Sample records for material balance area

  1. A Water Balance Study of Four Landfill Cover Designs at Material Disposal Area B in Los Alamos, New Mexico

    SciTech Connect (OSTI)

    David D. Breshears; Fairley J. Barnes; John W. Nyhan; Johnny A. Salazar

    1998-09-01T23:59:59.000Z

    The goal of disposing of low-level radioactive and hazardous waste in shallow landfills is to reduce risk to human health and the environment by isolating contaminants until they no longer pose an unacceptable hazard. In order to achieve this, the Department of Energy Environmental Restoration Program is comparing the performance of several different surface covers at Material Disposal Area (MDA) B in Los Alamos. Two conventional landfill were compared with an improved cover designed to minimize plant and animal intrusion and to minimize water infiltration into the underlying wastes. The conventional covers varied in depth and both conventional and improved designs had different combinations of vegetation (grass verses shrub) and gravel mulch (no mulch verses mulch). These treatments were applied to each of 12 plots and water balance parameters were measured from March1987 through June 1995. Adding a gravel mulch significantly influenced the plant covered field plots receiving no gravel mulch averaged 21.2% shrub cover, while plots with gravel had a 20% larger percent cover of shrubs. However, the influence of gravel mulch on the grass cover was even larger than the influence on shrub cover, average grass cover on the plots with no gravel was 16.3%, compared with a 42% increase in grass cover due to gravel mulch. These cover relationships are important to reduce runoff on the landfill cover, as shown by a regression model that predicts that as ground cover is increased from 30 to 90%,annual runoff is reduced from 8.8 to 0.98 cm-a nine-fold increase. We also found that decreasing the slope of the landfill cover from 6 to 2% reduced runoff from the landfill cover by 2.7-fold. To minimize the risk of hazardous waste from landfills to humans, runoff and seepage need to be minimized and evapotranspiration maximized on the landfill cover. This has to be accomplished for dry and wet years at MDA B. Seepage consisted of 1.9% and 6.2% of the precipitation in the average and once in ten year events, respectively, whereas corresponding values for runoff were 13% and 16%; these changes were accompanied by corresponding decreases in evapotranspiration, which accounted for 86% and only 78% of the precipitation occurring on the average and once in ten year even~ respectively.

  2. Course Title: Material and Energy Balances Instructor: Nader Aderangi

    E-Print Network [OSTI]

    Heller, Barbara

    and energy balances for such systems. 7. Draw a process flow chart for a complex chemical system and solve graphically using flow charts, formulate materials and energy balances and solve them. This outcome introduced at the end of the course. Students perform materials and energy balances on a complex flow sheet

  3. Material Disposal Areas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHighand Retrievals from a New 183-GHzMAR Os2010 TeppeiMaterial Disposal

  4. A comparison of material balance calculations based on equilibrium ratios with Schilthuis balance calculations

    E-Print Network [OSTI]

    Clanton, John L

    1956-01-01T23:59:59.000Z

    . This material balance is unique in that it allows the oil reserves to be determined directly, while all previous ones were concerned with cal- culation of oil initially in place. Sage and Lacy introduced an "occlusion factor", which takes 9. account... be used to more accurately esti- mate reserves. In 1943 Gook published a report in which he described the 10 derivation and application of the material balance equation to the Mag- nolia Field and stated that since gas volumes are measured...

  5. Material Balance Report | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment3311, 3312), October 20122 DOE Hydrogenis Winding6 * OctoberMaterial

  6. INVESTIGATING THE SURFACE ENERGY BALANCE IN URBAN AREAS RECENT ADVANCES AND FUTURE NEEDS

    E-Print Network [OSTI]

    Ribes, Aurélien

    INVESTIGATING THE SURFACE ENERGY BALANCE IN URBAN AREAS ­ RECENT ADVANCES AND FUTURE NEEDS M of the surface energy balance of urban areas, based on both experimental investigations and numerical models in urban areas is commonly limited to a few sites, often just at airports. The surface energy balance

  7. Role of Large Balancing Areas In Integrating Solar Generation: Solar Integration Series. 3 of 3 (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2011-05-01T23:59:59.000Z

    The third out of a series of three fact sheets describing the role of large balancing areas in integrating solar generation.

  8. Impact of Balancing Areas Size, Obligation Sharing, and Ramping Capability on Wind Integration: Preprint

    SciTech Connect (OSTI)

    Milligan, M.; Kirby, B.

    2007-06-01T23:59:59.000Z

    This paper examines wind integration costs as a function of balancing area size to determine if the larger system size helps mitigate wind integration cost increases.

  9. Combining Balancing Areas' Variability: Impacts on Wind Integration in the Western Interconnection

    SciTech Connect (OSTI)

    Milligan, M.; Kirby, B.; Beuning, S.

    2010-07-01T23:59:59.000Z

    This paper investigates the potential impact of balancing area cooperation on a large-scale in the Western Electricity Coordinating Council (WECC).

  10. IMPORTANCE OF MATERIAL BALANCES AND THEIR STATISTICAL EVALUATION IN RUSSIAN MATERIAL, PROTECTION, CONTROL AND ACCOUNTING

    SciTech Connect (OSTI)

    FISHBONE,L.G.

    1999-07-25T23:59:59.000Z

    While substantial work has been performed in the Russian MPC&A Program, much more needs to be done at Russian nuclear facilities to complete four necessary steps. These are (1) periodically measuring the physical inventory of nuclear material, (2) continuously measuring the flows of nuclear material, (3) using the results to close the material balance, particularly at bulk processing facilities, and (4) statistically evaluating any apparent loss of nuclear material. The periodic closing of material balances provides an objective test of the facility's system of nuclear material protection, control and accounting. The statistical evaluation using the uncertainties associated with individual measurement systems involved in the calculation of the material balance provides a fair standard for concluding whether the apparent loss of nuclear material means a diversion or whether the facility's accounting system needs improvement. In particular, if unattractive flow material at a facility is not measured well, the accounting system cannot readily detect the loss of attractive material if the latter substantially derives from the former.

  11. Advanced materials research areas | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisiting the TWP TWP Related LinksATHENAAdministrative80-AAAdvancedof Materials Under

  12. Basic science research to support the nuclear material focus area

    SciTech Connect (OSTI)

    Boak, J. M. (Jeremy M.); Eller, P. Gary; Chipman, N. A.; Castle, P. M.

    2002-01-01T23:59:59.000Z

    The Department of Energy's (DOE'S) Office of Environmental Management (EM) is responsible for managing more than 760,000 metric tons of nuclear material that is excess to the current DOE weapons program, as a result of shutdown of elements of the weapons program, mainly during the 1990s. EMowned excess nuclear material comprises a variety of material types, including uranium, plutonium, other actinides and other radioactive elements in numerous forms, all of which must be stabilized for storage and ultimate disposition. Much of this quantity has been in storage for many years. Shutdown of DOE sites and facilities requires removal of nuclear material and consolidation at other sites, and may be delayed by the lack of available technology. Within EM, the Office of Science and Technology (OST) is dedicated to providing timely, relevant technology to accelerate completion and reduce cleanup cost of the DOE environmental legacy. OST is organized around five focus areas, addressing crucial areas of end-user-defined technology need. The Focus Areas regularly identify potential technical solutions for which basic scientific research is needed to determine if the technical solution can be developed and deployed. To achieve a portfolio of projects that is balanced between near-term priorities driven by programmatic risks (such as site closure milestones) and long-term, high-consequence needs that depend on extensive research and development, OST has established the Environmental Management Science Program (EMSP) to develop the scientific basis for solutions to long-term site needs. The EMSP directs calls for proposals to address scientific needs of the focus areas. Needs are identified and validated annually by individual sites in workshops conducted across the complex. The process captures scope and schedule requirements of the sites, so that focus areas can identify technology that can be delivered to sites in time to complete site cleanup. The Nuclear Material Focus Area (NMFA) has identified over two hundred science and technology needs, of which more than thirty are science needs.

  13. Basic Science Research to Support the Nuclear Materials Focus Area

    SciTech Connect (OSTI)

    Chipman, N. A.; Castle, P. M.; Boak, J. M.; Eller, P. G.

    2002-02-26T23:59:59.000Z

    The Department of Energy's (DOE's) Office of Environmental Management (EM) is responsible for managing more than 760,000 metric tons of nuclear material that is excess to the current DOE weapons program, as a result of shutdown of elements of the weapons program, mainly during the 1990s. EMowned excess nuclear material comprises a variety of material types, including uranium, plutonium, other actinides and other radioactive elements in numerous forms, all of which must be stabilized for storage and ultimate disposition. Much of this quantity has been in storage for many years. Shutdown of DOE sites and facilities requires removal of nuclear material and consolidation at other sites, and may be delayed by the lack of available technology. Within EM, the Office of Science and Technology (OST) is dedicated to providing timely, relevant technology to accelerate completion and reduce cleanup cost of the DOE environmental legacy. OST is organized around five focus areas, addressing crucial areas of end-user-defined technology need. The Focus Areas regularly identify potential technical solutions for which basic scientific research is needed to determine if the technical solution can be developed and deployed. To achieve a portfolio of projects that is balanced between near-term priorities driven by programmatic risks (such as site closure milestones) and long-term, high-consequence needs that depend on extensive research and development, OST has established the Environmental Management Science Program (EMSP) to develop the scientific basis for solutions to long-term site needs. The EMSP directs calls for proposals to address scientific needs of the focus areas. Needs are identified and validated annually by individual sites in workshops conducted across the complex. The process captures scope and schedule requirements of the sites, so that focus areas can identify technology that can be delivered to sites in time to complete site cleanup. The Nuclear Material Focus Area (NMFA) has identified over two hundred science and technology needs, of which more than thirty are science needs.

  14. Study of a double bubbler for material balance in liquids

    SciTech Connect (OSTI)

    Hugues Lambert

    2013-09-01T23:59:59.000Z

    The objective of this project was to determine the potential of a double bubbler to measure density and fluid level of the molten salt contained in an electrorefiner. Such in-situ real-time measurements can provide key information for material balances in the pyroprocessing of the nuclear spent fuel. This theoretical study showed this technique has a lot of promise. Four different experiments were designed and performed. The first three experiments studied the influence of a variety of factors such as depth difference between the two tubes, gas flow rate, the radius of the tubes and determining the best operating conditions. The last experiment purpose was to determine the precision and accuracy of the apparatus during specific conditions. The elected operating conditions for the characterization of the system were a difference of depth of 25 cm and a flow rate of 55 ml/min in each tube. The measured densities were between 1,000 g/l and 1,400g/l and the level between 34cm and 40 cm. The depth difference between the tubes is critical, the larger, the better. The experiments showed that the flow rate should be the same in each tube. The concordances with theoretical predictions were very good. The density precision was very satisfying (spread<0.1%) and the accuracy was about 1%. For the level determination, the precision was also very satisfying (spread<0.1%), but the accuracy was about 3%. However, those two biases could be corrected with calibration curves. In addition to the aqueous systems studied in the present work, future work will focus on examining the behavior of the double bubbler instrumentation in molten salt systems. The two main challenges which were identified in this work are the effect of the temperature and the variation of the superficial tension.

  15. Advances in Sustainable Petroleum Engineering Science, Volume 1, Issue 2, 2009, pp. 141 -162 AComprehensiveMaterialBalanceEquationwiththeInclusionof

    E-Print Network [OSTI]

    Hossain, M. Enamul

    techniques, it is time to include all salient features of the material balance equation (MBE). The inclusion predicting petroleum reservoir performance. However, it is well known that the material balance equation AComprehensiveMaterialBalanceEquationwiththeInclusionof MemoryDuringRock-FluidDeformation M.E. Hossain Dalhousie

  16. A study of the validity of early material balance estimates in petroleum reservoirs

    E-Print Network [OSTI]

    Galindo, Christian Anze

    1964-01-01T23:59:59.000Z

    A STUDY OF THE VALIDITY OF EARLY MATERIAL BALANCE ESTIMATES IN PETROLEUM RESERVOIRS A Thesis by CHRISTIAN ANZE GALINDO Submitted to the Graduate College of the Texas ARM University in partia4 fulfillment of the requirements for the degree... of MASTER OF SCIENCE January 1964 Major Subject: Petroleum Engineering A STUDY OF THE VALIDITY OF EARLY MATERIAL BALANCE ESTIMATES IN PETROLEUM RESERVOIRS A Thesis by CHRISTIAN ANZE GALINDO App o ed as to style nd content by. Chairman of Committee...

  17. InAs/InAsSb strain balanced superlattices for optical detectors: Material properties and energy band simulations

    E-Print Network [OSTI]

    Krishna, Sanjay

    InAs/InAsSb strain balanced superlattices for optical detectors: Material properties and energyAs/InAsSb strain balanced superlattices for optical detectors: Material properties and energy band simulations D February 2012) InAsSb/InAs type II strain balanced superlattices lattice matched to GaSb have recently been

  18. Critical Area Computation for Missing Material Defects in VLSI Circuits

    E-Print Network [OSTI]

    Papadopoulou, Evanthia

    Critical Area Computation for Missing Material Defects in VLSI Circuits Evanthia Papadopoulou IBM the problem of computing critical area for miss- ing material defects in a circuit layout. The extraction of critical area is the main computational problem in VLSI yield prediction. Missing material defects cause

  19. Rethinking emergency habitats for refugees : balancing material innovation and culture

    E-Print Network [OSTI]

    Sinisterra, Maria Alexandra, 1975-

    2004-01-01T23:59:59.000Z

    This thesis propose an alternative approach to emergency housing for Colombian refugees, helping development agencies put the displaced community on the road to permanent housing. An environmentally friendly 'smart' material ...

  20. How Protein Materials Balance Strength, Robustness And Adaptability

    E-Print Network [OSTI]

    Buehler, Markus J.

    Proteins form the basis of a wide range of biological materials such as hair, skin, bone, spider silk, or cells, which play an important role in providing key functions to biological systems. The focus of this article is ...

  1. Area balance and strain in coalbed methane reservoirs of the Black Warrior basin

    SciTech Connect (OSTI)

    Pashin, J.C. [Geological Survey of Alabama, Tuscaloosa, AL (United States); Groshong, R.H., Jr. [Univ. of Alabama, Tuscaloosa, AL (United States)

    1996-09-01T23:59:59.000Z

    Investigation of coalbed methane reservoirs in the Black Warrior basin of Alabama has established a correspondence between productivity and structural position, but the reasons for this correspondence remain uncertain. In Cedar Cove field, for example, exceptionally productive wells are concentrated in a rollover anticline, whereas in Oak Grove field, exceptionally productive wells are aligned along a synclinal axis. This suggests that factors controlling gas production are a derivative of the structural geometry, and not the geometry by itself. Natural fractures and a low state of in-situ stress facilitate depressurization of coalbed reservoirs by dewatering, and hence, desorption and production of coalbed gas. Our hypothesis is that the abundance and openness of natural fractures in the Black Warrior basin are a direct expression of the layer-parallel strain dictated by map-scale structural geometry. Area balancing techniques can be used to quantify requisite strain, which is the homogeneous layer-parallel strain required for local area balance, and can also be used to constrain and verify structural cross sections. Application of area balancing techniques to extensional structures in the Black Warrior basin indicates that coalbed gas is produced from thin-skinned structures detached within the coal-bearing Pottsville Formation. Within reservoir intervals, requisite strain values are as high as 10 percent and increase downward toward the basal detachment. Mapping structure and production indicates that some productivity sweet spots correlate with enhanced bed curvature. Whereas requisite strain is the homogeneous strain calculated for discrete bed segments, curvature affects the distribution of strain within those segments. Recognizing this, our research is now focused on integrating area balancing techniques with curvature analysis to explain production patterns in coalbed methane reservoirs.

  2. Global estimation of evapotranspiration using a leaf area index-based surface energy and water balance model

    E-Print Network [OSTI]

    Martin, Timothy

    using Advanced Very High Res- olution Radiometer Lai data, Climate Research Unit climate dataGlobal estimation of evapotranspiration using a leaf area index-based surface energy and water-relative-humidity-based two-source (ARTS) E model that simulates the surface energy balance, soil water balance

  3. Average balance equations, scale dependence, and energy cascade for granular materials

    E-Print Network [OSTI]

    Riccardo Artoni; Patrick Richard

    2015-03-09T23:59:59.000Z

    A new averaging method linking discrete to continuum variables of granular materials is developed and used to derive average balance equations. Its novelty lies in the choice of the decomposition between mean values and fluctuations of properties which takes into account the effect of gradients. Thanks to a local homogeneity hypothesis, whose validity is discussed, simplified balance equations are obtained. This original approach solves the problem of dependence of some variables on the size of the averaging domain obtained in previous approaches which can lead to huge relative errors (several hundred percentages). It also clearly separates affine and nonaffine fields in the balance equations. The resulting energy cascade picture is discussed, with a particular focus on unidirectional steady and fully developed flows for which it appears that the contact terms are dissipated locally unlike the kinetic terms which contribute to a nonlocal balance. Application of the method is demonstrated in the determination of the macroscopic properties such as volume fraction, velocity, stress, and energy of a simple shear flow, where the discrete results are generated by means of discrete particle simulation.

  4. INCREASING STORAGE CAPAPCITY OF DREDGED MATERIAL MANAGEMENT AREAS

    E-Print Network [OSTI]

    INCREASING STORAGE CAPAPCITY OF DREDGED MATERIAL MANAGEMENT AREAS Timothy D. Stark, Ph.D., P 39180 Paper Published in the Proceedings of: 15th Annual Meeting of Western Dredging Association (WEDA XV) San Diego, CA May 1994 #12;2 INCREASING STORAGE CAPAPCITY OF DREDGED MAERIAL MANAGEMENT AREAS

  5. Quantifying object and material surface areas in residences

    SciTech Connect (OSTI)

    Hodgson, Alfred T.; Ming, Katherine Y.; Singer, Brett C.

    2005-01-05T23:59:59.000Z

    The dynamic behavior of volatile organic compounds (VOCs) in indoor environments depends, in part, on sorptive interactions between VOCs in the gas phase and material surfaces. Since information on the types and quantities of interior material surfaces is not generally available, this pilot-scale study was conducted in occupied residences to develop and demonstrate a method for quantifying surface areas of objects and materials in rooms. Access to 33 rooms in nine residences consisting of bathrooms, bedroom/offices and common areas was solicited from among research group members living in the East San Francisco Bay Area. A systematic approach was implemented for measuring rooms and objects from 300 cm{sup 2} and larger. The ventilated air volumes of the rooms were estimated and surface area-to-volume ratios were calculated for objects and materials, each segregated into 20 or more categories. Total surface area-to-volume ratios also were determined for each room. The bathrooms had the highest total surface area-to-volume ratios. Bedrooms generally had higher ratios than common areas consisting of kitchens, living/dining rooms and transitional rooms. Total surface area-to-volume ratios for the 12 bedrooms ranged between 2.3 and 4.7 m{sup 2} m{sup -3}. The importance of individual objects and materials with respect to sorption will depend upon the sorption coefficients for the various VOC/materials combinations. When combined, the highly permeable material categories, which may contribute to significant interactions, had a median ratio of about 0.5 m{sup 2} m{sup -3} for all three types of rooms.

  6. SRS K-AREA MATERIAL STORAGE - EXPANDING CAPABILITIES

    SciTech Connect (OSTI)

    Koenig, R.

    2013-07-02T23:59:59.000Z

    In support of the Department of Energy’s continued plans to de-inventory and reduce the footprint of Cold War era weapons’ material production sites, the K-Area Material Storage (KAMS) facility, located in the K-Area Complex (KAC) at the Savannah River Site reservation, has expanded since its startup authorization in 2000 to accommodate DOE’s material consolidation mission. During the facility’s growth and expansion, KAMS will have expanded its authorization capability of material types and storage containers to allow up to 8200 total shipping containers once the current expansion effort completes in 2014. Recognizing the need to safely and cost effectively manage other surplus material across the DOE Complex, KAC is constantly evaluating the storage of different material types within K area. When modifying storage areas in KAC, the Documented Safety Analysis (DSA) must undergo extensive calculations and reviews; however, without an extensive and proven security posture the possibility for expansion would not be possible. The KAC maintains the strictest adherence to safety and security requirements for all the SNM it handles. Disciplined Conduct of Operations and Conduct of Projects are demonstrated throughout this historical overview highlighting various improvements in capability, capacity, demonstrated cost effectiveness and utilization of the KAC as the DOE Center of Excellence for safe and secure storage of surplus SNM.

  7. Tank 12H Acidic Chemical Cleaning Sample Analysis And Material Balance

    SciTech Connect (OSTI)

    Martino, C. J.; Reboul, S. H.; Wiersma, B. J.; Coleman, C. J.

    2013-11-08T23:59:59.000Z

    A process of Bulk Oxalic Acid (BOA) chemical cleaning was performed for Tank 12H during June and July of 2013 to remove all or a portion of the approximately 4400 gallon sludge heel. Three strikes of oxalic acid (nominally 4 wt % or 2 wt %) were used at 55 ?C and tank volumes of 96- to 140-thousand gallons. This report details the sample analysis of a scrape sample taken prior to BOA cleaning and dip samples taken during BOA cleaning. It also documents a rudimentary material balance for the Tank 12H cleaning results.

  8. Role of minerals in formation of hydrocarbons during pyrolysis of organic matter - a material balance approach

    SciTech Connect (OSTI)

    Tannenbaum, E.; Huizinga, B.J.; Kaplan, I.R.

    1985-02-01T23:59:59.000Z

    Monterey Formation and Green River Formation kerogens (types II and I, respectively) were isolated, mixed with common sedimentary minerals, and pyrolyzed under dry and hydrous conditions for various times and temperatures. Analysis of all the pyrolyses products were conducted to perform a material balance and to infer reaction kinetics and mechanisms. Material balance of the pyrolyses products, in the presence and absence of minerals, reveals that the kerogen degradation results in the formation of bitumen rich in high molecular weight compounds in the initial stages, followed by additional cracking of kerogen and bitumen. However, amount and type of hydrocarbons in the pyrolyses products of kerogen in the presence of montmorillonite are markedly different from those produced by heating kerogen alone or with other minerals. The initial amounts of products in the presence of montmorillonite, and in particular the quantities of low molecular weight hydrocarbons, are higher than those in the presence of illite, calcite, and kerogen alone. The composition of these low molecular weight compounds is dominated by branched hydrocarbons, indicating catalytic cracking via carbonium ion mechanism, which is initiated on acidic sites of the clay. Composition differences are evident also in the distribution of n-alkanes and in the pristane/phytane ratio. The catalytic effect of montmorillonite, however, disappears in the presence of excess water. These differences may have important implications for the composition and quantities of petroleum generated from source rocks with different mineralogies.

  9. Analysis of Sub-Hourly Ramping Impacts of Wind Energy and Balancing Area Size: Preprint

    SciTech Connect (OSTI)

    Milligan, M.; Kirby, B.

    2008-06-01T23:59:59.000Z

    In this paper, we analyze sub-hourly ramping requirements and the benefit of combining Balancing Authority operations with significant wind penetrations.

  10. Unsteady-state material balance model for a continuous rotary dissolver

    SciTech Connect (OSTI)

    Lewis, B.E.

    1984-09-01T23:59:59.000Z

    The unsteady-state continuous rotary dissolver material balance code (USSCRD) is a useful tool with which to study the performance of the rotary dissolver under a wide variety of operating conditions. The code does stepwise continuous material balance calculations around each dissolver stage and the digester tanks. Output from the code consists of plots and tabular information on the stagewise concentration profiles of UO{sub 2}, PuO{sub 2}, fission products, Pu(NO{sub 3}){sub 4}, UO{sub 2}(NO{sub 3}){sub 2}, fission product nitrates, HNO{sub 3}, H{sub 2}O, stainless steel, total particulate, and total fuel in pins. Other information about material transfers, stagewise liquid volume, material inventory, and dissolution performance is also provided. This report describes the development of the code, its limitations, key operating parameters, usage procedures, and the results of the analysis of several sets of operating conditions. Of primary importance in this work was the estimation of the steady-state heavy metal inventory in a 0.5-t/d dissolver drum. Values ranging from {similar_to}12 to >150 kg of U + Pu were obtained for a variety of operating conditions. Realistically, inventories are expected to be near the lower end of this range. Study of the variation of operating parameters showed significant effects on dissolver product composition from intermittent solids feed. Other observations indicated that the cycle times for the digesters and shear feed should be closely coupled in order to avoid potential problems with off-specification product. 19 references, 14 tables.

  11. Laboratory to demolish excavation enclosures at Material Disposal Area B

    E-Print Network [OSTI]

    to hazardous and radiological contamination while excavating and packaging contaminated debris and soil from of a highly successful environmental cleanup project at Material Disposal Area B," said Ed Worth, federal project manager #12;- 2 - with the National Nuclear Security Administration's Los Alamos Site Office. "We

  12. Working with Radioactive Materials in Clinical Areas -Documentation

    E-Print Network [OSTI]

    Jia, Songtao

    Working with Radioactive Materials in Clinical Areas - Documentation Procedure: 7.54 Created: 2008 ­ Documentation A. Purpose This SOP summarizes records that must be maintained as required by the Rules. Responsibility Authorized User, approved technologist or lab manager ­ maintain records of receipt, use, spill

  13. Nuclear Materials Focus Area Fiscal Year 2002 Mid Year Review

    SciTech Connect (OSTI)

    Thiel, Elizabeth Chilcote

    2002-05-01T23:59:59.000Z

    The Nuclear Materials Focus Area (NMFA) held its annual mid-year review on February 12 and 14, 2002, in Santa Fe, New Mexico. The purpose of this review was to examine both the technical aspects and the programmatic aspects of its technology development program. The focus area activities were reviewed by a panel consisting of personnel representing the end users of the technologies, and technical experts in nuclear materials. This year's review was somewhat different than in the past, as the stress was on how well the various projects being managed through the NMFA aligned with the two thrust areas and nine key goals and priorities recently issued by the Deputy Assistant Secretary for DOE's Office of Environmental Management (EM).

  14. Nuclear Materials Focus Area Fiscal Year 2002 Mid Year Review

    SciTech Connect (OSTI)

    Thiel, E.C.; Fuhrman, P.W.

    2002-05-30T23:59:59.000Z

    The Nuclear Materials Focus Area (NMFA) held its annual mid-year review on February 12 and 14, 2002, in Santa Fe, New Mexico. The purpose of this review was to examine both the technical aspects and the programmatic aspects of its technology development program. The focus area activities were reviewed by a panel consisting of personnel representing the end users of the technologies, and technical experts in nuclear materials. This year's review was somewhat different than in the past, as the stress was on how well the various projects being managed through the NMFA aligned with the two thrust areas and nine key goals and priorities recently issued by the Deputy Assistant Secretary for DOE's Office of Environmental Management (EM).

  15. Role of minerals in thermal alteration of organic matter. II. A material balance

    SciTech Connect (OSTI)

    Tannenbaum, E.; Huizinga, B.J.; Kaplan, I.R.

    1986-09-01T23:59:59.000Z

    Pyrolysis experiments were performed on Green River and Monterey Formation kerogens (Types I and II, respectively) with and without calcite, illite, or montmorillonite at 300/sup 0/C for 2 to 1000 hours under dry and hydrous conditions. Pyrolysis products were identified and quantified, and a material balance of product and reactants resulted. Applying the results to maturation of organic matter in natural environments, they suggest that a given type of organic matter associated with different minerals in source rocks will yield different products. Furthermore, the different adsorption capacities of minerals exert a significant influence on the migration of polar and high molecular weight compounds generated from the breakdown of kerogen. Therefore, the overall accumulated products from carbonate source rocks are mainly heavy oils with some gas, whereas light oils and gases are the main products from source rocks that contain expandable clays with catalytic and adsorptive properties. 8 figures, 2 tables.

  16. Potential Reductions in Variability with Alternative Approaches to Balancing Area Cooperation with High Penetrations of Variable Generation

    SciTech Connect (OSTI)

    Milligan, M.; Kirby, B.; Beuning, S.

    2010-08-01T23:59:59.000Z

    The work described in this report was performed by the National Renewable Energy Laboratory (NREL) and funded by the Office of the Energy Efficiency and Renewable Energy, U.S. Department of Energy (EERE DOE). This project is a joint project with the Pacific Northwest National Laboratory. This report evaluates the physical characteristics that improve the ability of the power system to absorb variable generation. It then uses evidence from electricity markets in the Eastern Interconnection of the United States to show how large, fast energy markets can help with integration. The concept of Virtual Balancing Area is introduced, a concept that covers a broad range of cooperative measures that can be undertaken by balancing areas to help manage variability.

  17. Method for producing high surface area chromia materials for catalysis

    SciTech Connect (OSTI)

    Gash, Alexander E. (Brentwood, CA); Satcher, Joe (Patterson, CA); Tillotson, Thomas (Tracy, CA); Hrubesh, Lawrence (Pleasanton, CA); Simpson, Randall (Livermore, CA)

    2007-05-01T23:59:59.000Z

    Nanostructured chromium(III)-oxide-based materials using sol-gel processing and a synthetic route for producing such materials are disclosed herein. Monolithic aerogels and xerogels having surface areas between 150 m.sup.2/g and 520 m.sup.2/g have been produced. The synthetic method employs the use of stable and inexpensive hydrated-chromium(III) inorganic salts and common solvents such as water, ethanol, methanol, 1-propanol, t-butanol, 2-ethoxy ethanol, and ethylene glycol, DMSO, and dimethyl formamide. The synthesis involves the dissolution of the metal salt in a solvent followed by an addition of a proton scavenger, such as an epoxide, which induces gel formation in a timely manner. Both critical point (supercritical extraction) and atmospheric (low temperature evaporation) drying may be employed to produce monolithic aerogels and xerogels, respectively.

  18. An overview of the Nuclear Materials Focus Area research program

    SciTech Connect (OSTI)

    ROBERSON,GARY D.; POLANSKY,GARY F.; OSBORNE,KEN K.; RANDALL,VIRGINIA

    2000-02-25T23:59:59.000Z

    The Nuclear Material Focus Area (NMFA) is responsible for providing comprehensive needs identification, integration of technology research and development activities, and technology deployment for stabilization, packaging, and interim storage of surplus nuclear materials within the DOE complex. The NMFA was chartered in April 1999 by the Office of Science and Technology (OST), an organizational component of the US Department of Energy's (DOE) Office of Environmental Management (EM). OST manages a national program to conduct basic and applied research, and technology development, demonstration, and deployment assistance that is essential to completing a timely and cost-effective cleanup of the DOE nuclear weapons complex. DOE/EM provides environmental research results, as well as cleanup technologies and systems, to meet high-priority end-user needs, reduce EM's major cost centers and technological risks, and accelerate technology deployments. The NMFA represents the segment of EM that focuses on technological solutions for re-using, transforming, and disposing excess nuclear materials and is jointly managed by the DOE Albuquerque Operations Office and the DOE Idaho Operations Office.

  19. Analysis of the Impact of Balancing Area Cooperation on the Operation of the Western Interconnection with Wind and Solar Generation (Presentation)

    SciTech Connect (OSTI)

    Milligan, M.; Lew, D.; Jordan, G.; Piwko, R.; Kirby, B.; King, J.; Beuning, S.

    2011-05-01T23:59:59.000Z

    This presentation describes the analysis of the impact of balancing area cooperation on the operation of the Western Interconnection with wind and solar generation, including a discussion of operating reserves, ramping, production simulation, and conclusions.

  20. Balancing Area Coordination: Efficiently Integrating Renewable Energy Into the Grid, Greening the Grid (Brochure), NREL (National Renewable Energy Laboratory)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office511041cloth DocumentationProductsAlternativeOperationalAugustDecade5-F,INITIAL JohnE P T0BALANCING AREA

  1. A study of offshore benthic communities in natural areas and in areas affected by dredging and dredged material disposal

    E-Print Network [OSTI]

    Henry, Clyde Allan

    1976-01-01T23:59:59.000Z

    A STUDY QF OFFSHORE BENTHIC COMMUNITIES IN NATURAL AREAS AND IN AREAS AFFECTED BY DREDGING AND DREDGED MATERIAL DISPOSAL A Thesis by CLYDE ALLAN HENRY e Submitted to the Graduate College of Texas A&M University in partial fulfillment... of the requirement for the degree of MASTER OF SCIENCE August 1976 Major Subject: Biology A STCDY OF 0-FSHOBE BENTHIC COMKTNITIES IN NATURAL AREAS AND IN AREAS AFFECTED BY DREDGING AND DREDCFD NATERIAL DISPOSAL A Thesis by CLYDE ALLAN HENRY Approved...

  2. Case Study of Undrained Strength Stability Analysis for Dredged Material Placement Areas

    E-Print Network [OSTI]

    Case Study of Undrained Strength Stability Analysis for Dredged Material Placement Areas Timothy D perimeter dike at the Craney Island Dredged Material Management Area CIDMMA using an undrained strength of the effective overburden stress of the dredged material and the marine clay underlying the dike. An undrained

  3. Approach to IAEA material-balance verification with intermittent inspection at the Portsmouth Gas Centrifuge Enrichment Plant

    SciTech Connect (OSTI)

    Gordon, D.M.; Sanborn, J.B.

    1984-05-18T23:59:59.000Z

    This paper describes a potential approach by which the International Atomic Energy Agency (IAEA) might verify the nuclear-material balance at the Portsmouth Gas Centrifuge Enrichment Plant (GCEP) for the circumstance in which the IAEA inspections occur on an intermittent basis. The verification approach is a variation of the standard IAEA attributes/variables measurement-verification method. This alternative approach is useful and applicable at the Portsmouth GCEP, which will ship all its product and tails UF/sub 6/ to United States facilities not eligible for IAEA safeguards. The paper reviews some of the relevant results of the Hexapartite Safeguards Project (HSP), describes the standard IAEA material-balance-verification approach for bulk-handling facilities, and provides the procedures to be followed in handling and processing UF/sub 6/ cylinders at the Portsmouth GCEP. The paper then discusses the assumptions made in the approach, and derives a formula for the probability with which the IAEA could detect the diversion of a significant quantity of uranium (75 kg of U-235 in depleted, normal, and low-enriched uranium) if this method were applied. The paper also provides numerical examples of IAEA detection probability should the operator divert uranium from the feed, product, or tails streams for the Portsmouth GCEP with a capacity of 1100 tonnes of separative work per year.

  4. Estimating material and energy intensities of urban areas

    E-Print Network [OSTI]

    Quinn, David James, Ph. D. Massachusetts Institute of Technology

    2012-01-01T23:59:59.000Z

    The objective of this thesis is to develop methods to estimate, analyze and visualize the resource intensity of urban areas. Understanding the resource consumption of the built environment is particularly relevant in cities ...

  5. Approach to IAEA verification of the nuclear-material balance at the Portsmouth Gas Centrifuge Enrichment Plant (GCEP)

    SciTech Connect (OSTI)

    Gordon, D.M.; Sanborn, J.B.; Younkin, J.M.; DeVito, V.J.

    1982-01-01T23:59:59.000Z

    This paper describes a potential approach by which the International Atomic Energy Agency (IAEA) might verify the nuclear-material balance at the Portsmouth Gas Centrifuge Enrichment Plant (GCEP), should that plant be placed under IAEA safeguards. The strategy makes use of the attributes and variables measurement verification approach, whereby the IAEA would perform independent measurements on a randomly selected subset of the items comprising the U-235 flows and inventories at the plant. In addition, the MUF-D statistic is used as the test statistics for the detection of diversion. The paper includes descriptions of the potential verification activities, as well as calculations of (a) attributes and variables sample sizes for the various strata, (b) standard deviations of the relevant test statistics, and (c) the sensitivity for detection of diversion which the IAEA might achieve by this verification strategy at GCEP.

  6. Carbon-Based Materials, High-Surface-Area Sorbents, and New Materials and Concepts

    Broader source: Energy.gov [DOE]

    This category of materials-based storage technologies includes a range of carbon-based materials such as carbon nanotubes, aerogels, nanofibers (including metal-doped hybrids), as well as metal...

  7. The Nuclear Material Focus Area Roadmapping Process Utilizing Environmental Management Complex-Wide Nuclear Material Disposition Pathways

    SciTech Connect (OSTI)

    Sala, D. R.; Furhman, P.; Smith, J. D.

    2002-02-26T23:59:59.000Z

    This paper describes the process that the Nuclear Materials Focus Area (NMFA) has developed and utilizes in working with individual Department of Energy (DOE) sites to identify, address, and prioritize research and development efforts in the stabilization, disposition, and storage of nuclear materials. By associating site technology needs with nuclear disposition pathways and integrating those with site schedules, the NMFA is developing a complex wide roadmap for nuclear material technology development. This approach will leverage technology needs and opportunities at multiple sites and assist the NMFA in building a defensible research and development program to address the nuclear material technology needs across the complex.

  8. Large-area chromogenics: Materials and devices for transmittance control. Volume IS 4

    SciTech Connect (OSTI)

    Lampert, C.M. [ed.] [Lawrence Berkeley Lab., CA (United States); Granqvist, C.G. [ed.] [Chalmers Univ. of Technology and Univ. of Gothenburg, Gothenburg (Sweden)

    1990-12-31T23:59:59.000Z

    Chromogenic materials can alter their optical properties in a persistent yet reversible manner when subjected to a change in external conditions such as irradiation intensity, temperature, or electric-field strength. In the future chromogenic materials may be used on large scale to regulate the throughput of radiant energy for windows in buildings and cars, so that comfortable lighting and temperature are maintained without excessive air conditioning. The purpose of this book is to give a broad coverage of large-area chromogenics and to discuss their applications. The book is divided into the following areas: applications; photochromic materials; thermochromic materials; inorganic electrochromic materials; inorganic electrochromic materials; organic electrochromic materials; conductors for ions and electrons in electrochromic devices; electrochromic devices; and liquid crystals materials and devices. Separate abstracts were prepared for 33 papers in this book.

  9. Carbon-Based Materials, High-Surface-Area Sorbents, and New Materials...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    technologies includes a range of carbon-based materials such as carbon nanotubes, aerogels, nanofibers (including metal-doped hybrids), as well as metal-organic frameworks,...

  10. A Program to Stabilize Nuclear Materials as Managed by the Plutonium Focus Area

    SciTech Connect (OSTI)

    B. Kenley (Kenley Consulting); B. Scott; B. Seidel (ANL-W); D. Knecht (LMITCO); F. Southworth; K. Osborne (DOE-ID); N. Chipman; T. Creque

    1999-03-01T23:59:59.000Z

    This paper describes the program to stabilize nuclear materials, consistent with the Department of Energy Office of Environmental Management (EM) plan, Accelerating Cleanup: Paths to Closure. The program is managed by the Plutonium Stabilization and Disposition Focus Area, which defines and manages technology development programs to stabilize nuclear materials and assure their subsequent safe storage and final disposition. The scope of the Plutonium Stabilization and Disposition Focus Area (PFA) activities includes non-weapons plutonium materials, special isotopes, and other fissile materials. The PFA provides solutions to site-specific and complex wide technology issues associated with plutonium remediation, stabilization, and preparation for disposition. Our paper describes an important programmatic function of the Department of Energy nuclear materials stabilization program, including the tie-in of policy to research needs and funding for the nuclear materials disposition area. The PFA uses a rigorous systems engineering determination of technology needs and gaps, under the guidance of a Technical Advisory Panel, consisting of complex-wide experts. The Research and Development planning provides an example for other waste areas and should be of interest to Research and Development managers. The materials disposition maps developed by the PFA and described in this paper provide an evaluation of research needs, data gaps and subsequent guidance for the development of technologies for nuclear materials disposition. This paper also addresses the PFA prioritization methodology and its ability to forecast actual time to implementation.

  11. SEVERE WEATHER EXPLOSION HAZARDOUS MATERIALS Alert people in the immediate area to

    E-Print Network [OSTI]

    Karonis, Nicholas T.

    SEVERE WEATHER EXPLOSION HAZARDOUS MATERIALS EVACUATE · Alert people in the immediate area producing devices · Do not try to locate the source of the explosion · Evacuate and move to designated as OUTAGE EVALUATE · Remain calm and move cautiously to a lighted area · If the fire alarm sounds or upon

  12. Self assembled molecular monolayers on high surface area materials as molecular getters

    DOE Patents [OSTI]

    King, D.E.; Herdt, G.C.; Czanderna, A.W.

    1997-01-07T23:59:59.000Z

    The present invention relates to a gettering material that may be used as a filtration medium to remove pollutants from the environment. The gettering material comprises a high surface area material having a metal surface that chemically bonds n-alkanethiols in an organized manner thereby forming a molecular monolayer over the metal surface. The n-alkanethiols have a free functional group that interacts with the environment thereby binding specific pollutants that may be present. The gettering material may be exposed to streams of air in heating, ventilation, and air conditioning systems or streams of water to remove specific pollutants from either medium. 9 figs.

  13. Self assembled molecular monolayers on high surface area materials as molecular getters

    DOE Patents [OSTI]

    King, David E. (Lakewood, CO); Herdt, Gregory C. (Denver, CO); Czanderna, Alvin W. (Denver, CO)

    1997-01-01T23:59:59.000Z

    The present invention relates to a gettering material that may be used as a filtration medium to remove pollutants from the environment. The gettering material comprises a high surface area material having a metal surface that chemically bonds n-alkanethiols in an organized manner thereby forming a molecular monolayer over the metal surface. The n-alkanethiols have a free functional group that interacts with the environment thereby binding specific pollutants that may be present. The gettering material may be exposed to streams of air in heating, ventilation, and air conditioning systems or streams of water to remove specific pollutants from either medium.

  14. MATERIAL BALANCE REPORT

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetterEconomy andTermsDepartment1| Department ofEnergyF 742

  15. Settlement of Dredged and Contaminated Material Placement Areas. II: Primary Consolidation, Secondary Compression,

    E-Print Network [OSTI]

    Settlement of Dredged and Contaminated Material Placement Areas. II: Primary Consolidation, Secondary Compression, and Desiccation of Dredged Fill Input Parameters Timothy D. Stark 1; Hangseok Choi2, Secondary Compression, and Desiccation of Dredged Fill), which is described in a companion paper

  16. Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama. Annual report, March 1996--March 1997

    SciTech Connect (OSTI)

    Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.; Alabi, G.G.; Groshong, R.H.

    1997-08-01T23:59:59.000Z

    Gilbertown Field is the oldest oil field in Alabama and produces oil from chalk of the Upper Cretaceous Selma Group and from sandstone of the Eutaw Formation along the southern margin of the Gilbertown fault system. Most of the field has been in primary recovery since establishment, but production has declined to marginally economic levels. This investigation applies advanced geologic concepts designed to aid implementation of improved recovery programs. The Gilbertown fault system is detached at the base of Jurassic salt. The fault system began forming as a half graben and evolved in to a full graben by the Late Cretaceous. Conventional trapping mechanisms are effective in Eutaw sandstone, whereas oil in Selma chalk is trapped in faults and fault-related fractures. Burial modeling establishes that the subsidence history of the Gilbertown area is typical of extensional basins and includes a major component of sediment loading and compaction. Surface mapping and fracture analysis indicate that faults offset strata as young as Miocene and that joints may be related to regional uplift postdating fault movement. Preliminary balanced structural models of the Gilbertown fault system indicate that synsedimentary growth factors need to be incorporated into the basic equations of area balance to model strain and predict fractures in Selma and Eutaw reservoirs.

  17. Wide-Area Energy Storage and Management system to Balance Intermittent Resources in the Bonneville Power Administration and California ISO Control Areas

    SciTech Connect (OSTI)

    Makarov, Yuri V.; Yang, Bo; DeSteese, John G.; Lu, Shuai; Miller, Carl H.; Nyeng, Preben; Ma, Jian; Hammerstrom, Donald J.; Vishwanathan, Vilanyur V.

    2008-06-30T23:59:59.000Z

    The entire project addresses the issue of mitigating additional intermittency and fast ramps that occur at higher penetration of intermittent resources, including wind genera-tion, in the Bonneville Power Administration (BPA) and the California Independent Sys-tem Operator (California ISO) control areas. The proposed Wide Area Energy Storage and Management System (WAEMS) will address the additional regulation requirement through the energy exchange between the participating control areas and through the use of energy storage and other generation resources. For the BPA and California ISO control centers, the new regulation service will look no different comparing with the traditional regulation resources. The proposed project will benefit the regulation service in these service areas, regardless of the actual degree of penetration of the intermittent resources in the regions. The project develops principles, algorithms, market integration rules, functional de-sign and technical specifications for the WAEMS system. The project is sponsored by BPA and supported in kind by California ISO, Beacon Power Corporation, and the Cali-fornia Energy Commission (CEC).

  18. Evaluation of dredged material proposed for ocean disposal from Arthur Kill Project Area, New York

    SciTech Connect (OSTI)

    Gruendell, B.D.; Barrows, E.S.; Borde, A.B. [Battelle Marine Sciences Lab., Sequim, WA (United States)

    1997-01-01T23:59:59.000Z

    The objective of the bioassay reevaluation of Arthur Kill Federal Project was to reperform toxicity testing on proposed dredged material following current ammonia reduction protocols. Arthur Kill was one of four waterways sampled and evaluated for dredging and disposal in April 1993. Sediment samples were recollected from the Arthur Kill Project areas in August 1995. Tests and analyses were conducted according to the manual developed by the USACE and the U.S. Environmental Protection Agency (EPA), Evaluation of Dredged Material Proposed for Ocean Disposal (Testing Manual), commonly referred to as the {open_quotes}Green Book,{close_quotes} and the regional manual developed by the USACE-NYD and EPA Region II, Guidance for Performing Tests on Dredged Material to be Disposed of in Ocean Waters. The reevaluation of proposed dredged material from the Arthur Kill project areas consisted of benthic acute toxicity tests. Thirty-three individual sediment core samples were collected from the Arthur Kill project area. Three composite sediments, representing each reach of the area proposed for dredging, was used in benthic acute toxicity testing. Benthic acute toxicity tests were performed with the amphipod Ampelisca abdita and the mysid Mysidopsis bahia. The amphipod and mysid benthic toxicity test procedures followed EPA guidance for reduction of total ammonia concentrations in test systems prior to test initiation. Statistically significant acute toxicity was found in all Arthur Kill composites in the static renewal tests with A. abdita, but not in the static tests with M. bahia. Statistically significant acute toxicity and a greater than 20% increase in mortality over the reference sediment was found in the static renewal tests with A. abdita. M. bahia did not show statistically significant acute toxicity or a greater than 10% increase in mortality over reference sediment in static tests. 5 refs., 2 figs., 2 tabs.

  19. Evaluation of dredged material proposed for ocean disposal from Hackensack River Project Area, New York

    SciTech Connect (OSTI)

    Gruendell, B.D.; Barrows, E.S.; Borde, A.B. [Battelle Marine Sciences Lab., Sequim, WA (United States)

    1997-01-01T23:59:59.000Z

    The objective of the bioassay reevaluation of the Hackensack River Federal Project was to reperform toxicity testing on proposed dredged material with current ammonia reduction protocols. Hackensack River was one of four waterways sampled and evaluated for dredging and disposal in April 1993. Sediment samples were re-collected from the Hackensack River Project area in August 1995. Tests and analyses were conducted according to the manual developed by the USACE and the U.S. Environmental Protection Agency (EPA), Evaluation of Dredged Material Proposed for Ocean Disposal (Testing Manual), commonly referred to as the {open_quotes}Green Book,{close_quotes} and the regional manual developed by the USACE-NYD and EPA Region II, Guidance for Performing Tests on Dredged Material to be Disposed of in Ocean Waters. The reevaluation of proposed dredged material from the Hackensack River project area consisted of benthic acute toxicity tests. Thirty-three individual sediment core samples were collected from the Hackensack River project area. Three composite sediments, representing each reach of the area proposed for dredging, were used in benthic acute toxicity testing. Benthic acute toxicity tests were performed with the amphipod Ampelisca abdita and the mysid Mysidopsis bahia. The amphipod and mysid benthic toxicity test procedures followed EPA guidance for reduction of total ammonia concentrations in test systems prior to test initiation. Statistically significant acute toxicity was found in all three Hackensack River composites in the static renewal tests with A. abdita, but not in the static tests with M. bahia. Statistically significant acute toxicity and a greater than 20% increase in mortality over the reference sediment was found in the static renewal tests with A. abdita. Statistically significant mortality 10% over reference sediment was observed in the M. bahia static tests. 5 refs., 2 figs., 2 tabs.

  20. Evaluation of dredged material proposed for ocean disposal from Westchester Creek project area, New York

    SciTech Connect (OSTI)

    Pinza, M.R.; Gardiner, W.W.; Barrows, E.S.; Borde, A.B.

    1996-11-01T23:59:59.000Z

    The objective of the Westchester Creek project was to evaluate proposed dredged material from this area to determine its suitability for unconfined ocean disposal at the Mud Dump Site. Westchester Creek was one of five waterways that the US Army Corps of Engineers- New York District (USACE-NYD) requested the Battelle/Marine Sciences Laboratory (MSL) to sample and evaluate for dredging and disposal in May 1995. The evaluation of proposed dredged material from the Westchester Creek project area consisted of bulk sediment chemical analyses, chemical analyses of dredging site water and elutriate, benthic acute and water-column toxicity tests, and bioaccumulation studies. Thirteen individual sediment core samples were collected from this area and analyzed for grain size, moisture content, and total organic carbon (TOC). One composite sediment sample representing the Westchester Creek area to be dredged, was analyzed for bulk density, specific gravity, metals, chlorinated pesticides, polychlorinated biphenyl (PCB) congeners, polynuclear aromatic hydrocarbons (PAHs), and 1,4-dichlorobenzene. Dredging site water and elutriate water, which is prepared from the suspended- particulate phase (SPP) of the Westchester Creek sediment composite, was analyzed for metals, pesticides, and PCBS.

  1. Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama. Final report, March 1996--September 1998

    SciTech Connect (OSTI)

    Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.; Alabi, G.G.; Carroll, R.E.; Groshong, R.H.; Jin, G.

    1998-12-01T23:59:59.000Z

    This project was designed to analyze the structure of Mesozoic and Tertiary strata in Gilbertown Field and adjacent areas to suggest ways in which oil recovery can be improved. The Eutaw Formation comprises 7 major flow units and is dominated by low-resistivity, low-contrast play that is difficult to characterize quantitatively. Selma chalk produces strictly from fault-related fractures that were mineralized as warm fluid migrated from deep sources. Resistivity, dipmeter, and fracture identification logs corroborate that deformation is concentrated in the hanging-wall drag zones. New area balancing techniques were developed to characterize growth strata and confirm that strain is concentrated in hanging-wall drag zones. Curvature analysis indicates that the faults contain numerous fault bends that influence fracture distribution. Eutaw oil is produced strictly from footwall uplifts, whereas Selma oil is produced from fault-related fractures. Clay smear and mineralization may be significant trapping mechanisms in the Eutaw Formation. The critical seal for Selma reservoirs, by contrast, is where Tertiary clay in the hanging wall is juxtaposed with poorly fractured Selma chalk in the footwall. Gilbertown Field can be revitalized by infill drilling and recompletion of existing wells. Directional drilling may be a viable technique for recovering untapped oil from Selma chalk. Revitalization is now underway, and the first new production wells since 1985 are being drilled in the western part of the field.

  2. Enabling completion of the material disposition area G closure at the Los Alamos National Laboratory

    SciTech Connect (OSTI)

    Blankenhorn, James Allen [Los Alamos National Laboratory; Bishop, Milton L [Los Alamos National Laboratory

    2010-01-01T23:59:59.000Z

    Los Alamos National Security, LLC (LANS) and the Los Alamos Site Office (LASO) have developed and are implementing an integrated strategy to accelerate the disposition of Los Alamos National Laboratory (LANL) legacy transuranic waste inventory currently stored in Technical Area 54, Material Disposition Area (MDA) G. As that strategy has been implemented the easier waste streams have been certified and shipped leaving the harder more challenging wastes to be dispositioned. Lessons learned from around the complex and a partnership with the National Transuranic Program located in Carlsbad, New Mexico, are enabling this acceleration. The Waste Disposition Program is responsible for the removal of both the above ground and below grade, retrievably stored transuranic waste in time to support the negotiated consent order with the State of New Mexico which requires closure of MDA G by the year 2015. The solutions and strategy employed at LANL are applicable to any organization that is currently managing legacy transuranic waste.

  3. Evaluation of dredged material proposed for ocean disposal from Eastchester Project Area, New York

    SciTech Connect (OSTI)

    Antrim, L.D.; Pinza, M.R.; Barrows, E.S.; Gardiner, W.W.; Tokos, J.J.S.; Gruendell, B.D.; Word, J.Q. [Battelle Marine Research Lab., Sequim, WA (United States)

    1996-07-01T23:59:59.000Z

    The objective of the Eastchester project (Federal Project [FP] No. 6) was to evaluate proposed dredged material from the Eastchester project area in the Hutchinson River to determine its suitability for unconfined ocean disposal at the Mud Dump Site. Eastchester was one of seven waterways that the U. S. Army Corps of Engineers-New York District (USACE-NYD) requested the Battelle/Marine Sciences Laboratory (MSL) to sample and evaluate for dredging and disposal in March 1994. The evaluation of proposed dredged material from the Eastchester project area consisted of bulk sediment chemical analyses, chemical analyses of dredging site water and elutriate, water- column and benthic acute toxicity tests, and bioaccumulation studies. Eighteen individual sediment core samples collected from the Eastchester project area were analyzed for grain size, moisture content, and total organic carbon (TOC). Two composite sediment samples, representing the upstream and lower reaches of the area proposed for dredging, were analyzed for bulk density, specific gravity, metals, chlorinated pesticides, polychlorinated biphenyl (PCB) congeners, polynuclear aromatic hydrocarbons (PAHs), and 1,4- dichlorobenzene. Dredging site water and elutriate water, which is prepared from the suspended-particulate phase (SPP) of the two Eastchester sediment composites, were analyzed for metals, pesticides, and PCBS. An additional 1 1 composite samples were created for the USACE-New England Division (USACE-NED) using the same 18 Eastchester core samples but combined into different composites. These composites were analyzed for metals, chlorinated pesticides, PCB congeners, PAHS, and 1,4-dichlorobenzene. Water-column or SPP toxicity tests were performed along with bioaccumulation tests.

  4. Evaluation of dredged material proposed for ocean Disposal from Shoal Harbor/Compton Creek Project Area

    SciTech Connect (OSTI)

    Gardiner, W.W.; Borde, A.B.; Nieukirk, S.L.; Barrows, E.S.; Gruendell, B.D.; Word, J.Q.

    1996-10-01T23:59:59.000Z

    The objective of the Shoal Harbor/Compton Creek Project was to evaluate proposed dredged material from the Shoal harbor/Compton Creek Project Area in Belford and Monmouth, New Jersey to determine its suitability for unconfined ocean disposal at the Mud Dump Site. This was one of five waterways that the US Army Corps of Engineers- New York District requested the Battelle Marine Sciences Laboratory (MSL) to sample and evaluate for dredging and disposal in May 1995. The evaluation of proposed dredged material from the Shoal Harbor/Compton Creek Project area consisted of bulk chemical analyses, chemical analyses of dredging site water and elutriate, benthic and water-column acute toxicity tests and bioaccumulation studies. Eleven core samples were analyzed or grain size, moisture content, and total organic carbon. Other sediments were evaluated for bulk density, specific gravity, metals, chlorinated pesticides, polychlorinated biphenyl (PCB) congers, polynuclear aromatic hydrocarbons, and 1,4- dichlorobenzene. Dredging site water and elutriate water were analyzed for metals, pesticides, and PCBs.

  5. Evaluation of dredged material proposed for ocean disposal from Bronx River Project Area, New York

    SciTech Connect (OSTI)

    Gruendell, B.D.; Gardiner, W.W.; Antrim, L.D.; Pinza, M.R.; Barrows, E.S.; Borde, A.B. [Battelle Marine Research Lab., Sequim, WA (United States)

    1996-12-01T23:59:59.000Z

    The objective of the Bronx River project was to evaluate proposed dredged material from the Bronx River project area in Bronx, New York, to determine its suitability for unconfined ocean disposal at the Mud Dump Site. Bronx River was one of five waterways that the US Army Corps of Engineers-New York District (USAGE-NYD) requested the Battelle Marine Sciences Laboratory (MSL) to sample and to evaluate for dredging and disposal. Sediment samples were submitted for physical and chemical analyses, chemical analyses of dredging site water and elutriate, benthic and water-column acute toxicity tests, and bioaccumulation studies. Fifteen individual sediment core samples collected from the Bronx River project area were analyzed for grain size, moisture content, and total organic carbon (TOC). One composite sediment sample, representing the entire reach of the area proposed for dredging, was analyzed for bulk density, specific gravity, metals, chlorinated pesticides, polychlorinated biphenyl (PCB) congeners, polynuclear aromatic hydrocarbons (PAH), and 1,4- dichlorobenzene. Dredging site water and elutriate water, which was prepared from the suspended-particulate phase (SPP) of the Bronx River sediment composite, were analyzed for metals, pesticides, and PCBS.

  6. Balancing the Need to Develop Coastal Areas with the Desire for an Ecologically Functioning Coastal Environment: Is Net Ecosystem Improvement Possible?

    SciTech Connect (OSTI)

    Thom, Ronald M.; Williams, Greg D.; Diefenderfer, Heida L.

    2005-03-01T23:59:59.000Z

    The global human population is growing exponentially, a majority lives and works near the coast, and coastal commerce and development are critical to the economies of many nations. Hence, coastal areas will continue to be a major focus of development and economic activity. People want and need the economics provided by coastal development but they also want and need the fisheries and social commodities supported by estuarine and coastal ecosystems. Because of these facts, we view the challenge of balancing coastal development with enhancing nearshore marine and estuarine ecosystems (i.e., net ecosystem improvement) as the top priority for coastal researchers in this century. Our restoration research in Pacific Northwest estuaries and participation in the design and mitigation of nearshore structures has largely dealt with these competing goals. To this end, we have applied conceptual models, comprehensive assessment methods, and principles of restoration ecology, conservation biology and adaptive management to incorporate science into decisions about use of estuarine systems. Case studies of Bainbridge Island and the Columbia River demonstrate the use of objective, defensible methods to prioritize estuarine areas for preservation, conservation and restoration. Case studies of Clinton, WA and Port Townsend, WA demonstrate the incorporation of an ecological perspective and technological solutions into design projects that affect the nearshore. Adaptive management has allowed coastal development and restoration uncertainties to be better evaluated, with the information used to improve management decisions. Although unproven on a large scale, we think that these kinds of methods can contribute to the net improvement of already degraded ecosystems. The challenges include applied science to understand the issues, education, incentives, empirical data (not rehashing of reviews), cumulative impact analysis, and an effective adaptive management program. Because the option of net ecosystem improvement is often more costly than other alternatives, commitment by the local or regional community to this approach is essential.

  7. Magnitude and spatial distribution of urban flammable materials in the San Jose Area, California

    SciTech Connect (OSTI)

    Simonett, D.S.; Barrett, T.N.; Gopal, S.; Holsmuller, F.J.; G.Q. Sun

    1986-02-01T23:59:59.000Z

    The distribution and quantity of flammable materials in urban areas is of importance for any study of the fire spread and plume dynamics which may result from a nuclear attack. This study presents a methodology which uses aerial photographs and a 1000 feet sample grid to collect this information for San Jose and adjoining urban areas in California. A detailed literature search was carried out to develop estimates of the fuel loading of the major building types in an urban environment. Due to the ambiguities in this literature, the values as used here are approximations, but are supported by details of sources and assumptions. Some straightforward calculations using the results from the air photo interpretation and the literature search, yield information about the fire load and also urban characteristics per grid cell, including information on fire breaks which are important features with respect to fire spread. The results yield an average preliminary and partial fuel value of 9.2 kg/m/sup 2/. This value is less than fuel loads estimated in the literature using different methods of obtaining data and is certainly less than the actual fuel loading for San Jose. However, we doubt that with further work we will find the average San Jose value to be any higher than 13 kg/m/sup 2/. Additional sources of fuel which remain to be accounted for both in aggregate magnitude, and expected burnable fractions, include asphalt of roofs, streets, sidewalks, and parking lots, fuel storage facilities, fuel and natural gas in pipelines, natural vegetation, and external storage of lumber, construction, commercial and industrial-process materials.

  8. TEMPERATURE PREDICTION IN 3013 CONTAINERS IN K AREA MATERIAL STORAGE (KAMS) FACILITY USING REGRESSION METHODS

    SciTech Connect (OSTI)

    Gupta, N

    2008-04-22T23:59:59.000Z

    3013 containers are designed in accordance with the DOE-STD-3013-2004. These containers are qualified to store plutonium (Pu) bearing materials such as PuO2 for 50 years. DOT shipping packages such as the 9975 are used to store the 3013 containers in the K-Area Material Storage (KAMS) facility at Savannah River Site (SRS). DOE-STD-3013-2004 requires that a comprehensive surveillance program be set up to ensure that the 3013 container design parameters are not violated during the long term storage. To ensure structural integrity of the 3013 containers, thermal analyses using finite element models were performed to predict the contents and component temperatures for different but well defined parameters such as storage ambient temperature, PuO{sub 2} density, fill heights, weights, and thermal loading. Interpolation is normally used to calculate temperatures if the actual parameter values are different from the analyzed values. A statistical analysis technique using regression methods is proposed to develop simple polynomial relations to predict temperatures for the actual parameter values found in the containers. The analysis shows that regression analysis is a powerful tool to develop simple relations to assess component temperatures.

  9. IEEE TRANSACTIONS ON COMPUTER-AIDED DESIGN OF INTEGRATED CIRCUITS AND SYSTEMS, VOL. 20, NO. 5, MAY 2001 583 Critical Area Computation for Missing Material

    E-Print Network [OSTI]

    Papadopoulou, Evanthia

    2001 583 Critical Area Computation for Missing Material Defects in VLSI Circuits Evanthia Papadopoulou Abstract--We address the problem of computing critical area for missing material defects in a circuit for rectilinear layouts. Index Terms--Breaks, critical area, missing material defects, opens, via blocks, Voronoi

  10. Large-Area Quality Control of Atomically-Thin Layered Materials

    E-Print Network [OSTI]

    Nolen, Craig Merten

    2012-01-01T23:59:59.000Z

    and K. S. Novoselov, Nature Materials 6, 183 (2007) 8. R. E.R) (2007). Chapter 3 Material Layer Identification Techniqueto Charge Density Wave Materials,” MRS Proceed. , Vol. 1344,

  11. MATERIAL BALANCES AND APPLICATIONS MATERIAL BALANCES AND APPLICATIONS

    E-Print Network [OSTI]

    Al-Juhani, Abdulhadi A.

    Equation Suppose propane is a component of both the input and output streams of a continuous process unit propane/h) qout (kg propane/h) If there are no leaks and the measurements are correct, then the other possibilities that can account for this difference are that propane is either being generated, consumed

  12. Environmental effects of dredging. Interim guidance for predicting quality of effluent discharged from confined dredged material disposal areas--data analysis. Technical note

    SciTech Connect (OSTI)

    Palermo, M.R.; Engler, R.M.

    1985-06-01T23:59:59.000Z

    The following series of technical notes described the functions necessary for predicting the quality of effluent discharged from confined dredged material disposal areas during dredging operations.

  13. Cyclododecane as support material for clean and facile transfer of large-area few-layer graphene

    SciTech Connect (OSTI)

    Capasso, A.; Leoni, E.; Dikonimos, T.; Buonocore, F.; Lisi, N. [ENEA, Materials Technology Unit, Surface Technology Laboratory, Casaccia Research Centre, Via Anguillarese 301, 00060 Rome (Italy); De Francesco, M. [ENEA, Technical Unit for Renewable Energies Sources, Casaccia Research Center, Via Anguillarese 301, 00060 Rome (Italy); Lancellotti, L.; Bobeico, E. [ENEA, Portici Research Centre, P.le E. Fermi 1, 80055 Portici (Italy); Sarto, M. S.; Tamburrano, A.; De Bellis, G. [Research Center on Nanotechnology Applied to Engineering of Sapienza (CNIS), SSNLab, Sapienza University of Rome, P.le Aldo Moro 5, 00185 Rome (Italy)

    2014-09-15T23:59:59.000Z

    The transfer of chemical vapor deposited graphene is a crucial process, which can affect the quality of the transferred films and compromise their application in devices. Finding a robust and intrinsically clean material capable of easing the transfer of graphene without interfering with its properties remains a challenge. We here propose the use of an organic compound, cyclododecane, as a transfer material. This material can be easily spin coated on graphene and assist the transfer, leaving no residues and requiring no further removal processes. The effectiveness of this transfer method for few-layer graphene on a large area was evaluated and confirmed by microscopy, Raman spectroscopy, x-ray photoemission spectroscopy, and four-point probe measurements. Schottky-barrier solar cells with few-layer graphene were fabricated on silicon wafers by using the cyclododecane transfer method and outperformed reference cells made by standard methods.

  14. Evaluation of dredged material proposed for ocean disposal from Red Hook/Bay Ridge project areas, New York

    SciTech Connect (OSTI)

    Pinza, M.R.; Barrows, E.S.; Borde, A.B. [Battelle/Marine Sciences Lab., Sequim, WA (United States)

    1996-09-01T23:59:59.000Z

    The objective of the Red HookIBay Ridge project was to evaluate proposed dredged material from these two areas to determine its suitability for unconfined ocean disposal at the Mud Dump Site. Sediment samples were collected from the Red Hook/Bay Ridge project areas. Tests and analyses were conducted. The evaluation of proposed dredged material from the Red Hook/Bay Ridge project areas consisted of bulk sediment chemical analyses, chemical analyses of dredging site water and elutriate, water-column and benthic acute toxicity tests. Twenty-four individual sediment core samples were collected from these two areas and analyzed for grain size, moisture content, and total organic carbon (TOC). Three composite sediment samples, representing Red Hook Channel and the two Bay Ridge Reaches to be dredged, were analyzed for bulk density, specific gravity, metals, chlorinated pesticides, polychlorinated biphenyl (PCB) congeners, polynuclear aromatic hydrocarbons (PAH), and 1,4-dichlorobenzene. Dredging site water and elutriate water, which is prepared from the suspended-particulate phase (SPP) of the three Red Hook Bay Ridge sediment composites, were analyzed for metals, pesticides, and PCBS. Benthic acute toxicity tests were performed. Water-column or SPP toxicity tests were performed. Bioaccumulation tests were also conducted.

  15. E-Area Vault Concrete Material Property And Vault Durability/Degradation Projection Recommendations

    SciTech Connect (OSTI)

    Phifer, M. A.

    2014-03-11T23:59:59.000Z

    Subsequent to the 2008 E-Area Low-Level Waste Facility (ELLWF) Performance Assessment (PA) (WSRC 2008), two additional E-Area vault concrete property testing programs have been conducted (Dixon and Phifer 2010 and SIMCO 2011a) and two additional E-Area vault concrete durability modeling projections have been made (Langton 2009 and SIMCO 2012). All the information/data from these reports has been evaluated and consolidated herein by the Savannah River National Laboratory (SRNL) at the request of Solid Waste Management (SWM) to produce E-Area vault concrete hydraulic and physical property data and vault durability/degradation projection recommendations that are adequately justified for use within associated Special Analyses (SAs) and future PA updates. The Low Activity Waste (LAW) and Intermediate Level (IL) Vaults structural degradation predictions produced by Carey 2006 and Peregoy 2006, respectively, which were used as the basis for the 2008 ELLWF PA, remain valid based upon the results of the E-Area vault concrete durability simulations reported by Langton 2009 and those reported by SIMCO 2012. Therefore revised structural degradation predictions are not required so long as the mean thickness of the closure cap overlying the vaults is no greater than that assumed within Carey 2006 and Peregoy 2006. For the LAW Vault structural degradation prediction (Carey 2006), the mean thickness of the overlying closure cap was taken as nine feet. For the IL Vault structural degradation prediction (Peregoy 2006), the mean thickness of the overlying closure cap was taken as eight feet. The mean closure cap thicknesses as described here for both E-Area Vaults will be included as a key input and assumption (I&A) in the next revision to the closure plan for the ELLWF (Phifer et al. 2009). In addition, it has been identified as new input to the PA model to be assessed in the ongoing update to the new PA Information UDQE (Flach 2013). Once the UDQE is approved, the SWM Key I&A database will be updated with this new information.

  16. Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama -- Year 2. Annual report, March 1997--March 1998

    SciTech Connect (OSTI)

    Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.; Alabi, G.G.; Carroll, R.E.

    1998-09-01T23:59:59.000Z

    Gilbertown Field is the oldest oil field in Alabama and has produced oil from fractured chalk of the Cretaceous Selma Group and glauconitic sandstone of the Eutaw Formation. Nearly all of Gilbertown Field is still in primary recovery, although waterflooding has been attempted locally. The objective of this project is to analyze the geologic structure and burial history of Mesozoic and Tertiary strata in Gilbertown Field and adjacent areas in order to suggest ways in which oil recovery can be improved. Indeed, the decline of oil production to marginally economic levels in recent years has made this type of analysis timely and practical. Key technical advancements being sought include understanding the relationship of requisite strain to production in Gilbertown reservoirs, incorporation of synsedimentary growth factors into models of area balance, quantification of the relationship between requisite strain and bed curvature, determination of the timing of hydrocarbon generation, and identification of the avenues and mechanisms of fluid transport.

  17. Evaluation of dredged material proposed for ocean disposal from Shark River Project area

    SciTech Connect (OSTI)

    Antrim, L.D.; Gardiner, W.W.; Barrows, E.S.; Borde, A.B. [Battelle/Marine Sciences Lab., Sequim, WA (United States)

    1996-09-01T23:59:59.000Z

    The objective of the Shark River Project was to evaluate proposed dredged material to determine its suitability for unconfined ocean disposal at the Mud Dump Site. Tests and analyses were conducted on the Shark River sediments. The evaluation of proposed dredged material consisted of bulk sediment chemical and physical analysis, chemical analyses of dredging site water and elutriate, water-column and benthic acute toxicity tests, and bioaccumulation tests. Individual sediment core samples collected from the Shark River were analyzed for grain size, moisture content, and total organic carbon (TOC). One sediment composite was analyzed for bulk density, specific gravity, metals, chlorinated pesticides, polychlorinated biphenyl (PCB) congeners, polynuclear aromatic hydrocarbons (PAHs), and 1,4- dichlorobenzene. Dredging site water and elutriate, prepared from suspended-particulate phase (SPP) of the Shark River sediment composite, were analyzed for metals, pesticides, and PCBs. Benthic acute toxicity tests and bioaccumulation tests were performed.

  18. LANL Virtual Center for Chemical Hydrogen Storage: Chemical Hydrogen Storage Using Ultra-high Surface Area Main Group Materials

    SciTech Connect (OSTI)

    Susan M. Kauzlarich; Phillip P. Power; Doinita Neiner; Alex Pickering; Eric Rivard; Bobby Ellis, T. M.; Atkins, A. Merrill; R. Wolf; Julia Wang

    2010-09-05T23:59:59.000Z

    The focus of the project was to design and synthesize light element compounds and nanomaterials that will reversibly store molecular hydrogen for hydrogen storage materials. The primary targets investigated during the last year were amine and hydrogen terminated silicon (Si) nanoparticles, Si alloyed with lighter elements (carbon (C) and boron (B)) and boron nanoparticles. The large surface area of nanoparticles should facilitate a favorable weight to volume ratio, while the low molecular weight elements such as B, nitrogen (N), and Si exist in a variety of inexpensive and readily available precursors. Furthermore, small NPs of Si are nontoxic and non-corrosive. Insights gained from these studies will be applied toward the design and synthesis of hydrogen storage materials that meet the DOE 2010 hydrogen storage targets: cost, hydrogen capacity and reversibility. Two primary routes were explored for the production of nanoparticles smaller than 10 nm in diameter. The first was the reduction of the elemental halides to achieve nanomaterials with chloride surface termination that could subsequently be replaced with amine or hydrogen. The second was the reaction of alkali metal Si or Si alloys with ammonium halides to produce hydrogen capped nanomaterials. These materials were characterized via X-ray powder diffraction, TEM, FTIR, TG/DSC, and NMR spectroscopy.

  19. Environmental effects of dredging. Interim guidance for predicting quality of effluent discharged from confined dredged material disposal areas--test procedures. Technical note

    SciTech Connect (OSTI)

    Palermo, M.R.; Engler, R.M.

    1985-06-01T23:59:59.000Z

    The purpose of the following series of technical notes describe the functions necessary for predicting the quality of effluent discharged from confined dredged material disposal areas during dredging operations.

  20. Method and Case Study for Estimating the Ramping Capability of a Control Area or Balancing Authority and Implications for Moderate or High Wind Penetration: Preprint

    SciTech Connect (OSTI)

    Kirby, B.; Milligan, M.

    2005-05-01T23:59:59.000Z

    In several regions of the United States there has been a significant increase in wind generation capability over the past several years. As the penetration rate of wind capacity increases, grid operators and planners are increasingly concerned about accommodating the increased variability that wind contributes to the system. In this paper we examine the distinction between regulation, load following, hourly energy, and energy imbalance to understand how restructured power systems accommodate and value inter-hour ramps. We use data from two restructured markets, California and PJM, and from Western Area Power Administration's (WAPA's) Rocky Mountain control area to determine expected load-following capability in each region. Our approach is to examine the load-following capability that currently exists using data from existing generators in the region. We then examine the levels of wind penetration that can be accommodated with this capability using recently collected wind farm data. We discuss how load-following costs are captured in restructured markets, what resources are available to meet these requirements, why there are no explicit load-following tariffs, and the societal importance of being able to access generator ramping capability. Finally, the implications for wind plants and wind integration costs are examined.

  1. Material Disposal Areas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Permit in its next request for permit modification. MDA V MDA V is categorized as a radiological facility. It consists of three historic wastewater absorption beds that...

  2. Energy balance and partition in Inner Mongolia steppe ecosystems with different land use types

    E-Print Network [OSTI]

    Chen, Jiquan

    Energy balance and partition in Inner Mongolia steppe ecosystems with different land use types surface, including radiation balance, energy partitioning, aerodynamic characteristics, leaf area index records of the surface energy balance are currently available for grassland ecosystems, especially

  3. California Energy Balance ENVIRONMENTAL AREA RESEARCH

    E-Print Network [OSTI]

    consumption for about 25 energy products. Due to inconsistencies between the total data. CALEB v2 manages data from 1990 to 2008 on energy supply, transformation, and enduse consumption). CALEB manages data collected from 1990 to 2003 on energy supply, transformation, and enduse

  4. Energy balance in peridynamics.

    SciTech Connect (OSTI)

    Lehoucq, Richard B.; Silling, Stewart Andrew

    2010-09-01T23:59:59.000Z

    The peridynamic model of solid mechanics treats internal forces within a continuum through interactions across finite distances. These forces are determined through a constitutive model that, in the case of an elastic material, permits the strain energy density at a point to depend on the collective deformation of all the material within some finite distance of it. The forces between points are evaluated from the Frechet derivative of this strain energy density with respect to the deformation map. The resulting equation of motion is an integro-differential equation written in terms of these interparticle forces, rather than the traditional stress tensor field. Recent work on peridynamics has elucidated the energy balance in the presence of these long-range forces. We have derived the appropriate analogue of stress power, called absorbed power, that leads to a satisfactory definition of internal energy. This internal energy is additive, allowing us to meaningfully define an internal energy density field in the body. An expression for the local first law of thermodynamics within peridynamics combines this mechanical component, the absorbed power, with heat transport. The global statement of the energy balance over a subregion can be expressed in a form in which the mechanical and thermal terms contain only interactions between the interior of the subregion and the exterior, in a form anticipated by Noll in 1955. The local form of this first law within peridynamics, coupled with the second law as expressed in the Clausius-Duhem inequality, is amenable to the Coleman-Noll procedure for deriving restrictions on the constitutive model for thermomechanical response. Using an idea suggested by Fried in the context of systems of discrete particles, this procedure leads to a dissipation inequality for peridynamics that has a surprising form. It also leads to a thermodynamically consistent way to treat damage within the theory, shedding light on how damage, including the nucleation and advance of cracks, should be incorporated into a constitutive model.

  5. Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)Integrated Codes |IsLove Your Home andDisposition | NationalMaterials

  6. TEMPERATURE DISTRIBUTION AND ENERGY BALANCE IN THE ELECTRODE DURING GMAW

    E-Print Network [OSTI]

    Eagar, Thomas W.

    I ll l ). TEMPERATURE DISTRIBUTION AND ENERGY BALANCE IN THE ELECTRODE DURING GMAW Yong-Seog Kim and Energy Balance in the Electrode during GMAW by Yong-Seog Kim and T.W. Eagar Department of Materials shielding gases (argon, helium, and C02) using the PHOENICS computer code. An energy balance analysis

  7. materials so as to avoid populated areas (13). Furthermore, the inevitable transferal of risk from one community to another raises

    E-Print Network [OSTI]

    Barkan, Christopher P.L.

    and Christopher P. L. Barkan 65 Hazardous materials traffic originates and terminates at numerous locations of security concerns and several fatal railroad hazardous materials accidents, railroads' interest in all possible means of reduc- ing hazardous materials transportation risk has intensified in recent years

  8. Surface Energy Balance Measurements Above an Exurban Residential Neighbourhood of Kansas City, Missouri

    E-Print Network [OSTI]

    Balogun, Ahmed A.; Adegoke, Jimmy O.; Vezhapparambu, Sajith; Mauder, Matthias; McFadden, Joseph P.; Gallo, Kevin

    2009-01-01T23:59:59.000Z

    and energy ?ows within cities and their surrounding areas.energy balance measurements over a new exurban residential area near Kansas City,

  9. MATERIAL TRACKING USING LANMAS

    SciTech Connect (OSTI)

    Armstrong, F.

    2010-06-07T23:59:59.000Z

    LANMAS is a transaction-based nuclear material accountability software product developed to replace outdated and legacy accountability systems throughout the DOE. The core underlying purpose of LANMAS is to track nuclear materials inventory and report transactions (movement, mixing, splitting, decay, etc.) to the Nuclear Materials Management and Safeguards System (NMMSS). While LANMAS performs those functions well, there are many additional functions provided by the software product. As a material is received onto a site or created at a site, its entire lifecycle can be tracked in LANMAS complete to its termination of safeguards. There are separate functions to track material movements between and within material balance areas (MBAs). The level of detail for movements within a MBA is configurable by each site and can be as high as a site designation or as detailed as building/room/rack/row/position. Functionality exists to track the processing of materials, either as individual items or by modeling a bulk process as an individual item to track inputs and outputs from the process. In cases where sites have specialized needs, the system is designed to be flexible so that site specific functionality can be integrated into the product. This paper will demonstrate how the software can be used to input material into an account and track it to its termination of safeguards.

  10. Scintillator material

    DOE Patents [OSTI]

    Anderson, David F. (Batavia, IL); Kross, Brian J. (Aurora, IL)

    1994-01-01T23:59:59.000Z

    An improved scintillator material comprising cerium fluoride is disclosed. Cerium fluoride has been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to known scintillator materials such as thallium-doped sodium iodide, barium fluoride and bismuth germanate. As a result, cerium fluoride is favorably suited for use as a scintillator material in positron emission tomography.

  11. Scintillator material

    DOE Patents [OSTI]

    Anderson, David F. (Batavia, IL); Kross, Brian J. (Aurora, IL)

    1992-01-01T23:59:59.000Z

    An improved scintillator material comprising cerium fluoride is disclosed. Cerium fluoride has been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to known scintillator materials such as thallium-doped sodium iodide, barium fluoride and bismuth germanate. As a result, cerium fluoride is favorably suited for use as a scintillator material in positron emission tomography.

  12. Scintillator material

    DOE Patents [OSTI]

    Anderson, D.F.; Kross, B.J.

    1992-07-28T23:59:59.000Z

    An improved scintillator material comprising cerium fluoride is disclosed. Cerium fluoride has been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to known scintillator materials such as thallium-doped sodium iodide, barium fluoride and bismuth germanate. As a result, cerium fluoride is favorably suited for use as a scintillator material in positron emission tomography. 4 figs.

  13. Scintillator material

    DOE Patents [OSTI]

    Anderson, D.F.; Kross, B.J.

    1994-06-07T23:59:59.000Z

    An improved scintillator material comprising cerium fluoride is disclosed. Cerium fluoride has been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to known scintillator materials such as thallium-doped sodium iodide, barium fluoride and bismuth germanate. As a result, cerium fluoride is favorably suited for use as a scintillator material in positron emission tomography. 4 figs.

  14. Balance Calibration – A Method for Assigning a Direct-Reading Uncertainty to an Electronic Balance.

    SciTech Connect (OSTI)

    Mike Stears

    2010-07-01T23:59:59.000Z

    Paper Title: Balance Calibration – A method for assigning a direct-reading uncertainty to an electronic balance. Intended Audience: Those who calibrate or use electronic balances. Abstract: As a calibration facility, we provide on-site (at the customer’s location) calibrations of electronic balances for customers within our company. In our experience, most of our customers are not using their balance as a comparator, but simply putting an unknown quantity on the balance and reading the displayed mass value. Manufacturer’s specifications for balances typically include specifications such as readability, repeatability, linearity, and sensitivity temperature drift, but what does this all mean when the balance user simply reads the displayed mass value and accepts the reading as the true value? This paper discusses a method for assigning a direct-reading uncertainty to a balance based upon the observed calibration data and the environment where the balance is being used. The method requires input from the customer regarding the environment where the balance is used and encourages discussion with the customer regarding sources of uncertainty and possible means for improvement; the calibration process becomes an educational opportunity for the balance user as well as calibration personnel. This paper will cover the uncertainty analysis applied to the calibration weights used for the field calibration of balances; the uncertainty is calculated over the range of environmental conditions typically encountered in the field and the resulting range of air density. The temperature stability in the area of the balance is discussed with the customer and the temperature range over which the balance calibration is valid is decided upon; the decision is based upon the uncertainty needs of the customer and the desired rigor in monitoring by the customer. Once the environmental limitations are decided, the calibration is performed and the measurement data is entered into a custom spreadsheet. The spreadsheet uses measurement results, along with the manufacturer’s specifications, to assign a direct-read measurement uncertainty to the balance. The fact that the assigned uncertainty is a best-case uncertainty is discussed with the customer; the assigned uncertainty contains no allowance for contributions associated with the unknown weighing sample, such as density, static charges, magnetism, etc. The attendee will learn uncertainty considerations associated with balance calibrations along with one method for assigning an uncertainty to a balance used for non-comparison measurements.

  15. Material Balance Report NRC 742u

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:AdministrationAnalysisDarby/%2AOU1a ComplexMaersk LineManhattan1Y-12

  16. Material Balance Report NRC 742u

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:AdministrationAnalysisDarby/%2AOU1a ComplexMaersk

  17. Material Balance Report NRC 742u

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:AdministrationAnalysisDarby/%2AOU1a ComplexMaersk2*** Company Name

  18. Material Balance Report NRC 742u

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:AdministrationAnalysisDarby/%2AOU1a ComplexMaersk2*** Company Name

  19. Material Balance Report NRC 742u

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:AdministrationAnalysisDarby/%2AOU1a ComplexMaersk2*** Company Name.A

  20. Material Balance Report NRC 742u

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA Approved:AdministrationAnalysisDarby/%2AOU1a ComplexMaersk2*** Company

  1. Laboratory Evaluation of Base Materials for Neutralization of the Contaminated Aquifer at the F-Area Seepage Basins

    SciTech Connect (OSTI)

    Serkiz, S.M.

    2001-09-11T23:59:59.000Z

    Laboratory studies were performed to support field-testing of base injection into the F-Area Seepage Basins groundwater. The general purpose of these experiments is to provide information to guide the test of base injection and to identify potential adverse effects.

  2. Large-area electrochromic coatings: Composites of polyaniline and polyacrylate-silica hybrid sol-gel materials

    SciTech Connect (OSTI)

    Jang, G.W.; Chen, C.; Gumbs, R.W. [Gumbs Associates, Inc., East Brunswick, NJ (United States); Wei, Y.; Yeh, J.M. [Drexel Univ., Philadelphia, PA (United States). Dept. of Chemistry

    1996-08-01T23:59:59.000Z

    A low-cost technique for fabricating large-area electrochromic coatings is described. Polyaniline was incorporated into polyacrylate-silica hybrid sol-gel networks using suspended particles or solutions. A solution of polyaniline and poly[methyl methacrylate-co-3-(trimethoxysilyl)propyl methacrylate] can be spray- or brush-coated on transparent indium-tin oxide substrates to form robust electrochromic coatings. Silane functional groups on the polyacrylate chain act as coupling and cross-linking agents to improve surface adhesion and mechanical properties of the resulting composite coatings. These coatings showed reversible transparent to green color change when polarized at potentials between {minus}0.4 and +0.4 V vs. Ag/AgCl in a 0.2 M LiClO{sub 4}/acetonitrile electrolyte solution. The cycle lifetimes of polyaniline films were improved by incorporating the polymer in the polyacrylate-silica matrix. Electrochromic switching was demonstrated for the composite coatings in large-area all-solid-state devices.

  3. Characterizing Ultrafine Particle Exposures in Two Types of Indoor Environments: San Francisco Bay Area Classrooms and Beijing High-Rise Apartments

    E-Print Network [OSTI]

    Mullen, Nasim Ayoubzadeh

    2011-01-01T23:59:59.000Z

    point is this material balance equation: dN in E = + ( ? N +to E(t) in the material-balance equation. Consequently, forEquation (3.1) provides a mathematical description of the particle material balance

  4. Magnetic fusion energy plasma interactive and high heat flux components. Volume I. Technical assessment of the critical issues and problem areas in the plasma materials interaction field

    SciTech Connect (OSTI)

    Conn, R.W.; Gauster, W.B.; Heifetz, D.; Marmar, E.; Wilson, K.L. (eds.)

    1984-01-01T23:59:59.000Z

    A technical assessment of the critical issues and problem areas in the field of plasma materials interactions (PMI) in magnetic fusion devices shows these problems to be central for near-term experiments, for intermediate-range reactor devices including D-T burning physics experiments, and for long-term reactor machines. Critical technical issues are ones central to understanding and successful operation of existing and near-term experiments/reactors or devices of great importance for the long run, i.e., ones which will require an extensive, long-term development effort and thus should receive attention now. Four subgroups were formed to assess the critical PMI issues along four major lines: (1) PMI and plasma confinement physics experiments; (2) plasma-edge modelling and theory; (3) surface physics; and (4) materials technology for in-vessel components and the first wall. The report which follows is divided into four major sections, one for each of these topics.

  5. Load Balancing Scientific Applications

    E-Print Network [OSTI]

    Pearce, Olga

    2014-12-08T23:59:59.000Z

    The largest supercomputers have millions of independent processors, and concurrency levels are rapidly increasing. For ideal efficiency, developers of the simulations that run on these machines must ensure that computational work is evenly balanced...

  6. Load Balancing Scientific Applications 

    E-Print Network [OSTI]

    Pearce, Olga

    2014-12-08T23:59:59.000Z

    The largest supercomputers have millions of independent processors, and concurrency levels are rapidly increasing. For ideal efficiency, developers of the simulations that run on these machines must ensure that computational work is evenly balanced...

  7. Detailed balance analysis of nanophotonic solar cells

    E-Print Network [OSTI]

    Fan, Shanhui

    Detailed balance analysis of nanophotonic solar cells Sunil Sandhu, Zongfu Yu, and Shanhui Fan-voltage characteristic modeling of nanophotonic solar cells. This approach takes into account the intrinsic material non-idealities, and is useful for determining the theoretical limit of solar cell efficiency for a given structure. Our approach

  8. MATERIAL CONTROL ACCOUNTING INMM

    SciTech Connect (OSTI)

    Hasty, T.

    2009-06-14T23:59:59.000Z

    Since 1996, the Mining and Chemical Combine (MCC - formerly known as K-26), and the United States Department of Energy (DOE) have been cooperating under the cooperative Nuclear Material Protection, Control and Accounting (MPC&A) Program between the Russian Federation and the U.S. Governments. Since MCC continues to operate a reactor for steam and electricity production for the site and city of Zheleznogorsk which results in production of the weapons grade plutonium, one of the goals of the MPC&A program is to support implementation of an expanded comprehensive nuclear material control and accounting (MC&A) program. To date MCC has completed upgrades identified in the initial gap analysis and documented in the site MC&A Plan and is implementing additional upgrades identified during an update to the gap analysis. The scope of these upgrades includes implementation of MCC organization structure relating to MC&A, establishing material balance area structure for special nuclear materials (SNM) storage and bulk processing areas, and material control functions including SNM portal monitors at target locations. Material accounting function upgrades include enhancements in the conduct of physical inventories, limit of error inventory difference procedure enhancements, implementation of basic computerized accounting system for four SNM storage areas, implementation of measurement equipment for improved accountability reporting, and both new and revised site-level MC&A procedures. This paper will discuss the implementation of MC&A upgrades at MCC based on the requirements established in the comprehensive MC&A plan developed by the Mining and Chemical Combine as part of the MPC&A Program.

  9. SURF 2005; final report Load Balancing Strategies for

    E-Print Network [OSTI]

    SURF 2005; final report Load Balancing Strategies for Parallel SAMR Algorithms A Study of partial differential equations are important in many areas of science and technology. Only adaptive mesh in a load-balanced manner is even more difficult than for unstructured mesh refinement techniques. Therefore

  10. Multidimensional spectral load balancing

    SciTech Connect (OSTI)

    Hendrickson, B.; Leland, R.

    1993-01-01T23:59:59.000Z

    We describe an algorithm for the static load balancing of scientific computations that generalizes and improves upon spectral bisection. Through a novel use of multiple eigenvectors, our new spectral algorithm can divide a computation into 4 or 8 pieces at once. These multidimensional spectral partitioning algorithms generate balanced partitions that have lower communication overhead and are less expensive to compute than those produced by spectral bisection. In addition, they automatically work to minimize message contention on a hypercube or mesh architecture. These spectral partitions are further improved by a multidimensional generalization of the Kernighan-Lin graph partitioning algorithm. Results on several computational grids are given and compared with other popular methods.

  11. Lightweighting Materials | Clean Energy | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ORNL conducts lightweight materials research in several areas: materials development, properties and manufacturing, computational materials science, and multi-material enabling...

  12. HIGHWAY INFRASTRUCTURE FOCUS AREA NEXT-GENERATION INFRASTRUCTURE MATERIALS VOLUME I - TECHNICAL PROPOSAL & MANAGEMENTENHANCEMENT OF TRANSPORTATION INFRASTRUCTURE WITH IRON-BASED AMORPHOUS-METAL AND CERAMIC COATINGS

    SciTech Connect (OSTI)

    Farmer, J C

    2007-12-04T23:59:59.000Z

    The infrastructure for transportation in the United States allows for a high level of mobility and freight activity for the current population of 300 million residents, and several million business establishments. According to a Department of Transportation study, more than 230 million motor vehicles, ships, airplanes, and railroads cars were used on 6.4 million kilometers (4 million miles) of highways, railroads, airports, and waterways in 1998. Pipelines and storage tanks were considered to be part of this deteriorating infrastructure. The annual direct cost of corrosion in the infrastructure category was estimated to be approximately $22.6 billion in 1998. There were 583,000 bridges in the United States in 1998. Of this total, 200,000 bridges were steel, 235,000 were conventional reinforced concrete, 108,000 bridges were constructed using pre-stressed concrete, and the balance was made using other materials of construction. Approximately 15 percent of the bridges accounted for at this point in time were structurally deficient, primarily due to corrosion of steel and steel reinforcement. Iron-based amorphous metals, including SAM2X5 (Fe{sub 49.7}Cr{sub 17.7}Mn{sub 1.9}Mo{sub 7.4}W{sub 1.6}B{sub 15.2}C{sub 3.8}Si{sub 2.4}) and SAM1651 (Fe{sub 48}Mo{sub 14}Cr{sub 15}Y{sub 2}C{sub 15}B{sub 6}) have been developed, and have very good corrosion resistance. These materials have been prepared as a melt-spun ribbons, as well as gas atomized powders and thermal-spray coatings. During electrochemical testing in several environments, including seawater at 90 C, the passive film stabilities of these materials were found to be comparable to that of more expensive high-performance alloys, based on electrochemical measurements of the passive film breakdown potential and general corrosion rates. These materials also performed very well in standard salt fog tests. Chromium (Cr), molybdenum (Mo) and tungsten (W) provided corrosion resistance, and boron (B) enabled glass formation. The high boron content of this particular amorphous metal made it an effective neutron absorber, and suitable for criticality control applications. These amorphous alloys appear to maintain their corrosion resistance up to the glass transition temperature. Visionary research is proposed to extend the application of corrosion-resistant iron-based amorphous metal coatings, and variants of these coatings, to protection of the Nation's transportation infrastructure. Specific objectives of the proposed work are: (1) fabrication of appropriate test samples for evaluation of concept; (2) collection of production and test data for coated steel reinforcement bars, enabling systematic comparison of various coating options, based upon performance and economic considerations; and (3) construction and testing of concrete structures with coated steel reinforcement bars, thereby demonstrating the value of amorphous-metal coatings. The benefits of ceramic coatings as thermal barriers will also be addressed.

  13. Decision-directed materials-accounting procedures: an overview

    SciTech Connect (OSTI)

    Shipley, J.P.

    1981-01-01T23:59:59.000Z

    With materials balances taken at intervals, methods for treating materials balance data and their use by safeguards decision-making are relatively straightforward. The emphasis on accounting in which balances may be drawn on a daily or weekly basis, raises anew questions in these two areas: (1) what is the most effective means of extracting the maximum amount of information; and (2) how should safeguards decision-makers use the results, and what impact does the decision process have on the analysis techniques. These questions lead to considering combinations of materials balances, which exposes a whole new set of concerns. For example, we must select the most appropriate combinations, which implies some consideration of possible diversion scenarios, such as abrupt or protracted. Control of the overall false-alarm rate is an important requisite of the composite procedure. Significant work has been done on loss estimators, but their role in the materials accounting decision process has only begun to be examined. Current criteria may require periodic statements with respect to materials loss; the analysis procedures must be structured to provide such information. This paper presents an overview of the current technology. Questions still to be answered are pointed out.

  14. Corrective Action Investigation Plan for Corrective Action Unit 529: Area 25 Contaminated Materials, Nevada Test Site, Nevada, Rev. 0, Including Record of Technical Change No. 1

    SciTech Connect (OSTI)

    U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office

    2003-02-26T23:59:59.000Z

    This Corrective Action Investigation Plan contains the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office's approach to collect the data necessary to evaluate corrective action alternatives appropriate for the closure of Corrective Action Unit (CAU) 529, Area 25 Contaminated Materials, Nevada Test Site (NTS), Nevada, under the Federal Facility Agreement and Consent Order. CAU 529 consists of one Corrective Action Site (25-23-17). For the purpose of this investigation, the Corrective Action Site has been divided into nine parcels based on the separate and distinct releases. A conceptual site model was developed for each parcel to address the translocation of contaminants from each release. The results of this investigation will be used to support a defensible evaluation of corrective action alternatives in the corrective action decision document.

  15. Integrated Water Treatment System (IWTS) Process Flow Diagram Mass Balance Calculations for K West Basin

    SciTech Connect (OSTI)

    REED, A.V.

    2000-02-28T23:59:59.000Z

    The purpose of this calculation is to develop the rational for the material balances that are documented in the KW Basin water system Level 1 process flow diagrams.

  16. Focus Areas | Critical Materials Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC) Environmental Assessments (EA)Budget(DANCE) Target 1 FlightFlynn selected forFocus

  17. 3, 27892812, 2006 Energy balance

    E-Print Network [OSTI]

    Boyer, Edmond

    HESSD 3, 2789­2812, 2006 Energy balance closure F. Bagayoko et al. Title Page Abstract Introduction-access review for the journal Hydrology and Earth System Sciences Energy balance closure and footprint analysis (n.c.vandegiesen@citg.tudelft.nl) 2789 #12;HESSD 3, 2789­2812, 2006 Energy balance closure F

  18. Final Environmental Impact Statement for the Proposed Relocation of Technical Area 18 Capabilities and Materials at the Los Alamos National Laboratory

    SciTech Connect (OSTI)

    N /A

    2002-09-20T23:59:59.000Z

    The National Nuclear Security Administration, a separately organized agency within DOE, is responsible for providing the Nation with nuclear weapons, ensuring the safety and reliability of those nuclear weapons, and supporting programs that reduce global nuclear proliferation. These missions are accomplished with a core team of highly trained nuclear experts. One of the major training facilities for these personnel is located at Technical Area 18 (TA-18), within the Los Alamos National Laboratory (LANL), Los Alamos, New Mexico. Principal TA-18 operational activities involve research in and the design, development, construction, and application of experiments on nuclear criticality. Though TA-18 is judged to be secure by DOE's independent inspection office, its buildings and infrastructure are from 30 to more than 50 years old and are increasingly expensive to maintain and operate. Additionally, the TA-18 operations are located in a relatively isolated area, resulting in increasingly high costs to maintain a security Category I infrastructure. NNSA wishes to maintain the important capabilities currently provided at TA-18 in a manner that reduces the long-term costs for safeguards and security. NNSA proposes to accomplish this by relocating the TA-18 security Category I/II capabilities and materials to new locations. The TA-18 Relocation EIS evaluates the potential direct, indirect, and cumulative environmental impacts associated with this proposed action at the following DOE sites: (1) a different site at LANL at Los Alamos, New Mexico; (2) the Sandia National Laboratories/New Mexico at Albuquerque, New Mexico; (3) the Nevada Test Site near Las Vegas, Nevada (the Preferred Alternative); and (4) the Argonne National Laboratory-West near Idaho Falls, Idaho. The EIS also analyzes the alternatives of upgrading the existing TA-18 facilities and the No Action Alternative of maintaining the operations at the current TA-18 location.

  19. Fate and transport processes controlling the migration of hazardous and radioactive materials from the Area 5 Radioactive Waste Management Site (RWMS)

    SciTech Connect (OSTI)

    Estrella, R.

    1994-10-01T23:59:59.000Z

    Desert vadose zones have been considered as suitable environments for the safe and long-term isolation of hazardous wastes. Low precipitation, high evapotranspiration and thick unsaturated alluvial deposits commonly found in deserts make them attractive as waste disposal sites. The fate and transport of any contaminant in the subsurface is ultimately determined by the operating retention and transformation processes in the system and the end result of the interactions among them. Retention (sorption) and transformation are the two major processes that affect the amount of a contaminant present and available for transport. Retention processes do not affect the total amount of a contaminant in the soil system, but rather decrease or eliminate the amount available for transport at a given point in time. Sorption reactions retard the contaminant migration. Permanent binding of solute by the sorbent is also possible. These processes and their interactions are controlled by the nature of the hazardous waste, the properties of the porous media and the geochemical and environmental conditions (temperature, moisture and vegetation). The present study summarizes the available data and investigates the fate and transport processes that govern the migration of contaminants from the Radioactive Waste Management Site (RWMS) in Area 5 of the Nevada Test Site (NTS). While the site is currently used only for low-level radioactive waste disposal, past practices have included burial of material now considered hazardous. Fundamentals of chemical and biological transformation processes are discussed subsequently, followed by a discussion of relevant results.

  20. Addendum to the Corrective Action Decision Document/Closure Report for Corrective Action Unit 529: Area 25 Contaminated Materials, Nevada Test Site, Nevada, Revision 1

    SciTech Connect (OSTI)

    Krauss, Mark J

    2013-10-01T23:59:59.000Z

    This document constitutes an addendum to the Corrective Action Decision Document/Closure Report for Corrective Action Unit 529: Area 25 Contaminated Materials, Nevada Test Site, Nevada as described in the document Recommendations and Justifications To Remove Use Restrictions Established under the U.S. Department of Energy, National Nuclear Security Administration Nevada Field Office Federal Facility Agreement and Consent Order dated September 2013. The Use Restriction (UR) Removal document was approved by the Nevada Division of Environmental Protection on October 16, 2013. The approval of the UR Removal document constituted approval of each of the recommended UR removals. In conformance with the UR Removal document, this addendum consists of: This page that refers the reader to the UR Removal document for additional information The cover, title, and signature pages of the UR Removal document The NDEP approval letter The corresponding section of the UR Removal document This addendum provides the documentation justifying the cancellation of the UR for CAS 25-23-17, Contaminated Wash (Parcel H). This UR was established as part of FFACO corrective actions and was based on the presence of total petroleum hydrocarbon diesel-range organics contamination at concentrations greater than the NDEP action level at the time of the initial investigation.

  1. Balance-sheet trends

    E-Print Network [OSTI]

    Cox, Gilford W

    1949-01-01T23:59:59.000Z

    on ths following two oppos1te pages) g5 The above tabulation indicates that the account fora 1s greatly favored+ Hose accountants think thst fros an analysis point of view the account fora is batter~ because when this fore is properly set ups 1t... the net redaction ?as hsought about. The "Staten?at of Legal Capital" sho?? the capital stock and surplus for the beginning of the accounting period, 44u+in "Bo %e Need a Balance SheetT", the Journal of Account vole Liight ppe 343 47m the pa+fit fram...

  2. Corrective Action Decision Document for Corrective Action Unit 168: Area 25 and 26 Contaminated Materials and Waste Dumps, Nevada Test Site, Nevada, Rev. No.: 2 with Errata Sheet

    SciTech Connect (OSTI)

    Wickline, Alfred

    2006-12-01T23:59:59.000Z

    This Corrective Action Decision Document has been prepared for Corrective Action Unit (CAU) 168: Area 25 and 26, Contaminated Materials and Waste Dumps, Nevada Test Site, Nevada. The purpose of this Corrective Action Decision Document is to identify and provide a rationale for the selection of a recommended corrective action alternative for each corrective action site (CAS) within CAU 168. The corrective action investigation (CAI) was conducted in accordance with the ''Corrective Action Investigation Plan for Corrective Action Unit 168: Area 25 and 26, Contaminated Materials and Waste Dumps, Nevada Test Site, Nevada'', as developed under the ''Federal Facility Agreement and Consent Order'' (1996). Corrective Action Unit 168 is located in Areas 25 and 26 of the Nevada Test Site, Nevada and is comprised of the following 12 CASs: CAS 25-16-01, Construction Waste Pile; CAS 25-16-03, MX Construction Landfill; CAS 25-19-02, Waste Disposal Site; CAS 25-23-02, Radioactive Storage RR Cars; CAS 25-23-13, ETL - Lab Radioactive Contamination; CAS 25-23-18, Radioactive Material Storage; CAS 25-34-01, NRDS Contaminated Bunker; CAS 25-34-02, NRDS Contaminated Bunker; CAS 25-99-16, USW G3; CAS 26-08-01, Waste Dump/Burn Pit; CAS 26-17-01, Pluto Waste Holding Area; and CAS 26-19-02, Contaminated Waste Dump No.2. Analytes detected during the CAI were evaluated against preliminary action levels (PALs) to determine contaminants of concern (COCs) for CASs within CAU 168. Radiological measurements of railroad cars and test equipment were compared to unrestricted (free) release criteria. Assessment of the data generated from the CAI activities revealed the following: (1) Corrective Action Site 25-16-01 contains hydrocarbon-contaminated soil at concentrations exceeding the PAL. The contamination is at discrete locations associated with asphalt debris. (2) No COCs were identified at CAS 25-16-03. Buried construction waste is present in at least two disposal cells contained within the landfill boundaries. (3) No COCs were identified at CAS 25-19-02. (4) Radiological surveys at CAS 25-23-02 identified 13 railroad cars that exceeded the NV/YMP Radiological Control Manual limits for free release. Six railroad cars were below these limits and therefore met the free-release criteria. (5) An In-Situ Object Counting System survey taken at CAS 25-23-02 identified two railroad cars possibly containing fuel fragments; both exceeded the NV/YMP Radiological Control Manual free release criteria. (6) Corrective Action Site 25-23-18 contains total petroleum hydrocarbons-diesel-range organics, Aroclor-1260, uranium-234, uranium-235, strontium-90, and cesium-137 that exceed PALs. (7) Radiological surveys at CAS 25-34-01 indicate that there were no total contamination readings that exceeded the NV/YMP Radiological Control Manual limits for free release. (8) Radiological surveys at CAS 25-34-02 indicate that there were no total contamination readings that exceeded the NV/YMP Radiological Control Manual limits for free release. (9) Radiological surveys at CAS 25-23-13 identified six pieces of equipment that exceed the NV/YMP Radiological Control Manual limits for free release. (10) Corrective Action Site 25-99-16 was not investigated. A review of historical documentation and current site conditions showed that no further characterization was required to select the appropriate corrective action. (11) Corrective Action Site 26-08-01 contains hydrocarbon-contaminated soil at concentrations exceeding the PAL. The contamination is at discrete locations associated with asphalt debris. (12) Corrective Action Site 26-17-01 contains total petroleum hydrocarbons-diesel-range organics and Aroclor-1260 exceeding the PALs. (13) Radiological surveys at CAS 26-19-02 identified metallic debris that exceeded the NV/YMP Radiological Control Manual limits for free release. Concentrations of radiological or chemical constituents in soil did not exceed PALs.

  3. Dynamic load balancing of applications

    DOE Patents [OSTI]

    Wheat, S.R.

    1997-05-13T23:59:59.000Z

    An application-level method for dynamically maintaining global load balance on a parallel computer, particularly on massively parallel MIMD computers is disclosed. Global load balancing is achieved by overlapping neighborhoods of processors, where each neighborhood performs local load balancing. The method supports a large class of finite element and finite difference based applications and provides an automatic element management system to which applications are easily integrated. 13 figs.

  4. Test and evaluation of computerized nuclear material accounting methods. Final report

    SciTech Connect (OSTI)

    NONE

    1995-12-31T23:59:59.000Z

    In accordance with the definition of a Material Balance Area (MBA) as a well-defined geographical area involving an Integral operation, the building housing the BFS-1 and BFS-1 critical facilities is considered to consist of one MBA. The BFS materials are in the form of small disks clad in stainless steel and each disk with nuclear material has its own serial number. Fissile material disks in the BFS MBA can be located at three key monitoring points: BFS-1 facility, BFS-2 facility and main storage of BFS fissile materials (storage 1). When used in the BFS-1 or BFS-2 critical facilities, the fissile material disks are loaded in tubes (fuel rods) forming critical assembly cores. The following specific features of the BFS MBA should be taken into account for the purpose of computerized accounting of nuclear material: (1) very large number of nuclear material items (about 70,000 fissile material items); and (2) periodically very intensive shuffling of nuclear material items. Requirements for the computerized system are determined by basic objectives of nuclear material accounting: (1) providing accurate information on the identity and location of all items in the BFS material balance area; (2) providing accurate information on location and identity of tamper-indicating devices; (3) tracking nuclear material inventories; (4) issuing periodic reports; (5) assisting with the detection of material gains or losses; (6) providing a history of nuclear material transactions; (7) preventing unauthorized access to the system and data falsification. In August 1995, the prototype computerized accounting system was installed on the BFS facility for trial operation. Information on two nuclear material types was entered into the data base: weapon-grade plutonium metal and 36% enriched uranium dioxide. The total number of the weapon-grade plutonium disks is 12,690 and the total number of the uranium dioxide disks is 1,700.

  5. HAZARDOUS MATERIALS INCIDENTS What are hazardous materials?

    E-Print Network [OSTI]

    Fernandez, Eduardo

    HAZARDOUS MATERIALS INCIDENTS What are hazardous materials? Hazardous materials are chemicals I do if there is a small spill in the area and personnel trained in Hazardous Material clean up, or there is a small spill where personnel trained in Hazardous Material clean up or an appropriate spill kit

  6. HAZARDOUS MATERIALS INCIDENTS What are hazardous materials?

    E-Print Network [OSTI]

    Fernandez, Eduardo

    HAZARDOUS MATERIALS INCIDENTS What are hazardous materials? Hazardous materials are chemicals I do if there is a small spill in the area and personnel trained in Hazardous Material clean up spill where personnel trained in Hazardous Material clean up or an appropriate spill kit

  7. HAZARDOUS MATERIALS INCIDENTS What are hazardous materials?

    E-Print Network [OSTI]

    Fernandez, Eduardo

    HAZARDOUS MATERIALS INCIDENTS What are hazardous materials? Hazardous materials are chemicals I do if there is a small spill in the area and personnel trained in Hazardous Material clean up personnel trained in Hazardous Material clean up or an appropriate spill kit is not available? Call 561

  8. 1, 1739, 2007 Glacier balance

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    integrates water and energy balance factors to exhibit a maximum climate change signaling effect (IPCC, 1996 (South Cascade Glacier) in the lower 48 United States with ongoing measurements. Regional variationTCD 1, 17­39, 2007 Glacier balance measurement, forecasting M. S. Pelto Title Page Abstract

  9. Balancing Hydronic Systems in Multifamily Buildings

    SciTech Connect (OSTI)

    Ruch, R.; Ludwig, P.; Maurer, T.

    2014-07-01T23:59:59.000Z

    In multifamily hydronic systems, temperature imbalance may be caused by undersized piping, improperly adjusted balancing valves, inefficient water temperature and flow levels, and owner/occupant interaction with the boilers, distribution and controls. The effects of imbalance include tenant discomfort, higher energy use intensity and inefficient building operation. This paper explores cost-effective distribution upgrades and balancing measures in multifamily hydronic systems, providing a resource to contractors, auditors, and building owners on best practices to improve tenant comfort and lower operating costs. The research was conducted by The Partnership for Advanced Residential Retrofit (PARR) in conjunction with Elevate Energy. The team surveyed existing knowledge on cost-effective retrofits for optimizing distribution in typical multifamily hydronic systems, with the aim of identifying common situations and solutions, and then conducted case studies on two Chicago area buildings with known balancing issues in order to quantify the extent of temperature imbalance. At one of these buildings a booster pump was installed on a loop to an underheated wing of the building. This study found that unit temperature in a multifamily hydronic building can vary as much as 61 degrees F, particularly if windows are opened or tenants use intermittent supplemental heating sources like oven ranges. Average temperature spread at the building as a result of this retrofit decreased from 22.1 degrees F to 15.5 degrees F.

  10. Fundamentals of materials accounting for nuclear safeguards

    SciTech Connect (OSTI)

    Pillay, K.K.S. (comp.)

    1989-04-01T23:59:59.000Z

    Materials accounting is essential to providing the necessary assurance for verifying the effectiveness of a safeguards system. The use of measurements, analyses, records, and reports to maintain knowledge of the quantities of nuclear material present in a defined area of a facility and the use of physical inventories and materials balances to verify the presence of special nuclear materials are collectively known as materials accounting for nuclear safeguards. This manual, prepared as part of the resource materials for the Safeguards Technology Training Program of the US Department of Energy, addresses fundamental aspects of materials accounting, enriching and complementing them with the first-hand experiences of authors from varied disciplines. The topics range from highly technical subjects to site-specific system designs and policy discussions. This collection of papers is prepared by more than 25 professionals from the nuclear safeguards field. Representing research institutions, industries, and regulatory agencies, the authors create a unique resource for the annual course titled ''Materials Accounting for Nuclear Safeguards,'' which is offered at the Los Alamos National Laboratory.

  11. Similarity solutions for moisture redistribution, including the role of fluid-fluid interfacial area

    E-Print Network [OSTI]

    Gugat, Martin

    (solid phase) #12;Microscopic description of two-phase flow Mass balance equations Momentum balance equations #12;Macroscopic mass balance equations #12;Macroscopic momentum balance equations #12;where G a S T where are material coefficients.a S and #12;Extended theories of two-phase flow Simplified equation

  12. Capacity Requirements to Support Inter-Balancing Area Wind Delivery

    SciTech Connect (OSTI)

    Kirby, B.; Milligan, M.

    2009-07-01T23:59:59.000Z

    Paper examines the capacity requirements that arise as wind generation is integrated into the power system and how those requirements change depending on where the wind energy is delivered.

  13. Balancing Intermolecular and MoleculeSubstrate Interactions in Supramolecular Assemblies

    E-Print Network [OSTI]

    Ortega, Enrique

    Balancing Intermolecular and Molecule­Substrate Interactions in Supramolecular Assemblies By Dimas of the relevant molecular interactions by the appropriate choice of molecular species in mixed supramolecular for Materials Science 1-1 Namiki, Tsukuba 305-0044 (Japan) Dr. E. Barrena, Prof. H. Dosch ITAP, Universita

  14. Development of a generic, computerized nuclear material accountability system: NucMAS

    SciTech Connect (OSTI)

    Cornell, M.D.; O'Leary, J.M.

    1987-01-01T23:59:59.000Z

    The application NucMAS provides basic computerized accountability functions for the Savannah River Plant (SRP) Separations Department Material Balance Areas (MBA's). These functions include data entry, data management, calculations, and report generation. NucMAS can be used both for routine reporting to the SRP central Material Control and Accounting (MC and A) system and for rapid ad hoc queries in emergency situations. The system is designed to work with any process handling one or more of the 17 accountable nuclear materials specified by the Department of Energy (DOE). It relies on user-supplied configuration data to drive data prompts, report headings, data validations, and calculations.

  15. Lead carbonate scintillator materials

    DOE Patents [OSTI]

    Derenzo, Stephen E. (Pinole, CA); Moses, William W. (Berkeley, CA)

    1991-01-01T23:59:59.000Z

    Improved radiation detectors containing lead carbonate or basic lead carbonate as the scintillator element are disclosed. Both of these scintillators have been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to other known scintillator materials. The radiation detectors disclosed are favorably suited for use in general purpose detection and in medical uses.

  16. Balancing act - BPA grid responds to huge influx of wind power...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    territory A large fraction of the wind power in the Northwest is locating in the heart of BPA's transmission grid. Wind power in BPA's balancing area has grown from 25 MW 10...

  17. Current balancing for battery strings

    DOE Patents [OSTI]

    Galloway, James H. (New Baltimore, MI)

    1985-01-01T23:59:59.000Z

    A battery plant is described which features magnetic circuit means for balancing the electrical current flow through a pluraliircuitbattery strings which are connected electrically in parallel. The magnetic circuit means is associated with the battery strings such that the conductors carrying the electrical current flow through each of the battery strings pass through the magnetic circuit means in directions which cause the electromagnetic fields of at least one predetermined pair of the conductors to oppose each other. In an alternative embodiment, a low voltage converter is associated with each of the battery strings for balancing the electrical current flow through the battery strings.

  18. University Materials Institute INTRODUCTION

    E-Print Network [OSTI]

    Escolano, Francisco

    University Materials Institute INTRODUCTION The University Materials Science Institute of Alicante the needed multidisciplinary character of the materials area. It is important to highlight the fact participate in the Materials Science PhD program which is imparted at the UA. Scientific research

  19. Dual shell pressure balanced vessel

    DOE Patents [OSTI]

    Fassbender, Alexander G. (West Richland, WA)

    1992-01-01T23:59:59.000Z

    A dual-wall pressure balanced vessel for processing high viscosity slurries at high temperatures and pressures having an outer pressure vessel and an inner vessel with an annular space between the vessels pressurized at a pressure slightly less than or equivalent to the pressure within the inner vessel.

  20. Material accountancy in an electrometallurgical Fuel Conditioning Facility

    SciTech Connect (OSTI)

    Vaden, D.; Benedict, R.W.; Goff, K.M.; Keyes, R.W.; Mariani, R.D. [Argonne National Lab.-West, Idaho Falls, ID (United States); Bucher, R.G.; Yacout, A.M. [Argonne National Lab., IL (United States)

    1996-05-01T23:59:59.000Z

    The Fuel Conditioning Facility (FCF) treats spent nuclear fuel using an electrometallurgical process that separates the uranium from the fission products, sodium thermal bond and cladding materials. Material accountancy is necessary at FCF for two reasons: first, it provides a mechanism for detecting a potential loss of nuclear material for safeguards and security; second, it provides a periodic check of inventories to ensure that processes and material are under control. By weighing material entering and leaving a process, and using sampling results to determine composition, an inventory difference (ID) results when the measured inventory is compared to the predicted inventory. The ID and its uncertainty, based on error propagation, determines the degree of assurance that an operation proceeded according to expectations. FCF uses the ID calculation in two ways: closeout, which is the ID and uncertainty for a particular operational step, and material accountancy, which determines an ID and its associated uncertainty for a material balance area through several operational steps. Material accountancy over the whole facility for a specified time period assists in detecting diversion of nuclear material. Data from depleted uranium operations are presented to illustrate the method used in FCF.

  1. Balancing a two-wheeled Segway robot

    E-Print Network [OSTI]

    Bageant, Maia R. (Maia Reynolds)

    2011-01-01T23:59:59.000Z

    In this thesis, I designed and constructed hardware for a two-wheeled balancing Segway robot. Because the robot could not be balanced based on a control system derived from the original analytical model, additional system ...

  2. Entropy balance in holographic superconductors

    E-Print Network [OSTI]

    Sean A. Hartnoll; Razieh Pourhasan

    2012-05-07T23:59:59.000Z

    In systems undergoing second order phase transitions, the temperature integral of the specific heat over temperature from zero to the critical temperature is the same in both the normal and ordered phases. This entropy balance relates the critical temperature to the distribution of degrees of freedom in the normal and ordered states. Quantum criticality and fractionalization can imply an increased number of low energy degrees of freedom in both the normal and ordered states. We explore the role of entropy balance in holographic models of superconductivity, focussing on the interplay between quantum criticality and superconductivity. We consider models with and without a ground state entropy density in the normal phase; the latter models are a new class of holographic superconductors. We explain how a normal phase entropy density manifests itself in the stable superconducting phase.

  3. Balanced pressure gerotor fuel pump

    DOE Patents [OSTI]

    Raney, Michael Raymond; Maier, Eugen

    2004-08-03T23:59:59.000Z

    A gerotor pump for pressurizing gasoline fuel is capable of developing pressures up to 2.0 MPa with good mechanical and volumetric efficiency and satisfying the durability requirements for an automotive fuel pump. The pump has been designed with optimized clearances and by including features that promote the formation of lubricating films of pressurized fuel. Features of the improved pump include the use of a shadow port in the side plate opposite the outlet port to promote balancing of high fuel pressures on the opposite sides of the rotors. Inner and outer rotors have predetermined side clearances with the clearances of the outer rotor being greater than those of the inner rotor in order to promote fuel pressure balance on the sides of the outer rotor. Support of the inner rotor and a drive shaft on a single bushing with bearing sleeves maintains concentricity. Additional features are disclosed.

  4. ARM - Measurement - Surface energy balance

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadap Documentation TDMADAP : XDCnarrowbandheat flux ARM Data Discovery Browseenergy balance ARM

  5. The Science of Global Warming Energy Balance

    E-Print Network [OSTI]

    Blais, Brian

    The Science of Global Warming ·Energy Balance ·Feedback Loops Global Warming can be understood complexities ·Introduce a Simple Model of Energy Balance ·Understand the Vocabulary ·Point out some units of energy input from the Sun = Temperature: 5.3 oC Greenhouse Effect 101: A Balance is Achieved

  6. Energy Balanced Chain in Distributed Sensor Networks

    E-Print Network [OSTI]

    Howitt, Ivan

    Energy Balanced Chain in Distributed Sensor Networks Ivan Howitt Electrical & Computer Engineering because of their higher traffic. This paper suggests an energy balanced chain (EBC) which can efficiently the energy balance optimization problem in terms of the segmentation space. By adjusting the transmission

  7. 6, 33813402, 2006 The energy balance

    E-Print Network [OSTI]

    Boyer, Edmond

    ACPD 6, 3381­3402, 2006 The energy balance closure problem T. Foken et al. Title Page Abstract Discussions Some aspects of the energy balance closure problem T. Foken, F. Wimmer, M. Mauder, C. Thomas. Foken (thomas.foken@uni-bayreuth.de) 3381 #12;ACPD 6, 3381­3402, 2006 The energy balance closure problem

  8. Multiscale modeling of spatially variable water and energy balance processes

    E-Print Network [OSTI]

    Famiglietti, J. S; Wood, E. F

    1994-01-01T23:59:59.000Z

    MULTISCALE WATER AND ENERGY BALANCE MODELING Wood, E. F. ,spatially variable water and energy balance processes J. S.modeling. Water and energy balance models are developed at

  9. Urban Microclimate, a Study of Energy Balance and Fluid Dynamics /

    E-Print Network [OSTI]

    Yaghoobian, Neda

    2013-01-01T23:59:59.000Z

    The International Urban Energy Balance Models ComparisonT. Williamson, Urban surface energy balance models: modelof the international urban energy balance model comparison,

  10. Urban Microclimate, a Study of Energy Balance and Fluid Dynamics /

    E-Print Network [OSTI]

    Yaghoobian, Neda

    2013-01-01T23:59:59.000Z

    for building load calculations; Exterior heat balance (CD-for building load calculations; Exterior heat balance (CD-for Building Load Calculations; Exterior Heat Balance (CD-

  11. Corrective Action Decision Document for Corrective Action Unit 168: Areas 25 and 26 Contaminated Materials and Waste Dumps, Nevada Test Site, Nevada: Revision 0, Including Record of Technical Change No. 1

    SciTech Connect (OSTI)

    U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office

    2003-08-08T23:59:59.000Z

    This Corrective Action Decision Document identifies and rationalizes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office's selection of recommended corrective action alternatives (CAAs) to facilitate the closure of Corrective Action Unit (CAU)168: Areas 25 and 26 Contaminated Materials and Waste Dumps, Nevada Test Site (NTS), Nevada, under the Federal Facility Agreement and Consent Order. Located in Areas 25 and 26 at the NTS in Nevada, CAU 168 is comprised of twelve Corrective Action Sites (CASs). Review of data collected during the corrective action investigation, as well as consideration of current and future operations in Areas 25 and 26 of the NTS, led the way to the development of three CAAs for consideration: Alternative 1 - No Further Action; Alternative 2 - Clean Closure; and Alternative 3 - Close in Place with Administrative Controls. As a result of this evaluation, a combination of all three CAAs is recommended for this CAU. Alternative 1 was the preferred CAA for three CASs, Alternative 2 was the preferred CAA for six CASs (and nearly all of one other CAS), and Alternative 3 was the preferred CAA for two CASs (and a portion of one other CAS) to complete the closure at the CAU 168 sites. These alternatives were judged to meet all requirements for the technical components evaluated as well as all applicable state and federal regulations for closure of the sites and elimination of potential future exposure pathways to the contaminated soils at CAU 168.

  12. Porous Materials Porous Materials

    E-Print Network [OSTI]

    Berlin,Technische Universität

    1 Porous Materials x Porous Materials · Physical properties * Characteristic impedance p = p 0 e -jk xa- = vej[ ] p x - j ; Zc= p ve = c ka 0k = c 1-j #12;2 Porous Materials · Specific acoustic impedance Porous Materials · Finite thickness ­ blocked p e + -jk (x-d)a p e - jk (x-d)a d x #12

  13. Joint China-United States Report for Year 1 Insulation Materials and Systems Project Area Clean Energy Research Center Building Energy Efficiency (CERC-BEE)

    SciTech Connect (OSTI)

    Stovall, Therese K [ORNL; Biswas, Kaushik [ORNL; Song, Bo [China Academy of Building Research; Zhang, Sisi [China Academy of Building Research

    2012-08-01T23:59:59.000Z

    In November of 2009, the presidents of China and the U.S. announced the establishment of the Clean Energy Research Center (CERC). This broad research effort is co-funded by both countries and involves a large number of research centers and universities in both countries. One part of this program is focused on improving the energy efficiency of buildings. One portion of the CERC-BEE was focused on building insulation systems. The research objective of this effort was to Identify and investigate candidate high performance fire resistant building insulation technologies that meet the goal of building code compliance for exterior wall applications in green buildings in multiple climate zones. A Joint Work Plan was established between researchers at the China Academy of Building Research and Oak Ridge National Laboratory. Efforts in the first year under this plan focused on information gathering. The objective of this research program is to reduce building energy use in China via improved building insulation technology. In cold regions in China, residents often use inefficient heating systems to provide a minimal comfort level within inefficient buildings. In warmer regions, air conditioning has not been commonly used. As living standards rise, energy consumption in these regions will increase dramatically unless significant improvements are made in building energy performance. Previous efforts that defined the current state of the built environment in China and in the U.S. will be used in this research. In countries around the world, building improvements have typically followed the implementation of more stringent building codes. There have been several changes in building codes in both the U.S. and China within the last few years. New U.S. building codes have increased the amount of wall insulation required in new buildings. New government statements from multiple agencies in China have recently changed the requirements for buildings in terms of energy efficiency and fire safety. A related issue is the degree to which new standards are adopted and enforced. In the U.S., standards are developed using a consensus process, and local government agencies are free to implement these standards or to ignore them. For example, some U.S. states are still using 2003 versions of the building efficiency standards. There is also a great variation in the degree to which the locally adopted standards are enforced in different U.S. cities and states. With a more central process in China, these issues are different, but possible impacts of variable enforcement efficacy may also exist. Therefore, current building codes in China will be compared to the current state of building fire-safety and energy-efficiency codes in the U.S. and areas for possible improvements in both countries will be explored. In particular, the focus of the applications in China will be on green buildings. The terminology of 'green buildings' has different meanings to different audiences. The U.S. research is interested in both new, green buildings, and on retrofitting existing inefficient buildings. An initial effort will be made to clarify the scope of the pertinent wall insulation systems for these applications.

  14. Optimum balancing for flexible rotor

    E-Print Network [OSTI]

    Fu, Her James

    1975-01-01T23:59:59.000Z

    for the donation of vibration pick-ups and the loan of precious equipment. A special appreciation is extended to my friend, Miss Mei Ou-Yang, for her assistance, encouragement and unselfish support during the preparation and completion of this project. Last... Balancing Fig. 9 Typical Phase Lag Between Force and Vibration Amplitude Chart 14 20 Fig. 10 Typical Principal Modes for a Symmetric and Uniform Shaft 21 Fig. ll Test Rig Setup Fig. 12 Typical Rotor, Probe and Probe Stand Fig. 13 Critical Speed VS...

  15. Balancing oil and environment... responsibly.

    SciTech Connect (OSTI)

    Weimer, Walter C.; Teske, Lisa

    2007-01-25T23:59:59.000Z

    Balancing Oil and Environment…Responsibly As the price of oil continues to skyrocket and global oil production nears the brink, pursuing unconventional oil supplies, such as oil shale, oil sands, heavy oils, and oils from biomass and coal has become increasingly attractive. Of particular significance to the American way is that our continent has significant quantities of these resources. Tapping into these new resources, however, requires cutting-edge technologies for identification, production, processing and environmental management. This job needs a super hero or two for a job of this size and proportion…

  16. Energy Balance Bowen Ratio System

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField Campaign:INEAWaterCool Roofs Energy 101: CoolServices »0 Energy Balance

  17. Lithium Balance | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to: navigation, searchOf KilaueaInformation Other AlternativePark, Arizona: EnergyBalance

  18. Balance Energy | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to:EzfeedflagBiomass Conversions Inc JumpIM 2011-003 Jump to:Bahamas:Georgia:Baker,BalBalance

  19. Impact of burned areas on the northern African seasonal climate from the perspective of regional modeling

    E-Print Network [OSTI]

    de Sales, F; Xue, Y; Xue, Y; Okin, GS

    2015-01-01T23:59:59.000Z

    areas on the surface energy balance and monthly precipita-in surface available energy caused a drop in surfaceFurthermore, precipitation energy analysis revealed that

  20. Lead carbonate scintillator materials

    DOE Patents [OSTI]

    Derenzo, S.E.; Moses, W.W.

    1991-05-14T23:59:59.000Z

    Improved radiation detectors containing lead carbonate or basic lead carbonate as the scintillator element are disclosed. Both of these scintillators have been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to other known scintillator materials. The radiation detectors disclosed are favorably suited for use in general purpose detection and in medical uses. 3 figures.

  1. Workshop on innovation in materials processing and manufacture: Exploratory concepts for energy applications

    SciTech Connect (OSTI)

    Horton, L.L. [comp.

    1993-06-01T23:59:59.000Z

    The goal of the workshop was to bring together industrial, academic, and DOE Laboratory personnel to discuss and identify potential areas for which creative, innovative, and/or multidisciplinary solutions could result in major payoffs for the nation`s energy economy, DOE, and industry. The topics emphasized in these discussions were: surfaces and interfacial processing technologies, biomolecular materials, powder/precursor technologies, magnetic materials, nanoscale materials, novel ceramics and composites, novel intermetallics and alloys, environmentally benign materials, and energy efficiency. The workshop had a 2-day format. One the first day, there was an introductory session that summarized future directions within DOE`s basic and materials technology programs, and the national studies on manufacturing and materials science and engineering. The balance of the workshop was devoted to brainstorming sessions by seven working groups. During the first working group session, the entire group was divided to discuss topics on: challenges for hostile environments, novel materials in transportation technologies, novel nanoscale materials, and opportunities in biomolecular materials. For the second session, the entire group (except for the working group on biomolecular materials) was reconfigured into new working groups on: alternative pathways to energy efficiency, environmentally benign materials and processes, and waste treatment and reduction: a basic sciences approach. This report contains separate reports from each of the seven working groups.

  2. Balanced Scorecard Program | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    (pdf). This 69-page document provides information on creating and applying a balanced slate of measurements for procurement systems. Contractor Peer Review Independent Peer...

  3. World copper smelter sulfur balance-1988

    SciTech Connect (OSTI)

    Towle, S.W. (Bureau of Mines, Denver, CO (United States))

    1993-01-01T23:59:59.000Z

    In 1989, the US Bureau of Mines initiated a contract to gather engineering, operating, and environmental cost data for 1988 for 30 major foreign primary copper smelters in market economy countries. Data were collected for 29 of the designated smelters together with information on applicable environmental regulations. Materials balance data obtained were used with available data for the eight US smelters to determine the approximate extent of copper smelter sulfur emission control in 1988. A broad characterization of the status of sulfur emission control regulation was made. The 37 US and foreign smelters represented roughly 73.2% of world and 89.3% of market economy primary copper production in 1988. The 29 non-US smelters attained 55.3% control of their input sulfur in 1988. Combined with the 90.4% control of US smelters, an aggregate 63.4% sulfur control existed. Roughly 1,951,100 mt of sulfur was emitted from the 37 market economy smelters in 1988. Identifiable SO[sub 2] control regulations covered 72.4% of the 29 foreign smelters, representing 65.5% of smelting capacity. Including US smelters, 78.4% of the major market economy smelters were regulated, representing 73.1% of smelting capacity. Significant changes since 1988 that may increase sulfur emission control are noted.

  4. Understanding the carbon and greenhouse gas balance

    E-Print Network [OSTI]

    Understanding the carbon and greenhouse gas balance of forests in Britain Research Report #12;#12;Research Report Understanding the carbon and greenhouse gas balance of forests in Britain Forestry forest soil survey 29 3.5.2 Carbon storage in the main British forest soil types 30 3.5.3 Changes in soil

  5. MATERIAL HANDLING, STORAGE, AND DISPOSAL

    E-Print Network [OSTI]

    US Army Corps of Engineers

    Materials shall be stored in a manner that allows easy identification and access to labels, identification entering storage areas. All persons shall be in a safe position while materials are being loadedEM 385-1-1 XX Jun 13 14-1 SECTION 14 MATERIAL HANDLING, STORAGE, AND DISPOSAL 14.A MATERIAL

  6. Nuclear Materials Control and Accountability

    Broader source: Energy.gov (indexed) [DOE]

    June 2011 DOE STANDARD Nuclear Materials Control and Accountability U.S. Department of Energy AREA SANS Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public...

  7. Surface Energy Balance System (SEBS) Handbook

    SciTech Connect (OSTI)

    Cook, DR

    2011-02-14T23:59:59.000Z

    A Surface Energy Balance System (SEBS) has been installed collocated with each deployed ECOR system at the Southern Great Plains (SGP), North Slope of Alaska (NSA), Tropical Western Pacific (TWP), ARM Mobile Facility 1 (AMF1), and ARM Mobile Facility 2 (AMF2). The surface energy balance system consists of upwelling and downwelling solar and infrared radiometers within one net radiometer, a wetness sensor, and soil measurements. The SEBS measurements allow the comparison of ECOR sensible and latent heat fluxes with the energy balance determined from the SEBS and provide information on wetting of the sensors for data quality purposes.

  8. Surface Energy Balance of the Taylor Glacier, Antarctica

    E-Print Network [OSTI]

    Bliss, Andrew

    2005-01-01T23:59:59.000Z

    G. L. Dana. Surface energy balance and meltwater productionice sheet: a comparison of energy-balance and a degree-dayvariations in the surface energy balance of haut glacier d’

  9. Development of Energy Balances for the State of California

    E-Print Network [OSTI]

    Murtishaw, Scott; Price, Lynn; de la Rue du Can, Stephane; Masanet, Eric; Worrell, Ernst; Sahtaye, Jayant

    2005-01-01T23:59:59.000Z

    Energy Agency, 2003a. Energy Balances of OECD Countries.Energy Agency, 2003b. Energy Balances of Non-OECD Countries.for constructing the energy balance flow chart (Figure 1).

  10. Uniplanar microwave balanced mixers and amplifiers

    E-Print Network [OSTI]

    Hsu, Pang-Cheng

    1995-01-01T23:59:59.000Z

    The completely uniplanar broadband singly balanced diode mixers and FET amplifiers, which utilize coplanar waveguide and slot line as the main transmission lines, are presented. These mixers and amplifiers have several desirable features...

  11. False Choices: Barack Obama's Balance Rhetoric

    E-Print Network [OSTI]

    Bare, Andrew Mitchell

    2011-05-25T23:59:59.000Z

    Barack Obama's speeches have been analyzed by journalists and academic researchers from countless angles. There remains a hole in the literature, however, as few researchers have systematically noted the President's use of "balance rhetoric...

  12. Background-free balanced optical cross correlator

    DOE Patents [OSTI]

    Nejadmalayeri, Amir Hossein; Kaertner, Franz X

    2014-12-23T23:59:59.000Z

    A balanced optical cross correlator includes an optical waveguide, a first photodiode including a first n-type semiconductor and a first p-type semiconductor positioned about the optical waveguide on a first side of the optical waveguide's point of symmetry, and a second photodiode including a second n-type semiconductor and a second p-type semiconductor positioned about the optical waveguide on a second side of the optical waveguide's point of symmetry. A balanced receiver including first and second inputs is configured to produce an output current or voltage that reflects a difference in currents or voltages, originating from the first and the second photodiodes of the balanced cross correlator and fed to the first input and to the second input of the balanced receiver.

  13. Development of a generic computerized nuclear material accountability system

    SciTech Connect (OSTI)

    Cornell, M.D.; O'Leary, J.M.; McCutcheon, S.H.

    1987-01-01T23:59:59.000Z

    A computerized nuclear material accountability system (NucMAS) has been developed jointly by DuPont at Savannah River Plant (SRP) and Los Alamos National Laboratory (LANL). The SRP is faced with the goal of improving the accuracy and timeliness of nuclear material accountability. Limited manpower, funding, and time led to the decision to develop a single, generic, process-independent computer system for use throughout SRP's separations facilities, rather than traditional process-specific accountability computer systems. The NucMAS system is currently being installed in each of the material balance areas (MBAs) within SRP's separations facilities. It services the basic need for management of nuclear material inventory data to support timely, accurate, and consistent accountability reporting. Data input for NucMAS can come from any combination of manual entries and automated input, such as distributed control systems, laboratory computers, and vault surveillance systems. The system can be operated as a traditional, after-the-fact accountability system or in a near-real-time mode in situations where more timely data input is available and material control functions are desired. The granularity at which the accounting is performed is set by the MBA custodian and the level of detail at which input information is available.

  14. State of balance of the cryosphere

    E-Print Network [OSTI]

    van der Veen, Cornelis J.

    1991-12-05T23:59:59.000Z

    . But when a global forcing derived from an energy balance climate model is used, the simulations yield much better results. This suggests that variations in the global radiation balance may be very important and supports the results of Oerlemans [1986a...], who found that valley glaciers can be extremely sensitive to changes in the radiation budget. This means that the worldwide retreat of mountain glaciers may, in part, be caused by the increased concentrations of infrared-absorbing gases...

  15. Late wash cross-flow filter organic balance

    SciTech Connect (OSTI)

    Baich, M.A.

    1992-11-16T23:59:59.000Z

    A recent DOE-Savannah River review of the results and data from the Late Washing Crossflow Fitter assessment identified the fate of biphenyl as a concern in the Late Washing material balance. The concern arose because after the late washing operation only about 40% of the biphenyl remained in the irradiated precipitate and analyses of the spent wash water stream did not account for the missing biphenyl [2]. This document summarizes the results of subsequent filtration studies on the behavior and fate of all known organic precipitate feed components including biphenyl. The study employed a statistically designed material balance across a laboratory crossflow fitter. Data from two separate experiments are presented here. Results of the first study indicated no statistically significant loss of biphenyl, diphenylmercury, 0-terphenyl, diphenylamine, or aniline. Results did indicate minor losses of phenylboric acid, M-terphenyl, P-terphenyl, and a significant production of phenol, believed to be due to the way in which the experiment was performed. A second experiment demonstrated no statistically significant lose of any of the organic compounds.

  16. Modeling and Control for Balanced Timed and Weighted Event Graphs in Dioids

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Modeling and Control for Balanced Timed and Weighted Event Graphs in Dioids Bertrand Cottenceau for which some model matching control problems have been solved. In the context of manufacturing applications, the controllers obtained by these approaches have the effect of regulating material flows

  17. New velocity map and mass-balance estimate of Mertz Glacier, East Antarctica, derived from Landsat

    E-Print Network [OSTI]

    Berthier, Etienne

    streams hasbeen measured recently. Pine Island Glacier accelerated by 18 Æ2% between 1992 and 2000 (Rignot-moving glaciers. Repeat visible or near-infrared images of the same area can be used to track the displace- mentNew velocity map and mass-balance estimate of Mertz Glacier, East Antarctica, derived from Landsat

  18. Poplar plantation has the potential to alter the water balance in semiarid Inner Mongolia

    E-Print Network [OSTI]

    Chen, Jiquan

    Poplar plantation has the potential to alter the water balance in semiarid Inner Mongolia Burkhard Mongolia (IM). This evoked much concern regarding the ecological and environmental effects on areas plantation in IM may cover roughly 36­72 Â 103 km2 (Inner Mongolia News, 2006), which is equivalent to 6

  19. EC Transmission Line Materials

    SciTech Connect (OSTI)

    Bigelow, Tim S [ORNL

    2012-05-01T23:59:59.000Z

    The purpose of this document is to identify materials acceptable for use in the US ITER Project Office (USIPO)-supplied components for the ITER Electron cyclotron Heating and Current Drive (ECH&CD) transmission lines (TL), PBS-52. The source of material property information for design analysis shall be either the applicable structural code or the ITER Material Properties Handbook. In the case of conflict, the ITER Material Properties Handbook shall take precedence. Materials selection, and use, shall follow the guidelines established in the Materials Assessment Report (MAR). Materials exposed to vacuum shall conform to the ITER Vacuum Handbook. [Ref. 2] Commercial materials shall conform to the applicable standard (e.g., ASTM, JIS, DIN) for the definition of their grade, physical, chemical and electrical properties and related testing. All materials for which a suitable certification from the supplier is not available shall be tested to determine the relevant properties, as part of the procurement. A complete traceability of all the materials including welding materials shall be provided. Halogenated materials (example: insulating materials) shall be forbidden in areas served by the detritiation systems. Exceptions must be approved by the Tritium System and Safety Section Responsible Officers.

  20. UNIVERSITY OF WASHINGTON Hazardous Materials Environmental Health & Safety

    E-Print Network [OSTI]

    Wilcock, William

    UNIVERSITY OF WASHINGTON Hazardous Materials Environmental Health & Safety Design Guide Mercury used in many laboratory areas on campus. All laboratory areas and former laboratory areas should. Cleanup by a hazardous materials contractor is required before demolition or construction can begin

  1. Lecture 10. Shallow water equations and potential vorticity Geostrophy and hydrostatic balance gives us great intuition for how the ocean organizes itself, but

    E-Print Network [OSTI]

    Thompson, Andrew

    Lecture 10. Shallow water equations and potential vorticity Geostrophy and hydrostatic balance balance, which ignores vertical accelerations: p z = -0g. (104) We can then integrate this equation of the material derivative can be re-written as h t + h · (uh) = 0. (111) Equations (106) and (111

  2. Research Areas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > TheNuclear Press Releases 2014References by WebsitehomeResearch Areas

  3. Mixture balance laws for fluid flows with phase transition

    E-Print Network [OSTI]

    Helluy, Philippe

    . Cavitation: Francis turbine, cavitation damage and old repairs with stainless steel welding Mixture balance

  4. Laser detection of material thickness

    DOE Patents [OSTI]

    Early, James W. (Los Alamos, NM)

    2002-01-01T23:59:59.000Z

    There is provided a method for measuring material thickness comprising: (a) contacting a surface of a material to be measured with a high intensity short duration laser pulse at a light wavelength which heats the area of contact with the material, thereby creating an acoustical pulse within the material: (b) timing the intervals between deflections in the contacted surface caused by the reverberation of acoustical pulses between the contacted surface and the opposite surface of the material: and (c) determining the thickness of the material by calculating the proportion of the thickness of the material to the measured time intervals between deflections of the contacted surface.

  5. Evaluating the Impact of Solar Generation on Balancing Requirements in Southern Nevada System

    SciTech Connect (OSTI)

    Ma, Jian; Lu, Shuai; Etingov, Pavel V.; Makarov, Yuri V.

    2012-07-26T23:59:59.000Z

    Abstract—In this paper, the impacts of solar photovoltaic (PV) generation on balancing requirements including regulation and load following in the Southern Nevada balancing area are analyzed. The methodology is based on the “swinging door” algorithm and a probability box method developed by PNNL. The regulation and load following signals are mimicking the system’s scheduling and real-time dispatch processes. Load, solar PV generation and distributed PV generation (DG) data are used in the simulation. Different levels of solar PV generation and DG penetration profiles are used in the study. Sensitivity of the regulation requirements with respect to real-time solar PV generation forecast errors is analyzed.

  6. Nuclear Materials Management and Safeguards System Reporting and Data Submission

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1998-02-10T23:59:59.000Z

    The manual provides clear and detailed instructions and procedures for documenting and reporting data submissions for nuclear materials transactions, inventories, and material balances to the Nuclear Materials Management and Safeguards System (NMMSS). Cancels DOE 5633.3B. Canceled by DOE M 474.1-2A.

  7. Covetic Materials

    Energy Savers [EERE]

    Can re-melt, dilute, alloy... Fabrication of Covetic Materials - Nanocarbon Infusion 3 4 Technical Approach Unusual Characteristics of Covetic Materials ("covalent" &...

  8. 300 Area Disturbance Report

    SciTech Connect (OSTI)

    LL Hale; MK Wright; NA Cadoret

    1999-01-07T23:59:59.000Z

    The objective of this study was to define areas of previous disturbance in the 300 Area of the U.S. Department of Energy (DOE) Hanford Site to eliminate these areas from the cultural resource review process, reduce cultural resource monitoring costs, and allow cultural resource specialists to focus on areas where subsurface disturbance is minimal or nonexistent. Research into available sources suggests that impacts from excavations have been significant wherever the following construction activities have occurred: building basements and pits, waste ponds, burial grounds, trenches, installation of subsurface pipelines, power poles, water hydrants, and well construction. Beyond the areas just mentioned, substrates in the' 300 Area consist of a complex, multidimen- sional mosaic composed of undisturbed stratigraphy, backfill, and disturbed sediments; Four Geographic Information System (GIS) maps were created to display known areas of disturbance in the 300 Area. These maps contain information gleaned from a variety of sources, but the primary sources include the Hanford GIS database system, engineer drawings, and historic maps. In addition to these maps, several assumptions can be made about areas of disturbance in the 300 Area as a result of this study: o o Buried pipelines are not always located where they are mapped. As a result, cultural resource monitors or specialists should not depend on maps depicting subsurface pipelines for accurate locations of previous disturbance. Temporary roads built in the early 1940s were placed on layers of sand and gravel 8 to 12 in. thick. Given this information, it is likely that substrates beneath these early roads are only minimally disturbed. Building foundations ranged from concrete slabs no more than 6 to 8 in. thick to deeply excavated pits and basements. Buildings constructed with slab foundations are more numerous than may be expected, and minimally disturbed substrates may be expected in these locations. Historic black and white photographs provide a partial record of some excavations, including trenches, building basements, and material lay-down yards. Estimates of excavation depth and width can be made, but these estimates are not accurate enough to pinpoint the exact location where the disturbedhmdisturbed interface is located (e.g., camera angles were such that depths and/or widths of excavations could not be accurately determined or estimated). In spite of these limitations, these photographs provide essential information. Aerial and historic low-level photographs have captured what appears to be backfill throughout much of the eastern portion of the 300 Area-near the Columbia River shoreline. This layer of fill has likely afforded some protection for the natural landscape buried beneath the fill. This assumption fits nicely with the intermittent and inadvertent discoveries of hearths and stone tools documented through the years in this part of the 300 Area. Conversely, leveling of sand dunes appears to be substantial in the northwestern portion of the 300 Area during the early stages of development. o Project files and engineer drawings do not contain information on any impromptu but necessary adjustments made on the ground during project implementation-after the design phase. Further, many projects are planned and mapped but never implemented-this information is also not often placed in project files. Specific recommendations for a 300 Area cultural resource monitoring strategy are contained in the final section of this document. In general, it is recommended that monitoring continue for all projects located within 400 m of the Columbia River. The 400-m zone is culturally sensitive and likely retains some of the most intact buried substrates in the 300 Area.

  9. Large area bulk superconductors

    DOE Patents [OSTI]

    Miller, Dean J. (Darien, IL); Field, Michael B. (Jersey City, NJ)

    2002-01-01T23:59:59.000Z

    A bulk superconductor having a thickness of not less than about 100 microns is carried by a polycrystalline textured substrate having misorientation angles at the surface thereof not greater than about 15.degree.; the bulk superconductor may have a thickness of not less than about 100 microns and a surface area of not less than about 50 cm.sup.2. The textured substrate may have a thickness not less than about 10 microns and misorientation angles at the surface thereof not greater than about 15.degree.. Also disclosed is a process of manufacturing the bulk superconductor and the polycrystalline biaxially textured substrate material.

  10. Balance of Plant Requirements for a Nuclear Hydrogen Plant

    SciTech Connect (OSTI)

    Bradley Ward

    2006-04-01T23:59:59.000Z

    This document describes the requirements for the components and systems that support the hydrogen production portion of a 600 megawatt thermal (MWt) Next Generation Nuclear Plant (NGNP). These systems, defined as the "balance-of-plant" (BOP), are essential to operate an effective hydrogen production plant. Examples of BOP items are: heat recovery and heat rejection equipment, process material transport systems (pumps, valves, piping, etc.), control systems, safety systems, waste collection and disposal systems, maintenance and repair equipment, heating, ventilation, and air conditioning (HVAC), electrical supply and distribution, and others. The requirements in this document are applicable to the two hydrogen production processes currently under consideration in the DOE Nuclear Hydrogen Initiative. These processes are the sulfur iodide (S-I) process and the high temperature electrolysis (HTE) process. At present, the other two hydrogen production process - the hybrid sulfur-iodide electrolytic process (SE) and the calcium-bromide process (Ca-Br) -are under flow sheet development and not included in this report. While some features of the balance-of-plant requirements are common to all hydrogen production processes, some details will apply only to the specific needs of individual processes.

  11. Plutonium focus area

    SciTech Connect (OSTI)

    NONE

    1996-08-01T23:59:59.000Z

    To ensure research and development programs focus on the most pressing environmental restoration and waste management problems at the U.S. Department of Energy (DOE), the Assistant Secretary for the Office of Environmental Management (EM) established a working group in August 1993 to implement a new approach to research and technology development. As part of this new approach, EM developed a management structure and principles that led to the creation of specific Focus Areas. These organizations were designed to focus the scientific and technical talent throughout DOE and the national scientific community on the major environmental restoration and waste management problems facing DOE. The Focus Area approach provides the framework for intersite cooperation and leveraging of resources on common problems. After the original establishment of five major Focus Areas within the Office of Technology Development (EM-50, now called the Office of Science and Technology), the Nuclear Materials Stabilization Task Group (EM-66) followed the structure already in place in EM-50 and chartered the Plutonium Focus Area (PFA). The following information outlines the scope and mission of the EM, EM-60, and EM-66 organizations as related to the PFA organizational structure.

  12. Materials Scientist

    Broader source: Energy.gov [DOE]

    Alternate Title(s):Materials Research Engineer; Metallurgical/Chemical Engineer; Product Development Manager;

  13. load balancing tool for OASIS coupled systems

    E-Print Network [OSTI]

    LUCIA, load balancing tool for OASIS coupled systems Eric Maisonnave, Arnaud Caubel TR-CMGC-14-63 #12;Table of contents 1. Description of an OASIS3-MCT-based coupled system..............................................................................................14 #12;This document focuses on how to optimize performances of an OASIS3-MCT-based coupled system

  14. Which Exterior Powers are Balanced? Devlin Mallory

    E-Print Network [OSTI]

    Zaslavsky, Thomas

    Which Exterior Powers are Balanced? Devlin Mallory Department of Mathematics University conjugation by a diagonal ±1 matrix. For a signed graph on n vertices, its exterior kth power, where k = 1 onto the anti-symmetric subspace of the k-fold tensor product space (Cn)k and k is the k

  15. RESEARCH LETTERS Vibrating insoles and balance

    E-Print Network [OSTI]

    Collins, James J.

    , and such changes have been associated with diminished motor performance. Input noise can enhance sensory and motor be substantially reduced through the application of mechanical noise to the feet via vibrating insoles. We usedRESEARCH LETTERS Vibrating insoles and balance control in elderly people Attila A Priplata, James B

  16. Balanced Codon Usage Optimizes Eukaryotic Translational Efficiency

    E-Print Network [OSTI]

    Zhang, Jianzhi

    Balanced Codon Usage Optimizes Eukaryotic Translational Efficiency Wenfeng Qian1 , Jian-Rong Yang1, Guangzhou, China Abstract Cellular efficiency in protein translation is an important fitness determinant and that translational efficiency is maximized by the exclusive use of rapidly translated codons. Here we estimate

  17. IntroductiontoProcessEngineering(PTG) conversion, balances,

    E-Print Network [OSTI]

    Zevenhoven, Ron

    #3/6 IntroductiontoProcessEngineering(PTG) VST rz13 1/118 3. Energy conversion, balances rz13 2/118 3.1: Energy #12;#3/6 IntroductiontoProcessEngineering(PTG) VST rz13 3/118 What is energy? · "Energy is any quantity that changes the state of a closed system when crossing the system boundary" (SEHB

  18. Bioenergy technology balancing energy output with environmental

    E-Print Network [OSTI]

    Levi, Ran

    E2.3 Bioenergy technology ­ balancing energy output with environmental benefitsbenefits John bioenergy Farmers historically used 25% land for horse feed #12;Energy crops are `solar panels' Solar energy° 50° #12;Same climate data (A1F1 scenario for 2050 - 2080) but the genotype is one which is less

  19. Uniplanar microwave balanced mixers and amplifiers 

    E-Print Network [OSTI]

    Hsu, Pang-Cheng

    1995-01-01T23:59:59.000Z

    (MMICs). Two new types of uniplanar broadband singly balanced diode mixers are developed. The first mixer exhibits a conversion loss between 6 and 10 dB when the RF is swept from 7 to 10.5 GHz and the LO is 3.5 dBm fixed at 7 GHz. The measured IP3...

  20. Hazardous Materials Alert Departmental Contact(s)

    E-Print Network [OSTI]

    Hickman, Mark

    Hazardous Materials Alert Departmental Contact(s): Name ___________________________________________________________________________________ Hazardous Materials Alert If the release of a hazardous chemical or gas is affecting people in your area yourself at risk. 2. isOlATE the hazardous material by clearing the area, close the doors. If safe to do so

  1. Mathematical model of the Lame' Problem for Simplified Elastic Theory applied to Controlled-Clearance Pressure Balances

    E-Print Network [OSTI]

    Saragosa Silvano

    2012-02-18T23:59:59.000Z

    In order to obtain more accurate measurements, the use of pressure balances with the controlled-clearance system is well known in the history of high pressures metrology. Furthermore, the introduction of assemblies with cylinders made up of two materials to the construction of controlled-clearance pressure balances, is one of the most important developments in the field of high pressure measurements. The use of some analytical procedures for the characterization of the pressure balances (also known as piston gauges) becomes more difficult especially for the case of geometries with composite cylinders. Those geometries were also studied with the analytical method developed by the author[1] (based on a simplified model) and described in this paper. This method was also reported in some not original publications from 2003 to 2007. The analysis begins with the mathematical model of thick-walled cylinder applied to the Mechanical theory of elastic equilibrium for the formulation of the so called Simplified Elastic Theory which represents an analytical approach for the study of pressure balances. This analysis is known as the Lame' problem. The solution of the Lame' Problem is used to determine the pressure distortion coefficient for the controlled-clearance pressure balances including the case of pressure balances with the cylinder made up of two materials.

  2. The balancing market maker: a tool to enhance liquidity in the French balancing mechanism

    SciTech Connect (OSTI)

    Batlle, Carlos; Vazquez, Carlos; Barquin, Julian

    2007-07-15T23:59:59.000Z

    The development of a more competition-oriented and less concentrated market structure in France is colliding with the functioning of the balancing market. The authors offer a proposal to improve the balancing market system, with a view to achieving a more flexible, transparent, and competitive structure, which in turn should lead to more efficient and cheaper service, without compromising the bedrock need to maintain system security. (author)

  3. Analyzing of Balancing Authorities Cooperation Methods with High Variable Generation Penetration

    SciTech Connect (OSTI)

    Makarov, Yuri V.; Zhou, Ning; Etingov, Pavel V.; Samaan, Nader A.; Ma, Jian; Diao, Ruisheng; Guttromson, Ross T.

    2010-11-02T23:59:59.000Z

    With the rapidly growing penetration level of wind and solar generation, the challenges of managing variability and the uncertainty of intermittent renewable generation become more and more significant. The problem of power variability and uncertainty gets exacerbated when each balancing authority (BA) works locally and separately to balance its own subsystem. The virtual BA concept is based on various forms of collaboration between individual BAs to manage power variability and uncertainty. The virtual BA will have a wide area control capability in managing its operational balancing requirements in different time frames. This coordination results in the improvement of efficiency and reliability of power system operation while facilitating the high level integration of green, intermittent energy resources. Several strategies for virtual BA implementation, such as Area Control Error (ACE) diversity interchange (ADI), variable generation only BA, BA consolidation, dynamic scheduling, and regulation and load following sharing are discussed in this paper. The objective of such strategies is to allow individual BAs within a large power grid to help each other dealing with power variability. Innovative methods have been developed to simulate the balancing operation of BAs. These methods evaluate the BA operation through a number of metrics such as capacity, ramp rate, ramp duration, energy and cycling requirements to evaluate the performance of different virtual BA strategies.

  4. Evaluation of a spatially-distributed Thornthwaite water-balance model

    SciTech Connect (OSTI)

    Lough, J.A. (Univ. of New Hampshire, Durham, NH (United States). Complex Systems Research Center)

    1993-03-01T23:59:59.000Z

    A small watershed of low relief in coastal New Hampshire was divided into hydrologic sub-areas in a geographic information system on the basis of soils, sub-basins and remotely-sensed landcover. Three variables were spatially modeled for input to 49 individual water-balances: available water content of the root zone, water input and potential evapotranspiration (PET). The individual balances were weight-summed to generate the aggregate watershed-balance, which saw 9% (48--50 mm) less annual actual-evapotranspiration (AET) compared to a lumped approach. Analysis of streamflow coefficients suggests that the spatially-distributed approach is more representative of the basin dynamics. Variation of PET by landcover accounted for the majority of the 9% AET reduction. Variation of soils played a near-negligible role. As a consequence of the above points, estimates of landcover proportions and annual PET by landcover are sufficient to correct a lumped water-balance in the Northeast. If remote sensing is used to estimate the landcover area, a sensor with a high spatial resolution is required. Finally, while the lower Thornthwaite model has conceptual limitations for distributed application, the upper Thornthwaite model is highly adaptable to distributed problems and may prove useful in many earth-system models.

  5. Action Plan Materials Science

    E-Print Network [OSTI]

    Fitze, Patrick

    sense, including all strata) has available to it a wide range of con- venient products which improve, improving companies' pros- pects and generating wealth without harming the environment. And allAction Plan 2010-2013 Materials Science Area EXECUTIVE SUMMARY #12;N.B.: If you require any further

  6. Benefit of Regional Energy Balancing Service on Wind Integration in the Western Interconnection of the United States

    SciTech Connect (OSTI)

    Milligan, M.; Kirby, B.; King, J.; Beuning, S.

    2010-01-01T23:59:59.000Z

    Interest in various wide-area balancing schemes to help integrate wind have generated significant interest. As we have shown in past work, large balancing areas not only help with wind integration, but can also increase the efficiency of operations in systems without wind. Recent work on the Western Wind and Solar Integration Study (WWSIS) has found that combining balancing over the WestConnect footprint will increase the efficiency of commitment and dispatch at wind penetrations ranging from 10-20% of annual electricity demand, and will be essential for high penetrations and small balancing areas. In addition the Northwest Wind Integration Action Plan recommended balancing area cooperation as a method to help integrate the large potential wind development. In this paper we investigate the potential impact of a proposed Energy Imbalance Service on the ability of the non-market portions of Western Electricity Coordinating Councils (WECC) United States footprint to integrate wind energy. We will utilize data adapted from the WWSIS for the Western Interconnection. The analysis uses time-synchronized wind and load data to evaluate the potential for ramp requirement reduction that could be achieved with combined operation. Chronological analysis and ramp duration analysis quantify the benefit in terms of not only the ramp sizes, but the frequency of the potentially avoided ramps that must be managed by the non-wind generation fleet. Multiple approaches that can be used to achieve these benefits will also be suggested in the paper. We also suggest other approaches that can help achieve much of the benefit of full consolidation without requiring the physical consolidation of balancing areas.

  7. ANALYSIS OF POWER BALANCING WITH FUEL CELLS & HYDROGEN

    E-Print Network [OSTI]

    ANALYSIS OF POWER BALANCING WITH FUEL CELLS & HYDROGEN PRODUCTION PLANTS IN DENMARK Support program;"Analysis of power balancing with fuel cells & hydrogen production plants in Denmark" ­ March 2009 ­ Project-TO-TANK..........................................................................................................26 C.1 Hydrogen production from electrolysis

  8. First law energy balance as a data screening tool 

    E-Print Network [OSTI]

    Shao, Xiaojie

    2006-08-16T23:59:59.000Z

    This thesis defines the Energy Balance Load ( BL E ) as the difference between the heating requirements plus the electric gains in the building and the cooling coil loads. It then applies a first law energy balance in ...

  9. The Computational Materials and Chemical Sciences Network (CMCSN...

    Office of Science (SC) Website

    The Computational Materials and Chemical Sciences Network (CMCSN) Materials Sciences and Engineering (MSE) Division MSE Home About Research Areas Energy Frontier Research Centers...

  10. advanced materials technology: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    hiring areas are: Novel Sustainable Materials Alpay, S. Pamir 3 ADVANCED COMPOSITE MATERIALS TECHNOLOGY FOR ROTORCRAFT Andrew Makeev*, University of Texas at Arlington,...

  11. advanced technological materials: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    hiring areas are: Novel Sustainable Materials Alpay, S. Pamir 3 ADVANCED COMPOSITE MATERIALS TECHNOLOGY FOR ROTORCRAFT Andrew Makeev*, University of Texas at Arlington,...

  12. Nuclear Dynamics at the Balance Energy

    E-Print Network [OSTI]

    Aman D. Sood; Rajeev K. Puri

    2003-11-05T23:59:59.000Z

    We study the mass dependence of various quantities (like the average and maximum density, collision rate, participant-spectator matter, temperature as well as time zones for higher density) by simulating the reactions at the energy of vanishing flow. This study is carried out within the framework of Quantum Molecular Dynamics model. Our findings clearly indicate an existence of a power law in all the above quantities calculated at the balance energy. The only significant mass dependence was obtained for the temperature reached in the central sphere. All other quantities are rather either insensitive or depend weakly on the system size at balance energy. The time zone for higher density as well as the time of maximal density and collision rate follow a power law inverse to the energy of vanishing flow.

  13. Nigerian refineries strive for product balance

    SciTech Connect (OSTI)

    Obuasi, P.A.

    1985-06-17T23:59:59.000Z

    This article discusses the growth patterns of the Nigerian refining industry. Production and consumption are expected to follow the pattern of consumption of fuel products by the domestic market, Presently, however, production and consumption are not evenly balanced for most fuel products, and non-fuel products are domestically consumed but not produced. Some progress has been made in the effort to match production and consumption of fuel products. But the progress that would have been made to balance non-fuel products has been nullified by 50% of the Daduna refinery being idle. This is due to problems associated with importation of heavy crude oil into Nigeria and also a weak market for asphalt in Nigeria.

  14. Low-Level waste phase 1 melter testing off gas and mass balance evaluation

    SciTech Connect (OSTI)

    Wilson, C.N.

    1996-06-28T23:59:59.000Z

    Commercially available melter technologies were tested during 1994-95 as part of a multiphase program to test candidate technologies for vitrification of the low-level waste (LLW) stream to be derived from retrieval and pretreatment of Hanford Site tank wastes. Seven vendors were selected for Phase 1 testing to demonstrate vitrification of a high sodium content liquid LLW simulant. The tested melter technologies included four Joule-heated melters, a carbon electrode melter, a combustion melter, and a plasma melter. Various dry and slurry melter feed preparation processes were also tested. Various feed material samples, product glass samples, and process offgas streams were characterized to provide data for evaluation of process decontamination factors and material mass balances for each vitrification technology. This report describes the melter mass balance evaluations and results for six of the Phase 1 LLW melter vendor demonstration tests.

  15. Optimized nanoporous materials.

    SciTech Connect (OSTI)

    Braun, Paul V. (University of Illinois at Urbana-Champaign, Urbana, IL); Langham, Mary Elizabeth; Jacobs, Benjamin W.; Ong, Markus D.; Narayan, Roger J. (North Carolina State University, Raleigh, NC); Pierson, Bonnie E. (North Carolina State University, Raleigh, NC); Gittard, Shaun D. (North Carolina State University, Raleigh, NC); Robinson, David B.; Ham, Sung-Kyoung (Korea Basic Science Institute, Gangneung, South Korea); Chae, Weon-Sik (Korea Basic Science Institute, Gangneung, South Korea); Gough, Dara V. (University of Illinois at Urbana-Champaign, Urbana, IL); Wu, Chung-An Max; Ha, Cindy M.; Tran, Kim L.

    2009-09-01T23:59:59.000Z

    Nanoporous materials have maximum practical surface areas for electrical charge storage; every point in an electrode is within a few atoms of an interface at which charge can be stored. Metal-electrolyte interfaces make best use of surface area in porous materials. However, ion transport through long, narrow pores is slow. We seek to understand and optimize the tradeoff between capacity and transport. Modeling and measurements of nanoporous gold electrodes has allowed us to determine design principles, including the fact that these materials can deplete salt from the electrolyte, increasing resistance. We have developed fabrication techniques to demonstrate architectures inspired by these principles that may overcome identified obstacles. A key concept is that electrodes should be as close together as possible; this is likely to involve an interpenetrating pore structure. However, this may prove extremely challenging to fabricate at the finest scales; a hierarchically porous structure can be a worthy compromise.

  16. Traffic Dynamics Prospectives: From Fundamental Diagram to Energy Balance

    E-Print Network [OSTI]

    Bertini, Robert L.

    Traffic Dynamics Prospectives: From Fundamental Diagram to Energy Balance R. Mahnke1 , Ch. Liebe, R) = vmax D m 2 - arctan xi D (13) Energy balance: d dt (Ekin(vi) + Epot(xi)) + i(xi, vi, vi+1) = 0 (14) with i as energy flux. 08.07.2008 Woods Hole ­ p.8/11 #12;Energy Balance with Energy Flux Energy balance

  17. 3-D Force-balanced Magnetospheric Configurations

    SciTech Connect (OSTI)

    Sorin Zaharia; C.Z. Cheng; K. Maezawa

    2003-02-10T23:59:59.000Z

    The knowledge of plasma pressure is essential for many physics applications in the magnetosphere, such as computing magnetospheric currents and deriving magnetosphere-ionosphere coupling. A thorough knowledge of the 3-D pressure distribution has however eluded the community, as most in-situ pressure observations are either in the ionosphere or the equatorial region of the magnetosphere. With the assumption of pressure isotropy there have been attempts to obtain the pressure at different locations by either (a) mapping observed data (e.g., in the ionosphere) along the field lines of an empirical magnetospheric field model or (b) computing a pressure profile in the equatorial plane (in 2-D) or along the Sun-Earth axis (in 1-D) that is in force balance with the magnetic stresses of an empirical model. However, the pressure distributions obtained through these methods are not in force balance with the empirical magnetic field at all locations. In order to find a global 3-D plasma pressure distribution in force balance with the magnetospheric magnetic field, we have developed the MAG-3D code, that solves the 3-D force balance equation J x B = (upside-down delta) P computationally. Our calculation is performed in a flux coordinate system in which the magnetic field is expressed in terms of Euler potentials as B = (upside-down delta) psi x (upside-down delta) alpha. The pressure distribution, P = P(psi,alpha), is prescribed in the equatorial plane and is based on satellite measurements. In addition, computational boundary conditions for y surfaces are imposed using empirical field models. Our results provide 3-D distributions of magnetic field and plasma pressure as well as parallel and transverse currents for both quiet-time and disturbed magnetospheric conditions.

  18. Energy-momentum balance in quantum dielectrics

    E-Print Network [OSTI]

    Ulf Leonhardt

    2005-12-21T23:59:59.000Z

    We calculate the energy-momentum balance in quantum dielectrics such as Bose-Einstein condensates. In agreement with the experiment [G. K. Campbell et al. Phys. Rev. Lett. 94, 170403 (2005)] variations of the Minkowski momentum are imprinted onto the phase, whereas the Abraham tensor drives the flow of the dielectric. Our analysis indicates that the Abraham-Minkowski controversy has its root in the Roentgen interaction of the electromagnetic field in dielectric media.

  19. Energy Balance and Emissions Associated with Biochar

    E-Print Network [OSTI]

    Lehmann, Johannes

    to produce biochar for land application, the energy produced per unit energy input at 2­7 MJ/MJ is greaterEnergy Balance and Emissions Associated with Biochar Sequestration and Pyrolysis Bioenergy Production J O H N L . G A U N T * , , A N D J O H A N N E S L E H M A N N College of Agriculture and Life

  20. Surface Meteorology, Barrow, Alaska, Area A, B, C and D, Ongoing from 2012

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Hinzman, Larry; Busey, Bob; Cable, William; Romanovsky, Vladimir

    Meteorological data are being collected at several points within four intensive study areas in Barrow. These data assist in the calculation of the energy balance at the land surface and are also useful as inputs into modeling activities.

  1. Surface Meteorology, Barrow, Alaska, Area A, B, C and D, Ongoing from 2012

    SciTech Connect (OSTI)

    Hinzman, Larry; Busey, Bob; Cable, William; Romanovsky, Vladimir

    2014-12-04T23:59:59.000Z

    Meteorological data are being collected at several points within four intensive study areas in Barrow. These data assist in the calculation of the energy balance at the land surface and are also useful as inputs into modeling activities.

  2. China's terrestrial carbon balance: Contributions from multiple global change factors

    E-Print Network [OSTI]

    Montana, University of

    China's terrestrial carbon balance: Contributions from multiple global change factors Hanqin Tian,1 to be investigated. China is important in determining the global carbon balance in terms of both carbon emission change) on net carbon balance in terrestrial ecosystems of China for the period 1961­2005 were modeled

  3. Parameter estimation for energy balance models with memory

    E-Print Network [OSTI]

    Parameter estimation for energy balance models with memory By Lionel Roques1,*, Micka¨el D parameter estimation for one-dimensional energy balance models with mem- ory (EBMMs) given localized estimate is still possible in certain cases. Keywords: age dating; Bayesian inference; energy balance model

  4. Spatial Energy Balancing in Large-scale Wireless Multihop Networks

    E-Print Network [OSTI]

    de Veciana, Gustavo

    Spatial Energy Balancing in Large-scale Wireless Multihop Networks Seung Jun Baek and Gustavo de is on optimizing trade-offs between the energy cost of spreading traffic and the improved spatial balance of energy. We propose a parameterized family of energy balancing strategies for grids and approximate

  5. Canopy radiation transmission for an energy balance snowmelt model

    E-Print Network [OSTI]

    Tarboton, David

    Canopy radiation transmission for an energy balance snowmelt model Vinod Mahat1 and David G deep canopy solution. This solution enhances capability for modeling energy balance processes in a distributed energy balance snowmelt model and results compared with observations made in three different

  6. 12. Energy balance of particles 12.1 General solutions

    E-Print Network [OSTI]

    Pohl, Martin Karl Wilhelm

    12. Energy balance of particles 12.1 General solutions In this chapter we want to study only to consider the heating/cooling balance of the temperature as a parameter of a known energy distribution by the balance of effects that depend on the particle energy. We can write down a continuity equation

  7. Version 3.0 January 2013 Nutrient Balance Sheet

    E-Print Network [OSTI]

    Guiltinan, Mark

    Version 3.0 ­ January 2013 Nutrient Balance Sheet Prepared For Operator's Name Operator's Address for each crop management unit (if applicable) #12;Version 3.0 ­ January 2013 Nutrient Balance Sheet Summary = nutrient excess #12;Version 3.0 ­ January 2013 Nutrient Balance Sheet Summary Notes CMU/Field ID Crop Group

  8. Development of Balancing Markets in the West Status Report

    E-Print Network [OSTI]

    Development of Balancing Markets in the West ­ Status Report Wally Gibson Power Committee Missoula, Montana January 11, 2011 #12;January 11, 2011 2 Overview · Why balancing markets? · Related 6th Power Plan · Balancing is particularly a problem now for BAs with large amounts of wind, e.g., BPA · What can be done

  9. Lifetime Benefits through Load Balancing in Homogeneous Sensor Networks

    E-Print Network [OSTI]

    Haenggi, Martin

    , battery depletion is emulated so that it becomes possible to actually measure the load balancingLifetime Benefits through Load Balancing in Homogeneous Sensor Networks Daniele Puccinelli network. The use of load balancing schemes can be expected to provide significant lifetime benefits

  10. Systems Engineering of Chemical Hydrogen Storage, Pressure Vessel and Balance of Plant for Onboard Hydrogen Storage

    SciTech Connect (OSTI)

    Brooks, Kriston P.; Simmons, Kevin L.; Weimar, Mark R.

    2014-09-02T23:59:59.000Z

    This is the annual report for the Hydrogen Storage Engineering Center of Excellence project as required by DOE EERE's Fuel Cell Technologies Office. We have been provided with a specific format. It describes the work that was done with cryo-sorbent based and chemical-based hydrogen storage materials. Balance of plant components were developed, proof-of-concept testing performed, system costs estimated, and transient models validated as part of this work.

  11. Multiobjective calibration and sensitivity of a distributed land surface water and energy balance model

    E-Print Network [OSTI]

    Houser, Paul R; Gupta, Hoshin V; Shuttleworth, W. James; Famiglietti, James S

    2001-01-01T23:59:59.000Z

    identification and energy balance models on a tallgrassdata for surface energy balance evaluation of a semiaridWatershed. We are energy balance components over a semiarid

  12. Surface Energy Balance Measurements Above an Exurban Residential Neighbourhood of Kansas City, Missouri

    E-Print Network [OSTI]

    Balogun, Ahmed A.; Adegoke, Jimmy O.; Vezhapparambu, Sajith; Mauder, Matthias; McFadden, Joseph P.; Gallo, Kevin

    2009-01-01T23:59:59.000Z

    9421-3 ARTICLE Surface Energy Balance Measurements Above anmeasurements of urban energy balances generally have beenuxes · Urban surface energy balance 1 Introduction Rapid

  13. Towards a Sustainable Energy Balance: Progressive Efficiency and the Return of Energy Conservation

    E-Print Network [OSTI]

    Harris, Jeff

    2008-01-01T23:59:59.000Z

    words, the sustainable energy balance serves as a goal forthe sustainable energy balance would mean a renewable energythe goal of a sustainable energy balance. Figure 2 shows how

  14. Towards a Sustainable Energy Balance: Progressive Efficiency and the Return of Energy Conservation

    E-Print Network [OSTI]

    Harris, Jeffrey; Diamond, Rick; Iyer, Maithili; Payne, Christopher; Blumstein, Carl; Siderius, Hans-Paul

    2007-01-01T23:59:59.000Z

    Towards a Sustainable Energy Balance: Progressive EfficiencyTowards a Sustainable Energy Balance: Progressive Efficiencyachieve a sustainable energy balance. Along the way, we may

  15. Towards a Sustainable Energy Balance: Progressive Efficiency and the Return of Energy Conservation

    E-Print Network [OSTI]

    Harris, Jeffrey; Diamond, Rick; Iyer, Maithili; Payne, Christopher; Blumstein, Carl; Siderius, Hans-Paul

    2007-01-01T23:59:59.000Z

    WP 171 Towards a Sustainable Energy Balance: ProgressiveTowards a Sustainable Energy Balance: Progressive Efficiencyin order to achieve a sustainable energy balance. Along the

  16. Towards a Sustainable Energy Balance: Progressive Efficiency and the Return of Energy Conservation

    E-Print Network [OSTI]

    Harris, Jeff

    2008-01-01T23:59:59.000Z

    Towards a Sustainable Energy Balance: Progressive Efficiencyin order to achieve a sustainable energy balance. Along theconsumer desires. 1.2 Sustainable Energy Balance as the Goal

  17. MULTISCALE PHENOMENA IN MATERIALS

    SciTech Connect (OSTI)

    A. BISHOP

    2000-09-01T23:59:59.000Z

    This project developed and supported a technology base in nonequilibrium phenomena underpinning fundamental issues in condensed matter and materials science, and applied this technology to selected problems. In this way the increasingly sophisticated synthesis and characterization available for classes of complex electronic and structural materials provided a testbed for nonlinear science, while nonlinear and nonequilibrium techniques helped advance our understanding of the scientific principles underlying the control of material microstructure, their evolution, fundamental to macroscopic functionalities. The project focused on overlapping areas of emerging thrusts and programs in the Los Alamos materials community for which nonlinear and nonequilibrium approaches will have decisive roles and where productive teamwork among elements of modeling, simulations, synthesis, characterization and applications could be anticipated--particularly multiscale and nonequilibrium phenomena, and complex matter in and between fields of soft, hard and biomimetic materials. Principal topics were: (i) Complex organic and inorganic electronic materials, including hard, soft and biomimetic materials, self-assembly processes and photophysics; (ii) Microstructure and evolution in multiscale and hierarchical materials, including dynamic fracture and friction, dislocation and large-scale deformation, metastability, and inhomogeneity; and (iii) Equilibrium and nonequilibrium phases and phase transformations, emphasizing competing interactions, frustration, landscapes, glassy and stochastic dynamics, and energy focusing.

  18. Site Monitoring Area Maps

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to the Site Monitoring Area (SMA) The Site Monitoring Area sampler Control measures (best management practices) installed at the Site Monitoring Area Structures such as...

  19. Wildlife Management Areas (Minnesota)

    Broader source: Energy.gov [DOE]

    Certain areas of the State are designated as wildlife protection areas and refuges; new construction and development is restricted in these areas.

  20. Advanced Reflector and Absorber Materials (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-08-01T23:59:59.000Z

    Fact sheet describing NREL CSP Program capabilities in the area of advanced reflector and absorber materials: evaluating performance, determining degradation rates and lifetime, and developing new coatings.

  1. Chemistry and materials science progress report, FY 1994

    SciTech Connect (OSTI)

    NONE

    1995-07-01T23:59:59.000Z

    Research is reported in the areas of surface science, fundamentals of the physics and processing of metals, energetic materials, transactinide materials and properties and other indirectly related areas of weapons research.

  2. Mass balances for underground coal gasification in steeply dipping beds

    SciTech Connect (OSTI)

    Lindeman, R.; Ahner, P.; Davis, B.E.

    1980-01-01T23:59:59.000Z

    Two different mass balances were used during the recent underground coal gasification tests conducted in steeply dipping coal beds at Rawlins, Wyoming. The combination of both mass balances proved extremely useful in interpreting the test results. One mass balance which assumed char could be formed underground required the solution of 3 simultaneous equations. The assumption of no char decouples the 3 equations in the other mass balance. Both mass balance results are compared to the test data to provide an interpretation of the underground process.

  3. Supplementary Material for Particle Mass Yield from -Caryophyllene Ozonolysis

    E-Print Network [OSTI]

    Meskhidze, Nicholas

    of the measurements, based on solving the heat balance equation in the frequency domain, will be presented of Engineering, Cardiff University Title: Impedance spectroscopy methods applied to thermoelectric materials for thermoelectric devices and materials. Additionally, he is also involved in the characterisation of dye

  4. Potentials and policy implications of energy and material efficiency improvement

    SciTech Connect (OSTI)

    Worrell, Ernst; Levine, Mark; Price, Lynn; Martin, Nathan; van den Broek, Richard; Block, Kornelis

    1997-01-01T23:59:59.000Z

    There is a growing awareness of the serious problems associated with the provision of sufficient energy to meet human needs and to fuel economic growth world-wide. This has pointed to the need for energy and material efficiency, which would reduce air, water and thermal pollution, as well as waste production. Increasing energy and material efficiency also have the benefits of increased employment, improved balance of imports and exports, increased security of energy supply, and adopting environmentally advantageous energy supply. A large potential exists for energy savings through energy and material efficiency improvements. Technologies are not now, nor will they be, in the foreseeable future, the limiting factors with regard to continuing energy efficiency improvements. There are serious barriers to energy efficiency improvement, including unwillingness to invest, lack of available and accessible information, economic disincentives and organizational barriers. A wide range of policy instruments, as well as innovative approaches have been tried in some countries in order to achieve the desired energy efficiency approaches. These include: regulation and guidelines; economic instruments and incentives; voluntary agreements and actions, information, education and training; and research, development and demonstration. An area that requires particular attention is that of improved international co-operation to develop policy instruments and technologies to meet the needs of developing countries. Material efficiency has not received the attention that it deserves. Consequently, there is a dearth of data on the qualities and quantities for final consumption, thus, making it difficult to formulate policies. Available data, however, suggest that there is a large potential for improved use of many materials in industrialized countries.

  5. Wildlife Management Areas (Florida)

    Broader source: Energy.gov [DOE]

    Certain sites in Florida are designated as wildlife management areas, and construction and development is heavily restricted in these areas.

  6. Critical Materials:

    Broader source: Energy.gov (indexed) [DOE]

    lighting. 14 (bottom) Criticality ratings of shortlisted raw 76 materials. 15 77 2. Technology Assessment and Potential 78 This section reviews the major trends within...

  7. Voltage balanced multilevel voltage source converter system

    DOE Patents [OSTI]

    Peng, F.Z.; Lai, J.S.

    1997-07-01T23:59:59.000Z

    Disclosed is a voltage balanced multilevel converter for high power AC applications such as adjustable speed motor drives and back-to-back DC intertie of adjacent power systems. This converter provides a multilevel rectifier, a multilevel inverter, and a DC link between the rectifier and the inverter allowing voltage balancing between each of the voltage levels within the multilevel converter. The rectifier is equipped with at least one phase leg and a source input node for each of the phases. The rectifier is further equipped with a plurality of rectifier DC output nodes. The inverter is equipped with at least one phase leg and a load output node for each of the phases. The inverter is further equipped with a plurality of inverter DC input nodes. The DC link is equipped with a plurality of rectifier charging means and a plurality of inverter discharging means. The plurality of rectifier charging means are connected in series with one of the rectifier charging means disposed between and connected in an operable relationship with each adjacent pair of rectifier DC output nodes. The plurality of inverter discharging means are connected in series with one of the inverter discharging means disposed between and connected in an operable relationship with each adjacent pair of inverter DC input nodes. Each of said rectifier DC output nodes are individually electrically connected to the respective inverter DC input nodes. By this means, each of the rectifier DC output nodes and each of the inverter DC input nodes are voltage balanced by the respective charging and discharging of the rectifier charging means and the inverter discharging means. 15 figs.

  8. Reflective optical imaging systems with balanced distortion

    DOE Patents [OSTI]

    Hudyma, Russell M. (San Ramon, CA)

    2001-01-01T23:59:59.000Z

    Optical systems compatible with extreme ultraviolet radiation comprising four reflective elements for projecting a mask image onto a substrate are described. The four optical elements comprise, in order from object to image, convex, concave, convex and concave mirrors. The optical systems are particularly suited for step and scan lithography methods. The invention enables the use of larger slit dimensions associated with ring field scanning optics, improves wafer throughput, and allows higher semiconductor device density. The inventive optical systems are characterized by reduced dynamic distortion because the static distortion is balanced across the slit width.

  9. Reflective optical imaging system with balanced distortion

    DOE Patents [OSTI]

    Chapman, Henry N. (Sunol, CA); Hudyma, Russell M. (San Ramon, CA); Shafer, David R. (Fairfield, CT); Sweeney, Donald W. (San Ramon, CA)

    1999-01-01T23:59:59.000Z

    An optical system compatible with short wavelength (extreme ultraviolet) An optical system compatible with short wavelength (extreme ultraviolet) radiation comprising four reflective elements for projecting a mask image onto a substrate. The four optical elements comprise, in order from object to image, convex, concave, convex and concave mirrors. The optical system is particularly suited for step and scan lithography methods. The invention enables the use of larger slit dimensions associated with ring field scanning optics, improves wafer throughput and allows higher semiconductor device density. The inventive optical system is characterized by reduced dynamic distortion because the static distortion is balanced across the slit width.

  10. Energy Balance Bowen Ratio Station (EBBR) Handbook

    SciTech Connect (OSTI)

    Cook, DR

    2011-02-23T23:59:59.000Z

    The energy balance Bowen ratio (EBBR) system produces 30-minute estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity (RH). Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors from instrument offset drift.

  11. Festival de Teatro de La Habana: Balance

    E-Print Network [OSTI]

    Espinosa Domí nguez, Carlos

    1982-04-01T23:59:59.000Z

    corrientes y estilos. 66 LATIN AMERICAN THEATRE REVIEW Es de notar asimismo la preferencia por los temas actuales. Diecisiete títu los de los que se vieron se inscriben en esa línea, lo cual está en relación di recta con las exigencias de un público que... labor desarrollada por los artistas cubanos en estos últimos dos años. En tal sentido, a partir de los montajes que en el mismo se pusieron puede realizarse un balance crítico de los caminos y corrientes que confluyen hoy en este movimiento. En su...

  12. Balanced Scorecard Archive | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office511041cloth DocumentationProductsAlternativeOperationalAugustDecade5-F,INITIAL JohnE P T0 InvestorBalanced

  13. Balanced Scorecard Program | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you want toworldPower 2010 1AAcquisition » Balanced Scorecard Program

  14. The United States Plutonium Balance, 1944 - 2009

    National Nuclear Security Administration (NNSA)

    owned by the DOE. Inventory refers to the plutonium maintained under nuclear material control and accountability, whereas waste estimates refer to plutonium tracked solely for...

  15. Cermet materials

    DOE Patents [OSTI]

    Kong, Peter C. (Idaho Falls, ID)

    2008-12-23T23:59:59.000Z

    A self-cleaning porous cermet material, filter and system utilizing the same may be used in filtering particulate and gaseous pollutants from internal combustion engines having intermetallic and ceramic phases. The porous cermet filter may be made from a transition metal aluminide phase and an alumina phase. Filler materials may be added to increase the porosity or tailor the catalytic properties of the cermet material. Additionally, the cermet material may be reinforced with fibers or screens. The porous filter may also be electrically conductive so that a current may be passed therethrough to heat the filter during use. Further, a heating element may be incorporated into the porous cermet filter during manufacture. This heating element can be coated with a ceramic material to electrically insulate the heating element. An external heating element may also be provided to heat the cermet filter during use.

  16. Composite material

    DOE Patents [OSTI]

    Hutchens, Stacy A. (Knoxville, TN); Woodward, Jonathan (Solihull, GB); Evans, Barbara R. (Oak Ridge, TN); O'Neill, Hugh M. (Knoxville, TN)

    2012-02-07T23:59:59.000Z

    A composite biocompatible hydrogel material includes a porous polymer matrix, the polymer matrix including a plurality of pores and providing a Young's modulus of at least 10 GPa. A calcium comprising salt is disposed in at least some of the pores. The porous polymer matrix can comprise cellulose, including bacterial cellulose. The composite can be used as a bone graft material. A method of tissue repair within the body of animals includes the steps of providing a composite biocompatible hydrogel material including a porous polymer matrix, the polymer matrix including a plurality of pores and providing a Young's modulus of at least 10 GPa, and inserting the hydrogel material into cartilage or bone tissue of an animal, wherein the hydrogel material supports cell colonization in vitro for autologous cell seeding.

  17. School of Materials Science and Engineering Program Guide

    E-Print Network [OSTI]

    New South Wales, University of

    of the materials engineer range from materials production, including their extraction from ores and their refining in minerals, materials science has been designated as a priority area for research and development. Examples

  18. Real-Time Electricity Markets Material from this introduction was adapted from [1].

    E-Print Network [OSTI]

    McCalley, James D.

    ), or balancing market. #12;2 A third market, called the operating reserve market, addresses ancillary services of products: Energy: based on resource offers and demand bids Regulating reserve: for real-time balancing1 Real-Time Electricity Markets Material from this introduction was adapted from [1

  19. area factor determinations: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: 20 North Adit North Damping Ring Radioactive Material Storage Yard (RAMSY) Radioactive Waste Storage A (includes fenced RAM storage area) End Station B Heavy...

  20. area influence caracterizacao: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: 20 North Adit North Damping Ring Radioactive Material Storage Yard (RAMSY) Radioactive Waste Storage A (includes fenced RAM storage area) End Station B Heavy...

  1. area specific studies: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: 20 North Adit North Damping Ring Radioactive Material Storage Yard (RAMSY) Radioactive Waste Storage A (includes fenced RAM storage area) End Station B Heavy...

  2. Good health is about balancing life in all areas. Here are some tips for encouraging and

    E-Print Network [OSTI]

    Rose, Michael R.

    service offers students healthy menu options. n Relaxation Relaxation decreases metabolic heart rate.uci.edu/services/safety_escorts.html Safety Mental & Physical Wellness Crisis & Stress Dispute Resolution UC Irvine Campus ResouRCes Help 824-5301 501 Student Health www.shc.uci.edu Crisis response help, information, referral on sexual

  3. Material Symbols 

    E-Print Network [OSTI]

    Clark, Andy

    2006-01-01T23:59:59.000Z

    What is the relation between the material, conventional symbol structures that we encounter in the spoken and written word, and human thought? A common assumption, that structures a wide variety of otherwise competing ...

  4. Complex Materials

    ScienceCinema (OSTI)

    Cooper, Valentino

    2014-05-23T23:59:59.000Z

    Valentino Cooper uses some of the world's most powerful computing to understand how materials work at subatomic levels, studying breakthroughs such as piezoelectrics, which convert mechanical stress to electrical energy.

  5. Horizontal film balance having wide range and high sensitivity

    DOE Patents [OSTI]

    Abraham, B.M.; Miyano, K.; Ketterson, J.B.

    1983-11-08T23:59:59.000Z

    A thin-film, horizontal balance instrument is provided for measuring surface tension (surface energy) of thin films suspended on a liquid substrate. The balance includes a support bearing and an optical feedback arrangement for wide-range, high sensitivity measurements. The force on the instrument is balanced by an electromagnet, the current through the magnet providing a measure of the force applied to the instrument. A novel float construction is also disclosed. 5 figs.

  6. Horizontal film balance having wide range and high sensitivity

    DOE Patents [OSTI]

    Abraham, Bernard M. (Oak Park, IL); Miyano, Kenjiro (Downers Grove, IL); Ketterson, John B. (Evanston, IL)

    1983-01-01T23:59:59.000Z

    A thin-film, horizontal balance instrument is provided for measuring surface tension (surface energy) of thin films suspended on a liquid substrate. The balance includes a support bearing and an optical feedback arrangement for wide-range, high sensitivity measurements. The force on the instrument is balanced by an electromagnet, the current through the magnet providing a measure of the force applied to the instrument. A novel float construction is also disclosed.

  7. Horizontal film balance having wide range and high sensitivity

    DOE Patents [OSTI]

    Abraham, B.M.; Miyano, K.; Ketterson, J.B.

    1981-03-05T23:59:59.000Z

    A thin-film, horizontal balance instrument is provided for measuring surface tension (surface energy) of thin films suspended on a liquid substrate. The balance includes a support bearing and an optical feedback arrangement for wide-range, high sensitivity measurements. The force on the instrument is balanced by an electromagnet, the current through the magnet providing a measure of the force applied to the instrument. A novel float construction is also disclosed.

  8. Material accountancy for metallic fuel pin casting

    SciTech Connect (OSTI)

    Bucher, R.G.; Orechwa, Y.; Beitel, J.C.

    1995-08-01T23:59:59.000Z

    The operation of the Fuel Conditioning Facility (FCF) is based on the electrometallurgical processing of spent metallic reactor fuel. The pin casting operation, although only one of several operations in FCF, was the first to be on-line. As such, it has served to demonstrate the material accountancy system in many of its facets. This paper details, for the operation of the pin casting process with depleted uranium, the interaction between the mass tracking system (MTG) and some of the ancillary computer codes which generate pertinent information for operations and material accountancy. It is necessary to distinguish between two types of material balance calculations -- closeout for operations and material accountancy for safeguards. The two have much in common, for example, the mass tracking system database and the calculation of an inventory difference, but, in general, are not congruent with regard to balance period and balance spatial domain. Moreover, the objective, assessment, and reporting requirements of the calculated inventory difference are very different in the two cases.

  9. Projected refined product balances in key Latin American countries: A preliminary examination

    SciTech Connect (OSTI)

    NONE

    1996-06-01T23:59:59.000Z

    Over the years, the East-West Center (EWC) has developed considerable expertise in refinery modeling, especially in the area of forecasting product balances for countries, given planned capacity changes, changes in product demand, changes in crude slates, and changes in product specifications. This expertise has been applied on an ongoing basis to the major refiners in the Middle East and the Asia-Pacific region, along with the US West Coast as region in its own right. Refinery modeling in these three areas has been ongoing for nearly 15 years at the Center, and the tools and information sources are now well developed. To date, the EWC has not applied these tools to Latin America. Although research on Latin America has been an ongoing area of concern at the Center in recent years, the information gathered to date is still not of the level of detail nor quality available for other areas. The modeling efforts undertaken in this report are of a ``baseline`` nature, designed to outline the major issues, attempt a first cut at emerging product balances, and, above all, to elicit commentary from those directly involved in the oil industry in the key countries modeled. Our experience in other regions has shown that it takes a few years dialogue with refiners and government planner in individual countries to develop a reliable database, as well as the insights into operational constraints and practices that make accurate modeling possible. This report is no more than a first step down the road.

  10. Jet momentum balance independent of shear viscosity

    E-Print Network [OSTI]

    R. B. Neufeld

    2012-02-24T23:59:59.000Z

    Jet momentum balance measurements, such as those recently performed by the CMS collaboration, provide an opportunity to quantify the energy transferred from a parton shower to the underlying medium in heavy-ion collisions. Specifically, I argue that the Cooper-Frye freezeout distribution associated with the energy and momentum deposited by the parton shower is controlled to a significant extent by the distribution of the underlying bulk matter and independent of the details of how deposited energy is redistributed in the medium, which is largely determined by transport coefficients such as shear viscosity. Thus by matching the distribution of momentum associated with the secondary jet in such measurements to the thermal distribution of the underlying medium, one can obtain a model independent estimate on the amount of parton shower energy deposited.

  11. US/Russian program in materials protection, control and accounting at the RRC Kurchatov Institute: 1997--1998

    SciTech Connect (OSTI)

    Sukhoruchkin, V.; Rumyantsev, A.; Shmelev, V. [RRC Kurchatov Inst., Moscow (Russian Federation)] [and others

    1998-12-31T23:59:59.000Z

    Six US Department of Energy Laboratories are carrying out a program of cooperation with the Russian Research Center Kurchatov Institute to improve nuclear material protection, control and accounting (MPC and A) at Kurchatov. In 1997--1998 the primary thrust of this program has been directed to Building 106, which houses a number of test reactors and critical facilities. Substantial improvements in physical protection, upgrades in the physical inventory taking procedures, installation of equipment for the computerized materials accounting system, and installation of nuclear material portal monitors and neutron-based measurement equipment are being carried out at this facility. Software for the computerized accounting system, named KI-MACS, has been developed at Kurchatov and the system has been fully integrated with the bar code printing and reading equipment, electronic scales, and nondestructive assay equipment provided under this program. Additional 1997--1998 activities at Kurchatov include continuation of a tamper indicating device program, vulnerability assessments of several facilities, hosting of a Russian-American Workshop on Fissile Material Control and Accountability at Critical Facilities, and the development of accounting procedures for transfers of nuclear materials between material balance areas.

  12. Balanced Growth, Travel Demand, and Physical Activity

    E-Print Network [OSTI]

    Cervero, Robert; Duncan, Michael

    2006-01-01T23:59:59.000Z

    and Travel Patterns in the Puget Sound Transportation Panel.travel diary data from the Puget Sound area, Krizek foundhowever. In a study in the Puget Sound, Frank and Pivo (

  13. Western Area Power Administration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    29-30, 2011 2 Agenda * Overview of Western Area Power Administration * Post-1989 Loveland Area Projects (LAP) Marketing Plan * Energy Planning and Management Program * Development...

  14. Internal combustion engine cylinder-to-cylinder balancing with balanced air-fuel ratios

    DOE Patents [OSTI]

    Harris, Ralph E.; Bourn, Gary D.; Smalley, Anthony J.

    2006-01-03T23:59:59.000Z

    A method of balancing combustion among cylinders of an internal combustion engine. For each cylinder, a normalized peak firing pressure is calculated as the ratio of its peak firing pressure to its combustion pressure. Each cylinder's normalized peak firing pressure is compared to a target value for normalized peak firing pressure. The fuel flow is adjusted to any cylinder whose normalized peak firing pressure is not substantially equal to the target value.

  15. Hardfacing material

    DOE Patents [OSTI]

    Branagan, Daniel J. (Iona, ID)

    2012-01-17T23:59:59.000Z

    A method of producing a hard metallic material by forming a mixture containing at least 55% iron and at least one of boron, carbon, silicon and phosphorus. The mixture is formed into an alloy and cooled to form a metallic material having a hardness of greater than about 9.2 GPa. The invention includes a method of forming a wire by combining a metal strip and a powder. The metal strip and the powder are rolled to form a wire containing at least 55% iron and from two to seven additional elements including at least one of C, Si and B. The invention also includes a method of forming a hardened surface on a substrate by processing a solid mass to form a powder, applying the powder to a surface to form a layer containing metallic glass, and converting the glass to a crystalline material having a nanocrystalline grain size.

  16. GEOCHEMICAL MODELING OF F AREA SEEPAGE BASIN COMPOSITION AND VARIABILITY

    SciTech Connect (OSTI)

    Millings, M.; Denham, M.; Looney, B.

    2012-05-08T23:59:59.000Z

    From the 1950s through 1989, the F Area Seepage Basins at the Savannah River Site (SRS) received low level radioactive wastes resulting from processing nuclear materials. Discharges of process wastes to the F Area Seepage Basins followed by subsequent mixing processes within the basins and eventual infiltration into the subsurface resulted in contamination of the underlying vadose zone and downgradient groundwater. For simulating contaminant behavior and subsurface transport, a quantitative understanding of the interrelated discharge-mixing-infiltration system along with the resulting chemistry of fluids entering the subsurface is needed. An example of this need emerged as the F Area Seepage Basins was selected as a key case study demonstration site for the Advanced Simulation Capability for Environmental Management (ASCEM) Program. This modeling evaluation explored the importance of the wide variability in bulk wastewater chemistry as it propagated through the basins. The results are intended to generally improve and refine the conceptualization of infiltration of chemical wastes from seepage basins receiving variable waste streams and to specifically support the ASCEM case study model for the F Area Seepage Basins. Specific goals of this work included: (1) develop a technically-based 'charge-balanced' nominal source term chemistry for water infiltrating into the subsurface during basin operations, (2) estimate the nature of short term and long term variability in infiltrating water to support scenario development for uncertainty quantification (i.e., UQ analysis), (3) identify key geochemical factors that control overall basin water chemistry and the projected variability/stability, and (4) link wastewater chemistry to the subsurface based on monitoring well data. Results from this study provide data and understanding that can be used in further modeling efforts of the F Area groundwater plume. As identified in this study, key geochemical factors affecting basin chemistry and variability included: (1) the nature or chemistry of the waste streams, (2) the open system of the basins, and (3) duration of discharge of the waste stream types. Mixing models of the archetype waste streams indicated that the overall basin system would likely remain acidic much of the time. Only an extended periods of predominantly alkaline waste discharge (e.g., >70% alkaline waste) would dramatically alter the average pH of wastewater entering the basins. Short term and long term variability were evaluated by performing multiple stepwise modeling runs to calculate the oscillation of bulk chemistry in the basins in response to short term variations in waste stream chemistry. Short term (1/2 month and 1 month) oscillations in the waste stream types only affected the chemistry in Basin 1; little variation was observed in Basin 2 and 3. As the largest basin, Basin 3 is considered the primary source to the groundwater. Modeling showed that the fluctuation in chemistry of the waste streams is not directly representative of the source term to the groundwater (i.e. Basin 3). The sequence of receiving basins and the large volume of water in Basin 3 'smooth' or nullify the short term variability in waste stream composition. As part of this study, a technically-based 'charge-balanced' nominal source term chemistry was developed for Basin 3 for a narrow range of pH (2.7 to 3.4). An example is also provided of how these data could be used to quantify uncertainty over the long term variations in waste stream chemistry and hence, Basin 3 chemistry.

  17. Manual for Nuclear Materials Management and Safeguards System Reporting and Data Submission

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2003-08-19T23:59:59.000Z

    The manual provides detailed instructions for documenting and reporting data submissions for nuclear materials transactions, inventories, and material balances to the Nuclear Materials Management and Safeguards System (NMMSS). Cancels DOE M 474.1-2. Canceled by DOE M 470.4-6.

  18. Statistical methods for detecting loss of materials using NRTA data

    SciTech Connect (OSTI)

    Burr, T.; Coulter, A.; Hakkila, A. [Los Alamos National Lab., NM (United States); Ai, H.; Kadokura, I.; Fujimaki, K. [Japan Nuclear Fuel Ltd., Tokyo (Japan)

    1995-12-31T23:59:59.000Z

    The authors selected eight sequential statistical tests and studied their performance on near-real-time-accounting (NRTA) data that is nominally what is expected from the proposed Rokkasho Reprocessing Plant in Japan. The effort divided into three main activities: (1) use process-flow information to determine process vessel inventories and transfers at the time of material balance closure, (2) use variance propagation methods to estimate the variance-covariance matrix of a sequence of material balances, and (3) study the performance of eight sequential tests on a variety of loss scenarios. This paper describes the results of these three activities.

  19. Materials Science

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHighand Retrievals from a New 183-GHzMARSecurityMaterials Science Materials

  20. Hydrologically Sensitive Areas: Variable Source Area Hydrology

    E-Print Network [OSTI]

    Walter, M.Todd

    Hydrologically Sensitive Areas: Variable Source Area Hydrology Implications for Water Quality Risk hydrology was developed and applied to the New York City (NYC) water supply watersheds. According and are therefore hydrologically sensitive with respect to their potential to transport contaminants to perennial

  1. Material and energy recovery in integrated waste management systems. An evaluation based on life cycle assessment

    SciTech Connect (OSTI)

    Giugliano, Michele; Cernuschi, Stefano [Politecnico di Milano - DIIAR, Environmental Section, P.zza Leonardo da Vinci, 32, 20133 Milano (Italy); Grosso, Mario, E-mail: mario.grosso@polimi.it [Politecnico di Milano - DIIAR, Environmental Section, P.zza Leonardo da Vinci, 32, 20133 Milano (Italy); Rigamonti, Lucia [Politecnico di Milano - DIIAR, Environmental Section, P.zza Leonardo da Vinci, 32, 20133 Milano (Italy)

    2011-09-15T23:59:59.000Z

    This paper reports the environmental results, integrated with those arising from mass and energy balances, of a research project on the comparative analysis of strategies for material and energy recovery from waste, funded by the Italian Ministry of Education, University and Research. The project, involving the cooperation of five University research groups, was devoted to the optimisation of material and energy recovery activities within integrated municipal solid waste (MSW) management systems. Four scenarios of separate collection (overall value of 35%, 50% without the collection of food waste, 50% including the collection of food waste, 65%) were defined for the implementation of energetic, environmental and economic balances. Two sizes of integrated MSW management system (IWMS) were considered: a metropolitan area, with a gross MSW production of 750,000 t/year and an average province, with a gross MSW production of 150,000 t/year. The environmental analysis was conducted using Life Cycle Assessment methodology (LCA), for both material and energy recovery activities. In order to avoid allocation we have used the technique of the expansion of the system boundaries. This means taking into consideration the impact on the environment related to the waste management activities in comparison with the avoided impacts related to the saving of raw materials and primary energy. Under the hypotheses of the study, both for the large and for the small IWMS, the energetic and environmental benefits are higher than the energetic and environmental impacts for all the scenarios analysed in terms of all the indicators considered: the scenario with 50% separate collection in a drop-off scheme excluding food waste shows the most promising perspectives, mainly arising from the highest collection (and recycling) of all the packaging materials, which is the activity giving the biggest energetic and environmental benefits. Main conclusions of the study in the general field of the assessment of the environmental performance of any integrated waste management scheme address the importance of properly defining, beyond the design value assumed for the separate collection as a whole, also the yields of each material recovered; particular significance is finally related to the amount of residues deriving from material recovery activities, resulting on average in the order of 20% of the collected materials.

  2. Heuristics for Balancing Turbine Fans Samir V. Amiouny

    E-Print Network [OSTI]

    Bartholdi III, John J.

    Reiger, 1986. In some cases, such as in the constructionof hydraulic, steam or gas turbines, fan bladesHeuristics for Balancing Turbine Fans Samir V. Amiouny John J. Bartholdi, III John H. Vande Vate April 20, 1997 Abstract We develop heuristics for a problem that models the static balancing of turbine

  3. Robust Control-theoretic Thermal Balancing for Server Clusters

    E-Print Network [OSTI]

    Lu, Chenyang

    Robust Control-theoretic Thermal Balancing for Server Clusters Yong Fu, Chenyang Lu, Hongan Wang for clusters because of the increasing power consumption of modern processors, compact server architectures and growing server density in data centers. Thermal balancing mitigates hot spots in a cluster through dynamic

  4. Net Balanced Floorplanning Based on Elastic Energy Model

    E-Print Network [OSTI]

    Nannarelli, Alberto

    Net Balanced Floorplanning Based on Elastic Energy Model Wei Liu and Alberto Nannarelli Dept variations can introduce extra signal skew, it is desirable to have floorplans with balanced net delays based on the elastic energy model. The B*-tree, which is based on an ordered binary tree, is used

  5. Seasonal mass balance gradients in Norway L. A. Rasmussen1

    E-Print Network [OSTI]

    Rasmussen, L.A.

    16 Aug 05 Seasonal mass balance gradients in Norway L. A. Rasmussen1 and L. M. Andreassen2 1 Norwegian Water Resources and Energy Directorate (NVE) P. O. Box 5091 Majorstua, N-0301 Oslo, Norway in Norway exists in their profiles of both seasonal balances, winter bw(z) and summer bs(z). Unlike many

  6. A Practical Approach to Dynamic Load Balancing Jerrell Watts

    E-Print Network [OSTI]

    Transfer Vector Calculation ¢ ¡ ¢ £ ¤ £ ¢ ¡ ¢ ¢ ¡ ¢ ¡ ¢ ¡ ¢ £ ¤ £ ¢ ¤ £ ¢ 8 2.3.1 Heat DiffusionA Practical Approach to Dynamic Load Balancing Jerrell Watts Scalable Concurrent Programming versions of the node adaption and movement routines which were used by the load balancing code; he also

  7. AREA COORDINATOR RESIDENTIAL EDUCATION

    E-Print Network [OSTI]

    Bordenstein, Seth

    AREA COORDINATOR RESIDENTIAL EDUCATION VANDERBILT UNIVERSITY, NASHVILLE, TENNESSEE The Office of Housing and Residential Education at Vanderbilt University is seeking applicants for an Area Coordinator. The Area Coordinator is responsible for assisting in the management and operation of a residential area

  8. Means and method of balancing multi-cylinder reciprocating machines

    DOE Patents [OSTI]

    Corey, John A. (North Troy, NY); Walsh, Michael M. (Schenectady, NY)

    1985-01-01T23:59:59.000Z

    A virtual balancing axis arrangement is described for multi-cylinder reciprocating piston machines for effectively balancing out imbalanced forces and minimizing residual imbalance moments acting on the crankshaft of such machines without requiring the use of additional parallel-arrayed balancing shafts or complex and expensive gear arrangements. The novel virtual balancing axis arrangement is capable of being designed into multi-cylinder reciprocating piston and crankshaft machines for substantially reducing vibrations induced during operation of such machines with only minimal number of additional component parts. Some of the required component parts may be available from parts already required for operation of auxiliary equipment, such as oil and water pumps used in certain types of reciprocating piston and crankshaft machine so that by appropriate location and dimensioning in accordance with the teachings of the invention, the virtual balancing axis arrangement can be built into the machine at little or no additional cost.

  9. Materials compatibility.

    SciTech Connect (OSTI)

    Somerday, Brian P.

    2010-04-01T23:59:59.000Z

    Objectives are to enable development and implementation of codes and standards for H{sub 2} containment components: (1) Evaluate data on mechanical properties of materials in H{sub 2} gas - Technical Reference on Hydrogen Compatibility of Materials; (2) Generate new benchmark data on high-priority materials - Pressure vessel steels, stainless steels; and (3) Establish procedures for reliable materials testing - Sustained-load cracking, fatigue crack propagation. Summary of this presentation are: (1) Completed measurement of cracking thresholds (K{sub TH}) for Ni-Cr-Mo pressure vessel steels in high-pressure H{sub 2} gas - K{sub TH} measurements required in ASME Article KD-10 (2) Crack arrest test methods appear to yield non-conservative results compared to crack initiation test methods - (a) Proposal to insert crack initiation test methods in Article KD-10 will be presented to ASME Project Team on Hydrogen Tanks, and (b) Crack initiation methods require test apparatus designed for dynamic loading of specimens in H{sub 2} gas; and (3) Demonstrated ability to measure fatigue crack growth of pressure vessel steels in high-pressure H{sub 2} gas - (a) Fatigue crack growth data in H{sub 2} required in ASME Article KD-10, and (b) Test apparatus is one of few in U.S. or abroad for measuring fatigue crack growth in >100 MPa H{sub 2} gas.

  10. NANO EXPRESS Fabrication of Large Area Periodic Nanostructures Using

    E-Print Network [OSTI]

    Mohseni, Hooman

    , such as photonic band-gap materials, high dense data storage, and photonic devices. We have developed a maskless areas, such as photonic band-gap materials [1], high dense data storage [2], and photonic devices [3NANO EXPRESS Fabrication of Large Area Periodic Nanostructures Using Nanosphere Photolithography

  11. Hydro-Balanced Stuffing Box field test

    SciTech Connect (OSTI)

    Giangiacomo, L.A.

    1999-05-28T23:59:59.000Z

    The Hydro-Balanced Stuffing Box is a seal assembly for polished rod pumping installations commonly used in oil and gas pumping well installations to contain produced well fluids. The improved stuffing box was developed and patented by Harold H. Palmour of The Palmour Group of Livingston, TX. The stuffing box is designed to reduce the incidence of seal leakage and to utilize an environmentally safe fluid, so that if there is any leakage, environmental damage is reduced or eliminated. The unit was tested on two wells at the Rocky Mountain Oilfield Testing Center. During the test period, the performance of the stuffing box was measured by monitoring the pressure on the tubing and the inner chamber with a Barton Two-pen recorder. The amount of safe fluid consumed, fluid leakage at the top of the stuffing box, pressure supplied from the nitrogen bottle, ambient temperature, and polish rod temperature was recorded. The stuffing box is capable of providing a better seal between well fluids an d the environment than conventional stuffing boxes. It allows the polished rod to operate cooler and with lubrication, extending the life of the packing elements, and reducing the amount of attention required to prevent leakage.

  12. Interstellar Turbulence, Cloud Formation and Pressure Balance

    E-Print Network [OSTI]

    Enrique Vazquez-Semadeni

    1998-10-23T23:59:59.000Z

    We discuss HD and MHD compressible turbulence as a cloud-forming and cloud-structuring mechanism in the ISM. Results from a numerical model of the turbulent ISM at large scales suggest that the phase-like appearance of the medium, the typical values of the densities and magnetic field strengths in the intercloud medium, as well as Larson's velocity dispersion-size scaling relation in clouds may be understood as consequences of the interstellar turbulence. However, the density-size relation appears to only hold for the densest simulated clouds, there existing a large population of small, low-density clouds, which, on the other hand, are hardest to observe. We then discuss several tests and implications of a fully dynamical picture of interstellar clouds. The results imply that clouds are transient, constantly being formed, distorted and disrupted by the turbulent velocity field, with a fraction of these fluctuations undergoing gravitational collapse. Simulated line profiles and estimated cloud lifetimes are consistent with observational data. In this scenario, we suggest it is quite unlikely that quasi-hydrostatic structures on any scale can form, and that the near pressure balance between clouds and the intercloud medium is an incidental consequence of the density field driven by the turbulence and in the presence of appropriate cooling, rather than a driving or confining mechanism.

  13. Balanced homodyne detectors and Casimir energy densities

    E-Print Network [OSTI]

    P. Marecki

    2008-03-22T23:59:59.000Z

    We recall and generalize the analysis of the output of the so-called balanced homodyne detectors. The most important feature of these detectors is their ability to quantify the vacuum fluctuations of the electric field, that is expectation values of products of (quantum-) electric-field operators. More precisely, the output of BHDs provides information on the one- and two-point functions of arbitrary states of quantum fields. We generalize the analysis of the response of BHDs to the case of quantum fields under influence of static external conditions such as cavities or polarizable media. By recalling the expressions for two-point functions of quantum fields in Casimir geometries we show, that a rich, position- and frequency-dependent pattern of BHD responses is predicted for ground states. This points to a potentially new characterization of quantum fields in Casimir setups which would not only complement the current global methods (Casimir forces), but also improve understanding of sub-vacuum energy densities present in some regions in these geometries.

  14. Nanostructure material for supercapacitor application

    SciTech Connect (OSTI)

    Huang, Y.; Chu, C.T.; Wei, Q.; Zheng, H.

    2000-07-01T23:59:59.000Z

    Transition metal nitrides and carbonitride materials were fabricated via sol-gel technology. The transition metal amides were synthesized by two methods: chemical route and electrolysis. The transition metal amides were then further polymerized, sintering to high temperature in an inert or reduced atmosphere. Transition metal nitrides and carbonitrides powders with surface area up to 160 m{sup 2}/g were obtained. The resultant electrode material showed high specific capacitance as crystalline ruthenium oxide.

  15. Liquid balance monitoring inside conventional, Retrofit, and bio-reactor landfill cells

    SciTech Connect (OSTI)

    Abichou, Tarek, E-mail: abichou@eng.fsu.edu [Department of Civil and Environmental Engineering, Florida State University, 2525 Pottsdamer Street, Tallahassee, FL 32311 (United States); Barlaz, Morton A. [Department of Civil, Construction, and Environmental Engineering, North Carolina State University, Raleigh, NC 27695 (United States); Green, Roger; Hater, Gary [Waste Management Inc., Cincinnati, OH 45211 (United States)

    2013-10-15T23:59:59.000Z

    Highlights: • The Retrofit, Control, and As-Built cells received 48, 14, and 213 L Mg{sup ?1} (liters of liquids per metric ton of waste). • The leachate collection system yielded 60, 57 and 198 L Mg{sup ?1} from the Retrofit, Control, and As-Built cells. • The head on liner in all cells was below regulatory limits. • Measured moisture content of the waste samples was consistent with that calculated from accumulated liquid by balance. • The in-place saturated hydraulic conductivity of the MSW was calculated to be in the range of 10{sup ?8} to 10{sup ?7} m s{sup ?1}. - Abstract: The Outer Loop landfill bioreactor (OLLB) in Louisville, KY, USA has been the site of a study to evaluate long-term bioreactor performance at a full-scale operational landfill. Three types of landfill units were studied including a conventional landfill (Control cell), a new landfill area that had an air addition and recirculation piping network installed as waste was being placed (As-Built cell), and a conventional landfill that was modified to allow for liquids recirculation (Retrofit cell). During the monitoring period, the Retrofit, Control, and As-Built cells received 48, 14, and 213 L Mg{sup ?1} (liters of liquids per metric ton of waste), respectively. The leachate collection system yielded 60, 57 and 198 L Mg{sup ?1} from the Retrofit, Control, and As-Built cells, respectively. The head on liner in all cells was below regulatory limits. In the Control and As-Built cells, leachate head on liner decreased once waste placement stopped. The measured moisture content of the waste samples was consistent with that calculated from the estimate of accumulated liquid by the liquid balance. Additionally, measurements on excavated solid waste samples revealed large spatial variability in waste moisture content. The degree of saturation in the Control cells decreased from 85% to 75%. The degree of saturation increased from 82% to 83% due to liquids addition in the Retrofit cells and decreased back to 80% once liquid addition stopped. In the As-Built cells, the degree of saturation increased from 87% to 97% during filling activities and then started to decrease soon after filling activities stopped to reach 92% at the end of the monitoring period. The measured leachate generation rates were used to estimate an in-place saturated hydraulic conductivity of the MSW in the range of 10{sup ?8} to 10{sup ?7} m s{sup ?1} which is lower than previous reports. In the Control and Retrofit cells, the net loss in liquids, 43 and 12 L Mg{sup ?1}, respectively, was similar to the measured settlement of 15% and 5–8% strain, respectively (Abichou et al., 2013). The increase in net liquid volume in the As-Built cells indicates that the 37% (average) measured settlement strain in these cells cannot be due to consolidation as the waste mass did not lose any moisture but rather suggests that settlement was attributable to lubrication of waste particle contacts, softening of flexible porous materials, and additional biological degradation.

  16. World copper smelter sulfur balance, 1988. (Information circular, 1993). Information circular/1993

    SciTech Connect (OSTI)

    Towle, S.W.

    1993-01-01T23:59:59.000Z

    In 1989, the US Bureau of Mines initiated a contract to gather engineering, operating, and environmental cost data for 1988 for 30 major foreign primary copper smelters in market economy countries. Data were collected for 29 of the designated smelters together with information on applicable environmental regulations. Materials balance data obtained were used with available data for the eight US smelters to determine the approximate extent of copper smelter sulfur emission control in 1988. A broad characterization of the status of sulfur emission control regulation was made. Significant changes since 1988 that may increase sulfur emission control are noted.

  17. ORNL trends and balances, 1987-1992

    SciTech Connect (OSTI)

    Not Available

    1987-01-01T23:59:59.000Z

    A brief overview is given that covers the roles, organization, R and D sponsors, and recent achievements of Oak Ridge National Laboratory. Current R and D programs are described in the areas of nuclear and engineering technologies, advanced energy systems, biomedical and environmental sciences, and basic physical sciences. ORNL's future activities are discussed. (LEW)

  18. M-Area basin closure, Savannah River Site

    SciTech Connect (OSTI)

    McMullin, S.R.; Horvath, J.G.

    1991-12-31T23:59:59.000Z

    M-Area, on the Savannah River Site, processes raw materials and manufactures fuel and target rods for reactor use. Effluent from these processes were discharged into the M-Area settling basin and Lost Lake, a natural wetland. The closure of this basin began in 1988 and included the removal and stabilization of basin fluids, excavation of all contaminated soils from affected areas and Lost Lake, and placement of all materials in the bottom of the emptied basin. These materials were covered with a RCRA style cap, employing redundant barriers of kaolin clay and geosynthetic material. Restoration of excavated uplands and wetlands is currently underway.

  19. M-Area basin closure, Savannah River Site

    SciTech Connect (OSTI)

    McMullin, S.R.; Horvath, J.G.

    1991-01-01T23:59:59.000Z

    M-Area, on the Savannah River Site, processes raw materials and manufactures fuel and target rods for reactor use. Effluent from these processes were discharged into the M-Area settling basin and Lost Lake, a natural wetland. The closure of this basin began in 1988 and included the removal and stabilization of basin fluids, excavation of all contaminated soils from affected areas and Lost Lake, and placement of all materials in the bottom of the emptied basin. These materials were covered with a RCRA style cap, employing redundant barriers of kaolin clay and geosynthetic material. Restoration of excavated uplands and wetlands is currently underway.

  20. Fossil energy materials needs assessment

    SciTech Connect (OSTI)

    King, R.T.; Judkins, R.R. (comps.)

    1980-07-01T23:59:59.000Z

    An assessment of needs for materials of construction for fossil energy systems was prepared by ORNL staff members who conducted a literature search and interviewed various individuals and organizations that are active in the area of fossil energy technology. Critical materials problems associated with fossil energy systems are identified. Background information relative to the various technologies is given and materials research needed to enhance the viability and improve the economics of fossil energy processes is discussed. The assessment is presented on the basis of materials-related disciplines that impact fossil energy material development. These disciplines include the design-materials interface, materials fabrication technology, corrosion and materials compatibility, wear phenomena, ceramic materials, and nondestructive testing. The needs of these various disciplines are correlated with the emerging fossil energy technologies that require materials consideration. Greater emphasis is given to coal technology - particularly liquefaction, gasification, and fluidized bed combustion - than to oil and gas technologies because of the perceived inevitability of US dependence on coal conversion and utilization systems as a major part of our total energy production.

  1. Self-Assembly of Virus-Structured High Surface Area Nanomaterials and Their Application as Battery Electrodes

    E-Print Network [OSTI]

    Rubloff, Gary W.

    arrays, and energy storage devices. Increased surface areas are generally achieved through the synthesis for the self-assembly of high surface area nanostructured materials and devices. One approach is templating for the fabrication of oriented high surface area materials. Introduction High surface area nanostructured materials

  2. Building America Case Study: Balancing Hydronic Systems in Multifamily Buildings, Chicago, Illinois (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2014-09-01T23:59:59.000Z

    In multifamily hydronic systems, temperature imbalance may be caused by undersized piping, improperly adjusted balancing valves, inefficient water temperature and flow levels, and owner/occupant interaction with the boilers, distribution and controls. The effects of imbalance include tenant discomfort, higher energy use intensity and inefficient building operation. This paper explores cost-effective distribution upgrades and balancing measures in multifamily hydronic systems, providing a resource to contractors, auditors, and building owners on best practices to improve tenant comfort and lower operating costs. The research was conducted by The Partnership for Advanced Residential Retrofit (PARR) in conjunction with Elevate Energy. The team surveyed existing knowledge on cost-effective retrofits for optimizing distribution in typical multifamily hydronic systems, with the aim of identifying common situations and solutions, and then conducted case studies on two Chicago area buildings with known balancing issues in order to quantify the extent of temperature imbalance. At one of these buildings a booster pump was installed on a loop to an underheated wing of the building. This study found that unit temperature in a multifamily hydronic building can vary as much as 61 degrees F, particularly if windows are opened or tenants use intermittent supplemental heating sources like oven ranges. Average temperature spread at the building as a result of this retrofit decreased from 22.1 degrees F to 15.5 degrees F.

  3. Pulse*Star Inertial Confinement Fusion Reactor: heat transfer loop and balance of plant considerations

    SciTech Connect (OSTI)

    McDowell, M.W.; Murray, K.A.

    1984-05-09T23:59:59.000Z

    A conceptual heat transfer loop and balance of plant design for the Pulse*Star Inertial Confinement Fusion Reactor has been investigated and results are presented. The Pulse*Star reaction vessel, a perforated steel bell jar approximately 11 m in diameter, is immersed in Li/sub 17/Pb/sub 83/ coolant which flows through the perforations and forms a 1.5 m thick plenum of droplets around an 8 m diameter inner chamber. The reactor and associated pumps, piping, and steam generators are contained within a 17 m diameter pool of Li/sub 17/Pb/sub 83/ coolant to minimize structural requirements and occupied space, resulting in reduced cost. Four parallel heat transfer loops with flow rates of 5.5 m/sup 3//s each are necessary to transfer 3300 MWt of power. The steam generator design was optimized by finding the most cost-effective combination of heat exchanger area and pumping power. Power balance calculations based on an improved electrical conversion efficiency revealed a net electrical output of 1260 MWe to the bus bar and a resulting net efficiency of 39%. Suggested balance-of-plant layouts are also presented.

  4. Environmental Health & Safety, UC Irvine TITLE: CLEAN AREAS IN RESEARCH LABS (Non-Clinical)

    E-Print Network [OSTI]

    George, Steven C.

    . Relocate all hazardous materials use and storage from the Clean Area and maintain separation distance an adequate separation of the Clean Area from hazardous operations is not possible, splash is focused upon the adequacy of separation of the proposed Clean Area from areas in which hazardous materials

  5. Energy Materials & Processes | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Materials & Processes Overview Atmospheric Aerosol Systems Biosystem Dynamics & Design Energy Materials & Processes Terrestrial & Subsurface Ecosystems Energy Materials &...

  6. Material accountancy in the Ningyo-Toge uranium enrichment pilot plant

    SciTech Connect (OSTI)

    Akiba, M; Iwamoto, T.; Hori, M.; Ikeda, K.; Tani, A.

    1987-01-01T23:59:59.000Z

    The uranium enrichment pilot plant at PNC Ningyo-Toge Works, Japan, started operation in August 1979. Since then, inspection activities by the government of Japan and the International Atomic Energy Agency (IAEA) have been carried out. A basic measure of safeguards is evaluation of material unaccounted for (MUF) by closing the material balance. As the plant now produces uranium of <5% enrichment, a material balance is closed only once a year. Until now, eight physical inventories have been taken. This paper describes the operator's procedures for material accountability and the values of MUF reported to the government of Japan and the IAEA.

  7. The energy balance in polars revisited

    E-Print Network [OSTI]

    Gavin Ramsay; Mark Cropper

    2003-09-19T23:59:59.000Z

    In the EXOSAT and ROSAT eras a significant number of polars were found to show a soft/hard X-ray ratio much greater than that expected from the standard accretion shock model. This was known as the `soft X-ray excess'. We have made an snapshot survey of polars using XMM-Newton and determined their soft/hard ratios. We find that less than one in five of systems show a significant soft X-ray excess, while the rest show ratios consistent with that predicted by the standard model. We have investigated the discrepancy between this and the previous investigations by re-examining all the available ROSAT PSPC pointed observations of polars using more recent calibrations than in the original studies. We find that these data show an energy balance ratio which is broadly consistent with that of our XMM-Newton results. We conclude that the previous studies were affected by the data being less well calibrated. We discuss which physical mechanisms might give rise to a high soft X-ray excess and whether systems with high ratios show more variation in soft X-rays. Surprisingly, we find that 6 out of 21 systems found in a high accretion state did not show a distinct soft X-ray component. Two systems showed one pole with such a component and one which did not. Based on the ratio of the observed soft X-ray to UV flux measurements (which were obtained simultaneously using the Optical Monitor) we suggest that this is because the reprocessed component in these systems is cool enough to have moved out of the soft X-ray band and into the EUV or UV band.

  8. Plutonium focus area: Technology summary

    SciTech Connect (OSTI)

    NONE

    1996-03-01T23:59:59.000Z

    To ensure research and development programs focus on the most pressing environmental restoration and waste management problems at the U.S. Department of Energy (DOE), the Assistant Secretary for the Office of Environmental Management (EM) established a working group in August 1993 to implement a new approach to research and technology development. As part of this approach, EM developed a management structure and principles that led to creation of specific focus areas. These organizations were designed to focus scientific and technical talent throughout DOE and the national scientific community on major environmental restoration and waste management problems facing DOE. The focus area approach provides the framework for inter-site cooperation and leveraging of resources on common problems. After the original establishment of five major focus areas within the Office of Technology Development (EM-50), the Nuclear Materials Stabilization Task Group (NMSTG, EM-66) followed EM-50`s structure and chartered the Plutonium Focus Area (PFA). NMSTG`s charter to the PFA, described in detail later in this book, plays a major role in meeting the EM-66 commitments to the Defense Nuclear Facilities Safety Board (DNFSB). The PFA is a new program for FY96 and as such, the primary focus of revision 0 of this Technology Summary is an introduction to the Focus Area; its history, development, and management structure, including summaries of selected technologies being developed. Revision 1 to the Plutonium Focus Area Technology Summary is slated to include details on all technologies being developed, and is currently planned for release in August 1996. The following report outlines the scope and mission of the Office of Environmental Management, EM-60, and EM-66 organizations as related to the PFA organizational structure.

  9. Wetland Preservation Areas (Minnesota)

    Broader source: Energy.gov [DOE]

    A wetland owner can apply to the host county for designation of a wetland preservation area. Once designated, the area remains designated until the owner initiates expiration, except where a state...

  10. Thermal balance and photon-number quantization in layered structures

    E-Print Network [OSTI]

    Mikko Partanen; Teppo Häyrynen; Jani Oksanen; Jukka Tulkki

    2014-03-17T23:59:59.000Z

    The quantization of the electromagnetic field in lossy and dispersive dielectric media has been widely studied during the last few decades. However, several aspects of energy transfer and its relation to consistently defining position-dependent ladder operators for the electromagnetic field in nonequilibrium conditions have partly escaped the attention. In this work we define the position-dependent ladder operators and an effective local photon-number operator that are consistent with the canonical commutation relations and use these concepts to describe the energy transfer and thermal balance in layered geometries. This approach results in a position-dependent photon-number concept that is simple and consistent with classical energy conservation arguments. The operators are formed by first calculating the vector potential operator using Green's function formalism and Langevin noise source operators related to the medium and its temperature, and then defining the corresponding position-dependent annihilation operator that is required to satisfy the canonical commutation relations in arbitrary geometry. Our results suggest that the effective photon number associated with the electric field is generally position dependent and enables a straightforward method to calculate the energy transfer rate between the field and the local medium. In particular, our results predict that the effective photon number in a vacuum cavity formed between two lossy material layers can oscillate as a function of the position suggesting that also the local field temperature oscillates. These oscillations are expected to be directly observable using relatively straightforward experimental setups in which the field-matter interaction is dominated by the coupling to the electric field.

  11. Evidence of critical balance in kinetic Alfven wave turbulence simulations

    SciTech Connect (OSTI)

    TenBarge, J. M.; Howes, G. G. [Department of Physics and Astronomy, University of Iowa, Iowa City, Iowa 52242 (United States)

    2012-05-15T23:59:59.000Z

    A numerical simulation of kinetic plasma turbulence is performed to assess the applicability of critical balance to kinetic, dissipation scale turbulence. The analysis is performed in the frequency domain to obviate complications inherent in performing a local analysis of turbulence. A theoretical model of dissipation scale critical balance is constructed and compared to simulation results, and excellent agreement is found. This result constitutes the first evidence of critical balance in a kinetic turbulence simulation and provides evidence of an anisotropic turbulence cascade extending into the dissipation range. We also perform an Eulerian frequency analysis of the simulation data and compare it to the results of a previous study of magnetohydrodynamic turbulence simulations.

  12. Control of carbon balance in a silicon smelting furnace

    DOE Patents [OSTI]

    Dosaj, V.D.; Haines, C.M.; May, J.B.; Oleson, J.D.

    1992-12-29T23:59:59.000Z

    The present invention is a process for the carbothermic reduction of silicon dioxide to form elemental silicon. Carbon balance of the process is assessed by measuring the amount of carbon monoxide evolved in offgas exiting the furnace. A ratio of the amount of carbon monoxide evolved and the amount of silicon dioxide added to the furnace is determined. Based on this ratio, the carbon balance of the furnace can be determined and carbon feed can be adjusted to maintain the furnace in carbon balance.

  13. Analysis Methodology for Balancing Authority Cooperation in High Penetration of Variable Generation

    SciTech Connect (OSTI)

    Makarov, Yuri V.; Etingov, Pavel V.; Zhou, Ning; Ma, Jian; Samaan, Nader A.; Diao, Ruisheng; Malhara, Sunita V.; Guttromson, Ross T.; Du, Pengwei; Sastry, Chellury

    2010-02-01T23:59:59.000Z

    With the rapidly growing penetration level of wind and solar generation, the challenges of managing variability and the uncertainty of intermittent renewable generation become more and more significant. The problem of power variability and uncertainty gets exacerbated when each balancing authority (BA) works locally and separately to balance its own subsystem. The virtual BA concept means various forms of collaboration between individual BAs must manage power variability and uncertainty. The virtual BA will have a wide area control capability in managing its operational balancing requirements in different time frames. This coordination results in the improvement of efficiency and reliability of power system operation while facilitating the high level integration of green, intermittent energy resources. Several strategies for virtual BA implementation, such as ACE diversity interchange (ADI), wind only BA, BA consolidation, dynamic scheduling, regulation and load following sharing, extreme event impact study are discussed in this report. The objective of such strategies is to allow individual BAs within a large power grid to help each other deal with power variability. Innovative methods have been developed to simulate the balancing operation of BAs. These methods evaluate the BA operation through a number of metrics — such as capacity, ramp rate, ramp duration, energy and cycling requirements — to evaluate the performances of different virtual BA strategies. The report builds a systematic framework for evaluating BA consolidation and coordination. Results for case studies show that significant economic and reliability benefits can be gained. The merits and limitation of each virtual BA strategy are investigated. The report provides guidelines for the power industry to evaluate the coordination or consolidation method. The application of the developed strategies in cooperation with several regional BAs is in progress for several off-spring projects.

  14. Photovoltaic balance-of-system designs and costs at PVUSA

    SciTech Connect (OSTI)

    Reyes, A.B.; Jennings, C.

    1995-05-01T23:59:59.000Z

    This report is one in a series of 1994-1995 PVUSA reports that document PVUSA lessons learned at demonstration sites in California and Texas. During the last 7 years (1988 to 1994), 16 PV systems ranging from 20 kW to 500 kW have been installed. Six 20-kW emerging module technology (EMT) arrays and three turnkey (i.e., vendor designed and integrated) utility-scale systems were procured and installed at PVUSA`s main test site in Davis, California. PVUSA host utilities have installed a total of seven EMT arrays and utility-scale systems in their service areas. Additional systems at Davis and host utility sites are planned. One of PVUSA`s key objectives is to evaluate the performance, reliability, and cost of PV balance-of-system (BOS). In the procurement stage PVUSA encouraged innovative design to improve upon present practice by reducing maintenance, improving reliability, or lowering manufacturing or construction costs. The project team worked closely with suppliers during the design stage not only to ensure designs met functional and safety specifications, but to provide suggestions for improvement. This report, intended for the photovoltaic (PV) industry and for utility project managers and engineers considering PV plant construction and ownership, documents PVUSA utility-scale system design and cost lessons learned. Complementary PVUSA topical reports document: construction and safety experience; five-year assessment of EMTs; validation of the Kerman 500-kW grid-support PV plant benefits; PVUSA instrumentation and data analysis techniques; procurement, acceptance, and rating practices for PV power plants; experience with power conditioning units and power quality.

  15. Surface Energy Balance Measurements Above an Exurban Residential Neighbourhood of Kansas City, Missouri

    E-Print Network [OSTI]

    Balogun, Ahmed A.; Adegoke, Jimmy O.; Vezhapparambu, Sajith; Mauder, Matthias; McFadden, Joseph P.; Gallo, Kevin

    2009-01-01T23:59:59.000Z

    1999) The energy balance of central Mexico City during theEnergy and radiation balance of a central European city. IntT (1999) Energy balance ?uxes in a subtropical city: Miami

  16. The effect of post-fire stand age on the boreal forest energy balance

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    R. , Lee, X. , 1997. Energy balance and canopy conductanceon the boreal forest energy balance B.D. Amiro a,b, *, A.L.reserved. Keywords: Energy balance; Forest fire; Boreal

  17. area material storage: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Temporary (mobile) storage testing facilities Permanent storage testing facilities* 1MW PV array.nrel.govwind NWTC Controllable Grid Interface NREL's new controllable grid...

  18. Supplementary Material: Segmentation with Area Constraints Marc Niethammera,b

    E-Print Network [OSTI]

    - ators, the ADMM dual energy, and the derivation of the estimate of the relaxed dual energy. Keywords dual energy, and the estimate of the relaxed dual energy respectively. S.1. Full vesicle segmentation

  19. Supplementary Material for "Differential Connectivity Within the Parahippocampal Place Area"

    E-Print Network [OSTI]

    Li, Fei-Fei

    7411. #12;-0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 ** LOC TOS RSC cIPL CorrelationbetweenWeightmap and. 2b). Although this approach can successfully detect that LOC and TOS are preferentially connected to posterior PPA, it fails to show significant effects for RSC and cIPL (LOC: t17 = 6.02, p TOS: t17

  20. Laboratory to demolish excavation enclosures at Material Disposal Area B

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)Integrated Codes |Is Your Home asLCLSLaboratoryRowland to receive DOEnear DP Road

  1. Laboratory to demolish excavation enclosures at Material Disposal Area B

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)Integrated Codes |Is Your Home asLCLSLaboratoryRowland to receive DOEnear DP

  2. Laboratory to demolish excavation enclosures at Material Disposal Area B

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)Integrated Codes |Is Your Home asLCLSLaboratoryRowland to receive DOEnear DPnear DP

  3. Protected Areas Stacy Philpott

    E-Print Network [OSTI]

    Gottgens, Hans

    · Convention of Biological Diversity, 1992 #12;IUCN Protected Area Management Categories Ia. Strict Nature. Protected Landscape/ Seascape VI. Managed Resource Protected Area #12;Ia. Strict Nature Preserves and Ib. Wilderness Areas · Natural preservation · Research · No · No #12;II. National Parks · Ecosystem protection

  4. Service Entry Delivery Area

    E-Print Network [OSTI]

    New South Wales, University of

    Catheter Lab Boiler House Main Entry Short Street ChapelStreet Vehicle Exit 23. Gray Street Car ParkingService Entry Waste Handling Area Delivery Area Admissions Entrance Inquiries Desk Cafeteria Coffee in July 2000 Vehicle Entry Emergency Main Entrance TOKOGARAHRAILWAYSTATION LEGEND Areas under construction

  5. Alloy materials

    DOE Patents [OSTI]

    Hans Thieme, Cornelis Leo (Westborough, MA); Thompson, Elliott D. (Coventry, RI); Fritzemeier, Leslie G. (Acton, MA); Cameron, Robert D. (Franklin, MA); Siegal, Edward J. (Malden, MA)

    2002-01-01T23:59:59.000Z

    An alloy that contains at least two metals and can be used as a substrate for a superconductor is disclosed. The alloy can contain an oxide former. The alloy can have a biaxial or cube texture. The substrate can be used in a multilayer superconductor, which can further include one or more buffer layers disposed between the substrate and the superconductor material. The alloys can be made a by process that involves first rolling the alloy then annealing the alloy. A relatively large volume percentage of the alloy can be formed of grains having a biaxial or cube texture.

  6. Construction material

    DOE Patents [OSTI]

    Wagh, Arun S. (Orland Park, IL); Antink, Allison L. (Bolingbrook, IL)

    2008-07-22T23:59:59.000Z

    A structural material of a polystyrene base and the reaction product of the polystyrene base and a solid phosphate ceramic is applied as a slurry which includes one or more of a metal oxide or a metal hydroxide with a source of phosphate to produce a phosphate ceramic and a poly (acrylic acid or acrylate) or combinations or salts thereof and polystyrene or MgO applied to the polystyrene base and allowed to cure so that the dried aqueous slurry chemically bonds to the polystyrene base. A method is also disclosed of applying the slurry to the polystyrene base.

  7. Materials Science

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > The EnergyCenter (LMI-EFRC) -PublicationsMaterials Science

  8. Material Misfits

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)Integrated Codes |IsLove Your Home andDisposition | National NuclearMaterial Misfits

  9. Corrective Action Investigation Plan for Corrective Action Unit 168: Areas 25 and 26 Contaminated Materials and Waste Dumps, Nevada Test Site, Nevada (Rev. 0) includes Record of Technical Change No. 1 (dated 8/28/2002), Record of Technical Change No. 2 (dated 9/23/2002), and Record of Technical Change No. 3 (dated 6/2/2004)

    SciTech Connect (OSTI)

    U.S. Department of Energy, National Nuclear Security Administration Nevada

    2001-11-21T23:59:59.000Z

    This Corrective Action Investigation Plan contains the U.S. Department of Energy, National Nuclear Security Administration Nevada Operations Office's approach to collect data necessary to evaluate corrective action alternatives appropriate for the closure of Corrective Action Unit 168 under the Federal Facility Agreement and Consent Order. Corrective Action Unit 168 consists of a group of twelve relatively diverse Corrective Action Sites (CASs 25-16-01, Construction Waste Pile; 25-16-03, MX Construction Landfill; 25-19-02, Waste Disposal Site; 25-23-02, Radioactive Storage RR Cars; 25-23-18, Radioactive Material Storage; 25-34-01, NRDS Contaminated Bunker; 25-34-02, NRDS Contaminated Bunker; CAS 25-23-13, ETL - Lab Radioactive Contamination; 25-99-16, USW G3; 26-08-01, Waste Dump/Burn Pit; 26-17-01, Pluto Waste Holding Area; 26-19-02, Contaminated Waste Dump No.2). These CASs vary in terms of the sources and nature of potential contamination. The CASs are located and/or associated wit h the following Nevada Test Site (NTS) facilities within three areas. The first eight CASs were in operation between 1958 to 1984 in Area 25 include the Engine Maintenance, Assembly, and Disassembly Facility; the Missile Experiment Salvage Yard; the Reactor Maintenance, Assembly, and Disassembly Facility; the Radioactive Materials Storage Facility; and the Treatment Test Facility Building at Test Cell A. Secondly, the three CASs located in Area 26 include the Project Pluto testing area that operated from 1961 to 1964. Lastly, the Underground Southern Nevada Well (USW) G3 (CAS 25-99-16), a groundwater monitoring well located west of the NTS on the ridgeline of Yucca Mountain, was in operation during the 1980s. Based on site history and existing characterization data obtained to support the data quality objectives process, contaminants of potential concern (COPCs) for CAU 168 are primarily radionuclide; however, the COPCs for several CASs were not defined. To address COPC uncertainty, the analytical program for most CASs will include volatile organic compounds, semivolatile organic compounds, Resource Conservation and Recovery Act metals, total petroleum hydrocarbons, polychlorinated biphenyls, and radionuclides. Upon reviewing historical data and current site conditions, it has been determined that no further characterization is required at USW G3 (CAS 25-99-16) to select the appropriate corrective action. A cesium-137 source was encased in cement within the vadous zone during the drilling of the well (CAS 25-99-16). A corrective action of closure in place with a land-use restriction for drilling near USW G3 is appropriate. This corrective action will be documented in the Corrective Action Decision Document (CADD) for CAU 168. The results of the remaining field investigation will support a defensible evaluation of corrective action alternatives for the other CASs within CAU 168 in this CADD.

  10. PREFERRED WATERFLOOD MANAGEMENT PRACTICES FOR THE SPRABERRY TREND AREA

    SciTech Connect (OSTI)

    C. M. Sizemore; David S. Schechter

    2003-08-13T23:59:59.000Z

    This report describes the work performed during the second year of the project, ''Preferred Waterflood Management Practices for the Spraberry Trend Area''. The objective of this project is to significantly increase field-wide production in the Spraberry Trend in a short time frame through the application of preferred practices for managing and optimizing water injection. Our goal is to dispel negative attitudes and lack of confidence in water injection and to document the methodology and results for public dissemination to motivate waterflood expansion in the Spraberry Trend. To achieve this objective, in this period we concentrated our effort on characterization of Germania Unit using an analog field ET ODaniel unit and old cased hole neutron. Petrophysical Characterization of the Germania Spraberry units requires a unique approach for a number of reasons--limited core data, lack of modern log data and absence of directed studies within the unit. The need for characterization of the Germania unit has emerged as a first step in the review, understanding and enhancement of the production practices applicable within the unit and the trend area in general. In the absence or lack of the afore mentioned resources, an approach that will rely heavily on previous petrophysical work carried out in the neighboring ET O'Daniel unit (6.2 miles away), and normalization of the old log data prior to conventional interpretation techniques will be used. A log-based rock model has been able to guide successfully the prediction of pay and non-pay intervals within the ET O'Daniel unit, and will be useful if found applicable within the Germania unit. A novel multiple regression technique utilizing non-parametric transformations to achieve better correlations in predicting a dependent variable (permeability) from multiple independent variables (rock type, shale volume and porosity) will also be investigated in this study. A log data base includes digitized formats of Gamma Ray, Cased Hole Neutron, limited Resistivity and Neutron/Density/Sonic porosity logs over a considerable wide area. In addition, a progress report on GSU waterflood pilot is reported for this period. We have seen positive response of water injection on new wells. We believe by proper data acquisition and precise reservoir engineering techniques, any lack of confidence in waterflooding can be overcome. Therefore, we develop field management software to control a vast data from the pilot and to perform precise reservoir engineering techniques such as decline curve analysis, gas and oil material balances, bubble map plot and PVT analysis. The manual for this software is listed in the Appendix-A.

  11. Natural balance of graminicolous aphids in Pakistan. Survey of populations

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Natural balance of graminicolous aphids in Pakistan. Survey of populations Sulaiman HAMID Sind Sugar Industry Research Institute, 14-A, Latifabad III, Hyderabad Sind, Pakistan SUMMARY Aphids attacking gramineous crops were studied in seven climatically and ecologically different regions of Pakistan

  12. A unifying framework for watershed thermodynamics: balance equations for mass,

    E-Print Network [OSTI]

    Hassanizadeh, S. Majid

    A unifying framework for watershed thermodynamics: balance equations for mass, momentum, energy Hassanizadehb a Centre for Water Research, Department of Environmental Engineering, The University of Western Australia, 6907 Nedlands, Australia b Department of Water Management, Environmental and Sanitary Engineering

  13. Kalman filtering of IMU sensor for robot balance control

    E-Print Network [OSTI]

    Angelosanto, Gina (Gina C.)

    2008-01-01T23:59:59.000Z

    This study explores the use of Kalman filtering of measurements from an inertial measurement unit (IMU) to provide information on the orientation of a robot for balance control. A test bed was created to characterize the ...

  14. Relative efficiency of land surface energy balance components

    E-Print Network [OSTI]

    Bateni, S. M.

    [1] The partitioning of available energy into dissipative fluxes over land surfaces is dependent on the state variable of the surface energy balance (land surface temperature) and the state variable of the surface water ...

  15. Microsoft Word - Energy balancing rate settlement signals commitment...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Thursday, May 16, 2013 CONTACT: Doug Johnson, 503-230-5840 or 503-230-5131 Energy balancing rate settlement signals commitment to work on broader solutions Portland, Ore. - As...

  16. NITROGEN BALANCE IN INTENSIVE AGRICULTURE IN THE NORTH CHINA PLAIN

    E-Print Network [OSTI]

    Zhang, Yuming; Hu, Chunsheng; Zhang, Jiabao; Chen, Deli

    2009-01-01T23:59:59.000Z

    Chen DL, White RE, Chalk PM, Heng LK, Fisher R, Helyar KR.NIAES , 1994. pp. 209-234. Heng LK, White RE, Helyar KR,water balance (SWB) model (Heng et al. 2001) were conducted.

  17. Numerical balancing in a humidification dehumidification desalination system

    E-Print Network [OSTI]

    Miller, Jacob A., S.M. Massachusetts Institute of Technology

    2011-01-01T23:59:59.000Z

    This thesis details research on the thermal and concentration balancing of a humidification dehumidification desalination system. The system operates similarly to the natural rain cycle. Seawater is heated, sprayed into ...

  18. SEC Confidential Treatment Orders: Balancing Competing Regulatory Objectives

    E-Print Network [OSTI]

    Thompson, Anne Margaret

    2012-10-19T23:59:59.000Z

    This study examines how the Securities and Exchange Commission balances competing regulatory objectives in its decisions to approve requests to withhold proprietary information from firms' financial reports. The confidential treatment process...

  19. Work/Family Balance for Men in Student Affairs

    E-Print Network [OSTI]

    Singh, Shailendra Mohan

    2012-07-16T23:59:59.000Z

    This qualitative study will examine the concept of work/family demand specifically through the lens of male student affairs practitioners. Work family balance has been identified as a critical issue for the field of HRD impacting both individual...

  20. Soils Management, Site Productivity and Forest Nutrition: Nutrient Balance

    E-Print Network [OSTI]

    ;#12;1) principals 2) strategies 3) implementation Sustainable Soil Management: #12;- maintenance of fertility soil management Strategies: #12;Examples of adaptive management models used for achieving sustainableSoils Management, Site Productivity and Forest Nutrition: Nutrient Balance and Availability

  1. Introduction Dust aerosols affect visibility, perturb the radiative energy balance

    E-Print Network [OSTI]

    Wang, Jun

    Sunphotometer and air temperature from ground observations. Model Flow Chart GOES-8 06/28/00 1145 UTC -90 -80Introduction Dust aerosols affect visibility, perturb the radiative energy balance of the earth

  2. STANLEY WARNER'S CONTRIBUTIONS TO STATISTICALLY BALANCED INFORMATION TECHNOLOGY

    E-Print Network [OSTI]

    Federation? 3. Should the American Statistical Association adopt a program to certify statisticians? 4 Statistical Association, Stanley Warner first presented the issue of measuring the impact of advocacySTANLEY WARNER'S CONTRIBUTIONS TO STATISTICALLY BALANCED INFORMATION TECHNOLOGY Stephen E. Fienberg

  3. assembly line balancing: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    algorithms for time and space assembly line balancing Manuel Chica a,?, O Barcelona, Spain a r t i c l e i n f o Available online 1 June 2011 Keywords: Time and space assembly...

  4. acid-base balance: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    S. MITCHELL, T. T. GLEESON, California 92717 MITCHELL, G. S., T. T. GLEESON, AND A. F. BENNETT. Ventilation and acid-base balance during (Vcoz) and 02 consumption (SOL?), and...

  5. acid base balance: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    S. MITCHELL, T. T. GLEESON, California 92717 MITCHELL, G. S., T. T. GLEESON, AND A. F. BENNETT. Ventilation and acid-base balance during (Vcoz) and 02 consumption (SOL?), and...

  6. The decadal mean ocean circulation and Sverdrup balance

    E-Print Network [OSTI]

    Wunsch, Carl

    Elementary Sverdrup balance is tested in the context of the time-average of a 16-year duration time-varying ocean circulation estimate employing the great majority of global-scale data available between 1992 and 2007. The ...

  7. Triage: Balancing Energy and Quality of Service in a Microserver

    E-Print Network [OSTI]

    Ganesan, Deepak

    Triage: Balancing Energy and Quality of Service in a Microserver Nilanjan Banerjee Jacob Sorber and that copies bear this notice and the full citation on the first page. To copy otherwise, to republish, to post

  8. Update on adipocyte hormones - Regulation of energy balance and carbohydrate/lipid metabolism

    E-Print Network [OSTI]

    Havel, Peter J. D.V.M., Ph.D.

    2004-01-01T23:59:59.000Z

    ghrelin and the regulation of energy balance: a hypothalamicfree fatty acid. regulation of energy homeostasis is forfor leptin in the regulation of energy balance in humans (

  9. Photovoltaic Materials

    SciTech Connect (OSTI)

    Duty, C.; Angelini, J.; Armstrong, B.; Bennett, C.; Evans, B.; Jellison, G. E.; Joshi, P.; List, F.; Paranthaman, P.; Parish, C.; Wereszczak, A.

    2012-10-15T23:59:59.000Z

    The goal of the current project was to help make the US solar industry a world leader in the manufacture of thin film photovoltaics. The overall approach was to leverage ORNL’s unique characterization and processing technologies to gain a better understanding of the fundamental challenges for solar cell processing and apply that knowledge to targeted projects with industry members. ORNL has the capabilities in place and the expertise required to understand how basic material properties including defects, impurities, and grain boundaries affect the solar cell performance. ORNL also has unique processing capabilities to optimize the manufacturing process for fabrication of high efficiency and low cost solar cells. ORNL recently established the Center for Advanced Thin-film Systems (CATS), which contains a suite of optical and electrical characterization equipment specifically focused on solar cell research. Under this project, ORNL made these facilities available to industrial partners who were interested in pursuing collaborative research toward the improvement of their product or manufacturing process. Four specific projects were pursued with industrial partners: Global Solar Energy is a solar industry leader in full scale production manufacturing highly-efficient Copper Indium Gallium diSelenide (CIGS) thin film solar material, cells and products. ORNL worked with GSE to develop a scalable, non-vacuum, solution technique to deposit amorphous or nanocrystalline conducting barrier layers on untextured stainless steel substrates for fabricating high efficiency flexible CIGS PV. Ferro Corporation’s Electronic, Color and Glass Materials (“ECGM”) business unit is currently the world’s largest supplier of metallic contact materials in the crystalline solar cell marketplace. Ferro’s ECGM business unit has been the world's leading supplier of thick film metal pastes to the crystalline silicon PV industry for more than 30 years, and has had operational cells and modules in the field for 25 years. Under this project, Ferro leveraged world leading analytical capabilities at ORNL to characterize the paste-to-silicon interface microstructure and develop high efficiency next generation contact pastes. Ampulse Corporation is developing a revolutionary crystalline-silicon (c-Si) thin-film solar photovoltaic (PV) technology. Utilizing uniquely-textured substrates and buffer materials from the Oak Ridge National Laboratory (ORNL), and breakthroughs in Hot-Wire Chemical Vapor Deposition (HW-CVD) techniques in epitaxial silicon developed at the National Renewable Energy Laboratory (NREL), Ampulse is creating a solar technology that is tunable in silicon thickness, and hence in efficiency and economics, to meet the specific requirements of multiple solar PV applications. This project focused on the development of a high rate deposition process to deposit Si, Ge, and Si1-xGex films as an alternate to hot-wire CVD. Mossey Creek Solar is a start-up company with great expertise in the solar field. The primary interest is to create and preserve jobs in the solar sector by developing high-yield, low-cost, high-efficiency solar cells using MSC-patented and -proprietary technologies. The specific goal of this project was to produce large grain formation in thin, net-shape-thickness mc-Si wafers processed with high-purity silicon powder and ORNL's plasma arc lamp melting without introducing impurities that compromise absorption coefficient and carrier lifetime. As part of this project, ORNL also added specific pieces of equipment to enhance our ability to provide unique insight for the solar industry. These capabilities include a moisture barrier measurement system, a combined physical vapor deposition and sputtering system dedicated to cadmium-containing deposits, adeep level transient spectroscopy system useful for identifying defects, an integrating sphere photoluminescence system, and a high-speed ink jet printing system. These tools were combined with others to study the effect of defects on the performance of crystalline silicon and

  10. A network model of parametric working memory. Supplementary Material

    E-Print Network [OSTI]

    Brody, Carlos

    obeys the current balance equation: CM dVi dt = -gL [Vi - VL]-gESE,i [Vi - VE]-gISI,i [Vi - VIA network model of parametric working memory. Supplementary Material Paul Miller1 , Carlos D Brody2

  11. Supplementary material Boundary conditions and numerical solution of Equation 4

    E-Print Network [OSTI]

    Neufeld, Jerome A.

    Supplementary Material for Particle Mass Yield from -Caryophyllene Ozonolysis Qi Chen1 , Yongjie Li in a continuously mixed flow reactor (CMFR) The mass balance of organic aerosol in a CMFR is described by the following equation: org, CMFR org, inflow org, CMFR org org, CMFR CMFR CMFR dM M M F M dt = - + - (A1

  12. Balancing Operation for the Optimization of Hydronic Networks

    E-Print Network [OSTI]

    Couillaud, N.; Riederer, P.; Jandon, M.; Diab, Y.

    2005-01-01T23:59:59.000Z

    of these simulations are the evaluation of: • the application costs of balancing method, • energy consumptions of the heating system (pump & boiler), • thermal comfort in building zones, • The global costs of the heating system. ANALYSIS OF RESULTS..., Paris, 14/15 October 2004. [5] Couillaud N. #2, Bernadou E., Georges B., Riederer P., A virtual bench to test the performance and balancing of hydronic networks, 6th International Conference, Energy for Buildings, Vilnius, Lithuania, October 2004...

  13. Balancing of high speed, flexible rotating shafts across critical speeds 

    E-Print Network [OSTI]

    White, Gary Paul

    1977-01-01T23:59:59.000Z

    BALANCING OF HIGH SPEED, FLEXIBLE ROTATING SHAFTS ACROSS CRITICAL SPEEDS A Thesis by Gary Paul White Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE... August 1977 Major Subject: Mechanical Engineering Gary Paul White 1977 BALANCING OF HIGH SPEED, FLEXIBLE ROTATING SHAFTS ACROSS CRITICAL SPEEDS A Thesis by GARY PAUL WHITE Approved as to style and content by: Head of Department Member August...

  14. Next Generation Nuclear Plant Materials Research and Development Program Plan

    SciTech Connect (OSTI)

    G.O. Hayner; R.L. Bratton; R.N. Wright

    2005-09-01T23:59:59.000Z

    The U.S Department of Energy (DOE) has selected the Very High Temperature Reactor (VHTR) design for the Next Generation Nuclear Plant (NGNP) Project. The NGNP will demonstrate the use of nuclear power for electricity and hydrogen production without greenhouse gas emissions. The reactor design will be a graphite moderated, helium-cooled, prismatic or pebble-bed, thermal neutron spectrum reactor that will produce electricity and hydrogen in a state-of-the-art thermodynamically efficient manner. The NGNP will use very high burn-up, low-enriched uranium, TRISO-coated fuel and have a projected plant design service life of 60 years. The VHTR concept is considered to be the nearest-term reactor design that has the capability to efficiently produce hydrogen. The plant size, reactor thermal power, and core configuration will ensure passive decay heat removal without fuel damage or radioactive material releases during accidents. The NGNP Project is envisioned to demonstrate the following: (1) A full-scale prototype VHTR by about 2021; (2) High-temperature Brayton Cycle electric power production at full scale with a focus on economic performance; (3) Nuclear-assisted production of hydrogen (with about 10% of the heat) with a focus on economic performance; and (4) By test, the exceptional safety capabilities of the advanced gas-cooled reactors. Further, the NGNP program will: (1) Obtain a Nuclear Regulatory Commission (NRC) License to construct and operate the NGNP, this process will provide a basis for future performance based, risk-informed licensing; and (2) Support the development, testing, and prototyping of hydrogen infrastructures. The NGNP Materials Research and Development (R&D) Program is responsible for performing R&D on likely NGNP materials in support of the NGNP design, licensing, and construction activities. The NGNP Materials R&D Program includes the following elements: (1) Developing a specific approach, program plan and other project management tools for managing the R&D program elements; (2) Developing a specific work package for the R&D activities to be performed during each government fiscal year; (3) Reporting the status and progress of the work based on committed deliverables and milestones; (4) Developing collaboration in areas of materials R&D of benefit to the NGNP with countries that are a part of the Generation IV International Forum; and (5) Ensuring that the R&D work performed in support of the materials program is in conformance with established Quality Assurance and procurement requirements. The objective of the NGNP Materials R&D Program is to provide the essential materials R&D needed to support the design and licensing of the reactor and balance of plant, excluding the hydrogen plant. The materials R&D program is being initiated prior to the design effort to ensure that materials R&D activities are initiated early enough to support the design process and support the Project Integrator. The thermal, environmental, and service life conditions of the NGNP will make selection and qualification of some high-temperature materials a significant challenge; thus, new materials and approaches may be required.

  15. Comparative material balances around pretreatment technologies for the conversion of switchgrass to soluble sugars

    E-Print Network [OSTI]

    California at Riverside, University of

    . Bioethanol is one of the pos- sible renewable alternatives to liquid fossil fuels. The majority of current

  16. A quadratic cumulative production model for the material balance of an abnormally pressured gas reservoir 

    E-Print Network [OSTI]

    Gonzalez, Felix Eduardo

    2005-02-17T23:59:59.000Z

    for the case of an abnormally-pressured gas reservoir. The primary assumption in this derivation is that WGp <1 or Ce(p)(pi-p)<1. Further, we can proceed by assuming that W is either constant or some arbitrary function. If we assume W...

  17. Velocity models, material balance and solution convergence in streamline-based simulation

    E-Print Network [OSTI]

    Sabir, Kamran

    2002-01-01T23:59:59.000Z

    of {x, y, z) to a unit cube in the pseudo space of (a, P, y). This code also determines the velocity models, and sketches the streamlines in the domain. Calculation of time of flight is also incorporated in the code. Another code was written... be obtained from the velocity components. 2. 2 Five-Spot Waterflooding Pattern Morel-Seytoux shows that the following are the potential (P) and stream (r[r) functions for five-spot waterflooding pattern (quarter five-spot symmetry element): ] 1 ? rn[4x...

  18. A quadratic cumulative production model for the material balance of an abnormally pressured gas reservoir

    E-Print Network [OSTI]

    Gonzalez, Felix Eduardo

    2005-02-17T23:59:59.000Z

    3.18 Plot of pp p dGGG 0 1)/? ( ?? vs. G p ? Case 3. ....................................................... 43 3.19 Plot of ? ? ? ? ? ? ? ? ? ? pp p dG G Gzp )/? (0 1)/? ( vs. G p ? Case 3. .............................................. 44 3...

  19. Integration and quantification of uncertainty of volumetric and material balance analyses using a Bayesian framework

    E-Print Network [OSTI]

    Ogele, Chile

    2005-11-01T23:59:59.000Z

    ......................................... 13 Example 1: Gas-cap Oil Reservoir Reported by Dake ................... 13 Case 1: Large Uncertainty in Prior and Small Uncertainty in Pressure Data .............................................................................. 13 Case 2... OHIP and quantify uncertainty. Test the framework using data for gas-cap oil reservoirs reported in the literature. 2. Investigate the effect of correlation between parameters of the prior distribution on the combined OHIP estimate. General...

  20. Key Elements of and Materials Performance Targets for Highly Insulating Window Frames

    SciTech Connect (OSTI)

    Gustavsen, Arild; Grynning, Steinar; Arasteh, Dariush; Jelle, Bjorn Petter; Goudey, Howdy

    2011-03-28T23:59:59.000Z

    The thermal performance of windows is important for energy efficient buildings. Windows typically account for about 30-50 percent of the transmission losses though the building envelope, even if their area fraction of the envelope is far less. The reason for this can be found by comparing the thermal transmittance (U-factor) of windows to the U-factor of their opaque counterparts (wall, roof and floor constructions). In well insulated buildings the U-factor of walls, roofs an floors can be between 0.1-0.2 W/(m2K). The best windows have U-values of about 0.7-1.0. It is therefore obvious that the U-factor of windows needs to be reduced, even though looking at the whole energy balance for windows (i.e. solar gains minus transmission losses) makes the picture more complex.In high performance windows the frame design and material use is of utmost importance, as the frame performance is usually the limiting factor for reducing the total window U-factor further. This paper describes simulation studies analyzing the effects on frame and edge-of-glass U-factors of different surface emissivities as well as frame material and spacer conductivities. The goal of this work is to define materials research targets for window frame components that will result in better frame thermal performance than is exhibited by the best products available on the market today.

  1. Materials Characterization | Advanced Materials | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHighand Retrievals from a New 183-GHzMAR Os2010Material Safety Electron

  2. Critical Materials Institute

    SciTech Connect (OSTI)

    Alex King

    2013-01-09T23:59:59.000Z

    Ames Laboratory Director Alex King talks about the goals of the Critical Materials Institute in diversifying the supply of critical materials, developing substitute materials, developing tools and techniques for recycling critical materials, and forecasting materials needs to avoid future shortages.

  3. Critical Materials Institute

    ScienceCinema (OSTI)

    Alex King

    2013-06-05T23:59:59.000Z

    Ames Laboratory Director Alex King talks about the goals of the Critical Materials Institute in diversifying the supply of critical materials, developing substitute materials, developing tools and techniques for recycling critical materials, and forecasting materials needs to avoid future shortages.

  4. HAZARDOUS MATERIALS INCIDENTS What are hazardous materials?

    E-Print Network [OSTI]

    Fernandez, Eduardo

    HAZARDOUS MATERIALS INCIDENTS What are hazardous materials? Hazardous materials are chemicals, accidentally spilled, or released. In addition to laboratory chemicals, hazardous materials may include common not involve highly toxic or noxious hazardous materials, a fire, or an injury requiring medical attention

  5. CEES - Focus Areas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    reactivity. These approaches, enabled by the Center's deep cross-cutting capabilities of characterization, theory and materials synthesis, will lead to new approaches to control...

  6. ICME & MGI Big Area Additive Manufacturing

    E-Print Network [OSTI]

    ICME & MGI · Big Area Additive Manufacturing · Neutron Characterization for AM · Materials problems in additive manu- facturing (AM). Additive manufacturing, or three-dimensional (3-D) printing of the world's most advanced neu- tron facilities, the HFIR and SNS, to characterize additive manufactured

  7. The United States Plutonium Balance, 1944 - 2009

    SciTech Connect (OSTI)

    none,

    2012-06-01T23:59:59.000Z

    This report updates the report -Plutonium: The first 50 years- which was released by the U.S.Department of Energy (DOE) in 1996. The topic of both reports is plutonium, sometimes referred to as Pu-239, which is capable of sustaining a nuclear chain reaction and is used in nuclear weapons and for nuclear power production. This report updates 1994 data through 2009. The four most significant changes since 1994 include: (a) the completion of cleanup activities at the Rocky Flats Plant in 2005; (b) material consolidation and disposition activities, especially shipments from Hanford to the Savannah River Site; (c) the 2007 declaration of an additional 9.0 MT of weapons grade plutonium to be surplus to defense needs in the coming decades; and (d) the opening of the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico in 1999.

  8. Groundwater Management Areas (Texas)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the Texas Commission on Environmental Quality and the Texas Water Development Board to establish Groundwater Management Areas to provide for the conservation,...

  9. Riparian Area. . . . . . . . . . . . . . . . . . . . Management Handbook

    E-Print Network [OSTI]

    Balasundaram, Balabhaskar "Baski"

    ..............................................................................................................19 Bruce Hoagland, Oklahoma Biological Survey and the University of Oklahoma Forest Management Riparian Area. . . . . . . . . . . . . . . . . . . . Management Handbook E-952 Oklahoma Cooperative . . . . . . . . . . . . . Oklahoma Conservation Commission Management Handbook #12

  10. The study of material accountancy procedures for uranium in a whole nuclear fuel cycle

    SciTech Connect (OSTI)

    Nakano, Hiromasa; Akiba, Mitsunori [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

    1995-07-01T23:59:59.000Z

    Material accountancy procedures for uranium under a whole nuclear fuel cycle were studied by taking into consideration the material accountancy capability associated with realistic measurement uncertainties. The significant quantity used by the International Atomic Energy Agency (IAEA) for low-enriched uranium is 75 kg U-235 contained. A loss of U-235 contained in uranium can be detected by either of the following two procedures: one is a traditional U-235 isotope balance, and the other is a total uranium element balance. Facility types studied in this paper were UF6 conversion, gas centrifuge uranium enrichment, fuel fabrication, reprocessing, plutonium conversion, and MOX fuel production in Japan, where recycled uranium is processed in addition to natural uranium. It was found that the material accountancy capability of a total uranium element balance was almost always higher than that of a U-235 isotope balance under normal accuracy of weight, concentration, and enrichment measurements. Changing from the traditional U-235 isotope balance to the total uranium element balance for these facilities would lead to a gain of U-235 loss detection capability through material accountancy and to a reduction in the required resources of both the IAEA and operators.

  11. Advanced Materials for Reversible Solid Oxide Fuel Cell (RSOFC...

    Broader source: Energy.gov (indexed) [DOE]

    RSOFC cell stack technology in the areas of durability and performance, via- - materials development, and - stack design & development. f To meet the following performance...

  12. MATERIALS MANAGEMENT MATERIALS MANAGEMENT -INVENTORY CONTROL

    E-Print Network [OSTI]

    Oliver, Douglas L.

    MATERIALS MANAGEMENT MATERIALS MANAGEMENT - INVENTORY CONTROL Record of Property Transferred from ______ ___________________________________ 2. DEAN (If Applies) ______ ___________________________________ 5. UNIVERSITY DIRECTOR OF MATERIALS MANAGEMENT ______ ___________________________________ 3. HOSPITAL DIRECTOR (If Applies) ______ IF YOU NEED

  13. Nuclear Material Control and Accountability System Effectiveness Tool (MSET)

    SciTech Connect (OSTI)

    Powell, Danny H [ORNL] [ORNL; Elwood Jr, Robert H [ORNL] [ORNL; Roche, Charles T [ORNL] [ORNL; Campbell, Billy J [ORNL] [ORNL; Hammond, Glenn A [ORNL] [ORNL; Meppen, Bruce W [ORNL] [ORNL; Brown, Richard F [ORNL] [ORNL

    2011-01-01T23:59:59.000Z

    A nuclear material control and accountability (MC&A) system effectiveness tool (MSET) has been developed in the United States for use in evaluating material protection, control, and accountability (MPC&A) systems in nuclear facilities. The project was commissioned by the National Nuclear Security Administration's Office of International Material Protection and Cooperation. MSET was developed by personnel with experience spanning more than six decades in both the U.S. and international nuclear programs and with experience in probabilistic risk assessment (PRA) in the nuclear power industry. MSET offers significant potential benefits for improving nuclear safeguards and security in any nation with a nuclear program. MSET provides a design basis for developing an MC&A system at a nuclear facility that functions to protect against insider theft or diversion of nuclear materials. MSET analyzes the system and identifies several risk importance factors that show where sustainability is essential for optimal performance and where performance degradation has the greatest impact on total system risk. MSET contains five major components: (1) A functional model that shows how to design, build, implement, and operate a robust nuclear MC&A system (2) A fault tree of the operating MC&A system that adapts PRA methodology to analyze system effectiveness and give a relative risk of failure assessment of the system (3) A questionnaire used to document the facility's current MPC&A system (provides data to evaluate the quality of the system and the level of performance of each basic task performed throughout the material balance area [MBA]) (4) A formal process of applying expert judgment to convert the facility questionnaire data into numeric values representing the performance level of each basic event for use in the fault tree risk assessment calculations (5) PRA software that performs the fault tree risk assessment calculations and produces risk importance factor reports on the facility's MC&A (software widely used in the aerospace, chemical, and nuclear power industries) MSET was peer reviewed in 2007 and validated in 2008 by benchmark testing at the Idaho National Laboratory in the United States. The MSET documents were translated into Russian and provided to Rosatom in July of 2008, and MSET is currently being evaluated for potential application in Russian Nuclear Facilities.

  14. Gas storage materials, including hydrogen storage materials

    DOE Patents [OSTI]

    Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

    2014-11-25T23:59:59.000Z

    A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material, such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

  15. Gas storage materials, including hydrogen storage materials

    DOE Patents [OSTI]

    Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

    2013-02-19T23:59:59.000Z

    A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

  16. Summary Leaf area index (LAI) is a key biophysical vari-able in most process-based forest-ecosystem models. How-

    E-Print Network [OSTI]

    Minnesota, University of

    the Ad- vanced Very High Resolution Radiometer (AVHRR) satel- lite-borne sensor of surface greenness). Because of the strong influence of leaf area on rates of canopy gas ex- change and energy balance, efforts

  17. Functional Materials for Energy | Advanced Materials | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Storage Fuel Cells Thermoelectrics Separations Materials Catalysis Sensor Materials Polymers and Composites Carbon Fiber Related Research Chemistry and Physics at...

  18. Geothermal br Resource br Area Geothermal br Resource br Area...

    Open Energy Info (EERE)

    Zone Mesozoic granite granodiorite Aurora Geothermal Area Aurora Geothermal Area Walker Lane Transition Zone Geothermal Region MW Beowawe Hot Springs Geothermal Area Beowawe Hot...

  19. Energy Balance in Wireless Networks Using Connection Segmentation and Range Control

    E-Print Network [OSTI]

    Simha, Rahul

    Energy Balance in Wireless Networks Using Connection Segmentation and Range Control Nitin Kumar are optimized to balance energy consumption across the network. This paper formulates an en­ ergy balance­ nalized for their important role in network operation. While route selection to balance energy [13], [31

  20. Author's personal copy Energy and water balance of two contrasting loblolly pine plantations on the

    E-Print Network [OSTI]

    Noormets, Asko

    Author's personal copy Energy and water balance of two contrasting loblolly pine plantations are more interested in water and carbon balances, quantifying forest energy balance offers insights to how Accepted 9 September 2009 Keywords: Energy balance Evapotranspiration Forest albedo Forest hydrology

  1. Modularization and simulation techniques for heat balance-based energy and load calculation

    E-Print Network [OSTI]

    Richard K. Strand

    2001-01-01T23:59:59.000Z

    the Loads Toolkit research project is to obtain a heat balance based load calculation procedure that

  2. Abstract --In electromagnetic applications, hysteresis phenomena in magnetic materials are responsible of

    E-Print Network [OSTI]

    Boyer, Edmond

    rotation. Furthermore, based on the balance of chemical equation analogies, this model has the advantage13. M M Abstract -- In electromagnetic applications, hysteresis phenomena in magnetic materials the implementation proceeding used for some hysteresis material models and how they are applied in a sensor study

  3. Nuclear weapons. The balance of terror, the quest for peace

    SciTech Connect (OSTI)

    Edwards, A.J.C.

    1985-01-01T23:59:59.000Z

    This book provides a study from first principles of nuclear strategy and the balance of terror. This book addresses the most fundamental issues of our time - what is the balance of terror. How did it come to be. Is it necessary. How has it affected world politics. Will it keep the world at peace. Is it stable in an intrinsic and a dynamic sense. How real a threat is a first strike advantage. What can arms control agreements contribute. What should the objectives of such agreements be. How might a nuclear conflict begin. What would be the chance of containing such a conflict once begun. What are the advantages and disadvantages of the balance of terror. Are there any alternatives to a balance of terror, such as general or nuclear disarmament, which would be both attainable and preferable. If not, what can be done to make a better balance of terror. What are the main threats to stability. What should the West's policies be. What role is there for the independent nuclear deterrents of smaller countries. And how have recent developments such as the American 'star-wars' programme and the 'nuclear winter' hypothesis affected the answers to all these questions.

  4. Improved flywheel materials : characterization of nanofiber modified flywheel test specimen.

    SciTech Connect (OSTI)

    Boyle, Timothy J.; Bell, Nelson Simmons; Ehlen, Mark Andrew; Anderson, Benjamin John; Miller, William Kenneth

    2013-09-01T23:59:59.000Z

    As alternative energy generating devices (i.e., solar, wind, etc) are added onto the electrical energy grid (AC grid), irregularities in the available electricity due to natural occurrences (i.e., clouds reducing solar input or wind burst increasing wind powered turbines) will be dramatically increased. Due to their almost instantaneous response, modern flywheel-based energy storage devices can act a mechanical mechanism to regulate the AC grid; however, improved spin speeds will be required to meet the necessary energy levels to balance thesegreen' energy variances. Focusing on composite flywheels, we have investigated methods for improving the spin speeds based on materials needs. The so-called composite flywheels are composed of carbon fiber (C-fiber), glass fiber, and aglue' (resin) to hold them together. For this effort, we have focused on the addition of fillers to the resin in order to improve its properties. Based on the high loads required for standard meso-sized fillers, this project investigated the utility of ceramic nanofillers since they can be added at very low load levels due to their high surface area. The impact that TiO2 nanowires had on the final strength of the flywheel material was determined by athree-point-bend' test. The results of the introduction of nanomaterials demonstrated an increase instrength' of the flywheel's C-fiber-resin moiety, with an upper limit of a 30% increase being reported. An analysis of the economic impact concerning the utilization of the nanowires was undertaken and after accounting for new-technology and additional production costs, return on improved-nanocomposite investment was approximated at 4-6% per year over the 20-year expected service life. Further, it was determined based on the 30% improvement in strength, this change may enable a 20-30% reduction in flywheel energy storage cost (%24/kW-h).

  5. Radiation shielding materials and containers incorporating same

    DOE Patents [OSTI]

    Mirsky, Steven M. (Greenbelt, MD); Krill, Stephen J. (Arlington, VA); Murray, Alexander P. (Gaithersburg, MD)

    2005-11-01T23:59:59.000Z

    An improved radiation shielding material and storage systems for radioactive materials incorporating the same. The PYRolytic Uranium Compound ("PYRUC") shielding material is preferably formed by heat and/or pressure treatment of a precursor material comprising microspheres of a uranium compound, such as uranium dioxide or uranium carbide, and a suitable binder. The PYRUC shielding material provides improved radiation shielding, thermal characteristic, cost and ease of use in comparison with other shielding materials. The shielding material can be used to form containment systems, container vessels, shielding structures, and containment storage areas, all of which can be used to house radioactive waste. The preferred shielding system is in the form of a container for storage, transportation, and disposal of radioactive waste. In addition, improved methods for preparing uranium dioxide and uranium carbide microspheres for use in the radiation shielding materials are also provided.

  6. Radiation Shielding Materials and Containers Incorporating Same

    DOE Patents [OSTI]

    Mirsky, Steven M.; Krill, Stephen J.; and Murray, Alexander P.

    2005-11-01T23:59:59.000Z

    An improved radiation shielding material and storage systems for radioactive materials incorporating the same. The PYRolytic Uranium Compound (''PYRUC'') shielding material is preferably formed by heat and/or pressure treatment of a precursor material comprising microspheres of a uranium compound, such as uranium dioxide or uranium carbide, and a suitable binder. The PYRUC shielding material provides improved radiation shielding, thermal characteristic, cost and ease of use in comparison with other shielding materials. The shielding material can be used to form containment systems, container vessels, shielding structures, and containment storage areas, all of which can be used to house radioactive waste. The preferred shielding system is in the form of a container for storage, transportation, and disposal of radioactive waste. In addition, improved methods for preparing uranium dioxide and uranium carbide microspheres for use in the radiation shielding materials are also provided.

  7. Materials Project: A Materials Genome Approach

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Ceder, Gerbrand (MIT); Persson, Kristin (LBNL)

    Technological innovation - faster computers, more efficient solar cells, more compact energy storage - is often enabled by materials advances. Yet, it takes an average of 18 years to move new materials discoveries from lab to market. This is largely because materials designers operate with very little information and must painstakingly tweak new materials in the lab. Computational materials science is now powerful enough that it can predict many properties of materials before those materials are ever synthesized in the lab. By scaling materials computations over supercomputing clusters, this project has computed some properties of over 80,000 materials and screened 25,000 of these for Li-ion batteries. The computations predicted several new battery materials which were made and tested in the lab and are now being patented. By computing properties of all known materials, the Materials Project aims to remove guesswork from materials design in a variety of applications. Experimental research can be targeted to the most promising compounds from computational data sets. Researchers will be able to data-mine scientific trends in materials properties. By providing materials researchers with the information they need to design better, the Materials Project aims to accelerate innovation in materials research.[copied from http://materialsproject.org/about] You will be asked to register to be granted free, full access.

  8. Greenhouse gas balances of biomass energy systems

    SciTech Connect (OSTI)

    Marland, G. [Oak Ridge National Lab., TN (United States); Schlamadinger, B. [Institute for Energy Research, Joanneum Research, Graz, (Austria)

    1994-12-31T23:59:59.000Z

    A full energy-cycle analysis of greenhouse gas emissions of biomass energy systems requires analysis well beyond the energy sector. For example, production of biomass fuels impacts on the global carbon cycle by altering the amount of carbon stored in the biosphere and often by producing a stream of by-products or co-products which substitute for other energy-intensive products like cement, steel, concrete or, in case of ethanol from corn, animal feed. It is necessary to distinguish between greenhouse gas emissions associated with the energy product as opposed to those associated with other products. Production of biomass fuels also has an opportunity cost because it uses large land areas which could have been used otherwise. Accounting for the greenhouse gas emissions from biomass fuels in an environment of credits and debits creates additional challenges because there are large nonlinearities in the carbon flows over time. This paper presents some of the technical challenges of comprehensive greenhouse gas accounting and distinguishes between technical and public policy issues.

  9. VALIDATION OF NUCLEAR MATERIAL CONTROL AND ACCOUNTABILITY (MC&A) SYSTEM EFFECTIVENESS TOOL (MSET) AT IDAHO NATIONAL LABORATORY (INL)

    SciTech Connect (OSTI)

    Meppen, Bruce; Haga, Roger; Moedl, Kelley; Bean, Tom; Sanders, Jeff; Thom, Mary Alice

    2008-07-01T23:59:59.000Z

    A Nuclear Material Control and Accountability (MC&A) Functional Model has been developed to describe MC&A systems at facilities possessing Category I or II Special Nuclear Material (SNM). Emphasis is on achieving the objectives of 144 “Fundamental Elements” in key areas ranging from categorization of nuclear material to establishment of Material Balance Areas (MBAs), controlling access, performing quality measurements of inventories and transfers, timely reporting all activities, and detecting and investigating anomalies. An MC&A System Effectiveness Tool (MSET), including probabilistic risk assessment (PRA) technology for evaluating MC&A effectiveness and relative risk, has been developed to accompany the Functional Model. The functional model and MSET were introduced at the 48th annual International Nuclear Material Management (INMM) annual meeting in July, 20071,2. A survey/questionnaire is used to accumulate comprehensive data regarding the MC&A elements at a facility. Data is converted from the questionnaire to numerical values using the DELPHI method and exercises are conducted to evaluate the overall effectiveness of an MC&A system. In 2007 a peer review was conducted and a questionnaire was completed for a hypothetical facility and exercises were conducted. In the first quarter of 2008, a questionnaire was completed at Idaho National Laboratory (INL) and MSET exercises were conducted. The experience gained from conducting the MSET exercises at INL helped evaluate the completeness and consistency of the MC&A Functional Model, descriptions of fundamental elements of the MC&A Functional Model, relationship between the MC&A Functional Model and the MC&A PRA tool and usefulness of the MSET questionnaire data collection process.

  10. Puget Sound Area Electric Reliability Plan : Draft Environmental Impact State.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    1991-09-01T23:59:59.000Z

    The Puget Sound Area Electric Reliability Plan Draft Environmental Impact Statement (DEIS) identifies the alternatives for solving a power system problem in the Puget Sound area. This Plan is undertaken by Bonneville Power Administration (BPA), Puget Sound Power Light, Seattle City Light, Snohomish Public Utility District No. 1 (PUD), and Tacoma Public Utilities. The Plan consists of potential actions in Puget Sound and other areas in the State of Washington. A specific need exists in the Puget Sound area for balance between east-west transmission capacity and the increasing demand to import power generated east of the Cascades. At certain times of the year, there is more demand for power than the electric system can supply in the Puget Sound area. This high demand, called peak demand, occurs during the winter months when unusually cold weather increases electricity use for heating. The existing power system can supply enough power if no emergencies occur. However, during emergencies, the system will not operate properly. As demand grows, the system becomes more strained. To meet demand, the rate of growth of demand must be reduced or the ability to serve the demand must be increased, or both. The plan to balance Puget Sound's power demand and supply has these purposes: The plan should define a set of actions that would accommodate ten years of load growth (1994--2003). Federal and State environmental quality requirements should be met. The plan should be consistent with the plans of the Northwest Power Planning Council. The plan should serve as a consensus guideline for coordinated utility action. The plan should be flexible to accommodate uncertainties and differing utility needs. The plan should balance environmental impacts and economic costs. The plan should provide electric system reliability consistent with customer expectations. 29 figs., 24 tabs.

  11. Puget Sound area electric reliability plan. Draft environmental impact statement

    SciTech Connect (OSTI)

    Not Available

    1991-09-01T23:59:59.000Z

    The Puget Sound Area Electric Reliability Plan Draft Environmental Impact Statement (DEIS) identifies the alternatives for solving a power system problem in the Puget Sound area. This Plan is undertaken by Bonneville Power Administration (BPA), Puget Sound Power & Light, Seattle City Light, Snohomish Public Utility District No. 1 (PUD), and Tacoma Public Utilities. The Plan consists of potential actions in Puget Sound and other areas in the State of Washington. A specific need exists in the Puget Sound area for balance between east-west transmission capacity and the increasing demand to import power generated east of the Cascades. At certain times of the year, there is more demand for power than the electric system can supply in the Puget Sound area. This high demand, called peak demand, occurs during the winter months when unusually cold weather increases electricity use for heating. The existing power system can supply enough power if no emergencies occur. However, during emergencies, the system will not operate properly. As demand grows, the system becomes more strained. To meet demand, the rate of growth of demand must be reduced or the ability to serve the demand must be increased, or both. The plan to balance Puget Sound`s power demand and supply has these purposes: The plan should define a set of actions that would accommodate ten years of load growth (1994--2003). Federal and State environmental quality requirements should be met. The plan should be consistent with the plans of the Northwest Power Planning Council. The plan should serve as a consensus guideline for coordinated utility action. The plan should be flexible to accommodate uncertainties and differing utility needs. The plan should balance environmental impacts and economic costs. The plan should provide electric system reliability consistent with customer expectations. 29 figs., 24 tabs.

  12. Materials for solid state lighting

    SciTech Connect (OSTI)

    Johnson, S.G.; Simmons, J.A.

    2002-03-26T23:59:59.000Z

    Dramatic improvement in the efficiency of inorganic and organic light emitting diodes (LEDs and OLEDs) within the last decade has made these devices viable future energy efficient replacements for current light sources. However, both technologies must overcome major technical barriers, requiring significant advances in material science, before this goal can be achieved. Attention will be given to each technology associated with the following major areas of material research: (1) material synthesis, (2) process development, (3) device and defect physics, and (4) packaging. The discussion on material synthesis will emphasize the need for further development of component materials, including substrates and electrodes, necessary for improving device performance. The process technology associated with the LEDs and OLEDs is very different, but in both cases it is one factor limiting device performance. Improvements in process control and methodology are expected to lead to additional benefits of higher yield, greater reliability and lower costs. Since reliability and performance are critical to these devices, an understanding of the basic physics of the devices and device failure mechanisms is necessary to effectively improve the product. The discussion will highlight some of the more basic material science problems remaining to be solved. In addition, consideration will be given to packaging technology and the need for the development of novel materials and geometries to increase the efficiencies and reliability of the devices. The discussion will emphasize the performance criteria necessary to meet lighting applications, in order to illustrate the gap between current status and market expectations for future product.

  13. Energy balance for uranium recovery from seawater

    SciTech Connect (OSTI)

    Schneider, E.; Lindner, H. [The University of Texas, 1 University Station C2200, Austin, TX 78712 (United States)

    2013-07-01T23:59:59.000Z

    The energy return on investment (EROI) of an energy resource is the ratio of the energy it ultimately produces to the energy used to recover it. EROI is a key viability measure for a new recovery technology, particularly in its early stages of development when financial cost assessment would be premature or highly uncertain. This paper estimates the EROI of uranium recovery from seawater via a braid adsorbent technology. In this paper, the energy cost of obtaining uranium from seawater is assessed by breaking the production chain into three processes: adsorbent production, adsorbent deployment and mooring, and uranium elution and purification. Both direct and embodied energy inputs are considered. Direct energy is the energy used by the processes themselves, while embodied energy is used to fabricate their material, equipment or chemical inputs. If the uranium is used in a once-through fuel cycle, the braid adsorbent technology EROI ranges from 12 to 27, depending on still-uncertain performance and system design parameters. It is highly sensitive to the adsorbent capacity in grams of U captured per kg of adsorbent as well as to potential economies in chemical use. This compares to an EROI of ca. 300 for contemporary terrestrial mining. It is important to note that these figures only consider the mineral extraction step in the fuel cycle. At a reference performance level of 2.76 g U recovered per kg adsorbent immersed, the largest energy consumers are the chemicals used in adsorbent production (63%), anchor chain mooring system fabrication and operations (17%), and unit processes in the adsorbent production step (12%). (authors)

  14. MATERIALS MANAGEMENT MATERIALS MANAGEMENT -INVENTORY CONTROL

    E-Print Network [OSTI]

    Oliver, Douglas L.

    MATERIALS MANAGEMENT MATERIALS MANAGEMENT - INVENTORY CONTROL NOTICE OF DESIGNATED DEPARTMENTAL OF MATERIALS MANAGEMENT ______ FURTHER INSTRUCTIONS 1. Include a copy of any relevant documents. 2. Item MATERIALS COORDINATOR ­ IC-8 Mail, Fax or PDF the entire package to: MC 2010 Fax: 679-4240 REFERENCE # DMC

  15. Storage containers for radioactive material

    DOE Patents [OSTI]

    Groh, E.F.; Cassidy, D.A.; Dates, L.R.

    1980-07-31T23:59:59.000Z

    A radioactive material storage system is claimed for use in the laboratory having a flat base plate with a groove in one surface thereof and a hollow pedestal extending perpendicularly away from the other surface thereof, a sealing gasket in the groove, a cover having a filter therein and an outwardly extending flange which fits over the plate, the groove and the gasket, and a clamp for maintaining the cover and the plate sealed together. The plate and the cover and the clamp cooperate to provide a storage area for radioactive material readily accessible for use or inventory. Wall mounts are provided to prevent accidental formation of critical masses during storage.

  16. Assigning gas balancing rights in the absence of a gas balancing agreement

    SciTech Connect (OSTI)

    Moon, M.S.

    1993-01-01T23:59:59.000Z

    When two or more working interest owners share an undivided interest in a natural gas well, it is not uncommon for production imbalances to occur. Sometimes such imbalances are remedied pursuant to a gas balancing agreement (GBA) entered into by the interest owners. However, if no GBA is entered into, the common law rules of cotenancy and any other agreement between the parties will be used to cure the production imbalance. In [open quotes]Weiser-Brown Oil Co. v. Samson Resources Co.[close quotes], the Court of Appeals for the Eighth Circuit held that, absent a GBA, a co-owner has no contractual right to recoup underproduction, only a right to an accounting as between cotenants, and that this right to an accounting does not run with the land to subsequent cotenants, but is only personal to the cotenant who has underproduced. This note analyzes the [open quotes]Weiser-Brown[close quotes] decision by first addressing the common law of cotenancy and how the common law is affected by the existence of an operating agreement. The conclusion reached is that, under an operating agreement, the right to make up an underproduction, even absent a GBA, is an assignable contract right, and that this right runs with the land to inure to subsequent grantees of the original part to the operating agreement.

  17. New Directions: A facelift for the picture of the global energy balance Earth's climate is largely regulated by the global energy balance,

    E-Print Network [OSTI]

    Fischlin, Andreas

    New Directions: A facelift for the picture of the global energy balance Earth's climate is largely regulated by the global energy balance, which considers the energy flows within the climate system a perturbation of this energy balance, through a modification of the energy flows in the polluted atmosphere

  18. DREDGED MATERIAL EVALUATION AND

    E-Print Network [OSTI]

    DREDGED MATERIAL EVALUATION AND DISPOSAL PROCEDURES (USERS' MANUAL) Dredged Material Management 2009) Prepared by: Dredged Material Management Office US Army Corps of Engineers Seattle District #12........................................................................................2-1 2.2 The Dredged Material Evaluation Process

  19. Isospin effects on the mass dependence of balance energy

    E-Print Network [OSTI]

    Sakshi Gautam; Aman D. Sood

    2010-07-09T23:59:59.000Z

    We study the effect of isospin degree of freedom on balance energy throughout the mass range between 50 and 350 for two sets of isotopic systems with N/Z = 1.16 and 1.33 as well as isobaric systems with N/Z = 1.0 and 1.4. Our findings indicate that different values of balance energy for two isobaric systems may be mainly due to the Coulomb repulsion. We also demonstrate clearly the dominance of Coulomb repulsion over symmetry energy.

  20. Isospin effects on the mass dependence of the balance energy

    SciTech Connect (OSTI)

    Gautam, Sakshi [Department of Physics, Panjab University, Chandigarh 160 014 (India); Sood, Aman D. [SUBATECH, Laboratoire de Physique Subatomique et des Technologies Associees, Universite de Nantes, IN2P3/CNRS, EMN 4 rue Alfred Kastler, F-44072 Nantes (France)

    2010-07-15T23:59:59.000Z

    We study the effect of isospin degree of freedom on balance energy throughout the mass range between 50 and 350 for two sets of isotopic systems with N/A= 0.54 and 0.57 as well as isobaric systems with N/A= 0.5 and 0.58. Our findings indicate that different values of balance energy for two isobaric systems may be mainly due to the Coulomb repulsion. We also demonstrate clearly the dominance of Coulomb repulsion over symmetry energy.

  1. area supplemental coatings: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    unknown authors 4 Continuous blade coating for multi-layer large-area organic light-emitting diode and solar cell Materials Science Websites Summary: Continuous blade coating for...

  2. area solar neutron: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hessels, Jason; 10.1038nature09466 2010-01-01 19 Evaluating Business Opportunities with Solar Energy in Un-electrified Areas' in Materials Science Websites Summary: -electrified,...

  3. Nutrient Management Examination Competency Areas Commercial and Public Specialists

    E-Print Network [OSTI]

    Guiltinan, Mark

    of the publications and reference materials are included on the Nutrient Management Resource CD distributedv.01.2014 Nutrient Management Examination Competency Areas Commercial and Public Specialists Management Specialist Certification Program. If a person understands the subject matter described

  4. What can I do with this major? AREAS EMPLOYERS

    E-Print Network [OSTI]

    Escher, Christine

    Quality assurance Materials Management: Purchasing/buying Traffic management Inventory management DevelopSTRATEGIES What can I do with this major? AREAS EMPLOYERS MANAGEMENT HUMAN RESOURCE MANAGEMENT MANAGEMENT Business and industry including: Banks and financial institutions Retail stores Restaurants Hotels

  5. 300 AREA URANIUM CONTAMINATION

    SciTech Connect (OSTI)

    BORGHESE JV

    2009-07-02T23:59:59.000Z

    {sm_bullet} Uranium fuel production {sm_bullet} Test reactor and separations experiments {sm_bullet} Animal and radiobiology experiments conducted at the. 331 Laboratory Complex {sm_bullet} .Deactivation, decontamination, decommissioning,. and demolition of 300 Area facilities

  6. Decontamination & decommissioning focus area

    SciTech Connect (OSTI)

    NONE

    1996-08-01T23:59:59.000Z

    In January 1994, the US Department of Energy Office of Environmental Management (DOE EM) formally introduced its new approach to managing DOE`s environmental research and technology development activities. The goal of the new approach is to conduct research and development in critical areas of interest to DOE, utilizing the best talent in the Department and in the national science community. To facilitate this solutions-oriented approach, the Office of Science and Technology (EM-50, formerly the Office of Technology Development) formed five Focus AReas to stimulate the required basic research, development, and demonstration efforts to seek new, innovative cleanup methods. In February 1995, EM-50 selected the DOE Morgantown Energy Technology Center (METC) to lead implementation of one of these Focus Areas: the Decontamination and Decommissioning (D & D) Focus Area.

  7. S108 august 2009| balance (annual net balance and its summer/winter

    E-Print Network [OSTI]

    Box, Jason E.

    (relative to 2000­04 climatol- ogy) on the North Ellesmere, Agassiz, and Axel Heiberg ice caps ranged from melt duration anomalies, mostly due to early freeze-up. The total ice shelf area in Arctic Canada climate affects the health of Arctic glaciers. As most 2007­08 measurements are not yet available, we

  8. Physics Thrust Areas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for RenewableSpeedingBiomassPPPOPetroleum ReservesThrust Areas Physics Thrust Areas

  9. Method for forming materials

    DOE Patents [OSTI]

    Tolle, Charles R. (Idaho Falls, ID); Clark, Denis E. (Idaho Falls, ID); Smartt, Herschel B. (Idaho Falls, ID); Miller, Karen S. (Idaho Falls, ID)

    2009-10-06T23:59:59.000Z

    A material-forming tool and a method for forming a material are described including a shank portion; a shoulder portion that releasably engages the shank portion; a pin that releasably engages the shoulder portion, wherein the pin defines a passageway; and a source of a material coupled in material flowing relation relative to the pin and wherein the material-forming tool is utilized in methodology that includes providing a first material; providing a second material, and placing the second material into contact with the first material; and locally plastically deforming the first material with the material-forming tool so as mix the first material and second material together to form a resulting material having characteristics different from the respective first and second materials.

  10. Carbon-Based Materials, High-Surface-Area Sorbents, and New Materials and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof Energy Change RequestFirst Report to the PrimePilotAwards |Concepts |

  11. Generated using version 3.2 of the official AMS LATEX template Supplementary material for: Spatial and Temporal Scales of1

    E-Print Network [OSTI]

    Stevens, David

    ) then the vorticity equation does not balance. It should be noted that wd35 is not calculated in the model codeGenerated using version 3.2 of the official AMS LATEX template Supplementary material for: Spatial and Temporal Scales of1 Sverdrup Balance2 Matthew D. Thomas School of Environmental Sciences, University

  12. Plutonium focus area. Technology summary

    SciTech Connect (OSTI)

    NONE

    1997-09-01T23:59:59.000Z

    The Assistant Secretary for the Office of Environmental Management (EM) at the U.S. Department of Energy (DOE) chartered the Plutonium Focus Area (PFA) in October 1995. The PFA {open_quotes}...provides for peer and technical reviews of research and development in plutonium stabilization activities...{close_quotes} In addition, the PFA identifies and develops relevant research and technology. The purpose of this document is to focus attention on the requirements used to develop research and technology for stabilization, storage, and preparation for disposition of nuclear materials. The PFA Technology Summary presents the approach the PFA uses to identify, recommend, and review research. It lists research requirements, research being conducted, and gaps where research is needed. It also summarizes research performed by the PFA in the traditional research summary format. This document encourages researchers and commercial enterprises to do business with PFA by submitting research proposals or {open_quotes}white papers.{close_quotes} In addition, it suggests ways to increase the likelihood that PFA will recommend proposed research to the Nuclear Materials Stabilization Task Group (NMSTG) of DOE.

  13. Activation of porous MOF materials

    DOE Patents [OSTI]

    Hupp, Joseph T; Farha, Omar K

    2014-04-01T23:59:59.000Z

    A method for the treatment of solvent-containing MOF material to increase its internal surface area involves introducing a liquid into the MOF in which liquid the solvent is miscible, subjecting the MOF to supercritical conditions for a time to form supercritical fluid, and releasing the supercritical conditions to remove the supercritcal fluid from the MOF. Prior to introducing the liquid into the MOF, occluded reaction solvent, such as DEF or DMF, in the MOF can be exchanged for the miscible solvent.

  14. Evaluating dredged material placement alternatives 

    E-Print Network [OSTI]

    Wooters, Kelly Lynne

    1989-01-01T23:59:59.000Z

    , but are required in some environmentally sensitive areas. An example of an innovative disposal alternative is the application of oil spill clean-up technology to dredging sites in the form of interim storage. 1. 3 Related Research The environmental impacts... of alternatives, sociopolitical implication, and environmental impact. Specific procedural guidelines are presented for marsh, upland, and island development. Gupta et al. (1978) establish the appropriate agricultural use for the dredged materiaL Dredged...

  15. Benchmarking Non-Hardware Balance of System (Soft) Costs for

    E-Print Network [OSTI]

    Benchmarking Non-Hardware Balance of System (Soft) Costs for U.S. Photovoltaic Systems Using a Data (Soft) Costs for U.S. Photovoltaic Systems Using a Data-Driven Analysis from PV Installer Survey Results process" or "soft" costs--for residential and commercial photovoltaic (PV) systems. Annual expenditure

  16. SINR Balancing and Beamforming for the MISO Interference Channel

    E-Print Network [OSTI]

    Gesbert, David

    SINR Balancing and Beamforming for the MISO Interference Channel Francesco Negro, Martina Cardone.negro@eurecom.fr, dirk.slock@eurecom.fr Abstract--In this paper a K user multi-input single-output (MISO) interference noise contribution (Noisy IFC). We address the MISO downlink (DL) beamformer design and power allocation

  17. PAS kinase is required for normal cellular energy balance

    E-Print Network [OSTI]

    Rutter, Jared

    PAS kinase is required for normal cellular energy balance Huai-Xiang Hao*, Caleb M. Cardon*, Wojtek, University of Utah School of Medicine, Salt Lake City, UT 84112 Edited by Steven L. McKnight, University in a cell-autonomous manner to maintain cellular energy homeostasis and is a potential therapeutic target

  18. atmospheric energy balance: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    energy balance First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Ch4. Atmosphere and Surface Energy...

  19. Stray capacitances in the watt balance operation: electrostatic forces

    E-Print Network [OSTI]

    Quagliotti, Danilo

    2014-01-01T23:59:59.000Z

    In a watt balance, stray capacitances exist between the coil and the magnet. Since the electric current flowing in the coil originates a difference between the coil and magnet electric-potentials, their electrostatic interactions must be taken into account. This paper reports the results of a finite element analysis of the forces acting on the coil.

  20. Original article Energy balance storage terms and big-leaf

    E-Print Network [OSTI]

    Boyer, Edmond

    Original article Energy balance storage terms and big-leaf evapotranspiration in a mixed deciduous radiometer, which seems to be a good method. The often neglected photosynthetic heat storage may heat storage are a re- sult of complex changes of several climatic parameters. Due to the high degree

  1. Improving the Load Balancing Performance of Reliable Server Pooling

    E-Print Network [OSTI]

    Dreibholz, Thomas

    Improving the Load Balancing Performance of Reliable Server Pooling in Heterogeneous Capacity@iem.uni-due.de Abstract. The IETF is currently standardizing a light-weight protocol frame- work for server redundancy and session failover: Reliable Server Pooling (RSer- Pool). It is the novel combination of ideas from

  2. Off-Balance Sheet Financing for Industrial Energy Efficiency Projects

    E-Print Network [OSTI]

    Williams, S. J.

    of performance contracting is the off-balance sheet nature of the financing. However, as every energy manager has experienced, selling the next shared savings deal internally can be a difficult task at best. Financial types react coolly to transactions in which...

  3. Balancing Image Quality and Energy Consumption in Visual Sensor Networks

    E-Print Network [OSTI]

    Tam, Vincent W. L.

    Balancing Image Quality and Energy Consumption in Visual Sensor Networks Kit-Yee Chow, King by hop through the sensor network. To reduce the energy used in transmission, the size of the images studies the tradeoff between image quality and energy consumption. We study the scenario that a number

  4. Energy Efficient Geographical Load Balancing via Dynamic Deferral of Workload

    E-Print Network [OSTI]

    Gupta, Rajesh

    Energy Efficient Geographical Load Balancing via Dynamic Deferral of Workload Muhammad Abdullah to enhancements of the electrical grid raise the possibility of utilizing "cloud computing" for energy efficient computing. Energy efficiency in the cloud has been explored recently in [1], [2], [3], [4], [5]. While

  5. Wavelet Transforms for Vector Fields Using Omnidirectionally Balanced Multiwavelets

    E-Print Network [OSTI]

    Fowler, James E.

    Wavelet Transforms for Vector Fields Using Omnidirectionally Balanced Multiwavelets James E. Fowler, Senior Member, IEEE, and Li Hua, Student Member, IEEE Abstract--Vector wavelet transforms for vector implementation of a vector wavelet transform, namely the application of a scalar transform to each vector

  6. Balancing Generality and Specificity in Document Management Systems

    E-Print Network [OSTI]

    Edwards, Keith

    Balancing Generality and Specificity in Document Management Systems W. Keith Edwards and Anthony La-purpose applications that operate on that document. KEYWORDS: document management, user interfaces, extensible. Our desktop tools are specialized to match our document management tasks and have increased

  7. Balancing biodiversity in a changing environment: extinction debt,

    E-Print Network [OSTI]

    Sax, Dov

    Balancing biodiversity in a changing environment: extinction debt, immigration credit and species Dynamics Species immigration and extinction are the dominant forces underlying changes in species diversity environmental change. The model incorporates lags in extinction and immigration, which lead to extinction debt

  8. Electrolysis for Energy Storage & Grid Balancing in West Denmark

    E-Print Network [OSTI]

    this capacity before 2010, to about 2,700 MW. High wind power output often occurs out of phase with demand and often unpredictably. Wind power output also ramps up and down continuously, sometimes by large amounts, there is an excellent match between wind and fast responding hydro, from an overall operating and grid balancing point

  9. The Balance of Dark and Luminous Mass in Rotating Galaxies

    E-Print Network [OSTI]

    Stacy McGaugh

    2005-09-12T23:59:59.000Z

    A fine balance between dark and baryonic mass is observed in spiral galaxies. As the contribution of the baryons to the total rotation velocity increases, the contribution of the dark matter decreases by a compensating amount. This poses a fine-tuning problem for \\LCDM galaxy formation models, and may point to new physics for dark matter particles or even a modification of gravity.

  10. Test Administration Instructions for the Fullerton Advanced Balance (FAB) Scale

    E-Print Network [OSTI]

    de Lijser, Peter

    Test Administration Instructions for the Fullerton Advanced Balance (FAB) Scale 1. Stand with feet: Stopwatch with lanyard (for placing around neck). Safety Procedures: Position person being tested n a corner at eye level so participant and time can be monitored simultaneously. Testing procedures: Demonstrate

  11. Vegetated Roof Water-Balance Model: Experimental and Model Results

    E-Print Network [OSTI]

    urbanization effects on the water cycle. Although there are many stormwater best management practices (BMPs (ET) and soil media water storage between storm events. Lazzarin et al. (2005) estimated that ET ratesVegetated Roof Water-Balance Model: Experimental and Model Results James A. Sherrard Jr.1

  12. Greening Geographical Load Balancing Zhenhua Liu, Minghong Lin,

    E-Print Network [OSTI]

    Andrew, Lachlan

    balanc- ing" has been suggested to reduce energy cost by exploiting the electricity price differences that if electricity is dynamically priced in proportion to the instantaneous fraction of the total energy, the ben- efits depend strongly on the degree to which systems accept dynamic energy pricing and the form

  13. Las personas con diabetes deben lograr un balance entre los

    E-Print Network [OSTI]

    la planeación de las comidas y la selección de los ali- mentos. El método 50/50 brinda un balance% (la mitad) de porciones de ali- mentos bajos en carbohidratos. Los grupos de alimentos que contienen en un lado del plato y los alimentos bajos en carbohidratos al otro lado. Karen Halderson, MPH, RD

  14. Process and Product Certification Arguments -Getting the Balance Right

    E-Print Network [OSTI]

    Kelly, Tim

    that should be adopted by the development and assessment lifecycle. Product-based certification reliesProcess and Product Certification Arguments - Getting the Balance Right Ibrahim Habli Tim Kelly on the generation and assurance of product-specific evidence that meets safety requirements derived from hazard

  15. Balance of Plant Needs and Integration of Stack Components for

    E-Print Network [OSTI]

    balance-of-plant components? Reliability Cost Regulatory Regulatory Efficiency Components What types of components represent the greatest challenges? #12;Reliability Backup Power The National. National Emergency Number Association. 2001. Recommended Generic Standards for E9-1-1 PSAP Equipment. NENA

  16. Original article Heat balance of a multistage spray-dryer

    E-Print Network [OSTI]

    Boyer, Edmond

    into account. From these data, the heat balance showed a dif- ference between inputs and outputs of 2.9% which may be interpreted as heat losses and probable errors. The specific heat consumption was close to 4 of the small flow rates of air used in both fluid beds. This specific heat consumption corresponds to 2.1 times

  17. Grid Load Balancing Using Intelligent Agents Junwei Cao1

    E-Print Network [OSTI]

    Jarvis, Stephen

    - 1 - Grid Load Balancing Using Intelligent Agents Junwei Cao1 , Daniel P. Spooner* , Stephen A for grid computing. The management and scheduling of dynamic grid resources in a scalable way requires new technologies to implement a next generation intelligent grid environment. This work demonstrates that AI

  18. Population balance modeling -an application in particle technology

    E-Print Network [OSTI]

    Ehrman, Sheryl H.

    in industry · Design problem, sneak peak · Particle collection using cyclones · Aerosol topics ­ size distributions ­ aggregates and fractals ­ coagulation/breakup · Population balance equations · Discrete and University of Maryland Link to Matlab: www.glue.umd.edu/~sehrman/popbal.htm #12;Outline · Aerosol reactors

  19. How to balance solar and conservation in passive homes

    SciTech Connect (OSTI)

    Balcomb, D.

    1981-09-01T23:59:59.000Z

    A method is presented, step by step, which shows, for any kind of passive solar house, how air-tight to make it and how much insulation to use. The method strikes a balance between the solar savings fraction (SSF), the building load coefficient (BLC) and load collector ratio (LCR) and cost. An example is given that illustrates the method. (LEW)

  20. h"p://pegasus.isi.edu Balanced Task Clustering in

    E-Print Network [OSTI]

    Deelman, Ewa

    h"p://pegasus.isi.edu Balanced Task Clustering in Scientific Workflows Weiwei Chen*, Rafael of Manchester, School of Computer Science, Manchester, U.K. Oct 24, 2013, CNCC, Beijing 1 h"p://pegasus.isi.edu #12;h"p://pegasus.isi.edu Outline · Introduction ­ Workflow Model ­ Execution Environment · Task

  1. Integrated Finance Organization Balancing Risk and Performance with an

    E-Print Network [OSTI]

    and Petroleum Industry CFOs IBM GLOBAL BusIness seRvICes #12;Expanding the Innovation Horizon #12; Balancing of the earth's population is now engaged." ­ Ben Bernanke, Chairman, U.S. Federal Reserve, quoted in The New York Times In the globally interdependent marketplace, Chemical and Petroleum (C&P) organizations need

  2. Balancing Privacy and Fidelity in Packet Traces for Security Evaluation

    E-Print Network [OSTI]

    Fahmy, Sonia

    for a certain network. Previous attempts at developing security benchmarks include the 1998 and 1999 evaluation1 Balancing Privacy and Fidelity in Packet Traces for Security Evaluation Sonia Fahmy and Christine.com Abstract Security mechanisms, such as firewalls and intrusion detection systems, protect networks

  3. Materials for spallation neutron sources

    SciTech Connect (OSTI)

    Sommer, W.F.; Daemen, L.L. [comps.

    1996-03-01T23:59:59.000Z

    The Workshop on Materials for Spallation Neutron Sources at the Los Alamos Neutron Science Center, February 6 to 10, 1995, gathered scientists from Department of Energy national laboratories, other federal institutions, universities, and industry to discuss areas in which work is needed, successful designs and use of materials, and opportunities for further studies. During the first day of the workshop, speakers presented overviews of current spallation neutron sources. During the next 3 days, seven panels allowed speakers to present information on a variety of topics ranging from experimental and theoretical considerations on radiation damage to materials safety issues. An attempt was made to identify specific problems that require attention within the context of spallation neutron sources. This proceedings is a collection of summaries from the overview sessions and the panel presentations.

  4. OLED area illumination source

    DOE Patents [OSTI]

    Foust, Donald Franklin (Scotia, NY); Duggal, Anil Raj (Niskayuna, NY); Shiang, Joseph John (Niskayuna, NY); Nealon, William Francis (Gloversville, NY); Bortscheller, Jacob Charles (Clifton Park, NY)

    2008-03-25T23:59:59.000Z

    The present invention relates to an area illumination light source comprising a plurality of individual OLED panels. The individual OLED panels are configured in a physically modular fashion. Each OLED panel comprising a plurality of OLED devices. Each OLED panel comprises a first electrode and a second electrode such that the power being supplied to each individual OLED panel may be varied independently. A power supply unit capable of delivering varying levels of voltage simultaneously to the first and second electrodes of each of the individual OLED panels is also provided. The area illumination light source also comprises a mount within which the OLED panels are arrayed.

  5. Inner Area Principles

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn Other News linkThermalInner Area Principles The Inner Area

  6. Stanford University Department of Environmental Health and Safety G:\\CAP\\CAP Team Forms \\StorageAreaInspFillableForm.pdf Enter Inspection Date

    E-Print Network [OSTI]

    as Hazardous Materials Storage Areas (not laboratories or work areas). 2. Evaluate the storage area during-9999 (24 hours). Building Number Building Name Room Number HAZARDOUS MATERIALS STORAGE AREA: MONTHLYStanford University Department of Environmental Health and Safety G:\\CAP\\CAP Team Forms \\StorageArea

  7. Dental analysis of Classic period population variability in the Maya area 

    E-Print Network [OSTI]

    Scherer, Andrew Kenneth

    2005-02-17T23:59:59.000Z

    In this dissertation I examine population history and structure in the Maya area during the Classic period (A.D. 250-900). Within the Maya area, archaeologists have identified regional variation in material culture between ...

  8. Transporting particulate material

    DOE Patents [OSTI]

    Aldred, Derek Leslie (North Hollywood, CA); Rader, Jeffrey A. (North Hollywood, CA); Saunders, Timothy W. (North Hollywood, CA)

    2011-08-30T23:59:59.000Z

    A material transporting system comprises a material transporting apparatus (100) including a material transporting apparatus hopper structure (200, 202), which comprises at least one rotary transporting apparatus; a stationary hub structure (900) constraining and assisting the at least one rotary transporting apparatus; an outlet duct configuration (700) configured to permit material to exit therefrom and comprising at least one diverging portion (702, 702'); an outlet abutment configuration (800) configured to direct material to the outlet duct configuration; an outlet valve assembly from the material transporting system venting the material transporting system; and a moving wall configuration in the material transporting apparatus capable of assisting the material transporting apparatus in transporting material in the material transporting system. Material can be moved from the material transporting apparatus hopper structure to the outlet duct configuration through the at least one rotary transporting apparatus, the outlet abutment configuration, and the outlet valve assembly.

  9. Materials Science & Engineering

    E-Print Network [OSTI]

    Reisslein, Martin

    Materials Science & Engineering The development of new high-performance materials for energy Research in Niskayuna, NY. He received his BS and PhD in Materials Science and Engineering at MIT. For 22 and composition of materials at higher spatial resolution, with greater efficiency, and on real materials

  10. Application issues for large-area electrochromic windows in commercial buildings

    E-Print Network [OSTI]

    Lee, Eleanor S.; DiBartolomeo, D.L.

    2000-01-01T23:59:59.000Z

    Handbook of inorganic electrochromic materials. 1995.R. Sullivan. A Review of Electrochromic Window Performancetime of large-scale electrochromic devices. In Large-Area

  11. PROTECTED AREAS AMENDMENTS AND.

    E-Print Network [OSTI]

    as critical fish and wildlife habitat. The "protected areas" amendment is a major step in the Council's efforts to rebuild fish and wildlife populations that have been damaged by hydroelectric development. Low also imposed significant costs. The Northwest's fish and wildlife have suffered extensive losses

  12. MSL ENTERANCE REFERENCE AREA

    E-Print Network [OSTI]

    Aalberts, Daniel P.

    MSL ENTERANCE LOBBY ELEV STAIRS SSL-019 REFERENCE AREA SSL-021 GROUP STUDY SSL-018 STUDY ROOM SSL-029 SSL-020 COPY ROOM SSL-022 GROUP STUDY SSL-026 STACKS SSL-023 GROUP STUDY SSL-024 GROUP STUDY SSL TBL-014 TBL-014A STAIRS SSL-007 GIS/ WORKROOM SSL-011 SSL-008 SSL-009 SSL-010 SSL-014 SSL-017 STAIRS

  13. Subsurface contaminants focus area

    SciTech Connect (OSTI)

    NONE

    1996-08-01T23:59:59.000Z

    The US Department of Enregy (DOE) Subsurface Contaminants Focus Area is developing technologies to address environmental problems associated with hazardous and radioactive contaminants in soil and groundwater that exist throughout the DOE complex, including radionuclides, heavy metals; and dense non-aqueous phase liquids (DNAPLs). More than 5,700 known DOE groundwater plumes have contaminated over 600 billion gallons of water and 200 million cubic meters of soil. Migration of these plumes threatens local and regional water sources, and in some cases has already adversely impacted off-site rsources. In addition, the Subsurface Contaminants Focus Area is responsible for supplying technologies for the remediation of numerous landfills at DOE facilities. These landfills are estimated to contain over 3 million cubic meters of radioactive and hazardous buried Technology developed within this specialty area will provide efective methods to contain contaminant plumes and new or alternative technologies for development of in situ technologies to minimize waste disposal costs and potential worker exposure by treating plumes in place. While addressing contaminant plumes emanating from DOE landfills, the Subsurface Contaminants Focus Area is also working to develop new or alternative technologies for the in situ stabilization, and nonintrusive characterization of these disposal sites.

  14. NEBRASKA CENTER FOR MATERIALS AND NANOSCIENCE SEMINAR SERIES PRESENTS

    E-Print Network [OSTI]

    Farritor, Shane

    in areas such as energy storage, photovoltaics, and catalysis. These materials are often difficult to real world systems to elucidate how the inter- play of material composition and structure alters pursued to facilitate the determination of a number of material parameters such as porosity, pore size

  15. DOE Designates Southwest Area and Mid-Atlantic Area National...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Interest Electric Transmission Corridors DOE Designates Southwest Area and Mid-Atlantic Area National Interest Electric Transmission Corridors October 2, 2007 - 11:12am Addthis...

  16. Department of Materials Science &

    E-Print Network [OSTI]

    Acton, Scott

    Developing Leaders of Innovation Department of Materials Science & Engineering #12;At the University of Virginia, students in materials science, engineering physics and engineering science choose to tackle compelling issues in materials science and engineering or engineering science

  17. Nanostructured magnetic materials

    E-Print Network [OSTI]

    Chan, Keith T.

    2011-01-01T23:59:59.000Z

    Magnetism and Magnetic Materials Conference, Atlanta, GA (Nanostructured Magnetic Materials by Keith T. Chan Doctor ofinduced by a Si-based material occurs at a Si/Ni interface

  18. Estimation of Building Parameters Using Simplified Energy Balance Model and Metered Whole Building Energy Use

    E-Print Network [OSTI]

    Masuda, H.; Claridge, D.

    2012-01-01T23:59:59.000Z

    , cooling and heating and weather data using multiple linear regression models based on the simplified steady-state energy balance for a whole building. Two approaches using different response variables: the energy balance load (EBL) and the building thermal...

  19. Development of Data Quality Control Limits for Data Screening through the "Energy Balance" Method

    E-Print Network [OSTI]

    Masuda, H.; Baltazar, J. C.; Ji, J.; Claridge, D.

    screening using “Energy Balance” methodology (Shao and Claridge, 2005). Energy Balance (EBL) parameter represents quasi-steady state thermal energy storage in a building and indicates a predominant linear behavior when it is plotted versus the outside air...

  20. The Balanced Unicast and Multicast Capacity Regions of Large Wireless Networks

    E-Print Network [OSTI]

    Niesen, Urs

    We consider the question of determining the scaling of the n[superscript n] -dimensional balanced unicast and the n 2[superscript n]-dimensional balanced multicast capacity regions of a wireless network with n nodes placed ...

  1. An institutional frame to compare alternative market designs in EU electricity balancing

    E-Print Network [OSTI]

    Glachant, Jean-Michel

    2007-01-01T23:59:59.000Z

    The so-called "electricity wholesale market" is, in fact, a sequence of several markets. The chain is closed with a provision for "balancing," in which energy from all wholesale markets is balanced under the authority of ...

  2. Estimation of Building Parameters Using Simplified Energy Balance Model and Metered Whole Building Energy Use 

    E-Print Network [OSTI]

    Masuda, H.; Claridge, D.

    2012-01-01T23:59:59.000Z

    , cooling and heating and weather data using multiple linear regression models based on the simplified steady-state energy balance for a whole building. Two approaches using different response variables: the energy balance load (EBL) and the building thermal...

  3. TITLE: HVAC TESTING & BALANCING FOR MAJOR AND MINOR PROJECTS OBJECTIVE AND

    E-Print Network [OSTI]

    Fernandez, Eduardo

    TITLE: HVAC TESTING & BALANCING FOR MAJOR AND MINOR PROJECTS OBJECTIVE AND PURPOSE: To provide an independent test & balance for the adjustment of all HVAC systems in all major projects and minor projects

  4. MATERIALS TRANSFER AGREEMENT

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MTAXX-XXX 1 MATERIAL TRANSFER AGREEMENT for Manufacturing Demonstration Facility and Carbon Fiber Technology Facility In order for the RECIPIENT to obtain materials, the RECIPIENT...

  5. Materials at the Mesoscale

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Materials at the Mesoscale 1663 Los Alamos science and technology magazine Latest Issue:January 2015 All Issues submit Materials at the Mesoscale Los Alamos's bold proposal to...

  6. UNCLASSIFIED Institute for Materials ...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Institute for Materials Science Lecture Series Dr Roger D Doherty M.A. D. Phil., Fellow TMS Emeritus Professor of Materials Science and Engineering, Drexel University,...

  7. Transporting Hazardous Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Transporting Hazardous Materials The procedures given below apply to all materials that are considered to be hazardous by the U.S. Department of Transportation (DOT). Consult your...

  8. battery materials | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    battery materials battery materials Leads No leads are available at this time. Modeling Interfacial Glass-Water Reactions: Recent Advances and Current Limitations. Abstract: The...

  9. EMSL - Energy Materials & Processes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    energy Energy Materials and Processes focuses on the dynamic transformation mechanisms and physical and chemical properties at critical interfaces in catalysts and energy materials...

  10. Propulsion Materials Research Update

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    * Materials for Electric and Hybrid Drive Systems - Address materials issues impacting power electronics, motors, and other hybrid drive system components * Combustion System...

  11. Materials Technical Team Roadmap

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of these as mixed- material systems. Additionally, materials such as titanium, polycarbonate, acrylics, and metal matrix composites, and approaches to their use must be...

  12. Water balance report for the Oak Ridge Y-12 Plant

    SciTech Connect (OSTI)

    NONE

    1994-07-01T23:59:59.000Z

    The Y-12 Plant, which occupies approximately 800 acres, was built by the Army Corps of Engineers in 1943 as part of the Manhattan Project in Oak Ridge, Tennessee. Recently, Martin Marietta Energy Systems, who manages the Y-12 Plant, has been concerned with the effects of water consumption and losses at the plant facility, and the ability of ground water beneath the site to act as a source of water seepage into East Fork Poplar Creek or as a source of water infiltration into subsurface strata. This has prompted the need to perform a water balance study on the facility. Data regarding all uses of municipal water and sources of discharge from the plant were recorded and then water balance calculations were performed using a computer model developed in a multi-dimensional electronic spreadsheet. This report describes the results of this research and includes the flow data collected during the study.

  13. Small lysimeters for documenting arid site water balance

    SciTech Connect (OSTI)

    Waugh, W.J. (Chem-Nuclear Geotech, Inc., Grand Junction, CO (USA)); Thiede, M.E.; Cadwell, L.L.; Gee, G.W.; Freeman, H.D. (Pacific Northwest Lab., Richland, WA (USA)); Sackschewsky, M.R.; Relyea, J.F. (Westinghouse Hanford Co., Richland, WA (USA))

    1991-07-01T23:59:59.000Z

    Small weighing lysimeters consisting of plastic pipes with lifting and drainage fittings were installed at the arid US DOE Hanford Site in southeastern Washington State to conduct factorial experiments comparing the influences of various waste site cover designs on soil water balance. Results of a comparison of erosion control designs indicate that gravel can be mixed into the soil surface to control soil loss without influencing the water balance. In contrast, an equivalent amount of gravel applied as a surface mulch suppressed evapotranspiration resulting in increased storage and drainage. Only slight differences were observed in a comparison of storage changes in the small-tube lysimeters and adjacent large weighing lysimeters. Soil temperature curves for small-tube lysimeters and nearby soil profiles converged after insulation collars were installed. 17 refs., 6 figs.

  14. Ocean Heat Transport, Sea Ice, and Multiple Climate States: Insights from Energy Balance Models

    E-Print Network [OSTI]

    Rose, Brian Edward James

    Several extensions of energy balance models (EBMs) are explored in which (i) sea ice acts to insulate the

  15. Torsion-balance tests of the weak equivalence principle

    E-Print Network [OSTI]

    T. A. Wagner; S. Schlamminger; J. H. Gundlach; E. G. Adelberger

    2012-07-10T23:59:59.000Z

    We briefly summarize motivations for testing the weak equivalence principle and then review recent torsion-balance results that compare the differential accelerations of beryllium-aluminum and beryllium-titanium test body pairs with precisions at the part in $10^{13}$ level. We discuss some implications of these results for the gravitational properties of antimatter and dark matter, and speculate about the prospects for further improvements in experimental sensitivity.

  16. Reactor Decommissioning - Balancing Remote and Manual Activities - 12159

    SciTech Connect (OSTI)

    Cole, Matt [S.A. Technology (United States)

    2012-07-01T23:59:59.000Z

    Nuclear reactors come in a wide variety of styles, size, and ages. However, during decommissioned one issue they all share is the balancing of remotely and manually activities. For the majority of tasks there is a desire to use manual methods because remote working can be slower, more expensive, and less reliable. However, because of the unique hazards of nuclear reactors some level of remote activity will be necessary to provide adequate safety to workers and properly managed and designed it does not need to be difficult nor expensive. The balance of remote versus manual work can also affect the amount and types of waste that is generated. S.A.Technology (SAT) has worked on a number of reactor decommissioning projects over the last two decades and has a range of experience with projects using remote methods to those relying primarily on manual activities. This has created a set of lessons learned and best practices on how to balance the need for remote handling and manual operations. Finding a balance between remote and manual operations on reactor decommissioning can be difficult but by following certain broad guidelines it is possible to have a very successfully decommissioning. It is important to have an integrated team that includes remote handling experts and that this team plans the work using characterization efforts that are efficient and realistic. The equipment need to be simple, robust and flexible and supported by an on-site team committed to adapting to day-to-day challenges. Also, the waste strategy needs to incorporate the challenges of remote activities in its planning. (authors)

  17. Isospin dependence of balance energy in heavy-ion collisions

    E-Print Network [OSTI]

    Varinderjit Kaur; Dolly Sood; Suneel Kumar

    2011-09-30T23:59:59.000Z

    Based on the isospin-dependent quantum molecular dynamics (IQMD) picture, we attempt to understand the nature of transverse flow in $_{28}Ni^{58}+_{28}Ni^{58}$ and $_{26}Fe^{58}+_{26}Fe^{58}$ systems at wide range of energies and impact parameters. The isospin dependence of balance energy in transverse flow is clearly visible. The results are compared with the experimental data available.

  18. Balancing of high speed, flexible rotating shafts across critical speeds

    E-Print Network [OSTI]

    White, Gary Paul

    1977-01-01T23:59:59.000Z

    this is equivalent to eliminating certain sen- sors. Once the influence coefficient matrix is square, the solution procedure is exactly that of the single speed case. The computed balance weights should now null the rotor vibration at the sensor ports which were... critical speed, The Sin- gle Speed and the Exact Point-Speed techniques were determined to be relatively ineffective over this speed range; however, the Least Squares procedure yields a dramatic decrease in rotor vibration over the entire speed range...

  19. Net-charge fluctuations and balance functions at the LHC

    E-Print Network [OSTI]

    Michael Weber; for the ALICE collaboration

    2012-11-24T23:59:59.000Z

    The measurement of event-by-event fluctuations and charge-dependent particle correlations are used to study properties of nuclear matter at high temperatures as produced in ultrarelativistic heavy-ion collisions. We present results for event-by-event net-charge fluctuations and charge balance functions in \\Delta\\eta\\ and \\Delta\\phi\\ in Pb-Pb collisions at sqrt(s_NN)= 2.76 TeV.

  20. First law energy balance as a data screening tool

    E-Print Network [OSTI]

    Shao, Xiaojie

    2006-08-16T23:59:59.000Z

    .............................................................................................135 7.1 Introduction....................................................................................135 7.2 Pre-Screening Case 1: Harrington Tower ......................................136 7.3 Pre-Screening Case 2: The Eller O&M Building.... outside air temperature.......................68 Figure 4.18 Key characteristics of simulated results of Energy Balance Load............. 69 Figure 5.1 Main Effect plot for the Eller Oceanography & Meteorology Building....85 Figure 5...

  1. Steam Balancing and Tuning for Multifamily Residential Buildings in Chicagoland

    SciTech Connect (OSTI)

    Choi, J.; Ludwig, P.; Brand, L.

    2012-08-01T23:59:59.000Z

    Older heating systems often suffer from mis-investment--multiple contractors upgrading parts of systems in inadequate or inappropriate ways that reduce system functionality and efficiency--or from a lack of proper maintenance. This technical report addresses these barriers to information, contractor resources, and cost-savings. Building off of previous research, CNT Energy conducted a study to identify best practices for the methodology, typical costs, and energy savings associated with steam; system balancing.

  2. Scientific and Natural Areas (Minnesota)

    Broader source: Energy.gov [DOE]

    Certain scientific and natural areas are established throughout the state for the purpose of preservation and protection. Construction and new development is prohibited in these areas.

  3. Projection-free approximate balanced truncation of large unstable systems

    E-Print Network [OSTI]

    Flinois, Thibault L B; Schmid, Peter J

    2015-01-01T23:59:59.000Z

    In this article, we show that the projection-free, snapshot-based, balanced truncation method can be applied directly to unstable systems. We prove that even for unstable systems, the unmodified balanced proper orthogonal decomposition algorithm theoretically yields a converged transformation that balances the Gramians (including the unstable subspace). We then apply the method to a spatially developing unstable system and show that it results in reduced-order models of similar quality to the ones obtained with existing methods. Due to the unbounded growth of unstable modes, a practical restriction on the final impulse response simulation time appears, which can be adjusted depending on the desired order of the reduced-order model. Recommendations are given to further reduce the cost of the method if the system is large and to improve the performance of the method if it does not yield acceptable results in its unmodified form. Finally, the method is applied to the linearized flow around a cylinder at Re = 100...

  4. Energy-momentum balance in particle - domain wall perforating collision

    E-Print Network [OSTI]

    D. V. Gal'tsov; E. Yu. Melkumova; P. A. Spirin

    2015-02-10T23:59:59.000Z

    We investigate the energy-momentum balance in the perforating collision of a point particle with an infinitely thin planar domain wall within the linearized gravity in arbitrary dimensions. Since the metric of the wall increases with distance, the wall and the particle are never free, and their energy-momentum balance involves not only the instantaneous kinetic momenta, but also the non-local contribution of gravitational stresses. However, careful analysis shows that the stresses can be unambiguously divided between the colliding objects leading to definition of the gravitationally dressed momenta. These take into account for gravity in the same way as the potential energy does in the non-relativistic theory, but our treatment is fully relativistic. Another unusual feature of our problem is the non-vanishing flux of the total energy-momentum tensor through the lateral surface of the world tube. In this case the zero divergence of the energy-momentum tensor does not imply conservation of the total momentum defined as the integral over the space-like section of the tube. But one can still define the conservation low infinitesimally, passing to time derivatives of the momenta. Using this definition we establish the momentum balance in terms of the dressed particle and wall momenta.

  5. Stochastic solution of population balance equations for reactor networks

    SciTech Connect (OSTI)

    Menz, William J.; Akroyd, Jethro; Kraft, Markus

    2014-01-01T23:59:59.000Z

    This work presents a sequential modular approach to solve a generic network of reactors with a population balance model using a stochastic numerical method. Full-coupling to the gas-phase is achieved through operator-splitting. The convergence of the stochastic particle algorithm in test networks is evaluated as a function of network size, recycle fraction and numerical parameters. These test cases are used to identify methods through which systematic and statistical error may be reduced, including by use of stochastic weighted algorithms. The optimal algorithm was subsequently used to solve a one-dimensional example of silicon nanoparticle synthesis using a multivariate particle model. This example demonstrated the power of stochastic methods in resolving particle structure by investigating the transient and spatial evolution of primary polydispersity, degree of sintering and TEM-style images. Highlights: •An algorithm is presented to solve reactor networks with a population balance model. •A stochastic method is used to solve the population balance equations. •The convergence and efficiency of the reported algorithms are evaluated. •The algorithm is applied to simulate silicon nanoparticle synthesis in a 1D reactor. •Particle structure is reported as a function of reactor length and time.

  6. Energy-Aware Load Balancing in Content Delivery Networks

    E-Print Network [OSTI]

    Mathew, Vimal; Shenoy, Prashant

    2011-01-01T23:59:59.000Z

    Internet-scale distributed systems such as content delivery networks (CDNs) operate hundreds of thousands of servers deployed in thousands of data center locations around the globe. Since the energy costs of operating such a large IT infrastructure are a significant fraction of the total operating costs, we argue for redesigning CDNs to incorporate energy optimizations as a first-order principle. We propose techniques to turn off CDN servers during periods of low load while seeking to balance three key design goals: maximize energy reduction, minimize the impact on client-perceived service availability (SLAs), and limit the frequency of on-off server transitions to reduce wear-and-tear and its impact on hardware reliability. We propose an optimal offline algorithm and an online algorithm to extract energy savings both at the level of local load balancing within a data center and global load balancing across data centers. We evaluate our algorithms using real production workload traces from a large commercial ...

  7. Dynamic Load Balancing for I/O-and Memory-Intensive Workload in Clusters Using a

    E-Print Network [OSTI]

    Zhu, Yifeng

    Load-Balancing Scheme We consider the issue of a feedback control method in a cluster, M = {M1, ..., Mn/O, respectively, without any resource sharing. For a newly arrived job j at a node i, load balancing schemesDynamic Load Balancing for I/O- and Memory-Intensive Workload in Clusters Using a Feedback Control

  8. Inspector-Executor Load Balancing Algorithms for Block-Sparse Tensor Contractions

    E-Print Network [OSTI]

    Balaji, Pavan

    --Developing effective yet scalable load-balancing methods for irregular computations is critical to the successful, any form of centralized dynamic load balancing, such as master-worker or a shared counter (eInspector-Executor Load Balancing Algorithms for Block-Sparse Tensor Contractions David Ozog, Jeff

  9. Framework for Coupling Room Air Models to Heat Balance Model Load and Energy Calculations (RP-1222)

    E-Print Network [OSTI]

    Chen, Qingyan "Yan"

    1 Framework for Coupling Room Air Models to Heat Balance Model Load and Energy Calculations (RP in a program for hourly load calculations of a single thermal zone. The heat balance model for load and energy to heat balance model load and energy calculations," HVAC&R Research, 10(2), 91-111. #12;2 · Mixed

  10. A Finite Element Algorithm of a Nonlinear Diffusive Climate Energy Balance Model

    E-Print Network [OSTI]

    Díaz, Jesús Ildefonso

    A Finite Element Algorithm of a Nonlinear Diffusive Climate Energy Balance Model R. BERMEJO,1 J. This model belongs to the category of energy balance models introduced independently by the climatologists M climate. The energy balance model we are dealing with consists of a two-dimensional nonlinear parabolic

  11. Sub-grid parameterization of snow distribution for an energy and mass balance snow cover model

    E-Print Network [OSTI]

    Sub-grid parameterization of snow distribution for an energy and mass balance snow cover model model of the lumped snowpack mass and energy balance applied to a 26-ha rangeland catchment with high (Af). The energy state variable is evolved through an energy balance. The snow water equivalence state

  12. Non-Blocking, Localized Routing Algorithm for Balanced Energy Consumption in Mobile Ad Hoc Networks

    E-Print Network [OSTI]

    Lee, Ben

    1 Non-Blocking, Localized Routing Algorithm for Balanced Energy Consumption in Mobile Ad Hoc relevant nodes but also to balance individual battery levels. Unbalanced energy usage will result achieves a trade-off between balanced energy consumption and shortest routing delay, and at the same time

  13. N/Z dependence of balance energy throughout the colliding geometries

    E-Print Network [OSTI]

    Sakshi Gautam; Rajeev K. Puri

    2011-07-28T23:59:59.000Z

    We study the N/Z dependence of balance energy throughout the mass range for colliding geometry varying from central to peripheral ones. Our results indicate that balance energy decreases linearly with increase in N/Z ratio for all the masses throughout the colliding geometry range. Also, the N/Z dependence of balance energy is sensitive to symmetry energy.

  14. Load-Balanced Routing Scheme for Energy-Efficient Wireless Sensor Networks

    E-Print Network [OSTI]

    Boutaba, Raouf

    Load-Balanced Routing Scheme for Energy-Efficient Wireless Sensor Networks Fatma Bouabdallah, Nizar. In this paper, we investigate the potential energy conservation achieved by balancing the traffic throughout, load balancing, performance analysis. I. INTRODUCTION In order to minimize the energy consumption

  15. Harmonic propagation of variability in surface energy balance within a coupled soilvegetationatmosphere system

    E-Print Network [OSTI]

    Gentine, Pierre

    Harmonic propagation of variability in surface energy balance within a coupled energy balance. The amplitude of the noise is maximum at midday when the incoming radiative forcing results in changes in the surface energy balance through the modification of outgoing radiative, turbulent

  16. SUBGRID PARAMETERIZATION OF SNOW DISTRIBUTION FOR AN ENERGY AND MASS BALANCE SNOW COVER MODEL

    E-Print Network [OSTI]

    Tarboton, David

    SUBGRID PARAMETERIZATION OF SNOW DISTRIBUTION FOR AN ENERGY AND MASS BALANCE SNOW COVER MODEL & Sons, Ltd. #12;1 SUBGRID PARAMETERIZATION OF SNOW DISTRIBUTION FOR AN ENERGY AND MASS BALANCE SNOW of the lumped snowpack mass and energy balance applied to a 26-ha rangeland catchment with high spatial

  17. A Scalable Model for Energy Load Balancing in Large-scale Sensor Networks

    E-Print Network [OSTI]

    de Veciana, Gustavo

    A Scalable Model for Energy Load Balancing in Large-scale Sensor Networks Seung Jun Baek we consider how one might achieve more balanced energy burdens across the network by spreading sinks change their locations to balance the energy burdens incurred accross the network nodes [1

  18. Improving the Energy Balance of Field-based Routing in Wireless Sensor Networks

    E-Print Network [OSTI]

    Bustamante, Fabián E.

    Improving the Energy Balance of Field-based Routing in Wireless Sensor Networks Goce Trajcevski of the network merge into a single path. These path merging effects decrease significantly the energy balance deployments. When multiple sources transmit infor- mation simultaneously, together with energy balancing

  19. The global energy balance from a surface perspective Martin Wild Doris Folini Christoph Schar

    E-Print Network [OSTI]

    Fischlin, Andreas

    The global energy balance from a surface perspective Martin Wild · Doris Folini · Christoph Scha of the global energy balance, the radiative energy exchanges between Sun, Earth and space are now accurately to constrain the global energy balance not only from space, but also from the surface. We combine

  20. Energy-Balanced Cooperative Routing in Multihop Wireless Ad Hoc Networks

    E-Print Network [OSTI]

    Wang, Yu

    Energy-Balanced Cooperative Routing in Multihop Wireless Ad Hoc Networks Siyuan Chen Minsu Huang. In this paper, we aim to study the impact of cooperative routing on balancing the energy distribution among their transmission power, our cooperative routing method can balance the energy among neighboring nodes and maximize