discussions of new diagnostic developments. Theoretical interpretations and understanding were stressed rather than the exposition of new analytical model developments or advances in numerical procedures. By design, compressibility influences on turbulent mixing were discussed--almost exclusively--from the perspective of supersonic flow field studies. The papers are arranged in three topical categories: Foundations, Vortical Domination, and Strongly Coupled Compressibility. The Foundations category is a collection of seminal studies that connect current study in compressible turbulent mixing with compressible, high-speed turbulent flow research that almost vanished about two decades ago. A number of contributions are included on flow instability initiation, evolution, and transition between the states of unstable flow onset through those descriptive of fully developed turbulence. The Vortical Domination category includes theoretical and experimental studies of coherent structures, vortex pairing, vortex-dynamics-influenced pressure focusing. In the Strongly Coupled Compressibility category the organizers included the high-speed turbulent flow investigations in which the interaction of shock waves could be considered an important source for production of new turbulence or for the enhancement of pre-existing turbulence. Individual papers are processed separately.

  2. NREL Proves Cellulosic Ethanol Can Be Cost Competitive (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2013-11-01

    Ethanol from non-food sources - known as "cellulosic ethanol" - is a near-perfect transportation fuel: it is clean, domestic, abundant, and renewable, and it can potentially replace 30% of the petroleum consumed in the United States, but its relatively high cost has limited its market. That changed in 2012, when the National Renewable Energy Laboratory (NREL) demonstrated the technical advances needed to produce cellulosic ethanol at a minimum ethanol selling price of $2.15/gallon (in 2007 dollars). Through a multi-year research project involving private industry, NREL has proven that cellulosic ethanol can be cost competitive with other transportation fuels.

  3. Recent Advances in Catalytic Conversion of Ethanol to Chemicals

    SciTech Connect (OSTI)

    Sun, Junming; Wang, Yong

    2014-04-30

    With increased availability and decreased cost, ethanol is potentially a promising platform molecule for the production of a variety of value-added chemicals. In this review, we provide a detailed summary of recent advances in catalytic conversion of ethanol to a wide range of chemicals and fuels. We particularly focus on catalyst advances and fundamental understanding of reaction mechanisms involved in ethanol steam reforming (ESR) to produce hydrogen, ethanol conversion to hydrocarbons ranging from light olefins to longer chain alkenes/alkanes and aromatics, and ethanol conversion to other oxygenates including 1-butanol, acetaldehyde, acetone, diethyl ether, and ethyl acetate.

  4. Emissions characterization of two methanol-fueled transit buses. Final report, April-September 1985

    SciTech Connect (OSTI)

    Ullman, T.L.; Hare, C.T.

    1986-02-01

    Exhaust emissions from the two methanol-powered buses used in the California Methanol Bus Demonstration have been characterized. The M.A.N. SU 240 bus is powered by M.A.N.'s D2566 FMUH methanol engine, and utilizes catalytic exhaust aftertreatment. The GMC RTS II 04 bus is powered by a first-generation DDAD 6V-92TA methanol engine without exhaust aftertreatment. Emissions of HC, CO, NO, unburned methanol, aldehydes, total particulates, and soluble fraction of particulate were determined for both buses over steady-state and transient chassis dynamometer test cycles. Emission levels from the M.A.N. bus were considerably lower than those from the GMC bus, with the exception of NO. Comparison of emission levels from methanol- and diesel-powered buses indicates that substantial reduction in emissions (especially particulate and NO) are possible with careful implementation of methanol fueling.

  5. Making Compressed Air System Decisions 

    E-Print Network [OSTI]

    Porri, R. E.

    1996-01-01

    stream_source_info ESL-IE-96-04-32.pdf.txt stream_content_type text/plain stream_size 5121 Content-Encoding ISO-8859-1 stream_name ESL-IE-96-04-32.pdf.txt Content-Type text/plain; charset=ISO-8859-1 MAKING COMPRESSED AIR... SYSTEM DECISIONS Richard E. Porri Product Manager ABSTRACT This paper presents a decision making process that will pennit the design, installation and operation ofa high efficiency and reliable compressed air system. The design of a compressed air...

  6. Solar photocatalytic conversion of CO{sub 2} to methanol

    SciTech Connect (OSTI)

    Ryba, G.; Shelnutt, J.; Prairie, M.R.; Assink, R.A.

    1997-02-01

    This report summarizes the three-year LDRD program directed at developing catalysts based on metalloporphyrins to reduce carbon dioxide. Ultimately it was envisioned that such catalysts could be made part of a solar-driven photoredox cycle by coupling metalloporphyrins with semiconductor systems. Such a system would provide the energy required for CO{sub 2} reduction to methanol, which is an uphill 6-electron reduction. Molecular modeling and design capabilities were used to engineer metalloporphyrin catalysts for converting CO{sub 2} to CO and higher carbon reduction products like formaldehyde, formate, and methanol. Gas-diffusion electrochemical cells were developed to carry out these reactions. A tin-porphyrin/alumina photocatalyst system was partially developed to couple solar energy to this reduction process.

  7. High specific power, direct methanol fuel cell stack

    DOE Patents [OSTI]

    Ramsey, John C. (Los Alamos, NM); Wilson, Mahlon S. (Los Alamos, NM)

    2007-05-08

    The present invention is a fuel cell stack including at least one direct methanol fuel cell. A cathode manifold is used to convey ambient air to each fuel cell, and an anode manifold is used to convey liquid methanol fuel to each fuel cell. Tie-bolt penetrations and tie-bolts are spaced evenly around the perimeter to hold the fuel cell stack together. Each fuel cell uses two graphite-based plates. One plate includes a cathode active area that is defined by serpentine channels connecting the inlet manifold with an integral flow restrictor to the outlet manifold. The other plate includes an anode active area defined by serpentine channels connecting the inlet and outlet of the anode manifold. Located between the two plates is the fuel cell active region.

  8. Effect of water concentration in the anode catalyst layer on the performance of direct methanol fuel cells operating

    E-Print Network [OSTI]

    Zhao, Tianshou

    Effect of water concentration in the anode catalyst layer on the performance of direct methanol fuel cells operating with neat methanol Q.X. Wu a , S.Y. Shen a , Y.L. He b , T.S. Zhao a cells Direct methanol fuel cells Neat methanol Water concentration a b s t r a c t This paper reports

  9. Guidance Document CompressedGases

    E-Print Network [OSTI]

    gases are toxic, flammable, pyrophoric, or corrosive. Liquefied compressed gases (cryogenic liquids of exposure may be delayed. Cold "Burns": Rapidly escaping gas from a cylinder can cause destruction freezing

  10. DATA COMPRESSION USING WAVELETS: ERROR ...

    E-Print Network [OSTI]

    1910-90-11

    algorithms that introduce differences between the original and compressed data in ... to choose an error metric that parallels the human visual system, so that image .... signal data along a communications channel, one sends integer codes that ...

  11. Compressed/Liquid Hydrogen Tanks

    Broader source: Energy.gov [DOE]

    Currently, DOE's physical hydrogen storage R&D focuses on the development of high-pressure (10,000 psi) composite tanks, cryo-compressed tanks, conformable tanks, and other advanced concepts...

  12. Compressed gas fuel storage system

    DOE Patents [OSTI]

    Wozniak, John J. (Columbia, MD); Tiller, Dale B. (Lincoln, NE); Wienhold, Paul D. (Baltimore, MD); Hildebrand, Richard J. (Edgemere, MD)

    2001-01-01

    A compressed gas vehicle fuel storage system comprised of a plurality of compressed gas pressure cells supported by shock-absorbing foam positioned within a shape-conforming container. The container is dimensioned relative to the compressed gas pressure cells whereby a radial air gap surrounds each compressed gas pressure cell. The radial air gap allows pressure-induced expansion of the pressure cells without resulting in the application of pressure to adjacent pressure cells or physical pressure to the container. The pressure cells are interconnected by a gas control assembly including a thermally activated pressure relief device, a manual safety shut-off valve, and means for connecting the fuel storage system to a vehicle power source and a refueling adapter. The gas control assembly is enclosed by a protective cover attached to the container. The system is attached to the vehicle with straps to enable the chassis to deform as intended in a high-speed collision.

  13. High compression rate text summarization

    E-Print Network [OSTI]

    Branavan, Satchuthananthavale Rasiah Kuhan

    2008-01-01

    This thesis focuses on methods for condensing large documents into highly concise summaries, achieving compression rates on par with human writers. While the need for such summaries in the current age of information overload ...

  14. Hydrogen isotope exchanges between water and methanol in interstellar ices

    E-Print Network [OSTI]

    Faure, A; Theulé, P; Quirico, E; Schmitt, B

    2015-01-01

    The deuterium fractionation of gas-phase molecules in hot cores is believed to reflect the composition of interstellar ices. The deuteration of methanol is a major puzzle, however, because the isotopologue ratio [CH2DOH]/[CH3OD], which is predicted to be equal to 3 by standard grain chemistry models, is much larger (~20) in low-mass hot corinos and significantly lower (~1) in high-mass hot cores. This dichotomy in methanol deuteration between low-mass and massive protostars is currently not understood. In this study, we report a simplified rate equation model of the deuterium chemistry occurring in the icy mantles of interstellar grains. We apply this model to the chemistry of hot corinos and hot cores, with IRAS 16293-2422 and the Orion~KL Compact Ridge as prototypes, respectively. The chemistry is based on a statistical initial deuteration at low temperature followed by a warm-up phase during which thermal hydrogen/deuterium (H/D) exchanges occur between water and methanol. The exchange kinetics is incorpor...

  15. Methanol Along the Path from Envelope to Protoplanetary Disc

    E-Print Network [OSTI]

    Drozdovskaya, Maria N; Visser, Ruud; Harsono, Daniel; van Dishoeck, Ewine F

    2014-01-01

    Interstellar methanol is considered to be a parent species of larger, more complex organic molecules. A physicochemical simulation of infalling parcels of matter is performed for a low-mass star-forming system to trace the chemical evolution from cloud to disc. An axisymmetric 2D semi-analytic model generates the time-dependent density and velocity distributions, and full continuum radiative transfer is performed to calculate the dust temperature and the UV radiation field at each position as a function of time. A comprehensive gas-grain chemical network is employed to compute the chemical abundances along infall trajectories. Two physical scenarios are studied, one in which the dominant disc growth mechanism is viscous spreading, and another in which continuous infall of matter prevails. The results show that the infall path influences the abundance of methanol entering each type of disc, ranging from complete loss of methanol to an enhancement by a factor of > 1 relative to the prestellar phase. Critical ch...

  16. New Catalysts for Direct Methanol Oxidation Fuel Cells

    SciTech Connect (OSTI)

    Adzic, Radoslav

    1998-08-01

    A new class of efficient electrocatalytic materials based on platinum - metal oxide systems has been synthetized and characterized by several techniques. Best activity was found with NiWO{sub 4}-, CoWO{sub 4}-, and RuO{sub 2}- srˇpported platinum catalysts. A very similar activity at room temperature was observed with the electrodes prepared with the catalyst obtained from International Fuel Cells Inc. for the same Pt loading. Surprisingly, the two tungstates per se show a small activity for methanol oxidation without any Pt loading. Synthesis of NiWO{sub 4} and CoWO{sub 4} were carried out by solid-state reactions. FTIR spectroscopy shows that the tungstates contain a certain amount of physically adsorbed water even after heating samples at 200{degrees}C. A direct relationship between the activity for methanol oxidation and the amount of adsorbed water on those oxides has been found. The Ru(0001) single crystal shows a very small activity for CO adsorption and oxidation, in contrast to the behavior of polycrystalline Ru. In situ extended x-ray absorption fine structure spectroscopy (EXAFS) and x-ray absorption near edge spectroscopy (XANES) showed that the OH adsorption on Ru in the Pt-Ru alloy appears to be the limiting step in methanol oxidation. This does not occur for Pt-RuO{SUB 2} electrocatalyst, which explains its advantages over the Pt-Ru alloys. The IFCC electrocatalyst has the properties of the Pt-Ru alloy.

  17. An enzyme-amplified microtiter plate assay for ethanol: Its application to the detection of peanut ethanol and alcohol dehydrogenase

    SciTech Connect (OSTI)

    Chung, S.Y.; Vercellotti, J.R. [USDA-ARS-SRRC, New Orleans, LA (United States); Sanders, T.H. [USDA-ARS-NCSU, Raleigh, NC (United States)

    1995-12-01

    A calorimetric microliter plate assay for ethanol amplified by aldehyde dehydrogenase (ALDH) was developed. In the assay ethanol from a sample took part in a chain-reaction catalyzed by alcohol dehydrogenase (ADH) and amplified by ALDH in the presence of NAD{sup +}, diaphorase, and p-ibdonitrotetrazolium-violet (INT-violet)(a precursor of red product). The resultant reaction gave a red color, the intensity of which was proportional to the amount of ethanol present. Using the technique, the content of activity from peanuts of differing maturity and curing stages were determined respectively. Data showed that immature peanuts had a higher level of ethanol and a lower ADH activity than mature peanuts, and that the level of ethanol and ADH activity decreased with the curing time. This indicates that peanut maturity and curing have an effect on ethanol. Also, this implies that other peanut volatiles could be affected in the same way as ethanol, a major volatile in peanuts.

  18. Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) process. Technical progress report number 6, October 1--December 31, 1995

    SciTech Connect (OSTI)

    1996-12-31

    The project involves the construction of an 80,000 gallons per day (260 TPD) methanol unit utilizing coal-derived synthesis gas from Eastman`s integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} process is ideally suited for directly processing gases produced by modern-day coal gasifiers. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates. At the Eastman complex, the technology will be integrated with existing coal-gasifiers. A carefully developed test plan will allow operations at Eastman to simulate electricity demand load-following in coal-based IGCC facilities. The operations will also demonstrate the enhanced stability and heat dissipation of the conversion process, its reliable on/off operation, and its ability to produce methanol as a clean liquid fuel without additional upgrading. An off-site product testing program will be conducted to demonstrate the suitability of the methanol product as a transportation fuel and as a fuel for stationary applications for small modular electric power generators for distributed power.

  19. Robust Header Compression for Multimedia Services

    E-Print Network [OSTI]

    Reisslein, Martin

    JSQ Testbed #12;Motivation and Introduction · Wireless link is highly error-prone · Large round trip on lossy links with long round trip times #12;Metric for compression performance · Compression efficiency ­ Compressed header size versus original header size · Compression transparency ­ Decompressed headers has

  20. Unbiased water and methanol maser surveys of NGC 1333

    SciTech Connect (OSTI)

    Lyo, A-Ran; Kim, Jongsoo; Byun, Do-Young; Lee, Ho-Gyu, E-mail: arl@kasi.re.kr [Korea Astronomy and Space Science Institute, 776, Daedeokdae-ro Yuseong-gu, Daejeon 305-348 (Korea, Republic of)

    2014-11-01

    We present the results of unbiased 22 GHz H{sub 2}O water and 44 GHz class I CH{sub 3}OH methanol maser surveys in the central 7' × 10' area of NGC 1333 and two additional mapping observations of a 22 GHz water maser in a ?3' × 3' area of the IRAS4A region. In the 22 GHz water maser survey of NGC 1333 with a sensitivity of ? ? 0.3 Jy, we confirmed the detection of masers toward H{sub 2}O(B) in the region of HH 7-11 and IRAS4B. We also detected new water masers located ?20'' away in the western direction of IRAS4B or ?25'' away in the southern direction of IRAS4A. We could not, however, find young stellar objects or molecular outflows associated with them. They showed two different velocity components of ?0 and ?16 km s{sup –1}, which are blue- and redshifted relative to the adopted systemic velocity of ?7 km s{sup –1} for NGC 1333. They also showed time variabilities in both intensity and velocity from multi-epoch observations and an anti-correlation between the intensities of the blue- and redshifted velocity components. We suggest that the unidentified power source of these masers might be found in the earliest evolutionary stage of star formation, before the onset of molecular outflows. Finding this kind of water maser is only possible through an unbiased blind survey. In the 44 GHz methanol maser survey with a sensitivity of ? ? 0.5 Jy, we confirmed masers toward IRAS4A2 and the eastern shock region of IRAS2A. Both sources are also detected in 95 and 132 GHz methanol maser lines. In addition, we had new detections of methanol masers at 95 and 132 GHz toward IRAS4B. In terms of the isotropic luminosity, we detected methanol maser sources brighter than ?5 × 10{sup 25} erg s{sup –1} from our unbiased survey.

  1. Ethanol extraction of phytosterols from corn fiber

    DOE Patents [OSTI]

    Abbas, Charles (Champaign, IL); Beery, Kyle E. (Decatur, IL); Binder, Thomas P. (Decatur, IL); Rammelsberg, Anne M. (Decatur, IL)

    2010-11-16

    The present invention provides a process for extracting sterols from a high solids, thermochemically hydrolyzed corn fiber using ethanol as the extractant. The process includes obtaining a corn fiber slurry having a moisture content from about 20 weight percent to about 50 weight percent solids (high solids content), thermochemically processing the corn fiber slurry having high solids content of 20 to 50% to produce a hydrolyzed corn fiber slurry, dewatering the hydrolyzed corn fiber slurry to achieve a residual corn fiber having a moisture content from about 30 to 80 weight percent solids, washing the residual corn fiber, dewatering the washed, hydrolyzed corn fiber slurry to achieve a residual corn fiber having a moisture content from about 30 to 80 weight percent solids, and extracting the residual corn fiber with ethanol and separating at least one sterol.

  2. Intermediate Ethanol Blends Catalyst Durability Program

    SciTech Connect (OSTI)

    West, Brian H; Sluder, Scott; Knoll, Keith; Orban, John; Feng, Jingyu

    2012-02-01

    In the summer of 2007, the U.S. Department of Energy (DOE) initiated a test program to evaluate the potential impacts of intermediate ethanol blends (also known as mid-level blends) on legacy vehicles and other engines. The purpose of the test program was to develop information important to assessing the viability of using intermediate blends as a contributor to meeting national goals for the use of renewable fuels. Through a wide range of experimental activities, DOE is evaluating the effects of E15 and E20 - gasoline blended with 15% and 20% ethanol - on tailpipe and evaporative emissions, catalyst and engine durability, vehicle driveability, engine operability, and vehicle and engine materials. This report provides the results of the catalyst durability study, a substantial part of the overall test program. Results from additional projects will be reported separately. The principal purpose of the catalyst durability study was to investigate the effects of adding up to 20% ethanol to gasoline on the durability of catalysts and other aspects of the emissions control systems of vehicles. Section 1 provides further information about the purpose and context of the study. Section 2 describes the experimental approach for the test program, including vehicle selection, aging and emissions test cycle, fuel selection, and data handling and analysis. Section 3 summarizes the effects of the ethanol blends on emissions and fuel economy of the test vehicles. Section 4 summarizes notable unscheduled maintenance and testing issues experienced during the program. The appendixes provide additional detail about the statistical models used in the analysis, detailed statistical analyses, and detailed vehicle specifications.

  3. Alternative Fuels Data Center: Ethanol Fuel Basics

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels Data Center Home Page on Digg FindPortsas aEthanol Benefits and

  4. Simultaneous cell growth and ethanol production from cellulose by an engineered yeast consortium displaying a functional mini-cellulosome

    E-Print Network [OSTI]

    Goyal, Garima; Tsai, Shen-Long; Madan, Bhawna; DaSilva, Nancy A; Chen, Wilfred

    2011-01-01

    Cellulase, clostridia, and ethanol. Microbiol Mol Biol RevNext- generation cellulosic ethanol technologies and theirProduction of cellulosic ethanol in Saccharomyces cerevisiae

  5. Energy, Carbon Dioxide and Water Use Implications of Hydrous Ethanol Production

    E-Print Network [OSTI]

    Saffy, Howard A.; Northrop, William; Kittelson, David; Boies, Adam M.

    2015-08-24

    than anhydrous ethanol. In this study, we investigate corn ethanol production from a dry-mill, natural gas-fired corn ethanol refinery, producing ethanol with a range of ethanol concentrations from 58°wt% - 100°wt% to determine the effect on energy use...

  6. Interaction of alkanes with an amorphous methanol film at 15-180 K

    SciTech Connect (OSTI)

    Souda, Ryutaro

    2005-09-15

    The hydrogen-bond imperfections and glass-liquid transition of the amorphous methanol film have been investigated on the basis of the film dewetting and the incorporation/desorption of alkane molecules adsorbed on the surface. The butane is incorporated completely in the bulk of the porous methanol film up to 70 K. At least two distinct states exist for the incorporated butane; one is assignable to solvated molecules in the bulk and the other is weakly bound species at the surface or in the subsurface site. For the nonporous methanol film, the uptake of butane in the bulk is quenched but butane forms a surface complex with methanol above 80 K. The butane incorporated in the bulk of the glassy methanol film is released at 120 K, where dewetting of the methanol film occurs simultaneously due to evolution of the supercooled liquid phase.

  7. Transition from cool flame to thermal flame in compression ignition process

    SciTech Connect (OSTI)

    Yamada, Hiroyuki; Suzaki, Kotaro; Goto, Yuichi; Tezaki, Atsumu

    2008-07-15

    The mechanism that initiates thermal flames in compression ignition has been studied. Experimentally, a homogeneous charge compression ignition (HCCI) engine was used with DME, n-heptane, and n-decane. Arrhenius plots of the heat release rate in the HCCI experiments showed that rates of heat release with DME, n-heptane, and n-decane exhibited a certain activation energy that is identical to that of the H{sub 2}O{sub 2} decomposition reaction. The same feature was observed in diesel engine operation using ordinary diesel fuel with advanced ignition timing to make ignition occur after the end of fuel injection. These experimental results were reproduced in nondimensional simulations using kinetic mechanisms for DME, n-heptane, and n-decane, the last being developed by extending the n-heptane mechanism. Methanol addition, which suppresses low-temperature oxidation (LTO) and delays the ignition timing, had no effect on the activation energy obtained from the Arrhenius plot of heat release rate. Nevertheless, methanol addition lowered the heat release rates during the prethermal flame process. This is because H{sub 2}O{sub 2} formation during cool flame was reduced by adding methanol. The mechanism during the transition process from cool flame to thermal flame can be explained quantitatively using thermal explosion theory, in which the rate-determining reaction is H{sub 2}O{sub 2} decomposition, assuming that heat release in this period is caused by partial oxidation of DME and HCHO initiated with the reaction with OH produced though H{sub 2}O{sub 2} decomposition. (author)

  8. Mass spectral characterization of oxygen-containing aromatics with methanol chemical ionization

    SciTech Connect (OSTI)

    Buchanan, M.V.

    1984-03-01

    Chemical ionization mass spectrometry with methanol and deuterated methanol as ionization reagents is used to differentiate oxygen-containing aromatics, including phenols, aromatic ethers, and aromatic substituted alcohols, as well as compounds containing more than one oxygen atom. The analogous sulfur-containing aromatics may be similarly differentiated. Methanol chemical ionization is used to characterize a neutral aromatic polar subfraction of a coal-derived liquid by combined gas chromatography/mass spectrometry. 16 references, 2 tables, 1 figure.

  9. Lipid-enhanced ethanol production from xylose by Pachysolen tannophilus

    SciTech Connect (OSTI)

    Dekker, R.F.H.

    1986-04-01

    A number of different yeasts are now recognized as being capable of fermenting the pentose sugar, D-xylose, into ethanol. The most prominent among these are Pachysolen tannophilus and several Candida species. D-Xylose is found principally in lignocellulosic materials where it occurs as the main constitutent of the hemicellulosic xylans (1,4-..beta..-D-heteroxylans). With the exception of Candida XF-217, the conversion yields of xylose into ethanol for most yeasts were generally low (less than 70% of theoretical when grown on at least 50 g/l xylose). The low ethanol yields are attributable to a number of factors: 1) fermentation was not performed under conditions that maximize ethanol formation; 2) ethanol was not the major fermentation end-product, (e.g., acetic acid xylitol, and arabinitol are also known products, 3) ethanol toxicity; 4) ethanol is assimilated when the substrate becomes limiting; 4.8 and 5) osmotic sensitivity to high substrate levels, i.e. substrate inhibition. Attempts to increase ethanol yields of yeasts by adding exogenous lipids (e.g., oleic and linoleic acids, or ergosterol or its ester, lipid mixtures, or protein-lipid mixtures) to nutrient medium have succeeded in improving ethanol yields and also in reducing fermentation times. These lipids, when added to the nutrient medium, were incorporated into the yeast's cellular membrane. The protective action of these lipids was to alleviate the inhibitory effect of ethanol which then allowed the cells to tolerate higher ethanol levels. This communication reports on improved ethanol yields arising from the fermentation of xylose by a Pachysolen tannophilus strain when grown semi-aerobically in the presence of exogenous-added lipids. 17 references.

  10. Lipid-enhanced ethanol production from xylose by Pachysolen tannophilus

    SciTech Connect (OSTI)

    Dekker, R.F.H.

    1986-01-01

    This paper reports improved ethanol yields following the fermentation of xylose by a Pachysolen tannophilus strain when grown semi-aerobically in the presence of exogenous-added lipids. Profiles for ethanol production from 45 g/L xylose when grown on a medium containing ergosterol, linoleic acid, Tween-80, a mixture of the three lipids and no lipids (control) are presented. The enhancement in the amount of ethanol produced was most pronounced after 72 h fermentation.

  11. Energy Landscape of Water and Ethanol on Silica Surfaces

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wu, Di; Guo, Xiaofeng; Sun, Hui; Navrotsky, Alexandra

    2015-06-26

    Fundamental understanding of small molecule–silica surface interactions at their interfaces is essential for the scientific, technological, and medical communities. We report direct enthalpy of adsorption (?hads) measurements for ethanol and water vapor on porous silica glass (CPG-10), in both hydroxylated and dehydroxylated (hydrophobic) forms. Results suggest a spectrum of energetics as a function of coverage, stepwise for ethanol but continuous for water. The zero-coverage enthalpy of adsorption for hydroxylated silica shows the most exothermic enthalpies for both water (-72.7 ± 3.1 kJ/mol water) and ethanol (-78.0 ± 1.9 kJ/mol ethanol). The water adsorption enthalpy becomes less exothermic gradually until reachingmore »its only plateau (-20.7 ± 2.2 kJ/mol water) reflecting water clustering on a largely hydrophobic surface, while the enthalpy of ethanol adsorption profile presents two well separated plateaus, corresponding to strong chemisorption of ethanol on adsorbate-free silica surface (-66.4 ± 4.8 kJ/mol ethanol), and weak physisorption of ethanol on ethanol covered silica (-4.0 ± 1.6 kJ/mol ethanol). On the other hand, dehydroxylation leads to missing water–silica interactions, whereas the number of ethanol binding sites is not impacted. The isotherms and partial molar properties of adsorption suggest that water may only bind strongly onto the silanols (which are a minor species on silica glass), whereas ethanol can interact strongly with both silanols and the hydrophobic areas of the silica surface.« less

  12. Energy Landscape of Water and Ethanol on Silica Surfaces

    SciTech Connect (OSTI)

    Wu, Di; Guo, Xiaofeng; Sun, Hui; Navrotsky, Alexandra

    2015-06-26

    Fundamental understanding of small molecule–silica surface interactions at their interfaces is essential for the scientific, technological, and medical communities. We report direct enthalpy of adsorption (?hads) measurements for ethanol and water vapor on porous silica glass (CPG-10), in both hydroxylated and dehydroxylated (hydrophobic) forms. Results suggest a spectrum of energetics as a function of coverage, stepwise for ethanol but continuous for water. The zero-coverage enthalpy of adsorption for hydroxylated silica shows the most exothermic enthalpies for both water (-72.7 ± 3.1 kJ/mol water) and ethanol (-78.0 ± 1.9 kJ/mol ethanol). The water adsorption enthalpy becomes less exothermic gradually until reaching its only plateau (-20.7 ± 2.2 kJ/mol water) reflecting water clustering on a largely hydrophobic surface, while the enthalpy of ethanol adsorption profile presents two well separated plateaus, corresponding to strong chemisorption of ethanol on adsorbate-free silica surface (-66.4 ± 4.8 kJ/mol ethanol), and weak physisorption of ethanol on ethanol covered silica (-4.0 ± 1.6 kJ/mol ethanol). On the other hand, dehydroxylation leads to missing water–silica interactions, whereas the number of ethanol binding sites is not impacted. The isotherms and partial molar properties of adsorption suggest that water may only bind strongly onto the silanols (which are a minor species on silica glass), whereas ethanol can interact strongly with both silanols and the hydrophobic areas of the silica surface.

  13. Compressive behavior of fine sand.

    SciTech Connect (OSTI)

    Martin, Bradley E.; Kabir, Md. E.; Song, Bo; Chen, Wayne

    2010-04-01

    The compressive mechanical response of fine sand is experimentally investigated. The strain rate, initial density, stress state, and moisture level are systematically varied. A Kolsky bar was modified to obtain uniaxial and triaxial compressive response at high strain rates. A controlled loading pulse allows the specimen to acquire stress equilibrium and constant strain-rates. The results show that the compressive response of the fine sand is not sensitive to strain rate under the loading conditions in this study, but significantly dependent on the moisture content, initial density and lateral confinement. Partially saturated sand is more compliant than dry sand. Similar trends were reported in the quasi-static regime for experiments conducted at comparable specimen conditions. The sand becomes stiffer as initial density and/or confinement pressure increases. The sand particle size become smaller after hydrostatic pressure and further smaller after dynamic axial loading.

  14. Wet Gasification of Ethanol Residue: A Preliminary Assessment

    SciTech Connect (OSTI)

    Brown, Michael D.; Elliott, Douglas C.

    2008-09-22

    A preliminary technoeconomic assessment has been made of several options for the application of catalytic hydrothermal gasification (wet gasification) to ethanol processing residues.

  15. DOE Selects Five Ethanol Conversion Projects for $23 Million...

    Broader source: Energy.gov (indexed) [DOE]

    of 35 billion gallons of ethanol a year by 2017. Funding for these projects, an integral part of the President's Biofuels Initiative, will enable biorefineries to produce...

  16. Advancing Cellulosic Ethanol for Large Scale Sustainable Transportation

    E-Print Network [OSTI]

    Wyman, C

    2007-01-01

    What is Holding Back Cellulosic Ethanol? • Capital costs arehigh • The cost of capital is high – particularly for newCost Elements Biomass Feedstock Feed Handling Capital

  17. Secretary Bodman Touts Importance of Cellulosic Ethanol at Georgia...

    Energy Savers [EERE]

    "The production of cost-competitive cellulosic ethanol is a significant part of America's energy future. This new facility, one of six commercial scale biorefineries to be...

  18. Effects of ethanol and reactive species on Hepatitis C virus

    E-Print Network [OSTI]

    Seronello, Scott E.

    2010-01-01

    the mutation rate of hepatitis C virus RNA. Manuscript inreactive oxygen species during hepatitis C virus infection.2010) Ethanol enhances hepatitis C virus replication through

  19. Emissions from ethanol- and LPG-fueled vehicles

    SciTech Connect (OSTI)

    Pitstick, M.E.

    1995-06-01

    This paper addresses the environmental concerns of using neat ethanol and liquefied petroleum gas (LPG) as transportation fuels in the United States. Low-level blends of ethanol (10%) with gasoline have been used as fuels in the United States for more than a decade, but neat ethanol (85% or more) has only been used extensively in Brazil. LPG, which consists mostly of propane, is already used extensively as a vehicle fuel in the United States, but its use has been limited primarily to converted fleet vehicles. Increasing U.S. interest in alternative fuels has raised the possibility of introducing neat-ethanol vehicles into the market and expanding the number of LPG vehicles. Use of such vehicles, and increased production and consumption of fuel ethanol and LPG, will undoubtedly have environmental impacts. If the impacts are determined to be severe, they could act as barriers to the introduction of neat-ethanol and LPG vehicles. Environmental concerns include exhaust and evaporative emissions and their impact on ozone formation and global warming, toxic emissions from fuel combustion and evaporation, and agricultural impacts from production of ethanol. The paper is not intended to be judgmental regarding the overall attractiveness of ethanol or LPG as compared with other transportation fuels. The environmental concerns are reviewed and summarized, but only conclusion reached is that there is no single concern that is likely to prevent the introduction of neat-ethanol-fueled vehicles or the increase in LPG-fueled vehicles.

  20. Evolved strains of Scheffersomyces stipitis achieving high ethanol...

    Office of Scientific and Technical Information (OSTI)

    Lignocellulosic biomass is an abundant, renewable feedstock useful for the production of fuel-grade ethanol via the processing steps of pretreatment, enzyme hydrolysis, and...

  1. Biofuel alternatives to ethanol: pumping the microbial well

    E-Print Network [OSTI]

    Fortman, J.L.

    2011-01-01

    ethanol and plant-based biodiesel ( Box 1). Although bio-acid pathway Currently, biodiesel production uses plant oilsbeen developed for use as biodiesel. However, if biodiesel

  2. Biofuel alternatives to ethanol: pumping the microbial well

    E-Print Network [OSTI]

    Fortman, J. L.

    2010-01-01

    costs and benefits of biodiesel and ethanol biofuels. Proc.187 24 Fukuda, H. et al. (2001) Biodiesel fuel production by26 Chisti, Y. (2007) Biodiesel from microalgae. Biotechnol.

  3. An Environmental and Policy Evaluation of Cellulosic Ethanol 

    E-Print Network [OSTI]

    Hurtado, Lisa Diane

    2012-07-16

    of energy crops. A new policy is proposed to support the sustainable, environmentally responsible development of cellulosic ethanol in the US....

  4. Biochemical Production of Ethanol from Corn Stover: 2007 State...

    Broader source: Energy.gov (indexed) [DOE]

    Process Design and Economics for Biochemical Conversion of Lignocellulosic Biomass to Ethanol: Dilute-Acid Pretreatment and Enzymatic Hydrolysis of Corn Stover Process Design and...

  5. Ethanol Effects on Lean-Burn and Stoichiometric GDI Emissions

    Broader source: Energy.gov [DOE]

    Characterized particulate emissions from U.S.-legal stoichiometric GDI and European certified lean-burn GDI vehicles operating on ethanol blends

  6. Lignocellulosic Biomass to Ethanol Process Design and Economics...

    Broader source: Energy.gov (indexed) [DOE]

    Process Design and Economics for Biochemical Conversion of Lignocellulosic Biomass to Ethanol: Dilute-Acid Pretreatment and Enzymatic Hydrolysis of Corn Stover Process...

  7. Appendix D: 2012 Cellulosic Ethanol Success, Bioenergy Technologies...

    Broader source: Energy.gov (indexed) [DOE]

    produce cellulosic ethanol at commercial-scale costs that are competitive with gasoline production at 110barrel of crude oil. Many industry partners are also demonstrating...

  8. Selective zeolite catalyst for preparing ethylbenzene from toluene and methanol

    SciTech Connect (OSTI)

    Vasil`ev, A.N.; Galinskii, A.A.

    1995-10-10

    A selective catalyst for methylation of toluene in the side chain has been prepared by modification of Cs{sub 0.85}NaX zeolite. Highly active catalysts for alkylation of toluene with methanol in the side chain are prepared by hydrothermal modification of zeolites. Previously it was found that with a high cesium content in catalysts, which was reached by ion exchange, their selectivity with respect to styrene considerably increases. In this paper the authors proposed a procedure for preparing a highly selective catalyst for synthesis of ethylbenzene.

  9. STATISTICAL PROPERTIES OF 12.2 GHz METHANOL MASERS ASSOCIATED WITH A COMPLETE SAMPLE OF 6.7 GHz METHANOL MASERS

    SciTech Connect (OSTI)

    Breen, S. L.; Caswell, J. L.; Green, J. A.; Voronkov, M. A. [CSIRO Astronomy and Space Science, P.O. Box 76, Epping, NSW 1710 (Australia); Ellingsen, S. P. [School of Mathematics and Physics, University of Tasmania, Private Bag 37, Hobart, Tasmania 7001 (Australia); Fuller, G. A.; Quinn, L. J.; Avison, A., E-mail: Shari.Breen@csiro.au [Jodrell Bank Centre for Astrophysics, Alan Turing Building, School of Physics and Astronomy, University of Manchester, Manchester M13 9PL (United Kingdom)

    2011-06-01

    We present definitive detection statistics for 12.2 GHz methanol masers toward a complete sample of 6.7 GHz methanol masers detected in the Methanol Multibeam survey south of declination -20{sup 0}. In total, we detect 250 12.2 GHz methanol masers toward 580 6.7 GHz methanol masers. This equates to a detection rate of 43.1%, which is lower than that of previous significant searches of comparable sensitivity. Both the velocity ranges and the flux densities of the target 6.7 GHz sources surpass that of their 12.2 GHz companion in almost all cases. Eighty percent of the detected 12.2 GHz methanol maser peaks are coincident in velocity with the 6.7 GHz maser peak. Our data support an evolutionary scenario whereby the 12.2 GHz sources are associated with a somewhat later evolutionary stage than the 6.7 GHz sources devoid of this transition. Furthermore, we find that the 6.7 GHz and 12.2 GHz methanol sources increase in luminosity as they evolve. In addition to this, evidence for an increase in velocity range with evolution is presented. This implies that it is not only the luminosity but also the volume of gas conducive to the different maser transitions that increases as the sources evolve. Comparison with GLIMPSE mid-infrared sources has revealed a coincidence rate between the locations of the 6.7 GHz methanol masers and GLIMPSE point sources similar to that achieved in previous studies. Overall, the properties of the GLIMPSE sources with and without 12.2 GHz counterparts are similar. There is a higher 12.2 GHz detection rate toward those 6.7 GHz methanol masers that are coincident with extended green objects.

  10. Mechanical compression attenuates normal human bronchial epithelial wound healing

    E-Print Network [OSTI]

    Arold, Stephen P.; Malavia, Nikita; George, Steven C.

    2009-01-01

    Open Access Research Mechanical compression attenuatesto the application of mechanical compression in the presenceResults: We found that mechanical compression and scrape

  11. Fact Sheet: Isothermal Compressed Air Energy Storage (August...

    Office of Environmental Management (EM)

    Isothermal Compressed Air Energy Storage (August 2013) Fact Sheet: Isothermal Compressed Air Energy Storage (August 2013) SustainX will demonstrate an isothermal compressed air...

  12. Pulse compression and modelocking by using TPA in silicon waveguides

    E-Print Network [OSTI]

    Tien, En-Kuang; Yuksek, Nuh S; Qian, Feng; Boyraz, Ozdal

    2007-01-01

    F. Qian, O. Boyraz, “Pulse Compression and Modelocking byPulse compression and modelocking by using TPA in silicona novel broadband pulse compression and modelocking scheme

  13. Cryo-Compressed Hydrogen Storage: Performance and Cost Review...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Compressed Hydrogen Storage: Performance and Cost Review Cryo-Compressed Hydrogen Storage: Performance and Cost Review Presented at the R&D Strategies for Compressed,...

  14. Hydrogen assisted combustion of ethanol in Diesel enginesHydrogen assisted combustion of ethanol in Diesel engines Anil Singh Bika, Luke Franklin, Prof. David B. Kittelson

    E-Print Network [OSTI]

    Minnesota, University of

    Hydrogen assisted combustion of ethanol in Diesel enginesHydrogen assisted combustion of ethanol a means of using nearly pure ethanol as a diesel engine fuel by using hydrogen rich gases to facilitate of combustion (SOC) · A good diesel fuel has a low ignition delay period and hence a high CN · Ethanol has

  15. Divergence in Cactophilic Drosophila: The Evolutionary Significance of Adult Ethanol Metabolism

    E-Print Network [OSTI]

    Etges, William J.

    Divergence in Cactophilic Drosophila: The Evolutionary Significance of Adult Ethanol Metabolism IN CACTOPHILIC DROSOPHILA: THE EVOLUTIONARY SIGNIFICANCE OF ADULT ETHANOL METABOLISM WILLIAMJ. ETGES~ Department of volatile com- pounds, particularly ethanol, than Opuntia or other Sonoran Desert columnar cacti, because

  16. RAW MATERIALS EVALUATION AND PROCESS DEVELOPMENT STUDIES FOR CONVERSION OF BIOMASS TO SUGARS AND ETHANOL

    E-Print Network [OSTI]

    Wilke, C.R.

    2011-01-01

    OF BIOMASS TO SUGARS AND ETHANOL C. R. Wilke, R. D. Yang,of Cellulose Conversion on Ethanol Cost. References Wilke,of Hydrolyzate to Ethanol and Single Cell Protein,"

  17. PROCESS DEVELOPMENT STUDIES ON THE BIOCONVERSION OF CELLULOSE AND PRODUCTION OF ETHANOL

    E-Print Network [OSTI]

    Wilke, C.R.

    2011-01-01

    OF CELLULOSE AND PRODUCTION OF ETHANOL under auspices of22 Mohammad Riaz ETHANOL FERMENTATION STUDIES II I. A. B.Hydrolyzates to Ethanol J2 Ren-Der Yang

  18. Comparative analysis of hospital and forensic laboratory ethanol concentrations: A 15 month investigation of antemortem specimens

    E-Print Network [OSTI]

    Saitman, A; Estrada, J; Fitzgerald, RL; McIntyre, IM

    2015-01-01

    evident at lower blood ethanol concentrations and provideAW. Interpreting results of ethanol analysis in postmortemA. Fast quanti?cation of ethanol in whole blood specimens by

  19. Low and intermediate temperature oxidation of ethanol and ethanol-PRF blends: An experimental and modeling study

    SciTech Connect (OSTI)

    Haas, Francis M.; Chaos, Marcos; Dryer, Frederick L.

    2009-12-15

    In this brief communication, we present new experimental species profile measurements for the low and intermediate temperature oxidation of ethanol under knock-prone conditions. These experiments show that ethanol exhibits no global low temperature reactivity at these conditions, although we note the heterogeneous decomposition of ethanol to ethylene and water. Similar behavior is reported for an E85 blend in n-heptane. Kinetic modeling results are presented to complement these experiments and elucidate the interaction of ethanol and primary reference fuels undergoing cooxidation. (author)

  20. NMR and NQR parameters of ethanol crystal

    E-Print Network [OSTI]

    Milinkovic, M

    2012-01-01

    Electric field gradients and chemical shielding tensors of the stable monoclinic crystal phase of ethanol are computed. The projector-augmented wave (PAW) and gauge-including projector-augmented wave (GIPAW) models in the periodic plane-wave density functional theory are used. The crystal data from X-ray measurements, as well as the structures where either all atomic, or only hydrogen atom positions are optimized in the density functional theory are analyzed. These structural models are also studied by including the semi-empirical Van der Waals correction to the density functional theory. Infrared spectra of these five crystal models are calculated.

  1. Great Valley Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History View New PagesSustainableGlynn County, Georgia:Oregon: EnergyGreat Basin GeothermalValley Ethanol

  2. Didion Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTIONRobertsdale, Alabama (UtilityInstrumentsArea (DOE GTP) Jump to:SouthBar,eĂłlicoDidion Ethanol LLC

  3. Michigan Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo, Maryland: Energy ResourcesDec 2005 WindPRO is developedShores,Ethanol LLC Jump to:

  4. Millennium Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo, Maryland: Energy ResourcesDec 2005 WindPROLLC JumpEthanol LLC Jump to: navigation, search

  5. Kaapa Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History View NewTexas: Energy ResourcesOrder atHills,New York:Just Hot ResourcesEnergyKaapa Ethanol LLC

  6. North Country Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo, Maryland:NPI VenturesNew Hampshire: EnergyReservoirBrookfield,CapeCastle,Country Ethanol

  7. Northern Lights Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QAsource History ViewMayo, Maryland:NPI VenturesNew Hampshire:sourceNortheast Aitkin,SHRM WindLights Ethanol LLC

  8. East Coast Ethanol | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX E LISTStar2-0057-EA Jump to:of the NationalDynetek EuropeEPG| OpenEXLEasleyEthanol Jump

  9. Cardinal Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX E LISTStar Energy LLCLtd Jump to: navigation, search Name: Carbon TradeEthanol LLC Jump

  10. Missouri Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop Inc Jump to: navigation,Mereg GmbH JumpLLC JumpMissouri Ethanol LLC Place:

  11. Ethanol Management Company | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX E LISTStar2-0057-EA Jump to:ofEnia SpA Jump to:Energy TechLtdaEstelarIllinoisEthanol

  12. Horizon Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX E LISTStar2-0057-EA JumpDuimen RiverScoring Tool Jump to:Ethanol LLC Jump to:

  13. Show Me Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EIS ReportEurope GmbH Jump to: navigation,Show Me Ethanol LLC Jump to:

  14. Algodyne Ethanol Energy Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EAand DaltonSolarOpen5 -TelephoneInformation AlgerAlgodyne Ethanol

  15. BlueFire Ethanol | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental JumpInformationBio-GasIllinois: EnergyHills, Connecticut:NgBlueFire Ethanol Jump

  16. Central Indiana Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmentalBowerbank,CammackFLIR Jump to:RAPIDCavallo EnergyOhio: EnergyFalls,Indiana Ethanol

  17. Ethanol Capital Funding | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoopButtePowerEdisto Electric Coop,Erosion Flume Jump to:Ethanol Capital Funding Jump

  18. Ethanol Capital Management | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoopButtePowerEdisto Electric Coop,Erosion Flume Jump to:Ethanol Capital Funding

  19. Kansas Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsource History View NewGuam:onItronKanosh Town Corporation (UtilityEthanol LLC Jump to:

  20. Brazil Ethanol Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop IncIowaWisconsin:Pontiac BiomassInformationSystemsBradfieldBravo WindEthanol

  1. Prairie Ethanol LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceII JumpQuarterly SmartDB-2, BluePoulsen Hybrid, LLCBiofuelsEthanol LLC Jump to:

  2. BlueFire Ethanol | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative FuelsofProgram:Y-12Power, IncBio Centers AnnouncementandBlog BlogBlueFire Ethanol

  3. Alternative Fuels Data Center: Ethanol Fueling Stations

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels Data Center Home Page on Digg FindPortsas aEthanol Benefits andFueling Stations

  4. Image Compression by Back Propagation

    E-Print Network [OSTI]

    Cottrell, Garrison W.

    CHAPTER 9 Image Compression by Back Propagation: An Example of Extensional Programming* GARRISON W the case with the computatiolls associated with basic cognitive pro- cesses such as vision and audition techniques. The technique we employ is known as back propagation. developed by l1umelhart, Hinton

  5. Compressed Gas EHS-2200-WEB

    E-Print Network [OSTI]

    Compressed Gas Safety EHS-2200-WEB Register and launch through http://axess.stanford.edu Course title and STARS number: General Safety & Emergency Preparedness EHS-4200-WEB Chemical Safety for Laboratories EHS-1900-WEB Biosafety EHS-1500-WEB Radiation Safety Training EHS-5250 Laser Safety EHS-4820-WEB

  6. Compressed Gas Cylinder Safe Handling, Use and

    E-Print Network [OSTI]

    Saskatchewan, University of

    Compressed Gas Cylinder Safe Handling, Use and Storage 2012 Workplace Safety and Environmental Protection #12;i College/Unit: Workplace Safety and Environmental Protection Procedure Title: Compressed Gas................................................ 4 7 General Gas Cylinder Information

  7. Compressive multi-mode superresolution display

    E-Print Network [OSTI]

    Heide, Felix

    Compressive displays are an emerging technology exploring the co-design of new optical device configurations and compressive computation. Previously, research has shown how to improve the dynamic range of displays and ...

  8. Advanced Management of Compressed Air Systems

    Office of Energy Efficiency and Renewable Energy (EERE)

    Find out how a compressed air system works and the benefits of optimal compressed air system performance. This training is designed to help end users as well as industry solution providers learn...

  9. The U.S. Dry-Mill Ethanol Industry: Biobased Products and Bioenergy Initiative Success Stories

    SciTech Connect (OSTI)

    2009-10-28

    This fact sheet provides an overview of the history of ethanol production in the United States and describes innovations in dry-mill ethanol production.

  10. Numerical and experimental studies of ethanol flames and autoignition theory for higher alkanes

    E-Print Network [OSTI]

    Saxena, Priyank

    2007-01-01

    of formaldehyde pyrolysis”, Proceedings of Combustionmodeling of ethanol pyrolysis and combustion”, Journal deG.I. , “High-temperature pyrolysis of ethanol”, Soviet

  11. Red wine but not ethanol at low doses can protect against the toxicity of methamphetamine

    E-Print Network [OSTI]

    Bondy, Stephen Bondy C

    2010-01-01

    C.F. , Chen, C. , 2002. Melatonin in concentrated ethanoland ethanol alone attenuate methamphetamine-induced dopaminewine polyphenol, attenuates ethanol-induced oxidative stress

  12. Low-Cost Hydrogen-from-Ethanol: A Distributed Production System...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low-Cost Hydrogen-from-Ethanol: A Distributed Production System (Presentation) Low-Cost Hydrogen-from-Ethanol: A Distributed Production System (Presentation) Presented at the 2007...

  13. Key Benefits in Using Ethanol-Diesel Blends | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Benefits in Using Ethanol-Diesel Blends Key Benefits in Using Ethanol-Diesel Blends Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER...

  14. Red wine but not ethanol at low doses can protect against the neurotoxicity of methamphetamine

    E-Print Network [OSTI]

    Bondy, SC; Ali, SF

    2010-01-01

    C.F. , Chen, C. , 2002. Melatonin in concentrated ethanoland ethanol alone attenuate methamphetamine-induced dopaminewine polyphenol, attenuates ethanol-induced oxidative stress

  15. Investigation of Bio-Ethanol Steam Reforming over Cobalt-based...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bio-Ethanol Steam Reforming over Cobalt-based Catalysts (Presentation) Investigation of Bio-Ethanol Steam Reforming over Cobalt-based Catalysts (Presentation) Presented at the 2007...

  16. A Pre-Treatment Model for Ethanol Production Using a Colorimetric...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    A Pre-Treatment Model for Ethanol Production Using a Colorimetric Analysis of Starch Solutions (1 Activity) A Pre-Treatment Model for Ethanol Production Using a Colorimetric...

  17. Making Better Use of Ethanol as a Transportation Fuel With "Renewable...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Making Better Use of Ethanol as a Transportation Fuel With "Renewable Super Premium" Making Better Use of Ethanol as a Transportation Fuel With "Renewable Super Premium" Breakout...

  18. Impact of ethanol and butanol as oxygenates on SIDI engine efficiency...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ethanol and butanol as oxygenates on SIDI engine efficiency and emissions using steady-state and transient test procedures Impact of ethanol and butanol as oxygenates on SIDI...

  19. Development of an SI DI Ethanol Optimized Flex Fuel Engine Using...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    an SI DI Ethanol Optimized Flex Fuel Engine Using Advanced Valvetrain Development of an SI DI Ethanol Optimized Flex Fuel Engine Using Advanced Valvetrain Presentation given at the...

  20. Direct and correlated responses to selection for larval ethanol tolerance in Drosophila melanogaster

    E-Print Network [OSTI]

    Fry, James D.

    heterogeneity; phenotypic plasticity; polymorphism; trade-offs. Abstract Ethanol is an important larval resource and toxin for natural Drosophila melanogaster populations, and ethanol tolerance is genetically variable

  1. Greenhouse gases in the corn-to-fuel ethanol pathway.

    SciTech Connect (OSTI)

    Wang, M. Q.

    1998-06-18

    Argonne National Laboratory (ANL) has applied its Greenhouse gas, Regulated Emissions and Energy in Transportation (GREET) full-fuel-cycle analysis model to examine greenhouse gas (GHG) emissions of corn-feedstock ethanol, given present and near-future production technology and practice. On the basis of updated information appropriate to corn farming and processing operations in the four principal corn- and ethanol-producing states (Illinois, Iowa, Minnesota, and Nebraska), the model was used to estimate energy requirements and GHG emissions of corn farming; the manufacture, transportation to farms, and field application of fertilizer and pesticide; transportation of harvested corn to ethanol plants; nitrous oxide emissions from cultivated cornfields; ethanol production in current average and future technology wet and dry mills; and operation of cars and light trucks using ethanol fuels. For all cases examined on the basis of mass emissions per travel mile, the corn-to-ethanol fuel cycle for Midwest-produced ethanol used in both E85 and E10 blends with gasoline outperforms conventional (current) and reformulated (future) gasoline with respect to energy use and GHG production. Also, GHG reductions (but not energy use) appear surprisingly sensitive to the value chosen for combined soil and leached N-fertilizer conversion to nitrous oxide. Co-product energy-use attribution remains the single key factor in estimating ethanol's relative benefits because this value can range from 0 to 50%, depending on the attribution method chosen.

  2. Thermodynamics of the Corn-Ethanol Biofuel Cycle

    E-Print Network [OSTI]

    Patzek, Tadeusz W.

    Thermodynamics of the Corn-Ethanol Biofuel Cycle Tad W. Patzek Department of Civil Sustainability & Renewability 28 1 Introduction 28 2 Disclaimer 28 #12;ii Thermodynamics of corn-ethanol biofuel. . . Web Version 3 Preliminaries 29 4 Laws of Thermodynamics 29 5 Thermodynamics and Economics 31 6

  3. Towards the optimal integrated production of biodiesel with internal recycling of methanol

    E-Print Network [OSTI]

    Grossmann, Ignacio E.

    the use of autoreforming for a production cost 0f $0.61/gal, 3.34MJ/gal of energy consumption and 0.79gal1 Towards the optimal integrated production of biodiesel with internal recycling of methanol of the production methanol from glycerol and its integration in the production of biodiesel from algae. We propose

  4. Methane-to-Methanol Conversion by Gas-Phase Transition Metal Oxide Cations: Experiment and Theory

    E-Print Network [OSTI]

    Metz, Ricardo B.

    Methane-to-Methanol Conversion by Gas-Phase Transition Metal Oxide Cations: Experiment and Theory-phase transition metal oxide cations can convert methane to methanol. Methane activation by MO+ is discussed reaction are also presented. Introduction The direct oxidation of methane to an easily transportable liquid

  5. APPLICATION OF MEMS TECHNOLOGY TO MICRO DIRECT METHANOL FUEL CELL Xiaowei Liu*

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    APPLICATION OF MEMS TECHNOLOGY TO MICRO DIRECT METHANOL FUEL CELL Xiaowei Liu* , Chunguang Suo, email: lxw@hit.edu.cn) ABSTRACT In view of micro fuel cells, the silicon processes are employed for microfabrication of the micro direct methanol fuel cell (DMFC). Using the MEMS technology we have successfully made

  6. Hydrogen Bond Dissociation and Reformation in Methanol Oligomers Following Hydroxyl Stretch Relaxation

    E-Print Network [OSTI]

    Fayer, Michael D.

    Hydrogen Bond Dissociation and Reformation in Methanol Oligomers Following Hydroxyl Stretch, 2002 Vibrational relaxation and hydrogen bond dynamics in methanol-d dissolved in CCl4 have been-d molecules both accepting and donating hydrogen bonds at 2500 cm-1 . Following vibrational relaxation

  7. Experimental Observations in the Morita Baylis-Hillman Reaction in Methanol 

    E-Print Network [OSTI]

    Plata, Robert Erik

    2013-05-22

    -energy profile for a Morita Baylis-Hillman reaction in methanol. Although the majority of this dissertation will be about the Morita Baylis-Hillman reaction in methanol, it could not have been fully accomplished without having to study the Morita Baylis...

  8. The Reactivity Limit for Methanol Oxidation on Platinum/Ruthenium Catalysts

    E-Print Network [OSTI]

    The Reactivity Limit for Methanol Oxidation on Platinum/Ruthenium Catalysts A. Wieckowski 0.5 1.0 1.5 2.0 2.5 3.0 Pt/Ru Decorated (UIUC) PtRu Alloy (JM) E = 0.4 V Oxidation in 0.5 M Methanol

  9. Methanol masers : Reliable tracers of the early stages of high-mass star formation

    E-Print Network [OSTI]

    S. P. Ellingsen

    2005-10-07

    The GLIMPSE and MSX surveys have been used to examine the mid-infrared properties of a statistically complete sample of 6.7 GHz methanol masers. The GLIMPSE point sources associated with methanol masers are clearly distinguished from the majority, typically having extremely red mid-infrared colors, similar to those expected of low-mass class 0 young stellar objects. The intensity of the GLIMPSE sources associated with methanol masers is typically 4 magnitudes brighter at 8.0 micron than at 3.6 micron. Targeted searches towards GLIMPSE point sources with [3.6]-[4.5] > 1.3 and an 8.0 micron magnitude less than 10 will detect more than 80% of class II methanol masers. Many of the methanol masers are associated with sources within infrared dark clouds (IRDC) which are believed to mark regions where high-mass star formation is in its very early stages. The presence of class II methanol masers in a significant fraction of IRDC suggests that high-mass star formation is common in these regions. Different maser species are thought to trace different evolutionary phases of the high-mass star formation process. Comparison of the properties of the GLIMPSE sources associated with class II methanol masers and other maser species shows interesting trends, consistent with class I methanol masers tracing a generally earlier evolutionary phase and OH masers tracing a later evolutionary phase.

  10. Aalborg Universitet Methanol Reformer System Modeling and Control using an Adaptive Neuro-Fuzzy

    E-Print Network [OSTI]

    Andreasen, Sřren Juhl

    by a catalytic burner, which uses the excess hydrogen of the fuel cell. Figure 1 shows the reformer and fuel cellAalborg Universitet Methanol Reformer System Modeling and Control using an Adaptive Neuro., & Sahlin, S. L. (2012). Methanol Reformer System Modeling and Control using an Adaptive Neuro

  11. Aalborg Universitet Dynamic Modeling of a Reformed Methanol Fuel Cell System using Empirical Data and

    E-Print Network [OSTI]

    Berning, Torsten

    Aalborg Universitet Dynamic Modeling of a Reformed Methanol Fuel Cell System using Empirical Data Reza Published in: Journal of Fuel Cell Science and Technology DOI (link to publication from Publisher. K., Andreasen, S. J., & Shaker, H. R. (2014). Dynamic Modeling of a Reformed Methanol Fuel Cell

  12. JOURNAL OF CATALYSIS 92, 127-135 (1985) Oxidative Dehydrogenation of Methanol to Formaldehyde'

    E-Print Network [OSTI]

    Goddard III, William A.

    1985-01-01

    JOURNAL OF CATALYSIS 92, 127-135 (1985) Oxidative Dehydrogenation of Methanol to Formaldehyde/mol at 275°C (I). Because of the extreme industrial impor- tance of formaldehyde for plastics, dyes, etc con- cepts are generally accepted regarding the oxidation of methanol to formaldehyde over Mo03: (a

  13. Aalborg Universitet Control and experimental characterization of a methanol reformer for a 350W high

    E-Print Network [OSTI]

    Berning, Torsten

    , Pontoppidanstrćde 101, 9220 Aalborg East, Denmarkp gy gy g y pp g Introd ction Steam reforming of methanol for a HTPEM f el cell stack ConclusionsIntroduction Steam reforming of methanol for a HTPEM fuel cell stack where heating, conduct detailed measurements of the fuel cells offer many evaporation and superheating

  14. Ethanol oxidation on metal oxide-supported platinum catalysts

    SciTech Connect (OSTI)

    L. M. Petkovic 090468; Sergey N. Rashkeev; D. M. Ginosar

    2009-09-01

    Ethanol is a renewable fuel that can be used as an additive to gasoline (or its substitute) with the advantage of octane enhancement and reduced carbon monoxide exhaust emissions. However, on Ethanol is a renewable fuel that can be used as an additive to gasoline (or its substitute) with the advantage of octane enhancement and reduced carbon monoxide exhaust emissions. However, on the standard three-way catalysts, the conversion of unburned ethanol is low because both ethanol and some of its partially oxidized derivatives are highly resistant to oxidation. A combination of first-principles density-functional theory (DFT) based calculations and in-situ diffuse reflectance infrared spectroscopy (DRIFTS) analysis was applied to uncover some of the fundamental phenomena associated with ethanol oxidation on Pt containing catalysts. In particular, the objective was to analyze the role of the oxide (i.e., ?-Al2O3 or SiO2) substrate on the ethanol oxidation activity. The results showed that Pt nanoparticles trap and accumulate oxygen at their surface and perimeter sites and play the role of “stoves” that burn ethanol molecules and their partially oxidized derivatives to the “final” products. The ?-Al2O3 surfaces provided higher mobility of the fragments of ethanol molecules than the SiO2 surface and hence increased the supply rate of these objects to the Pt particles. This will in turn produce a higher conversion rate of unburned ethanol.and some of its partially oxidized derivatives are highly resistant to oxidation. A combination of first-principles density-functional theory (DFT) based calculations and in-situ diffuse reflectance infrared spectroscopy (DRIFTS) analysis was applied to uncover some of the fundamental phenomena associated with ethanol oxidation on Pt containing catalysts. In particular, the objective was to analyze the role of the oxide (i.e., ?-Al2O3 or SiO2) substrate on the ethanol oxidation activity. The results showed that Pt nanoparticles trap and accumulate oxygen at their surface and perimeter sites and play the role of “stoves” that burn ethanol molecules and their partially oxidized derivatives to the “final” products. The ?-Al2O3 surfaces provided higher mobility of the fragments of ethanol molecules than the SiO2 surface and hence increased the supply rate of these objects to the Pt particles. This will in turn produce a higher conversion rate of unburned ethanol.

  15. ADVANCED RECIPROCATING COMPRESSION TECHNOLOGY (ARCT)

    SciTech Connect (OSTI)

    Danny M. Deffenbaugh; Klaus Brun; Ralph E. Harris; J. Pete Harrell; Robert J. Mckee; J. Jeffrey Moore; Steven J. Svedeman; Anthony J. Smalley; Eugene L. Broerman; Robert A Hart; Marybeth G. Nored; Ryan S. Gernentz; Shane P. Siebenaler

    2005-12-01

    The U.S. natural gas pipeline industry is facing the twin challenges of increased flexibility and capacity expansion. To meet these challenges, the industry requires improved choices in gas compression to address new construction and enhancement of the currently installed infrastructure. The current fleet of installed reciprocating compression is primarily slow-speed integral machines. Most new reciprocating compression is and will be large, high-speed separable units. The major challenges with the fleet of slow-speed integral machines are: limited flexibility and a large range in performance. In an attempt to increase flexibility, many operators are choosing to single-act cylinders, which are causing reduced reliability and integrity. While the best performing units in the fleet exhibit thermal efficiencies between 90% and 92%, the low performers are running down to 50% with the mean at about 80%. The major cause for this large disparity is due to installation losses in the pulsation control system. In the better performers, the losses are about evenly split between installation losses and valve losses. The major challenges for high-speed machines are: cylinder nozzle pulsations, mechanical vibrations due to cylinder stretch, short valve life, and low thermal performance. To shift nozzle pulsation to higher orders, nozzles are shortened, and to dampen the amplitudes, orifices are added. The shortened nozzles result in mechanical coupling with the cylinder, thereby, causing increased vibration due to the cylinder stretch mode. Valve life is even shorter than for slow speeds and can be on the order of a few months. The thermal efficiency is 10% to 15% lower than slow-speed equipment with the best performance in the 75% to 80% range. The goal of this advanced reciprocating compression program is to develop the technology for both high speed and low speed compression that will expand unit flexibility, increase thermal efficiency, and increase reliability and integrity. Retrofit technologies that address the challenges of slow-speed integral compression are: (1) optimum turndown using a combination of speed and clearance with single-acting operation as a last resort; (2) if single-acting is required, implement infinite length nozzles to address nozzle pulsation and tunable side branch absorbers for 1x lateral pulsations; and (3) advanced valves, either the semi-active plate valve or the passive rotary valve, to extend valve life to three years with half the pressure drop. This next generation of slow-speed compression should attain 95% efficiency, a three-year valve life, and expanded turndown. New equipment technologies that address the challenges of large-horsepower, high-speed compression are: (1) optimum turndown with unit speed; (2) tapered nozzles to effectively reduce nozzle pulsation with half the pressure drop and minimization of mechanical cylinder stretch induced vibrations; (3) tunable side branch absorber or higher-order filter bottle to address lateral piping pulsations over the entire extended speed range with minimal pressure drop; and (4) semi-active plate valves or passive rotary valves to extend valve life with half the pressure drop. This next generation of large-horsepower, high-speed compression should attain 90% efficiency, a two-year valve life, 50% turndown, and less than 0.75 IPS vibration. This program has generated proof-of-concept technologies with the potential to meet these ambitious goals. Full development of these identified technologies is underway. The GMRC has committed to pursue the most promising enabling technologies for their industry.

  16. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite

    DOE Patents [OSTI]

    Tierney, J.W.; Wender, I.; Palekar, V.M.

    1995-01-24

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100--160 C and the pressure range of 40--65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H[sub 2]/CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  17. Analytical quality control of products from conversion of methanol to motor fuel components

    SciTech Connect (OSTI)

    Agabalyan, L.G.; Bondareva, G.V.; Fadeev, V.S.

    1985-12-01

    In the gas-chromatographic analysis of gaseous products and aqueous products and aqueous solutions containing methanol and other highpolarity compounds, supports based on polymeric materials are used. These supports have hydrophobic surfaces, relatively low adsorption capacity and no catalytic activity. The work reported in this paper was aimed at the development of analytical procedures for quality control of the feed (methanol-water mixture) and reaction products in the testing volume required in development of experimental-commercial process technology of motor fuel synthesis from methanol. The objects of investigation were the feed and products in methanol conversion to gasoline. These materials were obtained in a semiworks unit. Analytical control of the feed and products in the manufacture of synthetic gasoline from methanol can be accomplished, it is shown, by combining fluorescent indicator analysis, gas chromatography with a back-purge, and capillary chromatography.

  18. Methanol masers as tools to study high-mass star formation

    E-Print Network [OSTI]

    Michele Pestalozzi

    2007-04-23

    In this contribution I will attempt to show that the study of galactic 6.7 and 12.2GHz methanol masers themselves, as opposed to the use of methanol masers as signposts, can yield important conclusions contributing to the understanding of high-mass star formation. Due to their exclusive association with star formation, methanol masers are the best tools to do this, and their large number allows to probe the entire Galaxy. In particular I will focus on the determination of the luminosity function of methanol masers and on the determination of an unambiguous signature for a circumstellar masing disc seen edge-on. Finally I will try to point out some future fields of research in the study of methanol masers.

  19. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite

    DOE Patents [OSTI]

    Tierney, John W. (Pittsburgh, PA); Wender, Irving (Pittsburgh, PA); Palekar, Vishwesh M. (Pittsburgh, PA)

    1995-01-01

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  20. Adsorption of nitrogen, neopentane, n-hexane, benzene and methanol for the evaluation of pore sizes in

    E-Print Network [OSTI]

    Muzzio, Fernando J.

    Adsorption of nitrogen, neopentane, n-hexane, benzene and methanol for the evaluation of pore sizes-hexane, benzene and methanol adsorption isotherms were determined on ®ve samples of silica grade MCM-41

  1. Increase in ethanol yield via elimination of lactate production in an ethanol-tolerant mutant of Clostridium thermocellum

    SciTech Connect (OSTI)

    Biswas, Ranjita; Prabhu, Sandeep; Lynd, Lee R; Guss, Adam M

    2014-01-01

    Large-scale production of lignocellulosic biofuel is a potential solution to sustainably meet global energy needs. One-step consolidated bioprocessing (CBP) is a potentially advantageous approach for the production of biofuels, but requires an organism capable of hydrolyzing biomass to sugars and fermenting the sugars to ethanol at commercially viable titers and yields. Clostridium thermocellum, a thermophilic anaerobe, can ferment cellulosic biomass to ethanol and organic acids, but low yield, low titer, and ethanol sensitivity remain barriers to industrial production. Here, we deleted the hypoxanthine phosphoribosyltransferase gene in ethanol tolerant strain of C. thermocellum adhE*(EA) in order to allow use of previously developed gene deletion tools, then deleted lactate dehydrogenase (ldh) to redirect carbon flux towards ethanol. Upon deletion of ldh, the adhE*(EA) ldh strain produced 30% more ethanol than wild type on minimal medium. The adhE*(EA) ldh strain retained tolerance to 5% v/v ethanol, resulting in an ethanol tolerant platform strain of C. thermocellum for future metabolic engineering efforts.

  2. Modeling the natural attenuation of benzene in groundwater impacted by ethanol-blended fuels: Effect of ethanol content

    E-Print Network [OSTI]

    Alvarez, Pedro J.

    -source simulations imply that high-ethanol blends (e.g., E85) pose a lower risk of benzene reaching a receptor via gasoline, 15 years for E10, 9 years for E50, and 3 years for E85), indicating greater natural attenuationModeling the natural attenuation of benzene in groundwater impacted by ethanol-blended fuels

  3. Electron-Stimulated Reactions and O-2 Production in Methanol-Covered Amorphous Solid Water Films

    SciTech Connect (OSTI)

    Akin, Minta C.; Petrik, Nikolay G.; Kimmel, Gregory A.

    2009-03-14

    The low-energy, electron-stimulated desorption (ESD) of molecular products from amorphous solid water (ASW) films capped with methanol is investigated versus methanol coverage (0 - 4 x 1015 cm-2) at 50 K using 100 eV incident electrons. The major ESD products from a monolayer of methanol on ASW are quite similar to the ESD products from bulk methanol film: H2, CH4, H2O, C2H6, CO, CH2O, and CH3OH. For 40 ML ASW films, the molecular oxygen, hydrogen, and water ESD yields from the ASW are suppressed with increasing methanol coverage, while the CH3OH ESD yield increases proportionally to the methanol coverage. The suppression of the water ESD products by methanol is consistent with the non-thermal reactions occurring preferentially at or near the ASW/vacuum interface and not in the interior of the film. The water and molecular hydrogen ESD yields from the water layer decrease exponentially with the methanol cap coverage with 1/e constants of ~ 0.6 x 1015 cm-2 and 1.6 x 1015 cm-2, respectively. In contrast, the O2 ESD from the water layer is very efficiently quenched by small amounts of methanol (1/e ~ 6.5 x 1013 cm-2). The rapid suppression of O2 production by small amounts of methanol is due to reactions between CH3OH and the precursors for the O2 - mainly OH radicals. A kinetic model for the O2 ESD which semi-quantitatively accounts for the observations is presented.

  4. Detection of 6.7 GHz methanol absorption towards hot corinos

    E-Print Network [OSTI]

    J. D. Pandian; S. Leurini; K. M. Menten; A. Belloche; P. F. Goldsmith

    2008-08-14

    Methanol masers at 6.7 GHz have been found exclusively towards high-mass star forming regions. Recently, some Class 0 protostars have been found to display conditions similar to what are found in hot cores that are associated with massive star formation. These hot corino sources have densities, gas temperatures, and methanol abundances that are adequate for exciting strong 6.7 GHz maser emission. This raises the question of whether 6.7 GHz methanol masers can be found in both hot corinos and massive star forming regions, and if not, whether thermal methanol emission can be detected. We searched for the 6.7 GHz methanol line towards five hot corino sources in the Perseus region using the Arecibo radio telescope. To constrain the excitation conditions of methanol, we observed thermal submillimeter lines of methanol in the NGC1333-IRAS 4 region with the APEX telescope. We did not detect 6.7 GHz emission in any of the sources, but found absorption against the cosmic microwave background in NGC1333-IRAS 4A and NGC1333-IRAS 4B. Using a large velocity gradient analysis, we modeled the excitation of methanol over a wide range of physical parameters, and verify that the 6.7 GHz line is indeed strongly anti-inverted for densities lower than 10^6 cm^-3. We used the submillimeter observations of methanol to verify the predictions of our model for IRAS 4A by comparison with other CH3OH transitions. Our results indicate that the methanol observations from the APEX and Arecibo telescopes are consistent with dense (n ~ 10^6 cm^-3), cold (T ~ 15-30 K) gas. The lack of maser emission in hot corinos and low-mass protostellar objects in general may be due to densities that are much higher than the quenching density in the region where the radiation field is conducive to maser pumping.

  5. Identification of the Active Species in Photochemical Hole Scavenging Reactions of Methanol on TiO2

    SciTech Connect (OSTI)

    Shen, Mingmin; Henderson, Michael A.

    2011-11-03

    Molecular and dissociative methanol adsorption species were prepared on rutile TiO2(110) surfaces to study photocatalytic oxidation of methanol in ultrahigh vacuum (UHV) using temperature-programmed desorption (TPD). Adsorbed methoxy groups (CH3O-) were found to be the photoactive form of adsorbed methanol converted to adsorbed formaldehyde and a surface OH group by hole-mediated C-H bond cleavage. These results suggest that adsorbed methoxy is the effective hole scavenger in photochemical reactions involving methanol.

  6. Removal of sulfur contaminants in methanol for fuel cell applications

    SciTech Connect (OSTI)

    Lee, S.H.D.; Kumar, R. [Argonne National Lab., IL (United States); Sederquist, R. [International Fuel Cells Corp., South Windsor, CT (United States)

    1996-12-31

    Equilibrium adsorption isotherm and breakthrough data were used to assess feasibility of developing a granular activated carbon (GAC) adsorber for use as a sulfur removal subsystem in transportation fuel cell systems. Results suggest that an on-board GAC adsorber may not be attractive due to size and weight constraints. However, it may be feasible to install this GAC adsorber at methanol distribution stations, where space and weight are not a critical concern. Preliminary economic analysis indicated that the GAC adsorber concept will be attractive if the spent AC can be regenerated for reuse. These preliminary analyses were made on basis of very limited breakthrough data obtained from the bench-scale testing. Optimization on dynamic testing parameters and study on regeneration of spent AC are needed.

  7. Direct Methanol Fuel Cell Prototype Demonstration for Consumer Electronics Applications

    SciTech Connect (OSTI)

    Carlstrom, Charles, M., Jr.

    2009-07-07

    This report is the final technical report for DOE Program DE-FC36-04GO14301 titled “Direct Methanol Fuel Cell Prototype Demonstration for Consumer Electronics Applications”. Due to the public nature of this report some of the content reported in confidential reports and meetings to the DOE is not covered in detail in this report and some of the content has been normalized to not show actual values. There is a comparison of the projects accomplishments with the objectives, an overview of some of the key subsystem work, and a review of the three levels of prototypes demonstrated during the program. There is also a description of the eventual commercial product and market this work is leading towards. The work completed under this program has significantly increased the understanding of how Direct Methanol Fuel Cells (DMFC) can be deployed successfully to power consumer electronic devices. The prototype testing has demonstrated the benefits a direct methanol fuel cell system has over batteries typically used for powering consumer electronic devices. Three generations of prototypes have been developed and tested for performance, robustness and life. The technologies researched and utilized in the fuel cell stack and related subsystems for these prototypes are leveraged from advances in other industries such as the hydrogen fueled PEM fuel cell industry. The work under this program advanced the state of the art of direct methanol fuel cells. The system developed by MTI micro fuel cells aided by this program differs significantly from conventional DMFC designs and offers compelling advantages in the areas of performance, life, size, and simplicity. The program has progressed as planned resulting in the completion of the scope of work and available funding in December 2008. All 18 of the final P3 prototypes builds have been tested and the results showed significant improvements over P2 prototypes in build yield, initial performance, and durability. The systems have demonstrated robust operation when tested at various orientations, temperatures, and humidity levels. Durability testing has progressed significantly over the course of the program. MEA, engine, and system level steady state testing has demonstrated degradation rates acceptable for initial product introduction. Test duration of over 5000 hrs has been achieved at both the MEA and breadboard system level. P3 level prototype life testing on engines (stacks with reactant conditioning) showed degradation rates comparable to carefully constructed lab fixtures. This was a major improvement over the P2 and P1 engine designs, which exhibited substantial reductions in life and performance between the lab cell and the actual engine. Over the course of the work on the P3 technology set, a platform approach was taken to the system design. By working in this direction, a number of product iterations with substantial market potential were identified. Although the main effort has been the development of a prototype charger for consumer electronic devices, multiple other product concepts were developed during the program showing the wide variety of potential applications.

  8. The effects of zirconia morphology on methanol synthesis from CO and H2 over Cu/ZrO2 catalysts: Part I -- Steady-State Studies

    E-Print Network [OSTI]

    Rhodes, Michael J.; Bell, Alexis T.

    2005-01-01

    57001 pt1 The Effects of Zirconia Morphology on MethanolAbstract The effect of zirconia phase on the activity andto methanol. Introduction Zirconia-supported copper exhibits

  9. Formation of water and methanol in star forming molecular clouds

    E-Print Network [OSTI]

    Ankan Das; Kinsuk Acharyya; Sonali Chakrabarti; Sandip Kumar Chakrabarti

    2008-06-29

    We study the formation of water and methanol in the dense cloud conditions to find the dependence of its production rate on the binding energies, reaction mechanisms, temperatures, and grain site number. We wish to find the effective grain surface area available for chemical reaction and the effective recombination timescales as functions of grain and gas parameters. We used a Monte Carlo simulation to follow the chemical processes occurring on the grain surface. We find that the formation rate of various molecules is strongly dependent on the binding energies. When the binding energies are high, it is very difficult to produce significant amounts of the molecular species. Instead, the grain is found to be full of atomic species. The production rates are found to depend on the number density in the gas phase. We show that the concept of the effective grain surface area, which we introduced in our earlier work, plays a significant role in grain chemistry. We compute the abundance of water and methanol and show that the results strongly depend on the density and composition in the gas phase, as well as various grain parameters. In the rate equation, it is generally assumed that the recombination efficiencies are independent of the grain parameters, and the surface coverage. Presently, our computed parameter $\\alpha$ for each product is found to depend on the accretion rate, the grain parameters and the surface coverage of the grain. We compare our results obtained from the rate equation and the one from the effective rate equation, which includes $\\alpha$. At the end we compare our results with the observed abundances.

  10. Palladium catalysts synthesized by atomic layer deposition for methanol decomposition.

    SciTech Connect (OSTI)

    Elam, J. W.; Feng, H.; Stair, P. C.; Libera, J. A.; Setthapun, W.; Northwestern Univ.

    2010-05-25

    Atomic layer deposition (ALD) palladium films were deposited at 200 C on various ALD metal oxide surfaces using sequential exposures to Pd(II) hexafluoroacetylacetonate (Pd(hfac)2) and formalin. In situ quartz crystal microbalance measurements as well as ex situ measurements performed on planar substrates revealed that the Pd growth begins with a relatively slow nucleation process and accelerates once an adequate amount of Pd has deposited on the surface. Furthermore, the Pd nucleation is faster on ALD ZnO surfaces compared to ALD Al2O3 surfaces. ALD was utilized to synthesize highly dispersed, uniform Pd nanoparticles (1 to 2 nm in diameter) on ALD ZnO and Al2O3 coated mesoporous silica gel, and the catalytic performances of these samples were compared in the methanol decomposition reaction. The ALD Pd-Al2O3 showed high activity and hydrogen selectivity at relatively low temperatures while the ALD Pd-ZnO showed very low activity as well as quick deactivation. In situ extended X-ray absorption fine structure (EXAFS) measurement revealed that the Pd supported on ZnO 'dissolves' into the substrate during the methanol decomposition reaction which accounts for the gradual disappearance of its catalytic activity. By applying one cycle of ALD Al2O3 on top of the Pd-ZnO catalyst, the activity was enhanced and the catalyst deactivation was mitigated. This Al2O3 overcoating method stabilizes the Pd-ZnO and effectively prevents the dissolution of Pd into the ZnO substrate.

  11. Conservative regularization of compressible flow

    E-Print Network [OSTI]

    Krishnaswami, Govind S; Thyagaraja, Anantanarayanan

    2015-01-01

    Ideal Eulerian flow may develop singularities in vorticity w. Navier-Stokes viscosity provides a dissipative regularization. We find a local, conservative regularization - lambda^2 w times curl(w) of compressible flow and compressible MHD: a three dimensional analogue of the KdV regularization of the one dimensional kinematic wave equation. The regulator lambda is a field subject to the constitutive relation lambda^2 rho = constant. Lambda is like a position-dependent mean-free path. Our regularization preserves Galilean, parity and time-reversal symmetries. We identify locally conserved energy, helicity, linear and angular momenta and boundary conditions ensuring their global conservation. Enstrophy is shown to remain bounded. A swirl velocity field is identified, which transports w/rho and B/rho generalizing the Kelvin-Helmholtz and Alfven theorems. A Hamiltonian and Poisson bracket formulation is given. The regularized equations are used to model a rotating vortex, channel flow, plane flow, a plane vortex ...

  12. Chapter 22: Compressed Air Evaluation Protocol

    SciTech Connect (OSTI)

    Benton, N.

    2014-11-01

    Compressed-air systems are used widely throughout industry for many operations, including pneumatic tools, packaging and automation equipment, conveyors, and other industrial process operations. Compressed-air systems are defined as a group of subsystems composed of air compressors, air treatment equipment, controls, piping, pneumatic tools, pneumatically powered machinery, and process applications using compressed air. A compressed-air system has three primary functional subsystems: supply, distribution, and demand. Air compressors are the primary energy consumers in a compressed-air system and are the primary focus of this protocol. The two compressed-air energy efficiency measures specifically addressed in this protocol are: high-efficiency/variable speed drive (VSD) compressor replacing modulating compressor; compressed-air leak survey and repairs. This protocol provides direction on how to reliably verify savings from these two measures using a consistent approach for each.

  13. Recovery Act: Advanced Direct Methanol Fuel Cell for Mobile Computing

    SciTech Connect (OSTI)

    Fletcher, James H.; Cox, Philip; Harrington, William J; Campbell, Joseph L

    2013-09-03

    ABSTRACT Project Title: Recovery Act: Advanced Direct Methanol Fuel Cell for Mobile Computing PROJECT OBJECTIVE The objective of the project was to advance portable fuel cell system technology towards the commercial targets of power density, energy density and lifetime. These targets were laid out in the DOE’s R&D roadmap to develop an advanced direct methanol fuel cell power supply that meets commercial entry requirements. Such a power supply will enable mobile computers to operate non-stop, unplugged from the wall power outlet, by using the high energy density of methanol fuel contained in a replaceable fuel cartridge. Specifically this project focused on balance-of-plant component integration and miniaturization, as well as extensive component, subassembly and integrated system durability and validation testing. This design has resulted in a pre-production power supply design and a prototype that meet the rigorous demands of consumer electronic applications. PROJECT TASKS The proposed work plan was designed to meet the project objectives, which corresponded directly with the objectives outlined in the Funding Opportunity Announcement: To engineer the fuel cell balance-of-plant and packaging to meet the needs of consumer electronic systems, specifically at power levels required for mobile computing. UNF used existing balance-of-plant component technologies developed under its current US Army CERDEC project, as well as a previous DOE project completed by PolyFuel, to further refine them to both miniaturize and integrate their functionality to increase the system power density and energy density. Benefits of UNF’s novel passive water recycling MEA (membrane electrode assembly) and the simplified system architecture it enabled formed the foundation of the design approach. The package design was hardened to address orientation independence, shock, vibration, and environmental requirements. Fuel cartridge and fuel subsystems were improved to ensure effective fuel containment. PROJECT OVERVIEW The University of North Florida (UNF), with project partner the University of Florida, recently completed the Department of Energy (DOE) project entitled “Advanced Direct Methanol Fuel Cell for Mobile Computing”. The primary objective of the project was to advance portable fuel cell system technology towards the commercial targets as laid out in the DOE R&D roadmap by developing a 20-watt, direct methanol fuel cell (DMFC), portable power supply based on the UNF innovative “passive water recovery” MEA. Extensive component, sub-system, and system development and testing was undertaken to meet the rigorous demands of the consumer electronic application. Numerous brassboard (nonpackaged) systems were developed to optimize the integration process and facilitating control algorithm development. The culmination of the development effort was a fully-integrated, DMFC, power supply (referred to as DP4). The project goals were 40 W/kg for specific power, 55 W/l for power density, and 575 Whr/l for energy density. It should be noted that the specific power and power density were for the power section only, and did not include the hybrid battery. The energy density is based on three, 200 ml, fuel cartridges, and also did not include the hybrid battery. The results show that the DP4 system configured without the methanol concentration sensor exceeded all performance goals, achieving 41.5 W/kg for specific power, 55.3 W/l for power density, and 623 Whr/l for energy density. During the project, the DOE revised its technical targets, and the definition of many of these targets, for the portable power application. With this revision, specific power, power density, specific energy (Whr/kg), and energy density are based on the total system, including fuel tank, fuel, and hybridization battery. Fuel capacity is not defined, but the same value is required for all calculations. Test data showed that the DP4 exceeded all 2011 Technical Status values; for example, the DP4 energy density was 373 Whr/l versus the DOE 2011 status of 200 Whr/l. For the

  14. Compressed air energy storage system

    DOE Patents [OSTI]

    Ahrens, Frederick W. (Naperville, IL); Kartsounes, George T. (Naperville, IL)

    1981-01-01

    An internal combustion reciprocating engine is operable as a compressor during slack demand periods utilizing excess power from a power grid to charge air into an air storage reservoir and as an expander during peak demand periods to feed power into the power grid utilizing air obtained from the air storage reservoir together with combustible fuel. Preferably the internal combustion reciprocating engine is operated at high pressure and a low pressure turbine and compressor are also employed for air compression and power generation.

  15. Sugar-Based Ethanol Biorefinery: Ethanol, Succinic Acid and By-Product Production

    SciTech Connect (OSTI)

    Donal F. Day

    2009-03-31

    The work conducted in this project is an extension of the developments itemized in DE-FG-36-04GO14236. This program is designed to help the development of a biorefinery based around a raw sugar mill, which in Louisiana is an underutilized asset. Some technical questions were answered regarding the addition of a biomass to ethanol facility to existing sugar mills. The focus of this work is on developing technology to produce ethanol and valuable by-products from bagasse. Three major areas are addressed, feedstock storage, potential by-products and the technology for producing ethanol from dilute ammonia pre-treated bagasse. Sugar mills normally store bagasse in a simple pile. During the off season there is a natural degradation of the bagasse, due to the composting action of microorganisms in the pile. This has serious implications if bagasse must be stored to operate a bagasse/biorefinery for a 300+ day operating cycle. Deterioration of the fermentables in bagasse was found to be 6.5% per month, on pile storage. This indicates that long term storage of adequate amounts of bagasse for year-round operation is probably not feasible. Lignin from pretreatment seemed to offer a potential source of valuable by-products. Although a wide range of phenolic compounds were present in the effluent from dilute ammonia pretreatment, the concentrations of each (except for benzoic acid) were too low to consider for extraction. The cellulosic hydrolysis system was modified to produce commercially recoverable quantities of cellobiose, which has a small but growing market in the food process industries. A spin-off of this led to the production of a specific oligosaccharide which appears to have both medical and commercial implications as a fungal growth inhibitor. An alternate use of sugars produced from biomass hydrolysis would be to produce succinic acid as a chemical feedstock for other conversions. An organism was developed which can do this bioconversion, but the economics of succinic acid production were such that it could not compete with current commercial practice. To allow recovery of commercial amounts of ethanol from bagasse fermentation, research was conducted on high solids loading fermentations (using S. cerevisiae) with commercial cellulase on pretreated material. A combination of SHF/SSF treatment with fed-batch operation allowed fermentation at 30% solids loading. Supplementation of the fermentation with a small amount of black-strap molasses had results beyond expectation. There was an enhancement of conversion as well as production of ethanol levels above 6.0% w/w, which is required both for efficient distillation as well as contaminant repression. The focus of fermentation development was only on converting the cellulose to ethanol, as this yeast is not capable of fermenting both glucose and xylose (from hemicellulose). In anticipation of the future development of such an organism, we screened the commercially available xylanases to find the optimum mix for conversion of both cellulose and hemicellulose. A different mixture than the spezyme/novozyme mix used in our fermentation research was found to be more efficient at converting both cellulose and hemicellulose. Efforts were made to select a mutant of Pichia stipitis for ability to co-ferment glucose and xylose to ethanol. New mutation technology was developed, but an appropriate mutant has not yet been isolated. The ability to convert to stillage from biomass fermentations were determined to be suitable for anaerobic degradation and methane production. An economic model of a current sugar factory was developed in order to provide a baseline for the cost/benefit analysis of adding cellulosic ethanol production.

  16. Enhancement of water retention in the membrane electrode assembly for direct methanol fuel cells operating with neat

    E-Print Network [OSTI]

    Zhao, Tianshou

    al. [10], assuming the overall efficiency of the fuel cell system is 20%, the specific energyEnhancement of water retention in the membrane electrode assembly for direct methanol fuel cells 31 July 2010 Keywords: Fuel cell Direct methanol fuel cell (DMFC) Neat-methanol operation Water

  17. In Proc of Direct Methanol Fuel Cell Symposium, 199th Electrochem.l Soc. Mtg, Washington DC, 3/01.

    E-Print Network [OSTI]

    Wang, Chao-Yang

    In Proc of Direct Methanol Fuel Cell Symposium, 199th Electrochem.l Soc. Mtg, Washington DC, 3/01. MATHEMATICAL MODELING OF LIQUID-FEED DIRECT METHANOL FUEL CELLS Z. H. Wang and C. Y. Wang Electrochemical methanol fuel cells (DMFC). Diffusion and convection of both gas and liquid phases are considered

  18. arXiv:0812.0905v2[astro-ph]9Dec2008 Distances to Galactic methanol masers

    E-Print Network [OSTI]

    van Langevelde, Huib Jan

    arXiv:0812.0905v2[astro-ph]9Dec2008 Distances to Galactic methanol masers Kazi L. J. Rygl Max parallax measurements of 6.7 GHz methanol masers in star forming regions of the Galaxy. The 6.7 GHz methanol maser transition is a very valuable astrometric tool, for its large stability and confined

  19. Digestion of milk protein and methanol-grown bacteria protein in the preruminant calf. II. Amino acid composition of

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Digestion of milk protein and methanol-grown bacteria protein in the preruminant calf. II. Amino of milk and of methanol-grown bacteria in the terminal small intestine and the hindgut of the preruminant exclusively by skim-milk powder ; 50.5 p. 100 of the protein of the bacte- ria diet was supplied by methanol

  20. Electrochimica Acta 51 (2006) 54205429 The role of under-rib convection in mass transport of methanol through the

    E-Print Network [OSTI]

    Zhao, Tianshou

    2006-01-01

    of methanol through the serpentine flow field and its neighboring porous layer in a DMFC Q. Ye, T.S. Zhao, C; accepted 11 February 2006 Available online 29 March 2006 Abstract Numerical simulation of a direct methanol, the net electrochemical reactions in the DMFC anode cease, but, owing to the methanol concentration

  1. arXiv:1102.0854v1[astro-ph.GA]4Feb2011 Studies of methanol maser rings

    E-Print Network [OSTI]

    De Buizer, James Michael

    arXiv:1102.0854v1[astro-ph.GA]4Feb2011 Studies of methanol maser rings Anna Bartkiewicz, Marian present the results of studies of a new class of 6.7 GHz methanol maser sources with a ring- like emission-like distribution of methanol maser spots. Using the Gemini telescopes we found mid-infrared (MIR) counterparts

  2. The role of specific solvent modes in the non-radiative relaxation of an excess electron in methanol

    E-Print Network [OSTI]

    in methanol A.A. Mosyak, O.V. Prezhdo1 , P.J. Rossky* Department of Chemistry and Biochemistry, University electronic excited state of an excess electron in methanol. Compared to water, we find that the presence in methanol. The first solvation shell dominates the electronic coupling, most strongly through rotational

  3. Mechanistic Studies of Methanol Oxidation to Formaldehyde on Isolated Vanadate Sites Supported on High Surface Area Zirconia

    E-Print Network [OSTI]

    Bell, Alexis T.

    Mechanistic Studies of Methanol Oxidation to Formaldehyde on Isolated Vanadate Sites Supported, California 94720-1462 ReceiVed: NoVember 20, 2007; In Final Form: February 6, 2008 The oxidation of methanol that the vanadium is present as isolated VO4 units in a distorted tetrahedral geometry. Methanol was found to adsorb

  4. Methanol Reaction with Sulfuric Acid: A Vibrational Spectroscopic Study Lisa L. Van Loon and Heather C. Allen*

    E-Print Network [OSTI]

    Methanol Reaction with Sulfuric Acid: A Vibrational Spectroscopic Study Lisa L. Van Loon 43210 ReceiVed: May 27, 2004; In Final Form: August 19, 2004 The reaction between methanol and sulfuric peak in the 800 cm-1 region, not present in either the neat methanol or concentrated sulfuric acid

  5. Water and Methanol Adsorption on MgO(100)/Mo(100) Studied by Electron Spectroscopies and Thermal Programmed Desorption

    E-Print Network [OSTI]

    Goodman, Wayne

    Water and Methanol Adsorption on MgO(100)/Mo(100) Studied by Electron Spectroscopies and Thermal, 2000 The adsorption of methanol (CH3OH) and water (D2O) on the MgO(100)/Mo(100) surface at 100 K has covered MgO(100)/Mo(100) surface. On the other hand, the formation of a methanol multilayer desorption

  6. Journal of Power Sources 164 (2007) 189195 Modeling water transport in liquid feed direct methanol fuel cells

    E-Print Network [OSTI]

    2007-01-01

    Journal of Power Sources 164 (2007) 189­195 Modeling water transport in liquid feed direct methanol management in direct methanol fuel cells (DMFCs) is very critical and complicated because of many interacting rights reserved. Keywords: Direct methanol fuel cell; Water transport; Mathematical modeling; Three

  7. Effect of surface composition of Pt-Au alloy cathode catalyst on the performance of direct methanol fuel cells

    E-Print Network [OSTI]

    Zhao, Tianshou

    Effect of surface composition of Pt-Au alloy cathode catalyst on the performance of direct methanol 2010 Available online 12 June 2010 Keywords: Fuel cell Direct methanol fuel cell Catalyst Active Site Pt-Au alloy a b s t r a c t A pure Pt cathode catalyst in direct methanol fuel cells is not only

  8. Interaction of methanol and water on MgO,,100... studied by ultraviolet photoelectron and metastable impact electron spectroscopies

    E-Print Network [OSTI]

    Goodman, Wayne

    Interaction of methanol and water on MgO,,100... studied by ultraviolet photoelectron; accepted 27 October 1998 The coadsorption of methanol (CH3OH) and water (D2O) on the MgO 100 /Mo 100 photoelectron spectroscopy UPS HeI , and by thermal programmed desorption TPD . Methanol wets the MgO surface

  9. Methanol as a Sensitive Probe for Spatial and Temporal Variations of the Proton-to-Electron Mass Ratio

    E-Print Network [OSTI]

    Methanol as a Sensitive Probe for Spatial and Temporal Variations of the Proton-to-Electron Mass, corresponding to the 51 ! 60Aţ and 20 ! 3Ŕ1E transitions in methanol (CH3OH), respectively, are among transitions in the ground state of methanol to a variation of the proton-to- electron mass ratio. We show

  10. Mechanistic Studies of Methanol Oxidation to Formaldehyde on Isolated Vanadate Sites Supported on High Surface Area Anatase

    E-Print Network [OSTI]

    Bell, Alexis T.

    Mechanistic Studies of Methanol Oxidation to Formaldehyde on Isolated Vanadate Sites Supported for methanol oxidation on both TiO2 and V/TiO2 was investigated using temperature- programmed experiments/TiO2 sample consists predominantly of isolated VO4 units after calcination. Methanol was found

  11. arXiv:0812.0905v1[astro-ph]4Dec2008 Distances to Galactic methanol masers

    E-Print Network [OSTI]

    Brunthaler, Andreas

    arXiv:0812.0905v1[astro-ph]4Dec2008 Distances to Galactic methanol masers Kazi L. J. RyglŁ Max parallax measurements of 6.7 GHz methanol masers in star forming regions of the Galaxy. The 6.7 GHz methanol maser transition is a very valuable astrometric tool, for its large stability and confined

  12. Effects of Methanol on the Thermodynamics of Iron(III) [Tetrakis(pentafluorophenyl)]porphyrin Chloride Dissociation and the

    E-Print Network [OSTI]

    Bell, Alexis T.

    Effects of Methanol on the Thermodynamics of Iron(III) [Tetrakis in acetonitrile but is catalytically active if the solvent contains methanol. It was suggested that the precursor to the active species is (F20TPP)Fe(OCH3) in methanol-containing solvents. The present study was aimed

  13. 976 JOURNAL OF MICROELECTROMECHANICAL SYSTEMS, VOL. 15, NO. 4, AUGUST 2006 Methanol Steam Reformer on a Silicon Wafer

    E-Print Network [OSTI]

    Malen, Jonathan A.

    of the reforming rates, heat transfer and flow through a methanol reforming catalytic microreactor fabri- cated976 JOURNAL OF MICROELECTROMECHANICAL SYSTEMS, VOL. 15, NO. 4, AUGUST 2006 Methanol Steam Reformer is achieved through on-chip resis- tive heaters, whereby methanol steam reforming reactions were studied over

  14. Stripping ethanol from ethanol-blended fuels for use in NO.sub.x SCR

    DOE Patents [OSTI]

    Kass, Michael Delos (Oak Ridge, TN); Graves, Ronald Lee (Knoxville, TN); Storey, John Morse Elliot (Oak Ridge, TN); Lewis, Sr., Samuel Arthur (Andersonville, TN); Sluder, Charles Scott (Knoxville, TN); Thomas, John Foster (Powell, TN)

    2007-08-21

    A method to use diesel fuel alchohol micro emulsions (E-diesel) to provide a source of reductant to lower NO.sub.x emissions using selective catalytic reduction. Ethanol is stripped from the micro emulsion and entered into the exhaust gasses upstream of the reducing catalyst. The method allows diesel (and other lean-burn) engines to meet new, lower emission standards without having to carry separate fuel and reductant tanks.

  15. Recombinant host cells and media for ethanol production

    DOE Patents [OSTI]

    Wood, Brent E; Ingram, Lonnie O; Yomano, Lorraine P; York, Sean W

    2014-02-18

    Disclosed are recombinant host cells suitable for degrading an oligosaccharide that have been optimized for growth and production of high yields of ethanol, and methods of making and using these cells. The invention further provides minimal media comprising urea-like compounds for economical production of ethanol by recombinant microorganisms. Recombinant host cells in accordance with the invention are modified by gene mutation to eliminate genes responsible for the production of unwanted products other than ethanol, thereby increasing the yield of ethanol produced from the oligosaccharides, relative to unmutated parent strains. The new and improved strains of recombinant bacteria are capable of superior ethanol productivity and yield when grown under conditions suitable for fermentation in minimal growth media containing inexpensive reagents. Systems optimized for ethanol production combine a selected optimized minimal medium with a recombinant host cell optimized for use in the selected medium. Preferred systems are suitable for efficient ethanol production by simultaneous saccharification and fermentation (SSF) using lignocellulose as an oligosaccharide source. The invention also provides novel isolated polynucleotide sequences, polypeptide sequences, vectors and antibodies.

  16. Implications of ethanol-based fuels for greenhouse gas emissions

    SciTech Connect (OSTI)

    Marland, G. [Oak Ridge National Lab., TN (United States); DeLuchi, M.A. [Univ. of California, Davis, CA (United States). Inst. of Transportation Studies; Wyman, C. [National Renewable Energy Lab., Golden, CO (United States)

    1994-02-14

    The US Environmental Protection Agency has proposed a rule which would mandate that 30% of the oxygen content of reformulated gasoline be provided by renewable oxygenates. The rule would essentially require that biomass-based ethanol, or ETBE derived from ethanol, be used to supply 30% of the oxygen in reformulated gasoline. This short statement addresses the very narrow question, ``Would this rule result in a net decrease in greenhouse gas emissions?`` The challenge then is to determine how much greenhouse gas is emitted during the ethanol fuel cycle, a fuel cycle that is much less mature and less well documented than the petroleum fuel cycle. In the petroleum fuel cycle, most of the greenhouse gas emissions come from fuel combustion. In the ethanol fuel cycle most of the greenhouse gas emissions come from the fuel production processes. Details of corn productivity, fertilizer use, process efficiency, fuel source, etc. become very important. It is also important that the ethanol fuel cycle produces additional products and the greenhouse gas emissions have somehow to be allocated among the respective products. With so many variables in the ethanol fuel cycle, the concern is actually with ethanol-based additives which will be produced in response to the proposed rule, and not necessarily with the average of ethanol which is being produced now. A first important observation is that the difference between standard gasoline and reformulated gasoline is very small so that when differences are drawn against alternative fuels, it makes little difference whether the contrast is against standard or reformulated gasoline. A second observation is that for this base case comparison, emissions of CO{sub 2} alone are roughly 13% less for the ethanol fuel cycle than for the reformulated gasoline cycle.

  17. Detection of a methanol megamaser in a major-merger galaxy

    E-Print Network [OSTI]

    Chen, Xi; Baan, Willem A; Qiao, Hai-Hua; Li, Juan; An, Tao; Breen, Shari L

    2015-01-01

    We have detected emission from both the 4_{-1}-3_{0} E (36.2~GHz) class I and 7_{-2}-8_{-1} E (37.7~GHz) class II methanol transitions towards the centre of the closest ultra-luminous infrared galaxy Arp 220. The emission in both the methanol transitions show narrow spectral features and have luminosities approximately 8 orders of magnitude stronger than that observed from typical class I methanol masers observed in Galactic star formation regions. The emission is also orders of magnitude stronger than the expected intensity of thermal emission from these transitions and based on these findings we suggest that the emission from the two transitions are masers. These observations provides the first detection of a methanol megamaser in the 36.2 and 37.7 GHz transitions and represents only the second detection of a methanol megamaser, following the recent report of an 84 GHz methanol megamaser in NGC1068. We find the methanol megamasers are significantly offset from the nuclear region and arise towards regions wh...

  18. Impact of Ethanol on Benzene Plume Lengths: Microbial and Modeling Studies

    E-Print Network [OSTI]

    Alvarez, Pedro J.

    plume lengths in subsurface environments following accidental spills of ethanol-blended gasoline. Two, 8% of all the gasoline sold in the United States contained ethanol. By 1998, ethanol-blended fuels. As a result, the use of ethanol-blended gasoline is expected to in- crease in the United States over the next

  19. IEA Implementing Agreement on Advanced Motor Fuels Ethanol as a Fuel for

    E-Print Network [OSTI]

    .................................................................................................... 27 WATER AND BLENDING ISSUES........................................................................................ 28 Ethanol/Gasoline/Water Miscibility

  20. 2010-01-0166 Ethanol Content Estimation in Flex Fuel Direct Injection

    E-Print Network [OSTI]

    Stefanopoulou, Anna

    2010-01-0166 Ethanol Content Estimation in Flex Fuel Direct Injection Engines Using In (FFVs) are able to operate on a blend of ethanol and gasoline in any volumetric concen- tration of up to 85% ethanol (93% in Brazil). The estima- tion of ethanol content is crucial for optimized and robust