Powered by Deep Web Technologies
Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Single-state electronic ballast with dimming feature and unity power factor  

SciTech Connect

Analysis, design, and practical consideration of a single-stage electronic ballast with dimming feature and unity power factor are presented in this paper. The proposed single-stage ballast is the combination of a boost converter and a half-bridge series-resonant parallel-loaded inverter. The boost semistage working in the discontinuous conduction mode functions as a power factor corrector and the inverter semistage operated above resonance are employed to ballast the lamp. Replacing the lamp with the plasma model, analysis of the ballast is fulfilled. The dimming feature is carried out by pulse-width modulation (PWM) and variable-frequency controls simultaneously. The proposed single-stage ballast is suitable for applications with moderate power level and low-line voltage while requiring a high-output voltage. It can save a controller, an active switch and its driver, reduce size, and possibly increase system reliability while requiring two additional diodes over a conventional two-stage system. A prototype was implemented to verify the theoretical discussion. The hardware measurements have shown that the desired performance can be achieved feasibly.

Wu, T.F.; Yu, T.H.; Chiang, M.C. [National Chung Cheng Univ., Chia-Yi (Taiwan, Province of China)

1998-05-01T23:59:59.000Z

2

Recommendations to the NRC on human engineering guidelines for nuclear power plant maintainability  

SciTech Connect

This document contains human engineering guidelines which can enhance the maintainability of nuclear power plants. The guidelines have been derived from general human engineering design principles, criteria, and data. The guidelines may be applied to existing plants as well as to plants under construction. They apply to nuclear power plant systems, equipment and facilities, as well as to maintenance tools and equipment. The guidelines are grouped into seven categories: accessibility and workspace, physical environment, loads and forces, maintenance facilities, maintenance tools and equipment, operating equipment design, and information needs. Each chapter of the document details specific maintainability problems encountered at nuclear power plants, the safety impact of these problems, and the specific maintainability design guidelines whose application can serve to avoid these problems in new or existing plants.

Badalamente, R.V.; Fecht, B.A.; Blahnik, D.E.; Eklund, J.D.; Hartley, C.S.

1986-03-01T23:59:59.000Z

3

WHY DO TUNA MAINTAIN ELEVATED SLOW MUSCLE TEMPERATURES? POWER OUTPUT OF MUSCLE ISOLATED FROM ENDOTHERMIC AND  

E-Print Network (OSTI)

It has been hypothesised that regional endothermy has evolved in the muscle of some tunas to enhance the locomotory performance of the fish by increasing muscle power output. Using the work loop technique, we have determined the relationship between cycle frequency and power output, over a range of temperatures, in isolated bundles of slow muscle fibres from the endothermic yellowfin tuna (Thunnus albacares) and its ectothermic relative the bonito (Sarda chiliensis). Power output in all preparations was highly temperature-dependent. A counter-current heat exchanger which could maintain a 10 C temperature differential would typically double maximum muscle power output and the frequency at which maximum power is generated (fopt). The deep slow muscle of the tuna was able to operate at higher temperatures than slow muscle from the bonito, but was more sensitive to Summary temperature change than more superficially located slow fibres from both tuna and bonito. This suggests that it has undergone some evolutionary specialisation for operation at higher, but relatively stable, temperatures. fopt of slow muscle was higher than the tailbeat frequency of undisturbed cruising tuna and, together with the high intrinsic power output of the slow muscle mass, suggests that cruising fish have a substantial slow muscle power reserve. This reserve should be sufficient to power significantly higher sustainable swimming speeds, presumably at lower energetic cost than if intrinsically less efficient fast fibres were recruited.

Ectothermic Fish; John D. Altringham; Barbara A. Block

1997-01-01T23:59:59.000Z

4

Microsoft Word - CX-Minidoka-Unity_Wood PoleReplacementFY12_WEB.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

, 2012 , 2012 REPLY TO ATTN OF: KEP-CELILO SUBJECT: Environmental Clearance Memorandum Mark Hadley Lineman Foreman III - TFIF-Idaho Falls Proposed Action: Wood pole replacement along the Minidoka Power House-Unity No. 1 and Unity-Heyburn No. 1, 138-kV transmission line rights-of-way. PP&A Project No.: 2192 Categorical Exclusion Applied (from Subpart D, 10 C.F.R. Part 1021): B1.3 Routine maintenance activities...for structures, rights-of-way, infrastructures such as roads, equipment... routine maintenance activities, corrective....are required to maintain... infrastructures...in a condition suitable for a facility to be used for its designated purpose. Location: The project area is located in Cassia County, Idaho, in Bonneville Power

5

Maintaining electric power system performance: Preparing for the year 2020: Research needs  

DOE Green Energy (OSTI)

The US electric power delivery system will undergo dramatic changes between now and the year 2020. Without an aggressive research and development (R&D) program to develop and integrate new technologies, a substantial mismatch could develop between the system`s performance and the public`s expectations for a stable, reliable source of energy. This report provides a perspective on the future US electrical power delivery system and outlines the major issues for R&D support that will be required to maintain the performance of the system successfully through the year 2020. To define the R&D needs in the electric utility sector, the US Department of Energy (DOE) Office of Energy Management under the Assistant Secretary for Conservation and Renewable Energy, in participation with the Bonneville Power Administration (BPA) and the Western Area Power Administration (WAPA), met with electric utility industry leaders in Denver, Colorado, on March 19 and 20, 1990. The major areas that require increased R&D in order to meet the challenges of system needs by the year 2020 include the following: Effects of exposure to electric and magnetic fields (EMFs), real-time power system control, higher-capacity transmission options, high capacity power electronics, and energy storage. An electric energy delivery system that reliably supplies sufficient electric power at the lowest possible cost to meet the nation`s needs is vital to the economic health of the US. In order to meet the challenges facing the national supply and delivery of electric power in the future, all parties concerned with the R&D of supply and delivery technologies for electric energy must cooperate and must seek to leverage the limited funds available.

Dale, S.J.; Stovall, J.P. [Oak Ridge National Lab., TN (United States); Klein, K.W. [Energetics, Inc., Washington, DC (United States)

1991-11-01T23:59:59.000Z

6

Maintaining electric power system performance: Preparing for the year 2020: Research needs  

DOE Green Energy (OSTI)

The US electric power delivery system will undergo dramatic changes between now and the year 2020. Without an aggressive research and development (R D) program to develop and integrate new technologies, a substantial mismatch could develop between the system's performance and the public's expectations for a stable, reliable source of energy. This report provides a perspective on the future US electrical power delivery system and outlines the major issues for R D support that will be required to maintain the performance of the system successfully through the year 2020. To define the R D needs in the electric utility sector, the US Department of Energy (DOE) Office of Energy Management under the Assistant Secretary for Conservation and Renewable Energy, in participation with the Bonneville Power Administration (BPA) and the Western Area Power Administration (WAPA), met with electric utility industry leaders in Denver, Colorado, on March 19 and 20, 1990. The major areas that require increased R D in order to meet the challenges of system needs by the year 2020 include the following: Effects of exposure to electric and magnetic fields (EMFs), real-time power system control, higher-capacity transmission options, high capacity power electronics, and energy storage. An electric energy delivery system that reliably supplies sufficient electric power at the lowest possible cost to meet the nation's needs is vital to the economic health of the US. In order to meet the challenges facing the national supply and delivery of electric power in the future, all parties concerned with the R D of supply and delivery technologies for electric energy must cooperate and must seek to leverage the limited funds available.

Dale, S.J.; Stovall, J.P. (Oak Ridge National Lab., TN (United States)); Klein, K.W. (Energetics, Inc., Washington, DC (United States))

1991-11-01T23:59:59.000Z

7

Independent transmission system operators and their role in maintaining reliability in a restructured electric power industry  

Science Conference Proceedings (OSTI)

This report summarizes the current status of proposals to form Independent System Operators (ISOs) to operate high-voltage transmission systems in the United States and reviews their potential role in maintaining bulk power system reliability. As background information, the likely new industry structure, nature of deregulated markets, and institutional framework for bulk power system reliability are reviewed. The report identifies issues related to the formation of ISOs and their roles in markets and in reliability, and describes potential policy directions for encouraging the formation of effective ISOs and ensuring bulk system reliability. Two appendices are provided, which address: (1) system operation arrangements in other countries, and (2) summaries of regional U.S. ISO proposals.

NONE

1998-01-01T23:59:59.000Z

8

Radioisotope Power Systems: An Imperative for Maintaining U.S. Leadership in Space Exploration (Free Executive Summary)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Radioisotope Power Systems: An Imperative for Maintaining U.S. Leadership in Space Exploration (Free Executive Summary) Radioisotope Power Systems: An Imperative for Maintaining U.S. Leadership in Space Exploration (Free Executive Summary) http://www.nap.edu/catalog/12653.html Free Executive Summary ISBN: 978-0-309-13857-4, 74 pages, 8 1/2 x 11, paperback (2009) This executive summary plus thousands more available at www.nap.edu. Radioisotope Power Systems: An Imperative for Maintaining U.S. Leadership in Space Exploration Radioisotope Power Systems Committee, National Research Council This free executive summary is provided by the National Academies as part of our mission to educate the world on issues of science, engineering, and health. If you are interested in reading the full book, please visit us online at http://www.nap.edu/catalog/12653.html . You may browse and

9

Control system design for maintaining CO{sub 2} capture in IGCC power plants while loading-following  

SciTech Connect

Load-following requirements for future integrated gasification combined cycle (IGCC) power plants with precombustion CO{sub 2} capture are expected to be far more challenging as electricity produced by renewable energy is connected to the grid and strict environmental limits become mandatory requirements. In this work, loadfollowing studies are performed using a comprehensive dynamic model of an IGCC plant with pre-combustion CO{sub 2} capture developed in Aspen Engineering Suite (AES). Considering multiple single-loop controllers for power demand load following, the preferred IGCC control strategy from the perspective of a power producer is gas turbine (GT) lead with gasifier follow. In this strategy, the GT controls the load by manipulating its firing rate while the slurry feed flow to the gasifier is manipulated to control the syngas pressure at the GT inlet. The syngas pressure control is an integrating process with significant time delay mainly because of the large piping and equipment volumes between the gasifier and the GT inlet. A modified proportionalintegralderivative (PID) control is considered for IGCC syngas pressure control. The desired CO{sub 2} capture rate must be maintained while the IGCC plant follows the load. For maintaining the desired CO{sub 2} capture rate, the control performance of PID control is compared with linear model predictive control (LMPC). The results show that the LMPC outperforms PID control for maintaining CO{sub 2} capture rates in an IGCC power plant while load following.

Bhattacharyya, D.; Turton, R.; Zitney, S.

2012-01-01T23:59:59.000Z

10

Russia: "national subjects" between unity and secession  

Science Conference Proceedings (OSTI)

After the implosion of communism in the USSR (1991) was a real disintegration of the Soviet space, which resulted in five sets geopolitical: Russian Federation, Baltic States, Eastern European States, States Transcaucasian and Central Asian States. In ... Keywords: "national subjects", Russia, democratization, secession, unity

Teodor Simion; Gica Pehoiu; ?tefan Ispas

2010-07-01T23:59:59.000Z

11

Abstract--Wind power generation is growing rapidly. However, maintaining the wind turbine connection to grid is a real  

E-Print Network (OSTI)

induction generator (DFIG). However, no attention has been given to the impact of internal faults) that interface the DFIG with the grid. This paper investigates the impact of the rotor side converter (RSC) IGBT flashover fault on the common coupling (PCC) reactive power and the FRT capability of the DFIG. A proper

Pota, Himanshu Roy

12

Developing and Maintaining a Master Equipment List for Fossil Power Plants: Asset Naming Conventions, Classifications and Hierarchies  

Science Conference Proceedings (OSTI)

As electric generating utilities built their fleets in the United States,it was not uncommon for different architectural engineering firms todesign and build the various power plants within the fleets. Thisoften resulted in several inconsistencies across the fleet related todrawing and design documentation and information regardingsystems and components. Essentially, each plant would become itsown entity and have the responsibility of developing and ...

2012-12-26T23:59:59.000Z

13

Safety System Obsolescence and Maintainability  

Science Conference Proceedings (OSTI)

The nuclear power industry is currently facing increasing obsolescence issues with original instrumentation and control (I&C) equipment, particularly in safety system applications. These systems, often more than thirty years old, are based on analog technology, relays, and other discrete components, which are becoming difficult to maintain and replace with like equipment. This report helps utilities understand their options and choose the most cost-effective strategies for maintaining and replacing obsol...

2001-05-02T23:59:59.000Z

14

V-085: Cisco Unity Express Input Validation Hole Permits Cross-Site Request  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5: Cisco Unity Express Input Validation Hole Permits Cross-Site 5: Cisco Unity Express Input Validation Hole Permits Cross-Site Request Forgery Attacks V-085: Cisco Unity Express Input Validation Hole Permits Cross-Site Request Forgery Attacks February 6, 2013 - 1:06am Addthis PROBLEM: Cisco Unity Express Input Validation Hole Permits Cross-Site Request Forgery Attacks PLATFORM: Cisco Unity Express prior to 8.0 ABSTRACT: A vulnerability was reported in Cisco Unity Express. REFERENCE LINKS: Cisco Security Notice SecurityTracker Alert ID: 1028075 CVE-2013-1120 IMPACT ASSESSMENT: Medium DISCUSSION: Cisco Unity Express software prior to version 8.0 contains vulnerabilities that could allow an unauthenticated, remote attacker to conduct cross site request forgery attacks. The vulnerabilities are due to insufficient input validation. An attacker could exploit these vulnerabilities by

15

Reliability and maintainability program  

SciTech Connect

The program's goals are to accelerate the adoption of active solar energy systems in building applications by improving the reliability and maintainability of installed systems. The project is designed to accomplish this by providing the latest information; by assisting the industry in improving reliability and maintainability; by assisting in design, manufacture, installation and maintenance of reliable and durable systems; and by assisting in the development of codes and standards. Work and accomplishments in these areas are enumerated. (LEW)

Eden, A.

1981-05-01T23:59:59.000Z

16

Apparatus for establishing and maintaining a stable discharge across a stream of flowing gas, particularly useful for high-power lasers  

SciTech Connect

Apparatus is described for establishing and maintaining a stable discharge across a stream of gas flowing through a gas-flow channel, which consists of: an electrode system including a group of working electrodes disposed on opposite sides of the gas flow channel and spaced longitudinally thereof in the direction of gas flow, which working electrodes include at least one upstream electrode at the upstream end of the gas flow channel; a high-voltage alternating current source connected at one side to each of the working electrodes and at the opposite side to a point of fixed reference potential; and a ballast impedance connected to each of the working electrodes for stabilizing the electrical discharge; the electrode system further including at least one starting electrode adjacent to the upstream working electrode and connected to the point of fixed reference potential via a ballast impedance of substantially larger impedance value than those connected to the working electrodes, such that the starting electrode is effective to bring the point of fixed reference potential to the upstream working electrode to start the discharge, and to draw little current after the discharge has been started.

Katz, D.

1986-03-04T23:59:59.000Z

17

Maintaining body temperature  

NLE Websites -- All DOE Office Websites (Extended Search)

Maintaining body temperature Maintaining body temperature Name: Jeff Location: N/A Country: N/A Date: N/A Question: What keeps the human body at a constant temperature of 98.6? Replies: Maintaining body temperature is very complex. It also takes a lot of energy. About 80% of the energy from the food you eat goes to maintaining body temperature. Basically, the chemical reactions of metabolism of stored food, especially fats, generate heat as a by product. This heat warms the body. The brain reads temperature and controls to some extent the rate of this metabolism. There are also many other mechanisms triggered by the brain to keep the core of your body warm, even if the periphery (skin) is cold. Blood vessels to the fingers and toes constrict, so that the cold air doesn't cool the blood too much, so that cooled blood doesn't cool down the heart and brain when it returns. In severe cases, your body will sacrifice a finger or a toe to keep you from dying of cold core temperature (frostbite: it saves your life!). Also the brain can order a lot of muscles to contract rapidly. This generates a lot of heat quickly, a response called shivering. There's much more to this exciting field of research.

18

Fusion Rules of the Lowest Weight Representations of osp_q(1|2) at Roots of Unity: Polynomial Realization and Degeneration at Roots of Unity  

E-Print Network (OSTI)

The degeneracy of the lowest weight representations of the quantum superalgebra $osp_q(1|2)$ and their tensor products at exceptional values of %when deformation parameter $q$ takes exceptional values is studied. The main features of the structures of the finite dimensional lowest weight representations and their fusion rules are illustrated using realization of group generators as finite-difference operators acting in the space of the polynomials. The complete fusion rules for the decompositions of the tensor products at roots of unity are presented. The appearance of indecomposable representations in the fusions is described using Clebsh-Gordan coefficients derived for general values of $q$ and at roots of unity.

D. Karakhanyan; Sh. Khachatryan

2006-02-08T23:59:59.000Z

19

Maintaining plant safety margins  

SciTech Connect

The Final Safety Analysis Report Forms the basis of demonstrating that the plant can operate safely and meet all applicable acceptance criteria. In order to assure that this continues through each operating cycle, the safety analysis is reexamined for each reload core. Operating limits are set for each reload core to assure that safety limits and applicable acceptance criteria are not exceeded for postulated events within the design basis. These operating limits form the basis for plant operation, providing barriers on various measurable parameters. The barriers are refereed to as limiting conditions for operation (LCO). The operating limits, being influenced by many factors, can change significantly from cycle to cycle. In order to be successful in demonstrating safe operation for each reload core (with adequate operating margin), it is necessary to continue to focus on ways to maintain/improve existing safety margins. Existing safety margins are a function of the plant type (boiling water reactor/pressurized water reactor (BWR/PWR)), nuclear system supply (NSSS) vendor, operating license date, core design features, plant design features, licensing history, and analytical methods used in the safety analysis. This paper summarizes the experience at Yankee Atomic Electric Company (YAEC) in its efforts to provide adequate operating margin for the plants that it supports.

Bergeron, P.A.

1989-01-01T23:59:59.000Z

20

A q-Virasoro Algebra at roots of unity, Free Fermions and Temperley Lieb Hamiltonians  

E-Print Network (OSTI)

In this work we introduce a novel q-deformation of the Virasoro algebra expressed in terms of free fermions, we then realize that this algebra, when the deformation parameter is a root of unity can be realized exactly on the lattice. We then study the relations existing between this lattice deformed Virasoro algebra at roots of unity and the tower of commuting Temperley-Lieb hamiltonians introduced in a previous work.

Alessandro Nigro

2012-11-05T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Indonesian drilling maintains steady pace  

SciTech Connect

Offshore drilling activity in Indonesia increased nominally the first quarter of 1985 to an average 29 rigs. Barring any further problems with oil prices and markets, operators are expected to maintain essentially the current general level of appraisal/development work for the rest of this year. There are still a number of prospective regions to be explored in Southeast Asia. Regional developments are described for the South China Sea area, the Java Sea, South Sumatra, Kalimantan, Irian Jaya and the Malacca Strait.

Not Available

1985-05-01T23:59:59.000Z

22

Derivation of conditions for a Brans-Dicke coupling constant of order unity be consistent with solar system bounds  

E-Print Network (OSTI)

We provide proofs of some assumptions recently made by F. O. Minotti to conclude on the possibility that an additional scalar field minimally coupled to gravity may help to reconcile a Brans-Dicke coupling constant $\\omega$ of the order unity with solar system bounds.

Mbelek, Jean Paul

2013-01-01T23:59:59.000Z

23

Derivation of conditions for a Brans-Dicke coupling constant of order unity be consistent with solar system bounds  

E-Print Network (OSTI)

We provide proofs of some assumptions recently made by F. O. Minotti to conclude on the possibility that an additional scalar field minimally coupled to gravity may help to reconcile a Brans-Dicke coupling constant $\\omega$ of the order unity with solar system bounds.

Jean Paul Mbelek

2013-04-30T23:59:59.000Z

24

The Dynamic Utilization of Substation Measurements to Maintain Power System  

E-Print Network (OSTI)

engineering), except for the mineral extraction criteria, they contribute to more than 50% to the substation to Aluminium Electrolysis Conversion Substations François Cluzel1* , Dominique Millet2 , Yann Leroy1 or energy mix). Two cases studies concerning AREVA T&D's aluminium electrolysis conversion substations

Kezunovic, Mladen

25

Maintaining DOE Technical Standards, TSPP-7  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7-2013 7-2013 DOE TECHNICAL STANDARDS September 2013 PROGRAM PROCEDURES MAINTAINING DOE TECHNICAL STANDARDS U.S. Department of Energy Office of Nuclear Safety Washington, D.C. 20585 DOE-TSPP-7-2013 Maintaining September 2013 DOE Technical Standards Program CONTENTS 1. SCOPE ............................................................................................................................................ 1 1.1 Purpose ....................................................................................................................... 1 1.2 Applicability ................................................................................................................. 1 2. DOCUMENT MAINTENANCE ....................................................................................................... 1

26

Encapsulation method for maintaining biodecontamination activity  

DOE Patents (OSTI)

A method for maintaining the viability and subsequent activity of microorganisms utilized in a variety of environments to promote biodecontamination of surfaces. One application involves the decontamination of concrete surfaces. Encapsulation of microbial influenced degradation (MID) microorganisms has shown that MID activity is effectively maintained under passive conditions, that is, without manual addition of moisture or nutrients, for an extended period of time.

Rogers, Robert D. (Idaho Falls, ID); Hamilton, Melinda A. (Idaho Falls, ID); Nelson, Lee O. (Idaho Falls, ID); Benson, Jennifer (Cockermouth, GB); Green, Martin J. (Wooton, GB); Milner, Timothy N. (Centerville, VA)

2002-01-01T23:59:59.000Z

27

Maintaining Your Air Conditioner | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maintaining Your Air Conditioner Maintaining Your Air Conditioner Maintaining Your Air Conditioner June 18, 2013 - 6:20pm Addthis Replacing or cleaning air conditioner filters is a critical maintenance task. | Photo courtesy of ©iStockphoto/firemanYU. Replacing or cleaning air conditioner filters is a critical maintenance task. | Photo courtesy of ©iStockphoto/firemanYU. What does this mean for me? Regular maintenance keeps your air conditioner running as efficiently as possible. Maintaining your air conditioner will save you money by extending the unit's life. An air conditioner's filters, coils, and fins require regular maintenance for the unit to function effectively and efficiently throughout its years of service. Neglecting necessary maintenance ensures a steady decline in air conditioning performance while energy use steadily increases.

28

Human Engineering Design Guidelines for Maintainability  

Science Conference Proceedings (OSTI)

Utility managers, designers, and engineers can now systematically incorporate appropriate human factors engineering principles and criteria for maintainability into new plant designs or existing plant modifications. Using these guidelines can also result in increased productivity, safety, and plant availability.

1985-12-01T23:59:59.000Z

29

Maintaining Your Air Conditioner | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maintaining Your Air Conditioner Maintaining Your Air Conditioner Maintaining Your Air Conditioner June 18, 2013 - 6:20pm Addthis Replacing or cleaning air conditioner filters is a critical maintenance task. | Photo courtesy of ©iStockphoto/firemanYU. Replacing or cleaning air conditioner filters is a critical maintenance task. | Photo courtesy of ©iStockphoto/firemanYU. What does this mean for me? Regular maintenance keeps your air conditioner running as efficiently as possible. Maintaining your air conditioner will save you money by extending the unit's life. An air conditioner's filters, coils, and fins require regular maintenance for the unit to function effectively and efficiently throughout its years of service. Neglecting necessary maintenance ensures a steady decline in air conditioning performance while energy use steadily increases.

30

The Probability Distribution of Wind Power From a Dispersed Array of Wind Turbine Generators  

Science Conference Proceedings (OSTI)

A method is presented for estimating the probability distribution of wind power from a dispersed array of wind turbine sites where the correlation between wind speeds at distinct sites is less than unity. The distribution is obtained from a model ...

John Carlin; John Haslett

1982-03-01T23:59:59.000Z

31

Reliability and maintainability seminar: summary of proceedings  

DOE Green Energy (OSTI)

The following are described briefly: Overview of the Federal Reliability and Maintainability Program Plan, Summary of Proceedngs, Overview of Southern Solar Energy Center Programs, and Solar Domestic Hot Water Design Guidelines Handbook. Also included are the Seminar Agenda and the list of Seminar Attendees. (MHR)

Beek, C.R.

1981-04-01T23:59:59.000Z

32

Guidelines for Maintaining Steam Turbine Lubrication Systems  

Science Conference Proceedings (OSTI)

Failures of steam turbine bearings and rotors cost the utility industry an estimated $150 million a year. A third of these failures involve contaminated lubricants or malfunctioning lubricant supply system components. This report, outlining a comprehensive surveillance program, presents guidelines for maintaining major elements in the turbine lubrication system.

1986-07-01T23:59:59.000Z

33

Maintaining ideal body weight counseling sessions  

SciTech Connect

The purpose of this program is to provide employees with the motivation, knowledge and skills necessary to maintain ideal body weight throughout life. The target audience for this program, which is conducted in an industrial setting, is the employee 40 years of age or younger who is at or near his/her ideal body weight.

Brammer, S.H.

1980-10-09T23:59:59.000Z

34

On-line reactive power compensation schemes for unbalanced three phase four wire distribution feeders  

Science Conference Proceedings (OSTI)

A new reactive power compensation method is developed to reduce the negative and zero sequence components of load currents and to improve the load bus power factor of unbalanced three-phase four-wire distribution feeders. Negative and zero sequences currents may cause additional losses and damages to power systems. Load compensation at the load bus is an effective method to eliminate those undesired sequence currents. The compensation technique uses a Y-connected and a [Delta]-connected static reactive power compensators to give a different amount of reactive power compensation to each phase. The compensation formulas are very suitable for on-line control by measuring phase voltages and currents in the real time. The compensation effect can also be achieved even if one leg of the SVCs is out of service. In addition to balancing effect and power factor improvement at the load bus, the SVCs can also be used to support the load bus voltage and to maintain the substation feeder at unity powder factor. Digital simulations are made with the load data measured from an 11.4kV secondary substation feeder.

Sanyi Lee; Chijui Wu (National Taiwan Inst. of Tech., Taipei (Taiwan, Province of China). Dept. of Electrical Engineering)

1993-10-01T23:59:59.000Z

35

Study the power flow control of a power system with unified power flow controller.  

E-Print Network (OSTI)

??Electrical power systems is a large interconnected network that requires a careful design to maintain the system with continuous power flow operation without any limitations. (more)

Peesari, Vakula

2010-01-01T23:59:59.000Z

36

Categorical Exclusion Determinations: Bonneville Power Administration |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

February 6, 2012 February 6, 2012 CX-007997: Categorical Exclusion Determination Grant Consumer Power, Incorporated's Request for use of Right-of-way at Harrisburg Substation CX(s) Applied: B4.9 Date: 02/06/2012 Location(s): Oregon Offices(s): Bonneville Power Administration February 2, 2012 CX-007999: Categorical Exclusion Determination Wood Pole Replacement Along the Minidoka Power House-Unity #1 and Unity-Heyburn #1, 138-Kilovolt Transmission Line Rights-of-way CX(s) Applied: B1.3 Date: 02/02/2012 Location(s): Idaho Offices(s): Bonneville Power Administration February 2, 2012 CX-007998: Categorical Exclusion Determination Integration of Stoltze Land and Lumber Biomass Generation CX(s) Applied: B1.7 Date: 02/02/2012 Location(s): Montana Offices(s): Bonneville Power Administration

37

EnergySmart Schools Tips: Retrofitting, Operating, and Maintaining...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EnergySmart Schools Tips: Retrofitting, Operating, and Maintaining Existing Buildings EnergySmart Schools Tips: Retrofitting, Operating, and Maintaining Existing Buildings An...

38

Maintaining Quality in a Decommissioning Environment  

Science Conference Proceedings (OSTI)

The decommissioning of AECL's Whiteshell Laboratories is Canada's largest nuclear decommissioning project to date. This research laboratory has operated for forty years since it was set up in 1963 in eastern Manitoba as the Whiteshell Nuclear Research Establishment, complete with 60 MW(Th) test reactor, hot cells, particle accelerators, and multiple large-scale research programs. Returning the site to almost complete green state will require several decades of steady work in combination with periods of storage-with-surveillance. In this paper our approach to maintaining quality during the long decommissioning period is explained. In this context, 'quality' includes both regulatory aspects (compliance with required standards) and business aspects (meeting the customers' needs and exceeding their expectations). Both aspects are discussed, including examples and lessons learned. The five years of development and implementation of a quality assurance program for decommissioning the WL site have led to a number of lessons learned. Many of these are also relevant to other decommissioning projects, in Canada and elsewhere: - Early discussions with the regulator can save time and effort later in the process; - An iterative process in developing documentation allows for steady improvements and input throughout the process; - Consistent 2-way communication with staff regarding the benefits of a quality program assists greatly in adoption of the philosophy and procedures; - Top-level management must lead in promoting quality; - Field trials of procedures ('beta testing') ensures they are easy to use as well as useful. Success in decommissioning the Whiteshell Laboratories depends on the successful implementation of a rigorous quality program. This will help to ensure both safety and efficiency of all activities on site, from planning through execution and reporting. The many aspects of maintaining this program will continue to occupy quality practitioners in AECL, reaping steady benefits to AECL and to its customers, the people of Canada.

Attas, Michael [Atomic Energy of Canada Limited, Whiteshell Laboratories, Pinawa, Manitoba, R0E 1L0 (Canada)

2008-01-15T23:59:59.000Z

39

Reliability and Maintainability Issues for the Next Linear Collider  

Science Conference Proceedings (OSTI)

Large accelerators for high energy physics research traditionally have been designed using informal best design, engineering, and management practices to achieve acceptable levels of operational availability. However, the Next Linear Collider(NLC) project presents a particular challenge for operational availability due to the unprecedented size and complexity of the accelerator systems required to achieve the physics goals of high center-of-mass energy and high luminosity. Formal reliability and maintainability analysis, design, and implementation will be required to achieve acceptable operational availability for the high energy physics research program. This paper introduces some of the basic concepts of reliability analysis and applies them to the 2.6-cm microwave power system of the two 10-km-long, 250-GeV linacs that are currently proposed for the NLC design.

Wilson, Zane J.; Gold, Saul L.; Koontz, Ron F.; Lavine, Ted L.; /SLAC

2011-08-26T23:59:59.000Z

40

Guide to Operating and Maintaining EnergySmart Schools | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Guide to Operating and Maintaining EnergySmart Schools Guide to Operating and Maintaining EnergySmart Schools This guide is a primary resource for developing and implementing a...

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Y-12 Construction maintains 'superb' safety performance | Y-12...  

NLE Websites -- All DOE Office Websites (Extended Search)

Construction maintains ... Y-12 Construction maintains 'superb' safety performance Posted: March 6, 2013 - 6:03pm Tom Morris, B&W Y-12 vice president of projects, presents...

42

Onsite Wastewater Treatment Systems: Understanding and Maintaining your Septic System  

E-Print Network (OSTI)

It is important that homeowners maintain their septic systems properly. Otherwise, problems that develop could threaten human health and the environment. In this publication you will learn how to maintain all the components of a septic system. There are checklists to remind you of important steps in maintaining the safety and integrity of your system.

Lesikar, Bruce J.; Mechell, Justin; Alexander, Rachel

2008-10-23T23:59:59.000Z

43

PP-234 Baja California Power Inc | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

234 Baja California Power Inc PP-234 Baja California Power Inc Presidential permit authorizing Baja California Power Inc to construct, operate, and maintain electric transmission...

44

PP-64 Basin Electric Power Cooperative | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 Basin Electric Power Cooperative PP-64 Basin Electric Power Cooperative Presidential Permit Authorizing Basin Electric Power Cooperative to construct, operate, and maintain...

45

PP-43 Maine Electric Power Company, Inc. | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 Maine Electric Power Company, Inc. PP-43 Maine Electric Power Company, Inc. Presidential Permit authorizing Maine Electric Power Company, Inc. to construct, operate, and maintain...

46

PP-94 Central Power & Light Company | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 Central Power & Light Company PP-94 Central Power & Light Company Presidental Permit authorizing Central Power & Light Company to construct, operate, and maintain electric...

47

PP-219 Central Power and Light Company | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

19 Central Power and Light Company PP-219 Central Power and Light Company Presidential permit authorizing Central Power and Light Company to construct, operate, and maintain...

48

PP-78 Minnesota Power & Light Company | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 Minnesota Power & Light Company PP-78 Minnesota Power & Light Company Presidential Permit authorizing Minnesota Power & Light Company to construct, operate, and maintain electric...

49

PP-6 Puget Sound Power & Light Company | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Puget Sound Power & Light Company PP-6 Puget Sound Power & Light Company Presidential permit authorizing Puget Sound Power & Light Company to construct, operate, and maintain...

50

PP-61 Minnkota Power Cooperative (MPC) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 Minnkota Power Cooperative (MPC) PP-61 Minnkota Power Cooperative (MPC) Presidential Permit authorizing Minnkota Power Cooperative (MPC) to construct, operate, and maintain...

51

Operating and Maintaining Your Heat Pump | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Operating and Maintaining Your Heat Pump Operating and Maintaining Your Heat Pump Operating and Maintaining Your Heat Pump June 24, 2012 - 3:22pm Addthis Changing filters regularly is an important part of maintaining a heat pump system. | Photo courtesy of ©iStockphoto/BanksPhotos Changing filters regularly is an important part of maintaining a heat pump system. | Photo courtesy of ©iStockphoto/BanksPhotos What does this mean for me? Learn to operate and maintain your heat pump system properly to maximize energy and money savings. You can do many operational and maintenance tasks yourself. Proper operation of your heat pump will save energy. Do not set back the heat pump's thermostat if it causes the backup heating to come on -- backup heating systems are usually more expensive to operate. Continuous indoor

52

Optimizing Power Factor Correction  

E-Print Network (OSTI)

The optimal investment for power factor correcting capacitors for Kansas Power and Light Company large power contract customers is studied. Since the billing capacity is determined by dividing the real demand by the power factor (the minimum billing capacity is based on 80 percent of the summer peak billing capacity) and the billing capacity is used to determine the number of kilowatt-hours billed at each pricing tier, the power factor affects both the demand and the energy charge. There is almost no information available in the literature concerning recommended power factor corrections for this situation. The general advice commonly given in the past has been that power factor should be corrected to above 0.9 if it is below that value to begin with, but that does not take into account the facts of the situation studied here. Calculations relevant to a commercial consumer of electricity were made for demands of 200, 400, 800, 1,600, 3,200, and 6,400 kW and monthly energy consumption periods of 100, 150, 200, 300, 400, and 500 hours for several capacitor purchase and installation costs. The results are displayed in a series of graphs that enable annual cost savings and payback periods to be readily determined over a range of commonly encountered parameter values. It is found that it is often economically advantageous to correct a power factor to near unity.

Phillips, R. K.; Burmeister, L. C.

1986-06-01T23:59:59.000Z

53

The Primary Standards Laboratory (PSL) maintains a wide variety...  

NLE Websites -- All DOE Office Websites (Extended Search)

Nuclear Security Administration under contract DE-AC04-94AL85000. The Primary Standards Laboratory (PSL) maintains a wide variety of primary thermometry standards to assure...

54

The Primary Standards Laboratory (PSL) maintains a wide variety...  

NLE Websites -- All DOE Office Websites (Extended Search)

Nuclear Security Administration under contract DE-AC04-94AL85000. The Primary Standards Laboratory (PSL) maintains a wide variety of primary standards to assure accurate...

55

The Primary Standards Laboratory (PSL) maintains a wide variety...  

NLE Websites -- All DOE Office Websites (Extended Search)

Nuclear Security Administration under contract DE-AC04-94AL85000. The Primary Standards Laboratory (PSL) maintains a wide variety of primary acceleration and shock...

56

Maintaining History of the ARM Climate Research Facility Data  

NLE Websites -- All DOE Office Websites (Extended Search)

Maintaining History of the ARM Climate Research Facility Data Koontz, Annette Pacific Northwest National Laboratory Sivaraman, Chitra Pacific Northwest National Laboratory Martin,...

57

Section_201_Establishing_Maintaining_and_Deactivating_Limited...  

NLE Websites -- All DOE Office Websites (Extended Search)

201 Establishing, Maintaining, and Deactivating Limited Areas and Vault-Type Rooms Description Classified matter must be processed, discussed, handled, or stored in designated...

58

Partition-of-unity finite-element method for large scale quantum molecular dynamics on massively parallel computational platforms  

Science Conference Proceedings (OSTI)

Over the course of the past two decades, quantum mechanical calculations have emerged as a key component of modern materials research. However, the solution of the required quantum mechanical equations is a formidable task and this has severely limited the range of materials systems which can be investigated by such accurate, quantum mechanical means. The current state of the art for large-scale quantum simulations is the planewave (PW) method, as implemented in now ubiquitous VASP, ABINIT, and QBox codes, among many others. However, since the PW method uses a global Fourier basis, with strictly uniform resolution at all points in space, and in which every basis function overlaps every other at every point, it suffers from substantial inefficiencies in calculations involving atoms with localized states, such as first-row and transition-metal atoms, and requires substantial nonlocal communications in parallel implementations, placing critical limits on scalability. In recent years, real-space methods such as finite-differences (FD) and finite-elements (FE) have been developed to address these deficiencies by reformulating the required quantum mechanical equations in a strictly local representation. However, while addressing both resolution and parallel-communications problems, such local real-space approaches have been plagued by one key disadvantage relative to planewaves: excessive degrees of freedom (grid points, basis functions) needed to achieve the required accuracies. And so, despite critical limitations, the PW method remains the standard today. In this work, we show for the first time that this key remaining disadvantage of real-space methods can in fact be overcome: by building known atomic physics into the solution process using modern partition-of-unity (PU) techniques in finite element analysis. Indeed, our results show order-of-magnitude reductions in basis size relative to state-of-the-art planewave based methods. The method developed here is completely general, applicable to any crystal symmetry and to both metals and insulators alike. We have developed and implemented a full self-consistent Kohn-Sham method, including both total energies and forces for molecular dynamics, and developed a full MPI parallel implementation for large-scale calculations. We have applied the method to the gamut of physical systems, from simple insulating systems with light atoms to complex d- and f-electron systems, requiring large numbers of atomic-orbital enrichments. In every case, the new PU FE method attained the required accuracies with substantially fewer degrees of freedom, typically by an order of magnitude or more, than the current state-of-the-art PW method. Finally, our initial MPI implementation has shown excellent parallel scaling of the most time-critical parts of the code up to 1728 processors, with clear indications of what will be required to achieve comparable scaling for the rest. Having shown that the key remaining disadvantage of real-space methods can in fact be overcome, the work has attracted significant attention: with sixteen invited talks, both domestic and international, so far; two papers published and another in preparation; and three new university and/or national laboratory collaborations, securing external funding to pursue a number of related research directions. Having demonstrated the proof of principle, work now centers on the necessary extensions and optimizations required to bring the prototype method and code delivered here to production applications.

Pask, J E; Sukumar, N; Guney, M; Hu, W

2011-02-28T23:59:59.000Z

59

The Primary Standards Laboratory (PSL) maintains a wide variety...  

NLE Websites -- All DOE Office Websites (Extended Search)

a variety of measurement systems, including four Vector Network Analyzers (VNAs), a power standard calibration system and a power meter calibration system. Capabilities Below...

60

The Primary Standards Laboratory (PSL) maintains a wide variety...  

NLE Websites -- All DOE Office Websites (Extended Search)

Nuclear Security Administration under contract DE-AC04-94AL85000. The Primary Standards Laboratory (PSL) maintains a variety of primary mass and force standards to assure...

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

The Primary Standards Laboratory (PSL) maintains a wide variety...  

NLE Websites -- All DOE Office Websites (Extended Search)

National Nuclear Security Administration under contract DE-AC04-94AL85000 The Primary Standards Laboratory (PSL) maintains a variety of primary optical standards to assure accurate...

62

The Primary Standards Laboratory (PSL) maintains a wide variety...  

NLE Websites -- All DOE Office Websites (Extended Search)

for the US Department of Energy under contract DE-ACO4-94AL85000. The Primary Standards Laboratory (PSL) and Sandia's Radiation Protection organization maintain a variety...

63

Installing and Maintaining a Small Wind Electric System | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Installing and Maintaining a Small Wind Electric System Installing and Maintaining a Small Wind Electric System Installing and Maintaining a Small Wind Electric System July 2, 2012 - 8:22pm Addthis Installing and Maintaining a Small Wind Electric System What does this mean for me? When installing a wind system, the location of the system, the energy budget for the site, the size of the system, and the height of the tower are important elements to consider. Deciding whether to connect the system to the electric grid or not is also an important decision. If you went through the planning steps to evaluate whether a small wind electric system will work at your location, you will already have a general idea about: The amount of wind at your site The zoning requirements and covenants in your area The economics, payback, and incentives of installing a wind system

64

Weatherization Assistance for Low-Income Persons: Maintaining the Privacy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Weatherization Assistance for Low-Income Persons: Maintaining the Weatherization Assistance for Low-Income Persons: Maintaining the Privacy of Applicants for and Recipients of Services Weatherization Assistance for Low-Income Persons: Maintaining the Privacy of Applicants for and Recipients of Services Amending regulations to require all States and other service providers that participate in the Weatherization Assistance Program (WAP) to treat all requests for information concerning applicants and recipients of WAP funds in a manner consistent with the Federal government's treatment of information requested under the Freedom of Information Act (FOIA), 5 U.S.C. 552, including the privacy protections contained in Exemption (b)(6) of the FOIA, 5 U.S.C. 552(b)(6). Weatherization Assistance for Low-Income Persons: Maintaining the Privacy

65

Method of and apparatus for enabling output power of solar panel to be maximized  

SciTech Connect

The D.C. Power supplied by a photovoltaic solar panel to a load is controlled by monitoring the slope of the panel voltage vs. Current characteristic and adjusting the current supplied by the panel to the load so that the slope is approximately unity. The slope is monitored by incrementally changing the panel load and indicating whether the resulting change in current derived from the panel is above or below a reference value, indicative of the panel voltage. In response to the change in the monitored current being above the reference value, the slope of a voltage vs. Current curve is greater than unity and the load is adjusted to decrease the current supplied by the panel to the load. Conversely, in response to the current being less than the reference value, the slope of the voltage vs. Current curve is less than unity and the load is adjusted to increase the current supplied by the panel to the load.

Baker, R.H.

1983-03-01T23:59:59.000Z

66

New optimization techniques for power system generation scheduling.  

E-Print Network (OSTI)

??Generation scheduling in restructured electric power systems is critical to maintain the stability and security of a power system and economical operation of the electricity (more)

Sun, Wei

2011-01-01T23:59:59.000Z

67

Installing and Maintaining a Home Solar Electric System | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Installing and Maintaining a Home Solar Electric System Installing and Maintaining a Home Solar Electric System Installing and Maintaining a Home Solar Electric System July 2, 2012 - 8:21pm Addthis When choosing a contractor, ask about their work record, experience, and licenses, and get more than one bid for the installation of your PV system. | Photo courtesy of Dennis Schroeder, NREL. When choosing a contractor, ask about their work record, experience, and licenses, and get more than one bid for the installation of your PV system. | Photo courtesy of Dennis Schroeder, NREL. How does it work? Making sure your home solar electric or PV system is sized, sited, and installed correctly is essential for maximizing its energy performance. As with any mechanical or electrical appliance, PV systems require routine, periodic maintenance.

68

Installing and Maintaining a Home Solar Electric System | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Installing and Maintaining a Home Solar Electric System Installing and Maintaining a Home Solar Electric System Installing and Maintaining a Home Solar Electric System July 2, 2012 - 8:21pm Addthis When choosing a contractor, ask about their work record, experience, and licenses, and get more than one bid for the installation of your PV system. | Photo courtesy of Dennis Schroeder, NREL. When choosing a contractor, ask about their work record, experience, and licenses, and get more than one bid for the installation of your PV system. | Photo courtesy of Dennis Schroeder, NREL. How does it work? Making sure your home solar electric or PV system is sized, sited, and installed correctly is essential for maximizing its energy performance. As with any mechanical or electrical appliance, PV systems require routine, periodic maintenance.

69

Continuous-wave parametric oscillation in polarisation-maintaining optical fibre  

SciTech Connect

Continuous-wave parametric oscillation in a polarisation-maintaining optical fibre has been achieved for the first time using polarisation phase matching. Up-conversion with a frequency shift of {approx}8.6 THz has been demonstrated experimentally. The single-pass optical power generated at 1017 nm in a 85-m-long Nufern PM980-XP fibre exceeded 40 mW. The conversion efficiency was 3.3%, which is an order of magnitude higher than that reported previously for cw parametric up-conversion in the 1-{mu}m spectral region. We compare theoretical predictions with experimental data and analyse factors that may influence output power saturation with increasing signal and pump powers.

Zlobina, E A; Kablukov, S I; Babin, Sergei A [Institute of Automation and Electrometry, Siberian Branch, Russian Academy of Sciences, Novosibirsk (Russian Federation)

2011-09-30T23:59:59.000Z

70

PP-61-1 Minnkota Power Cooperative (MPC) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1-1 Minnkota Power Cooperative (MPC) PP-61-1 Minnkota Power Cooperative (MPC) Presidential Permit authorizing Minnkota Power Cooperative (MPC) to construct, operate, and maintain...

71

Guide to Operating and Maintaining EnergySmart Schools  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Operating Operating and Maintaining EnergySmart Schools ACKNOWLEDGMENTS The U.S. Department of Energy would like to thank the Council of Educational Facility Planners International (CEFPI) for assisting in the development of this guide as a participating sponsor. DOE also acknowledges the invaluable contributions of the working group members and case study subjects listed on the inside back cover. This constructive and informative document would not have been possible without their active engagement. Guide to Operating and Maintaining EnergySmart Schools Table of Contents Executive Summary & Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Chapter 1. Identifying Energy Savings and Getting Started. . . . . . . . . . . . . . . . .

72

Fuel Cells for Backup Power in Telecommunications Facilities (Fact Sheet)  

DOE Green Energy (OSTI)

Telecommunications providers rely on backup power to maintain a constant power supply, to prevent power outages, and to ensure the operability of cell towers, equipment, and networks. The backup power supply that best meets these objectives is fuel cell technology.

Not Available

2009-04-01T23:59:59.000Z

73

Specification for Brayton Isotope Power System (BIPS) electrical output power characteristics  

SciTech Connect

The specification defines the Brayton Isotope Power System (BIPS) standards and characteristics for electrical power generation required to be maintained at utilizing equipments power-input terminals during generation and distribution.

Post, P

1976-06-20T23:59:59.000Z

74

The Role of Filtration in Maintaining Clean Heat Exchanger Coils  

SciTech Connect

The main purpose of the study was to investigate the role of filtration in maintaining clean heat exchanger coils and overall performance. Combinations of 6 different levels of filtration (MERV 14, 11, 8, 6, 4, and no filter) and 4 different coils (an eight-row lanced-fin coil, HX8L), (an eight-row wavy-fin coil, HX8W), (a four-row lanced-fin coil, HX4L) and (a two-row lanced-fin coil, HX2L) were tested at 4 different air velocities (1.52, 2.03, 2.54,3.05 m/s (300, 400, 500, 600 ft/min)). The fouled conditions were obtained after injection of 600 grams of ASHRAE standard dust upstream of the filter/coil combination. This magnitude of dust is representative of a year of normal operation for an air conditioning system. The air-side pressure drops of the coils and filters and air-side heat transfer coefficients of the coils were determined from the measurements under the clean and fouled conditions. Depending upon the filter and coil test, the coil pressure drops increased in the range of 6%-30% for an air velocity at 2.54 m/s (500 ft/min). The impact was significantly greater for tests performed without a filter. The largest relative effect of fouling on pressure drop occurs for coils with fewer rows and having lanced fins. Coils with a greater number of rows can hold more dust so that a fixed amount of dust has a relatively smaller impact. The impact of fouling on air-side heat transfer coefficients was found to be relatively small. In some cases, heat transfer was actually enhanced due to additional turbulence caused by the presence of dust. The experimental results for pressure drops and heat transfer coefficients were correlated and the correlations were implemented within computer models of prototypical rooftop air conditioners and used to evaluate the impact of fouling on cooling capacity and EER. The equipment cooling capacity is reduced with fouling primarily because of a decrease in air flow due to the increase pressure drop rather than due to changes in h eat transfer coefficient. In most cases, the EER was reduced with fouling primarily due to increased fan power. However, the changes in EER were relatively small, in the range of 1%-9% (10%). For most cases, equipment having low efficiency filters had higher EER after fouling than equipment with high efficiency filters, because the high efficiency filter caused significantly higher pressure drops than the low efficiency filters. The extra filter pressure drop outweighed the reduced coil pressure drop after fouling. The impact of fan efficiency curves was also investigated in the study. The energy penalty associated with high efficiency filters was reduced considerably with higher efficiency fans. There is an energy penalty associated with the use of high efficiency filtration. However, the primary reason for selecting high efficiency filters for a particular application would be improved air quality. For HX8L, the quantity of dust passing through the coil with a MERV4 filter was approximately 30 times the dust passing the coil with a MERV14 filter. Without an upstream filter, the quantity of dust passing through the coil was approximately 60 times the value for a MERV14 filter.

Li Yang; James E. Braun; Eckhard A. Groll

2004-06-30T23:59:59.000Z

75

Multifunctional robot to maintain boiler water-cooling tubes  

Science Conference Proceedings (OSTI)

A robot has been developed to maintain boiler water-cooling tubes. This robot has a double tracked moving mechanism, an ash cleaning device, a slag purging device, a tubes' thickness measurement device, a marking device, and a control system. This robot ... Keywords: Boiler maintenance, Boiler water-cooling tube, Climbing robot, Mobile robot

Xueshan Gao; Dianguo Xu; Yan Wang; Huanhuan Pan; Weimin Shen

2009-10-01T23:59:59.000Z

76

Identifying Transformer Incipient Events for Maintaining Distribution System Reliability  

E-Print Network (OSTI)

Identifying Transformer Incipient Events for Maintaining Distribution System Reliability Karen L events in single-phase distribution transformers. This analysis will aid in the development of an automatic detection method for internal incipient faults in the transformers. The detection method can

77

Soup to nuts: affordable tools for building and maintaining labs  

Science Conference Proceedings (OSTI)

Limited IT funds are a fact of life at most institutions. You may be surprised by how much you can do with what you have though. Using new products in conjunction with tried and true existing technologies you can take steps to maintain both your bottom ... Keywords: classroom technology, computer classrooms, computer labs, deployment, imaging, management, printing, security

Jason Wagner

2004-10-01T23:59:59.000Z

78

Establishing and maintaining long-term human-computer relationships  

Science Conference Proceedings (OSTI)

This research investigates the meaning of human-computer relationship and presents techniques for constructing, maintaining, and evaluating such relationships, based on research in social psychology, sociolinguistics, communication and ... Keywords: Human-computer interaction, embodied conversational agent, relational agent, social interface

Timothy W. Bickmore; Rosalind W. Picard

2005-06-01T23:59:59.000Z

79

A Weighted Freshness Metric for Maintaining Search Engine Local Repository  

Science Conference Proceedings (OSTI)

Current search engines maintain a local repository to improve the search efficiency. A crawler is used to periodically poll the remote web pages to update the contents of the local repository. Due to the resource limitations, some local pages may be ...

Jianchao Han; Nick Cercone; Xiaohua Hu

2004-09-01T23:59:59.000Z

80

Analysis, design, and experiments of a high-power-factor electronic ballast  

SciTech Connect

A charge pump power-factor-correction (CPPFC) converter is first derived, and its unity power factor condition is then reviewed. A single-stage power-factor-correction electronic ballast using the charge pump concept is analyzed. The design criteria are derived to optimize the electronic ballast based on the steady-state analysis. Constant lamp power operations associated with its control are also discussed. Large signal simulation and experimental results verify the theoretical analysis. It is shown that the designed electronic ballast has 0.995 power factor and 5% total harmonic distortion (THD) with lamp power variation within {+-}15% when the line input voltage changes {+-}10%.

Qian, J.; Lee, F.C. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States); Yamauchi, T. [Matsushita Electric Works, Inc., Woburn, MA (United States)

1998-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

EPRI NMAC Maintainability Review of the International Gas-Turbine Modular Helium Reactor Power Conversion Unit  

Science Conference Proceedings (OSTI)

This report provides information of interest to the designers of modular helium-reactor-driven gas turbines and persons considering the purchase of this type of plant.

2001-02-01T23:59:59.000Z

82

Compact, maintainable 80-KeV neutral beam module  

DOE Patents (OSTI)

A compact, maintainable 80-keV arc chamber, extractor module for a neutral beam system immersed in a vacuum of <10.sup.-2 Torr, incorporating a nested 60-keV gradient shield located midway between the high voltage ion source and surrounding grounded frame. The shield reduces breakdown or arcing path length without increasing the voltage gradient, tends to keep electric fields normal to conducting surfaces rather than skewed and reduces the peak electric field around irregularities on the 80-keV electrodes. The arc chamber or ion source is mounted separately from the extractor or ion accelerator to reduce misalignment of the accelerator and to permit separate maintenance to be performed on these systems. The separate mounting of the ion source provides for maintaining same without removing the ion accelerator.

Fink, Joel H. (Livermore, CA); Molvik, Arthur W. (Livermore, CA)

1980-01-01T23:59:59.000Z

83

Assessing the maintainability benefits of design restructuring using dependency analysis  

E-Print Network (OSTI)

Software developers and project managers often have to assess the quality of software design. A commonly adopted hypothesis is that a good design should cost less to maintain than a poor design. In this paper, we propose a model for quantifying the quality of a design from a maintainability perspective. Based on this model, we propose a novel strategy for predicting the Return on Investment (ROI) for possible design restructurings using procedure-level dependency analysis. We demonstrate this approach with two exploratory Java case studies. Our results show that common low-level source code transformations change the system dependency structure in a beneficial way, allowing recovery of the initial refactoring investment over a number of maintenance activities. 1.

Robert Leitch; Eleni Stroulia

2003-01-01T23:59:59.000Z

84

Maintaining Lube Oil System Cleanliness in Motor Bearing Applications  

Science Conference Proceedings (OSTI)

Lube oil analysis plays a significant role in assessing contamination levels and managing the condition of the lubricant and machine components. By establishing target levels for lubricant properties, contamination, and machine wear -- and measuring actual equipment performance against these limits -- utilities can quickly identify and resolve abnormal conditions before internal component damage occurs. This report outlines proactive techniques for maintaining lube oil system cleanliness and reducing int...

2001-11-16T23:59:59.000Z

85

An improved charge pump power factor correction electronic ballast  

SciTech Connect

An improved charge pump power factor correction (CPPFC) electronic ballast using the charge pump concept is proposed in this paper. Circuit derivation, principle of operation, and the conditions for achieving unity power factor are discussed. The proposed electronic ballast is implemented and tested with two 40-W fluorescent lamps. It is shown that 84% of overall efficiency and 1.6 of crest factor can be achieved with 200-V line input voltage. The measured line input current harmonics satisfy IEC 1000-3-2 Class C requirements. The lamp power variation range is automatically limited within {+-}15% for {+-}10% line input voltage variation without feedback control.

Qian, J.; Lee, F.C.; Yamauchi, T.

1999-11-01T23:59:59.000Z

86

Oscillatory nonhmic current drive for maintaining a plasma current  

DOE Patents (OSTI)

Apparatus and method of the invention maintain a plasma current with an oscillatory nonohmic current drive. Each cycle of operation has a generation period in which current driving energy is applied to the plasma, and a relaxation period in which current driving energy is removed. Plasma parameters, such as plasma temperature or plasma average ionic charge state, are modified during the generation period so as to oscillate plasma resistivity in synchronism with the application of current driving energy. The invention improves overall current drive efficiencies.

Fisch, Nathaniel J. (Princeton, NJ)

1986-01-01T23:59:59.000Z

87

Reliability, Availability and Maintainability Considerations for Gas Turbine Cogeneration Systems  

E-Print Network (OSTI)

The success of a cogeneration system depends upon the system being available, i.e. operating and meeting its demands under expected environmental conditions. A high availability in turn, depends on both Reliability (indicating how often the system fails), and Maintainability (indicating how fast it can be returned to a satisfactory operating state). A low availability will adversely effect important economic criteria for the project such as Discounted Cash Flow and Payback. This paper provides a structure by which these important parameters can be addressed at the design evaluation stage. The paper discusses reliability methods and practical aspects such as installation and operation considerations, including air filtration, fuel conditioning and compressor washing.

Meher-Homji, C. B.; Focke, A. B.

1984-01-01T23:59:59.000Z

88

Oscillatory nonohomic current drive for maintaining a plasma current  

DOE Patents (OSTI)

Apparatus and methods are described for maintaining a plasma current with an oscillatory nonohmic current drive. Each cycle of operation has a generation period in which current driving energy is applied to the plasma, and a relaxation period in which current driving energy is removed. Plasma parameters, such as plasma temperature or plasma average ionic charge state, are modified during the generation period so as to oscillate plasma resistivity in synchronism with the application of current driving energy. The invention improves overall current drive efficiencies.

Fisch, N.J.

1984-01-01T23:59:59.000Z

89

Notices ROUTINE USES OF RECORDS MAINTAINED IN THE SYSTEM, INCLUDING  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

83 Federal Register 83 Federal Register / Vol. 78, No. 51 / Friday, March 15, 2013 / Notices ROUTINE USES OF RECORDS MAINTAINED IN THE SYSTEM, INCLUDING CATEGORIES OF USERS AND THE PURPOSES OF SUCH USES: The Department may disclose information contained in a record in this system of records under the routine uses listed in this system of records without the consent of the individual if the disclosure is compatible with the purposes for which the record was collected. These disclosures may be made on a case-by-case basis or, if the Department has complied with the computer matching requirements of the Privacy Act of 1974, as amended (Privacy Act), under a computer matching agreement. Any disclosure of individually identifiable information from a record in this system must also comply with the requirements of section

90

Remote Sensing and Control for Establishing and Maintaining Digital Irrigation  

E-Print Network (OSTI)

The remotely sensed data from an unknown location is transmitted in real time through internet and gathered in a PC. The data is collected for a considerable period of time and analyzed in PC as to assess the suitability and fertility of the land for establishing an electronic plantation in that area. The analysis also helps deciding the plantation of appropriate plants in the location identified. The system performing this task with appropriate transducers installed in remote area, the methodologies involved in transmission and data gathering are reported.. The second part of the project deals with data gathering from remote site and issuing control signals to remote appliances in the site; all performed through internet. Therefore, this control scheme is a duplex system monitoring the irrigation activities by collecting data in one direction and issuing commands on the opposite direction. This scheme maintains the digital irrigation systems effectively and efficiently as to utilize the resources optimally f...

cellatoglu, Akin

2012-01-01T23:59:59.000Z

91

Maintaining the Lead Researchers at Oak Ridge National  

E-Print Network (OSTI)

, given annually by R&D magazine to the year's most technologically significant new products. ORNL led all all-time winner among DOE labs with 134. ORNL researchers (in bold) were recognized for the following set three world records for superconducting in 2006. As replacements for copper power cables, ORNL

92

Solar Power Fact Book  

Science Conference Proceedings (OSTI)

In conjunction with research, testing, and demonstration activities at the Solar Technology Acceleration Center (SolarTAC), the Electric Power Research Institute (EPRI) maintains a database of commonly requested technical information on photovoltaic (PV) and concentrating solar thermal power (CSP) technologies. The database addresses cost and performance, resource assessment, project siting and development, environmental impacts, policy and market drivers, and other relevant issues. The data and informat...

2010-12-23T23:59:59.000Z

93

Drilling, Completing, and Maintaining Geothermal Wells in Baca, New Mexico  

DOE Green Energy (OSTI)

A 55-MWe power plant is planned for development in the Baca location in the Jemez Mountains of New Mexico. Union Geothermal has contracted to provide the steam for the power plant. This paper uses Baca Well No. 13 as a case history to describe the drilling methods, casing program, cementing program, and completion methods used by Union. The discussion includes aerated-water drilling and the methods of solving corrosion problems in aerated water. lost circulation control in mud drilling and its effect on the subsequent casing cementing program are discussed. The paper also includes a case history of scale removal methods used in Baca Well No. 11, including drilling the scale out with a turbo-drill and attempts at chemical inhibition.

Pye, S.

1981-01-01T23:59:59.000Z

94

STATEMENT OF CONSIDERATIONS REQUEST BY SIEMENS WESTINGHOUSE POWER...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of improved reliability availability and maintainability (RAM) of existing and advanced gas turbine power plants by continuously monitoring the health of critical thermal barrier...

95

NREL: Water Power Research - Device and Component Testing  

NLE Websites -- All DOE Office Websites (Extended Search)

Testing NREL houses the nation's premier laboratory facilities for testing offshore wind and water power devices and maintains a staff of offshore-trained test engineers and...

96

PP-10 Bonneville Power Administrator | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

to construct, operate, and maintain electric transmission facilities at the U.S-Canada border. PP-10 Bonneville Power Administrator More Documents & Publications...

97

PP-03 Federal Power Commission | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Commission to construct, operate, and maintain electric transmission facilities at te U.S-Mexico border. PP-03 Federal Power Commission More Documents & Publications PP-35 Trico...

98

PP-13 Federal Power Commission | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Commission to construct, operate, and maintain electric transmission facilities at the U.S-Canadian border. PP-13 Federal Power Commission More Documents & Publications PP-231...

99

PP-45-2 Northern States Power Company  

Energy.gov (U.S. Department of Energy (DOE))

Presidential Permit authorizing Northern States Power Company to construct, operate, and maintain elextric transmission facilities at the U.S. - Canada Border.

100

Electric Power Acronyms and Definitions - Sierra Nevada Region  

NLE Websites -- All DOE Office Websites (Extended Search)

of the ISO transmission grid. Responsible for providing non-discriminatory access to the power grid, managing congestion, maintaining grid reliability and security, and providing...

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Particle Swarm Optimization Based Reactive Power Optimization  

E-Print Network (OSTI)

Reactive power plays an important role in supporting the real power transfer by maintaining voltage stability and system reliability. It is a critical element for a transmission operator to ensure the reliability of an electric system while minimizing the cost associated with it. The traditional objectives of reactive power dispatch are focused on the technical side of reactive support such as minimization of transmission losses. Reactive power cost compensation to a generator is based on the incurred cost of its reactive power contribution less the cost of its obligation to support the active power delivery. In this paper an efficient Particle Swarm Optimization (PSO) based reactive power optimization approach is presented. The optimal reactive power dispatch problem is a nonlinear optimization problem with several constraints. The objective of the proposed PSO is to minimize the total support cost from generators and reactive compensators. It is achieved by maintaining the whole system power loss as minimum...

Sujin, P R; Linda, M Mary

2010-01-01T23:59:59.000Z

102

Green Power Network: About the Green Power Network  

NLE Websites -- All DOE Office Websites (Extended Search)

About the GPN About the GPN Search Search Help More Search Options Search Site Map News TVA Seeks 126 MW of Renewables in 2014 December 2013 More News More News Subscribe to E-Mail Update Subscribe to e-mail update Events EPA Webinar - The Power of Aggregated Purchasing: How to Green Your Electricity Supply & Save Money January 15, 2014 1:00-2:00 p.m. ET Previous Webinars More News Features Green Power Market Status Report (2011 Data) Featured Green Power Reports Welcome! The Green Power Network (GPN) provides news and information on green power markets and related activities. The site provides up-to-date information on green power providers, product offerings, consumer protection issues, and policies affecting green power markets. It also includes a reference library of relevant papers, articles and reports. The Green Power Network is operated and maintained by the National Renewable Energy Laboratory for the U.S. Department of Energy.

103

Bi-directional power control system for voltage converter  

DOE Patents (OSTI)

A control system for a voltage converter includes: a power comparator for comparing a power signal on input terminals of the converter with a commanded power signal and producing a power comparison signal; a power regulator for transforming the power comparison signal to a commanded current signal; a current comparator for comparing the commanded current signal with a measured current signal on output terminals of the converter and producing a current comparison signal; a current regulator for transforming the current comparison signal to a pulse width modulator (PWM) duty cycle command signal; and a PWM for using the PWM duty cycle command signal to control electrical switches of the converter. The control system may further include: a command multiplier for converting a voltage signal across the output terminals of the converter to a gain signal having a value between zero (0) and unity (1), and a power multiplier for multiplying the commanded power signal by the gain signal to provide a limited commanded power signal, wherein power comparator compares the limited commanded power signal with the power signal on the input terminals.

Garrigan, Neil Richard (Niskayuna, NY); King, Robert Dean (Schenectady, NY); Schwartz, James Edward (Slingerlands, NY)

1999-01-01T23:59:59.000Z

104

Bi-directional power control system for voltage converter  

DOE Patents (OSTI)

A control system for a voltage converter includes: a power comparator for comparing a power signal on input terminals of the converter with a commanded power signal and producing a power comparison signal; a power regulator for transforming the power comparison signal to a commanded current signal; a current comparator for comparing the commanded current signal with a measured current signal on output terminals of the converter and producing a current comparison signal; a current regulator for transforming the current comparison signal to a pulse width modulator (PWM) duty cycle command signal; and a PWM for using the PWM duty cycle command signal to control electrical switches of the converter. The control system may further include: a command multiplier for converting a voltage signal across the output terminals of the converter to a gain signal having a value between zero (0) and unity (1), and a power multiplier for multiplying the commanded power signal by the gain signal to provide a limited commanded power signal, wherein power comparator compares the limited commanded power signal with the power signal on the input terminals. 10 figs.

Garrigan, N.R.; King, R.D.; Schwartz, J.E.

1999-05-11T23:59:59.000Z

105

Stochastic Optimal Power Flow for Reserve Determination  

Science Conference Proceedings (OSTI)

With significant levels of renewable generation to be integrated in the future electric power systems, new balancing techniques and better forecasting are needed for system operators to maintain power system security. The impact of uncertainty and variability associated with renewable generation motivates the introduction of stochastic methods when determining reserve requirements. These methods enable operators to make better use of system flexibility in order to maintain system reliability and ...

2012-12-31T23:59:59.000Z

106

Power Purchase Agreements  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Purchase Agreements Power Purchase Agreements Chandra Shah, NREL 303-384-7557 chandra.shah@nrel.gov February 2011 revised 2 | Federal Energy Management Program eere.energy.gov Overview * Customer-sited power purchase agreement (PPA) definition * Project process * Project examples * Utility Renewable Energy Services Contract (URESC) * Enhanced use lease (EUL) * PPA support, resources and key points 3 | Federal Energy Management Program eere.energy.gov * Private entity purchases, installs, owns, operates and maintains customer-sited renewable equipment * Site purchases electricity through power purchase agreement (PPA) * Pros - Renewable developer (or partner) eligible for tax incentives, accelerated depreciation - No agency up-front capital required - Renewable developer provides O&M - Minimal risk to government

107

Optimizing Power Using Transformations  

E-Print Network (OSTI)

: The increasing demand for portable computing has elevated power consumption to be one of the most critical design parameters. A high-level synthesis system, HYPER-LP, is presented for minimizing power consumption in application specific datapath intensive CMOS circuits using a variety of architectural and computational transformations. The synthesis environment consists of high-level estimation of power consumption, a library of transformation primitives, and heuristic/probabilistic optimization search mechanisms for fast and efficient scanning of the design space. Examples with varying degree of computational complexity and structures are optimized and synthesized using the HYPER-LP system. The results indicate that more than an order of magnitude reduction in power can be achieved over current-day design methodologies while maintaining the system throughput; in some cases this can be accomplished while preserving or reducing the implementation area. 1.0 Introduction VLSI research a...

Anantha P. Chandrakasan; Miodrag Potkonjak; Renu Mehra; Jan Rabaey; Robert W. Brodersen

1995-01-01T23:59:59.000Z

108

Power Operations  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Operations Outage Coordination Standards of Conduct Transmission Planning You are here: SN Home page > Power Operations Power Operations Western's Sierra Nevada Region...

109

O&M First! Maintaining Effective and Efficient Lighting Can Help...  

NLE Websites -- All DOE Office Websites (Extended Search)

Fact Sheet Maintaining Effective and Efficient Lighting Can Help Save Energy and Reduce Costs Over 20 percent of the nation's electricity is consumed by various lighting products...

110

Integration Defended: Berkeley Unifieds Strategy to Maintain School Diversity  

E-Print Network (OSTI)

to Maintain School Diversity Lisa Chavez Erica Frankenberg RSchools that Use Student Diversity to Enhance Learning ofthe Promise of Racial Diversity in American Schools, eds.

Chavez, Lisa; Frankenberg, Erica

2009-01-01T23:59:59.000Z

111

Multi-agent approach to power distribution network modelling  

Science Conference Proceedings (OSTI)

Power supply reliability has become a question of ever growing importance. Due to its geographical distribution and the high costs of maintaining electric power systems (EPS), the necessary quality cannot be achieved simply by redundancy. It is necessary ... Keywords: economic aspects of power outages, multi-agent systems, power network simulation

Miroslav Prmek; Ale Hork

2010-12-01T23:59:59.000Z

112

Observe-mine-adopt (OMA): an agile way to enhance software maintainability  

Science Conference Proceedings (OSTI)

We introduce the observe-mine-adopt (OMA) paradigm that assists organizations in making improvements to their software development processes without committing to and undertaking large-scale sweeping organizational process improvement. Specifically, ... Keywords: agile methods, experimental study, maintainability measurement, process improvement, software maintainability, software maintenance

Jane Huffman Hayes; Naresh Mohamed; Tina Hong Gao

2003-09-01T23:59:59.000Z

113

What Steps Do You Take to Maintain Your Furnace? | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Steps Do You Take to Maintain Your Furnace? Steps Do You Take to Maintain Your Furnace? What Steps Do You Take to Maintain Your Furnace? January 7, 2010 - 7:30am Addthis This week, Chris told you about his plans to maintain his furnace to keep it running efficiently. Proper maintenance is key to ensuring your heating and cooling systems are in working order. No one wants to wake up on the coldest day of the year to find that they have no heat! What steps do you take to maintain your furnace? Each Thursday, you have the chance to share your thoughts on a question about energy efficiency or renewable energy for consumers. E-mail your responses to the Energy Saver team at consumer.webmaster@nrel.gov. Addthis Related Articles Brrrrr. It's Cold In There! Saving Energy and Money Starts at Home 31,000 Homes Weatherized in June

114

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

Skip Navigation Links Skip Navigation Links DOE Order No. RA 6120.2 Repayment Process Under Department of Energy Order No. RA 6120.2, Southwestern conducts power repayment studies each year to determine the amount of revenue required to recover costs assigned to power, including the annual cost of marketing power, the cost of operating and maintaining the generating facilities, and, for the Integrated System and Sam Rayburn, the cost of the original investment in building the facilities, plus interest. Southwestern conducts three such studies, one for the Integrated System, one for Sam Rayburn Dam, and one for Robert D. Willis Dam. Upon completion of the studies, Southwestern conducts a formal public participation process, including solicitation of public comments on any proposed revenue

115

Power Purchase Agreements  

NLE Websites -- All DOE Office Websites (Extended Search)

Text Text eere.energy.gov Power Purchase Agreements Chandra Shah, NREL 303-384-7557 chandra.shah@nrel.gov February 2011 revised 2 | Federal Energy Management Program eere.energy.gov Overview * Customer-sited power purchase agreement (PPA) definition * Project process * Project examples * Utility Renewable Energy Services Contract (URESC) * Enhanced use lease (EUL) * PPA support, resources and key points 3 | Federal Energy Management Program eere.energy.gov * Private entity purchases, installs, owns, operates and maintains customer-sited renewable equipment * Site purchases electricity through power purchase agreement (PPA) * Pros - Renewable developer (or partner) eligible for tax incentives, accelerated depreciation - No agency up-front capital required - Renewable developer provides O&M

116

FOR ELECTRIC POWER TRANSMISSION  

E-Print Network (OSTI)

A contract network extends the concept of a contract path to address the problem of loop flow and congestion in electric power transmission systems. A contract network option provides a well defined, internally consistent framework for assigning long-term capacity rights to a complicated electric transmission network. The contract network respects the special conditions induced by Kirchoff's Laws; accommodates thermal, voltage and contingency constraints on transmission capacity; and can be adopted without disturbing existing methods for achieving an economic power dispatch subject to these constraints. By design, a contract network would maintain short-run efficiency through optimal spot price determination of transmission prices. Through payment of congestion rentals, the contract network makes a long-term capacityright holder indifferent between delivery of the power or receipt of payments in a settlement system. And the contract network framework can support allocation of transmission capacity rights through a competitive bidding process. CONTRACT NETWORKS

William W. Hogan; William W. Hogan

1990-01-01T23:59:59.000Z

117

Quantification of Hungry Horse Reservoir Water Levels Needed to Maintain or Enhance Reservoir Fisheries, 1985 Annual Report.  

Science Conference Proceedings (OSTI)

The Pacific Northwest Electric Power Planning and Conservation Act, passed in 1980 by Congress, has provided a mechanism which integrates and provides for stable energy planning in the Pacific Northwest. The Act created the Northwest Power Planning Council and charged the Council with developing a comprehensive fish and wildlife program to protect and enhance fish and wildlife impacted by hydroelectric development in the Columbia River Basin. Bonneville Power Administration (BPA) is one of the many agencies implementing the Council's program. The Hungry Horse Reservoir (HHR) study is part of the Council's program. This study proposes to quantify seasonal water levels needed to maintain or enhance principal gamefish species in Hungry Horse Reservoir. The specific study objectives are: (1) Quantify the amount of reservoir habitat available at different water level elevations; (2) Estimate recruitment of westslope cutthroat trout juveniles from important spawning and nursery areas; (3) Determine the abundance, growth, distribution and use of available habitat by major game species in the reservoir; (4) Determine the abundance and availability of fish food organisms in the reservoir; (5) Quantify the seasonal use of available food items by major fish species; (6) Develop relationships between reservoir drawdown and reservoir habitat use by fish and fish food organisms; and (7) Estimate the impact of reservoir operation on major gamefish species.

May, Bruce

1986-06-01T23:59:59.000Z

118

Power Plant Dams (Kansas) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Plant Dams (Kansas) Power Plant Dams (Kansas) Power Plant Dams (Kansas) < Back Eligibility Commercial Investor-Owned Utility Local Government Municipal/Public Utility Rural Electric Cooperative Utility Savings Category Water Buying & Making Electricity Program Info State Kansas Program Type Environmental Regulations Provider Health and Environment This act states the provisions for erection and maintenance of dams. When any person, corporation or city may be desirous of erecting and maintaining a milldam or dam for generating power across any watercourse, the party so desiring to do the same may run the stream over the land of any other person by ditching or otherwise, and he, she or it may obtain the right to erect and maintain said dam and keep up and maintain the necessary ditches

119

Quantification of Libby Reservoir Water Levels Needed to Maintain or Enhance Reservoir Fisheries, 1988-1996 Methods and Data Summary.  

DOE Green Energy (OSTI)

The Libby Reservoir study is part of the Northwest Power Planning Council's resident fish and wildlife program. The program was mandated by the Northwest Planning Act of 1980, and is responsible for mitigating for damages to fish and wildlife caused by hydroelectric development in the Columbia River Basin. The objective of Phase I of the project (1983 through 1987) was to maintain or enhance the Libby Reservoir fishery by quantifying seasonal water levels and developing ecologically sound operational guidelines. The objective of Phase II of the project (1988 through 1996) was to determine the biological effects of reservoir operations combined with biotic changes associated with an aging reservoir. This report summarizes the data collected from Libby Reservoir during 1988 through 1996.

Dalbey, Steven Ray

1998-03-01T23:59:59.000Z

120

Top U.S. Energy Leaders to Discuss How to Maintain Our Lead in Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Top U.S. Energy Leaders to Discuss How to Maintain Our Lead in Top U.S. Energy Leaders to Discuss How to Maintain Our Lead in Energy Innovation Top U.S. Energy Leaders to Discuss How to Maintain Our Lead in Energy Innovation September 18, 2013 - 3:45pm Addthis NEWS MEDIA CONTACT (202) 586-4940 WASHINGTON - The United States has been jockeying for leadership in the global clean energy race, with our greatest strengths derived from American innovation and entrepreneurship. This briefing will explore ways the United States can maintain a competitive lead in advanced energy technologies and enhance our economic, energy independence, and national security interests. Speakers will present examples of how strategic partnerships between the Federal government and private sector are spurring the development of the next generation of energy technologies and advanced manufacturing. Deputy

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Risk Assessment Form (This is an active document and must be maintained)  

E-Print Network (OSTI)

Risk Assessment Form (This is an active document and must be maintained) Materials Science and section will then be removed, the cutting blade demounted and the cutting bowl cleaned. SECTION 1

Cambridge, University of

122

Improved File Synchronization Techniques for Maintaining Large Replicated Collections over Slow Networks  

Science Conference Proceedings (OSTI)

We study the problem of maintaining large replicated collectionsof files or documents in a distributed environment withlimited bandwidth. This problem arises in a number of importantapplications, such as synchronization of data betweenaccounts or devices, ...

Torsten Suel; Patrick Noel; Dimitre Trendafilov

2004-03-01T23:59:59.000Z

123

Policy Flash 2013-40 Acquisition Guide Chapter 43.3 - Maintaining  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 Acquisition Guide Chapter 43.3 - Maintaining 0 Acquisition Guide Chapter 43.3 - Maintaining Alignment of Project Management with Contract Management of Non-Management and Operating (M&O) Cost Reimburstment Contracts Policy Flash 2013-40 Acquisition Guide Chapter 43.3 - Maintaining Alignment of Project Management with Contract Management of Non-Management and Operating (M&O) Cost Reimburstment Contracts Attached is Policy Flash 2013-40 Acquisition Guide Chapter 43.3 - Maintaining Alignment of Project Management with Contract Management of Non-Management and Operating (M&O) Cost Reimbursement Contracts for Capital Asset Projects, Environmental Remediation, Decontamination and Decommissioning, Facility Operations, and Other Major Projects Questions concerning this policy flash should be directed to Barbara Binney

124

Power management and power control in wireless networks  

E-Print Network (OSTI)

With the proliferation of portable computing platforms and small wireless devices, wireless networks have received more and more attention as a means for providing data communications among devices regardless of their physical locations. However, due to the slow advancement in battery technology, battery power continues to be a constrained resource in wireless networks and thus energy conservation remains to be an important issue. In this book chapter, we provide a taxonomy of power management and power control algorithms and protocols for wireless networks. We start with a description of energy consumption characteristics of wireless devices, and identify the power consumed in the wireless transmitters essentially consists of two parts: power consumed by the radio electronic and power consumed in the RF output. To save power, one can either turn off the radio electronic and put wireless devices into the power saving mode at appropriate times, or adjust the RF output power (and hence the wireless transmission range) subject to maintaining network connectivity and bi-directionality. The former techniques are termed as power management, while the latter power

Rong Zheng; Jennifer C. Hou; Ning Li

2004-01-01T23:59:59.000Z

125

Application for presidential permit OE Docket No. PP-362 Champlain Hudson Power Express Inc  

Energy.gov (U.S. Department of Energy (DOE))

Application from Champlain Hudson Power Express Incto construct, operate, and maintain electric transmission facilities at the U.S. - Canada Border.

126

Analysis and Comparison of Low Voltage Ride Through Capability of Wind Power Generators.  

E-Print Network (OSTI)

??When the wind power accounted for a total generating capacity reaches a certain percentage, wind turbine's ability to maintain operation during a fault will affect (more)

Wu, Tung-Sheng

2013-01-01T23:59:59.000Z

127

Development of a tool for simulating performance of sub systems of a combined cycle power plant; .  

E-Print Network (OSTI)

?? Abstract In Sri Lanka, around 50% of the electrical energy generation is done using thermal energy, and hence maintaining generation efficiencies of thermal power (more)

Jayasinghe, Prabodha

2012-01-01T23:59:59.000Z

128

Savings Potential of ENERGY STAR(R) External Power Adapters and Battery Chargers  

E-Print Network (OSTI)

maintaining the battery Standby Used in sensing circuitsthe AC power source in standby mode. This test was meant tothe battery and during standby would only address 25 percent

Webber, Carrie; Korn, David; Sanchez, Marla

2007-01-01T23:59:59.000Z

129

Unity, Justice and Protection: The Colored Trainmen of America's Struggle to End Jim Crow in the American Railroad Industry [and Elsewhere  

E-Print Network (OSTI)

The Colored Trainmen of America (CTA) actively challenged Jim Crow policies on the job and in the public sphere between the 1930s and 1950s. In response to lingering questions concerning the relationship between early black labor activism and civil rights protest, this study goes beyond both local lure and cursory research. This study examines the Colored Trainmen's major contributions to the advancement of African Americans. It also provides context for some of the organization's shortcomings in both realms. On the job the African American railroad workers belonging to the CTA fought valiantly to receive the same opportunities for professional growth and development as whites working in the operating trades of the railroad industry. In the public sphere, these men collectively protested second-class services and accommodations both on and off the clock. Neither their agenda, the scope of their activities, nor their influence was limited to the railroad lines the members of the CTA operated within the Gulf Coast region. The CTA belonged to a progressive coalition comprised of four other powerful independent African American labor unions committed to unyielding labor activism and the toppling of Jim Crow. Together, they all worked to effectuate meaningful social change in partnership with national civil rights attorney Charles H. Houston. Houston's experience and direction, coupled with the CTA's dedicated membership and willingness to challenge authority, created considerable momentum in movements aimed at toppling racial inequality in the workplace and elsewhere. Like most of their predecessors, the CTA's struggle for advancement fits within a continuum of successive challenges to economic exploitation and racial inequality. No single person or organization can take full credit for ending segregation or achieving equality. Many who remain nameless and faceless contributed and sacrificed. This study not only chronicles the contribution of a relatively unsung African American labor organization that waged war against Jim Crow on two different fronts, it also pays homage to a few more individuals who made a difference in the lives of an entire race of people during the course of a bitterly contested, never-ending struggle for racial equality in the United States of America during the twentieth century.

James, Ervin

2012-08-01T23:59:59.000Z

130

Portable battery powered system  

SciTech Connect

In a exemplary embodiment, a battery conditioning system monitors battery conditioning and includes a memory for storing data based thereon; for example, data may be stored representative of available battery capacity as measured during a deep discharge cycle. With a microprocessor monitoring battery operation of a portable unit, a measure of remaining battery capacity can be calculated and displayed. Where the microprocessor is permanently secured to the battery so as to receive operating power therefrom during storage and handling, the performance of a given battery in actual use can be accurately judged since the battery system can itself maintain a count of accumulated hours of use and other relevant parameters.

Koenck, S. E.

1985-11-12T23:59:59.000Z

131

Reactive Power Compensator.  

DOE Patents (OSTI)

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation. 26 figs.

El-Sharkawi, M.A.; Venkata, S.S.; Chen, M.; Andexler, G.; Huang, T.

1992-07-28T23:59:59.000Z

132

Reactive power compensator  

DOE Patents (OSTI)

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Woodinville, WA); Chen, Mingliang (Kirkland, WA); Andexler, George (Everett, WA); Huang, Tony (Seattle, WA)

1992-01-01T23:59:59.000Z

133

Reliability by design in distributed power transmission networks  

Science Conference Proceedings (OSTI)

The system operator of a large power transmission network must ensure that power is delivered whenever there is demand in order to maintain highly reliable electric service. To fulfill this mandate, the system operator must procure reserve capacity to ... Keywords: Inventory theory, Networks, Optimization, Power transmission

Mike Chen; In-Koo Cho; Sean P. Meyn

2006-08-01T23:59:59.000Z

134

Interactive Trouble Condition Sign Discovery for Hydroelectric Power Plants  

Science Conference Proceedings (OSTI)

Kyushu Electric Power Co.,Inc. collects different sensor data and weather information (hereafter, operation data) to maintain the safety of hydroelectric power plants while the plants are running. It is very rare to occur trouble condition in the plants. ... Keywords: Data Mining, Hydroelectric Power Plant, Support Vector Machine, Trouble Condition Detection

Takashi Onoda; Norihiko Ito; Hironobu Yamasaki

2009-07-01T23:59:59.000Z

135

Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS Tutorial_MAINTAIN_PROJECT_HISTORY.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MAINTIN PROJECT HISTORY MAINTIN PROJECT HISTORY REV: APRIL 2009 1 1. To update your project history, click on the "PMCDP Menu" and choose "Maintain project history." Maintain Project History ESS Tutorial, Project Management Career Development Program MAINTIN PROJECT HISTORY REV: APRIL 2009 2 2. A screen with the header "PMCDP Profile for [Your Name]" will appear titled "Step 3: Maintain project history." Options: Delete: This will delete all information for the selected project as currently showing in the table. Update: This will bring you back to the original input screen for project information. View Description: This will bring up a text box that will allow you to see the description previously entered. Sort: Project history information is presented in date-order, with the most recent position

136

Save Money and Stay Cool with an Efficient, Well-Maintained Air Conditioner  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Save Money and Stay Cool with an Efficient, Well-Maintained Air Save Money and Stay Cool with an Efficient, Well-Maintained Air Conditioner Save Money and Stay Cool with an Efficient, Well-Maintained Air Conditioner June 29, 2010 - 7:30am Addthis Eric Barendsen Energy Technology Program Specialist, Office of Energy Efficiency and Renewable Energy OK. It's officially summer here in Washington, D.C. I'm seeking the coolest, shadiest places possible as I get ready for the hottest few months of the year. It's already been a hot June in much of the country, and it may end up being one of the hottest Junes on record in DC. Naturally, I'm starting to think about how I'm going to stay cool this summer, while trying to minimize my energy use. Drew provided some excellent tips on summertime energy savings in his blog post two weeks ago,

137

Maintaining nuclear stability in times of transition focus of talk at  

NLE Websites -- All DOE Office Websites (Extended Search)

January » January » Bradbury Science Museum talk Maintaining nuclear stability in times of transition focus of talk at Bradbury Science Museum Houston "Terry" Hawkins talks about the role that the nation's nuclear weapons stockpile plays in maintaining the nation's defense - and that of our allies. January 9, 2014 Bradbury Science Museum Bradbury Science Museum Contact Steve Sandoval Communications Office (505) 665-9206 Email "President Obama has reaffirmed that as long as nuclear weapons exist the U.S. will maintain a safe, secure and effective arsenal that guarantees the defense of our country, our allies and partners," said Hawkins. First in series of evening lectures open to public LOS ALAMOS, N.M., Jan. 9, 2014-Los Alamos National Laboratory Senior

138

Save Money and Stay Cool with an Efficient, Well-Maintained Air Conditioner  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Save Money and Stay Cool with an Efficient, Well-Maintained Air Save Money and Stay Cool with an Efficient, Well-Maintained Air Conditioner Save Money and Stay Cool with an Efficient, Well-Maintained Air Conditioner June 29, 2010 - 7:30am Addthis Eric Barendsen Energy Technology Program Specialist, Office of Energy Efficiency and Renewable Energy OK. It's officially summer here in Washington, D.C. I'm seeking the coolest, shadiest places possible as I get ready for the hottest few months of the year. It's already been a hot June in much of the country, and it may end up being one of the hottest Junes on record in DC. Naturally, I'm starting to think about how I'm going to stay cool this summer, while trying to minimize my energy use. Drew provided some excellent tips on summertime energy savings in his blog post two weeks ago,

139

Current-source charge-pump power-factor-correction electronic ballast  

SciTech Connect

A current-source charge-pump power-factor-correction (CS-CPPFC) electronic ballast is presented in this paper. Unity-power-factor condition and principle of operation using the CP concept are derived and analyzed. Based on the steady-state analysis, the design considerations are discussed in detail. It is shown that the power switch only deals with the resonant load current, which is the same as in the two-stage approach so that small-current rating devices can be used. The developed CS-CPPFC electronic ballast can save one inductor and has a potentially low cost. The CS-CP electronic ballast with switching frequency modulation to improve crest factor is developed, implemented, and tested. It is shown that 0.99 power factor, 11.3% total harmonic distortion (THD), and 1.54 crest factor can be achieved for 85-W fluorescent lamps.

Qian, J.; Lee, F.C.Y. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States); Yamauchi, Tokushi [Matsushita Electric Works, Inc., Woburn, MA (United States)

1998-05-01T23:59:59.000Z

140

Power Electronics  

Energy.gov (U.S. Department of Energy (DOE))

Power electronics (PE) play a critical role in transforming the current electric grid into the next-generation grid. PE enable utilities to deliver power to their customers effectively while...

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Wind Power  

NLE Websites -- All DOE Office Websites (Extended Search)

Power As the accompanying map of New Mexico shows, the best wind power generation potential near WIPP is along the Delaware Mountain ridge line of the southern Guadalupe Mountains,...

142

Power Supplies  

Science Conference Proceedings (OSTI)

Figure: ...Fig. 5 Typical medium-frequency induction power supply incorporating (a) a parallel inverter and (b) a series inverter...

143

Power supply  

DOE Patents (OSTI)

A modular, low weight impedance dropping power supply with battery backup is disclosed that can be connected to a high voltage AC source and provide electrical power at a lower voltage. The design can be scaled over a wide range of input voltages and over a wide range of output voltages and delivered power.

Yakymyshyn, Christopher Paul (Seminole, FL); Hamilton, Pamela Jane (Seminole, FL); Brubaker, Michael Allen (Loveland, CO)

2007-12-04T23:59:59.000Z

144

Examining transmission power in minimum capacity underwater acoustic networks  

E-Print Network (OSTI)

This paper explores the prospect of reducing the transmission power required to operate links within an underwater acoustic network by minimizing the total capacity of the network while maintaining certain data flow ...

Stanchak, Kathryn E

2010-01-01T23:59:59.000Z

145

Liquid Waste Processing Facilities (LWPF) Reliability and Availability and Maintainability (RAM) Analysis  

SciTech Connect

A reliability, availability, and maintainability (RAM) analysis was prepared for the liquid effluents support being provided to the River Protection Project Waste Treatment Plant (WTP). The availability of liquid effluents services to the WTP was determined. Recommendations are provided on improvements and upgrades to increase the availability of the Liquid Waste Processing Facilities treatment and disposal systems.

LOWE, S.S.

2001-02-20T23:59:59.000Z

146

Thermal element for maintaining minimum lamp wall temperature in fluorescent fixtures  

DOE Patents (OSTI)

In a lighting fixture including a lamp and a housing, an improvement is disclosed for maintaining a lamp envelope area at a cooler, reduced temperature relative to the enclosed housing ambient. The improvement comprises a thermal element in thermal communication with the housing extending to and springably urging thermal communication with a predetermined area of the lamp envelope surface.

Siminovitch, Michael J. (Richmond, CA)

1992-01-01T23:59:59.000Z

147

Thermal element for maintaining minimum lamp wall temperature in fluorescent fixtures  

DOE Patents (OSTI)

In a lighting fixture including a lamp and a housing, an improvement is disclosed for maintaining a lamp envelope area at a cooler, reduced temperature relative to the enclosed housing ambient. The improvement comprises a thermal element in thermal communication with the housing extending to and springably urging thermal communication with a predetermined area of the lamp envelope surface. 12 figs.

Siminovitch, M.J.

1992-11-10T23:59:59.000Z

148

Milk fat globules are individually sur-rounded by a membrane which maintains  

E-Print Network (OSTI)

and renders them compatible with the aqueous environment [7]. Milk fat globules membranes (MFGM) compositionMilk fat globules are individually sur- rounded by a membrane which maintains their integrity, including the main specific butyrophilin, would be 1. INTRODUCTION In milk, fat is predominantly present

Recanati, Catherine

149

Guidance and Recommended Procedures for Maintaining and Using RACKLIFE Version 1.10 Models  

Science Conference Proceedings (OSTI)

RACKLIFE is a spent fuel rack management tool that can be applied to extend the useful service life of racks utilizing Boraflex as the neutron absorber material for nuclear criticality control. This document provides procedures and guidance for maintaining and using RACKLIFE models.

2002-04-23T23:59:59.000Z

150

Non-equilibrium structures: How can they be maintained? Signe Kjelstrup,  

E-Print Network (OSTI)

or by obtaining energy from the outside, of course! A non-equilibrium structure is maintained by supply of energy everywhere; in nature and in industry. Nature has evolved over billions of years, and only the fittest have in some sense. Can the understanding of natural structures be helpful for man-made designs of energy

Kjelstrup, Signe

151

Method and apparatus for maintaining the pH in zinc-bromine battery systems  

DOE Patents (OSTI)

A method and apparatus for maintaining the pH level in a zinc-bromine battery features reacting decomposition hydrogen with bromine in the presence of a catalyst. The catalyst encourages the formation of hydrogen and bromine ions. The decomposition hydrogen is therefore consumed, alloying the pH of the system to remain substantially at a given value.

Grimes, Patrick G. (Westfield, NJ)

1985-09-10T23:59:59.000Z

152

Unity, Oregon: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

118.1927121° 118.1927121° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":44.4373835,"lon":-118.1927121,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

153

The unity of the fundamental interactions  

Science Conference Proceedings (OSTI)

This book offers a collection of authoritative papers which provides the reader with a plenary survey of some of the latest developments in the field of high-energy interactions. The contributing physicists offer a comprehensive review of recent significant findings from both theoretical and experimental studies in high-energy interactions. Topics include the end of the high-energy frontier, monopoles, numerical studies of gauge field theories, expectations for the next generation of experiments, unified models, cosmology, supersymmetry, neutrino physics at Fermilab, heavy flavor production in the highest-energy (pp) interactions, b-quark physics, hadron production in e/sup +/e/sup -/ annihilation, the search for new particles and electroweak interference effects in e/sup +/e/sup -/ interactions, CP violation, and high-energy soft (pp) interactions. Includes essays by Edward Teller and P.A.M. Dirac on their lives as physicists, and one by E.P. Wigner on ''the glorious days of physics.''

Zichichi, A.

1983-01-01T23:59:59.000Z

154

Unity, Wisconsin: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

0.3165242° 0.3165242° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":44.8516322,"lon":-90.3165242,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

155

Variable pressure power cycle and control system  

DOE Patents (OSTI)

A variable pressure power cycle and control system that is adjustable to a variable heat source is disclosed. The power cycle adjusts itself to the heat source so that a minimal temperature difference is maintained between the heat source fluid and the power cycle working fluid, thereby substantially matching the thermodynamic envelope of the power cycle to the thermodynamic envelope of the heat source. Adjustments are made by sensing the inlet temperature of the heat source fluid and then setting a superheated vapor temperature and pressure to achieve a minimum temperature difference between the heat source fluid and the working fluid.

Goldsberry, Fred L. (Spring, TX)

1984-11-27T23:59:59.000Z

156

Putting Economic Power In Distributed Power t  

U.S. Energy Information Administration (EIA)

Putting Economic Power in Distributed Power. A distributed electricity generation system, often called distributed power, usually consists of ...

157

Characteristics of Electricity Storage Technologies for Maintaining Reliability of Grid with High Amounts of Intermittent Energy.  

E-Print Network (OSTI)

??For the grid to be stable, the supply of power must equal the demands of the consumer at every moment during the day. The unpredictable (more)

Sundararagavan, Sandhya

2010-01-01T23:59:59.000Z

158

Power Marketing  

NLE Websites -- All DOE Office Websites (Extended Search)

Certificate Solicitations Benefit Review Energy Services Rates and Repayment WindHydro Integration Feasibility Study Send correspondence to: Power Marketing Manager Western...

159

Computer application for design activity in power plants  

Science Conference Proceedings (OSTI)

Software for Design Activity in Power Plants' helps the Power Plant engineers and managers to manage the development and design activities of equipments in the field of power plants. This paper is basically concerned with the computerization of the design activity of Condenser, vital equipment in Heat Exchanger Unit of Thermal Power Plant required for condensing the steam and for further reclaimable purposes to achieve economy. This software will also provide facilities to maintain user profile and the respective work details.

Giri, Parimal Kumar; Srivastava, Sonam [Apeejay College of Engineering, Sohna, Gurgaon (India)

2010-10-26T23:59:59.000Z

160

Plant Engineering: Guidelines for Establishing, Maintaining, and Extending the Shelf Life Capability of Limited Life Items  

Science Conference Proceedings (OSTI)

In accordance with 10CFR50 Appendix B, 10CFR71, and 10CFR72, nuclear utilities have a commitment to establish and maintain material control programs to assure the safety and reliability of generation facilities. Economic considerations demand that shelf life for a limited life item be maximized without affecting plant safety. Once shelf life is established, a utility may need to evaluate the usefulness of an item with an expired shelf life. In addition, technical incongruities may shorten the remaining s...

2011-11-03T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Method and apparatus for maintaining equilibrium in a helical axis stellarator  

DOE Patents (OSTI)

Apparatus for maintaining three-dimensional MHD equilibrium in a plasma contained in a helical axis stellerator includes a resonant coil system, having a configuration such that current therethrough generates a magnetic field cancelling the resonant magnetic field produced by currents driven by the plasma pressure on any given flux surface resonating with the rotational transform of another flux surface in the plasma. Current through the resonant coil system is adjusted as a function of plasma beta.

Reiman, Allan (Princeton, NJ); Boozer, Allen (Rocky Hill, NJ)

1987-01-01T23:59:59.000Z

162

Method and apparatus for maintaining equilibrium in a helical axis stellarator  

DOE Patents (OSTI)

Apparatus for maintaining three-dimensional MHD equilibrium in a plasma contained in a helical axis stellarator includes a resonant coil system, having a configuration such that current therethrough generates a magnetic field cancelling the resonant magnetic field produced by currents driven by the plasma pressure on any given flux surface resonating with the rotational transform of another flux surface in the plasma. Current through the resonant coil system is adjusted as a function of plasma beta.

Reiman, A.; Boozer, A.

1984-10-31T23:59:59.000Z

163

Field tests of a novel inverter for photovoltaic power conditioning  

SciTech Connect

The Dickerson inverter synthesizes a sinewave current from a photovoltaic array that is segmented into a number of subarrays. These subarrays are switched among the ac phases so that the current from a given subarray is continuous, and each phase is connected at all times to one or more subarrays. The control scheme assures a near-unity power factor current with real-time phase adjustment to power-system disturbances. A prototype inverter was operated into a three-phase power system, with the dc supplied by a photovoltaic array at Sandia National Laboratories. The results of these tests under normal, abnormal and fault conditions are reported. Inversion efficiencies up to 99% were achieved with 0.97 power factor. A simple filter reduced current harmonics from 18% to 5%. The performance for the inverter was projected for a 480-V, three-phase system at the 50-kVA level. An analysis of filtering costs indicates that harmonic reduction to 5% can be achieved at under $0.003 per watt for typical central-station applications. The intended power range for these inverters is 50--250 kVA. The cost to produce the inverter at the 50-kVA level in quantities of 1000 units is estimated to be $0.05 per watt, which is less than the projected cost of other 50-kVA inverters. 22 figs., 9 tabs.

Dickerson, A.; Bower, W.; Schalles, F.

1989-05-01T23:59:59.000Z

164

Analysis and design of a high power factor, single-stage electronic dimming ballast  

SciTech Connect

This paper presents the analysis, design, and practical consideration of a single-stage electronic dimming ballast with unity power factor. The power stage of the ballast is derived from combining a buck-boost converter and a half-bridge series-resonant parallel-loaded inverter (SRPLI). With the plasma model of the lamp, the analysis of the ballast is carried out, from which the key equations used for dimming control are derived. Starting performance and dimming consideration are also addressed in the paper. In this dimming ballast, both pulsewidth modulation (PWM) and variable-frequency control strategies are employed. The discussed ballast with the controls can save a controller and a switch driver, reduce size and cost, and possibly increase system reliability over conventional two-stage systems in the applications with moderate power level. Simulated and experimental results of the ballast for an OSRAM T8 32-W lamp are used to verify the discussion.

Wu, T.F.; Yu, T.H. [National Chung Cheng Univ., Chia-Yi (Taiwan, Province of China)

1998-05-01T23:59:59.000Z

165

New continuous-input current charge pump power-factor-correction electronic ballast  

SciTech Connect

Continuous-input current charge pump power-factor-correction (CIC-CPPFC) electronic ballasts are proposed in this paper. The CPPFC circuit and unity power factor condition using the charge pump concept are derived and analyzed. The average lamp current control with switching frequency modulation was developed so that the low crest factor and constant lamp power operation can be achieved. The developed electronic ballast has continuous input current, so that a small line input filter can be used. The proposed CIC-CPPFC electronic ballast was implemented and tested with two 45-W fluorescent lamps. It is shown that the measured line input current harmonics satisfy IEC 1000-3-2 Class C requirements.

Qian, J.; Lee, F.C. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States); Yamauchi, Tokushi [Matsushita Electric Works, Ltd., Osaka (Japan). Lighting Research and Development Center

1999-03-01T23:59:59.000Z

166

Solar Power Fact Book: Second Edition  

Science Conference Proceedings (OSTI)

In conjunction with research, testing, and demonstration activities at the Solar Technology Acceleration Center (SolarTAC), the Electric Power Research Institute (EPRI) maintains a database of commonly requested technical information on photovoltaic (PV) and concentrating solar thermal power (CSP) technologies. The database addresses cost and performance, resource assessment, project siting and development, environmental impacts, policy and market drivers, and other relevant issues. The data and informat...

2011-12-30T23:59:59.000Z

167

Increasing Student Interest and Comprehension in Power Engineering Education at the Graduate and Undergraduate Levels  

E-Print Network (OSTI)

contains elective courses such as power system analysis, power electronics and drives, advanced electric in power engineering have entered the arena; computer applications and software development firms now hire to maintaining the sinusoidal voltage waveshape at all load buses. Increasing reliability and selling power

168

Solar Power  

NLE Websites -- All DOE Office Websites (Extended Search)

Solar Power Solar Power Project Opportunities Abound in the Region The WIPP site is receives abundant solar energy with 6-7 kWh/sq meter power production potential As the accompanying map of New Mexico shows, the WIPP site enjoys abundant year-round sunshine. With an average solar power production potential of 6-7 kWh/sq meter per day, one exciting project being studied for location at WIPP is a 30-50 MW Solar Power Tower: The American Solar Energy Society (ASES) is is a national trade association promoting solar energy as a clean source of electricity, and provides a comprehensive resource for additional information. DOE's Office of Energy Efficiency and Renewable Energy is also a comprehensive resource for more information on renewable energy.

169

Power system  

DOE Patents (OSTI)

A power system includes a prime mover, a transmission, and a fluid coupler having a selectively engageable lockup clutch. The fluid coupler may be drivingly connected between the prime mover and the transmission. Additionally, the power system may include a motor/generator drivingly connected to at least one of the prime mover and the transmission. The power-system may also include power-system controls configured to execute a control method. The control method may include selecting one of a plurality of modes of operation of the power system. Additionally, the control method may include controlling the operating state of the lockup clutch dependent upon the mode of operation selected. The control method may also include controlling the operating state of the motor/generator dependent upon the mode of operation selected.

Hickam, Christopher Dale (Glasford, IL)

2008-03-18T23:59:59.000Z

170

Solar Power for Tanzania  

SciTech Connect

Condensed list of products and activities: 8 educational posters and 1 informational brochure (all original illustrations and text); a business plan with micro-agreements; corporation created called Tanzanian Power, LLC; business feasibility study developed with the University of Albany; Hampshire College collaborated in project development; research conducted seeking similar projects in underdeveloped countries; Citibank proposal submitted (but rejected); cleaned and sent PV panels to Tanzania; community center built in Tanzania; research and list provided to Robinson for educational TV videos and product catalogs; networked with Chase Manhattan Bank for new solar panels; maintained flow of information among many people (stateside and Tanzania); wrote and sent press releases and other outreach information. Several families purchased panels.

Chen, Christine; Gerace, Jay; Mehner, Nicole; Mohamed, Sharif; Reiss, Kelly

1999-12-06T23:59:59.000Z

171

Portable battery powered system  

SciTech Connect

In an exemplary embodiment, a battery monitoring system includes sensors for monitoring battery parameters and a memory for storing data based thereon; for example, data may be stored representative of available battery capacity as measured during a deep discharge cycle, and by monitoring battery current thereafter during operation, a relatively accurate measure of remaining battery capacity becomes available. The battery monitoring system may include programmed processor circuitry and may be secured to the battery so as to receive operating power therefrom during storage and handling; thus, the performance of a given battery in actual use can be accurately judged since the battery system can itself maintain a count of accumulated hours of use and other relevant parameters.

Koenck, S.E.

1984-06-19T23:59:59.000Z

172

24 Hour Day-Ahead Reactive Power Forecasting and Optimal Scheduling  

Science Conference Proceedings (OSTI)

Reactive power management affects not only the system voltage profiles but also system efficiencies. Changes in the flow of reactive power have an influence on system losses. Reactive power forecasting and optimal scheduling of power system control elements can be conducted to efficiently and reliably transfer power across the system. The tool discussed in this report optimizes the power system to produce a security-constrained case, reduce losses, increase reactive reserve, and securely maintain ...

2013-12-29T23:59:59.000Z

173

The potential role of new technology for enhanced safety and performance of nuclear power plants through improved service maintenance  

E-Print Network (OSTI)

Refinements in the safety and performance of nuclear power plants must be made to maintain public confidence and ensure competitiveness with other power sources. The aircraft industry, US Navy, and other programs have ...

Achorn, Ted Glen

1991-01-01T23:59:59.000Z

174

Nondestructive Evaluation: Recommended Practices for Maintaining Radiation Safety of Radiographic Operations at a Nuclear Plant  

Science Conference Proceedings (OSTI)

Radiation safety programs for radiographic operations at nuclear power plants are more complex than for those operations at other types of industrial and commercial facilities. This level of complexity arises because of the numerous challenges to maintenance of excellence in radiation safety at nuclear power facilities where sources of radiation may be found at various locations in the facility and multiple safety functions must be considered at all times. The facilities themselves are also large with mu...

2010-12-23T23:59:59.000Z

175

Hanford Site Guide for Preparing and Maintaining Fenerator Group Pollution Prevention Program Documentation  

Science Conference Proceedings (OSTI)

This document provides guidance to generator groups for preparing and maintaining documentation of Pollution Prevention/Waste Minimization (P2/WMin) Program activities. The guidance is one of a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan (DOE-RL, 1998a) and Prime Contractor implementation plans describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and (300501) (RCRA and EPA, 1994). Documentation guidance for the following five P2/WMin elements are discussed: Fiscal Year (FY) Goals; Budget and Staffing; Waste Minimization (WMinn ) Assessments (WMAs); Pollution Prevention (P2) Reporting; WMin Certification.

PLACE, B.G.

1999-11-01T23:59:59.000Z

176

Power Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Projects Power Projects Contact SN Customers Environmental Review-NEPA Operations & Maintenance Planning & Projects Power Marketing Rates You are here: SN Home page > About SNR Power Projects Central Valley: In California's Central Valley, 18 dams create reservoirs that can store 13 million acre-feet of water. The project's 615 miles of canals irrigate an area 400 miles long and 45 miles wide--almost one third of California. Powerplants at the dams have an installed capacity of 2,099 megawatts and provide enough energy for 650,000 people. Transmission lines total about 865 circuit-miles. Washoe: This project in west-central Nevada and east-central California was designed to improve the regulation of runoff from the Truckee and Carson river systems and to provide supplemental irrigation water and drainage, as well as water for municipal, industrial and fishery use. The project's Stampede Powerplant has a maximum capacity of 4 MW.

177

The virtual power system testbed and inter-testbed integration  

Science Conference Proceedings (OSTI)

The Virtual Power System Testbed (VPST) at University of Illinois at Urbana-Champaign is part of the Trustworthy Cyber Infrastructure for the Power Grid (TCIP) and is maintained by members of the Information Trust Institute (ITI). VPST is designed to ...

David C. Bergman; Dong Jin; David M. Nicol; Tim Yardley

2009-08-01T23:59:59.000Z

178

A learning control of unused energy power generation  

Science Conference Proceedings (OSTI)

In recent years, the development of new clean energy without dependence on fossil fuel has become urgent. This article proposes a learning control system for power generation using a low-temperature gap which has been designed to maintain the speed of ... Keywords: BP neural network, Evaporator, Learning control, Low thermal gap, Power generator, Turbine

Satomi Shikasho; Kun-Young Han; Ji-Sun Shin; Chui Chengyou; Hee-Hyol Lee

2010-12-01T23:59:59.000Z

179

Women @ Energy: Maria Power | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Power Women @ Energy: Maria Power April 1, 2013 - 9:53am Addthis Maria Power is the Principal Engineer for Accelerator Control Systems at Argonne National Laboratory. Maria Power is the Principal Engineer for Accelerator Control Systems at Argonne National Laboratory. Check out other profiles in the Women @ Energy series and share your favorites on Pinterest. Maria Power is the Principal Engineer for Accelerator Control Systems at Argonne National Laboratory. In this role, she designs, develops, and maintains the computer control system and diagnostic tools and software for the ATLAS accelerator. Maria also travels internationally for conferences and Joint Accelerator Conferences Website team meetings. She has held this position since 2004, and is also an active member of Argonne National

180

Maintaining scale as a realiable computational system for criticality safety analysis  

SciTech Connect

Accurate and reliable computational methods are essential for nuclear criticality safety analyses. The SCALE (Standardized Computer Analyses for Licensing Evaluation) computer code system was originally developed at Oak Ridge National Laboratory (ORNL) to enable users to easily set up and perform criticality safety analyses, as well as shielding, depletion, and heat transfer analyses. Over the fifteen-year life of SCALE, the mainstay of the system has been the criticality safety analysis sequences that have featured the KENO-IV and KENO-V.A Monte Carlo codes and the XSDRNPM one-dimensional discrete-ordinates code. The criticality safety analysis sequences provide automated material and problem-dependent resonance processing for each criticality calculation. This report details configuration management which is essential because SCALE consists of more than 25 computer codes (referred to as modules) that share libraries of commonly used subroutines. Changes to a single subroutine in some cases affect almost every module in SCALE! Controlled access to program source and executables and accurate documentation of modifications are essential to maintaining SCALE as a reliable code system. The modules and subroutine libraries in SCALE are programmed by a staff of approximately ten Code Managers. The SCALE Software Coordinator maintains the SCALE system and is the only person who modifies the production source, executables, and data libraries. All modifications must be authorized by the SCALE Project Leader prior to implementation.

Bowmann, S.M.; Parks, C.V.; Martin, S.K.

1995-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Green Power Network: Green Power Marketing  

NLE Websites -- All DOE Office Websites (Extended Search)

to main content U.S. Department of Energy Energy Efficiency and Renewable Energy Green Power Network About the GPN Green Power Markets Buying Green Power Onsite Renewable...

182

Reduce power outages  

SciTech Connect

A case history shows the cost-effectiveness of doing a reliability study on a new, grassroots refinery constructed in Venezuela. Constructing grassroots refineries in developing countries pose many challenges, especially when considering electrical power and steam supplies. Without dependable electrical and steam sources, the refinery will not operate according to design expectations. Consequently, utility systems are critical and expensive challenges that must be considered early in design. Because of tighter operating budgets, refiners are equally interested in cutting out system overdesign. Redundant backup systems are damaging in capital and operating expenditures. Using reliability analysis techniques, designers can evaluate the reliability, availability and maintainability of operating systems. In the following example, a Venezuelan operating company used a reliability analysis to: assess onstream factors for the refinery`s power plant; identify critical equipment that have the greatest impact on available electrical and steam sources; and achieve a cost-effective equipment configuration that eliminates redundant backup systems. Results from the study allowed decision-makers to initiate objective plans and created an equipment-failure database that will service the refinery for its useful life.

Goyal, R. [BAPCO, Awali (Bahrain); Ramirez, R. [Corpoven S.A., Caracas (Venezuela)

1995-06-01T23:59:59.000Z

183

Power inverters  

DOE Patents (OSTI)

Power inverters include a frame and a power module. The frame has a sidewall including an opening and defining a fluid passageway. The power module is coupled to the frame over the opening and includes a substrate, die, and an encasement. The substrate includes a first side, a second side, a center, an outer periphery, and an outer edge, and the first side of the substrate comprises a first outer layer including a metal material. The die are positioned in the substrate center and are coupled to the substrate first side. The encasement is molded over the outer periphery on the substrate first side, the substrate second side, and the substrate outer edge and around the die. The encasement, coupled to the substrate, forms a seal with the metal material. The second side of the substrate is positioned to directly contact a fluid flowing through the fluid passageway.

Miller, David H. (Redondo Beach, CA); Korich, Mark D. (Chino Hills, CA); Smith, Gregory S. (Woodland Hills, CA)

2011-11-15T23:59:59.000Z

184

Section_201_Establishing_Maintaining_and_Deactivating_Limited_and_Vault-Type_Rooms  

NLE Websites -- All DOE Office Websites (Extended Search)

201 201 Establishing, Maintaining, and Deactivating Limited Areas and Vault-Type Rooms Description Classified matter must be processed, discussed, handled, or stored in designated Limited Areas (LAs) or Vault-Type Rooms (VTRs). LAs and VTRs must have security measures in place to detect and deter unauthorized persons from gaining access to the classified matter. This includes measures to prevent unauthorized persons from seeing or hearing classified information. All LAs and VTRs at Headquarters (HQ) must be approved by the Office of HQ Security Operations (HS-90) prior to the initiation of classified activities or the introduction of classified material or equipment. Definitions of a LA and VTR: 1. Limited Area (LA)--An LA is a security area designated for the protection of classified

185

EnergySmart Schools Tips: Retrofitting, Operating, and Maintaining Existing Buildings  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EnergySmart Schools EnergySmart Schools EnergySmart Schools Tips: Retrofitting, Operating, and Maintaining Existing Buildings Quick wins and long-term facility management strategies that pay for themselves and result in energy savings Typical School Energy Use Distribution (varies by climate zone) 30% Lighting Cooling Space Heating Water Heating Other 23% 30% 10% 7% Combining preventative operations and maintenance (O&M) with strategic retrofitting of building systems improves a school's energy performance. For schools with limited resources and experience, "quick wins" in O&M and retrofitting provide a valuable starting point to energy management. As a next step, strategically prioritizing long- and short-term measures produces overall returns on investment. Please refer to the

186

Apparatus for maintaining aligment of a shrinking weld joint in an electron-beam welding operation  

DOE Patents (OSTI)

The invention is directed to an apparatus for automatically maintaining a shrinking weld joint in alignement with an electron beam during an electron-beam multipass-welding operation. The apparatus utilizes a bias means for continually urging a workpiece-supporting face plate away from a carriage mounted base that rotatably supports the face plate. The extent of displacement of the face plate away from the base in indicative of the shrinkage occuring in the weld joint area. This displacement is measured and is used to move the base on the carriage a distance equal to one-half the displacement for aligning the weld joint with the electron beam during each welding pass.

Trent, J.B.; Murphy, J.L.

1980-01-03T23:59:59.000Z

187

Apparatus for maintaining alignment of a shrinking weld joint in an electron-beam welding operation  

SciTech Connect

The present invention is directed to an apparatus for automatically maintaining a shrinking weld joint in alignment with an electron beam during an electron-beam multipass-welding operation. The apparatus utilizes a biasing device for continually urging a workpiece-supporting face plate away from a carriage mounted base that rotatably supports the face plate. The extent of displacement of the face plate away from the base is indicative of the shrinkage occuring in the weld joint area. This displacement is measured and is used to move the base on the carriage a distance equal to one-half the displacement for aligning the weld joint with the electron beam during each welding pass.

Trent, Jett B. (Knoxville, TN); Murphy, Jimmy L. (Oak Ridge, TN)

1981-01-01T23:59:59.000Z

188

An improved algorithm for maintaining arc consistency in dynamic constraint satisfaction problems  

E-Print Network (OSTI)

Real world is dynamic in its nature, so techniques attempting to model the real world should take this dynamicity in consideration. A well known Constraint Satisfaction Problem (CSP) can be extended this way to a so called Dynamic Constraint Satisfaction Problem (DynCSP) that supports adding and removing constraints in runtime. As Arc Consistency is one of the major techniques in solving CSPs, its dynamic version is of a particular interest for DynCSPs. This paper presents an improved version of AC|DC-2 algorithm for maintaining maximal arc consistency after constraint retraction. This improvement leads to runtimes better than the so far fastest dynamic arc consistency algorithm DnAC-6 while keeping low memory consumption. Moreover, the proposed algorithm is open in the sense of using either non-optimal AC-3 algorithm keeping a minimal memory consumption or optimal AC-3.1 algorithm improving runtime for constraint addition but increasing a memory consumption.

Roman Bartk; Pavel Surynek

2005-01-01T23:59:59.000Z

189

Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Program Documentation  

SciTech Connect

This document provides guidance to generator groups for preparing and maintaining documentation of Pollution Prevention/Waste Minimization (P2/WMin) Program activities. The guidance is one of a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan (DOE-RL, 2000) and Prime Contractor implementation plans describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994) and Department of Energy Acquisition Regulations (DEAR) (48 CFR 970.5204-2 and 48 CFR 970.5204-78). Documentation guidance for the following five P2/WMin elements is discussed: Fiscal Year (FY) Goals; Budget and Staffing; Pollution Prevention (P2) Reporting; WMin Certification; and Waste Minimization (WMin) Assessments (WMAs).

PLACE, B.G.

2000-11-01T23:59:59.000Z

190

Power Plant Baghouse Survey 2011  

Science Conference Proceedings (OSTI)

The requirement to reduce stack particulate matter (PM) emissions is one of the key challenges for coal-fired power plants, in light of the proposed Maximum Achievable Control Technology (MACT) ruling for hazardous air pollutants (HAPs) issued by the U.S. Environmental Protection Agency on March 16, 2011. The proposed MACT ruling may require that total PM, including condensable and filterable PM, be maintained at 0.03 lb/MMBtu. A final HAPs ruling is expected in December 2011. As particulate emission reg...

2011-12-06T23:59:59.000Z

191

Power Right. Power Smart. Efficient Computer Power Supplies and Monitors. |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Right. Power Smart. Efficient Computer Power Supplies and Power Right. Power Smart. Efficient Computer Power Supplies and Monitors. Power Right. Power Smart. Efficient Computer Power Supplies and Monitors. March 10, 2009 - 6:00am Addthis John Lippert Power supplies convert the AC power that you get from your electric company into the DC power consumed by most electronics, including your computer. We expect our power supplies to be safe, reliable, and durable. If they meet those criteria, then they're all alike, except for cost, right? Well, not exactly. You see, there's one other important feature that sets them apart: efficiency. And I don't know about you, but I believe waste is bad. For me, high efficiency is one important feature that's needed for something to be high quality. So isn't it ridiculous that most power

192

Power Right. Power Smart. Efficient Computer Power Supplies and Monitors. |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Right. Power Smart. Efficient Computer Power Supplies and Power Right. Power Smart. Efficient Computer Power Supplies and Monitors. Power Right. Power Smart. Efficient Computer Power Supplies and Monitors. March 10, 2009 - 6:00am Addthis John Lippert Power supplies convert the AC power that you get from your electric company into the DC power consumed by most electronics, including your computer. We expect our power supplies to be safe, reliable, and durable. If they meet those criteria, then they're all alike, except for cost, right? Well, not exactly. You see, there's one other important feature that sets them apart: efficiency. And I don't know about you, but I believe waste is bad. For me, high efficiency is one important feature that's needed for something to be high quality. So isn't it ridiculous that most power

193

Cyber Security Procurement Methodology for Power Delivery Systems  

Science Conference Proceedings (OSTI)

Determining how to apply cyber security requirements for new power delivery systems requires cyber security experts, power system engineers, and procurement organizations to work together with vendors to implement and maintain cyber security controls. Improper or incomplete implementation of controls due to lack of proper requirements and/or division of responsibilities between the utility and vendor can often result in costly backfit to meet requirements.The Electric Power Research ...

2012-12-31T23:59:59.000Z

194

Hybrid robust predictive optimization method of power system dispatch  

DOE Patents (OSTI)

A method of power system dispatch control solves power system dispatch problems by integrating a larger variety of generation, load and storage assets, including without limitation, combined heat and power (CHP) units, renewable generation with forecasting, controllable loads, electric, thermal and water energy storage. The method employs a predictive algorithm to dynamically schedule different assets in order to achieve global optimization and maintain the system normal operation.

Chandra, Ramu Sharat (Niskayuna, NY); Liu, Yan (Ballston Lake, NY); Bose, Sumit (Niskayuna, NY); de Bedout, Juan Manuel (West Glenville, NY)

2011-08-02T23:59:59.000Z

195

Power Supplies  

Science Conference Proceedings (OSTI)

Table 2   Characteristics of the four major power sources for induction heating...state 180 Hz to 50 kHz 1 kW to 2 MW 75??95 No standby current; high efficiency; no moving parts;

196

Objective 1: Extend Life, Improve Performance, and Maintain Safety of the Current Fleet Implementation Plan  

Science Conference Proceedings (OSTI)

Nuclear power has reliably and economically contributed almost 20% of electrical generation in the United States over the past two decades. It remains the single largest contributor (more than 70%) of non-greenhouse-gas-emitting electric power generation in the United States. By the year 2030, domestic demand for electrical energy is expected to grow to levels of 16 to 36% higher than 2007 levels. At the same time, most currently operating nuclear power plants will begin reaching the end of their 60 year operating licenses. Figure E 1 shows projected nuclear energy contribution to the domestic generating capacity. If current operating nuclear power plants do not operate beyond 60 years, the total fraction of generated electrical energy from nuclear power will begin to declineeven with the expected addition of new nuclear generating capacity. The oldest commercial plants in the United States reached their 40th anniversary in 2009. The U.S. Department of Energy Office of Nuclear Energys Research and Development (R&D) Roadmap has organized its activities in accordance with four objectives that ensure nuclear energy remains a compelling and viable energy option for the United States. The objectives are as follows: (1) develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current reactors; (2) develop improvements in the affordability of new reactors to enable nuclear energy to help meet the Administrations energy security and climate change goals; (3) develop sustainable nuclear fuel cycles; and (4) understand and minimize risks of nuclear proliferation and terrorism. The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1. This document describes how Objective 1 and the LWRS Program will be implemented. The existing U.S. nuclear fleet has a remarkable safety and performance record and today accounts for 70% of the low greenhouse gas emitting domestic electricity production. Extending the operating lifetimes of current plants beyond 60 years and, where possible, making further improvements in their productivity will generate early benefits from research, development, and demonstration investments in nuclear power. DOEs role in Objective 1 is to partner with industry and the Nuclear Regulatory Commission in appropriate ways to support and conduct the long-term research needed to inform major component refurbishment and replacement strategies, performance enhancements, plant license extensions, and age-related regulatory oversight decisions. The DOE research, development, and demonstration role will focus on aging phenomena and issues that require long-term research and are generic to reactor type. Cost-shared demonstration activities will be conducted when appropriate.

Robert Youngblood

2011-01-01T23:59:59.000Z

197

Objective 1: Extend Life, Improve Performance, and Maintain Safety of the Current Fleet Implementation Plan  

Science Conference Proceedings (OSTI)

Nuclear power has reliably and economically contributed almost 20% of electrical generation in the United States over the past two decades. It remains the single largest contributor (more than 70%) of non-greenhouse-gas-emitting electric power generation in the United States. By the year 2030, domestic demand for electrical energy is expected to grow to levels of 16 to 36% higher than 2007 levels. At the same time, most currently operating nuclear power plants will begin reaching the end of their 60 year operating licenses. Figure E 1 shows projected nuclear energy contribution to the domestic generating capacity. If current operating nuclear power plants do not operate beyond 60 years, the total fraction of generated electrical energy from nuclear power will begin to declineeven with the expected addition of new nuclear generating capacity. The oldest commercial plants in the United States reached their 40th anniversary in 2009. The U.S. Department of Energy Office of Nuclear Energys Research and Development (R&D) Roadmap has organized its activities in accordance with four objectives that ensure nuclear energy remains a compelling and viable energy option for the United States. The objectives are as follows: (1) develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current reactors; (2) develop improvements in the affordability of new reactors to enable nuclear energy to help meet the Administrations energy security and climate change goals; (3) develop sustainable nuclear fuel cycles; and (4) understand and minimize risks of nuclear proliferation and terrorism. The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1. This document describes how Objective 1 and the LWRS Program will be implemented. The existing U.S. nuclear fleet has a remarkable safety and performance record and today accounts for 70% of the low greenhouse gas emitting domestic electricity production. Extending the operating lifetimes of current plants beyond 60 years and, where possible, making further improvements in their productivity will generate early benefits from research, development, and demonstration investments in nuclear power. DOEs role in Objective 1 is to partner with industry and the Nuclear Regulatory Commission in appropriate ways to support and conduct the long-term research needed to inform major component refurbishment and replacement strategies, performance enhancements, plant license extensions, and age-related regulatory oversight decisions. The DOE research, development, and demonstration role will focus on aging phenomena and issues that require long-term research and are generic to reactor type. Cost-shared demonstration activities will be conducted when appropriate.

Robert Youngblood

2011-02-01T23:59:59.000Z

198

Bonneville Power Administration's YouTube Channel  

DOE Data Explorer (OSTI)

The Bonneville Power Administration is one of DOE's four power marketing administration organizations. BPA describes its mission as a public service organization as one designed create and deliver the best value for our customers and constituents as we act in concert with others to assure the Pacific Northwest: 1) An adequate, efficient, economical and reliable power supply; 2) A transmission system that is adequate to the task of integrating and transmitting power from federal and non-federal generating units, providing service to BPA's customers, providing interregional interconnections, and maintaining electrical reliability and stability; and 3) Mitigation of the Federal Columbia River Power System's impacts on fish and wildlife. The more than 100 videos on BPA's YouTube channel are organized into 12 playlists, including: Technology R&D, Renewable Energy, Hydropower, Energy Efficiency and Conservation, Transmission, Environment, Fish, and Wildlife, Vegetation Management and Public Safety, Value of the River Education Series, and Community and Education.

199

IEEE POWER ENGINEERING SOCIETY GENERAL MEETING, PITTSBURGH, PA USA JULY 2008 1 Initial review of methods for cascading failure  

E-Print Network (OSTI)

of methods for cascading failure analysis in electric power transmission systems IEEE PES CAMS Task Force. The vital importance of electric power to our society motivates continued attention to maintaining power the power system. This definition is consistent with the usage in [10]. It differs from [75], who limit

Dobson, Ian

200

Maintaining Electrical System Reliability Under a Closed-Cycle Cooling Retrofit Requirement  

Science Conference Proceedings (OSTI)

The Electric Power Research Institute (EPRI) is investigating the implications of a potential U.S. Environmental Protection Agency (EPA) Clean Water Act 316(b) rulemaking that would establish "best technology available" (BTA) based on closed-cycle cooling retrofits for facilities with once-through cooling. This report focuses on the transmission system impacts that can potentially result from a requirement for use of closed-cycle cooling systems.

2011-07-20T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Power superconducting power transmission cable  

DOE Patents (OSTI)

The present invention is for a compact superconducting power transmission cable operating at distribution level voltages. The superconducting cable is a conductor with a number of tapes assembled into a subconductor. These conductors are then mounted co-planarly in an elongated dielectric to produce a 3-phase cable. The arrangement increases the magnetic field parallel to the tapes thereby reducing ac losses.

Ashworth, Stephen P. (Cambridge, GB)

2003-01-01T23:59:59.000Z

202

Autonomous uninterruptible power-supply apparatus  

SciTech Connect

This invention relates broadly to a power supply apparatus, and in particular to an autonomous uninterruptible power supply apparatus. The purpose of an uninterruptible power supply (UPS) is to protect critical electrical loads from transient or steady-stage outages or disturbances in the primary power source. The basic configuration of a typical, commercially available, uninterruptible power supply is comprised at a minimum of a standby battery and a battery charger and may also include an inverter for AC applications. Systems of this type can be found in most computer installations and laboratory systems that cannot tolerate even momentary disturbances of input power. This document describes an autonomous uninterruptible power-supply apparatus utilizing a digital-processor unit as a control and monitor unit to measure and control input and output parameters in the power supply. A battery charger is utilized to maintain the voltage and current levels with the backup battery supply source which powers an inverter unit that converts the DC power to an AC output.

Masson, J.H.

1984-12-20T23:59:59.000Z

203

Quantification of Hungry Horse Reservoir Water Levels Needed to Maintain or Enhance Reservoir Fisheries; Methods and Data, 1983-1987 Summary Report.  

Science Conference Proceedings (OSTI)

The Hungry Horse Reservoir study is part of the Northwest Power Planning Council's resident fish and wildlife plan. The plan is responsible for mitigating damages to the fish and wildlife resources caused by hydroelectric development in the Columbia River Basin. The major goal of our study is to quantify seasonal water levels needed to maintain or enhance the reservoir fishery. This study began in May, 1983, and the initial phase will be completed July, 1988. This report summarizes limnological, fish abundance, fish distribution and fish food habits data collected from 1983 to 1988. The effect of reservoir operation upon fish habitat, fish food organisms and fish growth is discussed. 71 refs., 36 figs., 46 tabs.

May, Bruce; Michael, Gary; Wachsmuth, John (Montana Department of Fish, Wildlife and Parks, Kalispell, MT)

1988-06-01T23:59:59.000Z

204

Voltage quality behaviour of a wind turbine based Remote Area Power System  

Science Conference Proceedings (OSTI)

The power quality behaviour of a Remote Area Power System (RAPS) consisting of a Doubly Fed Induction Generator (DFIG), its main loads and a dummy load is presented in this paper. The dummy load is used to maintain the power balance of the system under ...

Nishad Mendis; Kashem M. Muttaqi; Sarath Perera

2009-02-01T23:59:59.000Z

205

Steady-state power flow modeling for a dynamic voltage restorer  

Science Conference Proceedings (OSTI)

This paper presents analysis, modeling and simulation of power distribution network performance incorporating with an installed dynamic voltage restorer (DVR). DVR is one of series compensators used in power distribution systems in order to maintain ... Keywords: Gauss-Seidel method, dynamic voltage restorer, modeling, power flow, simulation

T. Ratniyomchai; T. Kulworawanichpong

2006-03-01T23:59:59.000Z

206

EPRI Power Electronics-Based Transmission Controllers Reference Book ("The Gold Book")  

Science Conference Proceedings (OSTI)

EPRI is sponsoring development of a first edition of the EPRI Power Electronics-Based Transmission Controllers Reference Book. This report is the most recent draft of a chapter for the "Gold Book," an authoritative guide for utilities and others who install and maintain power electronics equipment to increase power transfer capability.

2009-12-23T23:59:59.000Z

207

Nuclear Power  

E-Print Network (OSTI)

The world of the twenty first century is an energy consuming society. Due to increasing population and living standards, each year the world requires more energy and new efficient systems for delivering it. Furthermore, the new systems must be inherently safe and environmentally benign. These realities of today's world are among the reasons that lead to serious interest in deploying nuclear power as a sustainable energy source. Today's nuclear reactors are safe and highly efficient energy systems that offer electricity and a multitude of co-generation energy products ranging from potable water to heat for industrial applications. The goal of the book is to show the current state-of-the-art in the covered technical areas as well as to demonstrate how general engineering principles and methods can be applied to nuclear power systems.

Tsvetkov, Pavel

2010-08-01T23:59:59.000Z

208

Power supply  

SciTech Connect

An electric power supply employs a striking means to initiate ferroelectric elements which provide electrical energy output which subsequently initiates an explosive charge which initiates a second ferroelectric current generator to deliver current to the coil of a magnetic field current generator, creating a magnetic field around the coil. Continued detonation effects compression of the magnetic field and subsequent generation and delivery of a large output current to appropriate output loads.

Hart, Edward J. (Albuquerque, NM); Leeman, James E. (Albuquerque, NM); MacDougall, Hugh R. (Albuquerque, NM); Marron, John J. (Albuquerque, NM); Smith, Calvin C. (Amarillo, TX)

1976-01-01T23:59:59.000Z

209

Power Search  

NLE Websites -- All DOE Office Websites (Extended Search)

You are here: Find a Car Home > Power Search You are here: Find a Car Home > Power Search Power Search Expand any feature by selecting its title bar. Choose as many or as few features as you like. Model Year From: 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984 To: 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984 MSRP Under $15,000 $15,000-$20,000 $20,000-$25,000 $25,000-$30,000 $30,000-$35,000 $35,000-$40,000 $40,000-$45,000 $45,000-$50,000 $50,000-$55,000 $55,000-$60,000 $60,000-$65,000 $65,000-$70,000 $70,000-$75,000 $75,000-$80,000 $80,000-$85,000 Over $85,000 - OR - Minimum: Select... $5,000 $6,000 $7,000 $8,000 $9,000 $10,000 $11,000

210

METRO Metropolitan Exposition Recreation Commission MERC Facilities Efficiently Maintained Maybe Too Efficiently  

E-Print Network (OSTI)

To the Metro Council, Metropolitan Exposition Recreation Commission and Metro-area citizens: As part of the Metro Auditors risk assessment and audit plan, we studied facility care and capital improvement processes at the Metropolitan Exposition Recreation Commission (MERC), a unit of Metro. Facility care includes janitorial and repair and maintenance activities. Capital improvement processes include plans for determining necessary capital improvements and obtaining adequate, reliable funding for capital renewal and replacement projects. MERC owns public assembly facilities with a book value of over $200 million. It manages the Oregon Convention Center, the Portland Center for the Performing Arts and the Portland Metropolitan Exposition Center. The cost of maintaining and safeguarding these facilities consumes about 14 % of MERCs operating revenues each year. The cost of MERC facilities care activities benchmark below that of other facilities across the nation. While low cost is generally a positive, some improvements in facility care practices and capital improvement processes could be made. We recommend that MERC: Evaluate the adequacy of staffing for janitorial and maintenance activities and add electrical expertise where needed.

Alexis Dow Cpa; A Uditor; A Lexis; D Ow

2006-01-01T23:59:59.000Z

211

Definition and Means of Maintaining the Criticality Prevention Design Features Portion of the PFP Safety Envelope  

SciTech Connect

The purpose of this document is to record the technical evaluation of the Operational Safety Requirements described in the Plutonium Finishing Plant Final (PFP) Operational Safety Requirements, WHC-SD-CP-OSR-010. Rev. 0-N , Section 3.1.1, ''Criticality Prevention System.'' This document, with its appendices, provides the following: (1) The results of a review of Criticality Safety Analysis Reports (CSAR), later called Criticality Safety Evaluation Reports (CSER), and Criticality Prevention Specifications (CPS) to determine which equipment or components analyzed in the CSER or CPS are considered as one of the two unlikely, independent, and concurrent changes before a criticality accident is possible. (2) Evaluations of equipment or components to determine the safety boundary for the system (Section 4). (3) A list of essential drawings that show the safety system or component (Appendix A). (4) A list of the safety envelope (SE) equipment (Appendix B). (5) Functional requirements for the individual safety envelope equipment (Sections 3 and 4). (6) A list of the operational and surveillance procedures necessary to maintain the system equipment within the safety envelope (Section 5).

RAMBLE, A.L.

2000-07-28T23:59:59.000Z

212

Interaction of LEAFY, AGAMOUS, and TERMINAL FLOWER1 in maintaining floral identity in Arabidopsis  

SciTech Connect

OAK-B135 The Arabidopsis transcription factor LEAFY (LFY) acts upstream of homeotic genes such as AGAMOUS (AG) to confer floral identity on meristems that arise after the transition to reproductive development. Compared to the genetic circuitry regulating the establishment of floral meristem identity, little is known about its maintenance. Previous experiments with fly heterozygous plants and ag mutants grown in conditions that reduce the floral inductive stimulus have shown that both genes are required to prevent reversion of floral to inflorescence meristems. Here, we present evidence that LFY maintains floral meristem identity independently of AG, and that the primary role of LFY is either direct repression of shoot identity genes or repression of an intermediate factor that activates shoot identity genes. The latter conclusions were deduced from the phenotypes conferred by a gain-of-function transgene, LFY:VP16, that appears to act as a dominant negative, or antimorphic, allele during maintenance of floral meristem identity. These observations contrast with previous findings that LFY acts as a direct activator of floral homeotic genes, supporting the hypothesis that the transcriptional activity of LFY is dependent on specific co-regulators.

Parcy, F., Bomblies, K., and Weigel, D.

2002-02-22T23:59:59.000Z

213

Assessing the influence of import-coupling on OCL expression maintainability: A cognitive theory-based perspective  

Science Conference Proceedings (OSTI)

The aim of this paper is to present the definition of the measures for the import-coupling of OCL expressions, along with the empirical validation of these as early indicators of the maintainability of OCL expressions. This empirical validation has been ... Keywords: Cognitive models, Comprehensibility, Experiments, Import-coupling, Maintainability, Mental models, Meta-analysis, Modifiability, OCL expressions, Software measures, UML/OCL models

Luis Reynoso; Esperanza Manso; Marcela Genero; Mario Piattini

2010-10-01T23:59:59.000Z

214

Bulk Power Transmission Study  

E-Print Network (OSTI)

"Texans now have a choice. We can become more efficient and maintain our standard of living, or we can continue business as usual and watch our standard of living erode from competition from other regions. In the past, except for improving reliability, there was no need for a strong transmission system. When Texas generation was primarily gas fueled, the extensive natural gas pipeline network moved energy easily within the state. In recent years two things have changed: 1. Electric utilities have made extensive investment in lignite, coal, and nuclear plants and, 2. Improvements in gas turbine technology and the removal of institutional barriers has encouraged cogeneration at many of our energy intensive process industries. This energy diversity means that there are now significant differences in energy costs between units. The variable costs of generation of power can vary between units by a ratio of 2 or 3 to 1 and this difference will be accentuated when energy costs rise (and they will; its a question of when, not if). The potential for costs savings by optional dispatching of the entire interconnected system are greater than ever before as demonstrated by the PUC's Bulk Power Transmission Study. And the potential can be enhanced with added transmission system investment. Cogeneration and small power production has proven to be the most cost effective way for Texas to add additional generating capacity needed to supply an economy that is starting to rebound and to replace old, obsolete power plants. The freedom to locate these facilities at the fuel source or at the site of large thermal demand makes real economic and environmental sense. The use of renewable or waste fuels allows something that would otherwise be wasted to contribute to our economy. Fossil fuels that are displaced can be redirected to another use or consumed for future benefit. By integrating a gas turbine generator with a. process plant, the natural gas required for producing electricity can be reduced by 40% below that required for a combined cycle. The heat rejected from a gas turbine, combined cycle, or steam plant can be redirected to a process use that contributes to our economy by producing something of value to world markets. By contrast a conventional power plant is paid for by the rate payers and consumes Texas natural resources and therefore is a burden rather than an enhancement to our economy. The optimal location of facilities are possible only if there is an adequate transmission system. Utility, consumer and industry must cooperate to improve our transmission system for the benefit of all Texas. The Texas Public Utilities Commission has taken the lead in promoting efficiency by requiring transmission wheeling between qualifying facilities and electric utilities. Several cogeneration facilities have been constructed as a result. In order to encourage small power production, the rule needs to be expanded to include projects interconnected with distribution systems. Most renewable resource projects are relatively small and cannot afford the cost of a high voltage interconnect, and yet their characteristics match a baseload need. The ability to wheel power to a utility that needs base load power from a distribution level interconnection is essential to development of these smaller projects."

John, T.

1988-09-01T23:59:59.000Z

215

Power Electronics Reliability Kick Off Meeting … Silicon Power Corp. & Sandia Labs  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reliability Reliability Analysis Annual DOE Peer Review Meeting October 8, 2009 Mark A. Smith - Systems Readiness & Sustainment Technologies Department Stan Atcitty - Energy Infrastructure and Distributed Energy Resources Department Sandia National Laboratories Technologies & Customers * Complex Systems Modeling & Simulation * Life Cycle & Total Ownership Costs Analyses * Design for Reliability/Maintainability * Prognostics & Health Management (PHM) * Integrated Logistics Support * Technology Management Optimization * Asset Acquisition & Mission Planning * Risk Assessment & Risk Management Technologies Support Broad Customer Base Automotive Power Electronics Aviation Nuclear Power Coal-Fired Power Petroleum Tools & Technologies Validated Through Broad Use

216

Effect of soiling on solar mirrors and techniques used to maintain high reflectivity  

DOE Green Energy (OSTI)

Solar mirrors are used to concentrate low-level solar radiation to power levels which are practical and efficient for consumption. Any interference with the collection of that energy not only decreases the power level but also increases the cost of the energy available from a solar power system. One of the most immediate and drastic effects of outdoor exposure is the reflectance loss due to the accumulation of foreign particles on the mirror surface. Specular reflectance losses as great as 25% have been observed for mirrors exposed for only a few weeks. The effect of the deposited particles is to reduce the reflected energy by both absorbing and scattering light. The degree to which the particles reduce the collection of reflected energy depends on their composition, number and size distribution. An additional factor is the optics of the collection system. The angular acceptance aperture of the system, defined as the angle subtended by the receiver at the concentrator surface, determines the relative importance of the scattering due to dust accumulation. For flat plate thermal and photovoltaic collectors which have essentially a 180/sup 0/ angular acceptance aperture, scattering of the incident light is not critical but absorption can be an important factor in the loss of energy. For concentrating collection systems, such as line focus collectors and central receivers, angular acceptance apertures of a few degrees make scattering at the concentrator surface much more important and can result in severe energy losses. Results of a study of each of these areas are presented and discussed. (WHK)

Roth, E.P.; Pettit, R.B.

1980-06-01T23:59:59.000Z

217

Quantification of Libby Reservoir Levels Needed to Maintain or Enhance Reservoir Fisheries, 1985 Annual Report.  

DOE Green Energy (OSTI)

The goal was to quantify seasonal water levels needed to maintain or enhance the reservoir fishery in Libby. This report summarizes data collected from July 1984 through July 1985, and, where appropriate, presents data collected since 1983. The Canada, Rexford, and Tenmile areas of the reservoir are differentially affected by drawdown. Relative changes in water volume and surface area are greatest in the Canada area and smallest in the Tenmile area. Reservoir morphology and hydraulics probably play a major role in fish distribution through their influence on water temperature. Greatest areas of habitat with optimum water temperature for Salmo spp. and kokanee occurred during the spring and fall months. Dissolved oxygen, pH and conductivity levels were not limiting during any sampling period. Habitat enhancement work was largely unsuccessful. Littoral zone vegetation plantings did not survive well, primarily the result of extreme water level fluctuations. Relative abundances of fish species varied seasonally within and between the three areas. Water temperature is thought to be the major influence in fish distribution patterns. Other factors, such as food availability and turbidity, may mitigate its influence. Sampling since 1975 illustrates a continued increase in kokanee numbers and a dramatic decline in redside shiners. Salmo spp., bull trout, and burbot abundances are relatively low while peamouth and coarsescale sucker numbers remain high. A thermal dynamics model and a trophic level components model will be used to quantify the impact of reservoir operation on the reservoir habitat, primary production, secondary production and fish populations. Particulate carbon will be used to track energy flow through trophic levels. A growth-driven population dynamics simulation model that will estimate the impacts of reservoir operation on fish population dynamics is also being considered.

Chisholm, Ian

1985-01-01T23:59:59.000Z

218

Long term control of 3D engineering data for nuclear power plants  

Science Conference Proceedings (OSTI)

The engineering of the next generation of nuclear power plants requires to take into account the whole plant lifecycle: engineering, building, operating, maintaining and decommissioning. Satisfying stronger and stronger safety regulations requires the ...

Thomas Paviot; Christophe Mouton; Samir Lamouri

2013-06-01T23:59:59.000Z

219

Evaluation of high power density annular fuel application in the Korean OPR-1000 reactor  

E-Print Network (OSTI)

Compared to the traditional solid fuel geometry for PWRs, the internally and externally cooled annular fuel offers the potential to increase the core power density while maintaining or increasing safety margins. It is ...

Zhang, Liang, S.M. Massachusetts Institute of Technology

2009-01-01T23:59:59.000Z

220

A survey on wind power ramp forecasting.  

DOE Green Energy (OSTI)

The increasing use of wind power as a source of electricity poses new challenges with regard to both power production and load balance in the electricity grid. This new source of energy is volatile and highly variable. The only way to integrate such power into the grid is to develop reliable and accurate wind power forecasting systems. Electricity generated from wind power can be highly variable at several different timescales: sub-hourly, hourly, daily, and seasonally. Wind energy, like other electricity sources, must be scheduled. Although wind power forecasting methods are used, the ability to predict wind plant output remains relatively low for short-term operation. Because instantaneous electrical generation and consumption must remain in balance to maintain grid stability, wind power's variability can present substantial challenges when large amounts of wind power are incorporated into a grid system. A critical issue is ramp events, which are sudden and large changes (increases or decreases) in wind power. This report presents an overview of current ramp definitions and state-of-the-art approaches in ramp event forecasting.

Ferreira, C.; Gama, J.; Matias, L.; Botterud, A.; Wang, J. (Decision and Information Sciences); (INESC Porto)

2011-02-23T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Solar Power Fact Book: Third Edition  

Science Conference Proceedings (OSTI)

EPRI maintains and updates a database of commonly requested technical information on photovoltaic (PV) and concentrating solar thermal power (CSP) technologies. The database addresses cost and performance, resource assessment, project siting and development, environmental impacts, policy and market drivers, and other relevant issues. The data and information have been compiled into this fact book, building on and complementing the annual Renewable Energy Technology GuideRETG, ...

2012-12-31T23:59:59.000Z

222

Low Power Design Low PowerLow Power  

E-Print Network (OSTI)

, correlations among system state transitions #12;Low Power Design USC/LPCAD Page 11 USCUSC Low PowerLow Power for the requestsIncoming rates for the requests 21,rr 12 ,rr, :, : State transition ratesState transition rates OS and hardware Abstract, hierarchical finite-state machine Each state represents power

Pedram, Massoud

223

Switching power pulse system  

DOE Patents (OSTI)

A switching system for delivering pulses of power from a source to a load using a storage capacitor charged through a rectifier, and maintained charged to a reference voltage level by a transistor switch and voltage comparator. A thyristor is triggered to discharge the storage capacitor through a saturable reactor and fractional turn saturable transformer having a secondary to primary turn ratio N of n:l/n = n[sup 2]. The saturable reactor functions as a soaker'' while the thyristor reaches saturation, and then switches to a low impedance state. The saturable transformer functions as a switching transformer with high impedance while a load coupling capacitor charges, and then switches to a low impedance state to dump the charge of the storage capacitor into the load through the coupling capacitor. The transformer is comprised of a multilayer core having two secondary windings tightly wound and connected in parallel to add their output voltage and reduce output inductance, and a number of single turn windings connected in parallel at nodes for the primary winding, each single turn winding linking a different one of the layers of the multilayer core. The load may be comprised of a resistive beampipe for a linear particle accelerator and capacitance of a pulse forming network. To hold off discharge of the capacitance until it is fully charged, a saturable core is provided around the resistive beampipe to isolate the beampipe from the capacitance until it is fully charged. 5 figs.

Aaland, K.

1983-08-09T23:59:59.000Z

224

Southwestern Power Administration One West Third Street  

NLE Websites -- All DOE Office Websites (Extended Search)

Department of Energy Department of Energy Southwestern Power Administration One West Third Street Tulsa, Oklahoma 74103-3502 December 2, 2008 ENVIRONMENTAL POLICY STATEMENT The Environmental Policy is the driver for implementing and improving Southwestern Power Administration's (Southwestern) Environmental Management System so that Southwestern can maintain and improve environmental performance. The policy reflects the commitment of top management to comply with applicable legal and other requirements, to prevent pollution and to continually improve. Southwestern's Environmental Policy forms the basis upon which its Environmental Objectives and Targets are established. Southwestern's senior management has committed in writing the following Environmental Policy:

225

Maintaining Generation Adequacy in a Restructuring U.S. Electricity Industry  

SciTech Connect

Historically, decisions on the amounts, locations, types, and timing of investments in new generation have been made by vertically integrated utilities with approval from state public utility commissions. As the U.S. electricity industry is restructured, these decisions are being fragmented and dispersed among a variety of organizations. As generation is deregulated and becomes increasingly competitive, decisions on whether to build new generators and to retire, maintain, or repower existing units will increasingly be made by unregulated for-profit corporations. These decisions will be based largely on investor assessments of future profitability and only secondarily on regional reliability requirements. In addition, some customers will choose to face real-time (spot) prices and will respond to the occasionally very high prices by reducing electricity use at those times. Market-determined generation levels will, relative to centrally mandated reserve margins, lead to: (1) more volatile energy prices; (2) lower electricity costs and prices; and (3) a generation mix with more baseload, and less peaking, capacity. During the transition from a vertically integrated, regulated industry to a deintegrated, competitive industry, government regulators and system operators may continue to impose minimum-installed-capacity requirements on load-serving entities. As the industry gains experience with customer responses to real-time pricing and with operation of competitive intrahour energy markets, these requirements will likely disappear. We quantitatively analyzed these issues with the Oak Ridge Competitive Electricity Dispatch model (ORCED). Model results show that the optimal reserve margin depends on various factors, including fuel prices, initial mix of generation capacity, and customer response to electricity prices (load shapes and system load factor). Because the correct reserve margin depends on these generally unpredictable factors, mandated reserve margins might be too high, leading to higher electricity costs and prices. Absent mandated reserve margins, electricity prices and costs decline with increasing customer response to prices during high-demand periods. The issues discussed here are primarily transitional rather than enduring. However, the transition from a highly regulated, vertically integrated industry to one dominated by competition is likely to take another five to ten years.

Hirst, E.; Hadley, S.

1999-10-01T23:59:59.000Z

226

International Energy Outlook 1999 - Nuclear Power  

Gasoline and Diesel Fuel Update (EIA)

nuclear.jpg (5137 bytes) nuclear.jpg (5137 bytes) Nuclear electricity generation remains flat in the IEO99 reference case, representing a declining share of the world’s total electricity consumption. Net reductions in nuclear capacity are projected for most industrialized nations. In 1997, a total of 2,276 billion kilowatthours of electricity was generated from nuclear power worldwide, providing 17 percent of the world’s electricity generation. Among the countries with operating nuclear power plants, national dependence on nuclear power for electricity varies greatly (Figure 53). Ten countries met at least 40 percent of their total electricity demand with generation from nuclear reactors. The prospects for nuclear power to maintain a significant share of worldwide electricity generation are uncertain, despite projected growth of

227

Power management system  

DOE Patents (OSTI)

A method of managing power resources for an electrical system of a vehicle may include identifying enabled power sources from among a plurality of power sources in electrical communication with the electrical system and calculating a threshold power value for the enabled power sources. A total power load placed on the electrical system by one or more power consumers may be measured. If the total power load exceeds the threshold power value, then a determination may be made as to whether one or more additional power sources is available from among the plurality of power sources. At least one of the one or more additional power sources may be enabled, if available.

Algrain, Marcelo C. (Peoria, IL); Johnson, Kris W. (Washington, IL); Akasam, Sivaprasad (Peoria, IL); Hoff, Brian D. (East Peoria, IL)

2007-10-02T23:59:59.000Z

228

Solar powered desalination system  

E-Print Network (OSTI)

1.13: California Power Generation by Source31for hydro- electric power generation would be reached inother end users include the power generation industry (4%),

Mateo, Tiffany Alisa

2011-01-01T23:59:59.000Z

229

Solar powered desalination system  

E-Print Network (OSTI)

2008, uses concentrated solar power to split water. Figurethe main reason the potential for solar power is boundless.a clean energy source, solar power is inexhaustible, fairly

Mateo, Tiffany Alisa

2011-01-01T23:59:59.000Z

230

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

POTC Home Courses Instructors NERC Continuing Education Virtual University Power Operations Training Center You'll find the "Power" of learning at Southwestern's Power Operations...

231

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

Schedules Skip Navigation Links Excess Energy Hydro Peaking Power Hydro Power and Energy Sold to Sam Rayburn Dam Electric Cooperative (Rayburn) Hydro Power and Energy Sold to Sam...

232

Hybrid-Intelligent POWER HI-POWER  

Science Conference Proceedings (OSTI)

... T T T A A A SMART-T Current Situation Current Situation ... Page 10. 22 Power Grid Plug & Play architecture Multiple power sources Renewables ...

2013-09-22T23:59:59.000Z

233

POWER REACTOR  

DOE Patents (OSTI)

A fast nuclear reactor system ls described for producing power and radioactive isotopes. The reactor core is of the heterogeneous, fluid sealed type comprised of vertically arranged elongated tubular fuel elements having vertical coolant passages. The active portion is surrounded by a neutron reflector and a shield. The system includes pumps and heat exchangers for the primary and secondary coolant circuits. The core, primary coolant pump and primary heat exchanger are disposed within an irapenforate tank which is filled with the primary coolant, in this case a liquid metal such as Na or NaK, to completely submerge these elements. The tank is completely surrounded by a thick walled concrete shield. This reactor system utilizes enriched uranium or plutonium as the fissionable material, uranium or thorium as a diluent and thorium or uranium containing less than 0 7% of the U/sup 235/ isotope as a fertile material.

Zinn, W.H.

1958-07-01T23:59:59.000Z

234

Power oscillator  

DOE Patents (OSTI)

An oscillator includes an amplifier having an input and an output, and an impedance transformation network connected between the input of the amplifier and the output of the amplifier, wherein the impedance transformation network is configured to provide suitable positive feedback from the output of the amplifier to the input of the amplifier to initiate and sustain an oscillating condition, and wherein the impedance transformation network is configured to protect the input of the amplifier from a destructive feedback signal. One example of the oscillator is a single active element device capable of providing over 70 watts of power at over 70% efficiency. Various control circuits may be employed to match the driving frequency of the oscillator to a plurality of tuning states of the lamp.

Gitsevich, Aleksandr (Montgomery Village, MD)

2001-01-01T23:59:59.000Z

235

Power plant  

SciTech Connect

A two stroke internal combustion engine is described that has at least one cylinder within which a piston reciprocates. The engine is joined to a gearbox which includes a ring gear. A pair of gears having diameters half that of the ring gear move within the latter. At least one of the pair of gears is connected to a piston by a pin extending between the piston and the periphery of said gear. An additional pair of gears are fixed to respective ones of the first-mentioned gear pair and are operatively joined to a pinion to which a drive shaft is secured. A turbine and filter arrangement is positioned on the side of the engine opposite the gearbox whereby exhaust gases from the engine are directed to the turbine to develop power at an output drive shaft joined to the turbine and to filter pollutants from the gases.

Finn, H.I. Jr.

1978-10-24T23:59:59.000Z

236

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Carlos Apache Tribe Carlos Apache Tribe San Carlos Apache Mission Statement The Apache People will live a balanced life in harmony with spirituality, culture, language, and family unity in an ever-changing world. The Apache People shall create a strategic framework for our tribe to grow and prosper. San Carlos Apache Tribe And Reservation * Membership: approx 15,000 * Unemployment rate: 67% * 11 member tribal council * Apache Gold Casino * 1.83 million acres. * 800,000+ acres wooded/forested. * 1M ac. riparian/ grasslands/desert. * 2nd highest rated level of solar resource potential San Carlos Apache Reservation S a n C a r l o s A p a c h e T r i b e 2008 - 2013 Energy Initiatives * 2008: DOE ARRA Energy grant (TA/Energy Plan/lighting retrofits, solar at radio station/1 st

237

Audit of Funding for Advanced Radioisotope Power Systems, IG-0413  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

October 17, 1997 October 17, 1997 MEMORANDUM FOR THE SECRETARY FROM: John C. Layton Inspector General SUBJECT: INFORMATION: "Audit of Funding for Advanced Radioisotope Power Systems" BACKGROUND: The Department of Energy's (Department) Advanced Radioisotope Power Systems Program maintains the sole national capability and facilities to produce radioisotope power systems for the National Aeronautics and Space Administration (NASA), the Department of Defense, and other Federal agencies. For the past seven years the program emphasis has been on providing power systems for NASA's Cassini mission to Saturn, which was launched earlier this month. We initiated this audit to determine whether the

238

Report on audit of funding for advanced radioisotope power systems  

Science Conference Proceedings (OSTI)

The U.S. Department of Energy`s (Department) Advanced Radioisotope Power Systems Program maintains the sole national capability and facilities to produce radioisotope power systems for the National Aeronautics and Space Administration (NASA), the Department of Defense, and other Federal agencies. Projects are conducted with these agencies in accordance with written agreements and are dependent on cost sharing by the user agencies. For the past seven years the program emphasis has been on providing power systems for NASA`s Cassini mission to Saturn, which was launched earlier this month. We initiated this audit to determine whether the Department received proper reimbursement from NASA for the radioisotope power systems produced.

NONE

1997-10-17T23:59:59.000Z

239

The NASA CSTI High Capacity Power Project  

SciTech Connect

The SP-100 Space Nuclear Power Program was established in 1983 by DOD, DOE, and NASA as a joint program to develop technology for military and civil applications. Starting in 1986, NASA has funded a technology program to maintain the momentum of promising aerospace technology advancement started during Phase I of SP-100 and to strengthen, in key areas, the changes for successful development and growth capability of space nuclear reactor power systems for a wide range of future space applications. The elements of the CSTI High Capacity Power Project include Systems Analysis, Stirling Power Conversion, Thermoelectric Power Conversion, Thermal Management, Power Management, Systems Diagnostics, Environmental Interactions, and Material/Structural Development. Technology advancement in all elements is required to provide the growth capability, high reliability and 7 to 10 year lifetime demanded for future space nuclear power systems. The overall project with develop and demonstrate the technology base required to provide a wide range of modular power systems compatible with the SP-100 reactor which facilitates operation during lunar and planetary day/night cycles as well as allowing spacecraft operation at any attitude or distance from the sun. Significant accomplishments in all of the project elements will be presented, along with revised goals and project timelines recently developed.

Winter, J.; Dudenhoefer, J.; Juhasz, A.; Schwarze, G.; Patterson, R.; Ferguson, D.; Titran, R. [National Aeronautics and Space Administration, Cleveland, OH (United States). Lewis Research Center; Schmitz, P. [Sverdrup Technology, Inc., Brook Park, OH (United States). Lewis Research Center Group; Vandersande, J. [Jet Propulsion Lab., Pasadena, CA (United States)

1994-09-01T23:59:59.000Z

240

Quantification of Libby Reservoir Water Levels Needed to Maintain or Enhance Reservoir Fisheries, 1983 Final Report.  

DOE Green Energy (OSTI)

The first six months of the fishery investigations in Libby Reservoir were aimed at developing suitable methodology for sampling physical-chemical limnology, fish food availability, fish food habits, and seasonal distribution and abundance of fish populations. Appropriate methods have been developed for all aspects with minor modification of original proposed methodologies. Purse seining has yet to be tested. Physical-chemical limnologic sampling could be reduced or subcontracted with the U.S. Geologic Survey to allow for more intensive sampling of fish food or fish distribution portions of the investigation. Final sample design will be determined during 1983-84. Future directions of the study revolve around two central issues, the potential for flexibility in reservoir operation and determination of how reservoir operation affects fish populations. Simulated maximum drawdown levels during a 40-year period were controlled by power in seven out of eight years. Drawdowns were generally within 10 feet of the flood control rule curve, however. There may be more flexibility with regards to timing of refill and evacuation. This aspect needs to be evaluated further. Production and availability of fish food, suitability of reservoir habitat, and accessibility of off-reservoir spawning and rearing habitat were identified as components of fish ecology which reservoir operation could potentially impact. Two models based on trophic dynamics and habitat suitabilities were suggested as a framework for exploring the relationship of reservoir operation on the fish community.

Shepard, Bradley B.

1984-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Electric Power Annual  

U.S. Energy Information Administration (EIA)

Electric Power Sector ; Period Total (all sectors) Electric Utilities Independent Power Producers Commercial Sector Industrial Sector; Annual Totals: ...

242

Electric Power Metrology Portal  

Science Conference Proceedings (OSTI)

... Electric Power Metrology and the Smart Grid Our country's way of life depends on the electric power distribution system. ...

2012-12-26T23:59:59.000Z

243

Putting Economic Power in Distributed Power  

Reports and Publications (EIA)

Electric Power Research Institute's Distributed Resources Week 1997 (October 22, 1997)AUTHOR: John Herbert

Information Center

1997-10-22T23:59:59.000Z

244

Proof of feasibility of a novel inverter for photovoltaic power conditioning  

SciTech Connect

The Dickerson inverter concept obtains a sinewave current from an array that is segmented into a number of subarrays. These subarrays are switched among the ac phases so that the current from a given subarray is continuous and each phase is connected at all times to one or more subarrays. The control scheme assures a unity power factor currrent with real-time adjustment to power-system disturbances. A proof-of-concept inverter has been operated into a three-phase power system, with the dc supplied from a motor-generator set plus regulators that closely simulated the current-voltage characteristics of a photovoltaic array. The performance for the inverter has been projected for a 480V, three-phase system at the 50 kVA level. Computer simulations showed 98% utilization of array power was possible with efficiency better than 98% and harmonic content of 18% without filtering. An analysis of filtering costs indicates that reduction to 5% can be achieved at under $0.003 per watt for typical central-station applications. A more complex configuration was also analyzed with results of 99% utilization, 8% harmonic content, and the same efficiency. The intended power range for these inverters is 50 to 250 kVA per unit. The cost to produce the inverter at the 50 kVA level in quantities of 1000 units is estimated to be $0.05 per watt.

Dickerson, A.

1986-04-01T23:59:59.000Z

245

Combined gas turbine and steam turbine power plant  

SciTech Connect

A description is given of a power plant arrangement having a gas turbine, a heat recovery steam generator, a steam turbine and means for controlling steam flow from the heat recovery steam generator to the steam turbine. Steam conditions are maintained generally constant and variations in power plant loading are carried by the steam turbine while operating the gas turbine at a generally constant fuel flow.

Baker, J.M.; Clark, G.W.; Harper, D.M.; Tomlinson, L.O.

1978-04-04T23:59:59.000Z

246

Framework for Grading Procurement Requirements for Power Delivery Systems  

Science Conference Proceedings (OSTI)

Determining how to apply cyber security requirements for new power delivery systems requires cyber security experts, power system engineers, and procurement organizations to work together with vendors to select, implement, and maintain cyber security controls. Improper or incomplete implementations of security controls due to a lack of adequate requirements and/or division of responsibilities between the utility and vendor can often result in costly back fit to meet requirements.This ...

2013-11-27T23:59:59.000Z

247

Ergonomic Design Handbook for Fossil-Fueled Electric Power Plants  

Science Conference Proceedings (OSTI)

Workers in power plants are exposed to numerous risk factors for musculoskeletal disorders (MSDs). This report addresses those issues of accessibility and maintainability affecting MSDs that can best be addressed in the design phase of power plant construction. The report will interface with two other reports that pertain to existing plants and describe what can be done from a retrofitting or work practices change perspective.

2006-12-07T23:59:59.000Z

248

Waste Feed Delivery System Phase 1 Preliminary Reliability and Availability and Maintainability Analysis [SEC 1 and 2  

SciTech Connect

The document presents updated results of the preliminary reliability, availability, maintainability analysis performed for delivery of waste feed from tanks 241-AZ-101 and 241-AN-105 to British Nuclear Fuels Limited, inc. under the Tank Waste Remediation System Privatization Contract. The operational schedule delay risk is estimated and contributing factors are discussed.

CARLSON, A.B.

1999-11-11T23:59:59.000Z

249

Load requirements for maintaining structural integrity of Hanford single-shell tanks during waste feed delivery and retrieval activities  

Science Conference Proceedings (OSTI)

This document provides structural load requirements and their basis for maintaining the structural integrity of the Hanford Single-Shell Tanks during waste feed delivery and retrieval activities. The requirements are based on a review of previous requirements and their basis documents as well as load histories with particular emphasis on the proposed lead transfer feed tanks for the privatized vitrification plant.

JULYK, L.J.

1999-09-22T23:59:59.000Z

250

CX-007999: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9: Categorical Exclusion Determination CX-007999: Categorical Exclusion Determination Wood Pole Replacement Along the Minidoka Power House-Unity 1 and Unity-Heyburn 1,...

251

Solar-powered turbocompressor heat pump system  

DOE Patents (OSTI)

The turbocompressor comprises a power turbine and a compressor turbine having respective rotors and on a common shaft, rotatably supported by bearings. A first working fluid is supplied by a power loop and is expanded in the turbine. A second working fluid is compressed in the turbine and is circulated in a heat pump loop. A lubricant is mixed with the second working fluid but is excluded from the first working fluid. The bearings are cooled and lubricated by a system which circulates the second working fluid and the intermixed lubricant through the bearings. Such system includes a pump, a thermostatic expansion valve for expanding the working fluid into the space between the bearings, and a return conduit system for withdrawing the expanded working fluid after it passes through the bearings and for returning the working fluid to the evaporator. A shaft seal excludes the lubricant from the power turbine. The power loop includes a float operable by liquid working fluid in the condenser for controlling a recirculation valve so as to maintain a minimum liquid level in the condenser, while causing a feed pump to pump most of the working fluid into the vapor generator. The heat pump compressor loop includes a float in the condenser for operating and expansion valve to maintain a minimum liquid working fluid level in the condenser while causing most of the working fluid to be expanded into the evaporator.

Landerman, A.M.; Biancardi, F.R.; Melikian, G.; Meader, M.D.; Kepler, C.E.; Anderson, T.J.; Sitler, J.W.

1982-08-12T23:59:59.000Z

252

Cost of Providing Ancillary Services from Power Plants  

Science Conference Proceedings (OSTI)

In a deregulated power supply market, extra generating capacity is needed to follow the moment-to-moment load variations in order to maintain the scheduled system frequency. This report describes a new methodology for determining the cost of providing regulation and frequency response service as an ancillary service.

1997-06-26T23:59:59.000Z

253

Sustainable Power Generation in Microbial Fuel Cells Using  

E-Print Network (OSTI)

Sustainable Power Generation in Microbial Fuel Cells Using Bicarbonate Buffer and Proton Transfer) isolation and selection of electricity- generating bacteria (3­5), (ii) selection and modification studies (11­21) to maintain a suitable pH for electricity- generating bacteria and/or to increase

Tullos, Desiree

254

Power-Pro: Programmable Power Management Architecture  

E-Print Network (OSTI)

This paper presents Power-Pro architecture (Programmable Power Management Architecture), a novel processor architecture for power reduction. Power-Pro architecture has following two functionalities, (i) Supply voltage and clock frequency can be dynamically varied, (ii) Active data-path width can be dynamically adjusted to requirement of application programs. For the application programs which require less performance or less data-path width, Power-Pro architecture realize dramatic power reduction. I. Introduction With recent popularizations in portable, batterypowered devices such as digital cellular telephones and personal digital assistants, minimizing power consumption of VLSI circuits becomes more important. As the system level power reduction techniques, the choice of optimal supply voltage(V DD ) and optimal active data-path width have strong impacts. In this paper we propose novel processor architecture Power-Pro [2] which can vary VDD and active data-path width of processor ...

Tohru Ishihara; Hiroto Yasuura; Programmable Power Management

1998-01-01T23:59:59.000Z

255

High power linear pulsed beam annealer  

DOE Patents (OSTI)

A high power pulsed electron beam is produced in a system comprised of an electron gun having a heated cathode, control grid, focus ring, and a curved drift tube. The drift tube is maintained at a high positive voltage with respect to the cathode to accelerate electrons passing through the focus ring and to thereby eliminate space charge. A coil surrounding the curved drift tube provides a magnetic field which maintains the electron beam focused about the axis of the tube and imparts motion on electrons in a spiral path for shallow penetration of the electrons into a target. The curvature of the tube is selected so there is no line of sight between the cathode and a target holder positioned within a second drift tube spaced coaxially from the curved tube. The second tube and the target holder are maintained at a reference voltage that decelerates the electrons. A second coil surrounding the second drift tube maintains the electron beam focused about the axis of the second drift tube and compresses the electron beam to the area of the target. The target holder can be adjusted to position the target where the cross section of the beam matches the area of the target.

Strathman, Michael D. (Concord, CA); Sadana, Devendra K. (Berkeley, CA); True, Richard B. (Sunnyvale, CA)

1983-01-01T23:59:59.000Z

256

Survivable pulse power space radiator  

DOE Patents (OSTI)

A thermal radiator system is described for use on an outer space vehicle, which must survive a long period of nonuse and then radiate large amounts of heat for a limited period of time. The radiator includes groups of radiator panels that are pivotally connected in tandem, so that they can be moved to deployed configuration wherein the panels lie largely coplanar, and to a stowed configuration wherein the panels lie in a stack to resist micrometerorite damage. The panels are mounted on a boom which separates a hot power source from a payload. While the panels are stowed, warm fluid passes through their arteries to keep them warm enough to maintain the coolant in a liquid state and avoid embrittlement of material. The panels can be stored in a largely cylindrical shell, with panels progressively further from the boom being of progressively shorter length. 5 figs.

Mims, J.; Buden, D.; Williams, K.

1988-03-11T23:59:59.000Z

257

Power conversion apparatus and method  

DOE Patents (OSTI)

A power conversion apparatus includes an interfacing circuit that enables a current source inverter to operate from a voltage energy storage device (voltage source), such as a battery, ultracapacitor or fuel cell. The interfacing circuit, also referred to as a voltage-to-current converter, transforms the voltage source into a current source that feeds a DC current to a current source inverter. The voltage-to-current converter also provides means for controlling and maintaining a constant DC bus current that supplies the current source inverter. The voltage-to-current converter also enables the current source inverter to charge the voltage energy storage device, such as during dynamic braking of a hybrid electric vehicle, without the need of reversing the direction of the DC bus current.

Su, Gui-Jia (Knoxville, TN)

2012-02-07T23:59:59.000Z

258

Electric power 2007  

SciTech Connect

Subjects covered include: power industry trends - near term fuel strategies - price/quality/delivery/opportunity; generating fleet optimization and plant optimization; power plant safety and security; coal power plants - upgrades and new capacity; IGCC, advanced combustion and CO{sub 2} capture technologies; gas turbine and combined cycle power plants; nuclear power; renewable power; plant operations and maintenance; power plant components - design and operation; environmental; regulatory issues, strategies and technologies; and advanced energy strategies and technologies. The presentations are in pdf format.

NONE

2007-07-01T23:59:59.000Z

259

Switching power pulse system  

DOE Patents (OSTI)

A switching system for delivering pulses of power from a source (10) to a load (20) using a storage capacitor (C3) charged through a rectifier (D1, D2), and maintained charged to a reference voltage level by a transistor switch (Q1) and voltage comparator (12). A thyristor (22) is triggered to discharge the storage capacitor through a saturable reactor (18) and fractional turn saturable transformer (16) having a secondary to primary turn ratio N of n:l/n=n.sup.2. The saturable reactor (18) functions as a "soaker" while the thyristor reaches saturation, and then switches to a low impedance state. The saturable transformer functions as a switching transformer with high impedance while a load coupling capacitor (C4) charges, and then switches to a low impedance state to dump the charge of the storage capacitor (C3) into the load through the coupling capacitor (C4). The transformer is comprised of a multilayer core (26) having two secondary windings (28, 30) tightly wound and connected in parallel to add their output voltage and reduce output inductance, and a number of single turn windings connected in parallel at nodes (32, 34) for the primary winding, each single turn winding linking a different one of the layers of the multilayer core. The load may be comprised of a resistive beampipe (40) for a linear particle accelerator and capacitance of a pulse forming network (42). To hold off discharge of the capacitance until it is fully charged, a saturable core (44) is provided around the resistive beampipe (40) to isolate the beampipe from the capacitance (42) until it is fully charged.

Aaland, Kristian (Livermore, CA)

1983-01-01T23:59:59.000Z

260

SOLAR POWER  

DOE Green Energy (OSTI)

Thermal energy storage (TES) is an integral part of a concentrated solar power (CSP) system. It enables plant operators to generate electricity beyond on sun hours and supply power to the grid to meet peak demand. Current CSP sensible heat storage systems employ molten salts as both the heat transfer fluid and the heat storage media. These systems have an upper operating temperature limit of around 400 C. Future TES systems are expected to operate at temperatures between 600 C to 1000 C for higher thermal efficiencies which should result in lower electricity cost. To meet future operating temperature and electricity cost requirements, a TES concept utilizing thermochemical cycles (TCs) based on multivalent solid oxides was proposed. The system employs a pair of reduction and oxidation (REDOX) reactions to store and release heat. In the storage step, hot air from the solar receiver is used to reduce the oxidation state of an oxide cation, e.g. Fe3+ to Fe2+. Heat energy is thus stored as chemical bonds and the oxide is charged. To discharge the stored energy, the reduced oxide is re-oxidized in air and heat is released. Air is used as both the heat transfer fluid and reactant and no storage of fluid is needed. This project investigated the engineering and economic feasibility of this proposed TES concept. The DOE storage cost and LCOE targets are $15/kWh and $0.09/kWh respectively. Sixteen pure oxide cycles were identified through thermodynamic calculations and literature information. Data showed the kinetics of re-oxidation of the various oxides to be a key barrier to implementing the proposed concept. A down selection was carried out based on operating temperature, materials costs and preliminary laboratory measurements. Cobalt oxide, manganese oxide and barium oxide were selected for developmental studies to improve their REDOX reaction kinetics. A novel approach utilizing mixed oxides to improve the REDOX kinetics of the selected oxides was proposed. It partially replaces some of the primary oxide cations with selected secondary cations. This causes a lattice charge imbalance and increases the anion vacancy density. Such vacancies enhance the ionic mass transport and lead to faster re-oxidation. Reoxidation fractions of Mn3O4 to Mn2O3 and CoO to Co3O4 were improved by up to 16 fold through the addition of a secondary oxide. However, no improvement was obtained in barium based mixed oxides. In addition to enhancing the short term re-oxidation kinetics, it was found that the use of mixed oxides also help to stabilize or even improve the TES properties after long term thermal cycling. Part of this improvement could be attributed to a reduced grain size in the mixed oxides. Based on the measurement results, manganese-iron, cobalt-aluminum and cobalt iron mixed oxides have been proposed for future engineering scale demonstration. Using the cobalt and manganese mixed oxides, we were able to demonstrate charge and discharge of the TES media in both a bench top fixed bed and a rotary kiln-moving bed reactor. Operations of the fixed bed configuration are straight forward but require a large mass flow rate and higher fluid temperature for charging. The rotary kiln makes direct solar irradiation possible and provides significantly better heat transfer, but designs to transport the TES oxide in and out of the reactor will need to be defined. The final reactor and system design will have to be based on the economics of the CSP plant. A materials compatibility study was also conducted and it identified Inconel 625 as a suitable high temperature engineering material to construct a reactor holding either cobalt or manganese mixed oxides. To assess the economics of such a CSP plant, a packed bed reactor model was established as a baseline. Measured cobalt-aluminum oxide reaction kinetics were applied to the model and the influences of bed properties and process parameters on the overall system design were investigated. The optimal TES system design was found to be a network of eight fixed bed reactors at 18.75 MWth each with charge and

PROJECT STAFF

2011-10-31T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

NREL: Concentrating Solar Power Research - Partnerships  

NLE Websites -- All DOE Office Websites (Extended Search)

Partnerships Partnerships NREL maintains partnerships to advance concentrating solar power research, development, and deployment efforts. Currently, NREL works with Sandia National Laboratories in Albuquerque, New Mexico, through SunLab-a partnership developed by the U.S. Department of Energy to administer its concentrating solar power R&D and analysis activities. SolarPACES Solar Power and Chemical Energy Systems (SolarPACES), an international program of the International Energy Agency, furthers collaborative development, testing, and marketing of CSP plants. NREL represents the U.S. activities and serves on various committees in SolarPACES, which now has 13 members: Algeria, Australia, Egypt, the European Commission, France, Germany, Israel, Mexico, South Africa, South Korea, Spain, Switzerland, and

262

Optical Isolation Transformer for Pulsed Power Applications  

DOE Green Energy (OSTI)

Described is a system that can provide electrical power to stacks of switching circuits while maintaining exceptional isolation between high voltage planes. High power laser diode bars are used to illuminate highly efficient photovoltaic cells. This is accomplished using efficient and cost-effective lens ducts and optical fiber segments. Such a system can be very efficient in transmitting optical power to the photocell. Using a glass lens duct we can achieve a theoretical isolation of 200 kV using a unit no bigger than a conventional dc-dc converter with isolation of only 50 kV. The trade off being total electrical efficiency, which is predicted to still be as high as 44 percent.

Matthew J. Heino

1999-08-01T23:59:59.000Z

263

STATUS OF THE NIF POWER CONDITIONING SYSTEM  

DOE Green Energy (OSTI)

The NIF Power Conditioning System provides the pulsed excitation required to drive flashlamps in the laser's optical amplifiers. Modular in design, each of the 192 Main Energy Storage Modules (MESMs) storage up to 2.2 MJ of electrical energy in its capacitor bank before delivering the energy to 20 pairs of flashlamps in a 400 {micro}s pulse (10% power points). The peak current of each MESM discharge is 0.5 MA. Production, installation, commissioning and operation of the NIF Power Conditioning continue to progress rapidly, with the goals of completing accelerated production in late 2007 and finishing commissioning by early 2008, all the while maintaining an aggressive operations schedule. To date, more than 80% of the required modules have been assembled, shipped and installed in the facility, representing more that 240 MJ of stored energy available for driving NIF flashlamps. The MESMs have displayed outstanding reliability during daily, multiple-shift operations.

Arnold, P; Hulsey, S; Ullery, G; Petersen, D; Pendleton, D; Ollis, C; Newton, M

2007-07-26T23:59:59.000Z

264

Northern Power Systems Inc | Open Energy Information  

Open Energy Info (EERE)

Northern Power Systems Inc Northern Power Systems Inc Place Waitsfield, Vermont Zip 5648 Sector Wind energy Product Vermont-based wind energy company that designs, builds, installs and maintains power generation systems. Coordinates 44.184296°, -72.838898° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":44.184296,"lon":-72.838898,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

265

Power Tower Systems for Concentrating Solar Power  

Energy.gov (U.S. Department of Energy (DOE))

In power tower concentrating solar power systems, numerous large, flat, sun-tracking mirrors, known as heliostats, focus sunlight onto a receiver at the top of a tall tower. A heat-transfer fluid...

266

DOE/EIS-0294; Sutter Power Project Final Environmental Impact Statement, Volume I (April 1999)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

COVER SHEET COVER SHEET Project Title: Sutter Power Project, Final Environmental Impact Statement Sutter County, California Federal Lead Agency: Western Area Power Administration, U.S. Department of Energy Related Actions: California Energy Commission's Certification for the Sutter Power Project Calpine Corporation's Application for Certification for the Sutter Power Project Sutter County General Plan Amendment and a Planned Development Rezone Western's Sutter Powerplant -- Interconnection Feasibility Study Technical Assistance: Foster Wheeler Environmental Corporation CH2M Hill R. W. Beck ABSTRACT Western Area Power Administration operates and maintains a high-voltage electric transmission system in California to deliver power to qualified customers. Calpine Corporation has requested that Western study

267

Resonant Power Conditioning and Compact Pulse Power ...  

Science Conference Proceedings (OSTI)

... (FEEDBACK) HV RECTIFIER AND FILTER NETWORK ... Los Alamos High Frequency Polyphase Resonant Power Conditioning ... 30 KW Loss ...

2012-10-31T23:59:59.000Z

268

Apparatus for adjusting and maintaining humidity of a gas at a constant value within a closed system  

SciTech Connect

An improved apparatus was developed for maintaining the humidity of a gas at a constant value within a closed system for long periods of time by using saturated salt solutions and isolating the sample environment from the salt environment. This apparatus avoids many problems associated with humidity/temperature chambers and off-the-shelf laboratory equipment, such as desiccators, that are being used for environmental studies under controlled conditions of humidity and temperature. 3 refs., 2 figs.

Walters, R.R.; Abernathy, B.

1986-02-03T23:59:59.000Z

269

Dynamic power management with hybrid power sources  

Science Conference Proceedings (OSTI)

DPM (Dynamic Power Management) is an effective technique for reducing the energy consumption of embedded systems that is based on migrating to a low power state when possible. While conventional DPM minimizes the energy consumption of the embedded system, ... Keywords: DPM, embedded system, fuel cell, hybrid power

Jianli Zhuo; Chaitali Chakrabarti; Kyungsoo Lee; Naehyuck Chang

2007-06-01T23:59:59.000Z

270

LIFE Power Plant Fusion Power Associates  

E-Print Network (OSTI)

LIFE Power Plant Fusion Power Associates December 14, 2011 Mike Dunne LLNL #12;NIf-1111-23714.ppt LIFE power plant 2 #12;LIFE delivery timescale NIf-1111-23714.ppt 3 #12;Timely delivery is enabled near-term, NIF based, NIC-derivative fusion performance § 3 allows small, thin Fresnel lenses ­ enables

271

Dynamic power management in environmentally powered systems  

Science Conference Proceedings (OSTI)

In this paper a framework for energy management in energy harvesting embedded systems is presented. As a possible example scenario, we focus on wireless sensor nodes which are powered by solar cells. We demonstrate that classical power management solutions ... Keywords: embedded systems, energy harvesting, model predictive control, power management, real-time scheduling, reward maximization

Clemens Moser; Jian-Jia Chen; Lothar Thiele

2010-01-01T23:59:59.000Z

272

Using SVM based method for equipment fault detection in a thermal power plant  

Science Conference Proceedings (OSTI)

Due to the growing demand on electricity, how to improve the efficiency of equipment in a thermal power plant has become one of the critical issues. Reports indicate that efficiency and availability are heavily dependant upon high reliability and maintainability. ... Keywords: Classification, Data mining, Maintenance, Support vector machines, Thermal power

Kai-Ying Chen; Long-Sheng Chen; Mu-Chen Chen; Chia-Lung Lee

2011-01-01T23:59:59.000Z

273

Modeling and simulation of new configuration of dynamic voltage restorer for power quality improvement  

Science Conference Proceedings (OSTI)

The dynamic voltage restorer (DVR) is a custom device that is used to maintain the voltage at the load terminals from various power quality problems from a disturbed incoming supply. In this paper, a novel control strategy is described for mitigation ... Keywords: custom device, dynamic voltage restorer (DVR), power quality, sags, sensitive loads, swells

Rosli Omar; Nasrudin Abdul Rahim

2011-04-01T23:59:59.000Z

274

Area and power-efficient innovative congestion-aware Network-on-Chip architecture  

Science Conference Proceedings (OSTI)

This paper proposes a novel Network-on-Chip architecture that not only enhances network transmission performance while maintaining a feasible implementation cost, but also provides a power-efficient solution for interconnection network scenarios. Diagonally-linked ... Keywords: Area-efficient, Congestion-aware, Interconnection network, Network-on-Chip (NoC), Power-efficient

Chifeng Wang; Wen-Hsiang Hu; Seung Eun Lee; Nader Bagherzadeh

2011-01-01T23:59:59.000Z

275

Real-time prediction of battery power requirements for electric vehicles  

Science Conference Proceedings (OSTI)

A battery management system (BMS) is responsible for protecting the battery from damage, predicting battery life, and maintaining the battery in an operational condition. In this paper, we propose an efficient way of predicting the power requirements ... Keywords: acceleration prediction, battery management system (BMS), electric vehicles (EVs), prediction of battery power requirement

Eugene Kim, Jinkyu Lee, Kang G. Shin

2013-04-01T23:59:59.000Z

276

Qualification of safety-critical systems in TVO nuclear power plants  

Science Conference Proceedings (OSTI)

Teollisuuden Voima Oy (TVO) operates two nuclear power plant units in Finland and has started to build a third one. The current nuclear power units have to continuously maintain and update existing instrumentation and control systems (I&C). Each new ... Keywords: FMECA, SPICE, instrumentation and control, qualification, safety-critical systems

Juha Halminen; Risto Nevalainen

2007-11-01T23:59:59.000Z

277

A single dimensionless variable for solar chimney power plant modeling  

Science Conference Proceedings (OSTI)

The solar chimney power plant is a relatively new technology for generating electricity from solar energy. In this paper dimensional analysis is used together with engineering intuition to combine eight primitive variables into only one dimensionless variable that establishes a dynamic similarity between a prototype and its scaled models. Three physical configurations of the plant were numerically tested for similarity: fully geometrically similar, partially geometrically similar, and dissimilar types. The values of the proposed dimensionless variable for all these cases were found to be nominally equal to unity. The value for the physical plant actually built and tested previously was also evaluated and found to be about the same as that of the numerical simulations, suggesting the validity of the proposition. The physical meaning of this dimensionless (similarity) variable is also interpreted; and the connection between the Richardson number and this new variable was found. It was found also that, for a fixed solar heat flux, different-sized models that are fully or partially geometrically similar share an equal excess temperature across the roof outlet. (author)

Koonsrisuk, Atit; Chitsomboon, Tawit [School of Mechanical Engineering, Institute of Engineering, Suranaree University of Technology, Muang District, Nakhon Ratchasima 30000 (Thailand)

2009-12-15T23:59:59.000Z

278

On-Site Renewable Power Purchase Agreements | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Project Funding » On-Site Renewable Power Purchase Agreements Project Funding » On-Site Renewable Power Purchase Agreements On-Site Renewable Power Purchase Agreements October 7, 2013 - 3:35pm Addthis On-site renewable power purchase agreements (PPAs) allow Federal agencies to fund on-site renewable energy projects with no up-front capital costs incurred. With a PPA, a developer installs a renewable energy system on agency property under an agreement that the agency will purchase the power generated by the system. The agency pays for the system through these power payments over the life of the contract. After installation, the developer owns, operates, and maintains the system for the life of the contract. For more information, read the Federal Energy Mangement Program's (FEMP) introductory guide to PPAs and sample documents.

279

NREL: Concentrating Solar Power Research - Data and Resources  

NLE Websites -- All DOE Office Websites (Extended Search)

Data and Resources Data and Resources For concentrating solar power technologies, NREL features the following online solar radiation resource data and solar resource maps, as well as data for renewable energy power plants. Also see TroughNet's data and resources specifically for parabolic trough technology. Concentrating Solar Power Projects around the World NREL, in conjunction with SolarPACES (Solar Power and Chemical Energy Systems), maintains a database of CSP projects around the world with plants that are either operational, under construction, or under development. CSP technologies include parabolic trough, linear Fresnel reflector, power tower, and dish/engine systems. Each project profile includes background information, a listing of project participants, and data on the power-plant

280

Power and energy  

Science Conference Proceedings (OSTI)

The author examines the development of nuclear power throughout the world, commencing with proposals for California, USA. Evidence that nuclear power remains viable in Asia include Japan Atomic Power Co.'s announcement of plans for a 1300 MW reactor ...

G. Zorpette

1995-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Solar powered desalination system  

E-Print Network (OSTI)

photon capture area and electrical power consumption. Bothcapture area (m 2 ) Electrical power consumption (kWh/kg HType 2 Type 3 Type 4 Electrical power consumption for these

Mateo, Tiffany Alisa

2011-01-01T23:59:59.000Z

282

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

power module - High temperature operation - Size reduction - 3-kW 120V single-phase inverter (250 C+) Input Power Output Power > 90% efficiency (estimated) Phase I: Very High...

283

Green Power Network: Green Power Markets Overview  

NLE Websites -- All DOE Office Websites (Extended Search)

Green Markets Green Markets Search Search Help More Search Options Search Site Map News TVA Seeks 126 MW of Renewables in 2014 December 2013 More News More News Subscribe to E-Mail Update Subscribe to e-mail update Events EPA Webinar - The Power of Aggregated Purchasing: How to Green Your Electricity Supply & Save Money January 15, 2014 1:00-2:00 p.m. ET Previous Webinars More News Features Green Power Market Status Report (2011 Data) Featured Green Power Reports Green Pricing Green Power Marketing Green Certificates Carbon Offsets State Policies Overview The essence of green power marketing is to provide market-based choices for electricity consumers to purchase power from environmentally preferred sources. The term "green power" is used to define power generated from renewable energy sources, such as wind and solar power, geothermal, hydropower and various forms of biomass. Green power marketing has the potential to expand domestic markets for renewable energy technologies by fostering greater availability of renewable electric service options in retail markets. Although renewable energy development has traditionally been limited by cost considerations, customer choice allows consumer preferences for cleaner energy sources to be reflected in market transactions. In survey after survey, customers have expressed a preference and willingness to pay more, if necessary, for cleaner energy sources. You can find more information about purchase options on our "Buying Green Power" page.

284

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

302011 Essential PV power plant features Reliable power conversion Extensive service network Remote monitoring & diagnostics Plant level control Advanced grid-friendly features...

285

Siemens Power Generation, Inc.  

NLE Websites -- All DOE Office Websites (Extended Search)

Presented at the 2005 Pittsburgh Coal Conference Siemens Power Generation, Inc. Page 1 of 10 Siemens Power Generation, Inc., All Rights Reserved Development of a Catalytic...

286

Laser Radiometry: Powering Up  

Science Conference Proceedings (OSTI)

... Radiometry: Powering Up. June 11, 2012. ... Contact: Marla Dowell 303-497- 7455. Chris Cromer examines one of PML's next-generation power meters ...

2012-06-14T23:59:59.000Z

287

Sunrise II Power Plant  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sunrise Power Company, LLC (Sunrise), has planned the modification of an existing power plant project to increase its generation capacity by 265 megawatts by 2003. The initial...

288

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

FOIAPrivacy Act Submit a FOIA Request DOE FOIA Requester Service Center Electronic Reading Room FOIA Links Power Marketing Administrations' FOIA Links Bonneville Power...

289

Electrolytes for power sources  

DOE Patents (OSTI)

Electrolytes for power sources, particularly alkaline and acidic power sources, comprising benzene polysulfonic acids and benzene polyphosphonic acids or salts of such acids.

Doddapaneni, Narayan (Albuquerque, NM); Ingersoll, David (Albuquerque, NM)

1995-01-01T23:59:59.000Z

290

Electrolytes for power sources  

DOE Patents (OSTI)

Electrolytes are disclosed for power sources, particularly alkaline and acidic power sources, comprising benzene polysulfonic acids and benzene polyphosphonic acids or salts of such acids. 7 figures.

Doddapaneni, N.; Ingersoll, D.

1995-01-03T23:59:59.000Z

291

Radioisotope Power Generation  

NLE Websites -- All DOE Office Websites (Extended Search)

Radioisotope Power Generation Long lived power sources are needed for equipment that is too remote or inaccessible for replacement. By choosing a radioactive element with a long...

292

Electric Power Monthly  

U.S. Energy Information Administration (EIA)

Net Generation by Energy Source: Commercial Combined Heat and Power Sector . Table 1.5. Net Generation by Energy Source: Industrial Combined Heat and Power Sector .

293

Nuclear Fusion Power  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Nuclear fusion reactors, if they can be made to work, promise virtually unlimited power for the indefinite future. This is because the fuel, isotopes of hydrogen, are...

294

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

CT (USA), international presence in USA, Canada, Germany (Fraunhofer, IKTS) and South Korea (Posco) Delivering Direct FuelCell (DFC ) power plants for On-Site Power and...

295

Energy Storage & Power Electronics 2008 Peer Review - Power Electronic...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

& Power Electronics 2008 Peer Review - Power Electronics (PE) Systems Presentations Energy Storage & Power Electronics 2008 Peer Review - Power Electronics (PE) Systems...

296

Karnataka Power Corporation Limited and National Thermal Power...  

Open Energy Info (EERE)

Karnataka Power Corporation Limited and National Thermal Power Corporation JV Jump to: navigation, search Name Karnataka Power Corporation Limited and National Thermal Power...

297

Water-Power Development, Conservation of Hydroelectric Power...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Water-Power Development, Conservation of Hydroelectric Power Dams and Works (Virginia) Water-Power Development, Conservation of Hydroelectric Power Dams and Works (Virginia)...

298

Flex power perspectives of indirect power system control through...  

Open Energy Info (EERE)

power perspectives of indirect power system control through dynamic power price (Smart Grid Project) Jump to: navigation, search Project Name Flex power perspectives of indirect...

299

Clean Power for the Internet  

E-Print Network (OSTI)

Data centers have been increasingly large users of energy over the past 10 years. With the rapid increase in Internet use, these facilities continue to be built, stressing the local electricity grids with their immense energy needs, and typically with the backup support of diesel generators belching pollution into the sky. The extent of these impacts is unknown. The change in market dynamics in the year 2001 resulted in a slower growth rate in data centers, as it did with the rest of the Internet industry, but it opened up an opportunity for incorporating energy efficient technologies into the design of power delivery to these buildings. More energy-efficient design will ease pressure on the electric grid and also decrease pollution in these areas, many of which are already areas of pollution non-attainment. This paper discusses the air quality impact of data centers, their impact on the electric grid, and the possibility of using clean distributed energy resources (DER) to meet their power reliability and quantity needs. Current DER installation and its success in maintaining the needed reliability are reviewed. The environmental and economic impact of the use of DER in these buildings are also reviewed and ways to overcome the potential barriers to this technology are discussed.

Brown, E.; Elliott, R. N.; Shipley, A.

2002-04-01T23:59:59.000Z

300

Military power requirements and backup power considerations  

Science Conference Proceedings (OSTI)

All US Air Force (USAF) facilities have certain critical power requirements that must be met in order to carry out their mission successfully. Internal USAF studies have shown that the mission can degrade precipitously as the available power decreases below the mission critical level. Now, more than ever before, the military and private industry are finding that certain functions, such as automated data processing and automated process control, respond catastrophically to power reductions. Furthermore, increased reliance on electrical power means, in the case of the Air Force, that critical power requirements are anticipated to increase by half over the next 15 yr. For these reasons and others, the USAF is investigating several means of improving the availability of electric power under adverse conditions above that which can be provided by an off-base supplier. Among the approaches to this problem being pursued at this time are a program to improve all sorts of generator sets on a service-wide basis and the Multimegawatt Terrestrial Power (MTP) Program, which is pursuing the design and testing of a small dedicated nuclear power source to provide critical mission power. The purpose of this paper is to provide some insight into some of the issues associated with USAF power programs.

Botts, T.E.

1986-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Apparatus for adjusting and maintaining the humidity of gas at a constant value within a closed system  

DOE Patents (OSTI)

The humidity of a gas within a closed system is maintained at constant level by providing a saturated salt solution within a lower chamber in communication with an upper chamber conjointly defined by upper and lower container sections in sealing contact with each other to establish a closed container. A partition wall separates the salt solution from the test region in the upper chamber. A tube extending through the partition plate allows humidified gas to pass from the lower to the upper chamber. A glass wool plug or membranous material within the tube prevents migration of salt into the test region.

Abernathy, Bethel R. (Franklin, OH); Walters, Ronald R. (Germantown, OH)

1986-01-01T23:59:59.000Z

302

Apparatus for adjusting and maintaining the humidity of gas at a constant value within a closed system  

DOE Patents (OSTI)

The humidity of a gas within a closed system is maintained at constant level by providing a saturated salt solution within a lower chamber in communication with an upper chamber conjointly defined by upper and lower container sections in sealing contact with each other to establish a closed container. A partition wall separates the salt solution from the test region in the upper chamber. A tube extending through the partition plate allows humidified gas to pass from the lower to the upper chamber. A glass wool plug or membranous material within the tube prevents migration of salt into the test region.

Abernathy, B.R.; Walters, R.R.

1985-08-05T23:59:59.000Z

303

Superconducting Power Equipment  

Science Conference Proceedings (OSTI)

The 2010 Electric Power Research Institute (EPRI) Technology Watch (Techwatch) report on superconducting power applications (EPRI report 1019995, Superconducting Power Equipment: Technology Watch 2010) introduced coverage about superconducting magnetic energy storage systems and superconducting transformers. The 2011 report contains additional information about superconducting power equipment, including progress to demonstrations in some projects. The 2011 report also includes a section on superconductin...

2011-12-22T23:59:59.000Z

304

Power Purchase Agreements  

Energy.gov (U.S. Department of Energy (DOE))

Presentation covers the power purchase agreements taken from the FEMP Alternative Finance Options (AFO) webinar.

305

Transportation and Stationary Power  

E-Print Network (OSTI)

heat, hydrogen and power (CHHP) "trigeneration" systems can hypothetically be configured to provide (1

306

STEWARDSHIP MAINTAINING NATURAL RICHES  

E-Print Network (OSTI)

SHOWCASING INNOVATION WATER CONSERVING PRESCIOUS RESOURCES ENERGY MOVING TO A BRIGHTER FUTURE WASTE REDUCING ENERGY MOVING TO A BRIGHTER FUTURE WASTE REDUCING AND RECYCLING #12;Sustainable Stanford Program SHOWCASING INNOVATION WATER CONSERVING PRESCIOUS RESOURCES ENERGY MOVING TO A BRIGHTER FUTURE WASTE REDUCING

Ford, James

307

Wind Power Impacts on Electric Power System Operating Costs: Summary and Perspective on Work to Date; Preprint  

DOE Green Energy (OSTI)

Electric utility system planners and operators are concerned that variations in wind plant output may increase the operating costs of the system. This concern arises because the system must maintain an instantaneous balance between the aggregate demand for electric power and the total power generated by all power plants feeding the system. This is a highly sophisticated task that utility operators and automatic controls perform routinely, based on well-known operating characteristics for conventional power plants and a great deal of experience accumulated over many years. System operators are concerned that variations in wind plant output will force the conventional power plants to provide compensating variations to maintain system balance, thus causing the conventional power plants to deviate from operating points chosen to minimize the total cost of operating the system. The operators' concerns are compounded by the fact that conventional power plants are generally under their control and thus are dispatchable, whereas wind plants are controlled instead by nature. Although these are valid concerns, the key issue is not whether a system with a significant amount of wind capacity can be operated reliably, but rather to what extent the system operating costs are increased by the variability of the wind.

Smith, J. C.; DeMeo, E. A.; Parsons, B.; Milligan, M.

2004-03-01T23:59:59.000Z

308

Green Power Network: Green Power Leadership Awards  

NLE Websites -- All DOE Office Websites (Extended Search)

Awards will highlight the accomplishments of green power suppliers (utilities, retail suppliers, REC marketers, and renewable energy project developers) that are innovators and...

309

The Importance of Establishing and Maintaining Continuity of Knowledge during 21st Century Nuclear Fuel Cycle Activities  

SciTech Connect

During this century, the entire nuclear fuel cycle will expand and become increasingly more global, taxing both the resources and capabilities of the International Atomic Energy Agency (IAEA) to maintain an effective Continuity of Knowledge (CoK) and its ability to provide timely detection of diversion. Uranium that currently is mined and milled in one country will be converted, enriched, and fabricated into fuel for reactors in an expanding set of new countries. This expansion will make it harder to guarantee that regional activities stay regional and that diversion detection is timely unless new and sustainable tools are developed to improve inspector effectiveness. To deal with this emerging reality, the IAEA must increase its use of unattended monitoring and employ new tools and methods that enhance CoK during all phases of the fuel cycle. This approach will help provide useful information to aid in detecting undeclared activities and create opportunities for timely and appropriate responses to events well before they enter phases of greater concern (e.g., enrichment). The systems that maintain CoK of safeguarded assets rely on containment and surveillance (C/S) technologies. The 21st century fuel cycle will require increased use of these technologies and systems, plus greater implementation of unattended systems that can securely collect data when inspectors are not present.

Pickett, Chris A [ORNL; Rowe, Nathan C [ORNL; Younkin, James R [ORNL; Wishard, Bernard [International Atomic Energy Agency (IAEA); Bean, Robert [U.S. Department of Energy, NNSA; Blair, Dianna [Sandia National Laboratories (SNL); Lawson, Ray [Savannah River National Laboratory (SRNL); Weeks, George [Savannah River National Laboratory (SRNL); Tolk, Keith [Milagro Consulting

2012-01-01T23:59:59.000Z

310

Improving Building Comfort and Energy Savings of the McKenzie Airport Terminal by Maintaining and Improving Pneumatic Control Systems  

E-Print Network (OSTI)

McKenzie Airport Terminal is located at Easterwood Airport, which is owned and operated by Texas A&M University. It was built in 1988. Most all HVAC equipment, which includes boiler, chiller, pumps, AHUs and exhaust fans, due to lack of maintenance, had some form of deteriorated controls, components, and operational function. For example, most of pneumatic controls were failed due to bad components, wrong settings, and disconnection before the Continuous CommissioningR (CCSM). This caused humid and hot problems of the building, and wasted energy. After maintaining and improving the pneumatic controls, the boiler and hot water pump is now turned off when outside air temperature is higher than 80F. The chiller is now shut off when the outside air temperature is below 55 F, and the economizers activate to maintain discharge air temperature when the outside air temperature is below 60 F. The building comfort in temperature and relative humidity (RH) is improved after CCSM. For example, average space temperature of the building was above 75 F most of the time before CCSM and is now 73 F after CCSM. The relative humidity in the baggage claim area was 70% before CCSM and is now 55% after CCSM. The annual savings of electricity for chiller and natural gas for boiler are $5,040 and $12,090 respectively. The total annual energy savings are $17,130.

Liu, C.; Bruner, H. L.; Deng, S.; Brundidge, T.; Turner, W. D.; Claridge, D. E.

2004-01-01T23:59:59.000Z

311

International Energy Outlook 2000 - Nuclear Power  

Gasoline and Diesel Fuel Update (EIA)

In the IEO2000 reference case, nuclear power represents a declining share of the world’s total electricity consumption from 1997 through 2020. Plant retirements are expected to produce net reductions in nuclear capacity in most of the industrialized nations. In the IEO2000 reference case, nuclear power represents a declining share of the world’s total electricity consumption from 1997 through 2020. Plant retirements are expected to produce net reductions in nuclear capacity in most of the industrialized nations. In 1998, a total of 2,291 billion kilowatthours of electricity was generated by nuclear power worldwide, providing 16 percent of the world’s total generation[1]. Among the countries with operating nuclear power plants, national dependence on nuclear energy for electricity varies greatly. Nine countries met at least 40 percent of total electricity demand with generation from nuclear reactors. Figure 68. Nuclear Shares of National Electricity Generation, 1998 [Sources] The prospects for nuclear power to maintain a significant share of

312

Keeping an eye on power system dynamics  

SciTech Connect

An interconnected power system is one of the largest and most complex of human achievements. It is maintained in a stable dynamic state only by tight control and protection, plus intelligent and diligent operation. Operating details are taken for granted by the general public; only when some catastrophic failure takes place is power system stability seen as newsworthy. Faults occur on power systems, most often through natural phenomena beyond human control. However, a well designed system will, for the most common faults, recover automatically and continue power delivery with very little inconvenience to its customers. This level of performance is achieved at a high cost in terms of manpower and equipment. In the future, the market economy is likely to force power systems much closer to their limits of stable operation, and operating decisions will have to be based on accurate, online system information and simulations rather than the current practice of extensive offline simulation of a comprehensive set of possible system operating conditions.

Hauer, J.; Johnson, J. [Pacific Northwest National Lab., Richland, WA (United States); Mittelstadt, B.; Litzenberger, W. [Bonneville Power Administration, Portland, OR (United States); Trudnowski, D.; Rogers, G.

1997-10-01T23:59:59.000Z

313

Murray City Power - Net Metering Pilot Program | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Murray City Power - Net Metering Pilot Program Murray City Power - Net Metering Pilot Program Murray City Power - Net Metering Pilot Program < Back Eligibility Commercial General Public/Consumer Residential Savings Category Solar Buying & Making Electricity Home Weatherization Water Wind Program Info State Utah Program Type Net Metering Provider Murray City Power Under a pilot program, Murray City Power offers net metering to customers that generate electricity using photovoltaic (PV), wind-electric or hydroelectric systems with a maximum capacity of 10 kilowatts (kW).* The utility will install and maintain a revenue meter capable of registering the bi-directional flow of electricity at the customer's facility. Any customer net excess generation (NEG) is carried over to the customer's next bill as a kilowatt-hour credit. Each April, any remaining NEG credits are

314

EIS-0447: Champlain Hudson Power Express Transmission Line Project, New  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7: Champlain Hudson Power Express Transmission Line Project, 7: Champlain Hudson Power Express Transmission Line Project, New York EIS-0447: Champlain Hudson Power Express Transmission Line Project, New York Summary This EIS evaluates the potential environmental impacts of a DOE proposal to grant a Presidential permit to Champlain Hudson Power Express, Inc., to construct, operate, maintain, and connect a new 1000-megawatt (MW) electric transmission system across the U.S.-Canada border in northeastern New York State. The proposed transmission line would run from the Canadian Province of Quebec to New York City. Public Comment Opportunities None available at this time. Documents Available for Download December 6, 2013 EIS-0447: DOE Notice of Availability of Draft Environmental Impact Statement Champlain Hudson Power Express Transmission Line Project, New York

315

Case Study - Florida Power & Light - Smart Grid Solutions Strengthen Reliability and Services - July 2012.pdf  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Florida Power & Light Florida Power & Light July 2012 1 Smart devices have been installed on 78 substation transformer banks. Smart Grid Solutions Strengthen Electric Reliability and Customer Services in Florida With 4.6 million customers, nearly 70,000 miles of power lines and 16 power plants, Florida Power and Light Company (FPL) is one of the nation's largest electric utilities. FPL says maintaining reliable service while keeping rates affordable is "Job One." While pursuing its mission, FPL is implementing "Energy Smart Florida," which is the largest and one of the most comprehensive of the U.S. Department of

316

High power fast ramping power supplies  

Science Conference Proceedings (OSTI)

Hundred megawatt level fast ramping power converters to drive proton and heavy ion machines are under research and development at accelerator facilities in the world. This is a leading edge technology. There are several topologies to achieve this power level. Their advantages and related issues will be discussed.

Marneris,I.; Bajon, E.; Bonati, R.; Sandberg, J.; Roser, T.; Tsoupas, N.

2009-05-04T23:59:59.000Z

317

Active Power Control from Wind Power (Presentation)  

DOE Green Energy (OSTI)

In order to keep the electricity grid stable and the lights on, the power system relies on certain responses from its generating fleet. This presentation evaluates the potential for wind turbines and wind power plants to provide these services and assist the grid during critical times.

Ela, E.; Brooks, D.

2011-04-01T23:59:59.000Z

318

Green Power Network: Green Power Policies  

NLE Websites -- All DOE Office Websites (Extended Search)

Green Power Marketing Green Certificates Carbon Offsets State Policies govern_purch Community Choice Aggregation Disclosure Policies Green Power Policies Net Metering Policies Green Power Policies A number of state and local governments have policies in place that encourage the development of green power markets. Government green power purchasing mandates or goals have been established by the federal government, as well as state and local governments to procure renewable energy for the electricity used by government facilities or operations. Community choice aggregation allows communities to determine their electricity generation sources by aggregating the community load and purchasing electricity from an alternate electricity supplier while still receiving transmission and distribution service from their existing provider.

319

Green Power Network: Community Choice Aggregation (CCA)  

NLE Websites -- All DOE Office Websites (Extended Search)

Community Choice Aggregation (CCA) Community Choice Aggregation (CCA) Community choice aggregation (CCA) is a state policy that enables local governments to aggregate electricity demand within their jurisdictions in order to procure alternative energy supplies while maintaining the existing electricity provider for transmission and distribution services. Many states passed CCA laws as part of electric restructuring legislation in the late 1990s and early 2000s. States that have passed CCA laws include California (2002), Illinois (2009), Massachusetts (1997), New Jersey (2003), Ohio (1999), and Rhode Island (1997). There are many reasons that a community may choose to develop a CCA, including the option to purchase more green power, reduce electricity cost, and provide power from more local sources.

320

Solar radiation powered battery reclaimer and charger  

SciTech Connect

A solar powered battery reclaiming and charging circuit is provided having a high frequency section (a bistable multi-vibrator, relaxation blocking bistable multi-vibrator or an oscillator inverter circuit) which is solar powered and output coupled by a close coupled RF transformer to the battery connected output section. The transformer has a secondary winding producing a current-voltage full wave output sharply defined through a two diode rectifying circuit to a multi-frequency 10 KHz to 100 KHz pulse output. The sharp pulse outputs with RF content in the 2--10 megahertz frequency range have specific frequencies equal to natural resonant frequencies of the specific electrolytes used in respective batteries. These resulting high frequency RF output signals in each pulse envelope structure are capable of reclaiming, maintaining and charging batteries that possess a liquid electrolyte or jell electrolyte and are beneficial to dry cell batteries as well in extending battery life. 9 figs.

Gali, C.E.

1994-01-04T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Assessment Methods and Operating Tools for Grid Reliability: An Executive Report on the Transmission Program of EPRI's Power Deliver y Reliability Initiative  

Science Conference Proceedings (OSTI)

Maintaining a high level of power grid reliability is one of the most pressing issues facing the electric power industry today. This report summarizes the achievements and planned activities of the transmission portion of the industry-wide Power Delivery Reliability Initiative, which is developing new tools and methods for assessing and improving grid reliability.

2001-03-26T23:59:59.000Z

322

Applications of an electronic transformer in a power distribution system  

E-Print Network (OSTI)

In electrical power distribution and power electronic applications, a transformer is an indispensable component which performs many functions. At its operating frequency (60/50 Hz), it is one of the most bulky and expensive components. The concept of the electronic transformer introduced previously has shown considerable reduction in size, weight, and volume by operating at a higher frequency. In this dissertation, the concept of the electronic transformer is further extended to the auto-connected phase-shifting type to reduce harmonics generated by nonlinear loads. It is shown that with the addition of primary side and secondary side AC/AC converters achieves phase-shifting. With the addition of converters, magnetic components are operated at a higher frequency to yield a smaller size and weight. Two types of auto-connected electronic transformer configurations are explored. In the first configuration, the secondary converter is eliminated and the output is suitable for rectifier type loads such as adjustable speed drives. In the second configuration, the secondary converter is added to obtain a sinusoidal phase-shifted AC output voltage. This approach is applicable in general applications. With the proposed approaches, the th and 7th harmonic in utility line currents, generated by two sets of nonlinear loads, are subtracted within the electronic transformer, thereby reducing the total harmonic distortion (THD) of the line current. The analysis and simulation results are presented. In the second part of the dissertation, the electronic transformer concept is applied to a telecommunication power supply (-48 VDC) system. The proposed approach consists of a matrix converter to convert the low frequency three-phase input AC utility to a high frequency AC output without a DC-link. The output of the matrix converter is then processed via a high frequency isolation transformer to produce -48 VDC. Digital control of the system ensures that the output voltage is regulated and the input currents are of high quality, devoid of low frequency harmonics and at near unity input power factor under varying load conditions. Due to the absence of DC-link electrolytic capacitors, the power density of the proposed rectifier is shown to be higher. Analysis, design example and experimental results are presented from a three-phase 208 V, 1.5 kW laboratory prototype converter.

Ratanapanachote, Somnida

2004-08-01T23:59:59.000Z

323

Power system identification toolbox: Phase two progress  

Science Conference Proceedings (OSTI)

This report describes current progress on a project funded by the Bonneville Power Administration (BPA) to develop a set of state-of-the-art analysis software (termed the Power System Identification [PSI] Toolbox) for fitting dynamic models to measured data. The project is being conducted as a three-phase effort. The first phase, completed in late 1992, involved investigating the characteristics of the analysis techniques by evaluating existing software and developing guidelines for best use. Phase Two includes extending current software, developing new analysis algorithms and software, and demonstrating and developing applications. The final phase will focus on reorganizing the software into a modular collection of documented computer programs and developing user manuals with instruction and application guidelines. Phase Two is approximately 50% complete; progress to date and a vision for the final product of the PSI Toolbox are described. The needs of the power industry for specialized system identification methods are particularly acute. The industry is currently pushing to operate transmission systems much closer to theoretical limits by using real-time, large-scale control systems to dictate power flows and maintain dynamic stability. Reliably maintaining stability requires extensive system-dynamic modeling and analysis capability, including measurement-based methods. To serve this need, the BPA has developed specialized system-identification computer codes through in-house efforts and university contract research over the last several years. To make full integrated use of the codes, as well as other techniques, the BPA has commissioned Pacific Northwest Laboratory (PNL) to further develop the codes and techniques into the PSI Toolbox.

Trudnowski, D.J.

1994-08-01T23:59:59.000Z

324

DOE-STD-1063-97; DOE Standard Establishing and Maintaining a Facility Representative Program at DOE Facilities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3-97 3-97 October 1997 Supersedes DOE-STD-1063-93 DOE STANDARD ESTABLISHING AND MAINTAINING A FACILITY REPRESENTATIVE PROGRAM AT DOE FACILITIES U.S. Department of Energy AREA FACR Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced directly from the best available copy. Available to DOE and DOE contractors from the Office of Scientific and Technical Information, P.O. Box 62, Oak Ridge, TN 37831; (423) 576-8401. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 487-4650. Order No. DE98001286 DOE-STD-1063-97 iii FOREWORD 1. This Department of Energy standard is approved for use by all DOE Components.

325

Power Management Controls  

NLE Websites -- All DOE Office Websites (Extended Search)

additional savings of 1.3 billion are lost because power management is present, but disabled. In some cases, power management is not compatible with the application or doesn't...

326

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

resolved Power capture and conversion in line with prediction 11 CF16539GG 1 OCEAN POWER DELIVERY LTD PROJECTS 12 CF16539GG 1 Enersis - Project 1 Enersis Portugal's largest...

327

Power and energy  

Science Conference Proceedings (OSTI)

The design and manufacture of electric power equipment, the one electrotechnology in which Europe could gain worldwide dominance by the end of the century, is examined. All three power-equipment categories-generation, transmission, and distribution-are ...

G. Zorpette

1990-04-01T23:59:59.000Z

328

IBM POWER6 microarchitecture  

Science Conference Proceedings (OSTI)

This paper describes the implementation of the IBM POWER6 microprocessor, a two-way simultaneous multithreaded (SMT) dual-core chip whose key features include binary compatibility with IBM POWER5 microprocessor-based systems; increased ...

H. Q. Le; W. J. Starke; J. S. Fields; F. P. O'Connell; D. Q. Nguyen; B. J. Ronchetti; W. M. Sauer; E. M. Schwarz; M. T. Vaden

2007-11-01T23:59:59.000Z

329

2025 Power Marketing Initiative  

NLE Websites -- All DOE Office Websites (Extended Search)

and is in the process of developing a plan for marketing and allocating LAP hydroelectric power after the FES contracts expire. We call this plan our 2025 Power Marketing...

330

Space Solar Power Program  

DOE Green Energy (OSTI)

Information pertaining to the Space Solar Power Program is presented on energy analysis; markets; overall development plan; organizational plan; environmental and safety issues; power systems; space transportation; space manufacturing, construction, operations; design examples; and finance.

Arif, H.; Barbosa, H.; Bardet, C.; Baroud, M.; Behar, A.; Berrier, K.; Berthe, P.; Bertrand, R.; Bibyk, I.; Bisson, J.; Bloch, L.; Bobadilla, G.; Bourque, D.; Bush, L.; Carandang, R.; Chiku, T.; Crosby, N.; De Seixas, M.; De Vries, J.; Doll, S.; Dufour, F.; Eckart, P.; Fahey, M.; Fenot, F.; Foeckersperger, S.; Fontaine, J.E.; Fowler, R.; Frey, H.; Fujio, H.; Gasa, J.M.; Gleave, J.; Godoe, J.; Green, I.; Haeberli, R.; Hanada, T.; Ha

1992-08-01T23:59:59.000Z

331

Body powered thermoelectric systems  

E-Print Network (OSTI)

Great interest exists for and progress has be made in the effective utilization of the human body as a possible power supply in hopes of powering such applications as sensors and continuously monitoring medical devices ...

Settaluri, Krishna Tej

2012-01-01T23:59:59.000Z

332

Data Center Power Consumption  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Center Power Consumption Center Power Consumption A new look at a growing problem Fact - Data center power density up 10x in the last 10 years 2.1 kW/rack (1992); 14 kW/rack (2007) Racks are not fully populated due to power/cooling constraints Fact - Increasing processor power Moore's law Fact - Energy cost going up 3 yr. energy cost equivalent to acquisition cost Fact - Iterative power life cycle Takes as much energy to cool computers as it takes to power them. Fact - Over-provisioning Most data centers are over-provisioned with cooling and still have hot spots November 2007 SubZero Engineering An Industry at the Crossroads Conflict between scaling IT demands and energy efficiency Server Efficiency is improving year after year Performance/Watt doubles every 2 years Power Density is Going Up

333

Concentrating Solar Power  

DOE Green Energy (OSTI)

Summarizes the goals and activities of the DOE Solar Energy Technologies Program efforts within its concentrating solar power subprogram.

Not Available

2008-09-01T23:59:59.000Z

334

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

disconnect switches, microprocessor relays, power transformers, surge arresters, and transformer bushings information resources management equipment and supplies such as monitors,...

335

Power Conversion System Architectures  

Science Conference Proceedings (OSTI)

... of Transformers Vacuum Pressure Impregnated (VPI) Oil Immersed Cast Coil Transformer Configurations Single winding 5/24/2012 Power ...

2012-11-13T23:59:59.000Z

336

Soldier power. Battery charging.  

E-Print Network (OSTI)

Soldier power. Marine. Battery charging. Advertising. Remote. SOFC (NanoDynamics, AMI) 60 watts q SOFC #12;

Hong, Deog Ki

337

Electric Power Metrology News  

Science Conference Proceedings (OSTI)

... Next-generation "smart" electrical meters for residential and commercial ... NIST Team Demystifies Utility of Power Factor Correction Devices Release ...

2010-05-24T23:59:59.000Z

338

Increased Power Flow Guidebook  

Science Conference Proceedings (OSTI)

The Increased Power Flow (IPF) Guidebook is a state-of-the-art and best practices guidebook on increasing power flow capacities of existing overhead transmission lines, underground cables, power transformers, and substation equipment without compromising safety and reliability. The Guidebook discusses power system concerns and limiting conditions to increasing capacity, reviews available technology options and methods, illustrates alternatives with case studies, and analyzes costs and benefits of differe...

2005-11-16T23:59:59.000Z

339

Superconducting Power Cables  

Science Conference Proceedings (OSTI)

Power cables constructed from superconducting materials are being realized in utility demonstrations within the United States. Cooled by liquid nitrogen, high temperature superconducting power cables can transfer large amounts of power through relatively small cross sections. The key to their high power capacity is the high current density inherent with superconductors; a superconducting wire can conduct several times as much current as copper or aluminum conductors of the same cross section. For the pas...

2006-11-30T23:59:59.000Z

340

Wind powering America: Colorado  

DOE Green Energy (OSTI)

This fact sheet contains information about green power programs in Colorado and a description of the Ponnequin Wind Farm.

O'Dell, K.

2000-04-03T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Search for fusion power  

SciTech Connect

A brief review of the basics of fusion power is given. Both inertial confinement and magnetic confinement fusion are discussed.

Post, R.F.

1978-10-12T23:59:59.000Z

342

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Efficiency Program Energy Efficiency Program Administration Administration Charles Goldman E. O. Lawrence Berkeley National Laboratory CAGoldman@lbl.gov Colorado DSM Informational Workshop Colorado Public Utilities Commission February 8, 2007 Overview of Talk Overview of Talk * Key functions in administering and delivering EE * Summary of State experience with alternative approaches to administering energy efficiency * Pros and cons of alternative approaches * What does it take to administer and deliver What does it take to administer and deliver Energy Efficiency programs? Energy Efficiency programs? * General Administration and Coordination - Propose & manage budget for portfolio of programs; maintain contracts with primary contractors; maintain IT system for reports to PUC,

343

Power Plant Cycling Costs  

Science Conference Proceedings (OSTI)

This report provides a detailed review of the most up to date data available on power plant cycling costs. The primary objective of this report is to increase awareness of power plant cycling cost, the use of these costs in renewable integration studies and to stimulate debate between policymakers, system dispatchers, plant personnel and power utilities.

Kumar, N.; Besuner, P.; Lefton, S.; Agan, D.; Hilleman, D.

2012-07-01T23:59:59.000Z

344

INTEGRATED CONTROL OF NEXT GENERATION POWER SYSTEM  

Science Conference Proceedings (OSTI)

Control methodologies provide the necessary data acquisition, analysis and corrective actions needed to maintain the state of an electric power system within acceptable operating limits. These methods are primarily software-based algorithms that are nonfunctional unless properly integrated with system data and the appropriate control devices. Components of the control of power systems today include protective relays, supervisory control and data acquisition (SCADA), distribution automation (DA), feeder automation, software agents, sensors, control devices and communications. Necessary corrective actions are still accomplished using large electromechanical devices such as vacuum, oil and gas-insulated breakers, capacitor banks, regulators, transformer tap changers, reclosers, generators, and more recently FACTS (flexible AC transmission system) devices. The recent evolution of multi-agent system (MAS) technologies has been reviewed and effort made to integrate MAS into next generation power systems. A MAS can be defined as â??â?¦a loosely-coupled network of problem solvers that work together to solve problems that are beyond their individual capabilitiesâ?¦â?. These problem solvers, often called agents, are autonomous and may be heterogeneous in nature. This project has shown that a MAS has significant advantages over a single, monolithic, centralized problem solver for next generation power systems. Various communication media are being used in the electric power system today, including copper, optical fiber and power line carrier (PLC) as well as wireless technologies. These technologies have enabled the deployment of substation automation (SA) at many facilities. Recently, carrier and wireless technologies have been developed and demonstrated on a pilot basis. Hence, efforts have been made by this project to penetrate these communication technologies as an infrastructure for next generation power systems. This project has thus pursued efforts to use specific MAS methods as well as pertinent communications protocols to imbed and assess such technologies in a real electric power distribution system, specifically the Circuit of the Future (CoF) developed by Southern California Edison (SCE). By modeling the behavior and communication for the components of a MAS, the operation and control of the power distribution circuit have been enhanced. The use of MAS to model and integrate a power distribution circuit offers a significantly different approach to the design of next generation power systems. For example, ways to control a power distribution circuit that includes a micro-grid while considering the impacts of thermal constraints, and integrating voltage control and renewable energy sources on the main power system have been pursued. Both computer simulations and laboratory testbeds have been used to demonstrate such technologies in electric power distribution systems. An economic assessment of MAS in electric power systems was also performed during this project. A report on the economic feasibility of MAS for electric power systems was prepared, and particularly discusses the feasibility of incorporating MAS in transmission and distribution (T&D) systems. Also, the commercial viability of deploying MAS in T&D systems has been assessed by developing an initial case study using utility input to estimate the benefits of deploying MAS. In summary, the MAS approach, which had previously been investigated with good success by APERC for naval shipboard applications, has now been applied with promising results for enhancing an electric power distribution circuit, such as the Circuit of the Future developed by Southern California Edison. The results for next generation power systems include better ability to reconfigure circuits, improve protection and enhance reliability.

None

2010-02-28T23:59:59.000Z

345

Peak power identification on power bumps during test application  

Science Conference Proceedings (OSTI)

Peak power during test can seriously impact circuit performance as well as the power safety for both CUT and tester. In this paper, we propose a method of layout-aware weighted switching activity identification flow that evaluates peak current/power ... Keywords: CMOS device, peak power identification, power bumps, test application, layout-aware weighted switching activity identification flow, dynamic power model, parasitic capacitance, resistance network, power bus, power delivery path, IR-drop, commercial power sign-off analysis tool

Wei Zhao; M. Tehranipoor

2011-07-01T23:59:59.000Z

346

Study of the implementation of STATCOM on DFIG-based wind farm connected to a power system  

Science Conference Proceedings (OSTI)

The integration of Doubly Fed Induction Generator (DFIG) based wind farm into the power grid has become a major concern for power system engineers today. Voltage stability is a key factor to maintain DFIG-based wind farm in service during the grid disturbances. ...

Tarek Medalel Masaud; P. K. Sen

2012-01-01T23:59:59.000Z

347

Political Institutions, Competing Principals, and Party Unity in Legislative Voting  

E-Print Network (OSTI)

republic israel new zealand poland brazil peru united statesrepublic israel new zealand poland brazil peru united statesintra- party competition, Poland. WRICE is extraordinarily

Carey, John M.

2005-01-01T23:59:59.000Z

348

High-resolution magnetohydrodynamic equilibrium code for unity beta plasmas  

E-Print Network (OSTI)

vertical field limits the plasma beta for non elongatedbeta equilibrium numerical procedure High-? configurations have extreme Shafranov shifts, compressing the flux surfaces on the low field

Gourdain, P A

2006-01-01T23:59:59.000Z

349

Thermoelectrically Pumped Light-Emitting Diodes Operating above Unity Efficiency  

E-Print Network (OSTI)

A heated semiconductor light-emitting diode at low forward bias voltage V

Santhanam, Parthiban

350

Local control of reactive power by distributed photovoltaic generators  

SciTech Connect

High penetration levels of distributed photovoltaic (PV) generation on an electrical distribution circuit may severely degrade power quality due to voltage sags and swells caused by rapidly varying PV generation during cloud transients coupled with the slow response of existing utility compensation and regulation equipment. Although not permitted under current standards for interconnection of distributed generation, fast-reacting, VAR-capable PV inverters may provide the necessary reactive power injection or consumption to maintain voltage regulation under difficult transient conditions. As side benefit, the control of reactive power injection at each PV inverter provides an opportunity and a new tool for distribution utilities to optimize the performance of distribution circuits, e.g. by minimizing thermal losses. We suggest a local control scheme that dispatches reactive power from each PV inverter based on local instantaneous measurements of the real and reactive components of the consumed power and the real power generated by the PVs. Using one adjustable parameter per circuit, we balance the requirements on power quality and desire to minimize thermal losses. Numerical analysis of two exemplary systems, with comparable total PV generation albeit a different spatial distribution, show how to adjust the optimization parameter depending on the goal. Overall, this local scheme shows excellent performance; it's capable of guaranteeing acceptable power quality and achieving significant saving in thermal losses in various situations even when the renewable generation in excess of the circuit own load, i.e. feeding power back to the higher-level system.

Chertkov, Michael [Los Alamos National Laboratory; Turitsyn, Konstantin [Los Alamos National Laboratory; Sulc, Petr [Los Alamos National Laboratory; Backhaus, Scott [Los Alamos National Laboratory

2010-01-01T23:59:59.000Z

351

PUREX (SAMCONS) uninterruptible power supply (UPS) acceptance test procedure  

SciTech Connect

This Acceptance Test Procedure for the PUREX Surveillance and Monitoring and Control System (SAMCONS) Uninterruptible Power Supply (UPS) provides for testing and verifying the proper operation of the control panel alarms and trouble functions, the 6roper functioning of the AC inverter, ability of the battery supply to maintain the SAMCONS load for a minimum of two hours , and proper interaction with the SAMCONS Video graphic displays for alarm displays.

Blackaby, W.B.

1997-09-01T23:59:59.000Z

352

Soft Magnetic Materials for High Power and High Frequency Power ...  

Science Conference Proceedings (OSTI)

Symposium, Advanced Materials for Power Electronics, Power Conditioning, and ... are in high demand for the next generation of miniaturized power electronics.

353

Wind Powering America Webinar: Wind Power Economics: Past, Present...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Economics: Past, Present, and Future Trends Wind Powering America Webinar: Wind Power Economics: Past, Present, and Future Trends November 23, 2011 - 1:43pm Addthis Wind...

354

InPower Systems | Open Energy Information  

Open Energy Info (EERE)

InPower Systems InPower Systems Jump to: navigation, search Name InPower Systems Place Carbondale, Colorado Zip 81623 Sector Geothermal energy, Solar Product InPower Systems designs, installs and maintains turn-key solar, solar thermal, geothermal and energy smart systems in homes and businesses in Colorado. Coordinates 41.573959°, -75.501361° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.573959,"lon":-75.501361,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

355

Reactor power history from fission product signatures  

E-Print Network (OSTI)

The purpose of this research was to identify fission product signatures that could be used to uniquely identify a specific spent fuel assembly in order to improve international safeguards. This capability would help prevent and deter potential diversion of spent fuel for a nuclear weapons program. The power history experienced by a fuel assembly is distinct and could serve as the basis of a method for unique identification. Using fission product concentrations to characterize the assembly power history would limit the ability of a proliferator to deceive the identification method. As part of the work completed, the TransLat lattice physics code was successfully benchmarked for fuel depletion. By developing analytical models for potential monitor isotopes an understanding was built of how specific isotope characteristics affect the production and destruction mechanisms that determine fission product concentration. With this knowledge potential monitor isotopes were selected and tested for concentration differences as a result of power history variations. Signature ratios were found to have significant concentration differences as a result of power history variations while maintaining a constant final burnup. A conceptual method for implementation of a fission product identification system was proposed in conclusion.

Sweeney, David J.

2008-12-01T23:59:59.000Z

356

Electric Power Monthly  

Gasoline and Diesel Fuel Update (EIA)

Electric Power Monthly > Electric Power Monthly Back Issues Electric Power Monthly > Electric Power Monthly Back Issues Electric Power Monthly Back Issues Monthly Excel files zipped 2010 January February March April May June July August September October November December 2009 January February March April May June July August September October November December 2008 January February March March Supplement April May June July August September October November December 2007 January February March April May June July August September October November December 2006 January February March April May June July August September October November December 2005 January February March April May June July August September October November December

357

ADEPT: Efficient Power Conversion  

SciTech Connect

ADEPT Project: In todays increasingly electrified world, power conversionthe process of converting electricity between different currents, voltage levels, and frequenciesforms a vital link between the electronic devices we use every day and the sources of power required to run them. The 14 projects that make up ARPA-Es ADEPT Project, short for Agile Delivery of Electrical Power Technology, are paving the way for more energy efficient power conversion and advancing the basic building blocks of power conversion: circuits, transistors, inductors, transformers, and capacitors.

None

2011-01-01T23:59:59.000Z

358

Power factors revealed  

SciTech Connect

When it comes to power, not all electric appliances are equal. To find out how much power an appliance consumes, energy auditors occasionally multiply line voltage by the current reading obtained from a clamp-on ammeter. However, depending on the appliance, this simple calculation will not always reflect true power usages. Since utilities bill only for true energy usage, residential energy audits should reflect the true power usage. This article explains in detail measuring power usage, ending with a number of suggestions including use of a wattmeter rather than a ammeter. 2 figs.

Brule, P.

1997-05-01T23:59:59.000Z

359

Multimode power processor  

DOE Patents (OSTI)

In one embodiment, a power processor which operates in three modes: an inverter mode wherein power is delivered from a battery to an AC power grid or load; a battery charger mode wherein the battery is charged by a generator; and a parallel mode wherein the generator supplies power to the AC power grid or load in parallel with the battery. In the parallel mode, the system adapts to arbitrary non-linear loads. The power processor may operate on a per-phase basis wherein the load may be synthetically transferred from one phase to another by way of a bumpless transfer which causes no interruption of power to the load when transferring energy sources. Voltage transients and frequency transients delivered to the load when switching between the generator and battery sources are minimized, thereby providing an uninterruptible power supply. The power processor may be used as part of a hybrid electrical power source system which may contain, in one embodiment, a photovoltaic array, diesel engine, and battery power sources. 31 figs.

O' Sullivan, G.A.; O' Sullivan, J.A.

1999-07-27T23:59:59.000Z

360

Multimode power processor  

SciTech Connect

In one embodiment, a power processor which operates in three modes: an inverter mode wherein power is delivered from a battery to an AC power grid or load; a battery charger mode wherein the battery is charged by a generator; and a parallel mode wherein the generator supplies power to the AC power grid or load in parallel with the battery. In the parallel mode, the system adapts to arbitrary non-linear loads. The power processor may operate on a per-phase basis wherein the load may be synthetically transferred from one phase to another by way of a bumpless transfer which causes no interruption of power to the load when transferring energy sources. Voltage transients and frequency transients delivered to the load when switching between the generator and battery sources are minimized, thereby providing an uninterruptible power supply. The power processor may be used as part of a hybrid electrical power source system which may contain, in one embodiment, a photovoltaic array, diesel engine, and battery power sources.

O' Sullivan, George A. (Pottersville, NJ); O' Sullivan, Joseph A. (St. Louis, MO)

1999-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 Northern Power Systems, Inc 6 Northern Power Systems, Inc Northern Power Systems 182 Mad River Park Waitsfield, VT 05673 Ultracapacitor EnergyBridge(tm) UPS for Palmdale Water District DOE/ESS PEER Review November 3, 2006 11/03/2006 Northern Power Systems, Inc © 2006 2 Northern Power  Distributed Energy Systems Corp (NASDAQ:DESC)  Energy Solutions since 1974  Products, Systems and Services Divisions  Hundreds of Projects around the World  HQ and Manufacturing in Vermont  Regional offices in NY, TX, CA, England, and Mexico 11/03/2006 Northern Power Systems, Inc © 2006 3 Project Overview  CEC - California Energy Commission  Funding agency  Palmdale Water District  Award recipient, host site  Northern Power  Technology provider  Black & Veatch  Owner's engineer

362

Solar thermal power  

DOE Green Energy (OSTI)

Solar thermal power is produced by three types of concentrating systems, which utilize parabolic troughs, dishes, and heliostats as the solar concentrators. These systems are at various levels of development and commercialization in the United States and in Europe. The U.S. Industry is currently developing these systems for export at the end of this century and at the beginning of the next one for remote power, village electrification, and grid-connected power. U.S. utilities are not forecasting to need power generation capacity until the middle of the first decade of the 21{sup st} century. At that time, solar thermal electric power systems should be cost competitive with conventional power generation in some unique U.S. markets. In this paper, the authors describe the current status of the development of trough electric, dish/engine, and power tower solar generation systems. 46 refs., 20 figs., 8 tabs.

Mancini, T.R.; Kolb, G.J.; Prairie, M.R. [Sandia National Labs., Albuquerque, NM (United States)

1997-12-31T23:59:59.000Z

363

Tools, Methods, and Modeling for Dynamic Distribution Systems, Power Factor Guidelines: Power Control with Distributed Energy Resources  

Science Conference Proceedings (OSTI)

With the onset in the past few years of tax incentives, subsidies, and renewable portfolio standards for distributed energy resources (DER), utilities are experiencing increasing numbers of interconnection requests for both large, MW-class systems as well as small, residential-scale systems. As a result, utilities need methods for integrating DER without impacting system reliability or power quality for other customers, while also maintaining flexibility for future changes and minimizing ...

2013-12-19T23:59:59.000Z

364

Maintaining a Technology-Neutral Approach to Hydrogen Production Process Development through Conceptual Design of the Next Generation Nuclear Plant  

DOE Green Energy (OSTI)

The Next Generation Nuclear Plant (NGNP) project was authorized in the Energy Policy Act of 2005 (EPAct), tasking the U.S. Department of Energy (DOE) with demonstrating High Temperature Gas-Cooled Reactor (HTGR) technology. The demonstration is to include the technical, licensing, operational, and commercial viability of HTGR technology for the production of electricity and hydrogen. The Nuclear Hydrogen Initiative (NHI), a component of the DOE Hydrogen Program managed by the Office of Nuclear Energy, is also investigating multiple approaches to cost effective hydrogen production from nuclear energy. The objective of NHI is development of the technology and information basis for a future decision on commercial viability. The initiatives are clearly intertwined. While the objectives of NGNP and NHI are generally consistent, NGNP has progressed to the project definition phase and the project plan has matured. Multiple process applications for the NGNP require process heat, electricity and hydrogen in varied combinations and sizes. Coupling these processes to the reactor in multiple configurations adds complexity to the design, licensing and demonstration of both the reactor and the hydrogen production process. Commercial viability of hydrogen production may depend on the specific application and heat transport configuration. A component test facility (CTF) is planned by the NGNP to support testing and demonstration of NGNP systems, including those for hydrogen production, in multiple configurations. Engineering-scale demonstrations in the CTF are expected to start in 2012 to support scheduled design and licensing activities leading to subsequent construction and operation. Engineering-scale demonstrations planned by NHI are expected to start at least two years later. Reconciliation of these schedules is recommended to successfully complete both initiatives. Hence, closer and earlier integration of hydrogen process development and heat transport systems is sensible. For integration purposes, an analysis comparing the design, cost and schedule impact of maintaining a technology neutral approach through conceptual design or making an early hydrogen process technology selection was performed. Early selection does not specifically eliminate a technology, but rather selects the first hydrogen technology for demonstration. A systems-engineering approach was taken to define decision-making criteria for selecting a hydrogen technology. The relative technical, cost and schedule risks of each approach were analyzed and risk mitigation strategies were recommended, including provisions to maintain close collaboration with the NHI. The results of these analyses are presented here.

Michael W. Patterson

2008-05-01T23:59:59.000Z

365

ADVANCED MONITORING TO IMPROVE COMBUSTION TURBINE/COMBINED CYCLE CT/(CC) RELIABILITY, AVAILABILITY AND MAINTAINABILITY (RAM)  

Science Conference Proceedings (OSTI)

Power generators are concerned with the maintenance costs associated with the advanced turbines that they are purchasing. Since these machines do not have fully established operation and maintenance (O&M) track records, power generators face financial risk due to uncertain future maintenance costs. This risk is of particular concern, as the electricity industry transitions to a competitive business environment in which unexpected O&M costs cannot be passed through to consumers. These concerns have accelerated the need for intelligent software-based diagnostic systems that can monitor the health of a combustion turbine in real time and provide valuable information on the machine's performance to its owner/operators. EPRI, Impact Technologies, Boyce Engineering, and Progress Energy have teamed to develop a suite of intelligent software tools integrated with a diagnostic monitoring platform that will, in real time, interpret data to assess the ''total health'' of combustion turbines. The Combustion Turbine Health Management System (CTHM) will consist of a series of dynamic link library (DLL) programs residing on a diagnostic monitoring platform that accepts turbine health data from existing monitoring instrumentation. The CTHM system will be a significant improvement over currently available techniques for turbine monitoring and diagnostics. CTHM will interpret sensor and instrument outputs, correlate them to a machine's condition, provide interpretative analyses, project servicing intervals, and estimate remaining component life. In addition, it will enable real-time anomaly detection and diagnostics of performance and mechanical faults, enabling power producers to more accurately predict critical component remaining useful life and turbine degradation.

Leonard Angello

2004-03-31T23:59:59.000Z

366

ADVANCED MONITORING TO IMPROVE COMBUSTION TURBINE/COMBINED CYCLE CT/(CC) RELIABILITY, AVAILABILITY AND MAINTAINABILITY (RAM)  

Science Conference Proceedings (OSTI)

Power generators are concerned with the maintenance costs associated with the advanced turbines that they are purchasing. Since these machines do not have fully established operation and maintenance (O&M) track records, power generators face financial risk due to uncertain future maintenance costs. This risk is of particular concern, as the electricity industry transitions to a competitive business environment in which unexpected O&M costs cannot be passed through to consumers. These concerns have accelerated the need for intelligent software-based diagnostic systems that can monitor the health of a combustion turbine in real time and provide valuable information on the machine's performance to its owner/operators. EPRI, Impact Technologies, Boyce Engineering, and Progress Energy have teamed to develop a suite of intelligent software tools integrated with a diagnostic monitoring platform that will, in real time, interpret data to assess the ''total health'' of combustion turbines. The Combustion Turbine Health Management System (CTHM) will consist of a series of dynamic link library (DLL) programs residing on a diagnostic monitoring platform that accepts turbine health data from existing monitoring instrumentation. The CTHM system will be a significant improvement over currently available techniques for turbine monitoring and diagnostics. CTHM will interpret sensor and instrument outputs, correlate them to a machine's condition, provide interpretative analyses, project servicing intervals, and estimate remaining component life. In addition, it will enable real-time anomaly detection and diagnostics of performance and mechanical faults, enabling power producers to more accurately predict critical component remaining useful life and turbine degradation.

Leonard Angello

2004-09-30T23:59:59.000Z

367

EIS-0447: Champlain Hudson Power Express Transmission Line Project, New  

NLE Websites -- All DOE Office Websites (Extended Search)

447: Champlain Hudson Power Express Transmission Line Project, 447: Champlain Hudson Power Express Transmission Line Project, New York EIS-0447: Champlain Hudson Power Express Transmission Line Project, New York Summary This EIS evaluates the environmental impacts of a DOE proposal to grant a Presidential permit to Champlain Hudson Power Express, Inc., to construct, operate, maintain, and connect a new 1000-megawatt (MW) electric transmission system across the U.S.-Canada border in northeastern New York State. The proposed transmission line will run from the Canadian Province of Quebec to New York City. DOE also published a notice correcting the location of the public hearing that was held on November 19, 2013. Public Comment Opportunities As of December 6, 2013 - Comment Period Extended through 1/15/14 Written comments must be received by January 15, 2014. Comments submitted

368

Solar Power and the Electric Grid, Energy Analysis (Fact Sheet)  

NLE Websites -- All DOE Office Websites (Extended Search)

Power and the Electric Grid Power and the Electric Grid In today's electricity generation system, different resources make different contributions to the electricity grid. This fact sheet illustrates the roles of distributed and centralized renewable energy technologies, particularly solar power, and how they will contribute to the future electricity system. The advantages of a diversified mix of power generation systems are highlighted. Grid 101: How does the electric grid work? The electric grid-an interconnected system illustrated in Figure 1-maintains an instantaneous balance between supply and demand (generation and load) while moving electricity from generation source to customer. Because large amounts of electricity are difficult to store, the amount generated and fed into the system must be care-

369

Options for Control of Reactive Power by Distributed Photovoltaic Generators  

E-Print Network (OSTI)

High penetration levels of distributed photovoltaic(PV) generation on an electrical distribution circuit present several challenges and opportunities for distribution utilities. Rapidly varying irradiance conditions may cause voltage sags and swells that cannot be compensated by slowly responding utility equipment resulting in a degradation of power quality. Although not permitted under current standards for interconnection of distributed generation, fast-reacting, VAR-capable PV inverters may provide the necessary reactive power injection or consumption to maintain voltage regulation under difficult transient conditions. As side benefit, the control of reactive power injection at each PV inverter provides an opportunity and a new tool for distribution utilities to optimize the performance of distribution circuits, e.g. by minimizing thermal losses. We discuss and compare via simulation various design options for control systems to manage the reactive power generated by these inverters. An important design de...

Sulc, Petr; Backhaus, Scott; Chertkov, Michael

2010-01-01T23:59:59.000Z

370

TL5002 Provides DDR Bus Termination Power Supply  

E-Print Network (OSTI)

Double data rate (DDR) bus termination power requirements bring new challenges to the power supply by requiring voltage tracking of a reference supply, requiring both sourcing and sinking current, and maintaining a high efficiency over a wide current range. This paper address these issues while presenting an example DDR design of 12 A of output current with voltage outputs between 0.9 V and 1.25 V. Issues and their solutions are provided for the power supply operating as a tradition buck power stage in the sourcing mode as well as for operating as a synchronous boost regulator in the sinking mode. Regulation and control loop characteristics of the examples are presented for both current sinking and sourcing modes of operation. Transient load response is also presented showing output voltage variation, as the current is transitioned from sourcing to sinking.

Robert Kollman; John Betten; Bang S. Lee

2001-01-01T23:59:59.000Z

371

Heat gain from power panelboard.  

E-Print Network (OSTI)

??This thesis focuses on estimating the power loss from power panelboards by means of power loss models. The model is intended to be used by (more)

Piesciorovsky, Emilio Carlos

2009-01-01T23:59:59.000Z

372

Vehicle Technologies Office: Power Electronics  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Electronics to Power Electronics to someone by E-mail Share Vehicle Technologies Office: Power Electronics on Facebook Tweet about Vehicle Technologies Office: Power Electronics on Twitter Bookmark Vehicle Technologies Office: Power Electronics on Google Bookmark Vehicle Technologies Office: Power Electronics on Delicious Rank Vehicle Technologies Office: Power Electronics on Digg Find More places to share Vehicle Technologies Office: Power Electronics on AddThis.com... Just the Basics Hybrid & Vehicle Systems Energy Storage Advanced Power Electronics & Electrical Machines Power Electronics Electrical Machines Thermal Control & System Integration Advanced Combustion Engines Fuels & Lubricants Materials Technologies Power Electronics The power electronics activity focuses on research and development (R&D)

373

Solartech Power | Open Energy Information  

Open Energy Info (EERE)

Solartech Power Jump to: navigation, search Name Solartech Power Place Cerritos, California Zip 90703 Sector Solar Product Solartech power is a distributer of solar modules....

374

Peak Power at Peak Efficiency  

Peak Power At Peak Efficiency. 21. st. Industry Growth Forum. October 2008. PJ Piper (857) 350?3100. ... At <$10/bbl oil, QM Powers electric ...

375

Microsoft PowerPoint - IP  

NLE Websites -- All DOE Office Websites (Extended Search)

U.S. Topics covered have included: * Sustainable Energy Development * Power Reactors * Nuclear Power Plant Planning * Nuclear Power Plant Pre-Operational Support IAEA's 10 Years...

376

Green Power Network: News Archive  

NLE Websites -- All DOE Office Websites (Extended Search)

to main content U.S. Department of Energy Energy Efficiency and Renewable Energy Green Power Network About the GPN Green Power Markets Buying Green Power Onsite Renewable...

377

Principle Power | Open Energy Information  

Open Energy Info (EERE)

Principle Power Place San Francisco, California Zip 94120 Sector Renewable Energy Product Principle Power is a global independent power producer committed to delivering green,...

378

Southwestern Power Administration One West...  

NLE Websites -- All DOE Office Websites (Extended Search)

of the United States Department of Energy Southwestern Power Administration Strategic Plan March 2013 Administrator's Message The Southwestern Power Administration powers the...

379

Energy Harvesting Aware Power Management  

E-Print Network (OSTI)

and J. Schiller, Utilizing solar power in wireless sensorthat only the actual solar power available, and not anyconverted to electric power using solar cells. The magnitude

Kansal, Aman; Srivastava, Mani B

2005-01-01T23:59:59.000Z

380

Factors Maintaining the Zonally Asymmetric Precipitation Distribution and Low-Level Flow in the Tropics of an Atmospheric General Circulation Model: Diagnostic Studies  

Science Conference Proceedings (OSTI)

The roles played by the large-scale motion induced by vertical diffusion of heat from the lower boundary and condensational heating due to deep convection in maintaining the precipitation zones in the Tropics of an atmospheric general circulation ...

David G. Dewitt; Edwin K. Schneider; Anandu D. Vernekar

1996-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Minimizing Failures While Maintaining Efficiency of Complex Interactive Networks and Systems: EPRI/DoD Complex Interactive Networks/ Systems Initiative; First Annual Report  

Science Conference Proceedings (OSTI)

This is the first annual report from the EPRI/DOD Complex Interactive Networks/Systems Initiative. The report describes research progress in minimizing failures while maintaining efficiency of complex interactive networks and systems.

2000-05-26T23:59:59.000Z

382

Reliability and maintainability study of select solar-energy-system components in the National Solar Data Network. Final subcontract report  

Science Conference Proceedings (OSTI)

This study reports on the reliability and maintainability of select solar energy system components evaluated in 16 solar heating and cooling systems over a one-year period. The systems evaluated were instrumented sites from the National Solar Data Network (NSDN). A complete description and system schematic for each site is provided. The study period was generally between October 1981 to October 1982. The report provides quantitative R and M data (e.g., Failure Rate and Mean Time Between Failures) on pumps, motors and fans from the selected NSDN sites, along with conclusions and recommendations based on comparative data for other components. In summary, pumps, valves, and heat exchangers in solar heating and cooling (SHAC) systems appear to be very reliable and show failure rates comparable to other mechanical system applications. Control systems typically used in SHAC systems appear to be the least reliable but still fall within the range of failures exhibited by other mechanical systems. Evidence suggests that piping leaks in SHAC systems occur at three times the rate of other mechanical systems. Recommendations are provided on other areas of research necessary to determine the useful life of SHAC system components. Finally, an appendix to this report describes actual failures encountered in the 16 systems evaluated.

Kendall, P.W.; Logee, T.L.; Raymond, M.G.

1983-06-01T23:59:59.000Z

383

Power Quality Aspects in a Wind Power Plant: Preprint  

SciTech Connect

Although many operational aspects affect wind power plant operation, this paper focuses on power quality. Because a wind power plant is connected to the grid, it is very important to understand the sources of disturbances that affect the power quality.

Muljadi, E.; Butterfield, C. P.; Chacon, J.; Romanowitz, H.

2006-01-01T23:59:59.000Z

384

Magnetic Materials for High Frequency Power Electronics  

Science Conference Proceedings (OSTI)

Mar 7, 2013 ... Advanced Materials for Power Electronics, Power Conditioning, and Power ... in power conditioning, conversion, and generation applications.

385

Application of the interphase power controller technology for transmission line power flow control  

SciTech Connect

This paper presents an application of the IPC technology for controlling power flows while maintaining the natural synchronizing capacity of transmission lines. The benefits for transmission systems are a substantial increase in steady-state transmission capability, lower losses and voltage support. An example based on the 500 kV Mead-Phoenix Project demonstrates the effectiveness of the IPC solution: the addition of a 370 Mvar capacitor in parallel with the two 500 kV phase-shifting transformers increases their maximum capability from 1,300 to 1,910 MW. The concepts presented are the results of the first phase of work leading to the development of an IPC using power electronics.

Brochu, J.; Beauregard, F.; Lemay, J.; Morin, G.; Pelletier, P. [Center d`Innovation sur le Transport d`Energie du Quebec, Varennes, Quebec (Canada)] [Center d`Innovation sur le Transport d`Energie du Quebec, Varennes, Quebec (Canada); Thallam, R.S. [Salt River Project, Phoenix, AZ (United States)] [Salt River Project, Phoenix, AZ (United States)

1997-04-01T23:59:59.000Z

386

Biomass: Potato Power  

NLE Websites -- All DOE Office Websites (Extended Search)

POTATO POWER POTATO POWER Curriculum: Biomass Power (organic chemistry, chemical/carbon cycles, plants, energy resources/transformations) Grade Level: Grades 2 to 3 Small groups (3 to 4) Time: 30 to 40 minutes Summary: Students assemble a potato battery that will power a digital clock. This shows the connection between renewable energy from biomass and its application. Provided by the Department of Energy's National Renewable Energy Laboratory and BP America Inc. BIOPOWER - POTATO POWER Purpose: Can a potato power a clock? Materials:  A potato  A paper plate  Two pennies  Two galvanized nails  Three 8 inch insulated copper wire, with 2 inches of the insulation removed from the ends  A digital clock (with places for wire attachment)

387

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Arkansas Power Electronics International, Inc. Arkansas Power Electronics International, Inc. DOE Peer Review November 2-3, 2006 Marcelo Schupbach, Ph.D. Senior Engineer APEI, Inc. 535 Research Center Blvd. Fayetteville, AR 72701 Phone: (479)-443-5759 Email: marcelo@apei.net Website: www.apei.net High Temperature and High Power Density SiC Power Electronic Converters Energy Storage Systems Program 2 Overview * APEI, Inc. Corporate Status * Broader Impact of SiC-based Power Converter * DOE Energy Storage System Program Phase I SBIR - SBIR Topic: Wide Band Gap Power Converter Application - APEI's Goals - Phase I Accomplishments * DOE Energy Storage System Program Phase II SBIR - APEI's Goals - Research Team and Partners - Project Status Energy Storage Systems Program 3 APEI, Inc. Mission Statement We are a small business dedicated to

388

DSW Power Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Projects Contact DSW Customers Customer Meetings Environmental Review-NEPA Operations & Maintenance Planning & Projects Power Marketing Power Projects Contact DSW Customers Customer Meetings Environmental Review-NEPA Operations & Maintenance Planning & Projects Power Marketing Rates DSW Power Projects Boulder Canyon: Straddling the Colorado River near the Arizona-Nevada border, Hoover Dam in Boulder Canyon creates Lake Mead. River waters turning turbines at Hoover Powerplant produce about 2,074 MW--enough electricity for nearly 8 million people. Western markets this power to public utilities in Arizona, California and Nevada over 53.30 circuit-miles of transmission line. Central Arizona: Authorized in 1968, the Central Arizona Project in Arizona and western New Mexico was built to improve water resources in the Colorado River Basin. Segments of the authorization allowed for Federal participation in the Navajo Generating Station. The Federal share of the powerplant's combined capacity is 547 MW.

389

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

11 North American Power Group, Ltd. 11 North American Power Group, Ltd. November 17, 2011 North American Power Group, Ltd. Two Elk Energy Park Carbon Site Characterization Study Preliminary Geologic Model-Update DOE NETL Annual Meeting November, 15-17, 2011 North American Power Group Copyright 2011 NAPG Two Elk Project Location 2 North American Power Group Copyright 2011 NAPG Work Flow and Project Integration 3 North American Power Group Copyright 2011 NAPG Modeling Approach  Model basin architecture is basically constructed from data within a 25 x 25 mile square area  Geologists reviewed data and correlated tops and surfaces  Porosity, permeability, petrophysics and other information correlated from that data to create a baseline model  Additional data has yet to be added from seismic information and from on-site penetrations

390

Solar power towers  

DOE Green Energy (OSTI)

The high desert near Barstow, California, has witnessed the development of this country's first two solar power towers. Solar One operated successfully from 1982 to 1988 and proved that power towers work efficiently to produce utility-scale power from sunlight. Solar Two was connected to the utility grid in 1996 and is operating today. Like its predecessor, Solar Two is rated at 10 megawatts. An upgrade of the Solar One plant, Solar Two demonstrates how solar energy can be stored in the form of heat in molten salt for power generation on demand. The experience gained with these two pilot power towers has established a foundation on which industry can develop its first commercial plants. These systems produce electricity on a large scale. They are unique among solar technologies because they can store energy efficiently and cost effectively. They can operate whenever the customer needs power, even after dark or during cloudy weather.

NONE

1998-04-01T23:59:59.000Z

391

Solar power towers  

DOE Green Energy (OSTI)

The high desert near Barstow, California, has witnessed the development of this country`s first two solar power towers. Solar One operated successfully from 1982 to 1988 and proved that power towers work efficiently to produce utility-scale power from sunlight. Solar Two was connected to the utility grid in 1996 and is operating today. Like its predecessor, Solar Two is rated at 10 megawatts. An upgrade of the Solar One plant, Solar Two demonstrates how solar energy can be stored in the form of heat in molten salt for power generation on demand. The experience gained with these two pilot power towers has established a foundation on which industry can develop its first commercial plants. These systems produce electricity on a large scale. They are unique among solar technologies because they can store energy efficiently and cost effectively. They can operate whenever the customer needs power, even after dark or during cloudy weather.

Not Available

1998-04-01T23:59:59.000Z

392

Power Quality Waveform Identification  

Science Conference Proceedings (OSTI)

This report describes the desired functionality, attributes and proposed development approach of a power quality (PQ) event identification tool that is planned to be developed under the Electric Power Research Institute (EPRI) Power Quality program P1.BackgroundPQ monitors capture a wide variety of disturbance events, ranging in frequency from direct current to a few megahertz. Advances in PQ monitoring and instrumentation allow continuous measurement and ...

2013-12-17T23:59:59.000Z

393

COSTS OF NUCLEAR POWER  

SciTech Connect

The discussion on the costs of nuclear power from stationary plants, designed primarily for the generation of electricity. deals with those plants in operation, being built, or being designed for construction at an early date. An attempt is made to consider the power costs on the basis of consistent definitions and assumptions for the various nuclear plants and for comparable fossil-fuel plants. Information on several new power reactor projects is included. (auth)

1961-01-01T23:59:59.000Z

394

Interleaved power converter  

DOE Patents (OSTI)

A power converter architecture interleaves full bridge converters to alleviate thermal management problems in high current applications, and may, for example, double the output power capability while reducing parts count and costs. For example, one phase of a three phase inverter is shared between two transformers, which provide power to a rectifier such as a current doubler rectifier to provide two full bridge DC/DC converters with three rather than four high voltage inverter legs.

Zhu, Lizhi (Canton, MI)

2007-11-13T23:59:59.000Z

395

SaskPower Small Power Producers Program (Saskatchewan, Canada) | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SaskPower Small Power Producers Program (Saskatchewan, Canada) SaskPower Small Power Producers Program (Saskatchewan, Canada) SaskPower Small Power Producers Program (Saskatchewan, Canada) < Back Eligibility Commercial Agricultural Industrial Residential Savings Category Solar Buying & Making Electricity Program Info Funding Source SaskPower State Saskatchewan Program Type Performance-Based Incentive Provider SaskPower The Small Power Producers Program accommodates customers who wish to generate up to 100 kilowatts (kW) of electricity for the purpose of offsetting power that would otherwise be purchased from SaskPower or for selling all of the power generated to SaskPower. At the beginning of the application process, you need to choose between one of two options: Sell all of the power you produce to SaskPower, or sell the

396

Karnataka Power Corporation Limited and National Thermal Power Corporation  

Open Energy Info (EERE)

Karnataka Power Corporation Limited and National Thermal Power Corporation Karnataka Power Corporation Limited and National Thermal Power Corporation JV Jump to: navigation, search Name Karnataka Power Corporation Limited and National Thermal Power Corporation JV Place India Sector Wind energy Product India-based wind power project developer. References Karnataka Power Corporation Limited and National Thermal Power Corporation JV[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Karnataka Power Corporation Limited and National Thermal Power Corporation JV is a company located in India . References ↑ "Karnataka Power Corporation Limited and National Thermal Power Corporation JV" Retrieved from "http://en.openei.org/w/index.php?title=Karnataka_Power_Corporation_Limited_and_National_Thermal_Power_Corporation_JV&oldid=3479

397

Application of EPRI's Transmission Reliability Evaluation for Large-Scale Systems (TRELSS) Program to Bonneville Power Administration System  

Science Conference Proceedings (OSTI)

Delivering power at the lowest cost while maintaining an acceptable level of reliability requires careful transmission planning. EPRI's Transmission Reliability Evaluation for Large-Scale Systems (TRELSS) can be used to analyze and quantify the reliability of bulk power systems to help determine the need for new transmission facilities. This report presents the results of reliability analyses for Bonneville Power Administration (BPA) using the TRELSS program.

1997-11-11T23:59:59.000Z

398

EIA Electric Power Forms  

Gasoline and Diesel Fuel Update (EIA)

Electric Power Forms Electric Power Forms EIA Electric Power Forms Listing of Publicly Available and Confidential Data EIA's statistical surveys encompass each significant electric supply and demand activity in the United States. Most of the electric power survey forms resulting data elements are published, but respondent confidentiality is required. The chart below shows the data elements for each survey form and how each data element is treated in regard to confidentiality. Data Categories Data collection forms EIA- 411 EIA- 826 EIA- 860 EIA- 860M EIA- 861 EIA- 923 Frame Information Utility identification and iocation -- -- -- -- X -- Plant identification and iocation -- -- -- X -- X Generation and fuel Latitude and longitude -- -- X -- -- --

399

Magnets and Power Supplies  

NLE Websites -- All DOE Office Websites (Extended Search)

Bibliography Up: APS Storage Ring Parameters Previous: Longitudinal Bibliography Up: APS Storage Ring Parameters Previous: Longitudinal bunch profile and Magnets and Power Supplies Dipole Magnets and Power Supplies Value Dipole Number 80+1 No. of power supplies 1 Magnetic length 3.06 m Core length 3.00 m Bending radius 38.9611 m Power supply limit 500.0 A Field at 7 GeV 0.599 T Dipole trim coils Number 80+1 No. of power supplies 80 Magnetic length 3.06 m Core length 3.00 m Power supply limit 20.0 A Maximum field 0.04 T Horizontal Correction Dipoles Number 317 No. of power supplies 317 Magnetic length 0.160 m Core length 0.07 m Power supply limit 150.0 A Maximum field 0.16 T Max. deflection at 7 GeV 1.1 mrad Vertical Corrector Dipoles Number 317 No. of power supplies 317

400

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

7 ANNUAL REPORT 7 ANNUAL REPORT Southwestern Power Administration Letter to the Secretary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About Southwestern. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Accomplishments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Supplementary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Power Purchase Agreements Update  

Energy.gov (U.S. Department of Energy (DOE))

Presentation covers an update on power purchase agreements and is given at the Spring 2011 Federal Utility Partnership Working Group (FUPWG) meeting.

402

Electric Power Annual  

Gasoline and Diesel Fuel Update (EIA)

Table 3.19. Net Generation from Geothermal by State, by Sector, 2011 and 2010 (Thousand Megawatthours) Electric Power Sector Census Division and State All Sectors Electric...

403

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

between alternative fuels and power plant communities needs to be improved Photosynthesis Biomass EtOH, Advanced biofuels Algae Pyrolysis oils Biodiesel, Advanced biofuels...

404

Power conversion technologies  

DOE Green Energy (OSTI)

The Power Conservation Technologies thrust area supports initiatives that enhance the core competencies of the Lawrence Livermore National Laboratory (LLNL) Engineering Directorate in the area of solid-state power electronics. Through partnerships with LLNL programs, projects focus on the development of enabling technologies for existing and emerging programs that have unique power conversion requirements. This year, a multi-disciplinary effort was supported which demonstrated solid-state, high voltage generation by using a dense, monolithic photovoltaic array. This effort builds upon Engineering's strengths in the core technology areas of power conversion, photonics, and microtechnologies.

Haigh, R E

1998-01-01T23:59:59.000Z

405

Electric Power Annual  

Annual Energy Outlook 2012 (EIA)

7. Net Generation from Wind by State, by Sector, 2011 and 2010 (Thousand Megawatthours) Electric Power Sector Census Division and State All Sectors Electric Utilities Independent...

406

Electric Power Annual  

U.S. Energy Information Administration (EIA) Indexed Site

4. Useful Thermal Output by Energy Source: Industrial Combined Heat and Power, 2001 - 2011 (Billion Btus) Period Coal Petroleum Liquids Petroleum Coke Natural Gas Other Gas Other...

407

Electric Power Annual  

U.S. Energy Information Administration (EIA) Indexed Site

C. Natural Gas: Consumption for Electricity Generation and Useful Thermal Output, by Sector, 2001 - 2011 (Million Cubic Feet) Electric Power Sector Period Total (all sectors)...

408

Electric Power Annual  

U.S. Energy Information Administration (EIA) Indexed Site

F. Coal: Consumption for Electricity Generation and Useful Thermal Output, by Sector, 2001 - 2011 (Billion Btus) Electric Power Sector Period Total (all sectors) Electric Utilities...

409

PowerPoint ????  

NLE Websites -- All DOE Office Websites (Extended Search)

of methanesteam reforming Strong endothermic reaction reactor water boiler steam Thermal energy combustor coal Steam generation in conventional power plant Synthetic use...

410

Municipal Electric Power (Minnesota)  

Energy.gov (U.S. Department of Energy (DOE))

This section describes energy procurement for local utilities operating in Minnesota and provides a means for Minnesota cities to construct and operate hydroelectric power plants. The statute gives...

411

RM Power Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

in 1990. The projects serve Colorado, Kansas, Nebraska and Wyoming with 830 MW of installed capacity and 3,360 miles of transmission line. About Power Marketing...

412

ELECTROCHEMICAL POWER FOR TRANSPORTATION  

E-Print Network (OSTI)

but the commercial electric vehicle industry continued tostrong interest in the electric vehicle industry to developTuyl, Effect of Electric Vehicles on the Power Industry, SAE

Cairns, Elton J.

2012-01-01T23:59:59.000Z

413

Electric Power Monthly  

U.S. Energy Information Administration (EIA)

Electric Power Monthly with Data for October 2012. December 2012 . Independent Statistics & Analysis . www.eia.gov . U.S. Department of Energy . ...

414

Electric Power Monthly  

U.S. Energy Information Administration (EIA)

Electric Power Monthly with Data for August 2012. October 2012 . Independent Statistics & Analysis . www.eia.gov . U.S. Department of Energy . ...

415

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

* Grain-oriented electrical steels for high efficiency power and distribution transformers. * Alloys for renewable energy systems. * Alloy design for optimization of...

416

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

June 7-8, 2006 Southwestern Power Administration Drought Operations Guides * Non-Hydro Guide Curve * Inflow trends * Drought Indices * Storage Remaining * Long-term weather...

417

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

Program Objectives Program Objective: Develop novel solvent and process for post- combustion capture of CO 2 from coal-fired power plants with 90% Capture efficiency, and...

418

Electric Power Annual  

Annual Energy Outlook 2012 (EIA)

4. Weighted Average Cost of Fossil Fuels for the Electric Power Industry, 2002 through 2011 Coal Petroleum Natural Gas Total Fossil Bituminous Subbituminous Lignite All Coal Ranks...

419

PowerPoint ?????????  

NLE Websites -- All DOE Office Websites (Extended Search)

Yongchen Song Dalian University of Technology Dalian, Liaoning China powere@dlut.edu.cn 13889533878 CO 2 Reduction and Ocean Storage Background CO 2 Storage Technology ...

420

Electric Power Annual 2004  

U.S. Energy Information Administration (EIA)

Energy Information Administration/Electric Power Annual 2004 iii Contacts Questions regarding this report may be directed to: Energy Information Administration, EI-53

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Balancing of Wind Power.  

E-Print Network (OSTI)

?? In the future, renewable energy share, especially wind power share, in electricity generation is expected to increase. Due to nature of the wind, wind (more)

lker, Muhammed Akif

2011-01-01T23:59:59.000Z

422

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

POTC Home Courses Instructors NERC Continuing Education Virtual University POTC Virtual University In an effort to expand electric power training opportunities while saving money...

423

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

POTC Home Courses Instructors NERC Continuing Education Virtual University Power Operations Training Center Instructors All instructors at Southwestern's POTC are NERC-approved...

424

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

POTC Home Courses Instructors NERC Continuing Education Virtual University 2013 Power Operations Training Center Courses Please follow the links on this page to view course...

425

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Market Monitoring Market Monitoring Tools Bernie Lesieutre - LBNL Bob Thomas - Cornell October 18, 2006 Washington, D.C. OE Visualization and Controls Peer Review Market Monitoring Tools: Overview Approach: Use dispatch, profit, revenue/offer price, withholding sensitivities to identify opportunities for local advantage that give some participants market power potential. 2006 Technical Work: Extend prior results to large, RTO-scale systems. Initiate large-scale analysis with RTO (PJM). Evaluate reactive power effects on energy markets. Publication and presentation of results. Market Power: Substitutability Market power boils down to the issue of substitutability Locational Advantage: "Load Pockets" Physical network constraints limit supply to certain loads, so that the incremental demand

426

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

- Chuck Herman and Guy Sliker * NGK - Hiroyuke Abe * EPRI funders (Con Edison, CPS Energy, HECO, Hydro One, NYISO, SDG&E, and TVA) 3 2009 Electric Power Research...

427

SOUTHWESTERN POWER ADMINISTRATION ANNUAL REPORT  

NLE Websites -- All DOE Office Websites (Extended Search)

and reliability. For example, we maintained our nearly 1,400 miles of high-voltage transmission lines, substations, and communications sites while achieving a Recordable...

428

Generalized power domination of graphs  

Science Conference Proceedings (OSTI)

In this paper, we introduce the concept of k-power domination which is a common generalization of domination and power domination. We extend several known results for power domination to k-power domination. Concerning the complexity of the k-power domination ... Keywords: Domination, Electrical network monitoring, Power domination

Gerard Jennhwa Chang; Paul Dorbec; Mickael Montassier; Andr Raspaud

2012-08-01T23:59:59.000Z

429

Green Power Network: News  

NLE Websites -- All DOE Office Websites (Extended Search)

News News TVA Seeks 126 MW of Renewables in 2014 December 2013 More News More News Subscribe to E-Mail Update Subscribe to e-mail update Events EPA Webinar - The Power of Aggregated Purchasing: How to Green Your Electricity Supply & Save Money January 15, 2014 1:00-2:00 p.m. ET Previous Webinars More News Features Green Power Market Status Report (2011 Data) Featured Green Power Reports News Archive Subscribe to Green Power News TVA Seeks 126 MW of Renewables in 2014 The Tennessee Valley Authority (TVA) is increasing the capacity of its renewable energy power purchase programs by 7 peercent over 2013, with a total capacity of 126 megawatts (MW) being offered. The increase in capacity is being spread across two of TVA's three power purchase programs - Green Power Providers, Solar Solutions Initiative, and the Renewable Standard Offer. The Green Power Providers program has 10 MW of available capacity for the development of small-scale solar, wind, biomass and hydro generation systems that are 50 kilowatts (kW) or less. Within the Green Power Providers program TVA has doubled the residential capacity from 2 MW to 4 MW and will be paying all power providers a total of 14¢ per kilowatt-hour (kWh). The Solar Solutions Initiative program, which focuses on installations between 50 kW and 1 MW, has been expanded from 10 MW of capacity to 16 MW and now pays a premium of 6¢/kWh. TVA's third power purchase program, the Renewable Standard Offer continues to have 100 MW of available capacity for projects between 1 MW and 20 MW. Prior to these program expansions TVA's renewables portfolio consisted of 128 MW of operating or committed solar, 1,500 MW of wind, and 60 MW of biomass.

430

New single-switch three-phase high power factor rectifiers using multi-resonant zero current switching  

E-Print Network (OSTI)

Abstract A new family of single-switch three-phase highpower-factor rectifiers, which have continuous input and output currents, is introduced. By using a multiresonant scheme, the transistor operates with zero-current switching (ZCS), and the diodes operate with zero-voltage switching (ZVS). These multiresonant rectifiers with a single transistor are capable of drawing a higher quality input-current waveform at nearly unity power factor and lower stresses than quasi-resonant rectifiers. Buck-type converters are used for the power stage, and, hence, the output voltage is lower than the input voltage. Moreover, these rectifiers have a wide load range and low stresses on semiconductor devices. From the analysis, normalized characteristics of the rectifier are derived. The design and breadboard implementation of the rectifier delivering 147 V? at 6 kW from a 30 240-V???@vvA input is described. The total harmonic distortion (THD) of the line current is less than 5%, and the system efficiency is about 94% at the full load. Index Terms Frequency control, multiresonant, power factor correction (PFC), resonant converters, three-phase rectifiers,

Yungtaek Jang; Robert W. Erickson

1994-01-01T23:59:59.000Z

431

Mercury Reactions in Power Plant Plumes: Pleasant Prairie Experiment and Compliance Scenario Assessment  

Science Conference Proceedings (OSTI)

Recent technical results indicate that divalent mercury emitted from power plants may rapidly transform to elemental mercury within power plant plumes. Simulations of mercury plume reduction based on these results have improved regional model fits with wet deposition data for particular years, while maintaining model-data fits for remaining archive years. Determining speciation changes occurring in a dispersing stack plume is essential for properly estimating atmospheric mercury fate and deposition patte...

2006-03-31T23:59:59.000Z

432

Peaking Service Experience at Kansas City Power and Light Hawthorn Station  

Science Conference Proceedings (OSTI)

EPRI's durability surveillance (DS) program -- in place since 1991 -- is producing the first in-service performance and operating data on the newest high-efficiency gas turbines. This detailed investigation of the Siemens V84.3A installed at the Kansas City Power & Light (KCPL) Hawthorn Station is providing plant personnel and the manufacturer with valuable information for solving initial problems. Program results will help all power producers specify, operate, and maintain a new generation of high-perfo...

1999-12-14T23:59:59.000Z

433

Control scheme for power modulation of a free piston Stirling engine  

DOE Patents (OSTI)

The present invention relates to a control scheme for power modulation of a free-piston Stirling engine-linear alternator power generator system. The present invention includes connecting an autotransformer in series with a tuning capacitance between a linear alternator and a utility grid to maintain a constant displacement to piston stroke ratio and their relative phase angle over a wide range of operating conditions.

Dhar, Manmohan (Schenectady, NY)

1989-01-01T23:59:59.000Z

434

Wind to Power Systems | Open Energy Information  

Open Energy Info (EERE)

Wind to Power Systems Wind to Power Systems Place Madrid, Spain Zip 28108 Sector Wind energy Product Wind to Power Systems designs, supplies and installs a device designed for use in wind turbines to provide fault ride-through capability, enabling wind turbines to maintain grid connection during periods of transmission line faults and voltage dips. Coordinates 40.4203°, -3.705774° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.4203,"lon":-3.705774,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

435

On Line Power Plant Performance Monitoring  

E-Print Network (OSTI)

Maintaining efficient and reliable plant operation is a prime objective in the generation of power. These are important considerations for utilities and particularly for Independent Power Producers as they become a more significant factor in the energy supply. On Line Performance Monitoring is an effective method to improve operating efficiency, detect and correct off nominal operation and expediently analyze cause and effect component performance relationships. The heart of a Performance Monitor is a modular collection of calculations used to determine performance indices in the power plant. Calculated performance indices are used in numerous applications: 1. To measure actual component performance compared to guaranteed or expected performance 2. To identify controllable operating problems and provide operator guidance in achieving the best operation of the plant 3. To evaluate component performance and deterioration for use in a maintenance program 4. To develop cost data and incremental cost characteristics for the economic operation or dispatch of the unit with other system energy sources 5. To document plant performance compared to base line data for the demonstration of efficient operation and improved availability. This paper will discuss the many advantages associated with a Performance Monitor system, their application, the benefits which may be realized and the potential of this concept with advanced diagnostic capability.

Ahner, D. J.; Priestley, R. R.

1990-06-01T23:59:59.000Z

436

NUCLEAR POWER PLANT  

DOE Patents (OSTI)

A nuclear power plant for use in an airless environment or other environment in which cooling is difficult is described. The power plant includes a boiling mercury reactor, a mercury--vapor turbine in direct cycle therewith, and a radiator for condensing mercury vapor. (AEC)

Carter, J.C.; Armstrong, R.H.; Janicke, M.J.

1963-05-14T23:59:59.000Z

437

Power Technologies Data Book  

SciTech Connect

This report, prepared by NREL's Energy Analysis Office, includes up-to-date information on power technologies, including complete technology profiles. The data book also contains charts on electricity restructuring, power technology forecasts and comparisons, electricity supply, electricity capability, electricity generation, electricity demand, prices, economic indicators, environmental indicators, conversion factors, and selected congressional questions and answers.

Goldstein, L.

2002-09-01T23:59:59.000Z

438

Fusion Power Deployment  

DOE Green Energy (OSTI)

Fusion power plants could be part of a future portfolio of non-carbon dioxide producing energy supplies such as wind, solar, biomass, advanced fission power, and fossil energy with carbon dioxide sequestration. In this paper, we discuss key issues that could impact fusion energy deployment during the last half of this century. These include geographic issues such as resource availability, scale issues, energy storage requirements, and waste issues. The resource needs and waste production associated with fusion deployment in the U.S. should not pose serious problems. One important feature of fusion power is the fact that a fusion power plant should be locatable within most local or regional electrical distribution systems. For this reason, fusion power plants should not increase the burden of long distance power transmission to our distribution system. In contrast to fusion power, regional factors could play an important role in the deployment of renewable resources such as wind, solar and biomass or fossil energy with CO2 sequestration. We examine the role of these regional factors and their implications for fusion power deployment.

J.A. Schmidt; J.M. Ogden

2002-02-06T23:59:59.000Z

439

New baseload power plants  

Science Conference Proceedings (OSTI)

This is a listing of 221 baseload power plant units currently in the planning stage. The list shows the plant owner, capacity, fuel, engineering firm, constructor, major equipment suppliers (steam generator, turbogenerator, and flue gas desulfurization system), partner, and date the plant is to be online. This data is a result of a survey by the journal of power plant owners.

Not Available

1994-04-01T23:59:59.000Z

440

Metagenomics Smart power grid  

E-Print Network (OSTI)

Metagenomics Smart power grid The new weapons workhorse Laser on Mars LOS ALAMOS SCIENCE'll read about a unique collaboration to create a "smart" power grid to accommodate an increasing, TECHNOLOGY, AND ENGINEERING 2 8 14 Dynamic Vision DARHT FULFILLS ITS DESTINY Solar Smart Grid in the Atomic

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

An Approach to Autonomous Control for Space Nuclear Power Systems  

SciTech Connect

Under Project Prometheus, the National Aeronautics and Space Administration (NASA) investigated deep space missions that would utilize space nuclear power systems (SNPSs) to provide energy for propulsion and spacecraft power. The initial study involved the Jupiter Icy Moons Orbiter (JIMO), which was proposed to conduct in-depth studies of three Jovian moons. Current radioisotope thermoelectric generator (RTG) and solar power systems cannot meet expected mission power demands, which include propulsion, scientific instrument packages, and communications. Historically, RTGs have provided long-lived, highly reliable, low-power-level systems. Solar power systems can provide much greater levels of power, but power density levels decrease dramatically at {approx} 1.5 astronomical units (AU) and beyond. Alternatively, an SNPS can supply high-sustained power for space applications that is both reliable and mass efficient. Terrestrial nuclear reactors employ varying degrees of human control and decision-making for operations and benefit from periodic human interaction for maintenance. In contrast, the control system of an SNPS must be able to provide continuous operatio for the mission duration with limited immediate human interaction and no opportunity for hardware maintenance or sensor calibration. In effect, the SNPS control system must be able to independently operate the power plant while maintaining power production even when subject to off-normal events and component failure. This capability is critical because it will not be possible to rely upon continuous, immediate human interaction for control due to communications delays and periods of planetary occlusion. In addition, uncertainties, rare events, and component degradation combine with the aforementioned inaccessibility and unattended operation to pose unique challenges that an SNPS control system must accommodate. Autonomous control is needed to address these challenges and optimize the reactor control design.

Wood, Richard Thomas [ORNL; Upadhyaya, Belle R. [University of Tennessee, Knoxville (UTK)

2011-01-01T23:59:59.000Z

442

Wind Powering America  

Wind Powering America (EERE)

These news items are notable additions These news items are notable additions to the Wind Powering America Web site. The Wind Powering America Web site reports recent national and state wind market changes by cataloging wind activities such as wind resource maps, small wind consumer's guides, local wind workshops, news articles, and publications in the areas of policy, public power, small wind, Native Americans, agricultural sector, economic development, public lands, and schools. en-us julie.jones@nrel.gov (Julie Jones) http://www.windpoweringamerica.gov/images/wpa_logo_sm.jpg Wind Powering America http://www.windpoweringamerica.gov/ Nominate an Electric Cooperative for Wind Power Leadership Award by January 15 http://www.windpoweringamerica.gov/filter_detail.asp?itemid=4076 http://www.windpoweringamerica.gov/filter_detail.asp?itemid=4076 Mon, 16

443

Fuel Cell Portable Power  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Power Department of Energy Workshop January 17, 2002 2 Portable Markets - Table of Contents 1. Opportunity Summary for Portable Markets 2. Commercialization Path and Resource Map 3. Value Chain Issues 4. Ballard "State of the Art" 5. Fuel Options and Issues 6. Where can the D.O.E. Help 3 Opportunity Summary - Portable Markets Infrequent Frequent Typical Applications Backup - Batteries & Gensets Peaking power and seasonal use; mobile power Preferred Fuels Hydrocarbon & Hydrogen Hydrocarbon (H2?) Total Available Market Large - But Fractured into many apps Moderate Price Target Low (Pockets willing to pay high $ for certain attributes) Moderate (Lifecycle) Environmental Impact Low Moderate Timing Short term Mid term 4 Technical Challenge Low High Micro Markets H2 Backup Power HC Frequent

444

EIA - Electric Power Data  

U.S. Energy Information Administration (EIA) Indexed Site

Survey-level Detail Data Files Survey-level Detail Data Files Electric power data are collected on survey instruments. Data collection is mandated by Congress to promote sound policymaking, efficient markets, and public understanding. The most widely used data are disseminated in reports, such as the Electric Power Monthly and the Electric Power Annual. Publicly available electric power data is available down to the plant level in the Electricity Data Browser and in detailed spreadsheets by survey below. Description Data availability State-level data (consolidated across forms) Contains electricity generation; fuel consumption; emissions; retail sales, revenue, number of customers, and retail prices; generating capacity; and financial data. 1990-2012 (monthly and annual) Electric power sales and revenue data - monthly (Form EIA-826)

445

Green Power Network: Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

News News TVA Seeks 126 MW of Renewables in 2014 December 2013 More News More News Subscribe to E-Mail Update Subscribe to e-mail update Events EPA Webinar - The Power of Aggregated Purchasing: How to Green Your Electricity Supply & Save Money January 15, 2014 1:00-2:00 p.m. ET Previous Webinars More News Features Green Power Market Status Report (2011 Data) Featured Green Power Reports Publications Alphabetical Listing Categorical Listing Chronological Listing Featured Reports The Green Power Network library contains articles and reports on green power, green pricing, and related topics. Whenever possible, we provide a link to publications available online. The publications are grouped by the following topics to help you in your search. If you are aware of other documents that should be added to this list, please notify our Webmaster.

446

Introduction to MEAG Power  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Introduction to MEAG Power Introduction to MEAG Power Southeastern Federal Power Alliance Meeting October 9, 2013 Municipal Electric Authority of Georgia ■ Joint Action Agency ─ Formed in 1975 ─ Owns and operates electric generation and transmission facilities ─ Provides bulk electric power to 48 cities and 1 county in the State of Georgia ■ All 49 Participants have reaffirmed 50-year power sales extensions ■ Take-or-pay contracts with participants are court validated contracts with a General Obligation pledge from each city ■ Generation ownership interest in 10 generating units and a transmission system ─ 2,069 MW generating capacity online ─ 500 MW Plant Vogtle Units 3 & 4 under development ■ Schedules the output from the SEPA contracts for the 49 members

447

Western Area Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

Loveland Area Projects November 29-30, 2011 2 Agenda * Overview of Western Area Power Administration * Post-1989 Loveland Area Projects (LAP) Marketing Plan * Energy Planning and Management Program * Development of the 2025 PMI Proposal * 2025 PMI Proposal * 2025 PMI Comment Period & Proposal Information * Questions 3 Overview of Western Area Power Administration (Western) * One of four power marketing administrations within the Department of Energy * Mission: Market and deliver reliable, renewable, cost-based Federal hydroelectric power and related services within a 15-state region of the central and western U.S. * Vision: Provide premier power marketing and transmission services Rocky Mountain Region (RMR) is one of five regional offices 4 Rocky Mountain Region

448

Power module assembly  

SciTech Connect

A power module assembly of the type suitable for deployment in a vehicular power inverter, wherein the power inverter has a grounded chassis, is provided. The power module assembly comprises a conductive base layer electrically coupled to the chassis, an insulating layer disposed on the conductive base layer, a first conductive node disposed on the insulating layer, a second conductive node disposed on the insulating layer, wherein the first and second conductive nodes are electrically isolated from each other. The power module assembly also comprises a first capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the first conductive node, and further comprises a second capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the second conductive node.

Campbell, Jeremy B. (Torrance, CA); Newson, Steve (Redondo Beach, CA)

2011-11-15T23:59:59.000Z

449

MHK Technologies/Vert Network Power Station | Open Energy Information  

Open Energy Info (EERE)

Network Power Station Network Power Station < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Vert Network Power Station.jpg Technology Profile Primary Organization Vert Labs LLP Technology Type Click here Point Absorber - Floating Technology Readiness Level Click here TRL 4 Proof of Concept Technology Description Vert Network is 1st cost effective wave power system that brings profit with the current level of pricing for renewable electricity The technology of Vert Network is based on an array of plastic floats that produce compressed air from the torque that is created from levers attached to the floats The compressed air is then sent to the shore by rubber pipe which is significantly cheaper and easier to maintain than underwater copper cables Consequently the generation is done on land using a standard turbine generator rather than requiring highly bespoke and overly robust generation devices which have to be specially designed for the marine environment and require specialist skills to maintain The marine based device is therefore made entirely from plastic carbon fibre and rubber so all the components are made from standard materials using mouldings and can be produced very cheaply VERT Labs estimates show that it can provide electricity at about 0 10 kWh When VERT Labs reache

450

Options for Control of Reactive Power by Distributed Photovoltaic Generators  

E-Print Network (OSTI)

High penetration levels of distributed photovoltaic(PV) generation on an electrical distribution circuit present several challenges and opportunities for distribution utilities. Rapidly varying irradiance conditions may cause voltage sags and swells that cannot be compensated by slowly responding utility equipment resulting in a degradation of power quality. Although not permitted under current standards for interconnection of distributed generation, fast-reacting, VAR-capable PV inverters may provide the necessary reactive power injection or consumption to maintain voltage regulation under difficult transient conditions. As side benefit, the control of reactive power injection at each PV inverter provides an opportunity and a new tool for distribution utilities to optimize the performance of distribution circuits, e.g. by minimizing thermal losses. We discuss and compare via simulation various design options for control systems to manage the reactive power generated by these inverters. An important design decision that weighs on the speed and quality of communication required is whether the control should be centralized or distributed (i.e. local). In general, we find that local control schemes are capable for maintaining voltage within acceptable bounds. We consider the benefits of choosing different local variables on which to control and how the control system can be continuously tuned between robust voltage control, suitable for daytime operation when circuit conditions can change rapidly, and loss minimization better suited for nighttime operation.

Petr Sulc; Konstantin Turitsyn; Scott Backhaus; Michael Chertkov

2010-08-04T23:59:59.000Z

451

Roles for Cardiac MyBP-C in Maintaining Myofilament Lattice Rigidity and Prolonging Myosin Cross-Bridge Lifetime  

Science Conference Proceedings (OSTI)

We investigated the influence of cardiac myosin binding protein-C (cMyBP-C) and its constitutively unphosphorylated status on the radial and longitudinal stiffnesses of the myofilament lattice in chemically skinned myocardial strips of the following mouse models: nontransgenic (NTG), effective null for cMyBP-C (t/t), wild-type cMyBP-C expressed into t/t (WT{sub t/t}), and constitutively unphosphorylated cMyBP-C (AllP{sub -t/t}). We found that the absence of cMyBP-C in the t/t and the unphosphorylated cMyBP-C in the AllP{sub -t/t} resulted in a compressible cardiac myofilament lattice induced by rigor not observed in the NTG and WT{sub t/t}. These results suggest that the presence and phosphorylation of the N-terminus of cMyBP-C provides structural support and radial rigidity to the myofilament lattice. Examination of myofilament longitudinal stiffness under rigor conditions demonstrated a significant reduction in cross-bridge-dependent stiffness in the t/t compared with NTG controls, but not in the AllP{sub -t/t} compared with WT{sub t/t} controls. The absence of cMyBP-C in the t/t and the unphosphorylated cMyBP-C in the AllP{sub -t/t} both resulted in a shorter myosin cross-bridge lifetime when myosin isoform was controlled. These data collectively suggest that cMyBP-C provides radial rigidity to the myofilament lattice through the N-terminus, and that disruption of the phosphorylation of cMyBP-C is sufficient to abolish this structural role of the N-terminus and shorten cross-bridge lifetime. Although the presence of cMyBP-C also provides longitudinal rigidity, phosphorylation of the N-terminus is not necessary to maintain longitudinal rigidity of the lattice, in contrast to radial rigidity.

Palmer, B.M.; Sadayappan, S.; Wang, Y.; Weith, A.E.; Previs, M.J.; Bekyarova, T.; Irving, T.C.; Robbins, J.; Maughan, D.W. (Vermont)

2011-10-06T23:59:59.000Z

452

Recursive operation time maximization model for the maintenance of power generation equipment  

Science Conference Proceedings (OSTI)

Repairable equipment requires preventive maintenance (PM) to maintain proper function. An appropriate PM strategy can extend the life of equipment and reduce variable costs. A power generation company in Taiwan that has a fixed-period PM strategy is ... Keywords: Maintenance improvement factor, Mathematical programming, Preventive maintenance (PM)

Der-Chiang Li; Chiao-Wen Liu; Tung-Liang Chen

2012-05-01T23:59:59.000Z

453

Guideline for the Seismic Technical Evaluation of Replacement Items for Nuclear Power Plants  

Science Conference Proceedings (OSTI)

This guideline provides practical, cost-effective techniques for reasonably assuring that replacement items will meet seismic performance requirements. Meeting such requirements is necessary to maintain the seismic design basis of commercial nuclear power plants. The guideline also offers a method for determining when a seismic technical evaluation of replacement items is required as part of the procurement process for spare and replacement items.

1993-06-01T23:59:59.000Z

454

Experimental Testing of a Hybrid Power Plant for a Dirigible UAV  

Science Conference Proceedings (OSTI)

Dirigibles have the ability to take off and land vertically, hover and maintain lift without consuming energy, and can be easily deflated for packaging and transportation. As such, dirigibles are well suited for surveillance and surveyance missions such ... Keywords: Dirigible, Energy efficient systems, Hybrid power plant, Long endurance, Low cost, Unmanned aerial vehicle, Variable pitch propeller

Steven Recoskie; Atef Fahim; Wail Gueaieb; Eric Lanteigne

2013-01-01T23:59:59.000Z

455

Analyzing Multiple-Product Power Markets: Simulation of Energy and Ancillary Services Prices and System Adequacy  

Science Conference Proceedings (OSTI)

The interpretation of price signals is a primary business task of power market participants, made more challenging by the shift from cost-based to bid-based pricing. This report outlines a novel pricing framework that accounts for the behavior and interaction of forward and real-time energy markets and the ancillary services required to maintain system reliability.

2000-12-01T23:59:59.000Z

456

Power-aware video decoding using real-time event handlers  

Science Conference Proceedings (OSTI)

Multimedia applications have to receive sufficient resource allocations to maintain their desired levels of Quality of Service (QoS). On the other hand, in mobile environments, the devices on which these applications must run have to minimize power consumption ... Keywords: energy, event service, mobile devices

Christian Poellabauer; Karsten Schwan

2002-09-01T23:59:59.000Z

457

MHK Technologies/PowerGin | Open Energy Information  

Open Energy Info (EERE)

PowerGin PowerGin < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage PowerGin.jpg Technology Profile Primary Organization Kinetic Wave Power Technology Resource Click here Wave Technology Type Click here Overtopping Technology Readiness Level Click here TRL 1 3 Discovery Concept Def Early Stage Dev Design Engineering Technology Description The energy conversion rate of the PowerGin is 20 30 The PowerGin makes use of both vertical and horizontal energy which allows the device to operate effectively in low wave states Buckets are mounted in a dense spiral pattern around the perimeter similar to hydro electric turbine blades which provide a high surface area to catch wave energy As the buckets on the ramp side of the rotor fill with wave water the rotors begin to turn Water is emptied out of the bucket instantaneously when it is submerged under the water by a patented gravity driven flap on the bottom The flap slams shut in one direction and opens in the other The two rotors rotate in opposite directions which maintain balance and continuous rotary power flow

458

Low-Rank Coal Grinding Performance Versus Power Plant Performance  

SciTech Connect

The intent of this project was to demonstrate that Alaskan low-rank coal, which is high in volatile content, need not be ground as fine as bituminous coal (typically low in volatile content) for optimum combustion in power plants. The grind or particle size distribution (PSD), which is quantified by percentage of pulverized coal passing 74 microns (200 mesh), affects the pulverizer throughput in power plants. The finer the grind, the lower the throughput. For a power plant to maintain combustion levels, throughput needs to be high. The problem of particle size is compounded for Alaskan coal since it has a low Hardgrove grindability index (HGI); that is, it is difficult to grind. If the thesis of this project is demonstrated, then Alaskan coal need not be ground to the industry standard, thereby alleviating somewhat the low HGI issue (and, hopefully, furthering the salability of Alaskan coal). This project studied the relationship between PSD and power plant efficiency, emissions, and mill power consumption for low-rank high-volatile-content Alaskan coal. The emissions studied were CO, CO{sub 2}, NO{sub x}, SO{sub 2}, and Hg (only two tests). The tested PSD range was 42 to 81 percent passing 76 microns. Within the tested range, there was very little correlation between PSD and power plant efficiency, CO, NO{sub x}, and SO{sub 2}. Hg emissions were very low and, therefore, did not allow comparison between grind sizes. Mill power consumption was lower for coarser grinds.

Rajive Ganguli; Sukumar Bandopadhyay

2008-12-31T23:59:59.000Z

459

High power linear pulsed beam annealer. [Patent application  

DOE Patents (OSTI)

A high power pulsed electron beam system for annealing semiconductors is comprised of an electron gun having a heated cathode, control grid and focus ring for confining the pulsed beam of electrons to a predetermined area, and a curved drift tube. The drift tube and an annular Faraday shield between the focus ring and the drift tube are maintained at a high positive voltage with respect to the cathode to accelerate electrons passing through the focus ring, thereby eliminating space charge limitations on the emission of electrons from said gun. A coil surrounding the curved drift tube provides a magnetic field which maintains the electron beam focused about the axis of the tube. The magnetic field produced by the coil around the curved tube imparts motion to electrons in a spiral path for shallow penetration of the electrons into a target. It also produces a scalloped profile of the electron beam. A second drift tube spaced a predetermined distance from the curved tube is positioned with its axis aligned with the axis of the first drift tube. The second drift tube and the target holder are maintained at a reference voltage between the cathode voltage and the curved tube voltage to decelerate the electrons. A second coil surrounding the second drift tube, maintains the electron beam focused about the axis of the second drift tube. The magnetic field of the second coil comprises the electron beam to the area of the semiconductor on the target holder.

Strathman, M.D.; Sadana, D.K.; True, R.B.

1980-11-26T23:59:59.000Z

460

Southwestern Power Administration One West Third Street  

NLE Websites -- All DOE Office Websites (Extended Search)

Policy Statement on Harassing Conduct Policy Statement on Harassing Conduct and Retaliation in the Workplace The purpose of this policy statement is to affirm the Southwestern Power Administration's (Southwestern) responsibility to maintain a workplace free from harassment and retaliation, and to ensure that all employees are aware of my personal commitment to this affirmation. Harassment is any unwelcome verbal, written, or physical conduct that either denigrates or shows hostility or aversion toward a person on the basis of sex, race, color, religion, age, national origin, disability (physical or mental), sexual orientation, status as a parent, or protected genetic information that: (1) has the purpose or effect of creating an intimidating, hostile, or offensive work environment; (2) has the purpose or effect of unreasonably interfering with an employee's

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Microsoft PowerPoint - Proceedings Cover Sheets  

NLE Websites -- All DOE Office Websites (Extended Search)

Climate Change Policy and Climate Change Policy and Technology: An Update Stephen D. Eule Director Climate Change Technology Program U.S. Department of Energy Fifth Annual Conference on Carbon Capture and Sequestration 9 May 2006 2 U.S. Approach U.S. approach to climate change harnesses the power of markets and technological innovation, maintains economic growth, and encourages global participation. Reaffirms U.S. commitment to goal of UNFCCC. Places climate change in a broader development context. Four basic elements: near-term policies & measures, including tax incentives; improved climate science; advanced technologies; and international collaboration. I reaffirm America's commitment to the United Nations Framework Convention and its central goal, to stabilize atmospheric

462

Transmission Issues and Power Exchanges in Texas  

E-Print Network (OSTI)

The electric transmission system in Texas has evolved over the years to its present state, in order to provide reliable service and reduce the amount of reserve capacity any individual utility needs to maintain. Presently there is pressure on the transmission owning utilities by several parties, primary distribution cooperatives, cogenerators, and large industrial customers, to grant wider access to the system. This pressure is coming at a time when transmission lines are becoming increasingly difficult to build. This paper presents a historical background on the development of the transmission system and describes the problems of assessing the impact and properly pricing certain bulk power transactions. In addition, it briefly describes the Electro-Magnetic Fields problem and how it relates to new transmission line construction.

Hughes, H. L.

1992-04-01T23:59:59.000Z

463

Microsoft PowerPoint - Walsh.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Historic Congestion in the Eastern Historic Congestion in the Eastern Interconnection Midwest ISO Overview and Comments Mike Walsh Senior Director UDS, EMS, Compliance and Training Spring 2009 Technical Workshop in Support of the DOE 2009 Congestion Study March 25, 2009 2 Who We Are * Independent, non-profit organization responsible for maintaining reliable transmission of power in 14 states and one Canadian province * First Regional Transmission Organization (RTO) approved by the Federal Energy Regulatory Commission (FERC) 3 1996 1999 Discussions begin to form Midwest ISO First Board of Directors elected 2002 FERC approval as an RTO Tariff Administration under Midwest ISO OATT 2005 Midwest Energy Markets Begin 2001 2006 Began Ancillary Services Market Initiative 2007 JOA with PJM Start-Up Reliability Coordination &

464

Enel Green Power- Innovative Geothermal Power for Nevada | Open Energy  

Open Energy Info (EERE)

Enel Green Power- Innovative Geothermal Power for Nevada Enel Green Power- Innovative Geothermal Power for Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to library Periodical: Enel Green Power- Innovative Geothermal Power for Nevada Abstract Two binary geothermal power plants inaugurated today with a total capacity of 65 MW: They will generate enough energy to meet the needs of some 40 thousand American households. Author Hank Sennott Published Press Release, 04/15/2009 DOI Not Provided Check for DOI availability: http://crossref.org Online Internet link for Enel Green Power- Innovative Geothermal Power for Nevada Citation Hank Sennott. 04/15/2009. Enel Green Power- Innovative Geothermal Power for Nevada. Press Release. 1-2. Retrieved from "http://en.openei.org/w/index.php?title=Enel_Green_Power-_Innovative_Geothermal_Power_for_Nevada&oldid=680547"

465

It's all About Power and those Pesky Power Vampires  

Science Conference Proceedings (OSTI)

In this issue of New Products, the editors cover an energy source that provides power for emergency situations and a car that helps to train drivers to drive energy efficiently. They also examine a power strip that defeats so-called 'power vampires' ... Keywords: Power vampires, smart power, Belkin, Truevert, Honda Insight, Husqvarna, Automower Solar Hybrid, Freeplay, Weza

Maria Ebling; Mark Corner

2009-01-01T23:59:59.000Z

466

Electric power annual 1992  

SciTech Connect

The Electric Power Annual presents a summary of electric utility statistics at national, regional and State levels. The objective of the publication is to provide industry decisionmakers, government policymakers, analysts and the general public with historical data that may be used in understanding US electricity markets. The Electric Power Annual is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels; Energy Information Administration (EIA); US Department of Energy. ``The US Electric Power Industry at a Glance`` section presents a profile of the electric power industry ownership and performance, and a review of key statistics for the year. Subsequent sections present data on generating capability, including proposed capability additions; net generation; fossil-fuel statistics; retail sales; revenue; financial statistics; environmental statistics; electric power transactions; demand-side management; and nonutility power producers. In addition, the appendices provide supplemental data on major disturbances and unusual occurrences in US electricity power systems. Each section contains related text and tables and refers the reader to the appropriate publication that contains more detailed data on the subject matter. Monetary values in this publication are expressed in nominal terms.

Not Available

1994-01-06T23:59:59.000Z

467

Power Economic Analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

CRSP Management Center CRSP Management Center Western Area Power Administration January 2011 Power Economic Analysis of Operational Restrictions at Glen Canyon Dam In February, 1997, the operating criteria for Glen Canyon Dam were changed. Operation was restricted to a Modified Low Fluctuating Flow as described in the Operation of Glen Canyon Dam, Colorado River Storage Project, Arizona, Final Environmental Impact Statement, March, 1995. These restrictions reduced the operating flexibility of the hydroelectric power plant and therefore the economic value of the electricity it produced. The Environmental Impact Statement provided impact information to support the Record of Decision governing dam operations. The impact

468

Wind Powering the Government  

DOE Green Energy (OSTI)

There are more than half a million Federal buildings with electric bills totaling about $3.5 billion per year. The Wind Powering America Initiative challenges the Federal government to reduce its use of energy produced by fossil fuels by obtaining at least 5% of its electricity from wind by 2010. As part of the current efforts to achieve the initiative's goal, NREL's Technical Information Services published Wind Powering the Government, a brochure that encourages the use of wind energy on Federal properties and the purchase of green power or green tags by Federal property managers.

Pitchford, P.

2000-08-02T23:59:59.000Z

469

Power supply apparatus  

SciTech Connect

The outputs of a plurality of modules or generators of electrical energy, such as fuel cells, chemical storage batteries, solar cells, MHD generators and the like, whose outputs are different are consolidated efficiently. The modules supply a power distribution system through an inverter. The efficiency is achieved by interconnecting the modules with an alternating voltage supply and electronic valves so controlled that the alternating-voltage supply absorbs power from modules whose output voltage is greater than the voltage at which the inverter operates and supplies this power as a booster to modules whose output voltage is less than the voltage at which the inverter operates.

Dickey, D. E.

1984-09-18T23:59:59.000Z

470

Computational power of correlations  

E-Print Network (OSTI)

We study the intrinsic computational power of correlations exploited in measurement-based quantum computation. By defining a general framework the meaning of the computational power of correlations is made precise. This leads to a notion of resource states for measurement-based \\textit{classical} computation. Surprisingly, the Greenberger-Horne-Zeilinger and Clauser-Horne-Shimony-Holt problems emerge as optimal examples. Our work exposes an intriguing relationship between the violation of local realistic models and the computational power of entangled resource states.

Janet Anders; Dan E. Browne

2008-05-07T23:59:59.000Z

471

Bonneville Power Administration Yakima Fisheries Project; 13Sept1996  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

BONNEVILLE POWER ADMINISTRATION BONNEVILLE POWER ADMINISTRATION YAKIMA FISHERIES PROJECT (YFP) RECORD OF DECISION Summary. As Administrator of the Bonneville Power Administration (BPA), I have decided to implement Alternative 2 of the proposed Yakima Fisheries Project (YFP) to undertake fishery research and mitigation activities in the Yakima River Basin in south- central Washington. The project responds directly to a need for knowledge of viable means to rebuild and maintain naturally spawning anadromous fish stocks in the Yakima Basin. Alternative 2 would experimentally supplement depressed populations of upper Yakima spring chinook salmon that spawn naturally, as well as undertake a study to determine the feasibility of re-establishing a naturally spawning population and significant fall fishery for coho salmon (now eliminated in the Basin).

472

PRESIDENTIAL PERMIT NORTHERN STATES POWER COMPANY ORDER NO. PP-231  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NORTHERN STATES POWER COMPANY NORTHERN STATES POWER COMPANY ORDER NO. PP-231 I. BACKGROUND The Office of Fossil Energy (FE) of the Department of Energy (DOE) has the responsibility for implementing Executive Order (EO) 10485, as amended by EO 12038, which requires the issuance of Presidential permits for the construction, operation, maintenance, and connection of electric transmission facilities at the United States international border. On November 2, 2000, Northern States Power Company (NSP) filed an application with the Office of Fossil Energy (FE) of the Department of Energy (DOE) for a Presidential permit to construct, operate, maintain, and connect an electric transmission line that would cross the U.S. border with Canada. NSP, doing business as Excel Energy Incorporated (Xcel), proposes to

473

Request for Information: Federal Government Power Purchase Agreements (PPA) Issues  

NLE Websites -- All DOE Office Websites (Extended Search)

Request for Information Request for Information Federal Government Power Purchase Agreements (PPA) Issues BACKGROUND: In order to respond to increasing demand for long term renewable energy, stemming from renewable goals established in the Energy Policy Act of 2005, Executive Order 13423, and the Energy Independence and Security Act of 2007, federal agencies are attempting to facilitate project development and the purchase of electricity from renewable sources on federal facilities. One means of execution is through the use of long term Power Purchase Agreements (PPAs), whereby a third party funds, develops, operates, maintains and owns a renewable energy project, and the Government commits to purchase the renewable power from the project owner. This method reduces the overall risk to the Government, since it will avoid having to build, own and

474

High Power Electrodynamics (HPE): Accelerator Operations and Technology,  

NLE Websites -- All DOE Office Websites (Extended Search)

CONTACTS CONTACTS Group Leader Bruce Carlsten Deputy Group Leader Ellen Guenette Administrator Josephine (Jo) Torres High-Power Electrodynamics (HPE) The High-Power Electrodynamics (AOT-HPE) Group applies accelerator and beam technologies to national-security-directed energy missions. AOT-HPE has three programmatic thrusts: free-electron lasers (FELs), high-power microwaves (HPM), and compact radiography. To maintain a vigorous and robust technical base for addressing DOE and DoD needs, the group's project portfolio is balanced between exploratory research, infrastructure development, and programmatic deliverables for sponsors. Funding is roughly 25% from the Lab's Directed Research and Development Program, 65% from DoD, and 10% from DOE. Technology Focus Areas AOT-HPE is the Laboratory's main vehicle for applying accelerator-based technologies to directed-energy mission needs. The group recognizes that many directed-energy missions are enabled by compact high-brightness electron accelerators and mm-wave and THz technologies.

475

Request for Information: Federal Government Power Purchase Agreements (PPA) Issues  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Request for Information Request for Information Federal Government Power Purchase Agreements (PPA) Issues BACKGROUND: In order to respond to increasing demand for long term renewable energy, stemming from renewable goals established in the Energy Policy Act of 2005, Executive Order 13423, and the Energy Independence and Security Act of 2007, federal agencies are attempting to facilitate project development and the purchase of electricity from renewable sources on federal facilities. One means of execution is through the use of long term Power Purchase Agreements (PPAs), whereby a third party funds, develops, operates, maintains and owns a renewable energy project, and the Government commits to purchase the renewable power from the project owner. This method reduces the overall risk to the Government, since it will avoid having to build, own and

476

Design and analysis of modern three-phase AC/AC power converters for AC drives and utility interface  

E-Print Network (OSTI)

Significant advances in modern ac/ac power converter technologies and demands of industries have reached beyond standard ac/ac power converters with voltage-source inverters fed from diode rectifiers. Power electronics converters have been matured to stages toward compact realization, increased high-power handling capability, and improving utility interface. Modern ac/ac power converter topologies with various control strategies have been introduced for the further improvements, such as matrix converters, current-fed converters, PWM rectifiers, and active power filters. In this dissertation, several new converter topologies are proposed in conjunction with developed control schemes based on the modern ac/ac converters which enhance performance and solve the drawbacks of conventional converters. In this study, a new fault-tolerant PWM strategy is first proposed for matrix converters. The added fault-tolerant scheme would strengthen the matrix converter technology for aerospace and military applications. A modulation strategy is developed to reshape output currents for continuous operation, against fault occurrence in matrix converter drives. This study designs a hybrid, high-performance ac/ac power converter for high power applications, based on a high-power load commutated inverter and a mediumpower voltage source inverter. Natural commutation of the load commutated inverter is actively controlled by the voltage source inverter. In addition, the developed hybrid system ensures sinusoidal output current/voltage waveforms and fast dynamic response in high power areas. A new topology and control scheme for a six-step current source inverter is proposed. The proposed topology utilizes a small voltage source inverter, to turn off main thyristor switches, transfer reactive load energy, and limit peak voltages across loads. The proposed topology maximizes benefits of the constituent converters: highpower handling capability of large thyristor-based current source inverters as well as fast and easy control of small voltage source inverters. This study analyzes, compares, and evaluates two topologies for unity power factor and multiple ac/ac power conversions. Theoretical analyses and comparisons of the two topologies, grounded on mathematical approaches, are presented from the standpoint of converter kVA ratings, dc-link voltage requirements, switch ratings, semiconductor losses, and reactive component sizes. Analysis, simulation, and experimental results are detailed for each proposed topology.

Kwak, Sangshin

2006-05-01T23:59:59.000Z

477

Power control system and method  

SciTech Connect

A power system includes an energy harvesting device, a battery coupled to the energy harvesting device, and a circuit coupled to the energy harvesting device and the battery. The circuit is adapted to deliver power to a load by providing power generated by the energy harvesting device to the load without delivering excess power to the battery and to supplement the power generated by the energy harvesting device with power from the battery if the power generated by the energy harvesting device is insufficient to fully power the load. A method of operating the power system is also provided.

Steigerwald, Robert Louis (Burnt Hills, NY); Anderson, Todd Alan (Niskayuna, NY)

2008-02-19T23:59:59.000Z

478

Quantification of Libby Reservoir Levels Needed to Maintain or Enhance Reservoir Fisheries, 1983-1987 Methods and Data Summary.  

DOE Green Energy (OSTI)

Libby Reservoir was created under an International Columbia River Treaty between the United States and Canada for cooperative water development of the Columbia River Basin. The authorized purpose of the dam is to provide power, flood control, and navigation and other benefits. Research began in May 1983 to determine how operations of Libby dam impact the reservoir fishery and to suggest ways to lessen these impacts. This study is unique in that it was designed to accomplish its goal through detailed information gathering on every trophic level in the reservoir system and integration of this information into a quantitative computer model. The specific study objectives are to: quantify available reservoir habitat, determine abundance, growth and distribution of fish within the reservoir and potential recruitment of salmonids from Libby Reservoir tributaries within the United States, determine abundance and availability of food organisms for fish in the reservoir, quantify fish use of available food items, develop relationships between reservoir drawdown and reservoir habitat for fish and fish food organisms, and estimate impacts of reservoir operation on the reservoir fishery. 115 refs., 22 figs., 51 tabs.

Chisholm, Ian

1989-12-01T23:59:59.000Z

479

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

Association Association S.2900 Reducing the Electric Power Carbon Footprint October 20, 2010 Richard S. Tuthill, Chair Board of Directors Gas Turbine Association 2 * Alstom Power * Florida Turbine Technologies * General Electric * Rolls Royce * Siemens Energy * Solar Turbines * Strategic Power Systems * United Technologies * Vibro Meter Gas Turbine Association 3 S.2900 * Introduced By Senator Kirsten Gillibrand (D-NY) * Prime Objective is to Fund Ground Power Gas Turbine Technologies - Raise Natural Gas Fired Gas Turbine Efficiencies ○ Phase One - Combined Cycle > 62%, Simple Cycle > 47% ○ Phase Two - Combined Cycle > 65%, Simple Cycle > 50% - Authorizes $340M Over Four Years ($85M per Year) - Combined Cycle, Simple Cycle, CHP, All Engine Sizes * Similar Bill Has Passed the US House (Under Suspension of Rules)

480

Wireless Power Transmission  

Office of Scientific and Technical Information (OSTI)

88 88 Lunar Wireless Power Transfer Feasibility Study March 2008 Prof. Zoya Popovic, University of Colorado, Boulder David R. Beckett, Scott R. Anderson, Diana Mann, Stuart Walker, Independent Consultants Sheldon Fried, Ph.D., National Security Technologies, LLC Abstract - This study examines the feasibility of a multi-kilowatt wireless radio frequency (RF) power system to transfer power between lunar base facilities. Initial analyses, show that wireless power transfer (WPT) systems can be more efficient and less expensive than traditional wired approaches for certain lunar and terrestrial applications. The study includes evaluations of the fundamental limitations of lunar WPT systems, the interrelationships of possible operational parameters, and a baseline design approach for a notionial system that could be used in the near

Note: This page contains sample records for the topic "maintain unity power" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

SOUTHWESTERN POWER ADMINISTRATION  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9/01 9/01 SOUTHWESTERN POWER ADMINISTRATION CATEGORICAL EXCLUSION (CX) DETERMINATION BRIEF DESCRIPTION OF PROPOSED ACTION: Hydroelectric Power Rate Increase for the Integrated System of Hydropower Projects. PROPOSED BY: Southwestern Power Administration. NUMBER AND TITLE OF THE CATEGORICAL EXCLUSION BEING APPLIED: ( 10 CFR 1021, Appendix B to Subpart D, 1-1-03 Edition, Part B4.3 - Electric power marketing rate changes. REGULATORY REQUIREMENTS IN 10 CFR 1021.410(B): (1) The proposed action fits within a class of actions that is listed in Appendix, A or B to Subpart D. (2) There are no extraordinary circumstances related to the proposal that may affect the Significance of the environmental effects of the proposal; and (3) The proposal is not "connected" to other actions with potentially significant impacts, is not related to

482

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

Skip Navigation Links Skip Navigation Links Annual Performance Plan Annual Report Mission Organization Strategic Plan SWPA - Overview Video System Map About the Agency Southwestern Power Administration was established in 1943 by the Secretary of the Interior as a Federal Agency that today operates within the Department of Energy under the authority of Section 5 of the Flood Control Act of 1944. As one of four Power Marketing Administrations in the United States, Southwestern markets hydroelectric power in Arkansas, Kansas, Louisiana, Missouri, Oklahoma, and Texas from 24 U.S. Army Corps of Engineers multipurpose dams. By law, Southwestern's power is marketed and delivered primarily to public bodies such as rural electric cooperatives and municipal utilities. Southwestern has over one hundred such "preference" customers, and these

483

PowerPoint Presentation  

U.S. Energy Information Administration (EIA) Indexed Site

David Sun, PhD David Sun, PhD david.sun@power.alstom.com Power Automation & Controls, Alstom Power Session: Intelligent Electric Systems Smart Power Future of Energy Sustainability © ALSTOM 2011. All rights reserved. Information contained in this document is provided without liability for information purposes only and is subject to change without notice. No representation or warranty is given or to be implied as to the completeness of information or fitness for any particular purpose. Reproduction, use or disclosure to third parties, without express written authority, is strictly prohibited. EIA Conference April 26, 2011 - EIA Conference 26 A Drivers for New Energy Eco-system Emission Management Distributed Empowerment Energy Efficiency Generation 40%

484

Linear Motor Powered Transportation  

E-Print Network (OSTI)

This special issue on linear-motor powered transportation covers both supporting technologies and innovative transport systems in various parts of the World, as this technology moves from the lab to commercial operations. ...

Thornton, Richard D.

485

Power conversion technologies  

DOE Green Energy (OSTI)

The Power Conversion Technologies thrust area identifies and sponsors development activities that enhance the capabilities of engineering at Lawrence Livermore National Laboratory (LLNL) in the area of solid- state power electronics. Our primary objective is to be a resource to existing and emerging LLNL programs that require advanced solid-state power electronic technologies.. Our focus is on developing and integrating technologies that will significantly impact the capability, size, cost, and reliability of future power electronic systems. During FY-96, we concentrated our research efforts on the areas of (1) Micropower Impulse Radar (MIR); (2) novel solid-state opening switches; (3) advanced modulator technology for accelerators; (4) compact accelerators; and (5) compact pulse generators.

Newton, M. A.

1997-02-01T23:59:59.000Z

486

Annual Power Electric  

U.S. Energy Information Administration (EIA) Indexed Site

Electric Power Annual Revision Final Data for 2011 Released: January 30, 2013 Revison Date: May 16, 2013 May 16, 2013 Data revision. 2011 Total (all sectors) and electric utility...

487

PowerPoint Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

Electrochemical Membrane for CO 2 Capture and Power Generation DE-FE0007634 Hossein Ghezel-Ayagh FuelCell Energy, Inc. 2013 NETL CO 2 Capture Technology Meeting July 10, 2013 Pittsburgh, PA FuelCell Energy, Inc. 1.4 MW plant at a municipal building 2.4 MW plant owned by an Independent power producer 600 kW plant at a food processor 11.2 MW plant - largest fuel cell park in the world Delivering ultra-clean baseload distributed generation globally Premier developer of stationary fuel cell products, with >40 years of experience Headquarters in Danbury, CT (USA), international presence in USA, Canada, Germany (Fraunhofer, IKTS) and South Korea (Posco) Delivering Direct FuelCell ® (DFC ® ) power plants for On-Site Power and Utility Grid

488

PowerPoint Presentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPA and Federal Hydropower APPA and Federal Hydropower Will Coffman Senior Government Relations Representative American Public Power Association Atlanta, Georgia Oct. 20, 2013 Overview * APPA, the American Public Power Association (APPA): trade association for the more than 2,000 community-owned, not-for- profit electric utilities providing service to 47 mil Americans in 49 states. Many of our members purchase power from Corps projects - Approx. 1,200 public power systems and rural electric cooperatives in 33 states. * We, along with NRECA, advocate for federal hydro customers in Congress and with the Administration Areas of Advocacy 1. Congress - Provide background on PMA customer issues to Committees of jurisdiction * Senate: Energy and Natural Resources * House: Natural Resources

489

SOUTHWESTERN POWER ADMINISTRATION  

NLE Websites -- All DOE Office Websites (Extended Search)

01 01 SOUTHWESTERN POWER ADMINISTRATION CATEGORICAL EXCLUSION (CX) DETERMINATION BRIEF DESCRIPTION OF PROPOSED ACTION: Hydroelectric Power Rate Increase for the Integrated System of Hydropower Projects. PROPOSED BY: Southwestern Power Administration. NUMBER AND TITLE OF THE CATEGORICAL EXCLUSION BEING APPLIED: ( 10 CFR 1021, Appendix B to Subpart D, 1-1-03 Edition, Part B4.3 - Electric power marketing rate changes. REGULATORY REQUIREMENTS IN 10 CFR 1021.410(B): (1) The proposed action fits within a class of actions that is listed in Appendix, A or B to Subpart D. (2) There are no extraordinary circumstances related to the proposal that may affect the Significance of the environmental effects of the proposal; and (3) The proposal is not "connected" to other actions with potentially significant impacts, is not related to

490

Geothermal Power Generation  

NLE Websites -- All DOE Office Websites (Extended Search)

1 GEOTHERMAL POWER GENERATION A PRIMER ON LOW-TEMPERATURE, SMALL-SCALE APPLICATIONS by Kevin Rafferty Geo-Heat Center January 2000 REALITY CHECK Owners of low-temperature...

491

The power tool  

Science Conference Proceedings (OSTI)

POWER Tool--Planning, Optimization, Waste Estimating and Resourcing tool, a hand-held field estimating unit and relational database software tool for optimizing disassembly and final waste form of contaminated systems and equipment.

HAYFIELD, J.P.

1999-02-01T23:59:59.000Z

492

Crowd-powered systems  

E-Print Network (OSTI)

Crowd-powered systems combine computation with human intelligence, drawn from large groups of people connecting and coordinating online. These hybrid systems enable applications and experiences that neither crowds nor ...

Bernstein, Michael Scott

2012-01-01T23:59:59.000Z

493

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

non-routine work to be performed at the Corps hydropower projects from which Southwestern markets power. Funding for this work averages a little over 20 million per year under an...

494

Southwestern Power Administration  

NLE Websites -- All DOE Office Websites (Extended Search)

Contact Us U.S. Department of Energy Southwestern Power Administration Gore Maintenance Office Mailing Address: P.O. Box 728 Gore, OK 74435-0728 Delivery Address: 14165 East 143rd...

495