Sample records for manzanita prius lead

  1. AVTA: 2012 Toyota Prius PHEV Downloadable Dynamometer Database...

    Energy Savers [EERE]

    Toyota Prius PHEV Downloadable Dynamometer Database Reports AVTA: 2012 Toyota Prius PHEV Downloadable Dynamometer Database Reports The Vehicle Technologies Office's Advanced...

  2. Toyota Gen III Prius Hybrid Electric Vehicle Accelerated Testing...

    Broader source: Energy.gov (indexed) [DOE]

    HEV Accelerated Testing - September 2011 Two model year 2010 Toyota Generation III Prius hybrid electric vehicles (HEVs) entered Accelerated testing during July 2009 in a fleet in...

  3. AVTA: Toyota Prius PHEV 2013 Testing Results

    Broader source: Energy.gov [DOE]

    The Vehicle Technologies Office's Advanced Vehicle Testing Activity carries out testing on a wide range of advanced vehicles and technologies on dynamometers, closed test tracks, and on-the-road. These results provide benchmark data that researchers can use to develop technology models and guide future research and development. The following reports describe results of testing done on a Toyota Prius PHEV 2013. Baseline and battery testing data collected at Argonne National Laboratory is available in summary and CSV form on the Argonne Downloadable Dynometer Database site (http://www.transportation.anl.gov/D3/2013_toyota_prius_phev.html). The reports for download here are based on research done at Idaho National Laboratory. Taken together, these reports give an overall view of how this vehicle functions under extensive testing.

  4. HEV Fleet Testing - Summary Fact Sheet 2010 Toyota Prius

    Broader source: Energy.gov (indexed) [DOE]

    Toyota Prius VIN JTDKN3DU2A5010462 Vehicle Specifications Engine: 1.8 L 4-cylinder Electric Motor: 60 kW Battery: NiMH Seatbelt Positions: Five Payload: 885 lbs Features:...

  5. 2010 Toyota Prius VIN 0462 Hybrid Electric Vehicle Battery Test...

    Broader source: Energy.gov (indexed) [DOE]

    5 2010 Toyota Prius VIN 0462 Hybrid Electric Vehicle Battery Test Results Tyler Gray Matthew Shirk January 2013 The Idaho National Laboratory is a U.S. Department of Energy...

  6. 2010 Toyota Prius VIN 6063 Hybrid Electric Vehicle Battery Test...

    Broader source: Energy.gov (indexed) [DOE]

    6 2010 Toyota Prius VIN 6063 Hybrid Electric Vehicle Battery Test Results Tyler Gray Matthew Shirk January 2013 The Idaho National Laboratory is a U.S. Department of Energy...

  7. Evaluation of 2004 Toyota Prius Hybrid Electric Drive System

    SciTech Connect (OSTI)

    Staunton, Robert H [ORNL; Ayers, Curtis William [ORNL; Chiasson, J. N. [University of Tennessee, Knoxville (UTK); Burress, Timothy A [ORNL; Marlino, Laura D [ORNL

    2006-05-01T23:59:59.000Z

    The 2004 Toyota Prius is a hybrid automobile equipped with a gasoline engine and a battery- and generator-powered electric motor. Both of these motive-power sources are capable of providing mechanical-drive power for the vehicle. The engine can deliver a peak-power output of 57 kilowatts (kW) at 5000 revolutions per minute (rpm) while the motor can deliver a peak-power output of 50 kW over the speed range of 1200-1540 rpm. Together, this engine-motor combination has a specified peak-power output of 82 kW at a vehicle speed of 85 kilometers per hour (km/h). In operation, the 2004 Prius exhibits superior fuel economy compared to conventionally powered automobiles. To acquire knowledge and thereby improve understanding of the propulsion technology used in the 2004 Prius, a full range of design characterization studies were conducted to evaluate the electrical and mechanical characteristics of the 2004 Prius and its hybrid electric drive system. These characterization studies included (1) a design review, (2) a packaging and fabrication assessment, (3) bench-top electrical tests, (4) back-electromotive force (emf) and locked rotor tests, (5) loss tests, (6) thermal tests at elevated temperatures, and most recently (7) full-design-range performance testing in a controlled laboratory environment. This final test effectively mapped the electrical and thermal results for motor/inverter operation over the full range of speeds and shaft loads that these assemblies are designed for in the Prius vehicle operations. This testing was undertaken by the Oak Ridge National Laboratory (ORNL) as part of the U.S. Department of Energy (DOE) - Energy Efficiency and Renewable Energy (EERE) FreedomCAR and Vehicle Technologies (FCVT) program through its vehicle systems technologies subprogram. The thermal tests at elevated temperatures were conducted late in 2004, and this report does not discuss this testing in detail. The thermal tests explored the derating of the Prius motor design if operated at temperatures as high as is normally encountered in a vehicle engine. The continuous ratings at base speed (1200 rpm) with different coolant temperatures are projected from test data at 900 rpm. A separate, comprehensive report on this thermal control study is available [1].

  8. Evaluation of 2004 Toyota Prius Hybrid Electric Drive System

    SciTech Connect (OSTI)

    Staunton, R.H.; Ayers, C.W.; Chiasson, J.N. (U Tennessee-Knoxville); Burress, B.A. (ORISE); Marlino, L.D.

    2006-05-01T23:59:59.000Z

    The 2004 Toyota Prius is a hybrid automobile equipped with a gasoline engine and a battery- and generator-powered electric motor. Both of these motive-power sources are capable of providing mechanical-drive power for the vehicle. The engine can deliver a peak-power output of 57 kilowatts (kW) at 5000 revolutions per minute (rpm) while the motor can deliver a peak-power output of 50 kW over the speed range of 1200-1540 rpm. Together, this engine-motor combination has a specified peak-power output of 82 kW at a vehicle speed of 85 kilometers per hour (km/h). In operation, the 2004 Prius exhibits superior fuel economy compared to conventionally powered automobiles. To acquire knowledge and thereby improve understanding of the propulsion technology used in the 2004 Prius, a full range of design characterization studies were conducted to evaluate the electrical and mechanical characteristics of the 2004 Prius and its hybrid electric drive system. These characterization studies included (1) a design review, (2) a packaging and fabrication assessment, (3) bench-top electrical tests, (4) back-electromotive force (emf) and locked rotor tests, (5) loss tests, (6) thermal tests at elevated temperatures, and most recently (7) full-design-range performance testing in a controlled laboratory environment. This final test effectively mapped the electrical and thermal results for motor/inverter operation over the full range of speeds and shaft loads that these assemblies are designed for in the Prius vehicle operations. This testing was undertaken by the Oak Ridge National Laboratory (ORNL) as part of the U.S. Department of Energy (DOE)-Energy Efficiency and Renewable Energy (EERE) FreedomCAR and Vehicle Technologies (FCVT) program through its vehicle systems technologies subprogram. The thermal tests at elevated temperatures were conducted late in 2004, and this report does not discuss this testing in detail. The thermal tests explored the derating of the Prius motor design if operated at temperatures as high as is normally encountered in a vehicle engine. The continuous ratings at base speed (1200 rpm) with different coolant temperatures are projected from test data at 900 rpm. A separate, comprehensive report on this thermal control study is available [1].

  9. Microsoft Word - TM-2010-253 - 2010 Prius Report - 26 - Tim ...

    Office of Scientific and Technical Information (OSTI)

    11 EVALUATION OF THE 2010 TOYOTA PRIUS HYBRID SYNERGY DRIVE SYSTEM Prepared by: Oak Ridge National Laboratory Mitch Olszewski, Program Manager Submitted to: Energy Efficiency and...

  10. AVTA: Toyota Prius Gen III HEV 2010 Testing Results

    Broader source: Energy.gov [DOE]

    The Vehicle Technologies Office's Advanced Vehicle Testing Activity carries out testing on a wide range of advanced vehicles and technologies on dynamometers, closed test tracks, and on-the-road. These results provide benchmark data that researchers can use to develop technology models and guide future research and development. The following reports describe results of testing done on a 2010 Toyota Prius III hybrid-electric vehicle. Baseline data, which provides a point of comparison for the other test results, was collected at two different research laboratories. Baseline and other data collected at Idaho National Laboratory is in the attached documents. Baseline and battery testing data collected at Argonne National Laboratory is available in summary and CSV form on the Argonne Downloadable Dynometer Database site (http://www.transportation.anl.gov/D3/2010_toyota_prius.html). Taken together, these reports give an overall view of how this vehicle functions under extensive testing.

  11. AVTA: 2012 Toyota Prius PHEV Downloadable Dynamometer Database Reports |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up fromDepartment of Energy 601Department of Energy Toyota Prius PHEV

  12. Report on Toyota/Prius Motor Torque-Capability, Torque-Property, No-Load Back EMF, and Mechanical Losses

    SciTech Connect (OSTI)

    Hsu, J.S.

    2004-09-30T23:59:59.000Z

    In today's hybrid vehicle market, the Toyota Prius drive system is currently considered the leader in electrical, mechanical, and manufacturing innovations. It is significant that in today's marketplace, Toyota is able to manufacture and sell the vehicle for a profit. This project's objective is to test the torque capability of the 2004 Prius motor and to analyze the torque properties relating to the rotor structure. The tested values of no-load back electromotive force (emf) and mechanical losses are also presented.

  13. Field Operations Program, Toyota PRIUS Hybrid Electric Vehicle Performance Characterization Report

    SciTech Connect (OSTI)

    Francfort, James Edward; Nguyen, N.; Phung, J.; Smith, J.; Wehrey, M.

    2001-12-01T23:59:59.000Z

    The U.S. Department of Energy’s Field Operations Program evaluates advanced technology vehicles in real-world applications and environments. Advanced technology vehicles include pure electric, hybrid electric, hydrogen, and other vehicles that use emerging technologies such as fuel cells. Information generated by the Program is targeted to fleet managers and others considering the deployment of advanced technology vehicles. As part of the above activities, the Field Operations Program has initiated the testing of the Toyota Prius hybrid electric vehicle (HEV), a technology increasingly being considered for use in fleet applications. This report describes the Pomona Loop testing of the Prius, providing not only initial operational and performance information, but also a better understanding of HEV testing issues. The Pomona Loop testing includes both Urban and Freeway drive cycles, each conducted at four operating scenarios that mix minimum and maximum payloads with different auxiliary (e.g., lights, air conditioning) load levels.

  14. Evaluation of 2004 Toyota Prius Hybrid Electric Drive System Interim Report

    SciTech Connect (OSTI)

    Ayers, C.W.

    2004-11-23T23:59:59.000Z

    Laboratory tests were conducted to evaluate the electrical and mechanical performance of the 2004 Toyota Prius and its hybrid electric drive system. As a hybrid vehicle, the 2004 Prius uses both a gasoline-powered internal combustion engine and a battery-powered electric motor as motive power sources. Innovative algorithms for combining these two power sources results in improved fuel efficiency and reduced emissions compared to traditional automobiles. Initial objectives of the laboratory tests were to measure motor and generator back-electromotive force (emf) voltages and determine gearbox-related power losses over a specified range of shaft speeds and lubricating oil temperatures. Follow-on work will involve additional performance testing of the motor, generator, and inverter. Information contained in this interim report summarizes the test results obtained to date, describes preliminary conclusions and findings, and identifies additional areas for further study.

  15. Model year 2010 (Gen 3) Toyota Prius level 1 testing report.

    SciTech Connect (OSTI)

    Rask, E.; Duoba, M.; Lohse-Busch, H.; Bocci, D.; Energy Systems

    2010-06-24T23:59:59.000Z

    As a part of the US Department of Energy's Advanced Vehicle Testing Activity (AVTA), a model year 2010 Toyota Prius (Generation 3) was procured by eTec (Phoenix, AZ) and sent to ANL's Advanced Powertrain Research Facility for the purposes of 'Level 1' testing in support of the Advanced Vehicle Testing Activity (AVTA). Data was acquired during testing using non-intrusive sensors, vehicle network connection, and facilities equipment (emissions and dynamometer data). Standard drive cycles, performance cycles, steady-state cycles and A/C usage cycles were conducted. Much of this data is openly available for download in ANL's Downloadable Dynamometer Database (D{sup 3}). The major results are shown here in this report. Given the preliminary nature of this assessment, the majority of the testing was done over standard regulatory cycles and seeks to obtain a general overview of how the vehicle performs. These cycles include the US FTP cycle (Urban) and Highway Fuel Economy Test cycle as well as the US06, a more aggressive supplemental regulatory cycle. Data collection for this testing was kept at a fairly high level and includes emissions and fuel measurements from the exhaust emissions bench, high-voltage and accessory current and voltage from a DC power analyzer, and minimal CAN bus data such as engine speed and pedal position. The following sections will seek to explain some of the basic operating characteristics of the MY2010 Prius over standard regulatory cycles.

  16. 2010 Toyota Prius VIN 6063 Hybrid Electric Vehicle Battery Test Results

    SciTech Connect (OSTI)

    Tyler Gray; Matthew Shirk

    2013-01-01T23:59:59.000Z

    The U.S. Department of Energy Advanced Vehicle Testing Activity Program consists of vehicle, battery, and infrastructure testing on advanced technology related to transportation. The activity includes tests on hybrid electric vehicles (HEVs), including testing the HEV batteries when both the vehicles and batteries are new and at the conclusion of 160,000 miles of on road fleet testing. This report documents battery testing performed for the 2010 Toyota Prius HEV (VIN JTDKN3DU5A0006063). Battery testing was performed by the Electric Transportation Engineering Corporation dba ECOtality North America. The Idaho National Laboratory and ECOtality North America collaborate on the Advanced Vehicle Testing Activity for the Vehicle Technologies Program of the U.S. Department of Energy.

  17. 2010 Toyota Prius VIN 0462 Hybrid Electric Vehicle Battery Test Results

    SciTech Connect (OSTI)

    Tyler Gray; Matthew Shirk

    2013-01-01T23:59:59.000Z

    The U.S. Department of Energy Advanced Vehicle Testing Activity Program consists of vehicle, battery, and infrastructure testing on advanced technology related to transportation. The activity includes tests on hybrid electric vehicles (HEVs), including testing the HEV batteries when both the vehicles and batteries are new and at the conclusion of 160,000 miles of on road fleet testing. This report documents battery testing performed for the 2010 Toyota Prius HEV (VIN: JTDKN3DU2A5010462). Battery testing was performed by the Electric Transportation Engineering Corporation dba ECOtality North America. The Idaho National Laboratory and ECOtality North America collaborate on the Advanced Vehicle Testing Activity for the Vehicle Technologies Program of the U.S. Department of Energy.

  18. Lead

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector General Office0-72.pdfGeorgeDoesn't Happen to HighJosephNOx Traps forLM2LarryLaws andtopic Lead

  19. Hybrid Electric Vehicle End-Of-Life Testing On Honda Insights, Gen I Civics And Toyota Gen I Priuses

    SciTech Connect (OSTI)

    James Francfort; Donald Karner; Ryan Harkins; Joseph Tardiolo

    2006-02-01T23:59:59.000Z

    This technical report details the end-of-life fuel efficiency and battery testing on two model year 2001 Honda Insight hybrid electric vehicles (HEVs), two model year 2003 Honda Civic HEVs, and two model year 2002 Toyota Prius HEVs. The end-of-life testing was conducted after each vehicle has been operated for approximately 160,000 miles. This testing was conducted by the U.S. Department of Energy’s (DOE) Advanced Vehicle Testing Activity (AVTA). The AVTA is part of DOE’s FreedomCAR and Vehicle Technologies Program. SAE J1634 fuel efficiency testing was performed on the six HEVs with the air conditioning (AC) on and off. The AC on and off test results are compared to new vehicle AC on and off fuel efficiencies for each HEV model. The six HEVs were all end-of-life tested using new-vehicle coast down coefficients. In addition, one of each HEV model was also subjected to fuel efficiency testing using coast down coefficients obtained when the vehicles completed 160,000 miles of fleet testing. Traction battery pack capacity and power tests were also performed on all six HEVs during the end-of-life testing in accordance with the FreedomCAR Battery Test Manual For Power-Assist Hybrid Electric Vehicles procedures. When using the new-vehicle coast down coefficients (Phase I testing), 11 of 12 HEV tests (each HEV was tested once with the AC on and once with the AC off) had increases in fuel efficiencies compared to the new vehicle test results. The end-of-life fuel efficiency tests using the end-of-life coast down coefficients (Phase II testing) show decreases in fuel economies in five of six tests (three with the AC on and three with it off). All six HEVs experienced decreases in battery capacities, with the two Insights having the highest remaining capacities and the two Priuses having the lowest remaining capacities. The AVTA’s end-of-life testing activities discussed in this report were conducted by the Idaho National Laboratory; the AVTA testing partner Electric Transportation Applications, and by Exponent Failure Analysis Associates.

  20. Toyota Prius Plug-In HEV: A Plug-In Hybrid Electric Car in NREL's Advanced Technology Vehicle Fleet (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-10-01T23:59:59.000Z

    This fact sheet highlights the Toyota Prius plug-in HEV, a plug-in hybrid electric car in the advanced technology vehicle fleet at the National Renewable Energy Laboratory (NREL). In partnership with the University of Colorado, NREL uses the vehicle for grid-integration studies and for testing new hardware and charge-management algorithms. NREL's advanced technology vehicle fleet features promising technologies to increase efficiency and reduce emissions without sacrificing safety or comfort. The fleet serves as a technology showcase, helping visitors learn about innovative vehicles that are available today or are in development. Vehicles in the fleet are representative of current, advanced, prototype, and emerging technologies.

  1. MANZANITA Fall 2009 Getting the Dirt on Roots

    E-Print Network [OSTI]

    Bruns, Tom

    ;2 nitrogen and phosphorous, and water from the soil to support their photosynthetic activities. Fungi lack

  2. Manzanita Estates District Heating Low Temperature Geothermal Facility |

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429Lacey,(MonasterLowellis a town in CarrollManteca,Change | OpenMany

  3. Drinking Water Problems: Lead

    E-Print Network [OSTI]

    Dozier, Monty; McFarland, Mark L.

    2004-02-20T23:59:59.000Z

    Lead in drinking water can damage the brain, kidneys, nervous system and red blood cells. This publication explains how lead can enter drinking water, how to have your water tested, and how to eliminate lead from drinking water....

  4. Lead carbonate scintillator materials

    DOE Patents [OSTI]

    Derenzo, S.E.; Moses, W.W.

    1991-05-14T23:59:59.000Z

    Improved radiation detectors containing lead carbonate or basic lead carbonate as the scintillator element are disclosed. Both of these scintillators have been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to other known scintillator materials. The radiation detectors disclosed are favorably suited for use in general purpose detection and in medical uses. 3 figures.

  5. HEV Fleet Testing - Summary Fact Sheet for 2010 Toyota Prius

    Broader source: Energy.gov (indexed) [DOE]

    courts, law offices, and medical facilities on city streets and urban freeways. Vehicle Specifications Engine: 1.8 L 4-cylinder Electric Motor: 60 kW Battery: NiMH Seatbelt...

  6. Maintenance Records for 2010 Toyota Prius vin#0462

    Broader source: Energy.gov (indexed) [DOE]

    DU2A5010462 Date Mileage Description Cost 11232009 5,935 Changed oil and filter, rotated tires, and inspected brakes 31.75 12182009 13,330 Changed oil and filter and inspected...

  7. Honey, Did You Plug in the Prius? | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGYWomentheATLANTA,Fermi National AcceleratorMemoranda and Action

  8. AVTA: 2013 Toyota Prius PHEV Testing Results | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up fromDepartment of Energy 601Department of Energy Toyota

  9. Breakthrough: Lead-free Solder

    ScienceCinema (OSTI)

    Anderson, Iver

    2013-03-01T23:59:59.000Z

    Ames Laboratory senior metallurgist Iver Anderson explains the importance of lead-free solder in taking hazardous lead out of the environment by eliminating it from discarded computers and electronics that wind up in landfills. Anderson led a team that developed a tin-silver-copper replacement for traditional lead-tin solder that has been adopted by more than 50 companies worldwide.

  10. Breakthrough: Lead-free Solder

    SciTech Connect (OSTI)

    Anderson, Iver

    2012-01-01T23:59:59.000Z

    Ames Laboratory senior metallurgist Iver Anderson explains the importance of lead-free solder in taking hazardous lead out of the environment by eliminating it from discarded computers and electronics that wind up in landfills. Anderson led a team that developed a tin-silver-copper replacement for traditional lead-tin solder that has been adopted by more than 50 companies worldwide.

  11. Decontaminating lead bricks and shielding

    SciTech Connect (OSTI)

    Lussiez, G.

    1994-02-01T23:59:59.000Z

    Lead used for shielding is often surface contaminated with radioisotopes and is therefore a RCRA D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Laboratory decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 50 tons and likely to grow substantially of planned decommissioning operations. Thus lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for contaminated lead is removing the superficial layer of contamination with an abrasive medium under pressure. For lead, a mixture of alumina with water and air at about 40 psig rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a scaled-off area. The slurry of abrasive and particles of lead falls through a floor and is collected in a sump. A pump sends the slurry mixture back to the spray gun, creating a continuous process. The process generates small volumes of lead slurry that can be solidified and, because it passes the TCLP, is not a mixed waste. The decontaminated lead can be released for recycling.

  12. Decontaminating lead bricks and shielding

    SciTech Connect (OSTI)

    Lussiez, G.W.

    1993-05-01T23:59:59.000Z

    Lead used for shielding is often surface contaminated with radioisotopes and is therefore a RCRA D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Laboratory decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 50 tons and likely to grow substantially because of planned decommissioning operations. This lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for decontaminating lead is removing the thin superficial layer of contamination with an abrasive medium trader pressure. For lead, a mixture of alumina with water and air at about 40 psig rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a sealed-off area. The slurry of abrasive and particles of lead falls through a floor grating and is collected in a sump. A pump sends the slurry mixture back to the spray gun, creating a continuous process. The process generates small volumes of contaminated lead slurry that can be solidified and, because it passes the TCLP, is not a mixed waste. The decontaminated lead can be released for recycling.

  13. Decontaminating lead bricks and shielding

    SciTech Connect (OSTI)

    Lussiez, G.W.

    1993-01-01T23:59:59.000Z

    Lead used for shielding is often surface contaminated with radioisotopes and is therefore a RCRA D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Laboratory decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 50 tons and likely to grow substantially because of planned decommissioning operations. This lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for decontaminating lead is removing the thin superficial layer of contamination with an abrasive medium trader pressure. For lead, a mixture of alumina with water and air at about 40 psig rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a sealed-off area. The slurry of abrasive and particles of lead falls through a floor grating and is collected in a sump. A pump sends the slurry mixture back to the spray gun, creating a continuous process. The process generates small volumes of contaminated lead slurry that can be solidified and, because it passes the TCLP, is not a mixed waste. The decontaminated lead can be released for recycling.

  14. High temperature superconductor current leads

    DOE Patents [OSTI]

    Hull, J.R.; Poeppel, R.B.

    1995-06-20T23:59:59.000Z

    An electrical lead is disclosed having one end for connection to an apparatus in a cryogenic environment and the other end for connection to an apparatus outside the cryogenic environment. The electrical lead includes a high temperature superconductor wire and an electrically conductive material distributed therein, where the conductive material is present at the one end of the lead at a concentration in the range of from 0 to about 3% by volume, and at the other end of the lead at a concentration of less than about 20% by volume. Various embodiments are shown for groups of high temperature superconductor wires and sheaths. 9 figs.

  15. LEADING ADULT SQUAWFISH (Ptychocheilus oregonensis)

    E-Print Network [OSTI]

    of Federal, State or cooperating agencies and in processed form for economy and to avoid delay in publicationLEADING ADULT SQUAWFISH (Ptychocheilus oregonensis) WITHIN AN ELECTRIC FIELD Marine Biological, Arnie J. Suomela, Commissioner LEADING ADULT SQUAWFISH ( PTYCHOCHEILUS OREGONENSIS ) WITHIN AN ELECTRIC

  16. Lead reduction in ambient air

    SciTech Connect (OSTI)

    Smith, R.D.; Kiehn, O.A.; Wilburn, D.R.; Bowyer, R.C.

    1987-01-01T23:59:59.000Z

    The Bureau of Mines evaluated the emission control methods, including the capital investments and operating cost, necessary for further reducing lead levels in ambient air at the Glover, Herculaneum, and Buick smelter-refineries in Missouri and the East Helena, MT, smelter. This report presents theoretically achievable lead emission reductions and estimated capital and operating costs.

  17. Electrochemical behavior of lead telluride

    SciTech Connect (OSTI)

    Danilova, M.G.; Sveshnikova, L.L.; Repinskii, S.M.

    1987-07-01T23:59:59.000Z

    The electrochemical behavior of lead telluride was studied in acidic, neutral, and alkaline solutions. It was shown that in the case of anodic polarization in 1 M NaOH the PbTe surface composition is nearly stoichiometric. During cathodic polarization in 1 M NaOH and during anodic polarization in 1 M HCl the surface layer is lead-rich. In the case of anodic polarization in 1 M HCl the surface is tellurium-rich. Cathodic polarization in 1 M NaCl leads to tellurium depletion of the surface layer. Reaction equations describing the electrochemical processes at the PbTe electrode are reported.

  18. NATIONAL LEAD COMPANY OF OHIO

    Office of Legacy Management (LM)

    t-t AL- 1. + T fi r,y* t ,.- . NATIONAL LEAD COMPANY OF OHIO Ofll i iy Ci)wp HEALTH AND SAFETY DIVISION - ANALYTICAL DEPT. ANALYTICAL DATA SHEET U-G b ;33y jl:tL G c-w &3(y I...

  19. Soluble Lead Flow Battery: Soluble Lead Flow Battery Technology

    SciTech Connect (OSTI)

    None

    2010-09-01T23:59:59.000Z

    GRIDS Project: General Atomics is developing a flow battery technology based on chemistry similar to that used in the traditional lead-acid battery found in nearly every car on the road today. Flow batteries store energy in chemicals that are held in tanks outside the battery. When the energy is needed, the chemicals are pumped through the battery. Using the same basic chemistry as a traditional battery but storing its energy outside of the cell allows for the use of very low cost materials. The goal is to develop a system that is far more durable than today’s lead-acid batteries, can be scaled to deliver megawatts of power, and which lowers the cost of energy storage below $100 per kilowatt hour.

  20. LEAD PAINT DISCLOSURE Housing built before 1978 may contain lead-based paint. Lead from paint, paint chips, and dust

    E-Print Network [OSTI]

    Royer, Dana

    Your Family from Lead In Your Home. All Wesleyan housing was built before 1978 with the exceptionLEAD PAINT DISCLOSURE Housing built before 1978 may contain lead-based paint. Lead from paint, paint chips, and dust can pose health hazards if not taken care of properly. Lead exposure is especially

  1. The LHC Lead Injector Chain

    E-Print Network [OSTI]

    Beuret, A; Blas, A; Burkhardt, H; Carli, Christian; Chanel, M; Fowler, A; Gourber-Pace, M; Hancock, S; Hourican, M; Hill, C E; Jowett, John M; Kahle, K; Küchler, D; Lombardi, A M; Mahner, E; Manglunki, Django; Martini, M; Maury, S; Pedersen, F; Raich, U; Rossi, C; Royer, J P; Schindl, Karlheinz; Scrivens, R; Sermeus, L; Shaposhnikova, Elena; Tranquille, G; Vretenar, Maurizio; Zickler, T

    2004-01-01T23:59:59.000Z

    A sizeable part of the LHC physics programme foresees lead-lead collisions with a design luminosity of 1027 cm-2 s-1. This will be achieved after an upgrade of the ion injector chain comprising Linac3, LEIR, PS and SPS machines [1,2]. Each LHC ring will be filled in 10 min by almost 600 bunches, each of 7×107 lead ions. Central to the scheme is the Low Energy Ion Ring (LEIR) [3,4], which transforms long pulses from Linac3 into high-brilliance bunches by means of multi-turn injection, electron cooling and accumulation. Major limitations along the chain, including space charge, intrabeam scattering, vacuum issues and emittance preservation are highlighted. The conversion from LEAR (Low Energy Antiproton Ring) to LEIR involves new magnets and power converters, high-current electron cooling, broadband RF cavities, and a UHV vacuum system with getter (NEG) coatings to achieve a few 10-12 mbar. Major hardware changes in Linac3 and the PS are also covered. An early ion scheme with fewer bunches (but each at nominal...

  2. Where Is Lead Found? Paint in many homes built before 1978 may contain lead.

    E-Print Network [OSTI]

    Liskiewicz, Maciej

    in lead crystal or lead-glazed pottery may contain lead. Where Is Lead Most Likely to Be a Hazard on toys and furniture -- especially if antique or imported -- may contain lead. · Food or liquids stored

  3. Nick Wright Named Advanced Technologies Group Lead

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nick Wright Named Advanced Technologies Group Lead Nick Wright Named Advanced Technologies Group Lead February 4, 2013 Nick Nick Wright has been named head of the National Energy...

  4. NERSC seeks Computational Systems Group Lead

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    seeks Computational Systems Group Lead NERSC seeks Computational Systems Group Lead January 6, 2011 by Katie Antypas Note: This position is now closed. The Computational Systems...

  5. Distributed Generation Lead-by-Example Resources

    Broader source: Energy.gov [DOE]

    State governments can lead by example by promoting renewable energy programs and policies. Efforts to lead by example include using renewable energy resources (including alternative fuel for...

  6. Multi-lead heat sink

    DOE Patents [OSTI]

    Roose, Lars D. (Albuquerque, NM)

    1984-01-01T23:59:59.000Z

    The disclosure relates to a heat sink used to protect integrated circuits from the heat resulting from soldering them to circuit boards. A tubular housing contains a slidable member which engages somewhat inwardly extending connecting rods, each of which is rotatably attached at one end to the bottom of the housing. The other end of each rod is fastened to an expandable coil spring loop. As the member is pushed downward in the housing, its bottom edge engages and forces outward the connecting rods, thereby expanding the spring so that it will fit over an integrated circuit. After the device is in place, the member is slid upward and the spring contracts about the leads of the integrated circuit. Soldering is now conducted and the spring absorbs excess heat therefrom to protect the integrated circuit. The placement steps are repeated in reverse order to remove the heat sink for use again.

  7. Multi-lead heat sink

    DOE Patents [OSTI]

    Roose, L.D.

    1982-08-25T23:59:59.000Z

    The disclosure relates to a heat sink used to protect integrated circuits from the heat resulting from soldering them to circuit boards. A tubular housing contains a slidable member which engages somewhat inwardly extending connecting rods, each of which is rotatably attached at one end to the bottom of the housing. The other end of each rod is fastened to an expandable coil spring loop. As the member is pushed downward in the housing, its bottom edge engages and forces outward the connecting rods, thereby expanding the spring so that it will fit over an integrated circuit. After the device is in place, the member is slid upward and the spring contracts about the leads of the integrated circuit. Soldering is now conducted and the spring absorbs excess heat therefrom to protect the integrated circuit. The placement steps are repeated in reverse order to remove the heat sink for use again.

  8. Multi-lead heat sink

    DOE Patents [OSTI]

    Roose, L.D.

    1984-07-03T23:59:59.000Z

    The disclosure relates to a heat sink used to protect integrated circuits from the heat resulting from soldering them to circuit boards. A tubular housing contains a slidable member which engages somewhat inwardly extending connecting rods, each of which is rotatably attached at one end to the bottom of the housing. The other end of each rod is fastened to an expandable coil spring loop. As the member is pushed downward in the housing, its bottom edge engages and forces outward the connecting rods, thereby expanding the spring so that it will fit over an integrated circuit. After the device is in place, the member is slid upward and the spring contracts about the leads of the integrated circuit. Soldering is now conducted and the spring absorbs excess heat therefrom to protect the integrated circuit. The placement steps are repeated in reverse order to remove the heat sink for use again. 4 figs.

  9. Lead Safety Awareness This Bulletin provides information on the safe handling of lead

    E-Print Network [OSTI]

    . CONTROLLING THE HAZARDS: LEAD STORAGE · Use inventory tracking to facilitate proper lead storage and to keep lead inventories to a minimum. · Store lead in containers or covered in specially designed areas. · Routinely monitor lead inventories to check for lead dust contamination. GENERAL GOOD WORK PRACTICES · When

  10. Children and lead: new findings and concerns

    SciTech Connect (OSTI)

    Lin-Fu, J.S.

    1982-09-02T23:59:59.000Z

    An editorial dealing with lead in the environment and its health risks to children is presented. Young children are particularly vulnerable to lead exposure. Through hand-to-mouth activities, such as thumb sucking, nail biting, or eating with dirty hands, lead in house dust and garden soil readily enters their bodies. Children with pica are exposed to more lead because they eat such items as paint chips, broken plaster, and dirt. Moreover, intestinal lead absorption is greater in children than in adults. The author recommends a concerted effort to reduce undue lead absorption in children. (JMT)

  11. Australia and New Zealand Coordinating Lead Authors

    E-Print Network [OSTI]

    Green, Donna

    11 Australia and New Zealand Coordinating Lead Authors: Kevin Hennessy (Australia), Blair Fitzharris (New Zealand) Lead Authors: Bryson C. Bates (Australia), Nick Harvey (Australia), Mark Howden (Australia), Lesley Hughes (Australia), Jim Salinger (New Zealand), Richard Warrick (New Zealand

  12. Energy Policy 29 (2001) 11331143 Ethanol as a lead replacement: phasing out leaded gasoline in Africa

    E-Print Network [OSTI]

    Thomas, Valerie

    Energy Policy 29 (2001) 1133­1143 Ethanol as a lead replacement: phasing out leaded gasoline cost of lead additives and of gasoline, and the falling cost of ethanol and sugarcane, have created sugarcane is produced in Africa to replace all the lead used in African gasoline; this would require Africa

  13. Procurement Standards Lead-by-Example Resources

    Broader source: Energy.gov [DOE]

    State and local governments can lead by example by promoting energy efficiency programs and policies for public facilities, equipment, and government operations.

  14. Energy Efficiency Lead-by-Example Resources

    Broader source: Energy.gov [DOE]

    State and local governments can lead by example by promoting energy efficiency programs and policies for public facilities, equipment, and government operations.

  15. Lead by Example with Smart Energy Management

    SciTech Connect (OSTI)

    Not Available

    2006-07-01T23:59:59.000Z

    The Lead by Example with Smart Energy Management brochure describes FEMP's services, namely financing and acquisition support, technical assistance and policy, and outreach and coordination.

  16. Imnaha Subbasin Inventory Subbasin Lead Entity

    E-Print Network [OSTI]

    Imnaha Subbasin Inventory May 2004 Written by Ecovista Subbasin Lead Entity: Nez Perce Tribe.......................................................................... 15 List of Tables TABLE 1. ACRONYMS USED IN THE IMNAHA SUBBASIN INVENTORY

  17. LEAD COMMISSIONER REPORT RENEWABLE POWER IN

    E-Print Network [OSTI]

    , Public Interest Energy Research Program, Public Utilities Regulatory Policies Act, Renewable Energy1502011002LCFREV1 #12;CALIFORNIA ENERGY COMMISSION 2011 INTEGRATED ENERGY POLICY REPORT LEAD COMMISSIONER of the 2011 Integrated Energy Policy Report Lead Commissioner. It does not necessarily represent the views

  18. LEAD Academy *Leadership in Educational Administration Academy

    E-Print Network [OSTI]

    Farritor, Shane

    LEAD Academy *Leadership in Educational Administration Academy Educational Administration for overnight accommodations if desired A time intensive component of the academy will occur on the UNO campus of practitioners will serve to facilitate the LEAD Academy, developing mentor/mentee networks that will continue

  19. EPA Lead Safety for Renovation, Repair and

    E-Print Network [OSTI]

    Tennessee, University of

    than 20 f lead-based paint is dis- e exterior. Window replace- onsidered minor mainte- air. If you're of thousands of dollars in fines and put yourself and your company at risk of po- tential lawsuits. 2. ProtectEPA Lead Safety for Renovation, Repair and Painting (RRP) Course Certified Renovators Class

  20. Fan-fold shielded electrical leads

    DOE Patents [OSTI]

    Rohatgi, R.R.; Cowan, T.E.

    1996-06-11T23:59:59.000Z

    Disclosed are fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figs.

  1. Fan-fold shielded electrical leads

    DOE Patents [OSTI]

    Rohatgi, Rajeev R. (Mountain View, CA); Cowan, Thomas E. (Livermore, CA)

    1996-01-01T23:59:59.000Z

    Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate.

  2. Corrosion by liquid lead and lead-bismuth: experimental results review and analysis

    SciTech Connect (OSTI)

    Zhang, Jinsuo [Los Alamos National Laboratory

    2008-01-01T23:59:59.000Z

    Liquid metal technologies for liquid lead and lead-bismuth alloy are under wide investigation and development for advanced nuclear energy systems and waste transmutation systems. Material corrosion is one of the main issues studied a lot recently in the development of the liquid metal technology. This study reviews corrosion by liquid lead and lead bismuth, including the corrosion mechanisms, corrosion inhibitor and the formation of the protective oxide layer. The available experimental data are analyzed by using a corrosion model in which the oxidation and scale removal are coupled. Based on the model, long-term behaviors of steels in liquid lead and lead-bismuth are predictable. This report provides information for the selection of structural materials for typical nuclear reactor coolant systems when selecting liquid lead or lead bismuth as heat transfer media.

  3. Sustainability Peer Educator Group Lead Positions Position: Sustainability Peer Educators Group Lead

    E-Print Network [OSTI]

    Boonstra, Rudy

    Sustainability Peer Educator Group Lead Positions Position: Sustainability Peer Educators Group times) Term of position: September 2013 ­ April 2014 Position Summary: Working with the Sustainability Project Coordinator, the Sustainability Peer Educator Group Leads will be responsible

  4. Lightweight, durable lead-acid batteries

    DOE Patents [OSTI]

    Lara-Curzio, Edgar (Lenoir City, TN); An, Ke (Knoxville, TX); Kiggans, Jr., James O. (Oak Ridge, TN); Dudney, Nancy J. (Knoxville, TN); Contescu, Cristian I. (Knoxville, TN); Baker, Frederick S. (Oak Ridge, TN); Armstrong, Beth L. (Clinton, TN)

    2011-09-13T23:59:59.000Z

    A lightweight, durable lead-acid battery is disclosed. Alternative electrode materials and configurations are used to reduce weight, to increase material utilization and to extend service life. The electrode can include a current collector having a buffer layer in contact with the current collector and an electrochemically active material in contact with the buffer layer. In one form, the buffer layer includes a carbide, and the current collector includes carbon fibers having the buffer layer. The buffer layer can include a carbide and/or a noble metal selected from of gold, silver, tantalum, platinum, palladium and rhodium. When the electrode is to be used in a lead-acid battery, the electrochemically active material is selected from metallic lead (for a negative electrode) or lead peroxide (for a positive electrode).

  5. Lightweight, durable lead-acid batteries

    SciTech Connect (OSTI)

    Lara-Curzio, Edgar; An, Ke; Kiggans, Jr., James O; Dudney, Nancy J; Contescu, Cristian I; Baker, Frederick S; Armstrong, Beth L

    2013-05-21T23:59:59.000Z

    A lightweight, durable lead-acid battery is disclosed. Alternative electrode materials and configurations are used to reduce weight, to increase material utilization and to extend service life. The electrode can include a current collector having a buffer layer in contact with the current collector and an electrochemically active material in contact with the buffer layer. In one form, the buffer layer includes a carbide, and the current collector includes carbon fibers having the buffer layer. The buffer layer can include a carbide and/or a noble metal selected from of gold, silver, tantalum, platinum, palladium and rhodium. When the electrode is to be used in a lead-acid battery, the electrochemically active material is selected from metallic lead (for a negative electrode) or lead peroxide (for a positive electrode).

  6. INEEL Lead Recycling in a Moratorium Environment

    SciTech Connect (OSTI)

    Kooda, K. E.; Galloway, K.; McCray, C. W.; Aitken, D. W.

    2003-02-26T23:59:59.000Z

    Since 1999, the Idaho National Engineering and Environmental Laboratory (INEEL) Lead Project successfully recycled over 700,000 pounds of excess INEEL lead to the private sector. On February 14, 2000, the Secretary of Energy, Bill Richardson, formalized the January 12, 2000, moratorium on recycling radioactive scrap metal that prevented the unrestricted release of recycled scrap metals to the private sector. This moratorium created significant problems for the INEEL lead recycling program and associated plans; however, through the cooperative efforts of the INEEL and Idaho State University as well as innovative planning and creative thinking the recycling issues were resolved. This collaboration has recycled over 160,000 pounds of excess lead to Idaho State University with a cost savings of over $.5M.

  7. INEEL Lead Recycling in a Moratorium Environment

    SciTech Connect (OSTI)

    Kooda, Kevin Evan; Mc Cray, Casey William; Aitken, Darren William; Galloway, Kelly

    2003-02-01T23:59:59.000Z

    Since 1999, the Idaho National Engineering and Environmental Laboratory (INEEL) Lead Project successfully recycled over 700,000 pounds of excess INEEL lead to the private sector. On February 14, 2000, the Secretary of Energy, Bill Richardson, formalized the January 12, 2000, moratorium on recycling radioactive scrap metal that prevented the unrestricted release of recycled scrap metals to the private sector. This moratorium created significant problems for the INEEL lead recycling program and associated plans; however, through the cooperative efforts of the INEEL and Idaho State University as well as innovative planning and creative thinking the recycling issues were resolved. This collaboration has recycled over 160,000 pounds of excess lead to Idaho State University with a cost savings of over $.5M.

  8. Imnaha Subbasin Management Plan Subbasin Lead Entity

    E-Print Network [OSTI]

    Imnaha Subbasin Management Plan May 2004 Written by Ecovista Subbasin Lead Entity: Nez Perce Tribe....................................................................................... 6 1.2.4 Ecovista Website Information.......................................................................... 59 4.3 Terrestrial Data and Information Gaps

  9. Saturnine curse: a history of lead poisoning

    SciTech Connect (OSTI)

    Green, D.W.

    1985-01-01T23:59:59.000Z

    Over the past ten years there has been increasing recognition of subacute and chronic lead poisoning and a growing awareness of its pathophysiology and clinical effects. Besides the classic manifestations of abdominal colic, seizures, and anemia progressing to gout, renal disease, and neuropathy, more subtle manifestations are now being increasingly recognized, such as the development of hypertension, neurobehavioral changes, reproductive and endocrine abnormalities, a possible role in carcinogenesis, and an overall increase in morbidity and mortality. Lead was one of the seven metals of antiquity, and it has accompanied the Eurasian and American civilizations since their beginnings. Lead is an extremely pernicious metal with a multitude of adverse effects. The recurring nature of lead poisoning throughout the development of civilization can truly be referred to as the saturnine curse. 16 references.

  10. Primer on lead-acid storage batteries

    SciTech Connect (OSTI)

    NONE

    1995-09-01T23:59:59.000Z

    This handbook was developed to help DOE facility contractors prevent accidents caused during operation and maintenance of lead-acid storage batteries. Major types of lead-acid storage batteries are discussed as well as their operation, application, selection, maintenance, and disposal (storage, transportation, as well). Safety hazards and precautions are discussed in the section on battery maintenance. References to industry standards are included for selection, maintenance, and disposal.

  11. Information from leading neutrons at HERA

    E-Print Network [OSTI]

    V. A. Khoze; A. D. Martin; M. G. Ryskin

    2006-06-20T23:59:59.000Z

    In principle, leading neutrons produced in photoproduction and deep-inelastic scattering at HERA have the potential to determine the pion structure function, the neutron absorptive cross section and the form of the pion flux. To explore this potential we compare theoretical predictions for the x_L and p_t spectra of leading neutrons, and the Q^2 dependence of the cross section, with the existing ZEUS data.

  12. Synthesis of the entire standard lead electrocardiogram by transformation from a subset of the standard leads

    E-Print Network [OSTI]

    Vallhonrat, Juan Braulio

    1966-01-01T23:59:59.000Z

    in dimensionless form. An individual element r&& in the correlation matrix R will be the correlation coefficient th th between the i and ] variables. The principal components are the eigenvectors of the correlation matrix and the corresponding eigen- values...) and using the other lead as an exploring lead. Another classification is based on the location of the lead, that is, direct, semi-direct, or indirect. A direct lead is placed on the heart, an indirect lead is placed at a body surface location distant from...

  13. Thermoforming plastic in lead shield construction

    SciTech Connect (OSTI)

    Abrahams, M.E.; Chow, C.H.; Loyd, M.D. (Univ. of Texas Medical Branch, Galveston (USA))

    1989-09-01T23:59:59.000Z

    Radiation treatments using low energy X-rays or electrons frequently require a final field defining shield to be placed on the patient's skin. A custom made lead cut-out is used to provide a close fit to a particular patient's surface contours. We have developed a procedure which utilizes POLYFORM thermoplastic to obtain a negative mold of the patient instead of the traditional plaster bandage or dental impression gel. The Polyform is softened in warm water, molded carefully over the patient's surface, and is removed when set or hardened, usually within five minutes. Then lead sheet cut-outs can be formed within this negative. For shielding cut-outs requiring thicker lead sheet, a positive is made from dental stone using this Polyform negative. We have found this procedure to be neat, fast and comfortable for both patient and the dosimetrist.

  14. Leading Edge Bacterial Genomics and Pathogen Evolution

    E-Print Network [OSTI]

    Mekalanos, John

    Leading Edge Review Bacterial Genomics and Pathogen Evolution David M. Raskin,1 Rekha Seshadri,2 Medical School, Boston, MA 02115, USA 2 The Institute for Genomic Research, 9712 Medical Center Drive.02.002 The availability of hundreds of bacterial genome sequences has altered the study of bacte- rial pathogenesis

  15. Mechanisms leading to electrically isolated cell

    E-Print Network [OSTI]

    Mechanisms leading to electrically isolated cell parts and power loss under mechanical loads F cracks are omnipresent #12;Power loss by cell cracks Humidity freeze cycle 0 50 100 150 200 Powerloss, isolated cell area Crack mode: #12;Power loss after mechanical load · Some solar cells with mode A cracks

  16. Analyzing lead information from SAR images

    E-Print Network [OSTI]

    Van Dyne, M. M.; Tsatsoulis, Costas; Fetterer, F.

    1998-03-01T23:59:59.000Z

    means of gathering important information about the sea ice cover and its climatic influence, This paper describes: 1) a method for extracting and analyzing leads from ERS-1 synthetic aperture radar (SAR) images classified by ice type and 2) the results...

  17. Inadvertent Climate Modification Due to Anthropogenic Lead

    SciTech Connect (OSTI)

    Cziczo, Daniel J.; Stetzer, Olaf; Worringen, Annette; Ebert, Martin; Weinbruch, Stephan; Kamphus, M.; Gallavardin, S. J.; Curtius, J.; Borrmann, S.; Froyd, Karl D.; Mertes, S.; Mohler, Ottmar; Lohmann, U.

    2009-05-01T23:59:59.000Z

    The relationship between atmospheric particulate matter and the formation of clouds is among the most uncertain aspects of our current understanding of climate change1. One specific question that remains unanswered is how anthropogenic particulate emissions are affecting the nucleation of ice crystals. Satellites show ice clouds cover more than a third of the globe2 and models suggest that ice nucleation initiates the majority of terrestrial precipitation3. It is therefore not possible to adequately understand either climate change or the global water cycle without understanding ice nucleation. Here we show that lead-containing particles are among the most efficient ice nucleating substances commonly found in the atmosphere. Field observations were conducted with mass spectrometry and electron microscopy at two remote stations on different continents, far removed from local emissions. Laboratory studies within two cloud chambers using controlled experimental conditions support the field data. Because the dominate sources of particulate lead are anthropogenic emissions such as aviation fuel, power generation, smelting, and the re-suspension of residue from tetra-ethyl leaded gasoline4, it is likely that cloud formation and precipitation have been affected when compared to pre-industrial times. A global climate model comparing pre-industrial and anthropogenically perturbed conditions shows that lead-containing particles may be increasing the outgoing longwave radiation by 0.2 to 0.8 W m-2, thereby offsetting a portion of the warming attributed to greenhouse gases1.

  18. The Commonwealth's Leading College of Engineering

    E-Print Network [OSTI]

    Virginia Tech

    and Ocean Engineering....................540-231-6611 Biological Systems EngineeringThe Commonwealth's Leading College of Engineering is at Virginia Tech Faculty ExpErtisE GuidE 2012-2014 Virginia Tech engineering students won the international EcoCAR Challenge, a 3-year design competition

  19. Felix Wrsten ETH Zurich enjoys a leading

    E-Print Network [OSTI]

    Leonardo, Degiorgi

    Felix WĂĽrsten ETH Zurich enjoys a leading position in the quantum sciences. The Executive Board now research in this area. "ETH Zurich has secured it- self a good starting position and now wishes to use physics will become the tool of the engineer." Fundamental development Together with the ETH Zurich Foun

  20. Quality Support G. Q. Kirk, Lead (4)

    E-Print Network [OSTI]

    ) Quality Systems and Services Division February 11, 2011 Operations Analysis E. L. Griffis L. R. Brown, Secy. Systems Engineering Y. S. Kwon, Manager HFIR Maintenance D. H. AbercQuality Support G. Q. Kirk, Lead (4) R. L. Bullock (4) A. C. Hendricks (4) G. H. Henkel (4) D. L

  1. Lead in Your Drinking Water Lead (Pb) is an extremely toxic heavy metal that unfortunately occurs widely in

    E-Print Network [OSTI]

    Maynard, J. Barry

    Lead in Your Drinking Water Lead (Pb) is an extremely toxic heavy metal that unfortunately occurs of metallic lead in the soil (4) Drinking water ­ water as it leaves the treatment plant has no lead plumbing components Your exposure to lead in drinking water is at the faucet, but the lead can come from

  2. Towards modeling gadolinium-lead-borate glasses

    SciTech Connect (OSTI)

    Rada, S., E-mail: Simona.Rada@phys.utcluj.ro [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Ristoiu, T. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Rada, M. [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Coroiu, I. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Maties, V. [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Culea, E. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)] [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)

    2010-01-15T23:59:59.000Z

    Infrared spectra of gadolinium-lead-borate glasses of the xGd{sub 2}O{sub 3}.(100 - x)[3B{sub 2}O{sub 3}.PbO] system, where x = 0, 5, 10, 15, 25, 35 and 50 mol.%, have been recorded to explore the role of content of gadolinium ions behaving as glass modifier. The FTIR spectroscopy data for the xGd{sub 2}O{sub 3}.(1 - x)[3B{sub 2}O{sub 3}.PbO] glasses show the structural role of lead ions as a network-formers and of the gadolinium ions network modifiers. Adding of the rare earth ion up to 35 mol.% into the glass matrix, the IR bands characteristic to the studied glasses become sharper and more pronounced. Structural changes, as recognized by analyzing band shapes of IR spectra, revealed that Gd{sub 2}O{sub 3} causes a change from the continuous borate network to the continuous lead-borate network interconnected through Pb-O-B and B-O-B bridges and the transformation of some tetrahedral [BO{sub 4}] units into trigonal [BO{sub 3}] units. Then, gadolinium ions have affinity towards [BO{sub 3}] structural units which contain non-bridging oxygens necessary for the charge compensation because the more electronegative [BO{sub 3}] structural units were implied in the formation of B-O-Gd bonds and the transformation of glass network into a glass ceramic. We propose a possible structural model of building blocks for the formation of continuous random 3B{sub 2}O{sub 3}.PbO network glass used by density functional theory (DFT) calculations. DFT calculations show that lead atoms occupy three different sites in the proposed model. The first is coordinated with six oxygen atoms forming distorted octahedral geometries. The second lead atom has an octahedral oxygen environment and the five longer Pb-O bonds are considered as participating in the metal coordination scheme. The third lead atom has ionic character. In agreement with the results offered by the experimental FTIR data, the theoretical IR data confirm that our proposed structure is highly possible.

  3. CBER-DETR Nevada Coincident and Leading Employment Leading Index Hits Bump in the Road

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Leading Index Hits Bump in the Road The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index

  4. CBER-DETR Nevada Coincident and Leading Employment Coincident Index Rises, Leading Index Pauses

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Coincident Index Rises, Leading Index Pauses The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using

  5. Lead magnesium niobate actuator for micropositioning

    DOE Patents [OSTI]

    Swift, Charles D. (Livermore, CA); Bergum, John W. (Concord, CA)

    1994-01-01T23:59:59.000Z

    An improved lead magnesium niobate actuator is disclosed comprising a cylindrical lead magnesium niobate crystal stack mounted in a cylindrical casing wherein a bias means, such as one or more belleville washers, is located between one end of the crystal stack and a partially closed end of the casing; and adjustment means are provided which bear against the opposite end of the crystal stack, whereby an adjustable compressive force is constantly applied against the crystal stack, whether the crystal stack is actuated in an extended position, or is in an unactuated contracted position. In a preferred embodiment, cooling ports are provided for the circulation of coolant in the actuator to cool the crystal stack, and provision is made for removal and replacement of the crystal stack without disconnecting the actuator from the external device being actuated.

  6. Lead magnesium niobate actuator for micropositioning

    DOE Patents [OSTI]

    Swift, C.D.; Bergum, J.W.

    1994-10-25T23:59:59.000Z

    An improved lead magnesium niobate actuator is disclosed comprising a cylindrical lead magnesium niobate crystal stack mounted in a cylindrical casing wherein a bias means, such as one or more belleville washers, is located between one end of the crystal stack and a partially closed end of the casing; and adjustment means are provided which bear against the opposite end of the crystal stack, whereby an adjustable compressive force is constantly applied against the crystal stack, whether the crystal stack is actuated in an extended position, or is in an unactuated contracted position. In a preferred embodiment, cooling ports are provided for the circulation of coolant in the actuator to cool the crystal stack, and provision is made for removal and replacement of the crystal stack without disconnecting the actuator from the external device being actuated. 3 figs.

  7. AVTA: 2010 Toyota Prius Gen III HEV Testing Results | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up fromDepartment of Energy 601 High26-OPAM63-OPAMGuidanceAVTASmart Fortwo

  8. Microsoft Word - TM-2010-253 - 2010 Prius Report - 26 - Tim - edited 2-16-2011

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinan antagonist Journal Article: Crystal structureComposite--FORRemarksHEATINGI5613, Rev.QA:4135-Rev. 111

  9. Energy, Appliances and Utilities Energy&Environment * EnergySTAR * Toyota PRIUS Myths, Facts, and Hype ...

    E-Print Network [OSTI]

    Kostic, Milivoje M.

    below) Typical furnace: 1 therm/hr = 100000 BTU/hr = 29.3 kW(h) heating power Typical A/C unit: 3.5 ton therm = 100000 BTU = 29.307 kWhr 1 tonR = 12000 BTU/hr = 3.516 kW(c) cooling rate 1 SEER = (1 BTU)/Whr(e) = 1000 BTU/kWhr = 0.293 kWhr(c)/kWhr(e), i.e., (cooling)/(electrical) ratio What is SEER? How does

  10. Preliminary synchrotron analysis of lead in hair from a lead smelter worker

    SciTech Connect (OSTI)

    Martin, R.R.; Kempson, I.M.; Naftel, S.J.; Skinner, W.M. (Case Western); (U. South Australia)

    2008-06-09T23:59:59.000Z

    Synchrotron X-ray fluorescence has been used to study the distribution of lead in a hair sample collected from a lead smelter worker. A mathematical model was used to imitate the transverse scan signal based on the analysis volume and concentration profiles. The results suggest that the Pb originates both from ingestion and environmental exposure, however direct deposition from the environment is the more important source of hair lead. The model could apply equally to any other analysis involving a thin cylindrical sample.

  11. XRD, lead equivalent and UV-VIS properties study of Ce and Pr lead silicate glasses

    SciTech Connect (OSTI)

    Alias, Nor Hayati, E-mail: norhayati@nuclearmalaysia.gov.my; Abdullah, Wan Shafie Wan, E-mail: norhayati@nuclearmalaysia.gov.my; Isa, Norriza Mohd, E-mail: norhayati@nuclearmalaysia.gov.my; Isa, Muhammad Jamal Md, E-mail: norhayati@nuclearmalaysia.gov.my; Zali, Nurazila Mat; Abdullah, Nuhaslinda Ee [Malaysian Nuclear Agency, 43000, Bangi, Kajang, Selangor (Malaysia); Muhammad, Azali [Malaysian Society for Non-Destructive Testing (Malaysia)

    2014-02-12T23:59:59.000Z

    In this work, Cerium (Ce) and Praseodymium (Pr) containing lead silicate glasses were produced with 2 different molar ratios low (0.2 wt%) and high (0.4wt%). These types of glasses can satisfy the characteristics required for radiation shielding glasses and minimize the lead composition in glass. The radiation shielding properties of the synthesized glasses is explained in the form of lead equivalent study. The XRD diffraction and UV-VIS analysis were performed to observe the structural changes of the synthesis glasses at 1.5 Gy gamma radiation exposures.

  12. Know the Facts Lead poisoning is caused by swallowing or

    E-Print Network [OSTI]

    ;Protect Your Family 1. Test your home for lead. · If you live in a home built before 1978, have your home are most at risk. If you are pregnant, lead can harm your baby. Lead can cause learning and behavior on their hands and toys. FACT A lead test is the only way to know if your child has lead poisoning. Most

  13. Lead Screening for NH Soils: Minimizing Health Risks

    E-Print Network [OSTI]

    New Hampshire, University of

    family. On your soil test report, if the lead screening levels are elevated, you will receive in populated areas include the use of lead paint around homes (pre- 1970s), the use of lead-arsenate for pest does a "lead screening" test that indicates whether or not lead could pose a health risk for your

  14. Asian anthropogenic lead contamination in the North Pacific Ocean as evidenced by stable lead isotopic compositions

    E-Print Network [OSTI]

    Zurbrick, Cheryl Marie

    2014-01-01T23:59:59.000Z

    and North Central Pacific Ocean. Deep Sea Res. Part II Top.Lead Within the Northwest Pacific Ocean Evidenced by Leadventilation flux of the Pacific Ocean. J. Geophys. Res. 106(

  15. Properties of lead-lithium solutions

    SciTech Connect (OSTI)

    Hoffman, N.J.; Darnell, A.; Blink, J.A.

    1980-10-01T23:59:59.000Z

    Lead-lithium solutions are of interest to liquid metal wall ICF reactor designers because Pb may be present to some extent in both heavy ion beam and laser-driven ICF targets; therefore, Pb will be present as an impurity in a flowing lithium wall. In addition, Pb-Li solutions containing approx. 80 a/o Pb are a strong candidate for a heavy ion beam driven HYLIFE converter and a viable alternative to a pure Li wall for a laser driven converter. The properties of Pb-Li solutions including the effect of hydrogen impurities are reviewed, and the reactor design implications are discussed.

  16. Lead Slowing Down Spectrometer Status Report

    SciTech Connect (OSTI)

    Warren, Glen A.; Anderson, Kevin K.; Bonebrake, Eric; Casella, Andrew M.; Danon, Yaron; Devlin, M.; Gavron, Victor A.; Haight, R. C.; Imel, G. R.; Kulisek, Jonathan A.; O'Donnell, J. M.; Weltz, Adam

    2012-06-07T23:59:59.000Z

    This report documents the progress that has been completed in the first half of FY2012 in the MPACT-funded Lead Slowing Down Spectrometer project. Significant progress has been made on the algorithm development. We have an improve understanding of the experimental responses in LSDS for fuel-related material. The calibration of the ultra-depleted uranium foils was completed, but the results are inconsistent from measurement to measurement. Future work includes developing a conceptual model of an LSDS system to assay plutonium in used fuel, improving agreement between simulations and measurement, design of a thorium fission chamber, and evaluation of additional detector techniques.

  17. Thermal conductivity of bulk nanostructured lead telluride

    SciTech Connect (OSTI)

    Hori, Takuma [Department of Mechanical Engineering, The University of Tokyo, Bunkyo, Tokyo 113-8656 (Japan); Chen, Gang [Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Shiomi, Junichiro, E-mail: shiomi@photon.t.u-tokyo.ac.jp [Department of Mechanical Engineering, The University of Tokyo, Bunkyo, Tokyo 113-8656 (Japan); PRESTO, Japan Science and Technology Agency, Kawaguchi, Saitama 332-0012 (Japan)

    2014-01-13T23:59:59.000Z

    Thermal conductivity of lead telluride with embedded nanoinclusions was studied using Monte Carlo simulations with intrinsic phonon transport properties obtained from first-principles-based lattice dynamics. The nanoinclusion/matrix interfaces were set to completely reflect phonons to model the maximum interface-phonon-scattering scenario. The simulations with the geometrical cross section and volume fraction of the nanoinclusions matched to those of the experiment show that the experiment has already reached the theoretical limit of thermal conductivity. The frequency-dependent analysis further identifies that the thermal conductivity reduction is dominantly attributed to scattering of low frequency phonons and demonstrates mutual adaptability of nanostructuring and local disordering.

  18. Non-lead hollow point bullet

    DOE Patents [OSTI]

    Vaughn, Norman L. (Knoxville, TN); Lowden, Richard A. (Clinton, TN)

    2003-04-15T23:59:59.000Z

    The non-lead hollow point bullet of the instant invention comprises a mixed construction slug further comprising, a monolithic metal insert having a tapered (preferred conical) hollow point tip and a tapered (preferred conical) tail protrusion, and an unsintered powdered metal composite core in tandem alignment with the insert. The core has a hollow tapered (preferred conical) cavity tip portion coupled with the tapered (preferred conical) tail protrusion on the insert. An open tip jacket envelops at least a portion of the insert and the core. The jacket is swaged at the open tip.

  19. Leading Edge Technologies Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429Lacey, Washington:Lakeville, MN)Lauderhill,5. ItLea Hill, Washington:Leading

  20. Richard Gerber! NERSC! User Services Group Lead

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared0 Resource Program September 2010 BRichardGroup Lead Debugging and

  1. Anthropogenic Lead Emissions in the Ocean: The Evolving Global Experiment

    E-Print Network [OSTI]

    Lee, Jong-Mi

    We review the current distribution of lead and lead isotopes in the ocean with regard to the evolving pattern of human emissions during the past decades and centuries.

  2. Combined Heat and Power System Enables 100% Reliability at Leading...

    Broader source: Energy.gov (indexed) [DOE]

    Enables 100% Reliability at Leading Medical Campus - Case Study, 2013 Combined Heat and Power System Enables 100% Reliability at Leading Medical Campus - Case Study, 2013 Thermal...

  3. Scheibe named lead scientist for EMSL computing | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    lead scientist for EMSL computing He will oversee Multiscale Modeling and High Performance Computing Tim Scheibe EMSL has selected Tim Scheibe as lead scientist for Multiscale...

  4. Research Led by Sandia Reveals Leading-Edge Erosion Significantly...

    Broader source: Energy.gov (indexed) [DOE]

    Research Led by Sandia Reveals Leading-Edge Erosion Significantly Reduces Wind Turbine Performance Research Led by Sandia Reveals Leading-Edge Erosion Significantly Reduces Wind...

  5. University of Maryland Wins Architecture Prize, Pulls Into Lead...

    Broader source: Energy.gov (indexed) [DOE]

    Maryland Wins Architecture Prize, Pulls Into Lead in 2011 Solar Decathlon University of Maryland Wins Architecture Prize, Pulls Into Lead in 2011 Solar Decathlon September 28, 2011...

  6. Electrochemical Sensors for the Detection of Lead and Other Toxic...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sensors for the Detection of Lead and Other Toxic Heavy Metals: The Next Generation of Personal Exposure Electrochemical Sensors for the Detection of Lead and Other Toxic Heavy...

  7. Hydrogen diffusion in Lead Zirconate Titanate and Barium Titanate...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    diffusion in Lead Zirconate Titanate and Barium Titanate. Hydrogen diffusion in Lead Zirconate Titanate and Barium Titanate. Abstract: Hydrogen is a potential clean-burning,...

  8. New Superconducting Magnet Will Lead to Next Generation of Wind...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New Superconducting Magnet Will Lead to Next Generation of Wind Turbine Generators New Superconducting Magnet Will Lead to Next Generation of Wind Turbine Generators September 12,...

  9. Dow Chemical Company: Assessment Leads to Steam System Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dow Chemical Company: Assessment Leads to Steam System Energy Savings in a Petrochemical Plant Dow Chemical Company: Assessment Leads to Steam System Energy Savings in a...

  10. Lead Slowing Down Spectrometer Research Plans

    SciTech Connect (OSTI)

    Warren, Glen A.; Kulisek, Jonathan A.; Gavron, Victor; Danon, Yaron; Weltz, Adam; Harris, Jason; Stewart, T.

    2013-03-22T23:59:59.000Z

    The MPACT-funded Lead Slowing Down Spectrometry (LSDS) project has been evaluating the feasibility of using LSDS techniques to assay fissile isotopes in used nuclear fuel assemblies. The approach has the potential to provide considerable improvement in the assay of fissile isotopic masses in fuel assemblies compared to other non-destructive techniques in a direct and independent manner. The LSDS collaborations suggests that the next step to in empirically testing the feasibility is to conduct measurements on fresh fuel assemblies to understand investigate self-attenuation and fresh mixed-oxide (MOX) fuel rodlets so we may betterto understand extraction of masses for 235U and 239Pu. While progressing toward these goals, the collaboration also strongly suggests the continued development of enabling technology such as detector development and algorithm development, thatwhich could provide significant performance benefits.

  11. Synthesis and regeneration of lead (IV) acetate

    SciTech Connect (OSTI)

    Boyle, T.J.; Al-Shareef, H.N.; Moore, G.J. [Sandia National Labs., Albuquerque, NM (United States). Advanced Materials Lab.

    1996-11-01T23:59:59.000Z

    Lead acetate [Pb(O{sub 2}CMe){sub 4}] was easily synthesized from a warm solution of Pb{sub 3}O{sub 4}, HO{sub 2}CMe and O(OCMe){sub 2} following literature preparations when the appropriate measures to minimize water contamination were followed. Furthermore, Pb(O{sub 2}CMe){sub 4} which has been decomposed (evidenced by the appearance of a purple color due to oxidation) can be regenerated using a similar preparatory route. Introduction of Pb(O{sub 2}CMe){sub 4} from the two routes outlined above into the IMO process for production of PZT thin films gave films with comparable ferroelectric properties to commercially available Pb(O{sub 2}CMe){sub 4} precursors. However, the freshly synthesized material yields PZT films with better properties compared to the recycled material.

  12. Comparison of leading and next-to-leading logarithmic electroweak corrections to Higgs production

    E-Print Network [OSTI]

    Fabio Siringo

    2013-07-29T23:59:59.000Z

    Using soft-collinear effective theory, the leading-log radiative electroweak corrections are written in a closed and analytical form for the hadronic cross section of Higgs production through vector boson fusion, qq->qqH, one of the most promising channels for studying the Higgs boson at the LHC. The simple leading-log resummation is compared with a full next-to-leading-log calculation, and its accuracy is found to be of order 1% up to 10 TeV, i.e. better than the accuracy of PDFs. Corrections are found to be larger than predicted by one-loop fixed order approximations at LHC energies. The method provides a simple way of incorporating the electroweak corrections in software packages, improving the accuracy of simulations.

  13. Comparison of leading and next-to-leading logarithmic electroweak corrections to Higgs production

    E-Print Network [OSTI]

    Siringo, Fabio

    2013-01-01T23:59:59.000Z

    Using soft-collinear effective theory, the leading-log radiative electroweak corrections are written in a closed and analytical form for the hadronic cross section of Higgs production through vector boson fusion, qq->qqH, one of the most promising channels for studying the Higgs boson at the LHC. The simple leading-log resummation is compared with a full next-to-leading-log calculation, and its accuracy is found to be of order 1% up to 10 TeV, i.e. comparable with the accuracy of PDFs. Corrections are found to be larger than predicted by one-loop fixed order approximations at LHC energies. The method provides a simple way of incorporating the electroweak corrections in software packages, improving the accuracy of simulations.

  14. Development and application of a real time lead-in-air analyzer in controlling lead exposure at a primary lead smelter

    SciTech Connect (OSTI)

    Smith, W.J.; Dekker, D.L.; Greenwood-Smith, R.

    1986-12-01T23:59:59.000Z

    To assist in locating and quantifying fugitive emissions in a primary lead smelter, a real time lead-in-air analyzer has been developed. Dust is collected on paper tape filters and the lead analyzed by X-ray fluorescence. The unit has been used successfully to assist in the implementation of an engineering control monitoring program.

  15. Law Update Cover 2,3 No More Spreading Lead

    E-Print Network [OSTI]

    Hutyra, Lucy R.

    to customers by contractors, of the "Protect Your Family from Lead in Your Home" pamphlet, be- fore beginning because the lead tastes sweet, you need to readjust your thinking. Lead poisoning occurs across allINSIDE Law Update Cover 2,3 No More Spreading Lead Tip of the Month Page 4 Rental Unit Condition

  16. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator Aug 2013 Center for Economic Analysis and Forecasting (CEAF), California

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator Aug 2013 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  17. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2013 Center for Economic Analysis and Forecasting (CEAF), Calif

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2013 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  18. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2010 Institute for Economic and Environmental Studies (IEES), C

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2010 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  19. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2012 Institute for Economic and Environmental Studies (IEES), Califo

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2012 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  20. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2012 Institute for Economic and Environmental Studies (IEES), C

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2012 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  1. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2011 Institute for Economic and Environmental Studies (IEES), Califo

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2011 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  2. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2011 Institute for Economic and Environmental Studies (IEES), C

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2011 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  3. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2014 Center for Economic Analysis and Forecasting (CEAF), California

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2014 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  4. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2012 Institute for Economic and Environmental Studies (IEES), Cal

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2012 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  5. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2011 Institute for Economic and Environmental Studies (IEES), Cal

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2011 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  6. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator February 2014 Center for Economic Analysis and Forecasting (CEAF), Calif

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator February 2014 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  7. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2014 Center for Economic Analysis and Forecasting (CEAF), Califor

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2014 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  8. Lead(ii) Detection An Exceptionally Selective Lead(ii)-Regulatory

    E-Print Network [OSTI]

    He, Chuan

    -spore- forming bacillus that flourishes in millimolar concentrations of toxic heavy metals.[12] It is the only that responds to lead(ii) ions with a high selectivity over other heavy metal ions. This has not been achieved developed for the detection of other small molecules, but with limited success for heavy metal ions

  9. Cool horizons lead to information loss

    E-Print Network [OSTI]

    Borun D. Chowdhury

    2013-07-29T23:59:59.000Z

    There are two evidences for information loss during black hole evaporation: (i) a pure state evolves to a mixed state and (ii) the map from the initial state to final state is non-invertible. Any proposed resolution of the information paradox must address both these issues. The firewall argument focuses only on the first and this leads to order one deviations from the Unruh vacuum for maximally entangled black holes. The nature of the argument does not extend to black holes in pure states. It was shown by Avery, Puhm and the author that requiring the initial state to final state map to be invertible mandates structure at the horizon even for pure states. The proof works if black holes can be formed in generic states and in this paper we show that this is indeed the case. We also demonstrate how models proposed by Susskind, Papadodimas et al. and Maldacena et al. end up making the initial to final state map non-invertible and thus make the horizon "cool" at the cost of unitarity.

  10. Macroencapsulation of lead and steel SWARF

    SciTech Connect (OSTI)

    Zirker, L.; Thiesen, T.; Tyson, D.; Beitel, G.

    1995-12-01T23:59:59.000Z

    The treatability study to macroencapsulate radioactively contaminated lead and steel swarf (cuttings and/or chips)and chunks, a low level mixed waste, from the dismantlement of excess surplus uranium fuel handling and transfer casks was successful. Macroencapsulation is the land disposal restriction treatment standard for this waste form per 40 CFR 268.42 Table 3. An epoxy-based thermoset system was employed due to cracking failures of other types of thermoset systems. Bench scale tests were performed with a two-part epoxy (resin and hardener) using cast iron chips as a surrogate waste media. A two stage encapsulation process was employed in treating the swarf. Two liters of epoxy were added to a 2.8{ell} (3 qt) container of swarf under 51K Pa vacuum (-15-inch of Hg) during the first stage of the process. In this stage each individual particle or chip was wetted by epoxy and allowed to harden into an initial monolith. The second stage encapsulated the initial monolith with a secondary layer of epoxy forming a larger final monolith. By evacuating the air from the swarf and epoxy during the initial monolith encapsulation, a higher density (higher swarf to epoxy ratio) was achieved. Tensile and compressive strength tests were performed on samples and without any media (cast iron chips). The coupons were prepared from a series of monoliths featuring various mixtures ratios and vacuum levels. The tensile strength of epoxy without chips averaged 41M Pa (6000 psi) and 1.4M Pa (2000 psi) with cast iron chips. Compression strengths averaged 140M Pa (20,000 psi) without chips and 66.2M Pa (9600 psi) with cast iron chips.

  11. QCD analysis and effective temperature of direct photons in lead-lead collisions at the LHC

    E-Print Network [OSTI]

    M. Klasen; C. Klein-Bösing; F. König; J. P. Wessels

    2014-09-11T23:59:59.000Z

    We present a systematic theoretical analysis of the ALICE measurement of low-$p_T$ direct-photon production in central lead-lead collisions at the LHC with a centre-of-mass energy of $\\sqrt{s_{NN}}=2.76$ TeV. Using next-to-leading order of perturbative QCD, we compute the relative contributions to prompt-photon production from different initial and final states and the theoretical uncertainties coming from independent variations of the renormalisation and factorisation scales, the nuclear parton densities and the fragmentation functions. Based on different fits to the unsubtracted and prompt-photon subtracted ALICE data, we consistently find an exponential, possibly thermal, photon spectrum from the quark-gluon plasma (or hot medium) with slope $T=304\\pm 58$ MeV and $309\\pm64$ MeV at $p_T\\in[0.8;2.2]$ GeV and $p_T\\in[1.5;3.5]$ GeV as well as a power-law ($p_T^{-4}$) behavior for $p_T>4$ GeV as predicted by QCD hard scattering.

  12. Recent results on electroweak probes in lead-lead and proton-lead collisions from the ATLAS Detector at the LHC

    E-Print Network [OSTI]

    Brooks, William; The ATLAS collaboration

    2015-01-01T23:59:59.000Z

    Photons and weak bosons do not interact strongly with the dense and hot medium formed in nuclear collisions, and thus they should be sensitive to the nuclear modification of parton distribution functions (nPDFs). In particular, proton-lead collisions provide an excellent opportunity to test nPDFs in a less dense environment than lead-lead. The ATLAS detector, optimized for searching new physics in proton-proton collisions, is especially well equipped to measure photons, Z and W bosons in the high occupancy environment produced in heavy ion collisions. Using the full data samples of 2.76 TeV lead-lead and 5.02 TeV proton-lead collisions we will present recent results on the prompt photon, Z and W boson yields as a function of centrality, transverse momentum and rapidity, from the ATLAS experiment. The binary collision scaling of the yields will be discussed in detail.

  13. Solar Decathlon Team Leading the Way Toward Sustainable Living...

    Broader source: Energy.gov (indexed) [DOE]

    Leading the Way Toward Sustainable Living, Even in the Wake of Disasters Solar Decathlon Team Leading the Way Toward Sustainable Living, Even in the Wake of Disasters August 18,...

  14. Anaerobic microbial dissolution of lead and production of organic acids

    DOE Patents [OSTI]

    Francis, A.J.; Dodge, C.; Chendrayan, K.

    1986-02-28T23:59:59.000Z

    The present invention relates to a method of solubilizing lead, in the form of lead oxide, found in industrial wastes, before these wastes are dumped into the environment. The lead is solubilized by dissolving the lead oxide in the wastes through contact with an anaerobic bacterial culture containing the bacterium ATCC No. 53464. The solubilized lead can then be removed from the wastes by chemical separation. It could also be removed by extending the contact period with the bacterial culture. As the culture grows, the solubilized lead is removed from the wastes by bioaccumulation by the microorganism or by immobilization by a polymer-like material produced by the microorganism. At this point, the lead is then removed from the wastes when the waste material is separated from the bacterial culture. If desired, the bacterial culture could be digested at this point to yield relatively pure lead for further industrial use.

  15. COWBOYS OR COMMANDERS: DOES INFORMATION TECHNOLOGY LEAD TO DECENTRALIZATION?

    E-Print Network [OSTI]

    COWBOYS OR COMMANDERS: DOES INFORMATION TECHNOLOGY LEAD TO DECENTRALIZATION? George M. Wyner Thomas) predicted that information technology would lead to the elimination of middle managers and to greater (Eds.), International Conference on Information Systems, Cleveland, International Conference

  16. Lead-Free Surface Finishes for Electronic Components

    E-Print Network [OSTI]

    Lead-Free Surface Finishes for Electronic Components: Tin Whisker Growth METALS This project degraded by the switch to lead- free technology. In particular, the state of compressive stress and the localized creep response (whisker growth) of tin-based lead-free electrodeposits are being measured

  17. FOR MORE INFORMATION, CONTACT: TP Straatsma, Initiative Lead

    E-Print Network [OSTI]

    FOR MORE INFORMATION, CONTACT: TP Straatsma, Initiative Lead 509-375-2802 tps@pnl.gov www.pnl.gov e Development of Exascale Algorithms for Molecular Modeling Lead investigator: Dr. Karol Kowalski Researchers Optimizations for Extreme Scale Systems Lead investigator: Dr. Daniel Chavarria Exascale systems will provide

  18. THE LEAD AND COPPER RULE Anne Sandvig, HDR-EES

    E-Print Network [OSTI]

    Maynard, J. Barry

    THE LEAD AND COPPER RULE Anne Sandvig, HDR-EES 2008 Historical Background The 1986 Safe Drinking districts and was not mandated. In 1991, the USEPA finalized the Lead and Copper Rule (LCR) in response components and by August 1998 manufacturers were required to comply. The Lead and Copper Rule #12;The USEPA

  19. Technical Note Ultrasound Probe with Integrated ECG Lead: Feasibility Study

    E-Print Network [OSTI]

    Smith, Stephen

    Technical Note Ultrasound Probe with Integrated ECG Lead: Feasibility Study ARCHANA RAMIREDDY 27708 stephen.w.smith@duke.edu We integrated electrocardiogram (ECG) leads onto the face of a cardiac of devices needed to col- lect cardiac information. Since the ECG leads were not placed on their standard

  20. Lead contamination around a kindergarten near a battery recycling plant

    SciTech Connect (OSTI)

    Jung-Der Wang; Chang-Sheng Jang; Yaw-Huei Hwang; Zueng-Sang Chen [National Taiwan Univ. (China)

    1992-07-01T23:59:59.000Z

    Lead poisoning has been noticed for more than a thousand years. Increased lead absorption and/or impaired neurobehavioral function among children who lived nearby lead smelters were reported in many different countries. In November of 1987, a worker from a lead battery recycling smelter suffered from anemia and bilateral weakness of his extremities. He was diagnosed as lead poisoning at the National Taiwan University Hospital (NTUH). A subsequent epidemiological survey of the workers from this recycling smelter showed that 31 out of 64 who came for a medical examination suffered from lead poisoning. Since there was a kindergarten next to the factory, we performed this study to determine whether there was an increased lead absorption among children of the exposed kindergarten and its association with the extent of air and soil pollution in the surrounding area. 12 refs., 1 fig., 4 tabs.

  1. On the initial phenomena occurring in lead/lead collisions at relativistic energies

    E-Print Network [OSTI]

    C. Ythier; G. Mouze

    2012-12-18T23:59:59.000Z

    A new study of the initial phenomena occurring in the fireball should confirm the predicted creation of a new state of nuclear matter having a lifetime of 0.17 yoctosecond and releasing an energy of 3.87 GeV. The energy-time uncertainty relation might be connected with an up to now unsuspected momentum-position uncertainty relation holding in a three-dimensional time. This new point of view leads to the interpretation of the charge of a particle as being a rotational motion in time, to a new interpretation of inertia, and to a new interpretation of the color of a particle. The transverse momentum observed in the study of the fireball might be the signature of this motion in time of the charge.

  2. Time-integrated blood lead concentration is a valid surrogate for estimating the cumulative lead dose assessed by tibial lead measurement

    SciTech Connect (OSTI)

    Roels, H.; Konings, J.; Lauwerys, R. [Medical School of the Catholic Univ. of Louvain, Brussels (Belgium)] [and others] [Medical School of the Catholic Univ. of Louvain, Brussels (Belgium); and others

    1995-05-01T23:59:59.000Z

    The concentration of lead in tibia (Pb-T) was measured in vivo by a {sup 109}Cd K-shell X-ray fluorescence technique in 123 workers from a primary lead smelter (age: mean, 45 years; range, 30-61; duration of employment: mean, 20 years; range, 7-45). Their cumulative blood lead index (CBLI) was also calculated on the basis of the blood lead (Pb-B) records available from the company`s medical files. Geometric mean for Pb-T was 49 {mu}g Pb/g bone mineral (range, 15-167). The company`s health surveillance programs, implemented since 1945, resulted in Pb-B values which rarely exceeded 70 {mu}g Pb/dl whole blood. Pb-B at the time of Pb-T measurement averaged 31 {mu}g Pb/dl (range, 6-62) and the geometric mean for CBLI amounted to 803 {mu}g Pb/dl x year (range, 220-2130). Despite various assumptions and uncertainties inherent in the assessment of the cumulative lead dose through Pb-T measurement or CBLI calculation, the relation between both variables in the present lead smelter population is very strong (r{sub pearson}= 0.80, P <0.0001; age explained at the most 9.5% of the variance). The slope of the regression equation of log Pb-T vs log CBLI showed that a doubling of CBLI also corresponds to a doubling of Pb-t. It may be concluded that a sound calculation of CBLI represents a valid surrogate for estimating the life time integrated dose of lead as assessed by the measurement of cortical bone lead (e.g., in tibia). 23 refs., 2 figs., 3 tabs.

  3. ELLIPSOMETRY OF SURFACE LAYERS ON LEAD AND LITHIUM

    E-Print Network [OSTI]

    Peters, Richard Dudley

    2011-01-01T23:59:59.000Z

    Surface Layers on Lead and Lithium By Richard Dudley Peterssulfuric acid and and lithium to water, Acid concentrationsbeen observed in the reaction of lithium with water vapor. i

  4. Sec. Herrington Leads Delegation in Response to Chernobyl Accident...

    National Nuclear Security Administration (NNSA)

    Herrington leads U.S. delegation to Special Session of the International Atomic Energy Agency General Conference in Vienna, Austria, to discuss measures to strengthen...

  5. West Africa Emerges as Leading Region in Africa for Renewable...

    Open Energy Info (EERE)

    West Africa Emerges as Leading Region in Africa for Renewable Energy and Energy Efficiency Home > Groups > Clean and Renewable Energy Dc's picture Submitted by Dc(107) Contributor...

  6. United States Department Of The Navy Geothermal Exploration Leading...

    Open Energy Info (EERE)

    Navy Geothermal Exploration Leading To Shallow And Intermediate-Deep Drilling At Hawthorne Ammunition Depot, Hawthorne, Nv Jump to: navigation, search OpenEI Reference LibraryAdd...

  7. Researchers hope better catalysts lead to better ways of converting...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Researchers hope better catalysts lead to better ways of converting biomass to fuel By Jared Sagoff * August 7, 2013 Tweet EmailPrint ARGONNE, Ill. - Scientists and entrepreneurs...

  8. acid mmaiii leads: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Theses and Dissertations Summary: ??The performance of lead-acid batteries for energy storage in photovoltaicdieselbattery hybrid systems strongly depends on several...

  9. Sandia National Laboratories: Due Diligence on Lead Acid Battery...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the lead acid batteries are processed and recycled legally under a regularly audited New Mexico hazardous waste management permit, Pollution Prevention (P2) was prompted to...

  10. adult mice leads: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    tell parents Internet -While adults worry about unknowns, teens bond and learn social and lead- Computer Technologies and Information Sciences Websites Summary: Kid online? Relax,...

  11. anterior resection leading: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ear, High grade mucoepidermoid carcinoma, Temporal bone resection unknown authors 59 LEAD POISONING PREVENTION INFORMATION Environmental Sciences and Ecology Websites Summary:...

  12. aureus pneumonia leading: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    words, phrases, or symbols indicated by the clue. When you think you Sherriff, Mark S. 92 LEAD POISONING PREVENTION INFORMATION Environmental Sciences and Ecology Websites Summary:...

  13. adrenal medulla leads: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Inga Voges; Friedrich Pahlke; Christoph Dodt; Peter Dominiak; Olaf Jhren 2006-01-01 67 LEAD POISONING PREVENTION INFORMATION Environmental Sciences and Ecology Websites Summary:...

  14. The Global Anthropogenic Lead Experiment Earth, Atmospheric and Planetary Sciences

    E-Print Network [OSTI]

    Einat, Aharonov

    , coal combustion, incineration, cement manufacture). · Leaded gasoline utilization creates fine activities (smelting, coal burning, etc.) · Incineration -------------------------- · "Tin" can solder seams

  15. A leading index of drilling activity: Update and improvements

    SciTech Connect (OSTI)

    Buell, R.S.; Maurer, R.A.

    1986-01-01T23:59:59.000Z

    A five-component composite leading index of United States rotary rig drilling activity is updated. The index is presented for 1949 through April 1986 and is shown to consistently lead turning points in drilling activity. Seven new leading indices based on some new components are also presented. A forecast of drilling activity is made for the remainder of 1986 based on the leading index and the current economic condition of the petroleum industry. The methods used to prepare time series and construct indices are reviewed.

  16. Automated portable analyzer for lead(II) based on sequential...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    flow technique which required minimal volume of samples and reagents and allowed the automation of the analyzer operation. The portable analyzer was evaluated for lead (Pb)...

  17. Energy Data Management Lead-by-Example Resources

    Broader source: Energy.gov [DOE]

    State and local governments can lead by example by promoting energy efficiency programs and policies for public facilities, equipment, and government operations.

  18. NERSC Leads Next-Generation Code Optimization Effort

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Leads Next-Generation Code Optimization Effort NERSC Launches Next-Generation Code Optimization Effort NERSC, Intel, Cray team up to prepare users for transition to exascale...

  19. Paul Langan to lead ORNL's Neutron Sciences Directorate | ornl...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    science activities, which include two leading DOE Office of Science user facilities for neutron scattering analysis: The Spallation Neutron Source (SNS) and the High Flux Isotope...

  20. AVTA: 2010 Honda Civic HEV with Experimental Ultra Lead Acid...

    Broader source: Energy.gov (indexed) [DOE]

    and development. The following reports describe results of testing done on a 2010 Civic hybrid electric vehicle with an advanced experimental ultra-lead acid battery, an...

  1. An Insoluble Titanium-Lead Anode for Sulfate Electrolytes

    SciTech Connect (OSTI)

    Ferdman, Alla

    2005-05-11T23:59:59.000Z

    The project is devoted to the development of novel insoluble anodes for copper electrowinning and electrolytic manganese dioxide (EMD) production. The anodes are made of titanium-lead composite material produced by techniques of powder metallurgy, compaction of titanium powder, sintering and subsequent lead infiltration. The titanium-lead anode combines beneficial electrochemical behavior of a lead anode with high mechanical properties and corrosion resistance of a titanium anode. In the titanium-lead anode, the titanium stabilizes the lead, preventing it from spalling, and the lead sheathes the titanium, protecting it from passivation. Interconnections between manufacturing process, structure, composition and properties of the titanium-lead composite material were investigated. The material containing 20-30 vol.% of lead had optimal combination of mechanical and electrochemical properties. Optimal process parameters to manufacture the anodes were identified. Prototypes having optimized composition and structure were produced for testing in operating conditions of copper electrowinning and EMD production. Bench-scale, mini-pilot scale and pilot scale tests were performed. The test anodes were of both a plate design and a flow-through cylindrical design. The cylindrical anodes were composed of cylinders containing titanium inner rods and fitting over titanium-lead bushings. The cylindrical design allows the electrolyte to flow through the anode, which enhances diffusion of the electrolyte reactants. The cylindrical anodes demonstrate higher mass transport capabilities and increased electrical efficiency compared to the plate anodes. Copper electrowinning represents the primary target market for the titanium-lead anode. A full-size cylindrical anode performance in copper electrowinning conditions was monitored over a year. The test anode to cathode voltage was stable in the 1.8 to 2.0 volt range. Copper cathode morphology was very smooth and uniform. There was no measurable anode weight loss during this time period. Quantitative chemical analysis of the anode surface showed that the lead content after testing remained at its initial level. No lead dissolution or transfer from the anode to the product occurred.A key benefit of the titanium-lead anode design is that cobalt additions to copper electrolyte should be eliminated. Cobalt is added to the electrolyte to help stabilize the lead oxide surface of conventional lead anodes. The presence of the titanium intimately mixed with the lead should eliminate the need for cobalt stabilization of the lead surface. The anode should last twice as long as the conventional lead anode. Energy savings should be achieved due to minimizing and stabilizing the anode-cathode distance in the electrowinning cells. The anode is easily substitutable into existing tankhouses without a rectifier change.The copper electrowinning test data indicate that the titanium-lead anode is a good candidate for further testing as a possible replacement for a conventional lead anode. A key consideration is the cost. Titanium costs have increased. One of the ways to get the anode cost down is manufacturing the anodes with fewer cylinders. Additional prototypes having different number of cylinders were constructed for a long-term commercial testing in a circuit without cobalt. The objective of the testing is to evaluate the need for cobalt, investigate the effect of decreasing the number of cylinders on the anode performance, and to optimize further the anode design in order to meet the operating requirements, minimize the voltage, maximize the life of the anode, and to balance this against a reasonable cost for the anode. It is anticipated that after testing of the additional prototypes, a whole cell commercial test will be conducted to complete evaluation of the titanium-lead anode costs/benefits.

  2. Geochemical study of lead in soils from West Dallas, Texas

    SciTech Connect (OSTI)

    Ibrahim, N.M.; Carter, J.L. (Univ. of Texas, Dallas, TX (United States). Programs in Geosciences)

    1993-02-01T23:59:59.000Z

    Soil samples from West Dallas near the RSR smelter were collected and tested to see the content, source, and mobility of lead. 30 cm and 90 cm long cores were cut into 1 cm long pieces and each piece analyzed separately. The results showed that 90%--95% of the lead is readily extractable in cold dilute nitric acid. The lateral distribution of lead in West Dallas indicates an exponential-like decrease with distance from the RSR smelter. Concentrations greater than 500 ppm occur in soils below 10 cm within 1,000 feet of the smelter. In the vicinity of the smelter (300 feet radius), soil cores with total lead content as high as 18,000 ppm in the top 15 cm were obtained. At a distance of 2,400 feet of the smelter the lead in the soil amounts to 400 ppm and drops to 270 ppm at 4,000 feet. The total lead content with depth, correlates with previous clean-up and civil activities in the area: (1) where the soil is original, the lead concentration decreases exponentially with depth; (2) where the soil was cleaned up, the top 10 cm are devoid of lead but are underlain by soil whose lead content varies in response to distance from the smelter; (3) where the top soil had been disturbed (removed, replaced, mixed, etc.) as a result of civil works, the lead content is relatively lower than 1 (above). The underlying insitu soils exhibit similar lead concentration as those in 2 (above).

  3. Know Stroke Stroke is the third leading cause of

    E-Print Network [OSTI]

    Bandettini, Peter A.

    #12;Know Stroke Stroke is the third leading cause of death in the United States and a leading cause of serious, long-term disability in adults. About 600,000 new strokes are reported in the U.S. each year. The good news is that treatments are available that can greatly reduce the damage caused by a stroke

  4. Biosorption of Lead and Nickel by Biomass of Marine Algae

    E-Print Network [OSTI]

    Volesky, Bohumil

    Biosorption of Lead and Nickel by Biomass of Marine Algae Z.R. Holan and B. Volesky" Department 22, 1993 Screening tests of different marine algae biomass types revealed a high passive biosorptive uptake of lead up to 270 mg Pb/g of biomass in some brown marine algae. Members of the order Fucales

  5. Following Germany's Lead: Using International Monetary Linkages to Estimate

    E-Print Network [OSTI]

    Sadoulet, Elisabeth

    Following Germany's Lead: Using International Monetary Linkages to Estimate the Effect of Monetary to countries with the weakest economic ties to Germany. We thank participants at the 2004 NBER Summer Workshop (2001). 2 Many European countries followed Germany's lead in setting their monetary policy during our

  6. A Study of Lead Ingot Cargoes from Ancient Mediterranean Shipwrecks

    E-Print Network [OSTI]

    Brown, Heather Gail

    2011-10-21T23:59:59.000Z

    Lead is often relegated to a footnote or sidebar in the study of ancient metals. However, the hundreds of lead ingots discovered in underwater sites over the past half-century have attested to the widespread production and trade of this utilitarian...

  7. FINAL LEAD COMMISSIONER REPORT 2012 INTEGRATED ENERGY POLICY

    E-Print Network [OSTI]

    FINAL LEAD COMMISSIONER REPORT 2012 INTEGRATED ENERGY POLICY REPORT UPDATE CALIFORNIA COMMISSION Carla J. Peterman Lead Commissioner, Integrated Energy Policy Report Robert P. Oglesby Executive was prepared under the 2012 Integrated Energy Policy Report proceeding, Docket #12-IEP-1A. The final report

  8. assassination bullet lead: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    assassination bullet lead First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 August 2014 Lead isotopes and...

  9. Partially Extracted Defibrillator Coils and Pacing Leads Alter Defibrillation Thresholds

    E-Print Network [OSTI]

    Utah, University of

    effect on DFTs. Introduction: Sudden cardiac death is the leading cause of death in the United States with 325,000 deaths per year. This translates to 1,000 deaths per day or 1 death every two minutes.1 USA Summary: Abandoned ICD coils and pacing leads provide a conductor substrate for electric field

  10. Method for fabricating fan-fold shielded electrical leads

    DOE Patents [OSTI]

    Rohatgi, R.R.; Cowan, T.E.

    1994-12-27T23:59:59.000Z

    Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figures.

  11. Method for fabricating fan-fold shielded electrical leads

    DOE Patents [OSTI]

    Rohatgi, Rajeev R. (Mountain View, CA); Cowan, Thomas E. (Livermore, CA)

    1994-01-01T23:59:59.000Z

    Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate.

  12. Development of lead-free solders for hybrid microcircuits

    SciTech Connect (OSTI)

    Hosking, F.M.; Vianco, P.T.; Frear, D.R.; Robinson, D.G.

    1996-01-01T23:59:59.000Z

    Extensive work has been conducted by industry to develop lead-free solders for electronics applications. The driving force behind this effort is pressure to ban or tax the use of lead-bearing solders. There has been further interest to reduce the use of hazardous chemical cleaners. Lead-free soldering and low-residue, ``no clean`` assembly processing are being considered as solutions to these environmental issues. Most of the work has been directed toward commercial and military printed wiring board (PWB) technology, although similar problems confront the hybrid microcircuit (HMC) industry, where the development of lead-free HMC solders is generally lagging. Sandia National Laboratories is responsible for designing a variety of critical, high reliability hybrid components for radars. Sandia has consequently initiated a project, as part of its Environmentally Conscious Manufacturing program, to develop low-residue, lead-free soldering for HMCs. This paper discusses the progress of that work.

  13. Effect of the {delta}-aminolevulinate dehydratase polymorphism on the accumulation of lead in bone and blood in lead smelter workers

    SciTech Connect (OSTI)

    Fleming, D.E.B.; Chettle, D.R. [McMaster Univ., Hamilton, Ontario (Canada). Dept. of Physics and Astronomy] [McMaster Univ., Hamilton, Ontario (Canada). Dept. of Physics and Astronomy; Wetmur, J.G.; Desnick, R.J. [Mount Sinai School of Medicine, New York, NY (United States)] [Mount Sinai School of Medicine, New York, NY (United States); Robin, J.P. [Noranda Inc., Montreal, Quebec (Canada)] [Noranda Inc., Montreal, Quebec (Canada); Boulay, D.; Richard, N.S. [Brunswick Mining and Smelting Corp. Ltd., Belledune, New Brunswick (Canada). Occupational Health Services] [Brunswick Mining and Smelting Corp. Ltd., Belledune, New Brunswick (Canada). Occupational Health Services; Gordon, C.L.; Webber, C.E. [Hamilton Health Sciences Corp., Hamilton, Ontario (Canada). Dept. of Nuclear Medicine] [Hamilton Health Sciences Corp., Hamilton, Ontario (Canada). Dept. of Nuclear Medicine

    1998-04-01T23:59:59.000Z

    Lead inhibition of the zinc metalloenzyme {delta}-aminolevulinate dehydratase (ALAD) is one of the most sensitive indicators of blood lead levels. Whole blood lead, serum lead, and ALAD genotype were determined for 381 lead smelter workers, including 70 workers expressing the ALAD allele, whose blood lead elevations were observed for more than 20 years of employment. The same employees demonstrated higher serum lead levels. Using a cumulative blood lead index (CBLI) for each worker, based on individual blood lead histories, and in vivo X-ray fluorescence measurements of bone lead to estimate total lead body burden, the slopes of linear relations of bone lead to CBLI were greater for workers homoallelic for ALAD, indicating more efficient uptake of lead from blood into bone. This effect was most significant in calcaneus bone and for workers hired since 1977. Decreased transfer of blood lead into bone in individuals expressing the ALAD allele contrasted with increased blood lead.

  14. Anaerobic microbial dissolution of lead and production of organic acids

    DOE Patents [OSTI]

    Francis, Arokiasamy J. (Middle Island, NY); Dodge, Cleveland (Wading River, NY); Chendrayan, Krishnachetty (Coimbatore Tamil Nadu, IN); Quinby, Helen L. (Cambridge, MD)

    1988-01-01T23:59:59.000Z

    The present invention relates to an anaerobic bacterial culture of Clostridium sp. ATCC No. 53464 which solubilizes lead oxide under anaerobic conditions in coal and industrial wastes and therefore presents a method of removing lead from such wastes before they are dumped into the environment. The rate of lead dissolution during logarithmic growth of the bacteria in 40 ml medium containing 3.32 .mu.moles of lead as lead oxide was 0.042 .mu.moles ml.sup.-1 hr.sup.-1. Dissolution of lead oxide by the bacterial isolate is due to the production of metabolites and acidity in the culture medium. The major metabolites are acetic, butyric and lactic acid. Clostridium sp. ATCC No. 53464 can be used in the recovery of strategic metals from ores and wastes and also for the production of lactic acid for commercial purposes. The process yields large quantities of lactic acid as well as lead complexed in a stable form with said acids.

  15. Anaerobic microbial dissolution of lead and production of organic acids

    DOE Patents [OSTI]

    Francis, A.J.; Dodge, C.; Chendrayan, K.; Quinby, H.L.

    1987-04-16T23:59:59.000Z

    The present invention related to an anaerobic bacterial culture of Clostridium sp. ATCC No. 53464 which solubilizes lead oxide under anaerobic conditions in coal and industrial wastes and therefore presents a method of removing lead from such wastes before they are dumped into the environment. The rat of lead dissolution during logarithmic growth of the bacteria in 40 ml medium containing 3.32 ..mu..moles of lead as lead oxide was 0.042 ..mu..moles m1/sup /-/1/ hr/sup /-/1/. Dissolution of lead oxide by the bacterial isolate is due to the production of metabolites and acidity in the culture medium. The major metabolites are acetic, butyric and lactic acid. The major metabolites are acetic, butyric and lactic acid. Clostridium sp. ATCC No. 53464 can be used in the recovery of the strategic metals from ores and wastes and also for the production of lactic acid for commercial purposes. The process yields large quantities of lactic acid as well as lead complexed in a stable form with said acids. 4 figs., 3 tabs.

  16. Pilot study dismantlement of 20 lead-lined shipping casks

    SciTech Connect (OSTI)

    Thurmond, S.M.

    1995-08-01T23:59:59.000Z

    This report describes a pilot study conducted at the INEL to dismantle lead-lined casks and shielding devices, separate the radiologically contaminated and hazardous materials, and recycle resultant scrap lead. The facility areas where the work was performed, dismantlement methods, and process equipment are described. Issues and results associated with recycling the lead as a free-released scrap metal are presented and discussed. Data and results from the pilot study are summarized and presented. The study concluded that cask dismantlement at the INEL can be performed as a legitimate recycling activity for scrap lead. Ninety-one percent of the lead recovered passed free-release criteria. The value of the 50,375 lb of recovered lead is approximately $0.45/lb. Resultant waste streams can be satisfactorily treated and disposed. Only very low levels of bulk radiological contamination (47 picocuries/gram of 137 Cs and 3.2 picocuries/gram of {sup 6O}Co) were detected in the lead rejected for free release.

  17. Blood lead levels and remediation of an abandoned smelter site

    SciTech Connect (OSTI)

    Eidson, M. [New Mexico Dept. of Health, Santa Fe, NM (United States). Div. of Epidemiology, Evaluation, and Planning; Tollestrup, K. [Univ. of New Mexico School of Medicine, Albuquerque, NM (United States). Family and Community Medicine Dept.

    1995-05-01T23:59:59.000Z

    Elevated soil lead levels were documented in a New Mexico community, with levels up to 24,800 ppm in a smelter slag pile, 20 or more feet from residences. The New Mexico Department of Health offered blood lead screening to residents of three geographic areas before and after an emergency cleanup by the US Environmental Protection Agency. Blood lead levels prior to the cleanup ranged from undetectable (< 5 {mu}g/dl) to 29 {mu}g/dl; after the cleanup, they ranged from undetectable to 10 {mu}g/dl. Significant reductions in mean blood lead levels after the cleanup were found for all three geographic areas: from 6.67 {mu}g/dl to 4 {mu}dl (smelter area), from 4.12 {mu}g/dl to 2.5 {mu}g/dl (town area), and from 5.5 {mu}g/dl to 2.5 {mu}g/dl (northeast area). In both years, the mean blood lead levels of individuals who lived near the smelter area were significantly higher than the levels for those living in town for those participating in both years of the study. Mean blood lead levels were significantly higher for smelter area participants who had a household member working at a lead battery plant (19.4 {mu}g/dl) compared to those residents who did not (5.83 {mu}g/dl).

  18. Performance of the MFTF magnet cryogenic power leads

    SciTech Connect (OSTI)

    VanSant, J.H.

    1983-11-30T23:59:59.000Z

    The cryogenic power lead system for the MFTF superconducting magnets has been acceptance tested and operated with the magnets. This system, which includes 5-m-long superconducting buses, 1.5-m-long vapor-cooled transition leads, external warm buses, and a cryostack, can conduct up to 6000 A (dc) and operate adiabatically for long periods. We present both design details and performance data; our MFTF version is an example of a reliable lead system for large superconducting magnets contained in a much larger vacuum vessel.

  19. Surface dust wipes are the best predictors of blood leads in young children with elevated blood lead levels

    SciTech Connect (OSTI)

    Gulson, Brian, E-mail: brian.gulson@mq.edu.au [Graduate School of the Environment, Macquarie University, North Ryde NSW 2109 (Australia) [Graduate School of the Environment, Macquarie University, North Ryde NSW 2109 (Australia); CSIRO Earth Science and Resource Engineering, North Ryde NSW 2113 (Australia); Anderson, Phil [Information and Statistics Group, Australian Institute of Health and Welfare, Canberra ACT 2601 (Australia) [Information and Statistics Group, Australian Institute of Health and Welfare, Canberra ACT 2601 (Australia); Faculty of Health, University of Canberra, Canberra ACT 2601 (Australia); Taylor, Alan [Department of Psychology, Macquarie University, Sydney NSW 2109 (Australia)] [Department of Psychology, Macquarie University, Sydney NSW 2109 (Australia)

    2013-10-15T23:59:59.000Z

    Background: As part of the only national survey of lead in Australian children, which was undertaken in 1996, lead isotopic and lead concentration measurements were obtained from children from 24 dwellings whose blood lead levels were ?15 µg/dL in an attempt to determine the source(s) of their elevated blood lead. Comparisons were made with data for six children with lower blood lead levels (<10 µg/dL). Methods: Thermal ionisation and isotope dilution mass spectrometry were used to determine high precision lead isotopic ratios ({sup 208}Pb/{sup 206}Pb, {sup 207}Pb/{sup 206}Pb and {sup 206}Pb/{sup 204}Pb) and lead concentrations in blood, dust from floor wipes, soil, drinking water and paint (where available). Evaluation of associations between blood and the environmental samples was based on the analysis of individual cases, and Pearson correlations and multiple regression analyses based on the whole dataset. Results and discussion: The correlations showed an association for isotopic ratios in blood and wipes (r=0.52, 95% CI 0.19–0.74), blood and soil (r=0.33, 95% CI ?0.05–0.62), and blood and paint (r=0.56, 95% CI 0.09–0.83). The regression analyses indicated that the only statistically significant relationship for blood isotopic ratios was with dust wipes (B=0.65, 95% CI 0.35–0.95); there were no significant associations for lead concentrations in blood and environmental samples. There is a strong isotopic correlation of soils and house dust (r=0.53, 95% CI 0.20–0.75) indicative of a common source(s) for lead in soil and house dust. In contrast, as with the regression analyses, no such association is present for bulk lead concentrations (r=?0.003, 95% CI ?0.37–0.36), the most common approach employed in source investigations. In evaluation of the isotopic results on a case by case basis, the strongest associations were for dust wipes and blood. -- Highlights: • Children with elevated blood lead ?15 µg/dL compared with a group with <10 µg/dL. • High precision lead isotopic ratios in blood, house dust wipes, soil, water, paint. • Associations for isotopic measures of blood and dust, blood and soil, blood and paint. • Regressions gave significance for isotopic measures of blood/dust and dust/soil.

  20. Determinants of elevated blood lead during pregnancy in a population surrounding a lead smelter in Kosovo, Yugoslavia

    SciTech Connect (OSTI)

    Graziano, J.H.; Factor-Litvak, P.; Murphy, M.J.; Zhao, Yuhua; Lolacono, N.J. (Columbia Univ., New York, NY (USA)); Popovac, D.; Ahmedi, X.; Zvicer, Z.; Nenezic, D.U. (Univ of Pristina Medical School (Yugoslavia)); Shrout, P.; Kline, J.; Stein, Z. (Columbia Univ., New York, NY (USA) New York State Psychiatric Institute, New York (USA)); Mehmeti, A.; Rajovic, B. (Medicinski Centar, Titova Mitrovica (Yugoslavia))

    1990-11-01T23:59:59.000Z

    The authors are prospectively examining the relation between environmental lead exposure and pregnancy outcome in cohorts of women exposed to a wide range of air lead concentrations. Titova Mitrovica, Yugoslavia, is the site of a large lead smelter, refinery, and battery factory. At midpregnancy, 602 women in T. Mitrovica and 900 women in Pristina, a non-lead-exposed control town, were interviewed. Blood was obtained for blood lead (PbB), hemoglobin erythrocyte protoporphyrin, and serum ferritin measurements. Women were seen again at delivery, at which time maternal and umbilical cord blood samples were obtained. While many demographic and social characteristics were similar across the two towns, women in Pristina were more likely to report employment outside the home, cigarette smoking, and alcohol use during pregnancy. As expected, PbB levels were substantially higher in the smelter town. Within T. Mitrovica, distance between the home and the smelter was the most important predictor of PbB at mid-pregnancy and delivery. Husband's employment in the lead industry was associated with a significant increase in maternal PbB levels independent of place of residence. Overall, the placenta was a poor barrier to lead; the relationship between maternal PbB and umbilical cord PbB was linear across a wide range of PbB levels.

  1. Robert C. Seamans, Jr. Appointed to Lead Nuclear Weapons Program...

    National Nuclear Security Administration (NNSA)

    Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at NNSA Blog Home About Us Our History NNSA Timeline Robert C. Seamans, Jr. Appointed to Lead ... Robert C. Seamans,...

  2. The impact of lead time on truckload transportation rates

    E-Print Network [OSTI]

    Caldwell, Erik R. (Erik Russell)

    2008-01-01T23:59:59.000Z

    The objective of this thesis was to analyze truckload shipment transactions in order to determine if rates are impacted by tender lead time, which is the amount of time between when a carrier is offered a load to when the ...

  3. Development of alternatives to lead-bearing solders

    SciTech Connect (OSTI)

    Vianco, P.T. [Sandia National Labs., Albuquerque, NM (United States)

    1993-07-01T23:59:59.000Z

    Soldering technology, using tin-lead alloys has had a significant role in the packaging of highly functional, low cost electronic devices. The elimination of lead from all manufactured products, whether through legislation or tax incentives, will impact the electronics community which uses lead-containing solders. In response to these proposed measures, the National Center for Manufacturing Sciences has established a multi-year program involving participants from industry, academia, and the national laboratories with the objective to identify potential replacements for lead-bearing solders. Selection of candidate alloys is based upon the analysis of materials properties, manufacturability, modeling codes for reliability prediction, as well as toxicological properties and resource availability, data developed in the program.

  4. antioxidant enzymes leading: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Boyd, R N; Reitzner, S D; Vogel, P 2003-01-01 360 AUV Commercialization - Who's Leading the Pack? CiteSeer Summary: Taking AUV technology from the drawing board and putting...

  5. Leading change management projects in international cross-cultural settings

    E-Print Network [OSTI]

    Repoux, Charles

    2014-01-01T23:59:59.000Z

    In an increasingly complex world for Multinational Companies, it is difficult for managers to keep a firm grasp over the global projects they are tasked to implement. Many of them lead teams operating across country borders, ...

  6. Characterization of lead-recycling facility emissions at various workplaces

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    studies on lead smelter emissions deal with the environmental impact of outdoor particles, but only a few and then compared; namely Furnace and Refining PM respectively present in the smelter and at refinery workplaces

  7. Microfluidic devices and Block Copolymer Nanolithography Lead: D. Angelescu

    E-Print Network [OSTI]

    Baudoin, Geneviève

    Microfluidic devices and Block Copolymer Nanolithography Lead: D. Angelescu Permanent members: B, X. Yuan One of our activities in microfluidics involves the design of a microfluidic system which measures pressure drops along microfluidic channels involving different types of constrictions using

  8. Leading Edge Spinning the Web of Cell Fate

    E-Print Network [OSTI]

    Corces, Victor G.

    Leading Edge Minireview Spinning the Web of Cell Fate Kevin Van Bortle1 and Victor G. Corces1,* 1 involved in spinning the web of cell fate. Chromatin at the Nuclear Lamina The nuclear lamina is a thin

  9. Experimental validation of lead cross sections for scale and MCNP

    SciTech Connect (OSTI)

    Henrikson, D.J.

    1995-12-01T23:59:59.000Z

    Moving spent nuclear fuel between facilities often requires the use of lead-shielded casks. Criticality safety that is based upon calculations requires experimental validation of the fuel matrix and lead cross section libraries. A series of critical experiments using a high-enriched uranium-aluminum fuel element with a variety of reflectors, including lead, has been identified. Twenty-one configurations were evaluated in this study. The fuel element was modelled for KENO V.a and MCNP 4a using various cross section sets. The experiments addressed in this report can be used to validate lead-reflected calculations. Factors influencing calculated k{sub eff} which require further study include diameters of styrofoam inserts and homogenization.

  10. Lead Groundwater Contamination of Groundwater in the Northeast ...

    E-Print Network [OSTI]

    2001-03-12T23:59:59.000Z

    The detailed description of the migration of pollutants is fundamental for the groundwater monitoring and it ... historical data with a, groundwater contamination sampling for water quality analyses ... can be toxic to living organisms. Lead can ...

  11. The effects of part commonality on product development lead time

    E-Print Network [OSTI]

    Svensson, Nicholas, 1965-

    2005-01-01T23:59:59.000Z

    Nortel Networks, a leading global supplier of telecommunications equipment, is engaged in an increasingly competitive global market place. Within this market, Nortel Networks is positioning itself as the leader of global ...

  12. antigen levels leading: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    20 21 22 23 24 25 Next Page Last Page Topic Index 1 Photodynamic Therapy of Tumors Can Lead to Development of Systemic Antigen-Specific Immune Response MIT - DSpace Summary: The...

  13. ancient greek lead: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: , as it may lead to the physical replication of the object by means of 3D printing 6. This has become clearqp: A Tool for Generating 3D Models of Ancient Greek...

  14. antileishmanial lead drug: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Websites Summary: AND ADDICTION (K12) Funding Opportunity Number: PAR-10-177. CFDA Number(s): 93.279. AgencyDepartment: National) leading to research independence in the...

  15. Direct printing of lead zirconate titanate thin films

    E-Print Network [OSTI]

    Bathurst, Stephen, 1980-

    2008-01-01T23:59:59.000Z

    Thus far, use of lead zirconate titanate (PZT) in MEMS has been limited due to the lack of process compatibility with existing MEMS manufacturing techniques. Direct printing of thin films eliminates the need for photolithographic ...

  16. MERCURY AND LEAD SAMPLING AT MINNESOTA POWER'S BOSWELL ENERGY CENTER

    SciTech Connect (OSTI)

    Dennis L. Laudal

    2000-08-01T23:59:59.000Z

    At the request of the Minnesota Power, Inc., the Energy & Environmental Research Center (EERC) sampled for lead at the stack (or duct directly leading to the stack) for three units at the Boswell Energy Center. All sampling was done in triplicate using U.S. Environmental Protection Agency (EPA) Method 12, with sampling procedures following EPA Methods 1 through 4. During the test program, lead sampling was done using EPA Method 12 in the duct at the outlet of the baghouse serving Unit 2 and the duct at the outlet of the wet particulate scrubber serving Unit 3. For Unit 4, lead sampling was done at the stack. The specific objective for the project was to determine the concentration of lead in the flue gas being emitted into the atmosphere from the Boswell Energy Center. The test program was performed during the period of May 8 through 11, 2000. This report presents the test data, sample calculations, and results, and a discussion of the lead sampling performed at the Boswell Energy Center. The detailed test data and test results, raw test data, process data, laboratory reports, and equipment calibration records are provided in Appendices A, B, and C.

  17. The design of a functionally graded composite for service in high temperature lead and lead-bismuth cooled nuclear reactors

    E-Print Network [OSTI]

    Short, Michael Philip

    2010-01-01T23:59:59.000Z

    A material that resists lead-bismuth eutectic (LBE) attack and retains its strength at 700°C would be an enabling technology for LBE-cooled reactors. No single alloy currently exists that can economically meet the required ...

  18. The use of NTA and EDTA for lead phytoextraction from soil from a battery recycling site

    E-Print Network [OSTI]

    Freitas, Eriberto; Nascimento, Clistenes; Silva, Airon

    2009-01-01T23:59:59.000Z

    are lead mining, lead smelting and battery recycling.Areas near Pb recycling facilities may be enriched bysoil with lead. A battery recycling site is a location where

  19. Childhood lead poisoning from the smelter in Torreon, Mexico

    SciTech Connect (OSTI)

    Soto-Jimenez, Martin F., E-mail: martin@ola.icmyl.unam.mx [Unidad Academica Mazatlan, Instituto de Ciencias del Mar y Limnologia, Universidad Nacional Autonoma de Mexico (UAM-ICMyL-UNAM), Apdo. Postal 811, Mazatlan 82040, Sinaloa (Mexico); Flegal, Arthur R. [WIGS, Microbiology and Environmental Toxicology, University of California at Santa Cruz, Santa Cruz, CA 95064 (United States)] [WIGS, Microbiology and Environmental Toxicology, University of California at Santa Cruz, Santa Cruz, CA 95064 (United States)

    2011-05-15T23:59:59.000Z

    Lead concentrations and isotopic compositions in blood samples of 34 children (ages 2-17 years) living within a 113 km{sup 2} area of a silver-zinc-lead smelter plant in Torreon, Mexico were compared to those of associated environmental samples (soil, aerosols, and outdoor and indoor dust) to identify the principal source(s) of environmental and human lead contamination in the area. Lead concentrations of soil and outdoor dust ranged 130-12,050 and 150-14,365 {mu}g g{sup -1}, respectively. Concentrations were greatest near the smelter, with the highest levels corresponding with the prevailing wind direction, and orders of magnitude above background concentrations of 7.3-33.3 {mu}g g{sup -1}. Atmospheric lead depositions in the city varied between 130 and 1350 {mu}g m{sup -2} d{sup -1}, again with highest rates <1 km from the smelter. Blood lead (PbB) concentrations (11.0{+-}5.3 {mu}g dl{sup -1}) levels in the children ranged 5.0-25.8 {mu}g dl{sup -1}, which is 3-14 times higher than the current average (1.9 {mu}g dl{sup -1}) of children (ages 1-5 years) in the US. Lead isotopic ratios ({sup 206}Pb/{sup 207}Pb, {sup 208}Pb/{sup 207}Pb) of the urban dust and soil (1.200{+-}0.009, 2.467{+-}0.003), aerosols (1.200{+-}0.002, 2.466{+-}0.002), and PbB (1.199{+-}0.001, 2.468{+-}0.002) were indistinguishable from each other, as well as those of the lead ores processed at the smelter (1.199{+-}0.007, 2.473{+-}0.007). Consequently, an elevated PbB concentrations of the children in Torreon, as well as in their environment, are still dominated by industrial emissions from the smelter located within the city, in spite of new controls on atmospheric releases from the facility. - Highlights: {yields} Pb contents in environmental samples evidenced chronic Pb pollution in Torreon. {yields} Pb stable isotopes evidenced contemporary emissions from the Ag-Cod-Pb-Zn smelter. {yields} Pb urban dust and soil account for most of the childhood lead poisoning in Torreon.{yields} Levels of Pub in Torreon's children are 3-14 times higher than children in the US.{yields} Children Pub concentrations are primarily attributed to emissions from the smelter.

  20. NOT EVERY HYBRID BECOMES ANOT EVERY HYBRID BECOMES A PRIUS: THE CASE AGAINST THEPRIUS: THE CASE AGAINST THE

    E-Print Network [OSTI]

    for the expansion of nuclear energyof nuclear energy ·· Waste ManagementWaste Management ·· Fuel Resource Management ITS HYBRID CAR CALLED THE NUCLEON WITH NUCLEAR DRIVECALLED THE NUCLEON WITH NUCLEAR DRIVE #12;Past''s potential fors potential for nuclear applicationsnuclear applications The hybrid blanket must also breed

  1. ATOC 3500/CHEM 3151 Spring 2014 Which is more fuel efficient, a Mercedes E250 or a Prius?

    E-Print Network [OSTI]

    Toohey, Darin W.

    . However, there is still a catch...most regular gasoline contains 10% ethanol in order to further reduce pollutants like carbon monoxide. We really need to account for the even lighter weight of 90%/10% gasoline/ethanol done with such a blend). But it's easiest to just do the last calculation. A 90/10 mixture of gasoline/ethanol

  2. Primary lead smelter, Doe Run, Herculaneum, Missouri (kit)

    SciTech Connect (OSTI)

    NONE

    1999-08-01T23:59:59.000Z

    The United States Environmental Protection Agency`s (EPA) Emission Standards Division (ESD) is investigating the primary lead smelting source category to identify and quantify organic hazardous air pollutants (HAPs) emitted from blast furnaces. The primary objective was to obtain data on the emissions of volatile and semi-volatile organic HAPs, aldehydes, and ketones from primary lead smelter blast furnaces. A secondary objective was to obtain data on the emissions of carbon monoxide. The data will be used by ESD to determine whether organic HAPs are emitted at levels that would justify regulation under the Maximum Achievable Control Technology (MACT) program. The Doe Run Company, which operates a primary lead smelter in Herculaneum, Missouri was selected by the ESD as the host facility for this project.

  3. Critical magnetic field of surface superconductivity in lead

    SciTech Connect (OSTI)

    Khlyustikov, I. N., E-mail: khly@kapitza.ras.ru [Russian Academy of Sciences, Kapitza Institute of Physical Problems (Russian Federation)

    2011-12-15T23:59:59.000Z

    The critical superconductivity field H{sub c3} is measured on lead single crystals. It is shown that the temperature dependence of H{sub c3}/H{sub c} in the vicinity of superconducting transition temperature T{sub c} is essentially nonlinear. Relative changes in the value of H{sub c3}/H{sub c} reach approximately 30%, which cannot be described by the Ginzburg-Landau theory. The experimental temperature dependences lead to the conclusion that the surface superconducting transition temperature noticeably exceeds the superconducting transition temperature in the bulk of the semiconductor. The differences in the critical temperatures and in the Ginzburg-Landau parameters for lead are estimated.

  4. Isotopic generator for bismuth-212 and lead-212 from radium

    DOE Patents [OSTI]

    Atcher, Robert W. (Kensington, MD); Friedman, Arnold M. (Park Forest, IL); Hines, John (Glen Ellyn, IL)

    1987-01-01T23:59:59.000Z

    A method and apparatus for providing radionuclides of bismuth-212 and lead-212. Thorium-228 and carrier solution starting material is input to a radiologically contained portion of an isotopic generator system, and radium-224 is separated from thorium-228 which is retained by a strongly basic anion exchange column. The separated radium-224 is transferred to an accessible, strongly acidic cationic exchange column. The cationic column retains the radium-224, and natural radioactive decay generates bismuth-212 and lead-212. The cationic exchange column can also be separated from the contained portion of the system and utilized without the extraordinary safety measures necessary in the contained portion. Furthermore, the cationic exchange column provides over a relatively long time period the short lived lead-212 and bismuth-212 radionuclides which are useful for a variety of medical therapies.

  5. CORROSION OF LEAD SHIELDING IN NUCLEAR MATERIALS PACKAGES

    SciTech Connect (OSTI)

    Subramanian, K; Kerry Dunn, K; Joseph Murphy, J

    2008-07-18T23:59:59.000Z

    Inspection of United States-Department of Energy (US-DOE) model 9975 nuclear materials shipping package revealed corrosion of the lead shielding that was induced by off-gas constituents from organic components in the package. Experiments were performed to determine the corrosion rate of lead when exposed to off-gas or degradation products of these organic materials. The results showed that the room temperature vulcanizing (RTV) sealant was the most corrosive organic species used in the construction of the packaging, followed by polyvinyl acetate (PVAc) glue. Fiberboard material, also used in the construction of the packaging induced corrosion to a much lesser extent than the PVAc glue and RTV sealant, and only in the presence of condensed water. The results indicated faster corrosion at temperatures higher than ambient and with condensed water. In light of these corrosion mechanisms, the lead shielding was sheathed in a stainless steel liner to mitigate against corrosion.

  6. Dose estimates in a loss of lead shielding truck accident.

    SciTech Connect (OSTI)

    Dennis, Matthew L.; Osborn, Douglas M.; Weiner, Ruth F.; Heames, Terence John (Alion Science & Technology Albuquerque, NM)

    2009-08-01T23:59:59.000Z

    The radiological transportation risk & consequence program, RADTRAN, has recently added an updated loss of lead shielding (LOS) model to it most recent version, RADTRAN 6.0. The LOS model was used to determine dose estimates to first-responders during a spent nuclear fuel transportation accident. Results varied according to the following: type of accident scenario, percent of lead slump, distance to shipment, and time spent in the area. This document presents a method of creating dose estimates for first-responders using RADTRAN with potential accident scenarios. This may be of particular interest in the event of high speed accidents or fires involving cask punctures.

  7. Comparison of leading parallel NAS file systems on commodity hardware

    SciTech Connect (OSTI)

    Hedges, R; Fitzgerald, K; Gary, M; Stearman, D M

    2010-11-08T23:59:59.000Z

    High performance computing has experienced tremendous gains in system performance over the past 20 years. Unfortunately other system capabilities, such as file I/O, have not grown commensurately. In this activity, we present the results of our tests of two leading file systems (GPFS and Lustre) on the same physical hardware. This hardware is the standard commodity storage solution in use at LLNL and, while much smaller in size, is intended to enable us to learn about differences between the two systems in terms of performance, ease of use and resilience. This work represents the first hardware consistent study of the two leading file systems that the authors are aware of.

  8. Childhood lead poisoning near abandoned lead mining and smelting areas: A case study of two affected households

    SciTech Connect (OSTI)

    Moehr, A.D. (Jasper County Health Dept., Webb City, MO (United States)); Roberts, D.W.; Phillips, P.E.; Evans, R.G.

    1993-10-01T23:59:59.000Z

    In October, 1990 the Missouri Dept. of Health entered a contract with the Agency for Toxic Substances and Disease Registry (ATSDR) to conduct an exposure study at the Jasper County, Missouri Superfund Site. The primary concern was exposure to elevated levels of lead and cadmium resulting from previous mining of lead and zinc in the area. Several individuals were found to have elevated lead levels and this article is a case study of two households where children with elevated levels resided. Due to the lowering of the Centers for Disease Control and Prevention (CDC) standard for a level of concern in childhood lead poisoning from 25 [mu]g/dl to 10 [mu]g/dl, many environmental heath personnel may be requested to evaluate exposure routes and give advice regarding risk reduction to families who reside in areas not previously thought to be problematic. Accomplishing this risk reduction may require passage of local ordinances requiring lead abatement, additional training of field personnel, and cooperative work with other public and governmental entities.

  9. PHYSICS DIVISION ESH BULLETIN 2004-02 1/15/04 LEAD SHIELDING

    E-Print Network [OSTI]

    an occupational hazard, lead dust carried home on clothing can pose a hazard to the worker's family. Lead-stops, weights for fans. · Wear gloves when handling lead. Wash your hands after handling lead. · Store lead indoors to protect from the weather and to limit oxidization. #12;· Avoid handling heavily oxidized lead

  10. Operational experiences in lead-acid batteries for photovoltaic systems

    SciTech Connect (OSTI)

    Brench, B. L.

    1981-01-01T23:59:59.000Z

    MIT Lincoln Laboratory has designed photovoltaic systems which use different kinds of lead-acid batteries, including units normally used for starting, lighting, and ignition (SLI) and for motive power. The experiences gained from four of these battery subsystems during field operation, particularly battery type versus system load, versus performance characteristics, and versus expected lifetime, are compared and analyzed.

  11. The Ground State Energy of Heavy Atoms: the Leading Correction

    E-Print Network [OSTI]

    Michael Handrek; Heinz Siedentop

    2014-11-21T23:59:59.000Z

    For heavy atoms (large atomic number $Z$) described by no-pair operators in the Furry picture we find the ground state's leading energy correction. We compare the result with (semi-)empirical values and Schwinger's prediction showing more than qualitative agreement.

  12. EFFECTS OF MERCURY, CADMIUM, AND LEAD SALTS ON

    E-Print Network [OSTI]

    buds, can cause acceler- ated regeneration, also leading to precocious molt. Heavy metals as pollutants metal pollution in industrial areas. Materials and Methods Fiddler crabs were collected in July crab, Uca pugilator. With its estuarine intertidal habitat, this crab is likely to be subject to heavy

  13. Enhanced surfaces lead to increased heat transfer and power density.

    E-Print Network [OSTI]

    Enhanced surfaces lead to increased heat transfer and power density. Inverters are used in hybrid researchers are using the coating to improve heat transfer in automotive power electron- ics devices. Photo electric vehicles (HEVs) and electric vehicles (EVs) to con- vert DC battery power into a form that can

  14. NASA Exploration and Innovation Lead to New Discoveries Five heavyweight

    E-Print Network [OSTI]

    Waliser, Duane E.

    NASA Exploration and Innovation Lead to New Discoveries Five heavyweight lifting-body designs 1960 1961 1962 19641963 1965 1966 1967 1968 19691959 Lifting Bodies 1962-1975 Gemini 1962 disposal. Weather Satellites 1960-Present NASA launched the first Television Infrared

  15. An Instability Leading to Failure of Polyethylene in Uniaxial Creep

    E-Print Network [OSTI]

    An Instability Leading to Failure of Polyethylene in Uniaxial Creep L. J. ZAPAS and J. M. CRISSMAN model, a point of instability is pre- dicted for the uniaxial creep of high density polyethylene. From dead load experiments it has been found that the instabil- ity occurs for linear -polyethylene

  16. Jefferson F. Allen Charitable Lead Annuity Graber Annuik Family Foundation

    E-Print Network [OSTI]

    Napier, Terrence

    Jefferson F. Allen Charitable Lead Annuity Trust Graber Annuik Family Foundation Helene & Allen Apter Foundation The Jeffrey H. and Shari L. Aronson Family Foundation Dexter F. and Dorothy H. Baker Foundation The Baxter Family Foundation Bayview Fund of the Community Foundation of New Jersey Frederick H

  17. Nuclear Magnetic Resonance: Portable and integrated Lead: P. Poulichet.

    E-Print Network [OSTI]

    Baudoin, Geneviève

    Nuclear Magnetic Resonance: Portable and integrated Lead: P. Poulichet. Permanent members: L. Rousseau, A. Fakri. Associated researchers: C. Delabie, A. Exertier. Portable Nuclear Magnetic Resonance : our work in the field of nuclear magneto resonance is focused on the design and the realization

  18. Research and Innovation Leading the way to a

    E-Print Network [OSTI]

    Waikato, University of

    the secrets of the Sun's energy 38 9 25 #12;1 Social and Cultural Sustainability EDUCATION FOR AN INCLUSIVE Soil microbial diversity, composting and enrichment 17 SUSTAINABLE INDUSTRIAL PROCESSES From energyResearch and Innovation Leading the way to a SUSTAINABLE FUTURE #12;Contents Message from the Vice

  19. RESEARCH Open Access Childhood lead exposure in France: benefit

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    benefits of exposure abatement. Methods: Monetary benefits were assessed in terms of avoided national costs avoided costs were included. Costs of pollutant exposure control were partially estimated in regardRESEARCH Open Access Childhood lead exposure in France: benefit estimation and partial cost

  20. Invasive species are a leading cause of animal extinctions

    E-Print Network [OSTI]

    García-Berthou, Emili

    Invasive species are a leading cause of animal extinctions Miguel Clavero and Emili Garci and extinctions of species is unproven. They analyzed the IUCN Red List database [2] and stated that only 6% of the taxa are threatened with extinction as a result of invasion by alien species and !2% (ten terrestrial

  1. 6. Fracture mechanics lead author: J, R. Rice

    E-Print Network [OSTI]

    6. Fracture mechanics lead author: J, R. Rice Division of Applied Sciences, Harvard University. F. Shih, and the ASME/AMD Technical Committee on Fracture Mechanics, pro- vided by A. S. Argon, S. N, W. D. Stuart, and R. Thomson. 6.0 ABSTRACT Fracture mechanics is an active research field

  2. Systems Engineering Leading Indicators Guide, Version 2.0

    E-Print Network [OSTI]

    Lean Advancement Initiative

    2010-06-29T23:59:59.000Z

    The Systems Engineering Leading Indicators Guide editorial team is pleased to announce the release of Version 2.0. Version 2.0 supersedes Version 1.0, which was released in July 2007 and was the result of a project initiated ...

  3. Origin of Lead in Eight Central European Peat Bogs Determined

    E-Print Network [OSTI]

    Wieder, R. Kelman

    Research Origin of Lead in Eight Central European Peat Bogs Determined from Isotope Ratios was identified in 210Pb-dated profiles through eight peat bogs distributed over an area of 60 000 km2 with Germany, Austria, and Poland. Basal peat 14C-dated at 11 000 years BP had a relatively high 206Pb/207Pb

  4. Reproductive toxicity of low-level lead exposure in men

    SciTech Connect (OSTI)

    Telisman, Spomenka [Institute for Medical Research and Occupational Health, Ksaverska cesta 2, P.O. Box 291, HR-10001 Zagreb (Croatia)], E-mail: telisman@imi.hr; Colak, Bozo [University Clinic for Diabetes, Endocrinology and Metabolic Diseases 'Vuk Vrhovac', Zagreb (Croatia); Pizent, Alica; Jurasovic, Jasna [Institute for Medical Research and Occupational Health, Ksaverska cesta 2, P.O. Box 291, HR-10001 Zagreb (Croatia); Cvitkovic, Petar [University Clinic for Diabetes, Endocrinology and Metabolic Diseases 'Vuk Vrhovac', Zagreb (Croatia)

    2007-10-15T23:59:59.000Z

    Parameters of semen quality, seminal plasma indicators of secretory function of the prostate and seminal vesicles, sex hormones in serum, and biomarkers of lead, cadmium, copper, zinc, and selenium body burden were measured in 240 Croatian men 19-52 years of age. The subjects had no occupational exposure to metals and no known other reasons suspected of influencing male reproductive function or metal metabolism. After adjusting for age, smoking, alcohol, blood cadmium, and serum copper, zinc, and selenium by multiple regression, significant (P<0.05) associations of blood lead (BPb), {delta}-aminolevulinic acid dehydratase (ALAD), and/or erythrocyte protoporphyrin (EP) with reproductive parameters indicated a lead-related increase in immature sperm concentration, in percentages of pathologic sperm, wide sperm, round sperm, and short sperm, in serum levels of testosterone and estradiol, and a decrease in seminal plasma zinc and in serum prolactin. These reproductive effects were observed at low-level lead exposure (BPb median 49 {mu}g/L, range 11-149 {mu}g/L in the 240 subjects) common for general populations worldwide. The observed significant synergistic effect of BPb and blood cadmium on increasing serum testosterone, and additive effect of a decrease in serum selenium on increasing serum testosterone, may have implications on the initiation and development of prostate cancer because testosterone augments the progress of prostate cancer in its early stages.

  5. OPTIMIZATION OF CURRENT LEADS COOLED BY NATURAL CONVECTION OF VAPOR

    E-Print Network [OSTI]

    Chang, Ho-Myung

    to HTS power systems where liquid nitrogen is continuously refrigerated by a cryocooler. The design and at the same time to employ a cryocooler for continuous operation. HTS transformers, HTS fault current limiters is constructed with non-metallic materials as in HTS transformers [2,3]. The leads in these cryostats are located

  6. Macroencapsulated and elemental lead mixed waste sites report

    SciTech Connect (OSTI)

    Kalia, A.; Jacobson, R.

    1996-09-01T23:59:59.000Z

    The purpose of this study was to compile a list of the Macroencapsulated (MACRO) and Elemental Lead (EL) Mixed Wastes sites that will be treated and require disposal at the Nevada Test Site within the next five to ten years. The five sites selected were: Hanford Site, Richland, Washington; Idaho National Engineering Laboratory (INEL), Idaho Falls, Idaho; Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee; Rocky Flats Environmental Technology (RF), Golden, Colorado; and Savannah River (SRS), Charleston, South Carolina. A summary of total lead mixed waste forms at the five selected DOE sites is described in Table E-1. This table provides a summary of total waste and grand total of the current inventory and five-year projected generation of lead mixed waste for each site. This report provides conclusions and recommendations for further investigations. The major conclusions are: (1) the quantity of lead mixed current inventory waste is 500.1 m{sup 3} located at the INEL, and (2) the five sites contain several other waste types contaminated with mercury, organics, heavy metal solids, and mixed sludges.

  7. arrestor connector lead: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    arrestor connector lead First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 and MC connectors could have a...

  8. acute lead encephalopathy: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    lead encephalopathy First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Influences of water chemistry on...

  9. azygos vein lead: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    azygos vein lead First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 AccuVein AV400 AccuVein AV400 Biology...

  10. acupuncture stimulations lead: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    acupuncture stimulations lead First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Original Research Neural...

  11. Leading Edge Nuclear Biology: What's Been Most Surprising?

    E-Print Network [OSTI]

    Pikaard, Craig

    Leading Edge Voices Nuclear Biology: What's Been Most Surprising? Restricting Genomic Partners Job with inappropriate elements. So, a major question in the field of nuclear organization is how do cells ensure have demonstrated that thousands of regulatory regions undergo activation or decommissioning even

  12. Reason, Risk and Rights: Toxins and Pollutants Lead in paint

    E-Print Network [OSTI]

    Callender, Craig

    contain many toxic chemicals...inhaled · combustion of chlorine products often leads to formation of HCl and dioxin, both of which are released into air and water · products leak, drip, break..e.g., light up chemicals · pesticides -- 500 active ingredients · 11,700 consumer products -- 1010 chemicals · electronics

  13. Start-Ups for Smarties Leading Sources of Frustration

    E-Print Network [OSTI]

    Arnold, Jonathan

    Start-Ups for Smarties 24 Leading Sources of Frustration for the Academic Entrepreneur Starting the start-up a preferential licensing deal. Some academic entrepreneurs believe that their employers should give faculty start-ups better licensing terms than they would to an unaffiliated company. Actually

  14. DOE Leads National Research Program in Gas Hydrates

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy today told Congress the agency is leading a nationwide program in search of naturally occurring natural gas hydrates - a potentially significant storehouse of methane--with far reaching implications for the environment and the nation's future energy supplies.

  15. Lead in Your Drinking Water Lead (Pb) is an extremely toxic heavy metal that unfortunately occurs widely in our environment. The

    E-Print Network [OSTI]

    Maynard, J. Barry

    Lead in Your Drinking Water Lead (Pb) is an extremely toxic heavy metal that unfortunately occurs of metallic lead in the soil (4) Drinking water ­ water as it leaves the treatment plant has no lead of connection. (In some cases, the water meter as well as the curb stop is outside the house.) Common metals

  16. Refined gluino and squark pole masses beyond leading order

    E-Print Network [OSTI]

    Stephen P. Martin

    2006-08-02T23:59:59.000Z

    The physical pole and running masses of squarks and gluinos have recently been related at two-loop order in a mass-independent renormalization scheme. I propose a general method for improvement of such formulas, and argue that better accuracy results. The improved version gives an imaginary part of the pole mass that agrees exactly with the direct calculation of the physical width at next-to-leading order. I also find the leading three-loop contributions to the gluino pole mass in the case that squarks are heavier, using effective field theory and renormalization group methods. The efficacy of these improvements for the gluino and squarks is illustrated with numerical examples. Some necessary three-loop results for gauge coupling and fermion mass beta functions and pole masses in theories with more than one type of fermion representation, which are not directly accessible from the published literature, are presented in an Appendix.

  17. NREL Leads Energy Systems Integration, Continuum Magazine: Issue 4 (Book)

    SciTech Connect (OSTI)

    Not Available

    2013-04-01T23:59:59.000Z

    Continuum Magazine showcases NREL's latest and most impactful clean energy innovations. This issue, 'NREL Leads Energy Systems Integration' explores the discipline of energy systems integration, in particular the role of the laboratory's new, one-of-a-kind Energy System Integration Facility. NREL scientists, engineers, and analysts deeply understand the fundamental science and technologies underpinning major energy producing and consuming systems, as well as the transmission infrastructure and communications and data networks required to integrate energy systems at all scales.

  18. Non-lead environmentally safe projectiles and explosive container

    DOE Patents [OSTI]

    Lowden, Richard A. (Clinton, TN); McCoig, Thomas M. (Maryville, TN); Dooley, Joseph B. (Kingston, TN); Smith, Cyrus M. (Knoxville, TN)

    1999-06-15T23:59:59.000Z

    A solid object having controlled frangibility, such as a bullet or a container for explosives, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A wetting material is deposited on the base constituent which is made of a relative dense, hard material. The wetting material enhances the wettability of the base constituent with the binder constituent, which is lighter and softer than the base constituent.

  19. Non-lead, environmentally safe projectiles and explosives containers

    DOE Patents [OSTI]

    Lowden, Richard A. (Clinton, TN); McCoig, Thomas M. (Maryville, TN); Dooley, Joseph B. (Kingston, TN); Smith, Cyrus M. (Knoxville, TN)

    2001-01-16T23:59:59.000Z

    A solid object having controlled frangibility, such as a bullet or a container for explosives, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A wetting material is deposited on the base constituent which is made of a relative dense, hard material. The wetting material enhances the wettability of the base constituent with the binder constituent, which is lighter and softer than the base constituent.

  20. Non-lead environmentally safe projectiles and explosive container

    DOE Patents [OSTI]

    Lowden, R.A.; McCoig, T.M.; Dooley, J.B.; Smith, C.M.

    1999-06-15T23:59:59.000Z

    A solid object having controlled frangibility, such as a bullet or a container for explosives, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A wetting material is deposited on the base constituent which is made of a relative dense, hard material. The wetting material enhances the wettability of the base constituent with the binder constituent, which is lighter and softer than the base constituent. 10 figs.

  1. Reactions of nitrogen heterocycle-organolithium intermediates with lead halides

    E-Print Network [OSTI]

    Kinney, Jerry Neal

    1970-01-01T23:59:59.000Z

    REACTIONS OF NITROGEN HETEROCYCLE- ORGANOLITHIUM INTERMEDIATES WITH LEAD HALIDES A Thesis by JERRY HEAL KINNEY Submitted to the Graduate College of Texas ALM University In partial fulfillment of the requirement for the degree ot MASTER... OF SCIENCE December 1970 Major Subject: Chemistry REACTIONS OF NITROGEN HETEROCYCLE- ORGANOLITHIUM INTERMEDIATES WITH LFAD HALIDES A Thesis JERRY NEAL KINNEY Approved as to style and content by: (Chairman of Commi ee) (Head of Department) (Member...

  2. Towards a characterization of fields leading to black hole hair

    E-Print Network [OSTI]

    Narayan Banerjee; Somasri Sen

    2013-07-05T23:59:59.000Z

    In the present work, it is shown that an asymptotically flat spherical black hole can have a nontrivial signature of any field for an exterior observer if the energy momentum tensor of the corresponding field is either tracefree or if the trace falls off at least as rapidly as inverse cube of the radial distance. In the absence of a general No Hair Theorem, this result can provide a characterization of the fields leading to black hole hair.

  3. (Lithium and lead-lithium corrosion and chemistry)

    SciTech Connect (OSTI)

    Tortorelli, P.F.

    1989-10-09T23:59:59.000Z

    Presentations on Mass Transport Processes in Li/Fe-12Cr-1MoVW Steel,'' A Lower Temperature Lithium Purification Process Incorporating Warm Trapping','' and Kinetic Analysis of Corrosion in Pb-17 at. % Li and Comparison to Pure Lithium'' were given by the traveler at the 1989 European Workshop on Lithium and Lead-Lithium Corrosion and Chemistry in Vienna, Austria. The European effort in lead-lithium appeared to be continuing unabated with a future focus on deposition and surface products reactions that can lead to corrosion control. The temperature gain realized from the use of ferritic/martensitic steels instead of austenitic steels in Pb-17 at. % Li appears to be 25--50{degrees}C. The traveler also visited the European Community's Joint Research Centre at Ispra to discuss Fe-Mn-Cr steels. He presented a seminar on Recent ORNL Results on the Development of Fe-Mn-Cr Steels,'' and toured the liquid metal laboratories. Our developmental Fe-Mn-Cr steels, which are compositionally tailored for shallow land burial, would not qualify as low activation'' materials per European standards. Because of both this and the poor sensitization resistance of these steels, our alloy development strategy for reduced activation materials should be critically reviewed.

  4. MOX Lead Assembly Fabrication at the Savannah River Site

    SciTech Connect (OSTI)

    Geddes, R.L. [Westinghouse Savannah River Company, AIKEN, SC (United States); Spiker, D.L.; Poon, A.P.

    1997-12-01T23:59:59.000Z

    The U. S. Department of Energy (DOE) announced its intent to prepare an Environmental Impact Statement (EIS) under the National Environmental Policy Act (NEPA) on the disposition of the nations weapon-usable surplus plutonium.This EIS is tiered from the Storage and Disposition of Weapons-Usable Fissile Material Programmatic Environmental Impact Statement issued in December 1996,and the associated Record of Decision issued on January, 1997. The EIS will examine reasonable alternatives and potential environmental impacts for the proposed siting, construction, and operation of three types of facilities for plutonium disposition. The three types of facilities are: a pit disassembly and conversion facility, a facility to immobilize surplus plutonium in a glass or ceramic form for disposition, and a facility to fabricate plutonium oxide into mixed oxide (MOX) fuel.As an integral part of the surplus plutonium program, Oak Ridge National Laboratory (ORNL) was tasked by the DOE Office of Fissile Material Disposition(MD) as the technical lead to organize and evaluate existing facilities in the DOE complex which may meet MD`s need for a domestic MOX fuel fabrication demonstration facility. The Lead Assembly (LA) facility is to produce 1 MT of usable test fuel per year for three years. The Savannah River Site (SRS) as the only operating plutonium processing site in the DOE complex, proposes two options to carry out the fabrication of MOX fuel lead test assemblies: an all Category I facility option and a combined Category I and non-Category I facilities option.

  5. Rapid sonochemical preparation of shape-selective lead iodide

    SciTech Connect (OSTI)

    Huang, Baojun [Key Laboratory of Micro-Nano Materials for Energy Storage and Conversion of Henan Province, Institute of Surface Micro and Nano Materials, Xuchang University, Xuchang, Henan 461000 (China)] [Key Laboratory of Micro-Nano Materials for Energy Storage and Conversion of Henan Province, Institute of Surface Micro and Nano Materials, Xuchang University, Xuchang, Henan 461000 (China); He, Qin [College of Chemistry and Chemical Engineering, Xuchang University, Xuchang, Henan 461000 (China)] [College of Chemistry and Chemical Engineering, Xuchang University, Xuchang, Henan 461000 (China); Fa, Wenjun; Li, Pinjiang; Zhang, Yange [Key Laboratory of Micro-Nano Materials for Energy Storage and Conversion of Henan Province, Institute of Surface Micro and Nano Materials, Xuchang University, Xuchang, Henan 461000 (China)] [Key Laboratory of Micro-Nano Materials for Energy Storage and Conversion of Henan Province, Institute of Surface Micro and Nano Materials, Xuchang University, Xuchang, Henan 461000 (China); Zheng, Zhi, E-mail: zzheng@xcu.edu.cn [Key Laboratory of Micro-Nano Materials for Energy Storage and Conversion of Henan Province, Institute of Surface Micro and Nano Materials, Xuchang University, Xuchang, Henan 461000 (China)] [Key Laboratory of Micro-Nano Materials for Energy Storage and Conversion of Henan Province, Institute of Surface Micro and Nano Materials, Xuchang University, Xuchang, Henan 461000 (China)

    2012-09-15T23:59:59.000Z

    Graphical abstract: SEM morphologies of various PbI2 products obtained with the iodine concentration of 6.7 g/L and irradiation time of 1 minute at the reaction temperatures of 35 °C (a), 25 °C (b), and 15 °C (c). Highlights: ? PbI{sub 2} with various morphologies were rapidly formed at room temperature. ? We could well control the morphologies of PbI{sub 2} by changing reaction conditions. ? The PbI{sub 2} films could better resist rolling in a liquid media. -- Abstract: Lead iodide (PbI{sub 2}) films/crystals with various nano/micro morphologies (e.g., Nanoflake, block and microrod) were rapidly synthesized by taking advantage of a simple sonochemical method. The PbI{sub 2} crystals with uniform nanoflake structures could be fabricated directly on lead foils with the irradiation time as short as 36 s via interfacial reaction between lead foils and elemental iodine in ethanol at ambient temperature. It was found experimentally that the morphologies of the resulting thin films/crystals could be well controlled by the adjustment of several parameters including irradiation time, reaction solvents, iodine concentration, ultrasonic power, and reaction temperature. Most importantly, the resultant PbI{sub 2} films are stable enough to resist rolling under the drastic ultrasound irradiation in a liquid media. This method is believed to be the fastest way for in situ fabrication of morphology-controlled semiconductor films on various metal substrates for subsequent applications related to the other metal iodide or metal sulfide semiconductor films.

  6. Use of Chemical Inventory Accuracy Measurements as Leading Indicators

    SciTech Connect (OSTI)

    Quigley, David; Freshwater, David; Alnajjar, Mikhail S.; Siegel, Dina; Kuntamukkula, Murty; Simmons, Fred

    2012-05-15T23:59:59.000Z

    Chemical safety and lifecycle management (CSLM) is a process that involves managing chemicals and chemical information from the moment someone begins to order a chemical and lasts through final disposition(1). Central to CSLM is tracking data associated with chemicals which, for the purposes of this paper, is termed the chemical inventory. Examples of data that could be tracked include chemical identity, location, quantity, date procured, container type, and physical state. The reason why so much data is tracked is that the chemical inventory supports many functions. These functions include emergency management, which depends upon the data to more effectively plan for, and respond to, chemical accidents; environmental management that uses inventory information to aid in the generation of various federally-mandated and other regulatory reports; and chemical management that uses the information to increase the efficiency and safety with which chemicals are stored and utilized. All of the benefits of having an inventory are predicated upon having an inventory that is reasonably accurate. Because of the importance of ensuring one's chemical inventory is accurate, many have become concerned about measuring inventory accuracy. But beyond providing a measure of confidence in information gleaned from the inventory, does the inventory accuracy measurement provide any additional function? The answer is 'Yes'. It provides valuable information that can be used as a leading indicator to gauge the health of a chemical management system. In this paper, we will discuss: (1) what properties make leading indicators effective, (2) how chemical inventories can be used as a leading indicator, (3) how chemical inventory accuracy can be measured, what levels of accuracies should realistically be expected in a healthy system, and (4) what a subpar inventory accuracy measurement portends.

  7. USE OF CHEMICAL INVENTORY ACCURACY MEASUREMENTS AS LEADING INDICATORS

    SciTech Connect (OSTI)

    Kuntamukkula, M.

    2011-02-10T23:59:59.000Z

    Chemical safety and lifecycle management (CSLM) is a process that involves managing chemicals and chemical information from the moment someone begins to order a chemical and lasts through final disposition(1). Central to CSLM is tracking data associated with chemicals which, for the purposes of this paper, is termed the chemical inventory. Examples of data that could be tracked include chemical identity, location, quantity, date procured, container type, and physical state. The reason why so much data is tracked is that the chemical inventory supports many functions. These functions include emergency management, which depends upon the data to more effectively plan for, and respond to, chemical accidents; environmental management that uses inventory information to aid in the generation of various federally-mandated and other regulatory reports; and chemical management that uses the information to increase the efficiency and safety with which chemicals are stored and utilized. All of the benefits of having an inventory are predicated upon having an inventory that is reasonably accurate. Because of the importance of ensuring one's chemical inventory is accurate, many have become concerned about measuring inventory accuracy. But beyond providing a measure of confidence in information gleaned from the inventory, does the inventory accuracy measurement provide any additional function? The answer is 'Yes'. It provides valuable information that can be used as a leading indicator to gauge the health of a chemical management system. In this paper, we will discuss: what properties make leading indicators effective, how chemical inventories can be used as a leading indicator, how chemical inventory accuracy can be measured, what levels of accuracies should realistically be expected in a healthy system, and what a subpar inventory accuracy measurement portends.

  8. Report on First Activations with the Lead Slowing Down Spectrometer

    SciTech Connect (OSTI)

    Warren, Glen A.; Mace, Emily K.; Pratt, Sharon L.; Stave, Sean; Woodring, Mitchell L.

    2011-03-03T23:59:59.000Z

    On Feb. 17 and 18 2011, six items were irradiated with neutrons using the Lead Slowing Down Spectrometer. After irradiation, dose measurements and gamma-spectrometry measurements were completed on all of the samples. No contamination was found on the samples, and all but one provided no dose. Gamma-spectroscopy measurements qualitatively agreed with expectations based on the materials, with the exception of silver. We observed activation in the room in general, mostly due to 56Mn and 24Na. Most of the activation was short lived, with half-lives on the scale of hours, except for 198Au which has a half-life of 2.7 d.

  9. MTBE growth limited despite lead phasedown in gasoline

    SciTech Connect (OSTI)

    Storck, W.

    1985-07-15T23:59:59.000Z

    This month's legislated reduction of the allowable amount of lead additives in gasoline will increase demand strongly for methyl-tert-butyl ether (MTBE) as an octane enhancer, but the economics of the refinery business and the likelihood of rapidly increasing high-octane gasoline imports probably will limit the size of the business in coming years. MTBE will be used to fill the octane gap now, but economics and imports of gasoline later on could hold down demand. The limited growth in sales of MTBE is discussed.

  10. Chemical deposition of thin films of lead selenide

    E-Print Network [OSTI]

    Skovlin, Dean Oliver

    1956-01-01T23:59:59.000Z

    formed after a period of three minutes. When concentrated ammonium hydroxide wss added to such a reaction mixture, gross precipitation of lead selenide took place immediately. A thin and spotty mirror also formed on the glass wall of the test tube.... Attempts were made to obtain a more even and ccsnplete mirroring by varying the concentration of the ammonium hydroxide in the solution, but all such attempts met with little success. The addition of four drops of 3N assaonium hydroxide resulted in a...

  11. Alkali-lead-iron phosphate glass and associated method

    DOE Patents [OSTI]

    Boatner, L.A.; Sales, B.C.; Franco, S.C.S.

    1994-03-29T23:59:59.000Z

    A glass composition and method of preparation utilizes a mixture consisting of phosphorus oxide within the range of about 40 to 49 molar percent, lead oxide within the range of about 10 to 25 molar percent, iron oxide within the range of about 10 to 17 molar percent and an alkali oxide within the range of about 23 to 30 molar percent. The glass resulting from the melting and subsequent solidifying of the mixture possesses a high degree of durability and a coefficient of thermal expansion as high as that of any of a number of metals. Such features render this glass highly desirable in glass-to-metal seal applications. 6 figures.

  12. Alkali-lead-iron phosphate glass and associated method

    DOE Patents [OSTI]

    Boatner, Lynn A. (Oak Ridge, TN); Sales, Brian C. (Knoxville, TN); Franco, Sofia C. S. (Santafe de Bogota, CO)

    1994-01-01T23:59:59.000Z

    A glass composition and method of preparation utilizes a mixture consisting of phosphorus oxide within the range of about 40 to 49 molar percent, lead oxide within the range of about 10 to 25 molar percent, iron oxide within the range of about 10 to 17 molar percent and an alkali oxide within the range of about 23 to 30 molar percent. The glass resulting from the melting and subsequent solidifying of the mixture possesses a high degree of durability and a coefficient of thermal expansion as high as that of any of a number of metals. Such features render this glass highly desirable in glass-to-metal seal applications.

  13. Hanford Leads the Way for Greener Classrooms | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGY TAX POLICIES7.pdfFuel Celland Contractors | DepartmentHANFORDHaier:FriendsLeads the

  14. Lead-Free Solder Paste | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceE C H N I C A L TA L K <Lead-Free

  15. Lester to lead ORISE's scientific and technical peer review program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceE C HLester to lead ORISE's scientific

  16. Leading the Charge: Tribal Women in Power | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector General Office0-72.pdfGeorgeDoesn't Happen to HighJosephNOx Traps forLM2LarryLawsHaroldLeading the

  17. Women Engineers Lead Global Innovation in Bangalore | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched FerromagnetismWaste and MaterialsWenjun DengWISPWind Industry2WChinnSueBacaLead

  18. Leading the Nation in Clean Energy Deployment | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensionalthe10 DOEWashington,LM-04-XXXXLocated atPenroseDepartmentLeading

  19. Advanced Lead Acid Battery Consortium | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating SolarElectric Coop,SaveWhiskeyEnergyAd-VentaAddison is aAdenaAdrian isLead Acid

  20. Protocol, Site Leads - May 2011 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department ofT ib l L dDepartment of Energy 0 DOEProtocol forSite Leads - May 2011

  1. Alternative Fuels Data Center: San Diego Leads in Promoting EVs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth (AOD)ProductssondeadjustsondeadjustAbout theOFFICE OFFuelsPropane Tank OverfillSan Diego Leads in Promoting

  2. GAS COOLED ELECTRICAL LEADS FOR USE ON FORCED COOLED SUPERCONDUCTING MAGNETS

    E-Print Network [OSTI]

    Smits, R.G.

    2010-01-01T23:59:59.000Z

    11-14, 1981 GAS COOLED ELECTRICAL LEADS FOR USE ON FORCEDim mumii P mm GAS COOLED ELECTRICAL LEADS FOR USE ON FORCEDD. Henning, "Cryogenic Electrical Leads," Proceedings of the

  3. Maternal Blood Lead Levels and the Risk of Pregnancy Induced Hypertension. The "EDEN" Cohort Study.

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Maternal Blood Lead Levels and the Risk of Pregnancy Induced Hypertension. The "EDEN" Cohort title: Lead and Gestational Hypertension Key words: cadmium; environmental health; epidemiology; gestation; hypertension; lead; manganese. Acknowledgments: We are indebted to the participating families

  4. Survey of mercury, cadmium and lead content of household batteries

    SciTech Connect (OSTI)

    Recknagel, Sebastian, E-mail: sebastian.recknagel@bam.de [BAM Federal Institute for Materials Research and Testing, Department of Analytical Chemistry, Reference Materials, Richard-Willstätter-Straße 11, D-12489 Berlin (Germany); Radant, Hendrik [BAM Federal Institute for Materials Research and Testing, Department of Analytical Chemistry, Reference Materials, Richard-Willstätter-Straße 11, D-12489 Berlin (Germany); Kohlmeyer, Regina [German Federal Environment Agency (UBA), Section III 1.6 Extended Producer Responsibility, Wörlitzer Platz 1, D-06844 Dessau-Roßlau (Germany)

    2014-01-15T23:59:59.000Z

    Highlights: • A well selected sample of 146 batteries was analysed for its heavy metals content. • A comparison was made between heavy metals contents in batteries in 2006 and 2011. • No significant change after implementation of the new EU Batteries Directive. • Severe differences in heavy metal contents were found in different battery-types. - Abstract: The objective of this work was to provide updated information on the development of the potential impact of heavy metal containing batteries on municipal waste and battery recycling processes following transposition of the new EU Batteries Directive 2006/66/EC. A representative sample of 146 different types of commercially available dry and button cells as well as lithium-ion accumulators for mobile phones were analysed for their mercury (Hg)-, cadmium (Cd)- and lead (Pb)-contents. The methods used for preparing the cells and analysing the heavy metals Hg, Cd, and Pb were either developed during a former study or newly developed. Several batteries contained higher mass fractions of mercury or cadmium than the EU limits. Only half of the batteries with mercury and/or lead fractions above the marking thresholds were labelled. Alkaline–manganese mono-cells and Li-ion accumulators, on average, contained the lowest heavy metal concentrations, while zinc–carbon batteries, on average, contained the highest levels.

  5. A two-dimensional mathematical model of a porous lead dioxide electrode in a lead-acid cell

    E-Print Network [OSTI]

    Dimpault-Darcy, Eric Christophe

    2012-06-07T23:59:59.000Z

    (ir? irs) MODEL DEVELOPMENT 9 11 12 13 14 14 15 15 16 17 V. A. Divergence oi' Current B. Porosity Balance C. Electrode Kinetics D. Ohm's Lave in Solution E. Electrolyte Material Balance NUMERICAL SOLUTION TECHNIQUE 18 19 20 22 24... of the active species within the porous electrodes using a macroscopic approach, and apply a Butler-Volmer type polarization equation. Simonsson (9) and Micka and Rousar (10-13) concentrate their efforts on the porous electrodes of the lead-acid battery...

  6. E-Print Network 3.0 - anthropogenic lead distribution Sample...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    lead distribution Page: << < 1 2 3 4 5 > >> 1 Inverse estimates of anthropogenic CO2 uptake, transport, and storage by the ocean Summary: ., 2003. This leads to low...

  7. Leading without Followers: How Politics and Market Dynamics Trapped Innovations in Japan's Domestic Galapagos Telecommunications Sector

    E-Print Network [OSTI]

    Kushida, Kenji E

    2011-01-01T23:59:59.000Z

    Japan leading without followers in telecommunications by presenting the four technologyJapan’s domestic telecommunications market from global markets despite leading in particular technologies

  8. E-Print Network 3.0 - atmospheric lead fall-out Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of decades, adding carbon dioxide to the atmosphere will lead... to an enhanced greenhouse effect by trapping additional heat in the lower atmosphere, leading to increases... and...

  9. E-Print Network 3.0 - antiferroelectric lead zirconate Sample...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    understanding of the mechanisms for lead loss and causes for discordance in zircon... .2. Uranium-lead analyses of zircon core ... Source: Chamberlain, C. Page - Department of...

  10. Compatibility of lead-free solders with lead containing surface finishes as a reliability issue in electronic assemblies

    SciTech Connect (OSTI)

    Vianco, P.; Rejent, J. [Sandia National Labs., Albuquerque, NM (United States); Artaki, I.; Ray, U.; Finley, D.; Jackson, A. [AT and T Bell Labs., Princeton, NJ (United States)

    1996-03-01T23:59:59.000Z

    Enhanced performance goals and environmental restrictions have heightened the consideration for use of alternative solders as replacements for the traditional tin-lead (Sn-Pb) eutectic and near-eutectic alloys. However, the implementation of non-Pb bearing surface finishes may lag behind solder alloy development. A study was performed which examined the effect(s) of Pb contamination on the performance of Sn-Ag-Bi and Sn-Ag-Cu-Sb lead-free solders by the controlled addition of 63Sn-37Pb solder at levels of 0.5 {minus} 8.0 wt.%. Thermal analysis and ring-in-plug shear strength studies were conducted on bulk solder properties. Circuit board prototype studies centered on the performance of 20I/O SOIC gull wing joints. Both alloys exhibited declines in their melting temperatures with greater Sn-Pb additions. The ring-in-plug shear strength of the Sn-Ag-Cu-Sb solder increased slightly with Sn-Pb levels while the Sn-Ag-Bi alloy experienced a strength loss. The mechanical behavior of the SOIC (Small Outline Integrated Circuit) Sn-Ag-Bi solder joints reproduced the strength levels were insensitive to 10,106 thermal cycles. The Sn-Ag-Cu-Sb solder showed a slight decrease in the gull wing joint strengths that was sensitive to the Pb content of the surface finish.

  11. Design of an Actinide-Burning, Lead or Lead-Bismuth Cooled Reactor that Produces Low-Cost Electricity

    SciTech Connect (OSTI)

    Mac Donald, Philip Elsworth; Weaver, Kevan Dean; Davis, Cliff Bybee; MIT folks

    2000-07-01T23:59:59.000Z

    The purpose of this Idaho National Engineering and Environmental Laboratory (INEEL) and Massachusetts Institute of Technology (MIT) University Research Consortium (URC) project is to investigate the suitability of lead or lead-bismuth cooled fast reactors for producing low-cost electricity as well as for actinide burning. The goal is to identify and analyze the key technical issues in core neutronics, materials, thermal-hydraulics, fuels, and economics associated with the development of this reactor concept. Work has been accomplished in four major areas of research: core neutronic design, material compatibility, plant engineering, and coolant activation. In the area of core neutronic design, the reactivity vs. burnup and discharge isotopics of both non-fertile and fertile fuels were evaluated. An innovative core for pure actinide burning that uses streaming, fertile-free fuel assemblies was studied in depth. This particular core exhibits excellent reactivity performance upon coolant voiding, even for voids that occur in the core center, and has a transuranic (TRU) destruction rate that is comparable to the proposed accelerator transmutation of waste (ATW) facility. These studies suggest that a core can be designed to achieve a long life while maintaining safety and minimizing waste. In the area of material compatibility studies, an experimental apparatus for the investigation of the flow-assisted dissolution and precipitation (corrosion) of potential fuel cladding and structural materials has been designed and built at the INEEL. The INEEL forced-convection corrosion cell consists of a small heated vessel with a shroud and gas flow system. The corrosion cell is being used to test steel that is commercially available in the United States to temperatures above 650°C. Progress in plant engineering was made for two reactor concepts, one utilizing an indirect cycle with heat exchangers and the other utilizing a direct-contact steam cycle. The evaluation of the indirect cycle designs has investigated the effects of various parameters to increase electric production at full power. For the direct-contact reactor, major issues related to the direct-contact heat transfer rate and entrainment and carryover of liquid lead-bismuth to the turbine have been identified and analyzed. An economic analysis approach was also developed to determine the cost of electricity production in the lead-bismuth reactor. The approach will be formulated into a model and applied to develop scientific cost estimates for the different reactor designs and thus aid in the selection of the most economic option. In the area of lead-bismuth coolant activation, the radiological hazard was evaluated with particular emphasis on the direct-contact reactor. In this system, the lack of a physical barrier between the primary and secondary coolant favors the release of the alpha-emitter Po?210 and its transport throughout the plant. Modeling undertaken on the basis of the scarce information available in the literature confirmed the importance of this issue, as well as the need for experimental work to reduce the uncertainties on the basic characteristics of volatile polonium chemical forms.

  12. Report on Second Activations with the Lead Slowing Down Spectrometer

    SciTech Connect (OSTI)

    Stave, Sean C.; Mace, Emily K.; Pratt, Sharon L.; Warren, Glen A.

    2012-04-27T23:59:59.000Z

    Summary On August 18 and 19 2011, five items were irradiated with neutrons using the Lead Slowing Down Spectrometer (LSDS). After irradiation, dose measurements and gamma-spectrometry measurements were completed on all of the samples. No contamination was found on the samples, and all but one provided no dose. Gamma-spectroscopy measurements qualitatively agreed with expectations based on the materials. As during the first activation run, we observed activation in the room in general, mostly due to 56Mn and 24Na. Most of the activation of the samples was short lived, with half-lives on the scale of hours to days, except for 60Co which has a half-life of 5.3 y.

  13. Lead acid battery pulse discharge investigation. Final report

    SciTech Connect (OSTI)

    Dowgiallo, E

    1980-04-01T23:59:59.000Z

    The effects of high current pulses caused by electric vehicle silicon-controlled rectifier and transistor chopper controllers on battery energy, lifetime, and microstructure were studied. Test equipment and results are described. It was found that the energy of improved golf cart-type batteries deteriorated under pulsed conditions by about 10% with respect to dc conditions for pulses between 16 and 333 Hz - no difference was noted above 333 Hz. Frequencies and duty cycles characteristic of electric vehicle controllers produce ampere-hour capacities similar in magnitude to dc discharges of the same average currents. The amount of positive plate corrosion under pulsed conditions was about twice that ot the unpulsed. Unusually large lead sulfate crystals were found in isolated colonies in pulsed plates, whereas a battery that had been discharged each cycle at an equivalent steady state did not show these large crystals. 5 figures, 3 tables. (RWR)

  14. Rapid Depresurizations: Can they lead to irreversible damage?

    E-Print Network [OSTI]

    Berest, Pierre; Brouard, Benoît; Hévin, Grégoire

    2013-01-01T23:59:59.000Z

    Rapid gas depressurization leads to gas cooling that is followed by slow gas warming when the cavern is kept idle. The decrease in the temperature of gas depends upon the relative withdrawal rate (in %/day), and cavern size and shape. Gas cooling may result in the onset of tensile stresses at cavern walls and roofs that may generate fractures or cracks. However, in most cases, the depth of penetration of these fractures is small, and they are perpendicular to the cavern wall. The distance between two parallel fractures becomes larger when fractures penetrate deeper into the rock mass, as some fractures stop growing. Fractures form a polygonal pattern. Salt slabs are created, with boundaries formed by the opened fractures. As long as the depth of penetration of the fracture remains small, these slabs remain strongly bonded to the rock mass, and it is believed that, in many cases, their weights are not large enough to allow them to break off the cavern wall.

  15. Atomic vapor laser isotope separation of lead-210 isotope

    DOE Patents [OSTI]

    Scheibner, Karl F. (Tracy, CA); Haynam, Christopher A. (Pleasanton, CA); Johnson, Michael A. (Pleasanton, CA); Worden, Earl F. (Diablo, CA)

    1999-01-01T23:59:59.000Z

    An isotopically selective laser process and apparatus for removal of Pb-210 from natural lead that involves a one-photon near-resonant, two-photon resonant excitation of one or more Rydberg levels, followed by field ionization and then electrostatic extraction. The wavelength to the near-resonant intermediate state is counter propagated with respect to the second wavelength required to populate the final Rydberg state. This scheme takes advantage of the large first excited state cross section, and only modest laser fluences are required. The non-resonant process helps to avoid two problems: first, stimulated Raman Gain due to the nearby F=3/2 hyperfine component of Pb-207 and, second, direct absorption of the first transition process light by Pb-207.

  16. Atomic vapor laser isotope separation of lead-210 isotope

    DOE Patents [OSTI]

    Scheibner, K.F.; Haynam, C.A.; Johnson, M.A.; Worden, E.F.

    1999-08-31T23:59:59.000Z

    An isotopically selective laser process and apparatus for removal of Pb-210 from natural lead that involves a one-photon near-resonant, two-photon resonant excitation of one or more Rydberg levels, followed by field ionization and then electrostatic extraction. The wavelength to the near-resonant intermediate state is counter propagated with respect to the second wavelength required to populate the final Rydberg state. This scheme takes advantage of the large first excited state cross section, and only modest laser fluences are required. The non-resonant process helps to avoid two problems: first, stimulated Raman Gain due to the nearby F=3/2 hyperfine component of Pb-207 and, second, direct absorption of the first transition process light by Pb-207. 5 figs.

  17. Non-global logarithms at finite Nc beyond leading order

    E-Print Network [OSTI]

    Khelifa-Kerfa, Kamel

    2015-01-01T23:59:59.000Z

    We analytically compute non-global logarithms at finite Nc fully up to 4 loops and partially at 5 loops, for the hemisphere mass distribution in e+e- to di-jets to leading logarithmic accuracy. Our method of calculation relies solely on integrating the eikonal squared-amplitudes for the emission of soft energy-ordered real-virtual gluons over the appropriate phase space. We show that the series of non-global logarithms in the said distribution exhibits a pattern of exponentiation thus confirming - by means of brute force - previous findings. In the large-Nc limit, our results coincide with those recently reported in literature. A comparison of our proposed exponential form with all-orders numerical solutions is performed and the phenomenological impact of the finite-Nc corrections is discussed.

  18. Optical properties and structure of beryllium lead silicate glasses

    SciTech Connect (OSTI)

    Zhidkov, I. S., E-mail: i.s.zhidkov@urfu.ru [Ural Federal University, Mira Str. 19, Yekaterinburg, 620002, Russia and Institute of Metal Physics, Russian Academy of Sciences-Ural Division, S. Kovalevskoi Str. 18, 620990 Yekaterinburg (Russian Federation); Zatsepin, A. F.; Cholakh, S. O.; Kuznetsova, Yu. A. [Ural Federal University, Mira Str. 19, Yekaterinburg, 620002 (Russian Federation)

    2014-10-21T23:59:59.000Z

    Luminescence and optical properties and structural features of (BeO){sub x}(PbO?SiO{sub 2}){sub 1?x} glasses (x = 0 ÷ 0.3) are investigated by means of optical absorption and photoluminescence spectroscopy and X-ray diffraction. The regularities of the formation of the optical absorption edge and static disorder are studied. It is shown that the optical absorption and luminescence are determined by transitions between localized states of lead ions. The impact of beryllium oxide on optical and luminescence properties and electronic structure of bands tails is discussed. The presence of two different concentration ranges with various short-range order structure and band tails nature has been established.

  19. Almost everyone knows that lead-based paint caused serious health problems

    E-Print Network [OSTI]

    such as contaminat- ed food and drinking water. Imported foods in lead- soldered cans and foods served in lead. It accumulates in the body and can cause lead poisoning. Even at low concen- trations, when there are no outward poisoning may diminish if the source of exposure is removed, but some damage is permanent. Symptoms of lead

  20. Detecting acute myocardial infarction in the 12-lead ECG using Hermite expansions

    E-Print Network [OSTI]

    Lunds Universitet,

    Detecting acute myocardial infarction in the 12-lead ECG using Hermite expansions and neural-lead ECG, together with patient history and biochemical markers, are usually used at the emergency to rely on the 12-lead ECG together with patient history. The 12-lead ECG has the advantage of always

  1. Cadmium, lead and mercury exposure in non smoking pregnant women

    SciTech Connect (OSTI)

    Hinwood, A.L., E-mail: a.hinwood@ecu.edu.au [Centre for Ecosystem Management, Edith Cowan University, 270 Joondalup Drive, Joondalup, WA 6027 (Australia); Callan, A.C.; Ramalingam, M.; Boyce, M. [Centre for Ecosystem Management, Edith Cowan University, 270 Joondalup Drive, Joondalup, WA 6027 (Australia)] [Centre for Ecosystem Management, Edith Cowan University, 270 Joondalup Drive, Joondalup, WA 6027 (Australia); Heyworth, J. [School Population Health, The University of Western Australia, 35 Stirling Highway Crawley, WA 6009 (Australia)] [School Population Health, The University of Western Australia, 35 Stirling Highway Crawley, WA 6009 (Australia); McCafferty, P. [ChemCentre, PO Box 1250, Bentley, WA 6983 (Australia)] [ChemCentre, PO Box 1250, Bentley, WA 6983 (Australia); Odland, J.Ř. [Department of Community Medicine, University of Tromsř, N-9037 Tromsř (Norway)] [Department of Community Medicine, University of Tromsř, N-9037 Tromsř (Norway)

    2013-10-15T23:59:59.000Z

    Recent literature suggests that exposure to low concentrations of heavy metals may affect both maternal and child health. This study aimed to determine the biological heavy metals concentrations of pregnant women as well as environmental and dietary factors that may influence exposure concentrations. One hundred and seventy three pregnant women were recruited from Western Australia, each providing a sample of blood, first morning void urine, residential soil, dust and drinking water samples. Participants also completed a questionnaire which included a food frequency component. All biological and environmental samples were analysed for heavy metals using ICP-MS. Biological and environmental concentrations of lead and mercury were generally low (Median Pb Drinking Water (DW) 0.04 µg/L; Pb soil <3.0 µg/g; Pb dust 16.5 µg/g; Pb blood 3.67 µg/L; Pb urine 0.55; µg/L Hg DW <0.03; Hg soil <1.0 µg/g; Hg dust <1.0 µg/g; Hg blood 0.46 µg/L; Hg urine <0.40 µg/L). Cadmium concentrations were low in environmental samples (Median CdDW 0.02 µg/L; Cdsoil <0.30 ug/g; Cddust <0.30) but elevated in urine samples (Median 0.55 µg/L, creatinine corrected 0.70 µg/g (range <0.2–7.06 µg/g creatinine) compared with other studies of pregnant women. Predictors of increased biological metals concentrations in regression models for blood cadmium were residing in the Great Southern region of Western Australia and not using iron/folic acid supplements and for urinary cadmium was having lower household annual income. However, these factors explained little of the variation in respective biological metals concentrations. The importance of establishing factors that influence low human exposure concentrations is becoming critical in efforts to reduce exposures and hence the potential for adverse health effects. -- Highlights: • Biological heavy metals concentrations in women in their 3rd trimester of pregnancy. • Exposure assessment including environmental, lifestyle and activity data. • Urinary cadmium concentrations were elevated in this group of pregnant women. • Blood lead and mercury concentrations were below recommended biological guideline values.

  2. Hydrogen diffusion in Lead Zirconate Titanate and Barium Titanate

    SciTech Connect (OSTI)

    Alvine, Kyle J.; Vijayakumar, M.; Bowden, Mark E.; Schemer-Kohrn, Alan L.; Pitman, Stan G.

    2012-08-28T23:59:59.000Z

    Hydrogen is a potential clean-burning, next-generation fuel for vehicle and stationary power. Unfortunately, hydrogen is also well known to have serious materials compatibility issues in metals, polymers, and ceramics. Piezoelectric actuator materials proposed for low-cost, high efficiency high-pressure hydrogen internal combustion engines (HICE) are known to degrade rapidly in hydrogen. This limits their potential use and poses challenges for HICE. Hydrogen-induced degradation of piezoelectrics is also an issue for low-pressure hydrogen passivation in ferroelectric random access memory. Currently, there is a lack of data in the literature on hydrogen species diffusion in piezoelectrics in the temperature range appropriate for the HICE as charged via a gaseous route. We present 1HNMR quantification of the local hydrogen species diffusion within lead zirconate titanate and barium titanate on samples charged by exposure to high-pressure gaseous hydrogen ?32?MPa. Results are discussed in context of theoretically predicted interstitial hydrogen lattice sites and aqueous charging experiments from existing literature.

  3. Microchemical investigations of dust emitted by a lead smelter

    SciTech Connect (OSTI)

    Sobanska, S.; Ricq, N. [Ecole des Mines de Douai (France). Dept. Chimie et Environnement] [Ecole des Mines de Douai (France). Dept. Chimie et Environnement; [Univ. de Lille I, Villeneuve d`Ascq (France); Laboudigue, A.; Guillermo, R. [Ecole des Mines de Douai (France). Dept. Chimie et Environnement] [Ecole des Mines de Douai (France). Dept. Chimie et Environnement; Bremard, C.; Laureyns, J.; Merlin, J.C.; Wignacourt, J.P. [Univ. de Lille I, Villeneuve d`Ascq (France)] [Univ. de Lille I, Villeneuve d`Ascq (France)

    1999-05-01T23:59:59.000Z

    Dusts emitted by an important pyrometallurgical lead smelter have been sampled within the pipes of the grilling and furnace working units before and after the filtering systems, respectively. Particle size distribution, elementary analyses, and X-ray powder diffraction analysis indicate PbS, PbSO{sub 4}, PbSO{sub 4}{center_dot}PbO, Pb, ZnS small particles less than 5 {micro}m in size to contribute mainly to the current atmospheric pollution. Although at least 90% of dust are retained on the filters, the amounts of the respirable smaller particles are significantly larger in the current emission. The average chemical speciation was found to be analogous for the dust samples collected before and after the filters. The scanning electron microscopy associated with energy-dispersive X-ray analysis and Raman microspectrometry established the morphology and chemical composition at the level of individual particles. A lot of minor compounds were found as small heterogeneous individual particles in the heterogeneous particles of grilling dust. Among the homogeneous particles of furnace dust, amorphous C, {beta}-PbO, PbO-PbCl{sub 2}, FeO, CdS, CdSO{sub 4} were often detected as homogeneous mixtures with the major compounds within the particles.

  4. Mutagenicity in the vicinity of a lead smelter

    SciTech Connect (OSTI)

    Lower, W.R.; Thompson, W.A.; Drobney, V.K.; Yanders, A.F.

    1983-01-01T23:59:59.000Z

    The mutagenicity of the environment in the vicinity of a lead smelter was examined for 3 years by studies of changes in the frequencies of male germinal mutations of the waxy-C system of Zea mays and somatic mutations of the stamen hair system of Tradescantia. A transect was run at 0.3, 1.7, 3.2, 7.4, and 11.4 km predominantly downwind from the smelter. The mutagenic responses vary between years, within a year, and with distance. Mutation frequencies are both directional and nondirectional with distance. Concentrations of Pb, Cd, Cu, and Zn measured in soil samples show directional changes with distance each of the 3 years, and joint monotonicity is observed in some cases between mutation frequency with distance and metal concentrations with distance. Of a total of ten experiments with both Zea mays and Tradescantia, eight show significantly higher mutation frequencies at one or more locations close to the smelter than at locations more distant or at other controls.

  5. Analysis of leaded and unleaded gasoline pricing. Final report

    SciTech Connect (OSTI)

    Not Available

    1985-03-15T23:59:59.000Z

    This report summarizes the evaluation of the cost price relation between the two fuels. The original scope of work identified three separate categories of effort: Gather and organize available data on the wholesale and retail prices of gasoline at a national level for the past 5 years. Using the data collected in Subtask 1, develop models of pricing practices that aid in explaining retail markups and price differentials for different types and grades of gasoline at different retail outlets in the current gasoline market. Using the data from Subtask 1 and the analysis framework from Subtask 2, analyze the likely range of future retail markups and price differentials for different grades of leaded and unleaded gasoline. The report is organized in a format that is different than suggested by the subtasks outlined above. The first section provides a characterization of the problem - data available to quantify cost and price of the fuels as well as issues that directly affect this relationship. The second section provides a discussion of issues likely to affect this relation in the future. The third section postulates a model that can be used to quantify the relation between fuels, octane levels, costs and prices.

  6. Ballistic spin-dependent transport of Rashba rings with multi-leads

    SciTech Connect (OSTI)

    Huang Guangyao [State Key Laboratory of Optoelectronic Material and Technology and School of Physics and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Liang Shidong, E-mail: stslsd@mail.sysu.edu.cn [State Key Laboratory of Optoelectronic Material and Technology and School of Physics and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China)

    2011-05-15T23:59:59.000Z

    Research Highlights: > Transmission coefficients of each outgoing lead in multi-lead mesoscopic Rashba rings. > Spin polarizations of each outgoing lead in multi-lead mesoscopic Rashba rings. > Resonant and antiresonant conditions of spin polarization in multi-lead Rashba rings. > Symmetries of conductance and spin polarization of symmetric multi-lead Rashba rings. - Abstract: Using the Landauer-Buettiker formula with the transfer matrix technique, we develop a formalism of the ballistic spin-dependent electron transport in the multi-lead Rashba rings. We give analytic formulas of the total conductance G{sub j}, spin-{sigma} conductance g{sub j}{sup {sigma}} and spin polarization P{sub j} of each outgoing lead j, and their resonant and antiresonant conditions. Analytic studying with numerical investigating Rashba rings with several symmetric and asymmetric leads, we find that G{sub j}, g{sub j}{sup {sigma}} and P{sub j} oscillate with the incoming electron energy and the spin-orbit interaction (SOI) strength, and their antiresonances depend on the incoming electron energy, the SOI strength and the outgoing-lead angle with the incoming lead. For the symmetric-lead rings, G{sub j}, g{sub j}{sup {sigma}} and P{sub j} have some symmetries, G{sub j}=G{sub N-j},g{sub j}{sup {sigma}}=g{sub N-j}{sup -{sigma}}, and P{sub j} = -P{sub N-j} for symmetric leads, j and N - j, where the angles between the symmetric outgoing leads j and N - j and the incoming lead are {gamma}{sub N-j} = 2{pi} - {gamma}{sub j}. The spin polarization of the outgoing lead with {gamma}{sub j} = {pi} is exactly zero for even-N-symmetric-lead rings. These symmetries originate from the lead symmetry and time reversal invariance. For asymmetry-lead rings these symmetries vanish.

  7. Lead Slowing Down Spectrometer FY2013 Annual Report

    SciTech Connect (OSTI)

    Warren, Glen A.; Kulisek, Jonathan A.; Gavron, Victor A.; Danon, Yaron; Weltz, Adam; Harris, Jason; Stewart, T.

    2013-10-29T23:59:59.000Z

    Executive Summary The Lead Slowing Down Spectrometry (LSDS) project, funded by the Materials Protection And Control Technology campaign, has been evaluating the feasibility of using LSDS techniques to assay fissile isotopes in used nuclear fuel assemblies. The approach has the potential to provide considerable improvement in the assay of fissile isotopic masses in fuel assemblies compared to other non-destructive techniques in a direct and independent manner. This report is a high level summary of the progress completed in FY2013. This progress included: • Fabrication of a 4He scintillator detector to detect fast neutrons in the LSDS operating environment. Testing of the detector will be conducted in FY2014. • Design of a large area 232Th fission chamber. • Analysis using the Los Alamos National Laboratory perturbation model estimated the required number of neutrons for an LSDS measurement to be 10 to the 16th source neutrons. • Application of the algorithms developed at Pacific Northwest National Laboratory to LSDS measurement data of various fissile samples conducted in 2012. The results concluded that the 235U could be measured to 2.7% and the 239Pu could be measured to 6.3%. Significant effort is yet needed to demonstrate the applicability of these algorithms for used-fuel assemblies, but the results reported here are encouraging in demonstrating that we are making progress toward that goal. • Development and cost-analysis of a research plan for the next critical demonstration measurements. The plan suggests measurements on fresh fuel sub assemblies as a means to experimentally test self-attenuation and the use of fresh mixed-oxide fuel as a means to test simultaneous measurement of 235U and 239Pu.

  8. Chronic renal failure with gout: a marker of chronic lead poisoning

    SciTech Connect (OSTI)

    Craswell, P.W.; Price, J.; Boyle, P.D.; Heazlewood, V.J.; Baddeley, H.; Lloyd, H.M.; Thomas, B.J.; Thomas, B.W.

    1984-09-01T23:59:59.000Z

    EDTA (calcium disodium edetate) lead mobilization and x-ray fluorescence (XRF) finger bone lead tests were done in 42 patients with chronic renal failure and without persisting lead intoxication. Nineteen of 23 patients with gout and 8 of 19 without gout had positive EDTA lead mobilization tests. Those patients with gout excreted significantly more excess lead chelate than those without gout. In the gout group 17 patients denied any childhood or industrial exposure to lead. They had a greater number of positive tests and excreted significantly more excess lead chelate than 14 patients with neither gout nor lead exposure. These results confirm that gout in the presence of chronic renal failure is a useful marker of chronic lead poisoning. Of 27 patients with positive lead mobilization tests, only 13 had elevated XRF finger bone lead concentrations (sensitivity 48%). Three of 15 patients with negative lead mobilization tests had elevated XRF finger bone lead concentrations (specificity 80%). Although the XRF finger bone lead test is a convenient noninvasive addition to the diagnostic evaluation of patients with chronic renal failure and gout, its application is limited due to the lack of sensitivity of the method.

  9. Lead contamination in street soils of Nairobi City and Mombasa Island, Kenya

    SciTech Connect (OSTI)

    Onyari, J.M.; Wandiga, S.O.; Njenga, G.K.; Nyatebe, J.O. (Univ. of Nairobi (Kenya))

    1991-05-01T23:59:59.000Z

    The advent of modern industrialization and, in particular, the motor vehicle has witnessed dramatic increases in lead usage both as a component of lead-acid storage battery and from 1923 as organic lead alkyl anti-knock additive in petroleum. Several workers have established a correlation between increasing lead concentration in roadside soils and vehicular traffic density. Although researchers studied the heavy metal content in Lake Victoria sediments, no urban roadside soils were investigated. Since lead is used as a petrol additive in Kenya, it is necessary to document the extent and magnitude of lead contamination of roadside soils in inland and coastal urban environments and evaluate its environmental implications.

  10. KNN–NTK composite lead-free piezoelectric ceramic

    SciTech Connect (OSTI)

    Matsuoka, T., E-mail: ta-matsuoka@mg.ngkntk.co.jp; Kozuka, H.; Kitamura, K.; Yamada, H.; Kurahashi, T.; Yamazaki, M.; Ohbayashi, K. [NGK SPARK PLUG Co., Ltd., 2808 Iwasaki, Komaki, Aichi 485-8510 (Japan)

    2014-10-21T23:59:59.000Z

    A (K,Na)NbO{sub 3}-based lead-free piezoelectric ceramic was successfully densified. It exhibited an enhanced electromechanical coupling factor of k{sub p}?=?0.52, a piezoelectric constant d{sub 33}?=?252 pC/N, and a frequency constant N{sub p}?=?3170?Hz m because of the incorporation of an elaborate secondary phase composed primarily of KTiNbO{sub 5}. The ceramic's nominal composition was 0.92K{sub 0.42}Na{sub 0.44}Ca{sub 0.04}Li{sub 0.02}Nb{sub 0.85}O{sub 3}–0.047K{sub 0.85}Ti{sub 0.85}Nb{sub 1.15}O{sub 5}–0.023BaZrO{sub 3} –0.0017Co{sub 3}O{sub 4}–0.002Fe{sub 2}O{sub 3}–0.005ZnO, abbreviated herein as KNN–NTK composite. The KNN–NTK ceramic exhibited a dense microstructure with few microvoids which significantly degraded its piezoelectric properties. Elemental maps recorded using transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM–EDS) revealed regions of high concentrations of Co and Zn inside the NTK phase. In addition, X-ray diffraction patterns confirmed that a small portion of the NTK phase was converted into K{sub 2}(Ti,Nb,Co,Zn){sub 6}O{sub 13} or CoZnTiO{sub 4} by a possible reaction between Co and Zn solutes and the NTK phase during a programmed sintering schedule. TEM studies also clarified a distortion around the KNN/NTK interfaces. Such an NTK phase filled voids between KNN particles, resulting in an improved chemical stability of the KNN ceramic. The manufacturing process was subsequently scaled to 100?kg per batch for granulated ceramic powder using a spray-drying technique. The properties of the KNN–NTK composite ceramic produced using the scaled-up method were confirmed to be identical to those of the ceramic prepared by conventional solid-state reaction sintering. Consequently, slight changes in the NTK phase composition and the distortion around the KNN/NTK interfaces affected the KNN–NTK composite ceramic's piezoelectric characteristics.

  11. Effects of Relativity Lead to"Warp Speed" Computations

    SciTech Connect (OSTI)

    Vay, J.-L.

    2007-11-01T23:59:59.000Z

    A scientist at Lawrence Berkeley National Laboratory has discovered that a previously unnoticed consequence of Einstein's special theory of relativity can lead to speedup of computer calculations by orders of magnitude when applied to the computer modeling of a certain class of physical systems. This new finding offers the possibility of tackling some problems in a much shorter time and with far more precision than was possible before, as well as studying some configurations in every detail for the first time. The basis of Einstein's theory is the principle of relativity, which states that the laws of physics are the same for all observers, whether the 'observer' is a turtle 'racing' with a rabbit, or a beam of particles moving at near light speed. From the invariance of the laws of physics, one may be tempted to infer that the complexity of a system is independent of the motion of the observer, and consequently, a computer simulation will require the same number of mathematical operations, independently of the reference frame that is used for the calculation. Length contraction and time dilation are well known consequences of the special theory of relativity which lead to very counterintuitive effects. An alien observing human activity through a telescope in a spaceship traveling in the Vicinity of the earth near the speed of light would see everything flattened in the direction of propagation of its spaceship (for him, the earth would have the shape of a pancake), while all motions on earth would appear extremely slow, slowed almost to a standstill. Conversely, a space scientist observing the alien through a telescope based on earth would see a flattened alien almost to a standstill in a flattened spaceship. Meanwhile, an astronaut sitting in a spaceship moving at some lower velocity than the alien spaceship with regard to earth might see both the alien spaceship and the earth flattened in the same proportion and the motion unfolding in each of them at the same speed. Let us now assume that each protagonist (the alien, the space scientist and the astronaut) is to run a computer simulation describing the motion of all of them in a single calculation. In order to model a physical system on a computer, scientists often divide space and time into small chunks. Since the computer must calculated some things for each chunk, having a large system containing numerous small chunks translates to long calculations requiring many computational steps on supercomputers. Let us assume that each protagonist of our intergalactic story uses the space and time slicing as described and chooses to perform the calculation in its own frame of reference. For the alien and the space scientist, the slicing of space and time results in an exceedingly large number of chunks, due to the wide disparity of spatial and time scales needed to describe both their own environment and motion together with the other extremely flattened environment and slowed motion. Since the disparity of scales is reduced for the astronaut, who is traveling at an intermediate velocity, the number of computer operations needed to complete the calculation in his frame of reference will be significantly lower, possibly by many orders of magnitude. Analogously, the new discovery at Lawrence Berkeley National Laboratory shows that there exists a frame of reference minimizing the number of computational operations needed for studying the interaction of beams of particles or light (lasers) interacting at, or near, light speed with other particles or with surrounding structures. Speedups ranging from ten to a million times or more are predicted for the modeling of beams interacting with electron clouds, such as those in the upcoming Large Hadron Collider 'atom smasher' accelerator at CERN (Switzerland), and in free electron lasers and tabletop laser wakefield accelerators. The discovery has surprised many physicists and was received initially with much skepticism. It sounded too much like a 'free lunch'. Yet, the demonstration of a speedup of a stunning one thousand times in a te

  12. Students Lead the Way at the White House Science Fair | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Students Lead the Way at the White House Science Fair Students Lead the Way at the White House Science Fair October 18, 2010 - 6:55pm Addthis The President looks at a model solar...

  13. MODELLING THE OVERLAND TRANSPORT OF LEAD DEPOSITED FROM THE ATMOSPHERE IN THE ELBE CATCHMENT OVER FOUR

    E-Print Network [OSTI]

    Costa-Cabral, Mariza

    unknown. Despite decreasing atmospheric pollution, soil and freshwater systems still indicate high lead on minimizing atmospheric emissions, but also on minimizing soil erosion. Keywords: atmospheric pollution, direct atmospheric deposition, direct runoff, Elbe catchment, erosion, soil pollution, lead, long

  14. A Small Secure Transportable Autonomous Lead-Cooled Fast Reactor for Deployment at Remote Sites

    SciTech Connect (OSTI)

    Sienicki, J .J.; Smith, M.A.; Mosseytsev, A.V.; Yang, W.S.; Wade, D.C.

    2004-10-06T23:59:59.000Z

    This presentation discusses a small secure transportable autonomous lead-cooled fast reactor for deployment at remote sites.

  15. E-Print Network 3.0 - advanced lead-acid batteries Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Virginia Tech Collection: Computer Technologies and Information Sciences 60 Aisle Marking Requirements permanent workplace aisles should have appropriate Summary: , lead...

  16. BIOACCUMULATION OF LEAD, CALCIUM AND STRONTIUM AND THEIR RELATIONSHIPS IN THE OCTOPUS OCTOPUS VULGARIS

    E-Print Network [OSTI]

    Pierce, Graham

    BIOACCUMULATION OF LEAD, CALCIUM AND STRONTIUM AND THEIR RELATIONSHIPS IN THE OCTOPUS OCTOPUS were sampled and the concentrations of lead, calcium and strontium, in digestive gland, branchial heart the concentration of lead and those of calcium and strontium in digestive gland and a negative correlation between

  17. Lead-position dependent regular oscillations and random fluctuations of conductance in graphene quantum dots

    E-Print Network [OSTI]

    Lai, Ying-Cheng

    Lead-position dependent regular oscillations and random fluctuations of conductance in graphene.1088/0953-8984/25/8/085502 Lead-position dependent regular oscillations and random fluctuations of conductance in graphene quantum, for graphene quantum dots, the conductance variations with the lead positions. Since for graphene the types

  18. Exploration of Opportunities to Reduce Lead Times for Engineered-to-Order Products

    E-Print Network [OSTI]

    Tommelein, Iris D.

    Exploration of Opportunities to Reduce Lead Times for Engineered-to-Order Products by Jan Alarik;Abstract Exploration of Opportunities to Reduce Lead Times for Engineered-To-Order Products by Jan Alarik proposes alternative practices to improve the current process of ETO products that can lead to major

  19. Exposure to lead by the oral and the pulmonary routes of children living in the vicinity of a primary lead smelter

    SciTech Connect (OSTI)

    Roels, H.A. (Univ. of Louvain, Brussels, Belgium); Buchet, J.P.; Lauwerys, R.R.; Bruaux, P.; Claeys-Thoreau, F.; Lafontaine, A.; Verduyn, G.

    1980-06-01T23:59:59.000Z

    A medical survey was carried out among 11-year-old children attending schools situated less than 1 and 2.5 km from a lead smelter. Age-matched control children from a rural and urban area were examined at the same time. The blood lead levels (PbB) of the children living in the smelter area (mainly those attending schools located less than 1 km from the smelter) were higher than those of rural and urban children. The mean PbB levels were usually lower in girls than in boys, especially in the smelter area. Despite a slightly decreasing trend in the annual mean airborne lead concentration at less than 1 km (mean PbA: from 3.8 ..mu..g/m/sup 3/ in 1974 to 2.3 ..mu..g/m/sup 3/ in 1978) the PbB levels there did not improve, whereas 2.5 km from the plant a significant tendency to normalization of PbB became apparent. Therefore, in the third survey, the medical examination was combined with an environmental study which demonstrated that lead in school-playground dust and in air strongly correlated. Lead on the children's hands (PbH) was also significantly related to lead in air or lead in dust. Less than 1 km from the factory boys and girls had on the average 436 and 244 ..mu..g Pb/hand, respectively, vs 17.0 and 11.4 ..mu..g Pb/hand for rural boys and girls, respectively. Partial correlations between PbB, PbA, and PbH indicated that in the smelter area the quantitative contribution of PbA to the children's PbB is negligible compared to that of PbH. Thus, the control of airborne lead around the lead smelter is not sufficient to prevent excessive exposure of children to environmental lead. In view of the importance of lead transfer from dust and dirt via hands to the gastrointestinal tract remedial actions should be directed simultaneously against the atmospheric emission of lead by the smelter and against the lead particulates deposited on soil, dust, and dirt.

  20. Recommendations of treatment technologies for radioactively contaminated lead at the Idaho National Engineering Laboratory

    SciTech Connect (OSTI)

    Neupauer, R.M.; Zukauskas, J.F.

    1992-03-01T23:59:59.000Z

    Approximately one million pounds of radioactively contaminated lead are currently stored at the Idaho National Engineering Laboratory (INEL) and must be treated according to the Resource Conservation and Recovery Act. This excess lead exists in various forms, including brick, sheet, shot, wool, blankets, steel-jacketed casks, scrap, and miscellaneous solids. Several lead treatment technologies were evaluated based on effectiveness, applicability, feasibility, availability of equipment and materials, health and safety, generation of secondary waste streams, cost, and flexibility. Emphasis is given in this report to those treatment technologies that yield recyclable lead products. Methods that treat lead for storage and disposal were also investigated. Specific treatment technologies for decontaminating the excess lead at the INEL are recommended. The proposed treatment for lead brick, sheet, shot, blankets, and scrap is a series of surface decontamination techniques followed by melt-refining, if necessary. The recommended series of treatments for lead casks begins with removing and macroencapsulating the steel jackets, followed by size reducing and melt-refining the lead. Macroencapsulation is the proposed treatment for miscellaneous lead solids. Recycling lead that has been successfully decontaminated and macroencapsulating or stabilizing the treatment residuals is also recommended.

  1. E-Print Network 3.0 - alkylaminocarbene ligand leads Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Site Summary: . This leads us to believe that modeling of ligand interac- tions with bulk solvent is probably... Predicting Ligand Binding Affinity with Alchemical Free Energy...

  2. How Lead-Free Solder (Mis)Behaves under Stress | Advanced Photon...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the evolution of crystal orientation and strain patterns during thermal cycling in tin-containing, lead-free solder joints, specifically in the commonly used...

  3. U.S. Energy Secretary Chu to Lead Delegation to IAEA 54th Annual...

    Broader source: Energy.gov (indexed) [DOE]

    September 20, U.S. Energy Secretary Steven Chu will lead the American delegation at the International Atomic Energy Agency's 54th General Conference in Vienna, Austria. During...

  4. John. F. O'Leary Appointed to Lead Federal Energy Administration...

    National Nuclear Security Administration (NNSA)

    John. F. O'Leary Appointed to Lead Federal Energy Administration | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the...

  5. Should You Be Concerned about Lead in Your Home? Your children can be poisoned if they get lead in their bodies. Finding out if lead is a problem in your

    E-Print Network [OSTI]

    a small blood sample to tell if your child has lead poisoning. Ask your health-care provider about outside your home? It may have gotten there from paint on the outside of the building or from industry's hands and faces often with soap and water, especially before they eat. Wash toys every week. Keep down

  6. Blood lead concentrations in marine mammals validate estimates of 10{sup 2}- to 10{sup 3}-fold increase in human blood lead concentrations

    SciTech Connect (OSTI)

    Owen, B.D.; Flegal, A.R. [Univ. of California, Santa Cruz, CA (United States)] [Univ. of California, Santa Cruz, CA (United States)

    1998-08-01T23:59:59.000Z

    Measurements of ultra-low ambient blood lead (PbB) concentrations (mean {+-} SD = 0.13 {+-} 0.06 {micro}g/dL) in Northern elephant seals (Mirounga angustirostris) validate previous estimates of ultra-low PbB levels in preindustrial humans. These estimates had been unsubstituted, since PbB levels in this range had never been measured in any organisms prior to this study. Similarities in PbB levels among these contemporary and preindustrial mammals are consistent with similarities in their measured and estimated lead exposures, respectively. The marginally higher PbB levels and rates of lead exposure in contemporary marine mammals are, also, consistent with lead isotopic composition analyses that indicate their PbB levels have been elevated from exposure to industrial lead. Consequently, these analyses substantiate concerns that current baseline PbB levels in humans, which are estimated to be two to three orders of magnitude above natural levels, may still constitute public health risks.

  7. Sex-based differences in gene expression in hippocampus following postnatal lead exposure

    SciTech Connect (OSTI)

    Schneider, J.S., E-mail: jay.schneider@jefferson.edu; Anderson, D.W.; Sonnenahalli, H.; Vadigepalli, R.

    2011-10-15T23:59:59.000Z

    The influence of sex as an effect modifier of childhood lead poisoning has received little systematic attention. Considering the paucity of information available concerning the interactive effects of lead and sex on the brain, the current study examined the interactive effects of lead and sex on gene expression patterns in the hippocampus, a structure involved in learning and memory. Male or female rats were fed either 1500 ppm lead-containing chow or control chow for 30 days beginning at weaning.Blood lead levels were 26.7 {+-} 2.1 {mu}g/dl and 27.1 {+-} 1.7 {mu}g/dl for females and males, respectively. The expression of 175 unique genes was differentially regulated between control male and female rats. A total of 167 unique genes were differentially expressed in response to lead in either males or females. Lead exposure had a significant effect without a significant difference between male and female responses in 77 of these genes. In another set of 71 genes, there were significant differences in male vs. female response. A third set of 30 genes was differentially expressed in opposite directions in males vs. females, with the majority of genes expressed at a lower level in females than in males. Highly differentially expressed genes in males and females following lead exposure were associated with diverse biological pathways and functions. These results show that a brief exposure to lead produced significant changes in expression of a variety of genes in the hippocampus and that the response of the brain to a given lead exposure may vary depending on sex. - Highlights: > Postnatal lead exposure has a significant effect on hippocampal gene expression patterns. > At least one set of genes was affected in opposite directions in males and females. > Differentially expressed genes were associated with diverse biological pathways.

  8. BNL Building 650 lead decontamination and treatment feasibility study. Final report

    SciTech Connect (OSTI)

    Kalb, P.D.; Cowgill, M.G.; Milian, L.W. [and others

    1995-10-01T23:59:59.000Z

    Lead has been used extensively at Brookhaven National Laboratory (BNL) for radiation shielding in numerous reactor, accelerator and other research programs. A large inventory of excess lead (estimated at 410,000 kg) in many shapes and sizes is currently being stored. Due to it`s toxicity, lead and soluble lead compounds are considered hazardous waste by the Environmental Protection Agency. Through use at BNL, some of the lead has become radioactive, either by contamination of the surface or through activation by neutrons or deuterons. This study was conducted at BNL`s Environmental and Waste Technology Center for the BNL Safety and Environmental Protection Division to evaluate feasibility of various treatment options for excess lead currently being stored. The objectives of this effort included investigating potential treatment methods by conducting a review of the literature, developing a means of screening lead waste to determine the radioactive characteristics, examining the feasibility of chemical and physical decontamination technologies, and demonstrating BNL polyethylene macro-encapsulation as a means of treating hazardous or mixed waste lead for disposal. A review and evaluation of the literature indicated that a number of physical and chemical methods are available for decontamination of lead. Many of these techniques have been applied for this purpose with varying degrees of success. Methods that apply mechanical techniques are more appropriate for lead bricks and sheet which contain large smooth surfaces amenable to physical abrasion. Lead wool, turnings, and small irregularly shaped pieces would be treated more effectively by chemical decontamination techniques. Either dry abrasion or wet chemical methods result in production of a secondary mixed waste stream that requires treatment prior to disposal.

  9. Lead isotopes in sediments of the Loire River (France): natural versus anthropogenic origin

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Lead isotopes in sediments of the Loire River (France): natural versus anthropogenic origin Philippe Négrel Emmanuelle Petelet-Giraud BRGM, Orléans, France Sediments along the Loire River (central France) were investigated by means of lead isotopes determined on the labile sediment fraction, or acid

  10. Scanning tunneling spectroscopy of lead-substituted bismuth strontium copper oxide

    E-Print Network [OSTI]

    Zimmermann, Michelle (Michelle Anne)

    2007-01-01T23:59:59.000Z

    The hole-doped cuprate Bi ... is doped with lead to the solubility limit of x = 0.38 and studied using STM/STS in the overdoped regime where Tc < 2K. Despite the high lead content, residual supermodulations are observed ...

  11. Temperature Difference Leads to Magnetism | Physical Review Focus Previous Story / Volume 28 archive

    E-Print Network [OSTI]

    Wu, Junqiao

    Temperature Difference Leads to Magnetism | Physical Review Focus Previous Story / Volume 28 Leads to Magnetism J. Wu/Univ. of California, Berkeley Heat field. Heating the right edge of an n a magnetic field pointing out of the screen, according to computer simulations. Computer simulations suggest

  12. Graduate School of Education Leading, Learning, Life Changing Graduate School of Education

    E-Print Network [OSTI]

    Graduate School of Education Leading, Learning, Life Changing PSU Graduate School of Education 2010 State of the School Presentation #12;Graduate School of Education Leading, Learning, Life Changing The river lives by tributaries but also by innumerable little careful springs. #12;Graduate School

  13. Measurements with the high flux lead slowing-down spectrometer at LANL

    E-Print Network [OSTI]

    Danon, Yaron

    slow down by scattering interactions with the lead and thus enable measurements of neutron.40.Sc Keywords: Lead-slowing-down spectrometer; Lithium; Alpha; Cross section; Neutron reactions 1.elsevier.com/locate/nimb Nuclear Instruments and Methods in Physics Research B 261 (2007) 953­955 NIM BBeam Interactions

  14. Leading innovation in food, natural resources and energy Michigan State University

    E-Print Network [OSTI]

    Liu, Taosheng

    Leading innovation in food, natural resources and energy Michigan State University #12;#12;Leading innovation through collaboration AgBioResearch scientists represent six colleges at Michigan State University than 120 years, AgBioResearch (formerly the Michigan Agricultural Experiment Station or MAES) has

  15. The use of phosphorus in sequestration of lead and cadmium in a smelter slag

    SciTech Connect (OSTI)

    Lambert, M.; Pierzynski, G.; Hettiarachchi, G. [Kansas State Univ., Manhattan, KS (United States)

    1997-12-31T23:59:59.000Z

    The site of an abandoned lead smelter near the village of Dearing in southeastern Kansas is a continuing environmental and health concern because of high levels of heavy metal contamination, including lead and cadmium. Phosphate amendment of lead-contaminated soils is known to precipitate highly insoluble lead pyromorphite (Pb{sub 5}(PO{sub 4}){sub 3}Cl), effectively reducing its bioavailability. In this study, samples of Dearing slag were incubated with two different forms of soluble phosphate (apatite and potassium phosphate). Lead content of the amended slag decreased in the exchangeable, carbonate, iron- and manganese-oxide, and organic fractions of the slag, while increasing in the residual fraction. At the same time, cadmium content of the amended slag decreased in the exchangeable and iron and manganese fractions, while increasing in the carbonate and residual fractions. X-ray diffractometry shows that lead pyromorphite abundance increased in the phosphate-amended slag, suggesting that lead was precipitated as pyromorphite. Cadmium may have been precipitated as relatively insoluble octavite (CdCO{sub 3}). Of the two phosphate amendments, potassium phosphate was more effective in reducing soluble lead and cadmium, and increasing pyromorphite abundance. Also, rate effect was more important than the effect of time in remediating the slag.

  16. Guidelines for Participation in the ETV ESTE Verification Test of Lead Paint Test Kits

    E-Print Network [OSTI]

    Guidelines for Participation in the ETV ESTE Verification Test of Lead Paint Test Kits Revised 09/24/2009 The following guidelines have been set to establish the eligibility of individual test kits for participation in the ETV ESTE verification test of lead paint test kits. Test kits must conform to the following guidelines

  17. Environmental Pollution (Series B) 2 (1981) 2135 AGE-SPECIFIC LEAD DISTRIBUTION IN XYLEM RINGS

    E-Print Network [OSTI]

    Baes, Fred

    concentrations to pollution histories. INTRODUCTION The global historical record of atmospheric and environmentalEnvironmental Pollution (Series B) 2 (1981) 21­35 AGE-SPECIFIC LEAD DISTRIBUTION IN XYLEM RINGS environmental pollution records. Lead in xylem from Liriodendron tulipifera, Quercus alba, and Carya spp. trees

  18. Conversion of oil shale ash into zeolite for cadmium and lead removal from wastewater

    E-Print Network [OSTI]

    Shawabkeh, Reyad A.

    Conversion of oil shale ash into zeolite for cadmium and lead removal from wastewater Reyad; available online 29 October 2003 Abstract A by-product fly ash from oil shale processing was converted shale; Ash; Zeolite; Cadmium and lead removal 1. Introduction Oil shale exists in Jordan with large

  19. ONLINE SEIZURE DETECTION IN ADULTS WITH TEMPORAL LOBE EPILEPSY USING SINGLE-LEAD ECG

    E-Print Network [OSTI]

    ONLINE SEIZURE DETECTION IN ADULTS WITH TEMPORAL LOBE EPILEPSY USING SINGLE-LEAD ECG T. De Cooman detection using only single-lead ECG is pro- posed. It is tested on 300h of data from adults with temporal, online seizure detection, ECG, LSVM, LDA 1. INTRODUCTION Epilepsy is a neurological disorder that affects

  20. Non-Linear 12-Lead ECG Synthesis from Two Intracardiac Recordings A Kachenoura1,2

    E-Print Network [OSTI]

    Boyer, Edmond

    Non-Linear 12-Lead ECG Synthesis from Two Intracardiac Recordings A Kachenoura1,2 , F Por´ee1,2 , G-up of patients with implantable cardiac devices. To do so, two methods to synthesize 12-lead ECG from two in surface ECG. The indirect method is based on a preliminary or- thogonalization phase of ECG and EGM

  1. Short communication Real-time estimation of lead-acid battery parameters: A dynamic

    E-Print Network [OSTI]

    Ray, Asok

    -charged and over-discharged; similarly, reliable SOH estimates enhance preventive maintenance and life cycle cost situations. © 2014 Elsevier B.V. All rights reserved. 1. Introduction Lead-acid batteries provide low-costShort communication Real-time estimation of lead-acid battery parameters: A dynamic data

  2. Activated alumina adsorption of trace amounts of chromium and lead from wastewater

    E-Print Network [OSTI]

    Dennis, Reid L

    1984-01-01T23:59:59.000Z

    the concentration in the initial solution. Data for 100 90 80 70 60 %R 50 20 g/& 10 lr B rr / h. / 0. 5 u, 0. 25 g/1 , + j Pa , I f, ' / '~f/ 30 20 10 pH 10 Figure 3 ? Percent removal of lead by activated alumina for various pH values 28 100...2 for lead model Pb-2 48 15 Q vs X3 for lead model Pb-3 40 16 17 Q vs X4 for lead model Pb-4 Q vs X5 for lead model Pb-5 50 51 18 Investigation of relationship of pH for model Pb-1 54 19 Investigation of relationship of pH for model Pb-4 20...

  3. Lead Coolant Test Facility Technical and Functional Requirements, Conceptual Design, Cost and Construction Schedule

    SciTech Connect (OSTI)

    Soli T. Khericha

    2006-09-01T23:59:59.000Z

    This report presents preliminary technical and functional requirements (T&FR), thermal hydraulic design and cost estimate for a lead coolant test facility. The purpose of this small scale facility is to simulate lead coolant fast reactor (LFR) coolant flow in an open lattice geometry core using seven electrical rods and liquid lead or lead-bismuth eutectic. Based on review of current world lead or lead-bismuth test facilities and research need listed in the Generation IV Roadmap, five broad areas of requirements of basis are identified: Develop and Demonstrate Prototype Lead/Lead-Bismuth Liquid Metal Flow Loop Develop and Demonstrate Feasibility of Submerged Heat Exchanger Develop and Demonstrate Open-lattice Flow in Electrically Heated Core Develop and Demonstrate Chemistry Control Demonstrate Safe Operation and Provision for Future Testing. These five broad areas are divided into twenty-one (21) specific requirements ranging from coolant temperature to design lifetime. An overview of project engineering requirements, design requirements, QA and environmental requirements are also presented. The purpose of this T&FRs is to focus the lead fast reactor community domestically on the requirements for the next unique state of the art test facility. The facility thermal hydraulic design is based on the maximum simulated core power using seven electrical heater rods of 420 kW; average linear heat generation rate of 300 W/cm. The core inlet temperature for liquid lead or Pb/Bi eutectic is 420oC. The design includes approximately seventy-five data measurements such as pressure, temperature, and flow rates. The preliminary estimated cost of construction of the facility is $3.7M. It is also estimated that the facility will require two years to be constructed and ready for operation.

  4. Serum immunoglobulin, complement C3, and salivary IgA levels in lead workers

    SciTech Connect (OSTI)

    Ewers, U. (Univ. Dusseldorf, Germany); Stiller-Winkler, R.; Idel, H.

    1982-12-01T23:59:59.000Z

    Sera of 72 lead workers and of 53 reference subjects were examined for levels of immunoglobulins IgM, IgG, and IgA, and complement C3 by radial immunodiffusion. Salivary IgA levels were determined in 33 lead workers and 40 reference subjects. On the average the lead workers had lower serum complement C3 and immunoglobulin levels, as well as lower salivary IgA levels, than the reference subjects. A significant negative correlation was found between blood lead concentrations (PbB) and the serum levels of complement C3 and IgG in the group of lead workers, as well as in the total population examined. However, a significant positive correlation was observed between PbB and serum IgA in the group of lead workers. The results obtained in this study are discussed in relation to numerous reports in the literature showing that lead exerts adverse effects on the immune system in animals.

  5. Blood lead level association with lower body weight in NHANES 1999–2006

    SciTech Connect (OSTI)

    Scinicariello, Franco, E-mail: fes6@cdc.gov [Division of Toxicology and Human Health Sciences, Agency for Toxic Substances and Disease Registry (ATSDR), Atlanta, GA 30341 (United States); Buser, Melanie C. [Division of Toxicology and Human Health Sciences, Agency for Toxic Substances and Disease Registry (ATSDR), Atlanta, GA 30341 (United States); Mevissen, Meike [Division of Veterinary Pharmacology and Toxicology, Vetsuisse Faculty, University of Bern, 3012 Bern (Switzerland); Portier, Christopher J. [National Center for Environmental Health (NCEH)/ATSDR, CDC, Atlanta, GA 30341 (United States)

    2013-12-15T23:59:59.000Z

    Background: Lead exposure is associated with low birth-weight. The objective of this study is to determine whether lead exposure is associated with lower body weight in children, adolescents and adults. Methods: We analyzed data from NHANES 1999–2006 for participants aged ? 3 using multiple logistic and multivariate linear regression. Using age- and sex-standardized BMI Z-scores, overweight and obese children (ages 3–19) were classified by BMI ? 85th and ? 95th percentiles, respectively. The adult population (age ? 20) was classified as overweight and obese with BMI measures of 25–29.9 and ? 30, respectively. Blood lead level (BLL) was categorized by weighted quartiles. Results: Multivariate linear regressions revealed a lower BMI Z-score in children and adolescents when the highest lead quartile was compared to the lowest lead quartile (? (SE) = ? 0.33 (0.07), p < 0.001), and a decreased BMI in adults (? (SE) = ? 2.58 (0.25), p < 0.001). Multiple logistic analyses in children and adolescents found a negative association between BLL and the percentage of obese and overweight with BLL in the highest quartile compared to the lowest quartile (OR = 0.42, 95% CI: 0.30–0.59; and OR = 0.67, 95% CI: 0.52–0.88, respectively). Adults in the highest lead quartile were less likely to be obese (OR = 0.42, 95% CI: 0.35–0.50) compared to those in the lowest lead quartile. Further analyses with blood lead as restricted cubic splines, confirmed the dose-relationship between blood lead and body weight outcomes. Conclusions: BLLs are associated with lower body mass index and obesity in children, adolescents and adults. - Highlights: • NHANES analysis of BLL and body weight outcomes • Increased BLL associated with decreased body weight in children and adolescent • Increased BLL associated with decreased body weight in adults.

  6. Program to analyze the failure mode of lead-acid batteries

    SciTech Connect (OSTI)

    Zuckerbrod, D.

    1986-03-01T23:59:59.000Z

    The electrical characteristics of large lead-acid cells from nuclear power plants were studied. The overall goal was to develop nondestructive tests to predict cell failure using this easily obtained information. Cell capacitance, internal resistance, reaction resistance for hydrogen evolution and cell capacity were measured on a lead-calcium cell in good condition. A high float voltage and low internal resistance were found to correlate with good cell capacity in cells selected from a set of six lead-antimony cells in poor condition.

  7. Measurement and monitoring of tritium and other critical issues in Lead Lithium Ceramic Breeder (LLCB)

    SciTech Connect (OSTI)

    Tangri, V. K.; Mohan, S. [Heavy Water Div., Bhabha Atomic Research Centre (India); Narayanan, A.; Narayan, K. K. [Radiation Safety Systems Div., Bhabha Atomic Research Centre (India)

    2008-07-15T23:59:59.000Z

    A new Indian concept involving a lead lithium ceramic breeder is being explored. LLCB based tritium blanket modules require tritium extraction from lead-lithium as well as from helium purge gas. This paper addresses the concept of efficiency enhancement using high surface area, low-pressure drop structured gas liquid contactors for tritium extraction from the lead lithium. Conceptual flow schemes for both loops are discussed and critical issues are highlighted. Tritium monitoring systems (TMS) for measurement and monitoring of tritium is also dealt. A fast responding tritium monitor has also been developed for in situ measurement of tritium in water or gas form. It has been tested for liquid effluents. (authors)

  8. Idaho National Laboratory Lead or Lead-Bismuth Eutectic (LBE) Test Facility - R&D Requirements, Design Criteria, Design Concept, and Concept Guidance

    SciTech Connect (OSTI)

    Eric P. Loewen; Paul Demkowicz

    2005-05-01T23:59:59.000Z

    The Idaho National Laboratory Lead-Bismuth Eutectic Test Facility will advance the state of nuclear technology relative to heavy-metal coolants (primarily Pb and Pb-Bi), thereby allowing the U.S. to maintain the pre-eminent position in overseas markets and a future domestic market. The end results will be a better qualitative understanding and quantitative measure of the thermal physics and chemistry conditions in the molten metal systems for varied flow conditions (single and multiphase), flow regime transitions, heat input methods, pumping requirements for varied conditions and geometries, and corrosion performance. Furthering INL knowledge in these areas is crucial to sustaining a competitive global position. This fundamental heavy-metal research supports the National Energy Policy Development Group’s stated need for energy systems to support electrical generation.1 The project will also assist the Department of Energy in achieving goals outlined in the Nuclear Energy Research Advisory Committee Long Term Nuclear Technology Research and Development Plan,2 the Generation IV Roadmap for Lead Fast Reactor development, and Advanced Fuel Cycle Initiative research and development. This multi-unit Lead-Bismuth Eutectic Test Facility with its flexible and reconfigurable apparatus will maintain and extend the U.S. nuclear knowledge base, while educating young scientists and engineers. The uniqueness of the Lead-Bismuth Eutectic Test Facility is its integrated Pool Unit and Storage Unit. This combination will support large-scale investigation of structural and fuel cladding material compatibility issues with heavy-metal coolants, oxygen chemistry control, and thermal hydraulic physics properties. Its ability to reconfigure flow conditions and piping configurations to more accurately approximate prototypical reactor designs will provide a key resource for Lead Fast Reactor research and development. The other principal elements of the Lead-Bismuth Eutectic Test Facility (in addition to the Pool Unit and Storage Unit) are the Bench Scale Unit and Supporting Systems, principal of which are the O2 Sensor/Calibration System, Feed System, Transfer System, Off- Gas System, Purge and Evacuation System, Oxygen Sensor and Control System, Data Acquisition and Control System, and the Safety Systems. Parallel and/or independent corrosion studies and convective heat transfer experiments for cylindrical and annular geometries will support investigation of heat transfer phenomena into the secondary side. In addition, molten metal pumping concepts and power requirements will be measured for future design use.

  9. Hydrodynamic effects of leading-edge tubercles on control surfaces and in flapping foil propulsion

    E-Print Network [OSTI]

    Stanway, Michael Jordan

    2008-01-01T23:59:59.000Z

    This thesis investigates the hydrodynamic effects of biologically-inspired leading-edge tubercles. Two complementary studies examine the performance of three-dimensional hydrofoils based on the pectoral flippers of the ...

  10. Static corrosion of candidate alloys for the lead-bismuth fast reactor

    E-Print Network [OSTI]

    Wang, Yunzhi (Yunzhi Diana)

    2008-01-01T23:59:59.000Z

    This project examined the corrosion rates and mechanisms of two candidate alloys for use in Lead-bismuth Eutectic (LBE) cooled fast nuclear reactors. The two alloys examined were T91 and Fe-12Cr-2Si. An experimental study ...

  11. NREL's Gearbox Reliability Collaborative leads to wind turbine gearbox reliability, lowering the cost of energy.

    E-Print Network [OSTI]

    NREL's Gearbox Reliability Collaborative leads to wind turbine gearbox reliability, lowering operations. In 2007, the National Renewable Energy Laboratory (NREL) initi- ated the Gearbox Reliability that contribute to reduced gearbox reliability. In contrast to private investigations of these problems, GRC

  12. Tuition and Fees Your education is an investment that can lead to new professional opportunities, personal

    E-Print Network [OSTI]

    Vertes, Akos

    Tuition and Fees Your education is an investment that can lead to new professional opportunities,485 per credit hour*** Cost of books is not included in the course tuition. Specific details

  13. E-Print Network 3.0 - america brazil leads Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    China's deliveries to USA jumped by 50%, Brazil equally strong, and Indonesia gains markets... in Germany and the UK Profiled wood imports run steady, the US is the leading...

  14. An evaluation of inductance loop detector lead length and optimal speed trap distance

    E-Print Network [OSTI]

    Hamm, Robert Alan

    1994-01-01T23:59:59.000Z

    . Lead lengths were evaluated with five different design vehicles (large and small passenger cars, a pickup truck, a motorcycle, and a high profile truck) with several detector units. Both passenger cars and the pickup truck were always detected with 4000...

  15. New Jersey firm creates jobs and vital components for world-leading...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Jersey firm creates jobs and vital components for world-leading experiment By John Greenwald July 10, 2012 Tweet Widget Google Plus One Share on Facebook This superconducting wire...

  16. Characterization of cardiac lead perforation risk via a dynamic simulated environment

    E-Print Network [OSTI]

    Rosario, Matthew J

    2012-01-01T23:59:59.000Z

    Delayed cardiac perforation is a serious medical condition where an implanted cardiac lead migrates through the heart wall, causing life-threatening complications. Where acute perforation occurs during implant, delayed ...

  17. Understanding sensitization behavior of lead selenide photoconductive detectors by charge separation model

    SciTech Connect (OSTI)

    Zhao, Lihua, E-mail: lihua.zhao@ou.edu, E-mail: shi@ou.edu; Qiu, Jijun; Weng, Binbin; Chang, Caleb; Yuan, Zijian; Shi, Zhisheng, E-mail: lihua.zhao@ou.edu, E-mail: shi@ou.edu [School of Electrical and Computer Engineering, University of Oklahoma, Norman, Oklahoma 73019 (United States)

    2014-02-28T23:59:59.000Z

    We introduce a charge separation model in this work to explain the mechanism of enhanced photoconductivity of polycrystalline lead salt photoconductors. Our results show that this model could clarify the heuristic fabrication processes of such lead salt detectors that were not well understood and often considered mysterious for nearly a century. The improved lifetime and performance of the device, e.g., responsivity, are attributed to the spatial separation of holes and electrons, hence less possibility of carrier recombination. This model shows that in addition to crystal quality the size of crystallites, the depth of outer conversion layer, and doping concentration could all affect detector performance. The simulation results agree well with experimental results and thus offer a very useful tool for further improvement of lead salt detectors. The model was developed with lead salt family of photoconductors in mind, but may well be applicable to a wider class of semiconducting films.

  18. anti-fas antibodies leads: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 21 LEAD POISONING PREVENTION INFORMATION Environmental Sciences and Ecology Websites Summary:...

  19. Sol-gel preparation of lead magnesium niobate (PMN) powders and thin films

    DOE Patents [OSTI]

    Boyle, T.J.

    1999-01-12T23:59:59.000Z

    A method of preparing a lead magnesium niobium oxide (PMN), Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}, precursor solution by a solvent method wherein a liquid solution of a lead-complex PMN precursor is combined with a liquid solution of a niobium-complex PMN precursor, the combined lead- and niobium-complex liquid solutions are reacted with a magnesium-alkyl solution, forming a PMN precursor solution and a lead-based precipitate, and the precipitate is separated from the reacted liquid PMN precursor solution to form a precipitate-free PMN precursor solution. This precursor solution can be processed to form both ferroelectric powders and thin films. 3 figs.

  20. Sol-Gel Preparation Of Lead Magnesium Ni Obate (Pmn) Powdersand Thin Films

    DOE Patents [OSTI]

    Boyle, Timothy J. (Albuquerque, NM)

    1999-01-12T23:59:59.000Z

    A method of preparing a lead magnesium niobium oxide (PMN), Pb(Mg.sub.1/3 Nb.sub.2/3)O.sub.3, precursor solution by a solvent method wherein a liquid solution of a lead-complex PMN precursor is combined with a liquid solution of a niobium-complex PMN precursor, the combined lead- and niobium-complex liquid solutions are reacted with a magnesium-alkyl solution, forming a PMN precursor solution and a lead-based precipitate, and the precipitate is separated from the reacted liquid PMN precursor solution to form a precipitate-free PMN precursor solution. This precursor solution can be processed to form both ferroelectric powders and thin films.

  1. Optimization of actinide transmutation in innovative lead-cooled fast reactors

    E-Print Network [OSTI]

    Romano, Antonino, 1972-

    2003-01-01T23:59:59.000Z

    The thesis investigates the potential of fertile free fast lead-cooled modular reactors as efficient incinerators of plutonium and minor actinides (MAs) for application to dedicated fuel cycles for transmutation. A methodology ...

  2. Blockage of IL-6 secretion in glia by lead and mercury

    E-Print Network [OSTI]

    Pourrajabi, Nima Matthew

    2003-01-01T23:59:59.000Z

    Mercury (Hg) and lead (Pb) are toxic to the development and function of the central nervous system (CNS). Interleukin-6 (IL 6) produced by astroglia protects neurons from damage in many progressive degenerative disorders. IL-6 secretion...

  3. Lead Test Assembly Irradiation and Analysis Watts Bar Nuclear Plant, Tennessee and Hanford Site, Richland, Washington

    Broader source: Energy.gov [DOE]

    This EA evaluates the environmental impacts associated with the U.S. Department of Energy proposed action to conduct a lead test assembly program to confirm the viability of using a commercial...

  4. Determination of particulate lead using aerosol mass spectrometry: MILAGRO/MCMA-2006 observations

    E-Print Network [OSTI]

    Salcedo, D.

    We report the first measurements of particulate lead (Pb) from Aerodyne Aerosol Mass Spectrometers, which were deployed in and around Mexico City during the Megacity Initiative: Local and Global Research Observations ...

  5. Fullerenes Buckminster Fullerenes ("Buckyballs") have fascinated chemists since the original discovery of C60, leading

    E-Print Network [OSTI]

    Weston, Ken

    discovery of C60, leading to the 1996 Nobel Prize in Chemistry for Curl, Kroto, and Smalley. Although metal ion, such as titanium, zirconium, or uranium directly from carbon vapor. The resulting M@C28

  6. Design of passive decay heat removal system for the lead cooled flexible conversion ratio fast reactor

    E-Print Network [OSTI]

    Whitman, Joshua (Joshua J.)

    2007-01-01T23:59:59.000Z

    The lead-cooled flexible conversion ratio fast reactor shows many benefits over other fast-reactor designs; however, the higher power rating and denser primary coolant present difficulties for the design of a passive decay ...

  7. Boundary element simulation of oscillating foil with leading-edge separation

    E-Print Network [OSTI]

    Dong, Xiaoxia, S.M. Massachusetts Institute of Technology

    2007-01-01T23:59:59.000Z

    In this thesis, we develop a numerical model to account for the leading-edge separation for the boundary element simulation of the oscillating foil with potential flow assumption. Similar to the trailing-edge separation, ...

  8. CBER-DETR Nevada Coincident and Leading Employment Benchmark Revisions Add Employment to Nevada

    E-Print Network [OSTI]

    Ahmad, Sajjad

    Statistics. The Nevada Coincident EmploymentCBER-DETR Nevada Coincident and Leading Employment Indexes1 Benchmark Revisions Add Employment to Nevada The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using

  9. Strategy for reducing the length and variability of aircraft lead time

    E-Print Network [OSTI]

    Bielat, Brendon (Brendon Michael)

    2010-01-01T23:59:59.000Z

    Helicopter manufacturers typically build each aircraft to order, and the lead time for make or buy parts and assemblies can be several months or more. The manufacturers generally have a backlog of orders at any given time, ...

  10. Helium and lead isotope geochemistry of oceanic volcanic rocks from the East Pacific and South Atlantic

    E-Print Network [OSTI]

    Graham, David W. (David William)

    1987-01-01T23:59:59.000Z

    The isotopic evolution of helium and lead in the Earth is coupled by virtue of their common radioactive parents uranium and thorium. The isotopic signatures in oceanic volcanic rocks provide constraints on the temporal ...

  11. Next-to-leading order slepton pair production at hadron colliders

    E-Print Network [OSTI]

    Howard Baer; B. W. Harris; Mary Hall Reno

    1997-12-09T23:59:59.000Z

    We compute total cross sections for various slepton pair production reactions in next-to-leading order QCD. For pbarp collisions at root S=2TeV, we find leading order cross sections to be enhanced by typically 35% to 40%. For pp collisions at root S=14TeV, the enhancement ranges from 25% to 35% depending on the mass of the sleptons. We comment upon the phenomenological implications of these results.

  12. A study of the reaction between lead (II) iodide and organic amine hydriodides

    E-Print Network [OSTI]

    Simpson, Frank Martin

    1962-01-01T23:59:59.000Z

    for the degree of NASTER OF SCIENCE AUGUST 1962 Major Sub)cot& CHENISTRY A STUDY OF THE REACTION BETWEEN LEAD(II) IODIDE AND ORGANIC AMINE HYDRIODIDES A Thesis By FRANK MARTIN SIMPSON Approved as to style and content by: Chai of Committee Head... compounds have been prepared by the reaction of lead(II) iodide with various primary, secondary, and tertiary aliphatic and substituted aromati. c amines The melting points, chemical compositions, densities, quali- tative solubilities, and absorption...

  13. Pb nanowire formation on Al/lead zirconate titanate surfaces in high-pressure hydrogen

    SciTech Connect (OSTI)

    Alvine, Kyle J.; Shutthanandan, V.; Arey, Bruce W.; Wang, Chong M.; Bennett, Wendy D.; Pitman, Stan G.

    2012-07-12T23:59:59.000Z

    Thin films of Al on lead zirconate titanate (PZT) annealed in high-pressure hydrogen at 100C exhibit surface Pb nanowire growth. Wire diameter is approximately 80 nm and length can exceed 100 microns. Based on microstructural analysis using electron microscopy and ion scattering, a vapor-solid scheme with hydrogen as a carrier gas was proposed as a growth mechanism. We expect that these observations may lead to controlled Pb nanowires growth through pattering of the Al film.

  14. Non-lead, environmentally safe projectiles and method of making same

    DOE Patents [OSTI]

    Lowden, Richard A. (Clinton, TN); McCoig, Thomas M. (Maryville, TN); Dooley, Joseph B. (Harriman, TN)

    2000-01-01T23:59:59.000Z

    A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic phase material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics.

  15. Affordability analysis of lead emission controls for a smelter-refinery. Final report

    SciTech Connect (OSTI)

    Scherer, T.M.

    1989-10-01T23:59:59.000Z

    This document evaluates the affordability and economic impact of additional control measures deemed necessary for a smelter-refinery to meet the lead emission standard. The emphasis in the analysis is on the impact of control costs on the smelter-refinery's profitability. The analysis was performed using control-cost data from two different lead-smelter studies in conjunction with other existing industry data.

  16. Blood and hair lead in children with different extents of iron deficiency in Karachi

    SciTech Connect (OSTI)

    Ataur Rahman, Muhammad; Rahman, Bushra [Karachi Institute of Biotechnology and Genetic Engineering, University of Karachi, Karachi-75270 (Pakistan)] [Karachi Institute of Biotechnology and Genetic Engineering, University of Karachi, Karachi-75270 (Pakistan); Saeed Ahmad, Muhammad [School of Healthcare Science, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom)] [School of Healthcare Science, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom); Blann, Andrew [Department of Medicine, City Hospital, Birmingham B18 7QH, United Kingdom. (United Kingdom)] [Department of Medicine, City Hospital, Birmingham B18 7QH, United Kingdom. (United Kingdom); Ahmed, Nessar, E-mail: N.Ahmed@mmu.ac.uk [School of Healthcare Science, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom)] [School of Healthcare Science, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom)

    2012-10-15T23:59:59.000Z

    Childhood iron deficiency has a high incidence in Pakistan. Some but not all studies have shown that dietary iron deficiency may cause increased absorption of lead as both compete for the same transporters in the small intestine. Therefore, children in Pakistan, residing in heavily polluted cities like Karachi may be prone to lead poisoning. This hypothesis was tested by investigating blood and hair lead concentrations in children from Karachi who were divided into four groups of iron status; normal, borderline iron deficiency, iron deficiency and iron deficiency anaemia. A prospective observational study was conducted where 269 children were categorized into four groups of iron status using the World Health Organization criteria and one based on soluble transferrin receptor measurements. Blood iron status was determined using a full blood count, serum iron, ferritin, transferrin saturation and soluble transferrin receptor measurements. Blood lead was determined by graphite atomic absorption spectroscopy, whereas hair lead was assessed using an inductively coupled plasma atomic emission spectroscopy technique. Blood lead concentrations were significantly higher in children with iron deficiency anaemia (mean [95% confidence intervals] were 24.9 [22.6-27.2] {mu}g/dL) compared to those with normal iron status (19.1 [16.8-21.4] {mu}g/dL) using WHO criteria. In contrast, hair lead content was not significantly different in children of different iron status. Our findings reinforce the importance of not only reducing environmental lead pollution but also the development of national health strategies to reduce childhood iron deficiency in Pakistan.

  17. Comparison of bioturbation rates determined by lead-210 and plutonium in abyssal cores

    E-Print Network [OSTI]

    Stordal, Mary Christine

    1981-01-01T23:59:59.000Z

    COMPARISON OF BIOTURBATION RATES DETERMINED BY LEAD-210 AND PLUTONIUM IN ABYSSAI. CORES A Thesis by MARY CHRISTINE STORDAL Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree... of MASTER OF SCIENCE December 1981 Major Subject: Oceanography COMPARISON OF BIOTURBATION RATES DETERMINED BY LEAD-210 AND PLUTONIUM IN ABYSSAL CORES A Thesis MARY CHRISTINE STORDAL Approved as t. o style and content by: (Chairman of Committee...

  18. A measurement of E/{pi} for a fast lead liquid argon calorimeter

    SciTech Connect (OSTI)

    Makowiecki, D.; Gordon, H.A.; Ma, H.; Murtagh, M.; Radeka, V.; Rahm, D.; Rescia, S. [Brookhaven National Lab., Upton, NY (United States); Abrams, G.S.; Groom, D.E.; Kirsten, F.; Levi, M.; Siegrist, J. [Lawrence Berkeley Lab., CA (United States); Amako, K.; Inaba, O.; Kondo, T. [National Lab. for High Energy Physics, Tsukuba, Ibaraki (Japan); Baden, A.R.; Fong, D.; Hadley, N.; Kunori, S.; Skuja, A. [Maryland Univ., College Park, MD (United States); Bowen, T.; Forden, G.; Jenkins, E.; Johns, K.; Rutherfoord, J.; Shupe, M. [Arizona Univ., Tucson, AZ (United States); Burnett, T.; Cook, V.; Davisson, R.; Mockett, P.; Rothberg, J.; Williams, R.W. [Washington Univ., Seattle, WA (United States); Cremaldi, L.; Reidy, J.; Summers, D. [Mississippi Univ., University, MS (United States); DiGiacomo, N. [Martin Marietta Aerospace, Denver, CO (United States). Astronautics Group; Draper, P.; Ferbel, T.; Lobkowicz, F. [Rochester Univ., NY (United States); Faust, J.; Hauptman, J.; Pang, M. [Iowa State Univ. of Science and Technology, Ames, IA (United States); Gabriel, T.A. [Oak Ridge National Lab., TN (United States); Hagopian, V.; Womersley, J. [Florida State Univ., Tallahassee, FL (United States); Handler, T. [Tennessee Univ., Knoxville, TN (United States); Hitlin, D. [California Inst. of Tech., Pasadena, CA (United States); Mulholland, G.T. [Fermi National Accelerator Lab., Batavia, IL (United States); Watanabe, Y. [Tokyo Inst. of Tech. (Japan); Weerts, H. [Michigan State Univ., East Lansing, MI (United States)

    1990-12-31T23:59:59.000Z

    The NA34 (HELIOS) calorimeter has measured e/{pi} {congruent} 1.1 in a uranium/liquid argon calorimeter with a shaping time of 135 nsec. Lead may be a viable alternative, but e/{pi} must first be measured at fast shaping times in lead. We re preparing to measure e/{pi} at momenta ranging from 0.5 to 20 GeV/c and with shaping times of 50, 100 and 150 nsec.

  19. A measurement of E/. pi. for a fast lead liquid argon calorimeter

    SciTech Connect (OSTI)

    Makowiecki, D.; Gordon, H.A.; Ma, H.; Murtagh, M.; Radeka, V.; Rahm, D.; Rescia, S. (Brookhaven National Lab., Upton, NY (United States)); Abrams, G.S.; Groom, D.E.; Kirsten, F.; Levi, M.; Siegrist, J. (Lawrence Berkeley Lab., CA (United States)); Amako, K.; Inaba, O.; Kondo, T. (National Lab. for High Energy Physics, Tsukuba, Ibaraki (Japan)); Baden, A.R.; Fong, D.; Hadley, N.; Kunori, S.; Skuja, A. (Maryland U

    1990-01-01T23:59:59.000Z

    The NA34 (HELIOS) calorimeter has measured e/{pi} {congruent} 1.1 in a uranium/liquid argon calorimeter with a shaping time of 135 nsec. Lead may be a viable alternative, but e/{pi} must first be measured at fast shaping times in lead. We re preparing to measure e/{pi} at momenta ranging from 0.5 to 20 GeV/c and with shaping times of 50, 100 and 150 nsec.

  20. Radiation Damage of F8 Lead Glass with 20 MeV Electrons

    E-Print Network [OSTI]

    Schaefer, B D; McChesney, P; Shepherd, M R; Frye, J M

    2011-01-01T23:59:59.000Z

    Using a 20 MeV linear accelerator, we investigate the effects of electromagnetic radiation on the optical transparency of F8 lead glass. Specifically, we measure the change in attenuation length as a function of radiation dose. Comparing our results to similar work that utilized a proton beam, we conclude that F8 lead glass is more susceptible to proton damage than electron damage.

  1. Leading Edge Flow Structure of a Dynamically Pitching NACA 0012 Airfoil

    E-Print Network [OSTI]

    Pruski, Brandon

    2012-11-27T23:59:59.000Z

    LEADING EDGE FLOW STRUCTURE OF A DYNAMICALLY PITCHING NACA 0012 AIRFOIL A Thesis by BRANDON JAMES PRUSKI Submitted to the O ce of Graduate Studies of Texas A&M University in partial ful llment of the requirements for the degree of MASTER... OF SCIENCE Approved by: Chair of Committee, Rodney Bowersox Committee Members, Helen Reed Simon North Head of Department, Rodney Bowersox December 2012 Major Subject: Aerospace Engineering Copyright 2012 Brandon James Pruski ABSTRACT The leading edge...

  2. Design of an Actinide Burning, Lead or Lead-Bismuth Cooled Reactor that Produces Low Cost Electricity FY-01 Annual Report, October 2001

    SciTech Connect (OSTI)

    Mac Donald, Philip Elsworth; Buongiorno, Jacopo; Davis, Cliff Bybee; Herring, James Stephen; Loewen, Eric Paul; Smolik, Galen Richard; Weaver, Kevan Dean; Todreas, N.

    2001-10-01T23:59:59.000Z

    The purpose of this collaborative Idaho National Engineering and Environmental Laboratory (INEEL) and Massachusetts Institute of Technology (MIT) Laboratory Directed Research and Development (LDRD) project is to investigate the suitability of lead or lead-bismuth cooled fast reactors for producing low-cost electricity as well as for actinide burning. The goal is to identify and analyze the key technical issues in core neutronics, materials, thermal-hydraulics, fuels, and economics associated with the development of this reactor concept. Work has been accomplished in four major areas of research: core neutronic design, plant engineering, material compatibility studies, and coolant activation. The publications derived from work on this project (since project inception) are listed in Appendix A.

  3. Design of an Actinide Burning, Lead or Lead-Bismuth Cooled Reactor That Produces Low Cost Electricty - FY-02 Annual Report

    SciTech Connect (OSTI)

    Mac Donald, Philip Elsworth; Buongiorno, Jacopo

    2002-10-01T23:59:59.000Z

    The purpose of this collaborative Idaho National Engineering and Environmental Laboratory (INEEL) and Massachusetts Institute of Technology (MIT) Laboratory Directed Research and Development (LDRD) project is to investigate the suitability of lead or lead-bismuth cooled fast reactors for producing low-cost electricity as well as for actinide burning. The goal is to identify and analyze the key technical issues in core neutronics, materials, thermal-hydraulics, fuels, and economics associated with the development of this reactor concept. Work has been accomplished in four major areas of research: core neutronic design, plant engineering, material compatibility studies, and coolant activation. The publications derived from work on this project (since project inception) are listed in Appendix A. This is the third in a series of Annual Reports for this project, the others are also listed in Appendix A as FY-00 and FY-01 Annual Reports.

  4. Experiments Performed in Substantiation of the Conditioning of BN-350 Spent Cesium Traps Using Lead or Lead-Bismuth Alloy Filling Technology

    SciTech Connect (OSTI)

    O. Romanenko; I. Tazhibaeva; I. Yakovlev; A. Ivanov; D. Wells; A. Herrick; J. Michelbacher; S. Shiganakov

    2009-05-01T23:59:59.000Z

    The technology of cleaning cesium radionuclides from sodium coolant at the BN-350 fast reactor was realized in the form of cesium traps of two types: stationary devices connected to the circuit that was to be cleaned and in-core devices installed into the core of reactor when it was not under operation. Carbon-graphite materials were used as sorbents to collect and concentrate radioactive cesium, accumulated in the BN-350 reactor circuits over the decades of their operation, in relatively small volume traps which provided effective radiation-safe conditions for personnel working in proximity to the coolant and equipment of the primary circuit during BN-350 decommissioning. Spent cesium traps, as products unfit for further use, represent solid radioactive wastes. The presence of chemically active sodium, potassium and cesium that are able to react violently with water results in series of problems related to their disposal in the Republic of Kazakhstan. Considering the technology of filling spent cesium traps with lead/lead-bismuth alloy as a priority one for their conditioning, evaluations for safety substantiation were implemented. A set of experiments was implemented aimed at verification of calculations performed in substantiation of the proposed technology: filling a full scale cesium trap mock-up with sodium followed by its draining to determine the optimal regimes of draining; filling bench scale cesium trap mock-ups with sodium and cesium followed by sodium draining and filling with lead or lead-bismuth alloy at different temperatures and filling rates to chose the optimal regimes for filling spent cesium traps; implementation of leachability tests to determine the rate of cesium release from the filling materials into water. This paper provides a description of the experimental program carried out and the main results obtained.

  5. Lead iodide X-ray and gamma-ray spectrometers for room and high temperature operation

    SciTech Connect (OSTI)

    Hermon, H.; James, R.B.; Lund, J. [Sandia National Labs., Livermore, CA (United States)] [and others

    1998-12-31T23:59:59.000Z

    In this study the authors report on the results of the investigation of lead iodide material properties. The effectiveness of a zone refining purification method on the material purity is determined by ICP-MS and ICP-OES and correlated to the electrical and physical material properties. They show that this zone refining method is very efficient in removing impurities from lead iodide, and they also determine the segregation coefficient for some of these impurities. Triple axis X-ray diffraction (TAD) analysis has been used to determine the crystalline perfection of the lead iodide after applying various cutting, etching and fabrication methods. The soft lead iodide crystal was found to be damaged when cleaved by a razor blade, but by using a diamond wheel saw, followed by etching, the crystallinity of the material was much improved, as observed by TAD. Low temperature photoluminescence also indicates an improvement in the material properties of the purified lead iodide. Electrical properties of lead iodide such as carrier mobility, were calculated based on carrier-phonon scattering. The results for the electrical properties were in good agreement with the experimental data.

  6. Lead iodide X-ray and gamma-ray spectrometers for room and high temperature operation

    SciTech Connect (OSTI)

    Hermon, H.; James, R.B.; Cross, E. [and others

    1997-02-01T23:59:59.000Z

    In this study, we report on the results of the investigation of lead iodide material properties. The effectiveness of zone refining purification methods on the material purity is determined by ICP-MS and ICP-OES and correlated to the electrical and physical material properties. We show that this zone refining method is very efficient in removing impurities from lead iodide and we also determine the segregation coefficient for some of these impurities. Triple axis x- ray diffraction (TAD) analysis has been used to determine the crystalline perfection of the lead iodide after applying various cutting, etching, and fabrication methods. The soft lead iodide crystal was found to be damaged when cleaved by a razor blade, but by using a diamond wheel saw, followed by etching, the crystallinity of the material was improved, as observed by TAD. Low temperature photoluminescence also indicates an improvement in the material properties of the purified lead iodide. Electrical properties of lead iodide such as carrier mobility, were calculated based on carrier- phonon scattering. The results for the electrical properties were in good agreement with the experimental data.

  7. Lead iron phosphate glass as a containment medium for disposal of high-level nuclear waste

    DOE Patents [OSTI]

    Boatner, Lynn A. (Oak Ridge, TN); Sales, Brian C. (Oak Ridge, TN)

    1989-01-01T23:59:59.000Z

    Lead-iron phosphate glasses containing a high level of Fe.sub.2 O.sub.3 for use as a storage medium for high-level radioactive nuclear waste. By combining lead-iron phosphate glass with various types of simulated high-level nuclear waste, a highly corrosion resistant, homogeneous, easily processed glass can be formed. For corroding solutions at 90.degree. C., with solution pH values in the range between 5 and 9, the corrosion rate of the lead-iron phosphate nuclear waste glass is at least 10.sup.2 to 10.sup.3 times lower than the corrosion rate of a comparable borosilicate nuclear waste glass. The presence of Fe.sub.2 O.sub.3 in forming the lead-iron phosphate glass is critical. Lead-iron phosphate nuclear waste glass can be prepared at temperatures as low as 800.degree. C., since they exhibit very low melt viscosities in the 800.degree. to 1050.degree. C. temperature range. These waste-loaded glasses do not readily devitrify at temperatures as high as 550.degree. C. and are not adversely affected by large doses of gamma radiation in H.sub.2 O at 135.degree. C. The lead-iron phosphate waste glasses can be prepared with minimal modification of the technology developed for processing borosilicate glass nuclear wasteforms.

  8. AVTA: Plug-In Hybrid Electric Vehicles

    Broader source: Energy.gov [DOE]

    2013 Ford Fusion Energi2013 Ford C-Max Energi Fleet2013 Ford C-Max Energi2012 Chevrolet Volt2012 Toyota Prius2013 Toyota Prius2013 Chevrolet Volt2011 Chrysler Town & Country2010 Quantum...

  9. Integration of the predictions of two models with dose measurements in a case study of children exposed to the emissions of a lead smelter

    E-Print Network [OSTI]

    Bonnard, R.

    2010-01-01T23:59:59.000Z

    methodology to a lead smelter site, Human and Ecologicala case study of the RSR lead smelter Superfund site. Journaldust, and proximity to lead smelters. Pediatrics Luo Y, Yang

  10. Assessment of circuit board surface finishes for electronic assembly with lead-free solders

    SciTech Connect (OSTI)

    Ray, U.; Artaki, I.; Finley, D.W.; Wenger, G.M. [Bell Labs., Princeton, NJ (United States). Lucent Technologies; Pan, T.; Blair, H.D.; Nicholson, J.M. [Ford Motor Co., Dearborn, MI (United States); Vianco, P.T. [Sandia National Labs., Albuquerque, NM (United States)

    1996-10-01T23:59:59.000Z

    The suitability of various metallic printed wiring board surface finishes was assessed for new technology applications that incorporate assembly with Lead-free solders. The manufacture of a lead-free product necessitates elimination of lead (Pb) from the solder, the circuit board as well as the component lead termination. It is critical however for the selected interconnect Pb-free solder and the corresponding printed wiring board (PWB) and component lead finishes to be mutually compatible. Baseline compatibility of select Pb-free solders with Pb containing PWB surface finish and components was assessed. This was followed by examining the compatibility of the commercially available CASTIN{trademark} (SnAgCuSb) Pb-free solder with a series of PWB metallic finishes: Ni/Au, Ni/Pd, and Pd/Cu. The compatibility was assessed with respect to assembly performance, solder joint integrity and long term attachment reliability. Solder joint integrity and mechanical behavior of representative 50 mil pitch 20I/O SOICs was determined before and after thermal stress. Mechanical pull test studies demonstrated that the strength of SnAgCuSb solder interconnections is notably greater than that of SnPb interconnections.

  11. Characteristics of lead induced stress corrosion cracking of alloy 690 in high temperature

    SciTech Connect (OSTI)

    Chung, K.K. [Korea Inst. of Nuclear Safety, Taejon (Korea, Republic of); Lim, J.K. [Chonbuk National Univ., Chonju (Korea, Republic of); Watanabe, Yutaka; Shoji, Tetsuo [Tohoku Univ., Sendai (Japan). Research Inst. for Fracture Technology

    1996-10-01T23:59:59.000Z

    Slow strain rate tests (SSRT) were conducted on alloy 690 in various lead chloride solutions and metal lead added to 100 ppm chloride solution at 288 C. The corrosion potential (rest potential) for the alloy was measured with SSRT tests. The cracking was observed by metallographic examination and electron probe micro analyzer. Also, the corrosion behavior of the alloy was evaluated by anodic polarized measurement at 30 C. Resulting from the tests, cracking was characterized by cracking behavior, crack length and crack growth rate, and lead effects on cracking. The cracking was mainly intergranular in mode, approximately from 60 um to 450 um in crack length, and approximately 10{sup {minus}6} to 10{sup {minus}7} mmS-1 in crack velocity. The cracking was evaluated through the variation the corrosion potential in potential-time and lead behavior during SSRTs. The lead effect in corrosion was evaluated through active to passive transition behavior in anodic polarized curves. The corrosion reactions in the cracking region were confirmed by electron probe microanalysis. Alloy 690 is used for steam generation tubes in pressurized water reactors.

  12. Overview of recent studies related to lead-alloy-cooled fast reactors

    SciTech Connect (OSTI)

    Takahashi, Minoru; Sa, Rongyuan; Pramutadi, Asril; Yamaki-Irisawa, Eriko [Research Laboratory for Nuclear Reactors, Tokyo Institute of Technology, N1-18, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8550 (Japan); Department of Nuclear Engineering, Tokyo Institute of Technology, N1-18, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8550 (Japan); Solutions Research Laboratory, Tokyo Institute of Technology, S8-11, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8550 (Japan)

    2012-06-06T23:59:59.000Z

    The recent progress of the studies related to lead alloy-cooled reactors (LFR) and the accelerator driven system (ADS) is summarized. The compatibility of materials with lead alloys has been clarified under steady and transient temperature conditions. Higher Cr content, Si and Al addition and Al-Fe alloy-coating improved the corrosion resistance of steels. The Al-Fe alloy-coated steel was not corroded even under high temperature transient conditions. The ceramics of SiC and Si{sub 3}N{sub 4} are expected to be used as cladding material for high temperature LFR. For the analytical consideration of mass transport in lead alloy circuit, the diffusion coefficient of Ni was measured using the capillary methods. A new bubble visualization method in LBE using gamma-ray radiography was developed. The thermal interaction of lead-bismuth eutectic (LBE) and lead droplets with sub-cooled water, and the behaviors of droplet fragmentation were investigated, and the visualization of volatile liquids in high temperature liquids was achieved.

  13. E-Print Network 3.0 - advanced hybrid imaging Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Prius Used ... Source: North Carolina State University, North Carolina Solar Center Collection: Renewable Energy ; Energy Storage, Conversion and Utilization 2...

  14. Lead Emissions from the Use of Leaded Aviation Gasoline in the United States: Technical Support Document (EPA420-R-08-020)

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartmentNationalRestart of the Review of theOFFICEACMEFUTURE MOBILITYMarchUnitedrLead

  15. Retrofit wall system for insulation and lead encasement in older multi-family housing.

    SciTech Connect (OSTI)

    Wendt, R. L.

    1998-08-11T23:59:59.000Z

    This paper presents an approach to modernization or rehabilitation of buildings with uninsulated masonry walls that have lead-based paint hazards or deteriorated plaster walls. The approach provides a solution to lead contamination on the walls, increased energy efficiency and comfort improvements associated with better insulated building envelopes. The system sheaths or replaces damaged or contaminated walls with a tight, well-insulated, durable interior surface. The costs of this system are estimated to be less than those of other insulated wall systems. Modeling of the impact of this system shows significant improvement in energy performance. The energy savings over the life of this durable system contribute to significantly offset the often-times sizeable cost of lead hazard remediation.

  16. Composite materials with metal oxide attached to lead chalcogenide nanocrystal quantum dots with linkers

    DOE Patents [OSTI]

    Fuke, Nobuhiro; Koposov, Alexey Y; Sykora, Milan; Hoch, Laura

    2014-12-16T23:59:59.000Z

    Composite materials useful for devices such as photoelectrochemical solar cells include a substrate, a metal oxide film on the substrate, nanocrystalline quantum dots (NQDs) of lead sulfide, lead selenide, and lead telluride, and linkers that attach the NQDs to the metal oxide film. Suitable linkers preserve the 1s absorption peak of the NQDs. A suitable linker has a general structure A-B-C where A is a chemical group adapted for binding to a MO.sub.x and C is a chemical group adapted for binding to a NQD and B is a divalent, rigid, or semi-rigid organic spacer moiety. Other linkers that preserve the 1s absorption peak may also be used.

  17. Measurement of Leading Neutron Production in Deep-Inelastic Scattering at HERA

    E-Print Network [OSTI]

    H1 Collaboration

    2010-01-04T23:59:59.000Z

    The production of leading neutrons, where the neutron carries a large fraction x_L of the incoming proton's longitudinal momentum, is studied in deep-inelastic positron-proton scattering at HERA. The data were taken with the H1 detector in the years 2006 and 2007 and correspond to an integrated luminosity of 122 pb^{-1}. The semi-inclusive cross section is measured in the phase space defined by the photon virtuality 6 neutron transverse momentum p_T neutron structure function, F_2^{LN(3)}(Q^2,x,x_L), and the fraction of deep-inelastic scattering events containing a leading neutron are studied as a function of Q^2, x and x_L. Assuming that the pion exchange mechanism dominates leading neutron production, the data provide constraints on the shape of the pion structure function.

  18. Primary lead smelter, Doe Run, Herculaneum, Missouri: Volume 2 -- Appendix B.1. Final report

    SciTech Connect (OSTI)

    Phoenix, F.J.

    1999-08-01T23:59:59.000Z

    The United States Environmental Protection Agency`s (EPA) Emission Standards Division (ESD) is investigating the primary lead smelting source category to identify and quantify organic hazardous air pollutants (HAPs) emitted from blast furnaces. The primary objective was to obtain data on the emissions of volatile and semi-volatile organic HAPs, aldehydes, and ketones from primary lead smelter blast furnaces. A secondary objective was to obtain data on the emissions of carbon monoxide. The data will be used by ESD to determine whether organic HAPs are emitted at levels that would justify regulation under the Maximum Achievable Control Technology (MACT) program. The Doe Run Company, which operates a primary lead smelter in Herculaneum, Missouri was selected by the ESD as the host facility for this project. This volume consists of Appendix B.1.

  19. Primary lead smelter, Doe Run, Herculaneum, Missouri: Volume 1 -- Text and Appendix A. Final report

    SciTech Connect (OSTI)

    Phoenix, F.J.

    1999-08-01T23:59:59.000Z

    The United States Environmental Protection Agency`s (EPA) Emission Standards Division (ESD) is investigating the primary lead smelting source category to identify and quantify organic hazardous air pollutants (HAPs) emitted from blast furnaces. The primary objective was to obtain data on the emissions of volatile and semi-volatile organic HAPs, aldehydes, and ketones from primary lead smelter blast furnaces. A secondary objective was to obtain data on the emissions of carbon monoxide. The data will be used by ESD to determine whether organic HAPs are emitted at levels that would justify regulation under the Maximum Achievable Control Technology (MACT) program. The Doe Run Company, which operates a primary lead smelter in Herculaneum, Missouri was selected by the ESD as the host facility for this project. This volume consists of the report text and Appendix A.

  20. Isotopic generator for bismuth-212 and lead-212 based on radium

    DOE Patents [OSTI]

    Hines, J.J.; Atcher, R.W.; Friedman, A.M.

    1985-01-30T23:59:59.000Z

    Disclosed are method and apparatus for providing radionuclides of bismuth-212 and lead-212. Thorium-228 and carrier solution starting material is input to a radiologically contained portion of an isotopic generator system, and radium-224 is separated from thorium-228 which is retained by a strongly basic anion exchange column. The separated radium-224 is transferred to an accessible, strongly acidic cationic exchange column. The cationic column retains the radium-224, and natural radioactive decay generates bismuth-212 and lead-212. The cationic exchange column can also be separated from the contained portion of the system and utilized without the extraordinary safety measures necessary in the contained portion. Furthermore, the cationic exchange column provides over a relatively long time period the short lived lead-212 and bismuth-212 radionuclides which are useful for a variety of medical therapies.

  1. Charged-Higgs-boson production at the LHC: Next-to-leading-order supersymmetric QCD corrections

    SciTech Connect (OSTI)

    Dittmaier, Stefan; Kraemer, Michael; Spira, Michael; Walser, Manuel [Physikalisches Institut, Albert-Ludwigs-Universitaet Freiburg, D-79104 Freiburg (Germany); Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut), Foehringer Ring 6, D-80805 Muenchen (Germany); Institute for Theoretical Particle Physics and Cosmology, RWTH Aachen University, D-52056 Aachen (Germany); Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Institute for Theoretical Physics, ETH Zuerich, CH-8093 Zuerich (Switzerland)

    2011-03-01T23:59:59.000Z

    The dominant production process for heavy charged-Higgs bosons at the LHC is the associated production with heavy quarks. We have calculated the next-to-leading-order supersymmetric QCD corrections to charged-Higgs production through the parton processes qq,gg{yields}tbH{sup {+-}} and present results for total cross sections and differential distributions. The QCD corrections reduce the renormalization and factorization scale dependence and thus stabilize the theoretical predictions. We present a comparison of the next-to-leading-order results for the inclusive cross section with a calculation based on bottom-gluon fusion gb{yields}tH{sup {+-}} and discuss the impact of the next-to-leading-order corrections on charged-Higgs searches at the LHC.

  2. MEASUREMENT OF THE SHOCK-HEATED MELT CURVE OF LEAD USING PYROMETRY AND REFLECTOMETRY

    SciTech Connect (OSTI)

    D. Partouche-Sebban and J. L. Pelissier, Commissariat a` l'Energie Atomique,; F. G. Abeyta, Los Alamos National Laboratory; W. W. Anderson, Los Alamos National Laboratory; M. E. Byers, Los Alamos National Laboratory; D. Dennis-Koller, Los Alamos National Laboratory; J. S. Esparza, Los Alamos National Laboratory; S. D. Borror, Bechtel Nevada; C. A. Kruschwitz, Bechtel Nevada

    2004-01-01T23:59:59.000Z

    Data on the high-pressure melting temperatures of metals is of great interest in several fields of physics including geophysics. Measuring melt curves is difficult but can be performed in static experiments (with laser-heated diamond-anvil cells for instance) or dynamically (i.e., using shock experiments). However, at the present time, both experimental and theoretical results for the melt curve of lead are at too much variance to be considered definitive. As a result, we decided to perform a series of shock experiments designed to provide a measurement of the melt curve of lead up to about 50 GPa in pressure. At the same time, we developed and fielded a new reflectivity diagnostic, using it to make measurements on tin. The results show that the melt curve of lead is somewhat higher than the one previously obtained with static compression and heating techniques.

  3. Dexterity test data contribute to reduction in leaded glovebox gloves use

    SciTech Connect (OSTI)

    Cournoyer, Michael E [Los Alamos National Laboratory; Lawton, Cindy M [Los Alamos National Laboratory; Castro, Amanda M [Los Alamos National Laboratory; Costigan, Stephen A [Los Alamos National Laboratory; Schreiber, Stephen [Los Alamos National Laboratory

    2009-01-01T23:59:59.000Z

    Programmatic operations at the Los Alamos National Laboratory Plutonium Facility (T A-55) involve working with various amounts of plutonium and other highly toxic, alpha-emitting materials. The spread of radiological contamination on surfaces, airborne contamination, and excursions of contaminants into the operator's breathing zone are prevented through the use of a variety of gloveboxes. Using an integrated approach, controls have been developed and implemented through an efficient Glovebox Glove Integrity Program. A key element of this program is to consider measures that lower the overall risk of glovebox operations. Line management who own glovebox processes through this program make decisions on which type of glovebox gloves (hereafter referred to as gloves), the weakest component of this safety-significant system, would perform best in these aggressive environments. As Low as Reasonably Achievable considerations must be balanced with glove durability and worker dexterity, both of which affect the final overall risk of the operation. In the past, lead-loaded (leaded) gloves made from Hypalon(reg.) were the primary glove for programmatic operations at TA55. Replacing leaded gloves with unleaded gloves for certain operations would lower the overall risk as well as reduce the amount of mixed transuranic waste. This effort contributes to the Los Alamos National Laboratory Continuous Improvement Program by improving the efficiency, cost-effectiveness, and formality of glovebox operations. In this report, the pros and cons of wearing leaded gloves, the effect of leaded gloves versus unleaded gloves on task performance using standard dexterity tests, the justification for switching from leaded to unleaded gloves, and the pollution prevention benefits of this dramatic change in the glovebox system are presented.

  4. Dexterity tests data contribute to reduction in leaded glovebox gloves use

    SciTech Connect (OSTI)

    Cournoyer, Michael E [Los Alamos National Laboratory; Lawton, Cindy M [Los Alamos National Laboratory; Castro, Amanda M [Los Alamos National Laboratory

    2008-01-01T23:59:59.000Z

    Programmatic operations at the Los Alamos National Laboratory Plutonium Facility (TA-55) involve working with various amounts of plutonium and other highly toxic, alphaemitting materials. The spread of radiological contamination on surfaces and airborne contamination and excursions of contaminants into the operator's breathing zone are prevented through the use of a variety of gloveboxes. Through an integrated approach, controls have been developed and implemented through an efficient Glovebox Glove Integrity Program (GGJP). A key element of this program is to consider measures that lower the overall risk of glovebox operations. Line management owning glovebox processes through this program make decisions on which type of glovebox gloves (the weakest component of this safety significant system) would perform in these aggressive environments. As Low As Reasonably Achievable (ALARA) considerations must be balanced with glove durability and worker dexterity, both of which affect the final overall risk of the operation. In the past, lead-loaded (leaded) glovebox gloves made from Hypalon(reg.) had been the workhorse of programmatic operations at TA-55. Replacing leaded gloves with unleaded gloves for certain operations would lower the overall risk as well as reduced the amount of mixed TRU waste. This effort contributes to Los Alamos National Laboratory Continuous Improvement Program by improving the efficiency, cost effectiveness, and formality of glovebox operations. In the following report, the pros and cons of wearing leaded glovebox gloves, the effect of leaded gloves versus unleaded gloves on task performance using standard dexterity tests, the justification for switching from leaded to unleaded gloves, and pollution prevention benefits of this dramatic change in the glovebox system are presented.

  5. Successful application of lead isotopes in source apportionment, legal proceedings, remediation and monitoring

    SciTech Connect (OSTI)

    Gulson, Brian, E-mail: brian.gulson@mq.edu.au [Graduate School of the Environment, Faculty of Science, Macquarie University, Sydney, NSW 2109 (Australia) [Graduate School of the Environment, Faculty of Science, Macquarie University, Sydney, NSW 2109 (Australia); CSIRO Earth Science and Resource Engineering North Ryde, NSW 1670 (Australia); Korsch, Michael [CSIRO Earth Science and Resource Engineering North Ryde, NSW 1670 (Australia)] [CSIRO Earth Science and Resource Engineering North Ryde, NSW 1670 (Australia); Winchester, Wayne; Devenish, Matthew; Hobbs, Thad [Esperance Cleanup and Recovery Project, Western Australia (WA) Department of Transport, Esperance 6450 (Australia)] [Esperance Cleanup and Recovery Project, Western Australia (WA) Department of Transport, Esperance 6450 (Australia); Main, Cleve; Smith, Gerard [Animal Health Laboratory, Department of Agriculture and Food, Perth 6151, WA (Australia)] [Animal Health Laboratory, Department of Agriculture and Food, Perth 6151, WA (Australia); Rosman, Kevin; Howearth, Lynette; Burn-Nunes, Laurie [Curtin University, Department of Imaging and Applied Physics, Bentley 6102, WA (Australia)] [Curtin University, Department of Imaging and Applied Physics, Bentley 6102, WA (Australia); Seow, Jimmy; Oxford, Cameron [Department of Environment and Conservation, Booragoon 6154, WA (Australia)] [Department of Environment and Conservation, Booragoon 6154, WA (Australia); Yun, Gracie; Gillam, Lindsay [Department of Health, East Perth 6004, WA (Australia)] [Department of Health, East Perth 6004, WA (Australia); Crisp, Michelle [LED (Locals for Esperance Development), Esperance 6450, WA (Australia)] [LED (Locals for Esperance Development), Esperance 6450, WA (Australia)

    2012-01-15T23:59:59.000Z

    In late 2006, the seaside community in Esperance Western Australia was alerted to thousands of native bird species dying. The source of the lead (Pb) was determined by Pb isotopes to derive from the handling of Pb carbonate concentrate through the Port, which began in July 2005. Concern was expressed for the impact of this on the community. Our objectives were to employ Pb isotope ratios to evaluate the source of Pb in environmental samples for use in legal proceedings, and for use in remediation and monitoring. Isotope measurements were undertaken of bird livers, plants, drinking water, soil, harbour sediments, air, bulk ceiling dust, gutter sludge, surface swabs and blood. The unique lead isotopic signature of the contaminating Pb carbonate enabled diagnostic apportionment of lead in samples. Apart from some soil and water samples, the proportion of contaminating Pb was >95% in the environmental samples. Lead isotopes were critical in resolving legal proceedings, are being used in the remediation of premises, were used in monitoring of workers involved in the decontamination of the storage facility, and monitoring transport of the concentrate through another port facility. Air samples show the continued presence of contaminant Pb, more than one year after shipping of concentrate ceased, probably arising from dust resuspension. Brief details of the comprehensive testing and cleanup of the Esperance community are provided along with the role of the Community. Lead isotopic analyses can provide significant benefits to regulatory agencies, interested parties, and the community where the signature is able to be characterised with a high degree of certainty. - Highlights: Black-Right-Pointing-Triangle Lead carbonate concentrate. Black-Right-Pointing-Triangle Successful use of Pb isotopes in identifying sources of Pb arising from transport and shipping. Black-Right-Pointing-Triangle Use of Pb isotopes in legal proceedings and their use in cleanup of residences. Black-Right-Pointing-Triangle Use of Pb isotopes in cleanup of a residual 9000 tonnes of Pb carbonate and in ongoing monitoring.

  6. An evaluation of chemical screening test kits for lead in paint

    SciTech Connect (OSTI)

    Oglesby, L.S.

    1996-04-01T23:59:59.000Z

    The Residential Lead-Based Paint Hazard Reduction Act (Title X) requires abatement and management of lead-based paint. The purpose of this study was to evaluate three chemical screening test kits using materials and methods from one study and subjecting the results to the statistical analysis of another. The three kits were used to predict the presence of lead in paint at ten weight concentrations from 0.04 to 3.97%. Paint was applied to four wood boards yielding a sample size of 40. Four boards were painted with lead-free paint and used as blanks. All of the boards were tested with the three test kits by an untrained individual having no knowledge of the actual lead content. Sensitivity, specificity, and false positive and negative rates were calculated for the test kit results. The manufactures` detection limits, the observed sensitivity ranged from 1.00 to 0.80, specificity ranged from 1.00 to 0.42, false positive ranged from 0 to 58%, and false negatives ranged from 0 to 20%. At the 0.5% Federal threshold level, the observed sensitivity ranged from 1.00 to 0.94, specificity ranged from 1.00 to 0.5, false positives ranged from 0 to 11.1%, and false negatives ranged from 0 to 20%. The observed false positive and false negative rates for all three kits were found to be significantly lower than those reported in a previous study. These results indicate that the kits perform very well at the Federal threshold, with two of the kits having false negative rates below 12.5% and false positive rates of 3.13%. These results indicate that these two kits would probably be acceptable screening tests for lead in paint.

  7. Lead and chromium concentrations in the potable water of the Eastern Province of Saudi Arabia

    SciTech Connect (OSTI)

    Hassan, H.M.A.; Mustafa, H.T.; Rihan, T.I. (King Faisal Univ., Dammam (Saudi Arabia))

    1989-10-01T23:59:59.000Z

    The World Health Organization (WHO) and United States Public Health Service (USPHS) standards for drinking water recommend an upper limit concentration of 0.05 mg/L for both lead and chromium. The authors studied the cadmium and zinc concentrations in the potable water of the Eastern Province of the Kingdom of Saudi Arabia. They report here the results of the study of lead and chromium concentrations in the potable water of the same area to provide a more complete profile of the levels of heavy metals in the potable water of the Eastern Province.

  8. Analysis of lead-acid battery deep-cycle accelerated testing data

    SciTech Connect (OSTI)

    Clifford, J.E.; Thomas, R.E.

    1984-06-01T23:59:59.000Z

    Battelle conducted a detailed analysis of the deep cycle, accelerated test data (at a nominal 70 C) obtained by Exide in the three-year, Phase I program to develop advanced lead-acid batteries for utility load leveling. Cycle life results for 60 lead-acid cells in three fractional factorial experiments were analyzed to develop quantitative relationships for real-time cycles to failure as a function of cell design variables. Important factors affecting cycle life were depth of discharge with respect to plate active material and acid within the plate stack, acid specific gravity, separator system design, and additives in the active material.

  9. Computational study: Reduction of iron corrosion in lead coolant of fast nuclear reactor

    SciTech Connect (OSTI)

    Arkundato, Artoto; Su'ud, Zaki; Abdullah, Mikrajuddin; Widayani [Physics Department, ITB, Bandung (Indonesia) and Physics Department, University of Jember, Jl. Kalimantan III/25, Jember (Indonesia); Physics Department, ITB Jl. Ganesha 10, Bandung (Indonesia)

    2012-06-20T23:59:59.000Z

    In this paper we report molecular dynamics simulation results of iron (cladding) corrosion in interaction with lead coolant of fast nuclear reactor. The goal of this work is to study effect of oxygen injection to the coolant to reduce iron corrosion. By evaluating diffusion coefficients, radial distribution functions, mean-square displacement curves and observation of crystal structure of iron before and after oxygen injection, we concluded that a significant reduction of corrosion can be achieved by issuing about 2% of oxygen atoms into lead coolant.

  10. The effects of a jet on vortex breakdown over a sharp leading-edge delta wing

    E-Print Network [OSTI]

    Maynard, Ian Kenneth

    2012-06-07T23:59:59.000Z

    THE EFFECTS OF A JET ON VORTEX BREAKDOWN OVER A SHARP LEADING-EDGE DELTA WING A Thesis Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE December 1985... Major Subject: Aerospace Engineering THE EFFECTS OF A JET ON VORTEX BREAKDOWN OVER A SHARP LEADING-EDGE DELTA WING A Thesis by IAN KENNETH MAYNARD Approved as to style and content by: Cyrus Ostowar (Chairman of Committee) Stan J Miley (M er...

  11. Long-term mortality profile of heavily-exposed lead smelter workers

    SciTech Connect (OSTI)

    McMichael, A.J. (South Australian Health Commission, Adelaide); Johnson, H.M.

    1982-05-01T23:59:59.000Z

    Of 241 male smelter workers diagnosed as having lead poisoning during 1928 to 1959, 140 are known to have subsequently died. Their cause-of-death profile has been compared with that of 695 other male decedents (predominantly nonoffice production workers) from the same smelter and with that of the Australian male population. Age-standarized proportional mortality analysis shows a substantial excess in the numbers of deaths from chronic renal disease and cerebral hemorrhage, particularly prior to 1965. A moderate excess was also apparent for the other smelter workers. In recent years, these mortality excesses in lead-exposed workers have largely dissipated.

  12. Non-lead, environmentally safe projectiles and method of making same

    DOE Patents [OSTI]

    Lowden, R.A.; McCoig, T.M.; Dooley, J.B.

    1998-06-02T23:59:59.000Z

    A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic phase material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics. 7 figs.

  13. Lead-free precussion primer mixes based on metastable interstitial composite (MIC) technology

    DOE Patents [OSTI]

    Dixon, George P. (Alexandria, VA); Martin, Joe A. (Espanola, NM); Thompson, Don (Ridgecrest, CA)

    1998-01-01T23:59:59.000Z

    A lead-free percussion primer composition and a percussion cup containing e composition. The lead-free percussion primer composition is comprised of a mixture of about 45 wt % aluminum powder having an outer coating of aluminum oxide and molybdenum trioxide powder or a mixture of about 50 wt % aluminum powder having an outer coating of aluminum oxide and polytetrafluoroethylene powder. The aluminum powder, molybdenum trioxide powder and polytetrafluoroethylene powder has a particle size of 0.1 .mu.m or less, more preferably a particle size of from about 200-500 angstroms.

  14. Nuclear dynamics in the EMC effect at Next-to-Next-to-Leading order

    E-Print Network [OSTI]

    S. Atashbar Tehrani; H. Mouji

    2014-03-22T23:59:59.000Z

    We study in details the parameterizations of the nuclear parton distributions at the next-to-next-to-leading order (NNLO) of $\\alpha_s$. In low $x$ and $Q_0^2$, we observe negative gluon distribution at this order which signals the saturation condition or the quark-gluon plasma condition. Our study also shows the gluon distribution at (NNLO) is less than next-to-leading order (NLO) of $\\alpha_s$, and the sea quark distribution at (NNLO) is larger than (NLO).

  15. Soil and Water Science Department University of Florida Environmental impacts of lead pellets at shooting ranges and arsenical herbicides

    E-Print Network [OSTI]

    Ma, Lena

    Soil and Water Science Department University of Florida Environmental impacts of lead pellets 4/1999-3/2002 Objectives: · Evaluate the environmental impacts of lead pellets at shooting ranges

  16. COMPARISON OF LEAD CONCENTRATION IN SURFACE SOIL BY INDUCTED COUPLED PLASMA/OPTICAL EMISSION SPECTROMETRY AND X-RAY FLUORESCENCE

    E-Print Network [OSTI]

    Boyer, Edmond

    , where a secondary lead smelter had been operating for a long time, was investigated. The objective, since a secondary lead smelter had been operating for a long time in the village and some contaminated

  17. Stroke Research at USC South Carolina's midlands area leads the world in the number of strokes.

    E-Print Network [OSTI]

    Almor, Amit

    Stroke Research at USC South Carolina's midlands area leads the world in the number of strokes stroke. At the University of South Carolina, a team of investigators is working towards understanding the effect of stroke on everyday life. Much of this research is focused on communication, something which

  18. Statistical physics of cerebral embolization leading to stroke J. P. Hague1

    E-Print Network [OSTI]

    Hague, Jim

    Statistical physics of cerebral embolization leading to stroke J. P. Hague1 and E. M. L. Chung2 1 stroke using a minimal model of emboli moving through the cerebral arteries. Our model of the blood flow stroke to be a feature of the cerebral blood flow network on the verge of a phase transition. DOI: 10

  19. Keeping the lead: How to strengthen shark conservation and management policies in Canada

    E-Print Network [OSTI]

    Myers, Ransom A.

    Keeping the lead: How to strengthen shark conservation and management policies in Canada Aurelie, Canada B3H 4J1 b WWF-Canada, Halifax, Nova Scotia, Canada B3J 1P3 a r t i c l e i n f o Article history: Biodiversity conservation Bycatch Canada Fisheries management Sharks Threatened species a b s t r a c

  20. Indoor Air Quality Poor indoor air quality comes from many sources. It can lead to having

    E-Print Network [OSTI]

    Indoor Air Quality Fact Sheet Poor indoor air quality comes from many sources. It can lead Indoor Air Pollutants · Molds · Pollen · Dander from pet fur · Secondhand smoke · Formaldehyde · Carbon monoxide that comes from burning propane, other gases and fuels, and charcoal · Household products

  1. A Mathematical Model of the Lead-Acid Battery to Address the Effect of Corrosion

    E-Print Network [OSTI]

    Subramanian, Venkat

    A Mathematical Model of the Lead-Acid Battery to Address the Effect of Corrosion Vijayasekaran for the corrosion process that occurs at the interface between the active material and grid material of the positive plate. Three different modeling approaches are used to incorporate the effect of corrosion in the first

  2. Influences of water chemistry on the acute toxicity of lead to Pimephales promelas and Ceriodaphnia dubia

    E-Print Network [OSTI]

    Grosell, Martin

    Influences of water chemistry on the acute toxicity of lead to Pimephales promelas and Ceriodaphnia in gasoline and from Pb-based paints. Although such applications were phased out beginning in the 1970s to natural variability in receiving water chemistry that can differentially impact its chemical speciation

  3. Neural Computation 9, 971983 (1997) Physiological Gain Leads to High ISI Variability in

    E-Print Network [OSTI]

    Columbia University

    Neural Computation 9, 971­983 (1997) Physiological Gain Leads to High ISI Variability in a Simple@phy.ucsf.edu, ken@phy.ucsf.edu Abstract To understand the interspike interval (ISI) variability displayed by visual that have previously been proposed. When ISI's are dominated by post­spike recovery, 1= p N arguments hold

  4. MINNESOTA LEADERS IN FOOD AND HEALTH Minnesota Research: Leading the Way

    E-Print Network [OSTI]

    Minnesota, University of

    :40-11:00 BREAK 11:00-11:30 "Bee Health: Why Should We Care?" MARLA SPIVAK, Ph MINNESOTA LEADERS IN FOOD AND HEALTH Minnesota Research: Leading and Challenges for Food and Health Research: Directions of the USDA Extramural Grant

  5. Code for prompt numerical computation of the leading order GPD evolution

    E-Print Network [OSTI]

    A. V. Vinnikov

    2006-04-27T23:59:59.000Z

    This paper describes the design and work of a set of computer routines capable for numerical computation of generalized parton distributions (GPDs) evolution at the leading order. The main intention of this work is to present a fast-working computer code making possible fitting of GPDs parameters to the data on hard electron-nucleon scattering.

  6. Enhancement of thermoelectric figure-of-merit by resonant states of aluminium doping in lead selenide

    E-Print Network [OSTI]

    Zhang, Qinyong

    By adding aluminium (Al) into lead selenide (PbSe), we successfully prepared n-type PbSe thermoelectric materials with a figure-of-merit (ZT) of 1.3 at 850 K. Such a high ZT is achieved by a combination of high Seebeck ...

  7. Open charm production in deep inelastic scattering at next-to-leading order at HERA

    E-Print Network [OSTI]

    B. W. Harris

    1999-09-09T23:59:59.000Z

    An introduction and overview of charm production in deep inelastic scattering at HERA is given. The existing next-to-leading order perturbative QCD calculations are then reviewed, and key results are summarized. Finally, comparisons are made with the most recent HERA data, and unresolved issues are highlighted.

  8. Photoproduction of jets at HERA in next-to-leading order QCD

    E-Print Network [OSTI]

    B. W. Harris; J. F. Owens

    1997-04-14T23:59:59.000Z

    A new next-to-leading order Monte Carlo program for the calculation of jet cross sections in photoproduction is described. The contributions from both resolved and direct components are included to O(\\alpha \\alpha_s^2). Properties of the predictions for various inclusive jet and dijet observables are discussed and comparisons with HERA data are presented.

  9. Modeling Coulombic failure of sea ice with leads Alexander V. Wilchinsky1

    E-Print Network [OSTI]

    Feltham, Daniel

    Modeling Coulombic failure of sea ice with leads Alexander V. Wilchinsky1 and Daniel L. Feltham1 ice failure under lowconfinement compression is modeled with a linear Coulombic criterion that can of anisotropy we consider a simplified anisotropic sea ice model where the sea ice thickness depends

  10. Efficient methylammonium lead iodide perovskite solar cells with active layers from 300 to 900 nm

    SciTech Connect (OSTI)

    Momblona, C.; Malinkiewicz, O.; Soriano, A.; Gil-Escrig, L.; Bandiello, E.; Scheepers, M.; Bolink, H. J., E-mail: henk.bolink@uv.es [Instituto de Ciencia Molecular, Universidad de Valencia, C/Catedrático J. Beltrán 2, 46980 Paterna, Valencia (Spain); Roldán-Carmona, C. [Instituto de Ciencia Molecular, Universidad de Valencia, C/Catedrático J. Beltrán 2, 46980 Paterna, Valencia (Spain); Department of Physical Chemistry and Applied Thermodynamics, University of Córdoba, Campus Rabanales, Ed. C3, 14014, Córdoba (Spain); Edri, E. [Department of Materials and Interfaces, Weizmann Institute of Science, Herzl St. 34, Rehovot 76100 (Israel)

    2014-08-01T23:59:59.000Z

    Efficient methylammonium lead iodide perovskite-based solar cells have been prepared in which the perovskite layer is sandwiched in between two organic charge transporting layers that block holes and electrons, respectively. This configuration leads to stable and reproducible devices that do not suffer from strong hysteresis effects and when optimized lead to efficiencies close to 15%. The perovskite layer is formed by using a dual-source thermal evaporation method, whereas the organic layers are processed from solution. The dual-source thermal evaporation method leads to smooth films and allows for high precision thickness variations. Devices were prepared with perovskite layer thicknesses ranging from 160 to 900 nm. The short-circuit current observed for these devices increased with increasing perovskite layer thickness. The main parameter that decreases with increasing perovskite layer thickness is the fill factor and as a result optimum device performance is obtained for perovskite layer thickness around 300 nm. However, here we demonstrate that with a slightly oxidized electron blocking layer the fill factor for the solar cells with a perovskite layer thickness of 900 nm increases to the same values as for the devices with thin perovskite layers. As a result the power conversion efficiencies for the cells with 300 and 900 nm are very similar, 12.7% and 12%, respectively.

  11. Federal Service Student Ambassador Aisha Hasan, UMCP Unstoppable Starts Here: Born to Lead,

    E-Print Network [OSTI]

    Anisimov, Mikhail

    Federal Service Student Ambassador Aisha Hasan, UMCP 1 Unstoppable Starts Here: Born to Lead Act within the states and territories of America! Hi, my name is Aisha Hasan and I am a senior as the #12;Federal Service Student Ambassador Aisha Hasan, UMCP 2 liaison between the federal government

  12. Kaolinite and Lead in Saturated Porous Media: Facilitated and Impeded Transport

    E-Print Network [OSTI]

    Ma, Lena

    of contaminants in the media. Lead Pb is a toxic heavy metal commonly found in the en- vironment. Recent studies-facilitated contaminant transport in saturated porous media. A clay colloid kaolinite and a heavy-metal contaminant Pb models; Water treatment; Water pollution; Experimentation. Author keywords: Colloid; Colloid

  13. Leading-order hadronic contributions to the electron and tau anomalous magnetic moments

    E-Print Network [OSTI]

    Florian Burger; Grit Hotzel; Karl Jansen; Marcus Petschlies

    2015-01-21T23:59:59.000Z

    The leading hadronic contributions to the anomalous magnetic moments of the electron and the $\\tau$-lepton are determined by a four-flavour lattice QCD computation with twisted mass fermions. The continuum limit is taken and systematic uncertainties are quantified. Full agreement with results obtained by phenomenological analyses is found.

  14. Superfund state-lead remedial project-management handbook. Final report

    SciTech Connect (OSTI)

    Winter, B.

    1986-12-01T23:59:59.000Z

    The handbook defines the roles and responsibilities of the Remedial Project Officer (RPM) with regard to State-lead remedial projects at uncontrolled hazardous-waste sites. It also discusses project-management techniques and the resources available to the RPM for accomplishing his mission.

  15. Superfund federal-lead remedial project-management handbook. Final report

    SciTech Connect (OSTI)

    Hooper, S.

    1986-12-01T23:59:59.000Z

    The handbook defines the roles and responsibilities of the Remedial Project Officer (RPM) with regard to Federal-lead remedial projects at uncontrolled hazardous-waste sites. It also discusses project management techniques and the resources available to the RPM for accomplishing his mission.

  16. Gate-Dependent Carrier Diffusion Length in Lead Selenide Quantum Dot Field-Effect Transistors

    E-Print Network [OSTI]

    Yu, Dong

    -generation solar panels. Strongly confined QDs such as lead selenide (PbSe) also have the potential to benefit from- generation photovoltaic devices and sensitive photodetec- tors.1-3 The potential for low fabrication cost improvements are still necessary for QD solar cells to compete with commercial technologies. In particular

  17. Mutation Causing Self-Aggregation in Human C-Crystallin Leading to Congenital Cataract

    E-Print Network [OSTI]

    Srinivasan, N.

    Mutation Causing Self-Aggregation in Human C-Crystallin Leading to Congenital Cataract Venu Talla,1 of congenital hereditary cataract are as- sociated with mutations in the crystallin genes. The authors focus attention on congenital lamellar cataract, which is asso- ciated with the R168W mutation in C

  18. ENERGY MODELING OF A LEAD-ACID BATTERY WITHIN HYBRID WIND / PHOTOVOLTAIC SYSTEMS

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    ENERGY MODELING OF A LEAD-ACID BATTERY WITHIN HYBRID WIND / PHOTOVOLTAIC SYSTEMS O. GERGAUD, G Abstract: Within the scope of full-scale energy modeling of a hybrid wind / photovoltaic system coupled-power hybrid wind/photovoltaic production system (20 ASE modules for a 2- kW polycrystalline silicon peak

  19. DFTand k.p modellingof the phase transitions of lead and tin halideperovskites for photovoltaic cells

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    DFTand k.p modellingof the phase transitions of lead and tin halideperovskites for photovoltaic Rennes, UMR 6226, 35042 Rennes, France KeywordsPerovskite, photovoltaic, first-principles calculations, k these hybrid semiconductor photovoltaic cells(HSPC) maydiffer from the one of dye-sensitized solar cells (DSSC

  20. Lead Fishing Weights and Other Fishing Tackle in Selected Waterbirds J. CHRISTIAN FRANSON

    E-Print Network [OSTI]

    345 Lead Fishing Weights and Other Fishing Tackle in Selected Waterbirds J. CHRISTIAN FRANSON 1 Institute, 411 Route 1, Suite 1, Falmouth, ME 04105 USA 4 Arizona Cooperative Fish and Wildlife Research address: Vermont Cooperative Fish and Wildlife Research Unit, University of Vermont 328 Aiken Center

  1. Quadratic voltage profiles in lead acid cells during slow, steady processes

    E-Print Network [OSTI]

    Haaser, Robert Anthony

    1999-01-01T23:59:59.000Z

    It is standard lore that the voltage profile varies linearly in space within the electrolyte of a lead acid cell under slow, steady discharge. However, this hypothesis has never been put to the test. A recent theory predicts a uniform, non...

  2. Test of English as a Foreign LanguageTM Leading. www.ets.org/toefl

    E-Print Network [OSTI]

    Test of English as a Foreign LanguageTM Listening. Learning. Leading. www.ets.org/toefl Information Internet-based testing ONLY. Information about TOEFL computer-based testing,TOEFL paper-based testing, and the Test of Spoken English is in a separate Bulletin. Read all of the information in this Bulletin

  3. Effect of taurine on chemoshock seizure thresholds in lead-exposed animals

    SciTech Connect (OSTI)

    Huxtable, R.J.; Shindo, S.; Nakagawa, K.

    1986-03-01T23:59:59.000Z

    The high levels of taurine found in developing brain have led to postulates that taurine is involved in brain maturation. The authors have examined the effect of taurine on the chemoshock threshold of rats reared in the presence of the environmental toxin, lead. Within 24 h of giving birth, dams were placed on one of four regimens: Group P received 0.4% lead acetate in the drinking water; Group T received 3% taurine in drinking water; Group PT received both taurine and lead acetate; and Group C received distilled water. The pups were weaned at 21 days, but maintained on the same treatments. Pentylene tetrazole seizure thresholds were determined at 42 days. Thresholds in Group P were significantly depressed relative to Group C (56.0 mg/kg v 79.9 mg/kg). Taurine supplementation had no effect on threshold (T = 72.7 mg/kg). However, thresholds in Group PT were significantly higher than those of Group P (PT = 85.2 mg/kg). These data show that whereas taurine was without effect on the threshold of animals not stressed by exposure to lead, it had a protective effect on exposed animals. As human neonates are unable to synthesize taurine, the findings reinforce the concept of taurine being a conditionally essential nutrient in developing humans.

  4. Overexpression of ATP Sulfurylase in Indian Mustard Leads to Increased Selenate Uptake, Reduction, and Tolerance1

    E-Print Network [OSTI]

    Overexpression of ATP Sulfurylase in Indian Mustard Leads to Increased Selenate Uptake, Reduction by plants appeared to be limited by its reduction, a step that is thought to be mediated by ATP sulfurylase. Here, the Arabidopsis APS1 gene, encoding a plastidic ATP sulfurylase, was constitutively overexpressed

  5. Leading Edge 204 Cell 141, April 16, 2010 2010 Elsevier Inc.

    E-Print Network [OSTI]

    Zewail, Ahmed

    Leading Edge Commentary 204 Cell 141, April 16, 2010 ©2010 Elsevier Inc. The world goes through with the first Nobel Prizes in 1901. Science and technology played a pivotal role in this progress. In the 1990s with the creation of the European Union (EU), and China, Japan, and other so-called Asian Tigers assumed a major

  6. As a leading research university with a distinctive commitment to undergraduate education, Rice

    E-Print Network [OSTI]

    Richards-Kortum, Rebecca

    1 #12;2 Mission As a leading research university with a distinctive commitment to undergraduate in fall 2004 #12;4 Expanding academic endeavor 2006: NanoJapan (U.S.-Japan cooperative research Infodynamics with Nanyang Technological University, Singapore 2010: Institute for Urban Research 2010

  7. BNY Mellon -Leading the way across the globe Manchester Metropolitan University

    E-Print Network [OSTI]

    BNY Mellon - Leading the way across the globe Manchester Metropolitan University 2012 #12;Page 2 business Established The Bank of New York Securities Co. Japan, Ltd. Established BNY Luxembourg Acquired) Luxembourg A radical increase in product breadth and global reach Early adopters of mainframe technology 1900

  8. Effects of Eutrophication on Concentrations and Speciation of Copper, Zinc, and Lead in West Falmouth Harbor

    E-Print Network [OSTI]

    Vallino, Joseph J.

    Effects of Eutrophication on Concentrations and Speciation of Copper, Zinc, and Lead in West anoxic conditions and high carbon content favor relatively stable forms of heavy metals, eutrophication suggest that conditions associated with eutrophication do increase heavy metal retention in West Falmouth

  9. System for agitating the acid in a lead-acid battery

    DOE Patents [OSTI]

    Weintraub, Alvin (Schenectady, NY); MacCormack, Robert S. (Glenville, NY)

    1987-01-01T23:59:59.000Z

    A system and method for agitating the acid in a large lead-sulfuric acid storage battery of the calcium type. An air-lift is utilized to provide the agitation. The air fed to the air-lift is humidified prior to being delivered to the air-lift.

  10. Observation of Z production in proton-lead collisions at LHCb

    E-Print Network [OSTI]

    Counts, Ian Thomas Hunt

    The first observation of Z boson production in proton-lead collisions at a centre-of-mass energy per proton-nucleon pair of ?sNN = 5 TeV is presented. The data sample corresponds to an integrated luminosity of 1.6 ...

  11. Recycle Batteries CSM recycles a variety of battery types including automotive, sealed lead acid, nickel

    E-Print Network [OSTI]

    metal hydride and lithium ion batteries. The use of these batteries is increasing as a green, nickel metal hydride and lithium ion batteries. Please contact EHS if you need an accumulation containerRecycle Batteries CSM recycles a variety of battery types including automotive, sealed lead acid

  12. Mesenchymal progenitor self-renewal deficiency leads to age-dependent osteoporosis in

    E-Print Network [OSTI]

    Waldman, Stephen D.

    Mesenchymal progenitor self-renewal deficiency leads to age-dependent osteoporosis in Sca-1 Ly-6A) The cellular and molecular mechanisms that underlie age-dependent osteoporosis, the most common disease uncharacterized mechanism of age-dependent osteoporosis in humans. Osteoporosis is a multifactorial, age

  13. Training Environmental Public Health Leaders From childhood lead poisoning in Philadelphia to tank barge

    E-Print Network [OSTI]

    Training Environmental Public Health Leaders 6/8/2010 From childhood lead poisoning in Philadelphia to tank barge emissions in Memphis, from food safety in Portland, Maine, to air quality in the San Joaquin in everyday life--in homes, in schools, in water supplies, at food markets, and in restaurants. Local EH

  14. A Positive-Weight Next-to-Leading-Order Monte Carlo for Heavy Flavour Hadroproduction

    E-Print Network [OSTI]

    Stefano Frixione; Paolo Nason; Giovanni Ridolfi

    2007-09-22T23:59:59.000Z

    We present a next-to-leading order calculation of heavy flavour production in hadronic collisions that can be interfaced to shower Monte Carlo programs. The calculation is performed in the context of the POWHEG method. It is suitable for the computation of charm, bottom and top hadroproduction. In the case of top production, spin correlations in the decay products are taken into account.

  15. Recommendations for Preventing Lead Poisoning among the Internally Displaced Roma Population in Kosovo

    E-Print Network [OSTI]

    in Europe. The Trepca smelter in Mitrovica extracted metals including zinc, arsenic, lead, and cadmium from in the past, providing employment in both the smelter and the mines to people in the region, but the UN halted (BLLs). Work is underway to reopen the Trepca smelter and mining compound in North Mitrovica. Currently

  16. Transport of lead and diesel fuel through a peat soil near Juneau, AK: a pilot study

    E-Print Network [OSTI]

    Walter, M.Todd

    Transport of lead and diesel fuel through a peat soil near Juneau, AK: a pilot study Julian Deissa; accepted 6 February 2004 Abstract A set of peat column experiments was used to determine the transport-bearing stream 250 m from the site. Three pairs of peat columns were extracted from the rifle range for analysis

  17. NONAXISYMMETRIC ENDWALL CONTOURING AND LEADING EDGE MODIFICATIONS ON TURBINE NOZZLE GUIDE VANES

    E-Print Network [OSTI]

    Guiltinan, Mark

    PENNSTATE _ NONAXISYMMETRIC ENDWALL CONTOURING AND LEADING EDGE MODIFICATIONS ON TURBINE NOZZLE:00 am 228 Hammond Building "The three main sources of the total pressure deficit in a turbine stage to endwall boundary layer in a turbine passage may represent about one third of the total loss measured

  18. Leading a Horse to Water: Using Automated Reminders to Increase Use of Online Decision Support

    E-Print Network [OSTI]

    Cimino, James J.

    Leading a Horse to Water: Using Automated Reminders to Increase Use of Online Decision Support during the course of clinical care. For example, Ely and colleagues found that physicians in clinical appropriate information resources in the course of patient care. Indeed, this is the method primarily used

  19. Leading-order hadronic contributions to the electron and tau anomalous magnetic moments

    E-Print Network [OSTI]

    Burger, Florian; Jansen, Karl; Petschlies, Marcus

    2015-01-01T23:59:59.000Z

    The leading hadronic contributions to the anomalous magnetic moments of the electron and the $\\tau$-lepton are determined by a four-flavour lattice QCD computation with twisted mass fermions. The continuum limit is taken and systematic uncertainties are quantified. Full agreement with results obtained by phenomenological analyses is found.

  20. Resveratrol Improves Survival, Hemodynamics and Energetics in a Rat Model of Hypertension Leading to

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Resveratrol Improves Survival, Hemodynamics and Energetics in a Rat Model of Hypertension Leading and vascular function as well as cardiac and skeletal muscle energy metabolism were assessed in a hypertensive/kg/day; HS-RSV) was given for 8 weeks after hypertension and cardiac hypertrophy were established (which

  1. TOWARDS BENCHMARK MEASUREMENTS FOR USED NUCLEAR FUEL ASSAY USING A LEAD SLOWING-DOWN SPECTROMETER

    E-Print Network [OSTI]

    Danon, Yaron

    for spent fuel testing. The characterization of spent fuel is particularly important for nuclear safeguardsTOWARDS BENCHMARK MEASUREMENTS FOR USED NUCLEAR FUEL ASSAY USING A LEAD SLOWING-DOWN SPECTROMETER B) is considered as a possible option for non- destructive assay of fissile material in used nuclear fuel

  2. Company Profile Mobileye is the leading provider of automated driver assistance technologies to the automotive industry.

    E-Print Network [OSTI]

    Adler, Joan

    leading European car manufacturers. Additional OEMs and Tier 1 suppliers have Mobileye evaluation systems computers and at a fraction of the cost. EyeQ meets automotive cabin grade qualification requirements. Agreements have already been signed with several automotive manufacturers and Tier-1 suppliers

  3. Nov. 28, 2011 Leading Australian climate change communicator to hold BC lecture

    E-Print Network [OSTI]

    Pedersen, Tom

    Knowledge. This year has also seen the book release of Climate Change Denial: Heads in the Sand, coMEDIA TIP Nov. 28, 2011 Leading Australian climate change communicator to hold BC lecture analyses climate change skeptics' arguments against actual peer-reviewed scientific findings -- has

  4. Current Lead Design for the Accelerator Project for Upgrade of LHC

    SciTech Connect (OSTI)

    Brandt, Jeffrey S.; Cheban, Sergey; Feher, Sandor; Kaducak, Marc; Nobrega, Fred; Peterson, Tom

    2010-01-01T23:59:59.000Z

    The Accelerator Project for Upgrade of LHC (APUL) is a U.S. project participating in and contributing to CERN's Large Hadron Collider (LHC) upgrade program. In collaboration with Brookhaven National Laboratory, Fermilab is developing sub-systems for an upgrade of the LHC final focus magnet systems. A concept of main and auxiliary helium flow was developed that allows the superconductor to remain cold while the lead body warms up to prevent upper section frosting. The auxiliary flow will subsequently cool the thermal shields of the feed box and the transmission line cryostats. A thermal analysis of the current lead central heat exchange section was performed using analytic and FEA techniques. A method of remote soldering was developed that allows the current leads to be field replaceable. The remote solder joint was designed to be made without flux or additional solder, and able to be remade up to ten full cycles. A method of upper section attachment was developed that allows high pressure sealing of the helium volume. Test fixtures for both remote soldering and upper section attachment for the 13 kA lead were produced. The cooling concept, thermal analyses, and test results from both remote soldering and upper section attachment fixtures are presented.

  5. Aurora Progress Report The UK is taking a leading role in developing the European

    E-Print Network [OSTI]

    Aurora Progress Report #12;The UK is taking a leading role in developing the European Mars Working Group. Aurora is a European Space Agency (ESA) programme for long-term European involvement and institutions that are part of the UK Aurora programme and helps deliver a number of important benefits. 2

  6. Evaluation of a sodium/Hastelloy-X heat pipe for wing leading edge cooling

    SciTech Connect (OSTI)

    Merrigan, M.A.; Sena, J.T. [Los Alamos National Lab., NM (United States); Glass, D.E. [Analytical Services and Materials, Hampton, VA (United States)

    1996-12-31T23:59:59.000Z

    This report covers assembly of a sodium heat pipe, testing to verify performance during start-up and under steady-state conditions with stagnation point heat loads to about 80 W/cm{sup 2}, performance analysis and evaluation. Evaluation of this leading edge cooling concept is offered and recommendations for further research discussed.

  7. Charge-Separation in Uranium Diazomethane Complexes Leading to C-H Activation and Chemical Transformation

    E-Print Network [OSTI]

    Meyer, Karsten

    coordination and organometallic chemistry.1-3 The covalency in uranium ligand bonds is weaker thanCharge-Separation in Uranium Diazomethane Complexes Leading to C-H Activation and ChemicalVersity of California, San Diego, Department of Chemistry, 9500 Gilman DriVe, La Jolla, California 92093, and Uni

  8. ISO 191** Standards for NASA SiriJodha Singh Khalsa, Lead

    E-Print Network [OSTI]

    Christian, Eric

    ISO 191** Standards for NASA SiriJodha Singh Khalsa, Lead MENDS Tiger Team to support ISO metadata ­ GCMD and ECHO both acGvely working on ISO ­ Missions and data centers looking at ISO · FGDC has endorsed ISO 19115 ­ OMB mandated all

  9. Energizing the Next Generation with Photovoltaics Following the lead of Russian colleagues, photovoltaic (PV)

    E-Print Network [OSTI]

    Oregon, University of

    Energizing the Next Generation with Photovoltaics ABSTRACT Following the lead of Russian colleagues, photovoltaic (PV) lab kits are being built and experiments and curricula are being developed for use of these kits. This Photovoltaic Sci- ence Experiments and Curriculum (PSEC) is being tested in local high

  10. Leading innovation in food, natural resources and energy Michigan State University

    E-Print Network [OSTI]

    Liu, Taosheng

    City Research Center includes 810 acres of managed land and 180 beef cows in a geographic area suitableLeading innovation in food, natural resources and energy Michigan State University Research Centers.agbioresearch.msu.edu 2 3 PHOTO:GWENSKINNER PHOTO:RAYMILLER PHOTO:GREGKOWALEWSKI #12;LAKE CITY RESEARCH CENTER The Lake

  11. www.energy.psu.edu The EMS Energy Institute at Penn State is a leading research

    E-Print Network [OSTI]

    Lee, Dongwon

    www.energy.psu.edu The EMS Energy Institute at Penn State is a leading research and development organization focused on energy science and engineering. We are committed to: -- Providing academic and technical leadership in the development and assessment of energy technologies, -- Providing Penn State

  12. Study of the self-organization processes in lead sulfide quantum dots

    SciTech Connect (OSTI)

    Tarasov, S. A., E-mail: SATarasov@mail.ru; Aleksandrova, O. A.; Maksimov, A. I.; Maraeva, E. V.; Matyushkin, L. B.; Men’kovich, E. A.; Moshnikov, V. A. [St. Petersburg Electrotechnical University LETI (Russian Federation); Musikhin, S. F. [St. Petersburg State Polytechnic University (Russian Federation)

    2014-12-15T23:59:59.000Z

    A procedure is described for the synthesis of nanoparticles based on lead chalcogenides. The procedure combines the synthesis of colloidal quantum dots (QDs) in aqueous solutions with simultaneous organization of the QDs into ordered arrays. The processes of the self-organization of QDs are analyzed at the nano- and microscopic levels by the photoluminescence method, atomic-force microscopy, and optical microscopy.

  13. APRIL 1998 THE LEADING EDGE 461 ncreases in computing power and advances in mathe-

    E-Print Network [OSTI]

    Oldenburg, Douglas W.

    optimization theory have combined to produce a new generation of algorithms that can invert geophysical dataAPRIL 1998 THE LEADING EDGE 461 ncreases in computing power and advances in mathe- matical. In this short article, we illustrate both the practicability of inverting geophysical data and the impor- tant

  14. Effects of Dietary Lead and Cholesterol Supplementation on Hemolysis in the Sprague-Dawley Rat1

    E-Print Network [OSTI]

    Moore, Paul A.

    INTRODUCTION Lead is one of the most toxic heavy metals found in the environment (Needleman and others 1990) and has become the most widely distributed toxic heavy metal in the urban environment as a result of its that heavy metals inhibit cholesterol synthesis, which leaves insufficient cholesterol for the maintenance

  15. Comment/Rebuttal Comments on "Electrorheology Leads to Efficient Combustion" by

    E-Print Network [OSTI]

    GĂĽlder, Ă?mer L.

    Comment/Rebuttal Comments on "Electrorheology Leads to Efficient Combustion" by Tao et al. O¨ mer L of combustion in general and internal combustion (IC) engine combustion technology in particular. Given posit that "because combustion starts at the interface between fuel and air and most harmful emissions

  16. 1092 The Leading Edge September 2008 The SEG Foundation's Summer Field Camp grant

    E-Print Network [OSTI]

    seismic sur- veys and geoscientific data services to the oil and gas indus- try worldwide Gary Servos, Chairman of the SEG Foundation Board of Directors. "This lead- ership investment by TGS Hank Hamilton (left) and COO Robert Hobbs (center) on their leadership investment in Advancing

  17. A Dynamic Inventory Control Policy Under Demand, Yield and Lead Time Uncertainties

    E-Print Network [OSTI]

    Boyer, Edmond

    A Dynamic Inventory Control Policy Under Demand, Yield and Lead Time Uncertainties Mohamed Zied@lgi.ecp.fr, dallery@lgi.ecp.fr) ABSTRACT In this paper, we analyze a single-stage and single-item inventory control it. Keywords: inventory control, forecasts, cycle service level, fill rate, safety stock, policy

  18. The Colorado State Forest Service is the lead state agency for forestry and wildfire expertise.

    E-Print Network [OSTI]

    The Colorado State Forest Service is the lead state agency for forestry and wildfire expertise. Colorado State Forest Service http://csfs.colostate.edu/ CSFS is proud to be a part of the Warner College of Natural Resources at Colorado State University, headquartered in Fort Collins. We have approximately 130

  19. INEOS Scholarship Opportunity 2013 INEOS is a young and vibrant leading petrochemical company which has grown

    E-Print Network [OSTI]

    Painter, Kevin

    and the petrochemical plants. Located 20 miles west of Edinburgh on a 1700-acre site, the petrochemicals facilityINEOS Scholarship Opportunity 2013 INEOS is a young and vibrant leading petrochemical company which employees in the company success. The Grangemouth refinery and petrochemicals facility is the largest INEOS

  20. Access of Cellulase to Cellulose and Lignin for Poplar Solids Produced by Leading Pretreatment Technologies

    E-Print Network [OSTI]

    California at Riverside, University of

    Access of Cellulase to Cellulose and Lignin for Poplar Solids Produced by Leading Pretreatment and adsorption of b-glucosidase for lignin left after enzymatic digestion of the solids from these pretreatments effectiveness was determined. Furthermore, Avicel hydrolysis inhibition by enzymatic and acid lignin of poplar

  1. Identification of lead chemical form in mine waste materials by X-ray absorption spectroscopy

    SciTech Connect (OSTI)

    Taga, Raijeli L.; Ng, Jack [University of Queensland, National Research Centre for Environmental Toxicology (EnTox), Brisbane, 4108 (Australia); Zheng Jiajia; Huynh, Trang; Noller, Barry [University of Queensland, Centre for Mined Land Rehabilitation, Brisbane, 4072 (Australia); Harris, Hugh H. [School of Chemistry and Physics, University of Adelaide, Adelaide, 5005 (Australia)

    2010-06-23T23:59:59.000Z

    X-ray absorption spectroscopy (XAS) provides a direct means for measuring lead chemical forms in complex samples. In this study, XAS was used to identify the presence of plumbojarosite (PbFe{sub 6}(SO{sub 4}){sub 4}(OH){sub 12}) by lead L{sub 3}-edge XANES spectra in mine waste from a small gold mining operation in Fiji. The presence of plumbojarosite in tailings was confirmed by XRD but XANES gave better resolution. The potential for human uptake of Pb from tailings was measured using a physiologically based extract test (PBET), an in-vitro bioaccessibility (BAc) method. The BAc of Pb was 55%. Particle size distribution of tailings indicated that 40% of PM{sub 10} particulates exist which could be a potential risk for respiratory effects via the inhalation route. Food items collected in the proximity of the mine site had lead concentrations which exceed food standard guidelines. Lead within the mining lease exceeded sediment guidelines. The results from this study are used to investigate exposure pathways via ingestion and inhalation for potential risk exposure pathways of Pb in that locality. The highest Pb concentration in soil and tailings was 25,839 mg/kg, exceeding the Australian National Environment Protection Measure (NEPM) soil health investigation levels.

  2. energy: Supply, Demand, and impacts CooRDinATinG LeAD AUThoR

    E-Print Network [OSTI]

    Kammen, Daniel M.

    240 chapter 12 energy: Supply, Demand, and impacts CooRDinATinG LeAD AUThoR Vincent C. Tidwell the potential to impact the production, demand, and delivery of energy in a number of ways. Chapter citation;energy: supply, demand, and impacts 241 · Delivery of electricity may become more vulnerable

  3. CBER-DETR Nevada Coincident and Leading Employment Storm Clouds Darkening Again on the Nevada Economy

    E-Print Network [OSTI]

    Ahmad, Sajjad

    Statistics. The Nevada Coincident Employment Index includes four employment measures ­ household employmentCBER-DETR Nevada Coincident and Leading Employment Indexes1 Storm Clouds Darkening Again on the Nevada Economy The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy

  4. CBER-DETR Nevada Coincident and Leading Employment Slow Recovery in Nevada's Economy Continues

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Slow Recovery in Nevada's Economy Continues The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using

  5. CBER-DETR Nevada Coincident and Leading Employment Sailing in the Doldrums

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Sailing in the Doldrums The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index of employment

  6. CBER-DETR Nevada Coincident and Leading Employment Did the Nevada Employment Recession End?

    E-Print Network [OSTI]

    Ahmad, Sajjad

    Statistics. The Nevada Coincident Employment Index includes four employment measures ­ household employmentCBER-DETR Nevada Coincident and Leading Employment Indexes1 Did the Nevada Employment Recession End? Coincident Index Moves Higher from October 2009 The Nevada Coincident Employment Index measures the ups

  7. CBER-DETR Nevada Coincident and Leading Employment The Nevada Recovery: Progress Continues

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 The Nevada Recovery: Progress Continues The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index

  8. CBER-DETR Nevada Coincident and Leading Employment Both Indexes Up in September 2012

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Both Indexes Up in September 2012 The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index

  9. CBER-DETR Nevada Coincident and Leading Employment Mixed Signals Still Persist

    E-Print Network [OSTI]

    Ahmad, Sajjad

    Statistics. The Nevada Coincident Employment Index includes four employment measures ­ household employmentCBER-DETR Nevada Coincident and Leading Employment Indexes1 Mixed Signals Still Persist The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index of employment

  10. CBER-DETR Nevada Coincident and Leading Employment Another Good Month for the Indexes

    E-Print Network [OSTI]

    Ahmad, Sajjad

    Statistics. The Nevada Coincident Employment Index includes four employment measures ­ household employmentCBER-DETR Nevada Coincident and Leading Employment Indexes1 Another Good Month for the Indexes The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index

  11. CBER-DETR Nevada Coincident and Leading Employment Indexes Show a Pause in the Recovery

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the Current Employment Statistics (Establishment Survey) back to January 2011. Figure 1 encompasses fourCBER-DETR Nevada Coincident and Leading Employment Indexes1 Indexes Show a Pause in the Recovery The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index

  12. CBER-DETR Nevada Coincident and Leading Employment No Clear Signal

    E-Print Network [OSTI]

    Ahmad, Sajjad

    by the Bureau of Labor Statistics. The Nevada Coincident Employment Index includes four employment measuresCBER-DETR Nevada Coincident and Leading Employment Indexes1 No Clear Signal by Bob Potts Center for Business and Economic Research University of Nevada, Las Vegas The Nevada Coincident Employment Index

  13. CBER-DETR Nevada Coincident and Leading Employment Both Indexes Drop in July

    E-Print Network [OSTI]

    Ahmad, Sajjad

    Statistics. The Nevada Coincident Employment Index includes four employment measures ­ household employmentCBER-DETR Nevada Coincident and Leading Employment Indexes1 Both Indexes Drop in July The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index of employment

  14. CBER-DETR Nevada Coincident and Leading Employment Both Indexes Drop for Second Month

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Both Indexes Drop for Second Month The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index

  15. CBER-DETR Nevada Coincident and Leading Employment Weak National Recovery Lengthens Nevada's Employment Recession

    E-Print Network [OSTI]

    Ahmad, Sajjad

    Statistics. The Nevada Coincident Employment Index includes four employment measures ­ household employmentCBER-DETR Nevada Coincident and Leading Employment Indexes1 Weak National Recovery Lengthens Nevada's Employment Recession The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy

  16. CBER-DETR Nevada Coincident and Leading Employment Bumps in the Road of Recovery

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Bumps in the Road of Recovery The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index

  17. CBER-DETR Nevada Coincident and Leading Employment Did the Nevada Employment Recession End?

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Did the Nevada Employment Recession End? Jury Still Out! The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy

  18. CBER-DETR Nevada Coincident and Leading Employment Anyone for a Double Dip?

    E-Print Network [OSTI]

    Ahmad, Sajjad

    Statistics. The Nevada Coincident Employment Index includes four employment measures ­ household employmentCBER-DETR Nevada Coincident and Leading Employment Indexes1 Anyone for a Double Dip? The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index of employment

  19. CBER-DETR Nevada Coincident and Leading Employment Will 2011 Usher in a Recovery in Nevada?

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Will 2011 Usher in a Recovery in Nevada? The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using an index

  20. CBER-DETR Nevada Coincident and Leading Employment Benchmark Revisions Add Employment to Nevada

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Benchmark Revisions Add Employment to Nevada The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using

  1. CBER-DETR Nevada Coincident and Leading Employment Recovery Continues Down the Long Road Back

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Recovery Continues Down the Long Road Back The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using

  2. CBER-DETR Nevada Coincident and Leading Employment Employment Recovery in Nevada Continues Its Slow Pace

    E-Print Network [OSTI]

    Ahmad, Sajjad

    by the Bureau of Labor Statistics. The Nevada Coincident Employment Index includes four employment measuresCBER-DETR Nevada Coincident and Leading Employment Indexes1 Employment Recovery in Nevada Continues Its Slow Pace The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy

  3. CBER-DETR Nevada Coincident and Leading Employment Will Nevada Experience a Double Dip Recession?

    E-Print Network [OSTI]

    Ahmad, Sajjad

    the seasonally adjusted data reported by the Bureau of Labor Statistics. The Nevada Coincident Employment IndexCBER-DETR Nevada Coincident and Leading Employment Indexes1 Will Nevada Experience a Double Dip Recession? The Nevada Coincident Employment Index measures the ups and downs of the Nevada economy using

  4. Compatibility of SiC and SiC Composites with Molten Lead

    SciTech Connect (OSTI)

    H Tunison

    2006-03-07T23:59:59.000Z

    The choice of structural material candidates to contain Lead at 1000 C are limited in number. Silicon carbide composites comprise one choice of possible containment materials. Short term screening studies (120 hours) were undertaken to study the behavior of Silicon Carbide, Silicon Nitride, elemental Silicon and various Silicon Carbide fiber composites focusing mainly on melt infiltrated composites. Isothermal experiments at 1000 C utilized graphite fixtures to contain the Lead and material specimens under a low oxygen partial pressure environment. The corrosion weight loss values (grams/cm{sup 2} Hr) obtained for each of the pure materials showed SiC (monolithic CVD or Hexoloy) to have the best materials compatibility with Lead at this temperature. Increased weight loss values were observed for pure Silicon Nitride and elemental Silicon. For the SiC fiber composite samples those prepared using a SiC matrix material performed better than Si{sub 3}N{sub 4} as a matrix material. Composites prepared using a silicon melt infiltration process showed larger corrosion weight loss values due to the solubility of silicon in lead at these temperatures. When excess silicon was removed from these composite samples the corrosion performance for these material improved. These screening studies were used to guide future long term exposure (both isothermal and non-isothermal) experiments and Silicon Carbide composite fabrication work.

  5. Economic Evaluation of Leading Technology Options for Sequestration of Carbon Dioxide

    E-Print Network [OSTI]

    1 Economic Evaluation of Leading Technology Options for Sequestration of Carbon Dioxide by Jérémy, which releases nearly six billion tons of carbon per year into the atmosphere. These fuels will continue development. Since power plants are the largest point sources of CO2 emissions, capturing the carbon dioxide

  6. Next-to-Leading Order Predictions for W + 3-Jet Distributions at Hadron Colliders

    SciTech Connect (OSTI)

    Berger, C.F.; /MIT, LNS; Bern, Z.; /UCLA; Dixon, L.J.; /SLAC; Febres Cordero, F.; /UCLA; Forde, D.; Gleisberg, T.; /SLAC; Ita, H.; /UCLA; Kosower, D.A.; /Saclay, SPhT; Maitre, D.; /Durham U.

    2009-12-09T23:59:59.000Z

    We present next-to-leading order QCD predictions for a variety of distributions in W + 3-jet production at both the Tevatron and the Large Hadron Collider. We include all subprocesses and incorporate the decay of the W boson into leptons. Our results are in excellent agreement with existing Tevatron data and provide the first quantitatively precise next-to-leading order predictions for the LHC. We include all terms in an expansion in the number of colors, confirming that the specific leading-color approximation used in our previous study is accurate to within three percent. The dependence of the cross section on renormalization and factorization scales is reduced significantly with respect to a leading-order calculation. We study different dynamical scale choices, and find that the total transverse energy is significantly better than choices used in previous phenomenological studies. We compute the one-loop matrix elements using on-shell methods, as numerically implemented in the BlackHat code. The remaining parts of the calculation, including generation of the real-emission contributions and integration over phase space, are handled by the SHERPA package.

  7. Williams Companies Distinguished Chair in Energy Technology Raj Singh will lead

    E-Print Network [OSTI]

    Piao, Daqing

    Williams Companies Distinguished Chair in Energy Technology Raj Singh will lead the new school Williams Companies Distinguished Chair in Energy Technology. "I'm quite excited by what we are doing at OSU Companies Distinguished Chair in Energy Technology. As the chair, Singh will research advanced materials

  8. Application of Kernel Principal Component Analysis for Single Lead ECG-Derived Respiration

    E-Print Network [OSTI]

    1 Application of Kernel Principal Component Analysis for Single Lead ECG-Derived Respiration Devy signal from ECGs. In this study, an improved ECG-derived respiration (EDR) algorithm based on kernel PCA ECGs. Index Terms--ECG-derived respiration (EDR), kernel princi- pal component analysis (kPCA). I

  9. Measurement of Leading Neutron Production in Deep-Inelastic Scattering at HERA

    E-Print Network [OSTI]

    Aaron, F D; Alimujiang, K; Andreev, V; Antunovic, B; Backovic, S; Baghdasaryan, A; Barrelet, E; Bartel, W; Begzsuren, K; Belousov, A; Bizot, J C; Boudry, V; Bozovic-Jelisavcic, I; Bracinik, J; Brandt, G; Brinkmann, M; Brisson, V; Bruncko, D; Bunyatyan, A; Buschhorn, G; Bystritskaya, L; Campbell, A J; Cantun Avila, K B; Cerny, K; Cerny, V; Chekelian, V; Cholewa, A; Contreras, J G; Coughlan, J A; Cozzika, G; Cvach, J; Dainton, J B; Daum, K; Deak, M; Delcourt, B; Delvax, J; De Wolf, E A; Diaconu, C; Dodonov, V; Dossanov, A; Dubak, A; Eckerlin, G; Efremenko, V; Egli, S; Eliseev, A; Elsen, E; Falkiewicz, A; Favart, L; Fedotov, A; Felst, R; Feltesse, J; Ferencei, J; Fischer, D.-J; Fleischer, M; Fomenko, A; Gabathuler, E; Gayler, J; Ghazaryan, Samvel; Glazov, A; Glushkov, I; Goerlich, L; Gogitidze, N; Gouzevitch, M; Grab, C; Greenshaw, T; Grell, B R; Grindhammer, G.; Habib, S; Haidt, D; Helebrant, C; Henderson, R C W; Hennekemper, E; Henschel, H; Herbst, M; Herrera, G; Hildebrandt, M; Hiller, K H; Hoffmann, D; Horisberger, R; Hreus, T; Jacquet, M; Janssen, X; Jonsson, L; Jung, Andreas Werner; INSPIRE-00183962; Jung, H; Kapichine, M; Katzy, J; Kenyon, I R; Kiesling, C; Klein, M; Kleinwort, C; Kluge, T; Knutsson, A; Kogler, R; Kostka, P; Kraemer, M; Krastev, K; Kretzschmar, J; Kropivnitskaya, A; Kruger, K; Kutak, K; Landon, M P J; Lange, W; Lastovicka-Medin, G; Laycock, P; Lebedev, A; Lendermann, V; Levonian, S; Li, G; Lipka, K; Liptaj, A; List, B; List, J; Loktionova, N; Lopez-Fernandez, R; Lubimov, V; Lytkin, L; Makankine, A; Malinovski, E; Marage, P; Marti, Ll; Martyn, H.-U.; Maxfield, S J; Mehta, A; Meyer, A B; Meyer, H; Meyer, H; Meyer, J; Mikocki, S; Milcewicz-Mika, I; Moreau, F; Morozov, A; Morris, J V; Mozer, Matthias Ulrich; Mudrinic, M; Muller, K; Murin, P; Naumann, Th; Newman, P R; Niebuhr, C; Nikiforov, A; Nikitin, D; Nowak, G; Nowak, K; Olsson, J E; Osman, S; Ozerov, D; Pahl, P; Palichik, V; Panagoulias, I; Pandurovic, M; Papadopoulou, Th; Pascaud, C; Patel, G D; Pejchal, O; Perez, E; Petrukhin, A; Picuric, I; Piec, S; Pitzl, D; Placakyte, R; Pokorny, B; Polifka, R; Povh, B; Radescu, V; Rahmat, A J; Raicevic, N; Raspiareza, A; Ravdandorj, T; Reimer, P; Rizvi, E; Robmann, P; Roland, B; Roosen, R; Rostovtsev, A; Rotaru, M; Ruiz Tabasco, J E; Rusakov, S; Salek, D; Sankey, D P C; Sauter, M; Sauvan, E; Schmitt, S; Schoeffel, L; Schoning, A; Schultz-Coulon, H.-C; Sefkow, F; Shaw-West, R N; Shtarkov, L N; Shushkevich, S; Sloan, T; Smiljanic, Ivan; Soloviev, Y; Sopicki, P; South, D; Spaskov, V; Specka, Arnd E; Staykova, Z; Steder, M; Stella, B; Stoicea, G; Straumann, U.; Sunar, D; Sykora, T; Tchoulakov, V; Thompson, G; Thompson, P D; Toll, T; Tomasz, F; Tran, T H; Traynor, D; Trinh, T N; Truol, P; Tsakov, I; Tseepeldorj, B; Turnau, J; Urban, K; Valkarova, A; Vallee, C; Van Mechelen, P; Vargas Trevino, A; Vazdik, Y; Vinokurova, S; Volchinski, V; von den Driesch, M; Wegener, D; Wissing, Ch; Wunsch, E; Zacek, J; Zalesak, J; Zhang, Z; Zhokin, A; Zimmermann, T; Zohrabyan, H; Zomer, F

    2010-01-01T23:59:59.000Z

    The production of leading neutrons, where the neutron carries a large fraction x_L of the incoming proton's longitudinal momentum, is studied in deep-inelastic positron-proton scattering at HERA. The data were taken with the H1 detector in the years 2006 and 2007 and correspond to an integrated luminosity of 122 pb^{-1}. The semi-inclusive cross section is measured in the phase space defined by the photon virtuality 6 < Q^2 < 100 GeV^2, Bjorken scaling variable 1.5x10^{-4} < x < 3x10^{-2}, longitudinal momentum fraction 0.32 < x_L < 0.95 and neutron transverse momentum p_T < 0.2 GeV. The leading neutron structure function, F_2^{LN(3)}(Q^2,x,x_L), and the fraction of deep-inelastic scattering events containing a leading neutron are studied as a function of Q^2, x and x_L. Assuming that the pion exchange mechanism dominates leading neutron production, the data provide constraints on the shape of the pion structure function.

  10. Residues of lead, cadmium, and arsenic in livers of Mexican free-tailed bats

    SciTech Connect (OSTI)

    Thies, M.; Gregory, D. (Oklahoma State Univ., Stillwater (United States))

    1994-05-01T23:59:59.000Z

    Since 1936, the size of the summer population of Mexican free-tailed bats, Tadarida brasiliensisat Carlsbad Caverns, New Mexico, declined from an estimated 8.7 million to 700,000 in 1991. This decline has been attributed primarily to human disturbance and the heavy agricultural use of organochlorine pesticides. Members of this species forage extensively over heavily agricultural areas, feeding on insects potentially contaminated with high levels of insecticides and trace metals. However, contamination from elements such as lead, cadmium, and arsenic have not been examined. The accumulation of these elements in wild vertebrates is often a primary reflection of contamination of the food supply. The presence of elemental contaminants in body tissues of bats is poorly documented. The objectives of this study were to examine and compare lead, cadmium, and arsenic contamination in livers of adult T. Brasiliensis from Carlsbad Caverns and Vickery Cave, a maternity colony in northwestern Oklahoma. Lead, cadmium, and arsenic were specifically selected because of their documented toxic and/or reproductive effects and their potential availability to this species. Large quantities of tetraethyl lead have been released into the environment and other lead compounds continue to be released by industrial manufacturing and petroleum refinement processes. Cadmium is used in a number of industrial processes such as metal plating and fabrication of alloys and is released from phosphate fertilizers and combusted coals. Teratogenicity appears to be greater for cadmium than for other elements. Arsenical compounds have been commonly used as herbicides and defoliants. These compounds have been demonstrated to cause abnormal embryonic development, degenerative tissue changes, cancer, chromosomal damage, and death in domestic animals.

  11. Field analysis of arsenic and lead in soils at a former smelter facility

    SciTech Connect (OSTI)

    Wallis, C.M.; Walker, M.T.

    1999-07-01T23:59:59.000Z

    Field X-ray fluorescence (XRF) chemical analyses were performed to efficiently and cost-effectively evaluate arsenic and lead concentrations in soils as part of CERCLA-driven remedial investigations at a former lead smelter. Sample preparation and analysis protocols, including extensive quality control (QC) requirements, were developed for the field XRF method that were accepted by the US Environmental Protection Agency and other regulatory agencies. Over 800 soil samples from approximately 150 borings and test pits were analyzed using the field XRF technique during a three-week period. Measured arsenic and lead concentrations ranged over several orders of magnitude. Costs for using the field XRF technique were about 60 to 70% of the costs for traditional wet chemistry (acid digestion and spectrophotometric analysis) methods, which were also used to analyze selected samples for verification. Split samples analyzed during and immediately after the field investigation showed a good correlation between soil concentrations obtained using field XRF methods and concentrations obtained using laboratory analysis (both XRF and wet chemistry). Correlation coefficients (r{sup 2}) for split samples compared using linear regression ranged from 0.832 to 0.995. Split-sample comparisons were generally better at lower soil concentrations (<10,000 ppm arsenic, <15,000 ppm lead). Duplicate, blank, and control standard results for the field XRF method were within limits typically achieved by laboratory-based systems. Preparation study results suggested that increased levels of soil-sample preparation may not significantly improve data comparability. Overall, results indicated that the field XRF technique is a dependable method for screening-level investigations in which solids are differentiated based on order-of-magnitude differences in arsenic and (or) lead concentrations. The field XRF method allowed rapid turnaround of analytical results while achieving data quality and comparability goals acceptable for a CERCLA remedial investigation.

  12. One-group fission cross sections for plutonium and minor actinides inserted in calculated neutron spectra of fast reactor cooled with lead-208 or lead-bismuth eutectic

    SciTech Connect (OSTI)

    Khorasanov, G. L.; Blokhin, A. I. [State Scientific Center of the Russian Federation, Inst. for Physics and Power Engineering Named after A.I. Leypunsky, Bondarenko Square 1, Obninsk, 249033 (Russian Federation)

    2012-07-01T23:59:59.000Z

    The paper is dedicated to one-group fission cross sections of Pu and MA in LFRs spectra with the aim to increase these values by choosing a coolant which hardens neutron spectra. It is shown that replacement of coolant from Pb-Bi with Pb-208 in the fast reactor RBEC-M, designed in Russia, leads to increasing the core mean neutron energy. As concerns fuel Pu isotopes, their one-group fission cross sections become slightly changed, while more dramatically Am-241 one-group fission cross section is changed. Another situation occurs in the lateral blanket containing small quantities of minor actinides. It is shown that as a result of lateral blanket mean neutron energy hardening the one-group fission cross sections of Np-237, Am-241 and Am-243 increases up to 8-11%. This result allows reducing the time of minor actinides burning in FRs. (authors)

  13. Effects of Microbial and Phosphate Amendments on the Bioavailability of Lead (Pb) in Shooting Range Soil

    SciTech Connect (OSTI)

    Brigmon, Robin; Wilson, Christina; Knox, Anna; Seaman, John; Smith, Garriet

    2005-06-16T23:59:59.000Z

    Heavy metals including lead (Pb) are released continually into the environment as a result of industrial, recreational, and military activities. Lead ranked number two on the CERCLA Priority List of Hazardous Substances and was identified as a major hazardous chemical found on 47% of USEPA's National Priorities List sites (Hettiarachchi and Pierzynski 2004). In-situ remediation of lead (Pb) contaminated soils may be accomplished by changing the soil chemistry and structure with the application of microbial and phosphate amendments. Soil contaminated with lead bullets was collected from the surface of the berm at Savannah River Site (SRS) Small Arms Training Academy (SATA) in Aiken, SC. While uncontaminated soils typically have Pb levels ranging from 2 to 200 mg/kg (Berti et al. 1998), previous analysis show Pb levels of the SATA berm to reach 8,673 mg/kg. Biosurfactants are surface-active compounds naturally produced by soil bacteria that can bind metals. Biosurfactants have a wide variety of chemical structures that reduce interfacial surface tensions (Jennings and Tanner 2000) and have demonstrated efficient metal complexion (Lin 1996). Biosurfactants also have the potential to change the availability of natural organic matter (Strong-Gunderson 1995). Two types of bacteria, Alcaligenes piechaudii and Pseudomonas putida, were employed as amendments based on their ability to produce biosurfactants and survive in metal-contaminated soils. Apatites (calcium phosphate compounds) are important in the formation of Pb phosphates. Pb phosphates form rapidly when phosphate is available and are the most stable environmental form of lead in soil (Ruby et al.1998). Pyromorphites in particular remain insoluble under a wide range of environmental conditions (Zhang et al. 1998). The three apatites evaluated in the current study were North Carolina apatite (NCA), Florida apatite (FA), and biological apatite (BA). BA is ground fish bone that has few impurities such as As, Cr, or U and contains about 27% total phosphate, most of which is available. FA and NCA are two types of rock phosphates that release small amounts of phosphate over time. Total phosphate is around 30% with only 1-2% phosphate available (Knox et al. 2005). In this study, we describe the influence of combining the two microbial and three phosphate amendments on reducing lead bioavailability in shooting range soil.

  14. The production of dense lead-ion beams for the CERN LHC

    E-Print Network [OSTI]

    Bosser, Jacques; Chanel, M; MacCaferri, R; Molinari, G; Maury, S; Möhl, D; Tranquille, G

    2000-01-01T23:59:59.000Z

    To reach the design luminosity for lead-ions in the LHC, the present Low Energy Antiproton Ring (LEAR) has to be converted into a Low Energy Ion Ring (LEIR). Since the present ECR lead-ion source does not provide sufficient intensity, the main goal of LEIR is to act as a low-energy (4.2MeV/u) accumulator where the ion beam is stacked and cooled (with the help of an electron-cooler) to reach the required intensity and emittances. An experimental program has been carried out at LEAR in recent years in order to test the cooling and stacking process with the present electron-cooler. A variety of results have been reported at previous conferences. This paper will focus on the electron cooling aspects resulting from the afore mentioned experiments. Taking into account the experience

  15. Diffractive Dijet Production with a Leading Proton in ep Collisions at HERA

    E-Print Network [OSTI]

    ,

    2015-01-01T23:59:59.000Z

    The cross section of the diffractive process e^+p -> e^+Xp is measured at a centre-of-mass energy of 318 GeV, where the system X contains at least two jets and the leading final state proton p is detected in the H1 Very Forward Proton Spectrometer. The measurement is performed in photoproduction with photon virtualities Q^2 <2 GeV^2 and in deep-inelastic scattering with 4 GeV^2leading order QCD calculations based on diffractive parton distribution functions as extracted from measurements of inclusive cross sections in diffractive deep-inelastic scattering.

  16. Minijet transverse energy production in the next-to-leading order in hadron and nuclear collisions

    E-Print Network [OSTI]

    A. V. Leonidov; D. M. Ostrovsky

    1998-11-23T23:59:59.000Z

    The transverse energy flow generated by minijets in hadron and nuclear collisions into a given rapidity window in the central region is calculated in the next-to-leading (NLO) order in QCD at RHIC and LHC energies. The NLO transverse energy production in pp collisions cross sections are larger than the LO ones by the factors of K_{RHIC} ~ 1.9 and K_{LHC} ~ 2.1 at RHIC and LHC energies correspondingly. These results were then used to calculate transverse energy spectrum in nuclear collisions in a Glauber geometrical model. We show that accounting for NLO corrections in the elementary pp collisions leads to a substantial broadening of the E_{perp} distribution for the nuclear ones, while its form remains practically unchanged.

  17. Metal accumulation in terrestrial pulmonates at a lead/zinc smelter site in Arnoldstein, Austria

    SciTech Connect (OSTI)

    Rabitsch, W.B. [Univ. of Vienna, Vienna (Austria)] [Univ. of Vienna, Vienna (Austria)

    1996-05-01T23:59:59.000Z

    Recently,the suitability of terrestrial gastropods was reviewed as quantitative indicator organisms for environmental metal pollution. The peculiar metal accumulation capabilities in molluscs have been known in detail for decades, but {open_quotes}only few data are available for terrestrial pulmonates{close_quotes}. Furthermore, data are restricted to only a few species, and despite similarities in metabolic pathways, species-specific properties in metal-budget strategies exist. Information concerning the potential range of metal burden in these animals form the field are, therefore, of ecophysical relevance. Snails satisfy a basic demand as quantitative indicators of the bioavailable fraction of terrestrial metal pollution. In this study concentrations of lead, cadmium, copper and zinc were measured in tissues of 4 species of snails collected in the vicinity of a lead/zinc smelter with a long history of pollution. 23 refs., 3 figs., 1 tab.

  18. Studies on the chemical synthesis and characterization of lead oxide nanoparticles with different organic capping agents

    SciTech Connect (OSTI)

    Arulmozhi, K. T., E-mail: arulsheelphy@gmail.com [Physics Wing (DDE), Annamalai University, Tamil Nadu, India - 608 002 (India); Mythili, N. [Department of Physics, Annamalai University, Tamil Nadu, India - 608 002 (India)] [Department of Physics, Annamalai University, Tamil Nadu, India - 608 002 (India)

    2013-12-15T23:59:59.000Z

    Lead oxide (PbO) nanoparticles were chemically synthesized using Lead (II) acetate as precursor. The effects of organic capping agents such as Oleic acid, Ethylene Diamine Tetra Acetic acid (EDTA) and Cetryl Tri Methyl Butoxide (CTAB) on the size and morphology of the nanoparticles were studied. Characterization techniques such as X-ray diffraction (XRD), Fourier Transform-Infrared spectroscopy (FT-IR), Photoluminescence (PL) Field Emission Scanning Electron Microscopy (FE-SEM), Energy Dispersive Spectroscopy (EDS) and Transmission Electron Microscopy (TEM) were used to analyse the prepared nanoparticles for their physical, structural and optical properties. The characterization studies reveal that the synthesized PbO nanoparticles had well defined crystalline structure and sizes in the range of 25 nm to 36 nm for capping agents used and 40 nm for pure PbO nanoparticles.

  19. Heat pipes for wing leading edges of hypersonic vehicles. Final report

    SciTech Connect (OSTI)

    Boman, B.L.; Citrin, K.M.; Garner, E.C.; Stone, J.E.

    1990-01-01T23:59:59.000Z

    Wing leading edge heat pipes were conceptually designed for three types of vehicle: an entry research vehicle, aero-space plane, and advanced shuttle. A full scale, internally instrumented sodium/Hastelloy X heat pipe was successfully designed and fabricated for the advanced shuttle application. The 69.4 inch long heat pipe reduces peak leading edge temperatures from 3500 F to 1800 F. It is internally instrumented with thermocouples and pressure transducers to measure sodium vapor qualities. Large thermal gradients and consequently large thermal stresses, which have the potential of limiting heat pipe life, were predicted to occur during startup. A test stand and test plan were developed for subsequent testing of this heat pipe. Heat pipe manufacturing technology was advanced during this program, including the development of an innovative technique for wick installation.

  20. Identification and Elimination of Mechanisms Leading to UV Damage of DKDP

    SciTech Connect (OSTI)

    Burnham, A; Runkel, M; Chase, L; Demos, S; Staggs, M; Siekhaus, W

    2001-03-06T23:59:59.000Z

    This LDRD project addressed both bulk and surface damage induced by UV-laser exposure. The primary objectives were (1) to complete our understanding of the factors leading to bulk damage, including growth conditions and orientational direction, and (2) to identify mechanisms of surface damage initiation and growth leading to mitigation methods. Due to the more advanced state of knowledge in bulk damage, a greater portion of that work was completed during the one-year term of this project. Three papers were presented at the 32nd Boulder Damage Symposium on Laser-Induced Damage in Optical Materials, and the three resulting manuscripts submitted to the Proceeding are attached: An important result from this work is that it established a dependence of obscuration from bulk damage on fluence and pulse length, which is shown.